Science.gov

Sample records for adding powdered activated

  1. Powdered activated carbon added biological treatment of pre-treated landfill leachate in a fed-batch reactor.

    PubMed

    Kargi, Fikret; Pamukoglu, M Yunus

    2003-05-01

    Biological treatment of landfill leachate usually results in low treatment efficiencies because of high chemical oxygen demand (COD), high ammonium-N content and also presence of toxic compounds such as heavy metals. A landfill leachate with high COD content was pre-treated by coagulation-flocculation followed by air stripping of ammonia at pH = 12. Pre-treated leachate was biologically treated in an aeration tank operated in fed-batch mode with and without addition of powdered activated carbon (PAC). PAC at 2 g l-1 improved COD and ammonium-N removals resulting in nearly 86% COD and 26% NH4-N removal.

  2. MODELING MERCURY CONTROL WITH POWDERED ACTIVATED CARBON

    EPA Science Inventory

    The paper presents a mathematical model of total mercury removed from the flue gas at coal-fired plants equipped with powdered activated carbon (PAC) injection for Mercury control. The developed algorithms account for mercury removal by both existing equipment and an added PAC in...

  3. Characterisation of spray dried soy sauce powders made by adding crystalline carbohydrates to drying carrier.

    PubMed

    Wang, Wei; Zhou, Weibiao

    2015-02-01

    This study aimed to reduce stickiness and caking of spray dried soy sauce powders by introducing a new crystalline structure into powder particles. To perform this task, soy sauce powders were formulated by using mixtures of cellulose and maltodextrin or mixtures of waxy starch and maltodextrin as drying carriers, with a fixed carrier addition rate of 30% (w/v) in the feed solution. The microstructure, crystallinity, solubility as well as stickiness and caking strength of all the different powders were analysed and compared. Incorporating crystalline carbohydrates in the drying carrier could significantly reduce the stickiness and caking strength of the powders when the ratio of crystalline carbohydrates to maltodextrin was above 1:5 and 1:2, respectively. X-ray Diffraction (XRD) results showed that adding cellulose or waxy starch could induce the crystallinity of powders. Differential Scanning Calorimetry (DSC) results demonstrated that the native starch added to the soy sauce powders did not fully gelatinize during spray drying.

  4. Effect of adding rubber powder to poplar particles on composite properties.

    PubMed

    Xu, Min; Li, Jian

    2012-08-01

    The effect of adding rubber powder derived from waste tires to poplar wood particles on mechanical and water-resistant properties of particleboards was examined. Sixty panels were made with rubber contents of 0-40% at hot-pressing temperatures of 140-180 °C, methylene diphenyl diisocyanate resin contents of 2-6% and panel densities of 0.6 to 1 g cm(-3). Although the modulus of rupture (MOR), modulus of elasticity (MOE), internal bond (IB) strength were reduced by adding rubber powder, the thickness swelling (TS) was reduced by 7.3-61% when 10-40% rubber powder was added. Four regression equations (rubber content, pressing temperature, resin content and target panel density as functions of MOR, MOE, IB and TS) were developed and a nonlinear programing model was derived with operation research theory to obtain the most desirable panel properties under some production constraints.

  5. Effect of adding rubber powder to poplar particles on composite properties.

    PubMed

    Xu, Min; Li, Jian

    2012-08-01

    The effect of adding rubber powder derived from waste tires to poplar wood particles on mechanical and water-resistant properties of particleboards was examined. Sixty panels were made with rubber contents of 0-40% at hot-pressing temperatures of 140-180 °C, methylene diphenyl diisocyanate resin contents of 2-6% and panel densities of 0.6 to 1 g cm(-3). Although the modulus of rupture (MOR), modulus of elasticity (MOE), internal bond (IB) strength were reduced by adding rubber powder, the thickness swelling (TS) was reduced by 7.3-61% when 10-40% rubber powder was added. Four regression equations (rubber content, pressing temperature, resin content and target panel density as functions of MOR, MOE, IB and TS) were developed and a nonlinear programing model was derived with operation research theory to obtain the most desirable panel properties under some production constraints. PMID:22705506

  6. Final report for the ASC gas-powder two-phase flow modeling project AD2006-09.

    SciTech Connect

    Evans, Gregory Herbert; Winters, William S.

    2007-01-01

    This report documents activities performed in FY2006 under the ''Gas-Powder Two-Phase Flow Modeling Project'', ASC project AD2006-09. Sandia has a need to understand phenomena related to the transport of powders in systems. This report documents a modeling strategy inspired by powder transport experiments conducted at Sandia in 2002. A baseline gas-powder two-phase flow model, developed under a companion PEM project and implemented into the Sierra code FUEGO, is presented and discussed here. This report also documents a number of computational tests that were conducted to evaluate the accuracy and robustness of the new model. Although considerable progress was made in implementing the complex two-phase flow model, this project has identified two important areas that need further attention. These include the need to compute robust compressible flow solutions for Mach numbers exceeding 0.35 and the need to improve conservation of mass for the powder phase. Recommendations for future work in the area of gas-powder two-phase flow are provided.

  7. Process for preparing active oxide powders

    DOEpatents

    Berard, Michael F.; Hunter, Jr., Orville; Shiers, Loren E.; Dole, Stephen L.; Scheidecker, Ralph W.

    1979-02-20

    An improved process for preparing active oxide powders in which cation hydroxide gels, prepared in the conventional manner are chemically dried by alternately washing the gels with a liquid organic compound having polar characteristics and a liquid organic compound having nonpolar characteristics until the mechanical water is removed from the gel. The water-free cation hydroxide is then contacted with a final liquid organic wash to remove the previous organic wash and speed drying. The dried hydroxide treated in the conventional manner will form a highly sinterable active oxide powder.

  8. USING POWDERED ACTIVATED CARBON: A CRITICAL REVIEW

    EPA Science Inventory

    Because the performance of powdered activated carbon (PAC) for uses other than taste and odor control is poorly documented, the purpose of this article is to critically review uses that have been reported (i.e., pesticides and herbicides, synthetic organic chemicals, and trihalom...

  9. Reducing retrogradation and lipid oxidation of normal and glutinous rice flours by adding mango peel powder.

    PubMed

    Siriamornpun, Sirithon; Tangkhawanit, Ekkarat; Kaewseejan, Niwat

    2016-06-15

    Green and ripe mango peel powders (MPP) were added to normal rice flour (NRF) and glutinous rice flour (GRF) at three levels (400, 800 and 1200 ppm) and their effects on physicochemical properties and lipid oxidation inhibition were investigated. Overall, MPP increased the breakdown viscosity and reduced the final viscosity in rice flours when compared to the control. Decreasing in retrogradation was observed in both NRF and GRF with MPP added of all levels. MPP addition also significantly inhibited the lipid oxidation of all flours during storage (30 days). Retrogradation values were strongly negatively correlated with total phenolic and flavonoid contents, but not with fiber content. The hydrogen bonds and hydrophilic interactions between phenolic compounds with amylopectin molecule may be involved the decrease of starch retrogradation, especially GRF. We suggest that the addition of MPP not only reduced the retrogradation but also inhibited the lipid oxidation of rice flour. PMID:26868561

  10. Reducing retrogradation and lipid oxidation of normal and glutinous rice flours by adding mango peel powder.

    PubMed

    Siriamornpun, Sirithon; Tangkhawanit, Ekkarat; Kaewseejan, Niwat

    2016-06-15

    Green and ripe mango peel powders (MPP) were added to normal rice flour (NRF) and glutinous rice flour (GRF) at three levels (400, 800 and 1200 ppm) and their effects on physicochemical properties and lipid oxidation inhibition were investigated. Overall, MPP increased the breakdown viscosity and reduced the final viscosity in rice flours when compared to the control. Decreasing in retrogradation was observed in both NRF and GRF with MPP added of all levels. MPP addition also significantly inhibited the lipid oxidation of all flours during storage (30 days). Retrogradation values were strongly negatively correlated with total phenolic and flavonoid contents, but not with fiber content. The hydrogen bonds and hydrophilic interactions between phenolic compounds with amylopectin molecule may be involved the decrease of starch retrogradation, especially GRF. We suggest that the addition of MPP not only reduced the retrogradation but also inhibited the lipid oxidation of rice flour.

  11. Antiviral activities of heated dolomite powder.

    PubMed

    Motoike, Koichi; Hirano, Shozo; Yamana, Hideaki; Onda, Tetsuhiko; Maeda, Takayoshi; Ito, Toshihiro; Hayakawa, Motozo

    2008-12-01

    The effect of the heating conditions of dolomite powder on its antiviral activity was studied against the H5N3 avian influenza virus. Calcium oxide (CaO) and magnesium oxide (MgO), obtained by the thermal decomposition of dolomite above 800 degrees C, were shown to have strong antiviral activity, but the effect was lessened when the heating temperature exceeded 1400 degrees C. Simultaneous measurement of the crystallite size suggested that the weakening of the activity was due to the considerable grain growth of the oxides. It was found that the presence of Mg in dolomite contributed to the deterrence of grain growth of the oxides during the heating process. Although both CaO and MgO exhibited strong antiviral activity, CaO had the stronger activity but quickly hydrated in the presence of water. On the other hand, the hydration of MgO took place gradually under the same conditions. Separate measurements using MgO and Mg(OH)2 revealed that MgO had a higher antiviral effect than Mg(OH)2. From the overall experiments, it was suggested that the strong antiviral activity of dolomite was related to the hydration reaction of CaO. PMID:19127652

  12. POSSIBLE CHROMOSPHERIC ACTIVITY CYCLES IN AD LEO

    SciTech Connect

    Buccino, Andrea P.; Petrucci, Romina; Mauas, Pablo J. D.; Jofré, Emiliano

    2014-01-20

    AD Leo (GJ 388) is an active dM3 flare star that has been extensively observed both in the quiescent and flaring states. Since this active star is near the fully convective boundary, studying its long-term chromospheric activity in detail could be an appreciable contribution to dynamo theory. Here, using the Lomb-Scargle periodogram, we analyze the Ca II K line-core fluxes derived from CASLEO spectra obtained between 2001 and 2013 and the V magnitude from the ASAS database between 2004 and 2010. From both of these totally independent time series, we obtain a possible activity cycle with a period of approximately seven years and a less significant shorter cycle of approximately two years. A tentative interpretation is that a dynamo operating near the surface could be generating the longer cycle, while a second dynamo operating in the deep convection zone could be responsible for the shorter one. Based on the long duration of our observing program at CASLEO and the fact that we observe different spectral features simultaneously, we also analyze the relation between simultaneous measurements of the Na I index (R{sub D}{sup ′}), Hα, and Ca II K fluxes at different activity levels of AD Leo, including flares.

  13. Kinetics of adsorption with granular, powdered, and fibrous activated carbon

    SciTech Connect

    Shmidt, J.L.; Pimenov, A.V.; Lieberman, A.I.; Cheh, H.Y.

    1997-08-01

    The properties of three different types of activated carbon, fibrous, powdered, and granular, were investigated theoretically and experimentally. The adsorption rate of the activated carbon fiber was found to be two orders of magnitude higher than that of the granular activated carbon, and one order of magnitude higher than that of the powdered activated carbon. Diffusion coefficients of methylene blue in the fibrous, powdered, and granular activated carbons were determined experimentally. A new method for estimating the meso- and macropore surface areas in these carbons was proposed.

  14. Microstructural and phase evolution in metakaolin geopolymers with different activators and added aluminosilicate fillers

    NASA Astrophysics Data System (ADS)

    Sarkar, Madhuchhanda; Dana, Kausik; Das, Sukhen

    2015-10-01

    This work aims to investigate the microstructural and phase evolution of alkali activated metakaolin products with different activators and added aluminosilicate filler phases. The added filler phases have different reactivity to the alkali activated metakaolin system. Microstructural evolution in the alkali activated products has been investigated by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Field Emission Scanning Electron Microscope (FESEM). Variation in strength development in alkali activated metakaolin products was followed by compressive strength measurement test. Microstructural study shows that in case of metakaolin with NaOH activator crystalline sodalite formed in all the product samples irrespective of the added filler phases. The microstructure of these NaOH activated products investigated by FESEM showed crystalline and inhomogeneous morphology. Mixed activator containing both NaOH and sodium silicate in a fixed mass ratio formed predominantly amorphous phase. Microstructure of these samples showed more homogeneity than that of NaOH activated metakaolin products. The study further shows that addition of α-Al2O3 powder, non reactive phase to the alkali activated metakaolin system when used in larger amount increased crystalline phase in the matrix. α-Al2O3 powder addition increased the compressive strength of the product samples for both the activator compositions. Added phase of colloidal silica, reactive to the alkali activated metakaolin system when used in larger amount was found to increase amorphous nature of the matrix. Addition of colloidal silica influenced the compressive strength property differently with different activator compositions.

  15. Effect of bread baking on the bioavailability of hydrogen-reduced iron powder added to unenriched refined wheat flour.

    PubMed

    Maekawa, Atsushi A; Glahn, Raymond P; Lei, Xin Gen; Miller, Dennis D

    2006-10-18

    Elemental iron powders are widely used to fortify flour and other cereal products. Our objective was to test the hypothesis that baking enhances the bioavailability of elemental iron powders by oxidizing Fe(0) to Fe(2+) or Fe(3+). An in vitro digestion/Caco-2 cell culture model and a piglet model were used to measure bioavailability. Bread flour, either unfortified or fortified with hydrogen-reduced (HR) iron powder or FeSO(4) (300 mg Fe/kg flour), was baked into bread. For the in vitro studies, bread samples were treated with pepsin at pH 2, 3, 4, 5, 6, or 7 and subsequently incubated with pancreatic enzymes at pH 7 in a chamber positioned above monolayers of cultured Caco-2 cells. Ferritin formation in the cells was used as an index of iron bioavailability. Ferritin formation in cells fed HR Fe bread was similar to cells fed FeSO(4) bread when the peptic digestion was conducted at a pH 2 but lower when the peptic phase was conducted at pH 3, 4, 5, 6, or 7 (P < 0.05). Pig diets containing 35% dried bread were prepared and fed to cross-bred (Hampshire x Landrace x Yorkshire) anemic pigs in two studies. The rate of increase in hemoglobin Fe over the feeding period was used to calculate relative biological value (RBV), an index of iron bioavailability. In the first pig study, RBV of HR Fe added to flour prior to baking was 47.9% when compared to FeSO(4) fortified flour (P < 0.05). In the second pig study, a third treatment consisting of unfortified bread with HR iron added during diet mixing (after bread baking) was included. RBVs of the HR Fe diet (Fe added after baking) and HR Fe diet (Fe added before baking) were 40.1% and 53.5%, respectively, compared to the FeSO(4) diet. Differences in RBV between the HR Fe (before and after baking) and FeSO(4) (before baking) treatment groups were significant, but the difference between the before and after HR treatment groups was not significant. We conclude that bread baking does not enhance the bioavailability of elemental

  16. Interactions between organic additives and active powders in water-based lithium iron phosphate electrode slurries

    NASA Astrophysics Data System (ADS)

    Li, Chia-Chen; Lin, Yu-Sheng

    2012-12-01

    The interactions of organic additives with active powders are investigated and are found to have great influence on the determination of the mixing process for preparing electrode slurries with good dispersion and electrochemical properties of lithium iron phosphate (LiFePO4) electrodes. Based on the analyses of zeta potential, sedimentation, and rheology, it is shown that LiFePO4 prefers to interact with styrene-butadiene rubber (SBR) relative to other organic additives such as sodium carboxymethyl cellulose (SCMC), and thus shows preferential adsorption by SBR, whereas SBR has much lower efficiency than SCMC in dispersing LiFePO4. Therefore, for SCMC to interact with and disperse LiFePO4 before the interaction of LiFePO4 with SBR, it is suggested to mix SCMC with LiFePO4 prior to the addition of SBR during the slurry preparation process. For the electrode prepared via the suggested process, i.e., the sequenced adding process in which SCMC is mixed with active powders prior to the addition of SBR, a much better electrochemical performance is obtained than that of the one prepared via the process referred as the simultaneous adding process, in which mixing of SCMC and SBR with active powders in simultaneous.

  17. Physicochemical and sensory characteristics of fat-free goat milk yogurt with added stabilizers and skim milk powder fortification.

    PubMed

    Bruzantin, F P; Daniel, J L P; da Silva, P P M; Spoto, M H F

    2016-05-01

    Goat milk yogurt has a less consistent coagulum compared with cow milk yogurt; furthermore, the presence of goat milk in foodstuffs imparts a characteristic flavor that can restrict its acceptance by consumers. This study aimed to assess and compare the physicochemical and sensory characteristics of fat-free goat milk yogurts with added stabilizers or bovine skim milk powder to improve the final product. Four treatment additions were evaluated: (1) a mixture of 0.1% (wt/vol) carrageenan and 0.1% (wt/vol) pectin (treatment CR); (2) 0.5% (wt/vol) pectin (treatment PE); (3) 4.65% (wt/vol) bovine skim milk powder (treatment BM); and (4) control (no stabilizer; treatment CT). The physicochemical parameters were investigated at on d 1 and 5 of storage. The BM treatment presented higher pH and titratable acidity values, resulting in a buffering capacity effect. The total crude protein (CP) and solids-not-fat (SNF) contents were also higher in BM compared with the other evaluated treatments because of the addition of bovine skim milk powder. We detected a reduction in pH values for all treatments. Lower SNF contents were present in the CR and CT treatments, which might be related to a syneresis process during storage; moreover, an increase in total CP was observed for all treatments due to the proteolytic action of the starter culture. Sensory attributes, including appearance (color, consistency, and presence of lumps), texture (consistency, viscosity, and presence of lumps), flavor (bitter, sweet, and characteristic of commercial plain nonfat yogurt), and overall impression were evaluated by quantitative descriptive analysis. The addition of 0.5% (wt/vol) of pectin (PE treatment) strengthened the curd; however, the visual and oral presence of lumps and a higher bitterness score were noted by trained panelists, which resulted in the lowest overall impression score for the PE treatment. In several sensory attributes, the CR treatment was considered similar to the control

  18. Variations of 14C around AD 775 and AD 1795 - due to solar activity

    NASA Astrophysics Data System (ADS)

    Neuhäuser, R.; Neuhäuser, D. L.

    2015-12-01

    The motivation for our study is the disputed cause for the strong variation of 14C around AD 775. Our method is to compare the 14C variation around AD 775 with other periods of strong variability. Our results are: (a) We see three periods, where 14C varied over 200 yr in a special way showing a certain pattern of strong secular variation: after a Grand Minimum with strongly increasing 14C, there is a series of strong short-term drop(s), rise(s), and again drop(s) within 60 yr, ending up to 200 yr after the start of the Grand Minimum. These three periods include the strong rises around BC 671, AD 775, and AD 1795. (b) We show with several solar activity proxies (radioisotopes, sunspots, and aurorae) for the AD 770s and 1790s that such intense rapid 14C increases can be explained by strong rapid decreases in solar activity and, hence, wind, so that the decrease in solar modulation potential leads to an increase in radioisotope production. (c) The strong rises around AD 775 and 1795 are due to three effects, (i) very strong activity in the previous cycles (i.e. very low 14C level), (ii) the declining phase of a very strong Schwabe cycle, and (iii) a phase of very weak activity after the strong 14C rise - very short and/or weak cycle(s) like the suddenly starting Dalton minimum. (d) Furthermore, we can show that the strong change at AD 1795 happened after a pair of two packages of four Schwabe cycles with certain hemispheric leadership (each package consists of two Gnevyshev-Ohl pairs, respectively two Hale-Babcock pairs). We show with several additional arguments that the rise around AD 775 was not that special. We conclude that such large, short-term rises in 14C (around BC 671, AD 775, and 1795) do not need to be explained by highly unlikely solar super-flares nor other rare events, but by extra-solar cosmic rays modulated due to solar activity variations.

  19. Coercivity enhancement of Nd-Fe-B sintered magnets with intergranular adding (Pr, Dy, Cu)-Hx powders

    NASA Astrophysics Data System (ADS)

    Zhang, Yujing; Ma, Tianyu; Liu, Xiaolian; Liu, Pan; Jin, Jiaying; Zou, Junding; Yan, Mi

    2016-02-01

    Forming Nd2Fe14B/(Nd, Dy)2Fe14B core-shell structure by intergranular adding Dy-containing sources into Nd-Fe-B sintered magnets is effective to improve coercivity and to minimize remanence loss simultaneously. However, the excessive Dy located in the intergranular regions has nearly no hard magnetic contribution, causing its low utilization efficiency. In this work, diluted Dy powders (Pr37Dy30Cu33)-Hx were prepared and incorporated into Nd-Fe-B sintered magnets via a dual-alloy approach. The coercivity increases rapidly from 15.0 to 18.2 kOe by 21.3% with 2.0 wt% (Pr, Dy, Cu)-Hx addition (the equivalent Dy is only 0.32 at%). The deduced coercivity incremental ratio is 10.0 kOe per unit Dy at%. Dehydrogenation reaction of (Pr, Dy, Cu)-Hx occurs during sintering, which favors Dy diffusion towards the 2:14:1 phase grains as well as smoothing the grain boundaries (GBs). The enhanced local anisotropic field and the well decoupled 2:14:1 phase grains contribute to such rapid coercivity enhancement. This work suggests that adding diluted Dy hydrides is promising for fabricating high coercivity Nd-Fe-B sintered magnets with less heavy rare-earth consumption.

  20. Improvement of the Dimensional Stability of Powder Injection Molded Compacts by Adding Swelling Inhibitor into the Debinding Solvent

    NASA Astrophysics Data System (ADS)

    Fan, Yang-Liang; Hwang, Kuen-Shyang; Su, Shao-Chin

    2008-02-01

    Defects are frequently found in powder injection molded (PIM) compacts during solvent debinding due to the swelling of the binders. This problem can be alleviated by adjusting the composition of the debinding solvent. In this study, 10 vol pct swelling inhibitors were added into heptane, and the in-situ amounts of swelling and sagging of the specimen in the solvent were recorded using a noncontacting laser dilatometer. The results show that the addition of ethanol, 2-propanol, 1-butanol, and 1-pentanol reduced the amounts of swelling by 31, 21, 17, and 11 pct, respectively. This was because the small molecule alcohols, which do not dissolve paraffin wax (PW) or stearic acid (SA) in the binder system, could diffuse easily into the specimen and increased the portion of the swelling inhibitor inside. The amount of the extracted PW and SA also decreased, but only by 8.3, 6.1, 4.3, and 2.4 pct, respectively. The solubility parameters of 1-bromopropane (n-PB) and ethyl acetate (EA) are between those of heptane and alcohols, and they also yielded a slight reduction in the amounts of swelling by 6 and 11 pct, respectively. These results suggest that to reduce defects caused by binder swelling during solvent debinding, alcohols with high solubility parameters can be added into heptane without sacrificing significantly on the debinding rate.

  1. Effect of pineapple waste powder on probiotic growth, antioxidant and antimutagenic activities of yogurt.

    PubMed

    Sah, B N P; Vasiljevic, T; McKechnie, S; Donkor, O N

    2016-03-01

    Although many fruit by-products are good sources of nutrients, little is known about their prebiotic potential. This research was aimed at establishing the prebiotic effect of pineapple wastes on probiotics including Lactobacillus (L.) acidophilus (ATCC® 4356™), L. casei (ATCC® 393™) and L. paracasei spp. paracasei (ATCC® BAA52™) and the subsequent release of antioxidant and antimutagenic peptides in yogurt during their growth. Oven- and freeze- dried peel and pomace were milled separately into powders and tested for prebiotic activities. The net probiotic growth (1.28-2.14 log cfu/g) in customized MRS broth containing the pineapple powders as a direct carbohydrate source was comparable to MRS broth containing glucose. The powders were also separately added to milk during the manufacturing of yogurt with or without probiotics. An increase (by 0.3-1.4 log cycle) in probiotic populations was observed in the yogurts as a consequence of pineapple powder supplementation. Crude water-soluble peptide extracts, prepared by high-speed centrifugation of the yogurts, displayed remarkable antioxidant activities assessed through in vitro assays, namely scavenging activity of 1,1-diphenyl-2-picrylhydrazyl radicals (IC50 = 0.37-0.19 mg/ml) and hydroxyl radicals (58.52-73.55 %). The peptide extracts also exhibited antimutagenic activities (18.60-32.72 %) as sodium azide inhibitor in the Salmonella mutagenicity test. Together, these results suggest that pineapple by-products exhibited prebiotic properties and could possibly be commercially applied in new functional food formulations. PMID:27570295

  2. Effect of pineapple waste powder on probiotic growth, antioxidant and antimutagenic activities of yogurt.

    PubMed

    Sah, B N P; Vasiljevic, T; McKechnie, S; Donkor, O N

    2016-03-01

    Although many fruit by-products are good sources of nutrients, little is known about their prebiotic potential. This research was aimed at establishing the prebiotic effect of pineapple wastes on probiotics including Lactobacillus (L.) acidophilus (ATCC® 4356™), L. casei (ATCC® 393™) and L. paracasei spp. paracasei (ATCC® BAA52™) and the subsequent release of antioxidant and antimutagenic peptides in yogurt during their growth. Oven- and freeze- dried peel and pomace were milled separately into powders and tested for prebiotic activities. The net probiotic growth (1.28-2.14 log cfu/g) in customized MRS broth containing the pineapple powders as a direct carbohydrate source was comparable to MRS broth containing glucose. The powders were also separately added to milk during the manufacturing of yogurt with or without probiotics. An increase (by 0.3-1.4 log cycle) in probiotic populations was observed in the yogurts as a consequence of pineapple powder supplementation. Crude water-soluble peptide extracts, prepared by high-speed centrifugation of the yogurts, displayed remarkable antioxidant activities assessed through in vitro assays, namely scavenging activity of 1,1-diphenyl-2-picrylhydrazyl radicals (IC50 = 0.37-0.19 mg/ml) and hydroxyl radicals (58.52-73.55 %). The peptide extracts also exhibited antimutagenic activities (18.60-32.72 %) as sodium azide inhibitor in the Salmonella mutagenicity test. Together, these results suggest that pineapple by-products exhibited prebiotic properties and could possibly be commercially applied in new functional food formulations.

  3. PERFORMANCE OF ACTIVATED SLUDGE-POWDERED ACTIVATED CARBON-WET AIR REGENERATION SYSTEMS

    EPA Science Inventory

    The investigation summarized in the report was undertaken to evaluate the performance of powdered activated carbon (PAC) technology used in conjunction with wet air regeneration (WAR) at municipal wastewater treatment plants. Excessive ash concentrations accumulated in the mixed ...

  4. In vitro bioactivity and antimicrobial tuning of bioactive glass nanoparticles added with neem (Azadirachta indica) leaf powder.

    PubMed

    Prabhu, M; Ruby Priscilla, S; Kavitha, K; Manivasakan, P; Rajendran, V; Kulandaivelu, P

    2014-01-01

    Silica and phosphate based bioactive glass nanoparticles (58SiO2-33CaO-9P2O5) with doping of neem (Azadirachta indica) leaf powder and silver nanoparticles were prepared and characterised. Bioactive glass nanoparticles were produced using sol-gel technique. In vitro bioactivity of the prepared samples was investigated using simulated body fluid. X-ray diffraction (XRD) pattern of prepared glass particles reveals amorphous phase and spherical morphology with a particle size of less than 50 nm. When compared to neem doped glass, better bioactivity was attained in silver doped glass through formation of hydroxyapatite layer on the surface, which was confirmed through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analysis. However, neem leaf powder doped bioactive glass nanoparticles show good antimicrobial activity against Staphylococcus aureus and Escherichia coli and less bioactivity compared with silver doped glass particles. In addition, the biocompatibility of the prepared nanocomposites reveals better results for neem doped and silver doped glasses at lower concentration. Therefore, neem doped bioactive glass may act as a potent antimicrobial agent for preventing microbial infection in tissue engineering applications.

  5. In Vitro Bioactivity and Antimicrobial Tuning of Bioactive Glass Nanoparticles Added with Neem (Azadirachta indica) Leaf Powder

    PubMed Central

    Prabhu, M.; Ruby Priscilla, S.; Kavitha, K.; Manivasakan, P.; Rajendran, V.; Kulandaivelu, P.

    2014-01-01

    Silica and phosphate based bioactive glass nanoparticles (58SiO2-33CaO-9P2O5) with doping of neem (Azadirachta indica) leaf powder and silver nanoparticles were prepared and characterised. Bioactive glass nanoparticles were produced using sol-gel technique. In vitro bioactivity of the prepared samples was investigated using simulated body fluid. X-ray diffraction (XRD) pattern of prepared glass particles reveals amorphous phase and spherical morphology with a particle size of less than 50 nm. When compared to neem doped glass, better bioactivity was attained in silver doped glass through formation of hydroxyapatite layer on the surface, which was confirmed through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analysis. However, neem leaf powder doped bioactive glass nanoparticles show good antimicrobial activity against Staphylococcus aureus and Escherichia coli and less bioactivity compared with silver doped glass particles. In addition, the biocompatibility of the prepared nanocomposites reveals better results for neem doped and silver doped glasses at lower concentration. Therefore, neem doped bioactive glass may act as a potent antimicrobial agent for preventing microbial infection in tissue engineering applications. PMID:25276834

  6. Record Methane Storage in Monolithic and Powdered Activated Carbons

    NASA Astrophysics Data System (ADS)

    Soo, Yuchoong; Nordwald, E.; Hester, B.; Romanos, J.; Isaacson, B.; Stalla, D.; Moore, D.; Kraus, M.; Burress, J.; Dohnke, E.; Pfeifer, P.

    2010-03-01

    The Alliance for Collaborative Research in Alternative Fuel Technology (ALL-CRAFT) has developed activated carbons from corn cob as adsorbent materials for methane gas storage by physisorption at low pressures. KOH activated carbons were compressed into carbon monolith using chemical binders. High pressure methane isotherms up to 250 bar at room temperature on monolithic and powdered activated carbons were measured gravimetrically and volumetrically. Record methane storage capacities of 250 g CH4/kg carbon and 130 g CH4/liter carbon at 35 bar and 293 K have been achieved. BET surface area, porosity, and pore size distributions were measured from sub-critical nitrogen isotherms. Pore entrances were characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). A prototype adsorbed natural gas (ANG) tank, loaded with carbon monoliths, was tested in Kansas City.

  7. Solar activity around AD 775 from aurorae and radiocarbon

    NASA Astrophysics Data System (ADS)

    Neuhäuser, R.; Neuhäuser, D. L.

    2015-04-01

    A large variation in 14C around AD 775 has been considered to be caused by one or more solar super-flares within one year. We critically review all known aurora reports from Europe as well as the Near, Middle, and Far East from AD 731 to 825 and find 39 likely true aurorae plus four more potential aurorae and 24 other reports about halos, meteors, thunderstorms etc., which were previously misinterpreted as aurorae or misdated; we assign probabilities for all events according to five aurora criteria. We find very likely true aurorae in AD 743, 745, 762, 765, 772, 773, 793, 796, 807, and 817. There were two aurorae in the early 770s observed near Amida (now Diyarbak\\i r in Turkey near the Turkish-Syrian border), which were not only red, but also green-yellow - being at a relatively low geomagnetic latitude, they indicate a relatively strong solar storm. However, it cannot be argued that those aurorae (geomagnetic latitude 43 to 50°, considering five different reconstructions of the geomagnetic pole) could be connected to one or more solar super-flares causing the 14C increase around AD 775: There are several reports about low- to mid-latitude aurorae at 32 to 44° geomagnetic latitude in China and Iraq; some of them were likely observed (quasi-)simultaneously in two of three areas (Europe, Byzantium/Arabia, East Asia), one lasted several nights, and some indicate a particularly strong geomagnetic storm (red colour and dynamics), namely in AD 745, 762, 793, 807, and 817 - always without 14C peaks. We use 39 likely true aurorae as well as historic reports about sunspots together with the radiocarbon content from tree rings to reconstruct the solar activity: From AD {˜ 733} to {˜ 823}, we see at least nine Schwabe cycles; instead of one of those cycles, there could be two short, weak cycles - reflecting the rapid increase to a high 14C level since AD 775, which lies at the end of a strong cycle. In order to show the end of the dearth of naked-eye sunspots, we

  8. A Guide to Microsoft Active Directory (AD) Design

    SciTech Connect

    Dias, J

    2002-04-29

    The goal of this paper is to facilitate the design process for those DOE sites that are currently engaged in designing their Active Directory (AD) network. It is a roadmap to enable analysis of the complicated design tradeoffs associated with Active Directory Design. By providing discussion of Active Directory design elements which are permanent and costly to change once deployed, the hope is to minimize the risks of sponsoring failed designs, or joining existing infrastructures not suitable to programmatic needs. Specifically, most Active Directory structures will fall under one of three common designs: Single Domain, Single Forest with Multiple Domains, or Multiple Forests. Each has benefits and concerns, depending on programmatic and organizational structures. The comparison of these three approaches will facilitate almost any Active Directory design effort. Finally, this paper describes some best practices to consider when designing Active Directory based on three years of research and experience.

  9. Effects of Properties on S45C Carbon Steel by Electroless NiP Adding Al2O3 Powder of Composite Deposition and Various Heat Treatments

    NASA Astrophysics Data System (ADS)

    Chang, Shih-Hsien; Liang, Cheng; Chang, Chih-Chung

    2014-06-01

    This research studies the effects on the surface microstructure and mechanical properties of S45C carbon steel via electroless Ni-P, by adding αAl2O3 powder via composite deposition and various heat treatments. The plating specimens were treated with pH5 and pH8 baths heated to 350°C and 300°C, respectively, and soaked for 1 hr. Meanwhile, two different particle sizes of Al2O3 powder were added to the electroless Ni-P plating: 0.3 μm of αAl2O3 and 0.05 μm of γAl2O3 powder, respectively. The experimental results show that, after 1 hr of heat treatment at 300°C, the optimal hardness for the specimens using the pH8 of Ni-P with αAl2O3 and γAl2O3 added by composite deposition are HV0.05 1237 and HV0.05 1145, respectively. All of the specimens underwent the main precipitate phase of Ni3P after heat treatment.

  10. Effect of calcium on adsorption capacity of powdered activated carbon.

    PubMed

    Li, Gang; Shang, Junteng; Wang, Ying; Li, Yansheng; Gao, Hong

    2013-12-01

    We investigated the effect of calcium ion on the adsorption of humic acid (HA) (as a target pollutant) by powered activated carbon. The HA adsorption isotherms at different pH and kinetics of two different solutions including HA alone and HA doped Ca(2+), were performed. It was showed that the adsorption capacity of powdered activated carbon (PAC) for HA was markedly enhanced when Ca(2+) was doped into HA. Also, HA and Ca(2+) taken as nitrate were tested on the uptake of each other respectively and it was showed that the adsorbed amounts of both of them were significantly promoted when HA and calcium co-existed. Furthermore, the adsorbed amount of HA slightly decreased with the increasing of Ca(2+) concentration, whereas the amount of calcium increased with the increasing of HA concentration, but all above the amounts without addition. Finally, the change of pH before and after adsorption process is studied. In the two different solutions including HA alone and HA doped Ca(2+), pH had a small rise, but the extent of pH of later solution was bigger. PMID:25078809

  11. Effect of powdered activated carbon on integrated submerged membrane bioreactor-nanofiltration process for wastewater reclamation.

    PubMed

    Woo, Yun Chul; Lee, Jeong Jun; Shim, Wang-Geun; Shon, Ho Kyong; Tijing, Leonard D; Yao, Minwei; Kim, Han-Seung

    2016-06-01

    The aim of this study was to determine the effect of powdered activated carbon (PAC) on the overall performance of a submerged membrane bioreactor (SMBR) system integrated with nanofiltration (NF) for wastewater reclamation. It was found that the trans-membrane pressure of SMBR increased continuously while that of the SMBR with PAC was more stable, mainly because water could still pass through the PACs and membrane even though foulants adhered on the PAC surface. The presence of PAC was able to mitigate fouling in SMBR as well as in NF. SMBR-NF with PAC obtained a higher flux of 8.1 LMH compared to that without PAC (6.6 LMH). In addition, better permeate quality was obtained with SMBR-NF integrated process added with PAC. The present results suggest that the addition of PAC in integrated SMBR-NF process could possibly lead to satisfying water quality and can be operated for a long-term duration.

  12. 76 FR 58533 - Powder River Regional Coal Team Activities; Notice of Public Meeting in Casper, WY

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-21

    ... Bureau of Land Management Powder River Regional Coal Team Activities; Notice of Public Meeting in Casper... River Regional Coal Team (RCT) has scheduled a public meeting for October 26, 2011, to review coal management activities in the Powder River Coal Production Region. DATES: The RCT meeting will begin at 9...

  13. Powdered Activated Carbon: An Alternative Approach to Genomic DNA Purification.

    PubMed

    Barbarić, Lucija; Bačić, Ivana; Grubić, Zorana

    2015-07-01

    Forensic evidence samples are routinely found as stains on various substrates, which may contain substances known to inhibit polymerase chain reaction (PCR). The goal of this study was to evaluate post-Chelex(®) 100 purification using powdered activated carbon (PAC). Mock crime scene DNA extracts were analyzed using quantitative PCR and short tandem repeat (STR) profiling to test the DNA recovery and inhibitor removal using PAC with those of the Amicon(®) Ultra 100K. For extracted bloodstains on soil and wood substrates, PAC and Amicon(®) Ultra 100K generated similar DNA yield and quality. Moreover, the two methods significantly decreased the concentration of humic substances and tannins compared to nonpurified extracts (p < 0.001). In instances where extracts contained indigo dye (bloodstains on denim), Amicon(®) Ultra 100K performed better than PAC due to improved amplifiability. Efficient adsorption of humic substances and tannins, which are common inhibitors, indicates PAC's potential application in the purification of high-template DNA extracts.

  14. Doped titanium dioxide nanocrystalline powders with high photocatalytic activity

    SciTech Connect

    Castro, A.L.; Jumas, J.-C.; Costa, F.M.

    2009-07-15

    Doped titanium dioxide nanopowders (M:TiO{sub 2}; M=Fe, Co, Nb, Sb) with anatase structure were successfully synthesized through an hydrothermal route preceded by a precipitation doping step. Structural and morphological characterizations were performed by powder XRD and TEM. Thermodynamic stability studies allowed to conclude that the anatase structure is highly stable for all doped TiO{sub 2} prepared compounds. The photocatalytic efficiency of the synthesized nanopowders was tested and the results showed an appreciable enhancement in the photoactivity of the Sb:TiO{sub 2} and Nb:TiO{sub 2}, whereas no photocatalytic activity was detected for the Fe:TiO{sub 2} and Co:TiO{sub 2} nanopowders. These results were correlated to the doping ions oxidation states, determined by Moessbauer spectroscopy and magnetization data. - Graphical abstract: Doped titanium dioxide nanopowders (M:TiO{sub 2}; M=Fe, Co, Nb, Sb) with highly stable anatase structure were successfully synthesized through an hydrothermal route. The photocatalytic efficiencies of the synthesized nanopowders were tested and the results show an appreciable enhancement in the photoactivity of the Sb:TiO{sub 2} and Nb:TiO{sub 2}.

  15. Powdered Activated Carbon: An Alternative Approach to Genomic DNA Purification.

    PubMed

    Barbarić, Lucija; Bačić, Ivana; Grubić, Zorana

    2015-07-01

    Forensic evidence samples are routinely found as stains on various substrates, which may contain substances known to inhibit polymerase chain reaction (PCR). The goal of this study was to evaluate post-Chelex(®) 100 purification using powdered activated carbon (PAC). Mock crime scene DNA extracts were analyzed using quantitative PCR and short tandem repeat (STR) profiling to test the DNA recovery and inhibitor removal using PAC with those of the Amicon(®) Ultra 100K. For extracted bloodstains on soil and wood substrates, PAC and Amicon(®) Ultra 100K generated similar DNA yield and quality. Moreover, the two methods significantly decreased the concentration of humic substances and tannins compared to nonpurified extracts (p < 0.001). In instances where extracts contained indigo dye (bloodstains on denim), Amicon(®) Ultra 100K performed better than PAC due to improved amplifiability. Efficient adsorption of humic substances and tannins, which are common inhibitors, indicates PAC's potential application in the purification of high-template DNA extracts. PMID:25929735

  16. Comparison of hydration, tyrosinase resistance, and antioxidant activation in three kinds of pearl powders.

    PubMed

    Shao, Dong-Zi; Wang, Cheng-Kun; Hwang, Hann-Jang; Hung, Ching-Hsia; Chen, Yu-Wen

    2010-01-01

    In recent years, people have bred freshwater pearls as a substitute for natural pearls that occur in seawater, and they have also developed water-soluble pearl powder (P-w) and ultra-micro (P-mu) and ultra-nano pearl powder (P-n) products. However, neither the scientific value of pearl powder, nor the differences in efficiencies of different pearl powder products is still unknown. In this study, the effectiveness of three kinds of pearl powder products in various applications was compared. Tests for transepidermal water loss (TEWL) and evaluations of the skin surface hydration of test subjects showed that pearl powder has a satisfactory moisturizing effect on skin and that P-mu has a distinctly stronger moisturizing effect than P-w. The three pearl powder products can also significantly reduce the activation of tyrosinase and free radicals. In tests for reducing power and 1,1-diphenyl-2-picrylhydrazyl (DPPH) for scavenging free radicals, P-n and P-mu showed better performance than P-w. These results provide a reliable scientific basis for the use of pearl powder in beauty treatment, resistance to aging, and clinical medical treatment. PMID:20447365

  17. Combination of powdered activated carbon and powdered zeolite for enhancing ammonium removal in micro-polluted raw water.

    PubMed

    Liao, Zhen-Liang; Chen, Hao; Zhu, Bai-Rong; Li, Huai-Zheng

    2015-09-01

    Even zeolite is promising in ammonia pollution disposing, its removal efficiency is frequently interfered by organics. As activated carbon has good removal efficiency on organic contaminants, combination of two adsorbents may allow their respective adsorption characteristics into full play. This paper provides a performance assessment of the combination for enhancing ammonium removal in micro-polluted raw water. Gel-filtration chromatography (GFC) was carried out to quantify the molecular weight (MW) range of organic contaminants that powdered activated carbon (PAC) and powdered zeolite (PZ) can remove. The polydispersity difference which also calculated from GFC may indicate the wider organic contaminants removal range of PAC and the relatively centralized removal range of PZ. The jar tests of combination dosing confirm a synergistic effect which promotes ammonium removing. Nevertheless, it also shows an antagonism hindering the due removal performance of the two adsorbents on CODMn, while it is not much evident on UV254. Furthermore, a comparison study with simulated coagulation-sedimentation process was conducted to evaluate the optimum dosing points (spatial and temporal) of PAC and PZ among follows: suction well, pipeline mixer, early and middle phase of flocculation. We suggest to dose both two adsorbents into the early phase of flocculation to maximize the versatile removal efficiency on turbidity, ammonium and organic contaminants.

  18. Combination of powdered activated carbon and powdered zeolite for enhancing ammonium removal in micro-polluted raw water.

    PubMed

    Liao, Zhen-Liang; Chen, Hao; Zhu, Bai-Rong; Li, Huai-Zheng

    2015-09-01

    Even zeolite is promising in ammonia pollution disposing, its removal efficiency is frequently interfered by organics. As activated carbon has good removal efficiency on organic contaminants, combination of two adsorbents may allow their respective adsorption characteristics into full play. This paper provides a performance assessment of the combination for enhancing ammonium removal in micro-polluted raw water. Gel-filtration chromatography (GFC) was carried out to quantify the molecular weight (MW) range of organic contaminants that powdered activated carbon (PAC) and powdered zeolite (PZ) can remove. The polydispersity difference which also calculated from GFC may indicate the wider organic contaminants removal range of PAC and the relatively centralized removal range of PZ. The jar tests of combination dosing confirm a synergistic effect which promotes ammonium removing. Nevertheless, it also shows an antagonism hindering the due removal performance of the two adsorbents on CODMn, while it is not much evident on UV254. Furthermore, a comparison study with simulated coagulation-sedimentation process was conducted to evaluate the optimum dosing points (spatial and temporal) of PAC and PZ among follows: suction well, pipeline mixer, early and middle phase of flocculation. We suggest to dose both two adsorbents into the early phase of flocculation to maximize the versatile removal efficiency on turbidity, ammonium and organic contaminants. PMID:25929873

  19. Gastrocnemius and soleus are selectively activated when adding knee extensor activity to plantar flexion.

    PubMed

    Suzuki, Takahito; Chino, Kentaro; Fukashiro, Senshi

    2014-08-01

    The gastrocnemius is a biarticular muscle that acts not only as a plantar flexor, but also as a knee flexor, meaning that it is an antagonist during knee extension. In contrast, the soleus is a monoarticular plantar flexor. Based on this anatomical difference, these muscles' activities should be selectively activated during simultaneous plantar flexion and knee extension, which occur during many activities of daily living. This study examined the selective activation of gastrocnemius and soleus activities when voluntary isometric activation of knee extensors was added to voluntary isometric plantar flexion. Ten male volunteers performed isometric plantar flexion at 10%, 20%, and 30% of maximum effort. During each plantar flexion task, isometric knee extension was added at 0%, 50%, and 100% of maximum effort. When knee extension was added, the average rectified value of the electromyographic activity of the medial gastrocnemius was significantly depressed (P=.002), whereas that of the soleus was significantly increased (P<.001) regardless of the plantar flexion level. These results suggest that plantar flexion with concurrent knee extensor activity leads to selective activation of the soleus and depression of the synergistic activity of the gastrocnemius.

  20. Characterization of the distribution of the sintering activator boron in powder metallurgical steels with SIMS.

    PubMed

    Krecar, Dragan; Vassileva, Vassilka; Danninger, Herbert; Hutter, Herbert

    2004-06-01

    Powder metallurgy is a well-established method for manufacturing ferrous precision parts. A very important step is sintering, which can be strongly enhanced by the formation of a liquid phase during the sintering process. Boron activates this process by forming such a liquid phase at about 1200 degrees C. In this work, the sintering of Fe-B was performed under the protective atmospheres of hydrogen, argon or nitrogen. Using different grain sizes of the added ferroboron leads to different formations of pores and to the formation of secondary pores. The effect of boron was investigated by means of Secondary Ion Mass Spectrometry (SIMS) supported by Scanning Electron Microscopy (SEM) and Light Microscopy (LM). To verify the influence of the process parameters on the mechanical properties, the microstructure (pore shape) was examined and impact energy measurements were performed. The concentrations of B in different samples were varied from 0.03-0.6 weight percent (wt%). Higher boron concentrations are detectable by EPMA, whereas the distributions of boron in the samples with interesting overall concentration in the low wt% range are only detectable by means of SIMS. This work shows that the distribution of boron strongly depends on its concentration and the sintering atmosphere used. At low concentration (up to 0.1 wt%) there are boride precipitations; at higher concentration there is a eutectic iron-boron grain boundary network. There is a decrease of the impact energy observed that correlates with the amount of eutectic phase.

  1. [Effect of powdered activated carbon on the sludge mixed liquor characteristics and membrane fouling of MBR].

    PubMed

    Li, Shao-Feng; Gao, Yuan

    2011-02-01

    Effect of dosing powder activated carbon (PAC) on the characteristics of the sludge mixed liquor in membrane bioreactor (MBR) was investigated by parallel tests. And the reason that PAC mitigated membrane fouling was also explored. The results showed that PAC could decrease mixture viscosity and increase sludge particle size, which led to less trans-membrane pressure developing. Extracellular polymer substances (EPS) content, sludge specific resistance and cake layer resistance (R(c)) had a good correlation. Adding PAC could decrease EPS concentration, sludge specific resistance and then slow down the increase of R(c), which mitigated membrane fouling. Membrane pore blocking resistance (R(p)) increased exponentially with increasing of the soluble microbial products (SMP) concentration in the supernatant. Dosing PAC reduced the SMP concentration and slowed down the growth rate of R(p), which was helpful to mitigating membrane fouling. R(c) and R(p) increased along with the operation of MBRs and R(c)/R(f) (26.32% -63.16%) was always greater than R(p)/R(f) (7.89% -35.32%) which suggested the R(c) was the main factor in membrane fouling. Moreover, it was also found that controlling of dosing PAC on R(c) was better than it on R(p). PMID:21528575

  2. Comparing graphene, carbon nanotubes, and superfine powdered activated carbon as adsorptive coating materials for microfiltration membranes.

    PubMed

    Ellerie, Jaclyn R; Apul, Onur G; Karanfil, Tanju; Ladner, David A

    2013-10-15

    Multi-walled carbon nanotubes (MWCNTs), nano-graphene platelets (NGPs), and superfine powdered activated carbon (S-PAC) were comparatively evaluated for their applicability as adsorptive coatings on microfiltration membranes. The objective was to determine which materials were capable of contaminant removal while causing minimal flux reduction. Methylene blue and atrazine were the model contaminants. When applied as membrane coatings, MWCNTs had minimal retention capabilities for the model contaminants, and S-PAC had the fastest removal. The membrane coating approach was also compared with a stirred vessel configuration, in which the adsorbent was added to a stirred flask preceding the membrane cell. Direct application of the adsorbent to the membrane constituted a greater initial reduction in permeate concentrations of the model contaminants than with the stirred flask setup. All adsorbents except S-PAC showed flux reductions less than 5% after application as thin-layer membrane coatings, and flux recovery after membrane backwashing was greater than 90% for all materials and masses tested. PMID:23911830

  3. Effect of powdered activated carbon on integrated submerged membrane bioreactor-nanofiltration process for wastewater reclamation.

    PubMed

    Woo, Yun Chul; Lee, Jeong Jun; Shim, Wang-Geun; Shon, Ho Kyong; Tijing, Leonard D; Yao, Minwei; Kim, Han-Seung

    2016-06-01

    The aim of this study was to determine the effect of powdered activated carbon (PAC) on the overall performance of a submerged membrane bioreactor (SMBR) system integrated with nanofiltration (NF) for wastewater reclamation. It was found that the trans-membrane pressure of SMBR increased continuously while that of the SMBR with PAC was more stable, mainly because water could still pass through the PACs and membrane even though foulants adhered on the PAC surface. The presence of PAC was able to mitigate fouling in SMBR as well as in NF. SMBR-NF with PAC obtained a higher flux of 8.1 LMH compared to that without PAC (6.6 LMH). In addition, better permeate quality was obtained with SMBR-NF integrated process added with PAC. The present results suggest that the addition of PAC in integrated SMBR-NF process could possibly lead to satisfying water quality and can be operated for a long-term duration. PMID:26879205

  4. Influence of pulsed mechanical activation of hematite-graphite-aluminum powder mixtures on the reduction of iron oxides

    NASA Astrophysics Data System (ADS)

    Bodrova, L. E.; Vatolin, N. A.; Pastukhov, E. A.; Petrova, S. A.; Popova, E. A.; Zakharov, R. G.

    2011-11-01

    To decrease the temperature of direct iron reduction by carbon and aluminum, short-term pulsed mechanical activation (PMA) of an Fe2O3 + Cgr + Al powder mixture is perfumed during sound-frequency shock loading by a flat activating plunger. The PMA efficiency for powders in comparable with mechanical activation in high-energy ball mills in a decrease in the activation time and retaining the chemical purity of a powder composition.

  5. Synthesis of In-situ Aluminum Matrix Composite Using a New Activated Powder Injection Method

    NASA Astrophysics Data System (ADS)

    Maleki, A.; Meratian, M.; Niroumand, B.; Gupta, M.

    2008-12-01

    In the present study, in-situ Al matrix composites containing alumina particles were synthesized by a new method that involved injection of an activated powder mixture into the molten aluminum, which was subsequently squeeze cast to minimize its porosity. The activated powder mixture was prepared by milling of powders of commercially pure aluminum and zinc oxide for a predetermined time. Milling for 60 minutes led to optimum activation of the reactant powders. Such activation reduced the reaction temperature from above 1000 °C to about 640 °C. Microstructural characterization studies revealed the formation of submicron size alumina particles with near equiaxed morphology and good particle/matrix interface. The composite specimen synthesized using the activated powder injection (API) method exhibited higher hardness, greater yield and tensile strengths, and lower elongation when compared to the monolithic specimen of similar composition. This article places particular emphasis on explaining the uniqueness of the processing methodology used in this study for synthesis of in-situ Al/Al2O3 composites.

  6. Microstructural and electrical changes in nickel manganite powder induced by mechanical activation

    SciTech Connect

    Savic, S.M.; Mancic, L.; Stojanovic, G.; Brankovic, Z.; Aleksic, O.S.; Brankovic, G.

    2011-07-15

    Highlights: {yields} The influence of mechanical activation on microstructure evolution in the nickel manganite powder was investigated as well as electrical properties of the sintered samples. {yields} Structural refinement obtained by Topas-Academic software based on Rietveld analysis showed that the milling process remarkably changed the powder morphology and microstructure. {yields} SEM studies of sintered samples also revealed the strong influence of milling time on ceramics density (increases with milling time). {yields} The electrical properties of ceramic samples are clearly conditioned by terms of synthesis, in our case the time of mechanical activation. {yields} The highest density and higher values of dielectric constant were achieved at the sample activated for 45 min. -- Abstract: Nickel manganite powder synthesized by calcination of a stoichiometric mixture of manganese and nickel oxide was additionally mechanically activated in a high energy planetary ball mill for 5-60 min in order to obtain a pure NiMn{sub 2}O{sub 4} phase. The as-prepared powders were uniaxially pressed into disc shape pellets and then sintered for 60 min at 1200 {sup o}C. Changes in the particle morphology induced by mechanical activation were monitored using scanning electron microscopy, while changes in powder structural characteristics were followed using X-ray powder diffraction. The ac impedance spectroscopy was performed on sintered nickel manganite samples at 25 {sup o}C, 50 {sup o}C and 80 {sup o}C. It was shown that mechanical activation intensifies transport processes causing a decrease in the average crystallites size, while longer activation times can lead to the formation of aggregates, defects and increase of lattice microstrains. The observed changes in microstructures were correlated with measured electrical properties in order to define optimal processing conditions.

  7. The effect of mechanical activation on the heat capacity of powdered tungsten

    NASA Astrophysics Data System (ADS)

    Malkin, A. I.; Kiselev, M. R.; Klyuev, V. A.; Loznetsova, N. N.; Toporov, Yu. P.

    2012-06-01

    We have studied the heat capacity ( C p ) of a mechanically activated tungsten powder. It is established that the mechanical processing leads to an increase in C p of the metal powder at low temperatures and modifies the character of the temperature dependence of this parameter. The dependences of C p and its heating-induced variation on the treatment duration have been determined. It is concluded that the observed effects are related to the accumulation of defects in the metal grain volume during mechanical activation and their annealing in the course of heating.

  8. Livestock Air Treatment Using PVA-Coated Powdered Activated Carbon Biofilter

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Ideal biofilter media provide surface for attachment of microorganisms responsible for removing air-born contaminants while facilitating passage of air. This study evaluated the efficacy of polyvinyl alcohol (PVA)-coated powdered activated carbon particles as a biofiltration medium. This material e...

  9. Livestock air treatment using PVA-coated powdered activated carbon biofilter

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The efficacy of polyvinyl alcohol (PVA) biofilters was studied using bench-scale biofilters and air from aerobically-treated swine manure. The PVA-coated powdered activated carbon particles showed excellent properties as a biofiltration medium: water holding capacity of 1.39 g H2O/g-dry PVA; wet por...

  10. Gentamicin and leucine inhalable powder: what about antipseudomonal activity and permeation through cystic fibrosis mucus?

    PubMed

    Russo, Paola; Stigliani, Mariateresa; Prota, Lucia; Auriemma, Giulia; Crescenzi, Carlo; Porta, Amalia; Aquino, Rita P

    2013-01-20

    The aim of this study was to evaluate the permeation properties of gentamicin (G) in a novel dry powder form for inhalation through an artificial mucus model. Moreover, since respiratory infections sustained by Pseudomonas are a major cause of sickness and death in CF patients, the susceptibility of P. aeruginosa to engineered G powders was investigated. Micronized G and G/leucine (85:15) formulations were produced by co-spray-drying, using process parameters and conditions previously set. Powders were characterized in terms of yield, drug content and aerodynamic profiles, analyzed by Andersen Cascade Impactor. Different mucus models were prepared, showing composition and viscosity similar to those of the native CF mucus. To investigate the impact on drug permeation, Franz-type vertical diffusion cells were used; the powders were applied directly on a synthetic membrane with or without the interposition of the artificial mucus layer. In buffer, gentamicin showed a diffusion controlled release; the presence of leucine reduced powder wettability and, consequently, the permeation rate. Otherwise, mucus delayed drug permeation from both G and G/leucine formulations, with a faint influence of the aminoacid. Antimicrobial tests revealed that G/leu engineered particles are able to preserve the antipseudomonal activity, even in presence of the mucus.

  11. Egg quality and productive performance of laying hens fed different levels of skimmed milk powder added to a diet containing Lactobacillus acidophilus.

    PubMed

    Cesari, V; Mangiagalli, M G; Giardini, A; Galimberti, P; Carteri, S; Gallazzi, D; Toschi, I

    2014-05-01

    The current trial was carried out on a commercial poultry farm to study the effect of skim milk powder (SMP) added to a diet containing Lactobacillus acidophilus on performance and egg quality of laying hens from 20 to 49 wk of age. A total of 2,400 Hy-Line W-36 laying hens were housed in 600 unenriched cages (4 hens each) located over 4 tier levels. Animals were assigned to 1 of 3 experimental treatments (0, 3, and 4). The laying hens assigned to treatments 3 and 4 received a diet enriched respectively with 3 and 4% SMP, whereas the animals in treatment 0 were fed a diet without SMP. All diets, moreover, were supplemented with L. acidophilus D2/CSL. Hen performance was determined throughout the experimental period and egg quality was measured on 30 eggs per treatment every week. Results showed that productive performance in terms of egg production, egg weight, and feed conversion ratio was not influenced by SMP at 3 or 4% of the diet. Egg quality was significantly affected by SMP included at 3 or 4% of the diet. Eggs from treatments 3 and 4, in fact, displayed higher shell thickness than those from treatment 0 (P < 0.0001). Likewise, specific gravity, Haugh unit, and shell percentage were significantly affected by the addition of SMP. In conclusion, in our study, SMP added to a diet containing L. acidophilus had no significant effects on the productive parameters of hens during the laying period, whereas significant improvements were found in certain egg quality characteristics. PMID:24795312

  12. Egg quality and productive performance of laying hens fed different levels of skimmed milk powder added to a diet containing Lactobacillus acidophilus.

    PubMed

    Cesari, V; Mangiagalli, M G; Giardini, A; Galimberti, P; Carteri, S; Gallazzi, D; Toschi, I

    2014-05-01

    The current trial was carried out on a commercial poultry farm to study the effect of skim milk powder (SMP) added to a diet containing Lactobacillus acidophilus on performance and egg quality of laying hens from 20 to 49 wk of age. A total of 2,400 Hy-Line W-36 laying hens were housed in 600 unenriched cages (4 hens each) located over 4 tier levels. Animals were assigned to 1 of 3 experimental treatments (0, 3, and 4). The laying hens assigned to treatments 3 and 4 received a diet enriched respectively with 3 and 4% SMP, whereas the animals in treatment 0 were fed a diet without SMP. All diets, moreover, were supplemented with L. acidophilus D2/CSL. Hen performance was determined throughout the experimental period and egg quality was measured on 30 eggs per treatment every week. Results showed that productive performance in terms of egg production, egg weight, and feed conversion ratio was not influenced by SMP at 3 or 4% of the diet. Egg quality was significantly affected by SMP included at 3 or 4% of the diet. Eggs from treatments 3 and 4, in fact, displayed higher shell thickness than those from treatment 0 (P < 0.0001). Likewise, specific gravity, Haugh unit, and shell percentage were significantly affected by the addition of SMP. In conclusion, in our study, SMP added to a diet containing L. acidophilus had no significant effects on the productive parameters of hens during the laying period, whereas significant improvements were found in certain egg quality characteristics.

  13. Guarana powder polysaccharides: characterisation and evaluation of the antioxidant activity of a pectic fraction.

    PubMed

    Dalonso, Nicole; Petkowicz, Carmen Lúcia de Oliveira

    2012-10-15

    Guarana is a fruit from the Amazon whose seeds are used to produce guarana powder. Guarana powder is consumed by the population mainly for its stimulant activity. It has been shown that guarana seeds contain low-molar-mass compounds; however, no data have been reported concerning the polysaccharides. In this work, the polysaccharides present in guarana powder were investigated. A pectic fraction and a xylan were isolated and characterised. Antioxidant activity tests were performed with a methanolic extract and the pectic fraction at concentrations of 0.1-10 mg/ml. The methanolic extract exhibited a strong capacity for scavenging DPPH radicals (90.9% at 10 mg/ml). At the same concentration, the polysaccharide showed a DPPH(·)-scavenging activity of 68.4%. At a higher concentration, the methanolic extract and the polysaccharide exhibited similar hydroxyl radical-scavenging effects (~70%). The results suggest that the polysaccharides present in guarana can contribute to the possible biological effects of guarana powder. PMID:23442624

  14. Guarana powder polysaccharides: characterisation and evaluation of the antioxidant activity of a pectic fraction.

    PubMed

    Dalonso, Nicole; Petkowicz, Carmen Lúcia de Oliveira

    2012-10-15

    Guarana is a fruit from the Amazon whose seeds are used to produce guarana powder. Guarana powder is consumed by the population mainly for its stimulant activity. It has been shown that guarana seeds contain low-molar-mass compounds; however, no data have been reported concerning the polysaccharides. In this work, the polysaccharides present in guarana powder were investigated. A pectic fraction and a xylan were isolated and characterised. Antioxidant activity tests were performed with a methanolic extract and the pectic fraction at concentrations of 0.1-10 mg/ml. The methanolic extract exhibited a strong capacity for scavenging DPPH radicals (90.9% at 10 mg/ml). At the same concentration, the polysaccharide showed a DPPH(·)-scavenging activity of 68.4%. At a higher concentration, the methanolic extract and the polysaccharide exhibited similar hydroxyl radical-scavenging effects (~70%). The results suggest that the polysaccharides present in guarana can contribute to the possible biological effects of guarana powder.

  15. Efficacy of Sweet Potato Powder and Added Water as Fat Replacer on the Quality Attributes of Low-fat Pork Patties

    PubMed Central

    Verma, Akhilesh K.; Chatli, Manish Kumar; Kumar, Devendra; Kumar, Pavan; Mehta, Nitin

    2015-01-01

    The present study was conducted to investigate the efficacy of sweet potato powder (SPP) and water as a fat replacer in low-fat pork patties. Low-fat pork patties were developed by replacing the added fat with combinations of SPP and chilled water. Three different levels of SPP/chilled water viz. 0.5/9.5% (T-1), 1.0/9.0% (T-2), and 1.5/8.5% (T-3) were compared with a control containing 10% animal fat. The quality of low-fat pork patties was evaluated for physico-chemical (pH, emulsion stability, cooking yield, aw), proximate, instrumental colour and textural profile, and sensory attributes. The cooking yield and emulsion stability improved (p<0.05) in all treatments over the control and were highest in T-2. Instrumental texture profile attributes and hardness decreased, whereas cohesiveness increased compared with control, irrespective of SPP level. Dimensional parameters (% gain in height and % decrease in diameter) were better maintained during cooking in the low-fat product than control. The sensory quality attributes juiciness, texture and overall acceptability of T-2 and T-3 were (p<0.05) higher than control. Results concluded that low-fat pork patties with acceptable sensory attributes, improved cooking yield and textural attributes can be successfully developed with the incorporation of a combination of 1.0% SPP and 9.0% chilled water. PMID:25557822

  16. Comparison of Antioxidant Activities of Hydrolysates of Domestic and Imported Skim Milk Powders Treated with Papain

    PubMed Central

    Ha, Go Eun; Chang, Oun Ki; Han, Gi Sung; Ham, Jun Sang; Park, Beom-Young; Jeong, Seok-Geun

    2015-01-01

    Milk proteins have many potential sequences within their primary structure, each with a specific biological activity. In this study, we compared and investigated the bioactivities of hydrolysates of the domestic (A, B) and imported (C, D) skim milk powders generated using papain digestion. MALDI-TOF analysis revealed that all milk powder proteins were intact, indicating no autolysis. Electrophoretic analysis of hydrolysates showed papain treatment caused degradation of milk proteins into peptides of various size. The antioxidant activity of the hydrolysates, determined using 2,2-azino-bis-(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) and total phenolic contents (TPC) assays, increased with incubation times. In all skim milk powders, the antioxidant activities of hydrolysates were highest following 24 h papain treatment (TPC: A, 196.48 μM GE/L; B, 194.52 μM GE/L; C, 194.76 μM GE/L; D, 163.75 μM GE/L; ABTS: A, 75%; B, 72%; C, 72%; D, 57%). The number of peptide derived from skim milk powders, as determined by LC-MS/MS, was 308 for A, 283 for B, 208 for C, and 135 for D. Hydrolysate A had the highest antioxidant activity and the most potential antioxidant peptides amongst the four skim milk powder hydrolysates. A total of 4 β-lactoglobulin, 4 αs1-casein, and 56 β-casein peptide fragments were identified as potential antioxidant peptides in hydrolysate A by LC-MS/MS. These results suggest that domestic skim milk could have applications in various industries, i.e., in the development of functional foods. PMID:26761850

  17. Adding two active silver atoms on Au₂₅ nanoparticle.

    PubMed

    Yao, Chuanhao; Chen, Jishi; Li, Man-Bo; Liu, Liren; Yang, Jinlong; Wu, Zhikun

    2015-02-11

    Alloy nanoparticles with atomic monodispersity is of importance for some fundamental research (e.g., the investigation of active sites). However, the controlled preparation of alloy nanoparticles with atomic monodispersity has long been a major challenge. Herein, for the first time a unique method, antigalvanic reduction (AGR), is introduced to synthesize atomically monodisperse Au25Ag2(SC2H4Ph)18 in high yield (89%) within 2 min. Interestingly, the two silver atoms in Au25Ag2(SC2H4Ph)18 do not replace the gold atoms in the precursor particle Au25(SC2H4Ph)18 but collocate on Au25, which was supported by experimental and calculated results. Also, the two silver atoms are active to play roles in stabilizing the alloy nanoparticle, triggering the nanoparticle fluorescence and catalyzing the hydrolysis of 1,3-diphenylprop-2-ynyl acetate. PMID:25580617

  18. Review of the powder and decoction formulae in Traditional Chinese Medicine based on pharmacologically active substances and clinical evidence.

    PubMed

    Liu, Qihua; Wen, Jin; Peng, Zhiping; Liu, Fenglin; Tong, Xiaolin

    2015-06-01

    Powder formulae are an indispensable part of prescription in Traditional Chinese Medicine. Powder formulae are. characterized by good therapeutic efficacy and low dose used for their preparation. Analysis of the therapeutic application and material basis of pharmacological active substance in power formulae can enable the development of new powder formulae. This in turn can contribute to reduction of wastage of drug material, relief of shortage of herbal medicinal resources and sustainable development of Traditional Chinese Medicine.

  19. The effects of increasing amounts of milk replacer powder added to whole milk on feed intake and performance in dairy heifers.

    PubMed

    Azevedo, R A; Machado, F S; Campos, M M; Furini, P M; Rufino, S R A; Pereira, L G R; Tomich, T R; Coelho, S G

    2016-10-01

    The aim of this study was to evaluate the effects on feed intake, heifer performance, and health of increasing the total solids (TS) content of liquid feed (whole milk) by adding increasing amounts of milk replacer powder during the pre- and postweaning periods. Crossbred Holstein-Gyr heifers (n=60) were assigned to 1 of 4 treatments (n=15 per group), which consisted of different TS concentrations: 12.5, 15.0, 17.5, and 20.0% of liquid feed. Heifers received 6 L of liquid feed per day, divided into 2 equal meals (0800 and 1600h) and provided in buckets, from 5 to 55d of age. From 56 to 59d of age, the total amount of liquid feed was reduced by half, maintaining only morning feedings. Heifers were weaned at 60d and monitored until 90d of age. Water and starter were provided ad libitum during the entire experiment. Corn silage was included in the diet during the postweaning period (70d of age). Feed intake and health scores were evaluated daily. Body weight and body frame development were recorded weekly. Starting at 14d, ruminal pH was measured every other week. Laboratory analysis determined that the actual TS contents of the liquid feed were 13.5, 16.1, 18.2, and 20.4%, for the proposed 12.5, 15.0, 17.5, and 20.0% TS treatments, respectively. The osmolality of liquid feed treatments was 265 to 533mOsm/L. Intake of liquid feed was similar among treatments from 4wk of age. During the preweaning period, starter intake, fecal score, and days with diarrhea were similar among treatments. Ruminal pH at weaning averaged 6.2 and was similar among treatments. Increasing concentrations of TS in the liquid feed were associated with linear increases in average daily gain, final body weight, and growth performance, but linear decreases in feed efficiency. During the postweaning period, intake of starter, corn silage, and water were similar among treatments, as well as average daily gain and feed efficiency. Final body weight and growth performance during the postweaning period

  20. Effect of mechanical activation on the characteristics of ruthenium and aluminum powder mixtures

    NASA Astrophysics Data System (ADS)

    Povarova, K. B.; Morozov, A. E.; Skachkov, O. A.; Drozdov, A. A.; Kazanskaya, N. K.; Korenovskii, N. L.; D'Yakonova, N. B.

    2008-06-01

    The effect of treatment in a high-energy mill-attritor on the structure of RuAl-based alloy powder mixtures and the exothermic effects in them is studied. The mechanical activation (MA) of aluminum and ruthenium powder mixtures is found to mill the conglomerates of hard disperse (0.5-2 μm) ruthenium particles in the initial mixtures and to produce composite granules. These granules consist of hard disperse ruthenium particles connected by plastic fcc aluminum particles. The structure of these granules differs from that of the layered granules that form during the MA of powder mixtures of two plastic fcc metals (nickel, aluminum). The cold working of the hard ruthenium particles, which have the hcp lattice and are deformed via twinning, occurs due to a decrease in the coherent domain size (to 120-80 nm) rather than to an increase in the dislocation density (as in the case of the MA of Ni-Al powders). Every granule contains all alloy (composite) components, including disperse or nanosize oxide particles, bound to the components that form an intermetallic matrix during reaction sintering. In granules of both types, MA increases the contact area between both metals entering into the reaction of RuAl (NiAl) formation and sharply decreases the diffusion path length of Al in Ru (Ni). This results in a decrease in the temperature of the onset of reaction alloy formation, which begins now in a solid phase, and in a decrease in the exothermic effect of the monoaluminide formation with the participation of a liquid phase (Al). MA for 15-16 h of powder mixtures provides a microuniform distribution of base and alloying elements and phases in the deformable alloys with an intermetallic matrix that are produced by reaction sintering.

  1. Hypoglycemic activities of lyophilized powder of Gynura divaricata by improving antioxidant potential and insulin signaling in type 2 diabetic mice

    PubMed Central

    Xu, Bing-Qing; Yang, Ping; Zhang, Yu-Qing

    2015-01-01

    Background Diabetes mellitus is a serious disease affecting about 5% of people worldwide. Although several studies have indicated hypoglycemic activities of Gynura divaricata (GD), the mechanisms by which GD improves the symptoms of diabetes remain unclear. Objective The aim of this study was to investigate the potential hypoglycemic effects of GD. Design The leaves and stems of GD were prepared and lyophilized into a powder, which was added to the diet of mice with type 2 diabetes induced by a high-fat diet in combination with streptozotocin for 4 weeks. During this period, fasting blood glucose (FBG) levels and body weight of mice were measured. In addition, at the end of the experiment, a series of assays was performed. Results GD administration effectively alleviates insulin resistance and induces a decrease in FBG by 59.54% in 1.2% (L) GD-treated diabetic group and 56.13% in 4.8% (H) GD-treated diabetic group after 4 weeks, respectively, relative to diabetic model mice. The antioxidant capacity was improved by increasing the activities of glutathione peroxidase (GSH-Px) and total superoxide dismutase (T-SOD) by 64.87% and 53.42% in treatment group H, compared to diabetic model mice, while GD treatment induced a significant decrease in malondialdehyde (MDA) level by 50% in treatment group L, compared to the level in diabetic model mice. Furthermore, glucose metabolism was ameliorated by the increased glycogen synthesis in the livers of diabetic mice. In addition, we also demonstrated that the messenger RNA (mRNA) and protein expression levels of AKT, PI3K and PDK-1, which are involved in insulin signaling, were significantly increased. Conclusions Oral administration of the GD-lyophilized powder has been effectively hypoglycemic, which is done by activating insulin signaling and improving antioxidant capacity in mice with type 2 diabetes. PMID:26715102

  2. Removal of micro pollutants using activated biochars and powdered activated carbon in water

    NASA Astrophysics Data System (ADS)

    Kim, E.; Jung, C.; Han, J.; Son, A.; Yoon, Y.

    2015-12-01

    Recent studies have suggested that emerging micropollutants containing endocrine disrupting compounds (EDCs); bisphenol A, 17 α-ethinylestradiol, 17 β-estradiol and pharmaceuticals and personal care products (PPCPs); sulfamethoxazole, carbamazepine, ibuprofen, atenolol, benzophenone, benzotriazole, caffeine, gemfibrozil, primidone, triclocarban in water have been linked to ecological impacts, even at trace concentrations (sub ug/L). Adsorption with adsorbent such as activated carbon having a high-binding affinity has been widely used to eliminate various contaminants in the aqueous phase. Recently, an efficient treatment strategy for EDCs and PPCPs has been considered by using cost effective adsorption particularly with biochar in aqueous environmentIn this study, the objective of this study is to determine the removal of 13 target EDCs/PPCPs having different physicochemical properties by a biochar at various water quality conditions (pH (3.5, 7, and 10.5), background ions (NaCl, CaCl2, Na₂SO₄), ionic strength, natural organic matter (NOM)). The activated biochar produced in a laboratory was also characterized by using conventional analytical methods as well as advanced solid-state nuclear magnetic resonance (NMR) techniques, which answer how these properties determine the competitive adsorption characteristics and mechanisms of EDCs and PPCPs.The primary findings suggest that micropollutants can be removed more effectively by the biochar than the commercially available powdered activated carbon. At pH values below the pKa of each compound, the adsorption affinity toward adsorbents increased significantly with the pH, whereas the adsorption affinity decreased significantly at the pH above the pKa values. Na+ did not significantly impact adsorption, while increasing the concentration of Ca2+lead to increase in the adsorption of these micropollutants. NOM adsorption with humic acids on these adsorbents disturbed adsorption capacity of the target compounds as

  3. Phenolic Profiles and Contribution of Individual Compounds to Antioxidant Activity of Apple Powders.

    PubMed

    Raudone, Lina; Raudonis, Raimondas; Liaudanskas, Mindaugas; Viskelis, Jonas; Pukalskas, Audrius; Janulis, Valdimaras

    2016-05-01

    Apples (Malus domestica L.) are the most common source of phenolic compounds in northern European diet. Besides pectins, dietary fibers, vitamins, and oligosaccharides they contain phenolic compounds of different classes. Apple powders are convenient functional forms retaining significant amounts of phenolic antioxidants. In this study reducing and radical scavenging profiles of freeze-dried powders of "Aldas,ˮ "Auksis,ˮ "Connel Red,ˮ "Ligol,ˮ "Lodel,ˮ and "Rajkaˮ were determined and phenolic constituents were identified using ultra high-performance liquid chromatography coupled to quadrupole and time-of-flight mass spectrometers. A negative ionization mode was applied and seventeen compounds: phenolic acids (coumaroylquinic, chlorogenic), flavonoids (quercetin derivatives), and procyanidin derivatives (B1, B2, and C1) were identified in all tested apple samples. Total values of Trolox equivalents varied from 7.72 ± 0.32 up to 20.02 ± 0.52 and from 11.10 ± 0.57 up to 21.42 ± 0.75 μmol/g of dry weight of apple powder in FRAP (ferric reducing antioxidant power) and ABTS (2,2-azinobis-(3-ethylbenzothiazoline-6-sulfonic acid) postcolumn assays, respectively. The greatest Trolox equivalent values were determined for apples of "Aldasˮ cultivar. Chlorogenic acid and procyanidin C1 were the most significant contributors to total reducing and radical scavenging activity in all apple cultivars tested, therefore they could be considered as markers of antioxidant activity. PMID:27002313

  4. A proposed definition of the 'activity' of surface sites on lactose carriers for dry powder inhalation.

    PubMed

    Grasmeijer, Floris; Frijlink, Henderik W; de Boer, Anne H

    2014-06-01

    A new definition of the activity of surface sites on lactose carriers for dry powder inhalation is proposed which relates to drug detachment during dispersion. The new definition is expected to improve the understanding of 'carrier surface site activity', which stimulates the unambiguous communication about this subject and may aid in the rational design and interpretation of future formulation studies. In contrast to the currently prevailing view on carrier surface site activity, it follows from the newly proposed definition that carrier surface site activity depends on more variables than just the physicochemical properties of the carrier surface. Because the term 'active sites' is ambiguous, it is recommended to use the term 'highly active sites' instead to denote carrier surface sites with a relatively high activity. PMID:24613490

  5. Effects of microwave heating on porous structure of regenerated powdered activated carbon used in xylose.

    PubMed

    Li, Wei; Wang, Xinying; Peng, Jinhui

    2014-01-01

    The regeneration of spent powdered activated carbons used in xylose decolourization by microwave heating was investigated. Effects of microwave power and microwave heating time on the adsorption capacity of regenerated activated carbons were evaluated. The optimum conditions obtained are as follows: microwave power 800W; microwave heating time 30min. Regenerated activated carbon in this work has high adsorption capacities for the amount of methylene blue of 16 cm3/0.1 g and the iodine number of 1000.06mg/g. The specific surface areas of fresh commercial activated carbon, spent carbon and regenerated activated carbon were calculated according to the Brunauer, Emmett and Teller method, and the pore-size distributions of these carbons were characterized by non-local density functional theory (NLDFT). The results show that the specific surface area and the total pore volume of regenerated activated carbon are 1064 m2/g and 1.181 mL/g, respectively, indicating the feasibility of regeneration of spent powdered activated carbon used in xylose decolourization by microwave heating. The results of surface fractal dimensions also confirm the results of isotherms and NLDFT.

  6. Modeling high adsorption capacity and kinetics of organic macromolecules on super-powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Ando, Naoya; Yoshida, Tomoaki; Kurotobi, Ryuji; Matsushita, Taku; Ohno, Koichi

    2011-02-01

    The capacity to adsorb natural organic matter (NOM) and polystyrene sulfonates (PSSs) on small particle-size activated carbon (super-powdered activated carbon, SPAC) is higher than that on larger particle-size activated carbon (powdered-activated carbon, PAC). Increased adsorption capacity is likely attributable to the larger external surface area because the NOM and PSS molecules do not completely penetrate the adsorbent particle; they preferentially adsorb near the outer surface of the particle. In this study, we propose a new isotherm equation, the Shell Adsorption Model (SAM), to explain the higher adsorption capacity on smaller adsorbent particles and to describe quantitatively adsorption isotherms of activated carbons of different particle sizes: PAC and SPAC. The SAM was verified with the experimental data of PSS adsorption kinetics as well as equilibrium. SAM successfully characterized PSS adsorption isotherm data for SPACs and PAC simultaneously with the same model parameters. When SAM was incorporated into an adsorption kinetic model, kinetic decay curves for PSSs adsorbing onto activated carbons of different particle sizes could be simultaneously described with a single kinetics parameter value. On the other hand, when SAM was not incorporated into such an adsorption kinetic model and instead isotherms were described by the Freundlich model, the kinetic decay curves were not well described. The success of the SAM further supports the adsorption mechanism of PSSs preferentially adsorbing near the outer surface of activated carbon particles. PMID:21172719

  7. Effects of microwave heating on porous structure of regenerated powdered activated carbon used in xylose.

    PubMed

    Li, Wei; Wang, Xinying; Peng, Jinhui

    2014-01-01

    The regeneration of spent powdered activated carbons used in xylose decolourization by microwave heating was investigated. Effects of microwave power and microwave heating time on the adsorption capacity of regenerated activated carbons were evaluated. The optimum conditions obtained are as follows: microwave power 800W; microwave heating time 30min. Regenerated activated carbon in this work has high adsorption capacities for the amount of methylene blue of 16 cm3/0.1 g and the iodine number of 1000.06mg/g. The specific surface areas of fresh commercial activated carbon, spent carbon and regenerated activated carbon were calculated according to the Brunauer, Emmett and Teller method, and the pore-size distributions of these carbons were characterized by non-local density functional theory (NLDFT). The results show that the specific surface area and the total pore volume of regenerated activated carbon are 1064 m2/g and 1.181 mL/g, respectively, indicating the feasibility of regeneration of spent powdered activated carbon used in xylose decolourization by microwave heating. The results of surface fractal dimensions also confirm the results of isotherms and NLDFT. PMID:24645431

  8. The role of metals in modulating metalloprotease activity in the AD brain.

    PubMed

    Filiz, Gulay; Price, Katherine A; Caragounis, Aphrodite; Du, Tai; Crouch, Peter J; White, Anthony R

    2008-03-01

    Biometals such as copper and zinc have an important role in Alzheimer's disease (AD). Accumulating evidence indicates that copper homeostasis is altered in AD brain with elevated extracellular and low intracellular copper levels. Studies in animals and cell cultures have suggested that increasing intracellular copper can ameliorate AD-like pathology including amyloid deposition and tau phosphorylation. Modulating copper homeostasis can also improve cognitive function in animal models of AD. Treatments are now being developed that may result in redistribution of copper within the brain. Metal ligands such as clioquinol (CQ), DP-109 or pyrrolidine dithiocarbamate (PDTC) have shown promising results in animal models of AD, however, the actual mode of action in vivo has not been fully determined. We previously reported that CQ-metal complexes were able to increase intracellular copper levels in vitro. This resulted in stimulation of phosphoinositol-3-kinase activity and mitogen activated protein kinases (MAPK). Increased kinase activity resulted in up-regulated matrix metalloprotease (MMP2 and MMP3) activity resulting in enhanced degradation of secreted A beta. These findings are consistent with previous studies reporting metal-mediated activation of MAPKs and MMPs. How this activation occurs is unknown but evidence suggests that copper may be able to activate membrane receptors such as the epidermal growth factor receptor (EGFR) and result in downstream activation of MAPK pathways. This has been supported by studies showing metal-mediated activation of EGFR through ligand-independent processes in a number of cell-types. Our initial studies reveal that copper complexes can in fact activate EGFR. However, further studies are necessary to determine if metal complexes such as CQ-copper induce up-regulation of A beta-degrading MMP activity through this mechanism. Elucidation of this pathway may have important implications for the development of metal ligand based

  9. Influence of Shielding Gas and Mechanical Activation of Metal Powders on the Quality of Surface Sintered Layers

    NASA Astrophysics Data System (ADS)

    Saprykina, N. A.; Saprykin, A. A.; Arkhipova, D. A.

    2016-04-01

    The thesis analyses the influence of argon shielding gas and mechanical activation of PMS-1 copper powder and DSK-F75 cobalt chrome molybdenum powder on the surface sintered layer quality under various sintering conditions. Factors affecting the quality of the sintered surface and internal structure are studied. The obtained results prove positive impact of the shielding gas and mechanical activation. Sintering PMS-1 copper powder in argon shielding gas after mechanical activation leads to reduced internal stresses and roughness, as well as improved strength characteristics of the sintered surface. Analysis of sintered samples of mechanically activated DSK-F75 cobalt chrome molybdenum powder shows that the strength of the sintered surface grows porosity and coagulation changes.

  10. Assessment of the activity of antiperspirants added to surgical hand disinfectants: methodological aspects and first observations.

    PubMed

    Pitten, F A; Rudolph, P; Below, H; Kramer, A

    2001-08-01

    Due to the risk of sensitization caused by glove powder, the use of unpowdered latex gloves is increasing. These unpowdered gloves need a special inner-surface layer which makes it easier for the applicant to put the glove on the hand and to remove it again. However, many users report difficulties with removing the gloves because of sweat production within the glove. Therefore, a method has been developed to evaluate the efficacy of antiperspirants which may be added either to the inner-surface layer of the glove or to hand disinfectants or to skin-care products used before the gloves are put on. The paper describes various trials to optimize this method. PMID:11759021

  11. Controlling self-sustained spiking activity by adding or removing one network link

    NASA Astrophysics Data System (ADS)

    Xu, Kesheng; Huang, Wenwen; Li, Baowen; Dhamala, Mukesh; Liu, Zonghua

    2013-06-01

    Being able to control the neuronal spiking activity in specific brain regions is central to a treatment scheme in several brain disorders such as epileptic seizures, mental depression, and Parkinson's diseases. Here, we present an approach for controlling self-sustained oscillations by adding or removing one directed network link in coupled neuronal oscillators, in contrast to previous approaches of adding stimuli or noise. We find that such networks can exhibit a variety of activity patterns such as on-off switch, sustained spikes, and short-term spikes. We derive the condition for a specific link to be the controller of the on-off effect. A qualitative analysis is provided to facilitate the understanding of the mechanism for spiking activity by adding one link. Our findings represent the first report on generating spike activity with the addition of only one directed link to a network and provide a deeper understanding of the microscopic roots of self-sustained spiking.

  12. Somatostatin modulates insulin-degrading-enzyme metabolism: implications for the regulation of microglia activity in AD.

    PubMed

    Tundo, Grazia; Ciaccio, Chiara; Sbardella, Diego; Boraso, Mariaserena; Viviani, Barbara; Coletta, Massimiliano; Marini, Stefano

    2012-01-01

    The deposition of β-amyloid (Aβ) into senile plaques and the impairment of somatostatin-mediated neurotransmission are key pathological events in the onset of Alzheimer's disease (AD). Insulin-degrading-enzyme (IDE) is one of the main extracellular protease targeting Aβ, and thus it represents an interesting pharmacological target for AD therapy. We show that the active form of somatostatin-14 regulates IDE activity by affecting its expression and secretion in microglia cells. A similar effect can also be observed when adding octreotide. Following a previous observation where somatostatin directly interacts with IDE, here we demonstrate that somatostatin regulates Aβ catabolism by modulating IDE proteolytic activity in IDE gene-silencing experiments. As a whole, these data indicate the relevant role played by somatostatin and, potentially, by analogue octreotide, in preventing Aβ accumulation by partially restoring IDE activity.

  13. An efficient synthesis method targeted to marine alkaloids marinacarbolines A-D and their antitumor activities.

    PubMed

    Li, Jun; Tang, Yang; Jin, Hui-Juan; Cui, Yi-Di; Zhang, Li-Juan; Jiang, Tao

    2015-01-01

    Marinacarbolines A-D are a series of marine β-carboline alkaloids isolated from actinomycete Marinactinospora thermotolerans of the deep South China Sea with antiplasmodial activities. In inhibition assays of in vitro growth of Plasmodium falciparum, marinacarbolines exhibited antiplasmodial activity against drug-sensitive line 3D7 and drug-resistant line Dd2 of P. falciparum. However, approaches for the synthesis of such useful compounds are very limited. In this work, we reported a simple, efficient, and versatile process to synthesize marinacarbolines A-D (1-4). On the basis of that, the antitumor activities of marinacarbolines in a structure-dependent manner were allowed to be unveiled.

  14. Photocatalytic Activity of LaSr2 AlO5 :Eu Ceramic Powders.

    PubMed

    García, Carlos R; Oliva, Jorge; Díaz-Torres, Luis A

    2015-01-01

    The photocatalytic activity, of undoped and Europium-doped LaSr2 AlO5 powders, has been investigated by degrading methylene blue dye in water solutions. Those powders were fabricated by a combustion method and an annealing treatment in air. All samples showed a tetragonal single phase according to by X-ray diffraction measurements (XRD). Scanning electron microscopy (SEM) revealed irregular semi-oval grains with sizes in the range of 3.5-4.27 μm. Photoluminescence spectrum showed sharp emission peaks at 588 nm and at 617 nm which are associated with (7) F1 ,(7) F2 → (5) D0 Eu(3+) ion forbidden transitions, respectively, under UV light excitation of 322 nm. The methylene blue (MB) degradation under UV light (254 nm) was studied by monitoring changes in the absorbance peak of MB at 665 nm. Finally, LaSr2 AlO5 :Eu powders were used three times and the efficiency for the degradation of MB decreased from 100 to 61% after the third cycle of use.

  15. Adsorption of malachite green on groundnut shell waste based powdered activated carbon

    SciTech Connect

    Malik, R.; Ramteke, D.S. Wate, S.R.

    2007-07-01

    In the present technologically fast changing situation related to waste management practices, it is desirable that disposal of plant waste should be done in a scientific manner by keeping in view economic and pollution considerations. This is only possible when the plant waste has the potential to be used as raw material for some useful product. In the present study, groundnut shell, an agricultural waste, was used for the preparation of an adsorbent by chemical activation using ZnCl{sub 2} under optimized conditions and its comparative characterisation was conducted with commercially available powdered activated carbon (CPAC) for its physical, chemical and adsorption properties. The groundnut shell based powdered activated carbon (GSPAC) has a higher surface area, iodine and methylene blue number compared to CPAC. Both of the carbons were used for the removal of malachite green dye from aqueous solution and the effect of various operating variables, viz. adsorbent dose (0.1-1 g l{sup -1}), contact time (5-120 min) and adsorbate concentrations (100-200 mg l{sup -1}) on the removal of dye, has been studied. The experimental results indicate that at a dose of 0.5 g l{sup -1} and initial concentration of 100 mg l{sup -1}, GSPAC showed 94.5% removal of the dye in 30 min equilibrium time, while CPAC removed 96% of the dye in 15 min. The experimental isotherm data were analyzed using the linearized forms of Freundlich, Langmuir and BET equations to determine maximum adsorptive capacities. The equilibrium data fit well to the Freundlich isotherm, although the BET isotherm also showed higher correlation for both of the carbons. The results of comparative adsorption capacity of both carbons indicate that groundnut shell can be used as a low-cost alternative to commercial powdered activated carbon in aqueous solution for dye removal.

  16. Adsorption of malachite green on groundnut shell waste based powdered activated carbon.

    PubMed

    Malik, R; Ramteke, D S; Wate, S R

    2007-01-01

    In the present technologically fast changing situation related to waste management practices, it is desirable that disposal of plant waste should be done in a scientific manner by keeping in view economic and pollution considerations. This is only possible when the plant waste has the potential to be used as raw material for some useful product. In the present study, groundnut shell, an agricultural waste, was used for the preparation of an adsorbent by chemical activation using ZnCl2 under optimized conditions and its comparative characterisation was conducted with commercially available powdered activated carbon (CPAC) for its physical, chemical and adsorption properties. The groundnut shell based powdered activated carbon (GSPAC) has a higher surface area, iodine and methylene blue number compared to CPAC. Both of the carbons were used for the removal of malachite green dye from aqueous solution and the effect of various operating variables, viz. adsorbent dose (0.1-1 g l(-1)), contact time (5-120 min) and adsorbate concentrations (100-200 mg l(-1)) on the removal of dye, has been studied. The experimental results indicate that at a dose of 0.5 g l(-1) and initial concentration of 100 mg l(-1), GSPAC showed 94.5% removal of the dye in 30 min equilibrium time, while CPAC removed 96% of the dye in 15 min. The experimental isotherm data were analyzed using the linearized forms of Freundlich, Langmuir and BET equations to determine maximum adsorptive capacities. The equilibrium data fit well to the Freundlich isotherm, although the BET isotherm also showed higher correlation for both of the carbons. The results of comparative adsorption capacity of both carbons indicate that groundnut shell can be used as a low-cost alternative to commercial powdered activated carbon in aqueous solution for dye removal.

  17. Determination of alumina in sintered aluminium powder by activation with 14-MeV neutrons.

    PubMed

    Español, C E; Marafuschi, A M

    1970-07-01

    Fast neutrons of 14 MeV produced in the IMICAM CISE 150-kV generator by the (d, t) reaction in a tritium-titanium target, were used in the indirect determination of Al(2)O(3). The samples were irradiated for 30 sec and the total (16)N activity was determined, by counting for ten 2-sec periods and graphically integrating. The standards were a known sintered aluminium powder and nylon pieces of identical shape. The method is competitive with the chemical one, because of its quickness, sensitivity and precision. PMID:18960787

  18. Effect of low dosages of powdered activated carbon on membrane bioreactor performance.

    PubMed

    Remy, Maxime; Temmink, Hardy; Rulkens, Wim

    2012-01-01

    Previous research has demonstrated that powdered activated carbon (PAC), when applied at very low dosages and long SRTs, reduces membrane fouling in membrane bioreactors (MBRs). This effect was related to the formation of stronger sludge flocs, which are less sensitive to shear. In this contribution the long-term effect of PAC addition was studied by running two parallel MBRs on sewage. To one of these, PAC was dosed and a lower fouling tendency of the sludge was verified, with a 70% longer sustainable filtration time. Low PAC dosages showed additional advantages with regard to oxygen transfer and dewaterability, which may provide savings on operational costs. PMID:22339033

  19. Synthesis of nano-sized amorphous boron powders through active dilution self-propagating high-temperature synthesis method

    SciTech Connect

    Wang, Jilin; Gu, Yunle; Li, Zili; Wang, Weimin; Fu, Zhengyi

    2013-06-01

    Graphical abstract: Nano-sized amorphous boron powders were synthesized by active dilution self-propagating high-temperature synthesis (SHS) method. The effects of endothermic reaction rate, the possible chemical reaction mechanism and active dilution model for synthesis of the product were also discussed. Highlights: ► Nano-sized amorphous boron powders were synthesized by active dilution self-propagating high-temperature synthesis method. ► The morphology, particle size and purity of the samples could be effectively controlled via changing the endothermic rate. ► The diluter KBH{sub 4} played an important role in active dilution synthesis of amorphous nano-sized boron powders. ► The active dilution method could be further popularized and become a common approach to prepare various inorganic materials. - Abstract: Nano-sized amorphous boron powders were synthesized by active dilution self-propagating high-temperature synthesis (SHS) method at temperatures ranging from 700 °C to 850 °C in a SHS furnace using Mg, B{sub 2}O{sub 3} and KBH{sub 4} as raw materials. Samples were characterized by X-ray powder diffraction (XRD), Laser particle size analyzer, Fourier transform infrared spectra (FTIR), X-ray energy dispersive spectroscopy (EDX), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution transmission TEM (HRTEM). The boron powders demonstrated an average particle size of 50 nm with a purity of 95.64 wt.%. The diluter KBH{sub 4} played an important role in the active dilution synthesis of amorphous nano-sized boron powders. The effects of endothermic reaction rate, the possible chemical reaction mechanism and active dilution model for synthesis of the product were also discussed.

  20. BACE1 activity in cerebrospinal fluid and its relation to markers of AD pathology.

    PubMed

    Mulder, Sandra D; van der Flier, Wiesje M; Verheijen, Jan H; Mulder, Cees; Scheltens, Philip; Blankenstein, Marinus A; Hack, C Erik; Veerhuis, Robert

    2010-01-01

    Several studies have shown that reduced amyloid-beta 1-42 (Abeta(42)) and increased tau levels in cerebrospinal fluid (CSF) reflect increased Alzheimer's disease (AD) pathology in the brain. beta-site APP cleaving enzyme (BACE1) is thought to be the major beta-secretase involved in Abeta production in the brain, and therefore we investigated the relation between BACE1 activity and CSF markers Abeta(40), Abeta(42), total tau (t-tau), and tau phosphorylated at threonine 181 (p-tau) in CSF of control (n=12), mild cognitive impairment (n=18), and AD (n=17) subjects. Patients were classified according to their Abeta(42), t-tau, and p-tau CSF biomarker levels, with either an AD-like biomarker profile (two or three biomarkers abnormal: Abeta(42) < 495 pg/ml in combination with t-tau > 356 pg/ml, and/or p-tau > 54 pg/ml) or a normal biomarker profile (AD-like biomarker profile (66 +/- 6 years, 53% female, and Mini-Mental Status Examination (MMSE) score: 23 +/- 5) and 28 subjects with a normal biomarker profile (62 +/- 11 years, 43% female, and MMSE score: 27 +/- 4). Subjects with an AD-like biomarker profile had higher CSF BACE1 activity levels, compared to patients with a normal biomarker profile (20 pg/ml and 16 pg/ml respectively; p=0.01), when controlled for age and gender. In the whole sample, BACE1 activity correlated with CSF levels of Abeta(40), t-tau, and p-tau (r=0.38, r=0.63, and r=0.65; all p< 0.05), but not with Abeta(42). These data suggest that increased BACE1 activity in CSF relates to AD pathology in the brain.

  1. BACE1 activity in cerebrospinal fluid and its relation to markers of AD pathology.

    PubMed

    Mulder, Sandra D; van der Flier, Wiesje M; Verheijen, Jan H; Mulder, Cees; Scheltens, Philip; Blankenstein, Marinus A; Hack, C Erik; Veerhuis, Robert

    2010-01-01

    Several studies have shown that reduced amyloid-beta 1-42 (Abeta(42)) and increased tau levels in cerebrospinal fluid (CSF) reflect increased Alzheimer's disease (AD) pathology in the brain. beta-site APP cleaving enzyme (BACE1) is thought to be the major beta-secretase involved in Abeta production in the brain, and therefore we investigated the relation between BACE1 activity and CSF markers Abeta(40), Abeta(42), total tau (t-tau), and tau phosphorylated at threonine 181 (p-tau) in CSF of control (n=12), mild cognitive impairment (n=18), and AD (n=17) subjects. Patients were classified according to their Abeta(42), t-tau, and p-tau CSF biomarker levels, with either an AD-like biomarker profile (two or three biomarkers abnormal: Abeta(42) < 495 pg/ml in combination with t-tau > 356 pg/ml, and/or p-tau > 54 pg/ml) or a normal biomarker profile (AD-like biomarker profile (66 +/- 6 years, 53% female, and Mini-Mental Status Examination (MMSE) score: 23 +/- 5) and 28 subjects with a normal biomarker profile (62 +/- 11 years, 43% female, and MMSE score: 27 +/- 4). Subjects with an AD-like biomarker profile had higher CSF BACE1 activity levels, compared to patients with a normal biomarker profile (20 pg/ml and 16 pg/ml respectively; p=0.01), when controlled for age and gender. In the whole sample, BACE1 activity correlated with CSF levels of Abeta(40), t-tau, and p-tau (r=0.38, r=0.63, and r=0.65; all p< 0.05), but not with Abeta(42). These data suggest that increased BACE1 activity in CSF relates to AD pathology in the brain. PMID:20164582

  2. Branched pore kinetic model analysis of geosmin adsorption on super-powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Ando, Naoya; Sasaki, Hiroshi; Matsushita, Taku; Ohno, Koichi

    2009-07-01

    Super-powdered activated carbon (S-PAC) is activated carbon of much finer particle size than powdered activated carbon (PAC). Geosmin is a naturally occurring taste and odor compound that impairs aesthetic quality in drinking water. Experiments on geosmin adsorption on S-PAC and PAC were conducted, and the results using adsorption kinetic models were analyzed. PAC pulverization, which produced the S-PAC, did not change geosmin adsorption capacity, and geosmin adsorption capacities did not differ between S-PAC and PAC. Geosmin adsorption kinetics, however, were much higher on S-PAC than on PAC. A solution to the branched pore kinetic model (BPKM) was developed, and experimental adsorption kinetic data were analyzed by BPKM and by a homogeneous surface diffusion model (HSDM). The HSDM describing the adsorption behavior of geosmin required different surface diffusivity values for S-PAC and PAC, which indicated a decrease in surface diffusivity apparently associated with activated carbon particle size. The BPKM, consisting of macropore diffusion followed by mass transfer from macropore to micropore, successfully described the batch adsorption kinetics on S-PAC and PAC with the same set of model parameter values, including surface diffusivity. The BPKM simulation clearly showed geosmin removal was improved as activated carbon particle size decreased. The simulation also implied that the rate-determining step in overall mass transfer shifted from intraparticle radial diffusion in macropores to local mass transfer from macropore to micropore. Sensitivity analysis showed that adsorptive removal of geosmin improved with decrease in activated carbon particle size down to 1microm, but further particle size reduction produced little improvement.

  3. Active Thermography for the Detection of Defects in Powder Metallurgy Compacts

    SciTech Connect

    Benzerrouk, Souheil; Ludwig, Reinhold; Apelian, Diran

    2007-03-21

    Active thermography is an established NDE technique that has become the method of choice in many industrial applications which require non-contact access to the parts under test. Unfortunately, when conducting on-line infrared (IR) inspection of powder metallic compacts, complications can arise due the generally low emissivity of metals and the thermally noisy environment typically encountered in manufacturing plants. In this paper we present results of an investigation that explores the suitability of active IR imaging of powder metallurgy compacts for the detection of surface and sub-surface defects in the pre-sinter state and in an on-line manufacturing setting to ensure complete quality assurance. Additional off-line tests can be carried out for statistical quality analyses. In this research, the IR imaging of sub-surface defects is based on a transient instrumentation approach that relies on an electric control system which synchronizes and monitors the thermal response due to an electrically generated heat source. Preliminary testing reveals that this newly developed pulsed thermography system can be employed for the detection of subsurface defects in green-state parts. Practical measurements agree well with theoretical predictions. The inspection approach being developed can be used for the testing of green-state compacts as they exit the compaction press at speeds of up to 1,000 parts per hour.

  4. Inuloxins A-D and derivatives as antileishmanial agents: structure-activity relationship study

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Inuloxins A-D (1-4) and a-costic acid (5), the phytotoxic compounds previously isolated from Inula viscosa, as well as synthetic derivatives of inuloxin A (compounds 6-10), inuloxin C (compound 11) and inuloxin D (compound 12) were tested in vitro for their activity against Leishmania donovani, the ...

  5. The Formation of Carbon Nanofibers on Powdered Activated Carbon Impregnated with Nickel

    NASA Astrophysics Data System (ADS)

    Ahmed, Y. M.; Al-Mamun, A. A.; Muyibi, S. A.; Al-Khatib, M. F. R.; Jameel, A. T.; AlSaadi, M. A.

    2009-06-01

    In the present work, the production and characterization of carbon nanofibers (CNFs) composite is reported. Carbon nanofibers (CNF) were produced on powdered activated carbon PAC—impregnated with nickel—by Chemical Vapor Deposition (CVD) of a hydrocarbon in the presence of hydrogen at ˜780° C. The flow rates of carbon source and hydrogen were fixed. The CNFs were formed directly over the impregnated AC. Variable weight percentage ratios of the catalyst salt (Ni+2) were used for the impregnation (1, 3, 5, 7 and 9%, respectively). The product displays a relatively high surface area, essentially constituted by the external surface, and the absence of the bottled pores encountered with activated carbon. FSEM, TEM and TGA were used for the characterization of the product.

  6. Effect of powdered activated carbon (PAC) and cationic polymer on biofouling mitigation in hybrid MBRs.

    PubMed

    Jamal Khan, S; Visvanathan, C; Jegatheesan, V

    2012-06-01

    In this study, the influence of powdered activated carbon (PAC) and cationic polymer (MPE50) was investigated on the fouling propensity in hybrid MBRs. Three laboratory scale MBRs were operated simultaneously including MBR(Control), MBR(PAC), and MBR(Polymer). Optimum dosages of PAC and polymer to the MBR(PAC) and MBR(Polymer), respectively were determined using jar tests. It was found that the MBR(PAC) exhibited low fouling tendency and prolonged filtration as compared to the other MBRs. Improved filtration in MBR(PAC) was attributed to the flocculation and adsorption phenomena. The effective stability of the biomass by PAC in the form of biological activated carbon (BAC) was verified by the increase in mean particle size. The BAC aided sludge layer exhibited porous cake structure resulting in the prolong filtration. However, both the membrane hybrid systems revealed effective adsorption of organic matter by 40% reduction in the soluble EPS concentration. PMID:22264429

  7. Optimization of membrane bioreactors by the addition of powdered activated carbon.

    PubMed

    Ng, Choon Aun; Sun, Darren; Bashir, Mohammed J K; Wai, Soon Han; Wong, Ling Yong; Nisar, Humaira; Wu, Bing; Fane, Anthony G

    2013-06-01

    It was found that with replenishment, powdered activated carbon (PAC) in the membrane bioreactor (MBR) would develop biologically activated carbon (BAC) which could enhance filtration performance of a conventional MBR. This paper addresses two issues (i) effect of PAC size on MBR (BAC) performance; and (ii) effect of sludge retention time (SRT) on the MBR performance with and without PAC. To interpret the trends, particle/floc size, concentration of mixed liquor suspended solid (MLSS), total organic carbon (TOC), short-term filtration properties and transmembrane pressure (TMP) versus time are measured. The results showed improved fouling control with fine, rather than coarse, PAC provided the flux did not exceed the deposition flux for the fine PAC. Without PAC, the longer SRT operation gave lower fouling at modest fluxes. With PAC addition, the shorter SRT gave better fouling control, possibly due to greater replenishment of the fresh PAC. PMID:23612160

  8. Estimates of increased black carbon emissions from electrostatic precipitators during powdered activated carbon injection for mercury emissions control.

    PubMed

    Clack, Herek L

    2012-07-01

    The behavior of mercury sorbents within electrostatic precipitators (ESPs) is not well-understood, despite a decade or more of full-scale testing. Recent laboratory results suggest that powdered activated carbon exhibits somewhat different collection behavior than fly ash in an ESP and particulate filters located at the outlet of ESPs have shown evidence of powdered activated carbon penetration during full-scale tests of sorbent injection for mercury emissions control. The present analysis considers a range of assumed differential ESP collection efficiencies for powdered activated carbon as compared to fly ash. Estimated emission rates of submicrometer powdered activated carbon are compared to estimated emission rates of particulate carbon on submicrometer fly ash, each corresponding to its respective collection efficiency. To the extent that any emitted powdered activated carbon exhibits size and optical characteristics similar to black carbon, such emissions could effectively constitute an increase in black carbon emissions from coal-based stationary power generation. The results reveal that even for the low injection rates associated with chemically impregnated carbons, submicrometer particulate carbon emissions can easily double if the submicrometer fraction of the native fly ash has a low carbon content. Increasing sorbent injection rates, larger collection efficiency differentials as compared to fly ash, and decreasing sorbent particle size all lead to increases in the estimated submicrometer particulate carbon emissions. PMID:22663136

  9. Survival of Enterobacter sakazakii in powdered infant formula as affected by composition, water activity, and temperature.

    PubMed

    Gurtler, Joshua B; Beuchat, Larry R

    2007-07-01

    A study was done to determine survival characteristics of Enterobacter sakazakii in four milk-based and two soybean-based powdered infant formulas. A 10-strain mixture of E. sakazakii was inoculated into the six infant formulas at water activity (aw) 0.25 to 0.30, 0.31 to 0.33, and 0.43 to 0.50 to give low (0.80 log CFU/g) and high (4.66 to 4.86 log CFU/g) populations. At an initial population of 0.80 log CFU/g, E. sakazakii was detected by enrichment in six of six, four of six, and one of six formulas stored for 12 months at 4, 21, and 30 degrees C, respectively. In four of six formulas at aw values of 0.25 to 0.30, initially high populations decreased significantly (P < or = 0.05), although by less than 1 log CFU/g, within 6 months at 4 degrees C. Populations decreased significantly in all formulas in the aw range of 0.25 to 0.50 during storage for 1 month at 21 or 30 degrees C and again between 1 and 6 months in most formulas. Significant reductions occurred between 6 and 12 months in some formulas. At all storage temperatures, reductions in populations tended to be greater in formulas at aw 0.43 to 0.50 than in formulas at aw 0.25 to 0.30. The rate of inactivation of E. sakazakii in formulas was not markedly influenced by formula composition. Cells from mucoid and nonmucoid colonies formed by two strains on violet red bile glucose agar supplemented with pyruvate were inoculated into a milk-based powdered infant formula and a soybean-based powdered infant formula having a high aw range of 0.43 to 0.86 and stored at 4, 21, and 30 degrees C for up to 36 weeks. With few exceptions, populations of both strains decreased significantly in both formulas within 2 weeks at all temperatures; rates of death increased with increased aw and storage temperature. The presence of mucoidal extracellular materials on the surface of E. sakazakii cells was not associated with protection against death. This study shows that the retention of viability of E. sakazakii in powdered

  10. The Influence of AD Family History and APOE4 on Mesial Temporal Lobe Activation

    PubMed Central

    Johnson, Sterling C.; Schmitz, Taylor W.; Trivedi, Mehul A.; Ries, Michele L.; Torgerson, Britta M.; Carlsson, Cynthia; Asthana, Sanjay; Hermann, Bruce P.; Sager, Mark A.

    2009-01-01

    First-degree family history of sporadic Alzheimer Disease (AD) and the apolipoprotein E ε4 (APOE4) are risk factors for developing AD. Although the role of APOE4 in AD pathogenesis has been well studied, family history remains a rarely studied and poorly understood risk factor. Both putatively cause early brain changes prior to symptomatic disease, but the relative contribution of each on brain function is unknown. We examined 68 middle-aged participants with a parent diagnosed with AD (+FH) and 64 age- and education-matched controls without a first-degree family history of any dementia (−FH). All underwent cognitive testing, APOE genotyping and a functional MRI (fMRI) encoding task that required discrimination of novel items from previously learned items. A 2 × 2 factorial ANOVA (presence/absence of parental family history and presence/absence of the APOE4) was used to detect group effects. A greater response to novel items was detected in the mesial temporal lobe and fusiform gyrus bilaterally among persons without a first-degree family history of AD. In hippocampal areas, the −FH +ε4 group exhibited the greatest signal change, and the +FH +ε4 group the least. These findings indicate that FH of AD is an important predictor of hippocampal activation during encoding and that FH may modulate the effect of APOE4 in these middle-aged adults, suggesting that an as yet unspecified factor embodied in first-degree family history of AD is influencing the expression of APOE4 on brain function. PMID:16738250

  11. Phosphorus as sintering activator in powder metallurgical steels: characterization of the distribution and its technological impact.

    PubMed

    Krecar, Dragan; Vassileva, Vassilka; Danninger, Herbert; Hutter, Herbert

    2004-06-01

    Powder metallurgy is a highly developed method of manufacturing reliable ferrous parts. The main processing steps in a powder metallurgical line are pressing and sintering. Sintering can be strongly enhanced by the formation of a liquid phase during the sintering process when using phosphorus as sintering activator. In this work the distribution (effect) of phosphorus was investigated by means of secondary ion mass spectrometry (SIMS) supported by Auger electron spectroscopy (AES) and electron probe micro analysis (EPMA). To verify the influence of the process conditions (phosphorus content, sintering atmosphere, time) on the mechanical properties, additional measurements of the microstructure (pore shape) and of impact energy were performed. Analysis of fracture surfaces was performed by means of scanning electron microscopy (SEM). The concentration of phosphorus differs in the samples from 0 to 1% (w/ w). Samples with higher phosphorus concentrations (1% (w/ w) and above) are also measurable by EPMA, whereas the distributions of P at technically relevant concentrations and the distribution of possible impurities are only detectable (visible) by means of SIMS. The influence of the sintering time on the phosphorus distribution will be demonstrated. In addition the grain boundary segregation of P was measured by AES at the surface of in-situ broken samples. It will be shown that the distribution of phosphorus depends also on the concentration of carbon in the samples.

  12. Large zinc cation occupancy of octahedral sites in mechanically activated zinc ferrite powders

    SciTech Connect

    Oliver, S. A.; Harris, V. G.; Hamdeh, H. H.; Ho, J. C.

    2000-05-08

    The cation site occupancy of a mechanically activated nanocrystalline zinc ferrite powder was determined as (Zn{sub 0.55}{sup 2+}Fe{sub 0.18}{sup 3+}){sub tet}[Zr{sub 0.45}{sup 2+}Fe{sub 1.82}{sup 3+}]{sub oct}O{sub 4} through analysis of extended x-ray absorption fine structure measurements, showing a large redistribution of cations between sites compared to normal zinc ferrite samples. The overpopulation of cations in the octahedral sites was attributed to the ascendance in importance of the ionic radii over the crystal energy and bonding coordination in determining which interstitial sites are occupied in this structurally disordered powder. Slight changes are observed in the local atomic environment about the zinc cations, but not the iron cations, with respect to the spinel structure. The presence of Fe{sup 3+} on both sites is consistent with the measured room temperature magnetic properties. (c) 2000 American Institute of Physics.

  13. Direct observation of solid-phase adsorbate concentration profile in powdered activated carbon particle to elucidate mechanism of high adsorption capacity on super-powdered activated carbon.

    PubMed

    Ando, Naoya; Matsui, Yoshihiko; Matsushita, Taku; Ohno, Koichi

    2011-01-01

    Decreasing the particle size of powdered activated carbon (PAC) by pulverization increases its adsorption capacities for natural organic matter (NOM) and polystyrene sulfonate (PSS, which is used as a model adsorbate). A shell adsorption mechanism in which NOM and PSS molecules do not completely penetrate the adsorbent particle and instead preferentially adsorb near the outer surface of the particle has been proposed as an explanation for this adsorption capacity increase. In this report, we present direct evidence to support the shell adsorption mechanism. PAC particles containing adsorbed PSS were sectioned with a focused ion beam, and the solid-phase PSS concentration profiles of the particle cross-sections were directly observed by means of field emission-scanning electron microscopy/energy-dispersive X-ray spectrometry (FE-SEM/EDXS). X-ray emission from sulfur, an index of PSS concentration, was higher in the shell region than in the inner region of the particles. The X-ray emission profile observed by EDXS did not agree completely with the solid-phase PSS concentration profile predicted by shell adsorption model analysis of the PSS isotherm data, but the observed and predicted profiles were not inconsistent when the analytical errors were considered. These EDXS results provide the first direct evidence that PSS is adsorbed mainly in the vicinity of the external surface of the PAC particles, and thus the results support the proposition that the increase in NOM and PSS adsorption capacity with decreasing particle size is due to the increase in external surface area on which the molecules can be adsorbed. PMID:20851447

  14. Physical activity attenuates age-related biomarker alterations in preclinical AD

    PubMed Central

    Schultz, Stephanie A.; Oh, Jennifer M.; Larson, Jordan; Edwards, Dorothy; Cook, Dane; Koscik, Rebecca; Gallagher, Catherine L.; Dowling, N.M.; Carlsson, Cynthia M.; Bendlin, Barbara B.; LaRue, Asenath; Rowley, Howard A.; Christian, Brad T.; Asthana, Sanjay; Hermann, Bruce P.; Johnson, Sterling C.; Sager, Mark A.

    2014-01-01

    Objective: To examine whether engagement in physical activity might favorably alter the age-dependent evolution of Alzheimer disease (AD)-related brain and cognitive changes in a cohort of at-risk, late-middle-aged adults. Methods: Three hundred seventeen enrollees in the Wisconsin Registry for Alzheimer's Prevention underwent T1 MRI; a subset also underwent 11C-Pittsburgh compound B–PET (n = 186) and 18F-fluorodeoxyglucose–PET (n = 152) imaging. Participants' responses on a self-report measure of current physical activity were used to classify them as either physically active or physically inactive based on American Heart Association guidelines. They also completed a comprehensive neuropsychological battery. Covariate-adjusted regression analyses were used to test whether the adverse effect of age on imaging and cognitive biomarkers was modified by physical activity. Results: There were significant age × physical activity interactions for β-amyloid burden (p = 0.014), glucose metabolism (p = 0.015), and hippocampal volume (p = 0.025) such that, with advancing age, physically active individuals exhibited a lesser degree of biomarker alterations compared with the physically inactive. Similar age × physical activity interactions were also observed on cognitive domains of Immediate Memory (p = 0.042) and Visuospatial Ability (p = 0.016). In addition, the physically active group had higher scores on Speed and Flexibility (p = 0.002) compared with the inactive group. Conclusions: In a middle-aged, at-risk cohort, a physically active lifestyle is associated with an attenuation of the deleterious influence of age on key biomarkers of AD pathophysiology. However, because our observational, cross-sectional design cannot establish causality, randomized controlled trials/longitudinal studies will be necessary for determining whether midlife participation in structured physical exercise forestalls the development of AD and related disorders in later life. PMID:25298312

  15. Bisphenol A removal by combination of powdered activated carbon adsorption and ultrafiltration

    NASA Astrophysics Data System (ADS)

    Wang, Rongchang; Tong, Hao; Xia, Siqing; Zhang, Yalei; Zhao, Jianfu

    2010-11-01

    Bisphenol A (BPA) removal from surface water in the presence of natural organic matter (NOM) by combination of powdered activated carbon (PAC) adsorption and ultrafiltration (UF) was investigated in this study. It was especially focused on the effects of various factors on BPA removal, such as PAC dosage, NOM concentration and pH value. BPA removal by UF+PAC process increased sharply from 4% to 92%, when PAC dosage increased from 0 to 120 mg/L. The optimal PAC dosage was determined to be 30 mg/L. The results also showed that BPA retention was slightly favored in the presence of NOM. As pH increased from 7.0 to 10.5, BPA removal substantially decreased from 90% to 59%. PAC+UF process is recommended to be used as an emergence facility in drinking water treatment, especially when an accidental spilling of deleterious substance, e.g., BPA, in the water resources happens.

  16. Effect of powdered activated carbon technology on short-cut nitrogen removal for coal gasification wastewater.

    PubMed

    Zhao, Qian; Han, Hongjun; Xu, Chunyan; Zhuang, Haifeng; Fang, Fang; Zhang, Linghan

    2013-08-01

    A combined process consisting of a powdered activated carbon technology (PACT) and short-cut biological nitrogen removal reactor (SBNR) was developed to enhance the removal efficiency of the total nitrogen (TN) from the effluent of an upflow anaerobic sludge bed (UASB) reactor, which was used to treat coal gasification wastewater (CGW). The SBNR performance was improved with the increasing of COD and TP removal efficiency via PACT. The average removal efficiencies of COD and TP in PACT were respectively 85.80% and 90.30%. Meanwhile, the NH3-N to NO2-N conversion rate was achieved 86.89% in SBNR and the total nitrogen (TN) removal efficiency was 75.54%. In contrast, the AOB in SBNR was significantly inhibited without PACT or with poor performance of PACT in advance, which rendered the removal of TN. Furthermore, PAC was demonstrated to remove some refractory compounds, which therefore improved the biodegradability of the coal gasification wastewater. PMID:23735800

  17. Treatment of coal gasification wastewater by membrane bioreactor hybrid powdered activated carbon (MBR–PAC) system.

    PubMed

    Jia, Shengyong; Han, Hongjun; Hou, Baolin; Zhuang, Haifeng; Fang, Fang; Zhao, Qian

    2014-12-01

    A laboratory-scale membrane bioreactor hybrid powdered activated carbon (MBR–PAC) system was developed to treat coal gasification wastewater to enhance the COD, total phenols (TPh), NH4+ removals and migrate the membrane fouling. Since the MBR–PAC system operated with PAC dosage of 4 g L−1, the maximum removal efficiencies of COD, TPh and NH4+ reached 93%, 99% and 63%, respectively with the corresponding influent concentrations of 2.27 g L−1, 497 mg L−1 and 164 mg N L−1; the PAC extraction efficiencies of COD, TPh and NH4+ were 6%, 3% and 13%, respectively; the transmembrane pressure decreased 34% with PAC after 50 d operation. The results demonstrate that PAC played a key role in the enhancement of biodegradability and mitigation of membrane fouling. PMID:25461944

  18. Effect of powdered activated carbon technology on short-cut nitrogen removal for coal gasification wastewater.

    PubMed

    Zhao, Qian; Han, Hongjun; Xu, Chunyan; Zhuang, Haifeng; Fang, Fang; Zhang, Linghan

    2013-08-01

    A combined process consisting of a powdered activated carbon technology (PACT) and short-cut biological nitrogen removal reactor (SBNR) was developed to enhance the removal efficiency of the total nitrogen (TN) from the effluent of an upflow anaerobic sludge bed (UASB) reactor, which was used to treat coal gasification wastewater (CGW). The SBNR performance was improved with the increasing of COD and TP removal efficiency via PACT. The average removal efficiencies of COD and TP in PACT were respectively 85.80% and 90.30%. Meanwhile, the NH3-N to NO2-N conversion rate was achieved 86.89% in SBNR and the total nitrogen (TN) removal efficiency was 75.54%. In contrast, the AOB in SBNR was significantly inhibited without PACT or with poor performance of PACT in advance, which rendered the removal of TN. Furthermore, PAC was demonstrated to remove some refractory compounds, which therefore improved the biodegradability of the coal gasification wastewater.

  19. Cholesteryl ester transfer protein activity and atherogenic parameters in rabbits supplemented with cholesterol and garlic powder.

    PubMed

    Kwon, Myung-Ja; Song, Young-Sun; Choi, Myung-Sook; Park, Sang-Joon; Jeong, Kyu-Shik; Song, Yeong-Ok

    2003-05-16

    The current study was conducted to examine the effect of garlic supplementation on CETP activity, along with its anti-atherosclerotic effect in cholesterol-fed rabbits. Rabbits were fed a 1% cholesterol diet for 12 weeks, including a 1% garlic powder supplement. The garlic-supplemented group exhibited significantly lower CETP activity than the control group during the experimental period (P < 0.05). Among the atherogenic parameters, the total cholesterol, TG, LDL-C, VLDL-C, and atherogenic index were all significantly lower in the garlic group than in the control group during the experimental period (P < 0.05), whereas the HDL-C concentration was significantly higher in the garlic group than in the control group after 12 weeks (P < 0.05). Atherosclerotic lesion area in the aorta arch was also significantly lower in the garlic group (P < 0.05). In the morphological examination, the garlic-supplemented group exhibited far fewer fat droplet deposits than the control group. Furthermore, the garlic supplement also lowered the aortic and hepatic cholesterol, and triglyceride. Accordingly, the current results suggest that garlic exerts hypocholesterolemic and/or antiatherogenic and that plasma CETP activity might be a risk marker related with atherogenesis. As such, the inhibition of CETP activity may delay the progression of atherosclerosis, thereby supporting the atherogenicity of CETP and the inhibitory activity of garlic supplementation against CETP. PMID:12706483

  20. An Optimal CDS Construction Algorithm with Activity Scheduling in Ad Hoc Networks.

    PubMed

    Penumalli, Chakradhar; Palanichamy, Yogesh

    2015-01-01

    A new energy efficient optimal Connected Dominating Set (CDS) algorithm with activity scheduling for mobile ad hoc networks (MANETs) is proposed. This algorithm achieves energy efficiency by minimizing the Broadcast Storm Problem [BSP] and at the same time considering the node's remaining energy. The Connected Dominating Set is widely used as a virtual backbone or spine in mobile ad hoc networks [MANETs] or Wireless Sensor Networks [WSN]. The CDS of a graph representing a network has a significant impact on an efficient design of routing protocol in wireless networks. Here the CDS is a distributed algorithm with activity scheduling based on unit disk graph [UDG]. The node's mobility and residual energy (RE) are considered as parameters in the construction of stable optimal energy efficient CDS. The performance is evaluated at various node densities, various transmission ranges, and mobility rates. The theoretical analysis and simulation results of this algorithm are also presented which yield better results.

  1. Examining the link between framed physical activity ads and behavior among women.

    PubMed

    Berenbaum, Erin; Latimer-Cheung, Amy E

    2014-06-01

    Gain-framed messages are more effective at promoting physical activity than loss-framed messages. However, the mechanism through which this effect occurs is unclear. The current experiment examined the effects of message framing on variables described in the communication behavior change model (McGuire, 1989), as well as the mediating effects of these variables on the message-frame-behavior relationship. Sixty low-to-moderately active women viewed 20 gain- or loss-framed ads and five control ads while their eye movements were recorded via eye tracking. The gain-framed ads attracted greater attention, ps < .05; produced more positive attitudes, p = .06; were better recalled, p < .001; influenced decisions to be active, p = .07; and had an immediate and delayed impact on behavior, ps < .05, compared with the loss-framed messages. Mediation analyses failed to reveal any significant effects. This study demonstrates the effects of framed messages on several outcomes; however, the mechanisms underlying these effects remain unclear.

  2. Microwave-assisted extraction of polysaccharides from Yupingfeng powder and their antioxidant activity

    PubMed Central

    Wang, Dan; Zhang, Bi-Bo; Qu, Xiao-Xia; Gao, Feng; Yuan, Min-Yong

    2015-01-01

    Background: Microwave-assisted reflux extraction of polysaccharides YPF-P from the famous Chinese traditional drug, Yupingfeng powder, optimization of extracting conditions and evaluation of their antioxidant activity were conducted in this study. Results: Single factor effect trends were achieved through yields and contends of YPF-P obtained from different extracting conditions. Then through a three-level, four-variable Box-Behnken design of response surface methodology adopting yield as response, the optimal conditions were determined as follows: Material/solvent ratio 1:23.37, microwave power 560 W, Extraction temperature 64°C, and extraction time 9.62 min. Under the optimal conditions, the YPF-P extraction yield was 3.23%, and its content was detected as 38.52%. In antioxidant assays, the YPF-P was tested to possess 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activities with an IC50 value of 0.262 mg/ml. In addition, YPF-P was also proved to have relatively low ferric reducing antioxidant power (FRAP), compared to Vc, through FRAP assay. Conclusion: In the microwave assisted reflux extraction research, good YPF-P yield was achieved from materials with relatively low YPF-P content. And for the first time, both DPPH and FRAP assays were conducted on YPF-P, which proved that the antioxidant activity of YPF-P contributed to the functions of this medicine. PMID:26246730

  3. Effects of Drying Temperature on Antioxidant Activities of Tomato Powder and Storage Stability of Pork Patties

    PubMed Central

    2016-01-01

    This study was performed to evaluate the antioxidant activity of oven-dried tomato powder (OTP) as affected by drying temperature and the effect of OTP on the product quality of pork patties. Three OTP products were obtained by drying of fresh tomato at 60, 80 and 100℃ oven until constant weight was obtained. Total phenolic content of three kinds of OTPs ranged from 1.95 to 5.94 g/100 g. The highest amount of total phenolic compound was observed in OTP dried at 100℃. Antioxidant activity of three kinds of OTPs was measured by 1,1-diphenyl-2-pycrylhydrazyl (DPPH)-radical scavenging activity, iron chelating ability, reducing power and measurement of lipid peroxide in linoleic acid emulsion system. In all parameters, OTP at 100℃ showed the higher antioxidant activity than other temperatures (p<0.05). Based on the model study, the physicochemical properties, and antioxidant and antimicrobial activities of pork patties containing 1% OTP were measured. Redness of pork patties were increased with the addition of OTPs (p<0.05). Thiobarbituric acid reactive substances (TBARS) values of raw pork patties containing OTPs were lower than those of control (CTL) until 7 d of storage, regardless of drying temperatures (p<0.05). Peroxide values of pork patties made with OTP (1%) were lower than those of CTL until the end of storage time (p<0.05). However, no antimicrobial activities were observed among the treatments (p>0.05). Therefore, OTPs could be used as a natural antioxidant in meat products. PMID:27499664

  4. Effects of Drying Temperature on Antioxidant Activities of Tomato Powder and Storage Stability of Pork Patties.

    PubMed

    Kim, Hyeong Sang; Chin, Koo Bok

    2016-01-01

    This study was performed to evaluate the antioxidant activity of oven-dried tomato powder (OTP) as affected by drying temperature and the effect of OTP on the product quality of pork patties. Three OTP products were obtained by drying of fresh tomato at 60, 80 and 100℃ oven until constant weight was obtained. Total phenolic content of three kinds of OTPs ranged from 1.95 to 5.94 g/100 g. The highest amount of total phenolic compound was observed in OTP dried at 100℃. Antioxidant activity of three kinds of OTPs was measured by 1,1-diphenyl-2-pycrylhydrazyl (DPPH)-radical scavenging activity, iron chelating ability, reducing power and measurement of lipid peroxide in linoleic acid emulsion system. In all parameters, OTP at 100℃ showed the higher antioxidant activity than other temperatures (p<0.05). Based on the model study, the physicochemical properties, and antioxidant and antimicrobial activities of pork patties containing 1% OTP were measured. Redness of pork patties were increased with the addition of OTPs (p<0.05). Thiobarbituric acid reactive substances (TBARS) values of raw pork patties containing OTPs were lower than those of control (CTL) until 7 d of storage, regardless of drying temperatures (p<0.05). Peroxide values of pork patties made with OTP (1%) were lower than those of CTL until the end of storage time (p<0.05). However, no antimicrobial activities were observed among the treatments (p>0.05). Therefore, OTPs could be used as a natural antioxidant in meat products. PMID:27499664

  5. 78 FR 23951 - Powder River Regional Coal Team Activities: Notice of Public Meeting in Casper, Wyoming

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-23

    ... LBA II Tract is adjacent to the Spring Creek Mine located in Big Horn County, Montana. The RCT will... Data Adequacy Standards for the Powder River Coal Region. 6. Update on BLM land use planning efforts in... concern in the Powder River Coal Production Region. Any party interested in providing comments or...

  6. Cyclotron production of ``very high specific activity'' platinum radiotracers in No Carrier Added form

    NASA Astrophysics Data System (ADS)

    Birattari, C.; Bonardi, M.; Groppi, F.; Gini, L.; Gallorini, M.; Sabbioni, E.; Stroosnijder, M. F.

    2001-12-01

    At the "Radiochemistry Laboratory" of Accelerators and Applied Superconductivity Laboratory, LASA, several production and quality assurance methods for short-lived and high specific activity radionuclides, have been developed. Presently, the irradiations are carried out at the Scanditronix MC40 cyclotron (K=38; p, d, He-4 and He-3) of JRC-Ispra, Italy, of the European Community, while both chemical purity and specific activity determination are carried out at the TRIGA MARK II research reactor of University of Pavia and at LASA itself. In order to optimize the irradiation conditions for platinum radiotracer production, both thin- and thick-target excitation function of natOs(α,xn) nuclear reactions were measured. A very selective radiochemical separation to obtain Pt radiotracers in No Carrier Added form, has been developed. Both real specific activity and chemical purity of radiotracer, have been determined by neutron activation analysis and atomic absorption spectrometry. An Isotopic Dilution Factor (IDF) of the order of 50 is achieved.

  7. Performance of biological magnetic powdered activated carbon for drinking water purification.

    PubMed

    Lompe, Kim Maren; Menard, David; Barbeau, Benoit

    2016-06-01

    Combining the high adsorption capacity of powdered activated carbon (PAC) with magnetic properties of iron oxide nanoparticles (NPs) leads to a promising composite material, magnetic PAC or MPAC, which can be separated from water using magnetic separators. We propose MPAC as an alternative adsorbent in the biological hybrid membrane process and demonstrate that PAC covered with magnetic NPs is suitable as growth support for heterotrophic and nitrifying bacteria. MPAC with mass fractions of 0; 23; 38 and 54% maghemite was colonized in small bioreactors for over 90 days. Although the bacterial community composition (16s rRNA analysis) was different on MPAC compared to PAC, NPs neither inhibited dissolved organic carbon and ammonia biological removals nor contributed to significant adsorption of these compounds. The same amount of active heterotrophic biomass (48 μg C/cm(3)) developed on MPAC with a mass fraction of 54% NPs as on the non-magnetic PAC control. While X-ray diffraction confirmed that size and type of iron oxides did not change over the study period, a loss in magnetization between 10% and 34% was recorded. PMID:27017574

  8. Effect of particle size on antioxidant activity and catechin content of green tea powders.

    PubMed

    Zaiter, Ali; Becker, Loïc; Karam, Marie-Céleste; Dicko, Amadou

    2016-04-01

    This work evaluated the effect of grinding and sieving process of green tea leaves on particle size distribution and antioxidant activity. Granulometric classes ranging from 20 μm to 500 μm were studied. Hydroalcoholic extracts of green tea powders (GTPs) were analysed for total phenolic, total flavonoid, and catechin contents. The fraction of 100-180 μm ground at 6000 rpm showed the maximum catechin content with 33.5 mg/g dry matter (DM) and, the best antioxidant activity with IC50 values of 0.28 μg/mL and 0.13 μg/mL using DPPH and ABTS radical scavenging assays, respectively. However, antioxidant properties and catechin content decreased for particle of sizes less than 50 μm. Catechin content was higher for those ground at 6000 rpm as compared to at 18,000 rpm. The best grinding conditions and particle size were 6000 rpm and 100-180 μm.

  9. Adsorption of clofibric acid and ketoprofen onto powdered activated carbon: effect of natural organic matter.

    PubMed

    Gao, Yaohuan; Deshusses, Marc A

    2011-12-01

    The adsorption of two acidic pharmaceutically active compounds (PhACs), clofibric acid and ketoprofen, onto powdered activated carbon (PAC) was investigated with a particular focus on the influence of natural organic matter (NOM) on the adsorption of the PhACs. Suwannee River humic acids (SRHAs) were used as a substitute for NOM. Batch adsorption experiments were conducted to obtain adsorption kinetics and adsorption isotherms with and without SRHAs in the system. The adsorption isotherms and adsorption kinetics showed that the adsorption ofclofibric acid was not significantly affected by the presence of SRHAs at a concentration of 5 mg (as carbon) L(-1). An adsorption capacity of 70 to 140 mg g(-1) was observed and equilibrium was reached within 48 h. In contrast, the adsorption of ketoprofen was markedly decreased (from about 120 mg g(-1) to 70-100 mg g(-1)) in the presence of SRHAs. Higher initial concentrations of clofibric acid than ketoprofen during testing may explain the different behaviours that were observed. Also, the more hydrophobic ketoprofen molecules may have less affinity for PAC when humic acids (which are hydrophilic) are present. The possible intermolecular forces that could account for the different behaviour of clofibric acid and ketoprofen adsorption onto PAC are discussed. In particular, the relevance of electrostatic forces, electron donor-acceptor interaction, hydrogen bonding and London dispersion forces are discussed PMID:22439557

  10. Optimization of magnetic powdered activated carbon for aqueous Hg(II) removal and magnetic recovery.

    PubMed

    Faulconer, Emily K; von Reitzenstein, Natalia V Hoogesteijn; Mazyck, David W

    2012-01-15

    Activated carbon is known to adsorb aqueous Hg(II). MPAC (magnetic powdered activated carbon) has the potential to remove aqueous Hg to less than 0.2 μg/L while being magnetically recoverable. Magnetic recapture allows simple sorbent separation from the waste stream while an isolated waste potentially allows for mercury recycling. MPAC Hg-removal performance is verified by mercury mass balance, calculated by quantifying adsorbed, volatilized, and residual aqueous mercury. The batch reactor contained a sealed mercury-carbon contact chamber with mixing and constant N(2) (g) headspace flow to an oxidizing trap. Mercury adsorption was performed using spiked ultrapure water (100 μg/L Hg). Mercury concentrations were obtained using EPA method 245.1 and cold vapor atomic absorption spectroscopy. MPAC synthesis was optimized for Hg removal and sorbent recovery according to the variables: C:Fe, thermal oxidation temperature and time. The 3:1 C:Fe preserved most of the original sorbent surface area. As indicated by XRD patterns, thermal oxidation reduced the amorphous characteristic of the iron oxides but did not improve sorbent recovery and damaged porosity at higher oxidation temperatures. Therefore, the optimal synthesis variables, 3:1 C:Fe mass ratio without thermal oxidation, which can achieve 92.5% (± 8.3%) sorbent recovery and 96.3% (± 9%) Hg removal. The mass balance has been closed to within approximately ± 15%. PMID:22104766

  11. Isotope microscopy visualization of the adsorption profile of 2-methylisoborneol and geosmin in powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Sakamoto, Asuka; Nakao, Soichi; Taniguchi, Takuma; Matsushita, Taku; Shirasaki, Nobutaka; Sakamoto, Naoya; Yurimoto, Hisayoshi

    2014-09-16

    Decreasing the particle size of powdered activated carbon may enhance its equilibrium adsorption capacity for small molecules and micropollutants, such as 2-methylisoborneol (MIB) and geosmin, as well as for macromolecules and natural organic matter. Shell adsorption, in which adsorbates do not completely penetrate the adsorbent but instead preferentially adsorb near the outer surface of the adsorbent, may explain this enhancement in equilibrium adsorption capacity. Here, we used isotope microscopy and deuterium-doped MIB and geosmin to directly visualize the solid-phase adsorbate concentration profiles of MIB and geosmin in carbon particles. The deuterium/hydrogen ratio, which we used as an index of the solid-phase concentration of MIB and geosmin, was higher in the shell region than in the inner region of carbon particles. Solid-phase concentrations of MIB and geosmin obtained from the deuterium/hydrogen ratio roughly agreed with those predicted by shell adsorption model analyses of isotherm data. The direct visualization of the localization of micropollutant adsorbates in activated carbon particles provided direct evidence of shell adsorption. PMID:25162630

  12. Isotope microscopy visualization of the adsorption profile of 2-methylisoborneol and geosmin in powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Sakamoto, Asuka; Nakao, Soichi; Taniguchi, Takuma; Matsushita, Taku; Shirasaki, Nobutaka; Sakamoto, Naoya; Yurimoto, Hisayoshi

    2014-09-16

    Decreasing the particle size of powdered activated carbon may enhance its equilibrium adsorption capacity for small molecules and micropollutants, such as 2-methylisoborneol (MIB) and geosmin, as well as for macromolecules and natural organic matter. Shell adsorption, in which adsorbates do not completely penetrate the adsorbent but instead preferentially adsorb near the outer surface of the adsorbent, may explain this enhancement in equilibrium adsorption capacity. Here, we used isotope microscopy and deuterium-doped MIB and geosmin to directly visualize the solid-phase adsorbate concentration profiles of MIB and geosmin in carbon particles. The deuterium/hydrogen ratio, which we used as an index of the solid-phase concentration of MIB and geosmin, was higher in the shell region than in the inner region of carbon particles. Solid-phase concentrations of MIB and geosmin obtained from the deuterium/hydrogen ratio roughly agreed with those predicted by shell adsorption model analyses of isotherm data. The direct visualization of the localization of micropollutant adsorbates in activated carbon particles provided direct evidence of shell adsorption.

  13. Self-flocculated powdered activated carbon with different oxidation methods and their influence on adsorption behavior.

    PubMed

    Gong, Zailin; Li, Shujin; Ma, Jun; Zhang, Xiangdong

    2016-03-01

    The commercial powdered activated carbon (PAC) has been selectively oxidized by two methods. The two oxidized methods are wet oxidation with ammonium persulfate and thermal treatment after acidification with hydrochloride acid, respectively. The two oxidized PAC were then functionalized with thermoresponsive poly (N-isopropylacrylamide) (PNIPAM) in aqueous solution at ambient temperature. Comparing the two oxidized PAC products and their grafted derivatives, the oxidized PAC modified with thermal treatment after acidification shows larger surface area of 1184 m(2)/g and better adsorption of bisphenol A. Its derivative also exhibits relatively large surface area and adsorption capacity after grafted with PNIPAM. The maximum surface adsorption capacity simulated under Langmuir Models reached 156 mg/g. In addition, the grafted PAC products show self-flocculation behaviors with rapid response to temperature because of the thermal phase transition and entanglement behaviors of PNIPAM. The present study provides a new way to obtain carboxyl-rich activated carbon with large surface area and better adsorption capacity. The retrievable grafted PAC with good self-flocculation effect responsive to temperature will have high potential application in water remediation which requires pre-heating and emergency water treatment in the wild. PMID:26551226

  14. Performance of biological magnetic powdered activated carbon for drinking water purification.

    PubMed

    Lompe, Kim Maren; Menard, David; Barbeau, Benoit

    2016-06-01

    Combining the high adsorption capacity of powdered activated carbon (PAC) with magnetic properties of iron oxide nanoparticles (NPs) leads to a promising composite material, magnetic PAC or MPAC, which can be separated from water using magnetic separators. We propose MPAC as an alternative adsorbent in the biological hybrid membrane process and demonstrate that PAC covered with magnetic NPs is suitable as growth support for heterotrophic and nitrifying bacteria. MPAC with mass fractions of 0; 23; 38 and 54% maghemite was colonized in small bioreactors for over 90 days. Although the bacterial community composition (16s rRNA analysis) was different on MPAC compared to PAC, NPs neither inhibited dissolved organic carbon and ammonia biological removals nor contributed to significant adsorption of these compounds. The same amount of active heterotrophic biomass (48 μg C/cm(3)) developed on MPAC with a mass fraction of 54% NPs as on the non-magnetic PAC control. While X-ray diffraction confirmed that size and type of iron oxides did not change over the study period, a loss in magnetization between 10% and 34% was recorded.

  15. Odor active compounds content in spices and their microencapsulated powders measured by SPME.

    PubMed

    Wojtowicz, Elżbieta; Zawirska-Wojtasiak, Renata; Adamiec, Janusz; Wąsowicz, Erwin; Przygoński, Krzysztof; Remiszewski, Marian

    2010-10-01

    Within this study, main odorants of marjoram and thyme (linalool and thymol) were determined in spices and microencapsulated powders using solid-phase microextraction (SPME). Analyses were conducted on selected batches of spices before and after decontamination and on microencapsulated powders prepared for technological purposes (improvement of aroma in decontaminated spices). Conditions of SPME analyses were determined for individual compounds and matrices. Determination of total and surface contents of compounds and the percentage dependencies between encapsulated and surface aroma made it possible to identify the best powders in terms of their quality.

  16. Odor active compounds content in spices and their microencapsulated powders measured by SPME.

    PubMed

    Wojtowicz, Elżbieta; Zawirska-Wojtasiak, Renata; Adamiec, Janusz; Wąsowicz, Erwin; Przygoński, Krzysztof; Remiszewski, Marian

    2010-10-01

    Within this study, main odorants of marjoram and thyme (linalool and thymol) were determined in spices and microencapsulated powders using solid-phase microextraction (SPME). Analyses were conducted on selected batches of spices before and after decontamination and on microencapsulated powders prepared for technological purposes (improvement of aroma in decontaminated spices). Conditions of SPME analyses were determined for individual compounds and matrices. Determination of total and surface contents of compounds and the percentage dependencies between encapsulated and surface aroma made it possible to identify the best powders in terms of their quality. PMID:21535518

  17. Heightened hurricane activity on the Little Bahama Bank from 1350 to 1650 AD

    NASA Astrophysics Data System (ADS)

    van Hengstum, Peter J.; Donnelly, Jeffrey P.; Toomey, Michael R.; Albury, Nancy A.; Lane, Philip; Kakuk, Brian

    2014-09-01

    Deciphering how the climate system has controlled North Atlantic tropical cyclone activity through the Holocene will require a larger observational network of prehistoric hurricane activity. Problematically, the tropical North Atlantic is dominated by carbonate landscapes that typically preserve poorer quality coastal sediment records in comparison to their temperate-region counterparts (e.g., sedimentation continuity and rate). Coastal karst basins (CKBs), such as sinkholes, blueholes, and underwater caves, are widely distributed on carbonate platforms and contain overlooked sedimentary records. Here we present a millennium of hurricane deposits on the Little Bahama Bank archived in a 165 cm core that was extracted from 69 m below sea level in a bluehole on Great Abaco Island, The Bahamas. The coarse-grained overwash deposits associated with both hurricanes Jeanne (2004) and Floyd (1999) were identified using radioisotopes (137Cs, 14C, 210Pb), and indicate that the bluehole is sensitive to hurricane-induced sedimentation. Over the last millennium, the Little Bahama Bank experienced heightened hurricane activity from 1350 to 1650 AD. The simplest explanation for this active interval is that favorable climate conditions (El Niño, West African Monsoon, and sea surface temperatures) encouraged North Atlantic hurricane activity at that time. However, asynchronous hurricane activity at similar latitudes in the North Atlantic and Gulf of Mexico suggest that regional oceanography has modulated or amplified regional hurricane activity over the last millennium.

  18. Regeneration of spent powdered activated carbon saturated with inorganic ions by cavitation united with ion exchange method.

    PubMed

    Li, Gang; Gao, Hong; Li, Yansheng; Yang, Huixin

    2011-06-01

    Using ion exchange resin as transfer media, regenerate powdered activated carbon (PAC) adsorbed inorganic ions by cavitation to enhance the transfer; we studied how the regeneration time and the mass ratio of resin and PAC influence the regeneration rate respectively through re-adsorption. The result showed that the effective regeneration of PAC saturated with inorganic ions was above 90% using ion exchange resin as media and transfer carrier, the quantity of PAC did not reduced but activated in the process. PMID:25084579

  19. Powder Activated Carbon Pretreatment of a Microfiltration Membrane for the Treatment of Surface Water.

    PubMed

    Song, Yali; Dong, Bingzhi; Gao, Naiyun; Ma, Xiaoyan

    2015-09-01

    This study focused on the effect of powder activated carbon (PAC) adsorption on microfiltration (MF) membrane performance. The results showed that PAC pretreatment offered high organic matter removal rates for both dissolved organic carbon (DOC) and ultraviolet absorbance at 254 nm (UV254) during 10-200 mg/L PAC dosage. The removal efficiencies of organic matter by MF membrane filtration decreased with the increase of organic matter removal rate by PAC adsorption. PAC mainly removed organic matter of about 3 kDa molecular weight (MW). MF membrane maintained more than 5 kDa MW organic matter on the membrane after PAC adsorption. The results of membrane filtration indicated that PAC pretreatment slightly promoted membrane flux, regardless of PAC dosage. It seems that the organic matter fouling membrane was concentrated in more than 3 kDa MW. PAC removed markedly less than 3 kDa MW organic matter and had less effect on more than 3 kDa organic matter. Thus, PAC cannot reduce membrane fouling.

  20. Structural transformations in the a-tricalcium phosphate powders after mechanical activation and subsequent heat treatment

    NASA Astrophysics Data System (ADS)

    Shamray, V. F.; Karpihin, A. E.; Fedotov, A. Y.; Komlev, V. S.; Barinov, S. M.; Sirotinkin, V. P.

    2016-04-01

    X-ray diffraction analysis of the structural phase evolution in the a-TCP powder subjected to milling in the planetary mill in butanol, and followed by annealing at 1300 °C was performed. After milling, there was a systematic smoothing of the X-ray diffraction pattern of α-TCP. Significant changes in lattice constants and atomic parameters were not observed. The average particle size was reduced from 10 to 2 micrometers. The decrease of the size of coherently scattering domains CSD (250 to 80 nm) makes the main contribution to the X-ray lines broadening. The value of microstrain changes from 1 *10-6 to 2*10-4. After annealing at 1300 °C for 2 hours the phase with apatite structure was found. The content of the apatite phase increases with increasing of time of mechanical activation. Possible mechanisms of deformation of α-TCP particles and structural transformations α-TCP → HA are considered.

  1. Thermal removal of mercury in spent powdered activated carbon from TOXECON process

    SciTech Connect

    Okwadha, G.D.O.; Li, J.; Ramme, B.; Kollakowsky, D.; Michaud, D.

    2009-10-15

    This research developed and demonstrated a technology to liberate Hg adsorbed onto powdered activated carbon (PAC) by the TOXECON process using pilot-scale high temperature air slide (HTAS) and bench-scale thermogravimetric analyzer (TGA). The HTAS removed 65, 83, and 92% of Hg captured with PAC when ran at 900{sup o}F, 1,000{sup o}F, and 1,200 {sup o}F, respectively, while the TGA removed 46 and 100% of Hg at 800 {sup o}F and 900{sup o}F, respectively. However, addition of CuO-Fe{sub 2}O{sub 3} mixture and CuCl catalysts enhanced Hg removal and PAC regeneration at lower temperatures. CuO-Fe{sub 2}O{sub 3} mixture performed better than CuCl in PAC regeneration. Scanning electron microscopy images and energy dispersive X-ray analysis show no change in PAC particle aggregation or chemical composition. Thermally treated sorbents had higher surface area and pore volume than the untreated samples indicating regeneration. The optimum temperature for PAC regeneration in the HTAS was 1,000{sup o}F. At this temperature, the regenerated sorbent had sufficient adsorption capacity similar to its virgin counterpart at 33.9% loss on ignition. Consequently, the regenerated PAC may be recycled back into the system by blending it with virgin PAC.

  2. Pretreatment with alum or powdered activated carbon reduces bacterial predation-associated irreversible fouling of membranes.

    PubMed

    Kim, Eun-Ho; Dwidar, Mohammed; Kwon, Young-Nam; Mitchell, Robert J

    2014-01-01

    This study evaluated the co-application of bacterial predation by Bdellovibrio bacteriovorus and either alum coagulation or powdered activated carbon adsorption to reduce fouling caused by Escherichia coli rich feed solutions in dead-end microfiltration tests. The flux increased when the samples were predated upon or treated with 100 ppm alum or PAC, but co-treatment with alum and predation gave the best flux results. The total membrane resistance caused by the predated sample was reduced six-fold when treated with 100 ppm PAC, from 11.8 to 1.98 × 10(11) m(-1), while irreversible fouling (Rp) was 2.7-fold lower. Treatment with 100 ppm alum reduced the total resistance 14.9-fold (11.8 to 0.79 × 10(11) m(-1)) while the Rp decreased 4.25-fold. SEM imaging confirmed this, with less obvious fouling of the membrane after the combined process. This study illustrates that the combination of bacterial predation and the subsequent removal of debris using coagulation or adsorption mitigates membrane biofouling and improves membrane performance. PMID:25410737

  3. Integrating powdered activated carbon into wastewater tertiary filter for micro-pollutant removal.

    PubMed

    Hu, Jingyi; Aarts, Annelies; Shang, Ran; Heijman, Bas; Rietveld, Luuk

    2016-07-15

    Integrating powdered activated carbon (PAC) into wastewater tertiary treatment is a promising technology to reduce organic micro-pollutant (OMP) discharge into the receiving waters. To take advantage of the existing tertiary filter, PAC was pre-embedded inside the filter bed acting as a fixed-bed adsorber. The pre-embedding (i.e. immobilization) of PAC was realized by direct dosing a PAC solution on the filter top, which was then promoted to penetrate into the filter media by a down-flow of tap water. In order to examine the effectiveness of this PAC pre-embedded filter towards OMP removal, batch adsorption tests, representing PAC contact reactor (with the same PAC mass-to-treated water volume ratio as in the PAC pre-embedded filter) were performed as references. Moreover, as a conventional dosing option, PAC was dosed continuously with the filter influent (i.e. the wastewater secondary effluent with the investigated OMPs). Comparative results confirmed a higher OMP removal efficiency associated with the PAC pre-embedded filter, as compared to the batch system with a practical PAC residence time. Furthermore, over a filtration period of 10 h (approximating a realistic filtration cycle for tertiary filters), the continuous dosing approach resulted in less OMP removal. Therefore, it was concluded that the pre-embedding approach can be preferentially considered when integrating PAC into the wastewater tertiary treatment for OMP elimination. PMID:27082256

  4. Powder Activated Carbon Pretreatment of a Microfiltration Membrane for the Treatment of Surface Water

    PubMed Central

    Song, Yali; Dong, Bingzhi; Gao, Naiyun; Ma, Xiaoyan

    2015-01-01

    This study focused on the effect of powder activated carbon (PAC) adsorption on microfiltration (MF) membrane performance. The results showed that PAC pretreatment offered high organic matter removal rates for both dissolved organic carbon (DOC) and ultraviolet absorbance at 254 nm (UV254) during 10–200 mg/L PAC dosage. The removal efficiencies of organic matter by MF membrane filtration decreased with the increase of organic matter removal rate by PAC adsorption. PAC mainly removed organic matter of about 3 kDa molecular weight (MW). MF membrane maintained more than 5 kDa MW organic matter on the membrane after PAC adsorption. The results of membrane filtration indicated that PAC pretreatment slightly promoted membrane flux, regardless of PAC dosage. It seems that the organic matter fouling membrane was concentrated in more than 3 kDa MW. PAC removed markedly less than 3 kDa MW organic matter and had less effect on more than 3 kDa organic matter. Thus, PAC cannot reduce membrane fouling. PMID:26378552

  5. How to dose powdered activated carbon in deep bed filtration for efficient micropollutant removal.

    PubMed

    Altmann, Johannes; Ruhl, Aki S; Sauter, Daniel; Pohl, Julia; Jekel, Martin

    2015-07-01

    Direct addition of powdered activated carbon (PAC) to the inlet of a deep bed filter represents an energy- and space-saving option to remove organic micropollutants (OMPs) during advanced wastewater treatment or drinking water purification. In this lab-scale study, continuous dosing, preconditioning a filter with PAC and combinations thereof were investigated as possible dosing modes with respect to OMP adsorption efficiency. Continuous dosing resulted in decreasing effluent concentrations with increasing filter runtime due to adsorption onto accumulating PAC in the filter bed. Approximately constant removal levels were achieved at longer filter runtimes, which were mainly determined by the dose of fresh PAC, rather than the total PAC amount embedded. The highest effluent concentrations were observed during the initial filtration stage. Meanwhile, preconditioning led to complete OMP adsorption at the beginning of filtration and subsequent gradual OMP breakthrough. PAC distribution in the pumice filter was determined by the loss on ignition of PAC and pumice and was shown to be relevant for adsorption efficiency. Preconditioning with turbulent upflow led to a homogenous PAC distribution and improved OMP adsorption significantly. Combining partial preconditioning and continuous dosing led to low initial effluent concentrations, but ultimately achieved concentrations similar to filter runs without preconditioning. Furthermore, a dosing stop prior to the end of filtration was suitable to increase PAC efficiency without affecting overall OMP removals. PMID:25898248

  6. Adsorption of ammonium dinitramide (ADN) from aqueous solutions. 1. Adsorption on powdered activated charcoal.

    PubMed

    Santhosh, G; Venkatachalam, S; Ninan, K N; Sadhana, R; Alwan, S; Abarna, V; Joseph, M A

    2003-03-17

    Investigations on the adsorption of ammonium dinitramide (NH(4)N(NO(2))(2)) (ADN) from aqueous solutions on powdered activated charcoal (PAC) were carried out in order to find out an effective and easier method of separating ADN from aqueous solutions. The effectiveness of PAC in the selective adsorption of ADN from aqueous solutions of ADN (ADN-F) and ADN in presence of sulfate (SO(4)(2-)) and nitrate (NO(3)(-)) ions (ADN-PS) was examined and compared using batch and column methods. The adsorption process follows both Langmuir and Freundlich adsorption isotherms and the isotherm parameters for the models were determined. The observed data favor the formation of monolayer adsorption. The adsorption capacities were found to be 63.3, 119, 105.3 and 82 mg of ADN per g of PAC for ADN-F (batch), ADN-PS (batch), ADN-F (column) and ADN-PS (column), respectively. Break-through curves for ADN-F and ADN-PS were obtained for the optimization of separation of ADN from aqueous solutions. Elution curves were generated for the desorption of ADN from PAC using hot water as eluent.

  7. Flux enhancement with powdered activated carbon addition in the membrane anaerobic bioreactor

    SciTech Connect

    Park, H.; Choo, K.H.; Lee, C.H.

    1999-10-01

    The effect of powdered activated carbon (PAC) addition on the performance of a membrane-coupled anaerobic bioreactor (MCAB) was investigated in terms of membrane filterability and treatability through a series of batch and continuous microfiltration (MF) experiments. In both batch and continuous MF of the digestion broth, a flux improvement with PAC addition was achieved, especially when a higher shear rate and/or a higher PAC dose were applied. Both the fouling and cake layer resistances decreased continuously with increasing the PAC dose up to 5 g/L. PAC played an important role in substantially reducing the biomass cake resistance due to its incompressible nature and higher backtransport velocities. PAC might have a scouring effect for removing the deposited biomass cake from the membrane surface while sorbing and/or coagulating dissolved organics and colloidal particles in the broth. The chemical oxygen demand and color in the effluent were much removed with PAC addition, and the system was also more stable against shock loading.

  8. Pilot-scale study of powdered activated carbon recirculation for micropollutant removal.

    PubMed

    Meinel, F; Sperlich, A; Jekel, M

    2016-01-01

    Adsorption onto powdered activated carbon (PAC) is a promising technique for the removal of organic micropollutants (OMPs) from treated wastewater. To enhance the adsorption efficiency, PAC is recycled back into the adsorption stage. This technique was examined in pilot scale in comparison to a reference without recirculation. Coagulation with Fe(3+) was carried out simultaneously to adsorption. Extensive OMP measurements showed that recirculation significantly increased OMP eliminations. Thus, significant PAC savings were feasible. The PAC concentration in the contact reactor proved to be an important operating parameter that can be surrogated by the easily measurable total suspended solids (TSS) concentration. OMP eliminations increased with increasing TSS concentrations. At 20 mg PAC L(-1) and 2.8 g TSS L(-1) in the contact reactor, well-adsorbable carbamazepine was eliminated by 97%, moderately adsorbable diclofenac was eliminated by 92% and poorly-adsorbable acesulfame was eliminated by 54% in comparison to 49%, 35% and 18%, respectively, without recirculation. The recirculation system represents an efficient technique, as the PAC's adsorption capacity is practically completely used. Small PAC dosages yield high OMP eliminations. Poorly-adsorbable gabapentin was eliminated to an unexpectedly high degree. A laboratory-scale biomass inhibition study showed that aerobic biodegradation removed gabapentin in addition to adsorption. PMID:27533867

  9. Desorption kinetics of benzene in a sandy soil in the presence of powdered activated carbon.

    PubMed

    Choi, J-W; Kim, S-B; Kim, D-J

    2007-02-01

    Desorption kinetics of benzene was investigated with a modified biphasic desorption model in a sandy soil with five different powdered activated carbon (PAC) contents (0, 1, 2, 5, 10% w/w) as sorbents. Sorption experiments followed by series dilution desorption were conducted for each sorbent. Desorption of benzene was successively performed at two stages using deionized water and hexane. Modeling was performed on both desorption isotherm and desorption rate for water-induced desorption to elucidate the presence of sorption-desorption hysteresis and biphasic desorption and if present to quantify the desorption-resistant fraction (q (irr)) and labile fraction (F) of desorption site responsible for rapid process. Desorption isotherms revealed that sorption-desorption exhibited a severe hysteresis with a significant fraction of benzene being irreversibly adsorbed onto both pure sand and PAC, and that desorption-resistant fraction (q (irr)) increased with PAC content. Desorption kinetic modeling showed that desorption of benzene was biphasic with much higher (4-40 times) rate constant for rapid process (k (1)) than that for slow process (k (2)), and that the difference in the rate constant increased with PAC content. The labile fraction (F) of desorption site showed a decreasing tendency with PAC. The experimental results would provide valuable information on remediation methods for soils and groundwater contaminated with BTEX.

  10. Osteogenic activity of nanonized pearl powder/poly (lactide-co-glycolide) composite scaffolds for bone tissue engineering.

    PubMed

    Yang, Yueh-Lung; Chang, Ching-Hsien; Huang, Ching-Cheng; Kao, Wenny Mei-Wen; Liu, Wei-Chung; Liu, Hsia-Wei

    2014-01-01

    Numerous materials have been proposed for bone tissue engineering. In this study, a newly designed hybrid composite scaffold composed of poly (D,L-lactide-co-glycolide) and a naturally bioceramic hybrid material, nanonized pearl powder, were prepared and the biological activities and physical properties of the scaffold for bone tissue engineering were evaluated. It is a composite consisting calcium carbonate crystal in an aragonite structure, embedded in an organic matrix. Peral contains one or more signal molecules capable of stimulating bone formation. The nanonized pearl powder is considered as a promising osteoinductive biomaterial. This biomaterial is biocompatible and shows osteogenic activity. In this study, the designed biohybrid of nanonized pearl powder/poly (lactide-co-glycolide) (NPP/PLGA) biocomposite scaffolds would employ biodegradable material as MC3T3-E1 cells seeded scaffolds. Therefore, the biocomposite scaffolds would be used to culture with MC3T3-E1 cells under spinner bioreactor in vitro. Furthermore, it also detailed how these tissues were characterized, qualitatively and quantitatively, with scanning electron microscopy and biochemical testing. The identity and the mode of action of these molecules on the osteoblast differentiation were analyzed. This study indicates that the efficiency of nanonized pearl powders in bone cell differentiation are certainly different from that of proteins. Further sudy will look forward to manufacturing the promising new generation bone substitute, three dimensional biocomposite scaffolds to replace the implant and autogeneous bone graft, which combines basic research and clinical application. PMID:24211987

  11. Quality characteristics of pork burger added with albedo-fiber powder obtained from yellow passion fruit (Passiflora edulis var. flavicarpa) co-products.

    PubMed

    López-Vargas, Jairo H; Fernández-López, Juana; Pérez-Álvarez, José Ángel; Viuda-Martos, Manuel

    2014-06-01

    The aim of this work determined the technological, nutritional and sensory characteristics of pork burgers, added with different concentrations (2.5 and 5%) of passion fruit albedo (PFA) co-product, obtained from passion fruit juice processing. The addition of PFA on pork burgers improves their nutritional value (higher fiber content). In raw and cooked burger, all textural parameters, except springiness and cohesiveness, were affected by the incorporation of PFA. PFA addition was found to be effective improving the cooking yield, moisture retention and fat retention. The raw and cooked pork burgers added with PFA had lower TBA values and lower counts of aerobic mesophilic bacteria and enterobacteria than the control samples. No Escherichia coli and molds were found in the samples. The overall acceptability scores showed that the most appreciated sample was the one containing 2.5% PFA. According to the results obtained, 2.5 and 5% of PFA addition can be recommended in pork burger production as a new dietary fiber source.

  12. Quality characteristics of pork burger added with albedo-fiber powder obtained from yellow passion fruit (Passiflora edulis var. flavicarpa) co-products.

    PubMed

    López-Vargas, Jairo H; Fernández-López, Juana; Pérez-Álvarez, José Ángel; Viuda-Martos, Manuel

    2014-06-01

    The aim of this work determined the technological, nutritional and sensory characteristics of pork burgers, added with different concentrations (2.5 and 5%) of passion fruit albedo (PFA) co-product, obtained from passion fruit juice processing. The addition of PFA on pork burgers improves their nutritional value (higher fiber content). In raw and cooked burger, all textural parameters, except springiness and cohesiveness, were affected by the incorporation of PFA. PFA addition was found to be effective improving the cooking yield, moisture retention and fat retention. The raw and cooked pork burgers added with PFA had lower TBA values and lower counts of aerobic mesophilic bacteria and enterobacteria than the control samples. No Escherichia coli and molds were found in the samples. The overall acceptability scores showed that the most appreciated sample was the one containing 2.5% PFA. According to the results obtained, 2.5 and 5% of PFA addition can be recommended in pork burger production as a new dietary fiber source. PMID:24607997

  13. Adding multiple micronutrient powders to a homestead food production programme yields marginally significant benefit on anaemia reduction among young children in Nepal.

    PubMed

    Osei, Akoto K; Pandey, Pooja; Spiro, David; Adhikari, Debendra; Haselow, Nancy; De Morais, Caroline; Davis, Dale

    2015-12-01

    Anaemia affects 46% of preschool-aged children in Nepal. A cluster-randomised study was conducted in rural Nepal to test whether providing micronutrient powders (MNP) in addition to enhanced homestead food production (EHFP) programme, consisting of home gardens, poultry and nutrition education, could lead to a higher reduction in anaemia compared with providing only EHFP. This sub-study enrolled 335 children aged 6-9 months into one of three groups: (1) EHFP + MNP; (2) EHFP; or (3) control. The EHFP + MNP group received 60 sachets of MNP for flexible consumption at the start and 6 months later for a total supplementation period of 11 months. The MNP contained 15 micronutrients including iron (10 mg encapsulated ferrous fumarate). Haemoglobin and anthropometry were measured at baseline and post-MNP supplementation. Mean ± SE haemoglobin concentration increased significantly in all groups, with a slightly higher but non-significant increase in the EHFP + MNP and EHFP compared with control (difference-in-differences: 4.1 g L(-1) for EHFP + MNP vs. control; 3.6 g L(-1) for EHFP vs. control; 0.5 g L(-1) for EHFP + MNP vs. EHFP). Anaemia decreased at a slightly higher magnitude in the EHFP + MNP [51.5 percentage points (PP)] than the EHFP (48.6 PP) and control (39.6 PP), with adjusted odds ratios (95% CI) at post-supplementation of 0.52 (0.25-1.12) for EHFP + MNP and 0.69 (0.35-1.36) for EHFP, compared with control. There was no impact on child growth. Combining EHFP and MNP programmes yielded a marginally significant reduction in anaemia among children. PMID:25682798

  14. Adding multiple micronutrient powders to a homestead food production programme yields marginally significant benefit on anaemia reduction among young children in Nepal.

    PubMed

    Osei, Akoto K; Pandey, Pooja; Spiro, David; Adhikari, Debendra; Haselow, Nancy; De Morais, Caroline; Davis, Dale

    2015-12-01

    Anaemia affects 46% of preschool-aged children in Nepal. A cluster-randomised study was conducted in rural Nepal to test whether providing micronutrient powders (MNP) in addition to enhanced homestead food production (EHFP) programme, consisting of home gardens, poultry and nutrition education, could lead to a higher reduction in anaemia compared with providing only EHFP. This sub-study enrolled 335 children aged 6-9 months into one of three groups: (1) EHFP + MNP; (2) EHFP; or (3) control. The EHFP + MNP group received 60 sachets of MNP for flexible consumption at the start and 6 months later for a total supplementation period of 11 months. The MNP contained 15 micronutrients including iron (10 mg encapsulated ferrous fumarate). Haemoglobin and anthropometry were measured at baseline and post-MNP supplementation. Mean ± SE haemoglobin concentration increased significantly in all groups, with a slightly higher but non-significant increase in the EHFP + MNP and EHFP compared with control (difference-in-differences: 4.1 g L(-1) for EHFP + MNP vs. control; 3.6 g L(-1) for EHFP vs. control; 0.5 g L(-1) for EHFP + MNP vs. EHFP). Anaemia decreased at a slightly higher magnitude in the EHFP + MNP [51.5 percentage points (PP)] than the EHFP (48.6 PP) and control (39.6 PP), with adjusted odds ratios (95% CI) at post-supplementation of 0.52 (0.25-1.12) for EHFP + MNP and 0.69 (0.35-1.36) for EHFP, compared with control. There was no impact on child growth. Combining EHFP and MNP programmes yielded a marginally significant reduction in anaemia among children.

  15. Extension of the Optical Absorption Range in Zn-Doped MgO Powders and Its Effect on Antibacterial Activity

    NASA Astrophysics Data System (ADS)

    Ohira, Toshiaki; Kawamura, Mari; Fukuda, Masayuki; Alvarez, Kelly; Özkal, Burak; Yamamoto, Osamu

    2010-04-01

    In order to produce powder samples of Zn-doped MgO, the precursors, MgO and ZnO, were mixed in a molar ratio higher than 1.86 and subsequently treated at 1200 °C for 5 h in air atmosphere. With increasing Zn content in MgO, the lattice constant increased linearly, and the optical absorption intensity increased in the wavelength ranging from 200 to 400 nm. Antibacterial activity of the obtained powder samples was examined by colony count method using Escherichia coli and Staphylococcus aureus. In the antibacterial tests, it was found that the antibacterial activity enhanced with increasing Zn content in MgO. Antibacterial action toward S. aureus was greater than that toward E. coli, irrespective of the Zn content in MgO. From these results, the enhancement of the antibacterial activity could be related with the optical absorption of Zn-doped MgO.

  16. [Determination of mercury and copper in water samples by activation analysis using preconcentration on emission spectroscopic carbon powder (author's transl)].

    PubMed

    Nagatsuka, S; Tanizaki, Y

    1978-07-01

    A simple preconcentration procedure for mercury and copper was examined in the activation analysis of water samples. The preconcentration using pure activated carbon has been reported in several papers. The authors found that the carbon powder for emission spectroscopic analysis showed the high purity equivalent to pure activated carbon. The influence of various parameters in adsorption conditions was studied by radioactive tracers 197Hg and 64Cu. It was confirmed that 100% of these elements were adsorbed on carbon powders as pyrrolidine dithiocarbonate complexes at an acidity of pH 6--8, the temperature of 50 degrees C and the stirring time of 30 minutes. This method was applied to the activation analysis of the river water samples taken from the upper stream area of the Arakawa river and the ground water samples taken from the upper stream area of the Arakawa river and the ground water samples taken from the wells of the environs of Tokyo Megapolis. The carbon powders which adsorbed these elements were filtered, dried and analyzed by instrumental neutron activation analysis. The Hg concentrations of 0.01--0.1 ppb in river water and 0.03--1.4 ppb in ground water were obtained as well as the Cu concentrations of 0.3--3.0 ppb in ground water. The limits of determination of this method are 0.01 ppb Hg and 0.2 ppb Cu in the case of 11 sample of fresh water. PMID:704956

  17. Adsorption of N-nitrosodimethylamine precursors by powdered and granular activated carbon.

    PubMed

    Hanigan, David; Zhang, Jinwei; Herckes, Pierre; Krasner, Stuart W; Chen, Chao; Westerhoff, Paul

    2012-11-20

    Activated carbon (AC) has been shown to remove precursors of halogenated disinfection byproducts. Granular and powdered activated carbon (GAC, PAC) were investigated for their potential to adsorb N-nitrosodimethylamine (NDMA) precursors from blends of river water and effluent from a wastewater treatment plant (WWTP). At bench scale, waters were exposed to lignite or bituminous AC, either as PAC in bottle point experiments or as GAC in rapid small-scale column tests (RSSCTs). NDMA formation potential (FP) was used as a surrogate for precursor removal. NDMA FP was reduced by 37, 59, and 91% with 3, 8, and 75 mg/L of one PAC, respectively, with a 4-h contact time. In RSSCTs and in full-scale GAC contactors, NDMA FP removal always exceeded that of the bulk dissolved organic carbon (DOC) and UV absorbance at 254 nm. For example, whereas DOC breakthrough exceeded 90% of its influent concentration after 10,000 bed volumes of operation in an RSSCT, NDMA FP was less than 40% of influent concentration after the same bed life of the GAC. At full or pilot scale, high NDMA FP reduction ranging from >60 to >90% was achieved across GAC contactors, dependent upon the GAC bed life and/or use of a preoxidant (chlorine or ozone). In all experiments, NDMA formation was not reduced to zero, which suggests that although some precursors are strongly sorbed, others are not. This is among the first studies to show that AC is capable of adsorbing NDMA precursors, but further research is needed to better understand NDMA precursor chemical properties (e.g., hydrophobicity, molecular size) and evaluate how best to incorporate this finding into full-scale designs and practice.

  18. Removal of N-nitrosodimethylamine precursors with powdered activated carbon adsorption.

    PubMed

    Beita-Sandí, Wilson; Ersan, Mahmut Selim; Uzun, Habibullah; Karanfil, Tanju

    2016-01-01

    The main objective of this study was to examine the roles of powdered activated carbon (PAC) characteristics (i.e., surface chemistry, pore size distribution, and surface area) in the removal of N-nitrosodimethylamine (NDMA) formation potential (FP) in surface and wastewater-impacted waters. Also, the effects of natural attenuation of NDMA precursors in surface waters, NDMA FP concentration, and carbon dose on the removal of NDMA FP by PAC were evaluated. Finally, the removal of NDMA FP by PAC at two full-scale DWTPs was monitored. Wastewater-impacted and surface water samples were collected to conduct adsorption experiments using different PACs and activated carbon fibers (ACFs) with a wide range of physicochemical characteristics. The removal efficiency of NDMA FP by PAC was significantly higher in wastewater-impacted than surface waters. Adsorbable NDMA precursors showed a size distribution in the waters tested; the adsorbable fraction included precursors accessing the pore size regions of 10-20 Å and <10 Å. Basic carbons showed higher removal of NDMA FP than acidic carbons on a surface area basis. The overall removal of NDMA FP by PAC on a mass basis depended on the surface area, pore size distribution and pHPZC. Thus, PACs with hybrid characteristics (micro and mesoporous), higher surface areas, and basic surface chemistry are more likely to be effective for NDMA precursor control by PAC adsorption. The application of PAC in DWTPs for taste and odor control resulted in an additional 20% removal of NDMA FP for the PAC doses of 7-10 mg/L. The natural attenuation of NDMA precursors through a combination of processes (biodegradation, photolysis and adsorption) decreased their adsorbability and removal by PAC adsorption.

  19. Adsorption of N-nitrosodimethylamine precursors by powdered and granular activated carbon.

    PubMed

    Hanigan, David; Zhang, Jinwei; Herckes, Pierre; Krasner, Stuart W; Chen, Chao; Westerhoff, Paul

    2012-11-20

    Activated carbon (AC) has been shown to remove precursors of halogenated disinfection byproducts. Granular and powdered activated carbon (GAC, PAC) were investigated for their potential to adsorb N-nitrosodimethylamine (NDMA) precursors from blends of river water and effluent from a wastewater treatment plant (WWTP). At bench scale, waters were exposed to lignite or bituminous AC, either as PAC in bottle point experiments or as GAC in rapid small-scale column tests (RSSCTs). NDMA formation potential (FP) was used as a surrogate for precursor removal. NDMA FP was reduced by 37, 59, and 91% with 3, 8, and 75 mg/L of one PAC, respectively, with a 4-h contact time. In RSSCTs and in full-scale GAC contactors, NDMA FP removal always exceeded that of the bulk dissolved organic carbon (DOC) and UV absorbance at 254 nm. For example, whereas DOC breakthrough exceeded 90% of its influent concentration after 10,000 bed volumes of operation in an RSSCT, NDMA FP was less than 40% of influent concentration after the same bed life of the GAC. At full or pilot scale, high NDMA FP reduction ranging from >60 to >90% was achieved across GAC contactors, dependent upon the GAC bed life and/or use of a preoxidant (chlorine or ozone). In all experiments, NDMA formation was not reduced to zero, which suggests that although some precursors are strongly sorbed, others are not. This is among the first studies to show that AC is capable of adsorbing NDMA precursors, but further research is needed to better understand NDMA precursor chemical properties (e.g., hydrophobicity, molecular size) and evaluate how best to incorporate this finding into full-scale designs and practice. PMID:23106335

  20. Removal of N-nitrosodimethylamine precursors with powdered activated carbon adsorption.

    PubMed

    Beita-Sandí, Wilson; Ersan, Mahmut Selim; Uzun, Habibullah; Karanfil, Tanju

    2016-01-01

    The main objective of this study was to examine the roles of powdered activated carbon (PAC) characteristics (i.e., surface chemistry, pore size distribution, and surface area) in the removal of N-nitrosodimethylamine (NDMA) formation potential (FP) in surface and wastewater-impacted waters. Also, the effects of natural attenuation of NDMA precursors in surface waters, NDMA FP concentration, and carbon dose on the removal of NDMA FP by PAC were evaluated. Finally, the removal of NDMA FP by PAC at two full-scale DWTPs was monitored. Wastewater-impacted and surface water samples were collected to conduct adsorption experiments using different PACs and activated carbon fibers (ACFs) with a wide range of physicochemical characteristics. The removal efficiency of NDMA FP by PAC was significantly higher in wastewater-impacted than surface waters. Adsorbable NDMA precursors showed a size distribution in the waters tested; the adsorbable fraction included precursors accessing the pore size regions of 10-20 Å and <10 Å. Basic carbons showed higher removal of NDMA FP than acidic carbons on a surface area basis. The overall removal of NDMA FP by PAC on a mass basis depended on the surface area, pore size distribution and pHPZC. Thus, PACs with hybrid characteristics (micro and mesoporous), higher surface areas, and basic surface chemistry are more likely to be effective for NDMA precursor control by PAC adsorption. The application of PAC in DWTPs for taste and odor control resulted in an additional 20% removal of NDMA FP for the PAC doses of 7-10 mg/L. The natural attenuation of NDMA precursors through a combination of processes (biodegradation, photolysis and adsorption) decreased their adsorbability and removal by PAC adsorption. PMID:26584342

  1. Predicting trace organic compound attenuation with spectroscopic parameters in powdered activated carbon processes.

    PubMed

    Ziska, Austin D; Park, Minkyu; Anumol, Tarun; Snyder, Shane A

    2016-08-01

    The removal of trace organic compounds (TOrCs) is of growing interest in water research and society. Powdered activated carbon (PAC) has been proven to be an effective method of removal for TOrCs in water, with the degree of effectiveness depending on dosage, contact time, and activated carbon type. In this study, the attenuation of TOrCs in three different secondary wastewater effluents using four PAC materials was studied in order to elucidate the effectiveness and efficacy of PAC for TOrC removal. With the notable exception of hydrochlorothiazide, all 14 TOrC indicators tested in this study exhibited a positive correlation of removal rate with their log Dow values, demonstrating that the main adsorption mechanism was hydrophobic interaction. As a predictive model, the modified Chick-Watson model, often used for the prediction of microorganism inactivation by disinfectants, was applied. The applied model exhibited good predictive power for TOrC attenuation by PAC in wastewater. In addition, surrogate models based upon spectroscopic measurements including UV absorbance at 254 nm and total fluorescence were applied to predict TOrC removal by PAC. The surrogate model was found to provide an excellent prediction of TOrC attenuation for all combinations of water quality and PAC type included in this study. The success of spectrometric parameters as surrogates in predicting TOrC attenuation by PAC are particularly useful because of their potential application in real-time on-line sensor monitoring and process control at full-scale water treatment plants, which could lead to significantly reduced operator response times and PAC operational optimization. PMID:27174829

  2. Chemisorption of Perfluorooctanoic Acid on Powdered Activated Carbon Initiated by Persulfate in Aqueous Solution.

    PubMed

    Sun, Bo; Ma, Jun; Sedlak, David L

    2016-07-19

    Perfluorooctanoic acid (PFOA) is a perfluorocarboxylic acid that is difficult to treat by most conventional methods. As a result, it is often removed from solution by adsorption on powdered activated carbon (PAC), followed by incineration of the spent carbon. To provide a new approach for treatment, PFOA was exposed to sulfate radicals (SO4(-•)) produced by thermolysis of persulfate (S2O8(2-)) in the presence of PAC. Under acidic conditions, thermal activation of persulfate resulted in transformation of PFOA to shorter-chain-length perfluorinated compounds, as previously reported. However, when thermolysis of persulfate occurred under circumneutral pH conditions in the presence of PAC, a new removal pathway for PFOA was observed. Under these conditions, the removal of PFOA was attributable to chemisorption, a process in which PAC catalyzed persulfate decomposition and reacted with the transformation products to produce covalently bound PFOA. At PAC concentrations between 200 and 1000 mg/L and an initial PFOA concentration of 0.5 μM, covalent bonding resulted in removal of 10-40% of the PFOA. Under these conditions, the process resulted in removal of more than half of a more hydrophilic perfluoroalkyl acid (i.e., perfluorobutanoic acid, PFBA), which was greater than the amount of PFBA removed by physical adsorption on PAC. Although the high reaction temperatures (i.e., 80 °C) and relatively high doses of PAC used in this study may be impractical for drinking water treatment, this process may be applied to the treatment of these recalcitrant compounds in industrial wastewater, reverse osmosis concentrate, and other waters that contain high concentrations of PFOA and other perfluorocarboxylic acids. PMID:27336204

  3. Sampling and major element chemistry of the recent (A.D. 1631-1944) Vesuvius activity

    USGS Publications Warehouse

    Belkin, H.E.; Kilburn, C.R.J.; de Vivo, B.

    1993-01-01

    Detailed sampling of the Vesuvius lavas erupted in the period A.D. 1631-1944 provides a suite of samples for comprehensive chemical analyses and related studies. Major elements (Si, Ti, Al, Fetotal, Mn, Mg, Ca, Na, K and P), volatile species (Cl, F, S, H2O+, H2O- and CO2), and ferrous iron (Fe2+) were determined for one hundred and forty-nine lavas and five tephra from the A.D. 1631-1944 Vesuvius activity. The lavas represent a relatively homogeneous suite with respect to SiO2, TiO2, FeOtotal, MnO and P2O5, but show systematic variations among MgO, K2O, Na2O, Al2O3 and CaO. The average SiO2 content is 48.0 wt.% and the rocks are classified as tephriphonolites according to their content of alkalis. All of the lavas are silica-undersaturated and are nepheline, leucite, and olivine normative. There is no systematic variation in major-element composition with time, over the period A.D. 1631-1944. The inter-eruption and intra-eruption compositional differences are the same magnitude. The lavas are highly porphyritic with clinopyroxene and leucite as the major phases. Fractionation effects are not reflected in the silica content of the lavas. The variability of MgO, K2O, Na2O, and CaO can be modelled as a relative depletion or accumulation of clinopyroxene. ?? 1993.

  4. Catalytic activity and selectivity of mechanically alloyed nickel-zirconium and nickel-platinum-zirconium powders

    NASA Astrophysics Data System (ADS)

    Montes, Arvin Joseph

    2001-07-01

    Using a flow reactor, amorphous mechanically alloyed NiZr and NiPtZr powders milled in 1 x 10-6 Torr vacuum were studied as potential catalysts for the NO decomposition and Fischer-Tropsch reactions. A commercial Ni/SiO2-Al2O3 catalyst was tested under the same conditions and used as a standard for comparison. Material characterization of the catalysts in the as-received and after reaction conditions was achieved using B.E.T., CO chemisorption, TGA, XRD, SEM, and TEM. The TOF's of the mechanically alloyed Ni55Zr45 and Ni49PtZr 50 catalysts for the NO decomposition reaction at a reaction temperature of 673 K were two orders of magnitude greater than the commercial Ni/SiO 2-Al2O3 catalyst. The high activity of the mechanically alloyed catalysts for the NO decomposition reaction is believed to be due to an increase in the number of active sites, which occurred when the catalysts were exposed to reaction conditions. For the Fischer-Tropseh reaction, the most significant result was the selectivity of the mechanically alloyed NiZr and NiPtZr towards alkenes, compared to the commercial Ni/SiO2-Al 2O3 catalyst, which did not produce any alkenes. Fischer-Tropsch activity results for both the mechanically alloyed NiZr and NiPtZr catalysts showed the TOF to be an order of magnitude greater than the commercial Ni/SiO 2-Al2O3 catalyst. The high activity of the mechanically alloyed NiZr and NiPtZr catalysts was attributed to a strong metal support interaction between crystalline Ni-containing compounds and ZrOx, which formed during exposure to isothermal reaction conditions. The transformation of the mechanically alloyed catalysts into crystalline Ni/NiZr and ZrO x also affected the selectivity, resulting in a shift towards the production of primarily methane.

  5. Immobilization of silver nanoparticles synthesized using Curcuma longa tuber powder and extract on cotton cloth for bactericidal activity.

    PubMed

    Sathishkumar, Muthuswamy; Sneha, Krishnamurthy; Yun, Yeoung-Sang

    2010-10-01

    The present study reports the synthesis of silver (Ag) nanoparticles from silver precursor using plant biomaterials, Curcuma longa tuber powder and extract. Water-soluble organics present in the plant materials were mainly responsible for the reduction of silver ions to nano-sized silver particles. pH played a major role in size control of the particles. Silver nanoparticle synthesis was higher in tuber extract compared to powder, which was attributed to the large and easy availability of the reducing agents in the extract. Zeta potential studies showed that the surface charge of the formed nanoparticles was highly negative. The minimum bactericidal concentration (MBC) for Escherichia coli BL-21 strain was found to be 50 mg/L. Immobilization of silver nanoparticles on cotton cloth using sterile water showed better bactericidal activity when compared to polyvinylidene fluoride (PVDF) immobilized cloth, but on consecutive washing the activity reduced drastically in sterile water immobilized cloth. PMID:20541399

  6. Treatment of micropollutants in municipal wastewater: ozone or powdered activated carbon?

    PubMed

    Margot, Jonas; Kienle, Cornelia; Magnet, Anoÿs; Weil, Mirco; Rossi, Luca; de Alencastro, Luiz Felippe; Abegglen, Christian; Thonney, Denis; Chèvre, Nathalie; Schärer, Michael; Barry, D A

    2013-09-01

    Many organic micropollutants present in wastewater, such as pharmaceuticals and pesticides, are poorly removed in conventional wastewater treatment plants (WWTPs). To reduce the release of these substances into the aquatic environment, advanced wastewater treatments are necessary. In this context, two large-scale pilot advanced treatments were tested in parallel over more than one year at the municipal WWTP of Lausanne, Switzerland. The treatments were: i) oxidation by ozone followed by sand filtration (SF) and ii) powdered activated carbon (PAC) adsorption followed by either ultrafiltration (UF) or sand filtration. More than 70 potentially problematic substances (pharmaceuticals, pesticides, endocrine disruptors, drug metabolites and other common chemicals) were regularly measured at different stages of treatment. Additionally, several ecotoxicological tests such as the Yeast Estrogen Screen, a combined algae bioassay and a fish early life stage test were performed to evaluate effluent toxicity. Both treatments significantly improved the effluent quality. Micropollutants were removed on average over 80% compared with raw wastewater, with an average ozone dose of 5.7 mg O3 l(-1) or a PAC dose between 10 and 20 mg l(-1). Depending on the chemical properties of the substances (presence of electron-rich moieties, charge and hydrophobicity), either ozone or PAC performed better. Both advanced treatments led to a clear reduction in toxicity of the effluents, with PAC-UF performing slightly better overall. As both treatments had, on average, relatively similar efficiency, further criteria relevant to their implementation were considered, including local constraints (e.g., safety, sludge disposal, disinfection), operational feasibility and cost. For sensitive receiving waters (drinking water resources or recreational waters), the PAC-UF treatment, despite its current higher cost, was considered to be the most suitable option, enabling good removal of most micropollutants

  7. Treatment of micropollutants in municipal wastewater: ozone or powdered activated carbon?

    PubMed

    Margot, Jonas; Kienle, Cornelia; Magnet, Anoÿs; Weil, Mirco; Rossi, Luca; de Alencastro, Luiz Felippe; Abegglen, Christian; Thonney, Denis; Chèvre, Nathalie; Schärer, Michael; Barry, D A

    2013-09-01

    Many organic micropollutants present in wastewater, such as pharmaceuticals and pesticides, are poorly removed in conventional wastewater treatment plants (WWTPs). To reduce the release of these substances into the aquatic environment, advanced wastewater treatments are necessary. In this context, two large-scale pilot advanced treatments were tested in parallel over more than one year at the municipal WWTP of Lausanne, Switzerland. The treatments were: i) oxidation by ozone followed by sand filtration (SF) and ii) powdered activated carbon (PAC) adsorption followed by either ultrafiltration (UF) or sand filtration. More than 70 potentially problematic substances (pharmaceuticals, pesticides, endocrine disruptors, drug metabolites and other common chemicals) were regularly measured at different stages of treatment. Additionally, several ecotoxicological tests such as the Yeast Estrogen Screen, a combined algae bioassay and a fish early life stage test were performed to evaluate effluent toxicity. Both treatments significantly improved the effluent quality. Micropollutants were removed on average over 80% compared with raw wastewater, with an average ozone dose of 5.7 mg O3 l(-1) or a PAC dose between 10 and 20 mg l(-1). Depending on the chemical properties of the substances (presence of electron-rich moieties, charge and hydrophobicity), either ozone or PAC performed better. Both advanced treatments led to a clear reduction in toxicity of the effluents, with PAC-UF performing slightly better overall. As both treatments had, on average, relatively similar efficiency, further criteria relevant to their implementation were considered, including local constraints (e.g., safety, sludge disposal, disinfection), operational feasibility and cost. For sensitive receiving waters (drinking water resources or recreational waters), the PAC-UF treatment, despite its current higher cost, was considered to be the most suitable option, enabling good removal of most micropollutants

  8. Removal of micropollutants in municipal wastewater treatment plants by powder-activated carbon.

    PubMed

    Boehler, M; Zwickenpflug, B; Hollender, J; Ternes, T; Joss, A; Siegrist, H

    2012-01-01

    Micropollutants (MP) are only partly removed from municipal wastewater by nutrient removal plants and are seen increasingly as a threat to aquatic ecosystems and to the safety of drinking water resources. The addition of powder activated carbon (PAC) is a promising technology to complement municipal nutrient removal plants in order to achieve a significant reduction of MPs and ecotoxicity in receiving waters. This paper presents the salient outcomes of pilot- and full-scale applications of PAC addition in different flow schemes for micropollutant removal in municipal wastewater treatment plants (WWTPs). The sorption efficiency of PAC is reduced with increasing dissolved organic carbon (DOC). Adequate treatment of secondary effluent with 5-10 g DOC m(-3) requires 10-20 g PAC m(-3) of effluent. Counter-current use of PAC by recycling waste PAC from post-treatment in a contact tank with an additional clarifier to the biology tank improved the overall MP removal by 10 to 50% compared with effluent PAC application alone. A dosage of 15 g PAC m(-3) to a full-scale flocculation sand filtration system and recycling the backwash water to the biology tank showed similar MP elimination. Due to an adequate mixing regime and the addition of adapted flocculants, a good retention of the fine fraction of the PAC in the deep-bed filter were observed (1-3 g TSS m(-3); TSS: total suspended solids). With double use of PAC, only half of the PAC was required to reach MP removal efficiencies similar to the direct single dosage of PAC to the biology tank. Overall, the application of PAC in WWTPs seems to be an adequate and feasible technology for efficient MP elimination (>80%) from wastewater comparable with post ozonation. PMID:22949241

  9. Removal of micropollutants in municipal wastewater treatment plants by powder-activated carbon.

    PubMed

    Boehler, M; Zwickenpflug, B; Hollender, J; Ternes, T; Joss, A; Siegrist, H

    2012-01-01

    Micropollutants (MP) are only partly removed from municipal wastewater by nutrient removal plants and are seen increasingly as a threat to aquatic ecosystems and to the safety of drinking water resources. The addition of powder activated carbon (PAC) is a promising technology to complement municipal nutrient removal plants in order to achieve a significant reduction of MPs and ecotoxicity in receiving waters. This paper presents the salient outcomes of pilot- and full-scale applications of PAC addition in different flow schemes for micropollutant removal in municipal wastewater treatment plants (WWTPs). The sorption efficiency of PAC is reduced with increasing dissolved organic carbon (DOC). Adequate treatment of secondary effluent with 5-10 g DOC m(-3) requires 10-20 g PAC m(-3) of effluent. Counter-current use of PAC by recycling waste PAC from post-treatment in a contact tank with an additional clarifier to the biology tank improved the overall MP removal by 10 to 50% compared with effluent PAC application alone. A dosage of 15 g PAC m(-3) to a full-scale flocculation sand filtration system and recycling the backwash water to the biology tank showed similar MP elimination. Due to an adequate mixing regime and the addition of adapted flocculants, a good retention of the fine fraction of the PAC in the deep-bed filter were observed (1-3 g TSS m(-3); TSS: total suspended solids). With double use of PAC, only half of the PAC was required to reach MP removal efficiencies similar to the direct single dosage of PAC to the biology tank. Overall, the application of PAC in WWTPs seems to be an adequate and feasible technology for efficient MP elimination (>80%) from wastewater comparable with post ozonation.

  10. Performance evaluation of powdered activated carbon for removing 28 types of antibiotics from water.

    PubMed

    Zhang, Xinbo; Guo, Wenshan; Ngo, Huu Hao; Wen, Haitao; Li, Nan; Wu, Wei

    2016-05-01

    Currently, the occurrence and fate of antibiotics in the aquatic environment has become a very serious problem in that they can potentially and irreversibly damage the ecosystem and human health. For this reason, interest has increased in developing strategies to remove antibiotics from water. This study evaluated the performance of powdered activated carbon (PAC) in removing from water 6 representative groups of 28 antibiotics, namely Tetracyclines (TCs), Macrolides (MCs), Chloramphenicols (CPs), Penicillins (PNs), Sulfonamides (SAs) and Quinolones (QNs). Results indicate that PAC demonstrated superior adsorption capacity for all selected antibiotics. The removal efficiency was up to 99.9% in deionized water and 99.6% in surface water at the optimum conditions with PAC dosage of 20 mg/L and contact time of 120 min. According to the Freundlich model's adsorption isotherm, the values of n varied among these antibiotics and most were less than 1, suggesting that the adsorption of antibiotics onto PAC was nonlinear. Adsorption of antibiotics followed well the pseudo-second-order kinetic model (R(2) = 0.99). Analysis using the Weber-Morris model revealed that the intra-particle diffusion was not the only rate-controlling step. Overall, the findings in this study confirm that PAC is a feasible and viable option for removing antibiotics from water in terms of water quality improvement and urgent antibiotics pollution control. Further research is essential on the following subjects: (i) removing more types of antibiotics by PAC; (ii) the adsorption process; and (iii) the mechanism of the competitive adsorption existing between natural organic matters (NOMs) and antibiotics. PMID:26946168

  11. Evaluation of refractory organic removal in combined biological powdered activated carbon--microfiltration for advanced wastewater treatment.

    PubMed

    Seo, G T; Ohgaki, S

    2001-01-01

    Biological powdered activated carbon (BPAC) was incorporated with a microfiltration (MF, 0.2 micron pore size) system to remove the refractory organic matter contained in secondary sewage effluent. A synthetic secondary sewage effluent was used as influent in this study, containing both non-biodegradable organic substances (such as humic acid, lignin sulfonate, tannic acid and arabic gum powder) and biodegradable ones. These refractory organic materials were possibly degraded in contact with microorganisms for 20-27 days. Although humic acid and arabic gum were weakly adsorbed on the activated carbon, they could be effectively removed in the BPAC reactor. The TOC removal at a powdered activated carbon (PAC) concentration of 20 g/L was higher than at 0.5-2 g PAC/L (83% and 66-68%, respectively). The higher removal efficiency was due to the increased rejection at the membrane module in which most of the PAC was accumulated. More than 90% of non-biodegradable compounds removal (detected as E280, UV absorption at 280 nm) occurred in the BPAC reactor. The biological growth parameter b/Y, used in system design, was estimated to be 0.017 d-1. Relatively high permeate flux of 1.88 m/d could be obtained even at higher PAC concentration of 20 g/L.

  12. Assays of physical stability and antioxidant activity of a topical formulation added with different plant extracts.

    PubMed

    Di Mambro, Valéria M; Fonseca, Maria J V

    2005-02-23

    In the present investigation the changes on physical stability (pH, viscosity, flow index and tixotropy) of topical formulations were evaluated following inclusion of different plant extracts containing flavonoids. Also, the antioxidant effect of these plant extracts alone and after addition in the formulation was evaluated using chemiluminescence and the stable free radical 1,1-diphenyl-2-picrylhydrazyl (DPPH(.-)) assays, as well as the inhibition of lipid peroxidation. Formulation added with dl-alpha-tocopherol was used to compare the physical stability and antioxidant activity. Formulations with plant extracts showed pseudoplastic behavior with decreasing on viscosity and tixotropy. The Glycyrrhiza glabra (GG) and Ginkgo biloba (GB) extracts alone and the formulations containing these extracts showed great antioxidant and free radical scavenging activities while the other extracts studied (mixture of Glycyrrhiza glabra, Symphytum officinale L and Arctium majus root, Nelumbium speciosum and soybean) showed lower activity. The results suggest that GG and GB extracts may be used in topical formulations in order to protect skin against damage caused by free radical and reactive oxygen species. PMID:15708669

  13. Treatment of coke-oven wastewater with the powdered activated carbon-contact stabilization activated sludge process. Final report

    SciTech Connect

    Suidan, M.T.; Deady, M.A.; Gee, C.S.

    1983-11-01

    The objective of the study was to determine optimum parameters for the operation of an innovative process train used in the treatment of coke-over wastewater. The treatment process train consisted of a contact-stabilization activated sludge system with powdered activated carbon (PAC) addition, followed by activated sludge nitrification, followed by denitrification in an anoxic filter. The control and operating parameters evaluated during the study were: (a) the average mixed-liquor PAC concentration maintained in the contact-stabilization system, (b) the solids retention time practiced in the contact-stabilization system, and (c) the hydraulic detention time maintained in the contact aeration tank. Three identical treatement process trains were constructed and employed in this study. The coke-oven wastewater used for this investigation was fed to the treatment units at 30% strength. The first part of the study was devoted to determining the interactions between the mixed liquor PAC concentration and the solids retention time in the contact-stabilization tanks. Results showed that optimum overall system performance is attainable when the highest sludge age (30 day) and highest mixed liquor PAC concentration were practiced. During the second phase of the study, all three systems were operated at a 30 day solids retention time while different detention times of 1, 2/3 and 1/3 day were evaluated in the contact tank. PAC addition rates were maintained at the former levels and, consequently, reduced contact times entailed higher mixed liquor carbon concentrations. Once again, the system receiving the highest PAC addition rate of PAC exhibited the best overall performance. This system exhibited no deterioration in process performance as a result of decreased contact detention time. 72 references, 41 figures, 24 tables.

  14. Quantitative detection of powdered activated carbon in wastewater treatment plant effluent by thermogravimetric analysis (TGA).

    PubMed

    Krahnstöver, Therese; Plattner, Julia; Wintgens, Thomas

    2016-09-15

    For the elimination of potentially harmful micropollutants, powdered activated carbon (PAC) adsorption is applied in many wastewater treatment plants (WWTP). This holds the risk of PAC leakage into the WWTP effluent and desorption of contaminants into natural water bodies. In order to assess a potential PAC leakage, PAC concentrations below several mg/L have to be detected in the WWTP effluent. None of the methods that are used for water analysis today are able to differentiate between activated carbon and solid background matrix. Thus, a selective, quantitative and easily applicable method is still needed for the detection of PAC residues in wastewater. In the present study, a method was developed to quantitatively measure the PAC content in wastewater by using filtration and thermogravimetric analysis (TGA), which is a well-established technique for the distinction between different solid materials. For the sample filtration, quartz filters with a temperature stability up to 950 °C were used. This allowed for sensitive and well reproducible measurements, as the TGA was not affected by the presence of the filter. The sample's mass fractions were calculated by integrating the mass decrease rate obtained by TGA in specific, clearly identifiable peak areas. A two-step TGA heating method consisting of N2 and O2 atmospheres led to a good differentiation between PAC and biological background matrix, thanks to the reduction of peak overlapping. A linear correlation was found between a sample's PAC content and the corresponding peak areas under N2 and O2, the sample volume and the solid mass separated by filtration. Based on these findings, various wastewater samples from different WWTPs were then analyzed by TGA with regard to their PAC content. It was found that, compared to alternative techniques such as measurement of turbidity or total suspended solids, the newly developed TGA method allows for a quantitative and selective detection of PAC concentrations down to 0

  15. Removal of highly polar micropollutants from wastewater by powdered activated carbon.

    PubMed

    Kovalova, Lubomira; Knappe, Detlef R U; Lehnberg, Kai; Kazner, Christian; Hollender, Juliane

    2013-06-01

    Due to concerns about ecotoxicological effects of pharmaceuticals and other micropollutants released from wastewater treatment plants, activated carbon adsorption is one of the few processes to effectively reduce the concentrations of micropollutants in wastewater. Although aimed mainly at apolar compounds, polar compounds are also simultaneously removed to a certain extent, which has rarely been studied before. In this study, adsorption isotherm and batch kinetic data were collected with two powdered activated carbons (PACs) to assess the removal of the polar pharmaceuticals 5-fluorouracil (5-Fu) and cytarabine (CytR) from ultrapure water and wastewater treatment plant effluent. At pH 7.8, single-solute adsorption isotherm data for the weak acid 5-Fu and the weak base CytR showed that their adsorption capacities were about 1 order of magnitude lower than those of the less polar endocrine disrupting chemicals bisphenol A (BPA) and 17-α-ethinylestradiol (EE2). To remove 90 % of the adsorbate from a single-solute solution 14, 18, 70, and 87 mg L(-1) of HOK Super is required for EE2, BPA, CytR, and 5-Fu, respectively. Effects of solution pH, ionic strength, temperature, and effluent organic matter (EfOM) on 5-Fu and CytR adsorption were evaluated for one PAC. Among the studied factors, the presence of EfOM had the highest effect, due to a strong competition on 5-Fu and CytR adsorption. Adsorption isotherm and kinetic data and their modeling with a homogeneous surface diffusion model showed that removal percentage in the presence of EfOM was independent on the initial concentration of the ionizable compounds 5-Fu and CytR. These results are similar to neutral organic compounds in the presence of natural organic matter. Overall, results showed that PAC doses sufficient to remove >90 % of apolar adsorbates were able to remove no more than 50 % of the polar adsorbates 5-Fu and CytR and that the contact time is a critical parameter. PMID:23299971

  16. Removal of iodide from water by chlorination and subsequent adsorption on powdered activated carbon.

    PubMed

    Ikari, Mariya; Matsui, Yoshihiko; Suzuki, Yuta; Matsushita, Taku; Shirasaki, Nobutaka

    2015-01-01

    Chlorine oxidation followed by treatment with activated carbon was studied as a possible method for removing radioactive iodine from water. Chlorination time, chlorine dose, the presence of natural organic matter (NOM), the presence of bromide ion (Br⁻), and carbon particle size strongly affected iodine removal. Treatment with superfine powdered activated carbon (SPAC) after 10-min oxidation with chlorine (1 mg-Cl₂/L) removed 90% of the iodine in NOM-containing water (dissolved organic carbon concentration, 1.5 mg-C/L). Iodine removal in NOM-containing water increased with increasing chlorine dose up to 0.1 mg-Cl₂/L but decreased at chlorine doses of >1.0 mg-Cl₂/L. At a low chlorine dose, nonadsorbable iodide ion (I⁻) was oxidized to adsorbable hypoiodous acid (HOI). When the chlorine dose was increased, some of the HOI reacted with NOM to form adsorbable organic iodine (organic-I). Increasing the chlorine dose further did not enhance iodine removal, owing to the formation of nonadsorbable iodate ion (IO₃⁻). Co-existing Br⁻ depressed iodine removal, particularly in NOM-free water, because hypobromous acid (HOBr) formed and catalyzed the oxidation of HOI to IO₃⁻. However, the effect of Br⁻ was small in the NOM-containing water because organic-I formed instead of IO₃⁻. SPAC (median particle diameter, 0.62 μm) had a higher equilibrium adsorption capacity for organic-I than did conventional PAC (median diameter, 18.9 μm), but the capacities of PAC and SPAC for HOI were similar. The reason for the higher equilibrium adsorption capacity for organic-I was that organic-I was adsorbed principally on the exterior of the PAC particles and not inside the PAC particles, as indicated by direct visualization of the solid-phase iodine concentration profiles in PAC particles by field emission electron probe microanalysis. In contrast, HOI was adsorbed evenly throughout the entire PAC particle. PMID:25462731

  17. Quantitative detection of powdered activated carbon in wastewater treatment plant effluent by thermogravimetric analysis (TGA).

    PubMed

    Krahnstöver, Therese; Plattner, Julia; Wintgens, Thomas

    2016-09-15

    For the elimination of potentially harmful micropollutants, powdered activated carbon (PAC) adsorption is applied in many wastewater treatment plants (WWTP). This holds the risk of PAC leakage into the WWTP effluent and desorption of contaminants into natural water bodies. In order to assess a potential PAC leakage, PAC concentrations below several mg/L have to be detected in the WWTP effluent. None of the methods that are used for water analysis today are able to differentiate between activated carbon and solid background matrix. Thus, a selective, quantitative and easily applicable method is still needed for the detection of PAC residues in wastewater. In the present study, a method was developed to quantitatively measure the PAC content in wastewater by using filtration and thermogravimetric analysis (TGA), which is a well-established technique for the distinction between different solid materials. For the sample filtration, quartz filters with a temperature stability up to 950 °C were used. This allowed for sensitive and well reproducible measurements, as the TGA was not affected by the presence of the filter. The sample's mass fractions were calculated by integrating the mass decrease rate obtained by TGA in specific, clearly identifiable peak areas. A two-step TGA heating method consisting of N2 and O2 atmospheres led to a good differentiation between PAC and biological background matrix, thanks to the reduction of peak overlapping. A linear correlation was found between a sample's PAC content and the corresponding peak areas under N2 and O2, the sample volume and the solid mass separated by filtration. Based on these findings, various wastewater samples from different WWTPs were then analyzed by TGA with regard to their PAC content. It was found that, compared to alternative techniques such as measurement of turbidity or total suspended solids, the newly developed TGA method allows for a quantitative and selective detection of PAC concentrations down to 0

  18. Effect of the method of introduction of Y2O3 into NiAl-based powder alloys on their structure: II. Mechanical activation

    NASA Astrophysics Data System (ADS)

    Skachkov, O. A.; Povarova, K. B.; Drozdov, A. A.; Morozov, A. E.; Pozharov, S. V.

    2012-09-01

    Effect of mechanical activation of NiAl powders produced by calcium hydride reduction in an attritor and a ball mill on the specific surface, the oxygen concentration, the strain hardening, and the coherent domain size (CDS) of the powders is studied. It is found that the powder specific surface milled in the attritor for 10-15 h is larger by a factor of 1.7-1.8 and the oxygen concentration in a powder is lower by a factor of 1.35 as compared to the its milling in the ball mill for 150 h. The powders milled in the attritor for 15 h have the level of microstresses higher by a factor of ˜2.4 and the CDS smaller by a factor of 2 as compared to the powder treated in the ball mill for 150 h. When milling a powder in the attritor, the milling time decreases by a factor of 10 and the degree of powder refinement increases, which improves the technological characteristics of the powders. As a result of the combination (in one operation) of mechanical activation of an NiAl intermetallic matrix powder in the attritor and the introduction of dispersed particles of a refractory oxide Y2O3 powder, the produced composite alloy has a density close to the theoretical one and has no aggregates of dispersed oxide particles at grain boundary junctions. Submicro- and nanosized oxide particles are homogenously distributed in the intermetallic matrix volume, which is characterized by a homogeneous distribution of nickel and aluminum.

  19. Antifungal activity by vapor contact of essential oils added to amaranth, chitosan, or starch edible films.

    PubMed

    Avila-Sosa, Raúl; Palou, Enrique; Jiménez Munguía, María Teresa; Nevárez-Moorillón, Guadalupe Virginia; Navarro Cruz, Addí Rhode; López-Malo, Aurelio

    2012-02-01

    Antimicrobial agents can be incorporated into edible films to provide microbiological stability, since films can be used as carriers of a variety of additives to extend product shelf life and reduce the risk of microbial growth on food surfaces. Addition of antimicrobial agents to edible films offers advantages such as the use of small antimicrobial concentrations and low diffusion rates. The aim of this study was to evaluate inhibition by vapor contact of Aspergillus niger and Penicillium digitatum by selected concentrations of Mexican oregano (Lippia berlandieri Schauer), cinnamon (Cinnamomum verum) or lemongrass (Cymbopogon citratus) essential oils (EOs) added to amaranth, chitosan, or starch edible films. Essential oils were characterized by gas chromatography-mass spectrometry (GC/MS) analysis. Amaranth, chitosan and starch edible films were formulated with essential oil concentrations of 0.00, 0.25, 0.50, 0.75, 1.00, 2.00, or 4.00%. Antifungal activity was evaluated by determining the mold radial growth on agar media inoculated with A. niger and P. digitatum after exposure to vapors arising from essential oils added to amaranth, chitosan or starch films using the inverted lid technique. The modified Gompertz model adequately described mold growth curves (mean coefficient of determination 0.991 ± 0.05). Chitosan films exhibited better antifungal effectiveness (inhibition of A. niger with 0.25% of Mexican oregano and cinnamon EO; inhibition of P. digitatum with 0.50% EOs) than amaranth films (2.00 and 4.00% of cinnamon and Mexican oregano EO were needed to inhibit the studied molds, respectively). For chitosan and amaranth films a significant increase (p<0.05) of lag phase was observed among film concentrations while a significant decrease (p<0.05) of maximum specific growth was determined. Chitosan edible films incorporating Mexican oregano or cinnamon essential oil could improve the quality of foods by the action of the volatile compounds on surface growth

  20. Antifungal activity by vapor contact of essential oils added to amaranth, chitosan, or starch edible films.

    PubMed

    Avila-Sosa, Raúl; Palou, Enrique; Jiménez Munguía, María Teresa; Nevárez-Moorillón, Guadalupe Virginia; Navarro Cruz, Addí Rhode; López-Malo, Aurelio

    2012-02-01

    Antimicrobial agents can be incorporated into edible films to provide microbiological stability, since films can be used as carriers of a variety of additives to extend product shelf life and reduce the risk of microbial growth on food surfaces. Addition of antimicrobial agents to edible films offers advantages such as the use of small antimicrobial concentrations and low diffusion rates. The aim of this study was to evaluate inhibition by vapor contact of Aspergillus niger and Penicillium digitatum by selected concentrations of Mexican oregano (Lippia berlandieri Schauer), cinnamon (Cinnamomum verum) or lemongrass (Cymbopogon citratus) essential oils (EOs) added to amaranth, chitosan, or starch edible films. Essential oils were characterized by gas chromatography-mass spectrometry (GC/MS) analysis. Amaranth, chitosan and starch edible films were formulated with essential oil concentrations of 0.00, 0.25, 0.50, 0.75, 1.00, 2.00, or 4.00%. Antifungal activity was evaluated by determining the mold radial growth on agar media inoculated with A. niger and P. digitatum after exposure to vapors arising from essential oils added to amaranth, chitosan or starch films using the inverted lid technique. The modified Gompertz model adequately described mold growth curves (mean coefficient of determination 0.991 ± 0.05). Chitosan films exhibited better antifungal effectiveness (inhibition of A. niger with 0.25% of Mexican oregano and cinnamon EO; inhibition of P. digitatum with 0.50% EOs) than amaranth films (2.00 and 4.00% of cinnamon and Mexican oregano EO were needed to inhibit the studied molds, respectively). For chitosan and amaranth films a significant increase (p<0.05) of lag phase was observed among film concentrations while a significant decrease (p<0.05) of maximum specific growth was determined. Chitosan edible films incorporating Mexican oregano or cinnamon essential oil could improve the quality of foods by the action of the volatile compounds on surface growth

  1. Effect of Time and storage temperature on anthocyanin decay and antioxidant activity in wild blueberry ( Vaccinium angustifolium ) powder.

    PubMed

    Fracassetti, Daniela; Del Bo', Cristian; Simonetti, Paolo; Gardana, Claudio; Klimis-Zacas, Dorothy; Ciappellano, Salvatore

    2013-03-27

    This study evaluated the effects of storage on total and single anthocyanin (ACN) content, and total antioxidant activity (TAA) of freeze-dried wild blueberry (WB) powder maintained at 25, 42, 60, and 80 °C for 49 days. Storage reduced single and total ACN content at all of the temperatures; it was slower at 25 °C (-3% after 2 weeks), whereas it was faster at 60 °C (-60%) and at 80 °C (-85%) after 3 days. The values of half-life time (t1/2) were found to be 139, 39, and 12 days at 25, 42, and 60 °C, respectively, utilizing the Arrhenius equation. No significant effects were detected on TAA by temperature increase. In conclusion, this study provides important information on the stability of WB powder at 25 °C; this is interesting scientific research for the food industry. PMID:23489164

  2. Preservation of cocoa antioxidant activity, total polyphenols, flavan-3-ols, and procyanidin content in foods prepared with cocoa powder.

    PubMed

    Stahl, L; Miller, K B; Apgar, J; Sweigart, D S; Stuart, D A; McHale, N; Ou, B; Kondo, M; Hurst, W J

    2009-08-01

    Little is known about the effects of common cooking processes on cocoa flavanols. Antioxidant activity, total polyphenols (TP), flavanol monomers, and procyanidin oligomers were determined in chocolate frosting, a hot cocoa drink, chocolate cookies, and chocolate cake made with natural cocoa powder. Recoveries of antioxidant activity, TP, flavanol monomers, and procyanidins ranged from 86% to over 100% in the chocolate frosting, hot cocoa drink, and chocolate cookies. Losses were greatest in the chocolate cake with recoveries ranging from 5% for epicatechin to 54% for antioxidant activity. The causes of losses in baked chocolate cakes were investigated by exchanging baking soda with baking powder or combinations of the 2 leavening agents. Use of baking soda as a leavening agent was associated with increased pH and darkening color of cakes. Losses of antioxidant activity, TP, flavanol monomers, and procyanidins were associated with an increased extractable pH of the baked cakes. Chocolate cakes made with baking powder for leavening resulted in an average extractable pH of 6.2 with essentially complete retention of antioxidant activity and flavanol content, but with reduced cake heights and lighter cake color. Commercially available chocolate cake mixes had final pHs above 8.3 and contained no detectable monomeric flavanols after baking. These results suggest that baking soda causes an increase in pH and subsequent destruction of flavanol compounds and antioxidant activity. Use of an appropriate leavening agent to moderate the final cake pH to approximately 7.25 or less results in both good leavening and preservation of cocoa flavanols and procyanidins. PMID:19723182

  3. Preservation of cocoa antioxidant activity, total polyphenols, flavan-3-ols, and procyanidin content in foods prepared with cocoa powder.

    PubMed

    Stahl, L; Miller, K B; Apgar, J; Sweigart, D S; Stuart, D A; McHale, N; Ou, B; Kondo, M; Hurst, W J

    2009-08-01

    Little is known about the effects of common cooking processes on cocoa flavanols. Antioxidant activity, total polyphenols (TP), flavanol monomers, and procyanidin oligomers were determined in chocolate frosting, a hot cocoa drink, chocolate cookies, and chocolate cake made with natural cocoa powder. Recoveries of antioxidant activity, TP, flavanol monomers, and procyanidins ranged from 86% to over 100% in the chocolate frosting, hot cocoa drink, and chocolate cookies. Losses were greatest in the chocolate cake with recoveries ranging from 5% for epicatechin to 54% for antioxidant activity. The causes of losses in baked chocolate cakes were investigated by exchanging baking soda with baking powder or combinations of the 2 leavening agents. Use of baking soda as a leavening agent was associated with increased pH and darkening color of cakes. Losses of antioxidant activity, TP, flavanol monomers, and procyanidins were associated with an increased extractable pH of the baked cakes. Chocolate cakes made with baking powder for leavening resulted in an average extractable pH of 6.2 with essentially complete retention of antioxidant activity and flavanol content, but with reduced cake heights and lighter cake color. Commercially available chocolate cake mixes had final pHs above 8.3 and contained no detectable monomeric flavanols after baking. These results suggest that baking soda causes an increase in pH and subsequent destruction of flavanol compounds and antioxidant activity. Use of an appropriate leavening agent to moderate the final cake pH to approximately 7.25 or less results in both good leavening and preservation of cocoa flavanols and procyanidins.

  4. Solar activity and climate change during the 1750 A.D. solar minimum

    NASA Astrophysics Data System (ADS)

    Bard, Edouard; Baroni, Mélanie; Aster Team

    2015-04-01

    The number of sunspots and other characteristics have been widely used to reconstruct the solar activity beyond the last three decades of accurate satellite measurements. It has also been possible to reconstruct the long-term solar behavior by measuring the abundance on Earth of cosmogenic nuclides such as carbon 14 and beryllium 10. These isotopes are formed by the interaction of galactic cosmic rays with atmospheric molecules. Accelerator mass spectrometry is used to measure the abundance of these isotopes in natural archives such as polar ice (for 10Be), tree rings and corals (for 14C). Over the last millennium, the solar activity has been dominated by alternating active and quiet periods, such as the Maunder Minimum, which occurred between 1645 and 1715 A.D. The climate forcing of this solar variability is the subject of intense research, both because the exact scaling in terms of irradiance is still a matter of debate and because other solar variations may have played a role in amplifying the climatic response. Indeed, the past few decades of accurate solar measurements do not include conditions equivalent to an extended solar minimum. A further difficulty of the analysis lies in the presence of other climate forcings during the last millennium, which are superimposed on the solar variations. Finally, the inherent precision of paleotemperature proxies are close to the signal amplitude retrieved from various paleoclimate archives covering the last millennium. Recent model-data comparisons for the last millennium have led to the conclusion that the solar forcing during this period was minor in comparison to volcanic eruptions and greenhouse gas concentrations (e.g. Schurer et al. 2013 J. Clim., 2014 Nat. Geo.). In order to separate the different forcings, it is useful to focus on a temperature change in phase with a well-documented solar minimum so as to maximize the response to this astronomical forcing. This is the approach followed by Wagner et al. (2005 Clim

  5. Cinnamon zeylanicum bark extract and powder mediated green synthesis of nano-crystalline silver particles and its bactericidal activity.

    PubMed

    Sathishkumar, M; Sneha, K; Won, S W; Cho, C-W; Kim, S; Yun, Y-S

    2009-10-15

    The exploitation of various plant materials for the biosynthesis of nanoparticles is considered a green technology as it does not involve any harmful chemicals. The present study reports the synthesis of silver (Ag) nanoparticles from silver precursor using the bark extract and powder of novel Cinnamon zeylanicum. Water-soluble organics present in the plant materials were mainly responsible for the reduction of silver ions to nano-sized Ag particles. TEM and XRD results confirmed the presence of nano-crystalline Ag particles. The pH played a major role in size control of the particles. Bark extract produced more Ag nanoparticles than the powder did, which was attributed to the large availability of the reducing agents in the extract. Zeta potential studies showed that the surface charge of the formed nanoparticles was highly negative. The EC(50) value of the synthesized nanoparticles against Escherichia coli BL-21 strain was 11+/-1.72 mg/L. Thus C. zeylanicum bark extract and powder are a good bio-resource/biomaterial for the synthesis of Ag nanoparticles with antimicrobial activity.

  6. SERS-active Au/SiO2 clouds in powder for rapid ex vivo breast adenocarcinoma diagnosis.

    PubMed

    Cepeda-Pérez, Elisa; López-Luke, Tzarara; Salas, Pedro; Plascencia-Villa, Germán; Ponce, Arturo; Vivero-Escoto, Juan; José-Yacamán, Miguel; de la Rosa, Elder

    2016-06-01

    In the present work, we report a dry-based application technique of Au/SiO2 clouds in powder for rapid ex vivo adenocarcinoma diagnosis through surface-enhanced Raman scattering (SERS); using low laser power and an integration time of one second. Several characteristic Raman peaks frequently used for the diagnosis of breast adenocarcinoma in the range of the amide III are successfully enhanced by breading the tissue with Au/SiO2 powder. The SERS activity of these Au/SiO2 powders is attributed to their rapid rehydration upon contact with the wet tissues, which promotes the formation of gold nanoparticle aggregates. The propensity of the Au/SiO2 cloud structures to adsorb biomolecules in the vicinity of the gold nanoparticle clusters promotes the necessary conditions for SERS detection. In addition, electron microscopy, together with elemental analysis, have been used to confirm the structure of the new Au/SiO2 cloud material and to investigate its distribution in breast tissues.

  7. SERS-active Au/SiO2 clouds in powder for rapid ex vivo breast adenocarcinoma diagnosis

    PubMed Central

    Cepeda-Pérez, Elisa; López-Luke, Tzarara; Salas, Pedro; Plascencia-Villa, Germán; Ponce, Arturo; Vivero-Escoto, Juan; José-Yacamán, Miguel; de la Rosa, Elder

    2016-01-01

    In the present work, we report a dry-based application technique of Au/SiO2 clouds in powder for rapid ex vivo adenocarcinoma diagnosis through surface-enhanced Raman scattering (SERS); using low laser power and an integration time of one second. Several characteristic Raman peaks frequently used for the diagnosis of breast adenocarcinoma in the range of the amide III are successfully enhanced by breading the tissue with Au/SiO2 powder. The SERS activity of these Au/SiO2 powders is attributed to their rapid rehydration upon contact with the wet tissues, which promotes the formation of gold nanoparticle aggregates. The propensity of the Au/SiO2 cloud structures to adsorb biomolecules in the vicinity of the gold nanoparticle clusters promotes the necessary conditions for SERS detection. In addition, electron microscopy, together with elemental analysis, have been used to confirm the structure of the new Au/SiO2 cloud material and to investigate its distribution in breast tissues. PMID:27375955

  8. SERS-active Au/SiO2 clouds in powder for rapid ex vivo breast adenocarcinoma diagnosis.

    PubMed

    Cepeda-Pérez, Elisa; López-Luke, Tzarara; Salas, Pedro; Plascencia-Villa, Germán; Ponce, Arturo; Vivero-Escoto, Juan; José-Yacamán, Miguel; de la Rosa, Elder

    2016-06-01

    In the present work, we report a dry-based application technique of Au/SiO2 clouds in powder for rapid ex vivo adenocarcinoma diagnosis through surface-enhanced Raman scattering (SERS); using low laser power and an integration time of one second. Several characteristic Raman peaks frequently used for the diagnosis of breast adenocarcinoma in the range of the amide III are successfully enhanced by breading the tissue with Au/SiO2 powder. The SERS activity of these Au/SiO2 powders is attributed to their rapid rehydration upon contact with the wet tissues, which promotes the formation of gold nanoparticle aggregates. The propensity of the Au/SiO2 cloud structures to adsorb biomolecules in the vicinity of the gold nanoparticle clusters promotes the necessary conditions for SERS detection. In addition, electron microscopy, together with elemental analysis, have been used to confirm the structure of the new Au/SiO2 cloud material and to investigate its distribution in breast tissues. PMID:27375955

  9. Biological Activities of Tetrodotoxin-Producing Enterococcus faecium AD1 Isolated from Puffer Fishes

    PubMed Central

    Nguyen, Tu Hoang Khue; Nguyen, Huu Ngoc; Nghe, Dat Van; Nguyen, Kim Hoang

    2015-01-01

    Puffer fishes were collected from the central sea in Vietnam from spring to summer season. The eggs were incubated in MRS broth that was used to test the toxicity in mice and isolate the lactic acid bacteria community that could produce tetrodotoxin (TTX). Thin layer chromatography (TLC) and high performance lipid chromatography (HPLC) were used to detect and quantify TTX. As a result, Enterococcus faecium AD1 which was identified by biochemical test and 16S rRNA analysis could produce TTX 0.3 mg/mL when cultured in MRS broth. The bacterium was optimized for TTX production and gave 0.18 mg/mL, 0.07 mg/mL, and 0.15 mg/mL in media prepared from the meat-washing water of freshwater fishes (Pangasius bocourti, Oreochromis sp.) and sea fish (Auxis thazard), respectively, that are also hopeful to answer some poisoning cases related to eating fishes. Enterococcus faecium also showed the wide antimicrobial activities on yeast, Gram-negative and -positive bacteria. Extracted exopolysaccharide (EPS) that reacted with 2,2-diphenyl-1-picrylhydrazyl to give IC50 at 5 mg/mL equaled 11 mg/mL ascorbic acid which could show effects on Hela-6 and Hep G2 using sulforhodamine B test. Enterococcus faecium can be claimed as a promising source in tetrodotoxin and biological compounds. PMID:26380310

  10. Biological Activities of Tetrodotoxin-Producing Enterococcus faecium AD1 Isolated from Puffer Fishes.

    PubMed

    Nguyen, Tu Hoang Khue; Nguyen, Huu Ngoc; Nghe, Dat Van; Nguyen, Kim Hoang

    2015-01-01

    Puffer fishes were collected from the central sea in Vietnam from spring to summer season. The eggs were incubated in MRS broth that was used to test the toxicity in mice and isolate the lactic acid bacteria community that could produce tetrodotoxin (TTX). Thin layer chromatography (TLC) and high performance lipid chromatography (HPLC) were used to detect and quantify TTX. As a result, Enterococcus faecium AD1 which was identified by biochemical test and 16S rRNA analysis could produce TTX 0.3 mg/mL when cultured in MRS broth. The bacterium was optimized for TTX production and gave 0.18 mg/mL, 0.07 mg/mL, and 0.15 mg/mL in media prepared from the meat-washing water of freshwater fishes (Pangasius bocourti, Oreochromis sp.) and sea fish (Auxis thazard), respectively, that are also hopeful to answer some poisoning cases related to eating fishes. Enterococcus faecium also showed the wide antimicrobial activities on yeast, Gram-negative and -positive bacteria. Extracted exopolysaccharide (EPS) that reacted with 2,2-diphenyl-1-picrylhydrazyl to give IC50 at 5 mg/mL equaled 11 mg/mL ascorbic acid which could show effects on Hela-6 and Hep G2 using sulforhodamine B test. Enterococcus faecium can be claimed as a promising source in tetrodotoxin and biological compounds. PMID:26380310

  11. JunB potentiates function of BRCA1 activation domain 1 (AD1) through a coiled-coil-mediated interaction

    PubMed Central

    Hu, Yan-Fen; Li, Rong

    2002-01-01

    BRCA1 is involved in the regulation of multiple nuclear events including transcription. AD1, one of the two trans-activation domains in BRCA1, stimulates transcription in a cell context-dependent manner. Here, it is shown that BRCA1 interacts with Jun proteins via a coiled-coil motif in AD1 and the basic leucine zipper (bZIP) region of the Jun proteins. The Jun-interacting domain in BRCA1 is critical for AD1-mediated transcriptional activation. In particular, the strength of AD1 in transcriptional activation is limited by the JunB level and ectopic expression of JunB potentiates the transcriptional activity of AD1. Furthermore, JunB mRNA expression is down-regulated in many ovarian tumor tissues examined. Thus, the coiled-coil-mediated cooperation between BRCA1 and JunB may facilitate the function of these proteins in tissue-specific transcriptional regulation and tumor suppression. PMID:12080089

  12. Removal of phenols and other pollutants from different landfill leachates using powdered activated carbon supplemented SBR technology.

    PubMed

    Aziz, Shuokr Qarani; Aziz, Hamidi Abdul; Yusoff, Mohd Suffian; Mohajeri, Soraya

    2012-10-01

    In this research, two types of sequencing batch reactors (SBRs) with 8 h of cycle times, namely non-powdered activated carbon (NPAC-SBR) and powdered activated carbon (PAC-SBR), were used for the treatment of raw leachates at Kulim and Pulau Burung landfill sites. To test the performance of SBRs, phenols, total iron, zinc, ammonia, nitrite, nitrate, color, suspended solids, chemical oxygen demand, biochemical oxygen demand, and total dissolved salts removal efficiencies and sludge volume index (SVI) were studied at both sites. The rates of phenols removal, for instance in NPAC-SBRs and PAC-SBRs at Kulim, were 25% and 55%, respectively, whereas those at Pulau Buring were 94.81% and 97.75%, respectively. PAC as adsorbent in PAC-SBRs enhanced the removal efficiencies of the aforementioned pollutants from leachates at both sites. In addition, PAC as adsorbent decreased the SVI values at Kulim (59.7 mL/g) and Pulau Burung (91.4 mL/g) leachates and improved the nitrification and denitrification processes. PMID:22068314

  13. Landfill leachate treatment using powdered activated carbon augmented sequencing batch reactor (SBR) process: optimization by response surface methodology.

    PubMed

    Aziz, Shuokr Qarani; Aziz, Hamidi Abdul; Yusoff, Mohd Suffian; Bashir, Mohammed J K

    2011-05-15

    In this study, landfill leachate was treated by using the sequencing batch reactor (SBR) process. Two types of the SBR, namely non-powdered activated carbon and powdered activated carbon (PAC-SBR) were used. The influence of aeration rate and contact time on SBR and PAC-SBR performances was investigated. Removal efficiencies of chemical oxygen demand (COD), colour, ammoniacal nitrogen (NH(3)-N), total dissolved salts (TDS), and sludge volume index (SVI) were monitored throughout the experiments. Response surface methodology (RSM) was applied for experimental design, analysis and optimization. Based on the results, the PAC-SBR displayed superior performance in term of removal efficiencies when compared to SBR. At the optimum conditions of aeration rate of 1L/min and contact time of 5.5h the PAC-SBR achieved 64.1%, 71.2%, 81.4%, and 1.33% removal of COD, colour, NH(3)-N, and TDS, respectively. The SVI value of PAC-SBR was 122.2 mL/g at optimum conditions. PMID:21420786

  14. Rheological, physical and sensorial evaluation of cookies supplemented with dairy powders.

    PubMed

    Sert, Durmuş; Demir, M Kürşat; Ertaş, Nilgün

    2016-04-01

    The effect of dairy powders (skim milk powder, butter milk powder, sodium caseinate, yoghurt powder, milk powder and colostrum powder) on cookie quality was studied. Cookies were tested for aw, calorimetric energy, diameter, thickness, spread ratio, breaking strength, colour, dough consistency and sensory evaluation. The lowest aw values were obtained for cookies containing colostrum powder; also the highest calorimetric energy values were obtained from the colostrum powder-added cookies. Diameter values of cookies with the addition of skim milk powder, butter milk powder, yoghurt powder and milk powder were higher than that of sodium caseinate and colostrum powder. The lowest spread ratio was measured in the cookie samples with added skim milk powder. The addition of yoghurt powder gave the highest breaking strength of cookies. Cookies with sodium caseinate addition exhibited the highest lightness (L*) values than the other cookies with different dairy powders. Cookies prepared with butter milk powder received the highest scores for colour, appearance, texture, crispness and overall acceptability.

  15. In vitro effect of air-abrasion operating parameters on dynamic cutting characteristics of alumina and bio-active glass powders.

    PubMed

    Milly, H; Austin, R S; Thompson, I; Banerjee, A

    2014-01-01

    Minimally invasive dentistry advocates the maintenance of all repairable tooth structures during operative caries management in combination with remineralization strategies. This study evaluated the effect of air-abrasion operating parameters on its cutting efficiency/pattern using bio-active glass (BAG) powder and alumina powder as a control in order to develop its use as a minimally invasive operative technique. The cutting efficiency/pattern assessment on an enamel analogue, Macor, was preceded by studying the powder flow rate (PFR) of two different commercial intraoral air-abrasion units with differing powder-air admix systems. The parameters tested included air pressure, powder flow rate, nozzle-substrate distance, nozzle angle, shrouding the air stream with a curtain of water, and the chemistry of abrasive powder. The abraded troughs were scanned and analyzed using confocal white light profilometry and MountainsMap surface analysis software. Data were analyzed statistically using one-way and repeated-measures analysis of variance tests (p=0.05). The air-abrasion unit using a vibration mechanism to admix the abrasive powder with the air stream exhibited a constant PFR regardless of the set air pressure. Significant differences in cutting efficiency were observed according to the tested parameters (p<0.05). Alumina powder removed significantly more material than did BAG powder. Using low air pressure and suitable consideration of the effect of air-abrasion parameters on cutting efficiency/patterns can improve the ultraconservative cutting characteristics of BAG air-abrasion, thereby allowing an introduction of this technology for the controlled cleaning/removal of enamel, where it is indicated clinically.

  16. [Recent progress of dry powder inhalation of proteins and peptides].

    PubMed

    Zhou, Jie-yu; Zhang, Lan; Mao, Shi-rui

    2015-07-01

    To provide theoretical and practical basis for the successful formulation design of physically-mixed inhalation dry powder of proteins and peptides, related references were collected, analyzed and summarized. In this review drug micronization technology and commonly used carriers for inhalation dry powder preparation were introduced. For proteins and peptides, supercritical fluid technology and spray-drying are more suitable because of their capabilities of keeping drug activity. Being approved by U. S. Food and Drug Administration, lactose has been extensively used as carriers in many inhalation products. Formulation and process factors influencing drug deposition in the lung, including carrier properties, drug-carrier ratio, blending order, mixing methods, mixing time and the interaction between drug and carrier, were elucidated. The size, shape and surface properties of carries all influence the interaction between drug and carrier. Besides, influence of micromeritic properties of the dry powder, such as particle size, shape, density, flowability, charge, dispersibility and hygroscopicity, on drug deposition in the lung was elaborated. Among these particle size plays the most crucial role in particle deposition in the lung. Moreover, based on the mechanisms of powder dispersity, some strategies to improve drug lung deposition were put forward, such as adding carrier fines, adding adhesive-controlling materials and reprocessing micronized drug. In order to design physically-mixed inhalation dry powder for proteins and peptides with high lung deposition, it is essential to study drug-carriers interactions systematically and illustrate the potential influence of formulation, process parameters and micromeritic properties of the powder. PMID:26552141

  17. Quantitation of active pharmaceutical ingredients and excipients in powder blends using designed multivariate calibration models by near-infrared spectroscopy.

    PubMed

    Li, Weiyong; Worosila, Gregory D

    2005-05-13

    This research note demonstrates the simultaneous quantitation of a pharmaceutical active ingredient and three excipients in a simulated powder blend containing acetaminophen, Prosolv and Crospovidone. An experimental design approach was used in generating a 5-level (%, w/w) calibration sample set that included 125 samples. The samples were prepared by weighing suitable amount of powders into separate 20-mL scintillation vials and were mixed manually. Partial least squares (PLS) regression was used in calibration model development. The models generated accurate results for quantitation of Crospovidone (at 5%, w/w) and magnesium stearate (at 0.5%, w/w). Further testing of the models demonstrated that the 2-level models were as effective as the 5-level ones, which reduced the calibration sample number to 50. The models had a small bias for quantitation of acetaminophen (at 30%, w/w) and Prosolv (at 64.5%, w/w) in the blend. The implication of the bias is discussed.

  18. Mechanism of enhanced nitrate reduction via micro-electrolysis at the powdered zero-valent iron/activated carbon interface.

    PubMed

    Luo, Jinghuan; Song, Guangyu; Liu, Jianyong; Qian, Guangren; Xu, Zhi Ping

    2014-12-01

    Nitrate reduction by zero-valent iron (Fe(0)) powder always works well only at controlled pH lower than 4 due to the formation of iron (hydr)oxides on its surface. Fe(0) powder combined with activated carbon (AC), i.e., Fe(0)/AC micro-electrolysis system, was first introduced to enhance nitrate reduction in aqueous solution. Comparative study was carried out to investigate nitrate reduction by Fe(0)/AC system and Fe(0) under near-neutral conditions, showing that the Fe(0)/AC system successfully reduced nitrate even at initial pH 6 with the reduction efficiency of up to 73%, whereas for Fe(0) only ∼10%. The effect of Fe(0) to AC mass ratio on nitrate reduction efficiency was examined. Easier nitrate reduction was achieved with more contact between Fe(0) and AC as the result of decreasing Fe(0) to AC mass ratio. Ferrous ion and oxidation-reduction potential were measured to understand the mechanism of enhanced nitrate reduction by Fe(0)/AC micro-electrolysis. The results suggest that a relative potential difference drives much more electrons from Fe(0) to AC, thus generating adsorbed atomic hydrogen which makes it possible for nitrate to be reduced at near-neural pH. Fe(0)/AC micro-electrolysis thus presents a great potential for practical application in nitrate wastewater treatment without excessive pH adjustment. PMID:25217726

  19. [TV, overweight and nutritional surveillance. Ads content, food intake and physical activity].

    PubMed

    Spagnoli, T D; Bioletti, L; Bo, C; Formigatti, M

    2003-01-01

    The relationship between television viewing and obesity in children and adults was examined in a large number of cross-sectional epidemiological studies. Some randomised, controlled trials confirmed the evidence that television viewing is a cause of increased body fatness. It seems of utility in nutritional surveillance to esteem time spent by children and adults in television watching and to evaluate ads contents and food preferences suggested by them. This editorial shows a two-years long analysis of food commercials broadcasted by the main Italian TV networks; food ads targeted on children, housewives and sport fans were evaluated; the relationship between television viewing, commercials and food intake or global lifestyle was investigated in a Piedmont's population (from Northern Italy). School projects aimed to reduce television viewing represent a promising strategy for preventing childhood obesity. PMID:14969315

  20. Compaction of Titanium Powders

    SciTech Connect

    Stephen J. Gerdemann; Paul D. Jablonski

    2010-11-01

    Accurate modeling of powder densification has been an area of active research for more than 60 years. The earliest efforts were focused on linearization of the data because computers were not readily available to assist with curve-fitting methods. In this work, eight different titanium powders (three different sizes of sponge fines <150 μm, <75 μm, and < 45 μm; two different sizes of a hydride-dehydride [HDH] <75 μm and < 45 μm; an atomized powder; a commercially pure [CP] Ti powder from International Titanium Powder [ITP]; and a Ti 6 4 alloy powder) were cold pressed in a single-acting die instrumented to collect stress and deformation data during compaction. From these data, the density of each compact was calculated and then plotted as a function of pressure. The results show that densification of all the powders, regardless of particle size, shape, or chemistry, can be modeled accurately as the sum of an initial density plus the sum of a rearrangement term and a work-hardening term. These last two terms are found to be a function of applied pressure and take the form of an exponential rise.

  1. Compaction of Titanium Powders

    NASA Astrophysics Data System (ADS)

    Gerdemann, Stephen J.; Jablonski, Paul D.

    2011-05-01

    Accurate modeling of powder densification has been an area of active research for more than 60 years. The earliest efforts were focused on linearization of the data because computers were not readily available to assist with curve-fitting methods. In this work, eight different titanium powders (three different sizes of sponge fines <150 μm, <75 μm, and < 45 μm; two different sizes of a hydride-dehydride [HDH] <75 μm and < 45 μm; an atomized powder; a commercially pure [CP] Ti powder from International Titanium Powder [ITP]; and a Ti 6 4 alloy powder) were cold pressed in a single-acting die instrumented to collect stress and deformation data during compaction. From these data, the density of each compact was calculated and then plotted as a function of pressure. The results show that densification of all the powders, regardless of particle size, shape, or chemistry, can be modeled accurately as the sum of an initial density plus the sum of a rearrangement term and a work-hardening term. These last two terms are found to be a function of applied pressure and take the form of an exponential rise.

  2. Managing daily intensive care activities: An observational study concerning ad hoc decision making of charge nurses and intensivists

    PubMed Central

    2011-01-01

    Introduction Management of daily activities in ICUs is challenging. ICU shift leaders, charge nurses and intensivists have to make several immediate ad hoc decisions to enable the fluent flow of ICU activities. Even though the management of ICU activities is quite well delineated by international consensus guidelines, we know only a little about the content of the real clinical decision making of ICU shift leaders. Methods We conducted an observational study with the think-aloud technique to describe the ad hoc decision making of ICU shift leaders. The study was performed in two university-affiliated hospital ICUs. Twelve charge nurses and eight intensivists were recruited. Observations were recorded and transcribed for qualitative content analysis using the protocol analysis method. The software program NVivo 7 was used to manage the data. The interrater agreement was assessed with percentages and by Cohen's κ. Results We identified 463 ad hoc decisions made by the charge nurses and 444 made by the intensivists. During our data collection time, this breaks down to over 230 immediately made decisions per day (24 hours). We divided the ad hoc decision making of ICU shift leaders into two types: process-focused and situation-focused. Process-focused decision making included more permanent information, such as human resources, know-how and material resources, whereas situation-focused decision making included decisions about single events, such as patient admission. We named eight different categories for ICU ad hoc decision making: (1) adverse events, (2) diagnostics, (3) human resources and know-how, (4) material resources, (5) patient admission, (6) patient discharge, (7) patient information and vital signs and (8) special treatments. Conclusions ICU shift leaders make a great number of complex ad hoc decisions throughout the day. Often this decision making involves both intensivists and charge nurses. It forms a bundle that requires versatile, immediate

  3. Temperature resistance of Salmonella in low-water activity whey protein powder as influenced by salt content.

    PubMed

    Santillana Farakos, S M; Hicks, J W; Frank, J F

    2014-04-01

    Salmonella can survive in low-water activity (a(w)) foods for long periods of time. Water activity and the presence of solutes may affect its survival during heating. Low-a(w) products that contain sodium levels above 0.1 % (wt/wt) and that have been involved in major Salmonella outbreaks include peanut products and salty snacks. Reduced a(w) protects against thermal inactivation. There is conflicting information regarding the role of salt. The aim of this study was to determine whether NaCl influences the survival of Salmonella in low-a(w) whey protein powder independent of a(w) at 70 and 80 °C. Whey protein powders of differing NaCl concentrations (0, 8, and 17 % [wt/wt]) were equilibrated to target a(w) levels 0.23, 0.33, and 0.58. Powders were inoculated with Salmonella, vacuum sealed, and stored at 70 and 80 °C for 48 h. Cells were recovered on nonselective differential media. Survival data were fit with the Weibull model, and first decimal reduction times (δ) (measured in minutes) and shape factor values (β) were estimated. The influence of temperature, a(w), and salinity on Weibull model parameters (δ and β) was analyzed using multiple linear regression. Results showed that a(w) significantly influenced the survival of Salmonella at both temperatures, increasing resistance at decreasing a(w). Sodium chloride did not provide additional protection or inactivation of Salmonella at any temperature beyond that attributed to a(w). The Weibull model described the survival kinetics of Salmonella well, with R2 adj and root mean square error values ranging from 0.59 to 0.97 and 0.27 to 1.07, respectively. Temperature and a(w) influenced δ values (P < 0.05), whereas no significant differences were found between 70 and 80 °C among the different salt concentrations (P > 0.05). β values were not significantly influenced by temperature, a(w), or % NaCl (P > 0.05). This study indicates that information on salt content in food may not help improve predictions on the

  4. Temperature resistance of Salmonella in low-water activity whey protein powder as influenced by salt content.

    PubMed

    Santillana Farakos, S M; Hicks, J W; Frank, J F

    2014-04-01

    Salmonella can survive in low-water activity (a(w)) foods for long periods of time. Water activity and the presence of solutes may affect its survival during heating. Low-a(w) products that contain sodium levels above 0.1 % (wt/wt) and that have been involved in major Salmonella outbreaks include peanut products and salty snacks. Reduced a(w) protects against thermal inactivation. There is conflicting information regarding the role of salt. The aim of this study was to determine whether NaCl influences the survival of Salmonella in low-a(w) whey protein powder independent of a(w) at 70 and 80 °C. Whey protein powders of differing NaCl concentrations (0, 8, and 17 % [wt/wt]) were equilibrated to target a(w) levels 0.23, 0.33, and 0.58. Powders were inoculated with Salmonella, vacuum sealed, and stored at 70 and 80 °C for 48 h. Cells were recovered on nonselective differential media. Survival data were fit with the Weibull model, and first decimal reduction times (δ) (measured in minutes) and shape factor values (β) were estimated. The influence of temperature, a(w), and salinity on Weibull model parameters (δ and β) was analyzed using multiple linear regression. Results showed that a(w) significantly influenced the survival of Salmonella at both temperatures, increasing resistance at decreasing a(w). Sodium chloride did not provide additional protection or inactivation of Salmonella at any temperature beyond that attributed to a(w). The Weibull model described the survival kinetics of Salmonella well, with R2 adj and root mean square error values ranging from 0.59 to 0.97 and 0.27 to 1.07, respectively. Temperature and a(w) influenced δ values (P < 0.05), whereas no significant differences were found between 70 and 80 °C among the different salt concentrations (P > 0.05). β values were not significantly influenced by temperature, a(w), or % NaCl (P > 0.05). This study indicates that information on salt content in food may not help improve predictions on the

  5. Effect of powdered activated carbon (PAC) on MBR performance and effluent trihalomethane formation: At the initial stage of PAC addition.

    PubMed

    Gao, Yue; Ma, Defang; Yue, Qinyan; Gao, Baoyu; Huang, Xia

    2016-09-01

    In this study, the MBR was used to treat municipal wastewater for reuse. Effects of powdered activated carbon (PAC) addition on MBR system in terms of effluent water quality, trihalomethane (THM) formation and membrane organic fouling tendency of MBR sludge supernatant at the initial stage of PAC addition were investigated. Effects of chlorine dose and contact time on THM formation and speciation were also studied. PAC addition enhanced the removal of organic matters, especially aromatic components, which improved the UV254 removal rate from 34% to 83%. PAC addition greatly reduced the membrane organic fouling tendency of MBR sludge supernatant. PAC addition reduced the MBR effluent trihalomethane formation potential (THMFP) from 351.29 to 241.95μg/L, while increased THM formation reactivity by 42%. PAC addition enhanced the formation of higher toxic bromine-containing THMs. High chlorine dose and contact time resulted in higher THM formation but lower proportion of bromine-containing THMs. PMID:27318162

  6. Impacts of powdered activated carbon addition on trihalomethane formation reactivity of dissolved organic matter in membrane bioreactor effluent.

    PubMed

    Ma, Defang; Gao, Yue; Gao, Baoyu; Wang, Yan; Yue, Qinyan; Li, Qian

    2014-12-01

    Characteristics and trihalomethane (THM) formation reactivity of dissolved organic matter (DOM) in effluents from two membrane bioreactors (MBRs) with and without powdered activated carbon (PAC) addition (referred to as PAC/MBR and MBR, respectively) were examined to investigate the effects of PAC addition on THM formation of MBR effluent during chlorination. PAC addition increased the specific UV absorbance. Hydrophobic DOM especially hydrophobic acids in PAC/MBR effluent (50%) were more than MBR effluent (42%). DOM with molecular weight <1 kDa constituted 12% of PAC/MBR effluent DOM, which was less than that of MBR effluent (16%). Data obtained from excitation and emission matrix fluorescence spectroscopy revealed that PAC/MBR effluent DOM contained more simple aromatic protein, but had less fulvic acid-like and soluble microbial by-product-like. PAC addition reduced the formation of bromine-containing THMs during chlorination of effluents, but increased THM formation reactivity of effluent DOM. PMID:25150685

  7. Sustainable development of tyre char-based activated carbons with different textural properties for value-added applications.

    PubMed

    Hadi, Pejman; Yeung, Kit Ying; Guo, Jiaxin; Wang, Huaimin; McKay, Gordon

    2016-04-01

    This paper aims at the sustainable development of activated carbons for value-added applications from the waste tyre pyrolysis product, tyre char, in order to make pyrolysis economically favorable. Two activation process parameters, activation temperature (900, 925, 950 and 975 °C) and residence time (2, 4 and 6 h) with steam as the activating agent have been investigated. The textural properties of the produced tyre char activated carbons have been characterized by nitrogen adsorption-desorption experiments at -196 °C. The activation process has resulted in the production of mesoporous activated carbons confirmed by the existence of hysteresis loops in the N2 adsorption-desorption curves and the pore size distribution curves obtained from BJH method. The BET surface area, total pore volume and mesopore volume of the activated carbons from tyre char have been improved to 732 m(2)/g, 0.91 cm(3)/g and 0.89 cm(3)/g, respectively. It has been observed that the BET surface area, mesopore volume and total pore volume increased linearly with burnoff during activation in the range of experimental parameters studied. Thus, yield-normalized surface area, defined as the surface area of the activated carbon per gram of the precursor, has been introduced to optimize the activation conditions. Accordingly, the optimized activation conditions have been demonstrated as an activation temperature of 975 °C and an activation time of 4 h.

  8. Sustainable development of tyre char-based activated carbons with different textural properties for value-added applications.

    PubMed

    Hadi, Pejman; Yeung, Kit Ying; Guo, Jiaxin; Wang, Huaimin; McKay, Gordon

    2016-04-01

    This paper aims at the sustainable development of activated carbons for value-added applications from the waste tyre pyrolysis product, tyre char, in order to make pyrolysis economically favorable. Two activation process parameters, activation temperature (900, 925, 950 and 975 °C) and residence time (2, 4 and 6 h) with steam as the activating agent have been investigated. The textural properties of the produced tyre char activated carbons have been characterized by nitrogen adsorption-desorption experiments at -196 °C. The activation process has resulted in the production of mesoporous activated carbons confirmed by the existence of hysteresis loops in the N2 adsorption-desorption curves and the pore size distribution curves obtained from BJH method. The BET surface area, total pore volume and mesopore volume of the activated carbons from tyre char have been improved to 732 m(2)/g, 0.91 cm(3)/g and 0.89 cm(3)/g, respectively. It has been observed that the BET surface area, mesopore volume and total pore volume increased linearly with burnoff during activation in the range of experimental parameters studied. Thus, yield-normalized surface area, defined as the surface area of the activated carbon per gram of the precursor, has been introduced to optimize the activation conditions. Accordingly, the optimized activation conditions have been demonstrated as an activation temperature of 975 °C and an activation time of 4 h. PMID:26775155

  9. Superiority of wet-milled over dry-milled superfine powdered activated carbon for adsorptive 2-methylisoborneol removal.

    PubMed

    Pan, Long; Matsui, Yoshihiko; Matsushita, Taku; Shirasaki, Nobutaka

    2016-10-01

    Superfine powdered activated carbon (SPAC), which is produced from conventionally sized powdered activated carbon (PAC) by wet milling in a bead mill, has attracted attention for its high adsorptive removal ability in both research and practice. In this study, the performance of dry-milled SPAC was investigated. 2-Methylisoborneol (MIB), an earthy-musty compound commonly targeted by water treatment systems, was used as the target adsorbate. Dry-milled SPAC exhibited lower adsorptive removal of MIB than wet-milled SPAC, even when both SPACs were produced from the same PAC and were composed of particles of the same size. One reason for the lower removal of MIB by the dry-milled SPAC was a higher degree of aggregation in the dry-milled SPAC after production; as a result the apparent particle size of dry-milled SPAC was larger than that of wet-milled SPAC. The dry-milled SPAC was also more negatively charged than the wet-milled SPAC, and, owing to its higher repulsion, it was more amenable to dispersion by ultrasonication. However, even after the dry-milled SPAC was ultrasonicated so that its apparent particle size was similar to or less than that of the wet-milled SPAC, the dry-milled SPAC was still inferior in adsorptive removal to the wet-milled SPAC. Therefore, another reason for the lower adsorptive removal of dry-milled SPAC was its lower equilibrium adsorption capacity due to the oxidation during the milling. The adsorption kinetics by SPACs with different degrees of particle aggregation were successfully simulated by a pore diffusion model and a fractal aggregation model. PMID:27403874

  10. Super-fine powdered activated carbon (SPAC) for efficient removal of micropollutants from wastewater treatment plant effluent.

    PubMed

    Bonvin, Florence; Jost, Livia; Randin, Lea; Bonvin, Emmanuel; Kohn, Tamar

    2016-03-01

    In an effort to mitigate the discharge of micropollutants to surface waters, adsorption of micropollutants onto powdered activated carbon (PAC) after conventional wastewater treatment has been identified as a promising technology for enhanced removal of pharmaceuticals and pesticides from wastewater. We investigated the effectiveness of super-fine powdered activated carbon, SPAC, (ca. 1 μm mean particle diameter) in comparison to regular-sized PAC (17-37 μm mean diameter) for the optimization of micropollutant removal from wastewater. Adsorption isotherms and batch kinetic experiments were performed for 10 representative micropollutants (bezafibrate, benzotriazole, carbamazepine, diclofenac, gabapentin, mecoprop, metoprolol, ofloxacin, sulfamethoxazole and trimethoprim) onto three commercial PACs and their super-fine variants in carbonate buffer and in wastewater effluent. SPAC showed substantially faster adsorption kinetics of all micropollutants than conventional PAC, regardless of the micropollutant adsorption affinity and the solution matrix. The total adsorptive capacities of SPAC were similar to those of PAC for two of the three tested carbon materials, in all tested waters. However, in effluent wastewater, the presence of effluent organic matter adversely affected micropollutant removal, resulting in lower removal efficiencies especially for micropollutants with low affinity for adsorbent particles in comparison to pure water. In comparison to PAC, SPAC application resulted in up to two-fold enhanced dissolved organic carbon (DOC) removal from effluent wastewater. The more efficient adsorption process using SPAC translates into a reduction of contact time and contact tank size as well as reduced carbon dosing for a targeted micropollutant removal. In the tested effluent wastewater (5 mg/L DOC), the necessary dose to achieve 80% average removal of indicator micropollutants (benzotriazole, diclofenac, carbamazepine, mecoprop and sulfamethoxazole) ranged

  11. Super-fine powdered activated carbon (SPAC) for efficient removal of micropollutants from wastewater treatment plant effluent.

    PubMed

    Bonvin, Florence; Jost, Livia; Randin, Lea; Bonvin, Emmanuel; Kohn, Tamar

    2016-03-01

    In an effort to mitigate the discharge of micropollutants to surface waters, adsorption of micropollutants onto powdered activated carbon (PAC) after conventional wastewater treatment has been identified as a promising technology for enhanced removal of pharmaceuticals and pesticides from wastewater. We investigated the effectiveness of super-fine powdered activated carbon, SPAC, (ca. 1 μm mean particle diameter) in comparison to regular-sized PAC (17-37 μm mean diameter) for the optimization of micropollutant removal from wastewater. Adsorption isotherms and batch kinetic experiments were performed for 10 representative micropollutants (bezafibrate, benzotriazole, carbamazepine, diclofenac, gabapentin, mecoprop, metoprolol, ofloxacin, sulfamethoxazole and trimethoprim) onto three commercial PACs and their super-fine variants in carbonate buffer and in wastewater effluent. SPAC showed substantially faster adsorption kinetics of all micropollutants than conventional PAC, regardless of the micropollutant adsorption affinity and the solution matrix. The total adsorptive capacities of SPAC were similar to those of PAC for two of the three tested carbon materials, in all tested waters. However, in effluent wastewater, the presence of effluent organic matter adversely affected micropollutant removal, resulting in lower removal efficiencies especially for micropollutants with low affinity for adsorbent particles in comparison to pure water. In comparison to PAC, SPAC application resulted in up to two-fold enhanced dissolved organic carbon (DOC) removal from effluent wastewater. The more efficient adsorption process using SPAC translates into a reduction of contact time and contact tank size as well as reduced carbon dosing for a targeted micropollutant removal. In the tested effluent wastewater (5 mg/L DOC), the necessary dose to achieve 80% average removal of indicator micropollutants (benzotriazole, diclofenac, carbamazepine, mecoprop and sulfamethoxazole) ranged

  12. Powder sampling.

    PubMed

    Venables, Helena J; Wells, J I

    2002-01-01

    The factors involved when sampling powder mixes have been reviewed. The various methods are evaluated (manual, automatic, and sub-sampling) and the errors incurred are discussed. Certain rules have been applied to various samplers and their suitability for powder mixtures are described. The spinning riffler is apparently the most suitable, while the use of sample thieves should be avoided due to error and bias.

  13. In Situ Production of Fe-TiC Nanocomposite by Mechanical Activation and Heat Treatment of the Fe2O3/TiO2/C Powder

    NASA Astrophysics Data System (ADS)

    Moradi Ghiasabadi, Sara; Raygan, Shahram

    2012-11-01

    In this study, Fe-TiC nanocomposite was synthesized by carbothermic reduction of activated Fe2O3, TiO2, and graphite powder mixture. The effect of 0, 5, and 20 h of high energy ball milling of mixture on the reduction process was also investigated. Comparing the results of the thermogravimetry analysis of milled and un-milled mixtures clearly showed that the reduction temperature decreased due to the milling process. XRD pattern of 20 h milled powder mixture proved that Fe-TiC nanocomposite was formed after the heat treatment of activated powder at 1100°C for 1 h under vacuum. The microstructure studies of the milled mixture by scanning electron microscope revealed homogenous distribution of TiC particles in the Fe matrix.

  14. Neem (Azadirachta indica) seed kernel powder retards urease and nitrification activities in different soils at contrasting moisture and temperature regimes.

    PubMed

    Mohanty, Sangita; Patra, Ashok K; Chhonkar, Pramod K

    2008-03-01

    A laboratory experiment was conducted to examine the potentiality of a natural resource neem (Azadirachta indica) seed kernel powder (NSKP) to reduce the urease and nitrification activities in different soils (viz., normal, acid, and sodic) at contrasting moisture (1:1 soil to water and field capacity) and temperature regimes (10 degrees C and 37 degrees C). Results have revealed that application of NSKP with urea did not exhibit any urease inhibitory property in normal and sodic soils, but in acid soil it had maintained higher concentration of urea than the urea alone treated samples for two weeks after application. At 37 degrees C and under field capacity moisture level, urea hydrolysis was more rapid than at 10 degrees C and under waterlogged (1:1) conditions. The NSKP has showed variable effects (4-28%) to inhibit nitrification during 7-21 days after application, depending upon the soil types, temperature and moisture regimes. The nitrification activity was significantly low in acid soil followed by normal and sodic soils. The present study suggests that NSKP has the potential to retard the urease activity in acid soil, and nitrification in all the soils, and thus it may be used along with urea for the better use of applied -N. PMID:17360179

  15. Anti-Helicobacter Pylori Activities of Shoya Powder and Essential Oils of Thymus Vulgaris and Eucalyptus Globulus

    PubMed Central

    Esmaeili, D; Mobarez, A Mohabati; Tohidpour, A

    2012-01-01

    Background: Helicobacter pylori, an infective agent of more than 50% of the world population is prominent to be the main causative factor in the etiologies of chronic, active or type B gastritis, peptic and duodenal ulcer, gastric carcinoma, and mucosa-associated lymphoid tumors. A high prevalence of this bacterium in dental plaque is always reported. Pharmacological treatment of H. pylori infections includes administration of 3-fold therapeutic regimens which are typically used to suppress H. pylori activity. However, antibiotic resistance frequently develops as a consequence of such treatment. Thus, searching for alternative therapies for H. pylori infections is of special interest. Materials and Methods: In this study, anti H. pylori activities of a traditional antimicrobial drug so-called Shoya and also essential oils of Thymus vulgaris and Eucalyptus globulus were investigated using antimicrobial analysis and serological screening methods. Results: The agar dilution method results revealed the Shoya with the highest inhibitory effect against H. pylori. Also serological screening on tested mice showed a significant effect of this drug in lowering the sera amount of anti H. pylori specific IgA and IgG titers. Both of the essential oils showed different degrees of antibacterial effect against H. pylori. Conclusion: The obtained results showed the antibacterial effect of Shoya powder and Essential oils from Thymus vulgaris and Eucalyptus globulus and purposes new therapeutical alternatives to control the H. pylori infection. Additional studies and clinical trials are necessary to approve the use of these data in health care and pharmacopeia systems. PMID:22927892

  16. Fabricating solid carbon porous electrodes from powders

    DOEpatents

    Kaschmitter, James L.; Tran, Tri D.; Feikert, John H.; Mayer, Steven T.

    1997-01-01

    Fabrication of conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive dionization, and waste treatment. Electrodes fabricated from low surface area (<50 m.sup.2 /gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon compositives with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to be high surface area carbons, fuel cell electrodes can be produced.

  17. Fabricating solid carbon porous electrodes from powders

    DOEpatents

    Kaschmitter, J.L.; Tran, T.D.; Feikert, J.H.; Mayer, S.T.

    1997-06-10

    Fabrication is described for conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive deionization, and waste treatment. Electrodes fabricated from low surface area (<50 m{sup 2}/gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon composites with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to high surface area carbons, fuel cell electrodes can be produced. 1 fig.

  18. Demystifying Mystery Powders.

    ERIC Educational Resources Information Center

    Kotar, Michael

    1989-01-01

    Describes science activities which use simple chemical tests to distinguish between materials and to determine some of their properties. Explains the water, iodine, heat, acid, baking soda, acid/base indicator, glucose, and sugar tests. Includes activities to enhance chemical testing and a list of suggested powders for use. (RT)

  19. Lack of leptin activity in blood samples of Adélie penguin and bar-tailed godwit.

    PubMed

    Yosefi, Sara; Hen, Gideon; Rosenblum, Charles I; Cerasale, David J; Beaulieu, Michaël; Criscuolo, Francois; Friedman-Einat, Miriam

    2010-10-01

    Unsuccessful attempts to identify the leptin gene in birds are well documented, despite the characterization of its receptor (LEPR). Since leptin and LEPR have poor sequence conservation among vertebrates, we speculated that a functional assay should represent the best way to detect leptin in birds. Using a leptin bioassay that is based on activation of the chicken LEPR in cultured cells, blood samples from wild birds with extreme seasonal variation in voluntary food intake and fat deposition (Adélie penguins and bar-tailed godwits) were tested for leptin activity. In these experiments, blood samples collected during the pre-incubation and the chick-rearing periods of Adélie penguins, and during the migratory flight and refueling stages of bar-tailed godwits, were found to contain no detectable leptin activity, while the sensitivity of the assay to activation by human blood samples from donor subjects representing a variety of body mass indices and fat contents was clearly demonstrated. These results suggest that in birds, an alternative control mechanism to that of mammals operates in the communication between the body fat tissues and the central control on energy homeostasis.

  20. Salt stress in a membrane bioreactor: dynamics of sludge properties, membrane fouling and remediation through powdered activated carbon dosing.

    PubMed

    De Temmerman, L; Maere, T; Temmink, H; Zwijnenburg, A; Nopens, I

    2014-10-15

    Membrane bioreactors are a well-established technology for wastewater treatment. However, their efficiency is adversely impacted by membrane fouling, primarily inciting very conservative operations of installations that makes them less appealing from an economic perspective. This fouling propensity of the activated sludge is closely related to system disturbances. Therefore, improved insight into the impact of fouling is crucial towards increased membrane performance. In this work, the disturbance of a salt shock was investigated with respect to sludge composition and filterability in two parallel lab-scale membrane bioreactors. Several key sludge parameters (soluble microbial products, sludge-bound extracellular polymeric substances, supramicron particle size distributions (PSD), submicron particle concentrations) were intensively monitored prior to, during, and after a disturbance to investigate its impact as well as the potential governing mechanism. Upon salt addition, the supramicron PSD immediately shifted to smaller floc sizes, and the total fouling rate increased. Following a certain delay, an increase in submicron particles, supernatant proteins, and polysaccharides was observed as well as an increase in the irreversible membrane fouling rate. Recovery from the disturbance was evidenced with a simultaneous decrease in the above mentioned quantities. A similar experiment introducing powdered activated carbon (PAC) addition used for remediation resulted in either no or less significant changes in the above mentioned quantities, signifying its potential as a mitigation strategy.

  1. Where to dose powdered activated carbon in a wastewater treatment plant for organic micro-pollutant removal.

    PubMed

    Streicher, Judith; Ruhl, Aki Sebastian; Gnirß, Regina; Jekel, Martin

    2016-08-01

    Emissions of many organic micro-pollutants (OMP) into the aquatic environment can be efficiently reduced with advanced treatment at wastewater treatment plants (WWTP). Post-treatment with activated carbon is currently considered as one of the most promising options, but powdered activated carbon (PAC) could also be dosed into the existing biological treatment process instead. Due to much greater concentrations of suspended and dissolved constituents the adsorptive OMP removal was expected to be severely hindered. Systematic comparative adsorption tests with samples from different process steps of a large conventional WWTP were conducted to investigate differences in adsorption competition and removal efficiencies. The results show that much greater competition occurs in the WWTP influent and in the anaerobic tank but removal efficiencies in the anoxic and aerobic tank and in the WWTP effluent were more similar than expected. Suspended solids thus seem not to severely affect OMP adsorption. Similar results were obtained in a comparison of different commercial PAC in all for the respective matrices. OMP removals showed a relation with the PAC dosage normalized to the concentration of dissolved organic carbon. In the anoxic and aerobic tank and in the WWTP effluent, a uniform correlation of OMP removals and reductions of UV light absorption was observed. PMID:27174820

  2. Bioturbation and dissolved organic matter enhance contaminant fluxes from sediment treated with powdered and granular activated carbon.

    PubMed

    Kupryianchyk, D; Noori, A; Rakowska, M I; Grotenhuis, J T C; Koelmans, A A

    2013-05-21

    Sediment amendment with activated carbon (AC) is a promising technique for in situ sediment remediation. To date it is not clear whether this technique sufficiently reduces sediment-to-water fluxes of sediment-bound hydrophobic organic chemicals (HOCs) in the presence of bioturbators. Here, we report polychlorobiphenyl (PCB) pore water concentrations, fluxes, mass transfer coefficients, and survival data of two benthic species, for four treatments: no AC addition (control), powdered AC addition, granular AC addition and addition and subsequent removal of GAC (sediment stripping). AC addition decreased mass fluxes but increased apparent mass transfer coefficients because of dissolved organic carbon (DOC) facilitated transport across the benthic boundary layer (BBL). In turn, DOC concentrations depended on bioturbator activity which was high for the PAC tolerant species Asellus aquaticus and low for AC sensitive species Lumbriculus variegatus. A dual BBL resistance model combining AC effects on gradients, DOC facilitated transport and biodiffusion was evaluated against the data and showed how the type of resistance differs with treatment and chemical hydrophobicity. Data and simulations illustrate the complex interplay between AC and contaminant toxicity to benthic organisms and how differences in species tolerance affect mass fluxes from sediment to the water column. PMID:23590290

  3. Direct comparison of ozonation and adsorption onto powdered activated carbon for micropollutant removal in advanced wastewater treatment.

    PubMed

    Altmann, Johannes; Ruhl, Aki Sebastian; Zietzschmann, Frederik; Jekel, Martin

    2014-05-15

    Organic micropollutants (OMPs) may occur ubiquitously in the aquatic environment. In order to protect the ecosystem and drinking water sources from potentially toxic effects, discharges of an increasing number of OMPs are being regulated. OMP removal from wastewater treatment plant (WWTP) effluents as a point source is a preferred option with removal by adsorption onto powdered activated carbon (PAC) and OMP transformation to presumably harmless compounds by ozonation as the most promising techniques. In this study, effluents of four WWTPs were treated with PAC and ozone in bench-scale experiments to compare the removal efficiencies of seven relevant OMPs. Concentrations of carbamazepine and diclofenac were reduced by more than 90% with 20 mg/L PAC or 5-7 mg/L ozone (0.5 mg O3 per mg dissolved organic carbon (DOC)). Comparing typical doses for practical applications ozonation proved to be more efficient for abatement of sulfamethoxazole, while removal of benzotriazole and iomeprol was comparatively more efficient with activated carbon. While well known for ozonation, DOC-normalized doses were also applied to PAC and correlated better to relative OMP removal than volume proportional PAC addition. Furthermore, OMP removal efficiencies corresponded well with the reduction of ultraviolet light absorption at 254 nm for both treatment options. PMID:24607314

  4. Salt stress in a membrane bioreactor: dynamics of sludge properties, membrane fouling and remediation through powdered activated carbon dosing.

    PubMed

    De Temmerman, L; Maere, T; Temmink, H; Zwijnenburg, A; Nopens, I

    2014-10-15

    Membrane bioreactors are a well-established technology for wastewater treatment. However, their efficiency is adversely impacted by membrane fouling, primarily inciting very conservative operations of installations that makes them less appealing from an economic perspective. This fouling propensity of the activated sludge is closely related to system disturbances. Therefore, improved insight into the impact of fouling is crucial towards increased membrane performance. In this work, the disturbance of a salt shock was investigated with respect to sludge composition and filterability in two parallel lab-scale membrane bioreactors. Several key sludge parameters (soluble microbial products, sludge-bound extracellular polymeric substances, supramicron particle size distributions (PSD), submicron particle concentrations) were intensively monitored prior to, during, and after a disturbance to investigate its impact as well as the potential governing mechanism. Upon salt addition, the supramicron PSD immediately shifted to smaller floc sizes, and the total fouling rate increased. Following a certain delay, an increase in submicron particles, supernatant proteins, and polysaccharides was observed as well as an increase in the irreversible membrane fouling rate. Recovery from the disturbance was evidenced with a simultaneous decrease in the above mentioned quantities. A similar experiment introducing powdered activated carbon (PAC) addition used for remediation resulted in either no or less significant changes in the above mentioned quantities, signifying its potential as a mitigation strategy. PMID:24999116

  5. Where to dose powdered activated carbon in a wastewater treatment plant for organic micro-pollutant removal.

    PubMed

    Streicher, Judith; Ruhl, Aki Sebastian; Gnirß, Regina; Jekel, Martin

    2016-08-01

    Emissions of many organic micro-pollutants (OMP) into the aquatic environment can be efficiently reduced with advanced treatment at wastewater treatment plants (WWTP). Post-treatment with activated carbon is currently considered as one of the most promising options, but powdered activated carbon (PAC) could also be dosed into the existing biological treatment process instead. Due to much greater concentrations of suspended and dissolved constituents the adsorptive OMP removal was expected to be severely hindered. Systematic comparative adsorption tests with samples from different process steps of a large conventional WWTP were conducted to investigate differences in adsorption competition and removal efficiencies. The results show that much greater competition occurs in the WWTP influent and in the anaerobic tank but removal efficiencies in the anoxic and aerobic tank and in the WWTP effluent were more similar than expected. Suspended solids thus seem not to severely affect OMP adsorption. Similar results were obtained in a comparison of different commercial PAC in all for the respective matrices. OMP removals showed a relation with the PAC dosage normalized to the concentration of dissolved organic carbon. In the anoxic and aerobic tank and in the WWTP effluent, a uniform correlation of OMP removals and reductions of UV light absorption was observed.

  6. Direct comparison of ozonation and adsorption onto powdered activated carbon for micropollutant removal in advanced wastewater treatment.

    PubMed

    Altmann, Johannes; Ruhl, Aki Sebastian; Zietzschmann, Frederik; Jekel, Martin

    2014-05-15

    Organic micropollutants (OMPs) may occur ubiquitously in the aquatic environment. In order to protect the ecosystem and drinking water sources from potentially toxic effects, discharges of an increasing number of OMPs are being regulated. OMP removal from wastewater treatment plant (WWTP) effluents as a point source is a preferred option with removal by adsorption onto powdered activated carbon (PAC) and OMP transformation to presumably harmless compounds by ozonation as the most promising techniques. In this study, effluents of four WWTPs were treated with PAC and ozone in bench-scale experiments to compare the removal efficiencies of seven relevant OMPs. Concentrations of carbamazepine and diclofenac were reduced by more than 90% with 20 mg/L PAC or 5-7 mg/L ozone (0.5 mg O3 per mg dissolved organic carbon (DOC)). Comparing typical doses for practical applications ozonation proved to be more efficient for abatement of sulfamethoxazole, while removal of benzotriazole and iomeprol was comparatively more efficient with activated carbon. While well known for ozonation, DOC-normalized doses were also applied to PAC and correlated better to relative OMP removal than volume proportional PAC addition. Furthermore, OMP removal efficiencies corresponded well with the reduction of ultraviolet light absorption at 254 nm for both treatment options.

  7. Preparation of Active Proteins, Vaccines and Pharmaceuticals as Fine Powders using Supercritical or Near-Critical Fluids

    PubMed Central

    Villa, Joseph A.; Huang, Edward T. S.; Yang, Tzung-Horng; Carpenter, John F.; Sievers, Robert E.

    2008-01-01

    Supercritical or near-critical fluid processes for generating microparticles have enjoyed considerable attention in the past decade or so, with good success for substances soluble in supercritical fluids or organic solvents. In this review, we survey their application to the production of protein particles. A recently developed process known as CO2-assisted nebulization with a Bubble Dryer® (CAN-BD) has been demonstrated to have broad applicability to small-molecule as well as macromolecule substances (including therapeutic proteins). The principles of CAN-BD are discussed as well as the stabilization, micronization and drying of a wide variety of materials. More detailed case studies are presented for three proteins, two of which are of therapeutic interest: anti-CD4 antibody (rheumatoid arthritis), α1-antitrypsin (cystic fibrosis and emphysema), and trypsinogen (a model enzyme). Dry powders were formed in which stability and activity are maintained and which are fine enough to be inhaled and reach the deep lung. Enhancement of apparent activity after CAN-BD processing was also observed in some formulation and processing conditions. PMID:18581212

  8. Promoted degradation of perfluorooctanic acid by persulfate when adding activated carbon.

    PubMed

    Lee, Yu-Chi; Lo, Shang-Lien; Kuo, Jeff; Huang, Chin-Pao

    2013-10-15

    Treatment of persistent perfluorooctanoic acid (PFOA) in water using persulfate (PS) oxidation typically requires an elevated temperature or UV irradiation, which is energy-consuming. Under relatively low temperatures of 25-45°C, activated carbon (AC) activated PS oxidation of PFOA was evaluated for its potential of practical applications. With presence of AC in PS oxidation, PFOA removal efficiency at 25°C reached 682% with a high defluorination efficiency of 549% after 12h and few intermediates of short-chain perfluorinated carboxylic acids (PFCAs) were found. The removal and defluorination rates with the combined AC/PS system were approximately 12 and 19 times higher than those of the PS-only system, respectively. Activated carbon not only removes PFOA through adsorption, but also activates PS to form sulfate radicals that accelerate the decomposition and mineralization of PFOA. The activation energy for PS oxidation of PFOA was reduced from 668 to 261kJ/mol by the catalytic effect of AC, which implies a lower reaction temperature and a shorter reaction time would suffice. A 2-cycle schematic reaction mechanism was used to describe PS oxidation of PFOA with the generation of various intermediates and end-products.

  9. pH dependent antioxidant activity of lettuce (L. sativa) and synergism with added phenolic antioxidants.

    PubMed

    Altunkaya, Arzu; Gökmen, Vural; Skibsted, Leif H

    2016-01-01

    Influence of pH on the antioxidant activities of combinations of lettuce extract (LE) with quercetin (QC), green tea extract (GTE) or grape seed extract (GSE) was investigated for both reduction of Fremy's salt in aqueous solution using direct electron spin resonance (ESR) spectroscopy and in L-α-phosphatidylcholine liposome peroxidation assay measured following formation of conjugated dienes. All examined phenolic antioxidants showed increasing radical scavenging effect with increasing pH values by using both methods. QC, GTE and GSE acted synergistically in combination with LE against oxidation of peroxidating liposomes and with QC showing the largest effect. The pH dependent increase of the antioxidant activity of the phenols is due to an increase of their electron-donating ability upon deprotonation and to their stabilization in alkaline solutions leading to polymerization reaction. Such polymerization reactions of polyphenolic antioxidants can form new oxidizable -OH moieties in their polymeric products resulting in a higher radical scavenging activity.

  10. pH dependent antioxidant activity of lettuce (L. sativa) and synergism with added phenolic antioxidants.

    PubMed

    Altunkaya, Arzu; Gökmen, Vural; Skibsted, Leif H

    2016-01-01

    Influence of pH on the antioxidant activities of combinations of lettuce extract (LE) with quercetin (QC), green tea extract (GTE) or grape seed extract (GSE) was investigated for both reduction of Fremy's salt in aqueous solution using direct electron spin resonance (ESR) spectroscopy and in L-α-phosphatidylcholine liposome peroxidation assay measured following formation of conjugated dienes. All examined phenolic antioxidants showed increasing radical scavenging effect with increasing pH values by using both methods. QC, GTE and GSE acted synergistically in combination with LE against oxidation of peroxidating liposomes and with QC showing the largest effect. The pH dependent increase of the antioxidant activity of the phenols is due to an increase of their electron-donating ability upon deprotonation and to their stabilization in alkaline solutions leading to polymerization reaction. Such polymerization reactions of polyphenolic antioxidants can form new oxidizable -OH moieties in their polymeric products resulting in a higher radical scavenging activity. PMID:26212937

  11. Immobilized acclimated biomass-powdered activated carbon for the bioregeneration of granular activated carbon loaded with phenol and o-cresol.

    PubMed

    Toh, Run-Hong; Lim, Poh-Eng; Seng, Chye-Eng; Adnan, Rohana

    2013-09-01

    The objectives of the study are to use immobilized acclimated biomass and immobilized biomass-powdered activated carbon (PAC) as a novel approach in the bioregeneration of granular activated carbon (GAC) loaded with phenol and o-cresol, respectively, and to compare the efficiency and rate of the bioregeneration of the phenolic compound-loaded GAC using immobilized and suspended biomasses under varying GAC dosages. Bioregeneration of GAC loaded with phenol and o-cresol, respectively, was conducted in batch system using the sequential adsorption and biodegradation approach. The results showed that the bioregeneration efficiency of GAC loaded with phenol or o-cresol was basically the same irrespective of whether the immobilized or suspended biomass was used. Nonetheless, the duration for bioregeneration was longer under immobilized biomass. The beneficial effect of immobilized PAC-biomass for bioregeneration is the enhancement of the removal rate of the phenolic compounds via adsorption and the shortening of the bioregeneration duration. PMID:23796608

  12. Antioxidant activity, total phenolics content, anthocyanin, and color stability of isotonic model beverages colored with Andes berry (Rubus glaucus Benth) anthocyanin powder.

    PubMed

    Estupiñan, D C; Schwartz, S J; Garzón, G A

    2011-01-01

    The stability of anthocyanin (ACN) freeze-dried powders from Andes berry (Rubus glaucus Benth) as affected by storage, addition of maltodextrin as a carrier agent, and illumination was evaluated in isotonic model beverages. The ethanolic ACN extract was freeze dried with and without maltodextrin DE 20. Isotonic model beverages were colored with freeze-dried ACN powder (FDA), freeze-dried ACN powder with maltodextrin (MFDA), and red nr 40. Beverages were stored in the dark and under the effect of illumination. Half life of the ACNs, changes in color, total phenolics content (TPC), and antioxidant activity were analyzed for 71 d. Addition of maltodextrin and absence of light stabilized the color of beverages and improved ACN and TPC stability during storage. The antioxidant activity of the beverages was higher when they were colored with MFDA and highly correlated with ACN content. There was no correlation between antioxidant activity and TPC. It is concluded that addition of maltodextrin DE 20 as a carrier agent during freeze-drying improves the color and stability of nutraceutical antioxidants present in Andes berry extract. This suggests a protective enclosing of ACNs within a maltodextrin matrix with a resulting powder that could serve as a supplement or additive to naturally color and to enhance the antioxidant capacity of isotonic beverages.

  13. Antioxidant Activity, Total Phenolics Content, Anthocyanin, and Color Stability of Isotonic Model Beverages Colored with Andes Berry (Rubus glaucus Benth) Anthocyanin Powder

    PubMed Central

    Estupiñan, D.C.; Schwartz, S.J.; Garzón, G.A.

    2013-01-01

    The stability of anthocyanin (ACN) freeze-dried powders from Andes berry (Rubus glaucus Benth) as affected by storage, addition of maltodextrin as a carrier agent, and illumination was evaluated in isotonic model beverages. The ethanolic ACN extract was freeze dried with and without maltodextrin DE 20. Isotonic model beverages were colored with freeze-dried ACN powder (FDA), freeze-dried ACN powder with maltodextrin (MFDA), and red nr 40. Beverages were stored in the dark and under the effect of illumination. Half life of the ACNs, changes in color, total phenolics content (TPC), and antioxidant activity were analyzed for 71 d. Addition of maltodextrin and absence of light stabilized the color of beverages and improved ACN and TPC stability during storage. The antioxidant activity of the beverages was higher when they were colored with MFDA and highly correlated with ACN content. There was no correlation between antioxidant activity and TPC. It is concluded that addition of maltodextrin DE 20 as a carrier agent during freeze-drying improves the color and stability of nutraceutical antioxidants present in Andes berry extract. This suggests a protective enclosing of ACNs within a maltodextrin matrix with a resulting powder that could serve as a supplement or additive to naturally color and to enhance the antioxidant capacity of isotonic beverages. PMID:21535712

  14. Artificial neural network and multiple regression model for nickel(II) adsorption on powdered activated carbons.

    PubMed

    Hema, M; Srinivasan, K

    2011-07-01

    Nickel removal efficiency of powered activated carbons of coconut oilcake, neem oilcake and commercial carbon was investigated by using artificial neural network. The effective parameters for the removal of nickel (%R) by adsorption process, which included the pH, contact time (T), distinctiveness of activated carbon (Cn), amount of activated carbon (Cw) and initial concentration of nickel (Co) were investigated. Levenberg-Marquardt (LM) Back-propagation algorithm is used to train the network. The network topology was optimized by varying number of hidden layer and number of neurons in hidden layer. The model was developed in terms of training; validation and testing of experimental data, the test subsets that each of them contains 60%, 20% and 20% of total experimental data, respectively. Multiple regression equation was developed for nickel adsorption system and the output was compared with both simulated and experimental outputs. Standard deviation (SD) with respect to experimental output was quite higher in the case of regression model when compared with ANN model. The obtained experimental data best fitted with the artificial neural network. PMID:23029923

  15. Adding Value: Using On-Line Activities To Ensure Student Success.

    ERIC Educational Resources Information Center

    Richards, Griff; Fong, Rosamaria

    This paper describes a Web site containing activities for chemistry that aid student learning. Used as an adjunct to the normal classroom and laboratory sessions, instructional goals of the Web site were to provide guidance and encourage regular and timely study. Initially learners were able to review the weekly objectives, see short explanations…

  16. Student Activism -- and Involvement in the Educational Program. Federation AdHoc Committee Report, January, 1970.

    ERIC Educational Resources Information Center

    New Jersey State Federation of District Boards of Education, Trenton.

    This report notes that (1) activism is preferable to apathy, (2) larger problems loom for schools that fail to involve parents and community, (3) board member and administrator rigidity can cause conflict, and (4) black and Spanish-speaking students have special problems. Recommendations for school administrators and teachers emphasize sincerity…

  17. Improvements to the FATOLA computer program including added actively controlled landing gear subroutines

    NASA Technical Reports Server (NTRS)

    Mall, G. H.

    1983-01-01

    Modifications to a multi-degree-of-freedom flexible aircraft take-off and landing analysis (FATOLA) computer program, including a provision for actively controlled landing gears to expand the programs simulation capabilities, are presented. Supplemental instructions for preparation of data and for use of the modified program are included.

  18. The Perception of Communication Related Value-Added Educational Activities: A Survey of Graduate Business Students

    ERIC Educational Resources Information Center

    Barker, Randolph T.; Stowers, Robert H.

    2007-01-01

    The purpose of this article is to evaluate value-add methods and activities applied to organizational communication college-level course work. Graduate organizational communication faculty are aware that their classes serve as direct preparation for students entering business and professional careers. The knowledge learned and the skills acquired…

  19. Antioxidant Enzyme Activity and Meat Quality of Meat Type Ducks Fed with Dried Oregano (Origanum vulgare L.) Powder

    PubMed Central

    Park, J. H.; Kang, S. N.; Shin, D.; Shim, K. S.

    2015-01-01

    One-day-old Cherry valley meat-strain ducks were used to investigate the effect of supplemental dried oregano powder (DOP) in feed on the productivity, antioxidant enzyme activity, and breast meat quality. One hundred sixty five ducks were assigned to 5 dietary treatments for 42 days. The dietary treatment groups were control group (CON; no antibiotic, no DOP), antibiotic group (ANT; CON+0.1% Patrol), 0.1% DOP (CON+0.1% DOP), 0.5% DOP (CON+0.5% DOP), and 1.0% DOP (CON+1.0% DOP). Upon feeding, 1,1-diphenyl-2-picryl-hydrazyl (DPPH) radical scavenging activity of oregano extracts was higher than that of tocopherol, although it was less than that of ascorbic acid. As a result of in vivo study, DOP in the diet showed no effects on final body weight, feed intake, or feed conversion ratio. However, dietary 0.5% and 1% DOP supplementation caused a significant increase in the serum enzyme activity of superoxide dismutase (SOD) compared with CON and ANT, while glutathione peroxidase (GPx) in tissue was increased as compared to ANT (p<0.05). Cooking loss from ducks fed with DOP decreased compared with the control ducks. Thiobarbituric acid reactive substance (TBARS) values of duck breast meat at 5 d post slaughter was found to be significantly reduced in ducks whose diets were supplemented with 0.5% and 1% DOP (p<0.05). These results suggest that diets containing 0.5% and 1% DOP may beneficially affect antioxidant enzyme activity of GPx and SOD, improve meat cooking loss, and reduce TBARS values in breast meat at 5 d of storage in ducks. PMID:25557678

  20. Characteristics of competitive adsorption between 2-methylisoborneol and natural organic matter on superfine and conventionally sized powdered activated carbons.

    PubMed

    Matsui, Yoshihiko; Yoshida, Tomoaki; Nakao, Soichi; Knappe, Detlef R U; Matsushita, Taku

    2012-10-01

    When treating water with activated carbon, natural organic matter (NOM) is not only a target for adsorptive removal but also an inhibitory substance that reduces the removal efficiency of trace compounds, such as 2-methylisoborneol (MIB), through adsorption competition. Recently, superfine (submicron-sized) activated carbon (SPAC) was developed by wet-milling commercially available powdered activated carbon (PAC) to a smaller particle size. It was reported that SPAC has a larger NOM adsorption capacity than PAC because NOM mainly adsorbs close to the external adsorbent particle surface (shell adsorption mechanism). Thus, SPAC with its larger specific external surface area can adsorb more NOM than PAC. The effect of higher NOM uptake on the adsorptive removal of MIB has, however, not been investigated. Results of this study show that adsorption competition between NOM and MIB did not increase when NOM uptake increased due to carbon size reduction; i.e., the increased NOM uptake by SPAC did not result in a decrease in MIB adsorption capacity beyond that obtained as a result of NOM adsorption by PAC. A simple estimation method for determining the adsorbed amount of competing NOM (NOM that reduces MIB adsorption) is presented based on the simplified equivalent background compound (EBC) method. Furthermore, the mechanism of adsorption competition is discussed based on results obtained with the simplified EBC method and the shell adsorption mechanism. Competing NOM, which likely comprises a small portion of NOM, adsorbs in internal pores of activated carbon particles as MIB does, thereby reducing the MIB adsorption capacity to a similar extent regardless of adsorbent particle size. SPAC application can be advantageous because enhanced NOM removal does not translate into less effective removal of MIB. Molecular size distribution data of NOM suggest that the competing NOM has a molecular weight similar to that of the target compound. PMID:22763287

  1. Antioxidant Enzyme Activity and Meat Quality of Meat Type Ducks Fed with Dried Oregano (Origanum vulgare L.) Powder.

    PubMed

    Park, J H; Kang, S N; Shin, D; Shim, K S

    2015-01-01

    One-day-old Cherry valley meat-strain ducks were used to investigate the effect of supplemental dried oregano powder (DOP) in feed on the productivity, antioxidant enzyme activity, and breast meat quality. One hundred sixty five ducks were assigned to 5 dietary treatments for 42 days. The dietary treatment groups were control group (CON; no antibiotic, no DOP), antibiotic group (ANT; CON+0.1% Patrol), 0.1% DOP (CON+0.1% DOP), 0.5% DOP (CON+0.5% DOP), and 1.0% DOP (CON+1.0% DOP). Upon feeding, 1,1-diphenyl-2-picryl-hydrazyl (DPPH) radical scavenging activity of oregano extracts was higher than that of tocopherol, although it was less than that of ascorbic acid. As a result of in vivo study, DOP in the diet showed no effects on final body weight, feed intake, or feed conversion ratio. However, dietary 0.5% and 1% DOP supplementation caused a significant increase in the serum enzyme activity of superoxide dismutase (SOD) compared with CON and ANT, while glutathione peroxidase (GPx) in tissue was increased as compared to ANT (p<0.05). Cooking loss from ducks fed with DOP decreased compared with the control ducks. Thiobarbituric acid reactive substance (TBARS) values of duck breast meat at 5 d post slaughter was found to be significantly reduced in ducks whose diets were supplemented with 0.5% and 1% DOP (p<0.05). These results suggest that diets containing 0.5% and 1% DOP may beneficially affect antioxidant enzyme activity of GPx and SOD, improve meat cooking loss, and reduce TBARS values in breast meat at 5 d of storage in ducks.

  2. Hairy AdS solitons

    NASA Astrophysics Data System (ADS)

    Anabalón, Andrés; Astefanesei, Dumitru; Choque, David

    2016-11-01

    We construct exact hairy AdS soliton solutions in Einstein-dilaton gravity theory. We examine their thermodynamic properties and discuss the role of these solutions for the existence of first order phase transitions for hairy black holes. The negative energy density associated to hairy AdS solitons can be interpreted as the Casimir energy that is generated in the dual filed theory when the fermions are antiperiodic on the compact coordinate.

  3. Thermodynamic and kinetic behaviors of trinitrotoluene adsorption on powdered activated carbons

    SciTech Connect

    Lee, J.W.; Hwang, K.J.; Shim, W.G.; Moon, I.S.

    2006-07-01

    Regulations on the removal of trinitrotoluene (TNT) from wastewater have become increasingly more stringent, demanding faster, less expensive, and more efficient treatment. This study focuses on the adsorption equilibrium and kinetics of TNT on powered activated carbons (PAC). Three types of PACs (i.e., wood based, coal based, and coconut-shell based) were studied as functions of temperature and pH. Thermodynamic properties including Gibbs free energy, enthalpy, and entropy, were evaluated by applying the Van't Hoff equation. In addition, the adsorption energy distribution functions which describe heterogeneous characteristics of porous solid sorbents were calculated by using the generalized nonlinear regularization method. Adsorption kinetic studies were carried out in batch adsorber under important conditions such as PAC types, temperature, pH, and concentration. We found that fast and efficient removal of TNT dissolved in water can be successfully achieved by PAC adsorption.

  4. Effect of Molar Concentration of NH4OH on Photocatalytic Activity in Preparation of Nanosized TiO2 Powder from Spent Titanium Chip by Sol-Gel Method.

    PubMed

    Lee, Hwan-Gyu; Lee, Young-Ho; Yun, Hyeon-Jun; Jo, Jang-Ho; Kim, Seong-Kyung; Yu, Hyeon-Jin; Kim, Ki-Joong; Kang, Byeong-Mo; Jeong, Woon-Jo; Chung, Min-Chul; Jung, Sang-Chul; Lee, Do-Jin; Ahn, Ho-Geun

    2016-05-01

    The TiO2 powder was prepared from the spent titanium chips by applying the sol-gel method. The spent titanium chip was dissolved in HCl solution, and then NH4OH solution was added. The molar concentration of NH4OH solution was 2 M, 4 M, 8 M, and 10 M. Obtained TiO2 powders were calcined at 200 degrees C, 400 degrees C, and 600 degrees C. The prepared TiO2 powder was characterized using a particle size analysis, BET surface area, and XRD analysis. The crystal structure of the TiO2 powder was rutile type and anatase. The highest BET surface area of TiO2 powder was 432.8 m2/g. The photocatalytic property of the TiO2 powder was evaluated as decomposition rate of methylene blue(MB) by using a liquid phase stirred reactor. UV source was a UV-A, and concentration of MB in most experiments was 8 ppm. The concentration of MB was measured by absorbance at 664 nm using UV spectroscopy. Photocatalytic efficiency of prepared TiO2 powder depended highly on concentration of NH4OH solution. The TiO2 powder prepared with 8 M-NH4OH solution showed the highest efficiency, the decomposition efficiency at decomposition time of 2 hr and MB concentration of pH 8 was 98%. PMID:27483804

  5. Removal of disinfection by-products in raw water using a biological powder-activated carbon system.

    PubMed

    Lou, Jie C; Tseng, Wei B; Wu, Ming C; Han, Jia Y; Chen, Bi H

    2012-01-01

    This study investigates the removal efficiency of disinfection by-products (DBPs) in raw water at a water treatment plant using a biological powder-activated carbon system (BPACS). The presence of an excessive amount of DBPs has a large impact on the water quality of drinking water treated from the purification process. This study collected rapidly filtered water from an advanced water treatment plant for use in experiments on raw water. The removal efficiency of the trihalomethane formation potential (THMFP) and haloacetic acids formation potential (HAAFP) was studied under various hydraulic retention times and under organic DOC loadings. The results showed that the BPACS lowered the average concentration of dissolved organic carbon (DOC), UV(254) and the SUVA value (equivalent to UV(254)/DOC) in raw water. The system efficiently removed the THMFP and HAAFP during the treatment of the three primary organic carbon items. These results highlight the importance of the BPACS for efficiently treating disinfection by-products. These discoveries provide important information on biological degradation behaviors that can remove excessive amounts of disinfection by-products from drinking water.

  6. Degradation of a model azo dye in submerged anaerobic membrane bioreactor (SAMBR) operated with powdered activated carbon (PAC).

    PubMed

    Baêta, B E L; Luna, H J; Sanson, A L; Silva, S Q; Aquino, S F

    2013-10-15

    This work investigated the anaerobic degradation of the model azo dye Remazol Yellow Gold RNL in an upflow anaerobic sludge blanket reactor (UASB) and two submerged anaerobic membrane (SAMBR) bioreactors, one of which (SAMBR-1) was operated with powdered activated carbon (PAC) in its interior. The reactors were operated at 35 °C with a hydraulic retention time of 24 h in three operational phases, aimed to assess the effect of external sources of carbon (glucose) or redox mediator (yeast extract) on the removal or color and organic matter. The results showed that removal efficiencies of COD (73-94%) and color (90-94%) were higher for SAMBR-1 when compared to SAMBR-2 (operated without PAC) and UASB reactors. In addition, the presence of PAC in SAMBR-1 increased reactor stability, thereby leading to a lower accumulation of volatile fatty acids (VFA). The microfiltration membrane was responsible for an additional removal of ~50% of soluble residual COD in the form of VFA, thus improving permeate quality. On its turn, PAC exhibited the ability to adsorb byproducts (aromatic amines) of azo dye degradation as well as to act as source of immobilized redox mediator (quinone groups on its surface), thereby enhancing color removal. PMID:23810998

  7. Application of powdered activated carbon for the adsorption of cylindrospermopsin and microcystin toxins from drinking water supplies.

    PubMed

    Ho, Lionel; Lambling, Paul; Bustamante, Heriberto; Duker, Phil; Newcombe, Gayle

    2011-04-01

    Cylindrospermopsin (CYN) and microcystin are two potent toxins that can be produced by cyanobacteria in drinking water supplies. This study investigated the application of powdered activated carbon (PAC) for the removal of these toxins under conditions that could be experienced in a water treatment plant. Two different PACs were evaluated for their ability to remove CYN and four microcystin variants from various drinking water supplies. The removal of natural organic material by the PACs was also determined by measuring the levels of dissolved organic carbon and UV absorbance (at 254 nm). The PACs effectively removed CYN and the microcystins from each of the waters studied, with one of the PACs shown to be more effective, possibly due to its smaller particle diameter. No difference in removal of the toxins was observed using PAC contact times of 30, 45 and 60 min. Furthermore, the effect of water quality on the removal of the toxins was minimal. The microcystin variants were adsorbed in the order: MCRR > MCYR > MCLR > MCLA. CYN was found to be adsorbed similarly to MCRR. PMID:21459402

  8. Impacts of ozonation on the competition between organic micro-pollutants and effluent organic matter in powdered activated carbon adsorption.

    PubMed

    Zietzschmann, F; Mitchell, R-L; Jekel, M

    2015-11-01

    This study investigates if ozonation of wastewater treatment plant (WWTP) effluent can reduce the negative impacts of effluent organic matter (EfOM) on the adsorption of organic micro-pollutants (OMP) onto powdered activated carbon (PAC). Pre-treatment of the water included membrane filtration for the removal of suspended/colloidal organics, ozonation with various specific ozone consumptions, and subsequent OMP spiking to comparable initial concentrations in all of the ozonated waters. This approach allowed for comparative PAC adsorption tests. Adsorption analyses show that the adsorbability of EfOM decreases with increasing specific ozone consumptions. This is also reflected by liquid chromatography with online carbon and UV254 detection (LC-OCD) which shows the ozone-induced disintegration of large EfOM into smaller fragments. Also, small organic neutrals are decreased while the small organic acids peak continuously increases with rising specific ozone consumptions. UV254 demonstrates that the aromaticity of all LC-OCD fractions continuously declines together with increasing specific O3 consumptions. This explains the varying EfOM adsorbabilities that occur due to ozonation. The ozone-induced decrease of EfOM adsorbability directly translates into reduced adsorption competition against the adsorption of OMP. With higher specific ozone consumptions, OMP removal and OMP loadings increase. The reduced adsorption competition is reflected in the outputs from equivalent background compound (EBC) modeling. In each of the ozonated waters, correlations between the OMP removals and the UV254 removal were found.

  9. Adsorption of ciprofloxacin, bisphenol and 2-chlorophenol on electrospun carbon nanofibers: in comparison with powder activated carbon.

    PubMed

    Li, Xiaona; Chen, Shuo; Fan, Xinfei; Quan, Xie; Tan, Feng; Zhang, Yaobin; Gao, Jinsuo

    2015-06-01

    Carbon nanofibers (CNFs) were prepared by electrospun polyacrylonitrile (PAN) polymer solutions followed by thermal treatment. For the first time, the influence of stabilization procedure on the structure properties of CNFs was explored to improve the adsorption capacity of CNFs towards the environmental pollutants from aqueous solution. The adsorption of three organic chemicals including ciprofloxacin (CIP), bisphenol (BPA) and 2-chlorophenol (2-CP) on electrospun CNFs with high surface area of 2326m(2)/g and micro/mesoporous structure characteristics were investigated. The adsorption affinities were compared with that of the commercial powder activated carbon (PAC). The adsorption kinetics and isotherms showed that the maximum adsorption capacities (qm) of CNFs towards the three pollutants are sequenced in the order of CIP>BPA>2-CP, which are 2.6-fold (CIP), 1.6-fold (BPA) and 1.1-fold (2-CP) increase respectively in comparison with that of PAC adsorption. It was assumed that the micro/mesoporous structure of CNFs, molecular size of the pollutants and the π electron interaction play important roles on the high adsorption capacity exhibited by CNFs. In addition, electrostatic interaction and hydrophobic interaction also contribute to the adsorption of CNFs. This study demonstrates that the electrospun CNFs are promising adsorbents for the removal of pollutants from aqueous solutions.

  10. Impacts of ozonation on the competition between organic micro-pollutants and effluent organic matter in powdered activated carbon adsorption.

    PubMed

    Zietzschmann, F; Mitchell, R-L; Jekel, M

    2015-11-01

    This study investigates if ozonation of wastewater treatment plant (WWTP) effluent can reduce the negative impacts of effluent organic matter (EfOM) on the adsorption of organic micro-pollutants (OMP) onto powdered activated carbon (PAC). Pre-treatment of the water included membrane filtration for the removal of suspended/colloidal organics, ozonation with various specific ozone consumptions, and subsequent OMP spiking to comparable initial concentrations in all of the ozonated waters. This approach allowed for comparative PAC adsorption tests. Adsorption analyses show that the adsorbability of EfOM decreases with increasing specific ozone consumptions. This is also reflected by liquid chromatography with online carbon and UV254 detection (LC-OCD) which shows the ozone-induced disintegration of large EfOM into smaller fragments. Also, small organic neutrals are decreased while the small organic acids peak continuously increases with rising specific ozone consumptions. UV254 demonstrates that the aromaticity of all LC-OCD fractions continuously declines together with increasing specific O3 consumptions. This explains the varying EfOM adsorbabilities that occur due to ozonation. The ozone-induced decrease of EfOM adsorbability directly translates into reduced adsorption competition against the adsorption of OMP. With higher specific ozone consumptions, OMP removal and OMP loadings increase. The reduced adsorption competition is reflected in the outputs from equivalent background compound (EBC) modeling. In each of the ozonated waters, correlations between the OMP removals and the UV254 removal were found. PMID:26231581

  11. Use of submerged anaerobic membrane bioreactor (SAMBR) containing powdered activated carbon (PAC) for the treatment of textile effluents.

    PubMed

    Baêta, B E L; Ramos, R L; Lima, D R S; Aquino, S F

    2012-01-01

    This work investigated the use of submerged anaerobic membrane bioreactors (SAMBRs) in the presence and absence of powdered activated carbon (PAC) for the treatment of genuine textile wastewater. The reactors were operated at 35 °C with an HRT of 24 h and the textile effluent was diluted (1:10) with nutrient solution containing yeast extract as the source of the redox mediation riboflavin. The results showed that although both SAMBRs exhibited an excellent performance, the presence of PAC inside SAMBR-1 enhanced reactor stability and removal efficiency of chemical oxygen demand (COD), volatile fatty acids (VFA), turbidity and color. The median removal efficiencies of COD and color in SAMBR-1 were, 90 and 94% respectively; whereas for SAMBR-2 (without PAC) these values were 79 and 86%, In addition, the median values of turbidity and VFA were 8 NTU and 8 mg/L for SAMBR-1 and 14 NTU and 26 mg/L for SAMBR-2, indicating that the presence of PAC inside SAMBR-1 led to the production of an anaerobic effluent of high quality regarding such parameters. PMID:22508114

  12. Use of submerged anaerobic membrane bioreactor (SAMBR) containing powdered activated carbon (PAC) for the treatment of textile effluents.

    PubMed

    Baêta, B E L; Ramos, R L; Lima, D R S; Aquino, S F

    2012-01-01

    This work investigated the use of submerged anaerobic membrane bioreactors (SAMBRs) in the presence and absence of powdered activated carbon (PAC) for the treatment of genuine textile wastewater. The reactors were operated at 35 °C with an HRT of 24 h and the textile effluent was diluted (1:10) with nutrient solution containing yeast extract as the source of the redox mediation riboflavin. The results showed that although both SAMBRs exhibited an excellent performance, the presence of PAC inside SAMBR-1 enhanced reactor stability and removal efficiency of chemical oxygen demand (COD), volatile fatty acids (VFA), turbidity and color. The median removal efficiencies of COD and color in SAMBR-1 were, 90 and 94% respectively; whereas for SAMBR-2 (without PAC) these values were 79 and 86%, In addition, the median values of turbidity and VFA were 8 NTU and 8 mg/L for SAMBR-1 and 14 NTU and 26 mg/L for SAMBR-2, indicating that the presence of PAC inside SAMBR-1 led to the production of an anaerobic effluent of high quality regarding such parameters.

  13. A coagulation-powdered activated carbon-ultrafiltration--multiple barrier approach for removing toxins from two Australian cyanobacterial blooms.

    PubMed

    Dixon, Mike B; Richard, Yann; Ho, Lionel; Chow, Christopher W K; O'Neill, Brian K; Newcombe, Gayle

    2011-02-28

    Cyanobacteria are a major problem for the world wide water industry as they can produce metabolites toxic to humans in addition to taste and odour compounds that make drinking water aesthetically displeasing. Removal of cyanobacterial toxins from drinking water is important to avoid serious illness in consumers. This objective can be confidently achieved through the application of the multiple barrier approach to drinking water quality and safety. In this study the use of a multiple barrier approach incorporating coagulation, powdered activated carbon (PAC) and ultrafiltration (UF) was investigated for the removal of intracellular and extracellular cyanobacterial toxins from two naturally occurring blooms in South Australia. Also investigated was the impact of these treatments on the UF flux. In this multibarrier approach, coagulation was used to remove the cells and thus the intracellular toxin while PAC was used for extracellular toxin adsorption and finally the UF was used for floc, PAC and cell removal. Cyanobacterial cells were completely removed using the UF membrane alone and when used in conjunction with coagulation. Extracellular toxins were removed to varying degrees by PAC addition. UF flux deteriorated dramatically during a trial with a very high cell concentration; however, the flux was improved by coagulation and PAC addition. PMID:21227576

  14. Solar regeneration of powdered activated carbon impregnated with visible-light responsive photocatalyst: factors affecting performances and predictive model.

    PubMed

    Yap, Pow-Seng; Lim, Teik-Thye

    2012-06-01

    This study demonstrated a green technique to regenerate spent powdered activated carbon (AC) using solar photocatalysis. The AC was impregnated with a photocatalyst photoexcitable under visible-light irradiation to yield a solar regenerable composite, namely nitrogen-doped titanium dioxide (N-TiO(2)/AC). This composite exhibited bifunctional adsorptive-photocatalytic characteristics. Contaminants of emerging environmental concern, i.e. bisphenol-A (BPA), sulfamethazine (SMZ) and clofibric acid (CFA) which exhibited varying affinities for AC were chosen as target pollutants. The adsorption of BPA and SMZ by the N-TiO(2)/AC was significantly higher than that of CFA. The performance of solar photocatalytic regeneration (SPR) of the spent N-TiO(2)/AC composite generally increased with light intensity, N-TiO(2) loading and temperature. The regeneration efficiency (RE) for CFA-loaded spent composite was the highest compared to the other pollutant-loaded spent composites, achieving 77% within 8h of solar irradiation (765 W m(-2)). The rate-limiting process was pollutant desorption from the interior AC sorption sites. A kinetic model was developed to predict the transient concentration of the sorbate remaining in the spent composite during SPR. Comparison studies using solvent extraction technique indicated a different order of RE for the three pollutants, attributable to their varying solubilities in the aqueous and organic solvents. PMID:22464146

  15. Modeling nonequilibrium adsorption of MIB and sulfamethoxazole by powdered activated carbon and the role of dissolved organic matter competition.

    PubMed

    Shimabuku, Kyle K; Cho, Hyukjin; Townsend, Eli B; Rosario-Ortiz, Fernando L; Summers, R Scott

    2014-12-01

    This study demonstrates that the ideal adsorbed solution theory-equivalent background compound (IAST-EBC) as a stand-alone model can simulate and predict the powdered activated carbon (PAC) adsorption of organic micropollutants found in drinking water sources in the presence of background dissolved organic matter (DOM) under nonequilibrium conditions. The IAST-EBC represents the DOM competitive effect as an equivalent background compound (EBC). When adsorbing 2-methylisoborneol (MIB) with PAC, the EBC initial concentration was a similar percentage, on average 0.51%, of the dissolved organic carbon in eight nonwastewater impacted surface waters. Using this average percentage in the IAST-EBC model yielded good predictions for MIB removal in two nonwastewater impacted waters. The percentage of competitive DOM was significantly greater in wastewater impacted surface waters, and varied markedly in DOM size fractions. Fluorescence parameters exhibited a strong correlation with the percentage of competitive DOM in these waters. Utilizing such correlations in the IAST-EBC successfully modeled MIB and sulfamethoxazole adsorption by three different PACs in the presence of DOM that varied in competitive effect. The influence of simultaneous coagulant addition on PAC adsorption of micropollutants was also investigated. Coagulation caused the DOM competitive effect to increase and decrease with MIB and sulfamethoxazole, respectively. PMID:25371136

  16. Comparing and modeling organic micro-pollutant adsorption onto powdered activated carbon in different drinking waters and WWTP effluents.

    PubMed

    Zietzschmann, Frederik; Aschermann, Geert; Jekel, Martin

    2016-10-01

    The adsorption of organic micro-pollutants (OMP) onto powdered activated carbon (PAC) was compared between regionally different waters within two groups, namely five drinking waters and seven wastewater treatment plant (WWTP) effluents. In all waters, OMP were spiked to adjust similar ratios of the initial OMP and DOC concentrations (c0,OMP/c0,DOC). PAC was dosed specific to the respective DOC (e.g. 2 mg PAC/per mg DOC). Liquid chromatography with online carbon detection shows differences of the background organic matter (BOM) compositions. The OMP removals at given DOC-specific PAC doses vary by ±15% (drinking waters) and ±10% (WWTP effluents). Similar BOM-induced adsorption competition in the waters of the respective group results in overall relationships between the PAC loadings and the liquid phase concentrations of each OMP (in the case of strong adsorbates). Weaker adsorbates show no overall relationships because of the strong BOM-induced adsorption competition near the initial OMP concentration. Correlations between OMP removals and UV254 removals were independent of the water (within the respective group). The equivalent background compound (EBC) model was applied to the experimental data. Using global EBC Freundlich coefficients, the initial EBC concentration correlates with the DOC (both water groups separately) and the low molecular weight (LMW) organics concentrations (all waters combined). With these correlations, the EBC could be initialized by using the DOC or the LMW organics concentration of additional drinking water, WWTP effluent, and surface water samples. PMID:27344250

  17. Improving the performance of an aerobic membrane bioreactor (MBR) treating pharmaceutical wastewater with powdered activated carbon (PAC) addition.

    PubMed

    Kaya, Yasemin; Bacaksiz, A Murat; Golebatmaz, Ugur; Vergili, Ilda; Gönder, Z Beril; Yilmaz, Gulsum

    2016-04-01

    In this study, the effects of organic loading rate (OLR) and the addition of powdered activated carbon (PAC) on the performance and membrane fouling of MBR were conducted to treat real pharmaceutical process wastewater. Over 145 days of operation, the MBR system was operated at OLRs ranging from 1 to 2 kg COD m(-3) day(-1) without sludge wasting. The addition of PAC provided an improvement in the flux, despite an increase in the OLR:PAC ratio. The results demonstrated that the hybrid PAC-MBR system maintained a reduced amount of membrane fouling and steadily increased the removal performance of etodolac. PAC addition reduced the deposition of extracellular polymeric substance and organic matter on the membrane surface and resulted an increase in COD removal even at higher OLRs with low PAC addition. Membrane fouling mechanisms were investigated using combined adsorption fouling models. Modified fouling index values and normalized mass transfer coefficient values indicated that predominant fouling mechanism was cake adsorption. PMID:26846538

  18. Prediction of powdered activated carbon doses for 2-MIB removal in drinking water treatment using a simplified HSDM approach.

    PubMed

    Yu, Jianwei; Yang, Fong-Chen; Hung, Wei-Nung; Liu, Chia-Ling; Yang, Min; Lin, Tsair-Fuh

    2016-08-01

    The addition of powdered activated carbon (PAC) is an effective measure to cope with seasonal taste and odor (T&O) problems caused by 2-methylisoborneol (2-MIB) and trans-1, 10-dimethyl-trans-9-decalol (geosmin) in drinking water. Some T&O problems are episodic in nature, and generally require rapid responses. This paper proposed a simplified approach for the application of the homogenous surface diffusion model (HSDM) to predict the appropriate PAC doses for the removal of 2-MIB. Equilibrium and kinetic experiments were performed for 2-MIB adsorption onto five PACs in three source waters. The simplified HSDM approach was compared with the experimental data, by assigning the Freundlich 1/n value in the range of 0.1-1.0 and obtaining the Freundlich equilibrium parameter K value through a 6-hr adsorption kinetic test. The model describes the kinetic adsorption data very well for all of the tested PACs in different source waters. The results were validated using the data obtained from one full scale water treatment plant, and the differences between the predicted and observed results were within 10% range. This simplified HSDM approach may be applied for the rapid determination of PAC doses for water treatment plants when faced with 2-MIB episodes in source waters. PMID:27186686

  19. The application of powdered activated carbon for MIB and geosmin removal: predicting PAC doses in four raw waters.

    PubMed

    Cook, D; Newcombe, G; Sztajnbok, P

    2001-04-01

    Blooms of blue-green algae in reservoirs often produce the musty-earthy taste and odour algal metabolites 2-methylisoborneol (MIB) and geosmin. MIB and geosmin are not removed by conventional water treatment and their presence in the distribution system, even at low ng L-1 levels, can result in consumer complaints. Powdered activated carbon (PAC) can effectively remove MIB and geosmin when the correct dose is applied. The homogeneous surface diffusion model (HSDM) was used to predict PAC doses required to reduce MIB and geosmin concentrations to below 10 ng L-1 at four water treatment plants in Adelaide, South Australia. In jar tests, undertaken under treatment plant conditions, the predicted doses were found to produce water of the desired quality in three of the four waters. The poor predictions found in the fourth water, which had a considerably higher turbidity, were attributed to the incorporation of PAC in a larger, denser floc, leading to a reduced effective contact time of the adsorbent. It was found that higher doses of PAC were required for both compounds to produce acceptable quality water when turbidities rose above 26 NTU.

  20. PAH-sequestration capacity of granular and powder activated carbon amendments in soil, and their effects on earthworms and plants.

    PubMed

    Jakob, Lena; Hartnik, Thomas; Henriksen, Thomas; Elmquist, Marie; Brändli, Rahel C; Hale, Sarah E; Cornelissen, Gerard

    2012-07-01

    A field lysimeter study was carried out to investigate whether the amendment of 2% powder and granular activated carbon (PAC and GAC) to a soil with moderate PAH contamination had an impact on the PAH bioaccumulation of earthworms and plants, since AC is known to be a strong sorbent for organic pollutants. Furthermore, secondary effects of AC on plants and earthworms were studied through growth and nutrient uptake, and survival and weight gain. Additionally, the effect of AC amendments on soil characteristics like pH, water holding capacity, and the water retention curve of the soil were investigated. Results show that the amendment of 2% PAC had a negative effect on plant growth while the GAC increased the growth rate of plants. PAC was toxic to earthworms, demonstrated by a significant weight loss, while the results for GAC were less clear due to ambiguous results of a field and a parallel laboratory study. Both kinds of AC significantly reduced biota to soil accumulation factors (BSAFs) of PAHs in earthworms and plants. The GAC reduced the BSAFs of earthworms by an average of 47 ± 44% and the PAC amendment reduced them by 72 ± 19%. For the investigated plants the BSAFs were reduced by 46 ± 36% and 53 ± 22% by the GAC and PAC, respectively.

  1. Prediction of powdered activated carbon doses for 2-MIB removal in drinking water treatment using a simplified HSDM approach.

    PubMed

    Yu, Jianwei; Yang, Fong-Chen; Hung, Wei-Nung; Liu, Chia-Ling; Yang, Min; Lin, Tsair-Fuh

    2016-08-01

    The addition of powdered activated carbon (PAC) is an effective measure to cope with seasonal taste and odor (T&O) problems caused by 2-methylisoborneol (2-MIB) and trans-1, 10-dimethyl-trans-9-decalol (geosmin) in drinking water. Some T&O problems are episodic in nature, and generally require rapid responses. This paper proposed a simplified approach for the application of the homogenous surface diffusion model (HSDM) to predict the appropriate PAC doses for the removal of 2-MIB. Equilibrium and kinetic experiments were performed for 2-MIB adsorption onto five PACs in three source waters. The simplified HSDM approach was compared with the experimental data, by assigning the Freundlich 1/n value in the range of 0.1-1.0 and obtaining the Freundlich equilibrium parameter K value through a 6-hr adsorption kinetic test. The model describes the kinetic adsorption data very well for all of the tested PACs in different source waters. The results were validated using the data obtained from one full scale water treatment plant, and the differences between the predicted and observed results were within 10% range. This simplified HSDM approach may be applied for the rapid determination of PAC doses for water treatment plants when faced with 2-MIB episodes in source waters.

  2. Evaluation of the biocompatibility and osteoproductive activity of ostrich eggshell powder in experimentally induced calvarial defects in rabbits.

    PubMed

    Durmuş, Ercan; Celik, Ilhami; Aydin, M Faruk; Yildirim, Gülsün; Sur, Emrah

    2008-07-01

    The purpose of this study was to investigate the beneficial effects of particulate ostrich eggshell grafting on the healing of experimentally induced skull defects. The clinical, radiological, histological, and histomorphometrical findings of this material were compared with the results of commercially available demineralized bone matrix (DBM). The study was conducted on 18 adult New Zealand rabbits. One defect served as a control and the remaining ones either were filled with different sized eggshell particles or DBM, in each animal. Clinical and radiological inspections and histologic investigations of the animals were done at the 1st, 3rd, and 6th months of postoperative period. Radiologically, minimal bone regeneration was observed at the empty, control defect sites. The most advanced bone regeneration was in the DBM grafted defects. The eggshell particle grafted defect sites displayed weak bone regeneration at earlier stages, at 1st and 3rd months after operation when compared with demineralized bone matrix. Nevertheless, ossification was satisfactory at 6th month after operation when compared with the control defects. Within the limitations of this study, it was concluded that Ostrich eggshell powder (OSP) is a worth-while bone substitute because it is a safe, cheap, and easily available material. Long-term studies will clarify its possible role in maxillofacial surgery. Further sophisticated experiments should be undertaken before human implantation concerning its osteoproductive activity alone or in combination with other materials. PMID:18076098

  3. Removal of Trace Pharmaceuticals from Water using coagulation and powdered activated carbon as pretreatment to ultrafiltration membrane system.

    PubMed

    Sheng, Chenguang; Nnanna, A G Agwu; Liu, Yanghe; Vargo, John D

    2016-04-15

    In this study, the efficacy of water treatment technologies: ultra-filtration (UF), powdered activated carbon (PAC), coagulation (COA) and a combination of these technologies (PAC/UF and COA/UF) to remove target pharmaceuticals (Acetaminophen, Bezafibrate, Caffeine, Carbamazepine, Cotinine, Diclofenac, Gemfibrozil, Ibuprofen, Metoprolol, Naproxen, Sulfadimethoxine, Sulfamethazine, Sulfamethoxazole, Sulfathiazole, Triclosan and Trimethoprim) was investigated. Samples of wastewater from municipal WWTPs were analyzed using direct aqueous injection High Performance Liquid Chromatography with Tandem Quadrupole Mass Spectrometric (LC/MS/MS) detection. On concentration basis, results showed an average removal efficiency of 29%, 50%, and 7%, respectively, for the UF, PAC dosage of 50ppm, and COA dosage of 10ppm. When PAC dosage of 100ppm was used as pretreatment to the combined PAC and UF in-line membrane system, a 90.3% removal efficiency was achieved. The removal efficiency of UF in tandem with COA was 33%, an increase of 4% compared with the single UF treatment. The adsorption effect of PAC combined with the physical separation process of UF revealed the best treatment strategy for removing pharmaceutical contaminant from water. PMID:26867086

  4. Degradation of a model azo dye in submerged anaerobic membrane bioreactor (SAMBR) operated with powdered activated carbon (PAC).

    PubMed

    Baêta, B E L; Luna, H J; Sanson, A L; Silva, S Q; Aquino, S F

    2013-10-15

    This work investigated the anaerobic degradation of the model azo dye Remazol Yellow Gold RNL in an upflow anaerobic sludge blanket reactor (UASB) and two submerged anaerobic membrane (SAMBR) bioreactors, one of which (SAMBR-1) was operated with powdered activated carbon (PAC) in its interior. The reactors were operated at 35 °C with a hydraulic retention time of 24 h in three operational phases, aimed to assess the effect of external sources of carbon (glucose) or redox mediator (yeast extract) on the removal or color and organic matter. The results showed that removal efficiencies of COD (73-94%) and color (90-94%) were higher for SAMBR-1 when compared to SAMBR-2 (operated without PAC) and UASB reactors. In addition, the presence of PAC in SAMBR-1 increased reactor stability, thereby leading to a lower accumulation of volatile fatty acids (VFA). The microfiltration membrane was responsible for an additional removal of ~50% of soluble residual COD in the form of VFA, thus improving permeate quality. On its turn, PAC exhibited the ability to adsorb byproducts (aromatic amines) of azo dye degradation as well as to act as source of immobilized redox mediator (quinone groups on its surface), thereby enhancing color removal.

  5. Preparation and Characterization of Activated Cow Bone Powder for the Adsorption of Cadmium from Palm Oil Mill Effluent

    NASA Astrophysics Data System (ADS)

    AbdulRahman, A.; Latiff, A. A. A.; Daud, Z.; Ridzuan, M. B.; D, N. F. M.; Jagaba, A. H.

    2016-07-01

    Several studies have been conducted on the removal of heavy metals from palm oil mill effluent. In this study, cow bones were developed as an adsorbent for the removal of cadmium II from POME. A batch experiment was conducted to investigate the effectiveness of the prepared activated cow bone powder for the sorption of cadmium II from raw POME. The experiment was carried out under fixed conditions using 100mg/L raw POME combined with different adsorbent dosage of CBP of 184.471 Ra(nm) surface roughness. The equilibrium adsorption capacity of the hydrophobic CBP of average contact angle 890 was determined from the relationship between the initial and equilibrium liquid phase concentrations of POME. The optimum adsorption of cadmium II on CBP was at 10g adsorbent dosage for sample 1 and 2 at 97.8% and 96.93% respectively. The least uptake was at 30g adsorbent weight for both samples at average of 95.1% for both samples. The effective removal of cadmium ion showed that CBP has a great potential for the treatment of heavy metal in POME.

  6. Effect of mechanical activation on thermal and electrical conductivity of sintered Cu, Cr, and Cu/Cr composite powders

    NASA Astrophysics Data System (ADS)

    Rogachev, A. S.; Kuskov, K. V.; Moskovskikh, D. O.; Usenko, A. A.; Orlov, A. O.; Shkodich, N. F.; Alymov, M. I.; Mukasyan, A. S.

    2016-06-01

    The results of measurement of electric resistivity and thermal conductivity of materials obtained by spark plasma sintering from powders of Cu, Cr, and their mixtures in the range of 300-600 K are presented. It is shown that the grinding of powders in planetary mills results in a reasonably substantial change in the electric and thermal properties of materials: to increasing electric resistivity and decreasing thermal conductivity and temperature coefficients of electric resistivity. The possible causes of these effects are considered.

  7. Magnetic recovery of modified activated carbon powder used for removal of endocrine disruptors present in water.

    PubMed

    Borghi, Chiara Caterina; Fabbri, Massimo

    2014-01-01

    This paper was aimed at studying sustainable solutions for the treatment of water polluted by octylphenols and nonylphenols that are xenoextrogen compounds affecting human health and dangerous for the aquatic environment. We studied the removal of 4-octylphenol and 4-n-nonylphenol with concentrations of the order of 5-10 mg/l on a laboratory scale. A mixing time of 10 min with 0.1 g/l of magnetic-activated carbons (MACs) was enough to obtain 95 +/- 5% adsorption of both 4-octylphenol and 4-n-nonylphenol. The adsorption of the surfactants IGEPAL CO-630 and TRITON X-100, which are precursors of branched 4-nonylphenol and the carcinogenic 4-tert-octylphenol, respectively, was also studied using the same technique. For concentrations between 2 and 10mg/l of these alkylphenols ethoxylated, after 10min mixing with 0.5 g/l of MACs, a 95 +/- 5% adsorption was obtained. A 97 +/- 1% removal of MACs was achieved after 10min of continuous-flow magnetic filtration (14.5 l/min). The filter used was made of SUS440C magnetic steel spheres. Srm-Co permanent magnets provided a uniform flux density field of about 500 mT. PMID:24645486

  8. Magnetic recovery of modified activated carbon powder used for removal of endocrine disruptors present in water.

    PubMed

    Borghi, Chiara Caterina; Fabbri, Massimo

    2014-01-01

    This paper was aimed at studying sustainable solutions for the treatment of water polluted by octylphenols and nonylphenols that are xenoextrogen compounds affecting human health and dangerous for the aquatic environment. We studied the removal of 4-octylphenol and 4-n-nonylphenol with concentrations of the order of 5-10 mg/l on a laboratory scale. A mixing time of 10 min with 0.1 g/l of magnetic-activated carbons (MACs) was enough to obtain 95 +/- 5% adsorption of both 4-octylphenol and 4-n-nonylphenol. The adsorption of the surfactants IGEPAL CO-630 and TRITON X-100, which are precursors of branched 4-nonylphenol and the carcinogenic 4-tert-octylphenol, respectively, was also studied using the same technique. For concentrations between 2 and 10mg/l of these alkylphenols ethoxylated, after 10min mixing with 0.5 g/l of MACs, a 95 +/- 5% adsorption was obtained. A 97 +/- 1% removal of MACs was achieved after 10min of continuous-flow magnetic filtration (14.5 l/min). The filter used was made of SUS440C magnetic steel spheres. Srm-Co permanent magnets provided a uniform flux density field of about 500 mT.

  9. The added value of a European Union tuberculosis reference laboratory network--analysis of the national reference laboratory activities.

    PubMed

    Drobniewski, F A; Nikolayevskyy, V; Hoffner, S; Pogoryelova, O; Manissero, D; Ozin, A J

    2008-03-18

    National reference laboratories (NRL) and other laboratories are the cornerstones of well-functioning tuberculosis programmes and surveillance activities. However, the scope and activity of NRL services for mycobacterial identification and drug susceptibility testing (DST) has not been examined in detail across the European Union (EU), nor has the added value of cooperation and networking at the European level been explored with regard to strengthening laboratory services. Therefore, the European Centre for Disease Prevention and Control (ECDC) has commissioned a survey to explore these issues and to identify areas of work that could bring added value by supporting networking activities of tuberculosis (TB) reference laboratories in the EU. Structured questionnaires were sent to TB reference laboratory experts in the EU and European Economic Area (EEA) countries, and in three additional countries selected on the basis of their networking activities with EU projects and other initiatives (Switzerland, Croatia and Israel). The compiled results describe the activities and structure of 32 NRLs (29 countries replied, a response rate of 91%). The analysis of the survey led to the following recommendations for strengthening TB laboratory services: (1) implementing of the published European standards for TB laboratory services with respect to infrastructure, national reference functions, biosafety, human resources, quality assurance, operational research (including evaluation of new medical diagnostics), accuracy and speed, appropriately trained staff; (2) ensuring that laboratories only perform activities for which they have demonstrated proficiency; (3) implement validated and standardised second-line drug susceptibility testing (DST), including drugs used to define extensively drug-resistant tuberculosis (XDR TB); (4) aiming to identify Mycobacterium tuberculosis complex (MTBC) and rifampicin (RIF) resistance in over 90% of cultures and cases from smear-positive sputum

  10. The effect of Morus alba leaves extract and powder on resistin levels and liver transaminase enzymes activities in diabetes.

    PubMed

    Salemi, Z; Barzin Tond, S; Fallah, S; Shojaii, A; Seifi, M

    2016-01-01

    The current study was designed to investigate the changes of the resistin, aspartate aminotransferase (AST), alanine aminotransferase (ALT) levels of diabetic rats after treatment with Morus alba leaves flavonoid extract (MLE) and Morus alba leaves powder (MLP). Thirty male wistar rats in five groups including control and diabetic groups were included. Diabetic groups consisted of diabetic control, sham and treated group with MLE and MLP. Type 2 diabetes was induced in rats by administration of streptozotocin (STZ) and - nicotinamide. The serum concentrations of resistin and insulin in the study groups were identified by ELISA. ALT and AST activities were assayed by spectrophotometer. For the first time, it was shown that the uptake of MLE and MLP by diabetic rats could significantly decrease the serum fasting blood sugar (FBS), resistin levels and enzymes activity of ALT and AST and increases the concentration of serum insulin significantly (P<0.05). in comparison with the sham group and diabetic control. The results showed that there was no significant difference between the anti-diabetic and inflammatory properties of MLE and MLP. In this study, the possible protective effect of MLE and MLP administration was evaluated against destructive effect of STZ on liver and pancreas function in diabetic rats. The results showed that these effects may play an important role in the regulating of adipokines secretion such as resistin and insulin secretion which are involved in the control of diabetes and obesity. MLE and MLP treatment could be useful agents in combination with other therapies in diabetes improvement. PMID:27262814

  11. Antioxidant and antimicrobial activity of Kitaibelia vitifolia extract as alternative to the added nitrite in fermented dry sausage.

    PubMed

    Kurćubić, Vladimir S; Mašković, Pavle Z; Vujić, Jelena M; Vranić, Danijela V; Vesković-Moračanin, Slavica M; Okanović, Đorđe G; Lilić, Slobodan V

    2014-08-01

    Fermented dry sausages (FDS) without nitrite added, fortified with bioactive phenol and flavonoid compounds originating from the ethanol extract of Kitaibelia vitifolia were food matrix for investigation of its antioxidant and antimicrobial potency. These activities were researched in order to improve the sausages' shelf-life, safety, and provide health benefits to consumers as well. The oxidative stability of the FDS, containing two different levels of natural preservative, was evaluated using five different contemporary methods for antioxidative activity. The activity was tested on the 20th day of the refrigerated storage. Minimum inhibitory concentrations of the sausage extract were determined against six microorganisms, using a micro dilution method. Determined optimal effective concentration of dissolved K. vitifolia extract (12.5 g/kg of meat dough) revealed strong antioxidant activity, and moderate antimicrobial activity against Escherichia coli (minimum inhibitory concentrations=15.625 μg/mL). The modified sausages had typical chemical-physical characteristics of FDS, controlled on 0, 13, 26 d of ripening and 20, 40 and 60 d of storage.

  12. Value Added?

    ERIC Educational Resources Information Center

    UCLA IDEA, 2012

    2012-01-01

    Value added measures (VAM) uses changes in student test scores to determine how much "value" an individual teacher has "added" to student growth during the school year. Some policymakers, school districts, and educational advocates have applauded VAM as a straightforward measure of teacher effectiveness: the better a teacher, the better students…

  13. Hydrophobic organic chemicals (HOCs) removal from biologically treated landfill leachate by powder-activated carbon (PAC), granular-activated carbon (GAC) and biomimetic fat cell (BFC).

    PubMed

    Liyan, Song; Youcai, Zhao; Weimin, Sun; Ziyang, Lou

    2009-04-30

    Biological pretreatment efficiently remove organic matter from landfill leachate, but further removal of refractory hydrophobic organic chemicals (HOCs) is hard even with advanced treatment. In this work, three-stage-aged refuse bioreactor (ARB) efficiently removed chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of fresh leachate produced in Shanghai laogang landfill, from 8603 to 451 mg L(-1) and 1368 to 30 mg L(-1), respectively. In downstream treatment, 3 g L(-1) powder-activated carbon (PAC), granular-activated carbon (GAC) and biomimetic fat cell (BFC) removed 89.2, 73.4 and 81.1% HOCs, but only 24.6, 19.1 and 8.9% COD, respectively. Through the specific HOCs accumulation characteristics of BFC, about 11.2% HOCs with low molecular weight (<1000 Da) in the biologically treated leachate were concluded. Since HOCs are competitively trapped by dissolved organic matters (DOM), the ultimate removal of HOCs from leachate is unreachable by activated carbon or BFC. It was also found that the biologically treated leachate effluent exhibited a wide molecular weight distribution (34-514,646 Da). These constitutes are derived from both autochthonous and allochthonous matters as well as biological activities.

  14. Impacts of coagulation on the adsorption of organic micropollutants onto powdered activated carbon in treated domestic wastewater.

    PubMed

    Altmann, Johannes; Zietzschmann, Frederik; Geiling, Eva-Linde; Ruhl, Aki Sebastian; Sperlich, Alexander; Jekel, Martin

    2015-04-01

    The application of powdered activated carbon (PAC) as an advanced wastewater treatment step for the removal of organic micropollutants (OMP) necessitates complete separation of the PAC particles, e.g. by coagulation. In this study, potential positive or negative indirect or direct effects of coagulation on the adsorption of OMPs onto PAC in treated wastewater were investigated. Although the concentration of dissolved organic matter (DOM) was significantly reduced by coagulation, the selective removal of mainly larger DOM components such as biopolymers and humic substances did not improve subsequent OMP adsorption onto PAC, demonstrating that coagulation has minor effects on DOM constituents that are relevant for direct competition or pore blocking. The combination of coagulation and adsorption yielded the sum of the individual removals, as adsorption predominantly affected smaller compounds. While the formation of flocs led to visible incorporation of PAC particles, no significant mass transfer limitations impeded the OMP adsorption. As a result, the dosing sequence of coagulant and PAC is not critical for efficient adsorption of OMPs onto PAC. The relationships between adsorptive OMP removal and corresponding reduction of UV absorption at 254 nm (UVA254) as a promising surrogate correlation for the real-time monitoring and PAC adjustment were affected by coagulation, leading to individual correlations depending on the water composition. Correcting for UVA254 reduction by coagulation produces adsorptive UVA254 removal, which correlates highly with OMP removal for different WWTP effluents and varying coagulant doses and can be applied in combined adsorption/coagulation processes to predict OMP removal and control PAC dosing.

  15. Elimination of micropollutants during post-treatment of hospital wastewater with powdered activated carbon, ozone, and UV.

    PubMed

    Kovalova, Lubomira; Siegrist, Hansruedi; von Gunten, Urs; Eugster, Jakob; Hagenbuch, Martina; Wittmer, Anita; Moser, Ruedi; McArdell, Christa S

    2013-07-16

    A pilot-scale hospital wastewater treatment plant consisting of a primary clarifier, membrane bioreactor, and five post-treatment technologies including ozone (O3), O3/H2O2, powdered activated carbon (PAC), and low pressure UV light with and without TiO2 was operated to test the elimination efficiencies for 56 micropollutants. The extent of the elimination of the selected micropollutants (pharmaceuticals, metabolites and industrial chemicals) was successfully correlated to physical-chemical properties or molecular structure. By mass loading, 95% of all measured micropollutants in the biologically treated hospital wastewater feeding the post-treatments consisted of iodinated contrast media (ICM). The elimination of ICM by the tested post-treatment technologies was 50-65% when using 1.08 g O3/gDOC, 23 mg/L PAC, or a UV dose of 2400 J/m(2) (254 nm). For the total load of analyzed pharmaceuticals and metabolites excluding ICM the elimination by ozonation, PAC, and UV at the same conditions was 90%, 86%, and 33%, respectively. Thus, the majority of analyzed substances can be efficiently eliminated by ozonation (which also provides disinfection) or PAC (which provides micropollutants removal, not only transformation). Some micropollutants recalcitrant to those two post-treatments, such as the ICM diatrizoate, can be substantially removed only by high doses of UV (96% at 7200 J/m(2)). The tested combined treatments (O3/H2O2 and UV/TiO2) did not improve the elimination compared to the single treatments (O3 and UV).

  16. Elimination of micropollutants during post-treatment of hospital wastewater with powdered activated carbon, ozone, and UV.

    PubMed

    Kovalova, Lubomira; Siegrist, Hansruedi; von Gunten, Urs; Eugster, Jakob; Hagenbuch, Martina; Wittmer, Anita; Moser, Ruedi; McArdell, Christa S

    2013-07-16

    A pilot-scale hospital wastewater treatment plant consisting of a primary clarifier, membrane bioreactor, and five post-treatment technologies including ozone (O3), O3/H2O2, powdered activated carbon (PAC), and low pressure UV light with and without TiO2 was operated to test the elimination efficiencies for 56 micropollutants. The extent of the elimination of the selected micropollutants (pharmaceuticals, metabolites and industrial chemicals) was successfully correlated to physical-chemical properties or molecular structure. By mass loading, 95% of all measured micropollutants in the biologically treated hospital wastewater feeding the post-treatments consisted of iodinated contrast media (ICM). The elimination of ICM by the tested post-treatment technologies was 50-65% when using 1.08 g O3/gDOC, 23 mg/L PAC, or a UV dose of 2400 J/m(2) (254 nm). For the total load of analyzed pharmaceuticals and metabolites excluding ICM the elimination by ozonation, PAC, and UV at the same conditions was 90%, 86%, and 33%, respectively. Thus, the majority of analyzed substances can be efficiently eliminated by ozonation (which also provides disinfection) or PAC (which provides micropollutants removal, not only transformation). Some micropollutants recalcitrant to those two post-treatments, such as the ICM diatrizoate, can be substantially removed only by high doses of UV (96% at 7200 J/m(2)). The tested combined treatments (O3/H2O2 and UV/TiO2) did not improve the elimination compared to the single treatments (O3 and UV). PMID:23758546

  17. Impacts of coagulation on the adsorption of organic micropollutants onto powdered activated carbon in treated domestic wastewater.

    PubMed

    Altmann, Johannes; Zietzschmann, Frederik; Geiling, Eva-Linde; Ruhl, Aki Sebastian; Sperlich, Alexander; Jekel, Martin

    2015-04-01

    The application of powdered activated carbon (PAC) as an advanced wastewater treatment step for the removal of organic micropollutants (OMP) necessitates complete separation of the PAC particles, e.g. by coagulation. In this study, potential positive or negative indirect or direct effects of coagulation on the adsorption of OMPs onto PAC in treated wastewater were investigated. Although the concentration of dissolved organic matter (DOM) was significantly reduced by coagulation, the selective removal of mainly larger DOM components such as biopolymers and humic substances did not improve subsequent OMP adsorption onto PAC, demonstrating that coagulation has minor effects on DOM constituents that are relevant for direct competition or pore blocking. The combination of coagulation and adsorption yielded the sum of the individual removals, as adsorption predominantly affected smaller compounds. While the formation of flocs led to visible incorporation of PAC particles, no significant mass transfer limitations impeded the OMP adsorption. As a result, the dosing sequence of coagulant and PAC is not critical for efficient adsorption of OMPs onto PAC. The relationships between adsorptive OMP removal and corresponding reduction of UV absorption at 254 nm (UVA254) as a promising surrogate correlation for the real-time monitoring and PAC adjustment were affected by coagulation, leading to individual correlations depending on the water composition. Correcting for UVA254 reduction by coagulation produces adsorptive UVA254 removal, which correlates highly with OMP removal for different WWTP effluents and varying coagulant doses and can be applied in combined adsorption/coagulation processes to predict OMP removal and control PAC dosing. PMID:25582393

  18. POWDERED ACTIVATED CARBON FROM NORTH DAKOTA LIGNITE: AN OPTION FOR DISINFECTION BY-PRODUCT CONTROL IN WATER TREATMENT PLANTS

    SciTech Connect

    Daniel J. Stepan; Thomas A. Moe; Melanie D. Hetland; Margaret L. Laumb

    2001-06-01

    New federal drinking water regulations have been promulgated to restrict the levels of disinfection by-products (DBPs) in finished public water supplies. DBPs are suspected carcinogens and are formed when organic material is partially oxidized by disinfectants commonly used in the water treatment industry. Additional federal mandates are expected in the near future that will further affect public water suppliers with respect to DBPs. Powdered activated carbon (PAC) has traditionally been used by the water treatment industry for the removal of compounds contributing to taste and odor problems. PAC also has the potential to remove naturally occurring organic matter (NOM) from raw waters prior to disinfection, thus controlling the formation of regulated DBPs. Many small water systems are currently using PAC for taste and odor control and have the potential to use PAC for controlling DBPs. This project, a cooperative effort between the Energy & Environmental Research Center (EERC), the Grand Forks Water Treatment Plant, and the University of North Dakota Department of Civil Engineering, consists of several interrelated tasks. The objective of the research was to evaluate a cost-effective PAC produced from North Dakota lignite for removing NOM from water and reducing trihalomethane formation potential. The research approach was to develop a statistically valid testing protocol that can be used to compare dose-response relationships between North Dakota lignite-derived PAC and commercially available PAC products. A statistical analysis was performed to determine whether significant correlations exist between operating conditions, water properties, PAC properties, and dose-response behavior. Pertinent physical and chemical properties were also measured for each of the waters and each of the PACs.

  19. The adsorptive capacity of vapor-phase mercury chloride onto powdered activated carbon derived from waste tires

    SciTech Connect

    Hsun-Yu Lin; Chung-Shin Yuan; Chun-Hsin Wu; Chung-Hsuang Hung

    2006-11-15

    Injection of powdered activated carbon (PAC) upstream of particulate removal devices (such as electrostatic precipitator and baghouses) has been used effectively to remove hazardous air pollutants, particularly mercury containing pollutants, emitted from combustors and incinerators. Compared with commercial PACs (CPACs), an alternative PAC derived from waste tires (WPAC) was prepared for this study. The equilibrium adsorptive capacity of mercury chloride (HgCl{sub 2}) vapor onto the WPAC was further evaluated with a self-designed bench-scale adsorption column system. The adsorption temperatures investigated in the adsorption column were controlled at 25 and 150{sup o}C. The superficial velocity and residence time of the flow were 0.01 m/sec and 4 sec, respectively. The adsorption column tests were run under nitrogen gas flow. Experimental results showed that WPAC with higher Brunauer Emmett Teller (BET) surface area could adsorb more HgCl{sub 2} at room temperature. The equilibrium adsorptive capacity of HgCl{sub 2} for WPAC measured in this study was 1.49 x 10{sup -1} mg HgCl{sub 2}/g PAC at 25{sup o}C with an initial HgCl{sub 2} concentration of 25 {mu}g/m{sup 3}. With the increase of adsorption temperature {le} 150{sup o}C, the equilibrium adsorptive capacity of HgCl{sub 2} for WPAC was decreased to 1.34 x 10{sup -1} mg HgCl{sub 2}/g PAC. Furthermore, WPAC with higher sulfur contents could adsorb even more HgCl{sub 2}. It was demonstrated that the mechanisms for adsorbing HgCl{sub 2} onto WPAC were physical adsorption and chemisorption at 25 and 150{sup o}C, respectively. 35 refs., 4 figs., 4 tabs.

  20. Effect of the adsorbate (Bromacil) equilibrium concentration in water on its adsorption on powdered activated carbon. Part 2: Kinetic parameters.

    PubMed

    Al Mardini, Fadi; Legube, Bernard

    2009-10-30

    The application of several monosolute equilibrium models has previously shown that Bromacil adsorption on SA-UF (Norit) powdered activated carbon (PAC) is probably effective on two types of sites. High reactivity sites were found to be 10-20 less present in a carbon surface than lower reactivity sites, according to the q(m) values calculated by isotherm models. The aims of this work were trying, primarily, to identify the kinetic-determinant stage of the sorption of Bromacil at a wide range of initial pesticide concentrations (approximately 5 to approximately 500 microg L(-1) at pH 7.8), and secondly, to specify the rate constants and other useful design parameters for the application in water treatment. It was therefore not possible to specify a priori whether the diffusion or surface reaction is the key step. It shows that many of the tested models which describe the stage of distribution or the surface reaction are correctly applied. However, the diffusivity values (D and D(0)) were found to be constant only constants for some specific experimental concentrations. The HSDM model of surface diffusion in pores was also applied but the values of the diffusion coefficient of surface (D(s)) were widely scattered and reduce significantly with the initial concentration or the equilibrium concentration in Bromacil. The model of surface reaction of pseudo-second order fitted particularly well and led to constant values which are independent of the equilibrium concentration, except for the low concentrations where the constants become significantly more important. This last observation confirms perfectly the hypothesis based on two types of sites as concluded by the equilibrium data (part 1).

  1. Do sedentary motives adversely affect physical activity? Adding cross-behavioural cognitions to the theory of planned behaviour.

    PubMed

    Rhodes, Ryan E; Blanchard, Chris M

    2008-01-01

    The purpose of this study was to explore whether sedentary behavior cognitions explain physical activity (PA) intention and behavior when integrated within the theory of planned behavior framework (TPB). A random community sample of 206 adults and a sample of 174 undergraduate students completed measures of the TPB pertaining to PA and four popular leisure-time behaviors (TV viewing, computer use, sedentary hobbies, and sedentary socializing) and an adapted Godin Leisure-Time Exercize Questionnaire (community sample = cross-sectional, undergraduate sample = 2-week prospective). Results using ordinary least squares regression provided evidence that TV viewing intention explains additional variance in PA behavior, and affective attitude (community sample) and perceived behavioral control (undergraduate sample) towards TV viewing explains additional variance in PA intention even after controlling for PA-related TPB constructs. These results underscore the potential value of adding sedentary control interventions in concert with PA promotion.

  2. Effect of adding ball-milled achenes to must on bioactive compounds and antioxidant activities in fruit wine.

    PubMed

    Lee, Pao-Ju; Chen, Shaun

    2016-03-01

    This study reports the utilization of ball-milled achenes in fermentation to increase the levels of ellagic acid and total phenol content, as well as to enhance the antioxidant capacity of strawberry wine. Achenes were micronized using ball-milling process, and then added to strawberry must prior to fermentation. The effects of the addition of ball-milled achenes on the ellagic acid and total phenol content in strawberry wine were determined, and the free radical scavenging and iron chelation activities were also analyzed. Quality attributes and acceptance were studied in comparison with a leading commercial strawberry wine for market application. The particle sizes of achenes were reduced from 1.1 mm to 400 nm after 30 min of ball-milling, and this led to an increase in the amount of extracted ellagic acid from 550.72 to 915.24 μg/g. The addition of ball-milled achenes to must led to a 19.72 % and 52.37 % increase in ellagic acid and total phenol content in strawberry wine, respectively. The increase in bioactive compounds resulted in increases of 54.09 %, 51.49 % and 56.97 % in ABTS and DPPH radical scavenging, and ferrous ion chelating activities, respectively. Although the commercial strawberry wine showed greater aroma intensity, no significant differences in overall quality and acceptance among the conventional process, added ball-milled achenes and the leading commercial strawberry wines were found. This study demonstrates that supplementation of ball-milled achenes in fermentation can be beneficial in increasing the levels of bioactive compounds and antioxidative capacity, indicating a good market potential. PMID:27570280

  3. How Effective Are Active Videogames Among the Young and the Old? Adding Meta-analyses to Two Recent Systematic Reviews

    PubMed Central

    Crutzen, Rik; Lu, Amy Shirong

    2014-01-01

    Abstract Objective: Two recent systematic reviews have surveyed the existing evidence for the effectiveness of active videogames in children/adolescents and in elderly people. In the present study, effect sizes were added to these systematic reviews, and meta-analyses were performed. Materials and Methods: All reviewed studies were considered for inclusion in the meta-analyses, but only studies were included that investigated the effectiveness of active videogames, used an experimental design, and used actual health outcomes as the outcome measures (body mass index for children/adolescents [k=5] and functional balance for the elderly [k=6]). Results: The average effect of active videogames in children and adolescents was small and nonsignificant: Hedges' g=0.20 (95 percent confidence interval, −0.08 to 0.48). Limited heterogeneity was observed, and no moderator analyses were performed. For the effect of active videogames on functional balance in the elderly, the analyses revealed a medium-sized and significant effect of g=0.68 (95 percent confidence interval, 0.13–1.24). For the elderly studies, substantial heterogeneity was observed. Moderator analyses showed that there were no significant effects of using a no-treatment control group versus an alternative treatment control group or of using games that were especially created for health-promotion purposes versus off-the-shelf games. Also, intervention duration and frequency, sample size, study quality, and dropout did not significantly moderate the effect of active videogames. Conclusions: The results of these meta-analyses provide preliminary evidence that active videogames can have positive effects on relevant outcome measures in children/adolescents and elderly individuals. PMID:26192486

  4. Guava (Psidium guajava L.) Powder as an Antioxidant Dietary Fibre in Sheep Meat Nuggets.

    PubMed

    Verma, Arun K; Rajkumar, V; Banerjee, Rituparna; Biswas, S; Das, Arun K

    2013-06-01

    This study was conducted to explore the antioxidant potential and functional value of guava (Psidium guajava L.) powder in muscle foods. Guava powder was used as a source of antioxidant dietary fibre in sheep meat nuggets at two different levels i.e., 0.5% (Treatment I) and 1.0% (Treatment II) and its effect was evaluated against control. Guava powder is rich in dietary fibre (43.21%), phenolics (44.04 mg GAE/g) and possesses good radical scavenging activity as well as reducing power. Incorporation of guava powder resulted in significant decrease (p<0.05) in pH of emulsion and nuggets, emulsion stability, cooking yield and moisture content of nuggets while ash and moisture content of emulsion were increased. Total phenolics, total dietary fibre (TDF) and ash content significantly increased (p<0.05) in nuggets with added guava powder. Product redness value was significantly improved (p<0.05) due to guava powder. Textural properties did not differ significantly except, springiness and shear force values. Guava powder was found to retard lipid peroxidation of cooked sheep meat nuggets as measured by TBARS number during refrigerated storage. Guava powder did not affect sensory characteristics of the products and can be used as source of antioxidant dietary fibre in meat foods.

  5. Energetic powder

    DOEpatents

    Jorgensen, Betty S.; Danen, Wayne C.

    2003-12-23

    Fluoroalkylsilane-coated metal particles. The particles have a central metal core, a buffer layer surrounding the core, and a fluoroalkylsilane layer attached to the buffer layer. The particles may be prepared by combining a chemically reactive fluoroalkylsilane compound with an oxide coated metal particle having a hydroxylated surface. The resulting fluoroalkylsilane layer that coats the particles provides them with excellent resistance to aging. The particles can be blended with oxidant particles to form energetic powder that releases chemical energy when the buffer layer is physically disrupted so that the reductant metal core can react with the oxidant.

  6. 21 CFR 169.182 - Vanilla-vanillin powder.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 2 2012-04-01 2012-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b)...

  7. 21 CFR 169.182 - Vanilla-vanillin powder.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b)...

  8. 21 CFR 169.182 - Vanilla-vanillin powder.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b)...

  9. 21 CFR 169.182 - Vanilla-vanillin powder.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b)...

  10. 21 CFR 169.182 - Vanilla-vanillin powder.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b)...

  11. Ceramic powder for sintering materials

    NASA Technical Reports Server (NTRS)

    Akiya, H.; Saito, A.

    1984-01-01

    Surface activity of ceramic powders such as MgO and Al2O3, for use in sintering with sp. emphasis on their particle size, shape, particle size distribution, packing, and coexisting additives and impurities are reviewed.

  12. Systems biology network-based discovery of a small molecule activator BL-AD008 targeting AMPK/ZIPK and inducing apoptosis in cervical cancer

    PubMed Central

    Tong, Xupeng; Zhang, Jin; Zhang, Yonghui; Ouyang, Liang; Liu, Bo; Huang, Jian

    2015-01-01

    The aim of this study was to discover a small molecule activator BL-AD008 targeting AMPK/ZIPK and inducing apoptosis in cervical cancer. In this study, we systematically constructed the global protein-protein interaction (PPI) network and predicted apoptosis-related protein connections by the Naïve Bayesian model. Then, we identified some classical apoptotic PPIs and other previously unrecognized PPIs between apoptotic kinases, such as AMPK and ZIPK. Subsequently, we screened a series of candidate compounds targeting AMPK/ZIPK, synthesized some compounds and eventually discovered a novel dual-target activator (BL-AD008). Moreover, we found BL-AD008 bear remarkable anti-proliferative activities toward cervical cancer cells and could induce apoptosis by death-receptor and mitochondrial pathways. Additionally, we found that BL-AD008-induced apoptosis was affected by the combination of AMPK and ZIPK. Then, we found that BL-AD008 bear its anti-tumor activities and induced apoptosis by targeting AMPK/ZIPK in vivo. In conclusion, these results demonstrate the ability of systems biology network to identify some key apoptotic kinase targets AMPK and ZIPK; thus providing a dual-target small molecule activator (BL-AD008) as a potential new apoptosis-modulating drug in future cervical cancer therapy. PMID:25797270

  13. Effect of calcination temperature on the photocatalytic activity of TiO2 powders prepared by co-precipitation of TiCl3

    NASA Astrophysics Data System (ADS)

    Yudoyono, Gatut; Ichzan, Nur; Zharvan, Vicran; Daniyati, Rizqa; Santoso, Hadi; Indarto, Bachtera; Pramono, Yono Hadi; Zainuri, Mochamad; Darminto

    2016-04-01

    The adsorption of basic dye methylene blue (MB) onto titanium dioxide (titania) powder that were prepared by coprecipitation method of TiCl3 and NH4OH as iniatial material with different calcination temperature was studied to examine the photocatalytic activity. Synthesis process carried out by the solution pH was adjusted to be 8. Effect of calcination temperature on the titania powder were characterized with Differential Scanning Calorimetry/Thermogravimetry (DSC/TG), X-ray diffraction (XRD), and Scanning Electron Microscopy (SEM). The result of TG and XRD showed that the NH4Cl decomposed between 235-372°C. The XRD result showed that the anatase TiO2 only contained a single phase when the calcination temperature of the precursor at 800°C, and over which it began to grow rutile phase. The influence of synthesis condition on the photocatalytic activity of TiO2 powder was determined by the photodegradation of MB dye under UV light.

  14. Enrichment of specific electro-active microorganisms and enhancement of methane production by adding granular activated carbon in anaerobic reactors.

    PubMed

    Lee, Jung-Yeol; Lee, Sang-Hoon; Park, Hee-Deung

    2016-04-01

    Direct interspecies electron transfer (DIET) via conductive materials can provide significant benefits to anaerobic methane formation in terms of production amount and rate. Although granular activated carbon (GAC) demonstrated its applicability in facilitating DIET in methanogenesis, DIET in continuous flow anaerobic reactors has not been verified. Here, evidences of DIET via GAC were explored. The reactor supplemented with GAC showed 1.8-fold higher methane production rate than that without GAC (35.7 versus 20.1±7.1mL-CH4/d). Around 34% of methane formation was attributed to the biomass attached to GAC. Pyrosequencing of 16S rRNA gene demonstrated the enrichment of exoelectrogens (e.g. Geobacter) and hydrogenotrophic methanogens (e.g. Methanospirillum and Methanolinea) from the biomass attached to GAC. Furthermore, anodic and cathodic currents generation was observed in an electrochemical cell containing GAC biomass. Taken together, GAC supplementation created an environment for enriching the microorganisms involved in DIET, which increased the methane production rate. PMID:26836607

  15. Effects of Annatto (Bixa orellana L.) Seeds Powder on Physicochemical Properties, Antioxidant and Antimicrobial Activities of Pork Patties during Refrigerated Storage

    PubMed Central

    Cuong, Tran Van; Chin, Koo Bok

    2016-01-01

    This study investigated the effect of the powder produced by ball-milling the outer layer of annatto (Bixa orellana L.) seeds on the physicochemical properties as well as the antioxidant and antimicrobial activities of pork patties over 14 d of refrigerated storage (4±1℃). Five pork patty treatments were produced containing three different concentrations of annatto seeds, 0.1, 0.25 and 0.5% (ANT0.1, ANT0.25, ANT0.5), 0.1% ascorbic acid (AA0.1), and a control (CTL). Based on the results, annatto seed powder appeared to show antioxidant activity. The Hunter color values of pork patties were affected by the addition of annatto seed powder, which increased the redness and yellowness values, but decreased the lightness of the patties (p<0.05). To evaluate the antioxidative effects of annatto on pork patties, thiobarbituric acid reactive substances (TBARS) and peroxide values (POV) were analyzed over 14 d of refrigerated storage. Treatments containing annatto seed showed lower TBARS and POV than control (CTL) samples (p<0.05). The volatile basic nitrogen (VBN) of the pork patties containing annatto seeds were lower than that of CTL at the end of storage (p<0.05). Although no differences in total bacterial counts were observed between control and treated patties, those containing annatto seeds had lower microbial counts for Enterobacteriacease than CTL or AA 0.1%. Therefore, annatto seed powder might be a good source of natural antioxidants for the production of meat products. PMID:27621688

  16. Enhanced magnetic properties of NiO powders by the mechanical activation of aluminothermic reduction of NiO prepared by a ball milling process

    NASA Astrophysics Data System (ADS)

    Padhan, Aneeta Manjari; Ravikumar, P.; Saravanan, P.; Alagarsamy, Perumal

    2016-11-01

    We report the effect of mechanical activation on NiO-Al (x wt%) reduction reaction and resulting structural and magnetic properties by carrying out high-energy planetary ball milling. The pure NiO (un-milled) and milled NiO-Al (x≤2.5) powders exhibit face centered cubic structure, but the antiferromagnetic nature of pure NiO powder shows significant room temperature ferromagnetism with moderate moment and coercivity after milling due to non-stoichiometry in NiO caused by the defects, size reduction and oxidation of Ni. On the other hand, the addition of Al between 2.5 and 10% in NiO forms solid solution of NiO-Al with considerable reduction in the moment due to the atomic disorder. With increasing Al above 10%, NiO reduction reaction progresses gradually and as a result, the average magnetization increases from 0.57 to 4.3 emu/g with increasing Al up to 25%. A maximum of 91% reduction was observed for NiO-Al (40%) powders in 30 h of milling with a large increase in magnetization (~24 emu/g) along with the development of α-Al2O3. Thermomagnetization data reveal the presence of mixed magnetic phases in milled NiO powders and the component of induced ferromagnetic phase fades out with increasing Al due to the formation of Ni from the NiO-Al reduction reaction. The changes in the structural and magnetic properties are discussed on the basis of mechanical activation on the reduction of NiO by Al. The controlled reduction reaction with different Al content in NiO-Al is encouraging for the applications in catalysis and process of ore reduction.

  17. Effects of Annatto (Bixa orellana L.) Seeds Powder on Physicochemical Properties, Antioxidant and Antimicrobial Activities of Pork Patties during Refrigerated Storage

    PubMed Central

    Cuong, Tran Van; Chin, Koo Bok

    2016-01-01

    This study investigated the effect of the powder produced by ball-milling the outer layer of annatto (Bixa orellana L.) seeds on the physicochemical properties as well as the antioxidant and antimicrobial activities of pork patties over 14 d of refrigerated storage (4±1℃). Five pork patty treatments were produced containing three different concentrations of annatto seeds, 0.1, 0.25 and 0.5% (ANT0.1, ANT0.25, ANT0.5), 0.1% ascorbic acid (AA0.1), and a control (CTL). Based on the results, annatto seed powder appeared to show antioxidant activity. The Hunter color values of pork patties were affected by the addition of annatto seed powder, which increased the redness and yellowness values, but decreased the lightness of the patties (p<0.05). To evaluate the antioxidative effects of annatto on pork patties, thiobarbituric acid reactive substances (TBARS) and peroxide values (POV) were analyzed over 14 d of refrigerated storage. Treatments containing annatto seed showed lower TBARS and POV than control (CTL) samples (p<0.05). The volatile basic nitrogen (VBN) of the pork patties containing annatto seeds were lower than that of CTL at the end of storage (p<0.05). Although no differences in total bacterial counts were observed between control and treated patties, those containing annatto seeds had lower microbial counts for Enterobacteriacease than CTL or AA 0.1%. Therefore, annatto seed powder might be a good source of natural antioxidants for the production of meat products.

  18. Biocontrol and plant growth promoting activities of a Streptomyces corchorusii strain UCR3-16 and preparation of powder formulation for application as biofertilizer agents for rice plant.

    PubMed

    Tamreihao, K; Ningthoujam, Debananda S; Nimaichand, Salam; Singh, Elangbam Shanta; Reena, Pascal; Singh, Salam Herojeet; Nongthomba, Upendra

    2016-11-01

    Streptomyces corchorusii strain UCR3-16, obtained from rice rhizospheric soils showed antifungal activities against 6 major rice fungal pathogens by diffusible and volatile compounds production. The strain was found positive for production of fungal cell wall degrading enzymes such as chitinase, β-1,3-glucanase, β-1,4-glucanase, lipase and protease. The strain was also positive for plant growth promoting traits. It produced up to 30.5μg/ml of IAA and solubilized a significant amount of inorganic phosphate (up to 102μg/ml). It also produced 69% siderophore units. The strain also produced ammonia and gave positive result for ACC deaminase activity. Highest vigor index of inoculated seedlings was observed when rice seeds were treated with cell suspension of UCR3-16 corresponding to 4.5×10(8)cfu/ml. Bioinoculant-treated seeds also showed similar results under pathogen challenged conditions. In pot trial experiments, UCR3-16-treated rice plants showed significantly increased growth and grain yield production. Powder formulation of the strain was developed using talcum and corn starch as carriers and the shelf-lives were monitored. Talcum formulation showed higher cell-count than corn starch even after 6 months of storage, and optimum condition for storage of the powder formulation were found to be at 4°C. Pot trial experiments using talcum powder formulation also showed significant positive effects on growth of rice plants. Field trial using talcum powder formulation also exhibited significant enhancement in shoot length and weight of shoot and root, and total grain yield and weight of grains in rice plants. Talcum formulation also significantly reduced the sheath blight disease in rice leaves. PMID:27664745

  19. Effects of Annatto (Bixa orellana L.) Seeds Powder on Physicochemical Properties, Antioxidant and Antimicrobial Activities of Pork Patties during Refrigerated Storage.

    PubMed

    Cuong, Tran Van; Chin, Koo Bok

    2016-01-01

    This study investigated the effect of the powder produced by ball-milling the outer layer of annatto (Bixa orellana L.) seeds on the physicochemical properties as well as the antioxidant and antimicrobial activities of pork patties over 14 d of refrigerated storage (4±1℃). Five pork patty treatments were produced containing three different concentrations of annatto seeds, 0.1, 0.25 and 0.5% (ANT0.1, ANT0.25, ANT0.5), 0.1% ascorbic acid (AA0.1), and a control (CTL). Based on the results, annatto seed powder appeared to show antioxidant activity. The Hunter color values of pork patties were affected by the addition of annatto seed powder, which increased the redness and yellowness values, but decreased the lightness of the patties (p<0.05). To evaluate the antioxidative effects of annatto on pork patties, thiobarbituric acid reactive substances (TBARS) and peroxide values (POV) were analyzed over 14 d of refrigerated storage. Treatments containing annatto seed showed lower TBARS and POV than control (CTL) samples (p<0.05). The volatile basic nitrogen (VBN) of the pork patties containing annatto seeds were lower than that of CTL at the end of storage (p<0.05). Although no differences in total bacterial counts were observed between control and treated patties, those containing annatto seeds had lower microbial counts for Enterobacteriacease than CTL or AA 0.1%. Therefore, annatto seed powder might be a good source of natural antioxidants for the production of meat products. PMID:27621688

  20. Superfine powdered activated carbon (S-PAC) coatings on microfiltration membranes: Effects of milling time on contaminant removal and flux.

    PubMed

    Amaral, Pauline; Partlan, Erin; Li, Mengfei; Lapolli, Flavio; Mefford, O Thompson; Karanfil, Tanju; Ladner, David A

    2016-09-01

    In microfiltration processes for drinking water treatment, one method of removing trace contaminants is to add powdered activated carbon (PAC). Recently, a version of PAC called superfine PAC (S-PAC) has been under development. S-PAC has a smaller particle size and thus faster adsorption kinetics than conventionally sized PAC. Membrane coating performance of various S-PAC samples was evaluated by measuring adsorption of atrazine, a model micropollutant. S-PACs were created in-house from PACs of three different materials: coal, wood, and coconut shell. Milling time was varied to produce S-PACs pulverized with different amounts of energy. These had different particles sizes, but other properties (e.g. oxygen content), also differed. In pure water the coal based S-PACs showed superior atrazine adsorption; all milled carbons had over 90% removal while the PAC had only 45% removal. With addition of calcium and/or NOM, removal rates decreased, but milled carbons still removed more atrazine than PAC. Oxygen content and specific external surface area (both of which increased with longer milling times) were the most significant predictors of atrazine removal. S-PAC coatings resulted in loss of filtration flux compared to an uncoated membrane and smaller particles caused more flux decline than larger particles; however, the data suggest that NOM fouling is still more of a concern than S-PAC fouling. The addition of calcium improved the flux, especially for the longer-milled carbons. Overall the data show that when milling S-PAC with different levels of energy there is a tradeoff: smaller particles adsorb contaminants better, but cause greater flux decline. Fortunately, an acceptable balance may be possible; for example, in these experiments the coal-based S-PAC after 30 min of milling achieved a fairly high atrazine removal (overall 80%) with a fairly low flux reduction (under 30%) even in the presence of NOM. This suggests that relatively short duration (low energy

  1. MDC-Analyzer-facilitated combinatorial strategy for improving the activity and stability of halohydrin dehalogenase from Agrobacterium radiobacter AD1.

    PubMed

    Wang, Xiong; Lin, Hao; Zheng, Yu; Feng, Juan; Yang, Zujun; Tang, Lixia

    2015-07-20

    Halohydrin dehalogenase from Agrobacterium radiobacter AD1 (HheC) displays a broad substrate range with high regio- and enantioselectivity of both ring-closure and ring-opening reactions, making the enzyme a useful catalyst for the production of optically pure epoxides and β-substituted alcohols. In this study, we report a novel method using an MDC-Analyzer-facilitated combinatorial strategy to improve the activity and stability of HheC by simultaneously randomizing multiple contiguous residues. Six contiguous active-site residues, which are the hotspots for improving the activity of HheC, were simultaneously selected and randomized using the MDC-Analyzer-facilitated combinatorial strategy, resulting in a high-quality mutagenesis library. After screening a total of 1152 clones, three positive mutants were obtained, which exhibited approximately 3.5-5.9-fold higher kcat values than the wild-type HheC toward 1,3-dichloro-2-propanol (1,3-DCP). However, the inactivation half-life of the best mutant (DG9) at 55 °C decreased 9-fold compared with that of the wild-type HheC. To improve the stability of mutant DG9, seven contiguous potential surface amino acids were revealed by using the B-FITTER tool. Two charged amino acids, Glu and Lys, which are more abundant in thermophilic proteins than in their mesophilic counterparts, were selected to substitute those seven amino acids and were combined together via an MDC-Analyzer-facilitated combinatorial strategy. Two mutants displaying 1.6- and 2.3-fold higher half-life τ1/2 (55 °C) values than their DG9 template were obtained after screening only 384 clones. The results indicated that an MDC-Analyzer-facilitated combinatorial strategy represents an efficient tool for the directed evolution of functional enzymes with multiple contiguous targeting sites.

  2. Fabrication of cerium active terbium aluminum garnet (TAG:Ce) phosphor powder via the solid-state reaction method

    SciTech Connect

    Tsai, M.-S. Liu, G.-M.; Chung, S.-L.

    2008-05-06

    A modified solid-state reaction method for the formation of terbium aluminum garnet (TAG:Ce) powder was studied. The starting materials, which included terbium oxide (Tb{sub 4}O{sub 7}), boehmite and cerium chloride (CeCl{sub 3}.7H{sub 2}O), were pre-aged at pH 3. This pre-aging process helps to form the core-shell structure, which leads to the formation of TAG:Ce phosphor powder via a solid-state reaction more easily. The emission intensity at 551 nm of the product pre-aged at pH 3 is higher than that formed without pre-aging.

  3. Effect of pretreatment atmosphere on the particle size and oxygen reduction activity of low-loading platinum impregnated titanium carbide powder electrocatalysts

    NASA Astrophysics Data System (ADS)

    Yang, Leerang; Kimmel, Yannick C.; Lu, Qi; Chen, Jingguang G.

    2015-08-01

    Low-loading Pt supported on TiC powder catalysts were synthesized by an impregnation method. After the Pt(NH3)4(NO3)2 precursor was impregnated onto the TiC support, different pretreatment atmospheres were used to study the influence on Pt dispersion, surface composition, and catalytic activity towards oxygen reduction reaction (ORR). Direct reduction of the Pt precursor in hydrogen led to small Pt particles with an average size of ∼2.2 nm and superior ORR activity at low overpotential compared to commercial Pt/C. However, calcination of the Pt precursor in air resulted in larger Pt particles with an average size of ∼6.7 nm and lower ORR specific activity. The decrease in ORR activity was primarily attributed to the surface oxidation of the TiC support during calcination. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) confirmed that the TiC powder was oxidized when the catalyst was calcined in air. The finding reported here demonstrates the importance of pretreatment atmosphere for synthesizing Pt-modified transition metal carbides as highly active electrocatalysts.

  4. The MurE synthetase from Thermotoga maritima is endowed with an unusual D-lysine adding activity.

    PubMed

    Boniface, Audrey; Bouhss, Ahmed; Mengin-Lecreulx, Dominique; Blanot, Didier

    2006-06-01

    The peptidoglycan of Thermotoga maritima, an extremely thermophilic eubacterium, was shown to contain no diaminopimelic acid and approximate amounts of both enantiomers of lysine (Huber, R., Langworthy, T. A., König, H., Thomm, M., Woese, C. R., Sleytr, U. B., and Stetter, K. O. (1986) Arch. Microbiol. 144, 324-333). To assess the possible involvement of the MurE activity in the incorporation of D-lysine, the murE gene from this organism was cloned in Escherichia coli, and the corresponding protein was purified as the C-terminal His6-tagged form. In vitro assays showed that D-lysine and meso-diaminopimelic acid were added to UDP-N-acetylmuramoyl-dipeptide with 25 and 10% efficiencies, respectively, relative to L-lysine. The purified enzyme was used to synthesize the L- and D-lysine-containing UDP-N-acetylmuramoyl-tripeptides; chemical analysis revealed an unusual structure for the D-lysine-containing nucleotide, namely acylation of the epsilon-amino function of D-lysine by the D-glutamyl residue. In vitro assays with MurF and MraY enzymes from T. maritima showed that this novel nucleotide was not a substrate for MurF but that it could be directly processed into tripeptide lipid I by MraY, thereby substantiating the role of MurE in the incorporation of D-lysine into peptidoglycan.

  5. PROCESS OF FORMING POWDERED MATERIAL

    DOEpatents

    Glatter, J.; Schaner, B.E.

    1961-07-14

    A process of forming high-density compacts of a powdered ceramic material is described by agglomerating the powdered ceramic material with a heat- decompossble binder, adding a heat-decompossble lubricant to the agglomerated material, placing a quantity of the material into a die cavity, pressing the material to form a compact, pretreating the compacts in a nonoxidizing atmosphere to remove the binder and lubricant, and sintering the compacts. When this process is used for making nuclear reactor fuel elements, the ceramic material is an oxide powder of a fissionsble material and after forming, the compacts are placed in a cladding tube which is closed at its ends by vapor tight end caps, so that the sintered compacts are held in close contact with each other and with the interior wall of the cladding tube.

  6. Powder treatment process

    DOEpatents

    Weyand, J.D.

    1988-02-09

    Disclosed are: (1) a process comprising spray drying a powder-containing slurry, the slurry containing a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, while reducing the tendency for oxidation of the constituent by including as a liquid constituent of the slurry an organic liquid; (2) a process comprising spray drying a powder-containing slurry, the powder having been pretreated to reduce content of a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, the pretreating comprising heating the powder to react the constituent; and (3) a process comprising reacting ceramic powder, grinding the reacted powder, slurrying the ground powder, spray drying the slurried powder, and blending the dried powder with metal powder. 2 figs.

  7. Powder treatment process

    DOEpatents

    Weyand, John D.

    1988-01-01

    (1) A process comprising spray drying a powder-containing slurry, the slurry containing a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, while reducing the tendency for oxidation of the constituent by including as a liquid constituent of the slurry an organic liquid; (2) a process comprising spray drying a powder-containing slurry, the powder having been pretreated to reduce content of a powder constituent susceptible of oxidizing under the temperature conditions of the spray drying, the pretreating comprising heating the powder to react the constituent; and (3) a process comprising reacting ceramic powder, grinding the reacted powder, slurrying the ground powder, spray drying the slurried powder, and blending the dried powder with metal powder.

  8. Influence of powdered activated carbon addition on water quality, sludge properties, and microbial characteristics in the biological treatment of commingled industrial wastewater.

    PubMed

    Hu, Qing-Yuan; Li, Meng; Wang, Can; Ji, Min

    2015-09-15

    A powdered activated carbon-activated sludge (PAC-AS) system, a traditional activated sludge (AS) system, and a powdered activated carbon (PAC) system were operated to examine the insights into the influence of PAC addition on biological treatment. The average COD removal efficiencies of the PAC-AS system (39%) were nearly double that of the AS system (20%). Compared with the average efficiencies of the PAC system (7%), COD removal by biodegradation in the PAC-AS system was remarkably higher than that in the AS system. The analysis of the influence of PAC on water quality and sludge properties showed that PAC facilitated the removal of hydrophobic matter and metabolic acidic products, and also enhanced the biomass accumulation, sludge settleability, and specific oxygen uptake rate inside the biological system. The microbial community structures in the PAC-AS and AS systems were monitored. The results showed that the average well color development in the PAC-AS system was higher than that in the AS system. The utilization of various substrates by microorganisms in the two systems did not differ. The dissimilarity index was far less than one; thus, showing that the microbial community structures of the two systems were the same.

  9. Influence of powdered activated carbon addition on water quality, sludge properties, and microbial characteristics in the biological treatment of commingled industrial wastewater.

    PubMed

    Hu, Qing-Yuan; Li, Meng; Wang, Can; Ji, Min

    2015-09-15

    A powdered activated carbon-activated sludge (PAC-AS) system, a traditional activated sludge (AS) system, and a powdered activated carbon (PAC) system were operated to examine the insights into the influence of PAC addition on biological treatment. The average COD removal efficiencies of the PAC-AS system (39%) were nearly double that of the AS system (20%). Compared with the average efficiencies of the PAC system (7%), COD removal by biodegradation in the PAC-AS system was remarkably higher than that in the AS system. The analysis of the influence of PAC on water quality and sludge properties showed that PAC facilitated the removal of hydrophobic matter and metabolic acidic products, and also enhanced the biomass accumulation, sludge settleability, and specific oxygen uptake rate inside the biological system. The microbial community structures in the PAC-AS and AS systems were monitored. The results showed that the average well color development in the PAC-AS system was higher than that in the AS system. The utilization of various substrates by microorganisms in the two systems did not differ. The dissimilarity index was far less than one; thus, showing that the microbial community structures of the two systems were the same. PMID:25863578

  10. Evaluation of a two-generation reproduction toxicity study adding endpoints to detect endocrine disrupting activity using lindane.

    PubMed

    Matsuura, Ikuo; Saitoh, Tetsuji; Tani, Einosuke; Wako, Yumi; Iwata, Hiroshi; Toyota, Naoto; Ishizuka, Yoshihito; Namiki, Masato; Hoshino, Nobuhito; Tsuchitani, Minoru; Ikeda, Yasuo

    2005-12-01

    A two-generation reproduction toxicity study in rats adding extra endpoints to detect endocrine disrupting activity was conducted using lindane by dietary administration at 0, 10, 60, and 300 ppm, for investigation of its utility. The extra endpoints included anogenital distance (AGD), nipple development, sexual maturation (vaginal opening and preputial separation), estrous cycle, spermatogenesis, sex organ weights, and blood hormone concentrations (thyroid and sex hormones). F1 offspring were examined for emotionality (open field test), motor coordination (rotarod test), as well as learning and memory (pole-climbing test). Hepatic drug-metabolizing enzyme activities were also measured. The results revealed general toxicological effects on parental animals, influence on reproductive function, and altered development of offspring; however, they did not demonstrate any distinct changes in the extra endpoints for detection of endocrine disrupting activity. Adult toxicity was observed in both F0 and F1 animals, including suppressed body weight gain and reduced food consumption in both sexes, and deaths of females at 300 ppm. Convulsions and irritability were observed during the perinatal period in pregnant F1 females given 300 ppm. Pathological examination revealed increased liver weights and centrilobular hepatocellular hypertrophy in both sexes and generations at 10 or 60 ppm and above; in addition, increased kidney weights and increased hyaline droplets in the proximal tubule epithelium, and basophilic renal tubules in males were noted at 10 ppm and above. Pituitary weights were decreased in F0 females and in F1 males and females and adrenal weights were increased in F1 males and females at 300 ppm; however, no histological changes were observed, and manifestations suggesting endocrine disrupting activity related to these changes were lacking. Hypertrophy of the thyroid follicular epithelium in F0 females at 300 ppm and in F1 males at 60 and 300 ppm, and decreases

  11. Determination of the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon using thermogravimetric analysis

    SciTech Connect

    Hsun-Yu Lin; Chung-Shin Yuan; Wei-Ching Chen; Chung-Hsuang Hung

    2006-11-15

    This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl{sub 2} was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl{sub 2} were 1.75, 0.688, and 0.230 mg of HgCl{sub 2} per gram of powdered activated carbon derived from carbon black at 30, 70, and 150{sup o} for 500 {mu}g/m{sup 3} of HgCl{sub 2}, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer-Emmett-eller (BET) models were used to simulate the adsorption of HgCl{sub 2}. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30{sup o}, whereas the Freundlich isotherm fit the experimental results better at 70 and 150{sup o}. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl{sub 2} by PAC-derived carbon black favored adsorption at various HgCl{sub 2} concentrations and temperatures. 35 refs., 7 figs., 3 tabs.

  12. Effects of ripening duration and rosemary powder addition on salchichon modified sausage quality.

    PubMed

    Jung, Jong-Hyun; Shim, Kwan-Seob; Shin, Daekeun

    2015-05-01

    The ripening durations and ingredients for the Salchichon sausages were modified to increase pork rear leg consumption by Korean consumers. The salchichon, a ripened pork sausage, was produced to evaluate the efficacy of two different ripening durations with and without rosemary powder on salchichon sausage quality, and the treatments were: i) 45 days of ripening without rosemary, ii) 60 days of ripening without rosemary, iii) 45 days of ripening with 0.05% rosemary, and iv) 60 days of ripening with 0.05% rosemary. Significant differences were observed in both moisture and fat content for ripening durations, with the highest moisture and least fat content observed in salchichon modified sausage (SMS) ripened for 45 days. Ripening duration and rosemary addition appeared to influence water activity (aw) of salchichon sausages. The aw of SMS ripened for 45 days was 0.80, whereas the other had aw values <0.80. Lactic acid bacteria were predominant, as Korean traditional fermented red pepper paste was added to sausages; however, the Bacillus cereus population was significantly affected by rosemary powder addition. Chewiness and gumminess decreased significantly due to the addition of rosemary powder compared to SMS without rosemary powder, and both 45 days of ripening and rosemary powder addition influenced the hardness of SMS. In conclusion, ripening duration of SMS for 45 days in the presence of rosemary powder provided superior SMS quality with an economical ripening duration compared to that of ripening with rosemary powder or ripening for 60 days.

  13. DMPP-added nitrogen fertilizer affects soil N2O emission and microbial activity in Southern Italy

    NASA Astrophysics Data System (ADS)

    Vitale, Luca; De Marco, Anna; Maglione, Giuseppe; Polimeno, Franca; Di Tommasi, Paul; Magliulo, Vincenzo

    2014-05-01

    Arable sites contributes to global N2O emission due to massive utilization of nitrogen fertilizers. N2O derives from the biological processes such as nitrification and denitrification influenced by soil nitrogen availability. The use of nitrogen fertilizers added with nitrification inhibitors represents one among the proposed strategy to reduce soil N2O emission form arable sites. The aim of this work was to evaluate the effects of 3,4-dimethylphyrazole phosphate (DMPP), a nitrification inhibitor, on N2O emission and microbial activity of a soil cropped to potato in Southern Italy. The experiment was a randomized block design with two treatments applied and three replicates: control (C) and DMPP (Entec®, K+S Nitrogen) plots, both supplied with the same amount of ammonium nitrate. The nitrogen fertilizer was supplied in three events: at 0 Day After Sowing (DAS; 100 kg N ha-1), at 57 DAS (30 kg N ha-1), and at 71 DAS (30 kg N ha-1). Soil N2O emission was monitored by both dynamic and static chambers. Static chambers were located both on hills and furrows whereas dynamic chambers were located on furrows. Air samples were collected from chambers at different times and analysed by a gas chromatograph (SRI 8610C, Gas Chromatograph). Fluxes were estimated as a linear interpolation of N2O changes over a 30 min time. Microbial biomass and basal respiration were determined as CO2 evolution, analysed by means of an IRGA (Li6200, Licor), on 2 g of fresh soil over a 4h incubation time. Microbial biomass was determined by Substrate Induced Respiration method. Data show no statistical differences in N2O fluxes measured with either dynamic chambers between C and DMPP plots in studied period. However, after the first fertilization event, when the fertilizer was applied as 100 kg N ha-1, the average N2O fluxes measured with static chambers were higher in DMPP plots compared to C plots. In the same period, the microbial biomass significantly decreased in DMPP plots as compared to C

  14. In vivo antioxidant activity of carotenoid powder from tomato byproduct and its use as a source of carotenoids for egg-laying hens.

    PubMed

    Xue, Feng; Li, Chen; Pan, Siyi

    2013-04-25

    Ultrasound treatment was used to extract carotenoids from tomato waste. Gelatin and gum arabic were applied as coating materials for the encapsulation of carotenoids. The first-order reaction was used to determine the degradation of carotenoids in the microcapsules. The result of controlled release studies showed that microcapsules would protect most of the carotenoids from being released in the stomach. We investigated the modifications induced by an oral administration of carotenoid powder on lipid peroxidation, antioxidant enzymes and ion status in liver of rat. The 28 day treatment increased the activity of glutathione peroxidase and manganese superoxide dismutase and reduced malondialdehyde concentration in rat liver. The activity of catalase was not affected by treatment and greater iron concentration was found in liver from treatment groups. However, there was no dose-dependent change of antioxidant enzyme activity or malondialdehyde concentration with increasing carotenoid consumption. Furthermore, carotenoid powder was able to be used as forage material for egg-laying hens. The 28 day treatment did not affect the egg performance, but significantly increased yolk colour parameters and lycopene content. PMID:23385978

  15. Activation of consolidation processes of alumina ceramics

    NASA Astrophysics Data System (ADS)

    Matrenin, S. V.; Zenin, B. S.; Tayukin, R. V.

    2016-02-01

    The methods for activating sintering ceramics based on Al2O3 by mechanical activation in the planetary mill, by adding in the mixture of nanopowders (NP) Al, Al2O3, and submicron powder TiO2, and by applying the technology of spark plasma sintering (SPS) are developed. It has been shown that adding the nanopowder up to 20 wt. % Al2O3 in a coarse powder α-Al2O3 activates the sintering process resulting in increased density and hardness of the sintered alumina ceramics. Substantial effect of increasing density of alumina ceramics due to adding the submicron powder TiO2 in the compound of initial powder mixtures has been established.

  16. Chromospherically active stars. 12: ADS 11060 C: A double lined K dwarf binary in a quintuple system

    NASA Technical Reports Server (NTRS)

    Fekel, Francis C.; Henry, Gregory W.; Hampton, Melissa L.; Fried, Robert; Morton, Mary D.

    1994-01-01

    ADS 11060 C is a double lined spectroscopic binary with a period of 25.7631 days and an eccentricity of 0.565. Spectral types of the two stars are estimated as K7 V and MO V with a magnitude difference of about 0.55 mag in V. The stars appear to be somewhat metal rich with respect to the Sun. Despite the relatively large masses of 0.53 and 0.51 solar mass, our photometric observations find no evidence for eclipses and we estimate an inclination of 77 deg plus or minus 11 deg. ADS 11060 C is, however, photometrically variable with a period of 9 plus or minus 1 day and an amplitude of 0.05 mag in V. Thus, it is a newly identified BY Draconis variable. The center-of-mass velocity of ADS 11060 C and an estimated parallax of 0.030 sec support its physical association with ADS 11060 AB, making this a quintuple system. The projected separation of the AB-C system is nearly 1200 AU. Although the log lithium abundances of the two components of ADS 11060 C are only upper limits, less than or equal to -0.14, lithium abundances of the AB-C components appear to be consistent with those of similar stars in the alpha Persei and Pleiades clusters, suggesting an age of about 70 Myr for ADS 11060 AB-C. The system is a possible member of the Pleiades moving group. Listed as an optical counterpart to a source in the ROSAT Wide Field Camera extreme-ultraviolet bright source catalog, both ADS 11060 AB and C may contribute to the observed flux.

  17. [Zeolite-containing tripoli powder in experimental hepatology].

    PubMed

    Kolotilova, M L; Ivanov, L N

    2005-01-01

    Biological activity of zeolite-containing tripoli powder was studied in rats. Biochemical, enzymatic and lipid peroxidation indices were assessed. The results of the study confirm enterosorption and detoxication activity of the powder.

  18. Preparation of titanium diboride powder

    DOEpatents

    Brynestad, Jorulf; Bamberger, Carlos E.

    1985-01-01

    Finely-divided titanium diboride or zirconium diboride powders are formed by reacting gaseous boron trichloride with a material selected from the group consisting of titanium powder, zirconium powder, titanium dichloride powder, titanium trichloride powder, and gaseous titanium trichloride.

  19. Preparation of metal diboride powders

    DOEpatents

    Brynestad, J.; Bamberger, C.E.

    Finely-divided titanium diboride or zirconium diboride powders are formed by reacting gaseous boron trichloride with a material selected from the group of consisting of titanium powder, zirconium powder, titanium dichloride powder, titanium trichloride powder, and gaseous titanium trichloride.

  20. Characterization of Fine Powders

    NASA Astrophysics Data System (ADS)

    Krantz, Matthew; Zhang, Hui; Zhu, Jesse

    Fine powders are used in many applications and across many industries such as powdered paints and pigments, ceramics, petrochemicals, plastics, pharmaceuticals, and bulk and fine chemicals, to name a few. In addition, fine powders must often be handled as a waste by-product, such as ash generated in combustion and gasification processes. In order to correctly design a process and process equipment for application and handling of powders, especially fine powders, it is essential to understand how the powder would behave. Many characterization techniques are available for determining the flow properties of powders; however, care must be taken in selecting the most appropriate technique(s).

  1. DIS in AdS

    SciTech Connect

    Albacete, Javier L.; Kovchegov, Yuri V.; Taliotis, Anastasios

    2009-03-23

    We calculate the total cross section for the scattering of a quark-anti-quark dipole on a large nucleus at high energy for a strongly coupled N = 4 super Yang-Mills theory using AdS/CFT correspondence. We model the nucleus by a metric of a shock wave in AdS{sub 5}. We then calculate the expectation value of the Wilson loop (the dipole) by finding the extrema of the Nambu-Goto action for an open string attached to the quark and antiquark lines of the loop in the background of an AdS{sub 5} shock wave. We find two physically meaningful extremal string configurations. For both solutions we obtain the forward scattering amplitude N for the quark dipole-nucleus scattering. We study the onset of unitarity with increasing center-of-mass energy and transverse size of the dipole: we observe that for both solutions the saturation scale Q{sub s} is independent of energy/Bjorken-x and depends on the atomic number of the nucleus as Q{sub s}{approx}A{sup 1/3}. Finally we observe that while one of the solutions we found corresponds to the pomeron intercept of {alpha}{sub P} = 2 found earlier in the literature, when extended to higher energy or larger dipole sizes it violates the black disk limit. The other solution we found respects the black disk limit and yields the pomeron intercept of {alpha}{sub P} = 1.5. We thus conjecture that the right pomeron intercept in gauge theories at strong coupling may be {alpha}{sub P} = 1.5.

  2. Active wear and failure mechanisms of TiN-coated high speed steel and TiN-coated cemented carbide tools when machining powder metallurgically made stainless steels

    SciTech Connect

    Jiang, L.; Haenninen, H.; Paro, J.; Kauppinen, V.

    1996-09-01

    In this study, active wear and failure mechanisms of both TiN-coated high speed steel and TiN-coated cemented carbide tools when machining stainless steels made by powder metallurgy in low and high cutting speed ranges, respectively, have been investigated. Abrasive wear mechanisms, fatigue-induced failure, and adhesive and diffusion wear mechanisms mainly affected the tool life of TiN-coated high speed steel tools at cutting speeds below 35 m/min, between 35 and 45 m/min, and over 45 m/min, respectively. Additionally, fatigue-induced failure was active at cutting speeds over 45 m/min in the low cutting speed range when machining powder metallurgically made duplex stainless steel 2205 and austenitic stainless steel 316L. In the high cutting speed range, from 100 to 250 m/min, fatigue-induced failure together with diffusion wear mechanism, affected the tool life of TiN-coated cemented carbide tools when machining both 316L and 2205 stainless steels. It was noticed that the tool life of TiN-coated high speed steel tools used in the low cutting speed range when machining 2205 steel was longer than that when machining 316L steel, whereas the tool life of TiN-coated cemented carbide tools used in the high cutting speed range when machining 316L steel was longer than that when machining 2205 steel.

  3. Phenyl-functionalized magnetic palm-based powdered activated carbon for the effective removal of selected pharmaceutical and endocrine-disruptive compounds.

    PubMed

    Wong, Kien Tiek; Yoon, Yeomin; Snyder, Shane A; Jang, Min

    2016-06-01

    Triethoxyphenylsilane (TEPS)-functionalized magnetic palm-based powdered activated carbon (MPPAC-TEPS) was prepared and characterized using various spectroscopic methods, and then tested for the removal of bisphenol A, carbamazepine, ibuprofen and clofibric acid. Magnetite film on MPPAC-TEPS was homogeneously coated on the outer surface of palm-based powdered activated carbon (PPAC) through a hydrothermal co-precipitation technique. Followed by silanization of phenyl-functionalized organosilane on MPPAC's magnetic film. As results, micro/mesopore surface area and volume increased without significant pore clogging and iron (Fe) dissolution under the acidic conditions was greatly decreased. The unique structural and chemical features of MPPAC-TEPS were found to be the main reasons for the enhanced adsorption rates and removal capacities of POPs. The presence of electrolytes and different pH values greatly affected the sorption efficiencies. The dominant sorption mechanism of POPs by MPPAC-TEPS was determined to be π-π interaction (physisorption), based on thermodynamic (ΔG°) and differential scanning calorimetry (DSC). Thermal regeneration at a low temperature (350 °C) was an effective method to desorb the retained POPs and enabled to reactivate MPPAC-TEPS with sustained sorption rates and capacities, whereas PPAC was largely exhausted. As a new type of sorbent for POPs, MPPAC-TEPS has operational advantages, such as magnetic separation and stable regeneration. PMID:26963238

  4. [Value-Added--Adding Economic Value in the Food Industry].

    ERIC Educational Resources Information Center

    Welch, Mary A., Ed.

    1989-01-01

    This booklet focuses on the economic concept of "value added" to goods and services. A student activity worksheet illustrates how the steps involved in processing food are examples of the concept of value added. The booklet further links food processing to the idea of value added to the Gross National Product (GNP). Discussion questions, a student…

  5. Al-TiC Composites Fabricated by a Thermally Activated Reaction Process in an Al Melt Using Al-Ti-C-CuO Powder Mixtures. Part I: Microstructural Evolution and Reaction Mechanism

    NASA Astrophysics Data System (ADS)

    Cho, Young-Hee; Lee, Jung-Moo; Kim, Su-Hyeon

    2014-11-01

    Al matrix composites reinforced with TiC particles are fabricated by a thermally activated reaction of Al-Ti-C powder mixtures in an Al melt. In the presence of CuO, reactant mixtures in the form of a pellet added to molten Al at temperatures higher than 1093 K (820 °C) instantly reach the peak temperature over 1785 K (1512 °C), followed by combustion wave propagation with in situ synthesizing TiC with a size of approximately 1 μm. Incomplete reaction products such as unreacted C, Al3Ti, and TiC aggregates are also observed. The pellet microstructure evolution upon the combustion reaction indicates that preheating temperature, i.e., the initial melt temperature, affects both the thermodynamic and kinetic characteristics of the reaction, and thereby influences the final microstructure of the Al/TiC composites. Based on the experimental and theoretical results, a sequence of the reaction leading upto the in situ synthesis of TiC is illustrated and the corresponding mechanism for the present process is proposed.

  6. Novel Inhaled Combination Powder Containing Amorphous Colistin and Crystalline Rifapentine with Enhanced Antimicrobial Activities against Planktonic Cells and Biofilm of Pseudomonas aeruginosa for Respiratory Infections.

    PubMed

    Zhou, Qi Tony; Sun, Si-Ping; Chan, John Gar Yan; Wang, Ping; Barraud, Nicolas; Rice, Scott A; Wang, Jiping; Li, Jian; Chan, Hak-Kim

    2015-08-01

    Colistin has been increasingly used for the treatment of respiratory infections caused by Gram-negative bacteria. Unfortunately parenteral administration of colistin can cause severe adverse effects. This study aimed to develop an inhaled combination dry powder formulation of colistin and rifapentine for the treatment of respiratory infections. The combination formulation was produced by spray-drying rifapentine particles suspended in an aqueous colistin solution. The combination dry powder had enhanced antimicrobial activities against planktonic cells and biofilm cultures of Pseudomonas aeruginosa, with both minimum inhibitory concentration (MIC) and minimum biofilm inhibitory concentration (MBIC) values (2 and 4 mg/L, respectively) being half that of pure colistin (MIC 4 mg/L and MBIC 8 mg/L) and 1/16th that of pure rifapentine (MIC 32 mg/L and MBIC 64 mg/L). High aerosol performance, as measured via an Aerolizer device, was observed with emitted doses>89% and fine particle fraction (FPF) total>76%. The proportion of submicron particles of rifapentine particles was minimized by the attachment of colistin, which increased the overall particle mass and aerodynamic size distribution. Using the spray-drying method described here, stable particles of amorphous colistin and crystalline rifapentine were distributed homogeneously in each stage of the impinger. Unlike the colistin alone formulation, no deterioration in aerosol performance was found for the combination powder when exposed to a high relative humidity of 75%. In our previous study, surface coating by rifampicin contributed to the moisture protection of colistin. Here, a novel approach with a new mechanism was proposed whereby moisture protection was attributed to the carrier effect of elongated crystalline rifapentine particles, which minimized contact between hygroscopic colistin particles. This inhaled combination antibiotic formulation with enhanced aerosol dispersion efficiency and in vitro efficacy

  7. The "aged garlic extract:" (AGE) and one of its active ingredients S-allyl-L-cysteine (SAC) as potential preventive and therapeutic agents for Alzheimer's disease (AD).

    PubMed

    Ray, B; Chauhan, N B; Lahiri, D K

    2011-01-01

    Alzheimer's disease (AD) is the most common form of dementia in the older people and 7(th) leading cause of death in the United States. Deposition of amyloid-beta (Aβ) plaques, hyperphosphorylation of microtubule associated protein tau (MAPT), neuroinflammation and cholinergic neuron loss are the major hallmarks of AD. Deposition of Aβ peptides, which takes place years before the clinical onset of the disease can trigger hyperphophorylation of tau proteins and neuroinflammation, and the latter is thought to be primarily involved in neuronal and synaptic damage seen in AD. To date, four cholinesterase inhibitors or ChEI (tacrine, rivastigmine, donepezil and galantamine) and a partial NMDA receptor antagonist (memantine) are the only approved treatment options for AD. However, these drugs fail to completely cure the disease, which warrants a search for newer class of targets that would eventually lead to effective drugs for the treatment of AD. In addition to selected pharmacological agents, botanical and medicinal plant extracts are also being investigated. Apart from its culinary use, garlic (Allium sativum) is being used to treat several ailments like cancer and diabetes. Herein we have discussed the effects of a specific 'Aged Garlic Extract' (AGE) and one of its active ingredients, S-allyl-L-cysteine (SAC) in restricting several pathological cascades related to the synaptic degeneration and neuroinflammatory pathways associated with AD. Thus, based on the reported positive preliminary results reviewed herein, further research is required to develop the full potential of AGE and/or SAC into an effective preventative strategy for AD. PMID:21728972

  8. Active Gold-Ceria and Gold-Ceria/titania Catalysts for CO Oxidation. From Single-Crystal Model Catalysts to Powder Catalysts

    SciTech Connect

    Rodriguez, Jose A.; Si, Rui; Evans, Jaime; Xu, Wenqian; Hanson, Jonathan C.; Tao, Jing; Zhu, Yimei

    2014-07-23

    We studied CO oxidation on model and powder catalysts of Au-CeO2 and Au-CeOx/TiO2. Phenomena observed in Au-CeO2(1 1 1) and Au-CeO2/TiO2(1 1 0) provided useful concepts for designing and preparing highly active and stable Au-CeOx/TiO2 powder catalysts for CO oxidation. Small particles of Au dispersed on CeO2(1 1 1) displayed high catalytic activity, making Au-CeO2(1 1 1) a better CO oxidation catalyst than Au-TiO2(1 1 0) or Au-MgO(1 0 0). An excellent support for gold was found after depositing nanoparticles of ceria on TiO2(1 1 0). The CeOx nanoparticles act as nucleation centers for gold, improving dispersion of the supported metal and helping in the creation of reaction sites efficient for the adsorption of CO and the dissociation of the O2 molecule. High-surface area catalysts were prepared by depositing gold on ceria nanorods and CeOx/TiO2 powders. The samples were tested for the low-temperature (10–70 °C) oxygen-rich (1%CO/4%O2/He) CO oxidation reaction after pre-oxidation (20%O2/He, 300 °C) and pre-reduction (5%H2/He, 300 °C) treatments. Moreover, synchrotron-based operando X-ray diffraction (XRD) and X-ray absorption (XAS) spectroscopy were used to study the Au-CeO2 and Au-CeOx/TiO2 catalysts under reaction conditions. Our operando findings indicate that the most active phase of these catalysts for low-temperature CO oxidation consist of small particles of metallic Au dispersed on CeO2 or CeOx/TiO2.

  9. A combination of molecular dynamics and docking calculations to explore the binding mode of ADS-J1, a polyanionic compound endowed with anti-HIV-1 activity.

    PubMed

    Manetti, Fabrizio; Tintori, Cristina; Armand-Ugón, Mercedes; Clotet-Codina, Imma; Massa, Silvio; Ragno, Rino; Esté, José A; Botta, Maurizio

    2006-01-01

    The HIV-1 entry process is an important target for the design of new pharmaceuticals for the multidrug therapy of AIDS. A lot of polyanionic compounds, such as polysulfonated and polysulfated, are reported in the literature for their ability to block early stages of HIV-1 replication. Several studies have been performed to elucidate the mechanism of the anti-HIV-1 activity of sulfated polysaccharides and polyanions in general, including binding to cell surface CD4 and interfering with the gp120-coreceptor interaction. Here, we show molecular modeling investigations on ADS-J1, a polyanionic compound with anti-HIV activity that is able to interfere with gp120-coreceptor interactions. Agreeing with experimental data, computer simulations suggested that the V3 loop of gp120 was the preferential binding site for ADS-J1 onto HIV-1. Moreover, mutations induced by the inhibitor significantly changed the stereoelectronic properties of the gp120 surface, justifying a marked drop in the affinity of ADS-J1 toward an ADS-J1-resistant HIV-1 strain.

  10. Geosmin and 2-methylisoborneol removal using superfine powdered activated carbon: shell adsorption and branched-pore kinetic model analysis and optimal particle size.

    PubMed

    Matsui, Yoshihiko; Nakao, Soichi; Taniguchi, Takuma; Matsushita, Taku

    2013-05-15

    2-Methylisoborneol (MIB) and geosmin are naturally occurring compounds responsible for musty-earthy taste and odor in public drinking-water supplies, a severe problem faced by many utilities throughout the world. In this study, we investigated adsorptive removal of these compounds by superfine powdered activation carbon (SPAC, particle size <1 μm) produced by novel micro-grinding of powdered activated carbon; we also discuss the optimization of carbon particle size to efficiently enhance the adsorptive removal. After grinding, the absorptive capacity remained unchanged for a 2007 carbon sample and was increased for a 2010 carbon sample; the capacity increase was quantitatively described by the shell adsorption model, in which MIB and geosmin adsorbed more in the exterior of a carbon particle than in the center. The extremely high uptake rates of MIB and geosmin by SPAC were simulated well by a combination of the branched-pore kinetic model and the shell adsorption model, in which intraparticle diffusion through macropores was followed by diffusion from macropore to micropore. Simulations suggested that D40 was on the whole the best characteristic diameter to represent a size-disperse group of adsorbent particles; D40 is the diameter through which 40% of the particles by volume pass. Therefore, D40 can be used as an index for evaluating the improvement of adsorptive removal that resulted from pulverization. The dose required for a certain percentage removal of MIB or geosmin decreased linearly with carbon particle size (D40), but the dose reduction became less effective as the activated carbon was ground down to smaller sizes around a critical value of D40. For a 60-min contact time, critical D40 was 2-2.5 μm for MIB and 0.4-0.5 μm for geosmin. The smaller critical D40 was when the shorter the carbon-water contact time was or the slower the intraparticle mass transfer rate of an adsorbate was. PMID:23528781

  11. Geosmin and 2-methylisoborneol removal using superfine powdered activated carbon: shell adsorption and branched-pore kinetic model analysis and optimal particle size.

    PubMed

    Matsui, Yoshihiko; Nakao, Soichi; Taniguchi, Takuma; Matsushita, Taku

    2013-05-15

    2-Methylisoborneol (MIB) and geosmin are naturally occurring compounds responsible for musty-earthy taste and odor in public drinking-water supplies, a severe problem faced by many utilities throughout the world. In this study, we investigated adsorptive removal of these compounds by superfine powdered activation carbon (SPAC, particle size <1 μm) produced by novel micro-grinding of powdered activated carbon; we also discuss the optimization of carbon particle size to efficiently enhance the adsorptive removal. After grinding, the absorptive capacity remained unchanged for a 2007 carbon sample and was increased for a 2010 carbon sample; the capacity increase was quantitatively described by the shell adsorption model, in which MIB and geosmin adsorbed more in the exterior of a carbon particle than in the center. The extremely high uptake rates of MIB and geosmin by SPAC were simulated well by a combination of the branched-pore kinetic model and the shell adsorption model, in which intraparticle diffusion through macropores was followed by diffusion from macropore to micropore. Simulations suggested that D40 was on the whole the best characteristic diameter to represent a size-disperse group of adsorbent particles; D40 is the diameter through which 40% of the particles by volume pass. Therefore, D40 can be used as an index for evaluating the improvement of adsorptive removal that resulted from pulverization. The dose required for a certain percentage removal of MIB or geosmin decreased linearly with carbon particle size (D40), but the dose reduction became less effective as the activated carbon was ground down to smaller sizes around a critical value of D40. For a 60-min contact time, critical D40 was 2-2.5 μm for MIB and 0.4-0.5 μm for geosmin. The smaller critical D40 was when the shorter the carbon-water contact time was or the slower the intraparticle mass transfer rate of an adsorbate was.

  12. Preparation and caracterization of TiO{2} powder photocatalysts. Comparative studies of photocatalytic activity in the degradation of β-naphthol

    NASA Astrophysics Data System (ADS)

    Qourzal, S.; Tamimi, M.; Assabbane, A.; Nounah, A.; Maroufi, N.; Bouamrane, A.; Ichou, Y. Ait

    2005-03-01

    Titanium dioxide TiO{2} powder photocatalysts were prepared at the laboratory by two methods: hydrolysis of titanium tetraisopropoxide (TTIP) and the precipitation of a precursor starting from titanium tetrachloride TiCl{4} in basic medium. The products obtained are calcined at temperatures around 800° C. Their characterization was carried out by both diffraction X-ray (XRD) and thermogravimetric analysis (TGA). The photocatalytic activity of the elaborate solids (TiO{2}) is evaluated. It is compared with that given for commercial TiO{2} “Degussa P-25” in the degradation of β-naphthol chosen as an model molecule in aqueous suspension. These reactions are done at room temperature in a photochemical reactor.

  13. Composite powder particles

    NASA Technical Reports Server (NTRS)

    Parker, Donald S. (Inventor); MacDowell, Louis G. (Inventor)

    2009-01-01

    A liquid coating composition including a coating vehicle and composite powder particles disposed within the coating vehicle. Each composite powder particle may include a magnesium component, a zinc component, and an indium component.

  14. Precision powder feeder

    DOEpatents

    Schlienger, M. Eric; Schmale, David T.; Oliver, Michael S.

    2001-07-10

    A new class of precision powder feeders is disclosed. These feeders provide a precision flow of a wide range of powdered materials, while remaining robust against jamming or damage. These feeders can be precisely controlled by feedback mechanisms.

  15. Evidence of active tectonics on a Roman aqueduct system (II-III century A.D.) near Rome, Italy

    NASA Astrophysics Data System (ADS)

    Marra, Fabrizio; Montone, Paola; Pirro, Mario; Boschi, Enzo

    2004-04-01

    In this paper we describe evidence of strong tectonic deformation affecting two aqueducts of Roman age (II-III century A.D.). The channels are located approximately 20 km northeast of Rome along the ancient Via Tiburtina. Brittle and ductile deformation affects these two structures, including extensional joint systems, NE-oriented faults, and horizontal distortion. This deformation is consistent with right-lateral movement on major N-striking faults, and represents the first evidence that tectonic deformation took place in historical times in the vicinity of Rome, with local strike-slip movement superimposed on a regional extensional fault system.

  16. Aluminum powder metallurgy processing

    SciTech Connect

    Flumerfelt, J.F.

    1999-02-12

    The objective of this dissertation is to explore the hypothesis that there is a strong linkage between gas atomization processing conditions, as-atomized aluminum powder characteristics, and the consolidation methodology required to make components from aluminum powder. The hypothesis was tested with pure aluminum powders produced by commercial air atomization, commercial inert gas atomization, and gas atomization reaction synthesis (GARS). A comparison of the GARS aluminum powders with the commercial aluminum powders showed the former to exhibit superior powder characteristics. The powders were compared in terms of size and shape, bulk chemistry, surface oxide chemistry and structure, and oxide film thickness. Minimum explosive concentration measurements assessed the dependence of explosibility hazard on surface area, oxide film thickness, and gas atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization oxidation of aluminum powder. An Al-Ti-Y GARS alloy exposed in ambient air at different temperatures revealed the effect of reactive alloy elements on post-atomization powder oxidation. The pure aluminum powders were consolidated by two different routes, a conventional consolidation process for fabricating aerospace components with aluminum powder and a proposed alternative. The consolidation procedures were compared by evaluating the consolidated microstructures and the corresponding mechanical properties. A low temperature solid state sintering experiment demonstrated that tap densified GARS aluminum powders can form sintering necks between contacting powder particles, unlike the total resistance to sintering of commercial air atomization aluminum powder.

  17. A Glutathione S-Transferase with Activity towards cis-1,2-Dichloroepoxyethane Is Involved in Isoprene Utilization by Rhodococcus sp. Strain AD45

    PubMed Central

    van Hylckama Vlieg, Johan E. T.; Kingma, Jaap; van den Wijngaard, Arjan J.; Janssen, Dick B.

    1998-01-01

    Rhodococcus sp. strain AD45 was isolated from an enrichment culture on isoprene (2-methyl-1,3-butadiene). Isoprene-grown cells of strain AD45 oxidized isoprene to 3,4-epoxy-3-methyl-1-butene, cis-1,2-dichloroethene to cis-1,2-dichloroepoxyethane, and trans-1,2-dichloroethene to trans-1,2-dichloroepoxyethane. Isoprene-grown cells also degraded cis-1,2-dichloroepoxyethane and trans-1,2-dichloroepoxyethane. All organic chlorine was liberated as chloride during degradation of cis-1,2-dichloroepoxyethane. A glutathione (GSH)-dependent activity towards 3,4-epoxy-3-methyl-1-butene, epoxypropane, cis-1,2-dichloroepoxyethane, and trans-1,2-dichloroepoxyethane was detected in cell extracts of cultures grown on isoprene and 3,4-epoxy-3-methyl-1-butene. The epoxide-degrading activity of strain AD45 was irreversibly lost upon incubation of cells with 1,2-epoxyhexane. A conjugate of GSH and 1,2-epoxyhexane was detected in cell extracts of cells exposed to 1,2-epoxyhexane, indicating that GSH is the physiological cofactor of the epoxide-transforming activity. The results indicate that a GSH S-transferase is involved in the metabolism of isoprene and that the enzyme can detoxify reactive epoxides produced by monooxygenation of chlorinated ethenes. PMID:9687433

  18. Improvement of charging characteristics of coating powders in electrostatic powder coating system

    NASA Astrophysics Data System (ADS)

    Takeuchi, Manabu

    2008-12-01

    The charging characteristics of coating powders were improved for both corona-charging and tribocharging type spray guns. The blow-off measurements showed that the charge-to-mass ratio of coating powders deposited on the substrate was larger than that of undeposited powders for both types of spray gun. The charge-to-mass ratio of the coating powders was increased by adding a pair of auxiliary electrode to the corona-charging spray gun. Free ions from the corona-charging spray gun were decreased by applying a magnetic field in the spraying space. The polymer tube of a tribocharging spray gun that contained a negative charge control agent was able to charge all the coating powders sufficiently positive

  19. Effect of E-beam treatment on the chemistry and on the antioxidant activity of lycopene from dry tomato peel and tomato powder.

    PubMed

    Gámez, M Carmen; Calvo, Marta M; Selgas, M Dolores; García, M Luisa; Erler, Katrin; Böhm, Volker; Catalano, Assunta; Simone, Rossella; Palozza, Paola

    2014-02-19

    Tomato powder (TP) and dry tomato peel (DTP) have been previously used in our laboratory as a source of lycopene to manufacture meat products ready-to-eat (RTE) submitted to E-beam irradiation with good technological and sensory results. Present work describes the studies performed in order to investigate the effect of radiation on chemical changes and antioxidant properties of lycopene. DTP and TP were irradiated (4 kGy). Changes on lycopene were analyzed by HPLC; inhibition of reactive oxygen species (ROS), possible modulation of mitogen-activated protein kinases (MAPK) cascade, nuclear factor κ-light-chain-enhancer of activated B cells (NP-κB) activation and expression of proteins involved in oxidation stress were analyzed in RAT-1 fibroblasts cell culture. Radiation reduced the content of all-E-lycopene and increased (Z)-lycopene, lycopene isomerization, and degradation being higher in DTP than in TP. E-Beam treatment increased the antioxidant ability of both DTP and TP in inhibiting spontaneous and H2O2-induced oxidative stress in cultured fibroblasts. Antioxidant activity was higher in DTP than in TP samples.

  20. Effect of E-beam treatment on the chemistry and on the antioxidant activity of lycopene from dry tomato peel and tomato powder.

    PubMed

    Gámez, M Carmen; Calvo, Marta M; Selgas, M Dolores; García, M Luisa; Erler, Katrin; Böhm, Volker; Catalano, Assunta; Simone, Rossella; Palozza, Paola

    2014-02-19

    Tomato powder (TP) and dry tomato peel (DTP) have been previously used in our laboratory as a source of lycopene to manufacture meat products ready-to-eat (RTE) submitted to E-beam irradiation with good technological and sensory results. Present work describes the studies performed in order to investigate the effect of radiation on chemical changes and antioxidant properties of lycopene. DTP and TP were irradiated (4 kGy). Changes on lycopene were analyzed by HPLC; inhibition of reactive oxygen species (ROS), possible modulation of mitogen-activated protein kinases (MAPK) cascade, nuclear factor κ-light-chain-enhancer of activated B cells (NP-κB) activation and expression of proteins involved in oxidation stress were analyzed in RAT-1 fibroblasts cell culture. Radiation reduced the content of all-E-lycopene and increased (Z)-lycopene, lycopene isomerization, and degradation being higher in DTP than in TP. E-Beam treatment increased the antioxidant ability of both DTP and TP in inhibiting spontaneous and H2O2-induced oxidative stress in cultured fibroblasts. Antioxidant activity was higher in DTP than in TP samples. PMID:24475969

  1. (±)-Japonicols A-D, Acylphloroglucinol-Based Meroterpenoid Enantiomers with Anti-KSHV Activities from Hypericum japonicum.

    PubMed

    Hu, Linzhen; Xue, Yongbo; Zhang, Jinwen; Zhu, Hucheng; Chen, Chunmei; Li, Xiao-Nian; Liu, Junjun; Wang, Zhenzhen; Zhang, Yu; Zhang, Yonghui

    2016-05-27

    (±)-Japonicols A-D (1a/1b-4a/4b), four pairs of new phloroglucinol-based terpenoid enantiomers, were isolated from Hypericum japonicum. Their absolute configurations were confirmed through comparison of their experimental and calculated electronic circular dichroism spectra and single-crystal X-ray diffraction analyses. Compounds 1a/1b, 2a/2b, and 3a/3b possess 2-oxabicyclo[3.3.1]nonane, pyrano[3,2-b]pyran, and benzo[b]cyclopenta[e]oxepine ring systems, respectively. The effects of the phloroglucinols on anti-Kaposi's sarcoma-associated herpesvirus were assessed, and 2a exhibited a moderate inhibitory effect, with an EC50 value of 8.75 μM and a selectivity index of 16.06. PMID:27116034

  2. Acute effects of active gaming on ad libitum energy intake and appetite sensations of 8-11-year-old boys.

    PubMed

    Allsop, Susan; Dodd-Reynolds, Caroline J; Green, Benjamin P; Debuse, Dorothée; Rumbold, Penny L S

    2015-12-28

    The present study examined the acute effects of active gaming on energy intake (EI) and appetite responses in 8-11-year-old boys in a school-based setting. Using a randomised cross-over design, twenty-one boys completed four individual 90-min gaming bouts, each separated by 1 week. The gaming bouts were (1) seated gaming, no food or drink; (2) active gaming, no food or drink; (3) seated gaming with food and drink offered ad libitum; and (4) active gaming with food and drink offered ad libitum. In the two gaming bouts during which foods and drinks were offered, EI was measured. Appetite sensations - hunger, prospective food consumption and fullness - were recorded using visual analogue scales during all gaming bouts at 30-min intervals and at two 15-min intervals post gaming. In the two bouts with food and drink, no significant differences were found in acute EI (MJ) (P=0·238). Significant differences were detected in appetite sensations for hunger, prospective food consumption and fullness between the four gaming bouts at various time points. The relative EI calculated for the two gaming bouts with food and drink (active gaming 1·42 (sem 0·28) MJ; seated gaming 2·12 (sem 0·25) MJ) was not statistically different. Acute EI in response to active gaming was no different from seated gaming, and appetite sensations were influenced by whether food was made available during the 90-min gaming bouts. PMID:26435259

  3. Acute effects of active gaming on ad libitum energy intake and appetite sensations of 8-11-year-old boys.

    PubMed

    Allsop, Susan; Dodd-Reynolds, Caroline J; Green, Benjamin P; Debuse, Dorothée; Rumbold, Penny L S

    2015-12-28

    The present study examined the acute effects of active gaming on energy intake (EI) and appetite responses in 8-11-year-old boys in a school-based setting. Using a randomised cross-over design, twenty-one boys completed four individual 90-min gaming bouts, each separated by 1 week. The gaming bouts were (1) seated gaming, no food or drink; (2) active gaming, no food or drink; (3) seated gaming with food and drink offered ad libitum; and (4) active gaming with food and drink offered ad libitum. In the two gaming bouts during which foods and drinks were offered, EI was measured. Appetite sensations - hunger, prospective food consumption and fullness - were recorded using visual analogue scales during all gaming bouts at 30-min intervals and at two 15-min intervals post gaming. In the two bouts with food and drink, no significant differences were found in acute EI (MJ) (P=0·238). Significant differences were detected in appetite sensations for hunger, prospective food consumption and fullness between the four gaming bouts at various time points. The relative EI calculated for the two gaming bouts with food and drink (active gaming 1·42 (sem 0·28) MJ; seated gaming 2·12 (sem 0·25) MJ) was not statistically different. Acute EI in response to active gaming was no different from seated gaming, and appetite sensations were influenced by whether food was made available during the 90-min gaming bouts.

  4. Multielement determination of heavy metals in water samples by continuous powder introduction microwave-induced plasma atomic emission spectrometry after preconcentration on activated carbon

    NASA Astrophysics Data System (ADS)

    Jankowski, Krzysztof; Yao, Jun; Kasiura, Krzysztof; Jackowska, Adrianna; Sieradzka, Anna

    2005-03-01

    A novel continuous powder introduction microwave-induced plasma atomic emission spectrometry method (CPI-MIP-AES) has been developed for trace determination of metals in ground and tap water samples after preconcentration on activated carbon. The experimental setup consisted of integrated rectangular cavity TE 101 and vertically positioned plasma torch. The technical arrangement of the sample introduction system has been designed based on the fluidized bed concept. The satisfactory signal stability required for sequential analysis was attained owing to the vertical plasma configuration, as well as the plasma gas flow rate compatibility with sample introduction flow rate. The elements of interest (Cd, Cu, Cr, Fe, Mn, Pb, Zn) were preconcentrated in a batch procedure at pH 8-8.5 after addition of activated carbon and then, after filtering and drying of the activated carbon suspension, introduced to the MIP by the CPI system. An enrichment factor of about 1000-fold for a sample volume of 1 l was obtained. The detection limit values for the proposed method were 17-250 ng l -1. The proposed method was validated by analyzing the certified reference materials: SRW "Warta" Synthetic River Water and BCR CRM 399 major elements in freshwater. The method was successfully applied to the determination of the heavy metals in tap water samples.

  5. Student Perceptions of Value Added in an Active Learning Experience: Producing, Reviewing and Evaluating a Sales Team Video Presentation

    ERIC Educational Resources Information Center

    Corbett, James J.; Kezim, Boualem; Stewart, James

    2010-01-01

    This study investigates the effectiveness of a video team-based activity as a learning experience in a sales management course. Students perceived this learning activity approach as a beneficial and effective instructional technique. The benefits of making a video in a marketing course reinforce the understanding and the use of the sales process…

  6. Identification of the key aroma compounds in cocoa powder based on molecular sensory correlations.

    PubMed

    Frauendorfer, Felix; Schieberle, Peter

    2006-07-26

    Isolation of the volatile fraction from cocoa powder (50 g; 20% fat content) by a careful extraction/distillation process followed by application of an aroma extract dilution analysis revealed 35 odor-active constituents in the flavor dilution (FD) factor range of 8-4096. Among them, 4-hydroxy-2,5-dimethyl-3(2H)-furanone (caramel-like), 2- and 3-methylbutanoic acid (sweaty, rancid), dimethyl trisulfide (cooked cabbage), 2-ethyl-3,5-dimethylpyrazine (potato-chip-like), and phenylacetaldehyde (honey-like) showed the highest FD factors. Quantitation of 31 key odorants by means of stable isotope dilution assays, followed by a calculation of their odor activity values (OAVs) (ratio of concentration to odor threshold) revealed OAVs>100 for the five odorants acetic acid (sour), 3-methylbutanal (malty), 3-methylbutanoic acid, phenylacetaldehyde, and 2-methylbutanal (malty). In addition, another 19 aroma compounds showed OAVs>1. To establish their contribution to the overall aroma of the cocoa powder, these 24 compounds were added to a reconstructed cocoa matrix in exactly the same concentrations as they occurred in the cocoa powder. The matrix was prepared from deodorized cocoa powder, which was adjusted to 20% fat content using deodorized cocoa butter. The overall sensory evaluation of this aroma recombinate versus the cocoa powder clearly indicated that the 24 compounds represented the typical sweet, cocoa-like odor of the real sample. PMID:16848541

  7. Role of hemostatic powders in the endoscopic management of gastrointestinal bleeding

    PubMed Central

    Bustamante-Balén, Marco; Plumé, Gema

    2014-01-01

    Acute gastrointestinal bleeding (AGIB) is a prevalent condition with significant influence on healthcare costs. Endoscopy is essential for the management of AGIB with a pivotal role in diagnosis, risk stratification and management. Recently, hemostatic powders have been added to our endoscopic armamentarium to treat gastrointestinal (GI) bleeding. These substances are intended to control active bleeding by delivering a powdered product over the bleeding site that forms a solid matrix with a tamponade function. Local activation of platelet aggregation and coagulation cascade may be also boosted. There are currently three powders commercially available: hemostatic agent TC-325 (Hemospray®), EndoClot™ polysaccharide hemostatic system, and Ankaferd Bloodstopper®. Although the available evidence is based on short series of cases and there is no randomized controlled trial yet, these powders seem to be effective in controlling GI bleeding from a variety of origins with a very favorable side effects profile. They can be used either as a primary therapy or a second-line treatment, and they seem to be especially indicated in cases of cancer-related bleeding and lesions with difficult access. In this review, we will comment on the mechanism of action, efficacy, safety and technical challenges of the use of powders in several clinical scenarios and we will try to define the main current indications of use and propose new lines of research in this area. PMID:25133029

  8. Value added cleaning and disinfection of the root canal: laser-activated irrigation and laser-induced photoporation

    NASA Astrophysics Data System (ADS)

    De Moor, Roeland J. G.; Meire, Maarten A.

    2016-03-01

    Among present-day marketed systems ultrasonic activation appears to be the best way to activate and potentiate endodontic irrigants. An alternative for ultrasonic activation of irrigants is laser activated irrigation (LAI) or photoninitiated acoustic streaming. Based on present-day research it appears that LAI (especially with Erbium lasers) can be more efficient for debris removal out of root canals and interaction with the endodontic biofilms thanks to the induction of specific cavitation phenomena and acoustic streaming. Other wavelengths are now explored to be used for LAI. Another way to interact with biofilms is to rely on laser-induced photoporation in combination with gold nanoparticles ( AuNPs). The latter is an alternative physical method for delivering macromolecules in cells. Nanosized membrane pores can be created upon pulsed laser illumination. Depending on the laser energy, pores are created through either direct heating of the AuNPs or by vapour nanobubbles that can emerge around the AuNPs.

  9. Lowering effect of firefly squid powder on triacylglycerol content and glucose-6-phosphate dehydrogenase activity in rat liver.

    PubMed

    Takeuchi, Hiroyuki; Morita, Ritsuko; Shirai, Yoko; Nakagawa, Yoshihisa; Terashima, Teruya; Ushikubo, Shun; Matsuo, Tatsuhiro

    2014-01-01

    Effects of dietary firefly squid on serum and liver lipid levels were investigated. Male Wistar rats were fed a diet containing 5% freeze-dried firefly squid or Japanese flying squid for 2 weeks. There was no significant difference in the liver triacylglycerol level between the control and Japanese flying squid groups, but the rats fed the firefly squid diet had a significantly lower liver triacylglycerol content than those fed the control diet. No significant difference was observed in serum triacylglycerol levels between the control and firefly squid groups. The rats fed the firefly squid had a significantly lower activity of liver glucose-6-phosphate dehydrogenase compared to the rats fed the control diet. There was no significant difference in liver fatty acid synthetase activity among the three groups. Hepatic gene expression and lipogenic enzyme activity were investigated; a DNA microarray showed that the significantly enriched gene ontology category of down-regulated genes in the firefly squid group was "lipid metabolic process". The firefly squid group had lower mRNA level of glucose-6-phosphate dehydrogenase compared to the controls. These results suggest that an intake of firefly squid decreases hepatic triacylglycerol in rats, and the reduction of mRNA level and enzyme activity of glucose-6-phosphate dehydrogenase might be related to the mechanisms.

  10. Mechanism of removal of undesirable residual amylase, insoluble starch, and select colorants from refinery streams by powdered activated carbons

    Technology Transfer Automated Retrieval System (TEKTRAN)

    There is a need in the world-wide sugar industry to find a practical and economical solution to remove or inactivate residual alpha-amylase that are high temperature stable from factory or refinery streams. A survey of refineries that used amylase and had activated carbon systems for decolorization,...

  11. Removal of Cu(II) ions by biosorption onto powdered waste sludge (PWS) prior to biological treatment in an activated sludge unit: a statistical design approach.

    PubMed

    Pamukoglu, M Yunus; Kargi, Fikret

    2009-04-01

    Biological treatment of synthetic wastewater containing Cu(II) ions was realized in an activated sludge unit with pre-adsorption of Cu(II) onto powdered waste sludge (PWS). Box-Behnken experimental design method was used to investigate Cu(II), chemical oxygen demand (COD) and toxicity removal performance of the activated sludge unit under different operating conditions. The independent variables were the solids retention time (SRT, 5-30 d), hydraulic residence time (HRT, 5-25 h), feed Cu(II) concentration (0-50 mg L(-1)) and PWS loading rate (0-4 g h(-1)) while percent Cu(II), COD, toxicity (TOX) removals and the sludge volume index (SVI) were the objective functions. The data were correlated with a quadratic response function (R2=0.99). Cu(II), COD and toxicity removals increased with increasing PWS loading rate and SRT while decreasing with the increasing feed Cu(II) concentration and HRT. Optimum conditions resulting in maximum Cu(II), COD, toxicity removals and SVI values were found to be SRT of 30 d, HRT 15 h, PWS loading rate 3 g h(-1) and feed Cu(II) concentration of less than 30 mg L(-1).

  12. Influence of pH on the formulation of TiO2 powder prepared by co-precipitation of TiCl3 and photocatalytic activity

    NASA Astrophysics Data System (ADS)

    Yudoyono, Gatut; Zharvan, Vicran; Ichzan, Nur; Daniyati, Rizqa; Indarto, Bachtera; Pramono, Yono Hadi; Zainuri, Mochamad; Darminto

    2016-02-01

    Titanium dioxide (titania) nanoparticle were synthesized by coprecipitation process of titanium trichloride (TiCl3) in aqueous medium, with NH4OH as pH regulator. The pH solution was varied during the synthesis process between pH 3-8.4, and all samples were calcined temperature at 400°C for 3 hours. Characteristics and properties of the TiO2 powder were investigated using X-ray diffraction (XRD), Scanning Electron Microscopy (SEM). XRD results show that the single-phase rutile formed when the pH is less than 5, anatase single phase formed began pH 8, and the pH of the solution between 5-8 formed mixed phase rutile-anatase-brookite, rutile-brookite or anatase-brookite. Methylene Blue (MB) photodegradation test were performed in order to evaluate photocatalytic activity. Nanoparticles TiO2 rutile, anatase phase, and mixed phase rutile-brookite, anatase-brookite used to test the photocatalytic activity by measuring the absorbance spectrum photodegradation using UV-Vis spectrometer. The test results showed that the mixture phase of rutile-brookite provide the greatest photodegradation than other phases.

  13. A comparative study of coagulation, granular- and powdered-activated carbon for the removal of perfluorooctane sulfonate and perfluorooctanoate in drinking water treatment.

    PubMed

    Pramanik, Biplob Kumar; Pramanik, Sagor Kumar; Suja, Fatihah

    2015-01-01

    Perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are persistent organic pollutants in the environment and their occurrence causes toxicological effects on humans. We examined different conventional coagulant treatments such as alum, ferric chloride and polyaluminium chloride in removing these compounds. These were then compared with a natural coagulant (Moringa oleifera). We also investigated the powdered-activated carbon (PAC) and granular-activated carbon (GAC) for removing these compounds. At an initial dose of 5 mg/L, polyaluminium chloride led to a higher reduction of PFOS/PFOA compared with alum which in turn was higher than ferric. The removal efficiency increased with the increase in coagulant dose and decrease in pH. M. oleifera was very effective in reducing PFOS and PFOA than conventional coagulants, with a reduction efficiencies of 65% and 72%, respectively, at a dose of 30 mg/L. Both PAC and GAC were very effective in reducing these compounds than coagulations. PAC led to a higher reduction in PFOS and PFOA than GAC due to its greater surface area and shorter internal diffusion distances. The addition of PAC (10 min contact time) with coagulation (at 5 mg/L dosage) significantly increased the removal efficiency, and the maximum removal efficiency was for M. oleifera with 98% and 94% for PFOS and PFOA, respectively. The reduction efficiency of PFOS/PFOA was reduced with the increase in dissolved organic concentration due to the adsorption competition between organic molecules and PFOS/PFOA. PMID:25860623

  14. UV254 absorbance as real-time monitoring and control parameter for micropollutant removal in advanced wastewater treatment with powdered activated carbon.

    PubMed

    Altmann, Johannes; Massa, Lukas; Sperlich, Alexander; Gnirss, Regina; Jekel, Martin

    2016-05-01

    This study investigates the applicability of UV absorbance measurements at 254 nm (UVA254) to serve as a simple and reliable surrogate parameter to monitor and control the removal of organic micropollutants (OMPs) in advanced wastewater treatment applying powdered activated carbon (PAC). Correlations between OMP removal and corresponding UVA254 reduction were determined in lab-scale adsorption batch tests and successfully applied to a pilot-scale PAC treatment stage to predict OMP removals in aggregate samples with good accuracy. Real-time UVA254 measurements were utilized to evaluate adapted PAC dosing strategies and proved to be effective for online monitoring of OMP removal. Furthermore, active PAC dosing control according to differential UVA254 measurements was implemented and tested. While precise removal predictions based on real-time measurements were not accurate for all OMPs, UVA254-controlled dynamic PAC dosing was capable of achieving stable OMP removals. UVA254 can serve as an effective surrogate parameter for OMP removal in technical PAC applications. Even though the applicability as control parameter to adjust PAC dosing to water quality changes might be limited to applications with fast response between PAC adjustment and adsorptive removal (e.g. direct filtration), UVA254 measurements can also be used to monitor the adsorption efficiency in more complex PAC applications. PMID:26963606

  15. A comparative study of coagulation, granular- and powdered-activated carbon for the removal of perfluorooctane sulfonate and perfluorooctanoate in drinking water treatment.

    PubMed

    Pramanik, Biplob Kumar; Pramanik, Sagor Kumar; Suja, Fatihah

    2015-01-01

    Perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are persistent organic pollutants in the environment and their occurrence causes toxicological effects on humans. We examined different conventional coagulant treatments such as alum, ferric chloride and polyaluminium chloride in removing these compounds. These were then compared with a natural coagulant (Moringa oleifera). We also investigated the powdered-activated carbon (PAC) and granular-activated carbon (GAC) for removing these compounds. At an initial dose of 5 mg/L, polyaluminium chloride led to a higher reduction of PFOS/PFOA compared with alum which in turn was higher than ferric. The removal efficiency increased with the increase in coagulant dose and decrease in pH. M. oleifera was very effective in reducing PFOS and PFOA than conventional coagulants, with a reduction efficiencies of 65% and 72%, respectively, at a dose of 30 mg/L. Both PAC and GAC were very effective in reducing these compounds than coagulations. PAC led to a higher reduction in PFOS and PFOA than GAC due to its greater surface area and shorter internal diffusion distances. The addition of PAC (10 min contact time) with coagulation (at 5 mg/L dosage) significantly increased the removal efficiency, and the maximum removal efficiency was for M. oleifera with 98% and 94% for PFOS and PFOA, respectively. The reduction efficiency of PFOS/PFOA was reduced with the increase in dissolved organic concentration due to the adsorption competition between organic molecules and PFOS/PFOA.

  16. 21 CFR 520.44 - Acetazolamide sodium soluble powder.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acetazolamide sodium soluble powder. 520.44... Acetazolamide sodium soluble powder. (a) Specifications. The drug is in a powder form containing acetazolamide sodium, USP equivalent to 25 percent acetazolamide activity. (b) Sponsor. See No. 053501 in §...

  17. 21 CFR 520.44 - Acetazolamide sodium soluble powder.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Acetazolamide sodium soluble powder. 520.44... Acetazolamide sodium soluble powder. (a) Specifications. The drug is in a powder form containing acetazolamide sodium, USP equivalent to 25 percent acetazolamide activity. (b) Sponsor. See No. 053501 in §...

  18. Photocatalytic activity of nanostructured {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} composite powder formed via a polyelectrolyte-multilayer-assisted sol-gel reaction

    SciTech Connect

    Logar, Manca; Kocjan, Andraz; Dakskobler, Ales

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer PEM assisted synthesis for {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} composite powder is developed. Black-Right-Pointing-Pointer Nanoparticulate TiO{sub 2} layer results in high specific surface area composite powder. Black-Right-Pointing-Pointer {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} composite powder exhibit enhanced photocatalytic activity. -- Abstract: Nanostructured, {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} composite powder was fabricated via an in situ, sol-gel reaction of titanium iso-propoxide in a self-assembled, polyelectrolyte multilayer (PEM) formed on the surface of high-specific-area, polycrystalline, {gamma}-Al{sub 2}O{sub 3} lamellas. The infiltration of the titanium precursor into the PEM, followed by the hydrolysis and condensation reactions with the water absorbed in the PEM after annealing, resulted in the formation of a nanostructured TiO{sub 2} layer on the surface of the {gamma}-Al{sub 2}O{sub 3} lamellas. Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) were employed to evaluate the morphology, the chemical composition and the crystallinity of the {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} particles of the composite powder. The as-formed, nanostructured, {gamma}-Al{sub 2}O{sub 3}/TiO{sub 2} composite powder exhibited a 2.7-times-higher photo-activity in the near-UV region compared to commercially available TiO{sub 2} (Degusa P25), as monitored by the photo-decomposition of a methylene blue (MB) dye.

  19. The reduction of graphene oxide by zinc powder to produce a zinc oxide-reduced graphene oxide hybrid and its superior photocatalytic activity

    NASA Astrophysics Data System (ADS)

    Sarkar, Sanjit; Basak, Durga

    2013-03-01

    We have synthesized for the first time ZnO/rGO hybrids from metal zinc and GO using hydrothermal technique without adding further reducing agent. The photocatalytic property of ZnO-rGO reveals that the hybrid for 50 mg of GO has the highest activity, causing a 94% degradation of methyl orange compared to 70% by only ZnO. The consistent quenching and a gradual decrease in the decay life time of the emission at ˜500 nm as the rGO content increases indicates the interfacial charge transfer process between ZnO and rGO by the defect states responsible for green emission.

  20. Multiple feed powder splitter

    SciTech Connect

    Lewis, Gary K.; Less, Richard M.

    2002-01-01

    A device for providing uniform powder flow to the nozzles when creating solid structures using a solid fabrication system such as the directed light fabrication (DLF) process. In the DLF process, gas entrained powders are passed through the focal point of a moving high-power laser light which fuses the particles in the powder to a surface being built up in layers. The invention is a device providing uniform flow of gas entrained powders to the nozzles of the DLF system. The device comprises a series of modular splitters which are slidably interconnected and contain an integral flow control mechanism. The device can take the gas entrained powder from between one to four hoppers and split the flow into eight tubular lines which feed the powder delivery nozzles of the DLF system.

  1. Multiple feed powder splitter

    SciTech Connect

    Lewis, Gary K.; Less, Richard M.

    2001-01-01

    A device for providing uniform powder flow to the nozzles when creating solid structures using a solid fabrication system such as the directed light fabrication (DLF) process. In the DLF process, gas entrained powders are passed through the focal point of a moving high-power laser light which fuses the particles in the powder to a surface being built up in layers. The invention is a device providing uniform flow of gas entrained powders to the nozzles of the DLF system. The device comprises a series of modular splitters which are slidably interconnected and contain an integral flow control mechanism. The device can take the gas entrained powder from between one to four hoppers and split the flow into eight tubular lines which feed the powder delivery nozzles of the DLF system.

  2. Granulation of fine powder

    DOEpatents

    Chen, Ching-Fong

    2016-08-09

    A mixture of fine powder including thorium oxide was converted to granulated powder by forming a first-green-body and heat treating the first-green-body at a high temperature to strengthen the first-green-body followed by granulation by crushing or milling the heat-treated first-green-body. The granulated powder was achieved by screening through a combination of sieves to achieve the desired granule size distribution. The granulated powder relies on the thermal bonding to maintain its shape and structure. The granulated powder contains no organic binder and can be stored in a radioactive or other extreme environment. The granulated powder was pressed and sintered to form a dense compact with a higher density and more uniform pore size distribution.

  3. Pretreatment of garlic powder using sweep frequency ultrasound and single frequency countercurrent ultrasound: optimization and comparison for ACE inhibitory activities.

    PubMed

    Ma, Haile; Huang, Liurong; Peng, Lei; Wang, Zhenbin; Yang, Qiaorong

    2015-03-01

    The sweep frequency ultrasound (SFU) and single frequency countercurrent ultrasound (SFCU) pretreatments were modeled and compared based on production of angiotensin I-converting enzyme (ACE) inhibitory peptides from garlic hydrolysates. Two mathematical models were developed to show the effect of each variable and their combinatorial interactions on ACE inhibitory activity. The optimum levels of the parameters in SFU were determined using uniform design, which revealed these as follows: total ultrasonic time 1.5 h, on-time of pulse 18 s and off-time of pulse 3 s. Under optimized conditions, the experimental values of SFU and SFCU were 65.88% and 67.78%, which agreed closely with the predicted values of 63.44% and 67.33%. The SFU and SFCU pretreatments both resulted in higher ACE inhibitory activity compared with untreated garlic (p<0.05). However, there were no significant differences in the ACE inhibitory activities and IC₅₀ values obtained from SFCU and SFU pretreatments under optimum conditions (p>0.05).

  4. The Effect of Crystallinity of Carbon Source on Mechanically Activated Carbothermic Synthesis of Nano-Sized SiC Powders

    NASA Astrophysics Data System (ADS)

    Moshtaghioun, B. M.; Monshi, A.; Abbasi, M. H.; Karimzadeh, F.

    2013-02-01

    The relevance of the structure of carbon materials and milling on the carbothermic reduction of silica to produce nano-sized silicon carbide (SiC) was studied. Graphite (crystalline) and metallurgical coke (mainly amorphous) were chosen as carbon precursors that were mixed with amorphous pure nano-sized SiO2 and milled for different times. The SiC yield at 1450 °C for l h was influenced by the degree of milling. Extending the milling time increased SiC formation in both cases. Although some extensive milling converted both sources of carbon into amorphous phase, the amount of synthesized SiC from graphite was about 4.5-3 times higher than coke with increased extent of milling. Graphite is converted from stable crystalline state into the amorphous phase, so it absorbs more activation energy of milling and fresher active centers are created, while the already amorphous coke absorbs less energy and thus less fresh active centers are created. This energy difference acts as a driving force, resulting in higher yield of nano-sized SiC when graphite is used as carbon source.

  5. Effects of BOSU ball(s) during sit-ups with body weight and added resistance on core muscle activation.

    PubMed

    Saeterbakken, Atle H; Andersen, Vidar; Jansson, June; Kvellestad, Ann C; Fimland, Marius S

    2014-12-01

    The objective of this study was to assess the electromyographic activity of the rectus abdominis (upper and lower part) and external oblique during sit-ups performed on BOSU ball(s). Twenty-four men participated in a familiarization session, and in the next session, they performed the experimental tests in randomized order. The sit-ups were performed with 10 repetitions with body weight and with 10 repetition maximum (10RM) using elastic bands as external resistance under 4 different conditions: (a) on a stable surface, (b) with the BOSU ball under their feet (dome side down, lower-body instability), (c) BOSU ball under the low back (dome side up, upper-body instability), and (d) with BOSU balls under both feet and the low back (dual instability). The feet were not attached to the surface. We observed that with body weight, external oblique activation was decreased by upper-body instability and dual instability by 22-24% (p = 0.002-0.006), whereas the rectus abdominis was not affected by the surface. Using 10RM loads, the upper and lower rectus abdominis activities were increased by upper body and dual instability by 21-24% compared with that for a stable surface (P ≤ 0.001-0.036). Further, lower-body instability did not affect muscle activities significantly with either load for any condition. Hence, BOSU balls under the low back can increase and decrease abdominal muscle activation depending on the load, whereas placing a BOSU ball under the feet with the dome side down had little impact.

  6. Storage stability of phenolic compounds in powdered BRS Violeta grape juice microencapsulated with protein and maltodextrin blends.

    PubMed

    Moser, Poliana; Telis, Vânia Regina Nicoletti; de Andrade Neves, Nathália; García-Romero, Esteban; Gómez-Alonso, Sergio; Hermosín-Gutiérrez, Isidro

    2017-01-01

    The stabilities of the phenolic compounds, antioxidant activity and colour parameters of microencapsulated powdered BRS Violeta red grape juice were evaluated throughout storage at 5, 25 and 35°C for up to 150days. Different soy protein (S) or whey protein (W) blends with maltodextrin (M) were used as carrier agents, added at diverse concentrations and proportions. The treatment combining S and M with the highest carrier agent concentration (1SM) preserved almost all the anthocyanins. Except for 1SM, the proportion of p-coumaroylated anthocyanins increased during storage, and the flavonol content of the 1SM powder decreased after 150days. The hydroxycinnamate content decreased for all treatments, independent of storage temperature, and flavan-3-ols were lost at 35°C. The time and temperature did not influence the antioxidant activity of the powder or the colour of the reconstituted grape juice after 150days.

  7. Storage stability of phenolic compounds in powdered BRS Violeta grape juice microencapsulated with protein and maltodextrin blends.

    PubMed

    Moser, Poliana; Telis, Vânia Regina Nicoletti; de Andrade Neves, Nathália; García-Romero, Esteban; Gómez-Alonso, Sergio; Hermosín-Gutiérrez, Isidro

    2017-01-01

    The stabilities of the phenolic compounds, antioxidant activity and colour parameters of microencapsulated powdered BRS Violeta red grape juice were evaluated throughout storage at 5, 25 and 35°C for up to 150days. Different soy protein (S) or whey protein (W) blends with maltodextrin (M) were used as carrier agents, added at diverse concentrations and proportions. The treatment combining S and M with the highest carrier agent concentration (1SM) preserved almost all the anthocyanins. Except for 1SM, the proportion of p-coumaroylated anthocyanins increased during storage, and the flavonol content of the 1SM powder decreased after 150days. The hydroxycinnamate content decreased for all treatments, independent of storage temperature, and flavan-3-ols were lost at 35°C. The time and temperature did not influence the antioxidant activity of the powder or the colour of the reconstituted grape juice after 150days. PMID:27507480

  8. Cow dung powder poisoning.

    PubMed

    Sherfudeen, Khaja Mohideen; Kaliannan, Senthil Kumar; Dammalapati, Pavan Kumar

    2015-11-01

    Cow dung, which has germicidal property, was used in ancient days to clean living premises in South India. Nowadays, people are using commercially available synthetic cow dung powder. It is locally known as "saani powder" in Tamil Nadu. It is freely available in homes and is sometimes accidentally consumed by children. It is available in two colors - yellow and green. Cow dung powder poisoning is common in districts of Tamil Nadu such as Coimbatore, Tirupur, and Erode. We report two cases of yellow cow dung powder poisoning from our hospital. PMID:26730123

  9. Dietary grape powder increases IL-1β and IL-6 production by lipopolysaccharide-activated monocytes and reduces plasma concentrations of large LDL and large LDL-cholesterol particles in obese humans.

    PubMed

    Zunino, Susan J; Peerson, Jan M; Freytag, Tammy L; Breksa, Andrew P; Bonnel, Ellen L; Woodhouse, Leslie R; Storms, David H

    2014-08-14

    Obese individuals are at an increased risk of developing CVD, hypertension, type 2 diabetes, and bacterial and viral infections when compared with the normal-weight population. In a 9-week randomised, double-blind, cross-over study, twenty-four obese subjects aged between 20 and 60 years and with a BMI between 30 and 45 kg/m2 were fed grape or placebo powder for 3-week intervals to determine the effects of dietary grapes on blood lipid profiles, plasma inflammatory marker concentrations and immune cell function. Blood samples were collected on days 1 and 8 for obtaining baseline information and at weeks 3, 4, 8 and 9. Comprehensive chemistry panels, lipid profile analyses by NMR, measurement of plasma inflammatory marker concentrations, and analyses of cytokine production by activated T lymphocytes and monocytes were performed for each blood draw. Dietary grape powder reduced the plasma concentrations of large LDL-cholesterol and large LDL particles compared with the placebo powder (P< 0·05). The concentrations of interferon-γ, TNF-α, IL-4 and IL-10 were measured in supernatants from peripheral blood mononuclear cells (PBMC) activated with anti-CD3/CD28 antibodies and those of TNF-α, IL-1β, IL-6 and IL-8 were measured in supernatants from PBMC activated with lipopolysaccharide (LPS). No difference in the production of T-cell cytokines was observed between the two intervention groups. The production of IL-1β and IL-6 was increased in supernatants from LPS-activated PBMC in the grape powder group compared with the placebo powder group (P< 0·05). These data suggest that dietary grapes may decrease atherogenic lipid fractions in obese individuals and increase the sensitivity of monocytes in a population at a greater risk of developing infections.

  10. Simultaneous determination of cation exchange capacity and surface area of acid activated bentonite powders by methylene blue sorption

    NASA Astrophysics Data System (ADS)

    Yener, Nilgün; Biçer, Cengiz; Önal, Müşerref; Sarıkaya, Yüksel

    2012-01-01

    To distinguish the ion exchanged and physically adsorbed methylene blue cations (MB+) on ionic surfaces, acid activated bentonite samples were used as porous adsorbents. A natural calcium bentonite (CaB) sample from Enez/Edirne, Turkey, was acid activated at 90 °C for 16 h with various HCl/CaB ratios. The irreversible exchange and physical adsorption of MB+ cations on the ionic solids have simultaneously occurred. The ion exchanged (mex) and physically adsorbed (mad) MB+ contents were obtained as the values of sorption capacity at c = 0 and the increase to a plateaus of adsorption isotherms, respectively. The mad value was taken to be monolayer adsorption capacity. Cation exchange capacity (CEC) and specific surface area (SMB) for each sample were calculated from the mex and mad values, respectively. Also, the BET specific surface areas (SBET) and pore size distribution were determined from low temperature nitrogen adsorption/desorption data. A linear correlation between the SMB and SBET values was found.

  11. Microemulsion Synthesis of Nanoparticle PZT Powder

    NASA Astrophysics Data System (ADS)

    Amiriyan, M.; Nemati, Z. A.; Rahmanifar, M. S.; Ramesh, S.; Meenaloshini, S.; Tolouei, R.

    2011-01-01

    Nanocrystalline lead zirconate titanate (PZT) powders have been synthesized using microemulsion processing route. Microemulsion is one of the major processing techniques to synthesize a nanosize, homogenous, and almost agglomerate free ceramic powders. The ternary microemulsion system is consisted of cyclohexane as the oil phase, Triton X100 as the nonionic surfactant phase, and an aqueous phase containing 0.619 M Pb2+, 0.325 M Zr4+, and 0.3 M Ti4+, representing a Pb2+: Zr4+: Ti4+ molar ratio of 1:0.52:0.48. The ratio of these cations has been adjusted using Inductively Coupled Plasma (ICP) technique. After coprecipitation of metallic hydroxides by adding ammonia solution in microemulsion system, the PZT precursor was obtained. PZT powders have been prepared upon calcination of precursor at 800° C. Prepared powders was characterised using techniques such as X-ray diffraction, differential thermal analysis, and scanning electron microscopy. The characteristics of microemulsion processed powder is discussed, with emphasis on the presence of nano scaled PZT powder with a composition near to morphotropic phase boundary (MPB) without formation of any intermediate phases.

  12. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-05

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of ternary mixtures consisting of: Ni powder, Cu powder, and Al powder, Ni powder, Cr powder, and Al powder; Ni powder, W powder and Al powder; Ni powder, V powder, and Al powder; Ni powder, Mo powder, and Al powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  13. Desensitizing nano powders to electrostatic discharge ignition

    SciTech Connect

    Steelman, Ryan; Clark, Billy; Pantoya, Michelle L.; Heaps, Ronald J.; Daniels, Michael A.

    2015-08-01

    Electrostatic discharge (ESD) is a main cause for ignition in powder media ranging from grain silos to fireworks. Nanoscale particles are orders of magnitude more ESD ignition sensitive than their micron scale counterparts. This study shows that at least 13 vol. % carbon nanotubes (CNT) added to nano-aluminum and nano-copper oxide particles (nAl + CuO) eliminates ESD ignition sensitivity. The CNT act as a conduit for electric energy and directs electric charge through the powder to desensitize the reactive mixture to ignition. For nanoparticles, the required CNT concentration for desensitizing ESD ignition acts as a diluent to quench energy propagation.

  14. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1995-12-26

    A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figs.

  15. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1994-01-01

    A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

  16. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1995-01-01

    A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

  17. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1994-12-06

    A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figures.

  18. CVD boron on calcium chromate powder

    SciTech Connect

    Coonen, R.M.

    1984-09-01

    This study was an experimental effort to improve the compositional homogeneity of a pyrotechnic mixture of boron and calcium chromate (CaCrO/sub 4/). Boron was deposited onto calcium chromate powders at 350/sup 0/C from a diborane and hydrogen gas mixture at a pressure of 40 torr by Chemical Vapor Deposition (CVD). The B:CaCrO/sub 4/ ratio of the coated powders was analyzed by inductively-coupled plasma spectroscopy and the distribution of the two phases was observed by electron microprobe analysis. The pyrotechnic activity was determined by differential thermal analysis. In addition to varying the composition of the mixture, an attempt was made to vary the boron distribution by coating both sized and unsized CaCrO/sub 4/ powders. Boron was deposited for 2 h onto sized CaCrO/sub 4/ powder, which resulted in a higher weight percentage of boron in comparison to the unsized powder. CVD coated CaCrO/sub 4/ powders began their pyrotechnic activity at an auto ignition temperature that was lower than the auto ignition temperature observed for mechanically blended mixtures. The coating of sized CaCrO/sub 4/ powder improved the uniformity of boron deposition of CaCrO/sub 4/, but it also decreased the pyrotechnic activity.

  19. Segmented strings in AdS 3

    NASA Astrophysics Data System (ADS)

    Callebaut, Nele; Gubser, Steven S.; Samberg, Andreas; Toldo, Chiara

    2015-11-01

    We study segmented strings in flat space and in AdS 3. In flat space, these well known classical motions describe strings which at any instant of time are piecewise linear. In AdS 3, the worldsheet is composed of faces each of which is a region bounded by null geodesics in an AdS 2 subspace of AdS 3. The time evolution can be described by specifying the null geodesic motion of kinks in the string at which two segments are joined. The outcome of collisions of kinks on the worldsheet can be worked out essentially using considerations of causality. We study several examples of closed segmented strings in AdS 3 and find an unexpected quasi-periodic behavior. We also work out a WKB analysis of quantum states of yo-yo strings in AdS 5 and find a logarithmic term reminiscent of the logarithmic twist of string states on the leading Regge trajectory.

  20. Polarised black holes in AdS

    NASA Astrophysics Data System (ADS)

    Costa, Miguel S.; Greenspan, Lauren; Oliveira, Miguel; Penedones, João; Santos, Jorge E.

    2016-06-01

    We consider solutions in Einstein-Maxwell theory with a negative cosmological constant that asymptote to global AdS 4 with conformal boundary {S}2× {{{R}}}t. At the sphere at infinity we turn on a space-dependent electrostatic potential, which does not destroy the asymptotic AdS behaviour. For simplicity we focus on the case of a dipolar electrostatic potential. We find two new geometries: (i) an AdS soliton that includes the full backreaction of the electric field on the AdS geometry; (ii) a polarised neutral black hole that is deformed by the electric field, accumulating opposite charges in each hemisphere. For both geometries we study boundary data such as the charge density and the stress tensor. For the black hole we also study the horizon charge density and area, and further verify a Smarr formula. Then we consider this system at finite temperature and compute the Gibbs free energy for both AdS soliton and black hole phases. The corresponding phase diagram generalizes the Hawking-Page phase transition. The AdS soliton dominates the low temperature phase and the black hole the high temperature phase, with a critical temperature that decreases as the external electric field increases. Finally, we consider the simple case of a free charged scalar field on {S}2× {{{R}}}t with conformal coupling. For a field in the SU(N ) adjoint representation we compare the phase diagram with the above gravitational system.

  1. Relative survival of four serotypes of Salmonella enterica in low-water activity whey protein powder held at 36 and 70°C at various water activity levels.

    PubMed

    Farakos, S M Santillana; Hicks, J W; Frye, J G; Frank, J F

    2014-07-01

    Salmonella enterica is not able to grow at water activity (aw) levels below 0.94, but it can survive in low-aw foods for long periods of time. Temperature, aw, substrate, and serotype affect its persistence. The aim of this study was to evaluate the influence of temperature and aw on the relative persistence among four serotypes of Salmonella enterica in low-aw whey protein powder. Whey protein powder was equilibrated to aws 0.18 ± 0.02 and 0.54 ± 0.03, inoculated with a cocktail of Salmonella serovars (Agona, Tennessee, Montevideo, and Typhimurium), vacuum sealed, and stored at 36°C for 6 months and at 70°C for 48 h. Presumptive Salmonella colonies (30 to 32) were randomly picked from each plate at the end of each survival study. PCR multiplex serotyping was used to identify the isolates. A multinomial mixed logistic model with Salmonella Tennessee as a reference was used to test for significant differences in frequency distribution of the surviving serotypes. Salmonella Tennessee and Salmonella Agona were the most prevalent surviving serotypes, followed in decreasing order by Salmonella Montevideo and Salmonella Typhimurium. Statistical analysis indicated that temperature (P = 0.003) and aw (P = 0.012) influenced the relative prevalence of the Salmonella serotypes. If other environmental conditions are equal, Salmonella Tennessee is better able to survive than Salmonella Montevideo and Salmonella Typhimurium at higher temperatures and higher aw levels in low-aw whey protein powder held at 36 and 70°C. The relative prevalence of Salmonella Agona to Salmonella Tennessee did not change with increasing temperature (P = 0.211) or aw (P = 0.453). These results should be considered in risk assessment and when developing predictive models for survival of Salmonella in low-aw foods. PMID:24988029

  2. Study of the adsorption of Cr(VI) by tannic acid immobilised powdered activated carbon from micro-polluted water in the presence of dissolved humic acid.

    PubMed

    Gong, Xujin; Li, Weiguang; Wang, Ke; Hu, Jinhua

    2013-08-01

    The adsorption of Cr(VI) (0.500 mg/L) onto food-grade tannic-acid immobilised powdered activated carbon (TA-PAC) in the presence of dissolved humic acid (DHA) was investigated at 280 K as a function of pH, along with the adsorption capacities and the adsorption isotherms for chromium ions. The results showed that the presence of DHA improved the adsorption capacities of Cr(VI) and its reduction product (Cr(III)) over a wide pH range (4.0-8.0). The main mechanism for metal-DHA complexation in the Cr(VI) system was the reduction of Cr(VI) followed by complexation between Cr(III) and DHA. The Freundlich isotherms yielded the best fits to all data (R(2)=0.9951, qm=5.639 mg/g) in the presence of DHA. The adsorption mechanisms of Cr(VI) onto TA-PAC in the presence of DHA were summarized into three categories: (i) binding by anion adsorption, (ii) Cr(VI) reduction followed by Cr(III) adsorption, and (iii) adsorption of Cr(III)-DHA complexes.

  3. Promoting the bio-cathode formation of a constructed wetland-microbial fuel cell by using powder activated carbon modified alum sludge in anode chamber.

    PubMed

    Xu, Lei; Zhao, Yaqian; Doherty, Liam; Hu, Yuansheng; Hao, Xiaodi

    2016-01-01

    MFC centered hybrid technologies have attracted attention during the last few years due to their compatibility and dual advantages of energy recovery and wastewater treatment. In this study, a MFC was integrated into a dewatered alum sludge (DAS)- based vertical upflow constructed wetland (CW). Powder activate carbon (PAC) was used in the anode area in varied percentage with DAS to explore its influences on the performance of the CW-MFC system. The trial has demonstrated that the inclusion of PAC improved the removal efficiencies of COD, TN and RP. More significantly, increasing the proportion of PAC from 2% to 10% can significantly enhance the maximum power densities from 36.58 mW/m(2) to 87.79 mW/m(2). The induced favorable environment for bio-cathode formation might be the main reason for this improvement since the content of total extracellular polymeric substances (TEPS) of the substrate in the cathode area almost doubled (from 44.59 μg/g wet sludge to 87.70 μg/g wet sludge) as the percentage of PAC increased to 10%. This work provides another potential usage of PAC in CW-MFCs with a higher wastewater treatment efficiency and energy recovery. PMID:27197845

  4. Powdered activated carbon coupled with enhanced coagulation for natural organic matter removal and disinfection by-product control: application in a Western Australian water treatment plant.

    PubMed

    Kristiana, Ina; Joll, Cynthia; Heitz, Anna

    2011-04-01

    The removal of organic precursors of disinfection by-products (DBPs), i.e. natural organic matter (NOM), prior to disinfection and distribution is considered as the most effective approach to minimise the formation of DBPs. This study investigated the impact of the addition of powdered activated carbon (PAC) to an enhanced coagulation treatment process at an existing water treatment plant on the efficiency of NOM removal, the disinfection behaviour of the treated water, and the water quality in the distribution system. This is the first comprehensive assessment of the efficacy of plant-scale application of PAC combined with enhanced coagulation on an Australian source water. As a result of the PAC addition, the removal of NOM improved by 70%, which led to a significant reduction (80-95%) in the formation of DBPs. The water quality in the distribution system also improved, indicated by lower concentrations of DBPs in the distribution system and better maintenance of disinfectant residual at the extremities of the distribution system. The efficacy of the PAC treatment for NOM removal was shown to be a function of the characteristics of the NOM and the quality of the source water, as well as the PAC dose. PAC treatment did not have the capacity to remove bromide ion, resulting in the formation of more brominated DBPs. Since brominated DBPs have been found to be more toxic than their chlorinated analogues, their preferential formation upon PAC addition must be considered, especially in source waters containing high concentrations of bromide. PMID:21353285

  5. Promoting the bio-cathode formation of a constructed wetland-microbial fuel cell by using powder activated carbon modified alum sludge in anode chamber

    NASA Astrophysics Data System (ADS)

    Xu, Lei; Zhao, Yaqian; Doherty, Liam; Hu, Yuansheng; Hao, Xiaodi

    2016-05-01

    MFC centered hybrid technologies have attracted attention during the last few years due to their compatibility and dual advantages of energy recovery and wastewater treatment. In this study, a MFC was integrated into a dewatered alum sludge (DAS)- based vertical upflow constructed wetland (CW). Powder activate carbon (PAC) was used in the anode area in varied percentage with DAS to explore its influences on the performance of the CW-MFC system. The trial has demonstrated that the inclusion of PAC improved the removal efficiencies of COD, TN and RP. More significantly, increasing the proportion of PAC from 2% to 10% can significantly enhance the maximum power densities from 36.58 mW/m2 to 87.79 mW/m2. The induced favorable environment for bio-cathode formation might be the main reason for this improvement since the content of total extracellular polymeric substances (TEPS) of the substrate in the cathode area almost doubled (from 44.59 μg/g wet sludge to 87.70 μg/g wet sludge) as the percentage of PAC increased to 10%. This work provides another potential usage of PAC in CW-MFCs with a higher wastewater treatment efficiency and energy recovery.

  6. Powdered activated carbon adsorption of two fishy odorants in water: Trans,trans-2,4-heptadienal and trans,trans-2,4-decadienal.

    PubMed

    Li, Xin; Wang, Jun; Zhang, Xiaojian; Chen, Chao

    2015-06-01

    Powdered activated carbon (PAC) adsorption of two fishy odorants, trans,trans-2,4-heptadienal (HDE) and trans,trans-2,4-decadienal (DDE), was investigated. Both the pseudo first-order and the pseudo second-order kinetic models well described the kinetics curves, and DDE was more readily removed by PAC. In isotherm tests, both Freundlich and Modified Freundlich isotherms fitted the experimental data well. PAC exhibited a higher adsorption capacity for DDE than for HDE, which could be ascribed to the difference in their hydrophobicity. The calculated thermodynamic parameters (ΔG0, ΔH0, and ΔS0) indicated an exothermic and spontaneous adsorption process. PAC dosage, pH, and natural organic matter (NOM) presence were found to influence the adsorption process. With increasing PAC dosage, the pseudo first-order and pseudo second-order rate constants both increased. The value of pH had little influence on HDE or DDE molecules but altered the surface charge of PAC, and the maximum adsorption capacity occurred at pH9. The presence of NOM, especially the fraction with molecular weight less than 1k Dalton, hindered the adsorption. The study showed that preloaded NOM impaired the adsorption capacity of HDE or DDE more severely than simultaneously fed NOM did.

  7. Facile preparation of magnetic separable powdered-activated-carbon/Ni adsorbent and its application in removal of perfluorooctane sulfonate (PFOS) from aqueous solution.

    PubMed

    Liang, Xuanqi; Gondal, Mohammed A; Chang, Xiaofeng; Yamani, Zain H; Li, Nianwu; Lu, Hongling; Ji, Guangbin

    2011-01-01

    The main aim of this study was to synthesize magnetic separable Nickel/powdered activated carbon (Ni/PAC) and its application as an adsorbent for removal of PFOS from aqueous solution. In this work, the synthesized adsorbent using simple method was characterized by using X-ray diffractionometer (XRD), surface area and pore size analyzer, vibrating sample magnetometer (VSM), and high resolution transmission electron microscope (HRTEM). The surface area, pore volume and pore size of synthesized PAC was 1521.8 m(2)g(-1), 0.96 cm(3)g(-1), 2.54 nm, respectively. Different kinetic models: the pseudo-first-order model, the pseudo-second-order model, and three adsorption isotherms--Langmuir, Freundlich and Temkin--were applied to study the sorption kinetics and isothermal behavior of PFOS onto the surface of an as-prepared adsorbent. The rate constant using the pseudo-second-order model for removal of 150 ppm PFOS was estimated as 8.82×10(-5) and 1.64×10(-4) for PAC and 40% Ni/PAC, respectively. Our results demonstrated that the composite adsorbents exhibited a clear magnetic hysteretic behavior, indicating the potential practical application in magnetic separation of adsorbents from aqueous solution phase as well. PMID:21961696

  8. Removal of Cr(VI) from low-temperature micro-polluted surface water by tannic acid immobilized powdered activated carbon.

    PubMed

    Li, Weiguang; Gong, Xujin; Li, Xin; Zhang, Duoying; Gong, Hainan

    2012-06-01

    In this study, food-grade tannic acid-immobilized powdered activated carbon (TA-PAC) was prepared, and adsorption of Cr(VI) (0.500 mg/L) onto TA-PAC as a function of pH, contact time, adsorption capacities and adsorption isotherms at 280 K was investigated. The results indicated that the immobilization process introduced abundant acid functional groups. The adsorption capacity of TA-PAC was found to be pH-dependent, and the optimal pH value was found to be 4.0. The equilibrium time was 240 min for TA-PAC. Adsorption data for total chromium were modeled using both two-parameter and three-parameter isotherm models. Freundlich and linear forms of three-parameter models yielded the best results for all of the data. Desorption studies of immobilized material suggested that the immobilization of food-grade tannic acid is steady. The adsorption mechanism of Cr(VI) on TA-PAC was assumed to be a comprehensive process consisting of surface reduction of Cr(VI), esterification between catechol and chromate, and ion exchange. PMID:22243926

  9. Study of the adsorption of Cr(VI) by tannic acid immobilised powdered activated carbon from micro-polluted water in the presence of dissolved humic acid.

    PubMed

    Gong, Xujin; Li, Weiguang; Wang, Ke; Hu, Jinhua

    2013-08-01

    The adsorption of Cr(VI) (0.500 mg/L) onto food-grade tannic-acid immobilised powdered activated carbon (TA-PAC) in the presence of dissolved humic acid (DHA) was investigated at 280 K as a function of pH, along with the adsorption capacities and the adsorption isotherms for chromium ions. The results showed that the presence of DHA improved the adsorption capacities of Cr(VI) and its reduction product (Cr(III)) over a wide pH range (4.0-8.0). The main mechanism for metal-DHA complexation in the Cr(VI) system was the reduction of Cr(VI) followed by complexation between Cr(III) and DHA. The Freundlich isotherms yielded the best fits to all data (R(2)=0.9951, qm=5.639 mg/g) in the presence of DHA. The adsorption mechanisms of Cr(VI) onto TA-PAC in the presence of DHA were summarized into three categories: (i) binding by anion adsorption, (ii) Cr(VI) reduction followed by Cr(III) adsorption, and (iii) adsorption of Cr(III)-DHA complexes. PMID:23453800

  10. Effects of sludge retention times on reactivity of effluent dissolved organic matter for trihalomethane formation in hybrid powdered activated carbon membrane bioreactors.

    PubMed

    Ma, Defang; Gao, Baoyu; Xia, Chufan; Wang, Yan; Yue, Qinyan; Li, Qian

    2014-08-01

    In this study, real municipal wastewater intended for reuse was treated by two identical hybrid PAC/MBRs (membrane bioreactors with powdered activated carbon addition), which were operated at sludge retention times (SRTs) of 30 and 180 days, respectively. In order to investigate the effects of SRT on trihalomethane (THM) formation in chlorinated PAC/MBR effluents, characteristics and THM formation reactivity of effluent dissolved organic matter (EfOM) at different SRTs were examined. PAC/MBR-180 had higher level of EfOM, which contained less simple aromatic proteins and exhibited lower specific UV absorbance. EfOM with molecular weight <5 kDa from PAC/MBR-30 (23%) was lower than PAC/MBR-180 (26%). About 50% of EfOM from PAC/MBR-30 was hydrophobic acids, which was higher than that from PAC/MBR-180 (about 36%). EfOM at SRT 180 days exhibited higher hydrophilicity. Prolonging SRT greatly reduced THM formation reactivity of EfOM, but increased the formation of bromine-containing species during chlorination of PAC/MBR effluents. PMID:24929809

  11. Enhanced coagulation with powdered activated carbon or MIEX secondary treatment: a comparison of disinfection by-product formation and precursor removal.

    PubMed

    Watson, Kalinda; Farré, Maria José; Knight, Nicole

    2015-01-01

    The removal of both organic and inorganic disinfection by-product (DBP) precursors prior to disinfection is important in mitigating DBP formation, with halide removal being particularly important in salinity-impacted water sources. A matrix of waters of variable alkalinity, halide concentration and dissolved organic carbon (DOC) concentration were treated with enhanced coagulation (EC) followed by anion exchange (MIEX resin) or powdered activated carbon (PAC) and the subsequent disinfection by-product formation potentials (DBP-FPs) assessed and compared to DBP-FPs for untreated samples. Halide and DOC removal were also monitored for both treatment processes. Bromide and iodide adsorption by MIEX treatment ranged from 0 to 53% and 4-78%, respectively. As expected, EC and PAC treatments did not remove halides. DOC removal by EC/PAC was 70 ± 10%, while EC/MIEX enabled a DOC removal of 66 ± 12%. Despite the halide removals achieved by MIEX, increases in brominated disinfection by-product (Br-DBP) formation were observed relative to untreated samples, when favourable Br:DOC ratios were created by the treatment. However, the increases in formation were less than what was observed for the EC/PAC treated waters, which caused large increases in Br-DBP formation when high Br-DBP-forming water quality conditions occurred. The formation potential of fully chlorinated DBPs decreased after treatment in all cases. PMID:25462752

  12. The enhanced removal of carbonaceous and nitrogenous disinfection by-product precursors using integrated permanganate oxidation and powdered activated carbon adsorption pretreatment.

    PubMed

    Chu, Wenhai; Yao, Dechang; Gao, Naiyun; Bond, Tom; Templeton, Michael R

    2015-12-01

    Pilot-scale tests were performed to reduce the formation of a range of carbonaceous and nitrogenous disinfection by-products (C-, N-DBPs), by removing or transforming their precursors, with an integrated permanganate oxidation and powdered activated carbon adsorption (PM-PAC) treatment process before conventional water treatment processes (coagulation-sedimentation-filtration, abbreviated as CPs). Compared with the CPs, PM-PAC significantly enhanced the removal of DOC, DON, NH3(+)-N, and algae from 52.9%, 31.6%, 71.3%, and 83.6% to 69.5%, 61.3%, 92.5%, and 97.5%, respectively. PM pre-oxidation alone and PAC pre-adsorption alone did not substantially reduce the formation of dichloroacetonitrile, trichloroacetonitrile, N-nitrosodimethylamine and dichloroacetamide. However, the PM-PAC integrated process significantly reduced the formation of both C-DBPs and N-DBPs by 60-90% for six C-DBPs and 64-93% for six N-DBPs, because PM oxidation chemically altered the molecular structures of nitrogenous organic compounds and increased the adsorption capacity of the DBP precursors, thus highlighting a synergistic effect of PM and PAC. PM-PAC integrated process is a promising drinking water technology for the reduction of a broad spectrum of C-DBPs and N-DBPs. PMID:26065622

  13. Powdered activated carbon adsorption of two fishy odorants in water: Trans,trans-2,4-heptadienal and trans,trans-2,4-decadienal.

    PubMed

    Li, Xin; Wang, Jun; Zhang, Xiaojian; Chen, Chao

    2015-06-01

    Powdered activated carbon (PAC) adsorption of two fishy odorants, trans,trans-2,4-heptadienal (HDE) and trans,trans-2,4-decadienal (DDE), was investigated. Both the pseudo first-order and the pseudo second-order kinetic models well described the kinetics curves, and DDE was more readily removed by PAC. In isotherm tests, both Freundlich and Modified Freundlich isotherms fitted the experimental data well. PAC exhibited a higher adsorption capacity for DDE than for HDE, which could be ascribed to the difference in their hydrophobicity. The calculated thermodynamic parameters (ΔG0, ΔH0, and ΔS0) indicated an exothermic and spontaneous adsorption process. PAC dosage, pH, and natural organic matter (NOM) presence were found to influence the adsorption process. With increasing PAC dosage, the pseudo first-order and pseudo second-order rate constants both increased. The value of pH had little influence on HDE or DDE molecules but altered the surface charge of PAC, and the maximum adsorption capacity occurred at pH9. The presence of NOM, especially the fraction with molecular weight less than 1k Dalton, hindered the adsorption. The study showed that preloaded NOM impaired the adsorption capacity of HDE or DDE more severely than simultaneously fed NOM did. PMID:26040727

  14. Promoting the bio-cathode formation of a constructed wetland-microbial fuel cell by using powder activated carbon modified alum sludge in anode chamber

    PubMed Central

    Xu, Lei; Zhao, Yaqian; Doherty, Liam; Hu, Yuansheng; Hao, Xiaodi

    2016-01-01

    MFC centered hybrid technologies have attracted attention during the last few years due to their compatibility and dual advantages of energy recovery and wastewater treatment. In this study, a MFC was integrated into a dewatered alum sludge (DAS)- based vertical upflow constructed wetland (CW). Powder activate carbon (PAC) was used in the anode area in varied percentage with DAS to explore its influences on the performance of the CW-MFC system. The trial has demonstrated that the inclusion of PAC improved the removal efficiencies of COD, TN and RP. More significantly, increasing the proportion of PAC from 2% to 10% can significantly enhance the maximum power densities from 36.58 mW/m2 to 87.79 mW/m2. The induced favorable environment for bio-cathode formation might be the main reason for this improvement since the content of total extracellular polymeric substances (TEPS) of the substrate in the cathode area almost doubled (from 44.59 μg/g wet sludge to 87.70 μg/g wet sludge) as the percentage of PAC increased to 10%. This work provides another potential usage of PAC in CW-MFCs with a higher wastewater treatment efficiency and energy recovery. PMID:27197845

  15. The Friction Evolution of Siliceous Rocks during High-Velocity Slip By Thermal Activated Transition from Powder Lubrication and Rolling to Gouge Melting

    NASA Astrophysics Data System (ADS)

    Chen, X.; Madden, A. S.; Reches, Z.

    2014-12-01

    Experimental analyses of the frictional strength of siliceous rocks (granite, tonalite, and diorite) sheared in a rotary apparatus in the velocity range of 0.002-1 m/s (0.3-7.1 MPa, 0.002 - 1 m/s, total slip up to 60 m) revealed that: (1) During long slip-distances (tens of m) at low to moderate velocity (< 5 cm/s) the friction coefficient evolves with a weakening-strengthening-weakening path (Fig. 1a); and (2) The dependence of the friction coefficient on the slip-velocity is non-monotonous with weakening-strengthening-weakening sections (Fig. 1b) (Reches & Lockner, 2010). In a typical run with granite (Fig. 1a), the friction coefficient dropped from a static value of 0.86 to a steady value of 0.35 after 2.5 m of slip, followed by a sharp increase to 0.5±0.1 after ~7 m that was maintained for the next 10 m. Then, the friction started to increase again at 17 m to 0.78 at ~20 m, and finally dropped rapidly to 0.4. The first weakening stage (< 2.5m) is associated with formation of cohesive gouge flakes made of mixture of partially hydrated and recrystallized fine-grained gouge (20-50 nm). The top of these flakes displayed cylindrical rolls, 1 micron in diameter, oriented normal to slip, and the macroscopic weakening correlates with the presence of abundant rolls. SEM analysis of fault surfaces at the second weakening stage (> 17m) revealed abundant melt features such as stretched melt drops, melt coating of solid grains and abundant voids in the melt matrix, contrasting with the total melt in high velocity experiments. These friction-distance curves in our granite experiments (e.g., Fig. 1a) bears a similar path of gabbro friction curve at high velocity (Hirose and Shimamoto 2005). We propose that this non-monotonous friction evolution can be explained as a phase transition from initial pulverization of the brittle stage (low velocity, low normal stress, small slip distance), that leads to powder lubrication by powder rolling, to partial-to-full melting of the

  16. Inactivated E. coli transformed with plasmids that produce dsRNA against infectious salmon anemia virus hemagglutinin show antiviral activity when added to infected ASK cells

    PubMed Central

    García, Katherine; Ramírez-Araya, Sebastián; Díaz, Álvaro; Reyes-Cerpa, Sebastián; Espejo, Romilio T.; Higuera, Gastón; Romero, Jaime

    2015-01-01

    Infectious salmon anemia virus (ISAV) has caused great losses to the Chilean salmon industry, and the success of prevention and treatment strategies is uncertain. The use of RNA interference (RNAi) is a promising approach because during the replication cycle, the ISAV genome must be transcribed to mRNA in the cytoplasm. We explored the capacity of E. coli transformed with plasmids that produce double-stranded RNA (dsRNA) to induce antiviral activity when added to infected ASK cells. We transformed the non-pathogenic Escherichia coli HT115 (DE3) with plasmids that expressed highly conserved regions of the ISAV genes encoding the nucleoprotein (NP), fusion (F), hemagglutinin (HE), and matrix (M) proteins as dsRNA, which is the precursor of the RNAi mechanism. The inactivated transformed bacteria carrying dsRNA were tested for their capacity to silence the target ISAV genes, and the dsRNA that were able to inhibit gene expression were subsequently tested for their ability to attenuate the cytopathic effect (CPE) and reduce the viral load. Of the four target genes tested, inactivated E. coli transformed with plasmids producing dsRNA targeting HE showed antiviral activity when added to infected ASK cells. PMID:25932022

  17. EGFR Activation Leads to Cell Death Independent of PI3K/AKT/mTOR in an AD293 Cell Line

    PubMed Central

    Popeda, Marta; Ksiazkiewicz, Magdalena; Grzela, Dawid P.; Walczak, Maciej P.; Banaszczyk, Mateusz; Peciak, Joanna; Stoczynska-Fidelus, Ewelina; Rieske, Piotr

    2016-01-01

    The Epidermal Growth Factor Receptor (EGFR) and its mutations contribute in various ways to tumorigenesis and biology of human cancers. They are associated with tumor proliferation, progression, drug resistance and the process of apoptosis. There are also reports that overexpression and activation of wild-type EGFR may lead to cell apoptosis. To study this phenomenon, we overexpressed in an AD293 cell line two most frequently observed forms of the EGFR receptor: wild-type and the constitutively active mutant–EGFR variant III (EGFRvIII). Then, we compared the effect of EGF stimulation on cell viability and downstream EGFR signaling. AD293 cells overexpressing wild-type EGFR, despite a significant proliferation increase in serum supplemented medium, underwent apoptosis after EGF stimulation in serum free conditions. EGFRvIII expressing cells, however, were unaffected by either serum starvation or EGF treatment. The effect of EGF was completely neutralized by tyrosine kinase inhibitors (TKIs), indicating the specificity of this observation. Moreover, apoptosis was not prevented by inhibiting EGFR downstream proteins (PI3K, AKT and mTOR). Here we showed another EGFR function, dependent on environmental factors, which could be employed in therapy and drug design. We also proposed a new tool for EGFR inhibitor analysis. PMID:27153109

  18. Inactivated E. coli transformed with plasmids that produce dsRNA against infectious salmon anemia virus hemagglutinin show antiviral activity when added to infected ASK cells.

    PubMed

    García, Katherine; Ramírez-Araya, Sebastián; Díaz, Álvaro; Reyes-Cerpa, Sebastián; Espejo, Romilio T; Higuera, Gastón; Romero, Jaime

    2015-01-01

    Infectious salmon anemia virus (ISAV) has caused great losses to the Chilean salmon industry, and the success of prevention and treatment strategies is uncertain. The use of RNA interference (RNAi) is a promising approach because during the replication cycle, the ISAV genome must be transcribed to mRNA in the cytoplasm. We explored the capacity of E. coli transformed with plasmids that produce double-stranded RNA (dsRNA) to induce antiviral activity when added to infected ASK cells. We transformed the non-pathogenic Escherichia coli HT115 (DE3) with plasmids that expressed highly conserved regions of the ISAV genes encoding the nucleoprotein (NP), fusion (F), hemagglutinin (HE), and matrix (M) proteins as dsRNA, which is the precursor of the RNAi mechanism. The inactivated transformed bacteria carrying dsRNA were tested for their capacity to silence the target ISAV genes, and the dsRNA that were able to inhibit gene expression were subsequently tested for their ability to attenuate the cytopathic effect (CPE) and reduce the viral load. Of the four target genes tested, inactivated E. coli transformed with plasmids producing dsRNA targeting HE showed antiviral activity when added to infected ASK cells.

  19. Interference of iron as a coagulant on MIB removal by powdered activated carbon adsorption for low turbidity waters.

    PubMed

    Seckler, Ferreira Filho Sidney; Margarida, Marchetto; Rosemeire, Alves Laganaro

    2013-08-01

    Powered activated carbon (PAC) is widely used in water treatment plants to minimize odors in drinking water. This study investigated the removal of 2-methylisoborneol (MIB) by PAC adsorption, combined with coagulation using iron as a coagulant. The adsorption and coagulation process were studied through different case scenarios of jar tests. The analysis evaluated the effect of PAC dosing in the liquid phase immediately before or after the coagulant addition. Ferric sulphate was used as the coagulant with dosages from 10 to 30 mg/L, and PAC dosages varied from 10 to 40 mg/L. The highest MIB removal efficiency (about 70%) was achieved without the coagulant addition and with the highest PAC dosage (40 mg/L). Lower MIB removal efficiencies were observed in the presence of coagulant, showing a clear interference of the iron precipitate or coagulant in the adsorption process. The degree of interference of the coagulation process in the MIB removal was proportional to the ratio of ferric hydroxide mass to the PAC mass. For both cases of PAC dosing, upstream and downstream of the coagulant injection point, the MIB removal efficiency was similar. However, MIB removal efficiency was 15% lower when compared with experiments without the coagulant application. This interference in the MIB adsorption occurs potentially because the coagulant coats the surface of the carbon and interferes with the MIB coming in contact with the carbon's surface and pores. This constraint requires an increase of the PAC dosage to provide the same efficiency observed without coagulation. PMID:24520695

  20. Evaluation of the use of powdered activated carbon in membrane bioreactor for the treatment of bleach pulp mill effluent.

    PubMed

    Amaral, Míriam C S; Lange, Liséte C; Borges, Cristiano P

    2014-09-01

    In this paper, the use of powered activated carbon (PAC) in membrane bioreactor (MBR) employed in the treatment of bleach pulp mill effluents was evaluated. The MBR was operated with hydraulic residence time of 9.5 h and PAC concentration of 10 g/L. The addition of PAC to the MBR reduced the average concentration of chemical oxygen demand (COD) in the permeate from 215 mg/L (82% removal efficiency) to 135 mg/L (88% removal efficiency), producing an effluent that can be reused on bleaching stage. Moreover, the addition of PAC to the MBR resulted in the reduction in applied pressure and provided a more stable operation during the monitoring period. This occurrence was probably due to the increase of critical flux after the addition of PAC. The fouling mechanism was investigated and the results showed that controlling the concentration of soluble microbial products (SMP) and extracellular polymeric substance (EPS) by using PAC and keeping the operational flux below critical flux is of major importance for MBR operational sustainability. PMID:25327019

  1. Photocatalysis of phenol and salicyclic acid by nanostructured titania powders

    SciTech Connect

    Fotou, G.P.; Pratsinis, S.E.

    1995-12-31

    The photocatalytic destruction of phenol and salicylic acid was studied in aqueous suspensions of titania powders made in flame reactors. These powders were made in six hydrocarbon diffusion flames by hydrolysis and oxidation of TiCl{sub 4} that resulted in powders of high specific surface area and high anatase content. The photoactivity of the flame-made titania powders was compared with that of commercially available powders. Doping the titania with SiO{sub 2} was detrimental to the photoactivity of the powders in aerated solutions in contrast to non-aerated solutions. Titania powders in the range of 20-40 nm containing small amounts of rutile were more active than pure anatase powders. The phenol degradation reaction followed a first-order law while the Langmuir-Hinshelwood model was found to most accurately represent the photodegradation of salicylic acid.

  2. Microencapsulated jabuticaba (Myrciaria cauliflora) extract added to fresh sausage as natural dye with antioxidant and antimicrobial activity.

    PubMed

    Baldin, Juliana Cristina; Michelin, Euder Cesar; Polizer, Yana Jorge; Rodrigues, Isabela; de Godoy, Silvia Helena Seraphin; Fregonesi, Raul Pereira; Pires, Manoela Alves; Carvalho, Larissa Tátero; Fávaro-Trindade, Carmen Silvia; de Lima, César Gonçalves; Fernandes, Andrezza Maria; Trindade, Marco Antonio

    2016-08-01

    The aim was to evaluate the addition of microencapsulated jabuticaba extract (MJE) to fresh sausage as natural dye with antioxidant and antimicrobial activity. Fresh sausages without dye, with cochineal carmine and with addition of 2% and 4% MJE were evaluated for chemical, microbiological and sensory properties during 15days of refrigerated storage. TBARS values were lower (P<0.05) throughout the storage period in sausages with 2% and 4% MJE (below 0.1mg of malondialdehyde/kg sample) than in control and carmine treatments (from 0.3 to 0.6mg of malondialdehyde/kg sample). T2% and T4% also showed lower microbial counts on storage days 4 and 15 for APCs. The addition of 4% MJE negatively influenced (P<0.05) sensory color, texture and overall acceptance attributes. On the other hand, T2% presented similar (P>0.05) sensory acceptance to control and carmine treatments in most of the attributes evaluated except for a decrease in color. Thus, addition of 2% MJE to fresh sausage can be considered as a natural pigment ingredient.

  3. Microencapsulated jabuticaba (Myrciaria cauliflora) extract added to fresh sausage as natural dye with antioxidant and antimicrobial activity.

    PubMed

    Baldin, Juliana Cristina; Michelin, Euder Cesar; Polizer, Yana Jorge; Rodrigues, Isabela; de Godoy, Silvia Helena Seraphin; Fregonesi, Raul Pereira; Pires, Manoela Alves; Carvalho, Larissa Tátero; Fávaro-Trindade, Carmen Silvia; de Lima, César Gonçalves; Fernandes, Andrezza Maria; Trindade, Marco Antonio

    2016-08-01

    The aim was to evaluate the addition of microencapsulated jabuticaba extract (MJE) to fresh sausage as natural dye with antioxidant and antimicrobial activity. Fresh sausages without dye, with cochineal carmine and with addition of 2% and 4% MJE were evaluated for chemical, microbiological and sensory properties during 15days of refrigerated storage. TBARS values were lower (P<0.05) throughout the storage period in sausages with 2% and 4% MJE (below 0.1mg of malondialdehyde/kg sample) than in control and carmine treatments (from 0.3 to 0.6mg of malondialdehyde/kg sample). T2% and T4% also showed lower microbial counts on storage days 4 and 15 for APCs. The addition of 4% MJE negatively influenced (P<0.05) sensory color, texture and overall acceptance attributes. On the other hand, T2% presented similar (P>0.05) sensory acceptance to control and carmine treatments in most of the attributes evaluated except for a decrease in color. Thus, addition of 2% MJE to fresh sausage can be considered as a natural pigment ingredient. PMID:27016672

  4. Antioxidant activity of phenolic compounds added to a functional emulsion containing omega-3 fatty acids and plant sterol esters.

    PubMed

    Espinosa, Raquel Rainho; Inchingolo, Raffaella; Alencar, Severino Matias; Rodriguez-Estrada, Maria Teresa; Castro, Inar Alves

    2015-09-01

    The effect of eleven compounds extracted from red propolis on the oxidative stability of a functional emulsion was evaluated. Emulsions prepared with Echium oil as omega 3 (ω-3 FA) source, containing 1.63 g/100mL of α-linolenic acid (ALA), 0.73 g/100 mL of stearidonic acid (SDA) and 0.65 g/100mL of plant sterol esters (PSE) were prepared without or with phenolic compounds (vanillic acid, caffeic acid, trans-cinnamic acid, 2,4-dihydroxycinnamic acid, p-coumaric acid, quercetin, trans-ferulic acid, trans,trans-farnesol, rutin, gallic acid or sinapic acid). tert-Butylhydroquinone and a mixture containing ascorbic acid and FeSO4 were applied as negative and positive controls of the oxidation. Hydroperoxide, thiobarbituric acid reactive substances (TBARS), malondialdehyde and phytosterol oxidation products (POPs) were evaluated as oxidative markers. Based on hydroperoxide and TBARS analysis, sinapic acid and rutin (200 ppm) showed the same antioxidant activity than TBHQ, representing a potential alternative as natural antioxidant to be applied in a functional emulsion containing ω-3 FA and PSE.

  5. Nonaqueous solution synthesis process for preparing oxide powders of lead zirconate titanate and related materials

    DOEpatents

    Voigt, J.A.; Sipola, D.L.; Tuttle, B.A.; Anderson, M.T.

    1999-06-01

    A process is disclosed for producing powders of perovskite-type compounds which comprises mixing a metal alkoxide solution with a lead acetate solution to form a homogeneous, clear metal solution, adding an oxalic acid/n-propanol solution to this metal solution to form an easily filterable, free-flowing precursor powder and then calcining this powder. This process provides fine perovskite-phase powders with ferroelectric properties which are particularly useful in a variety of electronic applications. 4 figs.

  6. Nonaqueous solution synthesis process for preparing oxide powders of lead zirconate titanate and related materials

    DOEpatents

    Voigt, James A.; Sipola, Diana L.; Tuttle, Bruce A.; Anderson, Mark T.

    1999-01-01

    A process for producing powders of perovskite-type compounds which comprises mixing a metal alkoxide solution with a lead acetate solution to form a homogeneous, clear metal solution, adding an oxalic acid/n-propanol solution to this metal solution to form an easily filterable, free-flowing precursor powder and then calcining this powder. This process provides fine perovskite-phase powders with ferroelectric properties which are particularly useful in a variety of electronic applications.

  7. Enhanced Recyclable Magnetized Palm Shell Waste-Based Powdered Activated Carbon for the Removal of Ibuprofen: Insights for Kinetics and Mechanisms

    PubMed Central

    Wong, Kien Tiek; Yoon, Yeomin; Jang, Min

    2015-01-01

    A novel preparation method of magnetized palm shell waste-based powdered activated carbon (MPPAC, avg. size 112 μm) was developed. The prepared MPPAC was assessed by several physicochemical analyses, and batch tests were performed for ibuprofen (IBP) removal. Field emission scanning electron microscopy (FESEM) and N2 gas isotherms revealed that magnetite and maghemite were homogeneous and deposited mostly on the surface of PPAC without a significant clogging effect on the micropores. Isotherm results showed that 3.8% Fe (w/w) impregnated PPAC [MPPAC-Fe(3.8%)] had about 2.2-fold higher maximum sorption capacity (157.3 mg g-1) and a 2.5-fold higher sorption density (0.23 mg m-2) than pristine PPAC. Both Fourier-transform infrared spectroscopy (FTIR) and isotherm data indicated that the high sorption capacity and density of IBP by MPPAC was primarily attributable to donor-acceptor complexes with the C = O group and dispersive π-π interactions with the carbon surface. Based on kinetic and repeated adsorption tests, pore diffusion was the rate-limiting step, and MPPAC-Fe(3.8%) had about 1.9~2.8- and 9.1~15.8-fold higher rate constants than MPPAC-Fe(8.6%) and palm shell-waste granular activated carbon (PGAC, avg. size 621 μm), respectively. MPPAC showed almost eight fold greater re-adsorption capacity than PPAC due to a thermal catalytic effect of magnetite/maghemite. PMID:26496196

  8. Enhanced Recyclable Magnetized Palm Shell Waste-Based Powdered Activated Carbon for the Removal of Ibuprofen: Insights for Kinetics and Mechanisms.

    PubMed

    Wong, Kien Tiek; Yoon, Yeomin; Jang, Min

    2015-01-01

    A novel preparation method of magnetized palm shell waste-based powdered activated carbon (MPPAC, avg. size 112 μm) was developed. The prepared MPPAC was assessed by several physicochemical analyses, and batch tests were performed for ibuprofen (IBP) removal. Field emission scanning electron microscopy (FESEM) and N2 gas isotherms revealed that magnetite and maghemite were homogeneous and deposited mostly on the surface of PPAC without a significant clogging effect on the micropores. Isotherm results showed that 3.8% Fe (w/w) impregnated PPAC [MPPAC-Fe(3.8%)] had about 2.2-fold higher maximum sorption capacity (157.3 mg g-1) and a 2.5-fold higher sorption density (0.23 mg m-2) than pristine PPAC. Both Fourier-transform infrared spectroscopy (FTIR) and isotherm data indicated that the high sorption capacity and density of IBP by MPPAC was primarily attributable to donor-acceptor complexes with the C = O group and dispersive π-π interactions with the carbon surface. Based on kinetic and repeated adsorption tests, pore diffusion was the rate-limiting step, and MPPAC-Fe(3.8%) had about 1.9~2.8- and 9.1~15.8-fold higher rate constants than MPPAC-Fe(8.6%) and palm shell-waste granular activated carbon (PGAC, avg. size 621 μm), respectively. MPPAC showed almost eight fold greater re-adsorption capacity than PPAC due to a thermal catalytic effect of magnetite/maghemite. PMID:26496196

  9. Enhanced Recyclable Magnetized Palm Shell Waste-Based Powdered Activated Carbon for the Removal of Ibuprofen: Insights for Kinetics and Mechanisms.

    PubMed

    Wong, Kien Tiek; Yoon, Yeomin; Jang, Min

    2015-01-01

    A novel preparation method of magnetized palm shell waste-based powdered activated carbon (MPPAC, avg. size 112 μm) was developed. The prepared MPPAC was assessed by several physicochemical analyses, and batch tests were performed for ibuprofen (IBP) removal. Field emission scanning electron microscopy (FESEM) and N2 gas isotherms revealed that magnetite and maghemite were homogeneous and deposited mostly on the surface of PPAC without a significant clogging effect on the micropores. Isotherm results showed that 3.8% Fe (w/w) impregnated PPAC [MPPAC-Fe(3.8%)] had about 2.2-fold higher maximum sorption capacity (157.3 mg g-1) and a 2.5-fold higher sorption density (0.23 mg m-2) than pristine PPAC. Both Fourier-transform infrared spectroscopy (FTIR) and isotherm data indicated that the high sorption capacity and density of IBP by MPPAC was primarily attributable to donor-acceptor complexes with the C = O group and dispersive π-π interactions with the carbon surface. Based on kinetic and repeated adsorption tests, pore diffusion was the rate-limiting step, and MPPAC-Fe(3.8%) had about 1.9~2.8- and 9.1~15.8-fold higher rate constants than MPPAC-Fe(8.6%) and palm shell-waste granular activated carbon (PGAC, avg. size 621 μm), respectively. MPPAC showed almost eight fold greater re-adsorption capacity than PPAC due to a thermal catalytic effect of magnetite/maghemite.

  10. Improvement of the thermostability and activity of halohydrin dehalogenase from Agrobacterium radiobacter AD1 by engineering C-terminal amino acids.

    PubMed

    Wang, Xiong; Han, Shaoqiang; Yang, Zujun; Tang, Lixia

    2015-10-20

    In the current study, a three-tiered mutagenesis strategy was employed to simultaneously improve the thermostability and activity of halohydrin dehalogenase from Agrobacterium radiobacter AD1 (HheC) by engineering the last ten amino acids (Met245∼Glu254) of its C-terminal region. Initially, truncated mutagenesis results displayed that C-terminal deletions decreased the thermostability and/or activity of HheC. Then ten residues were subjected to single-site saturation mutagenesis, resulting in 20 beneficial single-point variants related to the thermostability or activity of HheC. The results clearly indicated that residues Met252∼Glu254 and Trp249 are crucial for regulating enzyme thermostability and activity, respectively. Finally, the beneficial substitutions were combined using efficient multi-site combinatorial mutagenesis approaches, leading to an outstanding variant PX14 (Trp249Pro/Met252Leu/Pro253Asp), which had a 17.8-fold higher half-life and a 4.0-fold higher kcat value than that of wild-type HheC. These results indicated that the C-terminal residues play an important role in modulating both the thermostability and activity of HheC.

  11. Sintering titanium powders

    SciTech Connect

    Gerdemann, Stephen J.; Alman, David E.

    2005-09-01

    Recently, there has been renewed interest in low-cost titanium. Near-net-shape powder metallurgy offers the potential of manufacturing titanium articles without costly and difficult forming and machining operations; hence, processing methods such as conventional press-and-sinter, powder forging and powder injection molding are of interest. The sintering behavior of a variety of commercial and experimental titanium powders was studied. Commercial powders were acquired that were produced different routes: (i) sponge fines from the primary titanium processing; (ii) via the hydride-dehydride process; and (iii) gas atomization. The influence of vacuum sintering time (0.5 to 32 hrs) and temperature (1200, 1275 or 1350°C) on the microstructure (porosity present) of cold pressed powders was studied. The results are discussed in terms of the difference in powder characteristics, with the aim of identify the characteristics required for full density via press-and-sinter processing. Near-net-shape tensile bars were consolidated via cold pressed and sintered. After sintering, a sub-set of the tensile bars was hot-isostatic pressed (HIPed). The microstructure and properties of the bars were compared in the sintered and HIPed conditions.

  12. Ceramic powder compaction

    SciTech Connect

    Glass, S.J.; Ewsuk, K.G.; Mahoney, F.M.

    1995-12-31

    With the objective of developing a predictive model for ceramic powder compaction we have investigated methods for characterizing density gradients in ceramic powder compacts, reviewed and compared existing compaction models, conducted compaction experiments on a spray dried alumina powder, and conducted mechanical tests and compaction experiments on model granular materials. Die filling and particle packing, and the behavior of individual granules play an important role in determining compaction behavior and should be incorporated into realistic compaction models. These results support the use of discrete element modeling techniques and statistical mechanics principals to develop a comprehensive model for compaction, something that should be achievable with computers with parallel processing capabilities.

  13. Excitation function for deuteron induced nuclear reactions on natural ytterbium for production of high specific activity 177g Lu in no-carrier-added form for metabolic radiotherapy.

    PubMed

    Manenti, Simone; Groppi, Flavia; Gandini, Andrea; Gini, Luigi; Abbas, Kamel; Holzwarth, Uwe; Simonelli, Federica; Bonardi, Mauro

    2011-01-01

    Deuteron-induced nuclear reactions for generation of no-carrier-added Lu radionuclides were investigated using the stacked-foil activation technique on natural Yb targets at energies up to E(d)=18.18 MeV. Excitation functions of the reactions (nat)Yb(d,xn)(169,170,171,172,173,174g,174m,176m,177g)Lu and (nat)Yb(d,pxn)(169,175,177)Yb have been measured, among them three ((169)Lu, (174m)Lu and (176m)Lu) are reported for the first time. The upper limit of the contamination from the long-lived metastable level (177m)Lu was evaluated too. Thick-target yields for all investigated radionuclides are calculated.

  14. Powdered activated carbons as effective phases for bar adsorptive micro-extraction (BAμE) to monitor levels of triazinic herbicides in environmental water matrices.

    PubMed

    Neng, N R; Mestre, A S; Carvalho, A P; Nogueira, J M F

    2011-02-15

    Bar adsorptive micro-extraction using three powdered activated carbons (ACs) as adsorbent phases followed by liquid desorption and high performance liquid chromatography with diode array detection (BAμE(ACs)-LD/HPLC-DAD), was developed to monitor triazinic herbicides (atrazine, simazine and terbutylazine) in environmental water matrices. ACs used present apparent surface areas around 1000 m(2) g(-1) with an important mesoporous volume and distinct surface chemistry characteristics (pH(PZC) ranging from 6.5 to 10.4). The textural and surface chemistry properties of the ACs adsorbent phases were correlated with the analytical data for a better understanding of the overall enrichment process. Assays performed on 10 mL water samples spiked at the 10.0 μg L(-1) levels under optimized experimental conditions yielded recoveries around 100% for the three herbicides under study. The analytical performance showed good precision (RSD<15.0%), convenient detection limits (≈0.1 μg L(-1)) and suitable linearity (1.0-12.0 μg L(-1)) with good correlation coefficients (r(2)>0.9914). By using the standard addition method, the application of the present method on real water matrices, such as surface water and wastewater, allowed very good performances at the trace level. The proposed methodology proved to be a suitable sorptive extraction alternative for the analysis of priority pollutants with polar characteristics, showing to be easy to implement, reliable, sensitive and requiring a low sample volume to monitor triazinic compounds in water matrices. PMID:21238763

  15. Adsorption of geosmin and 2-methylisoborneol onto powdered activated carbon at non-equilibrium conditions: influence of NOM and process modelling.

    PubMed

    Zoschke, Kristin; Engel, Christina; Börnick, Hilmar; Worch, Eckhard

    2011-10-01

    The adsorption of the taste and odour (T&O) compounds geosmin and 2-methylisoborneol (2-MIB) onto powdered activated carbon (PAC) has been studied under conditions which are typical for a drinking water treatment plant that uses reservoir water for drinking water production. The reservoir water as well as the pre-treated water (after flocculation) contains NOM that competes with the trace compounds for the adsorption sites on the carbon surface. Although the DOC concentrations in the reservoir water and in the pre-treated water were different, no differences in the competitive adsorption could be seen. By using two special characterisation methods for NOM (adsorption analysis, LC/OCD) it could be proved that flocculation removes only NOM fractions which are irrelevant for competitive adsorption. Different model approaches were applied to describe the competitive adsorption of the T&O compounds and NOM, the tracer model, the equivalent background compound model, and the simplified equivalent background compound model. All these models are equilibrium models but in practice the contact time in flow-through reactors is typically shorter than the time needed to establish the adsorption equilibrium. In this paper it is demonstrated that the established model approaches can be used to describe competitive adsorption of T&O compounds and NOM also under non-equilibrium conditions. The results of the model applications showed that in particular the simplified equivalent background compound model is a useful tool to determine the PAC dosage required to reduce the T&O compounds below the threshold concentration. PMID:21752419

  16. Evaluation of pristine and Eu ₂O₃-added MgB ₂ ceramics for medical applications: hardness, corrosion resistance, cytotoxicity and antibacterial activity.

    PubMed

    Batalu, Dan; Stanciuc, Ana Maria; Moldovan, Lucia; Aldica, Gheorghe; Badica, Petre

    2014-09-01

    Nano- or micropowders of Eu2O3 were added to MgB2, resulting in a composition of (MgB2)0.975(EuO1.5)0.025. Pristine and doped samples were prepared using spark plasma sintering and tested for (i) Vickers hardness, (ii) pH evolution in phosphate-buffered saline solution, (iii) corrosion resistance (Tafel polarization curves), (iv) cytotoxicity (in vitro tests), and (v) antibacterial activity. Eu2O3 addition influenced the investigated properties. Solutions of MgB2-based samples show a relatively high saturation pH of 8.5. This value is lower than that of solutions incubated with Mg or other Mg-based biodegradable alloys reported in the literature. MgB2-based samples have lower electro-corrosion rates than Mg. Their Vickers hardness is 6.8-10.2GPa, and these values are higher than those of biodegradable Mg-based alloys. MgB2 has low in vitro biocompatibility, good antibacterial activity against Escherichia coli, and mild activity against Staphylococcus aureus. Our results suggest that MgB2-based materials deserve attention in biomedical applications, such as implants or sterile medical instruments.

  17. AdS duals of matrix strings

    NASA Astrophysics Data System (ADS)

    Morales, Jose F.; Samtleben, Henning

    2003-06-01

    We review recent work on the holographic duals of type II and heterotic matrix string theories described by warped AdS3 supergravities. In particular, we compute the spectra of Kaluza-Klein primaries for type I, II supergravities on warped AdS3 × S7 and match them with the primary operators in the dual two-dimensional gauge theories. The presence of non-trivial warp factors and dilaton profiles requires a modification of the familiar dictionary between masses and 'scaling' dimensions of fields and operators. We present these modifications for the general case of domain wall/QFT correspondences between supergravities on warped AdSd+1 × Sq geometries and super Yang-Mills theories with 16 supercharges.

  18. Talcum powder poisoning

    MedlinePlus

    ... powder As a filler in street drugs, like heroin Other products may also contain talc. ... have developed serious lung damage and cancer. Injecting heroin that contains talc into a vein may lead ...

  19. Gelcasting superalloy powders

    SciTech Connect

    Janney, M.A.

    1995-12-31

    Gelcasting is a process for forming inorganic powders into complex shapes. It was originally developed for ceramic powders. A slurry of powder and a monomer solution is poured in to mold and polymerized in-situ to form gelled parts. Typically, only 2-4 wt % Polymer is used. The process has both aqueous and nonaqueous versions. Gelcasting is a generic process and has been used to produce ceramic parts from over a dozen different ceramic compositions ranging from alumina-based refractories to high-performance silicon nitride. Recently, gelcasting has been applied to forming superalloy powders into complex shapes. This application has posed several challenges not previously encountered in ceramics. In particular, problems were caused by the larger particle size and the higher density of the particles. Additional problems were encountered with binder removal. How these problems were overcome will be described.

  20. Pyrotechnic filled molding powder

    DOEpatents

    Hartzel, Lawrence W.; Kettling, George E.

    1978-01-01

    The disclosure relates to thermosetting molding compounds and more particularly to a pyrotechnic filled thermosetting compound comprising a blend of unfilled diallyl phthalate molding powder and a pyrotechnic mixture.

  1. POWDER COAT APPLICATIONS

    EPA Science Inventory

    The report discusses an investigation of critical factors that affect the use of powder coatings on the environment, cost, quality, and production. The investigation involved a small business representative working with the National Defense Center for Environmental Excellence (ND...

  2. The effectiveness of the oncolytic activity induced by Ad5/F35 adenoviral vector is dependent on the cumulative cellular conditions of survival and autophagy.

    PubMed

    Kim, So Y; Kang, Sujin; Song, Jae J; Kim, Joo-Hang

    2013-04-01

    To overcome the poor tumor transduction efficiency of adenovirus serotype 5 (Ad5) observed in several types of cancer, the fiber region of Ad5, apart from its tail, was replaced by adenovirus serotype 35 (Ad35). The chimeric Ad5/F35 adenoviral vector did not exhibit any significant enhancement of transduction efficiency. CD46, a receptor for Ad35, was expressed in relatively small amounts in most of the cancer cells examined. Therefore, we investigated the pivotal factor(s) that render cancer cells susceptible to transduction. We discovered that the tumor transduction efficiency of Ad5/F35 was enhanced in the presence of rapamycin, an autophagy inducer, in some cancer cells. Analysis of survival potential and cell proliferation rates revealed that Ad5/F35 exerted a more pronounced oncolytic effect in cancer cells with higher survival potential in the presence of rapamycin.

  3. Late Holocene (ca. AD 370-1210) ecosystem changes inferred from a stalagmite from northwestern Madagascar: the role of the ITCZ and human activity

    NASA Astrophysics Data System (ADS)

    Voarintsoa, N. R. G.; Railsback, L. B.; Brook, G. A.; Wang, L.; Liang, F.; Cheng, H.; Edwards, R. L.

    2015-12-01

    High-resolution stable isotope records combined with petrographic examination of stalagmite MA3 from Anjohibe Cave provide a better understanding of the climatically- and anthropogenically- induced ecosystem change in NW Madagascar between ca. AD 370 and 1210. The record suggests strong climatic control prior to ca. 700 and strong influence of human activities after ca. 920. Prior to 700, monsoonal rainfall and ecosystem change seem to respond to the change in the relative position of the ITCZ. This is inferred from the positive correlation between δ13C and δ18O and T anomalies in the Northern Hemisphere. A cooler NH pushed the ITCZ southward, thus favoring longer visits in northwestern Madagascar and strengthening the Malagasy monsoon. This offered favorable conditions to vegetation cover growth (the opposite was possible during warmer NH). The period between ca. 675 and 700 is the driest and might represent a period of abrupt change in vegetation cover as suggested by the stalagmite's petrography, smaller layer specific width, and greater values of both δ13C and δ18O. This drier period is followed by slight change in hydrology and a gradual recovery in vegetation in NW Madagascar, which lasted until ca. 920. This change is reflected in the decrease of stable isotope values and an increase in the layer specific width. Since ca. 920, the records suggest that the ecosystem change around the cave was controlled by something other than climate. The coincidence in time with human settlement and the gradual shift from lower to higher δ13C would suggest a strong involvement of human activities, particularly the practice of "tavy" or slash-and burn activities. This finding is important because Madagascar has experienced major ecological changes since the late Holocene, the cause of which has raised two hypotheses as to whether caused by severe climate change or by human activities. Deciphering the difference between human-induced and abrupt climatic changes has been

  4. High-performance Ni3Al synthesized from composite powders

    NASA Astrophysics Data System (ADS)

    Chiou, Wen-Chih; Hu, Chen-Ti

    1994-05-01

    Specimens of Ni3Al + B of high density (>99.3 Pct RD) and relatively large dimension have been synthesized from composite powders through processes of replacing plating and electroless Ni-B plating on Al powder, sintering, and thermal-mechanical treatment. The uniformly coated Ni layer over fine Al or Ni core particles constituting these coating/core composite powders has advantages such as better resistance to oxidation relative to pure Al powder, a greater green density as a compacted powder than prealloyed powder, the possibility of atomically added B to the material by careful choice of a suitable plating solution, and avoidance of the expensive powder metallurgy (PM) equipment such as a hot isostatic press (HIP), hot press (HP), etc. The final Ni3Al + B product is made from Ni-B-Al and Ni-B-Ni mixed composite powders by means of traditional PM processes such as compacting, sintering, rolling, and annealing, and therefore, the dimensions of the product are not constrained by the capacity of an HIP or HP. The properties of Ni3Al composite powder metallurgy (CPM) specimens tested at room temperature have been obtained, and comparison with previous reports is conducted. A tensile elongation of about 16 Pct at room temperature was attained.

  5. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2004-09-14

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  6. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2005-05-10

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  7. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-07-29

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  8. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-26

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  9. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2005-01-25

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  10. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goval, Amit; Williams, Robert K.; Kroeger, Donald M.

    2005-06-07

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  11. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-19

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  12. Biaxially textured articles formed by powder metallurgy

    DOEpatents

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2004-09-28

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100}<100> orientation texture; and further having a Curie temperature less than that of pure Ni.

  13. NiAl powder alloys: II. Compacting of NiAl powders produced by various methods

    NASA Astrophysics Data System (ADS)

    Skachkov, O. A.; Povarova, K. B.; Drozdov, A. A.; Morozov, A. E.

    2012-05-01

    The technological properties of granulated NiAl powders produced by gas spraying of melts and NiAl powders produced by calcium hydride reduction (CHR) of mixtures of nickel and aluminum oxides are compared. The possibilities of production of compact workpieces from these powders using hydrostatic pressing, hot pressing, hot isostatic pressing, and hot extrusion are estimated. To improve compressibility, preliminary milling and/or mechanical activation of the powders are proposed. The strength properties of NiAl rods with a diameter of 20 mm extruded from a temperature of 1100°C and made from the granulated powders are slightly higher than those made from the CHR powders. At temperatures higher than 800°C the properties becomes similar. Transition point t d.b from the ductile to brittle state of samples made from powders sprayed in nitrogen and argon is 100-150°C higher than those made from the CHR powders. The difference in the mechanical properties is caused by the structural and chemical microheterogeneity of granules (microingots), which is inherited in the rods after hot deformation and annealing at 1200-1400°C and is (0.67-0.88) T m NiAl ( T m is the melting point, K).

  14. Effects of potent antiretroviral therapy on the immune activation marker soluble CD27 in patients infected with HIV-1 subtypes A-D.

    PubMed

    Atlas, Ann; Thanh Ha, Tran Thi; Lindström, Anna; Nilsson, Anna; Alaeus, Annette; Chiodi, Francesca; De Milito, Angelo

    2004-03-01

    HIV-1 genetic subtypes might have a different impact on disease progression and response to antiretroviral therapy (ART). Few data are available on the immune activation profile in patients with different HIV-1 subtypes. We have tested by ELISA the plasma levels of an immune activation marker, soluble CD27 (sCD27), in a cohort of 64 patients infected with HIV-1 subtypes A-D, at baseline and after 1 year of virologically successful ART. Plasma sCD27 was significantly higher in the whole HIV-1-infected population as compared to healthy subjects [522 U/ml (188-1,307) vs. 285 U/ml (174-397), P < 0.001]. Among the four different HIV-1 subtypes, patients with subtype C virus had significantly higher plasma sCD27 [684 U/ml, (188-1228)] as compared to patients with subtype A [428 U/ml (247-1307), P < 0.05] and B [454 (211-925), P < 0.05]. After 1 year of ART, plasma sCD27 significantly decreased in all groups but patients with subtype C viruses had the largest reduction of sCD27 from baseline. The data indicate that a similar immune activation profile is present in patients infected with HIV-1 subtypes A, B, and D and that in presence of successful ART these subtypes respond similarly in terms of immune activation. Intriguingly, subtype C infection seems to be associated with higher levels of plasma sCD27, suggesting that HIV-1 genetic subtype C may have a different impact on disease outcome and response to therapy.

  15. Manganese-enhanced magnetic resonance imaging for mapping of whole brain activity patterns associated with the intake of snack food in ad libitum fed rats.

    PubMed

    Hoch, Tobias; Kreitz, Silke; Gaffling, Simone; Pischetsrieder, Monika; Hess, Andreas

    2013-01-01

    Non-homeostatic hyperphagia, which is a major contributor to obesity-related hyperalimentation, is associated with the diet's molecular composition influencing, for example, the energy content. Thus, specific food items such as snack food may induce food intake independent from the state of satiety. To elucidate mechanisms how snack food may induce non-homeostatic food intake, it was tested if manganese-enhanced magnetic resonance imaging (MEMRI) was suitable for mapping the whole brain activity related to standard and snack food intake under normal behavioral situation. Application of the MnCl2 solution by osmotic pumps ensured that food intake was not significantly affected by the treatment. After z-score normalization and a non-affine three-dimensional registration to a rat brain atlas, significantly different grey values of 80 predefined brain structures were recorded in ad libitum fed rats after the intake of potato chips compared to standard chow at the group level. Ten of these areas had previously been connected to food intake, in particular to hyperphagia (e.g., dorsomedial hypothalamus or the anterior paraventricular thalamic nucleus) or to the satiety system (e.g., arcuate hypothalamic nucleus or solitary tract); 27 areas were related to reward/addiction including the core and shell of the nucleus accumbens, the ventral pallidum and the ventral striatum (caudate and putamen). Eleven areas associated to sleep displayed significantly reduced Mn2+ -accumulation and six areas related to locomotor activity showed significantly increased Mn2+ -accumulation after the intake of potato chips. The latter changes were associated with an observed significantly higher locomotor activity. Osmotic pump-assisted MEMRI proved to be a promising technique for functional mapping of whole brain activity patterns associated to nutritional intake under normal behavior. PMID:23408973

  16. Second-generation sulfonamide inhibitors of D-glutamic acid-adding enzyme: activity optimisation with conformationally rigid analogues of D-glutamic acid.

    PubMed

    Sosič, Izidor; Barreteau, Hélène; Simčič, Mihael; Sink, Roman; Cesar, Jožko; Zega, Anamarija; Grdadolnik, Simona Golič; Contreras-Martel, Carlos; Dessen, Andréa; Amoroso, Ana; Joris, Bernard; Blanot, Didier; Gobec, Stanislav

    2011-07-01

    D-Glutamic acid-adding enzyme (MurD) catalyses the essential addition of d-glutamic acid to the cytoplasmic peptidoglycan precursor UDP-N-acetylmuramoyl-l-alanine, and as such it represents an important antibacterial drug-discovery target enzyme. Based on a series of naphthalene-N-sulfonyl-d-Glu derivatives synthesised recently, we synthesised two series of new, optimised sulfonamide inhibitors of MurD that incorporate rigidified mimetics of d-Glu. The compounds that contained either constrained d-Glu or related rigid d-Glu mimetics showed significantly better inhibitory activities than the parent compounds, thereby confirming the advantage of molecular rigidisation in the design of MurD inhibitors. The binding modes of the best inhibitors were examined with high-resolution NMR spectroscopy and X-ray crystallography. We have solved a new crystal structure of the complex of MurD with an inhibitor bearing a 4-aminocyclohexane-1,3-dicarboxyl moiety. These data provide an additional step towards the development of sulfonamide inhibitors with potential antibacterial activities. PMID:21524830

  17. Development of budesonide nanocluster dry powder aerosols: preformulation.

    PubMed

    El-Gendy, Nashwa; Selvam, Parthiban; Soni, Pravin; Berkland, Cory

    2012-09-01

    Wet milling was previously demonstrated as a simple process for producing agglomerates of budesonide nanoparticles (also known as NanoClusters) for use in dry powder aerosol formulation. The resulting budesonide NanoCluster powders exhibited a large emitted fraction and a high fine particle fraction (FPF) from a Monodose® dry powder inhaler. In this work, excipients were added premilling or postmilling and the performance of budesonide NanoCluster dry powders was investigated. Sodium chloride, Pluronic®, or ethanol was added prior to milling due to their ability to modify surface tension or ionic strength and thereby affect the attrition/agglomeration process. Lactose or l-leucine was added after milling because these are known to modify powder flow and dispersion. The chemical stability of budesonide was maintained in all cases, but the physical aerosol properties changed substantially with the addition of excipients. In all cases, the addition of excipients led to an increase in the size of the budesonide NanoClusters and tended to reduce the emitted fraction and FPF. Titrating excipients may provide a means to discretely modify the aerosol properties of budesonide NanoClusters but did not match the performance of excipient-free NanoCluster powder.

  18. Physicochemical and Sensory Properties of Appenzeller Cheese Supplemented with Shrimp Powder

    PubMed Central

    Choi, Hee-Young; Kim, Kyoung-Hee; Chun, Soon-Sil

    2015-01-01

    The effects of adding shrimp (Periclimenes imperator) powder to Appenzeller cheese on quality and characteristics during ripening were investigated. Cheese samples were prepared containing 1.0%, 2.0%, and 3.0% shrimp powder. Changes in the lactic acid bacterial populations, pH, water-soluble nitrogen concentrations, consumer acceptability, colour and texture were monitored during ripening. The addition of shrimp powder did not affect the appearance or consumer sensory characteristics of the cheeses. Likewise, cheese cohesiveness, fracturability, and springiness were not significantly altered. It was concluded that the quality of the Appenzeller cheese was not affected by adding shrimp powder. PMID:26761833

  19. [Determination of the artificial bezoar powder in bezoar powder by near-infrared spectrometry and support vector machine].

    PubMed

    Ma, Qun; Hao, Gui-qi; Qiao, Yan-jiang; Zhang, Zhuo-yong; Zhang, Xiao-fang

    2006-10-01

    A method for determining the artificial bezoar powder in bezoar powder using near-infrared (NIR) diffuse reflectance spectrometry was proposed in the present paper. The method was based on support vector machine (SVM). The calibration set was set up by adding unequal artificial bezoar powder to the bezoar powder (content range: 0%-100% ) and collecting the NIR spectrum of the samples in the wave number range of 4000-10000 cm(-1). The processing algorithm was wavelet transform with first and second derivatives. A mathematical model with support vector machine was established. The model was checked with leave one method. The sum of the square of the relative prediction error was 0.00135. This method is reliable and can be used to control the quality of bezoar powder.

  20. Study of a large scale powdered activated carbon pilot: Removals of a wide range of emerging and priority micropollutants from wastewater treatment plant effluents.

    PubMed

    Mailler, R; Gasperi, J; Coquet, Y; Deshayes, S; Zedek, S; Cren-Olivé, C; Cartiser, N; Eudes, V; Bressy, A; Caupos, E; Moilleron, R; Chebbo, G; Rocher, V

    2015-04-01

    The efficacy of a fluidized powdered activated carbon (PAC) pilot (CarboPlus(®)) was studied in both nominal (total nitrification + post denitrification) and degraded (partial nitrification + no denitrification) configuration of the Seine Centre WWTP (Colombes, France). In addition to conventional wastewater parameters 54 pharmaceuticals and hormones (PhPHs) and 59 other emerging pollutants were monitored in influents and effluents of the pilot. Thus, the impacts of the WWTP configuration, the process operation and the physico-chemical properties of the studied compounds were assessed in this article. Among the 26 PhPHs quantified in nominal WWTP configuration influents, 8 have high dissolved concentrations (>100 ng/L), 11 have an intermediary concentration (10-100 ng/L) and 7 are quantified below 10 ng/L. Sulfamethoxazole is predominant (about 30% of the sum of the PhPHs). Overall, 6 PhPHs are poorly to moderately removed (<60%), such as ibuprofen, paracetamol or estrone, while 9 are very well removed (>80%), i.e. beta blockers, carbamazepine or trimethoprim, and 11 are well eliminated (60-80%), i.e. diclofenac, naproxen or sulfamethoxazole. In degraded WWTP configuration, higher levels of organic matter and higher concentrations of most pollutants are observed. Consequently, most PhPHs are substantially less removed in percentages but the removed flux is higher. Thus, the PAC dose required to achieve a given removal percentage is higher in degraded WWTP configuration. For the other micropollutants (34 quantified), artificial sweeteners and phthalates are found at particularly high concentrations in degraded WWTP configuration influents, up to μg/L range. Only pesticides, bisphenol A and parabens are largely eliminated (50-95%), while perfluorinated acids, PAHs, triclosan and sweeteners are not or weakly removed (<50%). The remaining compounds exhibit a very variable fate from campaign to campaign. The fresh PAC dose was identified as the most influencing

  1. Study of a large scale powdered activated carbon pilot: Removals of a wide range of emerging and priority micropollutants from wastewater treatment plant effluents.

    PubMed

    Mailler, R; Gasperi, J; Coquet, Y; Deshayes, S; Zedek, S; Cren-Olivé, C; Cartiser, N; Eudes, V; Bressy, A; Caupos, E; Moilleron, R; Chebbo, G; Rocher, V

    2015-04-01

    The efficacy of a fluidized powdered activated carbon (PAC) pilot (CarboPlus(®)) was studied in both nominal (total nitrification + post denitrification) and degraded (partial nitrification + no denitrification) configuration of the Seine Centre WWTP (Colombes, France). In addition to conventional wastewater parameters 54 pharmaceuticals and hormones (PhPHs) and 59 other emerging pollutants were monitored in influents and effluents of the pilot. Thus, the impacts of the WWTP configuration, the process operation and the physico-chemical properties of the studied compounds were assessed in this article. Among the 26 PhPHs quantified in nominal WWTP configuration influents, 8 have high dissolved concentrations (>100 ng/L), 11 have an intermediary concentration (10-100 ng/L) and 7 are quantified below 10 ng/L. Sulfamethoxazole is predominant (about 30% of the sum of the PhPHs). Overall, 6 PhPHs are poorly to moderately removed (<60%), such as ibuprofen, paracetamol or estrone, while 9 are very well removed (>80%), i.e. beta blockers, carbamazepine or trimethoprim, and 11 are well eliminated (60-80%), i.e. diclofenac, naproxen or sulfamethoxazole. In degraded WWTP configuration, higher levels of organic matter and higher concentrations of most pollutants are observed. Consequently, most PhPHs are substantially less removed in percentages but the removed flux is higher. Thus, the PAC dose required to achieve a given removal percentage is higher in degraded WWTP configuration. For the other micropollutants (34 quantified), artificial sweeteners and phthalates are found at particularly high concentrations in degraded WWTP configuration influents, up to μg/L range. Only pesticides, bisphenol A and parabens are largely eliminated (50-95%), while perfluorinated acids, PAHs, triclosan and sweeteners are not or weakly removed (<50%). The remaining compounds exhibit a very variable fate from campaign to campaign. The fresh PAC dose was identified as the most influencing

  2. Coseismic uplift and fault model of marine active faults in 1729 AD revealed by fossilized intertidal sessile organisms along the northern coast of the Noto Peninsula, central Japan

    NASA Astrophysics Data System (ADS)

    Hamada, M.; Hiramatsu, Y.; Oda, M.; Yamaguchi, H.

    2015-12-01

    The Noto Peninsula is located in the backarc region of southwest Japan and is characterized by geomorphologic features formed by active tectonics and glacial eustasy through the Quaternary. Pleistocene marine terraces along the northern coast of the Noto Peninsula indicate uplift in the coastal area through the late Quaternary (Ota and Hirakawa, 1979). Recently, an active fault zone on the seafloor off the coast was found and was divided into four segments, Monzen-oki, Saruyama-oki, Wajima-oki, and Suzu-oki, from west to east (Inoue and Okamura, 2010). We investigated vertical displacement along the coast using intertidal sessile organisms at nine sites on the rocky coast. We measured the height of fossilized Pomatoleios kraussii by GPS surveying together with a sea-level change curve, and dated them using the AMS 14C method. The vertical displacements and dates at the sites implied that coastal uplift occurred along 20 km of coastline, corresponding to the Wajima-oki segment zone, and most likely between 1600 and 1800 AD. This is coincident with seismic damage in this area in 1729 AD recorded in historical documents. We constructed a fault model with three rectangular faults in a homogeneous elastic half-space and estimated the optimal net slip and rake by a non-linear inversion method (Matsu'ura and Hasegawa, 1987). The best fit to the estimated vertical displacements is provided by a net slip of 1.8 m with a rake of 90° for the western fault plane and a net slip of 0.6 m with a rake of 90° for the center and the eastern fault planes. The moment magnitude (Mw) calculated from these parameters with a rigidity of 30 GPa is 6.6. We compared the elevation distribution of the former shorelines based on coastal terraces and the 1729 earthquake uplifts. Assuming that the coastal uplift is caused by the cumulative crustal deformation produced by the same size event as the 1729 earthquake, the average recurrence interval of the events is estimated to be 1700 years.

  3. Does Increased Exercise or Physical Activity Alter Ad-Libitum Daily Energy Intake or Macronutrient Composition in Healthy Adults? A Systematic Review

    PubMed Central

    Donnelly, Joseph E.; Herrmann, Stephen D.; Lambourne, Kate; Szabo, Amanda N.; Honas, Jeffery J.; Washburn, Richard A.

    2014-01-01

    Background The magnitude of the negative energy balance induced by exercise may be reduced due to compensatory increases in energy intake. Objective To address the question: Does increased exercise or physical activity alter ad-libitum daily energy intake or macronutrient composition in healthy adults? Data Sources PubMed and Embase were searched (January 1990–January 2013) for studies that presented data on energy and/or macronutrient intake by level of exercise, physical activity or change in response to exercise. Ninety-nine articles (103 studies) were included. Study Eligibility Criteria Primary source articles published in English in peer-reviewed journals. Articles that presented data on energy and/or macronutrient intake by level of exercise or physical activity or changes in energy or macronutrient intake in response to acute exercise or exercise training in healthy (non-athlete) adults (mean age 18–64 years). Study Appraisal and Synthesis Methods Articles were grouped by study design: cross-sectional, acute/short term, non-randomized, and randomized trials. Considerable heterogeneity existed within study groups for several important study parameters, therefore a meta-analysis was considered inappropriate. Results were synthesized and presented by study design. Results No effect of physical activity, exercise or exercise training on energy intake was shown in 59% of cross-sectional studies (n = 17), 69% of acute (n = 40), 50% of short-term (n = 10), 92% of non-randomized (n = 12) and 75% of randomized trials (n = 24). Ninety-four percent of acute, 57% of short-term, 100% of non-randomized and 74% of randomized trials found no effect of exercise on macronutrient intake. Forty-six percent of cross-sectional trials found lower fat intake with increased physical activity. Limitations The literature is limited by the lack of adequately powered trials of sufficient duration, which have prescribed and measured exercise energy expenditure

  4. Physicochemical and nutritional qualities of grape pomace powder-fortified semi-hard cheeses.

    PubMed

    Marchiani, Roberta; Bertolino, Marta; Ghirardello, Daniela; McSweeney, Paul L H; Zeppa, Giuseppe

    2016-03-01

    Powders obtained from three grape pomaces (Barbera, Chardonnay before distillation, Chardonnay after distillation) were added at two concentration levels (0.8 and 1.6 % w/w) into semi-hard and hard cheeses (Italian Toma-like and Cheddar, respectively) to increase their polyphenol content. Effects on physicochemical characteristics, total phenolic content (TPC), radical scavenging activity (RSA), proteolysis, organic acids content, starter and non-starter bacteria were evaluated during ripening. The amount and the type of powder used did not significantly affect the physicochemical parameters of cheese with the exception of pH their values. Italian Toma-like and Cheddar cheeses fortified with Chardonnay after distillation powder showed at the end of ripening (30 days and 120 days respectively) the highest TPC and RSA values. Proteolysis and microbial counts did not show statistically significant differences between fortified and control cheeses. This study demonstrated that grape pomace powder can be a functional ingredient to increase TPC and RSA in consumers' diets and the addition of this by-product to cheese is an environmentally friendly way to manage winemaking wastes. PMID:27570284

  5. Structural changes during milling of aluminum oxide powders

    NASA Technical Reports Server (NTRS)

    Ziepler, G.

    1984-01-01

    The mechanical activation of four fused corundum powders and a calcined Al2O3 powder was studied. The milled powders were characterized by their structural properties, crystallite size, and lattice distortions. Structural changes during milling, detected by X-ray line broadening analysis, gave information about the enhanced activity of the powders caused by the lattice distortions and by the decreasing crystallite size during milling. The structural changes during milling, under the same milling conditions, can be quite different for the same ceramic material, but with different characteristics in the as received state.

  6. Ultrafine hydrogen storage powders

    DOEpatents

    Anderson, Iver E.; Ellis, Timothy W.; Pecharsky, Vitalij K.; Ting, Jason; Terpstra, Robert; Bowman, Robert C.; Witham, Charles K.; Fultz, Brent T.; Bugga, Ratnakumar V.

    2000-06-13

    A method of making hydrogen storage powder resistant to fracture in service involves forming a melt having the appropriate composition for the hydrogen storage material, such, for example, LaNi.sub.5 and other AB.sub.5 type materials and AB.sub.5+x materials, where x is from about -2.5 to about +2.5, including x=0, and the melt is gas atomized under conditions of melt temperature and atomizing gas pressure to form generally spherical powder particles. The hydrogen storage powder exhibits improved chemcial homogeneity as a result of rapid solidfication from the melt and small particle size that is more resistant to microcracking during hydrogen absorption/desorption cycling. A hydrogen storage component, such as an electrode for a battery or electrochemical fuel cell, made from the gas atomized hydrogen storage material is resistant to hydrogen degradation upon hydrogen absorption/desorption that occurs for example, during charging/discharging of a battery. Such hydrogen storage components can be made by consolidating and optionally sintering the gas atomized hydrogen storage powder or alternately by shaping the gas atomized powder and a suitable binder to a desired configuration in a mold or die.

  7. Agricultural Education: Value Adding.

    ERIC Educational Resources Information Center

    Riesenberg, Lou E.; And Others

    1989-01-01

    This issue develops the theme of "Agricultural Education--Value Adding." The concept value adding has been a staple in the world of agricultural business for describing adding value to a commodity that would profit the producer and the local community. Agricultural education should add value to individuals and society to justify agricultural…

  8. Characterization of reactive impurities in methanol, ethanol, and 2-propanol by monitoring the activities of added ionic probes with ion selective electrodes

    SciTech Connect

    Deshmukh, B.K.; Coetzee, J.F.

    1984-11-01

    The presence of reactive impurities compromises many important applications of solvents. It is shown that a wide variety of impurities can be detected and determined by adding such highly reactive probes as hydrogen, methoxide, copper(II), mercury(II), and fluoride ions and monitoring their activities over an appropriately wide range with the corresponding ion selective electrodes. The results for the alcohols show that typical reagent grades of these solvents contain amines at the 10/sup -5/ - 10/sup -4/ M (1-10 ppm) level as well as other reactive impurities. This approach is applicable to most polar solvents. It has the overriding merits that it detects impurities on the basis on their reactivities (rather than only their concentrations) and that its lower detection limit is self-adjusting in that it is lowest (most favorable) in the very solvents in which impurities are most harmful, i.e., relatively inert solvent. In such solvents, its lower detection limit can be much lower than that attainable with gas chromatography.

  9. CTAB-assisted synthesis of mesoporous F-N-codoped TiO{sub 2} powders with high visible-light-driven catalytic activity and adsorption capacity

    SciTech Connect

    Xie Yi Zhao Xiujian Li Yuanzhi; Zhao Qingnan; Zhou Xuedong; Yuan Qihua

    2008-08-15

    This article describes the preparation of mesoporous rod-like F-N-codoped TiO{sub 2} powder photocatalysts with anatase phase via a sol-gel route at the temperature of 373 K, using cetyltrimethyl ammonium bromide (CTAB) as surfactant. The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible diffuse reflectance spectra (UV-vis DRS). The results showed that the photocatalysts possessed a homogeneous pore diameter and a high surface area of 106.3-160.7 m{sup 3} g{sup -1}. The increasing CTAB reactive concentration extended the visible-light absorption up to 600 nm. The F-N-codoped TiO{sub 2} powders exhibited significant higher adsorption capacity for methyl orange (MO) than that of Degussa P25 and showed more than 6 times higher visible-light-induced catalytic degradation for MO than that of P25. - Graphical abstract: The introduction of surfactant CTAB not only extended the visible light absorption of mesoporous F-N-codoped TiO{sub 2} up to 600 nm but also significantly enhanced the adsorption capacity and visible-light-induced degradation for methyl orange. Mesoporous rod-like F-N-codoped TiO{sub 2} powder photocatalysts were synthesized via a sol-gel route at low temperature of 373 K.

  10. Iowa Powder Atomization Technologies

    ScienceCinema

    None

    2016-07-12

    The same atomization effect seen in a fuel injector is being applied to titanium metal resulting in fine titanium powders that are less than half the width of a human hair. Titanium melts above 3,000°F and is highly corrosive therefore requiring specialized containers. The liquid titanium is poured through an Ames Laboratory - USDOE patented tube which is intended to increase the energy efficiency of the atomization process, which has the ability to dramatically decrease the cost of fine titanium powders. This novel process could open markets for green manufacturing of titanium components from jet engines to biomedical implants.

  11. Iowa Powder Atomization Technologies

    SciTech Connect

    2012-01-01

    The same atomization effect seen in a fuel injector is being applied to titanium metal resulting in fine titanium powders that are less than half the width of a human hair. Titanium melts above 3,000°F and is highly corrosive therefore requiring specialized containers. The liquid titanium is poured through an Ames Laboratory - USDOE patented tube which is intended to increase the energy efficiency of the atomization process, which has the ability to dramatically decrease the cost of fine titanium powders. This novel process could open markets for green manufacturing of titanium components from jet engines to biomedical implants.

  12. Powder towpreg process development

    NASA Technical Reports Server (NTRS)

    Baucom, Robert M.; Marchello, Joseph M.

    1991-01-01

    The process for dry powder impregnation of carbon fiber tows being developed at LaRC overcomes many of the difficulties associated with melt, solution, and slurry prepregging. In the process, fluidized powder is deposited on spread tow bundles and fused to the fibers by radiant heating. Impregnated tows have been produced for preform, weaving, and composite materials applications. Design and operating data correlations were developed for scale up of the process to commercial operation. Bench scale single tow experiments at tow speeds up to 50 cm/sec have demonstrated that the process can be controlled to produce weavable towpreg. Samples were woven and molded into preform material of good quality.

  13. On the relationship of inter-particle cohesiveness and bulk powder behavior: Flowability of pharmaceutical powders.

    PubMed

    Capece, Maxx; Silva, Karina Ruiz; Sunkara, Divya; Strong, John; Gao, Ping

    2016-09-10

    This study investigates the relationship between particle interactions dominated by the cohesive van der Waals force and powder flowability for materials commonly used by the pharmaceutical industry in oral solid dosage formulation. This study first sought to correlate the granular Bond number, defined as the ratio of the inter-particle cohesion force to particle weight, to the flow function coefficient, a metric commonly used to assess powder flowability. However, the granular Bond number which strictly quantifies inter-particle cohesiveness was found to correlate poorly with powder flowability due to the complexity associated with particle assemblies. To account for the multitude of interactions between particles of different sizes within a powder and to more precisely predict bulk powder behavior, a population-dependent granular Bond number was proposed. The population-dependent granular Bond number which explicitly accounts for particle size distribution and described herein as a quantification of powder cohesiveness (instead of inter-particle cohesiveness) was shown to correlate well with the flow function coefficient for a wide variety of materials including four active pharmaceutical ingredients (APIs) and fourteen common pharmaceutical excipients. Due to the success of the population-dependent granular Bond number, it was extended to predict the flowability of powder blends. This so-called population-dependent multi-component granular Bond number takes into account relevant material properties and particle interactions and was used to predict the flowability of 6-component powder blends containing acetaminophen as a model cohesive active pharmaceutical ingredient. Prediction of bulk powder behavior from individual material properties as accomplished here may be highly useful in formulation development.

  14. On the relationship of inter-particle cohesiveness and bulk powder behavior: Flowability of pharmaceutical powders.

    PubMed

    Capece, Maxx; Silva, Karina Ruiz; Sunkara, Divya; Strong, John; Gao, Ping

    2016-09-10

    This study investigates the relationship between particle interactions dominated by the cohesive van der Waals force and powder flowability for materials commonly used by the pharmaceutical industry in oral solid dosage formulation. This study first sought to correlate the granular Bond number, defined as the ratio of the inter-particle cohesion force to particle weight, to the flow function coefficient, a metric commonly used to assess powder flowability. However, the granular Bond number which strictly quantifies inter-particle cohesiveness was found to correlate poorly with powder flowability due to the complexity associated with particle assemblies. To account for the multitude of interactions between particles of different sizes within a powder and to more precisely predict bulk powder behavior, a population-dependent granular Bond number was proposed. The population-dependent granular Bond number which explicitly accounts for particle size distribution and described herein as a quantification of powder cohesiveness (instead of inter-particle cohesiveness) was shown to correlate well with the flow function coefficient for a wide variety of materials including four active pharmaceutical ingredients (APIs) and fourteen common pharmaceutical excipients. Due to the success of the population-dependent granular Bond number, it was extended to predict the flowability of powder blends. This so-called population-dependent multi-component granular Bond number takes into account relevant material properties and particle interactions and was used to predict the flowability of 6-component powder blends containing acetaminophen as a model cohesive active pharmaceutical ingredient. Prediction of bulk powder behavior from individual material properties as accomplished here may be highly useful in formulation development. PMID:27353729

  15. The pharmacological profile of 2-(8-methyl-10,11-dihydro-11-oxodibenz[b,f]oxepin-2-yl)propionic acid (AD-1590), a new non-steroidal anti-inflammatory agent with potent antipyretic activity.

    PubMed

    Nakamura, H; Yokoyama, Y; Motoyoshi, S; Ishii, K; Imazu, C; Seto, Y; Kadokawa, T; Shimizu, M

    1983-01-01

    Anti-inflammatory, analgesic, antipyretic and gastrointestinal ulcerogenic activities of 2-(8-methyl-10,11-dihydro-11-oxodibenz(b,f]oxepin-2-yl)propionic acid (AD-1590), a new non-steroidal anti-inflammatory drug, were compared with indomethacin (INN: indomethacin) and other non-steroidal anti-inflammatory drugs (NSAID) in experimental animals. AD-1590 showed the potent inhibitory activity on acute and subacute inflammation such as carrageenin hind paw edema (oral ED50 = 1.35 mg/kg), acetic acid-induced increased vascular permeability (0.205 mg/kg), UV-erythema (0.295 mg/kg) and felt pellet-induced granuloma formation (1.7 mg/kg), and its potency was on the whole 2 to 3 times that of indomethacin. Oral analgesic ED50-values of AD-1590 were 0.245, 8.32 and 13.9 mg/kg in the writhing tests, and 2.45 mg/kg in the silver nitrate-induced arthritic pain test. Analgesic potency of AD-1590 was on the whole comparable to that of indomethacin. Against the pyrexia caused by two kinds of pyrogens (yeast and adjuvant), AD-1590 exerted a strong antipyretic action at oral doses as low as 0.02 to 0.1 mg/kg, and its potency (ED50 equal 0.0210 and 0.0406 mg/kg) was 8.7 to 11 times that of indomethacin. , AD-1590 displayed the antipyretic activity at low doses which were widely different from its anti-inflammatory and analgesic effective dose. The body temperature was not affected by 20 mg/kg p.o. of AD-1590 in the afebrile animals. AD-1590 was the strongest antipyretic drug among 10 NSAID tested. In rats, AD-1590 produced gastrointestinal ulcer similar to indomethacin, and its gastric ulcerogenicity (SUD50 equal 13.8 mg/kg p.o.) was about one-half that of indomethacin. The activity of AD-1590 in the fecal occult bleeding test in beagle dogs was weaker than that of indomethacin. The potency of AD-1590 (IC50 equal 0.78 mumol/l) as a prostaglandin synthetase inhibitor was about 2.7 times that of indomethacin in the in vitro test. The safety index (SUD50/ED50) of AD-1590 was larger than

  16. Electrically conductive ceramic powders

    NASA Astrophysics Data System (ADS)

    Lu, Yanxia

    1999-11-01

    Electrically conductive ceramic powders were investigated in this project. There are three ways to produce those materials. The first is doping alkali metal into the titanium dioxides in an inert or reducing atmosphere. The second is reducing un-doped titanium dioxide, forming a non-stoichiometric composition in a hydrogen atmosphere. The third is to coat a conductive layer, reduced titanium dioxide, on an insulating core such as alumina. Highly conductive powders have been produced by all these processes. The conductivity of powder compacts ranged between 10-2 and 10° S/cm. A novel doping process was developed. All samples were doped by a solid-vapor reaction instead of a solid state reaction. Titanium dioxide was doped with alkali metals such as Na or Li in this study. The alkali metal atom contributes an electron to the host material (TiO2), which then creates Ti 3+ ion. The conductivity was enhanced by creating the donor level due to the presence of these Ti3+ ions. The conductivity of those alkali doped titanium oxides was dependent on the doping level and charge mobility. Non-stoichiometric titanium oxides were produced by reduction of titanium dioxide in a hydrogen atmosphere at 800°C to 1000°C for 2 to 6 hours. The reduced titanium oxides showed better stability with respect to conductivity at ambient condition when compared with the Na or Li doped samples. Conductive coatings were prepared by coating titanium precursors on insulating core materials like SiO2, Al2O3 or mica. The titania coating was made by hydrolysis of titanyl sulfate (TiOSO 4) followed by a reduction procedure to form reduced titanium oxide. The reduced titanium oxides are highly conductive. A uniform coating of titanium oxides on alumina cores was successfully produced. The conductivity of coated powder composites was a function of coating quantity and hydrolysis reaction temperature. The conductivity of the powder as a function of structure, composition, temperature, frequency and

  17. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1992-04-21

    A free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7 [times] 10[sup [minus]3] to about 7 [times] 10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 9 figs.

  18. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1993-10-19

    Free flowing, conformable powder-like mix of silica particles and a phase change material (pcm) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 10 figures.

  19. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1993-05-18

    Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the p.c.m. must be added to the silica in an amount of 80 wt. % or less p.c.m. per combined weight of silica and p.c.m. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a p.c.m. material. The silica-p.c.m. mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

  20. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, I.O.

    1994-02-01

    Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 2 figures.

  1. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1993-01-01

    Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

  2. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1994-01-01

    Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

  3. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1992-01-01

    Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

  4. Dry powder mixes comprising phase change materials

    DOEpatents

    Salyer, Ival O.

    1993-01-01

    Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garmets, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

  5. Adding flavor to AdS4/CFT3

    NASA Astrophysics Data System (ADS)

    Ammon, Martin; Erdmenger, Johanna; Meyer, René; O'Bannon, Andy; Wrase, Timm

    2009-11-01

    Aharony, Bergman, Jafferis, and Maldacena have proposed that the low-energy description of multiple M2-branes at a Bbb C4/Bbb Zk singularity is a (2+1)-dimensional Script N = 6 supersymmetric U(Nc) × U(Nc) Chern-Simons matter theory, the ABJM theory. In the large-Nc limit, its holographic dual is supergravity in AdS4 × S7/Bbb Zk. We study various ways to add fields that transform in the fundamental representation of the gauge groups, i.e. flavor fields, to the ABJM theory. We work in a probe limit and perform analyses in both the supergravity and field theory descriptions. In the supergravity description we find a large class of supersymmetric embeddings of probe flavor branes. In the field theory description, we present a general method to determine the couplings of the flavor fields to the fields of the ABJM theory. We then study four examples in detail: codimension-zero Script N = 3 supersymmetric flavor, described in supergravity by Kaluza-Klein monopoles or D6-branes; codimension-one Script N = (0,6) supersymmetric chiral flavor, described by D8-branes; codimension-one Script N = (3,3) supersymmetric non-chiral flavor, described by M5/D4-branes; codimension-two Script N = 4 supersymmetric flavor, described by M2/D2-branes. Finally we discuss special physical equivalences between brane embeddings in M-theory, and their interpretation in the field theory description.

  6. Method for synthesizing powder materials

    DOEpatents

    Buss, R.J.; Ho, P.

    1988-01-21

    A method for synthesizing ultrafine powder materials, for example, ceramic and metal powders, comprises admitting gaseous reactants from which the powder material is to be formed into a vacuum reaction chamber maintained at a pressure less than atmospheric and at a temperature less than about 400/degree/K (127/degree/C). The gaseous reactants are directed through a glow discharge provided in the vacuum reaction chamber to form the ultrafine powder material. 1 fig.

  7. Twistor methods for AdS5

    NASA Astrophysics Data System (ADS)

    Adamo, Tim; Skinner, David; Williams, Jack

    2016-08-01

    We consider the application of twistor theory to five-dimensional anti-de Sitter space. The twistor space of AdS5 is the same as the ambitwistor space of the four-dimensional conformal boundary; the geometry of this correspondence is reviewed for both the bulk and boundary. A Penrose transform allows us to describe free bulk fields, with or without mass, in terms of data on twistor space. Explicit representatives for the bulk-to-boundary propagators of scalars and spinors are constructed, along with twistor action functionals for the free theories. Evaluating these twistor actions on bulk-to-boundary propagators is shown to produce the correct two-point functions.

  8. AdS3: the NHEK generation

    NASA Astrophysics Data System (ADS)

    Bena, Iosif; Heurtier, Lucien; Puhm, Andrea

    2016-05-01

    It was argued in [1] that the five-dimensional near-horizon extremal Kerr (NHEK) geometry can be embedded in String Theory as the infrared region of an infinite family of non-supersymmetric geometries that have D1, D5, momentum and KK monopole charges. We show that there exists a method to embed these geometries into asymptotically- {AdS}_3× {S}^3/{{Z}}_N solutions, and hence to obtain infinite families of flows whose infrared is NHEK. This indicates that the CFT dual to the NHEK geometry is the IR fixed point of a Renormalization Group flow from a known local UV CFT and opens the door to its explicit construction.

  9. 21 CFR 520.110 - Apramycin sulfate soluble powder.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... sulfate soluble powder. (a) Specifications. A water soluble powder used to make a medicated drinking water containing apramycin sulfate equivalent to 0.375 gram of apramycin activity per gallon of drinking water. (b...) caused by strains of E. coli sensitive to apramycin. (2) It is administered for 7 days in drinking...

  10. 21 CFR 520.110 - Apramycin sulfate soluble powder.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... sulfate soluble powder. (a) Specifications. A water soluble powder used to make a medicated drinking water containing apramycin sulfate equivalent to 0.375 gram of apramycin activity per gallon of drinking water. (b...) caused by strains of E. coli sensitive to apramycin. (2) It is administered for 7 days in drinking...

  11. 21 CFR 520.110 - Apramycin sulfate soluble powder.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... sulfate soluble powder. (a) Specifications. A water soluble powder used to make a medicated drinking water containing apramycin sulfate equivalent to 0.375 gram of apramycin activity per gallon of drinking water. (b...) caused by strains of E. coli sensitive to apramycin. (2) It is administered for 7 days in drinking...

  12. 21 CFR 520.110 - Apramycin sulfate soluble powder.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... sulfate soluble powder. (a) Specifications. A water soluble powder used to make a medicated drinking water containing apramycin sulfate equivalent to 0.375 gram of apramycin activity per gallon of drinking water. (b...) caused by strains of E. coli sensitive to apramycin. (2) It is administered for 7 days in drinking...

  13. Effect of added carbohydrates on glycemic and insulin responses to children’s milk products.

    PubMed

    Brand-Miller, Jennie; Atkinson, Fiona; Rowan, Angela

    2013-01-01

    Powdered milk products for children (Growing Up Milk Powders or GUMPs) containing added carbohydrates such as glucose and sucrose are now well established in parts of Asia. We surveyed GUMPs in Malaysia and Indonesia to determine the content of added carbohydrates. The ingredient lists and nutrition information panels were used to calculate the percentage of declared carbohydrates contributed by added carbohydrates and a subset of seven products was tested for their glycemic index (GI) and insulin responses in healthy adults. The glycemic load for each product was calculated. In total, 58 products (n = 24 in Malaysia and n = 34 in Indonesia) were surveyed. Added carbohydrate content (excluding fibre) ranged from 0 to 21.5 g per serve. Milk powders without added sources of carbohydrate had similar GI values to standard liquid whole milk. Products containing maltodextrins, corn or glucose syrups increased the GI by more than 2-fold, and glycemic load (GL) by 7-fold compared to milk powders with no added carbohydrates. Insulin responses were significantly but not strongly correlated with glucose responses (r = 0.32, p < 0.006). Children's milk powders containing higher levels of added carbohydrate ingredients elicit higher glucose and insulin responses than liquid or powdered whole milk. PMID:23306187

  14. Shadows, currents, and AdS fields

    SciTech Connect

    Metsaev, R. R.

    2008-11-15

    Conformal totally symmetric arbitrary spin currents and shadow fields in flat space-time of dimension greater than or equal to four are studied. A gauge invariant formulation for such currents and shadow fields is developed. Gauge symmetries are realized by involving the Stueckelberg fields. A realization of global conformal boost symmetries is obtained. Gauge invariant differential constraints for currents and shadow fields are obtained. AdS/CFT correspondence for currents and shadow fields and the respective normalizable and non-normalizable solutions of massless totally symmetric arbitrary spin AdS fields are studied. The bulk fields are considered in a modified de Donder gauge that leads to decoupled equations of motion. We demonstrate that leftover on shell gauge symmetries of bulk fields correspond to gauge symmetries of boundary currents and shadow fields, while the modified de Donder gauge conditions for bulk fields correspond to differential constraints for boundary conformal currents and shadow fields. Breaking conformal symmetries, we find interrelations between the gauge invariant formulation of the currents and shadow fields, and the gauge invariant formulation of massive fields.

  15. Vacuum powder injector and method of impregnating fiber with powder

    NASA Technical Reports Server (NTRS)

    Working, Dennis C. (Inventor)

    1993-01-01

    A method and apparatus uniformly impregnate stranded material with dry powder such as low solubility, high melt flow polymer powder to produce, for example, composite prepregs. The stranded material is expanded in an impregnation chamber by an influx of air so that the powder, which may enter through the same inlet as the air, penetrates to the center of the stranded material. The stranded material then is contracted for holding the powder therein. The stranded material and powder may be pulled through the impregnation chamber in the same direction by vacuum. Larger particles of powder which do not fully penetrate the stranded material may be combed into the stranded material and powder which does not impregnate the stranded material may be collected and reused.

  16. Dispersant for aqueous slurry of coal powder

    SciTech Connect

    Moriyama, N.; Watanabe, S.; Yamamura, M.

    1982-05-18

    A dispersant for forming an aqueous slurry of coal powder having a good flowability, which comprises as the active ingredient at least one member selected from sulfonation products of polycyclic aromatic compounds which may have a hydrocarbon group as a substituent, salts thereof and formaldehyde condensates thereof.

  17. Particle Morphology Effects on Flow Characteristics of PS304 Plasma Spray Coating Feedstock Powder Blend

    NASA Technical Reports Server (NTRS)

    Stanford, Malcolm K.; DellaCorte, Christopher; Eylon, Daniel

    2002-01-01

    The effects of BaF2-CaF 2 particle morphology on PS304 feedstock powder flow ability have been investigated. BaF2-CaF2 eutectic powders were fabricated by comminution (angular) and by gas atomization (spherical). The fluoride powders were added incrementally to the other powder constituents of the PS304 feedstock: nichrome, chromia, and silver powders. A linear relationship between flow time and concentration of BaF2-CaF2 powder was found. Flow of the powder blend with spherical BaF2-CaF2 was better than the angular BaF2-CaF2. Flow ability of the powder blend with angular fluorides decreased linearly with increasing fluoride concentration. Flow of the powder blend with spherical fluorides was independent of fluoride concentration. Results suggest that for this material blend, particle morphology plays a significant role in powder blend flow behavior, offering potential methods to improve powder flow ability and enhance the commercial potential. These findings may have applicability to other difficult-to-flow powders such as cohesive ceramics.

  18. Processing polymeric powders

    NASA Technical Reports Server (NTRS)

    Throne, James L.

    1989-01-01

    The concept of uniformly and continuously depositing and sinter-fusing nominal 0.1 to 40 microns dimensioned electrostatically charged polymer powder particles onto essentially uniformly spread 5 to 20 micron grounded continuous fiber tow to produce a respoolable thermoplastic composite two-preg was formulated at NASA Langley. The process was reduced to practice under a NASA grant at the University of Akron this spring. The production of tow-preg is called phase 1. The production of ultrafine polymer powders from 5 to 10 percent (wt) polymer solids in solvent is considered. This is phase 0 and is discussed. The production of unitape from multi tow-pregs was also considered. This is phase 2 and is also discussed. And another approach to phase 1, also proposed last summer, was scoped. This is phase 1A and is also discussed.

  19. Advanced powder processing

    SciTech Connect

    Janney, M.A.

    1997-04-01

    Gelcasting is an advanced powder forming process. It is most commonly used to form ceramic or metal powders into complex, near-net shapes. Turbine rotors, gears, nozzles, and crucibles have been successfully gelcast in silicon nitride, alumina, nickel-based superalloy, and several steels. Gelcasting can also be used to make blanks that can be green machined to near-net shape and then high fired. Green machining has been successfully applied to both ceramic and metal gelcast blanks. Recently, the authors have used gelcasting to make tooling for metal casting applications. Most of the work has centered on H13 tool steel. They have demonstrated an ability to gelcast and sinter H13 to near net shape for metal casting tooling. Also, blanks of H13 have been cast, green machined into complex shape, and fired. Issues associated with forming, binder burnout, and sintering are addressed.

  20. Qualitative tests for added coloring matter in meat products.

    PubMed

    McNeal, J E

    1976-05-01

    The rapid qualitative detection of coal tar dyes, chemicals added to color meat products, and some natural coloring materials was investigated through extraction and subsequent identification by spectrophotometric, paper chromatographic, and specific reaction techniques. These techniques will detect the presence of coal tar dyes, imidazole, histamine, histidine, cochineal, beet powder, annatto, alkanet, carotene, paprika, saffron, turmeric, and materials causing discoloration in meats.

  1. Preparation of superconductor precursor powders

    DOEpatents

    Bhattacharya, Raghunath

    1998-01-01

    A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic and/or reduced particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of all metals in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products.

  2. Silicon nitride/silicon carbide composite powders

    DOEpatents

    Dunmead, Stephen D.; Weimer, Alan W.; Carroll, Daniel F.; Eisman, Glenn A.; Cochran, Gene A.; Susnitzky, David W.; Beaman, Donald R.; Nilsen, Kevin J.

    1996-06-11

    Prepare silicon nitride-silicon carbide composite powders by carbothermal reduction of crystalline silica powder, carbon powder and, optionally, crystalline silicon nitride powder. The crystalline silicon carbide portion of the composite powders has a mean number diameter less than about 700 nanometers and contains nitrogen. The composite powders may be used to prepare sintered ceramic bodies and self-reinforced silicon nitride ceramic bodies.

  3. Removal of Carbamazepine from Water by a Novel TiO2–Coconut Shell Powder/UV Process: Composite Preparation and Photocatalytic Activity

    PubMed Central

    Khraisheh, Majeda; Kim, Jongkyu; Campos, Luiza; Al-Muhtaseb, Ala'a H.; Walker, Gavin M.; AlGhouti, Mohammad

    2013-01-01

    Abstract A novel TiO2–coconut shell powder (TCNSP) composite, prepared by the controlled sol-gel method with a subsequent heat treatment, was investigated as an innovative photocatalytic absorbent for the removal of carbamazepine (CBZ). CBZ is used worldwide as an antiepileptic drug, which has recently been recognized as an important organic pollutant increasingly found in wastewaters from urban areas and other aquatic environments. The granulation process was performed by using a semiautomated mass production line to produce sufficient quantities of TCNSP composites, possessing sufficient crush strength for commercialization. Physical properties of the TCNSP composite such as crystallinity, morphology, crush strength, and the Brunauer-Emmett-Teller (BET)–specific surface area were controlled by the mass ratio of titanium dioxide sol and coconut shell powder (CNSP). Calcination at 700°C produced anatase phase TiO2 in the TCNSP composites with a BET high surface area of 454 m2/g. Anatase crystallite size of the TCNSP composite increased from 2.37 to 15.11 nm with increasing calcination temperature from 500°C to 800°C. Calcinated TCNSP composites had higher CBZ removal efficiency (98%) than pure TiO2 (23%) and CNSP (34%) within a 40-min reaction time. Optimization of this innovative adsorption/photocatalytic process was obtained by a response surface methodology and a central composite design model, which indicated that this novel and sustainable technology was successful in removing CBZ from a solution. PMID:24065870

  4. Insecticidal activity of the granulosis virus in combination with neem products and talc powder against the potato tuberworm Phthorimaea operculella (Zeller) (Lepidoptera: Gelechiidae).

    PubMed

    Mascarin, G M; Delalibera, I

    2012-06-01

    The potato tuberworm Phthorimaea operculella (Zeller) is an important agricultural pest that causes significant economic losses to potato growers worldwide. The addition of an effective method of biological control for the potato tuberworm is greatly needed, and is currently unavailable in Brazil. The granulosis virus (Baculoviridae) is a promising biological control agent to protect post-harvest potatoes and in storage from the potato tuberworm. However, the control measure must be economically feasible. Liquid suspensions of a granulosis virus applied alone or in mixture with two commercial neem oil-based products (DalNeem™ and NeemAzal™), and a dry powder formulation of viral granules were evaluated for control of potato tuberworm larvae by treating potato tubers under laboratory conditions. High larval mortality (86.7%) was achieved when DalNeem and virus were applied together at 4 mg of azadirachtin/L and 10(4) occlusion bodies (OBs)/mL, respectively. This combination resulted in ≥50% efficacy in relation to their counterparts alone. Conversely, NeemAzal did not enhance virus effectiveness against larvae of the potato tuberworm. The talc-based virus formulation was used for dusting seed tubers at different concentrations and resulted in 100% larval mortality at 5 × 10(8) OBs/g. Formulated and unformulated virus provided 50% mortality at 166 OBs/g and at 5.0 × 10(5) OBs/mL, respectively. As a result, talc-based virus formulation had a better control efficiency on potato tuberworm than the aqueous virus suspension. The granulosis virus combined with DalNeem at low rates or formulated with talc powder is a viable option to control the potato tuberworm under storage conditions. PMID:23950047

  5. Suppression of protein phosphatase 2A activity enhances Ad5/F35 adenovirus transduction efficiency in normal human B lymphocytes and in Raji cells.

    PubMed

    Cayer, Marie-Pierre; Samson, Mélanie; Bertrand, Claudia; Dumont, Nellie; Drouin, Mathieu; Jung, Daniel

    2012-02-28

    Investigation of the molecular processes which control the development and function of lymphocytes is essential for our understanding of humoral immunity, as well as lymphocyte associated pathogenesis. Adenovirus-mediated gene transfer provided a powerful tool to investigate these processes. We have previously demonstrated that adenoviral vector Ad5/F35 transduces plasma cell lines at a higher efficiency than primary B cells, owing to differences in intracellular trafficking. Given that phosphatases are effectors of intracellular trafficking, here we have analyzed the effects of a panel of phosphatase inhibitors on Ad5/F35 transduction efficiency in B lymphocytes in the present study. FACS analysis was conducted to determine Ad5/F35-EYFP transduction efficiency in lymphoid cells, including human primary B cells, following serine/threonine phosphatase (PSP) inhibitor treatment. We further used confocal microscopy to analyze intracellular trafficking and fate of CY3 labeled Ad5/F35 vectors, in PSP treated lymphoid cell. Finally, we analyzed the MAPK pathway by Western blot in PSP treated cells. Adenoviral transduction efficiency was unresponsive to inhibition of PP1 whereas inhibition of PP2A by cantharidic acid, or PP1 and PP2A by okadaic acid, substantially increased transduction efficiency. Importantly, confocal microscopy analyses revealed that inhibition of PP2A shut down adenovirus recycling. Moreover, inhibition of PP2A resulted in increased phosphorylation of AKT, ERK1/2 and MEK1/2. Taken together, these results suggest that Ad5/F35 is more efficiently transduced in cells following PP2A inhibition. Our results are in agreement with reports indicating that PP2A is involved in the formation of recycling vesicles and might be of interest for gene therapy applications.

  6. ADS pilot program Plan

    NASA Technical Reports Server (NTRS)

    Clauson, J.; Heuser, J.

    1981-01-01

    The Applications Data Service (ADS) is a system based on an electronic data communications network which will permit scientists to share the data stored in data bases at universities and at government and private installations. It is designed to allow users to readily locate and access high quality, timely data from multiple sources. The ADS Pilot program objectives and the current plans for accomplishing those objectives are described.

  7. [Effect of air humidity on traditional Chinese medicine extract of spray drying process and prediction of its powder stability].

    PubMed

    He, Yan; Xie, Yin; Zheng, Long-jin; Liu, Wei; Rao, Xiao-yong; Luo, Xiao-jian

    2015-02-01

    In order to solve the adhesion and the softening problems of traditional Chinese medicine extract during spray drying, a new method of adding dehumidified air into spray drying process was proposed, and the storage stability conditions of extract powder could be predicted. Kouyanqing extract was taken as model drug to investigate on the wet air (RH = 70%) and dry air conditions of spray drying. Under the dry air condition, the influence of the spray drying result with different air compression ratio and the spray-dried powder properties (extract powder recovery rate, adhesion percentage, water content, angle of repose, compression ratio, particle size and distribution) with 100, 110, 120, 130, 140 °C inlet temperature were studied. The hygroscopic investigation and Tg value with different moisture content of ideal powder were determined. The water activity-equilibrium moisture content (aw-EMC) and the equilibrium moisture content-Tg (EMC-Tg) relationships were fitted by GAB equation and Gordon-Taylor model respectively, and the state diagram of kouyanqing powder was obtained to guide the rational storage conditions. The study found that in the condition of dry air, the extract powder water content decreased with the increase of air compression ratio and the spray drying effect with air compression ratio of 100% was the best performance; in the condition of wet air, the extract powder with high water content and low yield, and the value were 4.26% and 16.73 °C, while, in the dry air condition the values were 2.43% and 24.86 °C with the same other instru- ment parameters. From the analysis of kouyanqing powder state diagram, in order to keep the stability, the critical water content of 3.42% and the critical water content of 0.188. As the water decreased Tg value of extract powder is the major problem of causing adhesion and softening during spray drying, it is meaningful to aid dehumidified air during the process. PMID:26084164

  8. Role of ADS in the back-end of the fuel cycle strategies and associated design activities: The case of Japan

    NASA Astrophysics Data System (ADS)

    Oigawa, Hiroyuki; Tsujimoto, Kazufumi; Nishihara, Kenji; Sugawara, Takanori; Kurata, Yuji; Takei, Hayanori; Saito, Shigeru; Sasa, Toshinobu; Obayashi, Hironari

    2011-08-01

    Reduction of burden caused by radioactive waste management is one of the most critical issues for the sustainable utilization of nuclear power. The Partitioning and Transmutation (P&T) technology provides the possibility to reduce the amount of the radiotoxic inventory of the high-level radioactive waste (HLW) dramatically and to extend the repository capacity. The accelerator-driven system (ADS) is regarded as a powerful tool to effectively transmute minor actinides (MAs) in the "double-strata" fuel cycle strategy. The ADS has a potential to flexibly manage MA in the transient phase from light water reactors (LWRs) to fast breeder reactors (FBRs), and can co-exist with FBR symbiotically and complementarily to enhance the reliability and the safety of the commercial FBR cycle. The concept of ADS in JAEA is a lead-bismuth eutectic (LBE) cooled, tank-type subcritical reactor with the power of 800 MWth driven by a 30 MW superconducting LINAC. By such an ADS, 250 kg of MA can be transmuted annually, which corresponds to the amount of MA produced in 10 units of LWR with 1 GWe. The design study was performed mainly for the subcritical reactor and the spallation target with a beam window. In Japan, Atomic Energy Commission (AEC) has implemented the check and review (C&R) on P&T technology from 2008 to 2009. In the C&R, the benefit of P&T technology, the current status of the R&D, and the way forward to promote it were discussed.

  9. Effect of particle morphology on flow characteristics of a composite plasma spray powder

    NASA Astrophysics Data System (ADS)

    Stanford, Malcolm K.; Eylon, Daniel; Dellacorte, Christopher

    2004-12-01

    The effects of BaF2-CaF2 particle morphology on National Aeronautics and Space Administration (NASA) PS304 feedstock powder flowability were investigated, BaF2-CaF2 eutectic powders were fabricated by comminution (producing an angular morphology) and by gas atomization (producing a spherical morphology). The fluoride powders were added incrementally to the other powder constituents of the NASA PS304 feedstock, (Ni-Cr, Cr2O3, and Ag powders). A linear relationship between flow time and concentration of the BaF2-CaF2 powder was found. The flow of the powder blend with spherical BaF2-CaF2 was better than that with angular BaF2-CaF2. The flowability of the powder blend with angular fluorides decreased linearly with increasing fluoride concentration. However, the flow of the powder blend with spherical fluorides was independent of fluoride concentration. The results suggest that for this material blend, particle morphology plays a significant role in flow behavior, offering potential methods to improve powder flowability and enhance the commercial potential. These findings may be applicable to other difficult-to-flow powders such as cohesive ceramics.

  10. Extending an In Vitro Panel for Estrogenicity Testing: The Added Value of Bioassays for Measuring Antiandrogenic Activities and Effects on Steroidogenesis

    PubMed Central

    Wang, Si; Rijk, Jeroen C.W.; Besselink, Harrie T.; Houtman, René; Peijnenburg,  Ad A.C.M.; Brouwer, Abraham; Rietjens, Ivonne M.C.M.; Bovee,  Toine F.H.

    2014-01-01

    In the present study, a previously established integrated testing strategy (ITS) for in vitro estrogenicity testing was extended with additional in vitro assays in order to broaden its sensitivity to different modes of action resulting in apparent estrogenicity, i.e., other than estrogen receptor (ER) binding. To this end, an extra set of 10 estrogenic compounds with modes of action in part different from ER binding, were tested in the previously defined ITS, consisting of a yeast estrogen reporter gene assay, an U2OS ERα CALUX reporter gene assay and a cell-free coregulator binding assay. Two androgen reporter gene assays and the enhanced H295R steroidogenesis assay were added to that previous defined ITS. These assays had added value, as several estrogenic model compounds also elicited clear and potent antiandrogenic properties and in addition also showed effects on steroidogenesis that might potentiate their apparent estrogenic effects in vivo. Adding these assays, examining mechanisms of action for estrogenicity apart from ERα binding, gives a more complete and comprehensive assessment of the ability of test compounds to interfere with endocrine signaling. It was concluded that the extended ITS will go beyond in vivo estrogenicity testing by the uterotrophic assay, thereby contributing to the 3R-principles. PMID:24928889

  11. Method for producing microcomposite powders using a soap solution

    DOEpatents

    Maginnis, Michael A.; Robinson, David A.

    1996-01-01

    A method for producing microcomposite powders for use in superconducting and non-superconducting applications. A particular method to produce microcomposite powders for use in superconducting applications includes the steps of: (a) preparing a solution including ammonium soap; (b) dissolving a preselected amount of a soluble metallic such as silver nitrate in the solution including ammonium soap to form a first solution; (c) adding a primary phase material such as a single phase YBC superconducting material in particle form to the first solution; (d) preparing a second solution formed from a mixture of a weak acid and an alkyl-mono-ether; (e) adding the second solution to the first solution to form a resultant mixture; (f) allowing the resultant mixture to set until the resultant mixture begins to cloud and thicken into a gel precipitating around individual particles of the primary phase material; (g) thereafter drying the resultant mixture to form a YBC superconducting material/silver nitrate precursor powder; and (h) calcining the YBC superconducting material/silver nitrate precursor powder to convert the silver nitrate to silver and thereby form a YBC/silver microcomposite powder wherein the silver is substantially uniformly dispersed in the matrix of the YBC material.

  12. Parametric Powder Diffraction

    NASA Astrophysics Data System (ADS)

    David, William I. F.; Evans, John S. O.

    The rapidity with which powder diffraction data may be collected, not only at neutron and X-ray synchrotron facilities but also in the laboratory, means that the collection of a single diffraction pattern is now the exception rather than the rule. Many experiments involve the collection of hundreds and perhaps many thousands of datasets where a parameter such as temperature or pressure is varied or where time is the variable and life-cycle, synthesis or decomposition processes are monitored or three-dimensional space is scanned and the three-dimensional internal structure of an object is elucidated. In this paper, the origins of parametric diffraction are discussed and the techniques and challenges of parametric powder diffraction analysis are presented. The first parametric measurements were performed around 50 years ago with the development of a modified Guinier camera but it was the automation afforded by neutron diffraction combined with increases in computer speed and memory that established parametric diffraction on a strong footing initially at the ILL, Grenoble in France. The theoretical parameterisation of quantities such as lattice constants and atomic displacement parameters will be discussed and selected examples of parametric diffraction over the past 20 years will be reviewed that highlight the power of the technique.

  13. Polymer powder prepregging: Scoping study

    NASA Technical Reports Server (NTRS)

    Throne, James L.

    1988-01-01

    Early on, it was found that NEAT LARC-TPI thermoplastic polyimide powder behaved elastoplastically at pressures to 20 ksi and temperatures to 260 degrees celcius (below MP). At high resin assay, resin powder could be continuously cold-flowed around individual carbon fibers in a metal rolling mill. At low resin assay (2:1, C:TPI), fiber breakage was prohibitive. Thus, although processing of TPI below MP would be quite unique, it appears that the polymer must be melted and flowed to produce low resin assay prepreg. Fiber tow was spread to 75 mm using a venturi slot tunnel. This allowed intimate powder/fiber interaction. Two techniques were examined for getting room temperature powder onto the room temperature fiber surface. Electrostatic powder coating allows the charged powder to cling tenaciously to the fiber, even while heated with a hot air gun to above its melt temperature. A variant of the wet slurry coating process was also explored. The carbon fibers are first wetted with water. Then dry powder is sprinkled onto the wet tow and doctor-rolled between the fibers. The wet structure is then taken onto a heated roll, with hot air guns drying and sinter-melting the powder onto the fiber surfaces. In both cases SEM shows individual fibers coated with powder particles that have melted in place and flowed along the fiber surface via surface tension.

  14. [Analysis of Spirulina powder by Fourier transform infrared spectroscopy and calculation of protein content].

    PubMed

    Liu, Hai-Jing; Xu, Chang-Hua; Li, Wei-Ming; Wang, Feng; Zhou, Qun; Li, An; Zhao, Yue-Liang; Ha, Yi-Ming; Sun, Su-Qin

    2013-04-01

    Spirulina, Spirulina powder and dextrin standard were analyzed and identified by Infrared (IR) spectroscopy. The main components, protein (1 657 and 1 537 cm(-1)) and carbohydrate (1 069 and 1054 cm(-1)), had distinct fingerprint characteristics of IR spectra. By comparing the IR spectra of Spirulina, Spirulina powder and dextrin standard, the dominant nutrition in Spirulina powder was identified as protein and carbohydrate. The dominant accessory added in Spirulina powder was dextrin. Comparing the IR spectra of Spirulina powder from 28 different factories and figuring out the correlation provides the information about the amount of accessory. A standard curve of the ratio of absorption peak intensities to protein content was constructed to accurately determine the amount of protein in Spirulina powder.

  15. Prelithiation of silicon-carbon nanotube anodes for lithium ion batteries by stabilized lithium metal powder (SLMP).

    PubMed

    Forney, Michael W; Ganter, Matthew J; Staub, Jason W; Ridgley, Richard D; Landi, Brian J

    2013-09-11

    Stabilized lithium metal powder (SLMP) has been applied during battery assembly to effectively prelithiate high capacity (1500-2500 mAh/g) silicon-carbon nanotube (Si-CNT) anodes, eliminating the 20-40% first cycle irreversible capacity loss. Pressure-activation of SLMP is shown to enhance prelithiation and enable capacity matching between Si-CNT anodes and lithium nickel cobalt aluminum oxide (NCA) cathodes in full batteries with minimal added mass. The prelithiation approach enables high energy density NCA/Si-CNT batteries achieving >1000 cycles at 20% depth-of-discharge.

  16. Strong enhancement of high-field critical current properties and irreversibility field of MgB2 superconducting wires by coronene active carbon source addition via the new B powder carbon-coating method

    NASA Astrophysics Data System (ADS)

    Ye, Shu Jun; Matsumoto, Akiyoshi; Chao Zhang, Yun; Kumakura, Hiroaki

    2014-08-01

    We report an effective carbon-containing additive, coronene (C24H12), for MgB2 superconducting wires. We used B powder coated with C24H12 to fabricate MgB2 wires using the powder-in-tube (PIT) and internal Mg diffusion (IMD) processes. The in-field critical current properties are strongly enhanced for both PIT- and IMD-processed MgB2 wires. For PIT MgB2 wires, a critical current density (Jc) value of 1.8 × 104 A cm-2 is obtained at 4.2 K and 10 T. For IMD MgB2 wires, we obtained a Jc of 1.07 × 105 A cm-2 and an engineering Jc (Je) of 1.12 × 104 A cm-2 at 4.2 K and 10 T. These Jc and Je values are similar to the highest values reported for MgB2 wires thus far. Furthermore, the irreversibility field, Birr, determined with a current density criterion of 100 A cm-2, is strongly enhanced to 25 T at 4.2 K, which is also the highest value reported for MgB2 superconducting wires thus far. Coronene is an active carbon source for MgB2 superconducting wires because (1) coronene has a high carbon content (96 wt%) with a small amount of hydrogen (impurity), (2) the decomposition temperature for coronene is near the reaction temperature between Mg and B, and (3) uniform dispersion of coronene on the B surface can be obtained due to the melting point of coronene being lower than the decomposition temperature. Carbon substitution for B caused by the coronene active carbon source is mainly responsible for the high field critical current properties and the high Birr obtained in this work.

  17. Development of a new method to get a reliable powder flow characteristics using only 1 to 2 g of powder.

    PubMed

    Seppälä, Kari; Heinämäki, Jyrki; Hatara, Juha; Seppälä, Lassi; Yliruusi, Jouko

    2010-03-01

    In powder technology, it is often important to directly measure real powder flow rate from a small amount of powder. For example, in pharmaceutical industry, a frequent problem is to determine powder flow properties of new active pharmaceutical ingredient (API) in an early stage of the development when the amount of API is limited. The purpose of this paper is to introduce a new direct method to measure powder flow when the material is poorly flowing (cohesive) and the amount of material is about 1 to 2 g. The measuring system was simple, consisting of a flow chamber and electronic balance and an automated optical detection system, and for each measurement, only 1 to 2 g of sample was required. Based on the results obtained with this testing method, three selected sugar excipients, three grades of microcrystalline cellulose, and APIs (caffeine, carbamazepine, and paracetamol) can be classified as freely flowing, intermediate flowing, and poorly flowing powders, respectively. The average relative standard deviation for the flow time determinations was not more than 2-10%. The present novel flowability testing method provides a new tool for a rapid determination of flowing characteristics of powders (e.g., inhalation powders) and granules at a small scale.

  18. Investigating the effects of excipients on the powder flow characteristics of theophylline anhydrous powder formulations.

    PubMed

    Nagel, Karen M; Peck, Garnet E

    2003-03-01

    Pharmaceutical excipients may have a great effect on properties affecting tablet production. To determine if formulations containing theophylline anhydrous would have properties allowing them to be easily tableted, functional parameters affecting powder flow were evaluated. The Carr Flowability Indices were used for this evaluation. Formulations to be studied include theophylline anhydrous as the active ingredient, hydrous lactose and dicalcium phosphate dihydrate as diluents, polyvinylpyrrolidone as a binder, and fumed silica as a flow promoter. The effect of each component on powder flow is discussed.

  19. What Value "Value Added"?

    ERIC Educational Resources Information Center

    Richards, Andrew

    2015-01-01

    Two quantitative measures of school performance are currently used, the average points score (APS) at Key Stage 2 and value-added (VA), which measures the rate of academic improvement between Key Stage 1 and 2. These figures are used by parents and the Office for Standards in Education to make judgements and comparisons. However, simple…

  20. Mound powder loader, Mod 1

    SciTech Connect

    Gress, A.V. Jr.

    1985-08-21

    At the investigation of Sandia Albuquerque, a semiautomatic powder loader was designed and fabricated for pyrotechnics devices. The basic functions of the system were to load a precise, measured amount of powder into a charge holder and to compact the mixture to a specified density. This report documents the history, rationale, design, and performance of the Mod 1 loader.

  1. Method of drilling with fluid comprising peanut hulls ground to a powder

    SciTech Connect

    Forrest, G.T.

    1992-02-11

    This patent describes a method of carrying out operations wherein a fluid is circulated in a well extending into the ground. It comprises: taking peanut hulls which have been ground to a powder form, adding the ground peanut hulls to a fluid, and circulating the fluid, with the ground peanut hulls added thereto, in the well.

  2. Antioxidant components and physico-chemical characteristics of jamun powder supplemented pear juice.

    PubMed

    Kapoor, Swati; Ranote, Pushpinder Singh

    2016-05-01

    Studies were conducted to develop jamun powder supplemented pear juice. Two drying methods (Hot air cabinet drying and freeze drying) were used to prepare jamun pulp powder. Jamun powder was then blended with pear juice at 1, 2, 3, 4 and 5 % levels for preparation of jamun powder supplemented pear juice. Among the drying methods used, freeze dried powder retained better bioactive compounds and possessed higher antioxidant activity as compared to hot air dried jamun powder. Analysis of color properties (L*, a*, b*) revealed lower L*, b* values and higher a* values with progression of supplementation levels indicating decreased brightness of product. Pear juice supplemented with 4 % jamun powder received highest overall acceptability scores and was chosen for development of final product. Physico-chemical characteristics of control pear juice did not vary much from when compared to jamun powder supplemented pear juice. Bioactive components mainly total phenols enhanced (9.24 % higher) with addition of jamun powder in pear juice. Addition of anthocyanins from jamun powder to pear juice upon blending improved antioxidant activity of the final product. Supplemented pear juice had 18.13 % higher antioxidant activity than pear juice without supplementation. Storage period of 6 months resulted in significant (p < 0.05) decrease of bioactive compounds and antioxidant activity in jamun powder supplemented pear juice. PMID:27407197

  3. Introducing ADS Labs

    NASA Astrophysics Data System (ADS)

    Accomazzi, Alberto; Henneken, E.; Grant, C. S.; Kurtz, M. J.; Di Milia, G.; Luker, J.; Thompson, D. M.; Bohlen, E.; Murray, S. S.

    2011-05-01

    ADS Labs is a platform that ADS is introducing in order to test and receive feedback from the community on new technologies and prototype services. Currently, ADS Labs features a new interface for abstract searches, faceted filtering of results, visualization of co-authorship networks, article-level recommendations, and a full-text search service. The streamlined abstract search interface provides a simple, one-box search with options for ranking results based on a paper relevancy, freshness, number of citations, and downloads. In addition, it provides advanced rankings based on collaborative filtering techniques. The faceted filtering interface allows users to narrow search results based on a particular property or set of properties ("facets"), allowing users to manage large lists and explore the relationship between them. For any set or sub-set of records, the co-authorship network can be visualized in an interactive way, offering a view of the distribution of contributors and their inter-relationships. This provides an immediate way to detect groups and collaborations involved in a particular research field. For a majority of papers in Astronomy, our new interface will provide a list of related articles of potential interest. The recommendations are based on a number of factors, including text similarity, citations, and co-readership information. The new full-text search interface allows users to find all instances of particular words or phrases in the body of the articles in our full-text archive. This includes all of the scanned literature in ADS as well as a select portion of the current astronomical literature, including ApJ, ApJS, AJ, MNRAS, PASP, A&A, and soon additional content from Springer journals. Fulltext search results include a list of the matching papers as well as a list of "snippets" of text highlighting the context in which the search terms were found. ADS Labs is available at http://adslabs.org

  4. Effects of powder from white cabbage outer leaves on sponge cake quality

    NASA Astrophysics Data System (ADS)

    Prokopov, Tsvetko; Goranova, Zhivka; Baeva, Marianna; Slavov, Anton; Galanakis, Charis M.

    2015-10-01

    The main objective of this study was to develop high fibre cakes utilizing and valorising cabbage by-products - cabbage outer leaves. Cabbage outer leaves were dried and milled in order to produce cabbage leaf powder. The cabbage leaf powder was added at 0, 10, 20% into sponge cake. All of the samples were subjected to physicochemical analysis and sensory evaluation. Methods of descriptive sensory analysis were used for a comparative analysis of the sponge cakes with cabbage leaf powder and the cake without cabbage leaf powder. Addition of cabbage leaf powder in sponge cakes significantly affected the cake volume and textural properties. Springiness of cakes with cabbage leaf powder and crumb tenderness were lower, while the structure was stable at high loads, as expressed by lower shrinkage in comparison with the control cake. The nutritional value of the sponge cakes with cabbage leaf powder was lower than the control cake. The cells cakes modified by cabbage leaf powder were smaller and almost equal, uniformly distributed in the crumb, and at the same time had thicker walls. The cakes with addition of cabbage leaf powder showed the springiness and their crumb tenderness were lower, while their structure was stable at high loads. Control cake showed higher water-absorbing capacity compared to the cakes with 10 and 20% cabbage leaf powder.

  5. Influence of combinations of fenugreek, garlic, and black pepper powder on production traits of the broilers

    PubMed Central

    Kirubakaran, A.; Moorthy, M.; Chitra, R.; Prabakar, G.

    2016-01-01

    Aim: To study the effects of combinations of fenugreek (Trigonella foenum-graecum L.), garlic (Allium sativum), and black pepper (Piper nigrum) powder supplementation on production traits of broiler chickens. Materials and Methods: A total of 288 commercial broiler chicks were randomly assigned to 1-9 groups with 4 replicates each. An experiment was conducted in broilers with different feed formulations; control feed, with no added fenugreek, garlic, and black pepper powder; and 8 treatment groups receiving feed supplemented with different combinations of fenugreek, garlic, and black pepper powder. The individual broilers’ body weight and feed consumption were recorded and calculate the body weight gain and feed conversion ratio (FCR). Results: Broiler’s weight gain and FCR were significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). Cumulative feed consumption was significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). Conclusion: The combination of garlic and black pepper powder supplemented broiler feed fed groups showed higher production performance. The 5 g/kg garlic powder+1 g/kg black pepper powder and 10 g/kg garlic powder+2 g/kg black pepper powder significantly improved the weight gain and FCR. PMID:27284222

  6. Peach skin powder inhibits oxidation in cooked turkey meat.

    PubMed

    Zhang, Y; Han, I; Bridges, W C; Dawson, P L

    2016-10-01

    The objective of this study was to measure the antioxidant activity of peach skin and test the antioxidant effect of peach skin powder on cooked ground turkey meat during 12 d of refrigerated storage. Antioxidant activity of 3 cultivars of peaches grown in South Carolina was first evaluated by 3 antioxidant assays. The peach variety O'Henry showed the greatest antioxidant effect and therefore was used for further study. Two levels of peach skin powder (0.5%, 1%) and 0.01% butylated hydroxylanisole (BHA) were applied to ground turkey meat. Oxidation of cooked turkey meat was measured by detection of hexanal using gas chromatography-mass spectrometry. Results indicated that all levels of peach skin powder used in this study had an antioxidant effect on ground turkey with a greater effect at the higher concentration. O'Henry peach skin powder was as effective as BHA in preventing oxidation at the levels tested. PMID:27252372

  7. Influence of bamboo shoot powder fortification on physico-chemical, textural and organoleptic characteristics of biscuits.

    PubMed

    Choudhury, Monisha; Badwaik, Laxmikant S; Borah, Pallab Kumar; Sit, Nandan; Deka, Sankar C

    2015-10-01

    Bamboo shoot has attracted significant research and a commercial interest due to its many health-promoting bioactive compounds as well as its effectiveness in decreasing blood pressure, cholesterol and increasing appetite. As availability of fresh shoot is limited due to its seasonality there is need of incorporation of nutrients of shoot to any common food product which is easily available throughout year. Shoots of Bambusa balcooa variety were taken and edible parts were separated. Slices of shoot were boiled, dried, powdered, sieved, analysed for nutritional status and used for biscuit making. Bamboo shoot powder (BSP) was added in 0 % (control), 5, 10, and 15 % level in dry ingredients by replacing wheat flour and other ingredients were kept constant. Dough prepared are firstly analysed for basic characteristics. Then biscuits were prepared and analyzed for moisture, water activity, protein, fiber, fat, ash, phenolics, antioxidant activity, dimension, hardness, color and sensory acceptability. Variations were observed for fiber, antioxidant activity and phenolics from 1.08 to 1.97 %, 3.50 to 17.85 % and 0.45 to 4.19 mg/100 g respectively. Results showed that up to 10 % fortification level the biscuits were acceptable with improved functional and neutraceutical properties compared to the control.

  8. Influence of bamboo shoot powder fortification on physico-chemical, textural and organoleptic characteristics of biscuits.

    PubMed

    Choudhury, Monisha; Badwaik, Laxmikant S; Borah, Pallab Kumar; Sit, Nandan; Deka, Sankar C

    2015-10-01

    Bamboo shoot has attracted significant research and a commercial interest due to its many health-promoting bioactive compounds as well as its effectiveness in decreasing blood pressure, cholesterol and increasing appetite. As availability of fresh shoot is limited due to its seasonality there is need of incorporation of nutrients of shoot to any common food product which is easily available throughout year. Shoots of Bambusa balcooa variety were taken and edible parts were separated. Slices of shoot were boiled, dried, powdered, sieved, analysed for nutritional status and used for biscuit making. Bamboo shoot powder (BSP) was added in 0 % (control), 5, 10, and 15 % level in dry ingredients by replacing wheat flour and other ingredients were kept constant. Dough prepared are firstly analysed for basic characteristics. Then biscuits were prepared and analyzed for moisture, water activity, protein, fiber, fat, ash, phenolics, antioxidant activity, dimension, hardness, color and sensory acceptability. Variations were observed for fiber, antioxidant activity and phenolics from 1.08 to 1.97 %, 3.50 to 17.85 % and 0.45 to 4.19 mg/100 g respectively. Results showed that up to 10 % fortification level the biscuits were acceptable with improved functional and neutraceutical properties compared to the control. PMID:26396424

  9. Preparation of superconductor precursor powders

    DOEpatents

    Bhattacharya, R.

    1998-08-04

    A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic and/or reduced particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of all metals in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products. 7 figs.

  10. Preparation of superconductor precursor powders

    DOEpatents

    Bhattacharya, Raghunath; Blaugher, Richard D.

    1995-01-01

    A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals, such as nitrate salts of thallium, barium, calcium, and copper, which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of thallium in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products.

  11. Preparation of Ultrafine W-Cu Composite Powder Using Ultrasonic-Assisted Electroless Plating

    NASA Astrophysics Data System (ADS)

    Huang, Limei; Luo, Laima; Ding, Xiaoyu; Zan, Xiang; Hong, Yu; Cheng, Jigui; Wu, Yucheng; Luo, Guangnan; Zhu, Liu

    2013-07-01

    W-Cu ultrafine/nanocomposite powders have high sintering activity, so ultrafine/nanotechnology of W-Cu composite powders is one of the main methods to obtain fully dense, high-performance W-Cu composite materials. Cu-coated ultrafine W composite powders were synthesized by ultrasonic-assisted electroless plating process with non-noble metal activation pretreatment at room temperature in this paper. The growth mechanism of Cu layers and surface morphologies and composition of initial ultrafine W powders, pretreated W powders and Cu-coated W powders were analyzed by field emission scanning electron microscopy (FE-SEM), and energy dispersion spectrometry (EDS). The results show that the uniformly Cu coated W composite powder is successfully synthesized without conventional sensitization and activation steps by ultrasonic-assisted electroless plating at room temperature. The Cu layers on the ultrafine W powders had cell structure with dense, uniform distribution. The growth mechanism of Cu layers appears as follows: the surfaces of pretreated W powders appear linear-like and lamellar-like surface defects which act as activated sites. The reactants in the plating solution were adsorbed on catalytic activity surfaces of powders and happened oxidation-reduction reaction. The growth and aggregation mechanisms of Cu particles after nucleation are stripy Cu-cells grew up, bend, bifurcated, and aggregated, then wounding into a cellular structure, like "wrapping wool clusters" in the life. Finally, Cu cells grow up and merge into a layer.

  12. Silica powders for powder evacuated thermal insulating panel and method

    DOEpatents

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1996-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  13. Silica powders for powder evacuated thermal insulating panel and method

    DOEpatents

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1994-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2 /g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  14. Silica powders for powder evacuated thermal insulating panel and method

    DOEpatents

    Harris, M.T.; Basaran, O.A.; Kollie, T.G.; Weaver, F.J.

    1996-01-02

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm{sup 3} and an external surface area in the range of about 90 to 600 m{sup 2}/g is described. The silica powders are prepared by reacting a tetraalkyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders. 2 figs.

  15. Silica powders for powder evacuated thermal insulating panel and method

    DOEpatents

    Harris, Michael T.; Basaran, Osman A.; Kollie, Thomas G.; Weaver, Fred J.

    1995-01-01

    A powder evacuated thermal insulating panel using generally spherical and porous silica particles of a median size less than about 100 nanometers in diameter, a pour packing density of about 0.4 to 0.6 g/cm.sup.3 and an external surface area in the range of about 90 to 600 m.sup.2/ g is described. The silica powders are prepared by reacting a tetraakyl silicate with ammonia and water in an alcohol solvent, distilling the solution after the reaction to remove the ammonia and recover the alcohol. The resulting aqueous slurry was dried, ball-milled, and dried again to provide the silica particles with defined internal and external porosity. The nanometer size and the large external surface area of the silica particles along with the internal and external porosity of the silica particles provide powder evacuated thermal insulating panels with significantly higher R-values than obtainable using previously known silica powders.

  16. powder in water

    NASA Astrophysics Data System (ADS)

    Chan, Ya-Ting; Wu, Chao-Hsien; Shen, Pouyan; Chen, Shuei-Yuan

    2014-09-01

    Submicron-sized NiAl2+ X O4 fragments and nanocondensates of Ni-doped γ-Al2O3, Al-doped NiO and β-Ni(OH)2 were synthesized simultaneously by pulsed laser ablation of NiAl2O4 powder in water and characterized using X-ray/electron diffraction and optical spectroscopy. The NiAl2+ X O4 is Al-enriched spinel with dislocations and subgrains. The Ni-doped γ-Al2O3 spinel has paracrystalline distribution (i.e., with fair constant longitudinal spacing, but variable relative lateral translations) of defect clusters and intimate intergrowth of θ-Al2O3 and 2x(3) commensurate superstructure. The Al-doped NiO has perfect cubo-octahedron shape and as small as 5 nm in size. The β-Ni(OH)2 and 1-D turbostratic hydroxide lamellae occurred as a matrix of these oxide nanoparticles. The colloidal suspension containing the composite phases has a minimum band gap of 5.3 eV for potential photocatalytic applications.

  17. Exercise and food ad libitum reduce the impact of early in life nutritional inbalances on nitrergic activity of hippocampus and striatum.

    PubMed

    Viana, Lane Coelho; Torres, João Bento; Farias, José Augusto; Kawhage, Rafael; Lins, Nara; Passos, Aline; Quintairos, Amanda; Trévia, Nonata; Guedes, Rubem Carlos Araújo; Diniz, Cristovam Wanderley Picanço

    2007-01-01

    Nutritional imbalances were produced by varying litter size pups per dam: 3 (small), 6 (medium), and 12 (large). On the 21st day, 4 subjects of each litter, were sacrificed and the remaining were grouped, 2 per cage, with or without running wheels, with food and water ad libitum. Adult subjects were tested in water maze, their brains processed for NADPH-diaphorase histochemistry and quantified by densitometry. No differences were detected in water maze. At 21st day, S and L compared with M presented reduced NADPH-d in the stratum molecular of dentate gyrus (DG), stratum lacunosum of CA1 and in all CA3 layers but not in the striatum. On the 58th day, actvity remained low in S and L in CA3 and striatum and L in CA1 and DG. Voluntary exercise increased NADPH-d in DG, CA1, CA3, and striatum in S, and in the stratum lacunosum of CA1 and CA3 in L.

  18. Two Virasoro symmetries in stringy warped AdS3

    NASA Astrophysics Data System (ADS)

    Compère, Geoffrey; Guica, Monica; Rodriguez, Maria J.

    2014-12-01

    We study three-dimensional consistent truncations of type IIB supergravity which admit warped AdS3 solutions. These theories contain subsectors that have no bulk dynamics. We show that the symplectic form for these theories, when restricted to the non-dynamical subsectors, equals the symplectic form for pure Einstein gravity in AdS3. Consequently, for each consistent choice of boundary conditions in AdS3, we can define a consistent phase space in warped AdS3 with identical conserved charges. This way, we easily obtain a Virasoro × Virasoro asymptotic symmetry algebra in warped AdS3; two different types of Virasoro × Kač-Moody symmetries are also consistent alternatives.

  19. Method for molding ceramic powders

    DOEpatents

    Janney, M.A.

    1990-01-16

    A method for molding ceramic powders comprises forming a slurry mixture including ceramic powder, a dispersant for the metal-containing powder, and a monomer solution. The monomer solution includes at least one multifunctional monomer, a free-radical initiator, and an organic solvent. The slurry mixture is transferred to a mold, and the mold containing the slurry mixture is heated to polymerize and crosslink the monomer and form a firm polymer-solvent gel matrix. The solid product may be removed from the mold and heated to first remove the solvent and subsequently remove the polymer, where after the product may be sintered.

  20. Method for molding ceramic powders

    DOEpatents

    Janney, Mark A.

    1990-01-01

    A method for molding ceramic powders comprises forming a slurry mixture including ceramic powder, a dispersant for the metal-containing powder, and a monomer solution. The monomer solution includes at least one multifunctional monomer, a free-radical initiator, and an organic solvent. The slurry mixture is transferred to a mold, and the mold containing the slurry mixture is heated to polymerize and crosslink the monomer and form a firm polymer-solvent gel matrix. The solid product may be removed from the mold and heated to first remove the solvent and subsequently remove the polymer, whereafter the product may be sintered.