Science.gov

Sample records for addition significantly higher

  1. Competitive Intelligence: Significance in Higher Education

    ERIC Educational Resources Information Center

    Barrett, Susan E.

    2010-01-01

    Historically noncompetitive, the higher education sector is now having to adjust dramatically to new and increasing demands on numerous levels. To remain successfully operational within the higher educational market universities today must consider all relevant forces which can impact present and future planning. Those institutions that were…

  2. Addition of Cryoprotectant Significantly Alters the Epididymal Sperm Proteome.

    PubMed

    Yoon, Sung-Jae; Rahman, Md Saidur; Kwon, Woo-Sung; Park, Yoo-Jin; Pang, Myung-Geol

    2016-01-01

    Although cryopreservation has been developed and optimized over the past decades, it causes various stresses, including cold shock, osmotic stress, and ice crystal formation, thereby reducing fertility. During cryopreservation, addition of cryoprotective agent (CPA) is crucial for protecting spermatozoa from freezing damage. However, the intrinsic toxicity and osmotic stress induced by CPA cause damage to spermatozoa. To identify the effects of CPA addition during cryopreservation, we assessed the motility (%), motion kinematics, capacitation status, and viability of epididymal spermatozoa using computer-assisted sperm analysis and Hoechst 33258/chlortetracycline fluorescence staining. Moreover, the effects of CPA addition were also demonstrated at the proteome level using two-dimensional electrophoresis. Our results demonstrated that CPA addition significantly reduced sperm motility (%), curvilinear velocity, viability (%), and non-capacitated spermatozoa, whereas straightness and acrosome-reacted spermatozoa increased significantly (p < 0.05). Ten proteins were differentially expressed (two decreased and eight increased) (>3 fold, p < 0.05) after CPA, whereas NADH dehydrogenase flavoprotein 2, f-actin-capping protein subunit beta, superoxide dismutase 2, and outer dense fiber protein 2 were associated with several important signaling pathways (p < 0.05). The present study provides a mechanistic basis for specific cryostresses and potential markers of CPA-induced stress. Therefore, these might provide information about the development of safe biomaterials for cryopreservation and basic ground for sperm cryopreservation. PMID:27031703

  3. Addition of Cryoprotectant Significantly Alters the Epididymal Sperm Proteome

    PubMed Central

    Yoon, Sung-Jae; Rahman, Md Saidur; Kwon, Woo-Sung; Park, Yoo-Jin; Pang, Myung-Geol

    2016-01-01

    Although cryopreservation has been developed and optimized over the past decades, it causes various stresses, including cold shock, osmotic stress, and ice crystal formation, thereby reducing fertility. During cryopreservation, addition of cryoprotective agent (CPA) is crucial for protecting spermatozoa from freezing damage. However, the intrinsic toxicity and osmotic stress induced by CPA cause damage to spermatozoa. To identify the effects of CPA addition during cryopreservation, we assessed the motility (%), motion kinematics, capacitation status, and viability of epididymal spermatozoa using computer-assisted sperm analysis and Hoechst 33258/chlortetracycline fluorescence staining. Moreover, the effects of CPA addition were also demonstrated at the proteome level using two-dimensional electrophoresis. Our results demonstrated that CPA addition significantly reduced sperm motility (%), curvilinear velocity, viability (%), and non-capacitated spermatozoa, whereas straightness and acrosome-reacted spermatozoa increased significantly (p < 0.05). Ten proteins were differentially expressed (two decreased and eight increased) (>3 fold, p < 0.05) after CPA, whereas NADH dehydrogenase flavoprotein 2, f-actin-capping protein subunit beta, superoxide dismutase 2, and outer dense fiber protein 2 were associated with several important signaling pathways (p < 0.05). The present study provides a mechanistic basis for specific cryostresses and potential markers of CPA-induced stress. Therefore, these might provide information about the development of safe biomaterials for cryopreservation and basic ground for sperm cryopreservation. PMID:27031703

  4. Mentoring into Higher Education: A Useful Addition to the Landscape of Widening Access to Higher Education?

    ERIC Educational Resources Information Center

    Wilson, Alistair; Hunter, Katie; Spohrer, Konstanze; Bruner, Richard; Beasley, Anna

    2014-01-01

    Alan Milburn, the Chair of the Government's Social Mobility and Child Poverty Commission recently highlighted the role of education in progressing social mobility in Scotland; "In my view it's a grave social injustice that only one in forty pupils from Scotland's most deprived households…got three As in their Highers in 2011, compared to one…

  5. The Significance of Australian Vocational Education Institutions in Opening Access to Higher Education

    ERIC Educational Resources Information Center

    Moodie, Gavin; Wheelahan, Leesa

    2009-01-01

    Vocational education provides an educational but not a social ladder of opportunity to Australian higher education. The five dual-sector universities with significant enrolments in both vocational and higher education admit about twice the proportion of students transferring from vocational education as other universities. However, since the…

  6. Higher resolution stimulus facilitates depth perception: MT+ plays a significant role in monocular depth perception.

    PubMed

    Tsushima, Yoshiaki; Komine, Kazuteru; Sawahata, Yasuhito; Hiruma, Nobuyuki

    2014-01-01

    Today, we human beings are facing with high-quality virtual world of a completely new nature. For example, we have a digital display consisting of a high enough resolution that we cannot distinguish from the real world. However, little is known how such high-quality representation contributes to the sense of realness, especially to depth perception. What is the neural mechanism of processing such fine but virtual representation? Here, we psychophysically and physiologically examined the relationship between stimulus resolution and depth perception, with using luminance-contrast (shading) as a monocular depth cue. As a result, we found that a higher resolution stimulus facilitates depth perception even when the stimulus resolution difference is undetectable. This finding is against the traditional cognitive hierarchy of visual information processing that visual input is processed continuously in a bottom-up cascade of cortical regions that analyze increasingly complex information such as depth information. In addition, functional magnetic resonance imaging (fMRI) results reveal that the human middle temporal (MT+) plays a significant role in monocular depth perception. These results might provide us with not only the new insight of our neural mechanism of depth perception but also the future progress of our neural system accompanied by state-of- the-art technologies. PMID:25327168

  7. Higher resolution stimulus facilitates depth perception: MT+ plays a significant role in monocular depth perception.

    PubMed

    Tsushima, Yoshiaki; Komine, Kazuteru; Sawahata, Yasuhito; Hiruma, Nobuyuki

    2014-10-20

    Today, we human beings are facing with high-quality virtual world of a completely new nature. For example, we have a digital display consisting of a high enough resolution that we cannot distinguish from the real world. However, little is known how such high-quality representation contributes to the sense of realness, especially to depth perception. What is the neural mechanism of processing such fine but virtual representation? Here, we psychophysically and physiologically examined the relationship between stimulus resolution and depth perception, with using luminance-contrast (shading) as a monocular depth cue. As a result, we found that a higher resolution stimulus facilitates depth perception even when the stimulus resolution difference is undetectable. This finding is against the traditional cognitive hierarchy of visual information processing that visual input is processed continuously in a bottom-up cascade of cortical regions that analyze increasingly complex information such as depth information. In addition, functional magnetic resonance imaging (fMRI) results reveal that the human middle temporal (MT+) plays a significant role in monocular depth perception. These results might provide us with not only the new insight of our neural mechanism of depth perception but also the future progress of our neural system accompanied by state-of- the-art technologies.

  8. Addition of higher order plate and shell elements into NASTRAN computer program

    NASA Technical Reports Server (NTRS)

    Narayanaswami, R.; Goglia, G. L.

    1976-01-01

    Two higher order plate elements, the linear strain triangular membrane element and the quintic bending element, along with a shallow shell element, suitable for inclusion into the NASTRAN (NASA Structural Analysis) program are described. Additions to the NASTRAN Theoretical Manual, Users' Manual, Programmers' Manual and the NASTRAN Demonstration Problem Manual, for inclusion of these elements into the NASTRAN program are also presented.

  9. The Inception of the Meaning and Significance of Endowment in American Higher Education, 1890-1930

    ERIC Educational Resources Information Center

    Kimball, Bruce A.; Johnson, Benjamin Ashby

    2012-01-01

    Background/Context: Endowments of institutions of higher education in the United States have attracted widespread attention in recent decades due to their meteoric rise in value and their precipitous decline during the recent recession. But there has been little research on the beginnings of the significant interest in and importance of…

  10. Addition of Zn to the ternary Mg-Ca-Sr alloys significantly improves their antibacterial property

    PubMed Central

    He, Guanping; Wu, Yuanhao; Zhang, Yu; Zhu, Ye; Liu, Yang; Li, Nan; Li, Mei; Zheng, Guan; He, Baohua; Yin, Qingshui; Zheng, Yufeng; Mao, Chuanbin

    2015-01-01

    Most of the magnesium (Mg) alloys possess excellent biocompatibility, mechanical property and biodegradability in orthopedic applications. However, these alloys may suffer from bacterial infections due to their insufficient antibacterial capability. In order to reduce the post-surgical infections, a series of biocompatible Mg–1Ca-0.5Sr-xZn (x=0, 2, 4, 6) alloys were fabricated with the addition of antibacterial Zn with variable content and evaluated in terms of their biocompatibility and antibacterial property. The in vitro corrosion study showed that Mg-1Ca-0.5Sr-6Zn alloys exhibited a higher hydrogen evolution volume after 100 h immersion and resulted in a higher pH value of the immersion solution. Our work indicated that Zn-containing Mg alloys exhibited good biocompatibility with high cell viability. The antibacterial studies reveal that the number of bacteria adhered on all of these Mg alloy samples diminished remarkably compared to the Ti-6Al-4V control group. We also found that the proliferation of the bacteria was inhibited by these Mg alloys extracts. Among the prepared alloys, Mg-1Ca-0.5Sr-6Zn alloy not only exhibited a strong antibacterial effect, but also promoted the proliferation of MC3T3-E1 osteoblasts, suggesting that it is a promising alloy with both good antibacterial property and good biocompatibility for use as an orthopedic implant. PMID:26693010

  11. Significant enhancement of the superconducting properties of MgB2 by polyvinyl alcohol additives

    NASA Astrophysics Data System (ADS)

    Zeng, R.; Lu, L.; Dou, S. X.

    2008-08-01

    We report a systematic study of the effects of polymer addition on the lattice parameters, microstructure and superconducting properties of MgB2. Polyvinyl alcohol [-C2H4O-]n (PVA) as a typical polymer was used as an additive to MgB2. It was found that PVA additions have the following features: (1) the polymer can have a very low oxygen (O) content or even none at all, and PVA has a low O content (C:O = 2:1), which reduces the impurities brought into MgB2 from the doping, and (2) PVA decomposes at a temperature of 400-650 °C, which means that the reaction occurs in the same temperature range as MgB2 formation, providing highly reactive C, which homogeneously substitutes for B at this low-temperature range. The above considerations significantly enhance the critical current, Jc, the irreversibility field, Hirr, and the upper critical field, Hc2, of MgB2 compared to un-doped samples or those doped with other carbon sources. In this work, suitable PVA doping levels improved both the connectivity and flux pinning, so that the Jc of PVA-doped MgB2 was improved over the whole field range.

  12. PCOS women show significantly higher homocysteine level, independent to glucose and E2 level

    PubMed Central

    Eskandari, Zahra; Sadrkhanlou, Rajab-Ali; Nejati, Vahid; Tizro, Gholamreza

    2016-01-01

    Background: It is reasonable to think that some biochemical characteristics of follicular fluid (FF) surrounding the oocyte may play a critical role in determining the quality of oocyte and the subsequent potential needed to achieve fertilization and embryo development. Objective: This study was carried out to evaluate the levels of FF homocysteine (Hcy) in IVF candidate polycystic ovary syndrome (PCOS) women and any relationships with FF glucose and estradiol (E2) levels. Materials and Methods: In this case control study which was performed in Dr. Tizro Day Care and IVF Center 70 infertile patients were enrolled in two groups: comprising 35 PCOS and 35 non PCOS women. Long protocol was performed for all patients. FF Hcy, glucose and E2 levels were analyzed at the time of oocyte retrieval. Results: It was observed that FF Hcy level was significantly higher in PCOS patients compared with non PCOSs (p<0.01). Observations demonstrated that in PCOS group, the Hcy level increased independent to E2, glucose levels, BMI and age, while the PCOS group showed significantly higher BMI compared with non-PCOS group (p=0.03). However, no significant differences were revealed between groups for FF glucose and E2 levels. Conclusion: Present data showed that although FF glucose and E2 levels were constant in PCOS and non PCOS patients, but the FF Hcy levels in PCOS were significantly increased (p=0.01). PMID:27679823

  13. PCOS women show significantly higher homocysteine level, independent to glucose and E2 level

    PubMed Central

    Eskandari, Zahra; Sadrkhanlou, Rajab-Ali; Nejati, Vahid; Tizro, Gholamreza

    2016-01-01

    Background: It is reasonable to think that some biochemical characteristics of follicular fluid (FF) surrounding the oocyte may play a critical role in determining the quality of oocyte and the subsequent potential needed to achieve fertilization and embryo development. Objective: This study was carried out to evaluate the levels of FF homocysteine (Hcy) in IVF candidate polycystic ovary syndrome (PCOS) women and any relationships with FF glucose and estradiol (E2) levels. Materials and Methods: In this case control study which was performed in Dr. Tizro Day Care and IVF Center 70 infertile patients were enrolled in two groups: comprising 35 PCOS and 35 non PCOS women. Long protocol was performed for all patients. FF Hcy, glucose and E2 levels were analyzed at the time of oocyte retrieval. Results: It was observed that FF Hcy level was significantly higher in PCOS patients compared with non PCOSs (p<0.01). Observations demonstrated that in PCOS group, the Hcy level increased independent to E2, glucose levels, BMI and age, while the PCOS group showed significantly higher BMI compared with non-PCOS group (p=0.03). However, no significant differences were revealed between groups for FF glucose and E2 levels. Conclusion: Present data showed that although FF glucose and E2 levels were constant in PCOS and non PCOS patients, but the FF Hcy levels in PCOS were significantly increased (p=0.01).

  14. Significantly improved cyclability of lithium manganese oxide under elevated temperature by an easily oxidized electrolyte additive

    NASA Astrophysics Data System (ADS)

    Zhu, Yunmin; Rong, Haibo; Mai, Shaowei; Luo, Xueyi; Li, Xiaoping; Li, Weishan

    2015-12-01

    Spinel lithium manganese oxide, LiMn2O4, is a promising cathode for lithium ion battery in large-scale applications, because it possesses many advantages compared with currently used layered lithium cobalt oxide (LiCoO2) and olivine phosphate (LiFePO4), including naturally abundant resource, environmental friendliness and high and long work potential plateau. Its poor cyclability under high temperature, however, limits its application. In this work, we report a significant cyclability improvement of LiMn2O4 under elevated temperature by using dimethyl phenylphonite (DMPP) as an electrolyte additive. Charge/discharge tests demonstrate that the application of 0.5 wt.% DMPP yields a capacity retention improvement from 16% to 82% for LiMn2O4 after 200 cycles under 55 °C at 1 C (1C = 148 mAh g-1) between 3 and 4.5 V. Electrochemical and physical characterizations indicate that DMPP is electrochemically oxidized at the potential lower than that for lithium extraction, forming a protective cathode interphase on LiMn2O4, which suppresses the electrolyte decomposition and prevents LiMn2O4 from crystal destruction.

  15. Risk of abnormal triple screen for Down syndrome is significantly higher in patients with female fetuses.

    PubMed

    Spong, C Y; Ghidini, A; Stanley-Christian, H; Meck, J M; Seydel, F D; Pezzullo, J C

    1999-04-01

    Previous studies have shown that mid-trimester maternal serum alpha-fetoprotein (AFP) levels are significantly higher and human chorionic gonadotrophin (hCG) levels significantly lower in women with male compared with female fetuses. We have evaluated whether triple-screen criteria are more likely to identify women with female fetuses as at risk for Down syndrome. From the Georgetown University genetics database we obtained the absolute values and corresponding multiples of the median (MoM) for AFP, hCG and unconjugated oestriol (uE3) in singleton gestations for the period database November 1992 July 1996. A Down syndrome risk of 1/270 or greater at mid-trimester was considered as high risk. A total of 977 patients with triple screen and outcome information were identified, including 502 female and 475 male fetuses. Patients with female fetuses were significantly more likely to have lower serum AFP (p=0.003) and a positive triple screen for Down syndrome (72 (14 per cent) versus 45 (9 per cent), p<0.02) than those with male fetuses. The gestational age at triple screen, maternal serum hCG and uE3, race and diabetes were not significantly different between the two groups. Since Down syndrome is less common in female than male fetuses, and the rates of female and male Down syndrome fetuses detected by triple screen and subsequent amniocentesis are not significantly different, the excess of positive mid-trimester maternal serum triple screen in women with female fetuses is likely due to false-positive results. PMID:10327139

  16. Docosahexaenoic acid content is significantly higher in ghrita prepared by traditional Ayurvedic method

    PubMed Central

    Joshi, Kalpana S.

    2014-01-01

    Background: Ghee (clarified butter) also known as ghrita, has been utilized for thousands of years in Ayurveda. Ghee is mostly prepared by traditional method in Indian households or by direct cream method at industry level. Ayurvedic classics mention that ghrita made from cow milk is superior. However, there is no scientific comparison available on preparation methods and essential fatty acids content of ghrita. Objective: To investigate fatty acid composition of ghrita prepared by traditional/Ayurvedic method and commercial method (direct cream method). Materials and Methods: Fatty Acid Methyl Esters (FAME) extracted from ghrita samples were analysed on Gas Chromatography (GC) Shimadzu B using capillary column BPX70 (0.32 mm*60 m, ID of 0.25 mm). The fatty acids in the samples were identified by comparing peaks with the external standard 68A (Nu-Chek-Prep, Inc.USA). Significant differences between the experimental groups were assessed by analysis of variance. Results: Distribution of fatty acids was compared in ghrita samples prepared by traditional method and direct cream method which is commercially used. Saturated fatty acids were predominant in both the groups. Mono unsaturated fatty acids and poly unsaturated fatty acids were in the range of 17-18% and 3-6% respectively. DHA content was significantly higher in ghee prepared by traditional method using curd starter fermentation. Conclusion: The findings suggested that ghrita prepared by traditional ayurvedic methods contains higher amount of DHA; Omega-3 long-chain polyunsaturated fatty acids, which is a major component of retinal and brain tissues and remains important in prevention of various diseases. PMID:24948858

  17. Additives

    NASA Technical Reports Server (NTRS)

    Smalheer, C. V.

    1973-01-01

    The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

  18. Significantly Higher Prevalence Rate of Asthma and Bipolar Disorder Co-Morbidity

    PubMed Central

    Wu, Ming-Kung; Wang, Hung-Yu; Chen, Yen-Wen; Lin, Pao-Yen; Wu, Ching-Kuan; Tseng, Ping-Tao

    2016-01-01

    Abstract Asthma and bipolar disorder (BD) are 2 distinct diseases that share similar pathophysiology. This study aimed to determine their relationship thorough a meta-analysis of articles on their comorbidity rate. The aim of the study is to examine the overall prevalence rate of BD in asthmatic patients and of asthma in BD patients compared to healthy controls. Electronic research of PubMed and ClinicalTrials.gov was performed. Articles discussing the prevalence rate of BD in patients with/without asthma and the prevalence rate of asthma in those with/without BD, as well as clinical trials in humans and case-controlled trials or cohort studies, were all included. Case reports or series and nonclinical trials were excluded. Through a random-effects model, a meta-analysis of the results of 4 studies comparing the prevalence rate of BD in patients with/without asthma, and in 6 studies comparing the prevalence rate of asthma in subjects with/without BD were performed. There were significantly higher prevalence rates of BD in asthmatic patients than in healthy controls (P < 0.001) and of asthma in BD patients than in healthy controls (P < 0.001). Only the patient's mean age significantly modulated the odds ratio of the prevalence rate of asthma in BD patients (slope = 0.015, P < 0.001). Only 10 studies were included and most were cross-sectional studies. The possible confounding effect of medication on BD or asthma onset was not investigated. Any possible etiology of the comorbidity was also not determined. This meta-analysis highlights the importance of the significantly high comorbid rate of BD and asthma, and the positive association with age. Special attention must be given to the comorbidity of asthma and BD, especially in older patients. PMID:27043688

  19. Significantly Improving Regional Seismic Amplitude Tomography at Higher Frequencies by Determining S -Wave Bandwidth

    DOE PAGES

    Fisk, Mark D.; Pasyanos, Michael E.

    2016-05-03

    Characterizing regional seismic signals continues to be a difficult problem due to their variability. Calibration of these signals is very important to many aspects of monitoring underground nuclear explosions, including detecting seismic signals, discriminating explosions from earthquakes, and reliably estimating magnitude and yield. Amplitude tomography, which simultaneously inverts for source, propagation, and site effects, is a leading method of calibrating these signals. A major issue in amplitude tomography is the data quality of the input amplitude measurements. Pre-event and prephase signal-to-noise ratio (SNR) tests are typically used but can frequently include bad signals and exclude good signals. The deficiencies ofmore » SNR criteria, which are demonstrated here, lead to large calibration errors. To ameliorate these issues, we introduce a semi-automated approach to assess the bandwidth of a spectrum where it behaves physically. We determine the maximum frequency (denoted as Fmax) where it deviates from this behavior due to inflections at which noise or spurious signals start to bias the spectra away from the expected decay. We compare two amplitude tomography runs using the SNR and new Fmax criteria and show significant improvements to the stability and accuracy of the tomography output for frequency bands higher than 2 Hz by using our assessments of valid S-wave bandwidth. We compare Q estimates, P/S residuals, and some detailed results to explain the improvements. Lastly, for frequency bands higher than 4 Hz, needed for effective P/S discrimination of explosions from earthquakes, the new bandwidth criteria sufficiently fix the instabilities and errors so that the residuals and calibration terms are useful for application.« less

  20. Magnitude and significance of the higher-order reduced density matrix cumulants

    NASA Astrophysics Data System (ADS)

    Herbert, John M.

    Using full configuration interaction wave functions for Be and LiH, in both minimal and extended basis sets, we examine the absolute magnitude and energetic significance of various contributions to the three-electron reduced density matrix (3-RDM) and its connected (size-consistent) component, the 3-RDM cumulant (3-RDMC). Minimal basis sets are shown to suppress the magnitude of the 3-RDMC in an artificial manner, whereas in extended basis sets, 3-RDMC matrix elements are often comparable in magnitude to the corresponding 3-RDM elements, even in cases where this result is not required by spin angular momentum coupling. Formal considerations suggest that these observations should generalize to higher-order p-RDMs and p-RDMCs (p > 3). This result is discussed within the context of electronic structure methods based on the contracted Schrödinger equation (CSE), as solution of the CSE relies on 3- and 4-RDM ?reconstruction functionals? that neglect the 3-RDMC, the 4-RDMC, or both. Although the 3-RDMC is responsible for at most 0.2% of the total electronic energy in Be and LiH, it accounts for up to 70% of the correlation energy, raising questions regarding whether (and how) the CSE can offer a useful computational methodology.

  1. Higher Education Financing in the Fifty States: Significance for the 'Adams' States.

    ERIC Educational Resources Information Center

    Budig, Jeanne E.; Khan, Anwar

    Findings of a study on higher education financing in the states are summarized with specific reference for the states covered by the 1977 Adams versus Richardson decision. The study, "Higher Education Financing in the Fifty States: Interstate Comparisons" (Marilyn McCoy, D. Kent Halstead), was jointly issued by the National Center for Higher…

  2. Injection route and TLR9 agonist addition significantly impact heroin vaccine efficacy.

    PubMed

    Bremer, Paul T; Schlosburg, Joel E; Lively, Jenny M; Janda, Kim D

    2014-03-01

    Active immunization is an effective means of blocking the pharmacodynamic effects of drugs and holds promise as a treatment for heroin addiction. Previously, we demonstrated the efficacy of our first-generation vaccine in blocking heroin self-administration in rats, however, many vaccine components can be modified to further improve performance. Herein we examine the effects of varying heroin vaccine injection route and adjuvant formulation. Mice immunized via subcutaneous (sc) injection exhibited inferior anti-heroin titers compared to intraperitoneal (ip) and sc/ip coadministration injection routes. Addition of TLR9 agonist cytosine-guanine oligodeoxynucleotide 1826 (CpG ODN 1826) to the original alum adjuvant elicited superior antibody titers and opioid affinities compared to alum alone. To thoroughly assess vaccine efficacy, full dose-response curves were generated for heroin-induced analgesia in both hot plate and tail immersion tests. Mice treated with CpG ODN 1826 exhibited greatly shifted dose-response curves (10-13-fold vs unvaccinated controls) while non-CpG ODN vaccine groups did not exhibit the same robust effect (2-7-fold shift for ip and combo, 2-3-fold shift for sc). Our results suggest that CpG ODN 1826 is a highly potent adjuvant, and injection routes should be considered for development of small molecule-protein conjugate vaccines. Lastly, this study has established a new standard for assessing drugs of abuse vaccines, wherein a full dose-response curve should be performed in an appropriate behavioral task.

  3. Injection Route and TLR9 Agonist Addition Significantly Impact Heroin Vaccine Efficacy

    PubMed Central

    2015-01-01

    Active immunization is an effective means of blocking the pharmacodynamic effects of drugs and holds promise as a treatment for heroin addiction. Previously, we demonstrated the efficacy of our first-generation vaccine in blocking heroin self-administration in rats, however, many vaccine components can be modified to further improve performance. Herein we examine the effects of varying heroin vaccine injection route and adjuvant formulation. Mice immunized via subcutaneous (sc) injection exhibited inferior anti-heroin titers compared to intraperitoneal (ip) and sc/ip coadministration injection routes. Addition of TLR9 agonist cytosine-guanine oligodeoxynucleotide 1826 (CpG ODN 1826) to the original alum adjuvant elicited superior antibody titers and opioid affinities compared to alum alone. To thoroughly assess vaccine efficacy, full dose–response curves were generated for heroin-induced analgesia in both hot plate and tail immersion tests. Mice treated with CpG ODN 1826 exhibited greatly shifted dose–response curves (10–13-fold vs unvaccinated controls) while non-CpG ODN vaccine groups did not exhibit the same robust effect (2–7-fold shift for ip and combo, 2–3-fold shift for sc). Our results suggest that CpG ODN 1826 is a highly potent adjuvant, and injection routes should be considered for development of small molecule–protein conjugate vaccines. Lastly, this study has established a new standard for assessing drugs of abuse vaccines, wherein a full dose–response curve should be performed in an appropriate behavioral task. PMID:24517171

  4. The Significance of Blackstone's Understanding of Sovereign Immunity for America's Public Institutions of Higher Education.

    ERIC Educational Resources Information Center

    Snow, Brian A.; Thro, William E.

    2001-01-01

    Asserts that from the perspective of America's public institutions of higher education, Blackstone's greatest legacy is his understanding of sovereign immunity. Explores the similarities between Blackstone's understanding of sovereign immunity and the current jurisprudence of the U.S. Supreme Court. (EV)

  5. Significance of neuro-cardiac control mechanisms governed by higher regions of the brain.

    PubMed

    Taggart, Peter; Critchley, Hugo; van Duijvendoden, Stefan; Lambiase, Pier D

    2016-08-01

    Advances in investigative techniques have led to an increasing awareness and understanding of the role of central neural control in the autonomic nervous system regulation of the heart. Substantial evidence exists for a role of the higher centres in neuro-cardiac control including the effect of focal brain stimulation and acute brain lesions on cardiac electrophysiology, blood pressure, contractile function and the development of arrhythmias. Mental stress and strong emotions have long been associated with sudden cardiac death. There is an emerging literature relating the gene-environment interactions in determining the neural patterning responsible for the stress response itself. The role of the higher brain centres in determining myocardial behaviour has become accessible through the utilisation of optogenetic techniques to modulate activity in specific brainstem nuclei, enabling the dissection of specific vagal and sympathetic inputs on cardiac electrophysiology and arrhythmogenesis. Central cardiac control mechanisms are modulated by afferent signals from the heart. Ascending interoceptive pathways from heart to several forebrain regions influence the behavioural response and autonomic output to the heart. These processes are expressed as control loops at multiple levels of the neuraxis and are assumed to converge in part at the level of the baroreflex to shape the efferent drive to the heart and vasculature. PMID:27595200

  6. Tacrolimus dose requirement in renal transplant recipients is significantly higher when used in combination with corticosteroids

    PubMed Central

    Hesselink, Dennis A; Ngyuen, Hien; Wabbijn, Marike; Gregoor, Peter J H Smak; Steyerberg, Ewout W; van Riemsdijk, Iza C; Weimar, Willem; van Gelder, Teun

    2003-01-01

    Aims To evaluate the effect of corticosteroids on tacrolimus pharmacokinetics. Methods In a randomized trial, kidney transplant recipients were treated with tacrolimus and mycophenolate mofetil with either daclizumab (n = 31) or 3 months of prednisone (n = 34). Tacrolimus dose-adjusted predose concentrations (C0) at month 1–6 were compared between both groups and within the corticosteroid group before and after prednisone withdrawal. Results At month 1 the tacrolimus dose-adjusted C0 in the corticosteroid group was 83 ± 8 vs 119 ± 17 ng ml−1 mg−1 kg−1 in the daclizumab group. The tacrolimus dose-adjusted C0 within the corticosteroid group at month 1 and 2 was 42% and 29% lower compared with month 4 (P < 0.001). Conclusions A higher tacrolimus dose is required to reach target concentrations when used in combination with corticosteroids. PMID:12919182

  7. Spatially resolved flux measurements of NOx from London suggest significantly higher emissions than predicted by inventories.

    PubMed

    Vaughan, Adam R; Lee, James D; Misztal, Pawel K; Metzger, Stefan; Shaw, Marvin D; Lewis, Alastair C; Purvis, Ruth M; Carslaw, David C; Goldstein, Allen H; Hewitt, C Nicholas; Davison, Brian; Beevers, Sean D; Karl, Thomas G

    2016-07-18

    To date, direct validation of city-wide emissions inventories for air pollutants has been difficult or impossible. However, recent technological innovations now allow direct measurement of pollutant fluxes from cities, for comparison with emissions inventories, which are themselves commonly used for prediction of current and future air quality and to help guide abatement strategies. Fluxes of NOx were measured using the eddy-covariance technique from an aircraft flying at low altitude over London. The highest fluxes were observed over central London, with lower fluxes measured in suburban areas. A footprint model was used to estimate the spatial area from which the measured emissions occurred. This allowed comparison of the flux measurements to the UK's National Atmospheric Emissions Inventory (NAEI) for NOx, with scaling factors used to account for the actual time of day, day of week and month of year of the measurement. The comparison suggests significant underestimation of NOx emissions in London by the NAEI, mainly due to its under-representation of real world road traffic emissions. A comparison was also carried out with an enhanced version of the inventory using real world driving emission factors and road measurement data taken from the London Atmospheric Emissions Inventory (LAEI). The measurement to inventory agreement was substantially improved using the enhanced version, showing the importance of fully accounting for road traffic, which is the dominant NOx emission source in London. In central London there was still an underestimation by the inventory of 30-40% compared with flux measurements, suggesting significant improvements are still required in the NOx emissions inventory.

  8. Spatially resolved flux measurements of NOx from London suggest significantly higher emissions than predicted by inventories.

    PubMed

    Vaughan, Adam R; Lee, James D; Misztal, Pawel K; Metzger, Stefan; Shaw, Marvin D; Lewis, Alastair C; Purvis, Ruth M; Carslaw, David C; Goldstein, Allen H; Hewitt, C Nicholas; Davison, Brian; Beevers, Sean D; Karl, Thomas G

    2016-07-18

    To date, direct validation of city-wide emissions inventories for air pollutants has been difficult or impossible. However, recent technological innovations now allow direct measurement of pollutant fluxes from cities, for comparison with emissions inventories, which are themselves commonly used for prediction of current and future air quality and to help guide abatement strategies. Fluxes of NOx were measured using the eddy-covariance technique from an aircraft flying at low altitude over London. The highest fluxes were observed over central London, with lower fluxes measured in suburban areas. A footprint model was used to estimate the spatial area from which the measured emissions occurred. This allowed comparison of the flux measurements to the UK's National Atmospheric Emissions Inventory (NAEI) for NOx, with scaling factors used to account for the actual time of day, day of week and month of year of the measurement. The comparison suggests significant underestimation of NOx emissions in London by the NAEI, mainly due to its under-representation of real world road traffic emissions. A comparison was also carried out with an enhanced version of the inventory using real world driving emission factors and road measurement data taken from the London Atmospheric Emissions Inventory (LAEI). The measurement to inventory agreement was substantially improved using the enhanced version, showing the importance of fully accounting for road traffic, which is the dominant NOx emission source in London. In central London there was still an underestimation by the inventory of 30-40% compared with flux measurements, suggesting significant improvements are still required in the NOx emissions inventory. PMID:27098421

  9. Analytical representation of the higher virial coefficients of binary mixtures of additive hard spheres

    NASA Astrophysics Data System (ADS)

    Barrio, C.; Solana, J. R.

    2003-01-01

    Approximate expressions for the fourth and fifth virial coefficients of binary hard-sphere fluid mixtures are derived. The procedure used to obtain these expressions is based on that previously proposed by Wheatley [J. chem. Phys., 111, 5455 (1999)], but slightly modified. Wheatley's procedure starts from a prescribed general analytical form of the virial coefficients, from which the particular expression for each virial coefficient is obtained by imposing to the general form a number of limiting conditions. Here, we propose an alternative general expression of the virial coefficients and derive one more condition. This condition is satisfied when the fourth and fifth virial coefficients are expressed in the form we propose, but not when they are expressed in Wheatley's form. The agreement of the proposed analytical expressions with exact numerical data is excellent. The procedure can be extended to higher virial coefficients, although the lack of exact numerical data prevents any comparison.

  10. Gluten-free dough-making of specialty breads: Significance of blended starches, flours and additives on dough behaviour.

    PubMed

    Collar, Concha; Conte, Paola; Fadda, Costantino; Piga, Antonio

    2015-10-01

    The capability of different gluten-free (GF) basic formulations made of flour (rice, amaranth and chickpea) and starch (corn and cassava) blends, to make machinable and viscoelastic GF-doughs in absence/presence of single hydrocolloids (guar gum, locust bean and psyllium fibre), proteins (milk and egg white) and surfactants (neutral, anionic and vegetable oil) have been investigated. Macroscopic (high deformation) and macromolecular (small deformation) mechanical, viscometric (gelatinization, pasting, gelling) and thermal (gelatinization, melting, retrogradation) approaches were performed on the different matrices in order to (a) identify similarities and differences in GF-doughs in terms of a small number of rheological and thermal analytical parameters according to the formulations and (b) to assess single and interactive effects of basic ingredients and additives on GF-dough performance to achieve GF-flat breads. Larger values for the static and dynamic mechanical characteristics and higher viscometric profiles during both cooking and cooling corresponded to doughs formulated with guar gum and Psyllium fibre added to rice flour/starch and rice flour/corn starch/chickpea flour, while surfactant- and protein-formulated GF-doughs added to rice flour/starch/amaranth flour based GF-doughs exhibited intermediate and lower values for the mechanical parameters and poorer viscometric profiles. In addition, additive-free formulations exhibited higher values for the temperature of both gelatinization and retrogradation and lower enthalpies for the thermal transitions. Single addition of 10% of either chickpea flour or amaranth flour to rice flour/starch blends provided a large GF-dough hardening effect in presence of corn starch and an intermediate effect in presence of cassava starch (chickpea), and an intermediate reinforcement of GF-dough regardless the source of starch (amaranth). At macromolecular level, both chickpea and amaranth flours, singly added, determined

  11. Gluten-free dough-making of specialty breads: Significance of blended starches, flours and additives on dough behaviour.

    PubMed

    Collar, Concha; Conte, Paola; Fadda, Costantino; Piga, Antonio

    2015-10-01

    The capability of different gluten-free (GF) basic formulations made of flour (rice, amaranth and chickpea) and starch (corn and cassava) blends, to make machinable and viscoelastic GF-doughs in absence/presence of single hydrocolloids (guar gum, locust bean and psyllium fibre), proteins (milk and egg white) and surfactants (neutral, anionic and vegetable oil) have been investigated. Macroscopic (high deformation) and macromolecular (small deformation) mechanical, viscometric (gelatinization, pasting, gelling) and thermal (gelatinization, melting, retrogradation) approaches were performed on the different matrices in order to (a) identify similarities and differences in GF-doughs in terms of a small number of rheological and thermal analytical parameters according to the formulations and (b) to assess single and interactive effects of basic ingredients and additives on GF-dough performance to achieve GF-flat breads. Larger values for the static and dynamic mechanical characteristics and higher viscometric profiles during both cooking and cooling corresponded to doughs formulated with guar gum and Psyllium fibre added to rice flour/starch and rice flour/corn starch/chickpea flour, while surfactant- and protein-formulated GF-doughs added to rice flour/starch/amaranth flour based GF-doughs exhibited intermediate and lower values for the mechanical parameters and poorer viscometric profiles. In addition, additive-free formulations exhibited higher values for the temperature of both gelatinization and retrogradation and lower enthalpies for the thermal transitions. Single addition of 10% of either chickpea flour or amaranth flour to rice flour/starch blends provided a large GF-dough hardening effect in presence of corn starch and an intermediate effect in presence of cassava starch (chickpea), and an intermediate reinforcement of GF-dough regardless the source of starch (amaranth). At macromolecular level, both chickpea and amaranth flours, singly added, determined

  12. Does the addition of writing into a pharmacy communication skills course significantly impact student communicative learning outcomes? A pilot study.

    PubMed

    Lonie, John M; Rahim, Hamid

    2010-12-01

    The objective of this study was to determine if the addition of a reflective writing component in a fourth year (P-2) pharmacy communication skills course would significantly affect 2 measures of learning: (1) objective multiple choice examination questions and (2) a patient counseling Objective Structured Clinical Examination (OSCE) score. Using a nonequivalent group quasi-experimental retrospective comparison design, 98 randomly selected final examination scores from students taking a non-writing intensive (NWI) communication skills course were compared with 112 randomly selected final examination scores from students that took a communication skills course in which students engaged in several reflective writing assignments. In addition, 91 randomly selected patient counseling OSCE scores from a NWI course were statistically compared with 112 scores from students that took the writing intensive (WI) course. There were statistically significant improvements in multiple choice examination scores in the group that took the reflective writing communication skills course. There was not a statistically significant difference in patient counseling OSCE scores after students completed the WI course. Studying the effects of using reflective writing assignments in communication skills courses may improve the retention and retrieval of information presented within the course.

  13. Mechanical and Electrical Properties of a Polyimide Film Significantly Enhanced by the Addition of Single-Wall Carbon Nanotubes

    NASA Technical Reports Server (NTRS)

    Meador, Michael A.

    2005-01-01

    Single-wall carbon nanotubes have been shown to possess a combination of outstanding mechanical, electrical, and thermal properties. The use of carbon nanotubes as an additive to improve the mechanical properties of polymers and/or enhance their thermal and electrical conductivity has been a topic of intense interest. Nanotube-modified polymeric materials could find a variety of applications in NASA missions including large-area antennas, solar arrays, and solar sails; radiation shielding materials for vehicles, habitats, and extravehicular activity suits; and multifunctional materials for vehicle structures and habitats. Use of these revolutionary materials could reduce vehicle weight significantly and improve vehicle performance and capabilities.

  14. Significant reserve additions from oligocene Hackberry Sands utilizing 3-D seismic, upper Texas and Louisiana Gulf Coast

    SciTech Connect

    Zamboras, R.L.

    1995-10-01

    The Oligocene Hackberry sands of the Hackberry Embayment represent a complex and elusive exploration target. 3-D seismic evaluation along the headward erosional limits of the embayment provides a reconstructive framework of tectonic and sedimentation patterns which facilitate hydrocarbon exploration. The 3-D seismic along the Orange County, Texas portion of the Oligocene Hackberry trend indicates: (1) similarities of Hackberry structural and depositional setting to that of the underlying Eocene Yegua Formation; (2) four distinct cyclical sedimentation episodes associated with basin floor slump faulting: (3) the usefulness of seismic attributes as direct hydrocarbon indicators, and (4) the potential for significant oil and gas reserves additions in a mature trend. The Hackberry embayment represents a microcosm of the basin structural and depositional processes. Utilizing 3-D seismic to lower risk and finding cost will renew interest in trends such as the Hackberry of the Upper Texas-Louisiana Gulf Coast.

  15. Appropriate Fe (II) Addition Significantly Enhances Anaerobic Ammonium Oxidation (Anammox) Activity through Improving the Bacterial Growth Rate

    PubMed Central

    Liu, Yiwen; Ni, Bing-Jie

    2015-01-01

    The application of anaerobic ammonium oxidation (Anammox) process is often limited by the slow growth rate of Anammox bacteria. As the essential substrate element that required for culturing Anammox sludge, Fe (II) is expected to affect Anammox bacterial growth. This work systematically studied the effects of Fe (II) addition on Anammox activity based on the kinetic analysis of specific growth rate using data from batch tests with an enriched Anammox sludge at different dosing levels. Results clearly demonstrated that appropriate Fe (II) dosing (i.e., 0.09 mM) significantly enhanced the specific Anammox growth rate up to 0.172 d−1 compared to 0.118 d−1 at regular Fe (II) level (0.03 mM). The relationship between Fe (II) concentration and specific Anammox growth rate was found to be well described by typical substrate inhibition kinetics, which was integrated into currently well-established Anammox model to describe the enhanced Anammox growth with Fe (II) addition. The validity of the integrated Anammox model was verified using long-term experimental data from three independent Anammox reactors with different Fe (II) dosing levels. This Fe (II)-based approach could be potentially implemented to enhance the process rate for possible mainstream application of Anammox technology, in order for an energy autarchic wastewater treatment. PMID:25644239

  16. Appropriate Fe (II) Addition Significantly Enhances Anaerobic Ammonium Oxidation (Anammox) Activity through Improving the Bacterial Growth Rate

    NASA Astrophysics Data System (ADS)

    Liu, Yiwen; Ni, Bing-Jie

    2015-02-01

    The application of anaerobic ammonium oxidation (Anammox) process is often limited by the slow growth rate of Anammox bacteria. As the essential substrate element that required for culturing Anammox sludge, Fe (II) is expected to affect Anammox bacterial growth. This work systematically studied the effects of Fe (II) addition on Anammox activity based on the kinetic analysis of specific growth rate using data from batch tests with an enriched Anammox sludge at different dosing levels. Results clearly demonstrated that appropriate Fe (II) dosing (i.e., 0.09 mM) significantly enhanced the specific Anammox growth rate up to 0.172 d-1 compared to 0.118 d-1 at regular Fe (II) level (0.03 mM). The relationship between Fe (II) concentration and specific Anammox growth rate was found to be well described by typical substrate inhibition kinetics, which was integrated into currently well-established Anammox model to describe the enhanced Anammox growth with Fe (II) addition. The validity of the integrated Anammox model was verified using long-term experimental data from three independent Anammox reactors with different Fe (II) dosing levels. This Fe (II)-based approach could be potentially implemented to enhance the process rate for possible mainstream application of Anammox technology, in order for an energy autarchic wastewater treatment.

  17. Appropriate Fe (II) addition significantly enhances anaerobic ammonium oxidation (Anammox) activity through improving the bacterial growth rate.

    PubMed

    Liu, Yiwen; Ni, Bing-Jie

    2015-01-01

    The application of anaerobic ammonium oxidation (Anammox) process is often limited by the slow growth rate of Anammox bacteria. As the essential substrate element that required for culturing Anammox sludge, Fe (II) is expected to affect Anammox bacterial growth. This work systematically studied the effects of Fe (II) addition on Anammox activity based on the kinetic analysis of specific growth rate using data from batch tests with an enriched Anammox sludge at different dosing levels. Results clearly demonstrated that appropriate Fe (II) dosing (i.e., 0.09 mM) significantly enhanced the specific Anammox growth rate up to 0.172 d(-1) compared to 0.118 d(-1) at regular Fe (II) level (0.03 mM). The relationship between Fe (II) concentration and specific Anammox growth rate was found to be well described by typical substrate inhibition kinetics, which was integrated into currently well-established Anammox model to describe the enhanced Anammox growth with Fe (II) addition. The validity of the integrated Anammox model was verified using long-term experimental data from three independent Anammox reactors with different Fe (II) dosing levels. This Fe (II)-based approach could be potentially implemented to enhance the process rate for possible mainstream application of Anammox technology, in order for an energy autarchic wastewater treatment. PMID:25644239

  18. [Endarterectomy more favourable than stenting in symptomatic significant carotid stenosis: higher risk of ischaemic stroke or death following stenting].

    PubMed

    Meerwaldt, Robbert; Beuk, Roland J; Huisman, Ad B; Manschot, Sanne M; Zeebregts, Clark J; Geelkerken, Robert H

    2011-01-01

    Carotid endarterectomy (CEA) has proven its value in the treatment of patients with recent significant carotid artery stenosis. Percutaneous transluminal angioplasty with carotid artery stenting ('stenting' in short) is an alternative to CEA. The results of stenting and CEA in patients with symptomatic significant carotid artery stenosis were evaluated in 9 prospective randomized controlled trials and 11 meta-analyses. Almost all of these trials failed to show superiority of stenting to CEA. According to the 4 largest and most recent studies in this field the risk of a stroke or death within 30 days after the intervention is considerably higher following stenting than following CEA. In the long run the results of stenting and CEA seem to be comparable. CEA remains the gold standard in treatment of significant carotid artery stenosis, in particular in patients older than 70. PMID:21329537

  19. [Endarterectomy more favourable than stenting in symptomatic significant carotid stenosis: higher risk of ischaemic stroke or death following stenting].

    PubMed

    Meerwaldt, Robbert; Beuk, Roland J; Huisman, Ad B; Manschot, Sanne M; Zeebregts, Clark J; Geelkerken, Robert H

    2011-01-01

    Carotid endarterectomy (CEA) has proven its value in the treatment of patients with recent significant carotid artery stenosis. Percutaneous transluminal angioplasty with carotid artery stenting ('stenting' in short) is an alternative to CEA. The results of stenting and CEA in patients with symptomatic significant carotid artery stenosis were evaluated in 9 prospective randomized controlled trials and 11 meta-analyses. Almost all of these trials failed to show superiority of stenting to CEA. According to the 4 largest and most recent studies in this field the risk of a stroke or death within 30 days after the intervention is considerably higher following stenting than following CEA. In the long run the results of stenting and CEA seem to be comparable. CEA remains the gold standard in treatment of significant carotid artery stenosis, in particular in patients older than 70.

  20. Additional Value of Transluminal Attenuation Gradient in CT Angiography to Predict Hemodynamic Significance of Coronary Artery Stenosis

    PubMed Central

    Stuijfzand, Wynand J.; Danad, Ibrahim; Raijmakers, Pieter G.; Marcu, C. Bogdan; Heymans, Martijn W.; van Kuijk, Cornelis C.; van Rossum, Albert C.; Nieman, Koen; Min, James K.; Leipsic, Jonathon; van Royen, Niels; Knaapen, Paul

    2015-01-01

    OBJECTIVES The current study evaluates the incremental value of transluminal attenuation gradient (TAG), TAG with corrected contrast opacification (CCO), and TAG with exclusion of calcified coronary segments (ExC) over coronary computed tomography angiogram (CTA) alone using fractional flow reserve (FFR) as the gold standard. BACKGROUND TAG is defined as the contrast opacification gradient along the length of a coronary artery on a coronary CTA. Preliminary data suggest that TAG provides additional functional information. Interpretation of TAG is hampered by multiple heartbeat acquisition algorithms and coronary calcifications. Two correction models have been proposed based on either dephasing of contrast delivery by relating coronary density to corresponding descending aortic opacification (TAG-CCO) or excluding calcified coronary segments (TAG-ExC). METHODS Eighty-five patients with intermediate probability of coronary artery disease were prospectively included. All patients underwent step-and-shoot 256-slice coronary CTA. TAG, TAG-CCO, and TAG-ExC analyses were performed followed by invasive coronary angiography in conjunction with FFR measurements of all major coronary branches. RESULTS Thirty-four patients (40%) were diagnosed with hemodynamically-significant coronary artery disease (i.e., FFR ≤0.80). On a per-vessel basis (n = 253), 59 lesions (23%) were graded as hemodynamically significant, and the diagnostic accuracy of coronary CTA (diameter stenosis ≥50%) was 95%, 75%, 98%, and 54% for sensitivity, specificity, negative predictive value, and positive predictive value, respectively. TAG and TAG-ExC did not discriminate between vessels with or without hemodynamically significant lesions (−13.5 ± 17.1 HU [Hounsfield units] × 10 mm−1 vs. −11.6 ± 13.3 HU × 10 mm−1, p = 0.36; and 13.1 ± 15.9 HU × 10 mm−1 vs. −11.4 ± 11.7 HU × 10 mm−1, p = 0.77, respectively). TAG-CCO was lower in vessels with a hemodynamically-significant lesion (−0

  1. Reoxygenation of Asphyxiated Newborn Piglets: Administration of 100% Oxygen Causes Significantly Higher Apoptosis in Cortical Neurons, as Compared to 21%

    PubMed Central

    Faa, G.; Fanos, V.; Fanni, D.; Gerosa, C.; Faa, A.; Fraschini, M.; Pais, M. E.; Di Felice, E.; Papalois, A.; Varsami, M.; Xanthos, T.; Iacovidou, N.

    2014-01-01

    Objective. Evaluation of neuronal changes in an animal experimental model of normocapnic hypoxia- reoxygenation. Materials and Methods. Fifty male piglets were the study subjects; normocapnic hypoxia was induced in 40 piglets and ten were sham-operated (controls). When bradycardia and/or severe hypotension occurred, reoxygenation was initiated. Animals were allocated in 4 groups according to the oxygen concentration, they were resuscitated with 18%, 21%, 40%, and 100% O2. Persisting asystole despite 10 minutes of cardiopulmonary resuscitation and return of spontaneous circulation were the endpoints of the experiment. Surviving animals were euthanized and brain cortex samples were collected, hematoxylin and eosin-stained, and examined for apoptotic bodies observing 10 consecutive high power fields. Results. Histological examination of the control group did not show any pathological change. On the contrary, apoptosis of neurons was found in 87.5% of treated animals. When specimens were examined according to the oxygen concentration used for resuscitation, we found marked intergroup variability; a higher percentage of apoptotic neurons was observed in piglets of group 4 (100% oxygen) compared to the others (P = 0.001). Conclusions. This preliminary data shows that normocapnic hypoxia and reoxygenation in Landrace/Large White piglets resulted in significant histological changes in the brain cortex. The degree of pathological changes in cortical neurons was significantly associated with the oxygen concentration used for reoxygenation, with a higher percentage of apoptotic neurons being observed in piglets reoxygenated with 100% compared to 18% O2 and to 21% O2. PMID:24783208

  2. Higher Physical Activity Is Associated With Lower Aortic Stiffness but Not With Central Blood Pressure: The ADDITION-Pro Study

    PubMed Central

    Laursen, Anne Sofie Dam; Hansen, Anne-Louise Smidt; Wiinberg, Niels; Brage, Søren; Sandbæk, Annelli; Lauritzen, Torsten; Witte, Daniel R.; Jørgensen, Marit Eika; Johansen, Nanna Borup

    2015-01-01

    Abstract Physical activity is associated with reduced cardiovascular disease risk. However, improvements in conventional risk factors due to physical activity do not explain its full benefit. Therefore, we examined associations of objectively measured physical activity energy expenditure and intensity with central hemodynamics to provide new insight into the link between physical activity and cardiovascular disease. We analyzed data from 1816 Danes (median age: 66 years) without cardiovascular disease. Physical activity was estimated using combined accelerometry and heart rate monitoring. Aortic stiffness was assessed by applanation tonometry, as aortic pulse wave velocity, and central blood pressure was estimated from radial waveforms. Associations between physical activity energy expenditure and central hemodynamics were examined by linear regression. Furthermore, the consequence of substituting 1 hour sedentary behavior with 1 hour light or moderate-to-vigorous physical activity on central hemodynamics was examined. Median physical activity energy expenditure was 28.0 kJ/kg/d (IQR: 19.8; 38.7). A 10 kJ/kg/d higher energy expenditure was associated with 0.75% lower aortic pulse wave velocity (CI: −1.47; −0.03). Associations with central systolic blood pressure and central pulse pressure were not statistically significant. We observed no difference in central hemodynamics when substituting 1 hour sedentary behavior with 1 hour light or moderate-to-vigorous physical activity. In this relatively inactive population, higher physical activity energy expenditure was associated with lower aortic stiffness, while there was no statistically significant association between substitution of activity intensity and central hemodynamics. This suggests that lower aortic stiffness is one of a number of health benefits attributed to higher habitual physical activity. PMID:25654392

  3. Fertilizer addition lessens the flux of microbial carbon to higher trophic levels in soil food webs of grassland.

    PubMed

    Lemanski, Kathleen; Scheu, Stefan

    2014-10-01

    Roots and root-derived C compounds are increasingly recognised as important resources for soil animal food webs. We used (13)C-labelled glucose as a model C compound representing root exudates to follow the incorporation of root-derived C into the soil animal food web of a temperate grassland over a period of 52 weeks. We investigated variations in glucose C incorporation with fertilizer addition and sward composition, i.e. variations in plant functional groups. The approach allowed the differentiation of trophic chains based on primary decomposers feeding on litter and phytophagous species feeding on roots (i.e. not incorporating glucose C) from those based on secondary decomposers feeding on microorganisms (thereby assimilating glucose C). Each of the studied soil animal species incorporated glucose C, indicating that the majority of grassland soil animal species rely on microorganisms as food resources with microorganisms being fuelled by root exudates. However, incorporation of glucose C into soil animal species varied markedly with species identity, suggesting that detritivorous microarthropods complement each other in channelling microbial C through soil food webs. Fertilizer addition markedly reduced the concentration of glucose C in most soil animal species as well as the absolute transfer of glucose C into oribatid mites as major secondary decomposers. The results suggest that fertilizer addition shifts the basis of the decomposer food web towards the use of unlabelled resources, presumably roots, i.e. towards a herbivore system, thereby lessening the link between microorganisms and microbial grazers and hampering the propagation of microbial C to higher trophic levels.

  4. Significance of Additional Non-Mass Enhancement in Patients with Breast Cancer on Preoperative 3T Dynamic Contrast Enhanced MRI of the Breast

    PubMed Central

    Cho, Yun Hee; Cho, Kyu Ran; Park, Eun Kyung; Seo, Bo Kyoung; Woo, Ok Hee; Cho, Sung Bum; Bae, Jeoung Won

    2016-01-01

    Background In preoperative assessment of breast cancer, MRI has been shown to identify more additional breast lesions than are detectable using conventional imaging techniques. The characterization of additional lesions is more important than detection for optimal surgical treatment. Additional breast lesions can be included in focus, mass, and non-mass enhancement (NME) on MRI. According to the fifth edition of the breast imaging reporting and data system (BI-RADS®), which includes several changes in the NME descriptors, few studies to date have evaluated NME in preoperative assessment of breast cancer. Objectives We investigated the diagnostic accuracy of BI-RADS descriptors in predicting malignancy for additional NME lesions detected on preoperative 3T dynamic contrast enhanced MRI (DCE-MRI) in patients with newly diagnosed breast cancer. Patients and Methods Between January 2008 and December 2012, 88 patients were enrolled in our study, all with NME lesions other than the index cancer on preoperative 3T DCE-MRI and all with accompanying histopathologic examination. The MRI findings were analyzed according to the BI-RADS MRI lexicon. We evaluated the size, distribution, internal enhancement pattern, and location of NME lesions relative to the index cancer (i.e., same quadrant, different quadrant, or contralateral breast). Results On histopathologic analysis of the 88 NME lesions, 73 (83%) were malignant and 15 (17%) were benign. Lesion size did not differ significantly between malignant and benign lesions (P = 0.410). Malignancy was more frequent in linear (P = 0.005) and segmental (P = 0.011) distributions, and benignancy was more frequent in focal (P = 0.004) and regional (P < 0.001) NME lesions. The highest positive predictive value (PPV) for malignancy occurred in segmental (96.8%), linear (95.1%), clustered ring (100%), and clumped (92.0%) enhancement. Asymmetry demonstrated a high positive predictive value of 85.9%. The frequency of malignancy was higher

  5. Significance of Trends on Enrolment, Budget and Actual Expenditure in the Examination of Higher Education Financing in Tanzania

    ERIC Educational Resources Information Center

    Memba, Albert Zephaniah; Feng, Zhao Jun

    2016-01-01

    Financing of higher education in Tanzania is considered a crucial factor in realizing the country's development vision. It is for these reasons that Tanzania has been financing its higher education since its inception. Diminishing resource capacity and competing interests for government finance plunged the higher education into financial doldrums.…

  6. Tribes and Territories in the 21st Century: Rethinking the Significance of Disciplines in Higher Education. International Studies in Higher Education

    ERIC Educational Resources Information Center

    Trowler, Paul, Ed.; Saunders, Murray, Ed.; Bamber, Veronica, Ed.

    2012-01-01

    The "tribes and territories" metaphor for the cultures of academic disciplines and their roots in different knowledge characteristics has been used by those interested in university life and work since the early 1990s. This book draws together research, data and theory to show how higher education has gone through major change since then and how…

  7. Judgments of learning are significantly higher following feedback on relatively good versus relatively poor trials despite no actual learning differences.

    PubMed

    Carter, Michael J; Smith, Victoria; Ste-Marie, Diane M

    2016-02-01

    Studies have consistently shown that prospective metacognitive judgments of learning are often inaccurate because humans mistakenly interpret current performance levels as valid indices of learning. These metacognitive discrepancies are strongly related to conditions of practice. Here, we examined how the type of feedback (after good versus poor trials) received during practice and awareness (aware versus unaware) of this manipulation affected judgments of learning and actual learning. After each six-trial block, participants received feedback on their three best trials or three worst trials and half of the participants were made explicitly aware of the type of feedback they received while the other half were unaware. Judgments of learning were made at the end of each six-trial block and before the 24-h retention test. Results indicated no motor performance differences between groups in practice or retention; however, receiving feedback on relatively good compared to relatively poor trials resulted in significantly higher judgments of learning in practice and retention, irrespective of awareness. These results suggest that KR on relatively good versus relatively poor trials can have dissociable effects on judgments of learning in the absence of actual learning differences, even when participants are made aware of their feedback manipulation.

  8. How Different Are Higher Education Institutions in the UK, US and Australia? The Significance of Government Involvement

    ERIC Educational Resources Information Center

    Moodie, Gavin

    2015-01-01

    Governments in the UK and many other countries have long sought to promote the diversity of their higher education institutions. However, diversity is hard to define, harder to measure and even more difficult to compare between countries. Most empirical analyses of the diversity of higher education systems use categorical variables, which shape…

  9. Funding for Higher Education in Asia and the Pacific. Strategies To Increase Cost Efficiency and Attract Additional Financial Support.

    ERIC Educational Resources Information Center

    Harman, Grant, Ed.; Selim, M., Ed.

    This book presents articles that document the serious funding problems faced by higher education institutions and systems in the Asian and Pacific region, and explores possible strategies to address these problems. It presents an overview of the financial situation faced by higher education in the region, and then discusses two main strategies…

  10. Higher Education in the United Arab Emirates: An Analysis of the Outcomes of Significant Increases in Supply and Competition

    ERIC Educational Resources Information Center

    Wilkins, Stephen

    2010-01-01

    During the last decade, several countries across the Middle and Far East have established higher education hubs, some of which have grown rapidly by attracting foreign universities to set up international branch campuses. The United Arab Emirates (UAE) is by far the largest host of international branch campuses globally, having over 40 providers…

  11. Sources of Inspiration: The role of significant persons in young people's choice of science in higher education

    NASA Astrophysics Data System (ADS)

    Sjaastad, Jørgen

    2012-07-01

    The objectives of this article were to investigate to which extent and in what ways persons influence students' choice of science, technology, engineering, and mathematics (STEM) in tertiary education, and to assess the suitability of an analytical framework for describing this influence. In total, 5,007 Norwegian STEM students completed a questionnaire including multiple-choice as well as open-ended questions about sources of inspiration for their educational choice. Using the conceptualisation of significant persons suggested by Woelfel and Haller, the respondents' descriptions of parents and teachers are presented in order to elaborate on the different ways these significant persons influence a STEM-related educational choice. Parents engaged in STEM themselves are models, making the choice of STEM familiar, and they help youngsters define themselves through conversation and support, thus being definers. Teachers are models by displaying how STEM might bring fulfilment in someone's life and by giving pupils a positive experience with the subjects. They help young people discover their STEM abilities, thus being definers. Celebrities are reported to have minor influence on STEM-related educational choices. Both qualitative and quantitative analyses indicate that interpersonal relationships are key factors in order to inspire and motivate a choice of STEM education. Implications for recruitment issues and for research on interpersonal influence are discussed. It is suggested that initiatives to increase recruitment to STEM might be aimed at parents and other persons in interpersonal relationships with youth as a target group.

  12. Double threshold in bi- and multilingual contexts: preconditions for higher academic attainment in English as an additional language

    PubMed Central

    Lechner, Simone; Siemund, Peter

    2014-01-01

    Bi- and multilingualism has been shown to have positive effects on the attainment of third and additional languages. These effects, however, depend on the type of bi- and multilingualism and the status of the languages involved (Cenoz, 2003; Jessner, 2006). In this exploratory trend study, we revisit Cummins' Threshold Hypothesis (1979), claiming that bilingual children must reach certain levels of attainment in order to (a) avoid academic deficits and (b) allow bilingualism to have a positive effect on their cognitive development and academic attainment. To this end, we examine the attainment of English as an academic language of 16-years-old school children from Hamburg (n = 52). Our findings support the existence of thresholds for literacy attainment. We argue that language external factors may override positive effects of bilingualism. In addition, these factors may compensate negative effects attributable to low literacy attainment in German and the heritage languages. We also show that low attainment levels in migrant children's heritage languages preempt high literacy attainment in additional languages. PMID:24926277

  13. Double threshold in bi- and multilingual contexts: preconditions for higher academic attainment in English as an additional language.

    PubMed

    Lechner, Simone; Siemund, Peter

    2014-01-01

    Bi- and multilingualism has been shown to have positive effects on the attainment of third and additional languages. These effects, however, depend on the type of bi- and multilingualism and the status of the languages involved (Cenoz, 2003; Jessner, 2006). In this exploratory trend study, we revisit Cummins' Threshold Hypothesis (1979), claiming that bilingual children must reach certain levels of attainment in order to (a) avoid academic deficits and (b) allow bilingualism to have a positive effect on their cognitive development and academic attainment. To this end, we examine the attainment of English as an academic language of 16-years-old school children from Hamburg (n = 52). Our findings support the existence of thresholds for literacy attainment. We argue that language external factors may override positive effects of bilingualism. In addition, these factors may compensate negative effects attributable to low literacy attainment in German and the heritage languages. We also show that low attainment levels in migrant children's heritage languages preempt high literacy attainment in additional languages.

  14. Low Carbon Rice Farming Practices in the Mekong Delta Yield Significantly Higher Profits and Lower Greenhouse Gas Emissions

    NASA Astrophysics Data System (ADS)

    Rudek, J.; Van Sanh, N.; Tinh, T. K.; Tin, H. Q.; Thu Ha, T.; Pha, D. N.; Cui, T. Q.; Tin, N. H.; Son, N. N.; Thanh, H. H.; Kien, H. T.; Kritee, K.; Ahuja, R.

    2014-12-01

    The Vietnam Low-Carbon Rice Project (VLCRP) seeks to significantly reduce GHG emissions from rice cultivation, an activity responsible for more than 30% of Vietnam's overall GHG emissions, while improving livelihoods for the rice farmer community by decreasing costs and enhancing yield as well as providing supplemental farmer income through the sale of carbon credits. The Mekong Delta makes up 12% of Vietnam's land area, but produces more than 50% of the country's rice, including more than 90% of the rice for export. Rice cultivation is the main source of income for 80% of farmers in the Mekong Delta. VLCRP was launched in late 2012 in the Mekong Delta in two major rice production provinces, Kien Giang and An Giang. To date, VLCRP has completed 11 crop seasons (in Kien Giang and An Giang combined), training over 400 farmer households in applying VLCRP's package of practices (known as 1 Must - 6 Reductions) and building technical capacity to its key stakeholders and rice farmer community leaders. By adopting the 1 Must- 6 Reductions practices (including reduced seeding density, reduced fertilizer and pesticide application, and alternative wetting and drying water management), rice farmers reduce their input costs while maintaining or improving yields, and decreasing greenhouse gas emissions. The VLCRP package of practices also deliver other environmental and social co-benefits, such as reduced water pollution, improved habitat for fishery resources and reduced health risks for farmers through the reduction of agri-chemicals. VLCRP farmers use significantly less inputs (50% reduction in seed, 30% reduction in fertilizer, 40-50% reduction in water) while improving yields 5-10%, leading to an increase in profit from 10% to as high as 60% per hectare. Preliminary results indicate that the 1 Must- 6 Reductions practices have led to approximately 40-65% reductions in greenhouse gas emissions, equivalent to 4 tons of CO2e/ha/yr in An Giang and 35 tons of CO2e/ha/yr in Kien

  15. Significance of higher drug concentration in erythrocytes of mice infected with Schistosoma japonicum and treated orally with mefloquine at single doses.

    PubMed

    Tao, Yi; Xue, Jian; Jiang, Bin; Zhang, Hao-Bing; Xiao, Shu-Hua

    2015-12-01

    .7 versus 10.7 ± 2.7 μg/mL) lower than that in the corresponding non-infected mice, but its level was above the determined in vitro LC95 (95 % lethal concentration) value of 6.12 μg/mL. Meanwhile, longer T 1/2 value of 159.2 ± 129.3 h in infected mice led to significant increase in AUC0-∞ value (1969.3 ± 1057.7 vs 486.4 ± 53.0 μg/mL·h), relative to corresponding non-infected mice. In addition, the mean residence time (MRT0-∞) in infected mice was also significantly longer than that in non-infected mice. All these results may beneficial for the treatment. According to the results, we suggest that higher ratios of mefloquine concentration in erythrocytes to plasma may offer a way to transport mefloquine to the worm gut through ingestion of erythrocytes by the worms, where the gut is the site for displaying the effect by mefloquine.

  16. Developing the Understanding and Practice of Inclusion in Higher Education for International Students with Disabilities/Additional Needs: A Whole Schooling Approach

    ERIC Educational Resources Information Center

    Supple, Briony; Abgenyega, Joseph

    2011-01-01

    In this paper we present research on inclusion in higher education using a whole schooling philosophy. We seek insight into the perspectives of international students with disabilities/additional needs, three of whom from this particular research group are from non-English speaking backgrounds and attending the same university in Melbourne,…

  17. Administrators' Perceptions of Factors Related to Student Retention at Colleges with a Significant Black Student Enrollment Affiliated with the Association for Biblical Higher Education

    ERIC Educational Resources Information Center

    Wilson, Wesley B.

    2013-01-01

    This study described and explored the factors perceived as relevant to student retention by administrators at colleges and universities with significant Black student populations. The sample was 31 institutions affiliated with the Association for Biblical Higher Education (ABHE) that had Black student enrollment of 20% or more. The study sought to…

  18. Tribological characteristics of bisphenol AF bis(diphenyl phosphate) as an antiwear additive in polyalkylene glycol and polyurea grease for significantly improved lubrication

    NASA Astrophysics Data System (ADS)

    Zhu, Lili; Wu, Xinhu; Zhao, Gaiqing; Wang, Xiaobo

    2016-02-01

    A new antiwear additive of Bisphenol AF bis(diphenyl phosphate) (BAFDP) was synthesized and characterized. The tribological behaviors of the additive for polyalkylene glycol (PAG) and polyurea grease (PG) application in steel/steel contacts were evaluated on an Optimol SRV-IV oscillating reciprocating friction and wear tester at elevated temperature. The results revealed that BAFDP could drastically reduce friction and wear of sliding pairs in both PAG and also in PG at 100 °C. The tribological properties of BAFDP are superior to the normally used zinc dialkyldithiophosphate-based additive package (ZDDP) in PAG and PG. Moreover, BAFDP as additive for PAG and PG displays relatively significant tribological properties in temperature-ramp tests by performing well at 50-300 °C, indicating the excellent high temperature friction reduction and anti-wear capacity of BAFDP. XPS results showed that boundary lubrication films composed of Fe(OH)O, Fe3O4, FePO4, FeF2, FeF3, compounds containing the Psbnd O bonds, nitrogen oxide, and so forth, were formed on the worn surface, which contributed to excellent friction reduction and antiwear performance.

  19. A Study to Determine if Addition of Palatal Petechiae to Centor Criteria Adds More Significance to Clinical Diagnosis of Acute Strep Pharyngitis in Children.

    PubMed

    Nibhanipudi, Kumara V

    2016-01-01

    Objective. A study to determine if addition of palatal petechiae to Centor criteria adds more value for clinical diagnosis of acute strep pharyngitis in children. Hypothesis. In children, Centor Criteria does not cover all the symptoms and signs of acute strep pharyngitis. We hypothesize that addition of palatal petechiae to Centor Criteria will increase the possibility of clinical diagnosis of group A streptococcal pharyngitis in children. Methods. One hundred patients with a complaint of sore throat were enrolled in the study. All the patients were examined clinically using the Centor Criteria. They were also examined for other signs and symptoms like petechial lesions over the palate, abdominal pain, and skin rash. All the patients were given rapid strep tests, and throat cultures were sent. No antibiotics were given until culture results were obtained. Results. The sample size was 100 patients. All 100 had fever, sore throat, and erythema of tonsils. Twenty of the 100 patients had tonsillar exudates, 85/100 had tender anterior cervical lymph nodes, and 86/100 had no cough. In total, 9 out of the 100 patients had positive throat cultures. We observed that petechiae over the palate, a very significant sign, is not included in the Centor Criteria. Palatal petechiae were present in 8 out of the 100 patients. Six out of these 8 with palatal petechiae had positive throat culture for strep (75%). Only 7 out of 20 with exudates had positive strep culture. Sixteen out of the 100 patients had rapid strep test positive. Those 84/100 who had negative rapid strep also had negative throat culture. Statistics. We used Fisher's exact test, comparing throat culture positive and negative versus presence of exudates and palatal hemorrhages with positive and negative throat cultures and the resultant P value <.0001. Conclusion. Our study concludes that addition of petechiae over the palate to Centor Criteria will increase the possibility of diagnosing acute group A streptococcal

  20. A Study to Determine if Addition of Palatal Petechiae to Centor Criteria Adds More Significance to Clinical Diagnosis of Acute Strep Pharyngitis in Children

    PubMed Central

    Nibhanipudi, Kumara V.

    2016-01-01

    Objective. A study to determine if addition of palatal petechiae to Centor criteria adds more value for clinical diagnosis of acute strep pharyngitis in children. Hypothesis. In children, Centor Criteria does not cover all the symptoms and signs of acute strep pharyngitis. We hypothesize that addition of palatal petechiae to Centor Criteria will increase the possibility of clinical diagnosis of group A streptococcal pharyngitis in children. Methods. One hundred patients with a complaint of sore throat were enrolled in the study. All the patients were examined clinically using the Centor Criteria. They were also examined for other signs and symptoms like petechial lesions over the palate, abdominal pain, and skin rash. All the patients were given rapid strep tests, and throat cultures were sent. No antibiotics were given until culture results were obtained. Results. The sample size was 100 patients. All 100 had fever, sore throat, and erythema of tonsils. Twenty of the 100 patients had tonsillar exudates, 85/100 had tender anterior cervical lymph nodes, and 86/100 had no cough. In total, 9 out of the 100 patients had positive throat cultures. We observed that petechiae over the palate, a very significant sign, is not included in the Centor Criteria. Palatal petechiae were present in 8 out of the 100 patients. Six out of these 8 with palatal petechiae had positive throat culture for strep (75%). Only 7 out of 20 with exudates had positive strep culture. Sixteen out of the 100 patients had rapid strep test positive. Those 84/100 who had negative rapid strep also had negative throat culture. Statistics. We used Fisher’s exact test, comparing throat culture positive and negative versus presence of exudates and palatal hemorrhages with positive and negative throat cultures and the resultant P value <.0001. Conclusion. Our study concludes that addition of petechiae over the palate to Centor Criteria will increase the possibility of diagnosing acute group A streptococcal

  1. Clinical significance of the administration of cytarabine or thiotepa in addition to total body irradiation and cyclophosphamide for allogeneic hematopoietic cell transplantation in patients with acute leukemia.

    PubMed

    Tachibana, Takayoshi; Tanaka, Masatsugu; Hagihara, Maki; Kawasaki, Rika; Yamazaki, Etsuko; Koharazawa, Hideyuki; Taguchi, Jun; Tomita, Naoto; Fujimaki, Katsumichi; Sakai, Rika; Fujita, Hiroyuki; Fujisawa, Shin; Maruta, Atsuo; Ishigatsubo, Yoshiaki; Kanamori, Heiwa

    2015-10-01

    A multicenter retrospective study was performed to determine the significance of adding cytarabine (CA) or thiotepa (TT) in the context of total body irradiation (TBI) and cyclophosphamide (CY). A total of 322 patients who underwent allogeneic hematopoietic cell transplantation (HCT) were distributed to the following three groups: TBI/CY (n = 75), TBI/CY/CA (n = 77), and TBI/CY/TT (n = 170). In the TBI/CY/TT group, 164 of patients (96 %) received HCT during the previous year (2000-2005). Multivariate analysis revealed that the TBI/CY/TT group demonstrated a trend of poorer survival rate than the TBI/CY group, [hazard ratio (HR) = 1.49, 95 % confidence interval (CI) 0.99-2.24, P = 0.055] with a higher non-relapse mortality (NRM) (HR = 2.34, 95 % CI 1.35-4.06, P = 0.002) rates, while TBI/CY/CA group demonstrated similar outcomes. Even in the subgroup analyses of disease type or disease risk, the outcomes with intensified conditioning regimens were not superior to those with TBI/CY. In conclusion, although the significant bias has to be carefully considered, the clinical benefit of adding CA or TT to the TBI/CY regimen was not demonstrated.

  2. Root and shoot gas exchange respond additively to moderate ozone and methyl jasmonate without induction of ethylene: ethylene is induced at higher O3 concentrations

    PubMed Central

    Grantz, D.A.; Vu, H.-B.

    2012-01-01

    The available literature is conflicting on the potential protection of plants against ozone (O3) injury by exogenous jasmonates, including methyl jasmonate (MeJA). Protective antagonistic interactions of O3 and MeJA have been observed in some systems and purely additive effects in others. Here it is shown that chronic exposure to low to moderate O3 concentrations (4–114 ppb; 12 h mean) and to MeJA induced additive reductions in carbon assimilation (A n) and root respiration (R r), and in calculated whole plant carbon balance. Neither this chronic O3 regime nor MeJA induced emission of ethylene (ET) from the youngest fully expanded leaves. ET emission was induced by acute 3 h pulse exposure to much higher O3 concentrations (685 ppb). ET emission was further enhanced in plants treated with MeJA. Responses of growth, allocation, photosynthesis, and respiration to moderate O3 concentrations and to MeJA appear to be independent and additive, and not associated with emission of ET. These results suggest that responses of Pima cotton to environmentally relevant O3 are not mediated by signalling pathways associated with ET and MeJA, though these pathways are inducible in this species and exhibit a synergistic O3×MeJA interaction at very high O3 concentrations. PMID:22563119

  3. The addition of rituximab to fludarabine and cyclophosphamide chemotherapy results in a significant improvement in overall survival in patients with newly diagnosed mantle cell lymphoma: results of a randomized UK National Cancer Research Institute trial

    PubMed Central

    Rule, Simon; Smith, Paul; Johnson, Peter W.M.; Bolam, Simon; Follows, George; Gambell, Joanne; Hillmen, Peter; Jack, Andrew; Johnson, Stephen; Kirkwood, Amy A; Kruger, Anton; Pocock, Christopher; Seymour, John F.; Toncheva, Milena; Walewski, Jan; Linch, David

    2016-01-01

    Mantle cell lymphoma is an incurable and generally aggressive lymphoma that is more common in elderly patients. Whilst a number of different chemotherapeutic regimens are active in this disease, there is no established gold standard therapy. Rituximab has been used widely to good effect in B-cell malignancies but there is no evidence that it improves outcomes when added to chemotherapy in this disease. We performed a randomized, open-label, multicenter study looking at the addition of rituximab to the standard chemotherapy regimen of fludarabine and cyclophosphamide in patients with newly diagnosed mantle cell lymphoma. A total of 370 patients were randomized. With a median follow up of six years, rituximab improved the median progression-free survival from 14.9 to 29.8 months (P<0.001) and overall survival from 37.0 to 44.5 months (P=0.005). This equates to absolute differences of 9.0% and 22.1% for overall and progression-free survival, respectively, at two years. Overall response rates were similar, but complete response rates were significantly higher in the rituximab arm: 52.7% vs. 39.9% (P=0.014). There was no clinically significant additional toxicity observed with the addition of rituximab. Overall, approximately 18% of patients died of non-lymphomatous causes, most commonly infections. The addition of rituximab to fludarabine and cyclophosphamide chemotherapy significantly improves outcomes in patients with mantle cell lymphoma. However, these regimens have significant late toxicity and should be used with caution. This trial has been registered (ISRCTN81133184 and clinicaltrials.gov:00641095) and is supported by the UK National Cancer Research Network. PMID:26611473

  4. A puzzle form of a non-verbal intelligence test gives significantly higher performance measures in children with severe intellectual disability

    PubMed Central

    Bello, Katrina D; Goharpey, Nahal; Crewther, Sheila G; Crewther, David P

    2008-01-01

    Background Assessment of 'potential intellectual ability' of children with severe intellectual disability (ID) is limited, as current tests designed for normal children do not maintain their interest. Thus a manual puzzle version of the Raven's Coloured Progressive Matrices (RCPM) was devised to appeal to the attentional and sensory preferences and language limitations of children with ID. It was hypothesized that performance on the book and manual puzzle forms would not differ for typically developing children but that children with ID would perform better on the puzzle form. Methods The first study assessed the validity of this puzzle form of the RCPM for 76 typically developing children in a test-retest crossover design, with a 3 week interval between tests. A second study tested performance and completion rate for the puzzle form compared to the book form in a sample of 164 children with ID. Results In the first study, no significant difference was found between performance on the puzzle and book forms in typically developing children, irrespective of the order of completion. The second study demonstrated a significantly higher performance and completion rate for the puzzle form compared to the book form in the ID population. Conclusion Similar performance on book and puzzle forms of the RCPM by typically developing children suggests that both forms measure the same construct. These findings suggest that the puzzle form does not require greater cognitive ability but demands sensory-motor attention and limits distraction in children with severe ID. Thus, we suggest the puzzle form of the RCPM is a more reliable measure of the non-verbal mentation of children with severe ID than the book form. PMID:18671882

  5. Phase stabilization of magnetite (Fe3O4) nanoparticles with B2O3 addition: A significant enhancement on the phase transition temperature

    NASA Astrophysics Data System (ADS)

    Topal, Uğur; Aksan, Mehmet Ali

    2016-05-01

    Magnetite nanoparticles (MNPs) are extensively investigated for biomedical applications, particularly as contrast agents for Magnetic Resonance Imaging and as drug delivery agent and heat mediators for cancer therapy. Tuning the magnetic properties of the magnetite nanoparticles with doping of foreign atoms has a crucial importance for determining the application areas of these materials and so attracts much interests. On the other hand the doping with foreign atoms requires high temperature annealing, and it causes a phase transition to the hematite phase above 400 °C. In this work the phase transition temperature from the magnetite to the hematite phase has been increased by 200 °C, which is the highest enhancement reported in literature. It was achieved by addition of the appropriate amounts of B2O3. Our experiments indicates that the 5.0 wt% of B2O3 addition stabilizes and keeps the existence of single phase magnetite up to 600 °C.

  6. Significant Promotion Effect of Mo Additive on a Novel Ce-Zr Mixed Oxide Catalyst for the Selective Catalytic Reduction of NO(x) with NH3.

    PubMed

    Ding, Shipeng; Liu, Fudong; Shi, Xiaoyan; Liu, Kuo; Lian, Zhihua; Xie, Lijuan; He, Hong

    2015-05-13

    A novel Mo-promoted Ce-Zr mixed oxide catalyst prepared by a homogeneous precipitation method was used for the selective catalytic reduction (SCR) of NO(x) with NH3. The optimal catalyst showed high NH3-SCR activity, SO2/H2O durability, and thermal stability under test conditions. The addition of Mo inhibited growth of the CeO2 particle size, improved the redox ability, and increased the amount of surface acidity, especially the Lewis acidity, all of which were favorable for the excellent NH3-SCR performance. It is believed that the catalyst is promising for the removal of NO(x) from diesel engine exhaust.

  7. Stages in the Making of the Competence Approach and Its Significance to Teaching Medical Disciplines at Institutions of Higher Medical Learning

    ERIC Educational Resources Information Center

    Mayev, Igor V.; Dautova, Olga B.; Dicheva, Diana T.; Andreyev, Dmitry N.; Goncharenko, Aleksandra Yu.; Kucheryavy, Yury A.; Aleksandrova, Kseniya O.

    2014-01-01

    This article examines the preconditions and origins of the competence approach and various approaches to apprehending the essence of competencies: personal, functional, and cognitive. The authors cover the major stages in the making of the competence approach at institutions of higher medical learning.

  8. Significant Labor and Employment Law Issues in Higher Education During the Past Decade and What To Look for Now: A Union Perspective.

    ERIC Educational Resources Information Center

    Hendrickson, Rachel

    2000-01-01

    A union perspective of major issues in higher education labor law in the 1990s includes the 11th Circuit Court cases on whether Congress abrogated states' 11th Amendment immunity for suits under the Age Discrimination in Employment Act (ADEA) and under the Americans with Disabilities Act (ADA). Analyzes contract issues of protection around age…

  9. Significant Labor and Employment Law Issues in Higher Education During the Past Decade and What To Look for Now: A Management Perspective.

    ERIC Educational Resources Information Center

    Hunsicker Jr., J. Freedley

    2000-01-01

    A management perspective of major issues in higher education labor law in the 1990s addresses: sexual harassment; the Civil Rights Act of 1991; diversity on campus, elimination of mandatory retirement for faculty; development of contingent work force; and unionization of residents, interns, and graduate assistants. Predicts alternatives to…

  10. Significant Labor and Employment Law Issues in Higher Education During the Past Decade and What to Look for Now: The Perspective of an Academician.

    ERIC Educational Resources Information Center

    Bodah, Matthew M.

    2000-01-01

    An academician explores major issues in higher education labor law during the 1990s: union organizing by graduate teaching assistants, bargaining and workload issues, developments concerning grievance arbitration, and rights of individual faculty members within unions. Issues likely to arise in the next decade include alternatives to tenure,…

  11. Significance of the sexual openings and supplementary structures on the phylogeny of brachyuran crabs (Crustacea, Decapoda, Brachyura), with new nomina for higher-ranked podotreme taxa.

    PubMed

    Guinot, Danièle; Tavares, Marcos; Castro, Peter

    2013-01-01

    The patterns of complexity of the male and female sexual openings in Brachyura, which have been the source of uncertainties and conflicting opinions, are documented, together with a study of the morphologies of the coxal and sternal gonopores in both sexes, penises, spermathecae, and gonopods. The vulvae, male gonopores and penises are described among selected taxa of Eubrachyura, and their function and evolution examined in the context of a wide variety of mating behaviours. The location of female and male gonopores, the condition of the penis (coxal and sternal openings and modalities of protection), and related configurations of thoracic sternites 7 and 8, which are modified by the intercalation of a wide sternal part (thoracic sternites 7 and 8) during carcinisation, show evidence of deep homology. They represent taxonomic criteria at all ranks of the family-series and may be used to test lineages. Of particular significance are the consequences of the posterior expansion of the thoracic sternum, which influences the condition, shape, and sclerotisation of the penis, and its emergence from coxal (heterotreme) to coxo-sternal, which is actually still coxal (heterotreme), in contrast to a sternal emergence (thoracotreme). The heterotreme-thoracotreme distinction results from two different trajectories of the vas deferens and its ejaculatory duct via the P5 coxa (Heterotremata) or through the thoracic sternum (Thoracotremata). Dissections of males of several families have demonstrated that this major difference not only affects the external surface (perforation of the coxa or the sternum by the ejaculatory duct) but also the internal anatomy. There is no evidence for an ejaculatory duct passing through the articular membrane between the P5 coxa and the thoracic sternum in any Brachyura, even when the sternal male gonopore is very close to the P5 coxa. Trends towards the coxo-sternal condition are exemplified by multistate characters, varying from a shallow

  12. The effect of membrane fluidization on protein kinase C: Inhibition by ethanol and higher alcohols and stimulation by increased lipid unsaturation or addition non-esterified fatty acids

    SciTech Connect

    Cox, K.J.A.; Rubin, E.; Stubbs, C.D. )

    1992-01-01

    Protein kinase C (PKC) is a membrane bound enzyme that is dependent on calcium, anionic phospholipids, and sn-1,2-diacylglycerol (DAG) to be fully active. The relationship between membrane fluidity and PKC activity was investigated using model vesicle systems composed of phosphatidylserine alone or in combination with phosphatidylcholine. Effects on membrane fluidity were assessed using the fluorescence anisotropy of diphenylhexatriene. When membrane fluidity was increased by the addition of short chain n-alkanols, PKC activity was inhibited. There was a linear relationship for a given level of inhibition and the membrane-buffer partition coefficient. By contrast, when the degree of unsaturation in the phosphatidylcholine was increased, although the bilayer was again fluidized, PKC activity was enhanced. The addition of non-esterified fatty acid also activated PKC, either when directly added to the vesicles or when generated by the addition of exogenous phospholipase A[sub 2], and again the bilayer was fluidized. It is proposed that a more fluid membrane lipid bilayer, induced by increased unsaturation or non-esterified fatty acids, facilitated optimal interaction at the DAG site since the effect could be demonstrated in a lipid free system using protamine sulfate.

  13. The significance of recruiting underrepresented minorities in medicine: an examination of the need for effective approaches used in admissions by higher education institutions

    PubMed Central

    Figueroa, Obed

    2014-01-01

    The purpose of this paper is to examine the significance of recruiting underrepresented minorities in medicine (URM). This would include African Americans, Hispanics, and Native Americans. The research findings support the belief that URMs, upon graduating, are more likely to become practitioners in underserved communities, thereby becoming a resource that prompts us to find effective ways to help increase their college enrollments statewide. This paper analyzes the recruitment challenges for institutions, followed by a review of creative and effective approaches used by organizations and universities. The results have shown positive outcomes averaging a 50% increase in minority enrollments and retention. In other areas, such as cognitive development, modest gains were achieved in programs that were shorter in duration. The results nevertheless indicated steps in the right direction inspiring further program developments. PMID:25192970

  14. Higher-order electric multipole contributions to retarded non-additive three-body dispersion interaction energies between atoms: equilateral triangle and collinear configurations.

    PubMed

    Salam, A

    2013-12-28

    The theory of molecular quantum electrodynamics (QED) is used to calculate higher electric multipole contributions to the dispersion energy shift between three atoms or molecules arranged in a straight line or in an equilateral triangle configuration. As in two-body potentials, three-body dispersion interactions are viewed in the QED formalism to arise from exchange of virtual photons between coupled pairs of particles. By employing an interaction Hamiltonian that is quadratic in the electric displacement field means that third-order perturbation theory can be used to yield the energy shift for a particular combination of electric multipole polarizable species, with only six time-ordered diagrams needing to be summed over. Specific potentials evaluated include dipole-dipole-quadrupole (DDQ), dipole-quadrupole-quadrupole (DQQ), and dipole-dipole-octupole (DDO) terms. For the geometries of interest, near-zone limiting forms are found to exhibit an R(-11) dependence on separation distance for the DDQ interaction, and an R(-13) behaviour for DQQ and DDO shifts, agreeing with an earlier semi-classical computation. Retardation weakens the potential in each case by R(-1) in the far-zone. It is found that by decomposing the octupole moment into its irreducible components of weights-1 and -3 that the former contribution to the DDO potential may be taken to be a higher-order correction to the leading triple dipole energy shift. PMID:24387355

  15. Higher-order electric multipole contributions to retarded non-additive three-body dispersion interaction energies between atoms: Equilateral triangle and collinear configurations

    SciTech Connect

    Salam, A.

    2013-12-28

    The theory of molecular quantum electrodynamics (QED) is used to calculate higher electric multipole contributions to the dispersion energy shift between three atoms or molecules arranged in a straight line or in an equilateral triangle configuration. As in two-body potentials, three-body dispersion interactions are viewed in the QED formalism to arise from exchange of virtual photons between coupled pairs of particles. By employing an interaction Hamiltonian that is quadratic in the electric displacement field means that third-order perturbation theory can be used to yield the energy shift for a particular combination of electric multipole polarizable species, with only six time-ordered diagrams needing to be summed over. Specific potentials evaluated include dipole-dipole-quadrupole (DDQ), dipole-quadrupole-quadrupole (DQQ), and dipole-dipole-octupole (DDO) terms. For the geometries of interest, near-zone limiting forms are found to exhibit an R{sup −11} dependence on separation distance for the DDQ interaction, and an R{sup −13} behaviour for DQQ and DDO shifts, agreeing with an earlier semi-classical computation. Retardation weakens the potential in each case by R{sup −1} in the far-zone. It is found that by decomposing the octupole moment into its irreducible components of weights-1 and -3 that the former contribution to the DDO potential may be taken to be a higher-order correction to the leading triple dipole energy shift.

  16. Nutrient Addition Leads to a Weaker CO2 Sink and Higher CH4 Emissions through Vegetation-Microclimate Feedbacks at Mer Bleue Bog, Canada

    NASA Astrophysics Data System (ADS)

    Bubier, J. L.; Arnkil, S.; Humphreys, E.; Juutinen, S.; Larmola, T.; Moore, T. R.

    2015-12-01

    Atmospheric nitrogen (N) deposition has led to nutrient enrichment in wetlands globally, affecting plant community composition, carbon (C) cycling, and microbial dynamics. Nutrient-limited boreal bogs are long-term sinks of carbon dioxide (CO2), but sources of methane (CH4), an important greenhouse gas. We fertilized Mer Bleue Bog, a Sphagnum moss and evergreen shrub-dominated ombrotrophic bog near Ottawa, Ontario, for 10-15 years with N as NO3 and NH4 at 5, 10 and 20 times ambient N deposition (0.6-0.8 g N m-2 y-1), with and without phosphorus (P) and potassium (K). Treatments were applied to triplicate plots (3 x 3 m) from May - August 2000-2015 and control plots received distilled water. We measured net ecosystem CO2 exchange (NEE), ecosystem photosynthesis and respiration, and CH4 flux with climate-controlled chambers; leaf-level CO2 exchange and biochemistry; substrate-induced respiration, CH4 production and consumption potentials with laboratory incubations; plant species composition and abundance; and microclimate (peat temperature, moisture, light interception). After 15 years, we have found that NEE has decreased, and CH4 emissions have increased, in the highest nutrient treatments owing to changes in vegetation, microtopography, and peat characteristics. Vegetation changes include a loss of Sphagnum moss and introduction of new deciduous species. Simulated atmospheric N deposition has not benefitted the photosynthetic apparatus of the dominant evergreen shrubs, but resulted in higher foliar respiration, contributing to a weaker ecosystem CO2 sink. Loss of moss has led to wetter near-surface substrate, higher rates of decomposition and CH4 emission, and a shift in microbial communities. Thus, elevated atmospheric deposition of nutrients may endanger C storage in peatlands through a complex suite of feedbacks and interactions among vegetation, microclimate, and microbial communities.

  17. Significantly Higher Peripheral Insulin-Like Growth Factor-1 Levels in Patients With Major Depressive Disorder or Bipolar Disorder Than in Healthy Controls: A Meta-Analysis and Review Under Guideline of PRISMA.

    PubMed

    Tu, Kun-Yu; Wu, Ming-Kung; Chen, Yen-Wen; Lin, Pao-Yen; Wang, Hung-Yu; Wu, Ching-Kuan; Tseng, Ping-Tao

    2016-01-01

    An increasing amount of research has focused on insulin-like growth factor-1 (IGF-1) because of multiple neurotrophic effects, including neurogenesis, remyelination, and synaptogenesis. In addition, IGF-1 can mediate an antidepressant effect in patients with major affective disorder, and its levels in the cerebrospinal fluid have been found to vary with antidepressant treatment. Furthermore, it has been proven to crossover the blood-brain barrier, with a reciprocal feedback loop being the central effect. However, recent studies have reported inconclusive findings about the role of IGF-1 in major affective disorder. The aim of the current study was to conduct a thorough meta-analysis of changes in peripheral IGF-1 levels in patients with major depressive disorder (MDD) or bipolar disorder (BD). We conducted a thorough literature search and compared peripheral IGF-1 levels in patients with MDD or BD and in healthy controls, and investigated clinical variables through meta-regression. Electronic research was conducted through platform of PubMed. We used inclusion criteria as clinical trials discussing comparisons of peripheral IGF-1 protein levels in patients with MDD or BD and those in healthy controls. We analyzed the cases from 9 studies with the random-effect model. The main finding was that peripheral IGF-1 levels in the patients were significantly higher than in the healthy controls (P < 0.001), with a significant inverse association with duration of illness (P = 0.03). In meta-analysis comparing peripheral IGF-1 levels in patients with BD or MDD before and after treatment, there was no significant change in peripheral IGF-1 levels after treatment (P = 0.092). The small numbers of studies and lack of correlation data with growth hormone in current studies are the main limitations of this meta-analysis. Our results indicated that peripheral IGF-1 levels may not be an indicator of disease severity, but may be a disease trait marker or an indicator of

  18. Significantly Higher Peripheral Insulin-Like Growth Factor-1 Levels in Patients With Major Depressive Disorder or Bipolar Disorder Than in Healthy Controls: A Meta-Analysis and Review Under Guideline of PRISMA.

    PubMed

    Tu, Kun-Yu; Wu, Ming-Kung; Chen, Yen-Wen; Lin, Pao-Yen; Wang, Hung-Yu; Wu, Ching-Kuan; Tseng, Ping-Tao

    2016-01-01

    An increasing amount of research has focused on insulin-like growth factor-1 (IGF-1) because of multiple neurotrophic effects, including neurogenesis, remyelination, and synaptogenesis. In addition, IGF-1 can mediate an antidepressant effect in patients with major affective disorder, and its levels in the cerebrospinal fluid have been found to vary with antidepressant treatment. Furthermore, it has been proven to crossover the blood-brain barrier, with a reciprocal feedback loop being the central effect. However, recent studies have reported inconclusive findings about the role of IGF-1 in major affective disorder. The aim of the current study was to conduct a thorough meta-analysis of changes in peripheral IGF-1 levels in patients with major depressive disorder (MDD) or bipolar disorder (BD). We conducted a thorough literature search and compared peripheral IGF-1 levels in patients with MDD or BD and in healthy controls, and investigated clinical variables through meta-regression. Electronic research was conducted through platform of PubMed. We used inclusion criteria as clinical trials discussing comparisons of peripheral IGF-1 protein levels in patients with MDD or BD and those in healthy controls. We analyzed the cases from 9 studies with the random-effect model. The main finding was that peripheral IGF-1 levels in the patients were significantly higher than in the healthy controls (P < 0.001), with a significant inverse association with duration of illness (P = 0.03). In meta-analysis comparing peripheral IGF-1 levels in patients with BD or MDD before and after treatment, there was no significant change in peripheral IGF-1 levels after treatment (P = 0.092). The small numbers of studies and lack of correlation data with growth hormone in current studies are the main limitations of this meta-analysis. Our results indicated that peripheral IGF-1 levels may not be an indicator of disease severity, but may be a disease trait marker or an indicator of

  19. HIF-1α 1772 C/T and 1790 G/A Polymorphisms Are Significantly Associated with Higher Cancer Risk: An Updated Meta-Analysis from 34 Case-Control Studies

    PubMed Central

    Zhang, Chi; Qin, Qin; Liu, Jia; Xu, Li-Ping; Zhao, Lian-Jun; Zhang, Qu; Cai, Jing; Ma, Jian-Xin; Cheng, Hong-Yan; Sun, Xin-Chen

    2013-01-01

    Background HIF-1 activates various genes in cancer progression and metastasis. HIF-1α 1772 C/T and 1790 G/A polymorphisms are reportedly associated with cancer risk; however, the results are inconclusive. Methodology/Principal Findings A meta-analysis of 34 studies that involved 7522 cases and 9847 controls for 1772 C/T and 24 studies that involved 4884 cases and 8154 controls for 1790 G/A was conducted to identify the association of C/T and G/A polymorphisms with cancer risk. Odds ratio (OR) and 95% confidence intervals (95% CI) were used to assess the strength of association. HIF-1α 1772 C/T and 1790 G/A polymorphisms were associated with higher cancer risk in homozygote comparison (1772C/T: TT vs. CC: OR = 2.45, 95% CI: 1.52, 3.96; Pheterogeneity = 0.028; 1790G/A: AA vs. GG: OR=4.74, 95% CI: 1.78, 12.6; Pheterogeneity < 0.01), dominant model (1772C/T: TT/CT vs. CC: OR = 1.27, 95% CI: 1.04, 1.55; Pheterogeneity < 0.01, 1790G/A: AA/GA vs. GG: OR = 1.65, 95% CI: 1.05, 2.60; Pheterogeneity < 0.01), T allele versus C allele (T vs. C: OR = 1.42, 95% CI: 1.18, 1.70; Pheterogeneity < 0.01), and A allele versus G allele (A vs. G: OR = 1.83, 95% CI: 1.13, 2.96; Pheterogeneity < 0.01). On a subgroup analysis, the 1772 C/T polymorphism was significantly linked to higher risks for breast cancer, lung cancer, prostate cancer, and cervical cancer, whereas the 1790 G/A polymorphism was significantly linked to higher risks for lung cancer and prostate cancer. A significantly increased cancer risk was found in both Asians and Caucasians for 1772C/T polymorphism, whereas a significantly increased cancer risk was found in Caucasians in the heterozygote comparison and recessive model for 1790G/A polymorphism. Conclusions HIF-1α 1772 C/T and 1790 G/A polymorphisms are significantly associated with higher cancer risk. PMID:24260383

  20. Food additives

    PubMed Central

    Spencer, Michael

    1974-01-01

    Food additives are discussed from the food technology point of view. The reasons for their use are summarized: (1) to protect food from chemical and microbiological attack; (2) to even out seasonal supplies; (3) to improve their eating quality; (4) to improve their nutritional value. The various types of food additives are considered, e.g. colours, flavours, emulsifiers, bread and flour additives, preservatives, and nutritional additives. The paper concludes with consideration of those circumstances in which the use of additives is (a) justified and (b) unjustified. PMID:4467857

  1. Significantly higher activity of a cytoplasmic hammerhead ribozyme than a corresponding nuclear counterpart: engineered tRNAs with an extended 3′ end can be exported efficiently and specifically to the cytoplasm in mammalian cells

    PubMed Central

    Kuwabara, Tomoko; Warashina, Masaki; Koseki, Shiori; Sano, Masayuki; Ohkawa, Jun; Nakayama, Kazuhisa; Taira, Kazunari

    2001-01-01

    Hammerhead ribozymes were expressed under the control of similar tRNA promoters, localizing transcripts either in the cytoplasm or the nucleus. The tRNAVal-driven ribozyme (tRNA-Rz; tRNA with extra sequences at the 3′ end) that has been used in our ribozyme studies was exported efficiently into the cytoplasm and ribozyme activity was detected only in the cytoplasmic fraction. Both ends of the transported tRNA-Rz were characterized comprehensively and the results confirmed that tRNA-Rz had unprocessed 5′ and 3′ ends. Furthermore, it was also demonstrated that the activity of the exported ribozyme was significantly higher than that of the ribozyme which remained in the nucleus. We suggest that it is possible to engineer tRNA-Rz, which can be exported to the cytoplasm based on an understanding of secondary structures, and then tRNA-driven ribozymes may be co-localized with their target mRNAs in the cytoplasm of mammalian cells. PMID:11433023

  2. Mixtures of 3,4-methylenedioxymethamphetamine (ecstasy) and its major human metabolites act additively to induce significant toxicity to liver cells when combined at low, non-cytotoxic concentrations.

    PubMed

    da Silva, Diana Dias; Silva, Elisabete; Carvalho, Félix; Carmo, Helena

    2014-06-01

    Hepatic injury after 3,4-methylenedioxymethamphetamine (MDMA; ecstasy) intoxications is highly unpredictable and does not seem to correlate with either dosage or frequency of use. The mechanisms involved include the drug metabolic bioactivation and the hyperthermic state of the liver triggered by its thermogenic action and exacerbated by the environmental circumstances of abuse at hot and crowded venues. We became interested in understanding the interaction between ecstasy and its metabolites generated in vivo as users are always exposed to mixtures of parent drug and metabolites. With this purpose, Hep G2 cells were incubated with MDMA and its main human metabolites methylenedioxyamphetamine (MDA), α-methyldopamine (α-MeDA) and N-methyl-α-methyldopamine (N-Me-α-MeDA), individually and in mixture (drugs combined in proportion to their individual EC01 ), at normal (37 °C) and hyperthermic (40.5 °C) conditions. After 48 h, viability was assessed by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. Extensive concentration-response analysis was performed with single drugs and the parameters of the individual non-linear logit fits were used to predict joint effects using the well-founded models of concentration addition (CA) and independent action (IA). Experimental testing revealed that mixture effects on cell viability conformed to CA, for both temperature settings. Additionally, substantial combination effects were attained even when each substance was present at concentrations that individually produced unnoticeable effects. Hyperthermic incubations dramatically increased the toxicity of the tested drug and metabolites, both individually and combined. These outcomes suggest that MDMA metabolism has hazard implications to liver cells even when metabolites are found in low concentrations, as they contribute additively to the overall toxic effect of MDMA.

  3. Phosphazene additives

    DOEpatents

    Harrup, Mason K; Rollins, Harry W

    2013-11-26

    An additive comprising a phosphazene compound that has at least two reactive functional groups and at least one capping functional group bonded to phosphorus atoms of the phosphazene compound. One of the at least two reactive functional groups is configured to react with cellulose and the other of the at least two reactive functional groups is configured to react with a resin, such as an amine resin of a polycarboxylic acid resin. The at least one capping functional group is selected from the group consisting of a short chain ether group, an alkoxy group, or an aryloxy group. Also disclosed are an additive-resin admixture, a method of treating a wood product, and a wood product.

  4. Potlining Additives

    SciTech Connect

    Rudolf Keller

    2004-08-10

    In this project, a concept to improve the performance of aluminum production cells by introducing potlining additives was examined and tested. Boron oxide was added to cathode blocks, and titanium was dissolved in the metal pool; this resulted in the formation of titanium diboride and caused the molten aluminum to wet the carbonaceous cathode surface. Such wetting reportedly leads to operational improvements and extended cell life. In addition, boron oxide suppresses cyanide formation. This final report presents and discusses the results of this project. Substantial economic benefits for the practical implementation of the technology are projected, especially for modern cells with graphitized blocks. For example, with an energy savings of about 5% and an increase in pot life from 1500 to 2500 days, a cost savings of $ 0.023 per pound of aluminum produced is projected for a 200 kA pot.

  5. Reauthorizing the Higher Education Act: Opportunities to Improve Student Success. Additional Submitted Testimony from Lashawn Richburg-Hayes, MDRC, to the Senate Committee on Health, Education, Labor, and Pensions

    ERIC Educational Resources Information Center

    Richburg-Hayes, Lashawn

    2015-01-01

    MDRC is pleased to have this opportunity to provide additional information for the consideration of Chairman Alexander, Ranking Member Murray, and members of the Committee on ways research can be used to improve the academic success of low-income college students. The goal of this additional testimony is to reiterate the second recommendation in…

  6. Higher Education or Higher Skilling?

    ERIC Educational Resources Information Center

    Muller, Steven

    1974-01-01

    Higher education may return to education for a minority, an unlikely course; concentrate on higher skilling, the road we are on today; or restore general education, the most attractive possibility, which can be implemented by restoring basic education in literacy, history, human biology, and language. (JH)

  7. The Mozart Effect: Additional Data.

    PubMed

    Hughes, John R.

    2002-04-01

    After the review of the Mozart effect was published in this journal (Hughes JR. Epilepsy Behav 2001;2:369-417), additional data from the music of Haydn and Liszt have been analyzed that may account for the decrease in seizure activity originally reported during Mozart music. Even with these added data Mozart music continued to score significantly higher than the selections from the other six composers in one of the important characteristics of this music, namely, the repetition of the melody. However Haydn's values were second highest among Mozart, J. S. Bach, Wagner, Beethoven, Chopin, and Liszt.

  8. Higher Education.

    ERIC Educational Resources Information Center

    Hendrickson, Robert M.

    This eighth chapter of "The Yearbook of School Law, 1986" summarizes and analyzes over 330 state and federal court cases litigated in 1985 in which institutions of higher education were involved. Among the topics examined were relationships between postsecondary institutions and various governmental agencies; discrimination in the employment of…

  9. Higher Education.

    ERIC Educational Resources Information Center

    Hendrickson, Robert M.; Gregory, Dennis E.

    Decisions made by federal and state courts during 1983 concerning higher education are reported in this chapter. Issues of employment and the treatment of students underlay the bulk of the litigation. Specific topics addressed in these and other cases included federal authority to enforce regulations against age discrimination and to revoke an…

  10. Higher Education.

    ERIC Educational Resources Information Center

    Hendrickson, Robert M.

    Litigation in 1987 was very brisk with an increase in the number of higher education cases reviewed. Cases discussed in this chapter are organized under four major topics: (1) intergovernmental relations; (2) employees, involving discrimination claims, tenured and nontenured faculty, collective bargaining and denial of employee benefits; (3)…

  11. Higher Education.

    ERIC Educational Resources Information Center

    Hendrickson, Robert M.; Finnegan, Dorothy E.

    The higher education case law in 1988 is extensive. Cases discussed in this chapter are organized under five major topics: (1) intergovernmental relations; (2) employees, involving discrimination claims, tenured and nontenured faculty, collective bargaining, and denial of employee benefits; (3) students, involving admissions, financial aid, First…

  12. Higher Learning.

    ERIC Educational Resources Information Center

    Bok, Derek

    Factors that distinguish the United States higher education system and its performance are considered, with attention to new developments, propsects for change, undergraduate education, and professional schools (especially law, business, and medicine). The way universities change the methods and content of their teaching in response to new…

  13. Phenylethynyl Containing Reactive Additives

    NASA Technical Reports Server (NTRS)

    Connell, John W. (Inventor); Smith, Joseph G., Jr. (Inventor); Hergenrother, Paul M. (Inventor)

    2002-01-01

    Phenylethynyl containing reactive additives were prepared from aromatic diamine, containing phenylethvnvl groups and various ratios of phthalic anhydride and 4-phenylethynviphthalic anhydride in glacial acetic acid to form the imide in one step or in N-methyl-2-pvrrolidinone to form the amide acid intermediate. The reactive additives were mixed in various amounts (10% to 90%) with oligomers containing either terminal or pendent phenylethynyl groups (or both) to reduce the melt viscosity and thereby enhance processability. Upon thermal cure, the additives react and become chemically incorporated into the matrix and effect an increase in crosslink density relative to that of the host resin. This resultant increase in crosslink density has advantageous consequences on the cured resin properties such as higher glass transition temperature and higher modulus as compared to that of the host resin.

  14. CALIFORNIA'S NEEDS FOR ADDITIONAL CENTERS OF PUBLIC HIGHER EDUCATION.

    ERIC Educational Resources Information Center

    RICHARDS, JOHN R.; AND OTHERS

    SINCE 1959, 11 NEW JUNIOR COLLEGES HAVE BEEN ORGANIZED IN THE 21 AREAS RECOMMENDED IN THE MASTER PLAN. ANNEXATIONS AND CONSTRUCTION OR PLANNING OF NEW CAMPUSES HAVE TAKEN PLACE IN ALL THE REMAINING AREAS. AS A RESULT OF THIS GROWTH, PLUS INCREASE IN SIZE OF EXISTING DISTRICTS, OVER 80 PERCENT OF THE HIGH SCHOOL AVERAGE DAILY ATTENDANCE AND OVER 80…

  15. Additive Manufacturing Infrared Inspection

    NASA Technical Reports Server (NTRS)

    Gaddy, Darrell

    2014-01-01

    Additive manufacturing is a rapid prototyping technology that allows parts to be built in a series of thin layers from plastic, ceramics, and metallics. Metallic additive manufacturing is an emerging form of rapid prototyping that allows complex structures to be built using various metallic powders. Significant time and cost savings have also been observed using the metallic additive manufacturing compared with traditional techniques. Development of the metallic additive manufacturing technology has advanced significantly over the last decade, although many of the techniques to inspect parts made from these processes have not advanced significantly or have limitations. Several external geometry inspection techniques exist such as Coordinate Measurement Machines (CMM), Laser Scanners, Structured Light Scanning Systems, or even traditional calipers and gages. All of the aforementioned techniques are limited to external geometry and contours or must use a contact probe to inspect limited internal dimensions. This presentation will document the development of a process for real-time dimensional inspection technique and digital quality record of the additive manufacturing process using Infrared camera imaging and processing techniques.

  16. Statistical or biological significance?

    PubMed

    Saxon, Emma

    2015-01-01

    Oat plants grown at an agricultural research facility produce higher yields in Field 1 than in Field 2, under well fertilised conditions and with similar weather exposure; all oat plants in both fields are healthy and show no sign of disease. In this study, the authors hypothesised that the soil microbial community might be different in each field, and these differences might explain the difference in oat plant growth. They carried out a metagenomic analysis of the 16 s ribosomal 'signature' sequences from bacteria in 50 randomly located soil samples in each field to determine the composition of the bacterial community. The study identified >1000 species, most of which were present in both fields. The authors identified two plant growth-promoting species that were significantly reduced in soil from Field 2 (Student's t-test P < 0.05), and concluded that these species might have contributed to reduced yield. PMID:26541972

  17. The addition of rituximab to a combination of fludarabine, cyclophosphamide, mitoxantrone (FCM) significantly increases the response rate and prolongs survival as compared with FCM alone in patients with relapsed and refractory follicular and mantle cell lymphomas: results of a prospective randomized study of the German Low-Grade Lymphoma Study Group.

    PubMed

    Forstpointner, Roswitha; Dreyling, Martin; Repp, Roland; Hermann, Sandra; Hänel, Annette; Metzner, Bernd; Pott, Christiane; Hartmann, Frank; Rothmann, Frank; Rohrberg, Robert; Böck, Hans-Peter; Wandt, Hannes; Unterhalt, Michael; Hiddemann, Wolfgang

    2004-11-15

    In follicular lymphoma (FL) and mantle cell lymphoma (MCL) the monoclonal antibody rituximab may improve the prognosis when combined with chemotherapy. This was investigated in a prospective randomized study in patients with relapsed disease. A total of 147 patients were randomized to receive 4 courses of chemotherapy with 25 mg/m(2) fludarabine on days 1 to 3, 200 mg/m(2) cyclophosphamide on days 1 to 3, and 8 mg/m(2) mitoxantrone on day 1 (FCM), alone or combined with rituximab (375 mg/m(2); R-FCM). Of 128 evaluable patients, 62 were randomized for FCM and 66 for R-FCM. R-FCM revealed an overall response rate of 79% (33% complete remission [CR], 45% partial remission [PR]) as compared with 58% for FCM alone (13% CR, 45% PR; P = .01), with similar results in a subgroup analysis of FL (94% vs 70%) and MCL (58% vs 46%). In the total group, the R-FCM arm was significantly superior concerning progression-free survival (PFS; P = .0381) and overall survival (OS; P = .0030). In FL PFS was significantly longer in the R-FCM arm (P = .0139) whereas in MCL a significantly longer OS was observed (P = .0042). There were no differences in clinically relevant side effects in both study arms. Hence, the addition of rituximab to FCM chemotherapy significantly improves the outcome of relapsed or refractory FL and MCL.

  18. Significant Tsunami Events

    NASA Astrophysics Data System (ADS)

    Dunbar, P. K.; Furtney, M.; McLean, S. J.; Sweeney, A. D.

    2014-12-01

    Tsunamis have inflicted death and destruction on the coastlines of the world throughout history. The occurrence of tsunamis and the resulting effects have been collected and studied as far back as the second millennium B.C. The knowledge gained from cataloging and examining these events has led to significant changes in our understanding of tsunamis, tsunami sources, and methods to mitigate the effects of tsunamis. The most significant, not surprisingly, are often the most devastating, such as the 2011 Tohoku, Japan earthquake and tsunami. The goal of this poster is to give a brief overview of the occurrence of tsunamis and then focus specifically on several significant tsunamis. There are various criteria to determine the most significant tsunamis: the number of deaths, amount of damage, maximum runup height, had a major impact on tsunami science or policy, etc. As a result, descriptions will include some of the most costly (2011 Tohoku, Japan), the most deadly (2004 Sumatra, 1883 Krakatau), and the highest runup ever observed (1958 Lituya Bay, Alaska). The discovery of the Cascadia subduction zone as the source of the 1700 Japanese "Orphan" tsunami and a future tsunami threat to the U.S. northwest coast, contributed to the decision to form the U.S. National Tsunami Hazard Mitigation Program. The great Lisbon earthquake of 1755 marked the beginning of the modern era of seismology. Knowledge gained from the 1964 Alaska earthquake and tsunami helped confirm the theory of plate tectonics. The 1946 Alaska, 1952 Kuril Islands, 1960 Chile, 1964 Alaska, and the 2004 Banda Aceh, tsunamis all resulted in warning centers or systems being established.The data descriptions on this poster were extracted from NOAA's National Geophysical Data Center (NGDC) global historical tsunami database. Additional information about these tsunamis, as well as water level data can be found by accessing the NGDC website www.ngdc.noaa.gov/hazard/

  19. Addition of Rice Bran Arabinoxylan to Curcumin Therapy May Be of Benefit to Patients With Early-Stage B-Cell Lymphoid Malignancies (Monoclonal Gammopathy of Undetermined Significance, Smoldering Multiple Myeloma, or Stage 0/1 Chronic Lymphocytic Leukemia): A Preliminary Clinical Study.

    PubMed

    Golombick, Terry; Diamond, Terrence H; Manoharan, Arumugam; Ramakrishna, Rajeev

    2016-06-01

    Hypothesis Prior studies on patients with early B-cell lymphoid malignancies suggest that early intervention with curcumin may lead to delay in progressive disease and prolonged survival. These patients are characterized by increased susceptibility to infections. Rice bran arabinoxylan (Ribraxx) has been shown to have immunostimulatory, anti-inflammatory, and proapoptotic effects. We postulated that addition of Ribraxx to curcumin therapy may be of benefit. Study design Monoclonal gammopathy of undetermined significance (MGUS)/smoldering multiple myeloma (SMM) or stage 0/1 chronic lymphocytic leukemia (CLL) patients who had been on oral curcumin therapy for a period of 6 months or more were administered both curcumin (as Curcuforte) and Ribraxx. Methods Ten MGUS/SMM patients and 10 patients with stage 0/1 CLL were administered 6 g of curcumin and 2 g Ribraxx daily. Blood samples were collected at baseline and at 2-month intervals for a period of 6 months, and various markers were monitored. MGUS/SMM patients included full blood count (FBC); paraprotein; free light chains/ratio; C-reactive protein (CRP)and erythrocyte sedimentation rate (ESR); B2 microglobulin and immunological markers. Markers monitored for stage 0/1 CLL were FBC, CRP and ESR, and immunological markers. Results Of 10 MGUS/SMM patients,5 (50%) were neutropenic at baseline, and the Curcuforte/Ribraxx combination therapy showed an increased neutrophil count, varying between 10% and 90% among 8 of the 10 (80%) MGUS/SMM patients. An additional benefit of the combination therapy was the potent effect in reducing the raised ESR in 4 (44%) of the MGUS/SMM patients. Conclusion Addition of Ribraxx to curcumin therapy may be of benefit to patients with early-stage B-cell lymphoid malignancies. PMID:27154182

  20. Higher order Bezier circles

    NASA Technical Reports Server (NTRS)

    Chou, Jin

    1993-01-01

    Rational Bezier and B-spline representations of circles have been heavily publicized. However, all the literature assumes the rational Bezier segments in the homogeneous space are both planar and (equivalent to) quadratic. This creates the illusion that circles can only be achieved by planar and quadratic curves. Circles that are formed by higher order rational Bezier curves which are nonplanar in the homogeneous space are shown. The problem of whether it is possible to represent a complete circle with one Bezier curve is investigated. In addition, some other interesting properties of cubic Bezier arcs are discussed.

  1. Significant association between DRD3 gene body methylation and schizophrenia.

    PubMed

    Dai, Dongjun; Cheng, Jia; Zhou, Kena; Lv, Yuelong; Zhuang, Qidong; Zheng, Rongjiong; Zhang, Kai; Jiang, Danjie; Gao, Shugui; Duan, Shiwei

    2014-12-30

    The current study was the first one to reveal the contribution of DRD3 methylation to the risk of different (SCZ) subtypes. This study comprised a total of 30 paranoid (15 males and 15 females) and 29 undifferentiated (15 males and 14 females) SCZ patients and 26 age- and gender-matched controls. Our results showed a significant association of CpG2 with SCZ. A breakdown analysis by gender showed that CpG2 and CpG3 methylation were significantly higher in male patients than male controls, and that CpG5 methylation was significantly higher in female patients than female controls. A further breakdown analysis by both gender and SCZ subtype showed that CpG2 and CpG3 methylation were significantly higher in male paranoid SCZ and male undifferentiated SCZ than male controls. In contrast, CpG2 and CpG3 methylation were significantly lower in female undifferentiated SCZ than female controls. Additionally, CpG5 methylation was significantly higher in female paranoid SCZ than female controls. In conclusion, our findings supported that DRD3 gene body hypermethylation was significantly associated with the risk of SCZ. Future study is needed to clarify the mechanisms by which DRD3 gene body hypermethylation contributes to the risk of SCZ.

  2. [Food additives and healthiness].

    PubMed

    Heinonen, Marina

    2014-01-01

    Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects.

  3. Asian Americans and Higher Education.

    ERIC Educational Resources Information Center

    Endo, Russell

    Unfortunately the story of Asian Americans and higher education is not one of unqualified success. This paper attempts to overview the historical significance and present the problems of Asian Americans in higher education. The first problem is the lack of oral and writing skills among Asian Americans. Part of this problem is cultural, referring…

  4. Disruptive Technologies in Higher Education

    ERIC Educational Resources Information Center

    Flavin, Michael

    2012-01-01

    This paper analyses the role of "disruptive" innovative technologies in higher education. In this country and elsewhere, Higher Education Institutions (HEIs) have invested significant sums in learning technologies, with Virtual Learning Environments (VLEs) being more or less universal, but these technologies have not been universally adopted and…

  5. Women in Higher Education, 1994.

    ERIC Educational Resources Information Center

    Wenninger, Mary Dee, Ed.

    1994-01-01

    This document consists of the 12 monthly issues of a newsletter on women students, teachers, and administrators in higher education, issued in 1994. Each issue includes feature articles, news on higher education, profiles of significant people in the field, and job announcements. The issues' main article topics are: (1) campuses's changing…

  6. Higher Education Collaboratives for Community Engagement and Improvement

    ERIC Educational Resources Information Center

    Pasque, Penny A., Ed.; Smerek, Ryan E., Ed.; Dwyer, Brighid, Ed.; Bowman, Nick, Ed.; Mallory, Bruce L., Ed.

    2005-01-01

    Individually and collectively, institutions of higher education possess considerable resources--human, fiscal, organizational, and intellectual--which are critical to addressing significant social issues. Additionally, these institutions are physically rooted in their communities. Therefore, investing in the betterment of their immediate…

  7. Developmental Changes in Adolescents' Olfactory Performance and Significance of Olfaction

    PubMed Central

    Klötze, Paula; Gerber, Friederike; Croy, Ilona; Hummel, Thomas

    2016-01-01

    Aim of the current work was to examine developmental changes in adolescents’ olfactory performance and personal significance of olfaction. In the first study olfactory identification abilities of 76 participants (31 males and 45 females aged between 10 and 18 years; M = 13.8, SD = 2.3) was evaluated with the Sniffin Stick identification test, presented in a cued and in an uncued manner. Verbal fluency was additionally examined for control purpose. In the second study 131 participants (46 males and 85 females aged between 10 and 18 years; (M = 14.4, SD = 2.2) filled in the importance of olfaction questionnaire. Odor identification abilities increased significantly with age and were significantly higher in girls as compared to boys. These effects were especially pronounced in the uncued task and partly related to verbal fluency. In line, the personal significance of olfaction increased with age and was generally higher among female compared to male participants. PMID:27332887

  8. Clinical significance of chimerism.

    PubMed

    Abuelo, Dianne

    2009-05-15

    Twins have been previously classified as either monozygotic or dizygotic. In recent years, fascinating, non-traditional mechanisms of twinning have been uncovered. We define chimerism versus mosaicism, touch on chimerism in the animal world, and explain timing of chimerism in humans. In addition, we discuss when to suspect chimerism in patients, and how to proceed with diagnostic evaluation and confirmation.

  9. Access and Costs: Recommendations for Title IV. Hearing on Examining Proposals Authorizing Funds for Title IV Student Aid Programs and Issues Relating to Access to Costs of Postsecondary Education of the Higher Education Act, Including S. 1036, To Revise Section 435 of the Higher Education Act To Allow for the Young Americans Bank and Similar Small, Nonprofit Organizations to Provide Additional Funds for Educational Programming, of the Committee on Labor and Human Resources. United States Senate, One Hundred Fifth Congress, First Session.

    ERIC Educational Resources Information Center

    Congress of the U.S., Washington, DC. Senate Committee on Labor and Human Resources.

    This 10th and final hearing in a series related to the reauthorization of the Higher Education Act, focused on three specific areas: (1) the challenges posed by demographic changes in the college student population--nearly half of all students attend community colleges where the average age of students is 29; (2) the challenges and opportunities…

  10. The significance of research

    NASA Astrophysics Data System (ADS)

    2014-02-01

    When promoting the value of their research or procuring funding, researchers often need to explain the significance of their work to the community -- something that can be just as tricky as the research itself.

  11. Food additives and preschool children.

    PubMed

    Martyn, Danika M; McNulty, Breige A; Nugent, Anne P; Gibney, Michael J

    2013-02-01

    Food additives have been used throughout history to perform specific functions in foods. A comprehensive framework of legislation is in place within Europe to control the use of additives in the food supply and ensure they pose no risk to human health. Further to this, exposure assessments are regularly carried out to monitor population intakes and verify that intakes are not above acceptable levels (acceptable daily intakes). Young children may have a higher dietary exposure to chemicals than adults due to a combination of rapid growth rates and distinct food intake patterns. For this reason, exposure assessments are particularly important in this age group. The paper will review the use of additives and exposure assessment methods and examine factors that affect dietary exposure by young children. One of the most widely investigated unfavourable health effects associated with food additive intake in preschool-aged children are suggested adverse behavioural effects. Research that has examined this relationship has reported a variety of responses, with many noting an increase in hyperactivity as reported by parents but not when assessed using objective examiners. This review has examined the experimental approaches used in such studies and suggests that efforts are needed to standardise objective methods of measuring behaviour in preschool children. Further to this, a more holistic approach to examining food additive intakes by preschool children is advisable, where overall exposure is considered rather than focusing solely on behavioural effects and possibly examining intakes of food additives other than food colours.

  12. Polyimide processing additives

    NASA Technical Reports Server (NTRS)

    Fletcher, James C. (Inventor); Pratt, J. Richard (Inventor); St.clair, Terry L. (Inventor); Stoakley, Diane M. (Inventor); Burks, Harold D. (Inventor)

    1992-01-01

    A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

  13. Polyimide processing additives

    NASA Technical Reports Server (NTRS)

    Pratt, J. Richard (Inventor); St.clair, Terry L. (Inventor); Stoakley, Diane M. (Inventor); Burks, Harold D. (Inventor)

    1993-01-01

    A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of the additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

  14. Significant lexical relationships

    SciTech Connect

    Pedersen, T.; Kayaalp, M.; Bruce, R.

    1996-12-31

    Statistical NLP inevitably deals with a large number of rare events. As a consequence, NLP data often violates the assumptions implicit in traditional statistical procedures such as significance testing. We describe a significance test, an exact conditional test, that is appropriate for NLP data and can be performed using freely available software. We apply this test to the study of lexical relationships and demonstrate that the results obtained using this test are both theoretically more reliable and different from the results obtained using previously applied tests.

  15. Additional Types of Neuropathy

    MedlinePlus

    ... A A Listen En Español Additional Types of Neuropathy Charcot's Joint Charcot's Joint, also called neuropathic arthropathy, ... can stop bone destruction and aid healing. Cranial Neuropathy Cranial neuropathy affects the 12 pairs of nerves ...

  16. Food Additives and Hyperkinesis

    ERIC Educational Resources Information Center

    Wender, Ester H.

    1977-01-01

    The hypothesis that food additives are causally associated with hyperkinesis and learning disabilities in children is reviewed, and available data are summarized. Available from: American Medical Association 535 North Dearborn Street Chicago, Illinois 60610. (JG)

  17. Smog control fuel additives

    SciTech Connect

    Lundby, W.

    1993-06-29

    A method is described of controlling, reducing or eliminating, ozone and related smog resulting from photochemical reactions between ozone and automotive or industrial gases comprising the addition of iodine or compounds of iodine to hydrocarbon-base fuels prior to or during combustion in an amount of about 1 part iodine per 240 to 10,000,000 parts fuel, by weight, to be accomplished by: (a) the addition of these inhibitors during or after the refining or manufacturing process of liquid fuels; (b) the production of these inhibitors for addition into fuel tanks, such as automotive or industrial tanks; or (c) the addition of these inhibitors into combustion chambers of equipment utilizing solid fuels for the purpose of reducing ozone.

  18. Higher Education Exchange, 2012

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2012-01-01

    "Higher Education Exchange" publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic societies. Contributors to this issue of the "Higher Education Exchange" examine whether institutions of higher learning are doing anything to increase the capacity of citizens to shape their future.…

  19. Higher Education Exchange, 2010

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2010-01-01

    "Higher Education Exchange" publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic societies. Contributors to this issue of the "Higher Education Exchange" examine whether institutions of higher learning are doing anything to increase the capacity of citizens to shape their future.…

  20. Higher Education Exchange, 2008

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2008-01-01

    "Higher Education Exchange" publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic societies. Contributors to this issue of the "Higher Education Exchange" examine whether institutions of higher learning are doing anything to increase the capacity of citizens to shape their future.…

  1. Higher Education Exchange, 2014

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2014-01-01

    Research shows that not only does higher education not see the public; when the public, in turn, looks at higher education, it sees mostly malaise, inefficiencies, expense, and unfulfilled promises. Yet, the contributors to this issue of the "Higher Education Exchange" tell of bright spots in higher education where experiments in working…

  2. Higher Education Exchange, 2004

    ERIC Educational Resources Information Center

    Brown, David W., Ed; Witte, Deborah, Ed.

    2004-01-01

    The Higher Education Exchange is part of a movement to strengthen higher education's democratic mission and foster a more democratic culture throughout American society. Working in this tradition, the Higher Education Exchange publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic…

  3. Higher Education Exchange, 2005

    ERIC Educational Resources Information Center

    Brown, David W., Ed; Witte, Deborah, Ed.

    2005-01-01

    The "Higher Education Exchange" is part of a movement to strengthen higher education's democratic mission and foster a more democratic culture throughout American society. Working in this tradition, the "Higher Education Exchange" publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic…

  4. Higher Education Exchange, 2011

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2011-01-01

    "Higher Education Exchange" publishes case studies, analyses, news, and ideas about efforts within higher education to develop more democratic societies. Contributors to this issue of the "Higher Education Exchange" examine whether institutions of higher learning are doing anything to increase the capacity of citizens to shape their future.…

  5. Significance of brown dwarfs

    NASA Technical Reports Server (NTRS)

    Black, D. C.

    1986-01-01

    The significance of brown dwarfs for resolving some major problems in astronomy is discussed. The importance of brown dwarfs for models of star formation by fragmentation of molecular clouds and for obtaining independent measurements of the ages of stars in binary systems is addressed. The relationship of brown dwarfs to planets is considered.

  6. Statistical Significance Testing.

    ERIC Educational Resources Information Center

    McLean, James E., Ed.; Kaufman, Alan S., Ed.

    1998-01-01

    The controversy about the use or misuse of statistical significance testing has become the major methodological issue in educational research. This special issue contains three articles that explore the controversy, three commentaries on these articles, an overall response, and three rejoinders by the first three authors. They are: (1)…

  7. Impact of Including Higher Actinides in Fast Reactor Transmutation Analyses

    SciTech Connect

    B. Forget; M. Asgari; R. Ferrer; S. Bays

    2007-09-01

    Previous fast reactor transmutation studies generally disregarded higher mass minor actinides beyond Cm-246 due to various considerations including deficiencies in nuclear cross-section data. Although omission of these higher mass actinides does not significantly impact the neutronic calculations and fuel cycle performance parameters follow-on neutron dose calculations related to fuel recycling, transportation and handling are significantly impacted. This report shows that including the minor actinides in the equilibrium fast reactor calculations will increase the predicted neutron emission by about 30%. In addition a sensitivity study was initiated by comparing the impact of different cross-section evaluation file for representing these minor actinides.

  8. Tougher Addition Polyimides Containing Siloxane

    NASA Technical Reports Server (NTRS)

    St. Clair, T. L.; Maudgal, S.

    1986-01-01

    Laminates show increased impact resistances and other desirable mechanical properties. Bismaleamic acid extended by reaction of diaminosiloxane with maleic anhydride in 1:1 molar ratio, followed by reaction with half this molar ratio of aromatic dianhydride. Bismaleamic acid also extended by reaction of diaminosiloxane with maleic anhydride in 1:2 molar ratio, followed by reaction with half this molar ratio of aromatic diamine (Michael-addition reaction). Impact resistances improved over those of unmodified bismaleimide, showing significant increase in toughness. Aromatic addition polyimides developed as both matrix and adhesive resins for applications on future aircraft and spacecraft.

  9. Tales of significance.

    PubMed

    Bell, Graham

    2016-01-01

    In this experiment, the authors were interested in testing the effect of a small molecule inhibitor on the ratio of males and females in the offspring of their model Dipteran species. The authors report that in a wild-type population, ~50 % of offspring are male. They then test the effect of treating females with the chemical, which they think might affect the male:female ratio compared with the untreated group. They claim that there is a statistically significant increase in the percentage of males produced and conclude that the drug affects sex ratios. PMID:27338560

  10. Additive-free digital microfluidics.

    PubMed

    Freire, Sergio L S; Tanner, Brendan

    2013-07-16

    Digital microfluidics, a technique for manipulation of droplets, is becoming increasingly important for the development of miniaturized platforms for laboratory processes. Despite the enthusiasm, droplet motion is frequently hindered by the desorption of proteins or other analytes to surfaces. Current approaches to minimize this unwanted surface fouling involve the addition of extra species to the droplet or its surroundings, which might be problematic depending on the droplet content. Here, a new strategy is introduced to move droplets containing cells and other analytes on solid substrates, without extra moieties; in particular, droplets with bovine serum albumin could be moved at a concentration 2000 times higher than previously reported (without additives). This capability is achieved by using a soot-based superamphiphobic surface combined with a new device geometry, which favors droplet rolling. Contrasting with electrowetting, wetting forces are not required for droplet motion.

  11. [Submitting studies without significant results].

    PubMed

    Texier, Gaëtan; Meynard, Jean-Baptiste; Michel, Rémy; Migliani, René; Boutin, Jean-Paul

    2007-03-01

    When a study finds that no exposure factor or therapy is significantly related to a given effect, researchers legitimately wonder if the results should be submitted for publication and to what journal. Clinical trials that report significant associations have a higher probability of publication, a phenomenon known as selective publication. The principal reasons of this selective publication include author self-censorship, peer-reviewing, trials not intended for publication, interpretation of the p value, cost of journal subscriptions, and policies. Subsequent reviews and meta-analyses are biased by the unavailability of nonsignificant results. Suggestions for preventing this risk include university training, trial registries, an international standard randomised controlled trial number (ISRCTN), Cochrane collaboration, and the gray literature. Journals (including electronic journals) interested in studies with nonsignificant results are listed. New technologies are changing the relations between publishers, libraries, authors and readers. PMID:17287106

  12. Multifunctional fuel additives

    SciTech Connect

    Baillargeon, D.J.; Cardis, A.B.; Heck, D.B.

    1991-03-26

    This paper discusses a composition comprising a major amount of a liquid hydrocarbyl fuel and a minor low-temperature flow properties improving amount of an additive product of the reaction of a suitable diol and product of a benzophenone tetracarboxylic dianhydride and a long-chain hydrocarbyl aminoalcohol.

  13. Biobased lubricant additives

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Fully biobased lubricants are those formulated using all biobased ingredients, i.e. biobased base oils and biobased additives. Such formulations provide the maximum environmental, safety, and economic benefits expected from a biobased product. Currently, there are a number of biobased base oils that...

  14. Anthropological significance of phenylketonuria.

    PubMed

    Saugstad, L F

    1975-01-01

    The highest incidence rates of phenylketonuria (PKU) have been observed in Ireland and Scotlant. Parents heterozygous for PKU in Norway differ significantly from the general population in the Rhesus, Kell and PGM systems. The parents investigated showed an excess of Rh negative, Kell plus and PGM type 1 individuals, which makes them similar to the present populations in Ireland and Scotlant. It is postulated that the heterozygotes for PKU in Norway are descended from a completely assimilated sub-population of Celtic origin, who came or were brought here, 1ooo years ago. Bronze objects of Western European (Scottish, Irish) origin, found in Viking graves widely distributed in Norway, have been taken as evidence of Vikings returning with loot (including a number of Celts) from Western Viking settlements. The continuity of residence since the Viking age in most habitable parts of Norway, and what seems to be a nearly complete regional relationship between the sites where Viking graves contain western imported objects and the birthplaces of grandparents of PKUs identified in Norway, lend further support to the hypothesis that the heterozygotes for PKU in Norway are descended from a completely assimilated subpopulation. The remarkable resemblance between Iceland and Ireland, in respect of several genetic markers (including the Rhesus, PGM and Kell systems), is considered to be an expression of a similar proportion of people of Celtic origin in each of the two countries. Their identical, high incidence rates of PKU are regarded as further evidence of this. The significant decline in the incidence of PKU when one passes from Ireland, Scotland and Iceland, to Denmark and on to Norway and Sweden, is therefore explained as being related to a reduction in the proportion of inhabitants of Celtic extraction in the respective populations.

  15. The Higher Education Enterprise.

    ERIC Educational Resources Information Center

    Ottinger, Cecilia A.

    1991-01-01

    Higher education not only contributes to the development of the human resources and intellectual betterment of the nation but is also a major economic enterprise. This research brief reviews and highlights data on the size and growth of higher education and illustrates how higher education institutions are preparing the future labor force. It…

  16. Reflections on "Higher Education"

    ERIC Educational Resources Information Center

    Gilbert, Felix

    1974-01-01

    The elitist, professional, and philosophical elements of higher education are reflected upon with stress on the differences between higher education and higher learning, where education is concerned with giving wider groups a share in a broad image of man, and learning is concerned with increasing specialization. (JH)

  17. Vinyl capped addition polyimides

    NASA Technical Reports Server (NTRS)

    Vannucci, Raymond D. (Inventor); Malarik, Diane C. (Inventor); Delvigs, Peter (Inventor)

    1991-01-01

    Polyimide resins (PMR) are generally useful where high strength and temperature capabilities are required (at temperatures up to about 700 F). Polyimide resins are particularly useful in applications such as jet engine compressor components, for example, blades, vanes, air seals, air splitters, and engine casing parts. Aromatic vinyl capped addition polyimides are obtained by reacting a diamine, an ester of tetracarboxylic acid, and an aromatic vinyl compound. Low void materials with improved oxidative stability when exposed to 700 F air may be fabricated as fiber reinforced high molecular weight capped polyimide composites. The aromatic vinyl capped polyimides are provided with a more aromatic nature and are more thermally stable than highly aliphatic, norbornenyl-type end-capped polyimides employed in PMR resins. The substitution of aromatic vinyl end-caps for norbornenyl end-caps in addition polyimides results in polymers with improved oxidative stability.

  18. Tackifier for addition polyimides

    NASA Technical Reports Server (NTRS)

    Butler, J. M.; St.clair, T. L.

    1980-01-01

    A modification to the addition polyimide, LaRC-160, was prepared to improve tack and drape and increase prepeg out-time. The essentially solventless, high viscosity laminating resin is synthesized from low cost liquid monomers. The modified version takes advantage of a reactive, liquid plasticizer which is used in place of solvent and helps solve a major problem of maintaining good prepeg tack and drape, or the ability of the prepeg to adhere to adjacent plies and conform to a desired shape during the lay up process. This alternate solventless approach allows both longer life of the polymer prepeg and the processing of low void laminates. This approach appears to be applicable to all addition polyimide systems.

  19. The Hesburgh Papers: Higher Values in Higher Education.

    ERIC Educational Resources Information Center

    Hesburgh, Theodore M.

    In this book the president of Notre Dame University responds to the critics who see the teaching of religion and values as a hindrance to institutions of higher learning, suggesting that no university is truly a university unless it is universal and moves every scholar to look to the total universe. The significance of values in education is…

  20. Electrophilic addition of astatine

    SciTech Connect

    Norseev, Yu.V.; Vasaros, L.; Nhan, D.D.; Huan, N.K.

    1988-03-01

    It has been shown for the first time that astatine is capable of undergoing addition reactions to unsaturated hydrocarbons. A new compound of astatine, viz., ethylene astatohydrin, has been obtained, and its retention numbers of squalane, Apiezon, and tricresyl phosphate have been found. The influence of various factors on the formation of ethylene astatohydrin has been studied. It has been concluded on the basis of the results obtained that the univalent cations of astatine in an acidic medium is protonated hypoastatous acid.

  1. Functional Generalized Additive Models.

    PubMed

    McLean, Mathew W; Hooker, Giles; Staicu, Ana-Maria; Scheipl, Fabian; Ruppert, David

    2014-01-01

    We introduce the functional generalized additive model (FGAM), a novel regression model for association studies between a scalar response and a functional predictor. We model the link-transformed mean response as the integral with respect to t of F{X(t), t} where F(·,·) is an unknown regression function and X(t) is a functional covariate. Rather than having an additive model in a finite number of principal components as in Müller and Yao (2008), our model incorporates the functional predictor directly and thus our model can be viewed as the natural functional extension of generalized additive models. We estimate F(·,·) using tensor-product B-splines with roughness penalties. A pointwise quantile transformation of the functional predictor is also considered to ensure each tensor-product B-spline has observed data on its support. The methods are evaluated using simulated data and their predictive performance is compared with other competing scalar-on-function regression alternatives. We illustrate the usefulness of our approach through an application to brain tractography, where X(t) is a signal from diffusion tensor imaging at position, t, along a tract in the brain. In one example, the response is disease-status (case or control) and in a second example, it is the score on a cognitive test. R code for performing the simulations and fitting the FGAM can be found in supplemental materials available online.

  2. Significance of Phi bodies in acute leukaemia.

    PubMed Central

    Cardullo, L de S; Morilla, R; Catovsky, D

    1981-01-01

    Material from 39 patients with acute leukaemia was investigated with the peroxidase cytochemical reaction using 3,3'diaminobenzidine (DAB) and other substrates in order to test their sensitivity in detecting myeloid differentiation. The proportion of positive blasts and of cases with Auer rods in acute myeloid leukaemia (AML) was significantly greater with DAB than with benzidine. In addition, Phi bodies were demonstrated in AML blasts only when DAB was used; Phi bodies were also observed in two out of seven cases of chronic granulocytic leukaemia in "myeloid" blast crisis but were not seen in any case of acute lymphoblastic leukaemia. Phi bodies were more numerous when the reaction was carried out at pH 9.7, and their number was significantly reduced in the presence of 3-amino 1,2,4-triazole. Both findings suggest that the Phi bodies derive from catalase-containing granules (microperoxisomes) and are distinct from Auer rods, which derive from peroxidase-containing (primary) granules. Like Auer rods, Phi bodies appear to be characteristics of immature myeloid cells in leukaemia but are seen with a higher frequency than Auer rods in acute myeloid leukemia. Images p154-a PMID:6262384

  3. Septic tank additive impacts on microbial populations.

    PubMed

    Pradhan, S; Hoover, M T; Clark, G H; Gumpertz, M; Wollum, A G; Cobb, C; Strock, J

    2008-01-01

    Environmental health specialists, other onsite wastewater professionals, scientists, and homeowners have questioned the effectiveness of septic tank additives. This paper describes an independent, third-party, field scale, research study of the effects of three liquid bacterial septic tank additives and a control (no additive) on septic tank microbial populations. Microbial populations were measured quarterly in a field study for 12 months in 48 full-size, functioning septic tanks. Bacterial populations in the 48 septic tanks were statistically analyzed with a mixed linear model. Additive effects were assessed for three septic tank maintenance levels (low, intermediate, and high). Dunnett's t-test for tank bacteria (alpha = .05) indicated that none of the treatments were significantly different, overall, from the control at the statistical level tested. In addition, the additives had no significant effects on septic tank bacterial populations at any of the septic tank maintenance levels. Additional controlled, field-based research iswarranted, however, to address additional additives and experimental conditions.

  4. Fungi producing significant mycotoxins.

    PubMed

    2012-01-01

    Mycotoxins are secondary metabolites of microfungi that are known to cause sickness or death in humans or animals. Although many such toxic metabolites are known, it is generally agreed that only a few are significant in causing disease: aflatoxins, fumonisins, ochratoxin A, deoxynivalenol, zearalenone, and ergot alkaloids. These toxins are produced by just a few species from the common genera Aspergillus, Penicillium, Fusarium, and Claviceps. All Aspergillus and Penicillium species either are commensals, growing in crops without obvious signs of pathogenicity, or invade crops after harvest and produce toxins during drying and storage. In contrast, the important Fusarium and Claviceps species infect crops before harvest. The most important Aspergillus species, occurring in warmer climates, are A. flavus and A. parasiticus, which produce aflatoxins in maize, groundnuts, tree nuts, and, less frequently, other commodities. The main ochratoxin A producers, A. ochraceus and A. carbonarius, commonly occur in grapes, dried vine fruits, wine, and coffee. Penicillium verrucosum also produces ochratoxin A but occurs only in cool temperate climates, where it infects small grains. F. verticillioides is ubiquitous in maize, with an endophytic nature, and produces fumonisins, which are generally more prevalent when crops are under drought stress or suffer excessive insect damage. It has recently been shown that Aspergillus niger also produces fumonisins, and several commodities may be affected. F. graminearum, which is the major producer of deoxynivalenol and zearalenone, is pathogenic on maize, wheat, and barley and produces these toxins whenever it infects these grains before harvest. Also included is a short section on Claviceps purpurea, which produces sclerotia among the seeds in grasses, including wheat, barley, and triticale. The main thrust of the chapter contains information on the identification of these fungi and their morphological characteristics, as well as factors

  5. Reclaiming Our Soul: Democracy and Higher Education.

    ERIC Educational Resources Information Center

    Chickering, Arthur W.

    2003-01-01

    Explores how, as higher education faces new financial realities together with escalating demands for more accountability, a call to reclaim the soul of higher education and with it, the soul of democracy, will require significant institutional and personal transformations. (EV)

  6. Working Memory and Children's Mental Addition.

    ERIC Educational Resources Information Center

    Adams, John W.; Hitch, Graham J.

    1997-01-01

    Two experiments investigated extent to which English- and German-speaking childrens' mental arithmetic was constrained by working memory. Found higher mental addition spans when numbers were visible throughout calculation than when not. Variation in addition span with age and arithmetical operation difficulty approximated to a linear function of…

  7. Disability Discrimination in Higher Education.

    ERIC Educational Resources Information Center

    Weber, Mark C.

    2000-01-01

    Reviews court cases in 1999 related to disability discrimination in higher education focusing on the Americans with Disabilities Act and section 504 of the Rehabilitation Act of 1973. The "Garrett" case regarding Eleventh Amendment immunity is the case most likely to be significant in the development of the law of disability discrimination. (SLD)

  8. Employment Discrimination in Higher Education.

    ERIC Educational Resources Information Center

    Hustoles, Thomas P.; Griffin, Oren R.

    2000-01-01

    Reviews court decisions related to employment discrimination in higher education. The most significant development was a series of cases affirming that Eleventh Amendment immunity from private money damage claims brought pursuant to various federal employment discrimination statutes applied to state colleges and universities. (SLD)

  9. Women in Higher Education, 1997.

    ERIC Educational Resources Information Center

    Wenniger, Mary Dee, Ed.

    1997-01-01

    The 12 issues of this newsletter focus on issues concerned with women students, faculty, and administrators in higher education. Each issue includes feature articles, news items, and profiles of significant people. The issues' main articles address: women in athletics; leadership development for women; the first year in academic administration;…

  10. Additive manufacturing of glass for optical applications

    NASA Astrophysics Data System (ADS)

    Luo, Junjie; Gilbert, Luke J.; Bristow, Douglas A.; Landers, Robert G.; Goldstein, Jonathan T.; Urbas, Augustine M.; Kinzel, Edward C.

    2016-04-01

    Glasses including fused quartz have significant scientific and engineering applications including optics, communications, electronics, and hermetic seals. This paper investigates a filament fed process for Additive Manufacturing (AM) of fused quartz. Additive manufacturing has several potential benefits including increased design freedom, faster prototyping, and lower processing costs for small production volumes. However, current research in AM of glasses is limited and has focused on non-optical applications. Fused quartz is studied here because of its desirability for high-quality optics due to its high transmissivity and thermal stability. Fused quartz also has a higher working temperature than soda lime glass which poses a challenge for AM. In this work, fused quartz filaments are fed into a CO2 laser generated melt pool, smoothly depositing material onto the work piece. Single tracks are printed to explore the effects that different process parameters have on the morphology of printed fused quartz. A spectrometer is used to measure the thermal radiation incandescently emitted from the melt pool. Thin-walls are printed to study the effects of layer-to-layer height. Finally, a 3D fused quartz cube is printed using the newly acquired layer height and polished on each surface. The transmittance and index homogeneity of the polished cube are both measured. These results show that the filament fed process has the potential to print fused quartz with optical transparency and of index of refraction uniformity approaching bulk processed glass.

  11. Performance Boosting Additive

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Mainstream Engineering Corporation was awarded Phase I and Phase II contracts from Goddard Space Flight Center's Small Business Innovation Research (SBIR) program in early 1990. With support from the SBIR program, Mainstream Engineering Corporation has developed a unique low cost additive, QwikBoost (TM), that increases the performance of air conditioners, heat pumps, refrigerators, and freezers. Because of the energy and environmental benefits of QwikBoost, Mainstream received the Tibbetts Award at a White House Ceremony on October 16, 1997. QwikBoost was introduced at the 1998 International Air Conditioning, Heating, and Refrigeration Exposition. QwikBoost is packaged in a handy 3-ounce can (pressurized with R-134a) and will be available for automotive air conditioning systems in summer 1998.

  12. Sewage sludge additive

    NASA Technical Reports Server (NTRS)

    Kalvinskas, J. J.; Mueller, W. A.; Ingham, J. D. (Inventor)

    1980-01-01

    The additive is for a raw sewage treatment process of the type where settling tanks are used for the purpose of permitting the suspended matter in the raw sewage to be settled as well as to permit adsorption of the dissolved contaminants in the water of the sewage. The sludge, which settles down to the bottom of the settling tank is extracted, pyrolyzed and activated to form activated carbon and ash which is mixed with the sewage prior to its introduction into the settling tank. The sludge does not provide all of the activated carbon and ash required for adequate treatment of the raw sewage. It is necessary to add carbon to the process and instead of expensive commercial carbon, coal is used to provide the carbon supplement.

  13. Perspectives on Additive Manufacturing

    NASA Astrophysics Data System (ADS)

    Bourell, David L.

    2016-07-01

    Additive manufacturing (AM) has skyrocketed in visibility commercially and in the public sector. This article describes the development of this field from early layered manufacturing approaches of photosculpture, topography, and material deposition. Certain precursors to modern AM processes are also briefly described. The growth of the field over the last 30 years is presented. Included is the standard delineation of AM technologies into seven broad categories. The economics of AM part generation is considered, and the impacts of the economics on application sectors are described. On the basis of current trends, the future outlook will include a convergence of AM fabricators, mass-produced AM fabricators, enabling of topology optimization designs, and specialization in the AM legal arena. Long-term developments with huge impact are organ printing and volume-based printing.

  14. Sarks as additional fermions

    NASA Astrophysics Data System (ADS)

    Agrawal, Jyoti; Frampton, Paul H.; Jack Ng, Y.; Nishino, Hitoshi; Yasuda, Osamu

    1991-03-01

    An extension of the standard model is proposed. The gauge group is SU(2) X ⊗ SU(3) C ⊗ SU(2) S ⊗ U(1) Q, where all gauge symmetries are unbroken. The colour and electric charge are combined with SU(2) S which becomes strongly coupled at approximately 500 GeV and binds preons to form fermionic and vector bound states. The usual quarks and leptons are singlets under SU(2) X but additional fermions, called sarks. transform under it and the electroweak group. The present model explains why no more than three light quark-lepton families can exist. Neutral sark baryons, called narks, are candidates for the cosmological dark matter having the characteristics designed for WIMPS. Further phenomenological implications of sarks are analyzed i including electron-positron annihilation. Z 0 decay, flavor-changing neutral currents. baryon-number non-conservation, sarkonium and the neutron electric dipole moment.

  15. Pathological Significance of Mitochondrial Glycation

    PubMed Central

    Pun, Pamela Boon Li; Murphy, Michael P.

    2012-01-01

    Glycation, the nonenzymatic glycosylation of biomolecules, is commonly observed in diabetes and ageing. Reactive dicarbonyl species such as methylglyoxal and glyoxal are thought to be major physiological precursors of glycation. Because these dicarbonyls tend to be formed intracellularly, the levels of advanced glycation end products on cellular proteins are higher than on extracellular ones. The formation of glycation adducts within cells can have severe functional consequences such as inhibition of protein activity and promotion of DNA mutations. Although several lines of evidence suggest that there are specific mitochondrial targets of glycation, and mitochondrial dysfunction itself has been implicated in disease and ageing, it is unclear if glycation of biomolecules specifically within mitochondria induces dysfunction and contributes to disease pathology. We discuss here the possibility that mitochondrial glycation contributes to disease, focussing on diabetes, ageing, cancer, and neurodegeneration, and highlight the current limitations in our understanding of the pathological significance of mitochondrial glycation. PMID:22778743

  16. Higher Education in Virginia.

    ERIC Educational Resources Information Center

    Virginia State Council of Higher Education, Richmond.

    For the past 7 years, the State Council of Higher Education has published a report of selected characteristics and degree programs for Virginia's state-supported colleges and universities. By combining data from independent institutions with information collected from the state-supported colleges, a more comprehensive picture of higher education…

  17. Minorities in Higher Education.

    ERIC Educational Resources Information Center

    Justiz, Manuel J., Ed.; And Others

    This book presents 19 papers on efforts to increase the participation of members of minority groups in higher education. The papers are: (1) "Demographic Trends and the Challenges to American Higher Education" (Manuel Justiz); (2) "Three Realities: Minority Life in the United States--The Struggle for Economic Equity (adapted by Don M. Blandin);…

  18. Hypermedia and Higher Education.

    ERIC Educational Resources Information Center

    Lemke, Jay L.

    1993-01-01

    Discusses changes in higher education that are resulting from the use of hypermedia. Topics addressed include the structure of traditional texts; a distributed model for academic communication; independent learning as a model for higher education; skills for hypermedia literacy; database searching; information retrieval; authoring skills; design…

  19. Reinventing Higher Education

    ERIC Educational Resources Information Center

    Hayes, Dianne

    2012-01-01

    Higher education institutions are in the battle of a lifetime as they are coping with political and economic uncertainties, threats to federal aid, declining state support, higher tuition rates and increased competition from for-profit institutions. Amid all these challenges, these institutions are pressed to keep up with technological demands,…

  20. Higher Education Exchange

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2009-01-01

    This volume begins with an essay by Noelle McAfee, a contributor who is familiar to readers of Higher Education Exchange (HEX). She reiterates Mathews' argument regarding the disconnect between higher education's sense of engagement and the public's sense of engagement, and suggests a way around the epistemological conundrum of "knowledge produced…

  1. Higher Education Exchange, 2009

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2009-01-01

    This volume begins with an essay by Noelle McAfee, a contributor who is familiar to readers of Higher Education Exchange (HEX). She reiterates Kettering's president David Mathews' argument regarding the disconnect between higher education's sense of engagement and the public's sense of engagement, and suggests a way around the epistemological…

  2. PHOENIX. Higher Wage Careers.

    ERIC Educational Resources Information Center

    Bismarck State Coll., ND.

    This document outlines the curriculum plan for the one-semester vocational-technical training component of PHOENIX: A Model Program for Higher-Wage Potential Careers offered by Bismarck State College (North Dakota) which prepares and/or retrains individuals for higher-wage technical careers. The comprehensive model for the program is organized…

  3. Higher Education Exchange 2006

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2006-01-01

    Contributors to this issue of the Higher Education Exchange debate the issues around knowledge production, discuss the acquisition of deliberative skills for democracy, and examine how higher education prepares, or does not prepare, students for citizenship roles. Articles include: (1) "Foreword" (Deborah Witte); (2) "Knowledge, Judgment and…

  4. Reimagining Christian Higher Education

    ERIC Educational Resources Information Center

    Hulme, E. Eileen; Groom, David E., Jr.; Heltzel, Joseph M.

    2016-01-01

    The challenges facing higher education continue to mount. The shifting of the U.S. ethnic and racial demographics, the proliferation of advanced digital technologies and data, and the move from traditional degrees to continuous learning platforms have created an unstable environment to which Christian higher education must adapt in order to remain…

  5. Gender and Higher Education

    ERIC Educational Resources Information Center

    Bank, Barbara J., Ed.

    2011-01-01

    This comprehensive, encyclopedic review explores gender and its impact on American higher education across historical and cultural contexts. Challenging recent claims that gender inequities in U.S. higher education no longer exist, the contributors--leading experts in the field--reveal the many ways in which gender is embedded in the educational…

  6. Interactive effects of nutrient additions and predation on infaunal communities

    USGS Publications Warehouse

    Posey, M.H.; Alphin, T.D.; Cahoon, L.; Lindquist, D.; Becker, M.E.

    1999-01-01

    Nutrient additions represent an important anthropogenic stress on coastal ecosystems. At moderate levels, increased nutrients may lead to increased primary production and, possibly, to increased biomass of consumers although complex trophic interactions may modify or mask these effects. We examined the influence of nutrient additions and interactive effects of trophic interactions (predation) on benthic infaunal composition and abundances through small-scale field experiments in 2 estuaries that differed in ambient nutrient conditions. A blocked experimental design was used that allowed an assessment of direct nutrient effects in the presence and absence of predation by epibenthic predators as well as an assessment of the independent effects of predation. Benthic microalgal production increased with experimental nutrient additions and was greater when infaunal abundances were lower, but there were no significant interactions between these factors. Increased abundances of one infaunal taxa, Laeonereis culveri, as well as the grazer feeding guild were observed with nutrient additions and a number of taxa exhibited higher abundances with predator exclusion. In contrast to results from freshwater systems there were no significant interactive effects between nutrient additions and predator exclusion as was predicted. The infaunal responses observed here emphasize the importance of both bottom-up (nutrient addition and primary producer driven) and top-down (predation) controls in structuring benthic communities. These processes may work at different spatial and temporal scales, and affect different taxa, making observation of potential interactive effects difficult.

  7. Individualized additional instruction for calculus

    NASA Astrophysics Data System (ADS)

    Takata, Ken

    2010-10-01

    College students enrolling in the calculus sequence have a wide variance in their preparation and abilities, yet they are usually taught from the same lecture. We describe another pedagogical model of Individualized Additional Instruction (IAI) that assesses each student frequently and prescribes further instruction and homework based on the student's performance. Our study compares two calculus classes, one taught with mandatory remedial IAI and the other without. The class with mandatory remedial IAI did significantly better on comprehensive multiple-choice exams, participated more frequently in classroom discussion and showed greater interest in theorem-proving and other advanced topics.

  8. Additive lattice kirigami

    PubMed Central

    Castle, Toen; Sussman, Daniel M.; Tanis, Michael; Kamien, Randall D.

    2016-01-01

    Kirigami uses bending, folding, cutting, and pasting to create complex three-dimensional (3D) structures from a flat sheet. In the case of lattice kirigami, this cutting and rejoining introduces defects into an underlying 2D lattice in the form of points of nonzero Gaussian curvature. A set of simple rules was previously used to generate a wide variety of stepped structures; we now pare back these rules to their minimum. This allows us to describe a set of techniques that unify a wide variety of cut-and-paste actions under the rubric of lattice kirigami, including adding new material and rejoining material across arbitrary cuts in the sheet. We also explore the use of more complex lattices and the different structures that consequently arise. Regardless of the choice of lattice, creating complex structures may require multiple overlapping kirigami cuts, where subsequent cuts are not performed on a locally flat lattice. Our additive kirigami method describes such cuts, providing a simple methodology and a set of techniques to build a huge variety of complex 3D shapes. PMID:27679822

  9. Additive lattice kirigami

    PubMed Central

    Castle, Toen; Sussman, Daniel M.; Tanis, Michael; Kamien, Randall D.

    2016-01-01

    Kirigami uses bending, folding, cutting, and pasting to create complex three-dimensional (3D) structures from a flat sheet. In the case of lattice kirigami, this cutting and rejoining introduces defects into an underlying 2D lattice in the form of points of nonzero Gaussian curvature. A set of simple rules was previously used to generate a wide variety of stepped structures; we now pare back these rules to their minimum. This allows us to describe a set of techniques that unify a wide variety of cut-and-paste actions under the rubric of lattice kirigami, including adding new material and rejoining material across arbitrary cuts in the sheet. We also explore the use of more complex lattices and the different structures that consequently arise. Regardless of the choice of lattice, creating complex structures may require multiple overlapping kirigami cuts, where subsequent cuts are not performed on a locally flat lattice. Our additive kirigami method describes such cuts, providing a simple methodology and a set of techniques to build a huge variety of complex 3D shapes.

  10. Higher education and civic engagement.

    PubMed

    Egerton, Muriel

    2002-12-01

    This paper focuses on the relationship between social engagement, particularly civic engagement, and education. It is well known that more highly educated people are more likely to engage in voluntary work in formalized settings. It has been difficult to disentangle the effect of higher education from that of family origin and occupational socialization. This paper examines the effects of tertiary education on the social and civic engagement of young people, using the British Household Panel Study. The social and civic activity of young people is observed in their late teens, before entering the labour market or tertiary education, and compared with that of the same young people in their early 20s, after completing tertiary education courses or gaining labour market experience. It was found that the social and civic engagement of young people who would enter higher education was higher in their late teens than that of their peers who did not enter. However, higher education had a small additional effect on civic engagement, for both young and mature students. The children of professionals were the social grouping most likely to be involved in civic activities. The relationship of higher education, professional occupations and family socialization is discussed.

  11. On higher structures

    NASA Astrophysics Data System (ADS)

    Baas, Nils A.

    2016-08-01

    In this paper, we discuss various philosophical aspects of the hyperstructure concept extending networks and higher categories. By this discussion, we hope to pave the way for applications and further developments of the mathematical theory of hyperstructures.

  12. Forecasting Higher Education's Future.

    ERIC Educational Resources Information Center

    Boyken, Don; Buck, Tina S.; Kollie, Ellen; Przyborowski, Danielle; Rondinelli, Joseph A.; Hunter, Jeff; Hanna, Jeff

    2003-01-01

    Offers predictions on trends in higher education to accommodate changing needs, lower budgets, and increased enrollment. They involve campus construction, security, administration, technology, interior design, athletics, and transportation. (EV)

  13. International Higher Education Bibliography.

    ERIC Educational Resources Information Center

    Lulat, Y. G-M.

    1988-01-01

    One in a series of bibliographies of articles in international higher education journals lists items on a variety of administrative, financial, faculty, student, curricular, and related issues. Articles on specific geographic regions are categorized separately. (MSE)

  14. [Effects of nitrogen addition on red soil microbes in the Cinnamomum camphora plantation].

    PubMed

    Yu, Pei-Yi; Zhu, Fan; Su, Shao-Feng; Wang, Zhi-Yong; Yan, Wen-De

    2013-08-01

    In order to investigate the effects of nitrogen addition on the red soil microbial communities in Cinnamomum camphora plantation, three treatments of nitrogen addition were designated as control (N0: 0 g x m(-2)), low nitrogen (N1: 5 g x m(-2)) and high nitrogen (N2 :15 g x m(-2)). Soil microbial numbers, microbial biomass carbon (C), biomass N and microbial community functional diversity were analyzed using the methods of plate counting, chloroform fumigation and BIOLOG system, respectively. The results showed that the numbers of bacteria in N1 and N2 were significantly higher than the control 1 month after nitrogen addition, but significantly lower than the control 13 months after nitrogen addition, and the number of fungi and actinomycetes were not significantly changed after nitrogen addition. The soil microbial biomass C, N increased with the increase of nitrogen at 1 month, but the soil microbial biomass C increased significantly 13 months after nitrogen addition when compared with 1 month after nitrogen addition. The soil microbial biomass N was lower 13 months after nitrogen addition when compared with 1 month after nitrogen addition, but the difference was not significant (P > 0.05). The variation of the carbon utilization efficiency of soil microbial communities was resulted from the nitrogen addition. The indices of Shannon index, Simpson index and McIntosh index were calculated to show the differences in nitrogen treatments and in times, which turned out to be insignificant.

  15. The glycemic index: physiological significance.

    PubMed

    Esfahani, Amin; Wong, Julia M W; Mirrahimi, Arash; Srichaikul, Korbua; Jenkins, David J A; Kendall, Cyril W C

    2009-08-01

    The glycemic index (GI) is a physiological assessment of a food's carbohydrate content through its effect on postprandial blood glucose concentrations. Evidence from trials and observational studies suggests that this physiological classification may have relevance to those chronic Western diseases associated with overconsumption and inactivity leading to central obesity and insulin resistance. The glycemic index classification of foods has been used as a tool to assess potential prevention and treatment strategies for diseases where glycemic control is of importance, such as diabetes. Low GI diets have also been reported to improve the serum lipid profile, reduce C-reactive protein (CRP) concentrations, and aid in weight control. In cross-sectional studies, low GI or glycemic load diets (mean GI multiplied by total carbohydrate) have been associated with higher levels of high-density lipoprotein cholesterol (HDL-C), with reduced CRP concentrations, and, in cohort studies, with decreased risk of developing diabetes and cardiovascular disease. In addition, some case-control and cohort studies have found positive associations between dietary GI and risk of various cancers, including those of the colon, breast, and prostate. Although inconsistencies in the current findings still need to be resolved, sufficient positive evidence, especially with respect to renewed interest in postprandial events, suggests that the glycemic index may have a role to play in the treatment and prevention of chronic diseases.

  16. India's Higher Education Challenges

    ERIC Educational Resources Information Center

    Altbach, Philip G.

    2014-01-01

    India, with the world's second largest higher education system and a rapidly growing economy as one of the BRIC nations, faces significant challenges in building both capacity and excellence in higher education. India's higher education system is characterized by "islands of excellence in a sea of mediocrity." The mainstream…

  17. The Risks of Privatisation of Higher Education

    ERIC Educational Resources Information Center

    Camilleri, Anthony F.

    2008-01-01

    The presentation looks at the latest statistics on participation in Higher Education, to question whether privatisation of systems has significant effects on participation, affordability and equity of Higher Education. It further looks into questions of autonomy and governance of Higher Education systems in private and public systems, and finally…

  18. MAGNETOMETRY, SELF-POTENTIAL, AND SEISMIC - ADDITIONAL GEOPHYSICAL METHODS HAVING POTENTIALLY SIGNIFICANT FUTURE UTILIZATION IN AGRICULTURE

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Geophysical methods can provide important information in agricultural settings, and the use of these techniques are becoming more and more widespread. Magnetrometry, self-potential, and seismic are three geophysical methods, all of which have the potential for substantial future use in agriculture, ...

  19. Higher dimensional nonlinear massive gravity

    NASA Astrophysics Data System (ADS)

    Do, Tuan Q.

    2016-05-01

    Inspired by a recent ghost-free nonlinear massive gravity in four-dimensional spacetime, we study its higher dimensional scenarios. As a result, we are able to show the constantlike behavior of massive graviton terms for some well-known metrics such as the Friedmann-Lemaitre-Robertson-Walker, Bianchi type I, and Schwarzschild-Tangherlini (anti-) de Sitter metrics in a specific five-dimensional nonlinear massive gravity under an assumption that its fiducial metrics are compatible with physical ones. In addition, some simple cosmological solutions of the five-dimensional massive gravity are figured out consistently.

  20. Comparative Higher Education.

    ERIC Educational Resources Information Center

    Altbach, Philip G.

    The comparative higher education course offered at the State University of New York at Buffalo is briefly described, and a course schedule is presented, including required and recommended readings for each topic. The course is intended to provide a broad cross-cultural perspective and considers the growth and development of universities in Europe,…

  1. Valuing Higher Education

    ERIC Educational Resources Information Center

    Pillay, Gerald J.

    2009-01-01

    The question of the value of higher education is today set in the context of an unprecedented banking and financial crisis. In this context of fundamental change and financial realignment, it is important that we as members of the university remake our case for why the university deserves to be considered alongside all those other worthy causes…

  2. Higher Education Exchange, 2003.

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    This annual collection focuses on the obligation of higher education to democracy. Scholars from a variety if disciplines explore this question and related issues, such as the civic mission of the university, what it means to be an "engaged" university, and how a university can itself by a "good citizen." Following a foreword by Deborah Witte, the…

  3. Higher Education's Strange Paradox.

    ERIC Educational Resources Information Center

    Howe, Harold, II

    The university which has had the temerity to change the world has not had the nerve to change itself to live in that world. The result is that the university's grading system, curriculum, teaching methods, and philosophies are in conflict with the world beyond the campus gates, and higher education does not meet the intellectual and social needs…

  4. European Higher Education Society

    ERIC Educational Resources Information Center

    Marcal-Grilo, Eduardo

    2003-01-01

    In his paper, the author--an academic and former Minister of Education for Portugal--traces the origins of the Bologna Declaration of 1999 and its follow-up studies leading to the Prague Conference of Higher Education Ministers in May 2001. He summarises the outcomes of the Prague Conference, and draws conclusions on the crucial role of…

  5. California's Future: Higher Education

    ERIC Educational Resources Information Center

    Johnson, Hans

    2015-01-01

    California's higher education system is not keeping up with the changing economy. Projections suggest that the state's economy will continue to need more highly educated workers. In 2025, if current trends persist, 41 percent of jobs will require at least a bachelor's degree and 36 percent will require some college education short of a bachelor's…

  6. Higher Education Interpreting.

    ERIC Educational Resources Information Center

    Woll, Bencie; Porcari li Destri, Giulia

    This paper discusses issues related to the training and provision of interpreters for deaf students at institutions of higher education in the United Kingdom. Background information provided notes the increasing numbers of deaf and partially hearing students, the existence of funding to pay for interpreters, and trends in the availability of…

  7. Understanding Higher Education Costs

    ERIC Educational Resources Information Center

    Middaugh, Michael F.

    2005-01-01

    Public discussion of higher education costs frequently confuses price with expenditure. This article examines factors associated with increases in the sticker price of a college education and the expenditures incurred by institutions in delivering that education. The discussion suggests that while growth in college tuition is real, access to…

  8. Urban Higher Education Consortia.

    ERIC Educational Resources Information Center

    Paltridge, James Gilbert

    This is a descriptive and evaluative study of 8 consortia formed by urban institutions of higher education confronted with common problems of minority student recruitment, training of teachers for inner-city schools, and the need for academic expertise to help solve their economic and social problems. Findings show that consortia weaknesses stem…

  9. Higher Level Thinking Abilities.

    ERIC Educational Resources Information Center

    Mills, Barbara, Ed.

    This report describes two systems designed to improve teaching competencies and to develop higher level thinking abilities, and presents the evaluation design, statistical results, and a brief history of the major events which occurred during development. The McCollum-Davis Model is designed to develop understanding of and skill in relating a…

  10. Workstations in Higher Education.

    ERIC Educational Resources Information Center

    Weissman, Ronald F. E.; And Others

    1988-01-01

    Five articles discuss various aspects of workstations and their applications in higher education. Highlights include microcomputers and workstations; UNIX operating system; campus-wide networks; software; Project SOCRATES and the interdisciplinary aspect of engineering; mechanical system design and simulation; and the Creation Station, a…

  11. Higher-order Multiples.

    PubMed

    Stone, Joanne; Kohari, Katherine S

    2015-09-01

    Higher-order multiple gestations have increased since the advent of advanced reproductive technologies. These pregnancies present unique risks to both mothers and fetuses. It is imperative that early diagnosis of chronicity be determined and that proper counseling is performed, so patients understand the risks, evaluation, and management needed.

  12. Higher Education in Scotland.

    ERIC Educational Resources Information Center

    Neave, Guy; Cowper, Henry

    1979-01-01

    Analyzes higher education in Scotland in terms of its history and administrative structure and in light of the myths and beliefs about the traditional Scottish university. Differences from English universities are stressed. Journal available from Editor, Gabriel Fragniere, Institute of Education, 60 rue de la Concorde, B-1050, Brussels, Belgium.…

  13. Black at Higher Education

    ERIC Educational Resources Information Center

    Kadi-Hanifi, Karima

    2013-01-01

    This is an exploratory paper, drawing on the author's experiences as well as those of three other black lecturers in Higher Education (HE). Three interviews were carried out, asking the same five questions around themes of concern to the author. These are about the learning and teaching approaches used by these lecturers; their experiences of…

  14. Women in Higher Education.

    ERIC Educational Resources Information Center

    Pifer, Alan

    Women have traditionally been discriminated against in higher education in both the attainment of degrees and in employment after earning degrees. It has been felt that women are not as capable, reliable, or effective as men in administrative and classroom situations. Statistics show that even at the present time women are underemployed and…

  15. Marketing in Higher Education.

    ERIC Educational Resources Information Center

    Hockenberger, Susan J.

    Educational institutions must seek new approaches to institutional planning because of such factors as shrinking traditional college age populations, eroding grants, governmental and judicial incursion, the tightening economic belt, and concern over the relevance of education to modern day needs. The concept of marketing higher education is…

  16. Higher Education Exchange.

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    This collection of 10 articles and stories highlights ongoing experiments in colleges and universities which address the relationship of higher education institutions and citizenship responsibility. Following a foreword by Deborah White, articles are: "The Civic Roots of Academic Social Science Scholarship in American" (R. Claire Snyder), which…

  17. Entrepreneurship and Higher Education

    ERIC Educational Resources Information Center

    Potter, Jonathan, Ed.

    2008-01-01

    Stimulating innovative and growth-oriented entrepreneurship is a key economic and societal challenge to which universities and colleges have much to contribute. This book examines the role that higher education institutions are currently playing through teaching entrepreneurship and transferring knowledge and innovation to enterprises and…

  18. Shell Higher Olefins Process.

    ERIC Educational Resources Information Center

    Lutz, E. F.

    1986-01-01

    Shows how olefin isomerization and the exotic olefin metathesis reaction can be harnessed in industrial processes. Indicates that the Shell Higher Olefins Process makes use of organometallic catalysts to manufacture alpha-olefins and internal carbon-11 through carbon-14 alkenes in a flexible fashion that can be adjusted to market needs. (JN)

  19. Unraveling Higher Education's Costs.

    ERIC Educational Resources Information Center

    Gordon, Gus; Charles, Maria

    1998-01-01

    The activity-based costing (ABC) method of analyzing institutional costs in higher education involves four procedures: determining the various discrete activities of the organization; calculating the cost of each; determining the cost drivers; tracing cost to the cost objective or consumer of each activity. Few American institutions have used the…

  20. Free Higher Education

    ERIC Educational Resources Information Center

    Reed, Jr., Adolph; Szymanski, Sharon

    2004-01-01

    The crisis of affordability in higher education is intensifying. Illustrations of its resonance abound: from the frequent news articles describing and amplifying the crisis and its sources to legislators' and candidates' proposed responses. Republicans' responses tend to be mainly punitive toward institutions; Democrats' proposals are more…

  1. Contracting and Higher Education.

    ERIC Educational Resources Information Center

    Ferris, James M.

    1991-01-01

    The potential gains in efficiency of three types of contracts in college administration are contrasted. Contract types include explicit contracts in the budgeting process between the state and higher education institutions; institutional contracting for inputs; and interinstitutional contracting. The tradeoff between production cost savings and…

  2. Women in Higher Education.

    ERIC Educational Resources Information Center

    O'Donnell, Sheryl, Ed.; Shaver, Barbara, Ed.

    1981-01-01

    Articles on women's studies and females in higher education are presented in this publication. A University of North Dakota project that sought to promote the integration of new research and scholarship results into the curriculum is described in "Women's Equity Committee Offers a Model Project," (Leola Furman, Robert Young). Historical…

  3. Developing Higher Level Thinking

    ERIC Educational Resources Information Center

    Limbach, Barbara; Waugh, Wendy

    2010-01-01

    This paper identifies an interdisciplinary, five-step process, built upon existing theory and best practices in cognitive development, effective learning environments, and outcomes-based assessment. The "Process for the Development of Higher Level Thinking Skills" provides teachers with an easy to implement method of moving toward a more…

  4. Leadership in Higher Education

    ERIC Educational Resources Information Center

    Amey, Marilyn J.

    2006-01-01

    At a time when seasoned higher-education leaders are retiring and the challenges facing prospective administrators seem daunting, how do those in positions of authority or aspiring to those roles construct a meaningful and manageable identity as leaders? Where do they look for support and inspiration? How do they learn to lead? The author…

  5. Liberty and Higher Education.

    ERIC Educational Resources Information Center

    Thompson, Dennis F.

    1989-01-01

    John Stuart Mill's principle of liberty is discussed with the view that it needs to be revised to guide moral judgments in higher education. Three key elements need to be modified: the action that is constrained; the constraint on the action; and the agent whose action is constrained. (MLW)

  6. Creativity in Higher Education

    ERIC Educational Resources Information Center

    Gaspar, Drazena; Mabic, Mirela

    2015-01-01

    The paper presents results of research related to perception of creativity in higher education made by the authors at the University of Mostar from Bosnia and Herzegovina. This research was based on a survey conducted among teachers and students at the University. The authors developed two types of questionnaires, one for teachers and the other…

  7. Marketing in Higher Education.

    ERIC Educational Resources Information Center

    Dalili, Farid

    The use of marketing activities by educational institutions and the transfer of marketing activities from business to higher education are considered. Market analysis helps colleges and universities determine what programs, scheduling, or services are strong and to which student market the institution should appeal. It is suggested that the…

  8. Curriculum in Higher Education.

    ERIC Educational Resources Information Center

    Rothman, A. I., Ed.

    1981-01-01

    Four articles on higher education curriculum are presented. In "The Articulate Curriculum" an approach to curriculum description is presented that is designed to have minimal ambiguity concerning the intention, content, and processes of the curriculum and that will lead to questioning several discrete factors in the curriculum planning process. It…

  9. Higher Education Exchange, 2013

    ERIC Educational Resources Information Center

    Brown, David W., Ed.; Witte, Deborah, Ed.

    2013-01-01

    The Kettering Foundation's research has been focused on putting the public back into the public's business for more than thirty years. Some questions that have recently been useful to Kettering researchers as the foundation focuses on its work with institutional actors--especially higher education and its relationship with the public--have…

  10. Online Higher Education Commodity

    ERIC Educational Resources Information Center

    Chau, Paule

    2010-01-01

    This article analyzes the current trend towards online education. It examines some of the reasons for the trend and the ramifications it may have on students, faculty and institutions of higher learning. The success and profitability of online programs and institutions such as the University of Phoenix has helped to make the move towards online…

  11. Developing Emotionally Intelligent Leadership in Higher Education

    ERIC Educational Resources Information Center

    Parrish, Dominique

    2011-01-01

    It is widely accepted that the success of higher education institutions is dependent on effective competent leaders and leadership. There is also growing evidence to support the proposition that emotional intelligence is strongly linked to effective leadership in the higher education setting. Additionally, the premise that emotional intelligence…

  12. The NEA 1994 Almanac of Higher Education.

    ERIC Educational Resources Information Center

    Wechsler, Harold, Ed.

    The 1994 edition of the NEA Almanac of Higher Education offers this year, in addition to the usual statistical data that the almanac has traditionally provided, seven articles that analyze important trends in higher education by leading scholars from across the nation. "Faculty Salaries, 1992-1993" by John B. Lee gives a detailed analysis of…

  13. Higher Education Accountability Report: 2009-10

    ERIC Educational Resources Information Center

    Washington Higher Education Coordinating Board, 2011

    2011-01-01

    This is the third Accountability Report published by the Higher Education Coordinating Board (HECB). This report fulfills the biennial requirement that the HECB inform the higher education and fiscal committees of the legislature of the system's progress toward goals. This report also fulfills an additional legislative requirement that calls…

  14. Effects of meat addition on pasta structure, nutrition and in vitro digestibility.

    PubMed

    Liu, Tingting; Hamid, Nazimah; Kantono, Kevin; Pereira, Loveena; Farouk, Mustafa M; Knowles, Scott O

    2016-12-15

    In our study, semolina flour was substituted with beef emulsion (EM) at three different levels of 15, 30 and 45% (w/w) to develop a pasta with enhanced nutritional profile. The protein, fat, and water content significantly increased with addition of meat. The addition of meat enhanced the pasta gluten network. The redness and yellowness of cooked pasta increased with meat addition. Tensile strength increased from 0.018N/mm(2) in the control sample to 0.046N/mm(2) in 45% beef emulsion (45EM) sample. All meat-containing samples had significantly higher elasticity than control (0.039N/mm(2)). GI significantly decreased and IVPD value increased in 45EM sample. Five essential amino acids (leucine, lysine, methionine, threonine, tryptophan) in pasta digesta increased significantly with increasing meat addition.

  15. Effects of meat addition on pasta structure, nutrition and in vitro digestibility.

    PubMed

    Liu, Tingting; Hamid, Nazimah; Kantono, Kevin; Pereira, Loveena; Farouk, Mustafa M; Knowles, Scott O

    2016-12-15

    In our study, semolina flour was substituted with beef emulsion (EM) at three different levels of 15, 30 and 45% (w/w) to develop a pasta with enhanced nutritional profile. The protein, fat, and water content significantly increased with addition of meat. The addition of meat enhanced the pasta gluten network. The redness and yellowness of cooked pasta increased with meat addition. Tensile strength increased from 0.018N/mm(2) in the control sample to 0.046N/mm(2) in 45% beef emulsion (45EM) sample. All meat-containing samples had significantly higher elasticity than control (0.039N/mm(2)). GI significantly decreased and IVPD value increased in 45EM sample. Five essential amino acids (leucine, lysine, methionine, threonine, tryptophan) in pasta digesta increased significantly with increasing meat addition. PMID:27451161

  16. Higher spins and holography

    NASA Astrophysics Data System (ADS)

    Kraus, Per; Ross, Simon F.

    2013-05-01

    The principles of quantum mechanics and relativity impose rigid constraints on theories of massless particles with nonzero spin. Indeed, Yang-Mills theory and General Relativity are the unique solution in the case of spin-1 and spin-2. In asymptotically flat spacetime, there are fundamental obstacles to formulating fully consistent interacting theories of particles of spin greater than 2. However, indications are that such theories are just barely possible in asymptotically anti-de Sitter or de Sitter spacetimes, where the non-existence of an S-matrix provides an escape from the theorems restricting theories in Minkowski spacetime. These higher spin gravity theories are therefore of great intrinsic interest, since they, along with supergravity, provide the only known field theories generalizing the local invariance principles of Yang-Mills theory and General Relativity. While work on higher spin gravity goes back several decades, the subject has gained broader appeal in recent years due to its appearance in the AdS/CFT correspondence. In three and four spacetime dimensions, there exist duality proposals linking higher spin gravity theories to specific conformal field theories living in two and three dimensions respectively. The enlarged symmetry algebra of the conformal field theories renders them exactly soluble, which makes them excellent laboratories for understanding in detail the holographic mechanism behind AdS/CFT duality. Steady progress is also being made on better understanding the space of possible higher spin gravity theories and their physical content. This work includes classifying the possible field multiplets and their interactions, constructing exact solutions of the nonlinear field equations, and relating higher spin theories to string theory. A full understanding of these theories will involve coming to grips with the novel symmetry principles that enlarge those of General Relativity and Yang-Mills theory, and one can hope that this will provide

  17. Extremal higher spin black holes

    NASA Astrophysics Data System (ADS)

    Bañados, Máximo; Castro, Alejandra; Faraggi, Alberto; Jottar, Juan I.

    2016-04-01

    The gauge sector of three-dimensional higher spin gravities can be formulated as a Chern-Simons theory. In this context, a higher spin black hole corresponds to a flat connection with suitable holonomy (smoothness) conditions which are consistent with the properties of a generalized thermal ensemble. Building on these ideas, we discuss a definition of black hole extremality which is appropriate to the topological character of 3 d higher spin theories. Our definition can be phrased in terms of the Jordan class of the holonomy around a non-contractible (angular) cycle, and we show that it is compatible with the zero-temperature limit of smooth black hole solutions. While this notion of extremality does not require supersymmetry, we exemplify its consequences in the context of sl(3|2) ⊕ sl(3|2) Chern-Simons theory and show that, as usual, not all extremal solutions preserve supersymmetries. Remarkably, we find in addition that the higher spin setup allows for non-extremal supersymmetric black hole solutions. Furthermore, we discuss our results from the perspective of the holographic duality between sl(3|2) ⊕ sl(3|2) Chern-Simons theory and two-dimensional CFTs with W (3|2) symmetry, the simplest higher spin extension of the N = 2 super-Virasoro algebra. In particular, we compute W (3|2) BPS bounds at the full quantum level, and relate their semiclassical limit to extremal black hole or conical defect solutions in the 3 d bulk. Along the way, we discuss the role of the spectral flow automorphism and provide a conjecture for the form of the semiclassical BPS bounds in general N = 2 two-dimensional CFTs with extended symmetry algebras.

  18. Transformation of Breast Reconstruction via Additive Biomanufacturing

    PubMed Central

    Chhaya, Mohit P.; Balmayor, Elizabeth R.; Hutmacher, Dietmar W.; Schantz, Jan-Thorsten

    2016-01-01

    Adipose tissue engineering offers a promising alternative to current breast reconstruction options. However, the conventional approach of using a scaffold in combination with adipose-derived precursor cells poses several problems in terms of scalability and hence clinical feasibility. Following the body-as-a-bioreactor approach, this study proposes a unique concept of delayed fat injection into an additive biomanufactured and custom-made scaffold. Three study groups were evaluated: Empty scaffold, Scaffold containing 4 cm3 lipoaspirate and Empty scaffold +2-week prevascularisation period. In group 3, of prevascularisation, 4 cm3 of lipoaspirate was injected into scaffolds after 2 weeks. Using a well-characterised additive biomanufacturing technology platform, patient-specific scaffolds made of medical-grade-polycaprolactone were designed and fabricated. Scaffolds were implanted in subglandular pockets in immunocompetent minipigs (n = 4) for 24-weeks. Angiogenesis and adipose tissue regeneration were observed in all constructs. Histological evaluation showed that the prevascularisation + lipoaspirate group had the highest relative area of adipose tissue (47.32% ± 4.12) which was significantly higher than both lipoaspirate-only (39.67% ± 2.04) and empty control group (8.31% ± 8.94) and similar to native breast tissue (44.97% ± 14.12). This large preclinical animal study provides proof-of-principle that the clinically applicable prevascularisation and delayed fat-injection techniques can be used for regeneration of large volumes of adipose tissue. PMID:27301425

  19. Effectiveness of antibacterial copper additives in silicone implants.

    PubMed

    Gosau, Martin; Bürgers, Ralf; Vollkommer, Tobias; Holzmann, Thomas; Prantl, Lukas

    2013-08-01

    Staphylococcus epidermidis plays a major role in capsular contractures of silicone breast implants. This in vitro study evaluates the antibacterial effect of copper on S. epidermidis in silicone implants. Specimens of a silicone material used for breast augmentation (Cu0) and specimens coated with different copper concentrations (Cu1, Cu2) were artificially aged. Surface roughness and surface free energy were assessed. The specimens were incubated in an S. epidermidis suspension. We assessed the quantification and the viability of adhering bacteria by live/dead cell labeling with fluorescence microscopy. Additionally, inhibition of bacterial growth was evaluated by agar diffusion, broth culture, and quantitative culture of surface bacteria. No significant differences in surface roughness and surface free energy were found between Cu0, Cu1 and Cu2. Aging did not change surface characteristics and the extent of bacterial adhesion. Fluorescence microscopy showed that the quantity of bacteria on Cu0 was significantly higher than that on Cu1 and Cu2. The ratio of dead to total adhering bacteria was significantly lower on Cu0 than on Cu1 and Cu2, and tended to be higher for Cu2 than for Cu1. Quantitative culture showed equal trends. Copper additives seem to have anti-adherence and bactericidal effects on S. epidermidis in vitro.

  20. Additively manufactured porous tantalum implants.

    PubMed

    Wauthle, Ruben; van der Stok, Johan; Amin Yavari, Saber; Van Humbeeck, Jan; Kruth, Jean-Pierre; Zadpoor, Amir Abbas; Weinans, Harrie; Mulier, Michiel; Schrooten, Jan

    2015-03-01

    The medical device industry's interest in open porous, metallic biomaterials has increased in response to additive manufacturing techniques enabling the production of complex shapes that cannot be produced with conventional techniques. Tantalum is an important metal for medical devices because of its good biocompatibility. In this study selective laser melting technology was used for the first time to manufacture highly porous pure tantalum implants with fully interconnected open pores. The architecture of the porous structure in combination with the material properties of tantalum result in mechanical properties close to those of human bone and allow for bone ingrowth. The bone regeneration performance of the porous tantalum was evaluated in vivo using an orthotopic load-bearing bone defect model in the rat femur. After 12 weeks, substantial bone ingrowth, good quality of the regenerated bone and a strong, functional implant-bone interface connection were observed. Compared to identical porous Ti-6Al-4V structures, laser-melted tantalum shows excellent osteoconductive properties, has a higher normalized fatigue strength and allows for more plastic deformation due to its high ductility. It is therefore concluded that this is a first step towards a new generation of open porous tantalum implants manufactured using selective laser melting.

  1. Additively manufactured porous tantalum implants.

    PubMed

    Wauthle, Ruben; van der Stok, Johan; Amin Yavari, Saber; Van Humbeeck, Jan; Kruth, Jean-Pierre; Zadpoor, Amir Abbas; Weinans, Harrie; Mulier, Michiel; Schrooten, Jan

    2015-03-01

    The medical device industry's interest in open porous, metallic biomaterials has increased in response to additive manufacturing techniques enabling the production of complex shapes that cannot be produced with conventional techniques. Tantalum is an important metal for medical devices because of its good biocompatibility. In this study selective laser melting technology was used for the first time to manufacture highly porous pure tantalum implants with fully interconnected open pores. The architecture of the porous structure in combination with the material properties of tantalum result in mechanical properties close to those of human bone and allow for bone ingrowth. The bone regeneration performance of the porous tantalum was evaluated in vivo using an orthotopic load-bearing bone defect model in the rat femur. After 12 weeks, substantial bone ingrowth, good quality of the regenerated bone and a strong, functional implant-bone interface connection were observed. Compared to identical porous Ti-6Al-4V structures, laser-melted tantalum shows excellent osteoconductive properties, has a higher normalized fatigue strength and allows for more plastic deformation due to its high ductility. It is therefore concluded that this is a first step towards a new generation of open porous tantalum implants manufactured using selective laser melting. PMID:25500631

  2. Neutron Characterization for Additive Manufacturing

    NASA Technical Reports Server (NTRS)

    Watkins, Thomas; Bilheux, Hassina; An, Ke; Payzant, Andrew; DeHoff, Ryan; Duty, Chad; Peter, William; Blue, Craig; Brice, Craig A.

    2013-01-01

    Oak Ridge National Laboratory (ORNL) is leveraging decades of experience in neutron characterization of advanced materials together with resources such as the Spallation Neutron Source (SNS) and the High Flux Isotope Reactor (HFIR) shown in Fig. 1 to solve challenging problems in additive manufacturing (AM). Additive manufacturing, or three-dimensional (3-D) printing, is a rapidly maturing technology wherein components are built by selectively adding feedstock material at locations specified by a computer model. The majority of these technologies use thermally driven phase change mechanisms to convert the feedstock into functioning material. As the molten material cools and solidifies, the component is subjected to significant thermal gradients, generating significant internal stresses throughout the part (Fig. 2). As layers are added, inherent residual stresses cause warping and distortions that lead to geometrical differences between the final part and the original computer generated design. This effect also limits geometries that can be fabricated using AM, such as thin-walled, high-aspect- ratio, and overhanging structures. Distortion may be minimized by intelligent toolpath planning or strategic placement of support structures, but these approaches are not well understood and often "Edisonian" in nature. Residual stresses can also impact component performance during operation. For example, in a thermally cycled environment such as a high-pressure turbine engine, residual stresses can cause components to distort unpredictably. Different thermal treatments on as-fabricated AM components have been used to minimize residual stress, but components still retain a nonhomogeneous stress state and/or demonstrate a relaxation-derived geometric distortion. Industry, federal laboratory, and university collaboration is needed to address these challenges and enable the U.S. to compete in the global market. Work is currently being conducted on AM technologies at the ORNL

  3. Photoactive devices including porphyrinoids with coordinating additives

    DOEpatents

    Forrest, Stephen R; Zimmerman, Jeramy; Yu, Eric K; Thompson, Mark E; Trinh, Cong; Whited, Matthew; Diev, Vlacheslav

    2015-05-12

    Coordinating additives are included in porphyrinoid-based materials to promote intermolecular organization and improve one or more photoelectric characteristics of the materials. The coordinating additives are selected from fullerene compounds and organic compounds having free electron pairs. Combinations of different coordinating additives can be used to tailor the characteristic properties of such porphyrinoid-based materials, including porphyrin oligomers. Bidentate ligands are one type of coordinating additive that can form coordination bonds with a central metal ion of two different porphyrinoid compounds to promote porphyrinoid alignment and/or pi-stacking. The coordinating additives can shift the absorption spectrum of a photoactive material toward higher wavelengths, increase the external quantum efficiency of the material, or both.

  4. Higher-spin theory and holography

    NASA Astrophysics Data System (ADS)

    Gaberdiel, Matthias; Vasiliev, Mikhail

    2013-05-01

    , this has triggered a significant amount of activity in this general area. Among other things, the constraints that are implied by the higher-spin symmetries were analysed (see the paper by Maldacena and Zhiboedov in this issue [9]), and a fairly concrete proposal for how higher-spin theories are related to string theory was made (see the paper by Chang, Minwalla, Sharma and Yin in this issue [10]). Furthermore, a lower dimensional version of the conjecture was put forward by Gaberdiel and Gopakumar [11] that was subsequently also checked in some detail. These dualities hold the promise of offering insights into the inner workings of the AdS/CFT correspondence since they are complex enough to capture the essence of the duality, while at the same time being sufficiently simple in order to allow for a detailed analysis. Moreover, the methods specifically developed in higher-spin theory may be useful for understanding a general mechanism underlying holography, both in higher-spin models and beyond (see the paper by Vasiliev in this issue [12]). Another fascinating aspect of these higher-spin theories lies in the fact that the higher-spin symmetries mix generically fields of different spin, and in particular, the spin-2 metric and higher-spin excitations are related to one another by gauge transformations. As a result, higher-spin theories require a modification of the standard framework of Riemannian geometry since the usual diffeomorphism-invariant tensors are not gauge invariant any longer. In particular, higher-spin theories may therefore open the way towards understanding fundamental concepts of space-time geometry; for example, they may well have key lessons in store for how string theory resolves space-time singularities. In this issue we have collected together a number of review papers, summarizing the aforementioned recent developments, as well as research papers indicating current directions of interest in the study of higher-spin gauge theories. We hope that it

  5. Additive and non-additive genetic components of the jack male life history in Chinook salmon (Oncorhynchus tshawytscha).

    PubMed

    Forest, Adriana R; Semeniuk, Christina A D; Heath, Daniel D; Pitcher, Trevor E

    2016-08-01

    Chinook salmon, Oncorhynchus tshawytscha, exhibit alternative reproductive tactics (ARTs) where males exist in two phenotypes: large "hooknose" males and smaller "jacks" that reach sexual maturity after only 1 year in seawater. The mechanisms that determine "jacking rate"-the rate at which males precociously sexually mature-are known to involve both genetics and differential growth rates, where individuals that become jacks exhibit higher growth earlier in life. The additive genetic components have been studied and it is known that jack sires produce significantly more jack offspring than hooknose sires, and vice versa. The current study was the first to investigate both additive and non-additive genetic components underlying jacking through the use of a full-factorial breeding design using all hooknose sires. The effect of dams and sires descendant from a marker-assisted broodstock program that identified "high performance" and "low performance" lines using growth- and survival-related gene markers was also studied. Finally, the relative growth of jack, hooknose, and female offspring was examined. No significant dam, sire, or interaction effects were observed in this study, and the maternal, additive, and non-additive components underlying jacking were small. Differences in jacking rates in this study were determined by dam performance line, where dams that originated from the low performance line produced significantly more jacks. Jack offspring in this study had a significantly larger body size than both hooknose males and females starting 1 year post-fertilization. This study provides novel information regarding the genetic architecture underlying ARTs in Chinook salmon that could have implications for the aquaculture industry, where jacks are not favoured due to their small body size and poor flesh quality. PMID:27450674

  6. Additive and non-additive genetic components of the jack male life history in Chinook salmon (Oncorhynchus tshawytscha).

    PubMed

    Forest, Adriana R; Semeniuk, Christina A D; Heath, Daniel D; Pitcher, Trevor E

    2016-08-01

    Chinook salmon, Oncorhynchus tshawytscha, exhibit alternative reproductive tactics (ARTs) where males exist in two phenotypes: large "hooknose" males and smaller "jacks" that reach sexual maturity after only 1 year in seawater. The mechanisms that determine "jacking rate"-the rate at which males precociously sexually mature-are known to involve both genetics and differential growth rates, where individuals that become jacks exhibit higher growth earlier in life. The additive genetic components have been studied and it is known that jack sires produce significantly more jack offspring than hooknose sires, and vice versa. The current study was the first to investigate both additive and non-additive genetic components underlying jacking through the use of a full-factorial breeding design using all hooknose sires. The effect of dams and sires descendant from a marker-assisted broodstock program that identified "high performance" and "low performance" lines using growth- and survival-related gene markers was also studied. Finally, the relative growth of jack, hooknose, and female offspring was examined. No significant dam, sire, or interaction effects were observed in this study, and the maternal, additive, and non-additive components underlying jacking were small. Differences in jacking rates in this study were determined by dam performance line, where dams that originated from the low performance line produced significantly more jacks. Jack offspring in this study had a significantly larger body size than both hooknose males and females starting 1 year post-fertilization. This study provides novel information regarding the genetic architecture underlying ARTs in Chinook salmon that could have implications for the aquaculture industry, where jacks are not favoured due to their small body size and poor flesh quality.

  7. Glacial marine sedimentation: Paleoclimatic significance

    SciTech Connect

    Anderson, J.B.; Ashley, G.M.

    1991-01-01

    This publication resulted from a symposium held during the 1988 Annual Meeting of the Geological Society of America. Many, but not all, contributors to the symposium have papers in this volume. This Special Paper consists of 14 chapters and a Subject/Geographic index. Each chapter has is own list of references. The papers cover a wide range of modem climate/ ocean environments, including papers on glacial marine sediments from Antarctica, the fiords of Alaska, and sediments from the Canadian High Arctic. In addition, three papers discuss [open quote]old[close quotes] glacial marine records (i.e., pre-Tertiary), and one paper discusses the Yakataga Formation of the Gulf of Alaska which is a Miocene-to-late-Pleistocene sequence. The last chapter in the book includes a survey and summary of the evidence for the paleoclimatic significance of glacial marine sediments by the two editors, John Anderson and Gail Ashley. It is worth noting that Anderson and Domack state in the Foreword that there is a considerable variation in terminology; hence they employ a series of definitions which they urge the other authors to employ. They define and explain what they mean by [open quotes]polar ice cap,[close quotes] [open quote]polar tundra (subpolar),[close quotes] and [open quotes]temperate oceanic and boreal[close quotes] in terms of the dominant glacial and glacial marine processes. Although one might quarrel with the terminology, the broad differences between these three glaciological regimes are indeed fundamental and need to be sought in the geological record. The flavor of the volume can be judged by some of the chapter titles. Contributions on Antarctica include a paper by Anderson and other entitled [open quote]Sedimentary facies associated with Antarctica's floating ice masses[close quotes] and a companion paper by Anderson and Domack which deals with the extremely complex glacial marine facies (13 facies are delimited) in McMurdo Sound, Antarctica.

  8. Higher than Everest

    NASA Astrophysics Data System (ADS)

    Hodge, Paul

    2001-08-01

    Tired of exploring planet Earth? Have you ever imagined what it would be like to explore the Moon? Ever wonder about the topography of Mars? In this unique guidebook all of your extraterrestrial wanderlust can be fulfilled as Paul Hodge takes you on a virtual tour of the most spectacular sites in the Solar System. Hodge includes the latest information about the Solar System into his vivid descriptions of imaginary, challenging expeditions. Imagine: -- Descending into a fabulous canyon on Mars, one that dwarfs the Earth's Grand Canyon; -- Trekking up Venus' precipitous and scorching Mt. Maxwell; -- Journeying through the snows of Saturn's rings and the incredibly high, icy cliff of Miranda, the moon closest to Uranus. A compelling, extensively illustrated introduction to such otherworldly environments, Higher than Everest makes you believe that someday these adventures may actually take place. Paul Hodge is Professor of Astronomy at the University of Washington, Seattle, and Editor-in-Chief of the Astronomical Journal. Higher than Everest is based on a popular undergraduate course on the planets that he has taught for many years. Hodge's research has spanned from interplanetary dust to the extragalactic distance scale and currently includes star-formation and galactic evolution, using the Hubble Space Telescope to investigate nearby galaxies. He has written several books, most recently Meteorite Craters and Impact Structures of the Earth (Cambridge 1994).

  9. Higher harmonic generation microscopy.

    PubMed

    Sun, Chi-Kuang

    2005-01-01

    Higher harmonic-generation, including second harmonic generation and third harmonic generation, leaves no energy deposition to the interacted matters due to its virtual-level transition characteristic, providing a truly non-invasive modality and is ideal for in vivo imaging of live specimens without any preparation. Second harmonic generation microscopy provides images on stacked membranes and arranged proteins with organized nano-structures due to the bio-photonic crystalline effect. Third harmonic generation microscopy provides general cellular or subcellular interface imaging due to optical inhomogeneity. Due to their virtual-transition nature, no saturation or bleaching in the generated signal is expected. With no energy release, continuous viewing without compromising sample viability can thus be achieved. Combined with its nonlinearity, higher harmonic generation microscopy provides sub-micron three-dimensional sectioning capability and millimeter penetration in live samples without using fluorescence and exogenous markers, offering morphological, structural, functional, and cellular information of biomedical specimens without modifying their natural biological and optical environments.

  10. Significantly higher frequency of Helicobacter suis in patients with idiopathic parkinsonism than in control patients

    PubMed Central

    Blaecher, C; Smet, A; Flahou, B; Pasmans, F; Ducatelle, R; Taylor, D; Weller, C; Bjarnason, I; Charlett, A; Lawson, A J; Dobbs, R J; Dobbs, S M; Haesebrouck, F

    2013-01-01

    Background There is increased proportional mortality from Parkinson's disease amongst livestock farmers. The hypokinesia of Parkinson's disease has been linked to Helicobacter pylori. H. suis is the most common zoonotic helicobacter in man. Aim To compare the frequency of H. suis, relative to H. pylori, in gastric biopsies of patients with idiopathic parkinsonism (IP) and controls from gastroenterology services. Methods DNA extracts, archived at a Helicobacter Reference Laboratory, from IP patient and gastroenterology service biopsies were examined anonymously for H. suis, using species-specific RT-PCR. Results Relative risk of having H. suis in 60 IP patients compared with 256 controls was 10 times greater than that of having H. pylori. In patients with IP and controls, respectively, frequencies of H. suis were 27 (exact binomial 95% C.I. 15, 38) and 2 (0, 3)%, and of H. pylori, 28 (17, 40) and 16 (12, 21)%. Excess of H. suis in IP held when only the antral or corporal biopsy was considered. Of 16 IP patients with H. suis, 11 were from 19 with proven H. pylori eradication, 3 from 17 pre-H. pylori eradication, 2 from 24 H. pylori culture/PCR-negative. Frequency was different between groups (P = 0.001), greatest where H. pylori had been eradicated. Even without known exposure to anti-H. pylori therapy, H. suis was more frequent in IP patients (5/41) than in controls (1/155) (P = 0.002). Partial multilocus sequence typing confirmed that strains from IP patients (6) and control (1) differed from RT-PCR standard strain. Conclusions Greater frequency of H. suis in idiopathic parkinsonism appears exaggerated following H. pylori eradication. Multilocus sequence testing comparison with porcine strains may clarify whether transmission is from pigs/porcine products or of human-adapted, H. suis-like, bacteria. PMID:24117797

  11. Knowing Feminism: The Significance of Higher Education to Women's Narratives of "Becoming Feminist"

    ERIC Educational Resources Information Center

    Guest, Carly Joanne

    2016-01-01

    Educational spaces have long provided opportunities for politicisation and activism. However, research into the processes through which students become politicised can often focus on participation in recognised forms of political action, thereby ignoring the multiple factors active in developing a political consciousness. This paper draws on…

  12. First-Generation Female Higher Education Student Affairs Personnel: The Significance of Personality and Spirituality

    ERIC Educational Resources Information Center

    Albert, Jennifer L.

    2014-01-01

    A cohort of 15 participants was chosen to engage in a study to identify a relationship between personality type and the propensity to choose professions in student affairs. Participants were chosen based upon specific demographic criteria in an effort to highlight inconsistencies in traditionally accepted variables, including gender, ethnicity,…

  13. Significance of higher-order multiple scattering for laser beam propagation through hazes, fogs, and clouds.

    PubMed

    Deepak, A; Farrukh, U O; Zardecki, A

    1982-02-01

    An approach is outlined for computing the different orders of scattering in any medium that possesses a phase function with a strong forward peak. Computations are done for the case of a Gaussian laser beam incident on such a medium. The formulation adopted does reproduce the natural divergence of general Gaussian beams without the need to assume the presence of point sources or the need to assume perfectly collimated beams within the region of interest. Results are discussed for the case of water cloud particles with a strongly forward-peaked phase function for the incident laser radiation.

  14. Oral symptoms significantly higher among long-term khat (Catha edulis) users in Ethiopia

    PubMed Central

    Astatkie, Ayalew; Demissie, Meaza; Berhane, Yemane; Worku, Alemayehu

    2015-01-01

    OBJECTIVES: Associations between khat (Catha edulis) chewing and different adverse oral-dental health conditions have been reported, yet evidence is still lacking. This study was designed to investigate the association between long-term regular khat chewing and self-reported oral symptoms. METHODS: A cross-sectional study was conducted on a sample of 1,255 university students in southern Ethiopia. Data on khat chewing status, a range of oral symptoms and other pertinent variables were collected using self-administered questionnaires. The association between long-term regular khat chewing and oral symptom count was investigated using negative binomial regression. RESULTS: The mean oral symptom count among long-term regular khat chewers was 1.75 (standard deviation [SD], 2.18; standard error [SE], 0.31), whereas that among those who were not long-term regular khat chewers was 1.18 (SD, 1.68; SE, 0.10). After adjustment for other variables, long-term regular khat chewers had approximately 50% more oral symptoms than those who were not long-term chewers did (adjusted count ratio, 1.53; 95% confidence interval, 1.12 to 2.10). CONCLUSIONS: Long-term khat chewing negatively affects the oral health of young university students. PMID:25773437

  15. Higher dimensional massive bigravity

    NASA Astrophysics Data System (ADS)

    Do, Tuan Q.

    2016-08-01

    We study higher-dimensional scenarios of massive bigravity, which is a very interesting extension of nonlinear massive gravity since its reference metric is assumed to be fully dynamical. In particular, the Einstein field equations along with the following constraint equations for both physical and reference metrics of a five-dimensional massive bigravity will be addressed. Then, we study some well-known cosmological spacetimes such as the Friedmann-Lemaitre-Robertson-Walker, Bianchi type I, and Schwarzschild-Tangherlini metrics for the five-dimensional massive bigravity. As a result, we find that massive graviton terms will serve as effective cosmological constants in both physical and reference sectors if a special scenario, in which reference metrics are chosen to be proportional to physical ones, is considered for all mentioned metrics. Thanks to the constancy property of massive graviton terms, consistent cosmological solutions will be figured out accordingly.

  16. "Clinical" Significance: "Clinical" Significance and "Practical" Significance are NOT the Same Things

    ERIC Educational Resources Information Center

    Peterson, Lisa S.

    2008-01-01

    Clinical significance is an important concept in research, particularly in education and the social sciences. The present article first compares clinical significance to other measures of "significance" in statistics. The major methods used to determine clinical significance are explained and the strengths and weaknesses of clinical significance…

  17. Comparative Higher Education. Research Trends and Bibliography.

    ERIC Educational Resources Information Center

    Altbach, Philip G.

    Consisting of an essay and a bibliography, this book provides a discussion of the origins and development of comparative higher education as a field of study, an interpretation of the key issues in higher education as they affect different countries, and a select list of significant contributions to the literature on the subject. The essay begins…

  18. SREB Fact Book On Higher Education 1988.

    ERIC Educational Resources Information Center

    Marks, Joseph L.

    The Southern Regional Education Board (SREB) Fact Book presents the latest available information on significant national, regional, and SREB-state trends affecting higher education. Trends are presented from SREB's extensive databases on demographics, elementary/secondary education, higher education institutions and their enrollments, degrees…

  19. Planning for Higher Education. Background and Application.

    ERIC Educational Resources Information Center

    Pfnister, Allan O.

    Written to bring together some of the more significant writing about developments in higher education during the past decade, to organize the wide range of commentaries and studies, and to show the administrator, faculty member, and informed layman what the current status of American higher education appears to be, this book emphasizes trends in…

  20. Theorising Student Engagement in Higher Education

    ERIC Educational Resources Information Center

    Kahn, Peter E.

    2014-01-01

    Student engagement has become problematic following the rise of mass and universal forms of higher education. Significant attention has been devoted to identifying factors that are associated with higher levels of engagement, but it remains the case that the underlying reasons for student engagement and, indeed, the notion itself of "student…

  1. Higher prices in Jamaica.

    PubMed

    1982-03-01

    Price increases in the Jamaica CSM program went into effect on August 31, 1981. The program began in 1975. While the need for higher prices has been under discussion for the past 3 years, this is the 1st time the requisite approval from the Jamaica Price Commission has been obtained. The Jamaica National Family Planning Board (JNFPB) reports that the Panther 3-pack (condom) is up US$0.15 to US$0.30. Each Perle package (oral contraceptive) was increased by US$0.20. Single cycle Perle now sells for US$0.50, and 3-pack Perle sells for US$1.10. The 6-year price stagnation experienced by the CSM program resulted in a decreasing operational budget as program costs continued to rise. Marketing costs alone during this period escalated by 100-300%. For example, Panther pop-up display cartons cost the project US 16U each in 1975. By 1979 the same product cost US 49U. Newspaper advertisements have increased from the 1975 cost of US$68.00 to nearly $200.00 per placement. The overall inflation rate in Jamaica during the last 5 years has averaged more than 20% annually. In the face of these rising costs, outlet expansion for Perle has been prevented, wholesaler margins have been unavailable, and new retailer training has been discontinued. It is projected that the new prices will result in an annual increased revenues of US$80,000 which will be used to reinstate these essential marketing activities. The JNFPB is also planning to introduce a Panther 12-pack and Panther strips to the CSM product line. According to Marketing Manager Aston Evans, "We believe the public is now ready for this type of packaging" which is scheduled to be available soon. Panther is presently only available in a 3-pack, but annual sales have been steady. The new 12-pack will be stocked on supermarket shelves to provide higher product visibility and wider distribution. The selling price has been set as US$1.20 and is expected to yield a 25% increase in sales during the 1st year. A complete sales promotion

  2. Boiling significantly promotes photodegradation of perfluorooctane sulfonate.

    PubMed

    Lyu, Xian-Jin; Li, Wen-Wei; Lam, Paul K S; Yu, Han-Qing

    2015-11-01

    The application of photochemical processes for perfluorooctane sulfonate (PFOS) degradation has been limited by a low treatment efficiency. This study reports a significant acceleration of PFOS photodegradation under boiling condition compared with the non-boiling control. The PFOS decomposition rate increased with the increasing boiling intensity, but declined at a higher hydronium level or under oxygenation. These results suggest that the boiling state of solution resulted in higher effective concentrations of reactants at the gas-liquid interface and enhanced the interfacial mass transfer, thereby accelerating the PFOS decomposition. This study broadens our knowledge of PFOS photodegradation process and may have implications for development of efficient photodegradation technologies. PMID:26117498

  3. Boiling significantly promotes photodegradation of perfluorooctane sulfonate.

    PubMed

    Lyu, Xian-Jin; Li, Wen-Wei; Lam, Paul K S; Yu, Han-Qing

    2015-11-01

    The application of photochemical processes for perfluorooctane sulfonate (PFOS) degradation has been limited by a low treatment efficiency. This study reports a significant acceleration of PFOS photodegradation under boiling condition compared with the non-boiling control. The PFOS decomposition rate increased with the increasing boiling intensity, but declined at a higher hydronium level or under oxygenation. These results suggest that the boiling state of solution resulted in higher effective concentrations of reactants at the gas-liquid interface and enhanced the interfacial mass transfer, thereby accelerating the PFOS decomposition. This study broadens our knowledge of PFOS photodegradation process and may have implications for development of efficient photodegradation technologies.

  4. Effect of urea addition on giant reed ensilage and subsequent methane production by anaerobic digestion.

    PubMed

    Liu, Shan; Ge, Xumeng; Liew, Lo Niee; Liu, Zhe; Li, Yebo

    2015-09-01

    The effect of urea addition on giant reed ensilage and sequential anaerobic digestion (AD) of the ensiled giant reed was evaluated. The dry matter loss during ensilage (up to 90 days) with or without urea addition was about 1%. Addition of 2% urea enhanced production of lactic acid by about 4 times, and reduced production of propionic acid by 2-8 times. Besides, urea addition reduced degradation of cellulose and hemicellulose, and increased degradation of lignin in giant reed during ensilage. Ensilage with or without urea addition had no significant effects on the enzymatic digestibility of giant reed, but ensilage with urea addition achieved a cumulative methane yield of 173 L/kg VS, which was 18% higher than that of fresh giant reed. The improved methane yield of giant reed could be attributed to the production of organic acids and ethanol during ensilage.

  5. Incorporation of additives into polymers

    DOEpatents

    McCleskey, T. Mark; Yates, Matthew Z.

    2003-07-29

    There has been invented a method for incorporating additives into polymers comprising: (a) forming an aqueous or alcohol-based colloidal system of the polymer; (b) emulsifying the colloidal system with a compressed fluid; and (c) contacting the colloidal polymer with the additive in the presence of the compressed fluid. The colloidal polymer can be contacted with the additive by having the additive in the compressed fluid used for emulsification or by adding the additive to the colloidal system before or after emulsification with the compressed fluid. The invention process can be carried out either as a batch process or as a continuous on-line process.

  6. [Patch-testing methods: additional specialised or additional series].

    PubMed

    Cleenewerck, M-B

    2009-01-01

    The tests in the European standard battery must occasionally be supplemented by specialised or additional batteries, particularly where the contact allergy is thought to be of occupational origin. These additional batteries cover all allergens associated with various professional activities (hairdressing, baking, dentistry, printing, etc.) and with different classes of materials and chemical products (glue, plastic, rubber...). These additional tests may also include personal items used by patients on a daily basis such as cosmetics, shoes, plants, textiles and so on.

  7. Additive manufacturing of optical components

    NASA Astrophysics Data System (ADS)

    Heinrich, Andreas; Rank, Manuel; Maillard, Philippe; Suckow, Anne; Bauckhage, Yannick; Rößler, Patrick; Lang, Johannes; Shariff, Fatin; Pekrul, Sven

    2016-08-01

    The development of additive manufacturing methods has enlarged rapidly in recent years. Thereby, the work mainly focuses on the realization of mechanical components, but the additive manufacturing technology offers a high potential in the field of optics as well. Owing to new design possibilities, completely new solutions are possible. This article briefly reviews and compares the most important additive manufacturing methods for polymer optics. Additionally, it points out the characteristics of additive manufactured polymer optics. Thereby, surface quality is of crucial importance. In order to improve it, appropriate post-processing steps are necessary (e.g. robot polishing or coating), which will be discussed. An essential part of this paper deals with various additive manufactured optical components and their use, especially in optical systems for shape metrology (e.g. borehole sensor, tilt sensor, freeform surface sensor, fisheye lens). The examples should demonstrate the potentials and limitations of optical components produced by additive manufacturing.

  8. Method of increasing enhanced oil recovery by using a higher sulfonate phase obtained on polymer addition

    SciTech Connect

    Carlin, J.T.

    1987-01-13

    A process is described for enhanced hydrocarbon recovery comprising: dissolving a polymer from the group consisting of polyacrylamides and polysaccharides in a surfactant flood fluid resulting from mixing water, petroleum sulfonate-containing surfactant and solubilizer; allowing the mixture to separate; using the fraction with the highest sulfonate content as a surfactant fluid; forcing the fluid through the formation and recovering the hydrocarbons, wherein the proportion of the sulfonate-containing surfactant, solubilizer and polymer is about 0.5% to 20.0% of total solute by weight of petroleum sulfonate surfactant, about 0.1% to about 5% by weight of a solubilizer and about 0.1% to 10% by weight of polymer.

  9. Prognostic significance of astrocyte elevated gene-1 in human astrocytomas

    PubMed Central

    He, Zhangxiu; He, Meihui; Wang, Chao; Xu, Baozhan; Tong, Liping; He, Junming; Sun, Bowen; Wei, Lanlan; Chu, Ming

    2014-01-01

    Astrocyte Elevated Gene-1 (AEG-1) has been proposed as a biomarker for a variety of cancers. This study aimed to investigate the expression of AEG-1 in human astrocytomas and the correlation between AEG-1 expression and clinicopathologic variables of astrocytomas. AEG-1 expression in four pairs of matched astrocytomas tissues and 5 cell lines was detected by immunohistochemical and Western blot analysis. In addition, AEG-1 protein expression was examined by immunohistochemical staining in 204 cases, including 32 normal brain tissues, 80 Low-malignant astrocytomas (LMAs) and 92 High-Malignant astrocytomas (HMAs). AEG-1 expression in 31 LMAs and 29 HMAs samples was detected by RT-PCR and Western blot analysis. We detected AEG-1 expression in normal neurons and glioma cell lines U87, U251 and M059K, but not in normal glial cells. Immunohistochemical analysis showed that 128 of 172 (74.4%) paraffin-embedded archival astrocytomas samples exhibited positive AEG-1 expression. Statistical analysis suggested that higher AEG-1 level was significantly correlated with histological grade of astrocytomas. In addition, AEG-1 mRNA and protein expression was higher in HMAs than in LMAs. AEG-1 expression had no correlation with the gender or age of astrocytoma patients. In summary, our data suggest that AEG-1 may represent a novel prognostic marker for astrocytomas. PMID:25197376

  10. Texas Higher Education in Transition.

    ERIC Educational Resources Information Center

    Texas Coll. and Univ. System, Austin. Coordinating Board.

    The status of higher education in Texas is examined in this major report of changes in higher education over the past decade. Information on enrollment, cost, financial aid, job opportunities, and facilities in higher education institutions is given for private higher education, professional higher education, community colleges, and state colleges…

  11. Additional waves in the graphene layered medium.

    PubMed

    Chern, Ruey-Lin; Han, Dezhuan; Zhang, Z Q; Chan, C T

    2014-12-29

    We investigate the features of additional waves that arise in the graphene layered medium, within the framework of nonlocal effective medium model. The additional wave is manifest on the biquadratic dispersion relation of the medium and represents as a distinctive nonlocal character at long wavelength. In particular, the reflection and transmission coefficients for the nonlocal medium are underdetermined by Maxwell's boundary conditions. An additional boundary condition based on modal expansions is proposed to derive the generalized Fresnel equations, based on which the additional wave in the graphene layered medium is determined. The additional wave tends to be significant near the effective plasma frequency, near which the graphene plasmons are excited inside the medium. PMID:25607138

  12. Higher Education in Yugoslavia. Yale Higher Education Research Group Working Paper.

    ERIC Educational Resources Information Center

    Giles, Geoffrey

    Historical data and the current status of higher education in Yugoslavia are examined. Among the reforms enacted was the General Law on Faculties and Universities of 1960. The major and most immediate effect was probably the explosive expansion of institutions, particularly between 1960 and 1963. Additionally, higher education was no longer…

  13. Enantioselective Michael Addition of Water

    PubMed Central

    Chen, Bi-Shuang; Resch, Verena; Otten, Linda G; Hanefeld, Ulf

    2015-01-01

    The enantioselective Michael addition using water as both nucleophile and solvent has to date proved beyond the ability of synthetic chemists. Herein, the direct, enantioselective Michael addition of water in water to prepare important β-hydroxy carbonyl compounds using whole cells of Rhodococcus strains is described. Good yields and excellent enantioselectivities were achieved with this method. Deuterium labeling studies demonstrate that a Michael hydratase catalyzes the water addition exclusively with anti-stereochemistry. PMID:25529526

  14. Enantioselective Michael addition of water.

    PubMed

    Chen, Bi-Shuang; Resch, Verena; Otten, Linda G; Hanefeld, Ulf

    2015-02-01

    The enantioselective Michael addition using water as both nucleophile and solvent has to date proved beyond the ability of synthetic chemists. Herein, the direct, enantioselective Michael addition of water in water to prepare important β-hydroxy carbonyl compounds using whole cells of Rhodococcus strains is described. Good yields and excellent enantioselectivities were achieved with this method. Deuterium labeling studies demonstrate that a Michael hydratase catalyzes the water addition exclusively with anti-stereochemistry.

  15. Gasoline additives, emissions, and performance

    SciTech Connect

    1995-12-31

    The papers included in this publication deal with the influence of fuel, additive, and hardware changes on a variety of vehicle performance characteristics. Advanced techniques for measuring these performance parameters are also described. Contents include: Fleet test evaluation of gasoline additives for intake valve and combustion chamber deposit clean up; A technique for evaluating octane requirement additives in modern engines on dynamometer test stands; A fleet test of two additive technologies comparing their effects on tailpipe emissions; Investigation into the vehicle exhaust emissions of high percentage ethanol blends; Variability in hydrocarbon speciation measurements at low emission (ULEV) levels; and more.

  16. Significance of Lead Residues in Mallard Tissues

    USGS Publications Warehouse

    Longcore, J.R.; Locke, L.N.; Bagley, G.E.; Andrews, R.

    1974-01-01

    Tissues of adult, lead-dosed mallards that either died or were sacrificed were analyzed for lead. Lead levels in brains, tibiae, and breast muscle of ducks that died and in tibiae of ducks that were sacrificed increased significantly from dosage until death. Lead in the heart, lung, and blood from sacrificed ducks decreased significantly from dosage until death. Lead concentrations in tissues from ducks in the two groups were not significantly different except for the liver, kidney, and lung. Average lead levels in the livers and kidneys of ducks that died were significantly higher than those in ducks that were sacrificed. The mean concentration of lead in the lungs of the ducks sacrificed was significantly higher than the mean level in the lungs of ducks that died. Measurements of the lead concentrations in this study, when compared with lead levels reported in the literature for avian and non-avian species, showed that arbitrary diagnostic levels indicating lead poisoning could be set. In mallard ducks, lead levels exceeding 3 ppm in the brain, 6 to 20 ppm in the kidney or liver, or 10 ppm in clotted blood from the heart indicated acute exposure to lead.

  17. Color Addition and Subtraction Apps

    ERIC Educational Resources Information Center

    Ruiz, Frances; Ruiz, Michael J.

    2015-01-01

    Color addition and subtraction apps in HTML5 have been developed for students as an online hands-on experience so that they can more easily master principles introduced through traditional classroom demonstrations. The evolution of the additive RGB color model is traced through the early IBM color adapters so that students can proceed step by step…

  18. Additive manufacturing of materials: Opportunities and challenges

    SciTech Connect

    Babu, Sudarsanam Suresh; Love, Lonnie J.; Dehoff, Ryan R.; Peter, William H.; Watkins, Thomas R.; Pannala, Sreekanth

    2015-11-01

    Additive manufacturing (also known as 3D printing) is considered a disruptive technology for producing components with topologically optimized complex geometries as well as functionalities that are not achievable by traditional methods. The realization of the full potential of 3D printing is stifled by a lack of computational design tools, generic material feedstocks, techniques for monitoring thermomechanical processes under in situ conditions, and especially methods for minimizing anisotropic static and dynamic properties brought about by microstructural heterogeneity. In this paper, we discuss the role of interdisciplinary research involving robotics and automation, process control, multiscale characterization of microstructure and properties, and high-performance computational tools to address each of these challenges. In addition, emerging pathways to scale up additive manufacturing of structural materials to large sizes (>1 m) and higher productivities (5–20 kg/h) while maintaining mechanical performance and geometrical flexibility are also discussed.

  19. Additive manufacturing of materials: Opportunities and challenges

    DOE PAGES

    Babu, Sudarsanam Suresh; Love, Lonnie J.; Dehoff, Ryan R.; Peter, William H.; Watkins, Thomas R.; Pannala, Sreekanth

    2015-11-01

    Additive manufacturing (also known as 3D printing) is considered a disruptive technology for producing components with topologically optimized complex geometries as well as functionalities that are not achievable by traditional methods. The realization of the full potential of 3D printing is stifled by a lack of computational design tools, generic material feedstocks, techniques for monitoring thermomechanical processes under in situ conditions, and especially methods for minimizing anisotropic static and dynamic properties brought about by microstructural heterogeneity. In this paper, we discuss the role of interdisciplinary research involving robotics and automation, process control, multiscale characterization of microstructure and properties, and high-performancemore » computational tools to address each of these challenges. In addition, emerging pathways to scale up additive manufacturing of structural materials to large sizes (>1 m) and higher productivities (5–20 kg/h) while maintaining mechanical performance and geometrical flexibility are also discussed.« less

  20. Significance of stem cell marker Nanog gene in the diagnosis and prognosis of lung cancer

    PubMed Central

    Liu, Zeng; Zhang, Jing; Kang, Honggang; Sun, Guiming; Wang, Baozhong; Wang, Yanwen; Yang, Mengxiang

    2016-01-01

    The aim of the present study was to analyze the stem cell marker, Nanog gene, for the diagnosis and prognosis of lung cancer cases, and to study its application in the diagnosis of lung cancer. In total, 100 patients diagnosed with lung cancer between April, 2013 and May, 2015 were included in the present study. The patients were randomly divided into group A (lung cancer) and group B (squamous cell lung carcinoma). RT-PCR was used to detect the cancer and adjacent tissues, and Nanog gene expression was detected in groups A and B in cells. The results showed that, analysis of Nanog gene expression in the two groups of patients varied to different degrees. There was no significant difference between the two groups with regard to age, gender, disease stage and lymph node metastasis. Nanog gene expression in patients with carcinoma were significantly higher than that in the adjacent tissues (p<0.05). By contrast, differentiated and well-differentiated carcinoma tissue showed a significantly higher Nanog gene expression than poorly differentiated and undifferentiated carcinoma (p<0.05). The expression of Nanog in normal cells was significantly higher than that in normal lung tissues and benign lesions in lung cancer stem cells. Nanog was highly expressed in CD44+ cells, and Nanog expression in lung cancer stem cells was significantly higher (p<0.05). In conclusion, for groups A (lung cancer) and B (squamous cell lung carcinoma) the Nanog gene expression was significantly higher. The data of the present study show that the patients with stage III and IV lung cancer had a higher Nanog gene expression. In addition, there was a higher expression of Nanog in lung cancer patients. By contrast, a lower degree of cell differentiation was associated with strong Nanog gene expression in lung cancer.

  1. Interactions between sealing materials and lubricating oil additives

    SciTech Connect

    Winkenbach, R.; Von Arndt, E.M.; Mindermann, H.

    1987-01-01

    Due to the increasingly higher application demands, engine and transmission manufactures are today using lubrication oils with more and more additives. The result is that seal materials are being damaged when exposed to such conditions and such additives. This paper shows the effects of basic oils with, and without, additives on elastomeric materials such as NBR, ACM, MVQ and FPM.

  2. Effect of HLB of additives on the properties and drug release from the glyceryl monooleate matrices.

    PubMed

    Shah, Manish H; Paradkar, Anant

    2007-08-01

    Glyceryl monooleate (GMO) is an amphiphilic surfactant, which as such can solubilize hydrophilic, lipophilic and amphiphilic drug molecules in its different polarity regions. Addition of additives with different polarities in GMO leads to change in phase behavior and related properties of GMO. Effect of the additives with different hydrophilic lipophilic balance (HLB; 1.5, 3, 4, 5, 7, 10 and 11) in GMO matrices on its phase transformation, rheological properties, mechanical properties, wetting and release behavior was investigated. Polarizing light microscopy showed that the GMO matrices incorporated with lower HLB additive (1.5, 3, 4 and 5) form cubic phase at higher rate while lamellar phase was prominent for matrices with additive of HLB 7, 10 and 11. The diametrical crushing strength and viscosity was decreased with increased HLB of additive. Lower HLB additives enhanced contact angle as compared to plain matrices and high HLB additives induced change in solid-liquid interface from hydrophobic to hydrophilic leading to decline in contact angle. Percent swelling of matrices was increased linearly with increase in HLB of additives. Tensiometric method was used for determination of bioadhesive strength of hydrated matrices and it was observed that matrices with additives of HLB 10 presented highest bioadhesion due to higher rate of hydration and formation of lamellar phase. As the HLB of additives in matrix increased, release was shifted from anomalous (non-Fickian) diffusion and/or partially erosion-controlled release to Fickian diffusion. Initial lag was observed for drug released from matrices with additive of HLB 1.5, 3, 4 and 5. Thus incorporation of the additives of different HLB changed molecular packing, which significantly affected drug release pattern.

  3. Astronomical Significance of Ancient Monuments

    NASA Astrophysics Data System (ADS)

    Simonia, I.

    2011-06-01

    Astronomical significance of Gokhnari megalithic monument (eastern Georgia) is considered. Possible connection of Amirani ancient legend with Gokhnari monument is discussed. Concepts of starry practicality and solar stations are proposed.

  4. [Forensic significance of depressive syndromes].

    PubMed

    Lammel, M

    1987-10-01

    The three chief problems arising when an expert opinion is to be given are dealt with in brief, and the forensic significance of the depressive syndrome is described, without entering into the question of giving an opinion as to responsibility.

  5. The "New" Performance Funding in Higher Education

    ERIC Educational Resources Information Center

    McKeown-Moak, Mary P.

    2013-01-01

    Over the past several years, public higher education, both in the U.S. and internationally, has increasingly been required to explain, defend, and validate its performance and value to a wide variety of constituents, including governors, legislators, students, parents, employers, and taxpayers. In addition, in 2006, then U.S. Secretary of…

  6. Outsourcing in Higher Education. ERIC Digest.

    ERIC Educational Resources Information Center

    Wood, Patricia A.

    Higher education has increasingly turned to outsourcing to improve service in the face of declining resources. Outsourcing has traditionally been used to operate campus bookstores and dining services and has more recently become a legitimate option for additional campus functions, such as facilities operation, computer services, security, child…

  7. Administrator Job Satisfaction in Higher Education

    ERIC Educational Resources Information Center

    Howard-Baldwin, Tonia; Celik, Bekir; Kraska, Marie

    2012-01-01

    The purpose of the study was to investigate the job satisfaction of men and women administrators in higher education in a four-year university in the southeast. In addition, the study examined whether there was a relationship between gender and overall job satisfaction, work climate, and job structure. Data were collected in the spring of 2009. …

  8. 2011 AGB Survey of Higher Education Governance

    ERIC Educational Resources Information Center

    Association of Governing Boards of Universities and Colleges, 2011

    2011-01-01

    This report, the second of AGB's studies of higher education governance, documents the extent to which college and university boards are following good-governance practices. In addition, it takes a focused look at board engagement to determine the degree to which governing boards are actively, intellectually, and strategically involved with their…

  9. Higher Education: A Bibliographic Handbook, Volume II.

    ERIC Educational Resources Information Center

    Halstead, D. Kent, Ed.

    Higher education topics that pertain to the individual institution are addressed in this annotated bibliography, which primarily covers publications issued during 1968-1980. In addition, introductory descriptions of each topic and outlines of subtopics are provided. The 20 major topics and the compilers for each topic are as follows:…

  10. Higher Education: New Models, New Rules

    ERIC Educational Resources Information Center

    Soares, Louis; Eaton, Judith S.; Smith, Burck

    2013-01-01

    The Internet enables new models. In the commercial world, for example, we have eBay, Amazon.com, and Netflix. These new models operate with a different set of rules than do traditional models. New models are emerging in higher education as well--for example, competency-based programs. In addition, courses that are being provided from outside the…

  11. Optimal Dose of Vitamin D3 400 I.U. for Average Adults has A Significant Anti-Cancer Effect, While Widely Used 2000 I.U. or Higher Promotes Cancer: Marked Reduction of Taurine & 1α, 25(OH)2D3 Was Found In Various Cancer Tissues and Oral Intake of Optimal Dose of Taurine 175mg for Average Adults, Rather Than 500mg, Was Found to Be A New Potentially Safe and More Effective Method of Cancer Treatment.

    PubMed

    Omura, Yoshiaki; Lu, Dominic; Jones, Marilyn K; Nihrane, Abdallah; Duvvi, Harsha; Yapor, Dario; Shimotsuura, Yasuhiro; Ohki, Motomu

    2016-01-01

    During the past 10 years, the author had found that the optimal dose of Vitamin D3 400 I.U. has safe & effective anticancer effects, while commonly used 2000-5000 I.U. of Vit. D3 often creates a 2-3 time increase in cancer markers. We examined the concentration of Taurine in normal internal organs and in cancer using Bi-Digital O-Ring Test. We found that Taurine levels in normal tissue are 4-6ng. But, the amount of Taurine of average normal value of 5.0-5.25ng was strikingly reduced to 0.0025-0.0028ng in this study of several examples in adenocarcinomas of the esophagus, stomach, pancreas, colon, prostate, and lung, as well as breast cancer. The lowest Taurine levels of 0.0002-0.0005ng were found in so called Zika virus infected babies from Brazil with microcephaly. While Vitamin D3 receptor stimulant 1α, 25 (OH)2D3 in normal tissues was 0.45-0.53ng, they were reduced to 0.025-0.006ng in cancers (1/100th-1/200th of normal value), particularly in various adenocarcinomas. All of these adenocarcinomas had about 1500ng HPV-16 viral infection. In 500 breast cancers, about 97% had HPV-16. The optimal dose of Taurine for average adult has been found to be about 175mg, rather than the widely used 500mg. In addition, since Taurine is markedly reduced to close to 1/1000th-1/2000th of its normal value in these cancer tissues, we examined the effect of the optimal dose of Taurine on cancer patients. Optimal dose of Taurine produced a very significant decrease in cancer-associated parameters, such as Oncogene C-fosAb2 & Integrin α5β1 being reduced to less than 1/1,000th, and 8-OH-dG (which increases in the presence of DNA mutation) reduced to less than 1/10th. The optimal dose of Taurine 175mg for average adult various cancer patient 3 times a day alone provide beneficial effects with very significant anti-cancer effects with strikingly increased urinary excretion of bacteria, viruses, & funguses, asbestos, toxic metals & other toxic substances. However, optimal doses of

  12. Optimal Dose of Vitamin D3 400 I.U. for Average Adults has A Significant Anti-Cancer Effect, While Widely Used 2000 I.U. or Higher Promotes Cancer: Marked Reduction of Taurine & 1α, 25(OH)2D3 Was Found In Various Cancer Tissues and Oral Intake of Optimal Dose of Taurine 175mg for Average Adults, Rather Than 500mg, Was Found to Be A New Potentially Safe and More Effective Method of Cancer Treatment.

    PubMed

    Omura, Yoshiaki; Lu, Dominic; Jones, Marilyn K; Nihrane, Abdallah; Duvvi, Harsha; Yapor, Dario; Shimotsuura, Yasuhiro; Ohki, Motomu

    2016-01-01

    During the past 10 years, the author had found that the optimal dose of Vitamin D3 400 I.U. has safe & effective anticancer effects, while commonly used 2000-5000 I.U. of Vit. D3 often creates a 2-3 time increase in cancer markers. We examined the concentration of Taurine in normal internal organs and in cancer using Bi-Digital O-Ring Test. We found that Taurine levels in normal tissue are 4-6ng. But, the amount of Taurine of average normal value of 5.0-5.25ng was strikingly reduced to 0.0025-0.0028ng in this study of several examples in adenocarcinomas of the esophagus, stomach, pancreas, colon, prostate, and lung, as well as breast cancer. The lowest Taurine levels of 0.0002-0.0005ng were found in so called Zika virus infected babies from Brazil with microcephaly. While Vitamin D3 receptor stimulant 1α, 25 (OH)2D3 in normal tissues was 0.45-0.53ng, they were reduced to 0.025-0.006ng in cancers (1/100th-1/200th of normal value), particularly in various adenocarcinomas. All of these adenocarcinomas had about 1500ng HPV-16 viral infection. In 500 breast cancers, about 97% had HPV-16. The optimal dose of Taurine for average adult has been found to be about 175mg, rather than the widely used 500mg. In addition, since Taurine is markedly reduced to close to 1/1000th-1/2000th of its normal value in these cancer tissues, we examined the effect of the optimal dose of Taurine on cancer patients. Optimal dose of Taurine produced a very significant decrease in cancer-associated parameters, such as Oncogene C-fosAb2 & Integrin α5β1 being reduced to less than 1/1,000th, and 8-OH-dG (which increases in the presence of DNA mutation) reduced to less than 1/10th. The optimal dose of Taurine 175mg for average adult various cancer patient 3 times a day alone provide beneficial effects with very significant anti-cancer effects with strikingly increased urinary excretion of bacteria, viruses, & funguses, asbestos, toxic metals & other toxic substances. However, optimal doses of

  13. Statistical Significance vs. Practical Significance: An Exploration through Health Education

    ERIC Educational Resources Information Center

    Rosen, Brittany L.; DeMaria, Andrea L.

    2012-01-01

    The purpose of this paper is to examine the differences between statistical and practical significance, including strengths and criticisms of both methods, as well as provide information surrounding the application of various effect sizes and confidence intervals within health education research. Provided are recommendations, explanations and…

  14. Color Addition and Subtraction Apps

    NASA Astrophysics Data System (ADS)

    Ruiz, Frances; Ruiz, Michael J.

    2015-10-01

    Color addition and subtraction apps in HTML5 have been developed for students as an online hands-on experience so that they can more easily master principles introduced through traditional classroom demonstrations. The evolution of the additive RGB color model is traced through the early IBM color adapters so that students can proceed step by step in understanding mathematical representations of RGB color. Finally, color addition and subtraction are presented for the X11 colors from web design to illustrate yet another real-life application of color mixing.

  15. Anaerobic sludge digestion with a biocatalytic additive

    SciTech Connect

    Ghosh, S.; Henry, M.P.; Fedde, P.A.

    1982-01-01

    The objective of this research was to evaluate the effects of a lactobacillus additive an anaerobic sludge digestion under normal, variable, and overload operating conditions. The additive was a whey fermentation product of an acid-tolerant strain of Lactobacillus acidophilus fortified with CaCO/sub 3/, (NH/sub 4/)/sub 2/HPO/sub 4/, ferrous lactate, and lactic acid. The lactobacillus additive is multifunctional in nature and provides growth factors, metabolic intermediates, and enzymes needed for substrate degradation and cellular synthesis. The experimental work consisted of several pairs of parallel mesophilic (35/sup 0/C) digestion runs (control and test) conducted in five experimental phases. Baseline runs without the additive showed that the two experimental digesters had the same methane content, gas production rate (GPR), and ethane yield. The effect of the additive was to increase methane yield and GPR by about 5% (which was statistically significant) during digester operation at a loading rate (LR) of 3.2 kg VS/m/sup 3/-day and a hydraulic retention time (HRT) of 14 days. Data collected from the various experimental phases showed that the biochemical additive increased methane yield, gas production rate, and VS reduction, and decreased volatile acids accumulation. In addition, it enhanced digester buffer capacity and improved the fertilizer value and dewatering characteristics of the digested residue.

  16. Microbial biosurfactants as additives for food industries.

    PubMed

    Campos, Jenyffer Medeiros; Stamford, Tânia Lúcia Montenegro; Sarubbo, Leonie Asfora; de Luna, Juliana Moura; Rufino, Raquel Diniz; Banat, Ibrahim M

    2013-01-01

    Microbial biosurfactants with high ability to reduce surface and interfacial surface tension and conferring important properties such as emulsification, detergency, solubilization, lubrication and phase dispersion have a wide range of potential applications in many industries. Significant interest in these compounds has been demonstrated by environmental, bioremediation, oil, petroleum, food, beverage, cosmetic and pharmaceutical industries attracted by their low toxicity, biodegradability and sustainable production technologies. Despite having significant potentials associated with emulsion formation, stabilization, antiadhesive and antimicrobial activities, significantly less output and applications have been reported in food industry. This has been exacerbated by uneconomical or uncompetitive costing issues for their production when compared to plant or chemical counterparts. In this review, biosurfactants properties, present uses and potential future applications as food additives acting as thickening, emulsifying, dispersing or stabilising agents in addition to the use of sustainable economic processes utilising agro-industrial wastes as alternative substrates for their production are discussed.

  17. Higher order turbulence closure models

    NASA Technical Reports Server (NTRS)

    Amano, Ryoichi S.; Chai, John C.; Chen, Jau-Der

    1988-01-01

    Theoretical models are developed and numerical studies conducted on various types of flows including both elliptic and parabolic. The purpose of this study is to find better higher order closure models for the computations of complex flows. This report summarizes three new achievements: (1) completion of the Reynolds-stress closure by developing a new pressure-strain correlation; (2) development of a parabolic code to compute jets and wakes; and, (3) application to a flow through a 180 deg turnaround duct by adopting a boundary fitted coordinate system. In the above mentioned models near-wall models are developed for pressure-strain correlation and third-moment, and incorporated into the transport equations. This addition improved the results considerably and is recommended for future computations. A new parabolic code to solve shear flows without coordinate tranformations is developed and incorporated in this study. This code uses the structure of the finite volume method to solve the governing equations implicitly. The code was validated with the experimental results available in the literature.

  18. Chromosomal replicons of higher plants

    SciTech Connect

    Van't Hof, J.

    1987-03-16

    This brief discussion of replicons of higher plants offers a glimpse into the properties of chromosomal DNA replication. It gives evidence that the S phase of unrelated plant species is comprised of temporally ordered replicon families that increase in number with genome size. This orderly process, which assures a normal inheritance of genetic material to recipient daughter cells, is maintained at the level of replicon clusters by two mutually exclusive mechanisms, one involving the rate at which single replicons replicate their allotment of DNA, and another by means of the tempo-pause. The same two mechanisms are used by cells to alter the pattern of chromosomal DNA replication just prior to and during normal development. Both mechanisms are genetically determined and produce genetic effects when disturbed of disrupted by additional non-conforming DNAs. Further insight into how these two mechanisms operate requires more molecular information about the nature of replicons and the factors that govern when a replicon family replicates. Plant material is a rich and ideal source for this information just awaiting exploitation. 63 refs.

  19. Teebi hypertelorism syndrome: additional cases.

    PubMed

    Machado-Paula, Ligiane Alves; Guion-Almeida, Maria Leine

    2003-03-01

    We report on two unrelated Brazilian boys who have craniofacial and digital anomalies resembling those reported with Teebi hypertelorism syndrome. Additional features such as cleft lip and palate, large uvula, atypical chin and abnormal scapulae were observed.

  20. Polyolefins as additives in plastics

    SciTech Connect

    Deanin, R.D.

    1993-12-31

    Polyolefins are not only major commodity plastics - they are also very useful as additives, both in other polyolefins and also in other types of plastics. This review covers ethylene, propylene, butylene and isobutylene polymers, in blends with each other, and as additives to natural rubber, styrene/butadiene rubber, polystyrene, polyvinyl chloride, polymethyl methacrylate, polyphenylene oxide, polycarbonate, thermoplastic polyesters, polyurethanes, polyamides, and mixed automotive plastics recycling.

  1. Response of Dissolved Organic Matter to Warming and Nitrogen Addition

    NASA Astrophysics Data System (ADS)

    Choi, J. H.; Nguyen, H.

    2014-12-01

    Dissolved Organic Matter (DOM) is a ubiquitous mixture of soluble organic components. Since DOM is produced from the terrestrial leachate of various soil types, soil may influence the chemistry and biology of freshwater through the input of leachate and run-off. The increased temperature by climate change could dramatically change the DOM characteristics of soils through enhanced decomposition rate and losses of carbon from soil organic matter. In addition, the increase in the N-deposition affects DOM leaching from soils by changing the carbon cycling and decomposition rate of soil decay. In this study, we conducted growth chamber experiments using two types of soil (wetland and forest) under the conditions of temperature increase and N-deposition in order to investigate how warming and nitrogen addition influence the characteristics of the DOM leaching from different soil types. This leachate controls the quantity and quality of DOM in surface water systems. After 10 months of incubation, the dissolved organic carbon (DOC) concentrations decreased for almost samples in the range of 7.6 to 87.3% (ANOVA, p<0.05). The specific UV absorption (SUVA) values also decreased for almost samples after the first 3 months and then increased gradually afterward in range of 3.3 to 108.4%. Both time and the interaction between time and the temperature had the statistically significant effects on the SUVA values (MANOVA, p<0.05). Humification index (HIX) showed the significant increase trends during the duration of incubation and temperature for almost the samples (ANOVA, p<0.05). Higher decreases in the DOC values and increases in HIX were observed at higher temperatures, whereas the opposite trend was observed for samples with N-addition. The PARAFAC results showed that three fluorescence components: terrestrial humic (C1), microbial humic-like (C2), and protein-like (C3), constituted the fluorescence matrices of soil samples. During the experiment, labile DOM from the soils was

  2. Rotating Black Holes in Higher Dimensions

    NASA Astrophysics Data System (ADS)

    Kleihaus, Burkhard; Kunz, Jutta; Navarro-Lérida, Francisco

    2008-03-01

    The properties of higher-dimensional black holes can differ significantly from those of black holes in four dimensions, since neither the uniqueness theorem, nor the staticity theorem or the topological censorship theorem generalize to higher dimensions. We first discuss black holes of Einstein-Maxwell theory and Einstein-Maxwell-Chern-Simons theory with spherical horizon topology. Here new types of stationary black holes are encountered. We then discuss nonuniform black strings and present evidence for a horizon topology changing transition.

  3. Status and Significance of Credentialing.

    ERIC Educational Resources Information Center

    Musgrave, Dorothea

    1984-01-01

    Discusses the current status, significance, and future of credentialing in the field of environmental health. Also discusses four phases of a Bureau of Health Professions (BHP) Credentialing Program and BHP-funded projects related to their development and implementation. Phases include role delineation, resources development, examination…

  4. Use of Additional Needle Pulses Using Electrical Discharge Machining

    NASA Astrophysics Data System (ADS)

    Schulze, Hans-Peter; Juhr, Henrik; Haas, Rüdiger

    2011-05-01

    The influence exerted by the longer rectangular pulses with additional Needle Pulses. Needle pulses for the spark erosion are the fundamental of the erosion pulses with pulse durations smaller 1 μs and high current-rise-velocity (ramp unit). In this shorter pulse-duration it is possible to use higher current densities; without composition of the thermal-affected zones. The technological advantage is a higher productivity because the higher pulse energy and parallel a better quality of the processing area exist; an additional factor for the higher productivity is the smaller number of back-cuts for the finish quality of the cut.

  5. Clinical and Predictive Significance of Hyponatremia after Aneurysmal Subarachnoid Hemorrhage

    PubMed Central

    Vrsajkov, Vladimir; Javanović, Gordana; Stanisavljević, Snežana; Uvelin, Arsen; Vrsajkov, Jelena Panti

    2012-01-01

    Objective: Hyponatremia after SAH was the object of several studies with conflicting results. The aim of this study was to determine a predictive correlation of hyponatremia with delayed cerebral ischemia (DCI) and poor clinical outcome. Material and Methods: We have used a retrospective hospital chart review of 82 patients with SAH treated from August 2008 to August 2010. Patients were divided into hyponatremia and normonatremia groups. Hyponatremia was defined as serum sodium level <135 mmol/l. Information compared and analyzed included demographics, preoperative neurological status, aneurysm characteristics, postoperative intensive care, duration of stay, DCI and clinical outcome at hospital discharge. P<0.05 was considered significant. Results: Thirty-two patients with SAH (39%) developed hyponatremia. In that group we had a significantly higher WFNS score at admission (p=0.03) and longer duration of stay in intensive care (p=0.001). DCI with transit or definitive deficit included 20 patients (62%) in the hyponatremia group, and 19 patients (38%) in the normonatremia group (p=0.03). Binary enter logistic regression revealed a significant correlation of hyponatremia with DCI (p=0.03) and poor clinical outcome (p=0.001). Conclusion: This result revealed a possible use of hyponatremia as an additional predictor of developing DCI and poor clinical outcome. PMID:25207008

  6. Extension of the standard addition method by blank addition.

    PubMed

    Steliopoulos, Panagiotis

    2015-01-01

    Standard addition involves adding varying amounts of the analyte to sample portions of fixed mass or fixed volume and submitting those portions to the sample preparation procedure. After measuring the final extract solutions, the observed signals are linearly regressed on the spiked amounts. The original unknown amount is estimated by the opposite of the abscissa intercept of the fitted straight line [1]. A limitation of this method is that only data points with abscissa values equal to and greater than zero are available so that there is no information on whether linearity holds below the spiking level zero. An approach to overcome this limitation is introduced.•Standard addition is combined with blank addition.•Blank addition means that defined mixtures of blank matrix and sample material are subjected to sample preparation to give final extract solutions.•Equations are presented to estimate the original unknown amount and to calculate the 1-2α confidence interval about this estimate using the combined data set.

  7. ADDITIVITY ASSESSMENT OF TRIHALOMETHANE MIXTURES BY PROPORTIONAL RESPONSE ADDITION

    EPA Science Inventory

    If additivity is known or assumed, the toxicity of a chemical mixture may be predicted from the dose response curves of the individual chemicals comprising the mixture. As single chemical data are abundant and mixture data sparse, mixture risk methods that utilize single chemical...

  8. Extension of the standard addition method by blank addition

    PubMed Central

    Steliopoulos, Panagiotis

    2015-01-01

    Standard addition involves adding varying amounts of the analyte to sample portions of fixed mass or fixed volume and submitting those portions to the sample preparation procedure. After measuring the final extract solutions, the observed signals are linearly regressed on the spiked amounts. The original unknown amount is estimated by the opposite of the abscissa intercept of the fitted straight line [1]. A limitation of this method is that only data points with abscissa values equal to and greater than zero are available so that there is no information on whether linearity holds below the spiking level zero. An approach to overcome this limitation is introduced.•Standard addition is combined with blank addition.•Blank addition means that defined mixtures of blank matrix and sample material are subjected to sample preparation to give final extract solutions.•Equations are presented to estimate the original unknown amount and to calculate the 1-2α confidence interval about this estimate using the combined data set. PMID:26844210

  9. Predicting the impact of biochar additions on soil hydraulic properties.

    PubMed

    Lim, T J; Spokas, K A; Feyereisen, G; Novak, J M

    2016-01-01

    Different physical and chemical properties of biochar, which is made out of a variety of biomass materials, can impact water movement through amended soil. The objective of this research was to develop a decision support tool predicting the impact of biochar additions on soil saturated hydraulic conductivity (Ksat). Four different kinds of biochar were added to four different textured soils (coarse sand, fine sand, loam, and clay texture) to assess these effects at the rates of 0%, 1%, 2%, and 5% (w/w). The Ksat of the biochar amended soils were significantly influenced by the rate and type of biochar, as well as the original particle size of soil. The Ksat decreased when biochar was added to coarse and fine sands. Biochar with larger particles sizes (60%; >1 mm) decreased Ksat to a larger degree than the smaller particle size biochar (60%; <1 mm) in the two sandy textured soils. Increasing tortuosity in the biochar amended sandy soil could explain this behavior. On the other hand, for the clay loam 1% and 2% biochar additions universally increased the Ksat with higher biochar amounts providing no further alterations. The developed model utilizes soil texture pedotransfer functions for predicting agricultural soil Ksat as a function of soil texture. The model accurately predicted the direction of the Ksat influence, even though the exact magnitude still requires further refinement. This represents the first step to a unified theory behind the impact of biochar additions on soil saturated conductivity. PMID:26145507

  10. Predicting the impact of biochar additions on soil hydraulic properties.

    PubMed

    Lim, T J; Spokas, K A; Feyereisen, G; Novak, J M

    2016-01-01

    Different physical and chemical properties of biochar, which is made out of a variety of biomass materials, can impact water movement through amended soil. The objective of this research was to develop a decision support tool predicting the impact of biochar additions on soil saturated hydraulic conductivity (Ksat). Four different kinds of biochar were added to four different textured soils (coarse sand, fine sand, loam, and clay texture) to assess these effects at the rates of 0%, 1%, 2%, and 5% (w/w). The Ksat of the biochar amended soils were significantly influenced by the rate and type of biochar, as well as the original particle size of soil. The Ksat decreased when biochar was added to coarse and fine sands. Biochar with larger particles sizes (60%; >1 mm) decreased Ksat to a larger degree than the smaller particle size biochar (60%; <1 mm) in the two sandy textured soils. Increasing tortuosity in the biochar amended sandy soil could explain this behavior. On the other hand, for the clay loam 1% and 2% biochar additions universally increased the Ksat with higher biochar amounts providing no further alterations. The developed model utilizes soil texture pedotransfer functions for predicting agricultural soil Ksat as a function of soil texture. The model accurately predicted the direction of the Ksat influence, even though the exact magnitude still requires further refinement. This represents the first step to a unified theory behind the impact of biochar additions on soil saturated conductivity.

  11. [INVITED] Lasers in additive manufacturing

    NASA Astrophysics Data System (ADS)

    Pinkerton, Andrew J.

    2016-04-01

    Additive manufacturing is a topic of considerable ongoing interest, with forecasts predicting it to have major impact on industry in the future. This paper focusses on the current status and potential future development of the technology, with particular reference to the role of lasers within it. It begins by making clear the types and roles of lasers in the different categories of additive manufacturing. This is followed by concise reviews of the economic benefits and disadvantages of the technology, current state of the market and use of additive manufacturing in different industries. Details of these fields are referenced rather than expanded in detail. The paper continues, focusing on current indicators to the future of additive manufacturing. Barriers to its development, trends and opportunities in major industrial sectors, and wider opportunities for its development are covered. Evidence indicates that additive manufacturing may not become the dominant manufacturing technology in all industries, but represents an excellent opportunity for lasers to increase their influence in manufacturing as a whole.

  12. Evaluation of certain food additives.

    PubMed

    2015-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, and to prepare specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives, including flavouring agents. A summary follows of the Committee's evaluations of technical, toxicological and dietary exposure data for eight food additives (Benzoe tonkinensis; carrageenan; citric and fatty acid esters of glycerol; gardenia yellow; lutein esters from Tagetes erecta; octenyl succinic acid-modified gum arabic; octenyl succinic acid-modified starch; paprika extract; and pectin) and eight groups of flavouring agents (aliphatic and alicyclic hydrocarbons; aliphatic and aromatic ethers; ionones and structurally related substances; miscellaneous nitrogen-containing substances; monocyclic and bicyclic secondary alcohols, ketones and related esters; phenol and phenol derivatives; phenyl-substituted aliphatic alcohols and related aldehydes and esters; and sulfur-containing heterocyclic compounds). Specifications for the following food additives were revised: citric acid; gellan gum; polyoxyethylene (20) sorbitan monostearate; potassium aluminium silicate; and Quillaia extract (Type 2). Annexed to the report are tables summarizing the Committee's recommendations for dietary exposures to and toxicological evaluations of all of the food additives and flavouring agents considered at this meeting.

  13. Clinical effects of sulphite additives.

    PubMed

    Vally, H; Misso, N L A; Madan, V

    2009-11-01

    Sulphites are widely used as preservative and antioxidant additives in the food and pharmaceutical industries. Topical, oral or parenteral exposure to sulphites has been reported to induce a range of adverse clinical effects in sensitive individuals, ranging from dermatitis, urticaria, flushing, hypotension, abdominal pain and diarrhoea to life-threatening anaphylactic and asthmatic reactions. Exposure to the sulphites arises mainly from the consumption of foods and drinks that contain these additives; however, exposure may also occur through the use of pharmaceutical products, as well as in occupational settings. While contact sensitivity to sulphite additives in topical medications is increasingly being recognized, skin reactions also occur after ingestion of or parenteral exposure to sulphites. Most studies report a 3-10% prevalence of sulphite sensitivity among asthmatic subjects following ingestion of these additives. However, the severity of these reactions varies, and steroid-dependent asthmatics, those with marked airway hyperresponsiveness, and children with chronic asthma, appear to be at greater risk. In addition to episodic and acute symptoms, sulphites may also contribute to chronic skin and respiratory symptoms. To date, the mechanisms underlying sulphite sensitivity remain unclear, although a number of potential mechanisms have been proposed. Physicians should be aware of the range of clinical manifestations of sulphite sensitivity, as well as the potential sources of exposure. Minor modifications to diet or behaviour lead to excellent clinical outcomes for sulphite-sensitive individuals.

  14. Effect of the Addition of Schisandra chinensis Powder on the Physico-chemical Characteristics of Sausage.

    PubMed

    Jin, S K; Park, J H

    2013-12-01

    The individual and interactive effects of Schisandra chinensis powder (SCP) and sodium nitrite additions on color, pH, water holding capacity, residual nitrite, 2-thiobarbituric acid reactive substances (TBARS), volatile basic nitrogen, texture properties, fatty acids, amino acids and sensory evaluation of cooked pork sausages were investigated after 20 d of storage at 4°C. The powders (0, 0.5 and 1.0%) were added to sausages either alone or in combination with nitrite (0 and 100 ppm). SCP added-sausages showed lower L* (lightness) and W (whiteness) values, and higher b* (yellowness) values than sausage containing no nitrite, and exhibited the highest a(*) values at a 0.5% addition (p<0.05). Residual nitrite and TBARS values were found to be significantly reduced as the addition levels of SCP increased (p<0.05). As the addition of SCP increased, the sausage showed gradually decreased brittleness, cohesiveness, springiness, gumminess and chewiness, while adhesiveness increased. Polyunsaturated fatty acid, n-6 and n-6/n-3 fatty acid ratio concentrations were significantly higher in sausages containing SCP (p<0.05). The addition of SCP to sausage significantly (p<0.05) increased the ammonia content (by 0.5% SCP) and aromatic amino acid concentrations (by 1.0% SCP) (p<0.05). Inclusion of SCP in sausage meat resulted in a significant deterioration in quality characteristics of flavor, springiness, juiciness and overall acceptability (p<0.05). As expected, the observed changes in a*, W, pH, shear force, texture property, TBARS, fatty acid, amino acid and sensory score of sausages, depended on the rate of addition of nitrite (p<0.05). These results suggest that SCP addition is not an effective way of improving the sensory evaluation of sausages, but may beneficially affect TBARS, nitrite scavenging activity, fatty acid and amino acid content in pork sausages.

  15. Effect of the Addition of Schisandra chinensis Powder on the Physico-chemical Characteristics of Sausage

    PubMed Central

    Jin, S. K.; Park, J. H.

    2013-01-01

    The individual and interactive effects of Schisandra chinensis powder (SCP) and sodium nitrite additions on color, pH, water holding capacity, residual nitrite, 2-thiobarbituric acid reactive substances (TBARS), volatile basic nitrogen, texture properties, fatty acids, amino acids and sensory evaluation of cooked pork sausages were investigated after 20 d of storage at 4°C. The powders (0, 0.5 and 1.0%) were added to sausages either alone or in combination with nitrite (0 and 100 ppm). SCP added-sausages showed lower L* (lightness) and W (whiteness) values, and higher b* (yellowness) values than sausage containing no nitrite, and exhibited the highest a* values at a 0.5% addition (p<0.05). Residual nitrite and TBARS values were found to be significantly reduced as the addition levels of SCP increased (p<0.05). As the addition of SCP increased, the sausage showed gradually decreased brittleness, cohesiveness, springiness, gumminess and chewiness, while adhesiveness increased. Polyunsaturated fatty acid, n-6 and n-6/n-3 fatty acid ratio concentrations were significantly higher in sausages containing SCP (p<0.05). The addition of SCP to sausage significantly (p<0.05) increased the ammonia content (by 0.5% SCP) and aromatic amino acid concentrations (by 1.0% SCP) (p<0.05). Inclusion of SCP in sausage meat resulted in a significant deterioration in quality characteristics of flavor, springiness, juiciness and overall acceptability (p<0.05). As expected, the observed changes in a*, W, pH, shear force, texture property, TBARS, fatty acid, amino acid and sensory score of sausages, depended on the rate of addition of nitrite (p<0.05). These results suggest that SCP addition is not an effective way of improving the sensory evaluation of sausages, but may beneficially affect TBARS, nitrite scavenging activity, fatty acid and amino acid content in pork sausages. PMID:25049766

  16. Synergistic Effects Between Phosphonium-Alkylphosphate Ionic Liquids and Zinc Dialkyldithiophosphate (ZDDP) as Lubricant Additives

    DOE PAGES

    Qu, Jun; Barnhill, William C.; Luo, Huimin; Meyer, III, Harry M.; Leonard, Donovan N.; Landauer, Alexander K.; Kheireddin, Bassem; Gao, Hong; Papke, Brian L; Dai, Sheng

    2015-07-14

    Unique synergistic effects between phosphonium-alkylphosphate ionic liquids and zinc dialkyldithiophosphate (ZDDP) are discovered when used together as lubricant additives, resulting in significant friction and wear reduction along with distinct tribofilm composition and mechanical properties. The synergism is attributed to the 30-70× higher-than-nominal concentrations of hypothetical new compounds (via anion exchange between IL and ZDDP) on the fluid surface/interface.

  17. Estimating classification images with generalized linear and additive models.

    PubMed

    Knoblauch, Kenneth; Maloney, Laurence T

    2008-12-22

    Conventional approaches to modeling classification image data can be described in terms of a standard linear model (LM). We show how the problem can be characterized as a Generalized Linear Model (GLM) with a Bernoulli distribution. We demonstrate via simulation that this approach is more accurate in estimating the underlying template in the absence of internal noise. With increasing internal noise, however, the advantage of the GLM over the LM decreases and GLM is no more accurate than LM. We then introduce the Generalized Additive Model (GAM), an extension of GLM that can be used to estimate smooth classification images adaptively. We show that this approach is more robust to the presence of internal noise, and finally, we demonstrate that GAM is readily adapted to estimation of higher order (nonlinear) classification images and to testing their significance.

  18. Additive Manufacturing of Hybrid Circuits

    NASA Astrophysics Data System (ADS)

    Sarobol, Pylin; Cook, Adam; Clem, Paul G.; Keicher, David; Hirschfeld, Deidre; Hall, Aaron C.; Bell, Nelson S.

    2016-07-01

    There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects. Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. Finally, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.

  19. Postmarketing surveillance of food additives.

    PubMed

    Butchko, H H; Tschanz, C; Kotsonis, F N

    1994-08-01

    Postmarketing surveillance of consumption and of anecdotal reports of adverse health effects has been recognized by a number of regulatory authorities as a potentially useful method to provide further assurance of the safety of new food additives. Surveillance of consumption is used to estimate more reliably actual consumption levels relative to the acceptable daily intake of a food additive. Surveillance of anecdotal reports of adverse health effects is used to determine the presence of infrequent idiosyncratic responses that may not be predictable from premarket evaluations. The high-intensity sweetner, aspartame, is a food additive that has been the subject of extensive evaluation during the postmarketing period and is thus used as an example to discuss postmarketing surveillance.

  20. Evolution of the Significant Figure Rules

    NASA Astrophysics Data System (ADS)

    Carter, Ashley R.

    2013-09-01

    Today, almost all introductory physics textbooks include standardized "rules" on how to find the number of significant figures in a calculated value. And yet, 30 years ago these rules were almost nonexistent. Whyhave we increased the role of significant figures in introductory classes, and should we continue this trend? A look back at the evolution of significant figures over the last 300 years, from Newton to Millikan to modern authors, sheds some light on their purpose moving forward. While there is much discussion for and against their use, especially in chemistry, a review of earlier versions of the rules suggests that we have lost some items of value, most notably, a significant figure rule for angles. In addition, we have lost the emphasis that the significant figure rules were designed to calculate an approximate (not exact) precision. Now that the significant figure rules are ingrained into our introductory physics sequence, we would be wise to reiterate that these are just general "rules of thumb."

  1. [Paradigm shift in higher education].

    PubMed

    Csóka, Mária

    2009-08-30

    The fast changes that took place in the last quarter of the 20th century made the professionals dealing with pedagogy realize that our school system followed the economical changes in terms of training supply and the matter of education very slowly, if at all; let alone the educational methods. We had to realize that the maintaining of this conservative system is not rational, education has become the most important part of the globalisational competition and the key to the 21st century is learning. Accordingly, the spatial and temporal expenditure of education has become a new trend, namely lifelong learning (LLL). The social needs on education have increased, the expectations of economy and employers have changed: knowledge has become the fund of competitiveness. In this process, universities have got an accentuated role: in addition to being the place of undergraduate training they have become the site of postgraduate courses for the increasing graduate adult masses. Therefore, reform processes have started in a number of European countries in the nineties. The Bologna Declaration signed on 19th June 1999 set a common direction for these reforms, with its signatories aiming to establish a standard European Higher Education Area with harmonized and comparable educational systems by 2010. However, the administrative change itself is not enough to reach the goals; a formal innovation has to be followed by a reform of the contents which means reformation of higher education. In recent years, Hungarian colleges and universities have worked out their educational programs that are suitable for the new structure; it is only the new educational programs that started from 1st September 2006. The author determines the most important parts of the reform of the training system of Semmelweis University Faculty of Health Sciences, which are the following: redrawing of the training philosophy and paradigm, the reform of the training structure of macro level (cognition

  2. [Paradigm shift in higher education].

    PubMed

    Csóka, Mária

    2009-08-30

    The fast changes that took place in the last quarter of the 20th century made the professionals dealing with pedagogy realize that our school system followed the economical changes in terms of training supply and the matter of education very slowly, if at all; let alone the educational methods. We had to realize that the maintaining of this conservative system is not rational, education has become the most important part of the globalisational competition and the key to the 21st century is learning. Accordingly, the spatial and temporal expenditure of education has become a new trend, namely lifelong learning (LLL). The social needs on education have increased, the expectations of economy and employers have changed: knowledge has become the fund of competitiveness. In this process, universities have got an accentuated role: in addition to being the place of undergraduate training they have become the site of postgraduate courses for the increasing graduate adult masses. Therefore, reform processes have started in a number of European countries in the nineties. The Bologna Declaration signed on 19th June 1999 set a common direction for these reforms, with its signatories aiming to establish a standard European Higher Education Area with harmonized and comparable educational systems by 2010. However, the administrative change itself is not enough to reach the goals; a formal innovation has to be followed by a reform of the contents which means reformation of higher education. In recent years, Hungarian colleges and universities have worked out their educational programs that are suitable for the new structure; it is only the new educational programs that started from 1st September 2006. The author determines the most important parts of the reform of the training system of Semmelweis University Faculty of Health Sciences, which are the following: redrawing of the training philosophy and paradigm, the reform of the training structure of macro level (cognition

  3. Response of bacterial community structure and function to experimental rainwater additions in a coastal eutrophic embayment

    NASA Astrophysics Data System (ADS)

    Teira, Eva; Hernando-Morales, Víctor; Martínez-García, Sandra; Figueiras, Francisco G.; Arbones, Belén; Álvarez-Salgado, Xosé Antón

    2013-03-01

    Although recognized as a potentially important source of both inorganic and organic nutrients, the impact of rainwater on microbial populations from marine planktonic systems has been poorly assessed. The effect of rainwater additions on bacterioplankton metabolism and community composition was evaluated in microcosm experiments enclosing natural marine plankton populations from the Ría de Vigo (NW Spain). The experiments were conducted during three different seasons (spring, autumn and winter) using rainwater collected at three different locations: marine, urban and rural sites. Bacterial abundance and production significantly increased up to 1.3 and 1.8-fold, respectively, after urban rainwater additions in spring, when ambient nutrient concentration was very low. Overall, the increments in bacterial production were higher than those in bacterial respiration, which implies that a higher proportion of carbon consumed by bacteria would be available to higher trophic levels. The response of the different bacterial groups to distinct rainwater types differed between seasons. The most responsive bacterial groups were Betaproteobacteria which significantly increased their abundance after urban (in spring and winter) and marine (in spring) rainwater additions, and Bacteroidetes which positively responded to all rainwater treatments in spring and to urban rainwater in autumn. Gammaproteobacteria and Roseobacter responded only to urban (in spring) and marine (in winter) rainwater treatment, respectively. The responses to rainwater additions were moderate and transient, and the resulting bacterial community structure was not importantly altered.

  4. State Intervention in Higher Education.

    ERIC Educational Resources Information Center

    Glenny, Lyman A.; Bowen, Frank M.

    State intervention in higher education is discussed, and state and federal regulations that affect higher education are discussed and contrasted. The structures and procedures by which states intervene in higher education are outlined, and the issue of institutional autonomy is considered. Policy areas through which the state can affect higher…

  5. Advancing Diversity in Higher Education

    ERIC Educational Resources Information Center

    Turner, Caroline S.

    2013-01-01

    This special section of the "Journal of Diversity in Higher Education" ("JDHE") on "Advancing Diversity in Higher Education" emerged from the 2012 Association for the Study of Higher Education Council on Ethnic Participation (ASHE-CEP) Pre-Conference Forum. CEP, a standing committee of ASHE, partnered with the…

  6. Capital Formation in Higher Education.

    ERIC Educational Resources Information Center

    Frances, Carol; Coldren, Sharon L.

    The need for new capital in higher education and major areas where the interests of the business and higher education communities are aligned are considered. Higher education is a major employer and makes a large contribution to the gross national product. Human capital has become the accepted term for referring to the contribution of education,…

  7. Higher Education Finance Manual 1975.

    ERIC Educational Resources Information Center

    Collier, Douglas J.; Mertins, Paul J.

    The Higher Education Finance Manual (HEFM) is intended to serve as a guide to higher education planners and managers in their understanding and use of institutional finance data. It addresses higher education finance data from the layman's perspective. The document includes definitions of accounting terms and descriptions of generally accepted…

  8. A Tax for Higher Education

    ERIC Educational Resources Information Center

    Blumenstyk, Goldie

    2012-01-01

    Higher education pays off handsomely for society. Yet on a nationwide basis, states' support for higher education per full-time-equivalent student has fallen to just $6,290, the lowest in 15 years. A dedicated source of funds for higher education is problematic. But what if state and federal lawmakers applied the impeccable logic of the gas tax to…

  9. Internationalization of Chinese Higher Education

    ERIC Educational Resources Information Center

    Chen, Linhan; Huang, Danyan

    2013-01-01

    This paper probes into the development of internationalization of higher education in China from ancient times to modern times, including the emergence of international connections in Chinese higher education and the subsequent development of such connections, the further development of internationalization of Chinese higher education, and the…

  10. Commitment to Higher Vocational Education.

    ERIC Educational Resources Information Center

    Imrie, Brad; And Others

    This publication is a history of the College of Higher Vocational Studies (CHVS) since it was established in 1991 and provides commentary on developments in higher vocational education in Hong Kong during a period of unprecedented change and development in the provision of the Higher Diploma. "Principal's Diary" (Bradford Imrie) describes the…

  11. Higher Education Studies in Japan

    ERIC Educational Resources Information Center

    Kaneko, Motohisa

    2010-01-01

    The rapid development of higher education in the postwar period has given rise to various problems, and higher education studies in Japan have developed in response to them. What have been the major issues, and how did academic research respond to them, in postwar Japan? This article delineates an outline of higher education studies in general,…

  12. Higher Education and Public Good

    ERIC Educational Resources Information Center

    Marginson, Simon

    2011-01-01

    Policy debate about whether to maintain public subsidies for higher education has stimulated reconsideration of the public mission of higher education institutions, especially those that provide student places conferring private benefits. If the work of higher education institutions is defined simply as the aggregation of private interests, this…

  13. People Who Study Higher Education

    ERIC Educational Resources Information Center

    Harland, Tony

    2009-01-01

    The study of higher education can seem extraordinarily complex because what counts as knowledge is contestable and the higher education research community is, like Hemingway's Paris, a moveable feast. A lack of epistemological precision and field uncertainty is partly due to the fact that those who study higher education tend to work in higher…

  14. Emerging Trends in Higher Education.

    ERIC Educational Resources Information Center

    Fife, Jonathan D.; Barnett, Lynn

    Trends and projections for higher education are identified. Increased public concern about the purposes and standards of higher education has followed the publication of four major publications about higher education in the United States. Changing demographics are projected for 1983-1993, including fewer 18- to 22-year-olds, decreased full-time…

  15. Higher Education in the Eighties.

    ERIC Educational Resources Information Center

    McComas, James D.

    Events and conditions over the last 20 years that have altered the course of higher education are briefly noted, and trends in higher education for the early eighties are examined. Among the past influences on higher education that illustrate the wisdom of planning for a realistic period of time, such as five years, are the following: the massive…

  16. History of Higher Education, 1992.

    ERIC Educational Resources Information Center

    History of Higher Education, 1992

    1992-01-01

    This annual compilation offers six articles on the history of higher education. In the first article, "The Historical Matrix of American Higher Education," Roger L. Geiger provides an overview of the history of American higher education. Following it, E. D. Duryea, Jurgen Herbst, and W. Bruce Leslie comment on his hypothesis which identifies eight…

  17. Aspects of Higher Spin Symmetry and its Breaking

    NASA Astrophysics Data System (ADS)

    Zhiboedov, Alexander

    . Applications include the 3d Ising model, theories with a gravity dual, SCFTs, and patterns of higher spin symmetry breaking. In chapter 5, we consider higher derivative corrections to the graviton three-point coupling within a weakly coupled theory of gravity. We devise a thought experiment involving a high energy scattering process which leads to causality violation if the graviton three-point vertex contains the additional structures. This violation cannot be fixed by adding conventional particles with spins J ≤ 2. But, it can be fixed by adding an infinite tower of extra massive particles with higher spins, J > 2. In AdS theories this implies a constraint on the conformal anomaly coefficients (a-c)/c lesssim 1/Delta gap2 in terms of Deltagap, the dimension of the lightest single particle operator with spin J > 2. For inflation, or de Sitter-like solutions, it indicates the existence of massive higher spin particles if the gravity wave non-gaussianity deviates significantly from the one computed in the Einstein theory.

  18. Behaviors of Polymer Additives Under EHL and Influences of Interactions Between Additives on Friction Modification

    NASA Technical Reports Server (NTRS)

    Sakurai, T.

    1984-01-01

    Polymer additives have become requisite for the formulation of multigrade engine oils. The behavior of polymethacrylate (PMA)-thickened oils as lubricants in concentrated contacts under nominal rolling and pure sliding conditions was investigated by conventional optical interferometry. The PMA thickened oils behaved differently from the base oil in the formation of elastohydrodynamic (EHL) films. The higher the elastohydrodynamic molecular weight of the PMA contained in the lubricant, the thinner was the oil film under EHL conditions. The film thickness of shear-degraded PMA-thickened oils was also investigated. The behavior of graphite particles dispersed in both the base oil and the PMA-thickened oil was studied under pure sliding by taking photomicrographs. Many kinds of additives are contained in lubricating oil and the interactions between additives are considered. The interactions of zinc-organodithiophosphates (ZDP) with other additives is discussed.

  19. Additive manufacturing of polymer-derived ceramics.

    PubMed

    Eckel, Zak C; Zhou, Chaoyin; Martin, John H; Jacobsen, Alan J; Carter, William B; Schaedler, Tobias A

    2016-01-01

    The extremely high melting point of many ceramics adds challenges to additive manufacturing as compared with metals and polymers. Because ceramics cannot be cast or machined easily, three-dimensional (3D) printing enables a big leap in geometrical flexibility. We report preceramic monomers that are cured with ultraviolet light in a stereolithography 3D printer or through a patterned mask, forming 3D polymer structures that can have complex shape and cellular architecture. These polymer structures can be pyrolyzed to a ceramic with uniform shrinkage and virtually no porosity. Silicon oxycarbide microlattice and honeycomb cellular materials fabricated with this approach exhibit higher strength than ceramic foams of similar density. Additive manufacturing of such materials is of interest for propulsion components, thermal protection systems, porous burners, microelectromechanical systems, and electronic device packaging.

  20. Additive manufacturing of polymer-derived ceramics.

    PubMed

    Eckel, Zak C; Zhou, Chaoyin; Martin, John H; Jacobsen, Alan J; Carter, William B; Schaedler, Tobias A

    2016-01-01

    The extremely high melting point of many ceramics adds challenges to additive manufacturing as compared with metals and polymers. Because ceramics cannot be cast or machined easily, three-dimensional (3D) printing enables a big leap in geometrical flexibility. We report preceramic monomers that are cured with ultraviolet light in a stereolithography 3D printer or through a patterned mask, forming 3D polymer structures that can have complex shape and cellular architecture. These polymer structures can be pyrolyzed to a ceramic with uniform shrinkage and virtually no porosity. Silicon oxycarbide microlattice and honeycomb cellular materials fabricated with this approach exhibit higher strength than ceramic foams of similar density. Additive manufacturing of such materials is of interest for propulsion components, thermal protection systems, porous burners, microelectromechanical systems, and electronic device packaging. PMID:26721993

  1. Additive manufacturing of polymer-derived ceramics

    NASA Astrophysics Data System (ADS)

    Eckel, Zak C.; Zhou, Chaoyin; Martin, John H.; Jacobsen, Alan J.; Carter, William B.; Schaedler, Tobias A.

    2016-01-01

    The extremely high melting point of many ceramics adds challenges to additive manufacturing as compared with metals and polymers. Because ceramics cannot be cast or machined easily, three-dimensional (3D) printing enables a big leap in geometrical flexibility. We report preceramic monomers that are cured with ultraviolet light in a stereolithography 3D printer or through a patterned mask, forming 3D polymer structures that can have complex shape and cellular architecture. These polymer structures can be pyrolyzed to a ceramic with uniform shrinkage and virtually no porosity. Silicon oxycarbide microlattice and honeycomb cellular materials fabricated with this approach exhibit higher strength than ceramic foams of similar density. Additive manufacturing of such materials is of interest for propulsion components, thermal protection systems, porous burners, microelectromechanical systems, and electronic device packaging.

  2. Sixteen-Day Bedrest Significantly Increases Plasma Colloid Osmotic Pressure

    NASA Technical Reports Server (NTRS)

    Hargens, Alan R.; Hsieh, S. T.; Murthy, G.; Ballard, R. E.; Convertino, V. A.; Wade, Charles E. (Technical Monitor)

    1994-01-01

    Upon exposure to microgravity, astronauts lose up to 10% of their total plasma volume, which may contribute to orthostatic intolerance after space flight. Because plasma colloid osmotic pressure (COP) is a primary factor maintaining plasma volume, our objective was to measure time course changes in COP during microgravity simulated by 6 deg. head-down tilt (HDT). Seven healthy male subjects (30-55 years of age) were placed in HDT for 16 days. For the purpose of another study, three of the seven subjects were chosen to exercise on a cycle ergometer on day 16. Blood samples were drawn immediately before bedrest on day 14 of bedrest, 18-24 hours following exercise while all subjects were still in HDT and 1 hour following bedrest termination. Plasma COP was measured in all 20 microliter EDTA-treated samples using an osmometer fitted with a PM 30 membrane. Data were analyzed with paired and unpaired t-tests. Plasma COP on day 14 of bedrest (29.9 +/- 0.69 mmHg) was significantly higher (p less than 0.005) than the control, pre-bedrest value (23.1 +/- 0.76 mmHg). At one hour of upright recovery after HDT, plasma COP remained significantly elevated (exercise: 26.9 +/- 0.87 mmHg; no exercise: 26.3 +/- 0.85 mmHg). Additionally, exercise had no significant effect on plasma COP 18-24 hours following exercise (exercise: 27.8 +/- 1.09 mmHg; no exercise: 27.1 +/- 0.78 mmHg). Our results demonstrate that plasma COP increases significantly with microgravity simulated by HDT. However, preliminary results indicate exercise during HDT does not significantly affect plasma COP.

  3. Lubricating additive for drilling muds

    SciTech Connect

    Gutierrez, A.; Brois, S. J.; Brownawell, D. W.; Walker, T. O.

    1985-01-01

    Aqueous drilling fluids containing a minor amount of an additive composition featuring oxazolines of C/sub 1/-C/sub 30/ alkylthioglycolic acid. Such fluids are especially useful where reduced torque drilling fluids are needed. Another embodiment of this invention relates to a method of drilling utilizing the above-described fluids.

  4. Tetrasulfide extreme pressure lubricant additives

    SciTech Connect

    Gast, L.E.; Kenney, H.E.; Schwab, A.W.

    1980-08-19

    A novel class of compounds has been prepared comprising the tetrasulfides of /sup 18/C hydrocarbons, /sup 18/C fatty acids, and /sup 18/C fatty and alkyl and triglyceride esters. These tetrasulfides are useful as extreme pressure lubricant additives and show potential as replacements for sulfurized sperm whale oil.

  5. Promoting Additive Acculturation in Schools.

    ERIC Educational Resources Information Center

    Gibson, Margaret A.

    1995-01-01

    A study focusing on 113 ninth graders of Mexican descent indicates that most students and their parents adhere to a strategy of additive acculturation (incorporating skills of the new culture and language), but that the school curriculum and general school climate devalue Mexican culture. (SLD)

  6. Individualized Additional Instruction for Calculus

    ERIC Educational Resources Information Center

    Takata, Ken

    2010-01-01

    College students enrolling in the calculus sequence have a wide variance in their preparation and abilities, yet they are usually taught from the same lecture. We describe another pedagogical model of Individualized Additional Instruction (IAI) that assesses each student frequently and prescribes further instruction and homework based on the…

  7. Out of bounds additive manufacturing

    DOE PAGES

    Holshouser, Chris; Newell, Clint; Palas, Sid; Love, Lonnie J.; Kunc, Vlastimil; Lind, Randall F.; Lloyd, Peter D.; Rowe, John C.; Blue, Craig A.; Duty, Chad E.; et al

    2013-03-01

    Lockheed Martin and Oak Ridge National Laboratory are working on an additive manufacturing system capable of manufacturing components measured not in terms of inches or feet, but multiple yards in all dimensions with the potential to manufacture parts that are completely unbounded in size.

  8. Tinkertoy Color-Addition Device.

    ERIC Educational Resources Information Center

    Ferguson, Joe L.

    1995-01-01

    Describes construction and use of a simple home-built device, using an overhead projector, for use in demonstrations of the addition of various combinations of red, green, and blue light. Useful in connection with discussions of color, color vision, or color television. (JRH)

  9. Additional Financial Resources for Education.

    ERIC Educational Resources Information Center

    Hubbard, Ben C.

    This paper discusses the continuing need for additional educational funds and suggests that the only way to gain these funds is through concerted and persistent political efforts by supporters of education at both the federal and state levels. The author first points out that for many reasons declining enrollment may not decrease operating costs…

  10. Higher-order force gradient symplectic algorithms

    NASA Astrophysics Data System (ADS)

    Chin, Siu A.; Kidwell, Donald W.

    2000-12-01

    We show that a recently discovered fourth order symplectic algorithm, which requires one evaluation of force gradient in addition to three evaluations of the force, when iterated to higher order, yielded algorithms that are far superior to similarly iterated higher order algorithms based on the standard Forest-Ruth algorithm. We gauge the accuracy of each algorithm by comparing the step-size independent error functions associated with energy conservation and the rotation of the Laplace-Runge-Lenz vector when solving a highly eccentric Kepler problem. For orders 6, 8, 10, and 12, the new algorithms are approximately a factor of 103, 104, 104, and 105 better.

  11. Breastfeeding twins and higher-order multiples.

    PubMed

    Gromada, K K; Spangler, A K

    1998-01-01

    The benefits of breastfeeding for pre-term and full-term infants are well documented. Breastfeeding facilitates maternal-infant attachment, provides optimal infant nutrition and immunologic protection, and minimizes economic impact. These benefits are multiplied with twins and higher-order multiples, who often are born at risk. Supporting a mother as she initiates and continues to breastfeed one infant requires specific knowledge and skills. Health professionals need additional knowledge and skills if they are to provide appropriate assessment, intervention, and support when a mother breastfeeds twins or higher-order multiples.

  12. Breastfeeding twins and higher-order multiples.

    PubMed

    Gromada, K K; Spangler, A K

    1998-01-01

    The benefits of breastfeeding for pre-term and full-term infants are well documented. Breastfeeding facilitates maternal-infant attachment, provides optimal infant nutrition and immunologic protection, and minimizes economic impact. These benefits are multiplied with twins and higher-order multiples, who often are born at risk. Supporting a mother as she initiates and continues to breastfeed one infant requires specific knowledge and skills. Health professionals need additional knowledge and skills if they are to provide appropriate assessment, intervention, and support when a mother breastfeeds twins or higher-order multiples. PMID:9684207

  13. Evaluation of certain food additives.

    PubMed

    2012-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to concluding as to safety concerns and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives, including flavouring agents. A summary follows of the Committee's evaluations of technical, toxicological and dietary exposure data for five food additives (magnesium dihydrogen diphosphate; mineral oil (medium and low viscosity) classes II and III; 3-phytase from Aspergillus niger expressed in Aspergillus niger; serine protease (chymotrypsin) from Nocardiopsis prasina expressed in Bacillus licheniformis; and serine protease (trypsin) from Fusarium oxysporum expressed in Fusarium venenatum) and 16 groups of flavouring agents (aliphatic and aromatic amines and amides; aliphatic and aromatic ethers; aliphatic hydrocarbons, alcohols, aldehydes, ketones, carboxylic acids and related esters, sulfides, disulfides and ethers containing furan substitution; aliphatic linear alpha,beta-unsaturated aldehydes, acids and related alcohols, acetals and esters; amino acids and related substances; epoxides; furfuryl alcohol and related substances; linear and branched-chain aliphatic, unsaturated, unconjugated alcohols, aldehydes, acids and related esters; miscellaneous nitrogen-containing substances; phenol and phenol derivatives; pyrazine derivatives; pyridine, pyrrole and quinoline derivatives; saturated aliphatic acyclic branched-chain primary alcohols, aldehydes and acids; simple aliphatic and aromatic sulfides and thiols; sulfur-containing heterocyclic compounds; and sulfur-substituted furan derivatives). Specifications for the following food additives were revised: ethyl cellulose, mineral oil (medium viscosity), modified starches and titanium

  14. Evaluation of certain food additives.

    PubMed

    2012-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to concluding as to safety concerns and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives, including flavouring agents. A summary follows of the Committee's evaluations of technical, toxicological and dietary exposure data for five food additives (magnesium dihydrogen diphosphate; mineral oil (medium and low viscosity) classes II and III; 3-phytase from Aspergillus niger expressed in Aspergillus niger; serine protease (chymotrypsin) from Nocardiopsis prasina expressed in Bacillus licheniformis; and serine protease (trypsin) from Fusarium oxysporum expressed in Fusarium venenatum) and 16 groups of flavouring agents (aliphatic and aromatic amines and amides; aliphatic and aromatic ethers; aliphatic hydrocarbons, alcohols, aldehydes, ketones, carboxylic acids and related esters, sulfides, disulfides and ethers containing furan substitution; aliphatic linear alpha,beta-unsaturated aldehydes, acids and related alcohols, acetals and esters; amino acids and related substances; epoxides; furfuryl alcohol and related substances; linear and branched-chain aliphatic, unsaturated, unconjugated alcohols, aldehydes, acids and related esters; miscellaneous nitrogen-containing substances; phenol and phenol derivatives; pyrazine derivatives; pyridine, pyrrole and quinoline derivatives; saturated aliphatic acyclic branched-chain primary alcohols, aldehydes and acids; simple aliphatic and aromatic sulfides and thiols; sulfur-containing heterocyclic compounds; and sulfur-substituted furan derivatives). Specifications for the following food additives were revised: ethyl cellulose, mineral oil (medium viscosity), modified starches and titanium

  15. The Nature of Work and the Stress of Higher Status

    ERIC Educational Resources Information Center

    Schieman, Scott; Whitestone, Yuko Kurashina; Van Gundy, Karen

    2006-01-01

    Are occupational and work conditions associated with work-to-home conflict? If so, do those associations vary by gender? Among a sample of adults in Toronto, Canada, we found that men and women in higher-status occupations reported higher levels of work-to-home conflict than workers in lower-status jobs. In addition, we observed higher levels of…

  16. Significance of biofilms in dentistry.

    PubMed

    Wróblewska, Marta; Strużycka, Izabela; Mierzwińska-Nastalska, Elżbieta

    2015-01-01

    In the past decades significant scientific progress has taken place in the knowledge about biofilms. They constitute multilayer conglomerates of bacteria and fungi, surrounded by carbohydrates which they produce, as well as substances derived from saliva and gingival fluid. Modern techniques showed significant diversity of the biofilm environment and a system of microbial communication (quorum sensing), enhancing their survival. At present it is believed that the majority of infections, particularly chronic with exacerbations, are a result of biofilm formation, particularly in the presence of biomaterials. It should be emphasised that penetration of antibiotics and other antimicrobial agents into deeper layers of a biofilm is poor, causing therapeutic problems and necessitating sometimes removal of the implant or prosthesis. Biofilms play an increasing role in dentistry as a result of more and more broad use in dental practice of plastic and implantable materials. Biofilms are produced on the surfaces of teeth as dental plaque, in the para-nasal sinuses, on prostheses, dental implants, as well as in waterlines of a dental unit, constituting a particular risk for severely immunocompromised patients. New methods of therapy and prevention of infections linked to biofilms are under development.

  17. Patterns of Governance in Higher Education Concepts and Trends. New Papers on Higher Education: Studies and Research 9.

    ERIC Educational Resources Information Center

    van Vught, Frans

    This paper presents a review of the literature on governance and management of higher education, offers a set of concepts for discussion on higher education governance, and identifies recent trends that might have a significant influence on the development of higher education systems. It examines the dynamics of higher education systems, focusing…

  18. [Malassezia yeasts and their significance in dermatology].

    PubMed

    Hort, W; Nilles, M; Mayser, P

    2006-07-01

    Yeasts of the genus Malassezia belong to the normal microflora of the human skin. In addition they are known to cause a variety of skin diseases; the most frequent of which is pityriasis versicolor. Malassezia yeasts are also thought to be associated with seborrheic dermatitis, dandruff and Malassezia folliculitis. Recently the significance of Malassezia yeasts as a trigger factor for atopic dermatitis of the head and neck region has been pointed out. The role of the Malassezia yeasts in these different diseases has been controversial in the past and remains an issue because of difficulties in isolation, culture and differentiation of the organism. Thanks to molecular techniques, 10 species can actually be differentiated. The article presents the different Malassezia-associated diseases, their clinical picture, diagnosis and appropriate therapy. In addition the speciation of Malassezia is reviewed. PMID:16758222

  19. Materials as additives for advanced lubrication

    DOEpatents

    Pol, Vilas G.; Thackeray, Michael M.; Mistry, Kuldeep; Erdemir, Ali

    2016-09-13

    This invention relates to carbon-based materials as anti-friction and anti-wear additives for advanced lubrication purposes. The materials comprise carbon nanotubes suspended in a liquid hydrocarbon carrier. Optionally, the compositions further comprise a surfactant (e.g., to aid in dispersion of the carbon particles). Specifically, the novel lubricants have the ability to significantly lower friction and wear, which translates into improved fuel economies and longer durability of mechanical devices and engines.

  20. Additional renal arteries: incidence and morphometry.

    PubMed

    Satyapal, K S; Haffejee, A A; Singh, B; Ramsaroop, L; Robbs, J V; Kalideen, J M

    2001-01-01

    Advances in surgical and uro-radiological techniques dictate a reappraisal and definition of renal arterial variations. This retrospective study aimed at establishing the incidence of additional renal arteries. Two subsets were analysed viz.: a) Clinical series--130 renal angiograms performed on renal transplant donors, 32 cadaver kidneys used in renal transplantation b) Cadaveric series--74 en-bloc morphologically normal kidney pairs. The sex and race distribution was: males 140, females 96; African 84, Indian 91, White 43 and "Coloured" 18, respectively. Incidence of first and second additional arteries were respectively, 23.2% (R: 18.6%; L: 27.6%) and 4.5% (R: 4.7%; L: 4.4%). Additional arteries occurred more frequently on the left (L: 32.0%; R: 23.3%). The incidence bilaterally was 10.2% (first additional arteries, only). The sex and race incidence (first and second additional) was: males, 28.0%, 5.1%; females, 16.4%, 3.8% and African 31.1%, 5.4%; Indian 13.5%, 4.5%; White 30.9%, 4.4% and "Coloured" 18.5%, 0%; respectively. Significant differences in the incidence of first additional arteries were noted between sex and race. The morphometry of additional renal arteries were lengths (cm) of first and second additional renal arteries: 4.5 and 3.8 (right), 4.9 and 3.7 (left); diameters: 0.4 and 0.3 (right), 0.3 and 0.3 (left). Detailed morphometry of sex and race were also recorded. No statistically significant differences were noted. Our results of the incidence of additional renal arteries of 27.7% compared favourably to that reported in the literature (weighted mean 28.1%). The study is unique in recording detailed morphometry of these vessels. Careful techniques in the identification of this anatomical variation is important since it impacts on renal transplantation surgery, vascular operations for renal artery stenosis, reno-vascular hypertension, Takayasu's disease, renal trauma and uro-radiological procedures.

  1. Higher: Setting a Higher Bar for Higher Ed. 2013 Annual Report

    ERIC Educational Resources Information Center

    American Council of Trustees and Alumni, 2014

    2014-01-01

    The American Council of Trustees and Alumni (ACTA) is leading the charge to return "higher" to higher education. We are challenging the status quo to restore academic freedom, academic rigor, and real accountability to higher education. And, we are doing so with an ever-widening network of supporters and partners.

  2. The impact of additional malignancies in patients diagnosed with gastrointestinal stromal tumors.

    PubMed

    Smith, Myles J; Smith, Henry G; Mahar, Alyson L; Law, Calvin; Ko, Yoo-Joung

    2016-10-15

    A higher incidence of additional malignancies has been described in patients diagnosed with gastrointestinal stromal tumors (GIST). This study aimed to identify risk factors for developing additional malignancies in patients diagnosed with GIST and evaluate the impact on survival. Individuals diagnosed with GIST from 2001 to2009 were identified from the SEER database. Logistic regression was used to identify predictors of additional malignancies and Cox-proportional hazards regression used to identify predictors of survival. In the study period, 1705 cases of GIST were identified, with 181 (10.6%) patients developing additional malignancies. Colorectal cancer was the most common cancer developing within 6 months of GIST diagnosis (30%). The median time to diagnosis of a malignancy after 6 months of GIST diagnosis was 21.9 months. Older age (p < 0.0001) and extraoesophagogastric GIST (p = 0.0027) were significant prognostic factors associated with additional malignancies. The overall 5-year survival was 65%, with the presence of additional malignancies within 6 months of GIST diagnosis associated with poor overall survival (54%, HR 1.55 1.05-2.3 95% CI, p = 0.04). Predictive factors of additional malignancies in patients diagnosed with GIST are increasing age and the primary disease site. Developing additional malignancies within 6 months of GIST diagnosis is associated with poorer overall survival. Targeted surveillance may be warranted in patients diagnosed with GIST that are at high risk of developing additional malignancies. PMID:27299364

  3. Effects of Roundup formulations, nutrient addition, and Western mosquitofish (Gambusia affinis) on aquatic communities.

    PubMed

    Geyer, Rebecca L; Smith, Geoffrey R; Rettig, Jessica E

    2016-06-01

    Aquatic communities can be affected by herbicides, nutrient addition, and non-native fish species. We conducted a mesocosm experiment to examine the direct and interactive effects of three stressors: (1) Roundup formulations (Roundup Weed and Grass Killer(®) and Roundup Poison Ivy and Tough Brush Killer Plus(®)), (2) nutrient addition, and (3) the presence of the non-native Western mosquitofish (Gambusia affinis), on experimental pond communities. Roundup formulations had the most widespread effects on the zooplankton community, but effects varied between formulations and among taxa. The only significant effect of nutrient addition was a lowering of Daphnia abundance in the nutrient addition treatments. The abundances of Daphnia, mid-sized cladocerans, and total zooplankton were lowered by mosquitofish, but no other taxa showed significant mosquitofish effects. We found several two-way and three-way interactions among the stressors, but these varied among zooplankton taxa. Chlorophyll a levels were higher with nutrient addition but were not significantly affected by Roundup formulation or mosquitofish. Our results suggest toxicity of Roundup formulations varies among taxa, and Roundup formulations differ in their toxicity to zooplankton, but with no cascading effects on primary producers. In addition, interactions among stressors affected the zooplankton community.

  4. Effects of Roundup formulations, nutrient addition, and Western mosquitofish (Gambusia affinis) on aquatic communities.

    PubMed

    Geyer, Rebecca L; Smith, Geoffrey R; Rettig, Jessica E

    2016-06-01

    Aquatic communities can be affected by herbicides, nutrient addition, and non-native fish species. We conducted a mesocosm experiment to examine the direct and interactive effects of three stressors: (1) Roundup formulations (Roundup Weed and Grass Killer(®) and Roundup Poison Ivy and Tough Brush Killer Plus(®)), (2) nutrient addition, and (3) the presence of the non-native Western mosquitofish (Gambusia affinis), on experimental pond communities. Roundup formulations had the most widespread effects on the zooplankton community, but effects varied between formulations and among taxa. The only significant effect of nutrient addition was a lowering of Daphnia abundance in the nutrient addition treatments. The abundances of Daphnia, mid-sized cladocerans, and total zooplankton were lowered by mosquitofish, but no other taxa showed significant mosquitofish effects. We found several two-way and three-way interactions among the stressors, but these varied among zooplankton taxa. Chlorophyll a levels were higher with nutrient addition but were not significantly affected by Roundup formulation or mosquitofish. Our results suggest toxicity of Roundup formulations varies among taxa, and Roundup formulations differ in their toxicity to zooplankton, but with no cascading effects on primary producers. In addition, interactions among stressors affected the zooplankton community. PMID:26944427

  5. Significance of postshunt ventricular asymmetries.

    PubMed

    Linder, M; Diehl, J T; Sklar, F H

    1981-08-01

    Ventricular asymmetries after shunt surgery were studied. Right and left ventricular areas from pre-and postoperative computerized tomography scans were measured with a computer digitizing technique, and the respective areas were expressed as a ratio. Measurements were made from the scans of 15 hydrocephalic children selected at random. Ages at surgery ranged from 1 to 101 weeks. The results indicate a significantly greater decrease in ventricular size on the side of the ventricular shunt catheter. Multiple regression analysis showed no relationship between the magnitude of change in ventricular size and either the patients' age orn the time intervals between surgery and follow-up scans. Possible mechanisms for these postshunt ventricular asymmetries are discussed.

  6. Yawning and its physiological significance

    PubMed Central

    Gupta, Sharat; Mittal, Shallu

    2013-01-01

    Although yawning is a commonly witnessed human behavior, yet it has not been taught in much detail in medical schools because, until the date, no particular physiological significance has been associated with it. It is characterized by opening up of mouth which is accompanied by a long inspiration, with a brief interruption of ventilation and followed by a short expiration. Since time immemorial, yawning has been associated with drowsiness and boredom. However, this age old belief is all set to change as the results of some newer studies have pointed out that yawning might be a way by which our body is trying to accomplish some more meaningful goals. In this review, we have tried to put together some of the important functions that have been proposed by a few authors, with the hope that this article will stimulate the interest of newer researchers in this hitherto unexplored field. PMID:23776833

  7. Decontamination formulation with sorbent additive

    DOEpatents

    Tucker; Mark D. , Comstock; Robert H.

    2007-10-16

    A decontamination formulation and method of making that neutralizes the adverse health effects of both chemical and biological compounds, especially chemical warfare (CW) and biological warfare (BW) agents, and toxic industrial chemicals. The formulation provides solubilizing compounds that serve to effectively render the chemical and biological compounds, particularly CW and BW compounds, susceptible to attack, and at least one reactive compound that serves to attack (and detoxify or kill) the compound. The formulation includes at least one solubilizing agent, a reactive compound, a bleaching activator, a sorbent additive, and water. The highly adsorbent, water-soluble sorbent additive (e.g., sorbitol or mannitol) is used to "dry out" one or more liquid ingredients, such as the liquid bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate) and convert the activator into a dry, free-flowing powder that has an extended shelf life, and is more convenient to handle and mix in the field.

  8. Additive concentrates for distillate fuels

    SciTech Connect

    Rossi, A.; Lewtas, K.

    1985-08-27

    An additive concentrate for incorporation into wax containing petroleum fuel oil compositions to improve low temperature flow properties comprising an oil solution containing: 3% to 90 wt. % of a C30-C300 oil-soluble nitrogen compound wax crystal growth inhibitor having at least one straight C8-C40 alkyl chain and partial esters, and at least one mole per mole of an organic acid capable of hydrogen bonding to improve the solubility in the oil.

  9. Additive manufacturing of hybrid circuits

    DOE PAGES

    Bell, Nelson S.; Sarobol, Pylin; Cook, Adam; Clem, Paul G.; Keicher, David M.; Hirschfeld, Deidre; Hall, Aaron Christopher

    2016-03-26

    There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects.more » Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. As a result, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.« less

  10. Theoretical and experimental investigation of additive drag

    NASA Technical Reports Server (NTRS)

    Sibulkin, Merwin

    1954-01-01

    The significance of additive drag is discussed and equations for determining its approximate value are derived for annular and open-nose inlets. Charts are presented giving values of additive drag coefficient over a range of free-stream Mach numbers for open and for annular-nose inlets with conical flow at the inlet. The effects on additive drag of variable inlet-total-pressure recovery and static pressures on the centerbody are investigated and an analytical method of predicting the variation of pressure on the centerbody with mass-flow ratio is given. Experimental additive-drag values are presented for a series of 20 degree and 25 degree cone half-angle inlets and one open-nose inlet operating at free-stream Mach numbers of 1.8 and 1.6. A comparison with the theoretical values of additive drag shows excellent agreement for the open-nose inlet and moderately good agreement for the annular inlets. (author)

  11. Fuel and Additive Characterization for HCCI Combustion

    SciTech Connect

    Aceves, S M; Flowers, D; Martinez-Frias, J; Espinosa-Loza, F; Pitz, W J; Dibble, R

    2003-02-12

    This paper shows a numerical evaluation of fuels and additives for HCCl combustion. First, a long list of candidate HCCl fuels is selected. For all the fuels in the list, operating conditions (compression ratio, equivalence ratio and intake temperature) are determined that result in optimum performance under typical operation for a heavy-duty engine. Fuels are also characterized by presenting Log(p)-Log(T) maps for multiple fuels under HCCl conditions. Log(p)-Log(T) maps illustrate important processes during HCCl engine operation, including compression, low temperature heat release and ignition. Log(p)-Log(T) diagrams can be used for visualizing these processes and can be used as a tool for detailed analysis of HCCl combustion. The paper also includes a ranking of many potential additives. Experiments and analyses have indicated that small amounts (a few parts per million) of secondary fuels (additives) may considerably affect HCCl combustion and may play a significant role in controlling HCCl combustion. Additives are ranked according to their capability to advance HCCl ignition. The best additives are listed and an explanation of their effect on HCCl combustion is included.

  12. Alabama Commission on Higher Education. Occasional Papers on Higher Education.

    ERIC Educational Resources Information Center

    Alabama State Commission on Higher Education, Montgomery.

    Two papers on the funding formula of the Alabama Commission for Higher Education are presented. The first paper, by John F. Porter, Jr., "The Origins and Evolutions of the Funding Formula Model Utilized by the Alabama Commission on Higher Education, 1973-82," presents the historical antecedents for the existing formula elements and notes…

  13. On higher holonomy invariants in higher gauge theory I

    NASA Astrophysics Data System (ADS)

    Zucchini, Roberto

    2016-05-01

    This is the first of a series of two technical papers devoted to the analysis of holonomy invariants in strict higher gauge theory with end applications in higher Chern-Simons theory. For a flat 2-connection, we define the 2-holonomy of surface knots of arbitrary genus and determine its covariance properties under 1-gauge transformation and change of base data.

  14. Internationalization and Culture in Higher Education

    ERIC Educational Resources Information Center

    Lumby, Jacky; Foskett, Nick

    2016-01-01

    Internationalization has attained great significance in Higher Education, driven by both educational philosophy and commercial imperatives. Cultural change is implied as both a related process and as a goal. The article considers the multifaceted ways in which culture might be conceived and linked to different orientations to internationalization.…

  15. Financing Higher Education: Lessons from China

    ERIC Educational Resources Information Center

    Fengliang, Li

    2012-01-01

    In China, debates about higher education finance led to the introduction of a cost-sharing model, whereby students were required to pay tuition fees, over a decade ago. However, there is still significant resistance towards such a system within the broader society. In order to share insights into the development of the cost-sharing policy in China…

  16. Regional Plan for Texas Higher Education.

    ERIC Educational Resources Information Center

    Texas Higher Education Coordinating Board, 2004

    2004-01-01

    This report was developed in response to Texas Education Code 61.051(i), requiring the Coordinating Board to develop a long-range plan for higher education, by region. A wide variety of factors, including educational attainment of the current population, existing degree programs, programs where significant unmet need may exist, programs provided…

  17. Evolving Computer Networks in American Higher Education.

    ERIC Educational Resources Information Center

    McCredie, John W.; Timlake, William P.

    1983-01-01

    Traditions and pressures in the academic environment accounting for early and continuing involvement of higher education with computer networking are described. Several established networks illustrating the wide range of academic applications currently available as well as policy issues of particular significance in academic networks are…

  18. Mark Edwards: Mission Impossible in Higher Education?

    ERIC Educational Resources Information Center

    Santora, Joseph C.; Sarros, James C.

    2008-01-01

    This case chronicles some of the problems a corporate executive encountered on his transition from the private sector to the deanship of the College of Business in a university of higher education. His deanship, which resulted from the recent reorganization at State University, gave him significant responsibility for undergraduate and graduate…

  19. Higher Education for Sustainable Development in China

    ERIC Educational Resources Information Center

    Niu, Dongjie; Jiang, Dahe; Li, Fengting

    2010-01-01

    Purpose: The purpose of this paper is to analyse the significance of developments across Chinese higher education in the field of education and learning for sustainable development (SD) and to assess the relative impact of these initiatives. Design/methodology/approach: This is a review of policy and practice to examine developments, challenges,…

  20. Personal Broadcasting: Applications in Higher Education

    ERIC Educational Resources Information Center

    Wolf, Patricia D.

    2007-01-01

    Personal Broadcasting, which includes podcasting, vodcasting, phonecasting, Webcasting, blogging, and wikis, is one of the emerging technologies that will have a significant effect on education within the next five years. This article describes the techniques used in personal broadcasting, describes how they are being used in higher education,…

  1. Outsourcing in Higher Education: An Empirical Examination

    ERIC Educational Resources Information Center

    Gupta, Atul; Herath, S. Kanthi; Mikouiza, Nathalie C.

    2005-01-01

    Purpose: To measure the degree of implementation and satisfaction level with the outsourcing initiatives from higher education institutions. Design/methodology/approach: Uses a survey questionnaire to measure the levels of satisfaction with the institutions' services and the questionnaire was based on six factors that are deemed significant in…

  2. Higher Education and the Corporate Sector.

    ERIC Educational Resources Information Center

    Stetar, Joseph M.

    Most of the people who are involved in higher education recognize that corporate interest in developing significant, job-related educational opportunities is growing. The motivation to provide corporate educational programs ranges from the need to improve skills to an interest in responding to legal and social responsibilities by expanding…

  3. Peer Effects in Higher Education. Discussion Paper.

    ERIC Educational Resources Information Center

    Winston, Gordon C.; Zimmerman, David J.

    This paper, prepared as a chapter for a forthcoming book, describes the potential significance of student peer effects for the economic structure and behavior of higher education. The existence of student peer effects would motivate much of the restricted supply, student queuing, and selectivity, and institutional competition via merit and honors…

  4. Retrofitting the 5045 Klystron for Higher Efficiency

    SciTech Connect

    Jensen, Aaron; Fazio, Michael; Haase, Andy; Jongewaard, Erik; Kemp, Mark; Neilson, Jeff

    2015-04-15

    The 5045 klystron has been in production and accelerating particles at SLAC National Accelerator Laboratory for over 25 years. Although the design has undergone some changes there are still significant opportunities for improvement in performance. Retrofitting the 5045 for higher efficiencies and a more mono-energetic spent beam profile is presented.

  5. Improving Measurement of Productivity in Higher Education

    ERIC Educational Resources Information Center

    Sullivan, Teresa A., Ed.; Mackie, Christopher, Ed.; Massy, William F., Ed.; Sinha, Esha, Ed.

    2012-01-01

    Higher education is a linchpin of the American economy and society: Teaching and research at colleges and universities contribute significantly to the nation's economic activity, both directly and through their impact on future growth; federal and state governments support teaching and research with billions of taxpayers' dollars; and individuals,…

  6. Fortification of yogurts with different antioxidant preservatives: A comparative study between natural and synthetic additives.

    PubMed

    Caleja, Cristina; Barros, Lillian; Antonio, Amilcar L; Carocho, Márcio; Oliveira, M Beatriz P P; Ferreira, Isabel C F R

    2016-11-01

    Consumers demand more and more so-called "natural" products and, therefore, the aim of this work was to compare the effects of natural versus synthetic antioxidant preservatives in yogurts. Matricaria recutita L. (chamomile) and Foeniculum vulgare Mill. (fennel) decoctions were tested as natural additives, while potassium sorbate (E202) was used as a synthetic additive. The fortification of yogurts with natural and synthetic antioxidants did not cause significant changes in the yoghurt pH and nutritional value, in comparison with control samples (yogurt without any additive). However, the fortified yogurts showed higher antioxidant activity, mainly the yogurts with natural additives (and among these, the ones with chamomile decoction). Overall, it can be concluded that plant decoctions can be used to develop novel yogurts, by replacing synthetic preservatives and improving the antioxidant properties of the final product, without changing the nutritional profile. PMID:27211646

  7. Alkoxyboration: Ring-Closing Addition of B–O σ Bonds across Alkynes

    PubMed Central

    2015-01-01

    For nearly 70 years, the addition of boron–X σ bonds to carbon–carbon multiple bonds has been employed in the preparation of organoboron reagents. However, the significantly higher strength of boron–oxygen bonds has thus far precluded their activation for addition, preventing a direct route to access a potentially valuable class of oxygen-containing organoboron reagents for divergent synthesis. We herein report the realization of an alkoxyboration reaction, the addition of boron–oxygen σ bonds to alkynes. Functionalized O-heterocyclic boronic acid derivatives are produced using this transformation, which is mild and exhibits broad functional group compatibility. Our results demonstrate activation of this boron–O σ bond using a gold catalysis strategy that is fundamentally different from that used previously for other boron addition reactions. PMID:24588331

  8. Fortification of yogurts with different antioxidant preservatives: A comparative study between natural and synthetic additives.

    PubMed

    Caleja, Cristina; Barros, Lillian; Antonio, Amilcar L; Carocho, Márcio; Oliveira, M Beatriz P P; Ferreira, Isabel C F R

    2016-11-01

    Consumers demand more and more so-called "natural" products and, therefore, the aim of this work was to compare the effects of natural versus synthetic antioxidant preservatives in yogurts. Matricaria recutita L. (chamomile) and Foeniculum vulgare Mill. (fennel) decoctions were tested as natural additives, while potassium sorbate (E202) was used as a synthetic additive. The fortification of yogurts with natural and synthetic antioxidants did not cause significant changes in the yoghurt pH and nutritional value, in comparison with control samples (yogurt without any additive). However, the fortified yogurts showed higher antioxidant activity, mainly the yogurts with natural additives (and among these, the ones with chamomile decoction). Overall, it can be concluded that plant decoctions can be used to develop novel yogurts, by replacing synthetic preservatives and improving the antioxidant properties of the final product, without changing the nutritional profile.

  9. [Epilepsy with higher brain dysfunction].

    PubMed

    Sugimoto, Azusa; Midorikawa, Akira; Koyama, Shinichi; Futamura, Akinori; Kuroda, Takeshi; Fujita, Kazuhisa; Itaya, Kazuhiro; Ishigaki, Seiichiro; Kawamura, Mitsuru

    2013-02-01

    Acquired higher brain dysfunction is for the most part due to cerebral vascular disease, but epilepsy may also be a cause. In this study with five patients, we discuss the advantages of anti-epileptic drugs (AEDs) for persistent higher brain dysfunction. The patients showed chronic amnesia or acute aphasia, with associated symptoms like personality change. All five cases affected automatism or convulsive attack, though only after the emergence of higher brain dysfunction and administration of AEDs. There were underlying diseases like cerebral arteriovenous malformation in four cases, but the other patient had none. Electroencephalogram and single photon emission computed tomography revealed one case of aphasia epilepsy with higher brain dysfunction. These results suggest the potential therapeutic efficacy of AEDs for persistent higher brain dysfunction, and we must differentiate epilepsy with higher brain dysfunction from dementia or cerebral vascular disease. PMID:23399676

  10. Evaluation of certain food additives.

    PubMed

    2009-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to recommending acceptable daily intakes (ADIs) and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation and assessment of intake of food additives (in particular, flavouring agents). A summary follows of the Committee's evaluations of technical, toxicological and intake data for certain food additives (asparaginase from Aspergillus niger expressed in A. niger, calcium lignosulfonate (40-65), ethyl lauroyl arginate, paprika extract, phospholipase C expressed in Pichia pastoris, phytosterols, phytostanols and their esters, polydimethylsiloxane, steviol glycosides and sulfites [assessment of dietary exposure]) and 10 groups of related flavouring agents (aliphatic branched-chain saturated and unsaturated alcohols, aldehydes, acids and related esters; aliphatic linear alpha,beta-unsaturated aldehydes, acids and related alcohols, acetals and esters; aliphatic secondary alcohols, ketones and related esters; alkoxy-substituted allylbenzenes present in foods and essential oils and used as flavouring agents; esters of aliphatic acyclic primary alcohols with aliphatic linear saturated carboxylic acids; furan-substituted aliphatic hydrocarbons, alcohols, aldehydes, ketones, carboxylic acids and related esters, sulfides, disulfides and ethers; miscellaneous nitrogen-containing substances; monocyclic and bicyclic secondary alcohols, ketones and related esters; hydroxy- and alkoxy-substituted benzyl derivatives; and substances structurally related to menthol). Specifications for the following food additives were revised: canthaxanthin; carob bean gum and carob bean gum (clarified); chlorophyllin copper complexes, sodium and potassium salts; Fast Green FCF; guar gum and guar gum (clarified

  11. Fire-Retardant Polymeric Additives

    NASA Technical Reports Server (NTRS)

    Williams, Martha K.; Smith, Trent M.

    2011-01-01

    Polyhydroxyamide (PHA) and polymethoxyamide (PMeOA) are fire-retardant (FR) thermoplastic polymers and have been found to be useful as an additive for imparting fire retardant properties to other compatible, thermoplastic polymers (including some elastomers). Examples of compatible flammable polymers include nylons, polyesters, and acrylics. Unlike most prior additives, PHA and PMeOA do not appreciably degrade the mechanical properties of the matrix polymer; indeed, in some cases, mechanical properties are enhanced. Also, unlike some prior additives, PHA and PMeOA do not decompose into large amounts of corrosive or toxic compounds during combustion and can be processed at elevated temperatures. PMeOA derivative formulations were synthesized and used as an FR additive in the fabrication of polyamide (PA) and polystyrene (PS) composites with notable reduction (>30 percent for PS) in peak heat release rates compared to the neat polymer as measured by a Cone Calorimeter (ASTM E1354). Synergistic effects were noted with nanosilica composites. These nanosilica composites had more than 50-percent reduction in peak heat release rates. In a typical application, a flammable thermoplastic, thermoplastic blend, or elastomer that one seeks to render flame-retardant is first dry-mixed with PHA or PMeOA or derivative thereof. The proportion of PHA or PMeOA or derivative in the mixture is typically chosen to lie between 1 and 20 weight percent. The dry blend can then be melt-extruded. The extruded polymer blend can further be extruded and/or molded into fibers, pipes, or any other of a variety of objects that may be required to be fire-retardant. The physical and chemical mechanisms which impart flame retardancy of the additive include inhibiting free-radical oxidation in the vapor phase, preventing vaporization of fuel (the polymer), and cooling through the formation of chemical bonds in either the vapor or the condensed phase. Under thermal stress, the cyclic hydroxyl/ methoxy

  12. On higher dimensional exact Courant algebroids

    NASA Astrophysics Data System (ADS)

    Rengifo, Camilo

    2016-09-01

    For a smooth manifold X we show an equivalence of categories between the category of OX♯ [ n ] -extensions of TX♯ and the category of higher-dimensional exact Courant algebroids on X. In addition, for any object in the category of R [ n ] dg-principal bundles over X♯ we construct its Atiyah algebroid which gives rise to an example of OX♯ [ n ] -extensions of TX♯.

  13. A 110-year perspective of significant tornadoes

    NASA Astrophysics Data System (ADS)

    Grazulis, Thomas P.

    A tornado documentation project began in 1980 as an effort to resolve differences between the two independently designed tornado data bases used by the Nuclear Regulatory Commission (NRC). One was established for the NRC at the University of Chicago (UC) by T. T. Fujita for the years 1916-1985. In addition, the NRC assisted the National Severe Storms Forecast Center (NSSFC) in adding F scale ratings to the existing NSSFC data base in Kansas City, from 1950 to the present. The final task of this effort (hereinafter called the project) was to locate and list all significant tornadoes from 1880 through 1989. Significant is defined here as all tornadoes doing confirmable F-2 or greater damage or causing a death.

  14. Astrobiological Significance of Chemolithoautotrophic Acidophiles

    NASA Technical Reports Server (NTRS)

    Pikuta, Elena V.; Hoover, Richard B.

    2003-01-01

    For more than a century (since Winogradsky discovered lithoautotrophic bacteria) a dilemma in microbiology has concerned life that first inhabited the Earth. Which types of life forms first appeared in the primordial oceans during the earliest geological period on Earth as the primary ancestors of modem biological diversity? How did a metabolism of ancestors evolve: from lithoautotrophic to lithohetherotrophic and organoheterotrophic or from organoheterotrophic to organoautotrophic and lithomixotrophic types? At the present time, it is known that chemolithoheterotrophic and chemolithoautotrophic metabolizing bacteria are wide spread in different ecosystems. On Earth the acidic ecosystems are associated with geysers, volcanic fumaroles, hot springs, deep sea hydrothermal vents, caves, acid mine drainage and other technogenic ecosystems. Bioleaching played a significant role on a global geological scale during the Earth's formation. This important feature of bacteria has been successfully applied in industry. The lithoautotrophs include Bacteria and Archaea belonging to diverse genera containing thermophilic and mesophilic species. In this paper we discuss the lithotrophic microbial acidophiles and present some data with a description of new acidophilic iron- and sulfur- oxidizing bacterium isolated from the Chena Hot Springs in Alaska. We also consider the possible relevance of microbial acidophiles to Venus, Io, and acidic inclusions in glaciers and icy moons.

  15. Polysaccharides: Occurrence, Significance, and Properties

    NASA Astrophysics Data System (ADS)

    Bemiller, James N.

    Polysaccharides are properties present significance in all living organisms where they carry out one or more of their diverse functions. While there is no specific category or definition of a complex polysaccharide, most are structurally complex. Polysaccharides contain 1-5 different monosaccharide (sugar) units. The different sugar units may have different anomeric configurations and/or be joined by different glycosidic linkages. Polysaccharides may be linear or branched. Branches may be short saccharide units on a linear backbone or the molecule may have a branch-on-branch structure; in either case, the branches may be isolated or clustered. Polysaccharides may contain non-carbohydrate groups. Esters or cyclic acetal groups, when present, can be removed by appropriate treatments. All polysaccharides are polydisperse, i. e., are present in a range of molecular weights rather than having a single molecular weight. Most are polymolecular, i. e., differ in fine structure from molecule to molecule. So most polysaccharides can be said to be structurally complex. They may be attached to protein molecules or to other polysaccharide molecules. They are solvated by water. Most dissolve in aqueous systems, especially if they are alkaline. Polysaccharides can be depolymerized by acids and heat, specific enzymes, and high pH systems following oxidation. Their hydroxyl groups can be esterified (acylated), etherified (alkylated), and oxidized. Amino groups can be acylated (and deacylated). Carboxyl groups can be converted into esters, amides, and amines. Structural modification makes the molecules even more complex and polymolecular and, perhaps, polydisperse.

  16. Statistically significant relational data mining :

    SciTech Connect

    Berry, Jonathan W.; Leung, Vitus Joseph; Phillips, Cynthia Ann; Pinar, Ali; Robinson, David Gerald; Berger-Wolf, Tanya; Bhowmick, Sanjukta; Casleton, Emily; Kaiser, Mark; Nordman, Daniel J.; Wilson, Alyson G.

    2014-02-01

    This report summarizes the work performed under the project (3z(BStatitically significant relational data mining.(3y (BThe goal of the project was to add more statistical rigor to the fairly ad hoc area of data mining on graphs. Our goal was to develop better algorithms and better ways to evaluate algorithm quality. We concetrated on algorithms for community detection, approximate pattern matching, and graph similarity measures. Approximate pattern matching involves finding an instance of a relatively small pattern, expressed with tolerance, in a large graph of data observed with uncertainty. This report gathers the abstracts and references for the eight refereed publications that have appeared as part of this work. We then archive three pieces of research that have not yet been published. The first is theoretical and experimental evidence that a popular statistical measure for comparison of community assignments favors over-resolved communities over approximations to a ground truth. The second are statistically motivated methods for measuring the quality of an approximate match of a small pattern in a large graph. The third is a new probabilistic random graph model. Statisticians favor these models for graph analysis. The new local structure graph model overcomes some of the issues with popular models such as exponential random graph models and latent variable models.

  17. Determining Semantically Related Significant Genes.

    PubMed

    Taha, Kamal

    2014-01-01

    GO relation embodies some aspects of existence dependency. If GO term xis existence-dependent on GO term y, the presence of y implies the presence of x. Therefore, the genes annotated with the function of the GO term y are usually functionally and semantically related to the genes annotated with the function of the GO term x. A large number of gene set enrichment analysis methods have been developed in recent years for analyzing gene sets enrichment. However, most of these methods overlook the structural dependencies between GO terms in GO graph by not considering the concept of existence dependency. We propose in this paper a biological search engine called RSGSearch that identifies enriched sets of genes annotated with different functions using the concept of existence dependency. We observe that GO term xcannot be existence-dependent on GO term y, if x- and y- have the same specificity (biological characteristics). After encoding into a numeric format the contributions of GO terms annotating target genes to the semantics of their lowest common ancestors (LCAs), RSGSearch uses microarray experiment to identify the most significant LCA that annotates the result genes. We evaluated RSGSearch experimentally and compared it with five gene set enrichment systems. Results showed marked improvement.

  18. Astrobiological significance of chemolithoautotrophic acidophiles

    NASA Astrophysics Data System (ADS)

    Pikuta, Elena V.; Hoover, Richard B.

    2004-02-01

    For more than a century (since Winogradsky discovered lithautotrophic bacteria) there has been a dilemma in microbiology about life that first inhabited the Earth. Which types of life forms first appeared in the primordial oceans during the earliest geological period on Earth as the primary ancestors of modern biological diversity? How did a metabolism of ancestors evolve: from lithoautotrophic to lithoheterotrophic and organoheterotrophic or from organoheterotrophic to organautotrophic and lithomixotrophic types? At the present time, it is known that chemolithoheterotrophic and chemolithoautotrophic metabolizing bacteria are wide spread in different ecosystems. On Earth the acidic ecosystems are associated with geysers, volcanic fumaroles, hot springs, deep sea hydrothermal vents, caves, acid mine drainage and other technogenic ecosystems. Bioleaching played a significant roel on a global geological scale during the Earth's formation. This important feature of bacteria has been successfully applied in industry. The lithoautotrophs include Bacteria and Archaea belonging to diverse genera containing thermophilic and mesophilic species. In this paper we discuss the lithotrophic microbial acidophiles and present some data with a description of new acidophilic iron- and sulfur-oxidizing bacterium isolated from the Chena Hot Springs in Alaska. We also consider the possible relevance of microbial acidophiles to Venus, Io, and acidic inclusions in glaciers and icy moons.

  19. Clinical significance of lymphadenectomy in patients with gastric cancer.

    PubMed

    Tóth, Dezső; Plósz, János; Török, Miklós

    2016-02-15

    Approximately thirty percent of patients with gastric cancer undergo an avoidable lymph node dissection with a higher rate of postoperative complication. Comparing the D1 and D2 dissections, it was found that there is a significant difference in morbidity, favoured D1 dissection without any difference in overall survival. Subgroup analysis of patients with T3 tumor shows a survival difference favoring D2 lymphadenectomy, and there is a better gastric cancer-related death and non-statistically significant improvement of survival for node-positive disease in patients with D2 dissection. However, the extended lymphadenectomy could improve stage-specific survival owing to the stage migration phenomenon. The deployment of centralization and application of national guidelines could improve the surgical outcomes. The Japanese and European guidelines enclose the D2 lymphadenectomy as the gold standard in R0 resection. In the individualized, stage-adapted gastric cancer surgery the Maruyama computer program (MCP) can estimate lymph node involvement preoperatively with high accuracy and in addition the Maruyama Index less than 5 has a better impact on survival, than D-level guided surgery. For these reasons, the preoperative application of MCP is recommended routinely, with an aim to perform "low Maruyama Index surgery". The sentinel lymph node biopsy (SNB) may decrease the number of redundant lymphadenectomy intraoperatively with a high detection rate (93.7%) and an accuracy of 92%. More accurate stage-adapted surgery could be performed using the MCP and SNB in parallel fashion in gastric cancer.

  20. Metal Additive Manufacturing: A Review

    NASA Astrophysics Data System (ADS)

    Frazier, William E.

    2014-06-01

    This paper reviews the state-of-the-art of an important, rapidly emerging, manufacturing technology that is alternatively called additive manufacturing (AM), direct digital manufacturing, free form fabrication, or 3D printing, etc. A broad contextual overview of metallic AM is provided. AM has the potential to revolutionize the global parts manufacturing and logistics landscape. It enables distributed manufacturing and the productions of parts-on-demand while offering the potential to reduce cost, energy consumption, and carbon footprint. This paper explores the material science, processes, and business consideration associated with achieving these performance gains. It is concluded that a paradigm shift is required in order to fully exploit AM potential.

  1. Cast Stone Formulation At Higher Sodium Concentrations

    SciTech Connect

    Fox, K. M.; Edwards, T. A.; Roberts, K. B.

    2013-10-02

    concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The

  2. Cast Stone Formulation At Higher Sodium Concentrations

    SciTech Connect

    Fox, K. M.; Roberts, K. A.; Edwards, T. B.

    2014-02-28

    concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leachability indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste

  3. Cast Stone Formulation At Higher Sodium Concentrations

    SciTech Connect

    Fox, K. M.; Roberts, K. A.; Edwards, T. B.

    2013-09-17

    concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The

  4. New Labour and Higher Education

    ERIC Educational Resources Information Center

    Watson, David

    2006-01-01

    This paper, the first part of an edited version of a Keynote Presentation delivered at the AUA Annual Conference, Queen's University Belfast, on April 11, 2006, describes the fate of UK higher education during the course of the last parliament and identifies New Labour's two successive and contradictory higher education policies. The author…

  5. The Higher Education Research Archipelago

    ERIC Educational Resources Information Center

    Macfarlane, Bruce

    2012-01-01

    Ever since he stumbled into doing higher education research as a young academic in the 1980s, the author has been trying to understand it as a "field" of study. His career, as a former business lecturer, then an academic developer and now an associate professor for higher education working in an Education Faculty has given him opportunities to see…

  6. The Economy and Higher Education.

    ERIC Educational Resources Information Center

    Anderson, Richard E.

    1988-01-01

    The macroeconomic trends shaping the United States economy and the effects of those trends on higher education are considered. Warning institutions of higher education about possible problems in the economy will place them in a better position to react if necessary. The economic environment is discussed in terms of productivity (goods and services…

  7. "Accessions": Researching, Designing Higher Education

    ERIC Educational Resources Information Center

    Taylor, Yvette

    2011-01-01

    This brief viewpoint piece depicts educational (dis)engagements apparent in researching and (re)designing higher education in and through "Accessions". "Accessions", a collaborative research-design project, probed at how cultures, climates and conditions of higher education may be reproducing or reshaping social inequalities and divisions. Here,…

  8. Theorising Quality in Higher Education

    ERIC Educational Resources Information Center

    Morley, Louise

    2004-01-01

    Britain now has the most heavily regulated higher education system in the world and institutions must deliver best educational value. This book explores the political and psychic economy of quality assurance in higher education and interrogates the discourse and practices associated with the audit culture in Britain. Following Acknowledgements and…

  9. Disability Discrimination in Higher Education.

    ERIC Educational Resources Information Center

    Weber, Mark C.

    1999-01-01

    Reviewed 1998 and early 1999 court decisions related to disability discrimination in higher education. This period witnessed major developments in the law of disability discrimination as it relates to higher education. A major focus was on whether persons whose impairments are ameliorated by treatment are individuals with disabilities covered by…

  10. Funding Higher Education: Student Perspectives.

    ERIC Educational Resources Information Center

    Mason, Selena; Harvey, Lee

    This report documents the results of a survey of 1,139 students at the University of Central England (UCE) in Birmingham in regard to their financial circumstances and their views on the funding of higher education. The report also examines the advantages and disadvantages of six specific higher education funding proposals put forth in recent…

  11. Higher Education, Poverty and Development

    ERIC Educational Resources Information Center

    Tilak, Jandhyala B. G.

    2010-01-01

    There is a presumption among many policy makers that higher education is not necessary for economic growth and development; it is literacy and basic education and at best secondary education that are argued to be important. Estimates of internal rate of return contributed to strengthening of such a presumption. Accordingly, higher education has…

  12. History of American Higher Education

    ERIC Educational Resources Information Center

    McCarthy, Margaret Cain

    2011-01-01

    "History of American Higher Education" documents the fascinating evolution of American colleges and universities, touching on the historical events that shaped them, from the colonial era through the early twenty-first century. Throughout history, higher education has played an important role in the transmission of cultural identity from one…

  13. Personnel Management in Higher Education.

    ERIC Educational Resources Information Center

    Millett, John D.; And Others

    This document on personnel management in higher education contains three papers that are designed to be used as guidelines for educational administrators. The first two papers, by John D. Millett, discuss the scope and problems of higher education administration and the problems associated with collective bargaining and tenure on college campuses.…

  14. Fact Book on Higher Education

    ERIC Educational Resources Information Center

    Marks, Joseph L.; Diaz, Alicia A.

    2009-01-01

    The "Southern Regional Education Board (SREB) Fact Book on Higher Education" is one of the nation's most comprehensive collections of comparative data on higher education. For decades, state leaders, policy-makers, researchers and journalists have used the "Fact Book" to find useful data quickly--and to learn more about long-term trends and…

  15. Alternative Models for Higher Education.

    ERIC Educational Resources Information Center

    Caffrey, John G.

    Higher education is beset from all sides by criticism, fear, doubt, uncertainty, and prophecies of doom. While the young call for change, the faculty often resist anything that might reduce their privileges and prerogatives. Before alternative models to the present system of higher education can be considered, it is useful to question present…

  16. Exploring Higher Education Financing Options

    ERIC Educational Resources Information Center

    Nkrumah-Young, Kofi K.; Powell, Philip

    2011-01-01

    Higher education can be financed privately, financed by governments, or shared. Given that the benefits of education accrue to the individual and the state, many governments opt for shared financing. This article examines the underpinnings of different options for financing higher education and develops a model to compare conditions to choices and…

  17. Sexual Harassment in Higher Education.

    ERIC Educational Resources Information Center

    Truax, Anne; And Others

    1989-01-01

    An article and three responses on sexual harassment in higher education are presented: "Sexual Harassment in Higher Education: What We've Learned" (Anne Truax); "Who Is Responsible for Sexual Harassment?" (Barbara G. Taylor); "The Feminist-Unionist Dilemma" (Sherna Berger Gluck); and "Sexual Harassment and Academic Power" (Loralee MacPike). (MLW)

  18. Postmodernism in Higher Educational Administration

    ERIC Educational Resources Information Center

    Demaris, Michalyn C.; Kritsonis, William Allan

    2007-01-01

    Postmodernism has many inferences that can be applied to the theory and practice of higher educational administration. Today, in higher education administrators are continuously focused on strategies that will ensure the future of minority educational institutions. As a result postmodernism is an important factor in the future of higher…

  19. Queering Transformation in Higher Education

    ERIC Educational Resources Information Center

    Msibi, Thabo

    2013-01-01

    Transformation in higher education has tended to focus on race and sex, at the expense of other forms of discrimination. This article addresses the silencing of "queer" issues in higher education. Using queer theory as a framework, and drawing on current literature, popular media reports, two personal critical incidents and a project…

  20. Effective Communication in Higher Education

    ERIC Educational Resources Information Center

    Howard, Melissa

    2014-01-01

    The intent for this paper is to show that communication within the higher education field is a current problem. By looking first at the different styles, forms, and audiences for communication, the reader will hopefully gain perspective as to why this is such a problem in higher education today. Since the Millennial generation is the newest set of…

  1. Higher Education, Employability and Competitiveness

    ERIC Educational Resources Information Center

    Pavlin, Samo; Svetlicic, Marjan

    2012-01-01

    This paper studies the relationship between competitiveness and higher education systems in Europe. It explores whether more competitive countries have developed more labour-market-oriented systems of higher education (HE) that thereby give their graduates greater short term employability potential. Based on and a large-scale survey among 45.000…

  2. Strategic Planning for Higher Education.

    ERIC Educational Resources Information Center

    Kotler, Philip; Murphy, Patrick E.

    1981-01-01

    The framework necessary for achieving a strategic planning posture in higher education is outlined. The most important benefit of strategic planning for higher education decision makers is that it forces them to undertake a more market-oriented and systematic approach to long- range planning. (Author/MLW)

  3. The Marketing of Higher Education.

    ERIC Educational Resources Information Center

    Brooker, George; Noble, Michael

    1985-01-01

    Formal college and university marketing programs are challenging to develop and implement because of the complexity of the marketing mix, the perceived inappropriateness of a traditional marketing officer, the number of diverse groups with input, the uniqueness of higher education institutions, and the difficulty in identifying higher education…

  4. Higher Education: Open for Business

    ERIC Educational Resources Information Center

    Gilde, Christian, Ed.

    2007-01-01

    This book addresses a problem in higher learning, which is newly recognized in the academic spotlight: the overcommercialization of higher education. The book asks that you, the reader, think about the following: Did you go to a Coke or Pepsi school? Do your children attend a Nike or Adidas school? Is the college in your town a Dell or Gateway…

  5. Empowering Women in Higher Education.

    ERIC Educational Resources Information Center

    Wisker, Gina

    This book focuses on enabling and empowering women in higher education, and it draws both on research and experience with women-centered teaching and learning practices and professional development and training of women staff. The first section of the book concentrates on women students in higher education. Chapters include: "Women Students and…

  6. THE ECONOMICS OF HIGHER EDUCATION.

    ERIC Educational Resources Information Center

    CARTTER, ALLAN M.; AND OTHERS

    THIS PUBLICATION CONTAINS PAPERS PRESENTED AT A COLLOQUIUM HELD BY THE COLLEGE SCHOLARSHIP SERVICE IN 1965. THE PAPERS DEAL BROADLY WITH THE QUESTION OF THE MOST EFFECTIVE METHODS OF FINANCING HIGHER EDUCATION, AND WITH THE ROLE AND PROBLEMS OF THE EDUCATIONAL CONSUMER. THE PAPERS DEAL WITH--(1) THE ECONOMICS OF HIGHER EDUCATION, (2) PRICING…

  7. Higher Education in New York.

    ERIC Educational Resources Information Center

    Lane, Frederick, Ed.

    1983-01-01

    New York State higher education policy and finance are discussed in four articles. In "Higher Education and Public Policy in New York," Frederick S. Lane considers the state's institutions, policymakers and politics, financing of colleges, enrollment patterns, links to economic development, and the changing educational environment. Paul T.…

  8. Higher Education and Social Commitment.

    ERIC Educational Resources Information Center

    Nasution, S.; Virasai, Banphot, Eds.

    The proceedings of the Regional Institute of Higher Education and Development's seminar and the meaning and implications of social commitment in higher education are reported. The welcoming address (S. Nasution) and the opening address (Y. B. Dato' Murad bin Mohd. Noor) welcome the participants and set the tone for the discussions to follow. The…

  9. Learning Entrepreneurship in Higher Education

    ERIC Educational Resources Information Center

    Taatila, Vesa P.

    2010-01-01

    Purpose: There is a constant need to produce more entrepreneurial graduates from higher education institutions. This paper aims to present and discuss several successful cases of entrepreneurial learning environments in order to suggest some important aspects that higher education institutions should consider. Design/methodology/approach: The…

  10. The Higher Learning in America.

    ERIC Educational Resources Information Center

    Hutchins, Robert M.

    1999-01-01

    Analysis of the state of public higher education in the United States focuses on government financing of higher education, the high costs of both government and good education, and student attitudes toward their education. A new general education curriculum design at the University of Chicago (Illinois), designed to alleviate some of these…

  11. Innovations in Higher Education? Hah!

    ERIC Educational Resources Information Center

    Kirschner, Ann

    2012-01-01

    One can hardly mention higher education today without hearing the word "innovation," or its understudies "change," "reinvention," "transformation." Last summer the National Governors Association opened its meeting with a plenary session on higher education, innovation, and economic growth. But there is nothing funny about the need for innovation…

  12. Econometric Studies of Higher Education.

    ERIC Educational Resources Information Center

    Ehrenberg, Ronald G.

    The econometrics of higher education emerged from the development of human capital theory and efforts to estimate rates of return to education in the 1960s and 1970s. This paper surveys the various strands of the literature on the econometrics of higher education that have developed during the last 40 years and indicates how a collection of papers…

  13. Higher Education Funding in Missouri

    ERIC Educational Resources Information Center

    Mueller, Lori

    2011-01-01

    The purpose of this qualitative case study was to examine perceptions of state legislators regarding funding of public higher education in the State of Missouri. To this end, I sought to determine how Missouri legislators perceive the purpose of higher education and the role the state government should play in funding it. The concept that higher…

  14. Unexploited Efficiencies in Higher Education

    ERIC Educational Resources Information Center

    Eyring, Henry C.

    2011-01-01

    In "Unexploited Efficiencies in Higher Education," Henry C. Eyring, a junior majoring in Economics at Brigham Young University-Idaho, argues that one way that the U.S. can compete globally in college attainment is to decrease cost-per-graduate. He explains how many stakeholders in higher education stand to benefit from unexploited…

  15. Assessment Issues in Higher Education.

    ERIC Educational Resources Information Center

    Atkins, M. J.; And Others

    This report reviews assessment issues from a British perspective with particular regard to the implications that the National Vocational Qualification (NVQ) Framework will have for assessment in higher education. It considers assessment in relation to the various purposes of higher education and puts forward a number of practical suggestions for…

  16. Higher Education: An International Perspective.

    ERIC Educational Resources Information Center

    Phelps, Richard P.; Dietrich, Greta L.; Phillips, Gabriele; McCormack, Kevin A.

    This report provides a review of higher education systems in selected developed countries and compares higher education in the United States and other countries. The report draws on data from the Indicators of National Education Systems Project of the Centre for Educational Research and Innovation (CERI) of the Organisation for Economic…

  17. Strategy Process in Higher Education

    ERIC Educational Resources Information Center

    Kettunen, Juha

    2010-01-01

    Higher education institutions educate those who are the most talented and best able to secure the future for the next generation. This study examines an efficient strategy process in higher education and emphasises the importance of sufficient dialogue during the process. The study describes the strategy process of the Turku University of Applied…

  18. Higher Education in the Netherlands.

    ERIC Educational Resources Information Center

    de Moor, R. A.

    There are two sectors of higher education in the Netherlands: the universities covered by the University Education Act and the vocationally-oriented colleges covered by the Further Education Act. Following a summary of the main elements of secondary education, higher or tertiary education is defined. Thirteen universities and non-university…

  19. Minority Access to Higher Education

    ERIC Educational Resources Information Center

    Jackson, Nathaniel

    2012-01-01

    Blacks, Hispanics, Native Americans, and Asian Americans are entitled to equal access to all institutions of higher education. Ensuring greater access and participation by minorities in higher education is one of the most practical ways of moving America closer to the ideal of equal opportunity, which is the actualization of the American dream.…

  20. Does Higher Education Need Deschooling?

    ERIC Educational Resources Information Center

    Butson, Russell

    2011-01-01

    This paper presents an attempt to overcome the contemporary obsession with "learning" and proposes that current practices in higher education are aligned too closely with the educational theories and practices developed within pre-university compulsory education. The author takes the position that higher education is substantially different from…

  1. Feminist Research in Higher Education

    ERIC Educational Resources Information Center

    Ropers-Huilman, Rebecca; Winters, Kelly T.

    2011-01-01

    This essay provides an overview of feminist methodology and its potential to enhance the study of higher education. Foregrounding the multiple purposes and research relationships developed through feminist research, the essay urges higher education scholars to engage feminist theories, epistemologies, and methods to inform policy, research, and…

  2. Additive manufacturing of RF absorbers

    NASA Astrophysics Data System (ADS)

    Mills, Matthew S.

    The ability of additive manufacturing techniques to fabricate integrated electromagnetic absorbers tuned for specific radio frequency bands within structural composites allows for unique combinations of mechanical and electromagnetic properties. These composites and films can be used for RF shielding of sensitive electromagnetic components through in-plane and out-of-plane RF absorption. Structural composites are a common building block of many commercial platforms. These platforms may be placed in situations in which there is a need for embedded RF absorbing properties along with structural properties. Instead of adding radar absorbing treatments to the external surface of existing structures, which adds increased size, weight and cost; it could prove to be advantageous to integrate the microwave absorbing properties directly into the composite during the fabrication process. In this thesis, a method based on additive manufacturing techniques of composites structures with prescribed electromagnetic loss, within the frequency range 1 to 26GHz, is presented. This method utilizes screen printing and nScrypt micro dispensing to pattern a carbon based ink onto low loss substrates. The materials chosen for this study will be presented, and the fabrication technique that these materials went through to create RF absorbing structures will be described. The calibration methods used, the modeling of the RF structures, and the applications in which this technology can be utilized will also be presented.

  3. Fuel Additives: Canada bans MMT

    SciTech Connect

    Sissell, K.

    1997-04-16

    The Canadian Senate voted late last week to ban use of the manganese-based fuel additive MMT, produced only in the US by Ethyl. MMT, which has been sold in Canada for the past 20 years and accounts for about half of Ethyl`s Canadian sales, has been criticized by environmentalists, who have raised public health concerns, and automakers, who say it harms emission control systems. {open_quotes}Canada`s vote is a great victory for public health and the environment,{close_quotes} says Environmental Defense Fund executive director Fred Krupp. {open_quotes}The US should move swiftly to follow suit and suspend sales of MMT until adequate toxicity testing on the additive is completed.{close_quotes} EPA had refused to approve MMT for sale because of health concerns but was compelled to do so by a December 1995 court ruling. Ethyl asserts the ban violates Canada`s obligations under Nafta and says it will file a damage claim with the Nafta arbitration panel.

  4. 40 CFR 725.950 - Additional recordkeeping requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional Procedures for Reporting on Significant New Uses of Microorganisms § 725.950 Additional recordkeeping requirements. Persons submitting a MCAN for a significant new use of a microorganism must comply with...

  5. 40 CFR 725.950 - Additional recordkeeping requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional Procedures for Reporting on Significant New Uses of Microorganisms § 725.950 Additional recordkeeping requirements. Persons submitting a MCAN for a significant new use of a microorganism must comply with...

  6. 40 CFR 725.950 - Additional recordkeeping requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional Procedures for Reporting on Significant New Uses of Microorganisms § 725.950 Additional recordkeeping requirements. Persons submitting a MCAN for a significant new use of a microorganism must comply with...

  7. 40 CFR 725.950 - Additional recordkeeping requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional Procedures for Reporting on Significant New Uses of Microorganisms § 725.950 Additional recordkeeping requirements. Persons submitting a MCAN for a significant new use of a microorganism must comply with...

  8. 40 CFR 725.950 - Additional recordkeeping requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional Procedures for Reporting on Significant New Uses of Microorganisms § 725.950 Additional recordkeeping requirements. Persons submitting a MCAN for a significant new use of a microorganism must comply with...

  9. Bubble formation in additive manufacturing of glass

    NASA Astrophysics Data System (ADS)

    Luo, Junjie; Gilbert, Luke J.; Peters, Daniel C.; Bristow, Douglas A.; Landers, Robert G.; Goldstein, Jonathan T.; Urbas, Augustine M.; Kinzel, Edward C.

    2016-05-01

    Bubble formation is a common problem in glass manufacturing. The spatial density of bubbles in a piece of glass is a key limiting factor to the optical quality of the glass. Bubble formation is also a common problem in additive manufacturing, leading to anisotropic material properties. In glass Additive Manufacturing (AM) two separate types of bubbles have been observed: a foam layer caused by the reboil of the glass melt and a periodic pattern of bubbles which appears to be unique to glass additive manufacturing. This paper presents a series of studies to relate the periodicity of bubble formation to part scan speed, laser power, and filament feed rate. These experiments suggest that bubbles are formed by the reboil phenomena why periodic bubbles result from air being trapped between the glass filament and the substrate. Reboil can be detected using spectroscopy and avoided by minimizing the laser power while periodic bubbles can be avoided by a two-step laser melting process to first establish good contact between the filament and substrate before reflowing the track with higher laser power.

  10. Iodine addition using triiodide solutions

    NASA Technical Reports Server (NTRS)

    Rutz, Jeffrey A.; Muckle, Susan V.; Sauer, Richard L.

    1992-01-01

    The study develops: a triiodide solution for use in preparing ground service equipment (GSE) water for Shuttle support, an iodine dissolution method that is reliable and requires minimal time and effort to prepare, and an iodine dissolution agent with a minimal concentration of sodium salt. Sodium iodide and hydriodic acid were both found to dissolve iodine to attain the desired GSE iodine concentrations of 7.5 +/- 2.5 mg/L and 25 +/- 5 mg/L. The 1.75:1 and 2:1 sodium iodide solutions produced higher iodine recoveries than the 1.2:1 hydriodic acid solution. A two-hour preparation time is required for the three sodium iodide solutions. The 1.2:1 hydriodic acid solution can be prepared in less than 5 min. Two sodium iodide stock solutions (2.5:1 and 2:1) were found to dissolve iodine without undergoing precipitation.

  11. Influence of nutrient additions on cadmium bioaccumulation by aquatic invertebrates in littoral enclosures

    SciTech Connect

    Currie, R.S.; Muir, D.C.G.; Fairchild, W.L.; Holoka, M.H.; Hecky, R.E.

    1998-12-01

    Cadmium distribution and bioaccumulation were examined over a 2-year period (1991--1992) in two nutrient-enriched and two control littoral enclosures and in the littoral zone in Lake 382 (L382). Lake 382, a small oligotrophic lake, is located within the Experimental Lakes Area in northwestern Ontario, Canada, and received experimental Cd additions from 1987 to 1992. In the second year of this study, chlorophyll a and suspended C concentrations in the nutrient-enriched enclosures increased by 6.6 and 3.4 times, respectively, compared to the controls. As a result of increased particulate produced by the nutrient additions, Cd concentrations in water from the nutrient-enriched enclosures were higher compared to the controls. Estimated Cd/C concentrations in water were lower in the nutrient-enriched enclosures relative to the controls because of higher particle concentrations. Effects on Cd bioaccumulation were limited even though mesotrophic to eutrophic conditions were reached in the nutrient-enriched enclosures had consistently higher Cd concentrations compared to the controls, but significant differences were not detected. Enhanced accumulation of Cd-rich particulate matter by these organisms may account for this trend. Mussels and crayfish accumulated significantly more Cd when exposed in the lake compared to the enclosures. This observation is due to elevated Cd water concentrations in the lake compared to the enclosures because of continued Cd additions to the lake. These results suggest that the water route of exposure is an important pathway for Cd accumulation by these organisms.

  12. On higher holonomy invariants in higher gauge theory II

    NASA Astrophysics Data System (ADS)

    Zucchini, Roberto

    2016-06-01

    This is the second of a series of two technical papers devoted to the analysis of holonomy invariants in strict higher gauge theory with end applications in higher Chern-Simons theory. We provide a definition of trace over a crossed module to yield surface knot invariants upon application to 2-holonomies. We show further that the properties of the trace are best described using the theory quandle crossed modules.

  13. Astrobiological Significance of Microbial Extremophiles

    NASA Technical Reports Server (NTRS)

    Pikuta, Elena V.; Hoover, Richard B.

    2007-01-01

    The microflora of the cryosphere of planet Earth provides the best analogs for life forms that might be found in the permafrost or polar ice caps of Mars, near the surface of the cometary nuclei, or in the liquid water beneath and the ice crusts of icy moons of Jupiter and Saturn. The importance of study alkaliphilic microorganisms for astrobiology was enhanced by the findings of abundant carbonates and carbonate globules rimmed with possibly biogenic magnetites in association with the putative microfossils in the ALH84001 meteorite. Although the ALH84001 "nanofossils" were to small and simple to be unambiguously recognized as biogenic, they stimulated Astrobiology research and studies of microbial extremophiles and biomarkers in ancient rocks and meteorites. Recent studies of CI and CM carbonaceous meteorites have resulted in the detection of the well-preserved mineralized remains of coccoidal and filamentous microorganisms in cyanobacterial mats. Energy Dispersive X-ray Analysis has shown anomalous biogenic element ratios clearly indicating they are not recent biological contaminants. This paper reviews microbial extremophiles in context of their significance to Astrobiology. The study of halophilic microorganisms was started from work with saline soils and lakes, and one of the record of good growth for Haloferax mediterranei was shown at 30 percent NaC1. Although alkali-tolerant nitrifying bacteria had previously been reported, the first described alkaliphilic microorganism was the bacterium Streptococcus faecalis. Halophilic and alkaliphilic forms are relevant to conditions that might be found in closed impact basins and craters on Mars filled with evaporite deposits. The first obligately acidophilic bacterium described was Acidithiobacillus ferrooxydans (formally Thiobacillus ferrooxidans). Later thermophilic lithotrophic acidophiles were found, and the hyperacidophilic moderately thermophilic species of the genus Picrophilus were found to grow at negative p

  14. Alcohol intoxication in road traffic accidents leads to higher impact speed difference, higher ISS and MAIS, and higher preclinical mortality.

    PubMed

    Stübig, Timo; Petri, Maximilian; Zeckey, Christian; Brand, Stephan; Müller, Christian; Otte, Dietmar; Krettek, Christian; Haasper, Carl

    2012-11-01

    Alcohol is one of the most important personal risk factors for serious and fatal injuries, contributing to approximately one third of all deaths from accidents. It is also described that alcohol intoxication leads to a higher mortality in the clinical course. In this study, we hypothesized that alcohol intoxication leads to different accident kinematics, a higher ISS (Injury Severity Score), and higher preclinical mortality compared to sober patients. A technical and medical investigation of alcohol intoxicated road users was performed on the scene of the crash and at the primary admitting hospital. Alcohol testing was performed with either breath alcohol tests or measurement of blood alcohol concentration (BAC) in a standard laboratory test. Between 1999 and 2010, 37,635 road traffic accidents were evaluated by the Accident Research Unit. Overall 20,741 patients were injured, 2.3% of the patients were killed. Among the injured patients, 2.2% with negative BAC were killed, compared to 4.6% fatal injuries in patients with a positive BAC (p < 0.0001). Of the patients with a positive BAC, 8.0% were severely injured, compared to 3.6% in the BAC negative group (p < 0.0001). Regarding the relative speed at impact (Δv for motorized drivers, vehicle collision speed for pedestrians and bikers), there was a significant higher difference for BAC positive patients (30 ± 20) compared to the BAC negative patients (25 ± 19, p < 0.0001). Alcohol intoxication in trauma patients leads to higher preclinical mortality, higher impact speed difference, and higher injury severity. The subgroup analysis for different alcohol concentrations shows no difference in ISS, MAIS, and relative speed, but a correlation of increasing age of patients with higher alcohol concentrations.

  15. Alcohol intoxication in road traffic accidents leads to higher impact speed difference, higher ISS and MAIS, and higher preclinical mortality.

    PubMed

    Stübig, Timo; Petri, Maximilian; Zeckey, Christian; Brand, Stephan; Müller, Christian; Otte, Dietmar; Krettek, Christian; Haasper, Carl

    2012-11-01

    Alcohol is one of the most important personal risk factors for serious and fatal injuries, contributing to approximately one third of all deaths from accidents. It is also described that alcohol intoxication leads to a higher mortality in the clinical course. In this study, we hypothesized that alcohol intoxication leads to different accident kinematics, a higher ISS (Injury Severity Score), and higher preclinical mortality compared to sober patients. A technical and medical investigation of alcohol intoxicated road users was performed on the scene of the crash and at the primary admitting hospital. Alcohol testing was performed with either breath alcohol tests or measurement of blood alcohol concentration (BAC) in a standard laboratory test. Between 1999 and 2010, 37,635 road traffic accidents were evaluated by the Accident Research Unit. Overall 20,741 patients were injured, 2.3% of the patients were killed. Among the injured patients, 2.2% with negative BAC were killed, compared to 4.6% fatal injuries in patients with a positive BAC (p < 0.0001). Of the patients with a positive BAC, 8.0% were severely injured, compared to 3.6% in the BAC negative group (p < 0.0001). Regarding the relative speed at impact (Δv for motorized drivers, vehicle collision speed for pedestrians and bikers), there was a significant higher difference for BAC positive patients (30 ± 20) compared to the BAC negative patients (25 ± 19, p < 0.0001). Alcohol intoxication in trauma patients leads to higher preclinical mortality, higher impact speed difference, and higher injury severity. The subgroup analysis for different alcohol concentrations shows no difference in ISS, MAIS, and relative speed, but a correlation of increasing age of patients with higher alcohol concentrations. PMID:22819121

  16. Additives in fibers and fabrics.

    PubMed

    Barker, R H

    1975-06-01

    The additives and contaminants which occur in textile fibers vary widely, depending on the type of fiber and the pretreatment which it has received. Synthetic fibers such as nylon and polyester contain trace amounts of contaminants such as catalysts and catalyst deactivators which remain after the synthesis of the basic polymers. In addition, there are frequently a number of materials which are added to perform specific functions in almost all man-made fibers. Examples of these would include traces of metals or metal salts used as tracers for identification of specific lots of fiber, TiO2 or similar materials added as delustrants, and a host of organic species added for such special purposes as antistatic agents or flame retardants. There may also be considerable quantities of residual monomer or small oligomers dissolved in the polymer matrix. The situation becomes even more complex after the fibers are converted into fabric form. Numerous materials are applied at various stages of fabric preparation to act as lubricants, sizing agents, antistats, bleaches, and wetting agents to facilitate the processing, but these are normally removed before the fabric reaches the cutters of the ultimate consumers and therefore usually do not constitute potential hazards. However, there are many other chemical agents which are frequently added during the later stages of fabric preparation and which are not designed to be removed. Aside from dyes and printing pigments, the most common additive for apparel fabrics is a durable press treatment. This generally involves the use of materials capable of crosslinking cellulosics by reacting through such functions as N-methylolated amides or related compounds such as ureas and carbamates. These materials pose some potential hazards due to both the nitrogenous bases and the formaldehyde which they usually release. There is usually also some residual catalyst in fabrics which have received such treatments. Other types of chemical treatments

  17. Additives in fibers and fabrics.

    PubMed Central

    Barker, R H

    1975-01-01

    The additives and contaminants which occur in textile fibers vary widely, depending on the type of fiber and the pretreatment which it has received. Synthetic fibers such as nylon and polyester contain trace amounts of contaminants such as catalysts and catalyst deactivators which remain after the synthesis of the basic polymers. In addition, there are frequently a number of materials which are added to perform specific functions in almost all man-made fibers. Examples of these would include traces of metals or metal salts used as tracers for identification of specific lots of fiber, TiO2 or similar materials added as delustrants, and a host of organic species added for such special purposes as antistatic agents or flame retardants. There may also be considerable quantities of residual monomer or small oligomers dissolved in the polymer matrix. The situation becomes even more complex after the fibers are converted into fabric form. Numerous materials are applied at various stages of fabric preparation to act as lubricants, sizing agents, antistats, bleaches, and wetting agents to facilitate the processing, but these are normally removed before the fabric reaches the cutters of the ultimate consumers and therefore usually do not constitute potential hazards. However, there are many other chemical agents which are frequently added during the later stages of fabric preparation and which are not designed to be removed. Aside from dyes and printing pigments, the most common additive for apparel fabrics is a durable press treatment. This generally involves the use of materials capable of crosslinking cellulosics by reacting through such functions as N-methylolated amides or related compounds such as ureas and carbamates. These materials pose some potential hazards due to both the nitrogenous bases and the formaldehyde which they usually release. There is usually also some residual catalyst in fabrics which have received such treatments. Other types of chemical treatments

  18. Control of Microthrix parvicella by aluminium salts addition.

    PubMed

    Durban, N; Juzan, L; Krier, J; Gillot, S

    2016-01-01

    Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella.

  19. Predicting the impact of biochar additions on soil hydraulic properties

    NASA Astrophysics Data System (ADS)

    Spokas, Kurt; Lim, Tae Jun; Feyereisen, Gary; Novak, Jeff

    2015-04-01

    Different physical and chemical properties of biochar, which is made out of a variety of biomass materials, can impact water movement through amended soil. The objective of this research was to develop a decision support tool predicting the impact of biochar additions on soil saturated hydraulic conductivity (Ksat). Four different kinds of biochar were added to four different textured soils (coarse sand, fine sand, loam, and clay texture) to assess these effects at the rates of 0, 1, 2, and 5 % (w/w). The Ksat of the biochar amended soils were significantly influenced by the rate and type of biochar, as well as the original particle size of soil. The Ksat decreased when biochar was added to coarse and fine sands. Biochar with larger particles sizes (60%; >1 mm) decreased Ksat to a larger degree than the smaller particle size biochar (60%; <1 mm) in the two sandy textured soils. Increasing tortuosity in the amended sandy soil could explain this behavior. On the other hand, for the clay loam 1% and 2% biochar additions universally increased the Ksat with higher biochar amounts providing no further alterations. The developed model utilizes soil texture pedotransfer functions for predicting agricultural soil Ksat as a function of soil texture. The model accurately predicted the direction of the Ksat influence, even though the exact magnitude still requires further refinement.

  20. Control of Microthrix parvicella by aluminium salts addition.

    PubMed

    Durban, N; Juzan, L; Krier, J; Gillot, S

    2016-01-01

    Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella. PMID:26819398

  1. [Immunogenicity of additional varicella vaccination 3-5 years after the initial vaccination].

    PubMed

    Ozaki, Takao; Nishimura, Naoko; Gotoh, Kensei; Funahashi, Keiji; Yoshii, Hironori; Okuno, Yoshinobu

    2013-07-01

    Additional varicella vaccination was carried out targeting 16 subjects who had immune adherence hemagglutination (IAHA) seroconversion following the initial varicella vaccination and did not contract breakthrough varicella after the initial vaccination. The median ages at the initial and additional vaccination were 2.1 (1.1-6.9) years old and 6.1 (4.4-10.5) years old, respectively. The mean interval between the initial and additional vaccination was 4.0 (3.2-5.2) years. IAHA and glycoprotein-based enzyme-linked immunosorbent assay (gpELISA) antibody titers were measured just before and 4-6 weeks after the additional vaccination. Side reaction was surveyed at four weeks after the additional vaccination, and compared with the results at the initial vaccination. IAHA and gpELISA seroconversion rates at the initial vaccination were 100% and 88% respectively. Prior to the additional vaccination, IAHA antibody titers significantly decreased in 50% of the subjects, and became negative in 38% of the subjects. On the other hand, a significant increase in IAHA antibody titers was observed in 25% of the subjects, and this is assumed to be the result of a subclinical infection after the initial vaccination. The positive rate of both antibodies after the additional vaccination was 100%, the mean IAHA antibody titer (Log2) after the initial/additional vaccination in seropositive subjects was 4.6/6.5, and the mean gpELISA antibody titer (Log10) was 2.3/4.0. The mean IAHA and gpELISA antibody titers were higher after the additional vaccination than after the initial vaccination (p < 0.01, p < 0.01). This is considered to be the booster effect due to the additional vaccination. At 0-2 days after the additional vaccination, a rash at the injection site was observed in 56% of the subjects, higher than the incidence after the initial vaccination (13%) (p < 0.05), but no severe systemic side reactions were observed at either the initial or the additional vaccination. In conclusion, an

  2. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  3. An Additive Manufacturing Test Artifact

    PubMed Central

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  4. SIPSEY WILDERNESS AND ADDITIONS, ALABAMA.

    USGS Publications Warehouse

    Schweinfurth, Stanley P.; Mory, Peter C.

    1984-01-01

    On the basis of geologic, geochemical, and mineral surveys the Sipsey Wilderness and additions are deemed to have little promise for the occurrence of metallic mineral resources. Although limestone, shale, and sandstone resources that occur in the area are physically suitable for a variety of uses, similar materials are available outside the area closer to transportation routes and potential markets. A small amount of coal has been identified in the area, occurring as nonpersistent beds less than 28 in. thick. Oil and (or) natural gas resources may be present if suitable structural traps exist in the subsurface. Therefore, the area has a probable oil and gas potential. Small amounts of asphaltic sandstone and limestone, commonly referred to as tar sands, may also occur in the subsurface. 5 refs.

  5. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system.

  6. A novel addition polyimide adhesive

    NASA Technical Reports Server (NTRS)

    St.clair, T. L.; Progar, D. J.

    1981-01-01

    An addition polyimide adhesive, LARC 13, was developed which shows promise for bonding both titanium and composites for applications which require service temperatures in excess of 533 K. The LARC 13 is based on an oligomeric bis nadimide containing a meta linked aromatic diamine. The adhesive melts prior to polymerization due to its oligomeric nature, thereby allowing it to be processed at 344 kPa or less. Therefore, LARC 13 is ideal for the bonding of honeycomb sandwich structures. After melting, the resin thermosets during the cure of the nadic endcaps to a highly crosslinked system. Few volatiles are evolved, thus allowing large enclosed structures to be bonded. Preparation of the adhesive as well as bonding, aging, and testing of lap shear and honeycomb samples are discussed.

  7. Gastric cancer in New Mexico counties with significant deposits of uranium.

    PubMed

    Wilkinson, G S

    1985-01-01

    Several counties in northern New Mexico display high rates of mortality from gastric cancer. Significant differences in sex-specific, age-adjusted, average annual stomach cancer mortality rates among whites from 1970-1979 were found between counties with significant deposits of uranium compared to those without significant deposits. These results remained unchanged when either socioeconomic status or Hispanic ethnicity were considered. Additional research needs to consider individual characteristics and competing risk factors for individuals with gastric cancer in these counties. A working hypothesis is that residents of counties with significant deposits of uranium are exposed to higher-than-average environmental levels of radionuclides such as radon and radon daughters, or to trace elements such as arsenic, cadmium, selenium, and lead which are commonly found in areas with uranium deposits.

  8. Adverse reactions to food additives.

    PubMed

    Simon, R A

    1986-01-01

    There are thousands of agents that are intentionally added to the food that we consume. These include preservatives, stabilizers, conditioners, thickeners, colorings, flavorings, sweeteners, antioxidants, etc. etc. Yet only a surprisingly small number have been associated with hypersensitivity reactions. Amongst all the additives, FD&C dyes have been most frequently associated with adverse reactions. Tartrazine is the most notorious of them all; however, critical review of the medical literature and current Scripps Clinic studies would indicate that tartrazine has been confirmed to be at best only occasionally associated with flares of urticaria or asthma. There is no convincing evidence in the literature of reactivity to the other azo or nonazo dyes. This can also be said of BHA/BHT, nitrites/nitrates and sorbates. Parabens have been shown to elicit IgE mediated hypersensitivity reactions when used as pharmaceutical preservatives; however, as with the other additives noted above, ingested parabens have only occasionally been associated with adverse reactions. MSG, the cause of the 'Chinese restaurant syndrome' has only been linked to asthma in one report. Sulfiting agents used primarily as food fresheners and to control microbial growth in fermented beverages have been established as the cause of any where from mild to severe and even fatal reactions in at least 5% of the asthmatic population. Other reactions reported to follow sulfite ingestion include anaphylaxis, gastro intestinal complaints and dermatological eruptions. The prevalence of these non asthmatic reactions is unknown. The mechanism of sulfite sensitive asthma is also unknown but most likely involves hyperreactivity to inhale SO2 in the great majority of cases; however, there are reports of IgE mediated reactions and other sulfite sensitive asthmatics have been found with low levels of sulfite oxidase; necessary to oxidize endogenous sulfite to sulfate.

  9. Higher order equations of motion and gravity

    NASA Astrophysics Data System (ADS)

    Lämmerzahl, Claus; Rademaker, Patricia

    2012-12-01

    Standard fundamental equations of motion for point particles are of second order in the time derivative. Here we are exploring the consequences of fundamental equations of motion with an additional small even higher order term to the standard formulation. This is related to two issues: (i) higher order equations of motion will have influence on the definition of the structure of possible interactions and in particular of the gravitational interaction, and (ii) such equations of motion provide a framework to test the validity of Newton’s second law which is the basis for the definition of forces but which assumes from the very beginning that the fundamental equations of motion are of second order. We will show that starting with our generalized equations of motions it is possible to introduce the space-time metric describing the gravitational interaction by means of a standard gauge principle. Another main result within our model of even higher order derivatives is that for slowly varying and smooth fields the higher order derivatives either lead to runaway solutions or induces a zitterbewegung. We confront this higher order scheme with experimental data.

  10. Higher order BLG supersymmetry transformations from 10-dimensional super Yang Mills

    NASA Astrophysics Data System (ADS)

    Hall, John; Low, Andrew

    2014-06-01

    We study a Simple Route for constructing the higher order Bagger-Lambert-Gustavsson theory - both supersymmetry transformations and Lagrangian - starting from knowledge of only the 10-dimensional Super Yang Mills Fermion Supersymmetry transformation. We are able to uniquely determine the four-derivative order corrected supersymmetry transformations, to lowest non-trivial order in Fermions, for the most general three-algebra theory. For the special case of Euclidean three-algbera, we reproduce the result presented in arXiv:1207.1208, with significantly less labour. In addition, we apply our method to calculate the quadratic fermion terms in the higher order BLG fermion supersymmetry transformation.

  11. Higher-order ionosphere modeling for CODE's next reprocessing activities

    NASA Astrophysics Data System (ADS)

    Lutz, S.; Schaer, S.; Meindl, M.; Dach, R.; Steigenberger, P.

    2009-12-01

    CODE (the Center for Orbit Determination in Europe) is a joint venture between the Astronomical Institute of the University of Bern (AIUB, Bern, Switzerland), the Federal Office of Topography (swisstopo, Wabern, Switzerland), the Federal Agency for Cartography and Geodesy (BKG, Frankfurt am Main, Germany), and the Institut für Astronomische und Phsyikalische Geodäsie of the Technische Universität München (IAPG/TUM, Munich, Germany). It acts as one of the global analysis centers of the International GNSS Service (IGS) and participates in the first IGS reprocessing campaign, a full reanalysis of GPS data collected since 1994. For a future reanalyis of the IGS data it is planned to consider not only first-order but also higher-order ionosphere terms in the space geodetic observations. There are several works (e.g. Fritsche et al. 2005), which showed a significant and systematic influence of these effects on the analysis results. The development version of the Bernese Software used at CODE is expanded by the ability to assign additional (scaling) parameters to each considered higher-order ionosphere term. By this, each correction term can be switched on and off on normal-equation level and, moreover, the significance of each correction term may be verified on observation level for different ionosphere conditions.

  12. Functional Significance of Serotonin Receptor Dimerization

    PubMed Central

    Herrick-Davis, Katharine

    2013-01-01

    The original model of G protein activation by a single G-protein-coupled receptor (GPCR) is giving way to a new model wherein two protomers of a GPCR dimer interact with a single G protein. This article will review the evidence suggesting that 5-HT receptors form dimers/oligomers and will compare the findings with results obtained from studies with other biogenic amine receptors. Topics to be covered include the origin or biogenesis of dimer formation, potential dimer interface(s), and oligomer size (dimer versus tetramer or higher order). The functional significance will be discussed in terms of G-protein activation following ligand binding to one or two protomers in a dimeric structure, the formation of heterodimers and the development of bivalent ligands. PMID:23811735

  13. [Pathogenesis and significance of diabetic dyslipidemia].

    PubMed

    Zeman, M; Zák, A

    2004-01-01

    Patients with type 2 diabetes mellitus are at the higher risk of development of on arteriosclerosis based cardiovascular diseases. Epidemiological studies have shown that diabetic dislipidemia with hypertriglyceridemia, presence of small dense LDL subfraction, low concentration of HDL-cholesterol and increased postprandial lipemia can represent a serious threat. Several studies have found significant decrease of cardiovascular morbidity and mortality after a treatment of diabetic dislipidemia, namely by statins and fibrates. Contemporary therapeutic algorhithms of European and American professional societies for the hyperlipidemia treatment classify diabetes mellitus as an equivalent of already developed complication of atherosclerosis. Our article presents pathophysiology of the diabetic dislipidemia, recommended target values of pasma lipids in diabetic patients and an overview of present possibilities of pharmacotherapy of the diabetic dislipidemia.

  14. Significance of Adult Pedestrian Torso Injury

    PubMed Central

    Ivarsson, B. Johan; Henary, Basem; Crandall, Jeff R.; Longhitano, Douglas

    2005-01-01

    The current paper uses data from two trauma registries to evaluate the significance of adult pedestrian torso injury relative to head and lower extremity injuries and to determine the relative importance of injuries to individual torso organs/structures. Analyses are conducted with and without adjusting for striking vehicle body type (car versus LTV). Although the incidence of torso injury is approximately 50% higher in pedestrians struck by LTVs than in those struck by cars, torso injury appears to be as an important contributor to the overall cost of pedestrian morbidity as is lower extremity injury. The most frequently injured torso organs/structures include the rib cage, lung & pleura, and liver. The results indicate a need for an increased focus on the prevention of torso injury in the design of pedestrian safety countermeasures. PMID:16179153

  15. Higher and sub-harmonic Lamb wave mode generation due to debond-induced contact nonlinearity

    NASA Astrophysics Data System (ADS)

    Guha, Anurup; Bijudas, C. R.

    2016-04-01

    Non-cumulative higher and sub-harmonic Lamb wave mode generation as a result of partial-debond of piezoelectric wafer transducers (PWT) bonded onto an Aluminium plate, is numerically investigated and experimentally validated. The influence of excitation frequency on the extent of nonlinearity due to clapping mechanism of the partially-debonded PWTs is discussed. A set of specific frequency range is arrived at based on the Eigen-value and Harmonic analyses of PWTs used in the model. It is found that, at these frequencies, which are integral multiple of the first width-direction mode of a PWT, significantly higher amplitudes of higher-harmonics are observed. It is also seen that at specific debond-positions and lengths, sharp sub-harmonics in addition to higher-harmonics are present. Signal processing is carried out using Fast Fourier transform, which is normalized for comparisons.

  16. Additional technician tasks and turnaround time in the clinical Stat laboratory

    PubMed Central

    Salinas, Maria; López-Garrigós, Maite; Flores, Emilio; Leiva-Salinas, Maria; Lillo, Rosa; Leiva-Salinas, Carlos

    2016-01-01

    Introduction Many additional tasks in the Stat laboratory (SL) increase the workload. It is necessary to control them because they can affect the service provided by the laboratory. Our aim is to calculate these tasks, study their evolution over a 10 year period, and compare turnaround times (TAT) in summer period to the rest of the year. Materials and methods Additional tasks were classified as “additional test request” and “additional sample”. We collected those incidences from the laboratory information system (LIS), and calculated their evolution over time. We also calculated the monthly TAT for troponin for Emergency department (ED) patients, as the difference between the verification and LIS registration time. A median time of 30 minutes was our indicator target. TAT results and tests workload in summer were compared to the rest of the year. Results Over a 10-year period, the technologists in the SL performed 51,385 additional tasks, a median of 475 per month. The workload was significantly higher during the summer (45,496 tests) than the rest of the year (44,555 tests) (P = 0.019). The troponin TAT did not show this variation between summer and the rest of the year, complying always with our 30 minutes indicator target. Conclusion The technicians accomplished a significant number of additional tasks, and the workload kept increasing over the period of 10 years. That did not affect the TAT results. PMID:27346970

  17. Thatcherism and British Higher Education.

    ERIC Educational Resources Information Center

    Shattock, Michael

    1989-01-01

    A discussion of the influence of Britain's prime minister, Margaret Thatcher, on higher education looks at the relationship between the administrator's 10 years in office and the fiscal, educational, and public policy issues currently under debate. (MSE)

  18. Synthesis of higher monocarboxylic acids

    SciTech Connect

    Taikov, B.F.; Novakovskii, E.M.; Zhelkovskaya, V.P.; Shadrova, V.N.; Shcherbik, P.K.

    1981-01-01

    Brown-coal and peat waxes contain higher monocarboxylic acids, alcohols and esters of them as their main components. In view of this, considerable interest is presented by the preparation of individual compounds among those mentioned above, which is particularly important in the study of the composition and development of the optimum variants of the chemical processing of the waxes. In laboratory practice, to obtain higher monocarboxylic acids use is generally made of electrosynthesis according to Kolbe which permits unbranched higher aliphatic acids with given lengths of the hydrocarbon chain to be obtained. The aim of the present work was to synthesize higher monocarboxylic acids: arachidic, behenic, lignoceric, pentacosanoic, erotic, heptacosanoic, montanic, nonacosanoic, melissic, dotriacontanoic and tetratriacontanoic, which are present in waxes. Characteristics of synthesized acids are tabulated. 20 refs.

  19. Solving higher curvature gravity theories

    NASA Astrophysics Data System (ADS)

    Chakraborty, Sumanta; SenGupta, Soumitra

    2016-10-01

    Solving field equations in the context of higher curvature gravity theories is a formidable task. However, in many situations, e.g., in the context of f( R) theories, the higher curvature gravity action can be written as an Einstein-Hilbert action plus a scalar field action. We show that not only the action but the field equations derived from the action are also equivalent, provided the spacetime is regular. We also demonstrate that such an equivalence continues to hold even when the gravitational field equations are projected on a lower-dimensional hypersurface. We have further addressed explicit examples in which the solutions for Einstein-Hilbert and a scalar field system lead to solutions of the equivalent higher curvature theory. The same, but on the lower-dimensional hypersurface, has been illustrated in the reverse order as well. We conclude with a brief discussion on this technique of solving higher curvature field equations.

  20. Higher Education: Labor Market Linkage.

    ERIC Educational Resources Information Center

    Asayeghn, Desta

    1982-01-01

    Examines the methodology of three case studies investigating the linkage between higher education and the world of work in the Sudan, Zambia, and Tanzania. Summarizes 12 main findings. Suggests the studies remain traditional human resources planning efforts. (NEC)

  1. Effect of additional surgery after noncurative endoscopic submucosal dissection for early gastric cancer

    PubMed Central

    Yamanouchi, Kohei; Ogata, Shinichi; Sakata, Yasuhisa; Tsuruoka, Nanae; Shimoda, Ryo; Nakayama, Atsushi; Akutagawa, Takashi; Shirai, Shimpei; Takeshita, Eri; Yamamoto, Koji; Fujimoto, Kazuma; Iwakiri, Ryuichi

    2016-01-01

    Background and study aims: Endoscopic submucosal dissection (ESD) is a standard treatment for early gastric cancer (EGC) without lymph node metastasis. However, some patients undergo noncurative ESD. The aim of the present study was to assess the long-term clinical outcomes of noncurative ESD with or without additional surgery. Patients and methods: We investigated the chart data from all patients who had undergone ESD for EGC at Saga Medical School Hospital and Saga Prefectural Medical Centre Koseikan between 2001 and 2012. A total of 957 cases (1047 lesions) of EGC underwent ESD, and 99 had noncurative ESD. In total, 20 cases were excluded because their follow-up period was < 3 years. We divided the patients into observation and additional surgery groups, and we compared the survival rate and related factors between the groups. Results: After noncurative ESD, 28 /79 patients (35.4 %) underwent additional surgery and 51/79 (64.6 %) were followed up without surgery. The average age of patients in the observation group was higher than that of the additional surgery group (75.9 vs. 71.6 years; P = 0.03). The incidence of hypertension was significantly higher in the observation group compared with the additional surgery group (51.0 vs. 25.9 %; P = 0.03). The overall survival rate of the additional surgery group was longer than that of the observation group. However, only one patient died from gastric cancer in the observation group. The disease-specific survival rate did not differ significantly between the groups. Conclusions: It might be acceptable to follow up without additional surgery for some patients with comorbidity and who were elderly after noncurative ESD for EGC. PMID:26793781

  2. Additional Post-Concussion Impact Exposure May Affect Recovery in Adolescent Athletes.

    PubMed

    Terwilliger, Virginia K; Pratson, Lincoln; Vaughan, Christopher G; Gioia, Gerard A

    2016-04-15

    Repeat concussion has been associated with risk for prolonged and pronounced clinical recovery in athletes. In this study of adolescent athletes, we examined whether an additional head impact within 24 h of a sports-related concussion (SRC) is associated with higher symptom burden and prolonged clinical recovery compared with a single-injury group. Forty-two student-athletes (52% male, mean age = 14.9 years) diagnosed with an SRC in a concussion clinic were selected for this study: (1) 21 athletes who sustained an additional significant head impact within 24 h of the initial injury (additional-impact group); (2) 21 single-injury athletes, age and gender matched, who sustained only one discrete concussive blow to the head (single-injury group). Groups did not differ on initial injury characteristics or pre-injury risk factors. The effect of injury status (single- vs. additional-impact) was examined on athlete- and parent-reported symptom burden (at first clinic visit) and length of recovery (LOR). Higher symptom burden was reported by the athletes and parents in the additional-impact group at the time of first visit. The additional-impact group also had a significantly longer LOR compared with the single-injury group. These findings provide preliminary, hypothesis-generating evidence for the importance of immediate removal from play following an SRC to protect athletes from re-injury, which may worsen symptoms and prolong recovery. The retrospective study design from a specialized clinical sample points to the need for future prospective studies of the relationship between single- and additional-impact injuries on symptom burden and LOR. PMID:26421452

  3. Additive attacks on speaker recognition

    NASA Astrophysics Data System (ADS)

    Farrokh Baroughi, Alireza; Craver, Scott

    2014-02-01

    Speaker recognition is used to identify a speaker's voice from among a group of known speakers. A common method of speaker recognition is a classification based on cepstral coefficients of the speaker's voice, using a Gaussian mixture model (GMM) to model each speaker. In this paper we try to fool a speaker recognition system using additive noise such that an intruder is recognized as a target user. Our attack uses a mixture selected from a target user's GMM model, inverting the cepstral transformation to produce noise samples. In our 5 speaker data base, we achieve an attack success rate of 50% with a noise signal at 10dB SNR, and 95% by increasing noise power to 0dB SNR. The importance of this attack is its simplicity and flexibility: it can be employed in real time with no processing of an attacker's voice, and little computation is needed at the moment of detection, allowing the attack to be performed by a small portable device. For any target user, knowing that user's model or voice sample is sufficient to compute the attack signal, and it is enough that the intruder plays it while he/she is uttering to be classiffed as the victim.

  4. Additive Transforms Paint into Insulation

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Tech Traders Inc. sought assistance developing low-cost, highly effective coatings and paints that created useful thermal reflectance and were safe and non-toxic. In cooperation with a group of engineers at Kennedy Space Center., Tech Traders created Insuladd, a powder additive made up of microscopic, inert gas-filled, ceramic microspheres that can be mixed into ordinary interior or exterior paint, allowing the paint to act like a layer of insulation. When the paint dries, this forms a radiant heat barrier, turning the ordinary house paint into heat-reflecting thermal paint. According to Tech Traders, the product works with all types of paints and coatings and will not change the coverage rate, application, or adhesion of the paint. Other useful applications include feed storage silos to help prevent feed spoilage, poultry hatcheries to reduce the summer heat and winter cold effects, and on military vehicles and ships. Tech Traders has continued its connection to the aerospace community by recently providing Lockheed Martin Corporation with one of its thermal products for use on the F-22 Raptor.

  5. Sustainability Characterization for Additive Manufacturing

    PubMed Central

    Mani, Mahesh; Lyons, Kevin W; Gupta, SK

    2014-01-01

    Additive manufacturing (AM) has the potential to create geometrically complex parts that require a high degree of customization, using less material and producing less waste. Recent studies have shown that AM can be an economically viable option for use by the industry, yet there are some inherent challenges associated with AM for wider acceptance. The lack of standards in AM impedes its use for parts production since industries primarily depend on established standards in processes and material selection to ensure the consistency and quality. Inability to compare AM performance against traditional manufacturing methods can be a barrier for implementing AM processes. AM process sustainability has become a driver due to growing environmental concerns for manufacturing. This has reinforced the importance to understand and characterize AM processes for sustainability. Process characterization for sustainability will help close the gaps for comparing AM performance to traditional manufacturing methods. Based on a literature review, this paper first examines the potential environmental impacts of AM. A methodology for sustainability characterization of AM is then proposed to serve as a resource for the community to benchmark AM processes for sustainability. Next, research perspectives are discussed along with relevant standardization efforts. PMID:26601038

  6. Sustainability Characterization for Additive Manufacturing.

    PubMed

    Mani, Mahesh; Lyons, Kevin W; Gupta, S K

    2014-01-01

    Additive manufacturing (AM) has the potential to create geometrically complex parts that require a high degree of customization, using less material and producing less waste. Recent studies have shown that AM can be an economically viable option for use by the industry, yet there are some inherent challenges associated with AM for wider acceptance. The lack of standards in AM impedes its use for parts production since industries primarily depend on established standards in processes and material selection to ensure the consistency and quality. Inability to compare AM performance against traditional manufacturing methods can be a barrier for implementing AM processes. AM process sustainability has become a driver due to growing environmental concerns for manufacturing. This has reinforced the importance to understand and characterize AM processes for sustainability. Process characterization for sustainability will help close the gaps for comparing AM performance to traditional manufacturing methods. Based on a literature review, this paper first examines the potential environmental impacts of AM. A methodology for sustainability characterization of AM is then proposed to serve as a resource for the community to benchmark AM processes for sustainability. Next, research perspectives are discussed along with relevant standardization efforts.

  7. Denitrification with carbon addition--kinetic considerations.

    PubMed

    Dold, P; Takács, I; Mokhayeri, Y; Nichols, A; Hinojosa, J; Riffat, R; Bott, C; Bailey, W; Murthy, S

    2008-05-01

    The Blue Plains Advanced Wastewater Treatment Plant (Washington, D.C.) uses methanol as an external carbon source in a postdenitrification process, to achieve low effluent total nitrogen concentrations. This becomes more difficult in winter, at lower mixed liquor temperatures and higher flows, as a consequence of the kinetic behavior of the methanol-utilizing heterotrophs. The paper reports on an experimental batch test study conducted on Blue Plains postdenitrification sludge to investigate (1) the maximum specific growth rate of methanol-utilizing heterotrophs (Mu(METH)); (2) the temperature dependency of the growth rate; and (3) the efficacy of alternate substrates (ethanol, acetate, and sugar). A limited number of tests were conducted on sludge from two other treatment plants with methanol addition. PMID:18605381

  8. Additional Crime Scenes for Projectile Motion Unit

    NASA Astrophysics Data System (ADS)

    Fullerton, Dan; Bonner, David

    2011-12-01

    Building students' ability to transfer physics fundamentals to real-world applications establishes a deeper understanding of underlying concepts while enhancing student interest. Forensic science offers a great opportunity for students to apply physics to highly engaging, real-world contexts. Integrating these opportunities into inquiry-based problem solving in a team environment provides a terrific backdrop for fostering communication, analysis, and critical thinking skills. One such activity, inspired jointly by the museum exhibit "CSI: The Experience"2 and David Bonner's TPT article "Increasing Student Engagement and Enthusiasm: A Projectile Motion Crime Scene,"3 provides students with three different crime scenes, each requiring an analysis of projectile motion. In this lesson students socially engage in higher-order analysis of two-dimensional projectile motion problems by collecting information from 3-D scale models and collaborating with one another on its interpretation, in addition to diagramming and mathematical analysis typical to problem solving in physics.

  9. Significance testing of orbital forcing in deep time

    NASA Astrophysics Data System (ADS)

    Kemp, David

    2016-04-01

    The recognition of orbitally forced (Milankovitch) climate cycles in geological archives marked a paradigm shift in Earth science, revealing a heartbeat within the climate system of general importance and key utility. Resolving orbital cycles in stratigraphic data is, however, problematic owing to the imperfect stratigraphic preservation of climate signals, the masking effects of non-periodic variance, and uncertainties in the expected responses of proxy records to climate change. Power spectral analysis is the primary tool used to facilitate identification of orbital cycles in stratigraphic data, but commonly employed methods for testing the significance of relatively high narrow-band variance of potential orbital origin in spectra have been criticised for inadequately balancing the respective probabilities of type I (false positive) and type II (false negative) errors. This has led to suggestions that the importance of orbital forcing in deep time is overstated [1]. It can be readily demonstrated, however, that the imperfect nature of the stratigraphic record sets an upper limit on the attainable significance of orbital signals. Optimised significance testing is that which minimises the sum of type I and type II errors [2]. Numerical simulations of stratigraphically preserved orbital signals suggest that optimum significance levels at which to reject a null hypothesis of no orbital forcing cluster between 99% and 99.9%. This is lower than recently advocated [1], but higher than the 90-99% levels most commonly employed in the literature. Nevertheless, in consonance with the emergent view from other scientific disciplines, fixed-value null hypothesis significance testing of power spectra is likely ill suited to verifying orbital forcing. In part, this is because the experiments also indicate that the combined probability of making an error in the acceptance or rejection of an orbital hypothesis may be rather high for typical stratigraphic data, and hence the use of

  10. Costs and Difficulties on the Way to a Higher Education

    ERIC Educational Resources Information Center

    Mogil'chak, E. L.

    2012-01-01

    A higher education continues to be a significant value to young people; this is manifested clearly in the growth of the numbers enrolled in higher educational institutions of Russia. This article examines "the process by which young people achieve their goal"--obtaining a higher education--as a set of stages linked to specific kinds of costs. The…

  11. Access to Higher Education in China: Differences in Opportunity

    ERIC Educational Resources Information Center

    Wang, Houxiong

    2011-01-01

    Access to higher education in China has opened up significantly in the move towards a mass higher education system. However, aggregate growth does not necessarily imply fair or reasonable distribution of opportunity. In fact, the expansion of higher education has a rather more complex influence on opportunity when admissions statistics are viewed…

  12. Internationalization of Higher Education in China and Its Development Direction

    ERIC Educational Resources Information Center

    Chen, Dong

    2011-01-01

    The internationalization of higher education plays an important role in education, but from the perspective of the whole society, there is a higher level of significance. Combining with foreign experience, this paper holds that internationalization of higher education in China should be established to promote international education by…

  13. Chicanas and Higher Education: Three Decades of Literature and Thought

    ERIC Educational Resources Information Center

    Cuadraz, Gloria Holguin

    2005-01-01

    The severe under representation of Chicanas in higher education reveals the need to chronicle the evolution of the field of Chicanas and higher education. This article highlights key studies and significant events related to the field of Chicanas and higher education for three decades, beginning with the 1970s and ending with the 1990s. The author…

  14. Institute of Higher Education: An Oral History (1964-2002).

    ERIC Educational Resources Information Center

    Fincher, Cameron

    This oral history is part of the celebration planned by the University of Georgia Institute of Higher Education to honor Cameron Fincher for his service to the field of higher education and the Institute. Dr, Fincher was interviewed by Delmer D. Dunn about the significant changes that have occurred in higher education over the past 50 years.…

  15. The Conditioning Role of State Higher Education Governance Structures

    ERIC Educational Resources Information Center

    Tandberg, David A.

    2013-01-01

    This article reports on a study that examined whether the presence of a consolidated governing board for higher education conditions the impact various political factors have on state support for higher education. The existence of a consolidated governing board is shown to significantly alter the politics of the state higher education…

  16. Inclusion in Higher Education: Issues in University-School Partnership

    ERIC Educational Resources Information Center

    Armstrong, D.; Cairnduff, A.

    2012-01-01

    The significant under-representation of people from low socio-economic backgrounds in higher education in Australia has been placed squarely at the front of the Australian Federal Government's higher education agenda. The barriers for students from low socio-economic backgrounds to access higher education are broad and multi-causal. The…

  17. Access and Equity in Higher Education in Antigua and Barbuda

    ERIC Educational Resources Information Center

    Hewlett-Thomas, Elsie

    2009-01-01

    Across the international higher education spectrum access represents a significant issue. The literature is replete with analyses of access in various higher education systems. Low and inequitable patterns of participation in higher education are particularly prominent in developing countries. This dissertation is a case study of the higher…

  18. Combined additive manufacturing approaches in tissue engineering.

    PubMed

    Giannitelli, S M; Mozetic, P; Trombetta, M; Rainer, A

    2015-09-01

    Advances introduced by additive manufacturing (AM) have significantly improved the control over the microarchitecture of scaffolds for tissue engineering. This has led to the flourishing of research works addressing the optimization of AM scaffolds microarchitecture to optimally trade-off between conflicting requirements (e.g. mechanical stiffness and porosity level). A fascinating trend concerns the integration of AM with other scaffold fabrication methods (i.e. "combined" AM), leading to hybrid architectures with complementary structural features. Although this innovative approach is still at its beginning, significant results have been achieved in terms of improved biological response to the scaffold, especially targeting the regeneration of complex tissues. This review paper reports the state of the art in the field of combined AM, posing the accent on recent trends, challenges, and future perspectives.

  19. The clinicopathological significance of RUNX3 hypermethylation and mRNA expression in human breast cancer, a meta-analysis

    PubMed Central

    Song, Xiao-yun; Li, Bo-yan; Zhou, En-xiang; Wu, Feng-xia

    2016-01-01

    Aberrant promoter methylation of RUNX3 has been reported in several tumors including human breast cancer (BC). However, the association between RUNX3 hypermethylation and incidence of BC remains elusive. In this study, a detailed literature search was performed in Medline and Google Scholar for related research publications. Analysis of pooled data were executed. Odds ratios with corresponding confidence intervals were determined and summarized, respectively. Finally, 13 studies were identified for the meta-analysis. Analysis of the pooled data showed that RUNX3 hypermethylation was significantly higher in both ductal carcinoma in situ and invasive ductal carcinoma (IDC) than in normal breast tissues. In addition, RUNX3 methylation was significantly higher in IDC than in benign tumor. However, RUNX3 methylation was not significantly higher in IDC than in ductal carcinoma in situ. We also determined that RUNX3 hypermethylation was significantly higher in ER positive BC than in ER negative BC. In addition, high RUNX3 mRNA expression was found to be correlated with better overall survival and relapse-free survival for all BC patients. Our results strongly support that RUNX3 hypermethylation may play an important role in BC incidence. RUNX3 methylation is a valuable early biomarker for the diagnosis of BC. Further large-scale studies will provide more insight into the role of RUNX3 hypermethylation in the carcinogenesis and clinical diagnosis of BC patients. PMID:27616890

  20. The clinicopathological significance of RUNX3 hypermethylation and mRNA expression in human breast cancer, a meta-analysis.

    PubMed

    Song, Xiao-Yun; Li, Bo-Yan; Zhou, En-Xiang; Wu, Feng-Xia

    2016-01-01

    Aberrant promoter methylation of RUNX3 has been reported in several tumors including human breast cancer (BC). However, the association between RUNX3 hypermethylation and incidence of BC remains elusive. In this study, a detailed literature search was performed in Medline and Google Scholar for related research publications. Analysis of pooled data were executed. Odds ratios with corresponding confidence intervals were determined and summarized, respectively. Finally, 13 studies were identified for the meta-analysis. Analysis of the pooled data showed that RUNX3 hypermethylation was significantly higher in both ductal carcinoma in situ and invasive ductal carcinoma (IDC) than in normal breast tissues. In addition, RUNX3 methylation was significantly higher in IDC than in benign tumor. However, RUNX3 methylation was not significantly higher in IDC than in ductal carcinoma in situ. We also determined that RUNX3 hypermethylation was significantly higher in ER positive BC than in ER negative BC. In addition, high RUNX3 mRNA expression was found to be correlated with better overall survival and relapse-free survival for all BC patients. Our results strongly support that RUNX3 hypermethylation may play an important role in BC incidence. RUNX3 methylation is a valuable early biomarker for the diagnosis of BC. Further large-scale studies will provide more insight into the role of RUNX3 hypermethylation in the carcinogenesis and clinical diagnosis of BC patients. PMID:27616890

  1. [Significant events in Polish psychiatry in 2003?].

    PubMed

    Bomba, Jacek

    2004-01-01

    The aim of this paper was a reflection on the most significant events in Polish psychiatry in 2003. Reform in health care financing and its realisation in 2003 introduced a risk of inhibiting further development of mental health care. The endangerment is a result of allocation of resources, which is inadequate to real costs and promotes in-patient treatment. An additional risk is seen in a project of privatisation of health care institutions. Increasing orientation towards methodology of molecular biology, which is similar to a general global tendency, influences research in psychiatry. Nevertheless the low number of publications resulting from government sponsored studies is disturbing. The situation in forensic psychiatry calls for involvement and studies. Psychiatria Polska published a report indicating low standard of psychiatric expertise for courts and high probability of corruption. The same was reflected in mass media publications later on. Polish Psychiatric Association Board had appointed a special commission to study this problem.

  2. Higher Education Accounting Manual. Utah Coordinating Council of Higher Education.

    ERIC Educational Resources Information Center

    Utah State Coordinating Council of Higher Education, Salt Lake City.

    Recognition of a critical need for accurate and detailed information to refine the process of budgeting funds for higher education in Utah led to the preparation of this accounting manual for universities and colleges in the state. The manual presents guidelines for the uniform accounting and reporting of financial and statistical data, and is…

  3. Higher derivative theories with constraints: exorcising Ostrogradski's ghost

    SciTech Connect

    Chen, Tai-jun; Lim, Eugene A.; Fasiello, Matteo; Tolley, Andrew J. E-mail: matte@case.edu E-mail: andrew.j.tolley@case.edu

    2013-02-01

    We prove that the linear instability in a non-degenerate higher derivative theory, the Ostrogradski instability, can only be removed by the addition of constraints if the original theory's phase space is reduced.

  4. Family Background, Financial Constraints and Higher Education Attendance in China

    ERIC Educational Resources Information Center

    Li, Wenli

    2007-01-01

    Using data from the 2004 China College Student Survey, conducted by the author, this paper finds that long-term factors such as scholastic ability and parental education are significantly correlated with higher education attendance. By contrast, short-term financial constraints are also significantly associated with higher education access, but to…

  5. The Demand for Higher Education in Turkey and Open Education

    ERIC Educational Resources Information Center

    Cekerol, Kamil

    2012-01-01

    Failure to meet considerably high demand for higher education in Turkey has always been one of the most significant concerns of Turkish Higher Education System for many years. In this respect, Anadolu University Open Education Faculty has played a significant role in the attempts to overcome this problem in Turkey for the last three decades. In…

  6. Internationalization in Higher Education in China: A Practitioner's Reflection

    ERIC Educational Resources Information Center

    Wang, Yibing

    2008-01-01

    Since higher education reforms were started in the mid-1980s, higher education in China has experienced significant transformations. Changes have not only been revealed by the increase in numbers of undergraduates, but also by a significant expansion in postgraduate education in mainland China. In order to enhance its global competitiveness, the…

  7. Novel carbon-rich additives preparation by degradative solvent extraction of biomass wastes for coke-making.

    PubMed

    Zhu, Xianqing; Li, Xian; Xiao, Li; Zhang, Xiaoyong; Tong, Shan; Wu, Chao; Ashida, Ryuichi; Liu, Wenqiang; Miura, Kouichi; Yao, Hong

    2016-05-01

    In this work, two extracts (Soluble and Deposit) were produced by degradative solvent extraction of biomass wastes from 250 to 350°C. The feasibilities of using Soluble and Deposit as additives for coke-making were investigated for the first time. The Soluble and Deposit, having significantly higher carbon content, lower oxygen content and extremely lower ash content than raw biomasses. All Solubles and most of Deposits can melt completely at the temperature ranged from 80 to 120°C and 140 to 180°C, respectively. The additions of Soluble or Deposit into the coke-making coal significantly improved their thermoplastic properties with as high as 9°C increase of the plastic range. Furthermore, the addition of Deposit or Soluble also markedly enhanced the coke quality through increasing coke strength after reaction (CSR) and reducing coke reactivity index (CRI). Therefore, the Soluble and Deposit were proved to be good additives for coke-making.

  8. Change of Higher Education in Response to European Pressures: Conceptualization and Operationalization of Europeanization of Higher Education

    ERIC Educational Resources Information Center

    Vukasovic, Martina

    2013-01-01

    This article focuses on change in higher education in response to environmental pressures, more specifically pressures coming from European integration initiatives with respect to higher education, e.g. the Bologna Process. Significant research attention has so far been focused on the supposed impact of European initiatives on higher education…

  9. Nitrogen oxide abatement by distributed fuel addition

    SciTech Connect

    Wendt, J.O.L.; Meraab, J.

    1988-03-25

    The purpose of this project is to develop techniques for nitrogen oxides abatement by distributed fuel addition. The major nitrogen oxide of interest is Nitric Oxide (NO), a precursor to premature forest damage and to acid rain. Recently interest has also been evoked with respect to an additional oxide of nitrogen, namely Nitrous Oxide (N{sub 2}O). Therefore, abatement measures for NO{sub x} are being investigated to determine their influence on N{sub 2}O as well. This report briefly describes the significance of N{sub 2}O emissions to the environment and the urgent need to develop techniques that can reduce emissions of both NO and N{sub 2}O. Reburning through distributed fuel addition may be an effective technique for NO{sub x} (mainly NO) emission control as described in the previous quarterly report. Reburning may also be effective in reducing N{sub 2}O levels. A technique for N{sub 2}O measurement by gas chromatography/electron capture detection was developed during this quarter, and is described in this report. This analysis technique will be used in the proposed experimental study to investigate the effectiveness of reburning on N{sub 2}O control.

  10. The Higher Education Clearinghouse for Space Sciences

    NASA Astrophysics Data System (ADS)

    Cobabe-Ammann, E. A.; Shipp, S. S.; Dalton, H.

    2011-12-01

    The Higher Education Clearinghouse (HECl) is a searchable database of undergraduate classroom materials for faculty teaching planetary sciences and solar and space physics at both the introductory and upper division levels. Modeled after the highly successful SERC clearinghouse for geosciences assets, HECl was designed for easy submission of classroom assets - from homeworks and computer interactives to laboratories and demonstrations. All materials are peer-reviewed before posting, and authors adhere to the Creative Commons Attribution (CC BY). HECl materials are automatically cross-posted to other digital libraries (e.g., ComPADRE) and virtual higher education communities (e.g., Connexions). In addition to classroom materials, HECl provides news and information about educational research and best practices, funding opportunities, and ongoing efforts and collaborations for undergraduate education.

  11. Cosmology with higher-derivative matter fields

    NASA Astrophysics Data System (ADS)

    Harko, Tiberiu; Lobo, Francisco S. N.; Saridakis, Emmanuel N.

    2016-06-01

    We investigate the cosmological implications of a new class of modified gravity, where the field equations generically include higher-order derivatives of the matter fields, arising from the introduction of non-dynamical auxiliary fields in the action. Imposing a flat, homogeneous and isotropic geometry, we extract the Friedmann equations, obtaining an effective dark-energy sector containing higher-derivatives of the matter energy density and pressure. For the cases of dust, radiation and stiff matter, we analyze the cosmological behavior, finding accelerating, de Sitter and non-accelerating phases, dominated by matter or dark-energy. Additionally, the effective dark-energy equation-of-state parameter can be quintessence-like, cosmological-constant-like or even phantom-like. The detailed study of these scenarios may provide signatures, that could distinguish them from other candidates of modified gravity.

  12. Thermodynamics of higher dimensional black holes

    SciTech Connect

    Accetta, F.S.; Gleiser, M.

    1986-05-01

    We discuss the thermodynamics of higher dimensional black holes with particular emphasis on a new class of spinning black holes which, due to the increased number of Casimir invariants, have additional spin degrees of freedom. In suitable limits, analytic solutions in arbitrary dimensions are presented for their temperature, entropy, and specific heat. In 5 + 1 and 9 + 1 dimensions, more general forms for these quantities are given. It is shown that the specific heat for a higher dimensional black hole is negative definite if it has only one non-zero spin parameter, regardless of the value of this parameter. We also consider equilibrium configurations with both massless particles and massive string modes. 16 refs., 3 figs.

  13. HEAT: High accuracy extrapolated ab initio thermochemistry. III. Additional improvements and overview.

    SciTech Connect

    Harding, M. E.; Vazquez, J.; Ruscic, B.; Wilson, A. K.; Gauss, J.; Stanton, J. F.; Chemical Sciences and Engineering Division; Univ. t Mainz; The Univ. of Texas; Univ. of North Texas

    2008-01-01

    Effects of increased basis-set size as well as a correlated treatment of the diagonal Born-Oppenheimer approximation are studied within the context of the high-accuracy extrapolated ab initio thermochemistry (HEAT) theoretical model chemistry. It is found that the addition of these ostensible improvements does little to increase the overall accuracy of HEAT for the determination of molecular atomization energies. Fortuitous cancellation of high-level effects is shown to give the overall HEAT strategy an accuracy that is, in fact, higher than most of its individual components. In addition, the issue of core-valence electron correlation separation is explored; it is found that approximate additive treatments of the two effects have limitations that are significant in the realm of <1 kJ mol{sup -1} theoretical thermochemistry.

  14. Analysis of economics of a TV broadcasting satellite for additional nationwide TV programs

    NASA Technical Reports Server (NTRS)

    Becker, D.; Mertens, G.; Rappold, A.; Seith, W.

    1977-01-01

    The influence of a TV broadcasting satellite, transmitting four additional TV networks was analyzed. It is assumed that the cost of the satellite systems will be financed by the cable TV system operators. The additional TV programs increase income by attracting additional subscribers. Two economic models were established: (1) each local network is regarded as an independent economic unit with individual fees (cost price model) and (2) all networks are part of one public cable TV company with uniform fees (uniform price model). Assumptions are made for penetration as a function of subscription rates. Main results of the study are: the installation of a TV broadcasting satellite improves the economics of CTV-networks in both models; the overall coverage achievable by the uniform price model is significantly higher than that achievable by the cost price model.

  15. Dextransucrase production using cashew apple juice as substrate: effect of phosphate and yeast extract addition.

    PubMed

    Chagas, Clarice M A; Honorato, Talita L; Pinto, Gustavo A S; Maia, Geraldo A; Rodrigues, Sueli

    2007-05-01

    Cashew apples are considered agriculture excess in the Brazilian Northeast because cashew trees are cultivated primarily with the aim of cashew nut production. In this work, the use of cashew apple juice as a substrate for Leuconostoc mesenteroides cultivation was investigated. The effect of yeast extract and phosphate addition was evaluated using factorial planning tools. Both phosphate and yeast extract addition were significant factors for biomass growth, but had no significant effect on maximum enzyme activity. The enzyme activities found in cashew apple juice assays were at least 3.5 times higher than the activity found in the synthetic medium. Assays with pH control (pH = 6.5) were also carried out. The pH-controlled fermentation enhanced biomass growth, but decreased the enzyme activity. Crude enzyme free of cells produced using cashew apple juice was stable for 16 h at 30 degrees C at a pH of 5.0.

  16. The Significance of Hydrogen Sulfide for Arabidopsis Seed Germination

    PubMed Central

    Baudouin, Emmanuel; Poilevey, Aurélie; Hewage, Nishodi Indiketi; Cochet, Françoise; Puyaubert, Juliette; Bailly, Christophe

    2016-01-01

    Hydrogen sulfide (H2S) recently emerged as an important gaseous signaling molecule in plants. In this study, we investigated the possible functions of H2S in regulating Arabidopsis seed germination. NaHS treatments delayed seed germination in a dose-dependent manner and were ineffective in releasing seed dormancy. Interestingly, endogenous H2S content was enhanced in germinating seeds. This increase was correlated with higher activity of three enzymes (L-cysteine desulfhydrase, D-cysteine desulfhydrase, and β-cyanoalanine synthase) known as sources of H2S in plants. The H2S scavenger hypotaurine and the D/L cysteine desulfhydrase inhibitor propargylglycine significantly delayed seed germination. We analyzed the germinative capacity of des1 seeds mutated in Arabidopsis cytosolic L-cysteine desulfhydrase. Although the mutant seeds do not exhibit germination-evoked H2S formation, they retained similar germination capacity as the wild-type seeds. In addition, des1 seeds responded similarly to temperature and were as sensitive to ABA as wild type seeds. Taken together, these data suggest that, although its metabolism is stimulated upon seed imbibition, H2S plays, if any, a marginal role in regulating Arabidopsis seed germination under standard conditions. PMID:27446159

  17. The Significance of Hydrogen Sulfide for Arabidopsis Seed Germination.

    PubMed

    Baudouin, Emmanuel; Poilevey, Aurélie; Hewage, Nishodi Indiketi; Cochet, Françoise; Puyaubert, Juliette; Bailly, Christophe

    2016-01-01

    Hydrogen sulfide (H2S) recently emerged as an important gaseous signaling molecule in plants. In this study, we investigated the possible functions of H2S in regulating Arabidopsis seed germination. NaHS treatments delayed seed germination in a dose-dependent manner and were ineffective in releasing seed dormancy. Interestingly, endogenous H2S content was enhanced in germinating seeds. This increase was correlated with higher activity of three enzymes (L-cysteine desulfhydrase, D-cysteine desulfhydrase, and β-cyanoalanine synthase) known as sources of H2S in plants. The H2S scavenger hypotaurine and the D/L cysteine desulfhydrase inhibitor propargylglycine significantly delayed seed germination. We analyzed the germinative capacity of des1 seeds mutated in Arabidopsis cytosolic L-cysteine desulfhydrase. Although the mutant seeds do not exhibit germination-evoked H2S formation, they retained similar germination capacity as the wild-type seeds. In addition, des1 seeds responded similarly to temperature and were as sensitive to ABA as wild type seeds. Taken together, these data suggest that, although its metabolism is stimulated upon seed imbibition, H2S plays, if any, a marginal role in regulating Arabidopsis seed germination under standard conditions.

  18. Black holes in higher derivative gravity.

    PubMed

    Lü, H; Perkins, A; Pope, C N; Stelle, K S

    2015-05-01

    Extensions of Einstein gravity with higher-order derivative terms arise in string theory and other effective theories, as well as being of interest in their own right. In this Letter we study static black-hole solutions in the example of Einstein gravity with additional quadratic curvature terms. A Lichnerowicz-type theorem simplifies the analysis by establishing that they must have vanishing Ricci scalar curvature. By numerical methods we then demonstrate the existence of further black-hole solutions over and above the Schwarzschild solution. We discuss some of their thermodynamic properties, and show that they obey the first law of thermodynamics.

  19. Black holes in higher derivative gravity.

    PubMed

    Lü, H; Perkins, A; Pope, C N; Stelle, K S

    2015-05-01

    Extensions of Einstein gravity with higher-order derivative terms arise in string theory and other effective theories, as well as being of interest in their own right. In this Letter we study static black-hole solutions in the example of Einstein gravity with additional quadratic curvature terms. A Lichnerowicz-type theorem simplifies the analysis by establishing that they must have vanishing Ricci scalar curvature. By numerical methods we then demonstrate the existence of further black-hole solutions over and above the Schwarzschild solution. We discuss some of their thermodynamic properties, and show that they obey the first law of thermodynamics. PMID:25978224

  20. Supplier Selection Using Weighted Utility Additive Method

    NASA Astrophysics Data System (ADS)

    Karande, Prasad; Chakraborty, Shankar

    2015-10-01

    Supplier selection is a multi-criteria decision-making (MCDM) problem which mainly involves evaluating a number of available suppliers according to a set of common criteria for choosing the best one to meet the organizational needs. For any manufacturing or service organization, selecting the right upstream suppliers is a key success factor that will significantly reduce purchasing cost, increase downstream customer satisfaction and improve competitive ability. The past researchers have attempted to solve the supplier selection problem employing different MCDM techniques which involve active participation of the decision makers in the decision-making process. This paper deals with the application of weighted utility additive (WUTA) method for solving supplier selection problems. The WUTA method, an extension of utility additive approach, is based on ordinal regression and consists of building a piece-wise linear additive decision model from a preference structure using linear programming (LP). It adopts preference disaggregation principle and addresses the decision-making activities through operational models which need implicit preferences in the form of a preorder of reference alternatives or a subset of these alternatives present in the process. The preferential preorder provided by the decision maker is used as a restriction of a LP problem, which has its own objective function, minimization of the sum of the errors associated with the ranking of each alternative. Based on a given reference ranking of alternatives, one or more additive utility functions are derived. Using these utility functions, the weighted utilities for individual criterion values are combined into an overall weighted utility for a given alternative. It is observed that WUTA method, having a sound mathematical background, can provide accurate ranking to the candidate suppliers and choose the best one to fulfill the organizational requirements. Two real time examples are illustrated to prove