Science.gov

Sample records for additional field testing

  1. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

    SciTech Connect

    Gary M. Blythe

    2006-03-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, ''Field Testing of a Wet FGD Additive.'' The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemissions of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate that the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project will conduct pilot and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosage requirements to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB co-fired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot and full-scale jet bubbling reactor (JBR) FGD systems to be tested. A third utility, to be named later, will provide the high-sulfur Eastern bituminous coal full-scale FGD test site. Degussa Corporation is providing the TMT-15 additive and technical support to the test program. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in

  2. Acceptance test report: Field test of mixer pump for 241-AN-107 caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1997-05-16

    The field acceptance test of a 75 HP mixer pump (Hazleton serial number N-20801) installed in Tank 241-AN-107 was conducted from October 1995 thru February 1996. The objectives defined in the acceptance test were successfully met, with two exceptions recorded. The acceptance test encompassed field verification of mixer pump turntable rotation set-up and operation, verification that the pump instrumentation functions within established limits, facilitation of baseline data collection from the mixer pump mounted ultrasonic instrumentation, verification of mixer pump water flush system operation and validation of a procedure for its operation, and several brief test runs (bump) of the mixer pump.

  3. Field Testing of a Wet FGD Additive for Enhanced Mercury Control

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-31

    This document is the final report for DOE-NETL Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project has been to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project was intended to demonstrate whether such additives can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project involved pilot- and full-scale tests of the additives in wet FGD absorbers. The tests were intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power provided the Texas lignite/PRB co-fired test site for pilot FGD tests and project cost sharing. Southern Company provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested, and project cost sharing. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation provided the TMT-15 additive, and the Nalco Company provided the Nalco 8034 additive. Both companies also supplied technical support to the test program as in-kind cost sharing. The project was conducted in six tasks. Of the six tasks, Task 1 involved project planning and Task 6 involved

  4. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    SciTech Connect

    Gary Blythe

    2007-05-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing

  5. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the additives in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power has provided the Texas lignite/PRB co-fired test site for pilot FGD tests and cost sharing. Southern Company has provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation is providing the TMT-15 additive, and the Nalco Company is providing the Nalco 8034 additive. Both companies are also supplying technical support to the test program as in-kind cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management

  6. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  7. An Additive Manufacturing Test Artifact

    PubMed Central

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  8. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system.

  9. LSA field test

    NASA Technical Reports Server (NTRS)

    Jaffe, P.

    1979-01-01

    Degradation tests indicate that electrical degradation is not a slow monotonically increasing phenomenon as originally thought but occurs abruptly as the result of some traumatic event. This finding has led to a change in the test philosophy. A discussion of this change is presented along with a summary of degradation and failure data from all the sites and results from a variety of special tests. New instrumentation for in-field measurements are described. Field testing activity was expanded by the addition of twelve remote sites located as far away as Alaska and the Canal Zone. Descriptions of the new sites are included.

  10. [Patch-testing methods: additional specialised or additional series].

    PubMed

    Cleenewerck, M-B

    2009-01-01

    The tests in the European standard battery must occasionally be supplemented by specialised or additional batteries, particularly where the contact allergy is thought to be of occupational origin. These additional batteries cover all allergens associated with various professional activities (hairdressing, baking, dentistry, printing, etc.) and with different classes of materials and chemical products (glue, plastic, rubber...). These additional tests may also include personal items used by patients on a daily basis such as cosmetics, shoes, plants, textiles and so on.

  11. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  12. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  13. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  14. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  15. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  16. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  17. 78 FR 22209 - Additional Synthetic Drug Testing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-15

    ... COMMISSION 10 CFR Part 26 Additional Synthetic Drug Testing AGENCY: Nuclear Regulatory Commission. ACTION... NRC amend its Fitness for Duty program regulations to amend drug testing requirements to test for additional synthetic drugs currently not included in the regulations. The NRC determined that the...

  18. Caustic addition system operability test procedure

    SciTech Connect

    Parazin, R.E.

    1994-11-01

    This test procedure provides instructions for performing operational testing of the major components of the 241-AN-107 Caustic Addition System by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

  19. Additive empirical force field for hexopyranose monosaccharides

    PubMed Central

    Guvench, Olgun; Greene, Shannon N.; Kamath, Ganesh; Brady, John W.; Venable, Richard M.; Pastor, Richard W.; MacKerell, Alexander D.

    2010-01-01

    We present an all-atom additive empirical force field for the hexopyranose monosaccharide form of glucose and its diastereomers allose, altrose, galactose, gulose, idose, mannose, and talose. The model is developed to be consistent with the CHARMM all-atom biomolecular force fields, and the same parameters are used for all diastereomers, including both the α- and β-anomers of each monosaccharide. The force field is developed in a hierarchical manner and reproduces the gas-phase and condensed-phase properties of small-molecule model compounds corresponding to fragments of pyranose monosaccharides. The resultant parameters are transferred to the full pyranose monosaccharides and additional parameter development is done to achieve a complete hexopyranose monosaccharide force field. Parametrization target data include vibrational frequencies, crystal geometries, solute – water interaction energies, molecular volumes, heats of vaporization, and conformational energies, including those for over 1800 monosaccharide conformations at the MP2/cc-pVTZ//MP2/6-31G(d) level of theory. Though not targeted during parametrization, free energies of aqueous solvation for the model compounds compare favorably with experimental values. Also well-reproduced are monosaccharide crystal unit cell dimensions and ring pucker, densities of concentrated aqueous glucose systems, and the thermodynamic and dynamic properties of the exocyclic torsion in dilute aqueous systems. The new parameter set expands the CHARMM additive force field to allow for simulation of heterogeneous systems that include hexopyranose monosaccharides in addition to proteins, nucleic acids, and lipids. PMID:18470966

  20. Field test experience

    NASA Technical Reports Server (NTRS)

    Weaver, R. W.

    1983-01-01

    As a part of the Flat-Plate Solar Array Project (FSA), a field-test program was developed to obtain solar photovoltaic (PV) module performance and endurance data. These data are used to identify the specific characteristics of module designs under various environmental conditions. The information obtained from field testing is useful to all participants in the National Photovoltaics Program, from the research planner to the life-cycle cost analyst.

  1. FSA field test

    NASA Technical Reports Server (NTRS)

    Jaffe, P.; Weaver, R. W.; Lee, R. E.

    1981-01-01

    The 12 continental remote sites were decommissioned. Testing was consolidated into a five-site network consisting of the four Southern California sites and a new Florida site. 16 kW of new state-of-the-art modules were deployed at the five sites. Testing of the old modules continued at the Goldstone site but as a low-priority item. Array testing of modules is considered. Additional new testing capabilities were added. A battery-powered array data logger is discussed. A final set of failure and degradation data was obtained from the modules.

  2. Laboratory tests of sludge-control additives

    SciTech Connect

    Tatnall, R.E.

    1996-07-01

    Laboratory {open_quotes}jar{close_quotes} tests compared eleven different fuel oil and diesel fuel sludge-control additives. Factors studied included (1) ability to disperse and prevent buildup of sludge deposits on surfaces, (2) ability to protect steel from corrosion, (3) ability to inhibit growth and proliferation of bacteria, and (4) ability to disperse water. Results varied greatly, and it was found that many commercial products do not do what they claim. It is concluded that fuel retailers should not believe manufacturers` claims for their additive products, but rather should test such products themselves to be sure that the benefits of treatment are real. A simplified form of the procedure used here is proposed as one way for dealers to do such testing.

  3. The teratology testing of food additives.

    PubMed

    Barrow, Paul C; Spézia, François

    2013-01-01

    The developmental and reproductive toxicity testing (including teratogenicity) of new foods and food additives is performed worldwide according to the guidelines given in the FDA Redbook. These studies are not required for substances that are generally recognized as safe, according to the FDA inventory. The anticipated cumulated human exposure level above which developmental or reproduction studies are required depends on the structure-alert category. For food additives of concern, both developmental (prenatal) and reproduction (multigeneration) studies are required. The developmental studies are performed in two species, usually the rat and the rabbit. The reproduction study is generally performed in the rat. The two rat studies are preferably combined into a single experimental design, if possible. The test methods described in the FDA Redbook are similar to those specified by the OECD for the reproductive toxicity testing of chemicals.

  4. RESOLVE 2010 Field Test

    NASA Technical Reports Server (NTRS)

    Captain, J.; Quinn, J.; Moss, T.; Weis, K.

    2010-01-01

    This slide presentation reviews the field tests conducted in 2010 of the Regolith Environment Science & Oxygen & Lunar Volatile Extraction (RESOLVE). The Resolve program consist of several mechanism: (1) Excavation and Bulk Regolith Characterization (EBRC) which is designed to act as a drill and crusher, (2) Regolith Volatiles Characterization (RVC) which is a reactor and does gas analysis,(3) Lunar Water Resources Demonstration (LWRD) which is a fluid system, water and hydrogen capture device and (4) the Rover. The scientific goal of this test is to demonstrate evolution of low levels of hydrogen and water as a function of temperature. The Engineering goals of this test are to demonstrate:(1) Integration onto new rover (2) Miniaturization of electronics rack (3) Operation from battery packs (elimination of generator) (4) Remote command/control and (5) Operation while roving. Views of the 2008 and the 2010 mechanisms, a overhead view of the mission path, a view of the terrain, the two drill sites, and a graphic of the Master Events Controller Graphical User Interface (MEC GUI) are shown. There are descriptions of the Gas chromatography (GC), the operational procedure, water and hydrogen doping of tephra. There is also a review of some of the results, and future direction for research and tests.

  5. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free...

  6. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free...

  7. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free...

  8. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... controlled by the pilot under normal operating conditions (such as where the primary engine power control is...: (1) Category A. Unless such failures are extremely remote, it must be shown by test that any...

  9. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... controlled by the pilot under normal operating conditions (such as where the primary engine power control is...: (1) Category A. Unless such failures are extremely remote, it must be shown by test that any...

  10. LSA field test

    NASA Technical Reports Server (NTRS)

    Jaffe, P.

    1980-01-01

    After almost four years of endurance testing of photovoltaic modules, no fundamental life-limiting mechanisms were identified that could prevent the twenty-year life goal from being met. The endure data show a continual decline in the failure rate with each new large-scale procurement. Cracked cells and broken interconnects continue to be the principal causes of failure. Although the modules are more adversely affected physically by hot, humid environments than by cool or dry environments there are insufficient data to correlate failure with environment. There is little connection between the outward physical condition of a module and changes in its electrical performance.

  11. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  12. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  13. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  14. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  15. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  16. Production Hydraulic Packer Field Test

    SciTech Connect

    Schneller, Tricia; Salas, Jose

    2000-06-30

    In October 1999, the Rocky Mountain Oilfield Testing Center and Halliburton Energy Services cooperated on a field test of Halliburton's new Production Hydraulic Packer technology on Well 46-TPX-10 at Naval Petroleum Reserve No. 3 near Casper, WY. Performance of the packer was evaluated in set and unset operations. The packer's ability to seal the annulus between the casing and tubing was hydraulically tested and the results were recorded.

  17. The North Carolina Field Test

    SciTech Connect

    Sharp, T.R.; Ternes, M.P.

    1990-08-01

    The North Carolina Field Test will test the effectiveness of two weatherization approaches: the current North Carolina Low-Income Weatherization Assistance Program and the North Carolina Field Test Audit. The Field Test Audit will differ from North Carolina's current weatherization program in that it will incorporate new weatherization measures and techniques, a procedure for basing measure selection of the characteristics of the individual house and the cost-effectiveness of the measure, and also emphasize cooling energy savings. The field test will determine the differences of the two weatherization approaches from the viewpoints of energy savings, cost effectiveness, and implementation ease. This Experimental Plan details the steps in performing the field test. The field test will be a group effort by several participating organizations. Pre- and post-weatherization data will be collected over a two-year period (November 1989 through August 1991). The 120 houses included in the test will be divided into a control group and two treatment groups (one for each weatherization procedure) of 40 houses each. Weekly energy use data will be collected for each house representing whole-house electric, space heating and cooling, and water heating energy uses. Corresponding outdoor weather and house indoor temperature data will also be collected. The energy savings of each house will be determined using linear-regression based models. To account for variations between the pre- and post-weatherization periods, house energy savings will be normalized for differences in outdoor weather conditions and indoor temperatures. Differences between the average energy savings of treatment groups will be identified using an analysis of variance approach. Differences between energy savings will be quantified using multiple comparison techniques. 9 refs., 8 figs., 5 tabs.

  18. Report of Field Test Evaluation.

    ERIC Educational Resources Information Center

    Michigan State Univ., East Lansing. Regional Instructional Materials Center for Handicapped Children and Youth.

    Reported by the Great Lakes Region Special Education Instructional Materials Center are field test evaluation of 18 auditory instructional materials for use with handicapped children who learn best through the auditory modality. Among materials evaluated are a taped program on use of the abacus and a cassette audiotape on bird habits and sounds.…

  19. STIS Sparse Field CTE test

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    1997-07-01

    CTE measurements are made using the "sparse field test", along both the serial and parallel axes. This program needs special commanding to provide {a} off-center MSM positionings of some slits, and {b} the ability to read out with any amplifier {A, B, C, or D}. All exposures are internals.

  20. Descent Advisor Preliminary Field Test

    NASA Technical Reports Server (NTRS)

    Green, Steven M.; Vivona, Robert A.; Sanford, Beverly

    1995-01-01

    A field test of the Descent Advisor (DA) automation tool was conducted at the Denver Air Route Traffic Control Center in September 1994. DA is being developed to assist Center controllers in the efficient management and control of arrival traffic. DA generates advisories, based on trajectory predictions, to achieve accurate meter-fix arrival times in a fuel efficient manner while assisting the controller with the prediction and resolution of potential conflicts. The test objectives were: (1) to evaluate the accuracy of DA trajectory predictions for conventional and flight-management system equipped jet transports, (2) to identify significant sources of trajectory prediction error, and (3) to investigate procedural and training issues (both air and ground) associated with DA operations. Various commercial aircraft (97 flights total) and a Boeing 737-100 research aircraft participated in the test. Preliminary results from the primary test set of 24 commercial flights indicate a mean DA arrival time prediction error of 2.4 seconds late with a standard deviation of 13.1 seconds. This paper describes the field test and presents preliminary results for the commercial flights.

  1. Descent advisor preliminary field test

    NASA Technical Reports Server (NTRS)

    Green, Steven M.; Vivona, Robert A.; Sanford, Beverly

    1995-01-01

    A field test of the Descent Advisor (DA) automation tool was conducted at the Denver Air Route Traffic Control Center in September 1994. DA is being developed to assist Center controllers in the efficient management and control of arrival traffic. DA generates advisories, based on trajectory predictions, to achieve accurate meter-fix arrival times in a fuel efficient manner while assisting the controller with the prediction and resolution of potential conflicts. The test objectives were to evaluate the accuracy of DA trajectory predictions for conventional- and flight-management-system-equipped jet transports, to identify significant sources of trajectory prediction error, and to investigate procedural and training issues (both air and ground) associated with DA operations. Various commercial aircraft (97 flights total) and a Boeing 737-100 research aircraft participated in the test. Preliminary results from the primary test set of 24 commercial flights indicate a mean DA arrival time prediction error of 2.4 sec late with a standard deviation of 13.1 sec. This paper describes the field test and presents preliminary results for the commercial flights.

  2. Cryopumping field joint can testing

    NASA Astrophysics Data System (ADS)

    Johnson, Wesley; Fesmire, James; Meneghelli, Barry

    2012-06-01

    For long installations, vacuum jacketed piping often comes in 40 foot sections that are butt welded together in the field. A short can is then welded over the bare pipe connection to allow for insulation to be protected from the environment. Traditionally, the field joint is insulated with multilayer insulation and a vacuum is pulled on the can to minimize heat leak through the bare section and prevent frost from forming on the pipe section. The vacuum jacketed lines for the Ares I mobile launch platform were to be a combined 2000 feet long, with 60+ pipe sections and field joint cans. Historically, Kennedy Space Center has drilled a hole in the long sections to create a common vacuum with the field joint can to minimize maintenance on the vacuum jacketed piping. However, this effort looked at ways to use a passive system that didn't require a vacuum, but may cryopump to create its own vacuum. Various forms of aerogel, multilayer insulations, and combinations thereof were tested to determine the best method of insulating the field joint while minimizing maintenance and thermal losses.

  3. Cryopumping Field Joint Can Testing

    NASA Technical Reports Server (NTRS)

    Johnson, Wesley L.; Fesmire, James E.; Meneghelli, Barry E.

    2011-01-01

    For long installations, vacuum jacketed piping often comes in 40 foot sections that are butt welded together in the field. A short can is then welded over the bare pipe connection to allow for insulation to be protected from the environment. Traditionally, the field joint is insulated with multilayer insulation and a vacuum is pulled on the can to minimize heat leak through the bare section and prevent frost from forming on the pipe section. The vacuum jacketed lines for the Ares I mobile launch platform were to be a combined 2000 feet long, with 60+ pipe sections and field joint cans. Historically, Kennedy Space Center has drilled a hole in the long sections to create a common vacuum with the field joint can to minimize maintenance on the vacuum jacketed piping. However, this effort looked at ways to use a passive system that didn't require a vacuum, but may cryopump to create its own vacuum. Various forms of aerogel, multilayer insulations, and combinations thereof were tested to determine the best method of insulating the field joint while minimizing maintenance and thermal losses.

  4. Test Procedure - pumping system for caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1994-10-01

    This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

  5. 30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING WEST. ORIGINALLY HAD SUSPENDED ACOUSTICAL CEILINGS WITH FLOURESCENT LIGHTING AND ASPHALT MASTIC TILE FLOORS - Underwriters' Laboratories, 207-231 East Ohio Street, Chicago, Cook County, IL

  6. Additive CHARMM force field for naturally occurring modified ribonucleotides

    PubMed Central

    Xu, You; Vanommeslaeghe, Kenno; Aleksandrov, Alexey; MacKerell, Alexander D.

    2016-01-01

    More than 100 naturally occurring modified nucleotides have been found in RNA molecules, in particular in tRNAs. We have determined molecular mechanics force field parameters compatible with the CHARMM36 all‐atom additive force field for all these modifications using the CHARMM force field parametrization strategy. Emphasis was placed on fine tuning of the partial atomic charges and torsion angle parameters. Quantum mechanics calculations on model compounds provided the initial set of target data, and extensive molecular dynamics simulations of nucleotides and oligonucleotides in aqueous solutions were used for further refinement against experimental data. The presented parameters will allow for computational studies of a wide range of RNAs containing modified nucleotides, including the ribosome and transfer RNAs. © 2016 The Authors. Journal of Computational Chemistry Published by Wiley Periodicals, Inc. PMID:26841080

  7. Additive CHARMM force field for naturally occurring modified ribonucleotides.

    PubMed

    Xu, You; Vanommeslaeghe, Kenno; Aleksandrov, Alexey; MacKerell, Alexander D; Nilsson, Lennart

    2016-04-15

    More than 100 naturally occurring modified nucleotides have been found in RNA molecules, in particular in tRNAs. We have determined molecular mechanics force field parameters compatible with the CHARMM36 all-atom additive force field for all these modifications using the CHARMM force field parametrization strategy. Emphasis was placed on fine tuning of the partial atomic charges and torsion angle parameters. Quantum mechanics calculations on model compounds provided the initial set of target data, and extensive molecular dynamics simulations of nucleotides and oligonucleotides in aqueous solutions were used for further refinement against experimental data. The presented parameters will allow for computational studies of a wide range of RNAs containing modified nucleotides, including the ribosome and transfer RNAs. PMID:26841080

  8. Additive CHARMM force field for naturally occurring modified ribonucleotides.

    PubMed

    Xu, You; Vanommeslaeghe, Kenno; Aleksandrov, Alexey; MacKerell, Alexander D; Nilsson, Lennart

    2016-04-15

    More than 100 naturally occurring modified nucleotides have been found in RNA molecules, in particular in tRNAs. We have determined molecular mechanics force field parameters compatible with the CHARMM36 all-atom additive force field for all these modifications using the CHARMM force field parametrization strategy. Emphasis was placed on fine tuning of the partial atomic charges and torsion angle parameters. Quantum mechanics calculations on model compounds provided the initial set of target data, and extensive molecular dynamics simulations of nucleotides and oligonucleotides in aqueous solutions were used for further refinement against experimental data. The presented parameters will allow for computational studies of a wide range of RNAs containing modified nucleotides, including the ribosome and transfer RNAs.

  9. Additional electric field in real trench MOS barrier Schottky diode

    NASA Astrophysics Data System (ADS)

    Mamedov, R. K.; Aslanova, A. R.

    2016-04-01

    In real trench MOS barrier Schottky diode (TMBS diode) additional electric field (AEF) the whole is formed in the near contact region of the semiconductor and its propagation space is limited with the barrier metal and the metallic electrodes of MOS structures. Effective potential barrier height TMBS diode is formed via resulting electric field of superposition AEF and electric field of space charge region (SCR) semiconductor. The dependence of the resulting electric field intensity of the distance towards the inside the semiconductor is nonlinear and characterized by a peak at a certain distance from the interface. The thickness of the SCR in TMBS diode becomes equal to the trench depth. Force and energy parameters of the AEF, and thus resulting electric field in the SCR region, become dependent on the geometric design parameters TMBS diode. The forward I-V characteristic TMBS diode is described by the thermionic emission theory as in conventional flat Scottky diode, and in the reverse bias, current is virtually absent at initial voltage, appears abruptly at a certain critical voltage.

  10. Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

    PubMed

    Law, S L; Newman, J H; Ptak, F L

    1990-02-01

    A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

  11. Simple Additivity of Stochastic Psychological Processes: Tests and Measures.

    ERIC Educational Resources Information Center

    Balakrishnan, J. D.

    1994-01-01

    Methods of testing relatively complete (distributional) models of internal psychological processes are described. It is shown that there is a sufficient condition for additive models to imply this property of the likelihood ratio. Also discussed are the examination of hazard rate functions of component processes and change in cumulative…

  12. Basophil activation test with food additives in chronic urticaria patients.

    PubMed

    Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up; Chang, Yoon-Seok

    2014-01-01

    The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU.

  13. Basophil Activation Test with Food Additives in Chronic Urticaria Patients

    PubMed Central

    Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up

    2014-01-01

    The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU. PMID:24527415

  14. IN SITU FIELD TESTING OF PROCESSES

    SciTech Connect

    J.S.Y. YANG

    2004-11-08

    The purpose of this scientific analysis report is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts and surface-based boreholes through unsaturated zone (UZ) tuff rock units. In situ testing, monitoring, and associated laboratory studies are conducted to directly assess and evaluate the waste emplacement environment and the natural barriers to radionuclide transport at Yucca Mountain. This scientific analysis report supports and provides data to UZ flow and transport model reports, which in turn contribute to the Total System Performance Assessment (TSPA) of Yucca Mountain, an important document for the license application (LA). The objectives of ambient field-testing activities are described in Section 1.1. This report is the third revision (REV 03), which supercedes REV 02. The scientific analysis of data for inputs to model calibration and validation as documented in REV 02 were developed in accordance with the Technical Work Plan (TWP) ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (BSC 2004 [DIRS 167969]). This revision was developed in accordance with the ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654], Section 1.2.4) for better integrated, consistent, transparent, traceable, and more complete documentation in this scientific analysis report and associated UZ flow and transport model reports. No additional testing or analyses were performed as part of this revision. The list of relevant acceptance criteria is provided by ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654]), Table 3-1. Additional deviations from the TWP regarding the features, events, and processes (FEPs) list are discussed in Section 1.3. Documentation in this report includes descriptions of how, and under what conditions, the tests were conducted. The descriptions and

  15. Introduction to Analog Field Testing

    NASA Video Gallery

    NASA tests systems and operational concepts in analog environments, which include locations underwater, in the arctic, on terrestrial impact craters, in the desert, and on the International Space S...

  16. A model for field toxicity tests

    USGS Publications Warehouse

    Kaiser, Mark S.; Finger, Susan E.

    1996-01-01

    Toxicity tests conducted under field conditions present an interesting challenge for statistical modelling. In contrast to laboratory tests, the concentrations of potential toxicants are not held constant over the test. In addition, the number and identity of toxicants that belong in a model as explanatory factors are not known and must be determined through a model selection process. We present one model to deal with these needs. This model takes the record of mortalities to form a multinomial distribution in which parameters are modelled as products of conditional daily survival probabilities. These conditional probabilities are in turn modelled as logistic functions of the explanatory factors. The model incorporates lagged values of the explanatory factors to deal with changes in the pattern of mortalities over time. The issue of model selection and assessment is approached through the use of generalized information criteria and power divergence goodness-of-fit tests. These model selection criteria are applied in a cross-validation scheme designed to assess the ability of a model to both fit data used in estimation and predict data deleted from the estimation data set. The example presented demonstrates the need for inclusion of lagged values of the explanatory factors and suggests that penalized likelihood criteria may not provide adequate protection against overparameterized models in model selection.

  17. Analyzing Educational Testing Service Graduate Major Field Test Results

    ERIC Educational Resources Information Center

    Thornton, Barry; Arbogast, Gordon

    2012-01-01

    The Educational Testing Service (ETS) created the Graduate Major Field Test in Business (GMFT-B) for MBA students. This test is administered to all MBA classes at Jacksonville University for the purpose of measuring student academic achievement and growth, as well as to assess educational outcomes. The test is given in the capstone course,…

  18. Development of additional tasks for the executive function performance test.

    PubMed

    Hahn, Bridget; Baum, Carolyn; Moore, Jennifer; Ehrlich-Jones, Linda; Spoeri, Susan; Doherty, Meghan; Wolf, Timothy J

    2014-01-01

    OBJECTIVE. The Executive Function Performance Test (EFPT) is a reliable and valid performance-based assessment of executive function for people with stroke. The objective of this study was to enhance the clinical utility of the EFPT by developing and testing additional tasks for the EFPT in the Alternate EFPT (aEFPT). METHOD. We performed a cross-sectional study with poststroke participants (n = 25) and healthy control participants (n = 25). All participants completed a neuropsychological assessment battery and both the EFPT and the aEFPT. RESULTS. No statistically significant differences were found between the EFPT and the aEFPT when examining total scores, construct scores, and two overall task scores. Correlations between the aEFPT and the neuropsychological measures were adequate to strong (r2s = .59-.83). CONCLUSION. The aEFPT tasks are comparable to the original EFPT tasks, providing occupational therapy practitioners with additional tasks that can be used clinically to identify performance-based executive function deficits in people with stroke. PMID:25397771

  19. Minicourse 18: Main Field Test Report.

    ERIC Educational Resources Information Center

    Skailand, Dawn

    This report describes the main field test of Minicourse 18: Teaching Reading as Decoding. The purposes of the main field test were: (1) to evaluate the effects of the course on the participating teachers, (2) to evaluate four reteach treatments on teacher skill acquisition, (3) to compare scores for central city and suburban teachers, and (4) to…

  20. Field Testing: A Model and Its Applications.

    ERIC Educational Resources Information Center

    Goldstein, Marjorie T.

    Described is a Social Learning Curriculum (SLC) field test model that focuses on aspects of personnel utilization, communication systems, and the quality of human communication and that highlights the role of the supervisor in the education of the mentally retarded. The four field test model phases discussed are 1) the planning phase (including…

  1. Test fields cannot destroy extremal black holes

    NASA Astrophysics Data System (ADS)

    Natário, José; Queimada, Leonel; Vicente, Rodrigo

    2016-09-01

    We prove that (possibly charged) test fields satisfying the null energy condition at the event horizon cannot overspin/overcharge extremal Kerr–Newman or Kerr–Newman–anti de Sitter black holes, that is, the weak cosmic censorship conjecture cannot be violated in the test field approximation. The argument relies on black hole thermodynamics (without assuming cosmic censorship), and does not depend on the precise nature of the fields. We also discuss generalizations of this result to other extremal black holes.

  2. Test fields cannot destroy extremal black holes

    NASA Astrophysics Data System (ADS)

    Natário, José; Queimada, Leonel; Vicente, Rodrigo

    2016-09-01

    We prove that (possibly charged) test fields satisfying the null energy condition at the event horizon cannot overspin/overcharge extremal Kerr-Newman or Kerr-Newman-anti de Sitter black holes, that is, the weak cosmic censorship conjecture cannot be violated in the test field approximation. The argument relies on black hole thermodynamics (without assuming cosmic censorship), and does not depend on the precise nature of the fields. We also discuss generalizations of this result to other extremal black holes.

  3. Additives

    NASA Technical Reports Server (NTRS)

    Smalheer, C. V.

    1973-01-01

    The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

  4. Testing 1...2...3...: Additional Files Available for Test Information Online.

    ERIC Educational Resources Information Center

    Fabiano, Emily

    1984-01-01

    Reviews databases providing information on published, standardized and unpublished, non-standardized test instruments: Educational Testing Service File, Mental Measurements Yearbook Database, Dissertation Abstracts Online, ERIC, and Psychological Abstracts. Search strategies, search examples, and a summary chart of searchable fields for test…

  5. Livestock poisoning from oil field drilling fluids, muds and additives.

    PubMed

    Edwards, W C; Gregory, D G

    1991-10-01

    The use and potential toxicity of various components of oil well drilling fluids, muds and additives are presented. Many components are extremely caustic resulting in rumenitis. Solvent and petroleum hydrocarbon components may cause aspiration pneumonia and rumen dysfunction. Some additives cause methemoglobinemia. The most frequently encountered heavy metals are lead, chromium, arsenic, lithium and copper. Considerations for investigating livestock poisoning cases and several typical cases are reviewed.

  6. Livestock poisoning from oil field drilling fluids, muds and additives

    SciTech Connect

    Edwards, W.C.; Gregory, D.G. )

    1991-10-01

    The use and potential toxicity of various components of oil well drilling fluids, muds and additives are presented. Many components are extremely caustic resulting in rumenitis. Solvent and petroleum hydrocarbon components may cause aspiration pneumonia and rumen dysfunction. Some additives cause methemoglobinemia. The most frequently encountered heavy metals are lead, chromium, arsenic, lithium and copper. Considerations for investigating livestock poisoning cases and several typical cases are reviewed.

  7. Testing for Additivity at Select Mixture Groups of Interest Based on Statistical Equivalence Testing Methods

    SciTech Connect

    Stork, LeAnna M.; Gennings, Chris; Carchman, Richard; Carter, Jr., Walter H.; Pounds, Joel G.; Mumtaz, Moiz

    2006-12-01

    Several assumptions, defined and undefined, are used in the toxicity assessment of chemical mixtures. In scientific practice mixture components in the low-dose region, particularly subthreshold doses, are often assumed to behave additively (i.e., zero interaction) based on heuristic arguments. This assumption has important implications in the practice of risk assessment, but has not been experimentally tested. We have developed methodology to test for additivity in the sense of Berenbaum (Advances in Cancer Research, 1981), based on the statistical equivalence testing literature where the null hypothesis of interaction is rejected for the alternative hypothesis of additivity when data support the claim. The implication of this approach is that conclusions of additivity are made with a false positive rate controlled by the experimenter. The claim of additivity is based on prespecified additivity margins, which are chosen using expert biological judgment such that small deviations from additivity, which are not considered to be biologically important, are not statistically significant. This approach is in contrast to the usual hypothesis-testing framework that assumes additivity in the null hypothesis and rejects when there is significant evidence of interaction. In this scenario, failure to reject may be due to lack of statistical power making the claim of additivity problematic. The proposed method is illustrated in a mixture of five organophosphorus pesticides that were experimentally evaluated alone and at relevant mixing ratios. Motor activity was assessed in adult male rats following acute exposure. Four low-dose mixture groups were evaluated. Evidence of additivity is found in three of the four low-dose mixture groups.The proposed method tests for additivity of the whole mixture and does not take into account subset interactions (e.g., synergistic, antagonistic) that may have occurred and cancelled each other out.

  8. Testing Large Structures in the Field

    NASA Technical Reports Server (NTRS)

    James, George; Carne, Thomas G.

    2009-01-01

    Field testing large structures creates unique challenges such as limited choices for boundary conditions and the fact that natural excitation sources cannot be removed. Several critical developments in field testing of large structures are reviewed, including: step relaxation testing which has been developed into a useful technique to apply large forces to operational systems by careful windowing; the capability of large structures testing with free support conditions which has been expanded by implementing modeling of the support structure; natural excitation which has been developed as a viable approach to field testing; and the hybrid approach which has been developed to allow forces to be estimated in operating structures. These developments have increased the ability to extract information from large structures and are highlighted in this presentation.

  9. Additional Revised Push-Up Test Norms for College Students

    ERIC Educational Resources Information Center

    Mozumdar, Arupendra; Liguori, Gary; Baumgartner, Ted A.

    2010-01-01

    The push-up test is commonly used to assess arm and shoulder girdle strength and endurance. Baumgartner, Oh, Chung, and Hales (2002) developed a revised push-up test for college students with a standardized test protocol. The purpose of the present study was to develop percentile norms for the revised push-up test based on the push-up scores of…

  10. Field evaluation of some bait additives against Indian crested porcupine (Hystrix indica) (Rodentia: Hystricidae).

    PubMed

    Mushtaq, Muhammad; Hussain, Iftikhar; Mian, Afsar; Munir, Shahid; Ahmed, Irfan; Khan, Abdul Aziz

    2013-09-01

    This research study evaluated the effect of different additives on the bait consumption by Indian crested porcupine, a serious forest and agricultural pest, under field conditions. Different additives (saccharin, common salt, bone meal, fish meal, peanut butter, egg yolk, egg shell powder, yeast powder, mineral oil and coconut oil) at 2 and 5% each were tested for their relative preference, using groundnut-maize (1:1) as basic bait. All the additives were tested under a no-choice test pattern. For control tests, no additive was mixed with the basic bait. Saccharin at 5% concentration significantly enhanced the consumption of bait over the basic bait, while 2% saccharin supplemented bait resulted in a non-significant bait consumption. All other additives did not enhance the consumption of the bait material; rather, these worked as repellents. However, the repellency was lowest with the common salt, followed by egg yolk, egg shell powder, bone meal, peanut butter, mineral oil, fish meal and yeast powder, while coconut remained the most repellent compound. The present study suggested that groundnut-maize (1:1) supplemented with 5% saccharin was the preferred bait combination, and can be used with different rodenticides for the management of Indian crested porcupine. PMID:24020467

  11. Field evaluation of some bait additives against Indian crested porcupine (Hystrix indica) (Rodentia: Hystricidae).

    PubMed

    Mushtaq, Muhammad; Hussain, Iftikhar; Mian, Afsar; Munir, Shahid; Ahmed, Irfan; Khan, Abdul Aziz

    2013-09-01

    This research study evaluated the effect of different additives on the bait consumption by Indian crested porcupine, a serious forest and agricultural pest, under field conditions. Different additives (saccharin, common salt, bone meal, fish meal, peanut butter, egg yolk, egg shell powder, yeast powder, mineral oil and coconut oil) at 2 and 5% each were tested for their relative preference, using groundnut-maize (1:1) as basic bait. All the additives were tested under a no-choice test pattern. For control tests, no additive was mixed with the basic bait. Saccharin at 5% concentration significantly enhanced the consumption of bait over the basic bait, while 2% saccharin supplemented bait resulted in a non-significant bait consumption. All other additives did not enhance the consumption of the bait material; rather, these worked as repellents. However, the repellency was lowest with the common salt, followed by egg yolk, egg shell powder, bone meal, peanut butter, mineral oil, fish meal and yeast powder, while coconut remained the most repellent compound. The present study suggested that groundnut-maize (1:1) supplemented with 5% saccharin was the preferred bait combination, and can be used with different rodenticides for the management of Indian crested porcupine.

  12. SRS environmental technology development field test platform

    SciTech Connect

    Riha, B.D.; Rossabi, J.; Eddy-Dilek, C.A.

    1995-09-01

    A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper provides an overview of the field test site and a description of some of the technologies demonstrated at the site including their field applications.

  13. Witnessing orifice meter calibration and field testing

    SciTech Connect

    Woods, D.

    1995-12-01

    It would seem with the advent of electronic measurement and electronic custody transfer of natural gas and other petroleum products that witnessing orifice meter calibration and field testing would become an obsolete practice in the petroleum industry. This however, is not the case. Due to low volume measurement, remote locations, dollar cost of electronic measurement, and arrangements between companies regarding electronic custody, transfer, witnessing orifice meter calibration and field testing will continue to be an integral part of the petroleum industry`s future. Even as technology moves forward and electronic measurement becomes common within the petroleum industry, electronic hardware used in measurement will, like the orifice recorder, only be a secondary measuring device. The meter tube and orifice plate will continue to be the primary measuring device. Due to these circumstances witnessing orifice meter calibration and field testing will also continue to be important even though some emphasis will be shifted to witnessing field testing of electronic equipment. The information in this paper is not meant to be an absolute, but, to be used as a guide in witnessing and field testing orifice meters. There are many variables in testing that. due to the length of this paper, will not be discussed.

  14. Trip Report-Produced-Water Field Testing

    SciTech Connect

    Sullivan, Enid J.

    2012-05-25

    Los Alamos National Laboratory (LANL) conducted field testing of a produced-water pretreatment apparatus with assistance from faculty at the Texas A&M University (TAMU) protein separation sciences laboratory located on the TAMU main campus. The following report details all of the logistics surrounding the testing. The purpose of the test was to use a new, commercially-available filter media housing containing modified zeolite (surfactant-modified zeolite or SMZ) porous medium for use in pretreatment of oil and gas produced water (PW) and frac-flowback waters. The SMZ was tested previously in October, 2010 in a lab-constructed configuration ('old multicolumn system'), and performed well for removal of benzene, toluene, ethylbenzene, and xylenes (BTEX) from PW. However, a less-expensive, modular configuration is needed for field use. A modular system will allow the field operator to add or subtract SMZ filters as needed to accommodate site specific conditions, and to swap out used filters easily in a multi-unit system. This test demonstrated the use of a commercial filter housing with a simple flow modification and packed with SMZ for removing BTEX from a PW source in College Station, Texas. The system will be tested in June 2012 at a field site in Pennsylvania for treating frac-flowback waters. The goals of this test are: (1) to determine sorption efficiency of BTEX in the new configuration; and (2) to observe the range of flow rates, backpressures, and total volume treated at a given flow rate.

  15. Field Testing of Environmentally Friendly Drilling System

    SciTech Connect

    David Burnett

    2009-05-31

    The Environmentally Friendly Drilling (EFD) program addresses new low-impact technology that reduces the footprint of drilling activities, integrates light weight drilling rigs with reduced emission engine packages, addresses on-site waste management, optimizes the systems to fit the needs of a specific development sites and provides stewardship of the environment. In addition, the program includes industry, the public, environmental organizations, and elected officials in a collaboration that addresses concerns on development of unconventional natural gas resources in environmentally sensitive areas. The EFD program provides the fundamentals to result in greater access, reasonable regulatory controls, lower development cost and reduction of the environmental footprint associated with operations for unconventional natural gas. Industry Sponsors have supported the program with significant financial and technical support. This final report compendium is organized into segments corresponding directly with the DOE approved scope of work for the term 2005-2009 (10 Sections). Each specific project is defined by (a) its goals, (b) its deliverable, and (c) its future direction. A web site has been established that contains all of these detailed engineering reports produced with their efforts. The goals of the project are to (1) identify critical enabling technologies for a prototype low-impact drilling system, (2) test the prototype systems in field laboratories, and (3) demonstrate the advanced technology to show how these practices would benefit the environment.

  16. Combustion Safety Simplified Test Protocol Field Study

    SciTech Connect

    Brand, L.; Cautley, D.; Bohac, D.; Francisco, P.; Shen, L.; Gloss, S.

    2015-11-01

    Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project team collected field data on 11 houses in 2015.

  17. 40 CFR 63.504 - Additional requirements for performance testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... emission test using the techniques specified in § 63.11(b)(4); (2) Determine the net heating value of the... the Administrator the opportunity to have an observer present during the test. If after 30 days notice... in Method 301, 40 CFR part 63, appendix A. (c) Notwithstanding any other provision of this...

  18. Sultan - forced flow, high field test facility

    SciTech Connect

    Horvath, I.; Vecsey, G.; Weymuth, P.; Zellweger, J.

    1981-09-01

    Three European laboratories: CNEN (Frascati, I) ECN (Petten, NL) and SIN (Villigen, CH) decided to coordinate their development efforts and to install a common high field forced flow test facility at Villigen Switzerland. The test facility SULTAN (Supraleiter Testanlage) is presently under construction. As a first step, an 8T/1m bore solenoid with cryogenic periphery will be ready in 1981. The cryogenic system, data acquisition system and power supplies which are contributed by SIN are described. Experimental feasibilities, including cooling, and instrumentation are reviewed. Progress of components and facility construction is described. Planned extension of the background field up to 12T by insert coils is outlined. 5 refs.

  19. Numerical simulations of capillary barrier field tests

    SciTech Connect

    Morris, C.E.; Stormont, J.C.

    1997-12-31

    Numerical simulations of two capillary barrier systems tested in the field were conducted to determine if an unsaturated flow model could accurately represent the observed results. The field data was collected from two 7-m long, 1.2-m thick capillary barriers built on a 10% grade that were being tested to investigate their ability to laterally divert water downslope. One system had a homogeneous fine layer, while the fine soil of the second barrier was layered to increase its ability to laterally divert infiltrating moisture. The barriers were subjected first to constant infiltration while minimizing evaporative losses and then were exposed to ambient conditions. The continuous infiltration period of the field tests for the two barrier systems was modelled to determine the ability of an existing code to accurately represent capillary barrier behavior embodied in these two designs. Differences between the field test and the model data were found, but in general the simulations appeared to adequately reproduce the response of the test systems. Accounting for moisture retention hysteresis in the layered system will potentially lead to more accurate modelling results and is likely to be important when developing reasonable predictions of capillary barrier behavior.

  20. Cold chain: solar refrigerator field tested.

    PubMed

    1983-04-01

    The Health Ministries of Colombia and Peru, in collaboration with the Expanded Program on Immunization (EPI)/Pan American Health Organization (PAHO) and the Centers for Disease Control (CDC), have begun field testing a solar-powered vaccine refrigerator. The aim of the fields trials is to determine whether solar refrigerators can maintain the temperatures required for vaccine storage (+4-8 degrees Celsius) and produce ice at a rate of 2 kg/24 hours under different environmental conditions. these refrigerators would be particularly useful in areas that lack a consistent supply of good quality fuel or where the electrical supply is intermittent or nonexistent. Full appraisal of this technology will require 2 years of field testing; Colombia and Peru expect to complete testing in 1985. To date, 5 models have passed CDC-developed specifications, all of which are manufactured in the US. PAHO/WHO recommends that health ministries should consider the following guidelines in considering the purchase of a particular system: the initial purchase should be for a limited quantity (about 5) of refrigerators to permit field testing; solar panels should meet specific criteria; consideration should be given only to those models that have passed qualification tests; each unit should be fully equipped with monitoring devices and spare parts; and a trained refrigerator technician should be available to repair the equipment.

  1. Slug tests in wells screened across the water table: some additional considerations.

    PubMed

    Butler, J J

    2014-01-01

    The majority of slug tests done at sites of shallow groundwater contamination are performed in wells screened across the water table and are affected by mechanisms beyond those considered in the standard slug-test models. These additional mechanisms give rise to a number of practical issues that are yet to be fully resolved; four of these are addressed here. The wells in which slug tests are performed were rarely installed for that purpose, so the well design can result in problematic (small signal to noise ratio) test data. The suitability of a particular well design should thus always be assessed prior to field testing. In slug tests of short duration, it can be difficult to identify which portion of the test represents filter-pack drainage and which represents formation response; application of a mass balance can help confirm that test phases have been correctly identified. A key parameter required for all slug test models is the casing radius. However, in this setting, the effective casing radius (borehole radius corrected for filter-pack porosity), not the nominal well radius, is required; this effective radius is best estimated directly from test data. Finally, although conventional slug-test models do not consider filter-pack drainage, these models will yield reasonable hydraulic conductivity estimates when applied to the formation-response phase of a test from an appropriately developed well.

  2. 40 CFR 63.1352 - Additional test methods.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... determine the rates of emission of hydrogen chloride (HCl) from kilns, in-line kiln/raw mills and associated... operators conducting tests to determine the rates of emission of hydrogen chloride (HCl) from kilns,...

  3. Testing Nested Additive, Multiplicative, and General Multitrait-Multimethod Models.

    ERIC Educational Resources Information Center

    Coenders, Germa; Saris, Willem E.

    2000-01-01

    Provides alternatives to the definitions of additive and multiplicative method effects in multitrait-multimethod data given by D. Campbell and E. O'Connell (1967). The alternative definitions can be formulated by means of constraints in the parameters of the correlated uniqueness model (H. Marsh, 1989). (SLD)

  4. STIS Sparse Field CTE test {Cycle 9}

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    2000-07-01

    CTE measurements are made using the "sparse field test", along both the serial and parallel axes. This program needs special commanding to provide {a} off-center MSM positionings of some slits, and {b} the ability to read out with any amplifier {A, B, C, or D}. All exposures are internals.

  5. STIS Sparse Field CTE test {Cycle 8}

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    1999-07-01

    CTE measurements are made using the "sparse field test", along both the serial and parallel axes. This program needs special commanding to provide {a} off-center MSM positionings of some slits, and {b} the ability to read out with any amplifier {A, B, C, or D}. All exposures are internals.

  6. Comparative Field Tests of Pressurised Rover Prototypes

    NASA Astrophysics Data System (ADS)

    Mann, G. A.; Wood, N. B.; Clarke, J. D.; Piechochinski, S.; Bamsey, M.; Laing, J. H.

    The conceptual designs, interior layouts and operational performances of three pressurised rover prototypes - Aonia, ARES and Everest - were field tested during a recent simulation at the Mars Desert Research Station in Utah. A human factors experiment, in which the same crew of three executed the same simulated science mission in each of the three vehicles, yielded comparative data on the capacity of each vehicle to safely and comfortably carry explorers away from the main base, enter and exit the vehicle in spacesuits, perform science tasks in the field, and manage geological and biological samples. As well as offering recommendations for design improvements for specific vehicles, the results suggest that a conventional Sports Utility Vehicle (SUV) would not be suitable for analog field work; that a pressurised docking tunnel to the main habitat is essential; that better provisions for spacesuit storage are required; and that a crew consisting of one driver/navigator and two field science crew specialists may be optimal. From a field operations viewpoint, a recurring conflict between rover and habitat crews at the time of return to the habitat was observed. An analysis of these incidents leads to proposed refinements of operational protocols, specific crew training for rover returns and again points to the need for a pressurised docking tunnel. Sound field testing, circulating of results, and building the lessons learned into new vehicles is advocated as a way of producing ever higher fidelity rover analogues.

  7. 40 CFR 63.504 - Additional requirements for performance testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... in Method 301, 40 CFR part 63, appendix A. (c) Notwithstanding any other provision of this subpart... customer; or necessitating that the owner or operator make product in excess of demand. (2) References in... emission test using the techniques specified in § 63.11(b)(4); (2) Determine the net heating value of...

  8. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... methods shall be validated according to the protocol in Method 301, 40 CFR part 63, appendix A. (c... necessitating that the owner or operator make a product in excess of demand. (iii) Causing plant or testing... General Provisions; (2) Determine the net heating value of the gas being combusted, using the...

  9. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... protocol in Method 301, 40 CFR part 63, appendix A. (c) Notwithstanding any other provision of this subpart... demand. (iii) Causing plant or testing personnel to be subject to unsafe conditions. Owners or operators... the techniques specified in § 63.11(b)(4) of the General Provisions; (2) Determine the net...

  10. 40 CFR 63.504 - Additional requirements for performance testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... in Method 301, 40 CFR part 63, appendix A. (c) Notwithstanding any other provision of this subpart... customer; or necessitating that the owner or operator make product in excess of demand. (2) References in... emission test using the techniques specified in § 63.11(b)(4); (2) Determine the net heating value of...

  11. Large-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Daniel, Richard C.; Gauglitz, Phillip A.; Burns, Carolyn A.; Fountain, Matthew S.; Shimskey, Rick W.; Billing, Justin M.; Bontha, Jagannadha R.; Kurath, Dean E.; Jenks, Jeromy WJ; MacFarlan, Paul J.; Mahoney, Lenna A.

    2013-08-01

    One of the events postulated in the hazard analysis for the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak event involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids that behave as a Newtonian fluid. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and in processing facilities across the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are mostly absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale testing. The small-scale testing and resultant data are described in Mahoney et al. (2012b), and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used

  12. Small-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Schonewill, Philip P.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, G. N.; Mahoney, Lenna A.; Tran, Diana N.; Burns, Carolyn A.; Kurath, Dean E.

    2013-08-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are largely absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale. The small-scale testing and resultant data are described in Mahoney et al. (2012b) and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used to mimic the

  13. Goldstone field test activities: Target search

    NASA Technical Reports Server (NTRS)

    Tarter, J.

    1986-01-01

    In March of this year prototype SETI equipment was installed at DSS13, the 26 meter research and development antenna at NASA's Goldstone complex of satellite tracking dishes. The SETI equipment will remain at this site at least through the end of the summer so that the hardware and software developed for signal detection and recognition can be fully tested in a dynamic observatory environment. The field tests are expected to help understand which strategies for observing and which signal recognition algorithms perform best in the presence of strong man-made interfering signals (RFI) and natural astronomical sources.

  14. ADDITIVE TESTING FOR IMPROVED SULFUR RETENTION: PRELIMINARY REPORT

    SciTech Connect

    Amoroso, J.; Fox, K.

    2011-09-07

    The Savannah River National Laboratory is collaborating with Alfred University to evaluate the potential for additives in borosilicate glass to improve sulfur retention. This preliminary report provides further background on the incorporation of sulfur in glass and outlines the experiments that are being performed by the collaborators. A simulated waste glass composition has been selected for the experimental studies. The first phase of experimental work will evaluate the impacts of BaO, PbO, and V{sub 2}O{sub 5} at concentrations of 1.0, 2.0, and 5.0 wt % on sulfate retention in simulated high level waste borosilicate glass. The second phase of experimental work will evaluate the effects of time at the melt temperature on sulfur retention. The resulting samples will be characterized to determine the amount of sulfur remaining as well as to identify the formation of any crystalline phases. The results will be used to guide the future selection of frits and glass forming chemicals in vitrifying Department of Energy wastes containing high sulfur concentrations.

  15. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E.; Hietala, J.; Wendland, R.D.; Collins, F.

    1992-07-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  16. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E. ); Hietala, J. ); Wendland, R.D. ); Collins, F. )

    1992-01-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  17. Field Test Kit for Gun Residue Detection

    SciTech Connect

    WALKER, PAMELA K.; RODACY, PHILIP J.

    2002-01-01

    One of the major needs of the law enforcement field is a product that quickly, accurately, and inexpensively identifies whether a person has recently fired a gun--even if the suspect has attempted to wash the traces of gunpowder off. The Field Test Kit for Gunshot Residue Identification based on Sandia National Laboratories technology works with a wide variety of handguns and other weaponry using gunpowder. There are several organic chemicals in small arms propellants such as nitrocellulose, nitroglycerine, dinitrotoluene, and nitrites left behind after the firing of a gun that result from the incomplete combustion of the gunpowder. Sandia has developed a colorimetric shooter identification kit for in situ detection of gunshot residue (GSR) from a suspect. The test kit is the first of its kind and is small, inexpensive, and easily transported by individual law enforcement personnel requiring minimal training for effective use. It will provide immediate information identifying gunshot residue.

  18. Combustion Safety Simplified Test Protocol Field Study

    SciTech Connect

    Brand, L; Cautley, D.; Bohac, D.; Francisco, P.; Shen, L.; Gloss, S.

    2015-11-05

    "9Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project provides several key results. State weatherization agencies do not generally track combustion safety failures, the data from those that do suggest that there is little actual evidence that combustion safety failures due to spillage from non-dryer exhaust are common and that only a very small number of homes are subject to the failures. The project team collected field data on 11 houses in 2015. Of these homes, two houses that demonstrated prolonged and excessive spillage were also the only two with venting systems out of compliance with the National Fuel Gas Code. The remaining homes experienced spillage that only occasionally extended beyond the first minute of operation. Combustion zone depressurization, outdoor temperature, and operation of individual fans all provide statistically significant predictors of spillage.

  19. Field testing plan for unsaturated zone monitoring and field studies

    SciTech Connect

    Young, M.H.; Wierenga, P.J.; Warrick, A.W.

    1996-10-01

    The University of Arizona, in cooperation with the Bureau of Economic Geology at The University of Texas at Austin, and Stephens and Associates in Albuquerque, New Mexico has developed a field testing plan for evaluating subsurface monitoring systems. The U.S. Nuclear Regulatory Commission has requested development of these testing plans for low-level radioactive waste disposal sites (LLW) and for monitoring at decommissioned facilities designated under the {open_quotes}Site Decommissioning Management Plan{close_quotes} (SDMP). The tests are conducted on a 50 m by 50 m plot on the University of Arizona`s Maricopa Agricultural Center. Within the 50 m by 50 m plot one finds: (1) an instrumented buried trench, (2) monitoring islands similar to those proposed for the Ward Valley, California LLW Facility, (3) deep borehole monitoring sites, (4) gaseous transport monitoring, and (5) locations for testing non-invasive geophysical measurement techniques. The various subplot areas are instrumented with commercially available instruments such as neutron probes, time domain reflectometry probes, tensiometers, psychrometers, heat dissipation sensors, thermocouples, solution samplers, and cross-hole geophysics electrodes. Measurement depths vary from ground surface to 15 m. The data from the controlled flow and transport experiments, conducted over the plot, will be used to develop an integrated approach to long-term monitoring of the vadose zone at waste disposal sites. The data will also be used to test field-scale flow and transport models. This report describes in detail the design of the experiment and the methodology proposed for evaluating the data.

  20. A new method of field MRTD test

    NASA Astrophysics Data System (ADS)

    Chen, Zhibin; Song, Yan; Liu, Xianhong; Xiao, Wenjian

    2014-09-01

    MRTD is an important indicator to measure the imaging performance of infrared camera. In the traditional laboratory test, blackbody is used as simulated heat source which is not only expensive and bulky but also difficult to meet field testing requirements of online automatic infrared camera MRTD. To solve this problem, this paper introduces a new detection device for MRTD, which uses LED as a simulation heat source and branded plated zinc sulfide glass carved four-bar target as a simulation target. By using high temperature adaptability cassegrain collimation system, the target is simulated to be distance-infinite so that it can be observed by the human eyes to complete the subjective test, or collected to complete objective measurement by image processing. This method will use LED to replace blackbody. The color temperature of LED is calibrated by thermal imager, thereby, the relation curve between the LED temperature controlling current and the blackbody simulation temperature difference is established, accurately achieved the temperature control of the infrared target. Experimental results show that the accuracy of the device in field testing of thermal imager MRTD can be limited within 0.1K, which greatly reduces the cost to meet the project requirements with a wide application value.

  1. Bistatic radar sea state monitoring field test

    NASA Technical Reports Server (NTRS)

    Ruck, G. T.; Kirchbaum, G. K.; Everly, J. O.

    1975-01-01

    Recent advances in understanding the physical phenomena controlling the interaction of electromagnetic energy with the ocean surface have revealed the possiblity of remote measurement of the two-dimensional surface wave height spectrum of the ocean using bistatic radar techniques. The basic feasibility of such a technique operating at frequencies in the HF region (3 to 30 MHz) was examined during previous studies and hardware for an experimental verification experiment was specified. The activities have resulted in a determination of the required hardware and system parameters for both satellite and aircraft systems, the development, assembly, and testing of hardware for an experimental aircraft system, the development and initial testing of data processing procedures, and the conduct of an initial flight test experiment. Activities were devoted to completing the assembly and testing of the experimental hardware, completing the experiment planning, conducting a field test experiment, and the processing and analysis of the experimental data. Even though directional spectrum maps of the test area cannot be generated from the measured data, the hardware concept employed appears viable, and solutions to the problems encountered have been identified.

  2. Preliminary Results of Field Emission Cathode Tests

    NASA Technical Reports Server (NTRS)

    Sovey, James S.; Kovaleski, Scott D.

    2001-01-01

    Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

  3. In Situ Field Testing of Processes

    SciTech Connect

    J. Wang

    2001-12-14

    The purpose of this Analysis/Model Report (AMR) is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts of the Yucca Mountain Site Characterization Project (YMP). This revision updates data and analyses presented in the initial issue of this AMR. This AMR was developed in accordance with the ''Technical Work Plan for Unsaturated Zone (UZ) Flow and Transport Process Model Report'' and ''Technical Work Plan for UZ Flow, Transport, and Coupled Processes Process Model Report. These activities were performed to investigate in situ flow and transport processes. The evaluations provide the necessary framework to: (1) refine and confirm the conceptual model of matrix and fracture processes in the unsaturated zone (UZ) and (2) analyze the impact of excavation (including use of construction water and effect of ventilation) on the UZ flow and transport processes. This AMR is intended to support revisions to ''Conceptual and Numerical Models for UZ Flow and Transport'' and ''Unsaturated Zone Flow and Transport Model Process Model Report''. In general, the results discussed in this AMR are from studies conducted using a combination or a subset of the following three approaches: (1) air-injection tests, (2) liquid-release tests, and (3) moisture monitoring using in-drift sensors or in-borehole sensors, to evaluate the impact of excavation, ventilation, and construction-water usage on the surrounding rocks. The liquid-release tests and air-injection tests provide an evaluation of in situ fracture flow and the competing processes of matrix imbibition. Only the findings from testing and data not covered in the ''Seepage Calibration Model and Seepage Testing Data'' are analyzed in detail in the AMR.

  4. Issues related to field testing in tuff

    SciTech Connect

    Zimmerman, R.M.

    1982-12-31

    This paper has brought out the unique properties of tuffs and related them to needs associated with their use as a host rock for a high level nuclear waste repository. Major issues of temperature, pore water, joints, and depositional patterns have been identified and related responses and impacts outlined in Table 1. Planned experiments have been outlined and their relationships to the rock mechanics issues summarized in Table 2. The conclusions from this paper are: (1) tuff is a complex rock and basic phenomenological understanding is incomplete; and (2) available field test facilities will be used for a series of experiments designed to improve phenomenological understanding and support repository design efforts.

  5. CHARMM additive and polarizable force fields for biophysics and computer-aided drug design

    PubMed Central

    Vanommeslaeghe, K.

    2014-01-01

    Background Molecular Mechanics (MM) is the method of choice for computational studies of biomolecular systems owing to its modest computational cost, which makes it possible to routinely perform molecular dynamics (MD) simulations on chemical systems of biophysical and biomedical relevance. Scope of Review As one of the main factors limiting the accuracy of MD results is the empirical force field used, the present paper offers a review of recent developments in the CHARMM additive force field, one of the most popular bimolecular force fields. Additionally, we present a detailed discussion of the CHARMM Drude polarizable force field, anticipating a growth in the importance and utilization of polarizable force fields in the near future. Throughout the discussion emphasis is placed on the force fields’ parametrization philosophy and methodology. Major Conclusions Recent improvements in the CHARMM additive force field are mostly related to newly found weaknesses in the previous generation of additive force fields. Beyond the additive approximation is the newly available CHARMM Drude polarizable force field, which allows for MD simulations of up to 1 microsecond on proteins, DNA, lipids and carbohydrates. General Significance Addressing the limitations ensures the reliability of the new CHARMM36 additive force field for the types of calculations that are presently coming into routine computational reach while the availability of the Drude polarizable force fields offers a model that is an inherently more accurate model of the underlying physical forces driving macromolecular structures and dynamics. PMID:25149274

  6. 3X-100 blade field test.

    SciTech Connect

    Zayas, Jose R.; Johnson, Wesley D.

    2008-03-01

    In support of a Work-For-Other (WFO) agreement between the Wind Energy Technology Department at Sandia National Laboratories and 3TEX, one of the three Micon 65/13M wind turbines at the USDA Agriculture Research Service (ARS) center in Bushland, Texas, has been used to test a set of 9 meter wind turbine blades, manufactured by TPI composites using the 3TEX carbon material for the spar cap. Data collected from the test has been analyzed to evaluate both the aerodynamic performance and the structural response from the blades. The blades aerodynamic and structural performance, the meteorological inflow and the wind turbine structural response has been monitored with an array of 57 instruments: 15 to characterize the blades, 13 to characterize inflow, and 15 to characterize the time-varying state of the turbine. For the test, data was sampled at a rate of 40 Hz using the ATLAS II (Accurate GPS Time-Linked Data Acquisition System) data acquisition system. The system features a time-synchronized continuous data stream and telemetered data from the turbine rotor. This paper documents the instruments and infrastructure that have been developed to monitor these blades, turbines and inflow, as well as both modeling and field testing results.

  7. Transferability and additivity of dihedral parameters in polarizable and nonpolarizable empirical force fields.

    PubMed

    Zgarbová, Marie; Rosnik, Andreana M; Luque, F Javier; Curutchet, Carles; Jurečka, Petr

    2015-09-30

    Recent advances in polarizable force fields have revealed that major reparameterization is necessary when the polarization energy is treated explicitly. This study is focused on the torsional parameters, which are crucial for the accurate description of conformational equilibria in biomolecules. In particular, attention is paid to the influence of polarization on the (i) transferability of dihedral terms between molecules, (ii) transferability between different environments, and (iii) additivity of dihedral energies. To this end, three polarizable force fields based on the induced point dipole model designed for use in AMBER are tested, including two recent ff02 reparameterizations. Attention is paid to the contributions due to short range interactions (1-2, 1-3, and 1-4) within the four atoms defining the dihedral angle. The results show that when short range 1-2 and 1-3 polarization interactions are omitted, as for instance in ff02, the 1-4 polarization contribution is rather small and unlikely to improve the description of the torsional energy. Conversely, when screened 1-2 and 1-3 interactions are included, the polarization contribution is sizeable and shows potential to improve the transferability of parameters between different molecules and environments as well as the additivity of dihedral terms. However, to reproduce intramolecular polarization effects accurately, further fine-tuning of the short range damping of polarization is necessary.

  8. Transferability and additivity of dihedral parameters in polarizable and nonpolarizable empirical force fields.

    PubMed

    Zgarbová, Marie; Rosnik, Andreana M; Luque, F Javier; Curutchet, Carles; Jurečka, Petr

    2015-09-30

    Recent advances in polarizable force fields have revealed that major reparameterization is necessary when the polarization energy is treated explicitly. This study is focused on the torsional parameters, which are crucial for the accurate description of conformational equilibria in biomolecules. In particular, attention is paid to the influence of polarization on the (i) transferability of dihedral terms between molecules, (ii) transferability between different environments, and (iii) additivity of dihedral energies. To this end, three polarizable force fields based on the induced point dipole model designed for use in AMBER are tested, including two recent ff02 reparameterizations. Attention is paid to the contributions due to short range interactions (1-2, 1-3, and 1-4) within the four atoms defining the dihedral angle. The results show that when short range 1-2 and 1-3 polarization interactions are omitted, as for instance in ff02, the 1-4 polarization contribution is rather small and unlikely to improve the description of the torsional energy. Conversely, when screened 1-2 and 1-3 interactions are included, the polarization contribution is sizeable and shows potential to improve the transferability of parameters between different molecules and environments as well as the additivity of dihedral terms. However, to reproduce intramolecular polarization effects accurately, further fine-tuning of the short range damping of polarization is necessary. PMID:26224547

  9. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Retention of samples and additional testing. 199... SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a... period, the employee or the employee's representative, the operator, the Administrator, or, if...

  10. Addition of magnetic field capability to existing extremely-low-frequency electric field exposure systems.

    PubMed

    Miller, D L; Miller, M C; Kaune, W T

    1989-01-01

    Magnetic field systems were added to existing electric field exposure apparatuses for exposing cell suspensions in vitro and small animals in vivo. Two horizontally oriented, rectangular coils, stacked one directly above the other, have opposite electric currents. This configuration minimizes leakage fields and allows sham- and field-exposure systems to be placed in the same room or incubator. For the in vitro system, copper plates formed the loop-pair, with up to 900 A supplied by a 180:1 transformer. Electric fields were supplied via electrodes at the ends of cell-culture tubes, eight of which can be accommodated by each exposure system. Two complete systems are situated in an incubator to allow simultaneous sham and field exposure up to 1 mT. For the in vivo system, four pairs of 0.8 x 2.7-m coils made of copper bus bar are employed. This arrangement is energized from the power grid via a 30:1 transformer; horizontal magnetic flux densities up to 1 mT can be generated. Pairs of electrode plates spaced 30.5 cm apart provide electric field exposure of up to 130 kV/m. Four systems with a capacity of 48 rats each are located in one room. For both the in vitro and in vivo systems, magnetic exposure fields are uniform to within +/- 2.5%, and sham levels are at least 2,500-fold lower than exposure levels. Potential confounding factors, such as heating and vibration, were examined and found to be minimal. PMID:2712843

  11. FIELD TEST OF THE FLAME QUALITY INDICATOR

    SciTech Connect

    Rudin, Andrew M; Butcher, Thomas; Troost, Henry

    2003-02-04

    The flame quality indicator concept was developed at BNL specifically to monitor the brightness of the flame in a small oil burner and to provide a ''call for service'' notification when the brightness has changed from its setpoint, either high or low. In prior development work BNL has explored the response of this system to operational upsets such as excess air changes, fouled atomizer nozzles, poor fuel quality, etc. Insight Technologies, Inc. and Honeywell, Inc. have licensed this technology from the U.S. Department of Energy and have been cooperating to develop product offerings which meet industry needs with an optimal combination of function and price. Honeywell has recently completed the development of the Flame Quality Monitor (FQM or Honeywell QS7100F). This is a small module which connects via a serial cable to the burners primary operating control. Primary advantages of this approach are simplicity, cost, and ease of installation. Call-for-service conditions are output in the form of front panel indicator lights and contact closure which can trigger a range of external communication options. Under this project a field test was conducted of the FQM in cooperation with service organizations in Virginia, Pennsylvania, New Jersey, New York, and Connecticut. At total of 83 field sites were included. At each site the FQM was installed in parallel with another embodiment of this concept--the Insight AFQI. The AFQI incorporates a modem and provides the ability to provide detailed information on the trends in the flame quality over the course of the two year test period. The test site population was comprised of 79.5% boilers, 13.7% warm air furnaces, and 6.8% water heaters. Nearly all were of residential size--with firing rates ranging from 0.6 gallons of oil per hour to 1.25. During the course of the test program the monitoring equipment successfully identified problems including: plugged fuel lines, fouled nozzles, collapsed combustion chambers, and poor fuel

  12. Cooperative field test program for wind systems

    SciTech Connect

    Bollmeier, W.S. II; Dodge, D.M.

    1992-03-01

    The objectives of the Federal Wind Energy Program, managed by the US Department of Energy (DOE), are (1) to assist industry and utilities in achieving a multi-regional US market penetration of wind systems, and (2) to establish the United States as the world leader in the development of advanced wind turbine technology. In 1984, the program conducted a series of planning workshops with representatives from the wind energy industry to obtain input on the Five-Year Research Plan then being prepared by DOE. One specific suggestion that came out of these meetings was that the federal program should conduct cooperative research tests with industry to enhance the technology transfer process. It was also felt that the active involvement of industry in DOE-funded research would improve the state of the art of wind turbine technology. DOE established the Cooperative Field Test Program (CFTP) in response to that suggestion. This program was one of the first in DOE to feature joint industry-government research test teams working toward common objectives.

  13. Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

    NASA Technical Reports Server (NTRS)

    Fikes, John C.

    2014-01-01

    The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

  14. 40 CFR 1065.935 - Emission test sequence for field testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Emission test sequence for field... Systems § 1065.935 Emission test sequence for field testing. (a) Time the start of field testing as.... Start the field test within 20 min of engine shutdown. (3) If the standard-setting part requires...

  15. 40 CFR 1065.935 - Emission test sequence for field testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Emission test sequence for field... Systems § 1065.935 Emission test sequence for field testing. (a) Time the start of field testing as.... Start the field test within 20 min of engine shutdown. (3) If the standard-setting part requires...

  16. 40 CFR 1065.935 - Emission test sequence for field testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Emission test sequence for field... Systems § 1065.935 Emission test sequence for field testing. (a) Time the start of field testing as.... Start the field test within 20 min of engine shutdown. (3) If the standard-setting part requires...

  17. 40 CFR 1065.935 - Emission test sequence for field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Emission test sequence for field... Systems § 1065.935 Emission test sequence for field testing. (a) Time the start of field testing as.... Start the field test within 20 min of engine shutdown. (3) If the standard-setting part requires...

  18. 40 CFR 1065.925 - PEMS preparation for field testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false PEMS preparation for field testing. 1065.925 Section 1065.925 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement Systems § 1065.925 PEMS preparation for field testing....

  19. Field testing method for photovaltaic modules

    NASA Astrophysics Data System (ADS)

    Ramos, Gerber N.

    For remote areas, where solar photovoltaic modules are the only source of power, it is essential to perform preventive maintenance to insure that the PV system works properly; unfortunately, prices for PV testers range from 1,700 to 8,000. To address this issue, a portable inexpensive tester and analysis methodology have been developed. Assembling a simple tester, which costs $530 and weighs about 5 pounds, and using the Four-Parameters PV Model, we characterized the current-voltage (I-V) curve at environmental testing conditions; and then employing radiation, temperature, and age degradation sensitivity equations, we extrapolated the I-V curve to standard testing conditions. After applying the methodology to three kinds of silicon modules (mono-crystalline, multi-crystalline, and thin-film), we obtained maximum power points up to 97% of the manufacturer's specifications. Therefore, based on these results, it is reasonably accurate and affordable to verify the performance of solar modules in the field.

  20. 46 CFR 160.035-12 - Additional preapproval tests required for F.R.P. lifeboats.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 6 2011-10-01 2011-10-01 false Additional preapproval tests required for F.R.P... Merchant Vessels § 160.035-12 Additional preapproval tests required for F.R.P. lifeboats. (a) General... p.s.i. of air pressure both before and after the tests described in paragraphs (b)(1) through (6)...

  1. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 34 Education 3 2010-07-01 2010-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process § 668.148 Additional criteria for the approval of certain tests. Except as provided in § 668.143— (a)...

  2. LPT. Shield test facility (TAN646) interior. Addition of third steam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) interior. Addition of third steam generator. Burner end. Camera facing southwest. Photographer: Comiskey. Date: January 20, 1965. INEEL negative no. 65-242 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  3. A possible field test for marine cloud brightening geoengineering. A possible field test for marine cloud brightening geoengineering

    NASA Astrophysics Data System (ADS)

    Gadian, A.; Wood, R.; Coe, H.; Latham, J.

    2011-12-01

    A possible field test for marine cloud brightening geoengineering. Abstract: The Marine Cloud Brightening (MCB) geoengineering technique (Latham et al 2008) hypothesizes that seeding marine stratocumulus clouds with copious quantities of roughly monodisperse sub-micrometre seawater particles can enhance the cloud droplet number concentration and increase cloud albedo. Here, we propose a set of field tests to critically assess the efficacy of the MCB geoengineering proposal over a limited area. The tests are de minimus with respect to their climate effects. The tests involve three phases, with increasing logistical complexity, each of which is designed to test one or more important components of the cloud brightening scheme. Each involves the introduction and monitoring of controlled aerosol perturbations from one or more ship-based seeding platforms up to a limited area of 100x100 km2. A suite of observational platforms of increasing number and complexity, including aircraft, ships and satellites, will observe the aerosol plume and in the later experiments the cloud and albedo responses to the aerosol perturbations. These responses must include the necessary cloud physical and chemical processes which determine the efficacy of the cloud brightening scheme. Since these processes are also central to the broader problem of aerosol-cloud-climate interactions, such field tests would have significant benefits for climate science in addition to providing a critical test of the MCB hypothesis. Such field experiments should be designed and conducted in an objective manner within the framework of emerging geoengineering research governance structures. Reference: Latham J. et al.. (2008) Global temperature stabilization via controlled albedo enhancement of low-level maritime clouds. Phil. Trans. R. Soc. A doi:10.1098/rsta.2008.0137

  4. The influence of bioaugmentation and biosurfactant addition on bioremediation efficiency of diesel-oil contaminated soil: feasibility during field studies.

    PubMed

    Szulc, Alicja; Ambrożewicz, Damian; Sydow, Mateusz; Ławniczak, Łukasz; Piotrowska-Cyplik, Agnieszka; Marecik, Roman; Chrzanowski, Łukasz

    2014-01-01

    The study focused on assessing the influence of bioaugmentation and addition of rhamnolipids on diesel oil biodegradation efficiency during field studies. Initial laboratory studies (measurement of emitted CO2 and dehydrogenase activity) were carried out in order to select the consortium for bioaugmentation as well as to evaluate the most appropriate concentration of rhamnolipids. The selected consortium consisted of following bacterial taxa: Aeromonas hydrophila, Alcaligenes xylosoxidans, Gordonia sp., Pseudomonas fluorescens, Pseudomonas putida, Rhodococcus equi, Stenotrophomonas maltophilia, Xanthomonas sp. It was established that the application of rhamnolipids at 150 mg/kg of soil was most appropriate in terms of dehydrogenase activity. Based on the obtained results, four treatment methods were designed and tested during 365 days of field studies: I) natural attenuation; II) addition of rhamnolipids; III) bioaugmentation; IV) bioaugmentation and addition of rhamnolipids. It was observed that bioaugmentation contributed to the highest diesel oil biodegradation efficiency, whereas the addition of rhamnolipids did not notably influence the treatment process.

  5. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2013-07-01 2013-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  6. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2014-07-01 2014-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  7. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2012-07-01 2012-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  8. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2011-07-01 2011-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  9. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  10. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  11. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  12. Field testing of asphalt-emulsion radon-barrier system

    SciTech Connect

    Hartley, J.N.; Freeman, H.D.; Baker, E.G.; Elmore, M.R.; Nelson, D.A.; Voss, C.F.; Koehmstedt, P.L.

    1981-09-01

    Three years of laboratory and field testing have demonstrated that asphalt emulsion seals are effective radon diffusion barriers. Both laboratory and field tests in 1979, 1980 and 1981 have shown that an asphalt emulsion seal can reduce radon fluxes by greater than 99.9%. The effective diffusion coefficient for the various asphalt emulsion admix seals averages about 10/sup -6/ cm/sup 2//s. The 1981 joint field test is a culmination of all the technology developed to date for asphalt emulsion radon barrier systems. Preliminary results of this field test and the results of the 1980 field test are presented. 18 figures, 6 tables.

  13. Field Accuracy Test of Rpas Photogrammetry

    NASA Astrophysics Data System (ADS)

    Barry, P.; Coakley, R.

    2013-08-01

    Baseline Surveys Ltd is a company which specialises in the supply of accurate geospatial data, such as cadastral, topographic and engineering survey data to commercial and government bodies. Baseline Surveys Ltd invested in aerial drone photogrammetric technology and had a requirement to establish the spatial accuracy of the geographic data derived from our unmanned aerial vehicle (UAV) photogrammetry before marketing our new aerial mapping service. Having supplied the construction industry with survey data for over 20 years, we felt that is was crucial for our clients to clearly understand the accuracy of our photogrammetry so they can safely make informed spatial decisions, within the known accuracy limitations of our data. This information would also inform us on how and where UAV photogrammetry can be utilised. What we wanted to find out was the actual accuracy that can be reliably achieved using a UAV to collect data under field conditions throughout a 2 Ha site. We flew a UAV over the test area in a "lawnmower track" pattern with an 80% front and 80% side overlap; we placed 45 ground markers as check points and surveyed them in using network Real Time Kinematic Global Positioning System (RTK GPS). We specifically designed the ground markers to meet our accuracy needs. We established 10 separate ground markers as control points and inputted these into our photo modelling software, Agisoft PhotoScan. The remaining GPS coordinated check point data were added later in ArcMap to the completed orthomosaic and digital elevation model so we could accurately compare the UAV photogrammetry XYZ data with the RTK GPS XYZ data at highly reliable common points. The accuracy we achieved throughout the 45 check points was 95% reliably within 41 mm horizontally and 68 mm vertically and with an 11.7 mm ground sample distance taken from a flight altitude above ground level of 90 m.The area covered by one image was 70.2 m × 46.4 m, which equals 0.325 Ha. This finding has shown

  14. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a) Samples that yield positive results on confirmation must be retained by the laboratory in properly...

  15. Deep Borehole Field Test Requirements and Controlled Assumptions.

    SciTech Connect

    Hardin, Ernest

    2015-07-01

    This document presents design requirements and controlled assumptions intended for use in the engineering development and testing of: 1) prototype packages for radioactive waste disposal in deep boreholes; 2) a waste package surface handling system; and 3) a subsurface system for emplacing and retrieving packages in deep boreholes. Engineering development and testing is being performed as part of the Deep Borehole Field Test (DBFT; SNL 2014a). This document presents parallel sets of requirements for a waste disposal system and for the DBFT, showing the close relationship. In addition to design, it will also inform planning for drilling, construction, and scientific characterization activities for the DBFT. The information presented here follows typical preparations for engineering design. It includes functional and operating requirements for handling and emplacement/retrieval equipment, waste package design and emplacement requirements, borehole construction requirements, sealing requirements, and performance criteria. Assumptions are included where they could impact engineering design. Design solutions are avoided in the requirements discussion. Deep Borehole Field Test Requirements and Controlled Assumptions July 21, 2015 iv ACKNOWLEDGEMENTS This set of requirements and assumptions has benefited greatly from reviews by Gordon Appel, Geoff Freeze, Kris Kuhlman, Bob MacKinnon, Steve Pye, David Sassani, Dave Sevougian, and Jiann Su.

  16. Results of field testing the cement evaluation tool

    SciTech Connect

    Leigh, C.A.; Finlayson, C.G.; Van der Kolk, C.

    1984-01-01

    The Cement Evaluation Tool (CET) developed by Schlumberger employs a pulse-echo technique using eight sonic transducers to investigate the casing cement bond. The tool has been widely field tested in a clastic environment in Brunei (N.W. Borneo), across both oil and gas bearing reservoirs. Numerous comparisons of the CET with conventional CBL/VDL logs have been made. Across oil and water bearing intervals the CET is shown to compare favourably with the CBL/VDL and yields significant additional information on channeling, cement distribution, and the success of casing centralization. In addition, the accuracy of the acoustic calipers have proved sufficient to be used in assisting drilling and completion operations. The response of the tool to a microannulus has also been demonstrated by multiple runs under varying wellbore pressures.

  17. The application of additive technologies in creation a medical simulator-trainer of the human head operating field

    NASA Astrophysics Data System (ADS)

    Kashapov, L. N.; Kashapov, N. F.; Kashapov, R. N.; Pashaev, B. Y.

    2016-06-01

    The aim of the work was to determine the possible application of additive manufacturing technology during the manufacturing process as close as possible to reality of medical simulator-trainers. In work were used some additive manufacturing technologies: selective laser sintering (SLS), fused deposition modeling (FDM), binder Jetting. As a result, a prototype of simulator-trainer of the human head operating field, which based on the CT real patient, was manufactured and conducted its tests. It was found that structure, which is obtained with the use of 3D-printers ProJet 160, most appropriate and closest to the real properties of the bone.

  18. Magnetic Field Apparatus (MFA) Hardware Test

    NASA Technical Reports Server (NTRS)

    Anderson, Ken; Boody, April; Reed, Dave; Wang, Chung; Stuckey, Bob; Cox, Dave

    1999-01-01

    The objectives of this study are threefold: (1) Provide insight into water delivery in microgravity and determine optimal germination paper wetting for subsequent seed germination in microgravity; (2) Observe the behavior of water exposed to a strong localized magnetic field in microgravity; and (3) Simulate the flow of fixative (using water) through the hardware. The Magnetic Field Apparatus (MFA) is a new piece of hardware slated to fly on the Space Shuttle in early 2001. MFA is designed to expose plant tissue to magnets in a microgravity environment, deliver water to the plant tissue, record photographic images of plant tissue, and deliver fixative to the plant tissue.

  19. Laboratory and field testing of improved geothermal rock bits

    SciTech Connect

    Hendrickson, R.R.; Jones, A.H.; Winzenried, R.W.; Maish, A.B.

    1980-07-01

    The development and testing of 222 mm (8-3/4 inch) unsealed, insert type, medium hard formation, high-temperature bits are described. The new bits were fabricated by substituting improved materials in critical bit components. These materials were selected on bases of their high temperature properties, machinability, and heat treatment response. Program objectives required that both machining and heat treating could be accomplished with existing rock bit production equipment. Two types of experimental bits were subjected to laboratory air drilling tests at 250/sup 0/C (482/sup 0/F) in cast iron. These tests indicated field testing could be conducted without danger to the hole, and that bearing wear would be substantially reduced. Six additional experimental bits, and eight conventional bits were then subjected to air drilling a 240/sup 0/C (464/sup 0/F) in Francisan Graywacke at The Geysers, CA. The materials selected improved roller wear by 200%, friction-pin wear by 150%, and lug wear by 150%. Geysers drilling performances compared directly to conventional bits indicate that in-gage drilling life was increased by 70%. All bits at The Geysers are subjected to reaming out-of-gage hole prior to drilling. Under these conditions the experimental bits showed a 30% increase in usable hole over the conventional bits. These tests demonstrated a potential well cost reduction of 4 to 8%. Savings of 12% are considered possible with drilling procedures optimized for the experimental bits.

  20. Addition of the pirani condition to the Mathisson-Papapetrou equations in a Schwarzschild Field

    SciTech Connect

    Plyatsko, R.M.

    1986-01-01

    This paper obtains relations that allow one to distinguish a unique center of mass of a rotating test body as it moves in the equatorial plane of a Schwarzchild field. This center of mass can be thought of as the instantaneous analog of the classical center of mass.

  1. Matching of additive and polarizable force fields for multiscale condensed phase simulations

    PubMed Central

    Baker, Christopher M.; Best, Robert B.

    2013-01-01

    Inclusion of electronic polarization effects is one of the key aspects in which the accuracy of current biomolecular force fields may be improved. The principal drawback of such approaches is the computational cost, which typically ranges from 3 – 10 times that of the equivalent additive model, and may be greater for more sophisticated treatments of polarization or other many-body effects. Here, we present a multiscale approach which may be used to enhance the sampling in simulations with polarizable models, by using the additive model as a tool to explore configuration space. We use a method based on information theory to determine the charges for an additive model that has optimal overlap with the polarizable one, and we demonstrate the feasibility of enhancing sampling via a hybrid replica exchange scheme for several model systems. An additional advantage is that, in the process, we obtain a systematic method for deriving charges for an additive model that will be the natural complement to its polarizable parent. The additive charges are found by an effective coarse-graining of the polarizable force field, rather than by ad hoc procedures. PMID:23997691

  2. A test strategy for the assessment of additive attributed toxicity of tobacco products.

    PubMed

    Kienhuis, Anne S; Staal, Yvonne C M; Soeteman-Hernández, Lya G; van de Nobelen, Suzanne; Talhout, Reinskje

    2016-08-01

    The new EU Tobacco Product Directive (TPD) prohibits tobacco products containing additives that are toxic in unburnt form or that increase overall toxicity of the product. This paper proposes a strategy to assess additive attributed toxicity in the context of the TPD. Literature was searched on toxicity testing strategies for regulatory purposes from tobacco industry and governmental institutes. Although mainly traditional in vivo testing strategies have been applied to assess toxicity of unburnt additives and increases in overall toxicity of tobacco products due to additives, in vitro tests combined with toxicogenomics and validated using biomarkers of exposure and disease are most promising in this respect. As such, tests are needed that are sensitive enough to assess additive attributed toxicity above the overall toxicity of tobacco products, which can associate assay outcomes to human risk and exposure. In conclusion, new, sensitive in vitro assays are needed to conclude whether comparable testing allows for assessment of small changes in overall toxicity attributed to additives. A more pragmatic approach for implementation on a short-term is mandated lowering of toxic emission components. Combined with risk assessment, this approach allows assessment of effectiveness of harm reduction strategies, including banning or reducing of additives.

  3. Internal additive noise effects in stochastic resonance using organic field effect transistor

    NASA Astrophysics Data System (ADS)

    Suzuki, Yoshiharu; Matsubara, Kiyohiko; Asakawa, Naoki

    2016-08-01

    Stochastic resonance phenomenon was observed in organic field effect transistor using poly(3-hexylthiophene), which enhances performance of signal transmission with application of noise. The enhancement of correlation coefficient between the input and output signals was low, and the variation of correlation coefficient was not remarkable with respect to the intensity of external noise, which was due to the existence of internal additive noise following the nonlinear threshold response. In other words, internal additive noise plays a positive role on the capability of approximately constant signal transmission regardless of noise intensity, which can be said "homeostatic" behavior or "noise robustness" against external noise. Furthermore, internal additive noise causes emergence of the stochastic resonance effect even on the threshold unit without internal additive noise on which the correlation coefficient usually decreases monotonically.

  4. Acceptance test report for the 241-AN-107 caustic addition mixer pump data logger

    SciTech Connect

    Dowell, J.L.

    1996-04-05

    The Acceptance Test Procedure for the 241-AN-107 Caustic Addition Mixer Pump Data logger, WHC-SD-WM-ATP-149, was started on September 25, 1995, and completed November 13, 1995. K.G. Carothers of Tank Waste Remediation Engineering requested the test procedure and ICF Kaiser Control Systems Engineering group wrote the test procedure and executed it at the 305 building in 300 area and at the 241-AN Tank Farm in 200 East area. The purpose of this report is to document that the Caustic addition Mixer Pump Data logger, functioned as intended as installed at 241-AN-107 tank farm.

  5. Leach testing of in situ stabilization grouts containing additives to sequester contaminants

    SciTech Connect

    Serne, R.J.; Ames, L.L.; Martin, P.F.C.; LeGore, V.L.; Lindenmeier, C.W. ); Phillips, S.J. )

    1993-04-01

    This document discusses laboratory testing performed by Pacific Northwest Laboratory (PNL) for Westinghouse Hanford Company (WHC) of special grout formulations that incorporate specific sequestering agents to help improve the ability of the cement to resist contaminant leaching. To enhance the sequestering of contaminants we chose five additives to introduce (singly) to the control cement. The additives were Florida pebble phosphate, clinoptilolite (a natural zeolite), ferrous sulfide (a reductant), a mixed bed organic ion exchange resin and a proprietary anion-adsorbing mixed metal oxide. These additives were added one per test to the standard formulation and used to encapsulate a diluted high-salt alkaline liquid waste that is produced after various processes to remove uranium and plutonium from spent nuclear fuel. This report documents the testing of these additives.

  6. Field Lysimeter Test Facility: Second year (FY 1989) test results

    SciTech Connect

    Campbell, M.D.; Gee, G.W.; Kanyid, M.J.; Rockhold, M.L.

    1990-04-01

    The Record of Decision associated with the Hanford Defense Waste Environmental Impact Statement (53 FR 12449-53) commits to an evaluation of the use of protective barriers placed over near-surface wastes. The barrier must protect against wind and water erosion and limit plant and animal intrusion and infiltration of water. Successful conclusion of this program will yield the necessary protective barrier design for near-surface waste isolation. This report presents results from the second year of tests at the FLTF. The primary objective of testing protective barriers at the FLTF was to measure the water budgets within the various barriers and assess the effectiveness of their designs in limiting water intrusion into the zone beneath each barrier. Information obtained from these measurements is intended for use in refining barrier designs. Four elements of water budget were measured during the year: precipitation, evaporation, storage, and drainage. Run-off, which is a fifth element of a complete water budget, was made negligible by a lip on the lysimeters that protrudes 5 cm above the soil surface to prevent run-off. A secondary objective of testing protective barriers at the FLTF was to refine procedures and equipment to support data collection for verification of the computer model needed for long-term projections of barrier performance. 6 refs.

  7. Hydro-Balanced Stuffing Box field test

    SciTech Connect

    Giangiacomo, L.A.

    1999-05-28

    The Hydro-Balanced Stuffing Box is a seal assembly for polished rod pumping installations commonly used in oil and gas pumping well installations to contain produced well fluids. The improved stuffing box was developed and patented by Harold H. Palmour of The Palmour Group of Livingston, TX. The stuffing box is designed to reduce the incidence of seal leakage and to utilize an environmentally safe fluid, so that if there is any leakage, environmental damage is reduced or eliminated. The unit was tested on two wells at the Rocky Mountain Oilfield Testing Center. During the test period, the performance of the stuffing box was measured by monitoring the pressure on the tubing and the inner chamber with a Barton Two-pen recorder. The amount of safe fluid consumed, fluid leakage at the top of the stuffing box, pressure supplied from the nitrogen bottle, ambient temperature, and polish rod temperature was recorded. The stuffing box is capable of providing a better seal between well fluids an d the environment than conventional stuffing boxes. It allows the polished rod to operate cooler and with lubrication, extending the life of the packing elements, and reducing the amount of attention required to prevent leakage.

  8. Effect of Mg or Ag addition on the evaporation field of Al.

    PubMed

    Aruga, Yasuhiro; Nako, Hidenori; Tsuneishi, Hidemasa; Hasegawa, Yuki; Tao, Hiroaki; Ichihara, Chikara; Serizawa, Ai

    2013-09-01

    It is known that the distribution of the charge-states as well as the evaporation field shift to higher values as the specimen temperature is decreased at a constant rate of evaporation. This study has explored the effect of Mg or Ag addition on the evaporation field of Al in terms of the charge state distribution of the field evaporated Al ions. The fractional abundance of Al(2+) ions with respect to the total Al ions in Al-Mg alloy is lower than that in pure Al, whereas it shows higher level in the Al-Ag alloy at lower temperatures. The temperature dependence of the fractional abundance of Al(2+) ions has been also confirmed, suggesting that Al atoms in the Al-Mg alloy need lower evaporation field, while higher field is necessary to evaporate Al atoms in the Al-Ag alloy, compared with pure Al. This tendency is in agreement with that of the evaporation fields estimated theoretically by means of measurements of the work function and calculations of the binding energy of the pure Al, Al-Mg and Al-Ag alloys.

  9. Hybrid Residual Flexibility/Mass-Additive Method for Structural Dynamic Testing

    NASA Technical Reports Server (NTRS)

    Tinker, M. L.

    2003-01-01

    A large fixture was designed and constructed for modal vibration testing of International Space Station elements. This fixed-base test fixture, which weighs thousands of pounds and is anchored to a massive concrete floor, initially utilized spherical bearings and pendulum mechanisms to simulate Shuttle orbiter boundary constraints for launch of the hardware. Many difficulties were encountered during a checkout test of the common module prototype structure, mainly due to undesirable friction and excessive clearances in the test-article-to-fixture interface bearings. Measured mode shapes and frequencies were not representative of orbiter-constrained modes due to the friction and clearance effects in the bearings. As a result, a major redesign effort for the interface mechanisms was undertaken. The total cost of the fixture design, construction and checkout, and redesign was over $2 million. Because of the problems experienced with fixed-base testing, alternative free-suspension methods were studied, including the residual flexibility and mass-additive approaches. Free-suspension structural dynamics test methods utilize soft elastic bungee cords and overhead frame suspension systems that are less complex and much less expensive than fixed-base systems. The cost of free-suspension fixturing is on the order of tens of thousands of dollars as opposed to millions, for large fixed-base fixturing. In addition, free-suspension test configurations are portable, allowing modal tests to be done at sites without modal test facilities. For example, a mass-additive modal test of the ASTRO-1 Shuttle payload was done at the Kennedy Space Center launch site. In this Technical Memorandum, the mass-additive and residual flexibility test methods are described in detail. A discussion of a hybrid approach that combines the best characteristics of each method follows and is the focus of the study.

  10. Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

    NASA Technical Reports Server (NTRS)

    Zusack, Steven

    2016-01-01

    I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM

  11. CHARMM General Force Field (CGenFF): A force field for drug-like molecules compatible with the CHARMM all-atom additive biological force fields

    PubMed Central

    Vanommeslaeghe, K.; Hatcher, E.; Acharya, C.; Kundu, S.; Zhong, S.; Shim, J.; Darian, E.; Guvench, O.; Lopes, P.; Vorobyov, I.; MacKerell, A. D.

    2010-01-01

    The widely used CHARMM additive all-atom force field includes parameters for proteins, nucleic acids, lipids and carbohydrates. In the present paper an extension of the CHARMM force field to drug-like molecules is presented. The resulting CHARMM General Force Field (CGenFF) covers a wide range of chemical groups present in biomolecules and drug-like molecules, including a large number of heterocyclic scaffolds. The parametrization philosophy behind the force field focuses on quality at the expense of transferability, with the implementation concentrating on an extensible force field. Statistics related to the quality of the parametrization with a focus on experimental validation are presented. Additionally, the parametrization procedure, described fully in the present paper in the context of the model systems, pyrrolidine, and 3-phenoxymethylpyrrolidine will allow users to readily extend the force field to chemical groups that are not explicitly covered in the force field as well as add functional groups to and link together molecules already available in the force field. CGenFF thus makes it possible to perform “all-CHARMM” simulations on drug-target interactions thereby extending the utility of CHARMM force fields to medicinally relevant systems. PMID:19575467

  12. FSA field test report, 1980 - 1982

    NASA Technical Reports Server (NTRS)

    Maxwell, H. G.; Grimmett, C. A.; Repar, J.; Frickland, P. O.; Amy, J. A.

    1983-01-01

    Photovoltaic modules made of new and developing materials were tested in a continuing study of weatherability, compatibility, and corrosion protection. Over a two-year period, 365 two-cell submodules have been exposed for various intervals at three outdoor sites in Southern California or subjected to laboratory acceptance tests. Results to date show little loss of maximum power output, except in two types of modules. In the first of these, failure is due to cell fracture from the stresses that arise as water is regained from the surrounding air by a hardboard substrate, which shrank as it dried during its encapsulation in plastic film at 150 C in vacuo. In the second, the glass superstrate is sensitive to cracking, which also damages the cells electrostatically bonded to it; inadequate bonding of interconnects to the cells is also a problem in these modules. In a third type of module, a polyurethane pottant has begun to yellow, though as yet without significant effect on maximum power output.

  13. Test of QED at critical field strength

    SciTech Connect

    Bula, C.

    1997-01-01

    In a new experiment at the Final Focus Test Beam at SLAC, a low-emittance 46.6 GeV electron beam is brought into collisions with terawatt pulses of 1054 nm or 527 nm wavelength from a Nd:glass laser. Peak laser intensities of 10{sup 18} W/cm{sup 2} have been achieved corresponding to a value of 0.6 for the parameter {eta} = e{epsilon}/m{omega}{sub 0}c. In this case, an electron that crosses the center of the laser pulse has near-unit interaction probability. Results are presented for multiphoton Compton scattering in which an electron interacts with up to four laser photons, in agreement with theoretical calculations.

  14. Brahms Mobile Agents: Architecture and Field Tests

    NASA Technical Reports Server (NTRS)

    Clancey, William J.; Sierhuis, Maarten; Kaskiris, Charis; vanHoof, Ron

    2002-01-01

    We have developed a model-based, distributed architecture that integrates diverse components in a system designed for lunar and planetary surface operations: an astronaut's space suit, cameras, rover/All-Terrain Vehicle (ATV), robotic assistant, other personnel in a local habitat, and a remote mission support team (with time delay). Software processes, called agents, implemented in the Brahms language, run on multiple, mobile platforms. These mobile agents interpret and transform available data to help people and robotic systems coordinate their actions to make operations more safe and efficient. The Brahms-based mobile agent architecture (MAA) uses a novel combination of agent types so the software agents may understand and facilitate communications between people and between system components. A state-of-the-art spoken dialogue interface is integrated with Brahms models, supporting a speech-driven field observation record and rover command system (e.g., return here later and bring this back to the habitat ). This combination of agents, rover, and model-based spoken dialogue interface constitutes a personal assistant. An important aspect of the methodology involves first simulating the entire system in Brahms, then configuring the agents into a run-time system.

  15. Influence of Polarization on Carbohydrate Hydration: A Comparative Study Using Additive and Polarizable Force Fields.

    PubMed

    Pandey, Poonam; Mallajosyula, Sairam S

    2016-07-14

    Carbohydrates are known to closely modulate their surrounding solvent structures and influence solvation dynamics. Spectroscopic investigations studying far-IR regions (below 1000 cm(-1)) have observed spectral shifts in the libration band (around 600 cm(-1)) of water in the presence of monosaccharides and polysaccharides. In this paper, we use molecular dynamics simulations to gain atomistic insight into carbohydrate-water interactions and to specifically highlight the differences between additive (nonpolarizable) and polarizable simulations. A total of six monosaccharide systems, α and β anomers of glucose, galactose, and mannose, were studied using additive and polarizable Chemistry at HARvard Macromolecular Mechanics (CHARMM) carbohydrate force fields. Solvents were modeled using three additive water models TIP3P, TIP4P, and TIP5P in additive simulations and polarizable water model SWM4 in polarizable simulations. The presence of carbohydrate has a significant effect on the microscopic water structure, with the effects being pronounced for proximal water molecules. Notably, disruption of the tetrahedral arrangement of proximal water molecules was observed due to the formation of strong carbohydrate-water hydrogen bonds in both additive and polarizable simulations. However, the inclusion of polarization resulted in significant water-bridge occupancies, improved ordered water structures (tetrahedral order parameter), and longer carbohydrate-water H-bond correlations as compared to those for additive simulations. Additionally, polarizable simulations also allowed the calculation of power spectra from the dipole-dipole autocorrelation function, which corresponds to the IR spectra. From the power spectra, we could identify spectral signatures differentiating the proximal and bulk water structures, which could not be captured from additive simulations. PMID:27266974

  16. [An additional test in the identification of Enterobacteriaceae and some representatives of the genus Vibrio].

    PubMed

    Bril'man, Ia E

    1995-01-01

    An additional test: aerobic redox fermentation in semiliquid Hiss' medium with mannitol is recommended for the indication of Enterobacteriaceae, Vibrio, etc. The majority of mannite-fermenting enterobacteria change the color of the indicator in a thin upper layer of a column of semiliquid Hiss' medium in comparison with the bulk of medium after 20-24 h growth in it. Such changes of the indicator are never observed with Shigella, Salmonella, Vibrio bacteria of the studied strains, Yersinia, some cocci, etc., which may be considered as an additional differential diagnostic test at early stages of investigation with due consideration for other known signs. The aerobic redox test does not require additional quantities of nutrient media, reagents, or glassware.

  17. FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

    SciTech Connect

    Susan S. Sorini; John F. Schabron; Joseph F. Rovani, Jr.

    2002-09-30

    Western Research Institute (WRI) has developed a new commercial product ready for technology transfer, the Diesel Dog{reg_sign} Portable Soil Test Kit, for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to the technology by taking the method through the American Society for Testing and Materials (ASTM) approval and validation processes. The method is designated as ASTM Method D 5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In June 2001, the Diesel Dog technology won an American Chemical Society Regional Industrial Innovations Award. To gain field experience with the new technology, Diesel Dog kits have been used for a variety of site evaluation and cleanup activities. Information gained from these activities has led to improvements in hardware configurations and additional insight into correlating Diesel Dog results with results from laboratory methods. The Wyoming Department of Environmental Quality (DEQ) used Diesel Dog Soil Test Kits to guide cleanups at a variety of sites throughout the state. ENSR, of Acton, Massachusetts, used a Diesel Dog Portable Soil Test Kit to evaluate sites in the Virgin Islands and Georgia. ChemTrack and the U.S. Army Corps of Engineers successfully used a test kit to guide excavation at an abandoned FAA fuel-contaminated site near Fairbanks, Alaska. Barenco, Inc. is using a Diesel Dog Portable Soil Test Kit for site evaluations in Canada. A small spill of diesel fuel was cleaned up in Laramie, Wyoming using a Diesel

  18. Instructions for additional qualitative scoring of the initial-letter Word-association Test.

    PubMed

    Zivković, M

    1994-04-01

    An additional scoring method is based on grouping test-words according to whether the same sign is given by subjects to the test-words. In this way five test-word categories are formed, Eros (test-words with double plus signs), demi-Eros (single plus sign), demi-Thanatos (single minus), Thanatos (double minus), and Deviant (+/- and theta signs). The next step in scoring is to count the number of test-words in a given scoring category whose meanings do not conform. The greater the discrepancy between the test-word category and its meaning, the less well adapted is the subject. Several illustrative protocols are discussed. PMID:8022674

  19. Test ion transport in a collisional, field-reversed configuration

    NASA Astrophysics Data System (ADS)

    Roche, T.; McWilliams, R.; Heidbrink, W. W.; Bolte, N.; Garate, E. P.; Morehouse, M.; Slepchenkov, M.; Wessel, F.

    2014-08-01

    Diffusion of test-ions in a flux-coil generated, collisional, field-reversed configuration is measured via time-resolved tomographic reconstruction of Ar+ optical emission in the predominantly nitrogen plasma. Azimuthal test ion diffusion across magnetic field lines is found to be classical during the stable period of the discharge. Test ion radial confinement is enhanced by a radial electric field, reducing the observed outward radial transport rate below predictions based solely on classical cross-field diffusion rates. Test ion diffusion is ˜500 m2 s-1 during the stable period of the discharge. The electric field inferred from plasma potential measurements and from equilibrium calculations is consistent with the observed reduction in argon transport.

  20. Testing for Links Between Geomagnetic Field Variability and Climate Change

    NASA Astrophysics Data System (ADS)

    Wetter, L.; Acton, G.; Hill, T.

    2006-12-01

    Although orbital forcing controls much of long-term climate change and increases in greenhouse gases are thought to be driving recent global warming, other factors may also play a significant role. Recent studies have hypothesized various forms of links between climate change and solar irradiance, solar activity, and cosmic ray flux. Because changes in geomagnetic field strength affect the cosmic ray flux, it is possible that changes in the geomagnetic field contribute to long- and short-term climate change. Alternatively, it has been hypothesized that geomagnetic field variability is influenced by climate change or solar activity. We test such claims through a paleomagnetic and stable isotope study of Ocean Drilling Program (ODP) sediment cores from the Blake Outer Ridge (BOR), western North Atlantic Ocean. The goal of the study is to create a continuous, high-resolution record of geomagnetic field variability with an accurate, astronomically tuned chronology. Sediment cored on the BOR in four holes at Site 1061 during ODP Leg 172 is being used for this investigation. The high sedimentation rate, averaging 22 cm/k.y. over the Brunhes, and the exceptional paleomagnetic properties of the area make Site 1061 an excellent candidate to test for links between short- term geomagnetic events and climate. The paleomagnetic record, originally constructed mainly from continuous split-core measurements, is being refined and rock magnetic analyses are being conducted on U- channel samples that span the Brunhes. We have also refined the between-hole correlation and constructed a more detailed composite stratigraphic section for Site 1061 in order to improve the continuity and relative chronology of the record and to confirm the existence of distinct geomagnetic excursions and other short-term events in multiple drill holes. Additionally, planktonic forams are being measured for δ18 O variations across, and extending to one meter beyond each observed excursion, allowing for

  1. Designing an Online In-House Major Field Learning Test

    ERIC Educational Resources Information Center

    Gilda, Agacer; Christofi, Andreas; Moliver, Donald

    2014-01-01

    Our paper provides some critical attributes of an online homegrown assessment test, which we labelled Major Field Learning Test (MFLT). These attributes are also valid for departmental tests, directly connected to coursework which makes up the MFLT. The paper provides helpful recommendations for online assessment of learning as well as retention…

  2. Field tests of transgenic barley lines in North Dakota

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Testing transgenic barley lines for FHB in the greenhouse does not necessarily give the same results as field tests. The objective of this project was to test 18 transgenic lines in replicated trials in an inoculated FHB nursery. Several programs have developed barley lines expressing anti-fungal a...

  3. The force-field derivation and application of explosive/additive interfaces

    NASA Astrophysics Data System (ADS)

    Long, Yao; Chen, Jun

    2016-10-01

    The inter-molecular force-field across RDX/(paraffin, fluoropolymer) interfaces are derived from first-principles calculated energies under the GGA+vdW functional. Based on the force-field, the polycrystal structures of mixture explosives are obtained, and a set of thermodynamic properties are calculated, including the elastic constants, thermal expansion coefficient, heat capacity, isothermal curve and the Hugoniot curve. The results are in good agreement with the available experiments, and provide a reasonable prediction about the properties of plastic bonded explosives. We find that the thermal expansion coefficient of a multi-component explosive is not only determined by the properties of the components, but is also affected by the thermal stress at the explosive/additive interfaces.

  4. Probe Station and Near-Field Scanner for Testing Antennas

    NASA Technical Reports Server (NTRS)

    Zaman, Afroz; Lee, Richard Q.; Darby, William G.; Barr, Philip J.; Miranda, Felix A.; Lambert, Kevin

    2006-01-01

    A facility that includes a probe station and a scanning open-ended waveguide probe for measuring near electromagnetic fields has been added to Glenn Research Center's suite of antenna-testing facilities, at a small fraction of the cost of the other facilities. This facility is designed specifically for nondestructive characterization of the radiation patterns of miniaturized microwave antennas fabricated on semiconductor and dielectric wafer substrates, including active antennas that are difficult to test in traditional antenna-testing ranges because of fragility, smallness, or severity of DC-bias or test-fixture requirements. By virtue of the simple fact that a greater fraction of radiated power can be captured in a near-field measurement than in a conventional far-field measurement, this near-field facility is convenient for testing miniaturized antennas with low gains.

  5. Multiplicative noise effects on electroconvection in controlling additive noise by a magnetic field

    NASA Astrophysics Data System (ADS)

    Huh, Jong-Hoon

    2015-12-01

    We report multiplicative noise-induced threshold shift of electroconvection (EC) in the presence of a magnetic field H . Controlling the thermal fluctuation (i.e., additive noise) of the rodlike molecules of nematic liquid crystals by H , the EC threshold is examined at various noise levels [characterized by their intensity and cutoff frequency (fc) ]. For a sufficiently strong H (i.e., ignorable additive noise), a modified noise sensitivity characterizing the shift problem is in good agreement with experimental results for colored as well as white noise (fc→∞ ) ; until now, there was a large deviation for (sufficiently) colored noises. The present study shows that H provides us with ideal conditions for studying the corresponding Carr-Helfrich theory considering pure multiplicative noise.

  6. Testing for departures from additivity in mixtures of perfluoroalkyl acids (PFAAs)

    EPA Science Inventory

    This study is a follow-up to a paper by Carr, et al. that determined a design structure to optimally test for departures from additivity in a fixed ratio mixture of four perfluoroalkyl acids (PFAAs) using an in vitro transiently-transfected COS- 1 PPARa reporter model with an NHA...

  7. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  8. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  9. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  10. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  11. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  12. Prototype Engineered Barrier System Field Tests; Progress report

    SciTech Connect

    Ramirez, A.L.; Beatty, J.; Buscheck, T.A.; Carlson, R.; Daily, W.; LaTorre, V.R.; Lee, K.; Lin, Wunan; Mao, Nai-hsien; Nitao, J.J.; Towse, D.; Ueng, Tzou-Shin; Watwood, D.; Wilder, D.

    1989-07-26

    This paper presents selected preliminary results obtained during the first 54 days of the Prototype Engineered Barrier System Field Tests (PEBSFT) that are being performed in G-Tunnel within the Nevada Test Site. The test described is a precursor to the Engineered Barrier Systems Field Tests (EBSFT). The EBSFT will consist of in situ tests of the geohydrologic and geochemical environment in the near field (within a few meters) of heaters emplaced in welded tuff to simulate the thermal effects of waste packages. The PEBSFTs are being conducted to evaluate the applicability of measurement techniques, numerical models, and procedures for future investigations that will be conducted in the Exploratory Shaft Facilities of the Yucca Mountain Project (YMP). The paper discusses the evolution of hydrothermal behavior during the prototype test, including rock temperatures, changes in rock moisture content, air permeability of fractures, gas pressures, and rock mass gas-phase humidity. 10 refs., 12 figs.

  13. Field-based physiological testing of wheelchair athletes.

    PubMed

    Goosey-Tolfrey, Victoria L; Leicht, Christof A

    2013-02-01

    The volume of literature on field-based physiological testing of wheelchair sports, such as basketball, rugby and tennis, is considerably smaller when compared with that available for individuals and team athletes in able-bodied (AB) sports. In analogy to the AB literature, it is recognized that performance in wheelchair sports not only relies on fitness, but also sport-specific skills, experience and technical proficiency. However, in contrast to AB sports, two major components contribute towards 'wheeled sports' performance, which are the athlete and the wheelchair. It is the interaction of these two that enable wheelchair propulsion and the sporting movements required within a given sport. Like any other athlete, participants of wheelchair sports are looking for efficient ways to train and/or analyse their technique and fitness to improve their performance. Consequently, laboratory and/or field-based physiological monitoring tools used at regular intervals at key time points throughout the year must be considered to help with training evaluation. The present review examines methods available in the literature to assess wheelchair sports fitness in a field-based environment, with special attention on outcome variables, validity and reliability issues, and non-physiological influences on performance. It also lays out the context of field-based testing by providing details about the Paralympic court sports and the impacts of a disability on sporting performance. Due to the limited availability of specialized equipment for testing wheelchair-dependent participants in the laboratory, the adoption of field-based testing has become the preferred option by team coaches of wheelchair athletes. An obvious advantage of field-based testing is that large groups of athletes can be tested in less time. Furthermore, athletes are tested in their natural environment (using their normal sports wheelchair set-up and floor surface), potentially making the results of such testing

  14. Field-based physiological testing of wheelchair athletes.

    PubMed

    Goosey-Tolfrey, Victoria L; Leicht, Christof A

    2013-02-01

    The volume of literature on field-based physiological testing of wheelchair sports, such as basketball, rugby and tennis, is considerably smaller when compared with that available for individuals and team athletes in able-bodied (AB) sports. In analogy to the AB literature, it is recognized that performance in wheelchair sports not only relies on fitness, but also sport-specific skills, experience and technical proficiency. However, in contrast to AB sports, two major components contribute towards 'wheeled sports' performance, which are the athlete and the wheelchair. It is the interaction of these two that enable wheelchair propulsion and the sporting movements required within a given sport. Like any other athlete, participants of wheelchair sports are looking for efficient ways to train and/or analyse their technique and fitness to improve their performance. Consequently, laboratory and/or field-based physiological monitoring tools used at regular intervals at key time points throughout the year must be considered to help with training evaluation. The present review examines methods available in the literature to assess wheelchair sports fitness in a field-based environment, with special attention on outcome variables, validity and reliability issues, and non-physiological influences on performance. It also lays out the context of field-based testing by providing details about the Paralympic court sports and the impacts of a disability on sporting performance. Due to the limited availability of specialized equipment for testing wheelchair-dependent participants in the laboratory, the adoption of field-based testing has become the preferred option by team coaches of wheelchair athletes. An obvious advantage of field-based testing is that large groups of athletes can be tested in less time. Furthermore, athletes are tested in their natural environment (using their normal sports wheelchair set-up and floor surface), potentially making the results of such testing

  15. Metrology test object for dimensional verification in additive manufacturing of metals for biomedical applications.

    PubMed

    Teeter, Matthew G; Kopacz, Alexander J; Nikolov, Hristo N; Holdsworth, David W

    2015-01-01

    Additive manufacturing continues to increase in popularity and is being used in applications such as biomaterial ingrowth that requires sub-millimeter dimensional accuracy. The purpose of this study was to design a metrology test object for determining the capabilities of additive manufacturing systems to produce common objects, with a focus on those relevant to medical applications. The test object was designed with a variety of features of varying dimensions, including holes, cylinders, rectangles, gaps, and lattices. The object was built using selective laser melting, and the produced dimensions were compared to the target dimensions. Location of the test objects on the build plate did not affect dimensions. Features with dimensions less than 0.300 mm did not build or were overbuilt to a minimum of 0.300 mm. The mean difference between target and measured dimensions was less than 0.100 mm in all cases. The test object is applicable to multiple systems and materials, tests the effect of location on the build, uses a minimum of material, and can be measured with a variety of efficient metrology tools (including measuring microscopes and micro-CT). Investigators can use this test object to determine the limits of systems and adjust build parameters to achieve maximum accuracy.

  16. Metrology test object for dimensional verification in additive manufacturing of metals for biomedical applications.

    PubMed

    Teeter, Matthew G; Kopacz, Alexander J; Nikolov, Hristo N; Holdsworth, David W

    2015-01-01

    Additive manufacturing continues to increase in popularity and is being used in applications such as biomaterial ingrowth that requires sub-millimeter dimensional accuracy. The purpose of this study was to design a metrology test object for determining the capabilities of additive manufacturing systems to produce common objects, with a focus on those relevant to medical applications. The test object was designed with a variety of features of varying dimensions, including holes, cylinders, rectangles, gaps, and lattices. The object was built using selective laser melting, and the produced dimensions were compared to the target dimensions. Location of the test objects on the build plate did not affect dimensions. Features with dimensions less than 0.300 mm did not build or were overbuilt to a minimum of 0.300 mm. The mean difference between target and measured dimensions was less than 0.100 mm in all cases. The test object is applicable to multiple systems and materials, tests the effect of location on the build, uses a minimum of material, and can be measured with a variety of efficient metrology tools (including measuring microscopes and micro-CT). Investigators can use this test object to determine the limits of systems and adjust build parameters to achieve maximum accuracy. PMID:25542613

  17. Photovoltaic-Powered Vaccine Refrigerator: Freezer Systems Field Test Results

    NASA Technical Reports Server (NTRS)

    Ratajczak, A. F.

    1985-01-01

    A project to develop and field test photovoltaic-powered refrigerator/freezers suitable for vaccine storage was undertaken. Three refrigerator/freezers were qualified; one by Solar Power Corp. and two by Solvolt. Follow-on contracts were awarded for 19 field test systems and for 10 field test systems. A total of 29 systems were installed in 24 countries between October 1981 and October 1984. The project, systems descriptions, installation experiences, performance data for the 22 systems for which field test data was reported, an operational reliability summary, and recommendations relative to system designs and future use of such systems are explained. Performance data indicate that the systems are highly reliable and are capable of maintaining proper vaccine storage temperatures in a wide range of climatological and user environments.

  18. Photovoltaic-powered vaccine refrigerator: Freezer systems field test results

    NASA Astrophysics Data System (ADS)

    Ratajczak, A. F.

    1985-08-01

    A project to develop and field test photovoltaic-powered refrigerator/freezers suitable for vaccine storage was undertaken. Three refrigerator/freezers were qualified; one by Solar Power Corp. and two by Solvolt. Follow-on contracts were awarded for 19 field test systems and for 10 field test systems. A total of 29 systems were installed in 24 countries between October 1981 and October 1984. The project, systems descriptions, installation experiences, performance data for the 22 systems for which field test data was reported, an operational reliability summary, and recommendations relative to system designs and future use of such systems are explained. Performance data indicate that the systems are highly reliable and are capable of maintaining proper vaccine storage temperatures in a wide range of climatological and user environments.

  19. STIS Sparse Field CTE test-internal {Cycle 12}

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    2003-07-01

    CTE measurements are made using the "internal sparse field test", along the parallel axis. The "POS=" optional parameter, introduced during cycle 11, is used to provide off-center MSM positionings of some slits. All exposures are internals.

  20. STIS Sparse Field CTE test-internal {Cycle 11}

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    2002-07-01

    CTE measurements are made using the "internal sparse field test", along the parallel axis. The new "POS=" optional parameter is used to provide off-center MSM positionings of some slits. All exposures are internals.

  1. Field Testing Research at the NWTC (Fact Sheet)

    SciTech Connect

    Not Available

    2015-02-01

    The National Wind Technology Center (NWTC) at the National Renewable Laboratory (NREL) has extensive field testing capabilities that have been used in collaboration with the wind industry to accelerate wind technology development and deployment for more than 30 years.

  2. The Center-TRACON Automation System: Simulation and field testing

    NASA Technical Reports Server (NTRS)

    Denery, Dallas G.; Erzberger, Heinz

    1995-01-01

    A new concept for air traffic management in the terminal area, implemented as the Center-TRACON Automation System, has been under development at NASA Ames in a cooperative program with the FAA since 1991. The development has been strongly influenced by concurrent simulation and field site evaluations. The role of simulation and field activities in the development process will be discussed. Results of recent simulation and field tests will be presented.

  3. Development of a specific anaerobic field test for aerobic gymnastics.

    PubMed

    Alves, Christiano Robles Rodrigues; Borelli, Marcello Tadeu Caetano; Paineli, Vitor de Salles; Azevedo, Rafael de Almeida; Borelli, Claudia Cristine Gomes; Lancha Junior, Antônio Herbert; Gualano, Bruno; Artioli, Guilherme Giannini

    2015-01-01

    The current investigation aimed to develop a valid specific field test to evaluate anaerobic physical performance in Aerobic Gymnastics athletes. We first designed the Specific Aerobic Gymnast Anaerobic Test (SAGAT), which included gymnastics-specific elements performed in maximal repeated sprint fashion, with a total duration of 80-90 s. In order to validate the SAGAT, three independent sub-studies were performed to evaluate the concurrent validity (Study I, n=8), the reliability (Study II, n=10) and the sensitivity (Study III, n=30) of the test in elite female athletes. In Study I, a positive correlation was shown between lower-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.69, CI: -0.94 to 0.03 and Peak power: p = 0.02, r = -0.72, CI: -0.95 to -0.04) and between upper-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.67, CI: -0.94 to 0.02 and Peak power: p = 0.03, r = -0.69, CI: -0.94 to 0.03). Additionally, plasma lactate was similarly increased in response to SAGAT (p = 0.002), lower-body Wingate Test (p = 0.021) and a simulated competition (p = 0.007). In Study II, no differences were found between the time to complete the SAGAT in repeated trials (p = 0.84; Cohen's d effect size = 0.09; ICC = 0.97, CI: 0.89 to 0.99; MDC95 = 0.12 s). Finally, in Study III the time to complete the SAGAT was significantly lower during the competition cycle when compared to the period before the preparatory cycle (p < 0.001), showing an improvement in SAGAT performance after a specific Aerobic Gymnastics training period. Taken together, these data have demonstrated that SAGAT is a specific, reliable and sensitive measurement of specific anaerobic performance in elite female Aerobic Gymnastics, presenting great potential to be largely applied in training settings. PMID:25876039

  4. Advanced Utility Mercury-Sorbent Field-Testing Program

    SciTech Connect

    Ronald Landreth

    2007-12-31

    This report summarizes the work conducted from September 1, 2003 through December 31, 2007 on the project entitled Advanced Utility Mercury-Sorbent Field-Testing Program. The project covers the testing at the Detroit Edison St. Clair Plant and the Duke Power Cliffside and Buck Stations. The St. Clair Plant used a blend of subbituminous and bituminous coal and controlled the particulate emissions by means of a cold-side ESP. The Duke Power Stations used bituminous coals and controlled their particulate emissions by means of hot-side ESPs. The testing at the Detroit Edison St. Clair Plant demonstrated that mercury sorbents could be used to achieve high mercury removal rates with low injection rates at facilities that burn subbituminous coal. A mercury removal rate of 94% was achieved at an injection rate of 3 lb/MMacf over the thirty day long-term test. Prior to this test, it was believed that the mercury in flue gas of this type would be the most difficult to capture. This is not the case. The testing at the two Duke Power Stations proved that carbon- based mercury sorbents can be used to control the mercury emissions from boilers with hot-side ESPs. It was known that plain PACs did not have any mercury capacity at elevated temperatures but that brominated B-PAC did. The mercury removal rate varies with the operation but it appears that mercury removal rates equal to or greater than 50% are achievable in facilities equipped with hot-side ESPs. As part of the program, both sorbent injection equipment and sorbent production equipment was acquired and operated. This equipment performed very well during this program. In addition, mercury instruments were acquired for this program. These instruments worked well in the flue gas at the St. Clair Plant but not as well in the flue gas at the Duke Power Stations. It is believed that the difference in the amount of oxidized mercury, more at Duke Power, was the difference in instrument performance. Much of the equipment was

  5. Development of a Specific Anaerobic Field Test for Aerobic Gymnastics

    PubMed Central

    Paineli, Vitor de Salles; Azevedo, Rafael de Almeida; Borelli, Claudia Cristine Gomes; Lancha Junior, Antônio Herbert; Gualano, Bruno; Artioli, Guilherme Giannini

    2015-01-01

    The current investigation aimed to develop a valid specific field test to evaluate anaerobic physical performance in Aerobic Gymnastics athletes. We first designed the Specific Aerobic Gymnast Anaerobic Test (SAGAT), which included gymnastics-specific elements performed in maximal repeated sprint fashion, with a total duration of 80-90 s. In order to validate the SAGAT, three independent sub-studies were performed to evaluate the concurrent validity (Study I, n=8), the reliability (Study II, n=10) and the sensitivity (Study III, n=30) of the test in elite female athletes. In Study I, a positive correlation was shown between lower-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.69, CI: -0.94 to 0.03 and Peak power: p = 0.02, r = -0.72, CI: -0.95 to -0.04) and between upper-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.67, CI: -0.94 to 0.02 and Peak power: p = 0.03, r = -0.69, CI: -0.94 to 0.03). Additionally, plasma lactate was similarly increased in response to SAGAT (p = 0.002), lower-body Wingate Test (p = 0.021) and a simulated competition (p = 0.007). In Study II, no differences were found between the time to complete the SAGAT in repeated trials (p = 0.84; Cohen’s d effect size = 0.09; ICC = 0.97, CI: 0.89 to 0.99; MDC95 = 0.12 s). Finally, in Study III the time to complete the SAGAT was significantly lower during the competition cycle when compared to the period before the preparatory cycle (p < 0.001), showing an improvement in SAGAT performance after a specific Aerobic Gymnastics training period. Taken together, these data have demonstrated that SAGAT is a specific, reliable and sensitive measurement of specific anaerobic performance in elite female Aerobic Gymnastics, presenting great potential to be largely applied in training settings. PMID:25876039

  6. Field Lysimeter Test Facility status report IV: FY 1993

    SciTech Connect

    Gee, G.W.; Felmy, D.G.; Ritter, J.C.; Campbell, M.D.; Downs, J.L.; Fayer, M.J.; Kirkham, R.R.; Link, S.O.

    1993-10-01

    At the U.S. Department of Energy`s Hanford Site near Richland, Washington, a unique facility, the Field Lysimeter Test Facility (FLTF) is used to measure drainage from and water storage in soil covers. Drainage has ranged from near zero amounts to more than 50% of the applied water, with the amount depending on vegetative cover and soil type. Drainage occurred from lysimeters with coarse soils and gravel covers, but did not occur from capillary barrier-type lysimeters (1.5 m silt loam soil over coarse sands and gravels) except under the most extreme condition tested. For capillary barriers that were irrigated and kept vegetation-free (bare surface), no drainage occurred in 5 of the past 6 years. However, this past year (1992--1993) a record snowfall of 1,425 mm occurred and water storage in the irrigated, bare-surfaced capillary barriers exceeded 500 mm resulting in drainage of more than 30 mm from these barriers. In contrast, capillary barriers, covered with native vegetation (i.e., shrubs and grasses) did not drain under any climatic condition (with or without irrigation). In FY 1994, the FLTF treatments will be increased from 11 to 17 with the addition of materials that will simulate portions of a prototype barrier planned for construction in 1994 at the Hanford Site. The 17 FLTF treatments are designed to test the expected range of surface soil, vegetation, and climatic conditions encountered at the Hanford Site and will assist in evaluating final surface barrier designs for a waste disposal facility.

  7. Results of field tests of a transportable calorimeter assay system

    SciTech Connect

    Rakel, D.A.; Lemming, J.F.; Rodenburg, W.W.; Duff, M.F.; Jarvis, J.Y.

    1981-01-01

    A transportable calorimetric assay system, developed for use by US Department of Energy inspectors, is described. The results of field tests at three DOE sites are presented. The samples measured in these tests represent a variety of forms (ash, oxide, metal buttons), isotopic composition, and total plutonium content.

  8. Differential Gender Performance on the Major Field Test-Business

    ERIC Educational Resources Information Center

    Bielinska-Kwapisz, Agnieszka; Brown, F. William

    2013-01-01

    The Major Field Test in Business (MFT-B), a standardized assessment test of business knowledge among undergraduate business seniors, is widely used to measure student achievement. Many previous studies analyzing scores on the MFT-B report gender differences on the exam even after controlling for student's aptitude, general intellectual…

  9. Documenting and Explaining Major Field Test Results among Undergraduate Students

    ERIC Educational Resources Information Center

    Contreras, Salvador; Badua, Frank; Chen, Jiun Shiu; Adrian, Mitchell

    2011-01-01

    The authors investigated the results of the Educational Testing Service Major Field Test (ETS-MFT) administered to business majors at a U.S. state university. Longitudinal trends and cross-sectional differences are documented, including significant performance differences among students of different majors. Findings suggest that a cohort affect…

  10. Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

    NASA Technical Reports Server (NTRS)

    Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

    2012-01-01

    Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility

  11. Magnetic field exposure in a nondestructive testing operation.

    PubMed

    Lippert, Julia F; Lacey, Steven E; Kennedy, Kathleen J; Esmen, Nurtan A; Buchanich, Jeanine M; Marsh, Gary M

    2007-01-01

    Nondestructive testing is any technique used to inspect the integrity of a manufactured item without diminishing its future usefulness. Magnetic particle inspection is one type of nondestructive testing that uses electromagnetism in the inspection procedure, thus potentially exposing the operator to magnetic fields. During magnetic particle inspection, investigators took peak magnetic field measurements of 8 turbine engine shafts at a turbine engine overhaul and repair center. They recorded 95 peak magnetic field measurements, ranging from < 0.1 to 29.27 mT. The exposure values measured were among the highest reported in the occupational setting. Further work is needed to characterize magnetic field exposures in magnetic particle inspection operations--in particular, by differentiating magnetic field magnitude by current frequency--and to understand exposure as it relates to different types of magnetic particle inspection devices.

  12. Optimization of the CHARMM additive force field for DNA: Improved treatment of the BI/BII conformational equilibrium.

    PubMed

    Hart, Katarina; Foloppe, Nicolas; Baker, Christopher M; Denning, Elizabeth J; Nilsson, Lennart; Mackerell, Alexander D

    2012-01-10

    The B-form of DNA can populate two different backbone conformations: BI and BII, defined by the difference between the torsion angles ε and ζ (BI = ε-ζ < 0 and BII = ε-ζ > 0). BI is the most populated state, but the population of the BII state, which is sequence dependent, is significant and accumulating evidence shows that BII affects the overall structure of DNA, and thus influences protein-DNA recognition. This work presents a reparametrization of the CHARMM27 additive nucleic acid force field to increase the sampling of the BII form in MD simulations of DNA. In addition, minor modifications of sugar puckering were introduced to facilitate sampling of the A form of DNA under the appropriate environmental conditions. Parameter optimization was guided by quantum mechanical data on model compounds, followed by calculations on several DNA duplexes in the condensed phase. The selected optimized parameters were then validated against a number of DNA duplexes, with the most extensive tests performed on the EcoRI dodecamer, including comparative calculations using the Amber Parm99bsc0 force field. The new CHARMM model better reproduces experimentally observed sampling of the BII conformation, including sampling as a function of sequence. In addition, the model reproduces the A form of the 1ZF1 duplex in 75 % ethanol, and yields a stable Z-DNA conformation of duplex (GTACGTAC) in its crystal environment. The resulting model, in combination with a recent reoptimization of the CHARMM27 force field for RNA, will be referred to as CHARMM36.

  13. Automated particulate sampler field test model operations guide

    SciTech Connect

    Bowyer, S.M.; Miley, H.S.

    1996-10-01

    The Automated Particulate Sampler Field Test Model Operations Guide is a collection of documents which provides a complete picture of the Automated Particulate Sampler (APS) and the Field Test in which it was evaluated. The Pacific Northwest National Laboratory (PNNL) Automated Particulate Sampler was developed for the purpose of radionuclide particulate monitoring for use under the Comprehensive Test Ban Treaty (CTBT). Its design was directed by anticipated requirements of small size, low power consumption, low noise level, fully automatic operation, and most predominantly the sensitivity requirements of the Conference on Disarmament Working Paper 224 (CDWP224). This guide is intended to serve as both a reference document for the APS and to provide detailed instructions on how to operate the sampler. This document provides a complete description of the APS Field Test Model and all the activity related to its evaluation and progression.

  14. Analytical modeling of the acoustic field during a direct field acoustic test.

    SciTech Connect

    Stasiunas, Eric Carl; Rouse, Jerry W.; Mesh, Mikhail

    2010-12-01

    The acoustic field generated during a Direct Field Acoustic Test (DFAT) has been analytically modeled in two space dimensions using a properly phased distribution of propagating plane waves. Both the pure-tone and broadband acoustic field were qualitatively and quantitatively compared to a diffuse acoustic field. The modeling indicates significant non-uniformity of sound pressure level for an empty (no test article) DFAT, specifically a center peak and concentric maxima/minima rings. This spatial variation is due to the equivalent phase among all propagating plane waves at each frequency. The excitation of a simply supported slender beam immersed within the acoustic fields was also analytically modeled. Results indicate that mid-span response is dependent upon location and orientation of the beam relative to the center of the DFAT acoustic field. For a diffuse acoustic field, due to its spatial uniformity, mid-span response sensitivity to location and orientation is nonexistent.

  15. Geomechanical Considerations for the Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Park, B. Y.

    2015-12-01

    Deep borehole disposal of high-level radioactive waste is under consideration as a potential alternative to shallower mined repositories. The disposal concept consists of drilling a borehole into crystalline basement rocks to a depth of 5 km, emplacement of canisters containing solid waste in the lower 2 km, and plugging and sealing the upper 3 km of the borehole. Crystalline rocks such as granites are particularly attractive for borehole emplacement because of their low permeability and porosity at depth, and high mechanical strength to resist borehole deformation. In addition, high overburden pressures contribute to sealing of some of the fractures that provide transport pathways. We present geomechanical considerations during construction (e.g., borehole breakouts, disturbed rock zone development, and creep closure), relevant to both the smaller-diameter characterization borehole (8.5") and the larger-diameter field test borehole (17"). Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  16. Continuous field measurement of N2O isotopologues using FTIR spectroscopy following 15N addition

    NASA Astrophysics Data System (ADS)

    Phillips, R. L.; Griffith, D. W.; Dijkstra, F. A.; Lugg, G.; Lawrie, R.; Macdonald, B.

    2012-12-01

    Anthropogenic additions of fertilizer nitrogen (N) have significantly increased the mole fraction of nitrous oxide (N2O) in the troposphere. Tracking the fate of fertilizer N and its transformation to N2O is important to advance knowledge of greenhouse gas emissions from soils. Transport and transformations are frequently studied using 15N labeling experiments, but instruments capable of continuous measurements of 15N-N2O at the surface of soil have only recently come to the fore. Our primary aim was to quantify emissions of N2O and the fraction of 15N emitted as N2O from an agricultural soil following 15N addition using a mobile Fourier Transform Infrared (FTIR) spectrometer. We set up a short-term field experiment on a coastal floodplain site near Nowra, New South Wales. We deployed an automated chamber system connected to a multi-pass cell (optical pathlength 24 m) and low resolution FTIR spectrometer to measure fluxes of all N2O isotopologues collected from five 0.25 m2 chambers every three hours. We measured N2O fluxes pre and post-application of 15N-labeled substrate as potassium nitrate (KNO3) or urea [CO(NH2)2] to the soil surface. Root mean square uncertainties for all isotopologue measurements were less than 0.3 nmol mol-1 for 1 minute average concentration measurements, and minimum detectable fluxes for each isotopologue were <0.1 ng N m-2 s-1. Emissions of all N2O isotopologues were evident immediately following 15N addition. Emissions of 14N15NO, 15N14NO and 15N15NO isotopologues subsided within 10 d, but 14N14NO fluxes were evident over the entire experiment. The figure provides an overview of the emissions. Cumulative 15N-N2O fluxes (sum of the three 15N isotopologues) per chamber for the 14 days following 15N addition ranged from 1.5 to 10.3 mg 15N-N2O m-2. The chambers were destructively sampled after 2 weeks and 15N analyzed in soil and plant material using isotope ratio mass spectrometry. Approximately 1% (range 0.7 - 1.9%) of the total amount of

  17. DOE Field Operations Program EV and HEV Testing

    SciTech Connect

    Francfort, James Edward; Slezak, L. A.

    2001-10-01

    The United States Department of Energy’s (DOE) Field Operations Program tests advanced technology vehicles (ATVs) and disseminates the testing results to provide fleet managers and other potential ATV users with accurate and unbiased information on vehicle performance. The ATVs (including electric, hybrid, and other alternative fuel vehicles) are tested using one or more methods - Baseline Performance Testing (EVAmerica and Pomona Loop), Accelerated Reliability Testing, and Fleet Testing. The Program (http://ev.inel.gov/sop) and its nine industry testing partners have tested over 30 full-size electric vehicle (EV) models and they have accumulated over 4 million miles of EV testing experience since 1994. In conjunction with several original equipment manufacturers, the Program has developed testing procedures for the new classes of hybrid, urban, and neighborhood EVs. The testing of these vehicles started during 2001. The EVS 18 presentation will include (1) EV and hybrid electric vehicle (HEV) test results, (2) operating experience with and performance trends of various EV and HEV models, and (3) experience with operating hydrogen-fueled vehicles. Data presented for EVs will include vehicle efficiency (km/kWh), average distance driven per charge, and range testing results. The HEV data will include operating considerations, fuel use rates, and range testing results.

  18. Automated microbial metabolism laboratory. [design of advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into test chambers

    NASA Technical Reports Server (NTRS)

    1974-01-01

    The design and rationale of an advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into each of four test chambers are outlined. The feasibility for multiple addition tests was established and various details of the methodology were studied. The four chamber battery of tests include: (1) determination of the effect of various atmospheric gases and selection of that gas which produces an optimum response; (2) determination of the effect of incubation temperature and selection of the optimum temperature for performing Martian biochemical tests; (3) sterile soil is dosed with a battery of C-14 labeled substrates and subjected to experimental temperature range; and (4) determination of the possible inhibitory effects of water on Martian organisms is performed initially by dosing with 0.01 ml and 0.5 ml of medium, respectively. A series of specifically labeled substrates are then added to obtain patterns in metabolic 14CO2 (C-14)O2 evolution.

  19. Laboratory or field tests for evaluating firefighters' work capacity?

    PubMed

    Lindberg, Ann-Sofie; Oksa, Juha; Malm, Christer

    2014-01-01

    Muscle strength is important for firefighters work capacity. Laboratory tests used for measurements of muscle strength, however, are complicated, expensive and time consuming. The aims of the present study were to investigate correlations between physical capacity within commonly occurring and physically demanding firefighting work tasks and both laboratory and field tests in full time (N = 8) and part-time (N = 10) male firefighters and civilian men (N = 8) and women (N = 12), and also to give recommendations as to which field tests might be useful for evaluating firefighters' physical work capacity. Laboratory tests of isokinetic maximal (IM) and endurance (IE) muscle power and dynamic balance, field tests including maximal and endurance muscle performance, and simulated firefighting work tasks were performed. Correlations with work capacity were analyzed with Spearman's rank correlation coefficient (rs). The highest significant (p<0.01) correlations with laboratory and field tests were for Cutting: IE trunk extension (rs = 0.72) and maximal hand grip strength (rs = 0.67), for Stairs: IE shoulder flexion (rs = -0.81) and barbell shoulder press (rs = -0.77), for Pulling: IE shoulder extension (rs = -0.82) and bench press (rs = -0.85), for Demolition: IE knee extension (rs = 0.75) and bench press (rs = 0.83), for Rescue: IE shoulder flexion (rs = -0.83) and bench press (rs = -0.82), and for the Terrain work task: IE trunk flexion (rs = -0.58) and upright barbell row (rs = -0.70). In conclusion, field tests may be used instead of laboratory tests. Maximal hand grip strength, bench press, chin ups, dips, upright barbell row, standing broad jump, and barbell shoulder press were strongly correlated (rs≥0.7) with work capacity and are therefore recommended for evaluating firefighters work capacity. PMID:24614596

  20. Antarctic field tests of SARSAT personal locater beacons

    NASA Technical Reports Server (NTRS)

    Bindschadler, Robert

    1987-01-01

    Field tests of SARSAT personal locater beacons were conducted in the Antarctic to assess the viability of using these beacons to increase the safety of Antarctic field parties. Data were collected on the extent to which dry or wet snow, melting conditions, crevasse walls and snow bridges affected the ability of the SARSAT satellite to calculate an accurate position of the beacon. Average response time between beacon turn on and alert reception in McMurdo was between 4 and 5 hours for these tests. It is concluded that the SARSAT system is viable for Antarctic operations and it is recommended that it be implemented for future field operations. Because of obstruction of line-of-sight between beacon and satellite degrades the accuracy of the location calculation (particularly in wet snow), it is further recommended that field parties have sufficient numbers of beacons to insure that in an emergency, one will be able to operate from the surface.

  1. Field testing of fugitive dust control techniques at a uranium mill tailings pile - 1982 Field Test, Gas Hills, Wyoming.

    SciTech Connect

    Elmore, M.R.; Hartley, J.N.

    1983-12-01

    A field test was conducted on a uranium tailings pile to evaluate the effectiveness of 15 chemical stabilizers for control of fugitive dust from uranium mill tailings. A tailings pile at the Federal American Partners (FAP) Uranium Mill, Gas Hills, Wyoming, was used for the field test. Preliminary laboratory tests using a wing tunnel were conducted to select the more promising stabilizers for field testing. Fourteen of the chemical stabilizers were applied with a field spray system pulled behind a tractor; one--Hydro Mulch--was applied with a hydroseeder. A portable weather station and data logger were installed to record the weather conditions at the test site. After 1 year of monitoring (including three site visits), all of the stabilizers have degraded to some degree; but those applied at the manufacturers' recommended rate are still somewhat effective in reducing fugitive emissions. The following synthetic polymer emulsions appear to be the more effective stabilizers: Wallpol 40-133 from Reichold Chemicals, SP-400 from Johnson and March Corporation, and CPB-12 from Wen Don Corporation. Installed costs for the test plots ranged from $8400 to $11,300/ha; this range results from differences in stabilizer costs. Large-scale stabilization costs of the test materials are expected to range from $680 to $3600/ha based on FAP experience. Evaluation of the chemical stabilizers will continue for approximately 1 year. 2 references, 33 figures, 22 tables.

  2. Vadose zone transport field study: Detailed test plan for simulated leak tests

    SciTech Connect

    AL Ward; GW Gee

    2000-06-23

    : identify mechanisms controlling transport processes in soils typical of the hydrogeologic conditions of Hanford's waste disposal sites; reduce uncertainty in conceptual models; develop a detailed and accurate database of hydraulic and transport parameters for validation of three-dimensional numerical models; identify and evaluate advanced, cost-effective characterization methods with the potential to assess changing conditions in the vadose zone, particularly as surrogates of currently undetectable high-risk contaminants. This plan provides details for conducting field tests during FY 2000 to accomplish these objectives. Details of additional testing during FY 2001 and FY 2002 will be developed as part of the work planning process implemented by the Integration Project.

  3. Positive contrast in the rat: a test of the additivity theory.

    PubMed

    Nallan, G B; McCoy, D F

    1979-09-01

    Rats were trained to lever press for food on a multiple variable-interval variable-interval schedule, then shifted to a multiple variable-interval extinction schedule. For six subjects (group L), schedule components were signalled by the presence or absence of a flashing light emitted from an alternate, "signal" lever. For four subjects (group T), schedule components were signalled by two distinct auditory tones. Contrary to the predictions of an additivity theory based on the summation of response classes, contacts on the signal lever did not increase after the schedule shift in group L. However, nine of the ten subjects in the study demonstrated positive contrast effects on the operant lever. In a subsequent test for stimulus control, enhancement and suppression by the discriminative stimuli were found in these same nine subjects. An additivity theory based on the summation of excitatory processes, rather than response classes, appears to account for these data.

  4. Compositions, Functions, and Testing of Friction Brake Materials and Their Additives

    SciTech Connect

    Blau, PJ

    2001-10-22

    The purpose of this report is to present a survey of commercial brake materials and additives, and to indicate their typical properties and functions, especially as regards their use in heavy trucks. Most truck pad and shoe materials described here were designed to wear against cast iron. Brake material test methods are also briefly described. This report does not address issues associated with the fabrication and manufacturing of brake materials. Since there are literally thousands of brake material additives, and their combinations are nearly limitless, it is impractical to list them all here. Rather, an attempt has been made to capture the primary constituents and their functions. An Appendix contains thermo-physical properties of some current and potential brake materials.

  5. The use of the rapid osmotic fragility test as an additional test to diagnose canine immune-mediated haemolytic anaemia

    PubMed Central

    2013-01-01

    practice. Although, the ROFT cannot replace other diagnostic tests, it may be a valuable additional tool to diagnose canine IMHA. PMID:24160183

  6. Applicability of slug interference tests for hydraulic characterization of unconfined aquifers. 2: Field test examples

    SciTech Connect

    Spane, F.A. Jr.; Thorne, P.D.; Swanson, L.C.

    1996-09-01

    Slug interference testing may be particularly useful for characterizing hydraulic properties of aquifer sites where disposal of contaminated ground water makes pumping tests undesirable. The design, performance, and analysis of slug interference tests for two field test examples are presented. Results were compared with standard constant-rate pumping tests. The comparison indicates that slug interference tests provide estimates comparable to those obtained from short duration pumping tests for the determination of transmissivity, storativity, and vertical anisotropy. The close agreement in hydraulic property values obtained using the two test methods suggests that slug interference testing, under favorable test conditions (for example, observation well distances {le}30 m), can provide representative aquifer characterization results. The quality and extent of test data obtained also indicate the potential use of slug interference testing for three-dimensional hydrologic characterization investigations, when conducted using multilevel monitoring facilities.

  7. Application and testing of additive manufacturing for mirrors and precision structures

    NASA Astrophysics Data System (ADS)

    Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

    2015-09-01

    Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

  8. Immunogenicity of foods and food additives--in vivo testing of gums arabic, karaya and tragacanth.

    PubMed

    Strobel, S; Ferguson, A; Anderson, D M

    1982-12-01

    An inexpensive animal model is described, for investigation of the immunogenicity of substances such as food additives. Inbred mice were immunised with antigen emulsified in complete Freund's adjuvant, and specific cell-mediated immunity subsequently measured by a footpad swelling test. This method has been applied in an investigation of the immunogenicity of the exudate gums, gum arabic, gum karaya and gum tragacanth. These substances are capable of eliciting an immune response which is comparable to the specific immune responses elicited by a protein antigen, e.g. hens' egg ovalbumin. Purification of commercially available gum preparations led to a significant (P less than 0.005) reduction of the immune response under in vivo test conditions.

  9. Field joint protection system rain qualification test report

    NASA Technical Reports Server (NTRS)

    Cook, M.

    1989-01-01

    This report documents the procedures, performance, and results obtained from the Field Joint Protection System (FJPS) rain test. This test was performed to validate that the flight configuration FJPS prevents the accumulation of moisture in the redesigned solid rocket motor (RSRM) field joints when subjected to simulated prelaunch natural rain environments. The FJPS test article was exposed to rain simulation for approximately 50 minutes. During the test, water entered through the open upper end of the systems tunnel and was funneled down between the tunnel and case. A sealant void at the moisture seal butt splice allowed this water to flow underneath the FJPS. The most likely cause of voids was improper bondline preparation, particularly on the moisture seal surface. In total, water penetrated underneath approximately 60 percent of the FJPS circumference. Because the test article was substantially different from flight configuration (no systems tunnel closeout), results of this test will not affect current flight motors. Due to the omission of systems tunnel covers and systems tunnel floor plate closeout, the test assembly was not representative of flight hardware and resulted in a gross overtest. It is therefore recommended that the test be declared void. It is also recommended that the test be repeated with a complete closeout of the systems tunnel, sealed systems tunnel ends, and improved adhesive bondline preparation.

  10. Field test of fiber optic ocean bottom seismograph

    NASA Astrophysics Data System (ADS)

    Zhang, Wentao; Wang, Zhaogang; Huang, Wenzhu; Li, Li; Liu, Wenyi; Luo, Yingbo; Li, Fang

    2016-05-01

    In this paper we report the field test of fiber optic ocean bottom seismograph (OOBS) which can be used in the active source seismic research. There are three fiber laser accelerometers (FLAs) and one fiber laser hydrophone (FLH), which is wavelength division multiplexed, in the OOBS. The interrogation system is put on shore and is connected with the OOBS with optical fiber cable. The field test of using an air gun is carried out under water with a depth of 30 m. The results show that the OOBS has similar performance as conventional electric OBS.

  11. Field test of microbend fiber sensor for hospital use

    NASA Astrophysics Data System (ADS)

    Chen, Zhihao; Lau, Doreen; Teo, Ju Teng; Ng, Soon Huat; Yang, Xiufeng; Kei, Pin Lin

    2014-05-01

    In this paper, we report a field test of a microbend fiber sensor for simultaneous measurement of breathing rate, breathing pattern, Ballistocardiogram and heart rate during magnetic resonance imaging (MRI). Comparative experiments conducted between our sensor and commercial physiologic device on a healthy male subject showed an accuracy of +/-2bpm for simultaneous measurement of both breathing rate and heart rate. Our preliminary field test on simultaneous measurement of breathing rate and heart rate in a clinical trial conducted on 11 healthy subjects in the 3.0 Tesla MRI environment showed very good agreement compared with measurements obtained from conventional MRcompatible devices.

  12. Development of a field test for upper-body power.

    PubMed

    Shim, A L; Bailey, M L; Westings, S H

    2001-05-01

    The purpose of this study was to develop a field test capable of measuring upper-body power through the use of a common weight-training apparatus, a Smith machine (SM), set up for bench press (BP) movement. A small, battery-operated digital timing device was designed and constructed to allow a precise calculation of power (in conjunction with measures of distance and force) for this specific movement, which involved an explosive press from the chest to a position just short of full arm extension. In pilot work, 1 repetition maximums (1RM) were determined on the SM BP for 3 male subjects, and by subsequently testing power on the same subjects at varying resistances, an average relative percentage of the 1RM-producing peak power values was found by power curve analysis for test standardization. Reliability was assessed (using 11 men) by SM power measurements taken over 3 days on the SM fitted with the timer. An intraclass R (0.998) indicated a high correlation between the 3 separate field-test trials. Finally, 8 male subjects were used to compare SM scores with a criterion measure, the Linea Isokinetic BP station (Loredan Biomedical, Inc., Sacramento CA). A Pearson product moment coefficient found a high correlation between the field test (SM) and Linea power scores (r = 0.987). A 2-tailed dependent t-test between the field and criterion scores was not significant, suggesting that no consistent error variable was present. It can be concluded that this is a valid field test of power for this movement. PMID:11710404

  13. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    NASA Astrophysics Data System (ADS)

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-08-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator.

  14. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    PubMed Central

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-01-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator. PMID:27509823

  15. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis.

    PubMed

    Hensen, B; Kalb, N; Blok, M S; Dréau, A E; Reiserer, A; Vermeulen, R F L; Schouten, R N; Markham, M; Twitchen, D J; Goodenough, K; Elkouss, D; Wehner, S; Taminiau, T H; Hanson, R

    2016-01-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682-686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator. PMID:27509823

  16. Field tests-low input, side-wall vented boiler

    SciTech Connect

    Litzke, W.L.; Butcher, T.A.; Celebi, Y.

    1996-07-01

    The Fan Atomized Burner (FAB) was developed at Brookhaven National Laboratory as part of the Oil Heat Combustion Equipment Technology Program to provide a practical low-firing rate technology leading to new, high efficiency oil-fired appliances. The development of the burner design and results of application testing have been presented in prior oil heat conferences over the past several years. This information is also summarized in a more comprehensive BNL report. The first field trial of a prototype unit was initiated during the 1994-95 heating season. This paper presents the results of the second year of testing, during the 1995-96 heating season. The field tests enable the demonstration of the reliability and performance of the FAB under practical, typical operating conditions. Another important objective of the field test was to demonstrate that the low input is adequate to satisfy the heating and hot water demands of the household. During the first field trial it was shown that at a maximum input rate of 0.4 gph (55,000 Btu/hr) the burner was able to heat a home with over 2,000 square feet of conditioned living space and provide adequate supply of domestic hot water for a family of six. The test is located in Long Island, NY.

  17. Field test of two energetic models for yellow perch

    USGS Publications Warehouse

    Schaeffer, J.S.; Haas, R.C.; Diana, J.S.; Breck, J.E.

    1999-01-01

    Field data from a population of yellow perch Perca flavescens in Saginaw Bay, Lake Huron, were used to evaluate the ability of two energetic models to predict consumption by yellow perch. Field estimates of daily ration for age-l-4 fish during May through October 1987 and 1988 were compared with independent predictions made by the Wisconsin energetic model and an energetic model developed by Karas and Thoresson. Predictions of daily ration using the Wisconsin model were lower than daily rations estimated from field data for all ages, primarily due to poor model-field agreement at temperatures above 22??C. This caused estimates of cumulative consumption from the Wisconsin model to be 25-50% lower than field estimates. Predictions of daily ration by the Karas-Thoresson model agreed with field estimates over a temperature range of 1026??C for age-1-3 yellow perch but not for older fish. Despite improvement, model predictions of cumulative consumption were 2-35% lower than field estimates. Although these tests of predicted and estimated rations may provide insight into which model produced more accurate results, it must be emphasized that field measures of daily ration are also estimates and may be in error, particularly at temperatures above 22??C where gastric evacuation rates were estimated. The Karas-Thoresson modification of the Wisconsin energetic model produced better fits to field ration data and is recommended for model applications.

  18. Size characterization by Sedimentation Field Flow Fractionation of silica particles used as food additives.

    PubMed

    Contado, Catia; Ravani, Laura; Passarella, Martina

    2013-07-25

    Four types of SiO2, available on the market as additives in food and personal care products, were size characterized using Sedimentation Field Flow Fractionation (SdFFF), SEM, TEM and Photon Correlation Spectroscopy (PCS). The synergic use of the different analytical techniques made it possible, for some samples, to confirm the presence of primary nanoparticles (10 nm) organized in clusters or aggregates of different dimension and, for others, to discover that the available information is incomplete, particularly that regarding the presence of small particles. A protocol to extract the silica particles from a simple food matrix was set up, enriching (0.25%, w w(-1)) a nearly silica-free instant barley coffee powder with a known SiO2 sample. The SdFFF technique, in conjunction with SEM observations, made it possible to identify the added SiO2 particles and verify the new particle size distribution. The SiO2 content of different powdered foodstuffs was determined by graphite furnace atomic absorption spectroscopy (GFAAS); the concentrations ranged between 0.006 and 0.35% (w w(-1)). The protocol to isolate the silica particles was so applied to the most SiO2-rich commercial products and the derived suspensions were separated by SdFFF; SEM and TEM observations supported the size analyses while GFAAS determinations on collected fractions permitted element identification.

  19. Decomposition of conifer tree bark under field conditions: effects of nitrogen and phosphorus additions

    NASA Astrophysics Data System (ADS)

    Lopes de Gerenyu, Valentin; Kurganova, Irina; Kapitsa, Ekaterina; Shorokhova, Ekaterina

    2016-04-01

    In forest ecosystems, the processes of decomposition of coarse woody debris (CWD) can contribute significantly to the emission component of carbon (C) cycle and thus accelerate the greenhouse effect and global climate change. A better understanding of decomposition of CWD is required to refine estimates of the C balance in forest ecosystems and improve biogeochemical models. These estimates will in turn contribute to assessing the role of forests in maintaining their long-term productivity and other ecosystems services. We examined the decomposition rate of coniferous bark with added nitrogen (N) and phosphorus (P) fertilizers in experiment under field conditions. The experiment was carried out in 2015 during 17 weeks in Moscow region (54o50'N, 37o36'E) under continental-temperate climatic conditions. The conifer tree bark mixture (ca. 70% of Norway spruce and 30% of Scots pine) was combined with soil and placed in piles of soil-bark substrate (SBS) with height of ca. 60 cm and surface area of ca. 3 m2. The dry mass ratio of bark to soil was 10:1. The experimental design included following treatments: (1) soil (Luvisols Haplic) without bark, (S), (2) pure SBS, (3) SBS with N addition in the amount of 1% of total dry bark mass (SBS-N), and (4) SBS with N and P addition in the amount of 1% of total dry bark mass for each element (SBS-NP). The decomposition rate expressed as CO2 emission flux, g C/m2/h was measured using closed chamber method 1-3 times per week from July to early November using LiCor 6400 (Nebraska, USA). During the experiment, we also controlled soil temperature at depths of 5, 20, 40, and 60 cm below surface of SBS using thermochrons iButton (DS1921G, USA). The pattern of CO2 emission rate from SBS depended strongly on fertilizing. The highest decomposition rates (DecR) of 2.8-5.6 g C/m2/h were observed in SBS-NP treatment during the first 6 weeks of experiment. The decay process of bark was less active in the treatment with only N addition. In this

  20. U.S. field testing programs and results

    SciTech Connect

    Wicks, G.G.

    2000-06-09

    The United States has been active in four major international in-situ or field testing programs over the past two decades, involving the burial of simulated high-level waste forms and package components. These programs are designed to supplement laboratory testing studies in order to obtain the most complete and realistic picture possible of waste glass behavior under realistic repository-relevant conditions.

  1. Field test plan: Buried waste technologies, Fiscal Year 1995

    SciTech Connect

    Heard, R.E.; Hyde, R.A.; Engleman, V.S.; Evans, J.D.; Jackson, T.W.

    1995-06-01

    The US Department of Energy, Office of Technology Development, supports the applied research, development, demonstration, testing, and evaluation of a suite of advanced technologies that, when integrated with commercially available baseline technologies, form a comprehensive remediation system for the effective and efficient remediation of buried waste. The Fiscal Year 1995 effort is to deploy and test multiple technologies from four functional areas of buried waste remediation: site characterization, waste characterization, retrieval, and treatment. This document is the basic operational planning document for the deployment and testing of the technologies that support the field testing in Fiscal Year 1995. Discussed in this document are the scope of the tests; purpose and objective of the tests; organization and responsibilities; contingency plans; sequence of activities; sampling and data collection; document control; analytical methods; data reduction, validation, and verification; quality assurance; equipment and instruments; facilities and utilities; health and safety; residuals management; and regulatory management.

  2. [Immunodiffusion tests in gel media with the addition of polyethyleneglycol 6000 for the serodiagnosis of mycoses].

    PubMed

    Zaror, L; Robles, A M; Negroni, R

    1978-01-01

    Different immunodiffusion techniques with and without the addition of polyetilenglycol 6000 (PEG), were studied to determine its effect on the sensitivity of these reactions. One hundred thirteen sera from patients who suffered or had suffered deep mycoses (paracoccidioidomycosis: 49, histoplasmosis: 25, aspergillosis: 25, candidiasis: 8 and coccidioidomycosis: 6) were examined by the quantitative Ouchterlony's immunodiffusion procedure. Regular medium and media with 2% and 4% PEG were used. Eighty two out of the one hundred thirteen sera were positive for the regular medium and 91 for the medium containing 2% of PEG; furthermore, an increase of 1 or 2 two fold dilutions in the titers was observed in 40% of the sera, for the later media. Twenty one sera from aspergillosis cases were examined by agarose gel immunoelectrophoresis, 80% had more precipitin bands in the medium with 2% of PEG. Thirty four serum samples of patients suffering aspergillosis, paracoccidioidomycosis and histoplasmosis were studied using the agarose electroosmophoresis with the secondary immunodiffusion test. An increase in the number of the anodic bands were observed in 55% while 64% presented more catodic bands, when the PEG medium was used. This results would indicate that the addition of 2% PEG 6000 to the regular medium improves the sensitivity of the immunodiffusion tests for mycoses.

  3. The additive effects of quinine on antidepressant drugs in the forced swimming test in mice.

    PubMed

    Guo, W Y; Todd, K G; Bourin, M; Hascoet, M

    1995-09-01

    The aim of this study was to investigate if quinine plus antidepressant drugs (ADS) leads to an additive effect in the forced swimming test. Quinine (0.125, 0.5 mg/kg) and ADS (subactive doses) were given IP 45 and 30 min, respectively, before the test. When combined with QUIN, all drugs that act via inhibition of 5-HT uptake (imipramine, amitriptyline, citalopram, paroxetine, fluoxetine and fluvoxamine) significantly increased the swimming time of mice. Among trazodone, mianserin and iprindole (atypical ADS), only iprindole combined with quinine decreased the immobility (increased swimming) of the animals. The specific noradrenaline (NA) uptake inhibitors, desipramine and viloxazine, but not maprotiline, were also found to reduce the immobility time when pretreated with quinine. The mixed monoamine oxidase (MAO) inhibitor (pargyline) and MAO-A inhibitor (moclobemide) also shortened the period of immobility whereas the MAO-B inhibitor (nialamide) and the dopamine (DA) uptake inhibitor (bupropion) did not. Quinine's additive effects on several types of ADS is likely a result of blockade of potassium channels.

  4. Intermittent versus Continuous Incremental Field Tests: Are Maximal Variables Interchangeable?

    PubMed

    Carminatti, Lorival J; Possamai, Carlos A P; de Moraes, Marcelo; da Silva, Juliano F; de Lucas, Ricardo D; Dittrich, Naiandra; Guglielmo, Luiz G A

    2013-01-01

    The aim of the present study was to compare physiological responses derived from an incremental progressive field test with a constant speed test i.e. intermittent versus continuous protocol. Two progressive maximum tests (Carminatti`s test (T-CAR) and the Vameval test (T-VAM)), characterized by increasing speed were used. T-CAR is an intermittent incremental test, performed as shuttle runs; while T-VAM is a continuous incremental test performed on an athletic track. Eighteen physically active, healthy young subjects (21.9 ± 2.0 years; 76.5 ± 8.6 kg, 1.78 ± 0.08 m, 11.2 ± 5.4% body fat), volunteered for this study. Subjects performed four different maximum test sessions conducted in the field: two incremental tests and two time to exhaustion tests (TTE) at peak test velocities (PV). No significant differences were found for PV (T-CAR = 15.6 ± 1.2; T-VAM = 15.5 ± 1.3 km·h(-1)) and maximal HR (T-CAR = 195 ± 11; T- VAM = 194 ± 14 bpm). During TTE, there were no significant differences for HR (TTET-CAR and TTET-VAM = 192 ± 12 bpm). However, there was a significant difference in TTE (p = 0.04) (TTET-CAR = 379 ± 84, TTET-VAM = 338 ± 58 s) with a low correlation (r = 0.41). The blood lactate concentration measured at the end of the TTE tests, showed no significant difference (TTET-CAR = 13.2 ± 2.4 vs. TTET-VAM = 12.9 ± 2.4 mmol·l(-1)). Based on the present findings, it is suggested that the maximal variables derived from T-CAR and T-VAM can be interchangeable in the design of training programs. Key pointsT-CAR is an intermittent shuttle run test that predicts the maximal aerobic speed with accuracy, hence, test results could be interchangeable with continuous straight-line tests.T-CAR provides valid field data for evaluating aerobic fitness.In comparison with T-VAM, T-CAR may be a more favourable way to prescribe intermittent training using a shuttle-running protocol.

  5. A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

    NASA Technical Reports Server (NTRS)

    Grady, Joseph E.; Haller, William J.; Poinsatte, Philip E.; Halbig, Michael C.; Schnulo, Sydney L.; Singh, Mrityunjay; Weir, Don; Wali, Natalie; Vinup, Michael; Jones, Michael G.; Patterson, Clark; Santelle, Tom; Mehl, Jeremy

    2015-01-01

    The research and development activities reported in this publication were carried out under NASA Aeronautics Research Institute (NARI) funded project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing." The objective of the project was to conduct evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. The results of the activities are described in three part report. The first part of the report contains the data and analysis of engine system trade studies, which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. The technical scope of activities included an assessment of the feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composites, which were accomplished by fabricating prototype engine components and testing them in simulated engine operating conditions. The manufacturing process parameters were developed and optimized for polymer and ceramic composites (described in detail in the second and third part of the report). A number of prototype components (inlet guide vane (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included turbine nozzle components. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

  6. Comparison of two field tests to estimate maximum aerobic speed.

    PubMed

    Berthoin, S; Gerbeaux, M; Turpin, E; Guerrin, F; Lensel-Corbeil, G; Vandendorpe, F

    1994-08-01

    The measurement of maximal aerobic speed (MAS) and the prediction of maximal oxygen uptake (VO2 max) by means of field tests were carried out on 17 students studying physical education. The subjects underwent a continuous multi-stage track test (Léger and Boucher, 1980), shuttle test (Léger et al., 1984) and VO2 max measurement on a treadmill. The VO2 max values estimated using the track test (56.8 +/- 5.8 ml kg-1 min-1) were not significantly different from the values measured in the treadmill test (56.8 +/- 7.1 ml kg-1 min-1), but were higher than those estimated using the shuttle test (51.1 +/- 5.9 ml kg-1 min-1). The maximal nature of the tests was checked by measurement of heart rate and lactate concentration, taken within 2 min post-test. The means of the MAS observed in the track test (15.8 +/- 1.9 km h-1) and in the treadmill test (15.9 +/- 2.6 km h-1) were not significantly different (P > 0.10). The mean of the shuttle test MAS (13.1 +/- 1 km h-1) was significantly lower (P < 0.01) than those of the other tests. However, the MAS of the shuttle test and track test are linked. The equation for linear regression between MAS values in these two tests is MAStrack = 1.81 x MASshuttle -7.86 (r = 0.91), allowing estimation of one of these MAS values when the other is known. Thus these values may be used within diversified training.

  7. Field Testing Vocational Education Metric Modules. Final Report.

    ERIC Educational Resources Information Center

    Oldsen, Carl F.

    A project was conducted for the following purposes: (1) to develop a workshop training package to prepare vocational education teachers to use vocational subject-specific modules; (2) to train those teachers to use the workshop package; (3) to conduct field tests of the metric modules with experimental and control groups; (4) to analyze, describe,…

  8. A Preliminary Field Test of an Employee Work Passion Model

    ERIC Educational Resources Information Center

    Zigarmi, Drea; Nimon, Kim; Houson, Dobie; Witt, David; Diehl, Jim

    2011-01-01

    Four dimensions of a process model for the formulation of employee work passion, derived from Zigarmi, Nimon, Houson, Witt, and Diehl (2009), were tested in a field setting. A total of 447 employees completed questionnaires that assessed the internal elements of the model in a corporate work environment. Data from the measurements of work affect,…

  9. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... informal application in letter form, signed by the applicant and including the following information: (1.... (3) A brief description of the test antenna system, its estimated effective radiated field and height above ground or average terrain, and the geographic coordinates of its proposed location(s)....

  10. Evaluation Report: Early Childhood Education Program, 1969 Field Test.

    ERIC Educational Resources Information Center

    Appalachia Educational Lab., Charleston, WV.

    Reported are findings from the first year's field test of the home-oriented Appalachia Educational Laboratory (AEL) Early Childhood Education Program for 3-, 4-, and 5-year-olds. The program consists of a 30-minute daily television lesson, a weekly home visit by a paraprofessional, and group instruction once a week in a mobile classroom. The…

  11. 29. PLAN OF THE ARVFS FIELD TEST FACILITY SHOWING BUNKER, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    29. PLAN OF THE ARVFS FIELD TEST FACILITY SHOWING BUNKER, CABLE CHASE, SHIELDING TANK AND FRAME ASSEMBLY. F.C. TORKELSON DRAWING NUMBER 842-ARVFS-701-1. INEL INDEX CODE NUMBER: 075 0701 851 151970. - Idaho National Engineering Laboratory, Advanced Reentry Vehicle Fusing System, Scoville, Butte County, ID

  12. 30. ELEVATION OF ARVFS FIELD TEST FACILITY SHOWING VIEW OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. ELEVATION OF ARVFS FIELD TEST FACILITY SHOWING VIEW OF SOUTH SIDE OF FACILITY, INCLUDING BUNKER, CABLE CHASE, SHIELDING TANK, AND FRAME ASSEMBLY. F.C. TORKELSON DRAWING NUMBER 842-ARVFS-701-2. INEL INDEX CODE NUMBER: 075 0701 851 151971. - Idaho National Engineering Laboratory, Advanced Reentry Vehicle Fusing System, Scoville, Butte County, ID

  13. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Funding of field testing. 35.2262 Section 35.2262 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of...

  14. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Funding of field testing. 35.2262 Section 35.2262 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of...

  15. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Funding of field testing. 35.2262 Section 35.2262 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of...

  16. FIELD TEST OF AIR SPARGING COUPLED WITH SOIL VAPOR EXTRACTION

    EPA Science Inventory

    A controlled field study was designed and conducted to assess the performance of air sparging for remediation of petroleum fuel and solvent contamination in a shallow (3-m deep) groundwater aquifer. Sparging was performed in an insolation test cell (5 m by 3 m by 8-m deep). A soi...

  17. STIS Sparse Field CTE test-internal {Cycle 10}

    NASA Astrophysics Data System (ADS)

    Goudfrooij, Paul

    2001-07-01

    CTE measurements are made using the "sparse field test", along both the serial and parallel axes. This program needs special commanding to provide {a} off-center MSM positionings of some slits, and {b} the ability to read out with any amplifier {A, B, C, or D}. All exposures are internals.

  18. A Simple Soil Percolation Test Device for Field Environmentalists

    ERIC Educational Resources Information Center

    Smith, William H.; Stark, Phillip E.

    1977-01-01

    A primary responsibility of field environmental health workers is evaluation of individual sewage disposal system sites. The authors of this article developed a practical, accurate, and inexpensive measurement device for obtaining reliable percolation test results. Directions for the construction and use of the device are detailed. Drawings…

  19. READ: Field Test of an Educational Approach to Reading Disability.

    ERIC Educational Resources Information Center

    Morsink, Catherine

    This investigation describes a field test of the materials entitled "Reading: An Educational Approach to Disability" (READ), which were developed to aid disabled readers in the beginning stages of learning to decode English print. The subjects were 15 Title I reading teachers working in small groups with 183 second-grade children. The questions of…

  20. Design and testing of the LITE Variable Field Stop mechanism

    NASA Technical Reports Server (NTRS)

    Dillman, Robert A.

    1993-01-01

    The Variable Field Stop (VFS) is a rotary mechanism that reliably positions any of four aperture plates in the optical path of a spaceflight experiment, limiting the amount of light reaching the detectors. This paper discusses the design, operation, and testing of the VFS.

  1. Testing Departure from Additivity in Tukey’s Model using Shrinkage: Application to a Longitudinal Setting

    PubMed Central

    Ko, Yi-An; Mukherjee, Bhramar; Smith, Jennifer A.; Park, Sung Kyun; Kardia, Sharon L.R.; Allison, Matthew A.; Vokonas, Pantel S.; Chen, Jinbo; Diez-Roux, Ana V.

    2014-01-01

    While there has been extensive research developing gene-environment interaction (GEI) methods in case-control studies, little attention has been given to sparse and efficient modeling of GEI in longitudinal studies. In a two-way table for GEI with rows and columns as categorical variables, a conventional saturated interaction model involves estimation of a specific parameter for each cell, with constraints ensuring identifiability. The estimates are unbiased but are potentially inefficient because the number of parameters to be estimated can grow quickly with increasing categories of row/column factors. On the other hand, Tukey’s one degree of freedom (df) model for non-additivity treats the interaction term as a scaled product of row and column main effects. Due to the parsimonious form of interaction, the interaction estimate leads to enhanced efficiency and the corresponding test could lead to increased power. Unfortunately, Tukey’s model gives biased estimates and low power if the model is misspecified. When screening multiple GEIs where each genetic and environmental marker may exhibit a distinct interaction pattern, a robust estimator for interaction is important for GEI detection. We propose a shrinkage estimator for interaction effects that combines estimates from both Tukey’s and saturated interaction models and use the corresponding Wald test for testing interaction in a longitudinal setting. The proposed estimator is robust to misspecification of interaction structure. We illustrate the proposed methods using two longitudinal studies — the Normative Aging Study and the Multi-Ethnic Study of Atherosclerosis. PMID:25112650

  2. Sulfur-free lignins from alkaline pulping tested in mortar for use as mortar additives.

    PubMed

    Nadif, A; Hunkeler, D; Käuper, P

    2002-08-01

    Sulfur-free lignin, obtained through the acid precipitation of black liquor from the soda pulping process, has been tested as water reducer in mortar. It has also been compared to existing commercial additives such as naphthalene sulfonates and lignosulfonates. The ash content and sugar content of these lignins are low in comparison to lignosulfonates, conferring on them higher purity. A procedure for small scale testing derived from the industrial norms SN-EN196 and ASTM (Designation C230-90) is presented. Specifically, all the sulfur-free lignins tested improved the flow of the mortar. Selected flax lignins performed better than lignosulfonates though still less than naphthalene sulfonates. Furthermore, certain hemp lignins gave comparable results to the lignosulfonates. Overall, the straw lignin prepared herein is comparable in performance to commercially available lignins, such as Organocell, Alcell and Curan 100. The plant from which the lignin was isolated, and the process of the pulp mill are the primary influences on the performance of the lignin.

  3. Comparison of two aerobic field tests in young tennis players.

    PubMed

    Fargeas-Gluck, Marie-Agnès; Léger, Luc A

    2012-11-01

    This study compares the maximal responses of a new aerobic tennis field test, the NAVTEN to a known aerobic field test, often used with young tennis players, that is, the continuous multistage 20-m shuttle run test (20-m SRT). The NAVTEN is an intermittent (1-minute/1-minute) multistage test with side-to-side displacements and ball hitting. Ten young elite tennis players aged 12.9 ± 0.3 (mean ± SD) randomly performed both tests and were continuously monitored for heart rate (HR) and oxygen uptake (V[Combining Dot Above]O2) using the Vmax ST (Sensormedics). The 20-m SRT and NAVTEN show similar HRpeak (202 ± 6.1 vs. 208 ± 9.5, respectively) and V[Combining Dot Above]O2peak (54.2 ± 5.9 vs. 54.9 ± 6.0 ml·kg·min). Pearson correlations between both tests were 0.88 and 0.92 for V[Combining Dot Above]O2peak and maximal speed, respectively. The NAVTEN yielded V[Combining Dot Above]O2peak values that are typical for active subjects of that age and are similar to the 20-m SRT supporting its use to measure aerobic fitness of young tennis players in specific and entertaining field conditions. The fact that two-thirds of the tennis players achieved a different ranking (±1 rank) with the NAVTEN and the 20-m SRT suggests that the NAVTEN may be more specific than the 20-m SRT to assess aerobic fitness of tennis players. From a practical point of view, the NAVTEN test is more specific and pedagogical for young tennis players even though both tests yield similar maximal values.

  4. Infrared sensor system (IRSS) laboratory and field test results

    NASA Astrophysics Data System (ADS)

    Ax, George R., Jr.; Buss, James R.

    1997-08-01

    The U.S. Navy Office of Naval Research (ONR) has developed an infrared search and track (IRST) demonstrator system named the infrared sensor system (IRSS). This technology-base sensor was successfully developed and tested both in the laboratory and at-sea. IRSS now is being transitioned to the Naval Sea Systems Command (NAUSEA) IRST Engineering and Manufacturing Development (E&MD) Program, where it will serve, with appropriate modifications, as the engineering development model (EDM) and will be fielded aboard a U.S. Navy ship. This paper summarizes the process of developing and fielding IRSS, describes test results accomplished at sea during 1996, and discusses the technical and engineering lessons associated with design, development and testing of IRSS. Results are presented covering the areas of sensor component and overall system radiometrics (e.g., sensitivity and dynamic range), channel uniformity, stabilization, and optical, electrical and information (i.e., signal processing/track) resolution.

  5. Improving coeliac disease risk prediction by testing non-HLA variants additional to HLA variants

    PubMed Central

    Romanos, Jihane; Rosén, Anna; Kumar, Vinod; Trynka, Gosia; Franke, Lude; Szperl, Agata; Gutierrez-Achury, Javier; van Diemen, Cleo C; Kanninga, Roan; Jankipersadsing, Soesma A; Steck, Andrea; Eisenbarth, Georges; van Heel, David A; Cukrowska, Bozena; Bruno, Valentina; Mazzilli, Maria Cristina; Núñez, Concepcion; Bilbao, Jose Ramon; Mearin, M Luisa; Barisani, Donatella; Rewers, Marian; Norris, Jill M; Ivarsson, Anneli; Boezen, H Marieke; Liu, Edwin; Wijmenga, Cisca

    2014-01-01

    Background The majority of coeliac disease (CD) patients are not being properly diagnosed and therefore remain untreated, leading to a greater risk of developing CD-associated complications. The major genetic risk heterodimer, HLA-DQ2 and DQ8, is already used clinically to help exclude disease. However, approximately 40% of the population carry these alleles and the majority never develop CD. Objective We explored whether CD risk prediction can be improved by adding non-HLA-susceptible variants to common HLA testing. Design We developed an average weighted genetic risk score with 10, 26 and 57 single nucleotide polymorphisms (SNP) in 2675 cases and 2815 controls and assessed the improvement in risk prediction provided by the non-HLA SNP. Moreover, we assessed the transferability of the genetic risk model with 26 non-HLA variants to a nested case–control population (n=1709) and a prospective cohort (n=1245) and then tested how well this model predicted CD outcome for 985 independent individuals. Results Adding 57 non-HLA variants to HLA testing showed a statistically significant improvement compared to scores from models based on HLA only, HLA plus 10 SNP and HLA plus 26 SNP. With 57 non-HLA variants, the area under the receiver operator characteristic curve reached 0.854 compared to 0.823 for HLA only, and 11.1% of individuals were reclassified to a more accurate risk group. We show that the risk model with HLA plus 26 SNP is useful in independent populations. Conclusions Predicting risk with 57 additional non-HLA variants improved the identification of potential CD patients. This demonstrates a possible role for combined HLA and non-HLA genetic testing in diagnostic work for CD. PMID:23704318

  6. Field Testing of a Portable Radiation Detector and Mapping System

    SciTech Connect

    Hofstetter, K.J.; Hayes, D.W.; Eakle, R.F.

    1998-03-01

    Researchers at the Savannah River Site (SRS) have developed a man- portable radiation detector and mapping system (RADMAPS) which integrates the accumulation of radiation information with precise ground locations. RADMAPS provides field personnel with the ability to detect, locate, and characterize nuclear material at a site or facility by analyzing the gamma or neutron spectra and correlating them with position. the man-portable field unit records gamma or neutron count rate information and its location, along with date and time, using an embedded Global Positioning System (GPS). RADMAPS is an advancement in data fusion, integrating several off-the-shelf technologies with new computer software resulting in a system that is simple to deploy and provides information useful to field personnel in an easily understandable form. Decisions on subsequent actions can be made in the field to efficiently use available field resources. The technologies employed in this system include: recording GPS, radiation detection (typically scintillation detectors), pulse height analysis, analog-to-digital converters, removable solid-state (Flash or SRAM) memory cards, Geographic Information System (GIS) software and personal computers with CD-ROM supporting digital base maps. RADMAPS includes several field deployable data acquisition systems designed to simultaneously record radiation and geographic positions. This paper summarizes the capabilities of RADMAPS and some of the results of field tests performed with the system.

  7. Determination of the Path Loss from Passenger Electronic Devices to Radio Altimeter with Additional EMI Test

    NASA Astrophysics Data System (ADS)

    Schüür, J.; Nunes, R. R.

    2012-05-01

    Emitters of current and future wireless ultra wideband technology (UWB) inside the cabin should not interfere with any aircraft system. Especially the radio altimeter (RA) system using antennas mounted outside the fuselage is potentially sensitive to UWB devices in the frequency range between 4.1 and 4.8 GHz. The measurement of the interference path loss (IPL) to the RA is therefore of interest and is presented for different aircraft. The need of a high dynamic setup with low parasitic coupling in the IPL measurement is stressed. In addition, electromagnetic interference (EMI) tests with different transmitted signals are made, showing that the susceptibility of the RA system actually increases with UWB modulation.

  8. Stringent test for non-additive, non-interacting, kinetic energy functionals

    NASA Astrophysics Data System (ADS)

    Jiang, Kaili; Nafziger, Jonathan; Wasserman, Adam

    Partition Density Functional Theory (PDFT) provides an ideal framework for testing and developing new approximations to the non-additive and non-interacting kinetic energy functional (Tsnadd [ {nα } ]), understood as a functional of the set of fragment ground-state densities. We present our progress on both of these fronts: (1) Systematic comparison of the performance of various existing approximations to Tsnadd [ {nα } ] ; and (2) Development of new approximations. We find that a re-parametrization of the GGA enhancement factor employed for the construction of Tsnadd [ {nα } ] through the conjointness conjecture captures essential features of the functional derivatives of Tsnadd [ {nα } ] . A physically-motivated two-orbital approximation for Tsnadd [ {nα } ] is shown to outperform most other approximations for the case of He2, and an intriguing one-parameter formula makes this approximation accurate for all noble-gas diatomics.

  9. Testing with fragrance mix. Is the addition of sorbitan sesquioleate to the constituents useful?

    PubMed

    Frosch, P J; Pilz, B; Burrows, D; Camarasa, J G; Lachapelle, J M; Lahti, A; Menné, T; Wilkinson, J D

    1995-05-01

    In a multicentre study, the value of adding sorbitan sesquioleate (SSO) to the constituents of the 8% fragrance mix (FM) was investigated. In 7 centres, 709 consecutive patients were tested with 2 types of FM from different sources, its 8 constituents with 1% SSO, its 8 constituents without SSO, and 20% SSO. 5 patients (0.71%) reacted to the emulsifier SSO itself, read as definitely allergic on day 3/4. 53 patients reacted to either one of the mixes with an allergic type of reaction. When tested with the constituents without SSO, 41.5% showed an allergic reaction versus 54.7% with SSO. If both types of reactions were considered (allergic and irritant) 38.3% of 73 patients showed a positive "breakdown" result without SSO, versus 54.8% with SSO. The differences were statistically significant. Reactivity to FM constituents was changed in a specific pattern by addition of SSO--irritant reactions increased, particularly for cinnamic alcohol, eugenol, geraniol, oak moss and hydroxycitronellal, whereas others showed only a slight change. Allergic reactions were also increased by SSO, but the rank order of the top 3 sensitizers (isoeugenol, oak moss and eugenol) did not change. Cinnamic alcohol was the only constituent with decreased reactivity after addition of SSO. A positive history of fragrance sensitivity (HFS) was clearly associated with a positive allergic reaction to either the mix or 1 of its constituents (51% versus 28.6% with a negative HFS). Irritant reactions were linked to a negative HFS in a high proportion (64.3%).(ABSTRACT TRUNCATED AT 250 WORDS)

  10. Large Field Photogrammetry Techniques in Aircraft and Spacecraft Impact Testing

    NASA Technical Reports Server (NTRS)

    Littell, Justin D.

    2010-01-01

    The Landing and Impact Research Facility (LandIR) at NASA Langley Research Center is a 240 ft. high A-frame structure which is used for full-scale crash testing of aircraft and rotorcraft vehicles. Because the LandIR provides a unique capability to introduce impact velocities in the forward and vertical directions, it is also serving as the facility for landing tests on full-scale and sub-scale Orion spacecraft mass simulators. Recently, a three-dimensional photogrammetry system was acquired to assist with the gathering of vehicle flight data before, throughout and after the impact. This data provides the basis for the post-test analysis and data reduction. Experimental setups for pendulum swing tests on vehicles having both forward and vertical velocities can extend to 50 x 50 x 50 foot cubes, while weather, vehicle geometry, and other constraints make each experimental setup unique to each test. This paper will discuss the specific calibration techniques for large fields of views, camera and lens selection, data processing, as well as best practice techniques learned from using the large field of view photogrammetry on a multitude of crash and landing test scenarios unique to the LandIR.

  11. Laboratory or Field Tests for Evaluating Firefighters' Work Capacity?

    PubMed Central

    Lindberg, Ann-Sofie; Oksa, Juha; Malm, Christer

    2014-01-01

    Muscle strength is important for firefighters work capacity. Laboratory tests used for measurements of muscle strength, however, are complicated, expensive and time consuming. The aims of the present study were to investigate correlations between physical capacity within commonly occurring and physically demanding firefighting work tasks and both laboratory and field tests in full time (N = 8) and part-time (N = 10) male firefighters and civilian men (N = 8) and women (N = 12), and also to give recommendations as to which field tests might be useful for evaluating firefighters' physical work capacity. Laboratory tests of isokinetic maximal (IM) and endurance (IE) muscle power and dynamic balance, field tests including maximal and endurance muscle performance, and simulated firefighting work tasks were performed. Correlations with work capacity were analyzed with Spearman's rank correlation coefficient (rs). The highest significant (p<0.01) correlations with laboratory and field tests were for Cutting: IE trunk extension (rs = 0.72) and maximal hand grip strength (rs = 0.67), for Stairs: IE shoulder flexion (rs = −0.81) and barbell shoulder press (rs = −0.77), for Pulling: IE shoulder extension (rs = −0.82) and bench press (rs = −0.85), for Demolition: IE knee extension (rs = 0.75) and bench press (rs = 0.83), for Rescue: IE shoulder flexion (rs = −0.83) and bench press (rs = −0.82), and for the Terrain work task: IE trunk flexion (rs = −0.58) and upright barbell row (rs = −0.70). In conclusion, field tests may be used instead of laboratory tests. Maximal hand grip strength, bench press, chin ups, dips, upright barbell row, standing broad jump, and barbell shoulder press were strongly correlated (rs≥0.7) with work capacity and are therefore recommended for evaluating firefighters work capacity. PMID:24614596

  12. Dynamic effect of sodium-water reaction in fast flux test facility power addition sodium pipes

    SciTech Connect

    Huang, S.N.; Anderson, M.J.

    1990-03-01

    The Fast Flux Facility (FFTF) is a demonstration and test facility of the sodium-cooled fast breeder reactor. A power addition'' to the facility is being considered to convert some of the dumped, unused heat into electricity generation. Components and piping systems to be added are sodium-water steam generators, sodium loop extensions from existing dump heat exchangers to sodium-water steam generators, and conventional water/steam loops. The sodium loops can be subjected to the dynamic loadings of pressure pulses that are caused by postulated sodium leaks and subsequent sodium-water reaction in the steam generator. The existing FFTF secondary pipes and the new power addition sodium loops were evaluated for exposure to the dynamic effect of the sodium-water reaction. Elastic and simplified inelastic dynamic analyses were used in this feasibility study. The results indicate that both the maximum strain and strain range are within the allowable limits. Several cycles of the sodium-water reaction can be sustained by the sodium pipes that are supported by ordinary pipe supports and seismic restraints. Expensive axial pipe restraints to withstand the sodium-water reaction loads are not needed, because the pressure-pulse-induced alternating bending stresses act as secondary stresses and the pressure pulse dynamic effect is a deformation-controlled quantity and is self-limiting. 14 refs., 7 figs., 3 tabs.

  13. Critical Assessment of Current Force Fields. Short Peptide Test Case.

    PubMed

    Vymětal, Jiří; Vondrášek, Jiří

    2013-01-01

    The applicability of molecular dynamics simulations for studies of protein folding or intrinsically disordered proteins critically depends on quality of energetic functions-force fields. The four popular force fields for biomolecular simulations, CHARMM22/CMAP, AMBER FF03, AMBER FF99SB, and OPLS-AA/L, were compared in prediction of conformational propensities of all common proteinogenic amino acids. The minimalistic model of terminally block amino acids (dipeptides) was chosen for assessment of side chain effects on backbone propensities. The precise metadynamics simulations revealed striking inconsistency of trends in conformational preferences as manifested by investigated force fields for both backbone and side chains. To trace this disapproval between force fields, the two related AMBER force fields were studied more closely. In the cases of FF99SB and FF03, we uncovered that the distinct tends were driven by different charge models. Additionally, the effects of recent correction for side chain torsion (FF99SB-ILDN) were examined on affected amino acids and exposed significant coupling between free energy profiles and propensities of backbone and side chain conformers. These findings have important consequences for further force field development.

  14. Field tests for evaluating the aerobic work capacity of firefighters.

    PubMed

    Lindberg, Ann-Sofie; Oksa, Juha; Gavhed, Désirée; Malm, Christer

    2013-01-01

    Working as a firefighter is physically strenuous, and a high level of physical fitness increases a firefighter's ability to cope with the physical stress of their profession. Direct measurements of aerobic capacity, however, are often complicated, time consuming, and expensive. The first aim of the present study was to evaluate the correlations between direct (laboratory) and indirect (field) aerobic capacity tests with common and physically demanding firefighting tasks. The second aim was to give recommendations as to which field tests may be the most useful for evaluating firefighters' aerobic work capacity. A total of 38 subjects (26 men and 12 women) were included. Two aerobic capacity tests, six field tests, and seven firefighting tasks were performed. Lactate threshold and onset of blood lactate accumulation were found to be correlated to the performance of one work task (r(s) = -0.65 and -0.63, p<0.01, respectively). Absolute (mL · min(-1)) and relative (mL · kg(-1) · min(-1)) maximal aerobic capacity was correlated to all but one of the work tasks (r(s) = -0.79 to 0.55 and -0.74 to 0.47, p<0.01, respectively). Aerobic capacity is important for firefighters' work performance, and we have concluded that the time to row 500 m, the time to run 3000 m relative to body weight (s · kg(-1)), and the percent of maximal heart rate achieved during treadmill walking are the most valid field tests for evaluating a firefighter's aerobic work capacity. PMID:23844153

  15. Upgraded Near-Field Antenna-Testing System

    NASA Technical Reports Server (NTRS)

    Kunath, Richard R.; Garrett, Michael J.

    1994-01-01

    Upgraded system for near-field testing of large microwave antenna built around commercial automated network analyzer (HP8510) designed for measurement and characterization of microwave circuits and components. Contains highly capable microwave receiver also suitable for far-field and radar-cross-section measurements. Receiver operates in fast-data-acquisition mode at rate of one new data point every millisecond without averaging. Also operates with greater sensitivity by use of averaging feature at time penalty of 0.2 ms per average. Time-domain option added to analyzer enables it to perform time-domain reflectometry.

  16. Multiphase pumps and flow meters -- Status of field testing

    SciTech Connect

    Skiftesvik, P.K.; Svaeren, J.A.

    1995-12-31

    With the development and qualification of multiphase pumps and multiphase flow meters, two new tools have been made available to the oil and gas industry for enhanced production from existing installations or new field developments. This paper presents an overview of the major achievements gained from various test installations carried out the last years using equipment qualified by Framo Engineering AS. The experience from the extensive Field Verification Programmes as described shows that multiphase pumps and meters can operate in various and often harsh well environments providing significant well stream pressure boost or acceptable phase accuracy measurements of oil, water and gas.

  17. ITER Test Blanket Module Error Field Simulation Experiments

    NASA Astrophysics Data System (ADS)

    Schaffer, M. J.

    2010-11-01

    Recent experiments at DIII-D used an active-coil mock-up to investigate effects of magnetic error fields similar to those expected from two ferromagnetic Test Blanket Modules (TBMs) in one ITER equatorial port. The largest and most prevalent observed effect was plasma toroidal rotation slowing across the entire radial profile, up to 60% in H-mode when the mock-up local ripple at the plasma was ˜4 times the local ripple expected in front of ITER TBMs. Analysis showed the slowing to be consistent with non-resonant braking by the mock-up field. There was no evidence of strong electromagnetic braking by resonant harmonics. These results are consistent with the near absence of resonant helical harmonics in the TBM field. Global particle and energy confinement in H-mode decreased by <20% for the maximum mock-up ripple, but <5% at the local ripple expected in ITER. These confinement reductions may be linked with the large velocity reductions. TBM field effects were small in L-mode but increased with plasma beta. The L-H power threshold was unaffected within error bars. The mock-up field increased plasma sensitivity to mode locking by a known n=1 test field (n = toroidal harmonic number). In H-mode the increased locking sensitivity was from TBM torque slowing plasma rotation. At low beta, locked mode tolerance was fully recovered by re-optimizing the conventional DIII-D ``I-coils'' empirical compensation of n=1 errors in the presence of the TBM mock-up field. Empirical error compensation in H-mode should be addressed in future experiments. Global loss of injected neutral beam fast ions was within error bars, but 1 MeV fusion triton loss may have increased. The many DIII-D mock-up results provide important benchmarks for models needed to predict effects of TBMs in ITER.

  18. Plasma injection and capture at electron cyclotron resonance in a mirror system with additional rf fields

    SciTech Connect

    Golovanivskii, K.S.; Dugar-Zhabon, V.D.; Karyaka, V.I.; Milant'ev, V.P.; Turikov, V.A.

    1980-03-01

    Experiments and numerical simulations have been carried out to determine how cyclotron-resonance rf fields in an open magnetic mirror system affect the capture and confinement of a plasma injected along the axis. The results show that at electron cyclotron resonance the fields greatly improve the longitudinal plasma confinement.

  19. The biobehavioral family model: testing social support as an additional exogenous variable.

    PubMed

    Woods, Sarah B; Priest, Jacob B; Roush, Tara

    2014-12-01

    This study tests the inclusion of social support as a distinct exogenous variable in the Biobehavioral Family Model (BBFM). The BBFM is a biopsychosocial approach to health that proposes that biobehavioral reactivity (anxiety and depression) mediates the relationship between family emotional climate and disease activity. Data for this study included married, English-speaking adult participants (n = 1,321; 55% female; M age = 45.2 years) from the National Comorbidity Survey Replication, a nationally representative epidemiological study of the frequency of mental disorders in the United States. Participants reported their demographics, marital functioning, social support from friends and relatives, anxiety and depression (biobehavioral reactivity), number of chronic health conditions, and number of prescription medications. Confirmatory factor analyses supported the items used in the measures of negative marital interactions, social support, and biobehavioral reactivity, as well as the use of negative marital interactions, friends' social support, and relatives' social support as distinct factors in the model. Structural equation modeling indicated a good fit of the data to the hypothesized model (χ(2)  = 846.04, p = .000, SRMR = .039, CFI = .924, TLI = .914, RMSEA = .043). Negative marital interactions predicted biobehavioral reactivity (β = .38, p < .001), as did relatives' social support, inversely (β = -.16, p < .001). Biobehavioral reactivity predicted disease activity (β = .40, p < .001) and was demonstrated to be a significant mediator through tests of indirect effects. Findings are consistent with previous tests of the BBFM with adult samples, and suggest the important addition of family social support as a predicting factor in the model. PMID:24981970

  20. The biobehavioral family model: testing social support as an additional exogenous variable.

    PubMed

    Woods, Sarah B; Priest, Jacob B; Roush, Tara

    2014-12-01

    This study tests the inclusion of social support as a distinct exogenous variable in the Biobehavioral Family Model (BBFM). The BBFM is a biopsychosocial approach to health that proposes that biobehavioral reactivity (anxiety and depression) mediates the relationship between family emotional climate and disease activity. Data for this study included married, English-speaking adult participants (n = 1,321; 55% female; M age = 45.2 years) from the National Comorbidity Survey Replication, a nationally representative epidemiological study of the frequency of mental disorders in the United States. Participants reported their demographics, marital functioning, social support from friends and relatives, anxiety and depression (biobehavioral reactivity), number of chronic health conditions, and number of prescription medications. Confirmatory factor analyses supported the items used in the measures of negative marital interactions, social support, and biobehavioral reactivity, as well as the use of negative marital interactions, friends' social support, and relatives' social support as distinct factors in the model. Structural equation modeling indicated a good fit of the data to the hypothesized model (χ(2)  = 846.04, p = .000, SRMR = .039, CFI = .924, TLI = .914, RMSEA = .043). Negative marital interactions predicted biobehavioral reactivity (β = .38, p < .001), as did relatives' social support, inversely (β = -.16, p < .001). Biobehavioral reactivity predicted disease activity (β = .40, p < .001) and was demonstrated to be a significant mediator through tests of indirect effects. Findings are consistent with previous tests of the BBFM with adult samples, and suggest the important addition of family social support as a predicting factor in the model.

  1. Additive effects of clonidine and antidepressant drugs in the mouse forced-swimming test.

    PubMed

    Malinge, M; Bourin, M; Colombel, M C; Larousse, C

    1988-01-01

    In the mouse forced-swimming model, dose-dependent reversal of immobility was induced by the alpha-agonist clonidine given IP 30 min before testing. In addition, three preferential inhibitors of 5-HT uptake (citalopram, indalpine and fluvoxamine) had similar activity in the dose range 8-16 mg/kg as did the 5-HT1 agonist 8-OH-DPAT (1-4 mg/kg). Pretreatment with alpha-methyl-paratyrosine (100 mg/kg) did not prevent clonidine (1 mg/kg) action, suggesting that there was mediation by alpha post-junctional receptors. The effect of clonidine was unaltered by prazosin (2 mg/kg) and reversed by yohimbine (4 mg/kg) and 5-MeODMT (1 mg/kg), whereas it was potentiated by reserpine (2.5 mg/kg), methysergide (2 mg/kg) and ketanserin (8 mg/kg). Moreover, an ineffective dose of clonidine (0.06 mg/kg at 45 min pre-testing) made active subthreshold doses of various antidepressants (given at 30 min pre-testing): imipramine (4 mg/kg), amitriptyline (1 mg/kg), maprotiline (8 mg/kg), citalopram (2 mg/kg), indalpine, fluvoxamine and mianserin (4 mg/kg), viloxazine (2 mg/kg). Similar interactions were found with iprindole and nialamide (32 mg/kg), which were inactive alone up to 64 mg/kg, and 8-OH-DPAT (0.5 mg/kg) but not with major and minor tranquillizers. It is suggested that one effect of antidepressants might be the triggering of different relationships between alpha-2 and 5-HT mechanisms.

  2. SMART wind turbine rotor. Design and field test

    SciTech Connect

    Berg, Jonathan Charles; Resor, Brian Ray; Paquette, Joshua A.; White, Jonathan Randall

    2014-01-01

    The Wind Energy Technologies department at Sandia National Laboratories has developed and field tested a wind turbine rotor with integrated trailing-edge flaps designed for active control of rotor aerodynamics. The SMART Rotor project was funded by the Wind and Water Power Technologies Office of the U.S. Department of Energy (DOE) and was conducted to demonstrate active rotor control and evaluate simulation tools available for active control research. This report documents the design, fabrication, and testing of the SMART Rotor. This report begins with an overview of active control research at Sandia and the objectives of this project. The SMART blade, based on the DOE / SNL 9-meter CX-100 blade design, is then documented including all modifications necessary to integrate the trailing edge flaps, sensors incorporated into the system, and the fabrication processes that were utilized. Finally the test site and test campaign are described.

  3. Field Testing: Independent, Accredited Testing and Validation for the Wind Industry (Fact Sheet)

    SciTech Connect

    Not Available

    2011-11-01

    This fact sheet describes the field testing capabilities at the National Wind Technology Center (NWTC). NREL's specialized facilities and personnel at the NWTC provide the U.S. wind industry with scientific and engineering support that has proven critical to the development of wind energy for U.S. energy needs. The NWTC's specialized field-testing capabilities have evolved over 30 years of continuous support by the U.S. Department of Energy Wind and Hydropower Technologies Program and long standing industry partnerships. The NWTC provides wind industry manufacturers, developers, and operators with turbine and component testing all in one convenient location. Although industry utilizes sophisticated modeling tools to design and optimize turbine configurations, there are always limitations in modeling capabilities, and testing is a necessity to ensure performance and reliability. Designs require validation and testing is the only way to determine if there are flaws. Prototype testing is especially important in capturing manufacturing flaws that might require fleet-wide retrofits. The NWTC works with its industry partners to verify the performance and reliability of wind turbines that range in size from 400 Watts to 3 megawatts. Engineers conduct tests on components and full-scale turbines in laboratory environments and in the field. Test data produced from these tests can be used to validate turbine design codes and simulations that further advance turbine designs.

  4. Opon Gas Field, Colombia: Part I - geoscience description, well design and well test performance

    SciTech Connect

    Stone, D.M.; Huffmyer, W.A.; Greener, J.M.; Mamerow, B.S.

    1996-12-31

    This paper describes the geoscience and engineering aspects of the Opon Gas Field located in the Middle Magdalena Basin, Colombia. The remoteness and extreme downhole conditions make the drilling, completion, testing and geoscience interpretation of the two most recent Opon wells technically very challenging. Multiple faults, steep dips, rugged topography, a sensitive jungle environment and variable surface velocities complicate field definition. A full assessment of the commercial potential of the reservoir requires additional development drilling. Now in the early development stages, the Opon Gas Field has first production scheduled for late 1996.

  5. Mathematical model of testing of pipeline integrity by thermal fields

    SciTech Connect

    Vaganova, Nataliia

    2014-11-18

    Thermal fields testing at the ground surface above a pipeline are considered. One method to obtain and investigate an ideal thermal field in different environments is a direct numerical simulation of heat transfer processes taking into account the most important physical factors. In the paper a mathematical model of heat propagation from an underground source is described with accounting of physical factors such as filtration of water in soil and solar radiation. Thermal processes are considered in 3D origin where the heat source is a pipeline with constant temperature and non-uniform isolated shell (with 'damages'). This problem leads to solution of heat diffusivity equation with nonlinear boundary conditions. Approaches to analysis of thermal fields are considered to detect damages.

  6. The blue field entoptic test with normal patients.

    PubMed

    Potter, J W; Norden, L C

    1983-12-01

    One hundred normal patients were evaluated with the Blue Field Entoptoscope test. Of those one hundred patients, ninety-nine were able to describe the appearance of their own leukocytes. The methodology did not permit encouraging or coaching patients to see their leukocytes. Of the ninety-nine who could perceive their own leukocytes, nineteen 19.19%) were unable to perceive an approximately equal number in each of the four quadrants of the blue field of light which is divided by a reticle. These patients who did not see an equal number of leukocytes in all four quadrants were generally older than those who saw an equal number of leukocytes. The results indicate that if the Blue Field Entoptoscope is to be used in clinical practice or research, it is useful to standardize the instrument for the population studied. In particular, the instrument should be standardized for age. PMID:6655191

  7. Incorporating Spatial Models in Visual Field Test Procedures

    PubMed Central

    Rubinstein, Nikki J.; McKendrick, Allison M.; Turpin, Andrew

    2016-01-01

    Purpose To introduce a perimetric algorithm (Spatially Weighted Likelihoods in Zippy Estimation by Sequential Testing [ZEST] [SWeLZ]) that uses spatial information on every presentation to alter visual field (VF) estimates, to reduce test times without affecting output precision and accuracy. Methods SWeLZ is a maximum likelihood Bayesian procedure, which updates probability mass functions at VF locations using a spatial model. Spatial models were created from empirical data, computational models, nearest neighbor, random relationships, and interconnecting all locations. SWeLZ was compared to an implementation of the ZEST algorithm for perimetry using computer simulations on 163 glaucomatous and 233 normal VFs (Humphrey Field Analyzer 24-2). Output measures included number of presentations and visual sensitivity estimates. Results There was no significant difference in accuracy or precision of SWeLZ for the different spatial models relative to ZEST, either when collated across whole fields or when split by input sensitivity. Inspection of VF maps showed that SWeLZ was able to detect localized VF loss. SWeLZ was faster than ZEST for normal VFs: median number of presentations reduced by 20% to 38%. The number of presentations was equivalent for SWeLZ and ZEST when simulated on glaucomatous VFs. Conclusions SWeLZ has the potential to reduce VF test times in people with normal VFs, without detriment to output precision and accuracy in glaucomatous VFs. Translational Relevance SWeLZ is a novel perimetric algorithm. Simulations show that SWeLZ can reduce the number of test presentations for people with normal VFs. Since many patients have normal fields, this has the potential for significant time savings in clinical settings. PMID:26981329

  8. Lidar Tracking of Multiple Fluorescent Tracers: Method and Field Test

    NASA Technical Reports Server (NTRS)

    Eberhard, Wynn L.; Willis, Ron J.

    1992-01-01

    Past research and applications have demonstrated the advantages and usefulness of lidar detection of a single fluorescent tracer to track air motions. Earlier researchers performed an analytical study that showed good potential for lidar discrimination and tracking of two or three different fluorescent tracers at the same time. The present paper summarizes the multiple fluorescent tracer method, discusses its expected advantages and problems, and describes our field test of this new technique.

  9. On-site cell field test support program

    NASA Astrophysics Data System (ADS)

    Staniunas, J. W.; Merten, G. P.

    1982-09-01

    Utility sites for data monitoring were reviewed and selected. Each of these sites will be instrumented and its energy requirements monitored and analyzed for one year prior to the selection of 40 Kilowatt fuel cell field test sites. Analyses in support of the selection of sites for instrumentation shows that many building sectors offered considerable market potential. These sectors include nursing home, health club, restaurant, industrial, hotel/motel and apartment.

  10. Field-testing UV disinfection of drinking water

    SciTech Connect

    Gadgil, A.; Drescher, A.; Greene, D.; Miller, P.; Motau, C.; Stevens, F.

    1997-09-01

    A recently invented device, ``UV Waterworks,`` uses ultraviolet (UV) light to disinfect drinking water. Its novel features are: low cost, robust design, rapid disinfection, low electricity use, low maintenance, high flow rate and ability to work with unpressurized water sources. The device could service a community of 1,000 persons, at an annual total cost of less than 10 US cents per person. UV Waterworks has been successfully tested in the laboratory. Limited field trials of an early version of the device were conducted in India in 1994--95. Insights from these trials led to the present design. Extended field trials of UV Waterworks, initiated in South Africa in February 1997, will be coordinated by the South African Center for Essential Community Services (SACECS), with technical and organizational support from Lawrence Berkeley National Laboratory(LBNL) and the Natural Resources Defense Council (both US). The first of the eight planned sites of the year long trial is an AIDS hospice near Durban. Durban metro Water and LBNL lab-tested a UV Waterworks unit prior to installing it at the hospice in August, 1997. The authors describe the field test plans and preliminary results from Durban.

  11. Performance evaluation of infrared imaging system in field test

    NASA Astrophysics Data System (ADS)

    Wang, Chensheng; Guo, Xiaodong; Ren, Tingting; Zhang, Zhi-jie

    2014-11-01

    Infrared imaging system has been applied widely in both military and civilian fields. Since the infrared imager has various types and different parameters, for system manufacturers and customers, there is great demand for evaluating the performance of IR imaging systems with a standard tool or platform. Since the first generation IR imager was developed, the standard method to assess the performance has been the MRTD or related improved methods which are not perfect adaptable for current linear scanning imager or 2D staring imager based on FPA detector. For this problem, this paper describes an evaluation method based on the triangular orientation discrimination metric which is considered as the effective and emerging method to evaluate the synthesis performance of EO system. To realize the evaluation in field test, an experiment instrument is developed. And considering the importance of operational environment, the field test is carried in practical atmospheric environment. The test imagers include panoramic imaging system and staring imaging systems with different optics and detectors parameters (both cooled and uncooled). After showing the instrument and experiment setup, the experiment results are shown. The target range performance is analyzed and discussed. In data analysis part, the article gives the range prediction values obtained from TOD method, MRTD method and practical experiment, and shows the analysis and results discussion. The experimental results prove the effectiveness of this evaluation tool, and it can be taken as a platform to give the uniform performance prediction reference.

  12. Aerobic and anaerobic in vitro testing of feed additives claiming to detoxify deoxynivalenol and zearalenone.

    PubMed

    Hahn, Irene; Kunz-Vekiru, Elisavet; Twarużek, Magdalena; Grajewski, Jan; Krska, Rudolf; Berthiller, Franz

    2015-01-01

    Deoxynivalenol (DON) and zearalenone (ZEN) are mycotoxins produced by fungi of the genus Fusarium which frequently contaminate maize and grain cereals. Mycotoxin-contaminated feed endangers animal health and leads to economic losses in animal production. Several mycotoxin elimination strategies, including the use of commercially available DON and ZEN detoxifying agents, have been developed. However, frequently there is no scientific proof of the efficacy of such adsorbents and degrading products. We therefore tested 20 commercially available products claiming to detoxify DON and/or ZEN either by biodegradation (4 products) or a combination of degradation and adsorption (16 products) under aerobic and anaerobic conditions at approx. pH 7. Under the applied conditions, a complete reduction of DON and consequent formation of the known non-toxic metabolite DOM-1 was exclusively observed in samples taken from the anaerobic degradation experiment of one product. For all other products, incubated under aerobic and anaerobic conditions, a maximum DON reduction of 17% after 72 h of incubation was detected. Aerobic and anaerobic incubation of only one tested product resulted in complete ZEN reduction as well as in the formation of the less-toxic metabolites DHZEN and HZEN. With this product, 68-97% of the toxin was metabolised within 3 h. After 24 h, a ZEN reduction ≥ 60% was obtained with four additional products during aerobic incubation only. Six of the 20 investigated products produced α- and/or β-ZEL, which are metabolites showing similar oestrogenic activity compared to ZEN. Aerobic and anaerobic degradation to unknown metabolites with unidentified toxicity was obtained with 10 and 3 products, respectively. The results of our study demonstrate the importance of in vitro experiments to critically screen agents claiming mycotoxin detoxification.

  13. Field test comparison of natural gas engine exhaust valves

    SciTech Connect

    Bicknell, W.B.; Hay, S.C.; Shade, W.N.; Statler, G.R.

    1996-12-31

    As part of a product improvement program, an extensive spark-ignited, turbocharged, natural gas engine exhaust valve test program was conducted using laboratory and field engines. Program objectives were to identify a valve and seat insert combination that increased mean time between overhauls (MTBO) while reducing the risk of premature valve cracking and failure. Following a thorough design review, a large number of valve and seat insert configurations were tested in a popular 900 RPM, 166 BHP (0.123 Mw) per cylinder industrial gas engine series. Material, head geometry, seat angle and other parameters were compared. Careful in-place measurements and post-test inspections compared various configurations and identified optimal exhaust valving for deployment in new units and upgrades of existing engines.

  14. Evaluation of laser ultrasonic testing for inspection of metal additive manufacturing

    NASA Astrophysics Data System (ADS)

    Everton, Sarah; Dickens, Phill; Tuck, Chris; Dutton, Ben

    2015-03-01

    Additive Manufacturing (AM) offers a number of benefits over conventional processes. However, in order for these benefits to be realised, further development and integration of suitable monitoring and closed loop control systems are needed. Laser Ultrasonic Testing (LUT) is an inspection technology which shows potential for in-situ monitoring of metallic AM processes. Non-contact measurements can be performed on curved surfaces and in difficult to reach areas, even at elevated temperatures. Interrogation of each build layer generates defect information which can be used to highlight processing errors and allow for real-time modification of processing parameters, enabling improved component quality and yield. This study evaluates the use of laser-generated surface waves to detect artificially generated defects in titanium alloy (Ti- 6Al-4V) samples produced by laser-based Powder Bed Fusion. The trials undertaken utilise the latest LUT equipment, recently installed at Manufacturing Technology Centre which is capable of being controlled remotely. This will allow the system to optimise or adapt "on-the-fly", simplifying the eventual integration of the system within an AM machine.

  15. Field assessments in conjunction with whole effluent toxicity testing

    SciTech Connect

    La Point, T.W.; Waller, W.T.

    2000-01-01

    Whole effluent toxicity (WET) tests are widely used to assess potential effects of wastewater discharges on aquatic life. This paper represents a summary of chapters in a 1996 Society of Environmental Toxicology and Chemistry-sponsored workshop and a literature review concerning linkages between WET testing and associated field biomonitoring. Most published studies thus far focus primarily on benthic macroinvertebrates and on effluent-dominated stream systems in which effluents demonstrate little or no significant acute toxicity. Fewer studies examine WET test predictability in other aquatic ecosystems (e.g., wetlands, estuaries, large rivers) or deal with instream biota such as fish and primary producers. Published results indicate that standards for the usual WET freshwater test species, Ceriodaphnia dubia and Pimephales promelas, may not always protect most of the species inhabiting a receiving stream. Although WET tests are useful in predicting aquatic individual responses, they are not meant to directly measure natural population or community responses. Further, they do not address bioconcentration or bioaccumulation of hydrophobic compounds; do not assess eutrophication effects in receiving systems; and lastly, do not reflect genotoxic effects or function to test for endocrine-disrupting chemicals. Consequently, a more direct evaluation of ecosystem health, using bioassessment techniques, may be needed to properly evaluate aquatic systems affected by wastewater discharges.

  16. Review and evaluation of literature on testing of chemical additives for scale control in geothermal fluids. Final report

    SciTech Connect

    Crane, C.H.; Kenkeremath, D.C.

    1981-01-01

    A selected group of reported tests of chemical additives in actual geothermal fluids are reviewed and evaluated to summarize the status of chemical scale-control testing and identify information and testing needs. The task distinguishes between scale control in the cooling system of a flash plant and elsewhere in the utilization system due to the essentially different operating environments involved. Additives for non-cooling geothermal fluids are discussed by scale type: silica, carbonate, and sulfide.

  17. Goodness-of-fit tests for the additive risk model with (p > 2)-dimensional time-invariant covariates.

    PubMed

    Kim, J; Song, M S; Lee, S

    1998-01-01

    This paper presents methods for checking the goodness-of-fit of the additive risk model with p(> 2)-dimensional time-invariant covariates. The procedures are an extension of Kim and Lee (1996) who developed a test to assess the additive risk assumption for two-sample censored data. We apply the proposed tests to survival data from South Wales nikel refinery workers. Simulation studies are carried out to investigate the performance of the proposed tests for practical sample sizes. PMID:9880997

  18. Sensitization to Food Additives in Patients with Allergy: A Study Based on Skin Test and Open Oral Challenge.

    PubMed

    Moghtaderi, Mozhgan; Hejrati, Zinatosadat; Dehghani, Zahra; Dehghani, Faranak; Kolahi, Niloofar

    2016-06-01

    There has been a great increase in the consumption of various food additives in recent years. The purpose of this study was to identify the incidence of sensitization to food additives by using skin prick test in patients with allergy and to determine the concordance rate between positive skin tests and oral challenge in hypersensitivity to additives. This cross-sectional study included 125 (female 71, male 54) patients aged 2-76 years with allergy and 100 healthy individuals. Skin tests were performed in both patient and control groups with 25 fresh food additives. Among patients with allergy, 22.4% showed positive skin test at least to one of the applied materials. Skin test was negative to all tested food additives in control group. Oral food challenge was done in 28 patients with positive skin test, in whom 9 patients showed reaction to culprit (Concordance rate=32.1%). The present study suggested that about one-third of allergic patients with positive reaction to food additives showed positive oral challenge; it may be considered the potential utility of skin test to identify the role of food additives in patients with allergy.

  19. Sensitization to Food Additives in Patients with Allergy: A Study Based on Skin Test and Open Oral Challenge.

    PubMed

    Moghtaderi, Mozhgan; Hejrati, Zinatosadat; Dehghani, Zahra; Dehghani, Faranak; Kolahi, Niloofar

    2016-06-01

    There has been a great increase in the consumption of various food additives in recent years. The purpose of this study was to identify the incidence of sensitization to food additives by using skin prick test in patients with allergy and to determine the concordance rate between positive skin tests and oral challenge in hypersensitivity to additives. This cross-sectional study included 125 (female 71, male 54) patients aged 2-76 years with allergy and 100 healthy individuals. Skin tests were performed in both patient and control groups with 25 fresh food additives. Among patients with allergy, 22.4% showed positive skin test at least to one of the applied materials. Skin test was negative to all tested food additives in control group. Oral food challenge was done in 28 patients with positive skin test, in whom 9 patients showed reaction to culprit (Concordance rate=32.1%). The present study suggested that about one-third of allergic patients with positive reaction to food additives showed positive oral challenge; it may be considered the potential utility of skin test to identify the role of food additives in patients with allergy. PMID:27424134

  20. Government regulation and public opposition create high additional costs for field trials with GM crops in Switzerland.

    PubMed

    Bernauer, Thomas; Tribaldos, Theresa; Luginbühl, Carolin; Winzeler, Michael

    2011-12-01

    Field trials with GM crops are not only plant science experiments. They are also social experiments concerning the implications of government imposed regulatory constraints and public opposition for scientific activity. We assess these implications by estimating additional costs due to government regulation and public opposition in a recent set of field trials in Switzerland. We find that for every Euro spent on research, an additional 78 cents were spent on security, an additional 31 cents on biosafety, and an additional 17 cents on government regulatory supervision. Hence the total additional spending due to government regulation and public opposition was around 1.26 Euros for every Euro spent on the research per se. These estimates are conservative; they do not include additional costs that are hard to monetize (e.g. stakeholder information and dialogue activities, involvement of various government agencies). We conclude that further field experiments with GM crops in Switzerland are unlikely unless protected sites are set up to reduce these additional costs.

  1. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... between control stations and pods; (d) Pressure test the blind or blind-shear ram BOP during stump tests and at all casing points; (e) The interval between any blind or blind-shear ram BOP pressure tests may not exceed 30 days; (f) Pressure test variable bore-pipe ram BOPs against the largest and...

  2. Relation of field independence and test-item format to student performance on written piagetian tests

    NASA Astrophysics Data System (ADS)

    Ló; Pez-Rupérez, F.; Palacios, C.; Sanchez, J.

    In this study we have investigated the relationship between the field-dependence-independence (FDI) dimension as measured by the Group Embedded Figures Test (GEFT) and subject performance on the Longeot test, a pencil-and-paper Piagetian test, through the open or closed format of its items. The sample consisted of 141 high school students. Correlation and variance analysis show that the FDI dimension and GEFT correlate significantly on only those items on the Longeot test that require formal reasoning. The effect of open- or closed-item format is found exclusively for formal items; only the open format discriminates significantly (at the 0.01 level) between the field-dependent and -independent subjects performing on this type of item. Some implications of these results for science education are discussed.

  3. Field tests of 2- and 40-tube condensers at the East Mesa Geothermal Test Site

    SciTech Connect

    Murphy, R.W.; Domingo, N.

    1982-05-01

    Two water-cooled isobutane condensers, one with 2 tubes and one with 40 tubes, were subjected to field tests at the East Mesa Geothermal Test Site to assess relative heat transfer performance in both surface evaporator and direct-contact evaporator modes. The five groups of tests established that field performance was below earlier laboratory-determined levels and that direct-contact evaporator mode performance was poorer than that for the surface evaporator mode. In all test situations, fluted condenser tubes performed better than smooth condenser tubes. Cooling water quality had no significant effect on performance, but brine preflash in the direct-contact mode did promote some relative performance improvement. Important implications of these results for binary geothermal power plants are that (1) working-fluid-side impurities can significantly degrade heat transfer performance of the power plant condensers and (2) provisions for minimizing such impurities may be required.

  4. The Synthesis of Structural Responses Using Experimentally Measured Frequency Response Functions and Field Test Data

    SciTech Connect

    CAP,JEROME S.; NELSON,CURTIS F.

    2000-11-17

    This paper presents an analysis technique used to generate the structural response at locations not measured during the ejection of a captive-carried store. The ejection shock event is complicated by the fact that forces may be imparted to the store at eight distinct locations. The technique derives forcing functions by combining the initial field test data for a limited number of measurement locations with Frequency Response Functions (FRFs) measured using a traditional modal-type impact (tap) test at the same locations. The derived forcing functions were then used with tap test FRFs measured at additional locations of interest to produce the desired response data.

  5. Environmental assessment of the 40 kilowatt fuel cell system field test operation

    NASA Technical Reports Server (NTRS)

    Bollenbacher, G.

    1982-01-01

    This environmental assessment examines the potential environmental consequences, both adverse and beneficial, of the 40 kW fuel cell system system field test operation. The assessment is of necessity generic in nature since actual test sites were not selected. This assessment provides the basis for determining the need for an environmental impact statement. In addition, this assessment provides siting criteria to avoid or minimize negative environmental impacts and standards for determining candidate test sites, if any, for which site specific assessments may be required.

  6. High temperature superconducting axial field magnetic coupler: realization and test

    NASA Astrophysics Data System (ADS)

    Belguerras, L.; Mezani, S.; Lubin, T.; Lévêque, J.; Rezzoug, A.

    2015-09-01

    Contactless torque transmission through a large airgap is required in some industrial applications in which hermetic isolation is necessary. This torque transmission usually uses magnetic couplers, whose dimension strongly depends on the airgap flux density. The use of high temperature superconducting (HTS) coils to create a strong magnetic field may constitute a solution to reduce the size of the coupler. It is also possible to use this coupler to replace a torque tube in transmitting the torque produced by a HTS motor to its load. This paper presents the detailed construction and tests of an axial field HTS magnetic coupler. Pancake coils have been manufactured from BSCCO tape and used in one rotor of the coupler. The second rotor is mainly composed of NdFeB permanent magnets. Several tests have been carried out showing that the constructed coupler is working properly. A 3D finite element (FE) model of the studied coupler has been developed. Airgap magnetic field and torque measurements have been carried out and compared to the FE results. It has been shown that the measured and the computed quantities are in satisfactory agreement.

  7. Validity of Selected Lab and Field Tests of Physical Working Capacity.

    ERIC Educational Resources Information Center

    Burke, Edmund J.

    The validity of selected lab and field tests of physical working capacity was investigated. Forty-four male college students were administered a series of lab and field tests of physical working capacity. Lab tests include a test of maximum oxygen uptake, the PWC 170 test, the Harvard Step Test, the Progressive Pulse Ratio Test, Margaria Test of…

  8. Field test of a post-closure radiation monitor

    SciTech Connect

    Reed, S.; Christy, C.E.; Heath, R.E.

    1995-12-01

    The DOE is conducting remedial actions at many sites contaminated with radioactive materials. After closure of these sites, long-term subsurface monitoring is typically required by law. This monitoring is generally labor intensive and expensive using conventional sampling and analysis techniques. The U.S. Department of Energy`s Morgantown Energy Technology Center (METC) has contracted with Babcock and Wilcox to develop a Long-Term Post-Closure Radiation Monitoring System (LPRMS) to reduce these monitoring costs. A prototype LPRMS probe was built, and B&W and FERMCO field tested this monitoring probe at the Fernald Environmental Management Project in the fall of 1994 with funding from the DOE`s Office of Technology Development (EM-50) through METC. The system was used to measure soil and water with known uranium contamination levels, both in drums and in situ at depths up to 3 meters. For comparison purposes, measurements were also performed using a more conventional survey probe with a sodium iodide scintillator directly butt-coupled to detection electronics. This paper presents a description and the results of the field tests. The results were used to characterize the lower detection limits, precision and bias of the system, which allowed the DOE to judge the monitoring system`s ability to meet its long-term post-closure radiation monitoring needs. Based on the test results, the monitoring system has been redesigned for fabrication and testing in a potential Phase III of this program. If the DOE feels that this system can meet its needs and chooses to continue into Phase III of this program, this redesigned full scale prototype system will be built and tested for a period of approximately a year. Such a system can be used at a variety of radioactively contaminated sites.

  9. Near-field testing of the 30 GHz TRW proof-of-concept multibeam antenna

    NASA Technical Reports Server (NTRS)

    Kunath, R. R., Jr.; Zakrajsek, R. J.

    1986-01-01

    Near-field testing was conducted on the 30 GHz TRW proof-of-concept (POC) Multibeam Antenna (MBA). The TRW POC MBA is a dual offset Cassegrain reflector system using a 2.7 m main reflector. This configuration was selected to assess the ability to create both multiple fixed and scanned spot beams. The POC configuration investigated frequency reuse via spatial separation of beams, polarization selectivity and time division multiple access scanning at 30 GHz. Measurements of directivity, sidelobe level, and pattern were made at NASA Lewis Research Center's Near-Field Antenna Test Facility. Presented in this paper are complete results of these measurements. Included is a detailed discussion of all testing procedures and parameters. Results of additional testing used to evaluate diffraction effects of the subreflector and distortions of the main reflector are also presented.

  10. Site Guidelines for a Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Sassani, D.; Kuhlman, K. L.; Freeze, G. A.; MacKinnon, R. J.; Perry, F.

    2015-12-01

    The US DOE Office of Nuclear Energy Used Nuclear Fuel Disposition Campaign (UFDC) is initiating a Deep Borehole Field Test (DBFT), without use of any radioactive waste, to evaluate the geoscience of the approach and technical capabilities for implementation. DOE has identified Sandia National Laboratories (SNL) as the Technical Lead for the UFDC DBFT Project, with the role of supporting DOE in (i) developing the overall DBFT Project Plan, (ii) management and integration of all DBFT Project activities, and (iii) providing Project technical guidance to DOE, other DOE National Laboratories, and university partners. The DBFT includes drilling one Characterization Borehole (CB-8.5" diameter), followed by an optional Field Test Borehole (FTB), to a depth of about 5,000 m (16,400 feet) into crystalline basement rock in a geologically stable continental location. The DBFT CB will be drilled and completed to facilitate downhole scientific testing and analyses. If site conditions are found to be favorable, DOE may drill the larger-diameter (17") FTB to facilitate proof-of-concept of handling, emplacement, and retrieval activities using surrogate waste containers. Guidelines for favorable DBFT site geohydrochemical and geomechanical conditions will be discussed and status of the DBFT Project will be provided. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2015-6426A.

  11. Test plan for FY-94 digface characterization field experiments

    SciTech Connect

    Josten, N.E.; Roybal, L.G.

    1994-08-01

    The digface characterization concept has been under development at the Idaho National Engineering Laboratory (INEL) since fiscal year (FY) 1992 through the support of the Buried Waste Integrated Demonstration Program. A digface characterization system conducts continuous subsurface characterization simultaneously with retrieval of hazardous and radioactive waste from buried waste sites. The system deploys multiple sensors at the retrieval operation digface and collects data that provide a basis for detecting, locating, and classifying buried materials and hazardous conditions before they are disturbed by the retrieval equipment. This test plan describes ongoing efforts to test the digface characterization concept at the INEL`s Cold Test Pit using a simplified prototype deployment apparatus and off-the-shelf sensors. FY-94 field experiments will explore problems in object detection and classification. Detection and classification of objects are fundamental to three of the four primary functions of digface characterization during overburden removal. This test plan establishes procedures for collecting and validating the digface characterization data sets. Analysis of these data will focus on testing and further developing analysis methods for object detection and classification during overburden removal.

  12. Flow-Field Survey in the Test Region of the SR-71 Aircraft Test Bed Configuration

    NASA Technical Reports Server (NTRS)

    Mizukami, Masashi; Jones, Daniel; Weinstock, Vladimir D.

    2000-01-01

    A flat plate and faired pod have been mounted on a NASA SR-71A aircraft for use as a supersonic flight experiment test bed. A test article can be placed on the flat plate; the pod can contain supporting systems. A series of test flights has been conducted to validate this test bed configuration. Flight speeds to a maximum of Mach 3.0 have been attained. Steady-state sideslip maneuvers to a maximum of 2 deg have been conducted, and the flow field in the test region has been surveyed. Two total-pressure rakes, each with two flow-angle probes, have been placed in the expected vicinity of an experiment. Static-pressure measurements have been made on the flat plate. At subsonic and low supersonic speeds with no sideslip, the flow in the surveyed region is quite uniform. During sideslip maneuvers, localized flow distortions impinge on the test region. Aircraft sideslip does not produce a uniform sidewash over the test region. At speeds faster than Mach 1.5, variable-pressure distortions were observed in the test region. Boundary-layer thickness on the flat plate at the rake was less than 2.1 in. For future experiments, a more focused and detailed flow-field survey than this one would be desirable.

  13. Additional field verification of convective scaling for the lateral dispersion parameter

    SciTech Connect

    Sakiyama, S.K.; Davis, P.A.

    1988-07-01

    The results of a series of diffusion trials over the heterogeneous surface of the Canadian Precambrian Shield provide additional support for the convective scaling of the lateral dispersion parameter. The data indicate that under convective conditions, the lateral dispersion parameter can be scaled with the convective velocity scale and the mixing depth. 10 references.

  14. Design and field testing of a Savonius windpump in Kenya

    SciTech Connect

    Smalera, A.; Kammen, D.M.

    1995-12-31

    One important means of improving water availability and reducing disease exposure from polluted or stagnant sources involves the design and diffusion of inexpensive and reliable water pumps. Modernized versions of the decades-old Savonius vertical axis windmill present one technology that can play an important role in this effort. To be successful, these systems must be tailored to exploit the local wind and hydrological resources, constructed and managed locally, and inexpensive to operate and maintain. We report here on our design efforts and cooperative field research with several Kenyan development organizations. Performance tests from 10-15 meter deep water pumping applications at two field sites are presented, as well as preliminary results of an analysis of the steps involved in disseminating such technology. Our research suggests that the combination of reliability and performance offered by the Savonius design make it a useful resource for community managed energy initiatives, particularly in developing nation settings.

  15. Detailed field test of yaw-based wake steering

    NASA Astrophysics Data System (ADS)

    Fleming, P.; Churchfield, M.; Scholbrock, A.; Clifton, A.; Schreck, S.; Johnson, K.; Wright, A.; Gebraad, P.; Annoni, J.; Naughton, B.; Berg, J.; Herges, T.; White, J.; Mikkelsen, T.; Sjöholm, M.; Angelou, N.

    2016-09-01

    This paper describes a detailed field-test campaign to investigate yaw-based wake steering. In yaw-based wake steering, an upstream turbine intentionally misaligns its yaw with respect to the inflow to deflect its wake away from a downstream turbine, with the goal of increasing total power production. In the first phase, a nacelle-mounted scanning lidar was used to verify wake deflection of a misaligned turbine and calibrate wake deflection models. In the second phase, these models were used within a yaw controller to achieve a desired wake deflection. This paper details the experimental design and setup. All data collected as part of this field experiment will be archived and made available to the public via the U.S. Department of Energy's Atmosphere to Electrons Data Archive and Portal.

  16. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... before running casing; (j) Test all ROV intervention functions on your subsea BOP stack during the stump... ROV hot stabs are function tested and are capable of actuating, at a minimum, one set of pipe rams...

  17. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... casing; (j) Test all ROV intervention functions on your subsea BOP stack during the stump test. You must... procedures with your APD or APM for District Manager approval. You must: (1) ensure that the ROV hot...

  18. Preliminary operational results of the industrial process heat field tests

    SciTech Connect

    Kutscher, C.; Davenport, R.

    1980-04-01

    There are currently six DOE-funded solar industrial process heat (IPH) field tests which have been operational for one year or longer. These are all low temperature first generation projects which supply heat at temperatures below 100/sup 0/C - three hot water and three hot air. During the 1979 calendar year, personnel from the Solar Energy Research Institute (SERI) visited all of these sites; the performance and cost results obtained for each project and the operational problems encountered at each site are discussed.

  19. Field Testing of Utility Robots for Lunar Surface Operations

    NASA Technical Reports Server (NTRS)

    Fong, Terrence; Bualat, Maria; Deans, Matt; Allan, Mark; Bouyssounouse, Xavier; Broxton, Michael; Edwards, Laurence; Lee, Pascal; Lee, Susan Y.; Lees, David; Park, Eric; Pedersen, Liam; Smith, Trey; To, Vinh; Utz, Hans; Pacis, Estrellina; Schreckenghost, Debra

    2008-01-01

    Since 2004, NASA has been working to return to the Moon. In contrast to the Apollo missions, two key objectives of the current exploration program is to establish significant infrastructure and an outpost. Achieving these objectives will enable long-duration stays and long-distance exploration of the Moon. To do this, robotic systems will be needed to perform tasks which cannot, or should not, be performed by crew alone. In this paper, we summarize our work to develop "utility robots" for lunar surface operations, present results and lessons learned from field testing, and discuss directions for future research.

  20. Operation and design of selected industrial process heat field tests

    SciTech Connect

    Kearney, D. W.

    1981-02-01

    The DOE program of solar industrial process heat field tests has shown solar energy to be compatible with numerous industrial needs. Both the operational projects and the detailed designs of systems that are not yet operational have resulted in valuable insights into design and hardware practice. Typical of these insights are the experiences discussed for the four projects reviewed. Future solar IPH systems should benefit greatly not only from the availability of present information, but also from the wealth of operating experience from projects due to start up in 1981.

  1. Modeling of a Parabolic Trough Solar Field for Acceptance Testing: A Case Study

    SciTech Connect

    Wagner, M. J.; Mehos, M. S.; Kearney, D. W.; McMahan, A. C.

    2011-01-01

    As deployment of parabolic trough concentrating solar power (CSP) systems ramps up, the need for reliable and robust performance acceptance test guidelines for the solar field is also amplified. Project owners and/or EPC contractors often require extensive solar field performance testing as part of the plant commissioning process in order to ensure that actual solar field performance satisfies both technical specifications and performance guaranties between the involved parties. Performance test code work is currently underway at the National Renewable Energy Laboratory (NREL) in collaboration with the SolarPACES Task-I activity, and within the ASME PTC-52 committee. One important aspect of acceptance testing is the selection of a robust technology performance model. NREL1 has developed a detailed parabolic trough performance model within the SAM software tool. This model is capable of predicting solar field, sub-system, and component performance. It has further been modified for this work to support calculation at subhourly time steps. This paper presents the methodology and results of a case study comparing actual performance data for a parabolic trough solar field to the predicted results using the modified SAM trough model. Due to data limitations, the methodology is applied to a single collector loop, though it applies to larger subfields and entire solar fields. Special consideration is provided for the model formulation, improvements to the model formulation based on comparison with the collected data, and uncertainty associated with the measured data. Additionally, this paper identifies modeling considerations that are of particular importance in the solar field acceptance testing process and uses the model to provide preliminary recommendations regarding acceptable steady-state testing conditions at the single-loop level.

  2. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... all ROV intervention functions on your subsea BOP stack during the stump test. Each ROV must be fully compatible with the BOP stack ROV intervention panels. You must also test and verify closure of at least one set of rams during the initial test on the seafloor through an ROV hot stab. You must submit...

  3. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... all ROV intervention functions on your subsea BOP stack during the stump test. Each ROV must be fully compatible with the BOP stack ROV intervention panels. You must also test and verify closure of at least one set of rams during the initial test on the seafloor through an ROV hot stab. You must submit...

  4. Thiopeptin, a New Feed-Additive Antibiotic: Biological Studies and Field Trials

    PubMed Central

    Mine, K.; Miyairi, N.; Takano, N.; Mori, S.; Watanabe, N.

    1972-01-01

    Thiopeptin is a new antibiotic, produced by Streptomyces tateyamensis and developed solely for animal use as a feed additive. The antibiotic content in animal tissue and feed was assayed in terms of the antimicrobial activity against Mycoplasma laidlawii A. This antibiotic was found to be relatively nontoxic in rats and mice. In chickens, this antibiotic is excreted into feces within 48 hr of administration and is not absorbed in tissue. It is well tolerated in both broilers and swine and is highly stable in animal feed. Thiopeptin-supplemented feed contributes to the improvement of weight gain, feed efficiency in chickens and swine, and the egg performance in layers. Thus, thiopeptin, when used as a feed additive, is quite suitable for supplementing animal nutrition. PMID:4680812

  5. An Approach to the Classification of Potential Reserve Additions of Giant Oil Fields of the World

    USGS Publications Warehouse

    Klett, T.R.; Tennyson, M.E.

    2008-01-01

    This report contains slides and notes for slides for a presentation given to the Committee on Sustainable Energy and the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology on 17 October 2007 in Geneva, Switzerland. The presentation describes the U.S. Geological Survey study to characterize and quantify petroleum-reserve additions, and the application of this study to help classify the quantities.

  6. Synergistic interactions between commonly used food additives in a developmental neurotoxicity test.

    PubMed

    Lau, Karen; McLean, W Graham; Williams, Dominic P; Howard, C Vyvyan

    2006-03-01

    Exposure to non-nutritional food additives during the critical development window has been implicated in the induction and severity of behavioral disorders such as attention deficit hyperactivity disorder (ADHD). Although the use of single food additives at their regulated concentrations is believed to be relatively safe in terms of neuronal development, their combined effects remain unclear. We therefore examined the neurotoxic effects of four common food additives in combinations of two (Brilliant Blue and L-glutamic acid, Quinoline Yellow and aspartame) to assess potential interactions. Mouse NB2a neuroblastoma cells were induced to differentiate and grow neurites in the presence of additives. After 24 h, cells were fixed and stained and neurite length measured by light microscopy with computerized image analysis. Neurotoxicity was measured as an inhibition of neurite outgrowth. Two independent models were used to analyze combination effects: effect additivity and dose additivity. Significant synergy was observed between combinations of Brilliant Blue with L-glutamic acid, and Quinoline Yellow with aspartame, in both models. Involvement of N-methyl-D-aspartate (NMDA) receptors in food additive-induced neurite inhibition was assessed with a NMDA antagonist, CNS-1102. L-glutamic acid- and aspartame-induced neurotoxicity was reduced in the presence of CNS-1102; however, the antagonist did not prevent food color-induced neurotoxicity. Theoretical exposure to additives was calculated based on analysis of content in foodstuff, and estimated percentage absorption from the gut. Inhibition of neurite outgrowth was found at concentrations of additives theoretically achievable in plasma by ingestion of a typical snack and drink. In addition, Trypan Blue dye exclusion was used to evaluate the cellular toxicity of food additives on cell viability of NB2a cells; both combinations had a straightforward additive effect on cytotoxicity. These data have implications for the

  7. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., DEPARTMENT OF EDUCATION DISABILITY AND REHABILITATION RESEARCH PROJECTS AND CENTERS PROGRAM How Does the... 34 Education 2 2013-07-01 2013-07-01 false What are the additional considerations for selecting Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of...

  8. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., DEPARTMENT OF EDUCATION DISABILITY AND REHABILITATION RESEARCH PROJECTS AND CENTERS PROGRAM How Does the... 34 Education 2 2014-07-01 2013-07-01 true What are the additional considerations for selecting Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of...

  9. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., DEPARTMENT OF EDUCATION DISABILITY AND REHABILITATION RESEARCH PROJECTS AND CENTERS PROGRAM How Does the... 34 Education 2 2011-07-01 2010-07-01 true What are the additional considerations for selecting Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of...

  10. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., DEPARTMENT OF EDUCATION DISABILITY AND REHABILITATION RESEARCH PROJECTS AND CENTERS PROGRAM How Does the... 34 Education 2 2012-07-01 2012-07-01 false What are the additional considerations for selecting Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of...

  11. A near-infrared spectroscopic study of young field ultracool dwarfs: additional analysis

    NASA Astrophysics Data System (ADS)

    Allers, K. N.; Liu, M. C.

    We present additional analysis of the classification system presented in \\citet{allers13}. We refer the reader to \\citet{allers13} for a detailed discussion of our near-IR spectral type and gravity classification system. Here, we address questions and comments from participants of the Brown Dwarfs Come of Age meeting. In particular, we examine the effects of binarity and metallicity on our classification system. We also present our classification of Pleiades brown dwarfs using published spectra. Lastly, we determine SpTs and calculate gravity-sensitive indices for the BT-Settl atmospheric models and compare them to observations.

  12. Comprehensive visual field test & diagnosis system in support of astronaut health and performance

    NASA Astrophysics Data System (ADS)

    Fink, Wolfgang; Clark, Jonathan B.; Reisman, Garrett E.; Tarbell, Mark A.

    Long duration spaceflight, permanent human presence on the Moon, and future human missions to Mars will require autonomous medical care to address both expected and unexpected risks. An integrated non-invasive visual field test & diagnosis system is presented for the identification, characterization, and automated classification of visual field defects caused by the spaceflight environment. This system will support the onboard medical provider and astronauts on space missions with an innovative, non-invasive, accurate, sensitive, and fast visual field test. It includes a database for examination data, and a software package for automated visual field analysis and diagnosis. The system will be used to detect and diagnose conditions affecting the visual field, while in space and on Earth, permitting the timely application of therapeutic countermeasures before astronaut health or performance are impaired. State-of-the-art perimetry devices are bulky, thereby precluding application in a spaceflight setting. In contrast, the visual field test & diagnosis system requires only a touchscreen-equipped computer or touchpad device, which may already be in use for other purposes (i.e., no additional payload), and custom software. The system has application in routine astronaut assessment (Clinical Status Exam), pre-, in-, and post-flight monitoring, and astronaut selection. It is deployable in operational space environments, such as aboard the International Space Station or during future missions to or permanent presence on the Moon and Mars.

  13. Additional road markings as an indication of speed limits: results of a field experiment and a driving simulator study.

    PubMed

    Daniels, Stijn; Vanrie, Jan; Dreesen, An; Brijs, Tom

    2010-05-01

    Although speed limits are indicated by road signs, road users are not always aware, while driving, of the actual speed limit on a given road segment. The Roads and Traffic Agency developed additional road markings in order to support driver decisions on speed on 70 km/h roads in Flanders-Belgium. In this paper the results are presented of two evaluation studies, both a field study and a simulator study, on the effects of the additional road markings on speed behaviour. The results of the field study showed no substantial effect of the markings on speed behaviour. Neither did the simulator study, with slightly different stimuli. Nevertheless an effect on lateral position was noticed in the simulator study, showing at least some effect of the markings. The role of conspicuity of design elements and expectations towards traffic environments is discussed. Both studies illustrate well some strengths and weaknesses of observational field studies compared to experimental simulator studies.

  14. Pricetown I underground coal gasification field test: operations report

    SciTech Connect

    Agarwal, A.K.; Seabaugh, P.W.; Zielinski, R.E.

    1981-01-01

    An Underground Coal Gasification (UCG) field test in bituminous coal was successfully completed near Pricetown, West Virginia. The primary objective of this field test was to determine the viability of the linked vertical well (LVV) technology to recover the 900 foot deep, 6 foot thick coal seam. A methane rich product gas with an average heating value of approximately 250 Btu/SCF was produced at low air injection flow rates during the reverse combustion linkage phase. Heating value of the gas produced during the linkage enhancement phase was 221 Btu/SCF with air injection. The high methane formation has been attributed to the thermal and hydrocracking of tars and oils along with hydropyrolysis and hydrogasification of coal char. The high heating value of the gas was the combined effect of residence time, flow pattern, injection flow rate, injection pressure, and back pressure. During the gasification phase, a gas with an average heating value of 125 Btu/SCF was produced with only air injection, which resulted in an average energy production of 362 MMBtu/day.

  15. Field Testing of Nano-PCM Enhanced Building Envelope Components

    SciTech Connect

    Biswas, Kaushik; Childs, Phillip W; Atchley, Jerald Allen

    2013-08-01

    The U.S. Department of Energy s (DOE) Building Technologies Program s goal of developing high-performance, energy efficient buildings will require more cost-effective, durable, energy efficient building envelopes. Forty-eight percent of the residential end-use energy consumption is spent on space heating and air conditioning. Reducing envelope-generated heating and cooling loads through application of phase change material (PCM)-enhanced envelope components can facilitate maximizing the energy efficiency of buildings. Field-testing of prototype envelope components is an important step in estimating their energy benefits. An innovative phase change material (nano-PCM) was developed with PCM encapsulated with expanded graphite (interconnected) nanosheets, which is highly conducive for enhanced thermal storage and energy distribution, and is shape-stable for convenient incorporation into lightweight building components. During 2012, two test walls with cellulose cavity insulation and prototype PCM-enhanced interior wallboards were installed in a natural exposure test (NET) facility at Charleston, SC. The first test wall was divided into four sections, which were separated by wood studs and thin layers of foam insulation. Two sections contained nano-PCM-enhanced wallboards: one was a three-layer structure, in which nano-PCM was sandwiched between two gypsum boards, and the other one had PCM dispersed homogeneously throughout graphite nanosheets-enhanced gypsum board. The second test wall also contained two sections with interior PCM wallboards; one contained nano-PCM dispersed homogeneously in gypsum and the other was gypsum board containing a commercial microencapsulated PCM (MEPCM) for comparison. Each test wall contained a section covered with gypsum board on the interior side, which served as control or a baseline for evaluation of the PCM wallboards. The walls were instrumented with arrays of thermocouples and heat flux transducers. Further, numerical modeling of

  16. Patch testing discordance alert: false-negative findings with rubber additives and fragrances.

    PubMed

    Sherertz, E F; Fransway, A F; Belsito, D V; DeLeo, V A; Fowler, J F; Maibach, H I; Marks, J G; Mathias, C G; Pratt, M D; Rietschel, R L; Taylor, J S

    2001-08-01

    From July 1996 through June 1998, the North American Contact Dermatitis Group evaluated 318 patients for suspected contact dermatitis by patch testing simultaneously with Finn Chambers and the T.R.U.E. Test allergen system. Discrepancies between the two systems were found in some of the results, particularly with fragrance and rubber allergens. These results suggest that positive reactions to fragrance, thiuram, and carba mix allergens may be missed if the T.R.U.E. Test is used alone.

  17. Laboratory and field assessment of arsenic testing field kits in Bangladesh and West Bengal, India.

    PubMed

    Pande, S P; Deshpande, L S; Kaul, S N

    2001-04-01

    High concentrations of arsenic in ground waters in West Bengal and Bangladesh have become a major cause for concern in recent years. Given the enormity and the severity of the problem of arsenic poisoning, a task of evaluating the commercially available arsenic detection field kits for their capabilities was undertaken. In the light of the findings, generic specifications were recommended which could form the basis for indigenous manufacture of these kits in the arsenic affected countries. This article presents the results of the laboratory and field evaluation conducted in Bangladesh and West Bengal of five arsenic testing field kits. The salient features of the kits, their merits and limitations have been brought out. Based on the criteria of kit design, quality of chemicals used, colour comparator charts, detection range, time required for analysis, cost etc., a comparative ranking of the kits has been made to facilitate the choice of the kit to meet specific requirements.

  18. Direct-field acoustic testing of a flight system : logistics, challenges, and results.

    SciTech Connect

    Stasiunas, Eric Carl; Gurule, David Joseph; Babuska, Vit; Skousen, Troy J.

    2010-10-01

    Before a spacecraft can be considered for launch, it must first survive environmental testing that simulates the launch environment. Typically, these simulations include vibration testing performed using an electro-dynamic shaker. For some spacecraft however, acoustic excitation may provide a more severe loading environment than base shaker excitation. Because this was the case for a Sandia Flight System, it was necessary to perform an acoustic test prior to launch in order to verify survival due to an acoustic environment. Typically, acoustic tests are performed in acoustic chambers, but because of scheduling, transportation, and cleanliness concerns, this was not possible. Instead, the test was performed as a direct field acoustic test (DFAT). This type of test consists of surrounding a test article with a wall of speakers and controlling the acoustic input using control microphones placed around the test item, with a closed-loop control system. Obtaining the desired acoustic input environment - proto-flight random noise input with an overall sound pressure level (OASPL) of 146.7 dB-with this technique presented a challenge due to several factors. An acoustic profile with this high OASPL had not knowingly been obtained using the DFAT technique prior to this test. In addition, the test was performed in a high-bay, where floor space and existing equipment constrained the speaker circle diameter. And finally, the Flight System had to be tested without contamination of the unit, which required a contamination bag enclosure of the test unit. This paper describes in detail the logistics, challenges, and results encountered while performing a high-OASPL, direct-field acoustic test on a contamination-sensitive Flight System in a high-bay environment.

  19. A field test of threat sensitivity in a marine gastropod

    PubMed

    Rochette; Dill; Himmelman

    1997-11-01

    In the Mingan Islands, the whelk Buccinum undatum displays defensive manoeuvres to both contact and water-borne chemical cues from the predatory asteroid Leptasterias polarisIn spite of this, whelks occasionally aggregate in great numbers near L. polaris while it is ingesting a prey; they then attempt to steal food from their predator and also wait for leftovers. In this study, the response of whelks in different types of encounters with L. polaris was examined to test the hypothesis that whelks are sensitive to the magnitude of the threat their predator represents. In a field experiment, whelks consistently fled both non-feeding and feeding L. polaris (asteroids used were consuming small prey items that were unlikely to provide food for whelks). When current flow was stable, whelks fled more directly down current and more frequently displayed violent defensive behaviours, in response to non-feeding L. polariswhich presented a higher risk, than in response to feeding asteroids (lower risk; 47% versus 2%). Consequently, whelks tested with non-feeding asteroids more rapidly distanced themselves from the predators than did whelks tested with feeding asteroids. In a field survey, there were more active whelks in the vicinity of cruising (higher risk) than stationary (lower risk) L. polaris (53% versus 14%). Among those whelks that were active, defensive behaviour patterns such as shell rocking and leaping escape movements were frequently shown by whelks near cruising predators (69%), but never by whelks near stationary predators (0%). The discriminative capabilities apparent in these results are likely to be adaptive, because they enable whelks to limit the cost of escape responses while still keeping predation risk low, and also because they facilitate a close association with L. polaris from which the whelks receive feeding benefits.Copyright 1997 The Association for the Study of Animal Behaviour1997The Association for the Study of Animal Behaviour PMID:9398362

  20. A field test of threat sensitivity in a marine gastropod

    PubMed

    Rochette; Dill; Himmelman

    1997-11-01

    In the Mingan Islands, the whelk Buccinum undatum displays defensive manoeuvres to both contact and water-borne chemical cues from the predatory asteroid Leptasterias polarisIn spite of this, whelks occasionally aggregate in great numbers near L. polaris while it is ingesting a prey; they then attempt to steal food from their predator and also wait for leftovers. In this study, the response of whelks in different types of encounters with L. polaris was examined to test the hypothesis that whelks are sensitive to the magnitude of the threat their predator represents. In a field experiment, whelks consistently fled both non-feeding and feeding L. polaris (asteroids used were consuming small prey items that were unlikely to provide food for whelks). When current flow was stable, whelks fled more directly down current and more frequently displayed violent defensive behaviours, in response to non-feeding L. polariswhich presented a higher risk, than in response to feeding asteroids (lower risk; 47% versus 2%). Consequently, whelks tested with non-feeding asteroids more rapidly distanced themselves from the predators than did whelks tested with feeding asteroids. In a field survey, there were more active whelks in the vicinity of cruising (higher risk) than stationary (lower risk) L. polaris (53% versus 14%). Among those whelks that were active, defensive behaviour patterns such as shell rocking and leaping escape movements were frequently shown by whelks near cruising predators (69%), but never by whelks near stationary predators (0%). The discriminative capabilities apparent in these results are likely to be adaptive, because they enable whelks to limit the cost of escape responses while still keeping predation risk low, and also because they facilitate a close association with L. polaris from which the whelks receive feeding benefits.Copyright 1997 The Association for the Study of Animal Behaviour1997The Association for the Study of Animal Behaviour

  1. The Field Lysimeter Test Facility (FLTF) at the Hanford Site: Installation and initial tests

    SciTech Connect

    Gee, G.W.; Kirkham, R.R.; Downs, J.L.; Campbell, M.D.

    1989-02-01

    The objectives of this program are to test barrier design concepts and to demonstrate a barrier design that meets established performance criteria for use in isolating wastes disposed of near-surface at the Hanford Site. Specifically, the program is designed to assess how well the barriers perform in controlling biointrusion, water infiltration, and erosion, as well as evaluating interactions between environmental variables and design factors of the barriers. To assess barrier performance and design with respect to infiltration control, field lysimeters and small- and large-scale field plots are planned to test the performance of specific barrier designs under actual and modified (enhanced precipitation) climatic conditions. The Field Lysimeter Test Facility (FLTF) is located in the 600 Area of the Hanford Site just east of the 200 West Area and adjacent to the Hanford Meteorological Station. The FLTF data will be used to assess the effectiveness of selected protective barrier configurations in controlling water infiltration. The facility consists of 14 drainage lysimeters (2 m dia x 3 m deep) and four precision weighing lysimeters (1.5 m x 1.5 m x 1.7 m deep). The lysimeters are buried at grade and aligned in a parallel configuration, with nine lysimeters on each side of an underground instrument chamber. The lysimeters were filled with materials to simulate a multilayer protective barrier system. Data gathered from the FLTF will be used to compare key barrier components and to calibrate and test models for predicting long-term barrier performance.

  2. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests and... for small carpets and rugs subject to FF 2-70 shall be subject to all of the requirements of § 1631.31... warranties for small carpets and rugs subject to FF 2-70 shall perform tests and maintain records on...

  3. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests and... for small carpets and rugs subject to FF 2-70 shall be subject to all of the requirements of § 1631.31... warranties for small carpets and rugs subject to FF 2-70 shall perform tests and maintain records on...

  4. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests and... for small carpets and rugs subject to FF 2-70 shall be subject to all of the requirements of § 1631.31... warranties for small carpets and rugs subject to FF 2-70 shall perform tests and maintain records on...

  5. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests and... for small carpets and rugs subject to FF 2-70 shall be subject to all of the requirements of § 1631.31... warranties for small carpets and rugs subject to FF 2-70 shall perform tests and maintain records on...

  6. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests and... for small carpets and rugs subject to FF 2-70 shall be subject to all of the requirements of § 1631.31... warranties for small carpets and rugs subject to FF 2-70 shall perform tests and maintain records on...

  7. Field tests prove microscale NRU to upgrade low-btu gas

    USGS Publications Warehouse

    Bhattacharya, S.; David, Newell K.; Lynn, Watney W.; Sigel, M.

    2009-01-01

    The Kansas Geological Survey (University of Kansas) and the American Energies Corp., Wichita, have conducted field tests of a scalable, microscale, N2-rejection unit (NRU) to demonstrate its effectiveness to upgrade low-pressure ((<100 psig) and low-volume (=100 Mcfd) low-btu gas to pipeline quality. The tests aim to develop inexpensive NRU technology, which is designed for low- volume, low-pressure gas wells, to significantly increase the contribution of marginal low-btu gas to the gas supply of the US. The NRU uses two towers and uses three stages, namely, adsorption under pressure, venting to 2 psig, and desorption under vacuum. The modular design allows additional sets of towers to be added or removed to handle increases or decreases in feed volumes. The field tests also reveal that a strong compressor, which is capable of evacuating the tower (volume) as quickly as possible, should be employed to reduce process cycle time and increase plant throughput.

  8. MIXTURES OF THYROID DISRUPTING CHEMICALS: TESTING ADDITIVITY OF HEPATIC INDUCERS AND THYROID PEROXIDASE INHIBITORS.

    EPA Science Inventory

    Humans are exposed to chemical mixtures via diet, occupation, and the environment. Previous data demonstrated that low doses of polycyclic halogenated aromatic hydrocarbons (PHAHs) acting through similar mechanisms result in an additive reduction of thyroxine (T4). If xenobioti...

  9. Cooperative field test program for wind systems. Final report

    SciTech Connect

    Bollmeier, W.S. II; Dodge, D.M.

    1992-03-01

    The objectives of the Federal Wind Energy Program, managed by the US Department of Energy (DOE), are (1) to assist industry and utilities in achieving a multi-regional US market penetration of wind systems, and (2) to establish the United States as the world leader in the development of advanced wind turbine technology. In 1984, the program conducted a series of planning workshops with representatives from the wind energy industry to obtain input on the Five-Year Research Plan then being prepared by DOE. One specific suggestion that came out of these meetings was that the federal program should conduct cooperative research tests with industry to enhance the technology transfer process. It was also felt that the active involvement of industry in DOE-funded research would improve the state of the art of wind turbine technology. DOE established the Cooperative Field Test Program (CFTP) in response to that suggestion. This program was one of the first in DOE to feature joint industry-government research test teams working toward common objectives.

  10. Design and Field Test of a Galvanometer Deflected Streak Camera

    SciTech Connect

    Lai, C C; Goosman, D R; Wade, J T; Avara, R

    2002-11-08

    We have developed a compact fieldable optically-deflected streak camera first reported in the 20th HSPP Congress. Using a triggerable galvanometer that scans the optical signal, the imaging and streaking function is an all-optical process without incurring any photon-electron-photon conversion or photoelectronic deflection. As such, the achievable imaging quality is limited mainly only by optical design, rather than by multiple conversions of signal carrier and high voltage electron-optics effect. All core elements of the camera are packaged into a 12 inch x 24 inch footprint box, a size similar to that of a conventional electronic streak camera. At LLNL's Site-300 Test Site, we have conducted a Fabry-Perot interferometer measurement of fast object velocity using this all-optical camera side-by-side with an intensified electronic streak camera. These two cameras are configured as two independent instruments for recording synchronously each branch of the 50/50 splits from one incoming signal. Given the same signal characteristics, the test result has undisputedly demonstrated superior imaging performance for the all-optical streak camera. It produces higher signal sensitivity, wider linear dynamic range, better spatial contrast, finer temporal resolution, and larger data capacity as compared with that of the electronic counterpart. The camera had also demonstrated its structural robustness and functional consistence to be well compatible with field environment. This paper presents the camera design and the test results in both pictorial records and post-process graphic summaries.

  11. Testing for Additivity in Chemical Mixtures Using a Fixed-Ratio Ray Design and Statistical Equivalence Testing Methods

    EPA Science Inventory

    Fixed-ratio ray designs have been used for detecting and characterizing interactions of large numbers of chemicals in combination. Single chemical dose-response data are used to predict an “additivity curve” along an environmentally relevant ray. A “mixture curve” is estimated fr...

  12. CHARMM additive all-atom force field for carbohydrate derivatives and its utility in polysaccharide and carbohydrate-protein modeling

    PubMed Central

    Guvench, Olgun; Mallajosyula, Sairam S.; Raman, E. Prabhu; Hatcher, Elizabeth; Vanommeslaeghe, Kenno; Foster, Theresa J.; Jamison, Francis W.; MacKerell, Alexander D.

    2011-01-01

    Monosaccharide derivatives such as xylose, fucose, N-acetylglucosamine (GlcNAc), N-acetylgalactosamine (GlaNAc), glucuronic acid, iduronic acid, and N-acetylneuraminic acid (Neu5Ac) are important components of eukaryotic glycans. The present work details development of force-field parameters for these monosaccharides and their covalent connections to proteins via O-linkages to serine or threonine sidechains and via N-linkages to asparagine sidechains. The force field development protocol was designed to explicitly yield parameters that are compatible with the existing CHARMM additive force field for proteins, nucleic acids, lipids, carbohydrates, and small molecules. Therefore, when combined with previously developed parameters for pyranose and furanose monosaccharides, for glycosidic linkages between monosaccharides, and for proteins, the present set of parameters enables the molecular simulation of a wide variety of biologically-important molecules such as complex carbohydrates and glycoproteins. Parametrization included fitting to quantum mechanical (QM) geometries and conformational energies of model compounds, as well as to QM pair interaction energies and distances of model compounds with water. Parameters were validated in the context of crystals of relevant monosaccharides, as well NMR and/or x-ray crystallographic data on larger systems including oligomeric hyaluronan, sialyl Lewis X, O- and N-linked glycopeptides, and a lectin:sucrose complex. As the validated parameters are an extension of the CHARMM all-atom additive biomolecular force field, they further broaden the types of heterogeneous systems accessible with a consistently-developed force-field model. PMID:22125473

  13. Field Evidence for Co-Metabolism of Trichloroethene Stimulated by Addition of Electron Donor to Groundwater

    SciTech Connect

    Conrad, Mark E.; Brodie, Eoin L.; Radtke, Corey W.; Bill, Markus; Delwiche, Mark E.; Lee, M. Hope; Swift, Dana L.; Colwell, Frederick S.

    2010-05-17

    For more than 10 years, electron donor has been injected into the Snake River aquifer beneath the Test Area North site of the Idaho National Laboratory for the purpose of stimulating microbial reductive dechlorination of trichloroethene (TCE) in groundwater. This has resulted in significant TCE removal from the source area of the contaminant plume and elevated dissolved CH4 in the groundwater extending 250 m from the injection well. The delta13C of the CH4 increases from 56o/oo in the source area to -13 o/oo with distance from the injection well, whereas the delta13C of dissolved inorganic carbon decreases from 8 o/oo to -13 o/oo, indicating a shift from methanogenesis to methane oxidation. This change in microbial activity along the plume axis is confirmed by PhyloChip microarray analyses of 16S rRNA genes obtained from groundwater microbial communities, which indicate decreasing abundances of reductive dechlorinating microorganisms (e.g., Dehalococcoides ethenogenes) and increasing CH4-oxidizing microorganisms capable of aerobic co-metabolism of TCE (e.g., Methylosinus trichosporium). Incubation experiments with 13C-labeled TCE introduced into microcosms containing basalt and groundwater from the aquifer confirm that TCE co-metabolism is possible. The results of these studies indicate that electron donor amendment designed to stimulate reductive dechlorination of TCE may also stimulate co-metabolism of TCE.

  14. Field evidence for co-metabolism of trichloroethene stimulated by addition of electron donor to groundwater.

    PubMed

    Conrad, Mark E; Brodie, Eoin L; Radtke, Corey W; Bill, Markus; Delwiche, Mark E; Lee, M Hope; Swift, Dana L; Colwell, Frederick S

    2010-06-15

    For more than 10 years, electron donor has been injected into the Snake River aquifer beneath the Test Area North site of the Idaho National Laboratory for the purpose of stimulating microbial reductive dechlorination of trichloroethene (TCE) in groundwater. This has resulted in significant TCE removal from the source area of the contaminant plume and elevated dissolved CH(4) in the groundwater extending 250 m from the injection well. The delta(13)C of the CH(4) increases from -56 per thousand in the source area to -13 per thousand with distance from the injection well, whereas the delta(13)C of dissolved inorganic carbon decreases from 8 per thousand to -13 per thousand, indicating a shift from methanogenesis to methane oxidation. This change in microbial activity along the plume axis is confirmed by PhyloChip microarray analyses of 16S rRNA genes obtained from groundwater microbial communities, which indicate decreasing abundances of reductive dechlorinating microorganisms (e.g., Dehalococcoides ethenogenes) and increasing CH(4)-oxidizing microorganisms capable of aerobic co-metabolism of TCE (e.g., Methylosinus trichosporium). Incubation experiments with (13)C-labeled TCE introduced into microcosms containing basalt and groundwater from the aquifer confirm that TCE co-metabolism is possible. The results of these studies indicate that electron donor amendment designed to stimulate reductive dechlorination of TCE may also stimulate co-metabolism of TCE. PMID:20476753

  15. Advanced technology ladle preheater research, development, field test and commercialization program. Annual report

    SciTech Connect

    Smith, D.B.; Nelson, J.; Battles, D.D.

    1981-01-01

    The objective of this project is to develop a cost effective, reliable heating system that will improve gas utilization efficiencies. The Phase I prototype THERMECON (tm) Ladle Heater System was successfully designed, fabricated, and field tested during the year. Extensive baseline performance testing of the prototype THERMECON system versus a conventional horizontally positioned ladle heater system was completed. The prototype THERMECON system heated the ladle faster, hotter, and with less energy than the conventional heaters, in addition to other improved performance factors. The temperature uniformity of the refractory surface heated by the THERMECON system was much improved over typical conventional systems.

  16. Design and test of field programmable gate arrays in space applications

    NASA Technical Reports Server (NTRS)

    Mckerracher, Priscilla L.; Cain, Russel P.; Barnett, Jon C.; Green, William S.; Kinnison, James D.

    1992-01-01

    Field Programmable Gate Arrays (FPGAU's) offer substantial benefits in terms of flexibility and design integration. In addition to qualifying this device for space applications by establishing its reliability and evaluating its sensitivity to radiation, screening the programmed devices with Automatic Test Equipment (ATE) and functional burn-in presents an interesting challenge. This paper presents a review of the design, qualification, and screening cycle employed for FPGA designs in a space program, and demonstrates the need for close interaction between design and test engineers.

  17. Multiple testing for neuroimaging via hidden Markov random field.

    PubMed

    Shu, Hai; Nan, Bin; Koeppe, Robert

    2015-09-01

    Traditional voxel-level multiple testing procedures in neuroimaging, mostly p-value based, often ignore the spatial correlations among neighboring voxels and thus suffer from substantial loss of power. We extend the local-significance-index based procedure originally developed for the hidden Markov chain models, which aims to minimize the false nondiscovery rate subject to a constraint on the false discovery rate, to three-dimensional neuroimaging data using a hidden Markov random field model. A generalized expectation-maximization algorithm for maximizing the penalized likelihood is proposed for estimating the model parameters. Extensive simulations show that the proposed approach is more powerful than conventional false discovery rate procedures. We apply the method to the comparison between mild cognitive impairment, a disease status with increased risk of developing Alzheimer's or another dementia, and normal controls in the FDG-PET imaging study of the Alzheimer's Disease Neuroimaging Initiative.

  18. Field Tested Service Oriented Robotic Architecture: Case Study

    NASA Technical Reports Server (NTRS)

    Flueckiger, Lorenzo; Utz, Hanz

    2012-01-01

    This paper presents the lessons learned from six years of experiments with planetary rover prototypes running the Service Oriented Robotic Architecture (SORA) developed by the Intelligent Robotics Group (IRG) at NASA Ames Research Center. SORA relies on proven software methods and technologies applied to the robotic world. Based on a Service Oriented Architecture and robust middleware, SORA extends its reach beyond the on-board robot controller and supports the full suite of software tools used during mission scenarios from ground control to remote robotic sites. SORA has been field tested in numerous scenarios of robotic lunar and planetary exploration. The results of these high fidelity experiments are illustrated through concrete examples that have shown the benefits of using SORA as well as its limitations.

  19. Multiple testing for neuroimaging via hidden Markov random field.

    PubMed

    Shu, Hai; Nan, Bin; Koeppe, Robert

    2015-09-01

    Traditional voxel-level multiple testing procedures in neuroimaging, mostly p-value based, often ignore the spatial correlations among neighboring voxels and thus suffer from substantial loss of power. We extend the local-significance-index based procedure originally developed for the hidden Markov chain models, which aims to minimize the false nondiscovery rate subject to a constraint on the false discovery rate, to three-dimensional neuroimaging data using a hidden Markov random field model. A generalized expectation-maximization algorithm for maximizing the penalized likelihood is proposed for estimating the model parameters. Extensive simulations show that the proposed approach is more powerful than conventional false discovery rate procedures. We apply the method to the comparison between mild cognitive impairment, a disease status with increased risk of developing Alzheimer's or another dementia, and normal controls in the FDG-PET imaging study of the Alzheimer's Disease Neuroimaging Initiative. PMID:26012881

  20. New challenge of field testing dense WDM systems

    NASA Astrophysics Data System (ADS)

    Mason, Lynn

    1998-09-01

    Dense wavelength-division multiplexing fiber-optic techniques hold great promise as tools to address many of the challenges facing communication system operators. This new technical solution can increase the capacity of existing networks without the need for expensive re-cabling and is also an open door toward all optical network design. But the many advantages they offer come at a price: optical component properties and cable characteristics must be addressed that could safely be neglected in systems using simpler transmission techniques. The new spectral dimension brought by testing capabilities must now be provided to the field, capabilities that are usable by maintenance personnel working in conditions that are very different from those in the stable, controlled laboratory environment.

  1. A field test of a simple stochastic radiative transfer model

    SciTech Connect

    Byrne, N.

    1995-09-01

    The problem of determining the effect of clouds on the radiative energy balance of the globe is of well-recognized importance. One can in principle solve the problem for any given configuration of clouds using numerical techniques. This knowledge is not useful however, because of the amount of input data and computer resources required. Besides, we need only the average of the resulting solution over the grid scale of a general circulation model (GCM). Therefore, we are interested in estimating the average of the solutions of such fine-grained problems using only coarse grained data, a science or art called stochastic radiation transfer. Results of the described field test indicate that the stochastic description is a somewhat better fit to the data than is a fractional cloud cover model, but more data are needed. 1 ref., 3 figs.

  2. Non-contact rail flaw detection system: first field test

    NASA Astrophysics Data System (ADS)

    Rizzo, Piervincenzo; Coccia, Stefano; Lanza di Scalea, Francesco; Bartoli, Ivan; Fateh, Mahmood

    2007-04-01

    Researchers at UCSD, with the initial support of NSF and the current support of the Federal Railroad Administration (FRA), have been working on a flaw detection prototype for rails that uses non-contact ultrasonic probing and robust data processing algorithms to provide high speed and high reliability defect detection in these structures. Besides the obvious advantages of non-contact probing, the prototype uses ultrasonic guided waves able to detect and quantify transverse cracks in the rail head, notoriously the most dangerous of all rail track defects. This paper will report on the first field test which was conducted in Gettysburg, PA in March 2006 with the technical support of ENSCO, Inc. Good results were obtained for the detection of both surface-breaking and internal cracks ranging in size from 2% cross-sectional head area (H.A.) reduction to 80% H.A. reduction.

  3. Vadose Zone Transport Field Study: Detailed Test Plan for Simulated Leak Tests

    SciTech Connect

    Ward, Anderson L.; Gee, Glendon W.

    2000-06-23

    This report describes controlled transport experiments at well-instrumented field tests to be conducted during FY 2000 in support of DOE?s Vadose Zone Transport Field Study (VZTFS). The VZTFS supports the Groundwater/Vadose Zone Integration Project Science and Technology Initiative. The field tests will improve understanding of field-scale transport and lead to the development or identification of efficient and cost-effective characterization methods. These methods will capture the extent of contaminant plumes using existing steel-cased boreholes. Specific objectives are to 1) identify mechanisms controlling transport processes in soils typical of the hydrogeologic conditions of Hanford?s waste disposal sites; 2) reduce uncertainty in conceptual models; 3) develop a detailed and accurate data base of hydraulic and transport parameters for validation of three-dimensional numerical models; and 4) identify and evaluate advanced, cost-effective characterization methods with the potential to assess changing conditions in the vadose zone, particularly as surrogates of currently undetectable high-risk contaminants. Pacific Northwest National Laboratory (PNNL) manages the VZTFS for DOE.

  4. Hanford 100-D Area Biostimulation Soluble Substrate Field Test: Interim Data Summary for the Substrate Injection and Process Monitoring Phases of the Field Test

    SciTech Connect

    Truex, Michael J.; Vermeul, Vincent R.; Mackley, Rob D.; Fritz, Brad G.; Mendoza, Donaldo P.; Johnson, Christian D.; Elmore, Rebecca P.; Brockman, Fred J.; Bilskis, Christina L.

    2008-06-01

    Pacific Northwest National Laboratory is conducting a treatability test designed to demonstrate that in situ biostimulation can be applied to help meet cleanup goals in the Hanford Site 100-D Area. The in situ biostimulation technology is intended to provide supplemental treatment upgradient of the In Situ Redox Manipulation (ISRM) barrier by reducing the concentration of the primary oxidizing species in groundwater (i.e., nitrate and dissolved oxygen) and chromate, and thereby increasing the longevity of the ISRM barrier. This report summarizes the initial results from field testing of an in situ biological treatment zone implemented through injection of a soluble substrate. The field test is divided into operational phases that include substrate injection, process monitoring, and performance monitoring. The results summarized herein are for the substrate injection and process monitoring phase encompassing the first approximately three months of field testing. Performance monitoring is ongoing at the time this report was prepared and is planned to extend over approximately 18 months. As such, this report is an interim data summary report for the field test. The treatability testing has multiple objectives focused on evaluating the performance of biostimulation as a reducing barrier for nitrate, oxygen, and chromate. The following conclusions related to these objectives are supported by the data provided in this report. Substrate was successfully distributed to a radius of about 15 m (50 ft) from the injection well. Monitoring data indicate that microbial growth initiated rapidly, and this rapid growth would limit the ability to inject substrate to significantly larger zones from a single injection well. As would be expected, the uniformity of substrate distribution was impacted by subsurface heterogeneity. However, subsequent microbial activity and ability to reduce the targeted species was observed throughout the monitored zone during the process monitoring

  5. Testing neoclassical competitive market theory in the field.

    PubMed

    List, John A

    2002-11-26

    This study presents results from a pilot field experiment that tests predictions of competitive market theory. A major advantage of this particular field experimental design is that my laboratory is the marketplace: subjects are engaged in buying, selling, and trading activities whether I run an exchange experiment or am a passive observer. In this sense, I am gathering data in a natural environment while still maintaining the necessary control to execute a clean comparison between treatments. The main results of the study fall into two categories. First, the competitive model predicts reasonably well in some market treatments: the expected price and quantity levels are approximated in many market rounds. Second, the data suggest that market composition is important: buyer and seller experience levels impact not only the distribution of rents but also the overall level of rents captured. An unexpected result in this regard is that average market efficiency is lowest in markets that match experienced buyers and experienced sellers and highest when experienced buyers engage in bargaining with inexperienced sellers. Together, these results suggest that both market experience and market composition play an important role in the equilibrium discovery process.

  6. Additional Clarification of Intercollegiate Athletics Policy: Three-Part Test. Part Three

    ERIC Educational Resources Information Center

    US Department of Education, 2005

    2005-01-01

    This Additional Clarification, "User's Guide to Developing Student Interest Surveys Under Title IX" (User's Guide), and related technical report are resources to assist institutions in meeting their compliance obligations. Taken together, they serve to clarify many of the factors OCR will consider under part three, and to facilitate compliance…

  7. Testing a Gender Additive Model: The Role of Body Image in Adolescent Depression

    ERIC Educational Resources Information Center

    Bearman, Sarah Kate; Stice, Eric

    2008-01-01

    Despite consistent evidence that adolescent girls are at greater risk of developing depression than adolescent boys, risk factor models that account for this difference have been elusive. The objective of this research was to examine risk factors proposed by the "gender additive" model of depression that attempts to partially explain the increased…

  8. Large fluctuations of the macroscopic current in diffusive systems: a numerical test of the additivity principle.

    PubMed

    Hurtado, Pablo I; Garrido, Pedro L

    2010-04-01

    Most systems, when pushed out of equilibrium, respond by building up currents of locally conserved observables. Understanding how microscopic dynamics determines the averages and fluctuations of these currents is one of the main open problems in nonequilibrium statistical physics. The additivity principle is a theoretical proposal that allows to compute the current distribution in many one-dimensional nonequilibrium systems. Using simulations, we validate this conjecture in a simple and general model of energy transport, both in the presence of a temperature gradient and in canonical equilibrium. In particular, we show that the current distribution displays a Gaussian regime for small current fluctuations, as prescribed by the central limit theorem, and non-Gaussian (exponential) tails for large current deviations, obeying in all cases the Gallavotti-Cohen fluctuation theorem. In order to facilitate a given current fluctuation, the system adopts a well-defined temperature profile different from that of the steady state and in accordance with the additivity hypothesis predictions. System statistics during a large current fluctuation is independent of the sign of the current, which implies that the optimal profile (as well as higher-order profiles and spatial correlations) are invariant upon current inversion. We also demonstrate that finite-time joint fluctuations of the current and the profile are well described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

  9. Field-Based Video Pre-Test Counseling, Oral Testing, and Telephonic Post-Test Counseling: Implementation of an HIV Field Testing Package among High-Risk Indian Men

    ERIC Educational Resources Information Center

    Snyder, Hannah; Yeldandi, Vijay V.; Kumar, G. Prem; Liao, Chuanhong; Lakshmi, Vemu; Gandham, Sabitha R.; Muppudi, Uma; Oruganti, Ganesh; Schneider, John A.

    2012-01-01

    In India, men who have sex with men (MSM) and truck drivers are high-risk groups that often do not access HIV testing due to stigma and high mobility. This study evaluated a field testing package (FTP) that identified HIV positive participants through video pre-test counseling, OraQuick oral fluid HIV testing, and telephonic post-test counseling…

  10. Field validation of 10-day freshwater sediment toxicity tests using Hyalella azteca and Chironomus tentans

    SciTech Connect

    Becker, D.S.; Bigham, G.N.

    1995-12-31

    Two of the toxicity tests commonly used to evaluate freshwater sediments are the 10-day amphipod (Hyalella azteca) and chironomid (Chironomus tentans) tests. EPA and ASTM have recently developed standardized protocols for these tests. Although both tests are considered sensitive indicators of sediment toxicity, little information exists on how well test results correspond to adverse biological effects in the field. In this study, the lethal and sublethal (i.e., biomass) responses of the two toxicity tests were compared with alterations of benthic macroinvertebrate assemblages (i.e., benthic effects) at 56 stations in Onondaga Lake, New York. The lake has received municipal and industrial discharges for more than 100 years, and sediment chemical concentrations range widely throughout the lake. Toxicity results for Onondaga Lake were compared with reference conditions using the t-test, and benthic effects were determined using classification analysis of log-transformed taxa abundances. In general, a relatively high level of agreement was found between results of the toxicity tests and alterations of benthic assemblages. Significant (P < 0.05) correlations were found between all toxicity test endpoints and taxa richness of benthic assemblages. In addition, significant concordance (P {le} 0.01, binomial test) was found between toxicity designations for the 56 stations based on toxicity tests and toxicity designations based on benthic effects. Despite the general level of agreement among the various biological indicators, chironomid biomass and benthic effects were found to be the most sensitive indicators of toxicity, whereas amphipod survival and biomass were the least sensitive indicators. This study suggests that results of the 10-day amphipod and chironomid toxicity tests are highly predictive of adverse biological effects in the field.

  11. Thermoregulatory response to an organophosphate and carbamate insecticide mixture: testing the assumption of dose-additivity.

    PubMed

    Gordon, Christopher J; Herr, David W; Gennings, Chris; Graff, Jaimie E; McMurray, Matthew; Stork, LeAnna; Coffey, Todd; Hamm, Adam; Mack, Cina M

    2006-01-01

    Most toxicity data are based on studies using single compounds. This study assessed if there is an interaction between mixtures of the anticholinesterase insecticides chlorpyrifos (CHP) and carbaryl (CAR) using hypothermia and cholinesterase (ChE) inhibition as toxicological endpoints. Core temperature (T(c)) was continuously monitored by radiotelemetry in adult Long-Evans rats administered CHP at doses ranging from 0 to 50mg/kg and CAR doses of 0-150 mg/kg. The temperature index (TI), an integration of the change in T(c) over a 12h period, was quantified. Effects of mixtures of CHP and CAR in 2:1 and 1:1 ratios on the TI were examined and the data analyzed using a statistical model designed to assess significant departures from additivity for chemical mixtures. CHP and CAR elicited a marked hypothermia and dose-related decrease in the TI. The TI response to a 2:1 ratio of CHP:CAR was significantly less than that predicted by additivity. The TI response to a 1:1 ratio of CHP and CAR was not significantly different from the predicted additivity. Plasma and brain ChE activity were measured 4h after dosing with CHP, CAR, and mixtures in separate groups of rats. There was a dose-additive interaction for the inhibition of brain ChE for the 2:1 ratio, but an antagonistic effect for the 1:1 ratio. The 2:1 and 1:1 mixtures had an antagonistic interaction on plasma ChE. Overall, the departures from additivity for the physiological (i.e., temperature) and biochemical (i.e., ChE inhibition) endpoints for the 2:1 and 1:1 mixtures studies did not coincide as expected. An interaction between CHP and CAR appears to depend on the ratio of compounds in the mixture as well as the biological endpoint. PMID:16182429

  12. 76 FR 3075 - Availability of an Environmental Assessment for Field Testing Feline Leukemia Vaccine, Live...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-19

    ... Feline Leukemia Vaccine, Live Canarypox Vector AGENCY: Animal and Plant Health Inspection Service, USDA... testing, and then to field test, an unlicensed Feline Leukemia Vaccine, Live Canarypox Vector. The... field testing of this vaccine, examines the potential effects that field testing this veterinary...

  13. Portable narcotics detector and the results obtained in field tests

    NASA Astrophysics Data System (ADS)

    Tumer, Tumay O.; Su, Chih-Wu; Kaplan, Christopher R.; Rigdon, Stephen W.

    1997-02-01

    A compact integrated narcotics detection instrument (CINDI) has been developed at NOVA R&D, Inc. with funding provided by the U.S. Coast Guard. CINDI is designed as a portable sensitive neutron backscatter detector which has excellent penetration for thick and high Z compartment barriers. It also has a highly sensitive detection system for backscattered neutrons and, therefore, uses a very weak californium-252 neutron source. Neutrons backscatter profusely from materials that have a large hydrogen content, such as narcotics. The rate of backscattered neutrons detected is analyzed by a microprocessor and displayed on the control panel. The operator guides the detector along a suspected area and displays in real time the backscattered neutron rate. CINDI is capable of detecting narcotics effectively behind panels made of steel, wood, fiberglass, or even lead-lined materials. This makes it useful for inspecting marine vessels, ship bulkheads, automobiles, structure walls or small sealed containers. The strong response of CINDI to hydrogen-rich materials such as narcotics makes it an effective tool for detecting concealed drugs. Its response has been field tested by NOVA, the U.S. Coast Guard and Brewt Power Systems. The results of the tests show excellent response and specificity to narcotic drugs. Several large shipments of concealed drugs have been discovered during these trials and the results are presented and discussed.

  14. Field tracer-transport tests in unsaturated fractured tuff.

    PubMed

    Hu, Q; Salve, R; Stringfellow, W T; Wang, J S

    2001-09-01

    This paper presents the results of a field investigation in the unsaturated, fractured welded tuff within the Exploratory Studies Facility (ESF) at Yucca Mountain, NV. This investigation included a series of tests during which tracer-laced water was released into a high-permeability zone within a horizontal injection borehole. The tracer concentration was monitored in the seepage collected in an excavated slot about 1.6 m below the borehole. Results showed significant variability in the hydrologic response of fractures and the matrix. Analyses of the breakthrough curves suggest that flow and transport pathways are dynamic, rather than fixed, and related to liquid-release rates. Under high release rates, fractures acted as the predominant flow pathways, with limited fracture-matrix interaction. Under low release rates, fracture flow was comparatively less dominant, with a noticeable contribution from matrix flow. Observations of tracer concentrations rebounding in seepage water, following an interruption of flow, provided evidence of mass exchange between the fast-flowing fractures and slow- or non-flowing regions. The tests also showed the applicability of fluorinated benzoate tracers in situations where multiple tracers of similar physical properties are warranted. PMID:11530924

  15. Comparison of Dynamic Balance in Collegiate Field Hockey and Football Players Using Star Excursion Balance Test

    PubMed Central

    Bhat, Rashi; Moiz, Jamal Ali

    2013-01-01

    Purpose The preliminary study aimed to compare dynamic balance between collegiate athletes competing or training in football and hockey using star excursion balance test. Methods A total thirty university level players, football (n = 15) and field hockey (n = 15) were participated in the study. Dynamic balance was assessed by using star excursion balance test. The testing grid consists of 8 lines each 120 cm in length extending from a common point at 45° increments. The subjects were instructed to maintain a stable single leg stance with the test leg with shoes off and to reach for maximal distance with the other leg in each of the 8 directions. A pencil was used to point and read the distance to which each subject's foot reached. The normalized leg reach distances in each direction were summed for both limbs and the total sum of the mean of summed normalized distances of both limbs were calculated. Results There was no significant difference in all the directions of star excursion balance test scores in both the groups. Additionally, composite reach distances of both groups also found non-significant (P=0.5). However, the posterior (P=0.05) and lateral (P=0.03) normalized reach distances were significantly more in field hockey players. Conclusion Field hockey players and football players did not differ in terms of dynamic balance. PMID:24427482

  16. Results from laboratory and field testing of nitrate measuring spectrophotometers

    USGS Publications Warehouse

    Snazelle, Teri T.

    2015-01-01

    In Phase II, the analyzers were deployed in field conditions at three diferent USGS sites. The measured nitrate concentrations were compared to discrete (reference) samples analyzed by the Direct UV method on a Shimadzu UV1800 bench top spectrophotometer, and by the National Environmental Methods Index (NEMI) method I-2548-11 at the USGS National Water Quality Laboratory. The first deployment at USGS site 0249620 on the East Pearl River in Hancock County, Mississippi, tested the ability of the TriOs ProPs (10-mm path length), Hach NITRATAX (5 mm), Satlantic SUNA (10 mm), and the S::CAN Spectro::lyser (5 mm) to accurately measure low-level (less than 2 mg-N/L) nitrate concentrations while observing the effect turbidity and colored dissolved organic matter (CDOM) would have on the analyzers' measurements. The second deployment at USGS site 01389005 Passaic River below Pompton River at Two Bridges, New Jersey, tested the analyzer's accuracy in mid-level (2-8 mg-N/L) nitrate concentrations. This site provided the means to test the analyzers' performance in two distinct matrices—the Passaic and the Pompton Rivers. In this deployment, three instruments tested in Phase I (TriOS, Hach, and SUNA) were deployed with the S::CAN Spectro::lyser (35 mm) already placed by the New Jersey Water Science Center (WSC). The third deployment at USGS site 05579610 Kickapoo Creek at 2100E Road near Bloomington, Illinois, tested the ability of the analyzers to measure high nitrate concentrations (greater than 8 mg-N/L) in turbid waters. For Kickapoo Creek, the HIF provided the TriOS (10 mm) and S::CAN (5 mm) from Phase I, and a SUNA V2 (5 mm) to be deployed adjacent to the Illinois WSC-owned Hach (2 mm). A total of 40 discrete samples were collected from the three deployment sites and analyzed. The nitrate concentration of the samples ranged from 0.3–22.2 mg-N/L. The average absolute difference between the TriOS measurements and discrete samples was 0.46 mg-N/L. For the combined data

  17. 75 FR 4323 - Additional Quantitative Fit-testing Protocols for the Respiratory Protection Standard

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-27

    ... performed particle counts on samples collected during the Study. Table 1 provides the exercise and sampling... revised PortaCount quantitative fit-testing protocols are not sufficiently accurate or reliable to include...) to Appendix A of ] its Respiratory Protection Standard (see 69 FR 46986). OSHA also published...

  18. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... target so as to suffer the maximum damage to its containment. The height of the drop measured from the lowest part of the packaging specimen to the upper surface of the target must be 9 m (30 feet) or greater. The target must be as specified in § 173.465(c)(5). (2) Penetration test. The specimen must...

  19. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... target so as to suffer the maximum damage to its containment. The height of the drop measured from the lowest part of the packaging specimen to the upper surface of the target must be 9 m (30 feet) or greater. The target must be as specified in § 173.465(c)(5). (2) Penetration test. The specimen must...

  20. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... target so as to suffer the maximum damage to its containment. The height of the drop measured from the lowest part of the packaging specimen to the upper surface of the target must be 9 m (30 feet) or greater. The target must be as specified in § 173.465(c)(5). (2) Penetration test. The specimen must...

  1. Testing the Limits: The Purposes and Effects of Additional, External Elementary Mathematics Assessment

    ERIC Educational Resources Information Center

    Lombardi, Karen Ann

    2011-01-01

    This mixed-methods case study focuses on the third through fifth grade classrooms at a public elementary school in a Midwestern urban school district where the Northwest Evaluation Association's (NWEA) Measures of Academic Progress (MAP) assessment is being implemented. According to the school district, the goals of these tests are: to show…

  2. Validation and Estimation of Additive Genetic Variation Associated with DNA Tests for Quantitative Beef Cattle Traits

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The U.S. National Beef Cattle Evaluation Consortium (NBCEC) has been involved in the validation of commercial DNA tests for quantitative beef quality traits since their first appearance on the U.S. market in the early 2000s. The NBCEC Advisory Council initially requested that the NBCEC set up a syst...

  3. Software for Information Storage and Retrieval Tested, Evaluated and Compared: Part VI--Various Additional Programs.

    ERIC Educational Resources Information Center

    Sieverts, Eric G.; And Others

    1993-01-01

    Reports on tests evaluating nine microcomputer software packages designed for information storage and retrieval: BRS-Search, dtSearch, InfoBank, Micro-OPC, Q&A, STN-PFS, Strix, TINman, and ZYindex. Tables and narrative evaluations detail results related to security, hardware, user features, search capability, indexing, input, maintenance of files,…

  4. Avoiding Split Attention in Computer-Based Testing: Is Neglecting Additional Information Facilitative?

    ERIC Educational Resources Information Center

    Jarodzka, Halszka; Janssen, Noortje; Kirschner, Paul A.; Erkens, Gijsbert

    2015-01-01

    This study investigated whether design guidelines for computer-based learning can be applied to computer-based testing (CBT). Twenty-two students completed a CBT exam with half of the questions presented in a split-screen format that was analogous to the original paper-and-pencil version and half in an integrated format. Results show that students…

  5. 75 FR 2122 - Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ...) standard HRF-1-1979 (HRF-1). See Appendix A1, section 2.2; 47 FR 34517 (Aug. 10, 1982). HRF-1 specifies... ensure the consistent application of DOE's current test procedure to refrigerator-freezers with French doors, bottom-mounted freezers, and through-the-door (TTD) ice service (French door TTD models)....

  6. Field testing advanced geothermal turbodrill (AGT). Phase 1 final report

    SciTech Connect

    Maurer, W.C.; Cohen, J.H.

    1999-06-01

    Maurer Engineering developed special high-temperature geothermal turbodrills for LANL in the 1970s to overcome motor temperature limitations. These turbodrills were used to drill the directional portions of LANL`s Hot Dry Rock Geothermal Wells at Fenton Hill, New Mexico. The Hot Dry Rock concept is to drill parallel inclined wells (35-degree inclination), hydraulically fracture between these wells, and then circulate cold water down one well and through the fractures and produce hot water out of the second well. At the time LANL drilled the Fenton Hill wells, the LANL turbodrill was the only motor in the world that would drill at the high temperatures encountered in these wells. It was difficult to operate the turbodrills continuously at low speed due to the low torque output of the LANL turbodrills. The turbodrills would stall frequently and could only be restarted by lifting the bit off bottom. This allowed the bit to rotate at very high speeds, and as a result, there was excessive wear in the bearings and on the gauge of insert roller bits due to these high rotary speeds. In 1998, Maurer Engineering developed an Advanced Geothermal Turbodrill (AGT) for the National Advanced Drilling and Excavation Technology (NADET) at MIT by adding a planetary speed reducer to the LANL turbodrill to increase its torque and reduce its rotary speed. Drilling tests were conducted with the AGT using 12 1/2-inch insert roller bits in Texas Pink Granite. The drilling tests were very successful, with the AGT drilling 94 ft/hr in Texas Pink Granite compared to 45 ft/hr with the LANL turbodrill and 42 ft/hr with a rotary drill. Field tests are currently being planned in Mexico and in geothermal wells in California to demonstrate the ability of the AGT to increase drilling rates and reduce drilling costs.

  7. Terahertz imaging and tomography as efficient instruments for testing polymer additive manufacturing objects.

    PubMed

    Perraud, J B; Obaton, A F; Bou-Sleiman, J; Recur, B; Balacey, H; Darracq, F; Guillet, J P; Mounaix, P

    2016-05-01

    Additive manufacturing (AM) technology is not only used to make 3D objects but also for rapid prototyping. In industry and laboratories, quality controls for these objects are necessary though difficult to implement compared to classical methods of fabrication because the layer-by-layer printing allows for very complex object manufacturing that is unachievable with standard tools. Furthermore, AM can induce unknown or unexpected defects. Consequently, we demonstrate terahertz (THz) imaging as an innovative method for 2D inspection of polymer materials. Moreover, THz tomography may be considered as an alternative to x-ray tomography and cheaper 3D imaging for routine control. This paper proposes an experimental study of 3D polymer objects obtained by additive manufacturing techniques. This approach allows us to characterize defects and to control dimensions by volumetric measurements on 3D data reconstructed by tomography.

  8. Terahertz imaging and tomography as efficient instruments for testing polymer additive manufacturing objects.

    PubMed

    Perraud, J B; Obaton, A F; Bou-Sleiman, J; Recur, B; Balacey, H; Darracq, F; Guillet, J P; Mounaix, P

    2016-05-01

    Additive manufacturing (AM) technology is not only used to make 3D objects but also for rapid prototyping. In industry and laboratories, quality controls for these objects are necessary though difficult to implement compared to classical methods of fabrication because the layer-by-layer printing allows for very complex object manufacturing that is unachievable with standard tools. Furthermore, AM can induce unknown or unexpected defects. Consequently, we demonstrate terahertz (THz) imaging as an innovative method for 2D inspection of polymer materials. Moreover, THz tomography may be considered as an alternative to x-ray tomography and cheaper 3D imaging for routine control. This paper proposes an experimental study of 3D polymer objects obtained by additive manufacturing techniques. This approach allows us to characterize defects and to control dimensions by volumetric measurements on 3D data reconstructed by tomography. PMID:27140357

  9. FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

    SciTech Connect

    Unknown

    2001-05-31

    Western Research Institute (WRI) is commercializing Diesel Dog Portable Soil Test Kits for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to the technology by taking the method through the American Society for Testing and Materials (ASTM) approval and validation processes. The method is designated ASTM Method D-5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In FY 99, twenty-five preproduction kits were successfully constructed in cooperation with CF Electronics, Inc., of Laramie, Wyoming. The kit components work well and the kits are fully operational. In the calendar year 2000, kits were provided to the following entities who agreed to participate as FY 99 and FY 00 JSR (Jointly Sponsored Research) cosponsors and use the kits as opportunities arose for field site work: Wyoming Department of Environmental Quality (DEQ) (3 units), F.E. Warren Air Force Base, Gradient Corporation, The Johnson Company (2 units), IT Corporation (2 units), TRC Environmental Corporation, Stone Environmental, ENSR, Action Environmental, Laco Associates, Barenco, Brown and Caldwell, Dames and Moore Lebron LLP, Phillips Petroleum, GeoSyntek, and the State of New Mexico. By early 2001, ten kits had been returned to WRI following the six-month evaluation period. On return, the components of all ten kits were fully functional. The kits were upgraded with circuit modifications, new polyethylene foam inserts, and updated instruction manuals.

  10. Site 1 field testing for cooling-water treatment. Final report

    SciTech Connect

    Litherland, S.T.; Owen, M.L.; Scholl, F.A.; Kamas, J.W.; Nassos, P.A.

    1985-06-01

    The Electric Power Research Institute is sponsoring a three phase research project to develop a design and operating methodology for recirculating cooling water systems at high concentration factors. To expand the available data base for cooling water systems at high concentration factors, a portable field test unit (FTU) has been designed and fabricated for operation at sites with different makeup water qualities. For a ten month period during 1981, the FTU was operated at the first site, Comanche Generating Station in Pueblo, Colorado. During the field testing, several cooling water treatment options were used to increase the concentration factor for operating the FTU. These water treatment options included: (1) sulfuric acid addition for alkalinity control; (2) lime-soda makeup softening; (3) lime-soda sidestream softening; (4) combined lime-soda makeup and sidestream softening; and (5) inhibitor addition for gypsum scale control. The purpose of this report is to present a detailed discussion of all Site 1 field test activities, including FTU operation and data interpretation and analyses. 11 refs., 68 figs., 70 tabs.

  11. Jet-Surface Interaction Test: Far-Field Noise Results

    NASA Technical Reports Server (NTRS)

    Brown, Clifford A.

    2012-01-01

    Many configurations proposed for the next generation of aircraft rely on the wing or other aircraft surfaces to shield the engine noise from the observers on the ground. However, the ability to predict the shielding effect and any new noise sources that arise from the high-speed jet flow interacting with a hard surface is currently limited. Furthermore, quality experimental data from jets with surfaces nearby suitable for developing and validating noise prediction methods are usually tied to a particular vehicle concept and, therefore, very complicated. The Jet/Surface Interaction Test was intended to supply a high quality set of data covering a wide range of surface geometries and positions and jet flows to researchers developing aircraft noise prediction tools. During phase one, the goal was to measure the noise of a jet near a simple planar surface while varying the surface length and location in order to: (1) validate noise prediction schemes when the surface is acting only as a jet noise shield and when the jet/surface interaction is creating additional noise, and (2) determine regions of interest for more detailed tests in phase two. To meet these phase one objectives, a flat plate was mounted on a two-axis traverse in two distinct configurations: (1) as a shield between the jet and the observer (microphone array) and (2) as a reflecting surface on the opposite side of the jet from the observer.

  12. Neutron measurements of stresses in a test artifact produced by laser-based additive manufacturing

    SciTech Connect

    Gnäupel-Herold, Thomas; Slotwinski, John; Moylan, Shawn

    2014-02-18

    A stainless steel test artifact produced by Direct Metal Laser Sintering and similar to a proposed standardized test artifact was examined using neutron diffraction. The artifact contained a number of structures with different aspect ratios pertaining to wall thickness, height above base plate, and side length. Through spatial resolutions of the order of one millimeter the volumetric distribution of stresses in several was measured. It was found that the stresses peak in the tensile region around 500 MPa near the top surface, with balancing compressive stresses in the interior. The presence of a support structure (a one millimeter high, thin walled, hence weaker, lattice structure deposited on the base plate, followed by a fully dense AM structure) has only minor effects on the stresses.

  13. A Pilot Test of the Additive Benefits of Physical Exercise to CBT for OCD.

    PubMed

    Rector, Neil A; Richter, Margaret A; Lerman, Bethany; Regev, Rotem

    2015-01-01

    The majority of "responders" to first-line cognitive-behavioural therapy (CBT) and pharmacological treatments for obsessive-compulsive disorder (OCD) are left with residual symptoms that are clinically relevant and disabling. Therefore, there is pressing need for widely accessible efficacious alternative and/or adjunctive treatments for OCD. Accumulating evidence suggests that physical exercise may be one such intervention in the mood and anxiety disorders broadly, although we are aware of only two positive small-scale pilot studies that have tested its clinical benefits in OCD. This pilot study aimed to test the feasibility and preliminary efficacy of adding a structured physical exercise programme to CBT for OCD. A standard CBT group was delivered concurrently with a 12-week customized exercise programme to 11 participants. The exercise regimen was individualized for each participant based on peak heart rate measured using an incremental maximal exercise test. Reports of exercise adherence across the 12-week regimen exceeded 80%. A paired-samples t-test indicated very large treatment effects in Yale-Brown Obsessive-Compulsive Scale scores from pre- to post-treatment in CBT group cohorts led by expert CBT OCD specialists (d = 2.55) and junior CBT clinician non-OCD specialists (d = 2.12). These treatment effects are very large and exceed effects typically observed with individual and group-based CBT for OCD based on leading meta-analytic reviews, as well as previously obtained treatment effects for CBT using the same recruitment protocol without exercise. As such, this pilot work demonstrates the feasibility and significant potential clinical utility of a 12-week aerobic exercise programme delivered in conjunction with CBT for OCD. PMID:25738234

  14. A Pilot Test of the Additive Benefits of Physical Exercise to CBT for OCD.

    PubMed

    Rector, Neil A; Richter, Margaret A; Lerman, Bethany; Regev, Rotem

    2015-01-01

    The majority of "responders" to first-line cognitive-behavioural therapy (CBT) and pharmacological treatments for obsessive-compulsive disorder (OCD) are left with residual symptoms that are clinically relevant and disabling. Therefore, there is pressing need for widely accessible efficacious alternative and/or adjunctive treatments for OCD. Accumulating evidence suggests that physical exercise may be one such intervention in the mood and anxiety disorders broadly, although we are aware of only two positive small-scale pilot studies that have tested its clinical benefits in OCD. This pilot study aimed to test the feasibility and preliminary efficacy of adding a structured physical exercise programme to CBT for OCD. A standard CBT group was delivered concurrently with a 12-week customized exercise programme to 11 participants. The exercise regimen was individualized for each participant based on peak heart rate measured using an incremental maximal exercise test. Reports of exercise adherence across the 12-week regimen exceeded 80%. A paired-samples t-test indicated very large treatment effects in Yale-Brown Obsessive-Compulsive Scale scores from pre- to post-treatment in CBT group cohorts led by expert CBT OCD specialists (d = 2.55) and junior CBT clinician non-OCD specialists (d = 2.12). These treatment effects are very large and exceed effects typically observed with individual and group-based CBT for OCD based on leading meta-analytic reviews, as well as previously obtained treatment effects for CBT using the same recruitment protocol without exercise. As such, this pilot work demonstrates the feasibility and significant potential clinical utility of a 12-week aerobic exercise programme delivered in conjunction with CBT for OCD.

  15. Additive Manufacturing Thermal Performance Testing of Single Channel GRCop-84 SLM Components

    NASA Technical Reports Server (NTRS)

    Garcia, Chance P.; Cross, Matthew

    2014-01-01

    The surface finish found on components manufactured by sinter laser manufacturing (SLM) is rougher (0.013 - 0.0006 inches) than parts made using traditional fabrication methods. Internal features and passages built into SLM components do not readily allow for roughness reduction processes. Alternatively, engineering literature suggests that the roughness of a surface can enhance thermal performance within a pressure drop regime. To further investigate the thermal performance of SLM fabricated pieces, several GRCop-84 SLM single channel components were tested using a thermal conduction rig at MSFC. A 20 kW power source running at 25% duty cycle and 25% power level applied heat to each component while varying water flow rates between 2.1 - 6.2 gallons/min (GPM) at a supply pressure of 550 to 700 psi. Each test was allowed to reach quasi-steady state conditions where pressure, temperature, and thermal imaging data were recorded. Presented in this work are the heat transfer responses compared to a traditional machined OHFC Copper test section. An analytical thermal model was constructed to anchor theoretical models with the empirical data.

  16. Additional Value of CH₄ Measurement in a Combined (13)C/H₂ Lactose Malabsorption Breath Test: A Retrospective Analysis.

    PubMed

    Houben, Els; De Preter, Vicky; Billen, Jaak; Van Ranst, Marc; Verbeke, Kristin

    2015-09-07

    The lactose hydrogen breath test is a commonly used, non-invasive method for the detection of lactose malabsorption and is based on an abnormal increase in breath hydrogen (H₂) excretion after an oral dose of lactose. We use a combined (13)C/H₂ lactose breath test that measures breath (13)CO₂ as a measure of lactose digestion in addition to H₂ and that has a better sensitivity and specificity than the standard test. The present retrospective study evaluated the results of 1051 (13)C/H₂ lactose breath tests to assess the impact on the diagnostic accuracy of measuring breath CH₄ in addition to H₂ and (13)CO₂. Based on the (13)C/H₂ breath test, 314 patients were diagnosed with lactase deficiency, 138 with lactose malabsorption or small bowel bacterial overgrowth (SIBO), and 599 with normal lactose digestion. Additional measurement of CH₄ further improved the accuracy of the test as 16% subjects with normal lactose digestion and no H₂-excretion were found to excrete CH₄. These subjects should have been classified as subjects with lactose malabsorption or SIBO. In conclusion, measuring CH₄-concentrations has an added value to the (13)C/H₂ breath test to identify methanogenic subjects with lactose malabsorption or SIBO.

  17. Additional Value of CH₄ Measurement in a Combined (13)C/H₂ Lactose Malabsorption Breath Test: A Retrospective Analysis.

    PubMed

    Houben, Els; De Preter, Vicky; Billen, Jaak; Van Ranst, Marc; Verbeke, Kristin

    2015-09-01

    The lactose hydrogen breath test is a commonly used, non-invasive method for the detection of lactose malabsorption and is based on an abnormal increase in breath hydrogen (H₂) excretion after an oral dose of lactose. We use a combined (13)C/H₂ lactose breath test that measures breath (13)CO₂ as a measure of lactose digestion in addition to H₂ and that has a better sensitivity and specificity than the standard test. The present retrospective study evaluated the results of 1051 (13)C/H₂ lactose breath tests to assess the impact on the diagnostic accuracy of measuring breath CH₄ in addition to H₂ and (13)CO₂. Based on the (13)C/H₂ breath test, 314 patients were diagnosed with lactase deficiency, 138 with lactose malabsorption or small bowel bacterial overgrowth (SIBO), and 599 with normal lactose digestion. Additional measurement of CH₄ further improved the accuracy of the test as 16% subjects with normal lactose digestion and no H₂-excretion were found to excrete CH₄. These subjects should have been classified as subjects with lactose malabsorption or SIBO. In conclusion, measuring CH₄-concentrations has an added value to the (13)C/H₂ breath test to identify methanogenic subjects with lactose malabsorption or SIBO. PMID:26371034

  18. Field-Testing of an Active Laser Tracking System

    NASA Astrophysics Data System (ADS)

    Markov, V.; Khiznyak, A.; Woll, D.; Liu, S.

    -mirror module for laser beam steering and detectors, all set on a single platform. In the initial ALTS design, the laser module is conceptualized in coupled-cavitiesarchitecturewith a synchronously pumped gain media, a four-wave mixing PCM. The four-wave mixing arrangement uses optical phase conjugation to compensate for spatial inhomogeneities of the atmosphere. A significant innovation in the proposed approach is in its perspective capabilities to detect and measure the critical parameters in the returned signal that should allow to directly measure spatial/angular position and velocity of the target. This report will cover the system analysis, the ALTS design, test plan and exit criteria, functional and operational tests, and test results at Edwards AFB Range field.

  19. Field Testing GEOICE: A Next-Generation Polar Seismometer

    NASA Astrophysics Data System (ADS)

    Beaudoin, B. C.; Winberry, J. P.; Huerta, A. D.; Chung, P.; Parker, T.; Anderson, K. R.; Bilek, S. L.; Carpenter, P.

    2015-12-01

    We report on the development of a new NSF MRI-community supported seismic observatory designed for studies in ice-covered regions - the Geophysical Earth Observatory for Ice Covered Environs (GEOICE). This project is motivated by the need to densify and optimize the collection of high-quality seismic data relevant to key solid Earth and cryosphere science questions. The GEOICE instruments and their power and other ancillary systems are being designed to require minimal installation time and logistical load (i.e., size and weight), while maximizing ease-of-use in the field. The system is capable of advanced data handling and telemetry while being able to withstand conditions associated with icy environments, including cold/wet conditions and high-latitude solar limitations. The instrument capability will include a hybrid seismograph pool of broadband and intermediate elements for observation of both long-period signals (e.g, long-period surface waves and slow sources) and intermediate-to-short-period signals (e.g., teleseismic body waves, local seismicity, and impulsive or extended glaciogenic signals).Key features will include a design that integrates the seismometer and digitizer into a single, environmentally and mechanically robust housing; very low power requirements (~1 watt) for the intermediate-band systems; and advanced power systems that optimize battery capacity and operational limits. The envisioned ~100 element GEOICE instruments will nearly double the current polar inventory of stations and will be maintained and supported at the IRIS PASSCAL Instrument Center to ensure full and flexible peer-reviewed community use. Prototype instruments are currently deployed in Antarctica and Alaska, with a larger Antarctic deployment planned for the 2015-2016 season. The results of these field tests will help to refine instrumentation design and lead to the production of robust and capable next-generation seismic sensors.

  20. Advanced Rooftop Control (ARC) Retrofit: Field-Test Results

    SciTech Connect

    Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

    2013-07-31

    The multi-year research study was initiated to find solutions to improve packaged equipment operating efficiency in the field. Pacific Northwest National Laboratory (PNNL), with funding from the U.S. Department of Energy’s (DOE’s) Building Technologies Office (BTO) and Bonneville Power Administration (BPA) conducted this research, development and demonstration (RD&D) study. Packaged equipment with constant speed supply fans is designed to provide ventilation at the design rate at all times when the fan is operating as required by building code. Although there are a number of hours during the day when a building may not be fully occupied or the need for ventilation is lower than designed, the ventilation rate cannot be adjusted easily with a constant speed fan. Therefore, modulating the supply fan in conjunction with demand controlled ventilation (DCV) will not only reduce the coil energy but also reduce the fan energy. The objective of this multi-year research, development and demonstration project was to determine the magnitude of energy savings achievable by retrofitting existing packaged rooftop air conditioners with advanced control strategies not ordinarily used for packaged units. First, through detailed simulation analysis, it was shown that significant energy (between 24% and 35%) and cost savings (38%) from fan, cooling and heating energy consumption could be realized when packaged air conditioning units with gas furnaces are retrofitted with advanced control packages (combining multi-speed fan control, integrated economizer controls and DCV). The simulation analysis also showed significant savings for heat pumps (between 20% and 60%). The simulation analysis was followed by an extensive field test of a retrofittable advanced rooftop unit (RTU) controller.

  1. Status report on the forced flow high field test facility SULTAN

    SciTech Connect

    Horvath, I.; Balsamo, E.; Pasotti, G.; Ricci, M.; Sacchetti, N.; Vecsey, G.; Weymuth, P.; Zellweger, J.

    1983-05-01

    The construction of the Test Facility SULTAN - a common action of three European laboratories: ENEA (I-Frascati), ECN (NL-Petten) and SIN (CH-Villigen) is near completion. In this paper, the status of the contributions of the different partners is described: (a) The SIN part of the facility, the cryogenic system, the current leads, the power supplies and the data acquisition system have been put into operation. Results of these tests are presented. (b) The background field will be generated by two concentric solenoids. The ENEA contribution is concerned with the realization of the outer solenoid. This coil, which has been recently completed, will provide a 6 T field in the useful region, the remaining 2 T being supplied by the coaxial ECN insert coil. Details of the design, winding technique, hydraulic circuitry as well as instrumentation of both coils are given and discussed. In addition, the future upgrading to 12 T is outlined.

  2. Field Test Result of 10MVA/20MJ SMES for Load Fluctuation Compensation

    NASA Astrophysics Data System (ADS)

    Nagaya, Shigeo; Nagata, Tatsuya; Hirano, Naoki; Tamada, Tsutomu; Nijo, Yoshio; Katagiri, Toshio; Yamane, Minoru

    SMES of the10,000kW for the power control in power system has been manufactured, and connected to a real power grid. In addition, innovative basic researches, for example, low cost converter, maintenance-free cryo-coolers, inter-locks system and so on, have also been developed. The SMES was installed in the metal rolling factory with hydro power plant. Field test has been carried out for load fluctuation compensation. SMES was able to compensate for the active power according to the fluctuating load, and confirm the situation with a smooth load change of 11kV bus of hydro power stations. In this paper, field test results are presented.

  3. Selecting visual field tests and assessing visual field deterioration in glaucoma.

    PubMed

    Nouri-Mahdavi, Kouros

    2014-12-01

    Testing the peripheral field of vision is the mainstay for detection of glaucoma deterioration. Various methods and algorithms are currently available for detection of early glaucoma or establishing disease progression. Alternative testing strategies such as frequency doubling technology perimetry or short-wavelength automated perimetry have been extensively explored over the last 2 decades. The former has been found most promising for detection of earliest evidence of functional glaucoma damage when the standard achromatic perimetry results are still within the normal range. However, standard achromatic perimetry remains the standard technique for establishing deterioration of the disease. Both trend and event analyses are used for establishing change within series of visual fields. Trend analyses provide the clinician with rates of progression, putting the speed of glaucoma progression in the context of patient longevity, whereas event analyses demonstrate a "step" change regardless of the length of time it took for this amount of change to occur. The two techniques are complementary and should be used concurrently.

  4. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-Exceed test procedures, use the test procedures and equipment specified in 40 CFR part 1065, subpart J. ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing...

  5. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-Exceed test procedures, use the test procedures and equipment specified in 40 CFR part 1065, subpart J. ... 40 Protection of Environment 19 2011-07-01 2011-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing...

  6. Formalin treatments pass new tests. Additional notes on the control of ecto-parasitic protozoa

    USGS Publications Warehouse

    1940-01-01

    After the completion of the eхреriments reported recently, in which the efficacy of formalin in controlling infections of Gostia mecatrix was demonstrated, the author was afforded an opportunity to test the value of formalin solutions in combatting established mixed infections of (Gyrodactylus, Tricbodina, Cyclochaeta) and a stalked protozoan on rainbow trout fingerlings. This opportunity was provided through the courtesy and cooperation of Clarence F. Pautzke, Chief Biologist for the Washington State Game Department, and Lee Walters, Superintendent of the Washington State Hatchery at Seward Park, Seattle.

  7. The aspartame story: a model for the clinical testing of a food additive.

    PubMed

    Stegink, L D

    1987-07-01

    Toxicology is based on the premise that all compounds are toxic at some dose. Thus, it is not surprising that very large doses of aspartame (or its components--aspartate, phenylalanine, and methanol) produce deleterious effects in sensitive animal species. The critical question is whether aspartame ingestion is potentially harmful to humans at normal use and potential abuse levels. This paper reviews clinical studies testing the effects of various doses of aspartame upon blood levels of aspartate, phenylalanine, and methanol. These studies demonstrate that blood levels of these compounds are well below levels associated with adverse effects in sensitive animal species.

  8. Field-testing competing runoff source and hydrochemical conceptualisations

    NASA Astrophysics Data System (ADS)

    Western, A. W.; Saffarpour, S.; Adams, R.; Costelloe, J. F.; McDonnell, J.

    2014-12-01

    There are competing conceptualisations of heterogeneity in catchment systems. It is often convenient to divide catchments into zones, for example the soil profile, groundwater aquifers (saturated zone), riparian zones, etc. We also often divide flow sources into distinct categories such as surface runoff, interflow and baseflow, implying a few distinct stores of water. In tracer hydrology we typically assume water from such zones has distinct and invariant chemistry that is used to infer the runoff source mixture through conservative mixing model techniques such as End-Member Mixing Analysis (EMMA). An alternative conceptualisation is that catchments consist of a large number of stores with varying residence times. In this case individual stores contribute a variable proportion of flow and may have a temporally varying composition due to processes such as evapo-concentration. Hence they have a variable influence on the hydrochemistry of runoff. In this presentation, examples from two field studies in southern Australia will be presented that examine the relationships between hydrologic and hydrochemical conceptualisations and the relative variation within and between different hydrologic zones. The implications for water quality behaviour will be examined and the additional behavioural complexities associated with interactions between runoff pathways for non-conservative chemical species will be discussed.

  9. Field tests of acoustic telemetry for a portable coastal observatory

    USGS Publications Warehouse

    Martini, M.; Butman, B.; Ware, J.; Frye, D.

    2006-01-01

    Long-term field tests of a low-cost acoustic telemetry system were carried out at two sites in Massachusetts Bay. At each site, an acoustic Doppler current profiler mounted on a bottom tripod was fitted with an acoustic modem to transmit data to a surface buoy; electronics mounted on the buoy relayed these data to shore via radio modem. The mooring at one site (24 m water depth) was custom-designed for the telemetry application, with a custom designed small buoy, a flexible electro-mechanical buoy to mooring joint using a molded chain connection to the buoy, quick-release electro-mechanical couplings, and dual hydrophones suspended 7 m above the bottom. The surface buoy at the second site (33 m water depth) was a U.S. Coast Guard (USCG) channel buoy fitted with telemetry electronics and clamps to hold the hydrophones. The telemetry was tested in several configurations for a period of about four years. The custom-designed buoy and mooring provided nearly error-free data transmission through the acoustic link under a variety of oceanographic conditions for 261 days at the 24 m site. The electro mechanical joint, cables and couplings required minimal servicing and were very reliable, lasting 862 days deployed before needing repairs. The acoustic communication results from the USCG buoy were poor, apparently due to the hard cobble bottom, noise from the all-steel buoy, and failure of the hydrophone assembly. Access to the USCG buoy at sea required ideal weather. ??2006 IEEE.

  10. Site Characterization for a Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Kuhlman, K. L.; Hardin, E. L.; Freeze, G. A.; Sassani, D.; Brady, P. V.

    2015-12-01

    The US Department of Energy Office of Nuclear Energy is at the beginning of 5-year Deep Borehole Field Test (DBFT) to investigate the feasibility of constructing and characterizing two boreholes in crystalline basement rock to a depth of 5 km (16,400 ft). The concept of deep borehole disposal for radioactive waste has some advantages over mined repositories, including incremental construction and loading, the enhanced natural barriers provided by deep continental crystalline basement, and reduced site characterization. Site characterization efforts need to determine an eligible site that does not have the following disqualifying characteristics: greater than 2 km to crystalline basement, upward vertical fluid potential gradients, presence of economically exploitable natural resources, presence of high permeability connection to the shallow subsurface, and significant probability of future seismic or volcanic activity. Site characterization activities for the DBFT will include geomechanical (i.e., rock in situ stress state, and fluid pressure), geological (i.e., rock and fracture infill lithology), hydrological (i.e., quantity of fluid, fluid convection properties, and solute transport mechanisms), and geochemical (i.e., rock-water interaction and natural tracers) aspects. Both direct (i.e., sampling and in situ testing) and indirect (i.e., borehole geophysical) methods are planned for efficient and effective characterization of these site aspects and physical processes. Borehole-based characterization will be used to determine the variability of system state (i.e., stress, pressure, temperature, and chemistry) with depth, and interpretation of material and system parameters relevant to numerical site simulation. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE

  11. Direct Field and Reverberant Chamber Acoustic Test Comparisons

    NASA Technical Reports Server (NTRS)

    OConnell, Michael

    2007-01-01

    Reverberant and direct acoustic test comparisons were analyzed in this viewgraph presentation. The acoustic test data set includes: 1) CloudSat antenna subjected to PF reverberant chamber acoustic test; 2) CloudSat subjected to a PF direct speaker acoustic test; and 3) DAWN flight spacecraft subjected to PF direct speaker and a workmanship reverberant chamber acoustic test.

  12. Evolving test fields in a black-hole geometry

    NASA Astrophysics Data System (ADS)

    Andersson, Nils

    1997-01-01

    We consider the initial value problem for a massless scalar field in the Schwarzschild geometry. When constructed using a complex-frequency approach the necessary Green's function splits into three components. We discuss all of these in some detail. (1) The contribution from the singularities (the quasinormal modes of the black hole) is approximated and the mode sum is demonstrated to converge after a certain well-defined time in the evolution. A dynamic description of the mode excitation is introduced and tested. (2) It is shown how a straightforward low-frequency approximation to the integral along the branch cut in the black-hole Green's function leads to the anticipated power-law falloff at very late times. We also calculate higher order corrections to this tail and show that they provide an important complement to the leading order. (3) The high-frequency problem is also considered. We demonstrate that the combination of the obtained approximations for the quasinormal modes and the power-law tail provide a complete description of the evolution at late times. Problems that arise (in the complex-frequency picture) for early times are also discussed, as is the fact that many of the presented results generalize to, for example, Kerr black holes.

  13. Rigorously testing multialternative decision field theory against random utility models.

    PubMed

    Berkowitsch, Nicolas A J; Scheibehenne, Benjamin; Rieskamp, Jörg

    2014-06-01

    Cognitive models of decision making aim to explain the process underlying observed choices. Here, we test a sequential sampling model of decision making, multialternative decision field theory (MDFT; Roe, Busemeyer, & Townsend, 2001), on empirical grounds and compare it against 2 established random utility models of choice: the probit and the logit model. Using a within-subject experimental design, participants in 2 studies repeatedly choose among sets of options (consumer products) described on several attributes. The results of Study 1 showed that all models predicted participants' choices equally well. In Study 2, in which the choice sets were explicitly designed to distinguish the models, MDFT had an advantage in predicting the observed choices. Study 2 further revealed the occurrence of multiple context effects within single participants, indicating an interdependent evaluation of choice options and correlations between different context effects. In sum, the results indicate that sequential sampling models can provide relevant insights into the cognitive process underlying preferential choices and thus can lead to better choice predictions.

  14. The Savannah River Technology Center environmental monitoring field test platform

    SciTech Connect

    Rossabi, J.

    1993-03-05

    Nearly all industrial facilities have been responsible for introducing synthetic chemicals into the environment. The Savannah River Site is no exception. Several areas at the site have been contaminated by chlorinated volatile organic chemicals. Because of the persistence and refractory nature of these contaminants, a complete clean up of the site will take many years. A major focus of the mission of the Environmental Sciences Section of the Savannah River Technology Center is to develop better, faster, and less expensive methods for characterizing, monitoring, and remediating the subsurface. These new methods can then be applied directly at the Savannah River Site and at other contaminated areas in the United States and throughout the world. The Environmental Sciences Section has hosted field testing of many different monitoring technologies over the past two years primarily as a result of the Integrated Demonstration Program sponsored by the Department of Energy`s Office of Technology Development. This paper provides an overview of some of the technologies that have been demonstrated at the site and briefly discusses the applicability of these techniques.

  15. Field test of a post-closure radiation monitor

    SciTech Connect

    Reed, S.E.; Christy, C.E.; Heath, R.E.

    1995-10-01

    The DOE is conducting remedial actions at many sites contaminated with radioactive materials. After closure of these sites, long-term subsurface monitoring is typically required by law. This monitoring is generally labor intensive and expensive using conventional sampling and analysis techniques. The U.S. Department of Energy`s Morgantown Energy Technology Center (METC) has contracted with Babcock and Wilcox to develop a Long-Term Post-Closure Radiation Monitoring System (LPRMS) to reduce these monitoring costs. The system designed in Phase I of this development program monitors gamma radiation using a subsurface cesium iodide scintillator coupled to above-ground detection electronics using optical waveguide. The radiation probe can be installed to depths up to 50 meters using cone penetrometer techniques, and requires no downhole electrical power. Multiplexing, data logging and analysis are performed at a central location. A prototype LPRMS probe was built, and B&W and FERMCO field tested this monitoring probe at the Fernald Environmental Management Project in the fall of 1994 with funding from the DOE`s Office of Technology Development (EM-50) through METC. The system was used measure soil and water with known uranium contamination levels, both in drums and in situ depths up to 3 meters. For comparison purposes measurements were also performed using a more conventional survey probe with a sodium iodide scintillator directly butt-coupled to detection electronics.

  16. What Predicts Changes in Useful Field of View Test Performance?

    PubMed Central

    Lunsman, Melissa; Edwards, Jerri D.; Andel, Ross; Small, Brent J.; Ball, Karlene K.; Roenker, Daniel L.

    2015-01-01

    The Useful Field of View Test (UFOV1) has been used to examine age-related changes in visual processing and cognition and as an indicator of everyday performance outcomes, particularly driving, for over 20 years. How UFOV performance changes with age and what may impact such changes have not previously been investigated longitudinally. Predictors of change in UFOV performance over a five-year period among control-group participants (n = 690) from the Advanced Cognitive Training for Independent and Vital Elderly (ACTIVE) study were examined. Random effects models were estimated with four-subtest total UFOV as the outcome and baseline age, education, gender, race, visual acuity, depressive symptoms, mental status, and self-rated health, as well as attrition, as predictors. UFOV performance generally followed a curvilinear pattern, improving and then declining over time. Only increased age was consistently related to greater declines in UFOV performance over time. UFOV and WAIS-R Digit Symbol Substitution (DSS), a standard measure of cognitive speed, had similar trajectories of change. The implications of these results are discussed. PMID:19140660

  17. Field test of a wideband downhole EM transmitter

    SciTech Connect

    Becker, Alex; Lee, Ki Ha; Reginato, Lou

    1999-07-01

    A viable large bandwidth TEM transmitter can be constructed using very conventional means although in the present case the effective magnetic permeability of the solenoid core was lower than expected. Only a small number of turns can be used too maintain reasonably low inductance. This has to be compensated with the use of large currents. In this case, good ventilation must be provided to avoid overheating the electronics. In our case the most temperature sensitive element was the optic fiber transmitter which usually failed after about an hour of operation. Care must also be taken to guarantee balance between the negative and positive pulses as this improves the signal/noise ratio. Finally, we reiterate the need to review the origin and nature of the trigger pulse so that consistent properly clocked data can be acquired. In spite of the unlimited nature of the RFS tests which prevented us from acquiring data suitable for a direct demonstration of the wavefield transform, we did secure high quality wideband data that confirmed the proper performance of the prototype transmitter. We are certain that this equipment can now be used in an oil-field environment to acquire data suitable for a practical verification of the wavefield transform.

  18. Smell testing: an additional tool for identification of adult Refsum's disease

    PubMed Central

    Gibberd, F; Feher, M; Sidey, M; Wierzbicki, A

    2004-01-01

    Objective: To investigate the prevalence and degree of olfactory dysfunction in patients with ARD. Method: The olfactory function of 16 patients with ARD was assessed using the quantitative University of Pennsylvania Smell Identification Test (UPSIT). Results: All patients had complete anosmia or grossly impaired smell function with a mean UPSIT score of 14.7 (SD 4.7) (normal>34) despite having been treated with an appropriate diet for a median of 15 years (range 1–25). Conclusions: Identification of ARD patients can be facilitated by using the UPSIT in combination with the presence of retinitis pigmentosa, even if they have no neurological or bony features. Phytanic acid screening should be performed in any patient manifesting these two signs. PMID:15314127

  19. Additional testing of the inlets designed for a tandem fan V/STOL nacelle

    NASA Technical Reports Server (NTRS)

    Ybarra, A. H.

    1981-01-01

    The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

  20. Influence of compost addition on lead and arsenic bioavailability in reclaimed orchard soil assessed using Porcellio scaber bioaccumulation test.

    PubMed

    Udovic, M; McBride, M B

    2012-02-29

    Long-term application of lead arsenate in orchards has led to a significant accumulation of Pb and As in the topsoil. Reclamation of old orchards for agricultural purposes entails the exposure of humans to Pb and As, which can be reduced by adequate remediation actions. In this study, we assessed the remediation efficiency of compost addition, commonly used as a sustainable agricultural practice, in decreasing the human exposure Pb and As by direct ingestion. The remediation was evaluated based on Pb and As bioavailability, assessed by means of a selective non-exhaustive chemical extraction (modified Morgan extraction, MME), with a physiologically based extraction test (PBET) for the assessment of Pb and As bioavailability in ingested soils and with a novel in vivo bioaccumulation test with isopods (Porcellio scaber). All the tests showed that compost addition consistently reduced Pb, but increased As potential bioavailability. The bioaccumulation test with P. scaber was sensitive to changes in Pb and As bioavailability in test soils. However, the results indicate that the bioavailability of As could be under- or overestimated using solely chemical extraction tests. Indirect assessment of trace metal bioavailability with bioaccumulation in isopods can be used as complementary source of data to the existing in vitro chemical extraction test approach for the estimation of human exposure to trace elements in polluted and remediated soil. This is the first report on the use of As accumulation in P. scaber as a tool for the assessment of As bioavailability in contaminated orchard soil.

  1. Field Operations Program - U.S. Postal Service - Fountain Valley Electric Carrier Route Vehicle Testing

    SciTech Connect

    Francfort, J.E.

    2002-01-21

    The United States Postal Service (USPS) has ordered 500 light-duty electric carrier route vehicles (ECRV) mostly for their delivery carriers to use in several California locations. The 500 ECRVs have been defined as a demonstration fleet to support a decision of potentially ordering 5,500 additional ECRVs. Several different test methods are being used by the USPS to evaluate the 500-vehicle deployment. One of these test methods is the ECRV Customer Acceptance Test Program at Fountain Valley, California. Two newly manufactured ECRVs were delivered to the Fountain Valley Post Office and eighteen mail carriers primarily drove the ECRVs on ''park and loop'' mail delivery routes for a period of 2 days each. This ECRV testing consisted of 36 route tests, 18 tests per vehicle. The 18 mail carriers testing the ECRVs were surveyed for the opinions on the performance of the ECRVs. The U.S. Department of Energy, through its Field Operations Program, is supporting the USPS's ECRV testing activities both financially and with technical expertise. As part of this support, Field Operations Program personnel at the Idaho National Engineering and Environmental Laboratory have compiled this report based on the data generated by the USPS and its testing contractor (Ryerson, Master and Associates, Inc.) During the 36 route tests, the two test vehicles were driven a total of 474 miles, averaging 13 mile per test. The distance of the 36 route tests ranged from 4 to 34 miles. Both miles driven and State-of-Charge (SOC) data was collected for only 28 of the route tests. During these 28 tests, the ECRVs were driven a total of 447 miles. The SOC used during the 28 tests averaged a 41% decrease and the average distance driven was 16 miles. This suggests that a 16-mile route uses almost half of the ECRV's battery energy. The 18 carriers also rated 12 ECRV traits that included the physical design of the ECRVs as well as their performance. Based on a scale of 1 being the lowest and 5 being

  2. Field Operations Program - US Postal Service Fountain Valley Electric Carrier Route Vehicle Testing

    SciTech Connect

    Francfort, James Edward

    2002-01-01

    The United States Postal Service (USPS) has ordered 500 light-duty electric carrier route vehicles (ECRV) mostly for their delivery carriers to use in several California locations. The 500 ECRVs have been defined as a demonstration fleet to support a decision of potentially ordering 5,500 additional ECRVs. Several different test methods are being used by the USPS to evaluate the 500-vehicle deployment. One of these test methods is the ECRV Customer Acceptance Test Program at Fountain Valley, California. Two newly manufactured ECRVs were delivered to the Fountain Valey Post Office and eighteen mail carriers primarily drove the ECRVs on "park and loop" mail delivery routes for a period of 2 days each. This ECRV testing consisted of 36 route tests, 18 tests per vehicle. The 18 mail carriers testing the ECRVs were surveyed for the opinions on the performance of the ECRVs. The U.S. Department of Energy, through its Field Operations Program, is supporting the USPS's ECRV testing activities both financially and with technical expertise. As part of this support, Field Operations Program personnel at the Idaho National Engineering and Environmental Laboratory have compiled this report based on the data generated by the USPS and its testing contractor (Ryerson, Master and Associates, Inc.) During the 36 route tests, the two test vehicles were driven a total of 474 miles, averaging 13 mile per test. The distance of the 36 route tests ranged from 4 to 34 miles. Both miles driven and State-of-Charge (SOC) data was collected for only 28 of the route tests. During these 28 tests, the ECRVs were driven a total of 447 miles. The SOC used during the 28 tests averaged a 41% decrease and the average distance driven was 16 miles. This suggests that a 16-mile route uses almost half of the ECRV's battery energy. The 18 carriers also rated 12 ECRV traits that included the physical design of the ECRVs as well as their performance. Based on a scale of 1 being the lowest and 5 being highest

  3. Semi-empirical equation of limiting current for cobalt electrodeposition in the presence of magnetic field and additive electrolyte

    NASA Astrophysics Data System (ADS)

    Sudibyo, Aziz, N.

    2016-02-01

    One of the available methods to solve a roughening in cobalt electrodeposition is magneto electrodeposition (MED) in the presence of additive electrolyte. Semi-empirical equation of limiting current under a magnetic field for cobalt MED in the presence of boric acid as an additive electrolyte was successfully developed. This semi empirical equation shows the effects of the electrode area (A), the concentration of the electro active species (C), the diffusion coefficient of the electro active species (D), the kinematic viscosity of the electrolyte (v), magnetic strength (B) and the number of electrons involved in the redox process (n). The presence of boric acid led to decrease in the limiting current, but the acid was found useful as a buffer to avoid the local pH rise caused by parallel hydrogen evolution reaction (HER).

  4. Smart Infrared Inspection System Field Operational Test Final Report

    SciTech Connect

    Siekmann, Adam; Capps, Gary J; Franzese, Oscar; Lascurain, Mary Beth

    2011-06-01

    The Smart InfraRed Inspection System (SIRIS) is a tool designed to assist inspectors in determining which vehicles passing through the SIRIS system are in need of further inspection by measuring the thermal data from the wheel components. As a vehicle enters the system, infrared cameras on the road measure temperatures of the brakes, tires, and wheel bearings on both wheel ends of commercial motor vehicles (CMVs) in motion. This thermal data is then presented to enforcement personal inside of the inspection station on a user friendly interface. Vehicles that are suspected to have a violation are automatically alerted to the enforcement staff. The main goal of the SIRIS field operational test (FOT) was to collect data to evaluate the performance of the prototype system and determine the viability of such a system being used for commercial motor vehicle enforcement. From March 2010 to September 2010, ORNL facilitated the SIRIS FOT at the Greene County Inspection Station (IS) in Greeneville, Tennessee. During the course of the FOT, 413 CMVs were given a North American Standard (NAS) Level-1 inspection. Of those 413 CMVs, 384 were subjected to a SIRIS screening. A total of 36 (9.38%) of the vehicles were flagged by SIRIS as having one or more thermal issues; with brakes issues making up 33 (91.67%) of those. Of the 36 vehicles flagged as having thermal issues, 31 (86.11%) were found to have a violation and 30 (83.33%) of those vehicles were placed out-of-service (OOS). Overall the enforcement personnel who have used SIRIS for screening purposes have had positive feedback on the potential of SIRIS. With improvements in detection algorithms and stability, the system will be beneficial to the CMV enforcement community and increase overall trooper productivity by accurately identifying a higher percentage of CMVs to be placed OOS with minimal error. No future evaluation of SIRIS has been deemed necessary and specifications for a production system will soon be drafted.

  5. MAGNET ENGINEERING AND TEST RESULTS OF THE HIGH FIELD MAGNET R AND D PROGRAM AT BNL.

    SciTech Connect

    COZZOLINO,J.; ANERELLA,M.; ESCALLIER,J.; GANETIS,G.; GHOSH,A.; GUPTA,R.; HARRISON,M.; JAIN,A.; MARONE,A.; MURATORE,J.; PARKER,B.; SAMPSON,W.; SOIKA,R.; WANDERER,P.

    2002-08-04

    The Superconducting Magnet Division at Brookhaven National Laboratory (BNL) has been carrying out design, engineering, and technology development of high performance magnets for future accelerators. High Temperature Superconductors (HTS) play a major role in the BNL vision of a few high performance interaction region (IR) magnets that would be placed in a machine about ten years from now. This paper presents the engineering design of a ''react and wind'' Nb{sub 3}Sn magnet that will provide a 12 Tesla background field on HTS coils. In addition, the coil production tooling as well as the most recent 10-turn R&D coil test results will be discussed.

  6. Methods for testing theory and evaluating impact in randomized field trials

    PubMed Central

    Brown, C. Hendricks; Wang, Wei; Kellam, Sheppard G.; Muthén, Bengt O.; Petras, Hanno; Toyinbo, Peter; Poduska, Jeanne; Ialongo, Nicholas; Wyman, Peter A.; Chamberlain, Patricia; Sloboda, Zili; MacKinnon, David P.; Windham, Amy

    2008-01-01

    Randomized field trials provide unique opportunities to examine the effectiveness of an intervention in real world settings and to test and extend both theory of etiology and theory of intervention. These trials are designed not only to test for overall intervention impact but also to examine how impact varies as a function of individual level characteristics, context, and across time. Examination of such variation in impact requires analytical methods that take into account the trial’s multiple nested structure and the evolving changes in outcomes over time. The models that we describe here merge multilevel modeling with growth modeling, allowing for variation in impact to be represented through discrete mixtures—growth mixture models—and nonparametric smooth functions—generalized additive mixed models. These methods are part of an emerging class of multilevel growth mixture models, and we illustrate these with models that examine overall impact and variation in impact. In this paper, we define intent-to-treat analyses in group-randomized multilevel field trials and discuss appropriate ways to identify, examine, and test for variation in impact without inflating the Type I error rate. We describe how to make causal inferences more robust to misspecification of covariates in such analyses and how to summarize and present these interactive intervention effects clearly. Practical strategies for reducing model complexity, checking model fit, and handling missing data are discussed using six randomized field trials to show how these methods may be used across trials randomized at different levels. PMID:18215473

  7. Additive effect of lithium and clonidine with 5-HT1A agonists in the forced swimming test.

    PubMed

    Hascoet, M; Bourin, M; Khimake, S

    1994-03-01

    1. The aim of the present work was to demonstrate the possible additive effect of lithium and clonidine with 5-HT1a agonists in the forced swimming test. 2. Anti-depressant like effects of 5-HT1a agonists was investigated using forced swimming test. When administered alone, only 8-OH-DPAT reduced the immobility time in mice. 3. 5-HT1a agonists were then tested in combination with clonidine or lithium. Only gepirone and ipsapirone pretreated by either lithium or clonidine reduced immobility time in the forced swimming test. 4. The authors conclude that lithium and clonidine might be useful to predict antidepressant-like activity of new compounds.

  8. Field-assisted Densification of Superhard B6O Materials with Y2O3/Al2O3 Addition

    NASA Astrophysics Data System (ADS)

    Herrmann, M.; Raethel, J.; Sempf, K.; Thiele, M.; Bales, A.; Sigalas, I.

    B6O is a possible candidate of superhard materials with a hardness of 45 GPa measured on single crystals. Up to now, densification of these materials was only possible at high pressure. However, recently it was found that different oxides can be utilized as effective sintering additives. In this work the effect of addition of Y2O3/Al2O3 on the densification behaviour as a function of applied pressure, its microstructure evolution, and resulting mechanical properties were investigated. A strong dependence of the densification with increasing pressure was found. The material revealed characteristic triple junctions filled with amorphous residue composed of B2O3, Al2O3 and Y2O3, while no amorphous grain-boundary films were observed along internal interfaces. Mechanical testing revealed on average hardness of 33 GPa, a fracture toughness of 4 MPam1/2, and a strength value of 500 MPa.

  9. Does Field Independence Relate to Performance on Communicative Language Tests?

    ERIC Educational Resources Information Center

    Salmani-Nodoushan, Mohammad Ali

    2006-01-01

    Recent language testing research investigates factors other than language proficiency that may be responsible for systematic variance in language test performance. One such factor is the test takers' cognitive styles. The present study was carried out with the aim of finding the probable effects of Iranian EFL learners' cognitive styles on their…

  10. Comparison Between 30-15 Intermittent Fitness Test and Multistage Field Test on Physiological Responses in Wheelchair Basketball Players

    PubMed Central

    Weissland, Thierry; Faupin, Arnaud; Borel, Benoit; Leprêtre, Pierre-Marie

    2015-01-01

    The intermittent nature of wheelchair court sports suggests using a similar protocol to assess repeated shuttles and recovery abilities. This study aimed to compare performances, physiological responses and perceived rating exertion obtained from the continuous multistage field test (MFT) and the 30-15 intermittent field test (30-15IFT). Eighteen trained wheelchair basketball players (WBP) (WBP: 32.0 ± 5.7 y, IWBF classification: 2.9 ± 1.1 points) performed both incremental field tests in randomized order. Time to exhaustion, maximal rolling velocity (MRV), VO2peak and the peak values of minute ventilation (VEpeak), respiratory frequency (RF) and heart rate (HRpeak) were measured throughout both tests; peak and net blood lactate (Δ[Lact−] = peak–rest values) and perceived rating exertion (RPE) values at the end of each exercise. No significant difference in VO2peak, VEpeak, and RF was found between both tests. 30-15IFT was shorter (12.4 ± 2.4 vs. 14.9 ± 5.1 min, P < 0.05) but induced higher values of MRV and Δ[Lact−] compared to MFT (14.2 ± 1.8 vs. 11.1 ± 1.9 km·h−1 and 8.3 ± 4.2 vs. 6.9 ± 3.3 mmol·L−1, P < 0.05). However, HRpeak and RPE values were higher during MFT than 30-15IFT(172.8 ± 14.0 vs. 166.8 ± 13.8 bpm and 15.3 ± 3.8 vs.13.8 ± 3.5, respectively, P < 0.05). The intermittent shuttles intercepted with rest period occurred during the 30-15IFT could explain a greater anaerobic solicitation. The higher HR and overall RPE values measured at the end of MFT could be explained by its longer duration and a continuous load stress compared to 30-15IFT. In conclusion, 30-15IFT has some advantages over MFT for assess in addition physical fitness and technical performance in WBP. PMID:26733875

  11. Comparison Between 30-15 Intermittent Fitness Test and Multistage Field Test on Physiological Responses in Wheelchair Basketball Players.

    PubMed

    Weissland, Thierry; Faupin, Arnaud; Borel, Benoit; Leprêtre, Pierre-Marie

    2015-01-01

    The intermittent nature of wheelchair court sports suggests using a similar protocol to assess repeated shuttles and recovery abilities. This study aimed to compare performances, physiological responses and perceived rating exertion obtained from the continuous multistage field test (MFT) and the 30-15 intermittent field test (30-15IFT). Eighteen trained wheelchair basketball players (WBP) (WBP: 32.0 ± 5.7 y, IWBF classification: 2.9 ± 1.1 points) performed both incremental field tests in randomized order. Time to exhaustion, maximal rolling velocity (MRV), VO2peak and the peak values of minute ventilation (V Epeak), respiratory frequency (RF) and heart rate (HRpeak) were measured throughout both tests; peak and net blood lactate (Δ[Lact(-)] = peak-rest values) and perceived rating exertion (RPE) values at the end of each exercise. No significant difference in VO2peak, VEpeak, and RF was found between both tests. 30-15IFT was shorter (12.4 ± 2.4 vs. 14.9 ± 5.1 min, P < 0.05) but induced higher values of MRV and Δ[Lact(-)] compared to MFT (14.2 ± 1.8 vs. 11.1 ± 1.9 km·h(-1) and 8.3 ± 4.2 vs. 6.9 ± 3.3 mmol·L(-1), P < 0.05). However, HRpeak and RPE values were higher during MFT than 30-15IFT(172.8 ± 14.0 vs. 166.8 ± 13.8 bpm and 15.3 ± 3.8 vs.13.8 ± 3.5, respectively, P < 0.05). The intermittent shuttles intercepted with rest period occurred during the 30-15IFT could explain a greater anaerobic solicitation. The higher HR and overall RPE values measured at the end of MFT could be explained by its longer duration and a continuous load stress compared to 30-15IFT. In conclusion, 30-15IFT has some advantages over MFT for assess in addition physical fitness and technical performance in WBP. PMID:26733875

  12. Comparison Between 30-15 Intermittent Fitness Test and Multistage Field Test on Physiological Responses in Wheelchair Basketball Players.

    PubMed

    Weissland, Thierry; Faupin, Arnaud; Borel, Benoit; Leprêtre, Pierre-Marie

    2015-01-01

    The intermittent nature of wheelchair court sports suggests using a similar protocol to assess repeated shuttles and recovery abilities. This study aimed to compare performances, physiological responses and perceived rating exertion obtained from the continuous multistage field test (MFT) and the 30-15 intermittent field test (30-15IFT). Eighteen trained wheelchair basketball players (WBP) (WBP: 32.0 ± 5.7 y, IWBF classification: 2.9 ± 1.1 points) performed both incremental field tests in randomized order. Time to exhaustion, maximal rolling velocity (MRV), VO2peak and the peak values of minute ventilation (V Epeak), respiratory frequency (RF) and heart rate (HRpeak) were measured throughout both tests; peak and net blood lactate (Δ[Lact(-)] = peak-rest values) and perceived rating exertion (RPE) values at the end of each exercise. No significant difference in VO2peak, VEpeak, and RF was found between both tests. 30-15IFT was shorter (12.4 ± 2.4 vs. 14.9 ± 5.1 min, P < 0.05) but induced higher values of MRV and Δ[Lact(-)] compared to MFT (14.2 ± 1.8 vs. 11.1 ± 1.9 km·h(-1) and 8.3 ± 4.2 vs. 6.9 ± 3.3 mmol·L(-1), P < 0.05). However, HRpeak and RPE values were higher during MFT than 30-15IFT(172.8 ± 14.0 vs. 166.8 ± 13.8 bpm and 15.3 ± 3.8 vs.13.8 ± 3.5, respectively, P < 0.05). The intermittent shuttles intercepted with rest period occurred during the 30-15IFT could explain a greater anaerobic solicitation. The higher HR and overall RPE values measured at the end of MFT could be explained by its longer duration and a continuous load stress compared to 30-15IFT. In conclusion, 30-15IFT has some advantages over MFT for assess in addition physical fitness and technical performance in WBP.

  13. BOBCAT Personal Radiation Detector Field Test and Evaluation Campaign

    SciTech Connect

    Chris Hodge

    2008-03-01

    Following the success of the Anole test of portable detection system, the U.S. Department of Homeland Security (DHS) Domestic Nuclear Detection Office organized a test and evaluation campaign for personal radiation detectors (PRDs), also known as “Pagers.” This test, “Bobcat,” was conducted from July 17 to August 8, 2006, at the Nevada Test Site. The Bobcat test was designed to evaluate the performance of PRDs under various operational scenarios, such as pedestrian surveying, mobile surveying, cargo container screening, and pedestrian chokepoint monitoring. Under these testing scenarios, many operational characteristics of the PRDs, such as gamma and neutron sensitivities, positive detection and false alarm rates, response delay times, minimum detectable activities, and source localization errors, were analyzed. This paper will present the design, execution, and methodologies used to test this equipment for the DHS.

  14. Personal Radiation Detector Field Test and Evaluation Campaign

    SciTech Connect

    Chris A. Hodge, Ding Yuan, Raymond P. Keegan, Michael A. Krstich

    2007-07-09

    Following the success of the Anole test of portable detection system, the U.S. Department of Homeland Security (DHS) Domestic Nuclear Detection Office organized a test and evaluation campaign for personal radiation detectors (PRDs), also known as 'Pagers'. This test, 'Bobcat', was conducted from July 17 to August 8, 2006, at the Nevada Test Site. The Bobcat test was designed to evaluate the performance of PRDs under various operational scenarios, such as pedestrian surveying, mobile surveying, cargo container screening, and pedestrian chokepoint monitoring. Under these testing scenarios, many operational characteristics of the PRDs, such as gamma and neutron sensitivities, positive detection and false alarm rates, response delay times, minimum detectable activities, and source localization errors, were analyzed. This paper will present the design, execution, and methodologies used to test this equipment for the DHS.

  15. Exercise testing in Warmblood sport horses under field conditions.

    PubMed

    Munsters, Carolien C B M; van Iwaarden, Alexandra; van Weeren, René; Sloet van Oldruitenborgh-Oosterbaan, Marianne M

    2014-10-01

    Regular exercise testing in Warmblood sport horses may, as in racing, potentially help to characterise fitness indices in different disciplines and at various competition levels and assist in understanding when a horse is 'fit to compete'. In this review an overview is given of the current state of the art of exercise testing in the Olympic disciplines of eventing, show jumping and dressage, and areas for further development are defined. In event horses, a simple four-step incremental exercise test measuring heart rate (HR), lactate concentration (LA) and velocity (V) is most often used. In dressage and riding horses, a wide variety of exercise tests have been developed, including incremental exercise tests, indoor riding tests and lunging tests. In show jumping, the use of a five-step incremental exercise test and exercise tests evaluating technical skills and fatigue of the horse has been reported. The velocity at a plasma LA of 4 mmol/L (VLA4) and HR recovery during submaximal exercise intensity have been shown to be the best parameters in event horses for predicting performance and impending injuries. In riding horses, the fitness level of horses is also an important determinant of injuries. Implementation of regular exercise testing and monitoring of training sessions may have important added value in the assessment of performance ability and potential future injuries in Warmblood sport horses. However, there is an urgent need to standardise methodologies and outcome parameters in order to make results comparable.

  16. Sensorimotor Results From a Joint NASA and Russian Pilot Field Test

    NASA Technical Reports Server (NTRS)

    Reschke, Millard F.; Kozlovskaya, Inessa B.

    2016-01-01

    Assessing the full impact of sensorimotor decrements associated with long-duration spaceflight has not been undertaken until 24 hours after landing. To overcome this limitation, both the Russian and U.S. space programs have implemented crew testing at the Soyuz landing site with additional follow-up measurements within 24 hours. Identified as the Pilot Field Test (PFT) this research on NASA’s side included: (1) a sit-to-stand test, (2) recovery from a simulated fall stand test where the crewmember begins in the prone position and then stands for 3.5 minutes while cardiovascular and postural ataxia data are acquired, and (3) a tandem heel-to-toe walk. Video, cardiovascular parameters (heart rate and blood pressure), data from body-worn inertial sensors, and severity of postflight motion sickness were collected during each test session. Russian investigators made measurements associated with: (a) obstacle avoidance, (b) muscle compliance, (c) postural adjustments to perturbations (pushes) applied to the subject’s chest area and (d) center of mass measurements made across most test objectives with insoles inserted into the subjects’ shoes. Data from 18 subjects have been obtained. Additional measurements on functional tests are now being obtained. The increased level of functional deficits not attributable to strength observed in crewmembers has been substantially greater than previously observed when compared with measurements obtained after 24 hours. Full recovery requires 6 to 16 days. Measureable performance parameters such as those associated with functional behaviors are required to provide an evidence base for characterizing programmatic risks for undertaking exploration missions where crewmembers will be unassisted after landing.

  17. Field Lysimeter Test Facility: Protective barrier test results (FY 1990, the third year)

    SciTech Connect

    Campbell, M.D.; Gee, G.W.

    1990-11-01

    The Field Lysimeter Test Facility (FLTF) was constructed to test protective barriers for isolating low-level radioactive and hazardous wastes from the biosphere. Protective barriers are specially configured earth materials placed over near-surface wastes to prevent intrusion of water, plants, and animals. Low-level radioactive waste is stored in near-surface repositories at the Hanford Site and can be transported into the biosphere by water, plants, and animals. The purpose of the FLTF is to measure water balance within barriers as precipitation is partitioned to evaporation (including transpiration), storage, and drainage. Runoff was prevented by raised edges on the lysimeters. Water balance in protective barriers depends on the water-holding capacity of the soil, the gradient of a potential, and the conductivity of the underlying capillary barrier. Current barrier design uses soil with a high water storage capacity and a capillary barrier underlying the soil to increase its water storage capacity. This increased storage capacity is to hold water, which would normally drain, near the the surface where evaporation can cycle it back to the atmosphere. 7 refs., 23 figs., 5 tabs.

  18. TESTING GALACTIC MAGNETIC FIELD MODELS USING NEAR-INFRARED POLARIMETRY

    SciTech Connect

    Pavel, Michael D.; Clemens, D. P.; Pinnick, A. F. E-mail: clemens@bu.edu

    2012-04-10

    This work combines new observations of NIR starlight linear polarimetry with previously simulated observations in order to constrain dynamo models of the Galactic magnetic field. Polarimetric observations were obtained with the Mimir instrument on the Perkins Telescope in Flagstaff, AZ, along a line of constant Galactic longitude (l = 150 Degree-Sign ) with 17 pointings of the 10' Multiplication-Sign 10' field of view between -75 Degree-Sign < b < 10 Degree-Sign , with more frequent pointings toward the Galactic midplane. A total of 10,962 stars were photometrically measured and 1116 had usable polarizations. The observed distribution of polarization position angles with Galactic latitude and the cumulative distribution function of the measured polarizations are compared to predicted values. While the predictions lack the effects of turbulence and are therefore idealized, this comparison allows significant rejection of A0-type magnetic field models. S0 and disk-even halo-odd magnetic field geometries are also rejected by the observations, but at lower significance. New predictions of spiral-type, axisymmetric magnetic fields, when combined with these new NIR observations, constrain the Galactic magnetic field spiral pitch angle to -6 Degree-Sign {+-} 2 Degree-Sign .

  19. Pressure transient testing at Cerro Prieto Geothermal Field

    SciTech Connect

    Rivera, J.R.; Samaniego, F.V.; Schroeder, R.C.

    1980-01-01

    Because of the inherent problems in applying pressure build-up tests to wells producing two-phase fluids, it was decided to use variable flow tests of short duration known as two-rates tests. In these tests of variation in the well flow rates can be used to intepret the transient pressure response in order to determine reservoir parameters such as permeability, well-bore damage and mean reservoir pressure in the well drainage area. Some examples will illustrate the application of this technique. 11 refs.

  20. Field Testing of Energy-Efficient Flood-Damage-Resistant Residential Envelope Systems Summary Report

    SciTech Connect

    Aglan, H.

    2005-08-04

    The primary purpose of the project was to identify materials and methods that will make the envelope of a house flood damage resistant. Flood damage resistant materials and systems are intended to be used to repair houses subsequent to flooding. This project was also intended to develop methods of restoring the envelopes of houses that have been flooded but are repairable and may be subject to future flooding. Then if the house floods again, damage will not be as extensive as in previous flood events and restoration costs and efforts will be minimized. The purpose of the first pair of field tests was to establish a baseline for typical current residential construction practice. The first test modules used materials and systems that were commonly found in residential envelopes throughout the U.S. The purpose of the second pair of field tests was to begin evaluating potential residential envelope materials and systems that were projected to be more flood-damage resistant and restorable than the conventional materials and systems tested in the first pair of tests. The purpose of testing the third slab-on-grade module was to attempt to dry flood proof the module (no floodwater within the structure). If the module could be sealed well enough to prevent water from entering, then this would be an effective method of making the interior materials and systems flood damage resistant. The third crawl space module was tested in the same manner as the previous modules and provided an opportunity to do flood tests of additional residential materials and systems. Another purpose of the project was to develop the methodology to collect representative, measured, reproducible (i.e. scientific) data on how various residential materials and systems respond to flooding conditions so that future recommendations for repairing flood damaged houses could be based on scientific data. An additional benefit of collecting this data is that it will be used in the development of a standard test

  1. Addition of trim coils to the Tandem Mirror Experiment Upgrade (TMX-U) magnet system to improve the magnetic field mapping

    SciTech Connect

    Wong, R.L.; Pedrotti, L.R.; Baldwin, D.E.; Hibbs, S.M.; Hill, D.N.; Hornady, R.H.; Jackson, M.C.

    1985-11-14

    The mapping of the magnetic flux bundle from the center cell to the Plasma Potential Control plates (PPC) on the end fan of the Tandem Mirror Experiment Upgrade (TMX-U), was improved by the addition of trim coils (12,000 amp-turns) on each side of each end fan next to the pump beam magnetic shields. The coils' axes are oriented perpendicular to the machine centerline. These coils made the necessary corrections to the field-line mapping, while keeping the field in the nearby pump beam magnetic shield below the saturation threshold. This paper briefly describes the problem, discusses the design as it evolved, and presents the results of the field testing. The disturbance to the field mapping and the appropriate corrections were determined using the code GFUN (a three dimensional electromagnetic field analysis code that includes the presence of permeable materials). The racetrack-shaped coils have dimensions of 1.5 feet by 3 feet and are powered by a renovated 600 kW Bart-Messing power supply controlled by the machine's magnet control system. The magnets were fabricated from polyimide-coated magnet wire. They are rated to 200/sup 0/C, although in pulsed operation they rise only a few degrees centigrade. The coils are placed outside of the vacuum system, and thus are considerably simpler than the other machine magnets. The restraints are designed to withstand a force of 1000 pounds per coil and a turning moment of 1000 foot pounds. The calculated field strengths were verified on the machine by inserting a Hall probe along the axis. The perturbations to the neutral beam magnetic shields were also measured. A brief description of the improvement in the machine performance is also included.

  2. Radiative corrections to the Higgs boson couplings in the model with an additional real singlet scalar field

    NASA Astrophysics Data System (ADS)

    Kanemura, Shinya; Kikuchi, Mariko; Yagyu, Kei

    2016-06-01

    We calculate renormalized Higgs boson couplings with gauge bosons and fermions at the one-loop level in the model with an additional isospin singlet real scalar field. These coupling constants can deviate from the predictions in the standard model due to tree-level mixing effects and one-loop contributions of the extra neutral scalar boson. We investigate how they can be significant under the theoretical constraints from perturbative unitarity and vacuum stability and also the condition of avoiding the wrong vacuum. Furthermore, comparing with the predictions in the Type I two Higgs doublet model, we numerically demonstrate how the singlet extension model can be distinguished and identified by using precision measurements of the Higgs boson couplings at future collider experiments.

  3. A A field test for extremity dose assessment during outages at Korean nuclear power plants.

    PubMed

    Kim, Hee Geun; Kong, Tae Young

    2013-05-01

    During maintenance on the water chamber of a steam generator, the pressuriser heater and the pressure tube feeder in nuclear power plants, workers are likely to receive high radiation doses due to the severe workplace conditions. In particular, it is expected that workers' hands would receive the highest radiation doses because of their contact with the radioactive materials. In this study, field tests for extremity dose assessments in radiation workers undertaking contact tasks with high radiation doses were conducted during outages at pressurised water reactors and pressurised heavy water reactors in Korea. In the test, the radiation workers were required to wear additional thermoluminescent dosemeters (TLDs) on their backs and wrists and an extremity dosemeter on the finger, as well as a main TLD on the chest while performing the maintenance tasks. PMID:23091221

  4. Field Testing of High Current Electrokinetic Nanoparticle Treatment for Corrosion Mitigation in Reinforced Concrete

    NASA Technical Reports Server (NTRS)

    Cardenas, Henry; Alexander, Joshua; Kupwade-Patil, Kunal; Calle, Luz marina

    2010-01-01

    Electrokinetic Nanoparticle (EN) treatment was used as a rapid repair measure to mitigate chloride induced corrosion of reinforced concrete in the field. EN treatment uses an electric field to transport positively charged nanoparticles to the reinforcement through the concrete capillary pores. Cylindrical reinforced concrete specimens were batched with 4.5 wt % salt content (based on cement mass). Three distinct electrokinetic treatments were conducted using high current density (up to 5 A/m2) to form a chloride penetration barrier that was established in 5 days, as opposed to the traditional 6-8 weeks, generally required for electrochemical chloride extraction (ECE). These treatments included basic EN treatment, EN with additional calcium treatment, and basic ECE treatment. Field exposures were conducted at the NASA Beachside Corrosion Test Site, Kennedy Space Center, Florida, USA. The specimens were subjected to sea water immersion at the test site as a posttreatment exposure. Following a 30-day post-treatment exposure period, the specimens were subjected to indirect tensile testing to evaluate treatment impact. The EN treated specimens exhibited 60% and 30% increases in tensile strength as compared to the untreated controls and ECE treated specimens respectively. The surfaces of the reinforcement bars of the control specimens were 67% covered by corrosion products. In contrast, the EN treated specimens exhibited corrosion coverage of only 4%. Scanning electron microscopy (SEM) revealed a dense concrete microstructure adjacent to the bars of the treated specimens as compared to the control and ECE specimens. Energy dispersive spectroscopic (EDS) analysis of the polished EN treated specimens showed a reduction in chloride content by a factor of 20 adjacent to the bars. This study demonstrated that EN treatment was successful in forming a chloride penetration barrier rapidly. This work also showed that the chloride barrier was effective when samples were exposed to

  5. Field Test Evaluation of Conservation Retrofits of Low-Income, Single-Family Buildings in Wisconsin: Blower-Door-Directed Infiltration Reduction Procedure, Field Test Implementation and Results

    SciTech Connect

    Gettings, M.B.

    2001-05-21

    , and addition of the basic cost of determining the initial leakage rate to the recommended expenditure level. Recommendations for the field test of the procedure include increasing the number of houses in the sample, more timely examination of metered data to detect anomalies, and the monitoring of indoor air temperature. Though not appropriate in a field test of a procedure, further investigation into the effects of air leakage rate reductions on heating loads needs to be performed.

  6. Field Dependence-Independence as a Variable in Second Language Cloze Test Performance.

    ERIC Educational Resources Information Center

    Stansfield, Charles; Hansen, Jacqueline

    1983-01-01

    A study of test performance and field dependent-independent (FD/I) cognitive style in 250 college students showed consistently positive correlation between FI and cloze test scores, and other measures such as final grade. It is suggested cloze tests may call forth cognitive restructuring capabilities more easily for more field independent…

  7. 76 FR 12932 - Availability of an Environmental Assessment for Field Testing Fowl Laryngotracheitis-Marek's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-09

    ..., examines the potential effects that field testing this veterinary vaccine could have on the quality of the... testing this veterinary vaccine will not have a significant impact on the quality of the human environment... Assessment for Field Testing Fowl Laryngotracheitis-Marek's Disease Vaccine, Serotype 3, Live Marek's...

  8. 78 FR 29698 - Availability of an Environmental Assessment for Field Testing a Canine Lymphoma Vaccine, DNA

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-21

    ... a Canine Lymphoma Vaccine, DNA AGENCY: Animal and Plant Health Inspection Service, USDA. ACTION... testing, and then to field test, an unlicensed Canine Lymphoma Vaccine, DNA. The environmental assessment... Lymphoma Vaccine, DNA. Possible Field Test Locations: Arizona, Florida, Georgia, New York, North...

  9. Comparison of field and laboratory-simulated drill-off tests

    SciTech Connect

    Bourdon, J.C.; Peltier, B. ); Cooper, G.A. ); Curry, D.A. ); McCann, D. )

    1989-12-01

    In this paper, field drill-off test results are compared with data from laboratory simulations. A simple theory for analyzing drill-off tests is developed. The weight-on bit (WOB) decay with time is close to exponential, but large threshold WOB's, resulting from poor weight transmission downhole, are sometimes observed in field tests.

  10. Small-scale field tests of attract-and-kill stations for pest Tephritid fruit flies

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Field tests were conducted at UF-TREC, Homestead to test efficacy of wax-matrix bait stations and mass trapping for control of the Caribbean fruit fly in a 5 by 30 tree guava planting. Results of the study and the ability to document control using small-scale field tests will be discussed....

  11. Initial field testing definition of subsurface sealing and backfilling tests in unsaturated tuff; Yucca Mountain Site Characterization Project

    SciTech Connect

    Fernandez, J.A.; Case, J.B.; Tyburski, J.R.

    1993-05-01

    This report contains an initial definition of the field tests proposed for the Yucca Mountain Project repository sealing program. The tests are intended to resolve various performance and emplacement concerns. Examples of concerns to be addressed include achieving selected hydrologic and structural requirements for seals, removing portions of the shaft liner, excavating keyways, emplacing cementitious and earthen seals, reducing the impact of fines on the hydraulic conductivity of fractures, efficient grouting of fracture zones, sealing of exploratory boreholes, and controlling the flow of water by using engineered designs. Ten discrete tests are proposed to address these and other concerns. These tests are divided into two groups: Seal component tests and performance confirmation tests. The seal component tests are thorough small-scale in situ tests, the intermediate-scale borehole seal tests, the fracture grouting tests, the surface backfill tests, and the grouted rock mass tests. The seal system tests are the seepage control tests, the backfill tests, the bulkhead test in the Calico Hills unit, the large-scale shaft seal and shaft fill tests, and the remote borehole sealing tests. The tests are proposed to be performed in six discrete areas, including welded and non-welded environments, primarily located outside the potential repository area. The final selection of sealing tests will depend on the nature of the geologic and hydrologic conditions encountered during the development of the Exploratory Studies Facility and detailed numerical analyses. Tests are likely to be performed both before and after License Application.

  12. ANOLE Portable Radiation Detection System Field Test and Evaluation Campaign

    SciTech Connect

    Chris A. Hodge

    2007-07-12

    Handheld, backpack, and mobile sensors are elements of the Global Nuclear Detection System for the interdiction and control of illicit radiological and nuclear materials. They are used by the U.S. Department of Homeland Security (DHS) and other government agencies and organizations in various roles for border protection, law enforcement, and nonproliferation monitoring. In order to systematically document the operational performance of the common commercial off-the-shelf portable radiation detection systems, the DHS Domestic Nuclear Detection Office conducted a test and evaluation campaign conducted at the Nevada Test Site from January 18 to February 27, 2006. Named “Anole,” it was the first test of its kind in terms of technical design and test complexities. The Anole test results offer users information for selecting appropriate mission-specific portable radiation detection systems. The campaign also offered manufacturers the opportunity to submit their equipment for independent operationally relevant testing to subsequently improve their detector performance. This paper will present the design, execution, and methodologies of the DHS Anole portable radiation detection system test campaign.

  13. Radiation Isotope Identification Device (RIIDs) Field Test and Evaluation Campaign

    SciTech Connect

    Christopher Hodge, Raymond Keegan

    2007-08-01

    Handheld, backpack, and mobile sensors are elements of the Global Nuclear Detection System for the interdiction and control of illicit radiological and nuclear materials. They are used by the U.S. Department of Homeland Security (DHS) and other government agencies and organizations in various roles for border protection, law enforcement, and nonproliferation monitoring. In order to systematically document the operational performance of the common commercial off-the-shelf portable radiation detection systems, the DHS Domestic Nuclear Detection Office conducted a test and evaluation campaign conducted at the Nevada Test Site from January 18 to February 27, 2006. Named 'Anole', it was the first test of its kind in terms of technical design and test complexities. The Anole test results offer users information for selecting appropriate mission-specific portable radiation detection systems. The campaign also offered manufacturers the opportunity to submit their equipment for independent operationally relevant testing to subsequently improve their detector performance. This paper will present the design, execution, and methodologies of the DHS Anole portable radiation detection system test campaign.

  14. Field testing the wildlink capture collar on wolves

    USGS Publications Warehouse

    Mech, L.D.; Gese, E.M.

    1992-01-01

    Seventeen Wildlink capture collars were tested 61 times on 18 gray wolves (Canis lupus) during 1989-1991 in the Superior National Forest of northeastern Minnesota. Overall success rate was 89%, and most failures were attributable to premature battery expiration. When batteries were changed .ltoreq. every 2 months, 17 of 17 tests succeeded. With an upgraded version of the collar in which batteries lasted longer, 17 of 18 tests succeeded. Over the 2-year study, 6 of the 17 collars were lost. For serially recapturing individuals, the Wildlink collar proved useful and reliable if care was taken to replace batteries at proper intervals.

  15. Objectives and first results of the NASA SETI Sky Survey field tests at Goldstone, California

    NASA Technical Reports Server (NTRS)

    Gulkis, S.; Klein, M. J.; Olsen, E. T.; Crow, R. B.; Downs, G. S.

    1985-01-01

    The objectives and preliminary results of the initial field tests of the prototype hardware and software for the NASA SETI program are reviewed with emphasis on the Sky Survey component of the NASA search strategy. In particular, attention is given to field test instrumentation, sky pixelation, sky survey field tests, baseline tests, antenna control tests, and radio frequency interference survey. The test results and observational experience will be used to finalize the design of the SETI Sky Survey processing system and to optimize the observational strategy and procedures in time to begin a full-scale Microwave Observing Program in 1990.

  16. Field test of electric vehicle battery chargers: Customer and utility acceptance: Final report

    SciTech Connect

    Popeck, R.A.; Tolios, K.

    1987-10-01

    A field test was implemented to evaluate the electrical system and customer impacts of recharging up to 10 electric cars. The test was performed in a suburban community during an off-peak electricity demand period. The electrical service in this community is representative of the type of service found throughout the country. The predominant load - electric vehicle battery chargers - contained significant harmonic current distortion. The harmonic distortion was as high as 60%. Voltage distortion was also monitored, and was less than, or equal to 8%. In addition, the power factor of this load was typically less than 80%. Results of a customer response survey indicated that there were no adverse effects on their households' electrical appliances or their personal lifestyles. This report includes a description of the instrumentation suitable for harmonic measurements. Measured harmonic currents and voltages for a single charger and during the field tests are presented. Comparisons are made to existing or proposed harmonic limits for electric systems. 4 refs., 5 figs., 5 tabs.

  17. Mechanical testing and development of the helical field coil joint for the Advanced Toroidal Facility

    SciTech Connect

    Nelson, B.E.; Bryan, W.E.; Goranson, P.L.; Warwick, J.E.

    1985-01-01

    The helical field (HF) coil set for the Advanced Toroidal Facility (ATF) is an M = 12, l = 2, constant-ratio torsatron winding consisting of 2 coils, each with 14 turns of heavy copper conductor. The coils are divided into 24 identical segments to facilitate fabrication and minimize the assembly schedule. The segments are connected across through-bolted lap joints that must carry up to 124,000 A per turn for 5 s or 62,500 A steady-state. In addition, the joints must carry the high magnetic and thermal loads induced in the conductor and still fit within the basic 140- by 30-mm copper envelope. Extensive testing and development were undertaken to verify and refine the basic joint design. Tests included assembly force and clamping force for various types of misalignment; joint resistance as a function of clamping force; clamp bolt relaxation due to thermal cycling; fatigue testing of full-size, multiturn joint prototypes; and low-cycle fatigue and tensile tests of annealed CDA102 copper. The required performance parameters and actual test results, as well as the final joint configuration, are presented. 2 refs., 9 figs., 4 tabs.

  18. SMART Wind Turbine Rotor: Design and Field Test

    SciTech Connect

    Berg, Jonathan C.; Resor, Brian R.; Paquette, Joshua A.; White, Jonathan R.

    2014-01-29

    This report documents the design, fabrication, and testing of the SMART Rotor. This work established hypothetical approaches for integrating active aerodynamic devices (AADs) into the wind turbine structure and controllers.

  19. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... uncertified PTC system, or a product of an uncertified PTC system, or any regression testing of a certified... on-track equipment; (4) An analysis of the applicability of the requirements of subparts A through...

  20. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... uncertified PTC system, or a product of an uncertified PTC system, or any regression testing of a certified... on-track equipment; (4) An analysis of the applicability of the requirements of subparts A through...

  1. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... uncertified PTC system, or a product of an uncertified PTC system, or any regression testing of a certified... on-track equipment; (4) An analysis of the applicability of the requirements of subparts A through...

  2. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... uncertified PTC system, or a product of an uncertified PTC system, or any regression testing of a certified... on-track equipment; (4) An analysis of the applicability of the requirements of subparts A through...

  3. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... uncertified PTC system, or a product of an uncertified PTC system, or any regression testing of a certified... on-track equipment; (4) An analysis of the applicability of the requirements of subparts A through...

  4. Workplace field testing of the pressure drop of particulate respirators using welding fumes.

    PubMed

    Cho, Hyun-Woo; Yoon, Chung-Sik

    2012-10-01

    In a previous study, we concluded that respirator testing with a sodium chloride aerosol gave a conservative estimate of filter penetration for welding fume aerosols. A rapid increase in the pressure drop (PD) of some respirators was observed as fumes accumulated on the filters. The present study evaluated particulate respirator PD based on workplace field tests. A field PD tester was designed and validated using the TSI 8130 Automatic Filter Tester, designed in compliance with National Institute for Occupational and Safety and Health regulation 42 CFR part 84. Three models (two replaceable dual-type filters and one replaceable single-type filter) were evaluated against CO(2) gas arc welding on mild steel in confined booths in the workplace. Field tests were performed under four airborne concentrations (27.5, 15.4, 7.9, and 2.1 mg m(-3)). The mass concentration was measured by the gravimetric method, and number concentration was monitored using P-Trak (Model 8525, TSI, USA). Additionally, photos and scanning electron microscopy-energy dispersive X-ray spectroscopy were used to visualize and analyze the composition of welding fumes trapped in the filters. The field PD tester showed no significant difference compared with the TSI tester. There was no significant difference in the initial PD between laboratory and field results. The PD increased as a function of fume load on the respirator filters for all tested models. The increasing PD trend differed by models, and PD increased rapidly at high concentrations because greater amount of fumes accumulated on the filters in a given time. The increase in PD as a function of fume load on the filters showed a similar pattern as fume load varied for a particular model, but different patterns were observed for different models. Images and elemental analyses of fumes trapped on the respirator filters showed that most welding fumes were trapped within the first layer, outer web cover, and second layer, in order, while no fumes

  5. Workplace field testing of the pressure drop of particulate respirators using welding fumes.

    PubMed

    Cho, Hyun-Woo; Yoon, Chung-Sik

    2012-10-01

    In a previous study, we concluded that respirator testing with a sodium chloride aerosol gave a conservative estimate of filter penetration for welding fume aerosols. A rapid increase in the pressure drop (PD) of some respirators was observed as fumes accumulated on the filters. The present study evaluated particulate respirator PD based on workplace field tests. A field PD tester was designed and validated using the TSI 8130 Automatic Filter Tester, designed in compliance with National Institute for Occupational and Safety and Health regulation 42 CFR part 84. Three models (two replaceable dual-type filters and one replaceable single-type filter) were evaluated against CO(2) gas arc welding on mild steel in confined booths in the workplace. Field tests were performed under four airborne concentrations (27.5, 15.4, 7.9, and 2.1 mg m(-3)). The mass concentration was measured by the gravimetric method, and number concentration was monitored using P-Trak (Model 8525, TSI, USA). Additionally, photos and scanning electron microscopy-energy dispersive X-ray spectroscopy were used to visualize and analyze the composition of welding fumes trapped in the filters. The field PD tester showed no significant difference compared with the TSI tester. There was no significant difference in the initial PD between laboratory and field results. The PD increased as a function of fume load on the respirator filters for all tested models. The increasing PD trend differed by models, and PD increased rapidly at high concentrations because greater amount of fumes accumulated on the filters in a given time. The increase in PD as a function of fume load on the filters showed a similar pattern as fume load varied for a particular model, but different patterns were observed for different models. Images and elemental analyses of fumes trapped on the respirator filters showed that most welding fumes were trapped within the first layer, outer web cover, and second layer, in order, while no fumes

  6. Reverberant Acoustic Testing and Direct Field Acoustic Testing Acoustic Standing Waves and their Impact on Structural Responses

    NASA Technical Reports Server (NTRS)

    Kolaini, Ali R.; Doty, Benjamin; Chang, Zensheu

    2012-01-01

    The aerospace industry has been using two methods of acoustic testing to qualify flight hardware: (1) Reverberant Acoustic Test (RAT), (2) Direct Field Acoustic Test (DFAT). The acoustic field obtained by RAT is generally understood and assumed to be diffuse, expect below Schroeder cut-of frequencies. DFAT method of testing has some distinct advantages over RAT, however the acoustic field characteristics can be strongly affected by test setup such as the speaker layouts, number and location of control microphones and control schemes. In this paper the following are discussed based on DEMO tests performed at APL and JPL: (1) Acoustic wave interference patterns and acoustic standing waves, (2) The structural responses in RAT and DFAT.

  7. CATION TRANSPORT AND PARTITIONING DURING A FIELD TEST OF ELECTROOSMOSIS

    EPA Science Inventory

    Field experiments were conducted to evaluate the effects of soil properties, such as the cation exchange capacity and mineral content, on pH, soluble ion concentrations, and electrical conductivity during electroosmosis in a silty clay soil. The soil is composed mainly of quartz ...

  8. Laboratory and field testing of commercial rotational seismometers

    USGS Publications Warehouse

    Nigbor, R.L.; Evans, J.R.; Hutt, C.R.

    2009-01-01

    There are a small number of commercially available sensors to measure rotational motion in the frequency and amplitude ranges appropriate for earthquake motions on the ground and in structures. However, the performance of these rotational seismometers has not been rigorously and independently tested and characterized for earthquake monitoring purposes as is done for translational strong- and weak-motion seismometers. Quantities such as sensitivity, frequency response, resolution, and linearity are needed for the understanding of recorded rotational data. To address this need, we, with assistance from colleagues in the United States and Taiwan, have been developing performance test methodologies and equipment for rotational seismometers. In this article the performance testing methodologies are applied to samples of a commonly used commercial rotational seismometer, the eentec model R-1. Several examples were obtained for various test sequences in 2006, 2007, and 2008. Performance testing of these sensors consisted of measuring: (1) sensitivity and frequency response; (2) clip level; (3) self noise and resolution; and (4) cross-axis sensitivity, both rotational and translational. These sensor-specific results will assist in understanding the performance envelope of the R-1 rotational seismometer, and the test methodologies can be applied to other rotational seismometers.

  9. Design and Installation of a Disposal Cell Cover Field Test

    SciTech Connect

    Benson, C.H.; Waugh, W.J.; Albright, W.H.; Smith, G.M.; Bush, R.P.

    2011-02-27

    The U.S. Department of Energy’s Office of Legacy Management (LM) initiated a cover assessment project in September 2007 to evaluate an inexpensive approach to enhancing the hydrological performance of final covers for disposal cells. The objective is to accelerate and enhance natural processes that are transforming existing conventional covers, which rely on low-conductivity earthen barriers, into water balance covers, that store water in soil and release it as soil evaporation and plant transpiration. A low conductivity cover could be modified by deliberately blending the upper layers of the cover profile and planting native shrubs. A test facility was constructed at the Grand Junction, Colorado, Disposal Site to evaluate the proposed methodology. The test cover was constructed in two identical sections, each including a large drainage lysimeter. The test cover was constructed with the same design and using the same materials as the existing disposal cell in order to allow for a direct comparison of performance. One test section will be renovated using the proposed method; the other is a control. LM is using the lysimeters to evaluate the effectiveness of the renovation treatment by monitoring hydrologic conditions within the cover profile as well as all water entering and leaving the system. This paper describes the historical experience of final covers employing earthen barrier layers, the design and operation of the lysimeter test facility, testing conducted to characterize the as-built engineering and edaphic properties of the lysimeter soils, the calibration of instruments installed at the test facility, and monitoring data collected since the lysimeters were constructed.

  10. Field test of Ku-band transmission using small-dish (IBS) earth stations

    NASA Astrophysics Data System (ADS)

    Takeuchi, Yoshio; Nohara, Mitsuo; Takahata, Fumio

    A field test of an experimental Intelsat business services (IBS) communications system was conducted for approximately one year to evaluate the transmission quality at the Ku-band before IBS was brought into commercial use in Japan. At first, the configuration of the field test is outlined. Then, the results of the field test are demonstrated and discussed in detail, especially with respect to the bit error rate performance, which specifies the transmission quality of the digital communications.

  11. Some arguments in favor of a Myriophyllum aquaticum growth inhibition test in a water-sediment system as an additional test in risk assessment of herbicides.

    PubMed

    Tunić, Tanja; Knežević, Varja; Kerkez, Đurđa; Tubić, Aleksandra; Šunjka, Dragana; Lazić, Sanja; Brkić, Dragica; Teodorović, Ivana

    2015-09-01

    The present study compares the practicability, reproducibility, power, and sensitivity of a Myriophyllum aquaticum growth inhibition test in a water-sediment system with the recently accepted Myriophyllum spicatum test in an equivalent testing system and the standard Lemna sp. test. Special consideration was given to endpoints based on M. aquaticum control plant growth and variability of relative growth rate and yield: shoot length, fresh weight, dry weight, and root weight. Sensitivity analysis was based on tests performed with 3,5-dichlorophenol, atrazine, isoproturon, trifluralin, 2,4-dichlorophenoloxyacetic acid, and dicamba. Growth rates for average M. aquaticum control plants were 0.119 d(-1) and 0.112 d(-1), with average estimated doubling time 6.33 d and 6.74 d for relative growth rate fresh weight and shoot length, respectively. Intrinsic variability of M. aquaticum endpoints was low: 12.9%, 12.5%, and 17.8% for relative growth rate shoot length, relative growth rate fresh weight and yield fresh weight, respectively. The power of the test was fairly high. When the most sensitive endpoints were used for comparison, the 2 Myriophyllum species were similarly sensitive, more sensitive (in the case of auxin simulators), or at least equally sensitive as Lemna minor to other tested herbicides. The M. aquaticum 10-d test with a 7-d exposure period in a water-sediment system has acceptable sensitivity and can provide repeatable, reliable, and reproducible results; therefore, it should not be disregarded as a good and representative additional test in environmental risk assessment. PMID:25943248

  12. Some arguments in favor of a Myriophyllum aquaticum growth inhibition test in a water-sediment system as an additional test in risk assessment of herbicides.

    PubMed

    Tunić, Tanja; Knežević, Varja; Kerkez, Đurđa; Tubić, Aleksandra; Šunjka, Dragana; Lazić, Sanja; Brkić, Dragica; Teodorović, Ivana

    2015-09-01

    The present study compares the practicability, reproducibility, power, and sensitivity of a Myriophyllum aquaticum growth inhibition test in a water-sediment system with the recently accepted Myriophyllum spicatum test in an equivalent testing system and the standard Lemna sp. test. Special consideration was given to endpoints based on M. aquaticum control plant growth and variability of relative growth rate and yield: shoot length, fresh weight, dry weight, and root weight. Sensitivity analysis was based on tests performed with 3,5-dichlorophenol, atrazine, isoproturon, trifluralin, 2,4-dichlorophenoloxyacetic acid, and dicamba. Growth rates for average M. aquaticum control plants were 0.119 d(-1) and 0.112 d(-1), with average estimated doubling time 6.33 d and 6.74 d for relative growth rate fresh weight and shoot length, respectively. Intrinsic variability of M. aquaticum endpoints was low: 12.9%, 12.5%, and 17.8% for relative growth rate shoot length, relative growth rate fresh weight and yield fresh weight, respectively. The power of the test was fairly high. When the most sensitive endpoints were used for comparison, the 2 Myriophyllum species were similarly sensitive, more sensitive (in the case of auxin simulators), or at least equally sensitive as Lemna minor to other tested herbicides. The M. aquaticum 10-d test with a 7-d exposure period in a water-sediment system has acceptable sensitivity and can provide repeatable, reliable, and reproducible results; therefore, it should not be disregarded as a good and representative additional test in environmental risk assessment.

  13. Field Testing of Compartmentalization Methods for Multifamily Construction

    SciTech Connect

    Ueno, K.; Lstiburek, J.

    2015-03-01

    The 2012 IECC has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure for both single-family and multifamily construction in Climate Zones 3-8. Other programs (LEED, ASHRAE 189, ASHRAE 62.2) have similar or tighter compartmentalization requirements, driving the need for easier and more effective methods of compartmentalization in multifamily buildings. Builders and practitioners have found that fire-resistance rated wall assemblies are a major source of difficulty in air sealing/compartmentalization, particularly in townhouse construction. This problem is exacerbated when garages are “tucked in” to the units and living space is located over the garages. In this project, Building Science Corporation examined the taping of exterior sheathing details to improve air sealing results in townhouse and multifamily construction, when coupled with a better understanding of air leakage pathways. Current approaches are cumbersome, expensive, time consuming, and ineffective; these details were proposed as a more effective and efficient method. The effectiveness of these air sealing methods was tested with blower door testing, including “nulled” or “guarded” testing (adjacent units run at equal test pressure to null out inter-unit air leakage, or “pressure neutralization”). Pressure diagnostics were used to evaluate unit-to-unit connections and series leakage pathways (i.e., air leakage from exterior, into the fire-resistance rated wall assembly, and to the interior).

  14. Characterizing a faulted aquifer by field testing and numerical simulation.

    PubMed

    Allen, D M; Michel, F A

    1999-01-01

    Faulted aquifers constitute one of the most complex geological environments for analysis and interpretation of hydraulic test data because of the inherent ability of faults to act not only as highly transmissive zones but also as hydraulic barriers. Previous studies of the fractured carbonate aquifer at Carleton University, Ottawa, Canada, characterized the flow regime as predominantly linear, but with limited radial nature, and undertook to analyze constant discharge test data using both radial and linear flow models. When used as direct input to a numerical model, the hydraulic parameters, calculated directly from hydraulic test data, were inappropriate and resulted in a poorly calibrated model. While our interpretation of the faulted aquifer remains linear-radial in nature, parameter estimation by numerical simulation highlighted the presence of hydraulic barriers associated with the faults. These barriers are not readily apparent in the constant discharge test data and act to modify the hydraulic test curves at early to mid time, leading to incorrect estimates of the hydraulic parameters. This paper describes the conceptual model and the numerical approach, and demonstrates the importance of using transient simulations for model calibration. PMID:19125925

  15. Numerical modeling of the initial state and matching of well test data from the Zunil geothermal field, Guatemala

    SciTech Connect

    Menzies, A.J.; Granados, E.E.; Sanyal, .K.; Merida-I., L.; Caicedo-A, A.

    1991-01-01

    A significant amount of geoscientific and reservoir engineering data have been collected from the Zunil geothermal field since 1973. The data have been used to define a conceptual model for the field which has formed the basis for the construction of a three dimensional numerical simulation model. The numerical model has successfully matched both the initial state of the reservoir, as indicated by subsurface temperature and pressure distributions within the presently drilled area, and available well test data. The well test data include short and long term discharge tests and a comprehensive pressure interference test. Calibration of the model will continue during 1991 when the results from drilling and testing of three additional deep wells are available. The model will then be used to study various long term production scenarios for the proposed 15 MW power development.

  16. In situ destruction of contaminants via hydrous pyrolysis/oxidation. Visalia Field Test

    SciTech Connect

    Newmark, Robin L.; Aines, Roger D.; Knauss, Kevin; Leif, Roald; Chiarappa, Marina; Hudson, Bryant; Carrigan, Charles; Tompson, Andy; Richards, Jim; Eaker, Craig; Weidner, Randall; Sciarotta, Terry

    1998-12-01

    A field test of hydrous pyrolysis/oxidation (HPO) was conducted during the summer of 1997, during a commercial application of thermal remediation (Dynamic Underground Stripping (DUS)) at the Visalia Pole Yard (a super-fund site) in southern California. At Visalia, Southern California Edison Co. is applying the DUS thermal remediation method to clean up a large (4.3 acre) site contaminated with pole-treating compounds. This is a full-scale cleanup, during which initial extraction of contaminants is augmented by combined steam/air injection in order to enhance the destruction of residual contaminants by HPO. Laboratory results indicate that the contaminants at Visaha react at similar rates to TCE, which has been the focus of extensive laboratory work (Knauss et al., 1998a-c). Field experimental results from this application yield valuable information (1) confirming the destruction of contaminants in soil and groundwater by HPO, (2) validating the predictive models used to design HP0 steam injection systems, (3) demonstrating that accurate field measurements of the critical fluid parameters can be obtained using existing monitoring wells and (4) obtaining a reasonable prediction of the cost and effectiveness of HPO, working at a commercial scale and with commercial partners. The goal of our additional study and demonstration in conjunction with Edison has been to obtain early proof of hydrous pyrolysis/oxidation in the field, and validate our predictive models and monitoring strategies. This demonstration provides valuable economic and practicability data obtained on a commercial scale, with more detailed field validation than is commonly available on a commercially-conducted cleanup. The results of LLNL' s field experiments constrain the destruction rates throughout the site, and enable site management to make accurate estimates of total in situ destruction based on the recovered carbon. As of October, 1998, over 900,000 lb of contaminant have been removed from the

  17. Field testing the prototype BNL fan-atomized oil burner

    SciTech Connect

    McDonald, R.; Celebi, Y.

    1995-04-01

    BNL has developed a new oil burner design referred to as the Fan Atomized burner System. The primary objective of the field study was to evaluate and demonstrate the reliable operation of the Fan Atomized Burner. The secondary objective was to establish and validate the ability of a low firing rate burner (0.3-0.4 gph) to fully satisfy the heating and domestic hot water load demands of an average household in a climate zone with over 5,000 heating-degree-days. The field activity was also used to evaluate the practicality of side-wall venting with the Fan Atomized Burner with a low stack temperature (300F) and illustrate the potential for very high efficiency with an integrated heating system approach based on the Fan Atomized Burner.

  18. Hanle Effect Diagnostics of the Coronal Magnetic Field: A Test Using Realistic Magnetic Field Configurations

    NASA Astrophysics Data System (ADS)

    Raouafi, N.-E.; Solanki, S. K.; Wiegelmann, T.

    2009-06-01

    Our understanding of coronal phenomena, such as coronal plasma thermodynamics, faces a major handicap caused by missing coronal magnetic field measurements. Several lines in the UV wavelength range present suitable sensitivity to determine the coronal magnetic field via the Hanle effect. The latter is a largely unexplored diagnostic of coronal magnetic fields with a very high potential. Here we study the magnitude of the Hanle-effect signal to be expected outside the solar limb due to the Hanle effect in polarized radiation from the H I Lyα and β lines, which are among the brightest lines in the off-limb coronal FUV spectrum. For this purpose we use a magnetic field structure obtained by extrapolating the magnetic field starting from photospheric magnetograms. The diagnostic potential of these lines for determining the coronal magnetic field, as well as their limitations are studied. We show that these lines, in particular H I Lyβ, are useful for such measurements.

  19. Implementing the Mars Science Laboratory Terminal Descent Sensor Field Test Campaign

    NASA Technical Reports Server (NTRS)

    Montgomery, James F.; Bodie, James H.; Brown, Joseph D.; Chen, Allen; Chen, Curtis W.; Essmiller, John C.; Fisher, Charles D.; Goldberg, Hannah R.; Lee, Steven W.; Shaffer, Scott J.

    2012-01-01

    The Mars Science Laboratory (MSL) will deliver a 900 kg rover to the surface of Mars in August 2012. MSL will utilize a new pulse-Doppler landing radar, the Terminal Descent Sensor (TDS). The TDS employs six narrow-beam antennas to provide unprecedented slant range and velocity performance at Mars to enable soft touchdown of the MSL rover using a unique sky crane Entry, De-scent, and Landing (EDL) technique. Prior to use on MSL, the TDS was put through a rigorous verification and validation (V&V) process. A key element of this V&V was operating the TDS over a series of field tests, using flight-like profiles expected during the descent and landing of MSL over Mars-like terrain on Earth. Limits of TDS performance were characterized with additional testing meant to stress operational modes outside of the expected EDL flight profiles. The flight envelope over which the TDS must operate on Mars encompasses such a large range of altitudes and velocities that a variety of venues were neces-sary to cover the test space. These venues included an F/A-18 high performance aircraft, a Eurocopter AS350 AStar helicopter and 100-meter tall Echo Towers at the China Lake Naval Air Warfare Center. Testing was carried out over a five year period from July 2006 to June 2011. TDS performance was shown, in gen-eral, to be excellent over all venues. This paper describes the planning, design, and implementation of the field test campaign plus results and lessons learned.

  20. Additional Reserve Recovery Using New Polymer Treatment on High Water Oil Ratio Wells in Alameda Field, Kingman County, Kansas

    SciTech Connect

    James Spillane

    2005-10-01

    The Chemical Flooding process, like a polymer treatment, as a tertiary (enhanced) oil recovery process can be a very good solution based on the condition of this field and its low cost compared to the drilling of new wells. It is an improved water flooding method in which high molecular-weight (macro-size molecules) and water-soluble polymers are added to the injection water to improve the mobility ratio by enhancing the viscosity of the water and by reducing permeability in invaded zones during the process. In other words, it can improve the sweep efficiency by reducing the water mobility. This polymer treatment can be performed on the same active oil producer well rather than on an injector well in the existence of strong water drive in the formation. Some parameters must be considered before any polymer job is performed such as: formation temperature, permeability, oil gravity and viscosity, location and formation thickness of the well, amount of remaining recoverable oil, fluid levels, well productivity, water oil ratio (WOR) and existence of water drive. This improved oil recovery technique has been used widely and has significant potential to extend reservoir life by increasing the oil production and decreasing the water cut. This new technology has the greatest potential in reservoirs that are moderately heterogeneous, contain moderately viscous oils, and have adverse water-oil mobility ratios. For example, many wells in Kansas's Arbuckle formation had similar treatments and we have seen very effective results. In addition, there were previous polymer treatments conducted by Texaco in Alameda Field on a number of wells throughout the Viola-Simpson formation in the early 70's. Most of the treatments proved to be very successful.

  1. Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

    SciTech Connect

    Bowers, J.S.; Anson, J.R.; Painter, S.M.

    1995-12-31

    Stabilization is a best demonstrated available technology, or BDAT. This technology traps toxic contaminants in a matrix so that they do not leach into the environment. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP the federal leach test) or the Soluble Threshold Leachate Concentration (STLC the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California`s and EPA`s, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. The concentration in the leachate is approximately ten times higher for the STLC procedure than the TCLP. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory (LLNL), additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens) when formulating a stabilization matrix, and they have a neutral pH. By using these clays and additives, LLNL`s highly concentrated wastewater treatment sludges have passed the TCLP and STLC tests. The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements.

  2. Additive effects of glyburide and antidepressants in the forced swimming test: evidence for the involvement of potassium channel blockade.

    PubMed

    Guo, W; Todd, K; Bourin, M; Hascoet, M; Kouadio, F

    1996-08-01

    Evidence in the literature suggests that the modulatory effects of antidepressant drugs (ADS) on neuronal excitability, via the inhibition of K+ channels, may be the final common pathway of pharmacological action. Therefore, we tested the hypothesis that combining the ATP-sensitive K+ channel blocker glyburide with a variety of ADS would produce an additive effect and decrease the immobility time of mice in the forced swimming test (FST). Glyburide (GLY, IP, 30 and 50 mg/kg) and subactive doses of ADS were administered 45 and 30 min, respectively, prior to behavioral testing. Results showed that when combined with GLY, ADS whose main pharmacological effect is one of 5-HT uptake blockade (imipramine, amitriptyline, citalopram, paroxetine, fluoxetine, and fluvoxamine) were more effective in decreasing the amount of time mice were immobile, than when these drugs were administered alone. Some noradrenaline uptake inhibiting ADS (desipramine and viloxazine, but not maprotiline) were also significantly more effective in decreasing immobility time when combined with GLY than when administered alone. Pretreatment with GLY was found to have no effect on the dopamine uptake inhibitor bupropion, and out of the atypical ADS tested (trazodone, mianserine and iprindole), only coadministration with iprindole decreased the immobility time. Only the specific MAO-A inhibitor moclobemide was observed to have an antiimmobility effect when combined with GLY. Neither MAO-B specific (RO 16 6491) nor mixed MAO inhibitors (nialamide and pargyline) interacted with GLY to produce antiimmobility effects. These results corroborate and extend our previous report of the ADS enhancing effects of quinine in the same behavioral model, and suggest that the additive effects of quinine and GLY on ADS in FST are a result of K+ channel blockade.

  3. Field Test of a DHW Distribution System: Temperature and Flow Analyses (Presentation)

    SciTech Connect

    Barley, C. D.; Hendron, B.; Magnusson, L.

    2010-05-13

    This presentation discusses a field test of a DHW distribution system in an occupied townhome. It includes measured fixture flows and temperatures, a tested recirculation system, evaluated disaggregation of flow by measured temperatures, Aquacraft Trace Wizard analysis, and comparison.

  4. Moving from the laboratory to the field: Adding natural environmental conditions to toxicology testing

    EPA Science Inventory

    While laboratory toxicology tests are generally easy to perform, cost effective and readily interpreted, they have been criticized for being unrealistic. In contrast, field tests are considered realistic while producing results that are difficult to interpret and expensive. To ...

  5. Field Testing Stand-Alone Courseware: A Proven Practical Procedure.

    ERIC Educational Resources Information Center

    Westgaard, Odin

    1979-01-01

    Describes procedure to measure a new course's ability to meet standards in three areas: student acceptance, student gains, and student comprehension. It has been used over three years to test the acceptability of 31 courses which contain more than 200 videotape presentations, and thousands of pages of print materials. (Author/JEG)

  6. Robert's Rules for Optimal Learning: Model Development, Field Testing, Implications!

    ERIC Educational Resources Information Center

    McGinty, Robert L.

    The value of accelerated learning techniques developed by the national organization for Suggestive Accelerated Learning Techniques (SALT) was tested in a study using Administrative Policy students taking the capstone course in the Eastern Washington University School of Business. Educators have linked the brain and how it functions to various…

  7. EZVI Injection Field Test Leads to Pilot-Scale Application

    EPA Science Inventory

    Testing and monitoring of emulsified zero-valent ironTM (EZVI) injections was conducted at Cape Canaveral Air Force Station’s Launch Complex 34, FL, in 2002 to 2005 to evaluate the technology’s efficacy in enhancing in situ dehalogenation of dense nonaqueous-phase liquid (DNAPL) ...

  8. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... final amplifier stage, and the AM antenna current or the FM or TV transmitter output power must be...) Purpose, duration and need for the survey. (2) Frequency, transmitter output powers and time of operation..., the power requested shall not exceed that necessary for the purposes of the test. (2) The...

  9. Field Test of an Epidemiology Curriculum for Middle School Students

    ERIC Educational Resources Information Center

    Kaelin, Mark A.; Huebner, Wendy W.; Nicolich, Mark J.; Kimbrough, Maudellyn L.

    2007-01-01

    The purpose of this study was to test the effectiveness of a middle school epidemiology curriculum called Detectives in the Classroom. The curriculum presents epidemiology as the science of public health, using health-related issues that capture the interest of young students and help prepare them to make evidence-based health-related decisions.…

  10. External validity of Concealed Information Test experiment: Comparison of respiration, skin conductance, and heart rate between experimental and field card tests.

    PubMed

    Zaitsu, Wataru

    2016-07-01

    The Concealed Information Test (CIT) is a memory detection method based on an examinee's physiological responses to crime-relevant items (critical items) in comparison with crime-irrelevant items (noncritical items). I examined the external validity of CIT laboratory experiments by comparing respiratory speed (RS), skin conductance response (SCR), and heart rate (HR) between a laboratory experiment (n = 30) and a field test (n = 30) in a card test. A linear mixed models analysis showed that the critical items in both CIT contexts elicited CIT effects: RS repression, SCR increase, and HR deceleration. Additionally, the critical items in the field elicited a larger RS suppression than those in the laboratory; however, SCR and HR on the critical items showed no statistical differences between the laboratory and field CITs. Moreover, the tonic HRs in the field tests were higher than in the CIT experiments, but there were no significant correlations between the tonic HR and each CIT effect in RS, SCR, and HR. These results suggested that CIT detection efficiency was not affected by arousal levels and may imply that the CIT effects observed with RS, SCR, and HR in the CIT laboratory experiments has adequate external validity and can be generalized to the CIT field. PMID:27031043

  11. External validity of Concealed Information Test experiment: Comparison of respiration, skin conductance, and heart rate between experimental and field card tests.

    PubMed

    Zaitsu, Wataru

    2016-07-01

    The Concealed Information Test (CIT) is a memory detection method based on an examinee's physiological responses to crime-relevant items (critical items) in comparison with crime-irrelevant items (noncritical items). I examined the external validity of CIT laboratory experiments by comparing respiratory speed (RS), skin conductance response (SCR), and heart rate (HR) between a laboratory experiment (n = 30) and a field test (n = 30) in a card test. A linear mixed models analysis showed that the critical items in both CIT contexts elicited CIT effects: RS repression, SCR increase, and HR deceleration. Additionally, the critical items in the field elicited a larger RS suppression than those in the laboratory; however, SCR and HR on the critical items showed no statistical differences between the laboratory and field CITs. Moreover, the tonic HRs in the field tests were higher than in the CIT experiments, but there were no significant correlations between the tonic HR and each CIT effect in RS, SCR, and HR. These results suggested that CIT detection efficiency was not affected by arousal levels and may imply that the CIT effects observed with RS, SCR, and HR in the CIT laboratory experiments has adequate external validity and can be generalized to the CIT field.

  12. High SO{sub 2} removal efficiency testing. Topical report - results of sodium formate additive tests at New York State Electric & Gas Corporation`s Kintigh Station

    SciTech Connect

    Murphy, J.

    1997-02-14

    Tests were conducted at New York State Gas & Electric`s (NYSEG`s) Kintigh Station to evaluate options for achieving high sulfur dioxide (SO{sub 2}) removal efficiency in the wet limestone flue gas desulfurization (FGD) system. This test program was one of six conducted by the U.S. Department of Energy to evaluate low-capital-cost upgrades to existing FGD systems as a means for utilities to comply with the requirements of the 1990 Clean Air Act Amendments. The upgrade option tested at Kintigh was sodium formate additive. Results from the tests were used to calibrate the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) to the Kintigh scrubber configuration. FGDPRISM was then used to predict system performance for evaluating conditions other than those tested. An economic evaluation was then done to determine the cost effectiveness of various high-efficiency upgrade options. These costs can be compared with the estimated market value of SO{sub 2} allowance or the expected costs of allowances generated by other means, such as fuel switching or new scrubbers, to arrive at the most cost-effective strategy for Clean Air Act compliance.

  13. CX-100 and TX-100 blade field tests.

    SciTech Connect

    Holman, Adam (USDA-Agriculture Research Service, Bushland, TX); Jones, Perry L.; Zayas, Jose R.

    2005-12-01

    In support of the DOE Low Wind Speed Turbine (LWST) program two of the three Micon 65/13M wind turbines at the USDA Agricultural Research Service (ARS) center in Bushland, Texas will be used to test two sets of experimental blades, the CX-100 and TX-100. The blade aerodynamic and structural characterization, meteorological inflow and wind turbine structural response will be monitored with an array of 75 instruments: 33 to characterize the blades, 15 to characterize the inflow, and 27 to characterize the time-varying state of the turbine. For both tests, data will be sampled at a rate of 30 Hz using the ATLAS II (Accurate GPS Time-Linked Data Acquisition System) data acquisition system. The system features a time-synchronized continuous data stream and telemetered data from the turbine rotor. This paper documents the instruments and infrastructure that have been developed to monitor these blades, turbines and inflow.

  14. A field diagnostic test for the improvised explosive urea nitrate.

    PubMed

    Almog, Joseph; Klein, Asne; Tamiri, Tsippy; Shloosh, Yael; Abramovich-Bar, Sara

    2005-05-01

    A sensitive, specific and simple color test for the improvised explosive urea nitrate is described. It is based on the formation of a red pigment upon the reaction between urea nitrate and p-dimethylaminocinnamaldehyde (p-DMAC) under neutral conditions. Urea itself, which is the starting material for urea nitrate, does not react with p-DMAC under the same conditions. Other potential sources of false positive response e.g., common fertilizers, medications containing the urea moiety and various amines, do not produce the red pigment with p-DMAC. Exhibits collected from 10 terrorist cases have been tested with p-DMAC. The results were in full agreement with those obtained by instrumental techniques including GC/MS, XRD and IR.

  15. Roadside tree/pole crash barrier field test

    NASA Technical Reports Server (NTRS)

    Wilson, A. H.

    1979-01-01

    A series of tests was carried out to evaluate the performance of a crash barrier designed to protect the occupants of an automobile from serious injury. The JPL barrier design is a configuration of empty aluminum beverage cans contained in a tear-resistant bag which, in turn, is encased in a collapsible container made of plywood and steel. Tests were conducted with a driven vehicle impacting the barrier. The basic requirements of NCHRP Report 153 were followed except that speeds of 30 mph rather than 60 mph were used. Accelerometer readings on the driver's helmet showed that the driver was never subjected to dangerous decelerations, and never experienced more than temporary discomfort. Also, all of the requirements of the cited report were met. An extrapolation of data indicated that the JPL barrier installed in front of a tree or telephone pole along a roadside would also have met the requirements at a speed of 40 mph.

  16. Spinning test particles in a Kerr field - I

    NASA Astrophysics Data System (ADS)

    Semerák, O.

    1999-09-01

    Mathisson-Papapetrou equations are solved numerically to obtain trajectories of spinning test particles in (the meridional section of) the Kerr space-time. The supplementary conditions p_σS^μσ=0 are used to close the system of equations. The results show that in principle a spin-curvature interaction may lead to considerable deviations from geodesic motion, although in astrophysical situations of interest probably no large spin effects can be expected for values of spin consistent with a pole-dipole test-particle approximation. However, a significant cumulative effect may occur, e.g. in the inspiral of a spinning particle on to a rotating compact body, that would modify gravitational waves generated by such a system. A thorough literature review is included in the paper.

  17. Cosmological tests of an axiverse-inspired quintessence field

    NASA Astrophysics Data System (ADS)

    Emami, Razieh; Grin, Daniel; Pradler, Josef; Raccanelli, Alvise; Kamionkowski, Marc

    2016-06-01

    Inspired by the string axiverse idea, it has been suggested that the recent transition from decelerated to accelerated cosmic expansion is driven by an axion-like quintessence field with a sub-Planckian decay constant. The scenario requires that the axion field be rather near the maximum of its potential but is less finely tuned than other explanations of cosmic acceleration. The model is parametrized by an axion decay constant f , the axion mass m , and an initial misalignment angle |θi| which is close to π . In order to determine the m and θi values consistent with observations, these parameters are mapped onto observables: the Hubble parameter H (z ) at an angular-diameter distance dA(z ) to redshift z =0.57 , as well as the angular sound horizon of the cosmic microwave background (CMB). Measurements of the baryon acoustic oscillation (BAO) scale at z ≃0.57 by the BOSS survey and Planck measurements of CMB temperature anisotropies are then used to probe the {m ,f ,θi} parameter space. With current data, CMB constraints are the most powerful, allowing a fraction of only ˜0.2 of the parameter-space volume. Measurements of the BAO scale made using the SPHEREx or SKA experiments could go further, observationally distinguishing all but ˜10-2 or ˜10-5 of the parameter-space volume (allowed by simple priors) from the Λ CDM model.

  18. Pressure-interference testing of the Sumikawa geothermal field

    SciTech Connect

    Garg, S.K.; Pritchett, J.W.; Ariki, K.; Kawano, Y.

    1991-01-01

    Pressure interference tests have been used to determine the permeability structure of the Sumikawa reservoir. Interference tests between wells S-4 and KY-1 have indicated the presence of a very high permeability (140 md) north-south channel in the altered andesite layer. Pressure buildup data from well SN-7D have provided indications of a high transmissivity (kh {approx} 18 darcy-meters) reservoir located in the granodiorite layer, lack of pressure response in nearby shutin Sumikawa wells implies that the reservoir penetrated by SN-7D is isolated from the shallower reservoir in the altered andesites. The ''altered andesite'' and the ''granodiorite'' formations constitute the principal geothermal aquifers at Sumikawa. Pressure interference tests (wells KY-1 and SB-2, and wells KY-2 and SB-3) have also confirmed the presence of moderately high transmissivity ({approx} 2 darcy-meters) dacitic layers in the ''marine-volcanic complex'' formation. Because of its low vertical permeability, the ''marine volcanic complex'' formation constitutes an attractive target for the reinjection of waste geothermal fluids.

  19. Field test results of the three-dimensional acquisition and tracking (3DATA) sensor system

    NASA Astrophysics Data System (ADS)

    Fairchild, Paul W.; Lilly, David; Matkin, William B.

    2004-01-01

    Trex has developed two innovative MWIR tracking systems, the Rapid Optical Beam Steering (ROBS) system and the Fast InfraRed Sniper Tracker (FIRST). ROBS was developed by Trex in the mid 1980"s for BMDO and the Navy as a prototype 0.5 meter aperture, wide-angle, multiple target detection, tracking, and imaging system with laser ranging. The smaller FIRST system was developed in the mid 1990"s by Trex for DARPA to acquire and track small caliber bullets. Both systems utilize innovative fast steering methods for achieving very high acceleration rates, ~ 1,000 radians/sec2 for ROBS and ~ 40,000 radians/sec2 for the FIRST system. Each can provide high precision 3D tracking over a large field of regard and both have been demonstrated in field tests. Presently the capabilities of these systems are being expanded. A newer version of the ROBS, 3DATA, is being completed which will provide a capability to precisely track in three dimensions up to 20 targets per second, simultaneously. In addition, an upgraded FIRST system is being designed and built which will handle multiple slow targets in addition to the faster bullets.

  20. Seismic Absorption and Modulus Measurements in Porous Rocks in Lab and Field: Physical, Chemical, and Biological Effects of Fluids (Detecting a Biosurfactant Additive in a Field Irrigation Experiment)

    SciTech Connect

    Spetzler, Hartmut

    2006-05-01

    We have been exploring a new technology that is based on using low-frequency seismic attenuation data to monitor changes in fluid saturation conditions in two-fluid phase porous materials. The seismic attenuation mechanism is related to the loss of energy due to the hysteresis of resistance to meniscus movement (changes in surface tension, wettability) when a pore containing two fluids is stressed at very low frequencies (< 10 Hz). This technology has potential applications to monitoring changes in (1) leakage at buried waste sites, (2) contaminant remediation, and (3) flooding during enhanced petroleum recovery. We have concluded a three year field study at the Maricopa Agricultural Center site of the University of Arizona. Three sets of instruments were installed along an East-West line perpendicular to the 50m by 50m inigation site. Each set of instruments consisted of one three component seismometer and one tiltmeter. Microseisms and solid Earth-tides served as strain sources. The former have a power peak at a period of about 6 seconds and the tides have about two cycles per day. Installation of instruments commenced in late summer of 2002. The instruments operated nearly continuously until April 2005. During the fall of 2003 the site was irrigated with water and one year later with water containing 150 ppm of a biosurfactant additive. This biodegradable additive served to mimic a class of contaminants that change the surface tension of the inigation fluid. Tilt data clearly show tidal tilts superimposed on local tilts due to agricultural irrigation and field work. When the observed signals were correlated with site specific theoretical tilt signals we saw no anomalies for the water irrigation in 2003, but large anomalies on two stations for the surfactant irrigation in 2004. Occasional failures of seismometers as well as data acquisition systems contributed to less than continuous coverage. These data are noisier than the tilt data, but do also show possible

  1. Field Testing of Activated Carbon Injection Options for Mercury Control at TXU's Big Brown Station

    SciTech Connect

    John Pavlish; Jeffrey Thompson; Christopher Martin; Mark Musich; Lucinda Hamre

    2009-01-07

    The primary objective of the project was to evaluate the long-term feasibility of using activated carbon injection (ACI) options to effectively reduce mercury emissions from Texas electric generation plants in which a blend of lignite and subbituminous coal is fired. Field testing of ACI options was performed on one-quarter of Unit 2 at TXU's Big Brown Steam Electric Station. Unit 2 has a design output of 600 MW and burns a blend of 70% Texas Gulf Coast lignite and 30% subbituminous Powder River Basin coal. Big Brown employs a COHPAC configuration, i.e., high air-to-cloth baghouses following cold-side electrostatic precipitators (ESPs), for particulate control. When sorbent injection is added between the ESP and the baghouse, the combined technology is referred to as TOXECON{trademark} and is patented by the Electric Power Research Institute in the United States. Key benefits of the TOXECON configuration include better mass transfer characteristics of a fabric filter compared to an ESP for mercury capture and contamination of only a small percentage of the fly ash with AC. The field testing consisted of a baseline sampling period, a parametric screening of three sorbent injection options, and a month long test with a single mercury control technology. During the baseline sampling, native mercury removal was observed to be less than 10%. Parametric testing was conducted for three sorbent injection options: injection of standard AC alone; injection of an EERC sorbent enhancement additive, SEA4, with ACI; and injection of an EERC enhanced AC. Injection rates were determined for all of the options to achieve the minimum target of 55% mercury removal as well as for higher removals approaching 90%. Some of the higher injection rates were not sustainable because of increased differential pressure across the test baghouse module. After completion of the parametric testing, a month long test was conducted using the enhanced AC at a nominal rate of 1.5 lb/Macf. During the

  2. Vibroacoustic Response of Residential Housing due to Sonic Boom Exposure: A Summary of two Field Tests

    NASA Technical Reports Server (NTRS)

    Klos, Jacob; Buehrle, Ralph; Sullivan, Brenda; Gavin, Joseph; Salamone, Joseph; Haering, Edward A., jr.; Miller, Denise M.

    2008-01-01

    Two experiments have been performed to measure the vibroacoustic response of houses exposed to sonic booms. In 2006, an old home in the base housing area of Edwards Air Force Base, built around 1960 and demolished in 2007, was instrumented with 288 transducers. During a 2007 follow-on test, a newer home in the base housing area, built in 1997, was instrumented with 112 transducers. For each experiment, accelerometers were placed on walls, windows and ceilings in bedrooms of the house to measure the vibration response of the structure. Microphones were placed outside and inside the house to measure the excitation field and resulting interior sound field. The vibroacoustic response of each house was measured for sonic boom amplitudes spanning from 2.4 to 96 Pa (0.05 to 2 lbf/sq ft). The boom amplitudes were systematically varied using a unique dive maneuver of an F/A-18 airplane. In total, the database for both houses contains vibroacoustic response data for 154 sonic booms. In addition, several tests were performed with mechanical shaker excitation of the structure to characterize the forced response of the houses. The purpose of this paper is to summarize all the data from these experiments that are available to the research community, and to compare and contrast the vibroacoustic behavior of these two dissimilar houses.

  3. Field test results of the physical solvent N-Formyl morpholine for gas treating applications

    SciTech Connect

    Palla, N.; Lee, A.L.

    1997-12-31

    The Institute of Gas Technology (IGT) is developing gas processing technology that will reduce gas processing costs for current production and allow subquality gas to be economically produced that would have been otherwise, not produced. The experimental program has primarily focused on the evaluation of N-Formyl Morpholine (NFM) as a physical solvent for the cost-effective upgrading of subquality natural gas to pipeline quality. The selection of NFM for this program was based on previous work conducted by IGT in the selective removal of hydrogen sulfide, and carbon dioxide from coal gasifier effluents. That work showed that the use of NFM resulted in a significant cost advantage over 107 other solvents for that application. The project approach for the development of NFM process has been divided into following main categories: obtain vapor-liquid equilibrium, physical properties and additional published literature data; obtain mass-transfer coefficients using 2 inch absorber/stripper apparatus and calculate equation of state parameters and binary interaction parameters using VLE data; develop a gas processing model using Aspen Plus simulation program and evaluate economic advantages of the NFM process compared to commercial physical solvent; and design a pilot plant skid mounted field test unit and conduct field test experiments.

  4. Interfacial Reactions of Zn-Al Alloys with Na Addition on Cu Substrate During Spreading Test and After Aging Treatments

    NASA Astrophysics Data System (ADS)

    Gancarz, Tomasz; Pstruś, Janusz; Berent, Katarzyna

    2016-08-01

    Spreading tests for Cu substrate with Zn-Al eutectic-based alloys with 0.2, 0.5, and 1.0 wt.% of Na were studied using the sessile drop method in the presence of QJ201 flux. Spreading tests were performed for 1, 3, 8, 15, 30, and 60 min of contact, at the temperatures of 475, 500, 525, and 550 °C. After cleaning the flux residue from solidified samples, the spreading area of Zn-Al + Na on Cu was determined in accordance with ISO 9455-10:2013-03. Selected, solidified solder-substrate couples were cross-sectioned and subjected to scanning electron microscopy of the interfacial microstructure. The experiment was designed to demonstrate the effect of Na addition on the kinetics of formation and growth of CuZn, Cu5Zn8, and CuZn4 phases, which were identified using x-ray diffraction and energy-dispersive spectroscopy analysis. The addition of Na to eutectic Zn-Al caused the spreading area to decrease and the thickness of intermetallic compound layers at the interface to reduce. Samples after the spreading test at 500 °C for 1 min were subjected to aging for 1, 10, and 30 days at 120,170, and 250 °C. The greater thicknesses of IMC layers were obtained for a temperature of 250 °C. With increasing Na content in Zn-Al + Na alloys, the thickness reduced, which correlates to the highest value of activation energy for Zn-Al with 1% Na.

  5. Interfacial Reactions of Zn-Al Alloys with Na Addition on Cu Substrate During Spreading Test and After Aging Treatments

    NASA Astrophysics Data System (ADS)

    Gancarz, Tomasz; Pstruś, Janusz; Berent, Katarzyna

    2016-04-01

    Spreading tests for Cu substrate with Zn-Al eutectic-based alloys with 0.2, 0.5, and 1.0 wt.% of Na were studied using the sessile drop method in the presence of QJ201 flux. Spreading tests were performed for 1, 3, 8, 15, 30, and 60 min of contact, at the temperatures of 475, 500, 525, and 550 °C. After cleaning the flux residue from solidified samples, the spreading area of Zn-Al + Na on Cu was determined in accordance with ISO 9455-10:2013-03. Selected, solidified solder-substrate couples were cross-sectioned and subjected to scanning electron microscopy of the interfacial microstructure. The experiment was designed to demonstrate the effect of Na addition on the kinetics of formation and growth of CuZn, Cu5Zn8, and CuZn4 phases, which were identified using x-ray diffraction and energy-dispersive spectroscopy analysis. The addition of Na to eutectic Zn-Al caused the spreading area to decrease and the thickness of intermetallic compound layers at the interface to reduce. Samples after the spreading test at 500 °C for 1 min were subjected to aging for 1, 10, and 30 days at 120,170, and 250 °C. The greater thicknesses of IMC layers were obtained for a temperature of 250 °C. With increasing Na content in Zn-Al + Na alloys, the thickness reduced, which correlates to the highest value of activation energy for Zn-Al with 1% Na.

  6. Exploration 3-D Seismic Field Test/Native Tribes Initiative

    SciTech Connect

    Carroll, Herbert B.; Chen, K.C.; Guo, Genliang; Johnson, W.I.; Reeves,T.K.; Sharma,Bijon

    1999-04-27

    To determine current acquisition procedures and costs and to further the goals of the President's Initiative for Native Tribes, a seismic-survey project is to be conducted on Osage tribal lands. The goals of the program are to demonstrate the capabilities, costs, and effectiveness of 3-D seismic work in a small-operator setting and to determine the economics of such a survey. For these purposes, typical small-scale independent-operator practices are being followed and a shallow target chose in an area with a high concentration of independent operators. The results will be analyzed in detail to determine if there are improvements and/or innovations which can be easily introduced in field-acquisition procedures, in processing, or in data manipulation and interpretation to further reduce operating costs and to make the system still more active to the small-scale operator.

  7. Testing the Need for Replication of Eddy Covariance Carbon Dioxide Flux Measurements over Agricultural Fields

    NASA Astrophysics Data System (ADS)

    Taylor, A. M.; Amiro, B. D.; Gervais, M.

    2015-12-01

    The eddy covariance method directly measures carbon dioxide (CO2) fluxes for long periods of time and with footprints up to hundreds of meters in size. Any ecosystem process that alters how gases and energy move between the atmosphere and soil/vegetation can affect these fluxes. Eddy covariance is vulnerable to systematic errors and uncertainy, particular through relying on assumptions about surface characteristics. Additionally, spatial variation within a site can cause more uncertainty in these measurements and lack of replication in many eddy covariance studies makes statistical analysis of carbon fluxes challenging. We tested if there are significant differences between co-located and simultaneous CO2 flux measurements over a uniform crop surface, and if the differences increase if we measure different flux footprint areas over the same field. During the summer of 2014, three matched instrumented 2.5-m high towers were co-located and then periodically separated by moving at 50 m intervals along a north-south transect on an alfalfa/trefoil field and a spring wheat field in Southern Manitoba, Canada to compare CO­2 fluxes. Georeferenced leaf area index measurements were taken in 50 m grid of each field to establish uniformity of the source/sink within a footprint. Diurnal differences of similar magnitude in the CO2 ­fluxes were found in both the co-located experiment and the spatially separated intervals. Despite rigorous calibration during the experiment, some differences were caused by the measurement systems rather than by variation within the field. Interpretation of the spatial variation in leaf area index is being used to determine the contribution caused by difference in source/sink contributions to the flux footprint areas when the towers were spatially separated.

  8. Field Testing of Compartmentalization Methods for Multifamily Construction

    SciTech Connect

    Ueno, K.; Lstiburek, J. W.

    2015-03-01

    The 2012 International Energy Conservation Code (IECC) has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure (3 ACH50) for single-family and multifamily construction (in climate zones 3–8). The Leadership in Energy & Environmental Design certification program and ASHRAE Standard 189 have comparable compartmentalization requirements. ASHRAE Standard 62.2 will soon be responsible for all multifamily ventilation requirements (low rise and high rise); it has an exceptionally stringent compartmentalization requirement. These code and program requirements are driving the need for easier and more effective methods of compartmentalization in multifamily buildings.

  9. Land reclamation on the Nevada Test Site: A field tour

    SciTech Connect

    Winkel, V.K.; Ostler, W.K.

    1993-12-31

    An all-day tour to observe and land reclamation on the Nevada Test Site was conducted in conjunction with the 8th Wildland Shrub and Arid Land Restoration Symposium. Tour participants were introduced to the US Department of Energy reclamation programs for Yucca Mountain Site Characterization Project and Treatability Studies for Soil Media (TSSM) Project. The tour consisted of several stops that covered a variety of topics and studies including revegetation by seeding, topsoil stockpile stabilization, erosion control, shrub transplanting, shrub herbivory, irrigation, mulching, water harvesting, and weather monitoring.

  10. Sensorimotor Results from the Joint NASA and Russian Pilot Field Test

    NASA Technical Reports Server (NTRS)

    Reschke, Millard; Kozlovskaya, I. B.; Kofman, I. S.; Tomilovskaya, E. S.; Cerisano, J. M.; Bloomberg, J. J.; Stenger, M. B.; Lee, S. M. C.; Laurie, S. S.; Rukavishnikov, I. V.; Fomina, E. V.; Wood, S. J.; Mulavara, A. P.; Feiveson, A. H.; Fisher, E. A.; Rosenberg, M. J. F.; Kitov, V. V.; Lysova, N. Yu

    2016-01-01

    Testing of crew responses following long-duration flights has not previously been possible until a minimum of 24 hours after landing. As a result, it has not been possible to estimate the nonlinear trend of the early (<24 hours) recovery process, nor has it been possible to accurately assess the full impact of the decrements associated with long-duration flight. To overcome these limitations, both the Russian and U.S. programs have implemented testing at the Soyuz landing site. This research effort has been identified as the Field Test (FT). For operational reasons the FT has been divided into two phases: the full FT and a preliminary pilot version (PFT) of the FT that is reduced in both length and scope. The PFT has now been completed with the landing of the crew of International Space Station Increment 42/43 (Soyuz expedition 41S). RESEARCH: The primary goal of this research was to determine functional abilities associated with long-duration space flight crews beginning as soon after landing as possible (< 2 hours) with an additional two follow-up measurement sessions within 24 hours after landing. This study goal has both sensorimotor and cardiovascular elements. The PFT represented a initial evaluation of the feasibility of testing in the field and was comprised of a jointly agreed upon subset of tests drawn from the full FT and relied heavily on Russia's Institute of Biomedical Problems Sensory-Motor and Countermeasures Department for content and implementation. Data from the PFT was collected following several ISS missions. Testing on the U.S. side has included: (1) a sit-to-stand test, (2) recovery from a fall stand test where the crewmember begins in the prone position on the ground and then stands for 3.5 minutes while cardiovascular performance and postural ataxia data are acquired, and (3) a tandem heel-to-toe walk test to determine changes in the central locomotor program. Video, cardiovascular parameters (heart rate and blood pressure), data from body

  11. High SO{sub 2} removal efficiency testing: Results of DBA and sodium formate additive tests at Southwestern Electric Power company`s Pirkey Station

    SciTech Connect

    1996-05-30

    Tests were conducted at Southwestern Electric Power Company`s (SWEPCo) Henry W. Pirkey Station wet limestone flue gas desulfurization (FGD) system to evaluate options for achieving high sulfur dioxide removal efficiency. The Pirkey FGD system includes four absorber modules, each with dual slurry recirculation loops and with a perforated plate tray in the upper loop. The options tested involved the use of dibasic acid (DBA) or sodium formate as a performance additive. The effectiveness of other potential options was simulated with the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) after it was calibrated to the system. An economic analysis was done to determine the cost effectiveness of the high-efficiency options. Results are-summarized below.

  12. Second Field Test of the AEL Measure of School Capacity for Improvement

    ERIC Educational Resources Information Center

    Copley, Lisa D.; Meehan, Merrill L.; Howley, Caitlin W.; Hughes, Georgia K.

    2005-01-01

    The major purpose of the second field test of the AEL MSCI instrument was to assess the psychometric properties of the refined version with a larger, more diverse group of respondents. The first objective of this field test was to expand the four-point Likert-type response scale to six points in order to yield more variance in responses. The…

  13. 40 CFR 35.2211 - Field testing for Innovative and Alternative Technology Report.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Field testing for Innovative and Alternative Technology Report. 35.2211 Section 35.2211 Protection of Environment ENVIRONMENTAL PROTECTION... Treatment Works § 35.2211 Field testing for Innovative and Alternative Technology Report. The grantee...

  14. 40 CFR 35.2211 - Field testing for Innovative and Alternative Technology Report.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Field testing for Innovative and Alternative Technology Report. 35.2211 Section 35.2211 Protection of Environment ENVIRONMENTAL PROTECTION... Treatment Works § 35.2211 Field testing for Innovative and Alternative Technology Report. The grantee...

  15. Training Probation and Parole Officers to Provide Substance Abuse Treatment: A Field Test.

    ERIC Educational Resources Information Center

    Cunningham, John A.; Herie, Marilyn; Martin, Garth; Turner, Bonnie J.

    1998-01-01

    The results of field-testing a substance-abuse treatment protocol are reported. Ten probation and parole officers were trained in Structured Relapse Prevention, and 55 clients were treated. Incentives and barriers to treatment are highlighted. The use of this type of field test as a dissemination technique is discussed. (EMK)

  16. The Major Field Test in Business: A Solution to the Problem of Assurance of Learning Assessment?

    ERIC Educational Resources Information Center

    Green, Jeffrey J.; Stone, Courtenay Clifford; Zegeye, Abera

    2014-01-01

    Colleges and universities are being asked by numerous sources to provide assurance of learning assessments of their students and programs. Colleges of business have responded by using a plethora of assessment tools, including the Major Field Test in Business. In this article, the authors show that the use of the Major Field Test in Business for…

  17. 78 FR 58514 - Availability of an Environmental Assessment for Field Testing of a DNA Immunostimulant

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... of a DNA Immunostimulant AGENCY: Animal and Plant Health Inspection Service, USDA. ACTION: Notice of... then to field test, an unlicensed DNA Immunostimulant recommended for reduction in morbidity and.... Product: DNA Immunostimulant. Possible Field Test Locations: Texas, Mississippi, and Georgia for...

  18. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CFR part 1065, subpart J, we describe the equipment and sampling methods for testing engines in the field. Use fuel meeting the specifications of 40 CFR part 1065, subpart H, or a fuel typical of what you... 40 Protection of Environment 33 2011-07-01 2011-07-01 false What are the field-testing...

  19. Multibar sawless lint cleaner: fiber quality analysis after 3rd year of field testing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    After two years of field testing a prototype spiked-tooth lint cleaner, the Multibar Sawless Lint Cleaner (MBSLC), a final year of field evaluation was conducted at commercial cotton gin in West Texas located approximately 30 miles Southwest of Lubbock, Texas.The cotton lint cleaner was tested in a ...

  20. 40 CFR 35.2211 - Field testing for Innovative and Alternative Technology Report.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Field testing for Innovative and Alternative Technology Report. 35.2211 Section 35.2211 Protection of Environment ENVIRONMENTAL PROTECTION... Treatment Works § 35.2211 Field testing for Innovative and Alternative Technology Report. The grantee...