Science.gov

Sample records for additional field tests

  1. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

    SciTech Connect

    Gary M. Blythe

    2006-03-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, ''Field Testing of a Wet FGD Additive.'' The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemissions of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate that the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project will conduct pilot and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosage requirements to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB co-fired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot and full-scale jet bubbling reactor (JBR) FGD systems to be tested. A third utility, to be named later, will provide the high-sulfur Eastern bituminous coal full-scale FGD test site. Degussa Corporation is providing the TMT-15 additive and technical support to the test program. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in

  2. Acceptance test report: Field test of mixer pump for 241-AN-107 caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1997-05-16

    The field acceptance test of a 75 HP mixer pump (Hazleton serial number N-20801) installed in Tank 241-AN-107 was conducted from October 1995 thru February 1996. The objectives defined in the acceptance test were successfully met, with two exceptions recorded. The acceptance test encompassed field verification of mixer pump turntable rotation set-up and operation, verification that the pump instrumentation functions within established limits, facilitation of baseline data collection from the mixer pump mounted ultrasonic instrumentation, verification of mixer pump water flush system operation and validation of a procedure for its operation, and several brief test runs (bump) of the mixer pump.

  3. Field Testing of a Wet FGD Additive for Enhanced Mercury Control

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-31

    This document is the final report for DOE-NETL Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project has been to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project was intended to demonstrate whether such additives can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project involved pilot- and full-scale tests of the additives in wet FGD absorbers. The tests were intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power provided the Texas lignite/PRB co-fired test site for pilot FGD tests and project cost sharing. Southern Company provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested, and project cost sharing. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation provided the TMT-15 additive, and the Nalco Company provided the Nalco 8034 additive. Both companies also supplied technical support to the test program as in-kind cost sharing. The project was conducted in six tasks. Of the six tasks, Task 1 involved project planning and Task 6 involved

  4. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    SciTech Connect

    Gary Blythe

    2007-05-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing

  5. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the additives in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power has provided the Texas lignite/PRB co-fired test site for pilot FGD tests and cost sharing. Southern Company has provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation is providing the TMT-15 additive, and the Nalco Company is providing the Nalco 8034 additive. Both companies are also supplying technical support to the test program as in-kind cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management

  6. Testing the Addition of Topographic Features for Field Scale Infiltration Excess Water Quality Modeling in SWAT

    NASA Astrophysics Data System (ADS)

    Collick, A.; Easton, Z. M.; Kleinman, P. J. A.; Sommerlot, A.; White, M. J.; Harmel, D.; Fuka, D.

    2014-12-01

    Watershed planners and managers need reliable tools that can capture the spatial and temporal complexity of agricultural landscapes, and water quality models are increasingly relied upon to represent P loss from agricultural watersheds. While a significant amount of modeling work has attempted to incorporate factors controlling P loss (e.g. representing solubility, manure types, timing and application type), these models still typically require significant calibration and are thus difficult to apply meaningfully in areas without copious data with which to calibrate. This is partially because these models were never really intended as field scale tools, while we are trying to use them to define different hydrologic pathways, area weighted potential energy (slopes and saturated conductivities), and the resulting lag time of P in different transport states. The movement of water within the landscape as surface (or near-surface) storm runoff and interflow is driven by gravity, topography, contributing area and soil and landuse characteristics, which play roles in concentrating water flows. Soil surveys have played a key role in the development of pedology and spatially derived pedon soil maps have become valuable datasets for natural resource management. Unfortunately, the soil surveys, commonly available at ~1:20,000 scale, are not designed to provide the high-resolution models of the soil continuum required in field scale environmental modeling applications and site specific crop and water quality management. The goal of this project is to test a methodology designed initially for representing saturation excess hydrology in the SWAT model to incorporate topographic attributes, and resulting spatially explicit soil morphology, that are missing from standard SWAT model initializations.

  7. An Additive Manufacturing Test Artifact

    PubMed Central

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  8. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system.

  9. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  10. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  11. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  12. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  13. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  14. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  15. 78 FR 22209 - Additional Synthetic Drug Testing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-15

    ... COMMISSION 10 CFR Part 26 Additional Synthetic Drug Testing AGENCY: Nuclear Regulatory Commission. ACTION... NRC amend its Fitness for Duty program regulations to amend drug testing requirements to test for additional synthetic drugs currently not included in the regulations. The NRC determined that the...

  16. Mobilestar field test program

    NASA Technical Reports Server (NTRS)

    Rubow, Wayne

    1988-01-01

    Various field tests were performed in order to gain practical experience and a broader understanding of mobile communications. The first phase consisted of CW propagation tests to develop firsthand experience of propagation phenomena. From this information, estimates of the feasibility and accuracy of power control were possible. The next phase tested the idea of power control. Equipment representative of that expected to be used in an actual mobile satellite communication system was assembled and tested under a variety of environments.

  17. Pilot Field Test Study

    NASA Technical Reports Server (NTRS)

    Sherriff, Abigail

    2015-01-01

    The Field Test study is currently in full swing, preceded by the successful completion of the Pilot Field Test study that paved the way for collecting data on the astronauts in the medical tent in Kazakhstan. Abigail Sherriff worked alongside Logan Dobbe on one Field Test aspect to determine foot clearance over obstacles (5cm, 10cm, and 15cm) using APDM Inc. Internal Measurement Units (IMU) worn by the astronauts. They created a program to accurately calculate foot clearance using the accelerometer, magnetometer, and gyroscope data with the IMUs attached to the top of the shoes. To validate the functionality of their program, they completed a successful study on test subjects performing various tasks in an optical motion studio, considered a gold standard in biomechanics research. Future work will include further validation and expanding the program to include other analyses.

  18. FSA field test

    NASA Technical Reports Server (NTRS)

    Jaffe, P.; Weaver, R. W.; Lee, R. E.

    1981-01-01

    The 12 continental remote sites were decommissioned. Testing was consolidated into a five-site network consisting of the four Southern California sites and a new Florida site. 16 kW of new state-of-the-art modules were deployed at the five sites. Testing of the old modules continued at the Goldstone site but as a low-priority item. Array testing of modules is considered. Additional new testing capabilities were added. A battery-powered array data logger is discussed. A final set of failure and degradation data was obtained from the modules.

  19. FSA field test

    NASA Astrophysics Data System (ADS)

    Jaffe, P.; Weaver, R. W.; Lee, R. E.

    1981-12-01

    The 12 continental remote sites were decommissioned. Testing was consolidated into a five-site network consisting of the four Southern California sites and a new Florida site. 16 kW of new state-of-the-art modules were deployed at the five sites. Testing of the old modules continued at the Goldstone site but as a low-priority item. Array testing of modules is considered. Additional new testing capabilities were added. A battery-powered array data logger is discussed. A final set of failure and degradation data was obtained from the modules.

  20. Direct Field Acoustic Testing

    NASA Technical Reports Server (NTRS)

    Larkin, Paul; Goldstein, Bob

    2008-01-01

    This paper presents an update to the methods and procedures used in Direct Field Acoustic Testing (DFAT). The paper will discuss some of the recent techniques and developments that are currently being used and the future publication of a reference standard. Acoustic testing using commercial sound system components is becoming a popular and cost effective way of generating a required acoustic test environment both in and out of a reverberant chamber. This paper will present the DFAT test method, the usual setup and procedure and the development and use of a closed-loop, narrow-band control system. Narrow-band control of the acoustic PSD allows all standard techniques and procedures currently used in random control to be applied to acoustics and some examples are given. The paper will conclude with a summary of the development of a standard practice guideline that is hoped to be available in the first quarter of next year.

  1. The teratology testing of food additives.

    PubMed

    Barrow, Paul C; Spézia, François

    2013-01-01

    The developmental and reproductive toxicity testing (including teratogenicity) of new foods and food additives is performed worldwide according to the guidelines given in the FDA Redbook. These studies are not required for substances that are generally recognized as safe, according to the FDA inventory. The anticipated cumulated human exposure level above which developmental or reproduction studies are required depends on the structure-alert category. For food additives of concern, both developmental (prenatal) and reproduction (multigeneration) studies are required. The developmental studies are performed in two species, usually the rat and the rabbit. The reproduction study is generally performed in the rat. The two rat studies are preferably combined into a single experimental design, if possible. The test methods described in the FDA Redbook are similar to those specified by the OECD for the reproductive toxicity testing of chemicals.

  2. Laboratory tests of sludge-control additives

    SciTech Connect

    Tatnall, R.E.

    1996-07-01

    Laboratory {open_quotes}jar{close_quotes} tests compared eleven different fuel oil and diesel fuel sludge-control additives. Factors studied included (1) ability to disperse and prevent buildup of sludge deposits on surfaces, (2) ability to protect steel from corrosion, (3) ability to inhibit growth and proliferation of bacteria, and (4) ability to disperse water. Results varied greatly, and it was found that many commercial products do not do what they claim. It is concluded that fuel retailers should not believe manufacturers` claims for their additive products, but rather should test such products themselves to be sure that the benefits of treatment are real. A simplified form of the procedure used here is proposed as one way for dealers to do such testing.

  3. RESOLVE 2010 Field Test

    NASA Technical Reports Server (NTRS)

    Captain, J.; Quinn, J.; Moss, T.; Weis, K.

    2010-01-01

    This slide presentation reviews the field tests conducted in 2010 of the Regolith Environment Science & Oxygen & Lunar Volatile Extraction (RESOLVE). The Resolve program consist of several mechanism: (1) Excavation and Bulk Regolith Characterization (EBRC) which is designed to act as a drill and crusher, (2) Regolith Volatiles Characterization (RVC) which is a reactor and does gas analysis,(3) Lunar Water Resources Demonstration (LWRD) which is a fluid system, water and hydrogen capture device and (4) the Rover. The scientific goal of this test is to demonstrate evolution of low levels of hydrogen and water as a function of temperature. The Engineering goals of this test are to demonstrate:(1) Integration onto new rover (2) Miniaturization of electronics rack (3) Operation from battery packs (elimination of generator) (4) Remote command/control and (5) Operation while roving. Views of the 2008 and the 2010 mechanisms, a overhead view of the mission path, a view of the terrain, the two drill sites, and a graphic of the Master Events Controller Graphical User Interface (MEC GUI) are shown. There are descriptions of the Gas chromatography (GC), the operational procedure, water and hydrogen doping of tephra. There is also a review of some of the results, and future direction for research and tests.

  4. Feasibility and Testing of Additive Manufactured Components

    SciTech Connect

    Dehoff, Ryan R.; Hummelt, Ed; Solovyeva, Lyudmila

    2016-09-01

    This project focused on demonstrating the ability to fabricate two parts with different geometry: an arc flash interrupter and a hydraulic manifold. Eaton Corporation provided ORNL solid models, information related to tolerances and sensitive parameters of the parts and provided testing and evaluation. ORNL successfully manufactured both components, provided cost models of the manufacturing (materials, labor, time and post processing) and delivered test components for Eaton evaluation. The arc flash suppressor was fabricated using the Renishaw laser powder bed technology in CoCrMo while the manifold was produced from Ti-6Al-4V using the Arcam electron beam melting technology. These manufacturing techniques were selected based on the design and geometrical tolerances required. A full-scale manifold was produced on the Arcam A2 system (nearly 12 inches tall). A portion of the manifold was also produced in the Arcam Q10 system. Although a full scale manifold could not be produced in the system, a full scale manifold is expected to have similar material properties, geometric accuracy, and surface finish as could be fabricated on an Arcam Q20 system that is capable of producing four full scale manifolds in a production environment. In addition to the manifold, mechanical test specimens, geometric tolerance artifacts, and microstructure samples were produced alongside the manifold. The development and demonstration of these two key components helped Eaton understand the impact additive manufacturing can have on many of their existing products. By working within the MDF and leveraging ORNL’s manufacturing and characterization capabilities, the work will ensure the rapid insertion and commercialization of this technology.

  5. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  6. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  7. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  8. LSA field test

    NASA Technical Reports Server (NTRS)

    Jaffe, P.

    1980-01-01

    After almost four years of endurance testing of photovoltaic modules, no fundamental life-limiting mechanisms were identified that could prevent the twenty-year life goal from being met. The endure data show a continual decline in the failure rate with each new large-scale procurement. Cracked cells and broken interconnects continue to be the principal causes of failure. Although the modules are more adversely affected physically by hot, humid environments than by cool or dry environments there are insufficient data to correlate failure with environment. There is little connection between the outward physical condition of a module and changes in its electrical performance.

  9. Systematic tests for position-dependent additive shear bias

    NASA Astrophysics Data System (ADS)

    van Uitert, Edo; Schneider, Peter

    2016-11-01

    We present new tests to identify stationary position-dependent additive shear biases in weak gravitational lensing data sets. These tests are important diagnostics for currently ongoing and planned cosmic shear surveys, as such biases induce coherent shear patterns that can mimic and potentially bias the cosmic shear signal. The central idea of these tests is to determine the average ellipticity of all galaxies with shape measurements in a grid in the pixel plane. The distribution of the absolute values of these averaged ellipticities can be compared to randomised catalogues; a difference points to systematics in the data. In addition, we introduce a method to quantify the spatial correlation of the additive bias, which suppresses the contribution from cosmic shear and therefore eases the identification of a position-dependent additive shear bias in the data. We apply these tests to the publicly available shear catalogues from the Canada-France-Hawaii Telescope Lensing Survey (CFHTLenS) and the Kilo Degree Survey (KiDS) and find evidence for a small but non-negligible residual additive bias at small scales. As this residual bias is smaller than the error on the shear correlation signal at those scales, it is highly unlikely that it causes a significant bias in the published cosmic shear results of CFHTLenS. In CFHTLenS, the amplitude of this systematic signal is consistent with zero in fields where the number of stars used to model the point spread function (PSF) is higher than average, suggesting that the position-dependent additive shear bias originates from undersampled PSF variations across the image.

  10. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  11. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  12. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  13. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  14. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  15. Production Hydraulic Packer Field Test

    SciTech Connect

    Schneller, Tricia; Salas, Jose

    2000-06-30

    In October 1999, the Rocky Mountain Oilfield Testing Center and Halliburton Energy Services cooperated on a field test of Halliburton's new Production Hydraulic Packer technology on Well 46-TPX-10 at Naval Petroleum Reserve No. 3 near Casper, WY. Performance of the packer was evaluated in set and unset operations. The packer's ability to seal the annulus between the casing and tubing was hydraulically tested and the results were recorded.

  16. The North Carolina Field Test

    SciTech Connect

    Sharp, T.R.; Ternes, M.P.

    1990-08-01

    The North Carolina Field Test will test the effectiveness of two weatherization approaches: the current North Carolina Low-Income Weatherization Assistance Program and the North Carolina Field Test Audit. The Field Test Audit will differ from North Carolina's current weatherization program in that it will incorporate new weatherization measures and techniques, a procedure for basing measure selection of the characteristics of the individual house and the cost-effectiveness of the measure, and also emphasize cooling energy savings. The field test will determine the differences of the two weatherization approaches from the viewpoints of energy savings, cost effectiveness, and implementation ease. This Experimental Plan details the steps in performing the field test. The field test will be a group effort by several participating organizations. Pre- and post-weatherization data will be collected over a two-year period (November 1989 through August 1991). The 120 houses included in the test will be divided into a control group and two treatment groups (one for each weatherization procedure) of 40 houses each. Weekly energy use data will be collected for each house representing whole-house electric, space heating and cooling, and water heating energy uses. Corresponding outdoor weather and house indoor temperature data will also be collected. The energy savings of each house will be determined using linear-regression based models. To account for variations between the pre- and post-weatherization periods, house energy savings will be normalized for differences in outdoor weather conditions and indoor temperatures. Differences between the average energy savings of treatment groups will be identified using an analysis of variance approach. Differences between energy savings will be quantified using multiple comparison techniques. 9 refs., 8 figs., 5 tabs.

  17. Descent Advisor Preliminary Field Test

    NASA Technical Reports Server (NTRS)

    Green, Steven M.; Vivona, Robert A.; Sanford, Beverly

    1995-01-01

    A field test of the Descent Advisor (DA) automation tool was conducted at the Denver Air Route Traffic Control Center in September 1994. DA is being developed to assist Center controllers in the efficient management and control of arrival traffic. DA generates advisories, based on trajectory predictions, to achieve accurate meter-fix arrival times in a fuel efficient manner while assisting the controller with the prediction and resolution of potential conflicts. The test objectives were: (1) to evaluate the accuracy of DA trajectory predictions for conventional and flight-management system equipped jet transports, (2) to identify significant sources of trajectory prediction error, and (3) to investigate procedural and training issues (both air and ground) associated with DA operations. Various commercial aircraft (97 flights total) and a Boeing 737-100 research aircraft participated in the test. Preliminary results from the primary test set of 24 commercial flights indicate a mean DA arrival time prediction error of 2.4 seconds late with a standard deviation of 13.1 seconds. This paper describes the field test and presents preliminary results for the commercial flights.

  18. Cryopumping Field Joint Can Testing

    NASA Technical Reports Server (NTRS)

    Johnson, Wesley L.; Fesmire, James E.; Meneghelli, Barry E.

    2011-01-01

    For long installations, vacuum jacketed piping often comes in 40 foot sections that are butt welded together in the field. A short can is then welded over the bare pipe connection to allow for insulation to be protected from the environment. Traditionally, the field joint is insulated with multilayer insulation and a vacuum is pulled on the can to minimize heat leak through the bare section and prevent frost from forming on the pipe section. The vacuum jacketed lines for the Ares I mobile launch platform were to be a combined 2000 feet long, with 60+ pipe sections and field joint cans. Historically, Kennedy Space Center has drilled a hole in the long sections to create a common vacuum with the field joint can to minimize maintenance on the vacuum jacketed piping. However, this effort looked at ways to use a passive system that didn't require a vacuum, but may cryopump to create its own vacuum. Various forms of aerogel, multilayer insulations, and combinations thereof were tested to determine the best method of insulating the field joint while minimizing maintenance and thermal losses.

  19. Full-engine field test

    SciTech Connect

    Gianola, M.

    1988-10-01

    For purposes of both final verification and optimization of TG 20 and TG 50 combustion systems, test programs have been carried out directly on full engines operating in the field, as well as in the test bench. These programs were carried out in two separate phases: the first one directed to determine the behavior at load by means of experimental data acquisition, including temperature distribution on the combustor exit plane for different burner arrangements, and the second one directed to optimize the ignition process and the acceleration sequence. This paper, after a brief description of the instrumentation used for each test, reports the most significant results burning both fuel oil and natural gas. Moreover, some peculiar operational problems are mentioned, along with their diagnosis and the corrections applied to the combustion system to solve them.

  20. The four-meter confrontation visual field test.

    PubMed

    Kodsi, S R; Younge, B R

    1992-01-01

    The 4-m confrontation visual field test has been successfully used at the Mayo Clinic for many years in addition to the standard 0.5-m confrontation visual field test. The 4-m confrontation visual field test is a test of macular function and can identify small central or paracentral scotomas that the examiner may not find when the patient is tested only at 0.5 m. Also, macular sparing in homonymous hemianopias and quadrantanopias may be identified with the 4-m confrontation visual field test. We recommend use of this confrontation visual field test, in addition to the standard 0.5-m confrontation visual field test, on appropriately selected patients to obtain the most information possible by confrontation visual field tests.

  1. Digital Audio Radio Field Tests

    NASA Technical Reports Server (NTRS)

    Hollansworth, James E.

    1997-01-01

    Radio history continues to be made at the NASA Lewis Research Center with the beginning of phase two of Digital Audio Radio testing conducted by the Consumer Electronic Manufacturers Association (a sector of the Electronic Industries Association and the National Radio Systems Committee) and cosponsored by the Electronic Industries Association and the National Association of Broadcasters. The bulk of the field testing of the four systems should be complete by the end of October 1996, with results available soon thereafter. Lewis hosted phase one of the testing process, which included laboratory testing of seven proposed digital audio radio systems and modes (see the following table). Two of the proposed systems operate in two modes, thus making a total of nine systems for testing. These nine systems are divided into the following types of transmission: in-band on channel (IBOC), in-band adjacent channel (IBAC), and new bands - the L-band (1452 to 1492 MHz) and the S-band (2310 to 2360 MHz).

  2. Test Procedure - pumping system for caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1994-10-01

    This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

  3. 30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING WEST. ORIGINALLY HAD SUSPENDED ACOUSTICAL CEILINGS WITH FLOURESCENT LIGHTING AND ASPHALT MASTIC TILE FLOORS - Underwriters' Laboratories, 207-231 East Ohio Street, Chicago, Cook County, IL

  4. Additive CHARMM force field for naturally occurring modified ribonucleotides.

    PubMed

    Xu, You; Vanommeslaeghe, Kenno; Aleksandrov, Alexey; MacKerell, Alexander D; Nilsson, Lennart

    2016-04-15

    More than 100 naturally occurring modified nucleotides have been found in RNA molecules, in particular in tRNAs. We have determined molecular mechanics force field parameters compatible with the CHARMM36 all-atom additive force field for all these modifications using the CHARMM force field parametrization strategy. Emphasis was placed on fine tuning of the partial atomic charges and torsion angle parameters. Quantum mechanics calculations on model compounds provided the initial set of target data, and extensive molecular dynamics simulations of nucleotides and oligonucleotides in aqueous solutions were used for further refinement against experimental data. The presented parameters will allow for computational studies of a wide range of RNAs containing modified nucleotides, including the ribosome and transfer RNAs.

  5. Additive CHARMM force field for naturally occurring modified ribonucleotides

    PubMed Central

    Xu, You; Vanommeslaeghe, Kenno; Aleksandrov, Alexey; MacKerell, Alexander D.

    2016-01-01

    More than 100 naturally occurring modified nucleotides have been found in RNA molecules, in particular in tRNAs. We have determined molecular mechanics force field parameters compatible with the CHARMM36 all‐atom additive force field for all these modifications using the CHARMM force field parametrization strategy. Emphasis was placed on fine tuning of the partial atomic charges and torsion angle parameters. Quantum mechanics calculations on model compounds provided the initial set of target data, and extensive molecular dynamics simulations of nucleotides and oligonucleotides in aqueous solutions were used for further refinement against experimental data. The presented parameters will allow for computational studies of a wide range of RNAs containing modified nucleotides, including the ribosome and transfer RNAs. © 2016 The Authors. Journal of Computational Chemistry Published by Wiley Periodicals, Inc. PMID:26841080

  6. Additional electric field in real trench MOS barrier Schottky diode

    NASA Astrophysics Data System (ADS)

    Mamedov, R. K.; Aslanova, A. R.

    2016-04-01

    In real trench MOS barrier Schottky diode (TMBS diode) additional electric field (AEF) the whole is formed in the near contact region of the semiconductor and its propagation space is limited with the barrier metal and the metallic electrodes of MOS structures. Effective potential barrier height TMBS diode is formed via resulting electric field of superposition AEF and electric field of space charge region (SCR) semiconductor. The dependence of the resulting electric field intensity of the distance towards the inside the semiconductor is nonlinear and characterized by a peak at a certain distance from the interface. The thickness of the SCR in TMBS diode becomes equal to the trench depth. Force and energy parameters of the AEF, and thus resulting electric field in the SCR region, become dependent on the geometric design parameters TMBS diode. The forward I-V characteristic TMBS diode is described by the thermionic emission theory as in conventional flat Scottky diode, and in the reverse bias, current is virtually absent at initial voltage, appears abruptly at a certain critical voltage.

  7. Tests of compensatory vs. additive hypotheses of mortality in mallards

    USGS Publications Warehouse

    Burnham, Kenneth P.; Anderson, David R.

    1984-01-01

    Band recovery data from over 410 000 adult Mallards (Anas platyrhynchos) banded in North America between 1950 and 1979 were analyzed to examine the effect of exploitation on annual survival rate. Two extreme hypotheses were defined: completely compensatory, and totally additive, and an explicit mathematical model was presented to represent each hypothesis. Comparison of the values of the log-likelihood functions at their maxima allowed discrimination between the two models (hypotheses). Extensive Monte Carlo studies were made on the performance of the discriminant test and the power of the test under the two extreme hypotheses and a range of intermediate hypotheses. The results of the discriminant tests on the data agreed closely with the expected performance of the test if the true underlying process was compensatory. We rejected the hypothesis of total additivity (P=.001). Instead, it appears that hunting mortalities are largely compensated for by other forms of mortality.

  8. Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

    PubMed

    Law, S L; Newman, J H; Ptak, F L

    1990-02-01

    A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

  9. Basophil activation test with food additives in chronic urticaria patients.

    PubMed

    Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up; Chang, Yoon-Seok

    2014-01-01

    The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU.

  10. Testing energy non-additivity in white dwarfs

    NASA Astrophysics Data System (ADS)

    Carmona, J. M.; Cortés, J. L.; Gracia-Ruiz, R.; Loret, N.

    2014-03-01

    We consider a particular effect which can be expected in scenarios of deviations from special relativity induced by Planckian physics: the loss of additivity in the total energy of a system of particles. We argue about the necessity to introduce a length scale to control the effects of non-additivity for macroscopic objects and consider white dwarfs as an appropriate laboratory to test this kind of new physics. We study the sensitivity of the mass-radius relation of the Chandrasekhar model to these corrections by comparing the output of a simple phenomenological model to observational data of white dwarfs.

  11. IN SITU FIELD TESTING OF PROCESSES

    SciTech Connect

    J.S.Y. YANG

    2004-11-08

    The purpose of this scientific analysis report is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts and surface-based boreholes through unsaturated zone (UZ) tuff rock units. In situ testing, monitoring, and associated laboratory studies are conducted to directly assess and evaluate the waste emplacement environment and the natural barriers to radionuclide transport at Yucca Mountain. This scientific analysis report supports and provides data to UZ flow and transport model reports, which in turn contribute to the Total System Performance Assessment (TSPA) of Yucca Mountain, an important document for the license application (LA). The objectives of ambient field-testing activities are described in Section 1.1. This report is the third revision (REV 03), which supercedes REV 02. The scientific analysis of data for inputs to model calibration and validation as documented in REV 02 were developed in accordance with the Technical Work Plan (TWP) ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (BSC 2004 [DIRS 167969]). This revision was developed in accordance with the ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654], Section 1.2.4) for better integrated, consistent, transparent, traceable, and more complete documentation in this scientific analysis report and associated UZ flow and transport model reports. No additional testing or analyses were performed as part of this revision. The list of relevant acceptance criteria is provided by ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654]), Table 3-1. Additional deviations from the TWP regarding the features, events, and processes (FEPs) list are discussed in Section 1.3. Documentation in this report includes descriptions of how, and under what conditions, the tests were conducted. The descriptions and

  12. Introduction to Analog Field Testing

    NASA Video Gallery

    NASA tests systems and operational concepts in analog environments, which include locations underwater, in the arctic, on terrestrial impact craters, in the desert, and on the International Space S...

  13. Statistical tests of additional plate boundaries from plate motion inversions

    NASA Technical Reports Server (NTRS)

    Stein, S.; Gordon, R. G.

    1984-01-01

    The application of the F-ratio test, a standard statistical technique, to the results of relative plate motion inversions has been investigated. The method tests whether the improvement in fit of the model to the data resulting from the addition of another plate to the model is greater than that expected purely by chance. This approach appears to be useful in determining whether additional plate boundaries are justified. Previous results have been confirmed favoring separate North American and South American plates with a boundary located beween 30 N and the equator. Using Chase's global relative motion data, it is shown that in addition to separate West African and Somalian plates, separate West Indian and Australian plates, with a best-fitting boundary between 70 E and 90 E, can be resolved. These results are generally consistent with the observation that the Indian plate's internal deformation extends somewhat westward of the Ninetyeast Ridge. The relative motion pole is similar to Minster and Jordan's and predicts the NW-SE compression observed in earthquake mechanisms near the Ninetyeast Ridge.

  14. Analyzing Educational Testing Service Graduate Major Field Test Results

    ERIC Educational Resources Information Center

    Thornton, Barry; Arbogast, Gordon

    2012-01-01

    The Educational Testing Service (ETS) created the Graduate Major Field Test in Business (GMFT-B) for MBA students. This test is administered to all MBA classes at Jacksonville University for the purpose of measuring student academic achievement and growth, as well as to assess educational outcomes. The test is given in the capstone course,…

  15. Laboratory and Field Evaluation of Fluid-Loss Additive Systems Used in the Williston Basin

    SciTech Connect

    Woo, G.T.; Cramer, D.D.

    1984-05-01

    Many formations in the Williston Basin are naturally fractured limestones and dolomites. Naturally fractured reservoirs are typically the most difficult to maintain control of fracturing fluid leakoff. Treatments in the Mission Canyon, Midale and Ratcliffe formations of the Madison Group have had high fracturing fluid leakoffs. Polymer/inert solids mixtures, 100 mesh sand, silica flour and oil-soluble resins have been used in an attempt to control fluid loss. These additives have not consistently solved the problem of excessive fluid loss, and frequent screenouts, gel-outs or pressure-outs have resulted. A laboratory simulation of naturally fractured reservoir leakoff was employed to evaluate the efficiency of ten fluid loss additive systems. Tapered-slot fluid loss tests and proppant pack damage tests were performed using each additive system. Five fluid loss additive systems were identified which performed well in both tests. This paper also summarizes the results of a field evaluation of nine of the original ten fluid loss additive systems used in 70 wells in the Madison Group. Two fluid loss additive systems, a mixture of silica flour and 100 mesh sand, and a mixture of oil-soluble resin (nominal 250 mesh) and 100 mesh sand, performed well in the laboratory tests and had a high success rate in the field.

  16. Development of additional tasks for the executive function performance test.

    PubMed

    Hahn, Bridget; Baum, Carolyn; Moore, Jennifer; Ehrlich-Jones, Linda; Spoeri, Susan; Doherty, Meghan; Wolf, Timothy J

    2014-01-01

    OBJECTIVE. The Executive Function Performance Test (EFPT) is a reliable and valid performance-based assessment of executive function for people with stroke. The objective of this study was to enhance the clinical utility of the EFPT by developing and testing additional tasks for the EFPT in the Alternate EFPT (aEFPT). METHOD. We performed a cross-sectional study with poststroke participants (n = 25) and healthy control participants (n = 25). All participants completed a neuropsychological assessment battery and both the EFPT and the aEFPT. RESULTS. No statistically significant differences were found between the EFPT and the aEFPT when examining total scores, construct scores, and two overall task scores. Correlations between the aEFPT and the neuropsychological measures were adequate to strong (r2s = .59-.83). CONCLUSION. The aEFPT tasks are comparable to the original EFPT tasks, providing occupational therapy practitioners with additional tasks that can be used clinically to identify performance-based executive function deficits in people with stroke.

  17. Test fields cannot destroy extremal black holes

    NASA Astrophysics Data System (ADS)

    Natário, José; Queimada, Leonel; Vicente, Rodrigo

    2016-09-01

    We prove that (possibly charged) test fields satisfying the null energy condition at the event horizon cannot overspin/overcharge extremal Kerr-Newman or Kerr-Newman-anti de Sitter black holes, that is, the weak cosmic censorship conjecture cannot be violated in the test field approximation. The argument relies on black hole thermodynamics (without assuming cosmic censorship), and does not depend on the precise nature of the fields. We also discuss generalizations of this result to other extremal black holes.

  18. Diamond field emitter array cathodes and possibilities of employing additive manufacturing for dielectric laser accelerating structures

    NASA Astrophysics Data System (ADS)

    Simakov, Evgenya I.; Andrews, Heather L.; Herman, Matthew J.; Hubbard, Kevin M.; Weis, Eric

    2017-03-01

    Demonstration of a stand-alone practical dielectric laser accelerator (DLA) requires innovation in two major critical components: high-current ultra-low-emittance cathodes and efficient laser accelerator structures. LANL develops two technologies that in our opinion are applicable to the novel DLA architectures: diamond field emitter array (DFEA) cathodes and additive manufacturing of photonic band-gap (PBG) structures. This paper discusses the results of testing of DFEA cathodes in the field-emission regime and the possibilities for their operation in the photoemission regime, and compares their emission characteristics to the specific needs of DLAs. We also describe recent advances in additive manufacturing of dielectric woodpile structures using a Nanoscribe direct laser-writing device capable of maskless lithography and additive manufacturing, and the development of novel infrared dielectric materials compatible with additive manufacturing.

  19. AFCATT (Anti-Fouling Chemical Additive Test Tower)

    SciTech Connect

    Philpot, E.F.; Newton, M.T.; Noble, R.T.

    1995-06-01

    Polyvinylchloride (PVC) film-type cellular fill is the fill of choice in replacing cement asbestos board fill in existing cooling towers and in new cooling towers because of its high thermal performance, ease of installation, and low initial cost. However, PVC fill has been found to foul quickly with biological and sediment material, significantly reducing tower performance and the fill`s useful life. The Anti-Fouling Chemical Additives Test Tower (AFCATT) has been build to study accumulation rates of fouling deposits in corrugated PVC film fill and to study methods of cleaning and preventing the fouling deposits. This small mechanical draft cooling tower is located next to the Unit 4 natural draft cooling tower at Georgia Power Company`s Plant Bowen. The once-through mechanical draft tower receives hot water from the condenser and returns the cold water to the basin of the host tower. The pilot tower is divided into four chambers allowing for three different treatment programs and one control to be run simultaneously. PVC fill packs are suspended from load cells to allow the weight of the fill packs to be measured continuously. Six vendors participated in the summer 1993 test program. Each proposed different methods of cleaning the fouled fill and were given the opportunity to try their proposed method of fill cleaning. To determine the success of these different treatment programs, statistical analyses were performed on the collected data and the changes in the accumulation rates compared.

  20. Additives

    NASA Technical Reports Server (NTRS)

    Smalheer, C. V.

    1973-01-01

    The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

  1. Hydrogen Field Test Standard: Laboratory and Field Performance

    PubMed Central

    Pope, Jodie G.; Wright, John D.

    2015-01-01

    The National Institute of Standards and Technology (NIST) developed a prototype field test standard (FTS) that incorporates three test methods that could be used by state weights and measures inspectors to periodically verify the accuracy of retail hydrogen dispensers, much as gasoline dispensers are tested today. The three field test methods are: 1) gravimetric, 2) Pressure, Volume, Temperature (PVT), and 3) master meter. The FTS was tested in NIST's Transient Flow Facility with helium gas and in the field at a hydrogen dispenser location. All three methods agree within 0.57 % and 1.53 % for all test drafts of helium gas in the laboratory setting and of hydrogen gas in the field, respectively. The time required to perform six test drafts is similar for all three methods, ranging from 6 h for the gravimetric and master meter methods to 8 h for the PVT method. The laboratory tests show that 1) it is critical to wait for thermal equilibrium to achieve density measurements in the FTS that meet the desired uncertainty requirements for the PVT and master meter methods; in general, we found a wait time of 20 minutes introduces errors < 0.1 % and < 0.04 % in the PVT and master meter methods, respectively and 2) buoyancy corrections are important for the lowest uncertainty gravimetric measurements. The field tests show that sensor drift can become a largest component of uncertainty that is not present in the laboratory setting. The scale was calibrated after it was set up at the field location. Checks of the calibration throughout testing showed drift of 0.031 %. Calibration of the master meter and the pressure sensors prior to travel to the field location and upon return showed significant drifts in their calibrations; 0.14 % and up to 1.7 %, respectively. This highlights the need for better sensor selection and/or more robust sensor testing prior to putting into field service. All three test methods are capable of being successfully performed in the field and give

  2. Livestock poisoning from oil field drilling fluids, muds and additives.

    PubMed

    Edwards, W C; Gregory, D G

    1991-10-01

    The use and potential toxicity of various components of oil well drilling fluids, muds and additives are presented. Many components are extremely caustic resulting in rumenitis. Solvent and petroleum hydrocarbon components may cause aspiration pneumonia and rumen dysfunction. Some additives cause methemoglobinemia. The most frequently encountered heavy metals are lead, chromium, arsenic, lithium and copper. Considerations for investigating livestock poisoning cases and several typical cases are reviewed.

  3. Livestock poisoning from oil field drilling fluids, muds and additives

    SciTech Connect

    Edwards, W.C.; Gregory, D.G. )

    1991-10-01

    The use and potential toxicity of various components of oil well drilling fluids, muds and additives are presented. Many components are extremely caustic resulting in rumenitis. Solvent and petroleum hydrocarbon components may cause aspiration pneumonia and rumen dysfunction. Some additives cause methemoglobinemia. The most frequently encountered heavy metals are lead, chromium, arsenic, lithium and copper. Considerations for investigating livestock poisoning cases and several typical cases are reviewed.

  4. Testing for Additivity at Select Mixture Groups of Interest Based on Statistical Equivalence Testing Methods

    SciTech Connect

    Stork, LeAnna M.; Gennings, Chris; Carchman, Richard; Carter, Jr., Walter H.; Pounds, Joel G.; Mumtaz, Moiz

    2006-12-01

    Several assumptions, defined and undefined, are used in the toxicity assessment of chemical mixtures. In scientific practice mixture components in the low-dose region, particularly subthreshold doses, are often assumed to behave additively (i.e., zero interaction) based on heuristic arguments. This assumption has important implications in the practice of risk assessment, but has not been experimentally tested. We have developed methodology to test for additivity in the sense of Berenbaum (Advances in Cancer Research, 1981), based on the statistical equivalence testing literature where the null hypothesis of interaction is rejected for the alternative hypothesis of additivity when data support the claim. The implication of this approach is that conclusions of additivity are made with a false positive rate controlled by the experimenter. The claim of additivity is based on prespecified additivity margins, which are chosen using expert biological judgment such that small deviations from additivity, which are not considered to be biologically important, are not statistically significant. This approach is in contrast to the usual hypothesis-testing framework that assumes additivity in the null hypothesis and rejects when there is significant evidence of interaction. In this scenario, failure to reject may be due to lack of statistical power making the claim of additivity problematic. The proposed method is illustrated in a mixture of five organophosphorus pesticides that were experimentally evaluated alone and at relevant mixing ratios. Motor activity was assessed in adult male rats following acute exposure. Four low-dose mixture groups were evaluated. Evidence of additivity is found in three of the four low-dose mixture groups.The proposed method tests for additivity of the whole mixture and does not take into account subset interactions (e.g., synergistic, antagonistic) that may have occurred and cancelled each other out.

  5. Gasoline and Diesel Fuel Test Methods Additional Resources

    EPA Pesticide Factsheets

    Supporting documents on the Direct Final Rule that allows refiners and laboratories to use more current and improved fuel testing procedures for twelve American Society for Testing and Materials analytical test methods.

  6. Field Test of the Verbal Skills Curriculum.

    DTIC Science & Technology

    1982-08-01

    twon.) A Verbal Skills Curriculum program, designed for recruits with deficiencies in English language listening and speaking , was field-tested at... Skills program and presents the results of a field test of the program with recruits who speak English as a second language. The reoort also presents... Skills Curriculum provides remedial instruction to recruits experiencing difficulty in English language speaking or listening skills . English language

  7. Adipic gets the acid test as flue gas scrubber additive

    SciTech Connect

    Miller, I.R.

    1980-02-11

    The first full-scale demonstration of adipic acid for such use, to be conducted early in the summer of 1980 in a 200 MW power plant burning high-sulfur coal, is designed to clarify the costs and show how to reduce losses of adipic acid via degradation. Adipic acid improves SO/sub 2/ removal by acting as a buffer to limit the pH drop normally occurring at the gas-liquid interface so that the higher SO/sub 2/ concentration in the surface film improves liquid-phase mass transfer; it also promotes higher limestone utilization. Prepared by the Tennessee Valley Authority, a preliminary economic analysis for a 500 MW plant burning 4% sulfur coal indicates that the addition of 1500 ppM of adipic acid (limestone at $7/ton and the acid at $840/ton) would raise SO/sub 2/ removal from 90 to 95%, reduce the total capital investment from $41.5 to $39.5 million, and have a first year revenue requirement of $19.9 million vs. $20.9 million without the acid. The large-scale trial will also help clarify concern over unpleasant odors that have been reported at test sites of the limestone/adipic system; valeric acid has been identified as the cause.

  8. Testing Large Structures in the Field

    NASA Technical Reports Server (NTRS)

    James, George; Carne, Thomas G.

    2009-01-01

    Field testing large structures creates unique challenges such as limited choices for boundary conditions and the fact that natural excitation sources cannot be removed. Several critical developments in field testing of large structures are reviewed, including: step relaxation testing which has been developed into a useful technique to apply large forces to operational systems by careful windowing; the capability of large structures testing with free support conditions which has been expanded by implementing modeling of the support structure; natural excitation which has been developed as a viable approach to field testing; and the hybrid approach which has been developed to allow forces to be estimated in operating structures. These developments have increased the ability to extract information from large structures and are highlighted in this presentation.

  9. Additional Revised Push-Up Test Norms for College Students

    ERIC Educational Resources Information Center

    Mozumdar, Arupendra; Liguori, Gary; Baumgartner, Ted A.

    2010-01-01

    The push-up test is commonly used to assess arm and shoulder girdle strength and endurance. Baumgartner, Oh, Chung, and Hales (2002) developed a revised push-up test for college students with a standardized test protocol. The purpose of the present study was to develop percentile norms for the revised push-up test based on the push-up scores of…

  10. Field evaluation of some bait additives against Indian crested porcupine (Hystrix indica) (Rodentia: Hystricidae).

    PubMed

    Mushtaq, Muhammad; Hussain, Iftikhar; Mian, Afsar; Munir, Shahid; Ahmed, Irfan; Khan, Abdul Aziz

    2013-09-01

    This research study evaluated the effect of different additives on the bait consumption by Indian crested porcupine, a serious forest and agricultural pest, under field conditions. Different additives (saccharin, common salt, bone meal, fish meal, peanut butter, egg yolk, egg shell powder, yeast powder, mineral oil and coconut oil) at 2 and 5% each were tested for their relative preference, using groundnut-maize (1:1) as basic bait. All the additives were tested under a no-choice test pattern. For control tests, no additive was mixed with the basic bait. Saccharin at 5% concentration significantly enhanced the consumption of bait over the basic bait, while 2% saccharin supplemented bait resulted in a non-significant bait consumption. All other additives did not enhance the consumption of the bait material; rather, these worked as repellents. However, the repellency was lowest with the common salt, followed by egg yolk, egg shell powder, bone meal, peanut butter, mineral oil, fish meal and yeast powder, while coconut remained the most repellent compound. The present study suggested that groundnut-maize (1:1) supplemented with 5% saccharin was the preferred bait combination, and can be used with different rodenticides for the management of Indian crested porcupine.

  11. SRS environmental technology development field test platform

    SciTech Connect

    Riha, B.D.; Rossabi, J.; Eddy-Dilek, C.A.

    1995-09-01

    A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper provides an overview of the field test site and a description of some of the technologies demonstrated at the site including their field applications.

  12. Trip Report-Produced-Water Field Testing

    SciTech Connect

    Sullivan, Enid J.

    2012-05-25

    Los Alamos National Laboratory (LANL) conducted field testing of a produced-water pretreatment apparatus with assistance from faculty at the Texas A&M University (TAMU) protein separation sciences laboratory located on the TAMU main campus. The following report details all of the logistics surrounding the testing. The purpose of the test was to use a new, commercially-available filter media housing containing modified zeolite (surfactant-modified zeolite or SMZ) porous medium for use in pretreatment of oil and gas produced water (PW) and frac-flowback waters. The SMZ was tested previously in October, 2010 in a lab-constructed configuration ('old multicolumn system'), and performed well for removal of benzene, toluene, ethylbenzene, and xylenes (BTEX) from PW. However, a less-expensive, modular configuration is needed for field use. A modular system will allow the field operator to add or subtract SMZ filters as needed to accommodate site specific conditions, and to swap out used filters easily in a multi-unit system. This test demonstrated the use of a commercial filter housing with a simple flow modification and packed with SMZ for removing BTEX from a PW source in College Station, Texas. The system will be tested in June 2012 at a field site in Pennsylvania for treating frac-flowback waters. The goals of this test are: (1) to determine sorption efficiency of BTEX in the new configuration; and (2) to observe the range of flow rates, backpressures, and total volume treated at a given flow rate.

  13. Field Testing of Environmentally Friendly Drilling System

    SciTech Connect

    David Burnett

    2009-05-31

    The Environmentally Friendly Drilling (EFD) program addresses new low-impact technology that reduces the footprint of drilling activities, integrates light weight drilling rigs with reduced emission engine packages, addresses on-site waste management, optimizes the systems to fit the needs of a specific development sites and provides stewardship of the environment. In addition, the program includes industry, the public, environmental organizations, and elected officials in a collaboration that addresses concerns on development of unconventional natural gas resources in environmentally sensitive areas. The EFD program provides the fundamentals to result in greater access, reasonable regulatory controls, lower development cost and reduction of the environmental footprint associated with operations for unconventional natural gas. Industry Sponsors have supported the program with significant financial and technical support. This final report compendium is organized into segments corresponding directly with the DOE approved scope of work for the term 2005-2009 (10 Sections). Each specific project is defined by (a) its goals, (b) its deliverable, and (c) its future direction. A web site has been established that contains all of these detailed engineering reports produced with their efforts. The goals of the project are to (1) identify critical enabling technologies for a prototype low-impact drilling system, (2) test the prototype systems in field laboratories, and (3) demonstrate the advanced technology to show how these practices would benefit the environment.

  14. Combustion Safety Simplified Test Protocol Field Study

    SciTech Connect

    Brand, L.; Cautley, D.; Bohac, D.; Francisco, P.; Shen, L.; Gloss, S.

    2015-11-01

    Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project team collected field data on 11 houses in 2015.

  15. Background field coils for the High Field Test Facility

    SciTech Connect

    Zbasnik, J.P.; Cornish, D.N.; Scanlan, R.M.; Jewell, A.M.; Leber, R.L.; Rosdahl, A.R.; Chaplin, M.R.

    1980-09-22

    The High Field Test Facility (HFTF), presently under construction at LLNL, is a set of superconducting coils that will be used to test 1-m-o.d. coils of prototype conductors for fusion magnets in fields up to 12 T. The facility consists of two concentric sets of coils; the outer set is a stack of Nb-Ti solenoids, and the inner set is a pair of solenoids made of cryogenically-stabilized, multifilamentary Nb/sub 3/Sn superconductor, developed for use in mirror-fusion magnets. The HFTF system is designed to be parted along the midplane to allow high-field conductors, under development for Tokamak fusion machines, to be inserted and tested. The background field coils were wound pancake-fashion, with cold-welded joints at both the inner and outer diameters. Turn-to-turn insulation was fabricated at LLNL from epoxy-fiberglass strip. The coils were assembled and tested in our 2-m-diam cryostat to verify their operation.

  16. Cold chain: solar refrigerator field tested.

    PubMed

    1983-04-01

    The Health Ministries of Colombia and Peru, in collaboration with the Expanded Program on Immunization (EPI)/Pan American Health Organization (PAHO) and the Centers for Disease Control (CDC), have begun field testing a solar-powered vaccine refrigerator. The aim of the fields trials is to determine whether solar refrigerators can maintain the temperatures required for vaccine storage (+4-8 degrees Celsius) and produce ice at a rate of 2 kg/24 hours under different environmental conditions. these refrigerators would be particularly useful in areas that lack a consistent supply of good quality fuel or where the electrical supply is intermittent or nonexistent. Full appraisal of this technology will require 2 years of field testing; Colombia and Peru expect to complete testing in 1985. To date, 5 models have passed CDC-developed specifications, all of which are manufactured in the US. PAHO/WHO recommends that health ministries should consider the following guidelines in considering the purchase of a particular system: the initial purchase should be for a limited quantity (about 5) of refrigerators to permit field testing; solar panels should meet specific criteria; consideration should be given only to those models that have passed qualification tests; each unit should be fully equipped with monitoring devices and spare parts; and a trained refrigerator technician should be available to repair the equipment.

  17. Numerical simulations of capillary barrier field tests

    SciTech Connect

    Morris, C.E.; Stormont, J.C.

    1997-12-31

    Numerical simulations of two capillary barrier systems tested in the field were conducted to determine if an unsaturated flow model could accurately represent the observed results. The field data was collected from two 7-m long, 1.2-m thick capillary barriers built on a 10% grade that were being tested to investigate their ability to laterally divert water downslope. One system had a homogeneous fine layer, while the fine soil of the second barrier was layered to increase its ability to laterally divert infiltrating moisture. The barriers were subjected first to constant infiltration while minimizing evaporative losses and then were exposed to ambient conditions. The continuous infiltration period of the field tests for the two barrier systems was modelled to determine the ability of an existing code to accurately represent capillary barrier behavior embodied in these two designs. Differences between the field test and the model data were found, but in general the simulations appeared to adequately reproduce the response of the test systems. Accounting for moisture retention hysteresis in the layered system will potentially lead to more accurate modelling results and is likely to be important when developing reasonable predictions of capillary barrier behavior.

  18. Slug tests in wells screened across the water table: some additional considerations.

    PubMed

    Butler, J J

    2014-01-01

    The majority of slug tests done at sites of shallow groundwater contamination are performed in wells screened across the water table and are affected by mechanisms beyond those considered in the standard slug-test models. These additional mechanisms give rise to a number of practical issues that are yet to be fully resolved; four of these are addressed here. The wells in which slug tests are performed were rarely installed for that purpose, so the well design can result in problematic (small signal to noise ratio) test data. The suitability of a particular well design should thus always be assessed prior to field testing. In slug tests of short duration, it can be difficult to identify which portion of the test represents filter-pack drainage and which represents formation response; application of a mass balance can help confirm that test phases have been correctly identified. A key parameter required for all slug test models is the casing radius. However, in this setting, the effective casing radius (borehole radius corrected for filter-pack porosity), not the nominal well radius, is required; this effective radius is best estimated directly from test data. Finally, although conventional slug-test models do not consider filter-pack drainage, these models will yield reasonable hydraulic conductivity estimates when applied to the formation-response phase of a test from an appropriately developed well.

  19. On-line tests of organic additives for the inhibition of the precipitation of silica from hypersaline geothermal brine IV. Final tests of candidate additives

    SciTech Connect

    Harrar, J.E.; Locke, F.E.; Otto, C.H. Jr.; Lorensen, L.E.; Frey, W.P.; Snell, E.O.

    1980-02-01

    The Lawrence Livermore Laboratory Brine Treatment Test System at Niland, Imperial Valley, California, has been used to evaluate a number of cationic polymers and surfactants as scale control agents. An initial group of compounds was narrowed to four on the basis of their activity as silica precipitation inhibitors. Three of these and certain combinations of compounds were then given a 40-h test to determine their effectiveness in retarding scales formed at 220, 125, and 90/sup 0/C. The best single compound was Corcat P-18 (Cordova Chemical Co. polyethylene imine, M.W. approx. = 1800). It had no effect on the scale at 220/sup 0/C, but it reduced the scales at 125 and 90/sup 0/C by factors of 4 and 18, respectively, and it also has activity as a corrosion inhibitor. Other promising compounds are PAE HCl (Dynapol poly(aminoethylene, HCl salt)), which also somewhat reduces the 220/sup 0/C scale; Ethoquad 18/25 (Armak methyl polyoxyethylene(15) octadecylammonium chloride); and Mirapol A-15 (a Miranol Chemical polydiquaternary compound). The best additive formulation for the brines of the Salton Sea Geothermal Field appears to be a mixture of one of these silica precipitation inhibitors with a small amount of hydrochloric acid and a phosphonate crystalline deposit inhibitor. Speculations are presented as to the mechanism of inhibition of silica precipitation and recommendations for further testing of these additives.

  20. Comparative Field Tests of Pressurised Rover Prototypes

    NASA Astrophysics Data System (ADS)

    Mann, G. A.; Wood, N. B.; Clarke, J. D.; Piechochinski, S.; Bamsey, M.; Laing, J. H.

    The conceptual designs, interior layouts and operational performances of three pressurised rover prototypes - Aonia, ARES and Everest - were field tested during a recent simulation at the Mars Desert Research Station in Utah. A human factors experiment, in which the same crew of three executed the same simulated science mission in each of the three vehicles, yielded comparative data on the capacity of each vehicle to safely and comfortably carry explorers away from the main base, enter and exit the vehicle in spacesuits, perform science tasks in the field, and manage geological and biological samples. As well as offering recommendations for design improvements for specific vehicles, the results suggest that a conventional Sports Utility Vehicle (SUV) would not be suitable for analog field work; that a pressurised docking tunnel to the main habitat is essential; that better provisions for spacesuit storage are required; and that a crew consisting of one driver/navigator and two field science crew specialists may be optimal. From a field operations viewpoint, a recurring conflict between rover and habitat crews at the time of return to the habitat was observed. An analysis of these incidents leads to proposed refinements of operational protocols, specific crew training for rover returns and again points to the need for a pressurised docking tunnel. Sound field testing, circulating of results, and building the lessons learned into new vehicles is advocated as a way of producing ever higher fidelity rover analogues.

  1. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Provisions' data analysis, recordkeeping, and reporting requirements in § 63.7(g) refer to the Notification... agreement. (b) Data shall be reduced in accordance with the EPA approved methods specified in the applicable subpart or, if other test methods are used, the data and methods shall be validated according to...

  2. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... provided to the Administrator. (2) When the General Provisions' data analysis, recordkeeping, and reporting... delegated State or local agency) by mutual agreement. (b) Data shall be reduced in accordance with the EPA approved methods specified in the applicable subpart or, if other test methods are used, the data...

  3. Large-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Daniel, Richard C.; Gauglitz, Phillip A.; Burns, Carolyn A.; Fountain, Matthew S.; Shimskey, Rick W.; Billing, Justin M.; Bontha, Jagannadha R.; Kurath, Dean E.; Jenks, Jeromy WJ; MacFarlan, Paul J.; Mahoney, Lenna A.

    2013-08-01

    One of the events postulated in the hazard analysis for the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak event involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids that behave as a Newtonian fluid. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and in processing facilities across the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are mostly absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale testing. The small-scale testing and resultant data are described in Mahoney et al. (2012b), and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used

  4. First Astronaut- Rover Interaction Field Test

    NASA Technical Reports Server (NTRS)

    Kosmo, Joseph J.; Ross, Amy; Cabrol, Nathalie A.

    2000-01-01

    The first Astronaut - Rover (ASRO) Interaction field test was conducted successfully on February 22-27, 1999, in Silver Lake, Mojave Desert, California in a representative planetary surface terrain. This test was a joint effort between the NASA Ames Research Center , Moffett Field, California and the NASA Johnson Space Center, Houston, Texas. As prototype advanced planetary surface space suit and rover technologies are being developed for human planetary surface exploration , it has been determined that it is important to better understand the potential interaction and benefits of an EVA astronaut interacting with a robotic rover . This interaction between an EVA astronaut and a robotic rover is seen as complementary and can greatly enhance the productivity and safety of surface excursions . This test also identified design requirements and options in an advanced space suit and robotic rover. The test objectives were: 1. To identify the operational domains where the EVA astronauts and rover are complementary and can interact and thus collaborate in a safe , productive and cost- effective way, 2. To identify preliminary requirements and recommendations for advanced space suits and rovers that facilitate their cooperative and complementary interaction, 3. To develop operational procedures for the astronaut-rover teams in the identified domains, 4. To test these procedures during representative mission scenarios during field tests by simulating the exploration of a planetary surface by an EVA crew interacting with a robotic rover, 5. To train a space suited test subject, simulated Earth-based and l or lander-based science teams, and robotic vehicle operators in mission configurations, and 6. To evaluate and understand socio-technical aspects of the astronaut - rover interaction experiment in order to guide future technologies and designs. Test results and areas for future research in the design of planetary space suits will be discussed .

  5. Small-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Schonewill, Philip P.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, G. N.; Mahoney, Lenna A.; Tran, Diana N.; Burns, Carolyn A.; Kurath, Dean E.

    2013-08-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are largely absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale. The small-scale testing and resultant data are described in Mahoney et al. (2012b) and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used to mimic the

  6. Development of a Pediatric Visual Field Test

    PubMed Central

    Miranda, Marco A.; Henson, David B.; Fenerty, Cecilia; Biswas, Susmito; Aslam, Tariq

    2016-01-01

    Purpose We describe a pediatric visual field (VF) test based on a computer game where software and hardware combine to provide an enjoyable test experience. Methods The test software consists of a platform-based computer game presented to the central VF. A storyline was created around the game as was a structure surrounding the computer monitor to enhance patients' experience. The patient is asked to help the central character collect magic coins (stimuli). To collect these coins a series of obstacles need to be overcome. The test was presented on a Sony PVM-2541A monitor calibrated from a central midpoint with a Minolta CS-100 photometer placed at 50 cm. Measurements were performed at 15 locations on the screen and the contrast calculated. Retinal sensitivity was determined by modulating stimulus in size. To test the feasibility of the novel approach 20 patients (4–16 years old) with no history of VF defects were recruited. Results For the 14 subjects completing the study, 31 ± 15 data points were collected on 1 eye of each patient. Mean background luminance and stimulus contrast were 9.9 ± 0.3 cd/m2 and 27.9 ± 0.1 dB, respectively. Sensitivity values obtained were similar to an adult population but variability was considerably higher – 8.3 ± 9.0 dB. Conclusions Preliminary data show the feasibility of a game-based VF test for pediatric use. Although the test was well accepted by the target population, test variability remained very high. Translational Relevance Traditional VF tests are not well tolerated by children. This study describes a child-friendly approach to test visual fields in the targeted population. PMID:27980876

  7. Deep Borehole Field Test Conceptual Design Report

    SciTech Connect

    Hardin, Ernest L.

    2016-09-30

    This report documents conceptual design development for the Deep Borehole Field Test (DBFT), including test packages (simulated waste packages, not containing waste) and a system for demonstrating emplacement and retrieval of those packages in the planned Field Test Borehole (FTB). For the DBFT to have demonstration value, it must be based on conceptualization of a deep borehole disposal (DBD) system. This document therefore identifies key options for a DBD system, describes an updated reference DBD concept, and derives a recommended concept for the DBFT demonstration. The objective of the DBFT is to confirm the safety and feasibility of the DBD concept for long-term isolation of radioactive waste. The conceptual design described in this report will demonstrate equipment and operations for safe waste handling and downhole emplacement of test packages, while contributing to an evaluation of the overall safety and practicality of the DBD concept. The DBFT also includes drilling and downhole characterization investigations that are described elsewhere (see Section 1). Importantly, no radioactive waste will be used in the DBFT, nor will the DBFT site be used for disposal of any type of waste. The foremost performance objective for conduct of the DBFT is to demonstrate safe operations in all aspects of the test.

  8. Goldstone field test activities: Target search

    NASA Technical Reports Server (NTRS)

    Tarter, J.

    1986-01-01

    In March of this year prototype SETI equipment was installed at DSS13, the 26 meter research and development antenna at NASA's Goldstone complex of satellite tracking dishes. The SETI equipment will remain at this site at least through the end of the summer so that the hardware and software developed for signal detection and recognition can be fully tested in a dynamic observatory environment. The field tests are expected to help understand which strategies for observing and which signal recognition algorithms perform best in the presence of strong man-made interfering signals (RFI) and natural astronomical sources.

  9. Phase-Field Modeling of Microstructure Evolution in Electron Beam Additive Manufacturing

    NASA Astrophysics Data System (ADS)

    Gong, Xibing; Chou, Kevin

    2015-05-01

    In this study, the microstructure evolution in the powder-bed electron beam additive manufacturing (EBAM) process is studied using phase-field modeling. In essence, EBAM involves a rapid solidification process and the properties of a build partly depend on the solidification behavior as well as the microstructure of the build material. Thus, the prediction of microstructure evolution in EBAM is of importance for its process optimization. Phase-field modeling was applied to study the microstructure evolution and solute concentration of the Ti-6Al-4V alloy in the EBAM process. The effect of undercooling was investigated through the simulations; the greater the undercooling, the faster the dendrite grows. The microstructure simulations show multiple columnar-grain growths, comparable with experimental results for the tested range.

  10. Design, development and field testing of Cecil

    SciTech Connect

    Trovato, S.A. ); Ruggieri, S.K. )

    1990-01-01

    Inspection and cleaning of the secondary side of a pressurized water reactor (PWR) steam generator should be performed on a regular basis to prevent the degradation and early replacement of this equipment due to corrosion. Corrosion products, or sludge, settle in the secondary side of the steam generator and promote corrosion of the tube bundle. The CECIL robot was developed to improve inspection and cleaning of the secondary side of a steam generator. This paper describes the evolution in design of the CECIL robot. The design, development and field testing of the robot at India Point 2 nuclear station are discussed. Particular emphasis is placed on the fourth generation of its design, CECIL-4. The importance of iteration in design, test, fabrication and field application of mobile robots in a nuclear power station is discussed.

  11. Field Test Kit for Gun Residue Detection

    SciTech Connect

    WALKER, PAMELA K.; RODACY, PHILIP J.

    2002-01-01

    One of the major needs of the law enforcement field is a product that quickly, accurately, and inexpensively identifies whether a person has recently fired a gun--even if the suspect has attempted to wash the traces of gunpowder off. The Field Test Kit for Gunshot Residue Identification based on Sandia National Laboratories technology works with a wide variety of handguns and other weaponry using gunpowder. There are several organic chemicals in small arms propellants such as nitrocellulose, nitroglycerine, dinitrotoluene, and nitrites left behind after the firing of a gun that result from the incomplete combustion of the gunpowder. Sandia has developed a colorimetric shooter identification kit for in situ detection of gunshot residue (GSR) from a suspect. The test kit is the first of its kind and is small, inexpensive, and easily transported by individual law enforcement personnel requiring minimal training for effective use. It will provide immediate information identifying gunshot residue.

  12. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E.; Hietala, J.; Wendland, R.D.; Collins, F.

    1992-07-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  13. Ice slurry cooling development and field testing

    SciTech Connect

    Kasza, K.E. ); Hietala, J. ); Wendland, R.D. ); Collins, F. )

    1992-01-01

    A new advanced cooling technology collaborative program is underway involving Argonne National Laboratory (ANL), Northern States Power (NSP) and the Electric Power Research Institute (EPRI). The program will conduct field tests of an ice slurry distributed load network cooling concept at a Northern States Power utility service center to further develop and prove the technology and to facilitate technology transfer to the private sector. The program will further develop at Argonne National Laboratory through laboratory research key components of hardware needed in the field testing and develop an engineering data base needed to support the implementation of the technology. This program will sharply focus and culminate research and development funded by both the US Department of Energy and the Electric Power Research Institute on advanced cooling and load management technology over the last several years.

  14. ADDITIVE TESTING FOR IMPROVED SULFUR RETENTION: PRELIMINARY REPORT

    SciTech Connect

    Amoroso, J.; Fox, K.

    2011-09-07

    The Savannah River National Laboratory is collaborating with Alfred University to evaluate the potential for additives in borosilicate glass to improve sulfur retention. This preliminary report provides further background on the incorporation of sulfur in glass and outlines the experiments that are being performed by the collaborators. A simulated waste glass composition has been selected for the experimental studies. The first phase of experimental work will evaluate the impacts of BaO, PbO, and V{sub 2}O{sub 5} at concentrations of 1.0, 2.0, and 5.0 wt % on sulfate retention in simulated high level waste borosilicate glass. The second phase of experimental work will evaluate the effects of time at the melt temperature on sulfur retention. The resulting samples will be characterized to determine the amount of sulfur remaining as well as to identify the formation of any crystalline phases. The results will be used to guide the future selection of frits and glass forming chemicals in vitrifying Department of Energy wastes containing high sulfur concentrations.

  15. Combustion Safety Simplified Test Protocol Field Study

    SciTech Connect

    Brand, L; Cautley, D.; Bohac, D.; Francisco, P.; Shen, L.; Gloss, S.

    2015-11-05

    "9Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project provides several key results. State weatherization agencies do not generally track combustion safety failures, the data from those that do suggest that there is little actual evidence that combustion safety failures due to spillage from non-dryer exhaust are common and that only a very small number of homes are subject to the failures. The project team collected field data on 11 houses in 2015. Of these homes, two houses that demonstrated prolonged and excessive spillage were also the only two with venting systems out of compliance with the National Fuel Gas Code. The remaining homes experienced spillage that only occasionally extended beyond the first minute of operation. Combustion zone depressurization, outdoor temperature, and operation of individual fans all provide statistically significant predictors of spillage.

  16. A prototype tap test imaging system: Initial field test results

    NASA Astrophysics Data System (ADS)

    Peters, J. J.; Barnard, D. J.; Hudelson, N. A.; Simpson, T. S.; Hsu, D. K.

    2000-05-01

    This paper describes a simple, field-worthy tap test imaging system that gives quantitative information about the size, shape, and severity of defects and damages. The system consists of an accelerometer, electronic circuits for conditioning the signal and measuring the impact duration, a laptop PC and data acquisition and processing software. The images are generated manually by tapping on a grid printed on a plastic sheet laid over the part's surface. A mechanized scanner is currently under development. The prototype has produced images for a variety of aircraft composite and metal honeycomb structures containing flaws, damages, and repairs. Images of the local contact stiffness, deduced from the impact duration using a spring model, revealed quantitatively the stiffness reduction due to flaws and damages, as well as the stiffness enhancement due to substructures. The system has been field tested on commercial and military aircraft as well as rotor blades and engine decks on helicopters. Field test results will be shown and the operation of the system will be demonstrated.—This material is based upon work supported by the Federal Aviation Administration under Contract #DTFA03-98-D-00008, Delivery Order No. IA016 and performed at Iowa State University's Center for NDE as part of the Center for Aviation Systems Reliability program.

  17. Field testing plan for unsaturated zone monitoring and field studies

    SciTech Connect

    Young, M.H.; Wierenga, P.J.; Warrick, A.W.

    1996-10-01

    The University of Arizona, in cooperation with the Bureau of Economic Geology at The University of Texas at Austin, and Stephens and Associates in Albuquerque, New Mexico has developed a field testing plan for evaluating subsurface monitoring systems. The U.S. Nuclear Regulatory Commission has requested development of these testing plans for low-level radioactive waste disposal sites (LLW) and for monitoring at decommissioned facilities designated under the {open_quotes}Site Decommissioning Management Plan{close_quotes} (SDMP). The tests are conducted on a 50 m by 50 m plot on the University of Arizona`s Maricopa Agricultural Center. Within the 50 m by 50 m plot one finds: (1) an instrumented buried trench, (2) monitoring islands similar to those proposed for the Ward Valley, California LLW Facility, (3) deep borehole monitoring sites, (4) gaseous transport monitoring, and (5) locations for testing non-invasive geophysical measurement techniques. The various subplot areas are instrumented with commercially available instruments such as neutron probes, time domain reflectometry probes, tensiometers, psychrometers, heat dissipation sensors, thermocouples, solution samplers, and cross-hole geophysics electrodes. Measurement depths vary from ground surface to 15 m. The data from the controlled flow and transport experiments, conducted over the plot, will be used to develop an integrated approach to long-term monitoring of the vadose zone at waste disposal sites. The data will also be used to test field-scale flow and transport models. This report describes in detail the design of the experiment and the methodology proposed for evaluating the data.

  18. Diamond field emitter array cathodes and possibilities for employing additive manufacturing for dielectric laser accelerating structures

    SciTech Connect

    Simakov, Evgenya Ivanovna; Andrews, Heather Lynn; Herman, Matthew Joseph; Hubbard, Kevin Mark; Weis, Eric

    2016-09-20

    These are slides for a presentation at Stanford University. The outline is as follows: Motivation: customers for compact accelerators, LANL's technologies for laser acceleration, DFEA cathodes, and additive manufacturing of micron-size structures. Among the stated conclusions are the following: preliminary study identified DFEA cathodes as promising sources for DLAs--high beam current and small emittance; additive manufacturing with Nanoscribe Professional GT can produce structures with the right scale features for a DLA operating at micron wavelengths (fabrication tolerances need to be studied, DLAs require new materials). Future plans include DLA experiment with a beam produced by the DFEA cathode with field emission, demonstration of photoemission from DFEAs, and new structures to print and test.

  19. Deep Borehole Field Test Laboratory and Borehole Testing Strategy

    SciTech Connect

    Kuhlman, Kristopher L.; Brady, Patrick V.; MacKinnon, Robert J.; Heath, Jason E.; Herrick, Courtney G.; Jensen, Richard P.; Gardner, W. Payton; Sevougian, S. David; Bryan, Charles R.; Jang, Je-Hun; Stein, Emily R.; Bauer, Stephen J.; Daley, Tom; Freifeld, Barry M.; Birkholzer, Jens; Spane, Frank A.

    2016-09-19

    Deep Borehole Disposal (DBD) of high-level radioactive wastes has been considered an option for geological isolation for many years (Hess et al. 1957). Recent advances in drilling technology have decreased costs and increased reliability for large-diameter (i.e., ≥50 cm [19.7”]) boreholes to depths of several kilometers (Beswick 2008; Beswick et al. 2014). These advances have therefore also increased the feasibility of the DBD concept (Brady et al. 2009; Cornwall 2015), and the current field test design will demonstrate the DBD concept and these advances. The US Department of Energy (DOE) Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste (DOE 2013) specifically recommended developing a research and development plan for DBD. DOE sought input or expression of interest from States, local communities, individuals, private groups, academia, or any other stakeholders willing to host a Deep Borehole Field Test (DBFT). The DBFT includes drilling two boreholes nominally 200m [656’] apart to approximately 5 km [16,400’] total depth, in a region where crystalline basement is expected to begin at less than 2 km depth [6,560’]. The characterization borehole (CB) is the smaller-diameter borehole (i.e., 21.6 cm [8.5”] diameter at total depth), and will be drilled first. The geologic, hydrogeologic, geochemical, geomechanical and thermal testing will take place in the CB. The field test borehole (FTB) is the larger-diameter borehole (i.e., 43.2 cm [17”] diameter at total depth). Surface handling and borehole emplacement of test package will be demonstrated using the FTB to evaluate engineering feasibility and safety of disposal operations (SNL 2016).

  20. 40 CFR 1065.925 - PEMS preparation for field testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false PEMS preparation for field testing... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement Systems § 1065.925 PEMS preparation for field testing. Take the following steps to prepare PEMS for field testing:...

  1. 40 CFR 1065.925 - PEMS preparation for field testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false PEMS preparation for field testing... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement Systems § 1065.925 PEMS preparation for field testing. Take the following steps to prepare PEMS for field testing:...

  2. A new method of field MRTD test

    NASA Astrophysics Data System (ADS)

    Chen, Zhibin; Song, Yan; Liu, Xianhong; Xiao, Wenjian

    2014-09-01

    MRTD is an important indicator to measure the imaging performance of infrared camera. In the traditional laboratory test, blackbody is used as simulated heat source which is not only expensive and bulky but also difficult to meet field testing requirements of online automatic infrared camera MRTD. To solve this problem, this paper introduces a new detection device for MRTD, which uses LED as a simulation heat source and branded plated zinc sulfide glass carved four-bar target as a simulation target. By using high temperature adaptability cassegrain collimation system, the target is simulated to be distance-infinite so that it can be observed by the human eyes to complete the subjective test, or collected to complete objective measurement by image processing. This method will use LED to replace blackbody. The color temperature of LED is calibrated by thermal imager, thereby, the relation curve between the LED temperature controlling current and the blackbody simulation temperature difference is established, accurately achieved the temperature control of the infrared target. Experimental results show that the accuracy of the device in field testing of thermal imager MRTD can be limited within 0.1K, which greatly reduces the cost to meet the project requirements with a wide application value.

  3. Smarter Balanced "Tests of the Test" Successful: Field Test Provides Clear Path Forward

    ERIC Educational Resources Information Center

    Doorey, Nancy

    2014-01-01

    Between March and June of 2014, the Smarter Balanced Assessment Consortium conducted a field test of its new online assessment system. Thirteen participating states provided the results of surveys given to students and adults involved in the Field Test. Overall, more than 70% of test coordinators in each of seven states indicated that the Field…

  4. Testing of Photomultiplier Tubes in a Magnetic Field

    NASA Astrophysics Data System (ADS)

    Waldron, Zachary; A1 Collaboration

    2016-09-01

    The A1 collaboration at MAMI in Mainz, Germany has designed a neutron detector that can be used in experiments to measure the electric form factor of the neutron. They will measure elastic scattering from the neutron, using the polarized electron beam from MAMI at A1's experimental hall. The detector will be composed of two walls of staggered scintillator bars which will be read out by photomultiplier tubes (PMT), connected to both ends of each scintillator via light guides. The experiment requires a magnetic field with strength of 1 Tesla, 2m away from the first scintillator wall. The resulting fringe field is sufficient to disrupt the PMTs, despite the addition of Mu Metal shielding. The effects of the fringe field on these PMTs was tested to optimize the amplification of the PMTs. A Helmholtz Coil was designed to generate a controlled magnetic field with equivalent strength to the field that the PMTs will encounter. The PMTs were read out using a multi-channel analyzer, were tested at various angles relative to the magnetic field in order to determine the optimal orientation to minimize signal disruption. Tests were also performed to determine: the neutron detector response to cosmic radiation; and the best method for measuring a magnetic field's strength in two dimensions. National Science Foundation Grant No. IIA-1358175.

  5. Preliminary Results of Field Emission Cathode Tests

    NASA Technical Reports Server (NTRS)

    Sovey, James S.; Kovaleski, Scott D.

    2001-01-01

    Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

  6. Produced water treating equipment: Recent field tests

    SciTech Connect

    Matthews, R.R.; Choi, M.S.

    1987-01-01

    For several decades, flotation cells have been workhorses for treatment of oilfield produced water for disposal or reinjection. In the last few years several alternative devices which have come on the market for the removal of oil from water have been tested in the oil field. Some of these have distinct advantages over flotation cells in terms of space and weight, better oil-recovery efficiency, and lower operating costs. This paper summarizes the results of field trials of a passive hydrocyclone, in the Arabian Gulf and in the North Sea, a coalescer which uses a specially treated ion-exchange resin as a medium in the Gulf of Mexico, two somewhat similar filter-coalescers which use crushed nut shells as media, onshore in New Mexico, West Texas, and California, and an upflow sand coalescer system in New Mexico and West Texas.

  7. Development of a new field-test procedure for cocaine.

    PubMed

    Tsujikawa, Kenji; Iwata, Yuko T; Segawa, Hiroki; Yamamuro, Tadashi; Kuwayama, Kenji; Kanamori, Tatsuyuki; Inoue, Hiroyuki

    2017-01-01

    The Scott test, widely used as the field test for cocaine, is performed in three steps. If a sample contains cocaine, blue precipitates appear in step 1, the precipitates are dissolved and the solution turns pink in step 2, and the lower layer turns blue in step 3. However, some pyrrolidine-type cathinones produce cocaine-like results when tested, necessitating modification of the test procedure. Filtration of the second-step mixture weakened the blue color in step 3; however, the blue color did not completely disappear. Adding the Chen-Kao reagent to the test procedure enhanced the differentiation: when the reagent was added to cocaine, the solution was initially turbid, but then became clear over time; its addition to cathinones resulted in turquoise or light sky-blue precipitation. These results indicated that the Chen-Kao test was useful for exclusion of cathinones. A combination of the modified Scott test and the Chen-Kao test was successfully applied to the forensic samples containing cocaine or pyrrolidine-type cathinones. In conclusion, a combination of these tests will be the useful field-test procedure for cocaine.

  8. In Situ Field Testing of Processes

    SciTech Connect

    J. Wang

    2001-12-14

    The purpose of this Analysis/Model Report (AMR) is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts of the Yucca Mountain Site Characterization Project (YMP). This revision updates data and analyses presented in the initial issue of this AMR. This AMR was developed in accordance with the ''Technical Work Plan for Unsaturated Zone (UZ) Flow and Transport Process Model Report'' and ''Technical Work Plan for UZ Flow, Transport, and Coupled Processes Process Model Report. These activities were performed to investigate in situ flow and transport processes. The evaluations provide the necessary framework to: (1) refine and confirm the conceptual model of matrix and fracture processes in the unsaturated zone (UZ) and (2) analyze the impact of excavation (including use of construction water and effect of ventilation) on the UZ flow and transport processes. This AMR is intended to support revisions to ''Conceptual and Numerical Models for UZ Flow and Transport'' and ''Unsaturated Zone Flow and Transport Model Process Model Report''. In general, the results discussed in this AMR are from studies conducted using a combination or a subset of the following three approaches: (1) air-injection tests, (2) liquid-release tests, and (3) moisture monitoring using in-drift sensors or in-borehole sensors, to evaluate the impact of excavation, ventilation, and construction-water usage on the surrounding rocks. The liquid-release tests and air-injection tests provide an evaluation of in situ fracture flow and the competing processes of matrix imbibition. Only the findings from testing and data not covered in the ''Seepage Calibration Model and Seepage Testing Data'' are analyzed in detail in the AMR.

  9. CHARMM additive and polarizable force fields for biophysics and computer-aided drug design

    PubMed Central

    Vanommeslaeghe, K.

    2014-01-01

    Background Molecular Mechanics (MM) is the method of choice for computational studies of biomolecular systems owing to its modest computational cost, which makes it possible to routinely perform molecular dynamics (MD) simulations on chemical systems of biophysical and biomedical relevance. Scope of Review As one of the main factors limiting the accuracy of MD results is the empirical force field used, the present paper offers a review of recent developments in the CHARMM additive force field, one of the most popular bimolecular force fields. Additionally, we present a detailed discussion of the CHARMM Drude polarizable force field, anticipating a growth in the importance and utilization of polarizable force fields in the near future. Throughout the discussion emphasis is placed on the force fields’ parametrization philosophy and methodology. Major Conclusions Recent improvements in the CHARMM additive force field are mostly related to newly found weaknesses in the previous generation of additive force fields. Beyond the additive approximation is the newly available CHARMM Drude polarizable force field, which allows for MD simulations of up to 1 microsecond on proteins, DNA, lipids and carbohydrates. General Significance Addressing the limitations ensures the reliability of the new CHARMM36 additive force field for the types of calculations that are presently coming into routine computational reach while the availability of the Drude polarizable force fields offers a model that is an inherently more accurate model of the underlying physical forces driving macromolecular structures and dynamics. PMID:25149274

  10. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Field testing requirements. 236.1035 Section 236... Train Control Systems § 236.1035 Field testing requirements. (a) Before any field testing of an... A through G of this part that the railroad believes are necessary to support the field testing,...

  11. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Field testing requirements. 236.1035 Section 236... Train Control Systems § 236.1035 Field testing requirements. (a) Before any field testing of an... A through G of this part that the railroad believes are necessary to support the field testing,...

  12. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Field testing requirements. 236.1035 Section 236... Train Control Systems § 236.1035 Field testing requirements. (a) Before any field testing of an... A through G of this part that the railroad believes are necessary to support the field testing,...

  13. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Field testing requirements. 236.1035 Section 236... Train Control Systems § 236.1035 Field testing requirements. (a) Before any field testing of an... A through G of this part that the railroad believes are necessary to support the field testing,...

  14. 49 CFR 236.1035 - Field testing requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Field testing requirements. 236.1035 Section 236... Train Control Systems § 236.1035 Field testing requirements. (a) Before any field testing of an... A through G of this part that the railroad believes are necessary to support the field testing,...

  15. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Additional tests for Type A packagings designed...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must...

  16. 3X-100 blade field test.

    SciTech Connect

    Zayas, Jose R.; Johnson, Wesley D.

    2008-03-01

    In support of a Work-For-Other (WFO) agreement between the Wind Energy Technology Department at Sandia National Laboratories and 3TEX, one of the three Micon 65/13M wind turbines at the USDA Agriculture Research Service (ARS) center in Bushland, Texas, has been used to test a set of 9 meter wind turbine blades, manufactured by TPI composites using the 3TEX carbon material for the spar cap. Data collected from the test has been analyzed to evaluate both the aerodynamic performance and the structural response from the blades. The blades aerodynamic and structural performance, the meteorological inflow and the wind turbine structural response has been monitored with an array of 57 instruments: 15 to characterize the blades, 13 to characterize inflow, and 15 to characterize the time-varying state of the turbine. For the test, data was sampled at a rate of 40 Hz using the ATLAS II (Accurate GPS Time-Linked Data Acquisition System) data acquisition system. The system features a time-synchronized continuous data stream and telemetered data from the turbine rotor. This paper documents the instruments and infrastructure that have been developed to monitor these blades, turbines and inflow, as well as both modeling and field testing results.

  17. 76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-31

    ... AGENCY 40 CFR Part 80 RIN 2060-AP17 Regulation of Fuel and Fuel Additives: Alternative Test Method for... correlated to the fuel parameter's respective EPA designated test method. These alternative test methods are... sections 114(a) and 301(a) of the CAA. Regulation of Fuel and Fuel Additives: Alternative Test Method...

  18. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a...) Since some analytes may deteriorate during storage, detected levels of the drug below the...

  19. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a...) Since some analytes may deteriorate during storage, detected levels of the drug below the...

  20. Cooperative field test program for wind systems

    SciTech Connect

    Bollmeier, W.S. II; Dodge, D.M.

    1992-03-01

    The objectives of the Federal Wind Energy Program, managed by the US Department of Energy (DOE), are (1) to assist industry and utilities in achieving a multi-regional US market penetration of wind systems, and (2) to establish the United States as the world leader in the development of advanced wind turbine technology. In 1984, the program conducted a series of planning workshops with representatives from the wind energy industry to obtain input on the Five-Year Research Plan then being prepared by DOE. One specific suggestion that came out of these meetings was that the federal program should conduct cooperative research tests with industry to enhance the technology transfer process. It was also felt that the active involvement of industry in DOE-funded research would improve the state of the art of wind turbine technology. DOE established the Cooperative Field Test Program (CFTP) in response to that suggestion. This program was one of the first in DOE to feature joint industry-government research test teams working toward common objectives.

  1. Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

    NASA Technical Reports Server (NTRS)

    Fikes, John C.

    2014-01-01

    The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

  2. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Special field test authorizations. 73.1515... RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test authorization may be issued to conduct field strength surveys to aid...

  3. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 4 2014-10-01 2014-10-01 false Special field test authorizations. 73.1515... RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test authorization may be issued to conduct field strength surveys to aid...

  4. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 4 2011-10-01 2011-10-01 false Special field test authorizations. 73.1515... RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test authorization may be issued to conduct field strength surveys to aid...

  5. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 4 2013-10-01 2013-10-01 false Special field test authorizations. 73.1515... RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test authorization may be issued to conduct field strength surveys to aid...

  6. Field testing of the Cobra Seal System

    SciTech Connect

    Yellin, E.; Vodrazka, P. ); Ystesund, K.; Drayer, D. )

    1990-01-01

    The Cobra Seal System consists of a passive fiber optic seal and verification equipment which have been modified to take advantage of current technology. The seal permits on-site verification without requiring replacement of the seal. The modifications to the original Cobra Seal System extended the maximum fiber optic cable length from 1 meter to 10 meters. This improvement allowed the Cobra Seal to be considered for application on dry irradiated fuel storage canisters at two Canadian facilities. These canisters are located in an exterior environment exposed to extreme weather conditions. This paper describe the application of the Cobra Seal to these canisters, a housing for the protection of the Cobra Seal body from the environment, and some preliminary results of the IAEA field tests. 4 refs.

  7. Toward a Model for Field-Testing Patient Decision-Support Technologies: A Qualitative Field-Testing Study

    PubMed Central

    Elwyn, Glyn; Edwards, Adrian; Watson, Eila; Austoker, Joan; Grol, Richard

    2007-01-01

    Background Field-testing is a quality assurance criterion in the development of patient decision-support technologies (PDSTs), as identified in the consensus statement of the International Patient Decision Aids Standards Collaboration. We incorporated field-testing into the development of a Web-based, prostate-specific antigen PDST called Prosdex, which was commissioned as part of the UK Prostate Cancer Risk Management Programme. Objectives The aim of this study was to develop a model for the future field-testing of PDSTs, based on the field-testing of Prosdex. Our objectives were (1) to explore the reactions of men to evolving prototypes of Prosdex, (2) to assess the effect of these responses on the development process, and (3) to develop a model for field-testing PDSTs based on the responses and their effect on the development process. Methods Semistructured interviews were conducted with the men after they had viewed evolving prototypes of Prosdex in their homes. The men were grouped according to the prototype viewed. Men between 40 and 75 years of age were recruited from two family practices in different parts of Wales, United Kingdom. In the interviews, the men were asked for their views on Prosdex, both as a whole and in relation to specific sections such as the introduction and video clips. Comments and technical issues that arose during the viewings were noted and fed back to the developers in order to produce subsequent prototypes. Results A total of 27 men were interviewed, in five groups, according to the five prototypes of Prosdex that were developed. The two main themes from the interviews were the responses to the information provided in Prosdex and the responses to specific features of Prosdex. Within these themes, two of the most frequently encountered categories were detail of the information provided and balance between contrasting viewpoints. Criticisms were encountered, particularly with respect to navigation of the site. In addition, we found

  8. Field-enhanced electrodes for additive-injection non-thermal plasma (NTP) processor

    DOEpatents

    Rosocha, Louis A.; Ferreri, Vincent; Kim, Yongho

    2009-04-21

    The present invention comprises a field enhanced electrode package for use in a non-thermal plasma processor. The field enhanced electrode package includes a high voltage electrode and a field-enhancing electrode with a dielectric material layer disposed in-between the high voltage electrode and the field-enhancing electrode. The field-enhancing electrode features at least one raised section that includes at least one injection hole that allows plasma discharge streamers to occur primarily within an injected additive gas.

  9. Calculation of multicenter electric field gradient integrals over Slater-type orbitals using unsymmetrical one-range addition theorems.

    PubMed

    Guseinov, Israfil I; Görgün, Nurşen Seçkin

    2011-06-01

    The electric field induced within a molecule by its electrons determines a whole series of important physical properties of the molecule. In particular, the values of the gradient of this field at the nuclei determine the interaction of their quadrupole moments with the electrons. Using unsymmetrical one-range addition theorems introduced by one of the authors, the sets of series expansion relations for multicenter electric field gradient integrals over Slater-type orbitals in terms of multicenter charge density expansion coefficients and two-center basic integrals are presented. The convergence of the series is tested by calculating concrete cases for different values of quantum numbers, parameters and locations of orbitals.

  10. Test field for airborne laser scanning in Finland

    NASA Astrophysics Data System (ADS)

    Ahokas, E.; Kaartinen, H.; Kukko, A.; Litkey, P.

    2014-11-01

    Airborne laser scanning (ALS) is a widely spread operational measurement tool for obtaining 3D coordinates of the ground surface. There is a need for calibrating the ALS system and a test field for ALS was established at the end of 2013. The test field is situated in the city of Lahti, about 100 km to the north of Helsinki. The size of the area is approximately 3.5 km × 3.2 km. Reference data was collected with a mobile laser scanning (MLS) system assembled on a car roof. Some streets were measured both ways and most of them in one driving direction only. The MLS system of the Finnish Geodetic Institute (FGI) consists of a navigation system (NovAtel SPAN GNSS-IMU) and a laser scanner (FARO Focus3D 120). In addition to the MLS measurements more than 800 reference points were measured using a Trimble R8 VRS-GNSS system. Reference points are along the streets, on parking lots, and white pedestrian crossing line corners which can be used as reference targets. The National Land Survey of Finland has already used this test field this spring for calibrating their Leica ALS-70 scanner. Especially it was easier to determine the encoder scale factor parameter using this test field. Accuracy analysis of the MLS points showed that the point height RMSE is 2.8 cm and standard deviation is 2.6 cm. Our purpose is to measure both more MLS data and more reference points in the test field area to get a better spatial coverage. Calibration flight heights are planned to be 1000 m and 2500 m above ground level. A cross pattern, southwest-northeast and northwest-southeast, will be flown both in opposite directions.

  11. Performance testing of asphalt concrete containing crumb rubber modifier and warm mix additives

    NASA Astrophysics Data System (ADS)

    Ikpugha, Omo John

    Utilisation of scrap tire has been achieved through the production of crumb rubber modified binders and rubberised asphalt concrete. Terminal and field blended asphalt rubbers have been developed through the wet process to incorporate crumb rubber into the asphalt binder. Warm mix asphalt technologies have been developed to curb the problem associated with the processing and production of such crumb rubber modified binders. Also the lowered production and compaction temperatures associated with warm mix additives suggests the possibility of moisture retention in the mix, which can lead to moisture damage. Conventional moisture sensitivity tests have not effectively discriminated good and poor mixes, due to the difficulty of simulating field moisture damage mechanisms. This study was carried out to investigate performance properties of crumb rubber modified asphalt concrete, using commercial warm mix asphalt technology. Commonly utilised asphalt mixtures in North America such as dense graded and stone mastic asphalt were used in this study. Uniaxial Cyclic Compression Testing (UCCT) was used to measure permanent deformation at high temperatures. Indirect Tensile Testing (IDT) was used to investigate low temperature performance. Moisture Induced Sensitivity Testing (MiST) was proposed to be an effective method for detecting the susceptibility of asphalt mixtures to moisture damage, as it incorporates major field stripping mechanisms. Sonnewarm(TM), Sasobit(TM) and Evotherm(TM) additives improved the resistance to permanent deformation of dense graded mixes at a loading rate of 0.5 percent by weight of the binder. Polymer modified mixtures showed superior resistance to permanent deformation compared to asphalt rubber in all mix types. Rediset(TM) WMX improves low temperature properties of dense graded mixes at 0.5 percent loading on the asphalt cement. Rediset LQ and Rediset WMX showed good anti stripping properties at 0.5 percent loading on the asphalt cement. The

  12. In-situ field tests for site characterization and remediation

    SciTech Connect

    Vogel, C.M.

    1995-09-01

    An effort is under way at the Groundwater Remediation Field Laboratory National Test Site at Dover AFB to conduct a field demonstration of bioventing of a controlled release containing a mixture of JP-4 jet fuel and trichloroethylene (TCE). The main objective of the field experiment is to demonstrate that the fuel vapors will support the biological co-oxidation of TCE under the aerobic conditions provided by the bioventing system. Some highly chlorinated compounds, such as perchloroethylene (PCE), cannot be biodegraded under aerobic conditions. However, under the proper anaerobic conditions, PCE can be transformed to harmless degradation products via a series of sequential reductive dechlorination steps. A collaborative effort between the Air Force, Navy and EPA is taking place at Naval Air Station Fallon, Nevada, to determine if complete dechlorination of PCE can be efficiently stimulated in situ by the addition of suitable electron donors. Descriptions of these Air Force research demonstrations and results to date will be discussed in this presentation.

  13. An Efficient Method for Transferring Adult Mosquitoes during Field Tests,

    DTIC Science & Technology

    CULICIDAE, *COLLECTING METHODS, REPRINTS, BLOOD SUCKING INSECTS, FIELD TESTS, HAND HELD, EFFICIENCY, LABORATORY EQUIPMENT, MORTALITY RATES , ADULTS, AEDES, ASPIRATORS, CULICIDAE, TEST AND EVALUATION, REPRINTS

  14. Validity of Field Tests of Upper Body Muscular Strength.

    ERIC Educational Resources Information Center

    Pate, Russell, R; And Others

    1993-01-01

    Examined the validity of field tests of elementary students' upper body muscular strength and endurance. Field tests were found to be moderately valid measures of weight-relative muscular strength but not of absolute strength and muscular endurance. (SM)

  15. A possible field test for marine cloud brightening geoengineering. A possible field test for marine cloud brightening geoengineering

    NASA Astrophysics Data System (ADS)

    Gadian, A.; Wood, R.; Coe, H.; Latham, J.

    2011-12-01

    A possible field test for marine cloud brightening geoengineering. Abstract: The Marine Cloud Brightening (MCB) geoengineering technique (Latham et al 2008) hypothesizes that seeding marine stratocumulus clouds with copious quantities of roughly monodisperse sub-micrometre seawater particles can enhance the cloud droplet number concentration and increase cloud albedo. Here, we propose a set of field tests to critically assess the efficacy of the MCB geoengineering proposal over a limited area. The tests are de minimus with respect to their climate effects. The tests involve three phases, with increasing logistical complexity, each of which is designed to test one or more important components of the cloud brightening scheme. Each involves the introduction and monitoring of controlled aerosol perturbations from one or more ship-based seeding platforms up to a limited area of 100x100 km2. A suite of observational platforms of increasing number and complexity, including aircraft, ships and satellites, will observe the aerosol plume and in the later experiments the cloud and albedo responses to the aerosol perturbations. These responses must include the necessary cloud physical and chemical processes which determine the efficacy of the cloud brightening scheme. Since these processes are also central to the broader problem of aerosol-cloud-climate interactions, such field tests would have significant benefits for climate science in addition to providing a critical test of the MCB hypothesis. Such field experiments should be designed and conducted in an objective manner within the framework of emerging geoengineering research governance structures. Reference: Latham J. et al.. (2008) Global temperature stabilization via controlled albedo enhancement of low-level maritime clouds. Phil. Trans. R. Soc. A doi:10.1098/rsta.2008.0137

  16. Results of the fourth Hanna field test

    SciTech Connect

    Covell, J. R.; Wojdac, L. F.; Barbour, F. A.; Gardner, G. W.; Glass, R.; Hommert, P. J.

    1980-01-01

    The second phase (Hanna IVB) of a coal gasification experiment near Hanna, Wyoming, was completed in September 1979. The experiment attempted to link and gasify coal between process wells spaced 34.3 meters apart. Intermediate wells were positioned between the process wells so that the link could be relayed over shorter distances. Reverse combustion linking was attempted over a 22.9-meter and a 11.4-meter distance of the total well spacing. Thermal activity was generally noted in the upper 3 meters of the coal seam during the link. Two attempts to gasify over the 34.3-meter distance resulted in the propagation of the burn front at the coal overburden interface. Post-burn evaluation indicates fractures as major influencing factors of the combustion process. The Hanna IVB field test provided much insight into influence that geologic features have on in situ coal combustion. The influence of these faults, permeable zones, and cleats, on the air flow patterns can drastically change the overall results of a gasification experiment and should be studied further. The overall results of Hanna IVB were discouraging because of the rapid decline in the heating values for the production gas and the amount of coal gasified. With more complete geologic characerization prior to experimentation and proper well completions, it is believed that most of the subsurface operational problems encountered during Hanna IV could have been avoided.

  17. Addition of Digital Breast Tomosynthesis to Full-Field Digital Mammography in the Diagnostic Setting: Additional Value and Cancer Detectability

    PubMed Central

    Seo, Mirinae; Kim, Sun Ah; Kim, Won Hwa; Lim, Ji He; Lee, Su Hyun; Bae, Min Sun; Koo, Hye Ryoung; Cho, Nariya; Moon, Woo Kyung

    2016-01-01

    Purpose The purpose of this study was to assess the value of adding digital breast tomosynthesis (DBT) to full-field digital mammography (FFDM) in the diagnostic workup of breast cancer and to determine which lesion variables affect cancer detectability in the combined modality. Methods Between March and May 2012, paired FFDM and DBT images were obtained from 203 women as part of a diagnostic workup for breast cancer. Images from FFDM alone, DBT alone, and DBT combined with FFDM were reviewed in separate sessions by six blinded readers. Jackknife alternative free-response receiver operating characteristic (JAFROC) figure of merit (FOM), sensitivity, and specificity were compared between the modalities. Lesion characteristics affecting the cancer detection rate when using the combined modality were also analyzed. Results Among the 203 women, 126 women had a total of 129 malignancies and 77 women had total of 77 benign lesions. The overall JAFROC FOM of the combined modality was higher than that of FFDM alone (0.827 vs. 0.775, p<0.001) and that of DBT alone was higher than that of FFDM alone (0.807 vs. 0.775, p=0.027). The overall sensitivity of the combined modality was higher than that of FFDM alone (80.0% vs. 73.2%, p<0.001) and that of DBT alone was higher than that of FFDM alone (78.3% vs. 73.2%, p=0.007). Compared to FFDM alone, the combined modality detected an additional 48 cancers. Using the combined modality, the presence of masses or microcalcifications was significantly associated with the cancer detection rate (p<0.001). Conclusion The combination of DBT with FFDM results in a higher diagnostic yield than FFDM alone. Additionally, DBT alone performs better than FFDM alone. However, even when DBT is combined with FFDM, breast cancers with no discernible masses and those lacking calcifications are difficult to detect. PMID:28053633

  18. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2012-07-01 2012-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  19. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2011-07-01 2011-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  20. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2013-07-01 2013-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  1. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2014-07-01 2014-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  2. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Funding of field testing. 35.2262... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of field testing. In the case of grant assistance for field testing of innovative or alternative wastewater...

  3. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Funding of field testing. 35.2262... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of field testing. In the case of grant assistance for field testing of innovative or alternative wastewater...

  4. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Funding of field testing. 35.2262... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of field testing. In the case of grant assistance for field testing of innovative or alternative wastewater...

  5. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Funding of field testing. 35.2262... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of field testing. In the case of grant assistance for field testing of innovative or alternative wastewater...

  6. 40 CFR 35.2262 - Funding of field testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Funding of field testing. 35.2262... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works § 35.2262 Funding of field testing. In the case of grant assistance for field testing of innovative or alternative wastewater...

  7. Draft Test Guideline: Field Testing For Aquatic Organisms

    EPA Pesticide Factsheets

    The following draft test guideline is part of a series of test guidelines that have been developed by EPA for use in the testing of pesticides and toxic substances, and the development of test data for submission to the Agency for review.

  8. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  9. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  10. Field testing of asphalt-emulsion radon-barrier system

    SciTech Connect

    Hartley, J.N.; Freeman, H.D.; Baker, E.G.; Elmore, M.R.; Nelson, D.A.; Voss, C.F.; Koehmstedt, P.L.

    1981-09-01

    Three years of laboratory and field testing have demonstrated that asphalt emulsion seals are effective radon diffusion barriers. Both laboratory and field tests in 1979, 1980 and 1981 have shown that an asphalt emulsion seal can reduce radon fluxes by greater than 99.9%. The effective diffusion coefficient for the various asphalt emulsion admix seals averages about 10/sup -6/ cm/sup 2//s. The 1981 joint field test is a culmination of all the technology developed to date for asphalt emulsion radon barrier systems. Preliminary results of this field test and the results of the 1980 field test are presented. 18 figures, 6 tables.

  11. Nanoscale Electric Field Sensor-Development and Testing

    NASA Astrophysics Data System (ADS)

    Brame, Jon; Woods, Nathan

    2008-10-01

    The goal of this project is to test a carbon nanotube based electric field sensing device. The device consists of a miniature gold needle suspended on a mat of carbon nanotubes over a trench on a Si/Si02 substrate. Field tests were made by recording the electric field inside dust devils in a Nevada desert, and those electric fields were simulated in a lab environment. Further tests to determine the device sensitivity were performed by manually manipulating the gold needle with an Atomic Force Microscope (AFM) tip. We report on fabrication techniques, field and lab test results and AFM testing results.

  12. Deep Borehole Field Test Requirements and Controlled Assumptions.

    SciTech Connect

    Hardin, Ernest

    2015-07-01

    This document presents design requirements and controlled assumptions intended for use in the engineering development and testing of: 1) prototype packages for radioactive waste disposal in deep boreholes; 2) a waste package surface handling system; and 3) a subsurface system for emplacing and retrieving packages in deep boreholes. Engineering development and testing is being performed as part of the Deep Borehole Field Test (DBFT; SNL 2014a). This document presents parallel sets of requirements for a waste disposal system and for the DBFT, showing the close relationship. In addition to design, it will also inform planning for drilling, construction, and scientific characterization activities for the DBFT. The information presented here follows typical preparations for engineering design. It includes functional and operating requirements for handling and emplacement/retrieval equipment, waste package design and emplacement requirements, borehole construction requirements, sealing requirements, and performance criteria. Assumptions are included where they could impact engineering design. Design solutions are avoided in the requirements discussion. Deep Borehole Field Test Requirements and Controlled Assumptions July 21, 2015 iv ACKNOWLEDGEMENTS This set of requirements and assumptions has benefited greatly from reviews by Gordon Appel, Geoff Freeze, Kris Kuhlman, Bob MacKinnon, Steve Pye, David Sassani, Dave Sevougian, and Jiann Su.

  13. Field Accuracy Test of Rpas Photogrammetry

    NASA Astrophysics Data System (ADS)

    Barry, P.; Coakley, R.

    2013-08-01

    Baseline Surveys Ltd is a company which specialises in the supply of accurate geospatial data, such as cadastral, topographic and engineering survey data to commercial and government bodies. Baseline Surveys Ltd invested in aerial drone photogrammetric technology and had a requirement to establish the spatial accuracy of the geographic data derived from our unmanned aerial vehicle (UAV) photogrammetry before marketing our new aerial mapping service. Having supplied the construction industry with survey data for over 20 years, we felt that is was crucial for our clients to clearly understand the accuracy of our photogrammetry so they can safely make informed spatial decisions, within the known accuracy limitations of our data. This information would also inform us on how and where UAV photogrammetry can be utilised. What we wanted to find out was the actual accuracy that can be reliably achieved using a UAV to collect data under field conditions throughout a 2 Ha site. We flew a UAV over the test area in a "lawnmower track" pattern with an 80% front and 80% side overlap; we placed 45 ground markers as check points and surveyed them in using network Real Time Kinematic Global Positioning System (RTK GPS). We specifically designed the ground markers to meet our accuracy needs. We established 10 separate ground markers as control points and inputted these into our photo modelling software, Agisoft PhotoScan. The remaining GPS coordinated check point data were added later in ArcMap to the completed orthomosaic and digital elevation model so we could accurately compare the UAV photogrammetry XYZ data with the RTK GPS XYZ data at highly reliable common points. The accuracy we achieved throughout the 45 check points was 95% reliably within 41 mm horizontally and 68 mm vertically and with an 11.7 mm ground sample distance taken from a flight altitude above ground level of 90 m.The area covered by one image was 70.2 m × 46.4 m, which equals 0.325 Ha. This finding has shown

  14. Field Testing the EUSO-SPB instrument

    NASA Astrophysics Data System (ADS)

    Eser, Johannes; Cummings, Austin; Gregg, Rachel; Krantz, Harry; Polonsky, Zach; Wiencke, Lawrence; JEM-EUSO Collaboration

    2017-01-01

    In September of 2016 the Extreme Universe Space Observatory on a super pressure balloon (EUSO-SPB) instrument was tested in the west Utah desert with a laser ``test beam'' system. Laser tracks were measured at distances of 24 km with the laser tilted away from the detector. This geometry is similar to the expected geometry of downward going cosmic ray air showers during the planned balloon flight. We describe the test beam system and the tests. We acknowledge support of NASA grants NNX13AH55G, NNX13AH53G.

  15. Langevin simulation of scalar fields: Additive and multiplicative noises and lattice renormalization

    NASA Astrophysics Data System (ADS)

    Cassol-Seewald, N. C.; Farias, R. L. S.; Fraga, E. S.; Krein, G.; Ramos, Rudnei O.

    2012-08-01

    We consider the Langevin lattice dynamics for a spontaneously broken λϕ4 scalar field theory where both additive and multiplicative noise terms are incorporated. The lattice renormalization for the corresponding stochastic Ginzburg-Landau-Langevin and the subtleties related to the multiplicative noise are investigated.

  16. Additional Enhancement of Electric Field in Surface-Enhanced Raman Scattering due to Fresnel Mechanism

    NASA Astrophysics Data System (ADS)

    Jayawardhana, Sasani; Rosa, Lorenzo; Juodkazis, Saulius; Stoddart, Paul R.

    2013-08-01

    Surface-enhanced Raman scattering (SERS) is attracting increasing interest for chemical sensing, surface science research and as an intriguing challenge in nanoscale plasmonic engineering. Several studies have shown that SERS intensities are increased when metal island film substrates are excited through a transparent base material, rather than directly through air. However, to our knowledge, the origin of this additional enhancement has never been satisfactorily explained. In this paper, finite difference time domain modeling is presented to show that the electric field intensity at the dielectric interface between metal particles is higher for ``far-side'' excitation than ``near-side''. This is reasonably consistent with the observed enhancement for silver islands on SiO2. The modeling results are supported by a simple analytical model based on Fresnel reflection at the interface, which suggests that the additional SERS signal is caused by near-field enhancement of the electric field due to the phase shift at the dielectric interface.

  17. CALIPERS. Planning the Systems Approach to Field Testing Educational Products.

    ERIC Educational Resources Information Center

    Southwest Educational Development Lab., Austin, TX.

    Field testing, the last step in the developmental cycle for educational products, must ascertain whether the test product, placed in a natural environment, will actually elicit the behavioral changes it was designed to effect. A systems approach to field testing requires that certain basic areas of investigation first be established. Specific…

  18. Magnetic Field Apparatus (MFA) Hardware Test

    NASA Technical Reports Server (NTRS)

    Anderson, Ken; Boody, April; Reed, Dave; Wang, Chung; Stuckey, Bob; Cox, Dave

    1999-01-01

    The objectives of this study are threefold: (1) Provide insight into water delivery in microgravity and determine optimal germination paper wetting for subsequent seed germination in microgravity; (2) Observe the behavior of water exposed to a strong localized magnetic field in microgravity; and (3) Simulate the flow of fixative (using water) through the hardware. The Magnetic Field Apparatus (MFA) is a new piece of hardware slated to fly on the Space Shuttle in early 2001. MFA is designed to expose plant tissue to magnets in a microgravity environment, deliver water to the plant tissue, record photographic images of plant tissue, and deliver fixative to the plant tissue.

  19. Laboratory and field testing of improved geothermal rock bits

    SciTech Connect

    Hendrickson, R.R.; Jones, A.H.; Winzenried, R.W.; Maish, A.B.

    1980-07-01

    The development and testing of 222 mm (8-3/4 inch) unsealed, insert type, medium hard formation, high-temperature bits are described. The new bits were fabricated by substituting improved materials in critical bit components. These materials were selected on bases of their high temperature properties, machinability, and heat treatment response. Program objectives required that both machining and heat treating could be accomplished with existing rock bit production equipment. Two types of experimental bits were subjected to laboratory air drilling tests at 250/sup 0/C (482/sup 0/F) in cast iron. These tests indicated field testing could be conducted without danger to the hole, and that bearing wear would be substantially reduced. Six additional experimental bits, and eight conventional bits were then subjected to air drilling a 240/sup 0/C (464/sup 0/F) in Francisan Graywacke at The Geysers, CA. The materials selected improved roller wear by 200%, friction-pin wear by 150%, and lug wear by 150%. Geysers drilling performances compared directly to conventional bits indicate that in-gage drilling life was increased by 70%. All bits at The Geysers are subjected to reaming out-of-gage hole prior to drilling. Under these conditions the experimental bits showed a 30% increase in usable hole over the conventional bits. These tests demonstrated a potential well cost reduction of 4 to 8%. Savings of 12% are considered possible with drilling procedures optimized for the experimental bits.

  20. Testing and commercialization of byproduct dibasic acids as buffer additives for limestone flue gas desulfurization systems

    SciTech Connect

    Chang, J.C.S.; Mobley, J.D.

    1983-10-01

    Pilot plant (0.1 MW) tests and utility boiler full scale demonstration (194 MW) of byproduct organic dibasic acids (DBA) as buffer additives to limestone scrubbers have shown performance improvements equivalent to those achieved by the addition of pure adipic acid. Both SO/sub 2/ removal efficiency and limestone utilization increased, and no significant operating problems were observed with three of the four DBA tested. Chemical and biological evaluations of scrubber samples taken during the DBA testing indicated no detectable toxicity or mutagenicity, and no significant environmental impact is expected as a result of DBA addition. Economic estimates indicate that substitution of DBA for pure adipic acid as a buffer additive will result in additive cost savings of 30% or greater.

  1. Matching of additive and polarizable force fields for multiscale condensed phase simulations

    PubMed Central

    Baker, Christopher M.; Best, Robert B.

    2013-01-01

    Inclusion of electronic polarization effects is one of the key aspects in which the accuracy of current biomolecular force fields may be improved. The principal drawback of such approaches is the computational cost, which typically ranges from 3 – 10 times that of the equivalent additive model, and may be greater for more sophisticated treatments of polarization or other many-body effects. Here, we present a multiscale approach which may be used to enhance the sampling in simulations with polarizable models, by using the additive model as a tool to explore configuration space. We use a method based on information theory to determine the charges for an additive model that has optimal overlap with the polarizable one, and we demonstrate the feasibility of enhancing sampling via a hybrid replica exchange scheme for several model systems. An additional advantage is that, in the process, we obtain a systematic method for deriving charges for an additive model that will be the natural complement to its polarizable parent. The additive charges are found by an effective coarse-graining of the polarizable force field, rather than by ad hoc procedures. PMID:23997691

  2. Multiphase pumping: The lessons of long-term field testing

    SciTech Connect

    Elf-Aquitaine, E.L.; Taiani, S.

    1995-12-31

    The field testing of a POSEIDON rotodynamic helicoaxial pump (P302) manufactured by SULZER is being conducted since June 1994 on the Elf Aquitaine`s onshore site of the PECORADE oil field located in the south-west of France. This one-year testing program is aimed at qualifying this design of multiphase pump for future field applications. The multiphase pump has been previously tested at the IFP`s test loop of SOLAIZE for factory acceptance and performance test. This paper describes the PECORADE multiphase loop, the multiphase pump testing procedures and the results obtained in the field of performance, sensitivity, and endurance. The operational and maintenance lessons to be learned from this long-term field testing are presented from the point of view of the operator.

  3. A test strategy for the assessment of additive attributed toxicity of tobacco products.

    PubMed

    Kienhuis, Anne S; Staal, Yvonne C M; Soeteman-Hernández, Lya G; van de Nobelen, Suzanne; Talhout, Reinskje

    2016-08-01

    The new EU Tobacco Product Directive (TPD) prohibits tobacco products containing additives that are toxic in unburnt form or that increase overall toxicity of the product. This paper proposes a strategy to assess additive attributed toxicity in the context of the TPD. Literature was searched on toxicity testing strategies for regulatory purposes from tobacco industry and governmental institutes. Although mainly traditional in vivo testing strategies have been applied to assess toxicity of unburnt additives and increases in overall toxicity of tobacco products due to additives, in vitro tests combined with toxicogenomics and validated using biomarkers of exposure and disease are most promising in this respect. As such, tests are needed that are sensitive enough to assess additive attributed toxicity above the overall toxicity of tobacco products, which can associate assay outcomes to human risk and exposure. In conclusion, new, sensitive in vitro assays are needed to conclude whether comparable testing allows for assessment of small changes in overall toxicity attributed to additives. A more pragmatic approach for implementation on a short-term is mandated lowering of toxic emission components. Combined with risk assessment, this approach allows assessment of effectiveness of harm reduction strategies, including banning or reducing of additives.

  4. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  5. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  6. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  7. 76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-21

    ... AGENCY 40 CFR Part 80 RIN 2060-AP17 Regulation of Fuel and Fuel Additives: Alternative Test Method for... alternative test method for olefin content in gasoline. This final rule will provide flexibility to the... environmental benefits achieved from our fuels programs. ] DATES: This rule is effective November 21,...

  8. Leach testing of in situ stabilization grouts containing additives to sequester contaminants

    SciTech Connect

    Serne, R.J.; Ames, L.L.; Martin, P.F.C.; LeGore, V.L.; Lindenmeier, C.W.; Phillips, S.J.

    1993-04-01

    This document discusses laboratory testing performed by Pacific Northwest Laboratory (PNL) for Westinghouse Hanford Company (WHC) of special grout formulations that incorporate specific sequestering agents to help improve the ability of the cement to resist contaminant leaching. To enhance the sequestering of contaminants we chose five additives to introduce (singly) to the control cement. The additives were Florida pebble phosphate, clinoptilolite (a natural zeolite), ferrous sulfide (a reductant), a mixed bed organic ion exchange resin and a proprietary anion-adsorbing mixed metal oxide. These additives were added one per test to the standard formulation and used to encapsulate a diluted high-salt alkaline liquid waste that is produced after various processes to remove uranium and plutonium from spent nuclear fuel. This report documents the testing of these additives.

  9. Effect of Mg or Ag addition on the evaporation field of Al.

    PubMed

    Aruga, Yasuhiro; Nako, Hidenori; Tsuneishi, Hidemasa; Hasegawa, Yuki; Tao, Hiroaki; Ichihara, Chikara; Serizawa, Ai

    2013-09-01

    It is known that the distribution of the charge-states as well as the evaporation field shift to higher values as the specimen temperature is decreased at a constant rate of evaporation. This study has explored the effect of Mg or Ag addition on the evaporation field of Al in terms of the charge state distribution of the field evaporated Al ions. The fractional abundance of Al(2+) ions with respect to the total Al ions in Al-Mg alloy is lower than that in pure Al, whereas it shows higher level in the Al-Ag alloy at lower temperatures. The temperature dependence of the fractional abundance of Al(2+) ions has been also confirmed, suggesting that Al atoms in the Al-Mg alloy need lower evaporation field, while higher field is necessary to evaporate Al atoms in the Al-Ag alloy, compared with pure Al. This tendency is in agreement with that of the evaporation fields estimated theoretically by means of measurements of the work function and calculations of the binding energy of the pure Al, Al-Mg and Al-Ag alloys.

  10. Rapid Field Toxicity Test for Water Supplies

    DTIC Science & Technology

    1994-02-28

    four hours to allow toxins to react with the cells, bioluminescent bacteria , and for the cells to regain their ight-producing powers. In 1993, the...chart bioluminescent bacteria . recorder, where it is depicted as a cumulative curve (Fig. 5). Mud testing uses the suspended particulate phase (SPP, Fig...in perfect Correlation with the bioluminescent bacteria assay agreement. Correlation of E50 with LC50 is shown (Fig. 10) is good below an EC50 (half

  11. Field Lysimeter Test Facility: Second year (FY 1989) test results

    SciTech Connect

    Campbell, M.D.; Gee, G.W.; Kanyid, M.J.; Rockhold, M.L.

    1990-04-01

    The Record of Decision associated with the Hanford Defense Waste Environmental Impact Statement (53 FR 12449-53) commits to an evaluation of the use of protective barriers placed over near-surface wastes. The barrier must protect against wind and water erosion and limit plant and animal intrusion and infiltration of water. Successful conclusion of this program will yield the necessary protective barrier design for near-surface waste isolation. This report presents results from the second year of tests at the FLTF. The primary objective of testing protective barriers at the FLTF was to measure the water budgets within the various barriers and assess the effectiveness of their designs in limiting water intrusion into the zone beneath each barrier. Information obtained from these measurements is intended for use in refining barrier designs. Four elements of water budget were measured during the year: precipitation, evaporation, storage, and drainage. Run-off, which is a fifth element of a complete water budget, was made negligible by a lip on the lysimeters that protrudes 5 cm above the soil surface to prevent run-off. A secondary objective of testing protective barriers at the FLTF was to refine procedures and equipment to support data collection for verification of the computer model needed for long-term projections of barrier performance. 6 refs.

  12. Hydro-Balanced Stuffing Box field test

    SciTech Connect

    Giangiacomo, L.A.

    1999-05-28

    The Hydro-Balanced Stuffing Box is a seal assembly for polished rod pumping installations commonly used in oil and gas pumping well installations to contain produced well fluids. The improved stuffing box was developed and patented by Harold H. Palmour of The Palmour Group of Livingston, TX. The stuffing box is designed to reduce the incidence of seal leakage and to utilize an environmentally safe fluid, so that if there is any leakage, environmental damage is reduced or eliminated. The unit was tested on two wells at the Rocky Mountain Oilfield Testing Center. During the test period, the performance of the stuffing box was measured by monitoring the pressure on the tubing and the inner chamber with a Barton Two-pen recorder. The amount of safe fluid consumed, fluid leakage at the top of the stuffing box, pressure supplied from the nitrogen bottle, ambient temperature, and polish rod temperature was recorded. The stuffing box is capable of providing a better seal between well fluids an d the environment than conventional stuffing boxes. It allows the polished rod to operate cooler and with lubrication, extending the life of the packing elements, and reducing the amount of attention required to prevent leakage.

  13. Hybrid Residual Flexibility/Mass-Additive Method for Structural Dynamic Testing

    NASA Technical Reports Server (NTRS)

    Tinker, M. L.

    2003-01-01

    A large fixture was designed and constructed for modal vibration testing of International Space Station elements. This fixed-base test fixture, which weighs thousands of pounds and is anchored to a massive concrete floor, initially utilized spherical bearings and pendulum mechanisms to simulate Shuttle orbiter boundary constraints for launch of the hardware. Many difficulties were encountered during a checkout test of the common module prototype structure, mainly due to undesirable friction and excessive clearances in the test-article-to-fixture interface bearings. Measured mode shapes and frequencies were not representative of orbiter-constrained modes due to the friction and clearance effects in the bearings. As a result, a major redesign effort for the interface mechanisms was undertaken. The total cost of the fixture design, construction and checkout, and redesign was over $2 million. Because of the problems experienced with fixed-base testing, alternative free-suspension methods were studied, including the residual flexibility and mass-additive approaches. Free-suspension structural dynamics test methods utilize soft elastic bungee cords and overhead frame suspension systems that are less complex and much less expensive than fixed-base systems. The cost of free-suspension fixturing is on the order of tens of thousands of dollars as opposed to millions, for large fixed-base fixturing. In addition, free-suspension test configurations are portable, allowing modal tests to be done at sites without modal test facilities. For example, a mass-additive modal test of the ASTRO-1 Shuttle payload was done at the Kennedy Space Center launch site. In this Technical Memorandum, the mass-additive and residual flexibility test methods are described in detail. A discussion of a hybrid approach that combines the best characteristics of each method follows and is the focus of the study.

  14. Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

    NASA Technical Reports Server (NTRS)

    Zusack, Steven

    2016-01-01

    I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM

  15. Nevada Test Site field trip guidebook 1984

    SciTech Connect

    Dockery, H.A.; Byers, F.M. Jr.; Orkild, P.P.

    1985-04-01

    The Nevada Test Site (NTS), located in southern Nevada, was established in 1950 as an area for testing nuclear devices. Various geologic studies performed in conjunction with these activities as well as recent work on a proposed radioactive waste repository are reported in detail in this guidebook and include studies on the structure, stratigraphy, geochemistry, and physical properties of the rocks at NTS. The oldest sequence of rocks exposed in the NTS region is comprised of late Precambrian to Permian miogeoclinal rocks which were subsequently deformed during Jura-Cretaceous contraction, probably related to the Sevier orogeny. These rocks were then locally intruded by late Mesozoic (approx.93 m.y.BP) plutonic rocks related to the Sierra Nevada batholith. Voluminous calcalkaline ash-flow tuffs and associated volcanic rocks originating from the Timber Mountain-Oasis Valley caldera complex were extruded over much of NTS and adjacent areas from approx.16 to 10 m.y.BP. Peralkaline rocks intercalated in the volcanic sequence issued from both Silent Canyon (15 to 13 m.y.BP) and Black Mountain (9 to 7 m.y.BP) volcanic centers. The youngest igneous rocks at NTS are composed of basaltic rocks, primarily hawaiite, the older of which are associated with the evolving silicic volcanic centers and the younger associated with Cenozoic regional extension. Late Tertiary to Recent alluvium derived from the ranges form large, coalescing fans which fill the basins with sediments and reach thicknesses of over 1 km. 45 refs., 21 figs.

  16. FSA field test report, 1980 - 1982

    NASA Technical Reports Server (NTRS)

    Maxwell, H. G.; Grimmett, C. A.; Repar, J.; Frickland, P. O.; Amy, J. A.

    1983-01-01

    Photovoltaic modules made of new and developing materials were tested in a continuing study of weatherability, compatibility, and corrosion protection. Over a two-year period, 365 two-cell submodules have been exposed for various intervals at three outdoor sites in Southern California or subjected to laboratory acceptance tests. Results to date show little loss of maximum power output, except in two types of modules. In the first of these, failure is due to cell fracture from the stresses that arise as water is regained from the surrounding air by a hardboard substrate, which shrank as it dried during its encapsulation in plastic film at 150 C in vacuo. In the second, the glass superstrate is sensitive to cracking, which also damages the cells electrostatically bonded to it; inadequate bonding of interconnects to the cells is also a problem in these modules. In a third type of module, a polyurethane pottant has begun to yellow, though as yet without significant effect on maximum power output.

  17. Test particle acceleration in turbulent reconnecting magnetic fields

    NASA Technical Reports Server (NTRS)

    Ambrosiano, John; Matthaeus, William H.; Goldstein, Melvyn L.; Plante, Daniel

    1988-01-01

    The effect of turbulence on particle acceleration in a MHD field was investigated by computing test particle trajectories in turbulent MHD reconnecting fields, including reconnection simulations at different magnetic Reynolds numbers. The dynamics of individual particles were investigated making it possible to examine the acceleration mechanism in great detail. It was found that turbulence influences the acceleration in two ways. It enhances the reconnection electric field while producing a stochastic electric field that gives rise to momentum diffusion; and it produces magnetic 'bubbles' and other irregularities that can temporarily trap test particles in the strong reconnection electric field for times comparable to the magnetofluid characteristic time.

  18. Unraveling complex hydrogeologic systems using field tracer tests

    NASA Astrophysics Data System (ADS)

    Dam, William A.; Nicholson, Thomas

    Tracking the movement of underground contaminants is vital to protecting public health and the environment worldwide. Scientific efforts using field tracer techniques to solve contaminant migration problems are rapidly evolving to fill critical information gaps and provide confirmation of laboratory data and numerical models. Various chemical tracers are being used to formulate and evaluate alternative conceptual hydrogeologic modelssemi; namely, to constrain hydraulic properties of geologic systems, identify sources of groundwater, flow paths, and rates, and determine mechanisms that affect contaminant transport. Naturally occurring elements and environmental isotopes from atmospheric and underground nuclear testing can make excellent tracers. In addition, characterizing sites of future waste disposal, such as the potential high-level nuclear waste repository at Yucca Mountain, requires new and innovative techniques like injecting surrogate tracers that simulate potential contaminants and shed light on mechanisms that could control future contaminant migration.

  19. Brahms Mobile Agents: Architecture and Field Tests

    NASA Technical Reports Server (NTRS)

    Clancey, William J.; Sierhuis, Maarten; Kaskiris, Charis; vanHoof, Ron

    2002-01-01

    We have developed a model-based, distributed architecture that integrates diverse components in a system designed for lunar and planetary surface operations: an astronaut's space suit, cameras, rover/All-Terrain Vehicle (ATV), robotic assistant, other personnel in a local habitat, and a remote mission support team (with time delay). Software processes, called agents, implemented in the Brahms language, run on multiple, mobile platforms. These mobile agents interpret and transform available data to help people and robotic systems coordinate their actions to make operations more safe and efficient. The Brahms-based mobile agent architecture (MAA) uses a novel combination of agent types so the software agents may understand and facilitate communications between people and between system components. A state-of-the-art spoken dialogue interface is integrated with Brahms models, supporting a speech-driven field observation record and rover command system (e.g., return here later and bring this back to the habitat ). This combination of agents, rover, and model-based spoken dialogue interface constitutes a personal assistant. An important aspect of the methodology involves first simulating the entire system in Brahms, then configuring the agents into a run-time system.

  20. Test of QED at critical field strength

    SciTech Connect

    Bula, C.

    1997-01-01

    In a new experiment at the Final Focus Test Beam at SLAC, a low-emittance 46.6 GeV electron beam is brought into collisions with terawatt pulses of 1054 nm or 527 nm wavelength from a Nd:glass laser. Peak laser intensities of 10{sup 18} W/cm{sup 2} have been achieved corresponding to a value of 0.6 for the parameter {eta} = e{epsilon}/m{omega}{sub 0}c. In this case, an electron that crosses the center of the laser pulse has near-unit interaction probability. Results are presented for multiphoton Compton scattering in which an electron interacts with up to four laser photons, in agreement with theoretical calculations.

  1. Test of QED at critical field strength

    SciTech Connect

    Bula, C.; E-144 Collaboration

    1996-10-01

    In a new experiment at the Final Focus Test Beam at SLAC, a low-emittance 46.6 GeV electron beam is brought into collision with terawatt pulses of 1,054 nm or 527 nm wavelength from a Nd:glass laser. Peak laser intensities of 10{sup 18} W/cm{sup 2} have been achieved corresponding to a value of 0.6 for the parameter {eta} = e{var_epsilon}m{omega}{sub 0}c. In this case, an electron that crosses the center of the laser pulse has near-unit interaction probability. Results are presented for multiphoton Compton scattering in which an electron interacts with up to four laser photons, in agreement with theoretical calculations.

  2. FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

    SciTech Connect

    Susan S. Sorini; John F. Schabron; Joseph F. Rovani, Jr.

    2002-09-30

    Western Research Institute (WRI) has developed a new commercial product ready for technology transfer, the Diesel Dog{reg_sign} Portable Soil Test Kit, for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to the technology by taking the method through the American Society for Testing and Materials (ASTM) approval and validation processes. The method is designated as ASTM Method D 5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In June 2001, the Diesel Dog technology won an American Chemical Society Regional Industrial Innovations Award. To gain field experience with the new technology, Diesel Dog kits have been used for a variety of site evaluation and cleanup activities. Information gained from these activities has led to improvements in hardware configurations and additional insight into correlating Diesel Dog results with results from laboratory methods. The Wyoming Department of Environmental Quality (DEQ) used Diesel Dog Soil Test Kits to guide cleanups at a variety of sites throughout the state. ENSR, of Acton, Massachusetts, used a Diesel Dog Portable Soil Test Kit to evaluate sites in the Virgin Islands and Georgia. ChemTrack and the U.S. Army Corps of Engineers successfully used a test kit to guide excavation at an abandoned FAA fuel-contaminated site near Fairbanks, Alaska. Barenco, Inc. is using a Diesel Dog Portable Soil Test Kit for site evaluations in Canada. A small spill of diesel fuel was cleaned up in Laramie, Wyoming using a Diesel

  3. Additional Enhancement of Electric Field in Surface-Enhanced Raman Scattering due to Fresnel Mechanism

    PubMed Central

    Jayawardhana, Sasani; Rosa, Lorenzo; Juodkazis, Saulius; Stoddart, Paul R.

    2013-01-01

    Surface-enhanced Raman scattering (SERS) is attracting increasing interest for chemical sensing, surface science research and as an intriguing challenge in nanoscale plasmonic engineering. Several studies have shown that SERS intensities are increased when metal island film substrates are excited through a transparent base material, rather than directly through air. However, to our knowledge, the origin of this additional enhancement has never been satisfactorily explained. In this paper, finite difference time domain modeling is presented to show that the electric field intensity at the dielectric interface between metal particles is higher for “far-side” excitation than “near-side”. This is reasonably consistent with the observed enhancement for silver islands on SiO2. The modeling results are supported by a simple analytical model based on Fresnel reflection at the interface, which suggests that the additional SERS signal is caused by near-field enhancement of the electric field due to the phase shift at the dielectric interface. PMID:23903714

  4. Addition of carbon sorbents to reduce PCB and PAH bioavailability in marine sediments: physicochemical tests.

    PubMed

    Zimmerman, John R; Ghosh, Upal; Millward, Rod N; Bridges, Todd S; Luthy, Richard G

    2004-10-15

    The addition of activated carbon as particulate sorbent to the biologically active layer of contaminated sediment is proposed as an in-situ treatment method to reduce the chemical and biological availability of hydrophobic organic contaminants (HOCs) such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs). We report results from physicochemical experiments that assess this concept. PCB- and PAH-contaminated sediment from Hunters Point Naval Shipyard, San Francisco Bay, CA, was contacted with coke and activated carbon for periods of 1 and 6 months. Sediment treated with 3.4 wt % activated carbon showed 92% and 84% reductions in aqueous equilibrium PCB and PAH concentrations, 77% and 83% reductions in PCB and PAH uptake by semipermeable membrane devices (SPMD), respectively, and reductions in PCB flux to overlying water in quiescent systems up to 89%. Adding coke to contaminated sediment did not significantly decrease aqueous equilibrium PCB concentrations nor PCB or PAH availability in SPMD measurements. Coke decreased PAH aqueous equilibrium concentrations by 38-64% depending on coke dose and particle size. The greater effectiveness of activated carbon as compared to coke is attributed to its much greater specific surface area and a pore structure favorable for binding contaminants. The results from the physicochemical tests suggest that adding activated carbon to contaminated field sediment reduces HOC availability to the aqueous phase. The benefit is manifested relatively quickly under optimum contact conditions and improves in effectiveness with contact time from 1 to 6 months. Activated carbon application is a potentially attractive method for in-situ, nonremoval treatment of marine sediment contaminated with HOCs.

  5. Optomap ultrawide field imaging identifies additional retinal abnormalities in patients with diabetic retinopathy

    PubMed Central

    Price, Liam D; Au, Stephanie; Chong, N Victor

    2015-01-01

    Purpose To compare diabetic retinopathy (DR) severity grading between Optomap ultrawide field scanning laser ophthalmoscope (UWFSLO) 200° images and an Early Treatment Diabetic Retinopathy Study (ETDRS) seven-standard field view. Methods Optomap UWFSLO images (total: 266) were retrospectively selected for evidence of DR from a database of eye clinic attendees. The Optomap UWFSLO images were graded for DR severity by two masked assessors. An ETDRS seven-field mask was overlaid on the Optomap UWFSLO images, and the DR grade was assessed for the region inside the mask. Any interassessor discrepancies were adjudicated by a senior retinal specialist. Kappa agreement levels were used for statistical analysis. Results Fifty images (19%) (P<0.001) were assigned a higher DR level in the Optomap UWFSLO view compared to the ETDRS seven-field view, which resulted in 40 images (15%) (P<0.001) receiving a higher DR severity grade. DR severity grades in the ETDRS seven-field view compared with the Optomap UWFSLO view were identical in 85% (226) of the images and within one severity level in 100% (266) of the images. Agreement between the two views was substantial: unweighted κ was 0.74±0.04 (95% confidence interval: 0.67–0.81) and weighted κ was 0.80±0.03 (95% confidence interval: 0.74–0.86). Conclusion Compared to the ETDRS seven-field view, a significant minority of patients are diagnosed with more severe DR when using the Optomap UWFSLO view. The clinical significance of additional peripheral lesions requires evaluation in future prospective studies using large cohorts. PMID:25848202

  6. The force-field derivation and application of explosive/additive interfaces

    NASA Astrophysics Data System (ADS)

    Long, Yao; Chen, Jun

    2016-10-01

    The inter-molecular force-field across RDX/(paraffin, fluoropolymer) interfaces are derived from first-principles calculated energies under the GGA+vdW functional. Based on the force-field, the polycrystal structures of mixture explosives are obtained, and a set of thermodynamic properties are calculated, including the elastic constants, thermal expansion coefficient, heat capacity, isothermal curve and the Hugoniot curve. The results are in good agreement with the available experiments, and provide a reasonable prediction about the properties of plastic bonded explosives. We find that the thermal expansion coefficient of a multi-component explosive is not only determined by the properties of the components, but is also affected by the thermal stress at the explosive/additive interfaces.

  7. Photon-assisted field emission from a Si tip at addition of an AC low voltage

    NASA Astrophysics Data System (ADS)

    Zaporozhchenko, A. V.; Chernov, S. V.; Odnodvorets, L. V.; Stetsenko, B. V.; Nepijko, S. A.; Elmers, H. J.; Schönhense, G.

    2015-07-01

    We investigated the field emission current from a p-type silicon tip with large resistivity of 4 × 103 Ω cm for light illumination with a photon energy of 1.3 eV and tip-anode voltages of 0.7-5.0 kV. Additional AC voltage with amplitude 30-60 V and frequency varying in the range of 10-107 Hz was applied to the tip which resulted in variations of emission current. We investigated the dependence of this phenomenon on the AC signal parameters, light intensity and temperature. The resonant-like frequency dependence of the emission current is because the tip acts as a driven plasmonic resonator. The results represent an important step forward for the development of high-frequency display systems based on electron field emission.

  8. Probe Station and Near-Field Scanner for Testing Antennas

    NASA Technical Reports Server (NTRS)

    Zaman, Afroz; Lee, Richard Q.; Darby, William G.; Barr, Philip J.; Miranda, Felix A.; Lambert, Kevin

    2006-01-01

    A facility that includes a probe station and a scanning open-ended waveguide probe for measuring near electromagnetic fields has been added to Glenn Research Center's suite of antenna-testing facilities, at a small fraction of the cost of the other facilities. This facility is designed specifically for nondestructive characterization of the radiation patterns of miniaturized microwave antennas fabricated on semiconductor and dielectric wafer substrates, including active antennas that are difficult to test in traditional antenna-testing ranges because of fragility, smallness, or severity of DC-bias or test-fixture requirements. By virtue of the simple fact that a greater fraction of radiated power can be captured in a near-field measurement than in a conventional far-field measurement, this near-field facility is convenient for testing miniaturized antennas with low gains.

  9. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Reasonable and representative tests and recordkeeping requirements-additional requirements. 1631.32 Section 1631.32 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF...

  10. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Reasonable and representative tests and recordkeeping requirements-additional requirements. 1631.32 Section 1631.32 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF...

  11. Biodegradability testing of synthetic ester lubricants--effects of additives and usage.

    PubMed

    Eisentraeger, Adolf; Schmidt, Martin; Murrenhoff, Hubertus; Dott, Wolfgang; Hahn, Stefan

    2002-07-01

    The optimised biodegradability test system "O2/CO2 Headspace Test with GC-TCD" is used for the assessment of synthetic ester lubricants. The effects of both additives and usage on biodegradability are examined and discussed. Ester based cutting fluids and hydraulic fluids with and without additives are used under defined conditions at machine tools and hydraulic and plain bearing test benches. The lubricants are characterised additionally with respect to kinematic viscosity, acidity and elemental composition. Furthermore, a formulated mineral oil is characterised before and after usage at an hydraulic test bench. The results clearly show that the mineral oil is far less biodegradable than the ester oils and that their biodegradability is not affected by usage. Biodegradability of the ester oils is mainly depending on the characteristics of the base fluids and not affected by the additives. Antioxidants are influencing stability respectively biodegradability indirectly, since they prevent oxopolymerisation effects. Other effects of usage on biodegradation are not detected. In this context, the antioxidants ensure ready biodegradability and have a positive effect on the environmental fate of synthetic ester lubricants.

  12. Testing for departures from additivity in mixtures of perfluoroalkyl acids (PFAAs)

    EPA Science Inventory

    This study is a follow-up to a paper by Carr, et al. that determined a design structure to optimally test for departures from additivity in a fixed ratio mixture of four perfluoroalkyl acids (PFAAs) using an in vitro transiently-transfected COS- 1 PPARa reporter model with an NHA...

  13. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  14. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  15. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  16. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  17. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  18. Cyp26 Enzymes Facilitate Second Heart Field Progenitor Addition and Maintenance of Ventricular Integrity

    PubMed Central

    Rydeen, Ariel B.; Waxman, Joshua S.

    2016-01-01

    Although retinoic acid (RA) teratogenicity has been investigated for decades, the mechanisms underlying RA-induced outflow tract (OFT) malformations are not understood. Here, we show zebrafish embryos deficient for Cyp26a1 and Cyp26c1 enzymes, which promote RA degradation, have OFT defects resulting from two mechanisms: first, a failure of second heart field (SHF) progenitors to join the OFT, instead contributing to the pharyngeal arch arteries (PAAs), and second, a loss of first heart field (FHF) ventricular cardiomyocytes due to disrupted cell polarity and extrusion from the heart tube. Molecularly, excess RA signaling negatively regulates fibroblast growth factor 8a (fgf8a) expression and positively regulates matrix metalloproteinase 9 (mmp9) expression. Although restoring Fibroblast growth factor (FGF) signaling can partially rescue SHF addition in Cyp26 deficient embryos, attenuating matrix metalloproteinase (MMP) function can rescue both ventricular SHF addition and FHF integrity. These novel findings indicate a primary effect of RA-induced OFT defects is disruption of the extracellular environment, which compromises both SHF recruitment and FHF ventricular integrity. PMID:27893754

  19. Cyp26 Enzymes Facilitate Second Heart Field Progenitor Addition and Maintenance of Ventricular Integrity.

    PubMed

    Rydeen, Ariel B; Waxman, Joshua S

    2016-11-01

    Although retinoic acid (RA) teratogenicity has been investigated for decades, the mechanisms underlying RA-induced outflow tract (OFT) malformations are not understood. Here, we show zebrafish embryos deficient for Cyp26a1 and Cyp26c1 enzymes, which promote RA degradation, have OFT defects resulting from two mechanisms: first, a failure of second heart field (SHF) progenitors to join the OFT, instead contributing to the pharyngeal arch arteries (PAAs), and second, a loss of first heart field (FHF) ventricular cardiomyocytes due to disrupted cell polarity and extrusion from the heart tube. Molecularly, excess RA signaling negatively regulates fibroblast growth factor 8a (fgf8a) expression and positively regulates matrix metalloproteinase 9 (mmp9) expression. Although restoring Fibroblast growth factor (FGF) signaling can partially rescue SHF addition in Cyp26 deficient embryos, attenuating matrix metalloproteinase (MMP) function can rescue both ventricular SHF addition and FHF integrity. These novel findings indicate a primary effect of RA-induced OFT defects is disruption of the extracellular environment, which compromises both SHF recruitment and FHF ventricular integrity.

  20. Field test of fiber optic hydrazine dosimeters at Cape Canaveral

    NASA Astrophysics Data System (ADS)

    Klimcak, Charles M.; Chan, Y.; Jaduszliwer, B.

    1999-02-01

    We tested seventy-two hydrazine fuel fiber optic dosimeters for periods up to three months or Cape Canaveral in order to determine the effect of the local environment on its lifetime and sensitivity. The dosimeters were deployed at a diverse group of sites including fuel, oxidizer, and hydrocarbon fuel storage and transfer locations, a salt spray corrosion test facility, a satellite processing area, an estuarine marsh, a paint storage locker, and several indoor locations including chemical laboratory fume hoods and bathrooms. In addition, a group were set aside in a sealed enclosure for control purposes. The dosimeters were retrieved at monthly intervals and exposed to measured doses of hydrazine vapor to determine the effects of the field exposure on their hydrazine response. Our analysis indicated that 90% of the exposed dosimeters were able to sense hydrazine at a dose detectivity of less than 15 ppb-hr, a value that meets the current hydrazine sensing requirement. Consequently, we are planning to deploy a full scale, continuously operating fiber optic system for detecting potential hydrazine leaks during launch operations at Cape Canaveral.

  1. Field-based physiological testing of wheelchair athletes.

    PubMed

    Goosey-Tolfrey, Victoria L; Leicht, Christof A

    2013-02-01

    The volume of literature on field-based physiological testing of wheelchair sports, such as basketball, rugby and tennis, is considerably smaller when compared with that available for individuals and team athletes in able-bodied (AB) sports. In analogy to the AB literature, it is recognized that performance in wheelchair sports not only relies on fitness, but also sport-specific skills, experience and technical proficiency. However, in contrast to AB sports, two major components contribute towards 'wheeled sports' performance, which are the athlete and the wheelchair. It is the interaction of these two that enable wheelchair propulsion and the sporting movements required within a given sport. Like any other athlete, participants of wheelchair sports are looking for efficient ways to train and/or analyse their technique and fitness to improve their performance. Consequently, laboratory and/or field-based physiological monitoring tools used at regular intervals at key time points throughout the year must be considered to help with training evaluation. The present review examines methods available in the literature to assess wheelchair sports fitness in a field-based environment, with special attention on outcome variables, validity and reliability issues, and non-physiological influences on performance. It also lays out the context of field-based testing by providing details about the Paralympic court sports and the impacts of a disability on sporting performance. Due to the limited availability of specialized equipment for testing wheelchair-dependent participants in the laboratory, the adoption of field-based testing has become the preferred option by team coaches of wheelchair athletes. An obvious advantage of field-based testing is that large groups of athletes can be tested in less time. Furthermore, athletes are tested in their natural environment (using their normal sports wheelchair set-up and floor surface), potentially making the results of such testing

  2. Photovoltaic-Powered Vaccine Refrigerator: Freezer Systems Field Test Results

    NASA Technical Reports Server (NTRS)

    Ratajczak, A. F.

    1985-01-01

    A project to develop and field test photovoltaic-powered refrigerator/freezers suitable for vaccine storage was undertaken. Three refrigerator/freezers were qualified; one by Solar Power Corp. and two by Solvolt. Follow-on contracts were awarded for 19 field test systems and for 10 field test systems. A total of 29 systems were installed in 24 countries between October 1981 and October 1984. The project, systems descriptions, installation experiences, performance data for the 22 systems for which field test data was reported, an operational reliability summary, and recommendations relative to system designs and future use of such systems are explained. Performance data indicate that the systems are highly reliable and are capable of maintaining proper vaccine storage temperatures in a wide range of climatological and user environments.

  3. Field Testing Research at the NWTC (Fact Sheet)

    SciTech Connect

    Not Available

    2015-02-01

    The National Wind Technology Center (NWTC) at the National Renewable Laboratory (NREL) has extensive field testing capabilities that have been used in collaboration with the wind industry to accelerate wind technology development and deployment for more than 30 years.

  4. Metrology test object for dimensional verification in additive manufacturing of metals for biomedical applications.

    PubMed

    Teeter, Matthew G; Kopacz, Alexander J; Nikolov, Hristo N; Holdsworth, David W

    2015-01-01

    Additive manufacturing continues to increase in popularity and is being used in applications such as biomaterial ingrowth that requires sub-millimeter dimensional accuracy. The purpose of this study was to design a metrology test object for determining the capabilities of additive manufacturing systems to produce common objects, with a focus on those relevant to medical applications. The test object was designed with a variety of features of varying dimensions, including holes, cylinders, rectangles, gaps, and lattices. The object was built using selective laser melting, and the produced dimensions were compared to the target dimensions. Location of the test objects on the build plate did not affect dimensions. Features with dimensions less than 0.300 mm did not build or were overbuilt to a minimum of 0.300 mm. The mean difference between target and measured dimensions was less than 0.100 mm in all cases. The test object is applicable to multiple systems and materials, tests the effect of location on the build, uses a minimum of material, and can be measured with a variety of efficient metrology tools (including measuring microscopes and micro-CT). Investigators can use this test object to determine the limits of systems and adjust build parameters to achieve maximum accuracy.

  5. Progress in crosswell induction imaging for EOR: field system design and field testing

    SciTech Connect

    Kirkendall, B A; Lewis, J P; Hunter, S L; Harben, P E

    1999-03-04

    At Lawrence Livermore National Laboratory (LLNL), we are continuing our effort to develop improved crosswell low-frequency electromagnetic imaging techniques, which are used to map in situ steamflood and waterflood movement during enhanced oil recovery (EOR) operations. Toward this effort, we procured two new borehole-logging field vehicles, and developed and integrated new crosswell electromagnetic transmitter and receiver data acquisition and control systems into these vehicles. We tested this new acquisition system by conducting a suite of background measurements and repeatability experiments at the Richmond Field Station in Richmond, California. Repeatability of a given scan in which the receiver was fixed and the transmitter position was varied over 60 m in 0.2-m increments resulted in amplitude differences of less than 0.6% and phase differences of less than 0.54 deg. Forward modeling produced a resistivity map fully consistent with well log data from the Richmond Field Station. In addition, modeling results suggest (1) that residual high-conductivity saltwater, injected in 1993 and pumped out in 1995, is present at the site and (2) that it has diffused outward from the original target strata. To develop crosswell electromagnetic imaging into a viable commercial product, our future research must be a two-fold approach: (1) improved quantification of system noise through experiments such as ferromagnetic core characterization as a function of temperature, and (2) development of procedures and codes to account for steel-cased hole scenarios.

  6. Influence of grid bar shape on field cleaner performance - field testing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A test was conducted to evaluate the influence of grid bar cross sectional shape on cotton stripper field cleaner performance in terms of cleaning efficiency, seed cotton loss, and fiber and yarn quality. Three field cleaner configurations were tested on a cotton stripper harvester operating under f...

  7. Perihelion advance of a test particle in the Kerr field.

    NASA Astrophysics Data System (ADS)

    Haque, Enamul

    2017-01-01

    Here I represent a Perihelion advance of a test particle in the Kerr field. I assume that the spin of the central body to be very small and planar motion occurs only in the equatorial plane. I find some physical picture which is different from the case of Schwarzschild field and can recover the picture for Schwarzschild field. We use perturbation method to solve the equation of motion.

  8. The Center-TRACON Automation System: Simulation and field testing

    NASA Technical Reports Server (NTRS)

    Denery, Dallas G.; Erzberger, Heinz

    1995-01-01

    A new concept for air traffic management in the terminal area, implemented as the Center-TRACON Automation System, has been under development at NASA Ames in a cooperative program with the FAA since 1991. The development has been strongly influenced by concurrent simulation and field site evaluations. The role of simulation and field activities in the development process will be discussed. Results of recent simulation and field tests will be presented.

  9. Field testing of the Alere DDS2 Mobile Test System for drugs in oral fluid.

    PubMed

    Moore, Christine; Kelley-Baker, Tara; Lacey, John

    2013-06-01

    A preliminary field evaluation of a second-generation handheld oral fluid testing device, the Alere DDS2 Mobile Test System (DDS2), is described. As part of a larger study, drivers were randomly stopped at various locations across California (in 2012) and asked to submit voluntarily to a questionnaire regarding their drug and alcohol use, a breath alcohol test and collection of oral fluid with the Quantisal device. The Quantisal-collected oral fluid samples were sent for laboratory-based analyses. At one location, 50 drivers were asked to submit an additional oral fluid sample using the DDS2 collection device; these samples were analyzed by using the DDS2 mobile test system. Thirty-eight donors (76%) provided specimens that were successfully run on the mobile system; in 12 cases (24%), the device failed to provide a valid result. Thirty-two of the 38 collected samples were negative for all drugs; five were positive for tetrahydrocannabinol and one was positive for methamphetamine using the mobile device. These results corresponded exactly with the laboratory-based results from the Quantisal oral fluid collection.

  10. Advanced Utility Mercury-Sorbent Field-Testing Program

    SciTech Connect

    Ronald Landreth

    2007-12-31

    This report summarizes the work conducted from September 1, 2003 through December 31, 2007 on the project entitled Advanced Utility Mercury-Sorbent Field-Testing Program. The project covers the testing at the Detroit Edison St. Clair Plant and the Duke Power Cliffside and Buck Stations. The St. Clair Plant used a blend of subbituminous and bituminous coal and controlled the particulate emissions by means of a cold-side ESP. The Duke Power Stations used bituminous coals and controlled their particulate emissions by means of hot-side ESPs. The testing at the Detroit Edison St. Clair Plant demonstrated that mercury sorbents could be used to achieve high mercury removal rates with low injection rates at facilities that burn subbituminous coal. A mercury removal rate of 94% was achieved at an injection rate of 3 lb/MMacf over the thirty day long-term test. Prior to this test, it was believed that the mercury in flue gas of this type would be the most difficult to capture. This is not the case. The testing at the two Duke Power Stations proved that carbon- based mercury sorbents can be used to control the mercury emissions from boilers with hot-side ESPs. It was known that plain PACs did not have any mercury capacity at elevated temperatures but that brominated B-PAC did. The mercury removal rate varies with the operation but it appears that mercury removal rates equal to or greater than 50% are achievable in facilities equipped with hot-side ESPs. As part of the program, both sorbent injection equipment and sorbent production equipment was acquired and operated. This equipment performed very well during this program. In addition, mercury instruments were acquired for this program. These instruments worked well in the flue gas at the St. Clair Plant but not as well in the flue gas at the Duke Power Stations. It is believed that the difference in the amount of oxidized mercury, more at Duke Power, was the difference in instrument performance. Much of the equipment was

  11. Development of a Specific Anaerobic Field Test for Aerobic Gymnastics

    PubMed Central

    Paineli, Vitor de Salles; Azevedo, Rafael de Almeida; Borelli, Claudia Cristine Gomes; Lancha Junior, Antônio Herbert; Gualano, Bruno; Artioli, Guilherme Giannini

    2015-01-01

    The current investigation aimed to develop a valid specific field test to evaluate anaerobic physical performance in Aerobic Gymnastics athletes. We first designed the Specific Aerobic Gymnast Anaerobic Test (SAGAT), which included gymnastics-specific elements performed in maximal repeated sprint fashion, with a total duration of 80-90 s. In order to validate the SAGAT, three independent sub-studies were performed to evaluate the concurrent validity (Study I, n=8), the reliability (Study II, n=10) and the sensitivity (Study III, n=30) of the test in elite female athletes. In Study I, a positive correlation was shown between lower-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.69, CI: -0.94 to 0.03 and Peak power: p = 0.02, r = -0.72, CI: -0.95 to -0.04) and between upper-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.67, CI: -0.94 to 0.02 and Peak power: p = 0.03, r = -0.69, CI: -0.94 to 0.03). Additionally, plasma lactate was similarly increased in response to SAGAT (p = 0.002), lower-body Wingate Test (p = 0.021) and a simulated competition (p = 0.007). In Study II, no differences were found between the time to complete the SAGAT in repeated trials (p = 0.84; Cohen’s d effect size = 0.09; ICC = 0.97, CI: 0.89 to 0.99; MDC95 = 0.12 s). Finally, in Study III the time to complete the SAGAT was significantly lower during the competition cycle when compared to the period before the preparatory cycle (p < 0.001), showing an improvement in SAGAT performance after a specific Aerobic Gymnastics training period. Taken together, these data have demonstrated that SAGAT is a specific, reliable and sensitive measurement of specific anaerobic performance in elite female Aerobic Gymnastics, presenting great potential to be largely applied in training settings. PMID:25876039

  12. Development of a specific anaerobic field test for aerobic gymnastics.

    PubMed

    Alves, Christiano Robles Rodrigues; Borelli, Marcello Tadeu Caetano; Paineli, Vitor de Salles; Azevedo, Rafael de Almeida; Borelli, Claudia Cristine Gomes; Lancha Junior, Antônio Herbert; Gualano, Bruno; Artioli, Guilherme Giannini

    2015-01-01

    The current investigation aimed to develop a valid specific field test to evaluate anaerobic physical performance in Aerobic Gymnastics athletes. We first designed the Specific Aerobic Gymnast Anaerobic Test (SAGAT), which included gymnastics-specific elements performed in maximal repeated sprint fashion, with a total duration of 80-90 s. In order to validate the SAGAT, three independent sub-studies were performed to evaluate the concurrent validity (Study I, n=8), the reliability (Study II, n=10) and the sensitivity (Study III, n=30) of the test in elite female athletes. In Study I, a positive correlation was shown between lower-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.69, CI: -0.94 to 0.03 and Peak power: p = 0.02, r = -0.72, CI: -0.95 to -0.04) and between upper-body Wingate test and SAGAT performance (Mean power: p = 0.03, r = -0.67, CI: -0.94 to 0.02 and Peak power: p = 0.03, r = -0.69, CI: -0.94 to 0.03). Additionally, plasma lactate was similarly increased in response to SAGAT (p = 0.002), lower-body Wingate Test (p = 0.021) and a simulated competition (p = 0.007). In Study II, no differences were found between the time to complete the SAGAT in repeated trials (p = 0.84; Cohen's d effect size = 0.09; ICC = 0.97, CI: 0.89 to 0.99; MDC95 = 0.12 s). Finally, in Study III the time to complete the SAGAT was significantly lower during the competition cycle when compared to the period before the preparatory cycle (p < 0.001), showing an improvement in SAGAT performance after a specific Aerobic Gymnastics training period. Taken together, these data have demonstrated that SAGAT is a specific, reliable and sensitive measurement of specific anaerobic performance in elite female Aerobic Gymnastics, presenting great potential to be largely applied in training settings.

  13. Radial distribution functions of non-additive hard sphere mixtures via Percus' test particle route.

    PubMed

    Hopkins, Paul; Schmidt, Matthias

    2011-08-17

    Using fundamental density functional theory we calculate the partial radial distribution functions, g(ij)(r), of a binary non-additive hard sphere mixture using either Percus' test particle approach or inversion of the analytic structure factor obtained via the Ornstein-Zernike route. We find good agreement between the theoretical results and Monte Carlo simulation data for both positive and moderate negative non-additivities. We investigate the asymptotic, [Formula: see text], decay of the g(ij)(r) and show that this agrees with the analytic analysis of the contributions to the partial structure factors in the plane of complex wavevectors. We find the test particle density profiles to be free of unphysical artefacts, contrary to earlier reports.

  14. Results of field tests of a transportable calorimeter assay system

    SciTech Connect

    Rakel, D.A.; Lemming, J.F.; Rodenburg, W.W.; Duff, M.F.; Jarvis, J.Y.

    1981-01-01

    A transportable calorimetric assay system, developed for use by US Department of Energy inspectors, is described. The results of field tests at three DOE sites are presented. The samples measured in these tests represent a variety of forms (ash, oxide, metal buttons), isotopic composition, and total plutonium content.

  15. Differential Gender Performance on the Major Field Test-Business

    ERIC Educational Resources Information Center

    Bielinska-Kwapisz, Agnieszka; Brown, F. William

    2013-01-01

    The Major Field Test in Business (MFT-B), a standardized assessment test of business knowledge among undergraduate business seniors, is widely used to measure student achievement. Many previous studies analyzing scores on the MFT-B report gender differences on the exam even after controlling for student's aptitude, general intellectual ability,…

  16. Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

    NASA Technical Reports Server (NTRS)

    Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

    2012-01-01

    Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility

  17. Automated particulate sampler field test model operations guide

    SciTech Connect

    Bowyer, S.M.; Miley, H.S.

    1996-10-01

    The Automated Particulate Sampler Field Test Model Operations Guide is a collection of documents which provides a complete picture of the Automated Particulate Sampler (APS) and the Field Test in which it was evaluated. The Pacific Northwest National Laboratory (PNNL) Automated Particulate Sampler was developed for the purpose of radionuclide particulate monitoring for use under the Comprehensive Test Ban Treaty (CTBT). Its design was directed by anticipated requirements of small size, low power consumption, low noise level, fully automatic operation, and most predominantly the sensitivity requirements of the Conference on Disarmament Working Paper 224 (CDWP224). This guide is intended to serve as both a reference document for the APS and to provide detailed instructions on how to operate the sampler. This document provides a complete description of the APS Field Test Model and all the activity related to its evaluation and progression.

  18. A field validation of two sediment-amphipod toxicity tests.

    PubMed

    Ferraro, Steven P; Cole, Faith A

    2002-07-01

    A field validation study of two sediment-amphipod toxicity tests was conducted using sediment samples collected subtidally in the vicinity of a polycyclic aromatic hydrocarbon (PAH)-contaminated Superfund site in Elliott Bay (WA, USA). Sediment samples were collected at 30 stations with a 0.1 m2 grab from which subsamples were taken for sediment toxicity testing and geochemical and macrofaunal analyses. Standard 10-d sediment-amphipod toxicity tests were conducted with Rhepoxynius abronius and Leptocheiros plumulosus. Sediments were analyzed for 33 PAHs, pentachlorophenol, polychlorinated biphenyls, acid-volatile sulfide, simultaneously extracted metals (Cd, Cu, Zn, Pb, Ni), total organic carbon, and grain size. Sediment temperature, oxygen-reduction potential, water depth, and interstitial water salinity were also measured. Polycyclic aromatic hydrocarbons, quantified as total PAH toxic units (TU(PAH)), were confirmed to be an important common causal agent of the changes in the two toxicity test (% survival R. abronius, % survival L. plumulosus) and five macrofaunal community (number of species, S; numerical abundance, A: total biomass, B: Swartz's dominance index, SDI; Brillouin's index, H) endpoints. Two other macrofaunal community metrics (the complement of Simpson's index, 1 - SI, and McIntosh's index, MI) were less sensitive to TU(PAH) than the two toxicity test endpoints. The sensitivities of R. abronius and L. plumulosus to TU(PAH) were statistically indistinguishable. Field validations were conducted by testing the association between or among each toxicity test endpoint, each of seven macrofaunal community metrics (S, A, B, SDI, H, 1 - SI, MI), and TU(PAH) by (1) Spearman's coefficient of rank correlation, (2) Kendall's coefficient of concordance, (3) G tests of independence, and (4) regression analysis. Some field validations based on multivariable tests of association (e.g., points 2 and 3) among toxicity test, field, and stressor endpoints produced

  19. Geomechanical Considerations for the Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Park, B. Y.

    2015-12-01

    Deep borehole disposal of high-level radioactive waste is under consideration as a potential alternative to shallower mined repositories. The disposal concept consists of drilling a borehole into crystalline basement rocks to a depth of 5 km, emplacement of canisters containing solid waste in the lower 2 km, and plugging and sealing the upper 3 km of the borehole. Crystalline rocks such as granites are particularly attractive for borehole emplacement because of their low permeability and porosity at depth, and high mechanical strength to resist borehole deformation. In addition, high overburden pressures contribute to sealing of some of the fractures that provide transport pathways. We present geomechanical considerations during construction (e.g., borehole breakouts, disturbed rock zone development, and creep closure), relevant to both the smaller-diameter characterization borehole (8.5") and the larger-diameter field test borehole (17"). Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  20. Delta undulator model: Magnetic field and beam test results

    NASA Astrophysics Data System (ADS)

    Temnykh, A.; Babzien, M.; Davis, D.; Fedurin, M.; Kusche, K.; Park, J.; Yakimenko, V.

    2011-09-01

    A novel type of in-vacuum Elliptical Polarization Undulator (EPU) magnet optimized for linac beam (Delta undulator) was developed at the Laboratory for Elementary-Particle Physics (LEPP) at Cornell University as part of insertion device development for the future Cornell 5 GeV Energy Recovery Source of coherent hard X-rays [1,7]. To evaluate mechanical, vacuum and magnetic properties of the magnet, a short 30 cm model with a 5 mm diameter round gap and a 2.4 cm period was built and tested in LEPP. The beam test of the Delta undulator model was conducted at Accelerator Test Facility (ATF) in BNL with ˜60 MeV linac beam. The beam testing results confirmed basic properties of the undulator magnet obtained through the magnetic field measurement. In the paper we describe the magnet design, techniques and setups used for the magnetic field measurement and the beam testing results.

  1. DOE Field Operations Program EV and HEV Testing

    SciTech Connect

    Francfort, James Edward; Slezak, L. A.

    2001-10-01

    The United States Department of Energy’s (DOE) Field Operations Program tests advanced technology vehicles (ATVs) and disseminates the testing results to provide fleet managers and other potential ATV users with accurate and unbiased information on vehicle performance. The ATVs (including electric, hybrid, and other alternative fuel vehicles) are tested using one or more methods - Baseline Performance Testing (EVAmerica and Pomona Loop), Accelerated Reliability Testing, and Fleet Testing. The Program (http://ev.inel.gov/sop) and its nine industry testing partners have tested over 30 full-size electric vehicle (EV) models and they have accumulated over 4 million miles of EV testing experience since 1994. In conjunction with several original equipment manufacturers, the Program has developed testing procedures for the new classes of hybrid, urban, and neighborhood EVs. The testing of these vehicles started during 2001. The EVS 18 presentation will include (1) EV and hybrid electric vehicle (HEV) test results, (2) operating experience with and performance trends of various EV and HEV models, and (3) experience with operating hydrogen-fueled vehicles. Data presented for EVs will include vehicle efficiency (km/kWh), average distance driven per charge, and range testing results. The HEV data will include operating considerations, fuel use rates, and range testing results.

  2. Automated microbial metabolism laboratory. [design of advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into test chambers

    NASA Technical Reports Server (NTRS)

    1974-01-01

    The design and rationale of an advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into each of four test chambers are outlined. The feasibility for multiple addition tests was established and various details of the methodology were studied. The four chamber battery of tests include: (1) determination of the effect of various atmospheric gases and selection of that gas which produces an optimum response; (2) determination of the effect of incubation temperature and selection of the optimum temperature for performing Martian biochemical tests; (3) sterile soil is dosed with a battery of C-14 labeled substrates and subjected to experimental temperature range; and (4) determination of the possible inhibitory effects of water on Martian organisms is performed initially by dosing with 0.01 ml and 0.5 ml of medium, respectively. A series of specifically labeled substrates are then added to obtain patterns in metabolic 14CO2 (C-14)O2 evolution.

  3. Antarctic field tests of SARSAT personal locater beacons

    NASA Technical Reports Server (NTRS)

    Bindschadler, Robert

    1987-01-01

    Field tests of SARSAT personal locater beacons were conducted in the Antarctic to assess the viability of using these beacons to increase the safety of Antarctic field parties. Data were collected on the extent to which dry or wet snow, melting conditions, crevasse walls and snow bridges affected the ability of the SARSAT satellite to calculate an accurate position of the beacon. Average response time between beacon turn on and alert reception in McMurdo was between 4 and 5 hours for these tests. It is concluded that the SARSAT system is viable for Antarctic operations and it is recommended that it be implemented for future field operations. Because of obstruction of line-of-sight between beacon and satellite degrades the accuracy of the location calculation (particularly in wet snow), it is further recommended that field parties have sufficient numbers of beacons to insure that in an emergency, one will be able to operate from the surface.

  4. Field tests of carbon monitoring methods in forestry projects

    SciTech Connect

    1999-07-01

    In response to the emerging scientific consensus on the facts of global climate change, the international Joint Implementation (JI) program provided a pilot phase in which utilities and other industries could finance, among other activities, international efforts to sequester carbon dioxide, a major greenhouse gas. To make JI and its successor mechanisms workable, however, cost-effective methods are needed for monitoring progress in the reduction of greenhouse gas emissions. The papers in this volume describe field test experiences with methods for measuring carbon storage by three types of land use: natural forest, plantation forest, and agroforestry. Each test, in a slightly different land-use situation, contributes to the knowledge of carbon-monitoring methods as experienced in the field. The field tests of the agroforestry guidelines in Guatemala and the Philippines, for example, suggested adaptations in terms of plot size and method of delineating the total area for sampling.

  5. Field testing of fugitive dust control techniques at a uranium mill tailings pile - 1982 Field Test, Gas Hills, Wyoming.

    SciTech Connect

    Elmore, M.R.; Hartley, J.N.

    1983-12-01

    A field test was conducted on a uranium tailings pile to evaluate the effectiveness of 15 chemical stabilizers for control of fugitive dust from uranium mill tailings. A tailings pile at the Federal American Partners (FAP) Uranium Mill, Gas Hills, Wyoming, was used for the field test. Preliminary laboratory tests using a wing tunnel were conducted to select the more promising stabilizers for field testing. Fourteen of the chemical stabilizers were applied with a field spray system pulled behind a tractor; one--Hydro Mulch--was applied with a hydroseeder. A portable weather station and data logger were installed to record the weather conditions at the test site. After 1 year of monitoring (including three site visits), all of the stabilizers have degraded to some degree; but those applied at the manufacturers' recommended rate are still somewhat effective in reducing fugitive emissions. The following synthetic polymer emulsions appear to be the more effective stabilizers: Wallpol 40-133 from Reichold Chemicals, SP-400 from Johnson and March Corporation, and CPB-12 from Wen Don Corporation. Installed costs for the test plots ranged from $8400 to $11,300/ha; this range results from differences in stabilizer costs. Large-scale stabilization costs of the test materials are expected to range from $680 to $3600/ha based on FAP experience. Evaluation of the chemical stabilizers will continue for approximately 1 year. 2 references, 33 figures, 22 tables.

  6. Vadose zone transport field study: Detailed test plan for simulated leak tests

    SciTech Connect

    AL Ward; GW Gee

    2000-06-23

    : identify mechanisms controlling transport processes in soils typical of the hydrogeologic conditions of Hanford's waste disposal sites; reduce uncertainty in conceptual models; develop a detailed and accurate database of hydraulic and transport parameters for validation of three-dimensional numerical models; identify and evaluate advanced, cost-effective characterization methods with the potential to assess changing conditions in the vadose zone, particularly as surrogates of currently undetectable high-risk contaminants. This plan provides details for conducting field tests during FY 2000 to accomplish these objectives. Details of additional testing during FY 2001 and FY 2002 will be developed as part of the work planning process implemented by the Integration Project.

  7. Mass spectra in N=1 SQCD with additional colorless but flavored fields

    NASA Astrophysics Data System (ADS)

    Chernyak, Victor L.

    2017-01-01

    Considered is the N=1 supersymmetric QCD-like Φ -theory with SU(N_c) colors and 0< N_F<2N_c flavors of light quarks Q^i_a,{overline{Q}}^{ a}_j with equal small masses. In addition to quarks and gluons of the standard N=1 SQCD, it includes N^2_F colorless but flavored fields Φ ij, with the large mass parameter μ _{Φ } ≫ Λ _Q (Λ _Q is the scale factor of the gauge coupling), interacting with quarks through the Yukawa coupling in the superpotential. The mass spectra of this (direct) Φ -theory are first directly calculated in all vacua with the unbroken or spontaneously broken flavor symmetry U(N_F)→ U(n_1)× U(n_2) at 0fields Φ `turn back' and there appear two additional generations of light Φ -particles with small masses μ ^pole(Φ )≪ Λ _Q. Also considered is the X-theory which is the N=2 SQCD with SU(N_c) colors and 0< N_F<2N_c flavors of light quarks, broken down to N=1 by the large mass

  8. Compositions, Functions, and Testing of Friction Brake Materials and Their Additives

    SciTech Connect

    Blau, PJ

    2001-10-22

    The purpose of this report is to present a survey of commercial brake materials and additives, and to indicate their typical properties and functions, especially as regards their use in heavy trucks. Most truck pad and shoe materials described here were designed to wear against cast iron. Brake material test methods are also briefly described. This report does not address issues associated with the fabrication and manufacturing of brake materials. Since there are literally thousands of brake material additives, and their combinations are nearly limitless, it is impractical to list them all here. Rather, an attempt has been made to capture the primary constituents and their functions. An Appendix contains thermo-physical properties of some current and potential brake materials.

  9. Design, Development and Hotfire Testing of Monolithic Copper and Bimetallic Additively Manufactured Combustion Chambers

    NASA Technical Reports Server (NTRS)

    Gradl, Paul; Barnett, Greg; Brandsmeier, Will; Greene, Sandy Elam; Protz, Chris

    2016-01-01

    NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM) otherwise commonly referred to as additive manufacturing. The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for the GRCop-84 copper-alloy commensurate with powder bed additive manufacturing, evaluate bimetallic deposition and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. As a direct spin off of this program, NASA is working with industry partners to further develop the printing process for the GRCop-84 material in addition to the C-18150 (CuCrZr) material. To advance the process further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic additively manufactured chambers. A 1.2k sized thrust-chamber was designed and developed to compare the printing process of the GRCop-84 and C-18150 SLM materials. A series of similar MCC liners also completed development with an Inconel 625 jacket bonded to the GRcop-84 liner evaluating direct metal deposition (DMD) laser and arc-based techniques. This paper describes the design, development, manufacturing and testing of these combustion chambers and associated lessons learned throughout the design and development process.

  10. Field test of fiber optic ocean bottom seismograph

    NASA Astrophysics Data System (ADS)

    Zhang, Wentao; Wang, Zhaogang; Huang, Wenzhu; Li, Li; Liu, Wenyi; Luo, Yingbo; Li, Fang

    2016-05-01

    In this paper we report the field test of fiber optic ocean bottom seismograph (OOBS) which can be used in the active source seismic research. There are three fiber laser accelerometers (FLAs) and one fiber laser hydrophone (FLH), which is wavelength division multiplexed, in the OOBS. The interrogation system is put on shore and is connected with the OOBS with optical fiber cable. The field test of using an air gun is carried out under water with a depth of 30 m. The results show that the OOBS has similar performance as conventional electric OBS.

  11. Event-related potential practice effects on the Paced Auditory Serial Addition Test (PASAT)

    PubMed Central

    Rogers, Jeffrey M.; Fox, Alison M.

    2012-01-01

    Practice can change the nature and quality of a stimulus-response relationship. The current study observed the effects of repeated administration of the Paced Auditory Serial Addition Test (PASAT) in 12 healthy individuals, in an effort to establish distinct profiles associated with novel and practiced processing. Over four training sessions the mean number of correct responses on this demanding test of attention significantly improved and was approaching ceiling for most task conditions. Behavioural improvements were associated with significantly reduced amplitude of late Processing Negativity, a frontally distributed component of the event-related potential waveform associated with voluntary, limited-capacity activity within higher-order attentional systems. These results suggest that PASAT performance became more efficient as practice seemingly eased the strategic planning and coordination requirements the task places on frontally-mediated executive attention resources. The findings of the current study extend our understanding of the functional and behavioural mechanisms underlying the effects of practice. PMID:23717344

  12. Application and testing of additive manufacturing for mirrors and precision structures

    NASA Astrophysics Data System (ADS)

    Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

    2015-09-01

    Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

  13. Field test of two energetic models for yellow perch

    USGS Publications Warehouse

    Schaeffer, J.S.; Haas, R.C.; Diana, J.S.; Breck, J.E.

    1999-01-01

    Field data from a population of yellow perch Perca flavescens in Saginaw Bay, Lake Huron, were used to evaluate the ability of two energetic models to predict consumption by yellow perch. Field estimates of daily ration for age-l-4 fish during May through October 1987 and 1988 were compared with independent predictions made by the Wisconsin energetic model and an energetic model developed by Karas and Thoresson. Predictions of daily ration using the Wisconsin model were lower than daily rations estimated from field data for all ages, primarily due to poor model-field agreement at temperatures above 22??C. This caused estimates of cumulative consumption from the Wisconsin model to be 25-50% lower than field estimates. Predictions of daily ration by the Karas-Thoresson model agreed with field estimates over a temperature range of 1026??C for age-1-3 yellow perch but not for older fish. Despite improvement, model predictions of cumulative consumption were 2-35% lower than field estimates. Although these tests of predicted and estimated rations may provide insight into which model produced more accurate results, it must be emphasized that field measures of daily ration are also estimates and may be in error, particularly at temperatures above 22??C where gastric evacuation rates were estimated. The Karas-Thoresson modification of the Wisconsin energetic model produced better fits to field ration data and is recommended for model applications.

  14. Field tests-low input, side-wall vented boiler

    SciTech Connect

    Litzke, W.L.; Butcher, T.A.; Celebi, Y.

    1996-07-01

    The Fan Atomized Burner (FAB) was developed at Brookhaven National Laboratory as part of the Oil Heat Combustion Equipment Technology Program to provide a practical low-firing rate technology leading to new, high efficiency oil-fired appliances. The development of the burner design and results of application testing have been presented in prior oil heat conferences over the past several years. This information is also summarized in a more comprehensive BNL report. The first field trial of a prototype unit was initiated during the 1994-95 heating season. This paper presents the results of the second year of testing, during the 1995-96 heating season. The field tests enable the demonstration of the reliability and performance of the FAB under practical, typical operating conditions. Another important objective of the field test was to demonstrate that the low input is adequate to satisfy the heating and hot water demands of the household. During the first field trial it was shown that at a maximum input rate of 0.4 gph (55,000 Btu/hr) the burner was able to heat a home with over 2,000 square feet of conditioned living space and provide adequate supply of domestic hot water for a family of six. The test is located in Long Island, NY.

  15. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    PubMed Central

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-01-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator. PMID:27509823

  16. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    NASA Astrophysics Data System (ADS)

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-08-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator.

  17. Field test of the Rapid Transuranic Monitoring Laboratory

    SciTech Connect

    McIsaac, C.V.; Sill, C.W.; Gehrke, R.J.; Killian, E.W.; Watts, K.D.; Amaro, C.R.

    1993-12-01

    A field test of the Rapid Transuranic Monitoring Laboratory (RTML) developed at the Idaho National Engineering Laboratory (INEL) was conducted as part of a demonstration sponsored by the Buried Waste Integrated Demonstration (BWID). The RTML is a mobile, field- deployable laboratory developed for use at buried radioactive waste remediation sites to allow onsite preparation and analysis of soil, smear, and air filter samples for alpha and gamma-emitting contaminants. Analytical instruments installed in the RTML include an extended range, germanium photon analysis spectrometer with an automatic sample changer, two large-area ionization chamber alpha spectrometers, and four alpha continuous air monitors. The performance of the RTML was tested at the Test Reactor Area and Cold Test Pit near the Radioactive Waste Management Complex at the INEL. Objectives, experimental procedures, and an evaluation of the performance of the RTML are presented.

  18. Size characterization by Sedimentation Field Flow Fractionation of silica particles used as food additives.

    PubMed

    Contado, Catia; Ravani, Laura; Passarella, Martina

    2013-07-25

    Four types of SiO2, available on the market as additives in food and personal care products, were size characterized using Sedimentation Field Flow Fractionation (SdFFF), SEM, TEM and Photon Correlation Spectroscopy (PCS). The synergic use of the different analytical techniques made it possible, for some samples, to confirm the presence of primary nanoparticles (10 nm) organized in clusters or aggregates of different dimension and, for others, to discover that the available information is incomplete, particularly that regarding the presence of small particles. A protocol to extract the silica particles from a simple food matrix was set up, enriching (0.25%, w w(-1)) a nearly silica-free instant barley coffee powder with a known SiO2 sample. The SdFFF technique, in conjunction with SEM observations, made it possible to identify the added SiO2 particles and verify the new particle size distribution. The SiO2 content of different powdered foodstuffs was determined by graphite furnace atomic absorption spectroscopy (GFAAS); the concentrations ranged between 0.006 and 0.35% (w w(-1)). The protocol to isolate the silica particles was so applied to the most SiO2-rich commercial products and the derived suspensions were separated by SdFFF; SEM and TEM observations supported the size analyses while GFAAS determinations on collected fractions permitted element identification.

  19. Sequential accelerated tests: Improving the correlation of accelerated tests to module performance in the field

    NASA Astrophysics Data System (ADS)

    Felder, Thomas; Gambogi, William; Stika, Katherine; Yu, Bao-Ling; Bradley, Alex; Hu, Hongjie; Garreau-Iles, Lucie; Trout, T. John

    2016-09-01

    DuPont has been working steadily to develop accelerated backsheet tests that correlate with solar panels observations in the field. This report updates efforts in sequential testing. Single exposure tests are more commonly used and can be completed more quickly, and certain tests provide helpful predictions of certain backsheet failure modes. DuPont recommendations for single exposure tests are based on 25-year exposure levels for UV and humidity/temperature, and form a good basis for sequential test development. We recommend a sequential exposure of damp heat followed by UV then repetitions of thermal cycling and UVA. This sequence preserves 25-year exposure levels for humidity/temperature and UV, and correlates well with a large body of field observations. Measurements can be taken at intervals in the test, although the full test runs 10 months. A second, shorter sequential test based on damp heat and thermal cycling tests mechanical durability and correlates with loss of mechanical properties seen in the field. Ongoing work is directed toward shorter sequential tests that preserve good correlation to field data.

  20. Decomposition of conifer tree bark under field conditions: effects of nitrogen and phosphorus additions

    NASA Astrophysics Data System (ADS)

    Lopes de Gerenyu, Valentin; Kurganova, Irina; Kapitsa, Ekaterina; Shorokhova, Ekaterina

    2016-04-01

    In forest ecosystems, the processes of decomposition of coarse woody debris (CWD) can contribute significantly to the emission component of carbon (C) cycle and thus accelerate the greenhouse effect and global climate change. A better understanding of decomposition of CWD is required to refine estimates of the C balance in forest ecosystems and improve biogeochemical models. These estimates will in turn contribute to assessing the role of forests in maintaining their long-term productivity and other ecosystems services. We examined the decomposition rate of coniferous bark with added nitrogen (N) and phosphorus (P) fertilizers in experiment under field conditions. The experiment was carried out in 2015 during 17 weeks in Moscow region (54o50'N, 37o36'E) under continental-temperate climatic conditions. The conifer tree bark mixture (ca. 70% of Norway spruce and 30% of Scots pine) was combined with soil and placed in piles of soil-bark substrate (SBS) with height of ca. 60 cm and surface area of ca. 3 m2. The dry mass ratio of bark to soil was 10:1. The experimental design included following treatments: (1) soil (Luvisols Haplic) without bark, (S), (2) pure SBS, (3) SBS with N addition in the amount of 1% of total dry bark mass (SBS-N), and (4) SBS with N and P addition in the amount of 1% of total dry bark mass for each element (SBS-NP). The decomposition rate expressed as CO2 emission flux, g C/m2/h was measured using closed chamber method 1-3 times per week from July to early November using LiCor 6400 (Nebraska, USA). During the experiment, we also controlled soil temperature at depths of 5, 20, 40, and 60 cm below surface of SBS using thermochrons iButton (DS1921G, USA). The pattern of CO2 emission rate from SBS depended strongly on fertilizing. The highest decomposition rates (DecR) of 2.8-5.6 g C/m2/h were observed in SBS-NP treatment during the first 6 weeks of experiment. The decay process of bark was less active in the treatment with only N addition. In this

  1. U.S. field testing programs and results

    SciTech Connect

    Wicks, G.G.

    2000-06-09

    The United States has been active in four major international in-situ or field testing programs over the past two decades, involving the burial of simulated high-level waste forms and package components. These programs are designed to supplement laboratory testing studies in order to obtain the most complete and realistic picture possible of waste glass behavior under realistic repository-relevant conditions.

  2. Seasonal variations of grounding parameters by field tests

    SciTech Connect

    Patel, S.G.

    1992-07-01

    The past fifteen years have seen considerable research in the area of substation grounding design, analysis and testing. These research include the revision of the IEEE Std.-80, the development of PC based computer programs, the in depth analysis of grounding parameters and the development of new field testing methods and devices. In spite of these advances, several questions were often asked, primarily due to safety concerns. The questions were related to the seasonal variation of critical grounding parameters such as the soil and gravel resistivities and their influence on the body current in an accidental circuit. There was also a need to study the total behavior of a substation ground grid with respect to different weather conditions by performing field tests. In response to the above needs, a comprehensive field test program was developed and implemented. The field test consisted of flowing approximately 150 amperes through the Texas Valley ground grid from a remote substation. The parameters investigated in this project were the grid impedance, the grid potential rise (GPR) , the fault current distribution, the touch/step voltages, the body current on different gravel beds and the soil/gravel resistivities. The measurements were performed in the rainy, winter and summer weather conditions during 1989--1990. The field test results, overall, indicate that the rainy weather is the worst condition for the substation safety because of the substantial reduction in the protective characteristics of the gravel. Among the gravel types, the washed gravel has much superior protective characteristics compared to the crusher run type of gravel. A comparison of SGSYS computed grounding parameters with measured results indicates that the grid resistance and GPR compare well but the computed touch voltage and body current are substantially higher than the measured values.

  3. Intermittent versus Continuous Incremental Field Tests: Are Maximal Variables Interchangeable?

    PubMed Central

    Carminatti, Lorival J.; Possamai, Carlos A. P.; de Moraes, Marcelo; da Silva, Juliano F.; de Lucas, Ricardo D.; Dittrich, Naiandra; Guglielmo, Luiz G. A.

    2013-01-01

    The aim of the present study was to compare physiological responses derived from an incremental progressive field test with a constant speed test i.e. intermittent versus continuous protocol. Two progressive maximum tests (Carminatti`s test (T-CAR) and the Vameval test (T-VAM)), characterized by increasing speed were used. T-CAR is an intermittent incremental test, performed as shuttle runs; while T-VAM is a continuous incremental test performed on an athletic track. Eighteen physically active, healthy young subjects (21.9 ± 2.0 years; 76.5 ± 8.6 kg, 1.78 ± 0.08 m, 11.2 ± 5.4% body fat), volunteered for this study. Subjects performed four different maximum test sessions conducted in the field: two incremental tests and two time to exhaustion tests (TTE) at peak test velocities (PV). No significant differences were found for PV (T-CAR = 15.6 ± 1.2; T-VAM = 15.5 ± 1.3 km·h-1) and maximal HR (T-CAR = 195 ± 11; T- VAM = 194 ± 14 bpm). During TTE, there were no significant differences for HR (TTET-CAR and TTET-VAM = 192 ± 12 bpm). However, there was a significant difference in TTE (p = 0.04) (TTET-CAR = 379 ± 84, TTET-VAM = 338 ± 58 s) with a low correlation (r = 0.41). The blood lactate concentration measured at the end of the TTE tests, showed no significant difference (TTET-CAR = 13.2 ± 2.4 vs. TTET-VAM = 12.9 ± 2.4 mmol·l-1). Based on the present findings, it is suggested that the maximal variables derived from T-CAR and T-VAM can be interchangeable in the design of training programs. Key points T-CAR is an intermittent shuttle run test that predicts the maximal aerobic speed with accuracy, hence, test results could be interchangeable with continuous straight-line tests. T-CAR provides valid field data for evaluating aerobic fitness. In comparison with T-VAM, T-CAR may be a more favourable way to prescribe intermittent training using a shuttle-running protocol. PMID:24149741

  4. Large-scale field testing on flexible shallow landslide barriers

    NASA Astrophysics Data System (ADS)

    Bugnion, Louis; Volkwein, Axel; Wendeler, Corinna; Roth, Andrea

    2010-05-01

    Open shallow landslides occur regularly in a wide range of natural terrains. Generally, they are difficult to predict and result in damages to properties and disruption of transportation systems. In order to improve the knowledge about the physical process itself and to develop new protection measures, large-scale field experiments were conducted in Veltheim, Switzerland. Material was released down a 30° inclined test slope into a flexible barrier. The flow as well as the impact into the barrier was monitored using various measurement techniques. Laser devices recording flow heights, a special force plate measuring normal and shear basal forces as well as load cells for impact pressures were installed along the test slope. In addition, load cells were built in the support and retaining cables of the barrier to provide data for detailed back-calculation of load distribution during impact. For the last test series an additional guiding wall in flow direction on both sides of the barrier was installed to achieve higher impact pressures in the middle of the barrier. With these guiding walls the flow is not able to spread out before hitting the barrier. A special constructed release mechanism simulating the sudden failure of the slope was designed such that about 50 m3 of mixed earth and gravel saturated with water can be released in an instant. Analysis of cable forces combined with impact pressures and velocity measurements during a test series allow us now to develop a load model for the barrier design. First numerical simulations with the software tool FARO, originally developed for rockfall barriers and afterwards calibrated for debris flow impacts, lead already to structural improvements on barrier design. Decisive for the barrier design is the first dynamic impact pressure depending on the flow velocity and afterwards the hydrostatic pressure of the complete retained material behind the barrier. Therefore volume estimation of open shallow landslides by assessing

  5. A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

    NASA Technical Reports Server (NTRS)

    Grady, Joseph E.; Haller, William J.; Poinsatte, Philip E.; Halbig, Michael C.; Schnulo, Sydney L.; Singh, Mrityunjay; Weir, Don; Wali, Natalie; Vinup, Michael; Jones, Michael G.; Patterson, Clark; Santelle, Tom; Mehl, Jeremy

    2015-01-01

    The research and development activities reported in this publication were carried out under NASA Aeronautics Research Institute (NARI) funded project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing." The objective of the project was to conduct evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. The results of the activities are described in three part report. The first part of the report contains the data and analysis of engine system trade studies, which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. The technical scope of activities included an assessment of the feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composites, which were accomplished by fabricating prototype engine components and testing them in simulated engine operating conditions. The manufacturing process parameters were developed and optimized for polymer and ceramic composites (described in detail in the second and third part of the report). A number of prototype components (inlet guide vane (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included turbine nozzle components. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

  6. The virtual fields method applied to spalling tests on concrete

    NASA Astrophysics Data System (ADS)

    Pierron, F.; Forquin, P.

    2012-08-01

    For one decade spalling techniques based on the use of a metallic Hopkinson bar put in contact with a concrete sample have been widely employed to characterize the dynamic tensile strength of concrete at strain-rates ranging from a few tens to two hundreds of s-1. However, the processing method mainly based on the use of the velocity profile measured on the rear free surface of the sample (Novikov formula) remains quite basic and an identification of the whole softening behaviour of the concrete is out of reach. In the present paper a new processing method is proposed based on the use of the Virtual Fields Method (VFM). First, a digital high speed camera is used to record the pictures of a grid glued on the specimen. Next, full-field measurements are used to obtain the axial displacement field at the surface of the specimen. Finally, a specific virtual field has been defined in the VFM equation to use the acceleration map as an alternative `load cell'. This method applied to three spalling tests allowed to identify Young's modulus during the test. It was shown that this modulus is constant during the initial compressive part of the test and decreases in the tensile part when micro-damage exists. It was also shown that in such a simple inertial test, it was possible to reconstruct average axial stress profiles using only the acceleration data. Then, it was possible to construct local stress-strain curves and derive a tensile strength value.

  7. A FIELD VALIDATION OF TWO SEDIMENT-AMPHIPOD TOXICITY TESTS

    EPA Science Inventory

    A field validation study of two sediment-amphipod toxicity tests was conducted using sediment samples collected subtidally in the vicinity of a polycyclic aromatic hydrocarbon (PAH)-contaminated Superfund site in Elliott Bay, WA, USA. Sediment samples were collected at 30 stati...

  8. Development and Field Tests of the Army Work Environment Questionnaire

    DTIC Science & Technology

    1987-05-01

    from the low teens to the mid-twenties), a number of consistent trends were found in the pattern of relationships. In both field tests, the largest...identifying impediments to productivity (UPRDC TR-81-18). San Diego, CA: Navy Personnel Research and Development Center. 39 Appendix A iiOONMwc IUCIDU PORN

  9. Field Testing Vocational Education Metric Modules. Final Report.

    ERIC Educational Resources Information Center

    Oldsen, Carl F.

    A project was conducted for the following purposes: (1) to develop a workshop training package to prepare vocational education teachers to use vocational subject-specific modules; (2) to train those teachers to use the workshop package; (3) to conduct field tests of the metric modules with experimental and control groups; (4) to analyze, describe,…

  10. A Field Test of the TIME Patient Simulation Model.

    ERIC Educational Resources Information Center

    Harless, William G.; And Others

    1990-01-01

    The Technological Innovations in Medical Education (TIME) model, designed to be controlled by a professor in the classroom, incorporates voice recognition technology and video dramatization to create a believable patient encounter. A field test finding was that the students became committed to the care and management of the simulated patient.…

  11. A Preliminary Field Test of an Employee Work Passion Model

    ERIC Educational Resources Information Center

    Zigarmi, Drea; Nimon, Kim; Houson, Dobie; Witt, David; Diehl, Jim

    2011-01-01

    Four dimensions of a process model for the formulation of employee work passion, derived from Zigarmi, Nimon, Houson, Witt, and Diehl (2009), were tested in a field setting. A total of 447 employees completed questionnaires that assessed the internal elements of the model in a corporate work environment. Data from the measurements of work affect,…

  12. Injury Prevention for the Elderly. Field Test Instructor Coursebook.

    ERIC Educational Resources Information Center

    Walker, Bonnie

    This coursebook is intended for use by the instructors presenting a workshop on preventing injuries in the elderly that was developed as a field test of a larger 10-module training program for staff of long-term health care facilities, senior center and adult day care staff, and home health aides. The curriculum guide served as a blueprint for the…

  13. 46 CFR 160.151-29 - Additional approval tests for SOLAS A and SOLAS B inflatable liferafts.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 6 2014-10-01 2014-10-01 false Additional approval tests for SOLAS A and SOLAS B... Inflatable Liferafts (SOLAS) § 160.151-29 Additional approval tests for SOLAS A and SOLAS B inflatable...), Chapter IV/4.3.5 (incorporated by reference, see § 160.151-5 of this subpart), the following test must...

  14. 46 CFR 160.151-29 - Additional approval tests for SOLAS A and SOLAS B inflatable liferafts.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 6 2013-10-01 2013-10-01 false Additional approval tests for SOLAS A and SOLAS B... Inflatable Liferafts (SOLAS) § 160.151-29 Additional approval tests for SOLAS A and SOLAS B inflatable...), Chapter IV/4.3.5 (incorporated by reference, see § 160.151-5 of this subpart), the following test must...

  15. Outcomes Assessment: An Examination of the ETS Major Field Test and the Comprehensive Business Exam

    ERIC Educational Resources Information Center

    Hahn, William; Bowlin, Lyle L.; Welch, Timothy

    2012-01-01

    This study is the first to examine student performance differences between the major field test in business (MFTB) and the comprehensive business exam (CBE). Results reveal students performed at a statistically significant 50.8 percentile ranking on the CBE compared to a 38.0 percentile ranking on the MFTB. Additionally, this study finds that…

  16. Sulfur-free lignins from alkaline pulping tested in mortar for use as mortar additives.

    PubMed

    Nadif, A; Hunkeler, D; Käuper, P

    2002-08-01

    Sulfur-free lignin, obtained through the acid precipitation of black liquor from the soda pulping process, has been tested as water reducer in mortar. It has also been compared to existing commercial additives such as naphthalene sulfonates and lignosulfonates. The ash content and sugar content of these lignins are low in comparison to lignosulfonates, conferring on them higher purity. A procedure for small scale testing derived from the industrial norms SN-EN196 and ASTM (Designation C230-90) is presented. Specifically, all the sulfur-free lignins tested improved the flow of the mortar. Selected flax lignins performed better than lignosulfonates though still less than naphthalene sulfonates. Furthermore, certain hemp lignins gave comparable results to the lignosulfonates. Overall, the straw lignin prepared herein is comparable in performance to commercially available lignins, such as Organocell, Alcell and Curan 100. The plant from which the lignin was isolated, and the process of the pulp mill are the primary influences on the performance of the lignin.

  17. Testing departure from additivity in Tukey's model using shrinkage: application to a longitudinal setting.

    PubMed

    Ko, Yi-An; Mukherjee, Bhramar; Smith, Jennifer A; Park, Sung Kyun; Kardia, Sharon L R; Allison, Matthew A; Vokonas, Pantel S; Chen, Jinbo; Diez-Roux, Ana V

    2014-12-20

    While there has been extensive research developing gene-environment interaction (GEI) methods in case-control studies, little attention has been given to sparse and efficient modeling of GEI in longitudinal studies. In a two-way table for GEI with rows and columns as categorical variables, a conventional saturated interaction model involves estimation of a specific parameter for each cell, with constraints ensuring identifiability. The estimates are unbiased but are potentially inefficient because the number of parameters to be estimated can grow quickly with increasing categories of row/column factors. On the other hand, Tukey's one-degree-of-freedom model for non-additivity treats the interaction term as a scaled product of row and column main effects. Because of the parsimonious form of interaction, the interaction estimate leads to enhanced efficiency, and the corresponding test could lead to increased power. Unfortunately, Tukey's model gives biased estimates and low power if the model is misspecified. When screening multiple GEIs where each genetic and environmental marker may exhibit a distinct interaction pattern, a robust estimator for interaction is important for GEI detection. We propose a shrinkage estimator for interaction effects that combines estimates from both Tukey's and saturated interaction models and use the corresponding Wald test for testing interaction in a longitudinal setting. The proposed estimator is robust to misspecification of interaction structure. We illustrate the proposed methods using two longitudinal studies-the Normative Aging Study and the Multi-ethnic Study of Atherosclerosis.

  18. Testing Departure from Additivity in Tukey’s Model using Shrinkage: Application to a Longitudinal Setting

    PubMed Central

    Ko, Yi-An; Mukherjee, Bhramar; Smith, Jennifer A.; Park, Sung Kyun; Kardia, Sharon L.R.; Allison, Matthew A.; Vokonas, Pantel S.; Chen, Jinbo; Diez-Roux, Ana V.

    2014-01-01

    While there has been extensive research developing gene-environment interaction (GEI) methods in case-control studies, little attention has been given to sparse and efficient modeling of GEI in longitudinal studies. In a two-way table for GEI with rows and columns as categorical variables, a conventional saturated interaction model involves estimation of a specific parameter for each cell, with constraints ensuring identifiability. The estimates are unbiased but are potentially inefficient because the number of parameters to be estimated can grow quickly with increasing categories of row/column factors. On the other hand, Tukey’s one degree of freedom (df) model for non-additivity treats the interaction term as a scaled product of row and column main effects. Due to the parsimonious form of interaction, the interaction estimate leads to enhanced efficiency and the corresponding test could lead to increased power. Unfortunately, Tukey’s model gives biased estimates and low power if the model is misspecified. When screening multiple GEIs where each genetic and environmental marker may exhibit a distinct interaction pattern, a robust estimator for interaction is important for GEI detection. We propose a shrinkage estimator for interaction effects that combines estimates from both Tukey’s and saturated interaction models and use the corresponding Wald test for testing interaction in a longitudinal setting. The proposed estimator is robust to misspecification of interaction structure. We illustrate the proposed methods using two longitudinal studies — the Normative Aging Study and the Multi-Ethnic Study of Atherosclerosis. PMID:25112650

  19. Deep Borehole Field Test Research Activities at LBNL

    SciTech Connect

    Dobson, Patrick; Tsang, Chin-Fu; Kneafsey, Timothy; Borglin, Sharon; Piceno, Yvette; Andersen, Gary; Nakagawa, Seiji; Nihei, Kurt; Rutqvist, Jonny; Doughty, Christine; Reagan, Matthew

    2016-08-19

    The goal of the U.S. Department of Energy Used Fuel Disposition’s (UFD) Deep Borehole Field Test is to drill two 5 km large-diameter boreholes: a characterization borehole with a bottom-hole diameter of 8.5 inches and a field test borehole with a bottom-hole diameter of 17 inches. These boreholes will be used to demonstrate the ability to drill such holes in crystalline rocks, effectively characterize the bedrock repository system using geophysical, geochemical, and hydrological techniques, and emplace and retrieve test waste packages. These studies will be used to test the deep borehole disposal concept, which requires a hydrologically isolated environment characterized by low permeability, stable fluid density, reducing fluid chemistry conditions, and an effective borehole seal. During FY16, Lawrence Berkeley National Laboratory scientists conducted a number of research studies to support the UFD Deep Borehole Field Test effort. This work included providing supporting data for the Los Alamos National Laboratory geologic framework model for the proposed deep borehole site, conducting an analog study using an extensive suite of geoscience data and samples from a deep (2.5 km) research borehole in Sweden, conducting laboratory experiments and coupled process modeling related to borehole seals, and developing a suite of potential techniques that could be applied to the characterization and monitoring of the deep borehole environment. The results of these studies are presented in this report.

  20. Observational testing of magnetospheric magnetic field models at geosynchronous orbit

    SciTech Connect

    Weiss, L.A.; Thomsen, M.F.; Reeves, G.D.; McComas, D.J.

    1996-09-01

    Empirical mode which estimate the magnetic field direction and magnitude at any point within the magnetosphere under a variety of conditions play an important role in space weather forecasting. We report here on a number of different studies aimed at quantitatively evaluating these models, and in particular the Tsyganenko T89a model. The models are evaluated in two basic ways: (1) by comparing the range of magnetic field tilt angles observed at geosynchronous orbit with the ranges predicted for the same locations by the models; and (2) by comparing the observed magnetic field mapping between the ionosphere and geosynchronous orbit (using two-satellite magnetic field conjunctions) with the model predictions at the same locations. We find that while the T89a model predicts reasonably well the basic variation in tilt angle with local time and permits a range of field inclinations adequate to encompass the majority of observed angles on the dawn, dusk, and night sides, it is unable to reproduce the range of inclinations on the dayside. The model also predicts a smaller magnetic latitude range of geosynchronous field line footpoints than the observed two-satellite mapping indicate. Together, these results suggest that the next generation of field models should allow a greater range of stretching, especially in local time sectors away from midnight. It is important to note, however, that any increased range should encompass less-stretched configurations: although there are certainly cases where the models are not sufficiently stretched, we find that on average all magnetic field models tested, including T89a, are too stretched. Finally, in investigating how well the observed degree of field stretch was ordered by various magnetospheric indices, we find that the tilt of the field at geosynchronous orbit is a promising candidate for the incorporation into future models.

  1. Field Testing of a Portable Radiation Detector and Mapping System

    SciTech Connect

    Hofstetter, K.J.; Hayes, D.W.; Eakle, R.F.

    1998-03-01

    Researchers at the Savannah River Site (SRS) have developed a man- portable radiation detector and mapping system (RADMAPS) which integrates the accumulation of radiation information with precise ground locations. RADMAPS provides field personnel with the ability to detect, locate, and characterize nuclear material at a site or facility by analyzing the gamma or neutron spectra and correlating them with position. the man-portable field unit records gamma or neutron count rate information and its location, along with date and time, using an embedded Global Positioning System (GPS). RADMAPS is an advancement in data fusion, integrating several off-the-shelf technologies with new computer software resulting in a system that is simple to deploy and provides information useful to field personnel in an easily understandable form. Decisions on subsequent actions can be made in the field to efficiently use available field resources. The technologies employed in this system include: recording GPS, radiation detection (typically scintillation detectors), pulse height analysis, analog-to-digital converters, removable solid-state (Flash or SRAM) memory cards, Geographic Information System (GIS) software and personal computers with CD-ROM supporting digital base maps. RADMAPS includes several field deployable data acquisition systems designed to simultaneously record radiation and geographic positions. This paper summarizes the capabilities of RADMAPS and some of the results of field tests performed with the system.

  2. 76 FR 31823 - Technical Amendment to List of User Fee Airports: Addition of Dallas Love Field Municipal Airport...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-02

    ... Airports: Addition of Dallas Love Field Municipal Airport, Dallas, TX AGENCY: U.S. Customs and Border... revising the list of user fee airports to reflect the recent user fee airport designation for Dallas Love... of user fee status for Dallas Love Field Municipal Airport. This document updates the list of...

  3. Laboratory or Field Tests for Evaluating Firefighters' Work Capacity?

    PubMed Central

    Lindberg, Ann-Sofie; Oksa, Juha; Malm, Christer

    2014-01-01

    Muscle strength is important for firefighters work capacity. Laboratory tests used for measurements of muscle strength, however, are complicated, expensive and time consuming. The aims of the present study were to investigate correlations between physical capacity within commonly occurring and physically demanding firefighting work tasks and both laboratory and field tests in full time (N = 8) and part-time (N = 10) male firefighters and civilian men (N = 8) and women (N = 12), and also to give recommendations as to which field tests might be useful for evaluating firefighters' physical work capacity. Laboratory tests of isokinetic maximal (IM) and endurance (IE) muscle power and dynamic balance, field tests including maximal and endurance muscle performance, and simulated firefighting work tasks were performed. Correlations with work capacity were analyzed with Spearman's rank correlation coefficient (rs). The highest significant (p<0.01) correlations with laboratory and field tests were for Cutting: IE trunk extension (rs = 0.72) and maximal hand grip strength (rs = 0.67), for Stairs: IE shoulder flexion (rs = −0.81) and barbell shoulder press (rs = −0.77), for Pulling: IE shoulder extension (rs = −0.82) and bench press (rs = −0.85), for Demolition: IE knee extension (rs = 0.75) and bench press (rs = 0.83), for Rescue: IE shoulder flexion (rs = −0.83) and bench press (rs = −0.82), and for the Terrain work task: IE trunk flexion (rs = −0.58) and upright barbell row (rs = −0.70). In conclusion, field tests may be used instead of laboratory tests. Maximal hand grip strength, bench press, chin ups, dips, upright barbell row, standing broad jump, and barbell shoulder press were strongly correlated (rs≥0.7) with work capacity and are therefore recommended for evaluating firefighters work capacity. PMID:24614596

  4. Large Field Photogrammetry Techniques in Aircraft and Spacecraft Impact Testing

    NASA Technical Reports Server (NTRS)

    Littell, Justin D.

    2010-01-01

    The Landing and Impact Research Facility (LandIR) at NASA Langley Research Center is a 240 ft. high A-frame structure which is used for full-scale crash testing of aircraft and rotorcraft vehicles. Because the LandIR provides a unique capability to introduce impact velocities in the forward and vertical directions, it is also serving as the facility for landing tests on full-scale and sub-scale Orion spacecraft mass simulators. Recently, a three-dimensional photogrammetry system was acquired to assist with the gathering of vehicle flight data before, throughout and after the impact. This data provides the basis for the post-test analysis and data reduction. Experimental setups for pendulum swing tests on vehicles having both forward and vertical velocities can extend to 50 x 50 x 50 foot cubes, while weather, vehicle geometry, and other constraints make each experimental setup unique to each test. This paper will discuss the specific calibration techniques for large fields of views, camera and lens selection, data processing, as well as best practice techniques learned from using the large field of view photogrammetry on a multitude of crash and landing test scenarios unique to the LandIR.

  5. 40 CFR 1065.935 - Emission test sequence for field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air flow. (2) If the standard-setting part requires hot-start emission measurements, shut down the...) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement... follows: (1) If the standard-setting part requires only hot-stabilized emission measurements, operate...

  6. Role of energy systems in two intermittent field tests in women field hockey players.

    PubMed

    Lemmink, Koen A P M; Visscher, Susan H

    2006-08-01

    The energetics of 2 field tests that reflect physical performance in intermittent sports (i.e., the Interval Shuttle Sprint Test [ISST] and the Interval Shuttle Run Test [ISRT]) were examined in 21 women field hockey players. The ISST required the players to perform 10 shuttle sprints starting every 20 seconds. During the ISRT, players alternately ran 20-m shuttles for 30 seconds and walked for 15 seconds with increasing speed. Anaerobic and aerobic power tests included Wingate cycle sprints and a .V(O2)max cycle test, respectively. Based on correlation and regression analyses, it was concluded that for the ISST, anaerobic energetic pathways contribute mainly to energy supply for peak sprint time, while aerobic energetic pathways also contribute to energy supply for total sprint time. Energy during the ISRT is supplied mainly by the aerobic energy system. Depending on the aspect of physical performance a coach wants to determine, the ISST or ISRT can be used.

  7. Overspinning BTZ black holes with test particles and fields

    NASA Astrophysics Data System (ADS)

    Düztaş, Koray

    2016-12-01

    It has been claimed that in a test of an asymptotically anti-de Sitter version of weak cosmic censorship conjecture by attempting to overspin a Bañados, Teitelboim, and Zanelli (BTZ) black hole with test particles, one finds that it is not possible to spin up the black hole past its extremal limit. The result of this analysis is restricted to the case where the initial black hole is extremal. We extend this analysis to find that massive test particles can overspin the black hole, if we start with a nearly extremal black hole, instead. We also consider the interaction of the BTZ black hole with test fields. We show that overspinning of nearly extremal black holes is possible whether or not there is super-radiance for the field. If there is super-radiance, overspinning occurs in a narrow range of frequencies bounded below by the super-radiant limit. However, if there is no super-radiance for the field, overspinning becomes generic and also applies to extremal black holes. This is in analogy with the Kerr case.

  8. ITER Test Blanket Module Error Field Simulation Experiments

    NASA Astrophysics Data System (ADS)

    Schaffer, M. J.

    2010-11-01

    Recent experiments at DIII-D used an active-coil mock-up to investigate effects of magnetic error fields similar to those expected from two ferromagnetic Test Blanket Modules (TBMs) in one ITER equatorial port. The largest and most prevalent observed effect was plasma toroidal rotation slowing across the entire radial profile, up to 60% in H-mode when the mock-up local ripple at the plasma was ˜4 times the local ripple expected in front of ITER TBMs. Analysis showed the slowing to be consistent with non-resonant braking by the mock-up field. There was no evidence of strong electromagnetic braking by resonant harmonics. These results are consistent with the near absence of resonant helical harmonics in the TBM field. Global particle and energy confinement in H-mode decreased by <20% for the maximum mock-up ripple, but <5% at the local ripple expected in ITER. These confinement reductions may be linked with the large velocity reductions. TBM field effects were small in L-mode but increased with plasma beta. The L-H power threshold was unaffected within error bars. The mock-up field increased plasma sensitivity to mode locking by a known n=1 test field (n = toroidal harmonic number). In H-mode the increased locking sensitivity was from TBM torque slowing plasma rotation. At low beta, locked mode tolerance was fully recovered by re-optimizing the conventional DIII-D ``I-coils'' empirical compensation of n=1 errors in the presence of the TBM mock-up field. Empirical error compensation in H-mode should be addressed in future experiments. Global loss of injected neutral beam fast ions was within error bars, but 1 MeV fusion triton loss may have increased. The many DIII-D mock-up results provide important benchmarks for models needed to predict effects of TBMs in ITER.

  9. Pilot scale cooling tower fouled fill treatment: AFCATT (Anti-Fouling Chemical Additive Test Tower)

    SciTech Connect

    Newton, M.T.; Noble, R.T.; Philpot, E.F.; Eastis, J.H.

    1995-02-01

    Polyvinylchloride (PVC) film-type cellular fill is the fill of choice in replacing cement asbestor board fill in existing cooling towers and in new cooling towers because of its high thermal performance, ease of installation, and low initial cost. However, PVC fill has been found to foul quickly with biological and sediment material, significant reducing tower performance and the fill`s useful life. The Anti-Fouling Chemical Additives Test Tower (AFCATT) has been built to study accumulation rates of fouling deposits in corrugated PVC film fill and to study methods of cleaning and preventing the fouling deposits. This small mechanical draft cooling tower is located next to the Unit 4 natural draft cooling tower at Georgia Power Company`s Plant Bowen. The once-through mechanical draft tower receives hot water from the condenser and returns the cold water to the basin of the host tower. The pilot tower is divided into four chambers allowing for three different treatment programs and one control to be run simultaneously. PVC fill packs are suspended from load cells to allow the weight of the fill packs to be measured continuously. Six vendors participated in the summer 1993 test program. Each proposed different methods of cleaning the fouled fill and were given the opportunity to try their proposed method of fill cleaning. The success of each treatment program was determined by its ability to reduce fill pack weight (i.e., reduce fouling).

  10. Evaluation of the JP-8+100 additive candidates in the extended duration thermal stability test system

    SciTech Connect

    Binns, K.E.; Dieterle, G.L.

    1996-10-01

    The most promising JP-8+100 additive candidates consists of dispersants, detergents, antioxidants and metal deactivators. A series of tests were conducted in the Extended Duration Thermal Stability Test System to determine the thermal stability effects of the individual JP-8+100 additives and combinations of the additives. This paper will cover the test results and their relationship to future aircraft fuel systems. The Extended Duration Thermal Stability Test System was designed to conduct long duration tests at non-accelerated temperature conditions and resident times representative or aircraft/engine fuel systems. This system and its operating characteristics will also be covered in this paper.

  11. The biobehavioral family model: testing social support as an additional exogenous variable.

    PubMed

    Woods, Sarah B; Priest, Jacob B; Roush, Tara

    2014-12-01

    This study tests the inclusion of social support as a distinct exogenous variable in the Biobehavioral Family Model (BBFM). The BBFM is a biopsychosocial approach to health that proposes that biobehavioral reactivity (anxiety and depression) mediates the relationship between family emotional climate and disease activity. Data for this study included married, English-speaking adult participants (n = 1,321; 55% female; M age = 45.2 years) from the National Comorbidity Survey Replication, a nationally representative epidemiological study of the frequency of mental disorders in the United States. Participants reported their demographics, marital functioning, social support from friends and relatives, anxiety and depression (biobehavioral reactivity), number of chronic health conditions, and number of prescription medications. Confirmatory factor analyses supported the items used in the measures of negative marital interactions, social support, and biobehavioral reactivity, as well as the use of negative marital interactions, friends' social support, and relatives' social support as distinct factors in the model. Structural equation modeling indicated a good fit of the data to the hypothesized model (χ(2)  = 846.04, p = .000, SRMR = .039, CFI = .924, TLI = .914, RMSEA = .043). Negative marital interactions predicted biobehavioral reactivity (β = .38, p < .001), as did relatives' social support, inversely (β = -.16, p < .001). Biobehavioral reactivity predicted disease activity (β = .40, p < .001) and was demonstrated to be a significant mediator through tests of indirect effects. Findings are consistent with previous tests of the BBFM with adult samples, and suggest the important addition of family social support as a predicting factor in the model.

  12. SMART wind turbine rotor. Design and field test

    SciTech Connect

    Berg, Jonathan Charles; Resor, Brian Ray; Paquette, Joshua A.; White, Jonathan Randall

    2014-01-01

    The Wind Energy Technologies department at Sandia National Laboratories has developed and field tested a wind turbine rotor with integrated trailing-edge flaps designed for active control of rotor aerodynamics. The SMART Rotor project was funded by the Wind and Water Power Technologies Office of the U.S. Department of Energy (DOE) and was conducted to demonstrate active rotor control and evaluate simulation tools available for active control research. This report documents the design, fabrication, and testing of the SMART Rotor. This report begins with an overview of active control research at Sandia and the objectives of this project. The SMART blade, based on the DOE / SNL 9-meter CX-100 blade design, is then documented including all modifications necessary to integrate the trailing edge flaps, sensors incorporated into the system, and the fabrication processes that were utilized. Finally the test site and test campaign are described.

  13. Field Testing: Independent, Accredited Testing and Validation for the Wind Industry (Fact Sheet)

    SciTech Connect

    Not Available

    2011-11-01

    This fact sheet describes the field testing capabilities at the National Wind Technology Center (NWTC). NREL's specialized facilities and personnel at the NWTC provide the U.S. wind industry with scientific and engineering support that has proven critical to the development of wind energy for U.S. energy needs. The NWTC's specialized field-testing capabilities have evolved over 30 years of continuous support by the U.S. Department of Energy Wind and Hydropower Technologies Program and long standing industry partnerships. The NWTC provides wind industry manufacturers, developers, and operators with turbine and component testing all in one convenient location. Although industry utilizes sophisticated modeling tools to design and optimize turbine configurations, there are always limitations in modeling capabilities, and testing is a necessity to ensure performance and reliability. Designs require validation and testing is the only way to determine if there are flaws. Prototype testing is especially important in capturing manufacturing flaws that might require fleet-wide retrofits. The NWTC works with its industry partners to verify the performance and reliability of wind turbines that range in size from 400 Watts to 3 megawatts. Engineers conduct tests on components and full-scale turbines in laboratory environments and in the field. Test data produced from these tests can be used to validate turbine design codes and simulations that further advance turbine designs.

  14. Scientific investigation plan for initial engineered barrier system field tests

    SciTech Connect

    Wunan Lin

    1993-02-01

    The purpose of this Scientific Investigation Plan (SIP) is to describe tests known as Initial Engineered Barrier System Field Tests (IEBSFT) and identified by Work Breakdown Structure as WBS 1.2.2.2.4. The IEBSFT are precursors to the Engineered Barrier System Field Test (EBSFT), WBS 1.2.2.2.4, to be conducted in the Exploratory Study Facility (ESF) at Yucca Mountain. The EBSFT and IEBSFT are designed to provide information on the interaction between waste packages (simulated by heated containers) and the surrounding rock mass, its vadose water, and infiltrated water. Heater assemblies will be installed in drifts or boreholes openings and heated to measure moisture movement during heat-up and subsequent cool-down of the rock mass. In some of the tests, infiltration of water into the heated rock mass will be studied. Throughout the heating and cooling cycle, instruments installed in the rock will monitor such parameters as temperature, moisture content, concentration of some chemical species, and stress and strain. Rock permeability measurements, rock and fluid (water and gas) sampling, and fracture pattern measurements will also be made before and after the test.

  15. Field test of the bulk-assay calorimeter

    SciTech Connect

    Perry, R.B.; Keddar, A.

    1982-10-01

    The Bulk-Assay Calorimeter described in ANL-NDA-9/ISPO-14 was field tested at the Belgonucleaire mixed-oxide fuel fabrication plant at Dessel, Belgium, May 13-19, 1982. This instrument was developed under ISPO Tasks A-9 and A-47 at Argonne National Laboratory and was supplied to the IAEA through the U.S support program. Five containers of plutonium-oxide feed stock used in the manufacture of mixed-oxide LMFBR-type fuel were assayed during the test. Electrical measurements to verify the calibration of the calorimeter were also made.

  16. Resonant-test-field model of fluctuating nonlinear waves

    NASA Astrophysics Data System (ADS)

    West, Bruce J.

    1982-03-01

    A Hamiltonian system of nonlinear dispersive waves is used as a basis for generalizing the test-wave model to a set of resonantly interacting waves. The resonant test field (RTF) is shown to obey a nonlinear generalized Langevin equation in general. In the Markov limit a Fokker-Planck equation is obtained and the exact steady-state solution is determined. An algebraic expression for the power spectral density is obtained in terms of the number of resonantly interacting waves (n) in the RTF, the interaction strength (Vk), and the dimensionality of the wave field (d). For gravity waves on the ocean surface a k-4 spectrum is obtained, and for capillary waves a k-8 spectrum, both of which are in essential agreement with data.

  17. Field test of wake steering at an offshore wind farm

    DOE PAGES

    Fleming, Paul; Annoni, Jennifer; Shah, Jigar J.; ...

    2017-02-06

    In this study, a field test of wake steering control is presented. The field test is the result of a collaboration between the National Renewable Energy Laboratory (NREL) and Envision Energy, a smart energy management company and turbine manufacturer. In the campaign, an array of turbines within an operating commercial offshore wind farm in China have the normal yaw controller modified to implement wake steering according to a yaw control strategy. The strategy was designed using NREL wind farm models, including a computational fluid dynamics model, SOWFA, for understanding wake dynamics and an engineering model, FLORIS, for yaw control optimization.more » Results indicate that, within the certainty afforded by the data, the wake-steering controller was successful in increasing power capture, by amounts similar to those predicted from the models.« less

  18. Mathematical model of testing of pipeline integrity by thermal fields

    SciTech Connect

    Vaganova, Nataliia

    2014-11-18

    Thermal fields testing at the ground surface above a pipeline are considered. One method to obtain and investigate an ideal thermal field in different environments is a direct numerical simulation of heat transfer processes taking into account the most important physical factors. In the paper a mathematical model of heat propagation from an underground source is described with accounting of physical factors such as filtration of water in soil and solar radiation. Thermal processes are considered in 3D origin where the heat source is a pipeline with constant temperature and non-uniform isolated shell (with 'damages'). This problem leads to solution of heat diffusivity equation with nonlinear boundary conditions. Approaches to analysis of thermal fields are considered to detect damages.

  19. North Field 󈨛 Rapid Runway Repair Test Report. Volume 1.

    DTIC Science & Technology

    1988-11-01

    the grass, south of the repair site. Paint, polymer, and solvent, as well as storage drums for paint and polymer wastes, were stored in a designated ...events began. Fire and crash rescue support was provided by North Auxiliary Field. A "hot brakes" area was designated at the intersection of the NE/SW...upheaval and sag limits for each repair. Computer simulations, using the results of a runway survey and a test limit of 80 percent design limit load for

  20. Lidar Tracking of Multiple Fluorescent Tracers: Method and Field Test

    NASA Technical Reports Server (NTRS)

    Eberhard, Wynn L.; Willis, Ron J.

    1992-01-01

    Past research and applications have demonstrated the advantages and usefulness of lidar detection of a single fluorescent tracer to track air motions. Earlier researchers performed an analytical study that showed good potential for lidar discrimination and tracking of two or three different fluorescent tracers at the same time. The present paper summarizes the multiple fluorescent tracer method, discusses its expected advantages and problems, and describes our field test of this new technique.

  1. Incorporating Spatial Models in Visual Field Test Procedures

    PubMed Central

    Rubinstein, Nikki J.; McKendrick, Allison M.; Turpin, Andrew

    2016-01-01

    Purpose To introduce a perimetric algorithm (Spatially Weighted Likelihoods in Zippy Estimation by Sequential Testing [ZEST] [SWeLZ]) that uses spatial information on every presentation to alter visual field (VF) estimates, to reduce test times without affecting output precision and accuracy. Methods SWeLZ is a maximum likelihood Bayesian procedure, which updates probability mass functions at VF locations using a spatial model. Spatial models were created from empirical data, computational models, nearest neighbor, random relationships, and interconnecting all locations. SWeLZ was compared to an implementation of the ZEST algorithm for perimetry using computer simulations on 163 glaucomatous and 233 normal VFs (Humphrey Field Analyzer 24-2). Output measures included number of presentations and visual sensitivity estimates. Results There was no significant difference in accuracy or precision of SWeLZ for the different spatial models relative to ZEST, either when collated across whole fields or when split by input sensitivity. Inspection of VF maps showed that SWeLZ was able to detect localized VF loss. SWeLZ was faster than ZEST for normal VFs: median number of presentations reduced by 20% to 38%. The number of presentations was equivalent for SWeLZ and ZEST when simulated on glaucomatous VFs. Conclusions SWeLZ has the potential to reduce VF test times in people with normal VFs, without detriment to output precision and accuracy in glaucomatous VFs. Translational Relevance SWeLZ is a novel perimetric algorithm. Simulations show that SWeLZ can reduce the number of test presentations for people with normal VFs. Since many patients have normal fields, this has the potential for significant time savings in clinical settings. PMID:26981329

  2. On-site cell field test support program

    NASA Astrophysics Data System (ADS)

    Staniunas, J. W.; Merten, G. P.

    1982-09-01

    Utility sites for data monitoring were reviewed and selected. Each of these sites will be instrumented and its energy requirements monitored and analyzed for one year prior to the selection of 40 Kilowatt fuel cell field test sites. Analyses in support of the selection of sites for instrumentation shows that many building sectors offered considerable market potential. These sectors include nursing home, health club, restaurant, industrial, hotel/motel and apartment.

  3. Performance evaluation of infrared imaging system in field test

    NASA Astrophysics Data System (ADS)

    Wang, Chensheng; Guo, Xiaodong; Ren, Tingting; Zhang, Zhi-jie

    2014-11-01

    Infrared imaging system has been applied widely in both military and civilian fields. Since the infrared imager has various types and different parameters, for system manufacturers and customers, there is great demand for evaluating the performance of IR imaging systems with a standard tool or platform. Since the first generation IR imager was developed, the standard method to assess the performance has been the MRTD or related improved methods which are not perfect adaptable for current linear scanning imager or 2D staring imager based on FPA detector. For this problem, this paper describes an evaluation method based on the triangular orientation discrimination metric which is considered as the effective and emerging method to evaluate the synthesis performance of EO system. To realize the evaluation in field test, an experiment instrument is developed. And considering the importance of operational environment, the field test is carried in practical atmospheric environment. The test imagers include panoramic imaging system and staring imaging systems with different optics and detectors parameters (both cooled and uncooled). After showing the instrument and experiment setup, the experiment results are shown. The target range performance is analyzed and discussed. In data analysis part, the article gives the range prediction values obtained from TOD method, MRTD method and practical experiment, and shows the analysis and results discussion. The experimental results prove the effectiveness of this evaluation tool, and it can be taken as a platform to give the uniform performance prediction reference.

  4. Field-testing UV disinfection of drinking water

    SciTech Connect

    Gadgil, A.; Drescher, A.; Greene, D.; Miller, P.; Motau, C.; Stevens, F.

    1997-09-01

    A recently invented device, ``UV Waterworks,`` uses ultraviolet (UV) light to disinfect drinking water. Its novel features are: low cost, robust design, rapid disinfection, low electricity use, low maintenance, high flow rate and ability to work with unpressurized water sources. The device could service a community of 1,000 persons, at an annual total cost of less than 10 US cents per person. UV Waterworks has been successfully tested in the laboratory. Limited field trials of an early version of the device were conducted in India in 1994--95. Insights from these trials led to the present design. Extended field trials of UV Waterworks, initiated in South Africa in February 1997, will be coordinated by the South African Center for Essential Community Services (SACECS), with technical and organizational support from Lawrence Berkeley National Laboratory(LBNL) and the Natural Resources Defense Council (both US). The first of the eight planned sites of the year long trial is an AIDS hospice near Durban. Durban metro Water and LBNL lab-tested a UV Waterworks unit prior to installing it at the hospice in August, 1997. The authors describe the field test plans and preliminary results from Durban.

  5. Lessons Learned From Field Tests Of Planetary Surface Rovers

    NASA Astrophysics Data System (ADS)

    Stoker, C. R.

    2003-04-01

    I review results and lessons learned from field tests of planetary surface rovers. Terrestrial field tests help to train scientists in rover capabilities, and guides developments to improve them. Key metrics of rover science performance include distance traveled and number of science targets studied using instrument placement or sample manipulation. Field tests show that traverse range is governed primarily by commanding frequency rather than a rover’s maximum speed. With real-time feedback, teleoperated rovers can traverse kilometers per day. With commanded operations, typical traverses are a few meters. Longer traverses are risky and error prone. Tasks requiring moving a few meters to a target followed by manipulation or instrument placement take several command cycles per target. Higher level autonomy for navigation and manipulation is needed to improve performance. Rovers are being called upon to play a key role in the search for evidence of life on Mars. Conditions on the Martian surface today appear to preclude living organisms, but more clement conditions in the past may have supported the formation of a fossil record. However, any fossil record on Mars is likely to be produced by microbial life, and to be extremely ancient. Finding unambiguous evidence of biogenic origin of putative fossil structures will require collecting high priority samples and returning them to Earth. Recognition of fossiliferous deposits using rover data is problematical. Information provided by a rover is of very low bandwidth and fidelity compared to that observed by a field geologist. Limitations arise in both quality and quantity of data transmitted to Earth. In a rover mission simulation performed in a fossil-rich terrestrial field site hosting dinosaur tracks and stromatolites, science teams did not find any evidence of fossils. However, living organisms such as endolithic microorganisms and lichens have been identified in field experiments using color imaging and

  6. Simple and rapid field tests for brucellosis in livestock.

    PubMed

    Abdoel, Theresia; Dias, Isabel Travassos; Cardoso, Regina; Smits, Henk L

    2008-08-25

    Four simple and rapid field tests for the serodiagnosis of brucellosis in cattle, goat, sheep and swine were developed. The performance of the assays was investigated using serum samples collected in Portugal from animals originating from herds with a defined sanitary status with respect to the presence of brucellosis. The sensitivity calculated for the bovine, caprine, ovine and swine Brucella lateral flow assays based on results obtained for samples collected from animals with culture confirmed brucellosis was 90%, 100%, 90% and 73%, respectively. None of the samples from animals from herds free of brucellosis reacted in the flow assays indicating a high specificity. However, as expected, some degree of reactivity was observed when testing selected serum samples that reacted non-specific in reference tests for brucellosis.

  7. Evaluation of laser ultrasonic testing for inspection of metal additive manufacturing

    NASA Astrophysics Data System (ADS)

    Everton, Sarah; Dickens, Phill; Tuck, Chris; Dutton, Ben

    2015-03-01

    Additive Manufacturing (AM) offers a number of benefits over conventional processes. However, in order for these benefits to be realised, further development and integration of suitable monitoring and closed loop control systems are needed. Laser Ultrasonic Testing (LUT) is an inspection technology which shows potential for in-situ monitoring of metallic AM processes. Non-contact measurements can be performed on curved surfaces and in difficult to reach areas, even at elevated temperatures. Interrogation of each build layer generates defect information which can be used to highlight processing errors and allow for real-time modification of processing parameters, enabling improved component quality and yield. This study evaluates the use of laser-generated surface waves to detect artificially generated defects in titanium alloy (Ti- 6Al-4V) samples produced by laser-based Powder Bed Fusion. The trials undertaken utilise the latest LUT equipment, recently installed at Manufacturing Technology Centre which is capable of being controlled remotely. This will allow the system to optimise or adapt "on-the-fly", simplifying the eventual integration of the system within an AM machine.

  8. Field assessments in conjunction with whole effluent toxicity testing

    SciTech Connect

    La Point, T.W.; Waller, W.T.

    2000-01-01

    Whole effluent toxicity (WET) tests are widely used to assess potential effects of wastewater discharges on aquatic life. This paper represents a summary of chapters in a 1996 Society of Environmental Toxicology and Chemistry-sponsored workshop and a literature review concerning linkages between WET testing and associated field biomonitoring. Most published studies thus far focus primarily on benthic macroinvertebrates and on effluent-dominated stream systems in which effluents demonstrate little or no significant acute toxicity. Fewer studies examine WET test predictability in other aquatic ecosystems (e.g., wetlands, estuaries, large rivers) or deal with instream biota such as fish and primary producers. Published results indicate that standards for the usual WET freshwater test species, Ceriodaphnia dubia and Pimephales promelas, may not always protect most of the species inhabiting a receiving stream. Although WET tests are useful in predicting aquatic individual responses, they are not meant to directly measure natural population or community responses. Further, they do not address bioconcentration or bioaccumulation of hydrophobic compounds; do not assess eutrophication effects in receiving systems; and lastly, do not reflect genotoxic effects or function to test for endocrine-disrupting chemicals. Consequently, a more direct evaluation of ecosystem health, using bioassessment techniques, may be needed to properly evaluate aquatic systems affected by wastewater discharges.

  9. Geological Characterization of Remote Field Sites Using Visible and Infrared Spectroscopy: Results from the 1999 Marsokhod Field Test

    NASA Technical Reports Server (NTRS)

    Johnson, J. R.; Ruff, S. W.; Moersch, J.; Roush, T.; Horton, K.; Bishop, J.; Cabrol, N. A.; Cockell, C.; Gazis, P.; Newsom, H. E.

    2000-01-01

    The 1999 Marsokhod Field Experiment (MFE) provided an opportunity to test the suitability of rover-borne visible/near-infrared and thermal infrared field spectrometers to contribute to the remote geological exploration of a Mars analog field site.

  10. Statistical Tests of Taylor's Hypothesis: An Application to Precipitation Fields

    NASA Astrophysics Data System (ADS)

    Murthi, A.; Li, B.; Bowman, K.; North, G.; Genton, M.; Sherman, M.

    2009-05-01

    The Taylor Hypothesis (TH) as applied to rainfall is a proposition about the space-time covariance structure of the rainfall field. Specifically, it supposes that if a spatio-temporal precipitation field with a stationary covariance Cov(r, τ) in both space r and time τ, moves with a constant velocity v, then the temporal covariance at time lag τ is equal to the spatial covariance at space lag v τ, that is, Cov(0, τ) = Cov(v τ, 0). Qualitatively this means that the field evolves slowly in time relative to the advective time scale, which is often referred to as the 'frozen field' hypothesis. Of specific interest is whether there is a cut-off or decorrelation time scale for which the TH holds for a given mean flow velocity v. In this study the validity of the TH is tested for precipitation fields using high-resolution gridded NEXRAD radar reflectivity data produced by the WSI Corporation by employing two different statistical approaches. The first method is based upon rigorous hypothesis testing while the second is based on a simple correlation analysis, which neglects possible dependencies in the correlation estimates. We use radar reflectivity values from the southeastern United States with an approximate horizontal resolution of 4 km x 4 km and a temporal resolution of 15 minutes. During the 4-day period from 2 to 5 May 2002, substantial precipitation occurs in the region of interest, and the motion of the precipitation systems is approximately uniform. The results of both statistical methods suggest that the TH might hold for the shortest space and time scales resolved by the data (4 km and 15 minutes), but that it does not hold for longer periods or larger spatial scales. Also, the simple correlation analysis tends to overestimate the statistical significance through failing to account for correlations between the covariance estimates.

  11. Review and evaluation of literature on testing of chemical additives for scale control in geothermal fluids. Final report

    SciTech Connect

    Crane, C.H.; Kenkeremath, D.C.

    1981-01-01

    A selected group of reported tests of chemical additives in actual geothermal fluids are reviewed and evaluated to summarize the status of chemical scale-control testing and identify information and testing needs. The task distinguishes between scale control in the cooling system of a flash plant and elsewhere in the utilization system due to the essentially different operating environments involved. Additives for non-cooling geothermal fluids are discussed by scale type: silica, carbonate, and sulfide.

  12. Sensitization to Food Additives in Patients with Allergy: A Study Based on Skin Test and Open Oral Challenge.

    PubMed

    Moghtaderi, Mozhgan; Hejrati, Zinatosadat; Dehghani, Zahra; Dehghani, Faranak; Kolahi, Niloofar

    2016-06-01

    There has been a great increase in the consumption of various food additives in recent years. The purpose of this study was to identify the incidence of sensitization to food additives by using skin prick test in patients with allergy and to determine the concordance rate between positive skin tests and oral challenge in hypersensitivity to additives. This cross-sectional study included 125 (female 71, male 54) patients aged 2-76 years with allergy and 100 healthy individuals. Skin tests were performed in both patient and control groups with 25 fresh food additives. Among patients with allergy, 22.4% showed positive skin test at least to one of the applied materials. Skin test was negative to all tested food additives in control group. Oral food challenge was done in 28 patients with positive skin test, in whom 9 patients showed reaction to culprit (Concordance rate=32.1%). The present study suggested that about one-third of allergic patients with positive reaction to food additives showed positive oral challenge; it may be considered the potential utility of skin test to identify the role of food additives in patients with allergy.

  13. Government regulation and public opposition create high additional costs for field trials with GM crops in Switzerland.

    PubMed

    Bernauer, Thomas; Tribaldos, Theresa; Luginbühl, Carolin; Winzeler, Michael

    2011-12-01

    Field trials with GM crops are not only plant science experiments. They are also social experiments concerning the implications of government imposed regulatory constraints and public opposition for scientific activity. We assess these implications by estimating additional costs due to government regulation and public opposition in a recent set of field trials in Switzerland. We find that for every Euro spent on research, an additional 78 cents were spent on security, an additional 31 cents on biosafety, and an additional 17 cents on government regulatory supervision. Hence the total additional spending due to government regulation and public opposition was around 1.26 Euros for every Euro spent on the research per se. These estimates are conservative; they do not include additional costs that are hard to monetize (e.g. stakeholder information and dialogue activities, involvement of various government agencies). We conclude that further field experiments with GM crops in Switzerland are unlikely unless protected sites are set up to reduce these additional costs.

  14. Field tests of 2- and 40-tube condensers at the East Mesa Geothermal Test Site

    SciTech Connect

    Murphy, R.W.; Domingo, N.

    1982-05-01

    Two water-cooled isobutane condensers, one with 2 tubes and one with 40 tubes, were subjected to field tests at the East Mesa Geothermal Test Site to assess relative heat transfer performance in both surface evaporator and direct-contact evaporator modes. The five groups of tests established that field performance was below earlier laboratory-determined levels and that direct-contact evaporator mode performance was poorer than that for the surface evaporator mode. In all test situations, fluted condenser tubes performed better than smooth condenser tubes. Cooling water quality had no significant effect on performance, but brine preflash in the direct-contact mode did promote some relative performance improvement. Important implications of these results for binary geothermal power plants are that (1) working-fluid-side impurities can significantly degrade heat transfer performance of the power plant condensers and (2) provisions for minimizing such impurities may be required.

  15. Relation of field independence and test-item format to student performance on written piagetian tests

    NASA Astrophysics Data System (ADS)

    Ló; Pez-Rupérez, F.; Palacios, C.; Sanchez, J.

    In this study we have investigated the relationship between the field-dependence-independence (FDI) dimension as measured by the Group Embedded Figures Test (GEFT) and subject performance on the Longeot test, a pencil-and-paper Piagetian test, through the open or closed format of its items. The sample consisted of 141 high school students. Correlation and variance analysis show that the FDI dimension and GEFT correlate significantly on only those items on the Longeot test that require formal reasoning. The effect of open- or closed-item format is found exclusively for formal items; only the open format discriminates significantly (at the 0.01 level) between the field-dependent and -independent subjects performing on this type of item. Some implications of these results for science education are discussed.

  16. High temperature superconducting axial field magnetic coupler: realization and test

    NASA Astrophysics Data System (ADS)

    Belguerras, L.; Mezani, S.; Lubin, T.; Lévêque, J.; Rezzoug, A.

    2015-09-01

    Contactless torque transmission through a large airgap is required in some industrial applications in which hermetic isolation is necessary. This torque transmission usually uses magnetic couplers, whose dimension strongly depends on the airgap flux density. The use of high temperature superconducting (HTS) coils to create a strong magnetic field may constitute a solution to reduce the size of the coupler. It is also possible to use this coupler to replace a torque tube in transmitting the torque produced by a HTS motor to its load. This paper presents the detailed construction and tests of an axial field HTS magnetic coupler. Pancake coils have been manufactured from BSCCO tape and used in one rotor of the coupler. The second rotor is mainly composed of NdFeB permanent magnets. Several tests have been carried out showing that the constructed coupler is working properly. A 3D finite element (FE) model of the studied coupler has been developed. Airgap magnetic field and torque measurements have been carried out and compared to the FE results. It has been shown that the measured and the computed quantities are in satisfactory agreement.

  17. Environmental assessment of the 40 kilowatt fuel cell system field test operation

    NASA Technical Reports Server (NTRS)

    Bollenbacher, G.

    1982-01-01

    This environmental assessment examines the potential environmental consequences, both adverse and beneficial, of the 40 kW fuel cell system system field test operation. The assessment is of necessity generic in nature since actual test sites were not selected. This assessment provides the basis for determining the need for an environmental impact statement. In addition, this assessment provides siting criteria to avoid or minimize negative environmental impacts and standards for determining candidate test sites, if any, for which site specific assessments may be required.

  18. The Synthesis of Structural Responses Using Experimentally Measured Frequency Response Functions and Field Test Data

    SciTech Connect

    CAP,JEROME S.; NELSON,CURTIS F.

    2000-11-17

    This paper presents an analysis technique used to generate the structural response at locations not measured during the ejection of a captive-carried store. The ejection shock event is complicated by the fact that forces may be imparted to the store at eight distinct locations. The technique derives forcing functions by combining the initial field test data for a limited number of measurement locations with Frequency Response Functions (FRFs) measured using a traditional modal-type impact (tap) test at the same locations. The derived forcing functions were then used with tap test FRFs measured at additional locations of interest to produce the desired response data.

  19. Validity of Selected Lab and Field Tests of Physical Working Capacity.

    ERIC Educational Resources Information Center

    Burke, Edmund J.

    The validity of selected lab and field tests of physical working capacity was investigated. Forty-four male college students were administered a series of lab and field tests of physical working capacity. Lab tests include a test of maximum oxygen uptake, the PWC 170 test, the Harvard Step Test, the Progressive Pulse Ratio Test, Margaria Test of…

  20. Analysis of field test data on residential heating and cooling

    NASA Astrophysics Data System (ADS)

    Talbert, S. G.

    1980-12-01

    The computer program using field site data collected on 48 homes located in six cities in different climatic regions of the United States is discussed. In addition, a User's Guide was prepared for the computer program which is contained in a separate two-volume document entitled User's Guide for REAP: Residential Energy Analysis Program. Feasibility studies were conducted pertaining to potential improvements for REAP, including: the addition of an oil-furnace model; improving the infiltration subroutine; adding active and/or passive solar subroutines; incorporating a thermal energy storage model; and providing dual HVAC systems (e.g., heat pump-gas furnace). The purpose of REAP is to enable building designers and energy analysts to evaluate how such factors as building design, weather conditions, internal heat loads, and HVAC equipment performance, influence the energy requirements of residential buildings.

  1. Test plan and technical protocol for a field treatability test for bioventing

    SciTech Connect

    Hinchee, R.E.; Ong, S.K.; Miller, R.N.; Downey, D.C.; Frandt, R.

    1992-05-01

    Bioventing is an extremely cost-effective method for treating soils contaminated with fuels (JP-4, diesel, gasoline, and heating oil) and non-chlorinated solvents. In April of this year, the Air Force Center for Environmental Excellence (AFCEE) launched a nation-wide bioventing initiative to test the effectiveness of this innovative process at 55 contaminated sites in nineteen states. Twenty systems have already been installed and tested. To ensure that systems were installed and tested consistently, AFCEE developed the comprehensive protocol document. With minimal site specific modifications, the protocol is also used as a regulatory test plan. The concept significantly reduces test plan preparation costs. The AFCEE document introduces the bioventing technology and describes the technical procedures used to set up a bioventing system for field evaluation. It also provides testing, equipment, measurements, and other relevant quantitative data.

  2. Site Guidelines for a Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Sassani, D.; Kuhlman, K. L.; Freeze, G. A.; MacKinnon, R. J.; Perry, F.

    2015-12-01

    The US DOE Office of Nuclear Energy Used Nuclear Fuel Disposition Campaign (UFDC) is initiating a Deep Borehole Field Test (DBFT), without use of any radioactive waste, to evaluate the geoscience of the approach and technical capabilities for implementation. DOE has identified Sandia National Laboratories (SNL) as the Technical Lead for the UFDC DBFT Project, with the role of supporting DOE in (i) developing the overall DBFT Project Plan, (ii) management and integration of all DBFT Project activities, and (iii) providing Project technical guidance to DOE, other DOE National Laboratories, and university partners. The DBFT includes drilling one Characterization Borehole (CB-8.5" diameter), followed by an optional Field Test Borehole (FTB), to a depth of about 5,000 m (16,400 feet) into crystalline basement rock in a geologically stable continental location. The DBFT CB will be drilled and completed to facilitate downhole scientific testing and analyses. If site conditions are found to be favorable, DOE may drill the larger-diameter (17") FTB to facilitate proof-of-concept of handling, emplacement, and retrieval activities using surrogate waste containers. Guidelines for favorable DBFT site geohydrochemical and geomechanical conditions will be discussed and status of the DBFT Project will be provided. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2015-6426A.

  3. Geotechnical field measurements: G-tunnel, Nevada test site

    NASA Astrophysics Data System (ADS)

    Zimmerman, R. M.; Vollendorf, W. C.

    1982-05-01

    The FY81 geotechnical measurements focused on borehole measurements in the Grouse Canyon welded tuff in G-tunnel on the Nevada Test Site. These ambient temperature measures were taken to: (1) establish baseline reference field data, and (2) gain field testing experience in welded tuff. The in situ state of stress was obtained using the three-hole overcoring method with the US Bureau of Mines three-component borehole deformation gage. The orthogonal horizontal stresses were 5.5 and 0.3 MPa and the nominal vertical was 8.5. Biaxial tests were performed on recovered cores and the average modulus of deformation was 31 GPa. The modulus of deformation using the borehole jack (Goodman) had an average value of 12 GPa. This value is not corrected for effective bearing contact area. Two orthogonal boreholes were used to determine the range of hydraulic conductivities. The range was from 0.022 cm/s (22 Darcy's) to 1.923 cm/s (1988 Dracy's).

  4. Geotechnical field measurements: G-tunnel, Nevada Test Site

    SciTech Connect

    Zimmerman, R.M.; Vollendorf, W.C.

    1982-05-01

    The FY81 geotechnical measurements focused on borehole measurements in the Grouse Canyon welded tuff in G-tunnel on the Nevada Test Site. These ambient temperature measurements were taken to: (1) establish baseline reference field data, and (2) gain field testing experience in welded tuff. The in situ state of stress was obtained using the three-hole overcoring method with the US Bureau of Mines three-component borehole deformation gage. The orthogonal horizontal stresses were 5.5 and 0.3 MPa and the nominal vertical was 8.5. Biaxial tests were performed on recovered cores and the average modulus of deformation was 31 GPa. The modulus of deformation using the borehole jack (Goodman) had an average value of 12 GPa. This value is not corrected for effective bearing contact area. Two orthogonal boreholes were used to determine the range of hydraulic conductivities. The range was from 0.022 cm/s (22 Darcy`s) to 1.923 cm/s (1988 Darcy`s).

  5. Test plan for FY-94 digface characterization field experiments

    SciTech Connect

    Josten, N.E.; Roybal, L.G.

    1994-08-01

    The digface characterization concept has been under development at the Idaho National Engineering Laboratory (INEL) since fiscal year (FY) 1992 through the support of the Buried Waste Integrated Demonstration Program. A digface characterization system conducts continuous subsurface characterization simultaneously with retrieval of hazardous and radioactive waste from buried waste sites. The system deploys multiple sensors at the retrieval operation digface and collects data that provide a basis for detecting, locating, and classifying buried materials and hazardous conditions before they are disturbed by the retrieval equipment. This test plan describes ongoing efforts to test the digface characterization concept at the INEL`s Cold Test Pit using a simplified prototype deployment apparatus and off-the-shelf sensors. FY-94 field experiments will explore problems in object detection and classification. Detection and classification of objects are fundamental to three of the four primary functions of digface characterization during overburden removal. This test plan establishes procedures for collecting and validating the digface characterization data sets. Analysis of these data will focus on testing and further developing analysis methods for object detection and classification during overburden removal.

  6. Efficient field testing for load rating railroad bridges

    NASA Astrophysics Data System (ADS)

    Schulz, Jeffrey L.; Brett C., Commander

    1995-06-01

    As the condition of our infrastructure continues to deteriorate, and the loads carried by our bridges continue to increase, an ever growing number of railroad and highway bridges require load limits. With safety and transportation costs at both ends of the spectrum. the need for accurate load rating is paramount. This paper describes a method that has been developed for efficient load testing and evaluation of short- and medium-span bridges. Through the use of a specially-designed structural testing system and efficient load test procedures, a typical bridge can be instrumented and tested at 64 points in less than one working day and with minimum impact on rail traffic. Various techniques are available to evaluate structural properties and obtain a realistic model. With field data, a simple finite element model is 'calibrated' and its accuracy is verified. Appropriate design and rating loads are applied to the resulting model and stress predictions are made. This technique has been performed on numerous structures to address specific problems and to provide accurate load ratings. The merits and limitations of this approach are discussed in the context of actual examples of both rail and highway bridges that were tested and evaluated.

  7. Flow-Field Survey in the Test Region of the SR-71 Aircraft Test Bed Configuration

    NASA Technical Reports Server (NTRS)

    Mizukami, Masashi; Jones, Daniel; Weinstock, Vladimir D.

    2000-01-01

    A flat plate and faired pod have been mounted on a NASA SR-71A aircraft for use as a supersonic flight experiment test bed. A test article can be placed on the flat plate; the pod can contain supporting systems. A series of test flights has been conducted to validate this test bed configuration. Flight speeds to a maximum of Mach 3.0 have been attained. Steady-state sideslip maneuvers to a maximum of 2 deg have been conducted, and the flow field in the test region has been surveyed. Two total-pressure rakes, each with two flow-angle probes, have been placed in the expected vicinity of an experiment. Static-pressure measurements have been made on the flat plate. At subsonic and low supersonic speeds with no sideslip, the flow in the surveyed region is quite uniform. During sideslip maneuvers, localized flow distortions impinge on the test region. Aircraft sideslip does not produce a uniform sidewash over the test region. At speeds faster than Mach 1.5, variable-pressure distortions were observed in the test region. Boundary-layer thickness on the flat plate at the rake was less than 2.1 in. For future experiments, a more focused and detailed flow-field survey than this one would be desirable.

  8. Detailed field test of yaw-based wake steering

    SciTech Connect

    Fleming, Paul; Churchfield, Matt; Scholbrock, Andrew; Clifton, Andrew; Schreck, Scott; Johnson, Kathryn; Wright, Alan; Gebraad, Pieter; Annoni, Jennifer; Naughton, Brian; Berg, Jon; Herges, Tommy; White, Jon; Mikkelsen, Torben; Sjoholm, Mikael; Angelou, Nicolas

    2016-10-03

    This study describes a detailed field-test campaign to investigate yaw-based wake steering. In yaw-based wake steering, an upstream turbine intentionally misaligns its yaw with respect to the inflow to deflect its wake away from a downstream turbine, with the goal of increasing total power production. In the first phase, a nacelle-mounted scanning lidar was used to verify wake deflection of a misaligned turbine and calibrate wake deflection models. In the second phase, these models were used within a yaw controller to achieve a desired wake deflection. This paper details the experimental design and setup. Lastly, all data collected as part of this field experiment will be archived and made available to the public via the U.S. Department of Energy's Atmosphere to Electrons Data Archive and Portal.

  9. Detailed field test of yaw-based wake steering

    NASA Astrophysics Data System (ADS)

    Fleming, P.; Churchfield, M.; Scholbrock, A.; Clifton, A.; Schreck, S.; Johnson, K.; Wright, A.; Gebraad, P.; Annoni, J.; Naughton, B.; Berg, J.; Herges, T.; White, J.; Mikkelsen, T.; Sjöholm, M.; Angelou, N.

    2016-09-01

    This paper describes a detailed field-test campaign to investigate yaw-based wake steering. In yaw-based wake steering, an upstream turbine intentionally misaligns its yaw with respect to the inflow to deflect its wake away from a downstream turbine, with the goal of increasing total power production. In the first phase, a nacelle-mounted scanning lidar was used to verify wake deflection of a misaligned turbine and calibrate wake deflection models. In the second phase, these models were used within a yaw controller to achieve a desired wake deflection. This paper details the experimental design and setup. All data collected as part of this field experiment will be archived and made available to the public via the U.S. Department of Energy's Atmosphere to Electrons Data Archive and Portal.

  10. Detailed field test of yaw-based wake steering

    DOE PAGES

    Fleming, Paul; Churchfield, Matt; Scholbrock, Andrew; ...

    2016-10-03

    This study describes a detailed field-test campaign to investigate yaw-based wake steering. In yaw-based wake steering, an upstream turbine intentionally misaligns its yaw with respect to the inflow to deflect its wake away from a downstream turbine, with the goal of increasing total power production. In the first phase, a nacelle-mounted scanning lidar was used to verify wake deflection of a misaligned turbine and calibrate wake deflection models. In the second phase, these models were used within a yaw controller to achieve a desired wake deflection. This paper details the experimental design and setup. Lastly, all data collected as partmore » of this field experiment will be archived and made available to the public via the U.S. Department of Energy's Atmosphere to Electrons Data Archive and Portal.« less

  11. Additional field verification of convective scaling for the lateral dispersion parameter

    SciTech Connect

    Sakiyama, S.K.; Davis, P.A.

    1988-07-01

    The results of a series of diffusion trials over the heterogeneous surface of the Canadian Precambrian Shield provide additional support for the convective scaling of the lateral dispersion parameter. The data indicate that under convective conditions, the lateral dispersion parameter can be scaled with the convective velocity scale and the mixing depth. 10 references.

  12. Modeling of a Parabolic Trough Solar Field for Acceptance Testing: A Case Study

    SciTech Connect

    Wagner, M. J.; Mehos, M. S.; Kearney, D. W.; McMahan, A. C.

    2011-01-01

    As deployment of parabolic trough concentrating solar power (CSP) systems ramps up, the need for reliable and robust performance acceptance test guidelines for the solar field is also amplified. Project owners and/or EPC contractors often require extensive solar field performance testing as part of the plant commissioning process in order to ensure that actual solar field performance satisfies both technical specifications and performance guaranties between the involved parties. Performance test code work is currently underway at the National Renewable Energy Laboratory (NREL) in collaboration with the SolarPACES Task-I activity, and within the ASME PTC-52 committee. One important aspect of acceptance testing is the selection of a robust technology performance model. NREL1 has developed a detailed parabolic trough performance model within the SAM software tool. This model is capable of predicting solar field, sub-system, and component performance. It has further been modified for this work to support calculation at subhourly time steps. This paper presents the methodology and results of a case study comparing actual performance data for a parabolic trough solar field to the predicted results using the modified SAM trough model. Due to data limitations, the methodology is applied to a single collector loop, though it applies to larger subfields and entire solar fields. Special consideration is provided for the model formulation, improvements to the model formulation based on comparison with the collected data, and uncertainty associated with the measured data. Additionally, this paper identifies modeling considerations that are of particular importance in the solar field acceptance testing process and uses the model to provide preliminary recommendations regarding acceptable steady-state testing conditions at the single-loop level.

  13. Field Test: Results from the One Year Mission

    NASA Technical Reports Server (NTRS)

    Reschke, M. F.; Kozlovskaya, I. B.; Kofman, I. S.; Tomilovskaya, E. S.; Cerisano, J. M.; Rosenberg, M. J. F.; Bloomberg, J. J.; Stenger, M. B.; Lee, S. M. C.; Laurie, S. S.; Rukavishnikov, I. V.; Fomina, E. V.; Wood, S. J.; Mulavara, A. P.; Feiveson, A. H.; Fisher, E. A.; Phillips, T.; Ribeiro, C.; Taylor, L. C.; Miller, C. A.; Gadd, N. E.; Peters, B. T.; Kitov, V. V.; Lysova, N. Yu; Holden, K. L.; De Dios, Y.

    2017-01-01

    The One Year Mission was designed to aid in determining the effect that extending the duration on orbit aboard the International Space Station (ISS) would have on a number of biological and physiological systems. Two crewmembers were selected to participate in this endeavor, one U.S. On-Orbit Segment (USOS) astronaut and one Russian cosmonaut. The Neuroscience and Cardiovascular and Vision Laboratories at the Johnson Space Center and the Sensory-Motor and Countermeasures Division within the Institute for Biomedical Problems were selected to investigate vestibular, sensorimotor and cardiovascular function with the two long-duration crewmembers using the established methodology developed for the Field Test (FT).

  14. Field Testing of Utility Robots for Lunar Surface Operations

    NASA Technical Reports Server (NTRS)

    Fong, Terrence; Bualat, Maria; Deans, Matt; Allan, Mark; Bouyssounouse, Xavier; Broxton, Michael; Edwards, Laurence; Lee, Pascal; Lee, Susan Y.; Lees, David; Park, Eric; Pedersen, Liam; Smith, Trey; To, Vinh; Utz, Hans; Pacis, Estrellina; Schreckenghost, Debra

    2008-01-01

    Since 2004, NASA has been working to return to the Moon. In contrast to the Apollo missions, two key objectives of the current exploration program is to establish significant infrastructure and an outpost. Achieving these objectives will enable long-duration stays and long-distance exploration of the Moon. To do this, robotic systems will be needed to perform tasks which cannot, or should not, be performed by crew alone. In this paper, we summarize our work to develop "utility robots" for lunar surface operations, present results and lessons learned from field testing, and discuss directions for future research.

  15. Operation and design of selected industrial process heat field tests

    SciTech Connect

    Kearney, D. W.

    1981-02-01

    The DOE program of solar industrial process heat field tests has shown solar energy to be compatible with numerous industrial needs. Both the operational projects and the detailed designs of systems that are not yet operational have resulted in valuable insights into design and hardware practice. Typical of these insights are the experiences discussed for the four projects reviewed. Future solar IPH systems should benefit greatly not only from the availability of present information, but also from the wealth of operating experience from projects due to start up in 1981.

  16. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations.... You may use drilling fluids to conduct subsequent tests of a subsea BOP system; (c) Alternate tests... sizes of pipe in use, excluding drill collars and bottom-hole tools; (g) Pressure test affected...

  17. 46 CFR 160.035-12 - Additional preapproval tests required for F.R.P. lifeboats.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... and final measurements taken. There shall be no fractures or other signs of excessive stress and no... fractures or other signs of excessive stress and no appreciable set as a result of this test. (3) Swing test... span. The thwarts shall not fracture or otherwise be rendered unserviceable. (6) Towing test. With...

  18. Development and field testing of an adaptive power factor controller

    SciTech Connect

    El-Sharkawi, M.; Venkata, S.S.; Butler, N.G.; Yinger, R.W.

    1987-12-01

    The Adaptive Power Factor Controller (APFC) is a device that switches capacitors electronically to achieve almost unity power factor at the point of installation. It was designed and developed at the University of Washington (UW), and is being tested at the R and D facility of the Southern California Edison Company (SCE). It is particularly intended for loads with dynamically varying reactive power demands such as induction generators in wind power stations, or cyclically changing loads such as induction motors in process industries. It is also ideally suited for improving the power factor profile of a distribution line. The purposes of this paper are two-fold: to explain the most recent design of the 50-kVAR APFC and to report the results of the field testing program on the device after it was installed at the terminals of a 50-kW three-phase induction generator located at the Dever Wind R and D site of SCE.

  19. Thiopeptin, a New Feed-Additive Antibiotic: Biological Studies and Field Trials

    PubMed Central

    Mine, K.; Miyairi, N.; Takano, N.; Mori, S.; Watanabe, N.

    1972-01-01

    Thiopeptin is a new antibiotic, produced by Streptomyces tateyamensis and developed solely for animal use as a feed additive. The antibiotic content in animal tissue and feed was assayed in terms of the antimicrobial activity against Mycoplasma laidlawii A. This antibiotic was found to be relatively nontoxic in rats and mice. In chickens, this antibiotic is excreted into feces within 48 hr of administration and is not absorbed in tissue. It is well tolerated in both broilers and swine and is highly stable in animal feed. Thiopeptin-supplemented feed contributes to the improvement of weight gain, feed efficiency in chickens and swine, and the egg performance in layers. Thus, thiopeptin, when used as a feed additive, is quite suitable for supplementing animal nutrition. PMID:4680812

  20. An Approach to the Classification of Potential Reserve Additions of Giant Oil Fields of the World

    USGS Publications Warehouse

    Klett, T.R.; Tennyson, M.E.

    2008-01-01

    This report contains slides and notes for slides for a presentation given to the Committee on Sustainable Energy and the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology on 17 October 2007 in Geneva, Switzerland. The presentation describes the U.S. Geological Survey study to characterize and quantify petroleum-reserve additions, and the application of this study to help classify the quantities.

  1. Field Method for Detection of Metal Deactivator Additive in Jet Fuel

    DTIC Science & Technology

    2009-04-01

    sulphonic acid on the silica support. The SCX stationary phase is a silica gel with propylbenzenesulfonyl groups bound to the silica, Figure 6. S O O O...They can be grouped into three main categories based on the property of the additive they are detecting. The categories are the; a. Dispersant...was less prominent when lower concentrations of MDA were used. The elution properties of the copper and nickel MDA complexes was examined in a range

  2. The influence of polyvinylacetate additive in water on turbulent velocity field and drag reduction

    NASA Astrophysics Data System (ADS)

    Lodes, A.; Macho, V.

    1989-06-01

    The effect of polymer concentration on drag reduction was studied experimentally with diluted water solutions of polyvinylacetate in a 2.4 cm I. D. pipe. The instantaneous local velocities of the velocity fields were measured by a one-channel differential laser-Doppler anemometer DISA Mark II, with forward scattering. Concentrations of water-polyvinylacetate over the range from 10 to 2,000 ppm were used. The drag reduction coefficient is proportional to the concentration and hydrolysis degree of the saponificated polyvinylacetate (PVAC) employed. A mechanical degradation in the turbulent shear flow was not observed.

  3. Synergistic interactions between commonly used food additives in a developmental neurotoxicity test.

    PubMed

    Lau, Karen; McLean, W Graham; Williams, Dominic P; Howard, C Vyvyan

    2006-03-01

    Exposure to non-nutritional food additives during the critical development window has been implicated in the induction and severity of behavioral disorders such as attention deficit hyperactivity disorder (ADHD). Although the use of single food additives at their regulated concentrations is believed to be relatively safe in terms of neuronal development, their combined effects remain unclear. We therefore examined the neurotoxic effects of four common food additives in combinations of two (Brilliant Blue and L-glutamic acid, Quinoline Yellow and aspartame) to assess potential interactions. Mouse NB2a neuroblastoma cells were induced to differentiate and grow neurites in the presence of additives. After 24 h, cells were fixed and stained and neurite length measured by light microscopy with computerized image analysis. Neurotoxicity was measured as an inhibition of neurite outgrowth. Two independent models were used to analyze combination effects: effect additivity and dose additivity. Significant synergy was observed between combinations of Brilliant Blue with L-glutamic acid, and Quinoline Yellow with aspartame, in both models. Involvement of N-methyl-D-aspartate (NMDA) receptors in food additive-induced neurite inhibition was assessed with a NMDA antagonist, CNS-1102. L-glutamic acid- and aspartame-induced neurotoxicity was reduced in the presence of CNS-1102; however, the antagonist did not prevent food color-induced neurotoxicity. Theoretical exposure to additives was calculated based on analysis of content in foodstuff, and estimated percentage absorption from the gut. Inhibition of neurite outgrowth was found at concentrations of additives theoretically achievable in plasma by ingestion of a typical snack and drink. In addition, Trypan Blue dye exclusion was used to evaluate the cellular toxicity of food additives on cell viability of NB2a cells; both combinations had a straightforward additive effect on cytotoxicity. These data have implications for the

  4. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 34 Education 2 2010-07-01 2010-07-01 false What are the additional considerations for selecting Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF SPECIAL EDUCATION AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION DISABILITY...

  5. 34 CFR 350.55 - What are the additional considerations for selecting Field-Initiated Project applications for...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Field-Initiated Project applications for funding? 350.55 Section 350.55 Education Regulations of the..., DEPARTMENT OF EDUCATION DISABILITY AND REHABILITATION RESEARCH PROJECTS AND CENTERS PROGRAM How Does the Secretary Make an Award? § 350.55 What are the additional considerations for selecting...

  6. Use of laboratory and field testing to identify potential production problems in the Troll field

    SciTech Connect

    Hartley, R.; Jadid, M.B.

    1989-02-01

    The areal extent of the oil found in Troll made it clear at a very early stage in the field's appraisal that subsea wells would be required if the oil were developed. Owing to cooling in the subsea flowline, subsea wells can be expected to pose more production chemistry problems than would be expected with conventional platform wells. Consequently, a number of laboratory tests were carried out during the appraisal campaign to identify problems to be expected with scaling, foaming, emulsification, wax deposition, and hydrates. Dehydration and wax deposition tests were also carried out offshore during appraisal-well testing. These tests are described, together with the methods subsequently adopted to minimize future production problems.

  7. Field exercise testing for assessing fitness in French standardbred trotters.

    PubMed

    Couroucé, A

    1999-03-01

    This review considers standardized exercise testing which is, routinely used for French Trotters in the field. Track testing provides a more limited range of measurements than treadmill testing, but has the advantage of being performed in the horse's natural environment. Various measurements such as heart rate during exercise and blood lactate concentration after exercise may be measured on the track and lead to the calculation of physiological variables such as V200 (velocity corresponding to a 200 bpm heart rate) and V4 (velocity corresponding to a 4 mmol/L blood lactate concentration). V4 is related to the onset of blood lactate accumulation and relates to the aerobic capacity of the horse, as horses with high values for V4 have higher aerobic capacities. Although V4 is calculated during submaximal intensity exercise, it is related to racing performance and seems to be the most important measurement to assess changes in fitness. V200 represents the cardiac capacity of the horse during exercise and is close to V4 in mature horses. To explain further the clinical usefulness of track testing, and to help interpret both V4 and V200 variables, examples of exercise tests in 3-year-old French Trotters are presented here. These results show that changes may occur in V4 and V200 according to different factors such as the horse's physical ability and either training or disease states. It underlines the importance of exercise tests for both trainers and veterinarians and how they may help in the evaluation of a horse's performance ability; in defining the intensity of a training program, and also in the early detection of underlying diseases.

  8. Comprehensive visual field test & diagnosis system in support of astronaut health and performance

    NASA Astrophysics Data System (ADS)

    Fink, Wolfgang; Clark, Jonathan B.; Reisman, Garrett E.; Tarbell, Mark A.

    Long duration spaceflight, permanent human presence on the Moon, and future human missions to Mars will require autonomous medical care to address both expected and unexpected risks. An integrated non-invasive visual field test & diagnosis system is presented for the identification, characterization, and automated classification of visual field defects caused by the spaceflight environment. This system will support the onboard medical provider and astronauts on space missions with an innovative, non-invasive, accurate, sensitive, and fast visual field test. It includes a database for examination data, and a software package for automated visual field analysis and diagnosis. The system will be used to detect and diagnose conditions affecting the visual field, while in space and on Earth, permitting the timely application of therapeutic countermeasures before astronaut health or performance are impaired. State-of-the-art perimetry devices are bulky, thereby precluding application in a spaceflight setting. In contrast, the visual field test & diagnosis system requires only a touchscreen-equipped computer or touchpad device, which may already be in use for other purposes (i.e., no additional payload), and custom software. The system has application in routine astronaut assessment (Clinical Status Exam), pre-, in-, and post-flight monitoring, and astronaut selection. It is deployable in operational space environments, such as aboard the International Space Station or during future missions to or permanent presence on the Moon and Mars.

  9. Field Tests of a Laser Raman Measurement System for Aircraft Engine Exhaust Emissions

    DTIC Science & Technology

    1974-10-01

    practical one. The advantages of optical exhaust gas measurements versus probing systems has been demonstrated. It now remains to solve the remaining...Raman system NOVA digital data processor has the capability to service such additional measurements. If velocity information is desired a study should be...AD/A-003 648 FIELD TESTS OF A LASER RAMAN MEASURE- MENT SYSTEM FOR AIRCRAFT ENGINE EXHAUST EMISSIONS Donald A. Leunard Avoo Everett Researoh

  10. Field Testing of Nano-PCM Enhanced Building Envelope Components

    SciTech Connect

    Biswas, Kaushik; Childs, Phillip W; Atchley, Jerald Allen

    2013-08-01

    The U.S. Department of Energy s (DOE) Building Technologies Program s goal of developing high-performance, energy efficient buildings will require more cost-effective, durable, energy efficient building envelopes. Forty-eight percent of the residential end-use energy consumption is spent on space heating and air conditioning. Reducing envelope-generated heating and cooling loads through application of phase change material (PCM)-enhanced envelope components can facilitate maximizing the energy efficiency of buildings. Field-testing of prototype envelope components is an important step in estimating their energy benefits. An innovative phase change material (nano-PCM) was developed with PCM encapsulated with expanded graphite (interconnected) nanosheets, which is highly conducive for enhanced thermal storage and energy distribution, and is shape-stable for convenient incorporation into lightweight building components. During 2012, two test walls with cellulose cavity insulation and prototype PCM-enhanced interior wallboards were installed in a natural exposure test (NET) facility at Charleston, SC. The first test wall was divided into four sections, which were separated by wood studs and thin layers of foam insulation. Two sections contained nano-PCM-enhanced wallboards: one was a three-layer structure, in which nano-PCM was sandwiched between two gypsum boards, and the other one had PCM dispersed homogeneously throughout graphite nanosheets-enhanced gypsum board. The second test wall also contained two sections with interior PCM wallboards; one contained nano-PCM dispersed homogeneously in gypsum and the other was gypsum board containing a commercial microencapsulated PCM (MEPCM) for comparison. Each test wall contained a section covered with gypsum board on the interior side, which served as control or a baseline for evaluation of the PCM wallboards. The walls were instrumented with arrays of thermocouples and heat flux transducers. Further, numerical modeling of

  11. Pairwise-additive force fields for selected aqueous monovalent ions from adaptive force matching

    PubMed Central

    Li, Jicun; Wang, Feng

    2015-01-01

    Simple non-polarizable potentials were developed for Na+, K+, Cl−, and Br− using the adaptive force matching (AFM) method with ab initio MP2 method as reference. Our MP2-AFM force field predicts the solvation free energies of the four salts formed by the ions with an error of no more than 5%. Other properties such as the ion-water radial distribution functions, first solvation shell water tilt angle distributions, ion diffusion constants, concentration dependent diffusion constant of water, and concentration dependent surface tension of the solutions were calculated with this potential. Very good agreement was achieved for these properties. In particular, the diffusion constants of the ions are within 6% of experimental measurements. The model predicts bromide to be enriched at the interface in the 1.6M KBr solution but predicts the ion to be repelled for the surface at lower concentration. PMID:26590540

  12. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... quantitative problem-solving skills, the test publisher must provide— (i) A minimum of four parallel forms of... the American Educational Research Association, the American Psychological Association, and...

  13. A field test of the TIME patient simulation model.

    PubMed

    Harless, W G; Duncan, R C; Zier, M A; Ayers, W R; Berman, J R; Pohl, H S

    1990-05-01

    The Technological Innovations in Medical Education (TIME) Project has created an interactive videodisc patient-simulation model that provides faculty with a new method for patient-centered teaching in the medical school classroom. The TIME model is designed to be controlled by a professor in the classroom setting, and incorporates voice recognition technology and video dramatization to create a believable patient encounter. Under the auspices of the Lister Hill National Center for Biomedical Communications, National Library of Medicine, where the Project originated in 1983, three medical schools participated in a field test of this "high-tech" model. Six faculty members made ten classroom presentations of two TIME simulations to 306 second-year medical students. The principal finding was that, in a group setting, a large majority of the students at all three schools became individually committed to the care and management of the simulated patient. They acted as if the patient's problems were real and left the session feeling as though they had interacted with an actual person. Therefore, in terms of simulating a real patient, the TIME patient-simulation model was validated, providing the basis for the development of new patient-centered methods to teach and test medical students in the classroom setting. The Project has been at the Georgetown University School of Medicine, where the model is being introduced into the existing curriculum, since 1988. It is currently being used as a part of the final examination for second-year students and in discussion-group settings for fourth-year students in the internal medicine clerkship. A field test is also under way using the TIME model to assess the clinical performance of third-year students.

  14. Direct-field acoustic testing of a flight system : logistics, challenges, and results.

    SciTech Connect

    Stasiunas, Eric Carl; Gurule, David Joseph; Babuska, Vit; Skousen, Troy J.

    2010-10-01

    Before a spacecraft can be considered for launch, it must first survive environmental testing that simulates the launch environment. Typically, these simulations include vibration testing performed using an electro-dynamic shaker. For some spacecraft however, acoustic excitation may provide a more severe loading environment than base shaker excitation. Because this was the case for a Sandia Flight System, it was necessary to perform an acoustic test prior to launch in order to verify survival due to an acoustic environment. Typically, acoustic tests are performed in acoustic chambers, but because of scheduling, transportation, and cleanliness concerns, this was not possible. Instead, the test was performed as a direct field acoustic test (DFAT). This type of test consists of surrounding a test article with a wall of speakers and controlling the acoustic input using control microphones placed around the test item, with a closed-loop control system. Obtaining the desired acoustic input environment - proto-flight random noise input with an overall sound pressure level (OASPL) of 146.7 dB-with this technique presented a challenge due to several factors. An acoustic profile with this high OASPL had not knowingly been obtained using the DFAT technique prior to this test. In addition, the test was performed in a high-bay, where floor space and existing equipment constrained the speaker circle diameter. And finally, the Flight System had to be tested without contamination of the unit, which required a contamination bag enclosure of the test unit. This paper describes in detail the logistics, challenges, and results encountered while performing a high-OASPL, direct-field acoustic test on a contamination-sensitive Flight System in a high-bay environment.

  15. The Field Lysimeter Test Facility (FLTF) at the Hanford Site: Installation and initial tests

    SciTech Connect

    Gee, G.W.; Kirkham, R.R.; Downs, J.L.; Campbell, M.D.

    1989-02-01

    The objectives of this program are to test barrier design concepts and to demonstrate a barrier design that meets established performance criteria for use in isolating wastes disposed of near-surface at the Hanford Site. Specifically, the program is designed to assess how well the barriers perform in controlling biointrusion, water infiltration, and erosion, as well as evaluating interactions between environmental variables and design factors of the barriers. To assess barrier performance and design with respect to infiltration control, field lysimeters and small- and large-scale field plots are planned to test the performance of specific barrier designs under actual and modified (enhanced precipitation) climatic conditions. The Field Lysimeter Test Facility (FLTF) is located in the 600 Area of the Hanford Site just east of the 200 West Area and adjacent to the Hanford Meteorological Station. The FLTF data will be used to assess the effectiveness of selected protective barrier configurations in controlling water infiltration. The facility consists of 14 drainage lysimeters (2 m dia x 3 m deep) and four precision weighing lysimeters (1.5 m x 1.5 m x 1.7 m deep). The lysimeters are buried at grade and aligned in a parallel configuration, with nine lysimeters on each side of an underground instrument chamber. The lysimeters were filled with materials to simulate a multilayer protective barrier system. Data gathered from the FLTF will be used to compare key barrier components and to calibrate and test models for predicting long-term barrier performance.

  16. 75 FR 2122 - Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ... ensure the consistent application of DOE's current test procedure to refrigerator-freezers with French doors, bottom-mounted freezers, and through-the-door (TTD) ice service (French door TTD models). This... application of the current test procedure to refrigerator- freezers with French doors, bottom-mounted...

  17. Field tests prove microscale NRU to upgrade low-btu gas

    USGS Publications Warehouse

    Bhattacharya, S.; David, Newell K.; Lynn, Watney W.; Sigel, M.

    2009-01-01

    The Kansas Geological Survey (University of Kansas) and the American Energies Corp., Wichita, have conducted field tests of a scalable, microscale, N2-rejection unit (NRU) to demonstrate its effectiveness to upgrade low-pressure ((<100 psig) and low-volume (=100 Mcfd) low-btu gas to pipeline quality. The tests aim to develop inexpensive NRU technology, which is designed for low- volume, low-pressure gas wells, to significantly increase the contribution of marginal low-btu gas to the gas supply of the US. The NRU uses two towers and uses three stages, namely, adsorption under pressure, venting to 2 psig, and desorption under vacuum. The modular design allows additional sets of towers to be added or removed to handle increases or decreases in feed volumes. The field tests also reveal that a strong compressor, which is capable of evacuating the tower (volume) as quickly as possible, should be employed to reduce process cycle time and increase plant throughput.

  18. Laboratory endurance testing of a 25/75 sunflower oil-diesel fuel blend treated with fuel additives

    SciTech Connect

    Ziejewski, M.; Kaufman, K.R.; Tupa, R.C.

    1984-01-01

    The engine performance and durability effects of a barium smoke suppressant additive, Lubrizol 565, and an ashless polymeric additive, Lubrizol 552, in a 25-75 blend (v/v) of alkali refined sunflower oil with diesel fuel were investigated. The study was performed on a direct injected, turbocharged, and intercooled diesel engine. These additives were tested in an attempt to reduce carbon buildup problems observed while using an untreated 25-75 blend of sunflower oil and diesel fuel.

  19. MIXTURES OF THYROID DISRUPTING CHEMICALS: TESTING ADDITIVITY OF HEPATIC INDUCERS AND THYROID PEROXIDASE INHIBITORS.

    EPA Science Inventory

    Humans are exposed to chemical mixtures via diet, occupation, and the environment. Previous data demonstrated that low doses of polycyclic halogenated aromatic hydrocarbons (PHAHs) acting through similar mechanisms result in an additive reduction of thyroxine (T4). If xenobioti...

  20. Cooperative field test program for wind systems. Final report

    SciTech Connect

    Bollmeier, W.S. II; Dodge, D.M.

    1992-03-01

    The objectives of the Federal Wind Energy Program, managed by the US Department of Energy (DOE), are (1) to assist industry and utilities in achieving a multi-regional US market penetration of wind systems, and (2) to establish the United States as the world leader in the development of advanced wind turbine technology. In 1984, the program conducted a series of planning workshops with representatives from the wind energy industry to obtain input on the Five-Year Research Plan then being prepared by DOE. One specific suggestion that came out of these meetings was that the federal program should conduct cooperative research tests with industry to enhance the technology transfer process. It was also felt that the active involvement of industry in DOE-funded research would improve the state of the art of wind turbine technology. DOE established the Cooperative Field Test Program (CFTP) in response to that suggestion. This program was one of the first in DOE to feature joint industry-government research test teams working toward common objectives.

  1. Design and Field Test of a Galvanometer Deflected Streak Camera

    SciTech Connect

    Lai, C C; Goosman, D R; Wade, J T; Avara, R

    2002-11-08

    We have developed a compact fieldable optically-deflected streak camera first reported in the 20th HSPP Congress. Using a triggerable galvanometer that scans the optical signal, the imaging and streaking function is an all-optical process without incurring any photon-electron-photon conversion or photoelectronic deflection. As such, the achievable imaging quality is limited mainly only by optical design, rather than by multiple conversions of signal carrier and high voltage electron-optics effect. All core elements of the camera are packaged into a 12 inch x 24 inch footprint box, a size similar to that of a conventional electronic streak camera. At LLNL's Site-300 Test Site, we have conducted a Fabry-Perot interferometer measurement of fast object velocity using this all-optical camera side-by-side with an intensified electronic streak camera. These two cameras are configured as two independent instruments for recording synchronously each branch of the 50/50 splits from one incoming signal. Given the same signal characteristics, the test result has undisputedly demonstrated superior imaging performance for the all-optical streak camera. It produces higher signal sensitivity, wider linear dynamic range, better spatial contrast, finer temporal resolution, and larger data capacity as compared with that of the electronic counterpart. The camera had also demonstrated its structural robustness and functional consistence to be well compatible with field environment. This paper presents the camera design and the test results in both pictorial records and post-process graphic summaries.

  2. Field testing of sound absorption coefficients in a classroom

    NASA Astrophysics Data System (ADS)

    Pettyjohn, Steve

    2005-09-01

    Formal procedures for determining the sound absorption coefficients of materials installed in the field do not exist. However, the U.S. Air Force requested such tests to prove that the sound-absorbing material used in classrooms at Beale AFB in Marysville, CA, met the specified NRC of 0.80. They permitted the use of two layers of 0.5-in. fiberboard or 1-in.-thick fiberglass panels to meet the specified NRC rating. Post-construction tests showed reverberation times longer than expected. Unrealistic sound-absorption coefficients for room finish materials had to be used with the Sabine equation to achieve agreement between the measured and predicted reverberation time. By employing the Fitzroy equation and generally published absorption coefficients for ceiling tile, carpet, and fiberboard, the model provided excellent agreement with the measured reverberation times. The NRC of the fiberboard was computed to be 0.35, agreeing with published data. Since this did not meet project specifications, the Fitzroy model was used to learn the type and quantity of material needed to meet design goals. Follow-up tests showed good agreement between the predicted and measured reverberation times with material added, and project specifications were met. Results are also compared with the requirements of ANSI 12.60.

  3. UV-accelerated test based on analysis of field-exposed PV modules

    NASA Astrophysics Data System (ADS)

    Shioda, T.

    2011-09-01

    We proposed an UV accelerated test condition for an EVA encapsulant, based on analysis of long term field exposed PV modules. We found that strong UV irradiation into EVA encapsulant test sample led to the fast decomposition of UV absorber formulated in EVA encapsulant, which has never seen in the field exposed PV modules. Thus, the integrating UV intensity of 60 W/m2 and black panel temperature of 110°C using a xenon weather-o-meter were suitable as an UV accelerated test condition. With this proposed test condition, which shows that 1 week exposure by xenon light corresponds to 1 year field exposure, we can predict discoloration rate of EVA encapsulant. In addition, we evaluated change in peel strength to glass for Mitsui's and the other commercially available EVA encapsulants during UV accelerated test with the proposed condition. There was no large change in peel strength for our EVA encapsulant during the UV accelerated test. On the other hand, we observed that the competitor's EVA encapsulant showed the large decrease of peel strength to glass at early stage, even no change in yellowness index (YI). This result indicates not only YI change but also peel strength change should be evaluated for design of reliable PV module and encapsulant.

  4. Testing for Additivity in Chemical Mixtures Using a Fixed-Ratio Ray Design and Statistical Equivalence Testing Methods

    EPA Science Inventory

    Fixed-ratio ray designs have been used for detecting and characterizing interactions of large numbers of chemicals in combination. Single chemical dose-response data are used to predict an “additivity curve” along an environmentally relevant ray. A “mixture curve” is estimated fr...

  5. A Comparative Kirkwood-Buff Study of Aqueous Methanol Solutions Modeled by the CHARMM Additive and Drude Polarizable Force Fields

    PubMed Central

    Lin, Bin; He, Xibing; MacKerell, Alexander D.

    2013-01-01

    A comparative study on aqueous methanol solutions modeled by the CHARMM additive and Drude polarizable force fields was carried out by employing Kirkwood-Buff analysis. It was shown that both models reproduced the experimental Kirkwood-Buff integrals and excess coordination numbers adequately well over the entire concentration range. The Drude model showed significant improvement over the additive model in solution densities, partial molar volumes, excess molar volumes, concentration-dependent diffusion constants, and dielectric constants. However, the additive model performed somewhat better than the Drude model in reproducing the activity derivative, excess molar Gibbs energy and excess molar enthalpy of mixing. This is due to the additive achieving a better balance among solute-solute, solute-solvent, and solvent-solvent interactions, indicating the potential for improvements in the Drude polarizable alcohol model. PMID:23947568

  6. Design and test of field programmable gate arrays in space applications

    NASA Technical Reports Server (NTRS)

    Mckerracher, Priscilla L.; Cain, Russel P.; Barnett, Jon C.; Green, William S.; Kinnison, James D.

    1992-01-01

    Field Programmable Gate Arrays (FPGAU's) offer substantial benefits in terms of flexibility and design integration. In addition to qualifying this device for space applications by establishing its reliability and evaluating its sensitivity to radiation, screening the programmed devices with Automatic Test Equipment (ATE) and functional burn-in presents an interesting challenge. This paper presents a review of the design, qualification, and screening cycle employed for FPGA designs in a space program, and demonstrates the need for close interaction between design and test engineers.

  7. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  8. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  9. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  10. Field Evidence for Co-Metabolism of Trichloroethene Stimulated by Addition of Electron Donor to Groundwater

    SciTech Connect

    Conrad, Mark E.; Brodie, Eoin L.; Radtke, Corey W.; Bill, Markus; Delwiche, Mark E.; Lee, M. Hope; Swift, Dana L.; Colwell, Frederick S.

    2010-05-17

    For more than 10 years, electron donor has been injected into the Snake River aquifer beneath the Test Area North site of the Idaho National Laboratory for the purpose of stimulating microbial reductive dechlorination of trichloroethene (TCE) in groundwater. This has resulted in significant TCE removal from the source area of the contaminant plume and elevated dissolved CH4 in the groundwater extending 250 m from the injection well. The delta13C of the CH4 increases from 56o/oo in the source area to -13 o/oo with distance from the injection well, whereas the delta13C of dissolved inorganic carbon decreases from 8 o/oo to -13 o/oo, indicating a shift from methanogenesis to methane oxidation. This change in microbial activity along the plume axis is confirmed by PhyloChip microarray analyses of 16S rRNA genes obtained from groundwater microbial communities, which indicate decreasing abundances of reductive dechlorinating microorganisms (e.g., Dehalococcoides ethenogenes) and increasing CH4-oxidizing microorganisms capable of aerobic co-metabolism of TCE (e.g., Methylosinus trichosporium). Incubation experiments with 13C-labeled TCE introduced into microcosms containing basalt and groundwater from the aquifer confirm that TCE co-metabolism is possible. The results of these studies indicate that electron donor amendment designed to stimulate reductive dechlorination of TCE may also stimulate co-metabolism of TCE.

  11. Near-field modeling in Frenchman Flat, Nevada Test Site

    SciTech Connect

    Pohlmann, K.; Shirley, C.; Andricevic, R.

    1996-12-01

    The US Department of Energy (DOE) is investigating the effects of nuclear testing in underground test areas (the UGTA program) at the Nevada Test Site. The principal focus of the UGTA program is to better understand and define subsurface radionuclide migration. The study described in this report focuses on the development of tools for generating maps of hydrogeologic characteristics of subsurface Tertiary volcanic units at the Frenchman Flat corrective Action Unit (CAU). The process includes three steps. The first step involves generation of three-dimensional maps of the geologic structure of subsurface volcanic units using geophysical logs to distinguish between two classes: densely welded tuff and nonwelded tuff. The second step generates three-dimensional maps of hydraulic conductivity utilizing the spatial distribution of the two geologic classes obtained in the first step. Each class is described by a correlation structure based on existing data on hydraulic conductivity, and conditioned on the generated spatial location of each class. The final step demonstrates the use of the maps of hydraulic conductivity for modeling groundwater flow and radionuclide transport in volcanic tuffs from an underground nuclear test at the Frenchman Flat CAU. The results indicate that the majority of groundwater flow through the volcanic section occurs through zones of densely welded tuff where connected fractures provide the transport pathway. Migration rates range between near zero to approximately four m/yr, with a mean rate of 0.68 m/yr. This report presents the results of work under the FY96 Near-Field Modeling task of the UGTA program.

  12. Acoustic Nondestructive Testing and Measurement of Tension for Steel Reinforcing Members: Part 2 - Field Testing

    DTIC Science & Technology

    2014-09-01

    BACKGROUND: Many reinforced concrete structures contain embedded pre- and post- tensioned steel members that are subject to corrosion and fracturing...Tension for Steel Reinforcing Members Part 2 – Field Testing by Michael K. McInerney PURPOSE: This Coastal and Hydraulics Engineering Technical...Specifically, the technology application addresses the problem of determining tension in concrete -embedded pre- and post-tensioned reinforcement rods

  13. A field test of a simple stochastic radiative transfer model

    SciTech Connect

    Byrne, N.

    1995-09-01

    The problem of determining the effect of clouds on the radiative energy balance of the globe is of well-recognized importance. One can in principle solve the problem for any given configuration of clouds using numerical techniques. This knowledge is not useful however, because of the amount of input data and computer resources required. Besides, we need only the average of the resulting solution over the grid scale of a general circulation model (GCM). Therefore, we are interested in estimating the average of the solutions of such fine-grained problems using only coarse grained data, a science or art called stochastic radiation transfer. Results of the described field test indicate that the stochastic description is a somewhat better fit to the data than is a fractional cloud cover model, but more data are needed. 1 ref., 3 figs.

  14. Field Tested Service Oriented Robotic Architecture: Case Study

    NASA Technical Reports Server (NTRS)

    Flueckiger, Lorenzo; Utz, Hanz

    2012-01-01

    This paper presents the lessons learned from six years of experiments with planetary rover prototypes running the Service Oriented Robotic Architecture (SORA) developed by the Intelligent Robotics Group (IRG) at NASA Ames Research Center. SORA relies on proven software methods and technologies applied to the robotic world. Based on a Service Oriented Architecture and robust middleware, SORA extends its reach beyond the on-board robot controller and supports the full suite of software tools used during mission scenarios from ground control to remote robotic sites. SORA has been field tested in numerous scenarios of robotic lunar and planetary exploration. The results of these high fidelity experiments are illustrated through concrete examples that have shown the benefits of using SORA as well as its limitations.

  15. Testing Einstein's Equivalence Principle with supercluster Laniakea's gravitational field

    NASA Astrophysics Data System (ADS)

    Luo, Zhi-Xing; Zhang, Bo; Wei, Jun-Jie; Wu, Xue-Feng

    2016-03-01

    Comparing the parameterized post-Newtonian parameter γ values for different types of particles, or the same type of particles with different energies is an important method to test the Einstein Equivalence Principle (EEP). Assuming that the observed time delays are dominated by the gravitational potential of the Laniakea supercluster of galaxies, better results of EEP constraints can be obtained. In this paper, we apply photons from three kinds of cosmic transients, including TeV blazars, gamma-ray bursts as well as fast radio bursts to constrain EEP. With a gravitational field far more stronger than a single galaxy, we obtain 4-5 orders of magnitude more stringent than the previous results.

  16. Test of the Additivity Principle for Current Fluctuations in a Model of Heat Conduction

    NASA Astrophysics Data System (ADS)

    Hurtado, Pablo I.; Garrido, Pedro L.

    2009-06-01

    The additivity principle allows to compute the current distribution in many one-dimensional (1D) nonequilibrium systems. Using simulations, we confirm this conjecture in the 1D Kipnis-Marchioro-Presutti model of heat conduction for a wide current interval. The current distribution shows both Gaussian and non-Gaussian regimes, and obeys the Gallavotti-Cohen fluctuation theorem. We verify the existence of a well-defined temperature profile associated to a given current fluctuation. This profile is independent of the sign of the current, and this symmetry extends to higher-order profiles and spatial correlations. We also show that finite-time joint fluctuations of the current and the profile are described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

  17. Test of the additivity principle for current fluctuations in a model of heat conduction.

    PubMed

    Hurtado, Pablo I; Garrido, Pedro L

    2009-06-26

    The additivity principle allows to compute the current distribution in many one-dimensional (1D) nonequilibrium systems. Using simulations, we confirm this conjecture in the 1D Kipnis-Marchioro-Presutti model of heat conduction for a wide current interval. The current distribution shows both Gaussian and non-Gaussian regimes, and obeys the Gallavotti-Cohen fluctuation theorem. We verify the existence of a well-defined temperature profile associated to a given current fluctuation. This profile is independent of the sign of the current, and this symmetry extends to higher-order profiles and spatial correlations. We also show that finite-time joint fluctuations of the current and the profile are described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

  18. Vadose Zone Transport Field Study FY 2003 Test Plan

    SciTech Connect

    Ward, Anderson L.; Gee, Glendon W.

    2003-04-15

    Conceptual models have been identified as one of the sources of uncertainty in the interpretation and prediction of contaminant migration through the vadose zone at Hanford. Current conceptual models are limited partly because they often do not account for the random heterogeneity that occurs under the extremes of very nonlinear flow behavior typical of the Hanford vadose zone. Over the last two years significant progress has been made in characterizing physical heterogeneity and in the development of techniques for incorporating this heterogeneity into predictive and inverse models for field-scale subsurface flow. One of the remaining pieces of the puzzle is the impact of heterogeneity on the distribution of reactive contaminants. Reactive transport occurs over a wide range of spatial and temporal scales. However, the manner in which the various subsurface physical and chemical processes interact to influence transport is not very well understood. Hydrogeologic characterization and model analysis, however, have traditionally focused on measurement of physical properties and predicting the effects of variability in these properties on flow and transport. As a result, the role of geochemical heterogeneity on solute transport has remained largely unexplored. This project will use a combination of geophysical and soil physics techniques to investigate the infiltration and redistribution of water and reactive tracers in a controlled field experiment at the Army loop Road clastic dike site. In the FY2003 tests, surface deployed ground penetrating radar will be used to identify the discrete three-dimensional pattern of horizonation and small-scale heterogeneities that characterize the test site and to develop a lithofacies map. The transect will be instrumented to allow water to be applied along its length from a line source. Local-scale water content, matric potential, and tracer concentrations will be monitored as a function of spatial scale by multipurpose TDR probes

  19. Vadose Zone Transport Field Study: Detailed Test Plan for Simulated Leak Tests

    SciTech Connect

    Ward, Anderson L.; Gee, Glendon W.

    2000-06-23

    This report describes controlled transport experiments at well-instrumented field tests to be conducted during FY 2000 in support of DOE?s Vadose Zone Transport Field Study (VZTFS). The VZTFS supports the Groundwater/Vadose Zone Integration Project Science and Technology Initiative. The field tests will improve understanding of field-scale transport and lead to the development or identification of efficient and cost-effective characterization methods. These methods will capture the extent of contaminant plumes using existing steel-cased boreholes. Specific objectives are to 1) identify mechanisms controlling transport processes in soils typical of the hydrogeologic conditions of Hanford?s waste disposal sites; 2) reduce uncertainty in conceptual models; 3) develop a detailed and accurate data base of hydraulic and transport parameters for validation of three-dimensional numerical models; and 4) identify and evaluate advanced, cost-effective characterization methods with the potential to assess changing conditions in the vadose zone, particularly as surrogates of currently undetectable high-risk contaminants. Pacific Northwest National Laboratory (PNNL) manages the VZTFS for DOE.

  20. Effect of nitrate addition on biorestoration of fuel-contaminated aquifer: Field demonstration

    SciTech Connect

    Hutchins, S.R.; Downs, W.C.; Wilson, J.T.; Smith, G.B.; Kovacs, D.A.

    1991-01-01

    A spill of JP-4 jet fuel at the U.S. Coast Guard Air Station in Traverse City, Michigan, contaminated a water-table aquifer. An infiltration gallery (30 ft X 30 ft) was installed above a section of the aquifer containing 700 gal JP-4. Purge wells recirculated three million gallons of ground water per week through the infiltration gallery at a rate designed to raise the water table above the contaminated interval. Ground water containing ambient concentrations was first recirculated for 40 days. Concentrations of benzene in monitoring wells beneath the infiltration gallery were reduced from 760 to <1 micrograms/1. Concentrations of toluene, ethylbenzene, m,p-xylene, and o-xylene were reduced from 4500 to 17,840 to 44,2600 to 490, and 1400 to 260 micrograms/1, respectively. Average core concentrations of benzene, toluene, ethylbenzene, m,p-xylene, and o-xylene were reduced from 0.84 to 0.032, 33 to 0.13, 18 to 0.36, 58 to 7.4, and 26 to 3.2 mg/kg, respectively. Ground water amended with nitrate (10 mg/1 nitrate-nitrogen) and nutrients was then recirculated for 76 days. Final core concentrations of benzene, toluene, ethylbenzene, m,p-xylene and o-xylene were 0.017, 0.036, 0.019, 0.059, and 0.27 mg/kg, respectively. Final aqueous concentrations were <1 micrograms/1 for benzene and toluene, 6 micrograms/1 for ethylbenzene, and 20 to 40 micrograms/1 for the xylene isomers, in good agreement with predicted values based on residual fuel content and partitioning theory. Although alkylbenzene concentrations have been substantially reduced, the test plot is still contaminated with the weathered fuel. Based on stoichiometry, approximately 10 times more nitrate was consumed than could be accounted for by BTX degradation alone, indicating that other compounds were also degraded under denitrifying conditions.

  1. Hanford 100-D Area Biostimulation Soluble Substrate Field Test: Interim Data Summary for the Substrate Injection and Process Monitoring Phases of the Field Test

    SciTech Connect

    Truex, Michael J.; Vermeul, Vincent R.; Mackley, Rob D.; Fritz, Brad G.; Mendoza, Donaldo P.; Johnson, Christian D.; Elmore, Rebecca P.; Brockman, Fred J.; Bilskis, Christina L.

    2008-06-01

    Pacific Northwest National Laboratory is conducting a treatability test designed to demonstrate that in situ biostimulation can be applied to help meet cleanup goals in the Hanford Site 100-D Area. The in situ biostimulation technology is intended to provide supplemental treatment upgradient of the In Situ Redox Manipulation (ISRM) barrier by reducing the concentration of the primary oxidizing species in groundwater (i.e., nitrate and dissolved oxygen) and chromate, and thereby increasing the longevity of the ISRM barrier. This report summarizes the initial results from field testing of an in situ biological treatment zone implemented through injection of a soluble substrate. The field test is divided into operational phases that include substrate injection, process monitoring, and performance monitoring. The results summarized herein are for the substrate injection and process monitoring phase encompassing the first approximately three months of field testing. Performance monitoring is ongoing at the time this report was prepared and is planned to extend over approximately 18 months. As such, this report is an interim data summary report for the field test. The treatability testing has multiple objectives focused on evaluating the performance of biostimulation as a reducing barrier for nitrate, oxygen, and chromate. The following conclusions related to these objectives are supported by the data provided in this report. Substrate was successfully distributed to a radius of about 15 m (50 ft) from the injection well. Monitoring data indicate that microbial growth initiated rapidly, and this rapid growth would limit the ability to inject substrate to significantly larger zones from a single injection well. As would be expected, the uniformity of substrate distribution was impacted by subsurface heterogeneity. However, subsequent microbial activity and ability to reduce the targeted species was observed throughout the monitored zone during the process monitoring

  2. Results of field testing of waste forms using lysimeters

    SciTech Connect

    McConnell, J.W., Jr.; Rogers, R.D.

    1988-01-01

    The purpose of the field testing task, using lysimeter arrays, is to expose samples of solidified resin waste to the actual physical, chemical, and microbiological conditions of disposal enviroment. Wastes used in the experiment include a mixture of synthetic organic ion exchange resins and a mixture of organic exchange resins and an inorganic zeolite. Solidification agents used to produce the 4.8-by 7.6-cm cylindrical waste forms used in the study were Portland Type I-II cement and Dow vinyl ester-styrene. Seven of these waste forms were stacked end-to-end and inserted into each lysimeter to provide a 1-L volume. There are 10 lysimeters, 5 at ORNL and 5 at ANL-E. Lysimeters used in this study were designed to be self-contained units which will be disposed at the termination of the 20-year study. Each is a 0.91-by 3.12-m right-circular cylinder divided into an upper compartment, which contains fill material, waste forms, and instrumentation, and an empty lower compartment, which collects leachate. Four lysimeters at each site are filled with soil, while a fifth (used as a control) is filled with inert silica oxide sand. Instrumentation within each lysimeter includes porous cup soil-water samplers and soil moisture/temperature probes. The probes are connected to an on-site data acquisition and storage system (DAS) which also collects data from a field meteorological station located at each site. 9 refs.

  3. Field-Based Video Pre-Test Counseling, Oral Testing, and Telephonic Post-Test Counseling: Implementation of an HIV Field Testing Package among High-Risk Indian Men

    ERIC Educational Resources Information Center

    Snyder, Hannah; Yeldandi, Vijay V.; Kumar, G. Prem; Liao, Chuanhong; Lakshmi, Vemu; Gandham, Sabitha R.; Muppudi, Uma; Oruganti, Ganesh; Schneider, John A.

    2012-01-01

    In India, men who have sex with men (MSM) and truck drivers are high-risk groups that often do not access HIV testing due to stigma and high mobility. This study evaluated a field testing package (FTP) that identified HIV positive participants through video pre-test counseling, OraQuick oral fluid HIV testing, and telephonic post-test counseling…

  4. Large fluctuations of the macroscopic current in diffusive systems: a numerical test of the additivity principle.

    PubMed

    Hurtado, Pablo I; Garrido, Pedro L

    2010-04-01

    Most systems, when pushed out of equilibrium, respond by building up currents of locally conserved observables. Understanding how microscopic dynamics determines the averages and fluctuations of these currents is one of the main open problems in nonequilibrium statistical physics. The additivity principle is a theoretical proposal that allows to compute the current distribution in many one-dimensional nonequilibrium systems. Using simulations, we validate this conjecture in a simple and general model of energy transport, both in the presence of a temperature gradient and in canonical equilibrium. In particular, we show that the current distribution displays a Gaussian regime for small current fluctuations, as prescribed by the central limit theorem, and non-Gaussian (exponential) tails for large current deviations, obeying in all cases the Gallavotti-Cohen fluctuation theorem. In order to facilitate a given current fluctuation, the system adopts a well-defined temperature profile different from that of the steady state and in accordance with the additivity hypothesis predictions. System statistics during a large current fluctuation is independent of the sign of the current, which implies that the optimal profile (as well as higher-order profiles and spatial correlations) are invariant upon current inversion. We also demonstrate that finite-time joint fluctuations of the current and the profile are well described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

  5. Large fluctuations of the macroscopic current in diffusive systems: A numerical test of the additivity principle

    NASA Astrophysics Data System (ADS)

    Hurtado, Pablo I.; Garrido, Pedro L.

    2010-04-01

    Most systems, when pushed out of equilibrium, respond by building up currents of locally conserved observables. Understanding how microscopic dynamics determines the averages and fluctuations of these currents is one of the main open problems in nonequilibrium statistical physics. The additivity principle is a theoretical proposal that allows to compute the current distribution in many one-dimensional nonequilibrium systems. Using simulations, we validate this conjecture in a simple and general model of energy transport, both in the presence of a temperature gradient and in canonical equilibrium. In particular, we show that the current distribution displays a Gaussian regime for small current fluctuations, as prescribed by the central limit theorem, and non-Gaussian (exponential) tails for large current deviations, obeying in all cases the Gallavotti-Cohen fluctuation theorem. In order to facilitate a given current fluctuation, the system adopts a well-defined temperature profile different from that of the steady state and in accordance with the additivity hypothesis predictions. System statistics during a large current fluctuation is independent of the sign of the current, which implies that the optimal profile (as well as higher-order profiles and spatial correlations) are invariant upon current inversion. We also demonstrate that finite-time joint fluctuations of the current and the profile are well described by the additivity functional. These results suggest the additivity hypothesis as a general and powerful tool to compute current distributions in many nonequilibrium systems.

  6. Additional Clarification of Intercollegiate Athletics Policy: Three-Part Test. Part Three

    ERIC Educational Resources Information Center

    US Department of Education, 2005

    2005-01-01

    This Additional Clarification, "User's Guide to Developing Student Interest Surveys Under Title IX" (User's Guide), and related technical report are resources to assist institutions in meeting their compliance obligations. Taken together, they serve to clarify many of the factors OCR will consider under part three, and to facilitate…

  7. Testing a Gender Additive Model: The Role of Body Image in Adolescent Depression

    ERIC Educational Resources Information Center

    Bearman, Sarah Kate; Stice, Eric

    2008-01-01

    Despite consistent evidence that adolescent girls are at greater risk of developing depression than adolescent boys, risk factor models that account for this difference have been elusive. The objective of this research was to examine risk factors proposed by the "gender additive" model of depression that attempts to partially explain the increased…

  8. 76 FR 3075 - Availability of an Environmental Assessment for Field Testing Feline Leukemia Vaccine, Live...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-19

    ... Feline Leukemia Vaccine, Live Canarypox Vector AGENCY: Animal and Plant Health Inspection Service, USDA... testing, and then to field test, an unlicensed Feline Leukemia Vaccine, Live Canarypox Vector. The... field testing of this vaccine, examines the potential effects that field testing this veterinary...

  9. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing conducted with engines installed in vehicles, including field testing conducted to measure emissions under...

  10. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 20 2013-07-01 2013-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing conducted with engines installed in vehicles, including field testing conducted to measure emissions under...

  11. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 20 2012-07-01 2012-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing conducted with engines installed in vehicles, including field testing conducted to measure emissions under...

  12. 40 CFR 86.1375-2007 - Equipment specifications for field testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 19 2011-07-01 2011-07-01 false Equipment specifications for field... Exhaust Test Procedures § 86.1375-2007 Equipment specifications for field testing. For testing conducted with engines installed in vehicles, including field testing conducted to measure emissions under...

  13. Field validation of 10-day freshwater sediment toxicity tests using Hyalella azteca and Chironomus tentans

    SciTech Connect

    Becker, D.S.; Bigham, G.N.

    1995-12-31

    Two of the toxicity tests commonly used to evaluate freshwater sediments are the 10-day amphipod (Hyalella azteca) and chironomid (Chironomus tentans) tests. EPA and ASTM have recently developed standardized protocols for these tests. Although both tests are considered sensitive indicators of sediment toxicity, little information exists on how well test results correspond to adverse biological effects in the field. In this study, the lethal and sublethal (i.e., biomass) responses of the two toxicity tests were compared with alterations of benthic macroinvertebrate assemblages (i.e., benthic effects) at 56 stations in Onondaga Lake, New York. The lake has received municipal and industrial discharges for more than 100 years, and sediment chemical concentrations range widely throughout the lake. Toxicity results for Onondaga Lake were compared with reference conditions using the t-test, and benthic effects were determined using classification analysis of log-transformed taxa abundances. In general, a relatively high level of agreement was found between results of the toxicity tests and alterations of benthic assemblages. Significant (P < 0.05) correlations were found between all toxicity test endpoints and taxa richness of benthic assemblages. In addition, significant concordance (P {le} 0.01, binomial test) was found between toxicity designations for the 56 stations based on toxicity tests and toxicity designations based on benthic effects. Despite the general level of agreement among the various biological indicators, chironomid biomass and benthic effects were found to be the most sensitive indicators of toxicity, whereas amphipod survival and biomass were the least sensitive indicators. This study suggests that results of the 10-day amphipod and chironomid toxicity tests are highly predictive of adverse biological effects in the field.

  14. Temperature and Magnetic Field Dependence of Critical Current Density of YBCO with Varying Flux Pinning Additions (POSTPRINT)

    DTIC Science & Technology

    2010-03-01

    coverage corresponding to M phase 1 nm thickness was found to be necessary to increase compared to YBCO . The op- timal layer thickness for each M phase was...kept constant in this experiment: , Y211 0.8 nm , and [17]. Using the optimal M phase thickness, the YBCO layer was also systematically varied for...AFRL-RZ-WP-TP-2010-2083 TEMPERATURE AND MAGNETIC FIELD DEPENDENCE OF CRITICAL CURRENT DENSITY OF YBCO WITH VARYING FLUX PINNING ADDITIONS

  15. Portable narcotics detector and the results obtained in field tests

    NASA Astrophysics Data System (ADS)

    Tumer, Tumay O.; Su, Chih-Wu; Kaplan, Christopher R.; Rigdon, Stephen W.

    1997-02-01

    A compact integrated narcotics detection instrument (CINDI) has been developed at NOVA R&D, Inc. with funding provided by the U.S. Coast Guard. CINDI is designed as a portable sensitive neutron backscatter detector which has excellent penetration for thick and high Z compartment barriers. It also has a highly sensitive detection system for backscattered neutrons and, therefore, uses a very weak californium-252 neutron source. Neutrons backscatter profusely from materials that have a large hydrogen content, such as narcotics. The rate of backscattered neutrons detected is analyzed by a microprocessor and displayed on the control panel. The operator guides the detector along a suspected area and displays in real time the backscattered neutron rate. CINDI is capable of detecting narcotics effectively behind panels made of steel, wood, fiberglass, or even lead-lined materials. This makes it useful for inspecting marine vessels, ship bulkheads, automobiles, structure walls or small sealed containers. The strong response of CINDI to hydrogen-rich materials such as narcotics makes it an effective tool for detecting concealed drugs. Its response has been field tested by NOVA, the U.S. Coast Guard and Brewt Power Systems. The results of the tests show excellent response and specificity to narcotic drugs. Several large shipments of concealed drugs have been discovered during these trials and the results are presented and discussed.

  16. Brine treatment test for reinjection on Cerro Prieto geothermal field

    SciTech Connect

    Hurtado, R.; Mercado, S.; Gamino, H. )

    1989-01-01

    Reinjection of disposal brine from the Cerro Prieto Geothermal Power Plant System is attractive mainly because, on top of solving the brine disposal problem, it may significantly contribute to extend the reservoir useful lifetime, through thermal and hydraulic recharge. Because the high concentration of colloidal silica in the disposal brine, laboratory and pilot plant tests were conducted in order to develop the brine treatment process. Addition of 20-40 mg/1 lime to flashed and aged brine for 10-20 minutes yields a clarified brine relatively low in suspended solids (10-30 mg/1) when the over flow rate is 38.5 1/min-m/sup 2/. 1.1 mills/kWh was the estimated cost for treatment of 800 kg/s of separated brine from the Cerro Prieto I power station.

  17. Field Testing the STRATA Ground Penetrating Radar for Mars

    NASA Astrophysics Data System (ADS)

    Williams, K. K.; Grant, J. A.; Leuschen, C. J.; Schutz, A. E.

    2005-12-01

    With the MARSIS and SHARAD orbital radar sounders now in operation at and in transit to Mars, respectively, radar investigation of the deep structure of Mars down to several kilometers is underway. By contrast, optical and thermal instruments both in orbit and on the surface have provided information about the top several millimeters and the Mars Exploration Rovers have dug to several cm with their wheels. Nevertheless, little is known about the shallow subsurface of Mars to depths of meters except at locations where continuation of outcrop into the subsurface can be extrapolated. As the methods for exploring Mars evolve, the utility of ground penetrating radar (GPR) for investigating the shallow subsurface of that planet is being considered. GPR has been used for several decades on Earth as a non-invasive tool for studying subsurface structures and stratigraphy for applications in geology, engineering, and archaeology. The STRATA GPR for Mars has been developed as an adaptable, low power, compact, rover-mounted instrument capable of penetrating 10-20 m to reveal subsurface information. Field-testing of this instrument has taken place in volcanic, cratered, permafrost, and deltaic settings, and data collected at 400 MHz possess vertical resolutions of a few cm, sufficient to interpret the subsurface geologic setting. Results from the permafrost environment showed detection of buried massive ground ice as well as the base of the active layer. GPR analysis of this ice distribution was confirmed by resistivity measurements. The fine vertical resolution and good penetration in a variety of geologic settings show that the STRATA instrument provides data quality indistinguishable from commercial systems used on Earth. Most recently, the STRATA instrument has been tested in aeolian and filled crater environments. Data were collected over a sand dune overlying a basalt lava flow near St. Anthony, ID, and at the Campo del Cielo impact crater field in Chaco Province

  18. Results from laboratory and field testing of nitrate measuring spectrophotometers

    USGS Publications Warehouse

    Snazelle, Teri T.

    2015-01-01

    In Phase II, the analyzers were deployed in field conditions at three diferent USGS sites. The measured nitrate concentrations were compared to discrete (reference) samples analyzed by the Direct UV method on a Shimadzu UV1800 bench top spectrophotometer, and by the National Environmental Methods Index (NEMI) method I-2548-11 at the USGS National Water Quality Laboratory. The first deployment at USGS site 0249620 on the East Pearl River in Hancock County, Mississippi, tested the ability of the TriOs ProPs (10-mm path length), Hach NITRATAX (5 mm), Satlantic SUNA (10 mm), and the S::CAN Spectro::lyser (5 mm) to accurately measure low-level (less than 2 mg-N/L) nitrate concentrations while observing the effect turbidity and colored dissolved organic matter (CDOM) would have on the analyzers' measurements. The second deployment at USGS site 01389005 Passaic River below Pompton River at Two Bridges, New Jersey, tested the analyzer's accuracy in mid-level (2-8 mg-N/L) nitrate concentrations. This site provided the means to test the analyzers' performance in two distinct matrices—the Passaic and the Pompton Rivers. In this deployment, three instruments tested in Phase I (TriOS, Hach, and SUNA) were deployed with the S::CAN Spectro::lyser (35 mm) already placed by the New Jersey Water Science Center (WSC). The third deployment at USGS site 05579610 Kickapoo Creek at 2100E Road near Bloomington, Illinois, tested the ability of the analyzers to measure high nitrate concentrations (greater than 8 mg-N/L) in turbid waters. For Kickapoo Creek, the HIF provided the TriOS (10 mm) and S::CAN (5 mm) from Phase I, and a SUNA V2 (5 mm) to be deployed adjacent to the Illinois WSC-owned Hach (2 mm). A total of 40 discrete samples were collected from the three deployment sites and analyzed. The nitrate concentration of the samples ranged from 0.3–22.2 mg-N/L. The average absolute difference between the TriOS measurements and discrete samples was 0.46 mg-N/L. For the combined data

  19. Towards strong field tests of beyond Horndeski gravity theories

    NASA Astrophysics Data System (ADS)

    Sakstein, Jeremy; Babichev, Eugeny; Koyama, Kazuya; Langlois, David; Saito, Ryo

    2017-03-01

    Theories of gravity in the beyond Horndeski class encompass a wide range of scalar-tensor theories that will be tested on cosmological scales over the coming decade. In this work, we investigate the possibility of testing them in the strong field regime by looking at the properties of compact objects—neutron, hyperon, and quark stars—embedded in an asymptotically de Sitter space-time, for a specific subclass of theories. We extend previous works to include slow rotation and find a relation between the dimensionless moment of inertia (I ¯ =I c2/GNM3 ) and the compactness C =GNM /R c2 (an I ¯-C relation), independent of the equation of state, that is reminiscent of but distinct from the general relativity prediction. Several of our equations of state contain hyperons and free quarks, allowing us to revisit the hyperon puzzle. We find that the maximum mass of hyperon stars can be larger than 2 M⊙ for small values of the beyond Horndeski parameter, thus providing a resolution of the hyperon puzzle based on modified gravity. Moreover, stable quark stars exist when hyperonic stars are unstable, which means that the phase transition from hyperon to quark stars is predicted just as in general relativity (GR), albeit with larger quark star masses. Two important and potentially observable consequences of some of the theories we consider are the existence of neutron stars in a range of masses significantly higher than in GR and I ¯-C relations that differ from their GR counterparts. In the former case, we find objects that, if observed, could not be accounted for in GR because they violate the usual GR causality condition. We end by discussing several difficult technical issues that remain to be addressed in order to reach more realistic predictions that may be tested using gravitational wave searches or neutron star observations.

  20. Field testing advanced geothermal turbodrill (AGT). Phase 1 final report

    SciTech Connect

    Maurer, W.C.; Cohen, J.H.

    1999-06-01

    Maurer Engineering developed special high-temperature geothermal turbodrills for LANL in the 1970s to overcome motor temperature limitations. These turbodrills were used to drill the directional portions of LANL`s Hot Dry Rock Geothermal Wells at Fenton Hill, New Mexico. The Hot Dry Rock concept is to drill parallel inclined wells (35-degree inclination), hydraulically fracture between these wells, and then circulate cold water down one well and through the fractures and produce hot water out of the second well. At the time LANL drilled the Fenton Hill wells, the LANL turbodrill was the only motor in the world that would drill at the high temperatures encountered in these wells. It was difficult to operate the turbodrills continuously at low speed due to the low torque output of the LANL turbodrills. The turbodrills would stall frequently and could only be restarted by lifting the bit off bottom. This allowed the bit to rotate at very high speeds, and as a result, there was excessive wear in the bearings and on the gauge of insert roller bits due to these high rotary speeds. In 1998, Maurer Engineering developed an Advanced Geothermal Turbodrill (AGT) for the National Advanced Drilling and Excavation Technology (NADET) at MIT by adding a planetary speed reducer to the LANL turbodrill to increase its torque and reduce its rotary speed. Drilling tests were conducted with the AGT using 12 1/2-inch insert roller bits in Texas Pink Granite. The drilling tests were very successful, with the AGT drilling 94 ft/hr in Texas Pink Granite compared to 45 ft/hr with the LANL turbodrill and 42 ft/hr with a rotary drill. Field tests are currently being planned in Mexico and in geothermal wells in California to demonstrate the ability of the AGT to increase drilling rates and reduce drilling costs.

  1. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... request, the sample may be discarded following the end of the 365-day period. (b) If the medical review officer (MRO) determines there is no legitimate medical explanation for a confirmed positive test result... and Human Services. The operator may require the employee to pay in advance the cost of shipment...

  2. Software for Information Storage and Retrieval Tested, Evaluated and Compared: Part VI--Various Additional Programs.

    ERIC Educational Resources Information Center

    Sieverts, Eric G.; And Others

    1993-01-01

    Reports on tests evaluating nine microcomputer software packages designed for information storage and retrieval: BRS-Search, dtSearch, InfoBank, Micro-OPC, Q&A, STN-PFS, Strix, TINman, and ZYindex. Tables and narrative evaluations detail results related to security, hardware, user features, search capability, indexing, input, maintenance of files,…

  3. Terahertz imaging and tomography as efficient instruments for testing polymer additive manufacturing objects.

    PubMed

    Perraud, J B; Obaton, A F; Bou-Sleiman, J; Recur, B; Balacey, H; Darracq, F; Guillet, J P; Mounaix, P

    2016-05-01

    Additive manufacturing (AM) technology is not only used to make 3D objects but also for rapid prototyping. In industry and laboratories, quality controls for these objects are necessary though difficult to implement compared to classical methods of fabrication because the layer-by-layer printing allows for very complex object manufacturing that is unachievable with standard tools. Furthermore, AM can induce unknown or unexpected defects. Consequently, we demonstrate terahertz (THz) imaging as an innovative method for 2D inspection of polymer materials. Moreover, THz tomography may be considered as an alternative to x-ray tomography and cheaper 3D imaging for routine control. This paper proposes an experimental study of 3D polymer objects obtained by additive manufacturing techniques. This approach allows us to characterize defects and to control dimensions by volumetric measurements on 3D data reconstructed by tomography.

  4. Solubility Testing of Sucrose Esters of Fatty Acids in International Food Additive Specifications.

    PubMed

    Nagai, Yukino; Kawano, Satoko; Motoda, Kenichiro; Tomida, Masaaki; Tatebe, Chiye; Sato, Kyoko; Akiyama, Hiroshi

    2017-03-01

    We investigated the solubility of 10 samples of sucrose esters of fatty acids (SEFA) products that are commercially available worldwide as food additives (emulsifiers). Although one sample dissolved transparently in both water and ethanol, other samples produced white turbidity and/or precipitates and did not meet the solubility criterion established by the Joint Food and Agriculture Organization of the United Nations (FAO)/WHO Expert Committee on Food Additives (JECFA). When the sample solutions were heated, the solubility in both water and ethanol increased. All of the samples dissolved transparently in ethanol, and dispersed and became white without producing precipitates in water. The present study suggests that the current solubility criterion of the JECFA SEFA specifications needs to be revised.

  5. FUELS IN SOIL TEST KIT: FIELD USE OF DIESEL DOG SOIL TEST KITS

    SciTech Connect

    Unknown

    2001-05-31

    Western Research Institute (WRI) is commercializing Diesel Dog Portable Soil Test Kits for performing analysis of fuel-contaminated soils in the field. The technology consists of a method developed by WRI (U.S. Patents 5,561,065 and 5,976,883) and hardware developed by WRI that allows the method to be performed in the field (patent pending). The method is very simple and does not require the use of highly toxic reagents. The aromatic components in a soil extract are measured by absorption at 254 nm with a field-portable photometer. WRI added significant value to the technology by taking the method through the American Society for Testing and Materials (ASTM) approval and validation processes. The method is designated ASTM Method D-5831-96, Standard Test Method for Screening Fuels in Soils. This ASTM designation allows the method to be used for federal compliance activities. In FY 99, twenty-five preproduction kits were successfully constructed in cooperation with CF Electronics, Inc., of Laramie, Wyoming. The kit components work well and the kits are fully operational. In the calendar year 2000, kits were provided to the following entities who agreed to participate as FY 99 and FY 00 JSR (Jointly Sponsored Research) cosponsors and use the kits as opportunities arose for field site work: Wyoming Department of Environmental Quality (DEQ) (3 units), F.E. Warren Air Force Base, Gradient Corporation, The Johnson Company (2 units), IT Corporation (2 units), TRC Environmental Corporation, Stone Environmental, ENSR, Action Environmental, Laco Associates, Barenco, Brown and Caldwell, Dames and Moore Lebron LLP, Phillips Petroleum, GeoSyntek, and the State of New Mexico. By early 2001, ten kits had been returned to WRI following the six-month evaluation period. On return, the components of all ten kits were fully functional. The kits were upgraded with circuit modifications, new polyethylene foam inserts, and updated instruction manuals.

  6. Interactive responses of grass litter decomposition to warming, nitrogen addition and detritivore access in a temperate old field.

    PubMed

    Moise, Eric R D; Henry, Hugh A L

    2014-12-01

    Plant litter decomposition has been studied extensively in the context of both climate warming and increased atmospheric N deposition. However, much of this research is based on microbial responses, despite the potential for detritivores to contribute substantially to litter breakdown. We measured litter mass-loss responses to the combined effects of warming, N addition and detritivore access in a grass-dominated old field. We concurrently assessed the roles of litter treatment origin vs. microenvironment (direct warming and N-addition effects) to elucidate the mechanisms through which these factors affect decomposition. After 6 weeks, mass loss increased in N-addition plots, and it increased with detritivore access in the absence of warming. After 1 year, warming, N addition, and detritivore access all increased litter mass loss, although the effects of N addition and warming were non-additive in the detritivore-access plots. For the litter-origin experiment, mass loss after 6 weeks increased in litter from N-addition plots and warmed plots, but unlike the overall decomposition response, the N-addition effect was enhanced by detritivore access. Conversely, for the microenvironment experiment, detritivore access only increased mass loss in unfertilized plots. After 1 year, detritivore access increased mass loss in the litter-origin and microenvironment experiments, but there were no warming or N-addition effects. Overall, our results provide support for a substantial role of detritivores in promoting litter mass loss in our system. Moreover, they reveal important interactions between litter origin, microclimate and detritivores in determining decomposition responses to global change.

  7. Neutron measurements of stresses in a test artifact produced by laser-based additive manufacturing

    SciTech Connect

    Gnäupel-Herold, Thomas; Slotwinski, John; Moylan, Shawn

    2014-02-18

    A stainless steel test artifact produced by Direct Metal Laser Sintering and similar to a proposed standardized test artifact was examined using neutron diffraction. The artifact contained a number of structures with different aspect ratios pertaining to wall thickness, height above base plate, and side length. Through spatial resolutions of the order of one millimeter the volumetric distribution of stresses in several was measured. It was found that the stresses peak in the tensile region around 500 MPa near the top surface, with balancing compressive stresses in the interior. The presence of a support structure (a one millimeter high, thin walled, hence weaker, lattice structure deposited on the base plate, followed by a fully dense AM structure) has only minor effects on the stresses.

  8. A Pilot Test of the Additive Benefits of Physical Exercise to CBT for OCD.

    PubMed

    Rector, Neil A; Richter, Margaret A; Lerman, Bethany; Regev, Rotem

    2015-01-01

    The majority of "responders" to first-line cognitive-behavioural therapy (CBT) and pharmacological treatments for obsessive-compulsive disorder (OCD) are left with residual symptoms that are clinically relevant and disabling. Therefore, there is pressing need for widely accessible efficacious alternative and/or adjunctive treatments for OCD. Accumulating evidence suggests that physical exercise may be one such intervention in the mood and anxiety disorders broadly, although we are aware of only two positive small-scale pilot studies that have tested its clinical benefits in OCD. This pilot study aimed to test the feasibility and preliminary efficacy of adding a structured physical exercise programme to CBT for OCD. A standard CBT group was delivered concurrently with a 12-week customized exercise programme to 11 participants. The exercise regimen was individualized for each participant based on peak heart rate measured using an incremental maximal exercise test. Reports of exercise adherence across the 12-week regimen exceeded 80%. A paired-samples t-test indicated very large treatment effects in Yale-Brown Obsessive-Compulsive Scale scores from pre- to post-treatment in CBT group cohorts led by expert CBT OCD specialists (d = 2.55) and junior CBT clinician non-OCD specialists (d = 2.12). These treatment effects are very large and exceed effects typically observed with individual and group-based CBT for OCD based on leading meta-analytic reviews, as well as previously obtained treatment effects for CBT using the same recruitment protocol without exercise. As such, this pilot work demonstrates the feasibility and significant potential clinical utility of a 12-week aerobic exercise programme delivered in conjunction with CBT for OCD.

  9. Additional Value of CH₄ Measurement in a Combined (13)C/H₂ Lactose Malabsorption Breath Test: A Retrospective Analysis.

    PubMed

    Houben, Els; De Preter, Vicky; Billen, Jaak; Van Ranst, Marc; Verbeke, Kristin

    2015-09-07

    The lactose hydrogen breath test is a commonly used, non-invasive method for the detection of lactose malabsorption and is based on an abnormal increase in breath hydrogen (H₂) excretion after an oral dose of lactose. We use a combined (13)C/H₂ lactose breath test that measures breath (13)CO₂ as a measure of lactose digestion in addition to H₂ and that has a better sensitivity and specificity than the standard test. The present retrospective study evaluated the results of 1051 (13)C/H₂ lactose breath tests to assess the impact on the diagnostic accuracy of measuring breath CH₄ in addition to H₂ and (13)CO₂. Based on the (13)C/H₂ breath test, 314 patients were diagnosed with lactase deficiency, 138 with lactose malabsorption or small bowel bacterial overgrowth (SIBO), and 599 with normal lactose digestion. Additional measurement of CH₄ further improved the accuracy of the test as 16% subjects with normal lactose digestion and no H₂-excretion were found to excrete CH₄. These subjects should have been classified as subjects with lactose malabsorption or SIBO. In conclusion, measuring CH₄-concentrations has an added value to the (13)C/H₂ breath test to identify methanogenic subjects with lactose malabsorption or SIBO.

  10. Field Testing GEOICE: A Next-Generation Polar Seismometer

    NASA Astrophysics Data System (ADS)

    Beaudoin, B. C.; Winberry, J. P.; Huerta, A. D.; Chung, P.; Parker, T.; Anderson, K. R.; Bilek, S. L.; Carpenter, P.

    2015-12-01

    We report on the development of a new NSF MRI-community supported seismic observatory designed for studies in ice-covered regions - the Geophysical Earth Observatory for Ice Covered Environs (GEOICE). This project is motivated by the need to densify and optimize the collection of high-quality seismic data relevant to key solid Earth and cryosphere science questions. The GEOICE instruments and their power and other ancillary systems are being designed to require minimal installation time and logistical load (i.e., size and weight), while maximizing ease-of-use in the field. The system is capable of advanced data handling and telemetry while being able to withstand conditions associated with icy environments, including cold/wet conditions and high-latitude solar limitations. The instrument capability will include a hybrid seismograph pool of broadband and intermediate elements for observation of both long-period signals (e.g, long-period surface waves and slow sources) and intermediate-to-short-period signals (e.g., teleseismic body waves, local seismicity, and impulsive or extended glaciogenic signals).Key features will include a design that integrates the seismometer and digitizer into a single, environmentally and mechanically robust housing; very low power requirements (~1 watt) for the intermediate-band systems; and advanced power systems that optimize battery capacity and operational limits. The envisioned ~100 element GEOICE instruments will nearly double the current polar inventory of stations and will be maintained and supported at the IRIS PASSCAL Instrument Center to ensure full and flexible peer-reviewed community use. Prototype instruments are currently deployed in Antarctica and Alaska, with a larger Antarctic deployment planned for the 2015-2016 season. The results of these field tests will help to refine instrumentation design and lead to the production of robust and capable next-generation seismic sensors.

  11. Advanced Rooftop Control (ARC) Retrofit: Field-Test Results

    SciTech Connect

    Wang, Weimin; Katipamula, Srinivas; Ngo, Hung; Underhill, Ronald M.; Taasevigen, Danny J.; Lutes, Robert G.

    2013-07-31

    The multi-year research study was initiated to find solutions to improve packaged equipment operating efficiency in the field. Pacific Northwest National Laboratory (PNNL), with funding from the U.S. Department of Energy’s (DOE’s) Building Technologies Office (BTO) and Bonneville Power Administration (BPA) conducted this research, development and demonstration (RD&D) study. Packaged equipment with constant speed supply fans is designed to provide ventilation at the design rate at all times when the fan is operating as required by building code. Although there are a number of hours during the day when a building may not be fully occupied or the need for ventilation is lower than designed, the ventilation rate cannot be adjusted easily with a constant speed fan. Therefore, modulating the supply fan in conjunction with demand controlled ventilation (DCV) will not only reduce the coil energy but also reduce the fan energy. The objective of this multi-year research, development and demonstration project was to determine the magnitude of energy savings achievable by retrofitting existing packaged rooftop air conditioners with advanced control strategies not ordinarily used for packaged units. First, through detailed simulation analysis, it was shown that significant energy (between 24% and 35%) and cost savings (38%) from fan, cooling and heating energy consumption could be realized when packaged air conditioning units with gas furnaces are retrofitted with advanced control packages (combining multi-speed fan control, integrated economizer controls and DCV). The simulation analysis also showed significant savings for heat pumps (between 20% and 60%). The simulation analysis was followed by an extensive field test of a retrofittable advanced rooftop unit (RTU) controller.

  12. Core-shell column Tanaka characterization and additional tests using active pharmaceutical ingredients.

    PubMed

    Ludvigsson, Jufang Wu; Karlsson, Anders; Kjellberg, Viktor

    2016-12-01

    In the last decade, core-shell particles have gained more and more attention in fast liquid chromatography separations due to their comparable performance with fully porous sub-2 μm particles and their significantly lower back pressure. Core-shell particles are made of a solid core surrounded by a shell of classic fully porous material. To embrace the developed core-shell column market and use these columns in pharmaceutical analytical applications, 17 core-shell C18 columns purchased from various vendors with various dimensions (50 mm × 2.1 mm to 100 mm × 3 mm) and particle sizes (1.6-2.7 μm) were characterized using Tanaka test protocols. Furthermore, four selected active pharmaceutical ingredients were chosen as test probes to investigate the batch to batch reproducibility for core-shell columns of particle size 2.6-2.7 μm, with dimension of 100 × 3 mm and columns of particle size 1.6 μm, with dimension 100 × 2.1 mm under isocratic elution. Columns of particle size 2.6-2.7 μm were also tested under gradient elution conditions. To confirm the claimed comparable efficiency of 2.6 μm core-shell particles as sub-2 μm fully porous particles, column performances of the selected core-shell columns were compared with BEH C18 , 1.7 μm, a fully porous column material as well.

  13. Formalin treatments pass new tests. Additional notes on the control of ecto-parasitic protozoa

    USGS Publications Warehouse

    1940-01-01

    After the completion of the eхреriments reported recently, in which the efficacy of formalin in controlling infections of Gostia mecatrix was demonstrated, the author was afforded an opportunity to test the value of formalin solutions in combatting established mixed infections of (Gyrodactylus, Tricbodina, Cyclochaeta) and a stalked protozoan on rainbow trout fingerlings. This opportunity was provided through the courtesy and cooperation of Clarence F. Pautzke, Chief Biologist for the Washington State Game Department, and Lee Walters, Superintendent of the Washington State Hatchery at Seward Park, Seattle.

  14. Visual field test simulation and error in threshold estimation.

    PubMed Central

    Spenceley, S E; Henson, D B

    1996-01-01

    AIM: To establish, via computer simulation, the effects of patient response variability and staircase starting level upon the accuracy and repeatability of static full threshold visual field tests. METHOD: Patient response variability, defined by the standard deviation of the frequency of seeing versus stimulus intensity curve, is varied from 0.5 to 20 dB (in steps of 0.5 dB) with staircase starting levels ranging from 30 dB below to 30 dB above the patient's threshold (in steps of 10 dB). Fifty two threshold estimates are derived for each condition and the error of each estimate calculated (difference between the true threshold and the threshold estimate derived from the staircase procedure). The mean and standard deviation of the errors are then determined for each condition. The results from a simulated quadrantic defect (response variability set to typical values for a patient with glaucoma) are presented using two different algorithms. The first corresponds with that normally used when performing a full threshold examination while the second uses results from an earlier simulated full threshold examination for the staircase starting values. RESULTS: The mean error in threshold estimates was found to be biased towards the staircase starting level. The extent of the bias was dependent upon patient response variability. The standard deviation of the error increased both with response variability and staircase starting level. With the routinely used full threshold strategy the quadrantic defect was found to have a large mean error in estimated threshold values and an increase in the standard deviation of the error along the edge of the defect. When results from an earlier full threshold test are used as staircase starting values this error and increased standard deviation largely disappeared. CONCLUSION: The staircase procedure widely used in threshold perimetry increased the error and the variability of threshold estimates along the edges of defects. Using

  15. Site Characterization for a Deep Borehole Field Test

    NASA Astrophysics Data System (ADS)

    Kuhlman, K. L.; Hardin, E. L.; Freeze, G. A.; Sassani, D.; Brady, P. V.

    2015-12-01

    The US Department of Energy Office of Nuclear Energy is at the beginning of 5-year Deep Borehole Field Test (DBFT) to investigate the feasibility of constructing and characterizing two boreholes in crystalline basement rock to a depth of 5 km (16,400 ft). The concept of deep borehole disposal for radioactive waste has some advantages over mined repositories, including incremental construction and loading, the enhanced natural barriers provided by deep continental crystalline basement, and reduced site characterization. Site characterization efforts need to determine an eligible site that does not have the following disqualifying characteristics: greater than 2 km to crystalline basement, upward vertical fluid potential gradients, presence of economically exploitable natural resources, presence of high permeability connection to the shallow subsurface, and significant probability of future seismic or volcanic activity. Site characterization activities for the DBFT will include geomechanical (i.e., rock in situ stress state, and fluid pressure), geological (i.e., rock and fracture infill lithology), hydrological (i.e., quantity of fluid, fluid convection properties, and solute transport mechanisms), and geochemical (i.e., rock-water interaction and natural tracers) aspects. Both direct (i.e., sampling and in situ testing) and indirect (i.e., borehole geophysical) methods are planned for efficient and effective characterization of these site aspects and physical processes. Borehole-based characterization will be used to determine the variability of system state (i.e., stress, pressure, temperature, and chemistry) with depth, and interpretation of material and system parameters relevant to numerical site simulation. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE

  16. Field tests of acoustic telemetry for a portable coastal observatory

    USGS Publications Warehouse

    Martini, M.; Butman, B.; Ware, J.; Frye, D.

    2006-01-01

    Long-term field tests of a low-cost acoustic telemetry system were carried out at two sites in Massachusetts Bay. At each site, an acoustic Doppler current profiler mounted on a bottom tripod was fitted with an acoustic modem to transmit data to a surface buoy; electronics mounted on the buoy relayed these data to shore via radio modem. The mooring at one site (24 m water depth) was custom-designed for the telemetry application, with a custom designed small buoy, a flexible electro-mechanical buoy to mooring joint using a molded chain connection to the buoy, quick-release electro-mechanical couplings, and dual hydrophones suspended 7 m above the bottom. The surface buoy at the second site (33 m water depth) was a U.S. Coast Guard (USCG) channel buoy fitted with telemetry electronics and clamps to hold the hydrophones. The telemetry was tested in several configurations for a period of about four years. The custom-designed buoy and mooring provided nearly error-free data transmission through the acoustic link under a variety of oceanographic conditions for 261 days at the 24 m site. The electro mechanical joint, cables and couplings required minimal servicing and were very reliable, lasting 862 days deployed before needing repairs. The acoustic communication results from the USCG buoy were poor, apparently due to the hard cobble bottom, noise from the all-steel buoy, and failure of the hydrophone assembly. Access to the USCG buoy at sea required ideal weather. ??2006 IEEE.

  17. The Savannah River Technology Center environmental monitoring field test platform

    SciTech Connect

    Rossabi, J.

    1993-03-05

    Nearly all industrial facilities have been responsible for introducing synthetic chemicals into the environment. The Savannah River Site is no exception. Several areas at the site have been contaminated by chlorinated volatile organic chemicals. Because of the persistence and refractory nature of these contaminants, a complete clean up of the site will take many years. A major focus of the mission of the Environmental Sciences Section of the Savannah River Technology Center is to develop better, faster, and less expensive methods for characterizing, monitoring, and remediating the subsurface. These new methods can then be applied directly at the Savannah River Site and at other contaminated areas in the United States and throughout the world. The Environmental Sciences Section has hosted field testing of many different monitoring technologies over the past two years primarily as a result of the Integrated Demonstration Program sponsored by the Department of Energy`s Office of Technology Development. This paper provides an overview of some of the technologies that have been demonstrated at the site and briefly discusses the applicability of these techniques.

  18. Field test of a post-closure radiation monitor

    SciTech Connect

    Reed, S.E.; Christy, C.E.; Heath, R.E.

    1995-10-01

    The DOE is conducting remedial actions at many sites contaminated with radioactive materials. After closure of these sites, long-term subsurface monitoring is typically required by law. This monitoring is generally labor intensive and expensive using conventional sampling and analysis techniques. The U.S. Department of Energy`s Morgantown Energy Technology Center (METC) has contracted with Babcock and Wilcox to develop a Long-Term Post-Closure Radiation Monitoring System (LPRMS) to reduce these monitoring costs. The system designed in Phase I of this development program monitors gamma radiation using a subsurface cesium iodide scintillator coupled to above-ground detection electronics using optical waveguide. The radiation probe can be installed to depths up to 50 meters using cone penetrometer techniques, and requires no downhole electrical power. Multiplexing, data logging and analysis are performed at a central location. A prototype LPRMS probe was built, and B&W and FERMCO field tested this monitoring probe at the Fernald Environmental Management Project in the fall of 1994 with funding from the DOE`s Office of Technology Development (EM-50) through METC. The system was used measure soil and water with known uranium contamination levels, both in drums and in situ depths up to 3 meters. For comparison purposes measurements were also performed using a more conventional survey probe with a sodium iodide scintillator directly butt-coupled to detection electronics.

  19. Rigorously testing multialternative decision field theory against random utility models.

    PubMed

    Berkowitsch, Nicolas A J; Scheibehenne, Benjamin; Rieskamp, Jörg

    2014-06-01

    Cognitive models of decision making aim to explain the process underlying observed choices. Here, we test a sequential sampling model of decision making, multialternative decision field theory (MDFT; Roe, Busemeyer, & Townsend, 2001), on empirical grounds and compare it against 2 established random utility models of choice: the probit and the logit model. Using a within-subject experimental design, participants in 2 studies repeatedly choose among sets of options (consumer products) described on several attributes. The results of Study 1 showed that all models predicted participants' choices equally well. In Study 2, in which the choice sets were explicitly designed to distinguish the models, MDFT had an advantage in predicting the observed choices. Study 2 further revealed the occurrence of multiple context effects within single participants, indicating an interdependent evaluation of choice options and correlations between different context effects. In sum, the results indicate that sequential sampling models can provide relevant insights into the cognitive process underlying preferential choices and thus can lead to better choice predictions.

  20. Field test of a wideband downhole EM transmitter

    SciTech Connect

    Becker, Alex; Lee, Ki Ha; Reginato, Lou

    1999-07-01

    A viable large bandwidth TEM transmitter can be constructed using very conventional means although in the present case the effective magnetic permeability of the solenoid core was lower than expected. Only a small number of turns can be used too maintain reasonably low inductance. This has to be compensated with the use of large currents. In this case, good ventilation must be provided to avoid overheating the electronics. In our case the most temperature sensitive element was the optic fiber transmitter which usually failed after about an hour of operation. Care must also be taken to guarantee balance between the negative and positive pulses as this improves the signal/noise ratio. Finally, we reiterate the need to review the origin and nature of the trigger pulse so that consistent properly clocked data can be acquired. In spite of the unlimited nature of the RFS tests which prevented us from acquiring data suitable for a direct demonstration of the wavefield transform, we did secure high quality wideband data that confirmed the proper performance of the prototype transmitter. We are certain that this equipment can now be used in an oil-field environment to acquire data suitable for a practical verification of the wavefield transform.

  1. Implementing the Mars Science Laboratory Terminal Descent Sensor Field Test Campaign

    NASA Technical Reports Server (NTRS)

    Montgomery, Jim

    2012-01-01

    Overall, the MSL TDS Field Test campaign was very successful. TDS was shown to perform extremely well over the required operational envelope. Early BB TDS field tests uncovered a number of issues, but none that invalidated the TDS design or implementation. EM TDS tests uncovered minor things of interest, but nothing of concern. Value of testing hardware in the field was demonstrated and significantly contributed to the overall TDS V&V effort. Over the 5-plus year field test campaign, numerous lessons were learned that will inform future field test efforts.

  2. Direct Field and Reverberant Chamber Acoustic Test Comparisons

    NASA Technical Reports Server (NTRS)

    OConnell, Michael

    2007-01-01

    Reverberant and direct acoustic test comparisons were analyzed in this viewgraph presentation. The acoustic test data set includes: 1) CloudSat antenna subjected to PF reverberant chamber acoustic test; 2) CloudSat subjected to a PF direct speaker acoustic test; and 3) DAWN flight spacecraft subjected to PF direct speaker and a workmanship reverberant chamber acoustic test.

  3. Electronics Manufacturer Provided With Testing and Evaluation Data Necessary to Obtain Additional Orders

    NASA Technical Reports Server (NTRS)

    1998-01-01

    A local electronics manufacturer, the Sterling Manufacturing Company, was presented with the opportunity to supply 30,000 automotive cellular antennas to a European subsidiary of a large U.S. auto manufacturer. Although the company built an antenna that they believed would meet the auto manufacturer's specifications, they were unable to conduct the necessary validation tests in-house. They decided to work with NASA Lewis Research Center's Space Electronics Division, which, as part of its technology development program, evaluates the performance of antennas in its Microwave Systems Lab to assess their capabilities for space communications applications. Data measured in Lewis' Microwave Systems Lab proved that Sterling's antenna performed better than specified by the auto manufacturer.

  4. Additional testing of the inlets designed for a tandem fan V/STOL nacelle

    NASA Technical Reports Server (NTRS)

    Ybarra, A. H.

    1981-01-01

    The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

  5. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false What are the field-testing procedures... § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures...

  6. 40 CFR 35.2211 - Field testing for Innovative and Alternative Technology Report.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Field testing for Innovative and... Treatment Works § 35.2211 Field testing for Innovative and Alternative Technology Report. The grantee shall submit a report containing the procedure, cost, results and conclusions of any field testing. The...

  7. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false What are the field-testing procedures... § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures...

  8. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false What are the field-testing procedures... § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures...

  9. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What are the field-testing procedures... § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures...

  10. 40 CFR 1048.515 - What are the field-testing procedures?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false What are the field-testing procedures... § 1048.515 What are the field-testing procedures? (a) This section describes the procedures to determine whether your engines meet the field-testing emission standards in § 1048.101(c). These procedures...

  11. 40 CFR 35.2211 - Field testing for Innovative and Alternative Technology Report.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Field testing for Innovative and... Treatment Works § 35.2211 Field testing for Innovative and Alternative Technology Report. The grantee shall submit a report containing the procedure, cost, results and conclusions of any field testing. The...

  12. 40 CFR 270.63 - Permits for land treatment demonstrations using field test or laboratory analyses.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the field test or laboratory analyses, or as a two-phase facility permit covering the field tests, or... laboratory analyses. (b) If the Director finds that a phased permit may be issued, he will establish, as requirements in the first phase of the facility permit, conditions for conducting the field tests or...

  13. 40 CFR 270.63 - Permits for land treatment demonstrations using field test or laboratory analyses.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... the field test or laboratory analyses, or as a two-phase facility permit covering the field tests, or... laboratory analyses. (b) If the Director finds that a phased permit may be issued, he will establish, as requirements in the first phase of the facility permit, conditions for conducting the field tests or...

  14. 40 CFR 270.63 - Permits for land treatment demonstrations using field test or laboratory analyses.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... the field test or laboratory analyses, or as a two-phase facility permit covering the field tests, or... laboratory analyses. (b) If the Director finds that a phased permit may be issued, he will establish, as requirements in the first phase of the facility permit, conditions for conducting the field tests or...

  15. 40 CFR 270.63 - Permits for land treatment demonstrations using field test or laboratory analyses.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... the field test or laboratory analyses, or as a two-phase facility permit covering the field tests, or... laboratory analyses. (b) If the Director finds that a phased permit may be issued, he will establish, as requirements in the first phase of the facility permit, conditions for conducting the field tests or...

  16. 40 CFR 270.63 - Permits for land treatment demonstrations using field test or laboratory analyses.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... conducting such tests or analyses. The owner or operator must also submit all data collected during the field... demonstrations using field test or laboratory analyses. 270.63 Section 270.63 Protection of Environment... using field test or laboratory analyses. (a) For the purpose of allowing an owner or operator to...

  17. Influence of compost addition on lead and arsenic bioavailability in reclaimed orchard soil assessed using Porcellio scaber bioaccumulation test.

    PubMed

    Udovic, M; McBride, M B

    2012-02-29

    Long-term application of lead arsenate in orchards has led to a significant accumulation of Pb and As in the topsoil. Reclamation of old orchards for agricultural purposes entails the exposure of humans to Pb and As, which can be reduced by adequate remediation actions. In this study, we assessed the remediation efficiency of compost addition, commonly used as a sustainable agricultural practice, in decreasing the human exposure Pb and As by direct ingestion. The remediation was evaluated based on Pb and As bioavailability, assessed by means of a selective non-exhaustive chemical extraction (modified Morgan extraction, MME), with a physiologically based extraction test (PBET) for the assessment of Pb and As bioavailability in ingested soils and with a novel in vivo bioaccumulation test with isopods (Porcellio scaber). All the tests showed that compost addition consistently reduced Pb, but increased As potential bioavailability. The bioaccumulation test with P. scaber was sensitive to changes in Pb and As bioavailability in test soils. However, the results indicate that the bioavailability of As could be under- or overestimated using solely chemical extraction tests. Indirect assessment of trace metal bioavailability with bioaccumulation in isopods can be used as complementary source of data to the existing in vitro chemical extraction test approach for the estimation of human exposure to trace elements in polluted and remediated soil. This is the first report on the use of As accumulation in P. scaber as a tool for the assessment of As bioavailability in contaminated orchard soil.

  18. Test Mass Temperature Field and Laser Aberration Modeling in Advanced LIGO

    NASA Astrophysics Data System (ADS)

    Ramette, Joshua; Kasprzack, Marie; Gonzalez, Gabriela; Brooks, Aidan; Blair, Carl; Kandhasamy, Shivaraj; Wang, Haoyu; LIGO Collaboration

    2017-01-01

    Advanced LIGO uses high laser power in the main interferometer arm cavities to achieve design sensitivity. A small part of this power is absorbed in the interferometer cavity mirrors where it creates thermal lenses. Actuation by ``ring heaters,'' additional heater elements aimed to reduce the temperature gradients in the mirrors, minimizes aberrations in the main laser beam due to thermal lensing. We derive the first analytical model of the temperature field contribution in the mirrors generated by an ideal ring heater. In addition, we simulate the test mass temperature field using finite element analysis software and find agreement with the prediction of our ring heater analytical model and existing models for self-heating of the test mass by the main laser beam. From our ring heater temperature field models, we then express the resulting optical aberration contribution in the main laser and compare to Hartmann wavefront sensor measurements of the aberration. Used in conjunction with wavefront measurements, our model provides a more complete understanding of the thermal state of the cavity mirrors and will allow a more efficient use of the ring heaters in Advanced LIGO. We thank the National Science Foundation for supporting this work (NSF grant #1262890 and #1205882).

  19. Semi-empirical equation of limiting current for cobalt electrodeposition in the presence of magnetic field and additive electrolyte

    NASA Astrophysics Data System (ADS)

    Sudibyo, Aziz, N.

    2016-02-01

    One of the available methods to solve a roughening in cobalt electrodeposition is magneto electrodeposition (MED) in the presence of additive electrolyte. Semi-empirical equation of limiting current under a magnetic field for cobalt MED in the presence of boric acid as an additive electrolyte was successfully developed. This semi empirical equation shows the effects of the electrode area (A), the concentration of the electro active species (C), the diffusion coefficient of the electro active species (D), the kinematic viscosity of the electrolyte (v), magnetic strength (B) and the number of electrons involved in the redox process (n). The presence of boric acid led to decrease in the limiting current, but the acid was found useful as a buffer to avoid the local pH rise caused by parallel hydrogen evolution reaction (HER).

  20. Laboratory endurance testing of a 25/75 sunflower oil-diesel fuel blend treated with fuel additives

    SciTech Connect

    Ziejewski, M.; Kaufman, K.R.; Tupa, R.C.

    1984-02-01

    The engine performance and durability effects of a barium smoke suppressant additive, Lubrizol 565, and an ashless polymeric additive, Lubrizol 552, in a 25-75 blend (v/v) of alkali refined sunflower oil with diesel fuel were investigated. The study was performed on a direct injected, turbocharged, and intercooled diesel engine. These additives were tested in an attempt to reduce carbon buildup problems observed while using an untreated 25-75 blend of sunflower oil and diesel fuel. Compared to the engine tests on the untreated 25-75 mixture, the barium smoke suppressant additive proved effective in cleaning the inside of injection nozzles (no needle sticking, no carbon build-up inside the orifices), reducing diesel exhaust smoke, and increasing engine power output. However, there was increased residue accumulation in the combustion chamber and on the exterior of the injection nozzle tips. The ashless dispersant additive also improved nozzle cleanliness but did not demonstrate any effect on engine power or cause excessive carbon buildup on the nozzle tips, top of the pistons, and cylinder head. The Lubrizol 552 dispersant looks very promising as an additive for vegetable oil diesel fuel blends for controlling excessive carbon and lacquer deposits.

  1. Smart Infrared Inspection System Field Operational Test Final Report

    SciTech Connect

    Siekmann, Adam; Capps, Gary J; Franzese, Oscar; Lascurain, Mary Beth

    2011-06-01

    The Smart InfraRed Inspection System (SIRIS) is a tool designed to assist inspectors in determining which vehicles passing through the SIRIS system are in need of further inspection by measuring the thermal data from the wheel components. As a vehicle enters the system, infrared cameras on the road measure temperatures of the brakes, tires, and wheel bearings on both wheel ends of commercial motor vehicles (CMVs) in motion. This thermal data is then presented to enforcement personal inside of the inspection station on a user friendly interface. Vehicles that are suspected to have a violation are automatically alerted to the enforcement staff. The main goal of the SIRIS field operational test (FOT) was to collect data to evaluate the performance of the prototype system and determine the viability of such a system being used for commercial motor vehicle enforcement. From March 2010 to September 2010, ORNL facilitated the SIRIS FOT at the Greene County Inspection Station (IS) in Greeneville, Tennessee. During the course of the FOT, 413 CMVs were given a North American Standard (NAS) Level-1 inspection. Of those 413 CMVs, 384 were subjected to a SIRIS screening. A total of 36 (9.38%) of the vehicles were flagged by SIRIS as having one or more thermal issues; with brakes issues making up 33 (91.67%) of those. Of the 36 vehicles flagged as having thermal issues, 31 (86.11%) were found to have a violation and 30 (83.33%) of those vehicles were placed out-of-service (OOS). Overall the enforcement personnel who have used SIRIS for screening purposes have had positive feedback on the potential of SIRIS. With improvements in detection algorithms and stability, the system will be beneficial to the CMV enforcement community and increase overall trooper productivity by accurately identifying a higher percentage of CMVs to be placed OOS with minimal error. No future evaluation of SIRIS has been deemed necessary and specifications for a production system will soon be drafted.

  2. Field test for mechanical efficiency evaluation in matching volleyball players.

    PubMed

    Laconi, P; Melis, F; Crisafulli, A; Sollai, R; Lai, C; Concu, A

    1998-01-01

    Field tests were performed in 10 volleyball (VB) players (4 females and 6 males) in order to obtain an index of mechanical work efficiency (mu' = Wmec/Woxy) while athletes played a game. Wmec was the mechanical work output, obtained by means of home made video image analysis software, by summing potential, kinetic translational and kinetic rotational energies of running and jumping athletes. Woxy was the oxidative energy consumption obtained from O2 consumption (VO2) by a telemetry device (Cosmed K2) that also gave values of pulmonary ventilation (VE) and heart rate (HR). VB were studied at rest before a game (R), during attacking phases (A) and during defensive phases (D). At R were found: VE = 11 +/- 1 l x min(-1), HR = 78 +/- 7b x min(-1), VO2 = 3.71 +/- 1.1 ml x kg(-1) x min(-1), Woxy = 75.1 +/- 22.3 J x kg(-1) x min(-1). During A all variables increased: VE = 49 +/- 6l x min(-1), HR = 149 +/- 15 b x min(-1), VO2 = 23.1 +/- 3.3ml x kg(-1) x min(-1), Woxy = 482.8 +/- 69.0 J x kg(-1) x min(-1), and Wmec 275.5 +/- 57.0 J x kg(-1) x min(-1) with mu'=0.57 +/- 0.09. In D HR (-9%), VE, VO2 and Woxy (-18%) were reduced when compared to A, decreasing mu' to 0.21 +/- 0.05. On the other hand mu' was found higher than 0.25 during A indicating an anaerobic contribution to energy expenditure; in D the mu' lower than 0.25 indicated a restoration of anaerobic energy sources. It might be proposed that a greater difference in mu' values between A and D also means a higher anaerobic energy contribution to the volleyball game.

  3. A field test and comparison of acute and chronic sediment toxicity tests with the estuarine amphipod Leptocheirus plumulosus in Chesapeake Bay, USA.

    PubMed

    McGee, Beth L; Fisher, Daniel J; Wright, David A; Yonkos, Lance T; Ziegler, Gregory P; Turley, Steven D; Farrar, J Daniel; Moore, David W; Bridges, Todd S

    2004-07-01

    A 28-d partial life-cycle test with the estuarine amphipod Leptocheirus plumulosus was developed in response to the need for an assay to mimic chronic exposure to sediment-associated contaminants. To ensure that toxicity tests have environmental relevance, it is essential to evaluate the relationship between laboratory responses and field measures of contamination. Consequently, one objective of the study was to compare the results of the chronic sediment toxicity test with L. plumulosus to gradients of sediment contamination and the in situ benthic community in its native Chesapeake Bay. Chronic tests were conducted by two laboratories, the Army Corps of Engineers Waterways Experiment Station ([WES]; Vicksburg, MS, USA) and the University of Maryland ([UM] College Park, MD, USA) using different feeding regimes, providing the opportunity to evaluate the effect of this variable on response sensitivity. A second objective was to compare the relative sensitivity of acute and chronic tests with L. plumulosus with field-collected sediments. Overall, there was good agreement between the toxicological response of acute and chronic tests with L. plumulosus and field measures of contamination. Survival in the acute test and chronic test conducted by WES was negatively correlated with concentrations of sediment-associated contaminants. Survival in acute exposures was significantly reduced in sediments from 8 of 11 stations. Indigenous L. plumulosus were found only at two of the three stations that did not exhibit acute toxicity. An unexpected finding was the difference in responsiveness of the two chronic tests. Survival in tests conducted by UM and WES was significantly reduced in sediments from 4 and 6 of 11 stations, respectively. No additional sublethal toxicity was detected in the UM chronic test, but the WES test detected reproductive effects at two additional stations. We believe the observed differences were related to the test diet used. Partly as a result of our

  4. MAGNET ENGINEERING AND TEST RESULTS OF THE HIGH FIELD MAGNET R AND D PROGRAM AT BNL.

    SciTech Connect

    COZZOLINO,J.; ANERELLA,M.; ESCALLIER,J.; GANETIS,G.; GHOSH,A.; GUPTA,R.; HARRISON,M.; JAIN,A.; MARONE,A.; MURATORE,J.; PARKER,B.; SAMPSON,W.; SOIKA,R.; WANDERER,P.

    2002-08-04

    The Superconducting Magnet Division at Brookhaven National Laboratory (BNL) has been carrying out design, engineering, and technology development of high performance magnets for future accelerators. High Temperature Superconductors (HTS) play a major role in the BNL vision of a few high performance interaction region (IR) magnets that would be placed in a machine about ten years from now. This paper presents the engineering design of a ''react and wind'' Nb{sub 3}Sn magnet that will provide a 12 Tesla background field on HTS coils. In addition, the coil production tooling as well as the most recent 10-turn R&D coil test results will be discussed.

  5. Methods for testing theory and evaluating impact in randomized field trials

    PubMed Central

    Brown, C. Hendricks; Wang, Wei; Kellam, Sheppard G.; Muthén, Bengt O.; Petras, Hanno; Toyinbo, Peter; Poduska, Jeanne; Ialongo, Nicholas; Wyman, Peter A.; Chamberlain, Patricia; Sloboda, Zili; MacKinnon, David P.; Windham, Amy

    2008-01-01

    Randomized field trials provide unique opportunities to examine the effectiveness of an intervention in real world settings and to test and extend both theory of etiology and theory of intervention. These trials are designed not only to test for overall intervention impact but also to examine how impact varies as a function of individual level characteristics, context, and across time. Examination of such variation in impact requires analytical methods that take into account the trial’s multiple nested structure and the evolving changes in outcomes over time. The models that we describe here merge multilevel modeling with growth modeling, allowing for variation in impact to be represented through discrete mixtures—growth mixture models—and nonparametric smooth functions—generalized additive mixed models. These methods are part of an emerging class of multilevel growth mixture models, and we illustrate these with models that examine overall impact and variation in impact. In this paper, we define intent-to-treat analyses in group-randomized multilevel field trials and discuss appropriate ways to identify, examine, and test for variation in impact without inflating the Type I error rate. We describe how to make causal inferences more robust to misspecification of covariates in such analyses and how to summarize and present these interactive intervention effects clearly. Practical strategies for reducing model complexity, checking model fit, and handling missing data are discussed using six randomized field trials to show how these methods may be used across trials randomized at different levels. PMID:18215473

  6. [Test Reviews in Child Psychology: Test Users Wish to Obtain Practical Information Relevant to their Respective Field of Work].

    PubMed

    Renner, Gerolf; Irblich, Dieter

    2016-11-01

    Test Reviews in Child Psychology: Test Users Wish to Obtain Practical Information Relevant to their Respective Field of Work This study investigated to what extent diagnosticians use reviews of psychometric tests for children and adolescents, how they evaluate their quality, and what they expect concerning content. Test users (n = 323) from different areas of work (notably social pediatrics, early intervention, special education, speech and language therapy) rated test reviews as one of the most important sources of information. Readers of test reviews value practically oriented descriptions and evaluations of tests that are relevant to their respective field of work. They expect independent reviews that critically discuss opportunities and limits of the tests under scrutiny. The results show that authors of test reviews should not only have a background in test theory but should also be familiar with the practical application of tests in various settings.

  7. A conservative method of testing whether combination analgesics produce additive or synergistic effects using evidence from acute pain and migraine.

    PubMed

    Moore, R A; Derry, C J; Derry, S; Straube, S; McQuay, H J

    2012-04-01

    Fixed-dose combination analgesics are used widely, and available both on prescription and over-the-counter. Combination drugs should provide more analgesia than with any single drug in the combination, but there is no evidence in humans about whether oral combinations have just additive effects, or are synergistic or even subadditive. We suggest that the measured result for the combination would be the summation of the absolute benefit increase (effect of active drug minus effect of placebo) of each component of a combination if effects were (merely) additive, and greater than the sum of the absolute benefits if they were synergistic. We tested measured effects of combination analgesics against the sum of the absolute benefits in acute pain and migraine using meta-analysis where individual components and combinations were tested against placebo in the same trials, and verified the result with meta-analyses where individual components and combinations were tested against placebo in different trials. Results showed that expected numbers needed to treat (NNT) for additive effects were generally within the 95% confidence interval of measured NNTs. This was true for combinations of paracetamol plus ibuprofen and paracetamol plus opioids in acute pain, and naproxen plus sumatriptan in migraine, but not where efficacy was very low or very high, nor combinations of paracetamol plus dextropropoxyphene. There was no evidence of synergy, defined as supra-additive effects.

  8. Testing Wetland Delineation Indicators in New England Boulder Fields

    DTIC Science & Technology

    2012-06-01

    groundwater seeps around the boulders into Moose - head Lake. Unlike the Saddleback boulder field, the Burnt Jacket boulder field lacks a clearly defined...September. At Moose - head, the precipitation was normal for June and July and above normal in May, August, and September. The above-normal values in

  9. Comparison Between 30-15 Intermittent Fitness Test and Multistage Field Test on Physiological Responses in Wheelchair Basketball Players

    PubMed Central

    Weissland, Thierry; Faupin, Arnaud; Borel, Benoit; Leprêtre, Pierre-Marie

    2015-01-01

    The intermittent nature of wheelchair court sports suggests using a similar protocol to assess repeated shuttles and recovery abilities. This study aimed to compare performances, physiological responses and perceived rating exertion obtained from the continuous multistage field test (MFT) and the 30-15 intermittent field test (30-15IFT). Eighteen trained wheelchair basketball players (WBP) (WBP: 32.0 ± 5.7 y, IWBF classification: 2.9 ± 1.1 points) performed both incremental field tests in randomized order. Time to exhaustion, maximal rolling velocity (MRV), VO2peak and the peak values of minute ventilation (VEpeak), respiratory frequency (RF) and heart rate (HRpeak) were measured throughout both tests; peak and net blood lactate (Δ[Lact−] = peak–rest values) and perceived rating exertion (RPE) values at the end of each exercise. No significant difference in VO2peak, VEpeak, and RF was found between both tests. 30-15IFT was shorter (12.4 ± 2.4 vs. 14.9 ± 5.1 min, P < 0.05) but induced higher values of MRV and Δ[Lact−] compared to MFT (14.2 ± 1.8 vs. 11.1 ± 1.9 km·h−1 and 8.3 ± 4.2 vs. 6.9 ± 3.3 mmol·L−1, P < 0.05). However, HRpeak and RPE values were higher during MFT than 30-15IFT(172.8 ± 14.0 vs. 166.8 ± 13.8 bpm and 15.3 ± 3.8 vs.13.8 ± 3.5, respectively, P < 0.05). The intermittent shuttles intercepted with rest period occurred during the 30-15IFT could explain a greater anaerobic solicitation. The higher HR and overall RPE values measured at the end of MFT could be explained by its longer duration and a continuous load stress compared to 30-15IFT. In conclusion, 30-15IFT has some advantages over MFT for assess in addition physical fitness and technical performance in WBP. PMID:26733875

  10. Ultraviolet and pulsed electric field treatments have additive effect on inactivation of E. coli in apple juice.

    PubMed

    Gachovska, T K; Kumar, S; Thippareddi, H; Subbiah, J; Williams, F

    2008-11-01

    Apple juice inoculated with Escherichia coli ATCC 23472 was processed continuously using either ultraviolet (UV), high-voltage pulsed electric field (PEF), or a combination of the PEF and UV treatment systems. Apple juice was pumped through either of the systems at 3 flow rates (8, 14, and 20 mL/min). E. coli was reduced by 3.46 log CFU/mL when exposed in a 50 cm length of UV treatment chamber at 8 mL/min (2.94 s treatment time with a product temperature increase of 13 degrees C). E. coli inactivation of 4.87 log CFU/mL was achieved with a peak electric field strength of 60 kV/cm and 11.3 pulses (average pulse width of 3.5 mus, product temperature increased to 52 degrees C). E. coli reductions resulting from a combination treatment of UV and PEF applied sequentially were evaluated. A maximum E. coli reduction of 5.35 log CFU/mL was achieved using PEF (electrical field strength of 60 kV/cm, specific energy of 162 J/mL, and 11.3 pulses) and UV treatments (length of 50 cm, treatment time of 2.94 s, and flow rate of 8 mL/min). An additive effect was observed for the combination treatments (PEF and UV), regardless of the order of treatment (P > 0.05). E. coli reductions of 5.35 and 5.30 log CFU/mL with PEF treatment (electrical field strength of 60 kV/cm, specific energy of 162 J/mL, and 11.3 pulses) followed by UV (length of 30 cm, treatment time of 1.8 s, and flow rate of 8 mL/min) and UV treatment followed by PEF (same treatment conditions), respectively. No synergistic effect was observed.

  11. Anaerobic threshold in children: determination from saliva analysis in field tests.

    PubMed

    Chicharro, J L; Calvo, F; Alvarez, J; Vaquero, A F; Bandrés, F; Legido, J C

    1995-01-01

    The purpose of this study was to determine the anaerobic threshold of children by the analysis of saliva collected during field tests. A group of 25 children (mean age, 10.5 years) performed an incremental exercise test on a track, consisting of 4-min stages at increasing running velocities. Before each test (at rest) and at the end of each stage, both blood (via finger pricks) and saliva samples (for measurement of salivary concentrations of Na+ and Cl-) were collected to determine lactate threshold (Thla-) and saliva threshold (Thsa), respectively. There were no significant differences between values of Thla- and Thsa when expressed either as running velocity [mean Thla-, 10.73 (SD 1.96) km.h-1; mean Thsa, 10.89 (SD 1.69) km.h-1)] or heart rate [Thla-, 182(SD 14) beats. min-1 Thsa 183 (SD 11) beats.min-1]. In addition, correlations between Thsa and Thla were high, when both values were expressed as running velocity in kilometres per hour (r = 0.89; P < 0.001), or heart rate in beats per minute (r = 0.90; p < 0.001). In conclusion, these findings suggested that saliva analysis would be a valid method for anaerobic threshold determination in field tests.

  12. Simple and integrated detours: field tests with Columbian ground squirrels.

    PubMed

    Nesterova, Anna Pavlovna; Hansen, Frank

    2009-09-01

    An internal representation of space offers flexibility to animals during orientation and allows execution of short cuts and detours. We tested the ability of 19 free-ranging Columbian ground squirrels (Spermophilus columbianus) to perform integrated detours that required travelling under- and aboveground. Squirrels were individually tested on their territories (2 tests) and in an arena (7 tests). During tests, animals could reach food by running aboveground and then through tunnels. For the territory tests, natural tunnels were available. For the arena tests, animals used artificial tunnels within a fenced-in part of the meadow. For the last arena test, tubes were placed aboveground replicating the underground structure. In this test animals were asked to make a simple detour, when the full path to the goal was visible. On their territories, 41% of squirrels performed detours. All animals reached the food in the arena. When choosing an arena detour, squirrels based their decision on the proximity of the burrow as well as on whether it led to food. On the last arena test, more squirrels performed correct detours on the first attempt compared to other tests. The results suggest that ground squirrels can perform simple and integrated detours, but animals perform better if the full path is visible.

  13. BOBCAT Personal Radiation Detector Field Test and Evaluation Campaign

    SciTech Connect

    Chris Hodge

    2008-03-01

    Following the success of the Anole test of portable detection system, the U.S. Department of Homeland Security (DHS) Domestic Nuclear Detection Office organized a test and evaluation campaign for personal radiation detectors (PRDs), also known as “Pagers.” This test, “Bobcat,” was conducted from July 17 to August 8, 2006, at the Nevada Test Site. The Bobcat test was designed to evaluate the performance of PRDs under various operational scenarios, such as pedestrian surveying, mobile surveying, cargo container screening, and pedestrian chokepoint monitoring. Under these testing scenarios, many operational characteristics of the PRDs, such as gamma and neutron sensitivities, positive detection and false alarm rates, response delay times, minimum detectable activities, and source localization errors, were analyzed. This paper will present the design, execution, and methodologies used to test this equipment for the DHS.

  14. Personal Radiation Detector Field Test and Evaluation Campaign

    SciTech Connect

    Chris A. Hodge, Ding Yuan, Raymond P. Keegan, Michael A. Krstich

    2007-07-09

    Following the success of the Anole test of portable detection system, the U.S. Department of Homeland Security (DHS) Domestic Nuclear Detection Office organized a test and evaluation campaign for personal radiation detectors (PRDs), also known as 'Pagers'. This test, 'Bobcat', was conducted from July 17 to August 8, 2006, at the Nevada Test Site. The Bobcat test was designed to evaluate the performance of PRDs under various operational scenarios, such as pedestrian surveying, mobile surveying, cargo container screening, and pedestrian chokepoint monitoring. Under these testing scenarios, many operational characteristics of the PRDs, such as gamma and neutron sensitivities, positive detection and false alarm rates, response delay times, minimum detectable activities, and source localization errors, were analyzed. This paper will present the design, execution, and methodologies used to test this equipment for the DHS.

  15. 40 CFR 53.58 - Operational field precision and blank test.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Operational field precision and blank... Methods for PM 2.5 or PM 10-2,5 § 53.58 Operational field precision and blank test. (a) Overview. This... days of field operation, using three collocated test samplers. Measurements of PM are made at a...

  16. Field Testing of Energy-Efficient Flood-Damage-Resistant Residential Envelope Systems Summary Report

    SciTech Connect

    Aglan, H.

    2005-08-04

    The primary purpose of the project was to identify materials and methods that will make the envelope of a house flood damage resistant. Flood damage resistant materials and systems are intended to be used to repair houses subsequent to flooding. This project was also intended to develop methods of restoring the envelopes of houses that have been flooded but are repairable and may be subject to future flooding. Then if the house floods again, damage will not be as extensive as in previous flood events and restoration costs and efforts will be minimized. The purpose of the first pair of field tests was to establish a baseline for typical current residential construction practice. The first test modules used materials and systems that were commonly found in residential envelopes throughout the U.S. The purpose of the second pair of field tests was to begin evaluating potential residential envelope materials and systems that were projected to be more flood-damage resistant and restorable than the conventional materials and systems tested in the first pair of tests. The purpose of testing the third slab-on-grade module was to attempt to dry flood proof the module (no floodwater within the structure). If the module could be sealed well enough to prevent water from entering, then this would be an effective method of making the interior materials and systems flood damage resistant. The third crawl space module was tested in the same manner as the previous modules and provided an opportunity to do flood tests of additional residential materials and systems. Another purpose of the project was to develop the methodology to collect representative, measured, reproducible (i.e. scientific) data on how various residential materials and systems respond to flooding conditions so that future recommendations for repairing flood damaged houses could be based on scientific data. An additional benefit of collecting this data is that it will be used in the development of a standard test

  17. Pressure transient testing at Cerro Prieto Geothermal Field

    SciTech Connect

    Rivera, J.R.; Samaniego, F.V.; Schroeder, R.C.

    1980-01-01

    Because of the inherent problems in applying pressure build-up tests to wells producing two-phase fluids, it was decided to use variable flow tests of short duration known as two-rates tests. In these tests of variation in the well flow rates can be used to intepret the transient pressure response in order to determine reservoir parameters such as permeability, well-bore damage and mean reservoir pressure in the well drainage area. Some examples will illustrate the application of this technique. 11 refs.

  18. Radiative corrections to the Higgs boson couplings in the model with an additional real singlet scalar field

    NASA Astrophysics Data System (ADS)

    Kanemura, Shinya; Kikuchi, Mariko; Yagyu, Kei

    2016-06-01

    We calculate renormalized Higgs boson couplings with gauge bosons and fermions at the one-loop level in the model with an additional isospin singlet real scalar field. These coupling constants can deviate from the predictions in the standard model due to tree-level mixing effects and one-loop contributions of the extra neutral scalar boson. We investigate how they can be significant under the theoretical constraints from perturbative unitarity and vacuum stability and also the condition of avoiding the wrong vacuum. Furthermore, comparing with the predictions in the Type I two Higgs doublet model, we numerically demonstrate how the singlet extension model can be distinguished and identified by using precision measurements of the Higgs boson couplings at future collider experiments.

  19. Friability of spray-applied fireproofing and thermal insulations: field evaluation of prototype test devices

    SciTech Connect

    Rossiter, W.J.; Roberts, W.E.; Mathey, R.G.

    1989-03-01

    The report describes results of the third and final phase of a study conducted for the General Services Administration (GSA) to develop a field-test method to measure the friability of spray-applied fireproofing and thermal-insulation materials. Field tests were conducted on 17 fibrous and 2 cementitious spray-applied materials to assess surface and bulk compression/shear, indentation, abrasion, and impact properties. The tests were performed using prototype devices developed in an earlier phase of the study. As expected, the field specimens displayed varying response to dislodgment or indentation in the tests. The field tests confirmed that the goal of the study had been achieved.

  20. Field test and evaluation of the passive neutron coincidence collar for prototype fast reactor fuel subassemblies

    SciTech Connect

    Menlove, H.O.; Keddar, A.

    1982-08-01

    The passive neutron Coincidence Collar, which was developed for the verification of plutonium content in fast reactor fuel subassemblies, has been field tested using Prototype Fast Reactor fuel. For passive applications, the system measures the /sup 240/Pu-effective mass from the spontaneous fission rate, and in addition, a self-interrogation technique is used to determine the fissile content in the subassembly. Both the passive and active modes were evaluated at the Windscale Works in the United Kingdom. The results of the tests gave a standard deviation 0.75% for the passive count and 3 to 7% for the active measurement for a 1000-s counting time. The unit will be used in the future for the verification of plutonium in fresh fuel assemblies.

  1. A A field test for extremity dose assessment during outages at Korean nuclear power plants.

    PubMed

    Kim, Hee Geun; Kong, Tae Young

    2013-05-01

    During maintenance on the water chamber of a steam generator, the pressuriser heater and the pressure tube feeder in nuclear power plants, workers are likely to receive high radiation doses due to the severe workplace conditions. In particular, it is expected that workers' hands would receive the highest radiation doses because of their contact with the radioactive materials. In this study, field tests for extremity dose assessments in radiation workers undertaking contact tasks with high radiation doses were conducted during outages at pressurised water reactors and pressurised heavy water reactors in Korea. In the test, the radiation workers were required to wear additional thermoluminescent dosemeters (TLDs) on their backs and wrists and an extremity dosemeter on the finger, as well as a main TLD on the chest while performing the maintenance tasks.

  2. Field test of a center pivot irrigation system

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Uniformity of water distribution of a variable rate center pivot irrigation system was evaluated. This 4-span center pivot system was configured with 10 water application zones along its 233 m-long lateral. Two experiments were conducted for the uniformity tests. In one test, a constant water applic...

  3. A Field Test for Upper Body Strength and Endurance.

    ERIC Educational Resources Information Center

    Nelson, Jack K.; And Others

    1991-01-01

    Researchers studied the reliability of the modified push-up test in measuring upper body strength and endurance in elementary through college students. It also examined the accuracy of partner scoring. The test proved much easier to administer than the regular floor push-up. It was valid and reliable for all students and suitable for partner…

  4. The Loughborough Intermittent Shuttle Test: a field test that simulates the activity pattern of soccer.

    PubMed

    Nicholas, C W; Nuttall, F E; Williams, C

    2000-02-01

    The aims of this study were to describe and determine the test-retest reliability of an exercise protocol, the Loughborough Intermittent Shuttle Test (the LIST), which was designed to simulate the activity pattern characteristic of the game of soccer. The protocol consisted of two parts: Part A comprised a fixed period of variable-intensity shuttle running over 20 m; Part B consisted of continuous running, alternating every 20 m between 55% and 95% VO2max, until volitional fatigue. Seven trained games players (age 21.5+/-0.9 years, height 182+/-2 cm, body mass 80.1+/-3.6 kg, VO2max 59.0+/-1.9 ml x kg(-1) x min(-1); mean +/- s(x)) performed the test on two occasions (Trial 1 and Trial 2), at least 7 days apart, to determine the test-retest reliability of the sprint times and running capacity. The physiological and metabolic responses on both occasions were also monitored. The participants ingested water ad libitum during the first trial, and were then prescribed the same amount of water during the second trial. The 15 m sprint times during Trials 1 and 2 averaged 2.42+/-0.04 s and 2.43+/-0.04 s, respectively. Run time during Part B was 6.3+/-2.0 min for Trial 1 and 6.1+/-1.3 min for Trial 2. The 95% limits of agreement for sprint times and run times during Part B were -0.14 to 0.12 s and -3.19 to 2.16 min respectively. There were no differences between trials for heart rate, rating of perceived exertion, body mass change during exercise, or blood lactate and glucose concentrations during the test. Thus, we conclude that the sprint times and the Part B run times were reproducible within the limits previously stated. In addition, the activity pattern and the physiological and metabolic responses closely simulated the match demands of soccer.

  5. Field Testing of High Current Electrokinetic Nanoparticle Treatment for Corrosion Mitigation in Reinforced Concrete

    NASA Technical Reports Server (NTRS)

    Cardenas, Henry; Alexander, Joshua; Kupwade-Patil, Kunal; Calle, Luz marina

    2010-01-01

    Electrokinetic Nanoparticle (EN) treatment was used as a rapid repair measure to mitigate chloride induced corrosion of reinforced concrete in the field. EN treatment uses an electric field to transport positively charged nanoparticles to the reinforcement through the concrete capillary pores. Cylindrical reinforced concrete specimens were batched with 4.5 wt % salt content (based on cement mass). Three distinct electrokinetic treatments were conducted using high current density (up to 5 A/m2) to form a chloride penetration barrier that was established in 5 days, as opposed to the traditional 6-8 weeks, generally required for electrochemical chloride extraction (ECE). These treatments included basic EN treatment, EN with additional calcium treatment, and basic ECE treatment. Field exposures were conducted at the NASA Beachside Corrosion Test Site, Kennedy Space Center, Florida, USA. The specimens were subjected to sea water immersion at the test site as a posttreatment exposure. Following a 30-day post-treatment exposure period, the specimens were subjected to indirect tensile testing to evaluate treatment impact. The EN treated specimens exhibited 60% and 30% increases in tensile strength as compared to the untreated controls and ECE treated specimens respectively. The surfaces of the reinforcement bars of the control specimens were 67% covered by corrosion products. In contrast, the EN treated specimens exhibited corrosion coverage of only 4%. Scanning electron microscopy (SEM) revealed a dense concrete microstructure adjacent to the bars of the treated specimens as compared to the control and ECE specimens. Energy dispersive spectroscopic (EDS) analysis of the polished EN treated specimens showed a reduction in chloride content by a factor of 20 adjacent to the bars. This study demonstrated that EN treatment was successful in forming a chloride penetration barrier rapidly. This work also showed that the chloride barrier was effective when samples were exposed to

  6. 78 FR 29698 - Availability of an Environmental Assessment for Field Testing a Canine Lymphoma Vaccine, DNA

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-21

    ... a Canine Lymphoma Vaccine, DNA AGENCY: Animal and Plant Health Inspection Service, USDA. ACTION... testing, and then to field test, an unlicensed Canine Lymphoma Vaccine, DNA. The environmental assessment... vaccine and related information, examines the potential effects that field testing this veterinary...

  7. Small-scale field tests of attract-and-kill stations for pest Tephritid fruit flies

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Field tests were conducted at UF-TREC, Homestead to test efficacy of wax-matrix bait stations and mass trapping for control of the Caribbean fruit fly in a 5 by 30 tree guava planting. Results of the study and the ability to document control using small-scale field tests will be discussed....

  8. Comparison of field and laboratory-simulated drill-off tests

    SciTech Connect

    Bourdon, J.C.; Peltier, B. ); Cooper, G.A. ); Curry, D.A. ); McCann, D. )

    1989-12-01

    In this paper, field drill-off test results are compared with data from laboratory simulations. A simple theory for analyzing drill-off tests is developed. The weight-on bit (WOB) decay with time is close to exponential, but large threshold WOB's, resulting from poor weight transmission downhole, are sometimes observed in field tests.

  9. Field Dependence-Independence as a Variable in Second Language Cloze Test Performance.

    ERIC Educational Resources Information Center

    Stansfield, Charles; Hansen, Jacqueline

    1983-01-01

    A study of test performance and field dependent-independent (FD/I) cognitive style in 250 college students showed consistently positive correlation between FI and cloze test scores, and other measures such as final grade. It is suggested cloze tests may call forth cognitive restructuring capabilities more easily for more field independent…

  10. Field Test Evaluation of Conservation Retrofits of Low-Income, Single-Family Buildings in Wisconsin: Blower-Door-Directed Infiltration Reduction Procedure, Field Test Implementation and Results

    SciTech Connect

    Gettings, M.B.

    2001-05-21

    , and addition of the basic cost of determining the initial leakage rate to the recommended expenditure level. Recommendations for the field test of the procedure include increasing the number of houses in the sample, more timely examination of metered data to detect anomalies, and the monitoring of indoor air temperature. Though not appropriate in a field test of a procedure, further investigation into the effects of air leakage rate reductions on heating loads needs to be performed.

  11. Linking manipulative experiments to field data to test the dilution effect.

    PubMed

    Venesky, Matthew D; Liu, Xuan; Sauer, Erin L; Rohr, Jason R

    2014-05-01

    The dilution effect, the hypothesis that biodiversity reduces disease risk, has received support in many systems. However, few dilution effect studies have linked mechanistic experiments to field patterns to establish both causality and ecological relevance. We conducted a series of laboratory experiments and tested the dilution effect hypothesis in an amphibian-Batrachochytrium dendrobatidis (Bd) system and tested for consistency between our laboratory experiments and field patterns of amphibian species richness, host identity and Bd prevalence. In our laboratory experiments, we show that tadpoles can filter feed Bd zoospores and that the degree of suspension feeding was positively associated with their dilution potential. The obligate suspension feeder, Gastrophryne carolinensis, generally diluted the risk of chytridiomycosis for tadpoles of Bufo terrestris and Hyla cinerea, whereas tadpoles of B. terrestris (an obligate benthos feeder) generally amplified infections for the other species. In addition, G. carolinensis reduced Bd abundance on H. cinerea more so in the presence than absence of B. terrestris and B. terrestris amplified Bd abundance on H. cinerea more so in the absence than presence of G. carolinensis. Also, when ignoring species identity, species richness was a significant negative predictor of Bd abundance. In our analysis of field data, the presence of Bufo spp. and Gastrophryne spp. were significant positive and negative predictors of Bd prevalence, respectively, even after controlling for climate, vegetation, anthropogenic factors (human footprint), species richness and sampling effort. These patterns of dilution and amplification supported our laboratory findings, demonstrating that the results are likely ecologically relevant. The results from our laboratory and field data support the dilution effect hypothesis and also suggest that dilution and amplification are predictable based on host traits. Our study is among the first to link

  12. Field tests of syntheticManduca sexta sex pheromone.

    PubMed

    Tumlinson, J H; Mitchell, E R; Doolittle, R E; Jackson, D M

    1994-03-01

    In field experiments traps were baited with live females or with a two-, four-, or eight-component blend of the 16-carbon aldehydes previously identified as components of the sex pheromone emitted by femaleManduca sexta moths. The blends were formulated on rubber septa. Traps baited with a blend of all eight aldehydes captured moreM. sexta males than any other treatment. Septa loaded with 600 μg of the eight-component blend were attractive to males for about seven days in the field. Septa loaded with the eight-component blend and stored in a refrigerator at 4°C for a year released the conjugated diene and triene aldehydes at the same rate as freshly prepared septa and were equally attractive in the field.

  13. Initial field testing definition of subsurface sealing and backfilling tests in unsaturated tuff; Yucca Mountain Site Characterization Project

    SciTech Connect

    Fernandez, J.A.; Case, J.B.; Tyburski, J.R.

    1993-05-01

    This report contains an initial definition of the field tests proposed for the Yucca Mountain Project repository sealing program. The tests are intended to resolve various performance and emplacement concerns. Examples of concerns to be addressed include achieving selected hydrologic and structural requirements for seals, removing portions of the shaft liner, excavating keyways, emplacing cementitious and earthen seals, reducing the impact of fines on the hydraulic conductivity of fractures, efficient grouting of fracture zones, sealing of exploratory boreholes, and controlling the flow of water by using engineered designs. Ten discrete tests are proposed to address these and other concerns. These tests are divided into two groups: Seal component tests and performance confirmation tests. The seal component tests are thorough small-scale in situ tests, the intermediate-scale borehole seal tests, the fracture grouting tests, the surface backfill tests, and the grouted rock mass tests. The seal system tests are the seepage control tests, the backfill tests, the bulkhead test in the Calico Hills unit, the large-scale shaft seal and shaft fill tests, and the remote borehole sealing tests. The tests are proposed to be performed in six discrete areas, including welded and non-welded environments, primarily located outside the potential repository area. The final selection of sealing tests will depend on the nature of the geologic and hydrologic conditions encountered during the development of the Exploratory Studies Facility and detailed numerical analyses. Tests are likely to be performed both before and after License Application.

  14. Testing chameleon theories with light propagating through a magnetic field

    SciTech Connect

    Brax, Philippe; Davis, Anne-Christine; Mota, David F.

    2007-10-15

    It was recently argued that the observed PVLAS anomaly can be explained by chameleon field theories in which large deviations from Newton's law can be avoided. Here we present the predictions for the dichroism and the birefringence induced in the vacuum by a magnetic field in these models. We show that chameleon particles behave very differently from standard axionlike particles (ALPs). We find that, unlike ALPs, the chameleon particles are confined within the experimental setup. As a consequence, the birefringence is always bigger than the dichroism in PVLAS-type experiments.

  15. ANOLE Portable Radiation Detection System Field Test and Evaluation Campaign

    SciTech Connect

    Chris A. Hodge

    2007-07-12

    Handheld, backpack, and mobile sensors are elements of the Global Nuclear Detection System for the interdiction and control of illicit radiological and nuclear materials. They are used by the U.S. Department of Homeland Security (DHS) and other government agencies and organizations in various roles for border protection, law enforcement, and nonproliferation monitoring. In order to systematically document the operational performance of the common commercial off-the-shelf portable radiation detection systems, the DHS Domestic Nuclear Detection Office conducted a test and evaluation campaign conducted at the Nevada Test Site from January 18 to February 27, 2006. Named “Anole,” it was the first test of its kind in terms of technical design and test complexities. The Anole test results offer users information for selecting appropriate mission-specific portable radiation detection systems. The campaign also offered manufacturers the opportunity to submit their equipment for independent operationally relevant testing to subsequently improve their detector performance. This paper will present the design, execution, and methodologies of the DHS Anole portable radiation detection system test campaign.

  16. Radiation Isotope Identification Device (RIIDs) Field Test and Evaluation Campaign

    SciTech Connect

    Christopher Hodge, Raymond Keegan

    2007-08-01

    Handheld, backpack, and mobile sensors are elements of the Global Nuclear Detection System for the interdiction and control of illicit radiological and nuclear materials. They are used by the U.S. Department of Homeland Security (DHS) and other government agencies and organizations in various roles for border protection, law enforcement, and nonproliferation monitoring. In order to systematically document the operational performance of the common commercial off-the-shelf portable radiation detection systems, the DHS Domestic Nuclear Detection Office conducted a test and evaluation campaign conducted at the Nevada Test Site from January 18 to February 27, 2006. Named 'Anole', it was the first test of its kind in terms of technical design and test complexities. The Anole test results offer users information for selecting appropriate mission-specific portable radiation detection systems. The campaign also offered manufacturers the opportunity to submit their equipment for independent operationally relevant testing to subsequently improve their detector performance. This paper will present the design, execution, and methodologies of the DHS Anole portable radiation detection system test campaign.

  17. Field testing the wildlink capture collar on wolves

    USGS Publications Warehouse

    Mech, L.D.; Gese, E.M.

    1992-01-01

    Seventeen Wildlink capture collars were tested 61 times on 18 gray wolves (Canis lupus) during 1989-1991 in the Superior National Forest of northeastern Minnesota. Overall success rate was 89%, and most failures were attributable to premature battery expiration. When batteries were changed .ltoreq. every 2 months, 17 of 17 tests succeeded. With an upgraded version of the collar in which batteries lasted longer, 17 of 18 tests succeeded. Over the 2-year study, 6 of the 17 collars were lost. For serially recapturing individuals, the Wildlink collar proved useful and reliable if care was taken to replace batteries at proper intervals.

  18. Workplace field testing of the pressure drop of particulate respirators using welding fumes.

    PubMed

    Cho, Hyun-Woo; Yoon, Chung-Sik

    2012-10-01

    In a previous study, we concluded that respirator testing with a sodium chloride aerosol gave a conservative estimate of filter penetration for welding fume aerosols. A rapid increase in the pressure drop (PD) of some respirators was observed as fumes accumulated on the filters. The present study evaluated particulate respirator PD based on workplace field tests. A field PD tester was designed and validated using the TSI 8130 Automatic Filter Tester, designed in compliance with National Institute for Occupational and Safety and Health regulation 42 CFR part 84. Three models (two replaceable dual-type filters and one replaceable single-type filter) were evaluated against CO(2) gas arc welding on mild steel in confined booths in the workplace. Field tests were performed under four airborne concentrations (27.5, 15.4, 7.9, and 2.1 mg m(-3)). The mass concentration was measured by the gravimetric method, and number concentration was monitored using P-Trak (Model 8525, TSI, USA). Additionally, photos and scanning electron microscopy-energy dispersive X-ray spectroscopy were used to visualize and analyze the composition of welding fumes trapped in the filters. The field PD tester showed no significant difference compared with the TSI tester. There was no significant difference in the initial PD between laboratory and field results. The PD increased as a function of fume load on the respirator filters for all tested models. The increasing PD trend differed by models, and PD increased rapidly at high concentrations because greater amount of fumes accumulated on the filters in a given time. The increase in PD as a function of fume load on the filters showed a similar pattern as fume load varied for a particular model, but different patterns were observed for different models. Images and elemental analyses of fumes trapped on the respirator filters showed that most welding fumes were trapped within the first layer, outer web cover, and second layer, in order, while no fumes

  19. Reverberant Acoustic Testing and Direct Field Acoustic Testing Acoustic Standing Waves and their Impact on Structural Responses

    NASA Technical Reports Server (NTRS)

    Kolaini, Ali R.; Doty, Benjamin; Chang, Zensheu

    2012-01-01

    The aerospace industry has been using two methods of acoustic testing to qualify flight hardware: (1) Reverberant Acoustic Test (RAT), (2) Direct Field Acoustic Test (DFAT). The acoustic field obtained by RAT is generally understood and assumed to be diffuse, expect below Schroeder cut-of frequencies. DFAT method of testing has some distinct advantages over RAT, however the acoustic field characteristics can be strongly affected by test setup such as the speaker layouts, number and location of control microphones and control schemes. In this paper the following are discussed based on DEMO tests performed at APL and JPL: (1) Acoustic wave interference patterns and acoustic standing waves, (2) The structural responses in RAT and DFAT.

  20. CATION TRANSPORT AND PARTITIONING DURING A FIELD TEST OF ELECTROOSMOSIS

    EPA Science Inventory

    Field experiments were conducted to evaluate the effects of soil properties, such as the cation exchange capacity and mineral content, on pH, soluble ion concentrations, and electrical conductivity during electroosmosis in a silty clay soil. The soil is composed mainly of quartz ...

  1. Laboratory and Field Tests of Ultrasonic Sensors for Precision Sprayers

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Reliable function of sensors under rough field conditions is required for the development of variable-rate sprayers to deliver pest control agents to tree liners in ornamental nurseries. Two ultrasonic sensors were examined to identify how their durability and detection stability would be influenced...

  2. 47 CFR 73.1515 - Special field test authorizations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... immediate direction of an operator holding a commercial radio operator license (any class, unless otherwise... Section 73.1515 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field...

  3. SMART Wind Turbine Rotor: Design and Field Test

    SciTech Connect

    Berg, Jonathan C.; Resor, Brian R.; Paquette, Joshua A.; White, Jonathan R.

    2014-01-29

    This report documents the design, fabrication, and testing of the SMART Rotor. This work established hypothetical approaches for integrating active aerodynamic devices (AADs) into the wind turbine structure and controllers.

  4. Soldier Performance Research Project: Armor Field and SIMNET Tests

    DTIC Science & Technology

    1989-09-01

    Event 5. The crew will react to an ATGM ambush. The TC must issue the contact report and fire command (both timed). The tank should take evasive ...Cammand’s (TEXO34) Armor and Engineer Board who conducted the Soldier Performance Research Project (SPRP) Armor tests: MC Royce Simson, Test Director CPI...the Soldier Performance Research Project (SPP), the Armor portion was conducted in two phases to provide a rigorous assessment of the cognitive skill

  5. Field-test results using a nacelle-mounted lidar for improving wind turbine power capture by reducing yaw misalignment

    NASA Astrophysics Data System (ADS)

    Fleming, P. A.; Scholbrock, A. K.; Jehu, A.; Davoust, S.; Osler, E.; Wright, A. D.; Clifton, A.

    2014-06-01

    In this paper, a nacelle-mounted lidar was used to improve the yaw alignment of an experimental wind turbine. Using lidar-recorded data during normal operation, an error correction value for the nacelle vane wind direction measurement used in the yaw controller was determined. A field test was then conducted in which the turbine was operated with and without the correction applied to the yaw controller. Results demonstrated a significant increase in power capture. In addition, the study includes analysis on the impacts on loading of applying this yaw correction. The study demonstrates a successful application in field testing of using a nacelle-mounted lidar to improve turbine performance.

  6. Cyclic CO sub 2 injection for light oil recovery: Performance of a cost shared field test in Louisiana

    SciTech Connect

    Bassiouni, Z.A.; Groves, F.R. Jr.; Wolcott, J.M.

    1989-01-01

    The ultimate objective of this research is to provide a base of knowledge on the CO{sub 2} huff n' puff process for the enhanced recovery of Louisiana crude oil. Project goals include laboratory corefloods to investigate several parameters important to the process, and numerical simulation to interpret coreflood results. Additional activities include construction and analysis of a field test data base to facilitate target reservoir screening, and to identify sensitive operational parameters. The information from laboratory corefloods and data base evaluations will be used in the design and implementation of a Department of Energy sponsored field test. 1 ref.

  7. The life closure scale: additional psychometric testing of a tool to measure psychological adaptation in death and dying.

    PubMed

    Dobratz, Marjorie C

    2004-02-01

    The purpose of this study was to conduct additional psychometric testing on an instrument designed to measure psychological adaptation in end-of-life populations across a wide spectrum of terminal illnesses. A sample of 20 participants completed initial testing of the Life Closure Scale (LCS); however, its usefulness was limited by the small sample size. A larger sample of 113 home hospice individuals who met established criteria and who gave informed consent completed the 27-item LCS for additional psychometric testing. Cronbach's alphas and correlation coefficients were computed, and factor analysis was conducted to establish internal consistency reliability, theoretical clarity, and criterion-related validity. The number of scale items was reduced to 20, with a total alpha of.87. Cronbach's alphas for the two subscales were.80 (self-reconciled) and.82 (self-restructuring). Item-total correlations for the subscales ranged from a low of.37 to a high of.68, with confirmatory factor analysis yielding two loadings. These findings lend credence to the usefulness of the LCS in measuring psychological adaptation in dying persons.

  8. In situ destruction of contaminants via hydrous pyrolysis/oxidation. Visalia Field Test

    SciTech Connect

    Newmark, Robin L.; Aines, Roger D.; Knauss, Kevin; Leif, Roald; Chiarappa, Marina; Hudson, Bryant; Carrigan, Charles; Tompson, Andy; Richards, Jim; Eaker, Craig; Weidner, Randall; Sciarotta, Terry

    1998-12-01

    A field test of hydrous pyrolysis/oxidation (HPO) was conducted during the summer of 1997, during a commercial application of thermal remediation (Dynamic Underground Stripping (DUS)) at the Visalia Pole Yard (a super-fund site) in southern California. At Visalia, Southern California Edison Co. is applying the DUS thermal remediation method to clean up a large (4.3 acre) site contaminated with pole-treating compounds. This is a full-scale cleanup, during which initial extraction of contaminants is augmented by combined steam/air injection in order to enhance the destruction of residual contaminants by HPO. Laboratory results indicate that the contaminants at Visaha react at similar rates to TCE, which has been the focus of extensive laboratory work (Knauss et al., 1998a-c). Field experimental results from this application yield valuable information (1) confirming the destruction of contaminants in soil and groundwater by HPO, (2) validating the predictive models used to design HP0 steam injection systems, (3) demonstrating that accurate field measurements of the critical fluid parameters can be obtained using existing monitoring wells and (4) obtaining a reasonable prediction of the cost and effectiveness of HPO, working at a commercial scale and with commercial partners. The goal of our additional study and demonstration in conjunction with Edison has been to obtain early proof of hydrous pyrolysis/oxidation in the field, and validate our predictive models and monitoring strategies. This demonstration provides valuable economic and practicability data obtained on a commercial scale, with more detailed field validation than is commonly available on a commercially-conducted cleanup. The results of LLNL' s field experiments constrain the destruction rates throughout the site, and enable site management to make accurate estimates of total in situ destruction based on the recovered carbon. As of October, 1998, over 900,000 lb of contaminant have been removed from the

  9. Design and Installation of a Disposal Cell Cover Field Test

    SciTech Connect

    Benson, C.H.; Waugh, W.J.; Albright, W.H.; Smith, G.M.; Bush, R.P.

    2011-02-27

    The U.S. Department of Energy’s Office of Legacy Management (LM) initiated a cover assessment project in September 2007 to evaluate an inexpensive approach to enhancing the hydrological performance of final covers for disposal cells. The objective is to accelerate and enhance natural processes that are transforming existing conventional covers, which rely on low-conductivity earthen barriers, into water balance covers, that store water in soil and release it as soil evaporation and plant transpiration. A low conductivity cover could be modified by deliberately blending the upper layers of the cover profile and planting native shrubs. A test facility was constructed at the Grand Junction, Colorado, Disposal Site to evaluate the proposed methodology. The test cover was constructed in two identical sections, each including a large drainage lysimeter. The test cover was constructed with the same design and using the same materials as the existing disposal cell in order to allow for a direct comparison of performance. One test section will be renovated using the proposed method; the other is a control. LM is using the lysimeters to evaluate the effectiveness of the renovation treatment by monitoring hydrologic conditions within the cover profile as well as all water entering and leaving the system. This paper describes the historical experience of final covers employing earthen barrier layers, the design and operation of the lysimeter test facility, testing conducted to characterize the as-built engineering and edaphic properties of the lysimeter soils, the calibration of instruments installed at the test facility, and monitoring data collected since the lysimeters were constructed.

  10. Some arguments in favor of a Myriophyllum aquaticum growth inhibition test in a water-sediment system as an additional test in risk assessment of herbicides.

    PubMed

    Tunić, Tanja; Knežević, Varja; Kerkez, Đurđa; Tubić, Aleksandra; Šunjka, Dragana; Lazić, Sanja; Brkić, Dragica; Teodorović, Ivana

    2015-09-01

    The present study compares the practicability, reproducibility, power, and sensitivity of a Myriophyllum aquaticum growth inhibition test in a water-sediment system with the recently accepted Myriophyllum spicatum test in an equivalent testing system and the standard Lemna sp. test. Special consideration was given to endpoints based on M. aquaticum control plant growth and variability of relative growth rate and yield: shoot length, fresh weight, dry weight, and root weight. Sensitivity analysis was based on tests performed with 3,5-dichlorophenol, atrazine, isoproturon, trifluralin, 2,4-dichlorophenoloxyacetic acid, and dicamba. Growth rates for average M. aquaticum control plants were 0.119 d(-1) and 0.112 d(-1), with average estimated doubling time 6.33 d and 6.74 d for relative growth rate fresh weight and shoot length, respectively. Intrinsic variability of M. aquaticum endpoints was low: 12.9%, 12.5%, and 17.8% for relative growth rate shoot length, relative growth rate fresh weight and yield fresh weight, respectively. The power of the test was fairly high. When the most sensitive endpoints were used for comparison, the 2 Myriophyllum species were similarly sensitive, more sensitive (in the case of auxin simulators), or at least equally sensitive as Lemna minor to other tested herbicides. The M. aquaticum 10-d test with a 7-d exposure period in a water-sediment system has acceptable sensitivity and can provide repeatable, reliable, and reproducible results; therefore, it should not be disregarded as a good and representative additional test in environmental risk assessment.

  11. Field Testing of Compartmentalization Methods for Multifamily Construction

    SciTech Connect

    Ueno, K.; Lstiburek, J.

    2015-03-01

    The 2012 IECC has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure for both single-family and multifamily construction in Climate Zones 3-8. Other programs (LEED, ASHRAE 189, ASHRAE 62.2) have similar or tighter compartmentalization requirements, driving the need for easier and more effective methods of compartmentalization in multifamily buildings. Builders and practitioners have found that fire-resistance rated wall assemblies are a major source of difficulty in air sealing/compartmentalization, particularly in townhouse construction. This problem is exacerbated when garages are “tucked in” to the units and living space is located over the garages. In this project, Building Science Corporation examined the taping of exterior sheathing details to improve air sealing results in townhouse and multifamily construction, when coupled with a better understanding of air leakage pathways. Current approaches are cumbersome, expensive, time consuming, and ineffective; these details were proposed as a more effective and efficient method. The effectiveness of these air sealing methods was tested with blower door testing, including “nulled” or “guarded” testing (adjacent units run at equal test pressure to null out inter-unit air leakage, or “pressure neutralization”). Pressure diagnostics were used to evaluate unit-to-unit connections and series leakage pathways (i.e., air leakage from exterior, into the fire-resistance rated wall assembly, and to the interior).

  12. Field testing the prototype BNL fan-atomized oil burner

    SciTech Connect

    McDonald, R.; Celebi, Y.

    1995-04-01

    BNL has developed a new oil burner design referred to as the Fan Atomized burner System. The primary objective of the field study was to evaluate and demonstrate the reliable operation of the Fan Atomized Burner. The secondary objective was to establish and validate the ability of a low firing rate burner (0.3-0.4 gph) to fully satisfy the heating and domestic hot water load demands of an average household in a climate zone with over 5,000 heating-degree-days. The field activity was also used to evaluate the practicality of side-wall venting with the Fan Atomized Burner with a low stack temperature (300F) and illustrate the potential for very high efficiency with an integrated heating system approach based on the Fan Atomized Burner.

  13. Interactive effects of nitrogen addition, warming and invasion across organizational levels in an old-field plant community.

    PubMed

    Gornish, Elise S

    2014-10-08

    Response to global change is dependent on the level of biological organization (e.g. the ecologically relevant spatial scale) in which species are embedded. For example, individual responses can affect population-level responses, which, in turn, can affect community-level responses. Although relationships are known to exist among responses to global change across levels of biological organization, formal investigations of these relationships are still uncommon. I conducted an exploratory analysis to identify how nitrogen addition and warming by open top chambers might affect plants across spatial scales by estimating treatment effect size at the leaf level, the plant level and the community level. Moreover, I investigated if the presence of Pityopsis aspera, an experimentally introduced plant species, modified the relationship between spatial scale and effect size across treatments. I found that, overall, the spatial scale significantly contributes to differences in effect size, supporting previous work which suggests that mechanisms driving biotic response to global change are scale dependent. Interestingly, the relationship between spatial scale and effect size in both the absence and presence of experimental invasion is very similar for nitrogen addition and warming treatments. The presence of invasion, however, did not affect the relationship between spatial scale and effect size, suggesting that in this system, invasion may not exacerbate or attenuate climate change effects. This exercise highlights the value of moving beyond integration and scaling to the practice of directly testing for scale effects within single experiments.

  14. Far-Field Antenna Pattern From a Near-Field Test

    NASA Technical Reports Server (NTRS)

    Rahmat-Samii, Y.; Galindo-Israel, V.; Mittra, R.

    1982-01-01

    Plane/polar geometry simplifies measurement of near-field data for this antenna and allows a determination of far-field pattern by Jacobi-Bessel series expansion of data. Measuring probe is an undersized, dielectrically loaded and open-ended waveguide with a far-field pattern similar to that of a small magnetic dipole in its forward directions, making it unnecessary to rotate probe in direction similar to antenna rotation.

  15. Field testing, refinement, and psychometric evaluation of a new measure of nursing home care quality.

    PubMed

    Rantz, Marilyn J; Zwygart-Stauffacher, Mary; Mehr, David R; Petroski, Gregory F; Owen, Steven V; Madsen, Richard W; Flesner, Marcia; Conn, Vicki; Bostick, Jane; Smith, Robyn; Maas, Meridean

    2006-01-01

    The primary aim of this NINR-NIH-funded field test in 407 nursing homes in 3 states was to complete the development of and conduct psychometric testing for the Observable Indicators of Nursing Home Care Quality Instrument (Observable Indicators, OIQ). The development of the OIQ was based on extensive qualitative and iterative quantitative work that described nursing home care quality and did initial validity and reliability field testing of the instrument in 123 nursing homes in 1 state. The scale is meant for researchers, consumers, and regulators interested in directly observing and quickly evaluating (within 30 minutes of observation) the multiple dimensions of care quality in nursing homes. After extensive testing in this study, the Observable Indicators instrument has been reduced to 30 reliable and discriminating items that have a conceptually coherent hierarchical factor structure that describes nursing home care quality. Seven first-order factors group together into two second-order factors of Structure (includes Environment: Basics and Odors) and Process (includes Care Delivery, Grooming, Interpersonal Communication, Environment: Access, and Environment: Homelike) that are classic constructs of Quality, which was the third-order factor. Internal consistency reliability for the 7 first-order factors ranged from .77 to .93. Construct validity analyses revealed an association between survey citations and every subscale as well as the total score of the OIQ instrument. Known groups analysis revealed expected trends in the OIQ scores. The Observable Indicators instrument as a whole shows acceptable interrater and test-retest reliabilities, and strong internal consistency. Scale subscales show acceptable reliability as well. Generalizability Theory analyses revealed that dependability of scores can be improved by including a second site observer, or by revisiting a site. There is a small additional benefit from increasing observers or visits beyond two.

  16. Implementing the Mars Science Laboratory Terminal Descent Sensor Field Test Campaign

    NASA Technical Reports Server (NTRS)

    Montgomery, James F.; Bodie, James H.; Brown, Joseph D.; Chen, Allen; Chen, Curtis W.; Essmiller, John C.; Fisher, Charles D.; Goldberg, Hannah R.; Lee, Steven W.; Shaffer, Scott J.

    2012-01-01

    The Mars Science Laboratory (MSL) will deliver a 900 kg rover to the surface of Mars in August 2012. MSL will utilize a new pulse-Doppler landing radar, the Terminal Descent Sensor (TDS). The TDS employs six narrow-beam antennas to provide unprecedented slant range and velocity performance at Mars to enable soft touchdown of the MSL rover using a unique sky crane Entry, De-scent, and Landing (EDL) technique. Prior to use on MSL, the TDS was put through a rigorous verification and validation (V&V) process. A key element of this V&V was operating the TDS over a series of field tests, using flight-like profiles expected during the descent and landing of MSL over Mars-like terrain on Earth. Limits of TDS performance were characterized with additional testing meant to stress operational modes outside of the expected EDL flight profiles. The flight envelope over which the TDS must operate on Mars encompasses such a large range of altitudes and velocities that a variety of venues were neces-sary to cover the test space. These venues included an F/A-18 high performance aircraft, a Eurocopter AS350 AStar helicopter and 100-meter tall Echo Towers at the China Lake Naval Air Warfare Center. Testing was carried out over a five year period from July 2006 to June 2011. TDS performance was shown, in gen-eral, to be excellent over all venues. This paper describes the planning, design, and implementation of the field test campaign plus results and lessons learned.

  17. Tyndall AFB Bomb Damage Repair Field Test, Documentation and Analysis

    DTIC Science & Technology

    1975-10-01

    was not tested, as bping Irrele- vant to these tests. Simulation of this event was not attempted because it would have provided little or no...Richardson, Texas, Report No. AFWL-TR-71-42, October 1971. 11. Bussone, P.S., B.J. Bottomley, and G.C. Hoff , Rapid Repair of Bomb- Damaged Runways...Airfield Runways, Air Force Weapons Laboratory, Klrtland AFB, New Mexico, Report No. AFWL-TR-73-214, February 1974. 19. Hoff , George C, Investigation of

  18. Additional Reserve Recovery Using New Polymer Treatment on High Water Oil Ratio Wells in Alameda Field, Kingman County, Kansas

    SciTech Connect

    James Spillane

    2005-10-01

    The Chemical Flooding process, like a polymer treatment, as a tertiary (enhanced) oil recovery process can be a very good solution based on the condition of this field and its low cost compared to the drilling of new wells. It is an improved water flooding method in which high molecular-weight (macro-size molecules) and water-soluble polymers are added to the injection water to improve the mobility ratio by enhancing the viscosity of the water and by reducing permeability in invaded zones during the process. In other words, it can improve the sweep efficiency by reducing the water mobility. This polymer treatment can be performed on the same active oil producer well rather than on an injector well in the existence of strong water drive in the formation. Some parameters must be considered before any polymer job is performed such as: formation temperature, permeability, oil gravity and viscosity, location and formation thickness of the well, amount of remaining recoverable oil, fluid levels, well productivity, water oil ratio (WOR) and existence of water drive. This improved oil recovery technique has been used widely and has significant potential to extend reservoir life by increasing the oil production and decreasing the water cut. This new technology has the greatest potential in reservoirs that are moderately heterogeneous, contain moderately viscous oils, and have adverse water-oil mobility ratios. For example, many wells in Kansas's Arbuckle formation had similar treatments and we have seen very effective results. In addition, there were previous polymer treatments conducted by Texaco in Alameda Field on a number of wells throughout the Viola-Simpson formation in the early 70's. Most of the treatments proved to be very successful.

  19. Field Test of a DHW Distribution System: Temperature and Flow Analyses (Presentation)

    SciTech Connect

    Barley, C. D.; Hendron, B.; Magnusson, L.

    2010-05-13

    This presentation discusses a field test of a DHW distribution system in an occupied townhome. It includes measured fixture flows and temperatures, a tested recirculation system, evaluated disaggregation of flow by measured temperatures, Aquacraft Trace Wizard analysis, and comparison.

  20. Moving from the laboratory to the field: Adding natural environmental conditions to toxicology testing

    EPA Science Inventory

    While laboratory toxicology tests are generally easy to perform, cost effective and readily interpreted, they have been criticized for being unrealistic. In contrast, field tests are considered realistic while producing results that are difficult to interpret and expensive. To ...

  1. 40 CFR 1065.910 - PEMS auxiliary equipment for field testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement... overload the power system. (ii) The engine emissions do not change significantly as a result of the...

  2. Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

    SciTech Connect

    Bowers, J.S.; Anson, J.R.; Painter, S.M.

    1995-12-31

    Stabilization is a best demonstrated available technology, or BDAT. This technology traps toxic contaminants in a matrix so that they do not leach into the environment. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP the federal leach test) or the Soluble Threshold Leachate Concentration (STLC the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California`s and EPA`s, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. The concentration in the leachate is approximately ten times higher for the STLC procedure than the TCLP. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory (LLNL), additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens) when formulating a stabilization matrix, and they have a neutral pH. By using these clays and additives, LLNL`s highly concentrated wastewater treatment sludges have passed the TCLP and STLC tests. The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements.

  3. EZVI Injection Field Test Leads to Pilot-Scale Application

    EPA Science Inventory

    Testing and monitoring of emulsified zero-valent ironTM (EZVI) injections was conducted at Cape Canaveral Air Force Station’s Launch Complex 34, FL, in 2002 to 2005 to evaluate the technology’s efficacy in enhancing in situ dehalogenation of dense nonaqueous-phase liquid (DNAPL) ...

  4. Field Test of an Epidemiology Curriculum for Middle School Students

    ERIC Educational Resources Information Center

    Kaelin, Mark A.; Huebner, Wendy W.; Nicolich, Mark J.; Kimbrough, Maudellyn L.

    2007-01-01

    The purpose of this study was to test the effectiveness of a middle school epidemiology curriculum called Detectives in the Classroom. The curriculum presents epidemiology as the science of public health, using health-related issues that capture the interest of young students and help prepare them to make evidence-based health-related decisions.…

  5. Preparing Undergraduate Students for the Major Field Test in Business

    ERIC Educational Resources Information Center

    Bisalski, Heather Cooper; Helms, Marilyn M.; Whitesell, Melissa

    2017-01-01

    Many business programs address the learning of undergraduate students with an exit exam. A reference librarian and the business school faculty created an online test preparation study guide (or LibGuide) which included no-cost resources that were readily available yet academically authoritative to aid students in studying for the Educational…

  6. An integrated approach to monitoring a field test of in situ contaminant destruction

    SciTech Connect

    Aines, R D; Carrigan, C; Chiarappa, M; Eaker, C; Elsholtz, A; Hudson, G B; Leif, R; Newmark, R L

    1998-12-01

    The development of in situ thermal remediation techniques requires parallel development of techniques capable of monitoring the physical and chemical changes for purposes of process control. Recent research indicates that many common contaminants can be destroyed in situ by hydrous pyrolysis/oxidation (HPO), eliminating the need for costly surface treatment and disposal. Steam injection, combined with supplemental air, can create the conditions in which HP0 occurs. Field testing of this process, conducted in the summer of 1997, indicates rapid destruction of polycyclic aromatic hydrocarbons (PAHs). Previous work established a suite of underground geophysical imaging techniques capable of providing sufficient knowledge of the physical changes in the subsurface during thermal treatment at sufficient frequencies to be used to monitor and guide the heating and extraction processes. In this field test, electrical resistance tomography (ERT) and temperature measurements provided the primary information regarding the temporal and spatial distribution of the heated zones. Verifying the in situ chemical destruction posed new challenges. We developed field methods for sampling and analyzing hot water for contaminants, oxygen, intermediates and products of reaction. Since the addition of air or oxygen to the contaminated region is a critical aspect of HPO, noble gas tracers were used to identify fluids from different sources. The combination of physical monitoring with noble gas identification of the native and injected fluids and accurate fluid sampling resulted in an excellent temporal and spatial evaluation of the subsurface processes, from which the amount of in situ destruction occurring in the treated region could be quantified. The experimental field results constrain the destruction rates throughout the site, and enable site management to make accurate estimates of total in situ destruction based on the recovered carbon. As of October, 1998, over 400,000 kg (900

  7. Reservoir analysis study: Naval Petroleum Reserve No. 1, Elk Hills Field, Kern County, California: Phase 3 report, Recommended additional reservoir engineering analysis

    SciTech Connect

    Not Available

    1988-07-01

    The basis for completion of the Phase III tasks above were the reports of Phases I and II and the associated backup material. The Phase II report was reviewed to identify the major uncertainties in all of the reserve assignments. In addition to the Proved, Probable and Possible reserves of Phase II, ''potential reserves'' or those associated with a greater degree of risk than the Possible reserves included in the Phase II report, were also identified based on the work performed by Bergeson through the Phase II reporting date. Thirty-three specific studies were identified to address the major Phase II reserve uncertainties or these potential reserves. These studies are listed in Table 1 and are grouped by the Elk Hills pool designation. The basis and need for each study are elaborated in the discussion which follows. Where possible, the need for the study was quantified by associating the study with a particular reserve estimate which would be clarified by the analysis. This reserve value was either the Probable or Possible reserves which were being studied, the potential reserves that were identified, or simply the uncertainty inherent in the proved reserves as identified in the study purpose. The costs associated with performing the study are also shown in Table 1 and were estimated based on Bergeson's knowledge of the Elk Hills reservoirs and data base following Phases I and II, as well as the company's experience in performing similar studies in other fields. The cost estimates are considered reasonable for general budgeting purposes, but may require refinement prior to actual initiation of these studies. This is particularly true for studies involving field testing to obtain additional log, core or test information as the cost of such items is not considered in this report. 51 figs., 46 tabs.

  8. High SO{sub 2} removal efficiency testing. Topical report - results of sodium formate additive tests at New York State Electric & Gas Corporation`s Kintigh Station

    SciTech Connect

    Murphy, J.

    1997-02-14

    Tests were conducted at New York State Gas & Electric`s (NYSEG`s) Kintigh Station to evaluate options for achieving high sulfur dioxide (SO{sub 2}) removal efficiency in the wet limestone flue gas desulfurization (FGD) system. This test program was one of six conducted by the U.S. Department of Energy to evaluate low-capital-cost upgrades to existing FGD systems as a means for utilities to comply with the requirements of the 1990 Clean Air Act Amendments. The upgrade option tested at Kintigh was sodium formate additive. Results from the tests were used to calibrate the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) to the Kintigh scrubber configuration. FGDPRISM was then used to predict system performance for evaluating conditions other than those tested. An economic evaluation was then done to determine the cost effectiveness of various high-efficiency upgrade options. These costs can be compared with the estimated market value of SO{sub 2} allowance or the expected costs of allowances generated by other means, such as fuel switching or new scrubbers, to arrive at the most cost-effective strategy for Clean Air Act compliance.

  9. Cosmological tests of an axiverse-inspired quintessence field

    NASA Astrophysics Data System (ADS)

    Emami, Razieh; Grin, Daniel; Pradler, Josef; Raccanelli, Alvise; Kamionkowski, Marc

    2016-06-01

    Inspired by the string axiverse idea, it has been suggested that the recent transition from decelerated to accelerated cosmic expansion is driven by an axion-like quintessence field with a sub-Planckian decay constant. The scenario requires that the axion field be rather near the maximum of its potential but is less finely tuned than other explanations of cosmic acceleration. The model is parametrized by an axion decay constant f , the axion mass m , and an initial misalignment angle |θi| which is close to π . In order to determine the m and θi values consistent with observations, these parameters are mapped onto observables: the Hubble parameter H (z ) at an angular-diameter distance dA(z ) to redshift z =0.57 , as well as the angular sound horizon of the cosmic microwave background (CMB). Measurements of the baryon acoustic oscillation (BAO) scale at z ≃0.57 by the BOSS survey and Planck measurements of CMB temperature anisotropies are then used to probe the {m ,f ,θi} parameter space. With current data, CMB constraints are the most powerful, allowing a fraction of only ˜0.2 of the parameter-space volume. Measurements of the BAO scale made using the SPHEREx or SKA experiments could go further, observationally distinguishing all but ˜10-2 or ˜10-5 of the parameter-space volume (allowed by simple priors) from the Λ CDM model.

  10. Roadside tree/pole crash barrier field test

    NASA Technical Reports Server (NTRS)

    Wilson, A. H.

    1979-01-01

    A series of tests was carried out to evaluate the performance of a crash barrier designed to protect the occupants of an automobile from serious injury. The JPL barrier design is a configuration of empty aluminum beverage cans contained in a tear-resistant bag which, in turn, is encased in a collapsible container made of plywood and steel. Tests were conducted with a driven vehicle impacting the barrier. The basic requirements of NCHRP Report 153 were followed except that speeds of 30 mph rather than 60 mph were used. Accelerometer readings on the driver's helmet showed that the driver was never subjected to dangerous decelerations, and never experienced more than temporary discomfort. Also, all of the requirements of the cited report were met. An extrapolation of data indicated that the JPL barrier installed in front of a tree or telephone pole along a roadside would also have met the requirements at a speed of 40 mph.

  11. Summary of Tray Pack Field Acceptance Tests and Results

    DTIC Science & Technology

    1988-05-01

    test was conducted during 18-22 September 1984 at Fort Bragg, Fayetteville, NC. Eighteen items were tested since Turkey/Gravy, Chocolate Cake and...5.27 [3] (7.14) 5.54 [3] (7.08) 6.52 A (6.78) Chocolate Cake 4.63 R (6.68) 4 4.83 R (7.46) Egg Loaf w/Cheese 2.95 R (4.82) 3.33 R (5.24) 4.09 R (4.01...6.83) 7.3R A (6.60) Chocolate Pudding 5.52 [1] A (6.57) 5.49 [3) (6.64) 4.71 R (6.65) Turkey Sl w/Gravy [4) [4) 6.85 A Blueberry Cake [4] [4] 6.51 A

  12. CX-100 and TX-100 blade field tests.

    SciTech Connect

    Holman, Adam (USDA-Agriculture Research Service, Bushland, TX); Jones, Perry L.; Zayas, Jose R.

    2005-12-01

    In support of the DOE Low Wind Speed Turbine (LWST) program two of the three Micon 65/13M wind turbines at the USDA Agricultural Research Service (ARS) center in Bushland, Texas will be used to test two sets of experimental blades, the CX-100 and TX-100. The blade aerodynamic and structural characterization, meteorological inflow and wind turbine structural response will be monitored with an array of 75 instruments: 33 to characterize the blades, 15 to characterize the inflow, and 27 to characterize the time-varying state of the turbine. For both tests, data will be sampled at a rate of 30 Hz using the ATLAS II (Accurate GPS Time-Linked Data Acquisition System) data acquisition system. The system features a time-synchronized continuous data stream and telemetered data from the turbine rotor. This paper documents the instruments and infrastructure that have been developed to monitor these blades, turbines and inflow.

  13. Field test results of the three-dimensional acquisition and tracking (3DATA) sensor system

    NASA Astrophysics Data System (ADS)

    Fairchild, Paul W.; Lilly, David; Matkin, William B.

    2004-01-01

    Trex has developed two innovative MWIR tracking systems, the Rapid Optical Beam Steering (ROBS) system and the Fast InfraRed Sniper Tracker (FIRST). ROBS was developed by Trex in the mid 1980"s for BMDO and the Navy as a prototype 0.5 meter aperture, wide-angle, multiple target detection, tracking, and imaging system with laser ranging. The smaller FIRST system was developed in the mid 1990"s by Trex for DARPA to acquire and track small caliber bullets. Both systems utilize innovative fast steering methods for achieving very high acceleration rates, ~ 1,000 radians/sec2 for ROBS and ~ 40,000 radians/sec2 for the FIRST system. Each can provide high precision 3D tracking over a large field of regard and both have been demonstrated in field tests. Presently the capabilities of these systems are being expanded. A newer version of the ROBS, 3DATA, is being completed which will provide a capability to precisely track in three dimensions up to 20 targets per second, simultaneously. In addition, an upgraded FIRST system is being designed and built which will handle multiple slow targets in addition to the faster bullets.

  14. Field Test of a Steam Condenser Heat Sink Concept

    DTIC Science & Technology

    1974-01-01

    Research Branch, USA CRREL; and Marcus M. Greenberg, Mechanical Engi- neer, Research and Technology Division, U.S. Army Nuclear Power Group. The study...They were then most ably assisted by SP Brian Murray and SP Theodore Maffei in monitoring the test 24 hours a day, 7 days a week for 38 days. The...suspected ibai the steam rule had probably decieased, how- ever, a compaiison ol t’eed- waler iates indicates only a slight decrease m steam input

  15. Characterization of floating element balance for field panel testing

    NASA Astrophysics Data System (ADS)

    Hunsucker, J. Travis; Gardner, Harrison; Swain, Geoffrey

    2015-11-01

    Multiple experiments were performed to investigate and characterize the uncertainty and bias of a through-hull flush mounted floating element balance designed to measure the hydrodynamic drag forces of biofouling and marine coatings on 25 x 30 cm test panels. The instrument is located in a wet well on the aft portion of a 27' Chris Craft Commander. Testing occurs over a series of speeds ranging from a Froude number of 0.50-2.20 on calm days (force 3 or less) in waters along the central east coast of Florida. Recent modifications have been made to the instrumentation in an effort to improve the overall accuracy of the system. This study compares frictional drag measurements of the floating element balance to those obtained using the Clauser chart and Preston tube methods for a smooth surface. Boundary layer velocity profiles are examined to understand the nature of the flow over the testing section. Roughness function values for 60 and 220 grit sandpaper were calculated from data obtained using the floating element balance. These values were compared with previous work to examine the overall bias of the methodology. Repeat measurements for a smooth panel were analyzed to characterize the overall uncertainty in the system. This research was supported by the Office of Naval Research under grants N00014-10-1-0919 and N00014-11-1-0915.

  16. Pressure-interference testing of the Sumikawa geothermal field

    SciTech Connect

    Garg, S.K.; Pritchett, J.W.; Ariki, K.; Kawano, Y.

    1991-01-01

    Pressure interference tests have been used to determine the permeability structure of the Sumikawa reservoir. Interference tests between wells S-4 and KY-1 have indicated the presence of a very high permeability (140 md) north-south channel in the altered andesite layer. Pressure buildup data from well SN-7D have provided indications of a high transmissivity (kh {approx} 18 darcy-meters) reservoir located in the granodiorite layer, lack of pressure response in nearby shutin Sumikawa wells implies that the reservoir penetrated by SN-7D is isolated from the shallower reservoir in the altered andesites. The ''altered andesite'' and the ''granodiorite'' formations constitute the principal geothermal aquifers at Sumikawa. Pressure interference tests (wells KY-1 and SB-2, and wells KY-2 and SB-3) have also confirmed the presence of moderately high transmissivity ({approx} 2 darcy-meters) dacitic layers in the ''marine-volcanic complex'' formation. Because of its low vertical permeability, the ''marine volcanic complex'' formation constitutes an attractive target for the reinjection of waste geothermal fluids.

  17. Parentage verification in field progeny testing program of Mehsana buffalo.

    PubMed

    Jakhesara, S J; Rank, D N; Kansara, J D; Parikh, R C; Patel, V M; Vataliya, P H; Solanki, J V

    2012-12-01

    The present study was undertaken to construct a multiplex microsatellite panel for parentage testing in Mehsana buffalo (Bubalus bubalis). The study was based on a total of 212 Mehsana buffalos (100 dams, 100 daughters, and 12 sires). Genomic DNA was extracted from blood and semen samples. A panel of 10 microsatellite markers (CSSM61, ILSTS29, ILSTS17, ILSTS28, CSSM57, CSSM22, ILSTS61, CSSM8, ETH152, and ILSTS11) was amplified in a single multiplex reaction and analyzed by capillary electrophoresis on an automated DNA sequencer. The expected heterozygosity ranged from 0.642 to 0.833 (mean 0.762). The total exclusion probability using 10 microsatellite loci with 1 known parent was 0.993. Seven out of 10 microsatellite loci revealed relatively high polymorphic information content (>0.7). Eighty-one daughters out of 100 daughters qualified by compatibility according to Mendelism. The results suggest that multiplex microsatellite panel is a fast, robust, reliable, and economic tool to verify the parentage as well as to assign the putative sire to daughters under progeny testing with very high accuracy and hence can be used in routine parentage testing.

  18. Seismic Absorption and Modulus Measurements in Porous Rocks in Lab and Field: Physical, Chemical, and Biological Effects of Fluids (Detecting a Biosurfactant Additive in a Field Irrigation Experiment)

    SciTech Connect

    Spetzler, Hartmut

    2006-05-01

    We have been exploring a new technology that is based on using low-frequency seismic attenuation data to monitor changes in fluid saturation conditions in two-fluid phase porous materials. The seismic attenuation mechanism is related to the loss of energy due to the hysteresis of resistance to meniscus movement (changes in surface tension, wettability) when a pore containing two fluids is stressed at very low frequencies (< 10 Hz). This technology has potential applications to monitoring changes in (1) leakage at buried waste sites, (2) contaminant remediation, and (3) flooding during enhanced petroleum recovery. We have concluded a three year field study at the Maricopa Agricultural Center site of the University of Arizona. Three sets of instruments were installed along an East-West line perpendicular to the 50m by 50m inigation site. Each set of instruments consisted of one three component seismometer and one tiltmeter. Microseisms and solid Earth-tides served as strain sources. The former have a power peak at a period of about 6 seconds and the tides have about two cycles per day. Installation of instruments commenced in late summer of 2002. The instruments operated nearly continuously until April 2005. During the fall of 2003 the site was irrigated with water and one year later with water containing 150 ppm of a biosurfactant additive. This biodegradable additive served to mimic a class of contaminants that change the surface tension of the inigation fluid. Tilt data clearly show tidal tilts superimposed on local tilts due to agricultural irrigation and field work. When the observed signals were correlated with site specific theoretical tilt signals we saw no anomalies for the water irrigation in 2003, but large anomalies on two stations for the surfactant irrigation in 2004. Occasional failures of seismometers as well as data acquisition systems contributed to less than continuous coverage. These data are noisier than the tilt data, but do also show possible

  19. Field Testing of Activated Carbon Injection Options for Mercury Control at TXU's Big Brown Station

    SciTech Connect

    John Pavlish; Jeffrey Thompson; Christopher Martin; Mark Musich; Lucinda Hamre

    2009-01-07

    The primary objective of the project was to evaluate the long-term feasibility of using activated carbon injection (ACI) options to effectively reduce mercury emissions from Texas electric generation plants in which a blend of lignite and subbituminous coal is fired. Field testing of ACI options was performed on one-quarter of Unit 2 at TXU's Big Brown Steam Electric Station. Unit 2 has a design output of 600 MW and burns a blend of 70% Texas Gulf Coast lignite and 30% subbituminous Powder River Basin coal. Big Brown employs a COHPAC configuration, i.e., high air-to-cloth baghouses following cold-side electrostatic precipitators (ESPs), for particulate control. When sorbent injection is added between the ESP and the baghouse, the combined technology is referred to as TOXECON{trademark} and is patented by the Electric Power Research Institute in the United States. Key benefits of the TOXECON configuration include better mass transfer characteristics of a fabric filter compared to an ESP for mercury capture and contamination of only a small percentage of the fly ash with AC. The field testing consisted of a baseline sampling period, a parametric screening of three sorbent injection options, and a month long test with a single mercury control technology. During the baseline sampling, native mercury removal was observed to be less than 10%. Parametric testing was conducted for three sorbent injection options: injection of standard AC alone; injection of an EERC sorbent enhancement additive, SEA4, with ACI; and injection of an EERC enhanced AC. Injection rates were determined for all of the options to achieve the minimum target of 55% mercury removal as well as for higher removals approaching 90%. Some of the higher injection rates were not sustainable because of increased differential pressure across the test baghouse module. After completion of the parametric testing, a month long test was conducted using the enhanced AC at a nominal rate of 1.5 lb/Macf. During the

  20. Power of screening tests for colorectal cancer enhanced by high levels of M2-PK in addition to FOBT.

    PubMed

    Zaccaro, Cristina; Saracino, Ilaria Maria; Fiorini, Giulia; Figura, Natale; Holton, John; Castelli, Valentina; Pesci, Valeria; Gatta, Luigi; Vaira, Dino

    2017-02-02

    Colorectal cancer (CRC) is a multistep process that involves adenoma-carcinoma sequence. CRC can be prevented by routine screening, which can detect precancerous lesions. The aim of this study is to clarify whether faecal occult blood test (i-FOBT), tumor M2 pyruvate kinase (t-M2-PK), and endocannabinoid system molecules (cannabinoid receptors type 1-CB1, type 2-CB2, and fatty acid amide hydrolase-FAAH) might represent better diagnostic tools, alone or in combination, for an early diagnosis of CRC. An immunochemical FOB test (i-FOBT) and quantitative ELISA stool test for t-M2-PK were performed in 127 consecutive patients during a 12 month period. Endocannabinoid system molecules and t-M2-PK expression were detected by immunostaining in healthy tissues and normal mucosa surrounding adenomatous and cancerous colon lesions. i-FOBT and t-M2-PK combination leads to a better diagnostic accuracy for pre-neoplastic and neoplastic colon lesions. T-M2-PK quantification in stool samples and in biopsy samples (immunostaining) correlates with tumourigenesis stages. CB1 and CB2 are well expressed in healthy tissues, and their expression decreases in the presence of advanced stages of carcinogenesis and disappears in CRC. FAAH signal is well expressed in normal mucosa and low-risk adenoma, and increased in high-risk adenoma and carcinoma adjacent tissues. This study shows that high levels of t-M2-PK in addition to FOBT enhance the power of a CRC screening test. Endocannabinoid system molecule expression correlates with colon carcinogenesis stages. Developing future faecal tests for their quantification must be undertaken to obtain a more accurate early non-invasive diagnosis for CRC.