DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, W.; Kan, A.T.; Fu, G.

Neutral organic contaminants commonly reside on the solid portion of soils and sediments. The extent of desorption from these solids determines the fate, reactivity, and toxicity. Numerous researchers have observed that, after an initial exposure of a few days, desorption takes place in two phases, namely, an initial rapid release followed by a long-term resistant phase. Resistant desorption has been highly unpredictable. In this research, the adsorption and desorption of chlorobenzenes, hexachlorobutadiene, and naphthalene have been studied using historically and freshly contaminated bayou sediments from Lake Charles, Louisiana, USA. After an initial release period, both laboratory-spiked and historically contaminated sedimentsmore » from Lake Charles, Louisiana, USA. After an initial release period, both laboratory-spiked and historically contaminated sediments exhibit similar desorption profiles. The simulations compare favorably with previous in situ measurements. All desorption results, both laboratory and field, could reasonably be interpreted using a single irreversible isotherm. Consequences of these results in terms of sediment quality criteria (SQC) are also discussed. Finally, an index of fractional irreversible adsorption is proposed and tested.« less

Recent advances and results from the solid radiochemistry nuclear diagnostic at the National Ignition Facility

DOE PAGES

Gharibyan, N.; Shaughnessy, D. A.; Moody, K. J.; ...

2016-08-05

The solid debris collection capability at the National Ignition Facility has been expanded to include a third line-of-sight assembly. The solid radiochemistry nuclear diagnostic measurement of the ratio of gold isotopes is dependent on the efficient collection of neutron-activated hohlraum debris by passive metal disks. As a result, the collection of target debris at this new location is more reliable in comparison to the historic locations, and it appears to be independent of collector surface ablation.

Recent advances and results from the solid radiochemistry nuclear diagnostic at the National Ignition Facility.

PubMed

Gharibyan, N; Shaughnessy, D A; Moody, K J; Grant, P M; Despotopulos, J D; Faye, S A; Jedlovec, D R; Yeamans, C B

2016-11-01

The solid debris collection capability at the National Ignition Facility has been expanded to include a third line-of-sight assembly. The solid radiochemistry nuclear diagnostic measurement of the ratio of gold isotopes is dependent on the efficient collection of neutron-activated hohlraum debris by passive metal disks. The collection of target debris at this new location is more reliable in comparison to the historic locations, and it appears to be independent of collector surface ablation.

Solar System Exploration Augmented by Lunar and Outer Planet Resource Utilization: Historical Perspectives and Future Possibilities

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan

2014-01-01

Establishing a lunar presence and creating an industrial capability on the Moon may lead to important new discoveries for all of human kind. Historical studies of lunar exploration, in-situ resource utilization (ISRU) and industrialization all point to the vast resources on the Moon and its links to future human and robotic exploration. In the historical work, a broad range of technological innovations are described and analyzed. These studies depict program planning for future human missions throughout the solar system, lunar launched nuclear rockets, and future human settlements on the Moon, respectively. Updated analyses based on the visions presented are presented. While advanced propulsion systems were proposed in these historical studies, further investigation of nuclear options using high power nuclear thermal propulsion, nuclear surface power, as well as advanced chemical propulsion can significantly enhance these scenarios. Robotic and human outer planet exploration options are described in many detailed and extensive studies. Nuclear propulsion options for fast trips to the outer planets are discussed. To refuel such vehicles, atmospheric mining in the outer solar system has also been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as Helium 3 (3He) and hydrogen can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and hydrogen (deuterium, etc.) were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses have investigated resource capturing aspects of atmospheric mining in the outer solar system. These analyses included the gas capturing rate, storage options, and different methods of direct use of the captured gases. While capturing 3He, large amounts of hydrogen and 4He are produced. With these two additional gases, the potential for fueling small and large fleets of additional exploration and exploitation vehicles exists.

Solar System Exploration Augmented by Lunar and Outer Planet Resource Utilization: Historical Perspectives and Future Possibilities

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan

2014-01-01

Establishing a lunar presence and creating an industrial capability on the Moon may lead to important new discoveries for all of human kind. Historical studies of lunar exploration, in-situ resource utilization (ISRU) and industrialization all point to the vast resources on the Moon and its links to future human and robotic exploration. In the historical work, a broad range of technological innovations are described and analyzed. These studies depict program planning for future human missions throughout the solar system, lunar launched nuclear rockets, and future human settlements on the Moon, respectively. Updated analyses based on the visions presented are presented. While advanced propulsion systems were proposed in these historical studies, further investigation of nuclear options using high power nuclear thermal propulsion, nuclear surface power, as well as advanced chemical propulsion can significantly enhance these scenarios. Robotic and human outer planet exploration options are described in many detailed and extensive studies. Nuclear propulsion options for fast trips to the outer planets are discussed. To refuel such vehicles, atmospheric mining in the outer solar system has also been investigated as a means of fuel production for high energy propulsion and power. Fusion fuels such as helium 3 (3He) and hydrogen (H2) can be wrested from the atmospheres of Uranus and Neptune and either returned to Earth or used in-situ for energy production. Helium 3 and H2 (deuterium, etc.) were the primary gases of interest with hydrogen being the primary propellant for nuclear thermal solid core and gas core rocket-based atmospheric flight. A series of analyses have investigated resource capturing aspects of atmospheric mining in the outer solar system. These analyses included the gas capturing rate, storage options, and different methods of direct use of the captured gases. While capturing 3He, large amounts of hydrogen and 4He are produced. With these two additional gases, the potential for fueling small and large fleets of additional exploration and exploitation vehicles exists.

The Solid Rocket Motor Slag Population: Results of a Radar-based Regressive Statistical Evaluation

NASA Technical Reports Server (NTRS)

Horstman, Matthew F.; Xu, Yu-Lin

2008-01-01

Solid rocket motor (SRM) slag has been identified as a significant source of man-made orbital debris. The propensity of SRMs to generate particles of 100 m and larger has caused concern regarding their contribution to the debris environment. Radar observation, rather than in-situ gathered evidence, is currently the only measurable source for the NASA/ODPO model of the on-orbit slag population. This simulated model includes the time evolution of the resultant orbital populations using a historical database of SRM launches, propellant masses, and estimated locations and times of tail-off. However, due to the small amount of observational evidence, there can be no direct comparison to check the validity of this model. Rather than using the assumed population developed from purely historical and physical assumptions, a regressional approach was used which utilized the populations observed by the Haystack radar from 1996 to present. The estimated trajectories from the historical model of slag sources, and the corresponding plausible detections by the Haystack radar, were identified. Comparisons with observational data from the ensuing years were made, and the SRM model was altered with respect to size and mass production of slag particles to reflect the historical data obtained. The result is a model SRM population that fits within the bounds of the observed environment.

Torrefaction Processing for Human Solid Waste Management

NASA Technical Reports Server (NTRS)

Serio, Michael A.; Cosgrove, Joseph E.; Wójtowicz, Marek A.; Stapleton, Thomas J.; Nalette, Tim A.; Ewert, Michael K.; Lee, Jeffrey; Fisher, John

2016-01-01

This study involved a torrefaction (mild pyrolysis) processing approach that could be used to sterilize feces and produce a stable, odor-free solid product that can be stored or recycled, and also to simultaneously recover moisture. It was demonstrated that mild heating (200-250 C) in nitrogen or air was adequate for torrefaction of a fecal simulant and an analog of human solid waste (canine feces). The net result was a nearly undetectable odor (for the canine feces), complete recovery of moisture, some additional water production, a modest reduction of the dry solid mass, and the production of small amounts of gas and liquid. The liquid product is mainly water, with a small Total Organic Carbon content. The amount of solid vs gas plus liquid products can be controlled by adjusting the torrefaction conditions (final temperature, holding time), and the current work has shown that the benefits of torrefaction could be achieved in a low temperature range (< 250 C). These temperatures are compatible with the PTFE bag materials historically used by NASA for fecal waste containment and will reduce the energy consumption of the process. The solid product was a dry material that did not support bacterial growth and was hydrophobic relative to the starting material. In the case of canine feces, the solid product was a mechanically friable material that could be easily compacted to a significantly smaller volume (approx. 50%). The proposed Torrefaction Processing Unit (TPU) would be designed to be compatible with the Universal Waste Management System (UWMS), now under development by NASA. A stand-alone TPU could be used to treat the canister from the UWMS, along with other types of wet solid wastes, with either conventional or microwave heating. Over time, a more complete integration of the TPU and the UWMS could be achieved, but will require design changes in both units.

36 CFR 907.12 - Preparation of an environmental assessment.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Energy requirements and conservation; (vi) Solid waste; (vii) Transportation; (viii) Community facilities and services; (ix) Social and economic; (x) Historic and aesthetic; and (xi) Other relevant factors...

Isotopic variations of dissolved copper and zinc in stream waters affected by historical mining

USGS Publications Warehouse

Borrok, D.M.; Nimick, D.A.; Wanty, R.B.; Ridley, W.I.

2008-01-01

Zinc and Cu play important roles in the biogeochemistry of natural systems, and it is likely that these interactions result in mass-dependent fractionations of their stable isotopes. In this study, we examine the relative abundances of dissolved Zn and Cu isotopes in a variety of stream waters draining six historical mining districts located in the United States and Europe. Our goals were to (1) determine whether streams from different geologic settings have unique or similar Zn and Cu isotopic signatures and (2) to determine whether Zn and Cu isotopic signatures change in response to changes in dissolved metal concentrations over well-defined diel (24-h) cycles. Average ??66Zn and ??65Cu values for streams varied from +0.02??? to +0.46??? and -0.7??? to +1.4???, respectively, demonstrating that Zn and Cu isotopes are heterogeneous among the measured streams. Zinc or Cu isotopic changes were not detected within the resolution of our measurements over diel cycles for most streams. However, diel changes in Zn isotopes were recorded in one stream where the fluctuations of dissolved Zn were the largest. We calculate an apparent separation factor of ???0.3??? (66/64Zn) between the dissolved and solid Zn reservoirs in this stream with the solid taking up the lighter Zn isotope. The preference of the lighter isotope in the solid reservoir may reflect metabolic uptake of Zn by microorganisms. Additional field investigations must evaluate the contributions of soils, rocks, minerals, and anthropogenic components to Cu and Zn isotopic fluxes in natural waters. Moreover, rigorous experimental work is necessary to quantify fractionation factors for the biogeochemical reactions that are likely to impact Cu and Zn isotopes in hydrologic systems. This initial investigation of Cu and Zn isotopes in stream waters suggests that these isotopes may be powerful tools for probing biogeochemical processes in surface waters on a variety of temporal and spatial scales.

From Survey to FEM Analysis for Documentation of Built Heritage: the Case Study of Villa Revedin-Bolasco

NASA Astrophysics Data System (ADS)

Guarnieri, A.; Fissore, F.; Masiero, A.; Di Donna, A.; Coppa, U.; Vettore, A.

2017-05-01

In the last decade advances in the fields of close-range photogrammetry, terrestrial laser scanning (TLS) and computer vision (CV) have enabled to collect different kind of information about a Cultural Heritage objects and to carry out highly accurate 3D models. Additionally, the integration between laser scanning technology and Finite Element Analysis (FEA) is gaining particular interest in recent years for structural analysis of built heritage, since the increasing computational capabilities allow to manipulate large datasets. In this note we illustrate the approach adopted for surveying, 3D modeling and structural analysis of Villa Revedin-Bolasco, a magnificent historical building located in the small walled town of Castelfranco Veneto, in northern Italy. In 2012 CIRGEO was charged by the University of Padova to carry out a survey of the Villa and Park, as preliminary step for subsequent restoration works. The inner geometry of the Villa was captured with two Leica Disto D3a BT hand-held laser meters, while the outer walls of the building were surveyed with a Leica C10 and a Faro Focus 3D 120 terrestrial laser scanners. Ancillary GNSS measurements were also collected for 3D laser model georeferencing. A solid model was then generated from the laser global point cloud in Rhinoceros software, and portion of it was used for simulation in a Finite Element Analysis (FEA). In the paper we discuss in detail all the steps and challenges addressed and solutions adopted concerning the survey, solid modeling and FEA from laser scanning data of the historical complex of Villa Revedin-Bolasco.

Determination of turbidity patterns in Lake Chicot from LANDSAT MSS imagery

NASA Technical Reports Server (NTRS)

Lecroy, S. R. (Principal Investigator)

1982-01-01

A historical analysis of all the applicable LANDSAT imagery was conducted on the turbidity patterns of Lake Chicot, located in the southeastern corner of Arkansas. By examining the seasonal and regional turbidity patterns, a record of sediment dynamics and possible disposition can be obtained. Sketches were generated from the suitable imagery, displaying different intensities of brightness observed in bands 5 and 7 of LANDSAT's multispectral scanner data. Differences in and between bands 5 and 7 indicate variances in the levels of surface sediment concentrations. High sediment loads are revealed when distinct patterns appear in the band 7 imagery. Additionally, the upwelled signal is exponential in nature and saturates in band 5 at low wavelengths for large concentrations of suspended solids.

Pattern-formation under acoustic driving forces

NASA Astrophysics Data System (ADS)

Valverde, Jose Manuel

2015-07-01

Chemical and metallurgical processes enhanced by high intensity acoustic waves, thermoacoustic engines and refrigerators, fuel rods in nuclear reactors, heat exchanger tubes, offshore and vibrating structures, solar thermal collectors, acoustic levitators, microfluidic devices, cycling, musical acoustics, blood flow through veins/arteries, hearing in the mammalian ear, carbon nanotube loudspeakers, etc. The evolution of a myriad of processes involving the oscillation of viscous fluids in the presence of solid boundaries is up to a certain extent influenced by acoustic streaming. In addition to the sound field, viscous energy dissipation at the fluid-solid boundary causes a time-independent fluid circulation, which can lead to a significant enhancement of heat, mass and momentum transfer at large oscillation amplitudes. A particularly relevant phenomenon that can be notably affected by acoustic streaming is the promotion of sound waves by temperature gradients or viceversa (thermoacoustics), which is at the basis of potentially efficient and environmental friendly engines and refrigerators that have attracted a renewed interest in the last years. In the present manuscript, historical developments and the underlying basic physics behind acoustic streaming and thermoacoustics are reviewed from an unifying perspective.

Tribo-electric charging of dielectric solids of identical composition

NASA Astrophysics Data System (ADS)

Angus, John C.; Greber, Isaac

2018-05-01

Despite its long history and importance in many areas of science and technology, there is no agreement on the mechanisms responsible for tribo-electric charging, including especially the tribo-charging of chemically identical dielectric solids. Modeling of the excitation, diffusional transport, and de-excitation of electrons from hot spots shows that a difference in local surface roughness of otherwise identical solid dielectric objects leads to different transient excited electron concentrations during tribo-processes. The model predicts that excited electron concentrations are lower and concentration gradients higher in solids with rougher rather than smoother surfaces. Consequently, during contact, the flux of charge carriers (electrons or holes) from hot spots will be greater into the rougher solid than into the smoother solid. These predictions are in agreement with current and historical observations of tribo-electric charge transfer between solids of the same composition. This effect can take place in parallel with other processes and may also play a role in the charging of solids of different composition.

Shallow groundwater quality and geochemistry in the Fayetteville Shale gas-production area, north-central Arkansas, 2011

USGS Publications Warehouse

Kresse, Timothy M.; Warner, Nathaniel R.; Hays, Phillip D.; Down, Adrian; Vengosh, Avner; Jackson, Robert B.

2012-01-01

The Mississippian Fayetteville Shale serves as an unconventional gas reservoir across north-central Arkansas, ranging in thickness from approximately 50 to 550 feet and varying in depth from approximately 1,500 to 6,500 feet below the ground surface. Primary permeability in the Fayetteville Shale is severely limited, and successful extraction of the gas reservoir is the result of advances in horizontal drilling techniques and hydraulic fracturing to enhance and develop secondary fracture porosity and permeability. Drilling and production of gas wells began in 2004, with a steady increase in production thereafter. As of April 2012, approximately 4,000 producing wells had been completed in the Fayetteville Shale. In Van Buren and Faulkner Counties, 127 domestic water wells were sampled and analyzed for major ions and trace metals, with a subset of the samples analyzed for methane and carbon isotopes to describe general water quality and geochemistry and to investigate the potential effects of gas-production activities on shallow groundwater in the study area. Water-quality analyses from this study were compared to historical (pregas development) shallow groundwater quality collected in the gas-production area. An additional comparison was made using analyses from this study of groundwater quality in similar geologic and topographic areas for well sites less than and greater than 2 miles from active gas-production wells. Chloride concentrations for the 127 groundwater samples collected for this study ranged from approximately 1.0 milligram per liter (mg/L) to 70 mg/L, with a median concentration of 3.7 mg/L, as compared to maximum and median concentrations for the historical data of 378 mg/L and 20 mg/L, respectively. Statistical analysis of the data sets revealed statistically larger chloride concentrations (p-value <0.001) in the historical data compared to data collected for this study. Chloride serves as an important indicator parameter based on its conservative transport characteristics and relatively elevated concentrations in production waters associated with gas extraction activities. Major ions and trace metals additionally had lower concentrations in data gathered for this study than in the historical analyses. Additionally, no statistical difference existed between chloride concentrations from water-quality data collected for this study from 94 wells located less than 2 miles from a gas-production well and 33 wells located 2 miles or more from a gas-production well; a Wilcoxon rank-sum test showed a p-value of 0.71. Major ion chemistry was investigated to understand the effects of geochemical and reduction-oxidation (redox) processes on the shallow groundwater in the study area along a continuum of increased rock-water interaction represented by increases in dissolved solids concentration. Groundwater in sandstone formations is represented by a low dissolved solids concentration (less than 30 mg/L) and slightly acidic water type. Shallow shale aquifers were represented by dissolved solids concentrations ranging upward to 686 mg/L, and water types evolving from a dominantly mixed-bicarbonate and calcium-bicarbonate to a strongly sodium-bicarbonate water type. Methane concentration and carbon isotopic composition were analyzed in 51 of the 127 samples collected for this study. Methane occurred above a detection limit of 0.0002 mg/L in 32 of the 51 samples, with concentrations ranging upward to 28.5 mg/L. Seven samples had methane concentrations greater than or equal to 0.5 mg/L. The carbon isotopic composition of these higher concentration samples, including the highest concentration of 28.5 mg/L, shows the methane was likely biogenic in origin with carbon isotope ratio values ranging from -57.6 to -74.7 per mil. Methane concentrations increased with increases in dissolved solids concentrations, indicating more strongly reducing conditions with increasing rock-water interaction in the aquifer. As such, groundwater-quality data collected for this study indicate that groundwater chemistry in the shallow aquifer system in the study area is a result of natural processes, beginning with recharge of dilute atmospheric precipitation and evolution of observed groundwater chemistry through rock-water interaction and redox processes.

75 FR 30863 - Nixon Presidential Historical Materials: Opening of Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-02

... NATIONAL ARCHIVES AND RECORDS ADMINISTRATION Nixon Presidential Historical Materials: Opening of Materials AGENCY: National Archives and Records Administration. ACTION: Notice of opening of additional materials. SUMMARY: This notice announces the opening of additional Nixon Presidential Historical Materials...

Lubrication with solids.

NASA Technical Reports Server (NTRS)

Buckley, D. H.; Johnson, R. L.

1972-01-01

Brief discussion of the historical background, variety range, chemistry, physics, and other properties of solid lubricants, and review of their current uses. The widespread use of solid lubricants did not occur until about 1947. At present, they are the object of such interest that a special international conference on their subject was held in 1971. They are used at temperatures beyond the useful range of conventional lubricating oils and greases. Their low volatility provides them with the capability of functioning effectively in vacuum and invites their use in space applications. Their high load carrying ability makes them useful with heavily loaded components. Solid lubricants, however, do lack some of the desirable properties of conventional lubricants. Unlike oils and greases, which have fluidity and can continuously be carried back into contact with lubricated surfaces, solid lubricants, because of their immobility, have finite lives. Also, oils and greases can carry away frictional heat from contacting surfaces, while solid lubricants cannot.

Probabilistic failure assessment with application to solid rocket motors

NASA Technical Reports Server (NTRS)

Jan, Darrell L.; Davidson, Barry D.; Moore, Nicholas R.

1990-01-01

A quantitative methodology is being developed for assessment of risk of failure of solid rocket motors. This probabilistic methodology employs best available engineering models and available information in a stochastic framework. The framework accounts for incomplete knowledge of governing parameters, intrinsic variability, and failure model specification error. Earlier case studies have been conducted on several failure modes of the Space Shuttle Main Engine. Work in progress on application of this probabilistic approach to large solid rocket boosters such as the Advanced Solid Rocket Motor for the Space Shuttle is described. Failure due to debonding has been selected as the first case study for large solid rocket motors (SRMs) since it accounts for a significant number of historical SRM failures. Impact of incomplete knowledge of governing parameters and failure model specification errors is expected to be important.

Simulation of ground-water flow and the movement of saline water in the Hueco Bolson aquifer, El Paso, Texas, and adjacent areas

USGS Publications Warehouse

Groschen, George E.

1994-01-01

Results of the projected withdrawal simulations from 1984-2000 indicate that the general historical trend of saline-water movement probably will continue. The saline water in the Rio Grande alluvium is the major source of saline-water intrusion into the freshwater zone throughout the historical period and into the future on the basis of simulation results. Some saline water probably will continue to move downward from the Rio Grande alluvium to the freshwater below. Injection of treated sewage effluent into some wells will create a small zone of freshwater containing slightly increased amounts of dissolved solids in the northern area of the Texas part of the Hueco bolson aquifer. Many factors, such as well interference, pumping schedules, and other factors not specifically represented in the regional simulation, can substantially affect dissolved-solids concentrations at individual wells.

Recent and historic drivers of landscape change in the Everglades ridge, slough, and Tree Island mosaic

USGS Publications Warehouse

Larsen, Laurel G.; Nicholas Aumen,; Bernhardt, Christopher E.; Vic Engel,; Givnish, Thomas J.; S Hagerthey, P McCormick; Harvey, Judson; Lynn Leonard,; McCormick, P.; McVoy, Christopher; Noe, Gregory; Nungesser, Martha K.; Rutchey, K.; Sklar, Fred; Troxler, Tiffany G.; Volin, John C.; Willard, Debra A.

2011-01-01

More than half of the original Everglades extent formed a patterned peat mosaic of elevated ridges, lower and more open sloughs, and tree islands aligned parallel to the dominant flow direction. This ecologically important landscape structure remained in a dynamic equilibrium for millennia prior to rapid degradation over the past century in response to human manipulation of the hydrologic system. Restoration of the patterned landscape structure is one of the primary objectives of the Everglades restoration effort. Recent research has revealed that three main drivers regulated feedbacks that initiated and maintained landscape structure: the spatial and temporal distribution of surface water depths, surface and subsurface flow, and phosphorus supply. Causes of recent degradation include but are not limited to perturbations to these historically important controls; shifts in mineral and sulfate supply may have also contributed to degradation. Restoring predrainage hydrologic conditions will likely preserve remaining landscape pattern structure, provided a sufficient supply of surface water with low nutrient and low total dissolved solids content exists to maintain a rainfall-driven water chemistry. However, because of hysteresis in landscape evolution trajectories, restoration of areas with a fully degraded landscape could require additional human intervention.

The 10th anniversary of the publication of genes and environment: memoir of establishing the Japanese environmental mutagen society and a proposal for a new collaborative study on mutagenic hormesis.

PubMed

Sutou, Shizuyo

2017-01-01

The Japanese Environmental Mutagen Society (JEMS) was established in 1972 by 147 members, 11 of whom are still on the active list as of May 1, 2016. As one of them, I introduce some historic topics here. These include 1) establishment of JEMS, 2) the issue of 2-(2-furyl)-3-(3-nitro-2-furyl)acrylamide (AF-2), 3) the Mammalian Mutagenicity Study Group (MMS) and its achievements, and 4) the Collaborative Study Group of the Micronucleus Test (CSGMT) and its achievements. In addition to these historic matters, some of which are still ongoing, a new collaborative study is proposed on adaptive response or hormesis by mutagens. There is a close relationship between mutagens and carcinogens, the dose-response relationship of which has been thought to follow the linear no-threshold model (LNT). LNT was fabricated on the basis of Drosophila sperm experiments using high dose radiation delivered in a short period. The fallacious 60 years-old LNT is applied to cancer induction by radiation without solid data and then to cancer induction by carcinogens also without solid data. Therefore, even the smallest amount of carcinogens is postulated to be carcinogenic without thresholds now. Radiation hormesis is observed in a large variety of living organisms; radiation is beneficial at low doses, but hazardous at high doses. There is a threshold at the boundary between benefit and hazard. Hormesis denies LNT. Not a few papers report existence of chemical hormesis. If mutagens and carcinogens show hormesis, the linear dose-response relationship in mutagenesis and carcinogenesis is denied and thresholds can be introduced.

Evidence-Based Ethics for Neurology and Psychiatry Research

PubMed Central

Kim, Scott Y. H.

2004-01-01

Summary: American bioethics, historically arising out of theology and philosophy, has been dominated by the method of normative analysis. Ethics as policy, however, requires in addition a solid evidence base. This paper discusses the background conditions that make neurotherapeutics research particularly challenging. Three key ethical issues are discussed within an evidence-based ethics framework: the ethical challenges arising from changes in the financial incentive structures for academic researchers and their institutions, the challenges of risk-benefit analysis for neurotherapeutics protocols testing innovative interventions, and the evolving issues surrounding impaired decision-making capacity and surrogate consent for research. For each of these issues, selected empirical data are reviewed, areas for further inquiry are noted, and the need for development of novel methods for bioethics policy research is discussed. PMID:15717040

R. Bruce Merrifield and Solid-Phase Peptide Synthesis: A Historical Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, A R

2007-12-04

Bruce Merrifield, trained as a biochemist, had to address three major challenges related to the development and acceptance of solid-phase peptide synthesis (SPPS). The challenges were (1) to reduce the concept of peptide synthesis on a insoluble support to practice, (2) overcome the resistance of synthetic chemists to this novel approach, and (3) establish that a biochemist had the scientific credentials to effect the proposed revolutionary change in chemical synthesis. How these challenges were met is discussed in this article.

Historical water-quality data for the High Plains Regional Ground-Water Study Area in Colorado, Kansas, Nebraska, New Mexico, Oklahoma, South Dakota, Texas, and Wyoming, 1930-98

USGS Publications Warehouse

Litke, David W.

2001-01-01

The High Plains aquifer underlies 174,000 square miles in parts of eight States and includes eight primary hydrogeologic units, including the well-known Ogallala Formation. The High Plains aquifer is an important resource, providing water for 27 percent of the Nation?s irrigated agricultural lands in an otherwise dry landscape. Since the 1980?s there has been concern over the sustainability of the aquifer due to water-level declines caused by substantial pumping. Water quality of the aquifer is a more recent concern. As part of the U.S. Geological Survey?s National Water-Quality Assessment Program, historical water-quality data have been gathered for the High Plains Regional Ground-Water Study Area into a retrospective data base, which can be used to evaluate the occurrence and distribution of water-quality constituents of concern.Data from the retrospective data base verify that nitrate, pesticides, and dissolved solids (salinity) are important water-quality concerns in the High Plains study area. Sixteen percent of all measured nitrate concentrations were larger than the U.S. Environmental Protection Agency drinking-water standard of 10 milligrams per liter. In about 70 percent of the counties within the High Plains study area, nitrate concentrations for 1980-98 were significantly larger than for 1930-69. While nitrate concentrations are largest where depth to water is shallow, concentrations also have increased in the Ogallala Formation where depth to water is large. Pesticide data primarily are available only in the northern half of the study area. About 50 pesticides were detected in the High Plains study area, but only four pesticides (atrazine, alachlor, cyanazine, and simazine) had concentrations exceeding a drinking-water standard. The occasional detection of pesticides in deeper parts of the Ogallala Formation indicates that contamination pathways exist. Dissolved solids, which are a direct measure of salinity, had 29 percent of measured concentrations in excess of the secondary drinking-water standard of 500 milligrams per liter. Comparison of dissolved-solids concentrations prior to 1980 to concentrations after 1980 indicates dissolved-solids concentrations have increased in the alluvial valleys of the Platte, the Republican, and the Arkansas Rivers, as well as in the Ogallala Formation?South hydrogeologic unit.Water-quality results indicate that human activities are affecting the water of the High Plains aquifer. Because there is a potential for water quality to become impaired relative to the historical uses of the aquifer, water quality needs to be considered when evaluating the sustainability of the High Plains aquifer. Data collected as part of the High Plains Regional Ground-Water Study will help to fill in gaps in water-quality information and provide additional information for understanding the factors that govern ambient water quality.

The Mechanism of Atomization Accompanying Solid Injection

NASA Technical Reports Server (NTRS)

Castleman, R A , Jr

1933-01-01

A brief historical and descriptive account of solid injection is followed by a detailed review of the available theoretical and experimental data that seem to throw light on the mechanism of this form of atomization. It is concluded that this evidence indicates that (1) the atomization accompanying solid injection occurs at the surface of the liquid after it issues as a solid stream from the orifice; and (2) that such atomization has a mechanism physically identical with the atomization which takes place in an air stream, both being due merely to the formation, at the gas-liquid interface, of fine ligaments under the influence of the relative motion of gas and liquid, and to their collapse, under the influence of surface tension, to form the drops in the spray.

The mechanical problems on additive manufacturing of viscoelastic solids with integral conditions on a surface increasing in the growth process

NASA Astrophysics Data System (ADS)

Parshin, D. A.; Manzhirov, A. V.

2018-04-01

Quasistatic mechanical problems on additive manufacturing aging viscoelastic solids are investigated. The processes of piecewise-continuous accretion of such solids are considered. The consideration is carried out in the framework of linear mechanics of growing solids. A theorem about commutativity of the integration over an arbitrary surface increasing in the solid growing process and the time-derived integral operator of viscoelasticity with a limit depending on the solid point is proved. This theorem provides an efficient way to construct on the basis of Saint-Venant principle solutions of nonclassical boundary-value problems for describing the mechanical behaviour of additively formed solids with integral satisfaction of boundary conditions on the surfaces expanding due to the additional material influx to the formed solid. The constructed solutions will retrace the evolution of the stress-strain state of the solids under consideration during and after the processes of their additive formation. An example of applying the proved theorem is given.

Development and Characterization of a High-Solids Deacetylation Process

DOE PAGES

Shekiro, III, Joseph; Chen, Xiaowen; Smith, Holly; ...

2016-05-20

Dilute-acid pretreatment has proven to be a robust means of converting herbaceous feedstock to fermentable sugars. However, it also releases acetic acid, a known fermentation inhibitor, from acetyl groups present in the biomass. A mild, dilute alkaline extraction stage was implemented prior to acid pretreatment to separate acetic acid from the hydrolysate sugar stream. This step, termed deacetylation, improved the glucose and xylose yields from enzymatic hydrolysis and ethanol yields from fermentation of the sugars relative to the control experiments using dilute-acid pretreatment of native corn stover without deacetylation. While promising, deacetylation as it was historically practiced is conducted atmore » low solids loadings, and at fixed conditions. Thus, many questions have been left unanswered, including the relationship between sodium hydroxide and solids loading, and acetate and xylan solubilization, as well as the impact of temperature and residence time on the process efficacy. A central composite experiment was designed to evaluate the impact of solids loading, sodium hydroxide loading, reaction time and temperature during deacetylation on the acetate and xylan solubilization of corn stover. Using the ANOVA test, it became apparent that neither of the responses was significantly impacted by the solids loading, while the reaction time was a minor factor - the responses were largely driven by reaction temperature and the sodium hydroxide loading. Based on the results, we successfully demonstrated the ability to transition the low-solids (10 % w/w) deacetylation process to a higher-solids process (30 % w/w) with minimal impact on the ability to extract acetate from biomass. Conditions were selected to minimize xylose loss during deacetylation, while also removing 70 % of acetyl groups. The impact of selected conditions on the enzymatic hydrolysis and fermentation was further investigated. In conclusion, evaluation of the whole-process impact demonstrated that despite the upfront reduction in carbohydrate loss during deacetylation, the overall process sugar yields were depressed by the high-solids, low alkali process relative to the historical control. Consequently, ethanol titers were reduced, though strong fermentation performance was still observed, indicating that 70 % acetate removal is sufficient to depress acetic acid concentrations to a level that does not substantially inhibit ethanol fermentation by rZymomo nas.« less

Rubbish.

ERIC Educational Resources Information Center

Rathje, William L.

1989-01-01

Presents a historical perspective of garbage management, including an exploration of what is cited as myths about garbage that guide our thinking in dealing with solid waste disposal problems. A partial list of topics includes quantity of garbage, landfills, toxic wastes, technological fixes, economics, source reduction, resource recovery,…

Patterns of waste generation: A gradient boosting model for short-term waste prediction in New York City.

PubMed

Johnson, Nicholas E; Ianiuk, Olga; Cazap, Daniel; Liu, Linglan; Starobin, Daniel; Dobler, Gregory; Ghandehari, Masoud

2017-04-01

Historical municipal solid waste (MSW) collection data supplied by the New York City Department of Sanitation (DSNY) was used in conjunction with other datasets related to New York City to forecast municipal solid waste generation across the city. Spatiotemporal tonnage data from the DSNY was combined with external data sets, including the Longitudinal Employer Household Dynamics data, the American Community Survey, the New York City Department of Finance's Primary Land Use and Tax Lot Output data, and historical weather data to build a Gradient Boosting Regression Model. The model was trained on historical data from 2005 to 2011 and validation was performed both temporally and spatially. With this model, we are able to accurately (R2>0.88) forecast weekly MSW generation tonnages for each of the 232 geographic sections in NYC across three waste streams of refuse, paper and metal/glass/plastic. Importantly, the model identifies regularity of urban waste generation and is also able to capture very short timescale fluctuations associated to holidays, special events, seasonal variations, and weather related events. This research shows New York City's waste generation trends and the importance of comprehensive data collection (especially weather patterns) in order to accurately predict waste generation. Copyright © 2017. Published by Elsevier Ltd.

11. Historic American Buildings Survey California Historical Society Original: About ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Historic American Buildings Survey California Historical Society Original: About 1870 Re-photo: January 1940 CONVENTO AND ADDITIONS (VIEW FROM SOUTHWEST) - Mission San Jose de Guadalupe, Mission & Washington Boulevards, Fremont, Alameda County, CA

From Tls Survey to 3d Solid Modeling for Documentation of Built Heritage: the Case Study of Porta Savonarola in Padua

NASA Astrophysics Data System (ADS)

Guarnieri, A.; Fissore, F.; Masiero, A.; Vettore, A.

2017-08-01

It is a matter of fact that 3D visualisation and proper documentation of cultural objects helps to preserve the history and memories of historic buildings, archaeological sites and cultural landscapes, and supports economic growth by stimulating cultural tourism. Preservation, visualisation and recreation of valuable historical and architectural objects and places has always been a serious challenge for specialists in the field. Today, the rapid developments in the fields of close-range photogrammetry, terrestrial laser scanning (TLS) and computer vision (CV) enable to carry out highly accurate 3D models so as to be extremely effective and intuitive for users who have stringent requirements and high expectations. In this note we present the results of the survey and 3D modeling of an ancient gate, Porta Savonarola, located within the remains of the medieval town walls surrounding the historical city center of Padua, Italy. The work has been undertaken within the framework of the project "Walls Multimedia Museum" (WMM) promoted by the local private association "Padua Walls Committee". The goal of the project was to develop a prototype of an "extended" virtual museum, spreaded along most interesting locations of the town walls. The survey of the ancient gate was performed with a Leica C10 and P20 terrestrial laser scanners. Once the acquired scans were properly merged together, a solid model was generated from the global point cloud, and plans and elevations were extracted from it for restoration purposes. A short multimedia video was also created for the "Walls Multimedia Museum", showing both the outer and inner part of the gate. In the paper we will discuss all the steps and challenges addressed to provide the 3D solid model of Porta Savonarola from the TLS data.

Patterns of End-of-Life Care in Children with Advanced Solid Tumor Malignancies Enrolled on a Palliative Care Service

PubMed Central

Vern-Gross, Tamara Z.; Lam, Catherine G.; Graff, Zachary; Singhal, Sara; Levine, Deena R.; Gibson, Deborah; Coan, April; Anghelescu, Doralina L.; Yuan, Ying; Baker, Justin N.

2015-01-01

Context Pediatric patients with solid tumors can have a significant symptom burden that impacts quality of life and end-of-life care needs. Objectives We evaluated outcomes and symptoms in children with solid tumors, and compared patterns of end-of-life care after implementation of a dedicated institutional pediatric palliative care service. Methods We performed a retrospective cohort study of children with solid tumors treated at St. Jude Children’s Research Hospital, before and after implementation of the institutional Quality of Life/Palliative Care (QoL/PC) Service in January 2007. Patients who died between July 2001- February 2005 (historical cohort; n=134) were compared to those who died between January 2007- January 2012 (QoL/PC cohort; n=57). Results Median time to first QoL/PC consultation was 17.2 months (range, 9–33 months). At consultation, 60% of children were not receiving or discontinued cancer-directed therapy. Within the QoL/PC cohort, 54 patients had documented symptoms; 94% required intervention for ≥ 3 symptoms; 76% received intervention for ≥ 5 symptoms. Eighty-three percent achieved their preferred place of death. Compared to the historical cohort, the QoL/PC cohort had more end-of-life discussions per patient (median, 12 vs. 3; P<0.001), earlier end-of-life discussions, with longer times before do-not-resuscitate orders (median, 195 vs. 2 days; P<0.001), and greater hospice enrollment (71% vs. 46%, P=0.002). Conclusion Although children with solid tumor malignancies may have significant symptom burden towards end of life, positive changes were documented in communication and in places of care and death following implementation of a pediatric palliative care service. PMID:25891664

Use of historical information in extreme storm surges frequency analysis

NASA Astrophysics Data System (ADS)

Hamdi, Yasser; Duluc, Claire-Marie; Deville, Yves; Bardet, Lise; Rebour, Vincent

2013-04-01

The prevention of storm surge flood risks is critical for protection and design of coastal facilities to very low probabilities of failure. The effective protection requires the use of a statistical analysis approach having a solid theoretical motivation. Relating extreme storm surges to their frequency of occurrence using probability distributions has been a common issue since 1950s. The engineer needs to determine the storm surge of a given return period, i.e., the storm surge quantile or design storm surge. Traditional methods for determining such a quantile have been generally based on data from the systematic record alone. However, the statistical extrapolation, to estimate storm surges corresponding to high return periods, is seriously contaminated by sampling and model uncertainty if data are available for a relatively limited period. This has motivated the development of approaches to enlarge the sample extreme values beyond the systematic period. The nonsystematic data occurred before the systematic period is called historical information. During the last three decades, the value of using historical information as a nonsystematic data in frequency analysis has been recognized by several authors. The basic hypothesis in statistical modeling of historical information is that a perception threshold exists and that during a giving historical period preceding the period of tide gauging, all exceedances of this threshold have been recorded. Historical information prior to the systematic records may arise from high-sea water marks left by extreme surges on the coastal areas. It can also be retrieved from archives, old books, earliest newspapers, damage reports, unpublished written records and interviews with local residents. A plotting position formula, to compute empirical probabilities based on systematic and historical data, is used in this communication paper. The objective of the present work is to examine the potential gain in estimation accuracy with the use of historical information (to the Brest tide gauge located in the French Atlantic coast). In addition, the present work contributes to addressing the problem of the presence of outliers in data sets. Historical data are generally imprecise, and their inaccuracy should be properly accounted for in the analysis. However, as several authors believe, even with substantial uncertainty in the data, the use of historical information is a viable mean to improve estimates of rare events related to extreme environmental conditions. The preliminary results of this study suggest that the use of historical information increases the representativity of an outlier in the systematic data. It is also shown that the use of historical information, specifically the perception sea water level, can be considered as a reliable solution for the optimal planning and design of facilities to withstand extreme environmental conditions, which will occur during its lifetime, with an appropriate optimum of risk level. Findings are of practical relevance for applications in storm surge risk analysis and flood management.

Historical analysis of Newfoundland dog fur colour genetics

PubMed Central

Bondeson, J.

2015-01-01

This article makes use of digitized historic newspapers to analyze Newfoundland dog fur colour genetics, and fur colour variations over time. The results indicate that contrary to the accepted view, the ‘Solid’ gene was introduced into the British population of Newfoundland dogs in the 1840s. Prior to that time, the dogs were white and black (Landseer) or white and brown, and thus spotted/spotted homozygotes. Due to ‘Solid’ being dominant over ‘spotted’, and selective breeding, today the majority of Newfoundland dogs are solid black. Whereas small white marks on the chest and/or paw appears to be a random event, the historical data supports the existence of an ‘Irish spotted’ fur colour pattern, with white head blaze, breast, paws and tail tip, in spotted/spotted homozygotes. PMID:26623371

FORMATION OF CHLOROPYROMORPHITE IN A LEAD-CONTAMINATED SOIL AMENDED WITH HYDROXYAPATITE

EPA Science Inventory

To evaluate conversion of soil Pb to pyromorphite, a Pb contaminated soil collected adjacent to a historical smelter was reacted with hydroxyapatite in a traditional incubation experiment and in a dialysis system in which the soil and hydroxyapatite solids were separated by a dia...

Proceed with Caution! Braking the Liability Cycle with Solid Partnerships.

ERIC Educational Resources Information Center

Delaney, David P., Jr.

1988-01-01

Historically, the insurance industry has been cyclical in price and the types of risks it will insure. Schools should carefully consider developing long-term relationships with companies committed to school bus insurance. Buyers can exchange information with their insurers to improve their risks. (MLF)

A Course on the Physics and Chemistry of Pollution

ERIC Educational Resources Information Center

Hodges, Laurent

1971-01-01

Describes a course on environmental pollution which stresses physical and chemical principles. Course presents a unified discussion of air and water pollution and solid waste with special treatment of pesticides, thermal pollution, radioactivity, and electric power generation. Uses historical and current statistics extensively to set pollution…

SEWER-SEDIMENT CONTROL: OVERVIEW OF AN EPA WET-WEATHER FLOW RESEARCH PROGRAM

EPA Science Inventory

This paper presents a historical overview of the sewer sediment control projects conducted by the Wet-Weather Flow Research Program of the USEPA. Research presented includes studies of the causes of sewer solids deposition and development/evaluation of control methods that can pr...

Groundwater's significance to changing hydrology, water chemistry, and biological communities of a floodplain ecosystem, Everglades, South Florida, USA

USGS Publications Warehouse

Harvey, J.W.; McCormick, P.V.

2009-01-01

The Everglades (Florida, USA) is one of the world's larger subtropical peatlands with biological communities adapted to waters low in total dissolved solids and nutrients. Detecting how the pre-drainage hydrological system has been altered is crucial to preserving its functional attributes. However, reliable tools for hindcasting historic conditions in the Everglades are limited. A recent synthesis demonstrates that the proportion of surface-water inflows has increased relative to precipitation, accounting for 33% of total inputs compared with 18% historically. The largest new source of water is canal drainage from areas of former wetlands converted to agriculture. Interactions between groundwater and surface water have also increased, due to increasing vertical hydraulic gradients resulting from topographic and water-level alterations on the otherwise extremely flat landscape. Environmental solute tracer data were used to determine groundwater's changing role, from a freshwater storage reservoir that sustained the Everglades ecosystem during dry periods to a reservoir of increasingly degraded water quality. Although some of this degradation is attributable to increased discharge of deep saline groundwater, other mineral sources such as fertilizer additives and peat oxidation have made a greater contribution to water-quality changes that are altering mineral-sensitive biological communities. ?? Springer-Verlag 2008.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shekiro, III, Joseph; Chen, Xiaowen; Smith, Holly

Dilute-acid pretreatment has proven to be a robust means of converting herbaceous feedstock to fermentable sugars. However, it also releases acetic acid, a known fermentation inhibitor, from acetyl groups present in the biomass. A mild, dilute alkaline extraction stage was implemented prior to acid pretreatment to separate acetic acid from the hydrolysate sugar stream. This step, termed deacetylation, improved the glucose and xylose yields from enzymatic hydrolysis and ethanol yields from fermentation of the sugars relative to the control experiments using dilute-acid pretreatment of native corn stover without deacetylation. While promising, deacetylation as it was historically practiced is conducted atmore » low solids loadings, and at fixed conditions. Thus, many questions have been left unanswered, including the relationship between sodium hydroxide and solids loading, and acetate and xylan solubilization, as well as the impact of temperature and residence time on the process efficacy. A central composite experiment was designed to evaluate the impact of solids loading, sodium hydroxide loading, reaction time and temperature during deacetylation on the acetate and xylan solubilization of corn stover. Using the ANOVA test, it became apparent that neither of the responses was significantly impacted by the solids loading, while the reaction time was a minor factor - the responses were largely driven by reaction temperature and the sodium hydroxide loading. Based on the results, we successfully demonstrated the ability to transition the low-solids (10 % w/w) deacetylation process to a higher-solids process (30 % w/w) with minimal impact on the ability to extract acetate from biomass. Conditions were selected to minimize xylose loss during deacetylation, while also removing 70 % of acetyl groups. The impact of selected conditions on the enzymatic hydrolysis and fermentation was further investigated. In conclusion, evaluation of the whole-process impact demonstrated that despite the upfront reduction in carbohydrate loss during deacetylation, the overall process sugar yields were depressed by the high-solids, low alkali process relative to the historical control. Consequently, ethanol titers were reduced, though strong fermentation performance was still observed, indicating that 70 % acetate removal is sufficient to depress acetic acid concentrations to a level that does not substantially inhibit ethanol fermentation by rZymomo nas.« less

Progression towards optimization of viscosity of highly concentrated carbonaceous solid-water slurries by incorporating and modifying surface chemistry parameters with and without additives

NASA Astrophysics Data System (ADS)

Mukherjee, Amrita

Carbonaceous solid-water slurries (CSWS) are concentrated suspensions of coal, petcoke bitumen, pitch etc. in water which are used as feedstock for gasifiers. The high solid loading (60-75 wt.%) in the slurry increases CSWS viscosity. For easier handling and pumping of these highly loaded mixtures, low viscosities are desirable. Depending on the nature of the carbonaceous solid, solids loading in the slurry and the particle size distribution, viscosity of a slurry can vary significantly. Ability to accurately predict the viscosity of a slurry will provide a better control over the design of slurry transport system and for viscosity optimization. The existing viscosity prediction models were originally developed for hard-sphere suspensions and therefore do not take into account surface chemistry. As a result, the viscosity predictions using these models for CSWS are not very accurate. Additives are commonly added to decrease viscosity of the CSWS by altering the surface chemistry. Since additives are specific to CSWS, selection of appropriate additives is crucial. The goal of this research was to aid in optimization of CSWS viscosity through improved prediction and selection of appropriate additive. To incorporate effect of surface chemistry in the models predicting suspension viscosity, the effect of the different interfacial interactions caused by different surface chemistries has to be accounted for. Slurries of five carbonaceous solids with varying O/C ratio (to represent different surface chemistry parameters) were used for the study. To determine the interparticle interactions of the carbonaceous solids in water, interfacial energies were calculated on the basis of surface chemistries, characterized by contact angles and zeta potential measurements. The carbonaceous solid particles in the slurries were assumed to be spherical. Polar interaction energy (hydrophobic/hydrophilic interaction energy), which was observed to be 5-6 orders of magnitude higher than the electrostatic interaction energy, and the van der Waals interaction energy, was clearly the dominant interaction energy for such a system. Hydrophobic interactions lead to the formation of aggregation networks of solids in the suspensions, entrapping a part of the bulk water, whereas hydrophilic interactions result in the formation of hydration layers around carbonaceous solids. Both of these phenomena cause a loss of bulk water from the slurry and increase the effective solid volume fraction, resulting in an increase in slurry viscosity. The water in the bulk of the slurry, responsible for the fluidity of the slurry is called free water. The amount of free water was determined using thermogravimetric analysis and was observed to increase with an increase in the O/C ratio of a carbonaceous solid (up to ˜20%). The free water to total water ratio was observed to be constant for the slurry of a particular carbonaceous solid for various loadings of solids (44 wt.% to 67 wt.%). The increase in the effective solid volume fractions of slurries was determined using viscosity measurements. A relationship between the effective solid volume fraction and the O/C ratio of the carbonaceous solid was developed. This correlation was then incorporated into the existing equation for viscosity prediction (developed based on particle size distribution and solid volume fraction), to account for the surface chemistry of the carbonaceous solid and hence improve the predictive capabilities. This modified equation was validated using three concentrated carbonaceous slurries with different particle size distributions and was observed to significantly improve accuracy of prediction (deviation of predicted results decreased from up to 96% to 25%). The validation was performed with a lignite, bituminous coal and a petcoke-all with low ash yield. Additives modify the surface chemistry of the carbonaceous solids, thereby affecting the interfacial interactions. Through this research, the effects of additives on the interfacial interactions and hence on slurry viscosity were determined. Since the additives used are specific to the surface chemistry of the solids in the slurry, this knowledge aids in the selection of the appropriate additive. The study was conducted using three carbonaceous solids with different O/C ratios and an anionic and a non-ionic additive. The adsorption of the additives on the carbonaceous solids, the change in the zeta potential and hydrophobicity/hydrophilicity of the solids and the change in the free water content of the slurries were determined. The adsorption of the additives increased with an increase in the mineral matter content of the carbonaceous solids. There was also an increase in the zeta potential of the carbonaceous solids in water upon the addition of the anionic additive (up to ˜30%). However, the calculated resultant electrostatic repulsion energy upon the addition of the anionic additive was 5-6 orders of magnitude lower than the polar interaction energy of the carbonaceous solids in water. Contact angle measurements indicated that both additives changed the hydrophobicity/hydrophilicity of the solid surface (by up to 70°). This resulted in the release of bound water into the bulk slurries (up to 6%), resulting in greater fluidity. The increase in free water content of the slurries with additives was confirmed by thermogravimetric analysis (TGA). A correlation predicting the slurry viscosity on the basis of the weight fraction of free water in the slurries with additives was also developed.

NASA's Software Bank (CLIPS)

NASA Technical Reports Server (NTRS)

1991-01-01

C Language Integrated Production System (CLIPS) is a NASA Johnson Space Center developed software shell for developing expert systems, is used by researchers at Ohio State University to determine solid waste disposal sites to assist in historic preservation. The program has various other applications and has even been included in a widely-used textbook.

Contemporary Readings in Curriculum

ERIC Educational Resources Information Center

Stern, Barbara Slater; Kysilka, Marcella L.

2008-01-01

This book provides beginning teachers and educational leaders with a series of articles that can help them build their curriculum knowledge base. Features include: (1) Provides a historical context of the curriculum field, giving educators a solid foundation for curriculum knowledge; (2) Describes the political nature of curriculum and how we must…

The Recovery of Energy from Waste.

ERIC Educational Resources Information Center

Baxter, Zeland L.; And Others

This study unit advocates the use of biomass conversion techniques with municipal solid wastes as a viable action for energy development. The unit includes: (1) an introductory section (providing a unit overview and supportive statements for biomass conversion; (2) a historical review of energy use from wastes; (3) a section on design and…

76 FR 12787 - Office of Commercial Space Transportation; Notice of Availability of the Final Environmental...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-08

... scenarios (land, air, and sea). The Pegasus launch vehicle falls within the parameters of the small-payload... quality; biological resources (including fish, wildlife, and plants); compatible land use; Department of Transportation Section 4(f) resources; hazardous materials, pollution prevention, and solid waste; historical...

Measuring solids concentration in stormwater runoff: comparison of analytical methods.

PubMed

Clark, Shirley E; Siu, Christina Y S

2008-01-15

Stormwater suspended solids typically are quantified using one of two methods: aliquot/subsample analysis (total suspended solids [TSS]) or whole-sample analysis (suspended solids concentration [SSC]). Interproject comparisons are difficult because of inconsistencies in the methods and in their application. To address this concern, the suspended solids content has been measured using both methodologies in many current projects, but the question remains about how to compare these values with historical water-quality data where the analytical methodology is unknown. This research was undertaken to determine the effect of analytical methodology on the relationship between these two methods of determination of the suspended solids concentration, including the effect of aliquot selection/collection method and of particle size distribution (PSD). The results showed that SSC was best able to represent the known sample concentration and that the results were independent of the sample's PSD. Correlations between the results and the known sample concentration could be established for TSS samples, but they were highly dependent on the sample's PSD and on the aliquot collection technique. These results emphasize the need to report not only the analytical method but also the particle size information on the solids in stormwater runoff.

Quality of ground water in the Columbia Basin, Washington, 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turney, G.L.

1986-01-01

Groundwater from 188 sites in the Columbia Basin of central Washington was sampled and analyzed in 1983 for pH, specific conductance, and concentrations of fecal coliform bacteria, major dissolved ions, and dissolved iron, manganese, and nitrate. Twenty of the samples were also analyzed for concentrations of dissolved trace metals including aluminum, arsenic, barium, cadmium, chromium, copper, lead, mercury, selenium, silver, and zinc. The predominant water types were sodium bicarbonate and calcium bicarbonate. The sodium bicarbonate water samples had higher pH, fluoride, and sodium:adsorption ratio values than samples with other water types. Most trace metal concentrations were also < 10 ug/Lmore » except for barium and zinc, which had maximum concentrations of 170 and 600 ug/L, respectively. Nitrate concentrations were < 1.0 mg/L in water from more than half the wells sampled. US EPA (Environmental Protection Agency) drinking water regulations were exceeded in several samples, most commonly involving pH and concentrations of fluoride, nitrate, and dissolved solids in samples from Adams and Grant Counties. Generally, the historical data lead to similar conclusions about the quality of groundwater in the Columbia Basin region. However, historical samples had higher dissolved solids concentrations in Douglas County. Historical samples also included fewer sodium bicarbonate type waters in the region as a whole than the 1983 samples. 24 refs., 2 figs., 4 tabs.« less

Barcelona Rocks, a mobile app to learn geology in your city

NASA Astrophysics Data System (ADS)

Geyer, Adelina; Cabrera, Lluis; Alias, Gemma; Aulinas, Meritxell; Becerra, Margarita; Casadellà, Jordi; Clotet, Roger; Delclós, Xavier; Fernández-Turiel, José-Luis; Tarragó, Marta; Travé, Anna

2016-04-01

Barcelona Rocks is an application for personal mobile devices suitable for secondary and high school students as well as the general public without a solid background in Earth Sciences. The main objective of this app is to teach Geology using as learning resource our city façades and pavements. Additionally, Barcelona Rocks provides a short explanation about the significance of the appearance of the different rock types at the different historical periods of the city. Although it has been designed as a playful learning resource for secondary school students, the level of knowledge also allows bringing some basic concepts and principles of Earth Sciences to the general public, irrespective of age. This app is intended to provide the degree of interactivity and entertainment required by the different individual users and aims to: (i) Explain the techniques and experiments that allow the user to identify the different rocks, as well as their genesis. (ii) Introduce geology to the youngest users in a more attractive and entertaining way, providing also some information regarding the use of the different ornamental rocks during the different historical periods of the city: roman, medieval, etc. (iii) Provide historical and architectural information of the selected buildings in order to improve the city's historical architectural knowledge of the users. (iv) Show the non-expert public the importance of their country's geology. (v) Develop of outreach and dissemination resources taking advantage of the versatile and potent mobile application format using also the content as support material for science courses, seminars, or social learning events. (vi) Encourage new generations of Earth Scientists (vii) Promote science and scientific culture of the society, integrating culture and innovation as essential for the emergence of new scientific and technological vocations, promoting critical thinking, understanding of the scientific method and the social interest in science, technology and innovation.

Documentation for Preservation: Methodology and a GIS Database of Three World Heritage Cities in Uzbekistan

NASA Astrophysics Data System (ADS)

Vileikis, O.; Escalante Carrillo, E.; Allayarov, S.; Feyzulayev, A.

2017-08-01

The historic cities of Uzbekistan are an irreplaceable legacy of the Silk Roads. Currently, Uzbekistan counts with four UNESCO World Heritage Properties, with hundreds of historic monuments and traditional historic houses. However, lack of documentation, systematic monitoring and a digital database, of the historic buildings and dwellings within the historic centers, are threatening the World Heritage properties and delaying the development of a proper management mechanism for the preservation of the heritage and an interwoven city urban development. Unlike the monuments, the traditional historic houses are being demolished without any enforced legal protection, leaving no documentation to understand the city history and its urban fabric as well of way of life, traditions and customs over the past centuries. To fill out this gap, from 2008 to 2015, the Principal Department for Preservation and Utilization of Cultural Objects of the Ministry of Culture and Sports of Uzbekistan with support from the UNESCO Office in Tashkent, and in collaboration with several international and local universities and institutions, carried out a survey of the Historic Centre of Bukhara, Itchan Kala and Samarkand Crossroad of Cultures. The collaborative work along these years have helped to consolidate a methodology and to integrate a GIS database that is currently contributing to the understanding of the outstanding heritage values of these cities as well as to develop preservation and management strategies with a solid base of heritage documentation.

Comparability and accuracy of fluvial-sediment data - A view from the U.S. Geological Survey

USGS Publications Warehouse

Gray, J.R.; Glysson, G.D.; Mueller, D.S.; ,

2002-01-01

The quality of historical fluvial-sediment data cannot be taken for granted, based on a review of upper Colorado River basin suspended-sediment discharges, and on an evaluation of the reliability of Total Suspended Solids (TSS) data. Additionally, the quality of future fluvial-sediment data are not assured. Sediment-surrogate technologies, including those that operate on acoustic, laser, bulk optic, digital optic, or pressure differential principles, are being used with increasing frequency to measure in-stream and (or) laboratory fluvial-sediment characteristics. Data from sediment-surrogate technologies may yield results that differ significantly from those obtained by traditional methods for the same sedimentary conditions. Development of national sediment data-quality criteria and rigorous comparisons of data derived from sediment-surrogate technologies to those obtained by traditional techniques will minimize the potential for future fluvial-sediment data-quality concerns.

Fruit Juice in Infants, Children, and Adolescents: Current Recommendations.

PubMed

Heyman, Melvin B; Abrams, Steven A

2017-06-01

Historically, fruit juice was recommended by pediatricians as a source of vitamin C and as an extra source of water for healthy infants and young children as their diets expanded to include solid foods with higher renal solute load. It was also sometimes recommended for children with constipation. Fruit juice is marketed as a healthy, natural source of vitamins and, in some instances, calcium. Because juice tastes good, children readily accept it. Although juice consumption has some benefits, it also has potential detrimental effects. High sugar content in juice contributes to increased calorie consumption and the risk of dental caries. In addition, the lack of protein and fiber in juice can predispose to inappropriate weight gain (too much or too little). Pediatricians need to be knowledgeable about juice to inform parents and patients on its appropriate uses. Copyright © 2017 by the American Academy of Pediatrics.

Arsenic solid-phase speciation and reversible binding in long-term contaminated soils.

PubMed

Rahman, M S; Clark, M W; Yee, L H; Comarmond, M J; Payne, T E; Kappen, P; Mokhber-Shahin, L

2017-02-01

Historic arsenic contamination of soils occurs throughout the world from mining, industrial and agricultural activities. In Australia, the control of cattle ticks using arsenicals from the late 19th to mid 20th century has led to some 1600 contaminated sites in northern New South Wales. The effect of aging in As-mobility in two dip-site soil types, ferralitic and sandy soils, are investigated utilizing isotopic exchange techniques, and synchrotron X-ray adsorption spectroscopy (XAS). Findings show that historic soil arsenic is highly bound to the soils with >90% irreversibly bound. However, freshly added As (either added to historically loaded soils or pristine soils) has a significantly higher degree of As-accessibility. XAS data indicates that historic soil arsenic is dominated as Ca- (svenekite, & weilite), Al-(mansfieldite), and Fe- (scorodite) like mineral precipitates, whereas freshly added As is dominated by mineral adsorption surfaces, particularly the iron oxy-hydroxides (goethite and hematite), but also gibbsite and kaolin surfaces. SEM data further confirmed the presence of scorodite and mansfieldite formation in the historic contaminated soils. These data suggest that aging of historic soil-As has allowed neoformational mineral recrystallisation from surface sorption processes, which greatly reduces As-mobility and accessibility. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of solid-phase microextraction with gas chromatography and mass spectrometry for the early detection of active moulds on historical woollen objects.

PubMed

Sawoszczuk, Tomasz; Syguła-Cholewińska, Justyna; Del Hoyo-Meléndez, Julio M

2017-02-01

The goal of this work was to determine the microbial volatile organic compounds emitted by moulds growing on wool in search of particular volatiles mentioned in the literature as indicators of active mould growth. The keratinolytically active fungi were inoculated on two types of media: (1) samples of wool placed on broths, and (2) on broths containing amino acids that are elements of the structure of keratin. All samples were prepared inside 20 mL vials (closed system). In the first case (1) the broths did not contain any sources of organic carbon, nitrogen, or sulfur, i.e. wool was the only nutrient for the moulds. A third type of sample was historical wool prepared in a Petri dish without a broth and inoculated with a keratinolytically active mould (open system). The microbial volatiles emitted by moulds were sampled with the headspace solid-phase microextraction method. Volatiles extracted on solid-phase microextraction fibers were analyzed in a gas chromatography with mass spectrometry system. Qualitative and quantitative analyses of chromatograms were carried out in search of indicators of metabolic activity. The results showed that there are three groups of volatiles that can be used for the detection of active forms of moulds on woollen objects. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Kinetic concepts of thermally stimulated reactions in solids

NASA Astrophysics Data System (ADS)

Vyazovkin, Sergey

Historical analysis suggests that the basic kinetic concepts of reactions in solids were inherited from homogeneous kinetics. These concepts rest upon the assumption of a single-step reaction that disagrees with the multiple-step nature of solid-state processes. The inadequate concepts inspire such unjustified anticipations of kinetic analysis as evaluating constant activation energy and/or deriving a single-step reaction mechanism for the overall process. A more adequate concept is that of the effective activation energy, which may vary with temperature and extent of conversion. The adequacy of this concept is illustrated by literature data as well as by experimental data on the thermal dehydration of calcium oxalate monohydrate and thermal decomposition of calcium carbonate, ammonium nitrate and 1,3,5,7- tetranitro-1,3,5,7-tetrazocine.

Rentz's Student Affairs Practice in Higher Education. Fourth Edition

ERIC Educational Resources Information Center

Zhang, Naijian

2011-01-01

The mission of this new fourth edition is to provide the reader with a solid foundation in the historical and philosophical perspectives of college student affairs development; assist the reader in understanding the major concepts and purpose of student affairs' practice, methods, and program models; enable the reader to conceptualize the theme,…

Polyhedron Models for the Classroom. Second Edition.

ERIC Educational Resources Information Center

Wenninger, Magnus J.

This second edition explains the historical background and techniques for constructing various types of polyhedra. Seven center-fold sheets are included, containing full-scale drawings from which nets or templates may be made to construct the models shown and described in the text. Details are provided for construction of the five Platonic solids,…

Stories of Discovery Stimulate the Physics Major--A Polemic, with Examples.

ERIC Educational Resources Information Center

Leitner, Alfred

1980-01-01

Provides historical examples of intuitive discovery applicable to the teaching of physics for majors. Cites details for the discovery of Coulomb's law, emphasizing the roles of Joseph Priestley and Henry Cavendish. Also discusses the career of Ivar Giaever, a Nobel Prize winner of 1973 in solid state physics. (CS)

Riding the Juggernaut in the Risk Society

ERIC Educational Resources Information Center

Child & Youth Services, 2007

2007-01-01

There are irreconcilable and contested positions taken around the definition and understanding of risk. The purpose of this chapter is to locate risk discourse more solidly in a social scientific framework by providing an historical analysis of literature dealing with risk drawing from the fields of risk assessment and, later, the social sciences…

The Bisagno stream catchment (Genoa, Italy) and its major floods: geomorphic and land use variations in the last three centuries

NASA Astrophysics Data System (ADS)

Faccini, Francesco; Paliaga, Guido; Piana, Pietro; Sacchini, Alessandro; Watkins, Charles

2016-11-01

The city of Genoa (Liguria, Italy) and the Bisagno Valley are affected by frequent floods, often with loss of human lives. Historically characterised by high flood hazards, the Bisagno Valley was recently affected by a flood event on 9 October 2014, less than three years after the tragic flood event of 4 November 2011 when six people died, including two children. In the last 50 years, four destructive floods occurred in the Bisagno Valley, in addition to some other events that caused significant damage and economic losses. This paper examines the three largest flood events in terms of intensity and ground effects which affected the Bisagno Valley in the last three centuries: the flood of 25 October 1822, well documented by contemporary sources, the flood of 8 October 1970, undoubtedly the most tragic on record, and the very recent event of 9 October 2014. For this purpose scientific and historical-geographical methodologies were adopted, the latter particularly useful for the reconstruction of the flood event of 1822 and the landscape history of the Bisagno Valley in the nineteenth century. This comparison shows that the Bisagno Valley is characterised by climatic and landform features that have been making the flood events historically common in the area. However, recent climate change and land-use variations, including some major modifications of the catchment basin, have progressively determined a decrease of the concentration time and an increase of runoff, solid transport, and flood hazard. Consequently, in recent decades a growth in the number of flood events occurred, to the extent that the Bisagno today is a famous case study on an international scale.

Historically Black Colleges and Universities: Honoring the Past, Engaging the Present, Touching the Future

ERIC Educational Resources Information Center

Allen, Walter R.; Jewell, Joseph O.; Griffin, Kimberly A.; Wolf, De'Sha S.

2007-01-01

This article examines the history, present, and future of historically Black colleges and universities (HBCUs). We begin with a brief review of the existing literature on HBCUs, considering common themes and how these institutions changed over time within a broader socio-historical landscape. In addition to historical information, we use a…

Solidification and solid-state transformation sciences in metals additive manufacturing

DOE PAGES

Kirka, Michael M.; Nandwana, Peeyush; Lee, Yousub; ...

2017-02-11

Additive manufacturing (AM) of metals is rapidly emerging as an established manufacturing process for metal components. Unlike traditional metals fabrication processes, metals fabricated via AM undergo localized thermal cycles during fabrication. As a result, AM presents the opportunity to control the liquid-solid phase transformation, i.e. material texture. But, thermal cycling presents challenges from the standpoint of solid-solid phase transformations. We will discuss the opportunities and challenges in metals AM in the context of texture control and associated solid-solid phase transformations in Ti-6Al-4V and Inconel 718.

36 CFR 6.6 - Solid waste disposal sites within new additions to the National Park System.

Code of Federal Regulations, 2012 CFR

2012-07-01

... within new additions to the National Park System. 6.6 Section 6.6 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SOLID WASTE DISPOSAL SITES IN UNITS OF THE NATIONAL PARK SYSTEM § 6.6 Solid waste disposal sites within new additions to the National Park System. (a) An operator...

36 CFR 6.6 - Solid waste disposal sites within new additions to the National Park System.

Code of Federal Regulations, 2014 CFR

2014-07-01

... within new additions to the National Park System. 6.6 Section 6.6 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SOLID WASTE DISPOSAL SITES IN UNITS OF THE NATIONAL PARK SYSTEM § 6.6 Solid waste disposal sites within new additions to the National Park System. (a) An operator...

36 CFR 6.6 - Solid waste disposal sites within new additions to the National Park System.

Code of Federal Regulations, 2013 CFR

2013-07-01

... within new additions to the National Park System. 6.6 Section 6.6 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SOLID WASTE DISPOSAL SITES IN UNITS OF THE NATIONAL PARK SYSTEM § 6.6 Solid waste disposal sites within new additions to the National Park System. (a) An operator...

36 CFR 6.6 - Solid waste disposal sites within new additions to the National Park System.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Solid waste disposal sites... NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SOLID WASTE DISPOSAL SITES IN UNITS OF THE NATIONAL PARK SYSTEM § 6.6 Solid waste disposal sites within new additions to the National Park System. (a) An operator...

36 CFR 6.6 - Solid waste disposal sites within new additions to the National Park System.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Solid waste disposal sites... NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR SOLID WASTE DISPOSAL SITES IN UNITS OF THE NATIONAL PARK SYSTEM § 6.6 Solid waste disposal sites within new additions to the National Park System. (a) An operator...

Surface Wetting-Driven Separation of Surfactant-Stabilized Water-Oil Emulsions.

PubMed

Zhang, Qian; Li, Lei; Li, Yanxiang; Cao, Lixia; Yang, Chuanfang

2018-05-15

Four fluorocarbon polymers including polytetrafluoroethylene and polyvinylidene fluoride were coated on a stainless steel felt to separate emulsified water droplets from ultralow sulfur diesel (ULSD) fuels. The original fuel treated with clay to remove additives was additized again with four known surfactants including pentaerythrityoleate, (octadecadienoic acid) dipolymer, (octadecadienoic acid) tripolymer, and monoolein individually. The different surfactants adsorbed on the fuel-water interface reduce the interfacial intension with different intensities. The separation efficiency at various surfactant concentrations was used to evaluate the coalescence effect exerted by these coatings. It was found the separation was both surfactant- and coating-dependent. A fluoro-polyurethane coating (FC1) stood out to counteract the adverse effect of all the surfactants. Solid free energy was then measured using acid-base and Kaelble-Uy adhesion theories for all the coatings, but its correlation with coalescence was not found at all. Coating aging in surfactant-additized fuel on the coating's water wettability was also examined to better understand how historical wetting affects separation. A tumbled model for fluorocarbons was identified that well-explained the continuous decline of the water contact angle on the FC1 coating in fuel. Subject to the challenge of the foreign environment, the fluoroalkyl chains of the polymer tilt to expose the carbonyl groups underneath, resulting in favored coalescence separation in the presence of surfactants.

Analysis of quasi-hybrid solid rocket booster concepts for advanced earth-to-orbit vehicles

NASA Technical Reports Server (NTRS)

Zurawski, Robert L.; Rapp, Douglas C.

1987-01-01

A study was conducted to assess the feasibility of quasi-hybrid solid rocket boosters for advanced Earth-to-orbit vehicles. Thermochemical calculations were conducted to determine the effect of liquid hydrogen addition, solids composition change plus liquid hydrogen addition, and the addition of an aluminum/liquid hydrogen slurry on the theoretical performance of a PBAN solid propellant rocket. The space shuttle solid rocket booster was used as a reference point. All three quasi-hybrid systems theoretically offer higher specific impulse when compared with the space shuttle solid rocket boosters. However, based on operational and safety considerations, the quasi-hybrid rocket is not a practical choice for near-term Earth-to-orbit booster applications. Safety and technology issues pertinent to quasi-hybrid rocket systems are discussed.

12. HISTORICAL VIEW OF FRONT ENTRANCE, BEFORE ADDITION OF SHELTERED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. HISTORICAL VIEW OF FRONT ENTRANCE, BEFORE ADDITION OF SHELTERED PORCH, SOUTH ELEVATION, 1907. Photocopied from Henry Pleasants's book, History of Old St. David's Church, published in 1915 by John C. Winston Co. - St. David's Church (Episcopal), Valley Forge Road (Newtown Township), Wayne, Delaware County, PA

Cross National Comparisons of Excellence in University Mathematics Instructors

ERIC Educational Resources Information Center

Grant, Frida

2014-01-01

Mathematicians have, historically, not been overly successful in their approach to teaching and much research has looked in to why this is so. Teaching mathematics is based on a solid understanding of the subject; however, instructors also need to be able to efficiently communicate the subject to their students. The purpose of this study was to…

Glass Doesn't Flow and Doesn't Crystallize and It Isn't a Liquid.

ERIC Educational Resources Information Center

Hawkes, Stephen J.

2000-01-01

Illustrates that, contrary to some assertions made in the popular press, scientific literature, and introductory textbooks, glass does not flow in historic time. Contends that glass is a rigid solid with a lower degree of molecular order than a crystal but with greater molecular order than a liquid. (Contains 27 references.) (WRM)

Water quality of the lower Columbia River basin; analysis of current and historical water-quality data through 1994

USGS Publications Warehouse

Fuhrer, Gregory J.; Tanner, Dwight Q.; Morace, Jennifer L.; McKenzie, Stuart W.; Skach, Kenneth A.

1996-01-01

Trend tests showed significant (r < 0.05) downward trends from 1973 to 1994 for three constituents at the Columbia River at Warrendale: phosphorus in unfiltered water, total dissolved solids, and specific conductance. These trends may be a consequence of more conservative agricultural practices in the area upstream from Warrendale.

The Physics Teacher: The Four States of Matter—Solid, Squishy, Liquid, and Gas

NASA Astrophysics Data System (ADS)

Clark, Roy W.

2007-04-01

The featured article offers several demonstrations of substances that seem to be neither solid nor liquid, but somewhere in between. The authors suggest laboratory experiments that can be performed by beginning physics students, and suggest theoretical explanations for the strange viscosity behaviors. The subject is chemistry much more than physics, and it may require chemistry textbook authors to rethink the popular definitions of physical and chemical change. This reviewer then comments on the historical origins of squishiness, and on its unfortunate neglect, in their author's opinion, by general chemistry texts. The subject is properly called rheology, and is of considerable significance to industrial chemists.

Japanese experiences of environmental management.

PubMed

Matsuo, T

2003-01-01

Japan experienced a very rapid industrialization and economic growth in the era of income doubling in 1960s and at the same time Japan experienced very severe damage from various types of environmental pollution. In this paper, historical development of population, GNP, energy consumption with classification of petroleum, coal and electric power, and CO2 emission are introduced as basic background data on Japanese development. The tragic experience of Minamata disease and Itai-itai disease caused by methyl mercury and cadmium, respectively, are introduced. In two tables, historical development of water pollution and air pollution are summarized. Regarding solid wastes management, the total mass balance in Japan and recent development in legislation framework for enhancement of recycling of wastes are introduced briefly.

Scale-up and process integration of sugar production by acidolysis of municipal solid waste/corn stover blends in ionic liquids.

PubMed

Li, Chenlin; Liang, Ling; Sun, Ning; Thompson, Vicki S; Xu, Feng; Narani, Akash; He, Qian; Tanjore, Deepti; Pray, Todd R; Simmons, Blake A; Singh, Seema

2017-01-01

Lignocellulosic biorefineries have tonnage and throughput requirements that must be met year round and there is no single feedstock available in any given region that is capable of meeting the price and availability demands of the biorefineries scheduled for deployment. Significant attention has been historically given to agriculturally derived feedstocks; however, a diverse range of wastes, including municipal solid wastes (MSW), also have the potential to serve as feedstocks for the production of advanced biofuels and have not been extensively studied. In addition, ionic liquid (IL) pretreatment with certain ILs is receiving great interest as a potential process that enables fractionation of a wide range of feedstocks. Acid catalysts have been used previously to hydrolyze polysaccharides into fermentable sugars following IL pretreatment, which could potentially provide a means of liberating fermentable sugars from lignocellulose without the use of costly enzymes. However, successful optimization and scale-up of the one-pot acid-assisted IL deconstruction for further commercialization involve challenges such as reactor compatibility, mixing at high solid loading, sugar recovery, and IL recycling, which have not been effectively resolved during the development stages at bench scale. Here, we present the successful scale-up demonstration of the acid-assisted IL deconstruction on feedstock blends of municipal solid wastes and agricultural residues (corn stover) by 30-fold, relative to the bench scale (6 vs 0.2 L), at 10% solid loading. By integrating IL pretreatment and acid hydrolysis with subsequent centrifugation and extraction, the sugar and lignin products can be further recovered efficiently. This scale-up development at Advanced Biofuels/Bioproducts Process Demonstration Unit (ABPDU) will leverage the opportunity and synergistic efforts toward developing a cost-effective IL-based deconstruction technology by drastically eliminating enzyme, reducing water usage, and simplifying the downstream sugar/lignin recovery and IL recycling. Results indicate that MSW blends are viable and valuable resource to consider when assessing biomass availability and affordability for lignocellulosic biorefineries. This scale-up evaluation demonstrates that the acid-assisted IL deconstruction technology can be effectively scaled up to larger operations and the current study established the baseline of scaling parameters for this process.

Development of the SoFAS (solid fats and added sugars) concept: the 2010 Dietary Guidelines for Americans.

PubMed

Nicklas, Theresa A; O'Neil, Carol E

2015-05-01

The diets of most US children and adults are poor, as reflected by low diet quality scores, when compared with the recommendations of the Dietary Guidelines for Americans (DGAs). Contributing to these low scores is that most Americans overconsume solid fats, which may contain saturated fatty acids and added sugars; although alcohol consumption was generally modest, it provided few nutrients. Thus, the 2005 DGAs generated a new recommendation: to reduce intakes of solid fats, alcohol, and added sugars (SoFAAS). What precipitated the emergence of the new SoFAAS terminology was the concept of discretionary calories (a "calorie" is defined as the amount of energy needed to increase the temperature of 1 kg of water by 1°C), which were defined as calories consumed after an individual had met his or her recommended nutrient intakes while consuming fewer calories than the daily recommendation. A limitation with this concept was that additional amounts of nutrient-dense foods consumed beyond the recommended amount were also considered discretionary calories. The rationale for this was that if nutrient-dense foods were consumed beyond recommended amounts, after total energy intake was met then this constituted excess energy intake. In the 2010 DGAs, the terminology was changed to solid fats and added sugars (SoFAS); thus, alcohol was excluded because it made a minor contribution to overall intake and did not apply to children. The SoFAS terminology also negated nutrient-dense foods that were consumed in amounts above the recommendations for the specific food groups in the food patterns. The ambiguous SoFAS terminology was later changed to "empty calories" to reflect only those calories from solid fats and added sugars (and alcohol if consumed beyond moderate amounts). The purpose of this review is to provide an historical perspective on how the dietary recommendations went from SoFAAS to SoFAS and how discretionary calories went to empty calories between the 2005 and 2010 DGAs. This information will provide practitioners, as well as the public, with valuable information to better understand the evolution of SoFAS over time. © 2015 American Society for Nutrition.

Development of the SoFAS (Solid Fats and Added Sugars) Concept: The 2010 Dietary Guidelines for Americans123

PubMed Central

Nicklas, Theresa A; O’Neil, Carol E

2015-01-01

The diets of most US children and adults are poor, as reflected by low diet quality scores, when compared with the recommendations of the Dietary Guidelines for Americans (DGAs). Contributing to these low scores is that most Americans overconsume solid fats, which may contain saturated fatty acids and added sugars; although alcohol consumption was generally modest, it provided few nutrients. Thus, the 2005 DGAs generated a new recommendation: to reduce intakes of solid fats, alcohol, and added sugars (SoFAAS). What precipitated the emergence of the new SoFAAS terminology was the concept of discretionary calories (a “calorie” is defined as the amount of energy needed to increase the temperature of 1 kg of water by 1°C), which were defined as calories consumed after an individual had met his or her recommended nutrient intakes while consuming fewer calories than the daily recommendation. A limitation with this concept was that additional amounts of nutrient-dense foods consumed beyond the recommended amount were also considered discretionary calories. The rationale for this was that if nutrient-dense foods were consumed beyond recommended amounts, after total energy intake was met then this constituted excess energy intake. In the 2010 DGAs, the terminology was changed to solid fats and added sugars (SoFAS); thus, alcohol was excluded because it made a minor contribution to overall intake and did not apply to children. The SoFAS terminology also negated nutrient-dense foods that were consumed in amounts above the recommendations for the specific food groups in the food patterns. The ambiguous SoFAS terminology was later changed to “empty calories” to reflect only those calories from solid fats and added sugars (and alcohol if consumed beyond moderate amounts). The purpose of this review is to provide an historical perspective on how the dietary recommendations went from SoFAAS to SoFAS and how discretionary calories went to empty calories between the 2005 and 2010 DGAs. This information will provide practitioners, as well as the public, with valuable information to better understand the evolution of SoFAS over time. PMID:25979510

Differences in dehydration tolerance among populations of a gametophyte-only fern.

PubMed

Chambers, Sally M; Watkins, J E; Sessa, Emily B

2017-04-01

For many plant species, historical climatic conditions may have left lasting imprints that are detectable in contemporary populations. Additionally, if these historical conditions also prevented gene flow among populations, these populations may be differentiated with respect to one another and their contemporary environmental conditions. For the fern, Vittaria appalachiana , one theory is that historical conditions during the Pleistocene largely shaped both the distribution and lack of sporophyte production. Our goals-based on this theory-were to examine physiological differences among and within populations spanning the species' geographic range, and the contribution of historical climatic conditions to this differentiation. We exposed explants from five populations to four drying treatments and examined differences in physiological response. Additionally, we examined the role of historical and current climatic conditions in driving the observed population differentiation. Populations differ in their ability to tolerate varying levels of dehydration, displaying a pattern of countergradient selection. Exposure to historical and contemporary climatic conditions, specifically variation in temperature and precipitation regimes, resulted in population divergence observed among contemporary populations. Historical conditions have shaped not only the distribution of V. appalachiana , but also its current physiological limitations. Results from this study support the hypothesis that climatic conditions during the Pleistocene are responsible for the distribution of this species, and may be responsible for the observed differences in dehydration tolerance. Additionally, dehydration tolerance may be the driving factor for previously reported patterns of countergradient selection in this species. © 2017 Botanical Society of America.

Understanding the Impact of Using Oral Histories in the Classroom

ERIC Educational Resources Information Center

Dutt-Doner, Karen M.; Allen, Susan; Campanaro, Kathryn

2016-01-01

Oral histories are a powerful pedagogical tool in developing historical understanding and important learning skills simultaneously. Teachers use firsthand accounts of historical time periods and/or events to help develop students' sense of history. In addition to gaining historical understanding, students are able to bring history alive by…

2. Historic American Buildings Survey Copy by Bert Shankland, Photographer ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Historic American Buildings Survey Copy by Bert Shankland, Photographer August 20, 1974 EAST AND SOUTH ELEVATION AFTER ADDITION OF PORCH, ALTERATION OF WINDOWS Fromthe Collection of the San Diego Historical Society, Serra Museum, San Diego - Temple Beth Israel, 1502 Second Avenue, San Diego, San Diego County, CA

Process for removal of mineral particulates from coal-derived liquids

DOEpatents

McDowell, William J.

1980-01-01

Suspended mineral solids are separated from a coal-derived liquid containing the solids by a process comprising the steps of: (a) contacting said coal-derived liquid containing solids with a molten additive having a melting point of 100.degree.-500.degree. C. in an amount of up to 50 wt. % with respect to said coal-derived liquid containing solids, said solids present in an amount effective to increase the particle size of said mineral solids and comprising material or mixtures of material selected from the group of alkali metal hydroxides and inorganic salts having antimony, tin, lithium, sodium, potassium, magnesium, calcium, beryllium, aluminum, zinc, molybdenum, cobalt, nickel, ruthenium, rhodium or iron cations and chloride, iodide, bromide, sulfate, phosphate, borate, carbonate, sulfite, or silicate anions; and (b) maintaining said coal-derived liquid in contact with said molten additive for sufficient time to permit said mineral matter to agglomerate, thereby increasing the mean particle size of said mineral solids; and (c) recovering a coal-derived liquid product having reduced mineral solids content. The process can be carried out with less than 5 wt. % additive and in the absence of hydrogen pressure.

Secondary STEM Education: "Designed by Apple in California, Assembled in China". The Progress of Education Reform. Volume 9, Number 4

ERIC Educational Resources Information Center

Zinth, Kyle

2008-01-01

America's advantage has historically been its people's creativity, flexibility and entrepreneurship. But just as painters need to be proficient in technique and theory to produce great masterpieces, the next generation of Americans will likely require a solid grounding in mathematics and science for their creativity to be maximized in a world…

METHOD 529, DETERMINATION OF EXPLOSIVES AND RELATED COMPOUNDS IN DRINKING WATER BY SOLID PHASE EXTRACTION AND CAPILLARY COLUMN GAS CHROMATOGRAPHY/MASS SPECTROMETRY

EPA Science Inventory

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) is a military explosive which is known to have contaminated groundwater on and near military installations where it has been used and stored. Historical disposal practices such as open burning and detonation have contributed to envir...

Student Services: A Handbook for the Profession. Third Edition. The Jossey-Bass Higher and Adult Education Series.

ERIC Educational Resources Information Center

Komives, Susan R.; Woodard, Dudley B., Jr.

A solid foundation in current literature in the field of student affairs is provided. New in this edition are an expanded theory section, expanded coverage of diversity issues, management and outcomes, and discussion of the impact of college on students. Part 1, "Historical Roots and Contemporary Context," includes chapters (1) "Historical…

Utilizing thin-film solid-phase extraction to assess the effect of organic carbon amendments on the bioavailability of DDT and dieldrin to earthworms

USDA-ARS?s Scientific Manuscript database

While DDT and dieldrin have been banned in most countries, contaminated agricultural sites exist in many areas and wildlife exposure is still of concern. Soil was obtained from a historical orchard that received routine pesticide applications more than 40 years ago. Bioavailability of DDT and diel...

Infrastructure Problems of the Cities of Developing Countries. An International Urbanization Survey Report to the Ford Foundation.

ERIC Educational Resources Information Center

Bernstein, Beverly, Ed.

The contents of this collaborative report are as follows: Chapter I--Terms of Reference. Chapter II--Historical Summary of Non-Research. Chapter III--Studies of Urban Infrastructure Elements: (A) Domestic Water Supply; (B) Removal and Treatment Solid and Liquid Wastes; (C) Domestic Power Supply; (D) Urban Transportation; (E) Urban Land. Chapter…

Historical Scientific Models and Theories as Resources for Learning and Teaching: The Case of Friction

ERIC Educational Resources Information Center

Besson, Ugo

2013-01-01

This paper presents a history of research and theories on sliding friction between solids. This history is divided into four phases: from Leonardo da Vinci to Coulomb and the establishment of classical laws of friction; the theories of lubrication and the Tomlinson's theory of friction (1850-1930); the theories of wear, the Bowden and Tabor's…

Historical Perspective and Contribution of U.S. Researchers Into the Field of Self-Propagating High-Temperature Synthesis (SHS)/Combustion Synthesis (CS): Personal Reflections

DTIC Science & Technology

2008-07-01

Gas - Solid Systems. Chem. Eng. Comm. 1990, 92, 199. 74. Dimitriou, P.; Puszynski, J. A.; Hlavacek, V. On the Dynamic of Equations Describing...Yu, L. H.; Thadani, N. N.; Meyers, M. A.; Graham, R. A.; Hammetter , W. F. Shock-Induced Chemical Synthesis of Intermetallic Compounds. In

Public-Private Hybridity in School Governance: A Solid Foundation or Developmental Process? Lessons from a Historical Analysis of Charter-Type Schools in Israel

ERIC Educational Resources Information Center

Bialik, Gadi

2014-01-01

Scholarly writing in the field of education policy analysis often considers two conflicting governance agendas: the social-democratic "public" agenda and the relatively young "neoliberal" governance agenda. These agendas are frequently described as being part of a process of transformation from public or state to private…

11. HISTORICAL VIEW OF CHURCH WITH ENCLOSED STAIRWAY ADDITION, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. HISTORICAL VIEW OF CHURCH WITH ENCLOSED STAIRWAY ADDITION, LOOKING NORTHWEST, 1850s. Photocopied from Henry Pleasants's book, History of Old St. David's Church, published in 1915 by John C. Winston Co. It is perhaps the earliest photograph of the church. - St. David's Church (Episcopal), Valley Forge Road (Newtown Township), Wayne, Delaware County, PA

Fifty years of solid-phase extraction in water analysis--historical development and overview.

PubMed

Liska, I

2000-07-14

The use of an appropriate sample handling technique is a must in an analysis of organic micropollutants in water. The efforts to use a solid phase for the recovery of analytes from a water matrix prior to their detection have a long history. Since the first experimental trials using activated carbon filters that were performed 50 years ago, solid-phase extraction (SPE) has become an established sample preparation technique. The initial experimental applications of SPE resulted in widespread use of this technique in current water analysis and also to adoption of SPE into standardized analytical methods. During the decades of its evolution, chromatographers became aware of the advantages of SPE and, despite many innovations that appeared in the last decade, new SPE developments are still expected in the future. A brief overview of 50 years of the history of the use of SPE in organic trace analysis of water is given in presented paper.

Past and Present Large Solid Rocket Motor Test Capabilities

NASA Technical Reports Server (NTRS)

Kowalski, Robert R.; Owen, David B., II

2011-01-01

A study was performed to identify the current and historical trends in the capability of solid rocket motor testing in the United States. The study focused on test positions capable of testing solid rocket motors of at least 10,000 lbf thrust. Top-level information was collected for two distinct data points plus/minus a few years: 2000 (Y2K) and 2010 (Present). Data was combined from many sources, but primarily focused on data from the Chemical Propulsion Information Analysis Center s Rocket Propulsion Test Facilities Database, and heritage Chemical Propulsion Information Agency/M8 Solid Rocket Motor Static Test Facilities Manual. Data for the Rocket Propulsion Test Facilities Database and heritage M8 Solid Rocket Motor Static Test Facilities Manual is provided to the Chemical Propulsion Information Analysis Center directly from the test facilities. Information for each test cell for each time period was compiled and plotted to produce a graphical display of the changes for the nation, NASA, Department of Defense, and commercial organizations during the past ten years. Major groups of plots include test facility by geographic location, test cells by status/utilization, and test cells by maximum thrust capability. The results are discussed.

Implementing Solar PV Projects on Historic Buildings and in Historic Districts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kandt, A.; Hotchkiss, E.; Walker, A.

Many municipalities, particularly in older communities of the United States, have a large amount of historic buildings and districts. In addition to preserving these historic assets, many municipalities have goals or legislative requirements to procure a certain amount of energy from renewable sources and to become more efficient in their energy use; often, these requirements do not exempt historic buildings. This paper details findings from a workshop held in Denver, Colorado, in June 2010 that brought together stakeholders from both the solar and historic preservation industries. Based on these findings, this paper identifies challenges and recommends solutions for developing solarmore » photovoltaic (PV) projects on historic buildings and in historic districts in such a way as to not affect the characteristics that make a building eligible for historic status.« less

University coal research/historically black colleges and universities and other minority institutions contractors review meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2006-07-01

A variety of papers/posters were presented on topics concerning power generation, including solid oxide fuel cells, hydrogen production, mercury as a combustion product, carbon dioxide separation from flue gas. A total of 31 presentations in slide/overview/viewgraph form and with a separate abstract are available online (one in abstract form only) and 24 poster papers (text). In addition 41 abstracts only are available. Papers of particular interest include: Hydrogen production from hydrogen sulfide in IGCC power plants; Oxidation of mercury in products of coal combustion; Computer aided design of advanced turbine aerofoil alloys for industrial gas turbines in coal fired environments;more » Developing engineered fuel using flyash and biomass; Conversion of hydrogen sulfide in coal gases to elemental sulfur with monolithic catalysts; Intelligent control via wireless sensor networks for advanced coal combustion systems; and Investment of fly ash and activated carbon obtained from pulverized coal boilers (poster).« less

76 FR 14069 - Notice of Inventory Completion: Office of the State Archaeologist, Michigan Historical Center...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-15

... mid-19th century Supervisor's House, a historic building in the park. In 2001, one additional bone was... House. It is uncertain if these remains are from the same individual, but the single additional bone may... that the 1986 fragments and 2001 bone belong to one individual. No known individual was identified. No...

A historical context of municipal solid waste management in the United States.

PubMed

Louis, Garrick E

2004-08-01

Municipal solid waste management (MSWM) in the United States is a system comprised of regulatory, administrative, market, technology, and social subcomponents, and can only be understood in the context of its historical evolution. American cities lacked organized public works for street cleaning, refuse collection, water treatment, and human waste removal until the early 1800s. Recurrent epidemics forced efforts to improve public health and the environment. The belief in anticontagionism led to the construction of water treatment and sewerage works during the nineteenth century, by sanitary engineers working for regional public health authorities. This infrastructure was capital intensive and required regional institutions to finance and administer it. By the time attention turned to solid waste management in the 1880s, funding was not available for a regional infrastructure. Thus, solid waste management was established as a local responsibility, centred on nearby municipal dumps. George Waring of New York City organized solid waste management around engineering unit operations; including street sweeping, refuse collection, transportation, resource recovery and disposal. This approach was adopted nationwide, and was managed by City Departments of Sanitation. Innovations such as the introduction of trucks, motorized street sweepers, incineration, and sanitary landfill were developed in the following decades. The Resource Conservation and Recovery Act of 1976 (RCRA), is the defining legislation for MSWM practice in America today. It forced the closure of open dumps nationwide, and required regional planning for MSWM. The closure of municipal dumps caused a 'garbage crisis' in the late 1980s and early 1990s. Private companies assumed an expanded role in MSWM through regional facilities that required the transportation of MSW across state lines. These transboundary movements of MSW created the issue of flow control, in which the US Supreme Court affirmed the protection of garbage under the Commerce Clause of the Constitution. Thus MSWM in America today is largely managed by municipalities, and operated by a relatively small number of private companies. It consists of a mixture of landfill, incineration, recycling, and composting, and is regulated under RCRA, the Clean Air Act and other related federal and state laws.

Support for linguistic macrofamilies from weighted sequence alignment

PubMed Central

Jäger, Gerhard

2015-01-01

Computational phylogenetics is in the process of revolutionizing historical linguistics. Recent applications have shed new light on controversial issues, such as the location and time depth of language families and the dynamics of their spread. So far, these approaches have been limited to single-language families because they rely on a large body of expert cognacy judgments or grammatical classifications, which is currently unavailable for most language families. The present study pursues a different approach. Starting from raw phonetic transcription of core vocabulary items from very diverse languages, it applies weighted string alignment to track both phonetic and lexical change. Applied to a collection of ∼1,000 Eurasian languages and dialects, this method, combined with phylogenetic inference, leads to a classification in excellent agreement with established findings of historical linguistics. Furthermore, it provides strong statistical support for several putative macrofamilies contested in current historical linguistics. In particular, there is a solid signal for the Nostratic/Eurasiatic macrofamily. PMID:26403857

Cliophysics: Socio-Political Reliability Theory, Polity Duration and African Political (In)stabilities

PubMed Central

Cherif, Alhaji; Barley, Kamal

2010-01-01

Quantification of historical sociological processes have recently gained attention among theoreticians in the effort of providing a solid theoretical understanding of the behaviors and regularities present in socio-political dynamics. Here we present a reliability theory of polity processes with emphases on individual political dynamics of African countries. We found that the structural properties of polity failure rates successfully capture the risk of political vulnerability and instabilities in which , , , and of the countries with monotonically increasing, unimodal, U-shaped and monotonically decreasing polity failure rates, respectively, have high level of state fragility indices. The quasi-U-shape relationship between average polity duration and regime types corroborates historical precedents and explains the stability of the autocracies and democracies. PMID:21206911

Indoor radon activity concentration measurements in the great historical museums of University of Naples, Italy.

PubMed

Quarto, Maria; Pugliese, Mariagabriella; Loffredo, Filomena; La Verde, Giuseppe; Roca, Vincenzo

2016-01-01

Indoor radon activity concentrations were measured in seven Museums of University of Naples, very old buildings of great historical value. The measurements were performed using a time-integrated technique based on LR-115 solid-state nuclear track detectors. The annual average concentrations were found to range from 40 up to 1935 Bq m(-3) and in 26 % of measurement sites, the values were higher than 500 Bq m(-3) which is the limit value of Italian legislation for workplace. Moreover, we analysed the seasonal variations of radon concentrations observing the highest average in cold weather than in warm. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Cholera in Thomas Mann's Death in Venice.

PubMed

Rütten, Thomas

2009-01-01

The article sets the cholera motif in Thomas Mann's famous novella Death in Venice against the historical context from which it partially originates. It is shown that this motif, while undoubtedly appropriated to serve Mann's own poetic ends, has a solid grounding in historical and autobiographical fact, thus blurring the boundaries between fact and fiction. The article illustrates the verifiable events of the outbreak of the Venetian cholera epidemic in May 1911, which Mann partly witnessed himself, during a holiday trip to Brioni and Venice, and partly heard and read about. It is established that Thomas Mann's account of the cholera in Venice in his novella is characterised by a rare and almost preternatural insightfulness into an otherwise murky affair that was marked by rumours, speculations and denials.

Combustion characteristics and turbulence modeling of swirling reacting flow in solid fuel ramjet

NASA Astrophysics Data System (ADS)

Musa, Omer; Xiong, Chen; Changsheng, Zhou

2017-10-01

This paper reviews the historical studies have been done on the solid-fuel ramjet engine and difficulties associated with numerical modeling of swirling flow with combustible gases. A literature survey about works related to numerical and experimental investigations on solid-fuel ramjet as well as using swirling flow and different numerical approaches has been provided. An overview of turbulence modeling of swirling flow and the behavior of turbulence at streamline curvature and system rotation are presented. A new and simple curvature/correction factor is proposed in order to reduce the programming complexity of SST-CC turbulence model. Finally, numerical and experimental investigations on the impact of swirling flow on SFRJ have been carried out. For that regard, a multi-physics coupling code is developed to solve the problems of multi-physics coupling of fluid mechanics, solid pyrolysis, heat transfer, thermodynamics, and chemical kinetics. The connected-pipe test facility is used to carry out the experiments. The results showed a positive impact of swirling flow on SFRJ along with, three correlations are proposed.

Characteristics and trends of streamflow and dissolved solids in the upper Colorado River Basin, Arizona, Colorado, New Mexico, Utah, and Wyoming

USGS Publications Warehouse

Liebermann, Timothy D.; Mueller, David K.; Kircher, James E.; Choquette, Anne F.

1989-01-01

Annual and monthly concentrations and loads of dissolved solids and major constituents were estimated for 70 streamflow-gaging stations in the Upper Colorado River Basin. Trends in streamflow, dissolved-solids concentrations, and dissolved-solids loads were identified. Nonparametric trend-analysis techniques were used to determine step trends resulting from human activities upstream and long-term monotonic trends. Results were compared with physical characteristics of the basin and historical water-resource development in the basin to determine source areas of dissolved solids and possible cause of trends. Mean annual dissolved-solids concentration increases from less than 100 milligrams per liter in the headwater streams to more than 500 milligrams per liter in the outflow from the Upper Colorado River Basin. All the major tributaries that have high concentrations of dissolved solids are downstream from extensive areas of irrigated agriculture. However, irrigation predated the period of record for most sites and was not a factor in many identified trends. Significant annual trends were identified for 30 sites. Most of these trends were related to transbasin exports, changes in land use, salinity-control practices, or reservoir development. The primary factor affecting streamflow and dissolved-solids concentration and load has been the construction of large reservoirs. Reservoirs have decreased the seasonal and annual variability of streamflow and dissolved solids in streams that drain the Gunnison and San Juan River basins. Fontenelle and Flaming Gorge Reservoirs have increased the dissolved-solids load in the Green River because of dissolution of mineral salts from the bank material. The largest trends occurred downstream from Lake Powell. However, the period of record since the completion of filling was too short to estimate the long-term effects of that reservoir.

European Scientific Notes. Volume 36, Number 9

DTIC Science & Technology

1982-09-30

studies of super- One of the chief reasons the’ foregoing "conducting tunneling, ultrasonic attenuation , activity was initiated was the historical...paper entitled "The Effect of HTPB propellant and binder. Results from tests Polymer Characteristics on Propellant using 105-mm munitions show that...polybutadiene ( HTPB ) composite solid Dr. A. Iwama (Institute of Space and propellants. The influence of the polymer Astronautical Science, Tokyo, Japan

Understanding Violence Through Social Media

DTIC Science & Technology

2017-12-01

understudied. To determine the feasibility of social media utilization in conflict prediction, we compared historical conflict data and social media...research, we conclude that social media metadata has a positive impact on conflict prediction when compared with historical conflict data. Additionally...of social media utilization in conflict prediction, we compared historical conflict data and social media metadata, utilizing over 829,537 geo

Historical and recent flora of the Santa Rita Experimental Range

Treesearch

Alvin L. Medina

2003-01-01

The historical flora of the Santa Rita Experimental Range was composed from historical lists of plants collected by various investigators since 1903. Plant accessions were verified from lists of plant specimens housed at the Rocky Mountain Research Station herbarium in Flagstaff, AZ, and the Rocky Mountain National Herbarium in Laramie, WY. Recent additions (1980 to...

Textbook vs. Historical Fiction: Impact on Social Studies Students

ERIC Educational Resources Information Center

Rider, Amanda

2013-01-01

The purpose of this study was to examine the effects of adding historical fiction novels as a supplement to the textbook in an eighth grade social studies course. This qualitative study focused on student interest and feedback as their social studies class was altered through the addition of historical fiction novels. The research questions were…

Radiation exposure due to local fallout from Soviet atmospheric nuclear weapons testing in Kazakhstan: solid cancer mortality in the Semipalatinsk historical cohort, 1960-1999.

PubMed

Bauer, Susanne; Gusev, Boris I; Pivina, Ludmila M; Apsalikov, Kazbek N; Grosche, Bernd

2005-10-01

Little information is available on the health effects of exposures to fallout from Soviet nuclear weapons testing and on the combined external and internal environmental exposures that have resulted from these tests. This paper reports the first analysis of the Semipalatinsk historical cohort exposed in the vicinity of the Semipalatinsk nuclear test site, Kazakhstan. The cohort study, which includes 19,545 inhabitants of exposed and comparison villages of the Semipalatinsk region, was set up in the 1960s and comprises 582,750 person-years of follow-up between 1960 and 1999. Cumulative effective radiation dose estimates in this cohort range from 20 mSv to approximately 4 Sv. Rates of mortality and cancer mortality in the exposed group substantially exceeded those of the comparison group. Dose-response analyses within the exposed group confirmed a significant trend with dose for all solid cancers (P < 0.0001) and for digestive and respiratory cancers (P = 0.0255 and P < 0.0001), whereas no consistent dose-response trend was found for all causes of death (P = 0.4296). Regarding specific cancer sites, a significant trend with dose was observed for lung cancer (P = 0.0001), stomach cancer (P = 0.0050), and female breast cancer (P = 0.0040) as well as for esophagus cancer in women (P = 0.0030). The excess relative risk per sievert for all solid cancers combined was 1.77 (1.35; 2.27) based on the total cohort data, yet a selection bias regarding the comparison group could not be entirely ruled out. The excess relative risk per sievert based on the cohort's exposed group was 0.81 (0.46; 1.33) for all solid cancers combined and thus still exceeds current risk estimates from the Life Span Study. Future epidemiological assessments based on this cohort will benefit from extension of follow-up and ongoing validation of dosimetric data.

46 CFR 97.12-1 - Definition of a bulk solid cargo.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Definition of a bulk solid cargo. 97.12-1 Section 97.12... OPERATIONS Bulk Solid Cargoes § 97.12-1 Definition of a bulk solid cargo. (a) A bulk solid cargo— (1.... (b) Additional requirements for bulk solid materials needing special handling are contained in Part...

4. Historic American Buildings Survey, Glenn C. Wilson, Photographer March ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Historic American Buildings Survey, Glenn C. Wilson, Photographer March 1, 1934 VIEW OF SOUTHWEST CORNER, SHOWING RECENT ADDITION. - Friederich Homann Saddlery & Residence, 136 Seguin Street, New Braunfels, Comal County, TX

5. Historic American Buildings Survey, Louis C. Page, Jr., Photographer ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Historic American Buildings Survey, Louis C. Page, Jr., Photographer April 4, 1934 RECENT ADDITION FROM EAST. - French Legation to Republic of Texas, Seventh & San Marcos Streets, Austin, Travis County, TX

Effect of organometallic fuel additives on nanoparticle emissions from a gasoline passenger car.

PubMed

Gidney, Jeremy T; Twigg, Martyn V; Kittelson, David B

2010-04-01

Particle size measurements were performed on the exhaust of a car operating on a chassis dynamometer fueled with standard gasoline and gasoline containing low levels of Pb, Fe, and Mn organometallic additives. When additives were present there was a distinct nucleation mode consisting primarily of sub-10 nm nanoparticles. At equal molar dosing Mn and Fe gave similar nanoparticle concentrations at the tailpipe, whereas Pb gave a considerably lower concentration. A catalytic stripper was used to remove the organic component of these particles and revealed that they were mainly solid and, because of their association with inorganic additives, presumably inorganic. Solid nucleation mode nanoparticles of similar size and concentration to those observed here from a gasoline engine with Mn and Fe additives have also been observed from modern heavy-duty diesel engines without aftertreatment at idle, but these solid particles are a small fraction of the primarily volatile nucleation mode particles emitted. The solid nucleation mode particles emitted by the diesel engines are likely derived from metal compounds in the lubrication oil, although carbonaceous particles cannot be ruled out. Significantly, most of these solid nanoparticles emitted by both engine types fall below the 23 nm cutoff of the PMP number regulation.

EVALUATION OF FABRIC MEMBRANES FOR USE IN SALTSTONE DRAIN WATER SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickenheim, B.; Miller, D.; Burket, P.

2012-03-08

Saltstone Disposal Unit 2 contains a sheet drain fabric intended to separate solids from drain water to be returned to the Salt Feed Tank. A similar system installed in Vault 4 appears to be ineffective in keeping solids out of the drain water return lines. Waste Solidification Engineering is considering installation of an additional fabric membrane to supplement the existing sheet drain in SDU 2. Amerdrain 200 is the product currently installed in SDU 2. This product is no longer available, so Sitedrain 94 was used as the replacement product in this testing. Fabrics with apparent opening sizes of 10,more » 25, 50 and 100 microns were evaluated. These fabrics were evaluated under three separate test conditions, a water flow test, a solids retention test and a grout pour test. A flow test with water showed that installation of an additional filter layer will predictably reduce the theoretical flux through the sheet drain. The manufacturer reports the flux for Sitedrain 94 as 150 gpm/ft{sup 2} by ASTM D-4491. This compares reasonably well with the 117 gpm/ft{sup 2} obtained in this testing. A combination of the 10 micron fabric with Sitedrain 94 could be expected to decrease flux by about 10 times as compared to Sitedrain 94 alone. The different media were used to filter a slag and fly ash mixture from water. Slag historically has the smallest nominal particle size of the premix components. Cement was omitted from the test because of its reactivity with water would prohibit accurately particle size measurements of the filtered samples. All four media sizes were able to remove greater than 95% of particles larger than 100 microns from the slurry. The smaller opening sizes were increasingly effective in removing more particles. The 10 micron filter captured 15% of the total amount of solids used in the test. This result implies that some insoluble particles may still be able to enter the drain water collection system, although the overall solids rejection is significantly improved over the current design. Test boxes were filled with grout to evaluate the performance of the sheet drain and fabrics in a simulated vault environment. All of the tests produced a similar amount of drain water, between 8-11% of the amount of water in the mix, which is expected with the targeted formulation. All of the collected drain waters contained some amount of solids, although the 10 micron filter did not appear to allow any premix materials to pass through. The solids collected from this box are believed to consist of calcium carbonate based on one ICP-AES measurement. Any of the four candidate fabrics would be an improvement over the sheet drain alone relative to solids removal. The 10 micron fabric is the only candidate that stopped all premix material from passing. The 10 micron fabric will also cause the largest decrease in flux. This decrease in flux was not enough to inhibit the total amount of drain water removed, but may lead to increased time to remove standing water prior to subsequent pours in the facility. The acceptability of reduced liquid flux through the 10 micron fabric will depend on the amount of excess water to be removed, the time available for water removal and the total area of fabric installed at the disposal cell.« less

Historical Research Skills Development in Light of a Training Program for Secondary Stage History Teachers

ERIC Educational Resources Information Center

Al-qout, Ghada Ahmed

2017-01-01

The study aimed to design a training program to develop the historical research skills after defining the nature of the historical research skills that the history teachers are required to master, especially the secondary stage teachers, in addition to defining the opinions of the educational supervisors on the extent to which the secondary…

2. Historic American Buildings Survey E. W. Russell, Photographer, January ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Historic American Buildings Survey E. W. Russell, Photographer, January 8, 1937 REAR VIEW SHOWING RECENT ADDITION - Nelias Fall House, County Road 96 (Old Saint Stephens Road), Mount Vernon, Mobile County, AL

Testing of Environmentally Preferable Aluminum Pretreatments and Coating Systems for Use on Space Shuttle Solid Rocket Boosters (SRB)

NASA Technical Reports Server (NTRS)

Clayton, C.; Raley, R.; Zook, L.

2001-01-01

The solid rocket booster (SRB) has historically used a chromate conversion coating prior to protective finish application. After conversion coating, an organic paint system consisting of a chromated epoxy primer and polyurethane topcoat is applied. An overall systems approach was selected to reduce waste generation from the coatings application and removal processes. While the most obvious waste reduction opportunity involved elimination of the chromate conversion coating, several other coating system configurations were explored in an attempt to reduce the total waste. This paper will briefly discuss the use of a systems view to reduce waste generation from the coating process and present the results of the qualification testing of nonchromated aluminum pretreatments and alternate coating systems configurations.

2018 DOE Solid-State Lighting Project Portfolio

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The 2018 Solid-State Lighting Project Portfolio provides an overview of all SSL projects that have been funded by DOE since 2000. Projects that were active during 2017 are found in the main body of this report, and all historic projects can be found in the appendix. Within these sections, project profiles are sorted by technology type (i.e., LED or OLED) and then by performer name. A profile is provided on each project. Each profile includes a brief technical description, as well as information about project partners, funding, and the research period. This report is updated annually, although the research describedmore » in the Portfolio changes periodically as new projects are initiated and existing ones are concluded.« less

Materials for Adaptive Structural Acoustic Control. Volume 3

DTIC Science & Technology

1994-04-11

criteria have been met for a partcular application, it then becomes advantageous to reduce costs by miniaturizing and/or reducing the power delivered...MAELSG FRintended to develop motion or vibration. such as high power COUPLING sonar, while a high g constant is desirable for sensor Histor of...which is another stable chips, which must be adjusted using solid- power and miniaturization. crystal slate in which the relative positions stale

75 FR 3782 - Notice of Final Federal Agency Actions on Interstate 84 Highway in Idaho

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-22

... Wildlife Coordination Act [16 U.S.C. 661- 667(d)]; Migratory Bird Treaty Act [16 U.S.C. 703-712]. 4...)]; Archeological and Historic Preservation Act [16 U.S.C. 469-469(c)]. 5. Land: Section 4(f) of The Department of... Protection Policy Act (FPPA) [7 U.S.C. 4201-4209]; Solid Waste Disposal Act, as amended by the Resource...

Sample results from the integrated salt disposition program macrobatch 6 tank 21H qualifications MST solids sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

2013-02-26

Savannah River National Laboratory (SRNL) performed experiments on qualification material for use in the Integrated Salt Disposition Program (ISDP) Batch 6 processing. As part of this qualification work, SRNL performed an Actinide Removal Process (ARP) test. From this test, the residual monosodium titanate (MST) was analyzed for radionuclide uptake. The results of these analyses are reported and are within historical precedent.

Ground-Based Aerosol Measurements | Science Inventory ...

EPA Pesticide Factsheets

Atmospheric particulate matter (PM) is a complex chemical mixture of liquid and solid particles suspended in air (Seinfeld and Pandis 2016). Measurements of this complex mixture form the basis of our knowledge regarding particle formation, source-receptor relationships, data to test and verify complex air quality models, and how PM impacts human health, visibility, global warming, and ecological systems (EPA 2009). Historically, PM samples have been collected on filters or other substrates with subsequent chemical analysis in the laboratory and this is still the major approach for routine networks (Chow 2005; Solomon et al. 2014) as well as in research studies. In this approach, air, at a specified flow rate and time period, is typically drawn through an inlet, usually a size selective inlet, and then drawn through filters, 1 INTRODUCTION Atmospheric particulate matter (PM) is a complex chemical mixture of liquid and solid particles suspended in air (Seinfeld and Pandis 2016). Measurements of this complex mixture form the basis of our knowledge regarding particle formation, source-receptor relationships, data to test and verify complex air quality models, and how PM impacts human health, visibility, global warming, and ecological systems (EPA 2009). Historically, PM samples have been collected on filters or other substrates with subsequent chemical analysis in the laboratory and this is still the major approach for routine networks (Chow 2005; Solomo

Erosion and physical transport via overland flow of arsenic and lead bound to silt-sized particles

PubMed Central

Cadwalader, G. Owen; Renshaw, Carl E.; Jackson, Brian P.; Magilligan, Francis J.; Landis, Joshua D.; Bostick, Benjamin C.

2011-01-01

Understanding of the transport mechanisms of contaminated soils and sediment is essential for the sustainable management of contaminated lands. In New England and elsewhere, vast areas of agricultural lands are contaminated by the historical application of lead-arsenate pesticides. Left undisturbed the physical and chemical mobility of As and Pb in these soils is limited due to their strong affinity for adsorption onto solid phases. However, soil disturbance promotes erosion and overland flow during intense rainstorms. Here we investigate the event-scale transport of disturbed As and Pb contaminated soils through measurement of concentrations of As and Pb in suspended sediment and changes in Pb isotopic ratios in overland flow. Investigation of several rain events shows that where land disturbance has occurred, physical transport of silt-sized particles and aggregates is the primary transport vector of As and Pb derived from pesticide-contaminated soil. Although both As and Pb are associated with similarly-sized particles, we find that solid-phase As is more effectively mobilized and transported than Pb. Our results demonstrate that anthropogenic land disturbance of historical lands contaminated with lead-arsenate pesticides may redistribute, through physical transport, significant amounts of As, and lesser amounts of Pb, to riparian and stream sediments, where they are potentially more bioavailable. PMID:21552357

Subsidence Serves as an Indicator of Groundwater Arsenic Risk in the San Joaquin Valley, California

NASA Astrophysics Data System (ADS)

Smith, R.; Knight, R. J.; Fendorf, S. E.

2016-12-01

Groundwater arsenic concentrations dominantly result from anaerobic conditions. Within aquifers, clays are typically the major hosts of solid-phase arsenic, and clay layers often have restricted oxygen supply, resulting in anaerobic conditions and the concomitant relase of arsenic to groundwater. But it is not until water is drawn from the clay layers, through over-pumping of aquifers, that arsenic enters the water supply. Due to the mechanical properties of clays, the volume of groundwater withdrawn is effectively approximated by their vertical deformation, the sum of which is expressed at the surface as subsidence. As a result, subsidence can serve as an indicator, or "early warning system", of the presence of arsenic in the pumped groundwater. In the San Joaquin Valley of California, there has been significant subsidence due to groundwater extraction from clays for nearly a century. Historical subsidence in this area has been measured with leveling surveys, GPS and extensometers, and has been reproduced in groundwater models. More recent subsidence can be measured directly using Interferometric Synthetic Aperture Radar (InSAR). We use recent (post-2007) arsenic level data from the southern portion of the San Joaquin Valley to train a random forest model. Predictors in the model include historical (pre-2002) estimates of subsidence, more recent (2007-2011) InSAR estimates of subsidence, and other predictors representing additional mechanisms that could affect arsenic levels in groundwater, such as groundwater flow, redox potential and position in the basin. We find that recent subsidence is a strong predictor of arsenic levels; historical subsidence could have some impact but is less significant. These results indicate that avoiding over-pumping of the aquifer may improve water quality over a time period on the order of 10 years. Incorporating subsidence into arsenic prediction maps can improve our ability to identify and manage areas that have a higher risk of arsenic contamination due to removal of groundwater from clays.

Mission Success of U.S. Launch Vehicle Flights from a Propulsion Stage-Based Perspective: 1980-2015

NASA Technical Reports Server (NTRS)

Go, Susie; Lawrence, Scott L.; Mathias, Donovan L.; Powell, Ryann

2017-01-01

This report documents a study of the historical safety and reliability trends of U.S. space launch vehicles from 1980 to 2015. The launch data history is examined to determine whether propulsion technology choices drove launch system risk and is used to understand how different propulsion system failures manifested into different failure scenarios. The historical data is processed by launch vehicle stage, where a stage is limited by definition to a single propulsion technology, either liquid or solid. Results are aggregated in terms of failure trends and manifestations as a functions of different propulsion stages. Failure manifestations are analyzed in order to understand the types and frequencies of accident environments in which an abort system for a crewed vehicle would be required to operate.

Microstructural characterization of random packings of cubic particles

PubMed Central

Malmir, Hessam; Sahimi, Muhammad; Tabar, M. Reza Rahimi

2016-01-01

Understanding the properties of random packings of solid objects is of critical importance to a wide variety of fundamental scientific and practical problems. The great majority of the previous works focused, however, on packings of spherical and sphere-like particles. We report the first detailed simulation and characterization of packings of non-overlapping cubic particles. Such packings arise in a variety of problems, ranging from biological materials, to colloids and fabrication of porous scaffolds using salt powders. In addition, packing of cubic salt crystals arise in various problems involving preservation of pavements, paintings, and historical monuments, mineral-fluid interactions, CO2 sequestration in rock, and intrusion of groundwater aquifers by saline water. Not much is known, however, about the structure and statistical descriptors of such packings. We have developed a version of the random sequential addition algorithm to generate such packings, and have computed a variety of microstructural descriptors, including the radial distribution function, two-point probability function, orientational correlation function, specific surface, and mean chord length, and have studied the effect of finite system size and porosity on such characteristics. The results indicate the existence of both spatial and orientational long-range order in the packing, which is more distinctive for higher packing densities. The maximum packing fraction is about 0.57. PMID:27725736

Microstructural characterization of random packings of cubic particles

DOE PAGES

Malmir, Hessam; Sahimi, Muhammad; Tabar, M. Reza Rahimi

2016-10-11

Understanding the properties of random packings of solid objects is of critical importance to a wide variety of fundamental scientific and practical problems. The great majority of the previous works focused, however, on packings of spherical and sphere-like particles. We report the first detailed simulation and characterization of packings of non-overlapping cubic particles. Such packings arise in a variety of problems, ranging from biological materials, to colloids and fabrication of porous scaffolds using salt powders. In addition, packing of cubic salt crystals arise in various problems involving preservation of pavements, paintings, and historical monuments, mineral-fluid interactions, CO 2 sequestration inmore » rock, and intrusion of groundwater aquifers by saline water. Not much is known, however, about the structure and statistical descriptors of such packings. We have developed a version of the random sequential addition algorithm to generate such packings, and have computed a variety of microstructural descriptors, including the radial distribution function, two-point probability function, orientational correlation function, specific surface, and mean chord length, and have studied the effect of finite system size and porosity on such characteristics. Here, the results indicate the existence of both spatial and orientational long-range order in the packing, which is more distinctive for higher packing densities.« less

THz Spectroscopy and Spectroscopic Database for Astrophysics

NASA Technical Reports Server (NTRS)

Pearson, John C.; Drouin, Brian J.

2006-01-01

Molecule specific astronomical observations rely on precisely determined laboratory molecular data for interpretation. The Herschel Heterodyne Instrument for Far Infrared, a suite of SOFIA instruments, and ALMA are each well placed to expose the limitations of available molecular physics data and spectral line catalogs. Herschel and SOFIA will observe in high spectral resolution over the entire far infrared range. Accurate data to previously unimagined frequencies including infrared ro-vibrational and ro-torsional bands will be required for interpretation of the observations. Planned ALMA observations with a very small beam will reveal weaker emission features requiring accurate knowledge of higher quantum numbers and additional vibrational states. Historically, laboratory spectroscopy has been at the front of submillimeter technology development, but now astronomical receivers have an enormous capability advantage. Additionally, rotational spectroscopy is a relatively mature field attracting little interest from students and funding agencies. Molecular database maintenance is tedious and difficult to justify as research. This severely limits funding opportunities even though data bases require the same level of expertise as research. We report the application of some relatively new receiver technology into a simple solid state THz spectrometer that has the performance required to collect the laboratory data required by astronomical observations. Further detail on the lack of preparation for upcoming missions by the JPL spectral line catalog is given.

Innovation leading the way: application of lean manufacturing to sample management.

PubMed

Allen, M; Wigglesworth, M J

2009-06-01

Historically, sample management successfully focused on providing compound quality and tracking distribution within a diverse geographic. However, if a competitive advantage is to be delivered in a changing environment of outsourcing, efficiency and customer service must now improve or face reconstruction. The authors have used discrete event simulation to model the compound process from chemistry to assay and applied lean manufacturing techniques to analyze and improve these processes. In doing so, they identified a value-adding process time of just 11 min within a procedure that took days. Modeling also allowed the analysis of equipment and human resources necessary to complete the expected demand in an acceptable cycle time. Layout and location of sample management and screening departments are key in allowing process integration, creating rapid flow of work, and delivering these efficiencies. Following this analysis and minor process changes, the authors have demonstrated for 2 programs that solid compounds can be converted to assay-ready plates in less than 4 h. In addition, it is now possible to deliver assay data from these compounds within the same working day, allowing chemistry teams more flexibility and more time to execute the next chemistry round. Additional application of lean manufacturing principles has the potential to further decrease cycle times while using fewer resources.

THz Spectroscopy and Spectroscopic Database for Astrophysics

NASA Technical Reports Server (NTRS)

Pearson, John C.; Drouin, Brian J.

2006-01-01

Molecule specific astronomical observations rely on precisely determined laboratory molecular data for interpretation. The Herschel Heterodyne Instrument for Far Infrared, a suite of SOFIA instruments, and ALMA are each well placed to expose the limitations of available molecular physics data and spectral line catalogs. Herschel and SOFIA will observe in high spectral resolution over the entire far infrared range. Accurate data to previously unimagined frequencies including infrared ro-vibrational and ro-torsional bands will be required for interpretation of the observations. Planned ALMA observations with a very small beam will reveal weaker emission features requiring accurate knowledge of higher quantum numbers and additional vibrational states. Historically, laboratory spectroscopy has been at the front of submillimeter technology development, but now astronomical receivers have an enormous capability advantage. Additionally, rotational spectroscopy is a relatively mature field attracting little interest from students and funding agencies. Molecular data base maintenance is tedious and difficult to justify as research. This severely limits funding opportunities even though data bases require the same level of expertise as research. We report the application of some relatively new receiver technology into a simple solid state THz spectrometer that has the performance required to collect the laboratory data required by astronomical observations. Further detail on the lack of preparation for upcoming missions by the JPL spectral line catalog is given.

Modal Survey of ETM-3, A 5-Segment Derivative of the Space Shuttle Solid Rocket Booster

NASA Technical Reports Server (NTRS)

Nielsen, D.; Townsend, J.; Kappus, K.; Driskill, T.; Torres, I.; Parks, R.

2005-01-01

The complex interactions between internal motor generated pressure oscillations and motor structural vibration modes associated with the static test configuration of a Reusable Solid Rocket Motor have potential to generate significant dynamic thrust loads in the 5-segment configuration (Engineering Test Motor 3). Finite element model load predictions for worst-case conditions were generated based on extrapolation of a previously correlated 4-segment motor model. A modal survey was performed on the largest rocket motor to date, Engineering Test Motor #3 (ETM-3), to provide data for finite element model correlation and validation of model generated design loads. The modal survey preparation included pretest analyses to determine an efficient analysis set selection using the Effective Independence Method and test simulations to assure critical test stand component loads did not exceed design limits. Historical Reusable Solid Rocket Motor modal testing, ETM-3 test analysis model development and pre-test loads analyses, as well as test execution, and a comparison of results to pre-test predictions are discussed.

Modified computation of the nozzle damping coefficient in solid rocket motors

NASA Astrophysics Data System (ADS)

Liu, Peijin; Wang, Muxin; Yang, Wenjing; Gupta, Vikrant; Guan, Yu; Li, Larry K. B.

2018-02-01

In solid rocket motors, the bulk advection of acoustic energy out of the nozzle constitutes a significant source of damping and can thus influence the thermoacoustic stability of the system. In this paper, we propose and test a modified version of a historically accepted method of calculating the nozzle damping coefficient. Building on previous work, we separate the nozzle from the combustor, but compute the acoustic admittance at the nozzle entry using the linearized Euler equations (LEEs) rather than with short nozzle theory. We compute the combustor's acoustic modes also with the LEEs, taking the nozzle admittance as the boundary condition at the combustor exit while accounting for the mean flow field in the combustor using an analytical solution to Taylor-Culick flow. We then compute the nozzle damping coefficient via a balance of the unsteady energy flux through the nozzle. Compared with established methods, the proposed method offers competitive accuracy at reduced computational costs, helping to improve predictions of thermoacoustic instability in solid rocket motors.

Influence of porewater sulfide on methylmercury production and partitioning in sulfate-impacted lake sediments.

PubMed

Bailey, Logan T; Mitchell, Carl P J; Engstrom, Daniel R; Berndt, Michael E; Coleman Wasik, Jill K; Johnson, Nathan W

2017-02-15

In low-sulfate and sulfate-limited freshwater sediments, sulfate loading increases the production of methylmercury (MeHg), a potent and bioaccumulative neurotoxin. Sulfate loading to anoxic sediments leads to sulfide production that can inhibit mercury methylation, but this has not been commonly observed in freshwater lakes and wetlands. In this study, sediments were collected from sulfate-impacted, neutral pH, surface water bodies located downstream from ongoing and historic mining activities to examine how chronic sulfate loading produces porewater sulfide, and influences MeHg production and transport. Sediments were collected over two years, during several seasons from lakes with a wide range of overlying water sulfate concentration. Samples were characterized for in-situ solid phase and porewater MeHg, Hg methylation potentials via incubations with enriched stable Hg isotopes, and sulfur, carbon, and iron content and speciation. Porewater sulfide reflected historic sulfur loading and was strongly related to the extractable iron content of sediment. Overall, methylation potentials were consistent with the accumulation of MeHg on the solid phase, but both methylation potentials and MeHg were significantly lower at chronically sulfate-impacted sites with a low solid-phase Fe:S ratio. At these heavily sulfate-impacted sites that also contained elevated porewater sulfide, both MeHg production and partitioning are influenced: Hg methylation potentials and sediment MeHg concentrations are lower, but occasionally porewater MeHg concentrations in sediment are elevated, particularly in the spring. The dual role of sulfide as a ligand for inorganic mercury (decreasing bioavailability) and methylmercury (increasing partitioning into porewater) means that elucidating the role of iron and sulfur loads as they define porewater sulfide is key to understanding sulfate's influence on MeHg production and partitioning in sulfate-impacted freshwater sediment. Copyright © 2016 Elsevier B.V. All rights reserved.

Differential reinforcement of enzymatic hydrolysis by adding chemicals and accessory proteins to high solid loading substrates with different pretreatments.

PubMed

Du, Jian; Song, Wenxia; Zhang, Xiu; Zhao, Jian; Liu, Guodong; Qu, Yinbo

2018-04-23

High dosage of enzyme is required to achieve effective lignocellulose hydrolysis, especially at high-solid loadings, which is a significant barrier to large-scale bioconversion of lignocellulose. Here, we screened four chemical additives and three accessory proteins for their effects on the enzymatic hydrolysis of various lignocellulosic materials. The effects were found to be highly dependent on the composition and solid loadings of substrates. For xylan-extracted lignin-rich corncob residue, the enhancing effect of PEG 6000 was most pronounced and negligibly affected by solid content, which reduced more than half of enzyme demand at 20% dry matter (DM). Lytic polysaccharide monooxygenase enhanced the hydrolysis of ammonium sulfite wheat straw pulp, and its addition reduced about half of protein demand at the solid loading of 20% DM. Supplementation of the additives in the hydrolysis of pure cellulose and complex lignocellulosic materials revealed that their effects are tightly linked to pretreatment strategies.

A Good Name and Great Riches: Rebranding Solid State Physics for the National Laboratories

NASA Astrophysics Data System (ADS)

Martin, Joseph

2012-03-01

In 1943 Oliver Buckley, lamenting the inadequacy of term ``physics'' to evoke what physicists did, quoted the proverb, ``A good name is rather to be chosen than great riches.'' Some forty years later, solid state physicists confronted similar discontent with their name, precipitating the rise of the appellation ``condensed matter physics.'' Ostensibly a rebranding of a well-established field, the change signaled deeper conceptual and institutional realignment. Whereas ``solid state'' emerged in the 1940s in the service of institutional aims, ``condensed matter'' more accurately captured a distinct set of theoretical and experimental approaches. Reimagining the field around core conceptual approaches set condensed matter apart from the inchoate field of materials science, which subsumed a growing proportion of solid state funding and personnel through the 1980s. Federally funded research installations were the source of ``great riches'' for scientific research. The DOE National Laboratory System and the DARPA network of Interdisciplinary Laboratories, given their responsiveness to shifts in national funding priorities, provide a sensitive historical instrument through which to trace the transition from solid state to condensed matter. The reorganization of solid state in response to the evolution of national priorities and funding practices precipitated a sharpening of the field's intellectual mission. At the same time, it reflected the difficulties solid state faced articulating its intellectual--as opposed to technological--merit. The proverb continues, `` and loving favor rather than silver and gold.'' The adoption of a name that emphasized intellectual cohesion and associated social esteem exposed the growing tension between technology-oriented national funding goals for materials research and condensed matter physics' ascendant intellectual identity.

1. Historic American Buildings Survey (Fed.) Stanley P. Mixon, Photographer ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Historic American Buildings Survey (Fed.) Stanley P. Mixon, Photographer Sept. 6, 1940 (A) HOUSE AT GREEN AND DEFOREST STREET, ENTRANCE AND CIRCULAR PORCH (The latter probably a recent addition) - Green & De Forest Streets (House), Watertown, Litchfield County, CT

Environmental Impact Statement. Deactivation of the Minuteman II Missile Wing at Whiteman Air Force Base, Missouri

DTIC Science & Technology

1992-08-01

Hazardous Air Pollutants NHPA National Historic Preservation Act NIOSH National Institute for Occupational Safety and Health 1 NOEL no observed effect ...Pantex 3 document concluded that direct measurable effects to the health and safety of the general public or adverse impacts to the environment are likely...safety; and transportation accident potential. Solid wastes and underground storage tanks are also discussed in thic ection. Potential effects to health

Rheological modification of corn stover biomass at high solids concentrations

Treesearch

Joseph R. Samaniuk; C. Tim Scott; Thatcher W. Root; Daniel J. Klingenberg

2012-01-01

Additives were tested for their ability to modify the rheology of lignocellulosic biomass. Additive types included water-soluble polymers (WSPs), surfactants, and fine particles. WSPs were the most effective rheological modifiers, reducing yield stresses of concentrated biomass by 60–80% for additive concentrations of 1–2 wt. % (based on mass of dry biomass solids)....

Energy-effective Grinding of Inorganic Solids Using Organic Additives.

PubMed

Mishra, Ratan K; Weibel, Martin; Müller, Thomas; Heinz, Hendrik; Flatt, Robert J

2017-08-09

We present our research findings related to new formulations of the organic additives (grinding aids) needed for the efficient grinding of inorganic solids. Even though the size reduction phenomena of the inorganic solid particles in a ball mill is purely a physical process, the addition of grinding aids in milling media introduces a complex physicochemical process. In addition to further gain in productivity, the organic additive helps to reduce the energy needed for grinding, which in the case of cement clinker has major environmental implications worldwide. This is primarily due to the tremendous amounts of cement produced and almost 30% of the associated electrical energy is consumed for grinding. In this paper, we examine the question of how to optimize these grinding aids linking molecular insight into their working mechanisms, and also how to design chemical additives of improved performance for industrial comminution.

Assessment of occupational safety risks in Floridian solid waste systems using Bayesian analysis.

PubMed

Bastani, Mehrad; Celik, Nurcin

2015-10-01

Safety risks embedded within solid waste management systems continue to be a significant issue and are prevalent at every step in the solid waste management process. To recognise and address these occupational hazards, it is necessary to discover the potential safety concerns that cause them, as well as their direct and/or indirect impacts on the different types of solid waste workers. In this research, our goal is to statistically assess occupational safety risks to solid waste workers in the state of Florida. Here, we first review the related standard industrial codes to major solid waste management methods including recycling, incineration, landfilling, and composting. Then, a quantitative assessment of major risks is conducted based on the data collected using a Bayesian data analysis and predictive methods. The risks estimated in this study for the period of 2005-2012 are then compared with historical statistics (1993-1997) from previous assessment studies. The results have shown that the injury rates among refuse collectors in both musculoskeletal and dermal injuries have decreased from 88 and 15 to 16 and three injuries per 1000 workers, respectively. However, a contrasting trend is observed for the injury rates among recycling workers, for whom musculoskeletal and dermal injuries have increased from 13 and four injuries to 14 and six injuries per 1000 workers, respectively. Lastly, a linear regression model has been proposed to identify major elements of the high number of musculoskeletal and dermal injuries. © The Author(s) 2015.

Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

NASA Technical Reports Server (NTRS)

Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

2012-01-01

Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility with both paraffin and RDX, the mixture will be combined with the melted paraffin. With the melting point of the paraffin far below the decomposition temperature of the RDX, the solvent will be boiled off, leaving the crystallized RDX embedded in the paraffin. At low percentages of RDX additive and with crystallized RDX surrounded by paraffin, the fuel grains will remain inert, maintaining a key benefit of hybrids in the safety of the solid fuel.

Measuring symptoms as a critical component of drug development and evaluation in hematological diseases

PubMed Central

Williams, Loretta A; Yucel, Emre; Cortes, Jorge E; Cleeland, Charles S

2014-01-01

With the rapid development of new therapies for patients with hematological malignancies, there is an increasing need for patient report of symptom status during all phases of drug testing. The patient’s perspective on new treatments reflects treatment tolerability as well as symptom benefit, and may assist patients and clinicians in choosing treatments. Inclusion of patient-reported outcomes, more common in solid-tumor than hematological trials, provides early information about symptoms to guide decisions about appropriate dosing and supportive care needs. We provide a historical overview of the use of patient-reported outcomes and symptom assessment in solid-tumor and hematological drug development, and offer recommendations about methodological issues in the monitoring of symptoms in the drug development process in hematological clinical trials. PMID:24910769

Solid state microdosimetry.

PubMed

Bradley, P D; Rosenfeld, A B; Zaider, M

2001-09-01

A review of solid state microdosimetry is presented with an emphasis on silicon-based devices. The historical foundations and basics of microdosimetry are briefly provided. Various methods of experimental regional microdosimetry are discussed to facilitate a comparison with the more recent development of silicon microdosimetry. In particular, the performance characteristics of a proportional gas counter and a silicon microdosimeter are compared. Recent improvements in silicon microdosimetry address the issues of requirement specification, non-spherical shape, tissue equivalence, sensitive volume definition (charge collection complexity) and low noise requirements which have previously impeded the implementation of silicon-based microdosimetry. A prototype based on silicon-on-insulator technology is described along with some example results from clinical high LET radiotherapy facilities. A brief summary of the applications of microdosimetry is included. c2001 Elsevier Science B.V. All rights reserved.

Sceening, down selection, and implementation of environmentally compliant cleaning and insulation bonding for MNASA

NASA Astrophysics Data System (ADS)

Keen, Jill M.; Hutchens, D. E.; Smith, G. M.; Dillard, T. W.

1994-06-01

MNASA, a quarter-scale space shuttle solid rocket motor, has historically been processed using environmentally and physiologically harmful chemicals. This program draws from previous testing done in support of full-scale manufacturing and examines the synergy and interdependency between environmentally acceptable materials for Solid Rocket Motor insulation applications, bonding, corrosion inhibiting, painting, priming and cleaning; and then implements new materials and processes in sub-scale motors. Tests have been conducted to eliminate or minimize hazardous chemicals used in the manufacture of MNASA components and identify alternate materials and/or processes following NASA Operational Environment Team (NOET) priorities. This presentation describes implementation of high pressure water refurbishment cleaning, aqueous precision cleaning using both Brulin 815 GD and Jettacin and insulation case bonding using ODC compliant primers and adhesives.

1. Historic American Buildings Survey EAST AND SOUTH ELEVATIONS BEFORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Historic American Buildings Survey EAST AND SOUTH ELEVATIONS BEFORE ADDITION OF PORCH, ALTERATION OF WINDOWS From the Collection of the Title Insurance Company, SanDiego, Negative FEP - 1323 - Temple Beth Israel, 1502 Second Avenue, San Diego, San Diego County, CA

A Philosophical Review of Science and Society within Agricultural Education

ERIC Educational Resources Information Center

McKim, Aaron J.; Velez, Jonathan J.; Lambert, Misty D.; Balschweid, Mark A.

2017-01-01

We utilized philosophical and historical perspectives to analyze the interconnectedness between agricultural education, science, and society. Using historical evidence, the adaptive role of agricultural education was discussed and recommendations for future adaptability were described. Additionally, connections between agricultural education,…

77 FR 31400 - Nixon Presidential Historical Materials: Opening of Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... NATIONAL ARCHIVES AND RECORDS ADMINISTRATION Nixon Presidential Historical Materials: Opening of Materials AGENCY: National Archives and Records Administration. ACTION: Notice of Opening of Additional... by the Richard Nixon Presidential Library and Museum, a division of the National Archives and Records...

77 FR 58179 - Nixon Presidential Historical Materials: Opening of Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-19

... NATIONAL ARCHIVES AND RECORDS ADMINISTRATION Nixon Presidential Historical Materials: Opening of Materials AGENCY: National Archives and Records Administration ACTION: Notice of opening of additional... by the Richard Nixon Presidential Library and Museum, a division of the National Archives and Records...

76 FR 27092 - Nixon Presidential Historical Materials: Opening of Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

... NATIONAL ARCHIVES AND RECORDS ADMINISTRATION Nixon Presidential Historical Materials: Opening of Materials AGENCY: National Archives and Records Administration. ACTION: Notice of opening of additional... by the Richard Nixon Presidential Library and Museum, a division of the National Archives and Records...

75 FR 68384 - Nixon Presidential Historical Materials: Opening of Materials

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-05

... NATIONAL ARCHIVES AND RECORDS ADMINISTRATION Nixon Presidential Historical Materials: Opening of Materials AGENCY: National Archives and Records Administration. ACTION: Notice of Opening of Additional... by the Richard Nixon Presidential Library and Museum, a division of the National Archives and Records...

Solid State Multinuclear Magnetic Resonance Investigation of Electrolyte Decomposition Products on Lithium Ion Electrodes

NASA Technical Reports Server (NTRS)

DeSilva, J .H. S. R.; Udinwe, V.; Sideris, P. J.; Smart, M. C.; Krause, F. C.; Hwang, C.; Smith, K. A.; Greenbaum, S. G.

2012-01-01

Solid electrolyte interphase (SEI) formation in lithium ion cells prepared with advanced electrolytes is investigated by solid state multinuclear (7Li, 19F, 31P) magnetic resonance (NMR) measurements of electrode materials harvested from cycled cells subjected to an accelerated aging protocol. The electrolyte composition is varied to include the addition of fluorinated carbonates and triphenyl phosphate (TPP, a flame retardant). In addition to species associated with LiPF6 decomposition, cathode NMR spectra are characterized by the presence of compounds originating from the TPP additive. Substantial amounts of LiF are observed in the anodes as well as compounds originating from the fluorinated carbonates.

49 CFR 172.546 - FLAMMABLE SOLID placard.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false FLAMMABLE SOLID placard. 172.546 Section 172.546... SECURITY PLANS Placarding § 172.546 FLAMMABLE SOLID placard. (a) Except for size and color, the FLAMMABLE SOLID placard must be as follows: EC02MR91.051 (b) In addition to complying with § 172.519, the...

46 CFR 148.04-19 - Tankage, garbage or rough ammoniate, solid.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Tankage, garbage or rough ammoniate, solid. 148.04-19... CARRIAGE OF SOLID HAZARDOUS MATERIALS IN BULK Special Additional Requirements for Certain Material § 148.04-19 Tankage, garbage or rough ammoniate, solid. (a) The material must contain at least 7 percent...

49 CFR 172.546 - FLAMMABLE SOLID placard.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false FLAMMABLE SOLID placard. 172.546 Section 172.546... SECURITY PLANS Placarding § 172.546 FLAMMABLE SOLID placard. (a) Except for size and color, the FLAMMABLE SOLID placard must be as follows: EC02MR91.051 (b) In addition to complying with § 172.519, the...

Validation of enhanced stabilization of municipal solid waste under controlled leachate recirculation using FTIR and XRD.

PubMed

Sethi, Sapna; Kothiyal, N C; Nema, Arvind K

2012-07-01

Leachate recirculation at neutral PH accompanied with buffer/nutrients addition has been used successfully in earlier stabilization of municipal solid waste in bioreactor landfills. In the present study, efforts were made to enhance the stabilization rate of municipal solid waste (MSW) and organic solid waste (OSW) in simulated landfill bioreactors by controlling the pH of recirculated leachate towards slightly alkaline side in absence of additional buffer and nutrients addition. Enhanced stabilization in waste samples was monitored with the help of analytical tools like Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction (XRD). Predominance of bands assigned to inorganic compounds and comparatively lower intensities of bands for organic compounds in the FTIR spectra of waste samples degraded with leachate recirculation under controlled pH confirmed higher rate of biodegradation and mineralization of waste than the samples degraded without controlled leachate recirculation. XRD spectra also confirmed to a greater extent of mineralization in the waste samples degraded under leachate recirculation with controlled pH. Comparison of XRD spectra of two types of wastes pointed out higher degree of mineralization in organic solid waste as compared to municipal solid waste.

An historical collection of papers on nuclear thermal propulsion

NASA Astrophysics Data System (ADS)

The present volume of historical papers on nuclear thermal propulsion (NTP) encompasses NTP technology development regarding solid-core NTP technology, advanced concepts from the early years of NTP research, and recent activities in the field. Specific issues addressed include NERVA rocket-engine technology, the development of nuclear rocket propulsion at Los Alamos, fuel-element development, reactor testing for the Rover program, and an overview of NTP concepts and research emphasizing two decades of NASA research. Also addressed are the development of the 'nuclear light bulb' closed-cycle gas core and a demonstration of a fissioning UF6 gas in an argon vortex. The recent developments reviewed include the application of NTP to NASA's Lunar Space Transportation System, the use of NTP for the Space Exploration Initiative, and the development of nuclear rocket engines in the former Soviet Union.

Salt efflorescence due to water-rock interaction on the surface of tuff cave in the Yoshimi-Hyakuana Historic Site, central Japan

NASA Astrophysics Data System (ADS)

Oguchi, Chiaki T.; Kodama, Shogo; Mohammad, Rajib; Tharanga Udagedara, Dashan

2016-04-01

Artificial cave walls in Yoshimi Hyakuana Historic Site have been suffering from salt weathering since 1945 when the caves were made. To consider the processes of weathering and subsequent crystallization of secondary minerals, water-rock experiment using tuff from this area was performed. Rocks, surface altered materials, groundwater and rainwater were collected, and chemical and mineralogical characteristics of those samples were investigated. The XRD and SEM-EDS analyses were carried out for the solid samples and ICP-OES analysis was performed for the solution generated from the experiment, groundwater and rainwater. Gypsum is detected in original tuff, and on grey and whiter coloured altered materials. General chemical changes were observed on this rock. However, it is found that purple and black altered materials were mainly made due to microbiological processes.

Molecular implications of drug-polymer solubility in understanding the destabilization of solid dispersions by milling.

PubMed

Yang, Ziyi; Nollenberger, Kathrin; Albers, Jessica; Qi, Sheng

2014-07-07

The solubility of drugs in polymer matrixes has been recognized as one of the key factors governing the physical stability of solid dispersions. This study has explored the implications of drug solubility on the destabilization that occurs on milling, which is often used as an additional process for hot melt extruded (HME) solid dispersions. The theoretical drug solubility in the polymer was first predicted using various theoretical and experimental approaches. The destabilization effects of high-energy mechanical milling on the solid dispersions with drug loadings below and above the predicted solubility were then investigated using a range of thermal, microscopic, and spectroscopic techniques. Four model drug-polymer combinations were studied. The HME formulations with drug loading below the predicted solid solubility (undersaturated and true molecular dispersion) showed good stability against milling. In contrast, milling destabilized supersaturated HME dispersions via increasing molecular mobility and creating phase-separated, amorphous, drug-rich domains. However, these additional amorphous drug-rich domains created by milling show good stability under ambient conditions, though crystallization can be accelerated by additional heating. These results highlighted that the processing method used to prepare the solid dispersions may play a role in facilitating the stabilization of amorphous drug in supersaturated solid dispersions. The degree of supersaturation of the drug in the polymer showed significant impact on the destabilization behavior of milling on solid dispersions. An improved understanding of the destabilization behavior of solid dispersions upon milling can provide new insights into the processing related apparent solubility of drugs in polymers.

Curriculum. A History of the American Undergraduate Course of Study Since 1636.

ERIC Educational Resources Information Center

Rudolph, Frederick

In addition to describing the traditional college curriculum and comparing historical moments in curriculum change in America, this history defines other historic dimensions: prescription versus free choice, general versus specialized education, elite versus egalitarian education, mass versus individualized instruction, autocratic versus…

Mercury and methylmercury related to historical mercury mining in three tributaries to Lake Berryessa, Putah Creek Watershed, California

NASA Astrophysics Data System (ADS)

Sparks, G. C.; Horner, T.; Cornwell, K.; Izzo, V.; Alpers, C. N.

2014-12-01

This study examined the relative contribution of total mercury (THg) and mono-methylmercury (MMHg) from upstream historical mercury-mining districts to Lake Berryessa, a reservoir with impaired water quality because of mercury. The third and fourth largest historical mercury-producing mining districts in California are within Lake Berryessa's three largest tributary watersheds: Pope, (Upper) Putah, and Knoxville-Eticuera Creeks. Downstream of the reservoir, Putah Creek drains into the Yolo Bypass, a major source of THg and MMHg to the Sacramento-San Joaquin Delta. Water samples were collected from October 2012 to May 2014 during 37 non-storm and 8 storm events along Pope, (Upper) Putah, and Knoxville-Eticuera Creeks and analyzed for field parameters (temperature, pH, specific conductance, dissolved oxygen, and turbidity). Additionally, water samples collected during five of the non-storm and storm events were analyzed for unfiltered THg and MMHg and total suspended solids (TSS). Discharge was measured during sampling to calculate instantaneous loads. More than 120 streambed sediment samples were collected to determine the spatial variation of THg and organic carbon content (loss on ignition). Across the watersheds, unfiltered THg (in water) samples ranged from 2.3 to 125 ng/L and unfiltered MMHg (in water) samples from 0.12 to 1.0 ng/L. Concentrations of THg ranged from less than 0.0001 to 122 mg/kg in streambed sediment. Tributary reaches with elevated mercury concentrations ("hot spots") are near or downstream of historical mercury mines and have: (1) strong positive correlations between THg (in water) or MMHg (in water) and TSS (R2> 0.88, n=5); (2) higher instantaneous loads of suspended sediment, THg and MMHg than reaches with low THg and MMHg concentrations; and (3) elevated sediment organic carbon content. Tributary reaches with weaker correlations among THg, MMHg, and TSS in unfiltered water may reflect non-mining sources of dissolved THg and MMHg, such as geothermal springs and groundwater influx from shallow aquifers. The importance of suspended particulate matter relative to THg and MMHg transport in the most contaminated stream reaches indicates that erosion control is likely to be a critical factor in successful remediation efforts in the Upper Putah Creek watershed.

di Synthesis and Characterization of the Platinum-Substituted Keggin Anion alpha-H2SiPtW11O404-

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klonowski, P; Goloboy, JC; Uribe-Romo, FJ

2014-12-15

Acidification of an aqueous solution of K8SiW11O39 and K2Pt(OH)(6) to pH 4 followed by addition of excess tetramethylammonium (TMA) chloride yielded a solid mixture of TMA salts of H2SiPtW11O404- (1) and SiW12O404- (2). The former was separated from the latter by extraction into an aqueous solution and converted into tetra-n-butylammonium (TBA) and potassium salts TBA-1 and K-1. The a-H2SiPtW11O404- was identified as a monosubstituted Keggin anion using elemental analysis, IR spectroscopy, X-ray crystallography, electrospray ionization mass spectrometry, Pt-195 NMR spectroscopy, (183)W NMR spectroscopy, and W-183-W-183 2D INADEQUATE NMR spectroscopy. Both TBA-1 and K-1 readily cocrystallized with their unsubstituted Keggin anionmore » salts, TBA-2 and K-2, respectively, providing an explanation for the historical difficulty of isolating certain platinum-substituted heteropolyanions in pure form.« less

An antiseptic religion: discovering a hybridity on the flux of hygiene and Christianity.

PubMed

Kim, Shin K

2008-06-01

An antiseptic religion is a form of Protestant Christianity that was shaped in the context of colonization in Korea. This term was coined to explain a religious hybrid that was produced by the intermingling of American Evangelical Protestant Christianity, the concept of hygiene (germ theory) and indigenous Korean religiosity. This research deals with a historical process of making 'a medicalized religion' in Asia from a perspective of postcolonialism. Most of the early American Protestant missionaries in Korea were medical doctors who were influenced by the Germ theory of illness and considered Western medicine as an efficient tool to evangelize the country. As a result of their mission, a religious culture which emphasized washing away sins from the soul as analogous to washing away germs from the body was born. In addition, the Korean people developed a very unique form of public bathing ritual centered in the development of public baths to alleviate anxiety and to destabilize the solid strategies of the Japanese and the Americans, the two major colonial powers in Korea's history in the late 19th century.

NASA's Beachside Corrosion Test Site and Current Environmentally Friendly Corrosion Control Initiatives

NASA Technical Reports Server (NTRS)

Russell, Richard W.; Calle, Luz Marina; Johnston, Frederick; Montgomery, Eliza L.; Curran, Jerome P.; Kolody, Mark R.

2013-01-01

NASA began corrosion studies at the Kennedy Space Center (KSC) in 1966 during the Gemini/Apollo Programs with the evaluation of long-term corrosion protective coatings for carbon steel. KSC's Beachside Corrosion Test Site (BCTS), which has been documented by the American Society of Materials (ASM) as one of the most corrosive, naturally occurring, environments in the world, was established at that time. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pad were rendered even more severe by the acid ic exhaust from the solid rocket boosters. In the years that followed, numerous studies have identified materials, coatings, and maintenance procedures for launch hardware and equipment exposed to the highly corrosive environment at the launch pad. This paper presents a historical overview of over 45 years of corrosion and coating evaluation studies and a description of the BCTS's current capabilities. Additionally, current research and testing programs involving chromium free coatings, environmentally friendly corrosion preventative compounds, and alternates to nitric acid passivation will be discussed.

Environmental Assessment for the Construction of a Community Activities Center, Malmstrom Air Force Base, Montana

DTIC Science & Technology

2008-12-18

cannot be restored as a result of the action (e.g., extinction of a threatened or endangered species or the demolition of a historical building). For...of solid waste, including hazardous waste, and the transportation of hazardous waste. 1.6.4 Biological Resources The Endangered Species Act (16...USC 1531-1544) requires federal agencies to avoid jeopardizing the continued existence of endangered or threatened species and avoid destroying or

No Further Action Decision Under Cercla Study Area 61Z Building 202 Historic Motor Pool

DTIC Science & Technology

2000-01-01

appropriate response actions are implemented at Fort Devens under CERCLA. AOC 61Z is the former site of a motor pool at the corner of Carey and St. Mihiel...provided recommendations for response actions with the objective of identifying priorities for environmental restoration at Fort Devens . Areas...a final permit that included a list of Solid Waste Management Units requiring corrective action . In December 1989, Fort Devens was placed on the

Remarks upon the term stereotaxy: a linguistic and historical note.

PubMed

Grunert, Peter; Keiner, Doerthe; Oertel, Joachim

2015-01-01

The correct explanation of the term 'stereotaxy' is linguistically not self-evident because the Greek term stereon means not spatial but 'hard' or 'solid'. The aim of our study was to clarify the term stereotaxy historically and linguistically. We carried out our study by reviewing the neurosurgical and ancient Greek literature. The term stereotaxy is composed of two ancient Greek words: stereon and taxis. Stereon was used in particular as a technical term for geometrical solids in Greek mathematics. This term can be traced back to Platon and Euclid in the 4th and 3rd century BC, respectively. Only in this sense of the word does stereon in stereotaxy actually mean 'spatial' or '3-dimensional'. Taxis is derived from the verb tattein(τάττειν) with the meaning 'to position'. The terms 'stereotaxis' and 'stereotaxic apparatus' were introduced by Clarke and Horsley in 1908 to denote a method for the precise positioning of electrodes into the deep cerebellar nuclei of apes. The target in space was defined by 3 distances in relation to 3 orthogonal planes. Although this concept corresponded exactly to x-, y- and z-coordinates in a cartesian coordinate system, Clarke never used the concept of coordinates. The intuitive explanation of the term stereotaxy as spatial positioning is correct, but linguistically more complex than would be expected. © 2015 S. Karger AG, Basel.

48 CFR 252.219-7003 - Small business subcontracting plan (DoD contracts).

Code of Federal Regulations, 2011 CFR

2011-10-01

... clause— Historically black colleges and universities means institutions determined by the Secretary of... institution that was an integral part of such a college or university before November 14, 1986. Minority... clause, includes historically black colleges and universities and minority institutions, in addition to...

48 CFR 252.219-7003 - Small business subcontracting plan (DoD contracts).

Code of Federal Regulations, 2014 CFR

2014-10-01

... clause— Historically black colleges and universities means institutions determined by the Secretary of... institution that was an integral part of such a college or university before November 14, 1986. Minority... clause, includes historically black colleges and universities and minority institutions, in addition to...

48 CFR 252.219-7003 - Small business subcontracting plan (DoD contracts).

Code of Federal Regulations, 2013 CFR

2013-10-01

... clause— Historically black colleges and universities means institutions determined by the Secretary of... institution that was an integral part of such a college or university before November 14, 1986. Minority... clause, includes historically black colleges and universities and minority institutions, in addition to...

48 CFR 252.219-7003 - Small business subcontracting plan (DoD contracts).

Code of Federal Regulations, 2012 CFR

2012-10-01

... clause— Historically black colleges and universities means institutions determined by the Secretary of... institution that was an integral part of such a college or university before November 14, 1986. Minority... clause, includes historically black colleges and universities and minority institutions, in addition to...

Beyond Flash Gordon and "Star Wars": Science Fiction and History Instruction

ERIC Educational Resources Information Center

Cooper, B. Lee

1978-01-01

Historical concepts can be taught through analysis of science fiction. Offers a class outline with science fiction resources to examine the boundaries of historical inquiry; six themes for student investigation based on specific resources; and a bibliography of 44 additional anthologies and books. (AV)

Role of adsorption in liquid lubrication

NASA Technical Reports Server (NTRS)

Groszek, A. J.

1973-01-01

Changes at solid-liquid interfaces caused by adsorption from solution are discussed paying attention to the following aspects: (1) stability of adsorbed films and the structure of metal-additive-film-liquid interface and effect of adsorbate orientation. (2) chemical versus physical adsorption, (3) heat of adsorption, (4) adsorption of additives, (5) activated adsorption, effect of activating adsorbates, (6) displacement phenomena at solid-liquid interfaces, (7) competition of antiwear additives, their solvents, and water, (8) effect of adsorption on the orientation of liquid in the interfacial region, and (9) relation between the chemical nature of solid surfaces and their interaction with liquid lubricants. The relevance of the above adsorption phenomena to lubrication is discussed, referring where possible to specific examples.

High-resolution endoscopic ultrasound imaging and the number of needle passages are significant factors predicting high yield of endoscopic ultrasound-guided fine needle aspiration for pancreatic solid masses without an on-site cytopathologist

PubMed Central

Jeong, Seok Hoo; Yoon, Hyun Hwa; Kim, Eui Joo; Kim, Yoon Jae; Kim, Yeon Suk; Cho, Jae Hee

2017-01-01

Abstract Endoscopic ultrasound-guided fine needle aspiration (EUS-FNA) is the accurate diagnostic method for pancreatic masses and its accuracy is affected by various FNA methods and EUS equipment. Therefore, we aimed to elucidate the instrumental and methodologic factors for determining the diagnostic yield of EUS-FNA for pancreatic solid masses without an on-site cytopathology evaluation. We retrospectively reviewed the medical records of 260 patients (265 pancreatic solid masses) who underwent EUS-FNA. We compared historical conventional EUS groups with high-resolution imaging devices and finally analyzed various factors affecting EUS-FNA accuracy. In total, 265 pancreatic solid masses of 260 patients were included in this study. The accuracy, sensitivity, specificity, positive predictive value, and negative predictive value of EUS-FNA for pancreatic solid masses without on-site cytopathology evaluation were 83.4%, 81.8%, 100.0%, 100.0%, and 34.3%, respectively. In comparison with conventional image group, high-resolution image group showed the increased accuracy, sensitivity and specificity of EUS-FNA (71.3% vs 92.7%, 68.9% vs 91.9%, and 100% vs 100%, respectively). On the multivariate analysis with various instrumental and methodologic factors, high-resolution imaging (P = 0.040, odds ratio = 3.28) and 3 or more needle passes (P = 0.039, odds ratio = 2.41) were important factors affecting diagnostic yield of pancreatic solid masses. High-resolution imaging and 3 or more passes were the most significant factors influencing diagnostic yield of EUS-FNA in patients with pancreatic solid masses without an on-site cytopathologist. PMID:28079803

Interfacial phonon scattering and transmission loss in >1 μm thick silicon-on-insulator thin films

NASA Astrophysics Data System (ADS)

Jiang, Puqing; Lindsay, Lucas; Huang, Xi; Koh, Yee Kan

2018-05-01

Scattering of phonons at boundaries of a crystal (grains, surfaces, or solid/solid interfaces) is characterized by the phonon wavelength, the angle of incidence, and the interface roughness, as historically evaluated using a specularity parameter p formulated by Ziman [Electrons and Phonons (Clarendon Press, Oxford, 1960)]. This parameter was initially defined to determine the probability of a phonon specularly reflecting or diffusely scattering from the rough surface of a material. The validity of Ziman's theory as extended to solid/solid interfaces has not been previously validated. To better understand the interfacial scattering of phonons and to test the validity of Ziman's theory, we precisely measured the in-plane thermal conductivity of a series of Si films in silicon-on-insulator (SOI) wafers by time-domain thermoreflectance (TDTR) for a Si film thickness range of 1-10 μm and a temperature range of 100-300 K. The Si /SiO2 interface roughness was determined to be 0.11 ±0.04 nm using transmission electron microscopy (TEM). Furthermore, we compared our in-plane thermal conductivity measurements to theoretical calculations that combine first-principles phonon transport with Ziman's theory. Calculations using Ziman's specularity parameter significantly overestimate values from the TDTR measurements. We attribute this discrepancy to phonon transmission through the solid/solid interface into the substrate, which is not accounted for by Ziman's theory for surfaces. The phonons that are specularly transmitted into an amorphous layer will be sufficiently randomized by the time they come back to the crystalline Si layer, the effect of which is practically equivalent to a diffuse reflection at the interface. We derive a simple expression for the specularity parameter at solid/amorphous interfaces and achieve good agreement between calculations and measurement values.

Effects of aluminum and iron nanoparticle additives on composite AP/HTPB solid propellant regression rate

NASA Astrophysics Data System (ADS)

Styborski, Jeremy A.

This project was started in the interest of supplementing existing data on additives to composite solid propellants. The study on the addition of iron and aluminum nanoparticles to composite AP/HTPB propellants was conducted at the Combustion and Energy Systems Laboratory at RPI in the new strand-burner experiment setup. For this study, a large literature review was conducted on history of solid propellant combustion modeling and the empirical results of tests on binders, plasticizers, AP particle size, and additives. The study focused on the addition of nano-scale aluminum and iron in small concentrations to AP/HTPB solid propellants with an average AP particle size of 200 microns. Replacing 1% of the propellant's AP with 40-60 nm aluminum particles produced no change in combustive behavior. The addition of 1% 60-80 nm iron particles produced a significant increase in burn rate, although the increase was lesser at higher pressures. These results are summarized in Table 2. The increase in the burn rate at all pressures due to the addition of iron nanoparticles warranted further study on the effect of concentration of iron. Tests conducted at 10 atm showed that the mean regression rate varied with iron concentration, peaking at 1% and 3%. Regardless of the iron concentration, the regression rate was higher than the baseline AP/HTPB propellants. These results are summarized in Table 3.

Sustainable Materials Management (SMM) - Materials and Waste Management in the United States Key Facts and Figures

EPA Pesticide Factsheets

Each year EPA produces a report called Advancing Sustainable Materials Management: Facts and Figures. It includes information on municipal solid waste (MSW) generation, recycling, composting, combustion with energy recovery and landfilling. The 2014 report provides information on historical tipping fees for MSW, and information on the construction and demolition debris generation, which is outside of the scope of MSW. The Facts and Figures website includes recent reports (2012 to 2014 as well as historical information on materials in the U.S. Municipal Waste Stream, 1960 to 2014 (in tons). The reports for both current and historical waste prevention can be accessed at EPA's SMM website. The recent Annual Facts and Figures reports are accessible at the following link: https://www.epa.gov/smm/advancing-sustainable-materials-management-facts-and-figures-report. Historical data as well as studies and summary tables related to the Advancing Sustainable Materials Management Report are accessible here: https://www.epa.gov/smm/studies-summary-tables-and-data-related-advancing-sustainable-materials-management-report. An excel file containing the data from 1960 - 2014 is located here: https://edg.epa.gov/data/PUBLIC/OLEM/Materials_Municipal_Waste_Stream_1960_to_2014.xlsx. EPA also maintains a list of state and local waste characterization studies (reports are not available for all states). You can search for your state at https://www.epa.gov/smm/advancing-

Synthesis of azines in solid state: reactivity of solid hydrazine with aldehydes and ketones.

PubMed

Lee, Byeongno; Lee, Kyu Hyung; Cho, Jaeheung; Nam, Wonwoo; Hur, Nam Hwi

2011-12-16

Highly conjugated azines were prepared by solid state grinding of solid hydrazine and carbonyl compounds such as aldehydes and ketones, using a mortar and a pestle. Complete conversion to the azine product is generally achieved at room temperature within 24 h, without using solvents or additives. The solid-state reactions afford azines as the sole products with greater than 97% yield, producing only water and carbon dioxide as waste.

Solid matrix transformation and tracer addition using molten ammonium bifluoride salt as a sample preparation method for laser ablation inductively coupled plasma mass spectrometry.

PubMed

Grate, Jay W; Gonzalez, Jhanis J; O'Hara, Matthew J; Kellogg, Cynthia M; Morrison, Samuel S; Koppenaal, David W; Chan, George C-Y; Mao, Xianglei; Zorba, Vassilia; Russo, Richard E

2017-09-08

Solid sampling and analysis methods, such as laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), are challenged by matrix effects and calibration difficulties. Matrix-matched standards for external calibration are seldom available and it is difficult to distribute spikes evenly into a solid matrix as internal standards. While isotopic ratios of the same element can be measured to high precision, matrix-dependent effects in the sampling and analysis process frustrate accurate quantification and elemental ratio determinations. Here we introduce a potentially general solid matrix transformation approach entailing chemical reactions in molten ammonium bifluoride (ABF) salt that enables the introduction of spikes as tracers or internal standards. Proof of principle experiments show that the decomposition of uranium ore in sealed PFA fluoropolymer vials at 230 °C yields, after cooling, new solids suitable for direct solid sampling by LA. When spikes are included in the molten salt reaction, subsequent LA-ICP-MS sampling at several spots indicate that the spikes are evenly distributed, and that U-235 tracer dramatically improves reproducibility in U-238 analysis. Precisions improved from 17% relative standard deviation for U-238 signals to 0.1% for the ratio of sample U-238 to spiked U-235, a factor of over two orders of magnitude. These results introduce the concept of solid matrix transformation (SMT) using ABF, and provide proof of principle for a new method of incorporating internal standards into a solid for LA-ICP-MS. This new approach, SMT-LA-ICP-MS, provides opportunities to improve calibration and quantification in solids based analysis. Looking forward, tracer addition to transformed solids opens up LA-based methods to analytical methodologies such as standard addition, isotope dilution, preparation of matrix-matched solid standards, external calibration, and monitoring instrument drift against external calibration standards.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chiang, Yet-Ming; Carter, Craig W.; Ho, Bryan Y.

Redox flow devices are described in which at least one of the positive electrode or negative electrode-active materials is a semi-solid or is a condensed ion-storing electroactive material, and in which at least one of the electrode-active materials is transported to and from an assembly at which the electrochemical reaction occurs, producing electrical energy. The electronic conductivity of the semi-solid is increased by the addition of conductive particles to suspensions and/or via the surface modification of the solid in semi-solids (e.g., by coating the solid with a more electron conductive coating material to increase the power of the device). Highmore » energy density and high power redox flow devices are disclosed. The redox flow devices described herein can also include one or more inventive design features. In addition, inventive chemistries for use in redox flow devices are also described.« less

75 FR 42460 - Minor Boundary Revision at Lewis and Clark National Historical Park

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-21

... DEPARTMENT OF THE INTERIOR National Park Service Minor Boundary Revision at Lewis and Clark... Clark National Historical Park is modified to include an additional 106.74+/- acres of land identified..., Oregon, immediately adjacent to the southern boundary of the Sunset Beach portion of Lewis and Clark...

18 CFR 300.11 - Technical support for the rate schedule.

Code of Federal Regulations, 2011 CFR

2011-04-01

... historic period or are expected to produce revenue during the rate test period; (B) Capitalized deferred...) Whether the investment is an initial investment, an addition, a replacement, or a capitalized deferred..., Maintenance and Other Annual Expenses. Statement E must contain, for the last five years of the historic...

18 CFR 300.11 - Technical support for the rate schedule.

Code of Federal Regulations, 2010 CFR

2010-04-01

... historic period or are expected to produce revenue during the rate test period; (B) Capitalized deferred...) Whether the investment is an initial investment, an addition, a replacement, or a capitalized deferred..., Maintenance and Other Annual Expenses. Statement E must contain, for the last five years of the historic...

18 CFR 300.11 - Technical support for the rate schedule.

Code of Federal Regulations, 2014 CFR

2014-04-01

... historic period or are expected to produce revenue during the rate test period; (B) Capitalized deferred...) Whether the investment is an initial investment, an addition, a replacement, or a capitalized deferred..., Maintenance and Other Annual Expenses. Statement E must contain, for the last five years of the historic...

18 CFR 300.11 - Technical support for the rate schedule.

Code of Federal Regulations, 2012 CFR

2012-04-01

... historic period or are expected to produce revenue during the rate test period; (B) Capitalized deferred...) Whether the investment is an initial investment, an addition, a replacement, or a capitalized deferred..., Maintenance and Other Annual Expenses. Statement E must contain, for the last five years of the historic...

18 CFR 300.11 - Technical support for the rate schedule.

Code of Federal Regulations, 2013 CFR

2013-04-01

... historic period or are expected to produce revenue during the rate test period; (B) Capitalized deferred...) Whether the investment is an initial investment, an addition, a replacement, or a capitalized deferred..., Maintenance and Other Annual Expenses. Statement E must contain, for the last five years of the historic...

78 FR 72700 - Notice of Inventory Completion: History Colorado, formerly Colorado Historical Society, Denver, CO

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

....R50000] Notice of Inventory Completion: History Colorado, formerly Colorado Historical Society, Denver, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: History Colorado has completed... remains should submit a written request to History Colorado. If no additional requestors come forward...

VIEW OF HISTORIC SLATE SWITCHBOARD IN THE CONTROL ROOM OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF HISTORIC SLATE SWITCHBOARD IN THE CONTROL ROOM OF THE ELWHA POWERHOUSE, INCLUDING: METERS, PROTECTIVE RELAYS, AND SWITCHES. NOTE ADDITION OF PERSONAL COMPUTERS FOR POWER METERING AND OPERATIONS. PHOTO BY JET LOWE, HAER, 1995. - Elwha River Hydroelectric System, Elwha Hydroelectric Dam & Plant, Port Angeles, Clallam County, WA

Urban Science Education: Examining Current Issues through a Historical Lens

ERIC Educational Resources Information Center

McLaughlin, Cheryl A.

2014-01-01

This paper reviews and synthesizes urban science education studies published between 2000 and 2013 with a view to identifying current challenges faced by both teachers and students in urban classrooms. Additionally, this paper considers the historical events that have shaped the conditions, bureaucracies, and interactions of urban institutions.…

Using Counterfactual History to Enhance Students' Historical Understanding

ERIC Educational Resources Information Center

Roberts, Scott L.

2011-01-01

The question "what if?" has been asked by historians for generations. This article explains how history teachers can use students' own what-if questions to enhance their historical knowledge and understanding by offering educators a step-by-step plan for utilizing counterfactual history into their classrooms. Additionally, the author offers a…

A Current Perspective on the Historical Geographic Distribution of the Endangered Muriquis (Brachyteles spp.): Implications for Conservation

PubMed Central

2016-01-01

The muriqui (Brachyteles spp.), endemic to the Atlantic Forest of Brazil, is the largest primate in South America and is endangered, mainly due to habitat loss. Its distribution limits are still uncertain and need to be resolved in order to determine their true conservation status. Species distribution modeling (SDM) has been used to estimate potential species distributions, even when information is incomplete. Here, we developed an environmental suitability model for the two endangered species of muriqui (Brachyteles hypoxanthus and B. arachnoides) using Maxent software. Due to historical absence of muriquis, areas with predicted high habitat suitability yet historically never occupied, were excluded from the predicted historical distribution. Combining that information with the model, it is evident that rivers are potential dispersal barriers for the muriquis. Moreover, although the two species are environmentally separated in a large part of its distribution, there is a potential contact zone where the species apparently do not overlap. This separation might be due to either a physical (i.e., Serra da Mantiqueira mountains) or a biotic barrier (the species exclude one another). Therefore, in addition to environmental characteristics, physical and biotic barriers potentially shaped the limits of the muriqui historical range. Based on these considerations, we proposed the adjustment of their historical distributional limits. Currently only 7.6% of the predicted historical distribution of B. hypoxanthus and 12.9% of B. arachnoides remains forested and able to sustain viable muriqui populations. In addition to measurement of habitat loss we also identified areas for conservation concern where new muriqui populations might be found. PMID:26943910

High-resolution vertical profiles of groundwater electrical conductivity (EC) and chloride from direct-push EC logs

NASA Astrophysics Data System (ADS)

Bourke, Sarah A.; Hermann, Kristian J.; Hendry, M. Jim

2017-11-01

Elevated groundwater salinity associated with produced water, leaching from landfills or secondary salinity can degrade arable soils and potable water resources. Direct-push electrical conductivity (EC) profiling enables rapid, relatively inexpensive, high-resolution in-situ measurements of subsurface salinity, without requiring core collection or installation of groundwater wells. However, because the direct-push tool measures the bulk EC of both solid and liquid phases (ECa), incorporation of ECa data into regional or historical groundwater data sets requires the prediction of pore water EC (ECw) or chloride (Cl-) concentrations from measured ECa. Statistical linear regression and physically based models for predicting ECw and Cl- from ECa profiles were tested on a brine plume in central Saskatchewan, Canada. A linear relationship between ECa/ECw and porosity was more accurate for predicting ECw and Cl- concentrations than a power-law relationship (Archie's Law). Despite clay contents of up to 96%, the addition of terms to account for electrical conductance in the solid phase did not improve model predictions. In the absence of porosity data, statistical linear regression models adequately predicted ECw and Cl- concentrations from direct-push ECa profiles (ECw = 5.48 ECa + 0.78, R 2 = 0.87; Cl- = 1,978 ECa - 1,398, R 2 = 0.73). These statistical models can be used to predict ECw in the absence of lithologic data and will be particularly useful for initial site assessments. The more accurate linear physically based model can be used to predict ECw and Cl- as porosity data become available and the site-specific ECw-Cl- relationship is determined.

Climate impact of anthropogenic aerosols on cirrus clouds

NASA Astrophysics Data System (ADS)

Penner, J.; Zhou, C.

2017-12-01

Cirrus clouds have a net warming effect on the atmosphere and cover about 30% of the Earth's area. Aerosol particles initiate ice formation in the upper troposphere through modes of action that include homogeneous freezing of solution droplets, heterogeneous nucleation on solid particles immersed in a solution, and deposition nucleation of vapor onto solid particles. However, the efficacy with which particles act to form cirrus particles in a model depends on the representation of updrafts. Here, we use a representation of updrafts based on observations of gravity waves, and follow ice formation/evaporation during both updrafts and downdrafts. We examine the possible change in ice number concentration from anthropogenic soot originating from surface sources of fossil fuel and biomass burning and from aircraft particles that have previously formed ice in contrails. Results show that fossil fuel and biomass burning soot aerosols with this version exert a radiative forcing of -0.15±0.02 Wm-2 while aircraft aerosols that have been pre-activated within contrails exert a forcing of -0.20±0.06 Wm-2, but it is possible to decrease these estimates of forcing if a larger fraction of dust particles act as heterogeneous ice nuclei. In addition aircraft aerosols may warm the climate if a large fraction of these particles act as ice nuclei. The magnitude of the forcing in cirrus clouds can be comparable to the forcing exerted by anthropogenic aerosols on warm clouds. This assessment could therefore support climate models with high sensitivity to greenhouse gas forcing, while still allowing the models to fit the overall historical temperature change.

Quantum entanglement at ambient conditions in a macroscopic solid-state spin ensemble.

PubMed

Klimov, Paul V; Falk, Abram L; Christle, David J; Dobrovitski, Viatcheslav V; Awschalom, David D

2015-11-01

Entanglement is a key resource for quantum computers, quantum-communication networks, and high-precision sensors. Macroscopic spin ensembles have been historically important in the development of quantum algorithms for these prospective technologies and remain strong candidates for implementing them today. This strength derives from their long-lived quantum coherence, strong signal, and ability to couple collectively to external degrees of freedom. Nonetheless, preparing ensembles of genuinely entangled spin states has required high magnetic fields and cryogenic temperatures or photochemical reactions. We demonstrate that entanglement can be realized in solid-state spin ensembles at ambient conditions. We use hybrid registers comprising of electron-nuclear spin pairs that are localized at color-center defects in a commercial SiC wafer. We optically initialize 10(3) identical registers in a 40-μm(3) volume (with [Formula: see text] fidelity) and deterministically prepare them into the maximally entangled Bell states (with 0.88 ± 0.07 fidelity). To verify entanglement, we develop a register-specific quantum-state tomography protocol. The entanglement of a macroscopic solid-state spin ensemble at ambient conditions represents an important step toward practical quantum technology.

Cleanliness evaluation of rough surfaces with diffuse IR reflectance

NASA Technical Reports Server (NTRS)

Pearson, L. H.

1995-01-01

Contamination on bonding surfaces has been determined to be a primary cause for degraded bond strength in certain solid rocket motor bondlines. Hydrocarbon and silicone based organic contaminants that are airborne or directly introduced to a surface are a significant source of contamination. Diffuse infrared (IR) reflectance has historically been used as an effective technique for detection of organic contaminants, however, common laboratory methods involving the use of a Fourier transform IR spectrometer (FTIR) are impractical for inspecting the large bonding surface areas found on solid rocket motors. Optical methods involving the use of acousto-optic tunable filters and fixed bandpass optical filters are recommended for increased data acquisition speed. Testing and signal analysis methods are presented which provide for simultaneous measurement of contamination concentration and roughness level on rough metal surfaces contaminated with hydrocarbons.

Historical Inflation Program. A Computer Program Generating Historical Inflation Indices for Army Aircraft. Revision.

DTIC Science & Technology

1984-01-01

data comes in three published formats: (1) a cumulative history coverina past years on a monthly basis, 5 (2) yearly supplements (such as wage and...all fisca. ea’r :. ma. Outzu: _ dNx’resse as monthly, quarterly, fiscal vear, and .-r ear 4n- :~n.e (in calen- dar year 1967 base) and inflation faCt...These indices and factors provide a means of adjusting historical cost data for the procurement of Army aircraft to constant year dollars. Additional

Pre‐historic eating patterns in Latin America and protective effects of plant‐based diets on cardiovascular risk factors

PubMed Central

Acosta Navarro, Julio C; Cárdenas Prado, Silvia M; Cárdenas, Pedro Acosta; Santos, Raul D; Caramelli, Bruno

2010-01-01

In this review, we present the contributions to nutrition science from Latin American native peoples and scientists, appreciated from a historic point of view since pre‐historic times to the modern age. Additionally, we present epidemiological and clinical studies on the area of plant‐based diets and their relation with the prevention and treatment of cardiovascular diseases conducted in recent decades, and we discuss challenges and perspectives regarding aspects of nutrition in the region. PMID:21120310

Mechanical and Combustion Performance of Multi-Walled Carbon Nanotubes as an Additive to Paraffin-Based Solid Fuels for Hybrid Rockets

NASA Technical Reports Server (NTRS)

Larson, Daniel B.; Boyer, Eric; Wachs, Trevor; Kuo, Kenneth, K.; Koo, Joseph H.; Story, George

2012-01-01

Paraffin-based solid fuels for hybrid rocket motor applications are recognized as a fastburning alternative to other fuel binders such as HTPB, but efforts to further improve the burning rate and mechanical properties of paraffin are still necessary. One approach that is considered in this study is to use multi-walled carbon nanotubes (MWNT) as an additive to paraffin wax. Carbon nanotubes provide increased electrical and thermal conductivity to the solid-fuel grains to which they are added, which can improve the mass burning rate. Furthermore, the addition of ultra-fine aluminum particles to the paraffin/MWNT fuel grains can enhance regression rate of the solid fuel and the density impulse of the hybrid rocket. The multi-walled carbon nanotubes also present the possibility of greatly improving the mechanical properties (e.g., tensile strength) of the paraffin-based solid-fuel grains. For casting these solid-fuel grains, various percentages of MWNT and aluminum particles will be added to the paraffin wax. Previous work has been published about the dispersion and mixing of carbon nanotubes.1 Another manufacturing method has been used for mixing the MWNT with a phenolic resin for ablative applications, and the manufacturing and mixing processes are well-documented in the literature.2 The cost of MWNT is a small fraction of single-walled nanotubes. This is a scale-up advantage as future applications and projects will require low cost additives to maintain cost effectiveness. Testing of the solid-fuel grains will be conducted in several steps. Dog bone samples will be cast and prepared for tensile testing. The fuel samples will also be analyzed using thermogravimetric analysis and a high-resolution scanning electron microscope (SEM). The SEM will allow for examination of the solid fuel grain for uniformity and consistency. The paraffin-based fuel grains will also be tested using two hybrid rocket test motors located at the Pennsylvania State University s High Pressure Combustion Lab.

Flood Frequency Analysis With Historical and Paleoflood Information

NASA Astrophysics Data System (ADS)

Stedinger, Jery R.; Cohn, Timothy A.

1986-05-01

An investigation is made of flood quantile estimators which can employ "historical" and paleoflood information in flood frequency analyses. Two categories of historical information are considered: "censored" data, where the magnitudes of historical flood peaks are known; and "binomial" data, where only threshold exceedance information is available. A Monte Carlo study employing the two-parameter lognormal distribution shows that maximum likelihood estimators (MLEs) can extract the equivalent of an additional 10-30 years of gage record from a 50-year period of historical observation. The MLE routines are shown to be substantially better than an adjusted-moment estimator similar to the one recommended in Bulletin 17B of the United States Water Resources Council Hydrology Committee (1982). The MLE methods performed well even when floods were drawn from other than the assumed lognormal distribution.

DPAL: Historical Perspective And Summary Of Achievements

DTIC Science & Technology

2013-08-20

of a gas gain medium. The thermal effects existing, for example, in solid state lasers cause aberrations and thermal lensing that degrade the beam...and 500 torr of ethane buffer gas had windows AR coated on both sides (external and internal) and was kept at 98°C. The pump and lasing beams were...back mirror. A 2 cm long cell with antireflection coated windows was filled with metallic cesium and 500 Torr ethane and placed in a heated oven with a

A Study of the Relationship between Worker Attitudes and Organizational Effectiveness in Base Level Environmental and Contract Planning Sections.

DTIC Science & Technology

1980-06-01

and water pollution are not the only areas of recent environmental concern and congressional legislation. The effects of solid waste, pesticides , noise...41:Section 4). Pesticide use has historically been a major contributor to human welfare (25:167). It has been estimated that a ban on the use of all... pesticides would result in a 25 to 30 per- cent reduction in U.S. crop and livestock yields. Unfortunately, the widespread use of pesticides has not

Significance and implications of FDA approval of pembrolizumab for biomarker-defined disease.

PubMed

Boyiadzis, Michael M; Kirkwood, John M; Marshall, John L; Pritchard, Colin C; Azad, Nilofer S; Gulley, James L

2018-05-14

The U.S. Food and Drug Administration (FDA) recently approved pembrolizumab, an anti- programmed cell death protein 1 cancer immunotherapeutic, for use in advanced solid tumors in patients with the microsatellite-high/DNA mismatch repair-deficient biomarker. This is the first example of a tissue-agnostic FDA approval of a treatment based on a patient's tumor biomarker status, rather than on tumor histology. Here we discuss key issues and implications arising from the biomarker-based disease classification implied by this historic approval.

Methods to Identify Changes in Background Water-Quality Conditions Using Dissolved-Solids Concentrations and Loads as Indicators, Arkansas River and Fountain Creek, in the Vicinity of Pueblo, Colorado

USGS Publications Warehouse

Ortiz, Roderick F.

2004-01-01

Effective management of existing water-storage capacity in the Arkansas River Basin is anticipated to help satisfy the need for water in southeastern Colorado. A strategy to meet these needs has been developed, but implementation could affect the water quality of the Arkansas River and Fountain Creek in the vicinity of Pueblo, Colorado. Because no known methods are available to determine what effects future changes in operations will have on water quality, the U.S. Geological Survey, in cooperation with the Southeastern Colorado Water Activity Enterprise, began a study in 2002 to develop methods that could identify if future water-quality conditions have changed significantly from background (preexisting) water-quality conditions. A method was developed to identify when significant departures from background (preexisting) water-quality conditions occur in the lower Arkansas River and Fountain Creek in the vicinity of Pueblo, Colorado. Additionally, the methods described in this report provide information that can be used by various water-resource agencies for an internet-based decision-support tool. Estimated dissolved-solids concentrations at five sites in the study area were evaluated to designate historical background conditions and to calculate tolerance limits used to identify statistical departures from background conditions. This method provided a tool that could be applied with defined statistical probabilities associated with specific tolerance limits. Drought data from 2002 were used to test the method. Dissolved-solids concentrations exceeded the tolerance limits at all four sites on the Arkansas River at some point during 2002. The number of exceedances was particularly evident when streamflow from Pueblo Reservoir was reduced, and return flows and ground-water influences to the river were more prevalent. No exceedances were observed at the site on Fountain Creek. These comparisons illustrated the need to adjust the concentration data to account for varying streamflow. As such, similar comparisons between flow-adjusted data were done. At the site Arkansas River near Avondale, nearly all the 2002 flow-adjusted concentration data were less than the flow-adjusted tolerance limit which illustrated the effects of using flow-adjusted concentrations. Numerous exceedances of the flow-adjusted tolerance limits, however, were observed at the sites Arkansas River above Pueblo and Arkansas River at Pueblo. These results indicated that the method was able to identify a change in the ratio of source waters under drought conditions. Additionally, tolerance limits were calculated for daily dissolved-solids load and evaluated in a similar manner. Several other mass-load approaches were presented to help identify long-term changes in water quality. These included comparisons of cumulative mass load at selected sites and comparisons of mass load contributed at the Arkansas River near Avondale site by measured and unmeasured sources.

The analysis of the statistical and historical information gathered during the development of the Shuttle Orbiter Primary Flight Software

NASA Technical Reports Server (NTRS)

Simmons, D. B.; Marchbanks, M. P., Jr.; Quick, M. J.

1982-01-01

The results of an effort to thoroughly and objectively analyze the statistical and historical information gathered during the development of the Shuttle Orbiter Primary Flight Software are given. The particular areas of interest include cost of the software, reliability of the software, requirements for the software and how the requirements changed during development of the system. Data related to the current version of the software system produced some interesting results. Suggestions are made for the saving of additional data which will allow additional investigation.

Biodiversity of freshwater diatom communities during 1000 years of metal mining, land use, and climate change in central Sweden.

PubMed

De Laender, F; Verschuren, D; Bindler, R; Thas, O; Janssen, C R

2012-08-21

We subjected a unique set of high-quality paleoecological data to statistical modeling to examine if the biological richness and evenness of freshwater diatom communities in the Falun area, a historical copper (Cu) mining region in central Sweden, was negatively influenced by 1000 years of metal exposure. Contrary to ecotoxicological predictions, we found no negative relation between biodiversity and the sedimentary concentrations of eight metals. Strikingly, our analysis listed metals (Co, Fe, Cu, Zn, Cd, Pb) or the fractional land cover of cultivated crops, meadow, and herbs indicating land disturbance as potentially promoting biodiversity. However, correlation between metal- and land-cover trends prevented concluding which of these two covariate types positively affected biodiversity. Because historical aqueous metal concentrations--inferred from solid-water partitioning--approached experimental toxicity thresholds for freshwater algae, positive effects of metal mining on biodiversity are unlikely. Instead, the positive relationship between biodiversity and historical land-cover change can be explained by the increasing proportion of opportunistic species when anthropogenic disturbance intensifies. Our analysis illustrates that focusing on the direct toxic effects of metals alone may yield inaccurate environmental assessments on time scales relevant for biodiversity conservation.

High energy density redox flow device

DOEpatents

Chiang, Yet-Ming; Carter, W. Craig; Ho, Bryan Y; Duduta, Mihai; Limthongkul, Pimpa

2014-05-13

Redox flow devices are described in which at least one of the positive electrode or negative electrode-active materials is a semi-solid or is a condensed ion-storing electroactive material, and in which at least one of the electrode-active materials is transported to and from an assembly at which the electrochemical reaction occurs, producing electrical energy. The electronic conductivity of the semi-solid is increased by the addition of conductive particles to suspensions and/or via the surface modification of the solid in semi-solids (e.g., by coating the solid with a more electron conductive coating material to increase the power of the device). High energy density and high power redox flow devices are disclosed. The redox flow devices described herein can also include one or more inventive design features. In addition, inventive chemistries for use in redox flow devices are also described.

ACHP | News

Science.gov Websites

Increase in Historic Preservation Fund, Among Other Items The President's FY 2016 budget seeks $89.9 million for the Historic Preservation Fund, an increase of $33.5 million over FY 2015. The bulk of the increase is for a Civil Rights initiative, including the addition of $2.5 million for grants to

75 FR 76008 - Agency Information Collection Activities; Proposed Collection; Comment Request; Additional...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... (44 U.S.C. 3501-3520), Federal Agencies must obtain approval from the Office of Management and Budget... is required to maintain an historical file containing the labeling and advertisements in use on the.... The owner or operator must maintain in the historical file any labeling or advertisements in which a...

4. Photocopy of measured drawing (from Robert R. Harvey's 'Historic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Photocopy of measured drawing (from Robert R. Harvey's 'Historic Stone Architecture of Winterset, Iowa, Prior To and During the Civil War Period,' Unpublished Report, Iowa State University, (Ames, IA), 1960.) FLOOR PLAN, THIRD ADDITION ('Fig. 5-D') - J. G. Vawter House, First Avenue & South Street, Winterset, Madison County, IA

3. Photocopy of measured drawing (from Robert R. Harvey's 'Historic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Photocopy of measured drawing (from Robert R. Harvey's 'Historic Stone Architecture of Winterset, Iowa, Prior To and During the Civil War Period,' Unpublished Report, Iowa State University, (Ames, IA), 1960.) FLOOR PLAN, SECOND ADDITION ('Fig. 5-C') - J. G. Vawter House, First Avenue & South Street, Winterset, Madison County, IA

2. Photocopy of measured drawing (from Robert R. Harvey's 'Historic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Photocopy of measured drawing (from Robert R. Harvey's 'Historic Stone Architecture of Winterset, Iowa, Prior To and During the Civil War Period,' Unpublished Report, Iowa State University, (Ames, IA), 1960.) FLOOR PLAN, SHOWING FIRST ADDITION ('Fig. 5-B') - J. G. Vawter House, First Avenue & South Street, Winterset, Madison County, IA

Simulation of a dynamical ecotourism system with low carbon activity: A case from western China.

PubMed

He, Yuan; Huang, Ping; Xu, Hong

2018-01-15

Currently, sustainable tourism is becoming more and more important in developing ecological economies. To achieve low-carbon development, some industries, such as logistics and municipal solid waste, have already taken action, but tourism has not attached sufficient importance to this issue. This paper designs an ecotourism system including tourism, carbon waste (solid waste and sewage), and ecology (water supply and green areas) to simulate low-carbon ecotourism through a quantitative approach. This paper explores the tourism system as well as some interactive factors and studies their quantitative relationship based on historical data. A feedback-loop dynamical system model is designed to simulate tourism, waste carbon, and ecology simultaneously. Finally, a case study applying the feedback-loop dynamical system model to Leshan City, a typical travel destination with colorful natural resources in western China, is conducted to indicate the development of ecotourism in an environmentally friendly economy, which verifies the positive effects of the model. Results show a coordinating upward tendency of tourism, solid waste carbon, and ecology from the dynamical model. When tourism increases, solid waste accumulation increases; however, the amount of sewage dumped directly into nature decreases sharply. After analysis of investment policy scenarios, the research indicates that more funds for sewage treatment will attract more tourists. To maintain the equilibrium of carbon waste, more funds shall be invested in solid waste treatment in the long term. Some discussions about local policy are included. Copyright © 2017 Elsevier Ltd. All rights reserved.

Photogrammetric Analysis of Historical Image Repositories for Virtual Reconstruction in the Field of Digital Humanities

NASA Astrophysics Data System (ADS)

Maiwald, F.; Vietze, T.; Schneider, D.; Henze, F.; Münster, S.; Niebling, F.

2017-02-01

Historical photographs contain high density of information and are of great importance as sources in humanities research. In addition to the semantic indexing of historical images based on metadata, it is also possible to reconstruct geometric information about the depicted objects or the camera position at the time of the recording by employing photogrammetric methods. The approach presented here is intended to investigate (semi-) automated photogrammetric reconstruction methods for heterogeneous collections of historical (city) photographs and photographic documentation for the use in the humanities, urban research and history sciences. From a photogrammetric point of view, these images are mostly digitized photographs. For a photogrammetric evaluation, therefore, the characteristics of scanned analog images with mostly unknown camera geometry, missing or minimal object information and low radiometric and geometric resolution have to be considered. In addition, these photographs have not been created specifically for documentation purposes and so the focus of these images is often not on the object to be evaluated. The image repositories must therefore be subjected to a preprocessing analysis of their photogrammetric usability. Investigations are carried out on the basis of a repository containing historical images of the Kronentor ("crown gate") of the Dresden Zwinger. The initial step was to assess the quality and condition of available images determining their appropriateness for generating three-dimensional point clouds from historical photos using a structure-from-motion evaluation (SfM). Then, the generated point clouds were assessed by comparing them with current measurement data of the same object.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirka, Michael M.; Nandwana, Peeyush; Lee, Yousub

Additive manufacturing (AM) of metals is rapidly emerging as an established manufacturing process for metal components. Unlike traditional metals fabrication processes, metals fabricated via AM undergo localized thermal cycles during fabrication. As a result, AM presents the opportunity to control the liquid-solid phase transformation, i.e. material texture. But, thermal cycling presents challenges from the standpoint of solid-solid phase transformations. We will discuss the opportunities and challenges in metals AM in the context of texture control and associated solid-solid phase transformations in Ti-6Al-4V and Inconel 718.

Analysis of landfills with historic airphotos

NASA Technical Reports Server (NTRS)

Erb, T. L.; Philipson, W. R.; Teng, W. L.; Liang, T.

1981-01-01

An investigation is conducted regarding the value of existing aerial photographs for waste management, including landfill monitoring. The value of historic aerial photographs for documenting landfill boundaries is shown in a graph in which the expansion of an active landfill is traced over a 40-year period. Historic aerial photographs can also be analyzed to obtain general or detailed land-use and land-cover information. In addition, the photographs provide information regarding other elements of the physical environment, including geology, soils, and surface and subsurface drainage. The value of historic photos is discussed, taking into account applications for inventory, assessing contamination/health hazards, planning corrective measures, planning waste collection and facilities, developing inactive landfills, and research concerning improved land-filling operations.

Thermal-Flow Code for Modeling Gas Dynamics and Heat Transfer in Space Shuttle Solid Rocket Motor Joints

NASA Technical Reports Server (NTRS)

Wang, Qunzhen; Mathias, Edward C.; Heman, Joe R.; Smith, Cory W.

2000-01-01

A new, thermal-flow simulation code, called SFLOW. has been developed to model the gas dynamics, heat transfer, as well as O-ring and flow path erosion inside the space shuttle solid rocket motor joints by combining SINDA/Glo, a commercial thermal analyzer. and SHARPO, a general-purpose CFD code developed at Thiokol Propulsion. SHARP was modified so that friction, heat transfer, mass addition, as well as minor losses in one-dimensional flow can be taken into account. The pressure, temperature and velocity of the combustion gas in the leak paths are calculated in SHARP by solving the time-dependent Navier-Stokes equations while the heat conduction in the solid is modeled by SINDA/G. The two codes are coupled by the heat flux at the solid-gas interface. A few test cases are presented and the results from SFLOW agree very well with the exact solutions or experimental data. These cases include Fanno flow where friction is important, Rayleigh flow where heat transfer between gas and solid is important, flow with mass addition due to the erosion of the solid wall, a transient volume venting process, as well as some transient one-dimensional flows with analytical solutions. In addition, SFLOW is applied to model the RSRM nozzle joint 4 subscale hot-flow tests and the predicted pressures, temperatures (both gas and solid), and O-ring erosions agree well with the experimental data. It was also found that the heat transfer between gas and solid has a major effect on the pressures and temperatures of the fill bottles in the RSRM nozzle joint 4 configuration No. 8 test.

Idaho National Laboratory Cultural Resource Monitoring Report for 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Julie B.

2013-10-01

This report describes the cultural resource monitoring activities of the Idaho National Laboratory’s (INL) Cultural Resource Management (CRM) Office during 2013. Throughout the year, thirty-eight cultural resource localities were revisited including: two locations with Native American human remains, one of which is also a cave; fourteen additional caves; seven prehistoric archaeological sites ; four historic archaeological sites; one historic trail; one nuclear resource (Experimental Breeder Reactor-I, a designated National Historic Landmark); and nine historic structures located at the Central Facilities Area. Of the monitored resources, thirty-three were routinely monitored, and five were monitored to assess project compliance with cultural resourcemore » recommendations along with the effects of ongoing project activities. On six occasions, ground disturbing activities within the boundaries of the Power Burst Facility/Critical Infrastructure Test Range Complex (PBF/CITRC) were observed by INL CRM staff prepared to respond to any additional finds of Native American human remains. In addition, two resources were visited more than once as part of the routine monitoring schedule or to monitor for additional damage. Throughout the year, most of the cultural resources monitored had no visual adverse changes resulting in Type 1determinations. However, Type 2 impacts were noted at eight sites, indicating that although impacts were noted or that a project was operating outside of culturally cleared limitations, cultural resources retained integrity and noted impacts did not threaten National Register eligibility. No new Type 3 or any Type 4 impacts that adversely impacted cultural resources and threatened National Register eligibility were observed at cultural resources monitored in 2013.« less

Comparison of analytical tools appropriate for identification of proteinaceous additives in historical mortars.

PubMed

Krizova, Iva; Schultz, Julia; Nemec, Ivan; Cabala, Radomir; Hynek, Radovan; Kuckova, Stepanka

2018-01-01

Natural organic additives such as eggs, lard, resins, and oils have been added to mortars since ancient times, because the ancient builders knew of their positive effect on the mortar quality. The tradition of adding organic materials to mortars was commonly handed down only verbally for thousands years. However, this practice disappeared in the nineteenth century, when the usage of modern materials started. Today, one of the most recent topics in the industry of building materials is the reusing of natural organic materials and searching for the forgotten ancient recipes. The research of the old technological approaches involves currently the most advanced analytical techniques and methods. This paper is focussed on testing the possibility of identification of proteinaceous additives in historical mortars and model mortar samples containing blood, bone glue, curd, eggs and gelatine, by Fourier transform infrared (FTIR) and Raman spectroscopy, gas chromatography - mass spectrometry (GC-MS), matrix-assisted laser desorption/ionisation-time of flight mass spectrometry (MALDI-TOF MS), liquid chromatography-electrospray ionisation-quadrupole-time of flight mass spectrometry (LC-ESI-Q-TOF MS) and enzyme-linked immunosorbent assay (ELISA). All these methods were applied to the mortar sample taken from the interior of the medieval (sixteenth century) castle in Namest nad Oslavou in the Czech Republic and their comparison contributed to the rough estimation of the protein additive content in the mortar. The obtained results demonstrate that only LC-ESI-Q-TOF MS, MALDI-TOF MS and ELISA have the sufficiently low detection limits that enable the reliable identification of collagens in historical mortars. Graphical abstract Proteomics analyses of historical mortars.

Preparation and in Vivo Evaluation of a Dutasteride-Loaded Solid-Supersaturatable Self-Microemulsifying Drug Delivery System

PubMed Central

Kim, Min-Soo; Ha, Eun-Sol; Choo, Gwang-Ho; Baek, In-Hwan

2015-01-01

The purpose of this study was to prepare a dutasteride-loaded solid-supersaturatable self-microemulsifying drug delivery system (SMEDDS) using hydrophilic additives with high oral bioavailability, and to determine if there was a correlation between the in vitro dissolution data and the in vivo pharmacokinetic parameters of this delivery system in rats. A dutasteride-loaded solid-supersaturatable SMEDDS was generated by adsorption of liquid SMEDDS onto Aerosil 200 colloidal silica using a spray drying process. The dissolution and oral absorption of dutasteride from solid SMEDDS significantly increased after the addition of hydroxypropylmethyl cellulose (HPMC) or Soluplus. Solid SMEDDS/Aerosil 200/Soluplus microparticles had higher oral bioavailability with 6.8- and 5.0-fold higher peak plasma concentration (Cmax) and area under the concentration-time curve (AUC) values, respectively, than that of the equivalent physical mixture. A linear correlation between in vitro dissolution efficiency and in vivo pharmacokinetic parameters was demonstrated for both AUC and Cmax values. Therefore, the preparation of a solid-supersaturatable SMEDDS with HPMC or Soluplus could be a promising formulation strategy to develop novel solid dosage forms of dutasteride. PMID:25984604

Bioremediation of diesel fuel contaminated soil: effect of non ionic surfactants and selected bacteria addition.

PubMed

Collina, Elena; Lasagni, Marina; Pitea, Demetrio; Franzetti, Andrea; Di Gennaro, Patrizia; Bestetti, Giuseppina

2007-09-01

Aim of this work was to evaluate influence of two commercial surfactants and inoculum of selected bacteria on biodegradation of diesel fuel in different systems. Among alkyl polyethossilates (Brij family) and sorbitan derivates (Tween family) a first selection of surfactants was performed by estimation of Koc and Dafnia magna EC50 with molecular descriptor and QSAR model. Further experiments were conducted to evaluate soil sorption, biodegradability and toxicity. In the second part of the research, the effect of Brij 56, Tween 80 and selected bacteria addition on biodegradation of diesel fuel was studied in liquid cultures and in slurry and solid phase systems. The latter experiments were performed with diesel contaminated soil in bench scale slurry phase bioreactor and solid phase columns. Tween 80 addition increased the biodegradation rate of hydrocarbons both in liquid and in slurry phase systems. Regarding the effect of inoculum, no enhancement of biodegradation rate was observed neither in surfactant added nor in experiments without addition. On the contrary, in solid phase experiments, inoculum addition resulted in enhanced biodegradation compared to surfactant addition.

Quality of ground water in southeastern and south-central Washington, 1982

USGS Publications Warehouse

Turney, G.L.

1986-01-01

In 1982 groundwater was sampled at over 100 sites in the southeastern-south central region of Washington and analyzed for pH, specific conductance, and concentrations of fecal-coliform bacteria, major dissolved irons, and dissolved iron, manganese, and nitrate. Twenty percent of the samples were analyzed for concentrations of dissolved aluminum, arsenic, barium, cadmium, chromium, cooper, lead, mercury, selenium, silver, and zinc. The predominant water type was calcium bicarbonate. Some sodium bicarbonate water was found in samples from the Lower Yakima, Horse Heaven Hills, and Walla Walla-Tucannon subregions. Dissolved solids concentrations were typically less than 500 mg/L (milligrams per liter). Median iron and manganese concentrations were less than 20 micrograms/L except in the Palouse subregion, where the median concentration of iron was 200 micrograms/L and the median concentrations of manganese was 45 micrograms/L. Generally, trace-metal concentrations were also less than 10 micrograms/L except for barium, copper, and zinc. Nitrate concentrations were less than 1.0 mg/L in waters from half the wells sampled. Concentrations greater than 5.0 mg/L were found in areas of the Lower Yakima, Walla Walla-Tucannon and Hanford subregions. No fecal-coliform bacteria were detected. U.S. Environmental Protection Agency drinking water regulation limits were generally not exceeded, except for occasional high concentrations of nitrate or dissolved solids. The historical data for the region were evaluated for these same constituents. Quantitative differences were found, but the historical and 1982 data led to similar qualitative conclusions. (USGS)

Impact Verification of Aerogel Insulation Paint on Historic Brick Facades

NASA Astrophysics Data System (ADS)

Ganobjak, Michal; Kralova, Eva

2017-10-01

Increasing the sustainability of existing buildings is being motivated by reduction of their energy demands. It is the above all the building envelope and its refurbishment by substitution or addition of new materials that makes the opportunity for reduction of energy consumption. A special type of refurbishment is conservation of historical buildings. Preservation of historic buildings permits also application of innovative methods and materials in addition to the original materials if their effects are known and the gained experience ensures their beneficial effect. On the market, there are new materials with addition of silica aerogel in various forms of products. They are also potentially useful in conservation of monuments. However, the effects of aerogel application in these cases are not known. For refurbishment is commercially available additional transparent insulation paint - Nansulate Clear Coat which is containing aerogel and can be used for structured surfaces such as bricks. A series of experiments examined the thermo-physical manifestation of an ultra-thin insulation coating of Nansulate Clear Coat containing silica aerogel on a brick facade. The experiments of active and passive thermography have observed effects of application on the small-scale samples of the brick façade of a protected historical building. Through a series of experiments were measured thermal insulation effect and influence on the aesthetic characteristics such as change in colour and gloss. The treated samples were compared to a reference. Results have shown no thermal-insulating manifestation of the recommended three layers of insulation paint. The three layers recommended by the manufacturer did not significantly affect the appearance of the brick facade. Color and gloss were not significantly changed. Experiments showed the absence of thermal insulation effect of Nansulate transparent triple coating. The thermal insulation effect could likely be reached by more layers of application, which, on the other hand may be unacceptable on the heritage conservation because of number of applications, time demand and financial costs. The effects of multiple layers on heritage attributes were not researched. Extrapolating the measured results, it can be expected that application of more than three layers of paint can significantly affect the aesthetic characteristics of the monument such as gloss and colours of historic brick facades. Due to specific material consistence of historic architecture and new insulation paint materials on the market, it is recommended to provide independent laboratory testing and on-site tests on facades of historic buildings in cooperation with the Monument Protection Board.

The market value of cultural heritage in urban areas: an application of spatial hedonic pricing

NASA Astrophysics Data System (ADS)

Lazrak, Faroek; Nijkamp, Peter; Rietveld, Piet; Rouwendal, Jan

2014-01-01

The current literature often values intangible goods like cultural heritage by applying stated preference methods. In recent years, however, the increasing availability of large databases on real estate transactions and listed prices has opened up new research possibilities and has reduced various existing barriers to applications of conventional (spatial) hedonic analysis to the real estate market. The present paper provides one of the first applications using a spatial autoregressive model to investigate the impact of cultural heritage—in particular, listed buildings and historic-cultural sites (or historic landmarks)—on the value of real estate in cities. In addition, this paper suggests a novel way of specifying the spatial weight matrix—only prices of sold houses influence current price—in identifying the spatial dependency effects between sold properties. The empirical application in the present study concerns the Dutch urban area of Zaanstad, a historic area for which over a long period of more than 20 years detailed information on individual dwellings, and their market prices are available in a GIS context. In this paper, the effect of cultural heritage is analysed in three complementary ways. First, we measure the effect of a listed building on its market price in the relevant area concerned. Secondly, we investigate the value that listed heritage has on nearby property. And finally, we estimate the effect of historic-cultural sites on real estate prices. We find that, to purchase a listed building, buyers are willing to pay an additional 26.9 %, while surrounding houses are worth an extra 0.28 % for each additional listed building within a 50-m radius. Houses sold within a conservation area appear to gain a premium of 26.4 % which confirms the existence of a `historic ensemble' effect.

Determinants of bird species richness, endemism, and island network roles in Wallacea and the West Indies: is geography sufficient or does current and historical climate matter?

PubMed Central

Dalsgaard, Bo; Carstensen, Daniel W; Fjeldså, Jon; Maruyama, Pietro K; Rahbek, Carsten; Sandel, Brody; Sonne, Jesper; Svenning, Jens-Christian; Wang, Zhiheng; Sutherland, William J

2014-01-01

Island biogeography has greatly contributed to our understanding of the processes determining species' distributions. Previous research has focused on the effects of island geography (i.e., island area, elevation, and isolation) and current climate as drivers of island species richness and endemism. Here, we evaluate the potential additional effects of historical climate on breeding land bird richness and endemism in Wallacea and the West Indies. Furthermore, on the basis of species distributions, we identify island biogeographical network roles and examine their association with geography, current and historical climate, and bird richness/endemism. We found that island geography, especially island area but also isolation and elevation, largely explained the variation in island species richness and endemism. Current and historical climate only added marginally to our understanding of the distribution of species on islands, and this was idiosyncratic to each archipelago. In the West Indies, endemic richness was slightly reduced on islands with historically unstable climates; weak support for the opposite was found in Wallacea. In both archipelagos, large islands with many endemics and situated far from other large islands had high importance for the linkage within modules, indicating that these islands potentially act as speciation pumps and source islands for surrounding smaller islands within the module and, thus, define the biogeographical modules. Large islands situated far from the mainland and/or with a high number of nonendemics acted as links between modules. Additionally, in Wallacea, but not in the West Indies, climatically unstable islands tended to interlink biogeographical modules. The weak and idiosyncratic effect of historical climate on island richness, endemism, and network roles indicates that historical climate had little effects on extinction-immigration dynamics. This is in contrast to the strong effect of historical climate observed on the mainland, possibly because surrounding oceans buffer against strong climate oscillations and because geography is a strong determinant of island richness, endemism and network roles. PMID:25505528

A Guide to Historical Literature and Other Issues in History Bibliography.

ERIC Educational Resources Information Center

Falk, Joyce Duncan; And Others

In response to a request from the Research Division of the American Historical Association (AHA), the Association for the Bibliography of History (ABH) compiled a report on the options for a new history literature guide and on additional issues in history bibliography. The AHA previously conducted surveys to solicit opinions about the need for a…

Biodiversity in Finnish wilderness areas: Historical and cultural constraints to preserve species and habitats

Treesearch

Anna-Liisa Sippola

2002-01-01

The present status of species and habitats in Finnish wilderness areas is largely a consequence of past administrative, use, and management traditions in northern Finland. The existing wilderness legislation sets a framework for management, but historical uses and administrative decisions have influenced many prevailing practices. In addition, management of many uses...

Globalizing Historically Black Business Schools: A Case Study of the Application of Modern Pedagogical Theories of Internationalizing Higher Education

ERIC Educational Resources Information Center

Kedia, Ben L.; Clampit, Jack; Gaffney, Nolan

2014-01-01

The AACSB and AIB have each issued reports aimed at ensuring the internationalization of business schools. Historically Black Colleges and Universities (HBCUs)--as underresourced entities serving an underprivileged constituency--may need additional attention. Unfortunately, neither the AACSB nor AIB reports mention HBCUs. The broader literature is…

Historical and Political Gazeteer of Afghanistan. Volume 1, Badakhshan Province and Northeastern Afghanistan.

ERIC Educational Resources Information Center

Adamec, Ludwig W., Ed.

Combining the most important geographical data with historical, political, and cultural information, this work, one of six volumes designed as a tool of research and a general reference source, updates and includes a previous publication compiled in 1914 with corrections and additions of maps and considerable new material to take into account…

78 FR 44997 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-25

... historic Rule 144A transaction data, to amend the definition of Historic TRACE Data to reference the three... dissemination of Rule 144A transactions. Nine commenters supported such dissemination and three commenters were... addition, transparency in this sector may improve the quality of the valuation of securities and derivative...

3. Photocopy of measured drawing (from: Harvey, Robert R. 'Historic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Photocopy of measured drawing (from: Harvey, Robert R. 'Historic Stone Architecture of Winterset, Iowa, Prior to and During the Civil War Period.' Ames, IA: Iowa State University, 1960.) Robert R. Harvey, delineator 1960 FLOOR PLAN, ORIGINAL HOUSE PLUS SMOKEHOUSE ADDITION ('FIGURE 3-C') - Caleb Clark House, 814 South Eighth Street, Winterset, Madison County, IA

2. Photocopy of measured drawing (from: Harvey, Robert R. 'Historic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Photocopy of measured drawing (from: Harvey, Robert R. 'Historic Stone Architecture of Winterset, Iowa, Prior to and During the Civil War Period.' Ames, IA: Iowa State University, 1960.) Robert R. Harvey, delineator 1960 FLOOR PLAN, ORIGINAL HOUSE PLUS WELLHOUSE ADDITION ('FIGURE 3-B') - Caleb Clark House, 814 South Eighth Street, Winterset, Madison County, IA

Archives: New Horizons in Astronomy

NASA Astrophysics Data System (ADS)

Bobis, L.; Laurenceau, A.

2010-10-01

The scientific archives in the Paris Observatory's library date back to the XVIIth century. In addition to the preservation and the valorisation of these historic archives, the library is also responsible for the efficient and timely management of contemporary documents to ensure their optimum conservation and identification once they become historical. Oral, iconographic and electronic documents complement these paper archives.

Initial characterization of the groundwater system near the Lower Colorado Water Supply Project, Imperial Valley, California

USGS Publications Warehouse

Coes, Alissa L.; Land, Michael; Densmore, Jill N.; Landrum, Michael T.; Beisner, Kimberly R.; Kennedy, Jeffrey R.; Macy, Jamie P.; Tillman, Fred D.

2015-01-01

During and after lining the All-American Canal (2007–11), groundwater elevations in the Lower Colorado Water Supply Project area declined, while total dissolved solids concentrations remained relatively constant. The total dissolved solids concentrations in well LCWSP-2 ranged from 650 to 800 milligrams per liter during this study. Depth-specific water-quality and isotope sampling at well LCWSP-2 indicated the groundwater pumped from the deeper part of the screened interval (240–280 feet below land surface) contained a greater proportion of historical groundwater than the groundwater pumped from the shallower part of the screened interval (350–385 feet below land surface). Age-tracer data at well LCWSP-2 indicated that all depths of the screened interval had received recent recharge from seepage of Colorado River water from the All-American Canal.

Cathodic Protection Deployment on Space Shuttle Solid Rocket Boosters

NASA Technical Reports Server (NTRS)

Zook, Lee M.

1998-01-01

Corrosion protection of the space shuttle solid rocket boosters incorporates the use of cathodic protection(anodes) in concert with several coatings systems. The SRB design has large carbon/carbon composites(motor nozzle) electrically connected to an aluminum alloy structure. Early in the STS program, the aluminum structures incurred tremendous corrosive attack due primarily to the galvanic couple to the carbon/carbon nozzle at coating damage locations. Also contributing to the galvanic corrosion problem were stainless steel and titanium alloy components housed within the aluminum structures and electrically connected to the aluminum structures. This paper will highlight the evolution in the protection of the aluminum structures, providing historical information and summary data from the operation of the corrosion protection systems. Also, data and information will be included regarding the evaluation and deployment of inorganic zinc rich primers as anode area on the aluminum structures.

Towards proteomic analysis of milk proteins in historical building materials

NASA Astrophysics Data System (ADS)

Kuckova, S.; Crhova, M.; Vankova, L.; Hnizda, A.; Hynek, R.; Kodicek, M.

2009-07-01

The addition of proteinaceous binders to mortars and plasters has a long tradition. The protein additions were identified in many sacral and secular historical buildings. For this method of peptide mass mapping, three model mortar samples with protein additives were prepared. These samples were analysed fresh (1-2 weeks old) and after 9 months of natural ageing. The optimal duration of tryptic cleavage (2 h) and the lowest amount of material needed for relevant analysis of fresh and weathered samples were found; the sufficient amounts of weathered and fresh mortars were set to 0.05 and 0.005 g. The list of main tryptic peptides coming from milk additives (bovine milk, curd, and whey), their relative intensities and theoretical amino acid sequences assignment is presented. Several sequences have been "de novo" confirmed by mass spectrometry.

Gaseous emissions from management of solid waste: a systematic review

PubMed Central

Pardo, Guillermo; Moral, Raúl; Aguilera, Eduardo; del Prado, Agustín

2015-01-01

The establishment of sustainable soil waste management practices implies minimizing their environmental losses associated with climate change (greenhouse gases: GHGs) and ecosystems acidification (ammonia: NH3). Although a number of management strategies for solid waste management have been investigated to quantify nitrogen (N) and carbon (C) losses in relation to varied environmental and operational conditions, their overall effect is still uncertain. In this context, we have analyzed the current scientific information through a systematic review. We quantified the response of GHG emissions, NH3 emissions, and total N losses to different solid waste management strategies (conventional solid storage, turned composting, forced aerated composting, covering, compaction, addition/substitution of bulking agents and the use of additives). Our study is based on a meta-analysis of 50 research articles involving 304 observations. Our results indicated that improving the structure of the pile (waste or manure heap) via addition or substitution of certain bulking agents significantly reduced nitrous oxide (N2O) and methane (CH4) emissions by 53% and 71%, respectively. Turned composting systems, unlike forced aerated composted systems, showed potential for reducing GHGs (N2O: 50% and CH4: 71%). Bulking agents and both composting systems involved a certain degree of pollution swapping as they significantly promoted NH3 emissions by 35%, 54%, and 121% for bulking agents, turned and forced aerated composting, respectively. Strategies based on the restriction of O2 supply, such as covering or compaction, did not show significant effects on reducing GHGs but substantially decreased NH3 emissions by 61% and 54% for covering and compaction, respectively. The use of specific additives significantly reduced NH3 losses by 69%. Our meta-analysis suggested that there is enough evidence to refine future Intergovernmental Panel on Climate Change (IPCC) methodologies from solid waste, especially for solid waste composting practices. More holistic and integrated approaches are therefore required to develop more sustainable solid waste management systems. PMID:25393229

Gaseous emissions from management of solid waste: a systematic review.

PubMed

Pardo, Guillermo; Moral, Raúl; Aguilera, Eduardo; Del Prado, Agustín

2015-03-01

The establishment of sustainable soil waste management practices implies minimizing their environmental losses associated with climate change (greenhouse gases: GHGs) and ecosystems acidification (ammonia: NH3 ). Although a number of management strategies for solid waste management have been investigated to quantify nitrogen (N) and carbon (C) losses in relation to varied environmental and operational conditions, their overall effect is still uncertain. In this context, we have analyzed the current scientific information through a systematic review. We quantified the response of GHG emissions, NH3 emissions, and total N losses to different solid waste management strategies (conventional solid storage, turned composting, forced aerated composting, covering, compaction, addition/substitution of bulking agents and the use of additives). Our study is based on a meta-analysis of 50 research articles involving 304 observations. Our results indicated that improving the structure of the pile (waste or manure heap) via addition or substitution of certain bulking agents significantly reduced nitrous oxide (N2 O) and methane (CH4 ) emissions by 53% and 71%, respectively. Turned composting systems, unlike forced aerated composted systems, showed potential for reducing GHGs (N2 O: 50% and CH4 : 71%). Bulking agents and both composting systems involved a certain degree of pollution swapping as they significantly promoted NH3 emissions by 35%, 54%, and 121% for bulking agents, turned and forced aerated composting, respectively. Strategies based on the restriction of O2 supply, such as covering or compaction, did not show significant effects on reducing GHGs but substantially decreased NH3 emissions by 61% and 54% for covering and compaction, respectively. The use of specific additives significantly reduced NH3 losses by 69%. Our meta-analysis suggested that there is enough evidence to refine future Intergovernmental Panel on Climate Change (IPCC) methodologies from solid waste, especially for solid waste composting practices. More holistic and integrated approaches are therefore required to develop more sustainable solid waste management systems. © 2014 The Authors. Global Change Biology Published by John Wiley & Sons Ltd.

Process for coal liquefaction using electrodeposited catalyst

DOEpatents

Moore, Raymond H.

1978-01-01

A process for the liquefaction of solid hydrocarbonaceous materials is disclosed. Particles of such materials are electroplated with a metal catalyst and are then suspended in a hydrocarbon oil and subjected to hydrogenolysis to liquefy the solid hydrocarbonaceous material. A liquid product oil is separated from residue solid material containing char and the catalyst metal. The catalyst is recovered from the solid material by electrolysis for reuse. A portion of the product oil can be employed as the hydrocarbon oil for suspending additional particles of catalyst coated solid carbonaceous material for hydrogenolysis.

Use of historical information in extreme surge frequency estimation: case of the marine flooding on the La Rochelle site in France

NASA Astrophysics Data System (ADS)

Hamdi, Y.; Bardet, L.; Duluc, C.-M.; Rebour, V.

2014-09-01

Nuclear power plants located in the French Atlantic coast are designed to be protected against extreme environmental conditions. The French authorities remain cautious by adopting a strict policy of nuclear plants flood prevention. Although coastal nuclear facilities in France are designed to very low probabilities of failure (e.g. 1000 year surge), exceptional surges (outliers induced by exceptional climatic events) had shown that the extreme sea levels estimated with the current statistical approaches could be underestimated. The estimation of extreme surges then requires the use of a statistical analysis approach having a more solid theoretical motivation. This paper deals with extreme surge frequency estimation using historical information (HI) about events occurred before the systematic record period. It also contributes to addressing the problem of the presence of outliers in data sets. The frequency models presented in the present paper have been quite successful in the field of hydrometeorology and river flooding but they have not been applied to sea levels data sets to prevent marine flooding. In this work, we suggest two methods of incorporating the HI: the Peaks-Over-Threshold method with HI (POTH) and the Block Maxima method with HI (BMH). Two kinds of historical data can be used in the POTH method: classical Historical Maxima (HMax) data, and Over a Threshold Supplementary (OTS) data. In both cases, the data are structured in historical periods and can be used only as complement to the main systematic data. On the other hand, in the BMH method, the basic hypothesis in statistical modeling of HI is that at least one threshold of perception exists for the whole period (historical and systematic) and that during a giving historical period preceding the period of tide gauging, only information about surges above this threshold have been recorded or archived. The two frequency models were applied to a case study from France, at the La Rochelle site where the storm Xynthia induced an outlier, to illustrate their potentials, to compare their performances and especially to analyze the impact of the use of HI on the extreme surge frequency estimation.

Use of historical information in extreme-surge frequency estimation: the case of marine flooding on the La Rochelle site in France

NASA Astrophysics Data System (ADS)

Hamdi, Y.; Bardet, L.; Duluc, C.-M.; Rebour, V.

2015-07-01

Nuclear power plants located in the French Atlantic coast are designed to be protected against extreme environmental conditions. The French authorities remain cautious by adopting a strict policy of nuclear-plants flood prevention. Although coastal nuclear facilities in France are designed to very low probabilities of failure (e.g., 1000-year surge), exceptional surges (outliers induced by exceptional climatic events) have shown that the extreme sea levels estimated with the current statistical approaches could be underestimated. The estimation of extreme surges then requires the use of a statistical analysis approach having a more solid theoretical motivation. This paper deals with extreme-surge frequency estimation using historical information (HI) about events occurred before the systematic record period. It also contributes to addressing the problem of the presence of outliers in data sets. The frequency models presented in the present paper have been quite successful in the field of hydrometeorology and river flooding but they have not been applied to sea level data sets to prevent marine flooding. In this work, we suggest two methods of incorporating the HI: the peaks-over-threshold method with HI (POTH) and the block maxima method with HI (BMH). Two kinds of historical data can be used in the POTH method: classical historical maxima (HMax) data, and over-a-threshold supplementary (OTS) data. In both cases, the data are structured in historical periods and can be used only as complement to the main systematic data. On the other hand, in the BMH method, the basic hypothesis in statistical modeling of HI is that at least one threshold of perception exists for the whole period (historical and systematic) and that during a giving historical period preceding the period of tide gauging, only information about surges above this threshold have been recorded or archived. The two frequency models were applied to a case study from France, at the La Rochelle site where the storm Xynthia induced an outlier, to illustrate their potentials, to compare their performances and especially to analyze the impact of the use of HI on the extreme-surge frequency estimation.

Teaching Geography and History through GIS: Application on Greek cultural sites

NASA Astrophysics Data System (ADS)

Skentos, Athanasios; Pavlopoulos, Kosmas; Galani, Apostolia; Theodorakopoulou, Katerina; Kritikos, Giorgos

2013-04-01

This study deals with the presentation of cultural succession in Greek space-time through a GIS application, associated with core concepts of geographic and historical education. Through the specific application students will be able to develop five distinct skills: sense of time-scale, historical and geographic comprehension, spatial analysis and interpretation, ability to perform geo-historical research, and procedure of geo-historical decision-making. The methodology is based on the calibration of a set of criteria for each cultural site that covers the topics of economy, geomorphology, society, religion, art and science. Further analysis of these data forms a geodatabase. In addition, palaeogeographic and historical maps of the cultural sites derived by the geodatabase provide information about temporal and spatial changes. As result, students will be able to develop a multidimensional and interdisciplinary approach, in order to reconstruct the evolution of the site.

Ultrasonic detection of solid phase mass flow ratio of pneumatic conveying fly ash

NASA Astrophysics Data System (ADS)

Duan, Guang Bin; Pan, Hong Li; Wang, Yong; Liu, Zong Ming

2014-04-01

In this paper, ultrasonic attenuation detection and weight balance are adopted to evaluate the solid mass ratio in this paper. Fly ash is transported on the up extraction fluidization pneumatic conveying workbench. In the ultrasonic test. McClements model and Bouguer-Lambert-Beer law model were applied to formulate the ultrasonic attenuation properties of gas-solid flow, which can give the solid mass ratio. While in the method of weigh balance, the averaged mass addition per second can reveal the solids mass flow ratio. By contrast these two solid phase mass ratio detection methods, we can know, the relative error is less.

36 CFR 1275.42 - Processing period; notice of proposed opening.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HISTORICAL MATERIALS OF THE NIXON ADMINISTRATION Access by the Public § 1275.42 Processing period; notice of... Settlement Agreement. In addition, NARA will identify and return any additional private or personal segments...

Optimization of the β-Elimination/Michael Addition Chemistry on Reversed-Phase Supports for Mass Spectrometry Analysis of O-Linked Protein Modifications

PubMed Central

Nika, Heinz; Nieves, Edward; Hawke, David H.; Angeletti, Ruth Hogue

2013-01-01

We previously adapted the β-elimination/Michael addition chemistry to solid-phase derivatization on reversed-phase supports, and demonstrated the utility of this reaction format to prepare phosphoseryl peptides in unfractionated protein digests for mass spectrometric identification and facile phosphorylation-site determination. Here, we have expanded the use of this technique to β-N-acetylglucosamine peptides, modified at serine/threonine, phosphothreonyl peptides, and phosphoseryl/phosphothreonyl peptides, followed in sequence by proline. The consecutive β-elimination with Michael addition was adapted to optimize the solid-phase reaction conditions for throughput and completeness of derivatization. The analyte remained intact during derivatization and was recovered efficiently from the silica-based, reversed-phase support with minimal sample loss. The general use of the solid-phase approach for enzymatic dephosphorylation was demonstrated with phosphoseryl and phosphothreonyl peptides and was used as an orthogonal method to confirm the identity of phosphopeptides in proteolytic mixtures. The solid-phase approach proved highly suitable to prepare substrates from low-level amounts of protein digests for phosphorylation-site determination by chemical-targeted proteolysis. The solid-phase protocol provides for a simple, robust, and efficient tool to prepare samples for phosphopeptide identification in MALDI mass maps of unfractionated protein digests, using standard equipment available in most biological laboratories. The use of a solid-phase analytical platform is expected to be readily expanded to prepare digest from O-glycosylated- and O-sulfonated proteins for mass spectrometry-based structural characterization. PMID:23997661

Reading and Writing from Multiple Source Documents in History: Effects of Strategy Instruction with Low to Average High School Writers

ERIC Educational Resources Information Center

De La Paz, Susan; Felton, Mark K.

2010-01-01

This study examined the effects of historical reasoning strategy instruction on 11th-grade students. Students learned historical inquiry strategies using 20th Century American history topics ranging from the Spanish-American war to the Gulf of Tonkin incident. In addition, students learned a pre-writing strategy for composing argumentative essays…

The Evolution of Special Education in Iowa: As Told through the Voices of Those Who Created It

ERIC Educational Resources Information Center

Grimes, Jeff; Stumme, Jim

2016-01-01

The purpose of this document is to provide a historical perspective of the evolution of special education in Iowa through the voices of the people who created the system of support for individuals with disabilities. In addition to the interviews, extensive historical literature reviews were conducted. One hundred and thirty individuals were…

Understanding "The Catcher in the Rye": A Student Casebook to Issues, Sources, and Historical Documents.

ERIC Educational Resources Information Center

Pinsker, Sanford; Pinsker, Ann

The social, cultural, and historical documents and commentary in this casebook illuminate the reading of "The Catcher in the Rye," a novel that has become an important rite of passage for many young adults. In addition to a literary analysis, the casebook acquaints students with the larger world in which Holden Caulfield, the…

Final expanded site inspection, ammunition storage area, Anniston Army Depot, Anniston, Alabama. Final report, September 1992-November 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suomela, K.D.; Highsmith, R.L.; Rapuano, K.F.

1994-11-15

An Expanded Site Inspection (ESI) was conducted at the Anniston Army Depot (ANAD) Ammunition Storage Area (ASA). The objective of this ESI was to gather the information and data necessary to determine whether there is sufficient evidence of any release of contamination that would require additional investigation. The ASA contains 1,300 ammunition storage magazines and an ammunition maintenance workshop complex which includes buildings for maintenance, demilitarization, and inspection of all types of ammunition and their components. Fifteen Solid Waste Management Units (SWMUs) were the focus of the ESI, of which 11 were recommend for further investigation. The work included amore » review of historical records, field investigations, laboratory analyses, data interpretation, and report preparation. Contamination from volatile organic compounds and semi volatile organic compounds is not a major problem at the ASA. Arsenic, beryllium, cadmium, chromium, lead, mercury, nickel, silver, vanadium, zinc, explosives, and total petroleum hydrocarbons were detected above control screening values levels in one or more of the media sampled. Nitrate/nitrite and total organic carbon were also detected above control screening values in samples of groundwater, soil, and sediment from a number of SWMUs.« less

Assessment of the Evolution of Cancer Treatment Therapies

PubMed Central

Arruebo, Manuel; Vilaboa, Nuria; Sáez-Gutierrez, Berta; Lambea, Julio; Tres, Alejandro; Valladares, Mónica; González-Fernández, África

2011-01-01

Cancer therapy has been characterized throughout history by ups and downs, not only due to the ineffectiveness of treatments and side effects, but also by hope and the reality of complete remission and cure in many cases. Within the therapeutic arsenal, alongside surgery in the case of solid tumors, are the antitumor drugs and radiation that have been the treatment of choice in some instances. In recent years, immunotherapy has become an important therapeutic alternative, and is now the first choice in many cases. Nanotechnology has recently arrived on the scene, offering nanostructures as new therapeutic alternatives for controlled drug delivery, for combining imaging and treatment, applying hyperthermia, and providing directed target therapy, among others. These therapies can be applied either alone or in combination with other components (antibodies, peptides, folic acid, etc.). In addition, gene therapy is also offering promising new methods for treatment. Here, we present a review of the evolution of cancer treatments, starting with chemotherapy, surgery, radiation and immunotherapy, and moving on to the most promising cutting-edge therapies (gene therapy and nanomedicine). We offer an historical point of view that covers the arrival of these therapies to clinical practice and the market, and the promises and challenges they present. PMID:24212956

Evaluation of passive transfer in captive greater kudu (Tragelaphus strepsiceros).

PubMed

Hammond, Elizabeth E; Fiorello, Christine V

2011-12-01

Failure of passive transfer (FPT) in captive greater kudu (Tragelaphus strepsiceros) calves can lead to increased morbidity and mortality. In this retrospective study, serum samples from neonatal kudu calves were tested for immunoglobulin using different tests validated for domestic ruminants, including measurement of gamma globulin (GG) measured by protein electrophoresis, total solids (TS) measured by calibrated refractometry, total protein (TP) and globulins measured by colorimetry, gamma glutamyltransferase (GGT), and the zinc sulfate turbidity test (ZSTT). In a logistic regression model, TP, TS, globulins, and the natural log transform of GGT were the only significant parameters associated with FPT. Various historic parameters related to the dam, as well as calf weight, sex, glucose, and packed cell volume, were not significant. Based on the results, FPT in greater kudu is defined as GG of < 0.5 g/dl, a value lower than that in domestic cattle. TS measured by refractometry has an 80% sensitivity and a 100% specificity for FPT in greater kudu. With FPT defined as GG < 0.5 g/dl, kudu calves with a TS < 4.8 g/dl and a negative ZSTT have an increased probability of requiring medical intervention and additional diagnostics may be warranted.

Hydration mechanisms of two polymorphs of synthetic ye'elimite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cuesta, A.; Álvarez-Pinazo, G.; Sanfélix, S.G.

2014-09-15

Ye'elimite is the main phase in calcium sulfoaluminate cements and also a key phase in sulfobelite cements. However, its hydration mechanism is not well understood. Here we reported new data on the hydration behavior of ye'elimite using synchrotron and laboratory powder diffraction coupled to the Rietveld methodology. Both internal and external standard methodologies have been used to determine the overall amorphous contents. We have addressed the standard variables: water-to-ye'elimite ratio and additional sulfate sources of different solubilities. Moreover, we report a deep study of the role of the polymorphism of pure ye'elimites. The hydration behavior of orthorhombic stoichiometric and pseudo-cubicmore » solid-solution ye'elimites is discussed. In the absence of additional sulfate sources, stoichiometric-ye'elimite reacts slower than solid-solution-ye'elimite, and AFm-type phases are the main hydrated crystalline phases, as expected. Moreover, solid-solution-ye'elimite produces higher amounts of ettringite than stoichiometric-ye'elimite. However, in the presence of additional sulfates, stoichiometric-ye'elimite reacts faster than solid-solution-ye'elimite.« less

Physical environment and hydrologic characteristics of coal-mining areas in Missouri

USGS Publications Warehouse

Vaill, J.E.; Barks, James H.

1980-01-01

Hydrologic information for the north-central and western coal-mining regions of Missouri is needed to define the hydrologic system in these areas of major historic and planned coal development. This report describes the physical setting, climate, coal-mining practices, general hydrologic system, and the current (1980) hydrologie data base in these two coal-mining regions. Streamflow in both mining regions is poorly sustained. Stream water quality generally varies with location and the magnitude of coal-mining activity in a watershed. Streams in non coal-mining areas generally have dissolved-solids concentrations less than 400 milligrams per liter. Acid-mine drainage has seriously affected some streams by reducing the pH to less than 4.0 and increasing the dissolved-solids concentrations to greater than 1,000 milligrams per liter. This has resulted in fish kills in some instances. Ground-water movement is impeded both laterally and vertically in both mining regions, especially in western Missouri, because of the low hydraulic conductivity of the rocks of Pennsylvanian age. The quality of ground water varies widely depending on location and depth. Ground water commonly contains high concentrations of iron and sulfate, and dissolved-solids concentrations generally are greater than 1,000 milligrams per liter.

Quantum entanglement at ambient conditions in a macroscopic solid-state spin ensemble

PubMed Central

Klimov, Paul V.; Falk, Abram L.; Christle, David J.; Dobrovitski, Viatcheslav V.; Awschalom, David D.

2015-01-01

Entanglement is a key resource for quantum computers, quantum-communication networks, and high-precision sensors. Macroscopic spin ensembles have been historically important in the development of quantum algorithms for these prospective technologies and remain strong candidates for implementing them today. This strength derives from their long-lived quantum coherence, strong signal, and ability to couple collectively to external degrees of freedom. Nonetheless, preparing ensembles of genuinely entangled spin states has required high magnetic fields and cryogenic temperatures or photochemical reactions. We demonstrate that entanglement can be realized in solid-state spin ensembles at ambient conditions. We use hybrid registers comprising of electron-nuclear spin pairs that are localized at color-center defects in a commercial SiC wafer. We optically initialize 103 identical registers in a 40-μm3 volume (with 0.95−0.07+0.05 fidelity) and deterministically prepare them into the maximally entangled Bell states (with 0.88 ± 0.07 fidelity). To verify entanglement, we develop a register-specific quantum-state tomography protocol. The entanglement of a macroscopic solid-state spin ensemble at ambient conditions represents an important step toward practical quantum technology. PMID:26702444

Lasers, their development, and applications at M.I.T. Lincoln Laboratory

NASA Technical Reports Server (NTRS)

Rediker, R. H.; Melngailis, I.; Mooradian, A.

1984-01-01

A historical account of the work on lasers at MIT Lincoln Laboratory is presented. Highlighted are the efforts that led to the coinvention of the semiconductor laser and the Laboratory's later role in establishing the feasibility of GaInAsP/InP semiconductor lasers for use in fiber telecommunications at 1.3-1.5 micron wavelengths. Descriptions of other important developments include tunable lead-salt semiconductor and solid-state lasers for spectroscopy and LIDAR applications, respectively, as well as ultrastable CO2 lasers for coherent infrared radar.

RCRA Facility Investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 3. Appendixes 1 through 8

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1991-09-01

This report presents compiled information concerning a facility investigation of waste area group 6(WAG-6), of the solid waste management units (SWMU'S) at Oak Ridge National Laboratory (ORNL). The WAG is a shallow ground disposal area for low-level radioactive wastes and chemical wastes. The report contains information on hydrogeological data, contaminant characterization, radionuclide concentrations, risk assessment from doses to humans and animals and associated cancer risks, exposure via food chains, and historical data. (CBS)

Books and monographs on finite element technology

NASA Technical Reports Server (NTRS)

Noor, A. K.

1985-01-01

The present paper proviees a listing of all of the English books and some of the foreign books on finite element technology, taking into account also a list of the conference proceedings devoted solely to finite elements. The references are divided into categories. Attention is given to fundamentals, mathematical foundations, structural and solid mechanics applications, fluid mechanics applications, other applied science and engineering applications, computer implementation and software systems, computational and modeling aspects, special topics, boundary element methods, proceedings of symmposia and conferences on finite element technology, bibliographies, handbooks, and historical accounts.

Trends in solid state electronics, part 2

NASA Technical Reports Server (NTRS)

Gassaway, J. D.

1972-01-01

Developments in the fields of semiconductors and magnetics are surveyed. Materials, devices, theory, and fabrication technology are discussed. Important events up until the present time are reported, and events are interpreted through historical perspective. A brief analysis of forces which have driven the development of today's electronic technology and some projections of present trends are given. More detailed discussions are presented for four areas of contemporary interest: amorphous semiconductors, bubble domain devices, charge-coupled devices, and electron and ion beam techniques. Beam addressed magnetic memories are reviewed to a lesser extent.

An evaluation of methods for estimating decadal stream loads

NASA Astrophysics Data System (ADS)

Lee, Casey J.; Hirsch, Robert M.; Schwarz, Gregory E.; Holtschlag, David J.; Preston, Stephen D.; Crawford, Charles G.; Vecchia, Aldo V.

2016-11-01

Effective management of water resources requires accurate information on the mass, or load of water-quality constituents transported from upstream watersheds to downstream receiving waters. Despite this need, no single method has been shown to consistently provide accurate load estimates among different water-quality constituents, sampling sites, and sampling regimes. We evaluate the accuracy of several load estimation methods across a broad range of sampling and environmental conditions. This analysis uses random sub-samples drawn from temporally-dense data sets of total nitrogen, total phosphorus, nitrate, and suspended-sediment concentration, and includes measurements of specific conductance which was used as a surrogate for dissolved solids concentration. Methods considered include linear interpolation and ratio estimators, regression-based methods historically employed by the U.S. Geological Survey, and newer flexible techniques including Weighted Regressions on Time, Season, and Discharge (WRTDS) and a generalized non-linear additive model. No single method is identified to have the greatest accuracy across all constituents, sites, and sampling scenarios. Most methods provide accurate estimates of specific conductance (used as a surrogate for total dissolved solids or specific major ions) and total nitrogen - lower accuracy is observed for the estimation of nitrate, total phosphorus and suspended sediment loads. Methods that allow for flexibility in the relation between concentration and flow conditions, specifically Beale's ratio estimator and WRTDS, exhibit greater estimation accuracy and lower bias. Evaluation of methods across simulated sampling scenarios indicate that (1) high-flow sampling is necessary to produce accurate load estimates, (2) extrapolation of sample data through time or across more extreme flow conditions reduces load estimate accuracy, and (3) WRTDS and methods that use a Kalman filter or smoothing to correct for departures between individual modeled and observed values benefit most from more frequent water-quality sampling.

An evaluation of methods for estimating decadal stream loads

USGS Publications Warehouse

Lee, Casey; Hirsch, Robert M.; Schwarz, Gregory E.; Holtschlag, David J.; Preston, Stephen D.; Crawford, Charles G.; Vecchia, Aldo V.

2016-01-01

Effective management of water resources requires accurate information on the mass, or load of water-quality constituents transported from upstream watersheds to downstream receiving waters. Despite this need, no single method has been shown to consistently provide accurate load estimates among different water-quality constituents, sampling sites, and sampling regimes. We evaluate the accuracy of several load estimation methods across a broad range of sampling and environmental conditions. This analysis uses random sub-samples drawn from temporally-dense data sets of total nitrogen, total phosphorus, nitrate, and suspended-sediment concentration, and includes measurements of specific conductance which was used as a surrogate for dissolved solids concentration. Methods considered include linear interpolation and ratio estimators, regression-based methods historically employed by the U.S. Geological Survey, and newer flexible techniques including Weighted Regressions on Time, Season, and Discharge (WRTDS) and a generalized non-linear additive model. No single method is identified to have the greatest accuracy across all constituents, sites, and sampling scenarios. Most methods provide accurate estimates of specific conductance (used as a surrogate for total dissolved solids or specific major ions) and total nitrogen – lower accuracy is observed for the estimation of nitrate, total phosphorus and suspended sediment loads. Methods that allow for flexibility in the relation between concentration and flow conditions, specifically Beale’s ratio estimator and WRTDS, exhibit greater estimation accuracy and lower bias. Evaluation of methods across simulated sampling scenarios indicate that (1) high-flow sampling is necessary to produce accurate load estimates, (2) extrapolation of sample data through time or across more extreme flow conditions reduces load estimate accuracy, and (3) WRTDS and methods that use a Kalman filter or smoothing to correct for departures between individual modeled and observed values benefit most from more frequent water-quality sampling.

Case study II: application of the divalent cation bridging theory to improve biofloc properties and industrial activated sludge system performance-using alternatives to sodium-based chemicals.

PubMed

Higgins, Matthew J; Sobeck, David C; Owens, Steven J; Szabo, Lynn M

2004-01-01

The objective of this study was to investigate the application of the divalent cation bridging theory (DCBT) as a tool in the chemical selection process at an activated sludge plant to improve settling, dewatering, and effluent quality. According to the DCBT, to achieve improvements, the goal of chemical selection should be to reduce the ratio of monovalent-to-divalent (M/D) cations. A study was conducted to determine the effect of using magnesium hydroxide [Mg(OH)2] as an alternative to sodium hydroxide (NaOH) at a full-scale industrial wastewater treatment plant. Floc properties and treatment plant performance were measured for approximately one year during two periods of NaOH addition and Mg(OH)2 addition. A cost analysis of plant operation during NaOH and Mg(OH)2 use was also performed. During NaOH addition, the M/D ratio was 48, while, during Mg(OH)2 addition, this ratio was reduced to an average of approximately 0.1. During the Mg(OH)2 addition period, the sludge volume index, effluent total suspended solids, and effluent chemical oxygen demand were reduced by approximately 63, 31, and 50%, respectively, compared to the NaOH addition period. The alum and polymer dose used for clarification was reduced by approximately 50 and 60%, respectively, during Mg(OH)2 addition. The dewatering properties of the activated sludge improved dewatering as measured by decreased capillary suction time and specific resistance to filtration (SRF), along with an increase in cake solids from the SRF test. This corresponded to a reduction in the volume of solids thickened by centrifuges at the treatment plant, which reduced the disposal costs of solids. Considering the costs for chemicals and solids disposal, the annual cost of using Mg(OH)2 was approximately 30,000 dollars to 115,000 dollars less than using NaOH, depending on the pricing of NaOH. The results of this study confirm that the DCBT is a useful tool for assessing chemical-addition strategies and their potential effect on activated sludge performance.

'Wasteaware' benchmark indicators for integrated sustainable waste management in cities.

PubMed

Wilson, David C; Rodic, Ljiljana; Cowing, Michael J; Velis, Costas A; Whiteman, Andrew D; Scheinberg, Anne; Vilches, Recaredo; Masterson, Darragh; Stretz, Joachim; Oelz, Barbara

2015-01-01

This paper addresses a major problem in international solid waste management, which is twofold: a lack of data, and a lack of consistent data to allow comparison between cities. The paper presents an indicator set for integrated sustainable waste management (ISWM) in cities both North and South, to allow benchmarking of a city's performance, comparing cities and monitoring developments over time. It builds on pioneering work for UN-Habitat's solid waste management in the World's cities. The comprehensive analytical framework of a city's solid waste management system is divided into two overlapping 'triangles' - one comprising the three physical components, i.e. collection, recycling, and disposal, and the other comprising three governance aspects, i.e. inclusivity; financial sustainability; and sound institutions and proactive policies. The indicator set includes essential quantitative indicators as well as qualitative composite indicators. This updated and revised 'Wasteaware' set of ISWM benchmark indicators is the cumulative result of testing various prototypes in more than 50 cities around the world. This experience confirms the utility of indicators in allowing comprehensive performance measurement and comparison of both 'hard' physical components and 'soft' governance aspects; and in prioritising 'next steps' in developing a city's solid waste management system, by identifying both local strengths that can be built on and weak points to be addressed. The Wasteaware ISWM indicators are applicable to a broad range of cities with very different levels of income and solid waste management practices. Their wide application as a standard methodology will help to fill the historical data gap. Copyright © 2014 Elsevier Ltd. All rights reserved.

Combustion Performance of a Staged Hybrid Rocket with Boron addition

NASA Astrophysics Data System (ADS)

Lee, D.; Lee, C.

2018-04-01

In this paper, the effect of boron on overall system specific impulse was investigated. Additionally, a series of combustion tests was carried out to analyze and evaluate the effect of boron addition on O/F variation and radial temperature profiles. To maintain the hybrid rocket engine advantages, upper limit of boron contents in solid fuel was set to be 10 wt%. The results also suggested that, when adding boron to solid fuel, it helped to provide more uniform radial temperature distribution and also to increase specific impulse by 3.2%.

Interfacial phonon scattering and transmission loss in > 1 µm thick silicon-on-insulator thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Puqing; Lindsay, Lucas R.; Huang, Xi

Scattering of phonons at boundaries of a crystal (grains, surfaces, or solid/solid interfaces) is characterized by the phonon wavelength, the angle of incidence, and the interface roughness, as historically evaluated using a specularity parameter p formulated by Ziman [Electrons and Phonons (Clarendon Press, Oxford, 1960)]. This parameter was initially defined to determine the probability of a phonon specularly reflecting or diffusely scattering from the rough surface of a material. The validity of Ziman's theory as extended to solid/solid interfaces has not been previously validated. Here, to better understand the interfacial scattering of phonons and to test the validity of Ziman'smore » theory, we precisely measured the in-plane thermal conductivity of a series of Si films in silicon-on-insulator (SOI) wafers by time-domain thermoreflectance (TDTR) for a Si film thickness range of 1–10 μm and a temperature range of 100–300 K. The Si/SiO 2 interface roughness was determined to be 0.11±0.04nm using transmission electron microscopy (TEM). Furthermore, we compared our in-plane thermal conductivity measurements to theoretical calculations that combine first-principles phonon transport with Ziman's theory. Calculations using Ziman's specularity parameter significantly overestimate values from the TDTR measurements. We attribute this discrepancy to phonon transmission through the solid/solid interface into the substrate, which is not accounted for by Ziman's theory for surfaces. The phonons that are specularly transmitted into an amorphous layer will be sufficiently randomized by the time they come back to the crystalline Si layer, the effect of which is practically equivalent to a diffuse reflection at the interface. Finally, we derive a simple expression for the specularity parameter at solid/amorphous interfaces and achieve good agreement between calculations and measurement values.« less

Interfacial phonon scattering and transmission loss in > 1 µm thick silicon-on-insulator thin films

DOE PAGES

Jiang, Puqing; Lindsay, Lucas R.; Huang, Xi; ...

2018-05-17

Scattering of phonons at boundaries of a crystal (grains, surfaces, or solid/solid interfaces) is characterized by the phonon wavelength, the angle of incidence, and the interface roughness, as historically evaluated using a specularity parameter p formulated by Ziman [Electrons and Phonons (Clarendon Press, Oxford, 1960)]. This parameter was initially defined to determine the probability of a phonon specularly reflecting or diffusely scattering from the rough surface of a material. The validity of Ziman's theory as extended to solid/solid interfaces has not been previously validated. Here, to better understand the interfacial scattering of phonons and to test the validity of Ziman'smore » theory, we precisely measured the in-plane thermal conductivity of a series of Si films in silicon-on-insulator (SOI) wafers by time-domain thermoreflectance (TDTR) for a Si film thickness range of 1–10 μm and a temperature range of 100–300 K. The Si/SiO 2 interface roughness was determined to be 0.11±0.04nm using transmission electron microscopy (TEM). Furthermore, we compared our in-plane thermal conductivity measurements to theoretical calculations that combine first-principles phonon transport with Ziman's theory. Calculations using Ziman's specularity parameter significantly overestimate values from the TDTR measurements. We attribute this discrepancy to phonon transmission through the solid/solid interface into the substrate, which is not accounted for by Ziman's theory for surfaces. The phonons that are specularly transmitted into an amorphous layer will be sufficiently randomized by the time they come back to the crystalline Si layer, the effect of which is practically equivalent to a diffuse reflection at the interface. Finally, we derive a simple expression for the specularity parameter at solid/amorphous interfaces and achieve good agreement between calculations and measurement values.« less

Enzymatic Pretreatment Coupled with the Addition of p-Hydroxyanisole Increased Levulinic Acid Production from Steam-Exploded Rice Straw Short Fiber.

PubMed

Ma, Li-Tong; Zhao, Zhi-Min; Yu, Bin; Chen, Hong-Zhang

2016-11-01

Levulinic acid production, directly from lignocellulosic biomass, resulted in low yields due to the poor substrate accessibility and occurrence of side reactions. The effects of reaction conditions, enzymatic pretreatment, and inhibitor addition on the conversion of steam-exploded rice straw (SERS) short fiber to levulinic acid catalyzed by solid superacid were investigated systematically. The results indicated that the optimal reaction conditions were temperature, time, and solid superacid concentration combinations of 200 °C, 15 min, and 7.5 %. Enzymatic pretreatment improved the substrate accessibility to solid superacid catalyst, and p-hydroxyanisole inhibitor reduced the side reactions during reaction processes, which helped to increase levulinic acid yield. The levulinic acid yield reached 25.2 % under the optimal conditions, which was 61.5 % higher than that without enzymatic pretreatment and inhibitor addition. Therefore, enzymatic pretreatment coupled with the addition of p-hydroxyanisole increased levulinic acid production effectively, which contributed to the value-added utilization of lignocellulosic biomass.

Effects of fermentation substrate conditions on corn-soy co-fermentation for fuel ethanol production.

PubMed

Yao, Linxing; Lee, Show-Ling; Wang, Tong; de Moura, Juliana M L N; Johnson, Lawrence A

2012-09-01

Soy skim, a protein-rich liquid co-product from the aqueous extraction of soybeans, was co-fermented with corn to produce ethanol. Effects of soy skim addition level, type of skim, corn particle size, water-to-solids ratio, and urea on co-fermentation were determined. The addition of 20-100% skim increased the fermentation rate by 18-27% and shortened the fermentation time by 5-7h without affecting ethanol yield. Finely ground corn or high water-to-solids ratio (≥ 3.0) in the mash gave higher fermentation rates, but did not increase the ethanol yield. When the water was completely replaced with soy skim, the addition of urea became unnecessary. Soy skim retentate that was concentrated by nanofiltration increased fermentation rate by 25%. The highest level of skim addition resulted in a finished beer with 16% solids, 47% protein (dwb) containing 3.6% lysine, and an ethanol yield of 39 g/100g dry corn. Copyright © 2012 Elsevier Ltd. All rights reserved.

2. Southeast side of addition. View to northwest. Offutt ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Southeast side of addition. View to northwest. - Offutt Air Force Base, Looking Glass Airborne Command Post, Aerospace Ground Equipment (AGE) Storage Facility, Far Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

Fabrication, testing and simulation of all solid state three dimensional Li-ion batteries

DOE PAGES

Talin, Albert Alec; Ruzmetov, Dmitry; Kolmakov, Andrei; ...

2016-11-10

Realization of safe, long cycle life and simple to package solid-state rechargeable batteries with high energy and power density has been a long-standing goal of the energy storage community. [1,2] Much of the research activity has been focused on developing new solid electrolytes with high Li ionic conductivity. In addition, LiPON, the only solid electrolyte currently used in commercial thin film solid state Li-ion batteris (SSLIBs), has a conductivity of ~10 -6 S/cm, compared to ~0.01 S/cm typically observed for liquid organic electrolytes [3].

The effects of different flooring types on the behavior, health, and welfare of finishing beef steers.

PubMed

Elmore, M R P; Elischer, M F; Claeys, M C; Pajor, E A

2015-03-01

Raising beef cattle on concrete floors can negatively impact their welfare by increasing joint swelling and body lesions, as well as abnormalities in resting behavior and postural changes. We hypothesized that the addition of rubber mats to concrete pens would improve beef cattle welfare by improving performance, health, hygiene, and resting behavior. Forty-eight crossbred Angus steers were housed in pens of 4 and randomly assigned to a single flooring treatment: (1) fully slatted concrete (CON), (2) fully slatted rubber mat (SLAT), or (3) solid rubber mat (SOLID; 60% of pen floor) from 36 to 48 wk of age. Weight, ADG, lesions, gait score, joint swelling, and animal and pen cleanliness were collected every 2 wk. Behavioral time budgets and frequency of postural changes (an indicator of floor traction and comfort) were collected at 0, 6, and 12 wk. No differences in weight gain or ADG were observed. Steers on SOLID flooring (0.80 ± 0.08) showed increased lesions compared to SLAT (0.38 ± 0.08) and CON (0.37 ± 0.08; both, = 0.05); however, there was no difference between SLAT and CON. SLAT steers (1.69 ± 0.04) showed a reduced gait score compared to SOLID (1.95 ± 0.04) and CON (1.98 ± 0.04; both, < 0.05), but SOLID and CON did not differ. Steers on SLAT flooring had less joint swelling (both knees and hocks) compared to SOLID and CON (all comparisons, < 0.05), but SOLID and CON did not differ. Steers on SOLID (3.64 ± 0.05) flooring were dirtier than those on SLAT (2.27 ± 0.05) and CON (2.19 ± 0.05; both, < 0.001), whereas SLAT and CON were similar. Additionally, SOLID and SLAT pens were less clean than CON pens ( < 0.001 and = 0.094, respectively), and SOLID was less clean than SLAT ( < 0.001). Time budget behavior was affected by treatment ( = 0.043), where SOLID differed from CON and SLAT (both, < 0.05). Steers on SOLID flooring preferred to rest on the rubber mat vs. slatted concrete ( = 0.001). Steers on SLAT flooring changed their posture more frequently than those on SOLID and CON flooring (both, < 0.05), but SOLID and CON did not differ. Compared to CON steers, SOLID steers showed an increase in lesions and a reduction in cleanliness, whereas SLAT steers showed a decrease in gait score and joint swelling and an increase in postural changes. Combined, these data suggest that the addition of slatted rubber mats to concrete pens may improve beef cattle welfare.

A contribution to the knowledge of HMX decomposition and application of results. [at atmospheric pressure

NASA Technical Reports Server (NTRS)

Kraeutle, K. J.

1980-01-01

The decomposition of cyclotramethylenetetranitramine (HMX) in the solid and liquid phase was studied by isothermal and nonisothermal heating at atmospheric pressure. Decomposition rates of solid HMX changed with sample size and gaseous environment. Kinetic parameters were obtained from weight loss measurements in the temperature range 229 C - 269 C. These tests also yielded highly porous solid residues. Qualitative aspects of solid and liquid phase decomposition of HMX with additives were also investigated in isothermal and nonisothermal tests.

'All-solid-state' electrochemistry of a protein-confined polymer electrolyte film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parthasarathy, Meera; Pillai, Vijayamohanan K.; Mulla, Imtiaz S.

2007-12-07

Interfacial redox behavior of a heme protein (hemoglobin) confined in a solid polymer electrolyte membrane, Nafion (a perfluoro sulfonic acid ionomer) is investigated using a unique 'all-solid-state' electrochemical methodology. The supple phase-separated structure of the polymer electrolyte membrane, with hydrophilic pools containing solvated protons and water molecules, is found to preserve the incorporated protein in its active form even in the solid-state, using UV-visible, Fluorescence (of Tryptophan and Tyrosine residues) and DRIFT (diffuse reflectance infrared Fourier transform) spectroscopy. More specifically, solid-state cyclic voltammetry and electrochemical impedance of the protein-incorporated polymer films reveal that the Fe{sup 2+}-form of the entrapped proteinmore » is found to bind molecular oxygen more strongly than the native protein. In the 'all-solid-state' methodology, as there is no need to dip the protein-modified electrode in a liquid electrolyte (like the conventional electrochemical methods), it offers an easier means to study a number of proteins in a variety of polymer matrices (even biomimetic assemblies). In addition, the results of the present investigation could find interesting application in a variety of research disciplines, in addition to its fundamental scientific interest, including protein biotechnology, pharmaceutical and biomimetic chemistry.« less

Progress and prospect on failure mechanisms of solid-state lithium batteries

NASA Astrophysics Data System (ADS)

Ma, Jun; Chen, Bingbing; Wang, Longlong; Cui, Guanglei

2018-07-01

By replacing traditional liquid organic electrolyte with solid-state electrolyte, the solid-state lithium batteries powerfully come back to the energy storage field due to their eminent safety and energy density. In recent years, a variety of solid-state lithium batteries based on excellent solid-state electrolytes are developed. However, the performance degradation of solid-state lithium batteries during cycling and storing is still a serious challenge for practical application. Therefore, this review summarizes the research progress of solid-state lithium batteries from the perspectives of failure phenomena and failure mechanisms. Additionally, the development of methodologies on studying the failure mechanisms of solid-state lithium batteries is also reviewed. Moreover, some perspectives on the remaining questions for understanding the failure behaviors and achieving long cycle life, high safety and high energy density solid-state lithium batteries are presented. This review will help researchers to recognize the status of solid-state lithium batteries objectively and attract much more research interest in conquering the failure issues of solid-state lithium batteries.

Curious parallels and curious connections--phylogenetic thinking in biology and historical linguistics.

PubMed

Atkinson, Quentin D; Gray, Russell D

2005-08-01

In The Descent of Man (1871), Darwin observed "curious parallels" between the processes of biological and linguistic evolution. These parallels mean that evolutionary biologists and historical linguists seek answers to similar questions and face similar problems. As a result, the theory and methodology of the two disciplines have evolved in remarkably similar ways. In addition to Darwin's curious parallels of process, there are a number of equally curious parallels and connections between the development of methods in biology and historical linguistics. Here we briefly review the parallels between biological and linguistic evolution and contrast the historical development of phylogenetic methods in the two disciplines. We then look at a number of recent studies that have applied phylogenetic methods to language data and outline some current problems shared by the two fields.

Simulation of municipal solid waste degradation in aerobic and anaerobic bioreactor landfills.

PubMed

Patil, Bhagwan Shamrao; C, Agnes Anto; Singh, Devendra Narain

2017-03-01

Municipal solid waste generation is huge in growing cities of developing nations such as India, owing to the rapid industrial and population growth. In addition to various methods for treatment and disposal of municipal solid waste (landfills, composting, bio-methanation, incineration and pyrolysis), aerobic/anaerobic bioreactor landfills are gaining popularity for economical and effective disposal of municipal solid waste. However, efficiency of municipal solid waste bioreactor landfills primarily depends on the municipal solid waste decomposition rate, which can be accelerated through monitoring moisture content and temperature by using the frequency domain reflectometry probe and thermocouples, respectively. The present study demonstrates that these landfill physical properties of the heterogeneous municipal solid waste mass can be monitored using these instruments, which facilitates proper scheduling of the leachate recirculation for accelerating the decomposition rate of municipal solid waste.

6. General interior overview of addition. View to northwest. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. General interior overview of addition. View to northwest. - Offutt Air Force Base, Looking Glass Airborne Command Post, Aerospace Ground Equipment (AGE) Storage Facility, Far Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

5. General interior overview of addition. View to south. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. General interior overview of addition. View to south. - Offutt Air Force Base, Looking Glass Airborne Command Post, Aerospace Ground Equipment (AGE) Storage Facility, Far Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

Understanding the Palestinian-Israeli Conflict: A Historical and Religious Perspective. Fulbright-Hays Summer Seminars Abroad Program, 2000 (Egypt and Israel).

ERIC Educational Resources Information Center

Bosso, David

In light of on-going strife in the Middle East, particularly in Palestinian-Israeli relations, it is intriguing to note how relatively unaware many Americans are of the historical and religious framework from which much of the conflict derives. In addition, the perception of many Americans of current Palestinian-Israeli relations has been tainted…

Environmental Impact Analysis Process, Groom Mountain Range, Lincoln County, Nevada

DTIC Science & Technology

1985-10-01

bases clustered around springs, temporary camps, rock shelters , quarries, lithic scatters, rock art, pinyon caches, pot drops, isolates, and historic...include pinyon caches and rock shelters with associated historic artifacts and many of the spring sites. These sites provide an unusual research...Management. (b) Proposed Action: Renewed Withdrawal of Groom Mountain Range Addition to Nellis Air Force Bombing and Gunnery Range, Lincoln County, Nevada. (c

Historic Radio Astronomy Working Group

NASA Astrophysics Data System (ADS)

2007-06-01

This special issue of Astronomische Nachrichten contains the proceedings of a session of the Historic Radio Astronomy Working Group of the International Astronomical Union that took place during the 26th General Assembly of the IAU in Prague on 17th August 2006. In addition to the talks presented in Prague some contributions were solicited to give a more complete overview of `The Early History of European Radio Astronomy'.

An Early Historical Examination of the Educational Intent of Supervised Agricultural Experiences (SAEs) and Project-Based Learning in Agricultural Education

ERIC Educational Resources Information Center

Smith, Kasee L.; Rayfield, John

2016-01-01

Project-based learning has been a component of agricultural education since its inception. In light of the current call for additional emphasis of the Supervised Agricultural Experience (SAE) component of agricultural education, there is a need to revisit the roots of project-based learning. This early historical research study was conducted to…

Restoring oak forest, woodlands and savannahs using modern silvicultural analogs to historic cultural fire regimes

Treesearch

Daniel C. Dey; Richard P. Guyette; Callie J. Schweitzer; Michael C. Stambaugh; John M. Kabrick

2015-01-01

Variability in historic fire regimes in eastern North America resulted in an array of oak savannahs, woodlands and forests that were dominant vegetation types throughout the region. In the past century, once abundant savannahs and woodlands have become scarce due to conversion to agriculture, or development of forest structure in the absence of fire. In addition, the...

Geopan AT@S: a Brokering Based Gateway to Georeferenced Historical Maps for Risk Analysis

NASA Astrophysics Data System (ADS)

Previtali, M.

2017-08-01

Importance of ancient and historical maps is nowadays recognized in many applications (e.g., urban planning, landscape valorisation and preservation, land changes identification, etc.). In the last years a great effort has been done by different institutions, such as Geographical Institutes, Public Administrations, and collaborative communities, for digitizing and publishing online collections of historical maps. In spite of this variety and availability of data, information overload makes difficult their discovery and management: without knowing the specific repository where the data are stored, it is difficult to find the information required. In addition, problems of interconnection between different data sources and their restricted interoperability may arise. This paper describe a new brokering based gateway developed to assure interoperability between data, in particular georeferenced historical maps and geographic data, gathered from different data providers, with various features and referring to different historical periods. The developed approach is exemplified by a new application named GeoPAN Atl@s that is aimed at linking in Northern Italy area land changes with risk analysis (local seismicity amplification and flooding risk) by using multi-temporal data sources and historic maps.

Improved ethanol yield and reduced Minimum Ethanol Selling Price (MESP) by modifying low severity dilute acid pretreatment with deacetylation and mechanical refining: 1) Experimental

PubMed Central

2012-01-01

Background Historically, acid pretreatment technology for the production of bio-ethanol from corn stover has required severe conditions to overcome biomass recalcitrance. However, the high usage of acid and steam at severe pretreatment conditions hinders the economic feasibility of the ethanol production from biomass. In addition, the amount of acetate and furfural produced during harsh pretreatment is in the range that strongly inhibits cell growth and impedes ethanol fermentation. The current work addresses these issues through pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. Results The results showed that deacetylation with 0.1 M NaOH before acid pretreatment improved the monomeric xylose yield in pretreatment by up to 20% while keeping the furfural yield under 2%. Deacetylation also improved the glucose yield by 10% and the xylose yield by 20% during low solids enzymatic hydrolysis. Mechanical refining using a PFI mill further improved sugar yields during both low- and high-solids enzymatic hydrolysis. Mechanical refining also allowed enzyme loadings to be reduced while maintaining high yields. Deacetylation and mechanical refining are shown to assist in achieving 90% cellulose yield in high-solids (20%) enzymatic hydrolysis. When fermentations were performed under pH control to evaluate the effect of deacetylation and mechanical refining on the ethanol yields, glucose and xylose utilizations over 90% and ethanol yields over 90% were achieved. Overall ethanol yields were calculated based on experimental results for the base case and modified cases. One modified case that integrated deacetylation, mechanical refining, and washing was estimated to produce 88 gallons of ethanol per ton of biomass. Conclusion The current work developed a novel bio-ethanol process that features pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. The new process shows improved overall ethanol yields compared to traditional dilute acid pretreatment. The experimental results from this work support the techno-economic analysis and calculation of Minimum Ethanol Selling Price (MESP) detailed in our companion paper. PMID:22888758

Simultaneous estimation of liquid and solid gastric emptying using radiolabelled egg and water in supine normal subjects.

PubMed

Kris, M G; Yeh, S D; Gralla, R J; Young, C W

1986-01-01

To develop an additional method for the measurement of gastric emptying in supine subjects, 10 normal subjects were given a test meal containing 99Tc-labelled scrambled egg as the "solid" phase marker and 111In in tapwater as the marker for the "liquid" phase. The mean time for emptying 50% of the "solid" phase (t1/2) was 85 min and 29 min for the "liquid" phase. Three individuals were restudied with a mean difference between the two determinations of 10.8% for the "solid" phase and 6.5% for the "liquid" phase. Twenty-six additional studies attempted have been successfully completed in symptomatic patients with advanced cancer. This method provides a simple and reproducible procedure for the determination of gastric emptying that yields results similar to those reported for other test meals and can be used in debilitated patients.

The effect of solute additions on the steady-state creep behavior of dispersion-strengthened aluminum.

NASA Technical Reports Server (NTRS)

Reynolds, G. H.; Lenel, F. V.; Ansell, G. S.

1971-01-01

The effect of solute additions on the steady-state creep behavior of coarse-grained dispersion-strengthened aluminum alloys was studied. Recrystallized dispersion-strengthened solid solutions were found to have stress and temperature sensitivities quite unlike those observed in single-phase solid solutions having the same composition and grain size. The addition of magnesium or copper to the matrix of a recrystallized dispersion-strengthened aluminum causes a decrease in the steady-state creep rate which is much smaller than that caused by similar amounts of solute in single-phase solid solutions. All alloys exhibited essentially a 4.0 power stress exponent in agreement with the model of Ansell and Weertman. The activation energy for steady-state creep in dispersion-strengthened Al-Mg alloys, as well as the stress dependence, was in agreement with the physical model of dislocation climb over the dispersed particles.

Development of megestrol acetate solid dispersion nanoparticles for enhanced oral delivery by using a supercritical antisolvent process.

PubMed

Ha, Eun-Sol; Kim, Jeong-Soo; Baek, In-Hwan; Yoo, Jin-Wook; Jung, Yunjin; Moon, Hyung Ryong; Kim, Min-Soo

2015-01-01

In the present study, solid dispersion nanoparticles with a hydrophilic polymer and surfactant were developed using the supercritical antisolvent (SAS) process to improve the dissolution and oral absorption of megestrol acetate. The physicochemical properties of the megestrol acetate solid dispersion nanoparticles were characterized using scanning electron microscopy, differential scanning calorimetry, powder X-ray diffraction, and a particle-size analyzer. The dissolution and oral bioavailability of the nanoparticles were also evaluated in rats. The mean particle size of all solid dispersion nanoparticles that were prepared was <500 nm. Powder X-ray diffraction and differential scanning calorimetry measurements showed that megestrol acetate was present in an amorphous or molecular dispersion state within the solid dispersion nanoparticles. Hydroxypropylmethyl cellulose (HPMC) solid dispersion nanoparticles significantly increased the maximum dissolution when compared with polyvinylpyrrolidone K30 solid dispersion nanoparticles. The extent and rate of dissolution of megestrol acetate increased after the addition of a surfactant into the HPMC solid dispersion nanoparticles. The most effective surfactant was Ryoto sugar ester L1695, followed by D-α-tocopheryl polyethylene glycol 1000 succinate. In this study, the solid dispersion nanoparticles with a drug:HPMC:Ryoto sugar ester L1695 ratio of 1:2:1 showed >95% rapid dissolution within 30 minutes, in addition to good oral bioavailability, with approximately 4.0- and 5.5-fold higher area under the curve (0-24 hours) and maximum concentration, respectively, than raw megestrol acetate powder. These results suggest that the preparation of megestrol acetate solid dispersion nanoparticles using the supercritical antisolvent process is a promising approach to improve the dissolution and absorption properties of megestrol acetate.

Digitalizing historical high resolution water level data: Challenges and opportunities

NASA Astrophysics Data System (ADS)

Holinde, Lars; Hein, Hartmut; Barjenbruch, Ulrich

2017-04-01

Historical tide-gauge data offer the opportunities for determining variations in key characteristics for water level data and the analyses of past extreme events (storm surges). These information are important for calculating future trends and scenarios. But there are challenges involved due to the extensive effort needed to digitalize gauge sheets and quality control the resulting historical data. Based on these conditions, two main sources for inaccuracies in historical time series can be identified. First are several challenges due to the digitalization of the historical data, e.g. general quality of the sheets, multiple crossing lines of the observed water levels and additional comments on the sheet describing problems or additional information during the measurements. Second are problems during the measurements themselves. These can include the incorrect positioning of the sheets, trouble with the tide-gauge and maintenance. Errors resulting from these problems can be e.g. flat lines, discontinuities and outlier. Especially, the characterization of outliers has to be conducted carefully, to distinguish between real outliers and the appearance of extreme events. Methods for the quality control process involve the use of statistics, machine learning and neural networks. These will be described and applied to three different time series from tide gauge stations at the cost of Lower Saxony, Germany. Resulting difficulties and outcomes of the quality control process will be presented and explained. Furthermore, we will present a first glance at analyses for these time series.

Improved estimates of filtered total mercury loadings and total mercury concentrations of solids from potential sources to Sinclair Inlet, Kitsap County, Washington

USGS Publications Warehouse

Paulson, Anthony J.; Conn, Kathleen E.; DeWild, John F.

2013-01-01

Previous investigations examined sources and sinks of mercury to Sinclair Inlet based on historic and new data. This included an evaluation of mercury concentrations from various sources and mercury loadings from industrial discharges and groundwater flowing from the Bremerton naval complex to Sinclair Inlet. This report provides new data from four potential sources of mercury to Sinclair Inlet: (1) filtered and particulate total mercury concentrations of creek water during the wet season, (2) filtered and particulate total mercury releases from the Navy steam plant following changes in the water softening process and discharge operations, (3) release of mercury from soils to groundwater in two landfill areas at the Bremerton naval complex, and (4) total mercury concentrations of solids in dry dock sumps that were not affected by bias from sequential sampling. The previous estimate of the loading of filtered total mercury from Sinclair Inlet creeks was based solely on dry season samples. Concentrations of filtered total mercury in creek samples collected during wet weather were significantly higher than dry weather concentrations, which increased the estimated loading of filtered total mercury from creek basins from 27.1 to 78.1 grams per year. Changes in the concentrations and loading of filtered and particulate total mercury in the effluent of the steam plant were investigated after the water softening process was changed from ion-exchange to reverse osmosis and the discharge of stack blow-down wash began to be diverted to the municipal water-treatment plant. These changes reduced the concentrations of filtered and particulate total mercury from the steam plant of the Bremerton naval complex, which resulted in reduced loadings of filtered total mercury from 5.9 to 0.15 grams per year. Previous investigations identified three fill areas on the Bremerton naval complex, of which the western fill area is thought to be the largest source of mercury on the base. Studies of groundwater in the other two fill areas were conducted under worst-case higher high tidal conditions. A December 2011 study found that concentrations of filtered total mercury in the well in the fill area on the eastern boundary of the Bremerton naval complex were less than or equal to 11 nanograms per liter, indicating that releases from the eastern area were unlikely. In addition, concentrations of total mercury of solids were low (<3 milligrams per kilogram). In contrast, data from the November 2011 study indicated that the concentrations of filtered total mercury in the well located in the central fill area had tidally influenced concentrations of up to 500 nanograms per liter and elevated concentrations of total mercury of solids (29–41 milligrams per kilogram). This suggests that releases from this area, which has not been previously studied in detail, may be substantial. Previous measurements of total mercury of suspended solids in the dry dock discharges revealed high concentration of total mercury when suspended-solids concentrations were low. However, this result could have been owing to bias from sequential sampling during changing suspended‑solids concentrations. Sampling of two dry dock systems on the complex in a manner that precluded this bias confirmed that suspended-solids concentrations and total mercury concentrations of suspended solids varied considerably during pumping cycles. These new data result in revised estimates of solids loadings from the dry docks. Although most of the solids discharged by the dry docks seem to be recycled Operable Unit B Marine sediment, a total of about 3.2 metric tons of solids per year containing high concentrations of total mercury were estimated to be discharged by the two dry dock systems. A simple calculation, in which solids (from dry docks, the steam plant, and tidal flushing of the largest stormwater drain) are widely dispersed throughout Operable Unit B Marine, suggests that Bremerton naval complex solids would likely have little effect on Operable Unit B Marine sediments because of high concentrations of mercury already present in the sediment.

Optimization of headspace solid phase microextraction for the analysis of microbial volatile organic compounds emitted by fungi: Application to historical objects.

PubMed

Sawoszczuk, Tomasz; Syguła-Cholewińska, Justyna; del Hoyo-Meléndez, Julio M

2015-08-28

The main goal of this work was to optimize the SPME sampling method for measuring microbial volatile organic compounds (MVOCs) emitted by active molds that may deteriorate historical objects. A series of artificially aged model materials that resemble those found in historical objects was prepared and evaluated after exposure to four different types of fungi. The investigated pairs consisted of: Alternaria alternata on silk, Aspergillus niger on parchment, Chaetomium globosum on paper and wool, and Cladosporium herbarum on paper. First of all, a selection of the most efficient SPME fibers was carried out as there are six different types of fibers commercially available. It was important to find a fiber that absorbs the biggest number and the highest amount of MVOCs. The results allowed establishing and selecting the DVB/CAR/PDMS fiber as the most effective SPME fiber for this kind of an analysis. Another task was to optimize the time of MVOCs extraction on the fiber. It was recognized that a time between 12 and 24h is adequate for absorbing a high enough amount of MVOCs. In the last step the temperature of MVOCs desorption in the GC injection port was optimized. It was found that desorption at a temperature of 250°C allowed obtaining chromatograms with the highest abundances of compounds. To the best of our knowledge this work constitutes the first attempt of the SPME method optimization for sampling MVOCs emitted by molds growing on historical objects. Copyright © 2015 Elsevier B.V. All rights reserved.

Historic Context and Building Assessments for the Lawrence Livermore National Laboratory Built Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ullrich, R. A.; Sullivan, M. A.

2007-09-14

This document was prepared to support u.s. Department of Energy / National Nuclear Security Agency (DOE/NNSA) compliance with Sections 106 and 110 of the National Historic Preservation Act (NHPA). Lawrence Livermore National Laboratory (LLNL) is a DOE/NNSA laboratory and is engaged in determining the historic status of its properties at both its main site in Livermore, California, and Site 300, its test site located eleven miles from the main site. LLNL contracted with the authors via Sandia National Laboratories (SNL) to prepare a historic context statement for properties at both sites and to provide assessments of those properties of potentialmore » historic interest. The report contains an extensive historic context statement and the assessments of individual properties and groups of properties determined, via criteria established in the context statement, to be of potential interest. The historic context statement addresses the four contexts within which LLNL falls: Local History, World War II History (WWII), Cold War History, and Post-Cold War History. Appropriate historic preservation themes relevant to LLNL's history are delineated within each context. In addition, thresholds are identified for historic significance within each of the contexts based on the explication and understanding of the Secretary of the Interior's Guidelines for determining eligibility for the National Register of Historic Places. The report identifies specific research areas and events in LLNL's history that are of interest and the portions of the built environment in which they occurred. Based on that discussion, properties of potential interest are identified and assessments of them are provided. Twenty individual buildings and three areas of potential historic interest were assessed. The final recommendation is that, of these, LLNL has five individual historic buildings, two sets of historic objects, and two historic districts eligible for the National Register. All are eligible within the Cold War History context. They are listed in the table below, along with the Cold War preservation theme, period of significance, and criterion under which they are eligible.« less

State and solubility of cadmium as related to xenotic inorganic phases generated homogeneously in soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, W.J.

The state and solubility of cadmium in waste-treated soils was investigated. Three sets of experiments were designed to elucidate solid phase control of soil solution cadmium. First, the soil solution composition of two soils amended with either sludge or metal contaminated mulch was examined to determine the presence of anions capable of precipitating or co-precipitating cadmium. Results indicated that no known pure solid phases of cadmium developed but that high concentrations of phosphate, sulfate and carbonate apparently influenced cadmium solubility. Secondly, three soils were amended with 10 ug of cadmium as cadmium acetate/g of soil. Three different levels of glycerophosphate,more » cysteine and acetate were added to the soils and incubated at constant temperature and water content in order to release phosphate, sulfate and alkalinity under conditions conducive for homogeneous precipitation. Another set of treatments was prepared in the same fashion with an additional amendment of calcium carbonate to raise soil pH's to 7.0. In the presence of sulfate, cadmium solubility increased with no apparent solid phase formation. The addition of calcium carbonate shifted solid phase control to either calcium carbonate or calcium sulfate. The generation of alkalinity by acetate addition produced solid phase calcium carbonate which in turn controlled cadmium solubility through chemisorption of cadmium on calcite surfaces. In the presence of monobasic calcium phosphate, cadmium was interfacially adsorbed. In the presence of dibasic calcium phosphate, however, cadmium was homogeneously precipitated in the host crystal suggesting possible solid solution.« less

History of Solid Rockets

NASA Technical Reports Server (NTRS)

Green, Rebecca

2017-01-01

Solid rockets are of interest to the space program because they are commonly used as boosters that provide the additional thrust needed for the space launch vehicle to escape the gravitational pull of the Earth. Larger, more advanced solid rockets allow for space launch vehicles with larger payload capacities, enabling mankind to reach new depths of space. This presentation will discuss, in detail, the history of solid rockets. The history begins with the invention and origin of the solid rocket, and then goes into the early uses and design of the solid rocket. The evolution of solid rockets is depicted by a description of how solid rockets changed and improved and how they were used throughout the 16th, 17th, 18th, and 19th centuries. Modern uses of the solid rocket include the Solid Rocket Boosters (SRBs) on the Space Shuttle and the solid rockets used on current space launch vehicles. The functions and design of the SRB and the advancements in solid rocket technology since the use of the SRB are discussed as well. Common failure modes and design difficulties are discussed as well.

Vacuum Flushing of Sewer Solids

EPA Science Inventory

The vacuum sewer and tank cleaning (flushing) technology removes sewer solids from urban drainage systems, such as storage tanks and pipes. This technology is both effective and inexpensive. In addition, it can be considered a true green technology. It operates under atmospheri...

Phase Partitioning from Theanol Blend Gasolines

EPA Science Inventory

In recent years, the use of ethanol and other alcohols as motor fuel additives has increased. Additionally, ethanol production has expanded due to the potential use of ethanol as a primary fuel source. Historical patterns of gasoline composition show strong dependency on regulato...

3. Northwest side and southwest rear of addition. View to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Northwest side and southwest rear of addition. View to east. - Offutt Air Force Base, Looking Glass Airborne Command Post, Aerospace Ground Equipment (AGE) Storage Facility, Far Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

Process for selective grinding of coal

DOEpatents

Venkatachari, Mukund K.; Benz, August D.; Huettenhain, Horst

1991-01-01

A process for preparing coal for use as a fuel. Forming a coal-water slurry having solid coal particles with a particle size not exceeding about 80 microns, transferring the coal-water slurry to a solid bowl centrifuge, and operating same to classify the ground coal-water slurry to provide a centrate containing solid particles with a particle size distribution of from about 5 microns to about 20 microns and a centrifuge cake of solids having a particle size distribution of from about 10 microns to about 80 microns. The classifer cake is reground and mixed with fresh feed to the solid bowl centrifuge for additional classification.

Columbia River System Operation Review : Final Environmental Impact Statement, Appendix D: Cultural Resources.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Columbia River System Operation Review

1995-11-01

This study attempts to identify and analyze the impacts of the System Operating Strategy (SOS) alternatives on cultural resources. The impacts include effects on Native American traditional cultural values, properties and practices. They also include effects on archeological or historic properties meeting the criteria of the National Register of Historic Places. In addition to responding to the requirements of the National Environmental Policy Act (NEPA), this analysis addresses the requirements of the National Historic Preservation Act (NHPA), the Archeological Resources Protection Act (ARPA), the Native American Graves Protection and Repatriation Act (NAGPRA), the Native American Religious Freedom Act (NARFA), andmore » other relevant legislation. To meet their legally mandated cultural resources requirements, the SOR agencies will develop agreements and Implementation Plans with the appropriate State Historic Preservation Officers (SHPOs), Tribes, and the Advisory Council on Historic Preservation (ACHP) detailing the measures necessary to best manage the resource. The planning and implementation activities will be staged over a number of years in consultation with affected Tribes.« less

Modeling the Commuting Travel Activities within Historic Districts in Chinese Cities

PubMed Central

Yin, Fengjun; Hu, Qizhou

2014-01-01

The primary objective of this study is to analyze the characteristics of commuting activities within the historical districts in cities of China. The impacts of various explanatory variables on commuters' travels are evaluated using the structural equation modeling (SEM) approach. The household survey was conducted in the historical districts in Yangzhou, China. Based on the data, various individual and household attributes were considered exogenous variables, while the subsistence activity characteristics, travel times, numbers of three typical home-based trip chains, trip chains, and travel mode were considered as the endogenous variables. Commuters in our study were classified into two main groups according to their working location, which were the commuters in the historic district and those out of the district. The modeling results show that several individual and household attributes of commuters in historic district have significant impacts on the characteristics of travel activities. Additionally, the characteristics of travel activities within the two groups are quite different, and the contributing factors related to commuting travels are different as well. PMID:25435864

Modeling the commuting travel activities within historic districts in Chinese cities.

PubMed

Ye, Mao; Yu, Miao; Li, Zhibin; Yin, Fengjun; Hu, Qizhou

2014-01-01

The primary objective of this study is to analyze the characteristics of commuting activities within the historical districts in cities of China. The impacts of various explanatory variables on commuters' travels are evaluated using the structural equation modeling (SEM) approach. The household survey was conducted in the historical districts in Yangzhou, China. Based on the data, various individual and household attributes were considered exogenous variables, while the subsistence activity characteristics, travel times, numbers of three typical home-based trip chains, trip chains, and travel mode were considered as the endogenous variables. Commuters in our study were classified into two main groups according to their working location, which were the commuters in the historic district and those out of the district. The modeling results show that several individual and household attributes of commuters in historic district have significant impacts on the characteristics of travel activities. Additionally, the characteristics of travel activities within the two groups are quite different, and the contributing factors related to commuting travels are different as well.

Measuring historical trauma in an American Indian Community Sample: Contributions of substance dependence, affective disorder, conduct disorder and PTSD

PubMed Central

Ehlers, Cindy L.; Gizer, Ian R.; Gilder, David A.; Ellingson, Jarrod M.; Yehuda, Rachel

2013-01-01

Background The American Indian experience of historical trauma is thought of as both a source of intergenerational trauma responses as well as a potential causative factor for long-term distress and substance abuse among communities. The aims of the present study were to evaluate the extent to which the frequency of thoughts of historical loss and associated symptoms are influenced by: current traumatic events, post traumatic stress disorder (PTSD), cultural identification, percent Native American Heritage, substance dependence, affective/anxiety disorders, and conduct disorder/antisocial personality disorder (ASPD). Methods Participants were American Indians recruited from reservations that were assessed with the Semi-Structured Assessment for the Genetics of Alcoholism (SSAGA), The Historical Loss Scale and The Historical Loss Associated Symptoms Scale (to quantify frequency of thoughts and symptoms of historical loss) the Stressful-Life-Events Scale (to assess experiences of trauma) and the Orthogonal Cultural Identification Scale (OCIS). Results Three hundred and six (306) American Indian adults participated in the study. Over half of them indicated that they thought about historical losses at least occasionally, and that it caused them distress. Logistic regression revealed that significant increases in how often a person thought about historical losses were associated with: not being married, high degrees of Native Heritage, and high cultural identification. Additionally, anxiety/affective disorders and substance dependence were correlated with historical loss associated symptoms. Conclusions In this American Indian community, thoughts about historical losses and their associated symptomatology are common and the presences of these thoughts are associated with Native American Heritage, cultural identification, and substance dependence. PMID:23791028

Controls on the distribution of arsenic in lake sediments impacted by 65 years of gold ore processing in subarctic Canada: the role of organic matter

NASA Astrophysics Data System (ADS)

Galloway, Jennifer; Palmer, Michael; Swindles, Graeme T.; Sanei, Hamed; Jamieson, Heather E.; Parsons, Michael; Macumber, Andrew L.; Patterson, Tim; Falck, Hendrik

2017-04-01

Gold mines in the Yellowknife region of the Northwest Territories, Canada, operated from 1938 to 2003 and released approximately 20,000 tonnes of arsenic trioxide to the environment through stack emissions. This release resulted in highly elevated arsenic concentrations in lake surface waters and sediments relative to Canadian drinking water standards and guidelines for the protection of aquatic life. High northern latitudes are experiencing substantial impacts, including changes in bio-physico-chemical processes, due to climate change. Determining the affect of warming climate on contamination is complicated by the fact that little is known of climate change controls on As mobility and bioavailability. Further, while the role of dissolved organic matter in As cycling is relatively well characterized in soils and wetland sediments, few studies have investigated the role of solid organic matter in lacustrine systems. We use a meta-analytical approach to better understand controls on sedimentary arsenic distribution in lakes within a 50 km2 area of historic mineral processing activities. Arsenic concentrations in near surface sediments of the 100 lakes studied range from 5 mg/kg to over 10,000 mg/kg (median 81 mg/kg). Distance from the historical Giant Mine roaster stack and the amount of labile organic matter (S1 carbon as determined by Rock Eval pyrolysis) in lake sediments are the variables most strongly correlated with sedimentary As concentrations (Spearman's rank correlation As:distance from historic roaster rs=-0.57, p<0.05; As:S1 rs=0.55, p<0.05). The S1 fraction, volatile hydrocarbons derived from readily degradable geolipids and pigments predominantly originating from authochthonous organic matter, represents a small portion of the overall total organic carbon in the sedimentary material analyzed (median 2.33 wt.%). However, this fraction of organic matter has large potential to influence element concentrations in lake sediments through coating of pre-existing solid-phase As-mineral complexes, direct As-organic matter interactions, and promotion of microbial-mediated reduction and precipitation of As-bearing minerals.

Friction between footwear and floor covered with solid particles under dry and wet conditions.

PubMed

Li, Kai Way; Meng, Fanxing; Zhang, Wei

2014-01-01

Solid particles on the floor, both dry and wet, are common but their effects on the friction on the floor were seldom discussed in the literature. In this study, friction measurements were conducted to test the effects of particle size of solid contaminants on the friction coefficient on the floor under footwear, floor, and surface conditions. The results supported the hypothesis that particle size of solids affected the friction coefficient and the effects depended on footwear, floor, and surface conditions. On dry surfaces, solid particles resulted in friction loss when the Neolite footwear pad was used. On the other hand, solid particles provided additional friction when measured with the ethylene vinyl acetate (EVA) footwear pad. On wet surfaces, introducing solid particles made the floors more slip-resistant and such effects depended on particle size. This study provides information for better understanding of the mechanism of slipping when solid contaminants are present.

Using historical and projected future climate model simulations as drivers of agricultural and biological models (Invited)

NASA Astrophysics Data System (ADS)

Stefanova, L. B.

2013-12-01

Climate model evaluation is frequently performed as a first step in analyzing climate change simulations. Atmospheric scientists are accustomed to evaluating climate models through the assessment of model climatology and biases, the models' representation of large-scale modes of variability (such as ENSO, PDO, AMO, etc) and the relationship between these modes and local variability (e.g. the connection between ENSO and the wintertime precipitation in the Southeast US). While these provide valuable information about the fidelity of historical and projected climate model simulations from an atmospheric scientist's point of view, the application of climate model data to fields such as agriculture, ecology and biology may require additional analyses focused on the particular application's requirements and sensitivities. Typically, historical climate simulations are used to determine a mapping between the model and observed climate, either through a simple (additive for temperature or multiplicative for precipitation) or a more sophisticated (such as quantile matching) bias correction on a monthly or seasonal time scale. Plants, animals and humans however are not directly affected by monthly or seasonal means. To assess the impact of projected climate change on living organisms and related industries (e.g. agriculture, forestry, conservation, utilities, etc.), derivative measures such as the heating degree-days (HDD), cooling degree-days (CDD), growing degree-days (GDD), accumulated chill hours (ACH), wet season onset (WSO) and duration (WSD), among others, are frequently useful. We will present a comparison of the projected changes in such derivative measures calculated by applying: (a) the traditional temperature/precipitation bias correction described above versus (b) a bias correction based on the mapping between the historical model and observed derivative measures themselves. In addition, we will present and discuss examples of various application-based climate model evaluations, such as: (a) agricultural crop yield estimates and (b) species population viability estimates modeled using observed climate data vs. historical climate simulations.

Improving Tribological Properties of Multialkylated Cyclopentanes under Simulated Space Environment: Two Feasible Approaches.

PubMed

Fan, Xiaoqiang; Wang, Liping; Li, Wen; Wan, Shanhong

2015-07-08

Space mechanisms require multialkylated cyclopentanes (MACs) more lubricious, more reliable, more durable, and better adaptive to harsh space environments. In this study, two kinds of additives were added into MACs for improving the tribological properties under simulated space environments: (a) solid nanoparticles (tungsten disulfide (WS2), tungsten trioxide (WO3), lanthanum oxide (La2O3), and lanthanum trifluoride (LaF3)) for steel/steel contacts; (b) liquid additives like zinc dialkyldithiophosphate (ZDDP) and molybdenum dialkyldithiocarbamate (MoDTC) for steel/steel and steel/diamond-like carbon (DLC) contacts. The results show that, under harsh simulated space environments, addition of the solid nanoparticles into MACs allows the wear to be reduced by up to one order magnitude, while liquid additives simultaneously reduce friction and wear by 80% and 93%, respectively. Friction mechanisms were proposed according to surface/interface analysis techniques, such as X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectroscopy (TOF-SIMS). The role of solid nanoparticles in reducing friction and wear mainly depends on their surface enhancement effect, and the liquid additives are attributed to the formation of tribochemical reaction film derived from ZDDP and MoDTC on the sliding surfaces.

The microcomputer scientific software series 9: user's guide to Geo-CLM: geostatistical interpolation of the historical climatic record in the Lake States.

Treesearch

Margaret R. Holdaway

1994-01-01

Describes Geo-CLM, a computer application (for Mac or DOS) whose primary aim is to perform multiple kriging runs to interpolate the historic climatic record at research plots in the Lake States. It is an exploration and analysis tool. Addition capabilities include climatic databases, a flexible test mode, cross validation, lat/long conversion, English/metric units,...

Application of LC-MS to the analysis of dyes in objects of historical interest

NASA Astrophysics Data System (ADS)

Zhang, Xian; Laursen, Richard

2009-07-01

High-performance liquid chromatography (HPLC) with photodiode array and mass spectrometric detection permits dyes extracted from objects of historical interest or from natural plant or animal dyestuffs to be characterized on the basis of three orthogonal properties: HPLC retention time, UV-visible spectrum and molecular mass. In the present study, we have focused primarily on yellow dyes, the bulk of which are flavonoid glycosides that would be almost impossible to characterize without mass spectrometric detection. Also critical for this analysis is a method for mild extraction of the dyes from objects (e.g., textiles) without hydrolyzing the glycosidic linkages. This was accomplished using 5% formic acid in methanol, rather than the more traditional 6 M HCl. Mass spectroscopy, besides providing the molecular mass of the dye molecule, sometimes yields additional structural data based on fragmentation patterns. In addition, coeluting compounds can often be detected using extracted ion chromatography. The utility of mass spectrometry is illustrated by the analysis of historical specimens of silk that had been dyed yellow with flavonoid glycosides from Sophora japonica (pagoda tree) and curcumins from Curcuma longa (turmeric). In addition, we have used these techniques to identify the dye type, and sometimes the specific dyestuff, in a variety of objects, including a yellow varnish from a 19th century Tibetan altar and a 3000-year-old wool mortuary textiles, from Xinjiang, China. We are using HPLC with diode array and mass spectrometric detection to create a library of analyzed dyestuffs (>200 so far; mostly plants) to serve as references for identification of dyes in objects of historical interest.

Field-emission scanning electron microscopy and energy-dispersive x-ray analysis to understand the role of tannin-based dyes in the degradation of historical wool textiles.

PubMed

Restivo, Annalaura; Degano, Ilaria; Ribechini, Erika; Pérez-Arantegui, Josefina; Colombini, Maria Perla

2014-10-01

An innovative approach, combining field-emission scanning electron microscopy (FESEM) with energy dispersive X-ray spectroscopy (EDX) analysis, is presented to investigate the degradation mechanisms affecting tannin-dyed wool. In fact, tannin-dyed textiles are more sensitive to degradation then those dyed with other dyestuffs, even in the same conservation conditions. FESEM-EDX was first used to study a set of 48 wool specimens (artificially aged) dyed with several raw materials and mordants, and prepared according to historical dyeing recipes. EDX analysis was performed on the surface of wool threads and on their cross-sections. In addition, in order to validate the model formulated by the analysis of reference materials, several samples collected from historical and archaeological textiles were subjected to FESEM-EDX analysis. FESEM-EDX investigations enabled us to reveal the correlation between elemental composition and morphological changes. In addition, aging processes were clarified by studying changes in the elemental composition of wool from the protective cuticle to the fiber core in cross-sections. Morphological and elemental analysis of wool specimens and of archaeological and historical textiles showed that the presence of tannins increases wool damage, primarily by causing a sulfur decrease and fiber oxidation.

Koppen bioclimatic evaluation of CMIP historical climate simulations

DOE PAGES

Phillips, Thomas J.; Bonfils, Celine J. W.

2015-06-05

Köppen bioclimatic classification relates generic vegetation types to characteristics of the interactive annual-cycles of continental temperature (T) and precipitation (P). In addition to predicting possible bioclimatic consequences of past or prospective climate change, a Köppen scheme can be used to pinpoint biases in model simulations of historical T and P. In this study a Köppen evaluation of Coupled Model Intercomparison Project (CMIP) simulations of historical climate is conducted for the period 1980–1999. Evaluation of an example CMIP5 model illustrates how errors in simulating Köppen vegetation types (relative to those derived from observational reference data) can be deconstructed and related tomore » model-specific temperature and precipitation biases. Measures of CMIP model skill in simulating the reference Köppen vegetation types are also developed, allowing the bioclimatic performance of a CMIP5 simulation of T and P to be compared quantitatively with its CMIP3 antecedent. Although certain bioclimatic discrepancies persist across model generations, the CMIP5 models collectively display an improved rendering of historical T and P relative to their CMIP3 counterparts. Additionally, the Köppen-based performance metrics are found to be quite insensitive to alternative choices of observational reference data or to differences in model horizontal resolution.« less

Rescuing biogeographic legacy data: The "Thor" Expedition, a historical oceanographic expedition to the Mediterranean Sea

PubMed Central

Mavraki, Dimitra; Fanini, Lucia; Tsompanou, Marilena; Gerovasileiou, Vasilis; Nikolopoulou, Stamatina; Chatzinikolaou, Eva; Plaitis, Wanda

2016-01-01

Abstract Background This article describes the digitization of a series of historical datasets based οn the reports of the 1908–1910 Danish Oceanographical Expeditions to the Mediterranean and adjacent seas. All station and sampling metadata as well as biodiversity data regarding calcareous rhodophytes, pelagic polychaetes, and fish (families Engraulidae and Clupeidae) obtained during these expeditions were digitized within the activities of the LifeWatchGreece Research Ιnfrastructure project and presented in the present paper. The aim was to safeguard public data availability by using an open access infrastructure, and to prevent potential loss of valuable historical data on the Mediterranean marine biodiversity. New information The datasets digitized here cover 2,043 samples taken at 567 stations during a time period from 1904 to 1930 in the Mediterranean and adjacent seas. The samples resulted in 1,588 occurrence records of pelagic polychaetes, fish (Clupeiformes) and calcareous algae (Rhodophyta). In addition, basic environmental data (e.g. sea surface temperature, salinity) as well as meterological conditions are included for most sampling events. In addition to the description of the digitized datasets, a detailed description of the problems encountered during the digitization of this historical dataset and a discussion on the value of such data are provided. PMID:28174510

Microclimate Exposures of Surface-Based Weather Stations: Implications For The Assessment of Long-Term Temperature Trends.

NASA Astrophysics Data System (ADS)

Davey, Christopher A.; Pielke, Roger A., Sr.

2005-04-01

The U.S. Historical Climate Network is a subset of surface weather observation stations selected from the National Weather Service cooperative station network. The criteria used to select these stations do not sufficiently address station exposure characteristics. In addition, the current metadata available for cooperative network stations generally do not describe site exposure characteristics in sufficient detail. This paper focuses on site exposures with respect to air temperature measurements. A total of 57 stations were photographically surveyed in eastern Colorado, comparing existing exposures to the standards endorsed by the World Meteorological Organization. The exposures of most sites surveyed, including U.S. Historical Climate Network sites, were observed to fall short of these standards. This raises a critical question about the use of many Historical Climate Network sites in the development of long-term climate records and the detection of climate trends. Some of these sites clearly have poor exposures and therefore should be considered for removal from the Historical Climate Network. Candidate replacement sites do exist and should be considered for addition into the network to replace the removed sites. Documentation as performed for this study should be conducted worldwide in order to determine the extent of spatially nonrepresentative exposures and possible temperature biases.

Vacuum Flushing of Sewer Solids (Slides)

EPA Science Inventory

The vacuum sewer and tank cleaning (flushing) technology removes sewer solids from urban drainage systems, such as storage tanks and pipes. This technology is both effective and inexpensive. In addition, it can be considered a true green technology. It operates under atmospheri...

Turbulence modeling of gas-solid suspension flows

NASA Technical Reports Server (NTRS)

Chen, C. P.

1988-01-01

The purpose here is to discuss and review advances in two-phase turbulent modeling techniques and their applications in various gas-solid suspension flow situations. In addition to the turbulence closures, heat transfer effect, particle dispersion and wall effects are partially covered.

Urban History in 4 Dimensions - Supporting Research and Education

NASA Astrophysics Data System (ADS)

Münster, S.; Friedrichs, K.; Kröber, C.; Bruschke, J.; Henze, F.; Maiwald, F.; Niebling, F.

2017-08-01

The new research group on the four-dimensional research and communication of urban history (Urban History 4D) aims to investigate and develop methods and technologies to access extensive repositories of historical media and their contextual information in a spatial model, with an additional temporal component. This will make content accessible to different target groups, researchers and the public, via a 4D browser. A location-dependent augmented-reality representation can be used as an information base, research tool, and means of communicating historical knowledge. The data resources for this research include extensive holdings of historical photographs of Dresden, which have documented the city over the decades, and digitized map collections from the Deutsche Fotothek (German photographic collection) platform. These will lay the foundation for a prototype model which will give users a virtual experience of historic parts of Dresden.

Effect of Periodic Water Addition on Citric Acid Production in Solid State Fermentation

NASA Astrophysics Data System (ADS)

Utpat, Shraddha S.; Kinnige, Pallavi T.; Dhamole, Pradip B.

2013-09-01

Water addition is one of the methods used to control the moisture loss in solid state fermentation (SSF). However, none of the studies report the timing of water addition and amount of water to be added in SSF. Therefore, this work was undertaken with an objective to evaluate the performance of periodic water addition on citric acid production in SSF. Experiments were conducted at different moistures (50-80 %) and temperatures (30-40 °C) to simulate the conditions in a fermenter. Citric acid production by Aspergillus niger (ATCC 9029) using sugarcane baggase was chosen as a model system. Based on the moisture profile, citric acid and sugar data, a strategy was designed for periodic addition of water. Water addition at 48, 96, 144 and 192 h enhanced the citric acid production by 62 % whereas water addition at 72, 120, and 168 h increased the citric acid production by just 17 %.

Airborne concentrations of metals and total dust during solid catalyst loading and unloading operations at a petroleum refinery.

PubMed

Lewis, Ryan C; Gaffney, Shannon H; Le, Matthew H; Unice, Ken M; Paustenbach, Dennis J

2012-09-01

Workers handle catalysts extensively at petroleum refineries throughout the world each year; however, little information is available regarding the airborne concentrations and plausible exposures during this type of work. In this paper, we evaluated the airborne concentrations of 15 metals and total dust generated during solid catalyst loading and unloading operations at one of the largest petroleum refineries in the world using historical industrial hygiene samples collected between 1989 and 2006. The total dust and metals, which included aluminum, cadmium, chromium, cobalt, copper, iron, lead, manganese, molybdenum, nickel, platinum, silicon, silver, vanadium, and zinc, were evaluated in relation to the handling of four different types of solid catalysts associated with three major types of catalytic processes. Consideration was given to the known components of the solid catalysts and any metals that were likely deposited onto them during use. A total of 180 analytical results were included in this analysis, representing 13 personal and 54 area samples. Of the long-term personal samples, airborne concentrations of metals ranged from <0.001 to 2.9mg/m(3), and, in all but one case, resulted in concentrations below the current U.S. Occupational Safety and Health Administration's Permissible Exposure Limits and the American Conference of Governmental Industrial Hygienists' Threshold Limit Values. The arithmetic mean total dust concentration resulting from long-term personal samples was 0.31mg/m(3). The data presented here are the most complete set of its kind in the open literature, and are useful for understanding the potential exposures during solid catalyst handling activities at this petroleum refinery and perhaps other modern refineries during the timeframe examined. Copyright © 2011 Elsevier GmbH. All rights reserved.

Application of transglycosylated stevia and hesperidin as drug carriers to enhance biopharmaceutical properties of poorly-soluble artemisinin.

PubMed

Letchmanan, Kumaran; Shen, Shou-Cang; Ng, Wai Kiong; Tan, Reginald B H

2018-01-01

Biopharmaceutical properties of poorly water-soluble antimalarial drug, Artemisinin (ART), were improved by formulating amorphous solid dispersions with transglycosylated food additives (Hsp-G and Stevia-G) via co-spray drying. Both the formulated ART/Hsp-G and ART/Stevia-G showed superior dissolution properties with a burst release of more than 95% of drug within 5 min, whereas untreated ART dissolved only 4% in 5min. The supersaturation solubility of the formulated ART was enhanced by 2-fold as compared with untreated counterpart. The storage stability tests indicated that these formulations chemically stable at room temperature and under low humidity (<18% RH) conditions. However, high humidity (75% RH) induced re-crystallization and caused changes in the physical appearance of the solid dispersions. In addition, both the food additives and ART formulated samples showed low cytotoxicity to Caco-2 cell line suggesting their good biocompatibility. Thus, the formation of solid dispersions of ART with transglycosylated food additives is a potentially safe and effective approach to enhance the bioavailability of poorly water-soluble ART. Copyright © 2017 Elsevier B.V. All rights reserved.

Investigation on Dynamic Calibration for an Optical-Fiber Solids Concentration Probe in Gas-Solid Two-Phase Flows

PubMed Central

Xu, Guiling; Liang, Cai; Chen, Xiaoping; Liu, Daoyin; Xu, Pan; Shen, Liu; Zhao, Changsui

2013-01-01

This paper presents a review and analysis of the research that has been carried out on dynamic calibration for optical-fiber solids concentration probes. An introduction to the optical-fiber solids concentration probe was given. Different calibration methods of optical-fiber solids concentration probes reported in the literature were reviewed. In addition, a reflection-type optical-fiber solids concentration probe was uniquely calibrated at nearly full range of the solids concentration from 0 to packed bed concentration. The effects of particle properties (particle size, sphericity and color) on the calibration results were comprehensively investigated. The results show that the output voltage has a tendency to increase with the decreasing particle size, and the effect of particle color on calibration result is more predominant than that of sphericity. PMID:23867745

Erosive Burning of Composite Solid Propellants: Experimental and Modeling Studies

DTIC Science & Technology

1978-08-01

of Crossflow on Solid Pro- appears that an additional mechanism(s) of erosive pallant Combustion: Interior Ballistic Design burning will have to be...Orlondo, Florida, July , 1977, AIAA Paper 77-930. 14. Lengelle,G., "Model Describing the Erosive Com- bustion and Velocity Response of Composite Pro...Propulsion Conference, Orlando, Florida, July , 1977. 17. Beddini, R.A., A Reacting Turbulent Boundary Layer Approach to Solid Propellant Erosive Burning, AFOSR

Solid lubrication design methodology, phase 2

NASA Technical Reports Server (NTRS)

Pallini, R. A.; Wedeven, L. D.; Ragen, M. A.; Aggarwal, B. B.

1986-01-01

The high temperature performance of solid lubricated rolling elements was conducted with a specially designed traction (friction) test apparatus. Graphite lubricants containing three additives (silver, phosphate glass, and zinc orthophosphate) were evaluated from room temperature to 540 C. Two hard coats were also evaluated. The evaluation of these lubricants, using a burnishing method of application, shows a reasonable transfer of lubricant and wear protection for short duration testing except in the 200 C temperature range. The graphite lubricants containing silver and zinc orthophosphate additives were more effective than the phosphate glass material over the test conditions examined. Traction coefficients ranged from a low of 0.07 to a high of 0.6. By curve fitting the traction data, empirical equations for slope and maximum traction coefficient as a function of contact pressure (P), rolling speed (U), and temperature (T) can be developed for each lubricant. A solid lubricant traction model was incorporated into an advanced bearing analysis code (SHABERTH). For comparison purposes, preliminary heat generation calculations were made for both oil and solid lubricated bearing operation. A preliminary analysis indicated a significantly higher heat generation for a solid lubricated ball bearing in a deep groove configuration. An analysis of a cylindrical roller bearing configuration showed a potential for a low friction solid lubricated bearing.

Space Shuttle Solid Rocket Booster Lightweight Recovery System

NASA Technical Reports Server (NTRS)

Wolf, Dean; Runkle, Roy E.

1995-01-01

The cancellation of the Advanced Solid Rocket Booster Project and the earth-to-orbit payload requirements for the Space Station dictated that the National Aeronautics and Space Administration (NASA) look at performance enhancements from all Space Transportation System (STS) elements (Orbiter Project, Space Shuttle Main Engine Project, External Tank Project, Solid Rocket Motor Project, & Solid Rocket Booster Project). The manifest for launching of Space Station components indicated that an additional 12-13000 pound lift capability was required on 10 missions and 15-20,000 pound additional lift capability is required on two missions. Trade studies conducted by all STS elements indicate that by deleting the parachute Recovery System (and associated hardware) from the Solid Rocket Boosters (SRBS) and going to a lightweight External Tank (ET) the 20,000 pound additional lift capability can be realized for the two missions. The deletion of the parachute Recovery System means the loss of four SRBs and this option is two expensive (loss of reusable hardware) to be used on the other 10 Space Station missions. Accordingly, each STS element looked at potential methods of weight savings, increased performance, etc. As the SRB and ET projects are non-propulsive (i.e. does not have launch thrust elements) their only contribution to overall payload enhancement can be achieved by the saving of weight while maintaining adequate safety factors and margins. The enhancement factor for the SRB project is 1:10. That is for each 10 pounds saved on the two SRBS; approximately 1 additional pound of payload in the orbiter bay can be placed into orbit. The SRB project decided early that the SRB recovery system was a prime candidate for weight reduction as it was designed in the early 1970s and weight optimization had never been a primary criteria.

Selenium Speciation and Management in Wet FGD Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Searcy, K; Richardson, M; Blythe, G

2012-02-29

This report discusses results from bench- and pilot-scale simulation tests conducted to determine the factors that impact selenium speciation and phase partitioning in wet FGD systems. The selenium chemistry in wet FGD systems is highly complex and not completely understood, thus extrapolation and scale-up of these results may be uncertain. Control of operating parameters and application of scrubber additives have successfully demonstrated the avoidance or decrease of selenite oxidation at the bench and pilot scale. Ongoing efforts to improve sample handling methods for selenium speciation measurements are also discussed. Bench-scale scrubber tests explored the impacts of oxidation air rate, tracemore » metals, scrubber additives, and natural limestone on selenium speciation in synthetic and field-generated full-scale FGD liquors. The presence and concentration of redox-active chemical species as well as the oxidation air rate contribute to the oxidation-reduction potential (ORP) conditions in FGD scrubbers. Selenite oxidation to the undesirable selenate form increases with increasing ORP conditions, and decreases with decreasing ORP conditions. Solid-phase manganese [Mn(IV)] appeared to be the significant metal impacting the oxidation of selenite to selenate. Scrubber additives were tested for their ability to inhibit selenite oxidation. Although dibasic acid and other scrubber additives showed promise in early clear liquor (sodium based and without calcium solids) bench-scale tests, these additives did not show strong inhibition of selenite oxidation in tests with higher manganese concentrations and with slurries from full-scale wet FGD systems. In bench-tests with field liquors, addition of ferric chloride at a 250:1 iron-to-selenium mass ratio sorbed all incoming selenite to the solid phase, although addition of ferric salts had no impact on native selenate that already existed in the field slurry liquor sample. As ORP increases, selenite may oxidize to selenate more rapidly than it sorbs to ferric solids. Though it was not possible to demonstrate a decrease in selenium concentrations to levels below the project'ale testing were evident at the pilot scale. Specifically, reducing oxidation air rate and ORP tends to either retain selenium as selenite in the liquor or shift selenium phase partitioning to the solid phase. Oxidation air flow rate control may be one option for managing selenium behavior in FGD scrubbers. Units that cycle load widely may find it more difficult to impact ORP conditions with oxidation air flow rate control alone. Because decreasing oxidation air rates to the reaction tank showed that all new selenium reported to the solids, the addition of ferric chloride to the pilot scrubber could not show further improvements in selenium behavior. Ferric chloride addition did shift mercury to the slurry solids, specifically to the fine particles. Several competing pathways may govern the reporting of selenium to the slurry solids: co-precipitation with gypsum into the bulk solids and sorption or co-precipitation with iron into the fine particles. Simultaneous measurement of selenium and mercury behavior suggests a holistic management strategy is best to optimize the fate of both of these elements in FGD waters. Work conducted under this project evaluated sample handling and analytical methods for selenium speciation in FGD waters. Three analytical techniques and several preservation methods were employed. Measurements of selenium speciation over time indicated that for accurate selenium speciation, it is best to conduct measurements on unpreserved, filtered samples as soon after sampling as possible. The capital and operating costs for two selenium management strategies were considered: ferric chloride addition and oxidation air flow rate control. For ferric chloride addition, as might be expected the reagent makeup costs dominate the overall costs, and range from 0.22 to 0.29 mills/kWh. For oxidation air flow rate control, a cursory comparison of capital costs and turndown capabilities for multi-stage and single-stage centrifugal blowers and several flow control methods was completed. For greenfield systems, changing the selection of blower type and flow control method may have payback periods of 4 to 5 years or more if based on energy savings alone. However, the benefits to managing redox chemistry in the scrubber could far outweigh the savings in electricity costs under some circumstances.« less

An analysis of the orbital distribution of solid rocket motor slag

NASA Astrophysics Data System (ADS)

Horstman, Matthew F.; Mulrooney, Mark

2009-01-01

The contribution by solid rocket motors (SRMs) to the orbital debris environment is potentially significant and insufficiently studied. Design and combustion processes can lead to the emission of enough by-products to warrant assessment of their contribution to orbital debris. These particles are formed during SRM tail-off, or burn termination, by the rapid solidification of molten Al2O3 slag accumulated during the burn. The propensity of SRMs to generate particles larger than 100μm raises concerns regarding the debris environment. Sizes as large as 1 cm have been witnessed in ground tests, and comparable sizes have been estimated via observations of sub-orbital tail-off events. Utilizing previous research we have developed more sophisticated size distributions and modeled the time evolution of resultant orbital populations using a historical database of SRM launches, propellant, and likely location and time of tail-off. This analysis indicates that SRM ejecta is a significant component of the debris environment.

Bringing Solid-State Magnetocaloric Cooling to the Market: A Commercialization Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abu-Heiba, Ahmad; Sikes, Karen; Blackburn, Julia

Air conditioning has become a staple in American life, bringing improved health, productivity, and comfort to 93% of single-family homes as of 2015, compared to only 76% in 1990. This rise in demand has contributed to the 2.51 quads (12.5%) of total annual energy consumption in residential buildings attributable to space cooling (U.S. Energy Information Administration 2017). Accompanying this upward trend in space cooling has been increased refrigerant use, which has historically contributed to ozone depletion, global warming, or both. The Oak Ridge National Laboratory – along with German-based partner Vacuumschmelze GmbH & Co. KG – is working to reducemore » energy consumption and refrigerant use through the development of a next-generation, solid-state magnetocaloric cooling system. The purpose of this study is to investigate market potential of these systems in the United States, including information on the industry landscape, market share and unit shipment projections, optimal price points, and barriers to market entry.« less

Simulation of Blast Loading on an Ultrastructurally-based Computational Model of the Ocular Lens

DTIC Science & Technology

2015-10-01

cells) is stressed by the passing shock wave. Traumatic cataract can result in a partially or fully clouded lens, complete dislo- cation of the lens...penetration by Intra-Ocular Foreign Bodies (IOFBs), but also shock propagation and solid-fluid interaction be- tween the lens and vitreous and aqueous...1040-8738. doi: 10.1097/ICU.0b013e3283140e98. T.Y. Wong, M.B. Seet, and C.L. Ang. Eye injuries in twentieth century warfare: A historical perspective. Survey of Ophthalmology, 41(6):433–459, MAY-JUN 1997. ISSN 0039-6257. i

There Must Be A-Way (to Deal with Solid Waste).

ERIC Educational Resources Information Center

Fortner, Rosanne W.

1991-01-01

Presents a class project to help upper elementary students grasp the extent of the solid waste disposal problem and develop an individual response. Includes background information for the teacher, project objectives, materials, procedures, and a listing for additional resources. (MCO)

40 CFR 240.200-2 - Recommended procedures: Design.

Code of Federal Regulations, 2011 CFR

2011-07-01

....200-2 Section 240.200-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.200-2 Recommended procedures: Design. (a) In addition to the residential and commercial wastes...

40 CFR 240.200-2 - Recommended procedures: Design.

Code of Federal Regulations, 2010 CFR

2010-07-01

....200-2 Section 240.200-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.200-2 Recommended procedures: Design. (a) In addition to the residential and commercial wastes...

Assessment of Solid Sorbent Systems for Post-Combustion Carbon Dioxide Capture at Coal-Fired Power Plants

NASA Astrophysics Data System (ADS)

Glier, Justin C.

In an effort to lower future CO2 emissions, a wide range of technologies are being developed to scrub CO2 from the flue gases of fossil fuel-based electric power and industrial plants. This thesis models one of several early-stage post-combustion CO2 capture technologies, solid sorbent-based CO2 capture process, and presents performance and cost estimates of this system on pulverized coal power plants. The spreadsheet-based software package Microsoft Excel was used in conjunction with AspenPlus modelling results and the Integrated Environmental Control Model to develop performance and cost estimates for the solid sorbent-based CO2 capture technology. A reduced order model also was created to facilitate comparisons among multiple design scenarios. Assumptions about plant financing and utilization, as well as uncertainties in heat transfer and material design that affect heat exchanger and reactor design were found to produce a wide range of cost estimates for solid sorbent-based systems. With uncertainties included, costs for a supercritical power plant with solid sorbent-based CO2 capture ranged from 167 to 533 per megawatt hour for a first-of-a-kind installation (with all costs in constant 2011 US dollars) based on a 90% confidence interval. The median cost was 209/MWh. Post-combustion solid sorbent-based CO2 capture technology is then evaluated in terms of the potential cost for a mature system based on historic experience as technologies are improved with sequential iterations of the currently available system. The range costs for a supercritical power plant with solid sorbent-based CO2 capture was found to be 118 to 189 per megawatt hour with a nominal value of 163 per megawatt hour given the expected range of technological improvement in the capital and operating costs and efficiency of the power plant after 100 GW of cumulative worldwide experience. These results suggest that the solid sorbent-based system will not be competitive with currently available liquid amine-systems in the absence of significant new improvements in solid sorbent properties and process system design to reduce the heat exchange surface area in the regenerator and cross-flow heat exchanger. Finally, the importance of these estimates for policy makers is discussed.

An Investigation into the Comparative Costs of Additive Manufacture vs. Machine from Solid for Aero Engine Parts

DTIC Science & Technology

2006-05-01

welding power sources are not totally efficient at converting power drawn from the wall into heat energy used for the welding process . TIG sources are...Powder bed + Laser • Wire + Laser • Wire + Electron Beam • Wire + TIG Each system has its own unique attributes in terms of process variables...relative economics of producing a near net shape by Additive Manufacturing (AM) processes compared with traditional machine from solid processes (MFS

1. Northeast front and southeast side of original section. Addition ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Northeast front and southeast side of original section. Addition to rear view to west. - Offutt Air Force Base, Looking Glass Airborne Command Post, Aerospace Ground Equipment (AGE) Storage Facility, Far Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

Reactor performance and energy analysis of solid state anaerobic co-digestion of dairy manure with corn stover and tomato residues.

PubMed

Li, Yangyang; Xu, Fuqing; Li, Yu; Lu, Jiaxin; Li, Shuyan; Shah, Ajay; Zhang, Xuehua; Zhang, Hongyu; Gong, Xiaoyan; Li, Guoxue

2018-03-01

Anaerobic co-digestion is commonly believed to be benefical for biogas production. However, additional of co-substrates may require additional energy inputs and thus affect the overall energy efficiency of the system. In this study, reactor performance and energy analysis of solid state anaerobic digestion (SS-AD) of tomato residues with dairy manure and corn stover were investigated. Different fractions of tomato residues (0, 20, 40, 60, 80 and 100%, based on volatile solid weight (VS)) were co-digested with dairy manure and corn stover at 15% total solids. Energy analysis based on experimental data was conducted for three scenarios: SS-AD of 100% dairy manure, SS-AD of binary mixture (60% dairy manure and 40% corn stover, VS based), and SS-AD of ternary mixture (36% dairy manure, 24% corn stover, and 40% tomato residues, VS based). For each scenario, the energy requirements for individual process components, including feedstock collection and transportation, feedstock pretreatment, biogas plant operation, digestate processing and handling, and the energy production were examined. Results showed that the addition of 20 and 40% tomato residues increased methane yield compared to that of the dairy manure and corn stover mixture, indicating that the co-digestion could balance nutrients and improve the performance of solid-state anaerobic digestion. The energy required for heating substrates had the dominant effect on the total energy consumption. The highest volatile solids (VS) reduction (57.0%), methane yield (379.1 L/kg VS feed ), and net energy production were achieved with the mixture of 24% corn stover, 36% dairy manure, and 40% tomato residues. Thus, the extra energy input for adding tomato residues for co-digestion could be compensated by the increase of methane yield. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effects of flue gas desulfurization (FGD) system additives on solid by-products. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huyck, K.A.; Tatum, G.S.; DeKraker, D.P.

This study was designed to examine characteristics of by-products from flue gas desulfurization (FGD) systems that use performance-enhancing additives. The by-products were evaluated for handling, disposal, properties, and utilization potential. This study was designed to identify potential operation-limiting consequences (fatal flaws) caused by using FGD system additives. It was not intended to be an all-encompassing study of the possible process, environmental, and utilization circumstances at each plant. Seven utilities conducting additive testing agreed to provide samples for this study both before and during their testing. Solid samples were collected from FGD systems using the following additives: di-basic acid (DBA), whichmore » is a mixture of succinic, glutaric, and adipic acids; formate; sulfur; ethylene diamine tetraacetic acid (EDTA); and chloride. Changes in handling properties that may alter process operations were observed at sites where DBS was used. Changes in leaching behavior, permeability and unconfined compressive strength (properties that affect by-product disposal properties) showed no clear trend for additive or system type. The intent of this study is to provide an overall assessment of potential system-limiting effects of FGD additive use. There were no overriding problems relating to disposal with the use of additives. However, properties of solids produced with and without additives should be tested at each site prior to use of an FGD system additive. This is necessary because of the variability in state disposal and permitting requirements and the influence of specific operating conditions on by-product properties.« less

Risk for transmission of Naegleria fowleri from solid organ transplantation.

PubMed

Roy, S L; Metzger, R; Chen, J G; Laham, F R; Martin, M; Kipper, S W; Smith, L E; Lyon, G M; Haffner, J; Ross, J E; Rye, A K; Johnson, W; Bodager, D; Friedman, M; Walsh, D J; Collins, C; Inman, B; Davis, B J; Robinson, T; Paddock, C; Zaki, S R; Kuehnert, M; DaSilva, A; Qvarnstrom, Y; Sriram, R; Visvesvara, G S

2014-01-01

Primary amebic meningoencephalitis (PAM) caused by the free-living ameba (FLA) Naegleria fowleri is a rare but rapidly fatal disease of the central nervous system (CNS) affecting predominantly young, previously healthy persons. No effective chemotherapeutic prophylaxis or treatment has been identified. Recently, three transplant-associated clusters of encephalitis caused by another FLA, Balamuthia mandrillaris, have occurred, prompting questions regarding the suitability of extra-CNS solid organ transplantation from donors with PAM. During 1995-2012, 21 transplant recipients of solid organs donated by five patients with fatal cases of PAM were reported in the United States. None of the recipients developed PAM, and several recipients tested negative for N. fowleri by serology. However, historical PAM case reports and animal experiments with N. fowleri, combined with new postmortem findings from four patients with PAM, suggest that extra-CNS dissemination of N. fowleri can occur and might pose a risk for disease transmission via transplantation. The risks of transplantation with an organ possibly harboring N. fowleri should be carefully weighed for each individual recipient against the potentially greater risk of delaying transplantation while waiting for another suitable organ. In this article, we present a case series and review existing data to inform such risk assessments. © Copyright 2013 The American Society of Transplantation and the American Society of Transplant Surgeons.

Risk for Transmission of Naegleria fowleri from Solid Organ Transplantation

PubMed Central

Roy, SL; Metzger, R; Chen, JG; Laham, FR; Martin, M; Kipper, SW; Smith, LE; Lyon, GM; Haffner, J; Ross, JE; Rye, AK; Johnson, W; Bodager, D; Friedman, M; Walsh, DJ; Collins, C; Inman, B; Davis, BJ; Robinson, T; Paddock, C; Zaki, SR; Kuehnert, M; DaSilva, A; Qvarnstrom, Y; Sriram, R; Visvesvara, GS

2015-01-01

Primary amebic meningoencephalitis (PAM) caused by the free-living ameba Naegleria fowleri is a rare but rapidly fatal disease of the central nervous system (CNS) affecting predominantly young, previously healthy persons. No effective chemotherapeutic prophylaxis or treatment has been identified. Recently, three transplant-associated clusters of encephalitis caused by another free-living ameba, Balamuthia mandrillaris, have occurred, prompting questions regarding the suitability of extra-CNS solid organ transplantation from donors with PAM. During 1995–2012, 21 transplant recipients of solid organs donated by five patients with fatal cases of PAM were reported in the United States. None of the recipients developed PAM and several recipients tested negative for N. fowleri by serology. However, historical PAM case reports and animal experiments with N. fowleri, combined with new post-mortem findings from four PAM patients, suggest that extra-CNS dissemination of N. fowleri can occur and might pose a risk for disease transmission via transplantation. The risks of transplantation with an organ possibly harboring N. fowleri should be carefully weighed for each individual recipient against the potentially greater risk of delaying transplantation while waiting for another suitable organ. In this article we present a case series and review existing data to inform such risk assessments. PMID:24279908

A Historical Study of the Effectiveness of U.S. Security Assistance to Panama, Costa Rica and Nicaragua

DTIC Science & Technology

1986-09-01

United States aid to the rebels (16:9). The United States policy toward Central America originated with the Monroe Doctrine. As explained in Chapter...crisis in the area. The most often used were Mexico and Central America Report, Latinamerica Press, Mesoamerica , and Hemisphere Hotline. Especially...Information Exchange (DLSIE) and the Defense Technical Information Center (DTIC) to determine what studies were available. In addition, the historical

New solid-state chemistry technologies to bring better drugs to market: knowledge-based decision making.

PubMed

Park, Aeri; Chyall, Leonard J; Dunlap, Jeanette; Schertz, Christine; Jonaitis, David; Stahly, Barbara C; Bates, Simon; Shipplett, Rex; Childs, Scott

2007-01-01

Modern drug development demands constant deployment of more effective technologies to mitigate the high cost of bringing new drugs to market. In addition to cost savings, new technologies can improve all aspects of pharmaceutical development. New technologies developed at SSCI, Inc. include solid form development of an active pharmaceutical ingredients. (APIs) are PatternMatch software and capillary-based crystallisation techniques that not only allow for fast and effective solid form screening, but also extract maximum property information from the routine screening data that is generally available. These new technologies offer knowledge-based decision making during solid form development of APIs and result in more developable API solid forms.

Measurement of electromagnetic properties of powder and solid metal materials for additive manufacturing

NASA Astrophysics Data System (ADS)

Todorov, Evgueni Iordanov

2017-04-01

The lack of validated nondestructive evaluation (NDE) techniques for examination during and after additive manufacturing (AM) component fabrication is one of the obstacles in the way of broadening use of AM for critical applications. Knowledge of electromagnetic properties of powder (e.g. feedstock) and solid AM metal components is necessary to evaluate and deploy electromagnetic NDE modalities for examination of AM components. The objective of this research study was to develop and implement techniques for measurement of powder and solid metal electromagnetic properties. Three materials were selected - Inconel 625, duplex stainless steel 2205, and carbon steel 4140. The powder properties were measured with alternate current (AC) model based eddy current technique and direct current (DC) resistivity measurements. The solid metal properties were measured with DC resistivity measurements, DC magnetic techniques, and AC model based eddy current technique. Initial magnetic permeability and electrical conductivity were acquired for both powder and solid metal. Additional magnetic properties such as maximum permeability, coercivity, retentivity, and others were acquired for 2205 and 4140. Two groups of specimens were tested along the build length and width respectively to investigate for possible anisotropy. There was no significant difference or anisotropy when comparing measurements acquired along build length to those along the width. A trend in AC measurements might be associated with build geometry. Powder electrical conductivity was very low and difficult to estimate reliably with techniques used in the study. The agreement between various techniques was very good where adequate comparison was possible.

High temperature solid electrolyte fuel cell with ceramic electrodes

DOEpatents

Marchant, David D.; Bates, J. Lambert

1984-01-01

A solid oxide electrolyte fuel cell is described having a central electrolyte comprised of a HfO.sub.2 or ZrO.sub.2 ceramic stabilized and rendered ionically conductive by the addition of Ca, Mg, Y, La, Nd, Sm, Gd, Dy Er, or Yb. The electrolyte is sandwiched between porous electrodes of a HfO.sub.2 or ZrO.sub.2 ceramic stabilized by the addition of a rare earth and rendered electronically conductive by the addition of In.sub.2 O.sub.3. Alternatively, the anode electrode may be made of a metal such as Co, Ni, Ir Pt, or Pd.

High temperature solid electrolyte fuel cell with ceramic electrodes

DOEpatents

Bates, J.L.; Marchant, D.D.

A solid oxide electrolyte fuel cell is described having a central electrolyte comprised of a HfO/sub 2/ or ZrO/sub 2/ ceramic stabilized and rendered ionically conductive by the addition of Ca, Mg, Y, La, Nd, Sm, Gd, Dy Er, or Yb. The electrolyte is sandwiched between porous electrodes of a HfO/sub 2/ or ZrO/sub 2/ ceramic stabilized by the addition of a rare earth and rendered electronically conductive by the addition of In/sub 2/O/sub 3/. Alternatively, the anode electrode may be made of a metal such as Co, Ni, Ir Pt, or Pd.

Optimization of high solids fed-batch saccharification of sugarcane bagasse based on system viscosity changes.

PubMed

Liu, Yunyun; Xu, Jingliang; Zhang, Yu; Yuan, Zhenhong; Xie, Jun

2015-10-10

Viscosity trends in alkali-pretreated sugarcane bagasse (SCB) slurries undergoing high solids fed-batch enzymatic hydrolysis were measured for a range of solids loading from 15% to 36%. Solids liquefaction times were related to system viscosity changes. The viscosity decreased quickly for low solids loading, and increased with increasing solids content. Fed-batch hydrolysis was initiated with 15% solids loading, and an additional 8%, 7% and 6% were successively added after the system viscosity decreased to stable values to achieve a final solids content of 36%. Two enzyme-adding modes with 8.5FPU/g solid were investigated. The batch mode with all enzyme being added at the beginning of the reaction produced the highest yields, with approximately 231.7g/L total sugars and 134.9g/L glucose being obtained after 96h with nearly 60% of the final glucan conversion rate. This finding indicates that under the right conditions, the fed-batch strategy might be a plausible way to produce high sugars under high solids. Copyright © 2015 Elsevier B.V. All rights reserved.

Measuring historical trauma in an American Indian community sample: contributions of substance dependence, affective disorder, conduct disorder and PTSD.

PubMed

Ehlers, Cindy L; Gizer, Ian R; Gilder, David A; Ellingson, Jarrod M; Yehuda, Rachel

2013-11-01

The American Indian experience of historical trauma is thought of as both a source of intergenerational trauma responses as well as a potential causative factor for long-term distress and substance abuse among communities. The aims of the present study were to evaluate the extent to which the frequency of thoughts of historical loss and associated symptoms are influenced by: current traumatic events, post traumatic stress disorder (PTSD), cultural identification, percent Native American Heritage, substance dependence, affective/anxiety disorders, and conduct disorder/antisocial personality disorder (ASPD). Participants were American Indians recruited from reservations that were assessed with the Semi-Structured Assessment for the Genetics of Alcoholism (SSAGA), The Historical Loss Scale and The Historical Loss Associated Symptoms Scale (to quantify frequency of thoughts and symptoms of historical loss) the Stressful-Life-Events Scale (to assess experiences of trauma) and the Orthogonal Cultural Identification Scale (OCIS). Three hundred and six (306) American Indian adults participated in the study. Over half of them indicated that they thought about historical losses at least occasionally, and that it caused them distress. Logistic regression revealed that significant increases in how often a person thought about historical losses were associated with: not being married, high degrees of Native Heritage, and high cultural identification. Additionally, anxiety/affective disorders and substance dependence were correlated with historical loss associated symptoms. In this American Indian community, thoughts about historical losses and their associated symptomatology are common and the presence of these thoughts are associated with Native American Heritage, cultural identification, and substance dependence. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

The Historical Loss Scale: Longitudinal measurement equivalence and prospective links to anxiety among North American indigenous adolescents.

PubMed

Armenta, Brian E; Whitbeck, Les B; Habecker, Patrick N

2016-01-01

Thoughts of historical loss (i.e., the loss of culture, land, and people as a result of colonization) are conceptualized as a contributor to the contemporary distress experienced by North American Indigenous populations. Although discussions of historical loss and related constructs (e.g., historical trauma) are widespread within the Indigenous literature, empirical efforts to understand the consequence of historical loss are limited, partially because of the lack of valid assessments. In this study we evaluated the longitudinal measurement properties of the Historical Loss Scale (HLS)-a standardized measure that was developed to systematically examine the frequency with which Indigenous individuals think about historical loss-among a sample of North American Indigenous adolescents. We also test the hypothesis that thoughts of historical loss can be psychologically distressing. Via face-to-face interviews, 636 Indigenous adolescents from a single cultural group completed the HLS and a measure of anxiety at 4 time-points, which were separated by 1- to 2-year intervals (Mage = 12.09 years, SD = .86, 50.0% girls at baseline). Responses to the HLS were explained well by 3-factor (i.e., cultural loss, loss of people, and cultural mistreatment) and second-order factor structures. Both of these factor structures held full longitudinal metric (i.e., factor loadings) and scalar (i.e., intercepts) equivalence. In addition, using the second-order factor structure, more frequent thoughts of historical loss were associated with increased anxiety. The identified 3-factor and second-order HLS structures held full longitudinal measurement equivalence. Moreover, as predicted, our results suggest that historical loss can be psychologically distressing for Indigenous adolescents. (c) 2016 APA, all rights reserved).

15 CFR 922.40 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-01-01

... continued availability of the conservation, ecological, recreational, research, educational, historical and aesthetic resources and qualities of these areas. Additional purposes of the regulations implementing the...

Solid State Nuclear Magnetic Resonance Studies of the Murchison Organic Macromolecule

NASA Technical Reports Server (NTRS)

Cody, G. D., III; Alexander, C. M. OD.; Tera, F.

2001-01-01

We have used high speed H-1 (DEPTH) and C-13 (VACP MAS-slow spinning) solid state NMR to determine the contributions of protonated vs non-protonated carbon in the Murchison Macromolecule. Additional information is contained in the original extended abstract.

Survey of dissolved air flotation system efficiency for reduce of pollution of vegetable oil industry wastewater.

PubMed

Keramati, H; Alidadi, H; Parvaresh, A R; Movahedian, H; Mahvi, A H

2008-10-01

The aim of this research was to sudy the reduction of pollution of vegetable oil manufacturing wastewater with DAF system. At first phase of this examination, the optimum dosage of the coagulants was determined. The coagulants that used in this study were Alum and Ferric Chloride. The second phase was flotation in this series of examinations, oil, COD, total solid, volatile solid, fixed solid and suspended solid measured in raw wastewater and the effluent of the DAF pilot. Optimum value of pH for alum and ferric chloride obtained 7.5 and 5.5, respectively. Optimum dosage for these obtained 30 and 32 mg L(-1) in this research. Mean removal for the parameters ofoil, COD, total solid, volatile solid, fixed solid and suspended solid obtained 75.85, 78.27, 77.32, 82.47, 73.52 and 85.53%, respectively. With pressure rising from 3 to 4 and 5 atm removing rate of COD, total solid, volatile solid, fixed solid parameters reduced, but oil and suspended solid have increase. In addition, following increase of flotation time up to 120 sec all of the measured parameters have increase in removing rate. Optimum A/S for removal of COD, total solid, volatile solid, fixed solid parameters obtained 0.001 and for oil and suspended solid obtained 0.0015.

Solid state photosensitive devices which employ isolated photosynthetic complexes

DOEpatents

Peumans, Peter; Forrest, Stephen R.

2009-09-22

Solid state photosensitive devices including photovoltaic devices are provided which comprise a first electrode and a second electrode in superposed relation; and at least one isolated Light Harvesting Complex (LHC) between the electrodes. Preferred photosensitive devices comprise an electron transport layer formed of a first photoconductive organic semiconductor material, adjacent to the LHC, disposed between the first electrode and the LHC; and a hole transport layer formed of a second photoconductive organic semiconductor material, adjacent to the LHC, disposed between the second electrode and the LHC. Solid state photosensitive devices of the present invention may comprise at least one additional layer of photoconductive organic semiconductor material disposed between the first electrode and the electron transport layer; and at least one additional layer of photoconductive organic semiconductor material, disposed between the second electrode and the hole transport layer. Methods of generating photocurrent are provided which comprise exposing a photovoltaic device of the present invention to light. Electronic devices are provided which comprise a solid state photosensitive device of the present invention.

Investigation of Rhodopsin Dynamics in its Signaling State by Solid-State Deuterium NMR Spectroscopy

PubMed Central

Struts, Andrey V.; Chawla, Udeep; Perera, Suchithranga M.D.C.; Brown, Michael F.

2017-01-01

Site-directed deuterium NMR spectroscopy is a valuable tool to study the structural dynamics of biomolecules in cases where solution NMR is inapplicable. Solid-state 2H NMR spectral studies of aligned membrane samples of rhodopsin with selectively labeled retinal provide information on structural changes of the chromophore in different protein states. In addition, solid-state 2H NMR relaxation time measurements allow one to study the dynamics of the ligand during the transition from the inactive to the active state. Here we describe the methodological aspects of solid-state 2H NMR spectroscopy for functional studies of rhodopsin, with an emphasis on the dynamics of the retinal cofactor. We provide complete protocols for the preparation of NMR samples of rhodopsin with 11-cis-retinal selectively deuterated at the methyl groups in aligned membranes. In addition, we review optimized conditions for trapping the rhodopsin photointermediates; and lastly we address the challenging problem of trapping the signaling state of rhodopsin in aligned membrane films. PMID:25697522

Experimental investigation of the combustion products in an aluminised solid propellant

NASA Astrophysics Data System (ADS)

Liu, Zhu; Li, Shipeng; Liu, Mengying; Guan, Dian; Sui, Xin; Wang, Ningfei

2017-04-01

Aluminium is widely used as an important additive to improve ballistic and energy performance in solid propellants, but the unburned aluminium does not contribute to the specific impulse and has both thermal and momentum two-phase flow losses. So understanding of aluminium combustion behaviour during solid propellant burning is significant when improving internal ballistic performance. Recent developments and experimental results reported on such combustion behaviour are presented in this paper. A variety of experimental techniques ranging from quenching and dynamic measurement, to high-speed CCD video recording, were used to study aluminium combustion behaviour and the size distribution of the initial agglomerates. This experimental investigation also provides the size distribution of the condensed phase products. Results suggest that the addition of an organic fluoride compound to solid propellant will generate smaller diameter condensed phase products due to sublimation of AlF3. Lastly, a physico-chemical picture of the agglomeration process was also developed based on the results of high-speed CCD video analysis.

Possibilities of municipal solid waste incinerator fly ash utilisation.

PubMed

Hartmann, Silvie; Koval, Lukáš; Škrobánková, Hana; Matýsek, Dalibor; Winter, Franz; Purgar, Amon

2015-08-01

Properties of the waste treatment residual fly ash generated from municipal solid waste incinerator fly ash were investigated in this study. Six different mortar blends with the addition of the municipal solid waste incinerator fly ash were evaluated. The Portland cement replacement levels of the municipal solid waste incinerator fly ash used were 25%, 30% and 50%. Both, raw and washed municipal solid waste incinerator fly ash samples were examined. According to the mineralogical composition measurements, a 22.6% increase in the pozzolanic/hydraulic properties was observed for the washed municipal solid waste incinerator fly ash sample. The maximum replacement level of 25% for the washed municipal solid waste incinerator fly ash in mortar blends was established in order to preserve the compressive strength properties. Moreover, the leaching characteristics of the crushed mortar blend was analysed in order to examine the immobilisation of its hazardous contents. © The Author(s) 2015.

Biogas production from the mechanically pretreated, liquid fraction of sorted organic municipal solid wastes.

PubMed

Alvarado-Lassman, A; Méndez-Contreras, J M; Martínez-Sibaja, A; Rosas-Mendoza, E S; Vallejo-Cantú, N A

2017-06-01

The high liquid content in fruit and vegetable wastes makes it convenient to mechanically separate these wastes into mostly liquid and solid fractions by means of pretreatment. Then, the liquid fraction can be treated using a high-rate anaerobic biofilm reactor to produce biogas, simultaneously reducing the amount of solids that must be landfilled. In this work, the specific composition of municipal solid waste (MSW) in a public market was determined; then, the sorted organic fraction of municipal solid waste was treated mechanically to separate and characterize the mostly liquid and solid fractions. Then, the mesophilic anaerobic digestion for biogas production of the first fraction was evaluated. The anaerobic digestion resulted in a reduced hydraulic retention time of two days with high removal of chemical oxygen demand, that is, 88% on average, with the additional benefit of reducing the mass of the solids that had to be landfilled by about 80%.

A circumcision method in an old surgical textbook (Cerrahiyyetul Haniyye): reminding of a forgotten procedure.

PubMed

Senayli, Atilla; Aksu, Murat; Atalar, Munir

2014-07-08

Circumcision is one of the historical surgical procedures. Some sources throughout the history contain various definitions about different circumcision methods. we described the details of the method, and aimed to remind the possibility of contemporary usage. We compared circumcision chapters of Sabuncuoglu and Zahrawi to explain the historical origin of Sabuncuoglu's favorite circumcision method. We found a method which might be summarized as "knotting with rope technique" in one of historical textbooks named as Cerrahiyyetul Haniyye (Imperial Surgery) written by Serefeddin Sabuncuoglu (1385-1468?) in 1465. This circumcision method is not used currently. In addition this method has not been defined in the history of medical literature yet.

Examination and notes to the astronomical records in >SUISHU<.

NASA Astrophysics Data System (ADS)

Liu, Ciyuan

1996-06-01

Astronomical records are an important part in Chinese official historical books. Their main purpose was for astrology and they are an obstacle for historians who read those books. With modern astronomical methods, one can compute and examine most of those ancient records. By comparing the computed results with the original texts, one can examine the texts, find their mistakes, study their observation method and regulation, inspect astrological theory, take a deeper understanding to those important historical materials. As an example the author deals with the astronomcial records of Dynasties Liang and Chen for 60 years in >SUISHU<, the official history of Dynasty Sui. He also synthesized other historical sources in addition to the astronomical computation.

Land subsidence near oil and gas fields, Houston, Texas.

USGS Publications Warehouse

Holzer, T.L.; Bluntzer, R.L.

1984-01-01

Subsidence profiles across 29 oil and gas fields in the 12 200 km2 Houston, Texas, regional subsidence area, which is caused by the decline of ground-water level, suggest that the contribution of petroleum withdrawal to local land subsidence is small. In addition to land subsidence, faults with an aggregate length of more than 240 km have offset the land surface in historical time. Natural geologic deformation, ground-water pumping, and petroleum withdrawal have all been considered as potential causes of the historical offset across these faults. The minor amount of localized land subsidence associated with oil and gas fields, suggests that petroleum withdrawal is not a major cause of the historical faulting. -from Authors

EnviroAtlas - Austin, TX - Historic Places by Census Block Group

EPA Pesticide Factsheets

This EnviroAtlas dataset portrays the total number of historic places located within each Census Block Group (CBG). The historic places data were compiled from the National Register of Historic Places, which provides official federal lists of districts, sites, buildings, structures and objects significant to American history, architecture, archeology, engineering, and culture.This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

[The proof of paternity. An andrological-forensic challenge in historical perspective].

PubMed

Albrecht, K; Schultheiss, D

2004-10-01

For centuries, difficulties have occurred in determining unresolved paternities. In addition to the modern standard methods, such as the examination of DNA or serological proof, expert opinion on fertility once played an important role. The andrological difference between incapability to fertilise and the inability to participate in sexual intercourse was also distinguished historically. Of special significance was the discovery of spermatozoa by the medical student Johan Ham in 1677 and their further investigation by Antoni van Leeuwenhoek.Recently, modern DNA methods have also been applied for historical investigations. Illustrious examples are the DNA analysis in the case of Kaspar Hauser of Ansbach and the dispute about Thomas Jefferson, President of the U.S., fathering a child by one of his slaves. In this discourse, a medicinal-forensic review of the development of expert opinion, illustrated with historical case studies, is given.

Historical warming reduced due to enhanced land carbon uptake.

PubMed

Shevliakova, Elena; Stouffer, Ronald J; Malyshev, Sergey; Krasting, John P; Hurtt, George C; Pacala, Stephen W

2013-10-15

Previous studies have demonstrated the importance of enhanced vegetation growth under future elevated atmospheric CO2 for 21st century climate warming. Surprisingly no study has completed an analogous assessment for the historical period, during which emissions of greenhouse gases increased rapidly and land-use changes (LUC) dramatically altered terrestrial carbon sources and sinks. Using the Geophysical Fluid Dynamics Laboratory comprehensive Earth System Model ESM2G and a reconstruction of the LUC, we estimate that enhanced vegetation growth has lowered the historical atmospheric CO2 concentration by 85 ppm, avoiding an additional 0.31 ± 0.06 °C warming. We demonstrate that without enhanced vegetation growth the total residual terrestrial carbon flux (i.e., the net land flux minus LUC flux) would be a source of 65-82 Gt of carbon (GtC) to atmosphere instead of the historical residual carbon sink of 186-192 GtC, a carbon saving of 251-274 GtC.

Nanoporous adsorption effect on altering Li+ diffusion pathway by a highly ordered porous electrolyte additive for high rate all-solid-state lithium metal batteries.

PubMed

Li, Wenwen; Zhang, Sanpei; Wang, Bangrun; Gu, Sui; Xu, Dong; Wang, Jianing; Chen, Chunhua; Wen, Zhaoyin

2018-06-19

Solid polymer electrolytes (SPEs) have shown extraordinary promise for all-solid-state lithium metal batteries with high energy density and flexibility but are mainly limited by the low ionic conductivity and their poor stability with lithium metal anode. In this work, we propose a highly ordered porous electrolyte additive derived from SSZ-13 for high-rate all-solid-state lithium metal batteries. The nanoporous adsorption effect provided by the highly ordered porous nanoparticles in the poly (ethylene oxide) (PEO) electrolyte are found to significantly improve the Li + conductivity (1.91×10 -3 S cm -1 at 60°C, 4.43×10 -5 S cm -1 at 20°C) and widen the electrochemical stability window to 4.7 V vs Li + /Li. Meanwhile, the designed PEO-based electrolyte demonstrates enhanced stability with the lithium metal anode. Through systematically increasing Li + diffusion, widening the electrochemical stability window and enhancing the stability of the SSZ-CPE electrolyte, the LiFePO4/SSZ-CPE/Li cell is optimized to deliver high-rate capability and stable cycling performance, which demonstrates great potential for all-solid-state energy storage application.

Haptics-based dynamic implicit solid modeling.

PubMed

Hua, Jing; Qin, Hong

2004-01-01

This paper systematically presents a novel, interactive solid modeling framework, Haptics-based Dynamic Implicit Solid Modeling, which is founded upon volumetric implicit functions and powerful physics-based modeling. In particular, we augment our modeling framework with a haptic mechanism in order to take advantage of additional realism associated with a 3D haptic interface. Our dynamic implicit solids are semi-algebraic sets of volumetric implicit functions and are governed by the principles of dynamics, hence responding to sculpting forces in a natural and predictable manner. In order to directly manipulate existing volumetric data sets as well as point clouds, we develop a hierarchical fitting algorithm to reconstruct and represent discrete data sets using our continuous implicit functions, which permit users to further design and edit those existing 3D models in real-time using a large variety of haptic and geometric toolkits, and visualize their interactive deformation at arbitrary resolution. The additional geometric and physical constraints afford more sophisticated control of the dynamic implicit solids. The versatility of our dynamic implicit modeling enables the user to easily modify both the geometry and the topology of modeled objects, while the inherent physical properties can offer an intuitive haptic interface for direct manipulation with force feedback.

On the Superficial Gas Velocity in Deep Gas-Solid Fluidized Beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Tingwen; Grace, John; Shadle, Lawrence

2011-11-15

The superficial gas velocity is one of the key parameters used to determine the flow hydrodynamics in gas–solids fluidized beds. However, the superficial velocity varies with height in practice, and there is no consistent basis for its specification. Different approaches to determine the superficial gas velocity in a deep gas–solids system are shown to cause difficulties in developing models and in comparing predictions with experimental results. In addition, the reference conditions for superficial gas velocity are important in modeling of deep gas–solids systems where there is a considerable pressure drop.

Exploring hardness enhancement in superhard tungsten tetraboride-based solid solutions using radial X-ray diffraction

DOE PAGES

Xie, Miao; Mohammadi, Reza; Turner, Christopher L.; ...

2015-07-29

In this paper, we explore the hardening mechanisms in WB4-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under nonhydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB 4 solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

SMP: A solid modeling program version 2.0

NASA Technical Reports Server (NTRS)

Randall, D. P.; Jones, K. H.; Vonofenheim, W. H.; Gates, R. L.; Matthews, C. G.

1986-01-01

The Solid Modeling Program (SMP) provides the capability to model complex solid objects through the composition of primitive geometric entities. In addition to the construction of solid models, SMP has extensive facilities for model editing, display, and analysis. The geometric model produced by the software system can be output in a format compatible with existing analysis programs such as PATRAN-G. The present version of the SMP software supports six primitives: boxes, cones, spheres, paraboloids, tori, and trusses. The details for creating each of the major primitive types is presented. The analysis capabilities of SMP, including interfaces to existing analysis programs, are discussed.

Development of a publicly available, comprehensive database of fiber and health outcomes: rationale and methods

USDA-ARS?s Scientific Manuscript database

Background: Dietary fiber is a broad category of compounds historically defined as partially or completely indigestible plant-based carbohydrates and lignin with, more recently, the additional criteria that fibers incorporated into foods as additives should demonstrate functional human health outcom...

DOUBLE SHELL TANK (DST) INTEGRITY PROJECT HIGH LEVEL WASTE CHEMISTRY OPTIMIZATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

WASHENFELDER DJ

2008-01-22

The U.S. Department of Energy's Office (DOE) of River Protection (ORP) has a continuing program for chemical optimization to better characterize corrosion behavior of High-Level Waste (HLW). The DOE controls the chemistry in its HLW to minimize the propensity of localized corrosion, such as pitting, and stress corrosion cracking (SCC) in nitrate-containing solutions. By improving the control of localized corrosion and SCC, the ORP can increase the life of the Double-Shell Tank (DST) carbon steel structural components and reduce overall mission costs. The carbon steel tanks at the Hanford Site are critical to the mission of safely managing stored HLWmore » until it can be treated for disposal. The DOE has historically used additions of sodium hydroxide to retard corrosion processes in HLW tanks. This also increases the amount of waste to be treated. The reactions with carbon dioxide from the air and solid chemical species in the tank continually deplete the hydroxide ion concentration, which then requires continued additions. The DOE can reduce overall costs for caustic addition and treatment of waste, and more effectively utilize waste storage capacity by minimizing these chemical additions. Hydroxide addition is a means to control localized and stress corrosion cracking in carbon steel by providing a passive environment. The exact mechanism that causes nitrate to drive the corrosion process is not yet clear. The SCC is less of a concern in the newer stress relieved double shell tanks due to reduced residual stress. The optimization of waste chemistry will further reduce the propensity for SCC. The corrosion testing performed to optimize waste chemistry included cyclic potentiodynamic volarization studies. slow strain rate tests. and stress intensity factor/crack growth rate determinations. Laboratory experimental evidence suggests that nitrite is a highly effective:inhibitor for pitting and SCC in alkaline nitrate environments. Revision of the corrosion control strategies to a nitrite-based control, where there is no constant depletion mechanism as with hydroxide, should greatly enhance tank lifetime, tank space availability, and reduce downstream reprocessing costs by reducing chemical addition to the tanks.« less

Coarsening in Solid-Liquid Mixtures Studied on the Space Shuttle

NASA Technical Reports Server (NTRS)

Caruso, John J.

1999-01-01

Ostwald ripening, or coarsening, is a process in which large particles in a two-phase mixture grow at the expense of small particles. It is a ubiquitous natural phenomena occurring in the late stages of virtually all phase separation processes. In addition, a large number of commercially important alloys undergo coarsening because they are composed of particles embedded in a matrix. Many of them, such as high-temperature superalloys used for turbine blade materials and low-temperature aluminum alloys, coarsen in the solid state. In addition, many alloys, such as the tungsten-heavy metal systems, coarsen in the solid-liquid state during liquid phase sintering. Numerous theories have been proposed that predict the rate at which the coarsening process occurs and the shape of the particle size distribution. Unfortunately, these theories have never been tested using a system that satisfies all the assumptions of the theory. In an effort to test these theories, NASA studied the coarsening process in a solid-liquid mixture composed of solid tin particles in a liquid lead-tin matrix. On Earth, the solid tin particles float to the surface of the sample, like ice in water. In contrast, in a microgravity environment this does not occur. The microstructures in the ground- and space-processed samples (see the photos) show clearly the effects of gravity on the coarsening process. The STS-83-processed sample (right image) shows nearly spherical uniformly dispersed solid tin particles. In contrast, the identically processed, ground-based sample (left image) shows significant density-driven, nonspherical particles, and because of the higher effective solid volume fraction, a larger particle size after the same coarsening time. The "Coarsening in Solid-Liquid Mixtures" (CSLM) experiment was conducted in the Middeck Glovebox facility (MGBX) flown aboard the shuttle in the Microgravity Science Laboratory (MSL-1/1R) on STS-83/94. The primary objective of CSLM is to measure the temporal evolution of the solid particles during coarsening.

Ultimate strength performance of tankers associated with industry corrosion addition practices

NASA Astrophysics Data System (ADS)

Kim, Do Kyun; Kim, Han Byul; Zhang, Xiaoming; Li, Chen Guang; Paik, Jeom Kee

2014-09-01

In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR), Common Structural Rules (CSR), and harmonised Common Structural Rules (CSRH) are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS), and Time-Dependent Corrosion Wastage Model (TDCWM). To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures

Superior Blends Solid Polymer Electrolyte with Integrated Hierarchical Architectures for All-Solid-State Lithium-Ion Batteries.

PubMed

Zhang, Dechao; Zhang, Long; Yang, Kun; Wang, Hongqiang; Yu, Chuang; Xu, Di; Xu, Bo; Wang, Li-Min

2017-10-25

Exploration of advanced solid electrolytes with good interfacial stability toward electrodes is a highly relevant research topic for all-solid-state batteries. Here, we report PCL/SN blends integrating with PAN-skeleton as solid polymer electrolyte prepared by a facile method. This polymer electrolyte with hierarchical architectures exhibits high ionic conductivity, large electrochemical windows, high degree flexibility, good flame-retardance ability, and thermal stability (workable at 80 °C). Additionally, it demonstrates superior compatibility and electrochemical stability toward metallic Li as well as LiFePO 4 cathode. The electrolyte/electrode interfaces are very stable even subjected to 4.5 V at charging state for long time. The LiFePO 4 /Li all-solid-state cells based on this electrolyte deliver high capacity, outstanding cycling stability, and superior rate capability better than those based on liquid electrolyte. This solid polymer electrolyte is eligible for next generation high energy density all-solid-state batteries.

Polyelectrolyte flocculation of grain stillage for improved clarification and water recovery within bioethanol production facilities.

PubMed

Menkhaus, Todd J; Anderson, Jason; Lane, Samuel; Waddell, Evan

2010-04-01

Polyelectrolytes were investigated for flocculation of a corn whole stillage stream to improve solid-liquid clarification operations and reduce downstream utility requirements for evaporation and drying within a bioethanol process. Despite a negative zeta potential for the stillage solids, an anionic polyelectrolyte was found to provide the best flocculation. At the optimal dosage of 1.1mg polymer/g dry suspended solids, an anionic flocculant provided a clarified stream with only 0.15% w/w suspended solids (equivalent to a total dissolved solid to total suspended solid ratio greater than 40, and a viscosity reduction of 39% compared to an unflocculated "clarified" stream). The resulting solids cake had greater than 40% w/w solids, and more than 80% water recovery was found in the clarified stream. Addition of flocculant improved filtration flux by six fold and/or would allow for up to a 4-times higher flow rate if using a decanting centrifuge for clarification of corn stillage. Copyright 2009 Elsevier Ltd. All rights reserved.

Solid state recorders for airborne reconnaissance

NASA Astrophysics Data System (ADS)

Klang, Mark R.

2003-08-01

Solid state recorders have become the recorder of choice for meeting airborne ruggedized requirements for reconnaissance and flight test. The cost of solid state recorders have decreased over the past few years that they are now less expense than the traditional high speed tape recorders. CALCULEX, Inc manufactures solid state recorders called MONSSTR (Modular Non-volatile Solid State Recorder). MONSSTR is being used on many different platforms such as F/A-22, Global Hawk, F-14, F-15, F-16, U-2, RF-4, and Tornado. This paper will discuss the advantages of using solid state recorders to meet the airborne reconnaissance requirement and the ability to record instrumentation data. The CALCULEX recorder has the ability to record sensor data and flight test data in the same chassis. This is an important feature because it eliminates additional boxes on the aircraft. The major advantages to using a solid state recorder include; reliability, small size, light weight, and power. Solid state recorders also have a larger storage capacity and higher bandwidth capability than other recording devices.

Is earthquake rate in south Iceland modified by seasonal loading?

NASA Astrophysics Data System (ADS)

Jonsson, S.; Aoki, Y.; Drouin, V.

2017-12-01

Several temporarily varying processes have the potential of modifying the rate of earthquakes in the south Iceland seismic zone, one of the two most active seismic zones in Iceland. These include solid earth tides, seasonal meteorological effects and influence from passing weather systems, and variations in snow and glacier loads. In this study we investigate the influence these processes may have on crustal stresses and stressing rates in the seismic zone and assess whether they appear to be influencing the earthquake rate. While historical earthquakes in the south Iceland have preferentially occurred in early summer, this tendency is less clear for small earthquakes. The local earthquake catalogue (going back to 1991, magnitude of completeness < 1.0) has indeed more earthquakes in summer than in winter. However, this pattern is strongly influenced by aftershock sequences of the largest M6+ earthquakes, which occurred in June 2000 and May 2008. Standard Reasenberg earthquake declustering or more involved model independent stochastic declustering algorithms are not capable of fully eliminating the aftershocks from the catalogue. We therefore inspected the catalogue for the time period before 2000 and it shows limited seasonal tendency in earthquake occurrence. Our preliminary results show no clear correlation between earthquake rates and short-term stressing variations induced from solid earth tides or passing storms. Seasonal meteorological effects also appear to be too small to influence the earthquake activity. Snow and glacier load variations induce significant vertical motions in the area with peak loading occurring in Spring (April-May) and maximum unloading in Fall (Sept.-Oct.). Early summer occurrence of historical earthquakes therefore correlates with early unloading rather than with the peak unloading or unloading rate, which appears to indicate limited influence of this seasonal process on the earthquake activity.

Results of Characterization and Retrieval Testing on Tank 241-C-109 Heel Solids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Callaway, William S.

Eight samples of heel solids from tank 241-C-109 were delivered to the 222-S Laboratory for characterization and dissolution testing. After being drained thoroughly, one-half to two-thirds of the solids were off-white to tan solids that, visually, were fairly evenly graded in size from coarse silt (30-60 μm) to medium pebbles (8-16 mm). The remaining solids were mostly strongly cemented aggregates ranging from coarse pebbles (16-32 mm) to fine cobbles (6-15 cm) in size. Solid phase characterization and chemical analysis indicated that the air-dry heel solids contained ≈58 wt% gibbsite [Al(OH){sub 3}] and ≈37 wt% natrophosphate [Na{sub 7}F(PO{sub 4}){sub 2}·19H{sub 2}O].more » The strongly cemented aggregates were mostly fine-grained gibbsite cemented with additional gibbsite. Dissolution testing was performed on two test samples. One set of tests was performed on large pieces of aggregate solids removed from the heel solids samples. The other set of dissolution tests was performed on a composite sample prepared from well-drained, air-dry heel solids that were crushed to pass a 1/4-in. sieve. The bulk density of the composite sample was 2.04 g/mL. The dissolution tests included water dissolution followed by caustic dissolution testing. In each step of the three-step water dissolution tests, a volume of water approximately equal to 3 times the initial volume of the test solids was added. In each step, the test samples were gently but thoroughly mixed for approximately 2 days at an average ambient temperature of 25 °C. The caustic dissolution tests began with the addition of sufficient 49.6 wt% NaOH to the water dissolution residues to provide ≈3.1 moles of OH for each mole of Al estimated to have been present in the starting composite sample and ≈2.6 moles of OH for each mole of Al potentially present in the starting aggregate sample. Metathesis of gibbsite to sodium aluminate was then allowed to proceed over 10 days of gentle mixing of the test samples at temperatures ranging from 26-30 °C. The metathesized sodium aluminate was then dissolved by addition of volumes of water approximately equal to 1.3 times the volumes of caustic added to the test slurries. Aluminate dissolution was allowed to proceed for 2 days at ambient temperatures of ≈29 °C. Overall, the sequential water and caustic dissolution tests dissolved and removed 80.0 wt% of the tank 241-C-109 crushed heel solids composite test sample. The 20 wt% of solids remaining after the dissolution tests were 85-88 wt% gibbsite. If the density of the residual solids was approximately equal to that of gibbsite, they represented ≈17 vol% of the initial crushed solids composite test sample. In the water dissolution tests, addition of a volume of water ≈6.9 times the initial volume of the crushed solids composite was sufficient to dissolve and recover essentially all of the natrophosphate present. The ratio of the weight of water required to dissolve the natrophosphate solids to the estimated weight of natrophosphate present was 8.51. The Environmental Simulation Program (OLI Systems, Inc., Morris Plains, New Jersey) predicts that an 8.36 w/w ratio would be required to dissolve the estimated weight of natrophosphate present in the absence of other components of the heel solids. Only minor amounts of Al-bearing solids were removed from the composite solids in the water dissolution tests. The caustic metathesis/aluminate dissolution test sequence, executed at temperatures ranging from 27-30 °C, dissolved and recovered ≈69 wt% of the gibbsite estimated to have been present in the initial crushed heel solids composite. This level of gibbsite recovery is consistent with that measured in previous scoping tests on the dissolution of gibbsite in strong caustic solutions. Overall, the sequential water and caustic dissolution tests dissolved and removed 80.3 wt% of the tank 241-C-109 aggregate solids test sample. The residual solids were 92-95 wt% gibbsite. Only a minor portion (≈4.5 wt%) of the aggregate solids was dissolved and recovered in the water dissolution test. Other than some smoothing caused by continuous mixing, the aggregates were essentially unaffected by the water dissolution tests. During the caustic metathesis/aluminate dissolution test sequence, ≈81 wt% of the gibbsite estimated to have been present in the aggregate solids was dissolved and recovered. The pieces of aggregate were significantly reduced in size but persisted as distinct pieces of solids. The increased level of gibbsite recovery, as compared to that for the crushed heel solids composite, suggests that the way the gibbsite solids and caustic solution are mixed is a key determinant of the overall efficiency of gibbsite dissolution and recovery. The liquids recovered after the caustic dissolution tests on the crushed solids composite and the aggregate solids were observed for 170 days. No precipitation of gibbsite was observed. The distribution of particle sizes in the residual solids recovered following the dissolution tests on the crushed heel solids composite was characterized. Wet sieving indicated that 21.4 wt% of the residual solids were >710 μm in size, and laser light scattering indicated that the median equivalent spherical diameter in the <710-μm solids was 35 μm. The settling behavior of the residual solids following the large-scale dissolution tests was also studied. When dispersed at a concentration of ≈1 vol% in water, ≈24 wt% of the residual solids settled at a rate >0.43 in./s; ≈68 wt% settled at rates between 0.02 and 0.43 in./s; and ≈7 wt% settled slower than 0.02 in./s.« less

Mackay campus of environmental education and digital cultural construction: the application of 3D virtual reality

NASA Astrophysics Data System (ADS)

Chien, Shao-Chi; Chung, Yu-Wei; Lin, Yi-Hsuan; Huang, Jun-Yi; Chang, Jhih-Ting; He, Cai-Ying; Cheng, Yi-Wen

2012-04-01

This study uses 3D virtual reality technology to create the "Mackay campus of the environmental education and digital cultural 3D navigation system" for local historical sites in the Tamsui (Hoba) area, in hopes of providing tourism information and navigation through historical sites using a 3D navigation system. We used Auto CAD, Sketch Up, and SpaceEyes 3D software to construct the virtual reality scenes and create the school's historical sites, such as the House of Reverends, the House of Maidens, the Residence of Mackay, and the Education Hall. We used this technology to complete the environmental education and digital cultural Mackay campus . The platform we established can indeed achieve the desired function of providing tourism information and historical site navigation. The interactive multimedia style and the presentation of the information will allow users to obtain a direct information response. In addition to showing the external appearances of buildings, the navigation platform can also allow users to enter the buildings to view lifelike scenes and textual information related to the historical sites. The historical sites are designed according to their actual size, which gives users a more realistic feel. In terms of the navigation route, the navigation system does not force users along a fixed route, but instead allows users to freely control the route they would like to take to view the historical sites on the platform.

Bell's "Theorem": loopholes vs. conceptual flaws

NASA Astrophysics Data System (ADS)

Kracklauer, A. F.

2017-12-01

An historical overview and detailed explication of a critical analysis of what has become known as Bell's Theorem to the effect that, it should be impossible to extend Quantum Theory with the addition of local, real variables so as to obtain a version free of the ambiguous and preternatural features of the currently accepted interpretations is presented. The central point on which this critical analysis, due originally to Edwin Jaynes, is that Bell incorrectly applied probabilistic formulas involving conditional probabilities. In addition, mathematical technicalities that have complicated the understanding of the logical or mathematical setting in which current theory and experimentation are embedded, are discussed. Finally, some historical speculations on the sociological environment, in particular misleading aspects, in which recent generations of physicists lived and worked are mentioned.

Satellite Monitoring of Boston Harbor Water Quality: Initial Investigations

NASA Astrophysics Data System (ADS)

Sheldon, P.; Chen, R. F.; Schaaf, C.; Pahlevan, N.; Lee, Z.

2016-02-01

The transformation of Boston Harbor from the "dirtiest in America" to a National Park Area is one of the most remarkable estuarine recoveries in the world. A long-term water quality dataset from 1991 to present exists in Boston Harbor due to a $3. 8 billion lawsuit requiring the harbor clean-up. This project uses discrete water sampling and underway transects with a towed vehicle coordinated with Landsat 7 and Landsat 8 to create surface maps of chlorophyll a (Chl a), dissolved organic matter (CDOM and DOC), total suspended solids (TSS), diffuse attenuation coefficient (Kd_490), and photic depth in Boston Harbor. In addition, 3 buoys have been designed, constructed, and deployed in Boston Harbor that measure Chl a and CDOM fluorescence, optical backscatter, salinity, temperature, and meteorological parameters. We are initially using summer and fall of 2015 to develop atmospheric corrections for conditions in Boston Harbor and develop algorithms for Landsat 8 data to estimate in water photic depth, TSS, Chl a, Kd_490, and CDOM. We will report on initial buoy and cruise data and show 2015 Landsat-derived distributions of water quality parameters. It is our hope that once algorithms for present Landsat imagery can be developed, historical maps of water quality can be constructed using in water data back to 1991.

Asking Questions: Will Army Tactical Interrogation be Ready for War?

DTIC Science & Technology

1986-12-17

still never answer the basic question: "Is there enough?" It is the interrogator portion of this question that this paper will address to provide a...tenative answer for the near to midrange future. Section II of this paper will examine the historical 2 AA 4 importance of interrogator derived...the former that this paper will concern itself. In addition to interrogators, there have historically existed, and there continue to exist today (almost

Demonstration-scale evaluation of a novel high-solids anaerobic digestion process for converting organic wastes to fuel gas and compost.

PubMed

Rivard, C J; Duff, B W; Dickow, J H; Wiles, C C; Nagle, N J; Gaddy, J L; Clausen, E C

1998-01-01

Early evaluations of the bioconversion potential for combined wastes such as tuna sludge and sorted municipal solid waste (MSW) were conducted at laboratory scale and compared conventional low-solids, stirred-tank anaerobic systems with the novel, high-solids anaerobic digester (HSAD) design. Enhanced feedstock conversion rates and yields were determined for the HSAD system. In addition, the HSAD system demonstrated superior resiliency to process failure. Utilizing relatively dry feedstocks, the HSAD system is approximately one-tenth the size of conventional low-solids systems. In addition, the HSAD system is capable of organic loading rates (OLRs) on the order of 20-25 g volatile solids per liter digester volume per d (gVS/L/d), roughly 4-5 times those of conventional systems. Current efforts involve developing a demonstration-scale (pilot-scale) HSAD system. A two-ton/d plant has been constructed in Stanton, CA and is currently in the commissioning/startup phase. The purposes of the project are to verify laboratory- and intermediate-scale process performance; test the performance of large-scale prototype mechanical systems; demonstrate the long-term reliability of the process; and generate the process and economic data required for the design, financing, and construction of full-scale commercial systems. This study presents conformational fermentation data obtained at intermediate-scale and a snapshot of the pilot-scale project.

Solid-support immobilization of a "swing" fusion protein for enhanced glucose oxidase catalytic activity.

PubMed

Takatsuji, Yoshiyuki; Yamasaki, Ryota; Iwanaga, Atsushi; Lienemann, Michael; Linder, Markus B; Haruyama, Tetsuya

2013-12-01

The strategic surface immobilization of a protein can add new functionality to a solid substrate; however, protein activity, e.g., enzymatic activity, can be drastically decreased on immobilization onto a solid surface. The concept of a designed and optimized "molecular interface" is herein introduced in order to address this problem. In this study, molecular interface was designed and constructed with the aim of attaining high enzymatic activity of a solid-surface-immobilized a using the hydrophobin HFBI protein in conjunction with a fusion protein of HFBI attached to glucose oxidase (GOx). The ability of HFBI to form a self-organized membrane on a solid surface in addition to its adhesion properties makes it an ideal candidate for immobilization. The developed fusion protein was also able to form an organized membrane, and its structure and immobilized state on a solid surface were investigated using QCM-D measurements. This method of immobilization showed retention of high enzymatic activity and the ability to control the density of the immobilized enzyme. In this study, we demonstrated the importance of the design and construction of molecular interface for numerous purposes. This method of protein immobilization could be utilized for preparation of high throughput products requiring structurally ordered molecular interfaces, in addition to many other applications. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Solid-state, ambient-operation thermally activated delayed fluorescence from flexible, non-toxic gold-nanocluster thin films: towards the development of biocompatible light-emitting devices

NASA Astrophysics Data System (ADS)

Talite, M. J. A.; Lin, H. T.; Jiang, Z. C.; Lin, T. N.; Huang, H. Y.; Heredia, E.; Flores, A.; Chao, Y. C.; Shen, J. L.; Lin, C. A. J.; Yuan, C. T.

2016-08-01

Luminescent gold nanoclusters (AuNCs) with good biocompatibility have gained much attention in bio-photonics. In addition, they also exhibit a unique photo-physical property, namely thermally activated delayed fluorescence (TADF), by which both singlet and triplet excitons can be harvested. The combination of their non-toxic material property and unique TADF behavior makes AuNCs biocompatible nano-emitters for bio-related light-emitting devices. Unfortunately, the TADF emission is quenched when colloidal AuNCs are transferred to solid states under ambient environment. Here, a facile, low-cost and effective method was used to generate efficient and stable TADF emissions from solid AuNCs under ambient environment using polyvinyl alcohol as a solid matrix. To unravel the underlying mechanism, temperature-dependent static and transient photoluminescence measurements were performed and we found that two factors are crucial for solid TADF emission: small energy splitting between singlet and triplet states and the stabilization of the triplet states. Solid TADF films were also deposited on the flexible plastic substrate with patterned structures, thus mitigating the waveguide-mode losses. In addition, we also demonstrated that warm white light can be generated based on a co-doped single emissive layer, consisting of non-toxic, solution-processed TADF AuNCs and fluorescent carbon dots under UV excitation.

An advanced model framework for solid electrolyte intercalation batteries.

PubMed

Landstorfer, Manuel; Funken, Stefan; Jacob, Timo

2011-07-28

Recent developments of solid electrolytes, especially lithium ion conductors, led to all solid state batteries for various applications. In addition, mathematical models sprout for different electrode materials and battery types, but are missing for solid electrolyte cells. We present a mathematical model for ion flux in solid electrolytes, based on non-equilibrium thermodynamics and functional derivatives. Intercalated ion diffusion within the electrodes is further considered, allowing the computation of the ion concentration at the electrode/electrolyte interface. A generalized Frumkin-Butler-Volmer equation describes the kinetics of (de-)intercalation reactions and is here extended to non-blocking electrodes. Using this approach, numerical simulations were carried out to investigate the space charge region at the interface. Finally, discharge simulations were performed to study different limitations of an all solid state battery cell. This journal is © the Owner Societies 2011

Modelling and evaluating municipal solid waste management strategies in a mega-city: the case of Ho Chi Minh City.

PubMed

ThiKimOanh, Le; Bloemhof-Ruwaard, Jacqueline M; van Buuren, Joost Cl; van der Vorst, Jack Gaj; Rulkens, Wim H

2015-04-01

Ho Chi Minh City is a large city that will become a mega-city in the near future. The city struggles with a rapidly increasing flow of municipal solid waste and a foreseeable scarcity of land to continue landfilling, the main treatment of municipal solid waste up to now. Therefore, additional municipal solid waste treatment technologies are needed. The objective of this article is to support decision-making towards more sustainable and cost-effective municipal solid waste strategies in developing countries, in particular Vietnam. A quantitative decision support model is developed to optimise the distribution of municipal solid waste from population areas to treatment plants, the treatment technologies and their capacities for the near future given available infrastructure and cost factors. © The Author(s) 2015.

Materials research for passive solar systems: Solid-state phase-change materials

NASA Astrophysics Data System (ADS)

Benson, D. K.; Webb, J. D.; Burrows, R. W.; McFadden, J. D. O.; Christensen, C.

1985-03-01

A set of solid-state phase-change materials is being evaluated for possible use in passive solar thermal energy storage systems. The most promising materials are organic solid solutions of pentaerythritol (C5H12O4), pentaglycerinve (C5H12O3), and neopentyl glycol (C5H12O2). Solid solution mixtures of these compounds can be tailored so that they exhibit solid-to-solid phase transformations at any desired temperature between 25 C and 188 C, and have latent heats of transformation etween 20 and 70 cal/g. Transformation temperatures, specific heats, and latent heats of transformation have been measured for a number of these materials. Limited cyclic experiments suggest that the solid solutions are stable. These phase-change materials exhibit large amounts of undercooling; however, the addition of certain nucleating agents as particulate dispersions in the solid phase-change material greatly reduces this effect. Computer simulations suggest that the use of an optimized solid-state phase-change material in a Trombe wall could provide better performance than a concrete Trombe wall four times thicker and nine times heavier.

Use of surfactants as plasticizers in preparing solid dispersions of poorly soluble API: stability testing of selected solid dispersions.

PubMed

Ghebremeskel, Alazar N; Vemavarapu, Chandra; Lodaya, Mayur

2006-08-01

The purpose of the study is to evaluate the effect of surfactant-plasticizers on the physical stability of amorphous drug in polymer matrices formed by hot melt extrusion. Solid dispersions of a poorly soluble drug were prepared using PVP-K30, Plasdone-S630, and HPMC-E5 as the polymeric carriers and surfactants as plasticizers. The solid dispersions were produced by hot melt extrusion at temperatures 10 degrees C above and below the glass transition temperature (Tg) of the carrier polymers using a 16 mm-Haake Extruder. The surfactants tested in this study included Tween-80 and Docusate Sodium. The particle size of the extrudate was reduced to have mean of 100-200 micron. The physical stability of the solid dispersions produced was monitored at 30 degrees C/60% for six-months and at 60 degrees C/85% for two-months in open HDPE bottles. Modulated differential scanning calorimetry, polarized light microscopy, powder X-ray diffraction and dissolution testing was performed to assess the physical stability of solid dispersions upon stress testing. The dispersions containing HPMC-E5 were observed especially to be susceptible to physical instability under an accelerated stress conditions (60 degrees C/85%RH) of the solid dispersion. About 6% conversion of amorphous drug to crystalline form was observed. Consequently, the system exhibits similar degree of re-crystallization upon addition of the surfactant. However, under 30 degrees C/60%RH condition, the otherwise amorphous Drug-HPMC-E5 system has been destabilized by the addition of the surfactant. This effect is much more reduced in the extruded solid dispersions where polymeric carriers such as Plasdone S-603 and PVP-K30 (in addition to surfactants) are present. Furthermore, the drug release from the solid dispersions was unaffected at the stress conditions reported above. Possible reasons for the enhanced stability of the dispersions are due to the surfactants ability to lower the viscosity of the melt, increase the API solubility and homogeneity in the carrier polymer. In contrast, while it is possible for the surfactants to destabilize the system by lowering the Tg and increasing the water uptake, the study confirms that this effect is minimal. By and large, the surfactants appear to be promising plasticizers to produce solid dispersions by hot melt extrusion, in so doing improving dissolution rate without compromising the physical stability of the systems.

Enhanced hot-carrier cooling and ultrafast spectral diffusion in strongly coupled PbSe quantum-dot solids.

PubMed

Gao, Yunan; Talgorn, Elise; Aerts, Michiel; Trinh, M Tuan; Schins, Juleon M; Houtepen, Arjan J; Siebbeles, Laurens D A

2011-12-14

PbSe quantum-dot solids are of great interest for low cost and efficient photodetectors and solar cells. We have prepared PbSe quantum-dot solids with high charge carrier mobilities using layer-by-layer dip-coating with 1,2-ethanediamine as substitute capping ligands. Here we present a time and energy resolved transient absorption spectroscopy study on the kinetics of photogenerated charge carriers, focusing on 0-5 ps after photoexcitation. We compare the observed carrier kinetics to those for quantum dots in dispersion and show that the intraband carrier cooling is significantly faster in quantum-dot solids. In addition we find that carriers diffuse from higher to lower energy sites in the quantum-dot solid within several picoseconds.

Dynamics of solid lubrication as observed by optical microscopy

NASA Technical Reports Server (NTRS)

Sliney, H. E.

1976-01-01

A bench metallograph was converted into a micro contact imager by the addition of a tribometer employing a steel ball in sliding contact with a glass disk. The sliding contact was viewed in real time by means of projection microscope optics. The dynamics of abrasive particles and of solid lubricant particles within the contact were observed in detail. The contact was characterized by a constantly changing pattern of elastic strain with the passage of surface discontinuities and solid particles. Abrasive particles fragmented upon entering the contact, embedded in one surface and scratched the other; in contrast, the solid lubricant particles flowed plastically into thin films. The rheological behavior of the lubricating solids gave every appearance of a paste-like consistency within the Hertzian contact.

The Soret Effect in Liquid Mixtures - A Review

NASA Astrophysics Data System (ADS)

Köhler, Werner; Morozov, Konstantin I.

2016-07-01

The Soret effect describes diffusive motion that originates from a temperature gradient. It is observed in mixtures of gases, liquids and even solids. Although there is a formal phenomenological description based on linear nonequilibrium thermodynamics, the Soret effect is a multicause phenomenon and there is no univocal microscopic picture. After a brief historical overview and an outline of the fundamental thermodynamic concepts, this review focuses on thermodiffusion in binary and ternary liquid mixtures. The most important experimental techniques used nowadays are introduced. Then, a modern development in studying thermal diffusion, the discovery of both integral and specific additivity laws, is discussed. The former relate to the general behavior of the substances in a temperature field according to their thermophobicities, which prove to be pure component properties. The thermophobicities allow for a convenient classification of the phenomenon, a simple interpretation and a proper estimation and prediction of the thermodiffusion parameters. The specific laws relate to the additivity of the particular contributions. Among the latter, we discuss the isotopic Soret effect and the so-called chemical contribution. From the theoretical side, there are kinetic and thermodynamic theories, and the nature of the driving forces of thermodiffusion can be either of volume or surface type. Besides analytical models, computer simulations become increasingly important. Polymer solutions are special as they represent highly asymmetric molecular systems with a molar mass-independent thermophoretic mobility. Its origin is still under debate, and draining and non-draining models are presently discussed. Finally, some discussion is devoted to ternary mixtures, which only recently have been investigated in more detail.

Discovering Volatile Chemicals from Window Weatherstripping through Solid-Phase Microextraction/Gas Chromatography-Mass Spectrometry

ERIC Educational Resources Information Center

Rosu, Cornelia; Cueto, Rafael; Veillion, Lucas; David, Connie; Laine, Roger A.; Russo, Paul S.

2017-01-01

Volatile compounds from polymeric materials such as weatherstripping were identified by solid-phase microextraction (SPME), a solvent-free analytical method, coupled to gas chromatography-mass spectrometry (GC-MS). These compounds, originating from additives and fillers used in weatherstripping processing, were mostly polycyclic aromatic…

An industrial application of the JPL ACTS with energy recovery

NASA Technical Reports Server (NTRS)

Humphrey, M. F.; Wilson, G. E.; Schroepfer, T. W.

1980-01-01

The JPL Activated Carbon Treatment System (ACTS) uses sewage solids derived from municipal wastewater treatment systems as a source of organic material for powdered activated carbons (PAC). The PAC is used for the COD removal from wastewater and as a filter aid in the recovery of additional sewage solids.

Multicenter phase II study of irinotecan, cisplatin, and bevacizumab in patients with metastatic gastric or gastroesophageal junction adenocarcinoma.

PubMed

Shah, Manish A; Ramanathan, Ramesh K; Ilson, David H; Levnor, Alissa; D'Adamo, David; O'Reilly, Eileen; Tse, Archie; Trocola, Robin; Schwartz, Lawrence; Capanu, Marinela; Schwartz, Gary K; Kelsen, David P

2006-11-20

Bevacizumab improves survival in several solid tumor malignancies when combined with chemotherapy. We evaluated the efficacy and safety of the addition of bevacizumab to chemotherapy in the treatment of gastric and gastroesophageal junction (GEJ) adenocarcinoma. Forty-seven patients with metastatic or unresectable gastric/GEJ adenocarcinoma were treated with bevacizumab 15 mg/kg on day 1, irinotecan 65 mg/m2, and cisplatin 30 mg/m2 on days 1 and 8, every 21 days. The primary end point was to demonstrate a 50% improvement in time to progression over historical values. Secondary end points included safety, response, and survival. Patient characteristics were as follows: median age 59 years (range, 25 to 75); Karnofsky performance status 90% (70% to 100%); male:female, 34:13; and gastric/GEJ, 24:23. With a median follow-up of 12.2 months, median time to progression was 8.3 months (95% CI, 5.5 to 9.9 months). In 34 patients with measurable disease, the overall response rate was 65% (95% CI, 46% to 80%). Median survival was 12.3 months (95% CI, 11.3 to 17.2 months). We observed no increase in chemotherapy related toxicity. Possible bevacizumab-related toxicity included a 28% incidence of grade 3 hypertension, two patients with a gastric perforation and one patient with a near perforation (6%), and one patient with a myocardial infarction (2%). Grade 3 to 4 thromboembolic events occurred in 25% of patients. Although the primary tumor was unresected in 40 patients, we observed only one patient with a significant upper gastrointestinal bleed. Bevacizumab can be safely given with chemotherapy even with primary gastric and GEJ tumors in place. The response rate, time to disease progression (TTP), and overall survival are encouraging, with TTP improved over historical controls by 75%. Further development of bevacizumab in gastric and GEJ cancers is warranted.

Experimental Analysis of Dynamic Effects of FRP Reinforced Masonry Vaults.

PubMed

Corradi, Marco; Borri, Antonio; Castori, Giulio; Coventry, Kathryn

2015-11-27

An increasing interest in the preservation of historic structures has produced a need for new methods for reinforcing curved masonry structures, such as arches and vaults. These structures are generally very ancient, have geometries and materials which are poorly defined and have been exposed to long-term historical movements and actions. Consequently, they are often in need of repair or reinforcement. This article presents the results of an experimental study carried out in the laboratory and during on-site testing to investigate the behaviour of brick masonry vaults under dynamic loading strengthened with FRPs (Fiber Reinforced Polymers). For the laboratory tests, the brick vaults were built with solid sanded clay bricks and weak mortar and were tested under dynamic loading. The experimental tests were designed to facilitate analysis of the dynamic behaviour of undamaged, damaged and reinforced vaulted structures. On-site tests were carried out on an earthquake-damaged thin brick vault of an 18th century aristocratic residence in the city of L'Aquila, Italy. The provision of FRP reinforcement is shown to re-establish elastic behavior previously compromised by time induced damage in the vaults.

Experimental Analysis of Dynamic Effects of FRP Reinforced Masonry Vaults

PubMed Central

Corradi, Marco; Borri, Antonio; Castori, Giulio; Coventry, Kathryn

2015-01-01

An increasing interest in the preservation of historic structures has produced a need for new methods for reinforcing curved masonry structures, such as arches and vaults. These structures are generally very ancient, have geometries and materials which are poorly defined and have been exposed to long-term historical movements and actions. Consequently, they are often in need of repair or reinforcement. This article presents the results of an experimental study carried out in the laboratory and during on-site testing to investigate the behaviour of brick masonry vaults under dynamic loading strengthened with FRPs (Fiber Reinforced Polymers). For the laboratory tests, the brick vaults were built with solid sanded clay bricks and weak mortar and were tested under dynamic loading. The experimental tests were designed to facilitate analysis of the dynamic behaviour of undamaged, damaged and reinforced vaulted structures. On-site tests were carried out on an earthquake-damaged thin brick vault of an 18th century aristocratic residence in the city of L’Aquila, Italy. The provision of FRP reinforcement is shown to re-establish elastic behavior previously compromised by time induced damage in the vaults. PMID:28793697

From Laser Scanning to Finite Element Analysis of Complex Buildings by Using a Semi-Automatic Procedure.

PubMed

Castellazzi, Giovanni; D'Altri, Antonio Maria; Bitelli, Gabriele; Selvaggi, Ilenia; Lambertini, Alessandro

2015-07-28

In this paper, a new semi-automatic procedure to transform three-dimensional point clouds of complex objects to three-dimensional finite element models is presented and validated. The procedure conceives of the point cloud as a stacking of point sections. The complexity of the clouds is arbitrary, since the procedure is designed for terrestrial laser scanner surveys applied to buildings with irregular geometry, such as historical buildings. The procedure aims at solving the problems connected to the generation of finite element models of these complex structures by constructing a fine discretized geometry with a reduced amount of time and ready to be used with structural analysis. If the starting clouds represent the inner and outer surfaces of the structure, the resulting finite element model will accurately capture the whole three-dimensional structure, producing a complex solid made by voxel elements. A comparison analysis with a CAD-based model is carried out on a historical building damaged by a seismic event. The results indicate that the proposed procedure is effective and obtains comparable models in a shorter time, with an increased level of automation.

Ares I Stage Separation System Design Certification Testing

NASA Technical Reports Server (NTRS)

Mayers, Stephen L.; Beard, Bernard B.; Smith, R. Kenneth; Patterson, Alan

2009-01-01

NASA is committed to the development of a new crew launch vehicle, the Ares I, that can support human missions to low Earth orbit (LEO) and the moon with unprecedented safety and reliability. NASA's Constellation program comprises the Ares I and Ares V launch vehicles, the Orion crew vehicle, and the Altair lunar lander. Based on historical precedent, stage separation is one of the most significant technical and systems engineering challenges that must be addressed in order to achieve this commitment. This paper surveys historical separation system tests that have been completed in order to ensure staging of other launch vehicles. Key separation system design trades evaluated for Ares I include single vs. dual separation plane options, retro-rockets vs. pneumatic gas actuators, small solid motor quantity/placement/timing, and continuous vs. clamshell interstage configuration options. Both subscale and full-scale tests are required to address the prediction of complex dynamic loading scenarios present during staging events. Test objectives such as separation system functionality, and pyroshock and debris field measurements for the full-scale tests are described. Discussion about the test article, support infrastructure and instrumentation are provided.

NEUTRALIZATIONS OF HIGH ALUMINUM LOW URANIUM USED NUCLEAR FUEL SOLUTIONS CONTAINING GADOLINIUM AS A NEUTRON POISON

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor-Pashow, K.

2011-06-08

H-Canyon will begin dissolving High Aluminum - Low Uranium (High Al/Low U) Used Nuclear Fuel (UNF) following approval by DOE which is anticipated in CY2011. High Al/Low U is an aluminum/enriched uranium UNF with small quantities of uranium relative to aluminum. The maximum enrichment level expected is 93% {sup 235}U. The High Al/Low U UNF will be dissolved in H-Canyon in a nitric acid/mercury/gadolinium solution. The resulting solution will be neutralized and transferred to Tank 39H in the Tank Farm. To confirm that the solution generated could be poisoned with Gd, neutralized, and discarded to the Savannah River Site (SRS)more » high level waste (HLW) system without undue nuclear safety concerns the caustic precipitation of simulant solutions was examined. Experiments were performed with three simulant solutions representative of the H-Canyon estimated concentrations in the final solutions after dissolution. The maximum U, Gd, and Al concentration were selected for testing from the range of solution compositions provided. Simulants were prepared in three different nitric acid concentrations, ranging from 0.5 to 1.5 M. The simulant solutions were neutralized to four different endpoints: (1) just before a solid phase was formed (pH 3.5-4), (2) the point where a solid phase was obtained, (3) 0.8 M free hydroxide, and (4) 1.2 M free hydroxide, using 50 wt % sodium hydroxide (NaOH). The settling behavior of the neutralized solutions was found to be slower compared to previous studies, with settling continuing over a one week period. Due to the high concentration of Al in these solutions, precipitation of solids was observed immediately upon addition of NaOH. Precipitation continued as additional NaOH was added, reaching a point where the mixture becomes almost completely solid due to the large amount of precipitate. As additional NaOH was added, some of the precipitate began to redissolve, and the solutions neutralized to the final two endpoints mixed easily and had expected densities of typical neutralized waste. Based on particle size and scanning electron microscopy analyses, the neutralized solids were found to be homogeneous and less than 20 microns in size. The majority of solids were less than 4 microns in size. Compared to previous studies, a larger percentage of the Gd was found to precipitate in the partially neutralized solutions (at pH 3.5-4). In addition the Gd:U mass ratio was found to be at least 1.0 in all of the solids obtained after partial or full neutralization. The hydrogen to U (H:U) molar ratios for two accident scenarios were also determined. The first was for transient neutralization and agitator failure. Experimentally this scenario was determined by measuring the H:U ratio of the settled solids. The minimum H:U molar ratio for solids from fully neutralized solutions was 388:1. The second accident scenario is for the solids drying out in an unagitiated pump box. Experimentally, this scenario was determined by measuring the H:U molar ratio in centrifuged solids. The minimum H:U atom ratios for centrifuged precipitated solids was 250:1. It was determined previously that a 30:1 H:Pu atom ratio was sufficient for a 1:1 Gd:Pu mass ratio. Assuming a 1:1 equivalence with {sup 239}Pu, the results of these experiments show Gd is a viable poison for neutralizing U/Gd solutions with the tested compositions.« less

Characterization of Resistance to Cephus cinctus (Hymenoptera: Cephidae) in Barley Germplasm.

PubMed

Varella, Andrea C; Talbert, Luther E; Achhami, Buddhi B; Blake, Nancy K; Hofland, Megan L; Sherman, Jamie D; Lamb, Peggy F; Reddy, Gadi V P; Weaver, David K

2018-04-02

Most barley cultivars have some degree of resistance to the wheat stem sawfly (WSS), Cephus cinctus Norton (Hymenoptera: Cephidae). Damage caused by WSS is currently observed in fields of barley grown in the Northern Great Plains, but the impact of WSS damage among cultivars due to genetic differences within the barley germplasm is not known. Specifically, little is known about the mechanisms underlying WSS resistance in barley. We characterized WSS resistance in a subset of the spring barley CAP (Coordinated Agricultural Project) germplasm panel containing 193 current and historically important breeding lines from six North American breeding programs. Panel lines were grown in WSS infested fields for two consecutive years. Lines were characterized for stem solidness, stem cutting, WSS infestation (antixenosis), larval mortality (antibiosis), and parasitism (indirect plant defense). Variation in resistance to WSS in barley was compared to observations made for solid-stemmed resistant and hollow-stemmed susceptible wheat lines. Results indicate that both antibiosis and antixenosis are involved in the resistance of barley to the WSS, but antibiosis seems to be more prevalent. Almost all of the barley lines had greater larval mortality than the hollow-stemmed wheat lines, and only a few barley lines had mortality as low as that observed in the solid-stemmed wheat line. Since barley lines lack solid stems, it is apparent that barley has a different form of antibiosis. Our results provide information for use of barley in rotation to control the WSS and may provide a basis for identification of new approaches for improving WSS resistance in wheat.

Measuring past glacier fluctuations from historic photographs geolocated using Structure from Motion

NASA Astrophysics Data System (ADS)

Vargo, L.; Anderson, B.; Horgan, H. J.; Mackintosh, A.; Lorrey, A.; Thornton, M.

2017-12-01

Quantifying glacier fluctuations is important for understanding how the cryosphere responds to climate variability and change. Photographs of past ice extents have become iconic images of climate change, but until now incorporating these images into quantitative estimates of glacier change has been problematic. We present a new method to quantitatively measure past glacier fluctuations from historic images. The method uses a large set of modern geolocated photographs and Structure from Motion (SfM) to calculate the camera parameters for the historic images, including the location from which they were taken. We initially apply this method to a small maritime New Zealand glacier (Brewster Glacier, 44°S, 2 km2), and quantify annual equilibrium line altitudes (ELAs) and length changes from historic oblique aerial photographs (1981 - 2017). Results show that Brewster has retreated 364 ± 12 m since 1981 and, using independent field measurements of terminus positions (2005 - 2014), we show that this SfM-derived length record accurately captures glacier change. We calculate the uncertainties associated with this method using known coordinates of bedrock features surrounding the glacier. Mean uncertainties in the ELA and length records are 7 m and 11 m, respectively. In addition to Brewster, 49 other New Zealand glaciers have been monitored by aerial photographs since 1978. However, the length records for these glaciers only include years of relative advance or retreat, and no length changes have been quantified. We will ultimately apply this method to all 50 glaciers, expanding the database of New Zealand glacier fluctuations that until now included only a few glaciers. This method can be further applied to any glacier with historic images, and can be used to measure past changes in glacier width, area, and surface elevation in addition to ELA and length.

Examining differences between recovered and declining endangered species

USGS Publications Warehouse

Abbitt, Robbyn J.F.; Scott, J. Michael

2001-01-01

Between 1973 and 1999, 43 species in the United States were reclassified from endangered to threatened or removed entirely from the Endangered Species List. Of these, 23 were identified as recovered. In 1999 the U.S. Fish and Wildlife Service ( USFWS) published a list of 33 additional species for possible reclassification and/or delisting. We initiated this study to examine why some endangered species recover but others continue to decline and to identify differences in management activities between these two groups. We defined recovered/recovering species as previously recovered species and the additional recovered/recovering species listed by the USFWS. We defined declining species as those identified as declining in the most recent USFWS Report to Congress. Information on recovered/recovering and declining species was gathered from relevant literature, recovery plans, U.S. Federal Register documents, and individuals responsible for the recovery management of each species. We used this information to examine (1) the percentage of current and historic range covered by management activities; (2) threats affecting the species; (3) population sizes at the time of listing; (4) current versus historic range size; and (5) percentage of recovery management objectives completed. Although few statistical analyses provided significant results, those that did suggest the following differences between recovered/recovering and declining species: (1) recovered/recovering species face threats that are easier to address; (2) recovered/recovering species occupy a greater percentage of their historic range; and (3) recovered/recovering species have a greater percentage of their recovery management objectives completed. Those species with threats easier to address and that occupy a greater percentage of their historic range are recovered/recovering. In contrast, declining species face threats more difficult to address and occupy significantly less of their historic range. If this remains true, future species recovery may require more time and resources.

Supercritical fluid precipitation of ketoprofen in novel structured lipid carriers for enhanced mucosal delivery--a comparison with solid lipid particles.

PubMed

Gonçalves, V S S; Matias, A A; Rodríguez-Rojo, S; Nogueira, I D; Duarte, C M M

2015-11-10

Structured lipid carriers based on mixture of solid lipids with liquid lipids are the second generation of solid lipid particles, offering the advantage of improved drug loading capacity and higher storage stability. In this study, structured lipid carriers were successfully prepared for the first time by precipitation from gas saturated solutions. Glyceryl monooleate (GMO), a liquid glycerolipid, was selected in this work to be incorporated into three solid glycerolipids with hydrophilic-lipophilic balance (HLB) ranging from 1 to 13, namely Gelucire 43/01™, Geleol™ and Gelucire 50/13™. In general, microparticles with a irregular porous morphology and a wide particle size distribution were obtained. The HLB of the individual glycerolipids might be a relevant parameter to take into account during the processing of solid:liquid lipid blends. As expected, the addition of a liquid lipid into a solid lipid matrix led to increased stability of the lipid carriers, with no significant modifications in their melting enthalpy after 6 months of storage. Additionally, Gelucire 43/01™:GMO particles were produced with different mass ratios and loaded with ketoprofen. The drug loading capacity of the structured lipid carriers increased as the GMO content in the particles increased, achieving a maximum encapsulation efficiency of 97% for the 3:1 mass ratio. Moreover, structured lipid carriers presented an immediate release of ketoprofen from its matrix with higher permeation through a mucous-membrane model, while solid lipid particles present a controlled release of the drug with less permeation capacity. Copyright © 2015. Published by Elsevier B.V.

Bacterial toxicity assessment of drinking water treatment residue (DWTR) and lake sediment amended with DWTR.

PubMed

Yuan, Nannan; Wang, Changhui; Pei, Yuansheng

2016-11-01

Drinking water treatment residue (DWTR) seems to be very promising for controlling lake sediment pollution. Logically, acquisition of the potential toxicity of DWTR will be beneficial for its applications. In this study, the toxicity of DWTR and sediments amended with DWTR to Aliivibrio fischeri was evaluated based on the Microtox(®) solid and leachate phase assays, in combination with flow cytometry analyses and the kinetic luminescent bacteria test. The results showed that both solid particles and aqueous/organic extracts of DWTR exhibited no toxicity to the bacterial luminescence and growth. The solid particles of DWTR even promoted bacterial luminescence, possibly because DWTR particles could act as a microbial carrier and provide nutrients for bacteria growth. Bacterial toxicity (either luminescence or growth) was observed from the solid phase and aqueous/organic extracts of sediments with or without DWTR addition. Further analysis showed that the solid phase toxicity was determined to be related mainly to the fixation of bacteria to fine particles and/or organic matter, and all of the observed inhibition resulting from aqueous/organic extracts was identified as non-significant. Moreover, DWTR addition not only had no adverse effect on the aqueous/organic extract toxicity of the sediment but also reduced the solid phase toxicity of the sediment. Overall, in practical application, the solid particles, the water-soluble substances transferred to surface water or the organic substances in DWTR had no toxicity or any delayed effect on bacteria in lakes, and DWTR can therefore be considered as a non-hazardous material. Copyright © 2016 Elsevier Ltd. All rights reserved.

Balancing between two goods: Health Insurance Portability and Accountability Act and ethical compliancy considerations for privacy-sensitive materials in health sciences archival and historical special collections.

PubMed

Wiener, Judith A; Gilliland, Anne T

2011-01-01

The investigation provides recommendations for establishing institutional collection guidelines and policies that protect the integrity of the historical record, while upholding the privacy and confidentiality of those who are protected by Health Insurance Portability and Accountability Act (HIPAA) or professional ethical standards. The authors completed a systematic historical investigation of the concepts of collection integrity, privacy, and confidentiality in the formal and informal legal and professional ethics literature and applied these standards to create best practices for institutional policies in these areas. Through an in-depth examination of the historical concepts of privacy and confidentiality in the legal and professional ethics literature, the authors were able to create recommendations that would allow institutions to provide access to important, yet sensitive, materials, while complying with the standards set by HIPAA regulations and professional ethical expectations. With thoughtful planning, it is possible to balance the integrity of and access to the historical record of sensitive documents, while supporting the privacy protections of HIPAA and professional ethical standards. Although it is theorized that collection development policies of institutions have changed due to HIPAA legislation, additional research is suggested to see how various legal interpretations have affected the integrity of the historical record in actuality.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Miao; Mohammadi, Reza; Turner, Christopher L.

In this paper, we explore the hardening mechanisms in WB4-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under nonhydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB 4 solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Miao; Turner, Christopher L.; Mohammadi, Reza

In this work, we explore the hardening mechanisms in WB{sub 4}-based solid solutions upon addition of Ta, Mn, and Cr using in situ radial X-ray diffraction techniques under non-hydrostatic pressure. By examining the lattice-supported differential strain, we provide insights into the mechanism for hardness increase in binary solid solutions at low dopant concentrations. Speculations on the combined effects of electronic structure and atomic size in ternary WB{sub 4} solid solutions containing Ta with Mn or Cr are also included to understand the extremely high hardness of these materials.

Method of production of pure hydrogen near room temperature from aluminum-based hydride materials

DOEpatents

Pecharsky, Vitalij K.; Balema, Viktor P.

2004-08-10

The present invention provides a cost-effective method of producing pure hydrogen gas from hydride-based solid materials. The hydride-based solid material is mechanically processed in the presence of a catalyst to obtain pure gaseous hydrogen. Unlike previous methods, hydrogen may be obtained from the solid material without heating, and without the addition of a solvent during processing. The described method of hydrogen production is useful for energy conversion and production technologies that consume pure gaseous hydrogen as a fuel.

Application of the endochronic theory of viscoplasticity to solid propellants and sandasphalt concrete

NASA Technical Reports Server (NTRS)

Peng, S. T. J.; Valanis, K. C.

1977-01-01

Solid propellants, sand-asphalt concrete and hard plastics showed rate sensitive mechanical behavior which, in addition, indicated that these materials have a permanent memory of the strain (or loading) path by which their present state was attained. A constitutive equation was formulated in general three dimensional tensorial form by means of irreversible thermodynamics. By using a very simple analytical form, it was shown that the mechanical behavior of solid propellants and sand-asphalt concrete can be readily described.

South Australian historical earthquakes in the pre-instrumental period 1837-1963: A comprehensive chronicle and analysis of available intensity data

NASA Astrophysics Data System (ADS)

Dix, Katherine; Greenhalgh, Stewart

2014-05-01

Macroseismic data in the form of felt reports of earthquake shaking is vital to seismic hazard assessment, especially in view of the relatively short period of instrumental recording in many countries. During the early 1990s, we conducted a very detailed examination of historical earthquake records held in the State Government archives and the Public Library (newspaper accounts) of South Australia. This work resulted in the compilation of a list of just over 460 earthquakes in the period prior to seismic network recording, which commenced in 1963. A single Milne (and later Milne-Shaw) seismograph had been operated in Adelaide from 1908 to 1948 to record worldwide events but it was not suitable for studying local seismic activity. The majority of the historical events uncovered had escaped mention in any previous publications on South Australian seismicity and seismic risk. This historical earthquake research, including the production of a large number of isoseismal maps to enable quantification in terms of magnitude and location, appears to have been the only study of its kind in South Australia performed so comprehensively, and resulted in the most extensive list available. After 20 years, it still stands as the definitive list of historical earthquake events in the State. The incorporation of these additional historical events into the South Australian Earthquake Catalogue maintained by the SA Department of Primary Industries and Resources had the potential to raise the previous listing of just 49 pre-instrumental events to 511 earthquakes, and to extend the record back another 46 years to 1837, the date the colony of South Australia was proclaimed. Some of the major events have been formally included in the South Australian Earthquake Catalogue. However, for many events there was insufficient information and/or time to finalize the source parameters due to the onerous task of manually trawling through historical records and newspapers for felt reports. With the advent of the information age, researching historical newspapers and records is now a feasible undertaking, although such accounts are biased by the population distribution and the history of newspaper operations in the emerging colony. To provide an example of what is possible, we recovered reports of an additional 110 previously unrecognized earthquakes during the first 50 years since European settlement of South Australia, from digitized SA newspapers recently made available on the National Library of Australia's website called TROVE. This was done in a relatively short period of time and now the South Australian Historical Earthquake List incorporating these events comprises some 679 entries. This research builds upon and consolidates the work that was commenced 20 years ago. By doing so, it proposes the establishment of flexible and convenient computerized processes to maintain well into the future an increasingly accurate and complete record of historical earthquakes in South Australia. This work may also provide a model for the ongoing development of historical earthquake records in other states and territories of Australia.

Electrochemical slurry compositions and methods for preparing the same

DOEpatents

Doherty, Tristan; Limthongkul, Pimpa; Butros, Asli; Duduta, Mihai; Cross, III, James C.

2016-11-01

Embodiments described herein generally relate to semi-solid suspensions, and more particularly to systems and methods for preparing semi-solid suspensions for use as electrodes in electrochemical devices such as, for example batteries. In some embodiments, a method for preparing a semi-solid electrode includes combining a quantity of an active material with a quantity of an electrolyte to form an intermediate material. The intermediate material is then combined with a conductive additive to form an electrode material. The electrode material is mixed to form a suspension having a mixing index of at least about 0.80 and is then formed into a semi-solid electrode.

Ultra-directional source of longitudinal acoustic waves based on a two-dimensional solid/solid phononic crystal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morvan, B.; Tinel, A.; Sainidou, R.

2014-12-07

Phononic crystals (PC) can be used to control the dispersion properties of acoustic waves, which are essential to direct their propagation. We use a PC-based two-dimensional solid/solid composite to demonstrate experimentally and theoretically the spatial filtering of a monochromatic non-directional wave source and its emission in a surrounding water medium as an ultra-directional beam with narrow angular distribution. The phenomenon relies on square-shaped equifrequency contours (EFC) enabling self-collimation of acoustic waves within the phononic crystal. Additionally, the angular width of collimated beams is controlled via the EFC size-shrinking when increasing frequency.

[Formulation and special investigations of innovative intraoral solid dosage forms.

PubMed

Kristo, K; kATONA, B; Piukovics, P; Olah, I; Sipos, B; Sipos, S E; Sovany, T; Hodi, K; Ifi Regdon, G

During our work, we summarized the types of solid dosage forms which were in the focus of attention in the last years because of their innovative pharmaceutical technology solution and simple use. The biopharmaceutics of solid dosage forms for intraoral use and the advantages of the use of these dosages forms were presented in general. However, these dosage forms cannot always be prepared with conventional pharmaceutical processes, therefore the special pharmaceutical solutions which can be applied for their preparation were presented. In addition to testing the European Pharmacopoeia dosage forms, the special tests which can be applied for the characterization of innovative solid dosage forms were highlighted.

Damage monitoring in historical murals by speckle interferometry

NASA Astrophysics Data System (ADS)

Hinsch, Klaus D.; Gulker, Gerd; Joost, Holger

2003-11-01

In the conservation of historical murals it is important to identify loose plaster sections that threaten to fall off. Electronic speckle interferometry in combination with acoustic excitation of the object has been employed to monitor loose areas. To avoid disadvantages of high sound irradiation of the complete building a novel directional audio-sound source based on nonlinear mixing of ultrasound has been introduced. The optical system was revised for optimum performance in the new environment. Emphasis is placed on noise suppression to increase sensitivity. Furthermore, amplitude and phase data of object response over the frequency-range inspected are employed to gain additional information on the state of the plaster or paint. Laboratory studies on sample specimen supplement field campaigns at historical sites.

Some historical relationships between science and technology with implications for behavior analysis

PubMed Central

Moxley, Roy A.

1989-01-01

The relationship between science and technology is examined in terms of some implications for behavior analysis. Problems result when this relationship is seen as one in which science generally begets technology in a one-way, or hierarchical, relationship. These problems are not found when the relationship between science and technology is seen as two-way, or symmetrical, within a larger context of relationships. Some historical examples are presented. Collectively, these and other examples in the references weaken the case for a prevailing one-way, hierarchical relationship and strengthen the case for a two-way, symmetrical relationship. In addition to being more accurate historically, the symmetrical relationship is also more consistent with the principles of behavior analysis. PMID:22478016

Stories, skulls, and colonial collections.

PubMed

Roque, Ricardo

2011-01-01

The essay explores the hypothesis of colonial collecting processes involving the active addition of the colonial context and historical past to museum objects through the production of short stories. It examines the emergent historicity of collections through a focus on the "histories" that museum workers and colonial agents have been attaching to scientific collections of human skulls. Drawing on the notions of collection trajectory and historiographical work, it offers an alternative perspective from which to approach the creation of singular histories and individual archives for objects in collections.

Research in NASA history: A guide to the NASA history program

NASA Technical Reports Server (NTRS)

1992-01-01

This report describes the research opportunities and accomplishments of NASA's agency wide history program. It also offers a concise guide to the historical documentary resources available at NASA Headquarters in Washington D.C., at NASA facilities located around the country, and through the federal records system. In addition, this report contains expanded contributions by Lee D. Saegessor and other members of the NASA Headquarters History Division and by those responsible for historical documents and records at some NASA centers.

2013 mask industry survey

NASA Astrophysics Data System (ADS)

Malloy, Matt

2013-09-01

A comprehensive survey was sent to merchant and captive mask shops to gather information about the mask industry as an objective assessment of its overall condition. 2013 marks the 12th consecutive year for this process. Historical topics including general mask profile, mask processing, data and write time, yield and yield loss, delivery times, maintenance, and returns were included and new topics were added. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the mask industry. While each year's survey includes minor updates based on feedback from past years and the need to collect additional data on key topics, the bulk of the survey and reporting structure have remained relatively constant. A series of improvements is being phased in beginning in 2013 to add value to a wider audience, while at the same time retaining the historical content required for trend analyses of the traditional metrics. Additions in 2013 include topics such as top challenges, future concerns, and additional details in key aspects of mask masking, such as the number of masks per mask set per ground rule, minimum mask resolution shipped, and yield by ground rule. These expansions beyond the historical topics are aimed at identifying common issues, gaps, and needs. They will also provide a better understanding of real-life mask requirements and capabilities for comparison to the International Technology Roadmap for Semiconductors (ITRS).

Role of fluttering dislocations in the thermal interface resistance between a silicon crystal and plastic solid 4He

NASA Astrophysics Data System (ADS)

Amrit, Jay; Ramiere, Aymeric; Volz, Sebastian

2018-01-01

A quantum solid (solid 4He) in contact with a classical solid defines a new class of interfaces. In addition to its quantum nature, solid 4He is indeed a very plastic medium. We examine the thermal interface resistance upon solidification of superfluid 4He in contact with a silicon crystal surface (111) and show that dislocations play a crucial role in the thermal interface transport. The growth of solid 4He and the measurements are conducted at the minimum of the melting curve of helium (0.778 K and ˜25 bar ). The results display a first-order transition in the Kapitza resistance from a value of RK ,L=(80 ±8 ) c m2K /W at a pressure of 24.5 bar to a value of RK ,S=(41.7 ±8 ) c m2K /W after the formation of solid helium at ˜25.2 bar . The drop in RK ,S is only of a factor of ˜2 , although transverse phonon modes in solid 4He now participate in heat transmission at the interface. We provide an explanation for the measured RK ,S by considering the interaction of thermal phonons with vibrating dislocations in solid 4He. We demonstrate that this mechanism, also called fluttering, induces a thermal resistance RF l∝NdT-6 , where T is the temperature and Nd is the density of dislocations. We estimate that for dislocation densities on the order of ˜107c m-2 , RF l predominates over the boundary resistance RK ,S. These fundamental findings shed light on the role of dislocations and provide a quantitative explanation for previous experiments which showed no measurable change in the Kapitza resistance between Cu and superfluid 4He upon solidification of the latter. This demonstrates the possibility of using dislocations as an additional means to tailor thermal resistances at interfaces, formed especially with a plastic material.

Demonstration of a Cylinder Fill System Based on Solid Electrolyte Oxygen Separator (SEOS) Technology: Early Field Assessment at a USAF Maintenance Facility

DTIC Science & Technology

2010-06-01

to result in lower maintenance and higher reliability compared with the commercially practiced options of pressure swing adsorption (PSA) or vacuum ...screen and the temperature displayed on the graph will decrease. The Knob is used to zoom the chart and scroll through historical values. For a list of...Friday ‐ Status: OK.  Tinker AFB reported a FAL alarm occurs when the compressor isn’t  pumping  oxygen.  The FAL  alarm terminates when the

Microgravity research in NASA ground-based facilities

NASA Technical Reports Server (NTRS)

Lekan, Jack

1989-01-01

An overview of reduced gravity research performed in NASA ground-based facilities sponsored by the Microgravity Science and Applications Program of the NASA Office of Space Science and Applications is presented. A brief description and summary of the operations and capabilities of each of these facilities along with an overview of the historical usage of them is included. The goals and program elements of the Microgravity Science and Applications programs are described and the specific programs that utilize the low gravity facilities are identified. Results from two particular investigations in combustion (flame spread over solid fuels) and fluid physics (gas-liquid flows at microgravity conditions) are presented.

Cryopreservation by vitrification: a promising approach for transplant organ banking.

PubMed

Finger, Erik B; Bischof, John C

2018-06-01

The objective of this review is to describe the physical and biological barriers to organ cryopreservation, historic approaches for conventional cryopreservation and evolving techniques for ice-free cryopreservation by vitrification. Vitrification is a process whereby a biologic substance is cooled to cryogenic temperatures without the destructive phase transition of liquid to solid ice. Recent advances in cryoprotective solutions, organ perfusion techniques and novel heating technologies have demonstrated the potential for vitrification and rewarming organs on a scale applicable for human transplantation. Successful strategies for organ cryopreservation could enable organ banking, which would recast the entire process in which organs are recovered, allocated, stored and prepared for transplant.

Liver and Kidney Transplantation: A Half-Century Historical Perspective.

PubMed

Sass, David A; Doyle, Alden M

2016-05-01

This article describes the evolution of solid organ kidney and liver transplantation and expounds on the challenges and successes that the early transplant researchers and clinicians encountered. The article highlights the surgical pioneers, delves into the milestones of enhanced immunosuppression protocols, discusses key federal legislative and policy changes, and expounds on the ongoing disparities of organ supply and demand and the need for extended criteria and live donor organs to combat these shortages. Finally, recent changes in organ allocation and distribution policies are discussed. The authors also spotlight novel interventions that will further revolutionize abdominal transplantation in the next 50 years. Copyright © 2016 Elsevier Inc. All rights reserved.

An Investigation into the Polymorphism and Crystallization of Levetiracetam and the Stability of its Solid Form.

PubMed

Xu, Kailin; Xiong, Xinnuo; Guo, Liuqi; Wang, Lili; Li, Shanshan; Tang, Peixiao; Yan, Jin; Wu, Di; Li, Hui

2015-12-01

Levetiracetam (LEV) crystals were prepared using different solvents at different temperatures. The LEV crystals were systematically characterized by X-ray powder diffraction (XRPD) and morphological analysis. The results indicated that many kinds of crystal habits exist in a solid form of LEV. To investigate the effects of LEV concentration, crystallization temperature, and crystallization type on crystallization and solid phase transformation of LEV, multiple methods were performed for LEV aqueous solution to determine if a new solid form exists in solid-state LEV. However, XRPD data demonstrate that the LEV solid forms possess same spatial arrangements that are similar to the original solid form. This result indicates that the LEV concentration, crystallization temperature, and crystallization type in aqueous solution have no influence on the crystallization and solid phase transformation of LEV. Moreover, crystallization by sublimation, melt cooling, and quench cooling, as well as mechanical effect, did not result in the formation of new LEV solid state. During melt cooling, the transformation of solid form LEV is a direct process from melting amorphous phase to the original LEV crystal phase, and the conversion rate is very quick. In addition, stability investigation manifested that LEV solid state is very stable under various conditions. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Enhancing the bioavailability of magnolol in rabbits using melting solid dispersion with polyvinylpyrrolidone.

PubMed

Lin, Shiuan-Pey; Hou, Yu-Chi; Liao, Tzu-Yun; Tsai, Shang-Yuan

2014-03-01

Preparation of magnolol-loaded amorphous solid dispersion was investigated for improving the bioavailability. A solid dispersion of magnolol was prepared with polyvinylpyrrolidone K-30 (PVP) by melting method, and the physical properties were characterized by using differential scanning calorimetry, powder X-ray diffractometry, Fourier transformation-infrared spectroscopy and scanning electron microscope. In addition, dissolution test was also performed. Subsequently, the bioavailability of magnolol pure compound, its physical mixture and solid dispersion were compared in rabbits. The blood samples withdrawn via marginal ear vein at specific time points were assayed by HPLC method. Oral administration of the solid dispersion of magnolol with PVP significantly increased the systemic exposures of magnolol and magnolol sulfates/glucuronides by 80.1% and 142.8%, respectively, compared to those given with magnolol pure compound. Magnolol-loaded amorphous solid dispersion with PVP has demonstrated enhanced bioavailability of magnolol in rabbits.

On the Lennard-Jones and Devonshire theory for solid state thermodynamics

NASA Astrophysics Data System (ADS)

Lustig, Rolf

2017-06-01

The Lennard-Jones and Devonshire theory is developed into a self-consistent scheme for essentially complete thermodynamic information. The resulting methodology is compared with molecular simulation of the Lennard-Jones system in the face-centred-cubic solid state over an excessive range of state points. The thermal and caloric equations of state are in almost perfect agreement along the entire fluid-solid coexistence lines over more than six orders of magnitude in pressure. For homogeneous densities greater than twice the solid triple point density, the theory is essentially exact for derivatives of the Helmholtz energy. However, the fluid-solid phase equilibria are in disagreement with simulation. It is shown that the theory is in error by an additive constant to the Helmholtz energy A/(NkBT). Empirical inclusion of the error term makes all fluid-solid equilibria indistinguishable from exact results. Some arguments about the origin of the error are given.

Modeling solid-state transformations occurring in dissolution testing.

PubMed

Laaksonen, Timo; Aaltonen, Jaakko

2013-04-15

Changes in the solid-state form can occur during dissolution testing of drugs. This can often complicate interpretation of results. Additionally, there can be several mechanisms through which such a change proceeds, e.g. solvent-mediated transformation or crystal growth within the drug material itself. Here, a mathematical model was constructed to study the dissolution testing of a material, which undergoes such changes. The model consisted of two processes: the recrystallization of the drug from a supersaturated liquid state caused by the dissolution of the more soluble solid form and the crystal growth of the stable solid form at the surface of the drug formulation. Comparison to experimental data on theophylline dissolution showed that the results obtained with the model matched real solid-state changes and that it was able to distinguish between cases where the transformation was controlled either by solvent-mediated crystallization or solid-state crystal growth. Copyright © 2013 Elsevier B.V. All rights reserved.

Structural, thermodynamic, and mechanical properties of WCu solid solutions

NASA Astrophysics Data System (ADS)

Liang, C. P.; Wu, C. Y.; Fan, J. L.; Gong, H. R.

2017-11-01

Various properties of Wsbnd Cu solid solutions are systematically investigated through a combined use of first-principles calculation, cluster expansion, special quasirandom structures (SQS), and lattice dynamics. It is shown that SQS are effective to unravel the intrinsic nature of solid solutions, and that BCC and FCC W100-xCux solid solutions are energetically more stable when 0 ≤ x ≤ 70 and 70 < x ≤ 100, respectively. Calculations also reveal that the Debye model should be appropriate to derive thermodynamic properties of Wsbnd Cu, and that the coefficients of thermal expansion of W100-xCux solid solutions are much lower than those of corresponding mechanical mixtures. In addition, the G/B values of W100-xCux solid solutions reach a minimum at x = 50, which is fundamentally due to the softening of phonons as well as strong chemical bonding between W and Cu with a mainly metallic feature.

Mathematical modeling of ethanol production in solid-state fermentation based on solid medium' dry weight variation.

PubMed

Mazaheri, Davood; Shojaosadati, Seyed Abbas; Zamir, Seyed Morteza; Mousavi, Seyyed Mohammad

2018-04-21

In this work, mathematical modeling of ethanol production in solid-state fermentation (SSF) has been done based on the variation in the dry weight of solid medium. This method was previously used for mathematical modeling of enzyme production; however, the model should be modified to predict the production of a volatile compound like ethanol. The experimental results of bioethanol production from the mixture of carob pods and wheat bran by Zymomonas mobilis in SSF were used for the model validation. Exponential and logistic kinetic models were used for modeling the growth of microorganism. In both cases, the model predictions matched well with the experimental results during the exponential growth phase, indicating the good ability of solid medium weight variation method for modeling a volatile product formation in solid-state fermentation. In addition, using logistic model, better predictions were obtained.

Associations between breast milk feeding, introduction of solid foods, and weight gain in the first 12 months of life

PubMed Central

Klag, Elizabeth A.; McNamara, Kelly; Geraghty, Sheela R.; Keim, Sarah A.

2016-01-01

Background and Objectives Breast milk feeding and solid food introduction can influence infant growth, but are rarely examined together. The objectives were: describe relationships between feeding practices, feeding practices and weight gain, and how the relationship of breast milk feeding and growth may change when breastfed infants start solid foods before 6 months. Methods Data was analyzed on 438 infants from the Moms2Moms Study (2011–2012, Ohio), using multivariable linear and logistic regression models to explore each of the relationships. Results For each additional month of breast milk feeding, solid food introduction was delayed by 1.32 days (95% CI: 0.11 to 2.53) and average weight gain per month decreased by 5.05 grams (95% CI: 7.39 to 2.17). There was no association between solid food introduction and growth. Conclusions Longer breastfeeding duration was associated with slower growth regardless of solid food introduction. Age at solid food introduction was not associated with growth. PMID:25644649

Associations Between Breast Milk Feeding, Introduction of Solid Foods, and Weight Gain in the First 12 Months of Life.

PubMed

Klag, Elizabeth A; McNamara, Kelly; Geraghty, Sheela R; Keim, Sarah A

2015-10-01

Breast milk feeding and solid food introduction can influence infant growth, but are rarely examined together. The objectives were to describe relationships between feeding practices, feeding practices and weight gain, and how the relationship of breast milk feeding and growth may change when breastfed infants start solid foods before 6 months. Data were analyzed on 438 infants from the Moms2Moms Study (2011-2012, Ohio), using multivariable linear and logistic regression models to explore each of the relationships. For each additional month of breast milk feeding, solid food introduction was delayed by 1.32 days (95% CI 0.11 to 2.53) and average weight gain per month decreased by 5.05 g (95% CI 7.39 to 2.17). There was no association between solid food introduction and growth. Longer breastfeeding duration was associated with slower growth regardless of solid food introduction. Age at solid food introduction was not associated with growth. © The Author(s) 2015.

Smoking cessation in primary care clinics.

PubMed

Sippel, J M; Osborne, M L; Bjornson, W; Goldberg, B; Buist, A S

1999-11-01

To document smoking cessation rates achieved by applying the 1996 Agency for Health Care Policy and Research (AHCPR) smoking cessation guidelines for primary care clinics, compare these quit rates with historical results, and determine if quit rates improve with an additional motivational intervention that includes education as well as spirometry and carbon monoxide measurements. Randomized clinical trial. Two university-affiliated community primary care clinics. Two hundred five smokers with routinely scheduled appointments. All smokers were given advice and support according to AHCPR guidelines. Half of the subjects received additional education with spirometry and carbon monoxide measurements. Quit rate was evaluated at 9-month follow-up. Eleven percent of smokers were sustained quitters at follow-up. Sustained quit rate was no different for intervention and control groups (9% vs 14%; [OR] 0.6; 95% [CI] 0.2, 1.4). Nicotine replacement therapy was strongly associated with sustained cessation (OR 6.7; 95% CI 2.3, 19.6). Subjects without insurance were the least likely to use nicotine replacement therapy ( p =.05). Historical data from previously published studies showed that 2% of smokers quit following physician advice, and additional support similar to AHCPR guidelines increased the quit rate to 5%. The sustained smoking cessation rate achieved by following AHCPR guidelines was 11% at 9 months, which compares favorably with historical results. Additional education with spirometry did not improve the quit rate. Nicotine replacement therapy was the strongest predictor of cessation, yet was used infrequently owing to cost. These findings support the use of AHCPR guidelines in primary care clinics, but do not support routine spirometry for motivating patients similar to those studied here.

The effect of microgeometry, implant thickness and polyurethane chemistry on the foreign body response to subcutaneous implants.

PubMed

Ward, W Kenneth; Slobodzian, Emily P; Tiekotter, Kenneth L; Wood, Michael D

2002-11-01

We addressed the effect of implant thickness, implant porosity, and polyurethane (PU) chemistry on angiogenesis and on the foreign body response in rats. The following materials were implanted subcutaneously for 7 weeks then excised for histologic analysis: a solid PU; a solid polyurethane with silicone and polyethylene oxide (PU-S-PEO); porous expanded polytetrafluoroethylene (ePTFE); and porous polyvinyl alcohol sponge (PVA). Two thicknesses of PU-S-PEO were compared: 300 microns (thin) and 2000 microns (thick). Foreign body capsule (FBC) thickness was much less in PU-S-PEO implants than in PU implants. In addition, FBC were thinner in thin implants than in thick implants. FBC was much more dense in solid implants than in porous implants. As compared with solid implants, porous implants (PVA and ePTFE) led to a marked increase in the number of microvessels that developed adjacent to the implant, as observed both with hematoxylin/eosin staining and with an immunohistochemical anti-endothelial stain. We conclude that the polyethylene oxide and silicone moieties in PU reduce the thickness of the subsequent FBC. In addition, thin implants lead to a thin FBC. Porous implants (PVA and ePTFE) cause more angiogenesis than solid implants. These results may have implications for the measurement of blood-derived analytes by biosensors.

43 CFR 418.36 - Incentives for additional long term conservation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... be reduced by the incremental amount of evaporation which occurs as a result of the increased surface area of the reservoir due to the additional storage. The evaporation rate used will be either the net evaporation measured or the net historical average after precipitation is taken into account. The method of...

43 CFR 418.36 - Incentives for additional long term conservation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... be reduced by the incremental amount of evaporation which occurs as a result of the increased surface area of the reservoir due to the additional storage. The evaporation rate used will be either the net evaporation measured or the net historical average after precipitation is taken into account. The method of...

43 CFR 418.36 - Incentives for additional long term conservation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... be reduced by the incremental amount of evaporation which occurs as a result of the increased surface area of the reservoir due to the additional storage. The evaporation rate used will be either the net evaporation measured or the net historical average after precipitation is taken into account. The method of...

Federal Emergency Management and Homeland Security Organization: Historical Developments and Legislative Options

DTIC Science & Technology

2006-06-01

nuclear disaster warning systems,” and “preparedness and planning to reduce the consequences of major terrorist incidents.” In addition, the order...assistance functions,” in addition to dam safety, “natural and nuclear disaster warning systems,” and “the coordination of preparedness and planning to

Water recovery and solid waste processing for aerospace and domestic applications. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Murray, R. W.

1973-01-01

Water and sewage treatment systems are presented with concentration on the filtration of water. Equipment is described for organic removal, solids removal, nutrient removal, inorganic removal, and disinfection of the water. Such things as aseline hardware, additional piping connections, waste disposal, and costs involved are also reported.

Conversion of canola meal into a high-protein feed additive via solid-state fungal incubation process

USDA-ARS?s Scientific Manuscript database

The study goal was to determine the optimal fungal culture to reduce glucosinolates (GLS), fiber, and residual sugars while increasing the protein content and nutritional value of canola meal. Solid-state incubation conditions were used to enhance filamentous growth of the fungi. Flask trials were p...

Representation of solid and nutrient concentrations in irrigation water from tailwater recovery systems by surface water grab samples

USDA-ARS?s Scientific Manuscript database

Tailwater recovery (TWR) systems are being implemented on agricultural landscapes to create an additional source of irrigation water. Existing studies have sampled TWR systems using grab samples; however, the applicability of solids and nutrient concentrations in these samples to water being irrigat...

Investigating the Retention Mechanisms of Liquid Chromatography Using Solid-Phase Extraction Cartridges

ERIC Educational Resources Information Center

O'Donnell, Mary E.; Musial, Beata A.; Bretz, Stacey Lowery; Danielson, Neil D.; Ca, Diep

2009-01-01

Liquid chromatography (LC) experiments for the undergraduate analytical laboratory course often illustrate the application of reversed-phase LC to solve a separation problem, but rarely compare LC retention mechanisms. In addition, a high-performance liquid chromatography instrument may be beyond what some small colleges can purchase. Solid-phase…

Using the Pottery Wheel to Explore Topics in Calculus

ERIC Educational Resources Information Center

Farnell, Elin; Snipes, Marie A.

2015-01-01

Students sometimes struggle with visualizing the three-dimensional solids encountered in certain integral problems in a calculus class. We present a project in which students create solids of revolution with clay on a pottery wheel and estimate the volumes of these objects using Riemann sums. In addition to giving students an opportunity for…

Effect of toughened epoxy resin on partial discharge at solid-solid interface

NASA Astrophysics Data System (ADS)

Li, Manping; Wu, Kai; Zhang, Zhao; Cheng, Yonghong

2017-02-01

A series of solid-solid interfaces, consisting of ceramic-epoxy resin interface samples with a tip-plate electrode, were investigated by performing partial discharge tests and real-time electrical tree observations. A toughening agent was added to the epoxy resin at different ratios for comparison. The impact strength, differential scanning calorimetry (DSC) and dielectric properties of the cured compositions and ceramic were tested. The electric field strength at the tip was calculated based on Maxwell’s theory. The test results show that the addition of a toughener can improve the impact strength of epoxy resin but it decreases the partial discharge inception voltage (PDIV) of the interface sample. At the same time, toughening leads to complex branches of the electrical tree. The simulation result suggests that this reduction of the PDIV cannot be explained by a change of permittivity due to the addition of a toughening agent. The microstructural change caused by toughening was considered to be the key factor for lower PDIV and complex electrical tree branches. Supported by China Academy of Engineering Physics (Project 2014B05005).

In situ analysis of capacity fade in thin-film anodes for high performance Li-ion all-solid-state batteries

NASA Astrophysics Data System (ADS)

Leite, Marina S.; Gong, Chen; Ruzmetov, Dmitry; Talin, A. Alec

There is still a pressing need to understand how the solid-interfaces in Li-ion all-solid-batteries form, including their chemical composition and electrical characteristics. In order to resolve the origin of the degradation mechanism in Al anodes, we combine in situ scanning electron microscopy in ultra-high vacuum with electrochemical cycling, in addition to ex situ characterization of the morphological, chemical, and electrical changes of the Al anodes upon lithiation. An AlLi alloy capped by a stable Al-Li-O is formed on the top surface of the anode, trapping Li, which results in the capacity fade, from 48.0 to 41.5 μ.Ah/cm2 in two cycles. The addition of a Cu capping layer is insufficient to prevent the device degradation because of the fast Li diffusion within Al. Yet, Si present extremely stable cycling: >92% of capacity retention after 100 cycles, with average Coulombic efficiency of 98%. Our in situ measurements represent a new platform for probing the real-time degradation of electrodes in all-solid-state batteries for energy storage devices.

Classification of solid dispersions: correlation to (i) stability and solubility (ii) preparation and characterization techniques.

PubMed

Meng, Fan; Gala, Urvi; Chauhan, Harsh

2015-01-01

Solid dispersion has been a topic of interest in recent years for its potential in improving oral bioavailability, especially for poorly water soluble drugs where dissolution could be the rate-limiting step of oral absorption. Understanding the physical state of the drug and polymers in solid dispersions is essential as it influences both the stability and solubility of these systems. This review emphasizes on the classification of solid dispersions based on the physical states of drug and polymer. Based on this classification, stability aspects such as crystallization tendency, glass transition temperature (Tg), drug polymer miscibility, molecular mobility, etc. and solubility aspects have been discussed. In addition, preparation and characterization methods for binary solid dispersions based on the classification have also been discussed.

Supercritical water oxidation - Microgravity solids separation

NASA Technical Reports Server (NTRS)

Killilea, William R.; Hong, Glenn T.; Swallow, Kathleen C.; Thomason, Terry B.

1988-01-01

This paper discusses the application of supercritical water oxidation (SCWO) waste treatment and water recycling technology to the problem of waste disposal in-long term manned space missions. As inorganic constituents present in the waste are not soluble in supercritical water, they must be removed from the organic-free supercritical fluid reactor effluent. Supercritical water reactor/solids separator designs capable of removing precipitated solids from the process' supercritical fluid in zero- and low- gravity environments are developed and evaluated. Preliminary experiments are then conducted to test the concepts. Feed materials for the experiments are urine, feces, and wipes with the addition of reverse osmosis brine, the rejected portion of processed hygiene water. The solid properties and their influence on the design of several oxidation-reactor/solids-separator configurations under study are presented.

Highly solid-state emissive pyridinium-substituted tetraphenylethylene salts: emission color-tuning with counter anions and application for optical waveguides.

PubMed

Hu, Fang; Zhang, Guanxin; Zhan, Chi; Zhang, Wei; Yan, Yongli; Zhao, Yongsheng; Fu, Hongbing; Zhang, Deqing

2015-03-18

In this paper seven salts of pyridinium-substituted tetraphenylethylene with different anions are reported. They show typical aggregation-induced emission. Crystal structures of three of the salts with (CF(3)SO(2))(2) N(-), CF(3) SO(3)(-), and SbF(6)(-) as the respective counter anions, are determined. The emission behavior of their amorphous and crystalline solids is investigated. Both amorphous and crystalline solids, except for the one with I(-), are highly emissive. Certain amorphous solids are red-emissive with almost the same quantum yields and fluorescence life-times. However, some crystalline solids are found to show different emission colors varying from green to yellow. Thus, their emission colors can be tuned by the counter anions. Furthermore, certain crystalline solids are highly emissive compared to the respective amorphous solids. Such solid-state emission behavior of these pyridinium-substituted tetraphenylethylene salts is interpreted on the basis of their crystal structures. In addition, optical waveguiding behavior of fabricated microrods is presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Influence of liquid ceramic additive on binding of heavy metal during the vitrification of fly ash from municipal solid waste incinerator].

PubMed

Li, Run-dong; Nie, Yong-feng; Li, Ai-min; Wang, Lei; Chi, Yong; Cen, Ke-fa

2004-09-01

Vitrification process can effectively control the leachability of heavy metals in fly ash generated from municipal solid waste incinerator (MWSI). The use of liquid ceramic (LC) additive as a heavy metal chemical stabilization agent was evaluated for MSWI fly ash. The residuals of chromium, lead and zinc in slag increase by different degree with liquid ceramic additive at 1400 degrees C, while those of cadmium and copper decreases. The migrating characteristic of nickel is hardly affected by the additive less than 10%. The volatilization of Cr and Zn occurs after 61 minute with 10% addition of LC, and the binding efficiency of Cr decreases with increasing of melting temperature. The results indicate that the binding efficiency of heavy metals was affected greatly by LC additive and showed significant differences according to type of heavy metal during melting process. The short melting time (no longer than 33 min) is useful to obtain high binding efficiency of heavy metals.

Solid polymer electrolyte electrochemical storage cell containing a redox shuttle additive for overcharge protection

DOEpatents

Richardson, Thomas J.; Ross, Philip N.

1999-01-01

A class of organic redox shuttle additives is described, preferably comprising nitrogen-containing aromatics compounds, which can be used in a high temperature (85.degree. C. or higher) electrochemical storage cell comprising a positive electrode, a negative electrode, and a solid polymer electrolyte to provide overcharge protection to the cell. The organic redox additives or shuttles are characterized by a high diffusion coefficient of at least 2.1.times.10.sup.-8 cm.sup.2 /second and a high onset potential of 2.5 volts or higher. Examples of such organic redox shuttle additives include an alkali metal salt of 1,2,4-triazole, an alkali metal salt of imidazole, 2,3,5,6-tetramethylpyrazine, 1,3,5-tricyanobenzene, and a dialkali metal salt of 3-4-dihydroxy-3-cyclobutene-1,2-dione.

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds and Ionic Liquids. Sublimation, Vaporization, and Fusion Enthalpies from 1880 to 2015. Part 2. C11-C192

NASA Astrophysics Data System (ADS)

Acree, William; Chickos, James S.

2017-03-01

The second part of this compendium concludes with a collection of phase change enthalpies of organic molecules inclusive of C11-C192 reported over the period 1880-2015. Also included are phase change enthalpies including fusion, vaporization, and sublimation enthalpies for organometallic, ionic liquids, and a few inorganic compounds. Paper I of this compendium, published separately, includes organic compounds from C1 to C10 and describes a group additivity method for evaluating solid, liquid, and gas phase heat capacities as well as temperature adjustments of phase changes. Paper II of this compendium also includes an updated version of a group additivity method for evaluating total phase change entropies which together with the fusion temperature can be useful in estimating total phase change enthalpies. Other uses include application in identifying potential substances that either form liquid or plastic crystals or exhibit additional phase changes such as undetected solid-solid transitions or behave anisotropically in the liquid state.

SOLID SOLUTION EFFECTS ON THE THERMAL PROPERTIES IN THE MgAl2O4-MgGa2O4

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Hara, Kelley; Smith, Jeffrey D; Sander, Todd P.

Solid solution eects on thermal conductivity within the MgO-Al2O3-Ga2O3 system were studied. Samples with systematically varied additions of MgGa2O4 to MgAl2O4 were prepared and the laser ash technique was used to determine thermal diusivity at temperatures between 200C and 1300C. Heat capacity as a function of temperature from room temperature to 800C was also determined using dierential scanning calorimetry. Solid solution in the MgAl2O4-MgGa2O4 system decreases the thermal conductivity up to 1000C. At 200C thermal conductivity decreased 24% with a 5 mol% addition of MgGa2O4 to the system. At 1000C the thermal conductivity decreased 13% with a 5 mol% addition.more » Steady state calculations showed a 12.5% decrease in heat ux with 5 mol% MgGa2O4 considered across a 12 inch thickness.« less

Isotopic Fingerprints of Iron-Cyanide Complexes in the Environment.

PubMed

Mansfeldt, Tim; Höhener, Patrick

2016-07-19

Tracing the origin of iron-cyanide complexes in the environment is important because these compounds are potentially toxic. We determined the stable isotopic compositions of cyanide-carbon (CCN) and cyanide-nitrogen (NCN) in 127 contaminated solids and 11 samples of contaminated groundwater from coal carbonization sites, blast furnace operations, and commercial cyanide applications. Coal-carbonization-related cyanides had unique high mean δ(13)CCN values of -10.5 ± 3.5‰ for the solids and -16.1 ± 1.2‰ for the groundwater samples, while the values for blast furnace sludge (-26.9 ± 1.5‰), commercial cyanides (-26.0 ± 3.0‰), and their corresponding groundwaters were significantly lower. Determination of δ(13)CCN is a promising tool for identifying the source of cyanide contamination. However, for coal carbonization sites, historical research into the manufacturing process is necessary because a nonconventional gas works site exhibited exceptionally low δ(13)CCN values of -22.7 ± 1.7‰. The δ(15)NCN values for samples related to coal carbonization and blast furnaces overlapped within a range of +0.1 to +10.3‰, but very high δ(15)NCN values seemed to be indicative for a cyanide source in the blast furnace. In contrast, commercial cyanides tend to have lower δ(15)NCN values of -5.6 to +1.9‰ in solids and -0.5 to +3.0‰ in the groundwater.

Should the definition of "sleep hygiene" be antedated of a century? A historical note based on an old book by Paolo Mantegazza, rediscovered. To place in a new historical context the development of the concept of sleep hygiene.

PubMed

Gigli, Gian Luigi; Valente, Mariarosaria

2013-05-01

The article contains a historical note on the concept of sleep hygiene, developed in 1977 by Peter Hauri, who developed a set of sleep-promoting rules, considered the fundament for sleep-hygiene techniques. Somnologists, unanimously ascribed to Hauri the fatherhood of the lucky term, while numerous books included at least a section on sleep hygiene. "Inadequate sleep hygiene" was included as a nosological entity in the International Classification of Sleep Disorders. This article intends to demonstrate that the concept of sleep hygiene was developed many years before, thanks to the pioneering work of Paolo Mantegazza, a scientist and a professor in the Medical School of the University of Pavia, Italy. After presenting briefly the history of the University of Pavia and illustrating the profile of Paolo Mantegazza, the article presents the original book published by Mantegazza in 1864 (second edition in 1865). The authors report extensive citations of Mantegazza's original book dealing with sleep hygiene. Mantegazza's indications, compared with Hauri's rules show important similarities. The authors support the view that the fatherhood of sleep hygiene should be acknowledged to Mantegazza and antedated to 1864. Hauri keeps the merit of giving more solid scientific roots to the concept of sleep hygiene and of inserting it in the frame of modern sleep medicine.

The Tompkins County Solid Waste Annual Fee: Background and overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Penniman, P.W.

1995-05-01

This report outlines the development by Tompkins County of a new revenue source for solid waste programs -- The Solid Waste Annual Fee. Over the past two decades in New York State, regulatory demands and the decline in available landfill space have combined to cause a rapid escalation in the cost of solid waste disposal. While the New York State Department of Environmental Conservation (NYSDEC) has implemented tighter regulations for the siting of solid waste landfills, they have also mandated the permitting or closure of all existing landfills in the state. The result is that all communities have been requiredmore » to invest millions of dollars in landfill siting, closure and solid waste processing facilities. In addition, programs for reducing and recycling solid wastes have been mandated to reduce the outflow to landfills. Until recent years, solid waste services in most New York counties have been funded almost entirely through a collection of property taxes. During the past six years, fiscal stress has stimulated a movement toward funding solid waste programs by other means. Alternatives to the property tax include: (1) special assessment taxes or fees; (2) user charges (including tipping fees); and (3) intergovernment grants.« less

3D-Printing Electrolytes for Solid-State Batteries.

PubMed

McOwen, Dennis W; Xu, Shaomao; Gong, Yunhui; Wen, Yang; Godbey, Griffin L; Gritton, Jack E; Hamann, Tanner R; Dai, Jiaqi; Hitz, Gregory T; Hu, Liangbing; Wachsman, Eric D

2018-05-01

Solid-state batteries have many enticing advantages in terms of safety and stability, but the solid electrolytes upon which these batteries are based typically lead to high cell resistance. Both components of the resistance (interfacial, due to poor contact with electrolytes, and bulk, due to a thick electrolyte) are a result of the rudimentary manufacturing capabilities that exist for solid-state electrolytes. In general, solid electrolytes are studied as flat pellets with planar interfaces, which minimizes interfacial contact area. Here, multiple ink formulations are developed that enable 3D printing of unique solid electrolyte microstructures with varying properties. These inks are used to 3D-print a variety of patterns, which are then sintered to reveal thin, nonplanar, intricate architectures composed only of Li 7 La 3 Zr 2 O 12 solid electrolyte. Using these 3D-printing ink formulations to further study and optimize electrolyte structure could lead to solid-state batteries with dramatically lower full cell resistance and higher energy and power density. In addition, the reported ink compositions could be used as a model recipe for other solid electrolyte or ceramic inks, perhaps enabling 3D printing in related fields. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

EnviroAtlas - Historic Places by 12-digit HUC for the Conterminous United States

EPA Pesticide Factsheets

This EnviroAtlas dataset portrays the total number of historic places located within each 12-digit Hydrologic Unit (HUC). The historic places data were compiled from the National Park Service's National Register of Historic Places (NRHP), which provides official federal lists of districts, sites, buildings, structures and objects significant to American history, architecture, archeology, engineering, and culture. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

Reconstruction and restoration of historical buildings of transport infrastructure

NASA Astrophysics Data System (ADS)

Kareeva, Daria; Glazkova, Valeriya

2017-10-01

The aim of this article is to identify the main problems in the restoration of the historical objects. For this reason, it is rationally to collect and analyze the existing world experience of restoration. The information which was put together showed that there are some problems which are common and can be solved. In addition, the protection of the Monuments of Culture and Architecture Comittees always makes the restoration and reconstruction of the historical buildings complicated. By the examples of Germany, Italy and Russia it is shown that there are problems in organization, economy, planning and control. Engineers should think of and justify the methodology of organizing and monitoring of the restoration of the historical buildings. As a second solution, it will be possible to minimize time and financial costs through a favorable financial and legal background for investors and through the creation of a system of restoration work organizing. And for a faster process of restoration the imitation programs should be optimized for research and selection of the reconstruction technological and economic methods.

Idaho National Laboratory Cultural Resource Monitoring Report for FY 2009

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brenda R. Pace; Julie B. Braun

2009-10-01

This report describes the cultural resource monitoring activities of the Idaho National Laboratory’s (INL) Cultural Resource Management (CRM) Office during fiscal year 2009 (FY 2009). Throughout the year, thirty-eight cultural resource localities were revisited including: two locations with Native American human remains, one of which is a cave, two additional caves, twenty-two prehistoric archaeological sites, six historic homesteads, two historic stage stations, two historic trails, and two nuclear resources, including Experimental Breeder Reactor-I, which is a designated National Historic Landmark. Several INL project areas were also monitored in FY 2009 to assess project compliance with cultural resource recommendations and monitormore » the effects of ongoing project activities. Although impacts were documented at a few locations and trespassing citations were issued in one instance, no significant adverse effects that would threaten the National Register eligibility of any resources were observed. Monitoring also demonstrated that several INL projects generally remain in compliance with recommendations to protect cultural resources.« less

Predicting treatment effect from surrogate endpoints and historical trials: an extrapolation involving probabilities of a binary outcome or survival to a specific time

PubMed Central

Sargent, Daniel J.; Buyse, Marc; Burzykowski, Tomasz

2011-01-01

SUMMARY Using multiple historical trials with surrogate and true endpoints, we consider various models to predict the effect of treatment on a true endpoint in a target trial in which only a surrogate endpoint is observed. This predicted result is computed using (1) a prediction model (mixture, linear, or principal stratification) estimated from historical trials and the surrogate endpoint of the target trial and (2) a random extrapolation error estimated from successively leaving out each trial among the historical trials. The method applies to either binary outcomes or survival to a particular time that is computed from censored survival data. We compute a 95% confidence interval for the predicted result and validate its coverage using simulation. To summarize the additional uncertainty from using a predicted instead of true result for the estimated treatment effect, we compute its multiplier of standard error. Software is available for download. PMID:21838732

Historical warming reduced due to enhanced land carbon uptake

PubMed Central

Shevliakova, Elena; Stouffer, Ronald J.; Malyshev, Sergey; Krasting, John P.; Hurtt, George C.; Pacala, Stephen W.

2013-01-01

Previous studies have demonstrated the importance of enhanced vegetation growth under future elevated atmospheric CO2 for 21st century climate warming. Surprisingly no study has completed an analogous assessment for the historical period, during which emissions of greenhouse gases increased rapidly and land-use changes (LUC) dramatically altered terrestrial carbon sources and sinks. Using the Geophysical Fluid Dynamics Laboratory comprehensive Earth System Model ESM2G and a reconstruction of the LUC, we estimate that enhanced vegetation growth has lowered the historical atmospheric CO2 concentration by 85 ppm, avoiding an additional 0.31 ± 0.06 °C warming. We demonstrate that without enhanced vegetation growth the total residual terrestrial carbon flux (i.e., the net land flux minus LUC flux) would be a source of 65–82 Gt of carbon (GtC) to atmosphere instead of the historical residual carbon sink of 186–192 GtC, a carbon saving of 251–274 GtC. PMID:24062452

Urban Renewal Mega Projects and Residents' Quality of Life: Evidence from Historical Religious Center of Mashhad Metropolis.

PubMed

Forouhar, Amir; Hasankhani, Mahnoosh

2018-04-01

Urban decay is the process by which a historical city center, or an old part of a city, falls into decrepitude and faces serious problems. Urban management, therefore, implements renewal mega projects with the goal of physical and functional revitalization, retrieval of socioeconomic capacities, and improving of quality of life of residents. Ignoring the complexities of these large-scale interventions in the old and historical urban fabrics may lead to undesirable consequences, including an additional decline of quality of life. Thus, the present paper aims to assess the impact of renewal mega projects on residents' subjective quality of life, in the historical religious district of the holy city of Mashhad (Samen District). A combination of quantitative and qualitative methods of impact assessment, including questionnaires, semi-structured personal interviews, and direct observation, is used in this paper. The results yield that the Samen Renewal Project has significantly reduced the resident's subjective quality of life, due to its undesirable impacts on physical, socio-cultural, and economic environments.

Parametric study and performance analysis of hybrid rocket motors with double-tube configuration

NASA Astrophysics Data System (ADS)

Yu, Nanjia; Zhao, Bo; Lorente, Arnau Pons; Wang, Jue

2017-03-01

The practical implementation of hybrid rocket motors has historically been hampered by the slow regression rate of the solid fuel. In recent years, the research on advanced injector designs has achieved notable results in the enhancement of the regression rate and combustion efficiency of hybrid rockets. Following this path, this work studies a new configuration called double-tube characterized by injecting the gaseous oxidizer through a head end injector and an inner tube with injector holes distributed along the motor longitudinal axis. This design has demonstrated a significant potential for improving the performance of hybrid rockets by means of a better mixing of the species achieved through a customized injection of the oxidizer. Indeed, the CFD analysis of the double-tube configuration has revealed that this design may increase the regression rate over 50% with respect to the same motor with a conventional axial showerhead injector. However, in order to fully exploit the advantages of the double-tube concept, it is necessary to acquire a deeper understanding of the influence of the different design parameters in the overall performance. In this way, a parametric study is carried out taking into account the variation of the oxidizer mass flux rate, the ratio of oxidizer mass flow rate injected through the inner tube to the total oxidizer mass flow rate, and injection angle. The data for the analysis have been gathered from a large series of three-dimensional numerical simulations that considered the changes in the design parameters. The propellant combination adopted consists of gaseous oxygen as oxidizer and high-density polyethylene as solid fuel. Furthermore, the numerical model comprises Navier-Stokes equations, k-ε turbulence model, eddy-dissipation combustion model and solid-fuel pyrolysis, which is computed through user-defined functions. This numerical model was previously validated by analyzing the computational and experimental results obtained for conventional hybrid rocket designs. In addition, a performance analysis is conducted in order to evaluate the influence in the performance provoked by the possible growth of the diameter of the inner fuel grain holes during the motor operation. The latter phenomenon is known as burn through holes. Finally, after a statistical analysis of the data, a regression rate expression as a function of the design parameters is obtained.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herman, D.

The Savannah River Site (SRS) Actinide Removal Process has been processing salt waste since 2008. This process includes a filtration step in the 512-S facility. Initial operations included the addition, or strike, of monosodium titanate (MST) to remove soluble actinides and strontium. The added MST and any entrained sludge solids were then separated from the supernate by cross flow filtration. During this time, the filter operations have, on many occasions, been the bottleneck process limiting the rate of salt processing. Recently, 512-S- has started operations utilizing “No-MST” where the MST actinide removal strike was not performed and the supernate wasmore » simply pre-filtered prior to Cs removal processing. Direct filtration of decanted tank supernate, as demonstrated in 512-S, is the proposed method of operation for the Hanford Low Activity Waste Pretreatment System (LAWPS) facility. Processing decanted supernate without MST solids has been demonstrated for cross flow filtration to provide a significant improvement in production with the SRS Salt Batches 8 and 9 feed chemistries. The average filtration rate for the first 512-S batch processing cycle using No-MST has increased filtrate production by over 35% of the historical average. The increase was sustained for more than double the amount of filtrate batches processed before cleaning of the filter was necessary. While there are differences in the design of the 512-S and Hanford filter systems, the 512-S system should provide a reasonable indication of LAWPS filter performance with similar feed properties. Based on the data from the 512-S facility and with favorable feed properties, the LAWPS filter, as currently sized at over twice the size of the 512-S filter (532 square feet filtration area versus 235 square feet), has the potential to provide sustained filtrate production at the upper range of the planned LAWPS production rate of 17 gpm.« less

Actions at Hamburg International Association of Seismology and Physics of the Earth's Interior

NASA Astrophysics Data System (ADS)

The third Workshop on Historical Seismograms, held in Hamburg on August 18-19, 1983, in conjunction with the meeting of the International Union of Geodesy and Geophysics in Hamburg, Federal Republic of Germany, was specifically organized to discuss the status of historical seismic data for Latin America and Europe. Since it is unlikely that an additional workshop will be held on this subject, reports for other regions were included as well.In the first session, H. Meyers described the purpose of the workshop and gave some history of the previous activities of the IASPEI/Unesco Working Group on Historical Seismograms. E.R. Engdahl noted that thus far more than 500,000 seismograms have been filmed as part of the Historical Microfilming Project and emphasized the importance of the activities to be covered during the workshop. M. Hashizume, representing Unesco, described the importance of historical seismic data and the Unesco interests in having these data available for the analysis of seismic risks, particularly in areas where the recurrence rate of significant earthquakes is very low and for regions where much data do not exist. He mentioned that both these conditions occur frequently in developing nations.

Kennedy Space Center Press Site (SWMU 074) Interim Measure Report

NASA Technical Reports Server (NTRS)

Applegate, Joseph L.

2015-01-01

This report summarizes the Interim Measure (IM) activities conducted at the Kennedy Space Center (KSC) Press Site ("the Press Site"). This facility has been designated as Solid Waste Management Unit 074 under KSC's Resource Conservation and Recovery Act Corrective Action program. The activities were completed as part of the Vehicle Assembly Building (VAB) Area Land Use Controls Implementation Plan (LUCIP) Elimination Project. The purpose of the VAB Area LUCIP Elimination Project was to delineate and remove soil affected with constituents of concern (COCs) that historically resulted in Land Use Controls (LUCs). The goal of the project was to eliminate the LUCs on soil. LUCs for groundwater were not addressed as part of the project and are not discussed in this report. This report is intended to meet the Florida Department of Environmental Protection (FDEP) Corrective Action Management Plan requirement as part of the KSC Hazardous and Solid Waste Amendments permit and the U.S. Environmental Protection Agency's (USEPA's) Toxic Substance Control Act (TSCA) self-implementing polychlorinated biphenyl (PCB) cleanup requirements of 40 Code of Federal Regulations (CFR) 761.61(a).

Use of Several Thermal Analysis Techniques on a Hypalon Paint Coating for the Solid Rocket Booster (SRB) of the Space Shuttle

NASA Technical Reports Server (NTRS)

Wingard, Charles D.; Whitaker, Ann F. (Technical Monitor)

2000-01-01

White Hypalon paint is brush-applied as a moisture barrier coating over cork surfaces on each of the two Space Shuttle SRBs. Fine cracks have been observed in the Hypalon coating three times historically on laboratory witness panels, but never on flight hardware. Samples of the cracked and standard ("good") Hypalon were removed from witness panel cork surfaces, and were tested in 1998 by Thermogravimetric Analysis (TGA), TMA and Differential Scanning Calorimetry (DSC) thermal analysis techniques. The TGA data showed that at 700C, where only paint pigment solids remain, the cracked material had about 9 weight percent more material remaining than the standard material, probably indicating incomplete mixing of the paint before it was brush-applied to produce the cracked material. Use of the TMA film/fiber technique showed that the average modulus (stiffness) vs. temperature was about 3 to 6 times higher for the cracked material than for the standard material. The TMA data also showed that an increase in coating thickness for the cracked Hypalon was not a factor in the anomaly.

NASA developments in solid state power amplifiers

NASA Technical Reports Server (NTRS)

Leonard, Regis F.

1990-01-01

Over the last ten years, NASA has undertaken an extensive program aimed at development of solid state power amplifiers for space applications. Historically, the program may be divided into three phases. The first efforts were carried out in support of the advanced communications technology satellite (ACTS) program, which is developing an experimental version of a Ka-band commercial communications system. These first amplifiers attempted to use hybrid technology. The second phase was still targeted at ACTS frequencies, but concentrated on monolithic implementations, while the current, third phase, is a monolithic effort that focusses on frequencies appropriate for other NASA programs and stresses amplifier efficiency. The topics covered include: (1) 20 GHz hybrid amplifiers; (2) 20 GHz monolithic MESFET power amplifiers; (3) Texas Instruments' (TI) 20 GHz variable power amplifier; (4) TI 20 GHz high power amplifier; (5) high efficiency monolithic power amplifiers; (6) GHz high efficiency variable power amplifier; (7) TI 32 GHz monolithic power amplifier performance; (8) design goals for Hughes' 32 GHz variable power amplifier; and (9) performance goals for Hughes' pseudomorphic 60 GHz power amplifier.

In situ analytical techniques for battery interface analysis.

PubMed

Tripathi, Alok M; Su, Wei-Nien; Hwang, Bing Joe

2018-02-05

Lithium-ion batteries, simply known as lithium batteries, are distinct among high energy density charge-storage devices. The power delivery of batteries depends upon the electrochemical performances and the stability of the electrode, electrolytes and their interface. Interfacial phenomena of the electrode/electrolyte involve lithium dendrite formation, electrolyte degradation and gas evolution, and a semi-solid protective layer formation at the electrode-electrolyte interface, also known as the solid-electrolyte interface (SEI). The SEI protects electrodes from further exfoliation or corrosion and suppresses lithium dendrite formation, which are crucial needs for enhancing the cell performance. This review covers the compositional, structural and morphological aspects of SEI, both artificially and naturally formed, and metallic dendrites using in situ/in operando cells and various in situ analytical tools. Critical challenges and the historical legacy in the development of in situ/in operando electrochemical cells with some reports on state-of-the-art progress are particularly highlighted. The present compilation pinpoints the emerging research opportunities in advancing this field and concludes on the future directions and strategies for in situ/in operando analysis.

Survival results in five malignant neoplasms separated by a decade at Institut Català d'Oncologia, Spain.

PubMed

Germá-Lluch, José Ramón; Petriz, Lourdes; Lopez, Pau; Asensio, Esther

2018-02-23

Five years' data relative survival (RS) is presented in 3 solid tumours: breast, colorectal (CRC) and lung and 2 haematologic neoplasms: large B cell lymphoma (NHL-B) and multiple myeloma (MM) treated at Institut Català d'Oncologia between 2010-2011 in comparison with the results obtained in a historical special cohort from 1998-1999. A database was created in a common safe and accessible repository. We have introduced more than 5,000 medical records. To analyse the results the statistical package R ® was used for RS. The overall RS at 5 years for 2010-2011 was: CRC 67%, breast 93.6%, lung 28%, NHL-B 68% and MM 62%, while for 1998-1999 is was: CRC 61.8%, breast 88.8%, lung 23.1%, NHL-B 67.7%, and MM 43.4%. Comparative results have shown a 5% overall improvement in RS for the 3 solid tumours, a significant increase in MM and a stabilisation in the NHL-B. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

Experimental comparison of residual stresses for a thermomechanical model for the simulation of selective laser melting

DOE PAGES

Hodge, N. E.; Ferencz, R. M.; Vignes, R. M.

2016-05-30

Selective laser melting (SLM) is an additive manufacturing process in which multiple, successive layers of metal powders are heated via laser in order to build a part. Modeling of SLM requires consideration of the complex interaction between heat transfer and solid mechanics. Here, the present work describes the authors initial efforts to validate their first generation model. In particular, the comparison of model-generated solid mechanics results, including both deformation and stresses, is presented. Additionally, results of various perturbations of the process parameters and modeling strategies are discussed.

The effect of thermal and organic additive in morphology of ceramic based silicate

NASA Astrophysics Data System (ADS)

Ginting, J.; Bangun, N.; Sembiring, H. Br; Putri, N. K.

2017-04-01

M-Silicate (M = Mg, Ca) has been prepared by exchange metal reaction from M-Chloride salts and sodium silicate. The resulting white solid of chloride salts then heated at 700, 800, 900 and 1000 °C. Due to increase the porosity of M-Silicate, 1,2-propanediol, oleic acid and glycerol were added, then formed M-silicates were heated at 800 °C. Then, obtained white solid M-Silicates were characterized by Scanning Electron Microscopy (SEM). SEM images show the variance of surface morphology when the temperature increases. The addition of organic compounds is involved in surface modification.

Evaluation of modified asphalt using chlorinated and maleated waste polymers.

DOT National Transportation Integrated Search

2002-07-01

Asphalt modification using polymeric additives derived from solid wastes, i.e. polyolefins, is reported. Chlorination of polyethylene can be controlled to produce semicrystalline polymeric additives. Differential scanning calorimetry can be used to d...

Turning refuse into resource: a study on aerobic composting.

PubMed

Janakiram, T; Sridevi, K

2012-07-01

The management of solid waste disposal had been a perennial problem every where in our country. In order to overcome this problem one possible solution is to compost the solid waste in the presence of air, so that it may be converted into an useful manure. With this intention, solid wastes like coir waste and water hyacinth had been collected and composted with the addition of cow dung. The composted material had been examined for the physical and chemical parameters. The content of macronutrients was found to be higher as the period of composting increased. There were gradual variations in the case of other parameters. A comparative account of the two types of solid waste is also given.

Growth behavior of LiMn{sub 2}O{sub 4} particles formed by solid-state reactions in air and water vapor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kozawa, Takahiro, E-mail: t-kozawa@jwri.osaka-u.ac.jp; Yanagisawa, Kazumichi; Murakami, Takeshi

Morphology control of particles formed during conventional solid-state reactions without any additives is a challenging task. Here, we propose a new strategy to control the morphology of LiMn{sub 2}O{sub 4} particles based on water vapor-induced growth of particles during solid-state reactions. We have investigated the synthesis and microstructural evolution of LiMn{sub 2}O{sub 4} particles in air and water vapor atmospheres as model reactions; LiMn{sub 2}O{sub 4} is used as a low-cost cathode material for lithium-ion batteries. By using spherical MnCO{sub 3} precursor impregnated with LiOH, LiMn{sub 2}O{sub 4} spheres with a hollow structure were obtained in air, while angulated particlesmore » with micrometer sizes were formed in water vapor. The pore structure of the particles synthesized in water vapor was found to be affected at temperatures below 700 °C. We also show that the solid-state reaction in water vapor is a simple and valuable method for the large-scale production of particles, where the shape, size, and microstructure can be controlled. - Graphical abstract: This study has demonstrated a new strategy towards achieving morphology control without the use of additives during conventional solid-state reactions by exploiting water vapor-induced particle growth. - Highlights: • A new strategy to control the morphology of LiMn{sub 2}O{sub 4} particles is proposed. • Water vapor-induced particle growth is exploited in solid-state reactions. • The microstructural evolution of LiMn{sub 2}O{sub 4} particles is investigated. • The shape, size and microstructure can be controlled by solid-state reactions.« less

Influence of solid dairy manure and compost with and without alum on survival of indicator bacteria in soil and on potato.

PubMed

Entry, James A; Leytem, April B; Verwey, Sheryl

2005-11-01

We measured Escherichia coli, Enterococcus spp. and fecal coliform numbers in soil and on fresh potato skins after addition of solid dairy manure and dairy compost with and without alum (Al(2)(SO(4))(3)) treatment 1, 7, 14, 28, 179 and 297 days after application. The addition of dairy compost or solid dairy manure at rates to meet crop phosphorus uptake did not consistently increase E. coli and Enterococcus spp. and fecal coliform bacteria in the soil. We did not detect E. coli in any soil sample after the first sampling day. Seven, 14, 28, 179 and 297 days after solid dairy waste and compost and alum were applied to soil, alum did not consistently affect Enterococcus spp. and fecal coliform bacteria in the soil. We did not detect E. coli in any soil, fresh potato skin or potato wash-water at 214 days after dairy manure or compost application regardless of alum treatment. Dairy compost or solid dairy manure application to soil at rates to meet crop phosphorus uptake did not consistently increase Enterococcus spp. and fecal coliform numbers in bulk soil. Solid dairy manure application to soil at rates to meet crop phosphorus uptake, increased Enterococcus spp. and fecal coliform numbers in potato rhizosphere soil. However, fresh potato skins had higher Enterococcus spp. and fecal coliform numbers when solid dairy manure was added to soil compared to compost, N and P inorganic fertilizer and N fertilizer treatments. We did not find any E. coli, Enterococcus or total coliform bacteria on the exterior of the tuber, within the peel or within a whole baked potato after microwave cooking for 5 min.

Development of an unresolved CFD-DEM model for the flow of viscous suspensions and its application to solid-liquid mixing

NASA Astrophysics Data System (ADS)

Blais, Bruno; Lassaigne, Manon; Goniva, Christoph; Fradette, Louis; Bertrand, François

2016-08-01

Although viscous solid-liquid mixing plays a key role in the industry, the vast majority of the literature on the mixing of suspensions is centered around the turbulent regime of operation. However, the laminar and transitional regimes face considerable challenges. In particular, it is important to know the minimum impeller speed (Njs) that guarantees the suspension of all particles. In addition, local information on the flow patterns is necessary to evaluate the quality of mixing and identify the presence of dead zones. Multiphase computational fluid dynamics (CFD) is a powerful tool that can be used to gain insight into local and macroscopic properties of mixing processes. Among the variety of numerical models available in the literature, which are reviewed in this work, unresolved CFD-DEM, which combines CFD for the fluid phase with the discrete element method (DEM) for the solid particles, is an interesting approach due to its accurate prediction of the granular dynamics and its capability to simulate large amounts of particles. In this work, the unresolved CFD-DEM method is extended to viscous solid-liquid flows. Different solid-liquid momentum coupling strategies, along with their stability criteria, are investigated and their accuracies are compared. Furthermore, it is shown that an additional sub-grid viscosity model is necessary to ensure the correct rheology of the suspensions. The proposed model is used to study solid-liquid mixing in a stirred tank equipped with a pitched blade turbine. It is validated qualitatively by comparing the particle distribution against experimental observations, and quantitatively by compairing the fraction of suspended solids with results obtained via the pressure gauge technique.

Uptake of Ra during the recrystallization of barite: a microscopic and time of flight-secondary ion mass spectrometry study.

PubMed

Klinkenberg, Martina; Brandt, Felix; Breuer, Uwe; Bosbach, Dirk

2014-06-17

A combined macroscopic and microanalytical approach was applied on two distinct barite samples from Ra uptake batch experiments using time of flight-secondary ion mass spectrometry (ToF-SIMS) and detailed scanning electron microscopy (SEM) investigations. The experiments were set up at near to equilibrium conditions to distinguish between two possible scenarios for the uptake of Ra by already existent barite: (1) formation of a Ba1-xRaxSO4 solid solution surface layer on the barite or (2) a complete recrystallization, leading to homogeneous Ba1-xRaxSO4 crystals. It could be clearly shown that Ra uptake in all barite particles analyzed within this study is not limited to the surface but extends to the entire solid. For most grains a homogeneous distribution of Ra could be determined, indicating a complete recrystallization of barite into a Ba1-xRaxSO4 solid solution. The maxima of the Ra/Ba intensity ratio distribution histograms calculated from ToF-SIMS are identical with the expected Ra/Ba ratios calculated from mass balance assuming a complete recrystallization. In addition, the role of Ra during the recrystallization of barite was examined via detailed SEM investigations. Depending on the type of barite used, an additional coarsening effect or a strong formation of oriented aggregates was observed compared to blank samples without Ra. In conclusion, the addition of Ra to a barite at close to equilibrium conditions has a major impact on the system leading to a fast re-equilibration of the solid to a Ba1-xRaxSO4 solid solution and visible effects on the particle size distribution, even at room temperature.

Thermal properties of spinel based solid solutions

NASA Astrophysics Data System (ADS)

O'Hara, Kelley Rae

Solid solution formation in spinel based systems proved to be a viable approach to decreasing thermal conductivity. Samples with systematically varied additions of MgGa2O4 to MgAl2O 4 were prepared and thermal diffusivity was measured using the laser flash technique. Additionally, heat capacity was measured using differential scanning calorimetry and modeled for the MgAl2O4-MgGa 2O4 system. At 200°C thermal conductivity decreased 24% with a 5 mol% addition of MgGa2O4 to the system. The solid solution continued to decrease the thermal conductivity by 13% up to 1000°C with 5 mol% addition. The decrease in thermal conductivity ultimately resulted in a decrease in heat flux when applied to a theoretical furnace lining, which could lead to energy savings in industrial settings. The MgAl2O4-Al2O3 phase equilibria was investigated to fully understand the system and the thermal properties at elevated temperatures. The solvus line between MgAl2O4 and Al2O3 has been defined at 79.6 wt% Al 2O3 at 1500°C, 83.0 wt% Al2O4 at 1600°C, and 86.5 wt% Al2O3 at 1700°C. A metastable region has been identified at temperatures up to 1700°C which could have significant implications for material processing and properties. The spinel solid solution region has been extended to form an infinite solid solution with Al2O3 at elevated temperatures. A minimum in melting at 1975°C and a chemistry of 96 wt% Al2O3 rather than a eutectic is present. Thermal properties in the MgAl2O4-Al2O 3 system were investigated in both the single phase solid solution region and the two phase region. The thermal diffusivity decreased through the MgAl 2O4 solid solution region and was at a minimum through the entire metastable (nucleation and growth) region. As Al2O 3 became present as a second phase the thermal diffusivity increased with Al2O3 content. There was an 11.7% increase in thermal diffusivity with a change in overall chemistry of 85.20 wt% Al2O 3 to 87.71 wt% Al2O3, due to the drastic change in final chemistry (38.3 wt% Al20 3) caused by the nucleation and growth region in the system.

Effect of ca+2 addition on the properties of ce0.8gd0.2o2-δ for it-sofc

NASA Astrophysics Data System (ADS)

Koteswararao, P.; Buchi Suresh, M.; Wani, B. N.; Bhaskara Rao, P. V.; Varalaxmi, P.

2018-03-01

This paper reports the effect of Ca2+ addition on the structural and electrical properties of Ce0.8Gd0.2O2-δ(GDC) electrolyte for low temperature solid oxide fuel cell application. The Ca (0, 0.5, 1 and 2 mol %) doped GDC solid electrolytes have been prepared by solid state method. The sintered densities of the samples are greater than 95%. XRD study reveals the cubic fluorite structure. The microstructure of the samples sintered at 1400°C resulted into grain sizes in the range of 1.72 to 10.20 μm. Raman spectra show the presence of GDC single phase. AC impedance analysis is used to measure the ionic conductivity of the electrolyte. Among all the compositions, the highest conductivity is observed in the GDC sample with 0.5 mol% Ca addition. Nyquist plots resulted in multiple redoxation process such as grain and grain boundary conductions to final conductivity. Estimated blocking factor is lower for the GDC electrolyte with 0.5mol% Ca, indicating that Ca addition was promoted grain boundary conduction. Activation energies were calculated from Arrhenius plot and are found in the range of 1eV.

Effect of NaI/I 2 mediators on properties of PEO/LiAlO 2 based all-solid-state supercapacitors

NASA Astrophysics Data System (ADS)

Yin, Yijing; Zhou, Juanjuan; Mansour, Azzam N.; Zhou, Xiangyang

NaI/I 2 mediators and activated carbon were added into poly(ethylene oxide) (PEO)/lithium aluminate (LiAlO 2) electrolyte to fabricate composite electrodes. All solid-state supercapacitors were fabricated using the as prepared composite electrodes and a Nafion 117 membrane as a separator. Cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge measurements were conducted to evaluate the electrochemical properties of the supercapacitors. With the addition of NaI/I 2 mediators, the specific capacitance increased by 27 folds up to 150 F g -1. The specific capacitance increased with increases in the concentration of mediators in the electrodes. The addition of mediators also reduced the electrode resistance and rendered a higher electron transfer rate between mediator and mediator. The stability of the all-solid-state supercapacitor was tested over 2000 charge/discharge cycles.

Anaerobic digestion of municipal solid waste: Utility of process residues as a soil amendment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rivard, C.J.; Nagle, N.J.; Kay, B.D.

1995-12-31

Tuna processing wastes (sludges high in fat, oil, and grease [FOG]) and municipal solid waste (MSW) generated on Tutuila Island, American Samoa, represent an ongoing disposal challenge. The biological conversion of the organic fraction of these wastes to useful products, including methane and fertilizer-grade residue, through anaerobic high-solids digestion is currently in scale-up development. The suitability of the anaerobic digestion residues as a soil amendment was evaluated through extensive chemical analysis and greenhouse studies using corn as an indicator crop. Additionally, native Samoan soil was used to evaluate the specific application rates for the compost. Experiments established that anaerobic residuesmore » increase crop yields in direct proportion to increases in the application rate. Additionally, nutrient saturation was not demonstrated within the range of application rates evaluated for the Samoan soil. Beyond nutrient supplementation, organic residue amendment to Samoan soil imparts enhanced water and nutrient-binding capacities.« less

Using Wannier functions to improve solid band gap predictions in density functional theory

DOE PAGES

Ma, Jie; Wang, Lin-Wang

2016-04-26

Enforcing a straight-line condition of the total energy upon removal/addition of fractional electrons on eigen states has been successfully applied to atoms and molecules for calculating ionization potentials and electron affinities, but fails for solids due to the extended nature of the eigen orbitals. Here we have extended the straight-line condition to the removal/addition of fractional electrons on Wannier functions constructed within the occupied/unoccupied subspaces. It removes the self-interaction energies of those Wannier functions, and yields accurate band gaps for solids compared to experiments. It does not have any adjustable parameters and the computational cost is at the DFT level.more » This method can also work for molecules, providing eigen energies in good agreement with experimental ionization potentials and electron affinities. Our approach can be viewed as an alternative approach of the standard LDA+U procedure.« less

How-to-Do-It: Diatoms: The Ignored Alga in High School Biology.

ERIC Educational Resources Information Center

Hungerford, James J.

1988-01-01

Provides historical background, descriptions, uses and basis for identification of diatoms. Explains collection, dry-mount cleaning, and preparation procedures of the algae. Cites additional resources. (RT)

Trace elements biomonitoring in a historical mining district (les Malines, France).

PubMed

Saunier, Jean-Baptiste; Losfeld, Guillaume; Freydier, Rémi; Grison, Claude

2013-11-01

The aim of this study is to investigate the trace elements (TE) contents of potential biomonitors in a historical Zn-Pb mining district: apiary products (honey, royal-jelly and beeswax) lichen and moss were sampled and analysed. In spite of high TE concentrations in mining waste and soil, apiary products are free of TE contamination originating from historical mining. Lichen/moss show high TE levels, which suggest atmospheric input of local dust. Pb isotopes analysis proved the origin of TE found in lichen/moss to be mainly mining waste. These results help discuss the choice of relevant organisms for monitoring TE in the environment and bring additional data on the potential impacts of brownfields left after mining, especially on food products from apiaries. Copyright © 2013 Elsevier Ltd. All rights reserved.

Background Information Document for Updating AP42 Section 2.4 for Estimating Emissions from Municipal Solid Waste Landfills

EPA Science Inventory

This revised draft document was prepared for U.S. EPA's Office of Research and Development, and describes the data analysis undertaken to update the Municipal Solid Waste (MSW) Landfill section of AP-42. This 2008 update includes the addition of data from 62 landfill gas emission...

Alkene Isomerization Using a Solid Acid as Activator and Support for a Homogeneous Catalyst

ERIC Educational Resources Information Center

Seen, Andrew J.

2004-01-01

An upper-level undergraduate experiment that, in addition to introducing students to catalysis using an air sensitive transition-metal complex, introduces the use of a solid acid as an activator and support for the catalyst is developed. The increased stability acquired in the course of the process affords the opportunity to characterize the…

Assessment of bioburden encapsulated in bulk materials

NASA Astrophysics Data System (ADS)

Schubert, Wayne W.; Newlin, Laura; Chung, Shirley Y.; Ellyin, Raymond

2016-05-01

The National Aeronautics and Space Administration (NASA) imposes bioburden limitations on all spacecraft destined for solar system bodies that might harbor evidence of extant or extinct life. The subset of microorganisms trapped within solid materials during manufacture and assembly is referred to as encapsulated bioburden. In the absence of spacecraft-specific data, NASA relies on specification values to estimate total spacecraft encapsulated bioburden, typically 30 endospores/cm3 or 300 viable cells/cm3 in non-electronic materials. Specification values for endospores have been established conservatively, and represent no less than an order of magnitude greater abundance than that derived from empirical assessments of actual spacecraft materials. The goal of this study was to generate data germane to determining whether revised bulk encapsulated material values (lower than those estimated by historical specifications) tailored specifically to the materials designated in modern-day spacecraft design could be used, on a case-by-case basis, to comply with planetary protection requirements. Organic materials having distinctly different chemical properties and configurations were selected. This required more than one experimental and analytical approach. Filtration was employed for liquid electrolytes, lubricants were suspended in an aqueous solution and solids (wire and epoxy sealant) were cryogenically milled. The final data characteristic for all bioburden estimates was microbial colony formation in rich agar growth medium. To assess survival potential, three non-spore-forming bacterial cell lines were systematically encapsulated in an epoxy matrix, liberated via cryogenic grinding, and cultured. Results suggest that bulk solid materials harbor significantly fewer encapsulated microorganisms than are estimated by specification values. Lithium-ion battery electrolyte reagents housed fewer than 1 CFU/cm3. Results also demonstrated that non-spore-forming microorganisms are capable of surviving encapsulation within, and liberation from, epoxy solids. It must be noted, however, that all purposely spiked experimental solids, resulted in very low recovery (1 × 10-3-1 × 10-5 CFU/cm3) of viable organisms.

Lubrication of rigid ellipsida solids

NASA Technical Reports Server (NTRS)

Hamrock, B. J.; Dowson, D.

1982-01-01

The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds boundary conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza' classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared by using the exact expression for the film in the analysis. Contour plots are known that indicate in detail the pressure developed between the solids.

Composition and method of preparation of solid state dye laser rods

DOEpatents

Hermes, Robert E.

1992-01-01

The present invention includes solid polymeric-host laser rods prepared using bulk polymerization of acrylic acid ester comonomers which, when admixed with dye(s) capable of supporting laser oscillation and polymerized with a free radical initiator under mild thermal conditions, produce a solid product having the preferred properties for efficient lasing. Unsaturated polymerizable laser dyes can also be employed as one of the comonomers. Additionally, a method is disclosed which alleviates induced optical stress without having to anneal the polymers at elevated temperatures (>85.degree. C.).

Hybrid rockets - Combining the best of liquids and solids

NASA Technical Reports Server (NTRS)

Cook, Jerry R.; Goldberg, Ben E.; Estey, Paul N.; Wiley, Dan R.

1992-01-01

Hybrid rockets employing liquid oxidizer and solid fuel grain answers to cost, safety, reliability, and environmental impact concerns that have become as prominent as performance in recent years. The oxidizer-free grain has limited sensitivity to grain anomalies, such as bond-line separations, which can cause catastrophic failures in solid rocket motors. An account is presently given of the development effort associated with the AMROC commercial hybrid booster and component testing efforts at NASA-Marshall. These hybrid rockets can be fired, terminated, inspected, evaluated, and restarted for additional testing.

Method for improving the sedimentation and filterability of coal-derived liquids

DOEpatents

Katz, Sidney; Rodgers, Billy R.

1979-01-02

An improvement in the separation of suspended solids from coal-derived liquids by a separations process in which solids size is a separations parameter is achieved by contacting the coal-derived liquid containing suspended solids with an effective amount of an additive selected from the group of sulfuric acid, phosphoric acid, phosphoric anhydride and salts of sulfuric and phosphoric acid, and maintaining the contacted liquid at a temperature within the range of about 150.degree.-400.degree. C and for a time sufficient to achieve the desired separation rate.