Science.gov

Sample records for additional tests performed

  1. Development of additional tasks for the executive function performance test.

    PubMed

    Hahn, Bridget; Baum, Carolyn; Moore, Jennifer; Ehrlich-Jones, Linda; Spoeri, Susan; Doherty, Meghan; Wolf, Timothy J

    2014-01-01

    OBJECTIVE. The Executive Function Performance Test (EFPT) is a reliable and valid performance-based assessment of executive function for people with stroke. The objective of this study was to enhance the clinical utility of the EFPT by developing and testing additional tasks for the EFPT in the Alternate EFPT (aEFPT). METHOD. We performed a cross-sectional study with poststroke participants (n = 25) and healthy control participants (n = 25). All participants completed a neuropsychological assessment battery and both the EFPT and the aEFPT. RESULTS. No statistically significant differences were found between the EFPT and the aEFPT when examining total scores, construct scores, and two overall task scores. Correlations between the aEFPT and the neuropsychological measures were adequate to strong (r2s = .59-.83). CONCLUSION. The aEFPT tasks are comparable to the original EFPT tasks, providing occupational therapy practitioners with additional tasks that can be used clinically to identify performance-based executive function deficits in people with stroke.

  2. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Provisions' data analysis, recordkeeping, and reporting requirements in § 63.7(g) refer to the Notification... agreement. (b) Data shall be reduced in accordance with the EPA approved methods specified in the applicable subpart or, if other test methods are used, the data and methods shall be validated according to...

  3. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... provided to the Administrator. (2) When the General Provisions' data analysis, recordkeeping, and reporting... delegated State or local agency) by mutual agreement. (b) Data shall be reduced in accordance with the EPA approved methods specified in the applicable subpart or, if other test methods are used, the data...

  4. Performance testing of asphalt concrete containing crumb rubber modifier and warm mix additives

    NASA Astrophysics Data System (ADS)

    Ikpugha, Omo John

    Utilisation of scrap tire has been achieved through the production of crumb rubber modified binders and rubberised asphalt concrete. Terminal and field blended asphalt rubbers have been developed through the wet process to incorporate crumb rubber into the asphalt binder. Warm mix asphalt technologies have been developed to curb the problem associated with the processing and production of such crumb rubber modified binders. Also the lowered production and compaction temperatures associated with warm mix additives suggests the possibility of moisture retention in the mix, which can lead to moisture damage. Conventional moisture sensitivity tests have not effectively discriminated good and poor mixes, due to the difficulty of simulating field moisture damage mechanisms. This study was carried out to investigate performance properties of crumb rubber modified asphalt concrete, using commercial warm mix asphalt technology. Commonly utilised asphalt mixtures in North America such as dense graded and stone mastic asphalt were used in this study. Uniaxial Cyclic Compression Testing (UCCT) was used to measure permanent deformation at high temperatures. Indirect Tensile Testing (IDT) was used to investigate low temperature performance. Moisture Induced Sensitivity Testing (MiST) was proposed to be an effective method for detecting the susceptibility of asphalt mixtures to moisture damage, as it incorporates major field stripping mechanisms. Sonnewarm(TM), Sasobit(TM) and Evotherm(TM) additives improved the resistance to permanent deformation of dense graded mixes at a loading rate of 0.5 percent by weight of the binder. Polymer modified mixtures showed superior resistance to permanent deformation compared to asphalt rubber in all mix types. Rediset(TM) WMX improves low temperature properties of dense graded mixes at 0.5 percent loading on the asphalt cement. Rediset LQ and Rediset WMX showed good anti stripping properties at 0.5 percent loading on the asphalt cement. The

  5. An Additive Manufacturing Test Artifact

    PubMed Central

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

  6. An Additive Manufacturing Test Artifact.

    PubMed

    Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

    2014-01-01

    A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system.

  7. Performance tests.

    PubMed Central

    Wetherell, A

    1996-01-01

    This paper discusses the use of psychological performance tests to assess the effects of environmental stressors. The large number and the variety of performance tests are illustrated, and the differences between performance tests and other psychological tests are described in terms of their design, construction, use, and purpose. The stressor emphasis is on the effects of drugs since that is where most performance tests have found their main application, although other stressors, e.g., fatigue, toxic chemicals, are mentioned where appropriate. Diazepam is used as an example. There is no particular performance emphasis since the tests are intended to have wide applicability. However, vehicle-driving performance is discussed because it has been the subject of a great deal of research and is probably one of the most important areas of application. Performance tests are discussed in terms of the four main underlying models--factor analysis, general information processing, multiple resource and strategy models, and processing-stage models--and in terms of their psychometric properties--sensitivity, reliability, and content, criterion, construct, and face validity. Some test taxonomies are presented. Standardization is also discussed with reference to the reaction time, mathematical processing, memory search, spatial processing, unstable tracking, verbal processing, and dual task tests used in the AGARD STRES battery. Some comments on measurement strengths and appropriate study designs and methods are included. PMID:9182033

  8. Performance Testing

    NASA Technical Reports Server (NTRS)

    1991-01-01

    Systems Technology, Inc., Hawthorne, CA, developed an electronic Critical Tracking Task (CTT) system that analyzes and rates a subject's visual/motor responses for Ames Research Center. Originally applied to measuring the effects of long term confinement in the mid 1960's, the CTT system is now marketed as FACTOR 1000 by Performance Factors, Inc. Alameda, CA, under a licensing agreement with Systems Technology. The system is a non-invasive, self-administered test that takes less than a minute and detects impairment from a broad range of causes, including stress, fatigue, illness, drugs, or alcohol. It is used daily by Old Town Trolley Tours, San Diego, CA, to assess each driver's physical coordination skills prior to the start of each shift. FACTOR 1000 reduces liabilities and costs related to accidents, and costs less than one dollar per day per employee. Performance Factors is now BioFactors, Inc.

  9. The teratology testing of food additives.

    PubMed

    Barrow, Paul C; Spézia, François

    2013-01-01

    The developmental and reproductive toxicity testing (including teratogenicity) of new foods and food additives is performed worldwide according to the guidelines given in the FDA Redbook. These studies are not required for substances that are generally recognized as safe, according to the FDA inventory. The anticipated cumulated human exposure level above which developmental or reproduction studies are required depends on the structure-alert category. For food additives of concern, both developmental (prenatal) and reproduction (multigeneration) studies are required. The developmental studies are performed in two species, usually the rat and the rabbit. The reproduction study is generally performed in the rat. The two rat studies are preferably combined into a single experimental design, if possible. The test methods described in the FDA Redbook are similar to those specified by the OECD for the reproductive toxicity testing of chemicals.

  10. Diesel fuel detergent additive performance and assessment

    SciTech Connect

    Vincent, M.W.; Papachristos, M.J.; Williams, D.; Burton, J.

    1994-10-01

    Diesel fuel detergent additives are increasingly linked with high quality automotive diesel fuels. Both in Europe and in the USA, field problems associated with fuel injector coking or fouling have been experienced. In Europe indirect injection (IDI) light duty engines used in passenger cars were affected, while in the USA, a direct injection (DI) engine in heavy duty truck applications experienced field problems. In both cases, a fuel additive detergent performance test has evolved using an engine linked with the original field problem, although engine design modifications employed by the manufacturers have ensured improved operation in service. Increasing awareness of the potential for injector nozzle coking to cause deterioration in engine performance is coupled with a need to meet ever more stringent exhaust emissions legislation. These two requirements indicate that the use of detergency additives will continue to be associated with high quality diesel fuels. The paper examines detergency performance evaluated in a range of IDI and DI engines and correlates performance in the two most widely recognised test engines, namely the Peugeot 1.9 litre IDI, and Cummins L10 DI engines. 17 refs., 18 figs., 5 tabs.

  11. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  12. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  13. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  14. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 27.927 Section 27.927... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 27.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  15. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  16. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Additional tests. 29.927 Section 29.927... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Rotor Drive System § 29.927 Additional tests. (a) Any additional dynamic, endurance, and operational tests, and vibratory investigations necessary to...

  17. 78 FR 22209 - Additional Synthetic Drug Testing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-15

    ... COMMISSION 10 CFR Part 26 Additional Synthetic Drug Testing AGENCY: Nuclear Regulatory Commission. ACTION... NRC amend its Fitness for Duty program regulations to amend drug testing requirements to test for additional synthetic drugs currently not included in the regulations. The NRC determined that the...

  18. DSN system performance test software

    NASA Technical Reports Server (NTRS)

    Martin, M.

    1978-01-01

    The system performance test software is currently being modified to include additional capabilities and enhancements. Additional software programs are currently being developed for the Command Store and Forward System and the Automatic Total Recall System. The test executive is the main program. It controls the input and output of the individual test programs by routing data blocks and operator directives to those programs. It also processes data block dump requests from the operator.

  19. Tough, High-Performance, Thermoplastic Addition Polymers

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H.; Proctor, K. Mason; Gleason, John; Morgan, Cassandra; Partos, Richard

    1991-01-01

    Series of addition-type thermoplastics (ATT's) exhibit useful properties. Because of their addition curing and linear structure, ATT polymers have toughness, like thermoplastics, and easily processed, like thermosets. Work undertaken to develop chemical reaction forming stable aromatic rings in backbone of ATT polymer, combining high-temperature performance and thermo-oxidative stability with toughness and easy processibility, and minimizing or eliminating necessity for tradeoffs among properties often observed in conventional polymer syntheses.

  20. Laboratory tests of sludge-control additives

    SciTech Connect

    Tatnall, R.E.

    1996-07-01

    Laboratory {open_quotes}jar{close_quotes} tests compared eleven different fuel oil and diesel fuel sludge-control additives. Factors studied included (1) ability to disperse and prevent buildup of sludge deposits on surfaces, (2) ability to protect steel from corrosion, (3) ability to inhibit growth and proliferation of bacteria, and (4) ability to disperse water. Results varied greatly, and it was found that many commercial products do not do what they claim. It is concluded that fuel retailers should not believe manufacturers` claims for their additive products, but rather should test such products themselves to be sure that the benefits of treatment are real. A simplified form of the procedure used here is proposed as one way for dealers to do such testing.

  1. Examples Performance Testing Templates.

    SciTech Connect

    Siple, Bud H.

    2014-07-01

    The purpose of this Performance Testing Program Plan is to identify the process and phased approach that will be implemented at Site XYZ . The purpose of the testing program at Site XYZ is specifically designed to evaluate the effectiveness of systems that are employed at this site. This plan defines tasks to be accomplished to ensure that performance testing is conducted as effectively and efficiently as possible.

  2. A priori performance prediction in pharmaceutical wet granulation: testing the applicability of the nucleation regime map to a formulation with a broad size distribution and dry binder addition.

    PubMed

    Kayrak-Talay, Defne; Litster, James D

    2011-10-14

    In this study, Hapgood's nucleation regime map (Hapgood et al., 2003) was tested for a formulation that consists of an active pharmaceutical ingredient (API) of broad size distribution and a fine dry binder. Gabapentin was used as the API and hydroxypropyl cellulose (HPC) as the dry binder with deionized water as the liquid binder. The formulation was granulated in a 6l Diosna high shear granulator. The effect of liquid addition method (spray, dripping), liquid addition rate (29-245 g/min), total liquid content (2, 4 and 10%), and impeller speed (250 and 500 rpm) on the granule size distribution and lump formation were investigated. Standard methods were successfully used to characterize the process parameters (spray drop size, spray geometry and powder surface velocity) for calculating the dimensionless spray flux. However, the addition of dry binder had a very strong effect on drop penetration time that could not be predicted from simple capillary flow considerations. This is most likely due to preferential liquid penetration into the fine pores related to the dry binder particles and subsequent partial softening and dissolution of the binder. For systems containing a dry binder or other amorphous powders, it is recommended that drop penetration time be measured directly for the blended formulation and then scaled to the drop size during spraying. Using these approaches to characterize the key dimensionless groups (dimensionless spray flux and drop penetration time), Hapgood's nucleation regime map was successfully used to predict a priori the effect of process conditions on the quality of the granule size distribution as measured by lump formation and the span of the size distribution, both before and after wet massing for range of conditions studied. Wider granule size distributions and higher amount of lumps were obtained moving from intermediate to mechanical dispersion regime. Addition of the liquid in the dripping mode gave the broadest size distribution

  3. Test and Performance Anxiety

    ERIC Educational Resources Information Center

    Huberty, Thomas J.

    2010-01-01

    Test and performance anxiety is not recognized easily in schools, in large part because adolescents rarely refer themselves for emotional concerns. Not wanting to risk teasing or public attention, anxious adolescents suffer in silence and under perform on school-related tasks. In school, anxiety is experienced often by students when being…

  4. Feasibility and Testing of Additive Manufactured Components

    SciTech Connect

    Dehoff, Ryan R.; Hummelt, Ed; Solovyeva, Lyudmila

    2016-09-01

    This project focused on demonstrating the ability to fabricate two parts with different geometry: an arc flash interrupter and a hydraulic manifold. Eaton Corporation provided ORNL solid models, information related to tolerances and sensitive parameters of the parts and provided testing and evaluation. ORNL successfully manufactured both components, provided cost models of the manufacturing (materials, labor, time and post processing) and delivered test components for Eaton evaluation. The arc flash suppressor was fabricated using the Renishaw laser powder bed technology in CoCrMo while the manifold was produced from Ti-6Al-4V using the Arcam electron beam melting technology. These manufacturing techniques were selected based on the design and geometrical tolerances required. A full-scale manifold was produced on the Arcam A2 system (nearly 12 inches tall). A portion of the manifold was also produced in the Arcam Q10 system. Although a full scale manifold could not be produced in the system, a full scale manifold is expected to have similar material properties, geometric accuracy, and surface finish as could be fabricated on an Arcam Q20 system that is capable of producing four full scale manifolds in a production environment. In addition to the manifold, mechanical test specimens, geometric tolerance artifacts, and microstructure samples were produced alongside the manifold. The development and demonstration of these two key components helped Eaton understand the impact additive manufacturing can have on many of their existing products. By working within the MDF and leveraging ORNL’s manufacturing and characterization capabilities, the work will ensure the rapid insertion and commercialization of this technology.

  5. Tests of compensatory vs. additive hypotheses of mortality in mallards

    USGS Publications Warehouse

    Burnham, Kenneth P.; Anderson, David R.

    1984-01-01

    Band recovery data from over 410 000 adult Mallards (Anas platyrhynchos) banded in North America between 1950 and 1979 were analyzed to examine the effect of exploitation on annual survival rate. Two extreme hypotheses were defined: completely compensatory, and totally additive, and an explicit mathematical model was presented to represent each hypothesis. Comparison of the values of the log-likelihood functions at their maxima allowed discrimination between the two models (hypotheses). Extensive Monte Carlo studies were made on the performance of the discriminant test and the power of the test under the two extreme hypotheses and a range of intermediate hypotheses. The results of the discriminant tests on the data agreed closely with the expected performance of the test if the true underlying process was compensatory. We rejected the hypothesis of total additivity (P=.001). Instead, it appears that hunting mortalities are largely compensated for by other forms of mortality.

  6. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  7. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  8. 42 CFR 84.308 - Additional testing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... will test the eye protection's resistance to fogging in accordance with the method specified in BS EN 168:2002, Clause 16, Test for resistance to fogging of oculars. The lens shall remain free from fogging for a minimum of 8 seconds, pursuant to Clause 16. (d) The standards required in this section...

  9. Non toxic additives for improved fabric filter performance

    SciTech Connect

    Bustard, C.J.; Baldrey, K.E.; Ebner, T.G.

    1995-11-01

    The overall objective of this three-phase Small Business innovative Research (SBIR) program funded by the Department of Energy pittsburgh Energy Technology Center (PETC) is to commercialize a technology based upon the use of non-toxic, novel flue gas conditioning agents to improve particulate air toxic control and overall fabric filter performance. The ultimate objective of the Phase II program currently in progress is to demonstrate that the candidate additives are successful at full-scale on flue gas from a coal-fired utility boiler. This paper covers bench-scale field tests conducted during the period February through May, 1995. The bench-scale additives testing was conducted on a flue gas slipstream taken upstream of the existing particulate control device at a utility power plant firing a Texas lignite coal. These tests were preceded by extensive testing with additives in the laboratory using a simulated flue gas stream and re-dispersed flyash from the same power plant. The bench-scale field testing was undertaken to demonstrate the performance with actual flue gas of the bet candidate additives previously identified in the laboratory. Results from the bench-scale tests will be used to establish operating parameters for a larger-scale demonstration on either a single baghouse compartment or a full baghouse at the same site.

  10. Simple circuit performs binary addition and subtraction

    NASA Technical Reports Server (NTRS)

    Cliff, R. A.; Schaefer, D. H.

    1965-01-01

    Ripple adder reduces the number of logic circuits required to preform binary addition and subtraction. The adder uses dual input and delayed output flip-flops in one register. The contents of this register are summed with those of a standard register through conventional AND/gates.

  11. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... that the rotor drive mechanism is safe, must be performed. (b) If turbine engine torque output to the transmission can exceed the highest engine or transmission torque limit, and that output is not directly... all engines operating, make 200 applications, for 10 seconds each, of torque that is at least equal...

  12. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... that the rotor drive mechanism is safe, must be performed. (b) If turbine engine torque output to the transmission can exceed the highest engine or transmission torque rating limit, and that output is not directly... all engines operating, make 200 applications, for 10 seconds each, or torque that is at least equal...

  13. 14 CFR 27.927 - Additional tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... that the rotor drive mechanism is safe, must be performed. (b) If turbine engine torque output to the transmission can exceed the highest engine or transmission torque rating limit, and that output is not directly... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

  14. 14 CFR 29.927 - Additional tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... that the rotor drive mechanism is safe, must be performed. (b) If turbine engine torque output to the transmission can exceed the highest engine or transmission torque limit, and that output is not directly... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

  15. Electrolyte additive for improved battery performance

    DOEpatents

    Bellows, Richard J.; Kantner, Edward

    1989-04-04

    In one embodiment of the present invention, there is provided an electrochemical cell having a metal bromine couple. The cell includes an electrode structure on which to deposit the metal of the couple and a counterelectrode at which to generate bromine. A microporous membrane separates the electrode and counterelectrode. Importantly, the aqueous electrolyte comprises an aqueous metal bromide solution containing a water soluble bromine complexing agent capable of forming a water immiscible complex with bromine and an additive capable of decreasing the wettability of the microporous separators employed in such cells by such water immiscible bromine complexes.

  16. Basophil activation test with food additives in chronic urticaria patients.

    PubMed

    Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up; Chang, Yoon-Seok

    2014-01-01

    The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU.

  17. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  18. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  19. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  20. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  1. 21 CFR 660.54 - Potency tests, specificity tests, tests for heterospecific antibodies, and additional tests for...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... heterospecific antibodies, and additional tests for nonspecific properties. 660.54 Section 660.54 Food and Drugs..., specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties. The...) Specificity tests, tests for heterospecific antibodies, and additional tests for nonspecific properties....

  2. Infiniband Performance Testing

    SciTech Connect

    Minich, M

    2005-10-13

    A look at the performance of the infiniband interconnect using the Voltaire host stack. This will attempt to compare not only infiniband to other high-performance interconnects, but will also take a look at comparing some of the different hardware choices available at the time of writing (e.g. Opteron, EM64T, pci-express and pci-x).

  3. Visual acuity and test performance.

    PubMed

    Heron, E; Zytkoskee, A

    1981-02-01

    Evaluation of scholastic achievement (American College Testing Service) test scores confirms previous reports that persons with poor visual acuity perform better on these tests than individuals with normal or superior acuity.

  4. AFCATT (Anti-Fouling Chemical Additive Test Tower)

    SciTech Connect

    Philpot, E.F.; Newton, M.T.; Noble, R.T.

    1995-06-01

    Polyvinylchloride (PVC) film-type cellular fill is the fill of choice in replacing cement asbestos board fill in existing cooling towers and in new cooling towers because of its high thermal performance, ease of installation, and low initial cost. However, PVC fill has been found to foul quickly with biological and sediment material, significantly reducing tower performance and the fill`s useful life. The Anti-Fouling Chemical Additives Test Tower (AFCATT) has been build to study accumulation rates of fouling deposits in corrugated PVC film fill and to study methods of cleaning and preventing the fouling deposits. This small mechanical draft cooling tower is located next to the Unit 4 natural draft cooling tower at Georgia Power Company`s Plant Bowen. The once-through mechanical draft tower receives hot water from the condenser and returns the cold water to the basin of the host tower. The pilot tower is divided into four chambers allowing for three different treatment programs and one control to be run simultaneously. PVC fill packs are suspended from load cells to allow the weight of the fill packs to be measured continuously. Six vendors participated in the summer 1993 test program. Each proposed different methods of cleaning the fouled fill and were given the opportunity to try their proposed method of fill cleaning. To determine the success of these different treatment programs, statistical analyses were performed on the collected data and the changes in the accumulation rates compared.

  5. Uniform peanut performance test 2015

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Uniform Peanut Performance Tests (UPPT) are designed to evaluate the commercial potential of advanced breeding peanut lines not formally released. The tests are performed in ten locations across the peanut production belt. In this study, 2 controls and 13 entries were evaluated at 9 locations....

  6. Uniform peanut performance test 2013

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Uniform Peanut Performance Tests (UPPT) are designed to evaluate the commercial potential of advanced breeding peanut lines not formally released. The tests are performed in ten locations across the peanut production belt. In this study, 2 controls and 13 entries were evaluated at 9 locations....

  7. Where Lab Tests Are Performed

    MedlinePlus

    ... labs also vary in complexity, the volume of tests performed, the technology utilized, and the number and type of professionals who conduct the testing . There are important differences among the various testing settings. This information will be useful in ... Proudly sponsored by ... Learn ...

  8. Collaborative Test Reviews: Student Performance

    ERIC Educational Resources Information Center

    Bhatia, Anuradha; Makela, Carole J.

    2010-01-01

    A group study method proved helpful in improving senior-level students' performance on unit tests through collaborative learning. Students of a History of Textiles course voluntarily attended study sessions to review course content and prepare for unit tests. The students who attended the group reviews scored better on tests than those who did…

  9. Additives

    NASA Technical Reports Server (NTRS)

    Smalheer, C. V.

    1973-01-01

    The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

  10. Performance Test on Polymer Waste Form - 12137

    SciTech Connect

    Lee, Se Yup

    2012-07-01

    Polymer solidification was attempted to produce stable waste form for the boric acid concentrates and the dewatered spent resins. The polymer mixture was directly injected into the mold or drum which was packed with the boric acid concentrates and the dewatered spent resins, respectively. The waste form was produced by entirely curing the polymer mixture. A series of performance tests was conducted including compressive strength test, water immersion test, leach test, thermal stability test, irradiation stability test and biodegradation stability test for the polymer waste forms. From the results of the performance tests for the polymer waste forms, it is believed that the polymer waste form is very stable and can satisfy the acceptance criteria for permanent disposal. At present, performance tests with full scale polymer waste forms are being carried out in order to obtain qualification certificate by the regulatory institute in Korea. Polymer waste forms were prepared with the surrogate of boric acid concentrates and the surrogate of spent ion exchange resins respectively. Waste forms were also made in lab scale and in full scale. Lab. scale waste forms were directly subjected to a series of the performance tests. In the case of full scale waste form, the test specimens for the performance test were taken from a part of waste form by coring. A series of performance tests was conducted including compressive strength test, thermal stability test, irradiation stability test and biodegradation stability test, water immersion test, leach test, and free standing water for the polymer waste forms. In addition, a fire resistance test was performed on the waste forms by the requirement of the regulatory institute in Korea. Every polymer waste forms containing the boric acid concentrates and the spent ion exchange resins had exhibited excellent structural integrity of more than 27.58 MPa (4,000 psi) of compressive strength. On thermal stability testing, biodegradation

  11. Test Procedure - pumping system for caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1994-10-01

    This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

  12. Proctored and Unproctored Test Performance

    ERIC Educational Resources Information Center

    Brallier, Sara; Palm, Linda

    2015-01-01

    This study examined test performance as a function of test format (proctored versus unproctored) and course type (traditional versus distance). The participants were 246 undergraduate students who completed introductory sociology courses during four semesters at a southeastern university. During each semester, the same instructor taught a…

  13. Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

    NASA Technical Reports Server (NTRS)

    Fikes, John C.

    2014-01-01

    The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

  14. 30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. GENERAL TEST ROOM IN 1946 ADDITION, FOURTH FLOOR, LOOKING WEST. ORIGINALLY HAD SUSPENDED ACOUSTICAL CEILINGS WITH FLOURESCENT LIGHTING AND ASPHALT MASTIC TILE FLOORS - Underwriters' Laboratories, 207-231 East Ohio Street, Chicago, Cook County, IL

  15. Predicting the performance of batteries having paste additives

    SciTech Connect

    Edwards, D.B.; Cantrell, R.L.; Dayton, T.C.

    1997-12-01

    This paper discusses how models previously developed at the University of Idaho can be used to design high performance batteries containing paste additives. One model characterizes the conductivity of the active material. With this model, the influence of different additives, both conductive and nonconductive, on the capacity of paste containing these additives can be evaluated. The results of this analysis is then used in a second model to characterize the performance of cells. The models are used in the paper to help design and evaluate a battery for a hybrid electric vehicle. This design example illustrates how the models can be used to investigate unique designs for electric and hybrid electric vehicles.

  16. Uniform Peanut Performance Tests 2012

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Uniform Peanut Performance Tests (UPPT) were established in 1973 through an informal arrangement among cooperating scientists involving seven major peanut-producing states. In 1995, plant material transfer agreements were also accepted among all cooperators in the UPPT. The year 2012 completed...

  17. Friction Stir Additive Manufacturing: Route to High Structural Performance

    NASA Astrophysics Data System (ADS)

    Palanivel, S.; Sidhar, H.; Mishra, R. S.

    2015-03-01

    Aerospace and automotive industries provide the next big opportunities for additive manufacturing. Currently, the additive industry is confronted with four major challenges that have been identified in this article. These challenges need to be addressed for the additive technologies to march into new frontiers and create additional markets. Specific potential success in the transportation sectors is dependent on the ability to manufacture complicated structures with high performance. Most of the techniques used for metal-based additive manufacturing are fusion based because of their ability to fulfill the computer-aided design to component vision. Although these techniques aid in fabrication of complex shapes, achieving high structural performance is a key problem due to the liquid-solid phase transformation. In this article, friction stir additive manufacturing (FSAM) is shown as a potential solid-state process for attaining high-performance lightweight alloys for simpler geometrical applications. To illustrate FSAM as a high-performance route, manufactured builds of Mg-4Y-3Nd and AA5083 are shown as examples. In the Mg-based alloy, an average hardness of 120 HV was achieved in the built structure and was significantly higher than that of the base material (97 HV). Similarly for the Al-based alloy, compared with the base hardness of 88 HV, the average built hardness was 104 HV. A potential application of FSAM is illustrated by taking an example of a simple stiffener assembly.

  18. Metal-air cell with performance enhancing additive

    DOEpatents

    Friesen, Cody A; Buttry, Daniel

    2015-11-10

    Systems and methods drawn to an electrochemical cell comprising a low temperature ionic liquid comprising positive ions and negative ions and a performance enhancing additive added to the low temperature ionic liquid. The additive dissolves in the ionic liquid to form cations, which are coordinated with one or more negative ions forming ion complexes. The electrochemical cell also includes an air electrode configured to absorb and reduce oxygen. The ion complexes improve oxygen reduction thermodynamics and/or kinetics relative to the ionic liquid without the additive.

  19. Systematic tests for position-dependent additive shear bias

    NASA Astrophysics Data System (ADS)

    van Uitert, Edo; Schneider, Peter

    2016-11-01

    We present new tests to identify stationary position-dependent additive shear biases in weak gravitational lensing data sets. These tests are important diagnostics for currently ongoing and planned cosmic shear surveys, as such biases induce coherent shear patterns that can mimic and potentially bias the cosmic shear signal. The central idea of these tests is to determine the average ellipticity of all galaxies with shape measurements in a grid in the pixel plane. The distribution of the absolute values of these averaged ellipticities can be compared to randomised catalogues; a difference points to systematics in the data. In addition, we introduce a method to quantify the spatial correlation of the additive bias, which suppresses the contribution from cosmic shear and therefore eases the identification of a position-dependent additive shear bias in the data. We apply these tests to the publicly available shear catalogues from the Canada-France-Hawaii Telescope Lensing Survey (CFHTLenS) and the Kilo Degree Survey (KiDS) and find evidence for a small but non-negligible residual additive bias at small scales. As this residual bias is smaller than the error on the shear correlation signal at those scales, it is highly unlikely that it causes a significant bias in the published cosmic shear results of CFHTLenS. In CFHTLenS, the amplitude of this systematic signal is consistent with zero in fields where the number of stars used to model the point spread function (PSF) is higher than average, suggesting that the position-dependent additive shear bias originates from undersampled PSF variations across the image.

  20. Reflectors for SAR performance testing.

    SciTech Connect

    Doerry, Armin Walter

    2008-01-01

    Synthetic Aperture Radar (SAR) performance testing and estimation is facilitated by observing the system response to known target scene elements. Trihedral corner reflectors and other canonical targets play an important role because their Radar Cross Section (RCS) can be calculated analytically. However, reflector orientation and the proximity of the ground and mounting structures can significantly impact the accuracy and precision with which measurements can be made. These issues are examined in this report.

  1. Cascade Distiller System Performance Testing Interim Results

    NASA Technical Reports Server (NTRS)

    Callahan, Michael R.; Pensinger, Stuart; Sargusingh, Miriam J.

    2014-01-01

    The Cascade Distillation System (CDS) is a rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. Based upon the results of the 2009 distillation comparison test (DCT) and recommendations of the expert panel, the Advanced Exploration Systems (AES) Water Recovery Project (WRP) project advanced the technology by increasing reliability of the system through redesign of bearing assemblies and improved rotor dynamics. In addition, the project improved the CDS power efficiency by optimizing the thermoelectric heat pump (TeHP) and heat exchanger design. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell d International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades as compared to previous system performance. The system was challenged with Solution 1 from the NASA Exploration Life Support (ELS) distillation comparison testing performed in 2009. Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. A secondary objective of this testing is to evaluate the performance of the CDS as compared to the state of the art Distillation Assembly (DA) used in the ISS Urine Processor Assembly (UPA). This was done by challenging the system with ISS analog waste streams. This paper details the results of the AES WRP CDS performance testing.

  2. Influence of boric acid additive size on green lubricant performance.

    PubMed

    Lovell, Michael R; Kabir, M A; Menezes, Pradeep L; Higgs, C Fred

    2010-10-28

    As the industrial community moves towards green manufacturing processes, there is an increased demand for multi-functional, environmentally friendly lubricants with enhanced tribological performance. In the present investigation, green (environmentally benign) lubricant combinations were prepared by homogeneously mixing nano- (20 nm), sub-micrometre- (600 nm average size) and micrometre-scale (4 μm average size) boric acid powder additives with canola oil in a vortex generator. As a basis for comparison, lubricants of base canola oil and canola oil mixed with MoS(2) powder (ranging from 0.5 to 10 μm) were also prepared. Friction and wear experiments were carried out on the prepared lubricants using a pin-on-disc apparatus under ambient conditions. Based on the experiments, the nanoscale (20 nm) particle boric acid additive lubricants significantly outperformed all of the other lubricants with respect to frictional and wear performance. In fact, the nanoscale boric acid powder-based lubricants exhibited a wear rate more than an order of magnitude lower than the MoS(2) and larger sized boric acid additive-based lubricants. It was also discovered that the oil mixed with a combination of sub-micrometre- and micrometre-scale boric acid powder additives exhibited better friction and wear performance than the canola oil mixed with sub-micrometre- or micrometre-scale boric acid additives alone.

  3. Testing energy non-additivity in white dwarfs

    NASA Astrophysics Data System (ADS)

    Carmona, J. M.; Cortés, J. L.; Gracia-Ruiz, R.; Loret, N.

    2014-03-01

    We consider a particular effect which can be expected in scenarios of deviations from special relativity induced by Planckian physics: the loss of additivity in the total energy of a system of particles. We argue about the necessity to introduce a length scale to control the effects of non-additivity for macroscopic objects and consider white dwarfs as an appropriate laboratory to test this kind of new physics. We study the sensitivity of the mass-radius relation of the Chandrasekhar model to these corrections by comparing the output of a simple phenomenological model to observational data of white dwarfs.

  4. Tough, high performance, addition-type thermoplastic polymers

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H. (Inventor)

    1992-01-01

    A tough, high performance polyimide is provided by reacting a triple bond conjugated with an aromatic ring in a bisethynyl compound with the active double bond in a compound containing a double bond activated toward the formation of a Diels-Adler type adduct, especially a bismaleimide, a biscitraconimide, or a benzoquinone, or mixtures thereof. Addition curing of this product produces a high linear polymeric structure and heat treating the highly linear polymeric structure produces a thermally stable aromatic addition-type thermoplastic polyimide, which finds utility in the preparation of molding compounds, adhesive compositions, and polymer matrix composites.

  5. Statistical tests of additional plate boundaries from plate motion inversions

    NASA Technical Reports Server (NTRS)

    Stein, S.; Gordon, R. G.

    1984-01-01

    The application of the F-ratio test, a standard statistical technique, to the results of relative plate motion inversions has been investigated. The method tests whether the improvement in fit of the model to the data resulting from the addition of another plate to the model is greater than that expected purely by chance. This approach appears to be useful in determining whether additional plate boundaries are justified. Previous results have been confirmed favoring separate North American and South American plates with a boundary located beween 30 N and the equator. Using Chase's global relative motion data, it is shown that in addition to separate West African and Somalian plates, separate West Indian and Australian plates, with a best-fitting boundary between 70 E and 90 E, can be resolved. These results are generally consistent with the observation that the Indian plate's internal deformation extends somewhat westward of the Ninetyeast Ridge. The relative motion pole is similar to Minster and Jordan's and predicts the NW-SE compression observed in earthquake mechanisms near the Ninetyeast Ridge.

  6. 40 CFR 63.1161 - Performance testing and test methods.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Performance testing and test methods... Facilities and Hydrochloric Acid Regeneration Plants § 63.1161 Performance testing and test methods. (a) Demonstration of compliance. The owner or operator shall conduct an initial performance test for each process...

  7. Cut performance levels and testing.

    PubMed

    Bennett, Bill; Moreland, Jeff

    2011-11-01

    While the ISEA performance levels and general recommendations detailed above can help tp provide guidance when selecting hand protection products, the responsibility for testing products for specific end-user applications still rests with the end user. We can indicate, for example, that a medium-weight, uncoated Kevlar glove will typically have an ISEA cut rating of 3, but we cannot say the glove will provide the level of protection needed for the range of jobs on an automobile assembly line. Another Level 3 glove might be better suited to an application the require the worker to have an oil grip. As glove manufacturers, we know gloves. We do not know the details about every workplace. We therefore, must look to our customers to provide us the properties they need for hand protection products that will sufficiently protect their workers on the job.

  8. 40 CFR 60.8 - Performance tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of...

  9. 40 CFR 60.8 - Performance tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of...

  10. 40 CFR 60.8 - Performance tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of...

  11. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

    SciTech Connect

    Gary M. Blythe

    2006-03-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, ''Field Testing of a Wet FGD Additive.'' The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemissions of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate that the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project will conduct pilot and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosage requirements to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB co-fired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot and full-scale jet bubbling reactor (JBR) FGD systems to be tested. A third utility, to be named later, will provide the high-sulfur Eastern bituminous coal full-scale FGD test site. Degussa Corporation is providing the TMT-15 additive and technical support to the test program. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in

  12. Stereotype Threat, Test Anxiety, and Mathematics Performance

    ERIC Educational Resources Information Center

    Tempel, Tobias; Neumann, Roland

    2014-01-01

    We investigated the combined effects of stereotype threat and trait test anxiety on mathematics test performance. Stereotype threat and test anxiety interacted with each other in affecting performance. Trait test anxiety predicted performance only in a diagnostic condition that prevented stereotype threat by stereotype denial. A state measure of…

  13. 40 CFR 610.63 - Performance tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Performance tests. 610.63 Section 610... RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.63 Performance tests... 0 to 60 mph acceleration tests (at normal ambient temperatures) on the baseline...

  14. 40 CFR 610.63 - Performance tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Performance tests. 610.63 Section 610... RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.63 Performance tests... 0 to 60 mph acceleration tests (at normal ambient temperatures) on the baseline...

  15. 40 CFR 610.63 - Performance tests.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Performance tests. 610.63 Section 610... RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.63 Performance tests... 0 to 60 mph acceleration tests (at normal ambient temperatures) on the baseline...

  16. 40 CFR 610.63 - Performance tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Performance tests. 610.63 Section 610... RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.63 Performance tests... 0 to 60 mph acceleration tests (at normal ambient temperatures) on the baseline...

  17. Trinity Acceptance Tests Performance Summary.

    SciTech Connect

    Rajan, Mahesh

    2015-12-01

    Ensuring Real Applications perform well on Trinity is key to success. Four components: ASC applications, Sustained System Performance (SSP), Extra-Large MiniApplications problems, and Micro-benchmarks.

  18. Testing for Additivity at Select Mixture Groups of Interest Based on Statistical Equivalence Testing Methods

    SciTech Connect

    Stork, LeAnna M.; Gennings, Chris; Carchman, Richard; Carter, Jr., Walter H.; Pounds, Joel G.; Mumtaz, Moiz

    2006-12-01

    Several assumptions, defined and undefined, are used in the toxicity assessment of chemical mixtures. In scientific practice mixture components in the low-dose region, particularly subthreshold doses, are often assumed to behave additively (i.e., zero interaction) based on heuristic arguments. This assumption has important implications in the practice of risk assessment, but has not been experimentally tested. We have developed methodology to test for additivity in the sense of Berenbaum (Advances in Cancer Research, 1981), based on the statistical equivalence testing literature where the null hypothesis of interaction is rejected for the alternative hypothesis of additivity when data support the claim. The implication of this approach is that conclusions of additivity are made with a false positive rate controlled by the experimenter. The claim of additivity is based on prespecified additivity margins, which are chosen using expert biological judgment such that small deviations from additivity, which are not considered to be biologically important, are not statistically significant. This approach is in contrast to the usual hypothesis-testing framework that assumes additivity in the null hypothesis and rejects when there is significant evidence of interaction. In this scenario, failure to reject may be due to lack of statistical power making the claim of additivity problematic. The proposed method is illustrated in a mixture of five organophosphorus pesticides that were experimentally evaluated alone and at relevant mixing ratios. Motor activity was assessed in adult male rats following acute exposure. Four low-dose mixture groups were evaluated. Evidence of additivity is found in three of the four low-dose mixture groups.The proposed method tests for additivity of the whole mixture and does not take into account subset interactions (e.g., synergistic, antagonistic) that may have occurred and cancelled each other out.

  19. Testing and commercialization of byproduct dibasic acids as buffer additives for limestone flue gas desulfurization systems

    SciTech Connect

    Chang, J.C.S.; Mobley, J.D.

    1983-10-01

    Pilot plant (0.1 MW) tests and utility boiler full scale demonstration (194 MW) of byproduct organic dibasic acids (DBA) as buffer additives to limestone scrubbers have shown performance improvements equivalent to those achieved by the addition of pure adipic acid. Both SO/sub 2/ removal efficiency and limestone utilization increased, and no significant operating problems were observed with three of the four DBA tested. Chemical and biological evaluations of scrubber samples taken during the DBA testing indicated no detectable toxicity or mutagenicity, and no significant environmental impact is expected as a result of DBA addition. Economic estimates indicate that substitution of DBA for pure adipic acid as a buffer additive will result in additive cost savings of 30% or greater.

  20. Gasoline and Diesel Fuel Test Methods Additional Resources

    EPA Pesticide Factsheets

    Supporting documents on the Direct Final Rule that allows refiners and laboratories to use more current and improved fuel testing procedures for twelve American Society for Testing and Materials analytical test methods.

  1. Confidence and Cognitive Test Performance

    ERIC Educational Resources Information Center

    Stankov, Lazar; Lee, Jihyun

    2008-01-01

    This article examines the nature of confidence in relation to abilities, personality, and metacognition. Confidence scores were collected during the administration of Reading and Listening sections of the Test of English as a Foreign Language Internet-Based Test (TOEFL iBT) to 824 native speakers of English. Those confidence scores were correlated…

  2. Adipic gets the acid test as flue gas scrubber additive

    SciTech Connect

    Miller, I.R.

    1980-02-11

    The first full-scale demonstration of adipic acid for such use, to be conducted early in the summer of 1980 in a 200 MW power plant burning high-sulfur coal, is designed to clarify the costs and show how to reduce losses of adipic acid via degradation. Adipic acid improves SO/sub 2/ removal by acting as a buffer to limit the pH drop normally occurring at the gas-liquid interface so that the higher SO/sub 2/ concentration in the surface film improves liquid-phase mass transfer; it also promotes higher limestone utilization. Prepared by the Tennessee Valley Authority, a preliminary economic analysis for a 500 MW plant burning 4% sulfur coal indicates that the addition of 1500 ppM of adipic acid (limestone at $7/ton and the acid at $840/ton) would raise SO/sub 2/ removal from 90 to 95%, reduce the total capital investment from $41.5 to $39.5 million, and have a first year revenue requirement of $19.9 million vs. $20.9 million without the acid. The large-scale trial will also help clarify concern over unpleasant odors that have been reported at test sites of the limestone/adipic system; valeric acid has been identified as the cause.

  3. ADDITIVE TESTING FOR IMPROVED SULFUR RETENTION: PRELIMINARY REPORT

    SciTech Connect

    Amoroso, J.; Fox, K.

    2011-09-07

    The Savannah River National Laboratory is collaborating with Alfred University to evaluate the potential for additives in borosilicate glass to improve sulfur retention. This preliminary report provides further background on the incorporation of sulfur in glass and outlines the experiments that are being performed by the collaborators. A simulated waste glass composition has been selected for the experimental studies. The first phase of experimental work will evaluate the impacts of BaO, PbO, and V{sub 2}O{sub 5} at concentrations of 1.0, 2.0, and 5.0 wt % on sulfate retention in simulated high level waste borosilicate glass. The second phase of experimental work will evaluate the effects of time at the melt temperature on sulfur retention. The resulting samples will be characterized to determine the amount of sulfur remaining as well as to identify the formation of any crystalline phases. The results will be used to guide the future selection of frits and glass forming chemicals in vitrifying Department of Energy wastes containing high sulfur concentrations.

  4. 47 CFR 76.601 - Performance tests.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Performance tests. 76.601 Section 76.601... CABLE TELEVISION SERVICE Technical Standards § 76.601 Performance tests. (a) The operator of each cable... cable television system shall conduct complete performance tests of that system at least twice...

  5. 47 CFR 76.601 - Performance tests.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 4 2011-10-01 2011-10-01 false Performance tests. 76.601 Section 76.601... CABLE TELEVISION SERVICE Technical Standards § 76.601 Performance tests. (a) The operator of each cable... cable television system shall conduct complete performance tests of that system at least twice...

  6. Additional Revised Push-Up Test Norms for College Students

    ERIC Educational Resources Information Center

    Mozumdar, Arupendra; Liguori, Gary; Baumgartner, Ted A.

    2010-01-01

    The push-up test is commonly used to assess arm and shoulder girdle strength and endurance. Baumgartner, Oh, Chung, and Hales (2002) developed a revised push-up test for college students with a standardized test protocol. The purpose of the present study was to develop percentile norms for the revised push-up test based on the push-up scores of…

  7. The effect of pranayama on test anxiety and test performance

    PubMed Central

    Nemati, Azadeh

    2013-01-01

    Objectives: In an educational setting, anxiety is often experienced by students when taking a test; which is called ‘test anxiety’. This study intends to investigate the effect of doing pranayama on test anxiety and test performance. Materials and Methods: The participants consisted of 107 MA students who were randomly assigned to the control and experimental groups. The students of the experimental group practiced pranayama for one full semester. Sarason's (1980) test anxiety scale was given to both the control and experimental groups in the final session, before taking the examination. Results: After practicing pranayama, only 33% of the participants of the experimental group experienced high test anxiety, while this percentage was nearly twice in the control group (66.7%). Furthermore, the result of the t-test for test anxiety and test performance showed that the students of the experimental group had significantly lower mean test anxiety scores (M = 16.00) as compared to the students of the control group (M = 19.31). Also, the test performance scores of the experimental group were higher when compared with the control group. There was a negative correlation between the final test performance and test anxiety (r = −.204, P < .05). Conclusions: Pranayama seems to have a significant positive effect on test anxiety and test performance. It could be used as an important technique by students prior to their examinations, to reduce their test anxiety and increase their test performance. PMID:23439436

  8. The Effects of Test Anxiety on Listening Test Performance

    ERIC Educational Resources Information Center

    In'nami, Yo.

    2006-01-01

    Although decisions or inferences we make based on test scores depend both on characteristics of test-takers and of testing situations, little research has been undertaken on the effects of these characteristics on test performance (e.g., Alderson and Banerjee, 2002). This study focuses on one of the personal characteristics of test-takers, namely…

  9. Leach testing of in situ stabilization grouts containing additives to sequester contaminants

    SciTech Connect

    Serne, R.J.; Ames, L.L.; Martin, P.F.C.; LeGore, V.L.; Lindenmeier, C.W.; Phillips, S.J.

    1993-04-01

    This document discusses laboratory testing performed by Pacific Northwest Laboratory (PNL) for Westinghouse Hanford Company (WHC) of special grout formulations that incorporate specific sequestering agents to help improve the ability of the cement to resist contaminant leaching. To enhance the sequestering of contaminants we chose five additives to introduce (singly) to the control cement. The additives were Florida pebble phosphate, clinoptilolite (a natural zeolite), ferrous sulfide (a reductant), a mixed bed organic ion exchange resin and a proprietary anion-adsorbing mixed metal oxide. These additives were added one per test to the standard formulation and used to encapsulate a diluted high-salt alkaline liquid waste that is produced after various processes to remove uranium and plutonium from spent nuclear fuel. This report documents the testing of these additives.

  10. 40 CFR 63.1161 - Performance testing and test methods.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Facilities and Hydrochloric Acid Regeneration Plants § 63.1161 Performance testing and test methods. (a...) Establishment of hydrochloric acid regeneration plant operating parameters. (1) During the performance test for hydrochloric acid regeneration plants, the owner or operator shall establish site-specific operating...

  11. PNNI Performance Validation Test Report

    NASA Technical Reports Server (NTRS)

    Dimond, Robert P.

    1999-01-01

    Two Private Network-Network Interface (PNNI) neighboring peers were monitored with a protocol analyzer to understand and document how PNNI works with regards to initialization and recovery processes. With the processes documented, pertinent events were found and measured to determine the protocols behavior in several environments, which consisted of congestion and/or delay. Subsequent testing of the protocol in these environments was conducted to determine the protocol's suitability for use in satellite-terrestrial network architectures.

  12. Low-Temperature Additive Performance in Jet A Fuels

    DTIC Science & Technology

    2013-04-01

    flowability -improving additive developed in the JP-8+100 LT program was studied for use in Jet A fuels. The results indicate that the LT additive does...improve the flowability of near specification maximum freeze point (FP) Jet A fuels (near -40 °C) when employed at a concentration of 2,000 mg/L to a... flowability equivalent to near specification maximum FP JP-8 fuels (near -47 °C). Viscosity measurements demonstrated that the LT additive

  13. The Squad Performance Test Bed

    DTIC Science & Technology

    2014-06-01

    7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Army, ARDEC, Target Behavioral Response Laboratory,RDAR-EIQ-SD,Building 3518, Picatinny Arsenal,NJ...K; DeMarco, R; Reidener, J. Active Shooter Training Evaluation: West Orange Police Department (TBRL-WOASTR- 14-001). Picatinny Arsenal, NJ: Target...Master title style UNCLASSIFIED Questions? US Army - Target Behavioral Response Lab Mr. Gladstone V. Reid Jr. Picatinny Arsenal, NJ

  14. 14 CFR 43.15 - Additional performance rules for inspections.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... TRANSPORTATION AIRCRAFT MAINTENANCE, PREVENTIVE MAINTENANCE, REBUILDING, AND ALTERATION § 43.15 Additional... inspect the following systems in accordance with the maintenance manual or Instructions for...

  15. 14 CFR 43.15 - Additional performance rules for inspections.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... TRANSPORTATION AIRCRAFT MAINTENANCE, PREVENTIVE MAINTENANCE, REBUILDING, AND ALTERATION § 43.15 Additional... inspect the following systems in accordance with the maintenance manual or Instructions for...

  16. 14 CFR 43.15 - Additional performance rules for inspections.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... TRANSPORTATION AIRCRAFT MAINTENANCE, PREVENTIVE MAINTENANCE, REBUILDING, AND ALTERATION § 43.15 Additional... inspect the following systems in accordance with the maintenance manual or Instructions for...

  17. 14 CFR 43.15 - Additional performance rules for inspections.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... TRANSPORTATION AIRCRAFT MAINTENANCE, PREVENTIVE MAINTENANCE, REBUILDING, AND ALTERATION § 43.15 Additional... inspect the following systems in accordance with the maintenance manual or Instructions for...

  18. 14 CFR 43.15 - Additional performance rules for inspections.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... TRANSPORTATION AIRCRAFT MAINTENANCE, PREVENTIVE MAINTENANCE, REBUILDING, AND ALTERATION § 43.15 Additional... inspect the following systems in accordance with the maintenance manual or Instructions for...

  19. Astronaut Scott Carpenter tests balance mechanism performance

    NASA Technical Reports Server (NTRS)

    1961-01-01

    Astronaut M. Scott Carpenter's balance mechanism performance is tested by his walking on a narrow board in his bare feet. He is performing this test at the School of Aviation Medicine, Pensicola, Florida (04570); Carpenter walks a straight line by putting one foot directly in front of the other to test his balance (04571).

  20. Slug tests in wells screened across the water table: some additional considerations.

    PubMed

    Butler, J J

    2014-01-01

    The majority of slug tests done at sites of shallow groundwater contamination are performed in wells screened across the water table and are affected by mechanisms beyond those considered in the standard slug-test models. These additional mechanisms give rise to a number of practical issues that are yet to be fully resolved; four of these are addressed here. The wells in which slug tests are performed were rarely installed for that purpose, so the well design can result in problematic (small signal to noise ratio) test data. The suitability of a particular well design should thus always be assessed prior to field testing. In slug tests of short duration, it can be difficult to identify which portion of the test represents filter-pack drainage and which represents formation response; application of a mass balance can help confirm that test phases have been correctly identified. A key parameter required for all slug test models is the casing radius. However, in this setting, the effective casing radius (borehole radius corrected for filter-pack porosity), not the nominal well radius, is required; this effective radius is best estimated directly from test data. Finally, although conventional slug-test models do not consider filter-pack drainage, these models will yield reasonable hydraulic conductivity estimates when applied to the formation-response phase of a test from an appropriately developed well.

  1. 40 CFR 63.1161 - Performance testing and test methods.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Facilities and Hydrochloric Acid Regeneration Plants § 63.1161 Performance testing and test methods. (a...) or measure the concentration of HCl (and Cl2 for hydrochloric acid regeneration plants) in gases... to the initial test or tests. (c) Establishment of hydrochloric acid regeneration plant...

  2. The improvement of rechargeable lithium battery electrolyte performance with additives

    NASA Technical Reports Server (NTRS)

    Dominey, L. A.; Goldman, J. L.

    1990-01-01

    The deliberate introduction of additives like 2-methylfuran (2-MeF) is known to improve Li cycleability in cyclic ether electrolytes. The authors found that the proclivity of 2-MeF to polymerize in the bulk electrolyte or on a TiS2 cathode was inhibited by the addition of reduced oxygen species, such as O2- and OH-. Additionally, the polymerization of tetrahydrofuran and dioxolane and the destructive processes initiated by AsF6- decomposition to AsF5 and AsF3 were inhibited by the introduction of reduced oxygen species, particularly OH- at the 10-ppm to 100-ppm level.

  3. Test Anxiety, Test Comfort and Student Achievement Test Performance.

    ERIC Educational Resources Information Center

    Fyans, Leslie J., Jr.

    The Illinois Inventory of Educational Progress (IIEP) Test Comfort Scale was administered and test results were studied in terms of student achievement and correlates of achievement. Using the revised, seven-item scale, it was determined that: in grade 4, there was no main significant effect for sex or ethnic differences, although Orientals and…

  4. Tribological performance of nanoparticles as lubricating oil additives

    NASA Astrophysics Data System (ADS)

    Gulzar, M.; Masjuki, H. H.; Kalam, M. A.; Varman, M.; Zulkifli, N. W. M.; Mufti, R. A.; Zahid, Rehan

    2016-08-01

    The prospect of modern tribology has been expanded with the advent of nanomaterial-based lubrication systems, whose development was facilitated by the nanotechnology in recent years. In literature, a variety of nanoparticles have been used as lubricant additives with potentially interesting friction and wear properties. To date, although there has been a great deal of experimental research on nanoparticles as lubricating oil additives, many aspects of their tribological behavior are yet to be fully understood. With growing number of possibilities, the key question is: what types of nanoparticles act as a better lubricating oil additive and why? To answer this question, this paper reviews main types of nanoparticles that have been used as lubricants additives and outlines the mechanisms by which they are currently believed to function. Significant aspects of their tribological behavior such as dispersion stability and morphology are also highlighted.

  5. Enhanced electrochemical performance of monoclinic WO3 thin film with redox additive aqueous electrolyte.

    PubMed

    Shinde, Pragati A; Lokhande, Vaibhav C; Chodankar, Nilesh R; Ji, Taeksoo; Kim, Jin Hyeok; Lokhande, Chandrakant D

    2016-12-01

    To achieve the highest electrochemical performance for supercapacitor, it is very essential to find out a suitable pair of an active electrode material and an electrolyte. In the present work, a simple approach is employed to enhance the supercapacitor performance of WO3 thin film. The WO3 thin film is prepared by a simple and cost effective chemical bath deposition method and its electrochemical performance is tested in conventional (H2SO4) and redox additive [H2SO4+hydroquinone (HQ)] electrolytes. Two-fold increment in electrochemical performance for WO3 thin film is observed in redox additive aqueous electrolyte compared to conventional electrolyte. WO3 thin film showed maximum specific capacitance of 725Fg(-1), energy density of 25.18Whkg(-1) at current density of 7mAcm(-2) with better cycling stability in redox electrolyte. This strategy provides the versatile way for designing the high performance energy storage devices.

  6. Performance test procedures for thermal collectors - Outdoor testing

    NASA Astrophysics Data System (ADS)

    Gillett, W. B.

    A review of outdoor solar collector test methods is presented, based largely on the CEC Recommendations for European Solar Collector Test Methods. Test facility design and instrumentation are discussed, with reference to their influence on measured collector efficiencies. Steady state outdoor testing, mixed indoor/outdoor testing and transient testing are reviewed, and it is concluded that although the testing of simple flat plate water heaters is fairly well understood, more work is now required to develop test methods for the new high performance collectors which are coming onto the market.

  7. Integrated Performance Testing Workshop, Modules 6 - 11

    SciTech Connect

    Leach, Janice; Torres, Teresa M.

    2012-10-01

    These modules cover performance testing of: Interior Detection Systems; Access Controls; Exterior Detection Systems; Video Assessment Systems; SNM / Contraband Detection Systems; Access Delay Elements

  8. 40 CFR 63.1161 - Performance testing and test methods.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... section. An owner or operator may conduct multiple performance tests to establish alternative compliant... owner or operator may conduct multiple performance tests to establish alternative compliant operating... moisture content of the stack gas; and (v) Method 26A, “Determination of Hydrogen Halide and...

  9. Large-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Daniel, Richard C.; Gauglitz, Phillip A.; Burns, Carolyn A.; Fountain, Matthew S.; Shimskey, Rick W.; Billing, Justin M.; Bontha, Jagannadha R.; Kurath, Dean E.; Jenks, Jeromy WJ; MacFarlan, Paul J.; Mahoney, Lenna A.

    2013-08-01

    One of the events postulated in the hazard analysis for the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak event involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids that behave as a Newtonian fluid. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and in processing facilities across the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are mostly absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale testing. The small-scale testing and resultant data are described in Mahoney et al. (2012b), and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used

  10. Effects of Video Games as Reinforcers for Computerized Addition Performance.

    ERIC Educational Resources Information Center

    Axelrod, Saul; And Others

    1987-01-01

    Four 2nd-grade students completed addition problems on a computer, using video games as reinforcers. Two variable ratio schedules of reinforcement failed to increase student accuracy or the rate of correct responses. In a no-games reinforcement condition, students had more opportunities to respond and had a greater number of correct answers.…

  11. EP Additive Performance in Biobased vs. Paraffinic Base Oils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A series of commercial extreme pressure (EP) additives containing sulfur, phosphorus, and chlorine were investigated for their EP properties in soybean (SBO) and paraffinic (PRFN) base oils. The investigations were conducted using a 4-ball (4B) and twist-compression (TC) tribometers. The concentra...

  12. Small-Scale Spray Releases: Additional Aerosol Test Results

    SciTech Connect

    Schonewill, Philip P.; Gauglitz, Phillip A.; Kimura, Marcia L.; Brown, G. N.; Mahoney, Lenna A.; Tran, Diana N.; Burns, Carolyn A.; Kurath, Dean E.

    2013-08-01

    One of the events postulated in the hazard analysis at the Waste Treatment and Immobilization Plant (WTP) and other U.S. Department of Energy (DOE) nuclear facilities is a breach in process piping that produces aerosols with droplet sizes in the respirable range. The current approach for predicting the size and concentration of aerosols produced in a spray leak involves extrapolating from correlations reported in the literature. These correlations are based on results obtained from small engineered spray nozzles using pure liquids with Newtonian fluid behavior. The narrow ranges of physical properties on which the correlations are based do not cover the wide range of slurries and viscous materials that will be processed in the WTP and across processing facilities in the DOE complex. To expand the data set upon which the WTP accident and safety analyses were based, an aerosol spray leak testing program was conducted by Pacific Northwest National Laboratory (PNNL). PNNL’s test program addressed two key technical areas to improve the WTP methodology (Larson and Allen 2010). The first technical area was to quantify the role of slurry particles in small breaches where slurry particles may plug the hole and prevent high-pressure sprays. The results from an effort to address this first technical area can be found in Mahoney et al. (2012a). The second technical area was to determine aerosol droplet size distribution and total droplet volume from prototypic breaches and fluids, including sprays from larger breaches and sprays of slurries for which literature data are largely absent. To address the second technical area, the testing program collected aerosol generation data at two scales, commonly referred to as small-scale and large-scale. The small-scale testing and resultant data are described in Mahoney et al. (2012b) and the large-scale testing and resultant data are presented in Schonewill et al. (2012). In tests at both scales, simulants were used to mimic the

  13. Automated microbial metabolism laboratory. [design of advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into test chambers

    NASA Technical Reports Server (NTRS)

    1974-01-01

    The design and rationale of an advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into each of four test chambers are outlined. The feasibility for multiple addition tests was established and various details of the methodology were studied. The four chamber battery of tests include: (1) determination of the effect of various atmospheric gases and selection of that gas which produces an optimum response; (2) determination of the effect of incubation temperature and selection of the optimum temperature for performing Martian biochemical tests; (3) sterile soil is dosed with a battery of C-14 labeled substrates and subjected to experimental temperature range; and (4) determination of the possible inhibitory effects of water on Martian organisms is performed initially by dosing with 0.01 ml and 0.5 ml of medium, respectively. A series of specifically labeled substrates are then added to obtain patterns in metabolic 14CO2 (C-14)O2 evolution.

  14. 40 CFR 63.1333 - Additional requirements for performance testing.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... from continuous process vent i as calculated using the procedures specified in § 63.116(c)(4), kg/month. PPM = Amount of polymer produced in one month as determined by the procedures specified in § 63.1318(b... specified in § 63.11(b)(6); and (3) Determine the exit velocity using the techniques specified in...

  15. 40 CFR 63.1333 - Additional requirements for performance testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... National Emission Standards for Hazardous Air Pollutant Emissions: Group IV Polymers and Resins § 63.1333... paragraphs (b)(1) and (b)(2) of this section. ER19JN00.041 Where: ERMBS = Emission rate of organic HAP or TOC from continuous process vents, kg/Mg product. Ei = Emission rate of organic HAP or TOC from...

  16. 40 CFR 63.504 - Additional requirements for performance testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... National Emission Standards for Hazardous Air Pollutant Emissions: Group I Polymers and Resins § 63.504... reduction or outlet organic HAP or TOC concentration. If a compliance demonstration has been...

  17. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... requested, this documentation shall be provided to the Administrator. (2) When the General Provisions' data analysis, recordkeeping, and reporting requirements in § 63.7(g) refer to the Notification of Compliance... date with the Administrator (or delegated State or local agency) by mutual agreement. (b) Data shall...

  18. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... requested, this documentation shall be provided to the Administrator. (2) When the General Provisions' data analysis, recordkeeping, and reporting requirements in § 63.7(g) refer to the Notification of Compliance... date with the Administrator (or delegated State or local agency) by mutual agreement. (b) Data shall...

  19. 40 CFR 63.1437 - Additional requirements for performance testing.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... requested, this documentation shall be provided to the Administrator. (2) When the General Provisions' data analysis, recordkeeping, and reporting requirements in § 63.7(g) refer to the Notification of Compliance... date with the Administrator (or delegated State or local agency) by mutual agreement. (b) Data shall...

  20. A PERFORMANCE TEST OF TEACHING EFFECTIVENESS.

    ERIC Educational Resources Information Center

    BAKER, EVA L.; POPHAM, V. JAMES

    THIS REPORT DESCRIBES THE INITIAL VALIDATION OF PERFORMANCE TESTS OF TEACHER EFFECTIVENESS--USING PUPIL GAINS AS THE CRITERION OF EFFECTIVENESS--AND THE STEPS TAKEN IN RECOGNITION OF THE PROPRIETY OF SUCH MEASURES ONLY IF ALL TEACHERS ARE TEACHING FOR THE SAME OBJECTIVES. AS A FIRST STEP, IT WAS HYPOTHESIZED THAT A VALID PERFORMANCE TEST OF…

  1. Perform Ultrasonic Testing on Cs Capsule Overpacks

    SciTech Connect

    DAVIS, S.J.

    2000-04-06

    This procedure provides a safe, uniform method for the performance of the ultrasonic weld inspection of the Cesium capsule overpacks. The inspection system will detect cracks, lack of fusion, and lack of penetration. This computer controlled automated system will perform the examination once the capsule overpack has been placed in the pool cell. Examination of the capsule overpacks will be in accordance with drawing H-283014, REV. 0 ,and a certified NDE examiner will perform the test procedure, provide analysis, and test documentation.

  2. Testcross additive and dominance effects in best linear unbiased prediction of maize single-cross performance.

    PubMed

    Bernardo, R

    1996-11-01

    Best linear unbiased prediction (BLUP) has been found to be useful in maize (Zea mays L.) breeding. The advantage of including both testcross additive and dominance effects (Intralocus Model) in BLUP, rather than only testcross additive effects (Additive Model), has not been clearly demonstrated. The objective of this study was to compare the usefulness of Intralocus and Additive Models for BLUP of maize single-cross performance. Multilocation data from 1990 to 1995 were obtained from the hybrid testing program of Limagrain Genetics. Grain yield, moisture, stalk lodging, and root lodging of untested single crosses were predicted from (1) the performance of tested single crosses and (2) known genetic relationships among the parental inbreds. Correlations between predicted and observed performance were obtained with a delete-one cross-validation procedure. For the Intralocus Model, the correlations ranged from 0.50 to 0.66 for yield, 0.88 to 0.94 for moisture, 0.47 to 0.69 for stalk lodging, and 0.31 to 0.45 for root lodging. The BLUP procedure was consistently more effective with the Intralocus Model than with the Additive Model. When the Additive Model was used instead of the Intralocus Model, the reductions in the correlation were largest for root lodging (0.06-0.35), smallest for moisture (0.00-0.02), and intermediate for yield (0.02-0.06) and stalk lodging (0.02-0.08). The ratio of dominance variance (v D) to total genetic variance (v G) was highest for root lodging (0.47) and lowest for moisture (0.10). The Additive Model may be used if prior information indicates that VD for a given trait has little contribution to VG. Otherwise, the continued use of the Intralocus Model for BLUP of single-cross performance is recommended.

  3. Experimental Tests of Cooling: Expectations and Additional Needs

    SciTech Connect

    Zisman, Michael S

    2008-09-24

    Cooling is a critical aspect for a high-performance Neutrino Factory or a MuonCollider. For this reason, considerable effort is being put toward theexperimental verification of this technique. The international Muon IonizationCooling Experiment, MICE, was approved to operate at Rutherford AppletonLaboratory (RAL) in the UK and beam line commissioning commenced in March, 2008. The MICE collaboration comprises about 130 scientists and engineers from Asia, Europe, and the U.S. In this paper we present the motivation and goals for thisexperiment and describe its present status. MICE is scheduled for completion in2011. We will also indicate the prospects for a future 6D muon coolingexperiment and discuss its possible time schedule.

  4. Assessing Differential Item Functioning in Performance Tests.

    ERIC Educational Resources Information Center

    Zwick, Rebecca; And Others

    Although the belief has been expressed that performance assessments are intrinsically more fair than multiple-choice measures, some forms of performance assessment may in fact be more likely than conventional tests to tap construct-irrelevant factors. As performance assessment grows in popularity, it will be increasingly important to monitor the…

  5. Performance analysis of flexible DSSC with binder addition

    NASA Astrophysics Data System (ADS)

    Muliani, Lia; Hidayat, Jojo; Anggraini, Putri Nur

    2016-04-01

    Flexible DSSC is one of modification of DSSC based on its substrate. Operating at low temperature, flexible DSSC requires a binder to improve particles interconnection. This research was done to compare the morphology and performance of flexible DSSC that was produced with binder-added and binder-free. TiO2 powder, butanol, and HCl were mixed for preparation of TiO2 paste. Small amount of titanium isopropoxide as binder was added into the mixture. TiO2 paste was deposited on ITO-PET plastic substrate with area of 1x1 cm2 by doctor blade method. Furthermore, SEM, XRD, and BET characterization were done to analyze morphology and surface area of the TiO2 photoelectrode microstructures. Dyed TiO2 photoelectrode and platinum counter electrode were assembled and injected by electrolyte. In the last process, flexible DSSCs were illuminated by sun simulator to do J-V measurement. As a result, flexible DSSC containing binder showed higher performance with photoconversion efficiency of 0.31%.

  6. Does performing drop jumps with additional eccentric loading improve jump performance?

    PubMed

    Aboodarda, Saied J; Byrne, Jeannette M; Samson, Michael; Wilson, Barry D; Mokhtar, Abdul H; Behm, David G

    2014-08-01

    Previous investigators have speculated that applying additional external load throughout the eccentric phase of the jumping movement could amplify the stretch-shortening cycle mechanism and modulate jumping performance and jump exercise intensity. The aims of this study, therefore, were to determine the effect of increased eccentric phase loading, as delivered using an elastic device, on drop jumps (DJs) performed from different drop heights. Of specific interest were changes in (a) the kinetics; eccentric and concentric impulse, rate of force development (RFD), concentric velocity and (b) the electromyographic (EMG) activity of leg muscles. In a randomized repeated-measure study, 15 highly resistance trained male subjects performed DJs from 3 heights (20, 35, and 50 cm) under 3 different conditions: body weight only (free DJ) and with elastic bands providing downward force equivalent to 20% (+20% DJ) and 30% (+30% DJ) of body mass. All DJs were recorded using video and force plate data that were synchronized with EMG data. Results demonstrated that using additional tensile load during the airborne and eccentric phases of the DJ could enhance eccentric impulse (p = 0.042) and RFD (p < 0.001) and resulted in small to moderate effect size (ES) increases in quadriceps intergrated EMG across the eccentric phase (0.23 > ES > 0.51). The observed greater eccentric loading, however, did not immediately alter concentric kinetics and jump height nor did it alter muscle activation levels during this phase. The findings indicated that, in addition to the conventional technique of increasing drop height, using a tensile load during the airborne and eccentric phases of the DJ could further improve eccentric loading of DJs. As it has been suggested that eccentric impulse and RFD are indicators of DJ exercise intensity, these findings suggest that the loaded DJs, using additional elastic load, may be an effective technique for improving DJ exercise intensity without acute effects

  7. SI PC104 Performance Test Report

    SciTech Connect

    Montelongo, S

    2005-12-16

    The Spectral Instruments (SI) PC104 systems associated with the SI-1000 CCD camera exhibited intermittent power problems during setup, test and operations which called for further evaluation and testing. The SI PC104 System is the interface between the SI-1000 CCD camera and its associated Diagnostic Controller (DC). As such, the SI PC104 must be a reliable, robust system capable of providing consistent performance in various configurations and operating conditions. This SI PC104 system consists of a stackable set of modules designed to meet the PC104+ Industry Standard. The SI PC104 System consists of a CPU module, SI Camera card, Media converter card, Video card and a I/O module. The root cause of power problems was identified as failing solder joints at the LEMO power connector attached to the SI Camera Card. The recommended solution was to provide power to the PC104 system via a PC104+ power supply module configured into the PC104 stack instead of thru the LEMO power connector. Test plans (2) were developed to test SI PC104 performance and identify any outstanding issues noted during extended operations. Test Plan 1 included performance and image acquisition tests. Test Plan 2 verified performance after implementing recommendations. Test Plan 2 also included verifying integrity of system files and driver installation after bootup. Each test plan was implemented to fully test against each set of problems noted. Test Plan presentations and Test Plan results are attached as appendices. Anticipated test results will show successful operation and reliable performance of the SI PC104 system receiving its power via a PC104 power supply module. A SI PC104 Usage Recommendation Memo will be sent out to the SI PC104 User Community. Recommendation memo(s) are attached as appendices.

  8. Sizing up systems: researchers to test performance measures.

    PubMed

    Anderson, H J

    1991-10-20

    Researchers are preparing to test 81 possible performance indicators that health care systems can use to more thoroughly measure how well they are carrying out their missions. In addition to measurements of financial performance and quality, the indicators cover such areas as community service and customer satisfaction.

  9. Integrated Performance Testing for Nonproliferation Support Project

    SciTech Connect

    Johns, Russell; Bultz, Garl Alan; Byers, Kenneth R.; Yaegle, William

    2013-08-20

    The objective of this workshop is to provide participants with training in testing techniques and methodologies for assessment of the performance of: Physical Protection system elements; Material Control and Accounting (MC&A) system elements.

  10. Performance Testing in Electronic Technology. Final Report.

    ERIC Educational Resources Information Center

    Williamson, Bert; Pedersen, Joe F.

    This set of 21 performance tests in electronics technology was developed on the basis of a review of commercial and noncommercial instructional materials dealing with electronics technology. The tests, which were reviewed by a group of community college instructors and an advisory committee for electronics technology, address the following…

  11. Laboratory Performance Testing of Residential Dehumidifiers (Presentation)

    SciTech Connect

    Winkler, J.

    2012-03-01

    Six residential vapor compression cycle dehumidifiers spanning the available range of capacities and efficiencies were tested in the National Renewable Energy Laboratory's Heating, Ventilating, and Air-Conditioning Systems Laboratory. Each was tested under a wide range of indoor air conditions to facilitate the development of performance curves for use in whole-building simulation tools.

  12. Primer Stepper Motor Nomenclature, Definition, Performance and Recommended Test Methods

    NASA Technical Reports Server (NTRS)

    Starin, Scott; Shea, Cutter

    2014-01-01

    There has been an unfortunate lack of standardization of the terms and components of stepper motor performance, requirements definition, application of torque margin and implementation of test methods. This paper will address these inconsistencies and discuss in detail the implications of performance parameters, affects of load inertia, control electronics, operational resonances and recommended test methods. Additionally, this paper will recommend parameters for defining and specifying stepper motor actuators. A useful description of terms as well as consolidated equations and recommended requirements is included.

  13. Laboratory endurance testing of a 25/75 sunflower oil-diesel fuel blend treated with fuel additives

    SciTech Connect

    Ziejewski, M.; Kaufman, K.R.; Tupa, R.C.

    1984-01-01

    The engine performance and durability effects of a barium smoke suppressant additive, Lubrizol 565, and an ashless polymeric additive, Lubrizol 552, in a 25-75 blend (v/v) of alkali refined sunflower oil with diesel fuel were investigated. The study was performed on a direct injected, turbocharged, and intercooled diesel engine. These additives were tested in an attempt to reduce carbon buildup problems observed while using an untreated 25-75 blend of sunflower oil and diesel fuel.

  14. Design and performance test of spacecraft test and operation software

    NASA Astrophysics Data System (ADS)

    Wang, Guohua; Cui, Yan; Wang, Shuo; Meng, Xiaofeng

    2011-06-01

    Main test processor (MTP) software is the key element of Electrical Ground Support Equipment (EGSE) for spacecraft test and operation used in the Chinese Academy of Space Technology (CAST) for years without innovation. With the increasing demand for a more efficient and agile MTP software, the new MTP software was developed. It adopts layered and plug-in based software architecture, whose core runtime server provides message queue management, share memory management and process management services and forms the framework for a configurable and open architecture system. To investigate the MTP software's performance, the test case of network response time, test sequence management capability and data-processing capability was introduced in detail. Test results show that the MTP software is common and has higher performance than the legacy one.

  15. 47 CFR 76.601 - Performance tests.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... specified subscriber terminals may be required by the Commission or the local franchiser to secure...-performance test points chosen shall be balanced to represent all geographic areas served by the cable system... network: Provided, that data shall be included to relate the measured performance of the system as...

  16. 47 CFR 76.601 - Performance tests.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... specified subscriber terminals may be required by the Commission or the local franchiser to secure...-performance test points chosen shall be balanced to represent all geographic areas served by the cable system... network: Provided, that data shall be included to relate the measured performance of the system as...

  17. 47 CFR 76.601 - Performance tests.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... specified subscriber terminals may be required by the Commission or the local franchiser to secure...-performance test points chosen shall be balanced to represent all geographic areas served by the cable system... network: Provided, that data shall be included to relate the measured performance of the system as...

  18. RHIC sextant test: Accelerator systems and performance

    SciTech Connect

    Pilat, F.; Trbojevic, D.; Ahrens, L.

    1997-08-01

    One sextant of the RHIC Collider was commissioned in early 1997 with beam. We describe here the performance of the accelerator systems, instrumentation subsystems and application software. We also describe a ramping test without beam that took place after the commissioning with beam. Finally, we analyze the implications of accelerator systems performance and their impact on the planning for RHIC installation and commissioning.

  19. MEGARA: large pupil element tests and performance

    NASA Astrophysics Data System (ADS)

    Martínez-Delgado, I.; Sánchez-Blanco, E.; Pérez-Calpena, A.; García-Vargas, M. L.; Maldonado, X. M.; Gil de Paz, A.; Carrasco, E.; Gallego, J.; Iglesias-Páramo, J.; Sánchez-Moreno, F. M.

    2016-07-01

    MEGARA is a third generation spectrograph for the Spanish 10.4m telescope (GTC) providing two observing modes: a large central Integral Field Unit (IFU), called the Large Compact Bundle (LCB), covering a FOV of 12.5 × 11.3 arcsec2, and a Multi-Object Spectrograph (MOS) with a FOV of 3.5 × 3.5 arcmin2. MEGARA will observe the whole visible range from 3650A to 10000A allowing different spectral resolutions (low, medium and high) with R = 6000, 11000 and 18000 respectively. The dispersive elements are placed at the spectrograph pupil position in the path of the collimated beam and they are composed of a set of volume phase hologram gratings (VPHs) sandwiched between two flat windows and coupled in addition to two prisms in the case of the medium- and high-resolution units. We will describe the tests and setups developed to check the requirements of all units, as well as the obtained performance at laboratory

  20. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Additional tests for Type A packagings designed...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must...

  1. Performance Test for the SIGMA Communication System

    NASA Astrophysics Data System (ADS)

    Jeong, Seonyeong; Lee, Hyojeong; Lee, Seongwhan; Shin, Jehyuck; Lee, Jungkyu; Jin, Ho

    2016-12-01

    Scientific CubeSat with Instruments for Global Magnetic Fields and Radiations (SIGMA) is a 3-U size CubeSat that will be operated in low earth orbit (LEO). The SIGMA communication system uses a very high frequency (VHF) band for uplink and an ultra high frequency (UHF) band for downlink. Both frequencies belong to an amateur band. The ground station that communicates with SIGMA is located at Kyung Hee Astronomical Observatory (KHAO). For reliable communication, we carried out a laboratory (LAB) test and far-field tests between the CubeSat and a ground station. In the field test, we considered test parameters such as attenuation, antenna deployment, CubeSat body attitude, and Doppler frequency shift in transmitting commands and receiving data. In this paper, we present a communication performance test of SIGMA, a link budget analysis, and a field test process. We also compare the link budget with the field test results of transmitting commands and receiving data.

  2. Impact of Educational Level on Performance on Auditory Processing Tests

    PubMed Central

    Murphy, Cristina F. B.; Rabelo, Camila M.; Silagi, Marcela L.; Mansur, Letícia L.; Schochat, Eliane

    2016-01-01

    Research has demonstrated that a higher level of education is associated with better performance on cognitive tests among middle-aged and elderly people. However, the effects of education on auditory processing skills have not yet been evaluated. Previous demonstrations of sensory-cognitive interactions in the aging process indicate the potential importance of this topic. Therefore, the primary purpose of this study was to investigate the performance of middle-aged and elderly people with different levels of formal education on auditory processing tests. A total of 177 adults with no evidence of cognitive, psychological or neurological conditions took part in the research. The participants completed a series of auditory assessments, including dichotic digit, frequency pattern and speech-in-noise tests. A working memory test was also performed to investigate the extent to which auditory processing and cognitive performance were associated. The results demonstrated positive but weak correlations between years of schooling and performance on all of the tests applied. The factor “years of schooling” was also one of the best predictors of frequency pattern and speech-in-noise test performance. Additionally, performance on the working memory, frequency pattern and dichotic digit tests was also correlated, suggesting that the influence of educational level on auditory processing performance might be associated with the cognitive demand of the auditory processing tests rather than auditory sensory aspects itself. Longitudinal research is required to investigate the causal relationship between educational level and auditory processing skills. PMID:27013958

  3. Performance testing of feedwater pump turbines

    SciTech Connect

    Finck, E.J.

    1980-01-01

    Utilities acknowledge that steam turbine drives for feedwater pumps outperform motor drives in improving station heat rate. Rising fuel prices frequently make steam costs the determining factor in evaluating feedwater pump drive turbines. Decisions made on efficiency differences as small as 0.2 percent often necessitate accurate performance testing to verify quoted efficiencies, making it imperative that accurate tests of turbine throttle flow, shaft speed and torque, and other parameters be run to ensure meaningful results. A highly specialized feed pump turbine manufacturers test facility is the most accurate testing method as well as the most convenient and potentially the most economical. 4 figures.

  4. 76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-31

    ... AGENCY 40 CFR Part 80 RIN 2060-AP17 Regulation of Fuel and Fuel Additives: Alternative Test Method for... correlated to the fuel parameter's respective EPA designated test method. These alternative test methods are... sections 114(a) and 301(a) of the CAA. Regulation of Fuel and Fuel Additives: Alternative Test Method...

  5. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a...) Since some analytes may deteriorate during storage, detected levels of the drug below the...

  6. 49 CFR 199.111 - Retention of samples and additional testing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.111 Retention of samples and additional testing. (a...) Since some analytes may deteriorate during storage, detected levels of the drug below the...

  7. Virtual Shaker Testing: Simulation Technology Improves Vibration Test Performance

    NASA Technical Reports Server (NTRS)

    Ricci, Stefano; Peeters, Bart; Fetter, Rebecca; Boland, Doug; Debille, Jan

    2008-01-01

    In the field of vibration testing, the interaction between the structure being tested and the instrumentation hardware used to perform the test is a critical issue. This is particularly true when testing massive structures (e.g. satellites), because due to physical design and manufacturing limits, the dynamics of the testing facility often couples with the test specimen one in the frequency range of interest. A further issue in this field is the standard use of a closed loop real-time vibration control scheme, which could potentially shift poles and change damping of the aforementioned coupled system. Virtual shaker testing is a novel approach to deal with these issues. It means performing a simulation which closely represents the real vibration test on the specific facility by taking into account all parameters which might impact the dynamic behavior of the specimen. In this paper, such a virtual shaker testing approach is developed. It consists of the following components: (1) Either a physical-based or an equation-based coupled electro-mechanical lumped parameter shaker model is created. The model parameters are obtained from manufacturer's specifications or by carrying out some dedicated experiments; (2) Existing real-time vibration control algorithm are ported to the virtual simulation environment; and (3) A structural model of the test object is created and after defining proper interface conditions structural modes are computed by means of the well-established Craig-Bampton CMS technique. At this stage, a virtual shaker test has been run, by coupling the three described models (shaker, control loop, structure) in a co-simulation routine. Numerical results have eventually been correlated with experimental ones in order to assess the robustness of the proposed methodology.

  8. Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

    NASA Technical Reports Server (NTRS)

    Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

    2012-01-01

    Many approaches have been considered in an effort to improve the regression rate of solid fuels for hybrid rocket applications. One promising method is to use a fuel with a fast burning rate such as paraffin wax; however, additional performance increases to the fuel regression rate are necessary to make the fuel a viable candidate to replace current launch propulsion systems. The addition of energetic and/or nano-sized particles is one way to increase mass-burning rates of the solid fuels and increase the overall performance of the hybrid rocket motor.1,2 Several paraffin-based fuel grains with various energetic additives (e.g., lithium aluminum hydride (LiAlH4) have been cast in an attempt to improve regression rates. There are two major advantages to introducing LiAlH4 additive into the solid fuel matrix: 1) the increased characteristic velocity, 2) decreased dependency of Isp on oxidizer-to-fuel ratio. The testing and characterization of these solid-fuel grains have shown that continued work is necessary to eliminate unburned/unreacted fuel in downstream sections of the test apparatus.3 Changes to the fuel matrix include higher melting point wax and smaller energetic additive particles. The reduction in particle size through various methods can result in more homogeneous grain structure. The higher melting point wax can serve to reduce the melt-layer thickness, allowing the LiAlH4 particles to react closer to the burning surface, thus increasing the heat feedback rate and fuel regression rate. In addition to the formulation of LiAlH4 and paraffin wax solid-fuel grains, liquid additives of triethylaluminum and diisobutylaluminum hydride will be included in this study. Another promising fuel formulation consideration is to incorporate a small percentage of RDX as an additive to paraffin. A novel casting technique will be used by dissolving RDX in a solvent to crystallize the energetic additive. After dissolving the RDX in a solvent chosen for its compatibility

  9. 20 CFR 666.110 - May a Governor require additional indicators of performance?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false May a Governor require additional indicators... of Performance § 666.110 May a Governor require additional indicators of performance? Yes, Governors may develop additional indicators of performance for adults, youth and dislocated worker...

  10. 20 CFR 666.110 - May a Governor require additional indicators of performance?

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false May a Governor require additional indicators... of Performance § 666.110 May a Governor require additional indicators of performance? Yes, Governors may develop additional indicators of performance for adults, youth and dislocated worker...

  11. Halogen occultation experiment (HALOE) performance verification test procedure

    NASA Technical Reports Server (NTRS)

    Mauldin, L. E., III

    1986-01-01

    The Performance Verification Test Procedure is given for the Halogen Occultation Experiment (HALOE) instrument, which is being developed in house at the Langley Research Center for the Upper Atmosphere Research Satellite (UARS). This procedure is used for comprehensive performance testing of the HALOE instrument which occurs before, during, and after flight environmental tests. The radiometric performance tests include noise, drift, linearity, instantaneous field-of-view, cal wheel gas cell characterization, and self thermal emissions. Pointer/tracker performance tests include sun sensor performance, gimbal performance, control system performance, and boresight alignment. In addition, the instrument is tested functionally in simulated orbit sequences and all command operating modes are exercised. The data analysis required for each test is specified and pass/fail criteria are given where applicable. This test will fully demonstrate the HALOE instrument's ability to achieve science mission requirements. The HALOE instrument is a gas correlation radiometer that measures vertical distribution of eight upper atmospheric constituents: O3, HCl, HF, NO, CH4, H2O, NO2, and CO2.

  12. Thermal Performance Testing of Cryogenic Insulation Systems

    NASA Technical Reports Server (NTRS)

    Fesmire, James E.; Augustynowicz, Stan D.; Scholtens, Brekke E.

    2007-01-01

    Efficient methods for characterizing thermal performance of materials under cryogenic and vacuum conditions have been developed. These methods provide thermal conductivity data on materials under actual-use conditions and are complementary to established methods. The actual-use environment of full temperature difference in combination with vacuum-pressure is essential for understanding insulation system performance. Test articles include solids, foams, powders, layered blankets, composite panels, and other materials. Test methodology and apparatus design for several insulation test cryostats are discussed. The measurement principle is liquid nitrogen boil-off calorimetry. Heat flux capability ranges from approximately 0.5 to 500 watts per square meter; corresponding apparent thermal conductivity values range from below 0.01 up to about 60 mW/m- K. Example data for different insulation materials are also presented. Upon further standardization work, these patented insulation test cryostats can be available to industry for a wide range of practical applications.

  13. Comparison of the tribology performance of nano-diesel soot and graphite particles as lubricant additives

    NASA Astrophysics Data System (ADS)

    Zhang, Zu-chuan; Cai, Zhen-bing; Peng, Jin-fang; Zhu, Min-hao

    2016-02-01

    The tribology behavior of exhaust diesel soot as a lubricant additive was investigated and then compared with that of a selection of commercial nano-graphite particles. Specifically, 0.01 wt% particles were dispersed in PAO4 oil with 1 wt% sorbitan monooleate (Span 80) as a dispersing agent, and wear tests based on the ball against plate mode were conducted at various temperatures. Different analytical techniques (e.g. transmission electron, scanning electron and infrared microscopy; energy dispersive x-ray and Raman spectroscopy; and charge measurement) were employed to characterize the chemistry and morphology of the additives and their tribology performance. The oil containing only 0.01 wt% diesel soot clearly improved wear resistance over 60 °C. In particular, at 100 °C the wear rate decreased by approximately 90% compared to the function of base oil. In the same test conditions, diesel soot exhibited better anti-wear performance than nano-graphite at high temperatures. The potential measure showed that the nano-graphite had positive charge and the diesel soot had negative charge. Electrochemical action may play an important role in the lubricant mechanisms of diesel soot and graphite as oil additives.

  14. Neuropsychological test performance in illiterate subjects.

    PubMed

    Ostrosky-Solis, F; Ardila, A; Rosselli, M; Lopez-Arango, G; Uriel-Mendoza, V

    1998-10-01

    The purpose of this study was to further analyze the effects of education across different age ranges on neuropsychological test performance. Two different analyses were performed. The first analysis was conducted in order to pinpoint the impact of school attendance on neuropsychological testing. A group of 64 illiterate normal subjects was selected in the Mexican Republic. Their performance was compared with two barely schooled control groups (1-2 and 3-4 years of schooling). The subjects' ages ranged from 16 to 85 years. In the second analysis, the illiterate subjects were further matched by age and sex with individuals with 1 to 4, 5 to 9, and 10 to 19 years of formal education. The Spanish version of the NEUROPSI neuropsychological test battery (Ostrosky, Ardila, & Rosselli, 1997) was used. Results indicated a significant educational effect on most of the tests. Largest educational effect was noted in constructional abilities (copying of a figure), language (comprehension), phonological verbal fluency, and conceptual functions (similarities, calculation abilities, and sequences). Aging effect was noted in visuoperceptual (visual detection) and memory scores. In the first subject sample, it was evident that, despite using such limited educational range (from 0-4 years of formal education), and such a wide age range (from 16-85 years), schooling represented a stronger variable than age. It is proposed that education effect on neuropsychological test performance represents a negatively accelerated curve, tending to a plateau.

  15. Load responsive multilayer insulation performance testing

    NASA Astrophysics Data System (ADS)

    Dye, S.; Kopelove, A.; Mills, G. L.

    2014-01-01

    Cryogenic insulation designed to operate at various pressures from one atmosphere to vacuum, with high thermal performance and light weight, is needed for cryogenically fueled space launch vehicles and aircraft. Multilayer insulation (MLI) performs well in a high vacuum, but the required vacuum shell for use in the atmosphere is heavy. Spray-on foam insulation (SOFI) is often used in these systems because of its light weight, but can have a higher heat flux than desired. We report on the continued development of Load Responsive Multilayer Insulation (LRMLI), an advanced thermal insulation system that uses dynamic beam discrete spacers that provide high thermal performance both in atmosphere and vacuum. LRMLI consists of layers of thermal radiation barriers separated and supported by micromolded polymer spacers. The spacers have low thermal conductance, and self-support a thin, lightweight vacuum shell that provides internal high vacuum in the insulation. The dynamic load responsive spacers compress to support the external load of a vacuum shell in one atmosphere, and decompress under reduced atmospheric pressure for lower heat leak. Structural load testing was performed on the spacers with various configurations. LRMLI was installed on a 400 liter tank and boil off testing with liquid nitrogen performed at various chamber pressures from one atmosphere to high vacuum. Testing was also performed with an MLI blanket on the outside of the LRMLI.

  16. Load responsive multilayer insulation performance testing

    SciTech Connect

    Dye, S.; Kopelove, A.; Mills, G. L.

    2014-01-29

    Cryogenic insulation designed to operate at various pressures from one atmosphere to vacuum, with high thermal performance and light weight, is needed for cryogenically fueled space launch vehicles and aircraft. Multilayer insulation (MLI) performs well in a high vacuum, but the required vacuum shell for use in the atmosphere is heavy. Spray-on foam insulation (SOFI) is often used in these systems because of its light weight, but can have a higher heat flux than desired. We report on the continued development of Load Responsive Multilayer Insulation (LRMLI), an advanced thermal insulation system that uses dynamic beam discrete spacers that provide high thermal performance both in atmosphere and vacuum. LRMLI consists of layers of thermal radiation barriers separated and supported by micromolded polymer spacers. The spacers have low thermal conductance, and self-support a thin, lightweight vacuum shell that provides internal high vacuum in the insulation. The dynamic load responsive spacers compress to support the external load of a vacuum shell in one atmosphere, and decompress under reduced atmospheric pressure for lower heat leak. Structural load testing was performed on the spacers with various configurations. LRMLI was installed on a 400 liter tank and boil off testing with liquid nitrogen performed at various chamber pressures from one atmosphere to high vacuum. Testing was also performed with an MLI blanket on the outside of the LRMLI.

  17. BepiColombo Laser Altimeter performance tests

    NASA Astrophysics Data System (ADS)

    Gouman, J.; Thomas, N.; Marti, K. S.; Beck, T.; Péteut, A.; Pommerol, A.

    2014-04-01

    The first European laser altimeter designed for interplanetary flight, BELA (BepiColombo Laser Altimeter) is ready to be integrated on the BepiColombo spacecraft to be launched to Mercury in July 2016 [1]. The flight instrument is currently installed in its calibration laboratory at the University of Bern where it is being tested to assess its performance. This abstract describes the different tests, run using data from Mercury and the Moon. Results on these ongoing tests will be presented in detail at the conference.

  18. SAS molecular tests Salmonella detection kit. Performance tested method 021202.

    PubMed

    Bapanpally, Chandra; Montier, Laura; Khan, Shah; Kasra, Akif; Brunelle, Sharon L

    2014-01-01

    The SAS Molecular tests Salmonella Detection method, a Loop-mediated Isothermal Amplification method, performed as well as or better than the U.S. Department of Agriculture-Food Safety Inspection Service Microbiology Laboratory Guidebook and the U.S. Food and Drug Administration Bacteriological Analytical Manual reference methods for ground beef, beef trim, ground turkey, chicken carcass rinses, bagged mixed lettuce, and fresh spinach. The ground beef (30% fat, 25 g test portion), poultry matrixes and leafy greens were validated in a 6-7 h enrichment, and ground beef (30% fat, 375 g composite test portion) and beef trim (375 g composite test portion) were validated in a 16-20 h enrichment. The method performance for meat and leafy green matrixes was shown to be acceptable under conditions of co-enrichment with Escherichia coli 0157. Thus, after a short 6-7 h co-enrichment step, ground beef, beef trim, lettuce, and spinach can be tested for both Salmonella and E. coli O157. Inclusivity and exclusivity testing revealed no false negatives and no false positives among the 100 Salmonella serovars and 30 non-Salmonella species examined. The method was shown to be robust when enrichment time, DNA extract hold time, and DNA volume were varied.

  19. Sulfur-free lignins from alkaline pulping tested in mortar for use as mortar additives.

    PubMed

    Nadif, A; Hunkeler, D; Käuper, P

    2002-08-01

    Sulfur-free lignin, obtained through the acid precipitation of black liquor from the soda pulping process, has been tested as water reducer in mortar. It has also been compared to existing commercial additives such as naphthalene sulfonates and lignosulfonates. The ash content and sugar content of these lignins are low in comparison to lignosulfonates, conferring on them higher purity. A procedure for small scale testing derived from the industrial norms SN-EN196 and ASTM (Designation C230-90) is presented. Specifically, all the sulfur-free lignins tested improved the flow of the mortar. Selected flax lignins performed better than lignosulfonates though still less than naphthalene sulfonates. Furthermore, certain hemp lignins gave comparable results to the lignosulfonates. Overall, the straw lignin prepared herein is comparable in performance to commercially available lignins, such as Organocell, Alcell and Curan 100. The plant from which the lignin was isolated, and the process of the pulp mill are the primary influences on the performance of the lignin.

  20. A performance benchmark test for geodynamo simulations

    NASA Astrophysics Data System (ADS)

    Matsui, H.; Heien, E. M.

    2013-12-01

    In the last ten years, a number of numerical dynamo models have successfully represented basic characteristics of the geomagnetic field. As new models and numerical methods continue to be developed, it is important to update and extend benchmarks for testing these models. The first dynamo benchmark of Christensen et al. (2001) was applied to models based on spherical harmonic expansion methods. However, only a few groups have reported results of the dynamo benchmark using local methods (Harder and Hansen, 2005; Matsui and Okuda, 2005; Chan et al., 2007) because of the difficulty treating magnetic boundary conditions based on the local methods. On the other hand, spherical harmonics expansion methods perform poorly on massively parallel computers because global data communications are required for the spherical harmonics expansions to evaluate nonlinear terms. We perform benchmark tests to asses various numerical methods for the next generation of geodynamo simulations. The purpose of this benchmark test is to assess numerical geodynamo models on a massively parallel computational platform. To compare among many numerical methods as possible, we consider the model with the insulated magnetic boundary by Christensen et al. (2001) and with the pseudo vacuum magnetic boundary, because the pseudo vacuum boundaries are implemented easier by using the local method than the magnetic insulated boundaries. In the present study, we consider two kinds of benchmarks, so-called accuracy benchmark and performance benchmark. In the accuracy benchmark, we compare the dynamo models by using modest Ekman and Rayleigh numbers proposed by Christensen et. al. (2001). We investigate a required spatial resolution for each dynamo code to obtain less than 1% difference from the suggested solution of the benchmark test using the two magnetic boundary conditions. In the performance benchmark, we investigate computational performance under the same computational environment. We perform these

  1. Earthquake early warning performance tests for Istanbul

    NASA Astrophysics Data System (ADS)

    Köhler, N.; Wenzel, F.; Erdik, M.; Alcik, H.; Mert, A.

    2009-04-01

    The Marmara Region is the most densily populated region in Turkey. The greater area of the mega-city Istanbul inhabits about 14 million people. The city is located in the direct vicinity of the Main Marmara Fault, a dextral strike-slip fault system intersecting the Sea of Marmara, which is the western continuation of the North Anatolian Fault [Le Pichon et al., 2001]. Its closest distance to the city of Istanbul ranges between 15 and 20 km. Recent estimates by Parsons [2004] give a probability of more than 40% of a M ≥ 7 earthquake that will affect Istanbul within the next 30 years. Due to this high seismic risk, earthquake early warning is an important task in disaster management and seismic risk reduction, increasing the safety of millions of people living in and around Istanbul and reducing economic losses. The Istanbul Earthquake Rapid Response and Early Warning System (IERREWS) includes a set of 10 strong-motion sensors used for early warning which are installed between Istanbul and the Main Marmara Fault. The system works on the exceedance of amplitude thresholds, whereas three alarm levels are defined at three different thresholds [Erdik et al., 2003]. In the context of the research project EDIM (Earthquake Disaster Information System for the Marmara Region, Turkey), the early warning network is planned to be extended by an additional set of 10 strong-motion sensors installed around the Sea of Marmara to include the greater Marmara Region into the early warning process. We present performance tests of both the existing and the planned extended early warning network using ground motion simulations for 280 synthetic earthquakes along the Main Marmara Fault with moment magnitudes between 4.5 and 7.5. We apply the amplitude thresholds of IERREWS, as well as, for comparison, an early warning algorithm based on artificial neural networks which estimates hypocentral location and magnitude of the occurring earthquake. The estimates are updated continuously with

  2. Small-Scale Performance Testing for Studying New Explosives

    SciTech Connect

    Gagliardi, F J; Chambers, R D; Tran, T D

    2005-04-29

    The development of new high-explosive (HE) formulations involves characterizing their safety and performance. Small-scale experiments requiring only a small amount of explosives are of interest because they can facilitate development while minimizing hazards and reducing cost. A detonation-spreading, dent test, called the Floret test, was designed to obtain performance data for new explosives. It utilizes the detonation of about a 1.0 g sample of HE, initiated by an accelerated aluminum flyer. Upon impact, the HE sample detonates and a copper witness plate absorbs the ensuing shock wave. The dent of the plate is then measured and correlated to the energetic output of the HE. Additionally, the dent measurement can be used to compare the performance of different explosives. The Floret test is beneficial because it quickly returns important performance information, while requiring only a small explosive sample. This work will explain the Floret test and discuss some exemplary results.

  3. Motivation and Test Anxiety in Test Performance across Three Testing Contexts: The CAEL, CET, and GEPT

    ERIC Educational Resources Information Center

    Cheng, Liying; Klinger, Don; Fox, Janna; Doe, Christine; Jin, Yan; Wu, Jessica

    2014-01-01

    This study examined test-takers' motivation, test anxiety, and test performance across a range of social and educational contexts in three high-stakes language tests: the Canadian Academic English Language (CAEL) Assessment in Canada, the College English Test (CET) in the People's Republic of China, and the General English Proficiency Test (GEPT)…

  4. A Litmus Test for Performance Assessment.

    ERIC Educational Resources Information Center

    Finson, Kevin D.; Beaver, John B.

    1992-01-01

    Presents 10 guidelines for developing performance-based assessment items. Presents a sample activity developed from the guidelines. The activity tests students ability to observe, classify, and infer, using red and blue litmus paper, a pH-range finder, vinegar, ammonia, an unknown solution, distilled water, and paper towels. (PR)

  5. Thermal Performance Testing of EMU and CSAFE Liquid Cooling Garments

    NASA Technical Reports Server (NTRS)

    Rhodes, Richard; Bue, Grant; Hakam, Mark; Radford, Tamara

    2013-01-01

    Future exploration missions require the development of a new liquid cooling garment (LCG) that offers greater system reliability, is more comfortable, and maximizes thermal performance. To inform the development of a future LCG a thermal performance test was conducted to evaluate three factors: (1) the effect of the thermal comfort undergarment (TCU) on tactile and thermal comfort, (2) the comparable thermal performance of an CSAFE developed engineering evaluation unit (EEU) LCG, which uses a commercial-off-the-shelf (COTS) wicking garment as the base, and (3) the performance of a torso or upper body only LCG configuration to evaluate a proposed auxiliary loop configuration. To evaluate the thermal performance of each configuration a metabolic suit test was conducted, utilizing suited subjects to generate metabolic heat by walking on a treadmill at various speeds. Three (3) test subjects of similar height and weight produced a metabolic load for five tests by either resting (300-600 BTU/hr), walking at a slow pace (1200 BTU/hr), and walking at a brisk pace (2200 BTU/hr). During the test, data was collected that would allow us to track the heat transfer to the LCG and ventilation system to determine the thermal performance of the LCG configurations. Four different test configurations were tested, with one configuration tested twice. The test results show that the CSAFE EEU LCG and EMU LCG had comparable performance. The testing also showed that an auxiliary loop LCG, sized similarly to the shirt-only configuration, should provide adequate cooling for contingency scenarios. Finally, the testing showed the previous analysis that assumed a UA deterioration from the TCU was too conservative and the TCU may prove to be acceptable for future development with additional analysis and testing.

  6. Event-related potential practice effects on the Paced Auditory Serial Addition Test (PASAT)

    PubMed Central

    Rogers, Jeffrey M.; Fox, Alison M.

    2012-01-01

    Practice can change the nature and quality of a stimulus-response relationship. The current study observed the effects of repeated administration of the Paced Auditory Serial Addition Test (PASAT) in 12 healthy individuals, in an effort to establish distinct profiles associated with novel and practiced processing. Over four training sessions the mean number of correct responses on this demanding test of attention significantly improved and was approaching ceiling for most task conditions. Behavioural improvements were associated with significantly reduced amplitude of late Processing Negativity, a frontally distributed component of the event-related potential waveform associated with voluntary, limited-capacity activity within higher-order attentional systems. These results suggest that PASAT performance became more efficient as practice seemingly eased the strategic planning and coordination requirements the task places on frontally-mediated executive attention resources. The findings of the current study extend our understanding of the functional and behavioural mechanisms underlying the effects of practice. PMID:23717344

  7. Thermal Performance Testing of EMU and CSAFE Liquid Cooling Gannents

    NASA Technical Reports Server (NTRS)

    Rhodes, Richard; Bue, Grant; Meginnis, Ian; Hakam, Mary; Radford, Tamara

    2013-01-01

    Future exploration missions require the development of a new liquid cooling garment (LCG) to support the next generation extravehicular activity (EVA) suit system. The new LCG must offer greater system reliability, optimal thermal performance as required by mission directive, and meet other design requirements including improved tactile comfort. To advance the development of a future LCG, a thermal performance test was conducted to evaluate: (1) the comparable thermal performance of the EMU LCG and the CSAFE developed engineering evaluation unit (EEU) LCG, (2) the effect of the thermal comfort undergarment (TCU) on the EMU LCG tactile and thermal comfort, and (3) the performance of a torso or upper body only LCG shirt to evaluate a proposed auxiliary loop. To evaluate the thermal performance of each configuration, a metabolic test was conducted using the Demonstrator Spacesuit to create a relevant test environment. Three (3) male test subjects of similar height and weight walked on a treadmill at various speeds to produce three different metabolic loads - resting (300-600 BTU/hr), walking at a slow pace (1200 BTU/hr), and walking at a brisk pace (2200 BTU/hr). Each subject participated in five tests - two wearing the CSAFE full LCG, one wearing the EMU LCG without TCUs, one wearing the EMU LCG with TCUs, and one with the CSAFE shirt-only. During the test, performance data for the breathing air and cooling water systems and subject specific data was collected to define the thermal performance of the configurations. The test results show that the CSAFE EEU LCG and EMU LCG with TCU had comparable performance. The testing also showed that an auxiliary loop LCG, sized similarly to the shirt-only configuration, should provide adequate cooling for contingency scenarios. Finally, the testing showed that the TCU did not significantly hinder LCG heat transfer, and may prove to be acceptable for future suit use with additional analysis and testing.

  8. Thermal Performance Testing Of Cryogenic Piping Systems

    NASA Technical Reports Server (NTRS)

    Fesmire, J. E.; Augustynowicz, S. D.; Nagy, Z. F.

    2003-01-01

    Thermal performance measurement of piping systems under actual field conditions is important for space launch development and commercial industry. Knowledge of the true insulating effectiveness is needed in system design, development, and research activities. A new 18-meter-long test apparatus for cryogenic pipelines has been developed. Three different pipelines, rigid or flexible, can be tested simultaneously. Critical factors in heat leak measurements include eliminating heat transfer at end connections and obtaining proper liquid saturation condition. Effects due to variations in the external ambient conditions like wind, humidity, and solar radiation must be minimized. The static method of liquid nitrogen evaporation has been demonstrated, but the apparatus can be adapted for dynamic testing with cryogens, chilled water, or other working fluids. This technology is suited for the development of an industry standard test apparatus and method. Examples of the heat transfer data from testing commercially available pipelines are given. Prototype pipelines are currently being tested and evaluated at the Cryogenics Test Laboratory of NASA Kennedy Space Center.

  9. Sensitization to Food Additives in Patients with Allergy: A Study Based on Skin Test and Open Oral Challenge.

    PubMed

    Moghtaderi, Mozhgan; Hejrati, Zinatosadat; Dehghani, Zahra; Dehghani, Faranak; Kolahi, Niloofar

    2016-06-01

    There has been a great increase in the consumption of various food additives in recent years. The purpose of this study was to identify the incidence of sensitization to food additives by using skin prick test in patients with allergy and to determine the concordance rate between positive skin tests and oral challenge in hypersensitivity to additives. This cross-sectional study included 125 (female 71, male 54) patients aged 2-76 years with allergy and 100 healthy individuals. Skin tests were performed in both patient and control groups with 25 fresh food additives. Among patients with allergy, 22.4% showed positive skin test at least to one of the applied materials. Skin test was negative to all tested food additives in control group. Oral food challenge was done in 28 patients with positive skin test, in whom 9 patients showed reaction to culprit (Concordance rate=32.1%). The present study suggested that about one-third of allergic patients with positive reaction to food additives showed positive oral challenge; it may be considered the potential utility of skin test to identify the role of food additives in patients with allergy.

  10. Fast Flux Test Facility core restraint system performance

    SciTech Connect

    Hecht, S.L.; Trenchard, R.G.

    1990-02-01

    Characterizing Fast Flux Test Facility (FFTF) core restraint system performance has been ongoing since the first operating cycle. Characterization consists of prerun analysis for each core load, in-reactor and postirradiation measurements of subassembly withdrawal loads and deformations, and using measurement data to fine tune predictive models. Monitoring FFTF operations and performing trend analysis has made it possible to gain insight into core restraint system performance and head off refueling difficulties while maximizing component lifetimes. Additionally, valuable information for improved designs and operating methods has been obtained. Focus is on past operating experience, emphasizing performance improvements and avoidance of potential problems. 4 refs., 12 figs., 2 tabs.

  11. RHIC Sextant Test - Accelerator Systems and Performance

    NASA Astrophysics Data System (ADS)

    Pilat, F.; Ahrens, L.; Brown, K.; Connolly, R.; dell, G. F.; Fischer, W.; Kewisch, J.; Mackay, W.; Mane, V.; Peggs, S.; Satogata, T.; Tepikian, S.; Thompson, P.; Trbojevic, D.; Tsoupas, N.; Wei, J.

    1997-05-01

    One sextant of the RHIC collider and the full AtR (AGS to RHIC) transfer line have been commissioned in early 1997 with beam. We describe here the design and performance of the accelerator systems during the test, such as the magnet and power supply systems, instrumentation subsystems and application software. After reviewing the main milestones of the commissioning we describe a ramping test without beam that took place after the commissioning with beam. Finally, we analyze the implications of accelerator systems preformance and their impact on the plannig for RHIC installation and commissioning.

  12. Performance tests of large thin vacuum windows

    SciTech Connect

    Hall Crannell

    2011-02-01

    Tests of thin composition vacuum windows of the type used for the Tagger in Hall B at the Thomas Jefferson National Accelerator Facility are described. Three different tests have been performed. These include: (1) measurement of the deformation and durability of a window under long term (>8 years) almost continuous vacuum load, (2) measurement of the deformation as a function of flexing of the window as it is cycled between vacuum and atmosphere, and (3) measurement of the relative diffusion rate of gas through a variety of thin window membranes.

  13. Testing Solutions for Adult Film Performers.

    PubMed

    Bergman, Zachary R

    2014-01-01

    The majority of the nation's adult films are produced in California, and within California, most production occurs in Los Angeles. In order to regulate that content, the County of Los Angeles passed the Safer Sex in the Adult Film Industry Act (Measure B) by way of referendum in November 2012. Measure B requires that adult film producers wishing to film in Los Angeles County obtain permits from the Los Angeles County Department of Public Health, and it also mandates that adult film performers use condoms while filming and "engaging in anal or vaginal sexual intercourse." Nevertheless, between August 2013 and January 2014, several adult film performers in California tested positive for HIV, and the threat of infection remains. Although Measure B is not the best way forward for Los Angeles County, elements of the ordinance should be incorporated into future legislative efforts. Given the economic ramifications of industry flight due to more localized regulations, this Note concludes that California should pass statewide comprehensive reform. Any such new legislation must treat "independent contractors," the classification generally used for adult film performs, as if they were regular employees. Legislation should also couple mandatory testing mechanisms with provisions granting performers the right to choose whether they use condoms. Finally, legislation must include mechanisms that ensure performers' preferences are not improperly tainted by outside forces and pressures. While there will always be risks associated with the production of adult content, if undertaken, these reforms could significantly mitigate those hazards.

  14. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2012-07-01 2012-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  15. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2011-07-01 2011-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  16. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2013-07-01 2013-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  17. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... validity as promulgated in the Standards for Educational and Psychological Testing; (ii) Provide test... 34 Education 3 2014-07-01 2014-07-01 false Additional criteria for the approval of certain tests... of Independently Administered Tests; Specification of Passing Score; Approval of State Process §...

  18. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    SciTech Connect

    Gary Blythe

    2007-05-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing

  19. RHIC Sextant Test -- Physics and performance

    SciTech Connect

    Wei, J.; Fischer, W.; Ahrens, L.

    1997-07-01

    This paper presents beam physics and machine performance results of the Relativistic Heavy Ion Collider (RHIC) Sextant and AGS-to-RHIC (AtR) transfer line during the Sextant Test in early 1997. Techniques used to measure both machine properties (difference orbits, dispersion, and beamline optics) and beam parameters (energy, intensity, transverse and longitudinal emittances) are described. Good agreement was achieved between measured and design lattice optics. The gold ion beam quality was shown to approach RHIC design requirements.

  20. Testing Devices Garner Data on Insulation Performance

    NASA Technical Reports Server (NTRS)

    2014-01-01

    To develop a test instrument that could garner measurements of the thermal performance of insulation under extreme conditions, researchers at Kennedy Space Center devised the Cryostat 1 and then Cryostat 2. McLean, Virginia-based QinetiQ North America licensed the technology and plans to market it to organizations developing materials for things like piping and storage tank insulation, refrigeration, appliances, and consumer goods.

  1. Flight test of takeoff performance monitoring system

    NASA Technical Reports Server (NTRS)

    Middleton, David B.; Srivatsan, Raghavachari; Person, Lee H., Jr.

    1994-01-01

    The Takeoff Performance Monitoring System (TOPMS) is a computer software and hardware graphics system that visually displays current runway position, acceleration performance, engine status, and other situation advisory information to aid pilots in their decision to continue or to abort a takeoff. The system was developed at the Langley Research Center using the fixed-base Transport Systems Research Vehicle (TSRV) simulator. (The TSRV is a highly modified Boeing 737-100 research airplane.) Several versions of the TOPMS displays were evaluated on the TSRV B-737 simulator by more than 40 research, United States Air Force, airline and industry and pilots who rated the system satisfactory and recommended further development and testing. In this study, the TOPMS was flight tested on the TSRV. A total of 55 takeoff and 30 abort situations were investigated at 5 airfields. TOPMS displays were observed on the navigation display screen in the TSRV research flight deck during various nominal and off-nominal situations, including normal takeoffs; reduced-throttle takeoffs; induced-acceleration deficiencies; simulated-engine failures; and several gross-weight, runway-geometry, runway-surface, and ambient conditions. All tests were performed on dry runways. The TOPMS software executed accurately during the flight tests and the displays correctly depicted the various test conditions. Evaluation pilots found the displays easy to monitor and understand. The algorithm provides pretakeoff predictions of the nominal distances that are needed to accelerate the airplane to takeoff speed and to brake it to a stop; these predictions agreed reasonably well with corresponding values measured during several fully executed and aborted takeoffs. The TOPMS is operational and has been retained on the TSRV for general use and demonstration.

  2. MEMS performance challenges: packaging and shock tests

    NASA Astrophysics Data System (ADS)

    Chang, Jiyoung; Yang, Chen; Zhang, Bin; Lin, Liwei

    2011-06-01

    This paper describes recent advances in the MEMS performance challenges with emphases on packaging and shock tests. In the packaging area, metal to metal bonding processes have been developed to overcome limitations of the glass frit bonding by means of two specific methods: (1) pre-reflow of solder for enhanced bonding adhesion, and (2) the insertion of thin metal layer between parent metal bonding materials. In the shock test area, multiscale analysis for a MEMS package system has been developed with experimental verifications to investigate dynamic responses under drop-shock tests. Structural deformation and stress distribution data are extracted and predicted for device fracture and in-operation stiction analyses for micro mechanical components in various MEMS sensors, including accelerometers and gyroscopes.

  3. Acceptance test report: Field test of mixer pump for 241-AN-107 caustic addition project

    SciTech Connect

    Leshikar, G.A.

    1997-05-16

    The field acceptance test of a 75 HP mixer pump (Hazleton serial number N-20801) installed in Tank 241-AN-107 was conducted from October 1995 thru February 1996. The objectives defined in the acceptance test were successfully met, with two exceptions recorded. The acceptance test encompassed field verification of mixer pump turntable rotation set-up and operation, verification that the pump instrumentation functions within established limits, facilitation of baseline data collection from the mixer pump mounted ultrasonic instrumentation, verification of mixer pump water flush system operation and validation of a procedure for its operation, and several brief test runs (bump) of the mixer pump.

  4. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  5. 30 CFR 75.151 - Tests for methane; qualified person; additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; qualified person; additional... Certified Persons § 75.151 Tests for methane; qualified person; additional requirement. Notwithstanding the... methane unless he demonstrates to the satisfaction of an authorized representative of the Secretary...

  6. 42 CFR 493.1421 - Condition: Laboratories performing moderate complexity testing; testing personnel.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... complexity testing; testing personnel. 493.1421 Section 493.1421 Public Health CENTERS FOR MEDICARE... LABORATORY REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing Moderate Complexity Testing § 493.1421 Condition: Laboratories performing moderate complexity testing; testing personnel....

  7. 42 CFR 493.1421 - Condition: Laboratories performing moderate complexity testing; testing personnel.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... complexity testing; testing personnel. 493.1421 Section 493.1421 Public Health CENTERS FOR MEDICARE... LABORATORY REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing Moderate Complexity Testing § 493.1421 Condition: Laboratories performing moderate complexity testing; testing personnel....

  8. Pilot scale cooling tower fouled fill treatment: AFCATT (Anti-Fouling Chemical Additive Test Tower)

    SciTech Connect

    Newton, M.T.; Noble, R.T.; Philpot, E.F.; Eastis, J.H.

    1995-02-01

    Polyvinylchloride (PVC) film-type cellular fill is the fill of choice in replacing cement asbestor board fill in existing cooling towers and in new cooling towers because of its high thermal performance, ease of installation, and low initial cost. However, PVC fill has been found to foul quickly with biological and sediment material, significant reducing tower performance and the fill`s useful life. The Anti-Fouling Chemical Additives Test Tower (AFCATT) has been built to study accumulation rates of fouling deposits in corrugated PVC film fill and to study methods of cleaning and preventing the fouling deposits. This small mechanical draft cooling tower is located next to the Unit 4 natural draft cooling tower at Georgia Power Company`s Plant Bowen. The once-through mechanical draft tower receives hot water from the condenser and returns the cold water to the basin of the host tower. The pilot tower is divided into four chambers allowing for three different treatment programs and one control to be run simultaneously. PVC fill packs are suspended from load cells to allow the weight of the fill packs to be measured continuously. Six vendors participated in the summer 1993 test program. Each proposed different methods of cleaning the fouled fill and were given the opportunity to try their proposed method of fill cleaning. The success of each treatment program was determined by its ability to reduce fill pack weight (i.e., reduce fouling).

  9. Performance improvement of CGHs for optical testing

    NASA Astrophysics Data System (ADS)

    Pruss, Christof; Reichelt, Stephan; Korolkov, Victor P.; Osten, Wolfgang; Tiziani, Hans J.

    2003-05-01

    The expansion of the field of diffractive optics applications is accompanied by toughening performance requirements for CGHs. Optical testing sets especially high requirements, concerning wavefront accuracy and diffraction efficiency. The key point in fabrication technology is the writing system creating the photomask or the profiled pattern. The diffractive optics fabrication facility at ITO (University of Stuttgart) is based on the circular laser writing system CLWS-300. This flexible and high-accurate tool was originally designed for binary diffractive optics fabrication. This paper presents novel enhancements of this system allowing direct laser writing of a wide range of binary and continuous-relief CGHs on photoresist layers, chromium films and LDW-glass. Main topics of the enhancements were the scanning accuracy and exposure control. Many types of CGHs (binary precision holograms for optical testing, Shack-Hartmann arrays, microlens discs for confocal microscopy, diffractive interferometer objectives, doughnut generators etc.) have been manufactured using the developed algorithms and hardware.

  10. Big area additive manufacturing of high performance bonded NdFeB magnets

    SciTech Connect

    Li, Ling; Tirado, Angelica; Nlebedim, I. C.; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R. R.; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A.; Paranthaman, M. Parans

    2016-10-31

    Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm3, and the room temperature magnetic properties are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. As a result, the present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.

  11. Big area additive manufacturing of high performance bonded NdFeB magnets

    DOE PAGES

    Li, Ling; Tirado, Angelica; Nlebedim, I. C.; ...

    2016-10-31

    Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm3, and the room temperature magnetic propertiesmore » are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. As a result, the present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.« less

  12. Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets

    PubMed Central

    Li, Ling; Tirado, Angelica; Nlebedim, I. C.; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R. R.; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A.; Paranthaman, M. Parans

    2016-01-01

    Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm3, and the room temperature magnetic properties are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. The present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials. PMID:27796339

  13. Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets.

    PubMed

    Li, Ling; Tirado, Angelica; Nlebedim, I C; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R R; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A; Paranthaman, M Parans

    2016-10-31

    Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm(3), and the room temperature magnetic properties are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m(3) (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. The present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.

  14. Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets

    NASA Astrophysics Data System (ADS)

    Li, Ling; Tirado, Angelica; Nlebedim, I. C.; Rios, Orlando; Post, Brian; Kunc, Vlastimil; Lowden, R. R.; Lara-Curzio, Edgar; Fredette, Robert; Ormerod, John; Lograsso, Thomas A.; Paranthaman, M. Parans

    2016-10-01

    Additive manufacturing allows for the production of complex parts with minimum material waste, offering an effective technique for fabricating permanent magnets which frequently involve critical rare earth elements. In this report, we demonstrate a novel method - Big Area Additive Manufacturing (BAAM) - to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm3, and the room temperature magnetic properties are: intrinsic coercivity Hci = 688.4 kA/m, remanence Br = 0.51 T, and energy product (BH)max = 43.49 kJ/m3 (5.47 MGOe). In addition, tensile tests performed on four dog-bone shaped specimens yielded an average ultimate tensile strength of 6.60 MPa and an average failure strain of 4.18%. Scanning electron microscopy images of the fracture surfaces indicate that the failure is primarily related to the debonding of the magnetic particles from the polymer binder. The present method significantly simplifies manufacturing of near-net-shape bonded magnets, enables efficient use of rare earth elements thus contributing towards enriching the supply of critical materials.

  15. 20 CFR 666.110 - May a Governor require additional indicators of performance?

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 4 2014-04-01 2014-04-01 false May a Governor require additional indicators of performance? 666.110 Section 666.110 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION..., Governors may develop additional indicators of performance for adults, youth and dislocated...

  16. Testing Game-Based Performance in Team-Handball.

    PubMed

    Wagner, Herbert; Orwat, Matthias; Hinz, Matthias; Pfusterschmied, Jürgen; Bacharach, David W; von Duvillard, Serge P; Müller, Erich

    2016-10-01

    Wagner, H, Orwat, M, Hinz, M, Pfusterschmied, J, Bacharach, DW, von Duvillard, SP, and Müller, E. Testing game-based performance in team-handball. J Strength Cond Res 30(10): 2794-2801, 2016-Team-handball is a fast paced game of defensive and offensive action that includes specific movements of jumping, passing, throwing, checking, and screening. To date and to the best of our knowledge, a game-based performance test (GBPT) for team-handball does not exist. Therefore, the aim of this study was to develop and validate such a test. Seventeen experienced team-handball players performed 2 GBPTs separated by 7 days between each test, an incremental treadmill running test, and a team-handball test game (TG) (2 × 20 minutes). Peak oxygen uptake (V[Combining Dot Above]O2peak), blood lactate concentration (BLC), heart rate (HR), sprinting time, time of offensive and defensive actions as well as running intensities, ball velocity, and jump height were measured in the game-based test. Reliability of the tests was calculated using an intraclass correlation coefficient (ICC). Additionally, we measured V[Combining Dot Above]O2peak in the incremental treadmill running test and BLC, HR, and running intensities in the team-handball TG to determine the validity of the GBPT. For the test-retest reliability, we found an ICC >0.70 for the peak BLC and HR, mean offense and defense time, as well as ball velocity that yielded an ICC >0.90 for the V[Combining Dot Above]O2peak in the GBPT. Percent walking and standing constituted 73% of total time. Moderate (18%) and high (9%) intensity running in the GBPT was similar to the team-handball TG. Our results indicated that the GBPT is a valid and reliable test to analyze team-handball performance (physiological and biomechanical variables) under conditions similar to competition.

  17. 40 CFR 60.104a - Performance tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Performance tests. 60.104a Section 60... tests. (a) The owner or operator shall conduct a performance test for each FCCU, FCU, sulfur recovery....8(d) apply to the initial performance test and to subsequent performance tests required by...

  18. Evaluation of the performance of smoothing functions in generalized additive models for spatial variation in disease.

    PubMed

    Siangphoe, Umaporn; Wheeler, David C

    2015-01-01

    Generalized additive models (GAMs) with bivariate smoothing functions have been applied to estimate spatial variation in risk for many types of cancers. Only a handful of studies have evaluated the performance of smoothing functions applied in GAMs with regard to different geographical areas of elevated risk and different risk levels. This study evaluates the ability of different smoothing functions to detect overall spatial variation of risk and elevated risk in diverse geographical areas at various risk levels using a simulation study. We created five scenarios with different true risk area shapes (circle, triangle, linear) in a square study region. We applied four different smoothing functions in the GAMs, including two types of thin plate regression splines (TPRS) and two versions of locally weighted scatterplot smoothing (loess). We tested the null hypothesis of constant risk and detected areas of elevated risk using analysis of deviance with permutation methods and assessed the performance of the smoothing methods based on the spatial detection rate, sensitivity, accuracy, precision, power, and false-positive rate. The results showed that all methods had a higher sensitivity and a consistently moderate-to-high accuracy rate when the true disease risk was higher. The models generally performed better in detecting elevated risk areas than detecting overall spatial variation. One of the loess methods had the highest precision in detecting overall spatial variation across scenarios and outperformed the other methods in detecting a linear elevated risk area. The TPRS methods outperformed loess in detecting elevated risk in two circular areas.

  19. Evaluation of the Performance of Smoothing Functions in Generalized Additive Models for Spatial Variation in Disease

    PubMed Central

    Siangphoe, Umaporn; Wheeler, David C.

    2015-01-01

    Generalized additive models (GAMs) with bivariate smoothing functions have been applied to estimate spatial variation in risk for many types of cancers. Only a handful of studies have evaluated the performance of smoothing functions applied in GAMs with regard to different geographical areas of elevated risk and different risk levels. This study evaluates the ability of different smoothing functions to detect overall spatial variation of risk and elevated risk in diverse geographical areas at various risk levels using a simulation study. We created five scenarios with different true risk area shapes (circle, triangle, linear) in a square study region. We applied four different smoothing functions in the GAMs, including two types of thin plate regression splines (TPRS) and two versions of locally weighted scatterplot smoothing (loess). We tested the null hypothesis of constant risk and detected areas of elevated risk using analysis of deviance with permutation methods and assessed the performance of the smoothing methods based on the spatial detection rate, sensitivity, accuracy, precision, power, and false-positive rate. The results showed that all methods had a higher sensitivity and a consistently moderate-to-high accuracy rate when the true disease risk was higher. The models generally performed better in detecting elevated risk areas than detecting overall spatial variation. One of the loess methods had the highest precision in detecting overall spatial variation across scenarios and outperformed the other methods in detecting a linear elevated risk area. The TPRS methods outperformed loess in detecting elevated risk in two circular areas. PMID:25983545

  20. 49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... or double-lane change test performed at the test track. Bus speed should be held constant throughout... left- and right-hand lane changes should be tested. 4. Performance The performance test should...

  1. 49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... or double-lane change test performed at the test track. Bus speed should be held constant throughout... left- and right-hand lane changes should be tested. 4. Performance The performance test should...

  2. 49 CFR Appendix A to Part 665 - Tests To Be Performed at the Bus Testing Facility

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... or double-lane change test performed at the test track. Bus speed should be held constant throughout... left- and right-hand lane changes should be tested. 4. Performance The performance test should...

  3. History of personal dosimetry performance testing in the United States.

    PubMed

    Soares, C G

    2007-01-01

    The basis for personal dosimetry performance testing in the United States is ANSI/HPS N13.11 (2001). Now in its third edition, this standard has been in place since 1983. Testing under this standard is administered by the National Voluntary Accreditation Program (NVLAP), and accreditation of dosimetry processors under this program is required by US Nuclear Regulatory Commission (NRC) regulations. The US Department of Energy (DOE) also maintains a testing program for its laboratories and contractors, administered by the Department of Energy Laboratory Accreditation Program (DOELAP). A focus in recent years has been the modification of ANSI/HPS N13.11 to allow acceptance by both testing programs in order to bring harmonisation to US personal dosemeter processing testing. Since there is no type testing program in the US for personal dosemeters, the testing philosophy of ANSI N13.11 has always combined elements of type testing and routine performance testing. This philosophy is explored in detail in this presentation, along with trends in the development of the document to its present state. In addition, a look will be taken at what the future holds for the next revision of the document, scheduled to begin in 2005.

  4. Effort, symptom validity testing, performance validity testing and traumatic brain injury

    PubMed Central

    Bigler, Erin D.

    2014-01-01

    Abstract Background: To understand the neurocognitive effects of brain injury, valid neuropsychological test findings are paramount. Review: This review examines the research on what has been referred to a symptom validity testing (SVT). Above a designated cut-score signifies a ‘passing’ SVT performance which is likely the best indicator of valid neuropsychological test findings. Likewise, substantially below cut-point performance that nears chance or is at chance signifies invalid test performance. Significantly below chance is the sine qua non neuropsychological indicator for malingering. However, the interpretative problems with SVT performance below the cut-point yet far above chance are substantial, as pointed out in this review. This intermediate, border-zone performance on SVT measures is where substantial interpretative challenges exist. Case studies are used to highlight the many areas where additional research is needed. Historical perspectives are reviewed along with the neurobiology of effort. Reasons why performance validity testing (PVT) may be better than the SVT term are reviewed. Conclusions: Advances in neuroimaging techniques may be key in better understanding the meaning of border zone SVT failure. The review demonstrates the problems with rigidity in interpretation with established cut-scores. A better understanding of how certain types of neurological, neuropsychiatric and/or even test conditions may affect SVT performance is needed. PMID:25215453

  5. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the additives in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power has provided the Texas lignite/PRB co-fired test site for pilot FGD tests and cost sharing. Southern Company has provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation is providing the TMT-15 additive, and the Nalco Company is providing the Nalco 8034 additive. Both companies are also supplying technical support to the test program as in-kind cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management

  6. Field Testing of a Wet FGD Additive for Enhanced Mercury Control

    SciTech Connect

    Gary Blythe; MariJon Owens

    2007-12-31

    This document is the final report for DOE-NETL Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project has been to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project was intended to demonstrate whether such additives can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project involved pilot- and full-scale tests of the additives in wet FGD absorbers. The tests were intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power provided the Texas lignite/PRB co-fired test site for pilot FGD tests and project cost sharing. Southern Company provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested, and project cost sharing. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation provided the TMT-15 additive, and the Nalco Company provided the Nalco 8034 additive. Both companies also supplied technical support to the test program as in-kind cost sharing. The project was conducted in six tasks. Of the six tasks, Task 1 involved project planning and Task 6 involved

  7. Evaluation of potential performance additives for the advanced lithium bromide chiller

    SciTech Connect

    Reiner, R.H.; Del Cul, W.; Perez-Blanco, H.; Ally, M.R.; Zaltash, A.

    1991-04-01

    The effectiveness and stability of potential heat-and-mass transfer (performance) additives for an advanced lithium bromide (LiBr) chiller were evaluated in a series of experimental studies. These studies of additive effectiveness and stability were necessary because many currently used performance additives decompose at the high generator temperatures (220{degrees}C to 260{degrees}C) desired for this particular advanced LiBr chiller. For example, one common performance additive, 2-ethyl-l-hexanol (2EH), reacts with the corrosion inhibitor, lithium chromate (Li{sub 2}CrO{sub 4}), even at moderate generator temperatures ({ge}180{degrees}C). These stability problems can be mitigated by using less reactive corrosion inhibitors such as lithium molybdate (Li{sub 2}MoO{sub 4}) and by using more stable performance additives such as 1-heptanol (HEP) or 1H,1H,7H-dodecafluoro-1-heptanol (DFH). There seems to be a trade-off between additive stability and effectiveness: the most effective performance additives are not the most stable additives. These studies indicate that HEP or DFH may be effective additives in the advanced LiBr chiller if Li{sub 2}MoO{sub 4} is used as a corrosion inhibitor.

  8. Functional Performance Testing for Power and Return to Sports

    PubMed Central

    Manske, Robert; Reiman, Michael

    2013-01-01

    Context: Functional performance testing of athletes can determine physical limitations that may affect sporting activities. Optimal functional performance testing simulates the athlete’s activity. Evidence Acquisition: A Medline search from 1960 to 2012 was implemented with the keywords functional testing, functional impairment testing, and functional performance testing in the English language. Each author also undertook independent searches of article references. Conclusion: Functional performance tests can bridge the gap between general physical tests and full, unrestricted athletic activity. PMID:24427396

  9. Power Performance Test Report for the Southwest Windpower AIR-X Wind Turbine

    SciTech Connect

    van Dam, J.; Meadors, M.; Link, H.; Migliore, P.

    2003-09-01

    In the period from 14 October 2002 to 16 January 2003, an early production version of Southwest Windpower's AIR-X turbine was installed at the NWTC test site for acoustic noise testing. In addition to the signals required for the noise testing, additional instrumentation that allowed power performance testing in accordance with IEC 61400-12[1] was added. The results of that test are described in this report. Please note that this test and the test report are not an accredited power performance test/test report because parts of the NWTC quality assurance system were not followed.

  10. A test strategy for the assessment of additive attributed toxicity of tobacco products.

    PubMed

    Kienhuis, Anne S; Staal, Yvonne C M; Soeteman-Hernández, Lya G; van de Nobelen, Suzanne; Talhout, Reinskje

    2016-08-01

    The new EU Tobacco Product Directive (TPD) prohibits tobacco products containing additives that are toxic in unburnt form or that increase overall toxicity of the product. This paper proposes a strategy to assess additive attributed toxicity in the context of the TPD. Literature was searched on toxicity testing strategies for regulatory purposes from tobacco industry and governmental institutes. Although mainly traditional in vivo testing strategies have been applied to assess toxicity of unburnt additives and increases in overall toxicity of tobacco products due to additives, in vitro tests combined with toxicogenomics and validated using biomarkers of exposure and disease are most promising in this respect. As such, tests are needed that are sensitive enough to assess additive attributed toxicity above the overall toxicity of tobacco products, which can associate assay outcomes to human risk and exposure. In conclusion, new, sensitive in vitro assays are needed to conclude whether comparable testing allows for assessment of small changes in overall toxicity attributed to additives. A more pragmatic approach for implementation on a short-term is mandated lowering of toxic emission components. Combined with risk assessment, this approach allows assessment of effectiveness of harm reduction strategies, including banning or reducing of additives.

  11. Singlepath Salmonella. Performance Tested Method 060401.

    PubMed

    Lindhardt, Charlotte; Schönenbrücher, Holger; Slaghuis, Jörg; Bubert, Andreas; Ossmer, Rolf

    2009-01-01

    Singlepath Salmonella is an immunochromatographic (lateral flow) assay for the presumptive qualitative detection of Salmonella spp. in food. A previous AOAC Performance Tested Method study evaluated Singlepath Salmonella as an effective method for the detection of Salmonella spp. in the following selected foods: dried skimmed milk, black pepper, dried pet food, desiccated coconut, cooked peeled frozen prawns, raw ground beef, and raw ground turkey. In this Emergency Response Validation extension, creamy peanut butter was inoculated with S. enterica. ser. Typhimurium. For low contamination level (1.08 CFU/25 g), a Chi-square value of 0.5 indicated that there was no significant difference between Singlepath Salmonella and the U.S. Food and Drug Administration's Bacteriological Analytical Manual (FDA-BAM) reference method. For high-level and uninoculated control there was 100% agreement between the methods.

  12. RHIC Sextant Test --- Physics and Performance

    NASA Astrophysics Data System (ADS)

    Wei, J.; Fischer, W.; Ahrens, L.; Brennan, J. M.; Brown, K.; Connolly, R.; dell, G. F.; Harrison, M.; Kewisch, J.; Mackay, W. W.; Mane, V.; Peggs, S.; Pilat, F.; Satogata, T.; Tepikian, S.; Thompson, P.; Trahern, C. G.; Trbojevic, D.; Tsoupas, N.

    1997-05-01

    This paper presents beam physics and machine performance results of the Relativistic Heavy Ion Collider (RHIC) Sextant and AGS-to-RHIC (ATR) transfer line during the Sextant test in early 1997. Techniques used to measure both machine properties (difference orbits, dispersion, and beamline optics) and beam parameters (energy, intensity, transverse and longitudinal emittances) are described. The flexibility of the ATR and RHIC Sextant lattices is demonstrated by a widely tunable range of phase advance per cell. Longitudinal tomography is employed to reconstruct beam motion in phase space. Digitized two-dimensional video profile monitors are used to measure transverse beam emittances and beamline optics. The gold ion beam parameters are shown to be comparable to the RHIC design requirements.

  13. Rates of False-Positive Classification Resulting From the Analysis of Additional Embedded Performance Validity Measures.

    PubMed

    Silk-Eglit, Graham M; Stenclik, Jessica H; Miele, Andrea S; Lynch, Julie K; McCaffrey, Robert J

    2015-01-01

    Several studies have documented improvements in the classification accuracy of performance validity tests (PVTs) when they are combined to form aggregated models. Fewer studies have evaluated the impact of aggregating additional PVTs and changing the classification threshold within these models. A recent Monte Carlo simulation demonstrated that to maintain a false-positive rate (FPR) of ≤.10, only 1, 4, 8, 10, and 15 PVTs should be analyzed at classification thresholds of failing at least 1, at least 2, at least 3, at least 4, and at least 5 PVTs, respectively. The current study sought to evaluate these findings with embedded PVTs in a sample of real-life litigants and to highlight a potential danger in analytic flexibility with embedded PVTs. Results demonstrated that to maintain an FPR of ≤.10, only 3, 7, 10, 14, and 15 PVTs should be analyzed at classification thresholds of failing at least 1, at least 2, at least 3, at least 4, and at least 5 PVTs, respectively. Analyzing more than these numbers of PVTs resulted in a dramatic increase in the FPR. In addition, in the most extreme case, flexibility in analyzing and reporting embedded PVTs increased the FPR by 67%. Given these findings, a more objective approach to analyzing and reporting embedded PVTs should be introduced.

  14. On-line tests of organic additives for the inhibition of the precipitation of silica from hypersaline geothermal brine IV. Final tests of candidate additives

    SciTech Connect

    Harrar, J.E.; Locke, F.E.; Otto, C.H. Jr.; Lorensen, L.E.; Frey, W.P.; Snell, E.O.

    1980-02-01

    The Lawrence Livermore Laboratory Brine Treatment Test System at Niland, Imperial Valley, California, has been used to evaluate a number of cationic polymers and surfactants as scale control agents. An initial group of compounds was narrowed to four on the basis of their activity as silica precipitation inhibitors. Three of these and certain combinations of compounds were then given a 40-h test to determine their effectiveness in retarding scales formed at 220, 125, and 90/sup 0/C. The best single compound was Corcat P-18 (Cordova Chemical Co. polyethylene imine, M.W. approx. = 1800). It had no effect on the scale at 220/sup 0/C, but it reduced the scales at 125 and 90/sup 0/C by factors of 4 and 18, respectively, and it also has activity as a corrosion inhibitor. Other promising compounds are PAE HCl (Dynapol poly(aminoethylene, HCl salt)), which also somewhat reduces the 220/sup 0/C scale; Ethoquad 18/25 (Armak methyl polyoxyethylene(15) octadecylammonium chloride); and Mirapol A-15 (a Miranol Chemical polydiquaternary compound). The best additive formulation for the brines of the Salton Sea Geothermal Field appears to be a mixture of one of these silica precipitation inhibitors with a small amount of hydrochloric acid and a phosphonate crystalline deposit inhibitor. Speculations are presented as to the mechanism of inhibition of silica precipitation and recommendations for further testing of these additives.

  15. Indicators of Ceriodaphnia dubia chronic toxicity test performance and sensitivity

    SciTech Connect

    Rosebrock, M.M.; Bedwell, N.J.; Ausley, L.W.

    1994-12-31

    The North Carolina Division of Environmental Management has begun evaluation of the sensitivity of test results used for measuring chronic whole effluent toxicity in North Carolina wastewater discharges. Approximately 67% of 565 facilities required to monitor toxicity by an NPDES permit perform a Ceriodaphnia dubia chronic, single effluent concentration (pass/fail) analysis. Data from valid Ceriodaphnia dubia chronic pass/fail tests performed by approximately 20 certified biological laboratories and submitted by North Carolina NPDES permittees were recorded beginning January 1992. Control and treatment reproduction data from over 2,500 tests submitted since 1992 were analyzed to determine the minimum significant difference (MSD) at a 99% confidence level for each test and the percent reduction from the control mean that the MSD represents (%MSD) for each certified laboratory. Initial results for the 20 laboratories indicate that the average intralaboratory percent MSD ranges 12.72% (n = 367) to 34.91% (n = 7) with an average of 23.08%. Additionally, over 3,800 tests were analyzed to determine the coefficient of variation (CV) for control reproduction for each test and the average for each certified biological laboratory. Preliminary review indicates that average interlaboratory control reproduction CV values range from 10.59% (n = 367) to 31.08% (n = 572) with a mean of 20.35%. The statistics investigated are indicators of intra/interlaboratory performance and sensitivity of Ceriodaphnia chronic toxicity analyses.

  16. Fracture testing and performance of beryllium copper alloy C17510

    SciTech Connect

    Murray, H.A.; Zatz, I.J.

    1994-05-01

    When a literature search and discussion with manufacturers revealed that there was virtually no existing data related to the fracture properties and behavior of copper beryllium alloy C17510, a series of test programs was undertaken to ascertain this information for several variations in material processing and chemistry. These variations in C17510 were primarily optimized for combinations of strength and conductivity. While originally intended for use as cyclically loaded high-field, high-strength conductors in fusion energy research, material testing of C17510 has indicated that it is an attractive and economical alternative for a host of other structural, mechanical and electrical applications. ASTM tests performed on three variations of C17510 alloys included both J-integral and plane strain fracture toughness testing and fatigue crack growth rate tests, as well as verifying tensile, hardness, Charpy, and other well defined mechanical properties. Fracture testing was performed at both room and liquid nitrogen temperatures, which bound the thermal environment anticipated for the fusion components being designed. Fatigue crack propagation stress ratios ranged from nominal zero to minus one at each temperature. In order to confirm the test results, duplicate and independent test programs were awarded to separate facilities with appropriate test experience, whenever possible. The primary goal of the test program, to determine and bound the fracture toughness and Paris constants for C17510,was accomplished. In addition, a wealth of information was accumulated pertaining to crack growth characteristics, effects of directionality and potential testing pitfalls. The paper discusses the test program and its findings in detail.

  17. 40 CFR 63.1656 - Performance testing, test methods, and compliance demonstrations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Performance testing, test methods, and...: Ferromanganese and Silicomanganese § 63.1656 Performance testing, test methods, and compliance demonstrations. (a) Performance testing. (1) All performance tests must be conducted according to the requirements in § 63.7...

  18. 40 CFR 63.1656 - Performance testing, test methods, and compliance demonstrations.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Performance testing, test methods, and...: Ferromanganese and Silicomanganese § 63.1656 Performance testing, test methods, and compliance demonstrations. (a) Performance testing. (1) All performance tests must be conducted according to the requirements in § 63.7...

  19. 40 CFR 63.1656 - Performance testing, test methods, and compliance demonstrations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Performance testing, test methods, and...: Ferromanganese and Silicomanganese § 63.1656 Performance testing, test methods, and compliance demonstrations. (a) Performance testing. (1) All performance tests must be conducted according to the requirements in § 63.7...

  20. 40 CFR 63.7 - Performance testing requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... the results of the compliance test. Acceptance of the test results shall constitute a waiver of the... Performance testing requirements. (a) Applicability and performance test dates. (1) The applicability of this... or operator of the affected source must perform such tests within 180 days of the compliance date...

  1. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  2. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  3. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Blowout Preventer (bop) System Requirements § 250.449 What additional BOP... water to conduct this test. You may use drilling fluids to conduct subsequent tests of a subsea...

  4. 76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-21

    ... AGENCY 40 CFR Part 80 RIN 2060-AP17 Regulation of Fuel and Fuel Additives: Alternative Test Method for... alternative test method for olefin content in gasoline. This final rule will provide flexibility to the... environmental benefits achieved from our fuels programs. ] DATES: This rule is effective November 21,...

  5. Polysulfide and bio-based EP additive performance in vegetable vs. paraffinic base oils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Twist compression test (TCT) and 4-ball extreme pressure (EP) methods were used to investigate commercial polysulfide (PS) and bio-based polyester (PE) EP additives in paraffinic (150N) and refined soybean (SOY) base oils of similar viscosity. Binary blends of EP additive and base oil were investiga...

  6. Improvements and Performance of the Fermilab Solenoid Test Facility

    DOE PAGES

    Orris, Darryl; Arnold, Don; Brandt, Jeffrey; ...

    2017-06-01

    Here, the Solenoid Test Facility at Fermilab was built using a large vacuum vessel for testing of conduction-cooled superconducting solenoid magnets, and was first used to determine the performance of the MICE Coupling Coil. The facility was modified recently to enable testing of solenoid magnets for the Mu2e experiment, which operate at much higher current than the Coupling Coil. One pair of low current conduction-cooled copper and NbTi leads was replaced with two pairs of 10 kA HTS leads cooled by heat exchange with liquid nitrogen and liquid helium. The new design, with additional control and monitoring capability, also providesmore » helium cooling of the superconducting magnet leads by conduction. A high current power supply with energy extraction was added, and several improvements to the quench protection and characterization system were made. Here we present details of these changes and report on performance results from a test of the Mu2e prototype Transport Solenoid (TS) module. Progress on additional improvements in preparation for production TS module testing will be presented.« less

  7. Improvements and performance of the Fermilab solenoid test facility

    SciTech Connect

    Orris, Darryl; Arnold, Don; Brandt, Jeffrey; Cheban, Sergey; Evbota, Daniel; Feher, Sandor; Galt, Artur; Hays, Steven; Hemmati, Ali; Hess, Charles; Hocker, James A.; Kim, Min Jeong; Kokoska, Lidija; Koshelev, Sergey; Kotelnikov, Sergey; Lamm, Michael; Lopes, Mauricio L.; Nogiec, Jerzy; Page, Thomas M.; Pilipenko, Roman; Rabehl, Roger; Sylvester, Cosmore; Tartaglia, Michael; Vouris, Antonios

    2016-12-15

    Here, the Solenoid Test Facility at Fermilab was built using a large vacuum vessel for testing of conduction-cooled superconducting solenoid magnets, and was first used to determine the performance of the MICE Coupling Coil. The facility was modified recently to enable testing of solenoid magnets for the Mu2e experiment, which operate at much higher current than the Coupling Coil. One pair of low current conduction-cooled copper and NbTi leads was replaced with two pairs of 10 kA HTS leads cooled by heat exchange with liquid nitrogen and liquid helium. The new design, with additional control and monitoring capability, also provides helium cooling of the superconducting magnet leads by conduction. A high current power supply with energy extraction was added, and several improvements to the quench protection and characterization system were made. Here we present details of these changes and report on performance results from a test of the Mu2e prototype Transport Solenoid (TS) module. Progress on additional improvements in preparation for production TS module testing will be presented.

  8. High Energy Density Additives for Hybrid Fuel Rockets to Improve Performance and Enhance Safety

    NASA Technical Reports Server (NTRS)

    Jaffe, Richard L.

    2014-01-01

    We propose a conceptual study of prototype strained hydrocarbon molecules as high energy density additives for hybrid rocket fuels to boost the performance of these rockets without compromising safety and reliability. Use of these additives could extend the range of applications for which hybrid rockets become an attractive alternative to conventional solid or liquid fuel rockets. The objectives of the study were to confirm and quantify the high enthalpy of these strained molecules and to assess improvement in rocket performance that would be expected if these additives were blended with conventional fuels. We confirmed the chemical properties (including enthalpy) of these additives. However, the predicted improvement in rocket performance was too small to make this a useful strategy for boosting hybrid rocket performance.

  9. Additive effects of beta-alanine and sodium bicarbonate on upper-body intermittent performance.

    PubMed

    Tobias, Gabriel; Benatti, Fabiana Braga; de Salles Painelli, Vitor; Roschel, Hamilton; Gualano, Bruno; Sale, Craig; Harris, Roger C; Lancha, Antonio Herbert; Artioli, Guilherme Gianinni

    2013-08-01

    We examined the isolated and combined effects of beta-alanine (BA) and sodium bicarbonate (SB) on high-intensity intermittent upper-body performance in judo and jiu-jitsu competitors. 37 athletes were assigned to one of four groups: (1) placebo (PL)+PL; (2) BA+PL; (3) PL+SB or (4) BA+SB. BA or dextrose (placebo) (6.4 g day⁻¹) was ingested for 4 weeks and 500 mg kg⁻¹ BM of SB or calcium carbonate (placebo) was ingested for 7 days during the 4th week. Before and after 4 weeks of supplementation, the athletes completed four 30-s upper-body Wingate tests, separated by 3 min. Blood lactate was determined at rest, immediately after and 5 min after the 4th exercise bout, with perceived exertion reported immediately after the 4th bout. BA and SB alone increased the total work done in +7 and 8 %, respectively. The co-ingestion resulted in an additive effect (+14 %, p < 0.05 vs. BA and SB alone). BA alone significantly improved mean power in the 2nd and 3rd bouts and tended to improve the 4th bout. SB alone significantly improved mean power in the 4th bout and tended to improve in the 2nd and 3rd bouts. BA+SB enhanced mean power in all four bouts. PL+PL did not elicit any alteration on mean and peak power. Post-exercise blood lactate increased with all treatments except with PL+PL. Only BA+SB resulted in lower ratings of perceived exertion (p = 0.05). Chronic BA and SB supplementation alone equally enhanced high-intensity intermittent upper-body performance in well-trained athletes. Combined BA and SB promoted a clear additive ergogenic effect.

  10. Effects of Total SAT® Test Time on Performance and Fatigue. Research Notes. RN-37

    ERIC Educational Resources Information Center

    Ackerman, Phillip L.; Kanfer, Ruth; Wolman, Stacey D.

    2005-01-01

    The current study was designed to examine performance effects and fatigue effects associated with different total SAT testing times. In addition, the researchers examined personality, motivation, and other determinants of individual differences in examinee fatigue before, during, and after testing.

  11. Hybrid Residual Flexibility/Mass-Additive Method for Structural Dynamic Testing

    NASA Technical Reports Server (NTRS)

    Tinker, M. L.

    2003-01-01

    A large fixture was designed and constructed for modal vibration testing of International Space Station elements. This fixed-base test fixture, which weighs thousands of pounds and is anchored to a massive concrete floor, initially utilized spherical bearings and pendulum mechanisms to simulate Shuttle orbiter boundary constraints for launch of the hardware. Many difficulties were encountered during a checkout test of the common module prototype structure, mainly due to undesirable friction and excessive clearances in the test-article-to-fixture interface bearings. Measured mode shapes and frequencies were not representative of orbiter-constrained modes due to the friction and clearance effects in the bearings. As a result, a major redesign effort for the interface mechanisms was undertaken. The total cost of the fixture design, construction and checkout, and redesign was over $2 million. Because of the problems experienced with fixed-base testing, alternative free-suspension methods were studied, including the residual flexibility and mass-additive approaches. Free-suspension structural dynamics test methods utilize soft elastic bungee cords and overhead frame suspension systems that are less complex and much less expensive than fixed-base systems. The cost of free-suspension fixturing is on the order of tens of thousands of dollars as opposed to millions, for large fixed-base fixturing. In addition, free-suspension test configurations are portable, allowing modal tests to be done at sites without modal test facilities. For example, a mass-additive modal test of the ASTRO-1 Shuttle payload was done at the Kennedy Space Center launch site. In this Technical Memorandum, the mass-additive and residual flexibility test methods are described in detail. A discussion of a hybrid approach that combines the best characteristics of each method follows and is the focus of the study.

  12. Role of inorganic additives on the ballistic performance of gun propellant formulations.

    PubMed

    Damse, R S; Sikder, A K

    2008-06-15

    This paper explores the possibility of increasing the ballistic performance of gun propellant with the addition of inorganic additives viz. aluminium and ammonium perchlorate. Compositions based on propellant NQ containing additional aluminium and ammonium perchlorate in different parts were studied theoretically and experimentally. Performance in respect of ballistic parameters, sensitivity, thermal characteristics, thermal stability and mechanical properties are evaluated and compared with that of the conventional triple base propellant NQ. Experimental data on comparative study indicate that the compositions containing aluminium and ammonium perchlorate are superior to propellant NQ in respect of energy.

  13. 49 CFR 572.78 - Performance test conditions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 7 2012-10-01 2012-10-01 false Performance test conditions. 572.78 Section 572.78... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) ANTHROPOMORPHIC TEST DEVICES 6-Year-Old Child § 572.78 Performance test conditions. (a) Conduct performance tests at any temperature from 66 °F to 78 °F, and at...

  14. Evaluation of laser ultrasonic testing for inspection of metal additive manufacturing

    NASA Astrophysics Data System (ADS)

    Everton, Sarah; Dickens, Phill; Tuck, Chris; Dutton, Ben

    2015-03-01

    Additive Manufacturing (AM) offers a number of benefits over conventional processes. However, in order for these benefits to be realised, further development and integration of suitable monitoring and closed loop control systems are needed. Laser Ultrasonic Testing (LUT) is an inspection technology which shows potential for in-situ monitoring of metallic AM processes. Non-contact measurements can be performed on curved surfaces and in difficult to reach areas, even at elevated temperatures. Interrogation of each build layer generates defect information which can be used to highlight processing errors and allow for real-time modification of processing parameters, enabling improved component quality and yield. This study evaluates the use of laser-generated surface waves to detect artificially generated defects in titanium alloy (Ti- 6Al-4V) samples produced by laser-based Powder Bed Fusion. The trials undertaken utilise the latest LUT equipment, recently installed at Manufacturing Technology Centre which is capable of being controlled remotely. This will allow the system to optimise or adapt "on-the-fly", simplifying the eventual integration of the system within an AM machine.

  15. AULA virtual reality test as an attention measure: convergent validity with Conners' Continuous Performance Test.

    PubMed

    Díaz-Orueta, Unai; Garcia-López, Cristina; Crespo-Eguílaz, Nerea; Sánchez-Carpintero, Rocío; Climent, Gema; Narbona, Juan

    2014-01-01

    The majority of neuropsychological tests used to evaluate attention processes in children lack ecological validity. The AULA Nesplora (AULA) is a continuous performance test, developed in a virtual setting, very similar to a school classroom. The aim of the present study is to analyze the convergent validity between the AULA and the Continuous Performance Test (CPT) of Conners. The AULA and CPT were administered correlatively to 57 children, aged 6-16 years (26.3% female) with average cognitive ability (IQ mean = 100.56, SD = 10.38) who had a diagnosis of attention deficit/hyperactivity disorder (ADHD) according to DSM-IV-TR criteria. Spearman correlations analyses were conducted among the different variables. Significant correlations were observed between both tests in all the analyzed variables (omissions, commissions, reaction time, and variability of reaction time), including for those measures of the AULA based on different sensorial modalities, presentation of distractors, and task paradigms. Hence, convergent validity between both tests was confirmed. Moreover, the AULA showed differences by gender and correlation to Perceptual Reasoning and Working Memory indexes of the WISC-IV, supporting the relevance of IQ measures in the understanding of cognitive performance in ADHD. In addition, the AULA (but not Conners' CPT) was able to differentiate between ADHD children with and without pharmacological treatment for a wide range of measures related to inattention, impulsivity, processing speed, motor activity, and quality of attention focus. Additional measures and advantages of the AULA versus Conners' CPT are discussed.

  16. The XRS Low Temperature Cryogenic System: Ground Performance Test Results

    NASA Technical Reports Server (NTRS)

    Breon, Susan; Sirron, Peter; Boyle, Robert; Canavan, Ed; DiPirro, Michael; Serlemitsos, Aristides; Tuttle, James; Whitehouse, Paul

    1998-01-01

    The X-Ray Spectrometer (XRS) instrument is part of the Astro-E mission scheduled to launch early in 2000. Its cryogenic system is required to cool a 32-element square array of x-ray microcalorimeters to 60-65 mK over a mission lifetime of at least 2 years. This is accomplished using an adiabatic demagnetization refrigerator (ADR) contained within a two-stage superfluid helium/solid neon cooler. Goddard Space Flight Center is providing the ADR and helium dewar. The flight system was assembled in Sept. 1997 and subjected to extensive thermal performance tests. This paper presents test results at both the system and component levels. In addition, results of the low temperature topoff performed in Japan with the engineering unit neon and helium dewars are discussed.

  17. Effect of kaolin addition on the performance of controlled low-strength material using industrial waste incineration bottom ash.

    PubMed

    Naganathan, Sivakumar; Razak, Hashim Abdul; Hamid, Siti Nadzriah Abdul

    2010-09-01

    Incineration of industrial waste produces large quantities of bottom ash which are normally sent to secured landfill, but is not a sustainable solution. Use of bottom ash in engineering applications will contribute to sustainability and generate revenue. One way of using the industrial waste incineration bottom ash is in controlled low-strength material (CLSM). Use of bottom ash in CLSM has problems related to bleeding and excessive strength development and so an additive has to be used to control bleeding and strength development. The main objective of this research is to study the effect of kaolin addition on the performance of CLSM made using industrial waste incineration bottom ash. CLSM mixes were made with bottom ash, cement, and refined kaolin. Various tests were performed on the CLSM in fresh and hardened states including compressive strength, water absorption, California bearing ratio (CBR) and the tests for concentration of leachable substances on the bleed and leachate. The compressive strength of CLSM tested ranged from 0.11 to 9.86 MPa. CBR values ranged from 6 to 46, and water absorption values from 12 to 36%. It was shown that the addition of kaolin delayed the initial setting time of CLSM mixtures, reduced bleeding, lowered the compressive strength, and increased the values of water absorption, sorption, and initial surface absorption. The CLSM tested did not have corrosivity. It was shown that the hardened CLSM was non hazardous, and the addition of kaolin increased the concentration of heavy metals and salts in the bleed and leachate.

  18. Effects of a phytogenic feed additive on growth performance and ileal nutrient digestibility in broiler chickens.

    PubMed

    Amad, A A; Männer, K; Wendler, K R; Neumann, K; Zentek, J

    2011-12-01

    A study was undertaken to examine the effects of a phytogenic feed additive (PFA) containing essential oils of thyme and star anise as lead active components on the growth performance and apparent ileal nutrient digestibility in broiler chickens. In total, 528 one-day-old Cobb male broilers were randomly divided into 4 dietary treatment groups with 6 replicate pens per treatment group (22 birds each). The dietary treatments were a control starter and grower basal diet without PFA or 150, 750, or 1,500 mg/kg of PFA. Body weight, weight gain, and feed intake were not significantly influenced by the feed additive, but the feed conversion ratio during the grower (22-42 d) and overall (1-42 d) periods improved linearly (P < 0.05) by the administration of PFA compared with that of the control diet. The average weights of the liver, heart, kidneys, and spleen were not significantly affected by the PFA. The results of the apparent ileal digestibility of crude ash, CP, crude fat, calcium, and phosphorus showed a linear increase (P < 0.05) related to the increase of PFA dose in the diet. Therefore, the means of digestibility of these nutrients were significantly higher in birds fed the PFA for all categories of age compared with the digestibility of these nutrients in the controls. In conclusion, the mode of action of the tested PFA can be explained by an improvement in the nutrient digestibility in the small intestine. The underlying physiological mechanisms, however, need to be characterized further.

  19. Laboratory endurance testing of a 25/75 sunflower oil-diesel fuel blend treated with fuel additives

    SciTech Connect

    Ziejewski, M.; Kaufman, K.R.; Tupa, R.C.

    1984-02-01

    The engine performance and durability effects of a barium smoke suppressant additive, Lubrizol 565, and an ashless polymeric additive, Lubrizol 552, in a 25-75 blend (v/v) of alkali refined sunflower oil with diesel fuel were investigated. The study was performed on a direct injected, turbocharged, and intercooled diesel engine. These additives were tested in an attempt to reduce carbon buildup problems observed while using an untreated 25-75 blend of sunflower oil and diesel fuel. Compared to the engine tests on the untreated 25-75 mixture, the barium smoke suppressant additive proved effective in cleaning the inside of injection nozzles (no needle sticking, no carbon build-up inside the orifices), reducing diesel exhaust smoke, and increasing engine power output. However, there was increased residue accumulation in the combustion chamber and on the exterior of the injection nozzle tips. The ashless dispersant additive also improved nozzle cleanliness but did not demonstrate any effect on engine power or cause excessive carbon buildup on the nozzle tips, top of the pistons, and cylinder head. The Lubrizol 552 dispersant looks very promising as an additive for vegetable oil diesel fuel blends for controlling excessive carbon and lacquer deposits.

  20. Effects of maternally exposed colouring food additives on cognitive performance in rats.

    PubMed

    Doguc, Duygu Kumbul; Ceyhan, Betul Mermi; Ozturk, Mustafa; Gultekin, Fatih

    2013-08-01

    Artificial food colourings and additives (AFCAs) have long been suggested to adversely affect the learning and behaviour in children. In this study, we aimed to provide additional data to clarify the possible side effects of colouring additives on behaviour and memory. We administered acceptable daily intake values of AFCAs as a mixture (Eritrosin, Ponceau 4R, Allura Red AC, Sunset Yellow FCF, Tartrazin, Amaranth, Brilliant Blue, Azorubin and Indigotin) to female rats before and during gestation and then tested their effects on behaviour and on spatial working memory in their offspring. Effects on spatial learning and memory were evaluated by Morris water maze, behavioural effects were evaluated by open-field test and forced swim test. Our results showed that commonly used artificial food colourings have no adverse effects on spatial working memory and did not create a depressive behaviour in offspring. But they showed a few significant effects on locomotor activity as AFCAs increased some parameters of locomotor activity.

  1. Standardization in Cryogenic Insulation Systems Testing and Performance Data

    NASA Astrophysics Data System (ADS)

    Fesmire, James E.

    The close relationship between industrial energy use and cryogenics drives the need for optimized thermal insulation systems. Emerging cryofuels usage is enabled by adequate isolation of the liquid hydrogen or liquefied natural gas from the ambient environment. Thermal performance data for the total insulation system, as rendered, are essential for both engineering designs and cost-benefit decisions involving comparisons among alternatives. These data are obtained through rigorous testing with suitable apparatus and repeatable methods. Properly defined terminology, analysis, and reporting are also vital. Advances in cryogenic insulation test apparatus and methods have led to the recent addition of two new technical standards of ASTM International: C1774 - Standard Guide for Thermal Performance Testing of Cryogenic InsulationSystems and C740 - Standard Guide for Evacuated Reflective Cryogenic Insulation. Among the different techniques described in the new standards is the cylindrical boiloff calorimeter for absolute heat measurement over the full range of vacuum pressure conditions. The details of this apparatus, test method, and data analysis are given. Benchmark thermal performance data, including effective thermal conductivity (ke) and heat flux (q) for the boundary temperatures of 293 K and 77 K, are given for a number of different multilayer insulation (MLI) systems in comparison with data for other commonly-used insulation systems including perlite powder, fiberglass, polyurethane foam, and aerogels.

  2. Test Anxiety and Performance on Reading Competency Tests.

    ERIC Educational Resources Information Center

    Stallworth-Clark, Rosemarie; Cochran, Jeff; Nolen, Martha T.; Tuggle, Durelle L.; Scott, Janice S.

    2000-01-01

    Describes a 20 item self-report psychometric scale that was used to assess test anxiety levels in 67 students. Reports that the higher the anxiety level, as measured by the Revised Test Anxiety Scale (RTA), the lower the score on a reading and writing competency exam taken subsequently, and that students who received extra time on the reading test…

  3. Effects of load on wingate test performances and reliability.

    PubMed

    Jaafar, Hamdi; Rouis, Majdi; Coudrat, Laure; Attiogbé, Elvis; Vandewalle, Henry; Driss, Tarak

    2014-12-01

    The purpose of this study was to examine the effects of 2 braking forces (8.7 and 11% of body mass, BM) on Wingate test performance, peak lactate ([La]pk), peak heart rate (HRpk), and rate of perceived exertion (RPE). Sixteen male physical education students (age: 22.7 ± 1.3 years, height: 1.81 ± 0.07 m, BM: 74.3 ± 9.6 kg) performed, in a randomized order, 2 Wingate tests at 8.7% BM and 2 Wingate tests at 11% BM on a Monark cycle ergometer on 4 separate sessions. The results showed that the reliability level of mechanical measures was not affected by the braking force and was relatively similar for each variable in both braking forces (0.886 < ICC < 0.985). In addition, peak power, mean power, fatigue slope, and RPE were significantly higher (8.2, 7.0, 11.9, and 4.1%, respectively, all < 0.05) using a braking force of 11% BM compared with 8.7% BM, whereas there was no significant effect of braking force on [La]pk and HRpk. In conclusion, the results of this study suggested that the reliability of the Wingate test does not depend on the used load, and a braking force of 11% BM is more optimal for power output during Wingate test in active adults.

  4. The development of a high intensity dance performance fitness test.

    PubMed

    Redding, Emma; Weller, Peter; Ehrenberg, Shantel; Irvine, Sarah; Quin, Edel; Rafferty, Sonia; Wyon, Matthew; Cox, Carol

    2009-01-01

    While there is currently a validated dance-specific exercise method of measuring aerobic fitness, no such test has been developed to measure high intensity capabilities in dance. The purpose of this study was to initiate an intermittent high intensity dance-specific fitness test. The test was designed to be able to observe changes in heart rate (HR), thereby allowing for a measurement of physical fitness at high intensities. Sixteen professional dancers (4 males and 12 females) volunteered to take part in this study. The fitness test protocol consists of movements that are representative of contemporary dance, and contains exercise and rest periods that mimic the intermittent nature of dance. The participants performed four trials. The physiological variables measured were HR (b.min(-1)) for each one minute bout of the four minute test for all trials, oxygen uptake (VO(2)) throughout the test, and end blood lactate (BLa mmol.L) for each trial. In addition, five of the participants undertook a maximal oxygen uptake treadmill test, and the scores obtained were compared with those from the dance test. Results show HR consistency across each one minute bout of the test and across each of the four trials of testing for all participants, indicating that the test is reliable. There was good reliability between bouts of each trial (typical error as % of CV = 1.5), intraclass "r" = 0.8, and good reliability between the four trials (typical error as % of CV = 2.1), intraclass "r" = 0.82. There were no significant differences between the maximal VO(2) and BLa scores established in the treadmill and dance tests, demonstrating validity. Thus, the results of this study indicate that the high intensity dance-specific test is a reliable and valid means of assessing and monitoring the cardiovascular fitness of dancers. The test allows dancers to be assessed within an environment that they are accustomed to (the studio), using a mode of exercise that is relevant (dance), and it is

  5. Safety Performance of Airborne Separation: Preliminary Baseline Testing

    NASA Technical Reports Server (NTRS)

    Consiglio, Maria C.; Hoadley, Sherwood T.; Wing, David J.; Baxley, Brian T.

    2007-01-01

    The Safety Performance of Airborne Separation (SPAS) study is a suite of Monte Carlo simulation experiments designed to analyze and quantify safety behavior of airborne separation. This paper presents results of preliminary baseline testing. The preliminary baseline scenario is designed to be very challenging, consisting of randomized routes in generic high-density airspace in which all aircraft are constrained to the same flight level. Sustained traffic density is varied from approximately 3 to 15 aircraft per 10,000 square miles, approximating up to about 5 times today s traffic density in a typical sector. Research at high traffic densities and at multiple flight levels are planned within the next two years. Basic safety metrics for aircraft separation are collected and analyzed. During the progression of experiments, various errors, uncertainties, delays, and other variables potentially impacting system safety will be incrementally introduced to analyze the effect on safety of the individual factors as well as their interaction and collective effect. In this paper we report the results of the first experiment that addresses the preliminary baseline condition tested over a range of traffic densities. Early results at five times the typical traffic density in today s NAS indicate that, under the assumptions of this study, airborne separation can be safely performed. In addition, we report on initial observations from an exploration of four additional factors tested at a single traffic density: broadcast surveillance signal interference, extent of intent sharing, pilot delay, and wind prediction error.

  6. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Reasonable and representative tests and recordkeeping requirements-additional requirements. 1631.32 Section 1631.32 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF...

  7. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Reasonable and representative tests and recordkeeping requirements-additional requirements. 1631.32 Section 1631.32 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF...

  8. Biodegradability testing of synthetic ester lubricants--effects of additives and usage.

    PubMed

    Eisentraeger, Adolf; Schmidt, Martin; Murrenhoff, Hubertus; Dott, Wolfgang; Hahn, Stefan

    2002-07-01

    The optimised biodegradability test system "O2/CO2 Headspace Test with GC-TCD" is used for the assessment of synthetic ester lubricants. The effects of both additives and usage on biodegradability are examined and discussed. Ester based cutting fluids and hydraulic fluids with and without additives are used under defined conditions at machine tools and hydraulic and plain bearing test benches. The lubricants are characterised additionally with respect to kinematic viscosity, acidity and elemental composition. Furthermore, a formulated mineral oil is characterised before and after usage at an hydraulic test bench. The results clearly show that the mineral oil is far less biodegradable than the ester oils and that their biodegradability is not affected by usage. Biodegradability of the ester oils is mainly depending on the characteristics of the base fluids and not affected by the additives. Antioxidants are influencing stability respectively biodegradability indirectly, since they prevent oxopolymerisation effects. Other effects of usage on biodegradation are not detected. In this context, the antioxidants ensure ready biodegradability and have a positive effect on the environmental fate of synthetic ester lubricants.

  9. Testing for departures from additivity in mixtures of perfluoroalkyl acids (PFAAs)

    EPA Science Inventory

    This study is a follow-up to a paper by Carr, et al. that determined a design structure to optimally test for departures from additivity in a fixed ratio mixture of four perfluoroalkyl acids (PFAAs) using an in vitro transiently-transfected COS- 1 PPARa reporter model with an NHA...

  10. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  11. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  12. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  13. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  14. 30 CFR 77.102 - Tests for methane; oxygen deficiency; qualified person, additional requirement.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tests for methane; oxygen deficiency; qualified... methane; oxygen deficiency; qualified person, additional requirement. Notwithstanding the provisions of... and oxygen deficiency unless he has demonstrated to the satisfaction of an authorized...

  15. Integrated Performance Testing Workshop - Supplemental Materials (Scripts and Procedures)

    SciTech Connect

    Baum, Gregory A.

    2014-02-01

    A variety of performance tests are described relating to: Material Transfers; Emergency Evacuation; Alarm Response Assessment; and an Enhanced Limited Scope Performance Test (ELSPT). Procedures are given for: nuclear material physical inventory and discrepancy; material transfers; and emergency evacuation.

  16. Test Competency as Related to Classroom Performance.

    ERIC Educational Resources Information Center

    Farmer, Walter A.; And Others

    This study of student teachers in high school mathematics and science classrooms compares their teaching behaviors and their scores from three pencil-and-paper tests. Data analysis indicates a relative independence between the ratings of teacher classroom behavior and scores on the pencil-and-paper tests. There was little consistent relationship…

  17. Effect of Fuel Additives on Spray Performance of Alternative Jet Fuels

    NASA Astrophysics Data System (ADS)

    Kannaiyan, Kumaran; Sadr, Reza

    2015-11-01

    Role of alternative fuels on reducing the combustion pollutants is gaining momentum in both land and air transport. Recent studies have shown that addition of nanoscale metal particles as fuel additives to liquid fuels have a positive effect not only on their combustion performance but also in reducing the pollutant formation. However, most of those studies are still in the early stages of investigation with the addition of nanoparticles at low weight percentages. Such an addition can affect the hydrodynamic and thermo-physical properties of the fuel. In this study, the near nozzle spray performance of gas-to-liquid jet fuel with and without the addition of alumina nanoparticles are investigated at macro- and microscopic levels using optical diagnostic techniques. At macroscopic level, the addition of nanoparticles is seen to enhance the sheet breakup process when compared to that of the base fuel. Furthermore, the microscopic spray characteristics such as droplet size and velocity are also found to be affected. Although the addition of nanoscale metal particles at low weight percentages does not affect the bulk fluid properties, the atomization process is found to be affected in the near nozzle region. Funded by Qatar National Research Fund.

  18. 10 CFR 26.168 - Blind performance testing.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... the blind performance test samples submitted to the laboratory must be positive for one or more drugs... blind performance test samples to the HHS-certified laboratory. (1) During the initial 90-day period of... licensee or other entity shall submit blind performance test samples to each HHS-certified laboratory...

  19. Metrology test object for dimensional verification in additive manufacturing of metals for biomedical applications.

    PubMed

    Teeter, Matthew G; Kopacz, Alexander J; Nikolov, Hristo N; Holdsworth, David W

    2015-01-01

    Additive manufacturing continues to increase in popularity and is being used in applications such as biomaterial ingrowth that requires sub-millimeter dimensional accuracy. The purpose of this study was to design a metrology test object for determining the capabilities of additive manufacturing systems to produce common objects, with a focus on those relevant to medical applications. The test object was designed with a variety of features of varying dimensions, including holes, cylinders, rectangles, gaps, and lattices. The object was built using selective laser melting, and the produced dimensions were compared to the target dimensions. Location of the test objects on the build plate did not affect dimensions. Features with dimensions less than 0.300 mm did not build or were overbuilt to a minimum of 0.300 mm. The mean difference between target and measured dimensions was less than 0.100 mm in all cases. The test object is applicable to multiple systems and materials, tests the effect of location on the build, uses a minimum of material, and can be measured with a variety of efficient metrology tools (including measuring microscopes and micro-CT). Investigators can use this test object to determine the limits of systems and adjust build parameters to achieve maximum accuracy.

  20. Influence of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission.

    PubMed

    Keskin, Ali; Gürü, Metin; Altiparmak, Duran

    2008-09-01

    The purpose of this study is to investigate influences of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission. Tall oil resinic acids were reacted with MgO and MoO(2) stoichiometrically for the production of metal-based fuel additives (combustion catalysts). The metal-based additives were added into tall oil biodiesel (B60) at the rate of 4 micromol/l, 8 micromol/l and 12 micromol/l for preparing test fuels. In general, both of the metal-based additives improved flash point, pour point and viscosity of the biodiesel fuel, depending on the rate of additives. A single cylinder DI diesel engine was used in the tests. Engine performance values did not change significantly with biodiesel fuels, but exhaust emission profile was improved. CO emissions and smoke opacity decreased by 56.42% and by 30.43%, respectively. In general, low NO(x) and CO(2) emissions were measured with the biodiesel fuels.

  1. 40 CFR 60.8 - Performance tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... access to sampling platform(s). (4) Utilities for sampling and testing equipment. (f) Unless otherwise... there is 95 percent confidence that 90 percent of well qualified labs will produce future results...

  2. Boosting the Performance of Ionic-Liquid-Based Supercapacitors with Polar Additives

    SciTech Connect

    Liu, Kun; Wu, Jianzhong

    2016-10-05

    Recent years have witnessed growing interests in both the fundamentals and applications of electric double layer capacitors (EDLCs), also known as supercapacitors. A number of strategies have been explored to optimize the device performance in terms of both the energy and power densities. Because the properties of electric double layers (EDL) are sensitive to ion distributions in the close vicinity of the electrode surfaces, the supercapacitor performance is sensitive to both the electrode pore structure and the electrolyte composition. In this paper, we study the effects of polar additives on EDLC capacitance using the classical density functional theory within the framework of a coarse-grained model for the microscopic structure of the porous electrodes and room-temperature ionic liquids. The theoretical results indicate that a highly polar, low-molecular-weight additive is able to drastically increase the EDLC capacitance at low bulk concentration. Additionally, the additive is able to dampen the oscillatory dependence of the capacitance on the pore size, thereby boosting the performance of amorphous electrode materials. Finally, the theoretical predictions are directly testable with experiments and provide new insights into the additive effects on EDL properties.

  3. Boosting the Performance of Ionic-Liquid-Based Supercapacitors with Polar Additives

    DOE PAGES

    Liu, Kun; Wu, Jianzhong

    2016-10-05

    Recent years have witnessed growing interests in both the fundamentals and applications of electric double layer capacitors (EDLCs), also known as supercapacitors. A number of strategies have been explored to optimize the device performance in terms of both the energy and power densities. Because the properties of electric double layers (EDL) are sensitive to ion distributions in the close vicinity of the electrode surfaces, the supercapacitor performance is sensitive to both the electrode pore structure and the electrolyte composition. In this paper, we study the effects of polar additives on EDLC capacitance using the classical density functional theory within themore » framework of a coarse-grained model for the microscopic structure of the porous electrodes and room-temperature ionic liquids. The theoretical results indicate that a highly polar, low-molecular-weight additive is able to drastically increase the EDLC capacitance at low bulk concentration. Additionally, the additive is able to dampen the oscillatory dependence of the capacitance on the pore size, thereby boosting the performance of amorphous electrode materials. Finally, the theoretical predictions are directly testable with experiments and provide new insights into the additive effects on EDL properties.« less

  4. Combat System Testing, Training and Performance Monitoring,

    DTIC Science & Technology

    1986-01-01

    implemented now, while the CG 47 Class AEGIS Cmbat Training System/Operational Readiness Test System (ACTS/ORTS) and the DDG 993 Class Combat Simulation Test...capabilities of the AN/SSQ-91 CSTS presently in the fleet in DDG 993 Class ships, describes similar systems under. .- contract for LHD I and MCM I ship...1-1 1.3 DDG 993 CLASS CSTS ............................................ 1-1 1.4 LHD I CSTS

  5. Performance on Addition and Subtraction Problems: Results from Individual Interviews - Sandy Bay Study.

    ERIC Educational Resources Information Center

    Romberg, Thomas A.; And Others

    The purpose of this study was to relate children's cognitive processing capabilities and their grade level to their performance and to the strategies they used when working addition and subtraction problems. From two sets of data which assessed memory capacity and cognitive processing capacities, six groups of children with different cognitive…

  6. Strategies and Performance in Elementary Students' Three-Digit Mental Addition

    ERIC Educational Resources Information Center

    Csíkos, Csaba

    2016-01-01

    The focus of this study is the relationship between students' performance in mental calculation and the strategies they use when solving three-digit mental addition problems. The sample comprises 78 4th grade students (40 boys and 38 girls). Their mean age was 10 years and 4 months. The main novelties of the current research include (1)…

  7. Performance testing and results of the first Etec CORE-2564

    NASA Astrophysics Data System (ADS)

    Franks, C. Edward; Shikata, Asao; Baker, Catherine A.

    1993-03-01

    In order to be able to write 64 megabit DRAM reticles, to prepare to write 256 megabit DRAM reticles and in general to meet the current and next generation mask and reticle quality requirements, Hoya Micro Mask (HMM) installed in 1991 the first CORE-2564 Laser Reticle Writer from Etec Systems, Inc. The system was delivered as a CORE-2500XP and was subsequently upgraded to a 2564. The CORE (Custom Optical Reticle Engraver) system produces photomasks with an exposure strategy similar to that employed by an electron beam system, but it uses a laser beam to deliver the photoresist exposure energy. Since then the 2564 has been tested by Etec's standard Acceptance Test Procedure and by several supplementary HMM techniques to insure performance to all the Etec advertised specifications and certain additional HMM requirements that were more demanding and/or more thorough than the advertised specifications. The primary purpose of the HMM tests was to more closely duplicate mask usage. The performance aspects covered by the tests include registration accuracy and repeatability; linewidth accuracy, uniformity and linearity; stripe butting; stripe and scan linearity; edge quality; system cleanliness; minimum geometry resolution; minimum address size and plate loading accuracy and repeatability.

  8. 42 CFR 493.1487 - Condition: Laboratories performing high complexity testing; testing personnel.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... testing; testing personnel. 493.1487 Section 493.1487 Public Health CENTERS FOR MEDICARE & MEDICAID... REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing High Complexity Testing § 493.1487 Condition: Laboratories performing high complexity testing; testing personnel. The laboratory has...

  9. 42 CFR 493.1487 - Condition: Laboratories performing high complexity testing; testing personnel.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... testing; testing personnel. 493.1487 Section 493.1487 Public Health CENTERS FOR MEDICARE & MEDICAID... REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing High Complexity Testing § 493.1487 Condition: Laboratories performing high complexity testing; testing personnel. The laboratory has...

  10. 42 CFR 493.1487 - Condition: Laboratories performing high complexity testing; testing personnel.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... testing; testing personnel. 493.1487 Section 493.1487 Public Health CENTERS FOR MEDICARE & MEDICAID... REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing High Complexity Testing § 493.1487 Condition: Laboratories performing high complexity testing; testing personnel. The laboratory has...

  11. 42 CFR 493.1487 - Condition: Laboratories performing high complexity testing; testing personnel.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... testing; testing personnel. 493.1487 Section 493.1487 Public Health CENTERS FOR MEDICARE & MEDICAID... REQUIREMENTS Personnel for Nonwaived Testing Laboratories Performing High Complexity Testing § 493.1487 Condition: Laboratories performing high complexity testing; testing personnel. The laboratory has...

  12. Alkyl Pyrocarbonate Electrolyte Additives for Performance Enhancement of Li Ion Cells

    NASA Technical Reports Server (NTRS)

    Smart, M. C.; Ratnakumar, B. V.; Surampudi, S.

    2000-01-01

    Lithium ion rechargeable batteries are being developed for various aerospace applications under a NASA-DoD Interagency program. These applications require further improvements in several areas, specifically in the cycle life for LEO and GEO satellites and in the low temperature performance for the Mars Lander and Rover missions. Accordingly, we have been pursuing research studies to achieve improvement in the low temperature performance, long cycle life and active life of Li ion cells. The studies are mainly focused on electrolytes, to identify newer formulations of new electrolyte additives to enhance Li permeability (at low temperatures) and stability towards the electrode. The latter approach is particularly aimed at the formation suitable SEI (solid electrolyte interphase) on carbon electrodes. In this paper, we report the beneficial effect of using alkyl pyrocarbonates as electrolyte additives to improve the low temperature performance of Li ion cells.

  13. Effect of Ag Addition on the Electrochemical Performance of Cu10Al in Artificial Saliva

    PubMed Central

    Salgado-Salgado, R. J.; Sotelo-Mazon, O.; Rodriguez-Diaz, R. A.; Salinas-Solano, G.

    2016-01-01

    In this work we proposed to evaluate the corrosion resistance of four different alloys by electrochemical techniques, a binary alloy Cu10Al, and three ternary alloys Cu10Al-xAg (x = 5, 10, and 15 wt.%) to be used like biomaterials in dental application. Biomaterials proposed were tested in artificial saliva at 37°C for 48 h. In addition, pure metals Cu, Al, Ag, and Ti as reference materials were evaluated. In general the short time tests indicated that the Ag addition increases the corrosion resistance and reduces the extent of localized attack of the binary alloy. Moreover, tests for 48 hours showed that the Ag addition increases the stability of the passive layer, thereby reducing the corrosion rate of the binary alloy. SEM analysis showed that Cu10Al alloy was preferably corroded by grain boundaries, and the Ag addition modified the form of attack of the binary alloy. Cu-rich phases reacted with SCN− anions forming a film of CuSCN, and the Ag-rich phase is prone to react with SCN− anions forming AgSCN. Thus, binary and ternary alloys are susceptible to tarnish in the presence of thiocyanate ions. PMID:27660601

  14. Imaging performance tests of diffractive optical system

    NASA Astrophysics Data System (ADS)

    Jiao, Jianchao; Su, Yun; Wang, Baohua; Wang, Chao; Zhang, Yue; Jin, Jiangao

    2016-10-01

    Diffractive optical imaging is a new method to realize high-resolution imaging from geostationary orbit(GEO). Technical advantages of diffractive optical imaging is analyzed in the field of space optics. For application of super large diameter space optical system, the system scheme and a new achromatic method is proposed. An imaging system is developed and tested, the result of optical system wavefront is 0.169λ(RMS), optical system MTF is 0.85, and the imaging system MTF is 0.19. Test results show the new achromatic method is feasible. The above conclusions have reference significance for the development of super large diameter diffractive optical imaging system.

  15. Modified MTS MRB500 CATALYST PERFORMANCE TEST

    SciTech Connect

    Glen R. Longhurst; Robert J. Pawelko

    2008-10-01

    An experiment was conducted to determine if the oxygen supply in a CuO catalyst considered for use in the TMIST-2 irradiation test would be sufficient to convert all the hydrogen isotopes coming from the irradiation test to water. A mixture of 2% H2 in Ar was supplied to a modified MRB 500 stack m onitor from Mound Techology Solutions, Miamisburg, OH. It was found that the catalyst could convert 3.75E-03 moles of H2 before losing its effectiveness. Conversion was found to begin at a catalyst temperature of about 220 deg C and to be fully effective at about 300 deg C.

  16. Evaluating mixtures of 14 hygroscopic additives to improve antibody microarray performance.

    PubMed

    Bergeron, Sébastien; Laforte, Veronique; Lo, Pik-Shan; Li, Huiyan; Juncker, David

    2015-11-01

    Microarrays allow the miniaturization and multiplexing of biological assays while only requiring minute amounts of samples. As a consequence of the small volumes used for spotting and the assays, evaporation often deteriorates the quality, reproducibility of spots, and the overall assay performance. Glycerol is commonly added to antibody microarray printing buffers to decrease evaporation; however, it often decreases the binding of antibodies to the surface, thereby negatively affecting assay sensitivity. Here, combinations of 14 hygroscopic chemicals were used as additives to printing buffers for contact-printed antibody microarrays on four different surface chemistries. The ability of the additives to suppress evaporation was quantified by measuring the residual buffer volume in open quill pins over time. The seven best additives were then printed either individually or as a 1:1 mixture of two additives, and the homogeneity, intensity, and reproducibility of both the spotted protein and of a fluorescently labeled analyte in an assay were quantified. Among the 28 combinations on the four slides, many were found to outperform glycerol, and the best additive mixtures were further evaluated by changing the ratio of the two additives. We observed that the optimal additive mixture was dependent on the slide chemistry, and that it was possible to increase the binding of antibodies to the surface threefold compared to 50 % glycerol, while decreasing whole-slide coefficient of variation to 5.9 %. For the two best slides, improvements were made for both the limit of detection (1.6× and 5.9×, respectively) and the quantification range (1.2× and 2.1×, respectively). The additive mixtures identified here thus help improve assay reproducibility and performance, and might be beneficial to all types of microarrays that suffer from evaporation of the printing buffers.

  17. Influence of electrolyte co-additives on the performance of dye-sensitized solar cells

    PubMed Central

    2011-01-01

    The presence of specific chemical additives in the redox electrolyte results in an efficient increase of the photovoltaic performance of dye-sensitized solar cells (DSCs). The most effective additives are 4-tert-butylpyridine (TBP), N-methylbenzimidazole (NMBI) and guanidinium thiocyanate (GuNCS) that are adsorbed onto the photoelectrode/electrolyte interface, thus shifting the semiconductor's conduction band edge and preventing recombination with triiodides. In a comparative work, we investigated in detail the action of TBP and NMBI additives in ionic liquid-based redox electrolytes with varying iodine concentrations, in order to extract the optimum additive/I2 ratio for each system. Different optimum additive/I2 ratios were determined for TBP and NMBI, despite the fact that both generally work in a similar way. Further addition of GuNCS in the optimized electrolytic media causes significant synergistic effects, the action of GuNCS being strongly influenced by the nature of the corresponding co-additive. Under the best operation conditions, power conversion efficiencies as high as 8% were obtained. PMID:21711833

  18. Radial distribution functions of non-additive hard sphere mixtures via Percus' test particle route.

    PubMed

    Hopkins, Paul; Schmidt, Matthias

    2011-08-17

    Using fundamental density functional theory we calculate the partial radial distribution functions, g(ij)(r), of a binary non-additive hard sphere mixture using either Percus' test particle approach or inversion of the analytic structure factor obtained via the Ornstein-Zernike route. We find good agreement between the theoretical results and Monte Carlo simulation data for both positive and moderate negative non-additivities. We investigate the asymptotic, [Formula: see text], decay of the g(ij)(r) and show that this agrees with the analytic analysis of the contributions to the partial structure factors in the plane of complex wavevectors. We find the test particle density profiles to be free of unphysical artefacts, contrary to earlier reports.

  19. CHROMagar Salmonella Detection Test Kit. Performance Tested Method 020502.

    PubMed

    Webb, Katana; Ritter, Vicki

    2009-01-01

    BBL CHROMagar Salmonella was evaluated by an external food testing laboratory for the recovery of Salmonella in peanut butter using the U.S. Food and Drug Administration's Bacteriological Analytical Manual (FDA-BAM) procedure. The peanut butter was found to be negative for the presence of Salmonella and, therefore, was seeded with heat-stressed Salmonella at target concentrations of 0.2 and 2 CFU/25 g. The Salmonella-seeded samples remained at room temperature for 14 days before analysis to stabilize the Salmonella in the food environment. Twenty 25 g test portions from each seeded level and five 25 g samples of uninoculated control samples were processed using enrichment broths as outlined in the FDA-BAM procedure. BBL CHROMagar Salmonella-prepared plates were evaluated with the FDA reference method media (bismuth sulfite, xylose lysine desoxycholate, and Hektoen enteric agars). Fractionally positive results were obtained from the lower inoculum level of peanut butter samples. Five positive cultures were recovered from both the BBL CHROMagar Salmonella and reference methods. The two methods gave identical results for all cultures resulting in a method agreement of 100%. McNemar's chi2 test, which assesses the evidence for difference in marginal proportions between two methods, could not be evaluated because it requires one or more discrepant cultures. However, because there were no discrepant cultures, the marginal proportions for the two methods were identical; therefore, there is no evidence of a difference between the methods. This study demonstrates that the results from BBL CHROMagar Salmonella are comparable to the three reference method media for the detection of Salmonella in peanut butter using the FDA-BAM procedures.

  20. Ultimate strength performance of tankers associated with industry corrosion addition practices

    NASA Astrophysics Data System (ADS)

    Kim, Do Kyun; Kim, Han Byul; Zhang, Xiaoming; Li, Chen Guang; Paik, Jeom Kee

    2014-09-01

    In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR), Common Structural Rules (CSR), and harmonised Common Structural Rules (CSRH) are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS), and Time-Dependent Corrosion Wastage Model (TDCWM). To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures

  1. Polydimethylsiloxane as a Macromolecular Additive for Enhanced Performance of Molecular Bulk Heterojunction Organic Solar Cells

    SciTech Connect

    Graham, Kenneth R.; Mei, Jianguo; Stalder, Romain; Shim, Jae Won; Cheun, Hyeunseok; Steffy, Fred; So, Franky; Kippelen, Bernard; Reynolds, John R.

    2011-03-15

    The effect of the macromolecular additive, polydimethylsiloxane (PDMS), on the performance of solution processed molecular bulk heterojunction solar cells is investigated, and the addition of PDMS is shown to improve device power conversion efficiency by ~70% and significantly reduce cell-to-cell variation, from a power conversion efficiency of 1.25 ± 0.37% with no PDMS to 2.16 ± 0.09% upon the addition of 0.1 mg/mL PDMS to the casting solution. The cells are based on a thiophene and isoindigo containing oligomer as the electron donor and [6,6]-phenyl-C61 butyric acid methyl ester (PC61BM) as the electron acceptor. PDMS is shown to have a strong influence on film morphology, with a significant decrease in film roughness and feature size observed. The morphology change leads to improved performance parameters, most notably an increase in the short circuit current density from 4.3 to 6.8 mA/cm2 upon addition of 0.1 mg/mL PDMS. The use of PDMS is of particular interest, as this additive appears frequently as a lubricant in plastic syringes commonly used in device fabrication; therefore, PDMS may unintentionally be incorporated into device active layers.

  2. Dental air turbine handpiece performance testing.

    PubMed

    Dyson, J E; Darvell, B W

    1995-10-01

    Air turbine handpieces are expected to continue to be widely used as the main means of carrying out dental cutting work and scope exists for further design improvements. An understanding of the theoretical principles governing the performance of these devices seems essential for the systematic development of better handpiece designs and methods of specification. Furthermore, for experimental work on cutting behaviour with air turbine equipment, this knowledge is required for appropriate characterization of the performance of the particular handpiece used with respect to actual rates of energy disposition. The literature relating to air turbine handpiece performance is critically reviewed to assess currently available methods of measuring important variables such as speed, torque, and power. In this, consideration is given to the current state of knowledge of the influence on these variables of air pressure, flow and turbine design features. It is apparent that, although various measurement methods have been described and data for individual handpieces published, no attempt has yet been made to explore the functional relationships that exist between the variables. It is concluded that there is a need to identify the factors influencing turbine performance, to develop measurement systems which would provide adequate accuracy and precision and then to investigate the functional relationships between these relevant variables.

  3. The effect of alkaline additives on the performance of surfactant systems designed to recover light oils

    SciTech Connect

    French, T.R.; Josephson, C.B.; Evans, D.B.

    1991-02-01

    Surfactant flooding is flexible because of the ability to optimize formulations for a wide range of reservoir conditions and crude oil types. The objective for this work was to determine if the addition of alkaline additives will allow the design of surfactant formulations that are effective for the recovery of crude oil, while, at the same time, maintaining the surfactant concentration at a much lower level than has previously been used for micellar flooding. Specifically, the focus of the work was on light, midcontinent crudes that typically have very low acid contents. These oils are typical of much of the midcontinent resource. The positive effect of alkaline additives on the phase behavior of the surfactant formulations and acidic crude oils is well known. The extension to nonacidic and slightly acidic oils is not obvious. Three crude oils, a variety of commercial surfactants, and several alkaline additives were tested. The oils had acid numbers that ranged from 0.13, which is quite low, to less than 0.01 mg KOH/g of oil. Alkaline additives were found to be very effective in recovering Delaware-Childers (OK) oil at elevated temperatures, but much less effective at reservoir temperatures. Alkaline additives were very effective with Teapot Dome (WY) oil. With Teapot Dome oil, surfactant/alkali systems produced ultralow IFT values and recovered 60% of the residual oil that remained after waterflooding. The effect of alkaline additives on recovering Hepler (KS) oil was minimal. The results of this work indicate that alkaline additives do have merit for use in surfactant flooding of low acid crude oils; however, no universal statement about applicability can be made. Each oil behaves differently, with this treatment, and the effect of alkaline additives must be determined (at reservoir conditions) for each oil. 23 refs., 13 figs., 3 tabs.

  4. Feasibility Investigation for Performing Fireball Temperature Tests

    NASA Technical Reports Server (NTRS)

    Tapphorn, Ralph M.; Kurtz, Joe

    1997-01-01

    NASA Johnson Space Center White Sands Test Facility (WSTF) was requested by the Launch Abort Subpanel and the Power Systems Subpanel of the Interagency Nuclear Safety Review Panel to investigate the feasibility of using spectroscopic techniques to measure propellant fireball gas temperatures. This report outlines the modeling and experimental approaches and results of this investigation. Descriptions of the theoretical particle temperature and mass effusion models are presented along with the results of the survivability of small plutonium dioxide (less than or equal to 1000 microns diameter) particles entrained in various propellant fireball scenarios. The experimental test systems used to measure the hydroxide radical, water, and particle graybody spectral emissions and absorptions are discussed. Spectral results along with temperatures extracted by analyzing the spectral features are presented for the flames investigated in the laboratory environment. Methods of implementing spectroscopic measurements for future testing using the WSTF Large-scale Hydrogen/Oxygen Explosion Facility are discussed, and the accuracy expected for these measurements is estimated from laboratory measurements.

  5. Antisolvent precipitation of novel xylitol-additive crystals to engineer tablets with improved pharmaceutical performance.

    PubMed

    Kaialy, Waseem; Maniruzzaman, Mohammad; Shojaee, Saeed; Nokhodchi, Ali

    2014-12-30

    The purpose of this work was to develop stable xylitol particles with modified physical properties, improved compactibility and enhanced pharmaceutical performance without altering polymorphic form of xylitol. Xylitol was crystallized using antisolvent crystallization technique in the presence of various hydrophilic polymer additives, i.e., polyethylene glycol (PEG), polyvinylpyrrolidone (PVP) and polyvinyl alcohol (PVA) at a range of concentrations. The crystallization process did not influence the stable polymorphic form or true density of xylitol. However, botryoidal-shaped crystallized xylitols demonstrated different particle morphologies and lower powder bulk and tap densities in comparison to subangular-shaped commercial xylitol. Xylitol crystallized without additive and xylitol crystallized in the presence of PVP or PVA demonstrated significant improvement in hardness of directly compressed tablets; however, such improvement was observed to lesser extent for xylitol crystallized in the presence of PEG. Crystallized xylitols produced enhanced dissolution profiles for indomethacin in comparison to original xylitol. The influence of additive concentration on tablet hardness was dependent on the type of additive, whereas an increased concentration of all additives provided an improvement in the dissolution behavior of indomethacin. Antisolvent crystallization using judiciously selected type and concentration of additive can be a potential approach to prepare xylitol powders with promising physicomechanical and pharmaceutical properties.

  6. Distraction produces over-additive increases in the degree to which alcohol impairs driving performance

    PubMed Central

    Van Dyke, Nicholas A.; Fillmore, Mark T.

    2015-01-01

    Rationale Research indicates that alcohol intoxication and increased demands on drivers’ attention from distractions (e.g. passengers and cell phones) contribute to poor driving performance and increased rates of traffic accidents and fatalities. Objectives The present study examined the separate and combined effects of alcohol and distraction on simulated driving performance at blood alcohol concentrations (BrACs) below the legal driving limit in the United States (i.e. 0.08%). Methods Fifty healthy adult drivers (36 men and 14 women) were tested in a driving simulator following a 0.65 g/kg dose of alcohol and a placebo. Drivers completed two drive tests; a distracted drive, which included a two-choice detection task, and an undistracted control drive. Multiple indicators of driving performance, such as drive speed, within-lane deviation, steering rate, and lane exceedances were measured. Results Alcohol and distraction each impaired measures of driving performance. Moreover, the magnitude of alcohol impairment was increased by at least two-fold when tested under the distracting versus the undistracted condition. Conclusions The findings highlight the need for a clearer understanding of how common distractions impact intoxicated drivers, especially at BrACs that are currently legal for driving in the United States. PMID:26349918

  7. Effect of additive on alfalfa silage fermentation characteristics and feedlot performance of steers.

    PubMed

    Mader, T L; Britton, R A; Krause, V E; Pankaskie, D E

    1985-07-01

    In each of two trials four large plastic bags were filled with approximately 72 mt of first cutting, early bloom alfalfa (35% dry matter). Fresh alfalfa in two bags was treated with .5 kg/metric ton of a commercial silage additive (Silo-Best). Two bags were left untreated. When compared with steers fed untreated alfalfa silage, weight gains, intakes, and feed efficiencies were not significantly (P greater than .05) altered for steers fed treated silage. However, laboratory analysis showed silage treatment increased in vitro dry matter digestibility (57.0 versus 60.6%) and decreased silage pH (4.98 versus 4.83). Concentrations of propionic and butyric acid were decreased by the additive. Data suggest that anaerobic fermentation was enhanced with the additive. Slight but significant improvements of silage in vitro dry matter digestibility, obtained by treating alfalfa silage with the inoculant-type preservative, did not result in improved performance in feeding trials.

  8. Performance test results of ETS-6 Ni-Cd cells

    NASA Technical Reports Server (NTRS)

    Nakatani, Kensuke; Yano, Y.; Kuwajima, S.; Kusawake, Hiroaki

    1994-01-01

    The topics covered are presented in viewgraph form and include the following: development schedule; main specification; cell design; production flow; acceptance test (1); acceptance test (2); cell weight; 20 C performance; capacity; overcharge pressure; end of charge voltage; -5 C performance; ETS-VI simulation cycle test; and battery storage.

  9. Experimental investigations of the hydrogen addition effects on diesel engine performance

    NASA Astrophysics Data System (ADS)

    Mirica, I.; Pana, C.; Negurescu, N.; Cernat, A.; Nutu, C.

    2016-08-01

    In the global content regarding the impact on the environmental of the gases emissions resulted from the fossil fuels combustion, an interest aspect discussed on the 21st Session of the Conference of the Parties from the 2015 Paris Climate Conference and the gradual diminution of the worldwide oil reserves contribute to the necessity of searching of alternative energy from durable and renewable resources. At the use of hydrogen as addition in air to diesel engine, the level of CO, HC and smoke from the exhaust gases will decrease due to the improvement of the combustion process. At low and medium partial loads and low hydrogen energetic ratios used the NOX emission level can decrease comparative to classic diesel engine. The hydrogen use as fuel for diesel engine leads to the improving of the energetic and emissions performance of the engine due to combustion improvement and reduction of carbon content. The paper presents, in a comparative way, results of the experimental researches carried on a truck compression ignition engine fuelled with diesel fuel and with hydrogen diesel fuel and hydrogen as addition in air at different engine operation regimes. The results obtained during experimental investigations show better energetic and pollution performance of the engine fuelled with hydrogen as addition in air comparative to classic engine. The influences of hydrogen addition on engine operation are shown.

  10. Improved performance of air-cathode microbial fuel cell through additional Tween 80

    NASA Astrophysics Data System (ADS)

    Wen, Qing; Kong, Fanying; Ma, Fang; Ren, Yueming; Pan, Zhongcheng

    The ability of electron transfer from microbe cell to anode electrode plays a key role in microbial fuel cell (MFC). This study explores a new approach to improve the MFC performance and electron transfer rate through addition of Tween 80. Results demonstrate that, for an air-cathode MFC operating on 1 g L -1 glucose, when the addition of Tween 80 increases from 0 to 80 mg L -1, the maximum power density increases from 21.5 to 187 W m -3 (0.6-5.2 W m -2), the corresponding current density increases from 1.8 to 17 A m -2, and the resistance of MFC decreases from 27.0 to 5.7 Ω. Electrochemical impedance spectroscopy (EIS) analysis suggests that the improvement of overall performance of the MFC can be attributed to the addition of Tween 80. The high power density achieved here may be due to the increase of permeability of cell membranes by addition of Tween 80, which reduces the electron transfer resistance through the cell membrane and increases the electron transfer rate and number, consequently enhances the current and power output. A promising way of utilizing surfactant to improve energy generation of MFC is demonstrated.

  11. The Consequence of Consequence: Motivation, Anxiety, and Test Performance.

    ERIC Educational Resources Information Center

    Wolf, Lisa F.; Smith, Jeffrey K.

    1995-01-01

    The relationships of test consequence, motivation, anxiety, and performance were studied with 158 undergraduates taking a child development course. Results indicated that test consequence (grade or no grade) had a strong influence on motivation and a modest influence on performance. Motivation and anxiety had opposite effects on performance. (SLD)

  12. Influence of supplemental heat addition on performance of pilot-scale bioreactor landfills.

    PubMed

    Abdallah, Mohamed; Kennedy, Kevin; Narbaitz, Roberto; Warith, Mostafa; Sartaj, Majid

    2014-02-01

    Implementation of supplemental heat addition as a means of improving bioreactor landfill performance was investigated. The experimental work was conducted with two pilot-scale bioreactor setups (control cell and heated cell) operated for 280 days. Supplemental heat was introduced by recirculating leachate heated up to 35 °C compared to the control which used similar quantities of leachate at room temperature (21 ± 1 °C). The temporal and spatial effects of recirculating heated leachate on the landfill internal temperature were determined, and performance was assessed in terms of leachate parameters and biogas production. Recirculation of heated leachate helped establish balanced anaerobic microbial consortia that led to earlier (70 days) and greater (1.4-fold) organic matter degradation rates, as well as threefold higher methane production compared to the non-heated control. Despite the significant enhancements in performance resulting from supplemental heat addition, heated leachate recirculation did not significantly impact waste temperatures, and the effects were mainly restricted to short periods after recirculation and mostly at the upper layers of the waste. These findings suggest that improvements in bioreactor landfill performance may be achieved without increasing the temperature of the whole in-place waste, but rather more economically by raising the temperature at the leachate/waste interface which is also exposed to the maximum moisture levels within the waste matrix.

  13. Synergistic Enhancement of Cellobiohydrolase Performance on Pretreated Corn Stover by Addition of Xylanase and Esterase Activities

    SciTech Connect

    Selig, M. J.; Knoshaug E. P.; Adney, W. S.; Himmel, M. E.; Decker, S. R.

    2007-11-01

    Significant increases in the depolymerization of corn stover cellulose by cellobiohydrolase I (Cel7A) from Trichoderma reesei were observed using small quantities of non-cellulolytic cell wall-degrading enzymes. Purified endoxylanase (XynA), ferulic acid esterase (FaeA), and acetyl xylan esterase (Axe1) all enhanced Cel7A performance on corn stover subjected to hot water pretreatment. In all cases, the addition of these activities improved the effectiveness of the enzymatic hydrolysis in terms of the quantity of cellulose converted per milligram of total protein. Improvement in cellobiose release by the addition of the non-cellulolytic enzymes ranged from a 13-84% increase over Cel7A alone. The most effective combinations included the addition of both XynA and Axe1, which synergistically enhance xylan conversions resulting in additional synergistic improvements in glucan conversion. Additionally, we note a direct relationship between enzymatic xylan removal in the presence of XynA and the enhancement of cellulose hydrolysis by Cel7A.

  14. Effects of NaOH addition on performance of the direct hydrazine fuel cell

    NASA Astrophysics Data System (ADS)

    Yin, Wen Xia; Li, Zhou Peng; Zhu, Jing Ke; Qin, Hai Ying

    In this work, we suggested a figuration of the direct hydrazine fuel cell (DHFC) using non-precious metals as the anode catalyst, ion exchange membranes as the electrolyte and alkaline hydrazine solutions as the fuel. NaOH addition in the anolyte effectively improved the open circuit voltage and the performance of the DHFC. A power density of 84 mW cm -2 has been achieved when operating the cell at room temperature. It was found that the cell performance was mainly influenced by anode polarization when using alkaline N 2H 4 solutions with low NaOH concentrations. However, when using alkaline N 2H 4 solutions with high NaOH concentrations as the fuel, the cell performance was mainly influenced by cathode polarization.

  15. Validity of the Optometry Admission Test in Predicting Performance in Schools and Colleges of Optometry.

    ERIC Educational Resources Information Center

    Kramer, Gene A.; Johnston, JoElle

    1997-01-01

    A study examined the relationship between Optometry Admission Test scores and pre-optometry or undergraduate grade point average (GPA) with first and second year performance in optometry schools. The test's predictive validity was limited but significant, and comparable to those reported for other admission tests. In addition, the scores…

  16. Compositions, Functions, and Testing of Friction Brake Materials and Their Additives

    SciTech Connect

    Blau, PJ

    2001-10-22

    The purpose of this report is to present a survey of commercial brake materials and additives, and to indicate their typical properties and functions, especially as regards their use in heavy trucks. Most truck pad and shoe materials described here were designed to wear against cast iron. Brake material test methods are also briefly described. This report does not address issues associated with the fabrication and manufacturing of brake materials. Since there are literally thousands of brake material additives, and their combinations are nearly limitless, it is impractical to list them all here. Rather, an attempt has been made to capture the primary constituents and their functions. An Appendix contains thermo-physical properties of some current and potential brake materials.

  17. Diagnostic Performance Tests For Elementary Children (Grades 1-4).

    ERIC Educational Resources Information Center

    Hardin, Donald H.; Garcia, Mary Jane

    1982-01-01

    The basic skills of running, jumping, throwing, and ball handling are of primary importance in physical education programs. A battery of four tests and a chart of average performances are presented for testing elementary students. (CJ)

  18. Qualification Plus: Performance and Durability Tests Beyond IEC 61215 (Presentation)

    SciTech Connect

    Kurtz, S.; Jordan, J.; Kempe, M.; Miller, D.; Bosco, N.; Silverman, T.; Hacke, P.; Phillips, N.; Earnest, T.; Romero, R.

    2014-03-01

    Qualification Plus is an accelerated test protocol and quality management system that gives higher confidence in field performance of PV modules compared with conventional qualification testing. The test sequences are being developed as consensus standards, but the early publication of these tests enables the community to begin benefiting from them sooner.

  19. AiResearch QCGAT engine performance and emissions tests

    NASA Technical Reports Server (NTRS)

    Norgren, W. M.

    1980-01-01

    Results of aerodynamic performance and emission tests, conducted on a specially designed QCGAT engine in the 17,793-N (4,000 lb) thrust class, are presented. Performance of the AiResearch QCGAT engine was excellent throughout all testing. No serious mechanical malfunctions were encountered, and no significant test time was lost due to engine-related problems. Emissions were drastically reduced over similar engines, and the engine exhibited good smoke performance.

  20. Motivational and Cognitive Test-Taking Strategies and Their Influence on Test Performance in Mathematics

    ERIC Educational Resources Information Center

    Peng, Yun; Hong, Eunsook; Mason, Elsa

    2014-01-01

    A structural equation model of relationships among testing-related motivation variables (test value, effort, self-efficacy, and test anxiety), test-taking strategies (test tactics and metacognitive strategies), gender, and math test performance were examined with a sample of 10th graders (N = 438; 182 males and 256 females). In general, motivation…

  1. Design, Development and Hotfire Testing of Monolithic Copper and Bimetallic Additively Manufactured Combustion Chambers

    NASA Technical Reports Server (NTRS)

    Gradl, Paul; Barnett, Greg; Brandsmeier, Will; Greene, Sandy Elam; Protz, Chris

    2016-01-01

    NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM) otherwise commonly referred to as additive manufacturing. The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for the GRCop-84 copper-alloy commensurate with powder bed additive manufacturing, evaluate bimetallic deposition and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. As a direct spin off of this program, NASA is working with industry partners to further develop the printing process for the GRCop-84 material in addition to the C-18150 (CuCrZr) material. To advance the process further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic additively manufactured chambers. A 1.2k sized thrust-chamber was designed and developed to compare the printing process of the GRCop-84 and C-18150 SLM materials. A series of similar MCC liners also completed development with an Inconel 625 jacket bonded to the GRcop-84 liner evaluating direct metal deposition (DMD) laser and arc-based techniques. This paper describes the design, development, manufacturing and testing of these combustion chambers and associated lessons learned throughout the design and development process.

  2. A review of cryogenic testing performed by the thermochemical test branch, Manned Spacecraft Center in support of Apollo 13 and14

    NASA Technical Reports Server (NTRS)

    Propp, C. E.; Mcgee, J. M.

    1971-01-01

    The Apollo 13 anomaly provided considerable impetus for a variety of types of cryogenic and ignition tests. The logic of the various test program designs, the test techniques, and their final impact upon the investigation findings are described. In addition, several test programs initiated to determine the thermal performance and general performance characteristics of the redesigned Apollo 14 cryogenic storage system are presented.

  3. Performance Testing of a Trace Contaminant Control Subassembly for the International Space Station

    NASA Technical Reports Server (NTRS)

    Perry, J. L.; Curtis, R. E.; Alexandre, K. L.; Ruggiero, L. L.; Shtessel, N.

    1998-01-01

    As part of the International Space Station (ISS) Trace Contaminant Control Subassembly (TCCS) development, a performance test has been conducted to provide reference data for flight verification analyses. This test, which used the U.S. Habitation Module (U.S. Hab) TCCS as the test article, was designed to add to the existing database on TCCS performance. Included in this database are results obtained during ISS development testing; testing of functionally similar TCCS prototype units; and bench scale testing of activated charcoal, oxidation catalyst, and granular lithium hydroxide (LiOH). The present database has served as the basis for the development and validation of a computerized TCCS process simulation model. This model serves as the primary means for verifying the ISS TCCS performance. In order to mitigate risk associated with this verification approach, the U.S. Hab TCCS performance test provides an additional set of data which serve to anchor both the process model and previously-obtained development test data to flight hardware performance. The following discussion provides relevant background followed by a summary of the test hardware, objectives, requirements, and facilities. Facility and test article performance during the test is summarized, test results are presented, and the TCCS's performance relative to past test experience is discussed. Performance predictions made with the TCCS process model are compared with the U.S. Hab TCCS test results to demonstrate its validation.

  4. Application and testing of additive manufacturing for mirrors and precision structures

    NASA Astrophysics Data System (ADS)

    Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

    2015-09-01

    Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

  5. Improvement of capacitive performances of symmetric carbon/carbon supercapacitors by addition of nanostructured polypyrrole powder

    NASA Astrophysics Data System (ADS)

    Benhaddad, L.; Gamby, J.; Makhloufi, L.; Pailleret, A.; Pillier, F.; Takenouti, H.

    2016-03-01

    A nanostructured polypyrrole powder was synthesized in a previous work from the oxidation of pyrrole by a nanostructured MnO2 powder used simultaneously as an oxidizing agent and a sacrificial template in a redox heterogeneous mechanism. In this study, this original PPy powder was used as an active additive material with different ratio in carbon/carbon symmetrical supercapacitors whose performances were studied by cyclic voltammetry and electrochemical impedance spectroscopy (EIS) using a Swagelok-type cell. From the EIS spectra, the complex capacitance was extracted using a model involving two Cole-Cole type complex capacitances linked in series. The specific capacitance values evaluated by EIS and cyclic voltammetry are in a good agreement between them. The results show that the addition of nanostructured polypyrrole powder improves significantly the specific capacitance of the carbon electrode and consequently the performances of carbon/carbon supercapacitors. The original and versatile synthesis method used to produce this polypyrrole powder appears to be attractive for large scale production of promising additives for electrode materials of supercapacitors.

  6. Priming competence diminishes the link between cognitive test anxiety and test performance. Implications for the interpretation of test scores.

    PubMed

    Lang, Jonas W B; Lang, Jessica

    2010-06-01

    Researchers disagree whether the correlation between cognitive test anxiety and test performance is causal or explainable by skill deficits, which lead to both cognitive test anxiety and lower test performance. Most causal theories of test anxiety assume that individual differences in cognitive test anxiety originate from differences in self-perceived competence. Accordingly, in the present research, we sought to temporarily heighten perceptions of competence using a priming intervention. Two studies with secondary- and vocational-school students (Ns = 219 and 232, respectively) contrasted this intervention with a no-priming control condition. Priming competence diminished the association between cognitive test anxiety and test performance by heightening the performance of cognitively test-anxious students and by lowering the performance of students with low levels of cognitive test anxiety. The findings suggest that cognitively test-anxious persons have greater abilities than they commonly show. Competency priming may offer a way to improve the situation of people with cognitive test anxiety.

  7. Advancement of flash hydrogasification: Task VIII. Performance testing

    SciTech Connect

    Falk, A.Y.; Schuman, M.D.; Kahn, D.R.

    1986-06-01

    This topical report documents the technical effort required to investigate and verify the reaction chemistry associated with the Rockwell Advanced Flash Hydropyrolysis (AFHP) concept for the production of substitute natural gas (SNG) from coal. The testing phase of the program included 5 preburner performance evaluation tests (14 test conditions) and 11 coal-fed reactor tests (19 test conditions). The reactor test parameters investigated spanned exist temperatures from 1775 to 2050/sup 0/F, residence times from 2 to 8 s, inlet gas-to-coal ratios from 0.15 to 0.27 lb-mole/lb, and inlet-steam-to-H/sub 2/ mole ratios from 0.15 to 0.86. One test was conducted to investigate the effect of CH/sub 4/ addition to the hydrogen feed stream (22 mole % CH/sub 4/), with subsequent partial oxidation of the CH/sub 4/ to CO/sub x/ in the preburner system, on the AFHP reactor chemistry and product gas composition. Overall carbon conversion and total carbon conversion to gases (namely, CH/sub 4/, C/sub 2/H/sub 6/, CO, and CO/sub 2/) ranged from 53 to 68% and 35 to 68%, respectively. The gas produced was primarily CH/sub 4/ (31 to 53% carbon conversion to CH/sub 4/). Carbon conversion to total liquids was strongly dependent on reactor exit temperature and to a lesser extent on residence time, with values ranging from about 20% to 1775/sup 0/F and 2-S residence time to zero at 1975/sup 0/F and residence times greater than 5 s. Carbon conversion to C/sub 6/H/sub 6/ asd high as 11.2% was obtained. Carbon conversion to CO/sub x/ ranged from 3.5 to 29.4%. Methane addition was found not to significantly affect the AFHP reactor chemistry. As a result of this program, Rockwell has expanded its data base and significantly improved its correlation model describing the processes occurring during flash hydropyrolysis. The correlation provides an excellent tool for subsequent process evaluations to determine the economic potential of the Rockwell coal hydrogasification process. 23 refs., 51 figs

  8. Fenestration System Performance Research, Testing, and Evaluation

    SciTech Connect

    Jim Benney

    2009-11-30

    The US DOE was and is instrumental to NFRC's beginning and its continued success. The 2005 to 2009 funding enables NFRC to continue expanding and create new, improved ratings procedures. Research funded by the US DOE enables increased fenestration energy rating accuracy. International harmonization efforts supported by the US DOE allow the US to be the global leader in fenestration energy ratings. Many other governments are working with the NFRC to share its experience and knowledge toward development of their own national fenestration rating process similar to the NFRC's. The broad and diverse membership composition of NFRC allows anyone with a fenestration interest to come forward with an idea or improvement to the entire fenestration community for consideration. The NFRC looks forward to the next several years of growth while remaining the nation's resource for fair, accurate, and credible fenestration product energy ratings. NFRC continues to improve its rating system by considering new research, methodologies, and expanding to include new fenestration products. Currently, NFRC is working towards attachment energy ratings. Attachments are blinds, shades, awnings, and overhangs. Attachments may enable a building to achieve significant energy savings. An NFRC rating will enable fair competition, a basis for code references, and a new ENERGY STAR product category. NFRC also is developing rating methods to consider non specular glazing such as fritted glass. Commercial applications frequently use fritted glazing, but no rating method exists. NFRC is testing new software that may enable this new rating and contribute further to energy conservation. Around the world, many nations are seeking new energy conservation methods and NFRC is poised to harmonize its rating system assisting these nations to better manage and conserve energy in buildings by using NFRC rated and labeled fenestration products. As this report has shown, much more work needs to be done to

  9. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    PubMed Central

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-01-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator. PMID:27509823

  10. Loophole-free Bell test using electron spins in diamond: second experiment and additional analysis

    NASA Astrophysics Data System (ADS)

    Hensen, B.; Kalb, N.; Blok, M. S.; Dréau, A. E.; Reiserer, A.; Vermeulen, R. F. L.; Schouten, R. N.; Markham, M.; Twitchen, D. J.; Goodenough, K.; Elkouss, D.; Wehner, S.; Taminiau, T. H.; Hanson, R.

    2016-08-01

    The recently reported violation of a Bell inequality using entangled electronic spins in diamonds (Hensen et al., Nature 526, 682–686) provided the first loophole-free evidence against local-realist theories of nature. Here we report on data from a second Bell experiment using the same experimental setup with minor modifications. We find a violation of the CHSH-Bell inequality of 2.35 ± 0.18, in agreement with the first run, yielding an overall value of S = 2.38 ± 0.14. We calculate the resulting P-values of the second experiment and of the combined Bell tests. We provide an additional analysis of the distribution of settings choices recorded during the two tests, finding that the observed distributions are consistent with uniform settings for both tests. Finally, we analytically study the effect of particular models of random number generator (RNG) imperfection on our hypothesis test. We find that the winning probability per trial in the CHSH game can be bounded knowing only the mean of the RNG bias. This implies that our experimental result is robust for any model underlying the estimated average RNG bias, for random bits produced up to 690 ns too early by the random number generator.

  11. Relationships of Cognitive Components of Test Anxiety to Test Performance: Implications for Assessment and Treatment.

    ERIC Educational Resources Information Center

    Bruch, Monroe A.; And Others

    1983-01-01

    Assessed the degree to which components of test-taking strategies, covert self-statements, and subjective anxiety during an exam provide increments in prediction of test performance of undergraduates (N=72). Results showed that only test-taking strategies provided a significant increment to multiple-choice and essay test performance but not math…

  12. Comparing the Effects of Test Anxiety on Independent and Integrated Speaking Test Performance

    ERIC Educational Resources Information Center

    Huang, Heng-Tsung Danny; Hung, Shao-Ting Alan

    2013-01-01

    Integrated speaking test tasks (integrated tasks) offer textual and/or aural input for test takers on which to base their subsequent oral responses. This path-analytic study modeled the relationship between test anxiety and the performance of such tasks and explored whether test anxiety would differentially affect the performance of independent…

  13. Development of a test protocol for evaluating EVA glove performance

    NASA Technical Reports Server (NTRS)

    Hinman, Elaine M.

    1992-01-01

    Testing gloved hand performance involves work from several disciplines. Evaluations performed in the course of reenabling a disabled hand, designing a robotic end effector or master controller, or hard-suit design have all yielded relevant information, and, in most cases, produced performance test methods. Most times, these test methods have been primarily oriented toward their parent discipline. For space operations, a comparative test which would provide a way to quantify pressure glove and end effector performance would be useful in dividing tasks between humans and robots. Such a test would have to rely heavily on sensored measurement, as opposed to questionnaires, to produce relevant data. However, at some point human preference would have to be taken into account. This paper presents a methodology for evaluating gloved hand performance which attempts to respond to these issues. Glove testing of a prototype glove design using this method is described.

  14. Enhanced performance of polymer:fullerene bulk heterojunction solar cells upon graphene addition

    SciTech Connect

    Robaeys, Pieter Dierckx, Wouter; Dexters, Wim; Spoltore, Donato; Drijkoningen, Jeroen; Bonaccorso, Francesco; Bourgeois, Emilie; D'Haen, Jan; Haenen, Ken; Manca, Jean V.; Nesladek, Milos; Liesenborgs, Jori; Van Reeth, Frank; Lombardo, Antonio; Ferrari, Andrea C.

    2014-08-25

    Graphene has potential for applications in solar cells. We show that the short circuit current density of P3HT (Poly(3-hexylthiophene-2,5-diyl):PCBM((6,6)-Phenyl C61 butyric acid methyl ester) solar cells is enhanced by 10% upon the addition of graphene, with a 15% increase in the photon to electric conversion efficiency. We discuss the performance enhancement by studying the crystallization of P3HT, as well as the electrical transport properties. We show that graphene improves the balance between electron and hole mobilities with respect to a standard P3HT:PCBM solar cell.

  15. Greek research reactor performance characteristics after addition of beryllium reflector and LEU fuel

    SciTech Connect

    Deen, J.R.; Snelgrove, J.L.; Papastergiou, C.

    1992-12-31

    The GRR-1 is a 5-MW pool-type, light-water-moderated and-cooled reactor fueled with MTR-type fuel elements. Recently received Be reflector blocks will soon be added to the core to add additional reactivity until fresh LEU fuel arrives. REBUS-3 xy fuel cycle analyses, using burnup dependent cross sections, were performed to assist in fuel management decisions for the water- and Be-reflected HEU nonequilibrium cores. Cross sections generated by EPRI-CELL have been benchmarked to identical VIM Monte Carlo models. The size of the Be-reflected LEU core has been reduced to 30 elements compared to 35 for the HEU water-reflected core, and an equilibrium cycle calculation has been performed.

  16. Greek research reactor performance characteristics after addition of beryllium reflector and LEU fuel

    SciTech Connect

    Deen, J.R.; Snelgrove, J.L. ); Papastergiou, C. )

    1992-01-01

    The GRR-1 is a 5-MW pool-type, light-water-moderated and-cooled reactor fueled with MTR-type fuel elements. Recently received Be reflector blocks will soon be added to the core to add additional reactivity until fresh LEU fuel arrives. REBUS-3 xy fuel cycle analyses, using burnup dependent cross sections, were performed to assist in fuel management decisions for the water- and Be-reflected HEU nonequilibrium cores. Cross sections generated by EPRI-CELL have been benchmarked to identical VIM Monte Carlo models. The size of the Be-reflected LEU core has been reduced to 30 elements compared to 35 for the HEU water-reflected core, and an equilibrium cycle calculation has been performed.

  17. Performance testing and analysis of vertical ambient air vaporizers

    NASA Astrophysics Data System (ADS)

    Pandey, A. S.; Singh, V. N.; Shah, M. I.; Acharya, D. V.

    2017-02-01

    Ambient air vaporizers are used to regasify cryogenic liquids at extremely low temperature (below -153°C). Frost formation occurs on it due to large temperature difference between ambient air and cryogenic fluid. Frosting induces additional load on equipment and reduces its heat transfer effectiveness. Hence, mechanical and thermal design of vaporizers account for frosting. An experimental set-up has been designed and effects of flow rate and ground clearance on the performance of ambient air vaporizers are evaluated. The flow rate is increased from the rated capacity of 500 Nm3/h to 640 Nm3/h and ground clearance is reduced from 500 mm to 175 mm. The above variations reduce the time duration for which gaseous nitrogen is delivered at temperature higher than 10.1°C (desired). Hence duty cycle reduces from eight hours to five hours. The other factors affecting performance such as fin configuration, fluid type, fluid pressure, intermittent flow nature and climatic conditions are assumed to be constant over the test duration. The decrement in outlet gas temperature (from 38 °C to 10.1°C) with corresponding increment in frost thickness leads to deterioration of performance of ambient air vaporizers.

  18. Electronics Manufacturer Provided With Testing and Evaluation Data Necessary to Obtain Additional Orders

    NASA Technical Reports Server (NTRS)

    1998-01-01

    A local electronics manufacturer, the Sterling Manufacturing Company, was presented with the opportunity to supply 30,000 automotive cellular antennas to a European subsidiary of a large U.S. auto manufacturer. Although the company built an antenna that they believed would meet the auto manufacturer's specifications, they were unable to conduct the necessary validation tests in-house. They decided to work with NASA Lewis Research Center's Space Electronics Division, which, as part of its technology development program, evaluates the performance of antennas in its Microwave Systems Lab to assess their capabilities for space communications applications. Data measured in Lewis' Microwave Systems Lab proved that Sterling's antenna performed better than specified by the auto manufacturer.

  19. A Method to Evaluate Additional Waste Forms to Optimize Performance of the HLW Repository

    SciTech Connect

    D. Gombert; L. Lauerhass

    2006-02-01

    The DOE high-level waste (HLW) disposal system is based on decisions made in the 1970s. The de facto Yucca Mountain WAC for HLW, contained in the Waste Acceptance System Requirements Document (WASRD), and the DOE-EM Waste Acceptance Product Specification for Vitrified High Level Waste Forms (WAPS) tentatively describes waste forms to be interred in the repository, and limits them to borosilicate glass (BSG). It is known that many developed waste forms are as durable as or better than environmental assessment or “EA”-glass. Among them are the salt-ceramic and metallic waste forms developed at ANL-W. Also, iron phosphate glasses developed at University of Missouri show promise in stabilizing the most refractory materials in Hanford HLW. However, for any of this science to contribute, the current Total System Performance Assessment model must be able to evaluate the additional waste form to determine potential impacts on repository performance. The results can then support the technical bases required in the repository license application. A methodology is proposed to use existing analysis models to evaluate potential additional waste forms for disposal without gathering costly material specific degradation data. The concept is to analyze the potential impacts of waste form chemical makeup on repository performance assuming instantaneous waste matrix dissolution. This assumption obviates the need for material specific degradation models and is based on the relatively modest fractional contribution DOE HLW makes to the repository radionuclide and hazardous metals inventory. The existing analysis models, with appropriate data modifications, are used to evaluate geochemical interactions and material transport through the repository. This methodology would support early screening of proposed waste forms through simplified evaluation of disposal performance, and would provide preliminary guidance for repository license amendment in the future.

  20. A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

    NASA Technical Reports Server (NTRS)

    Grady, Joseph E.; Haller, William J.; Poinsatte, Philip E.; Halbig, Michael C.; Schnulo, Sydney L.; Singh, Mrityunjay; Weir, Don; Wali, Natalie; Vinup, Michael; Jones, Michael G.; Patterson, Clark; Santelle, Tom; Mehl, Jeremy

    2015-01-01

    The research and development activities reported in this publication were carried out under NASA Aeronautics Research Institute (NARI) funded project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing." The objective of the project was to conduct evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. The results of the activities are described in three part report. The first part of the report contains the data and analysis of engine system trade studies, which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. The technical scope of activities included an assessment of the feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composites, which were accomplished by fabricating prototype engine components and testing them in simulated engine operating conditions. The manufacturing process parameters were developed and optimized for polymer and ceramic composites (described in detail in the second and third part of the report). A number of prototype components (inlet guide vane (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included turbine nozzle components. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

  1. Writing about testing worries boosts exam performance in the classroom.

    PubMed

    Ramirez, Gerardo; Beilock, Sian L

    2011-01-14

    Two laboratory and two randomized field experiments tested a psychological intervention designed to improve students' scores on high-stakes exams and to increase our understanding of why pressure-filled exam situations undermine some students' performance. We expected that sitting for an important exam leads to worries about the situation and its consequences that undermine test performance. We tested whether having students write down their thoughts about an upcoming test could improve test performance. The intervention, a brief expressive writing assignment that occurred immediately before taking an important test, significantly improved students' exam scores, especially for students habitually anxious about test taking. Simply writing about one's worries before a high-stakes exam can boost test scores.

  2. 46 CFR 160.151-29 - Additional approval tests for SOLAS A and SOLAS B inflatable liferafts.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 6 2014-10-01 2014-10-01 false Additional approval tests for SOLAS A and SOLAS B... Inflatable Liferafts (SOLAS) § 160.151-29 Additional approval tests for SOLAS A and SOLAS B inflatable...), Chapter IV/4.3.5 (incorporated by reference, see § 160.151-5 of this subpart), the following test must...

  3. 46 CFR 160.151-29 - Additional approval tests for SOLAS A and SOLAS B inflatable liferafts.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 6 2013-10-01 2013-10-01 false Additional approval tests for SOLAS A and SOLAS B... Inflatable Liferafts (SOLAS) § 160.151-29 Additional approval tests for SOLAS A and SOLAS B inflatable...), Chapter IV/4.3.5 (incorporated by reference, see § 160.151-5 of this subpart), the following test must...

  4. Development of performance tests for an automated MC and A system

    SciTech Connect

    Kok, K.D.; Klingensmith, R.W.; Riffle, W.; Carver, R.D.; Schumacher, S.S.; Lavender, J.C.; Smith, B.W.

    1988-01-01

    Performance tests of MC and A systems using computers are described, and some example scenarios are discussed. Facility personnel or an external inspection group may use performance tests to evaluate MC and A capabilities under actual operating conditions. This paper addresses test elements common to both user groups. Performance tests consist of scenario development, security, and safety measures, conduct, and evaluation. Because exercises often test scenarios against which the MC and A system is protecting, they may require additional security and safety measures. Computer systems enhance MC and A by providing greater speed, increased precision, and automated checks. Performance tests for MC and A systems using computers differ from performance tests employing manual data systems in that the scenarios must anticipate computer actions rather than utilize controllers to adjust the scenario.

  5. Development of performance tests for an automated MC and A system

    SciTech Connect

    Kok, K.D.; Klingensmith, R.W.; Riffle, W.; Carver, R.D.; Schumacher, S.S.; Byers, K.R.; Lavender, J.C.; Smith, B.W.

    1988-05-19

    Performance tests of MCandA systems using computers are described, and some example scenarios are discussed. Facility personnel or an external inspection group may use performance tests to evaluate MCandA Capabilities under actual operating conditions. This paper addresses test elements common to both user groups. Performance tests consist of scenario development, security and safety measures, conduct, and evaluation. Because exercises often test scenarios against which the MCandA system is protecting, they may require additional security and safety measures. Computer systems enhance MCandA by providing greater speed, increased precision, and automated checks. performance tests for MCandA systems using computers differ from performance tests employing manual data systems in that the scenarios must anticipate computer actions rather than utilize controllers to adjust the scenario.

  6. THE RELATIONSHIP BETWEEN TRUNK ENDURANCE PLANK TESTS AND ATHLETIC PERFORMANCE TESTS IN ADOLESCENT SOCCER PLAYERS

    PubMed Central

    Kaneoka, Koji

    2016-01-01

    Background Although it is believed that trunk function is important for athletic performance, few researchers have demonstrated a significant relationship between the trunk function and athletic performance. Recently, the prone plank and side plank tests have been used to assess trunk function. Purpose The purpose of this study was to investigate the relationships between trunk endurance plank tests and athletic performance tests, including whether there is a relationship between long distance running and trunk endurance plank tests in adolescent male soccer players. Study design Cross sectional study design. Methods Fifty-five adolescent male soccer players performed prone and side plank tests and seven performance tests: the Cooper test, the Yo-Yo intermittent recovery test, the step 50 agility test, a 30-m sprint test, a vertical countermovement jump, a standing five-step jump, and a rebound jump. The relationships between each individual plank test, the combined score of both plank tests, and performance tests were analyzed using the Pearson correlation coefficient. Results The combined score of plank tests was highly correlated with the Yo-Yo intermittent recovery test (r = 0.710, p < 0.001), and was moderately correlated with the Cooper test (r = 0.567, p < 0.001). Poor correlation was observed between the prone plank test and step 50 agility test (r = -0.436, p = 0.001) and no significant correlations were observed between plank tests and jump performance tests. Conclusions The results suggest that trunk endurance plank tests are positively correlated with the Yo-Yo intermittent recovery test, the Cooper test, and the step 50 agility test. Level of Evidence Level 2 PMID:27757284

  7. Testing departure from additivity in Tukey's model using shrinkage: application to a longitudinal setting.

    PubMed

    Ko, Yi-An; Mukherjee, Bhramar; Smith, Jennifer A; Park, Sung Kyun; Kardia, Sharon L R; Allison, Matthew A; Vokonas, Pantel S; Chen, Jinbo; Diez-Roux, Ana V

    2014-12-20

    While there has been extensive research developing gene-environment interaction (GEI) methods in case-control studies, little attention has been given to sparse and efficient modeling of GEI in longitudinal studies. In a two-way table for GEI with rows and columns as categorical variables, a conventional saturated interaction model involves estimation of a specific parameter for each cell, with constraints ensuring identifiability. The estimates are unbiased but are potentially inefficient because the number of parameters to be estimated can grow quickly with increasing categories of row/column factors. On the other hand, Tukey's one-degree-of-freedom model for non-additivity treats the interaction term as a scaled product of row and column main effects. Because of the parsimonious form of interaction, the interaction estimate leads to enhanced efficiency, and the corresponding test could lead to increased power. Unfortunately, Tukey's model gives biased estimates and low power if the model is misspecified. When screening multiple GEIs where each genetic and environmental marker may exhibit a distinct interaction pattern, a robust estimator for interaction is important for GEI detection. We propose a shrinkage estimator for interaction effects that combines estimates from both Tukey's and saturated interaction models and use the corresponding Wald test for testing interaction in a longitudinal setting. The proposed estimator is robust to misspecification of interaction structure. We illustrate the proposed methods using two longitudinal studies-the Normative Aging Study and the Multi-ethnic Study of Atherosclerosis.

  8. Testing Departure from Additivity in Tukey’s Model using Shrinkage: Application to a Longitudinal Setting

    PubMed Central

    Ko, Yi-An; Mukherjee, Bhramar; Smith, Jennifer A.; Park, Sung Kyun; Kardia, Sharon L.R.; Allison, Matthew A.; Vokonas, Pantel S.; Chen, Jinbo; Diez-Roux, Ana V.

    2014-01-01

    While there has been extensive research developing gene-environment interaction (GEI) methods in case-control studies, little attention has been given to sparse and efficient modeling of GEI in longitudinal studies. In a two-way table for GEI with rows and columns as categorical variables, a conventional saturated interaction model involves estimation of a specific parameter for each cell, with constraints ensuring identifiability. The estimates are unbiased but are potentially inefficient because the number of parameters to be estimated can grow quickly with increasing categories of row/column factors. On the other hand, Tukey’s one degree of freedom (df) model for non-additivity treats the interaction term as a scaled product of row and column main effects. Due to the parsimonious form of interaction, the interaction estimate leads to enhanced efficiency and the corresponding test could lead to increased power. Unfortunately, Tukey’s model gives biased estimates and low power if the model is misspecified. When screening multiple GEIs where each genetic and environmental marker may exhibit a distinct interaction pattern, a robust estimator for interaction is important for GEI detection. We propose a shrinkage estimator for interaction effects that combines estimates from both Tukey’s and saturated interaction models and use the corresponding Wald test for testing interaction in a longitudinal setting. The proposed estimator is robust to misspecification of interaction structure. We illustrate the proposed methods using two longitudinal studies — the Normative Aging Study and the Multi-Ethnic Study of Atherosclerosis. PMID:25112650

  9. Effect of additives on the tensile performance and protein solubility of industrial oilseed residual based plastics.

    PubMed

    Newson, William R; Kuktaite, Ramune; Hedenqvist, Mikael S; Gällstedt, Mikael; Johansson, Eva

    2014-07-16

    Ten chemical additives were selected from the literature for their proposed modifying activity in protein-protein interactions. These consisted of acids, bases, reducing agents, and denaturants and were added to residual deoiled meals of Crambe abyssinica (crambe) and Brassica carinata (carinata) to modify the properties of plastics produced through hot compression molding at 130 °C. The films produced were examined for tensile properties, protein solubility, molecular weight distribution, and water absorption. Of the additives tested, NaOH had the greatest positive effect on tensile properties, with increases of 105% in maximum stress and 200% in strain at maximum stress for crambe and a 70% increase in strain at maximum stress for carinata. Stiffness was not increased by any of the applied additives. Changes in tensile strength and elongation for crambe and elongation for carinata were related to changes in protein solubility. Increased pH was the most successful in improving the protein aggregation and mechanical properties within the complex chemistry of residual oilseed meals.

  10. New approaches to performance testing of improved cookstoves.

    PubMed

    Johnson, Michael; Edwards, Rufus; Berrueta, Victor; Masera, Omar

    2010-01-01

    Monitoring and evaluation of improved cookstove performance is a critical factor in program success; however, consistent evidence indicates water boiling tests and controlled cooking tests are not representative of stove performance during daily cooking activities, and there is no ability to link these tests to kitchen performance tests during normal daily cooking activities. Since emissions from cookstoves contribute heavily to regional estimates of carbonaceous aerosols and other short-lived greenhouse species and given the current importance of stove performance tests as a basis for global climate prediction models and IPCC inventories, improvements in performance testing are critical to derive more representative estimates. Here real-time combustion efficiencies and emissions rates from daily burn cycles of open fires and improved stoves in Mexico are used to propose a new approach to stove performance testing, using simple and economical measurement methods, based on replication of the distribution of emission rates and combustion efficiencies seen during daily cooking activities in homes. This approach provides more relevant information for global climate models and inventories, while also providing a means to recreate representative emissions profiles in a laboratory setting for technical analyses. On the basis of emission rates and combustion efficiencies during normal daily cooking, we suggest performance criteria that can be used as benchmarks for laboratory testing of improved stoves in the absence of site-specific information, although requiring confirmation by field testing during daily cooking activities.

  11. 40 CFR 63.563 - Compliance and performance testing.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (4), or (d)(2). (3) Operation and maintenance inspections. If the 3-hour or 3-cycle block average... flare, as determined in § 63.564(f). (6) Carbon adsorber. During the initial performance test required... section shall conduct a performance test once each year. (i) Compliance determination for carbon...

  12. 10 CFR 26.168 - Blind performance testing.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Laboratories Certified by the Department of Health... blind performance test samples to the HHS-certified laboratory. (1) During the initial 90-day period of... licensee or other entity shall submit blind performance test samples to each HHS-certified laboratory...

  13. 40 CFR 63.805 - Performance test methods.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 11 2013-07-01 2013-07-01 false Performance test methods. 63.805 Section 63.805 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Wood Furniture Manufacturing Operations § 63.805 Performance test...

  14. 40 CFR 63.805 - Performance test methods.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 11 2012-07-01 2012-07-01 false Performance test methods. 63.805 Section 63.805 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Wood Furniture Manufacturing Operations § 63.805 Performance test...

  15. 40 CFR 63.805 - Performance test methods.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 10 2011-07-01 2011-07-01 false Performance test methods. 63.805 Section 63.805 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS...) National Emission Standards for Wood Furniture Manufacturing Operations § 63.805 Performance test...

  16. 40 CFR 63.606 - Performance tests and compliance provisions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., phosphate rock dryer, and phosphate rock calciner. The owner or operator shall conduct the performance test... phosphate rock calciner. The owner or operator shall conduct the performance test according to the... or operator of a new or existing phosphate rock calciner shall demonstrate compliance with...

  17. 40 CFR 63.606 - Performance tests and compliance provisions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., phosphate rock dryer, and phosphate rock calciner. The owner or operator shall conduct the performance test... phosphate rock calciner. The owner or operator shall conduct the performance test according to the... or operator of a new or existing phosphate rock calciner shall demonstrate compliance with...

  18. 40 CFR 63.606 - Performance tests and compliance provisions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., phosphate rock dryer, and phosphate rock calciner. The owner or operator shall conduct the performance test... phosphate rock calciner. The owner or operator shall conduct the performance test according to the... or operator of a new or existing phosphate rock calciner shall demonstrate compliance with...

  19. 40 CFR 63.606 - Performance tests and compliance provisions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., phosphate rock dryer, and phosphate rock calciner. The owner or operator shall conduct the performance test... phosphate rock calciner. The owner or operator shall conduct the performance test according to the... or operator of a new or existing phosphate rock calciner shall demonstrate compliance with...

  20. 40 CFR 63.606 - Performance tests and compliance provisions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., phosphate rock dryer, and phosphate rock calciner. The owner or operator shall conduct the performance test... phosphate rock calciner. The owner or operator shall conduct the performance test according to the... or operator of a new or existing phosphate rock calciner shall demonstrate compliance with...

  1. Results of Performance Tests Performed on the John Watts WW Casing Connection on 7" Pipe

    SciTech Connect

    John D. Watts

    2000-02-01

    applied to the connection by applying it to the box or pin only and reducing the amount applied. Samples 3 and 4 received one makeup only. Sample 5 initially received two make/breaks to test for galling resistance before final makeup, No galling was observed. Later, three additional make/breaks were performed with no pin end collapse and galling over 1/2 a thread occurring on one of the breakouts. During the make/break tests, the stabbing and hand tight makeup of the WW connection was found to be very easy and trouble free. There was no tendency to crossthread, even when stabbed at an angle, and it screwed together very smoothly up to hand tight. During power tight makeup, there was no heat generated in the box (as checked by hand contact) and no jerkiness associated with any of the makeups or breakouts. Sample 2 was tested in pure compression. The maximum load obtained was 1,051 kips and the connection was beginning to significantly deform as the sample buckled. Actual pipe yield was 1,226 kips. Sample 3 was capped-end pressure tested to failure. The capped-end yield pressure of the pipe was 16,572 psi and the sample began to leak at 12,000 psi. Sample 4 was tested in pure tension. The maximum load obtained was 978 kips and the connection failed by fracture at the pin critical section. Actual pipe yield was 1,226 kips. Sample 5 was tested in combined tension/compression and internal gas pressure. The sample was assembled, setup and tested four times. The first time was with a torque of 7,298 ft-lbs and the connection leaked halfway to ISO Load Point 2 with loads of 693 kips and 4,312 psi. The second time the torque was increased to 14,488 ft-lbs and a leak occurred at 849 kips and 9,400 psi, which was ISO Load Point 2. The third time the makeup torque was again increased, to 20,456 ft-lbs, and a leak occurred at 716 kips and 11,342 psi, ISO Load Point 4. The fourth test was with the same torque as before, 20,617 ft-lbs, and the connection successfully tested up to load

  2. Design and Preliminary Performance Testing of Electronegative Gas Plasma Thruster

    NASA Technical Reports Server (NTRS)

    Liu, Thomas M.; Schloeder, Natalie R.; Walker, Mitchell L. R.; Polzin, Kurt A.; Dankanich, John W.; Aanesland, Ane

    2014-01-01

    In classical gridded electrostatic ion thrusters, positively charged ions are generated from a plasma discharge of noble gas propellant and accelerated to provide thrust. To maintain overall charge balance on the propulsion system, a separate electron source is required to neutralize the ion beam as it exits the thruster. However, if high-electronegativity propellant gases (e.g., sulfur hexafluoride) are instead used, a plasma discharge can result consisting of both positively and negatively charged ions. Extracting such electronegative plasma species for thrust generation (e.g., with time-varying, bipolar ion optics) would eliminate the need for a separate neutralizer cathode subsystem. In addition for thrusters utilizing a RF plasma discharge, further simplification of the ion thruster power system may be possible by also using the RF power supply to bias the ion optics. Recently, the PEGASES (Plasma propulsion with Electronegative gases) thruster prototype successfully demonstrated proof-of-concept operations in alternatively accelerating positively and negatively charged ions from a RF discharge of a mixture of argon and sulfur hexafluoride.i In collaboration with NASA Marshall Space Flight Center (MSFC), the Georgia Institute of Technology High-Power Electric Propulsion Laboratory (HPEPL) is applying the lessons learned from PEGASES design and testing to develop a new thruster prototype. This prototype will incorporate design improvements and undergo gridless operational testing and diagnostics checkout at HPEPL in April 2014. Performance mapping with ion optics will be conducted at NASA MSFC starting in May 2014. The proposed paper discusses the design and preliminary performance testing of this electronegative gas plasma thruster prototype.

  3. The Effects of Various Conductive Additive and Polymeric Binder Contents on the Performance of a Lithium-ion Composite

    SciTech Connect

    Stevenson, Cynthia; Liu, G.; Zheng, H.; Kim, S.; Deng, Y.; Minor, A.M.; Song, X.; Battaglia, V.S.

    2008-08-07

    Fundamental electrochemical methods, cell performance tests, and physical characterization tests such as electron microscopy were used to study the effects of levels of the inert materials (acetylene black (AB), a nano-conductive additive, and polyvinylidene difluoride (PVDF), a polymer binder) on the power performance of lithium-ion composite cathodes. The electronic conductivity of the AB/PVDF composites at different compositions was measured with a four-point probe direct current method. The electronic conductivity was found to increase rapidly and plateau at a AB:PVDF ratio 0.2:1 (by weight), with 0.8:1 being the highest conductivity composition. AB:PVDF compositions along the plateau of 0.2:1, 0.4:1, 0.6:1 and 0.8:1 were investigated. Electrodes of each of those compositions were fabricated with different fractions of AB/PVDF to active material. It was found that at the 0.8:1 AB:PVDF, the rate performance improved with increases in the AB/PVDF loading, whereas at the 0.2:1 AB:PVDF, the rate performance improved with decreases in the AB/PVDF loading. The impedance of electrodes made with 0.6:1 AB:PVDF was low and relatively invariant.

  4. Performance enhancement with powdered activated carbon (PAC) addition in a membrane bioreactor (MBR) treating distillery effluent.

    PubMed

    Satyawali, Yamini; Balakrishnan, Malini

    2009-10-15

    This work investigated the effect of powdered activated carbon (PAC) addition on the operation of a membrane bioreactor (MBR) treating sugarcane molasses based distillery wastewater (spentwash). The 8L reactor was equipped with a submerged 30 microm nylon mesh filter with 0.05 m(2) filtration area. Detailed characterization of the commercial wood charcoal based PAC was performed before using it in the MBR. The MBR was operated over 200 days at organic loading rates (OLRs) varying from 4.2 to 6.9 kg m(-3)d(-1). PAC addition controlled the reactor foaming during start up and enhanced the critical flux by around 23%; it also prolonged the duration between filter cleaning. Operation at higher loading rates was possible and for a given OLR, the chemical oxygen demand (COD) removal was higher with PAC addition. However, biodegradation in the reactor was limited and the high molecular weight compounds were not affected by PAC supplementation. The functional groups on PAC appear to interact with the polysaccharide portion of the sludge, which may reduce its propensity to interact with the nylon mesh.

  5. Performance testing of extremity dosimeters against a draft standard

    SciTech Connect

    Harty, R.; Reece, W.D.; Hooker, C.D.; McDonald, J.C.

    1990-09-01

    The assurance of worker radiation safety is directly related to the performance of personnel dosimetry. The US Department of Energy (DOE) has long recognized this critical relationship and has addressed this issue by instituting the DOE Laboratory Accreditation Program (DOELAP) which strives to improve the quality of personnel dosimetry through performance testing, dosimetry calibration, intercomparisons, evaluations and accreditations. One area of personnel dosimetry that has not been specifically addressed by DOELAP is extremity dosimeter testing. This task was directed at assessing the problems of implementing extremity dosimeter performance testing. A series of performance tests were made based on a draft standard written by the Health Physics Society Standards Committee (HPSSC) using extremity dosimeters currently in use at DOE and DOE contractor facilities. The results of this study indicate the need to incorporate performance testing of extremity dosimetry systems into DOELAP. Based on the results of this study, recommendations are made for improvements to the draft standard. 20 refs., 6 figs., 3 tabs.

  6. Assessment of production performance in 2 breeds of broilers fed prebiotics as feed additives.

    PubMed

    Hanning, I; Clement, A; Owens, C; Park, S H; Pendleton, S; Scott, E E; Almeida, G; Gonzalez Gil, F; Ricke, S C

    2012-12-01

    Pasture-flock-raised poultry are becoming an increasingly popular product, but only limited options are currently available for maintaining gut health. For these producers, prebiotics are an attractive option because they are generally recognized as safe (GRAS) and can be mixed into the feed and thus do not require adjustments to production protocols. However, if prebiotic treatments reduce production performance, they would not be useful to producers. Thus, the objective of this study was to measure performance of pasture-raised broilers fed 1 of 3 prebiotic treatments. For these trials, 2 breeds of birds were used: Naked Neck slow-growing breeds and Cornish White Rock cross fast-growing breeds. The experimental design was replicated for each breed. A total of 340 birds were split into 4 groups, each group fed one feed additive: 1) galactoligosaccharides (2% wt/wt), 2) fructooligosaccharides (1% wt/wt), 3) plum fibers (1% wt/wt), or 4) no additives. During the 8-wk rearing period, 10 birds from each group were collected and euthanized to take small intestine samples. Histological preparations were made from the small intestine tissue, and 4 measurements of villi height and crypt depth from each cross section were taken. Throughout the study, mortality was monitored and BW measurements were taken at 2-wk intervals. For the Cornish White Rock cross, the group receiving the feed supplemented with fructooligosaccharides had higher (P < 0.05) 8-wk BW than those fed Plum; control and birds fed galactoligosaccharides were intermediate. For the Naked Neck breed, the group receiving the plum fibers had the highest final BW. It appears that all 3 feed supplements offered some protective effect for alterations in villi length and crypt depth due to feed withdrawal, but only for the Naked Neck breed. The data indicate the 3 prebiotics utilized in this study could be used without risk of decreasing production performance, but only for Naked Neck breeds.

  7. Core-shell column Tanaka characterization and additional tests using active pharmaceutical ingredients.

    PubMed

    Ludvigsson, Jufang Wu; Karlsson, Anders; Kjellberg, Viktor

    2016-12-01

    In the last decade, core-shell particles have gained more and more attention in fast liquid chromatography separations due to their comparable performance with fully porous sub-2 μm particles and their significantly lower back pressure. Core-shell particles are made of a solid core surrounded by a shell of classic fully porous material. To embrace the developed core-shell column market and use these columns in pharmaceutical analytical applications, 17 core-shell C18 columns purchased from various vendors with various dimensions (50 mm × 2.1 mm to 100 mm × 3 mm) and particle sizes (1.6-2.7 μm) were characterized using Tanaka test protocols. Furthermore, four selected active pharmaceutical ingredients were chosen as test probes to investigate the batch to batch reproducibility for core-shell columns of particle size 2.6-2.7 μm, with dimension of 100 × 3 mm and columns of particle size 1.6 μm, with dimension 100 × 2.1 mm under isocratic elution. Columns of particle size 2.6-2.7 μm were also tested under gradient elution conditions. To confirm the claimed comparable efficiency of 2.6 μm core-shell particles as sub-2 μm fully porous particles, column performances of the selected core-shell columns were compared with BEH C18 , 1.7 μm, a fully porous column material as well.

  8. Item Response Theory Models for Performance Decline during Testing

    ERIC Educational Resources Information Center

    Jin, Kuan-Yu; Wang, Wen-Chung

    2014-01-01

    Sometimes, test-takers may not be able to attempt all items to the best of their ability (with full effort) due to personal factors (e.g., low motivation) or testing conditions (e.g., time limit), resulting in poor performances on certain items, especially those located toward the end of a test. Standard item response theory (IRT) models fail to…

  9. Timed Online Tests: Do Students Perform Better with More Time?

    ERIC Educational Resources Information Center

    Portolese, Laura; Krause, Jackie; Bonner, Julie

    2016-01-01

    This article focuses on timed tests and specifically on whether increased time enhances test performance. Three courses during the Winter 2015 term (quizzes n = 573) and three courses over the Spring 2015 term (quizzes n = 600) comprised this sample. Students were given the same tests, but the experimental group (Spring 2015) was given 50% more…

  10. The Relation of Task to Performance in Testing Verbs.

    ERIC Educational Resources Information Center

    Gradman, Harry L.; Hanania, Edith

    A study investigated the variability of language performance on different types of testing task, global versus discrete-focus. Three tests (cloze, multiple-choice, and fill-in-the-blank) were developed to measure learners' knowledge of five verb forms. The tests, containing corresponding items designed to elicit equivalent structures, were…

  11. Adolescents' Interest and Performances in Aerobic Fitness Testing

    ERIC Educational Resources Information Center

    Zhu, Xihe; Chen, Senlin; Parrott, James

    2014-01-01

    This study examined adolescents' interest in aerobic fitness testing and its relation to the test performances. Adolescents (N = 356) from three middle schools participated in the study. The participants took two aerobic fitness tests: the Progressive Aerobic Cardiovascular Endurance Run (PACER) and One-Mile Run (1MR) with a two-day interval, and…

  12. Tracking system performance tests in the MDS era

    NASA Technical Reports Server (NTRS)

    Buckles, B. J.

    1977-01-01

    Tracking system performance tests as developed to support DSN Mark III Data Subsystem implementation project and prepass readiness tests are described. The system test design, the rationale chosen for implementation, and the inevitable compromises imposed by schedule constraints and reserves are discussed.

  13. 40 CFR 60.56c - Compliance and performance testing.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... facility as defined in § 60.50c(a)(1) and (2), shall conduct an initial performance test as required under § 60.8 to determine compliance with the emissions limits using the procedures and test methods listed... test as required under § 60.8 to determine compliance with the emissions limits using the...

  14. Graphene oxide as a high-performance fluid-loss-control additive in water-based drilling fluids.

    PubMed

    Kosynkin, Dmitry V; Ceriotti, Gabriel; Wilson, Kurt C; Lomeda, Jay R; Scorsone, Jason T; Patel, Arvind D; Friedheim, James E; Tour, James M

    2012-01-01

    Graphene oxide (GO) performs well as a filtration additive in water-based drilling fluids at concentrations as low as 0.2 % (w/w) by carbon content. Standard American Petroleum Institute (API) filtration tests were conducted on pH-adjusted, aqueous dispersions of GO and xanthan gum. It was found that a combination of large-flake GO and powdered GO in a 3:1 ratio performed best in the API tests, allowing an average fluid loss of 6.1 mL over 30 min and leaving a filter cake ~20 μm thick. In comparison, a standard suspension (~12 g/L) of clays and polymers used in the oil industry gave an average fluid loss of 7.2 mL and a filter cake ~280 μm thick. Scanning electron microscopy imaging revealed the extreme pliability of well-exfoliated GO, as the pressure due to filtration crumpled single GO sheets, forcing them to slide through pores with diameters much smaller than the flake's flattened size. GO solutions also exhibited greater shear thinning and higher temperature stability compared to clay-based fluid-loss additives, demonstrating potential for high-temperature well applications.

  15. Web-Based Testing: Exploring the Relationship between Hardware Usability and Test Performance

    ERIC Educational Resources Information Center

    Huff, Kyle; Cline, Melinda; Guynes, Carl S.

    2012-01-01

    Web-based testing has recently become common in both academic and professional settings. A web-based test is administered through a web browser. Individuals may complete a web-based test at nearly any time and at any place. In addition, almost any computer lab can become a testing center. It is important to understand the environmental issues that…

  16. Relationships between driving simulator performance and driving test results.

    PubMed

    de Winter, J C F; de Groot, S; Mulder, M; Wieringa, P A; Dankelman, J; Mulder, J A

    2009-02-01

    This article is considered relevant because: 1) car driving is an everyday and safety-critical task; 2) simulators are used to an increasing extent for driver training (related topics: training, virtual reality, human-machine interaction); 3) the article addresses relationships between performance in the simulator and driving test results--a relevant topic for those involved in driver training and the virtual reality industries; 4) this article provides new insights about individual differences in young drivers' behaviour. Simulators are being used to an increasing extent for driver training, allowing for the possibility of collecting objective data on driver proficiency under standardised conditions. However, relatively little is known about how learner drivers' simulator measures relate to on-road driving. This study proposes a theoretical framework that quantifies driver proficiency in terms of speed of task execution, violations and errors. This study investigated the relationships between these three measures of learner drivers' (n=804) proficiency during initial simulation-based training and the result of the driving test on the road, occurring an average of 6 months later. A higher chance of passing the driving test the first time was associated with making fewer steering errors on the simulator and could be predicted in regression analysis with a correlation of 0.18. Additionally, in accordance with the theoretical framework, a shorter duration of on-road training corresponded with faster task execution, fewer violations and fewer steering errors (predictive correlation 0.45). It is recommended that researchers conduct more large-scale studies into the reliability and validity of simulator measures and on-road driving tests.

  17. Laboratory Performance Testing of Residential Window Air Conditioners

    SciTech Connect

    Winkler, J.; Booten, C.; Christensen, D.; Tomerlin, J.

    2013-03-01

    Window air conditioners are the dominant cooling product for residences, in terms of annual unit sales. They are inexpensive, portable and can be installed by the owner. For this reason, they are an attractive solution for supplemental cooling, for retrofitting air conditioning into a home which lacks ductwork, and for renters. Window air conditioners for sale in the United States are required to meet very modest minimum efficiency standards. Four window air conditioners' performance were tested in the Advanced HVAC Systems Laboratory on NREL's campus in Golden, CO. In order to separate and study the refrigerant system's performance, the unit's internal leakage pathways, the unit's fanforced ventilation, and the leakage around the unit resulting from installation in a window, a series of tests were devised that focused on each aspect of the unit's performance. These tests were designed to develop a detailed performance map to determine whole-house performance in different climates. Even though the test regimen deviated thoroughly from the industry-standard ratings test, the results permit simple calculation of an estimated rating for both capacity and efficiency that would result from a standard ratings test. Using this calculation method, it was found that the three new air conditioners' measured performance was consistent with their ratings. This method also permits calculation of equivalent SEER for the test articles. Performance datasets were developed across a broad range of indoor and outdoor operating conditions, and used them to generate performance maps.

  18. The Empirical Testing of a Musical Performance Assessment Paradigm

    ERIC Educational Resources Information Center

    Russell, Brian E.

    2010-01-01

    The purpose of this study was to test a hypothesized model of aurally perceived performer-controlled musical factors that influence assessments of performance quality. Previous research studies on musical performance constructs, musical achievement, musical expression, and scale construction were examined to identify the factors that influence…

  19. Some arguments in favor of a Myriophyllum aquaticum growth inhibition test in a water-sediment system as an additional test in risk assessment of herbicides.

    PubMed

    Tunić, Tanja; Knežević, Varja; Kerkez, Đurđa; Tubić, Aleksandra; Šunjka, Dragana; Lazić, Sanja; Brkić, Dragica; Teodorović, Ivana

    2015-09-01

    The present study compares the practicability, reproducibility, power, and sensitivity of a Myriophyllum aquaticum growth inhibition test in a water-sediment system with the recently accepted Myriophyllum spicatum test in an equivalent testing system and the standard Lemna sp. test. Special consideration was given to endpoints based on M. aquaticum control plant growth and variability of relative growth rate and yield: shoot length, fresh weight, dry weight, and root weight. Sensitivity analysis was based on tests performed with 3,5-dichlorophenol, atrazine, isoproturon, trifluralin, 2,4-dichlorophenoloxyacetic acid, and dicamba. Growth rates for average M. aquaticum control plants were 0.119 d(-1) and 0.112 d(-1), with average estimated doubling time 6.33 d and 6.74 d for relative growth rate fresh weight and shoot length, respectively. Intrinsic variability of M. aquaticum endpoints was low: 12.9%, 12.5%, and 17.8% for relative growth rate shoot length, relative growth rate fresh weight and yield fresh weight, respectively. The power of the test was fairly high. When the most sensitive endpoints were used for comparison, the 2 Myriophyllum species were similarly sensitive, more sensitive (in the case of auxin simulators), or at least equally sensitive as Lemna minor to other tested herbicides. The M. aquaticum 10-d test with a 7-d exposure period in a water-sediment system has acceptable sensitivity and can provide repeatable, reliable, and reproducible results; therefore, it should not be disregarded as a good and representative additional test in environmental risk assessment.

  20. Experimental determination of magnetohydrodynamic seawater thruster performance in a two Tesla test facility

    SciTech Connect

    Picologlou, B.; Doss, E.; Black, D.; Sikes, W.C.

    1992-09-01

    A two Tesla test facility was designed, built, and operated to investigate the performance of magnetohydrodynamic (MHD) seawater thrusters. The results of this investigation are used to validate MHD thruster performance computer models. The facility test loop, its components, and their design are presented in detail. Additionally, the test matrix and its rational are discussed. finally, representative experimental results of the test program are presented, and are compared to pretest computer model predictions. Good agreement between predicted and measured data has served to validate the thruster performance computer models.

  1. Experimental determination of magnetohydrodynamic seawater thruster performance in a two Tesla test facility

    SciTech Connect

    Picologlou, B.; Doss, E.; Black, D. ); Sikes, W.C. )

    1992-01-01

    A two Tesla test facility was designed, built, and operated to investigate the performance of magnetohydrodynamic (MHD) seawater thrusters. The results of this investigation are used to validate MHD thruster performance computer models. The facility test loop, its components, and their design are presented in detail. Additionally, the test matrix and its rational are discussed. finally, representative experimental results of the test program are presented, and are compared to pretest computer model predictions. Good agreement between predicted and measured data has served to validate the thruster performance computer models.

  2. Experimental determination of magnetohydrodynamic seawater thruster performance in a two Tesla test facility

    NASA Astrophysics Data System (ADS)

    Picologlou, B.; Doss, E.; Black, D.; Sikes, W. C.

    1992-08-01

    A two Tesla test facility was designed, built, and operated to investigate the performance of magnetohydrodynamic (MHD) seawater thrusters. The results of this investigation are used to validate MHD thruster performance computer models. The facility test loop, its components, and their design are presented in detail. Additionally, the test matrix and its rational are discussed. Finally, representative experimental results of the test program are presented, and are compared to pretest computer model predictions. Good agreement between predicted and measured data has served to validate the thruster performance computer models.

  3. Flight tests for the assessment of task performance and control activity

    NASA Technical Reports Server (NTRS)

    Pausder, H. J.; Hummes, D.

    1982-01-01

    The tests were performed with the helicopters BO 105 and UH-1D. Closely connected with tactical demands the six test pilots' task was to minimize the time and the altitude over the obstacles. The data reduction yields statistical evaluation parameters describing the control activity of the pilots and the achieved task performance. The results are shown in form of evaluation diagrams. Additionally dolphin tests with varied control strategy were performed to get more insight into the influence of control techniques. From these test results recommendations can be derived to emphasize the direct force control and to reduce the collective to pitch crosscoupling for the dolphin.

  4. 40 CFR 63.344 - Performance test requirements and test methods.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... National Emission Standards for Chromium Emissions From Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks § 63.344 Performance test requirements and test methods. (a) Performance test... compliance with the standards in § 63.342. (1) Method 306 or Method 306A, “Determination of...

  5. 40 CFR 63.344 - Performance test requirements and test methods.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... National Emission Standards for Chromium Emissions From Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks § 63.344 Performance test requirements and test methods. (a) Performance test... § 63.342. (1) Method 306 or Method 306A, “Determination of Chromium Emissions From Decorative and...

  6. 40 CFR 63.344 - Performance test requirements and test methods.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... National Emission Standards for Chromium Emissions From Hard and Decorative Chromium Electroplating and Chromium Anodizing Tanks § 63.344 Performance test requirements and test methods. (a) Performance test... compliance with the standards in § 63.342. (1) Method 306 or Method 306A, “Determination of...

  7. Measuring Several Aspects of Attention in One Test: The Factor Structure of Conners's Continuous Performance Test

    ERIC Educational Resources Information Center

    Egeland, Jens; Kovalik-Gran, Iwona

    2010-01-01

    Objective: Continuous performance tests are known to typically measure sustained attention but usually also yield parameters that potentially measure other subprocesses of attention. The aim of the present study was to test the factor structure of the Conners's Continuous Performance Test (CCPT) in a heterogeneous clinical sample consisting of…

  8. Evaluation of the JP-8+100 additive candidates in the extended duration thermal stability test system

    SciTech Connect

    Binns, K.E.; Dieterle, G.L.

    1996-10-01

    The most promising JP-8+100 additive candidates consists of dispersants, detergents, antioxidants and metal deactivators. A series of tests were conducted in the Extended Duration Thermal Stability Test System to determine the thermal stability effects of the individual JP-8+100 additives and combinations of the additives. This paper will cover the test results and their relationship to future aircraft fuel systems. The Extended Duration Thermal Stability Test System was designed to conduct long duration tests at non-accelerated temperature conditions and resident times representative or aircraft/engine fuel systems. This system and its operating characteristics will also be covered in this paper.

  9. The biobehavioral family model: testing social support as an additional exogenous variable.

    PubMed

    Woods, Sarah B; Priest, Jacob B; Roush, Tara

    2014-12-01

    This study tests the inclusion of social support as a distinct exogenous variable in the Biobehavioral Family Model (BBFM). The BBFM is a biopsychosocial approach to health that proposes that biobehavioral reactivity (anxiety and depression) mediates the relationship between family emotional climate and disease activity. Data for this study included married, English-speaking adult participants (n = 1,321; 55% female; M age = 45.2 years) from the National Comorbidity Survey Replication, a nationally representative epidemiological study of the frequency of mental disorders in the United States. Participants reported their demographics, marital functioning, social support from friends and relatives, anxiety and depression (biobehavioral reactivity), number of chronic health conditions, and number of prescription medications. Confirmatory factor analyses supported the items used in the measures of negative marital interactions, social support, and biobehavioral reactivity, as well as the use of negative marital interactions, friends' social support, and relatives' social support as distinct factors in the model. Structural equation modeling indicated a good fit of the data to the hypothesized model (χ(2)  = 846.04, p = .000, SRMR = .039, CFI = .924, TLI = .914, RMSEA = .043). Negative marital interactions predicted biobehavioral reactivity (β = .38, p < .001), as did relatives' social support, inversely (β = -.16, p < .001). Biobehavioral reactivity predicted disease activity (β = .40, p < .001) and was demonstrated to be a significant mediator through tests of indirect effects. Findings are consistent with previous tests of the BBFM with adult samples, and suggest the important addition of family social support as a predicting factor in the model.

  10. Laser-shocked energetic materials with metal additives: evaluation of chemistry and detonation performance.

    PubMed

    Gottfried, Jennifer L; Bukowski, Eric J

    2017-01-20

    A focused, nanosecond-pulsed laser has been used to ablate, atomize, ionize, and excite milligram quantities of metal-doped energetic materials that undergo exothermic reactions in the laser-induced plasma. The subsequent shock wave expansion in the air above the sample has been monitored using high-speed schlieren imaging in a recently developed technique, laser-induced air shock from energetic materials (LASEM). The method enables the estimation of detonation velocities based on the measured laser-induced air-shock velocities and has previously been demonstrated for organic military explosives. Here, the LASEM technique has been extended to explosive formulations with metal additives. A comparison of the measured laser-induced air-shock velocities for TNT, RDX, DNTF, and LLM-172 doped with Al or B to the detonation velocities predicted by the thermochemical code CHEETAH for inert or active metal participation demonstrates that LASEM has potential for predicting the early time (<10  μs) participation of metal additives in detonation events. The LASEM results show that while Al is mostly inert at early times in the detonation event (confirmed from large-scale detonation testing), B is active-and reducing the amount of hydrogen present during the early chemical reactions increases the resulting estimated detonation velocities.

  11. Investigations of non-linear polymers as high performance lubricant additives

    SciTech Connect

    Robinson, Joshua W.; Bhattacharya, Priyanka; Qu, Jun; Bays, J. Timothy; Cosimbescu, Lelia

    2015-03-22

    Off-the-shelf available engine oils contain an assortment of additives that increase the performance of base oils and maximize the overall efficiency of the machine. With ever increasing requirements for fuel efficiency, the demand for novel materials that outperform older generations is also on the rise. One approach towards increasing overall efficiency is to reduce internal friction and wear in an engine. From an additive approach, this is typically achieved by altering the bulk oil’s viscosity at high temperatures via polymers. In general, the hydrodynamic volume of polymers increase (expand) at elevated temperatures and decrease (contract/deflate) with declining temperatures and this effect is enhanced be carefully designing specific structures and architectures. The natural thinning tendency of base oil with increasing temperatures is in part mitigated by the expansion of the macromolecules added, and the overall effect is decreasing the viscosity losses at high temperatures. Traditional polymer architectures vary from linear to dendritic, where linear polymers of the same chemical composition and molecular weight to its dendritic counterpart will undergo a more significant free volume change in solution with regards to temperature changes. This advantage has been exploited in the literature towards the production of viscosity modifiers. However, one major disadvantage of linear polymers is degradation due to mechanical shear forces and high temperatures causing a shorter additive lifetime. Dendrimers on the other hand are known to demonstrate superior robustness to shear degradation when compared to their respective linear counterparts. An additional advantage of the dendritic architecture is the ability to tailor the peripheral end-groups towards influencing polymer-solvent and/or polymer-surface interactions. Comb-burst hyperbranched polymers are a hybrid of the aforementioned architectures and provide several compromises between the traditional

  12. High performance of N-alkoxycarbonyl-imines in triethylborane-mediated tin-free radical addition.

    PubMed

    Yamada, Ken-ichi; Konishi, Takehito; Nakano, Mayu; Fujii, Shintaro; Cadou, Romain; Yamamoto, Yasutomo; Tomioka, Kiyoshi

    2012-02-03

    Triethylborane-mediated tin-free radical alkylation of N-alkoxycarbonyl-imines, such as N-Boc-, N-Cbz-, and N-Teoc-imines, proceeded smoothly at a low temperature (-78 to -20 °C) to give the corresponding adducts in high yield. Although the formation of isocyanate was the major unfavorable reaction at room temperature, a one-pot conversion of N-Boc-imine to N-ethoxycarbonyl-adduct was possible through the corresponding isocyanate generated in situ. The higher performance of N-alkoxycarbonyl-imine than those of N-Ts- and N-PMP-imines is rationalized by a moderate electron-withdrawing character of an alkoxycarbonyl group that makes both addition of alkyl radical and trapping of the resulting aminyl radical by triethylborane efficiently fast.

  13. Additive Manufacturing and High-Performance Computing: a Disruptive Latent Technology

    NASA Astrophysics Data System (ADS)

    Goodwin, Bruce

    2015-03-01

    This presentation will discuss the relationship between recent advances in Additive Manufacturing (AM) technology, High-Performance Computing (HPC) simulation and design capabilities, and related advances in Uncertainty Quantification (UQ), and then examines their impacts upon national and international security. The presentation surveys how AM accelerates the fabrication process, while HPC combined with UQ provides a fast track for the engineering design cycle. The combination of AM and HPC/UQ almost eliminates the engineering design and prototype iterative cycle, thereby dramatically reducing cost of production and time-to-market. These methods thereby present significant benefits for US national interests, both civilian and military, in an age of austerity. Finally, considering cyber security issues and the advent of the ``cloud,'' these disruptive, currently latent technologies may well enable proliferation and so challenge both nuclear and non-nuclear aspects of international security.

  14. Bifunctional hairy silica nanoparticles as high-performance additives for lubricant

    NASA Astrophysics Data System (ADS)

    Sui, Tianyi; Song, Baoyu; Wen, Yu-Ho; Zhang, Feng

    2016-03-01

    Bifunctional hairy silica nanoparticles (BHSNs), which are silica nanoparticles covered with alkyl and amino organic chains, were prepared as high-performance additives for lubricants. Compared with hairy silica nanoparticles covered by a single type of organic chain, binary hairy silica nanoparticles exhibit the advantages of both types of organic chains, which exhibit excellent compatibility with lubricants and adsorbability to metal surfaces. Nanoparticles with different ratios of amino and alkyl ligands were investigated. In comparison to an untreated lubricant, BHSNs reduce the friction coefficient and wear scar diameter by 40% and 60%, respectively. The wear mechanism of BHSNs was investigated, and the protective and filling effect of the nanoparticles improved because of collaboration of amino and alkyl ligands.

  15. Bifunctional hairy silica nanoparticles as high-performance additives for lubricant

    PubMed Central

    Sui, Tianyi; Song, Baoyu; Wen, Yu-ho; Zhang, Feng

    2016-01-01

    Bifunctional hairy silica nanoparticles (BHSNs), which are silica nanoparticles covered with alkyl and amino organic chains, were prepared as high-performance additives for lubricants. Compared with hairy silica nanoparticles covered by a single type of organic chain, binary hairy silica nanoparticles exhibit the advantages of both types of organic chains, which exhibit excellent compatibility with lubricants and adsorbability to metal surfaces. Nanoparticles with different ratios of amino and alkyl ligands were investigated. In comparison to an untreated lubricant, BHSNs reduce the friction coefficient and wear scar diameter by 40% and 60%, respectively. The wear mechanism of BHSNs was investigated, and the protective and filling effect of the nanoparticles improved because of collaboration of amino and alkyl ligands. PMID:26936117

  16. Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

    NASA Technical Reports Server (NTRS)

    Zusack, Steven

    2016-01-01

    I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM

  17. High SO{sub 2} removal efficiency testing: Results of DBA and sodium formate additive tests at Southwestern Electric Power company`s Pirkey Station

    SciTech Connect

    1996-05-30

    Tests were conducted at Southwestern Electric Power Company`s (SWEPCo) Henry W. Pirkey Station wet limestone flue gas desulfurization (FGD) system to evaluate options for achieving high sulfur dioxide removal efficiency. The Pirkey FGD system includes four absorber modules, each with dual slurry recirculation loops and with a perforated plate tray in the upper loop. The options tested involved the use of dibasic acid (DBA) or sodium formate as a performance additive. The effectiveness of other potential options was simulated with the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) after it was calibrated to the system. An economic analysis was done to determine the cost effectiveness of the high-efficiency options. Results are-summarized below.

  18. Additional testing of the inlets designed for a tandem fan V/STOL nacelle

    NASA Technical Reports Server (NTRS)

    Ybarra, A. H.

    1981-01-01

    The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

  19. Cognitive fatigue influences students’ performance on standardized tests

    PubMed Central

    Sievertsen, Hans Henrik; Gino, Francesca; Piovesan, Marco

    2016-01-01

    Using test data for all children attending Danish public schools between school years 2009/10 and 2012/13, we examine how the time of the test affects performance. Test time is determined by the weekly class schedule and computer availability at the school. We find that, for every hour later in the day, test performance decreases by 0.9% of an SD (95% CI, 0.7–1.0%). However, a 20- to 30-minute break improves average test performance by 1.7% of an SD (95% CI, 1.2–2.2%). These findings have two important policy implications: First, cognitive fatigue should be taken into consideration when deciding on the length of the school day and the frequency and duration of breaks throughout the day. Second, school accountability systems should control for the influence of external factors on test scores. PMID:26884183

  20. Natural and synthetic antioxidant additives for improving the performance of new biolubricant formulations.

    PubMed

    Quinchia, Lida A; Delgado, Miguel A; Valencia, Concepción; Franco, José M; Gallegos, Crispulo

    2011-12-28

    Knowledge of the oxidative stability of vegetable oils for lubricant applications is a key point, because vegetable oil oxidation potential is the main disadvantage for its use as a lubricant. Oil degradation after an oxidation process can seriously affect its lubricating function and increase wear. In this work, two different methods for evaluating the oxidation stability of lubricating vegetable oils, the oxidation onset temperature, characterized through DSC measurements (ASTM E 2009-08), and the pressure drop in the oxygen pressure vessel (ASTM D 942-02), have been used. Additionally, thermogravimetric analysis and FTIR studies have also been carried out. High-oleic sunflower (HOSO) and castor (CO) oils were selected and blended with natural ((+)-α-tocopherol (TCP), propyl gallate (PG), l-ascorbic acid 6-palmitate (AP)) or synthetic antioxidants (4,4'-methylenebis(2,6-di-tert-butylphenol) (MBP)), with the aim of formulating biodegradable vegetable-based lubricants according to REACH regulation. (1) The results showed that the most effective biodegradable antioxidant is PG, comparable to MBP, whereas lower effectiveness was obtained for TCP and AP. In relation to the methods tested, DSC measurements achieve accurate data more quickly for evaluating the oxidation stability of these basestocks, showing a linear correlation with the traditional method based on the oxygen bomb test. The empirical equation obtained depends on the mechanism involved in the antioxidant activity.

  1. Enhanced CO2 adsorptive performance of PEI/SBA-15 adsorbent using phosphate ester based surfactants as additives.

    PubMed

    Cheng, Dandan; Liu, Yue; Wang, Haiqiang; Weng, Xiaole; Wu, Zhongbiao

    2015-12-01

    In this study, a series of polyetherimide/SBA-15: 2-D hexagonal P6mm, Santa Barbara USA (PEI/SBA-15) adsorbents modified by phosphoric ester based surfactants (including tri(2-ethylhexyl) phosphate (TEP), bis(2-ethylhexyl) phosphate (BEP) and trimethyl phosphonoacetate (TMPA)) were prepared for CO2 adsorption. Experimental results indicated that the addition of TEP and BEP had positive effects on CO2 adsorption capacity over PEI/SBA-15. In particular, the CO2 adsorption amount could be improved by around 20% for 45PEI-5TEP/SBA-15 compared to the additive-free adsorbent. This could be attributed to the decrease of CO2 diffusion resistance in the PEI bulk network due to the interactions between TEP and loaded PEI molecules, which was further confirmed by adsorption kinetics results. In addition, it was also found that the cyclic performance of the TEP-modified adsorbent was better than the surfactant-free one. This could be due to two main reasons, based on the results of in situ DRIFT and TG-DSC tests. First and more importantly, adsorbed CO2 species could be desorbed more rapidly over TEP-modified adsorbent during the thermal desorption process. Furthermore, the enhanced thermal stability after TEP addition ensured lower degradation of amine groups during adsorption/desorption cycles.

  2. Automated Portable Test System (APTS) - A performance envelope assessment tool

    NASA Technical Reports Server (NTRS)

    Kennedy, R. S.; Dunlap, W. P.; Jones, M. B.; Wilkes, R. L.; Bittner, A. C., Jr.

    1985-01-01

    The reliability and stability of microcomputer-based psychological tests are evaluated. The hardware, test programs, and system control of the Automated Portable Test System, which assesses human performance and subjective status, are described. Subjects were administered 11 pen-and-pencil and microcomputer-based tests for 10 sessions. The data reveal that nine of the 10 tests stabilized by the third administration; inertial correlations were high and consistent. It is noted that the microcomputer-based tests display good psychometric properties in terms of differential stability and reliability.

  3. Microstructural Modification of Sn-0.7Cu Solder Alloys by Fe/Bi-Addition for Achieving High Mechanical Performance

    NASA Astrophysics Data System (ADS)

    Ali, Bakhtiar; Sabri, Mohd Faizul Mohd; Said, Suhana Mohd; Mahdavifard, Mohammad Hossein; Sukiman, Nazatul Liana; Jauhari, Iswadi

    2017-03-01

    In this work, we studied the Fe/Bi-bearing tin-copper (Sn-0.7Cu) solders for their microstructural and mechanical properties. The microstructure was studied using field emission scanning electron microscopy (FESEM) with a backscattered electron (BSE) detector, x-ray diffraction (XRD) analysis, and energy-dispersive x-ray spectroscopy (EDX). The microstructure study showed that Fe forms very few FeSn2 intermetallic compounds (IMCs) and does not significantly alter the microstructure of Sn-0.7Cu, whereas Bi controls the size of inter-dendritic regions containing Cu6Sn5 and Ag3Sn IMCs of the alloy, as well as significantly refines its primary β-Sn dendrites. Moreover, Bi atoms dissolve in β-Sn matrix, which in turn strengthen the solder by the Bi solid solution strengthening mechanism. Such microstructural modification leads to significant improvements in various mechanical properties of the alloy, including shear strength, impact toughness, and hardness values. Shear tests were performed with a 0.25 mm/min shear speed. The results showed that shear strength improves from 16.57 MPa to 38.36 MPa with the addition of Fe/Bi to Sn-0.7Cu, raising by about 130%. The energy absorbed during impact tests was measured for samples with the help of a Charpy impact testing machine with a 5.4 m/s impact speed. The results revealed that the addition of Fe/Bi to Sn-0.7Cu improves its impact absorbed energy by over 35%, increasing it from 7.5 J to 10.3 J. Vickers hardness tests were carried out for the test samples with a 245.2 mN applied load and 10 s dwell time. The results showed that the hardness number improves from 9.89 to 24.13 with Fe/Bi to Sn-0.7Cu, increasing by about 140%.

  4. The impact of layer thickness on the performance of additively manufactured lapping tools

    NASA Astrophysics Data System (ADS)

    Williams, Wesley B.

    2015-10-01

    Lower cost additive manufacturing (AM) machines which have emerged in recent years are capable of producing tools, jigs, and fixtures that are useful in optical fabrication. In particular, AM tooling has been shown to be useful in lapping glass workpieces. Various AM machines are distinguished by the processes, materials, build times, and build resolution they provide. This research investigates the impact of varied build resolution (specifically layer resolution) on the lapping performance of tools built using the stereolithographic assembly (SLA) process in 50 μm and 100 μm layer thicknesses with a methacrylate photopolymer resin on a high resolution desktop printer. As with previous work, the lapping tools were shown to remove workpiece material during the lapping process, but the tools themselves also experienced significant wear on the order of 2-3 times the mass loss of the glass workpieces. The tool wear rates for the 100 μm and 50 μm layer tools were comparable, but the 50 μm layer tool was 74% more effective at removing material from the glass workpiece, which is attributed to some abrasive particles being trapped in the coarser surface of the 100 um layer tooling and not being available to interact with the glass workpiece. Considering the tool wear, these additively manufactured tools are most appropriate for prototype tooling where the low cost (<$45) and quick turnaround make them attractive when compared to a machined tool.

  5. High SO{sub 2} removal efficiency testing. Topical report - results of sodium formate additive tests at New York State Electric & Gas Corporation`s Kintigh Station

    SciTech Connect

    Murphy, J.

    1997-02-14

    Tests were conducted at New York State Gas & Electric`s (NYSEG`s) Kintigh Station to evaluate options for achieving high sulfur dioxide (SO{sub 2}) removal efficiency in the wet limestone flue gas desulfurization (FGD) system. This test program was one of six conducted by the U.S. Department of Energy to evaluate low-capital-cost upgrades to existing FGD systems as a means for utilities to comply with the requirements of the 1990 Clean Air Act Amendments. The upgrade option tested at Kintigh was sodium formate additive. Results from the tests were used to calibrate the Electric Power Research Institute`s (EPRI) FGD PRocess Integration and Simulation Model (FGDPRISM) to the Kintigh scrubber configuration. FGDPRISM was then used to predict system performance for evaluating conditions other than those tested. An economic evaluation was then done to determine the cost effectiveness of various high-efficiency upgrade options. These costs can be compared with the estimated market value of SO{sub 2} allowance or the expected costs of allowances generated by other means, such as fuel switching or new scrubbers, to arrive at the most cost-effective strategy for Clean Air Act compliance.

  6. Performance of Clinical Laboratories in South African Parasitology Proficiency Testing Surveys between 2004 and 2010

    PubMed Central

    Dini, Leigh; Frean, John

    2012-01-01

    Performance in proficiency testing (PT) schemes is an objective measure of a laboratory's best performance. We examined the performance of participants in two parasitology PT schemes in South Africa from 2004 through 2010. The average rates of acceptable scores over the period were 58% and 66% for the stool and blood parasite schemes, respectively. In our setting, participation in PT alone is insufficient to improve performance; a policy that provides additional resources and training seems necessary. PMID:22814470

  7. Recommended procedures for performance testing of radiobioassay laboratories: Volume 3, In vivo test phantoms

    SciTech Connect

    MacLellan, J.A.; Traub, R.J.

    1988-11-01

    Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed for the US Department of Energy and the US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard describes the procedures necessary to establish a bioassay performance-testing laboratory and program. The bioassay performance-testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped develop testing procedures as part of an effort to evaluate the draft ANSI N13.30 performance criteria by testing the existing measurement capabilities of various bioassay laboratories. This report recommends guidelines for the preparation, handling, storage, distribution, shipping, and documentation of test phantoms used for calibration of measurement systems for direct bioassay. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented.

  8. Foreword: Additive Manufacturing: Interrelationships of Fabrication, Constitutive Relationships Targeting Performance, and Feedback to Process Control

    DOE PAGES

    Carpenter, John S.; Beese, Allison M.; Bourell, David L.; ...

    2015-06-26

    Additive manufacturing (AM) offers distinct advantages over conventional manufacturing processes including the capability to both build and repair complex part shapes; to integrate and consolidate parts and thus overcome joining concerns; and to locally tailor material compositions as well as properties. Moreover, a variety of fields such as aerospace, military, automotive, and biomedical are employing this manufacturing technique as a way to decrease costs, increase manufacturing agility, and explore novel geometry/functionalities. In order to increase acceptance of AM as a viable processing method, pathways for qualifying both the material and the process need to be developed and, perhaps, standardized. Thismore » symposium was designed to serve as a venue for the international AM community—including government, academia, and industry—to define the fundamental interrelationships between feedstock, processing, microstructure, shape, mechanical behavior/materials properties, and function/performance. Eventually, insight into the connections between processing, microstructure, property, and performance will be achieved through experimental observations, theoretical advances, and computational modeling of physical processes. Finally, once this insight matures, AM will be able to move from the realm of making parts to making qualified materials that are certified for use with minimal need for post-fabrication characterization.« less

  9. Comparison of simple additive weighting (SAW) and composite performance index (CPI) methods in employee remuneration determination

    NASA Astrophysics Data System (ADS)

    Karlitasari, L.; Suhartini, D.; Benny

    2017-01-01

    The process of determining the employee remuneration for PT Sepatu Mas Idaman currently are still using Microsoft Excel-based spreadsheet where in the spreadsheet there is the value of criterias that must be calculated for every employee. This can give the effect of doubt during the assesment process, therefore resulting in the process to take much longer time. The process of employee remuneration determination is conducted by the assesment team based on some criterias that have been predetermined. The criteria used in the assessment process are namely the ability to work, human relations, job responsibility, discipline, creativity, work, achievement of targets, and absence. To ease the determination of employee remuneration to be more efficient and effective, the Simple Additive Weighting (SAW) method is used. SAW method can help in decision making for a certain case, and the calculation that generates the greatest value will be chosen as the best alternative. Other than SAW, also by using another method was the CPI method which is one of the calculating method in decision making based on performance index. Where SAW method was more faster by 89-93% compared to CPI method. Therefore it is expected that this application can be an evaluation material for the need of training and development for employee performances to be more optimal.

  10. Foreword: Additive Manufacturing: Interrelationships of Fabrication, Constitutive Relationships Targeting Performance, and Feedback to Process Control

    SciTech Connect

    Carpenter, John S.; Beese, Allison M.; Bourell, David L.; Hamilton, Reginald F.; Mishra, Rajiv; Sears, James

    2015-06-26

    Additive manufacturing (AM) offers distinct advantages over conventional manufacturing processes including the capability to both build and repair complex part shapes; to integrate and consolidate parts and thus overcome joining concerns; and to locally tailor material compositions as well as properties. Moreover, a variety of fields such as aerospace, military, automotive, and biomedical are employing this manufacturing technique as a way to decrease costs, increase manufacturing agility, and explore novel geometry/functionalities. In order to increase acceptance of AM as a viable processing method, pathways for qualifying both the material and the process need to be developed and, perhaps, standardized. This symposium was designed to serve as a venue for the international AM community—including government, academia, and industry—to define the fundamental interrelationships between feedstock, processing, microstructure, shape, mechanical behavior/materials properties, and function/performance. Eventually, insight into the connections between processing, microstructure, property, and performance will be achieved through experimental observations, theoretical advances, and computational modeling of physical processes. Finally, once this insight matures, AM will be able to move from the realm of making parts to making qualified materials that are certified for use with minimal need for post-fabrication characterization.

  11. Effect of an Additional, Parallel Capacitor on Pulsed Inductive Plasma Accelerator Performance

    NASA Technical Reports Server (NTRS)

    Polzin, Kurt A.; Sivak, Amy D.; Balla, Joseph V.

    2011-01-01

    A model of pulsed inductive plasma thrusters consisting of a set of coupled circuit equations and a one-dimensional momentum equation has been used to study the effects of adding a second, parallel capacitor into the system. The equations were nondimensionalized, permitting the recovery of several already-known scaling parameters and leading to the identification of a parameter that is unique to the particular topology studied. The current rise rate through the inductive acceleration coil was used as a proxy measurement of the effectiveness of inductive propellant ionization since higher rise rates produce stronger, potentially better ionizing electric fields at the coil face. Contour plots representing thruster performance (exhaust velocity and efficiency) and current rise rate in the coil were generated numerically as a function of the scaling parameters. The analysis reveals that when the value of the second capacitor is much less than the first capacitor, the performance of the two-capacitor system approaches that of the single-capacitor system. In addition, as the second capacitor is decreased in value the current rise rate can grow to be twice as great as the rise rate attained in the single capacitor case.

  12. Buffer additives, Mg-lime improve SO/sub 2/ scrubber performance

    SciTech Connect

    Smock, R.

    1982-08-01

    Demonstrations indicate that adipic acid and other organic buffering agents can improve the performance of limestone scrubbers for utilities using high-sulfur coal. Organic buffers used during the nine-month demonstration boosted the efficiency of sulfur dioxide (SO/sub 2/) removal from 70% to 95%. Despite legal incentives, the results are consistent with other industrial-scale and pilot-plant tests. Dibasic acids (DBA) had similar results. The low cost of buffer enhancing makes it a low-risk investment for utilities that need to bring their scrubbers into compliance with environmental standards. Scrubbers using adipic acid reduce capital costs 10% below conventional designs and annual operating costs 11%. 1 figure, 6 tables. (DCK)

  13. Improved performance of U-Mo dispersion fuel by Si addition in Al matrix.

    SciTech Connect

    Kim, Y S; Hofman, G L

    2011-06-01

    The purpose of this report is to collect in one publication and fit together work fragments presented in many conferences in the multi-year time span starting 2002 to the present dealing with the problem of large pore formation in U-Mo/Al dispersion fuel plates first observed in 2002. Hence, this report summarizes the excerpts from papers and reports on how we interpreted the relevant results from out-of-pile and in-pile tests and how this problem was dealt with. This report also provides a refined view to explain in detail and in a quantitative manner the underlying mechanism of the role of silicon in improving the irradiation performance of U-Mo/Al.

  14. 40 CFR 63.2993 - What test methods must I use in conducting performance tests?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 13 2013-07-01 2012-07-01 true What test methods must I use in conducting performance tests? 63.2993 Section 63.2993 Protection of Environment ENVIRONMENTAL PROTECTION... Fiberglass Mat Production Testing and Initial Compliance Requirements § 63.2993 What test methods must I...

  15. 40 CFR 63.2993 - What test methods must I use in conducting performance tests?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What test methods must I use in conducting performance tests? 63.2993 Section 63.2993 Protection of Environment ENVIRONMENTAL PROTECTION... Production Testing and Initial Compliance Requirements § 63.2993 What test methods must I use in...

  16. 40 CFR 63.2993 - What test methods must I use in conducting performance tests?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 13 2012-07-01 2012-07-01 false What test methods must I use in conducting performance tests? 63.2993 Section 63.2993 Protection of Environment ENVIRONMENTAL PROTECTION... Fiberglass Mat Production Testing and Initial Compliance Requirements § 63.2993 What test methods must I...

  17. 40 CFR 63.2993 - What test methods must I use in conducting performance tests?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true What test methods must I use in conducting performance tests? 63.2993 Section 63.2993 Protection of Environment ENVIRONMENTAL PROTECTION... Production Testing and Initial Compliance Requirements § 63.2993 What test methods must I use in...

  18. 40 CFR 63.2993 - What test methods must I use in conducting performance tests?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 13 2014-07-01 2014-07-01 false What test methods must I use in conducting performance tests? 63.2993 Section 63.2993 Protection of Environment ENVIRONMENTAL PROTECTION... Fiberglass Mat Production Testing and Initial Compliance Requirements § 63.2993 What test methods must I...

  19. Embedded performance validity testing in neuropsychological assessment: Potential clinical tools.

    PubMed

    Rickards, Tyler A; Cranston, Christopher C; Touradji, Pegah; Bechtold, Kathleen T

    2017-01-31

    The article aims to suggest clinically-useful tools in neuropsychological assessment for efficient use of embedded measures of performance validity. To accomplish this, we integrated available validity-related and statistical research from the literature, consensus statements, and survey-based data from practicing neuropsychologists. We provide recommendations for use of 1) Cutoffs for embedded performance validity tests including Reliable Digit Span, California Verbal Learning Test (Second Edition) Forced Choice Recognition, Rey-Osterrieth Complex Figure Test Combination Score, Wisconsin Card Sorting Test Failure to Maintain Set, and the Finger Tapping Test; 2) Selecting number of performance validity measures to administer in an assessment; and 3) Hypothetical clinical decision-making models for use of performance validity testing in a neuropsychological assessment collectively considering behavior, patient reporting, and data indicating invalid or noncredible performance. Performance validity testing helps inform the clinician about an individual's general approach to tasks: response to failure, task engagement and persistence, compliance with task demands. Data-driven clinical suggestions provide a resource to clinicians and to instigate conversation within the field to make more uniform, testable decisions to further the discussion, and guide future research in this area.

  20. Support vector machine to predict diesel engine performance and emission parameters fueled with nano-particles additive to diesel fuel

    NASA Astrophysics Data System (ADS)

    Ghanbari, M.; Najafi, G.; Ghobadian, B.; Mamat, R.; Noor, M. M.; Moosavian, A.

    2015-12-01

    This paper studies the use of adaptive Support Vector Machine (SVM) to predict the performance parameters and exhaust emissions of a diesel engine operating on nanodiesel blended fuels. In order to predict the engine parameters, the whole experimental data were randomly divided into training and testing data. For SVM modelling, different values for radial basis function (RBF) kernel width and penalty parameters (C) were considered and the optimum values were then found. The results demonstrate that SVM is capable of predicting the diesel engine performance and emissions. In the experimental step, Carbon nano tubes (CNT) (40, 80 and 120 ppm) and nano silver particles (40, 80 and 120 ppm) with nanostructure were prepared and added as additive to the diesel fuel. Six cylinders, four-stroke diesel engine was fuelled with these new blended fuels and operated at different engine speeds. Experimental test results indicated the fact that adding nano particles to diesel fuel, increased diesel engine power and torque output. For nano-diesel it was found that the brake specific fuel consumption (bsfc) was decreased compared to the net diesel fuel. The results proved that with increase of nano particles concentrations (from 40 ppm to 120 ppm) in diesel fuel, CO2 emission increased. CO emission in diesel fuel with nano-particles was lower significantly compared to pure diesel fuel. UHC emission with silver nano-diesel blended fuel decreased while with fuels that contains CNT nano particles increased. The trend of NOx emission was inverse compared to the UHC emission. With adding nano particles to the blended fuels, NOx increased compared to the net diesel fuel. The tests revealed that silver & CNT nano particles can be used as additive in diesel fuel to improve complete combustion of the fuel and reduce the exhaust emissions significantly.

  1. Cross-cultural effects on IQ test performance: a review and preliminary normative indications on WAIS-III test performance.

    PubMed

    Shuttleworth-Edwards, Ann B; Kemp, Ryan D; Rust, Annegret L; Muirhead, Joanne G L; Hartman, Nigel P; Radloff, Sarah E

    2004-10-01

    This article presents a review of cross-cultural influences on Wechsler IQ tests, together with a preliminary investigation into WAIS-III test performance (English administration) for a southern African sample (age range 19-30) stratified for white English first language and black African first language, level and quality of education. ('African language' is the term used to denote the indigenous languages of black populations in southern Africa). A two-way ANOVA revealed highly significant effects for both level and quality of education within the black African first language group. Scores for the white English and black African first language groups with advantaged education were comparable with the US standardization, whereas scores for black African first language participants with disadvantaged education were significantly lower than this. Thus indications from this research are that normative studies should take account of the influential variable of quality of education, in addition to level of education. Alternatively faulty conclusions may be drawn about the effects of ethnicity, with the potential for neuropsychological misdiagnosis.

  2. Preliminary supersonic flight test evaluation of performance seeking control

    NASA Technical Reports Server (NTRS)

    Orme, John S.; Gilyard, Glenn B.

    1993-01-01

    Digital flight and engine control, powerful onboard computers, and sophisticated controls techniques may improve aircraft performance by maximizing fuel efficiency, maximizing thrust, and extending engine life. An adaptive performance seeking control system for optimizing the quasi-steady state performance of an F-15 aircraft was developed and flight tested. This system has three optimization modes: minimum fuel, maximum thrust, and minimum fan turbine inlet temperature. Tests of the minimum fuel and fan turbine inlet temperature modes were performed at a constant thrust. Supersonic single-engine flight tests of the three modes were conducted using varied after burning power settings. At supersonic conditions, the performance seeking control law optimizes the integrated airframe, inlet, and engine. At subsonic conditions, only the engine is optimized. Supersonic flight tests showed improvements in thrust of 9 percent, increases in fuel savings of 8 percent, and reductions of up to 85 deg R in turbine temperatures for all three modes. The supersonic performance seeking control structure is described and preliminary results of supersonic performance seeking control tests are given. These findings have implications for improving performance of civilian and military aircraft.

  3. Nutritional and productive performance of dairy cows fed corn silage or sugarcane silage with or without additives.

    PubMed

    de Andrade, Felipe Leite; Rodrigues, João Paulo Pacheco; Detmann, Edenio; Valadares Filho, Sebastião de Campos; Castro, Marcelo Messias Duarte; Trece, Aline Souza; Silva, Tadeu Eder; Fischer, Vivian; Weiss, Kirsten; Marcondes, Marcos Inácio

    2016-04-01

    The objective of this study was to compare the intake, digestibility, and performance of dairy cows fed corn silage, fresh sugarcane, and sugarcane ensiled in three different forms. Twenty-five Holstein cows at 114 ± 12.6 days in milk (DIM) were used. A randomized block design was adopted, using an arrangement of repeated measures over time. The following treatments were tested: corn silage (CS); fresh sugarcane (FS); sugarcane silage without additives (SCS); sugarcane silage enriched with calcium oxide at 5 g/kg of forage (SCSc); and sugarcane silage enriched with Lactobacillus buchneri at 5 × 10(4) cfu/kg of forage (SCSb). The roughage to concentrate ratio was 60:40 for the CS diet and 40:60 for the sugarcane-based diets. The dry matter intake (DMI) as a function of body weight had a downward trend for the cows fed sugarcane silage, compared with those fed FS. The sugarcane silages had higher digestibilities of dry matter (DM), organic matter (OM), and neutral detergent fiber (NDFap), compared with FS. The use of L. buchneri or calcium oxide improved the diet's digestibility. The use of FS, sugarcane silage, or sugarcane silage with additives had no effects on milk and fat-corrected milk yield, compared to corn silage. Cows fed FS presented lower milk total solids content and had a downward trend for milk fat, compared with cows fed sugarcane-silage diets. Cows fed sugarcane silages produced milk with higher casein stability in the alcohol test than cows fed fresh-sugarcane diet. Sugarcane silage, with or without additives, did not reduce the intake of dairy cows, and the use of additives improved the fiber's digestibility.

  4. Achievement Test Performance of Intellectually Advanced Preschool Children.

    ERIC Educational Resources Information Center

    Shorr, David N.; And Others

    1980-01-01

    The study assessed the feasibility of using the Peabody Individual Achievement Test (PIAT) with 24 intellectually precocious preschoolers. Ss' performances suggested that the PIAT is an appropriate instrument for assessing the academic skills of intellectually advanced preschoolers. (SBH)

  5. Heritability in cognitive performance: evidence using computer-based testing.

    PubMed

    Hervey, Aaron S; Greenfield, Kathryn; Gualtieri, C Thomas

    2012-01-01

    There is overwhelming evidence of genetic influence on cognition. The effect is seen in general cognitive ability, as well as in specific cognitive domains. A conventional assessment approach using face-to-face paper and pencil testing is difficult for large-scale studies. Computerized neurocognitive testing is a suitable alternative. A total of 267 parent-child dyads were selected from a larger database of computerized neurocognitive test results. Correlations were determined between parent-child dyads, as well as matched parent-child dyads. Univariate regression analyses were estimated to determine the extent to which children's performance could be accounted for by that of their parents, compared with matched control parents. Multiple significant positive correlations in neurocognitive test performance were found in parent-child dyads. Parent performance accounted for a greater proportion of variability in every case. These findings indicated that a computerized neurocognitive battery is an effective tool for studying heritability in cognitive performance in a large sample.

  6. An improved method for testing performance of vidicons during vibration

    NASA Technical Reports Server (NTRS)

    Corson, B. R.

    1966-01-01

    Vidicon electron beam modulation is used for checking the performance of vidicons in mechanical vibration tests. The vidicon electron beam is modulated with an external signal during the write period thereby storing the image on the vidicon face.

  7. 40 CFR 63.344 - Performance test requirements and test methods.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... multiple affected sources performing the same type of operation (e.g., all are performing hard chromium... the add-on air pollution control device. (3) When multiple affected sources performing the same type... calculated time is the minimum sample time required per test run. (iii) Perform Method 306 or 306A...

  8. Impact of an additional chronic BDNF reduction on learning performance in an Alzheimer mouse model

    PubMed Central

    Psotta, Laura; Rockahr, Carolin; Gruss, Michael; Kirches, Elmar; Braun, Katharina; Lessmann, Volkmar; Bock, Jörg; Endres, Thomas

    2015-01-01

    There is increasing evidence that brain-derived neurotrophic factor (BDNF) plays a crucial role in Alzheimer’s disease (AD) pathology. A number of studies demonstrated that AD patients exhibit reduced BDNF levels in the brain and the blood serum, and in addition, several animal-based studies indicated a potential protective effect of BDNF against Aβ-induced neurotoxicity. In order to further investigate the role of BDNF in the etiology of AD, we created a novel mouse model by crossing a well-established AD mouse model (APP/PS1) with a mouse exhibiting a chronic BDNF deficiency (BDNF+/−). This new triple transgenic mouse model enabled us to further analyze the role of BDNF in AD in vivo. We reasoned that in case BDNF has a protective effect against AD pathology, an AD-like phenotype in our new mouse model should occur earlier and/or in more severity than in the APP/PS1-mice. Indeed, the behavioral analysis revealed that the APP/PS1-BDNF+/−-mice show an earlier onset of learning impairments in a two-way active avoidance task in comparison to APP/PS1- and BDNF+/−-mice. However in the Morris water maze (MWM) test, we could not observe an overall aggrevated impairment in spatial learning and also short-term memory in an object recognition task remained intact in all tested mouse lines. In addition to the behavioral experiments, we analyzed the amyloid plaque pathology in the APP/PS1 and APP/PS1-BDNF+/−-mice and observed a comparable plaque density in the two genotypes. Moreover, our results revealed a higher plaque density in prefrontal cortical compared to hippocampal brain regions. Our data reveal that higher cognitive tasks requiring the recruitment of cortical networks appear to be more severely affected in our new mouse model than learning tasks requiring mainly sub-cortical networks. Furthermore, our observations of an accelerated impairment in active avoidance learning in APP/PS1-BDNF+/−-mice further supports the hypothesis that BDNF deficiency

  9. Addition of meloxicam to the treatment of clinical mastitis improves subsequent reproductive performance.

    PubMed

    McDougall, S; Abbeloos, E; Piepers, S; Rao, A S; Astiz, S; van Werven, T; Statham, J; Pérez-Villalobos, N

    2016-03-01

    A blinded, negative controlled, randomized intervention study was undertaken to test the hypothesis that addition of meloxicam, a nonsteroidal anti-inflammatory drug, to antimicrobial treatment of mild to moderate clinical mastitis would improve fertility and reduce the risk of removal from the herd. Cows (n=509) from 61 herds in 8 regions (sites) in 6 European countries were enrolled. Following herd-owner diagnosis of mild to moderate clinical mastitis within the first 120 d of lactation in a single gland, the rectal temperature, milk appearance, and California Mastitis Test score were assessed. Cows were randomly assigned within each site to be treated either with meloxicam or a placebo (control). All cows were additionally treated with 1 to 4 intramammary infusions of cephalexin and kanamycin at 24-h intervals. Prior to treatment and at 14 and 21 d posttreatment, milk samples were collected for bacteriology and somatic cell count. Cows were bred by artificial insemination and pregnancy status was subsequently defined. General estimating equations were used to determine the effect of treatment (meloxicam versus control) on bacteriological cure, somatic cell count, the probability of being inseminated by 21 d after the voluntary waiting period, the probability of conception to first artificial insemination, the number of artificial insemination/conception, the probability of pregnancy by 120 or 200 d postcalving, and the risk of removal by 300 d after treatment. Cox's proportional hazards models were used to test the effect of treatment on the calving to first insemination and calving to conception intervals. Groups did not differ in terms of age, clot score, California Mastitis Test score, rectal temperature, number of antimicrobial treatments given or bacteria present at the time of enrollment, but cows treated with meloxicam had greater days in milk at enrollment. Cows treated with meloxicam had a higher bacteriological cure proportion than those treated with

  10. Proposed Performance Evaluation Acceptance Test for Heat Recovery Incinerators

    DTIC Science & Technology

    1988-08-01

    1985). D 3176, Method for Ultimate Analysis of Coal and Coke (1984). D 3180, Method for Calculating Coal and Coke Analyses from As-Determined to Differ...or approval of the use of such commercial products . The findings of this report are not to be construed as an official Department of the Army position...such as coal or oil fired boilers, no standard performance test is available to assess field performance or to use as an acceptance test for the HRI

  11. Soldier Performance Research Project: Armor Field and SIMNET Tests

    DTIC Science & Technology

    1989-09-01

    Event 5. The crew will react to an ATGM ambush. The TC must issue the contact report and fire command (both timed). The tank should take evasive ...Cammand’s (TEXO34) Armor and Engineer Board who conducted the Soldier Performance Research Project (SPRP) Armor tests: MC Royce Simson, Test Director CPI...the Soldier Performance Research Project (SPP), the Armor portion was conducted in two phases to provide a rigorous assessment of the cognitive skill

  12. National Unmanned Aerial System Standardized Performance Testing and Rating (NUSTAR)

    NASA Technical Reports Server (NTRS)

    Kopardekar, Parimal

    2016-01-01

    The overall objective of the NUSTAR Capability is to offer standardized tests and scenario conditions to assess performance of the UAS. The following are goals of the NU-STAR: 1. Create a prototype standardized tests and scenarios that vehicles can be tested against. 2. Identify key performance parameters of all UAS and their standardized measurement strategy. 3. Develop standardized performance reporting method (e.g., consumer report style) to assist prospective buyers. 4. Identify key performance metrics that could be used by judged towards overall safety of the UAS and operations. 5. If vehicle certification standard is made by a regulatory agency, the performance of individual UAS could be compared against the minimum requirement (e.g., sense and avoid detection time, stopping distance, kinetic energy, etc.).

  13. Prediction of sprint triathlon performance from laboratory tests.

    PubMed

    Van Schuylenbergh, R; Eynde, B Vanden; Hespel, P

    2004-01-01

    This study investigated whether sprint triathlon performance can be adequately predicted from laboratory tests. Ten triathletes [mean (SEM), age 21.8 (0.3) years, height 179 (2) cm, body mass 67.5 (2.5) kg] performed two graded maximal exercise test in random order, either on their own bicycle which was mounted on an ergometer or on a treadmill, to determine their peak oxygen consumption ( VO(2)peak). Furthermore, they participated in two to three 30-min constant-load tests in both swimming, cycling and running to establish their maximal lactate steady state (MLSS) in each exercise mode. Swim tests were performed in a 25-m swimming pool (water temperature 27 degrees C). During each test heart rate (HR), power output (PO) or running/swimming speed and blood lactate concentration (BLC) were recorded at regular intervals. Oxygen uptake ( VO(2)) was continuously measured during the graded tests. Two weeks after the laboratory tests all subjects competed in a triathlon race (500 m swim, 20-km bike, 5-km run) [1 h 4 min 45 s (1 min 38 s)]. Peak HR was 7 beats.min(-1) lower in the graded cycle test than in the treadmill test ( p<0.05) at similar peak BLC (approximately 10 mmol.l(-1)) and VO(2)peak (approximately 5 L.min(-1)). High correlations were found between VO(2)peak during cycling ( r=-0.71, p<0.05) or running ( r=-0.69, p<0.05) and triathlon performance. Stepwise multiple regression analysis showed that running speed and swimming speed at MLSS, together with BLC in running at MLSS, yielded the best prediction of performance [1 h 5 min 18 s (1 min 49 s)]. Thus, our data indicate that exercise tests aimed to determine MLSS in running and swimming allow for a precise estimation of sprint triathlon performance.

  14. The DOE ETV-1 Electric Test Vehicle. Phase 3: Performance Testing and system evaluation

    NASA Technical Reports Server (NTRS)

    Kurtz, D.

    1981-01-01

    Engineering tests were conducted in order to characterize overall system performance and component efficiencies within the system environment. A dynamometer was used in order to minimize the ambient effects and large uncertainties present in track testing. Extensive test requirements were defined and procedures were carefully controlled in order to maintain a high degree of credibility. Limited track testing was performed in order to corroborate the dynamometer results. Test results include an energy flow analysis through the major subsystems and incorporate the aerodynamic and rolling losses under cyclic and various steady speed conditions. The major output from all relevant dynamometer and track tests is also included.

  15. Test plan for performance testing of the Eaton AC-3 electric vehicle

    SciTech Connect

    Crumley, R.L.; Heiselmann, H.W.

    1985-04-01

    An alternating current (ac) propulsion system for an electric vehicle has been developed and tested by the Eaton Corporation. The test bed vehicle is a modified 1981 Mercury Lynx. The test plan has been prepared specifically for the third modification to this test bed and identified as the Eaton AC-3. The scope of the EG and G testing at INEL to be done on the Eaton AC-3 will include coastdown and dynamometer tests but will not include environmental, on-road, or track testing. Coastdown testing will be performed in accordance with SAE J-1263 (SAE Recommended Practice for Road Load Measurement and Dynamometer Simulation Using Coastdown Techniques).

  16. Review and evaluation of literature on testing of chemical additives for scale control in geothermal fluids. Final report

    SciTech Connect

    Crane, C.H.; Kenkeremath, D.C.

    1981-01-01

    A selected group of reported tests of chemical additives in actual geothermal fluids are reviewed and evaluated to summarize the status of chemical scale-control testing and identify information and testing needs. The task distinguishes between scale control in the cooling system of a flash plant and elsewhere in the utilization system due to the essentially different operating environments involved. Additives for non-cooling geothermal fluids are discussed by scale type: silica, carbonate, and sulfide.

  17. Fracture testing and performance of beryllium copper alloy C 17510

    SciTech Connect

    Murray, H.A.; Zatz, I.J. . Plasma Physics Lab.); Ratka, J.O. )

    1992-01-01

    A series of test programs was undertaken on copper beryllium alloy C 17510 for several variations in material process and chemistry. These variations in C 17510 were primarily optimized for combinations of strength and conductivity. While originally intended for use as cyclically loaded high-field, high-strength conductors in fusion energy research, material testing of C 17510 has indicated that it is an attractive and economical alternative for a host of other structural, mechanical and electrical applications. ASTM tests performed on three variations of C 17510 alloys included both J-integral and plane strain fracture toughness testing (E813, E399) and fatigue crack growth rate tests (E647), as well as verifying tensile, hardness, Charpy, and other well defined mechanical properties. Fracture testing was performed at both room and liquid nitrogen temperatures, which bound the thermal environment anticipated for the fusion components being designed. Fatigue crack propagation stress ratios ranged from nominal zero to minus one at each temperature.

  18. Fracture testing and performance of beryllium copper alloy C 17510

    SciTech Connect

    Murray, H.A.; Zatz, I.J.; Ratka, J.O.

    1992-12-01

    A series of test programs was undertaken on copper beryllium alloy C 17510 for several variations in material process and chemistry. These variations in C 17510 were primarily optimized for combinations of strength and conductivity. While originally intended for use as cyclically loaded high-field, high-strength conductors in fusion energy research, material testing of C 17510 has indicated that it is an attractive and economical alternative for a host of other structural, mechanical and electrical applications. ASTM tests performed on three variations of C 17510 alloys included both J-integral and plane strain fracture toughness testing (E813, E399) and fatigue crack growth rate tests (E647), as well as verifying tensile, hardness, Charpy, and other well defined mechanical properties. Fracture testing was performed at both room and liquid nitrogen temperatures, which bound the thermal environment anticipated for the fusion components being designed. Fatigue crack propagation stress ratios ranged from nominal zero to minus one at each temperature.

  19. Thermal Performance Testing of EMU and OSS Liquid Cooling Garments

    NASA Technical Reports Server (NTRS)

    Rhodes, Richard; Bue, Grant; Hakam, Mary

    2012-01-01

    A test was conducted to evaluate three factors influencing the thermal performance of liquid cooling garments (LCG): (1) the comparable thermal performance of an Oceaneering developed engineering evaluation unit (EEU) prototype LDG, (2) the effect of the thermal comfort undergarment (TCU), and (3) the performance of a torso or upper body only LCG configuration. To evaluate the thermal performance of each configuration a metabolic test was conducted, utilizing suited subjects to generate the metabolic heat. For this study three (3) test subjects of similar health and weight produced a metabolic load on the LDG configuration by either resting (300-600 BTU/hr), walking at a slow pace (1200 BRU/hr), and walking at a brisk pace (2200 BTU/hr), as outlined in Figure 1, the metabolic profile. During the test, oxygen consumption, heart rate, relative humidity, air flow, inlet and outlet air pressure, inlet and outlet air temperature, delta air temperature, water flow (100 lb/hr), inlet water temperature (64 F), delta water temperature, water pressure, core body temperature, skin temperature, and sweat loss data was recorded. Four different test configurations were tested, with one configuration tested twice, as outlined in Table 1. The test was conducted with the suit subjects wearing the Demonstrator Suit, pressurized to vent pressure (approximately 0.5 psig). The demonstrator suit has an integrated ventilation duct system and was used to create a relevant environment with a captured ventilation return, an integrated vent tree, and thermal insulation from the environment.

  20. 40 CFR 60.444 - Performance test procedures.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Sensitive Tape and Label Surface Coating Operations § 60.444 Performance test procedures. (a) The... average mass of VOC per mass of coating solids applied for a one calendar month period shall be determined... each test run the weighted average mass of VOC per mass of coating solids applied being used at...

  1. High explosive corner turning performance and the LANL mushroom test

    SciTech Connect

    Hill, L.G.; Seitz, W.L.; Forest, C.A.; Harry, H.H.

    1998-07-01

    The Mushroom test is designed to characterize the corner turning performance of a new generation of less sensitive booster explosives. The test is described in detail, and three corner turning figures-of-merit are examined using pure TATB (both Livermore{close_quote}s Ultrafine and a Los Alamos research blend) and PBX9504 as examples. {copyright} {ital 1998 American Institute of Physics.}

  2. High explosive corner turning performance and the LANL Mushroom test

    SciTech Connect

    Hill, L.G.; Seitz, W.L.; Forest, C.A.; Harry, H.H.

    1997-09-01

    The Mushroom test is designed to characterize the corner turning performance of a new generation of less insensitive booster explosives. The test is described in detail, and three corner turning figures-of-merit are examined using pure TATB (both Livermore`s Ultrafine and a Los Alamos research blend) and PBX9504 as examples.

  3. 40 CFR 63.1384 - Performance test requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... rate for each glass-melting furnace and, if different, the glass pull rate for each rotary spin... test. (8) The owner or operator must conduct a performance test for each rotary spin manufacturing line... affected line. (9) The owner or operator of each rotary spin manufacturing line and flame...

  4. 40 CFR 63.1384 - Performance test requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... rate for each glass-melting furnace and, if different, the glass pull rate for each rotary spin... test. (8) The owner or operator must conduct a performance test for each rotary spin manufacturing line... affected line. (9) The owner or operator of each rotary spin manufacturing line and flame...

  5. Who Are the Invalids on Continuous Performance Tests?

    ERIC Educational Resources Information Center

    O'Laughlin, Elizabeth M.; Cerny, Jerome A.; Kirby, Edward A.

    The percent and characteristics of children who produced invalid profiles on two different continuous performance tests (CPTs) tasks were examined. Sixty-one children referred for attention deficit hyperactivity disorder (ADHD) assessment and 24 non-clinical control children (all children ages 5-16) were given the Test of Variables of Attention…

  6. The Factor Structure of Test Task Characteristics and Examinee Performance

    ERIC Educational Resources Information Center

    Carr, Nathan T.

    2006-01-01

    The present study focuses on the task characteristics of reading passages and key sentences in a test of second language reading. Using a new methodological approach to describe variation in test task characteristics and explore how differences in these characteristics might relate to examinee performance, it posed the two following research…

  7. Path Analysis Tests of Theoretical Models of Children's Memory Performance

    ERIC Educational Resources Information Center

    DeMarie, Darlene; Miller, Patricia H.; Ferron, John; Cunningham, Walter R.

    2004-01-01

    Path analysis was used to test theoretical models of relations among variables known to predict differences in children's memory--strategies, capacity, and metamemory. Children in kindergarten to fourth grade (chronological ages 5 to 11) performed different memory tasks. Several strategies (i.e., sorting, clustering, rehearsal, and self-testing)…

  8. 47 CFR 76.1705 - Performance tests (channels delivered).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 4 2011-10-01 2011-10-01 false Performance tests (channels delivered). 76.1705... tests (channels delivered). The operator of each cable television system shall maintain at its local office a current listing of the cable television channels which that system delivers to its subscribers....

  9. 47 CFR 76.1705 - Performance tests (channels delivered).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Performance tests (channels delivered). 76.1705... tests (channels delivered). The operator of each cable television system shall maintain at its local office a current listing of the cable television channels which that system delivers to its subscribers....

  10. Performing Identities in Speaking Tests: Co-Construction Revisited

    ERIC Educational Resources Information Center

    Norton, Julie

    2013-01-01

    Poststructuralist perspectives on the discursive construction of identity and critical approaches to linguistics, discourse analysis, and language testing have contributed to a growing awareness of the complex social nature of performance in speaking tests. In this article, I explore how the concept of co-construction is useful to understand how…

  11. 40 CFR 1066.425 - Performing emission tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... specifications before you perform this testing. (c) Figure 1 and Figure 2 of this section show the range of... temperature range specified in § 1066.420(c)(1) throughout the test. Also measure humidity if required, such... the phase-weighted composite Energy Based Drive Metrics for the criteria specified in this...

  12. 40 CFR 63.7 - Performance testing requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... owner or operator of a new or reconstructed source subject to that standard for which construction or... performance test in order to provide a measure of test data bias. Gaseous audit samples are designed to audit... solid audit sample is designed to audit the sampling system, it must also be collected by the...

  13. 40 CFR 63.7 - Performance testing requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... owner or operator of a new or reconstructed source subject to that standard for which construction or... performance test in order to provide a measure of test data bias. Gaseous audit samples are designed to audit... solid audit sample is designed to audit the sampling system, it must also be collected by the...

  14. Printing Performance School Readiness Test: Administration and Scoring Manual.

    ERIC Educational Resources Information Center

    Simner, Marvin L.

    The Printing Performance School Readiness Test is an empirically derived instrument designed to aid in the early identification of preschool children who are at risk for school failure. The test is based on the outcome of a research program dealing with various aspects of children's printing that involved over 400 normal, non-repeating, native…

  15. Demographically adjusted normative standards for new indices of performance on the Paced Auditory Serial Addition Task (PASAT).

    PubMed

    Gonzalez, Raul; Grant, Igor; Miller, S Walden; Taylor, Michael J; Schweinsburg, Brian C; Carey, Catherine L; Woods, Steven Paul; Norman, Marc A; Rippeth, Julie D; Martin, Eileen M; Heaton, Robert K

    2006-09-01

    The Paced Auditory Serial Addition Task (PASAT) is a complex cognitive test sensitive to neuropsychological disorders. Its traditional Total Correct score seemingly reflects multiple cognitive abilities, including attention, working memory, and processing speed. Snyder, Aniskiewicz, and Snyder (1993) modified scoring guidelines for the PASAT to give credit only for "dyads." This method emphasizes working memory operations and has been found superior to Total Correct scores at detecting cognitive impairments in several investigations. To date, normative standards are not available for the "dyad" scoring method, thus limiting its utility in clinical and research settings. The current investigation provides demographically adjusted normative data based on a sample of 500 healthy adults of varied age, education, sex, and race (African American and Caucasian) for various indices of performance on the PASAT, including "Total Dyads" obtained across the four PASAT trials. In addition, we describe and present normative data on four other indices designed to quantify various aspects of performance on the PASAT: invalid responding, effects of varied information processing speed demands, and tendency to omit responses and to make arithmetic errors.

  16. New electrolytes and electrolyte additives to improve the low temperature performance of lithium-ion batteries

    SciTech Connect

    Yang, Xiao-Qing

    2008-08-31

    In this program, two different approaches were undertaken to improve the role of electrolyte at low temperature performance - through the improvement in (i) ionic conductivity and (ii) interfacial behavior. Several different types of electrolytes were prepared to examine the feasibil.ity of using these new electrolytes in rechargeable lithium-ion cells in the temperature range of +40°C to -40°C. The feasibility studies include (a) conductivity measurements of the electrolytes, (b) impedance measurements of lithium-ion cells using the screened electrolytes with di.fferent electrochemical history such as [(i) fresh cells prior to formation cycles, (ii) after first charge, and (iii) after first discharge], (c) electrical performance of the cells at room temperatures, and (d) charge discharge behavior at various low temperatures. Among the different types of electrolytes investigated in Phase I and Phase II of this SBIR project, carbonate-based LiPF6 electrolytes with the proposed additives and the low viscous ester as a third component to the carbonate-based LiPF6 electrolytes show promising results at low temperatures. The latter electrolytes deliver over 80% of room temperature capacity at -20{degrees}C when the lithium-ion cells containing these electrolytes were charged at -20 °C. Also, there was no lithium plating when the lithium­-ion cells using C-C composite anode and LiPF{sub 6} in EC/EMC/MP electrolyte were charged at -20{degrees}C at C/5 rate. The studies of ionic conductivity and AC impedance of these new electrolytes, as well as the charge discharge characteristics of lithium-ion cells using these new electrolytes at various low temperatures provide new findings: The reduced capacity and power capability, as well as the problem of lithium plating at low temperatures charging of lithium-ion cells are primarily due to slow the lithium-ion intercalation/de-intercalation kinetics in the carbon structure.

  17. Flight electronics for vibration cancellation in cryogenic refrigerators: performance and environmental testing results

    NASA Astrophysics Data System (ADS)

    Burriesci, Lawrence G.; Cook, Eric I.; Hackett, John P.; Drummond, James R.; Mand, Gurpreet S.

    1996-10-01

    Space flight optical instruments and their support hardware must reliably operate in stressing environments for the duration of their mission. They must also survive the mechanical and thermal stresses of transportation, storage and launch. It is necessary to qualify the hardware design through environmental testing and to verify the hardware's ability to perform properly during and/or after some selected environmental tests on the ground. As a rule, flight electronics are subjected to thermal, mechanical and electromagnetic environmental testing. Thermal testing takes the form of temperature cycling over a temperature difference range (Delta) T of up to 100 degrees C for a minimum of six cycles, with additional performance verification testing at the hot and cold extremes. Mechanical testing takes the form of exposure to random vibration, sine sweep vibration, shock spectra and static loading on a centrifuge or by sine burst on a vibration table. A standard series of electromagnetic interference and electromagnetic compatibility testing is also performed.

  18. Effects of Vigorous Intensity Physical Activity on Mathematics Test Performance

    ERIC Educational Resources Information Center

    Phillips, David S.; Hannon, James C.; Castelli, Darla M.

    2015-01-01

    The effect of an acute bout of physical activity on academic performance in school-based settings is under researched. The purpose of this study was to examine associations between a single, vigorous (70-85%) bout of physical activity completed during physical education on standardized mathematics test performance among 72, eighth grade students…

  19. Joint Integration Test Facility (JITF) Engineering II Performance Measurement Plans

    DTIC Science & Technology

    2001-10-01

    Technology Management Reform Act of 1966 (also known as the Clinger-Cohen Act) and the Government Performance and Results Act of 1997, which requires...This report contains the performance measurement plan for the Joint Integration Test Facility. This is an initial plan to comply with the Information

  20. The effect of tin and antimony addition on the performance of dual function cracking catalyst (DFCC) mixtures

    SciTech Connect

    Occelli, M.L. ); Naraghi, S.M.; Krishnan, V.; Suib, S.L. )

    1992-05-01

    In 1976, the Phillips Petroleum Company successfully demonstrated that the addition of certain organo-antimony compounds to a metal-contaminated heavy gas oil reduced the deleterious effects that metals such as Ni and V have on gasoline yields, coke, and hydrogen selectivities. Nickel has little effect on the activity of a fluidized cracking catalyst (FCC) but generates large amounts of gases, placing severe demands on capabilities of gas compressors. Marketed by Phillips Petroleum Company. Phil-Ad CA antimony organics have been shown to reduce by 50% gas formation due to metal contaminants, especially nickel. However, Sb, when introduced into a fluidized cracking unit, could reduce and form SbH[sub 3], stibine, that like arsine (AsH[sub 3]) is a highly toxic compound. Procedures for the safe usage of Sb in refining operations have been outlined; when used properly, Sb-containing passivating agents did not generate any detectable stibine. Recently, it has been reported that at microactivity test conditions, the additions of diluents (such as aluminas and layered magnesium silicates) capable of selectively sorbing metal contaminants from gas oils can form dual function cracking catalysts (DFCC) that retain most of their useful cracking activity even in the presence of as much as 1.0-1.5% V. It is the purpose of this paper to report the stability of Sb- and Sn-loaded alumina particles and the effects that the addition of metal passivation compounds such as Sb and Sn have on the performance of DFCC mixtures.

  1. Beamforming for directional sources: additional estimator and evaluation of performance under different acoustic scenarios.

    PubMed

    Bouchard, Christian; Havelock, David I; Bouchard, Martin

    2011-04-01

    Beamforming is done with an array of sensors to achieve a directional or spatially-specific response by using a model of the arriving wavefront. Conventionally, a plane wave or point source model is used and this can cause decreased array gain or even total breakdown of beamforming when the source is directional. To avoid this, the authors proposed in recent work an alternative beamforming method which defines a set of "sub-beamformers," each designed to respond to a different spatial mode of the source. The outputs of the individual sub-beamformers are combined in a weighted sum to give an overall output of better quality than that of a monopole beamformer. This paper extends the previous work by introducing an additional estimator for the weighted sum and by presenting simulation results to demonstrate the relative performance of the proposed method and the different estimators for a directional source in the presence of diffuse noise, reverberation, and an interfering source. Gain optimization subject to a constraint on the white-noise gain with the proposed beamforming method is also introduced. Generally, when beamforming on directional sources, the proposed method outperforms beamforming with a point source model when the input signal-to-noise ratio (SNR) is 0 dB or higher.

  2. Validated intraclass correlation statistics to test item performance models.

    PubMed

    Courrieu, Pierre; Brand-D'abrescia, Muriele; Peereman, Ronald; Spieler, Daniel; Rey, Arnaud

    2011-03-01

    A new method, with an application program in Matlab code, is proposed for testing item performance models on empirical databases. This method uses data intraclass correlation statistics as expected correlations to which one compares simple functions of correlations between model predictions and observed item performance. The method rests on a data population model whose validity for the considered data is suitably tested and has been verified for three behavioural measure databases. Contrarily to usual model selection criteria, this method provides an effective way of testing under-fitting and over-fitting, answering the usually neglected question "does this model suitably account for these data?"

  3. Spent nuclear fuel storage -- Performance tests and demonstrations

    SciTech Connect

    McKinnon, M.A.; DeLoach, V.A.

    1993-04-01

    This report summarizes the results of heat transfer and shielding performance tests and demonstrations conducted from 1983 through 1992 by or in cooperation with the US Department of Energy (DOE), Office of Commercial Radioactive Waste Management (OCRWM). The performance tests consisted of 6 to 14 runs involving one or two loadings, usually three backfill environments (helium, nitrogen, and vacuum backfills), and one or two storage system orientations. A description of the test plan, spent fuel load patterns, results from temperature and dose rate measurements, and fuel integrity evaluations are contained within the report.

  4. Power of screening tests for colorectal cancer enhanced by high levels of M2-PK in addition to FOBT.

    PubMed

    Zaccaro, Cristina; Saracino, Ilaria Maria; Fiorini, Giulia; Figura, Natale; Holton, John; Castelli, Valentina; Pesci, Valeria; Gatta, Luigi; Vaira, Dino

    2017-02-02

    Colorectal cancer (CRC) is a multistep process that involves adenoma-carcinoma sequence. CRC can be prevented by routine screening, which can detect precancerous lesions. The aim of this study is to clarify whether faecal occult blood test (i-FOBT), tumor M2 pyruvate kinase (t-M2-PK), and endocannabinoid system molecules (cannabinoid receptors type 1-CB1, type 2-CB2, and fatty acid amide hydrolase-FAAH) might represent better diagnostic tools, alone or in combination, for an early diagnosis of CRC. An immunochemical FOB test (i-FOBT) and quantitative ELISA stool test for t-M2-PK were performed in 127 consecutive patients during a 12 month period. Endocannabinoid system molecules and t-M2-PK expression were detected by immunostaining in healthy tissues and normal mucosa surrounding adenomatous and cancerous colon lesions. i-FOBT and t-M2-PK combination leads to a better diagnostic accuracy for pre-neoplastic and neoplastic colon lesions. T-M2-PK quantification in stool samples and in biopsy samples (immunostaining) correlates with tumourigenesis stages. CB1 and CB2 are well expressed in healthy tissues, and their expression decreases in the presence of advanced stages of carcinogenesis and disappears in CRC. FAAH signal is well expressed in normal mucosa and low-risk adenoma, and increased in high-risk adenoma and carcinoma adjacent tissues. This study shows that high levels of t-M2-PK in addition to FOBT enhance the power of a CRC screening test. Endocannabinoid system molecule expression correlates with colon carcinogenesis stages. Developing future faecal tests for their quantification must be undertaken to obtain a more accurate early non-invasive diagnosis for CRC.

  5. Use of Additives to Improve Performance of Methyl Butyrate-Based Lithium-Ion Electrolytes

    NASA Technical Reports Server (NTRS)

    Smart, Marshall C.; Bugga, Ratnakumar V.

    2011-01-01

    This work addresses the need for robust rechargeable batteries that can operate well over a wide temperature range. To this end, a number of electrolyte formulations have been developed that incorporate the use of electrolyte additives to improve the high-temperature resilience, low-temperature power capability, and life characteristics of methyl butyrate-based electrolyte solutions. These electrolyte additives include mono-fluoroethylene carbonate (FEC), lithium oxalate, vinylene carbonate (VC), and lithium bis(oxalato)borate (LiBOB), which have been shown to result in improved high-temperature resilience of all carbonate-based electrolytes. Improved performance has been demonstrated of Li-ion cells with methyl butyrate-based electrolytes, including 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %); 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 2% FEC; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 4% FEC; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + lithium oxalate; 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 2% VC; and 1.20M LiPF6 in EC+EMC+MB (20:20:60 v/v %) + 0.10M LiBOB. These electrolytes have been shown to improve performance in MCMB-LiNiCoO2 and graphite-LiNi1/3Co1/3Mn1/3O2 experimental Li-ion cells. A number of LiPF6-based mixed carbonate electrolyte formulations have been developed that contain ester co-solvents, which have been optimized for operation at low temperature, while still providing reasonable performance at high temperature. For example, a number of ester co-solvents were investigated, including methyl propionate (MP), ethyl propionate (EP), methyl butyrate (MB), ethyl butyrate (EB), propyl butyrate (PB), and butyl butyrate (BB) in multi-component electrolytes of the following composition: 1.0M LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + X (20:60:20 v/v %) [where X = ester co-solvent]. ["Optimized Car bon ate and Ester-Based Li-Ion Electrolytes", NASA Tech Briefs, Vol. 32, No. 4 (April 2008), p. 56.] Focusing upon improved rate

  6. Fan Noise Source Diagnostic Test: Rotor Alone Aerodynamic Performance Results

    NASA Technical Reports Server (NTRS)

    Hughes, Christopher E.; Jeracki, Robert J.; Woodward, Richard P.; Miller, Christopher J.

    2005-01-01

    The aerodynamic performance of an isolated fan or rotor alone model was measured in the NASA Glenn Research Center 9- by 15- Foot Low Speed Wind Tunnel as part of the Fan Broadband Source Diagnostic Test conducted at NASA Glenn. The Source Diagnostic Test was conducted to identify the noise sources within a wind tunnel scale model of a turbofan engine and quantify their contribution to the overall system noise level. The fan was part of a 1/5th scale model representation of the bypass stage of a current technology turbofan engine. For the rotor alone testing, the fan and nacelle, including the inlet, external cowl, and fixed area fan exit nozzle, were modeled in the test hardware; the internal outlet guide vanes located behind the fan were removed. Without the outlet guide vanes, the velocity at the nozzle exit changes significantly, thereby affecting the fan performance. As part of the investigation, variations in the fan nozzle area were tested in order to match as closely as possible the rotor alone performance with the fan performance obtained with the outlet guide vanes installed. The fan operating performance was determined using fixed pressure/temperature combination rakes and the corrected weight flow. The performance results indicate that a suitable nozzle exit was achieved to be able to closely match the rotor alone and fan/outlet guide vane configuration performance on the sea level operating line. A small shift in the slope of the sea level operating line was measured, which resulted in a slightly higher rotor alone fan pressure ratio at take-off conditions, matched fan performance at cutback conditions, and a slightly lower rotor alone fan pressure ratio at approach conditions. However, the small differences in fan performance at all fan conditions were considered too small to affect the fan acoustic performance.

  7. Addition of carbon sorbents to reduce PCB and PAH bioavailability in marine sediments: physicochemical tests.

    PubMed

    Zimmerman, John R; Ghosh, Upal; Millward, Rod N; Bridges, Todd S; Luthy, Richard G

    2004-10-15

    The addition of activated carbon as particulate sorbent to the biologically active layer of contaminated sediment is proposed as an in-situ treatment method to reduce the chemical and biological availability of hydrophobic organic contaminants (HOCs) such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs). We report results from physicochemical experiments that assess this concept. PCB- and PAH-contaminated sediment from Hunters Point Naval Shipyard, San Francisco Bay, CA, was contacted with coke and activated carbon for periods of 1 and 6 months. Sediment treated with 3.4 wt % activated carbon showed 92% and 84% reductions in aqueous equilibrium PCB and PAH concentrations, 77% and 83% reductions in PCB and PAH uptake by semipermeable membrane devices (SPMD), respectively, and reductions in PCB flux to overlying water in quiescent systems up to 89%. Adding coke to contaminated sediment did not significantly decrease aqueous equilibrium PCB concentrations nor PCB or PAH availability in SPMD measurements. Coke decreased PAH aqueous equilibrium concentrations by 38-64% depending on coke dose and particle size. The greater effectiveness of activated carbon as compared to coke is attributed to its much greater specific surface area and a pore structure favorable for binding contaminants. The results from the physicochemical tests suggest that adding activated carbon to contaminated field sediment reduces HOC availability to the aqueous phase. The benefit is manifested relatively quickly under optimum contact conditions and improves in effectiveness with contact time from 1 to 6 months. Activated carbon application is a potentially attractive method for in-situ, nonremoval treatment of marine sediment contaminated with HOCs.

  8. Interfacial Reactions of Zn-Al Alloys with Na Addition on Cu Substrate During Spreading Test and After Aging Treatments

    NASA Astrophysics Data System (ADS)

    Gancarz, Tomasz; Pstruś, Janusz; Berent, Katarzyna

    2016-08-01

    Spreading tests for Cu substrate with Zn-Al eutectic-based alloys with 0.2, 0.5, and 1.0 wt.% of Na were studied using the sessile drop method in the presence of QJ201 flux. Spreading tests were performed for 1, 3, 8, 15, 30, and 60 min of contact, at the temperatures of 475, 500, 525, and 550 °C. After cleaning the flux residue from solidified samples, the spreading area of Zn-Al + Na on Cu was determined in accordance with ISO 9455-10:2013-03. Selected, solidified solder-substrate couples were cross-sectioned and subjected to scanning electron microscopy of the interfacial microstructure. The experiment was designed to demonstrate the effect of Na addition on the kinetics of formation and growth of CuZn, Cu5Zn8, and CuZn4 phases, which were identified using x-ray diffraction and energy-dispersive spectroscopy analysis. The addition of Na to eutectic Zn-Al caused the spreading area to decrease and the thickness of intermetallic compound layers at the interface to reduce. Samples after the spreading test at 500 °C for 1 min were subjected to aging for 1, 10, and 30 days at 120,170, and 250 °C. The greater thicknesses of IMC layers were obtained for a temperature of 250 °C. With increasing Na content in Zn-Al + Na alloys, the thickness reduced, which correlates to the highest value of activation energy for Zn-Al with 1% Na.

  9. Test suite for evaluating performance of multithreaded MPI communication.

    SciTech Connect

    Thakur, R.; Gropp, W.; Mathematics and Computer Science; Univ. of Illinois

    2009-12-01

    As parallel systems are commonly being built out of increasingly large multicore chips, application programmers are exploring the use of hybrid programming models combining MPI across nodes and multithreading within a node. Many MPI implementations, however, are just starting to support multithreaded MPI communication, often focussing on correctness first and performance later. As a result, both users and implementers need some measure for evaluating the multithreaded performance of an MPI implementation. In this paper, we propose a number of performance tests that are motivated by typical application scenarios. These tests cover the overhead of providing the MPI-THREAD-MULTIPLE level of thread safety for user programs, the amount of concurrency in different threads making MPI calls, the ability to overlap communication with computation, and other features. We present performance results with this test suite on several platforms (Linux cluster, Sun and IBM SMPs) and MPI implementations (MPICH2, Open MPI, IBM, and Sun).

  10. Double-shell tank integrity assessments ultrasonic test equipment performance test

    SciTech Connect

    Pfluger, D.C.

    1996-09-26

    A double-shell tank (DST) inspection (DSTI) system was performance tested over three months until August 1995 at Pittsburgh, Pennsylvania, completing a contract initiated in February 1993 to design, fabricate, and test an ultrasonic inspection system intended to provide ultrasonic test (UT) and visual data to determine the integrity of 28 DSTs at Hanford. The DSTs are approximately one-million-gallon underground radioactive-waste storage tanks. The test was performed in accordance with a procedure (Jensen 1995) that included requirements described in the contract specification (Pfluger 1995). This report documents the results of tests conducted to evaluate the performance of the DSTI system against the requirements of the contract specification. The test of the DSTI system also reflects the performance of qualified personnel and operating procedures.

  11. Age and task parameters in continuous performance tests for preschoolers.

    PubMed

    Hagelthorn, Kathleen M; Hiemenz, Jennifer R; Pillion, Joseph P; Mahone, E Mark

    2003-06-01

    66 children (M=56.2 mo., SD=10.9), recruited from preschool and daycare centers, were administered two continuous performance tests, one auditory and one visual. Both tests utilized a format with one target and one nontarget. Interstimulus interval was fixed at 1350 msec. for the visual test and 5000 msec. for the auditory test. The visual test produced greater rates of omission and commission errors than the auditory test. Age was significantly related to mean reaction time and response variability for both tests; however, the visual test produced an unexpected pattern of increasing response time across age groups. On both tests omission rates improved significantly with age, while commission rates were consistent across ages 3-6 years. When considering continuous performance test paradigms for preschoolers, 3-yr.-olds may need at least a 4000-msec. interstimulus interval to make a choice for the stimulus cue. Hits following an interstimulus interval shorter than 1400 msec. may reflect younger preschoolers' response to a previous stimulus.

  12. Performance testing of personnel dosimetry services. A revised procedures manual

    SciTech Connect

    Miklos, J.; Plato, P.

    1983-02-01

    The US Nuclear Regulatory Commission's pilot study of the Health Physics Society Standards Committee Standard, Criteria for Testing Personnel Dosimetry Performance, was begun in 1977. A third test of this Standard was conducted from November, 1981 through April, 1982. The objective of this Procedures Manual is to describe the procedures used for Test No. 3 which reflect the changes in the Standard from Tests No. 1 and No. 2. This Manual describes each of the radiation sources used for Test No. 3, as well as the administrative procedures used during the test program. Methods of irradiation, quality control, data analysis, record keeping, and handling large numbers of dosimeters are presented. This Manual discusses the role of the National Bureau of Standards in verifying the validity of the calibration of each radiation source. Suggestions for improving irradiation procedures are included as well as recommendations that will facilitate the operation of the permanent testing facility.

  13. On the road performance tests of electric test vehicle for correlation with road load simulator

    NASA Technical Reports Server (NTRS)

    Dustin, M. O.; Slavik, R. J.

    1982-01-01

    A dynamometer (road load simulator) is used to test and evaluate electric vehicle propulsion systems. To improve correlation between system tests on the road load simulator and on the road, similar performance tests are conducted using the same vehicle. The results of track tests on the electric propulsion system test vehicle are described. The tests include range at constant speeds and over SAE J227a driving cycles, maximum accelerations, maximum gradability, and tire rolling resistance determination. Road power requirements and energy consumption were also determined from coast down tests.

  14. On-the-road performance tests of electric test vehicle for correlation with road load simulator

    SciTech Connect

    Dustin, M.O.; Slavik, R.J.

    1982-08-01

    A special purpose dynamometer (Road Load Simulator) is being used at NASA Lewis Research Center to test and evaluate electric vehicle propulsion systems developed under DOE's Electric and Hybrid Vehicle Program. To improve correlation between system tests on the Road Load Simulator and on the road, similar performance tests are being conducted using the same vehicle. The results of track tests on the Lewis electric propulsion system test vehicle are described in this report. The tests include range at constant speeds and over SAE J227a driving cycles, maximum accelerations, maximum gradability, and tire rolling resistance determination. Road power requirements and energy consumption were also determined from coast-down tests.

  15. Does familiarity with computers affect computerized neuropsychological test performance?

    PubMed

    Iverson, Grant L; Brooks, Brian L; Ashton, V Lynn; Johnson, Lynda G; Gualtieri, C Thomas

    2009-07-01

    The purpose of this study was to determine whether self-reported computer familiarity is related to performance on computerized neurocognitive testing. Participants were 130 healthy adults who self-reported whether their computer use was "some" (n = 65) or "frequent" (n = 65). The two groups were individually matched on age, education, sex, and race. All completed the CNS Vital Signs (Gualtieri & Johnson, 2006b) computerized neurocognitive battery. There were significant differences on 6 of the 23 scores, including scores derived from the Symbol-Digit Coding Test, Stroop Test, and the Shifting Attention Test. The two groups were also significantly different on the Psychomotor Speed (Cohen's d = 0.37), Reaction Time (d = 0.68), Complex Attention (d = 0.40), and Cognitive Flexibility (d = 0.64) domain scores. People with "frequent" computer use performed better than people with "some" computer use on some tests requiring rapid visual scanning and keyboard work.

  16. RTG performance on Galileo and Ulysses and Cassini test results

    SciTech Connect

    Kelly, C. Edward; Klee, Paul M.

    1997-01-10

    Power output from telemetry for the two Galileo RTGs are shown from the 1989 launch to the recent Jupiter encounter. Comparisons of predicted, measured and required performance are shown. Similar comparisons are made for the RTG on the Ulysses spacecraft which completed its planned mission in 1995. Also presented are test results from small scale thermoelectric modules and full scale converters performed for the Cassini program. The Cassini mission to Saturn is scheduled for an October 1997 launch. Small scale module test results on thermoelectric couples from the qualification and flight production runs are shown. These tests have exceeded 19,000 hours are continuing to provide increased confidence in the predicted long term performance of the Cassini RTGs. Test results are presented for full scale units both ETGs (E-6, E-7) and RTGs (F-2, F-5) along with mission power predictions. F-5, fueled in 1985, served as a spare for the Galileo and Ulysses missions and plays the same role in the Cassini program. It has successfully completed all acceptance testing. The ten years storage between thermal vacuum tests is the longest ever experienced by an RTG. The data from this test are unique in providing the effects of long term low temperature storage on power output. All ETG and RTG test results to date indicate that the power requirements of the Cassini spacecraft will be met. BOM and EOM power margins of at least five percent are predicted.

  17. Police arrest and self-defence skills: performance under anxiety of officers with and without additional experience in martial arts.

    PubMed

    Renden, Peter G; Landman, Annemarie; Savelsbergh, Geert J P; Oudejans, Raôul R D

    2015-01-01

    We investigated whether officers with additional martial arts training experience performed better in arrest and self-defence scenarios under low and high anxiety and were better able to maintain performance under high anxiety than officers who just rely on regular police training. We were especially interested to find out whether training once a week would already lead to better performance under high anxiety. Officers with additional experience in kickboxing or karate/jiu-jitsu (training several times per week), or krav maga (training once a week) and officers with no additional experience performed several arrest and self-defence skills under low and high anxiety. Results showed that officers with additional experience (also those who trained once a week) performed better under high anxiety than officers with no additional experience. Still, the additional experience did not prevent these participants from performing worse under high anxiety compared to low anxiety. Implications for training are discussed. Practitioner summary: Dutch police officers train their arrest and self-defence skills only four to six hours per year. Our results indicate that doing an additional martial arts training once a week may lead to better performance under anxiety, although it cannot prevent that performance decreases under high anxiety compared to low anxiety.

  18. Effects of Computer-Based Test Administrations on Test Anxiety and Performance.

    ERIC Educational Resources Information Center

    Shermis, Mark D.; Lombard, Danielle

    1998-01-01

    Examines the degree to which computer and test anxiety have a predictive role in performance across three computer-administered placement tests. Subjects (72 undergraduate students) were measured with the Computer Anxiety Rating Scale, the Test Anxiety Inventory, and the Myers-Briggs Type Indicator. Results suggest that much of what is considered…

  19. Performance of the Tariff Method: validation of a simple additive algorithm for analysis of verbal autopsies

    PubMed Central

    2011-01-01

    Background Verbal autopsies provide valuable information for studying mortality patterns in populations that lack reliable vital registration data. Methods for transforming verbal autopsy results into meaningful information for health workers and policymakers, however, are often costly or complicated to use. We present a simple additive algorithm, the Tariff Method (termed Tariff), which can be used for assigning individual cause of death and for determining cause-specific mortality fractions (CSMFs) from verbal autopsy data. Methods Tariff calculates a score, or "tariff," for each cause, for each sign/symptom, across a pool of validated verbal autopsy data. The tariffs are summed for a given response pattern in a verbal autopsy, and this sum (score) provides the basis for predicting the cause of death in a dataset. We implemented this algorithm and evaluated the method's predictive ability, both in terms of chance-corrected concordance at the individual cause assignment level and in terms of CSMF accuracy at the population level. The analysis was conducted separately for adult, child, and neonatal verbal autopsies across 500 pairs of train-test validation verbal autopsy data. Results Tariff is capable of outperforming physician-certified verbal autopsy in most cases. In terms of chance-corrected concordance, the method achieves 44.5% in adults, 39% in children, and 23.9% in neonates. CSMF accuracy was 0.745 in adults, 0.709 in children, and 0.679 in neonates. Conclusions Verbal autopsies can be an efficient means of obtaining cause of death data, and Tariff provides an intuitive, reliable method for generating individual cause assignment and CSMFs. The method is transparent and flexible and can be readily implemented by users without training in statistics or computer science. PMID:21816107

  20. High-throughput stochastic tensile performance of additively manufactured stainless steel

    SciTech Connect

    Salzbrenner, Bradley C.; Rodelas, Jeffrey M.; Madison, Jonathan D.; Jared, Bradley Howell; Swiler, Laura Painton; Shen, Yu -Lin; Boyce, Brad L.

    2016-10-29

    An adage within the Additive Manufacturing (AM) community is that “complexity is free”. Complicated geometric features that normally drive manufacturing cost and limit design options are not typically problematic in AM. While geometric complexity is usually viewed from the perspective of part design, this advantage of AM also opens up new options in rapid, efficient material property evaluation and qualification. In the current work, an array of 100 miniature tensile bars are produced and tested for a comparable cost and in comparable time to a few conventional tensile bars. With this technique, it is possible to evaluate the stochastic nature of mechanical behavior. The current study focuses on stochastic yield strength, ultimate strength, and ductility as measured by strain at failure (elongation). However, this method can be used to capture the statistical nature of many mechanical properties including the full stress-strain constitutive response, elastic modulus, work hardening, and fracture toughness. Moreover, the technique could extend to strain-rate and temperature dependent behavior. As a proof of concept, the technique is demonstrated on a precipitation hardened stainless steel alloy, commonly known as 17-4PH, produced by two commercial AM vendors using a laser powder bed fusion process, also commonly known as selective laser melting. Using two different commercial powder bed platforms, the vendors produced material that exhibited slightly lower strength and markedly lower ductility compared to wrought sheet. Moreover, the properties were much less repeatable in the AM materials as analyzed in the context of a Weibull distribution, and the properties did not consistently meet minimum allowable requirements for the alloy as established by AMS. The diminished, stochastic properties were examined in the context of major contributing factors such as surface roughness and internal lack-of-fusion porosity. Lastly, this high-throughput capability is expected

  1. High-throughput stochastic tensile performance of additively manufactured stainless steel

    DOE PAGES

    Salzbrenner, Bradley C.; Rodelas, Jeffrey M.; Madison, Jonathan D.; ...

    2016-10-29

    An adage within the Additive Manufacturing (AM) community is that “complexity is free”. Complicated geometric features that normally drive manufacturing cost and limit design options are not typically problematic in AM. While geometric complexity is usually viewed from the perspective of part design, this advantage of AM also opens up new options in rapid, efficient material property evaluation and qualification. In the current work, an array of 100 miniature tensile bars are produced and tested for a comparable cost and in comparable time to a few conventional tensile bars. With this technique, it is possible to evaluate the stochastic naturemore » of mechanical behavior. The current study focuses on stochastic yield strength, ultimate strength, and ductility as measured by strain at failure (elongation). However, this method can be used to capture the statistical nature of many mechanical properties including the full stress-strain constitutive response, elastic modulus, work hardening, and fracture toughness. Moreover, the technique could extend to strain-rate and temperature dependent behavior. As a proof of concept, the technique is demonstrated on a precipitation hardened stainless steel alloy, commonly known as 17-4PH, produced by two commercial AM vendors using a laser powder bed fusion process, also commonly known as selective laser melting. Using two different commercial powder bed platforms, the vendors produced material that exhibited slightly lower strength and markedly lower ductility compared to wrought sheet. Moreover, the properties were much less repeatable in the AM materials as analyzed in the context of a Weibull distribution, and the properties did not consistently meet minimum allowable requirements for the alloy as established by AMS. The diminished, stochastic properties were examined in the context of major contributing factors such as surface roughness and internal lack-of-fusion porosity. Lastly, this high-throughput capability is

  2. 30 CFR 250.449 - What additional BOP testing requirements must I meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations.... You may use drilling fluids to conduct subsequent tests of a subsea BOP system; (c) Alternate tests... sizes of pipe in use, excluding drill collars and bottom-hole tools; (g) Pressure test affected...

  3. 46 CFR 160.035-12 - Additional preapproval tests required for F.R.P. lifeboats.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... and final measurements taken. There shall be no fractures or other signs of excessive stress and no... fractures or other signs of excessive stress and no appreciable set as a result of this test. (3) Swing test... span. The thwarts shall not fracture or otherwise be rendered unserviceable. (6) Towing test. With...

  4. Fatigue life and performance testing of hybrid ceramic ball bearings

    SciTech Connect

    Chiu, Y.P.; Prason, P.K.; Dezzani, M.

    1996-03-01

    Hybrid ceramic ball bearings are finding increased applications in machine tool spindles and aerospace vehicles. Results of three types of testing hybrid ceramic ball bearing are presented and discussed. The first is the classical endurance testing of highly loaded hybrid bearings with good lubrication. The second is the endurance test of hybrid nitrided bearings after running in a contaminated lubricant which caused dented raceways. The third is the high-speed performance testing of spindle bearings lubricated with grease or an oil-air mixture. Recent material development, bearing temperature at high-speed and reliability considerations are discussed. 14 refs., 9 fig., 4 tab.

  5. Play for Performance: Using Computer Games to Improve Motivation and Test-Taking Performance

    ERIC Educational Resources Information Center

    Dennis, Alan R.; Bhagwatwar, Akshay; Minas, Randall K.

    2013-01-01

    The importance of testing, especially certification and high-stakes testing, has increased substantially over the past decade. Building on the "serious gaming" literature and the psychology "priming" literature, we developed a computer game designed to improve test-taking performance using psychological priming. The game primed…

  6. Synergistic interactions between commonly used food additives in a developmental neurotoxicity test.

    PubMed

    Lau, Karen; McLean, W Graham; Williams, Dominic P; Howard, C Vyvyan

    2006-03-01

    Exposure to non-nutritional food additives during the critical development window has been implicated in the induction and severity of behavioral disorders such as attention deficit hyperactivity disorder (ADHD). Although the use of single food additives at their regulated concentrations is believed to be relatively safe in terms of neuronal development, their combined effects remain unclear. We therefore examined the neurotoxic effects of four common food additives in combinations of two (Brilliant Blue and L-glutamic acid, Quinoline Yellow and aspartame) to assess potential interactions. Mouse NB2a neuroblastoma cells were induced to differentiate and grow neurites in the presence of additives. After 24 h, cells were fixed and stained and neurite length measured by light microscopy with computerized image analysis. Neurotoxicity was measured as an inhibition of neurite outgrowth. Two independent models were used to analyze combination effects: effect additivity and dose additivity. Significant synergy was observed between combinations of Brilliant Blue with L-glutamic acid, and Quinoline Yellow with aspartame, in both models. Involvement of N-methyl-D-aspartate (NMDA) receptors in food additive-induced neurite inhibition was assessed with a NMDA antagonist, CNS-1102. L-glutamic acid- and aspartame-induced neurotoxicity was reduced in the presence of CNS-1102; however, the antagonist did not prevent food color-induced neurotoxicity. Theoretical exposure to additives was calculated based on analysis of content in foodstuff, and estimated percentage absorption from the gut. Inhibition of neurite outgrowth was found at concentrations of additives theoretically achievable in plasma by ingestion of a typical snack and drink. In addition, Trypan Blue dye exclusion was used to evaluate the cellular toxicity of food additives on cell viability of NB2a cells; both combinations had a straightforward additive effect on cytotoxicity. These data have implications for the

  7. Performance testing of radiobioassay laboratories: In vivo measurements, Final Report

    SciTech Connect

    MacLellan, J.A.; Traub, R.J.; Olsen, P.C.

    1990-04-01

    A study of two rounds of in vivo laboratory performance testing was undertaken by Pacific Northwest Laboratory (PNL) to determine the appropriateness of the in vivo performance criteria of draft American National Standards Institute (ANSI) standard ANSI N13.3, Performance Criteria for Bioassay.'' The draft standard provides guidance to in vivo counting facilities regarding the sensitivity, precision, and accuracy of measurements for certain categories of commonly assayed radionuclides and critical regions of the body. This report concludes the testing program by presenting the results of the Round Two testing. Testing involved two types of measurements: chest counting for radionuclide detection in the lung, and whole body counting for detection of uniformly distributed material. Each type of measurement was further divided into radionuclide categories as defined in the draft standard. The appropriateness of the draft standard criteria by measuring a laboratory's ability to attain them were judged by the results of both round One and Round Two testing. The testing determined that performance criteria are set at attainable levels, and the majority of in vivo monitoring facilities passed the criteria when complete results were submitted. 18 refs., 18 figs., 15 tabs.

  8. Test Operations Procedure (TOP) 01-1-025 Camouflage Performance Testing Using Observers

    DTIC Science & Technology

    2016-05-05

    spectral drones makes viewing angle relative to the ground plan an important consideration in test design. Further, off- the-shelf technology is no... test to be taken to the observers. Technology has changed quickly in the last decade and continues to evolve rapidly. This TOP presents a photo...Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 01-1-025 Camouflage Performance Testing Using Observers 5a

  9. End-of-Test Performance and Wear Characterization of NASA's Evolutionary Xenon Thruster (NEXT) Long-Duration Test

    NASA Technical Reports Server (NTRS)

    Shastry, Rohit; Herman, Daniel A.; Soulas, George C.; Patterson, Michael J.

    2014-01-01

    The NASA's Evolutionary Xenon Thruster (NEXT) program is developing the next-generation solar electric ion propulsion system with significant enhancements beyond the state-of-the-art NASA Solar Electric Propulsion Technology Application Readiness (NSTAR) ion propulsion system to provide future NASA science missions with enhanced capabilities. A Long-Duration Test (LDT) was initiated in June 2005 to validate the thruster service life modeling and to quantify the thruster propellant throughput capability. Testing was recently completed in February 2014, with the thruster accumulating 51,184 hours of operation, processing 918 kg of xenon propellant, and delivering 35.5 MN-s of total impulse.As part of the test termination procedure, a comprehensive performance characterization was performed across the entire NEXT throttle table. This was performed prior to planned repairs of numerous diagnostics that had become inoperable over the course of the test. After completion of these diagnostic repairs in November 2013, a comprehensive end-of-test performance and wear characterization was performed on the test article prior to exposure to atmosphere. These data have confirmed steady thruster performance with minimal degradation as well as mitigation of numerous life limiting mechanisms encountered in the NSTAR design. Component erosion rates compare favorably to pretest predictions based on semi-empirical models used for the thruster service life assessment. Additional data relating to ion beam density profiles, facility backsputter rates, facility backpressure effects on thruster telemetry, and modulation of the neutralizer keeper current are presented as part of the end-of-test characterization. Presently the test article for the NEXT LDT has been exposed to atmosphere and placed within a clean room environment, with post-test disassembly and inspection underway.

  10. 34 CFR 668.148 - Additional criteria for the approval of certain tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... quantitative problem-solving skills, the test publisher must provide— (i) A minimum of four parallel forms of... the American Educational Research Association, the American Psychological Association, and...

  11. Exercise Test Performance Reveals Evidence of the Cardiorespiratory Fitness Hypothesis.

    PubMed

    Billinger, Sandra A; Vidoni, Eric D; Morris, Jill K; Thyfault, John P; Burns, Jeffrey M

    2017-04-01

    Positive physiologic and cognitive responses to aerobic exercise have resulted in a proposed cardiorespiratory (CR) fitness hypothesis in which fitness gains drive changes leading to cognitive benefit. The purpose of this study was to directly assess the CR fitness hypothesis. Using data from an aerobic exercise trial, we examined individuals who completed cardiopulmonary and cognitive testing at baseline and 26 weeks. Change in cognitive test performance was not related to CR fitness change (r(2) = .06, p = .06). However, in the subset of individuals who gave excellent effort during exercise testing, change in cognitive test performance was related to CR fitness change (r(2) = .33, p < .01). This was largely due to change in the cognitive domain of attention (r(2) = .36, p < .01). The magnitude of change was not explained by duration of exercise. Our findings support further investigation of the CR fitness hypothesis and mechanisms by which physiologic adaptation may drive cognitive change.

  12. Relationships Between Anaerobic Performance, Field Tests and Game Performance of Sitting Volleyball Players.

    PubMed

    Marszalek, Jolanta; Molik, Bartosz; Gomez, Miguel Angel; Skučas, Kęstutis; Lencse-Mucha, Judit; Rekowski, Witold; Pokvytyte, Vaida; Rutkowska, Izabela; Kaźmierska-Kowalewska, Kalina

    2015-11-22

    The aim of this study was to evaluate relationships between anaerobic performance, field tests, game performance and anthropometric variables of sitting volleyball players. Twenty elite Polish sitting volleyball players were tested using the 30 s Wingate Anaerobic Test for arm crank ergometer and participated in six physical field tests. Heights in position to block and to spike, as well as arm reach were measured. Players were observed during the game on the court in terms of effectiveness of the serve, block, attack, receive and defense. Pearson analysis and the Spearman's rank correlation coefficient were used. The strongest correlations were found between the chest pass test and mean power and peak power (r=.846; p=.001 and r=.708; p=.0005, respectively), and also between the T-test and peak power (r= -.718; p=.001). Mean power correlated with the 3 m test (r= -.540; p=.014), the 5 m test (r= -.592; p=.006), and the T-test (r= -.582; p=.007). Peak power correlated with the 3 m test (r= -.632; p=.003), the 5 m test (r= -.613; p=.004), speed & agility (r= -.552; p=.012) and speed & endurance (r=-.546; p=.013). Significant correlations were observed between anthropometric parameters and anaerobic performance variables (p≤.001), and also between anthropometric parameters and field tests (p≤.05). Game performance and physical fitness of sitting volleyball players depended on their anthropometric variables: reach of arms, the position to block and to spike. The chest pass test could be used as a non-laboratory field test of anaerobic performance of sitting volleyball players.

  13. Outdoor performance testing of thin-film devices

    NASA Astrophysics Data System (ADS)

    1985-10-01

    The Advanced Systems Research Group supports the photovoltaic advanced R&D (PV AR&D) project by providing outdoor (global) testing of PV cells, submodules, modules, and arrays. The group also provides in house engineering and analysis to identify and determine how technical issues such as cell/module/system adaptations, long term stability, reliability, economics, materials availability, safety, and environmental impacts affect the development and ultimate use of advanced PV thin film, innovative cell, and material technologies. A major thrust of the research effort is to develop and utilize instrumentation and procedures for monitoring and analyzing PV cells and submodules including outdoor performance and stability testing and life cycle accelerated stress testing. To accomplish the above, the solar energy research institute (SERI) outdoor PV test facility was established in 1982. The group has designed testing systems and analysis procedures for, and has tested, numerous amorphous silicon thin film submodules provided by SERI subcontractors and has performed long term outdoor stability tests on CdS/CuIr Se sub 2 and hydrogen passivated silicon solar cells. A significant contribution from this facility over the past year was the testing of large area amorphous silicon submodules.

  14. Cumulative blood lead levels and neurobehavioral test performance.

    PubMed

    Chia, S E; Chia, H P; Ong, C N; Jeyaratnam, J

    1997-01-01

    The current scientific literature provides inadequate evidence to conclude whether or not cumulative exposure to or absorption of lead adversely affects performance in neurobehavioral tests in adults. One of reasons for this controversy is the lack of studies with good cumulative exposure to or dose of lead. The aims of this study are to compare the neurobehavioral test performances of a group of lead-exposed workers and a referent group, and to study the association of the neurobehavioral test performances with concurrent blood lead levels and cumulative blood lead levels. Fifty lead battery workers and 97 non-exposed (referent) workers from a vehicle maintenance workshop were evaluated on their neurobehavioral performance using the World Health Organization Neurobehavioral Core Test Battery (WHO-NCTB). The geometric mean concurrent blood lead (ConPb) of the exposed and referent groups were 37.1 (range 13.2-64.6) microg/100 ml and 6.1 (range 2.4-12.4) microg/100 ml, respectively. Cumulative blood lead (CumPb) was defined as area under the curve for the number of years each worker was exposed to lead (three workers previous blood lead results were not available). ConPb and CumPb were used to study the association with the neurobehavioral test results. The exposed group had significantly poorer manual dexterity, perceptual-motor speed, and motor steadiness compared with the referents. The standardized partial regression coefficients were higher for CumPb than ConPb for most of the neurobehavioral test results. In the group >35 years old, there were significantly stronger associations between CumPb and Digit Symbol and Trail Making Part A results than for ConPb which are tests of perceptual and motor skills. CumPb was a better predictor than ConPb of the effects of lead on neurobehavioral performances.

  15. 40 CFR 80.166 - Carburetor deposit control performance test and test fuel guidelines.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... Port and throttle body fuel injector deposit control test data will also be considered to be adequate... for demonstration of carburetor deposit control, in addition to the fuel injector test procedure... Fuel Injector (PFI) Deposits in Vehicle Engines”, March 1, 1991, Section 2257, Title 13,...

  16. Improving the environmental and performance characteristics of vehicles by introducing the surfactant additive into gasoline.

    PubMed

    Magaril, Elena; Magaril, Romen

    2016-09-01

    The operation of modern vehicles requires the introduction of package of fuel additives to ensure the required level of operating characteristics, some of which cannot be achieved by current oil refining methods. The use of additives allows flexibility of impact on the properties of the fuel at minimal cost, increasing the efficiency and environmental safety of vehicles. Among the wide assortment of additives available on the world market, many are surfactants. It has been shown that the introduction of some surfactants into gasoline concurrently reduces losses from gasoline evaporation, improves the mixture formation during injection of gasoline into the engine and improves detergent and anticorrosive properties. The surfactant gasoline additive that provides significant improvement in the quality of gasoline used and environmental and operating characteristics of vehicles has been developed and thoroughly investigated. The results of studies confirming the efficiency of the gasoline additive application are herein presented.

  17. Users manual for the Automated Performance Test System (APTS)

    NASA Technical Reports Server (NTRS)

    Lane, N. E.; Kennedy, R. S.

    1990-01-01

    The characteristics of and the user information for the Essex Automated Performance Test System (APTS) computer-based portable performance assessment battery are given. The battery was developed to provide a menu of performance test tapping the widest possible variety of human cognitive and motor functions, implemented on a portable computer system suitable for use in both laboratory and field settings for studying the effects of toxic agents and other stressors. The manual gives guidance in selecting, administering and scoring tests from the battery, and reviews the data and studies underlying the development of the battery. Its main emphasis is on the users of the battery - the scientists, researchers and technicians who wish to examine changes in human performance across time or as a function of changes in the conditions under which test data are obtained. First the how to information needed to make decisions about where and how to use the battery is given, followed by the research background supporting the battery development. Further, the development history of the battery focuses largely on the logical framework within which tests were evaluated.

  18. Performance analysis of sequential tests in process control

    SciTech Connect

    Hoyer, K.K.

    1994-04-01

    In recent years, a great deal of emphasis has been placed on quality control of industrial processes. In particular, numerous statistical techniques exist which are designed to continually check an industrial process for machine or component failure, thereby determining if the process is under control, or if it is becoming out of control. In this study, the authors consider a very powerful class of quality control techniques known as sequential tests. Sequential tests classify a set of observations in a manner similar to statistical hypothesis tests, but are characterized by a random sample size. Perhaps the best known sequential test is Wald`s sequential probability ratio test. The sequential probability ratio test (SPRT) is a log likelihood ratio based test for simple or composite hypotheses. After taking each observation, the SPRT decides whether to accept the null hypothesis, reject the null hypothesis, or continue sampling. For the purpose of quality control, an SPRT can be conducted repeatedly over time as incoming observations are received. In the following section, the authors reviews the sequential probability ratio test and state some of its properties. In Section 3, they formulate a Markov additive model which allows them to study the sequential probability ratio test under various types of process behavior. Section 4 develops the theoretical results and the methodological approach that allows them to bound the first passage time distributions of their model. Section 5 illustrates their techniques through numerical examples.

  19. Power Performance Test Report for the SWIFT Wind Turbine

    SciTech Connect

    Mendoza, I.; Hur, J.

    2012-12-01

    This report summarizes the results of a power performance test that NREL conducted on the SWIFT wind turbine. This test was conducted in accordance with the International Electrotechnical Commission's (IEC) standard, Wind Turbine Generator Systems Part 12: Power Performance Measurements of Electricity Producing Wind Turbines, IEC 61400-12-1 Ed.1.0, 2005-12. However, because the SWIFT is a small turbine as defined by IEC, NREL also followed Annex H that applies to small wind turbines. In these summary results, wind speed is normalized to sea-level air density.

  20. Performance of Bayesian outlier diagnostic in testing mean vector

    NASA Astrophysics Data System (ADS)

    Mohammad, Rofizah; Hamzah, Firdaus Mohamad

    2014-09-01

    The diagnostic measure kd which is used to measure the effect of a single observation d on model choice was applied to a variety of univariate model. The purpose of this study is to assess the performance of this diagnostic measure when applying to multivariate structure for testing the specified mean vector. We illustrate the method using data generated from multivariate normal distribution. If X a p-variate normal random variable of size n with the mean vector θ and a known covariance matrix, we consider the null hypothesis that the mean vector θ is zero. From this simulation we test the performance of kd for several n and p values.

  1. Performance correlations of five solar collectors tested simultaneously outdoors

    NASA Technical Reports Server (NTRS)

    Miller, D. R.

    1976-01-01

    Collector thermal efficiency, and efficiency degradation with time were measured for 5 flat-plate solar collectors tested simultaneously in an outdoor solar collector test facility. Results indicate that by using collector performance parameters which account for diffuse insolation, outdoor data recorded on 'cloudy' days can be used as a measure of performance, as long as the ratio of direct to total insolation exceeds approximately 0.6. These outdoor results also show good agreement with thermal efficiency data obtained indoors in a solar simulator. Significant efficiency degradation occurred on only one of the five collectors exposed to outdoor conditions for a period of one to two years.

  2. Performance correlations of five solar collectors tested simultaneously outdoors

    NASA Technical Reports Server (NTRS)

    Miller, D. R.

    1976-01-01

    Collector thermal efficiency, and efficiency degradation with time were measured for 5 flat-plate solar collectors tested simultaneously in an outdoor solar collector test facility. Results indicate that by using collector performance parameters which account for diffuse isolation, outdoor data recorded on cloud days can be used as a measure of performance, as long as the ratio of direct to total insolation exceeds approximately 0.6. These outdoor results also show good agreement with thermal efficiency data obtained indoors in a solar simulator. Significant efficiency degradation occurred on only one of the five collectors exposed to outdoor conditions for a period of one to two years.

  3. Fertilization test performance using Arbacia punctulata maintained in static culture

    SciTech Connect

    Serbst, J.R.; Wright, L.; Sheehan, C.V.; Fitzpatrick, K.

    1995-12-31

    The sea urchin fertilization test using the Atlantic urchin, Arbacia punctulata, is widely utilized in evaluating toxicity of receiving waters and effluents as part of the NPDES program. While this species is easily maintained in uncontaminated, flow-through seawater systems, laboratories without access to flowing seawater either obtain new urchins for each test or maintain populations in static cultures. This study was conducted to assess test success and reproducibility of fertilization tests conducted using urchins maintained in separate-sex, static, temperature-controlled aquaria containing filtered natural seawater. Test performance was evaluated by periodically conducting the standard sea urchin fertilization test (EPA 600/4-87-028) using a common reference toxicant, sodium dodecyl sulfate (SDS) Thirteen tests were conducted between September 1993 and May 1994 using one population of urchins, and five tests were conducted between June and December 1994 with a second population of urchins. Test success was 100% (control fertilization > 50%) with a control fertilization mean of 96.4% (S.D. = 3.3). There were no differences between mean EC{sub 50} values calculated for each set of tests (p < 0.05). The running mean value for toxicity was 7.1 mg/L (S.D. = 1.26) for 18 tests, with a CV of 17.7%, comparing favorably with values generated using urchins maintained in flowing seawater. The running mean value for toxicity in these tests was 2.4 mg/L (S.D. = 0.9) for 18 tests conducted between November 1987 and July 1989 (ASTM STP 1124). Data from all urchin tests were used to construct a control chart defining normal ranges for SDS toxicity. This study demonstrated that fertile, adult sea urchins can produce consistent toxicity responses with low variability while being maintained in static, temperature regulated culture facilities.

  4. 75 FR 2122 - Additional Guidance Regarding Application of Current Procedures for Testing Energy Consumption of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ... ensure the consistent application of DOE's current test procedure to refrigerator-freezers with French doors, bottom-mounted freezers, and through-the-door (TTD) ice service (French door TTD models). This... application of the current test procedure to refrigerator- freezers with French doors, bottom-mounted...

  5. Stereotype threat? Effects of inquiring about test takers' gender on conceptual test performance in physics

    NASA Astrophysics Data System (ADS)

    Maries, Alexandru; Singh, Chandralekha

    2015-12-01

    It has been found that activation of a stereotype, for example by indicating one's gender before a test, typically alters performance in a way consistent with the stereotype, an effect called "stereotype threat." On a standardized conceptual physics assessment, we found that asking test takers to indicate their gender right before taking the test did not deteriorate performance compared to an equivalent group who did not provide gender information. Although a statistically significant gender gap was present on the standardized test whether or not students indicated their gender, no gender gap was observed on the multiple-choice final exam students took, which included both quantitative and conceptual questions on similar topics.

  6. Performance testing of the AC propulsion ELX electric vehicle

    SciTech Connect

    Kramer, W.E.; MacDowall, R.D.; Burke, A.F.

    1994-06-01

    Performance testing of the AC Propulsion ELX electric vehicle is described. Test data are presented and analyzed. The ELX vehicle is the first of a series of electric vehicles of interest to the California Air Resources Board. The test series is being conducted under a Cooperative Research and Development Agreement (CRADA) between the US Department of energy and the California Air Resources Board. The tests which were conducted showed that the AC Propulsion ELX electric vehicle has exceptional acceleration and range performance. when the vehicle`s battery was fully charged, the vehicle can accelerate from 0 to 96 km/h in about 10 seconds. Energy consumption and range tests using consecutive FUDS and HWFET Driving cycles (the all-electric cycle) indicate that the energy economy of the AC Propulsion ELX electric vehicle with regenerative braking is 97 W{center_dot}h/km, with a range of 153 km (95 miles). Computer simulations performed using the SIMPLEV Program indicate that the vehicle would have a range of 327 km (203 miles) on the all-electric cycle if the lead acid batteries were replaced with NiMH batteries having an energy density of 67 W{center_dot}h/kg. Comparisons of FUDS test data with and without regenerative braking indicated that regenerative braking reduced the energy consumption of the ELX vehicle by approximately 25%.

  7. Performance Tests for Repeated Measures: Moran and Computer Batteries.

    DTIC Science & Technology

    1981-11-01

    Alvah C. Bittner, Jr., Robert C. Carter, and Michele Krause November 1981 NAALBIDNAIC LBRAORG New rlens, ousono/Q - 4-. UNCLASSIFIED SECURITY...Robert C. Carter, and Michele Krause 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK AREA & WORK UNIT NUMBERS Naval...So 7it NBDL - 81R012 Performance Tests for Repeated Measures: Moran and Computer Batteries Alvah C. Bittner, Jr., Robert C. Carter, and Michele Krause

  8. MIXTURES OF THYROID DISRUPTING CHEMICALS: TESTING ADDITIVITY OF HEPATIC INDUCERS AND THYROID PEROXIDASE INHIBITORS.

    EPA Science Inventory

    Humans are exposed to chemical mixtures via diet, occupation, and the environment. Previous data demonstrated that low doses of polycyclic halogenated aromatic hydrocarbons (PHAHs) acting through similar mechanisms result in an additive reduction of thyroxine (T4). If xenobioti...

  9. Tribological performance of Mg/Al/Ce layered double hydroxides nanoparticles and intercalated products as lubricant additives

    NASA Astrophysics Data System (ADS)

    Li, Shuo; Qin, Haojing; Zuo, Ranfang; Bai, Zhimin

    2015-10-01

    Mg/Al/Ce ternary layered double hydroxides (LDHs) were synthesized via coprecipitation and intercalated by succinic acid and lauric acid through ion exchange method respectively. The LDHs products were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and Fourier transform infrared (FT-IR). Tribological properties of LDHs as lubricant additives were evaluated by four-ball friction and air compressor test. The results indicated that Mg/Al/Ce LDHs were prepared successfully with Ce/Al molar ratio of 0.05 and crystallization temperature of 140 °C. The interlayer spacing of LDHs precursor was expanded by succinic acid and lauric acid to 8.838 and 17.519 Å respectively. All the three LDHs products can reduce friction and wear of engine lubricating oil in the tests. LDHs intercalated with lauric acid showed best tribological performance among them which was attributed to sliding each other between laminates, good dispersibility in oil medium and a protective tribofilm formed on the worn surface.

  10. Testing for Additivity in Chemical Mixtures Using a Fixed-Ratio Ray Design and Statistical Equivalence Testing Methods

    EPA Science Inventory

    Fixed-ratio ray designs have been used for detecting and characterizing interactions of large numbers of chemicals in combination. Single chemical dose-response data are used to predict an “additivity curve” along an environmentally relevant ray. A “mixture curve” is estimated fr...

  11. Performance testing of West Valley Reference 6 glass

    SciTech Connect

    Ebert, W.L.; Bates, J.K.

    1995-06-01

    The chemical durability of West Valley Reference 6 glass is being evaluated by using a suite of laboratory tests which highlight the early, interim, and long-term stages of corrosion. The test results are being used to describe the glass corrosion path and its long-term durability. The long-term durability of the SRL Environmental Assessment glass is being evaluated for comparison. Test results also provide parameter values for an analytical corrosion model that can be used in performance assessments of specific disposal sites.

  12. A generalized correlation of experimental flat-plate collector performance. [solar collectors, performance tests, energy policy

    NASA Technical Reports Server (NTRS)

    Simon, F. F.; Miller, D. R.

    1975-01-01

    A generalized collector performance correlation was derived and shown by experimental verification to be of the proper form to account for the majority of the variable conditions encountered both in outdoor and in indoor collector tests. This correlation permits a determination of collector parameters which are essentially nonvarying under conditions which do vary randomly (outdoors) or conditions which vary in a controlled manner (indoors - simulator). It was shown that correlation of the experimental performance of collectors allows the following: (1) comparisons of different collector designs; (2) collector performance prediction under conditions that differ from the conditions of the test program; and (3) monitoring performance degradation effects.

  13. GROUND-WATER MODEL TESTING: SYSTEMATIC EVALUATION AND TESTING OF CODE FUNCTIONALITY AND PERFORMANCE

    EPA Science Inventory

    Effective use of ground-water simulation codes as management decision tools requires the establishment of their functionality, performance characteristics, and applicability to the problem at hand. This is accomplished through application of a systematic code-testing protocol and...

  14. Static performance tests of a flight-type STOVL ejector

    NASA Technical Reports Server (NTRS)

    Barankiewicz, Wendy S.

    1991-01-01

    The design and development of thrust augmenting STOVL ejectors has typically been based on experimental iteration (i.e., trial and error). Static performance tests of a full scale vertical lift ejector were performed at primary flow temperatures up to 1560 R (1100 F). Flow visualization (smoke generators and yarn tufts) were used to view the inlet air flow, especially around the primary nozzle and end plates. Performance calculations are presented for ambient temperatures close to 480 R (20 F) and 535 R (75 F) which simulate seasonal aircraft operating conditions. Resulting thrust augmentation ratios are presented as functions of nozzle pressure ratio and temperature.

  15. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  16. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  17. 16 CFR 1631.32 - Reasonable and representative tests and recordkeeping requirements-additional requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT REGULATIONS STANDARD FOR THE SURFACE FLAMMABILITY OF SMALL CARPETS AND RUGS (FF 2-70) Rules and Regulations § 1631.32 Reasonable and representative tests...

  18. Astronaut Richard Linnehan, mission specialist, performs a test on his leg using the Torque Velocity

    NASA Technical Reports Server (NTRS)

    1996-01-01

    STS-78 ONBOARD VIEW --- Astronaut Richard Linnehan, mission specialist, performs a test on his leg using the Torque Velocity Dynamometer (TVD). Dr. Thirsk was measuring changes in muscle forces of the leg in this particular view. The TVD hardware is also used to measure arm muscle forces and velocity at the bicep and tricep areas. Crew members for the mission performed all experiment protocols prior to flight to develop a baseline and will also perform post-flight tests to complete the analysis. Additionally, muscle biopsies were taken before the flight and will be conducted after the flight.

  19. Payload specialist Robert B. Thirsk, representing the Canadian Space Agency (CSA), performs a test

    NASA Technical Reports Server (NTRS)

    1996-01-01

    STS-78 ONBOARD VIEW --- Payload specialist Robert B. Thirsk, representing the Canadian Space Agency (CSA), performs a test on his arm using the Torque Velocity Dynamometer (TVD). Dr. Thirsk was measuring changes in muscle forces of the bicep and tricep in this particular view. The TVD hardware is also used to measure leg muscle forces and velocity at the ankle and elbow joints. Crew members for the mission performed all experiment protocols prior to flight to develop a baseline and will also perform post-flight tests to complete the analysis. Additionally, muscle biopsies were taken before the flight and will be conducted after the flight.

  20. GPM Avionics Module Heat Pipes Design and Performance Test Results

    NASA Technical Reports Server (NTRS)

    Ottenstein, Laura; DeChristopher, Mike

    2011-01-01

    The Global Precipitation Measurement (GPM) mission is an international network of satellites that provide the next-generation global observations of rain and snow. The GPM core satellite carries an advanced radar / radiometer system to measure precipitation from space and serve as a reference standard to unify precipitation measurements from a constellation of research and operational satellites. Through improved measurements of precipitation globally, the GPM mission will help to advance our understanding of Earth's water and energy cycle, improve forecasting of extreme events that cause natural hazards and disasters, and extend current capabilities in using accurate and timely information of precipitation to directly benefit society. The avionics module on the core satellite contains a number of electronics boxes which are cooled by a network of aluminum/ammonia heat pipes and a honeycomb radiator which contains thirteen embedded aluminum/ammonia heat pipes. All heat pipes were individually tested by the vendor (Advanced Cooling Technologies, Inc.) prior to delivery. Following delivery to NASA, the flight avionics radiator and the flight spare transport heat pipes were mounted to flight-like test structure and a system level thermal vacuum test was performed. This test, which used simulators in place of all electronics boxes, was done to verify the operation of the thermal control system as a whole. This presentation will discuss the design of the avionics module heat pipes, and then discuss performance tests results for the individual heat pipes prior to delivery and for the system level thermal vacuum test. All heat pipes met their performance requirements. However, it was found that the power was too low in some instances to start all of the smaller radiator spreader heat pipes when they were tested in a reflux configuration (which is the nominal test configuration). Although this lowered the efficiency of the radiator somewhat, it did not impact the operating