Science.gov

Sample records for adequate quality control

  1. Achieving adequate BMP`s for stormwater quality management

    SciTech Connect

    Jones-Lee, A.; Lee, G.F.

    1994-12-31

    There is considerable controversy about the technical appropriateness and the cost-effectiveness of requiring cities to control contaminants in urban stormwater discharges to meet state water quality standards equivalent to US EPA numeric chemical water quality criteria. At this time and likely for the next 10 years, urban stormwater discharges will be exempt from regulation to achieve state water quality standards in receiving waters, owing to the high cost to cities of the management of contaminants in the stormwater runoff-discharge so as to prevent exceedances of water quality standards in the receiving waters. Instead of requiring the same degree of contaminant control for stormwater discharges as is required for point-source discharges of municipal and industrial wastewaters, those responsible for urban stormwater discharges will have to implement Best Management Practices (BMP`s) for contaminant control. The recommended approach for implementation of BMP`s involves the use of site-specific evaluations of what, if any, real problems (use impairment) are caused by stormwater-associated contaminants in the waters receiving that stormwater discharge. From this type of information BMP`s can then be developed to control those contaminants in stormwater discharges that are, in fact, impairing the beneficial uses of receiving waters.

  2. Looking for an adequate quality criterion for depth coding

    NASA Astrophysics Data System (ADS)

    Kerbiriou, Paul; Boisson, Guillaume

    2010-02-01

    This paper deals with 3DTV, more especially with 3D content transmission using disparity-based format. In 3DTV, the problem of measuring the stereoscopic quality of a 3D content remains open. Depth signal degradations due to 3DTV transmission will induce new types of artifacts in the final rendered views. Whereas we have some experience regarding the issue of texture coding, the issue of depth coding consequences is rather unknown. In this paper we focus on that particular issue. For that purpose we considered LDV contents (Layered Depth Video) and performed various encoding of their depth information - i.e. depth maps plus depth occlusions layers - using MPEG-4 Part 10 AVC/H.264 MVC. We investigate the impact of depth coding artifacts on the quality of the final views. To this end, we compute the correlation between depth coding errors with the quality of the synthesized views. The criteria used for synthesized views include MSE and structural criteria such as SSIM. The criteria used for depth maps include also a topological measure in the 3D space (the Hausdorff distance). Correlations between the two criteria sets are presented. Trends in function of quantization are also discussed.

  3. Percentage of Adults with High Blood Pressure Whose Hypertension Is Adequately Controlled

    MedlinePlus

    ... is Adequately Controlled Percentage of Adults with High Blood Pressure Whose Hypertension is Adequately Controlled Heart disease ... Survey. Age Group Percentage of People with High Blood Pressure that is Controlled by Age Group f94q- ...

  4. 21 CFR 514.117 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... production performance, or biased observation. One or more adequate and well-controlled studies are required... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Adequate and well-controlled studies. 514.117... Applications § 514.117 Adequate and well-controlled studies. (a) Purpose. The primary purpose of...

  5. 21 CFR 514.117 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... production performance, or biased observation. One or more adequate and well-controlled studies are required... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Adequate and well-controlled studies. 514.117... Applications § 514.117 Adequate and well-controlled studies. (a) Purpose. The primary purpose of...

  6. 21 CFR 514.117 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... production performance, or biased observation. One or more adequate and well-controlled studies are required... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Adequate and well-controlled studies. 514.117... Applications § 514.117 Adequate and well-controlled studies. (a) Purpose. The primary purpose of...

  7. 21 CFR 514.117 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... production performance, or biased observation. One or more adequate and well-controlled studies are required... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Adequate and well-controlled studies. 514.117... Applications § 514.117 Adequate and well-controlled studies. (a) Purpose. The primary purpose of...

  8. 21 CFR 514.117 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... production performance, or biased observation. One or more adequate and well-controlled studies are required... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Adequate and well-controlled studies. 514.117... Applications § 514.117 Adequate and well-controlled studies. (a) Purpose. The primary purpose of...

  9. 21 CFR 314.126 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...-evident (general anesthetics, drug metabolism). (3) The method of selection of subjects provides adequate... respect to pertinent variables such as age, sex, severity of disease, duration of disease, and use of... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Adequate and well-controlled studies....

  10. Percentage of Adults with High Cholesterol Whose LDL Cholesterol Levels Are Adequately Controlled

    MedlinePlus

    ... of Adults with High Cholesterol Whose LDL Cholesterol Levels are Adequately Controlled High cholesterol can double a ... with High Cholesterol that is Controlled by Education Level 8k4c-k22f Download these data » Click on legends ...

  11. 21 CFR 314.126 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... conducting clinical investigations of a drug is to distinguish the effect of a drug from other influences... recognized by the scientific community as the essentials of an adequate and well-controlled clinical... randomization and blinding of patients or investigators, or both. If the intent of the trial is to...

  12. 40 CFR 141.522 - How does the State determine whether my system's watershed control requirements are adequate?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... my system's watershed control requirements are adequate? 141.522 Section 141.522 Protection of... Additional Watershed Control Requirements for Unfiltered Systems § 141.522 How does the State determine whether my system's watershed control requirements are adequate? During an onsite inspection...

  13. 40 CFR 141.522 - How does the State determine whether my system's watershed control requirements are adequate?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... my system's watershed control requirements are adequate? 141.522 Section 141.522 Protection of... Additional Watershed Control Requirements for Unfiltered Systems § 141.522 How does the State determine whether my system's watershed control requirements are adequate? During an onsite inspection...

  14. 40 CFR 141.522 - How does the State determine whether my system's watershed control requirements are adequate?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... my system's watershed control requirements are adequate? 141.522 Section 141.522 Protection of... Additional Watershed Control Requirements for Unfiltered Systems § 141.522 How does the State determine whether my system's watershed control requirements are adequate? During an onsite inspection...

  15. 40 CFR 141.522 - How does the State determine whether my system's watershed control requirements are adequate?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... my system's watershed control requirements are adequate? 141.522 Section 141.522 Protection of... Additional Watershed Control Requirements for Unfiltered Systems § 141.522 How does the State determine whether my system's watershed control requirements are adequate? During an onsite inspection...

  16. 40 CFR 141.522 - How does the State determine whether my system's watershed control requirements are adequate?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... my system's watershed control requirements are adequate? 141.522 Section 141.522 Protection of... Additional Watershed Control Requirements for Unfiltered Systems § 141.522 How does the State determine whether my system's watershed control requirements are adequate? During an onsite inspection...

  17. Esmolol in a case of severe tetanus. Adequate haemodynamic control achieved despite markedly elevated catecholamine levels.

    PubMed

    Beards, S C; Lipman, J; Bothma, P A; Joynt, G M

    1994-03-01

    A patient with severe tetanus, who had a sympathetic crisis while sedated with 30 mg/h diazepam and 30 mg/h morphine, is described. Satisfactory control of the haemodynamic crisis was achieved with bolus doses of esmolol to a total of 180 mg. A disturbing finding was that although there was adequate control of the tachycardia and hypertension, arterial catecholamine levels remained markedly elevated. Adrenaline levels of 531 pg/ml (normal 10-110 pg/ml) and noradrenaline levels of 1,036 pg/ml (normal 100-500 pg/ml) were recorded when the patient had a systolic arterial pressure of 110 mmHg and a heart rate of 97/min. The implications of this finding are discussed. PMID:11218441

  18. 30 CFR 74.6 - Quality control.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA...

  19. 30 CFR 74.6 - Quality control.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality control. 74.6 Section 74.6 Mineral... control. The applicant shall describe the way in which each lot of components will be sampled and tested... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA...

  20. 30 CFR 74.6 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control. 74.6 Section 74.6 Mineral... of the CMDPSU will be maintained in production through adequate quality control procedures, MSHA and... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6...

  1. Quality Leadership and Quality Control

    PubMed Central

    Badrick, Tony

    2003-01-01

    Different quality control rules detect different analytical errors with varying levels of efficiency depending on the type of error present, its prevalence and the number of observations. The efficiency of a rule can be gauged by inspection of a power function graph. Control rules are only part of a process and not an end in itself; just as important are the trouble-shooting systems employed when a failure occurs. 'Average of patient normals' may develop as a usual adjunct to conventional quality control serum based programmes. Acceptable error can be based on various criteria; biological variation is probably the most sensible. Once determined, acceptable error can be used as limits in quality control rule systems. A key aspect of an organisation is leadership, which links the various components of the quality system. Leadership is difficult to characterise but its key aspects include trust, setting an example, developing staff and critically setting the vision for the organisation. Organisations also have internal characteristics such as the degree of formalisation, centralisation, and complexity. Medical organisations can have internal tensions because of the dichotomy between the bureaucratic and the shadow medical structures. PMID:18568046

  2. Diet quality of Italian yogurt consumers: an application of the probability of adequate nutrient intake score (PANDiet).

    PubMed

    Mistura, Lorenza; D'Addezio, Laura; Sette, Stefania; Piccinelli, Raffaela; Turrini, Aida

    2016-01-01

    The diet quality in yogurt consumers and non-consumers was evaluated by applying the probability of adequate nutrient intake (PANDiet) index to a sample of adults and elderly from the Italian food consumption survey INRAN SCAI 2005-06. Overall, yogurt consumers had a significantly higher mean intake of energy, calcium and percentage of energy from total sugars whereas the mean percentage of energy from total fat, saturated fatty acid and total carbohydrate were significantly (p < 0.01) lower than in non-consumers. The PANDiet index was significantly higher in yogurt consumers than in non-consumers, (60.58 ± 0.33 vs. 58.58 ± 0.19, p < 0.001). The adequacy sub-score for 17 nutrients for which usual intake should be above the reference value was significantly higher among yogurt consumers. The items of calcium, potassium and riboflavin showed the major percentage variation between consumers and non-consumers. Yogurt consumers were more likely to have adequate intakes of vitamins and minerals, and a higher quality score of the diet. PMID:26906103

  3. QUALITY CONTROLS FOR PCR

    EPA Science Inventory

    The purpose of this presentation is to present an overview of the quality control (QC) sections of a draft EPA document entitled, "Quality Assurance/Quality Control Guidance for Laboratories Performing PCR Analyses on Environmental Samples." This document has been prepared by th...

  4. [Quality control dose calibrators].

    PubMed

    Montoza Aguado, M; Delgado García, A; Ramírez Navarro, A; Salgado García, C; Muros de Fuentes, M A; Ortega Lozano, S; Bellón Guardia, M E; Llamas Elvira, J M

    2004-01-01

    We have reviewed the legislation about the quality control of dose calibrator. The importance of verifying the correct work of these instruments, is fundamental in daily practice of radiopharmacy and nuclear medicine. The Spanish legislation establishes to include these controls as part of the quality control of radiopharmaceuticals, and the program of quality assurance in nuclear medicine. We have reviewed guides and protocols from international eminent organizations, summarizing the recommended tests and periodicity of them. PMID:15625064

  5. 21 CFR 314.126 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., such as spontaneous change in the course of the disease, placebo effect, or biased observation. The... control are recognized: (i) Placebo concurrent control. The test drug is compared with an inactive preparation designed to resemble the test drug as far as possible. A placebo-controlled study may...

  6. 21 CFR 314.126 - Adequate and well-controlled studies.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ..., such as spontaneous change in the course of the disease, placebo effect, or biased observation. The... control are recognized: (i) Placebo concurrent control. The test drug is compared with an inactive preparation designed to resemble the test drug as far as possible. A placebo-controlled study may...

  7. Glycemic penalty index for adequately assessing and comparing different blood glucose control algorithms

    PubMed Central

    Van Herpe, Tom; De Brabanter, Jos; Beullens, Martine; De Moor, Bart; Van den Berghe, Greet

    2008-01-01

    Introduction Blood glucose (BG) control performed by intensive care unit (ICU) nurses is becoming standard practice for critically ill patients. New (semi-automated) 'BG control' algorithms (or 'insulin titration' algorithms) are under development, but these require stringent validation before they can replace the currently used algorithms. Existing methods for objectively comparing different insulin titration algorithms show weaknesses. In the current study, a new approach for appropriately assessing the adequacy of different algorithms is proposed. Methods Two ICU patient populations (with different baseline characteristics) were studied, both treated with a similar 'nurse-driven' insulin titration algorithm targeting BG levels of 80 to 110 mg/dl. A new method for objectively evaluating BG deviations from normoglycemia was founded on a smooth penalty function. Next, the performance of this new evaluation tool was compared with the current standard assessment methods, on an individual as well as a population basis. Finally, the impact of four selected parameters (the average BG sampling frequency, the duration of algorithm application, the severity of disease, and the type of illness) on the performance of an insulin titration algorithm was determined by multiple regression analysis. Results The glycemic penalty index (GPI) was proposed as a tool for assessing the overall glycemic control behavior in ICU patients. The GPI of a patient is the average of all penalties that are individually assigned to each measured BG value based on the optimized smooth penalty function. The computation of this index returns a number between 0 (no penalty) and 100 (the highest penalty). For some patients, the assessment of the BG control behavior using the traditional standard evaluation methods was different from the evaluation with GPI. Two parameters were found to have a significant impact on GPI: the BG sampling frequency and the duration of algorithm application. A higher BG

  8. Computers and quality control in nuclear medicine.

    PubMed

    Brookeman, V A

    1978-04-01

    The general topic of computers and nuclear medicine quality control may be approached from two main areas; controlling the quality of computerized studies, and computer applications in general nuclear medicine quality control. Overlap occurs when quality control of computer studies is performed by the computer itself. The uses of computers in record-keeping and in quality control of imaging instrumentation and in vitro studies, including radioimmunoassay, are discussed in this review. Aspects of quality control for computerized clinical cardiovascular, cerebral, and renal studies and emission computed tomography are reviewed, including consideration of difficulties and inaccuracies involved in the studies. Any automatic computer analysis program should incorporate adequate checks and error detection protocols and should illustrate results for verification. Current routine quality control procedures using the computer unfortunately are few. Quality control criteria are needed for camera/computer systems in high count rate clinical applications, and increasing emphasis should be aimed at quality control of those computerized dynamic and function studies in current clinical use. The computer has a valuable potential for nuclear medicine quality control. In vitro and computerized in vivo studies can be analyzed by readily available statistical programs, and variances can be monitored continuously. Computers can calibrate and monitor instrument performance regularly, and can handle managerial and clerical duties such as bookkeeping. PMID:684439

  9. Instrument Quality Control.

    PubMed

    Jayakody, Chatura; Hull-Ryde, Emily A

    2016-01-01

    Well-defined quality control (QC) processes are used to determine whether a certain procedure or action conforms to a widely accepted standard and/or set of guidelines, and are important components of any laboratory quality assurance program (Popa-Burke et al., J Biomol Screen 14: 1017-1030, 2009). In this chapter, we describe QC procedures useful for monitoring the accuracy and precision of laboratory instrumentation, most notably automated liquid dispensers. Two techniques, gravimetric QC and photometric QC, are highlighted in this chapter. When used together, these simple techniques provide a robust process for evaluating liquid handler accuracy and precision, and critically underpin high-quality research programs. PMID:27316990

  10. Japanese Quality Control Circles.

    ERIC Educational Resources Information Center

    Nishiyama, Kazuo

    In recent years, United States scholars with an interest in international business and organizational communication have begun to notice the success of Japanese "quality control circles." These are small groups, usually composed of seven to ten workers, who are organized at the production levels within most large Japanese factories. A typical…

  11. SIMBAD Quality-Control

    NASA Astrophysics Data System (ADS)

    Lesteven, Soizick

    1993-01-01

    Taking into consideration the amount and the complexity of SIMBAD data, it is necessary to use automatic methods to control and assure the quality of the SIMBAD database. One possibility is to apply multivariate data analysis to the content of documents related to astronomical data. The method and first results are presented.

  12. [Comparing quality measurements Part 2: control charts].

    PubMed

    Kottner, Jan; Hauss, Armin

    2013-04-01

    Comparative quality measurements and evaluations in nursing play significant roles. Quality measures are affected by systematic and random error. Statistical Process Control (SPC) offers a method to take random variation adequately into account. In this article, control charts are introduced. Those are graphical displays to show quality measures over time. Attribute variables can be displayed by p-, u- and c-control charts. Special cause variations within the processes can be detected by rules. If signs for special cause variations are absent, the process in considered being in statistical control showing common cause variation. A deviation of one data point greater than three standard deviations from the arithmetic mean is considered the strongest signal for non random variation within the process. Within quality improvement contexts control charts outperform traditional comparisons of means and spreads. PMID:23535476

  13. Vgi Quality Control

    NASA Astrophysics Data System (ADS)

    Fonte, C. C.; Bastin, L.; Foody, G.; Kellenberger, T.; Kerle, N.; Mooney, P.; Olteanu-Raimond, A.-M.; See, L.

    2015-08-01

    This paper presents a framework for considering quality control of volunteered geographic information (VGI). Different issues need to be considered during the conception, acquisition and post-acquisition phases of VGI creation. This includes items such as collecting metadata on the volunteer, providing suitable training, giving corrective feedback during the mapping process and use of control data, among others. Two examples of VGI data collection are then considered with respect to this quality control framework, i.e. VGI data collection by National Mapping Agencies and by the most recent Geo-Wiki tool, a game called Cropland Capture. Although good practices are beginning to emerge, there is still the need for the development and sharing of best practice, especially if VGI is to be integrated with authoritative map products or used for calibration and/or validation of land cover in the future.

  14. Quality control review: implementing a scientifically based quality control system.

    PubMed

    Westgard, James O; Westgard, Sten A

    2016-01-01

    This review focuses on statistical quality control in the context of a quality management system. It describes the use of a 'Sigma-metric' for validating the performance of a new examination procedure, developing a total quality control strategy, selecting a statistical quality control procedure and monitoring ongoing quality on the sigma scale. Acceptable method performance is a prerequisite to the design and implementation of statistical quality control procedures. Statistical quality control can only monitor performance, and when properly designed, alert analysts to the presence of additional errors that occur because of unstable performance. A new statistical quality control planning tool, called 'Westgard Sigma Rules,' provides a simple and quick way for selecting control rules and the number of control measurements needed to detect medically important errors. The concept of a quality control plan is described, along with alternative adaptations of a total quality control plan and a risk-based individualized quality control plan. Finally, the ongoing monitoring of analytic performance and test quality are discussed, including determination of measurement uncertainty from statistical quality control data collected under intermediate precision conditions and bias determined from proficiency testing/external quality assessment surveys. A new graphical tool, called the Sigma Quality Assessment Chart, is recommended for demonstrating the quality of current examination procedures on the sigma scale. PMID:26150675

  15. 42 CFR 84.41 - Quality control plans; contents.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... management of quality, including: (1) Requirements for the production of quality data and the use of quality... accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from DODSSP, Standardization..., manufacturing, and fabrication, inspections are adequate to ensure control of finished article...

  16. 42 CFR 84.41 - Quality control plans; contents.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... management of quality, including: (1) Requirements for the production of quality data and the use of quality... accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from DODSSP, Standardization..., manufacturing, and fabrication, inspections are adequate to ensure control of finished article...

  17. 42 CFR 84.41 - Quality control plans; contents.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... management of quality, including: (1) Requirements for the production of quality data and the use of quality... accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from DODSSP, Standardization..., manufacturing, and fabrication, inspections are adequate to ensure control of finished article...

  18. 42 CFR 84.41 - Quality control plans; contents.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... management of quality, including: (1) Requirements for the production of quality data and the use of quality... accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from DODSSP, Standardization..., manufacturing, and fabrication, inspections are adequate to ensure control of finished article...

  19. Telotristat etiprate, a novel serotonin synthesis inhibitor, in patients with carcinoid syndrome and diarrhea not adequately controlled by octreotide.

    PubMed

    Kulke, Matthew H; O'Dorisio, Thomas; Phan, Alexandria; Bergsland, Emily; Law, Linda; Banks, Phillip; Freiman, Joel; Frazier, Kenny; Jackson, Jessica; Yao, James C; Kvols, Larry; Lapuerta, Pablo; Zambrowicz, Brian; Fleming, Douglas; Sands, Arthur

    2014-10-01

    Serotonin produced by neuroendocrine tumors is believed to be a principal cause of the diarrhea in carcinoid syndrome. We assessed the safety and efficacy of telotristat etiprate, an oral serotonin synthesis inhibitor, in patients with diarrhea associated with carcinoid syndrome. In this prospective, randomized study, patients with evidence of carcinoid tumor and ≥4 bowel movements (BMs)/day despite stable-dose octreotide LAR depot therapy were enrolled in sequential, escalating, cohorts of four patients per cohort. In each cohort, one patient was randomly assigned to placebo and three patients to telotristat etiprate, at 150, 250, 350, or 500 mg three times a day (tid). In a subsequent cohort, one patient was assigned to placebo and six patients to telotristat etiprate 500 mg tid. Patients were assessed for safety, BM frequency (daily diary), 24 h urinary 5-hydroxyindoleacetic acid (u5-HIAA), and adequate relief of carcinoid gastrointestinal symptoms (using a weekly questionnaire). Twenty-three patients were treated: 18 received telotristat etiprate and five received placebo. Adverse events were generally mild. Among evaluable telotristat etiprate-treated patients, 5/18 (28%) experienced a ≥30% reduction in BM frequency for ≥2 weeks, 9/16 (56%) experienced biochemical response (≥50% reduction or normalization in 24-h u5-HIAA) at week 2 or 4, and 10/18 (56%) reported adequate relief during at least 1 of the first 4 weeks of treatment. Similar activity was not observed in placebo-treated patients. Telotristat etiprate was well tolerated. Our observations suggest that telotristat etiprate has activity in controlling diarrhea associated with carcinoid syndrome. Further studies confirming these findings are warranted. PMID:25012985

  20. Telotristat Etiprate, a Novel Serotonin Synthesis Inhibitor, in Patients with Carcinoid Syndrome and Diarrhea Not Adequately Controlled by Octreotide

    PubMed Central

    Kulke, Matthew H.; O’Dorisio, Thomas; Phan, Alexandria; Bergsland, Emily; Law, Linda; Banks, Phillip; Freiman, Joel; Frazier, Kenny; Jackson, Jessica; Yao, James C.; Kvols, Larry; Lapuerta, Pablo; Zambrowicz, Brian; Fleming, Douglas; Sands, Arthur

    2014-01-01

    Serotonin produced by neuroendocrine tumors is believed to be a principal cause of the diarrhea in carcinoid syndrome. We assessed the safety and efficacy of telotristat etiprate, an oral serotonin synthesis inhibitor, in patients with diarrhea associated with carcinoid syndrome. In this prospective, randomized study, patients with evidence of carcinoid tumor and ≥4 bowel movements (BMs)/day despite stable-dose octreotide LAR depot therapy were enrolled in sequential, escalating, cohorts of 4 patients/cohort. In each cohort, 1 patient was randomly assigned to placebo and 3 patients to telotristat etiprate, at 150, 250, 350, or 500 mg 3x/day (tid). In a subsequent cohort, 1 patient was assigned to placebo and 6 patients to telotristat etiprate 500 mg tid. Patients were assessed for safety, BM frequency (daily diary), 24-hour urinary 5-hydroxyindoleacetic acid (u5-HIAA), and adequate relief of carcinoid gastrointestinal symptoms (using a weekly questionnaire). Twenty-three patients were treated; 18 received telotristat etiprate and 5 received placebo. Adverse events were generally mild. Among evaluable telotristat etiprate-treated patients, 5/18 (28%) experienced a ≥30% reduction in BM frequency for ≥2 weeks, 9/16 (56%) experienced biochemical response (≥50% reduction or normalization in 24-hour u5-HIAA) at Week 2 or 4, and 10/18 (56%) reported adequate relief during at least 1 of the first 4 weeks of treatment. Similar activity was not observed in placebo-treated patients. Telotristat etiprate was well tolerated. Our observations suggest that telotristat etiprate has activity in controlling diarrhea associated with carcinoid syndrome. Further studies confirming these findings are warranted. PMID:25012985

  1. Radiographic quality control devices.

    PubMed

    2000-04-01

    In this study, we evaluate eight radiographic quality control (QC) devices, which noninvasively measure the output from a variety of diagnostic x-ray production systems. When used as part of a quality assurance (QA) program, radiographic QC devices help ensure that x-ray equipment is working within acceptable limits. This in turn helps ensure that high-quality images are achieved with appropriate radiation doses and that resources are used efficiently (for example, by minimizing the number of repeat exposures required). Our testing focused on the physical performance, ease of use, and service and maintenance characteristics that affect the use of these devices for periodic, routine measurements of x-ray system parameters. We found that all the evaluated models satisfactorily measure all the parameters normally needed for a QA program. However, we did identify a number of differences among the models--particularly in the range of exposure levels that can be effectively measured and the ease of use. Three models perform well for a variety of applications and are very easy to use; we rate them Preferred. Three additional models have minor limitations but otherwise perform well; we rate them Acceptable. We recommend against purchasing two models because, although each performs acceptably for most applications, neither model can measure low levels of radiation. This Evaluation covers devices designed to measure the output of x-ray tubes noninvasively. These devices, called radiographic quality control (QC) devices, or QC meters, are typically used by medical physicists, x-ray engineers, biomedical engineers, and suitably trained radiographic technologists to make QC measurements. We focus on the use of these devices as part of an overall quality assurance (QA) program. We have not evaluated their use for other applications, such as acceptance testing. To be included in this study, a device must be able to measure the exposure- and kVp-related characteristics of most x

  2. Are the defined substrate-based methods adequate to determine the microbiological quality of natural recreational waters?

    PubMed

    Valente, Marta Sofia; Pedro, Paulo; Alonso, M Carmen; Borrego, Juan J; Dionísio, Lídia

    2010-03-01

    Monitoring the microbiological quality of water used for recreational activities is very important to human public health. Although the sanitary quality of recreational marine waters could be evaluated by standard methods, they are time-consuming and need confirmation. For these reasons, faster and more sensitive methods, such as the defined substrate-based technology, have been developed. In the present work, we have compared the standard method of membrane filtration using Tergitol-TTC agar for total coliforms and Escherichia coli, and Slanetz and Bartley agar for enterococci, and the IDEXX defined substrate technology for these faecal pollution indicators to determine the microbiological quality of natural recreational waters. ISO 17994:2004 standard was used to compare these methods. The IDEXX for total coliforms and E. coli, Colilert, showed higher values than those obtained by the standard method. Enterolert test, for the enumeration of enterococci, showed lower values when compared with the standard method. It may be concluded that more studies to evaluate the precision and accuracy of the rapid tests are required in order to apply them for routine monitoring of marine and freshwater recreational bathing areas. The main advantages of these methods are that they are more specific, feasible and simpler than the standard methodology. PMID:20009243

  3. SIMBAD quality-control

    NASA Technical Reports Server (NTRS)

    Lesteven, Soizick

    1992-01-01

    The astronomical database SIMBAD developed at the Centre de donnees astronomiques de Strasbourg presently contains 760,000 objects (stellar and non-stellar). It has the unique characteristic of being structured specifically for astronomical objects. All types of heterogeneous data (bibliographic references, measurements, and sets of identification) are connected with each object. The attributes that define quality of the database include the following. Reliability: cross-identification should not rely upon just exact values object coordinates. It also means that information attached to one simple object should be consistent. The existing data must be controlled in order to start with a reliable base and to cross-identify new data assuring the quality as data grows. Exhaustivity: delays between publication of new informations and their inclusion in the database should be as short as possible. The integrity of the database has to be maintained as data accumulates. Taking the amount of data into consideration and the rate of new data production, it is necessary to use automatic methods. One of the possibilities is to use multivariate data analysis. The factor-space is a n-dimensional relevancy space which is described by the n-axes representing a set of n subject matter headings; the words and phrases can be used to scale the axes and the documents are then a vector average of the terms within them. The application reported herein is based on the NASA-STI bibliographical database. The selected data concern astronomy, astrophysics, and space radiation (102,963 references from 1975 to 1991 included 8070 keywords). The F-space is built from this bibliographical data. By comparing the F-space position obtained from the NASA-STI keywords with the F-space position obtained from the SIMBAD references, the authors will be able to show whether it is possible to retrieve information with a restricted set of words only. If the comparison is valid, this will be a way to enter

  4. General aviation fuel quality control

    NASA Technical Reports Server (NTRS)

    Poitz, H.

    1983-01-01

    Quality control measures for aviation gasoline, and some of the differences between quality control on avgas and mogas are discussed. One thing to keep in mind is that with motor gasoline you can always pull off to the side of the road. It's not so easy to do in an airplane. Consequently, there are reasons for having the tight specifications and the tight quality control measures on avgas as compared to motor gasoline.

  5. Quality control on the frontier

    PubMed Central

    Paszkiewicz, Konrad H.; Farbos, Audrey; O'Neill, Paul; Moore, Karen

    2014-01-01

    In the world of high-throughput sequencing there are numerous challenges to effective data quality control. There are no single quality metrics which are appropriate in all conditions. Here we detail the different open source software used at the Exeter Sequencing Service to provide generic quality control information, as well as more specific metrics for genomic and transcriptomic libraries run on Illumina platforms. PMID:24904650

  6. Quality assurance/quality control manual; National Water Quality Laboratory

    USGS Publications Warehouse

    Pritt, J.W.; Raese, J.W.

    1995-01-01

    Quality-control practices are established for the operation of the U.S. Geological Survey's National Water Quality Laboratory. These practices specify how samples are preserved, shipped, and analyzed in the Laboratory. This manual documents the practices that are currently (1995) used in the Laboratory.

  7. Combination and triple therapy in patients with stable angina pectoris not adequately controlled by optimal β-blocker therapy

    PubMed Central

    Kok, W.E.M.; Visser, F.C.; Visser, C.A.

    2002-01-01

    In 60 to 80% of patients with stable angina pectoris at low risk for future coronary events, monotherapy with a β-blocker is an effective treatment. When patients with stable angina pectoris and low risk for events do not respond adequately to optimal β-blocker monotherapy, combination therapy or even triple therapy is may be recommended, but little is known of the actual benefit of such a strategy. We reviewed the evidence from the literature on the effectiveness of combination and triple therapy. Combination therapy with a calcium antagonist or nitrate was found to be more effective than β-blocker monotherapy in the majority of studies, but only an estimated 30% of patients objectively benefit from these combination therapies. Direct comparison shows that combination therapy of a β-blocker with a calcium antagonist is more effective than the combination of a β-blocker with a nitrate. An inadequate response to β-blocker monotherapy is more effectively improved by addition of a calcium antagonist than by alternative use of a calcium antagonist. The use of triple therapy is controversial and not recommended in patients with mild angina pectoris, while for patients with severe angina pectoris not responding to combination therapy of a β-blocker with a nitrate, triple therapy may be of advantage, although the number of patients studied has been small. PMID:25696045

  8. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Quality assurance and quality control. 26.167 Section 26... Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance program. Each HHS-certified laboratory shall have a quality assurance program that encompasses all...

  9. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Quality assurance and quality control. 26.137 Section 26....137 Quality assurance and quality control. (a) Quality assurance program. Each licensee testing facility shall have a quality assurance program that encompasses all aspects of the testing...

  10. Essential elements of quality control.

    PubMed

    Boylan, J C

    1983-11-01

    The components of quality control in the pharmaceutical industry are discussed as they apply to hospital pharmacy admixture services. The pharmaceutical industry complies with the FDA's Current Good Manufacturing Practices, which require manufacturers to have written procedures for ensuring sterility and nonpyrogenicity of injectable products. Because FDA specifies only what outcome measures must be assessed (rather than specific means of assessment), pharmaceutical companies have developed a multiplicity of quality-control systems. However, each system consists of a master formula (quantitative listing of all ingredients), master manufacturing instructions (the recipe for each product), master packaging instructions, and batch records. Documents used by quality control personnel include the specifications (identification, tests, and limits for products), test methods, and sampling procedures. Hospitals should have similar quality-control programs. These programs should systematically prevent or identify and correct deficiencies, measure overall quality, and provide information for managers. Hospital pharmacists whose departments do not have comprehensive programs should consult colleagues who have developed such procedures. Techniques used in industry should be applied when possible. To protect the integrity of manufacturers' drug products during compounding in hospitals, every hospital admixture service must have its own quality-control system. PMID:6650523

  11. Principles and Practices for Quality Assurance and Quality Control

    USGS Publications Warehouse

    Jones, Berwyn E.

    1999-01-01

    Quality assurance and quality control are vital parts of highway runoff water-quality monitoring projects. To be effective, project quality assurance must address all aspects of the project, including project management responsibilities and resources, data quality objectives, sampling and analysis plans, data-collection protocols, data quality-control plans, data-assessment procedures and requirements, and project outputs. Quality control ensures that the data quality objectives are achieved as planned. The historical development and current state of the art of quality assurance and quality control concepts described in this report can be applied to evaluation of data from prior projects.

  12. Rectal cancer delivery of radiotherapy in adequate time and with adequate dose is influenced by treatment center, treatment schedule, and gender and is prognostic parameter for local control: Results of study CAO/ARO/AIO-94

    SciTech Connect

    Fietkau, Rainer . E-mail: rainer.fietkau@med.uni-rostock.de; Roedel, Claus; Hohenberger, Werner; Raab, Rudolf; Hess, Clemens; Liersch, Torsten; Becker, Heinz; Wittekind, Christian; Hutter, Matthias; Hager, Eva; Karstens, Johann; Ewald, Hermann; Christen, Norbert; Jagoditsch, Michael; Martus, Peter; Sauer, Rolf

    2007-03-15

    Purpose: The impact of the delivery of radiotherapy (RT) on treatment results in rectal cancer patients is unknown. Methods and Materials: The data from 788 patients with rectal cancer treated within the German CAO/AIO/ARO-94 phase III trial were analyzed concerning the impact of the delivery of RT (adequate RT: minimal radiation RT dose delivered, 4300 cGy for neoadjuvant RT or 4700 cGy for adjuvant RT; completion of RT in <44 days for neoadjuvant RT or <49 days for adjuvant RT) in different centers on the locoregional recurrence rate (LRR) and disease-free survival (DFS) at 5 years. The LRR, DFS, and delivery of RT were analyzed as endpoints in multivariate analysis. Results: A significant difference was found between the centers and the delivery of RT. The overall delivery of RT was a prognostic factor for the LRR (no RT, 29.6% {+-} 7.8%; inadequate RT, 21.2% {+-} 5.6%; adequate RT, 6.8% {+-} 1.4%; p = 0.0001) and DFS (no RT, 55.1% {+-} 9.1%; inadequate RT, 57.4% {+-} 6.3%; adequate RT, 69.1% {+-} 2.3%; p = 0.02). Postoperatively, delivery of RT was a prognostic factor for LRR on multivariate analysis (together with pathologic stage) but not for DFS (independent parameters, pathologic stage and age). Preoperatively, on multivariate analysis, pathologic stage, but not delivery of RT, was an independent prognostic parameter for LRR and DFS (together with adequate chemotherapy). On multivariate analysis, the treatment center, treatment schedule (neoadjuvant vs. adjuvant RT), and gender were prognostic parameters for adequate RT. Conclusion: Delivery of RT should be regarded as a prognostic factor for LRR in rectal cancer and is influenced by the treatment center, treatment schedule, and patient gender.

  13. Analytical laboratory quality control charting

    SciTech Connect

    O'Bryan, Ervin F.

    2001-06-11

    In life the importance of setting goals is stressed. The desired end result must be envisioned to chart a path and determine indicators to provide feedback on the process. Quality does not happen by accident but is achieved through a constant process of setting goals, process development, monitoring process indicators, fine tuning the process, and achieving results. These goals are to be focused and clearly measurable. In industry and life the setting of goals with clear process indicators is often difficult because of the variable end result and scarcity of measurements. Laboratories are fortunate in that they have a plethora of measurements with known or desired end results (controls) to monitor the process and give instantaneous feedback on quality. A key quality tool used by the laboratory to monitor and evaluate the lab processes is control charting. When properly utilized Quality Control (QC) Charts allow labs to be proactive in addressing problems rather than reactive. Several methods are available for control charting and some are listed in the references/information sources. The content for this paper is based on the control-charting program utilized at the Department of Energy's Fernald site. This control-charting program has specific areas of emphasis, simple charts, trend analyses, and effective follow-up.

  14. Quality control programme in mammography: second level quality controls.

    PubMed

    Nassivera, E; Nardin, L

    1997-06-01

    Mammography is the most reliable method by which to detect lesions in the breast. Since contrast between normal and pathological areas in the breast is extremely low, mammographic image quality should reach high standards without exceeding acceptable exposure levels for the breast. A quality control programme in mammography has been implemented. This programme is subdivided into two levels. The first consists of simple daily checks of image quality and film processing, while the second deals with more complex checks of mammographic unit, screen-film system, darkroom, illuminators, viewing conditions and reference dose determination. The values of all the parameters undergoing measurement are compared with the limiting values given by National and International Protocols. This paper describes the second level controls carried out every 6 months by the medical physicist. The parameters described are only those which have been studied and analysed in detail since the quality control programme in mammography was implemented. Such parameters (kilovoltage, focal spot dimension, half value layer, tube output, automatic exposure control system, screen-film characteristic curve and mean glandular dose) were measured during the period 1991-1995 and the results summarised. The values obtained prove the constant correct functioning of the equipment. PMID:9227255

  15. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Quality assurance and quality control. 26.167 Section 26.167 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Laboratories Certified by the Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance program. Each HHS-certified laboratory...

  16. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 1 2014-01-01 2014-01-01 false Quality assurance and quality control. 26.167 Section 26.167 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Laboratories Certified by the Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance program. Each HHS-certified laboratory...

  17. 10 CFR 26.167 - Quality assurance and quality control.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Quality assurance and quality control. 26.167 Section 26.167 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Laboratories Certified by the Department of Health and Human Services § 26.167 Quality assurance and quality control. (a) Quality assurance program. Each HHS-certified laboratory...

  18. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 1 2011-01-01 2011-01-01 false Quality assurance and quality control. 26.137 Section 26.137 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.137 Quality assurance and quality control. (a) Quality assurance program. Each licensee...

  19. 10 CFR 26.137 - Quality assurance and quality control.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 1 2013-01-01 2013-01-01 false Quality assurance and quality control. 26.137 Section 26.137 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.137 Quality assurance and quality control. (a) Quality assurance program. Each licensee...

  20. 40 CFR 51.359 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is... quality control frequencies by using statistical process control to monitor equipment performance on...

  1. Enhancement of Bacillus subtilis Lipopeptide Biosurfactants Production through Optimization of Medium Composition and Adequate Control of Aeration

    PubMed Central

    Ghribi, Dhouha; Ellouze-Chaabouni, Semia

    2011-01-01

    Interest in biosurfactants has increased considerably in recent years, as they are potentially used in many commercial applications in petroleum, pharmaceuticals, biomedical, and food processing industries. Since improvement of their production was of great importance to reduce the final coast, cultural conditions were analyzed to optimize biosurfactants production from Bacillus subtilis SPB1 strain. A high yield of biosurfactants was obtained from a culture of B. subtilis using carbohydrate substrate as a carbon source; among carbohydrates, glucose enhanced the best surfactin production. The optimum glucose concentration was 40 g/L. Higher amount of biosurfactants was obtained using 5 g/L of urea as organic nitrogen source and applying C/N ratio of 7 with ammonium chloride as inorganic nitrogen source. The highest amount of biosurfactants was recorded with the addition of 2% kerosene. Moreover, it was shown, using an automated full-controlled 2.6 L fermenter, that aeration of the medium, which affected strongly the growth regulated biosurfactants synthesis by the producing cell. So that, low or high aerations lead to a decrease of biosurfactants synthesis yields. It was found that when using dissolved oxygen saturation of the medium at 30%, biosurfactants production reached 4.92 g/L. PMID:21966596

  2. Quality control of EUVE databases

    NASA Technical Reports Server (NTRS)

    John, L. M.; Drake, J.

    1992-01-01

    The publicly accessible databases for the Extreme Ultraviolet Explorer include: the EUVE Archive mailserver; the CEA ftp site; the EUVE Guest Observer Mailserver; and the Astronomical Data System node. The EUVE Performance Assurance team is responsible for verifying that these public EUVE databases are working properly, and that the public availability of EUVE data contained therein does not infringe any data rights which may have been assigned. In this poster, we describe the Quality Assurance (QA) procedures we have developed from the approach of QA as a service organization, thus reflecting the overall EUVE philosophy of Quality Assurance integrated into normal operating procedures, rather than imposed as an external, post facto, control mechanism.

  3. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Quality assurance and quality control. 136.7 Section 136.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) GUIDELINES ESTABLISHING TEST PROCEDURES FOR THE ANALYSIS OF POLLUTANTS § 136.7 Quality assurance and quality control. The...

  4. 23 CFR 1340.8 - Quality control.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data...

  5. 23 CFR 1340.8 - Quality control.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data...

  6. 23 CFR 1340.8 - Quality control.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... OBSERVATIONAL SURVEYS OF SEAT BELT USE Survey Design Requirements § 1340.8 Quality control. (a) Quality control... control monitors involved in seat belt use surveys shall have received training in data...

  7. Quality Control of Meteorological Observations

    NASA Technical Reports Server (NTRS)

    Collins, William; Dee, Dick; Rukhovets, Leonid

    1999-01-01

    For the first time, a problem of the meteorological observation quality control (QC) was formulated by L.S. Gandin at the Main Geophysical Observatory in the 70's. Later in 1988 L.S. Gandin began adapting his ideas in complex quality control (CQC) to the operational environment at the National Centers for Environmental Prediction. The CQC was first applied by L.S.Gandin and his colleagues to detection and correction of errors in rawinsonde heights and temperatures using a complex of hydrostatic residuals.Later, a full complex of residuals, vertical and horizontal optimal interpolations and baseline checks were added for the checking and correction of a wide range of meteorological variables. some other of Gandin's ideas were applied and substantially developed at other meteorological centers. A new statistical QC was recently implemented in the Goddard Data Assimilation System. The central component of any quality control is a buddy check which is a test of individual suspect observations against available nearby non-suspect observations. A novel feature of this test is that the error variances which are used for QC decision are re-estimated on-line. As a result, the allowed tolerances for suspect observations can depend on local atmospheric conditions. The system is then better able to accept extreme values observed in deep cyclones, jet streams and so on. The basic statements of this adaptive buddy check are described. Some results of the on-line QC including moisture QC are presented.

  8. Efficacy and Tolerability of Telmisartan Plus Amlodipine in Asian Patients Not Adequately Controlled on Either Monotherapy or on Low-Dose Combination Therapy

    PubMed Central

    Zhu, Dingliang; Gao, Pingjin; Yagi, Nobutaka

    2014-01-01

    Objective. To evaluate the efficacy and safety of the telmisartan plus amlodipine (T/A) single-pill combination (SPC) in Asian patients with hypertension whose blood pressure (BP) was not adequately controlled on either monotherapy or on low-dose combination therapy. Patients and Methods. Data are presented from five Boehringer Ingelheim-sponsored phase 3, double-blind, 8-week, studies: two studies in nonresponders to amlodipine (data pooled for amlodipine), two studies on nonresponders to telmisartan (pooled data), and one on nonresponders to low-dose T/A SPC. Results. After 8 weeks' treatment, mean reductions from the reference baseline in diastolic BP (DBP; primary endpoint), systolic BP (SBP), and SBP, DBP goal, and response rates were higher with the T/A SPC than respective monotherapies. The T80/A5 SPC resulted in greater reductions in DBP and SBP, and higher DBP goal and response rate than the low-dose T40/A5 SPC. Peripheral edema incidence was low (amlodipine 0.5%, telmisartan 0.0%, and T/A SPC 0.7%). Discussion and Conclusion. In Asian patients whose BP is not adequately controlled with telmisartan or amlodipine monotherapy, T/A SPC treatment results in greater BP reduction, and higher DBP and SBP goal and response rates. The safety and tolerability of the T/A SPC are comparable to those of the respective monotherapies and consistent with those reported in previous studies. PMID:24719757

  9. 7 CFR 930.44 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 930.44 Section 930.44 Agriculture... MICHIGAN, NEW YORK, PENNSYLVANIA, OREGON, UTAH, WASHINGTON, AND WISCONSIN Order Regulating Handling Quality Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of...

  10. 7 CFR 981.42 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 981.42 Section 981.42 Agriculture... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this... establish, with the approval of the Secretary, such minimum quality and inspection requirements...

  11. 21 CFR 1404.900 - Adequate evidence.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Adequate evidence. 1404.900 Section 1404.900 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY GOVERNMENTWIDE DEBARMENT AND SUSPENSION (NONPROCUREMENT) Definitions § 1404.900 Adequate evidence. Adequate evidence means information sufficient to support the reasonable belief that a particular...

  12. 40 CFR 51.359 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 2 2011-07-01 2011-07-01 false Quality control. 51.359 Section 51.359....359 Quality control. Quality control measures shall insure that emission testing equipment is calibrated and maintained properly, and that inspection, calibration records, and control charts...

  13. [Quality control in clinical trials].

    PubMed

    Fukushima, M

    1996-01-01

    Quality control (QC) in clinical trials means the procedures which insure protection of human subjects from research risk, reliability of the data, and thereby assures internal consistency. This has been developed since 1970s in the US, by establishing various regulations which are now called GCP. From the viewpoint of total QC, it should be emphasized that rigorous review of protocol by the Institutional Review Board and obtaining Informed Consent are prerequisites for insuring the quality of the given trial at high scientific level. When pursuing a clinical trial, first of all, facilities of the institutions and the ability of investigators must be of high quality. For this reason, at each institution previous data related to trials should be thoroughly reviewed and analyzed prior to developing a protocol. Educational courses in QC in clinical practice are invaluable. QC of diagnosis means, for example, central pathology review and standardization of diagnostic procedures and process. Secondly, at each institution, data managers collect the data and submit them to the central office at the indicated time. In order to evolve clinical trial, continuous education for data managers and expansion of their job are encouraged. Thirdly, at the statistical center independent from the research group office, subject-specific data managers, the biostatistical staff, must check submitted forms for completeness, consistency and accuracy. Finally, at the data analysis, quality evaluation of the research should also be carried out. Throughout the trial, monitoring and audit are particularly important to assure quality. The sponsor has the responsibility of monitoring the trial and make rigorous onsite visits, and the individual study group also have a monitoring program, while the FDA and the NCI audit by themselves. The purpose of audit is not only to assure data reliability but also to check out patient compliance to drug, education as to regulations and rules of clinical

  14. Research of data quality control based on quality grading

    NASA Astrophysics Data System (ADS)

    Liu, Shuang Hong; Yu, Jian Guo; Yu, Yong Ling

    2012-01-01

    To solve the problem of data quality in data warehouse, the process of data stream in data warehouse and the factors influencing data quality were analyzed; a method for controlling data quality based on quality grading was proposed and the frame of data quality grading system was established. In each process of ETL, the data quality grading system would execute script to calculate values, such as total, component and standard measures in accordance with the definition of Unit Measure, so as to get representation indexes; and then the quality report would be generated according to the indexes and the quality would be graded. The method is applicable to various data warehouse systems.

  15. Research of data quality control based on quality grading

    NASA Astrophysics Data System (ADS)

    Liu, Shuang Hong; Yu, Jian Guo; Yu, Yong Ling

    2011-12-01

    To solve the problem of data quality in data warehouse, the process of data stream in data warehouse and the factors influencing data quality were analyzed; a method for controlling data quality based on quality grading was proposed and the frame of data quality grading system was established. In each process of ETL, the data quality grading system would execute script to calculate values, such as total, component and standard measures in accordance with the definition of Unit Measure, so as to get representation indexes; and then the quality report would be generated according to the indexes and the quality would be graded. The method is applicable to various data warehouse systems.

  16. Assessment of adequate quality and collocation of reference measurements with space-borne hyperspectral infrared instruments to validate retrievals of temperature and water vapour

    NASA Astrophysics Data System (ADS)

    Calbet, X.

    2016-01-01

    A method is presented to assess whether a given reference ground-based point observation, typically a radiosonde measurement, is adequately collocated and sufficiently representative of space-borne hyperspectral infrared instrument measurements. Once this assessment is made, the ground-based data can be used to validate and potentially calibrate, with a high degree of accuracy, the hyperspectral retrievals of temperature and water vapour.

  17. Quality control of antibodies for assay development.

    PubMed

    Schumacher, Sarah; Seitz, Harald

    2016-09-25

    Antibodies are used as powerful tools in basic research, for example, in biomarker identification, and in various forms for diagnostics, for example, identification of allergies or autoimmune diseases. Due to their robustness and ease of handling, immunoassays are favourite methods for investigation of various biological or medical questions. Nevertheless in many cases, additional analyses such as mass spectrometry are used to validate or confirm the results of immunoassays. To minimize the workload and to increase confidence in immunoassays, there are urgent needs for antibodies which are both highly specific and well validated. Unfortunately many commercially available antibodies are neither well characterized nor fully tested for cross-reactivities. Adequate quality control and validation of an antibody is time-consuming and can be frustrating. Such validation needs to be performed for every assay/application. However, where an antibody validation is successful, a highly specific and stable reagent will be on hand. This article describes the validation processes of antibodies, including some often neglected factors, as well as unspecific binding to other sample compounds in a multiparameter diagnostic assay. The validation consists of different immunological methods, with important assay controls, and is performed in relation to the development of a diagnostic test. PMID:26873787

  18. 40 CFR 51.359 - Quality control.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....359 Quality control. Quality control measures shall insure that emission testing equipment is... 40 Protection of Environment 2 2013-07-01 2013-07-01 false Quality control. 51.359 Section 51.359... of tests) which fall into the testing categories identified. Alternatives or exceptions to...

  19. 40 CFR 51.359 - Quality control.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ....359 Quality control. Quality control measures shall insure that emission testing equipment is... 40 Protection of Environment 2 2014-07-01 2014-07-01 false Quality control. 51.359 Section 51.359... of tests) which fall into the testing categories identified. Alternatives or exceptions to...

  20. 40 CFR 51.359 - Quality control.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....359 Quality control. Quality control measures shall insure that emission testing equipment is... 40 Protection of Environment 2 2012-07-01 2012-07-01 false Quality control. 51.359 Section 51.359... of tests) which fall into the testing categories identified. Alternatives or exceptions to...

  1. 7 CFR 930.44 - Quality control.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of...

  2. 14 CFR 21.139 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which...

  3. 7 CFR 981.42 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in...

  4. 7 CFR 930.44 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 930.44 Section 930.44 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Control § 930.44 Quality control. (a) Quality standards. The Board may establish, with the approval of...

  5. 33 CFR 385.21 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Quality control. 385.21 Section... Processes § 385.21 Quality control. (a) The Corps of Engineers and the non-Federal sponsor shall prepare a quality control plan, in accordance with applicable Corps of Engineers regulations, for each product...

  6. 14 CFR 21.139 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Quality control. 21.139 Section 21.139... PROCEDURES FOR PRODUCTS AND PARTS Production Certificates § 21.139 Quality control. The applicant must show that he has established and can maintain a quality control system for any product, for which...

  7. Quality assurance and quality control in monitoring programs

    USGS Publications Warehouse

    Shampine, W.J.

    1993-01-01

    There are three general characteristics of the data to be collected in a monitoring program that should be met in order to maximize the use and value of the data: the data quality should be known the data type and quality should be consistent and comparable, and the data should be available and accessible. Potential problems with each of these characteristics are addressed effectively by quality assurance and quality control. One of the most important aspects of quality assurance in a monitoring program is the development of a quality assurance plan, which should identify clearly the quality of the data needed and describe in detail the planned actions to provide confidence that the program will meet its stated objectives. Quality control data, which allow for the quality and suitability of the environmental data to be evaluated and ascertained, should be collected and utilized as an integral part of the QA effort associated with a monitoring program.

  8. Quality Control by Artificial Vision

    SciTech Connect

    Lam, Edmond Y.; Gleason, Shaun Scott; Niel, Kurt S.

    2010-01-01

    Computational technology has fundamentally changed many aspects of our lives. One clear evidence is the development of artificial-vision systems, which have effectively automated many manual tasks ranging from quality inspection to quantitative assessment. In many cases, these machine-vision systems are even preferred over manual ones due to their repeatability and high precision. Such advantages come from significant research efforts in advancing sensor technology, illumination, computational hardware, and image-processing algorithms. Similar to the Special Section on Quality Control by Artificial Vision published two years ago in Volume 17, Issue 3 of the Journal of Electronic Imaging, the present one invited papers relevant to fundamental technology improvements to foster quality control by artificial vision, and fine-tuned the technology for specific applications. We aim to balance both theoretical and applied work pertinent to this special section theme. Consequently, we have seven high-quality papers resulting from the stringent peer-reviewing process in place at the Journal of Electronic Imaging. Some of the papers contain extended treatment of the authors work presented at the SPIE Image Processing: Machine Vision Applications conference and the International Conference on Quality Control by Artificial Vision. On the broad application side, Liu et al. propose an unsupervised texture image segmentation scheme. Using a multilayer data condensation spectral clustering algorithm together with wavelet transform, they demonstrate the effectiveness of their approach on both texture and synthetic aperture radar images. A problem related to image segmentation is image extraction. For this, O'Leary et al. investigate the theory of polynomial moments and show how these moments can be compared to classical filters. They also show how to use the discrete polynomial-basis functions for the extraction of 3-D embossed digits, demonstrating superiority over Fourier

  9. Business quality control in issuing life insurance.

    PubMed

    Roberts, N K

    1999-01-01

    Fraud investigation and fraud control are entirely different processes. Similarly the auditing of a life insurance company and the issuing of life insurance policies and business quality control are not the same. Business quality control and fraud control have much in common. In this article, these similarities are explored and a case is made that companies issuing life insurance policies should consider the business quality control approach rather than the more traditional investigatory methods. PMID:10539385

  10. Quality Control of EUVE Databases

    NASA Astrophysics Data System (ADS)

    John, Linda M.

    1993-01-01

    The publicly accessible databases for the Extreme Ultraviolet Explorer (EUVE) include: the EUVE Archive Mailserver, the Center for EUV Astrophysics ftp site, the EUVE Guest Observer Mailserver, and the Astronomical Data System node. The EUVE Performance Assurance team is responsible for verifying that these public databases are working properly and that the public availability of EUVE data contained therein does not infringe any data rights which may have been assigned. In this paper, we describe the quality assurance (QA) procedures we have developed from approaching QA as a service organization; this approach reflects the overall EUVE philosophy of QA integrated into normal operating procedures, rather than imposed as an external, post-facto, control mechanism.

  11. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Quality assurance and quality control. 136.7 Section 136.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... referred to as a spiked blank, or laboratory control sample (LCS); (v) Matrix spike (MS) and matrix...

  12. QUALITY CONTROL - VARIABILITY IN PROTOCOLS

    EPA Science Inventory

    The EPA Risk Reduction Engineering Laboratory’s Quality Assurance Office, which published the popular pocket guide Preparing Perfect Project Plans, is now introducing another quality assurance reference aid. The document Variability in Protocols (VIP) was initially designed as a ...

  13. Designing in quality through design control: a manufacturer's perspective.

    PubMed

    Lasky, F D; Boser, R B

    1997-05-01

    Quality by design is a comprehensive program that begins with understanding user needs and continues through (but does not end with) monitoring customer acceptance. Management tools and processes such as ISO 9000 standards and the Food and Drug Administration Quality System Regulations exist to guide medical device manufacturers in quality practices. The goal is to deliver products acceptable for their intended use. Quality control begins with defining attributes ranging from color to accuracy and precision. Failure mode and effects analysis and risk analysis consider both probability and severity of potential malfunctions and their effects on patients or operators. Tools used to implement design and production practices include Program Evaluation and Review Technique (PERT) charts and industry-conceived concepts, such as Six Sigma techniques. Their use varies with manufacturer, depending on product and customer needs and the manufacturer's specific quality practices. Verification confirms that input goals are met. Then, validation assures that intended clinical needs are continually satisfied by establishing adequate production specifications. Conformance is monitored to verify that stable, consistent processes are in place, and precise user instructions enable the device to satisfy its intended use. Finally, complaint tracking can help assess whether needs have been met. Modifications in service, hardware, or instructions (including quality control) might be required. Therefore, both manufacturers and users work in partnership for continual improvement. The manufacturer's knowledge of design, production, and service needs of its devices enable it to recommend appropriate quality-control protocols for clinical testing. PMID:9166255

  14. Standardised mortality ratio based on the sum of age and percentage total body surface area burned is an adequate quality indicator in burn care: An exploratory review.

    PubMed

    Steinvall, Ingrid; Elmasry, Moustafa; Fredrikson, Mats; Sjoberg, Folke

    2016-02-01

    Standardised Mortality Ratio (SMR) based on generic mortality predicting models is an established quality indicator in critical care. Burn-specific mortality models are preferred for the comparison among patients with burns as their predictive value is better. The aim was to assess whether the sum of age (years) and percentage total body surface area burned (which constitutes the Baux score) is acceptable in comparison to other more complex models, and to find out if data collected from a separate burn centre are sufficient for SMR based quality assessment. The predictive value of nine burn-specific models was tested by comparing values from the area under the receiver-operating characteristic curve (AUC) and a non-inferiority analysis using 1% as the limit (delta). SMR was analysed by comparing data from seven reference sources, including the North American National Burn Repository (NBR), with the observed mortality (years 1993-2012, n=1613, 80 deaths). The AUC values ranged between 0.934 and 0.976. The AUC 0.970 (95% CI 0.96-0.98) for the Baux score was non-inferior to the other models. SMR was 0.52 (95% CI 0.28-0.88) for the most recent five-year period compared with NBR based data. The analysis suggests that SMR based on the Baux score is eligible as an indicator of quality for setting standards of mortality in burn care. More advanced modelling only marginally improves the predictive value. The SMR can detect mortality differences in data from a single centre. PMID:26700877

  15. Quality Control in Small Groups

    NASA Astrophysics Data System (ADS)

    Lemmens, L. F.

    2008-11-01

    The smallness of some groups in a set up to control the quality of a service using questionnaires limits the size of the samples, this limitation has several consequences. Indeed the common approach used for relatively large groups, based on the central limit theorem and the law of large numbers, cannot be used anymore to construct estimators for the parameters of the model. Using an inverse probability will lift these restrictions. A questionnaire is a collection of items. In an item the respondent indicates on a Likert scale his or her agreement with a statement. Dimensions are a set of items dealing with one aspect of the service. In a questionnaire several dimensions are addressed but usually the items are presented in a random sequence. The model for an item is hierarchical with following components: a multivariate hypergeometric model takes the sampling in a finite population into account, the multinomial serves as a prior for the sampling and the Dirichlet-distribution serves as a prior for the multinomials. The composition of dimensions allows to use the posterior for one of the items as a prior for another item of that dimension and so on. After analysis of several questionnaires using this model, the reliability of the responses from some respondents turned out to be a key-problem, in the sense the responses can be classified into at least two classes and a decision rule had to be developed to neglect some of them. The influence of rejecting some answers, on the confidence for the most plausible statement can be estimated. This leads often to the result that there is only minimal evidence for the most probable statement.

  16. Colorado Air Quality Control Regulations and Ambient Air Quality Standards.

    ERIC Educational Resources Information Center

    Colorado State Dept. of Health, Denver. Div. of Air Pollution Control.

    Regulations and standards relative to air quality control in Colorado are defined in this publication. Presented first are definitions of terms, a statement of intent, and general provisions applicable to all emission control regulations adopted by the Colorado Air Pollution Control Commission. Following this, three regulations are enumerated: (1)…

  17. 30 CFR 74.6 - Quality control.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control. 74.6 Section 74.6 Mineral... DUST SAMPLING DEVICES Approval Requirements for Coal Mine Dust Personal Sampler Unit § 74.6 Quality... to maintain its quality prior to assembly of each sampler unit. In order to assure that the...

  18. Handling qualities requirements for control configured vehicles

    NASA Technical Reports Server (NTRS)

    Woodcock, R. J.; George, F. L.

    1976-01-01

    The potential effects of fly by wire and control configured vehicle concepts on flying qualities are considered. Failure mode probabilities and consequences, controllability, and dynamics of highly augmented aircraft are among the factors discussed in terms of design criteria.

  19. Quality control education in the community college

    NASA Technical Reports Server (NTRS)

    Greene, J. Griffen; Wilson, Steve

    1966-01-01

    This paper describes the Quality Control Program at Daytona Beach Junior College, including course descriptions. The program in quality control required communication between the college and the American Society for Quality Control (ASQC). The college has machinery established for certification of the learning process, and the society has the source of teachers who are competent in the technical field and who are the employers of the educational products. The associate degree for quality control does not have a fixed program, which can serve all needs, any more than all engineering degrees have identical programs. The main ideas which would be common to all quality control programs are the concept of economic control of a repetitive process and the concept of developing individual potentialities into individuals who are needed and productive.

  20. Antimisting kerosene: Base fuel effects, blending and quality control techniques

    NASA Technical Reports Server (NTRS)

    Yavrouian, A. H.; Ernest, J.; Sarohia, V.

    1984-01-01

    The problems associated with blending of the AMK additive with Jet A, and the base fuel effects on AMK properties are addressed. The results from the evaluation of some of the quality control techniques for AMK are presented. The principal conclusions of this investigation are: significant compositional differences for base fuel (Jet A) within the ASTM specification DI655; higher aromatic content of the base fuel was found to be beneficial for the polymer dissolution at ambient (20 C) temperature; using static mixer technology, the antimisting additive (FM-9) is in-line blended with Jet A, producing AMK which has adequate fire-protection properties 15 to 20 minutes after blending; degradability of freshly blended and equilibrated AMK indicated that maximum degradability is reached after adequate fire protection is obtained; the results of AMK degradability as measured by filter ratio, confirmed previous RAE data that power requirements to decade freshly blended AMK are significantly higher than equilibrated AMK; blending of the additive by using FM-9 concentrate in Jet A produces equilibrated AMK almost instantly; nephelometry offers a simple continuous monitoring capability and is used as a real time quality control device for AMK; and trajectory (jet thurst) and pressure drop tests are useful laboratory techniques for evaluating AMK quality.

  1. Professional Development for Water Quality Control Personnel.

    ERIC Educational Resources Information Center

    Shepard, Clinton Lewis

    This study investigated the availability of professional development opportunities for water quality control personnel in the midwest. The major objective of the study was to establish a listing of educational opportunities for the professional development of water quality control personnel and to compare these with the opportunities technicians…

  2. 33 CFR 385.21 - Quality control.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... DEFENSE PROGRAMMATIC REGULATIONS FOR THE COMPREHENSIVE EVERGLADES RESTORATION PLAN CERP Implementation... quality control plan, in accordance with applicable Corps of Engineers regulations, for each product that will be produced by a Project Delivery Team. The quality control plan shall be included in the...

  3. Quality Control Technician Curriculum. An Elusive Butterfly.

    ERIC Educational Resources Information Center

    Holler, Michael

    Defining and developing a quality control technician curriculum for an associate degree program is a difficult and puzzling job. There are as many definitions of quality control and curriculum ideas as there are educators asked. However, one could start by dividing the field into its major areas--heavy manufacturing, maintenance, research, and…

  4. Quality-control analytical methods: continuous quality improvement.

    PubMed

    Venti, Eden M

    2006-01-01

    It is vital that all compounding pharmacies have a continuous quality improvement program in place by way of standard operating procedures to assure that patients receive high-quality preparations. The program should take into consideration any federal and state regulatory requirements, as well as professional association expectations. Quality control measurements and regular review of those measurements are the foundations of a good quality plan. All pharmacy personnel should be aware of the importance of reporting potential internal quality concerns or problems and should be encouraged to do so without fear of repercussions. Ideally, an error-free compounding pracitice would be the goal. Since this is not practical, quality issues should not be viewed as problems, but as opportunities to improve compounding practices by correcting, before they become pervasive, the processes used in the preparation of prescriptions. PMID:23974418

  5. Water Quality Control, Curriculum Guide.

    ERIC Educational Resources Information Center

    Washington City Board of Education, NC.

    Activities which study how water is used, contaminated, and treated or purified are presented in this curriculum guide, culminating in the investigation of a local water quality problem. Designed as a 12 week mini-course for students in grades eight and nine, the guide first presents a review of the content, objectives, major concepts, and sources…

  6. Control by quality: proposition of a typology.

    PubMed

    Pujo, P; Pillet, M

    The application of Quality tools and methods in industrial management has always had a fundamental impact on the control of production. It influences the behavior of the actors concerned, while introducing the necessary notions and formalizations, especially for production systems with little or no automation, which constitute a large part of the industrial activity. Several quality approaches are applied in the workshop and are implemented at the level of the control. In this paper, the authors present a typology of the various approaches that have successively influenced control, such as statistical process control, quality assurance, and continuous improvement. First the authors present a parallel between production control and quality organizational structure. They note the duality between control, which is aimed at increasing productivity, and quality, which aims to satisfy the needs of the customer. They also note the hierarchical organizational structure of these two systems of management with, at each level, the notion of a feedback loop. This notion is fundamental to any kind of decision making. The paper is organized around the operational, tactical, and strategic levels, by describing for each level the main methods and tools for control by quality. The overview of these tools and methods starts at the operational level, with the Statistical Process Control, the Taguchi technique, and the "six sigma" approach. On the tactical level, we find a quality system approach, with a documented description of the procedures introduced in the firm. The management system can refer here to Quality Assurance, Total Productive Maintenance, or Management by Total Quality. The formalization through procedures of the rules of decision governing the process control enhances the validity of these rules. This leads to the enhancement of their reliability and to their consolidation. All this counterbalances the human, intrinsically fluctuating, behavior of the control

  7. Quality Control Using Optical Probe Arrays

    NASA Astrophysics Data System (ADS)

    Stewart, Robert M.

    1989-01-01

    Low cost, optical probes, can be combined into an inspection array, and the go/no-go outputs can be analyzed by a high speed programmable logic controller (PLC). The PLC can be remotely addressed to change the desired level of quality control. The PLC can provide on-line data for blow-by-blow statistical process control (SPC).

  8. [Quality control of printed patient information].

    PubMed

    Herm, Kerstin; Linden, Michael

    2013-05-01

    Printed material is an important part in patient information and is called bibliotherapy. It is subject to quality control similar to any other types of treatment. This paper presents an outline of important quality criteria and methods of quality control. Important quality criteria are: (a) Correctness and validity of content evaluated by mentioning the expertise of the authors, appraisal through external experts, reference to scientific literature, and empirical tests of the content, (b) Readability in respect to text structure measured by the "Flesch-Reading-Ease-Formula" supported by fair graphical design including fond and structure of text, (c) Comprehensibility tested by feedback of patients or standardized by the Hamburg comprehensibility rating, (d) Utility including securing availability, acceptance, differential indication and use. Writing and publication of patient leaflets must be accompanied by quality control measures. PMID:23446824

  9. Quality control procedures in the Italian national forest inventory.

    PubMed

    Gasparini, Patrizia; Bertani, Remo; De Natale, Flora; Di Cosmo, Lucio; Pompei, Enrico

    2009-04-01

    National forest inventories represent a fundamental source of data and knowledge for forestry and environmental policy and allow for the production of national and regional level statistics on forests. The value of these statistics confirms the need for a sampling design that adequately delivers representation by reducing sampling error, but also for a data quality process that limits the non-sampling errors. The article summarizes the quality control procedures of the three sampling phases adopted in the Italian national forest inventory, carried out between 2003 and 2006. The development of an integrated system of actions and controls which are able to limit subjective interpretations, in order to guarantee harmonized information all over the country, was a considerable effort within the overall project. Critical points to be considered were the consistent number of measures and evaluations undertaken during the three inventory phases, the high variability of observed attributes, the consistent number of surveyors involved, and costs of quality control, especially those related to fieldwork. At the end, examples on the overall quality of the classification performed on land cover and vegetation are discussed, as well as the impact of classification errors on the total forest area estimates. PMID:19557227

  10. Quality Control Systems in Cardiac Aging

    PubMed Central

    Quarles, Ellen K; Dai, Dao-Fu; Tocchi, Autumn; Basisty, Nathan; Gitari, Lemuel; Rabinovitch, Peter S

    2015-01-01

    Cardiac aging is an intrinsic process that results in impaired cardiac function, along with cellular and molecular changes. These degenerative changes are intimately associated with quality control mechanisms. This review provides a general overview of the clinical and cellular changes which manifest in cardiac aging, and the quality control mechanisms involved in maintaining homeostasis and retarding aging. These mechanisms include autophagy, ubiquitin-mediated turnover, apoptosis, mitochondrial quality control and cardiac matrix homeostasis. Finally, we discuss aging interventions that have been observed to impact cardiac health outcomes. These include caloric restriction, rapamycin, resveratrol, GDF11, mitochondrial antioxidants and cardiolipin-targeted therapeutics. A greater understanding of the quality control mechanisms that promote cardiac homeostasis will help to understand the benefits of these interventions, and hopefully lead to further improved therapeutic modalities. PMID:25702865

  11. Quality control of automated cell counters.

    PubMed

    Cembrowski, George S; Clarke, Gwen

    2015-03-01

    The hematology analyzers of today provide more reproducible analyses compared with those of a few decades ago, necessitating an evolution in hematology quality practices. The improved performance allows use of simple quality control rules. This improved performance also renders the repeat analysis of critical value specimens non value added. Some of the patient averaging techniques have become outmoded and need to be replaced by less complicated calculations but with truncation of predictable outlying populations. The ready availability of comparative peer quality control values helps to improve analyzer precision and accuracy, and simplifies instrument validation and calibration. PMID:25676372

  12. [The quality of biological information: standardization and quality control].

    PubMed

    Giampaoli, S; Muti, P

    1992-01-01

    Some procedures and methods for the measurement of cardiovascular risk factor are described; in particular of anthropometric measurements (weight, height, arm circumference, wrist circumference, hip circumference) of blood pressure, of electrocardiogram and of blood samples for the preservation of biological specimens. Some advice for the quality control during screening activities are reported. PMID:1492736

  13. 40 CFR 136.7 - Quality assurance and quality control.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... PROGRAMS (CONTINUED) GUIDELINES ESTABLISHING TEST PROCEDURES FOR THE ANALYSIS OF POLLUTANTS § 136.7 Quality... referred to as a spiked blank, or laboratory control sample (LCS); (v) Matrix spike (MS) and matrix spike duplicate (MSD), or laboratory fortified matrix (LFM) and LFM duplicate, may be used for suspected...

  14. QUALITY ASSURANCE AND QUALITY CONTROL FOR RADIOCHEMICAL ANALYSES AND MEASUREMENTS

    EPA Science Inventory

    Require that each batch of samples analyzed be accompanied by appropriate quality control samples to evaluate accuracy and precision of the results. Require a documented data review and validation process by a minimum of three people before data is released to the client. Requi...

  15. Network-based production quality control

    NASA Astrophysics Data System (ADS)

    Kwon, Yongjin; Tseng, Bill; Chiou, Richard

    2007-09-01

    This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

  16. [Internal Quality Control and External Quality Assessment on POCT].

    PubMed

    Kuwa, Katsuhiko

    2015-02-01

    The quality management (QM) of POCT summarizes its internal quality control (IQC) and external quality assessment (EQA). For QM requirements in POCT, ISO 22870-Point-of-care testing (POCT) -Requirements for quality and competence and ISO 15189-Medical laboratories-Requirements for quality and competence, it is performed under the guidance of the QM committee. The role of the POC coordinator and/or medical technologist of the clinical laboratory is important. On measurement performance of POCT devices, it is necessary to confirm data on measurement performance from the manufacturer other than those in the inserted document. In the IQC program, the checking and control of measurement performance are the targets. On measurements of QC samples by the manufacturer, it is essential to check the function of devices. In addition, regarding the EQA program, in 2 neighboring facilities, there is an effect to confirm the current status of measurement and commutability assessment in these laboratories using whole blood along with residual blood samples from daily examinations in the clinical laboratory. PMID:26529974

  17. Microbiological quality and quality control of purified water and ultrapure dialysis fluids for online hemodiafiltration in routine clinical practice.

    PubMed

    Penne, E Lars; Visser, Linda; van den Dorpel, Marinus A; van der Weerd, Neelke C; Mazairac, Albert H A; van Jaarsveld, Brigit C; Koopman, Marion G; Vos, Pieter; Feith, Geert W; Kremer Hovinga, Ton K; van Hamersvelt, Henk W; Wauters, Inge M; Bots, Michiel L; Nubé, Menso J; Ter Wee, Piet M; Blankestijn, Peter J; Grooteman, Muriel P C

    2009-09-01

    During online hemodiafiltration, patients are directly infused with sterile substitution solutions to maintain fluid balance. Adequate water treatment and a well-organized quality control process are essential to provide non-pyrogenic fluids with consistent optimal quality. We sought to assess water quality, the water treatment system, and the methods for surveillance of microbiological water quality in 10 Dutch dialysis centers that routinely treat patients with hemodiafiltration. Microbiological monitoring results (micro-organisms and endotoxins) were collected over a 1-year period representing 11,258 hemodiafiltration sessions covering 97 patients. In all centers, water purification was based on a reverse osmosis module in combination with a second reverse osmosis and/or an electrodeionizer. All centers regularly and routinely monitored the microbiological purity of the dialysis water with adequate analytical methods but with variable monitoring frequency. Microbiological assessments were compliant with reference quality levels in 3923 of 3961 samples. Our study suggests that non-pyrogenic substitution fluids can be produced online for a prolonged period of time. It is likely that the current Dutch Quality of Care Guideline has contributed to high-quality water treatment and a well-organized control process. PMID:19606080

  18. Asbestos/NESHAP adequately wet guidance

    SciTech Connect

    Shafer, R.; Throwe, S.; Salgado, O.; Garlow, C.; Hoerath, E.

    1990-12-01

    The Asbestos NESHAP requires facility owners and/or operators involved in demolition and renovation activities to control emissions of particulate asbestos to the outside air because no safe concentration of airborne asbestos has ever been established. The primary method used to control asbestos emissions is to adequately wet the Asbestos Containing Material (ACM) with a wetting agent prior to, during and after demolition/renovation activities. The purpose of the document is to provide guidance to asbestos inspectors and the regulated community on how to determine if friable ACM is adequately wet as required by the Asbestos NESHAP.

  19. Quality control of a teleradiology system

    NASA Astrophysics Data System (ADS)

    Lyche, David K.; Willis, Charles E.; Williamson, Morgan P.; Suitor, Charles T.; Romlein, John R.

    1996-04-01

    Teleradiology is being implemented in the U.S. military. Soft-copy reading of computed radiology (CR) images and film-digitizer (FD) images are becoming a common practice. The Medical Diagnostic Imaging Support (MDIS) Office at the Medical Advanced Technology Management Office (MATMO), Fort Detrick, Maryland, installed an 'off-the-shelf' DICOM teleradiology system by which CR images and FD images acquired at Hickam Air Force Base (AFB), Hawaii, are transmitted electronically over a T-1 telecommunications line to Tripler Army Medical Center (TAMC), Hawaii. The goal was to provide a diagnostic quality teleradiology system to the military services to extend the expertise and training of physicians to remote sites. In order to guarantee a diagnostic quality image throughout the system, a rigid set of quality control standards had to be designed and implemented. This poster presents the results of a successful teleradiology implementation where quality control is maintained throughout the imaging chain.

  20. Quality control by a mobile molecular workshop: Quality versus quantity

    NASA Astrophysics Data System (ADS)

    Sharma, Ajeet K.; Chowdhury, Debashish

    2010-09-01

    Ribosome is a molecular machine that moves on a messenger RNA (mRNA) track while, simultaneously, polymerizing a protein using the mRNA also as the corresponding template. We define, and analytically calculate, two different measures of the efficiency of this machine. However, we argue that its performance is evaluated better in terms of the translational fidelity and the speed with which it polymerizes a protein. We define both these quantities and calculate these analytically. Fidelity is a measure of the quality of the products, while the total quantity of products synthesized in a given interval depends on the speed of polymerization. We show that for synthesizing a large quantity of proteins, it is not necessary to sacrifice the quality. We also explore the effects of the quality control mechanism on the strength of mechanochemical coupling. We suggest experiments for testing some of the ideas presented here.

  1. Harmonisation Initiatives of Copernicus Data Quality Control

    NASA Astrophysics Data System (ADS)

    Vescovi, F. D.; Lankester, T.; Coleman, E.; Ottavianelli, G.

    2015-04-01

    The Copernicus Space Component Data Access system (CSCDA) incorporates data contributions from a wide range of satellite missions. Through EO data handling and distribution, CSCDA serves a set of Copernicus Services related to Land, Marine and Atmosphere Monitoring, Emergency Management and Security and Climate Change. The quality of the delivered EO products is the responsibility of each contributing mission, and the Copernicus data Quality Control (CQC) service supports and complements such data quality control activities. The mission of the CQC is to provide a service of quality assessment on the provided imagery, to support the investigation related to product quality anomalies, and to guarantee harmonisation and traceability of the quality information. In terms of product quality control, the CQC carries out analysis of representative sample products for each contributing mission as well as coordinating data quality investigation related to issues found or raised by Copernicus users. Results from the product analysis are systematically collected and the derived quality reports stored in a searchable database. The CQC service can be seen as a privileged focal point with unique comparison capacities over the data providers. The comparison among products from different missions suggests the need for a strong, common effort of harmonisation. Technical terms, definitions, metadata, file formats, processing levels, algorithms, cal/val procedures etc. are far from being homogeneous, and this may generate inconsistencies and confusion among users of EO data. The CSCDA CQC team plays a significant role in promoting harmonisation initiatives across the numerous contributing missions, so that a common effort can achieve optimal complementarity and compatibility among the EO data from multiple data providers. This effort is done in coordination with important initiatives already working towards these goals (e.g. INSPIRE directive, CEOS initiatives, OGC standards, QA4EO

  2. Protein quality control in the bacterial periplasm.

    PubMed

    Merdanovic, Melisa; Clausen, Tim; Kaiser, Markus; Huber, Robert; Ehrmann, Michael

    2011-01-01

    Protein quality control involves sensing and treatment of defective or incomplete protein structures. Misfolded or mislocalized proteins trigger dedicated signal transduction cascades that upregulate the production of protein quality-control factors. Corresponding proteases and chaperones either degrade or repair damaged proteins, thereby reducing the level of aggregation-prone molecules. Because the periplasm of gram-negative bacteria is particularly exposed to environmental changes and respective protein-folding stresses connected with the presence of detergents, low or high osmolarity of the medium, elevated temperatures, and the host's immune response, fine-tuned protein quality control systems are essential for survival under these unfavorable conditions. This review discusses recent advances in the identification and characterization of the key cellular factors and the emerging general principles of the underlying molecular mechanisms. PMID:21639788

  3. Post-translational Modification and Quality Control

    PubMed Central

    Wang, Xuejun; Pattison, J. Scott; Su, Huabo

    2013-01-01

    Protein quality control (PQC) functions to minimize the level and toxicity of misfolded proteins in the cell. PQC is performed by intricate collaboration among chaperones and target protein degradation. The latter is carried out primarily by the ubiquitin-proteasome system and perhaps autophagy. Terminally misfolded proteins that are not timely removed tend to form aggregates. Their clearance requires macroautophagy. Macroautophagy serves in intracellular quality control also by selectively segregating defective organelles (e.g., mitochondria) and targeting them for degradation by the lysosome. Inadequate PQC is observed in a large subset of failing human hearts with a variety of etiologies and its pathogenic role has been experimentally demonstrated. Multiple post-translational modifications (PTMs) can occur to substrate proteins and/or PQC machineries, promoting or hindering the removal of the misfolded proteins. This article highlights recent advances in PTMs-mediated regulation of intracellular quality control mechanisms and its known involvement in cardiac pathology. PMID:23329792

  4. HPLC for quality control of polyimides

    NASA Technical Reports Server (NTRS)

    Young, P. R.; Sykes, G. F.

    1979-01-01

    High Pressure Liquid Chromatography (HPLC) as a quality control tool for polyimide resins and prepregs are presented. A data base to help establish accept/reject criteria for these materials was developed. This work is intended to supplement, not replace, standard quality control tests normally conducted on incoming resins and prepregs. To help achieve these objectives, the HPLC separation of LARC-160 polyimide precursor resin was characterized. Room temperature resin aging effects were studied. Graphite reinforced composites made from fresh and aged resin were fabricated and tested to determine if changes observed by HPLC were significant.

  5. Quality control in the secretory assembly line.

    PubMed Central

    Helenius, A

    2001-01-01

    As a rule, only proteins that have reached a native, folded and assembled structure are transported to their target organelles and compartments within the cell. In the secretory pathway of eukaryotic cells, this type of sorting is particularly important. A variety of molecular mechanisms are involved that distinguish between folded and unfolded proteins, modulate their intracellular transport, and induce degradation if they fail to fold. This phenomenon, called quality control, occurs at several levels and involves different types of folding sensors. The quality control system provides a stringent and versatile molecular sorting system that guaranties fidelity of protein expression in the secretory pathway. PMID:11260794

  6. Rotorcraft flying qualities improvement using advanced control

    NASA Technical Reports Server (NTRS)

    Walker, D.; Postlethwaite, I.; Howitt, J.; Foster, N.

    1993-01-01

    We report on recent experience gained when a multivariable helicopter flight control law was tested on the Large Motion Simulator (LMS) at DRA Bedford. This was part of a study into the application of multivariable control theory to the design of full-authority flight control systems for high-performance helicopters. In this paper, we present some of the results that were obtained during the piloted simulation trial and from subsequent off-line simulation and analysis. The performance provided by the control law led to level 1 handling quality ratings for almost all of the mission task elements assessed, both during the real-time and off-line analysis.

  7. Development of electronic potential and current transducers suitable for gas insulated switchgear and adequate for application to substation digital control systems

    SciTech Connect

    Tokoro, K.; Harumoto, Y.; Ida, Y.; Mukae, H.; Ohno, Y.; Shimada, M.; Yamamoto, H.; Yoshida, Y.

    1982-10-01

    Substation Digital Control System (SDCS) had been developed for the future system controlling the large scale power system. For application of SDCS to Gas Insulated Switchgear (GIS), electronic potential and current transducers fit for GIS have been developed. This equipment is composed of a capacitive dividing type potential transducer, a low burden current transformer, an analogue-to-digital conversion unit and an optical fiber signal transmit system. Good performance is confirmed by the application tests simulating the field circumstances.

  8. Protein Quality Control and Metabolism: Bidirectional Control in the Heart

    PubMed Central

    Wang, Zhao V.; Hill, Joseph A.

    2015-01-01

    The prevalence of heart disease, especially heart failure, continues to increase, and cardiovascular disease remains the leading cause of death worldwide. As cardiomyocytes are essentially irreplaceable, protein quality control is pivotal to cellular homeostasis and, ultimately, cardiac performance. Three evolutionarily conserved mechanisms – autophagy, the unfolded protein response, and the ubiquitin-proteasome system– act in concert to degrade misfolded proteins and eliminate defective organelles. Recent advances have revealed that these mechanisms are intimately associated with cellular metabolism. Going forward, comprehensive understanding of the role of protein quality control mechanisms in cardiac pathology will require integration of metabolic pathways and metabolic control. PMID:25651176

  9. [Quality control of Maca (Lepidium meyenii)].

    PubMed

    Shu, Ji-cheng; Cui, Hang-qing; Huang, Ying-zheng; Huang, Xiao-ying; Yang, Ming

    2015-12-01

    To control the quality of Maca, the quality standard was established in this study. According to the methods recorded in the Appendix of Chinese Pharmacopoeia (2010 Edition), the water, extract, total ash, acid insoluble substance, and heavy metals inspections in Lepidium meyenii were carried out. N-benzyl-9Z, 12Z-octadecadienamide in L. meyenii was identified by TLC, and it was determined by HPLC. The results showed that the N-benzyl-9Z, 12Z-octadecadienamide identification of TLC was a strong mark and specificity. In content determination experiment, the linearity of N-benzyl-9Z, 12Z-octadecadienamide was in the range of 0.01-2 microg (r = 0.9998), and the average recovery (n=9) was 99.27% (RSD 2.0%). The methods were simple, accurate, with good reproducibility. It is suitable for quality control L. meyenii. PMID:27141660

  10. Outsourcing University Degrees: Implications for Quality Control

    ERIC Educational Resources Information Center

    Edwards, Julie; Crosling, Glenda; Edwards, Ron

    2010-01-01

    Education institutions worldwide have and continue to seek opportunities to spread their offerings abroad. While the provision of courses to students located overseas through partner institutions has many advantages, it raises questions about quality control that are not as applicable to other forms of international education. This paper uses a…

  11. 33 CFR 385.21 - Quality control.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... will be produced by a Project Delivery Team. The quality control plan shall be included in the Project Management Plan and shall describe the procedures to be used to ensure compliance with technical and policy requirements during implementation. (b) During development of the Project Management Plan for each project,...

  12. 33 CFR 385.21 - Quality control.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... will be produced by a Project Delivery Team. The quality control plan shall be included in the Project Management Plan and shall describe the procedures to be used to ensure compliance with technical and policy requirements during implementation. (b) During development of the Project Management Plan for each project,...

  13. 33 CFR 385.21 - Quality control.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... will be produced by a Project Delivery Team. The quality control plan shall be included in the Project Management Plan and shall describe the procedures to be used to ensure compliance with technical and policy requirements during implementation. (b) During development of the Project Management Plan for each project,...

  14. Acoustic resonance techniques for quality control

    SciTech Connect

    Sinha, D.N.

    1992-09-01

    Acoustic resonance based nondestructive techniques are described that can be used for both process and quality control in manufacturing. The Acoustic Resonance Spectroscopy (AS) technique is highlighted for its capability in fluid property (flow, density, viscosity, and speed of sound) monitoring. Possible applications of these noninvasive techniques for textile manufacturing are pointed out.

  15. Acoustic resonance techniques for quality control

    SciTech Connect

    Sinha, D.N.

    1992-01-01

    Acoustic resonance based nondestructive techniques are described that can be used for both process and quality control in manufacturing. The Acoustic Resonance Spectroscopy (AS) technique is highlighted for its capability in fluid property (flow, density, viscosity, and speed of sound) monitoring. Possible applications of these noninvasive techniques for textile manufacturing are pointed out.

  16. Quality Control & Design in Science Learning

    ERIC Educational Resources Information Center

    Sumrall, William J.; Schillinger, Don

    2003-01-01

    One area of science education that is, at times, neglected involves lessons on technological concepts of these principles--designing, testing, and quality control. Instead, a focus upon science concepts from a pure, and unapplied, perspective is the norm. Thus, while students may learn the equation "mass divided by volume equals density," the…

  17. School meals in Catalonia: surveillance and quality control.

    PubMed

    Roset, M A; Gonzalvo, B

    2001-12-01

    The Education Council of the Catalonian government drew up a programme to improve the quality control of school canteens in Catalonia. The objectives of this programme were to contribute to developing healthier eating habits in school children through school canteens and to improve school canteen services considering other aspects such as service, operation, management, end-users, frontline staff and supervisors of menu planning. This paper deals with two programme components aiming at introducing Nutrition in the school syllabus and school menu assessment. Various departments, organisations and associations were involved in programme development and implementation. Initial analysis was based on information collected from formal administrative reports completed by a survey on 100 primary schools. From this preliminary analysis it was concluded that problem identification needs to be completed by an understanding of underlying reasons in order to design adequate solutions and guarantee implementation. PMID:11918476

  18. Comorbidity Structure of Psychological Disorders in the Online e-PASS Data as Predictors of Psychosocial Adjustment Measures: Psychological Distress, Adequate Social Support, Self-Confidence, Quality of Life, and Suicidal Ideation

    PubMed Central

    Klein, Britt; Meyer, Denny

    2014-01-01

    Background A relative newcomer to the field of psychology, e-mental health has been gaining momentum and has been given considerable research attention. Although several aspects of e-mental health have been studied, 1 aspect has yet to receive attention: the structure of comorbidity of psychological disorders and their relationships with measures of psychosocial adjustment including suicidal ideation in online samples. Objective This exploratory study attempted to identify the structure of comorbidity of 21 psychological disorders assessed by an automated online electronic psychological assessment screening system (e-PASS). The resulting comorbidity factor scores were then used to assess the association between comorbidity factor scores and measures of psychosocial adjustments (ie, psychological distress, suicidal ideation, adequate social support, self-confidence in dealing with mental health issues, and quality of life). Methods A total of 13,414 participants were assessed using a complex online algorithm that resulted in primary and secondary Diagnostic and Statistical Manual of Mental Disorders (Fourth Edition, Text Revision) diagnoses for 21 psychological disorders on dimensional severity scales. The scores on these severity scales were used in a principal component analysis (PCA) and the resulting comorbidity factor scores were related to 4 measures of psychosocial adjustments. Results A PCA based on 17 of the 21 psychological disorders resulted in a 4-factor model of comorbidity: anxiety-depression consisting of all anxiety disorders, major depressive episode (MDE), and insomnia; substance abuse consisting of alcohol and drug abuse and dependency; body image–eating consisting of eating disorders, body dysmorphic disorder, and obsessive-compulsive disorders; depression–sleep problems consisting of MDE, insomnia, and hypersomnia. All comorbidity factor scores were significantly associated with psychosocial measures of adjustment (P<.001). They were

  19. 42 CFR 84.40 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control plans; filing requirements. 84.40... Control § 84.40 Quality control plans; filing requirements. As a part of each application for approval or... proposed quality control plan which shall be designed to assure the quality of respiratory...

  20. 30 CFR 28.30 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control plans; filing requirements. 28... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed...

  1. 21 CFR 211.22 - Responsibilities of quality control unit.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Responsibilities of quality control unit. 211.22... Personnel § 211.22 Responsibilities of quality control unit. (a) There shall be a quality control unit that... have been fully investigated. The quality control unit shall be responsible for approving or...

  2. 30 CFR 28.30 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control plans; filing requirements. 28... PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.30 Quality control plans; filing... part, each applicant shall file with MSHA a proposed quality control plan which shall be designed...

  3. 42 CFR 84.40 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 1 2011-10-01 2011-10-01 false Quality control plans; filing requirements. 84.40... Control § 84.40 Quality control plans; filing requirements. As a part of each application for approval or... proposed quality control plan which shall be designed to assure the quality of respiratory...

  4. Practicing Quality Control in a Bioanalytical Experiment

    NASA Astrophysics Data System (ADS)

    Marcos, Juliana; Ríos, Angel; Valcárcel, Miguel

    1995-10-01

    The quality of analytical results frequently requires assessment, which has fostered treatment of this subject in a host of chemical books for students. Accordingly, new experiments need to be devised in order to help students adapt to it. This paper presents a straightforward exercise to demonstrate how quality control and the analysis of variance technique are implemented in practice. The exercise also is attractive because the analyte (chlorophyl) is determined in real samples (plants) that students can collect by themselves. In this way, they can realize the significance of sampling and learn how to do it properly.

  5. Quality and Control of Water Vapor Winds

    NASA Technical Reports Server (NTRS)

    Jedlovec, Gary J.; Atkinson, Robert J.

    1996-01-01

    Water vapor imagery from the geostationary satellites such as GOES, Meteosat, and GMS provides synoptic views of dynamical events on a continual basis. Because the imagery represents a non-linear combination of mid- and upper-tropospheric thermodynamic parameters (three-dimensional variations in temperature and humidity), video loops of these image products provide enlightening views of regional flow fields, the movement of tropical and extratropical storm systems, the transfer of moisture between hemispheres and from the tropics to the mid- latitudes, and the dominance of high pressure systems over particular regions of the Earth. Despite the obvious larger scale features, the water vapor imagery contains significant image variability down to the single 8 km GOES pixel. These features can be quantitatively identified and tracked from one time to the next using various image processing techniques. Merrill et al. (1991), Hayden and Schmidt (1992), and Laurent (1993) have documented the operational procedures and capabilities of NOAA and ESOC to produce cloud and water vapor winds. These techniques employ standard correlation and template matching approaches to wind tracking and use qualitative and quantitative procedures to eliminate bad wind vectors from the wind data set. Techniques have also been developed to improve the quality of the operational winds though robust editing procedures (Hayden and Veldon 1991). These quality and control approaches have limitations, are often subjective, and constrain wind variability to be consistent with model derived wind fields. This paper describes research focused on the refinement of objective quality and control parameters for water vapor wind vector data sets. New quality and control measures are developed and employed to provide a more robust wind data set for climate analysis, data assimilation studies, as well as operational weather forecasting. The parameters are applicable to cloud-tracked winds as well with minor

  6. [Dynamic behavior of the adaptive control system, hypothalamus--anterior pituitary--adrenal cortex. Animal experimental study of the adequate system dynamics of the direct and indirect parameters of the adaptive control system].

    PubMed

    Zintzsch, I; Seidel, H; Lantzsch, C; Lantzsch, M

    1979-01-01

    The dynamic response of the adaptive closed-loop control system hypothalamus-anterior pituitary-adrenal cortex after application of short-time disturb pulses were examined experimentally in the pig. Blood sampling was performed biologically non-reactive by chronically implanted vascular catheters in the upper vena cava. A circadian biphase periodical dynamics characterizes the distrubance response of the adaptive control system, respectively, its direct and indirect parameters. After distrubance variables induced initial excess the plasma corticosteriods undershoot the basic level over a long period. Conversely, the dynamics of the eosinophils is determined through an initial eosinopenic phase and a subsequent typical overshoot. Periodical dynamic is absent in the steady state. The controller of the adaptive system does not show any spontaneous activity in the steady state without stress. The absence of an endogenic periodicity of the dependent parameters likewise gives evidence of an active oscillator. On the other hand, the controlling unit of the adaptive system constitutes a control response of circadian periodicty after activation by disturbance variables in pulse shape. The high damping of the control system terminates the transient state within 24 hours, and the corticosteriods and the eosinophils reach the steady state level. This control quality of the adaptive control system gains a high importance in the origination of the spontaneous circadian periodicity by corticosteriods and eosinophils and for the biological compensation of exogenous distrubance variables. PMID:233184

  7. Laboratory quality control based on risk management.

    PubMed

    Nichols, James H

    2011-01-01

    Risk management is the systematic application of management policies, procedures, and practices to the tasks of analyzing, evaluating, controlling and monitoring risk (the effect of uncertainty on objectives). Clinical laboratories conduct a number of activities that could be considered risk management including verification of performance of new tests, troubleshooting instrument problems and responding to physician complaints. Development of a quality control plan for a laboratory test requires a process map of the testing process with consideration for weak steps in the preanalytic, analytic and postanalytic phases of testing where there is an increased probability of errors. Control processes that either prevent or improve the detection of errors can be implemented at these weak points in the testing process to enhance the overall quality of the test result. This manuscript is based on a presentation at the 2nd International Symposium on Point of Care Testing held at King Faisal Specialist Hospital in Riyadh, Saudi Arabia on October 12-13, 2010. Risk management principles will be reviewed and progress towards adopting a new Clinical and Laboratory Standards Institute Guideline for developing laboratory quality control plans based on risk management will be discussed. PMID:21623049

  8. Protein quality control in the nucleus.

    PubMed

    Jones, Ramon D; Gardner, Richard G

    2016-06-01

    The nucleus is the repository for the eukaryotic cell's genetic blueprint, which must be protected from harm to ensure survival. Multiple quality control (QC) pathways operate in the nucleus to maintain the integrity of the DNA, the fidelity of the DNA code during replication, its transcription into mRNA, and the functional structure of the proteins that are required for DNA maintenance, mRNA transcription, and other important nuclear processes. Although we understand a great deal about DNA and RNA QC mechanisms, we know far less about nuclear protein quality control (PQC) mechanisms despite that fact that many human diseases are causally linked to protein misfolding in the nucleus. In this review, we discuss what is known about nuclear PQC and we highlight new questions that have emerged from recent developments in nuclear PQC studies. PMID:27015023

  9. Quality control analytical methods: strategies to ensure a robust quality-control microbiology program.

    PubMed

    Griffiths, Tricia; Connors, Anne

    2013-01-01

    As the regulatory environment for compounding pharmacies continues to evolve, facilities can take immediate steps to strengthen their quality-control microbiology and environmental monitoring programs. Robust programs that are timely, comprehensive, and effective will minimize risk and help support positive patient outcomes. This article provides a roadmap for putting in place a robust quality-control microbiology program in the face of United States Pharmacopeia Chapter 797 standards, and highlights several technologies for environmental monitoring that support a successful program. PMID:23696174

  10. Towards quality control of food using terahertz

    NASA Astrophysics Data System (ADS)

    Ung, B. S.-Y.; Fischer, B. M.; Ng, B. W.-H.; Abbott, D.

    2007-12-01

    Terahertz radiation or T-rays, show promise in quality control of food products. As T-rays are inherently sensitive to water, they are very suitable for moisture detection. This proves to be a valuable asset in detecting the moisture content of dried food, a critical area for some products. As T-rays are transparent to plastics, food additives can also be probed through the packaging, providing checks against a manufacturer's claims, such as the presence of certain substances in foods.

  11. How intense quality control improves hydraulic fracturing

    SciTech Connect

    Ely, J.W.

    1996-11-01

    Not unlike the subject of Forced Closure, Intense Quality Control is probably misnamed. What actually is discussed in this article is pilot testing of the fracturing fluids actually pumped at in-situ conditions of temperature and shear. Presented here is development of the need for onsite testing, equipment used, shear and viscosity curves from several jobs showing what went wrong that would otherwise not have been known, and a discussion of borate gel fluids.

  12. 7 CFR 58.335 - Quality control tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on...

  13. 7 CFR 58.335 - Quality control tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on...

  14. 7 CFR 58.928 - Quality control tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall...

  15. 7 CFR 58.928 - Quality control tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall...

  16. 7 CFR 58.642 - Quality control tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.642 Section 58.642... Procedures § 58.642 Quality control tests. All mix ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow line samples...

  17. 7 CFR 58.642 - Quality control tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Quality control tests. 58.642 Section 58.642... Procedures § 58.642 Quality control tests. All mix ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow line samples...

  18. KLT-based quality controlled compression of single-lead ECG.

    PubMed

    Blanchett, T; Kember, G C; Fenton, G A

    1998-07-01

    An electrocardiogram (ECG) compression algorithm based on a combination of the Karhunen-Loeve transform (KLT) and multirate sampling is introduced. The use of multirate sampling reduces KLT computational times to those reported for wavelet-packet-based compression techniques. A beat-by-beat quality controlled compression criterion is shown to be necessary to ensure clinically adequate reconstruction of each beat. The resulting quality controlled algorithm efficiently achieves compression rates of approximately 30-40:1 for the MIT-BIH database. PMID:9644904

  19. 21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... and Process Control System: Requirements for Quality Control § 111.117 What quality control operations are required for equipment, instruments, and controls? Quality control operations for equipment... 21 Food and Drugs 2 2011-04-01 2011-04-01 false What quality control operations are required...

  20. 21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false What quality control operations are required for... and Process Control System: Requirements for Quality Control § 111.117 What quality control operations are required for equipment, instruments, and controls? Quality control operations for...

  1. 21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 2 2014-04-01 2014-04-01 false What quality control operations are required for... and Process Control System: Requirements for Quality Control § 111.117 What quality control operations are required for equipment, instruments, and controls? Quality control operations for...

  2. Optimization and quality control of computed radiography

    NASA Astrophysics Data System (ADS)

    Willis, Charles E.; Weiser, John C.; Leckie, Robert G.; Romlein, John R.; Norton, Gary S.

    1994-05-01

    Computed radiography (CR) is a relatively new technique for projection radiography. Few hospitals have CR devices in routine service and only a handful have more than one CR unit. As such, the clinical knowledge base does not yet exist to establish quality control (QC) procedures for CR devices. Without assurance that CR systems are operating within nominal limits, efforts to optimize CR performance are limited in value. A complete CR system includes detector plates that vary in response, cassettes, an electro-optical system for developing the image, computer algorithms for processing the raw image, and a hard copy output device. All of these subsystems are subject to variations in performance that can degrade image quality. Using CR manufacturer documentation, we have defined acceptance protocols for two different Fuji CR devices, the FCR 7000 and the AC1+, and have applied these tests to ten individual machines. We have begun to establish baseline performance measures and to determine measurement frequencies. CR QC is only one component of the overall quality control for totally digital radiology departments.

  3. Quality control in the year 2000

    PubMed Central

    Schade, Bernd

    1992-01-01

    ‘Just-in-time’ production is a prerequisite for a company to meet the challenges of competition. Manufacturing cycles have been so successfully optimized that release time now has become a significant factor. A vision for a major quality-control (QC) contribution to profitability in this decade seems to be the just-in-time release. Benefits will go beyond cost savings for lower inventory. The earlier detection of problems will reduce rejections and scrap. In addition, problem analysis and problem-solving will be easier. To achieve just-in-time release, advanced automated systems like robots will become the workhorses in QC for high volume pharmaceutical production. The requirements for these systems are extremely high in terms of quality, reliability and ruggedness. Crucial for the success might be advances in use of microelectronics for error checks, system recording, trouble shooting, etc. as well as creative new approaches (for example the use of redundant assay systems). PMID:18924930

  4. Quality control in the year 2000.

    PubMed

    Schade, B

    1992-01-01

    'Just-in-time' production is a prerequisite for a company to meet the challenges of competition. Manufacturing cycles have been so successfully optimized that release time now has become a significant factor. A vision for a major quality-control (QC) contribution to profitability in this decade seems to be the just-in-time release. Benefits will go beyond cost savings for lower inventory. The earlier detection of problems will reduce rejections and scrap. In addition, problem analysis and problem-solving will be easier. To achieve just-in-time release, advanced automated systems like robots will become the workhorses in QC for high volume pharmaceutical production. The requirements for these systems are extremely high in terms of quality, reliability and ruggedness. Crucial for the success might be advances in use of microelectronics for error checks, system recording, trouble shooting, etc. as well as creative new approaches (for example the use of redundant assay systems). PMID:18924930

  5. Mammographic equipment, technique, and quality control

    SciTech Connect

    Friedrich, M.A. )

    1991-08-01

    The most important improvements in mammographic technique were the introduction of single- or double-emulsion high-contrast film-screen combinations for mammography, the use of a specially designed low-kilovoltage Bucky grid to reduce scattered radiation, and the introduction of smaller focal spots to improve imaging geometry. Magnification techniques, especially the spot-film technique, yields clearer delineation of high-contrast microcalcifications. Dedicated mammographic equipment with specially designed x-ray tubes is necessary for modern high-quality mammography. However, in many modern mammographic units, the automatic exposure controller still fails to provide appropriate and constant optical film density over a wide range of tissue thickness and absorption. Extended-cycle processing of single-emulsion mammographic films can yield better image contrast and reduce exposure by up to 30%. Exposure times of less than 1 second are recommended to avoid the unnecessary higher doses caused by longer exposure times and reciprocity law failure. The wide dynamic range in mammography can be reduced by a beam equalization filter, and thus be better adapted to the decreased latitude of modern high-contrast mammographic screen-film systems. Mammographic film reading (detection of subtle microcalcifications) can be facilitated by modern computer evaluation of previously digitized mammograms. Standardization and assurance of image quality have been major challenges in the technical development of mammography. Different technical and anthropomorphic phantoms have been designed to measure and compare practical image quality. Detailed quality control measures have been developed. The benefit of a single or annual screening mammography, calculated in gained life expectancy, by far outweighs the relative risk for radiation-induced breast cancer. 22 references.

  6. Environmental quality control report. [Semiannual] report, July--December 1988

    SciTech Connect

    Bishop, C.T.

    1989-04-14

    This report presents the details of the Mound Laboratory EPA-NPDES Quality Assurance Program, the DOE Quality Assessment Program Results, Proficiency Environmental Testing Program and Plutonium in Urine Quality Control for 1988.

  7. Protein Quality Control and Degradation in Cardiomyocytes

    PubMed Central

    Wang, Xuejun; Su, Huabo; Ranek, Mark J.

    2008-01-01

    The heart is constantly under stress and cardiomyocytes face enormous challenges to correctly fold nascent polypeptides and keep mature proteins from denaturing. To meet the challenge, cardiomyocytes have developed multi-layered protein quality control (PQC) mechanisms which are carried out primarily by chaperones and ubiquitin-proteasome system mediated proteolysis. Autophagy may also participate in PQC in cardiomyocytes, especially under pathological conditions. Cardiac PQC often becomes inadequate in heart disease, which may play an important role in the development of congestive heart failure. PMID:18495153

  8. Distributed Sensor Architecture for Intelligent Control that Supports Quality of Control and Quality of Service

    PubMed Central

    Poza-Lujan, Jose-Luis; Posadas-Yagüe, Juan-Luis; Simó-Ten, José-Enrique; Simarro, Raúl; Benet, Ginés

    2015-01-01

    This paper is part of a study of intelligent architectures for distributed control and communications systems. The study focuses on optimizing control systems by evaluating the performance of middleware through quality of service (QoS) parameters and the optimization of control using Quality of Control (QoC) parameters. The main aim of this work is to study, design, develop, and evaluate a distributed control architecture based on the Data-Distribution Service for Real-Time Systems (DDS) communication standard as proposed by the Object Management Group (OMG). As a result of the study, an architecture called Frame-Sensor-Adapter to Control (FSACtrl) has been developed. FSACtrl provides a model to implement an intelligent distributed Event-Based Control (EBC) system with support to measure QoS and QoC parameters. The novelty consists of using, simultaneously, the measured QoS and QoC parameters to make decisions about the control action with a new method called Event Based Quality Integral Cycle. To validate the architecture, the first five Braitenberg vehicles have been implemented using the FSACtrl architecture. The experimental outcomes, demonstrate the convenience of using jointly QoS and QoC parameters in distributed control systems. PMID:25723145

  9. 7 CFR 58.141 - Alternate quality control program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Alternate quality control program. 58.141 Section 58... Service 1 Quality Specifications for Raw Milk § 58.141 Alternate quality control program. When a plant has in operation an acceptable quality program, at the producer level, which is approved by...

  10. 7 CFR 58.141 - Alternate quality control program.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Alternate quality control program. 58.141 Section 58... Service 1 Quality Specifications for Raw Milk § 58.141 Alternate quality control program. When a plant has in operation an acceptable quality program, at the producer level, which is approved by...

  11. Quality Control, Quality Assurance, and Quality Improvement-What is the Difference and Why Should Compounding Pharmacies Care?

    PubMed

    Cabaleiro, Joe

    2009-01-01

    This article provides scenarios of three different pharmacies in the areas of quality control, quality assurance, and quality improvement. The scenarios show the importance that each pharmacy placed on a problem of dented capsules and the potential impact that an unresolved problem can have on a compounding pharmacy's business. Although this article focuses on one particular procedure, the purpose of th article is to help pharmacists understand the differences between quality control, quality assurance, and quality improvement. PMID:23966522

  12. Data quality control of ADSN Broadband stations

    NASA Astrophysics Data System (ADS)

    Alili, Azouaou; Yelles-chaouche, Abd el karim; Allili, Toufik; Messemen, Walid

    2014-05-01

    In this work we present the analysis of continuous waveform of the Algerian digital seismic network recorded during five years from 2008 to 2013 for twenty broadband stations using the power spectral densities (PSDs) and their corresponding probability density functions (PDFs) algorithm of McNamara, and Buland (2004). ADSN Broadband stations data quality is one main concern and interest of ADSN technical team. Indeed, the quality of the data from broadband stations is continuously controlled in quasi-realtime using "PQLX" (Pascal Quick Look eXtended) software to compute the PDFs and PSDs during the operation of the stations at different frequency range. At each station the level of noise is shown, which we can see diurnal and seasonal variation. From the data analysis, most of the ADSN Broadband stations display good records in the several frequency domains in relation with their site installation. However some of stations near the urban areas could present some noisy disturbances. This led sometimes to generate some ghost events. In the low frequency, some stations could be still influenced by the temperature variations. This long period of records from 2008 to 2013, led us to analyze and control the several stations year by year taking into account the seasons and to know about their work during five years. This analysis is also very important to improve in the future quality of station installation and choose the optimal station design in aim to reduce cultural noise and large fluctuation of temperature and pressure. Key words: PQLX, PDFs, PSDs, Broad Band

  13. 46 CFR 164.019-13 - Production quality control requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 6 2013-10-01 2013-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production,...

  14. 46 CFR 164.019-13 - Production quality control requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 6 2014-10-01 2014-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production,...

  15. 46 CFR 164.019-13 - Production quality control requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production,...

  16. 14 CFR 145.211 - Quality control system.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable...

  17. 21 CFR 640.56 - Quality control test for potency.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Quality control test for potency. 640.56 Section...) BIOLOGICS ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Cryoprecipitate § 640.56 Quality control test for potency. (a) Quality control tests for potency of antihemophilic factor shall be...

  18. 21 CFR 640.56 - Quality control test for potency.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 7 2011-04-01 2010-04-01 true Quality control test for potency. 640.56 Section...) BIOLOGICS ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Cryoprecipitate § 640.56 Quality control test for potency. (a) Quality control tests for potency of antihemophilic factor shall be...

  19. 14 CFR 145.211 - Quality control system.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Quality control system. 145.211 Section 145...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable...

  20. 46 CFR 164.019-13 - Production quality control requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 6 2011-10-01 2011-10-01 false Production quality control requirements. 164.019-13....019-13 Production quality control requirements. (a) General. Each component manufacturer shall establish procedures for maintaining quality control of the materials used in production,...

  1. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Quality assurance and quality control... PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Operation and Maintenance Requirements § 75.21 Quality assurance and quality control requirements. (a) Continuous emission monitoring systems. The owner...

  2. [Evaluating an internal quality control procedure: application to multidimensional control].

    PubMed

    Marquis, P; Masseyeff, R

    2002-01-01

    Internal quality control keeps in constant evolution in the industrial world. Introducing in clinical chemistry new QC methods derived from the industrial practice raises the point of the means for their evaluation. The main evaluation criteria are discussed in this paper. The importance of ARL (average run length) as a key-criterion of the efficiency of a quality control procedure is stressed. These principles were applied to the multivariate approach of multilevel control with the Hotelling's T2. This method led to a better detection of random errors than the independently managed conventional Shewhart (Levey- Jennings) charts. Applied to systematic errors, both methods gave similar results with a certain lack of sensitivity. However the multivariate method can be sensitised using EWMA (exponentially weighted moving average), a method specific for improved bias detection. EWMA efficiency outperforms that of the older systems of rules. Moreover, in any kind of error, multivariate approach secures a well-defined false rejection rate, whereas this rate is dependant on unknown inter-level correlation coefficients in conventional QC. PMID:12368148

  3. Intelligent process quality control system into supply chain

    NASA Astrophysics Data System (ADS)

    Wang, Shijie; Jiang, Xingyu; Wang, Yingchun

    2010-01-01

    To cope with the challenges of monitoring dynamic and variable quality variation into supply chain, diagnosing the abnormal variation at the right moment, is a difficult problem that a enterprise in supply chain faces in process quality control. An intelligent process quality control mode into supply chain, which integrated quality prevention, analysis, diagnosis and adjustment, and corresponding functional modules and framework were all put forward. This mode dealt mainly with constructing and running intelligent quality control system, such as the theory of similarity manufacturing, Statistical Process Control (SPC), neural network. Furthermore, some key enabling technologies were studied in detail, including process quality analysis on-line based on similarity process and process quality diagnosis based on Elman and expert system of process quality adjustment. It is basis of realizing network, intelligent and automatic process quality control into supply.

  4. Intelligent process quality control system into supply chain

    NASA Astrophysics Data System (ADS)

    Wang, Shijie; Jiang, Xingyu; Wang, Yingchun

    2009-12-01

    To cope with the challenges of monitoring dynamic and variable quality variation into supply chain, diagnosing the abnormal variation at the right moment, is a difficult problem that a enterprise in supply chain faces in process quality control. An intelligent process quality control mode into supply chain, which integrated quality prevention, analysis, diagnosis and adjustment, and corresponding functional modules and framework were all put forward. This mode dealt mainly with constructing and running intelligent quality control system, such as the theory of similarity manufacturing, Statistical Process Control (SPC), neural network. Furthermore, some key enabling technologies were studied in detail, including process quality analysis on-line based on similarity process and process quality diagnosis based on Elman and expert system of process quality adjustment. It is basis of realizing network, intelligent and automatic process quality control into supply.

  5. Quality assurance and quality control of geochemical data—A primer for the research scientist

    USGS Publications Warehouse

    Geboy, Nicholas J.; Engle, Mark A.

    2011-01-01

    Geochemistry is a constantly expanding science. More and more, scientists are employing geochemical tools to help answer questions about the Earth and earth system processes. Scientists may assume that the responsibility of examining and assessing the quality of the geochemical data they generate is not theirs but rather that of the analytical laboratories to which their samples have been submitted. This assumption may be partially based on knowledge about internal and external quality assurance and quality control (QA/QC) programs in which analytical laboratories typically participate. Or there may be a perceived lack of time or resources to adequately examine data quality. Regardless of the reason, the lack of QA/QC protocols can lead to the generation and publication of erroneous data. Because the interpretations drawn from the data are primary products to U.S. Geological Survey (USGS) stakeholders, the consequences of publishing erroneous results can be significant. The principal investigator of a scientific study ultimately is responsible for the quality and interpretation of the project's findings, and thus must also play a role in the understanding, implementation, and presentation of QA/QC information about the data. Although occasionally ignored, QA/QC protocols apply not only to procedures in the laboratory but also in the initial planning of a research study and throughout the life of the project. Many of the tenets of developing a sound QA/QC program or protocols also parallel the core concepts of developing a good study: What is the main objective of the study? Will the methods selected provide data of enough resolution to answer the hypothesis? How should samples be collected? Are there known or unknown artifacts or contamination sources in the sampling and analysis methods? Assessing data quality requires communication between the scientists responsible for designing the study and those collecting samples, analyzing samples, treating data, and

  6. Tools for quality control of fingerprint databases

    NASA Astrophysics Data System (ADS)

    Swann, B. Scott; Libert, John M.; Lepley, Margaret A.

    2010-04-01

    Integrity of fingerprint data is essential to biometric and forensic applications. Accordingly, the FBI's Criminal Justice Information Services (CJIS) Division has sponsored development of software tools to facilitate quality control functions relative to maintaining its fingerprint data assets inherent to the Integrated Automated Fingerprint Identification System (IAFIS) and Next Generation Identification (NGI). This paper provides an introduction of two such tools. The first FBI-sponsored tool was developed by the National Institute of Standards and Technology (NIST) and examines and detects the spectral signature of the ridge-flow structure characteristic of friction ridge skin. The Spectral Image Validation/Verification (SIVV) utility differentiates fingerprints from non-fingerprints, including blank frames or segmentation failures erroneously included in data; provides a "first look" at image quality; and can identify anomalies in sample rates of scanned images. The SIVV utility might detect errors in individual 10-print fingerprints inaccurately segmented from the flat, multi-finger image acquired by one of the automated collection systems increasing in availability and usage. In such cases, the lost fingerprint can be recovered by re-segmentation from the now compressed multi-finger image record. The second FBI-sponsored tool, CropCoeff was developed by MITRE and thoroughly tested via NIST. CropCoeff enables cropping of the replacement single print directly from the compressed data file, thus avoiding decompression and recompression of images that might degrade fingerprint features necessary for matching.

  7. mRNA quality control goes transcriptional

    PubMed Central

    Kilchert, Cornelia; Vasiljeva, Lidia

    2013-01-01

    Eukaryotic mRNAs are extensively processed to generate functional transcripts, which are 5′ capped, spliced and 3′ polyadenylated. Accumulation of unprocessed (aberrant) mRNAs can be deleterious for the cell, hence processing fidelity is closely monitored by QC (quality control) mechanisms that identify erroneous transcripts and initiate their selective removal. Nucleases including Xrn2/Rat1 and the nuclear exosome have been shown to play an important role in the turnover of aberrant mRNAs. Recently, with the growing appreciation that mRNA processing occurs concomitantly with polII (RNA polymerase II) transcription, it has become evident that QC acts at the transcriptional level in addition to degrading aberrant RNAs. In the present review, we discuss mechanisms that allow cells to co-transcriptionally initiate the removal of RNAs as well as down-regulate transcription of transcripts where processing repeatedly fails. PMID:24256272

  8. Quality control in the "flash" process.

    PubMed

    1985-03-01

    This article has briefly discussed the three basic types of sterilization monitoring systems--mechanical, chemical, and biological. Mechanical indicators help tell you that the sterilizer is working. Chemical indicators provide you with immediate information in each "flash" load that the conditions necessary for steam sterilization were present. Biological indicators tell you that microorganisms were killed. For maximum assurance that the conditions necessary for steam sterilization are present and that non-sterile instruments are not inadvertently used, each "flash" sterilizer should be monitored daily with biological indicators and each "flash" load with chemical indicators. This quality control monitoring program should give the O.R. staff confidence that their "flash" sterilization process is working. PMID:10271096

  9. Mitochondrial Quality Control as a Therapeutic Target.

    PubMed

    Suliman, Hagir B; Piantadosi, Claude A

    2016-01-01

    In addition to oxidative phosphorylation (OXPHOS), mitochondria perform other functions such as heme biosynthesis and oxygen sensing and mediate calcium homeostasis, cell growth, and cell death. They participate in cell communication and regulation of inflammation and are important considerations in aging, drug toxicity, and pathogenesis. The cell's capacity to maintain its mitochondria involves intramitochondrial processes, such as heme and protein turnover, and those involving entire organelles, such as fusion, fission, selective mitochondrial macroautophagy (mitophagy), and mitochondrial biogenesis. The integration of these processes exemplifies mitochondrial quality control (QC), which is also important in cellular disorders ranging from primary mitochondrial genetic diseases to those that involve mitochondria secondarily, such as neurodegenerative, cardiovascular, inflammatory, and metabolic syndromes. Consequently, mitochondrial biology represents a potentially useful, but relatively unexploited area of therapeutic innovation. In patients with genetic OXPHOS disorders, the largest group of inborn errors of metabolism, effective therapies, apart from symptomatic and nutritional measures, are largely lacking. Moreover, the genetic and biochemical heterogeneity of these states is remarkably similar to those of certain acquired diseases characterized by metabolic and oxidative stress and displaying wide variability. This biologic variability reflects cell-specific and repair processes that complicate rational pharmacological approaches to both primary and secondary mitochondrial disorders. However, emerging concepts of mitochondrial turnover and dynamics along with new mitochondrial disease models are providing opportunities to develop and evaluate mitochondrial QC-based therapies. The goals of such therapies extend beyond amelioration of energy insufficiency and tissue loss and entail cell repair, cell replacement, and the prevention of fibrosis. This review

  10. Chapter 5: Quality assurance/quality control in stormwater sampling

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Sampling the quality of stormwater presents unique challenges because stormwater flow is relatively short-lived with drastic variability. Furthermore, storm events often occur with little advance warning, outside conventional work hours, and under adverse weather conditions. Therefore, most stormwat...

  11. 21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for equipment, instruments, and controls? 111.117 Section 111.117 Food and Drugs FOOD AND DRUG ADMINISTRATION... and Process Control System: Requirements for Quality Control § 111.117 What quality control...

  12. 21 CFR 111.117 - What quality control operations are required for equipment, instruments, and controls?

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 2 2012-04-01 2012-04-01 false What quality control operations are required for equipment, instruments, and controls? 111.117 Section 111.117 Food and Drugs FOOD AND DRUG ADMINISTRATION... and Process Control System: Requirements for Quality Control § 111.117 What quality control...

  13. Quality-controlled Subject Gateways: Definitions, Typologies, Empirical Overview.

    ERIC Educational Resources Information Center

    Koch, Traugott

    2000-01-01

    "Quality-controlled subject gateways" are Internet services which apply quality measures to support systematic resource discovery. A main goal is to provide high quality subject access through indexing resources using controlled vocabularies and by offering a deep classification structure for advanced searching and browsing. Provides an empirical…

  14. 30 CFR 28.31 - Quality control plans; contents.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING SHORT-CIRCUIT...) Each quality control plan shall contain provisions for the management of quality, including: (1... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Quality control plans; contents. 28.31...

  15. 30 CFR 28.31 - Quality control plans; contents.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING SHORT-CIRCUIT...) Each quality control plan shall contain provisions for the management of quality, including: (1... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Quality control plans; contents. 28.31...

  16. 75 FR 41874 - Quality Control for Rental Assistance Subsidy Determinations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-19

    ... URBAN DEVELOPMENT Quality Control for Rental Assistance Subsidy Determinations AGENCY: Office of the... agency's estimate of the burden of the proposed collection of information; (3) Enhance the quality.... This notice also lists the following information: Title of Proposal: Quality Control for...

  17. 14 CFR 21.147 - Changes in quality control system.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Changes in quality control system. 21.147 Section 21.147 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... quality control system. After the issue of a production certificate, each change to the quality...

  18. 14 CFR 21.147 - Changes in quality control system.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Changes in quality control system. 21.147 Section 21.147 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... quality control system. After the issue of a production certificate, each change to the quality...

  19. 40 CFR 716.25 - Adequate file search.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Adequate file search. 716.25 Section 716.25 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT HEALTH AND SAFETY DATA REPORTING General Provisions § 716.25 Adequate file search. The scope of...

  20. Nuclear fuel pellet quality control using artificial intelligence techniques

    NASA Astrophysics Data System (ADS)

    Song, Xiaolong

    Inspection of nuclear fuel pellets is a complex and time-consuming process. At present, quality control in the fuel fabrication field mainly relies on human manual inspection, which is essentially a judgement call. Considering the high quality requirement of fuel pellets in the nuclear industry, pellet inspection systems must have a high accuracy rate in addition to a high inspection speed. Furthermore, any inspection process should have a low rejection rate of good pellets from the manufacturer point of view. It is very difficult to use traditional techniques, such as simple image comparison, to adequately perform the inspection process of the nuclear fuel pellet. Knowledge-based inspection and a defect-recognition algorithm, which maps the human inspection knowledge, is more robust and effective. A novel method is introduced here for pellet image processing. Three artificial intelligence techniques are studied and applied for fuel pellet inspection in this research. They are an artificial neural network, fuzzy logic, and the decision tree method. A dynamic reference model is located on each input fuel pellet image. Then, those pixels that belong to the abnormal defect are enhanced with high speed and high accuracy. Next, the content-based features for the defect are extracted from those abno1mal pixels and used in the inspection algorithm. Finally, an automated inspection prototype system---Visual Inspection Studio---which combines machine vision and these three AI techniques, is developed and tested. The experimental results indicate a very successful system with a high potential for on-line automatic inspection process.

  1. Quality assurance standards for purchasing and inventory control.

    PubMed

    Soares, D P

    1985-03-01

    A process is described for quality assurance in pharmaceutical purchasing and inventory control. A quality assurance program should ensure that quality drugs are purchased at the lowest price, drug products are available when needed, the system is managed efficiently, internal controls are provided, drug products are stored under appropriate conditions, and laws, regulations, accreditation standards, and procedures are followed. To meet these objectives, product quality, vendor performance, the department's system of internal controls, purchasing data, and storage conditions should be monitored. A checklist for evaluating purchasing and inventory practices and a sample audit form listing quality assurance criteria, standards, procedures, and recommended actions are provided. A quality assurance program for pharmaceutical purchasing and inventory control should define institution-specific criteria and standards and use these standards for continual evaluation of all aspects of the purchasing and inventory control system. Documentation of quality assurance activities should be provided for use by the purchasing department, hospital administration, and regulatory bodies. PMID:3985026

  2. Novel topical formulation for ischemic chronic wounds. Technological design, quality control and safety evaluation.

    PubMed

    Cabrera, Carla Agostina; Ramos, Alberto Nicolas; Loandos, María Del Huerto; Valdez, Juan Carlos; Sesto Cabral, Maria Eugenia

    2016-06-01

    Ulceration of the foot in diabetes is common and disabling, and frequently leads to amputation of the leg. The pathogenesis of foot ulceration is complex, clinical presentation variable and management requires early expert assessment. Despite treatment, ulcers readily become chronic wounds. Chronic wounds are those that remain in a chronic inflammatory state failing a normal healing process patterns. This is partially caused by inefficient eradication of opportunistic pathogens like Pseudomonas aeruginosa. We propose its control or eradication will promote wound healing. Lactobacillus plantarum cultures supernatants (LAPS) shows antipathogenic and pro-healing properties. The main objective was to design two pharmaceutical dosage forms by using LAPS as active pharmaceutical ingredient and to perform its quality control, in vitro activity conservation tests and human trials (safety evaluation). Both selected formulations reach the technological quality expected for 120 days, shows adequate occlusive characteristics and proper adhesion to human skin. From the in vitro release assays were found that LAPS shows adequate release from matrix and maintain its antimicrobial and anti-biofilm activity. First human trials were developed and neither edema nor erythema on healthy skin voluntaries was found. We conclude that C80 and C100 are adequate for their use in future clinical trials to demonstrate a comprehensive therapeutic effectiveness in ischemic chronic wounds. PMID:25687423

  3. Timing control improves seabed survey data quality

    SciTech Connect

    Green, R.

    1996-04-01

    Seateam has completed development of and field-proven the Dolphin data acquisition and timing system for high-density surveys offshore. The Dolphin project was initiated to improve quality control of survey sensor data and ensure time synchronization, thus leading to faster turnaround of seabed terrain information. Data received from survey sensors is asynchronous, so the system must provide for data correlation. This includes establishment of data latency, i.e., the time difference between data creation and timing of the message at first-byte arrival at the recording system. Until recently, asynchronous data from multiple sensors was collected by a single computer, regardless of whether it had additional intelligent or non-intelligent serial cards. This computer was fully responsible for time stamping all incoming data, plus associated storage and distribution. Though this initially sufficed and is still applicable to low-density data, increasingly larger data volumes required an associated boost in the capability to time stamp data prior to eventual correction.

  4. Mitochondrial Quality Control and Muscle Mass Maintenance

    PubMed Central

    Romanello, Vanina; Sandri, Marco

    2016-01-01

    Loss of muscle mass and force occurs in many diseases such as disuse/inactivity, diabetes, cancer, renal, and cardiac failure and in aging-sarcopenia. In these catabolic conditions the mitochondrial content, morphology and function are greatly affected. The changes of mitochondrial network influence the production of reactive oxygen species (ROS) that play an important role in muscle function. Moreover, dysfunctional mitochondria trigger catabolic signaling pathways which feed-forward to the nucleus to promote the activation of muscle atrophy. Exercise, on the other hand, improves mitochondrial function by activating mitochondrial biogenesis and mitophagy, possibly playing an important part in the beneficial effects of physical activity in several diseases. Optimized mitochondrial function is strictly maintained by the coordinated activation of different mitochondrial quality control pathways. In this review we outline the current knowledge linking mitochondria-dependent signaling pathways to muscle homeostasis in aging and disease and the resulting implications for the development of novel therapeutic approaches to prevent muscle loss. PMID:26793123

  5. Quality Control of Diffusion Weighted Images

    PubMed Central

    Liu, Zhexing; Wang, Yi; Gerig, Guido; Gouttard, Sylvain; Tao, Ran; Fletcher, Thomas; Styner, Martin

    2013-01-01

    Diffusion Tensor Imaging (DTI) has become an important MRI procedure to investigate the integrity of white matter in brain in vivo. DTI is estimated from a series of acquired Diffusion Weighted Imaging (DWI) volumes. DWI data suffers from inherent low SNR, overall long scanning time of multiple directional encoding with correspondingly large risk to encounter several kinds of artifacts. These artifacts can be too severe for a correct and stable estimation of the diffusion tensor. Thus, a quality control (QC) procedure is absolutely necessary for DTI studies. Currently, routine DTI QC procedures are conducted manually by visually checking the DWI data set in a gradient by gradient and slice by slice way. The results often suffer from low consistence across different data sets, lack of agreement of different experts, and difficulty to judge motion artifacts by qualitative inspection. Additionally considerable manpower is needed for this step due to the large number of images to QC, which is common for group comparison and longitudinal studies, especially with increasing number of diffusion gradient directions. We present a framework for automatic DWI QC. We developed a tool called DTIPrep which pipelines the QC steps with a detailed protocoling and reporting facility. And it is fully open source. This framework/tool has been successfully applied to several DTI studies with several hundred DWIs in our lab as well as collaborating labs in Utah and Iowa. In our studies, the tool provides a crucial piece for robust DTI analysis in brain white matter study. PMID:24353379

  6. Quality control and reliability of reported doses.

    PubMed

    Stadtmann, H; Figel, Markus; Kamenopoulou, V; Kluszczynski, D; Roed, H; Van Dijk, J

    2004-01-01

    Results of performance tests verifying the dosimetric properties of dosimetric systems are published in various reports (e.g. IAEA and EURADOS). However, there is hardly any information in the open literature relating to the uncertainty in a dose measurement or in the annual dose, which is increased by failure of the evaluation or data management system, damage of the dosemeter itself or by the loss of dosemeter. In this article, an attempt is made to estimate the importance of the above-mentioned conditions. This is achieved by sending questionnaires to about 200 approved dosimetric services in Europe. In total 88 questionnaires were returned and analysed. In the questionnaires, the frequency of occurrence of the various error conditions were investigated. Participants were also asked to evaluate the impact of the error condition from a dosimetric point of view and what countermeasures are taken. The article summarises all responses and compares different sources of errors according to their impact on the uncertainty of the resulting dose and gives a comprehensive overview on quality control actions and reliability on reported doses from European dosimetric services. PMID:15574990

  7. Toward standardising gamma camera quality control procedures

    NASA Astrophysics Data System (ADS)

    Alkhorayef, M. A.; Alnaaimi, M. A.; Alduaij, M. A.; Mohamed, M. O.; Ibahim, S. Y.; Alkandari, F. A.; Bradley, D. A.

    2015-11-01

    Attaining high standards of efficiency and reliability in the practice of nuclear medicine requires appropriate quality control (QC) programs. For instance, the regular evaluation and comparison of extrinsic and intrinsic flood-field uniformity enables the quick correction of many gamma camera problems. Whereas QC tests for uniformity are usually performed by exposing the gamma camera crystal to a uniform flux of gamma radiation from a source of known activity, such protocols can vary significantly. Thus, there is a need for optimization and standardization, in part to allow direct comparison between gamma cameras from different vendors. In the present study, intrinsic uniformity was examined as a function of source distance, source activity, source volume and number of counts. The extrinsic uniformity and spatial resolution were also examined. Proper standard QC procedures need to be implemented because of the continual development of nuclear medicine imaging technology and the rapid expansion and increasing complexity of hybrid imaging system data. The present work seeks to promote a set of standard testing procedures to contribute to the delivery of safe and effective nuclear medicine services.

  8. 29 CFR 98.900 - Adequate evidence.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Adequate evidence. 98.900 Section 98.900 Labor Office of the Secretary of Labor GOVERNMENTWIDE DEBARMENT AND SUSPENSION (NONPROCUREMENT) Definitions § 98.900 Adequate evidence. Adequate evidence means information sufficient to support the reasonable belief that a...

  9. 42 CFR 84.256 - Quality control requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in...

  10. 42 CFR 84.256 - Quality control requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 1 2011-10-01 2011-10-01 false Quality control requirements. 84.256 Section 84.256... § 84.256 Quality control requirements. (a) In addition to the construction and performance requirements specified in §§ 84.251, 84.252, 84.253, 84.254, and 84.255, the quality control requirements in...

  11. TECHNICAL GUIDANCE DOCUMENT: QUALITY ASSURANCE AND QUALITY CONTROL FOR WASTE CONTAINMENT FACILITIES

    EPA Science Inventory

    This Technical Guidance Document provides comprehensive guidance on procedures for quality assurance and quality control for waste containment facilities. he document includes a discussion of principles and concepts, compacted soil liners, soil drainage systems, geosynthetic drai...

  12. TECHNICAL GUIDANCE DOCUMENT: QUALITY ASSURANCE AND QUALITY CONTROL FOR WASTE CONTAINMENT FACILITIES

    EPA Science Inventory

    This Technical Guidance Document provides comprehensive guidance on procedures for quality assurance and quality control for waste containment facilities. The document includes a discussion of principles and concepts, compacted soil liners, soil drainage systems, geosynthetic dr...

  13. Proteomics Quality Control: Quality Control Software for MaxQuant Results.

    PubMed

    Bielow, Chris; Mastrobuoni, Guido; Kempa, Stefan

    2016-03-01

    Mass spectrometry-based proteomics coupled to liquid chromatography has matured into an automatized, high-throughput technology, producing data on the scale of multiple gigabytes per instrument per day. Consequently, an automated quality control (QC) and quality analysis (QA) capable of detecting measurement bias, verifying consistency, and avoiding propagation of error is paramount for instrument operators and scientists in charge of downstream analysis. We have developed an R-based QC pipeline called Proteomics Quality Control (PTXQC) for bottom-up LC-MS data generated by the MaxQuant1 software pipeline. PTXQC creates a QC report containing a comprehensive and powerful set of QC metrics, augmented with automated scoring functions. The automated scores are collated to create an overview heatmap at the beginning of the report, giving valuable guidance also to nonspecialists. Our software supports a wide range of experimental designs, including stable isotope labeling by amino acids in cell culture (SILAC), tandem mass tags (TMT), and label-free data. Furthermore, we introduce new metrics to score MaxQuant's Match-between-runs (MBR) functionality by which peptide identifications can be transferred across Raw files based on accurate retention time and m/z. Last but not least, PTXQC is easy to install and use and represents the first QC software capable of processing MaxQuant result tables. PTXQC is freely available at https://github.com/cbielow/PTXQC . PMID:26653327

  14. International Quality Control Is No Easy Task

    ERIC Educational Resources Information Center

    Contreras, Alan

    2008-01-01

    In early March, the European Quality Assurance Register for Higher Education was established under what is called the Bologna Process. The 46 countries involved in the process seek to improve the quality and assessment of higher education throughout Europe, thus facilitating students' mobility among institutions and countries and enhancing…

  15. Technology to control variation in meat quality

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Consumers have certain expectations regarding the quality of the meat they purchase. Lean color is the primary quality attribute used by consumers to make purchase decisions. Similarly, repeat purchase decisions are generally a result of eating satisfaction, which is determined by the perceived va...

  16. Integrated Quality Control Measurement Project. Findings and Corrective Actions.

    ERIC Educational Resources Information Center

    Price Waterhouse and Co., New York, NY.

    The Integrated Quality Control Measurement Project (IQCMP) of the U.S. Department of Education measured the quality of awards distributed during the 1988-89 award year under the three major Title IV programs: the Pell Grant program, the Campus-Based programs, and the Stafford Loan program, in order to evaluate and improve the quality of the…

  17. Food and Nutrition Services Quality Control Management Program.

    ERIC Educational Resources Information Center

    Wimsatt-Fraim, Teresa S.

    A program was conducted to improve the quality of food service through the training of 44 food and nutrition service employees in a 200-bed hospital. A 12-week quality control program was implemented to address four key areas: food temperatures, food accuracy, food quality, and dietary personnel. Learning strategies, emphasizing critical thinking…

  18. Teaching Quality Control with Chocolate Chip Cookies

    ERIC Educational Resources Information Center

    Baker, Ardith

    2014-01-01

    Chocolate chip cookies are used to illustrate the importance and effectiveness of control charts in Statistical Process Control. By counting the number of chocolate chips, creating the spreadsheet, calculating the control limits and graphing the control charts, the student becomes actively engaged in the learning process. In addition, examining…

  19. Space Shuttle flying qualities and flight control system assessment study

    NASA Technical Reports Server (NTRS)

    Myers, T. T.; Johnston, D. E.; Mcruer, D.

    1982-01-01

    The suitability of existing and proposed flying quality and flight control system criteria for application to the space shuttle orbiter during atmospheric flight phases was assessed. An orbiter experiment for flying qualities and flight control system design criteria is discussed. Orbiter longitudinal and lateral-directional flying characteristics, flight control system lag and time delay considerations, and flight control manipulator characteristics are included. Data obtained from conventional aircraft may be inappropriate for application to the shuttle orbiter.

  20. 46 CFR 164.019-13 - Production quality control requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Production quality control requirements. 164.019-13 Section 164.019-13 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Personal Flotation Device Components § 164.019-13 Production quality control...

  1. 14 CFR 145.211 - Quality control system.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to the FAA that ensures the airworthiness of the articles on which the repair station or any of...

  2. 14 CFR 145.211 - Quality control system.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to the FAA that ensures the airworthiness of the articles on which the repair station or any of...

  3. 14 CFR 145.211 - Quality control system.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ...) SCHOOLS AND OTHER CERTIFICATED AGENCIES REPAIR STATIONS Operating Rules § 145.211 Quality control system. (a) A certificated repair station must establish and maintain a quality control system acceptable to the FAA that ensures the airworthiness of the articles on which the repair station or any of...

  4. Quality Control Study of the GSL Reinsurance System. Final Report.

    ERIC Educational Resources Information Center

    Advanced Technology, Inc., Reston, VA.

    A quality control plan for the U.S. Department of Education's Guaranteed Student Loan (GSL) reinsurance process was developed. To identify existing errors, systems documentation and past analyses of the reinsurance system were analyzed, and interviews were conducted. Corrective actions were proposed, and a quality control checklist was developed…

  5. 7 CFR 58.442 - Laboratory and quality control tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Laboratory and quality control tests. 58.442 Section 58.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Operations and Operating Procedures § 58.442 Laboratory and quality control tests. (a)...

  6. Building Science Corporation's Building America Quality Control Checklist

    SciTech Connect

    2008-10-05

    The Building America Quality Control Checklist has been developed as both a guide to assist in the transition to high performance home building, and as a simplified tool to be used as part of any builder's on-site quality control procedures.

  7. 7 CFR 58.442 - Laboratory and quality control tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Laboratory and quality control tests. 58.442 Section 58.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Operations and Operating Procedures § 58.442 Laboratory and quality control tests. (a)...

  8. 7 CFR 58.442 - Laboratory and quality control tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Laboratory and quality control tests. 58.442 Section 58.442 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Operations and Operating Procedures § 58.442 Laboratory and quality control tests. (a)...

  9. Artificial Intelligence Approach to Support Statistical Quality Control Teaching

    ERIC Educational Resources Information Center

    Reis, Marcelo Menezes; Paladini, Edson Pacheco; Khator, Suresh; Sommer, Willy Arno

    2006-01-01

    Statistical quality control--SQC (consisting of Statistical Process Control, Process Capability Studies, Acceptance Sampling and Design of Experiments) is a very important tool to obtain, maintain and improve the Quality level of goods and services produced by an organization. Despite its importance, and the fact that it is taught in technical and…

  10. 7 CFR 58.733 - Quality control tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.733 Section 58.733... Procedures § 58.733 Quality control tests. (a) Chemical analyses. The following chemical analyses shall be... pasteurization by means of the phosphatase test, as well as any other tests necessary to assure good...

  11. For and against a European quality control of training.

    PubMed

    Dimitrakakis, C; Michalas, S

    2001-01-01

    In a world of medicine that evolves more and more rapidly, sufficient quality of education in the arts and crafts of our discipline and control of this quality are essential for the progress and vitality of Ob/Gyn. There are variations in training within European countries but with the aim of harmonization in training programmes and the flexibility of quality control mechanisms we will meet our objective that is the high standards in the care of woman throughout Europe. PMID:11205701

  12. 40 CFR Appendix B to Part 75 - Quality Assurance and Quality Control Procedures

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Quality Assurance and Quality Control Procedures B Appendix B to Part 75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Pt. 75, App. B Appendix B to Part 75—Quality...

  13. Ride quality sensitivity to SAS control law and to handling quality variations

    NASA Technical Reports Server (NTRS)

    Roberts, P. A.; Schmidt, D. K.; Swaim, R. L.

    1976-01-01

    The RQ trends which large flexible aircraft exhibit under various parameterizations of control laws and handling qualities are discussed. A summary of the assumptions and solution technique, a control law parameterization review, a discussion of ride sensitivity to handling qualities, and the RQ effects generated by implementing relaxed static stability configurations are included.

  14. NIF Projects Controls and Information Systems Software Quality Assurance Plan

    SciTech Connect

    Fishler, B

    2011-03-18

    Quality achievement for the National Ignition Facility (NIF) and the National Ignition Campaign (NIC) is the responsibility of the NIF Projects line organization as described in the NIF and Photon Science Directorate Quality Assurance Plan (NIF QA Plan). This Software Quality Assurance Plan (SQAP) is subordinate to the NIF QA Plan and establishes quality assurance (QA) activities for the software subsystems within Controls and Information Systems (CIS). This SQAP implements an activity level software quality assurance plan for NIF Projects as required by the LLNL Institutional Software Quality Assurance Program (ISQAP). Planned QA activities help achieve, assess, and maintain appropriate quality of software developed and/or acquired for control systems, shot data systems, laser performance modeling systems, business applications, industrial control and safety systems, and information technology systems. The objective of this SQAP is to ensure that appropriate controls are developed and implemented for management planning, work execution, and quality assessment of the CIS organization's software activities. The CIS line organization places special QA emphasis on rigorous configuration control, change management, testing, and issue tracking to help achieve its quality goals.

  15. 34 CFR 85.900 - Adequate evidence.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) Definitions § 85.900 Adequate evidence. Adequate evidence means information sufficient to support the reasonable belief that a particular act or omission has occurred. Authority: E.O. 12549 (3 CFR, 1986 Comp., p. 189); E.O 12689 (3 CFR, 1989 Comp., p. 235); 20 U.S.C. 1082, 1094, 1221e-3 and 3474; and Sec....

  16. 29 CFR 452.110 - Adequate safeguards.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 2 2010-07-01 2010-07-01 false Adequate safeguards. 452.110 Section 452.110 Labor... DISCLOSURE ACT OF 1959 Election Procedures; Rights of Members § 452.110 Adequate safeguards. (a) In addition to the election safeguards discussed in this part, the Act contains a general mandate in section...

  17. 29 CFR 452.110 - Adequate safeguards.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 2 2011-07-01 2011-07-01 false Adequate safeguards. 452.110 Section 452.110 Labor... DISCLOSURE ACT OF 1959 Election Procedures; Rights of Members § 452.110 Adequate safeguards. (a) In addition to the election safeguards discussed in this part, the Act contains a general mandate in section...

  18. Supplemental Control for Aircraft Riding Qualities

    NASA Technical Reports Server (NTRS)

    Williams, Rolanda S.; Ashokkumar, C. R.; Homaifar, Abdollah

    1997-01-01

    The concept of preview control has been applied and proven to be successful in the automotive vehicle. These same concepts are now applied to an aircraft under the assumption that exogenous inputs (wind gust, turbulence, etc. ) can be measured. A supplemental control law for surface deflection is designed to compensate for the loss in performance in the presence of atmospheric disturbances. Fuzzy logic control is employed to handle the nonlinear, time varying characteristics of the disturbance. A methodology to tune the outer loop control parameters is presented.

  19. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SO2 monitoring system shall be considered out-of-control. The length of the out-of-control period..., non-quality-assured data for each disapproved system. (2) Out-of-control period. Whenever a continuous... other audit, the system is out-of-control. The owner or operator shall follow the procedures for...

  20. 40 CFR 75.21 - Quality assurance and quality control requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SO2 monitoring system shall be considered out-of-control. The length of the out-of-control period..., non-quality-assured data for each disapproved system. (2) Out-of-control period. Whenever a continuous... other audit, the system is out-of-control. The owner or operator shall follow the procedures for...

  1. Statistical process control for total quality

    NASA Astrophysics Data System (ADS)

    Ali, Syed W.

    1992-06-01

    The paper explains the techniques and applications of statistical process control (SPC). Examples of control charts used in the Poseidon program of the NASA ocean topography experiment (TOPEX) and a brief discussion of Taguchi methods are presented. It is noted that SPC involves everyone in process improvement by providing objective, workable data. It permits continuous improvement instead of merely aiming for all parts to be within a tolerance band.

  2. Web quality control for lectures: Supercourse and Amazon.com.

    PubMed

    Linkov, Faina; LaPorte, Ronald; Lovalekar, Mita; Dodani, Sunita

    2005-12-01

    Peer review has been at the corner stone of quality control of the biomedical journals in the past 300 years. With the emergency of the Internet, new models of quality control and peer review are emerging. However, such models are poorly investigated. We would argue that the popular system of quality control used in Amazon.com offers a way to ensure continuous quality improvement in the area of research communications on the Internet. Such system is providing an interesting alternative to the traditional peer review approaches used in the biomedical journals and challenges the traditional paradigms of scientific publishing. This idea is being explored in the context of Supercourse, a library of 2,350 prevention lectures, shared for free by faculty members from over 150 countries. Supercourse is successfully utilizing quality control approaches that are similar to Amazon.com model. Clearly, the existing approaches and emerging alternatives for quality control in scientific communications needs to be assessed scientifically. Rapid explosion of internet technologies could be leveraged to produce better, more cost effective systems for quality control in the biomedical publications and across all sciences. PMID:16342339

  3. Commonly Practiced Quality Control and Quality Assurance Procedures for Gas Chromatography-Mass Spectrometry Analysis in Forensic Urine Drug-Testing Laboratories.

    PubMed

    Goldberger, B A; Huestis, M A; Wilkins, D G

    1997-12-01

    Forensic urine drug-testing laboratories operate in a prescribed scientific and administrative manner to ensure accurate test results. All specimens positive by an initial immunoassay test must be confirmed by gas chromatography/mass spectrometry (GC/MS). To provide adequate control and verification of these analytical processes, laboratories must implement appropriate policies and procedures to be used in routine practice. This review describes the following topics regarding GC/MS analyses: method validation, instrument performance, assay calibration, quality control, criteria for designating a positive test result, sample and batch acceptance criteria, and GC/MS data review. PMID:26269941

  4. Achieving indoor air quality through contaminant control

    SciTech Connect

    Katzel, J.

    1995-07-10

    Federal laws outlining industry`s responsibilities in creating a healthy, hazard-free workspace are well known. OSHA`s laws on interior air pollution establish threshold limit values (TLVs) and permissible exposure limits (PELs) for more than 500 potentially hazardous substances found in manufacturing operations. Until now, OSHA has promulgated regulations only for the manufacturing environment. However, its recently-proposed indoor air quality (IAQ) ruling, if implemented, will apply to all workspaces. It regulates IAQ, including environmental tobacco smoke, and requires employers to write and implement IAQ compliance plans.

  5. Quality Control of Fungal and Viral Biocontrol Agents

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Constraints to the use of the “inundative” or “biopesticide” strategy of biological control include a lack of consistent pest control efficacy, short product shelf-life, and costly production and stabilization processes. Quality control measures that standardize the production, stabilization, formu...

  6. Mesh quality control for multiply-refined tetrahedral grids

    NASA Technical Reports Server (NTRS)

    Biswas, Rupak; Strawn, Roger

    1994-01-01

    A new algorithm for controlling the quality of multiply-refined tetrahedral meshes is presented in this paper. The basic dynamic mesh adaption procedure allows localized grid refinement and coarsening to efficiently capture aerodynamic flow features in computational fluid dynamics problems; however, repeated application of the procedure may significantly deteriorate the quality of the mesh. Results presented show the effectiveness of this mesh quality algorithm and its potential in the area of helicopter aerodynamics and acoustics.

  7. Academic Quality Control in Nigerian Universities: Exploring Lecturers' Perceptions

    ERIC Educational Resources Information Center

    Obiekezie, E. O.; Ejemot-Nwadiaro, R. I.; Essien, M. I.; Timothy, A. Essien

    2014-01-01

    The level of job performance, international comparability and competitiveness of Nigerian university graduates are burning issues. Consequently, the academic quality of Nigerian universities has come under severe criticism. Since university lecturers are key players in quality control in universities, this study explored their perceptions of…

  8. 30 CFR 28.31 - Quality control plans; contents.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 28.31 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING...) Each quality control plan shall contain provisions for the management of quality, including: (1... Specification MIL-F-15160D is available for examination at the U.S. Department of Labor, Mine Safety and...

  9. 30 CFR 28.31 - Quality control plans; contents.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28.31 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING...) Each quality control plan shall contain provisions for the management of quality, including: (1... Specification MIL-F-15160D is available for examination at the U.S. Department of Labor, Mine Safety and...

  10. 115. QUALITY CONTROL BOARD FOR MAINTENANCE AND INSPECTION AT SOUTH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    115. QUALITY CONTROL BOARD FOR MAINTENANCE AND INSPECTION AT SOUTH SIDE OF MECHANICAL AND ELECTRICAL ROOM (110), LSB (BLDG. 770), FACING WEST ON EXTERIOR WALL OF QUALITY ASSURANCE ROOM (106A) - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 West, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  11. 42 CFR 84.41 - Quality control plans; contents.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from DODSSP, Standardization... 42 Public Health 1 2010-10-01 2010-10-01 false Quality control plans; contents. 84.41 Section 84... AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Quality...

  12. A quality control program for waste disposal vault closure

    SciTech Connect

    Benny, H.L.

    1994-07-01

    This paper provides a review of the quality control program employed for closure for a radioactive waste disposal vault at Hanford Washington. The major elements of the program are discussed, as well as the testing results and lessons learned.

  13. Quality control system response to stochastic growth of amyloid fibrils.

    PubMed

    Pigolotti, Simone; Lizana, Ludvig; Otzen, Daniel; Sneppen, Kim

    2013-05-01

    We introduce a stochastic model describing aggregation of misfolded proteins and degradation by the protein quality control system in a single cell. Aggregate growth is contrasted by the cell quality control system, that attacks them at different stages of the growth process, with an efficiency that decreases with their size. Model parameters are estimated from experimental data. Two qualitatively different behaviors emerge: a homeostatic state, where the quality control system is stable and aggregates of large sizes are not formed, and an oscillatory state, where the quality control system periodically breaks down, allowing for formation of large aggregates. We discuss how these periodic breakdowns may constitute a mechanism for the development of neurodegenerative diseases. PMID:23524241

  14. VERIFICATION TESTING OF AIR POLLUTION CONTROL TECHNOLOGY QUALITY MANAGEMENT PLAN

    EPA Science Inventory

    This document is the basis for quality assurance for the Air Pollution Control Technology Verification Center (APCT Center) operated under the U.S. Environmental Protection Agency (EPA). It describes the policies, organizational structure, responsibilities, procedures, and qualit...

  15. 7 CFR 58.733 - Quality control tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Procedures § 58.733 Quality control tests. (a) Chemical analyses. The following chemical analyses shall be performed in accordance with the appropriate edition of the Official Methods of Analysis of the AOAC as... Cheese Products Bearing USDA Official Identification...

  16. Americans Getting Adequate Water Daily, CDC Finds

    MedlinePlus

    ... medlineplus/news/fullstory_158510.html Americans Getting Adequate Water Daily, CDC Finds Men take in an average ... new government report finds most are getting enough water each day. The data, from the U.S. National ...

  17. Americans Getting Adequate Water Daily, CDC Finds

    MedlinePlus

    ... gov/news/fullstory_158510.html Americans Getting Adequate Water Daily, CDC Finds Men take in an average ... new government report finds most are getting enough water each day. The data, from the U.S. National ...

  18. Development of Quality Control Procedures for Lepidoptera

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Lepidopteran species are among the most destructive insect pests throughout the world. The sterile insect technique (SIT), within an area-wide integrated pest management (AW-IPM) approach, has proven to be a valuable tactic for controlling and eradicating important moth pests. Improving laboratory...

  19. Experience with ISO quality control in assisted reproductive technology.

    PubMed

    Alper, Michael M

    2013-12-01

    Assisted reproductive technology (ART) programs are complex organizations requiring the integration of multiple disciplines. ISO 9001:2008 is a quality management system that is readily adaptable to an ART program. The value that ISO brings to the entire organization includes control of documents, clear delineation of responsibilities of staff members, documentation of the numerous processes and procedures, improvement in tracking and reducing errors, and overall better control of systems. A quality ART program sets quality objectives and monitors their progress. ISO provides a sense of transparency within the organization and clearer understanding of how service is provided to patients. Most importantly, ISO provides the framework to allow for continual improvement. PMID:24112531

  20. Quality control standards in PGD and PGS.

    PubMed

    SenGupta, S B; Dhanjal, S; Harper, J C

    2016-03-01

    Preimplantation genetic diagnosis (PGD) aims to test the embryo for specific conditions before implantation in couples at risk of transmitting genetic abnormality to their offspring. The couple must undergo IVF procedures to generate embryos in vitro. The embryos can be biopsied at either the zygote, cleavage or blastocyst stage. Preimplantation genetic screening uses the same technology to screen for chromosome abnormalities in embryos from patients undergoing IVF procedures as a method of embryo selection. Fluorescence in-situ hybridization was originally used for chromosome analysis, but has now been replaced by array comparative genomic hybridization or next generation sequencing. For the diagnosis of single gene defects, polymerase chain reaction is used and has become highly developed; however, single nucleotide polymorphism arrays for karyomapping have recently been introduced. A partnership between IVF laboratories and diagnostic centres is required to carry out PGD and preimplantation genetic screening. Accreditation of PGD diagnostic laboratories is important. Accreditation gives IVF centres an assurance that the diagnostic tests conform to specified standards. ISO 15189 is an international laboratory standard specific for medical laboratories. A requirement for accreditation is to participate in external quality assessment schemes. PMID:26776824

  1. Nuclear Technology Series. Course 14: Introduction to Quality Assurance/Quality Control.

    ERIC Educational Resources Information Center

    Technical Education Research Center, Waco, TX.

    This technical specialty course is one of thirty-five courses designed for use by two-year postsecondary institutions in five nuclear technician curriculum areas: (1) radiation protection technician, (2) nuclear instrumentation and control technician, (3) nuclear materials processing technician, (4) nuclear quality-assurance/quality-control…

  2. Quality Assurance and Quality Control Practices for Rehabilitation of Sewer and Water Mains

    EPA Science Inventory

    As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued, including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of reha...

  3. HANDBOOK: QUALITY ASSURANCE/QUALITY CONTROL (QA/QC) PROCEDURES FOR HAZARDOUS WASTE INCINERATION

    EPA Science Inventory

    Resource Conservation and Recovery Act regulations for hazardous waste incineration require trial burns by permit applicants. uality Assurance Project Plan (QAPjP) must accompany a trial burn plan with appropriate quality assurance/quality control procedures. uidance on the prepa...

  4. Development and Testing of a Nuclear Quality Assurance/Quality Control Technician Curriculum. Final Report.

    ERIC Educational Resources Information Center

    Espy, John; And Others

    A project was conducted to field test selected first- and second-year courses in a postsecondary nuclear quality assurance/quality control (QA/QC) technician curriculum and to develop the teaching/learning modules for seven technical specialty courses remaining in the QA/QC technician curriculum. The field testing phase of the project involved the…

  5. Quality Assurance and Quality Control Practices For Rehabilitation of Sewer and Water Mains

    EPA Science Inventory

    As part of the US Environmental Protection Agency (EPA)’s Aging Water Infrastructure Research Program, several areas of research are being pursued including a review of quality assurance and quality control (QA/QC) practices and acceptance testing during the installation of rehab...

  6. Quality control throughout the production process of infant food.

    PubMed

    Hamrin, Pia; Hoeft, Birgit

    2012-01-01

    The manufacture of infant food is a highly complex process and needs an effective quality control beyond classical in-process parameters and a final microbiological analysis. To ensure a safe end -product, various tools, such as the Hazard Analysis Critical Control Points (HACCP), have been developed to facilitate the management of food safety. Every single infant formula ingredient must have an excellent quality and safety approach because even if an ingredient is used in very small quantities in a single product, serious consequences may arise if the quality and product safety are not taken seriously by the ingredient manufacturer. The purpose of this article was twofold: firstly, to briefly describe existing Quality Management Systems and, secondly, to highlight the consequences of non-quality. PMID:22699770

  7. The process of managerial control in quality improvement initiatives.

    PubMed

    Slovensky, D J; Fottler, M D

    1994-11-01

    The fundamental intent of strategic management is to position an organization with in its market to exploit organizational competencies and strengths to gain competitive advantage. Competitive advantage may be achieved through such strategies as low cost, high quality, or unique services or products. For health care organizations accredited by the Joint Commission on Accreditation of Healthcare Organizations, continually improving both processes and outcomes of organizational performance--quality improvement--in all operational areas of the organization is a mandated strategy. Defining and measuring quality and controlling the quality improvement strategy remain problematic. The article discusses the nature and processes of managerial control, some potential measures of quality, and related information needs. PMID:10138526

  8. Research review: Indoor air quality control techniques

    SciTech Connect

    Fisk, W.J.

    1986-10-01

    Techniques for controlling the concentration of radon, formaldehyde, and combustion products in the indoor air are reviewed. The most effective techniques, which are generally based on limiting or reducing indoor pollutant source strengths, can decrease indoor pollutant concentrations by a factor of 3 to 10. Unless the initial ventilation rate is unusually low, it is difficult to reduce indoor pollutant concentrations more than approximately 50% by increasing the ventilation rate of an entire building. However, the efficiency of indoor pollutant control by ventilation can be enhanced through the use of local exhaust ventilation near concentrated sources of pollutants, by minimizing short circuiting of air from supply to exhaust when pollutant sources are dispersed and, in some situations, by promoting a displacement flow of air and pollutants toward the exhaust. Active air cleaning is also examined briefly. Filtration and electrostatic air cleaning for removal of particles from the indoor air are the most practical and effective currently available techniques of air cleaning. 49 refs., 7 figs.

  9. [Our experience with outside laboratory quality control].

    PubMed

    Dochev, D; Arakasheva, V; Nashkov, A; Tsachev, K

    1979-01-01

    The results from the national outside laboratory qualitative control of the clinical diagnostic laboratory investigations for the period September 1975 -- May 1977 were described. The following interlaboratory discrepancy was found on base of a systematic analysis of the data from the last two ring-like check-ups, November 1976 and May 1977, exressed by the variation coefficient (V.C. %); total protein, sodium, potassium and chlorides -- under 10%; cholesterol, urea and total fats -- between 10 and 20%; calcium, phosphorus, iron and creatinine -- over 20%. The highest per cent of admissible results are found with total protein -- to 85%; cholesterol -- to 70.38%; glucosa -- to 73.17%, urea -- to 69.23%, potassium -- to 59.46%, chlorides -- to 57.9%. With sodium, phosphorus, calcium, iron creatinine and uric acid the "admissibility" fluctuates about or under 50 per cent. The values of the qualitative-control indices discussed are comparable with the values obtained from them in the interlaboratory comparisons of other countries. PMID:494628

  10. 21 CFR 111.105 - What must quality control personnel do?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What must quality control personnel do? 111.105... for Quality Control § 111.105 What must quality control personnel do? Quality control personnel must... manufacturing record. To do so, quality control personnel must perform operations that include: (a) Approving...

  11. 40 CFR 81.112 - Charleston Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Regions § 81.112 Charleston Intrastate Air Quality Control Region. The Charleston Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... Quality Control Region: Region 1. 81.107Greenwood Intrastate Air Quality Control Region: Region 2....

  12. 40 CFR 81.112 - Charleston Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Regions § 81.112 Charleston Intrastate Air Quality Control Region. The Charleston Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... Quality Control Region: Region 1. 81.107Greenwood Intrastate Air Quality Control Region: Region 2....

  13. 21 CFR 111.105 - What must quality control personnel do?

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false What must quality control personnel do? 111.105... for Quality Control § 111.105 What must quality control personnel do? Quality control personnel must... manufacturing record. To do so, quality control personnel must perform operations that include: (a) Approving...

  14. Statistical Process Control: Going to the Limit for Quality.

    ERIC Educational Resources Information Center

    Training, 1987

    1987-01-01

    Defines the concept of statistical process control, a quality control method used especially in manufacturing. Generally, concept users set specific standard levels that must be met. Makes the point that although employees work directly with the method, management is responsible for its success within the plant. (CH)

  15. Silicon Sheet Quality is Improved By Meniscus Control

    NASA Technical Reports Server (NTRS)

    Yates, D. A.; Hatch, A. E.; Goldsmith, J. M.

    1983-01-01

    Better quality silicon crystals for solar cells are possible with instrument that monitors position of meniscus as sheet of solid silicon is drawn from melt. Using information on meniscus height, instrument generates feedback signal to control melt temperature. Automatic control ensures more uniform silicon sheets.

  16. CRN5EXP: Expert system for statistical quality control

    NASA Technical Reports Server (NTRS)

    Hentea, Mariana

    1991-01-01

    The purpose of the Expert System CRN5EXP is to assist in checking the quality of the coils at two very important mills: Hot Rolling and Cold Rolling in a steel plant. The system interprets the statistical quality control charts, diagnoses and predicts the quality of the steel. Measurements of process control variables are recorded in a database and sample statistics such as the mean and the range are computed and plotted on a control chart. The chart is analyzed through patterns using the C Language Integrated Production System (CLIPS) and a forward chaining technique to reach a conclusion about the causes of defects and to take management measures for the improvement of the quality control techniques. The Expert System combines the certainty factors associated with the process control variables to predict the quality of the steel. The paper presents the approach to extract data from the database, the reason to combine certainty factors, the architecture and the use of the Expert System. However, the interpretation of control charts patterns requires the human expert's knowledge and lends to Expert Systems rules.

  17. Quality control loop for 3D laser beam cutting

    NASA Astrophysics Data System (ADS)

    Spitznagel, Juergen

    1996-08-01

    Existing systems for computer integrated manufacturing are based on the principle of the process chain: The product runs through different production sections as design, work planning and manufacturing in a sequential order. The data generated by a production sequence are transferred via interface to the following production sequence. These tightly-packed production sequences leave little scope for responding to quality deviations. This deficit is highlighted particularly in 3D laser cutting processes. In order to achieve an optimum machining result, a series of preliminary tests is required. Quality control loops play an important role in restricting the scope of necessary testing to a minimum. The represented control loop contains a CAD- system to design the workpiece, an offline-programming system to develop working strategies and NC/RC-programs as well as a shop-floor oriented tool to record quality data of the workpiece. The systems are coupled by an integrated product model. The control loop feeds quality data back to Operations Planning in the form of rules for processing strategies and technological data, so that the quality of the production process is enhanced. It is intended to supply optimum process parameters, so that the number of preliminary tests can be reduced. On the other hand the control loop contributes quality enhancement measures which serve as rules for the designers.

  18. The impact of quality control in RNA-seq experiments

    NASA Astrophysics Data System (ADS)

    Merino, Gabriela A.; Fresno, Cristóbal; Netto, Frederico; Dias Netto, Emmanuel; Pratto, Laura; Fernández, Elmer A.

    2016-04-01

    High throughput mRNA sample sequencing, known as RNA-seq, is as a powerful approach to detect differentially expressed genes starting from millions of short sequence reads. Although several workflows have been proposed to analyze RNA-seq data, the experiment quality control as a whole is not usually considered, thus potentially biasing the results and/or causing information lost. Experiment quality control refers to the analysis of the experiment as a whole, prior to any analysis. It not only inspects the presence of technical effects, but also if general biological assumptions are fulfilled. In this sense, multivariate approaches are crucial for this task. Here, a multivariate approach for quality control in RNA-seq experiments is proposed. This approach uses simple and yet effective well-known statistical methodologies. In particular, Principal Component Analysis was successfully applied over real data to detect and remove outlier samples. In addition, traditional multivariate exploration tools were applied in order to asses several controls that can help to ensure the results quality. Based on differential expression and functional enrichment analysis, here is demonstrated that the information retrieval is significantly enhanced through experiment quality control. Results show that the proposed multivariate approach increases the information obtained from RNA-seq data after outlier samples removal.

  19. Oxidative stress and mitochondrial protein quality control in aging.

    PubMed

    Lionaki, Eirini; Tavernarakis, Nektarios

    2013-10-30

    Mitochondrial protein quality control incorporates an elaborate network of chaperones and proteases that survey the organelle for misfolded or unfolded proteins and toxic aggregates. Repair of misfolded or aggregated protein and proteolytic removal of irreversibly damaged proteins are carried out by the mitochondrial protein quality control system. Initial maturation and folding of the nuclear or mitochondrial-encoded mitochondrial proteins are mediated by processing peptidases and chaperones that interact with the protein translocation machinery. Mitochondrial proteins are subjected to cumulative oxidative damage. Thus, impairment of quality control processes may cause mitochondrial dysfunction. Aging has been associated with a marked decline in the effectiveness of mitochondrial protein quality control. Here, we present an overview of the chaperones and proteases involved in the initial folding and maturation of new, incoming precursor molecules, and the subsequent repair and removal of oxidized aggregated proteins. In addition, we highlight the link between mitochondrial protein quality control mechanisms and the aging process. This article is part of a Special Issue entitled: Posttranslational Protein modifications in biology and Medicine. PMID:23563202

  20. 75 FR 80066 - Quality Control Requirements for Direct Endorsement Lenders; Notice of Proposed Information...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-21

    ... URBAN DEVELOPMENT Quality Control Requirements for Direct Endorsement Lenders; Notice of Proposed.... This Notice also lists the following information: Title of Proposal: Quality Control Requirements for... lenders, since these institutions must also conduct quality control on all loans they originate...

  1. Space Shuttle flying qualities and flight control system assessment

    NASA Technical Reports Server (NTRS)

    Myers, T. T.; Mcruer, D. T.; Johnston, D. E.

    1982-01-01

    This paper reviews issues, data, and analyses relevant to the longitudinal flying qualities of the Space Shuttle in approach and landing. The manual control of attitude and path are first examined theoretically to demonstrate the unconventional nature of the Shuttle's augmented pitch and path response characteristics. The time domain pitch rate transient response criterion used for design of the Shuttle flight control system is examined in context with data from recent flying qualities experiments and operational aircraft. Questions arising from this examination are addressed through comparisons with MIL-F-8785C and other proposed flying qualities criteria which indicate potential longitudinal flying qualities problems. However, it is shown that these criteria, based largely on data from conventional aircraft, may be inappropriate for assessing the Shuttle.

  2. Conflict Inhibitory Control Facilitates Pretense Quality in Young Preschoolers

    PubMed Central

    Van Reet, Jennifer

    2013-01-01

    The present research explores the role of inhibitory control in young preschoolers’ pretense ability using an ego depletion paradigm. In Experiment 1 (N = 56), children’s pretense ability was assessed either before or after participating in conflict inhibitory control or control tasks, and in Experiment 2 (N = 36), pretense ability was measured after children engaged in either conflict or delay inhibitory control tasks. In both experiments, pretense scores were significantly higher only after engaging in conflict inhibitory control tasks. Further, pretense scores were positively correlated with inhibitory control scores when conflict inhibitory control was not experienced first. This pattern of results suggests that inhibitory control may underlie pretense, and conflict inhibitory control can boost the quality of children’s subsequent pretending. PMID:26074736

  3. Theoretical White Dwarf Spectra via the Internet: Quality Control

    NASA Astrophysics Data System (ADS)

    Ringat, E.; Reindl, N.

    2013-01-01

    The first decade of the Virtual Observatory (VO) built up services and tools for data conservation, handling, processing, analysis, etc. A new challenge in the immensely growing VO in operation is continuous quality control at different authority levels. Here we shed light on various aspects of theoretical white dwarf spectra that are provided via the registered TheoSSA VO service. We present benchmark tests that enable the VO user to judge their quality.

  4. Adequate supervision for children and adolescents.

    PubMed

    Anderst, James; Moffatt, Mary

    2014-11-01

    Primary care providers (PCPs) have the opportunity to improve child health and well-being by addressing supervision issues before an injury or exposure has occurred and/or after an injury or exposure has occurred. Appropriate anticipatory guidance on supervision at well-child visits can improve supervision of children, and may prevent future harm. Adequate supervision varies based on the child's development and maturity, and the risks in the child's environment. Consideration should be given to issues as wide ranging as swimming pools, falls, dating violence, and social media. By considering the likelihood of harm and the severity of the potential harm, caregivers may provide adequate supervision by minimizing risks to the child while still allowing the child to take "small" risks as needed for healthy development. Caregivers should initially focus on direct (visual, auditory, and proximity) supervision of the young child. Gradually, supervision needs to be adjusted as the child develops, emphasizing a safe environment and safe social interactions, with graduated independence. PCPs may foster adequate supervision by providing concrete guidance to caregivers. In addition to preventing injury, supervision includes fostering a safe, stable, and nurturing relationship with every child. PCPs should be familiar with age/developmentally based supervision risks, adequate supervision based on those risks, characteristics of neglectful supervision based on age/development, and ways to encourage appropriate supervision throughout childhood. PMID:25369578

  5. Small Rural Schools CAN Have Adequate Curriculums.

    ERIC Educational Resources Information Center

    Loustaunau, Martha

    The small rural school's foremost and largest problem is providing an adequate curriculum for students in a changing world. Often the small district cannot or is not willing to pay the per-pupil cost of curriculum specialists, specialized courses using expensive equipment no more than one period a day, and remodeled rooms to accommodate new…

  6. Funding the Formula Adequately in Oklahoma

    ERIC Educational Resources Information Center

    Hancock, Kenneth

    2015-01-01

    This report is a longevity, simulational study that looks at how the ratio of state support to local support effects the number of school districts that breaks the common school's funding formula which in turns effects the equity of distribution to the common schools. After nearly two decades of adequately supporting the funding formula, Oklahoma…

  7. 40 CFR 81.77 - Puerto Rico Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 18 2013-07-01 2013-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control...

  8. 40 CFR 81.77 - Puerto Rico Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 18 2012-07-01 2012-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control...

  9. 40 CFR 81.77 - Puerto Rico Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control...

  10. Can external quality control improve pig AI efficiency?

    PubMed

    Waberski, D; Petrunkina, A M; Töpfer-Petersen, E

    2008-11-01

    External quality control programmes carried out by central laboratories have been long established in human andrology with the aim of enhancing the accuracy and reproducibility of semen assessment. Compared to human, demands on boar semen assessment in AI stations are more complex, with the need both to identify boars with poor ejaculate quality and to monitor individual boar differences for semen storage. Additionally, appropriate assessment serves as a control instrument to ensure the security and efficiency of semen processing. Despite current limitations regarding the ability of sperm assays to estimate the potential fertility of males, it is evident that boar fertility is related to certain conventional semen tests, e.g. sperm morphology. In central studies carried out on stored semen from 11 AI stations, flow cytometric assessment of plasma and acrosome membrane integrity proved to be more sensitive in detecting sperm damage associated with ageing and temperature stress as compared to light microscopy. Membrane integrity of stored semen differed between AI stations indicating significant influences of semen processing on sperm quality. Thus external control of semen quality in reference laboratories may be useful to monitor the efficiency of internal semen quality control in individual AI stations, to identify males with lower semen quality and/or poor response to semen storage, and to verify the precision of sperm counting. The possibility that central laboratories with sufficient resources may be able to identify functionally different responding sperm subpopulations for better estimation of fertility is discussed. Ideally, external quality control schemes for AI stations would comprise application of validated tests with high relevance for fertility (including bacterial status), analysis of semen processing on the AI station, and training courses for laboratory personnel. PMID:18656253

  11. Demystifying ratings: How flow control shocks credit quality

    SciTech Connect

    Martin, J.H.

    1998-07-01

    Financial operations of many solid waste systems, waste-to-energy facilities in particular, have been shocked by the lack of congressional, and state and local legislation to resolve the loss of legal flow control. Flow control is a system's legal authority to direct waste into its own facilities. In contrast is economic flow control, where the market factors prevail and waste is brought to a facility based on competitive pricing. The loss of legal flow control threatens solid waste systems and impinges their underlying credit quality. Credit quality is expressed as the bond rating, a statement about the borrowers ability and willingness to repay debt in full and on time. While the courts have identified acceptable alternatives to enable municipal systems to diversity revenues (creating revenue flexibility), such alternatives may not be palatable as they represent additional taxation or fees. The paper highlights how the loss of legal flow control has shocked the operations, management and credit quality of solid waste systems. These shocks have stimulated public and private partnerships in order to facilitate economic flow control. Municipal credit solutions, credit impacts and credit trends are explained to identify how solid waste systems have responded in an operating climate exacerbated by regulatory changes (environmental and accounting) as well as utility deregulations. Analytical considerations are presented for evaluating the credit quality of solid waste bonds.

  12. Quality control for exposure assessment in epidemiological studies.

    PubMed

    Bornkessel, C; Blettner, M; Breckenkamp, J; Berg-Beckhoff, G

    2010-08-01

    In the framework of an epidemiological study, dosemeters were used for the assessment of radio frequency electromagnetic field exposure. To check the correct dosemeter's performance in terms of consistency of recorded field values over the entire study period, a quality control strategy was developed. In this paper, the concept of quality control and its results is described. From the 20 dosemeters used, 19 were very stable and reproducible, with deviations of a maximum of +/-1 dB compared with their initial state. One device was found to be faulty and its measurement data had to be excluded from the analysis. As a result of continuous quality control procedures, the confidence in the measurements obtained during the field work was strengthened significantly. PMID:20308051

  13. Methods of Statistical Control for Groundwater Quality Indicators

    NASA Astrophysics Data System (ADS)

    Yankovich, E.; Nevidimova, O.; Yankovich, K.

    2016-06-01

    The article describes the results of conducted groundwater quality control. Controlled quality indicators included the following microelements - barium, manganese, iron, mercury, iodine, chromium, strontium, etc. Quality control charts - X-bar chart and R chart - were built. For the upper and the lower threshold limits, maximum permissible concentration of components in water and the lower limit of their biologically significant concentration, respectively, were selected. The charts analysis has shown that the levels of microelements content in water at the area of study are stable. Most elements in the underground water are contained in concentrations, significant for human organisms consuming the water. For example, such elements as Ba, Mn, Fe have concentrations that exceed maximum permissible levels for drinking water.

  14. A multiple objective optimization approach to quality control

    NASA Technical Reports Server (NTRS)

    Seaman, Christopher Michael

    1991-01-01

    The use of product quality as the performance criteria for manufacturing system control is explored. The goal in manufacturing, for economic reasons, is to optimize product quality. The problem is that since quality is a rather nebulous product characteristic, there is seldom an analytic function that can be used as a measure. Therefore standard control approaches, such as optimal control, cannot readily be applied. A second problem with optimizing product quality is that it is typically measured along many dimensions: there are many apsects of quality which must be optimized simultaneously. Very often these different aspects are incommensurate and competing. The concept of optimality must now include accepting tradeoffs among the different quality characteristics. These problems are addressed using multiple objective optimization. It is shown that the quality control problem can be defined as a multiple objective optimization problem. A controller structure is defined using this as the basis. Then, an algorithm is presented which can be used by an operator to interactively find the best operating point. Essentially, the algorithm uses process data to provide the operator with two pieces of information: (1) if it is possible to simultaneously improve all quality criteria, then determine what changes to the process input or controller parameters should be made to do this; and (2) if it is not possible to improve all criteria, and the current operating point is not a desirable one, select a criteria in which a tradeoff should be made, and make input changes to improve all other criteria. The process is not operating at an optimal point in any sense if no tradeoff has to be made to move to a new operating point. This algorithm ensures that operating points are optimal in some sense and provides the operator with information about tradeoffs when seeking the best operating point. The multiobjective algorithm was implemented in two different injection molding scenarios

  15. Results of a quality control on non-interventional studies

    PubMed Central

    Wörz, Karl; Hundt, Ferdinand

    2011-01-01

    Non-interventional studies (NIS) have for decades been an established part of post-authorisation medicinal research. As early as the mid-nineties, there were at least rudimentary demands for controllable data quality. Beginning with the recommendations of the Federal Institute for Drugs and Medical Devices (BfArM) on the execution of non interventional (observational) studies of 1998 and finally with the guidelines and recommendations for ensuring Good Epidemiological Practice (GEP), with the VFA (Verband der forschenden Arzneimittelhersteller [German Association of Research-Based Pharmaceutical Companies]) – Recommendations for the Improvement of Quality and Transparency of NIS and the joint recommendations of BfArM and PEI (Paul-Ehrlich-Institut) on the execution of NIS, pharmaceutical companies are required to monitor and/or verify quality in the course of a project. According to a survey of pharmaceutical companies 2010, about one third of the companies surveyed to date carry out such quality controls on site, at participating study centres. This report deals with the results of such quality control measures in 4 completed projects. The control rates defined in the respective cohort study plans, the measures carried out on site and any consequent measures, such as adjustment of forms, reduction of consultation time and necessary organisational changes are described. A high level of agreement between the data collected and the original patient documents is found, comparable to that in clinical trials. PMID:21863135

  16. Results of a quality control on non-interventional studies.

    PubMed

    Wörz, Karl; Hundt, Ferdinand

    2011-01-01

    Non-interventional studies (NIS) have for decades been an established part of post-authorisation medicinal research. As early as the mid-nineties, there were at least rudimentary demands for controllable data quality. Beginning with the recommendations of the Federal Institute for Drugs and Medical Devices (BfArM) on the execution of non interventional (observational) studies of 1998 and finally with the guidelines and recommendations for ensuring Good Epidemiological Practice (GEP), with the VFA (Verband der forschenden Arzneimittelhersteller [German Association of Research-Based Pharmaceutical Companies]) - Recommendations for the Improvement of Quality and Transparency of NIS and the joint recommendations of BfArM and PEI (Paul-Ehrlich-Institut) on the execution of NIS, pharmaceutical companies are required to monitor and/or verify quality in the course of a project. According to a survey of pharmaceutical companies 2010, about one third of the companies surveyed to date carry out such quality controls on site, at participating study centres. This report deals with the results of such quality control measures in 4 completed projects. The control rates defined in the respective cohort study plans, the measures carried out on site and any consequent measures, such as adjustment of forms, reduction of consultation time and necessary organisational changes are described. A high level of agreement between the data collected and the original patient documents is found, comparable to that in clinical trials. PMID:21863135

  17. Possible approaches to fast quality control of IFE targets

    NASA Astrophysics Data System (ADS)

    Koresheva, E. R.; Nikitenko, A. I.; Aleksandrova, I. V.; Bazdenkov, S. V.; Belolipetskiy, A. A.; Chtcherbakov, V. I.; Osipov, I. E.

    2006-11-01

    In recent years, research into the development of reliable methods and techniques for characterization and quality control of ICF/IFE targets has been carried out very actively. This is motivated by the need to provide the means for precise and accurate knowledge of cryogenic target parameters. On the other hand, particular emphasis should be paid to the fact that fuelling of a commercial power plant requires ~6 targets each second. This indicates that the development of fast quality control techniques is of critical importance as well. Therefore, in this report we discuss the issues underlying the construction of different algorithms for characterization and quality control of ICF/IFE targets. Among them are: (a) algorithm banks and their structure, (b) algorithm testing, (c) target reconstruction experiments. The algorithm bank incorporates the algorithms for two stages of target production: the stage of fuel layering technique development (motionless target) and the stage of cryogenic target delivery (injected target). In the first case an inverse algorithm for individual target characterization (3D target reconstruction) and two threshold algorithms for fast control of target quality are presented. They are based on tomographic information processing methods. Experimentally, tomographic data acquisition is carried out by a hundred projections microtomograph. The spatial resolution of the optical system of the microtomograph is 1 µm for 490 nm wavelength, the accuracy of target angular positioning is ±1.5-2.5 min. In the second case we describe the algorithm based on Fourier transform holography for ultra fast target characterization during its injection. The performed computer experiments have demonstrated much promise of this approach in the following directions: recognition of the target imperfections in both low- and high- harmonics; quality control of both a single target and a target batch; simultaneous control of both an injected target quality and its

  18. Exercise Training Restores Cardiac Protein Quality Control in Heart Failure

    PubMed Central

    Campos, Juliane C.; Queliconi, Bruno B.; Dourado, Paulo M. M.; Cunha, Telma F.; Zambelli, Vanessa O.; Bechara, Luiz R. G.; Kowaltowski, Alicia J.; Brum, Patricia C.; Mochly-Rosen, Daria; Ferreira, Julio C. B.

    2012-01-01

    Exercise training is a well-known coadjuvant in heart failure treatment; however, the molecular mechanisms underlying its beneficial effects remain elusive. Despite the primary cause, heart failure is often preceded by two distinct phenomena: mitochondria dysfunction and cytosolic protein quality control disruption. The objective of the study was to determine the contribution of exercise training in regulating cardiac mitochondria metabolism and cytosolic protein quality control in a post-myocardial infarction-induced heart failure (MI-HF) animal model. Our data demonstrated that isolated cardiac mitochondria from MI-HF rats displayed decreased oxygen consumption, reduced maximum calcium uptake and elevated H2O2 release. These changes were accompanied by exacerbated cardiac oxidative stress and proteasomal insufficiency. Declined proteasomal activity contributes to cardiac protein quality control disruption in our MI-HF model. Using cultured neonatal cardiomyocytes, we showed that either antimycin A or H2O2 resulted in inactivation of proteasomal peptidase activity, accumulation of oxidized proteins and cell death, recapitulating our in vivo model. Of interest, eight weeks of exercise training improved cardiac function, peak oxygen uptake and exercise tolerance in MI-HF rats. Moreover, exercise training restored mitochondrial oxygen consumption, increased Ca2+-induced permeability transition and reduced H2O2 release in MI-HF rats. These changes were followed by reduced oxidative stress and better cardiac protein quality control. Taken together, our findings uncover the potential contribution of mitochondrial dysfunction and cytosolic protein quality control disruption to heart failure and highlight the positive effects of exercise training in re-establishing cardiac mitochondrial physiology and protein quality control, reinforcing the importance of this intervention as a non-pharmacological tool for heart failure therapy. PMID:23300764

  19. [Internal quality control for antimicrobial susceptibility test: an experience feedback].

    PubMed

    Vedy, Serge

    2012-01-01

    Internal quality control (IQC) position in antimicrobial susceptibility testing must be evaluated attentively before using. Ours S. aureus ATCC 25923 use during year 2011 has given precious information that can be useful for other laboratories. First, IQC should never be used before checking that all the realisation process steps are controlled. It will then appear that reagents are the most susceptible to give false results. That's what happens in 2.74% of antimicrobial susceptibility test. IQC is then useful to limit their clinical's impact. However, IQC use also shows that quality improvement will be difficult without industrial producer's involvement. PMID:22826843

  20. Annual Technol Conference Transactions - American Society for Quality Control, 34th: Quality in the New Decade, 1980

    SciTech Connect

    Not Available

    1980-05-01

    The conference transactions contain 129 papers dealing with such QC topics as: computer aided QC; metrology; human factors, risk, and product liability law; QC in food processing; statistical technique; quality costs principle; food, drug, and cosmetics; energy; automotive; metals; quality cost and startegic planning; quality motivation; textile and needle trades; environmental quality assurance; biomedical; service industry quality costs; application of quality circles; electronics; advanced reliability techniques; management; aerospace and defense planning and systems; small business quality control inspection; and reliability applications.

  1. [Study thought of pharmaceutical preparations quality standards by dynamic quality control technology].

    PubMed

    Yu, Dan-Hong; Mao, Chen-Mei; Lv, Cheng-Zhe; Jin, Hui-Zhen; Yao, Xin; Jia, Xiao-Bin

    2014-07-01

    Pharmaceutical preparations, particularly as a "secret recipe" of traditional Chinese medicine in medical institutions, are the product of China's medical and health industry, and they are also an important means of competing of different medical institutions. Although pharmaceutical preparations have advantages and characteristics than institutes for drug and pharmaceutical companies, the quality standards of pharmaceutical preparations in medical institutions has not reached the desired level over the years. As we all know, the quality of pharmaceutical preparations is important to ensure the efficacy, especially under the environment of people pay more sttention on drug safety and effectiveness and contry increase emphasis on the stste of pharmaceutical preparations. In view of this, we will improve the grade, stability, and clinical efficacy of pharmaceutical preparations by the advanced equipment, testing instruments and the process dynamic quality control technology. Finally, we hope we can provide new ideas for the quality control of pharmaceutical preparations. PMID:25272516

  2. Quality control and quality assurance procedures at the THOR BNCT facility.

    PubMed

    Liu, Yuan-Hao; Tsai, Pi-En; Lin, Yi-Chun; Huang, Chun-Kai; Liu, Hong-Ming; Jiang, Shiang-Huei

    2011-12-01

    Various quality control (QC) and quality assurance (QA) procedures of the boron neutron capture therapy (BNCT) beam at the Tsing Hua Open-pool Reactor (THOR) are established to ensure beam availability and quality. The QC/QA methods mainly employ foil activation and paired ionization chambers, respectively, for beam intensity check and dose assessment. Beam intensity is monitored on-line by using three dead-time corrected fission chambers. In addition to the periodic QC/QA activities regarding beam quality and the monitoring system, the quick QC/QA performed in an all-in-one phantom will be executed less than 70 min before the clinical treatment to guarantee beam quality. The QC/QA procedures have been gradually established and the actual performance satisfied the preset criteria defined for the BNCT facility at THOR. PMID:21605978

  3. Automated visual inspection stations for next-generation semiconductor package quality control

    NASA Astrophysics Data System (ADS)

    DeYong, Mark R.; Eskridge, Thomas C.; Grace, John W.; Newberry, Jeff E.; Jones, J. H.; Hart, B. E.

    1996-09-01

    In the last several years, the semiconductor industry has come to the realization that the package into which a die is placed is at least as critical to the performance of the complete electronic system as the die itself. This realization has led to an explosive effort across the entire industry to advance the state-of-the-art in semiconductor packaging. To date, this effort has already produced semiconductor packaging options on the scale of the die (i.e., chip scale packaging -- CSP). While CSPs and other advanced packaging techniques provide improved electronic system performance, they also increase the quality control burden (despite the highly automated processes used to manufacture the packages, quality control remains, for the most part, a manual operation). This paper addresses the necessary requirements of automated visual inspection (AVI) for quality control of current and future semiconductor packaging. The necessary requirements of the station are subdivided into two categories: those pertaining to the hardware platform, and those pertaining to the software reasoning engine. Hardware requirements are discussed in terms of finding the best match between commercial, off-the- shelf, hardware components and a given inspection application. Components reviewed include: imagers, optics, illumination systems, auto-focus/alignment systems, material handlers, parallel image preprocessors, and host computers. Applications reviewed include: pin grid array (PGA), ball grid array (BGA), and flip-chip package inspection. Also discussed in the hardware section are options that may be used when commercial components are not adequate. Software requirements are discussed in terms of the functionality required to provide accurate, real-time characterization of package quality, to gain operator acceptance, and to produce meaningful statistics for use in process control.

  4. [Physician-independent quality control of health services].

    PubMed

    Hess, Rainer

    2007-01-01

    Currently a physician-independent control of health services can only be managed by means of liability case law. Usually, claims are settled years after the service has been provided, based, though, on medical guidelines that have been established by the medical profession itself at the time of the provision of services. An essential factor in medical quality assurance (QA) is the involvement of the relevant physicians, which should be combined with external controls. Regarding quality in medicine, personal qualification will have to be distinguished from institutional quality and quality of healthcare, which should be ensured by internal and external QA. There is increasing pressure to publish QA results in an institution-related manner. However, the publication of results may lead to the unequal treatment of hospitals, as external QA includes only a limited number of indications (possible misjudgement of overall quality), and refers to different patient populations (no comparable treatment results). However, the publication of such outcome data will prevail in the long-term. The future vision of an external QA system comprises: 1. electronically based patient files and, derived thereof, pseudonymised data sets for QA; 2. IQWiG's participation in the definition of evidence-based indicators for quality assessment as well as the application of these indicators; 3. the full publication of results on an Internet platform. PMID:17711259

  5. Integrated evolutionary computation neural network quality controller for automated systems

    SciTech Connect

    Patro, S.; Kolarik, W.J.

    1999-06-01

    With increasing competition in the global market, more and more stringent quality standards and specifications are being demands at lower costs. Manufacturing applications of computing power are becoming more common. The application of neural networks to identification and control of dynamic processes has been discussed. The limitations of using neural networks for control purposes has been pointed out and a different technique, evolutionary computation, has been discussed. The results of identifying and controlling an unstable, dynamic process using evolutionary computation methods has been presented. A framework for an integrated system, using both neural networks and evolutionary computation, has been proposed to identify the process and then control the product quality, in a dynamic, multivariable system, in real-time.

  6. Process and quality verification controls for solid propellant manufacturing

    NASA Technical Reports Server (NTRS)

    Rogers, C. J.

    1983-01-01

    It is pointed out that in-process tests to verify quality and detect discrepant propellant which could compromise motor performance are essential elements of the solid composite propellant manufacturing process. The successful performance of the 260SL-1 and 260SL-2 motors aptly verified the controls used for manufacturing the propellant. The present investigation is concerned with the selected control parameters, and their relationships to composition and final propellant properties. Control performance is evaluated by comparison with processing data experienced in the manufacture of the propellant for the 260SL-1 motor. It is found that the in-process quality verification controls utilized in the propellant manufacturing process for the 260-in. diameter motor contributed significantly to the confidence of successful and predictable motor performance.

  7. The quality of randomized controlled trials in major anesthesiology journals.

    PubMed

    Greenfield, Mary Lou V H; Rosenberg, Andrew L; O'Reilly, Michael; Shanks, Amy M; Sliwinski, Michelle J; Nauss, Michael D

    2005-06-01

    Increased attention has been directed at the quality of randomized controlled trials (RCTs) and how they are being reported. We examined leading anesthesiology journals to identify if there were specific areas for improvement in the design and analysis of published clinical studies. All RCTs that appeared between January 2000 and December 2000 in leading anesthesiology journals (Anesthesiology,Anesthesia & Analgesia,Anaesthesia, and Canadian Journal of Anaesthesia) were retrieved by a MEDLINE search. We used a previously validated assessment tool, including 14 items associated with study quality, to determine a quality score for each article. The overall mean weighted quality score was 44% +/- 16%. Overall average scores were relatively high for appropriate controls (77% +/- 7%) and discussions of side effects (67% +/- 6%). Scores were very low for randomization blinding (5% +/- 2%), blinding observers to results (1% +/- 1%), and post-beta estimates (16% +/- 13%). Important pretreatment clinical predictors were absent in 32% of all studies. Significant improvement in the reporting and conduct of RCTs is required and should focus on randomization methodology, the blinding of investigators, and sample size estimates. Repeat assessments of the literature may improve the adoption of guidelines for the improvement of the quality of randomized controlled trials. PMID:15920210

  8. Flying qualities and control system characteristics for superaugmented aircraft

    NASA Technical Reports Server (NTRS)

    Myers, T. T.; Mcruer, D. T.; Johnston, D. E.

    1984-01-01

    Aircraft-alone dynamics and superaugmented control system fundamental regulatory properties including stability and regulatory responses of the basic closed-loop systems; fundamental high and low frequency margins and governing factors; and sensitivity to aircraft and controller parameters are addressed. Alternative FCS mechanizations, and mechanizational side effects are also discussed. An overview of flying qualities considerations encompasses general pilot operations as a controller in unattended, intermittent and trim, and full-attention regulatory or command control; effective vehicle primary and secondary response properties to pilot inputs and disturbances; pilot control architectural possibilities; and comparison of superaugmented and conventional aircraft path responses for different forms of pilot control. Results of a simple experimental investigation into pilot dynamic behavior in attitude control of superaugmented aircraft configurations with high frequency time laps and time delays are presented.

  9. Quality controls in integrative approaches to detect errors and inconsistencies in biological databases.

    PubMed

    Ghisalberti, Giorgio; Masseroli, Marco; Tettamanti, Luca

    2010-01-01

    Numerous biomolecular data are available, but they are scattered in many databases and only some of them are curated by experts. Most available data are computationally derived and include errors and inconsistencies. Effective use of available data in order to derive new knowledge hence requires data integration and quality improvement. Many approaches for data integration have been proposed. Data warehousing seams to be the most adequate when comprehensive analysis of integrated data is required. This makes it the most suitable also to implement comprehensive quality controls on integrated data. We previously developed GFINDer (http://www.bioinformatics.polimi.it/GFINDer/), a web system that supports scientists in effectively using available information. It allows comprehensive statistical analysis and mining of functional and phenotypic annotations of gene lists, such as those identified by high-throughput biomolecular experiments. GFINDer backend is composed of a multi-organism genomic and proteomic data warehouse (GPDW). Within the GPDW, several controlled terminologies and ontologies, which describe gene and gene product related biomolecular processes, functions and phenotypes, are imported and integrated, together with their associations with genes and proteins of several organisms. In order to ease maintaining updated the GPDW and to ensure the best possible quality of data integrated in subsequent updating of the data warehouse, we developed several automatic procedures. Within them, we implemented numerous data quality control techniques to test the integrated data for a variety of possible errors and inconsistencies. Among other features, the implemented controls check data structure and completeness, ontological data consistency, ID format and evolution, unexpected data quantification values, and consistency of data from single and multiple sources. We use the implemented controls to analyze the quality of data available from several different biological

  10. Quality control procedures for genome-wide association studies.

    PubMed

    Turner, Stephen; Armstrong, Loren L; Bradford, Yuki; Carlson, Christopher S; Crawford, Dana C; Crenshaw, Andrew T; de Andrade, Mariza; Doheny, Kimberly F; Haines, Jonathan L; Hayes, Geoffrey; Jarvik, Gail; Jiang, Lan; Kullo, Iftikhar J; Li, Rongling; Ling, Hua; Manolio, Teri A; Matsumoto, Martha; McCarty, Catherine A; McDavid, Andrew N; Mirel, Daniel B; Paschall, Justin E; Pugh, Elizabeth W; Rasmussen, Luke V; Wilke, Russell A; Zuvich, Rebecca L; Ritchie, Marylyn D

    2011-01-01

    Genome-wide association studies (GWAS) are being conducted at an unprecedented rate in population-based cohorts and have increased our understanding of the pathophysiology of complex disease. Regardless of context, the practical utility of this information will ultimately depend upon the quality of the original data. Quality control (QC) procedures for GWAS are computationally intensive, operationally challenging, and constantly evolving. Here we enumerate some of the challenges in QC of GWAS data and describe the approaches that the electronic MEdical Records and Genomics (eMERGE) network is using for quality assurance in GWAS data, thereby minimizing potential bias and error in GWAS results. We discuss common issues associated with QC of GWAS data, including data file formats, software packages for data manipulation and analysis, sex chromosome anomalies, sample identity, sample relatedness, population substructure, batch effects, and marker quality. We propose best practices and discuss areas of ongoing and future research. PMID:21234875

  11. Data quality control in social surveys using genetic information.

    PubMed

    Li, Yi; Guo, Guang

    2014-01-01

    This article introduces a novel way of taking advantage of genetic data in social surveys for the purposes of data quality control. Genetic information could detect and repair data issues such as missing data, reporting errors, differences in measures of the same variable, and flawed data. Using data from two surveys, the College Roommate Study (ROOM) and the National Longitudinal Study of Adolescent Health (Add Health), we show that proportion identical by descent score (a measure of genetic relationships) can identify "misreported" and unreported sibling type and detect misrepresented participants, bio-ancestry score (a measure of ancestral population memberships) can repair and recover missing race and discrepancies among different measures of self-reported race, and sex chromosomal information may help cross-check self-reported sex. This article represents an initial effort to utilize genetic data for the purposes of data quality control. As genetic data become increasingly available, researchers may explore more approaches to improving data quality. PMID:25343368

  12. An engineering approach to controlling indoor air quality.

    PubMed Central

    Woods, J E

    1991-01-01

    Evidence is accumulating that indicates air quality problems in residential and commercial buildings are nearly always associated with inadequacies in building design and methods of operation. Thus, the very systems depended on to control the indoor environment can become indirect sources of contamination if diligence is not exercised at each stage of a building's life: a) planning and design, b) construction and commissioning, c) operation, and d) demolition or renovation. In this paper, an engineering perspective is presented in which the existing building stock is characterized in terms of its environmental performance. Preliminary data indicate that 20 to 30% of the existing buildings have sufficient problems to manifest as sick-building syndrome or building-related illness, while another 10 to 20% may have undetected problems. Thus, only about 50 to 70% of the existing buildings qualify as healthy buildings. Two methods and three mechanisms of control are described to achieve "acceptable" indoor air quality: source control and exposure control. If sources cannot be removed, some level of occupant exposure will result. To control exposures with acceptable values, the primary sensory receptors of the occupants (i.e., thermal, ocular, auditory, and olfactory) cannot be excessively stimulated. The three exposure control mechanisms are conduction, radiation, and convection. To achieve acceptable occupant responses, it is often practical to integrate the mechanisms of radiation and convection in heating, ventilating, and air conditioning systems that are designed to provide acceptable thermal, acoustic, and air quality conditions within occupied spaces.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:1821369

  13. FIELD QUALITY CONTROL STRATEGIES ASSESSING SOLIDIFICATION/STABILIZATION

    EPA Science Inventory

    Existing regulatory mobility reduction (leaching) tests are not amenable to real time quality control because of the time required to perform sample extraction and chemical analysis. This is of conccern because the leaching test is the most important parameter used to relate trea...

  14. 18 CFR 12.40 - Quality control programs.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Quality control programs. 12.40 Section 12.40 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE FEDERAL POWER ACT SAFETY OF WATER POWER PROJECTS...

  15. 18 CFR 12.40 - Quality control programs.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Quality control programs. 12.40 Section 12.40 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE FEDERAL POWER ACT SAFETY OF WATER POWER PROJECTS...

  16. 18 CFR 12.40 - Quality control programs.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Quality control programs. 12.40 Section 12.40 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE FEDERAL POWER ACT SAFETY OF WATER POWER PROJECTS...

  17. 18 CFR 12.40 - Quality control programs.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Quality control programs. 12.40 Section 12.40 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE FEDERAL POWER ACT SAFETY OF WATER POWER PROJECTS...

  18. 18 CFR 12.40 - Quality control programs.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Quality control programs. 12.40 Section 12.40 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE FEDERAL POWER ACT SAFETY OF WATER POWER PROJECTS...

  19. 30 CFR 28.31 - Quality control plans; contents.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control plans; contents. 28.31 Section 28.31 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING SHORT-CIRCUIT PROTECTION FOR TRAILING CABLES IN COAL MINES...

  20. ACHIEVING IRRIGATION RETURN FLOW QUALITY CONTROL THROUGH IMPROVED LEGAL SYSTEMS

    EPA Science Inventory

    The key to irrigated agricultural return flow quality control is proper utilization and management of the resource itself, and an accepted tool in out society is the law. This project is designed to develop legal alternatives that will facilitate the implementation of improved wa...

  1. On the Need for Quality Control in Validation Research.

    ERIC Educational Resources Information Center

    Maier, Milton H.

    1988-01-01

    Validated aptitude tests used to help make personnel decisions about military recruits against hands-on tests of job performance in radio repairers and automotive mechanics. Data were filled with errors, reducing accuracy of validity coefficients. Discusses how validity coefficients can be made more accurate by exercising quality control during…

  2. Quality Control in Primary Schools: Progress from 2001-2006

    ERIC Educational Resources Information Center

    Hofman, Roelande H.; de Boom, Jan; Hofman, W. H. Adriaan

    2010-01-01

    This article presents findings of research into the quality control (QC) of schools from 2001-2006. In 2001 several targets for QC were set and the progress of 939 primary schools is presented. Furthermore, using cluster analysis, schools are classified into four QC-types that differ in their focus on school (self) evaluation and school…

  3. Quality Control Charts in Large-Scale Assessment Programs

    ERIC Educational Resources Information Center

    Schafer, William D.; Coverdale, Bradley J.; Luxenberg, Harlan; Jin, Ying

    2011-01-01

    There are relatively few examples of quantitative approaches to quality control in educational assessment and accountability contexts. Among the several techniques that are used in other fields, Shewart charts have been found in a few instances to be applicable in educational settings. This paper describes Shewart charts and gives examples of how…

  4. 30 CFR 28.30 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quality control plans; filing requirements. 28.30 Section 28.30 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING...

  5. 30 CFR 28.30 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quality control plans; filing requirements. 28.30 Section 28.30 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING...

  6. 30 CFR 28.30 - Quality control plans; filing requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quality control plans; filing requirements. 28.30 Section 28.30 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS FUSES FOR USE WITH DIRECT CURRENT IN PROVIDING...

  7. Protein quality control in organelles - AAA/FtsH story.

    PubMed

    Janska, Hanna; Kwasniak, Malgorzata; Szczepanowska, Joanna

    2013-02-01

    This review focuses on organellar AAA/FtsH proteases, whose proteolytic and chaperone-like activity is a crucial component of the protein quality control systems of mitochondrial and chloroplast membranes. We compare the AAA/FtsH proteases from yeast, mammals and plants. The nature of the complexes formed by AAA/FtsH proteases and the current view on their involvement in degradation of non-native organellar proteins or assembly of membrane complexes are discussed. Additional functions of AAA proteases not directly connected with protein quality control found in yeast and mammals but not yet in plants are also described shortly. Following an overview of the molecular functions of the AAA/FtsH proteases we discuss physiological consequences of their inactivation in yeast, mammals and plants. The molecular basis of phenotypes associated with inactivation of the AAA/FtsH proteases is not fully understood yet, with the notable exception of those observed in m-AAA protease-deficient yeast cells, which are caused by impaired maturation of mitochondrial ribosomal protein. Finally, examples of cytosolic events affecting protein quality control in mitochondria and chloroplasts are given. This article is part of a Special Issue entitled: Protein Import and Quality Control in Mitochondria and Plastids. PMID:22498346

  8. Sirt1-deficiency causes defective protein quality control

    PubMed Central

    Tomita, Takuya; Hamazaki, Jun; Hirayama, Shoshiro; McBurney, Michael W.; Yashiroda, Hideki; Murata, Shigeo

    2015-01-01

    Protein quality control is an important mechanism to maintain cellular homeostasis. Damaged proteins have to be restored or eliminated by degradation, which is mainly achieved by molecular chaperones and the ubiquitin-proteasome system. The NAD+-dependent deacetylase Sirt1 has been reported to play positive roles in the regulation of cellular homeostasis in response to various stresses. However, its contribution to protein quality control remains unexplored. Here we show that Sirt1 is involved in protein quality control in both an Hsp70-dependent and an Hsp70-independent manner. Loss of Sirt1 led to the accumulation of ubiquitinated proteins in cells and tissues, especially upon heat stress, without affecting proteasome activities. This was partly due to decreased basal expression of Hsp70. However, this accumulation was only partially alleviated by overexpression of Hsp70 or induction of Hsp70 upon heat shock in Sirt1-deficient cells and tissues. These results suggest that Sirt1 mediates both Hsp70-dependent and Hsp70-independent protein quality control. Our findings cast new light on understanding the role of Sirt1 in maintaining cellular homeostasis. PMID:26219988

  9. Quality control of leather by terahertz time-domain spectroscopy.

    PubMed

    Hernandez-Serrano, A I; Corzo-Garcia, S C; Garcia-Sanchez, E; Alfaro, M; Castro-Camus, E

    2014-11-20

    We use terahertz time-domain spectroscopy, combined with effective-medium theory, to measure the moisture content and thickness of leather simultaneously. These results demonstrate that this method could become a standard quality control test for the industrial tanning process. PMID:25607861

  10. 7 CFR 275.21 - Quality control review reports.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Responsibilities for... with Program requirements relative to the Quality Control Review System. Every case selected for review... information contained in the individual case records, or legible copies of that material, as well as...

  11. Summary of beam quality diagnostics and control working group

    SciTech Connect

    Lewellen, John; Piot, Philippe; /Northern Illinois U. /Fermilab

    2006-09-01

    The working group on beam quality, diagnostics, and control at the 12th Advanced Accelerator Concepts Workshop held a series of meetings during the Workshop. The generation of bright charged-particle beams (in particular electron and positron beams), along with state-of-the-art beam diagnostics and synchronization were discussed.

  12. Quality Control through Design and Process: Gambrel Roof Truss Challenge

    ERIC Educational Resources Information Center

    Ward, Dell; Jones, James

    2011-01-01

    Customers determine whether a product fulfills their needs or satisfies them. "Quality control", then, is the process of finding out what the customer wants, along with designing, producing, delivering, and servicing the product--and ultimately satisfying the customer's expectations. For many years, people considered a product to be of good…

  13. 21 CFR 864.8625 - Hematology quality control mixture.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Hematology Reagents § 864.8625...

  14. 21 CFR 864.8625 - Hematology quality control mixture.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Hematology Reagents § 864.8625...

  15. 21 CFR 864.8625 - Hematology quality control mixture.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Hematology Reagents § 864.8625...

  16. 21 CFR 864.8625 - Hematology quality control mixture.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Hematology Reagents § 864.8625...

  17. 21 CFR 864.8625 - Hematology quality control mixture.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Hematology quality control mixture. 864.8625 Section 864.8625 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Hematology Reagents § 864.8625...

  18. 7 CFR 275.21 - Quality control review reports.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 4 2011-01-01 2011-01-01 false Quality control review reports. 275.21 Section 275.21 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM PERFORMANCE REPORTING SYSTEM Responsibilities...

  19. DEVELOPMENT OF SUSPENDED SOLIDS QUALITY CONTROL AND PERFORMANCE EVALUATION SAMPLES

    EPA Science Inventory

    A two phase study was conducted to develop a synthetic suspended solids sample for use as quality control check and performance evaluation within environmental monitoring laboratories. The first phase consisted of a feasibility study to determine compounds that exhibited the opti...

  20. HANDBOOK FOR ANALYTICAL QUALITY CONTROL IN WATER AND WASTEWATER LABORATORIES

    EPA Science Inventory

    This handbook is addressed to laboratory directors, leaders of field investigations, and other personnel who bear responsibility for water and wastewater data. Subject matter of the handbook is concerned primarily with quality control (QC) for chemical and biological tests and me...

  1. QUALITY CONTROL FOR ENVIRONMENTAL MEASUREMENTS USING GAMMA-RAY SPECTROMETRY

    EPA Science Inventory

    This report describes the quality control procedures, calibration, collection, analysis, and interpretation of data in measuring the activity of gamma ray-emitting radionuclides in environmental samples. Included in the appendices are basic data for selected gamma ray-emitting ra...

  2. 21 CFR 211.22 - Responsibilities of quality control unit.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 4 2012-04-01 2012-04-01 false Responsibilities of quality control unit. 211.22 Section 211.22 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Organization...

  3. 21 CFR 211.22 - Responsibilities of quality control unit.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 4 2011-04-01 2011-04-01 false Responsibilities of quality control unit. 211.22 Section 211.22 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Organization...

  4. 21 CFR 211.22 - Responsibilities of quality control unit.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 4 2013-04-01 2013-04-01 false Responsibilities of quality control unit. 211.22 Section 211.22 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Organization...

  5. 21 CFR 211.22 - Responsibilities of quality control unit.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 4 2014-04-01 2014-04-01 false Responsibilities of quality control unit. 211.22 Section 211.22 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Organization...

  6. Stochastic Models of Quality Control on Test Misgrading.

    ERIC Educational Resources Information Center

    Wang, Jianjun

    Stochastic models are developed in this article to examine the rate of test misgrading in educational and psychological measurement. The estimation of inadvertent grading errors can serve as a basis for quality control in measurement. Limitations of traditional Poisson models have been reviewed to highlight the need to introduce new models using…

  7. GenePRIMP: A software quality control tool

    SciTech Connect

    Amrita Pati

    2010-05-05

    Amrita Pati of the DOE Joint Genome Institute's Genome Biology group describes the software tool GenePRIMP and how it fits into the quality control pipeline for microbial genomics. Further details regarding GenePRIMP appear in a paper published online May 2, 2010 in Nature Methods.

  8. GenePRIMP: A software quality control tool

    ScienceCinema

    Amrita Pati

    2010-09-01

    Amrita Pati of the DOE Joint Genome Institute's Genome Biology group describes the software tool GenePRIMP and how it fits into the quality control pipeline for microbial genomics. Further details regarding GenePRIMP appear in a paper published online May 2, 2010 in Nature Methods.

  9. Incorporating Quality Control Information in the Sensor Web

    NASA Astrophysics Data System (ADS)

    Devaraju, Anusuriya; Kunkel, Ralf; Bogena, Heye

    2013-04-01

    The rapid development of sensing technologies had led to the creation of large amounts of heterogeneous environmental observations. The Sensor Web provides a wider access to sensors and observations via common protocols and specifications. Observations typically go through several levels of quality control, and aggregation before they are made available to end-users. Raw data are usually inspected, and related quality flags are assigned. Data are gap-filled, and errors are removed. New data series may also be derived from one or more corrected data sets. Until now, it is unclear how these kinds of information can be captured in the Sensor Web Enablement (SWE) framework. Apart from the quality measures (e.g., accuracy, precision, tolerance, or confidence), the levels of observational series, the changes applied, and the methods involved must be specified. It is important that this kind of quality control information is well described and communicated to end-users to allow for a better usage and interpretation of data products. In this paper, we describe how quality control information can be incorporated into the SWE framework. Concerning this, first, we introduce the TERENO (TERrestrial ENvironmental Observatories), an initiative funded by the large research infrastructure program of the Helmholtz Association in Germany. The main goal of the initiative is to facilitate the study of long-term effects of climate and land use changes. The TERENO Online Data RepOsitORry (TEODOOR) is a software infrastructure that supports acquisition, provision, and management of observations within TERENO via SWE specifications and several other OGC web services. Next, we specify changes made to the existing observational data model to incorporate quality control information. Here, we describe the underlying TERENO data policy in terms of provision and maintenance issues. We present data levels, and their implementation within TEODOOR. The data levels are adapted from those used by

  10. Controlled Trials in Children: Quantity, Methodological Quality and Descriptive Characteristics of Pediatric Controlled Trials Published 1948-2006

    PubMed Central

    Thomson, Denise; Hartling, Lisa; Cohen, Eyal; Vandermeer, Ben; Tjosvold, Lisa; Klassen, Terry P.

    2010-01-01

    Background The objective of this study was to describe randomized controlled trials (RCTs) and controlled clinical trials (CCTs) in child health published between 1948 and 2006, in terms of quantity, methodological quality, and publication and trial characteristics. We used the Trials Register of the Cochrane Child Health Field for overall trends and a sample from this to explore trial characteristics in more detail. Methodology/Principal Findings We extracted descriptive data on a random sample of 578 trials. Ninety-six percent of the trials were published in English; the percentage of child-only trials was 90.5%. The most frequent diagnostic categories were infectious diseases (13.2%), behavioural and psychiatric disorders (11.6%), neonatal critical care (11.4%), respiratory disorders (8.9%), non-critical neonatology (7.9%), and anaesthesia (6.5%). There were significantly fewer child-only studies (i.e., more mixed child and adult studies) over time (P = 0.0460). The proportion of RCTs to CCTs increased significantly over time (P<0.0001), as did the proportion of multicentre trials (P = 0.002). Significant increases over time were found in methodological quality (Jadad score) (P<0.0001), the proportion of double-blind studies (P<0.0001), and studies with adequate allocation concealment (P<0.0001). Additionally, we found an improvement in reporting over time: adequate description of withdrawals and losses to follow-up (P<0.0001), sample size calculations (P<0.0001), and intention-to-treat analysis (P<0.0001). However, many trials still do not describe their level of blinding, and allocation concealment was inadequately reported in the majority of studies across the entire time period. The proportion of studies with industry funding decreased slightly over time (P = 0.003), and these studies were more likely to report positive conclusions (P = 0.028). Conclusions/Significance The quantity and quality of pediatric controlled trials has increased over

  11. Investigating friendship quality: an exploration of self-control and social control theories' friendship hypotheses.

    PubMed

    Boman, John H; Krohn, Marvin D; Gibson, Chris L; Stogner, John M

    2012-11-01

    While associations with deviant peers are well understood to impact individual development, less is understood about the relationship between friendship quality and delinquency. Two criminological theories--social control theory and self-control theory--are able to offer an explanation for the latter relationship. Social control and self-control theories both premise that delinquents will have largely fractured, weak, and "cold and brittle" friendships. This study investigates how variations in perceptions of friendship quality are related to the delinquency, maternal attachment, school attachment, and self-control levels of both a participant and his/her close friend. To explore these relationships, we use a diverse (14% black; 18% Hispanic; 9% Asian) sample of 2,154 emerging adults within 1,077 friendship pairs (66% female). In each dyad, both members perceived the friendship's quality and reported personal markers of delinquency, social bonds, and self-control. Several series of multilevel models are estimated that regress each participant's friendship quality perception onto the participant's and their friend's delinquency, attachments, self-control, and demographic characteristics. Results show that delinquents have as intense, or more intense, friendships as non-delinquents. However, low levels of both actor and partner attachments and self-control are independently related to low friendship quality, and this is especially true for self-control. Supplemental analyses demonstrate that the effect of self-control on friendship quality may be reduced when individuals in dyads are delinquent. In conclusion, studies that address friendship quality without including characteristics of multiple members of the friendship are only capturing part of one's estimate of friendship quality. PMID:22367018

  12. Investigating Friendship Quality: An Exploration of Self-Control and Social Control Theories' Friendship Hypotheses

    ERIC Educational Resources Information Center

    Boman, John H., IV; Krohn, Marvin D.; Gibson, Chris L.; Stogner, John M.

    2012-01-01

    While associations with deviant peers are well understood to impact individual development, less is understood about the relationship between friendship quality and delinquency. Two criminological theories--social control theory and self-control theory--are able to offer an explanation for the latter relationship. Social control and self-control…

  13. Manufacture and quality control of interconnecting wire hardnesses, Volume 1

    NASA Technical Reports Server (NTRS)

    1972-01-01

    A standard is presented for manufacture, installation, and quality control of eight types of interconnecting wire harnesses. The processes, process controls, and inspection and test requirements reflected are based on acknowledgment of harness design requirements, acknowledgment of harness installation requirements, identification of the various parts, materials, etc., utilized in harness manufacture, and formulation of a typical manufacturing flow diagram for identification of each manufacturing and quality control process, operation, inspection, and test. The document covers interconnecting wire harnesses defined in the design standard, including type 1, enclosed in fluorocarbon elastomer convolute, tubing; type 2, enclosed in TFE convolute tubing lines with fiberglass braid; type 3, enclosed in TFE convolute tubing; and type 5, combination of types 3 and 4. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated.

  14. Soil moisture and strength index for earthwork construction quality control

    NASA Astrophysics Data System (ADS)

    Sawangsuriya, A.; Wachiraporn, S.; Sramoon, W.

    2015-09-01

    This paper presents the implementation of soil moisture and strength index measurements for earthwork construction quality control as well as a link between the in situ testing and structural property of earthen materials. Use of the convenient Dynamic Cone Penetrometer (DCP) in conjunction with conventional moisture-density measurements enhances quality control by achieving acceptable level of compaction, more uniform structural properties, and aids developing a controlled design parameter during the earthwork construction. Soil strength in term of DCP index normalized by the deviation of compaction moisture content from the optimum moisture content is proposed as performance criteria for a variety of engineered earth fills and special engineering assessment, prevention, and mitigation of geohazards e.g. earthen flood defense embankments.

  15. [Quality control of recombinant oncolytic adenovirus/p53].

    PubMed

    Gao, Kai; Bi, Hua; Ding, You-Xue; Li, Yong-Hong; Han, Chun-Mei; Guo, Ying; Rao, Chun-Ming

    2011-12-01

    To establish a detection method of oncolytic adenovirus/p53 and standard of quality control, human telomerase reverse transcriptase (hTERT) promoter, CMV fusion promoter containing hypoxia reaction element (HRE) and p53 gene were identified by vector DNA restriction enzyme digestion and PCR analysis. The result conformed that all modified regions were in consistent with theoretical ones. Particle number was 2.0 x 10(11) mL(-1) determined by UV (A260). Infectious titer was 5.0 x 10(10) IU mL(-1) analyzed by TCID50. In vitro p53 gene expression in human lung cancer cell H1299 was determined by ELISA, and A450 ratio of nucleoprotein in virus infection group to control group was 5.2. Antitumor potency was evaluated by cytotoxicity assay using human lung cancer cell A549, and the MOI(IC50) of this gene therapy preparation was 1.0. The tumor cells targeted replication ability of recombinant virus was determined by TCID50 titer ratio of filial generation virus between human lung cancer cell A549 and human diploid epidermal fibrolast BJ cells after infected by virus with same MOI. TCID50 titer ratio of tumor cell infection group to normal cell infection control group was 398. The IE-HPLC purity of virus was 99.5%. There was less than 1 copy of wild type adenovirus within 1 x 10(7) VP recombinant virus. Other quality control items were complied with corresponding requirements in the guidance for human somatic cell therapy and gene therapy and Chinese pharmacopeia volume III. The detection method of oncolytic adenovirus/p53 was successfully established for quality control standard. The study also provided reference for quality control of other oncolytic viral vector products. PMID:22375422

  16. 21 CFR 111.105 - What must quality control personnel do?

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 2 2012-04-01 2012-04-01 false What must quality control personnel do? 111.105 Section 111.105 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... for Quality Control § 111.105 What must quality control personnel do? Quality control personnel...

  17. 40 CFR 81.97 - Southwest Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.97 Section 81.97 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.97 Southwest Florida Intrastate Air Quality Control Region. The Southwest Florida Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  18. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.30 Section 81.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the...

  19. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.44 Section 81.44 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of...

  20. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.41 Section 81.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of...

  1. 40 CFR 81.120 - Middle Tennessee Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.120 Section 81.120 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.120 Middle Tennessee Intrastate Air Quality Control Region. The Middle Tennessee Intrastate Air Quality Control Region consists of the territorial area encompassed...

  2. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.24 Section 81.24 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial...

  3. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.16 Section 81.16 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial...

  4. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.23 Section 81.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the...

  5. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.20 Section 81.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist...

  6. 40 CFR 81.89 - Metropolitan Cheyenne Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.89 Section 81.89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.89 Metropolitan Cheyenne Intrastate Air Quality Control Region. The Metropolitan Cheyenne Intrastate Air Quality Control Region (Wyoming) consists of the territorial...

  7. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.48 Section 81.48 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of...

  8. 40 CFR 81.29 - Metropolitan Indianapolis Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Air Quality Control Region. 81.29 Section 81.29 Protection of Environment ENVIRONMENTAL PROTECTION... Designation of Air Quality Control Regions § 81.29 Metropolitan Indianapolis Intrastate Air Quality Control Region. The Metropolitan Indianapolis Intrastate Air Quality Control Region consists of the...

  9. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.62 Section 81.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the...

  10. 40 CFR 81.29 - Metropolitan Indianapolis Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Air Quality Control Region. 81.29 Section 81.29 Protection of Environment ENVIRONMENTAL PROTECTION... Designation of Air Quality Control Regions § 81.29 Metropolitan Indianapolis Intrastate Air Quality Control Region. The Metropolitan Indianapolis Intrastate Air Quality Control Region consists of the...

  11. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.43 Section 81.43 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial...

  12. 40 CFR 81.98 - Burlington-Keokuk Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.98 Section 81.98 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.98 Burlington-Keokuk Interstate Air Quality Control Region. The Burlington-Keokuk Interstate Air Quality Control Region (Illinois-Iowa) is revised to consist of...

  13. 40 CFR 81.116 - Northern Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.116 Section 81.116 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.116 Northern Missouri Intrastate Air Quality Control Region. The Northern Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  14. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.75 Section 81.75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been...

  15. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.43 Section 81.43 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial...

  16. 40 CFR 81.36 - Maricopa Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Regions § 81.36 Maricopa Intrastate Air Quality Control Region. The Phoenix-Tucson Intrastate Air Quality Control Region has been renamed the Maricopa Intrastate Air Quality Control Region... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Maricopa Intrastate Air...

  17. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.34 Section 81.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  18. 40 CFR 81.87 - Metropolitan Boise Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.87 Section 81.87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.87 Metropolitan Boise Intrastate Air Quality Control Region. The Metropolitan Boise Intrastate Air Quality Control Region (Idaho) consists of the territorial area...

  19. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.16 Section 81.16 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial...

  20. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.75 Section 81.75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been...

  1. 40 CFR 81.36 - Maricopa Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Regions § 81.36 Maricopa Intrastate Air Quality Control Region. The Phoenix-Tucson Intrastate Air Quality Control Region has been renamed the Maricopa Intrastate Air Quality Control Region... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Maricopa Intrastate Air...

  2. 40 CFR 81.89 - Metropolitan Cheyenne Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.89 Section 81.89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.89 Metropolitan Cheyenne Intrastate Air Quality Control Region. The Metropolitan Cheyenne Intrastate Air Quality Control Region (Wyoming) consists of the territorial...

  3. 40 CFR 81.104 - Central Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.104 Section 81.104 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.104 Central Pennsylvania Intrastate Air Quality Control Region. The Central Pennsylvania Intrastate Air Quality Control Region consists of the territorial area encompassed...

  4. 20 CFR 602.41 - Proper expenditure of Quality Control granted funds.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Proper expenditure of Quality Control granted... LABOR QUALITY CONTROL IN THE FEDERAL-STATE UNEMPLOYMENT INSURANCE SYSTEM Quality Control Grants to States § 602.41 Proper expenditure of Quality Control granted funds. The Secretary may, after...

  5. 40 CFR 81.98 - Burlington-Keokuk Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.98 Section 81.98 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.98 Burlington-Keokuk Interstate Air Quality Control Region. The Burlington-Keokuk Interstate Air Quality Control Region (Illinois-Iowa) is revised to consist of...

  6. 40 CFR 81.101 - Metropolitan Dubuque Interstate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.101 Section 81.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.101 Metropolitan Dubuque Interstate Air Quality Control Region. The Metropolitan Dubuque Interstate Air Quality Control Region (Illinois-Iowa-Wisconsin) consists of...

  7. 40 CFR 81.106 - Greenville-Spartanburg Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.106 Section 81.106 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.106 Greenville-Spartanburg Intrastate Air Quality Control Region. The Greenville-Spartanburg Intrastate Air Quality Control Region (South Carolina) consists of the...

  8. 40 CFR 81.117 - Southeast Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.117 Section 81.117 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.117 Southeast Missouri Intrastate Air Quality Control Region. The Southeast Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  9. 40 CFR 81.118 - Southwest Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.118 Section 81.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.118 Southwest Missouri Intrastate Air Quality Control Region. The Southwest Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  10. 30 CFR 28.32 - Proposed quality control plans; approval by MSHA.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Proposed quality control plans; approval by...-CIRCUIT PROTECTION FOR TRAILING CABLES IN COAL MINES Quality Control § 28.32 Proposed quality control plans; approval by MSHA. (a) Each proposed quality control plan submitted in accordance with...

  11. 40 CFR 81.51 - Portland Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Regions § 81.51 Portland Interstate Air Quality Control Region. The Portland Interstate Air Quality Control Region (Oregon-Washington) has been revised to consist of the territorial area... Portland Interstate Air Quality Control Region (Oregon-Washington) will be referred to by...

  12. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.41 Section 81.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of...

  13. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.23 Section 81.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the...

  14. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.34 Section 81.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  15. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.30 Section 81.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the...

  16. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.62 Section 81.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the...

  17. 40 CFR 81.87 - Metropolitan Boise Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.87 Section 81.87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.87 Metropolitan Boise Intrastate Air Quality Control Region. The Metropolitan Boise Intrastate Air Quality Control Region (Idaho) consists of the territorial area...

  18. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.49 Section 81.49 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  19. 40 CFR 81.116 - Northern Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.116 Section 81.116 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.116 Northern Missouri Intrastate Air Quality Control Region. The Northern Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  20. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.24 Section 81.24 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial...

  1. 40 CFR 81.117 - Southeast Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.117 Section 81.117 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.117 Southeast Missouri Intrastate Air Quality Control Region. The Southeast Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  2. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.20 Section 81.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist...

  3. 40 CFR 81.104 - Central Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.104 Section 81.104 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.104 Central Pennsylvania Intrastate Air Quality Control Region. The Central Pennsylvania Intrastate Air Quality Control Region consists of the territorial area encompassed...

  4. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.49 Section 81.49 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  5. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.44 Section 81.44 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of...

  6. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.45 Section 81.45 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of...

  7. 40 CFR 81.97 - Southwest Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.97 Section 81.97 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.97 Southwest Florida Intrastate Air Quality Control Region. The Southwest Florida Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  8. 20 CFR 602.41 - Proper expenditure of Quality Control granted funds.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Proper expenditure of Quality Control granted... LABOR QUALITY CONTROL IN THE FEDERAL-STATE UNEMPLOYMENT INSURANCE SYSTEM Quality Control Grants to States § 602.41 Proper expenditure of Quality Control granted funds. The Secretary may, after...

  9. 40 CFR 81.106 - Greenville-Spartanburg Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.106 Section 81.106 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.106 Greenville-Spartanburg Intrastate Air Quality Control Region. The Greenville-Spartanburg Intrastate Air Quality Control Region (South Carolina) consists of the...

  10. 40 CFR 81.118 - Southwest Missouri Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Quality Control Region. 81.118 Section 81.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.118 Southwest Missouri Intrastate Air Quality Control Region. The Southwest Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  11. 40 CFR 81.101 - Metropolitan Dubuque Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.101 Section 81.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.101 Metropolitan Dubuque Interstate Air Quality Control Region. The Metropolitan Dubuque Interstate Air Quality Control Region (Illinois-Iowa-Wisconsin) consists of...

  12. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.45 Section 81.45 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of...

  13. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Quality Control Region. 81.48 Section 81.48 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of...

  14. Quality Control and Quality Assurance in Teacher Training Institutions: Messages from Botswana.

    ERIC Educational Resources Information Center

    Hopkin, A. G.

    1999-01-01

    External factors, such as university affiliation, can help improve teacher-training programs. Using the University of Botswana (UB) as an example, this paper discusses quality control and assurance; evaluates their impact on courses offered, final examinations, and teaching practice; and evaluates operational drawbacks of UB's system, suggesting…

  15. Structural Quality Control of Swiss-Type Cheese with Ultrasound

    NASA Astrophysics Data System (ADS)

    Eskelinen, J.; Alavuotunki, A.; Hæggström, E.; Alatossava, T.

    2007-03-01

    A study on structural quality control of Swiss-type cheese with ultrasound is presented. We used a longitudinal mode pulse-echo setup using 1-2MHz ultrasonic frequencies to detect cheese-eyes and ripening induced cracks. Results show that the ultrasonic method posses good potential to monitor the cheese structure during the ripening process. Preliminary results indicate that maturation stage could be monitored with ultrasonic velocity measurements. Further studies to verify the method's on-line potential to detect low-structural-quality cheeses are planned.

  16. Operational Quality Control of SAR Data under the IDEAS Contract

    NASA Astrophysics Data System (ADS)

    Griffiths, Emma; Haria, Kajal; Meadowws, Peter; Miranda, Nuno

    2010-12-01

    Operational Quality Control (QC) of ERS-1/2 Synthetic Aperture Radar (SAR), Envisat's Advanced Synthetic Aperture Radar (ASAR) and the Phased-Array L-band SAR (PALSAR) on board JAXA's Advanced Land Observing Satellite (ALOS) is currently carried out under the Image Data quality Evaluation and Analysis Service (IDEAS). This paper introduces the concept of IDEAS as it applies to SAR QC including the daily and long-term analysis and shows the interaces to related services, including ESA's user-facing Earth Observation (EO) Help Desk

  17. Multi-rule quality control for the age-related eye disease study.

    PubMed

    Caudill, Samuel P; Schleicher, Rosemary L; Pirkle, James L

    2008-09-10

    The Age-Related Eye Disease Study (AREDS), sponsored by the National Eye Institute, was designed to study the natural history and risk factors of age-related macular degeneration (AMD) and cataract, and to evaluate the effect of high doses of antioxidants and zinc on eye disease progression. AMD and cataract are leading causes of visual impairment and blindness in the U.S., with frequency of both diseases increasing dramatically after age 65. Participants were randomly chosen to receive antioxidant or placebo tablets. Blood was drawn annually from a subset of patients, and serum concentrations of 17 different nutritional indicators were measured. Because of the complexity of the analytical methods, and possibility of instrument error due to failure of any one of many component parts, several different instruments were used for most analytes. In addition, to assure that the measurement systems were performing adequately across a wide range of concentrations, multiple control pools were monitored with analyte concentrations at low, medium, and high concentrations. We report here the multi-rule quality control system (MRQCS) used during the later part of the trial (AREDS Phase III). This system was designed to monitor systematic error and random within- and among-run error for analytical runs using 1-3 different quality control pools per run and 1-2 measurements of each pool per run. We demonstrate the features of the MRQCS using quality control (QC) data associated with vitamin C measurements. We also provide operating characteristics to demonstrate how the MRQCS responds to increases in systematic and/or random error. PMID:18344178

  18. V/STOL Dynamics, Control, and Flying Qualities

    NASA Technical Reports Server (NTRS)

    Franklin, James A.

    2000-01-01

    This publication presents material that constituted the lectures presented by the author as part of Course AA 234, Dynamics, Control, and Flying Qualities of Vertical/Short Takeoff and Landing (V/STOL) Aircraft that was taught in the Department of Aeronautics and Astronautics at Stanford University. It covers representative operations of vertical and short takeoff and landing (V/STOL) aircraft, a discussion of the pilot's strategy in controlling these aircraft, the equations of motion pertinent to V/STOL tasks, and their application in the analysis of longitudinal and lateral-directional control in hover and forward flight. Following that development, which applies to the characteristics of the basic airframe and propulsion system, the text concludes with a discussion of the contributions of control augmentation in specific flight tasks and of the integration of modern electronic displays with these controls.

  19. Control Quality of a Feedback Control System under Cyclostationary Noise in Power Line Communication

    NASA Astrophysics Data System (ADS)

    Carrizo, Cesar; Kobayashi, Kentaro; Okada, Hiraku; Katayama, Masaaki

    This paper discusses a control system that employs a power line to transfer signals to control the motion of a single machine, and explores the influence of packet losses on the quality of the control. As an example of a controlled system, a controller with a rotary inverted pendulum as a controlled object, is considered. The feedback loop in between is the power line. The control performance is evaluated in the power line cyclostationary noise environment and compared against the performance in a stationary noise environment. As a result, it is confirmed that the power line and its cyclostationary noise features present an advantage against transmission in a channel with stationary noise.

  20. Quality control of the RMI's AWS wind observations

    NASA Astrophysics Data System (ADS)

    Bertrand, Cédric; González Sotelino, Luis; Journée, Michel

    2016-02-01

    Wind observations are important for a wide range of domains including among others meteorology, agriculture and extreme wind engineering. To ensure the provision of high quality surface wind data over Belgium, a new semi-automated data quality control (QC) has been developed and applied to wind observations from the automated weather stations operated by the Royal Meteorological Institute of Belgium. This new QC applies to 10 m 10 min averaged wind speed and direction, 10 m gust speed and direction, 2 m 10 min averaged wind speed and 30 m 10 min averaged wind speed records. After an existence test, automated procedures check the data for limits consistency, internal consistency, temporal consistency and spatial consistency. At the end of the automated QC, a decision algorithm attributes a flag to each particular data point. Each day, the QC staff analyzes the preceding day's observations in the light of the assigned quality flags.

  1. Image quality evaluation and control of computer-generated holograms

    NASA Astrophysics Data System (ADS)

    Yoshikawa, Hiroshi; Yamaguchi, Takeshi; Uetake, Hiroki

    2016-03-01

    Image quality of the computer-generated holograms are usually evaluated subjectively. For example, the re- constructed image from the hologram is compared with other holograms, or evaluated by the double-stimulus impairment scale method to compare with the original image. This paper proposes an objective image quality evaluation of a computer-generated hologram by evaluating both diffraction efficiency and peak signal-to-noise ratio. Theory and numerical experimental results are shown on Fourier transform transmission hologram of both amplitude and phase modulation. Results without the optimized random phase show that the amplitude transmission hologram gives better peak signal-to noise ratio, but the phase transmission hologram provides about 10 times higher diffraction efficiency to the amplitude type. As an optimized phase hologram, Kinoform is evaluated. In addition, we investigate to control image quality by non-linear operation.

  2. Active sound quality control of engine induced cavity noise

    NASA Astrophysics Data System (ADS)

    de Oliveira, Leopoldo P. R.; Janssens, Karl; Gajdatsy, Peter; Van der Auweraer, Herman; Varoto, Paulo S.; Sas, Paul; Desmet, Wim

    2009-02-01

    Active control solutions appear to be a feasible approach to cope with the steadily increasing requirements for noise reduction in the transportation industry. Active controllers tend to be designed with a target on the sound pressure level reduction. However, the perceived control efficiency for the occupants can be more accurately assessed if psychoacoustic metrics can be taken into account. Therefore, this paper aims to evaluate, numerically and experimentally, the effect of a feedback controller on the sound quality of a vehicle mockup excited with engine noise. The proposed simulation scheme is described and experimentally validated. The engine excitation is provided by a sound quality equivalent engine simulator, running on a real-time platform that delivers harmonic excitation in function of the driving condition. The controller performance is evaluated in terms of specific loudness and roughness. It is shown that the use of a quite simple control strategy, such as a velocity feedback, can result in satisfactory loudness reduction with slightly spread roughness, improving the overall perception of the engine sound.

  3. What records managers should know about quality control.

    PubMed

    Bauer, C J

    1983-09-01

    This article has been written to assist the records manager who may be faced with the task of determining qualitative standards for microfilm services. While the discussion will cover a wide spectrum of microform products, it is aimed primarily at those who are considering the conversion of source documents to conventional roll film or jackets. It includes an explanation of the impact of poor quality on the use of film in a records management program, and offers suggestions for the establishment of minimum standards for both inhouse and service bureau filming. A sample contract is provided to aid in developing a more specific contract. The article is based on experience gained in the operation of a microfilm service bureau, and is a result of having observed the consequences of microfilm conversion efforts which were entered into without adequate preparation and without a definition of specific standards. Recommended standards are based upon AIIM criteria for source document microfilm and articulated in such a manner as to permit inclusion in a contract proposal or inhouse working policy. PMID:10263973

  4. Annual technical conference transactions. American Society for Quality Control, 34th: quality in the new decade, 1980

    SciTech Connect

    Not Available

    1981-01-01

    The conference transactions contain 129 papers dealing with such QC topics as: computer aided QC; metrology; human factors, risk, and product liability law; QC in food processing; statistical techniques; quality costs principle; food, drug, and cosmetics; energy; automotive; metals; quality cost and strategic planning; quality motivation; textile and needle trades; environmental quality assurance; biomedical; service industry quality costs; application of quality circles; electronics; advanced reliability techniques; inspection application; chemical quality management; aerospace and defense planning and systems; small business quality control inspection; and reliability applications.

  5. Verification and quality control of routine hematology analyzers.

    PubMed

    Vis, J Y; Huisman, A

    2016-05-01

    Verification of hematology analyzers (automated blood cell counters) is mandatory before new hematology analyzers may be used in routine clinical care. The verification process consists of several items which comprise among others: precision, accuracy, comparability, carryover, background and linearity throughout the expected range of results. Yet, which standard should be met or which verification limit be used is at the discretion of the laboratory specialist. This paper offers practical guidance on verification and quality control of automated hematology analyzers and provides an expert opinion on the performance standard that should be met by the contemporary generation of hematology analyzers. Therefore (i) the state-of-the-art performance of hematology analyzers for complete blood count parameters is summarized, (ii) considerations, challenges, and pitfalls concerning the development of a verification plan are discussed, (iii) guidance is given regarding the establishment of reference intervals, and (iv) different methods on quality control of hematology analyzers are reviewed. PMID:27161194

  6. Quality control of cytoskeletal proteins and human disease.

    PubMed

    Lundin, Victor F; Leroux, Michel R; Stirling, Peter C

    2010-05-01

    Actins and tubulins are abundant cytoskeletal proteins that support diverse cellular processes. Owing to the unique properties of these filament-forming proteins, an intricate cellular machinery consisting minimally of the chaperonin CCT, prefoldin, phosducin-like proteins, and tubulin cofactors has evolved to facilitate their biogenesis. More recent evidence also suggests that regulated degradation pathways exist for actin (via TRIM32) and tubulin (via parkin or cofactor E-like). Collectively, these pathways maintain the quality control of cytoskeletal proteins ('proteostasis'), ensuring the appropriate function of microfilaments and microtubules. Here, we focus on the molecular mechanisms of the quality control of actin and tubulin, and discuss emerging links between cytoskeletal proteostasis and human diseases. PMID:20116259

  7. X-ray Spectroscopy for Quality Control of Chemotherapy Drugs

    SciTech Connect

    Greaves, E. D.; Barros, H.; Bermudez, J.; Sajo-Bohus, L.; Angeli-Greaves, M.

    2007-10-26

    We develop a method, employing Compton peak standardization and the use of matrix-matched spiked samples with Total Reflection X-ray Fluorescence (TXRF), for the determination of platinum plasma concentrations of patients undergoing chemotherapy with Pt-bearing drugs. Direct blood plasma analysis attains Pt detection limits of 70 ng/ml. Measurement results of prescribed drug doses are compared to achieved blood Pt concentrations indicating a lack of expected correlations. Direct analysis of Pt-containing infused drugs from a variety of suppliers indicates cases of abnormal concentrations which raises quality control issues. We demonstrate the potential usefulness of the method for pharmacokinetic studies or for routine optimization and quality control of Pt chemotherapy treatments.

  8. Viral Evasion and Manipulation of Host RNA Quality Control Pathways.

    PubMed

    Hogg, J Robert

    2016-08-15

    Viruses have evolved diverse strategies to maximize the functional and coding capacities of their genetic material. Individual viral RNAs are often used as substrates for both replication and translation and can contain multiple, sometimes overlapping open reading frames. Further, viral RNAs engage in a wide variety of interactions with both host and viral proteins to modify the activities of important cellular factors and direct their own trafficking, packaging, localization, stability, and translation. However, adaptations increasing the information density of small viral genomes can have unintended consequences. In particular, viral RNAs have developed features that mark them as potential targets of host RNA quality control pathways. This minireview focuses on ways in which viral RNAs run afoul of the cellular mRNA quality control and decay machinery, as well as on strategies developed by viruses to circumvent or exploit cellular mRNA surveillance. PMID:27226372

  9. Automated quality control for genome wide association studies

    PubMed Central

    Ellingson, Sally R.; Fardo, David W.

    2016-01-01

    This paper provides details on the necessary steps to assess and control data in genome wide association studies (GWAS) using genotype information on a large number of genetic markers for large number of individuals. Due to varied study designs and genotyping platforms between multiple sites/projects as well as potential genotyping errors, it is important to ensure high quality data. Scripts and directions are provided to facilitate others in this process.

  10. Real-time quality control: the French Minitel system.

    PubMed

    Goguel, A; LeBlanc, A

    1990-01-01

    A prototype system designed to provide real-time response to inter-laboratory proficiency testing results has been developed using the French Minitel telecommunication system. This nationwide computer networking system allows for instantaneous reporting and evaluation of results obtained on external quality assessment (EQA) samples. If a certain test is in error and presumably out of control the problem can be remedied immediately with obvious advantages to patient care. PMID:2282753

  11. Thermal analyses for quality control of plastics, ceramics, and explosives

    SciTech Connect

    Brown, C.R.; Garrod, M.J.; Whitaker, R.B.

    1990-01-01

    Thermal analyses are performed for production quality control (q.c.) and for surveillance at Mound on plastic, ceramic, explosive and pyrotechnic materials. For the weapons surveillance program, weapon components are disassembled after varying times in the field; thermal and other analyses are then performed on the component materials. The types of thermal analyses done include: differential scanning calorimetry (DSC), differential thermal analysis (DTA), thermogravimetry (TG), thermomechanical analysis (TMA), and high temperature TG/DTA. 5 refs., 4 figs.

  12. Automated quality control in a file-based broadcasting workflow

    NASA Astrophysics Data System (ADS)

    Zhang, Lina

    2014-04-01

    Benefit from the development of information and internet technologies, television broadcasting is transforming from inefficient tape-based production and distribution to integrated file-based workflows. However, no matter how many changes have took place, successful broadcasting still depends on the ability to deliver a consistent high quality signal to the audiences. After the transition from tape to file, traditional methods of manual quality control (QC) become inadequate, subjective, and inefficient. Based on China Central Television's full file-based workflow in the new site, this paper introduces an automated quality control test system for accurate detection of hidden troubles in media contents. It discusses the system framework and workflow control when the automated QC is added. It puts forward a QC criterion and brings forth a QC software followed this criterion. It also does some experiments on QC speed by adopting parallel processing and distributed computing. The performance of the test system shows that the adoption of automated QC can make the production effective and efficient, and help the station to achieve a competitive advantage in the media market.

  13. Quantitative assessment of computed radiography quality control parameters.

    PubMed

    Rampado, O; Isoardi, P; Ropolo, R

    2006-03-21

    Quality controls for testing the performance of computed radiography (CR) systems have been recommended by manufacturers and medical physicists' organizations. The purpose of this work was to develop a set of image processing tools for quantitative assessment of computed radiography quality control parameters. Automatic image analysis consisted in detecting phantom details, defining regions of interest and acquiring measurements. The tested performance characteristics included dark noise, uniformity, exposure calibration, linearity, low-contrast and spatial resolution, spatial accuracy, laser beam function and erasure thoroughness. CR devices from two major manufacturers were evaluated. We investigated several approaches to quantify the detector response uniformity. We developed methods to characterize the spatial accuracy and resolution properties across the entire image area, based on the Fourier analysis of the image of a fine wire mesh. The implemented methods were sensitive to local blurring and allowed us to detect a local distortion of 4% or greater in any part of an imaging plate. The obtained results showed that the developed image processing tools allow us to implement a quality control program for CR with short processing time and with absence of subjectivity in the evaluation of the parameters. PMID:16510964

  14. Quality Assessment of Randomized Controlled Trials Published in the Korean Journal of Urology Over the Past 20 Years

    PubMed Central

    Lee, Joo Yong; Chung, Jae Hoon; Kang, Dong Hyuk; Lee, Jung Woo; Moon, Hong Sang; Yoo, Tag Keun; Choi, Hong Yong

    2011-01-01

    Purpose Because low-quality trials may lead to erroneous conclusions, quality assessments are necessary. Thus, in this study, we scrutinized randomized controlled trials (RCTs) published in the Korean Journal of Urology (KJU) to assess their quantity and quality. Materials and Methods Upon extracting RCTs from all articles published in the KJU from 1991 to 2010, assessments were made on the basis of the Jadad scale and the adequacy of allocation concealment. The selections and assessments were performed independently by two researchers, and adjustment of the differences was done by a third-party researcher. In addition, the factors that may affect quality were analyzed. Results A total of 3,516 original articles were searched and 28 RCTs were extracted. In the 1990s, RCTs constituted only 0.27% of the total original articles, but in the 2000s, RCTs constituted 1.34%. The mean total Jadad score increased from 1.6 points in the 1990s to 1.65 points in the 2000s. However, the percentage of "good quality" trials also increased from 20% to 30.43%. As for adequate allocation concealment, one study was observed in the 2000s. The aspect most lacking was appropriate dropout and double-blinding. Studies with medical interventions or funded or examined by institutional review boards tended to receive higher quality assessments. Conclusions Although RCTs consistently increased in both quantity and quality, in future studies, researchers should continue to strive toward achieving adequate allocation concealment and appropriate double-blinding. In addition, researchers must become more interested in receiving external funding and undergoing examination by institutional review boards. PMID:22025962

  15. 40 CFR 81.236 - Central Georgia Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 18 2012-07-01 2012-07-01 false Central Georgia Intrastate Air Quality... Quality Control Regions § 81.236 Central Georgia Intrastate Air Quality Control Region. The Central Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  16. 40 CFR 81.236 - Central Georgia Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Central Georgia Intrastate Air Quality... Quality Control Regions § 81.236 Central Georgia Intrastate Air Quality Control Region. The Central Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  17. 40 CFR 81.236 - Central Georgia Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 18 2014-07-01 2014-07-01 false Central Georgia Intrastate Air Quality... Quality Control Regions § 81.236 Central Georgia Intrastate Air Quality Control Region. The Central Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  18. 40 CFR 81.236 - Central Georgia Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Central Georgia Intrastate Air Quality... Quality Control Regions § 81.236 Central Georgia Intrastate Air Quality Control Region. The Central Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  19. 40 CFR 81.236 - Central Georgia Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 18 2013-07-01 2013-07-01 false Central Georgia Intrastate Air Quality... Quality Control Regions § 81.236 Central Georgia Intrastate Air Quality Control Region. The Central Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  20. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the...

  1. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial...

  2. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  3. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial...

  4. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of...

  5. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the...

  6. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist...

  7. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of...

  8. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the...

  9. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of...

  10. 40 CFR 81.14 - Metropolitan Chicago Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.14 Metropolitan Chicago Interstate Air Quality Control Region. The Metropolitan Chicago Interstate Air Quality Control Region (Illinois-Indiana) is revised to consist of...

  11. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  12. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been...

  13. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of...

  14. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial...

  15. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist...

  16. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been...

  17. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of...

  18. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  19. 40 CFR 81.14 - Metropolitan Chicago Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.14 Metropolitan Chicago Interstate Air Quality Control Region. The Metropolitan Chicago Interstate Air Quality Control Region (Illinois-Indiana) is revised to consist of...

  20. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been...

  1. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the...

  2. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial...

  3. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of...

  4. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  5. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the...

  6. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of...

  7. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial...

  8. 40 CFR 81.76 - State of Hawaii Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 18 2012-07-01 2012-07-01 false State of Hawaii Air Quality Control... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.76 State of Hawaii Air Quality Control Region. The State of Hawaii Air...

  9. 40 CFR 81.76 - State of Hawaii Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 18 2013-07-01 2013-07-01 false State of Hawaii Air Quality Control... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.76 State of Hawaii Air Quality Control Region. The State of Hawaii Air...

  10. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist...

  11. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of...

  12. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial...

  13. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the...

  14. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial...

  15. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of...

  16. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  17. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial...

  18. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of...

  19. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  20. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial...

  1. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of...

  2. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the...

  3. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of...

  4. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the...

  5. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the...

  6. 40 CFR 81.76 - State of Hawaii Air Quality Control Region.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 17 2011-07-01 2011-07-01 false State of Hawaii Air Quality Control... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.76 State of Hawaii Air Quality Control Region. The State of Hawaii Air...

  7. 21 CFR 862.1660 - Quality control material (assayed and unassayed).

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Quality control material (assayed and unassayed... Test Systems § 862.1660 Quality control material (assayed and unassayed). (a) Identification. A quality... that may arise from reagent or analytical instrument variation. A quality control material (assayed...

  8. 21 CFR 862.1660 - Quality control material (assayed and unassayed).

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Quality control material (assayed and unassayed... Test Systems § 862.1660 Quality control material (assayed and unassayed). (a) Identification. A quality... that may arise from reagent or analytical instrument variation. A quality control material (assayed...

  9. 40 CFR 81.76 - State of Hawaii Air Quality Control Region.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false State of Hawaii Air Quality Control... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.76 State of Hawaii Air Quality Control Region. The State of Hawaii Air...

  10. Austrian Daily Climate Data Rescue and Quality Control

    NASA Astrophysics Data System (ADS)

    Jurkovic, A.; Lipa, W.; Adler, S.; Albenberger, J.; Lechner, W.; Swietli, R.; Vossberg, I.; Zehetner, S.

    2010-09-01

    Checked climate datasets are a "conditio sine qua non" for all projects that are relevant for environment and climate. In the framework of climate change studies and analysis it is essential to work with quality controlled and trustful data. Furthermore these datasets are used as input for various simulation models. In regard to investigations of extreme events, like strong precipitation periods, drought periods and similar ones we need climate data in high temporal resolution (at least in daily resolution). Because of the historical background - during Second World War the majority of our climate sheets were sent to Berlin, where the historical sheets were destroyed by a bomb attack and so important information got lost - only several climate sheets, mostly duplicates, before 1939 are available and stored in our climate data archive. In 1970 the Central Institute for Meteorology and Geodynamics in Vienna started a first attempt to digitize climate data by means of punch cards. With the introduction of a routinely climate data quality control in 1984 we can speak of high-class-checked daily data (finally checked data, quality flag 6). Our group is working on the processing of digitization and quality control of the historical data for the period 1872 to 1983 for 18 years. Since 2007 it was possible to intensify the work (processes) in the framework of an internal project, namely Austrian Climate Data Rescue and Quality Control. The aim of this initiative was - and still is - to supply daily data in an outstanding good and uniform quality. So this project is a kind of pre-project for all scientific projects which are working with daily data. In addition to routine quality checks (that are running since 1984) using the commercial Bull Software we are testing our data with additional open source software, namely ProClim.db. By the use of this spatial and statistical test procedure, the elements air temperature and precipitation - for several sites in Carinthia - could

  11. [Improvement of routine works and quality control in mycobacterial laboratory].

    PubMed

    Suzuki, Katsuhiro; Higuchi, Takeshi

    2007-03-01

    Many new methods have been introduced into routine laboratory works in microbiology since 1990. Molecular biology, in particular, opened a new era and promoted a technician's skill much. PCR and hybridization technique have been ordinary one in many laboratories. Since old techniques such as smear and culture are still needed, amount of routine works is increasing gradually. Thus, improving efficiency and keeping quality of routine works are becoming more and more important issues. This symposium focused on such points, and four skilled technicians around Japan presented their own tips. 1. Coexistence of M. tuberculosis and M. avium complex (MAC) in the MGIT culture system: Yasushi WATANABE (Clinical Laboratory Division, NHO Nishi-Niigata Chuo National Hospital). Sputum samples of some tuberculosis patients yielded only MAC in the MGIT culture system. Such co-infected cases presented problems to mislead proper treatment and infection control. The detection rate of MAC was significantly high, and the growth speed of MAC was significantly rapid in the MGIT culture system, compared to those of M. tuberculosis. Additionally, M. tuberculosis was not detected with even more quantity than MAC in the small amount of mixed samples. Higher sensitivity and growth speed of MAC are the important characteristics of the MGIT system. 2. Internal quality control with ordinary examination results: Akio AONO (Department of Clinical Examination, Double-Barred Cross Hospital, Japan Anti-Tuberculosis Association). Our laboratory utilizes ordinary examination results as the internal quality control for specimen pretreatment, culture, and drug susceptibility testing. The contamination rate of MGIT culture system is useful for the evaluation of the decontamination process. It was 6.3% on average in our laboratory in 2005. The number of drug resistant strains is also useful to assess the performance of drug susceptibility testing. The incidence of each anti-tuberculosis drug resistance

  12. Online Error Reporting for Managing Quality Control Within Radiology.

    PubMed

    Golnari, Pedram; Forsberg, Daniel; Rosipko, Beverly; Sunshine, Jeffrey L

    2016-06-01

    Information technology systems within health care, such as picture archiving and communication system (PACS) in radiology, can have a positive impact on production but can also risk compromising quality. The widespread use of PACS has removed the previous feedback loop between radiologists and technologists. Instead of direct communication of quality discrepancies found for an examination, the radiologist submitted a paper-based quality-control report. A web-based issue-reporting tool can help restore some of the feedback loop and also provide possibilities for more detailed analysis of submitted errors. The purpose of this study was to evaluate the hypothesis that data from use of an online error reporting software for quality control can focus our efforts within our department. For the 372,258 radiologic examinations conducted during the 6-month period study, 930 errors (390 exam protocol, 390 exam validation, and 150 exam technique) were submitted, corresponding to an error rate of 0.25 %. Within the category exam protocol, technologist documentation had the highest number of submitted errors in ultrasonography (77 errors [44 %]), while imaging protocol errors were the highest subtype error for computed tomography modality (35 errors [18 %]). Positioning and incorrect accession had the highest errors in the exam technique and exam validation error category, respectively, for nearly all of the modalities. An error rate less than 1 % could signify a system with a very high quality; however, a more likely explanation is that not all errors were detected or reported. Furthermore, staff reception of the error reporting system could also affect the reporting rate. PMID:26510753

  13. Quality control of the RMS US flood model

    NASA Astrophysics Data System (ADS)

    Jankowfsky, Sonja; Hilberts, Arno; Mortgat, Chris; Li, Shuangcai; Rafique, Farhat; Rajesh, Edida; Xu, Na; Mei, Yi; Tillmanns, Stephan; Yang, Yang; Tian, Ye; Mathur, Prince; Kulkarni, Anand; Kumaresh, Bharadwaj Anna; Chaudhuri, Chiranjib; Saini, Vishal

    2016-04-01

    The RMS US flood model predicts the flood risk in the US with a 30 m resolution for different return periods. The model is designed for the insurance industry to estimate the cost of flood risk for a given location. Different statistical, hydrological and hydraulic models are combined to develop the flood maps for different return periods. A rainfall-runoff and routing model, calibrated with observed discharge data, is run with 10 000 years of stochastic simulated precipitation to create time series of discharge and surface runoff. The 100, 250 and 500 year events are extracted from these time series as forcing for a two-dimensional pluvial and fluvial inundation model. The coupling of all the different models which are run on the large area of the US implies a certain amount of uncertainty. Therefore, special attention is paid to the final quality control of the flood maps. First of all, a thorough quality analysis of the Digital Terrain model and the river network was done, as the final quality of the flood maps depends heavily on the DTM quality. Secondly, the simulated 100 year discharge in the major river network (600 000 km) is compared to the 100 year discharge derived using extreme value distribution of all USGS gauges with more than 20 years of peak values (around 11 000 gauges). Thirdly, for each gauge the modelled flood depth is compared to the depth derived from the USGS rating curves. Fourthly, the modelled flood depth is compared to the base flood elevation given in the FEMA flood maps. Fifthly, the flood extent is compared to the FEMA flood extent. Then, for historic events we compare flood extents and flood depths at given locations. Finally, all the data and spatial layers are uploaded on geoserver to facilitate the manual investigation of outliers. The feedback from the quality control is used to improve the model and estimate its uncertainty.

  14. Quality Assurance and Quality Control in Point-of-Care Testing.

    PubMed

    Newman, Ashleigh W; Behling-Kelly, Erica

    2016-03-01

    With advancements in the standard of care in veterinary medicine and instrument technology, performing in-house laboratory work on a variety of point-of-care instruments, ranging from glucometers to benchtop chemistry analyzers, has become increasingly commonplace. However, the ability of an instrument to perform a test does not guarantee that those results are accurate. Ensuring that your in-clinic laboratory is providing reliable data requires a comprehensive plan that encompasses both common sense practices aimed at preventing errors at each stage of the testing process, as well as standard operating procedures to validate and monitor analyzer performance. These 2 arms of the plan are known as quality assurance and quality control. Although these concepts are typically out of the comfort zone for veterinarians, just as the thought of business management may deter some veterinarians from practice ownership, it is not beyond the capabilities of veterinarians to learn, understand, and incorporate them into their practice. The objectives of this article are to convey the importance of quality assurance and quality control, walk you through the American Society for Veterinary Clinical Pathology guidelines on this topic, and provide direction to additional resources for further education on this topic, all with the focus on point-of-care testing in the in-clinic laboratory. PMID:27451043

  15. New automated quality control of phenological data in Switzerland

    NASA Astrophysics Data System (ADS)

    Pietragalla, Barbara; Knechtl, Valentin; Sigg, Christian; Clot, Bernard

    2016-04-01

    Phenological observations are considered important indicators of climate change. Therefore, reliable data is a crucial requirement. In 2015 MeteoSwiss has developed an automated quality control for phenological data that runs weekly to check the incoming data. The aim is to detect implausible data. The implausible values are further examined manually. The Swiss Phenology Network, initiated in 1951, consists of about 160 stations observing 69 phenological parameters from 26 species. In 2015 the network generated 6475 values of onset dates. For the recognition of implausible data, linear models are used. For each of the phenological parameters that should be verified the most predictive parameters have been determined in correlation tests. Up to four different parameters are used as predictive variables. The three main predictive parameters are the mean onset date of the respective phenophase (at that specific station), the cumulated daily mean temperature and an additional phenological parameter with the highest correlation. The model uses a defined sequence of steps, which can handle the absence of additional predictive phenological parameters (in case that in spring time some of these phenophases are not yet available). The model output is a predicted date which can be compared with the observed onset date that undergoes the quality control. The magnitude of this deviation decides, if a value is regarded as potentially problematic. An additional quality check examines if the natural sequence of the phenophases within a species is correct, for example that the date of the "begin of flowering" occurs before the "full flowering". The output of the automated quality control is a list of flagged values of potentially erroneous data that have to be examined manually in a second step. To facilitate the expert's decision whether a value is correct or wrong, a report is automatically created, showing the data graphically and in comparison with other stations of the same

  16. Quality control on crimping of large diameter welding pipe

    NASA Astrophysics Data System (ADS)

    Fan, Lifeng; Gao, Ying; Li, Qiang; Xu, Hongshen

    2012-11-01

    Crimping is used in production of large diameter submerged-arc welding pipes. Many researches are focused on crimping in certain manufacturing mode of welding pipe. The application scopes of research achievements become limited due to lack of uniformity in theoretical analysis. In order to propose a crimping prediction method in order to control forming quality, the theory model of crimping based on elastic-plastic mechanics is established. The main technical parameters are determined by theoretical analysis, including length of crimping, base radius of punch, terminal angle of punch, base radius of die, terminal angle of die and horizontal distance between punch and die. In addition, a method used to evaluate the forming quality is presented, which investigates the bending angle after springback, forming force, straight edge length and equivalent radius of curvature. In order to investigate the effects of technical parameters on forming quality, a two-dimensional finite element model is established by finite element software ABAQUS. The finite element model is verified in that its shapes error is less than 5% by comparable experiments, which shows that their geometric precision meets demand. The crimping characteristics is obtained, such as the distribution of stress and strain and the changes of forming force, and the relation curves of technical parameters on forming quality are given by simulation analysis. The sensitivity analysis indicates that the effects of length of crimping, technical parameters of punch on forming quality are significant. In particular, the data from simulation analysis are regressed by response surface method (RSM) to establish prediction model. The feasible technical parameters are obtained from the prediction model. This method presented provides a new thought used to design technical parameters of crimping forming and makes a basis for improving crimping forming quality.

  17. WELDSMART: A vision-based expert system for quality control

    NASA Astrophysics Data System (ADS)

    Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

    1992-09-01

    This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and

  18. WELDSMART: A vision-based expert system for quality control

    NASA Technical Reports Server (NTRS)

    Andersen, Kristinn; Barnett, Robert Joel; Springfield, James F.; Cook, George E.

    1992-01-01

    This work was aimed at exploring means for utilizing computer technology in quality inspection and evaluation. Inspection of metallic welds was selected as the main application for this development and primary emphasis was placed on visual inspection, as opposed to other inspection methods, such as radiographic techniques. Emphasis was placed on methodologies with the potential for use in real-time quality control systems. Because quality evaluation is somewhat subjective, despite various efforts to classify discontinuities and standardize inspection methods, the task of using a computer for both inspection and evaluation was not trivial. The work started out with a review of the various inspection techniques that are used for quality control in welding. Among other observations from this review was the finding that most weld defects result in abnormalities that may be seen by visual inspection. This supports the approach of emphasizing visual inspection for this work. Quality control consists of two phases: (1) identification of weld discontinuities (some of which may be severe enough to be classified as defects), and (2) assessment or evaluation of the weld based on the observed discontinuities. Usually the latter phase results in a pass/fail judgement for the inspected piece. It is the conclusion of this work that the first of the above tasks, identification of discontinuities, is the most challenging one. It calls for sophisticated image processing and image analysis techniques, and frequently ad hoc methods have to be developed to identify specific features in the weld image. The difficulty of this task is generally not due to limited computing power. In most cases it was found that a modest personal computer or workstation could carry out most computations in a reasonably short time period. Rather, the algorithms and methods necessary for identifying weld discontinuities were in some cases limited. The fact that specific techniques were finally developed and

  19. A suite of RS/1 procedures for chemical laboratory statistical quality control and Shewhart control charting

    SciTech Connect

    Shanahan, K.L.

    1990-09-01

    A suite of RS/1 procedures for Shewhart control charting in chemical laboratories is described. The suite uses the RS series product QCA (Quality Control Analysis) for chart construction and analysis. The suite prompts users for data in a user friendly fashion and adds the data to or creates the control charts. All activities are time stamped. Facilities for generating monthly or contiguous time segment summary charts are included. The suite is currently in use at Westinghouse Savannah River Company.

  20. Quality Control Procedures for Genome Wide Association Studies

    PubMed Central

    Turner, Stephen; Armstrong, Loren L.; Bradford, Yuki; Carlson, Christopher S.; Crawford, Dana C.; Crenshaw, Andrew T.; de Andrade, Mariza; Doheny, Kimberly F.; Haines, Jonathan L.; Hayes, Geoffrey; Jarvik, Gail; Jiang, Lan; Kullo, Iftikhar J.; Li, Rongling; Ling, Hua; Manolio, Teri A.; Matsumoto, Martha; McCarty, Catherine A.; McDavid, Andrew N.; Mirel, Daniel B.; Paschall, Justin E.; Pugh, Elizabeth W.; Rasmussen, Luke V.; Wilke, Russell A.; Zuvich, Rebecca L.; Ritchie, Marylyn D.

    2011-01-01

    Genome-wide association studies (GWAS) are being conducted at an unprecedented rate in population-based cohorts and have increased our understanding of the pathophysiology of complex disease. The recent application of GWAS to clinic-based cohorts has also yielded genetic predictors of clinical outcomes. Regardless of context, the practical utility of this information will ultimately depend upon the quality of the original data. Quality control (QC) procedures for GWAS are computationally intensive, operationally challenging, and constantly evolving. With each new dataset, new realities are discovered about GWAS data and best practices continue to be developed. The Genomics Workgroup of the National Human Genome Research Institute (NHGRI) funded electronic Medical Records and Genomics (eMERGE) network has invested considerable effort in developing strategies for QC of these data. The lessons learned by this group will be valuable for other investigators dealing with large scale genomic datasets. Here we enumerate some of the challenges in QC of GWAS data and describe the approaches that the eMERGE network is using for quality assurance in GWAS data, thereby minimizing potential bias and error in GWAS results. In this protocol we discuss common issues associated with QC of GWAS data, including data file formats, software packages for data manipulation and analysis, sex chromosome anomalies, sample identity, sample relatedness, population substructure, batch effects, and marker quality. We propose best practices and discuss areas of ongoing and future research. PMID:21234875