Science.gov

Sample records for admissible fixture designs

  1. Processor and method for developing a set of admissible fixture designs for a workpiece

    DOEpatents

    Brost, Randolph C.; Goldberg, Kenneth Y.; Wallack, Aaron S.; Canny, John

    1996-01-01

    A fixture process and method is provided for developing a complete set of all admissible fixture designs for a workpiece which prevents the workpiece from translating or rotating. The fixture processor generates the set of all admissible designs based on geometric access constraints and expected applied forces on the workpiece. For instance, the fixture processor may generate a set of admissible fixture designs for first, second and third locators placed in an array of holes on a fixture plate and a translating clamp attached to the fixture plate for contacting the workpiece. In another instance, a fixture vice is used in which first, second, third and fourth locators are used and first and second fixture jaws are tightened to secure the workpiece. The fixture process also ranks the set of admissible fixture designs according to a predetermined quality metric so that the optimal fixture design for the desired purpose may be identified from the set of all admissible fixture designs.

  2. Processor and method for developing a set of admissible fixture designs for a workpiece

    DOEpatents

    Brost, R.C.; Goldberg, K.Y.; Wallack, A.S.; Canny, J.

    1996-08-13

    A fixture process and method is provided for developing a complete set of all admissible fixture designs for a workpiece which prevents the workpiece from translating or rotating. The fixture processor generates the set of all admissible designs based on geometric access constraints and expected applied forces on the workpiece. For instance, the fixture processor may generate a set of admissible fixture designs for first, second and third locators placed in an array of holes on a fixture plate and a translating clamp attached to the fixture plate for contacting the workpiece. In another instance, a fixture vice is used in which first, second, third and fourth locators are used and first and second fixture jaws are tightened to secure the workpiece. The fixture process also ranks the set of admissible fixture designs according to a predetermined quality metric so that the optimal fixture design for the desired purpose may be identified from the set of all admissible fixture designs. 27 figs.

  3. Processor and method for developing a set of admissible fixture designs for a workpiece

    DOEpatents

    Brost, R.C.; Goldberg, K.Y.; Canny, J.; Wallack, A.S.

    1999-01-05

    Methods and apparatus are provided for developing a complete set of all admissible Type 1 and Type 2 fixture designs for a workpiece. The fixture processor generates the set of all admissible designs based on geometric access constraints and expected applied forces on the workpiece. For instance, the fixture processor may generate a set of admissible fixture designs for first, second and third locators placed in an array of holes on a fixture plate and a translating clamp attached to the fixture plate for contacting the workpiece. In another instance, a fixture vise is used in which first, second, third and fourth locators are used and first and second fixture jaws are tightened to secure the workpiece. The fixture process also ranks the set of admissible fixture designs according to a predetermined quality metric so that the optimal fixture design for the desired purpose may be identified from the set of all admissible fixture designs. 44 figs.

  4. Processor and method for developing a set of admissible fixture designs for a workpiece

    DOEpatents

    Brost, Randolph C.; Goldberg, Kenneth Y.; Canny, John; Wallack, Aaron S.

    1999-01-01

    Methods and apparatus are provided for developing a complete set of all admissible Type I and Type II fixture designs for a workpiece. The fixture processor generates the set of all admissible designs based on geometric access constraints and expected applied forces on the workpiece. For instance, the fixture processor may generate a set of admissible fixture designs for first, second and third locators placed in an array of holes on a fixture plate and a translating clamp attached to the fixture plate for contacting the workpiece. In another instance, a fixture vise is used in which first, second, third and fourth locators are used and first and second fixture jaws are tightened to secure the workpiece. The fixture process also ranks the set of admissible fixture designs according to a predetermined quality metric so that the optimal fixture design for the desired purpose may be identified from the set of all admissible fixture designs.

  5. Tool and Fixture Design

    SciTech Connect

    Graham, Mark W.

    2015-07-28

    In a manufacturing process, a need is identified and a product is created to fill this need. While design and engineering of the final product is important, the tools and fixtures that aid in the creation of the final product are just as important, if not more so. Power supplies assembled at the TA-55 PF-5 have been designed by an excellent engineering team. The task in PF-5 now is to ensure that all steps of the assembly and manufacturing process can be completed safely, reliably, and in a quality repeatable manner. One of these process steps involves soldering fine wires to an electrical connector. During the process development phase, the method of soldering included placing the power supply in a vice in order to manipulate it into a position conducive to soldering. This method is unacceptable from a reliability, repeatability, and ergonomic standpoint. To combat these issues, a fixture was designed to replace the current method. To do so, a twelve step engineering design process was used to create the fixture that would provide a solution to a multitude of problems, and increase the safety and efficiency of production.

  6. A CAD tool that automatically designs fixtures and pallets

    SciTech Connect

    Brost, R.C.; Peters, R.R.

    1995-12-01

    Costs associated with designing and fabricating fixtures may be a significant portion of the total costs associated with a manufacturing task. The software tool, HoldFast, designs optimal fixtures that hold a single workpiece, are easily fabricated, provide rigid constraint and deterministic location of the workpiece, are robust to workpiece shape variations, obey all associated task constraints, and are easy to load and unload. We illustrate the capabilities of HoldFast by designing fixtures for several examples. Fixtures are designed and built for finish-machining and drilling of a cast part for prototype fabrication and mass-production fabrication. A pallet fixture is designed for vertical assembly of a personal cassette player. Another pallet fixture is designed and built that will hold either the personal cassette player or a glue gun during assembly.

  7. Automatic design of 3-d fixtures and assembly pallets

    SciTech Connect

    Brost, R.C.; Peters, R.R.

    1995-12-31

    This paper presents an implemented algorithm that automatically designs fixtures and assembly pallets to hold three-dimensional parts. The designed fixtures rigidly constrain and locate the part, obey task constraints, are robust to part shape variations, are easy to load, and are economical to produce. The algorithm is guaranteed to find the global optimum solution that satisfies these and other pragmatic conditions. We present the results of the algorithm applied to several practical manufacturing problems. For these complex problems the algorithm typically returns initial high-quality fixture designs in less than two minutes, and identifies th global optimum design in just over an hour.

  8. Automatic design of 3-d fixtures and assembly pallets

    SciTech Connect

    Brost, R.C.; Peters, R.R.

    1997-01-01

    This paper presents an implemented algorithm that automatically designs fixtures and assembly pallets to hold three-dimensional parts. All fixtures generated by the algorithm employ round side locators, a side clamp, and cylindrical supports; depending on the value of an input control flag, the fixture may also include swing-arm top clamps. Using these modular elements, the algorithm designs fixtures that rigidly constrain and locate the part, obey task constraints, are robust to part shape variations, are easy to load, and are economical to produce. For the class of fixtures that are considered, the algorithm is guaranteed to find the global optimum design that satisfies these and other pragmatic conditions. The authors present the results of the algorithm applied to several practical manufacturing problems. For these complex problems the algorithm typically returns initial high-quality fixture designs in less than a minute, and identifies the global optimum design in just over an hour. The algorithm is also capable of solving difficult design problems where a single fixture is desired that can hold either of two parts.

  9. Test fixture design for boron-aluminum and beryllium test panels

    NASA Technical Reports Server (NTRS)

    Breaux, C. G.

    1973-01-01

    A detailed description of the test fixture design and the backup analysis of the fixture assembly and its components are presented. The test fixture is required for the separate testing of two boron-aluminum and two beryllium compression panels. This report is presented in conjunction with a complete set of design drawings on the test fixture system.

  10. The design of bearing processing technology and fixture

    NASA Astrophysics Data System (ADS)

    Liu, Sibo

    2017-03-01

    This paper is designed for bearing processing technology and fixture. The main task is to work out the half fine milling under 36mm, Φ18 holes, bearing the processing technology of the rules of procedure, and write CARDS. Its parts are casting, which is small and of simple structure. Moreover, the components of the hole processing is higher than that of the surface, so the processing order of surface first is taken. The fixture special jig is adopted in each working procedure, among which in a drill Φ18 holes, the hydraulic clamping is used, which is simple, convenient and can meet the requirements.

  11. Fixture design for seismometer testing on the shake table

    NASA Astrophysics Data System (ADS)

    Ma, J.

    2013-12-01

    Using shake table is one of the effective measures for calibration and testing of seismometer. Ultra-low frequency shake table equipped with laser vibrometer adopts air-bearing slider and displacement-based feedback in China Earthquake Networks Seismometer Testing Center. This essential equipment possesses the characteristics of low frequency, long stroke and low distortion, whereas the resonance and the angular deviation strongly influence the measurement results. The former is generated from the loose couple between the seismometer and table board and the latter from the difference between motion direction and sensitive axis of the seismometer when shake table moves in the horizontal directions. This study aims to design a fixture for testing to improve the measuring accuracy and meet the testing requirement for the seismometer of jumbo size. Three-dimensional solid modeling software of Pro/Engineer Wildfire is used to build the model of vibration fixture. The model is imported into ANSYS with seamless interface between Pro/E and ANSYS and analyzed with finite element method. After multiple calculation and calibration, optimization models are finalized for the vibration fixtures on horizontal and vertical table boards. Material objects are manufactured based on the models. Shake table testing suggests the fixtures effectively satisfy the requirements of inherent frequency over 160Hz, degree of displacement distortion lower than 1% and lateral acceleration ratio less than 3%. In practical testing, accurate azimuth angle is obtained reliably and close coupling is realized between the seismometer and the table board, which provides better testing data.

  12. Fixture Design for Motion Picture and Theatrical Lighting

    NASA Astrophysics Data System (ADS)

    Dandridge, Susan

    1987-02-01

    I am the Marketing Manager for a fairly good-sized company in a very small industry which is dependent on the efforts of the kind of people attending this conference. Strand Lighting and other companies like mine supply the lighting needs of the entertainment industry. We listen to people like Dan Flannery and Bran Ferrren as well as thousands of other creative, artistic designers, manufacturing the tools they need to bring you everything from Hamlet to Dynasty, from Masterpiece Theatre to The Price is Right. We design and manufacture dimmers, computerized control equipment for the dimmers, and lighting fixtures.It it the issue of lighting fixtures for our industry that brings me here today. The total yearly volume of the entire entertainment lighting industry is estimated at only $70 million. Compare that to the billions of the defense or medical industries.

  13. A Practical Approach for Integrating Automatically Designed Fixtures with Automated Assembly Planning

    SciTech Connect

    Calton, Terri L.; Peters, Ralph R.

    1999-07-20

    This paper presents a practical approach for integrating automatically designed fixtures with automated assembly planning. Product assembly problems vary widely; here the focus is on assemblies that are characterized by a single base part to which a number of smaller parts and subassemblies are attached. This method starts with three-dimension at CAD descriptions of an assembly whose assembly tasks require a fixture to hold the base part. It then combines algorithms that automatically design assembly pallets to hold the base part with algorithms that automatically generate assembly sequences. The designed fixtures rigidly constrain and locate the part, obey task constraints, are robust to part shape variations, are easy to load, and are economical to produce. The algorithm is guaranteed to find the global optimum solution that satisfies these and other pragmatic conditions. The assembly planner consists of four main elements: a user interface, a constraint system, a search engine, and an animation module. The planner expresses all constraints at a sequencing level, specifying orders and conditions on part mating operations in a number of ways. Fast replanning enables an interactive plan-view-constrain-replan cycle that aids in constrain discovery and documentation. The combined algorithms guarantee that the fixture will hold the base part without interfering with any of the assembly operations. This paper presents an overview of the planners, the integration approach, and the results of the integrated algorithms applied to several practical manufacturing problems. For these problems initial high-quality fixture designs and assembly sequences are generated in a matter of minutes with global optimum solutions identified in just over an hour.

  14. A complete algorithm for synthesizing modular fixtures for polygonal parts

    SciTech Connect

    Brost, R.C.; Goldberg, K.Y.

    1993-11-01

    Commercially-available nuclear fixturing systems typically include a square lattice of tapped and bushed holes with precision locating and clamping elements that can be rigidly attached to the lattice using dowel pins or expanding mandrels. Currently, human expertise is required to synthesize a suitable arrangements of these elements to hold a given part. Besides being time consuming, if the set of alternatives is not systematically explored, the designer may fail to find an acceptable fixture or may settle upon a suboptimal fixture. We consider a class of modular fixtures that prevent a part from translating or rotting in the plane using four point contacts on the part`s boundary. These fixtures are based on three round locators, each centered on a lattice point, and one translating clamp. We present an algorithm that accepts a polygonal part shape as input and synthesizes the set of all fixture designs that achieve form closure for the given part. The algorithm also allows the user to specify geometric access constraints on fixtures. If the part has n edges and its maximal diameter is d lattice units, the asymptotic running time of the algorithm is O(n{sup 5}d{sup 5}). We have implemented the algorithm and present example fixtures that it has synthesized. This implementation includes a metric to rank fixtures based on their ability to resist applied forces. We believe this is the first fixture synthesize algorithm that is complete in the sense that it is guaranteed to find an admissible fixture if one exists. Furthermore, the algorithm is guaranteed to find the optimal fixture, relative to any well-defined quality metric.

  15. Visualization of the Newly Designed Jig and Fixture for Computer-Assisted Knee Replacement Surgery

    NASA Astrophysics Data System (ADS)

    Ramli, Intan Syaherra; Arshad, Haslina; Sulong, Abu Bakar; Mohd. Yahaya, Nor Hamdan; Che Haron, Che Hassan

    Surgical training systems based on virtual reality (VR) are highly desired as they offer a cost effective and efficient alternative compared to traditional training methods. Traditional surgical training methods require cadavers or plastic models which are costly. Cadavers cannot be used repeatedly and training with plastic models cannot provide the realistic experience. This paper describes a visualization to show the use of newly design jig and fixture for computer-assisted knee replacement surgery. Orthopedic surgeons found it difficult to align the existing jig with the computer-assisted device during the operation and it is time consuming to place it at the right position. A newly design jig and fixture has been proposed to solve this problem. Visualization is needed to show the surgeons on how it will be used in the computer-assisted knee replacement surgery. Virtual models used in this visualization are constructed from the actual equipment and real human dataset.

  16. Development of a Prediction Model Based on RBF Neural Network for Sheet Metal Fixture Locating Layout Design and Optimization.

    PubMed

    Wang, Zhongqi; Yang, Bo; Kang, Yonggang; Yang, Yuan

    2016-01-01

    Fixture plays an important part in constraining excessive sheet metal part deformation at machining, assembly, and measuring stages during the whole manufacturing process. However, it is still a difficult and nontrivial task to design and optimize sheet metal fixture locating layout at present because there is always no direct and explicit expression describing sheet metal fixture locating layout and responding deformation. To that end, an RBF neural network prediction model is proposed in this paper to assist design and optimization of sheet metal fixture locating layout. The RBF neural network model is constructed by training data set selected by uniform sampling and finite element simulation analysis. Finally, a case study is conducted to verify the proposed method.

  17. Calibration Fixture For Anemometer Probes

    NASA Technical Reports Server (NTRS)

    Lewis, Charles R.; Nagel, Robert T.

    1993-01-01

    Fixture facilitates calibration of three-dimensional sideflow thermal anemometer probes. With fixture, probe oriented at number of angles throughout its design range. Readings calibrated as function of orientation in airflow. Calibration repeatable and verifiable.

  18. Design of a Multi-DOF Tuned Mounting Fixture for the Navy’s Mediumweight Shock Machine

    DTIC Science & Technology

    1993-06-01

    undertest since it would not excite the higher resonant frequencies that may be present in the equipment. As noted in Corbell (1992), a finite element...RESPONSE Extending the concept developed by Chalmers and Shaw (1989), Corbell proposed that a two degree-of-freedom (DOF) fixture could be designed for the...can be used to tune the fixture to the required stiffness, K. From the shock spectrum shown in Figure 7, Corbell chose 60 Hz and 155 Hz as the system

  19. Fixing the fixtures

    SciTech Connect

    Siminovitch, M.; Mills, E.

    1994-11-01

    this article describes fixtures designed explicitly for the compact fluorescent lamp. They offer an effective and permanent solution to energy efficient residential lighting. Topics include advantages of pin-based dedicated fixtures; CFL ups and downs orientation; taking advantage of technology; moving the market.

  20. Design, analysis, and fabrication of a pressure box test fixture for tension damage tolerance testing of curved fuselage panels

    NASA Technical Reports Server (NTRS)

    Smith, P. J.; Bodine, J. B.; Preuss, C. H.; Koch, W. J.

    1993-01-01

    A pressure box test fixture was designed and fabricated to evaluate the effects of internal pressure, biaxial tension loads, curvature, and damage on the fracture response of composite fuselage structure. Previous work in composite fuselage tension damage tolerance, performed during NASA contract NAS1-17740, evaluated the above effects on unstiffened panels only. This work extends the tension damage tolerance testing to curved stiffened fuselage crown structure that contains longitudinal stringers and circumferential frame elements. The pressure box fixture was designed to apply internal pressure up to 20 psi, and axial tension loads up to 5000 lb/in, either separately or simultaneously. A NASTRAN finite element model of the pressure box fixture and composite stiffened panel was used to help design the test fixture, and was compared to a finite element model of a full composite stiffened fuselage shell. This was done to ensure that the test panel was loaded in a similar way to a panel in the full fuselage shell, and that the fixture and its attachment plates did not adversely affect the panel.

  1. Design, fabrication, and initial test of a fixture for reducing the natural frequency of the Mod-O wind turbine tower

    NASA Technical Reports Server (NTRS)

    Winemiller, J. R.; Sullivan, T. L.; Sizemore, R. L.; Yee, S. T.

    1979-01-01

    It was desired to observe the behavior of a two bladed wind turbine where the tower first bending natural frequency is less than twice the rotor speed. The system then passes through resonance when accelerating to operating speed. The frequency of the original Mod-O tower was reduced by placing it on a spring fixture. The fixture is adjustable to provide a range of tower bending frequencies. Fixture design details are given and behavior during initial operation is described.

  2. Samus Toroid Installation Fixture

    SciTech Connect

    Stredde, H.; /Fermilab

    1990-06-27

    The SAMUS (Small Angle Muon System) toroids have been designed and fabricated in the USSR and delivered to D0 ready for installation into the D0 detector. These toroids will be installed into the aperture of the EF's (End Toroids). The aperture in the EF's is 72-inch vertically and 66-inch horizontally. The Samus toroid is 70-inch vertically by 64-inch horizontally by 66-inch long and weighs approximately 38 tons. The Samus toroid has a 20-inch by 20-inch aperture in the center and it is through this aperture that the lift fixture must fit. The toroid must be 'threaded' through the EF aperture. Further, the Samus toroid coils are wound about the vertical portion of the aperture and thus limit the area where a lift fixture can make contact and not damage the coils. The fixture is designed to lift along a surface adjacent to the coils, but with clearance to the coil and with contact to the upper steel block of the toroid. The lift and installation will be done with the 50 ton crane at DO. The fixture was tested by lifting the Samus Toroid 2-inch off the floor and holding the weight for 10 minutes. Deflection was as predicted by the design calculations. Enclosed are sketches of the fixture and it relation to both Toroids (Samus and EF), along with hand calculations and an Finite Element Analysis. The PEA work was done by Kay Weber of the Accelerator Engineering Department.

  3. Wire Test Grip Fixture

    NASA Technical Reports Server (NTRS)

    Burke, Christopher S.

    2011-01-01

    Wire-testing issues, such as the gripping strains imposed on the wire, play a critical role in obtaining clean data. In a standard test frame fitted with flat wedge grips, the gripping action alone creates stresses on the wire specimen that cause the wire to fail at the grip location. A new test frame, which is outfitted with a vacuum chamber, negated the use of any conventional commercially available wire test fixtures, as only 7 in. (17.8 cm) existed between the grip faces. An innovative grip fixture was designed to test thin gauge wire for a variety of applications in an existing Instron test frame outfitted with a vacuum chamber.

  4. Design of a Combined Ballistic Simulator and Primer Force Experimental Fixture

    DTIC Science & Technology

    2015-08-01

    innovative methods used to research propellant ignition during the gun cycle have been combined into a single experimental fixture. The first...technique uses a force gauge behind the breech to measure the force acting in the primer cup, which should approximate breech pressure in the gun . These...where the base of the bullet would be in a gun and allows force acting in the primer cup to be measured while using a transparent chamber to view flame

  5. Samus Counter Lifting Fixture

    SciTech Connect

    Stredde, H.; /Fermilab

    1998-05-27

    A lifting fixture has been designed to handle the Samus counters. These counters are being removed from the D-zero area and will be transported off site for further use at another facility. This fixture is designed specifically for this particular application and will be transferred along with the counters. The future use of these counters may entail installation at a facility without access to a crane and therefore a lift fixture suitable for both crane and/or fork lift usage has been created The counters weigh approximately 3000 lbs. and have threaded rods extended through the counter at the top comers for lifting. When these counters were first handled/installed these rods were used in conjunction with appropriate slings and handled by crane. The rods are secured with nuts tightened against the face of the counter. The rod thread is M16 x 2({approx}.625-inch dia.) and extends 2-inch (on average) from the face of the counter. It is this cantilevered rod that the lift fixture engages with 'C' style plates at the four top comers. The strongback portion of the lift fixture is a steel rectangular tube 8-inch (vertical) x 4-inch x .25-inch wall, 130-inch long. 1.5-inch square bars are welded perpendicular to the long axis of the rectangular tube at the appropriate lift points and the 'C' plates are fastened to these bars with 3/4-10 high strength bolts -grade 8. Two short channel sections are positioned-welded-to the bottom of the rectangular tube on 40 feet centers, which are used as locators for fork lift tines. On the top are lifting eyes for sling/crane usage and are rated at 3500 lbs. safe working load each - vertical lift only.

  6. Space assembly fixtures and aids

    NASA Technical Reports Server (NTRS)

    Bloom, K. A.; Lillenas, A. N.

    1980-01-01

    Concepts and requirements for assembly fixtures and aids necessary for the assembly and maintenance of spare platforms were studied. Emphasis was placed on erectable and deployable type structures with the shuttle orbiter as the assembly base. Both single and multiple orbiter flight cases for the platform assembly were considered. Applicable space platform assembly studies were reviewed to provide a data base for establishing the assembly fixture and aids design requirements, assembly constraints, and the development of representative design concepts. Conclusions indicated that fixture requirements will vary with platform size. Larger platforms will require translation relative to the orbiter RMS working volume. The installation of platform payloads and subsystems (e.g., utility distribution) must also be considered in the specification of assembly fixtures and aids.

  7. Calibration Fixture For Welding Robot

    NASA Technical Reports Server (NTRS)

    Holly, Krisztina J.

    1990-01-01

    Compact, lightweight device used in any position or orientation. Calibration fixture designed for use on robotic gas/tungsten-arc welding torch equipped with vision-based seam-tracking system. Through optics in hollow torch cylinder, video camera obtains image of weld, viewing along line of sight coaxial with welding electrode. Attaches to welding-torch cylinder in place of gas cup normally attached in use. By use of longer or shorter extension tube, fixture accommodates welding electrode of unusual length.

  8. Specimens and Reusable Fixturing for Testing Advanced Aeropropulsion Materials Under In-Plane Biaxial Loading. Part 1; Results of Conceptual Design Study

    NASA Technical Reports Server (NTRS)

    Ellis, J. R.; Sandlass, G. S.; Bayyari, M.

    2001-01-01

    A design study was undertaken to investigate the feasibility of using simple specimen designs and reusable fixturing for in-plane biaxial tests planned for advanced aeropropulsion materials. Materials of interest in this work include: advanced metallics, polymeric matrix composites, metal and intermetallic matrix composites, and ceramic matrix composites. Early experience with advanced metallics showed that the cruciform specimen design typically used in this type of testing was impractical for these materials, primarily because of concerns regarding complexity and cost. The objective of this research was to develop specimen designs, fixturing, and procedures which would allow in-plane biaxial tests to be conducted on a wide range of aeropropulsion materials while at the same time keeping costs within acceptable limits. With this goal in mind. a conceptual design was developed centered on a specimen incorporating a relatively simple arrangement of slots and fingers for attachment and loading purposes. The ANSYS finite element code was used to demonstrate the feasibility of the approach and also to develop a number of optimized specimen designs. The same computer code was used to develop the reusable fixturing needed to position and grip the specimens in the load frame. The design adopted uses an assembly of slotted fingers which can be reconfigured as necessary to obtain optimum biaxial stress states in the specimen gage area. Most recently, prototype fixturing was manufactured and is being evaluated over a range of uniaxial and biaxial loading conditions.

  9. Magnetic-Bearing Test Fixture

    NASA Technical Reports Server (NTRS)

    Groom, Nelson J.; Poole, William L.

    1991-01-01

    Microcomputer-controlled magnetic-bearing test fixture used to develop approaches to design of controls for magnetic bearing actuators designed and constructed. Includes load cells connected to bar, in turn, connected through screw positioners to geared drive motors. Position of equivalent suspended element sensed by position sensors and controlled by drive motors. Provides control of gap in magnetic bearing and of current in electromagnet coil. Measurements made include magnetic-bearing gaps, magnetic flux in bearing gaps, and bearing forces. Approaches to linearization and control developed by use of fixture applicable to wide range of small-gap suspension systems.

  10. 24 CFR 3280.607 - Plumbing fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Plumbing Systems § 3280.607 Plumbing fixtures... fixture or appliance. (See also § 3280.607(b)(4)(ii).) (6) Water conservation. All lavatory faucets... their intended use. (2) Water closets. (i) Water closets shall be designed and manufactured according...

  11. Design and Calibration of Custom Flowfield/Rake for the F-15B Propulsion Flight Test Fixture

    NASA Technical Reports Server (NTRS)

    Flynn, Darin C.; Ratnayake, Nalin A.; Frederick, Mike

    2008-01-01

    The Propulsion Flight Test Fixture (PFTF) system at NASA Dryden Flight Research Center (DFRC) provides an innovative and cost effective method of flight testing advanced propulsion concepts and components in a relevant environment using DFRC's F-15B #836. The PFTF attaches to the centerline pylon of the aircraft and Has an integrated 6 axis force balance for flight testing of propulsion experiments The PTFF has undergone two previous flight validation test phases: (1)The Local Mach Investigation (LMT) flights, in which an air data boom was attached to a cylinder with a conical nose cap . This flight test phase quantified the local Mach number and the local flow angle at a single point under the F-155B/PFTF. (2) The Cone Drag Experiment (CDE), in which the cylinder / nosecap assembly was tested in order to validate the PFTF's integral 6-component force balance. The next test phase with the PFTF is the flight test of the channeled centerbody axisymmetric inlet. However, for the flight data from this test to be valid, more information must be gathered concerning the quality of the flow through the aerodynamic interface plane of the inlet. The flow angularity and Mach number must be known at multiple locations on the interface plane. Flight data will be gathered using a custom-design flowfield rake to probe the flow underneath the F-15B at the design flight conditions.

  12. Alignment Fixtures For Vacuum-Plasma-Spray Gun

    NASA Technical Reports Server (NTRS)

    Woodford, William H.; Mckechnie, Timothy N.; Power, Christopher A.; Daniel, Ronald L., Jr.

    1993-01-01

    Fixtures for alignment of vacuum-plasma-spray guns built. Each fixture designed to fit specific gun and holds small, battery-powered laser on centerline of gun. Laser beam projects small red dot where centerline intersects surface of workpiece to be sprayed. After laser beam positioned on surface of workpiece, fixture removed from gun and spraying proceeds.

  13. Axial alignment fixtures for tension tests of threaded specimens

    NASA Technical Reports Server (NTRS)

    Jones, M. H.; Bubsey, R. T.; Succop, G.; Brown, W. F., Jr.

    1974-01-01

    Description of two axial alignment fixtures that are capable of providing very low load application eccentricity in tension tests of threaded notched cylindrical specimens. The described fixtures are simple in design, very compact, and free from the effects of friction. Also, an evaluation procedure is presented that can be used to qualify any fixture for use in sharp notch tensile tests.

  14. Design and Experimental Performance of a Two Stage Partial Admission Turbine, Task B.1/B.4

    NASA Technical Reports Server (NTRS)

    Sutton, R. F.; Boynton, J. L.; Akian, R. A.; Shea, Dan; Roschak, Edmund; Rojas, Lou; Orr, Linsey; Davis, Linda; King, Brad; Bubel, Bill

    1992-01-01

    A three-inch mean diameter, two-stage turbine with partial admission in each stage was experimentally investigated over a range of admissions and angular orientations of admission arcs. Three configurations were tested in which first stage admission varied from 37.4 percent (10 of 29 passages open, 5 per side) to 6.9 percent (2 open, 1 per side). Corresponding second stage admissions were 45.2 percent (14 of 31 passages open, 7 per side) and 12.9 percent (4 open, 2 per side). Angular positions of the second stage admission arcs with respect to the first stage varied over a range of 70 degrees. Design and off-design efficiency and flow characteristics for the three configurations are presented. The results indicated that peak efficiency and the corresponding isentropic velocity ratio decreased as the arcs of admission were decreased. Both efficiency and flow characteristics were sensitive to the second stage nozzle orientation angles.

  15. 46 CFR 154.406 - Design loads for cargo tanks and fixtures: General.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... loads: (1) Internal pressure head. (2) External pressure load. (3) Dynamic loads resulting from the... cargo transfer. (b) A cargo tank must be designed for the most unfavorable static heel angle within a...

  16. 46 CFR 154.406 - Design loads for cargo tanks and fixtures: General.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... loads: (1) Internal pressure head. (2) External pressure load. (3) Dynamic loads resulting from the... cargo transfer. (b) A cargo tank must be designed for the most unfavorable static heel angle within a...

  17. 46 CFR 154.406 - Design loads for cargo tanks and fixtures: General.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... loads: (1) Internal pressure head. (2) External pressure load. (3) Dynamic loads resulting from the... cargo transfer. (b) A cargo tank must be designed for the most unfavorable static heel angle within a...

  18. 42 CFR 35.7 - Admissions; designation of person to be notified.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 1 2012-10-01 2012-10-01 false Admissions; designation of person to be notified. 35.7 Section 35.7 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICAL CARE AND EXAMINATIONS HOSPITAL AND STATION MANAGEMENT General § 35.7 Admissions; designation...

  19. 42 CFR 35.7 - Admissions; designation of person to be notified.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 1 2013-10-01 2013-10-01 false Admissions; designation of person to be notified. 35.7 Section 35.7 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICAL CARE AND EXAMINATIONS HOSPITAL AND STATION MANAGEMENT General § 35.7 Admissions; designation...

  20. 42 CFR 35.7 - Admissions; designation of person to be notified.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 1 2014-10-01 2014-10-01 false Admissions; designation of person to be notified. 35.7 Section 35.7 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICAL CARE AND EXAMINATIONS HOSPITAL AND STATION MANAGEMENT General § 35.7 Admissions; designation...

  1. Fixture For Calibrating Pressure Probe

    NASA Technical Reports Server (NTRS)

    Ashby, George C., Jr.; Vasquez, Peter; Horsley, Lewis A.; Bowman, John T.; Zumbrun, Henry N.; Eves, John W.

    1994-01-01

    Fixture in form of specially designed clamshell housing enables in situ calibration of pressure transducer mounted in body of pressure probe in wind tunnel. Includes two metal half shells machined with necks and matching cavities, when put together, define larger neck and cavity accommodating probe. Probe secured to bottom half shell by use of clamp before installing top half shell: necessary to follow sequence to protect probe during assembly. Clamshell calibration fixture attached to pressure probe in few minutes, making it possible to calibrate pressure transducer at convenient times. Calibrations performed before and after wind-tunnel runs each day, between runs in event of delays or suspected malfunctions, and essentially any other time, without having to remove probe from wind tunnel.

  2. Propulsion Flight-Test Fixture

    NASA Technical Reports Server (NTRS)

    Palumbo, Nate; Vachon, M. Jake; Richwine, Dave; Moes, Tim; Creech, Gray

    2003-01-01

    NASA Dryden Flight Research Center s new Propulsion Flight Test Fixture (PFTF), designed in house, is an airborne engine-testing facility that enables engineers to gather flight data on small experimental engines. Without the PFTF, it would be necessary to obtain such data from traditional wind tunnels, ground test stands, or laboratory test rigs. Traditionally, flight testing is reserved for the last phase of engine development. Generally, engines that embody new propulsion concepts are not put into flight environments until their designs are mature: in such cases, either vehicles are designed around the engines or else the engines are mounted in or on missiles. However, a captive carry capability of the PFTF makes it possible to test engines that feature air-breathing designs (for example, designs based on the rocket-based combined cycle) economically in subscale experiments. The discovery of unknowns made evident through flight tests provides valuable information to engine designers early in development, before key design decisions are made, thereby potentially affording large benefits in the long term. This is especially true in the transonic region of flight (from mach 0.9 to around 1.2), where it can be difficult to obtain data from wind tunnels and computational fluid dynamics. In January 2002, flight-envelope expansion to verify the design and capabilities of the PFTF was completed. The PFTF was flown on a specially equipped supersonic F-15B research testbed airplane, mounted on the airplane at a center-line attachment fixture, as shown in Figure 1. NASA s F-15B testbed has been used for several years as a flight-research platform. Equipped with extensive research air-data, video, and other instrumentation systems, the airplane carries externally mounted test articles. Traditionally, the majority of test articles flown have been mounted at the centerline tank-attachment fixture, which is a hard-point (essentially, a standardized weapon-mounting fixture

  3. Fixture for winding transformers

    NASA Technical Reports Server (NTRS)

    Mclyman, M. T.

    1980-01-01

    Bench-mounted fixture assists operator in winding toroid-shaped transformer cores. Toroid is rigidly held in place as wires are looped around. Arrangement frees both hands for rapid winding and untangling of wires that occurs when core is hand held.

  4. Multiple direction vibration fixture

    DOEpatents

    Cericola, Fred; Doggett, James W.; Ernest, Terry L.; Priddy, Tommy G.

    1991-01-01

    An apparatus for simulating a rocket launch environment on a test item undergoing centrifuge testing by subjecting the item simultaneously or separately to vibration along an axis of centripetal force and along an axis perpendicular to the centripetal force axis. The apparatus includes a shaker motor supported by centrifuge arms and a right angle fixture pivotally connected to one of the shaker motor mounts. When the shaker motor vibrates along the centripetal force axis, the vibrations are imparted to a first side of the right angle fixture. The vibrations are transmitted 90 degrees around the pivot and are directed to a second side of the right angle fixture which imparts vibrations perpendicular to the centripetal force axis. The test item is in contact with a third side of the right angle fixture and receives both centripetal-force-axis vibrations and perpendicular axis vibrations simultaneously. A test item can be attached to the third side near the flexible coupling or near the air bag to obtain vibrations along the centripetal force axis or transverse to the centripetal force axis.

  5. Tape reading fixture

    NASA Technical Reports Server (NTRS)

    1969-01-01

    Commercially available roller type desk pad provides an efficient and orderly manner of handling rolled paper tapes for proofreading. The fixture, which is modified to accept Flex-O-Writer or similar tapes and roll them in either direction, reduces the chance of damaging or soiling the tapes through repeated handling.

  6. 10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... metallic vapors. Metal halide lamp fixture means a light fixture for general lighting application designed... providing any standby or active mode function. PLC control signal means a power line carrier (PLC)...

  7. 10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... metallic vapors. Metal halide lamp fixture means a light fixture for general lighting application designed... providing any standby or active mode function. PLC control signal means a power line carrier (PLC)...

  8. 10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... fixture means a light fixture for general lighting application designed to be operated with a metal halide... function. PLC control signal means a power line carrier (PLC) signal that is supplied to the ballast...

  9. 10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... metallic vapors. Metal halide lamp fixture means a light fixture for general lighting application designed... providing any standby or active mode function. PLC control signal means a power line carrier (PLC)...

  10. CAN HANDLING FIXTURES

    DOEpatents

    Kelman, Ler.R.; Yaggee, F.L.

    1958-08-01

    A sleeveless cauning apparatus is described for bonding and canning uranium fuel elements under the surface of a liquid bonding alloy. The can is supported on a pedestal by vertical pegs, and an adjustable collar is placed around the upper, open end of the can, which preferably is flared to assure accurate centering in the fixture and to guide the uranium slug into the can. The fixture with a can in place is then immersed in a liquid aluminum-silicon alloy and the can becomes filled with the liquid alloy. The slug is inserted by a slug guide located vertically above the can opening. The slug settles by gravity into the can, after which a cap is emplaced. A quenching tool lifts the capped can out of the bath by means of a slot provided for it in the pedestal. This apparatus provides a simple means of canning the slug without danger of injury to the uranium metal or the aluminum can.

  11. Spacecraft utensil/hand cleansing fixture

    NASA Technical Reports Server (NTRS)

    Jonkoniec, T. G.

    1978-01-01

    A fixture which provides a means for a crewman to perform, in zero gravity, laboratory utensil/tool cleansing and personal hygiene functions such as handwashing, shaving, body wash, and teeth brushing is described. A prototype unit developed incorporating design improvements resulting from breadboard tests in a one gravity and zero gravity environment demonstrated the capability of performing the different cleansing functions.

  12. 46 CFR 183.410 - Lighting fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... fixture in an electrical system operating at more than 50 volts must comply with the requirements of UL...) ELECTRICAL INSTALLATION Lighting Systems § 183.410 Lighting fixtures. (a) Each lighting fixture globe,...

  13. Early Bone Formation around Immediately Loaded Transitional Implants Inserted in the Human Posterior Maxilla: The Effects of Fixture Design and Surface

    PubMed Central

    Pires, Jefferson Trabach; Luongo, Giuseppe; Piattelli, Adriano

    2017-01-01

    Aim. To evaluate the effects of fixture design and surface on the early bone formation around immediately loaded implants inserted in the human posterior maxilla. Materials and Methods. Ten totally edentulous subjects received two transitional implants: one tapered implant with knife-edge threads/nanostructured calcium-incorporated surface (test: Anyridge®, Megagen, Gyeongbuk, South Korea) and one cylindrical implant with self-tapping threads/sandblasted surface (control: EZPlus®, Megagen). The implants were placed according to a split-mouth design and immediately loaded to support an interim complete denture; after 8 weeks, they were removed for histologic/histomorphometric analysis. The bone-to-implant contact (BIC%) and the bone density (BD%) were calculated. The Wilcoxon test was used to evaluate the differences. Results. With test implants, a mean BIC% and BD% of 35.9 (±9.1) and 31.8 (±7.5) were found. With control implants, a mean BIC% and BD% of 29.9 (±7.6) and 32.5 (±3.9) were found. The mean BIC% was higher with test implants, but this difference was not significant (p = 0.16). Similar BD% were found in the two groups (p = 0.9). Conclusions. In the posterior maxilla, under immediate loading conditions, implants with a knife-edge thread design/nanostructured calcium-incorporated surface seem to increase the peri-implant endosseous healing properties, when compared to implants with self-tapping thread design/sandblasted surface. PMID:28280731

  14. Controlled shear/tension fixture

    DOEpatents

    Hsueh, Chun-Hway [Knoxville, TN; Liu, Chain-tsuan [Knoxville, TN; George, Easo P [Knoxville, TN

    2012-07-24

    A test fixture for simultaneously testing two material test samples is provided. The fixture provides substantially equal shear and tensile stresses in each test specimens. By gradually applying a load force to the fixture only one of the two specimens fractures. Upon fracture of the one specimen, the fixture and the load train lose contact and the second specimen is preserved in a state of upset just prior to fracture. Particular advantages of the fixture are (1) to control the tensile to shear load on the specimen for understanding the effect of these stresses on the deformation behavior of advanced materials, (2) to control the location of fracture for accessing localized material properties including the variation of the mechanical properties and residual stresses across the thickness of advanced materials, (3) to yield a fractured specimen for strength measurement and an unfractured specimen for examining the microstructure just prior to fracture.

  15. Fixture For Crush Testing Of Composite Plates

    NASA Technical Reports Server (NTRS)

    Jackson, Karen E.; Lavoie, J. Andre; Morton, John

    1995-01-01

    Test fixture holds composite-material (matrix/fiber) plate specimens for crush testing in universal compression-testing machine to determine energy absorption characteristics of composite material system and laminate. Accommodates specimens of two different sizes; 6 by 4 by 0.16 in. and 3 by 2 by 0.08 in., designated as full scale and half scale, respectively. Contributes to development of more crashworthy composite-material structural components of aircraft.

  16. 46 CFR 183.410 - Lighting fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 7 2013-10-01 2013-10-01 false Lighting fixtures. 183.410 Section 183.410 Shipping...) ELECTRICAL INSTALLATION Lighting Systems § 183.410 Lighting fixtures. (a) Each lighting fixture globe, lens..., radio room, galley, or similar space where it is not subject to damage. (b) A lighting fixture may...

  17. 46 CFR 183.410 - Lighting fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 7 2014-10-01 2014-10-01 false Lighting fixtures. 183.410 Section 183.410 Shipping...) ELECTRICAL INSTALLATION Lighting Systems § 183.410 Lighting fixtures. (a) Each lighting fixture globe, lens..., radio room, galley, or similar space where it is not subject to damage. (b) A lighting fixture may...

  18. 46 CFR 183.410 - Lighting fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 7 2011-10-01 2011-10-01 false Lighting fixtures. 183.410 Section 183.410 Shipping...) ELECTRICAL INSTALLATION Lighting Systems § 183.410 Lighting fixtures. (a) Each lighting fixture globe, lens..., radio room, galley, or similar space where it is not subject to damage. (b) A lighting fixture may...

  19. 46 CFR 183.410 - Lighting fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Lighting fixtures. 183.410 Section 183.410 Shipping...) ELECTRICAL INSTALLATION Lighting Systems § 183.410 Lighting fixtures. (a) Each lighting fixture globe, lens..., radio room, galley, or similar space where it is not subject to damage. (b) A lighting fixture may...

  20. Fixture for aligning motor assembly

    SciTech Connect

    Shervington, Roger M.; Vaghani, Vallabh V.; Vanek, Laurence D.; Christensen, Scott A.

    2009-12-08

    An alignment fixture includes a rotor fixture, a stator fixture and a sensor system which measures a rotational displacement therebetween. The fixture precisely measures rotation of a generator stator assembly away from a NULL position referenced by a unique reference spline on the rotor shaft. By providing an adjustable location of the stator assembly within the housing, the magnetic axes within each generator shall be aligned to a predetermined and controlled tolerance between the generator interface mounting pin and the reference spline on the rotor shaft. Once magnetically aligned, each generator is essentially a line replaceable unit which may be readily mounted to any input of a multi-generator gearbox assembly with the assurance that the magnetic alignment will be within a predetermined tolerance.

  1. Resistance-Welding Test Fixture

    NASA Technical Reports Server (NTRS)

    Brennan, Andrew D.

    1990-01-01

    Realistic welding conditions produce reliable specimens. Simple fixture holds resistance-welding test specimens. Specimen holder includes metallic holder and clamps to provide electrical and thermal paths and plastic parts providing thermal and electrical isolation.

  2. Design and application of a quasistatic crush test fixture for investigating scale effects in energy absorbing composite plates. M.S. Thesis

    NASA Technical Reports Server (NTRS)

    Lavoie, J. Andre; Morton, John

    1993-01-01

    A crush test fixture for measuring energy absorption of flat plate specimens from an earlier study was redesigned to eliminate the problem of binding of the load transfer platen with the guide posts. Further modifications were to increase the stroke, and combine the two scaled text fixtures into one. This new crush text fixture was shown to produce load-displacement histories exhibiting well developed sustained crushing loads over long strokes. An experimental study was conducted on two material systems: AS4/3502 graphite/epoxy, and a hybrid AS4-Kevlar/3502 composite. The effect of geometric scaling of specimen size, the effect of ply level and sublaminate-level scaling of the stacking sequence of the full scale specimens, and the effect of trigger mechanism on the energy absorption capability were investigated. The new crush test fixture and flat plate specimens produced peak and sustained crushing loads that were lower than obtained with the old crush text fixture. The trigger mechanism used influenced the specific sustained crushing stress (SSCS). The results indicated that to avoid any reduction in the SSCS when scaling from the 1/2 scale to full scale specimen size, the sublaminate-level scaling approach should be used, in agreement with experiments on tubes. The use of Kevlar in place of the graphite 45 deg plies was not as effective a means for supporting and containing the 0 deg graphite plies for rushing of flat plates and resulted in a drop in the SSCS. This result did not correlate with that obtained for tubes.

  3. Graphite Composite Panel Polishing Fixture

    NASA Technical Reports Server (NTRS)

    Hagopian, John; Strojny, Carl; Budinoff, Jason

    2011-01-01

    The use of high-strength, lightweight composites for the fixture is the novel feature of this innovation. The main advantage is the light weight and high stiffness-to-mass ratio relative to aluminum. Meter-class optics require support during the grinding/polishing process with large tools. The use of aluminum as a polishing fixture is standard, with pitch providing a compliant layer to allow support without deformation. Unfortunately, with meter-scale optics, a meter-scale fixture weighs over 120 lb (.55 kg) and may distort the optics being fabricated by loading the mirror and/or tool used in fabrication. The use of composite structures that are lightweight yet stiff allows standard techniques to be used while providing for a decrease in fixture weight by almost 70 percent. Mounts classically used to support large mirrors during fabrication are especially heavy and difficult to handle. The mount must be especially stiff to avoid deformation during the optical fabrication process, where a very large and heavy lap often can distort the mount and optic being fabricated. If the optic is placed on top of the lapping tool, the weight of the optic and the fixture can distort the lap. Fixtures to support the mirror during fabrication are often very large plates of aluminum, often 2 in. (.5 cm) or more in thickness and weight upwards of 150 lb (68 kg). With the addition of a backing material such as pitch and the mirror itself, the assembly can often weigh over 250 lb (.113 kg) for a meter-class optic. This innovation is the use of a lightweight graphite panel with an aluminum honeycomb core for use as the polishing fixture. These materials have been used in the aerospace industry as structural members due to their light weight and high stiffness. The grinding polishing fixture consists of the graphite composite panel, fittings, and fixtures to allow interface to the polishing machine, and introduction of pitch buttons to support the optic under fabrication. In its

  4. Pyroshock simulation for satellite components using a tunable resonant fixture

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1992-12-31

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (<8 inch cube) satellite and weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it`s response retched the environment A new test method has been developed which eliminates the need to have a different resonant fixture for each test requirement This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture`s response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch {times} 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  5. Novel Adaptive Fixturing for Thin Walled Aerospace Parts

    NASA Astrophysics Data System (ADS)

    Merlo, Angelo; Ricciardi, Donato; Salvi, Edoardo; Fantinati, Dario; Iorio, Ernesto

    2011-12-01

    In the aerospace industry the monolithic structures have been introduced to reduce the costs of assembling large numbers of components. The expected benefit of using thin walled monolithic parts is given by a large reduction in the overall manufacturing costs, nevertheless this kind of component encounters a critical phase in fixturing. Fixtures are used to locate and hold workpieces during manufacturing. Because workpiece surface errors and fixture set-up errors (called source errors) always exist, the fixtured workpiece will consequently have position and/or orientation errors (called resultant errors) that will definitely affect the final machining accuracy. Most often the current clamping procedure is not straightforward, it implies several steps and the success of the operation hardly depends by the skill of the human operator. It is estimated that fixturing could constitute 10-20% of the total manufacturing costs, assuming that the fixtures are amortized over relatively small batches. Fixturing devices must satisfy two requisites, which, in some terms, are opposite: to provide relatively high forces in order to guarantee that the workpiece will be maintained in position under the maximum cutting forces to reduce as much as possible strains induced in the workpiece. Limiting the strains induced in the workpiece is crucial because of elastic strain recovery: releasing the clamped workpiece would result in an unwanted final deformation. In this paper a novel adaptive fixturing based on active clamping forces (supplied by piezoelectric actuators) is presented: a real aerospace part case study, - a Nozzle Guide Vane (NGV) -, is introduced, the related problems are identified, and the adopted solutions shown. The proposed adaptive fixturing device can lead to the following advantages: to perform an automatic errors-free workpiece clamping and then drastically reduce the overall fixturing set up time; to recover unwanted strains induced to the workpiece, in order to

  6. Measuring alignment of loading fixture

    DOEpatents

    Scavone, Donald W.

    1989-01-01

    An apparatus and method for measuring the alignment of a clevis and pin type loading fixture for compact tension specimens include a pair of substantially identical flat loading ligaments. Each loading ligament has two apertures for the reception of a respective pin of the loading fixture and a thickness less than one-half of a width of the clevis opening. The pair of loading ligaments are mounted in the clevis openings at respective sides thereof. The loading ligaments are then loaded by the pins of the loading fixture and the strain in each loading ligament is measured. By comparing the relative strain of each loading ligament, the alignment of the loading fixture is determined. Preferably, a suitable strain gage device is located at each longitudinal edge of a respective loading ligament equidistant from the two apertures in order to determine the strain thereat and hence the strain of each ligament. The loading ligaments are made substantially identical by jig grinding the loading ligaments as a matched set. Each loading ligament can also be individually calibrated prior to the measurement.

  7. Fixture for assembling solar panels

    NASA Technical Reports Server (NTRS)

    Dillard, P. A.; Fritz, W. M.

    1979-01-01

    Vacuum fixture attaches array of silicon solar cells to mounting plate made of clear glass which holds and protects cells. Glass plate transmits, rather than absorbs, solar energy thus cooling cells for efficient operation. Device therefore reduces handling of cells and interconnecting conductors to one operation.

  8. 46 CFR 120.410 - Lighting fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lighting fixtures. 120.410 Section 120.410 Shipping... PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Lighting Systems § 120.410 Lighting fixtures. (a) Each lighting fixture globe, lens, or diffuser must have a...

  9. 46 CFR 120.410 - Lighting fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Lighting fixtures. 120.410 Section 120.410 Shipping... PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Lighting Systems § 120.410 Lighting fixtures. (a) Each lighting fixture globe, lens, or diffuser must have a...

  10. 46 CFR 120.410 - Lighting fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Lighting fixtures. 120.410 Section 120.410 Shipping... PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Lighting Systems § 120.410 Lighting fixtures. (a) Each lighting fixture globe, lens, or diffuser must have a...

  11. 46 CFR 129.410 - Lighting fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Lighting fixtures. 129.410 Section 129.410 Shipping... INSTALLATIONS Lighting Systems § 129.410 Lighting fixtures. (a) Each globe, lens, or diffuser of a lighting... lighting fixture may be used as a connection box for a circuit other than the branch circuit supplying...

  12. 46 CFR 120.410 - Lighting fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Lighting fixtures. 120.410 Section 120.410 Shipping... PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Lighting Systems § 120.410 Lighting fixtures. (a) Each lighting fixture globe, lens, or diffuser must have a...

  13. 46 CFR 129.410 - Lighting fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lighting fixtures. 129.410 Section 129.410 Shipping... INSTALLATIONS Lighting Systems § 129.410 Lighting fixtures. (a) Each globe, lens, or diffuser of a lighting... lighting fixture may be used as a connection box for a circuit other than the branch circuit supplying...

  14. 46 CFR 129.410 - Lighting fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Lighting fixtures. 129.410 Section 129.410 Shipping... INSTALLATIONS Lighting Systems § 129.410 Lighting fixtures. (a) Each globe, lens, or diffuser of a lighting... lighting fixture may be used as a connection box for a circuit other than the branch circuit supplying...

  15. 46 CFR 120.410 - Lighting fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Lighting fixtures. 120.410 Section 120.410 Shipping... PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Lighting Systems § 120.410 Lighting fixtures. (a) Each lighting fixture globe, lens, or diffuser must have a...

  16. 46 CFR 129.410 - Lighting fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Lighting fixtures. 129.410 Section 129.410 Shipping... INSTALLATIONS Lighting Systems § 129.410 Lighting fixtures. (a) Each globe, lens, or diffuser of a lighting... lighting fixture may be used as a connection box for a circuit other than the branch circuit supplying...

  17. 46 CFR 129.410 - Lighting fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Lighting fixtures. 129.410 Section 129.410 Shipping... INSTALLATIONS Lighting Systems § 129.410 Lighting fixtures. (a) Each globe, lens, or diffuser of a lighting... lighting fixture may be used as a connection box for a circuit other than the branch circuit supplying...

  18. Pyroshock simulation for satellite components using a tunable resonant fixture

    NASA Astrophysics Data System (ADS)

    Davie, N. T.; Bateman, V. I.

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (less than 8 inch cube) satellite and weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it's response reached the environment. A new test method has been developed which eliminates the need to have a different resonant fixture for each test requirement. This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture's response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch x 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  19. Pyroshock simulation for satellite components using a tunable resonant fixture

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1992-01-01

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (<8 inch cube) satellite and weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it's response retched the environment A new test method has been developed which eliminates the need to have a different resonant fixture for each test requirement This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture's response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch [times] 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  20. Development of an improved GTA (gas tungsten arc) weld temperature monitor fixture

    SciTech Connect

    Hollar, D.L.

    1990-05-01

    An initial design weld temperature control fixture was implemented into final closure of an electronic assembly in November 1986. Use of this fixture indicated several areas that could be improved. Review of these areas with the process engineer and the weld operator provided the ideas to be incorporated into the new design Phase 2 fixture. Some primary areas of change and improvement included fixture mobility to provide better accessibility to the weld joint area, automatic timed blow cooling of the weld joint, and a feature to assure proper thermocouple placement. The resulting Phase 2 fixture design provided all of the essential weld temperature monitoring features in addition to several significant improvements. Technology developed during this project will pave the way to similar process monitoring of other manual gas tungsten arc (GTA) welding applications. 9 figs.

  1. Natural-convection heat transfer of a spherical lighting fixture

    SciTech Connect

    Ikeda, Takamasa; Fujii, Tetsu

    1994-09-01

    The surface temperatures of the inner lamp and the outer globe of a spherical lighting fixture, the surfaces of which are painted black, were measured. From the results, the average convective heat-transfer coefficients between the inner lamp and the outer globe and on the outer surface of the globe were obtained. These data are correlated with the aid of existing equations for two concentric spheres and the outer surface of a single sphere. The relationships between the maximum and mean temperatures on the lamp and the globe were also obtained. By the use of these equations, a method for the optimal thermal design of spherical lighting fixtures is proposed.

  2. Optical fiber cable chemical stripping fixture

    NASA Technical Reports Server (NTRS)

    Kolasinski, John R. (Inventor); Coleman, Alexander M. (Inventor)

    1995-01-01

    An elongated fixture handle member is connected to a fixture body member with both members having interconnecting longitudinal central axial bores for the passage of an optical cable therethrough. The axial bore of the fixture body member, however, terminates in a shoulder stop for the outer end of a jacket of the optical cable covering both an optical fiber and a coating therefor, with an axial bore of reduced diameter continuing from the shoulder stop forward for a predetermined desired length to the outer end of the fixture body member. A subsequent insertion of the fixture body member including the above optical fiber elements into a chemical stripping solution results in a softening of the exposed external coating thereat which permits easy removal thereof from the optical fiber while leaving a desired length coated fiber intact within the fixture body member.

  3. Modification of Fixture Mount to be Used as an Impression Coping in Closely Placed Implants.

    PubMed

    Mahoorkar, Sudhindra; Jain, Anoop; K, Cauvery; Kumar, Pawan; Havale, Raghavendra

    2014-04-01

    An implant-level impression is often desired for designing and fabricating an implant-supported fixed restoration. This clinical report describes the use of modified press-fit metal implant fixture mount as an impression coping for making an impression of closely placed implants. The fixture mount is easier to manipulate, time saving and more comfortable for both the clinician and patient because the implant fixture mount is connected to the implant by pressing on instead of screwing. As compared to plastic press fit impression coping, metal fixture mount will not distort when modification of fixture mount are required in convergently or closely placed implants. It has the advantage of both the open-tray and closed-tray implant impression techniques.

  4. Osseointegrated fixture placement with simultaneous tooth extraction.

    PubMed

    Schabes, G A; Sacks, H G; Kaufman, P S

    1992-03-01

    Three cases are presented that illustrate the potential for accelerating the healing phase with fixture-based treatment. Depending on the clinical circumstances, techniques may include radical alveolectomy, the use of fresh extraction sockets, and fixture placement in inter-radicular bone.

  5. 24 CFR 3280.607 - Plumbing fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Plumbing Systems § 3280.607 Plumbing fixtures..., dishwashing, or other force-discharge fixture or appliance. (See also § 3280.607(b)(4)(ii).) (6) Water... spacing as to be reasonably accessible for their intended use. (2) Water closets. (i) Water closets...

  6. Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

    SciTech Connect

    List, III, Frederick Alyious; Feuerstein, Albert; Dehoff, Ryan; Kirka, Michael; Carver, Keith

    2016-03-30

    The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheet material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture

  7. Fixture for holding testing transducer

    DOEpatents

    Wagner, T.A.; Engel, H.P.

    A fixture for mounting an ultrasonic transducer against the end of a threaded bolt or stud to test the same for flaws. A base means threadedly secured to the side of the bolt has a rotating ring thereon. A post rising up from the ring (parallel to the axis of the workpiece) pivotally mounts a variable length cross arm, on the inner end of which is mounted the transducer. A spring means acts between the cross arm and the base to apply the testing transducer against the workpiece at a constant pressure. The device maintains constant for successive tests the radial and circumferential positions of the testing transducer and its contact pressure against the end of the workpiece.

  8. Fixture for holding testing transducer

    DOEpatents

    Wagner, Thomas A.; Engel, Herbert P.

    1984-01-01

    A fixture for mounting an ultrasonic transducer against the end of a threaded bolt or stud to test the same for flaws. A base means threadedly secured to the side of the bolt has a rotating ring thereon. A post rising up from the ring (parallel to the axis of the workpiece) pivotally mounts a variable length cross arm, on the inner end of which is mounted the transducer. A spring means acts between the cross arm and the base to apply the testing transducer against the workpiece at a constant pressure. The device maintains constant for successive tests the radial and circumferential positions of the testing transducer and its contact pressure against the end of the workpiece.

  9. Shocking Admission

    ERIC Educational Resources Information Center

    Hoover, Eric; Millman, Sierra

    2007-01-01

    Marilee Jones's career had been a remarkable success. She joined Massachusetts Institute of Technology's (MIT's) admissions office in 1979, landing a job in Cambridge at a time when boys ruled the sandbox of the admissions profession. Her job was to help MIT recruit more women, who then made up less than one-fifth of the institute's students. She…

  10. Spacecraft utensil/hand cleansing fixture. [for space shuttles

    NASA Technical Reports Server (NTRS)

    Rosener, A. A.; Jonkoniec, T. G.; Wilson, D. A.; Schulz, J. R.

    1975-01-01

    A system concept for an inflight utensil/hand cleansing fixture is described which includes the following features: (1) capability for efficient cleansing and rinsing of utensils or hands, and (2) provision for general waste fluid disposal. The design concept provides for the capability of functioning for a 30 day shuttle mission containing seven occupants/users. The long range goal is to provide a functioning system capable of operating for missions of at least 120 days. The fixture is a self-contained unit that can be installed in the standard water interface requirements. Service to the unit is a single source of unheated potable water and water is discharged from the unit into a single return waste connection. In addition, the design includes provisions for the intake and discharge of purge air and the discharge of evolved gases. Both the air and the gases are filtered or processed in the assembly before releasing them into the habitability area.

  11. Universal test fixture for monolithic mm-wave integrated circuits calibrated with an augmented TRD algorithm

    NASA Technical Reports Server (NTRS)

    Romanofsky, Robert R.; Shalkhauser, Kurt A.

    1989-01-01

    The design and evaluation of a novel fixturing technique for characterizing millimeter wave solid state devices is presented. The technique utilizes a cosine-tapered ridge guide fixture and a one-tier de-embedding procedure to produce accurate and repeatable device level data. Advanced features of this technique include nondestructive testing, full waveguide bandwidth operation, universality of application, and rapid, yet repeatable, chip-level characterization. In addition, only one set of calibration standards is required regardless of the device geometry.

  12. Holding fixture for variable-contour parts

    NASA Technical Reports Server (NTRS)

    Haynie, C. C.; Packer, P. N.; Zebus, P. P.

    1979-01-01

    Array of vacuum cups on spindles holds parts for safe machining and other processings. Variable-contour part resting on fixture is held firmly enough for machining, coating, or other mechanical treatment.

  13. Fixture for forming evaporative pattern (EPC) process patterns

    DOEpatents

    Turner, Paul C.; Jordan, Ronald R.; Hansen, Jeffrey S.

    1993-01-01

    A method of casting metal using evaporative pattern casting process patterns in combination with a fixture for creating and maintaining a desired configuration in flexible patterns. A pattern is constructed and gently bent to the curvature of a suitable fixture. String or thin wire, which burns off during casting, is used to tie the pattern to the fixture. The fixture with pattern is dipped in a commercially available refractory wash to prevent metal adherence and sticking to the fixture. When the refractory wash is dry, the fixture and pattern are placed in a flask, and sand is added and compacted by vibration. The pattern remains in position, restrained by the fixture. Metal that is poured directly into the pattern replaces the pattern exactly but does not contact or weld to the fixture due to the protective refractory layer. When solid, the casting is easily separated from the fixture. The fixture can be cleaned for reuse in conventional casting cleaning equipment.

  14. Combined Loads Test Fixture for Thermal-Structural Testing Aerospace Vehicle Panel Concepts

    NASA Technical Reports Server (NTRS)

    Fields, Roger A.; Richards, W. Lance; DeAngelis, Michael V.

    2004-01-01

    A structural test requirement of the National Aero-Space Plane (NASP) program has resulted in the design, fabrication, and implementation of a combined loads test fixture. Principal requirements for the fixture are testing a 4- by 4-ft hat-stiffened panel with combined axial (either tension or compression) and shear load at temperatures ranging from room temperature to 915 F, keeping the test panel stresses caused by the mechanical loads uniform, and thermal stresses caused by non-uniform panel temperatures minimized. The panel represents the side fuselage skin of an experimental aerospace vehicle, and was produced for the NASP program. A comprehensive mechanical loads test program using the new test fixture has been conducted on this panel from room temperature to 500 F. Measured data have been compared with finite-element analyses predictions, verifying that uniform load distributions were achieved by the fixture. The overall correlation of test data with analysis is excellent. The panel stress distributions and temperature distributions are very uniform and fulfill program requirements. This report provides details of an analytical and experimental validation of the combined loads test fixture. Because of its simple design, this unique test fixture can accommodate panels from a variety of aerospace vehicle designs.

  15. A method for accounting for test fixture compliance when estimating proximal femur stiffness.

    PubMed

    Rossman, Timothy; Dragomir-Daescu, Dan

    2016-09-06

    Fracture testing of cadaveric femora to obtain strength and stiffness information is an active area of research in developing tools for diagnostic prediction of bone strength. These measurements are often used in the estimation and validation of companion finite element models constructed from the femora CT scan data, therefore, the accuracy of the data is of paramount importance. However, experimental stiffness calculated from force-displacement data has largely been ignored by most researchers due to inherent error in the differential displacement measurement obtained when not accounting for testing apparatus compliance. However, having such information is necessary for validation of computational models. Even in the few cases when fixture compliance was considered the measurements showed large lab-to-lab variation due to lack of standardization in fixture design. We examined the compliance of our in-house designed cadaveric femur test fixture to determine the errors we could expect when calculating stiffness from the collected experimental force-displacement data and determined the stiffness of the test fixture to be more than 10 times the stiffness of the stiffest femur in a sample of 44 femora. When correcting the apparent femur stiffness derived from the original data, we found that the largest stiffness was underestimated by about 10%. The study confirmed that considering test fixture compliance is a necessary step in improving the accuracy of fracture test data for characterizing femur stiffness, and highlighted the need for test fixture design standardization for proximal femur fracture testing.

  16. Pyroshock simulation for satellite components using a tunable resonant fixture, Phase 1

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1992-10-01

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (<8 inch cube) weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it`s response matched the environment. A new test method has been developed which eliminates the need to have a different resonant fixture for each test requirement. This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture`s response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch {times} 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  17. Mitigation of self-excited oscillations at full load: CFD analysis of air admission and effects of runner design

    NASA Astrophysics Data System (ADS)

    Chirkov, D.; Scherbakov, P.; Cherny, S.; Zakharov, A.; Skorospelov, V.; Turuk, P.

    2016-11-01

    In full and over load operating points some Francis turbines experience strong selfexcited pressure and power oscillations, which restrict the range of operation and maximum output of the turbine. Previously the authors proposed a 1D-3D two-phase model and numerical method for investigation of this phenomenon. In the present paper this model is further extended and applied to investigation of countermeasures, used for prevention of high load oscillations. First, the third phase - non-condensable air - is introduced into the model in order to investigate the effect of air admission. Then, several modifications of runner cone are examined, showing negligible effect on the amplitude and frequency of full load oscillations. Next, different modifications of runner blade shape are considered, giving different axial and circumferential velocity profiles downstream the runner. It is shown that variation of blade shape significantly affects the onset and intensity of self-excited oscillations. The obtained results indicate that proper runner design is able to eliminate high load instability without the need of air admission and reduction in turbine efficiency.

  18. Reflector system for a lighting fixture

    DOEpatents

    Siminovitch, M.J.; Page, E.; Gould, C.T.

    1998-09-08

    Disclosed herein is a reflector system for a lighting fixture having a illumination source surrounded by an envelope. The reflector system includes a first reflector surrounding the illumination source. The reflector system also includes a second reflector which is non-contiguous with the first reflector and which surrounds the illumination source. The illumination source creates light rays which are reflected by the first and second reflectors. The first reflector directs light rays toward the center line of the fixture. However, the reflected rays despite being so reflected do not substantially intersect the envelope. The reflected light rays from the second reflector being directed so that they diverge from the center line of the fixture avoiding intersection with the semi-transparent envelope. 5 figs.

  19. Reflector system for a lighting fixture

    DOEpatents

    Siminovitch, Michael J.; Page, Erik; Gould, Carl T.

    2001-01-01

    Disclosed herein is a reflector system for a lighting fixture having a illumination source surrounded by an envelope. The reflector system includes a first reflector surrounding the illumination source. The reflector system also includes a second reflector which is non-contiguous with the first reflector and which surrounds the illumination source. The illumination source creates light rays which are reflected by the first and second reflectors. The first reflector directs light rays toward the center line of the fixture. However, the reflected rays despite being so reflected do not substantially intersect the envelope. The reflected light rays from the second reflector being directed so that they diverge from the center line of the fixture avoiding intersection with the semi-transparent envelope.

  20. Reflector system for a lighting fixture

    DOEpatents

    Siminovitch, Michael J.; Page, Erik; Gould, Carl T.

    1998-01-01

    Disclosed herein is a reflector system for a lighting fixture having a illumination source surrounded by an envelope. The reflector system includes a first reflector surrounding the illumination source. The reflector system also includes a second reflector which is non-contiguous with the first reflector and which surrounds the illumination source. The illumination source creates light rays which are reflected by the first and second reflectors. The first reflector directs light rays toward the center line of the fixture. However, the reflected rays despite being so reflected do not substantially intersect the envelope. The reflected light rays from the second reflector being directed so that they diverge from the center line of the fixture avoiding intersection with the semi-transparent envelope.

  1. Thermal resilient multiple jaw braze fixture

    DOEpatents

    Ney, Robert; Perrone, Alex J.

    1995-07-11

    A braze fixture has side walls forming a cavity with an opening to receive a stack of parts to be brazed. Sidewalls of the housing have a plurality of bearing receiving openings into which bearing rods or jaws are inserted to align the stacked elements of the workpiece. The housing can also have view ports to allow a visual check of the alignment. Straps or wires around the fixture are selected to have thermal characteristics similar to the thermal characteristics of the workpiece undergoing brazing. The straps or wires make physical contact with the bearing rods thereby causing bearing rods to maintain the workpiece in proper alignment throughout the entire brazing cycle.

  2. Machine tools and fixtures: A compilation

    NASA Technical Reports Server (NTRS)

    1971-01-01

    As part of NASA's Technology Utilizations Program, a compilation was made of technological developments regarding machine tools, jigs, and fixtures that have been produced, modified, or adapted to meet requirements of the aerospace program. The compilation is divided into three sections that include: (1) a variety of machine tool applications that offer easier and more efficient production techniques; (2) methods, techniques, and hardware that aid in the setup, alignment, and control of machines and machine tools to further quality assurance in finished products: and (3) jigs, fixtures, and adapters that are ancillary to basic machine tools and aid in realizing their greatest potential.

  3. 18. FIRST FLOOR, DETAIL OF CEILING AND LIGHT FIXTURE (AS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. FIRST FLOOR, DETAIL OF CEILING AND LIGHT FIXTURE (AS SEEN IN SC-135-18), MADE OF BRASS, ORIGINALLY GAS, CONVERTED TO ELECTRICITY, FIXTURE LIT - Market Hall, 188 Meeting Street, Charleston, Charleston County, SC

  4. Using Jigs and Fixtures: A Design Brief

    ERIC Educational Resources Information Center

    Dyer, Leon; Stephan, Stuart

    2004-01-01

    The term "tooling" refers to a variety of devices that increase production efficiency in manufacturing. Incorporating the appropriate tooling in the production process generally improves accuracy, speed, and safety. This in turn leads to more profit for the producer and lower prices for the consumer. This article introduces students to two common…

  5. Holding fixture for metallographic mount polishing

    DOEpatents

    Barth, C.H.; Cramer, C.E.

    1997-12-30

    A fixture is described for holding mounted specimens for polishing, having an arm; a body attached to one end of the arm, the body having at least one flange having an opening to accommodate a mounted specimen; and a means applying pressure against the outer surface of the mounted specimen to hold the specimen in contact with the polishing surface. 3 figs.

  6. Holding fixture for metallographic mount polishing

    DOEpatents

    Barth, Clyde H.; Cramer, Charles E.

    1997-01-01

    A fixture for holding mounted specimens for polishing, having an arm; a body attached to one end of the arm, the body having at least one flange having an opening to accommodate a mounted specimen; and a means applying pressure against the outer surface of the mounted specimen to hold the specimen in contact with the polishing surface.

  7. 30 CFR 57.3203 - Rock fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... the ground in an area with similar strata, opening dimensions and ground stresses in any mine; or (2... has similar strata, opening dimensions, and ground stresses as the area where the fixtures are..., and the last bolt installed in each work area during the shift shall be accurately...

  8. 30 CFR 56.3203 - Rock fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... similar strata, opening dimensions and ground stresses in any mine; or (2) Have been tested and shown to... dimensions, and ground stresses as the area where the fixtures are expected to be used. During the test... the rock. (2) The torque of the first bolt, every tenth bolt, and the last bolt installed in each...

  9. Vacuum test fixture improves leakage rate measurements

    NASA Technical Reports Server (NTRS)

    Maier, H.; Marx, H.

    1966-01-01

    Cylindrical chamber, consisting of two matching halves, forms a vacuum test fixture for measuring leakage rates of individual connections, brazed joints, and entrance ports used in closed fluid flow line systems. Once the chamber has been sufficiently evacuated, atmospheric pressure holds the two halves together.

  10. Fixture for mounting small parts for processing

    DOEpatents

    Foreman, Larry R.; Gomez, Veronica M.; Thomas, Michael H.

    1990-01-01

    A fixture for mounting small parts, such as fusion target spheres or microelectronic components. A glass stalk is drawn and truncated near its tip. The truncated end of the glass stalk is dipped into silicone rubber forming an extending streamer. After the rubber cures for approximately 24 hours, a small part is touched to the streamer, and will be held securely throughout processing.

  11. 30 CFR 57.3203 - Rock fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Support-Surface and Underground § 57.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall... grouting material shall not be used. (f) When rock bolts tensioned by torquing are used as a means...

  12. 30 CFR 56.3203 - Rock fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) When rock bolts tensioned by torquing are used as a means of ground support, (1) Selected tension level... § 56.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall— (1) Obtain a...

  13. 30 CFR 56.3203 - Rock fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) When rock bolts tensioned by torquing are used as a means of ground support, (1) Selected tension level... § 56.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall— (1) Obtain a...

  14. 30 CFR 57.3203 - Rock fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Support-Surface and Underground § 57.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall... grouting material shall not be used. (f) When rock bolts tensioned by torquing are used as a means...

  15. 30 CFR 56.3203 - Rock fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) When rock bolts tensioned by torquing are used as a means of ground support, (1) Selected tension level... § 56.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall— (1) Obtain a...

  16. 30 CFR 57.3203 - Rock fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Support-Surface and Underground § 57.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall... grouting material shall not be used. (f) When rock bolts tensioned by torquing are used as a means...

  17. 30 CFR 56.3203 - Rock fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) When rock bolts tensioned by torquing are used as a means of ground support, (1) Selected tension level... § 56.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall— (1) Obtain a...

  18. 30 CFR 57.3203 - Rock fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Support-Surface and Underground § 57.3203 Rock fixtures. (a) For rock bolts and accessories addressed in ASTM F432-95, “Standard Specification for Roof and Rock Bolts and Accessories,” the mine operator shall... grouting material shall not be used. (f) When rock bolts tensioned by torquing are used as a means...

  19. 49 CFR 179.500-13 - Fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.500-13 Fixtures. (a) Attachments, other than those mounted on tank covers or serving as threaded closures for the ends of the...

  20. 49 CFR 179.500-13 - Fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.500-13 Fixtures. (a) Attachments, other than those mounted on tank covers or serving as threaded...

  1. 49 CFR 179.500-13 - Fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.500-13 Fixtures. (a) Attachments, other than those mounted on tank covers or serving as threaded closures for the ends of the...

  2. 49 CFR 179.500-13 - Fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.500-13 Fixtures. (a) Attachments, other than those mounted on tank covers or serving as threaded closures for the ends of the...

  3. 49 CFR 179.500-13 - Fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.500-13 Fixtures. (a) Attachments, other than those mounted on tank covers or serving as threaded closures for the ends of the...

  4. A Mastery Rubric: guiding curriculum design, admissions and development of course objectives.

    PubMed

    Tractenberg, Rochelle E; Umans, Jason G; McCarter, Robert J

    This article describes a 'Mastery Rubric' (MR) used to design both the curriculum and the assessments in a new two-year certificate programme intended to train physicians in clinical research skills. The MR for clinical research skills is built around a set of core research skills: critical review of literature; articulation of research objective; development of research design; development of analysis plan; implementation of the study; implementation of the analysis plan and presentation of results. Four distinct levels of performance are described for each skill: beginning, novice, competent and proficient. This rubric outlines and provides a path to mastery of the clinical research skills the certificate programme was designed and funded to target. Using the rubric to design the curriculum ensures that courses will provide instruction in key domains, promotes assessment that demonstrates development in the target skills and knowledge, and encourages reflection and cognitive self-monitoring in the students. It is a flexible, criterion-referenced definition of 'success' for students as well as the programme itself. The criteria are characterised in terms of the skills, habits of mind and organisational principles that can foster excellence in clinical research, but the approach can be generalised.

  5. A Mastery Rubric: Guiding Curriculum Design, Admissions and Development of Course Objectives

    ERIC Educational Resources Information Center

    Tractenberg, Rochelle E.; Umans, Jason G.; McCarter, Robert J.

    2010-01-01

    This article describes a "Mastery Rubric" (MR) used to design both the curriculum and the assessments in a new two-year certificate programme intended to train physicians in clinical research skills. The MR for clinical research skills is built around a set of core research skills: critical review of literature; articulation of research objective;…

  6. Pyroshock simulation for satellite components using a tunable resonant fixture, Phase 1

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1992-10-01

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (<8 inch cube) weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it's response matched the environment. A new test method has been developed which eliminates the need to have a different resonant fixture for each test requirement. This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture's response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch [times] 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  7. Pyroshock simulation for satellite components using a tunable resonant fixture, phase 1

    NASA Astrophysics Data System (ADS)

    Davie, N. T.; Bateman, V. I.

    1992-10-01

    Aerospace components are often subjected to pyroshock events during flight and deployment and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (less than 8 inch cube) weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it's response matched the environment. A new test method was developed which eliminates the need to have a different resonant fixture for each test requirement. This is accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture's response is done in a simple and deterministic way. This report covers the first phase of this research, which includes design conception through fabrication and evaluation of hardware capable of testing components with up to a 10 inch x 10 inch base. This method will ultimately allow the testing of much larger items, perhaps as large as entire small satellites.

  8. A test fixture for measuring high-temperature hypersonic-engine seal performance

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.

    1990-01-01

    A test fixture for measuring the performance of several high temperature engine seal concepts was installed at the NASA Lewis Research Center. The test fixture was developed to evaluate seal concepts under development for advanced hypersonic engines such as those being considered for the National Aerospace Plane. The fixture can measure static seal leakage performance from room temperature up to 1500 F and air pressure differentials up to 100 psi. Performance of the seals can be measured while sealing against flat or engine simulated distorted walls, where distortions can be as large as 0.150 in. in only an 18 in. span. The fixture is designed to evaluate seals 3 feet long, a typical engine panel length. The seal channel can be configured to test square, circular, or rectangular seals that are nominally 0.5 in. high. The sensitivity of leakage performance to lateral or axial loading can also be measured using specially designed high temperature lateral and axial bellows preload systems. Leakage data for a candidate ceramic wafer engine seal is provided by way of example to demonstrate the test fixture's capabilities.

  9. Thermal resilient multiple jaw braze fixture

    DOEpatents

    Ney, R.; Perrone, A.J.

    1995-07-11

    A braze fixture has side walls forming a cavity with an opening to receive a stack of parts to be brazed. Sidewalls of the housing have a plurality of bearing receiving openings into which bearing rods or jaws are inserted to align the stacked elements of the workpiece. The housing can also have view ports to allow a visual check of the alignment. Straps or wires around the fixture are selected to have thermal characteristics similar to the thermal characteristics of the workpiece undergoing brazing. The straps or wires make physical contact with the bearing rods thereby causing bearing rods to maintain the workpiece in proper alignment throughout the entire brazing cycle. 9 figs.

  10. Development of test fixture for measurement of dielectric properties and its verification using animal tissues.

    PubMed

    Yamamoto, Takahiko; Koshiji, Kohji; Fukuda, Akiko

    2013-09-01

    The electromagnetic compatibility of implantable or wearable medical devices has often been evaluated using human phantoms to electrically mimic biological tissues. However, no currently existing test fixture can measure the electrical characteristics of gel-like materials. In this paper, we report the development of a new test fixture that consists of a coaxial tube whose outer conductor is divided along the axial direction into two sections, which facilitates filling and removal of gel-like materials in order to measure their electrical characteristics. Using this test fixture, we measured the electrical characteristics of a cow's muscular tissues up to 1 h post-mortem; these measurements allowed us to obtain the relative permittivity and conductivity of the biological tissue, which should help to enable the design of new human phantoms.

  11. The Fixture Device of the Horizontal Machining Center for the Input Tray Part Processing

    NASA Astrophysics Data System (ADS)

    Zhou, Ping

    The input tray part is key parts on the production of auto parts of the on the automatic line, this paper mainly studies on the horizontal machining center using the fixture device, the device to ensure the machining accuracy of the input tray part. Through the analysis of the positioning and clamping of the input tray part, design a clamp device, the device is applied in on the horizontal machining center, and on the basis of the fixture add auxiliary support device, in order to improve the input tray part rigidity and stability of processing.

  12. Fixture for mounting small parts for processing

    DOEpatents

    Foreman, L.R.; Gomez, V.M.; Thomas, M.H.

    1990-05-29

    A fixture for mounting small parts, such as fusion target spheres or microelectronic components is disclosed. A glass stalk is drawn and truncated near its tip. The truncated end of the glass stalk is dipped into silicone rubber forming an extending streamer. After the rubber cures for approximately 24 hours, a small part is touched to the streamer, and will be held securely throughout processing. 5 figs.

  13. Pyroshock simulation for satellite components using a tunable resonant fixture - phase 2

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1997-04-01

    Aerospace components are often subjected to pyroshock events during flight and deployment, and must be qualified to this frequently severe environment. Laboratory simulation of pyroshock using a mechanically excited resonant fixture, has gained favor at Sandia for testing small (<8 inch cube) weapon components. With this method, each different shock environment required a different resonant fixture that was designed such that it`s response matched the environment. In Phase 1 (SAND92-2135) of this research, a new test method was developed which eliminated the need to have a different resonant fixture for each test requirement. This was accomplished by means of a tunable resonant fixture that has a response which is adjustable over a wide frequency range. The adjustment of the fixture`s response is done in a simple and deterministic way. This report covers Phase 2 of this research, in which several ideas were explored to extend the Phase 1 results to a larger scale. The test apparatus developed in Phase 1 was capable of testing components with up to a 10 inches x 10 inches base. The goal of the Phase 2 research was to produce an apparatus capable of testing components with up to a 20 inches x 20 inches mounting base. This size capability would allow the testing of most satellite and missile components which frequently consist of large electronic boxes. Several methods to attain this goal were examined, including scaling up the Phase 1 apparatus. Only one of these proved capable of meeting the Phase 2 goals. This report covers all details from concept through fabrication and testing of this Phase 2 apparatus.

  14. Testing Fixture For Microwave Integrated Circuits

    NASA Technical Reports Server (NTRS)

    Romanofsky, Robert; Shalkhauser, Kurt

    1989-01-01

    Testing fixture facilitates radio-frequency characterization of microwave and millimeter-wave integrated circuits. Includes base onto which two cosine-tapered ridge waveguide-to-microstrip transitions fastened. Length and profile of taper determined analytically to provide maximum bandwidth and minimum insertion loss. Each cosine taper provides transformation from high impedance of waveguide to characteristic impedance of microstrip. Used in conjunction with automatic network analyzer to provide user with deembedded scattering parameters of device under test. Operates from 26.5 to 40.0 GHz, but operation extends to much higher frequencies.

  15. Results from a Test Fixture for button BPM Trapped Mode Measurements

    SciTech Connect

    Cameron,P.; Bacha, B.; Blednykh, A.; Pinayev, I.; Singh, O.

    2009-05-04

    A variety of measures have been suggested to mitigate the problem of button BPM trapped mode heating. A test fixture, using a combination of commercial-off-the-shelf and custom machined components, was assembled to validate the simulations. We present details of the fixture design, measurement results, and a comparison of the results with the simulations. A brief history of the trapped mode button heating problem and a set of design rules for BPM button optimization are presented elsewhere in these proceedings. Here we present measurements on a test fixture that was assembled to confirm, if possible, a subset of those rules: (1) Minimize the trapped mode impedance and the resulting power deposited in this mode by the beam. (2) Maximize the power re-radiated back into the beampipe. (3) Maximize electrical conductivity of the outer circumference of the button and minimize conductivity of the inner circumference of the shell, to shift power deposition from the button to the shell. The problem is then how to extract useful and relevant information from S-parameter measurements of the test fixture.

  16. Multisurface fixture permits easy grinding of tool bit angles

    NASA Technical Reports Server (NTRS)

    Jones, C. R.

    1966-01-01

    Multisurface fixture with a tool holder permits accurate grinding and finishing of right and left hand single point threading tools. All angles are ground by changing the fixture position to rest at various references angles without removing the tool from the holder.

  17. 24 CFR 3285.702 - Miscellaneous lights and fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed...

  18. 24 CFR 3285.702 - Miscellaneous lights and fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed...

  19. 24 CFR 3285.702 - Miscellaneous lights and fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed...

  20. 46 CFR 105.30-1 - Electrical fittings and fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Electrical fittings and fixtures. 105.30-1 Section 105... VESSELS COMMERCIAL FISHING VESSELS DISPENSING PETROLEUM PRODUCTS Electrical Requirements § 105.30-1 Electrical fittings and fixtures. (a) In compartments or areas containing tanks or pumps handling other...

  1. 46 CFR 105.30-1 - Electrical fittings and fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Electrical fittings and fixtures. 105.30-1 Section 105... VESSELS COMMERCIAL FISHING VESSELS DISPENSING PETROLEUM PRODUCTS Electrical Requirements § 105.30-1 Electrical fittings and fixtures. (a) In compartments or areas containing tanks or pumps handling other...

  2. 46 CFR 105.30-1 - Electrical fittings and fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Electrical fittings and fixtures. 105.30-1 Section 105... VESSELS COMMERCIAL FISHING VESSELS DISPENSING PETROLEUM PRODUCTS Electrical Requirements § 105.30-1 Electrical fittings and fixtures. (a) In compartments or areas containing tanks or pumps handling other...

  3. 46 CFR 105.30-1 - Electrical fittings and fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Electrical fittings and fixtures. 105.30-1 Section 105... VESSELS COMMERCIAL FISHING VESSELS DISPENSING PETROLEUM PRODUCTS Electrical Requirements § 105.30-1 Electrical fittings and fixtures. (a) In compartments or areas containing tanks or pumps handling other...

  4. 24 CFR 3280.807 - Fixtures and appliances.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically...

  5. 24 CFR 3280.807 - Fixtures and appliances.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically...

  6. 24 CFR 3280.807 - Fixtures and appliances.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically...

  7. 24 CFR 3280.807 - Fixtures and appliances.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically...

  8. 24 CFR 3280.807 - Fixtures and appliances.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. Link to an amendment published at 78 FR 73991, Dec. 9, 2013. (a) Electrical materials, devices, appliances, fittings, and other equipment installed, intended for use in, or attached...

  9. 24 CFR 3285.702 - Miscellaneous lights and fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Miscellaneous lights and fixtures... Equipment § 3285.702 Miscellaneous lights and fixtures. (a) When the home is installed, exterior lighting... canopy and the wiring outlet box. (d) Exterior lights. (1) The junction box covers must be removed...

  10. 16 CFR Figure 1 to Part 1511 - Pacifier Test Fixture

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Pacifier Test Fixture 1 Figure 1 to Part 1511 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR PACIFIERS Pt. 1511, Fig. 1 Figure 1 to Part 1511—Pacifier Test Fixture...

  11. 16 CFR Figure 1 to Part 1511 - Pacifier Test Fixture

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Pacifier Test Fixture 1 Figure 1 to Part 1511 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR PACIFIERS Pt. 1511, Fig. 1 Figure 1 to Part 1511—Pacifier Test Fixture...

  12. 16 CFR Figure 1 to Part 1511 - Pacifier Test Fixture

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Pacifier Test Fixture 1 Figure 1 to Part 1511 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR PACIFIERS Pt. 1511, Fig. 1 Figure 1 to Part 1511—Pacifier Test Fixture...

  13. 16 CFR Figure 1 to Part 1511 - Pacifier Test Fixture

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Pacifier Test Fixture 1 Figure 1 to Part 1511 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR PACIFIERS Pt. 1511, Fig. 1 Figure 1 to Part 1511—Pacifier Test Fixture...

  14. 16 CFR Figure 1 to Part 1511 - Pacifier Test Fixture

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Pacifier Test Fixture 1 Figure 1 to Part 1511 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR PACIFIERS Pt. 1511, Fig. 1 Figure 1 to Part 1511—Pacifier Test Fixture...

  15. IDEFIX: identification of dental fixtures in intraoral x rays

    NASA Astrophysics Data System (ADS)

    Lehmann, Thomas M.; Schmitt, Walter; Horn, Harald; Hillen, Walter

    1996-04-01

    In dental implantology more than one hundred enossal implant systems are in use. Once embedded, the dental x-ray examination is the most important tool for determining implants' producer, name, and type. In this paper, we present a system for automatic detection and identification of dental fixtures in intraoral x rays (IDEFIX) combining common direct digital image acquisition techniques with specially designed image analysis. IDEFIX can process any digital radiograph (e.g. RVG, Sens-A-Ray, Schick, Sidexis, Digora) as well as digitized dental films. A reference database has been generated by precise measurement on the implant systems used so far (eight implants) including parameters like length, diameter, and cross section area. After binarization of the current digital x-ray image, a parameter set is extracted from each detected object applying mathematical morphology. All objects are classified using a simplified nearest neighbor method and the Euclidean distance metric. If the distance of the objects' parameter set to one of the reference sets is below a given threshold, name and type of the identified dental fixture are displayed on the screen. Otherwise, the actual object will be rejected as a no-implant. IDEFIX has been evaluated by processing various in-vitro acquired radiographs. Different implants were classified captured with identical conditions as well as acquired varying the angulation of the x-ray tube. It is shown that misangulations up to twenty degrees are tolerable preserving correct identification. Other image structures like teeth or fillings result in large distances to all reference parameter sets and, therefore, they are reliably recognized as non-implants.

  16. Large angle magnetic suspension test fixture

    NASA Technical Reports Server (NTRS)

    Britcher, Colin P.

    1993-01-01

    Progress made under the subject grant in the period from 1 Nov. 1992 to 31 May 1993 is presented. The research involves the continued development of the Large Angle Magnetic Suspension Test Fixture (LAMSTF) and also the recommissioning of an additional piece of exisiting hardware. During the period in question, the initial configuration of LAMSTF was completed and made routinely and reliably operational. A digital phase advance controller was completed and documented. The goal of a controlled 360 deg rotation was achieved. Work started on the recommissioning of the Annular Suspension and Pointing System (ASPS). Work completed during the report period included: modeling; position sensing; controller; support of the Second International Symposium on Magnetic Suspension Technology; and recommissioning of the Annular Suspension and Pointing System.

  17. Dual LED/incandescent security fixture

    DOEpatents

    Gauna, Kevin Wayne

    2005-06-21

    A dual LED and incandescent security lighting system uses a hybrid approach to LED illumination. It combines an ambient LED illuminator with a standard incandescent lamp on a motion control sensor. The LED illuminator will activate with the onset of darkness (daylight control) and typically remain on during the course of the night ("always on"). The LED illumination, typically amber, is sufficient to provide low to moderate level lighting coverage to the wall and ground area adjacent to and under the fixture. The incandescent lamp is integrated with a motion control circuit and sensor. When movement in the field of view is detected (after darkness), the incandescent lamp is switched on, providing an increased level of illumination to the area. Instead of an "always on" LED illuminator, the LEDs may also be switched off when the incandescent lamp is switched on.

  18. Evaluation of shock mitigating materials in a V-band pyroshock environment simulated with a resonant fixture

    SciTech Connect

    Bateman, V.I.; Brown, F.A.

    1993-12-31

    An explosively activated V-band joint is used on a multistage rocket payload to release components at prescribed times in the rocket`s flight and creates a pyroshock environment that the other payload components must survive. Accelerometer response data was measured close to an actual V-band pyroshock. With the shock spectra calculated from these data, a resonant fixture was designed to simulate a V-band pyroshock event. The characteristics of the data and the design process are described. Laboratory tests were conducted to determine that the desired shock spectra with an unusually high knee at about 8,000 Hz. was produced with the resonant fixture. The fixture was then mounted on a 29 in. diameter, 2 in. thick plate simulation of a payload plate. Simulated electronic components were also mounted on the plate. The pyroshock environment simulation was created by the resonant fixture response to a projectile impact, and the component response to the environment was measured at the electronic components. The component responses to the pyroshock were measured with five different shock mitigating materials inserted between the resonant fixture and the payload plate simulation, and the peak response values were tabulated.

  19. Fixture For Drilling And Tapping A Curved Workpiece

    NASA Technical Reports Server (NTRS)

    Espinosa, P. S.; Lockyer, R. T.

    1992-01-01

    Simple fixture guides drilling and tapping of holes in prescribed locations and orientations on workpiece having curved surface. Tool conceived for use in reworking complexly curved helicopter blades made of composite materials. Fixture is block of rigid foam with epoxy filler, custom-fitted to surface contour, containing bushings and sleeves at drilling and tapping sites. Bushings changed, so taps and drills of various sizes accommodated. In use, fixture secured to surface by hold-down bolts extending through sleeves and into threads in substrate.

  20. Development of a Dovetail Fretting Fatigue Fixture for Turbine Engine Materials (Preprint)

    DTIC Science & Technology

    2006-03-01

    of the costliest sources of in-service damage related to high cycle fatigue ( HCF ) in the US Air Force [3]. The objective of this work was to...Nickel based superalloy Rene ’88DT, respectively. The fixture was designed to directly measure the contact forces on the specimen which is an...Testing and analysis was conducted on Ti-6Al-4V and Rene ’88DT specimens and pads. Finite element method (FEM) analysis is used to confirm the

  1. Investigation into the reasons for preventable drug related admissions to a medical admissions unit: observational study

    PubMed Central

    Howard, R; Avery, A; Howard, P; Partridge, M

    2003-01-01

    Objective: To describe the drugs and types of medicine management problems most frequently associated with preventable drug related admissions to an acute medical admissions unit. Design: Observation study. Setting: Medical admissions unit in a teaching hospital in Nottingham, UK. Participants: 4093 patients seen by pharmacists on the medical admissions unit between 1 January and 30 June 2001. Main outcome measures: Proportion of admissions that were drug related and preventable, classification of the underlying causes of preventable drug related admissions, and identification of drugs most commonly associated with preventable drug related admissions. Results: Of the admissions seen by pharmacists, 265 (6.5%) were judged to be drug related and 178 (67%) of these were judged to be preventable. Preventable admissions were mainly due to problems with prescribing (63 cases (35%)), monitoring (46 cases (26%)), and adherence to medication (53 cases (30%)). The drugs most commonly implicated were NSAIDs, antiplatelets, antiepileptics, hypoglycaemics, diuretics, inhaled corticosteroids, cardiac glycosides, and beta-blockers. Conclusions: Potentially preventable drug related morbidity was associated with 4.3% of admissions to a medical admissions unit. In 91% of cases these admissions were related to problems with either prescribing, monitoring, or adherence. PMID:12897361

  2. 4. FRONT PORCH EXTERIOR DETAIL SHOWING PLANK CEILING, LIGHT FIXTURE, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. FRONT PORCH EXTERIOR DETAIL SHOWING PLANK CEILING, LIGHT FIXTURE, AND DORIC COLUMNS. VIEW TO SOUTH. - Big Creek Hydroelectric System, Big Creek Town, Operator House, Orchard Avenue south of Huntington Lake Road, Big Creek, Fresno County, CA

  3. 46 CFR 111.75-20 - Lighting fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... reference; see 46 CFR 110.10-1). (b) Each fixture globe, lens, or diffuser must have a high strength guard or be made of high strength material, except in an accommodation space, navigating bridge, gyro...

  4. 46 CFR 111.75-20 - Lighting fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... reference; see 46 CFR 110.10-1). (b) Each fixture globe, lens, or diffuser must have a high strength guard or be made of high strength material, except in an accommodation space, navigating bridge, gyro...

  5. 46 CFR 111.75-20 - Lighting fixtures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... reference; see 46 CFR 110.10-1). (b) Each fixture globe, lens, or diffuser must have a high strength guard or be made of high strength material, except in an accommodation space, navigating bridge, gyro...

  6. 46 CFR 111.75-20 - Lighting fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... reference; see 46 CFR 110.10-1). (b) Each fixture globe, lens, or diffuser must have a high strength guard or be made of high strength material, except in an accommodation space, navigating bridge, gyro...

  7. 46 CFR 111.75-20 - Lighting fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... reference; see 46 CFR 110.10-1). (b) Each fixture globe, lens, or diffuser must have a high strength guard or be made of high strength material, except in an accommodation space, navigating bridge, gyro...

  8. VIEW OF LAMP FIXTURE (EXTERIOR) ADJACENT TO ENTRANCE AT SOUTHWEST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF LAMP FIXTURE (EXTERIOR) ADJACENT TO ENTRANCE AT SOUTHWEST CORNER OF BUILDING 23, FACING NORTH - Roosevelt Base, Auditorium-Gymnasium, West Virginia Street between Richardson & Reeves Avenues, Long Beach, Los Angeles County, CA

  9. Detail; Street Car Waiting House, support for exterior light fixture ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail; Street Car Waiting House, support for exterior light fixture - North Philadelphia Station, Street Car Waiting House, 2900 North Broad Street, on northwest corner of Broad Street & Glenwood Avenue, Philadelphia, Philadelphia County, PA

  10. Detail view of light fixture on south facade National ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of light fixture on south facade - National Home for Disabled Volunteer Soldiers, Pacific Branch, Old Administration Building, 11301 Wilshire Boulevard, West Los Angeles, Los Angeles County, CA

  11. Seeking the Admission Hybrid

    ERIC Educational Resources Information Center

    Lucido, Jerome A.

    2012-01-01

    When one thinks of seminal publications in college admission, the first piece that comes to mind is B. Alden Thresher's "College Admissions in the Public Interest" (1966). Thresher's work, relevant to this day, is credited with being the foundational document of the admission profession. McDonough and Robertson's 1995 study, commissioned by NACAC,…

  12. Simulation of pyroshock environments using a tunable resonant fixture

    DOEpatents

    Davie, N.T.

    1996-10-15

    Disclosed are a method and apparatus for simulating pyrotechnic shock for the purpose of qualifying electronic components for use in weapons, satellite, and aerospace applications. According to the invention, a single resonant bar fixture has an adjustable resonant frequency in order to exhibit a desired shock response spectrum upon mechanical impact. The invention eliminates the need for availability of a large number of different fixtures, capable of exhibiting a range of shock response characteristics, in favor of a single tunable system. 32 figs.

  13. Simulation of pyroshock environments using a tunable resonant fixture

    SciTech Connect

    Davie, Neil T.

    1996-01-01

    Disclosed are a method and apparatus for simulating pyrotechnic shock for the purpose of qualifying electronic components for use in weapons, satellite, and aerospace applications. According to the invention, a single resonant bar fixture has an adjustable resonant frequency in order to exhibit a desired shock response spectrum upon mechanical impact. The invention eliminates the need for availability of a large number of different fixtures, capable of exhibiting a range of shock response characteristics, in favor of a single tunable system.

  14. Simulation of pyroshock environments using a tunable resonant fixture

    SciTech Connect

    Davie, N.T.

    1993-09-30

    Disclosed are a method and apparatus for simulating pyrotechnic shock for the purpose of qualifying electronic components for use in weapons, satellite, and aerospace applications. According to the invention, a single resonant bar fixture has an adjustable resonant frequency in order to exhibit a desired shock response spectrum upon mechanical impact. The invention eliminates the need for availability of a large number of different fixtures, capable of exhibiting a range of shock response characteristics, in favor of a single tunable system.

  15. Investigation of a light fixture fire

    DOE PAGES

    Jurney, James D.; Cournoyer, Michael E.; Trujillo, Stanley; ...

    2016-04-16

    Metal-halide lamps produce light by discharging an electric arc through a gaseous mixture of vaporized mercury and metal halides. Metal-halide lamps for use in spaces with lower mounting heights can produce excessive visual glare in the normal, higher field-of-view unless they are equipped with prismatic lenses. Should the bulb fail, high internal operating pressure of the arc tube can launch fragments of arc tube at high velocity in all directions, striking the outer bulb of the lamp with enough force to cause the outer bulb to break. This article reports an investigation of a light fixture fire and reviews amore » case study of a metal-halide lamp fire. We reported on causal analysis of the metal-halide lamp fire uncovered contributing factors that created the environment in which the incident occurred. Latent organizational conditions that created error-likely situations or weakened defenses were identified and controlled. Lastly, effective improvements that reduce the probability or consequence of similar metal-halide lamp fire incidents were implemented.« less

  16. Investigation of a light fixture fire

    SciTech Connect

    Jurney, James D.; Cournoyer, Michael E.; Trujillo, Stanley; Schreiber, Stephen B.

    2016-04-16

    Metal-halide lamps produce light by discharging an electric arc through a gaseous mixture of vaporized mercury and metal halides. Metal-halide lamps for use in spaces with lower mounting heights can produce excessive visual glare in the normal, higher field-of-view unless they are equipped with prismatic lenses. Should the bulb fail, high internal operating pressure of the arc tube can launch fragments of arc tube at high velocity in all directions, striking the outer bulb of the lamp with enough force to cause the outer bulb to break. This article reports an investigation of a light fixture fire and reviews a case study of a metal-halide lamp fire. We reported on causal analysis of the metal-halide lamp fire uncovered contributing factors that created the environment in which the incident occurred. Latent organizational conditions that created error-likely situations or weakened defenses were identified and controlled. Lastly, effective improvements that reduce the probability or consequence of similar metal-halide lamp fire incidents were implemented.

  17. Head tracker evaluation utilizing the dynamic tracker test fixture

    NASA Astrophysics Data System (ADS)

    La Moure Shattuck, Judson, III; Parisi, Vincent M., II; Smerdon, Arryn J.

    2007-04-01

    In military aviation, head tracker technologies have become increasingly important to track the pilot's head position and orientation, allowing the user to quickly interact with the operational environment. This technology allows the pilot to quickly acquire items of interest and see Fighter Data Link type information. Acquiring the target on a helmet-mounted tracker/display which can automatically slew a weapon's seeker is far more efficient than having to point at the target with the nose of the aircraft as previously required for the heads-up display (HUD) type of target acquisition. The United States Air Force (USAF) has used and evaluated a variety of helmet-mounted trackers for incorporation into their high performance aircrafts. The Dynamic Tracker Test Fixture (DTTF) was designed by the Helmet-Mounted Sensory Technology (HMST) laboratory to accurately measure rotation in one plane both static and dynamic conditions for the purpose of evaluating the accuracy of head trackers, including magnetic, inertial, and optical trackers. This paper describes the design, construction, capabilities, limitations, and performance of the DTTF.

  18. Lexical Profiles of Thailand University Admission Tests

    ERIC Educational Resources Information Center

    Cherngchawano, Wirun; Jaturapitakkul, Natjiree

    2014-01-01

    University Admission Tests in Thailand are important documents which reflect Thailand's education system. To study at a higher education level, all students generally need to take the University Admission Tests designed by the National Institute of Educational Testing Service (NIETS). For the English test, vocabulary and reading comprehension is…

  19. Grade Inflation and Law School Admissions

    ERIC Educational Resources Information Center

    Wongsurawat, Winai

    2008-01-01

    Purpose: The purpose of this paper is to evaluate the evidence on whether grade inflation has led to an increasing emphasis on standardized test scores as a criterion for law school admissions. Design/methodology/approach: Fit probabilistic models to admissions data for American law schools during the mid to late 1990s, a period during which…

  20. Strategies and Trends in Admissions Research

    ERIC Educational Resources Information Center

    Fincher, Cameron

    1975-01-01

    Noting that the technical service rendered by the national testing agencies may be an undesirable tradeoff for the active involvement of admissions workers in admissions research, the author suggests that the use of decision theory, quasi-actuarial assessment, quasi-experimental design, and program evaluation strategies would place admissions…

  1. Implant Fixture Heat Transfer During Abutment Preparation.

    PubMed

    Aleisa, Khalil; Alkeraidis, Abdullah; Al-Dwairi, Ziad Nawaf; Altahawi, Hamdi; Lynch, Edward

    2015-06-01

    The purpose of the study was to evaluate the effect of water flow rate on the heat transmission in implants during abutment preparation using a diamond bur in a high-speed dental turbine. Titanium-alloy abutments (n = 32) were connected to a titanium-alloy implant embedded in an acrylic resin within a water bath at a controlled temperature of 37°C. The specimens were equally distributed into 2 groups (16 each) according to the water flow rate used during the preparation phase. Group 1 had a water flow rate of 24 mL/min, and group 2 had a water flow rate of 40 mL/min. Each abutment was prepared in the axial plane for 1 minute and in the occlusal plane for 1 minute with a coarse tapered diamond bur using a high-speed dental handpiece. Thermocouples embedded at the cervix of the implant surface were used to record the temperature of heat transmission from the abutment preparation. Heat generation was measured at 3 distinct times (immediately and 30 seconds and 60 seconds after the end of preparation). Statistical analyses were carried out using 2-way analysis of variance and the Student t test. Water flow rates (24 mL vs 40 mL) and time interval had no statistically significant effect on the implant's temperature change during the abutment preparation stage (P = .431 and P = .064, respectively). Increasing the water flow rate from 24 to 40 mL/min had no influence on the temperature of the implant fixture recorded during preparation of the abutment.

  2. A Novel Short Sample Mounting Fixture for Critical Current Measurements

    NASA Astrophysics Data System (ADS)

    Chesny, Ph.; Fazilleau, Ph.; Gheller, J.-M.

    2006-04-01

    One of the essential characteristics of a superconducting wire is its critical current, defined as the maximal current at given temperature and magnetic field for which it remains superconducting. In order to make measurements from 1.8 K to 4.2 K and up to 1200 A at very low pressure, we studied and manufactured an original short sample mount; it is made of are two co-axial current leads (46 mm and 24 mm of external diameter) terminating with two Nb3Sn buss bars. Annular space has been dimensioned in order to minimize the pressure drop for sub atmospheric operations (use of a 600 m3/h roots at 15 mbar with adjustable speed). The LHe supply is achieved with a transfer line covered with Kapton insulation. It is located inside the internal current lead and equipped with a JT valve. The sample to be measured, V A M A S type (Versailles project on Advanced MAterials and Standards), is assembled at the low end of the two buss bars. The quality of the electrical contacts is ensured by simple tightening. This paper presents the current lead computations, the test facility design and realization as well as the first measurements achieved with the short sample mounting fixture.

  3. Eliminating Standardized Tests in College Admissions: The New Affirmative Action?

    ERIC Educational Resources Information Center

    Zwick, Rebecca

    1999-01-01

    Eliminating the Scholastic Aptitude Test for college admissions might seem a form of covert affirmative action. Although it is possible to design a workable admissions policy that excludes standardized tests (as 15 percent of colleges have done), banishing admissions tests to further a social-policy goal indirectly is unsound policy. (Contains 25…

  4. Economic analysis of greenhouse lighting: light emitting diodes vs. high intensity discharge fixtures.

    PubMed

    Nelson, Jacob A; Bugbee, Bruce

    2014-01-01

    Lighting technologies for plant growth are improving rapidly, providing numerous options for supplemental lighting in greenhouses. Here we report the photosynthetic (400-700 nm) photon efficiency and photon distribution pattern of two double-ended HPS fixtures, five mogul-base HPS fixtures, ten LED fixtures, three ceramic metal halide fixtures, and two fluorescent fixtures. The two most efficient LED and the two most efficient double-ended HPS fixtures had nearly identical efficiencies at 1.66 to 1.70 micromoles per joule. These four fixtures represent a dramatic improvement over the 1.02 micromoles per joule efficiency of the mogul-base HPS fixtures that are in common use. The best ceramic metal halide and fluorescent fixtures had efficiencies of 1.46 and 0.95 micromoles per joule, respectively. We also calculated the initial capital cost of fixtures per photon delivered and determined that LED fixtures cost five to ten times more than HPS fixtures. The five-year electric plus fixture cost per mole of photons is thus 2.3 times higher for LED fixtures, due to high capital costs. Compared to electric costs, our analysis indicates that the long-term maintenance costs are small for both technologies. If widely spaced benches are a necessary part of a production system, the unique ability of LED fixtures to efficiently focus photons on specific areas can be used to improve the photon capture by plant canopies. Our analysis demonstrates, however, that the cost per photon delivered is higher in these systems, regardless of fixture category. The lowest lighting system costs are realized when an efficient fixture is coupled with effective canopy photon capture.

  5. Economic Analysis of Greenhouse Lighting: Light Emitting Diodes vs. High Intensity Discharge Fixtures

    PubMed Central

    Nelson, Jacob A.; Bugbee, Bruce

    2014-01-01

    Lighting technologies for plant growth are improving rapidly, providing numerous options for supplemental lighting in greenhouses. Here we report the photosynthetic (400–700 nm) photon efficiency and photon distribution pattern of two double-ended HPS fixtures, five mogul-base HPS fixtures, ten LED fixtures, three ceramic metal halide fixtures, and two fluorescent fixtures. The two most efficient LED and the two most efficient double-ended HPS fixtures had nearly identical efficiencies at 1.66 to 1.70 micromoles per joule. These four fixtures represent a dramatic improvement over the 1.02 micromoles per joule efficiency of the mogul-base HPS fixtures that are in common use. The best ceramic metal halide and fluorescent fixtures had efficiencies of 1.46 and 0.95 micromoles per joule, respectively. We also calculated the initial capital cost of fixtures per photon delivered and determined that LED fixtures cost five to ten times more than HPS fixtures. The five-year electric plus fixture cost per mole of photons is thus 2.3 times higher for LED fixtures, due to high capital costs. Compared to electric costs, our analysis indicates that the long-term maintenance costs are small for both technologies. If widely spaced benches are a necessary part of a production system, the unique ability of LED fixtures to efficiently focus photons on specific areas can be used to improve the photon capture by plant canopies. Our analysis demonstrates, however, that the cost per photon delivered is higher in these systems, regardless of fixture category. The lowest lighting system costs are realized when an efficient fixture is coupled with effective canopy photon capture. PMID:24905835

  6. Heat transfer assembly for a fluorescent lamp and fixture

    DOEpatents

    Siminovitch, M.J.; Rubenstein, F.M.; Whitman, R.E.

    1992-12-29

    In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure. 11 figs.

  7. Heat transfer assembly for a fluorescent lamp and fixture

    DOEpatents

    Siminovitch, Michael J.; Rubenstein, Francis M.; Whitman, Richard E.

    1992-01-01

    In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure.

  8. Development of a ferromagnetic rotary vacuum sealed spacecraft spin fixture

    NASA Technical Reports Server (NTRS)

    Levine, M. B.

    1977-01-01

    A number of successful spacecraft tests were conducted on an environmental spin fixture which utilizes a ferrofluidic rotary vacuum seal. The 27 cm (10.5 inch) diameter fixture drive shaft supports and spins communications satellites during flight acceptance testing in a thermal vacuum chamber. The drive shaft rotary seal serves to maintain the canned drive system electro-mechanical components at ambient pressure within the space simulator. The ferromagnetic fluid seal was chosen over conventional mechanical sealing devices for its zero-leakage, zero-wear, and minimum friction drag characteristics, as well as its high reliability potential.

  9. Welding fixture for nuclear fuel pin cladding assemblies

    DOEpatents

    Oakley, D.J.; Feld, S.H.

    1984-02-22

    A welding fixture is described for locating a driver sleeve about the open end of a nuclear fuel pin cladding. The welding fixture includes a holder provided with an open cavity having shoulders for properly positioning the driver sleeve, the end cap, and a soft, high temperature resistant plastic protective sleeve that surrounds a portion of the end cap stem. Ejected contaminant particles spewed forth by closure of the cladding by pulsed magnetic welding techniques are captured within a contamination trap formed in the holder for ultimate removal and disposal of contaminating particles along with the holder.

  10. Welding fixture for nuclear fuel pin cladding assemblies

    DOEpatents

    Oakley, David J.; Feld, Sam H.

    1986-01-01

    A welding fixture for locating a driver sleeve about the open end of a nuclear fuel pin cladding. The welding fixture includes a holder provided with an open cavity having shoulders for properly positioning the driver sleeve, the end cap, and a soft, high temperature resistant plastic protective sleeve that surrounds a portion of the end cap stem. Ejected contaminant particles spewed forth by closure of the cladding by pulsed magnetic welding techniques are captured within a contamination trap formed in the holder for ultimate removal and disposal of contaminating particles along with the holder.

  11. What Admissions Officials Think

    ERIC Educational Resources Information Center

    Hoover, Eric

    2008-01-01

    Over the past two decades, college admissions has become a prime-time preoccupation. Most people know at least something about the process, especially if they have a teenager in high school and a college guide on their coffee table. Nonetheless, widespread public misconceptions persist about admissions requirements, the selection process, and the…

  12. The Administration of Admissions

    ERIC Educational Resources Information Center

    Campbell, Clifford C.

    1978-01-01

    Among all the tasks of the admissions officer in developing a successful marketing program, the hardest may be that of convincing other college administrators of the importance of admissions to the institution's survival. Discussed are long-range planning, budgeting, staff selection and training, and implementing a plan. (Author/LBH)

  13. Technology in International Admissions

    ERIC Educational Resources Information Center

    White, Elizabeth

    2012-01-01

    In a relatively short time, technology applications have become an essential feature of the admissions business. They make the jobs of international admissions professionals easier in many ways, allowing for more robust communication with applicants and counselors, a streamlined application process, and quicker access to information about…

  14. Fixture and layout planning for reconfigurable workcells. LDRD final report

    SciTech Connect

    Strip, D.; Phillips, C.

    1994-06-01

    The work in this program covered four primary areas: solid modeling, path planning, modular fixturing, and stability analysis. This report contains highlights of results from the program, references to published reports, and, in an appendix, a currently unpublished report which has been accepted for journal publication, but has yet to appear.

  15. Make a Mystery Circuit with a Bar Light Fixture

    ERIC Educational Resources Information Center

    Lietz, Martha

    2007-01-01

    Teachers have been building mystery circuits or so-called "black box circuits" to use as a demonstration with their students for years. This paper presents an easy way to make simple mystery circuits using inexpensive light fixtures (see Fig. 1) available at almost any home improvement store. In a black box circuit, only the lightbulbs are visible…

  16. DETAIL OF THE DRUMSHAPED LIGHT FIXTURE IN THE FOYER. VIEW ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL OF THE DRUM-SHAPED LIGHT FIXTURE IN THE FOYER. VIEW FACING SOUTH - Camp H.M. Smith and Navy Public Works Center Manana Title VII (Capehart) Housing, U-Shaped Two-Bedroom Duplex Type 1, Acacia Road, Birch Circle, and Cedar Drive, Pearl City, Honolulu County, HI

  17. Handling fixture for soldering round wires to FCC

    NASA Technical Reports Server (NTRS)

    Loggins, R.; Martineck, H. G.

    1971-01-01

    Fixture holds flat conductor cable and wires in position until after soldering of contacting conductor ends and potting of junctions. Device provides for proper spacing of wires and adequate access for soldered joints during fabrication, and positions mold halves during potting operation.

  18. 75 FR 5544 - Energy Conservation Program: Energy Conservation Standards for Metal Halide Lamp Fixtures: Public...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-03

    ... for Metal Halide Lamp Fixtures: Public Meeting and Availability of the Framework Document AGENCY... conservation standards for certain metal halide lamp fixtures. This document announces that the period for... metal halide lamp fixtures and provide docket number EERE-2009-BT-STD-0018 and/or RIN number 1904-...

  19. Prototype wash water renovation system integration with government-furnished wash fixture

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The requirements of a significant quantity of proposed life sciences experiments in Shuttle payloads for available wash water to support cleansing operations has provided the incentive to develop a technique for wash water renovation. A prototype wash water waste renovation system which has the capability to process the waste water and return it to a state adequate for reuse in a typical cleansing fixture designed to support life science experiments was investigated. The resulting technology is to support other developments efforts pertaining to water reclamation by serving as a pretreatment step for subsequent reclamation procedures.

  20. Student Admission and Attendance.

    ERIC Educational Resources Information Center

    Majestic, Ann L.

    1988-01-01

    Considers the North Carolina statutes that define the process for admitting students to public schools and ensuring their attendance. Examines cases relating to issues of school admission and compulsory attendance. (MLF)

  1. Hospice Admission Assessment.

    PubMed

    Moon, Paul J

    2017-04-01

    Hospice admission assessment is a pivotal encounter for patient/family and hospice representative. For patient/family, the admission is the threshold by which a particular level of care can commence and, symbolically, a certain marker in health status trajectory is reached. For hospice representative, the admission episode is an occasion to inaugurate an ambience that can serve to frame future hospice care experiences for the patient/family. Through a narrative lens, hospice admission assessment can be seen as experiential time and space, where patient's and family's stories are mindfully and deliberately witnessed and explored. Through the practice of narrative mining, the hospice representative can better understand others' offered stories of reality, which will better inform the plan of palliation and hospice care.

  2. Large angle magnetic suspension text fixture

    NASA Technical Reports Server (NTRS)

    Britcher, Colin P.

    1995-01-01

    In lieu of a final report for this project for the period 1 April 1995 through 31 October 1995, a compilation of three reports are included herein. The three reports are: (1) 'Design and Implementation of a Digital Controller for a Magnetic Suspension and Vernier Pointing System', (2) 'Influence of Eddy Currents on the Dynamic Characteristics of Magnetic Suspensions and Magnetic Bearings', and (3) 'Design and Implementation of a Digital Controller for a Magnetic Suspension and Vernier Pointing System'.

  3. Characterizing nanoscale scanning probes using electron microscopy: A novel fixture and a practical guide

    SciTech Connect

    Jacobs, Tevis D. B.; Wabiszewski, Graham E.; Goodman, Alexander J.; Carpick, Robert W.

    2016-01-15

    The nanoscale geometry of probe tips used for atomic force microscopy (AFM) measurements determines the lateral resolution, contributes to the strength of the tip-surface interaction, and can be a significant source of uncertainty in the quantitative analysis of results. While inverse imaging of the probe tip has been used successfully to determine probe tip geometry, direct observation of the tip profile using electron microscopy (EM) confers several advantages: it provides direct (rather than indirect) imaging, requires fewer algorithmic parameters, and does not require bringing the tip into contact with a sample. In the past, EM-based observation of the probe tip has been achieved using ad hoc mounting methods that are constrained by low throughput, the risk of contamination, and repeatability issues. We report on a probe fixture designed for use in a commercial transmission electron microscope that enables repeatable mounting of multiple AFM probes as well as a reference grid for beam alignment. This communication describes the design, fabrication, and advantages of this probe fixture, including full technical drawings for machining. Further, best practices are discussed for repeatable, non-destructive probe imaging. Finally, examples of the fixture’s use are described, including characterization of common commercial AFM probes in their out-of-the-box condition.

  4. X-band slotted array test panel and test fixture

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Data from the development of the X-band slotted array test band, X-band array test fixture, and the X/L-band test fixture for the Support Instrumentation Requirements program are documented. An X-band array was built and installed with an existing L-band module in such a way as to permit antenna pattern measurements in a series of nonplanar configurations that might simulate the thermal effects of nonuniform solar illumination on the array in a space environment. This was accomplished with eight X-band subpanels mounted adjacently on individually adjusted supports which were then co-mounted to a larger frame which served to mount and physically distort the existing L-band module. The L-band module is a heavy electrical breadboard array section that was fabricated to demonstrate the performance capabilities of a slotted waveguide array at L-band frequencies. Drawings, mechanical analysis, and descriptions of test configurations are presented.

  5. Variation in rates of hospital admission for appendicitis in Wales.

    PubMed Central

    West, R R; Carey, M J

    1978-01-01

    In a study designed to investigate the variations in rates of admission to hospital for appendicitis in Wales Hospital Activity Analysis listings were analysed according to the sex and age of the patients and the month and day of the week of admission. The incidence of hospitalisation was greatest among boys aged 10-14 and girls aged 15-19. The number of admissions was higher on weekdays than at weekends, but there were no seasonal variations. Durations of stay differed between the 17 health districts. We conclude that admission rates vary mainly because of differing hospital admission policies. Admission is not wholly governed by the sudden onset of abdominal pain; other factors include the threshold of consultation of each patient, the referral habits of general practitioners, the availability of hospital beds, and the degree to which doctors and patients expect admission. PMID:656866

  6. Large Angle Magnetic Suspension Test Fixture

    NASA Technical Reports Server (NTRS)

    Britcher, Colin P.; Huang, Jen-Kuang

    1997-01-01

    Progress in the areas of eddy current computations, modelling and analysis, design optimization methods, wind tunnel Magnetic Suspension and Balance Systems (MSBS), payload pointing and vibration isolation systems, and system identification is reported. Research accomplishments facilitated the demonstration of several new developments in the field of magnetic suspension technology.

  7. Stability characterizations of fixtured rigid bodies with Coulomb friction

    SciTech Connect

    PANG,J.S.; TRINKLE,JEFFREY C.

    2000-02-15

    This paper formally introduces several stability characterizations of fixtured three-dimensional rigid bodies initially at rest and in unilateral contact with Coulomb friction. These characterizations, weak stability and strong stability, arise naturally from the dynamic model of the system, formulated as a complementarity problem. Using the tools of complementarity theory, these characterizations are studied in detail to understand their properties and to develop techniques to identify the stability classifications of general systems subjected to known external loads.

  8. Remediation plan for fluorescent light fixtures containing polychlorinated biphenyls (PCBs)

    SciTech Connect

    1992-04-30

    This report describes the remedial action to achieve compliance with 29 CFR 1910 Occupational Safety and Health Administration (OSHA) requirements of fluorescent light fixtures containing PCBs at K-25 site. This remedial action is called the Remediation Plan for Fluorescent Light Fixtures Containing PCBs at the K-25 Site (The Plan). The Plan specifically discusses (1) conditions of non-compliance, (2) alternative solutions, (3) recommended solution, (4) remediation plan costs, (5) corrective action, (6) disposal of PCB waste, (7) training, and (8) plan conclusions. The results from inspections by Energy Systems personnel in 2 buildings at K-25 site and statistical extension of this data to 91 selected buildings at the K-25 site indicates that there are approximately 28,000 fluorescent light fixtures containing 47,036 ballasts. Approximately 38,531 contain PCBs and 2,799 of the 38,531 ballasts are leaking PCBs. Review of reportable occurrences at K-25 for the 12 month period of September 1990 through August 1991 shows that Energy Systems personnel reported 69 ballasts leaking PCBs. Each leaking ballast is in non-compliance with 29 CFR 1910 - Table Z-1-A. The age of the K-25 facilities indicate a continued and potential increase in ballasts leaking PCBs. This report considers 4 alternative solutions for dealing with the ballasts leaking PCBs. The advantages and disadvantages of each alternative solution are discussed and ranked using cost of remediation, reduction of health risks, and compliance with OSHA as criteria.

  9. Large angle magnetic suspension test fixture

    NASA Technical Reports Server (NTRS)

    Britcher, Colin P. (Principal Investigator); Huang, Jen-Kuang (Principal Investigator)

    1996-01-01

    Good progress is being made in several major areas. These include eddy current modelling and analysis, design optimization methods, wind tunnel Magnetic Suspension and Balance Systems (MSBS), payload pointing and vibration isolation systems, and system identification. In addition, another successful International Symposium has been completed, with the Proceedings being printed at the time of writing. These activities continue current work under this Grant and extend previous work on magnetic suspension systems and devices in the Guidance and Control Branch and will permit the demonstration of several new developments in the field of magnetic suspension technology.

  10. High-output LED-based light engine for profile lighting fixtures with high color uniformity using freeform reflectors.

    PubMed

    Gadegaard, Jesper; Jensen, Thøger Kari; Jørgensen, Dennis Thykjær; Kristensen, Peter Kjær; Søndergaard, Thomas; Pedersen, Thomas Garm; Pedersen, Kjeld

    2016-02-20

    In the stage lighting and entertainment market, light engines (LEs) for lighting fixtures are often based on high-intensity discharge (HID) bulbs. Switching to LED-based light engines gives possibilities for fast switching, additive color mixing, a longer lifetime, and potentially, more energy-efficient systems. The lumen output of a single LED is still not sufficient to replace an HID source in high-output profile fixtures, but combining multiple LEDs can create an LE with a similar output, but with added complexity. This paper presents the results of modeling and testing such a light engine. Custom ray-tracing software was used to design a high-output red, green and blue LED-based light engine with twelve CBT-90 LEDs using a dual-reflector principle. The simulated optical system efficiency was 0.626 with a perfect (R=1) reflector coating for light delivered on a target surface through the entire optical system. A profile lighting fixture prototype was created, and provided an output of 6744 lumen and an efficiency of 0.412. The lower efficiency was mainly due to a non-optimal reflector coating, and the optimized design is expected to reach a significantly higher efficiency.

  11. Large angle magnetic suspension test fixture

    NASA Technical Reports Server (NTRS)

    Britcher, Colin P.

    1994-01-01

    Over the past few decades, research has proven the feasibility of the concept of noncontacting magnetic bearing systems which operate with no wear or vibration. As a result, magnetic bearing systems are beginning to emerge as integral parts of modern industrial and aerospace systems. Further applications research is still required. NASA has loaned an existing magnetic bearing device, the Annular Suspension and Pointing System (ASPS), to ODU to permit student design teams the opportunity to pursue some of these studies. The ASPS is a protoype for a high-accuracy space payload pointing and vibration isolation system. The project objectives are to carry out modifications and improvements to the ASPS hardware to permit recommissioning in a 1-g (ground-based) environment. Following recommissioning, new applications will be studied and demonstrated, including a rotary joint for solar panels. The first teams designed and manufactured pole shims to reduce the air-gaps and raise the vertical force capability as well as on control system studies. The most recent team concentrated on the operation of a single bearing station, which was successfully accomplished with a PC-based digital controller. The paper will review the history and technical background of the ASPS hardware, followed by presentation of the progress made and the current status of the project.

  12. Immigration, moving house and psychiatric admissions.

    PubMed

    Johansson, L M; Sundquist, J; Johansson, S E; Bergman, B

    1998-08-01

    This study was designed to elucidate psychiatric admission rates for native Swedes and foreign-born individuals during the period 1991-1994, when Sweden had a great influx of refugees. During the same period, and even earlier, psychiatric in-patient care had been reduced. Tests of differences between Swedes and foreign-born individuals in first psychiatric admission rates were performed using Poisson regressions, and the risk of a readmission was assessed using a proportional hazard model. Foreign-born individuals and native Swedes, both males and females, showed a similar admission pattern with regard to the number of admissions. Foreign-born males under 55 years of age and foreign-born females under 35 years of age had significantly higher admission rates than native Swedes. In total, native Swedes, both males and females, were hospitalized for a significantly longer period than the foreign-born subjects. About 43% of the patients were readmitted. The risk of a readmission was significantly increased among those with a high rate of internal migration. The high admission rates for young foreign-born individuals might be explained by a high incidence of mental illness owing to the trauma of being violently forced to migrate, acculturation difficulties, or unsatisfactory social circumstances such as high unemployment. The shorter hospitalization time could be due to undertreatment or less serious mental illness.

  13. The Admissions Equity Struggle

    ERIC Educational Resources Information Center

    Freedman, Eric

    2012-01-01

    It has been a long, litigious road from Heman Sweatt, an African-American mail carrier who wanted to attend the prestigious, all-White law school at the University of Texas at Austin in 1946, to Abigail Fisher, a White high school student who failed to win undergraduate admission to the same university a half-century later. Depending on what the…

  14. A parallel microfluidic channel fixture fabricated using laser ablated plastic laminates for electrochemical and chemiluminescent biodetection of DNA

    PubMed Central

    Edwards, Thayne L.; Harper, Jason C.; Polsky, Ronen; Lopez, DeAnna M.; Wheeler, David R.; Allen, Amy C.; Brozik, Susan M.

    2011-01-01

    Herein is described the fabrication and use of a plastic multilayer 3-channel microfluidic fixture. Multilayer devices were produced by laser machining of plastic polymethylmethacrylate and polyethyleneterapthalate laminates by ablation. The fixture consisted of an array of nine individually addressable gold or gold/ITO working electrodes, and a resistive platinum heating element. Laser machining of both the fluidic pathways in the plastic laminates, and the stencil masks used for thermal evaporation to form electrode regions on the plastic laminates, enabled rapid and inexpensive implementation of design changes. Electrochemiluminescence reactions in the fixture were achieved and monitored through ITO electrodes. Electroaddressable aryl diazonium chemistry was employed to selectively pattern gold electrodes for electrochemical multianalyte DNA detection from double stranded DNA (dsDNA) samples. Electrochemical detection of dsDNA was achieved by melting of dsDNA molecules in solution with the integrated heater, allowing detection of DNA sequences specific to breast and colorectal cancers with a non-specific binding control. Following detection, the array surface could be renewed via high temperature (95 °C) stripping using the integrated heating element. This versatile and simple method for prototyping devices shows potential for further development of highly integrated, multi-functional bioanalytical devices. PMID:22276087

  15. Admissions Criteria in Teacher Education.

    ERIC Educational Resources Information Center

    Schwanke, Dean

    1981-01-01

    A review of the literature on the topic of admissions criteria in teacher education is presented. Bibliographic annotations review surveys, studies, models, and guidelines on various aspects of admissions criteria, as well as attracting and retaining quality students. (JN)

  16. Predicting Academic Success Using Admission Profiles

    ERIC Educational Resources Information Center

    Davidovitch, Nitza; Soen, Dan

    2015-01-01

    This study, conducted at a tertiary education institution in Israel, following two previous studies, was designed to deal again with a question that is a topic of debate in Israel and worldwide: Is there justification for the approach that considers restrictive university admission policies an efficient tool for predicting students' success at the…

  17. WICS: A Model for College and University Admissions

    ERIC Educational Resources Information Center

    Sternberg, Robert J.; Bonney, Christina R.; Gabora, Liane; Merrifield, Maegan

    2012-01-01

    This article outlines shortcomings of currently used university admissions tests and discusses ways in which they could potentially be improved, summarizing two projects designed to enhance college and university admissions. The projects were inspired by the augmented theory of successful intelligence, according to which successful intelligence…

  18. Error prediction for probes guided by means of fixtures

    NASA Astrophysics Data System (ADS)

    Fitzpatrick, J. Michael

    2012-02-01

    Probe guides are surgical fixtures that are rigidly attached to bone anchors in order to place a probe at a target with high accuracy (RMS error < 1 mm). Applications include needle biopsy, the placement of electrodes for deep-brain stimulation (DBS), spine surgery, and cochlear implant surgery. Targeting is based on pre-operative images, but targeting errors can arise from three sources: (1) anchor localization error, (2) guide fabrication error, and (3) external forces and torques. A well-established theory exists for the statistical prediction of target registration error (TRE) when targeting is accomplished by means of tracked probes, but no such TRE theory is available for fixtured probe guides. This paper provides that theory and shows that all three error sources can be accommodated in a remarkably simple extension of existing theory. Both the guide and the bone with attached anchors are modeled as objects with rigid sections and elastic sections, the latter of which are described by stiffness matrices. By relating minimization of elastic energy for guide attachment to minimization of fiducial registration error for point registration, it is shown that the expression for targeting error for the guide is identical to that for weighted rigid point registration if the weighting matrices are properly derived from stiffness matrices and the covariance matrices for fiducial localization are augmented with offsets in the anchor positions. An example of the application of the theory is provided for ear surgery.

  19. 10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Definitions concerning metal halide lamp ballasts and... FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Metal Halide Lamp Ballasts and Fixtures § 431.322 Definitions concerning metal halide lamp ballasts and fixtures. Ballast efficiency means, in the case of...

  20. Make a Mystery Circuit with a Bar Light Fixture

    NASA Astrophysics Data System (ADS)

    Lietz, Martha

    2007-04-01

    Teachers have been building mystery circuits or so-called "black box circuits" to use as a demonstration with their students for years. This paper presents an easy way to make simple mystery circuits using inexpensive light fixtures (see Fig. 1) available at almost any home improvement store.2 In a black box circuit, only the lightbulbs are visible and the wiring in these circuits is hidden from the students. The students are then presented with the challenge of deducing the nature of the electrical connections hidden by the black box. The students may remove one or more lightbulbs from the circuit to watch how the brightness of the other bulbs changes and, from this, deduce which bulbs are connected in series and which are connected in parallel.

  1. Grapple fixture for use with electromagnetic attachment mechanism

    NASA Technical Reports Server (NTRS)

    Monford, Jr., Leo G. (Inventor)

    1995-01-01

    An electromagnetic attachment mechanism for use as an end effector of a remote manipulator system. A pair of electromagnets 15A,15B, each with a U-shaped magnetic core with a pull-in coil 34 and two holding coils 35,36 are mounted by a spring suspension system 38,47 on a base plate 25 of the mechanism housing 30 with end pole pieces 21,22 adapted to move through openings in the base plate when the attractive force of the electromagnets is exerted on a strike plate 65 of a grapple fixture 20 affixed to a target object 14. The pole pieces are spaced by an air gap from the strike plate when the mechanism first contacts the grapple fixture. An individual control circuit and power source is provided for the pull-in coil and one holding coil of each electromagnet. A back-up control circuit connected to the two power sources and a third power source is provided for the remaining holding coils. When energized, the pull-in coils overcome the suspension system and air gap and are automatically de-energized when the pole pieces move to grapple and impose a preload force across the grapple interface. A battery back-up 89A,89B is a redundant power source for each electromagnet in each individual control circuit and is automatically connected upon failure of the primary power source. A centerline mounted camera 31 and video monitor 70 are used in cooperation with a target pattern 19 on the reflective surface 67 of the strike plate to effect targeting and alignment.

  2. A Framework for the Utilization of Information Technology in Higher Education Admission Department

    ERIC Educational Resources Information Center

    McClea, Michael; Yen, David C.

    2005-01-01

    Purpose: Through an examination of the admission department at Miami University of Ohio and their use of information technology, a generalized framework for the use of information technology in university admissions is proposed. Design/methodology/approach: The paper was developed to start an introduction to the admission process and the role of…

  3. A small animal holding fixture system with positional reproducibility for longitudinal multimodal imaging

    NASA Astrophysics Data System (ADS)

    Kokuryo, Daisuke; Kimura, Yuichi; Obata, Takayuki; Yamaya, Taiga; Kawamura, Kazunori; Zhang, Ming-Rong; Kanno, Iwao; Aoki, Ichio

    2010-07-01

    This study presents a combined small animal holding fixture system, termed a 'bridge capsule', which provides for small animal re-fixation with positional reproducibility. This system comprises separate holding fixtures for the head and lower body and a connecting part to a gas anesthesia system. A mouse is fixed in place by the combination of a head fixture with a movable part made from polyacetal resin, a lower body fixture made from vinyl-silicone and a holder for the legs and tail. For re-fixation, a similar posture could be maintained by the same holding fixtures and a constant distance between the head and lower body fixtures is maintained. Artifacts caused by the bridge capsule system were not observed on magnetic resonance (MRI) and positron emission tomography (PET) images. The average position differences of the spinal column and the iliac body before and after re-fixation for the same modality were approximately 1.1 mm. The difference between the MRI and PET images was approximately 1.8 mm for the lower body fixture after image registration using fiducial markers. This system would be useful for longitudinal, repeated and multimodal imaging experiments requiring similar animal postures.

  4. The Changing College Admissions Scene.

    ERIC Educational Resources Information Center

    Sjogren, Cliff

    1983-01-01

    Discusses the status of college admissions and some of the forces that influenced college admissions policies during each of four three-year periods: the Sputnik Era (1957-60), the Postwar Baby Boom Era (1964-67), the "New Groups" Era (1971-74), and the Stable Enrollment Era (1978-81). (PGD)

  5. Optimal Admission to Higher Education

    ERIC Educational Resources Information Center

    Albaek, Karsten

    2017-01-01

    This paper analyses admission decisions when students from different high school tracks apply for admission to university programmes. I derive a criterion that is optimal in the sense that it maximizes the graduation rates of the university programmes. The paper contains an empirical analysis that documents the relevance of theory and illustrates…

  6. Integrated calibration sphere and calibration step fixture for improved coordinate measurement machine calibration

    DOEpatents

    Clifford, Harry J [Los Alamos, NM

    2011-03-22

    A method and apparatus for mounting a calibration sphere to a calibration fixture for Coordinate Measurement Machine (CMM) calibration and qualification is described, decreasing the time required for such qualification, thus allowing the CMM to be used more productively. A number of embodiments are disclosed that allow for new and retrofit manufacture to perform as integrated calibration sphere and calibration fixture devices. This invention renders unnecessary the removal of a calibration sphere prior to CMM measurement of calibration features on calibration fixtures, thereby greatly reducing the time spent qualifying a CMM.

  7. EIGHTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W. L.

    2013-09-03

    A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. Seventy tests using mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they meet the criterion of leak-tightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. High temperature aging continues for 23 GLT O-ring fixtures at 200 – 270 ºF. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The remaining GLT O-ring fixtures aging at 300 ºF have been retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 61 - 85 months, which is still bounding to O-ring temperatures during storage in KArea Complex (KAC). Based on expectations that the fixtures aging at 200 ºF will remain leaktight for a significant period yet to come, 2 additional fixtures began aging in 2011 at an intermediate temperature of 270 ºF, with hopes that they may reach a failure condition before the 200 ºF fixtures. High temperature aging continues for 6 GLT-S O-ring fixtures at 200 – 300 ºF. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 ºF. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 - 300 ºF for 41 - 45 months. Aging and periodic leak testing will continue for the remaining PCV fixtures.

  8. 28 CFR 549.42 - Involuntary admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SERVICES Administrative Safeguards for Psychiatric Treatment and Medication § 549.42 Involuntary admission... voluntarily consent either to psychiatric admission or to medication, is subject to judicial...

  9. 32 CFR 242.5 - Admission procedures.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... HEALTH SCIENCES § 242.5 Admission procedures. (a) Application—(1) Civilians. Civilians seeking admission to the School of Medicine shall make direct application following instructions published in...

  10. Vision-Based Control of a Handheld Surgical Micromanipulator with Virtual Fixtures

    PubMed Central

    Becker, Brian C.; MacLachlan, Robert A.; Lobes, Louis A.; Hager, Gregory D.; Riviere, Cameron N.

    2012-01-01

    Performing micromanipulation and delicate operations in submillimeter workspaces is difficult because of destabilizing tremor and imprecise targeting. Accurate micromanipulation is especially important for microsurgical procedures, such as vitreoretinal surgery, to maximize successful outcomes and minimize collateral damage. Robotic aid combined with filtering techniques that suppress tremor frequency bands increases performance; however, if knowledge of the operator’s goals is available, virtual fixtures have been shown to further improve performance. In this paper, we derive a virtual fixture framework for active handheld micromanipulators that is based on high-bandwidth position measurements rather than forces applied to a robot handle. For applicability in surgical environments, the fixtures are generated in real-time from microscope video during the procedure. Additionally, we develop motion scaling behavior around virtual fixtures as a simple and direct extension to the proposed framework. We demonstrate that virtual fixtures significantly outperform tremor cancellation algorithms on a set of synthetic tracing tasks (p < 0.05). In more medically relevant experiments of vein tracing and membrane peeling in eye phantoms, virtual fixtures can significantly reduce both positioning error and forces applied to tissue (p < 0.05). PMID:24639624

  11. Vision-Based Control of a Handheld Surgical Micromanipulator with Virtual Fixtures.

    PubMed

    Becker, Brian C; Maclachlan, Robert A; Lobes, Louis A; Hager, Gregory D; Riviere, Cameron N

    2013-02-19

    Performing micromanipulation and delicate operations in submillimeter workspaces is difficult because of destabilizing tremor and imprecise targeting. Accurate micromanipulation is especially important for microsurgical procedures, such as vitreoretinal surgery, to maximize successful outcomes and minimize collateral damage. Robotic aid combined with filtering techniques that suppress tremor frequency bands increases performance; however, if knowledge of the operator's goals is available, virtual fixtures have been shown to further improve performance. In this paper, we derive a virtual fixture framework for active handheld micromanipulators that is based on high-bandwidth position measurements rather than forces applied to a robot handle. For applicability in surgical environments, the fixtures are generated in real-time from microscope video during the procedure. Additionally, we develop motion scaling behavior around virtual fixtures as a simple and direct extension to the proposed framework. We demonstrate that virtual fixtures significantly outperform tremor cancellation algorithms on a set of synthetic tracing tasks (p < 0.05). In more medically relevant experiments of vein tracing and membrane peeling in eye phantoms, virtual fixtures can significantly reduce both positioning error and forces applied to tissue (p < 0.05).

  12. NINTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W.

    2014-08-06

    A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. One approach has been to periodically evaluate the leak performance of O-rings being aged in mock-up 9975 Primary Containment Vessels (PCVs) at elevated temperatures. Other methods such as compression-stress relaxation (CSR) tests and field surveillance are also on-going to evaluate O-ring behavior. Seventy tests using PCV mock-ups were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they continue to meet the leak-tightness criterion defined in ANSI standard N14.5-97. Due to material substitution, fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. High temperature aging continues for 23 GLT O-ring fixtures at 200 – 270 ºF. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The earliest 300 °F GLT O-ring fixture failure was observed at 34 months. The remaining GLT O-ring fixtures aging at 300 ºF have been retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 72 - 96 months, which bounds O-ring temperatures anticipated during storage in K-Area Complex (KAC). Based on expectations that the 200 ºF fixtures will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging in 2011 at 270 ºF, with hopes that they may reach a failure condition before the 200 ºF fixtures, thus providing additional time to failure data. High temperature aging continues for 6 GLT-S O-ring fixtures at 200 – 300 ºF. Room temperature leak test failures have been experienced in all 8 of the

  13. SEVENTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W.

    2012-08-30

    A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. Seventy tests using mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they meet the criterion of leak-tightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. High temperature aging continues for 23 GLT O-ring fixtures at 200 – 270 ºF. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The remaining GLT O-ring fixtures aging at 300 ºF have been retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 54-72 months, which is still bounding to O-ring temperatures during storage in K-Area Complex (KAC). Based on expectations that the fixtures aging at 200 ºF will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging in 2011 at an intermediate temperature of 270 ºF, with hopes that they may reach a failure condition before the 200 ºF fixtures. High temperature aging continues for 6 GLT-S O-ring fixtures at 200 – 300 ºF. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 ºF. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 - 300 ºF for 30 - 36 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the O-rings displayed a compression set ranging from 51 – 96%. This is greater than seen to date for any packages inspected during KAC field

  14. 22 CFR 229.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Admission. 229.300 Section 229.300 Foreign... and Recruitment Prohibited § 229.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient to which §§...

  15. 22 CFR 229.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Admission. 229.300 Section 229.300 Foreign... and Recruitment Prohibited § 229.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient to which §§...

  16. 22 CFR 146.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Admission. 146.300 Section 146.300 Foreign... Recruitment Prohibited § 146.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient to which §§ 146.300...

  17. 10 CFR 1042.300 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 4 2013-01-01 2013-01-01 false Admission. 1042.300 Section 1042.300 Energy DEPARTMENT OF... Prohibited § 1042.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient to which §§ 1042.300 through...

  18. 44 CFR 68.9 - Admissible evidence.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Admissible evidence. 68.9 Section 68.9 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF... admissible. (b) Documentary and oral evidence shall be admissible. (c) Admissibility of non-expert...

  19. College Admissions Policies for the 1970's.

    ERIC Educational Resources Information Center

    College Entrance Examination Board, New York, NY.

    The papers included in this collection are (1) "Problems and Issues Confronting the Admissions Community" by Clyde Vroman; (2) "Frozen Assumptions in Admissions" by B. Alden Thresher; (3) "The Effect of Federal Programs on Admissions Policies" by John F. Morse; (4) "State Plans for Higher Education and Their Influence on Admissions" by Charles W.…

  20. 45 CFR 618.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 618.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by...

  1. Superior biofunctionality of dental implant fixtures uniformly coated with durable bioglass films by magnetron sputtering.

    PubMed

    Popa, A C; Stan, G E; Enculescu, M; Tanase, C; Tulyaganov, D U; Ferreira, J M F

    2015-11-01

    Bioactive glasses are currently considered the suitable candidates to stir the quest for a new generation of osseous implants with superior biological/functional performance. In congruence with this vision, this contribution aims to introduce a reliable technological recipe for coating fairly complex 3D-shaped implants (e.g. dental screws) with uniform and mechanical resistant bioactive glass films by the radio-frequency magnetron sputtering method. The mechanical reliability of the bioactive glass films applied to real Ti dental implant fixtures has been evaluated by a procedure comprised of "cold" implantation in pig mandibular bone from a dead animal, followed by immediate tension-free extraction tests. The effects of the complex mechanical strains occurring during implantation were analysed by scanning electron microscopy coupled with electron dispersive spectroscopy. Extensive biocompatibility assays (MTS, immunofluorescence, Western blot) revealed that the bioactive glass films stimulated strong cellular adhesion and proliferation of human dental pulp stem cells, without promoting their differentiation. The ability of the implant coatings to conserve a healthy stem cell pool is promising to further endorse the fabrication of new osseointegration implant designs with extended lifetime.

  2. SIXTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W.

    2011-08-31

    A series of experiments to monitor the aging performance of Viton{reg_sign} GLT O-rings used in the Model 9975 package has been ongoing for seven years at the Savannah River National Laboratory. Seventy tests using mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested periodically to determine if they meet the criterion of leak-tightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues for 33 GLT O-ring fixtures at 200-300 F. Room temperature leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 F and higher temperatures, and in 7 fixtures aging at 300 F. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 41-60 months, which is still bounding to O-ring temperatures during storage in K-Area Complex (KAC). Based on expectations that the fixtures aging at 200 F will remain leak-tight for a significant period yet to come, 2 additional fixtures began aging within the past year at an intermediate temperature of 270 F, with hopes that they may leak before the 200 F fixtures. High temperature aging continues for 6 GLT-S O-ring fixtures at 200-300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200-300 F for up to 26 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the Orings displayed a compression set ranging from 51-96%. This is greater than seen to date for packages inspected during KAC field surveillance (24% average). For GLT O-rings, separate service life estimates have been made based on the O-ring fixture leak test data and based on compression stress relaxation

  3. FIFTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W.; Hoffman, E.

    2011-04-11

    A series of experiments to monitor the aging performance of Viton{reg_sign} GLT O-rings used in the Model 9975 package has been ongoing for six years at the Savannah River National Laboratory. Sixty-seven mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested at nominal six month intervals to determine if they meet the criterion of leaktightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues for 36 GLT O-ring fixtures at 200-350 F. Room temperature leak test failures have been experienced in 6 of the GLT O-ring fixtures aging at 300 and 350 F, and in all 3 of the GLT O-ring fixtures aging at higher temperatures. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 30-48 months, which is still bounding to O-ring temperatures during storage in KAMS. High temperature aging continues for 6 GLT-S O-ring fixtures at 200-300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 or 300 F for 19 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the Orings displayed a compression set ranging from 51-95%. This is significantly greater than seen to date for packages inspected during KAMS field surveillance (23% average). For GLT O-rings, service life based on the room temperature leak rate criterion is comparable to that predicted by compression stress relaxation (CSR) data at higher temperatures (350-400 F). While there are no comparable failure data yet at aging temperatures below 300 F, extrapolations of the data for GLT O-rings suggests the CSR model predictions provide a conservative prediction of service

  4. FIFTH INTERIM STATUS REPORT: MODEL 9975 PCV O-RING FIXTURE LONG-TERM LEAK PERFORMANCE

    SciTech Connect

    Daugherty, W.; Hoffman, E.

    2010-11-01

    A series of experiments to monitor the aging performance of Viton{sup reg.} GLT O-rings used in the Model 9975 package has been ongoing for six years at the Savannah River National Laboratory. Sixty-seven mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested at nominal six month intervals to determine if they meet the criterion of leaktightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues for 36 GLT O-ring fixtures at 200--350 F. Room temperature leak test failures have been experienced in 5 of the GLT O-ring fixtures aging at 300 and 350 F, and in all 3 of the GLT O-ring fixtures aging at higher temperatures. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 30--48 months, which is still bounding to O-ring temperatures during storage in KAMS. High temperature aging continues for 6 GLT-S O-ring fixtures at 200--300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 or 300 F for 19 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the O-rings displayed a compression set ranging from 51--95%. This is significantly greater than seen to date for packages inspected during KAMS field surveillance (23% average). For GLT O-rings, service life based on the room temperature leak rate criterion is comparable to that predicted by compression stress relaxation (CSR) data at higher temperatures (350--400 F). While there are no comparable failure data yet at aging temperatures below 300 F, extrapolations of the data for GLT O-rings suggests that CSR model predictions provide a conservative prediction of

  5. Heat generated during seating of dental implant fixtures.

    PubMed

    Flanagan, Dennis

    2014-04-01

    Frictional heat can be generated during seating of dental implants into a drill-prepared osteotomy. This in vitro study tested the heat generated by implant seating in dense bovine mandible ramus. A thermocouple was placed approximately 0.5 mm from the rim of the osteotomy during seating of each dental implant. Four diameters of implants were tested. The average temperature increases were 0.075°C for the 5.7-mm-diameter implant, 0.97°C for the 4.7-mm-diameter implant, 1.4°C for the 3.7-mm-diameter implant, and 8.6°C for the 2.5-mm-diameter implant. The results showed that heat was indeed generated and a small temperature rise occurred, apparently by the friction of the implant surface against the fresh-cut bone surface. Bone is a poor thermal conductor. The titanium of the implant and the steel of the handpiece are much better heat conductors. Titanium may be 70 times more heat conductive than bone. The larger diameter and displacement implant may act as a heat sink to draw away any heat produced from the friction of seating the implant at the bone-implant interface. The peak temperature duration was momentary, and not measured, but this was approximately less than 1 second. Except for the 2.5-mm-diameter implants, the temperature rises and durations were found to be below those previously deemed to be detrimental, so no clinically significant osseous damage would be expected during dental implant fixture seating of standard and large-diameter-sized implants. A 2.5-mm implant may generate detrimental heat during seating in nonvital bone, but this may be clinically insignificant in vital bone. The surface area and thermal conductivity are important factors in removing generated heat transfer at the bone-implant interface. The F value as determined by analysis of variance was 69.22, and the P value was less than .0001, demonstrating significant differences between the groups considered as a whole.

  6. Admissible consensus for heterogeneous descriptor multi-agent systems

    NASA Astrophysics Data System (ADS)

    Yang, Xin-Rong; Liu, Guo-Ping

    2016-09-01

    This paper focuses on the admissible consensus problem for heterogeneous descriptor multi-agent systems. Based on algebra, graph and descriptor system theory, the necessary and sufficient conditions are proposed for heterogeneous descriptor multi-agent systems achieving admissible consensus. The provided conditions depend on not only the structure properties of each agent dynamics but also the topologies within the descriptor multi-agent systems. Moreover, an algorithm is given to design the novel consensus protocol. A numerical example demonstrates the effectiveness of the proposed design approach.

  7. 40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture... Applicability; description of the wood furniture and fixture production without water wash spray booth(s)...

  8. 40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture...; description of the wood furniture and fixture production with water wash spray booth(s) or with...

  9. 32 CFR 242.5 - Admission procedures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... HEALTH SCIENCES § 242.5 Admission procedures. (a) Application—(1) Civilians. Civilians seeking admission... conditionally select candidates to fill available class spaces. Those conditionally selected shall be the...

  10. System identification of the Large-Angle Magnetic Suspension Test Fixture (LAMSTF)

    NASA Technical Reports Server (NTRS)

    Huang, Jen-Kuang

    1994-01-01

    The Large-Angle Magnetic Suspension Test Fixture (LAMSTF), a laboratory-scale research project to demonstrate the magnetic suspension of objects over wide ranges of attitudes, has been developed. This system represents a scaled model of a planned Large-Gap Magnetic Suspension System (LGMSS). The LAMSTF consists of a small cylindrical permanent magnet suspended element which is levitated above a planar array of five electromagnets mounted in a circular configuration. The cylinder is a rigid body and can be controlled to move in five independent degrees of freedom. Six position variables are sensed indirectly by using infrared light-emitting diodes and light-receiving phototransistors. The motion of the suspended cylinder is in general nonlinear and hence only the linear, time-invariant perturbed motion about an equilibrium state is considered. One of the main challenges in this project is the control of the suspended element over a wide range of orientations. An accurate dynamic model plays an essential role in controller design. The analytical model is first derived and open-loop characteristics discussed. The system is shown to be highly unstable and requires feedback control for system identification. Projection filters are first proposed to identify the state space model from closed-loop input/output test data in the time domain. This method is then extended to identify linear systems from the frequency test data. A canonical transformation matrix is also derived to transform the identified state space model into the physical coordinate. The LAMSTF system is stabilized by using a linear quadratic regulator (LQR) feedback controller for closed-loop identification. The rate information is obtained by calculating the back difference of the sensed position signals. Only the closed-loop random input/output data are recorded. Preliminary results from numerical simulations demonstrate that the identified system model is fairly accurate from either time domain or

  11. 18 CFR 1317.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 2 2014-04-01 2014-04-01 false Admission. 1317.300 Section 1317.300 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1317.300 Admission. (a) General....

  12. 18 CFR 1317.300 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 2 2013-04-01 2012-04-01 true Admission. 1317.300 Section 1317.300 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1317.300 Admission. (a) General....

  13. 38 CFR 23.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Admission. 23.300 Section 23.300 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 23.300 Admission. (a) General....

  14. 18 CFR 1317.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 2 2012-04-01 2012-04-01 false Admission. 1317.300 Section 1317.300 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1317.300 Admission. (a) General....

  15. 36 CFR 1211.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false Admission. 1211.300 Section 1211.300 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION GENERAL RULES... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1211.300 Admission. (a) General....

  16. An Economic Model for Selective Admissions

    ERIC Educational Resources Information Center

    Haglund, Alma

    1978-01-01

    The author presents an economic model for selective admissions to postsecondary nursing programs. Primary determinants of the admissions model are employment needs, availability of educational resources, and personal resources (ability and learning potential). As there are more applicants than resources, selective admission practices are…

  17. 17 CFR 12.33 - Admissions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... REPARATIONS Discovery § 12.33 Admissions. (a) Request for admissions. Any party may, within the time permitted... truth of any matters set forth in the request that relate to statements or opinions of fact or of the...) Reply. Each matter of which an admission is requested shall be separately set forth. The matter...

  18. Admission to Medical Education in Ten Countries.

    ERIC Educational Resources Information Center

    Burn, Barbara B., Ed.

    As part of a study of access and admission to higher education in Germany and the United States, a group of papers on medical admissions in various countries was commissioned. The papers presented in this book reveal wide differences in admissions policies and procedures. Barbara Burn examines some of the major issues in a foreword: representation…

  19. The Journal of College Admission Ethics Series.

    ERIC Educational Resources Information Center

    Loveland, Elaina C., Ed.; Raynor, Joyce, Ed.

    This book is the first significant body of literature on ethics in college admission published by the National Association for College Admission Counseling. The series is a select compilation of articles on ethics published in the Journal of College Admission in 1998 and 1999. The book is a source of information for the beginning and experienced…

  20. Reducing admissions for people with diabetes.

    PubMed

    Allan, Belinda

    Reversing the rise in emergency hospital admissions is an NHS priority. These admissions impact on elective capacity and waiting times and are unsustainable. The risk of hospitalisation for people with diabetes is almost twice that for others. Commissioners need to address admissions associated with diabetes and new guidance offers best-practice solutions.

  1. The Role of Noncognitive Assessment in Admissions

    ERIC Educational Resources Information Center

    Hoerle, Heather

    2014-01-01

    Confident that understanding and employing new approaches to assessment is a top priority for admissions professionals, the Secondary School Admission Test Board (SSATB) recently launched a Think Tank on the Future of Admission Assessment, with a two-year timeline and a charge to educate its membership and inspire greater innovation in admissions…

  2. Merit and Competition in Selective College Admissions

    ERIC Educational Resources Information Center

    Killgore, Leslie

    2009-01-01

    Using interview data from 34 admissions officers at 17 elite colleges, this paper compares two perspectives shaping admissions policy. Admissions officers apply a "merit" perspective that relies on indicators of student academic and nonacademic achievement. They also employ a "competition" perspective that evaluates student characteristics…

  3. Toward a Sociology of Law School Admissions.

    ERIC Educational Resources Information Center

    Erlanger, Howard S.

    1984-01-01

    The law school admission process plays a major role in determining the social class origins and ethnic composition of the bar, and perhaps also the nonlegal skills lawyers will have. Research is incomplete; consideration of admission criteria, the composition and processes of admissions committees, and applicant self-selection is advisable. (MSE)

  4. 29 CFR 36.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 36.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or...

  5. 10 CFR 1042.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... ENERGY (GENERAL PROVISIONS) NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1042.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission,...

  6. 10 CFR 1042.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... ENERGY (GENERAL PROVISIONS) NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1042.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission,...

  7. 29 CFR 36.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 36.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or...

  8. 29 CFR 36.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 36.300 Admission. (a) General. No person shall, on the basis of sex, be denied admission, or...

  9. 7 CFR 501.2 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 6 2011-01-01 2011-01-01 false Admission. 501.2 Section 501.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON U.S. MEAT ANIMAL RESEARCH CENTER, CLAY CENTER, NEBRASKA § 501.2 Admission. Admission to...

  10. 7 CFR 501.2 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 6 2013-01-01 2013-01-01 false Admission. 501.2 Section 501.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON U.S. MEAT ANIMAL RESEARCH CENTER, CLAY CENTER, NEBRASKA § 501.2 Admission. Admission to...

  11. 7 CFR 501.2 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 6 2014-01-01 2014-01-01 false Admission. 501.2 Section 501.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON U.S. MEAT ANIMAL RESEARCH CENTER, CLAY CENTER, NEBRASKA § 501.2 Admission. Admission to...

  12. 7 CFR 501.2 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 6 2012-01-01 2012-01-01 false Admission. 501.2 Section 501.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON U.S. MEAT ANIMAL RESEARCH CENTER, CLAY CENTER, NEBRASKA § 501.2 Admission. Admission to...

  13. 7 CFR 501.2 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Admission. 501.2 Section 501.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON U.S. MEAT ANIMAL RESEARCH CENTER, CLAY CENTER, NEBRASKA § 501.2 Admission. Admission to...

  14. The Evolution of College Admission Requirements

    ERIC Educational Resources Information Center

    Beale, Andrew V.

    2012-01-01

    The development of college admissions requirements during the seventeenth and eighteenth centuries was basically the story of the admission policies and practices at Harvard College. Candidates for admission were examined on their ability to read and translate Latin and Greek, and a careful check was made of their character and background. With…

  15. Thermal element for maintaining minimum lamp wall temperature in fluorescent fixtures

    DOEpatents

    Siminovitch, M.J.

    1992-11-10

    In a lighting fixture including a lamp and a housing, an improvement is disclosed for maintaining a lamp envelope area at a cooler, reduced temperature relative to the enclosed housing ambient. The improvement comprises a thermal element in thermal communication with the housing extending to and springably urging thermal communication with a predetermined area of the lamp envelope surface. 12 figs.

  16. 24 CFR 3280.813 - Outdoor outlets, fixtures, air-conditioning equipment, etc.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...-conditioning equipment, etc. 3280.813 Section 3280.813 Housing and Urban Development Regulations Relating to... Electrical Systems § 3280.813 Outdoor outlets, fixtures, air-conditioning equipment, etc. (a) Outdoor.../or air conditioning equipment located outside the manufactured home, shall have permanently...

  17. Thermal element for maintaining minimum lamp wall temperature in fluorescent fixtures

    DOEpatents

    Siminovitch, Michael J.

    1992-01-01

    In a lighting fixture including a lamp and a housing, an improvement is disclosed for maintaining a lamp envelope area at a cooler, reduced temperature relative to the enclosed housing ambient. The improvement comprises a thermal element in thermal communication with the housing extending to and springably urging thermal communication with a predetermined area of the lamp envelope surface.

  18. 10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 3 2014-01-01 2014-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section... CONSUMER PRODUCTS AND COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.54 Metal halide lamp ballasts... are applicable to metal halide lamp ballasts; and (2) For each basic model of metal halide...

  19. 10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 3 2013-01-01 2013-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section... CONSUMER PRODUCTS AND COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.54 Metal halide lamp ballasts... are applicable to metal halide lamp ballasts; and (2) For each basic model of metal halide...

  20. 10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 3 2012-01-01 2012-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section... CONSUMER PRODUCTS AND COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.54 Metal halide lamp ballasts... are applicable to metal halide lamp ballasts; and (2) For each basic model of metal halide...

  1. Working with dental school admissions committees to enroll a more diverse student body.

    PubMed

    Wells, Anne; Brunson, David; Sinkford, Jeanne C; Valachovic, Richard W

    2011-05-01

    The American Dental Education Association's Admissions Committee Workshop (ADEA ACW) was designed to challenge dental school administrators and admissions committee members to review their current admissions practices and to explore ways to attract a more diverse student body. Presented at the invitation of dental schools, this half-day interactive workshop provides opportunities for a dental school's administrators, staff, and admissions committee members to learn about the value of diversity in the educational environment and how to implement holistic admissions practices that take into consideration the experiences, attributes, and metrics of candidates for admission. This report explores the rationale for the development of the ADEA ACW, discusses lessons learned from presentation of the workshop at more than twenty-seven U.S. dental schools, and tracks enrollment trends of underrepresented minority students in dental schools where the workshop has been presented.

  2. Equivalences between nonuniform exponential dichotomy and admissibility

    NASA Astrophysics Data System (ADS)

    Zhou, Linfeng; Lu, Kening; Zhang, Weinian

    2017-01-01

    Relationship between exponential dichotomies and admissibility of function classes is a significant problem for hyperbolic dynamical systems. It was proved that a nonuniform exponential dichotomy implies several admissible pairs of function classes and conversely some admissible pairs were found to imply a nonuniform exponential dichotomy. In this paper we find an appropriate admissible pair of classes of Lyapunov bounded functions which is equivalent to the existence of nonuniform exponential dichotomy on half-lines R± separately, on both half-lines R± simultaneously, and on the whole line R. Additionally, the maximal admissibility is proved in the case on both half-lines R± simultaneously.

  3. Theory-Based University Admissions Testing for a New Millennium

    ERIC Educational Resources Information Center

    Sternberg, Robert J.

    2004-01-01

    This article describes two projects based on Robert J. Sternberg's theory of successful intelligence and designed to provide theory-based testing for university admissions. The first, Rainbow Project, provided a supplementary test of analytical, practical, and creative skills to augment the SAT in predicting college performance. The Rainbow…

  4. College-Admissions Experts Differ on Value of Summer Employment

    ERIC Educational Resources Information Center

    Greifner, Laura

    2006-01-01

    When it comes to getting into college, admissions experts differ on the value of summer jobs compared with that of academic programs, unpaid internships, foreign travel, or other activities designed to look good on a college application. This article presents some views from these experts regarding the value of students' summer jobs. They believe,…

  5. Admissions-Yield and Persistence Analysis. AIR Forum Paper 1978.

    ERIC Educational Resources Information Center

    Ramist, Leonard

    Data from the college Board's Admissions Test Program (ATP) Summary Reports are used to analyze the student market attraction for ATP report designations, the application rate, the acceptance rate, the enrollment yield, and the dropout rate for 254 different student groups for 25l colleges. Student groups are defined in terms of their College…

  6. Institutional Admissions Policies in Higher Education: A Widening Participation Perspective

    ERIC Educational Resources Information Center

    Greenbank, Paul

    2006-01-01

    Purpose: This article analyses how higher education institutions (HEIs) have responded to government policy to increase the participation rates of students from lower social classes through their admissions policies. Design/methodology/approach: The article uses documentary evidence and interviews with institutional policy makers to examine HEI…

  7. Racial and Ethnic Preference in College Admissions. Brookings Policy Briefs.

    ERIC Educational Resources Information Center

    Kane, Thomas J.; Dickens, William T.

    This paper examines the use of racial and ethnic preferences in college admissions, focusing on the extent of their use and their impact on the careers of the intended beneficiaries in light of the California Civil Rights Initiative, which is designed to end such preferences. A study by Kane (1995) found that at the most selective four-year…

  8. The Effects of Extrinsic Rewards on Admissions Counselors' Performance

    ERIC Educational Resources Information Center

    Gardner-Engel, Miriam

    2010-01-01

    This study examines the best ways to motivate college admissions counselors. A review of literature revealed multiple perspectives on intrinsic and extrinsic as well as tangible and intangible rewards. Primary research was designed to examine the impact of tangible rewards and verbal reinforcements with a convenience sample of nine college…

  9. 15 CFR 8b.20 - Admission and recruitment.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... speaking skills, the test results accurately reflect the applicant's aptitude or achievement level of..., manual, or speaking skills (except where those skills are the factors that the test purports to measure); (ii) admissions tests that are designed for persons with impaired sensory, manual, or speaking...

  10. 15 CFR 8b.20 - Admission and recruitment.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... speaking skills, the test results accurately reflect the applicant's aptitude or achievement level of..., manual, or speaking skills (except where those skills are the factors that the test purports to measure); (ii) admissions tests that are designed for persons with impaired sensory, manual, or speaking...

  11. 15 CFR 8b.20 - Admission and recruitment.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... speaking skills, the test results accurately reflect the applicant's aptitude or achievement level of..., manual, or speaking skills (except where those skills are the factors that the test purports to measure); (ii) admissions tests that are designed for persons with impaired sensory, manual, or speaking...

  12. 15 CFR 8b.20 - Admission and recruitment.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... speaking skills, the test results accurately reflect the applicant's aptitude or achievement level of..., manual, or speaking skills (except where those skills are the factors that the test purports to measure); (ii) admissions tests that are designed for persons with impaired sensory, manual, or speaking...

  13. 15 CFR 8b.20 - Admission and recruitment.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... speaking skills, the test results accurately reflect the applicant's aptitude or achievement level of..., manual, or speaking skills (except where those skills are the factors that the test purports to measure); (ii) admissions tests that are designed for persons with impaired sensory, manual, or speaking...

  14. Exploration of nursing doctoral admissions and performance outcomes.

    PubMed

    Megginson, Lucy

    2011-09-01

    This research aims to identify current admission criteria and academic performance outcomes in nursing PhD programs. A descriptive exploratory design was used to survey all American Association of Colleges of Nursing PhD programs (N = 110) via a Web-mediated standardized survey; the response rate was 51% (n = 56). Conclusions indicate six diverse yet complementary admission criteria: graduate grade point average (GPA), Graduate Record Examinations ® scores, writing samples, letters of recommendation, interviews, and research match with faculty. Findings also indicated that admission criteria largely lack predictive validity testing in regard to academic performance outcomes and are deficient in internal reliability. Academic performance outcomes included comprehensive examination, ongoing minimum graduate GPA of 3.0, formal dissertation, time to degree attainment, degree attainment, time to candidacy, type of employment after graduation, and publications and grants as a student and at 5 years postgraduation.

  15. High Temperature Ultrasonic Probe and Pulse-Echo Probe Mounting Fixture for Testing and Blind Alignment on Steam Pipes

    NASA Technical Reports Server (NTRS)

    Bar-Cohen, Yoseph (Inventor); Badescu, Mircea (Inventor); Lih, Shyh-Shiuh (Inventor); Sherrit, Stewart (Inventor); Takano, Nobuyuki (Inventor); Ostlund, Patrick N. (Inventor); Lee, Hyeong Jae (Inventor); Bao, Xiaoqi (Inventor)

    2017-01-01

    A high temperature ultrasonic probe and a mounting fixture for attaching and aligning the probe to a steam pipe using blind alignment. The high temperature ultrasonic probe includes a piezoelectric transducer having a high temperature. The probe provides both transmitting and receiving functionality. The mounting fixture allows the high temperature ultrasonic probe to be accurately aligned to the bottom external surface of the steam pipe so that the presence of liquid water in the steam pipe can be monitored. The mounting fixture with a mounted high temperature ultrasonic probe are used to conduct health monitoring of steam pipes and to track the height of condensed water through the wall in real-time.

  16. Fixture for supporting and aligning a sample to be analyzed in an X-ray diffraction apparatus

    DOEpatents

    Green, Lanny A.; Heck, Jr., Joaquim L.

    1987-01-01

    A fixture is provided for supporting and aligning small samples of material on a goniometer for X-ray diffraction analysis. A sample-containing capillary is accurately positioned for rotation in the X-ray beam by selectively adjusting the fixture to position the capillary relative to the x and y axes thereof to prevent wobble and position the sample along the z axis or the axis of rotation. By employing the subject fixture relatively small samples of materials can be analyzed in an X-ray diffraction apparatus previously limited to the analysis of much larger samples.

  17. Fixture for supporting and aligning a sample to be analyzed in an x-ray diffraction apparatus

    DOEpatents

    Green, L.A.; Heck, J.L. Jr.

    1985-04-23

    A fixture is provided for supporting and aligning small samples of material on a goniometer for x-ray diffraction analysis. A sample-containing capillary is accurately positioned for rotation in the x-ray beam by selectively adjusting the fixture to position the capillary relative to the x and y axes thereof to prevent wobble and position the sample along the z axis or the axis of rotation. By employing the subject fixture relatively small samples of materials can be analyzed in an x-ray diffraction apparatus previously limited to the analysis of much larger samples.

  18. Interrogation cradle and insertable containment fixture for detecting birefringent microcrystals in bile

    DOEpatents

    Darrow, Chris; Seger, Tino

    2003-09-30

    A transparent flow channel fluidly communicates a fluid source and a collection reservoir. An interrogating light beam passes through a first polarizer having a first plane of polarization. The flow channel is orthogonal to the light beam. The light beam passes through a fluid sample as it flows through the flow channel, and is then filtered through a second polarizer having a second plane of polarization rotated 90.degree. from the first plane of polarization. An electronic photo-detector is aligned with the light beam, and signals the presence of birefringent microcrystals in the fluid sample by generating voltage pulses. A disposable containment fixture includes the flow channel and the collection reservoir. The fixture is adapted for removable insertion into an interrogation cradle that includes optical and data processing components. The cradle rigidly positions the centerline of the flow channel orthogonal to the light beam.

  19. Seasonality of hospital admissions for mental disorders in Hanoi, Vietnam

    PubMed Central

    Trang, Phan Minh; Rocklöv, Joacim; Giang, Kim Bao; Nilsson, Maria

    2016-01-01

    Background Some studies have shown a relationship between seasonality in weather patterns and depressive and behavioural disorders, especially in temperate climate regions. However, there is a lack of studies describing the seasonal patterns of hospital admissions for a variety of mental disorders in tropical and subtropical nations. The aim of this study has been to examine the relationship between seasons and daily hospital admissions for mental disorders in Hanoi, Vietnam. Designs A 5-year database (2008–2012) compiled by Hanoi Mental Hospital covering mental disorder admissions diagnosed by the International Classification of Diseases 10 was analysed. A negative binominal regression model was applied to estimate the associations between seasonality and daily hospital admissions for mental disorders, for all causes and for specific diagnoses. Results The summer season indicated the highest relative risk (RR=1.24, confidence interval (CI)=1.1–1.39) of hospital admission for mental disorders, with a peak in these cases in June (RR=1.46, CI=1.19–1.7). Compared to other demographic groups, males and the elderly (aged over 60 years) were more sensitive to seasonal risk changes. In the summer season, the RR of hospital visits among men increased by 26% (RR=1.26, CI=1.12–1.41) and among the elderly by 23% (RR=1.23, CI=1.03–1.48). Furthermore, when temperatures including minimum, mean, and maximum increased 1°C, the number of cases for mental disorders increased by 1.7%, 2%, and 2.1%, respectively. Conclusion The study results showed a correlation between hospital admission for mental disorders and season. PMID:27566716

  20. 45 CFR 2555.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 4 2014-10-01 2014-10-01 false Admission. 2555.300 Section 2555.300 Public... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 2555.300 Admission. (a) General. No..., by any recipient to which §§ 2555.300 through 2555.310 apply, except as provided in §§ 2555.225...

  1. 6 CFR 17.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 6 Domestic Security 1 2012-01-01 2012-01-01 false Admission. 17.300 Section 17.300 Domestic... in Admission and Recruitment Prohibited § 17.300 Admission. (a) General. No person shall, on the... which §§ 17.300 through 17.310 apply, except as provided in §§ 17.225 and 17.230. (b)...

  2. 40 CFR 5.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Admission. 5.300 Section 5.300... in Admission and Recruitment Prohibited § 5.300 Admission. (a) General. No person shall, on the basis... which §§ 5.300 through §§ 5.310 apply, except as provided in §§ 5.225 and 5.230. (b)...

  3. 15 CFR 8a.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Admission. 8a.300 Section 8a.300... in Admission and Recruitment Prohibited § 8a.300 Admission. (a) General. No person shall, on the... which §§ 8a.300 through §§ 8a.310 apply, except as provided in §§ 8a.225 and §§ 8a.230. (b)...

  4. 45 CFR 2555.300 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 4 2011-10-01 2011-10-01 false Admission. 2555.300 Section 2555.300 Public... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 2555.300 Admission. (a) General. No..., by any recipient to which §§ 2555.300 through 2555.310 apply, except as provided in §§ 2555.225...

  5. 14 CFR 1253.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 5 2012-01-01 2012-01-01 false Admission. 1253.300 Section 1253.300... in Admission and Recruitment Prohibited § 1253.300 Admission. (a) General. No person shall, on the... which §§ 1253.300 through §§ 1253.310 apply, except as provided in §§ 1253.225 and §§ 1253.230....

  6. A Power Data Grapple Fixture gets a fit check in the SSPF

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Workers perform a fit check on a Power Data Grapple Fixture (PDGF) in the Space Station Processing Facility. The PDGF is part of the payload on mission STS-98, a flight to the International Space Station. During the mission, the crew will install the U.S. Lab in the Space Station during a series of three space walks. The STS-98 mission will provide the station with science research facilities and expand its power, life support and control capabilities.

  7. Temporal variation in major trauma admissions

    PubMed Central

    Kieffer, WKM; Michalik, DV; Gallagher, K; McFadyen, I; Bernard, J; Rogers, BA

    2016-01-01

    Introduction Trauma is a significant cause of morbidity and mortality in the UK. Since the inception of the trauma networks, little is known of the temporal pattern of trauma admissions. Methods Trauma Audit and Research Network data for 1 April 2011 to 31 March 2013 were collated from two large major trauma centres (MTCs) in the South East of England: Brighton and Sussex University Hospitals NHS Trust (BSUH) and St George's University Hospitals NHS Foundation Trust (SGU). The number of admissions and the injury severity score by time of admission, by weekdays versus weekend and by month/season were analysed. Results There were 1,223 admissions at BSUH and 1,241 at SGU. There was significant variation by time of admission; there were more admissions in the afternoons (BSUH p<0.001) and evenings (SGU p<0.001). There were proportionally more admissions at the weekends than on weekdays (BSUH p<0.001, SGU p=0.028). There was significant seasonal variation in admissions at BSUH (p<0.001) with more admissions in summer and autumn. No significant seasonal variation was observed at SGU (p=0.543). Conclusions The temporal patterns observed were different for each MTC with important implications for resource planning of trauma care. This study identified differing needs for different MTCs and resource planning should be individualised to the network. PMID:26741676

  8. Linear friction weld process monitoring of fixture cassette deformations using empirical mode decomposition

    NASA Astrophysics Data System (ADS)

    Bakker, O. J.; Gibson, C.; Wilson, P.; Lohse, N.; Popov, A. A.

    2015-10-01

    Due to its inherent advantages, linear friction welding is a solid-state joining process of increasing importance to the aerospace, automotive, medical and power generation equipment industries. Tangential oscillations and forge stroke during the burn-off phase of the joining process introduce essential dynamic forces, which can also be detrimental to the welding process. Since burn-off is a critical phase in the manufacturing stage, process monitoring is fundamental for quality and stability control purposes. This study aims to improve workholding stability through the analysis of fixture cassette deformations. Methods and procedures for process monitoring are developed and implemented in a fail-or-pass assessment system for fixture cassette deformations during the burn-off phase. Additionally, the de-noised signals are compared to results from previous production runs. The observed deformations as a consequence of the forces acting on the fixture cassette are measured directly during the welding process. Data on the linear friction-welding machine are acquired and de-noised using empirical mode decomposition, before the burn-off phase is extracted. This approach enables a direct, objective comparison of the signal features with trends from previous successful welds. The capacity of the whole process monitoring system is validated and demonstrated through the analysis of a large number of signals obtained from welding experiments.

  9. Characterization and Comparison of Vibration Transfer Paths in a Helicopter Gearbox and a Fixture Mounted Gearbox

    NASA Technical Reports Server (NTRS)

    Islam, Akm Anwarul; Dempsey, Paula J.; Feldman, Jason; Larsen, Chris

    2014-01-01

    Health monitoring of rotorcraft components, currently being performed by Health and Usage Monitoring Systems through analyses of vibration signatures of dynamic mechanical components, is very important for their safe and economic operation. HUMS analyze vibration signatures associated with faults and quantify them as condition indicators to predict component behavior. Vibration transfer paths are characterized by frequency response functions derived from the input/output relationship between applied force and dynamic response through a structure as a function of frequency. With an objective to investigate the differences in transfer paths, transfer path measurements were recorded under similar conditions in the left and right nose gearboxes of an AH-64 helicopter and in an isolated left nose gearbox in a test fixture at NASA Glenn Research Center. The test fixture enabled the application of measured torques-common during an actual operation. An impact hammer as well as commercial and lab piezo shakers, were used in conjunction with two types of commercially available accelerometers to collect the vibration response under various test conditions. The frequency response functions measured under comparable conditions of both systems were found to be consistent. Measurements made on the fixture indicated certain real-world installation and maintenance issues, such as sensor alignments, accelerometer locations and installation torques, had minimal effect. However, gear vibration transfer path dynamics appeared to be somewhat dependent on the presence of oil, and the transfer path dynamics were notably different if the force input was on the internal ring gear rather than on the external gearbox case.

  10. A Single-Block TRL Test Fixture for the Cryogenic Characterization of Planar Microwave Components

    NASA Technical Reports Server (NTRS)

    Mejia, M.; Creason, A. S.; Toncich, S. S.; Ebihara, B. T.; Miranda, F. A.

    1996-01-01

    The High-Temperature-Superconductivity (HTS) group of the RF Technology Branch, Space Electronics Division, is actively involved in the fabrication and cryogenic characterization of planar microwave components for space applications. This process requires fast, reliable, and accurate measurement techniques not readily available. A new calibration standard/test fixture that enhances the integrity and reliability of the component characterization process has been developed. The fixture consists of 50 omega thru, reflect, delay, and device under test gold lines etched onto a 254 microns (0.010 in) thick alumina substrate. The Thru-Reflect-Line (TRL) fixture was tested at room temperature using a 30 omega, 7.62 mm (300 mil) long, gold line as a known standard. Good agreement between the experimental data and the data modelled using Sonnet's em(C) software was obtained for both the return (S(sub 11)) and insertion (S( 21)) losses. A gold two-pole bandpass filter with a 7.3 GHz center frequency was used as our Device Under Test (DUT), and the results compared with those obtained using a Short-Open-Load-Thru (SOLT) calibration technique.

  11. A Study of the Conservatism of Resonant Shock Test Fixtures

    SciTech Connect

    Cap, J.S.

    1998-12-03

    Portions of a series of end-of-life tests are described for a Sandia National Li~boratories- designed space-based sensor that utilizes a mercury-cadmium-telluride focal plane array. Variations in background intensity are consistent with the hypothesis that seasonal variations in solar position cause changes in the pattern of shadows falling across the compartment containing the optical elements, filter-band components, and focal plane array. When the sensor compartment is most fully illuminated by the sun, background intensities are large and their standard deviations tend to be large. During the winter season, when the compartment is most fully shadowed by surrounding structure, backgrounci intensities are small and standard deviations tend to be small. Details in the surrounding structure are speculated to produce transient shadows that complicate background intensifies as a function of time or of sensor position in orbit. KEYwoRDs Noise measurements, background intensity, focal plane array, mercury-cadmium-telluride.

  12. 28 CFR 54.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 54.300 Admission. (a) General. No person shall, on the basis of sex, be...

  13. 14 CFR 1253.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex... basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient...

  14. 7 CFR 15a.21 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 1 2014-01-01 2014-01-01 false Admission. 15a.21 Section 15a.21 Agriculture Office of the Secretary of Agriculture EDUCATION PROGRAMS OR ACTIVITIES RECEIVING OR BENEFITTING FROM FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited §...

  15. 7 CFR 15a.21 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 1 2011-01-01 2011-01-01 false Admission. 15a.21 Section 15a.21 Agriculture Office of the Secretary of Agriculture EDUCATION PROGRAMS OR ACTIVITIES RECEIVING OR BENEFITTING FROM FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited §...

  16. 45 CFR 618.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on... shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by...

  17. 45 CFR 618.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on... shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by...

  18. 45 CFR 618.300 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on... shall, on the basis of sex, be denied admission, or be subjected to discrimination in admission, by...

  19. 7 CFR 503.2 - Admission.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 6 2011-01-01 2011-01-01 false Admission. 503.2 Section 503.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON PLUM ISLAND ANIMAL DISEASE CENTER § 503.2 Admission. No person will be admitted to PIADC,...

  20. 7 CFR 503.2 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 6 2013-01-01 2013-01-01 false Admission. 503.2 Section 503.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON PLUM ISLAND ANIMAL DISEASE CENTER § 503.2 Admission. No person will be admitted to PIADC,...

  1. 7 CFR 503.2 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Admission. 503.2 Section 503.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON PLUM ISLAND ANIMAL DISEASE CENTER § 503.2 Admission. No person will be admitted to PIADC,...

  2. 7 CFR 503.2 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 6 2014-01-01 2014-01-01 false Admission. 503.2 Section 503.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON PLUM ISLAND ANIMAL DISEASE CENTER § 503.2 Admission. No person will be admitted to PIADC,...

  3. Unethical Admissions: Academic Integrity in Question.

    PubMed

    Ansah, Richard Hannis; Aikhuele, Daniel O; Yao, Liu

    2016-11-28

    The increasing unethical practices of graduates' admissions have heightened concerns about the integrity of the academy. This article informs this important subject that affects the students, admission systems, and the entire scientific community, thus, representing an approach against scholarly black market activities including falsified documents and unethical practices by consultants and students' recruitment agencies.

  4. 7 CFR 503.2 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 6 2012-01-01 2012-01-01 false Admission. 503.2 Section 503.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE CONDUCT ON PLUM ISLAND ANIMAL DISEASE CENTER § 503.2 Admission. No person will be admitted to PIADC,...

  5. Profile in Action: Linking Admission and Retention

    ERIC Educational Resources Information Center

    Cortes, Carla M.

    2013-01-01

    A profile-oriented retention strategy embraces the admission process as a powerful lever in improving retention and completion rates and recognizes that the student profile can be shaped by changes in admission policies or priorities--even within the current market position of the institution. In addition, the student body can be oriented toward…

  6. Alphabetical Order Effects in School Admissions

    ERIC Educational Resources Information Center

    Jurajda, Štepán; Münich, Daniel

    2016-01-01

    If school admission committees use alphabetically sorted lists of applicants in their evaluations, one's position in the alphabet according to last name initial may be important in determining access to selective schools. Jurajda and Münich (2010) "Admission to Selective Schools, Alphabetically". "Economics of Education…

  7. Why Do We Stay in Admissions?

    ERIC Educational Resources Information Center

    Piersol, Marion Kandel; And Others

    1993-01-01

    Admission counselors (n=200) completed surveys about employment, title, on-the-job training, travel, and availability and satisfaction with certain responsibilities. Most satisfying admission responsibilities were program organization and implementation, applicant review and decision, and formal presentations. Least satisfying were telemarketing,…

  8. An Admissions Race that's Already Won

    ERIC Educational Resources Information Center

    Stevens, Mitchell L.

    2008-01-01

    The author recently spent a year and a half in the admissions office of a highly selective Eastern college as an ethnographer, seeking to understand just how admissions officers make their decisions. He accompanied them on recruitment trips to high schools and college fairs, helped manage their offices' relentless current of visitors and mail, and…

  9. College Admission Professionals: Who Are We Now?

    ERIC Educational Resources Information Center

    Rapelye, Janet Lavin

    1999-01-01

    Reflects on roles that admission professionals hold within the academic community. Explains that admission professionals are educators and business managers; bring in revenue; and serve as advisors to the president, as spokespeople to alumni/ae, and if fortunate, as counselors to students. Suggests that counselors focus on students because they…

  10. 49 CFR 25.300 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Office of the Secretary of Transportation NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 25.300 Admission. (a) General. No person shall, on the basis of sex, be...

  11. 40 CFR 5.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex... of sex, be denied admission, or be subjected to discrimination in admission, by any recipient...

  12. 45 CFR 86.21 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex... of sex, be denied admission, or be subjected to discrimination in admission, by any recipient...

  13. 22 CFR 146.300 - Admission.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Relations DEPARTMENT OF STATE CIVIL RIGHTS NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 146.300 Admission. (a) General. No person shall, on the basis of sex, be...

  14. 28 CFR 54.300 - Admission.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 54.300 Admission. (a) General. No person shall, on the basis of sex, be...

  15. 43 CFR 41.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Lands: Interior Office of the Secretary of the Interior NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex... basis of sex, be denied admission, or be subjected to discrimination in admission, by any recipient...

  16. 45 CFR 86.21 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex... of sex, be denied admission, or be subjected to discrimination in admission, by any recipient...

  17. Admission to Law School: New Measures

    ERIC Educational Resources Information Center

    Shultz, Marjorie M.; Zedeck, Sheldon

    2012-01-01

    Standardized tests have been increasingly controversial over recent years in high-stakes admission decisions. Their role in operationalizing definitions of merit and qualification is especially contested, but in law schools this challenge has become particularly intense. Law schools have relied on the Law School Admission Test (LSAT) and an INDEX…

  18. Pediatric Type 1 Diabetes: Reducing Admission Rates for Diabetes Ketoacidosis

    PubMed Central

    Choi, Steven; Rinke, Michael L.; Vandervoot, Kathy; Heptulla, Rubina A.

    2016-01-01

    Background: Diabetes ketoacidosis (DKA) is a life-threatening complication of type 1 diabetes mellitus (T1DM). Reducing DKA admissions in children with T1DM requires a coordinated, comprehensive management plan. We aimed to decrease DKA admissions, 30-day readmissions, and length of stay (LOS) for DKA admissions. Methods: A multipronged intervention was designed in 2011 to reach all patients: (1) increase insulin pump use and basal-bolus regimen versus sliding scales, (2) transform educational program, (3) increased access to medical providers, and (4) support for patients and families. A before-after study was conducted comparing performance outcomes in years 2007-2010 (preintervention) to 2012-2014 (postintervention) using administrative data and Wilcoxon rank sum and Fischer exact tests. Results: DKA admissions decreased by 44% postintervention (16.7 vs 9.3 per 100 followed patient-years; P = .006), unique patient 30-day readmissions decreased from 20% to 5% postintervention (P = .001), and median LOS significantly decreased postintervention (P < .0001). Although not an original goal of the study, median hemoglobin A1C of a subset of the population transitioned from sliding scale decreased, 10.3% to 8.9% (P < .02). Conclusions: When clinical and widespread program interventions were used, significant reductions in DKA hospitalizations, 30-day readmissions, and LOS occurred for pediatric T1DM. Continuous performance improvement efforts are needed for improving DKA outcomes. PMID:27749721

  19. Predictive model of length of stay and discharge destination in neuroscience admissions

    PubMed Central

    Stecker, M. M.; Stecker, M.; Falotico, J.

    2017-01-01

    Background: The purpose of this study was to try and determine the best predictors of hospital length of stay and discharge destination in patients admitted to a neuroscience service. Methods: Valid data was collected for 170 patients. Variables included age, gender, location prior to admission, principle diagnosis, various physiological measurements upon admission, comorbidity, independence in various activities of daily living prior to admission, length of stay, and disposition upon discharge. Study design was a correlational descriptive study performed through the analysis of data and the development and validation of statistically significant factors in determining the length of stay. Results: All factors with a strong (P < 0.05) relationship with the length of stay were entered into a forward stepwise linear regression with length of stay as the dependent variable. The three most significant variables in predicting length of stay in this study were admission from an outpatient setting, modified Rankin score on admission, and systolic blood pressure on admission. Conclusions: Functional status at admission, specifically, a higher modified Rankin score and a lower systolic blood pressure along with the acquisition of deep vein thrombosis, catheter associated urinary tract infections, intubation, and admission to an intensive care unit all have a statistically significant effect on the hospital length of stay. PMID:28217396

  20. Practical aspects of complex permittivity reconstruction with neural-network-controlled FDTD modeling of a two-port fixture.

    PubMed

    Eves, E Eugene; Murphy, Ethan K; Yakovlev, Vadim V

    2007-01-01

    The paper discusses characteristics of a new modeling-based technique for determining dielectric properties of materials. Complex permittivity is found with an optimization algorithm designed to match complex S-parameters obtained from measurements and from 3D FDTD simulation. The method is developed on a two-port (waveguide-type) fixture and deals with complex reflection and transmission characteristics at the frequency of interest. A computational part is constructed as an inverse-RBF-network-based procedure that reconstructs dielectric constant and the loss factor of the sample from the FDTD modeling data sets and the measured reflection and transmission coefficients. As such, it is applicable to samples and cavities of arbitrary configurations provided that the geometry of the experimental setup is adequately represented by the FDTD model. The practical implementation of the method considered in this paper is a section of a WR975 waveguide containing a sample of a liquid in a cylindrical cutout of a rectangular Teflon cup. The method is run in two stages and employs two databases--first, built for a sparse grid on the complex permittivity plane, in order to locate a domain with an anticipated solution and, second, made as a denser grid covering the determined domain, for finding an exact location of the complex permittivity point. Numerical tests demonstrate that the computational part of the method is highly accurate even when the modeling data is represented by relatively small data sets. When working with reflection and transmission coefficients measured in an actual experimental fixture and reconstructing a low dielectric constant and the loss factor the technique may be less accurate. It is shown that the employed neural network is capable of finding complex permittivity of the sample when experimental data on the reflection and transmission coefficients are numerically dispersive (noise-contaminated). A special modeling test is proposed for validating the

  1. Advanced Computational Techniques for Power Tube Design.

    DTIC Science & Technology

    1986-07-01

    fixturing applications, in addition to the existing computer-aided engineering capabilities. o Helix TWT Manufacturing has Implemented a tooling and fixturing...illustrates the ajor features of this computer network. ) The backbone of our system is a Sytek Broadband Network (LAN) which Interconnects terminals and...automatic network analyzer (FANA) which electrically characterizes the slow-wave helices of traveling-wave tubes ( TWTs ) -- both for engineering design

  2. Reducing hospital admissions from nursing homes: a systematic review

    PubMed Central

    2014-01-01

    Background The geriatric nursing home population is vulnerable to acute and deteriorating illness due to advanced age, multiple chronic illnesses and high levels of dependency. Although the detriments of hospitalising the frail and old are widely recognised, hospital admissions from nursing homes remain common. Little is known about what alternatives exist to prevent and reduce hospital admissions from this setting. The objective of this study, therefore, is to summarise the effects of interventions to reduce acute hospitalisations from nursing homes. Methods A systematic literature search was performed in Cochrane Library, PubMed, MEDLINE, EMBASE and ISI Web of Science in April 2013. Studies were eligible if they had a geriatric nursing home study population and were evaluating any type of intervention aiming at reducing acute hospital admission. Systematic reviews, randomised controlled trials, quasi randomised controlled trials, controlled before-after studies and interrupted time series were eligible study designs. The process of selecting studies, assessing them, extracting data and grading the total evidence was done by two researchers individually, with any disagreement solved by a third. We made use of meta-analyses from included systematic reviews, the remaining synthesis is descriptive. Based on the type of intervention, the included studies were categorised in: 1) Interventions to structure and standardise clinical practice, 2) Geriatric specialist services and 3) Influenza vaccination. Results Five systematic reviews and five primary studies were included, evaluating a total of 11 different interventions. Fewer hospital admissions were found in four out of seven evaluations of structuring and standardising clinical practice; in both evaluations of geriatric specialist services, and in influenza vaccination of residents. The quality of the evidence for all comparisons was of low or very low quality, using the GRADE approach. Conclusions Overall, eleven

  3. Evaluation of Waste Heat Recovery and Utilization from Residential Appliances and Fixtures

    SciTech Connect

    Tomlinson, John J; Christian, Jeff; Gehl, Anthony C

    2012-09-01

    Executive Summary In every home irrespective of its size, location, age, or efficiency, heat in the form of drainwater or dryer exhaust is wasted. Although from a waste stream, this energy has the potential for being captured, possibly stored, and then reused for preheating hot water or air thereby saving operating costs to the homeowner. In applications such as a shower and possibly a dryer, waste heat is produced at the same time as energy is used, so that a heat exchanger to capture the waste energy and return it to the supply is all that is needed. In other applications such as capturing the energy in drainwater from a tub, dishwasher, or washing machine, the availability of waste heat might not coincide with an immediate use for energy, and consequently a heat exchanger system with heat storage capacity (i.e. a regenerator) would be necessary. This study describes a two-house experimental evaluation of a system designed to capture waste heat from the shower, dishwasher clothes washer and dryer, and to use this waste heat to offset some of the hot water energy needs of the house. Although each house was unoccupied, they were fitted with equipment that would completely simulate the heat loads and behavior of human occupants including operating the appliances and fixtures on a demand schedule identical to Building American protocol (Hendron, 2009). The heat recovery system combined (1) a gravity-film heat exchanger (GFX) installed in a vertical section of drainline, (2) a heat exchanger for capturing dryer exhaust heat, (3) a preheat tank for storing the captured heat, and (4) a small recirculation pump and controls, so that the system could be operated anytime that waste heat from the shower, dishwasher, clothes washer and dryer, and in any combination was produced. The study found capturing energy from the dishwasher and clothes washer to be a challenge since those two appliances dump waste water over a short time interval. Controls based on the status of the

  4. Lunar phases and psychiatric hospital admissions.

    PubMed

    Gorvin, J J; Roberts, M S

    1994-12-01

    To assess the lunar hypothesis as predictive of mental health emergencies and antisocial behavior, the relation of the lunar hypothesis and the occurrence of psychiatric hospital admissions of developmentally disabled adults was examined. The full moon phase of the lunar cycle did not explain a higher rate of hospital admission and accounted for only .007% of the variance. A critique of the methodology in prior research led to the suggestion that more immediate stressors and environmental factors are more plausible contributing factors to hospital admission.

  5. Advanced development of the spectrum sciences Model 5005-TF, single-event test fixture

    SciTech Connect

    Ackermann, M.R.; Browning, J.S. ); Hughlock, B.W. ); Lum, G.K. ); Tsacoyeanes, W.C. Lab., Inc., Cambridge, MA ); Weeks, M.D. )

    1990-09-01

    This report summarizes the advanced development of the Spectrum Sciences Model 5005-TF, Single-Event Test Fixture. The Model 5005-TF uses a Californium-252 (Cf-252) fission-fragment source to test integrated circuits and other devices for the effects of single-event phenomena. Particle identification methods commonly used in high-energy physics research and nuclear engineering have been incorporated into the Model 5005-TF for estimating the particle charge, mass, and energy parameters. All single-event phenomena observed in a device under test (DUT) are correlated with an identified fission fragment, and its linear energy transfer (LET) and range in the semiconductor material of the DUT.

  6. A Power Data Grapple Fixture gets a fit check in the SSPF

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Workers replace a panel on hardware in the Space Station Processing Facility, checking the fit of a Power Data Grapple Fixture (PDGF). The PDGF is part of the payload on mission STS- 98, a flight to the International Space Station. During the mission, the crew will install the U.S. Lab in the Space Station during a series of three space walks. The STS-98 mission will provide the station with science research facilities and expand its power, life support and control capabilities.

  7. Free-Roller Versus Fixed-Roller Fixtures in Flexure Testing of Advanced Ceramic Materials

    NASA Technical Reports Server (NTRS)

    Salem, Jonathan A.; Choi, Sung R.

    1996-01-01

    The error associated with strength measurements made with fixed-roller and V-grooved roller figures was studied with a variety of roller and figure material combinations. Both the fixed-roller and the V-grooved fixtures yielded an error in stress of about 4 to 7%. They also exhibited an appreciable amount of load strain hysteresis. Dynamic fatigue testing of 96 wt.% alumina verified the error: the fatigue strength was overestimated by 7 to 9% for the fixed roller configuration. The source of error is exclusively attributed to friction between the rollers and the specimen surface, as verified by previous investigators.

  8. 43 CFR 4.1141 - Admissions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... directed serves on the requesting party— (1) A sworn statement denying specifically the relevant matters of which an admission is requested; (2) A sworn statement setting forth in detail the reasons why he...

  9. 43 CFR 4.1141 - Admissions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... directed serves on the requesting party— (1) A sworn statement denying specifically the relevant matters of which an admission is requested; (2) A sworn statement setting forth in detail the reasons why he...

  10. 43 CFR 4.1141 - Admissions.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... directed serves on the requesting party— (1) A sworn statement denying specifically the relevant matters of which an admission is requested; (2) A sworn statement setting forth in detail the reasons why he...

  11. Marketing in Admissions: The Information System Approach.

    ERIC Educational Resources Information Center

    Wofford, O. Douglas; Timmerman, Ed

    1982-01-01

    A marketing information system approach for college admissions is outlined that includes objectives, information needs and sources, a data collection format, and information evaluation. Coordination with other institutional information systems is recommended. (MSE)

  12. The Parent Role in College Admission.

    ERIC Educational Resources Information Center

    Krugman, Mary K.

    1990-01-01

    Discusses techniques secondary school counselors can use to help parents understand and negotiate the college admissions process, including encouraging parental self-assessment; assisting parents to assess student; giving parents special tips; and maintaining open and ethical communication. (ABL)

  13. 28 CFR 549.42 - Involuntary admission.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SERVICES Administrative Safeguards for Psychiatric Treatment and Medication § 549.42 Involuntary admission. A court determination is necessary for involuntary hospitalization for psychiatric treatment. A sentenced inmate, not currently committed for psychiatric treatment, who is not able or willing...

  14. The Campus Visit Experience: Improving Student Recruitment at the University of Rhode Island. Report of the Admissions Advisory Committee

    ERIC Educational Resources Information Center

    Online Submission, 2011

    2011-01-01

    The purpose of this report was to identify best practices in the design of college and university admissions facilities with the goal of enhancing recruitment and yield of prospective students. The Admissions Advisory Committee at the University of Rhode Island conducted a literature review examining the importance of the campus visit experience…

  15. A Theory of How External Incentives Affect, and Are Affected by, Computer-aided Admissible Probability Testing.

    ERIC Educational Resources Information Center

    Brown, T. A.

    Admissible probability testing is a way of administering multiple choice tests in which a student states his subjective probability that each alternative answer is correct. His response is then scored by an admissible scoring system designed so that the student will perceive that is is in his interest to report his true subjective probability.…

  16. Fixtureless geometric inspection of nonrigid parts using "generalized numerical inspection fixture"

    NASA Astrophysics Data System (ADS)

    Radvar Esfahlan, Hassan

    Free-form nonrigid parts form the substance of today's automotive and aerospace industries. These parts have different shapes in free state due to their dimensional and geometric variations, gravity and residual strains. For the geometric inspection of such compliant parts, special inspection fixtures, in combination with coordinate measuring systems (CMM) and/or optical data acquisition devices (scanners) are used. This inevitably causes additional costs and delays that result in a lack of competitiveness in the industry. The goal of this thesis is to facilitate the dimensional and geometrical inspection of flexible components from a point cloud without using a jig or secondary conformation operation. More specifically, we aim to develop a methodology to localize and quantify the profile defects in the case of thin shells which are typical to the aerospace and automotive industries. The presented methodology is based on the fact that the interpoint geodesic distance between any two points of a shape remains unchangeable during an isometric deformation. This study elaborates on the theory and general methods for the metrology of nonrigid parts. We have developed a Generalized Numerical Inspection Fixture (GNIF), a robust methodology which merges existing technologies in metric and computational geometry, nonlinear dimensionality reduction techniques, and finite element methods to introduce a general approach to the fixtureless geometrical inspection of nonrigid parts.

  17. Recent developments in phyroshock simulation using fixtures with tunable resonant frequencies

    SciTech Connect

    Davie, N.T.; Bateman, V.I.

    1994-02-01

    Pyroshock is a potentially severe environment produced by the detonation of explosively actuated components and stage separation hardware. Electronic components exposed to pyroshock events during flight or deployment can be damaged by this high frequency, high G shock. Flight qualification of these components may be accomplished using one of many existing techniques to simulate the pyroshock environment in the laboratory. Two new techniques developed at Sandia National Laboratories allow larger components to be tested to a wide variety of pyroshock environments. The frequency content and amplitude of the simulated pyroshock can be easily controlled in a predictable manner. The pyroshock environment is produced by the resonant response of a test fixture that has been excited by a mechanical impact. The resonant fixture has a dominant frequency that can be continuously adjusted over a frequency range that is typically found in most pyroshock environments. The test apparatus and techniques utilized by each method will be described in this paper. Experimental results will be presented which illustrate the capabilities of each method.

  18. Test Fixture for Determination of Energy Absorbing Capabilities of Composite Materials

    NASA Technical Reports Server (NTRS)

    Lavoie, J. Andre (Inventor); Jackson, Karen E. (Inventor); Morton, John (Inventor)

    1998-01-01

    The present invention provides a fixture for supporting an elongated specimen for crush testing. The fixture comprises a base plate. four guiding rods, a sliding plate, four support rods and two collars. The guiding rods connect to the base plate and extend in a direction substantially perpendicular to the base plate. The sliding plate has linear bearings which encircle the guiding rods and enable translation of the sliding plate along the axis of each guiding rod. The four supporting rods mount to the base plate and also extend in a direction substantially perpendicular to the base plate. Each support rod has a keyway for a wedge which contacts the elongated specimen and holds the specimen in place during crushing. Each collar lies above the sliding plate and holds a pair of support rods on their ends opposite the ends connected to the base plate. A spherical bearing sits on top of the sliding plate and transfers an applied load to the sliding plate, which moves downward and crushes the elongated specimen.

  19. Dynamic 3-D virtual fixtures for minimally invasive beating heart procedures.

    PubMed

    Ren, Jing; Patel, Rajni V; McIsaac, Kenneth A; Guiraudon, Gerard; Peters, Terry M

    2008-08-01

    Two-dimensional or 3-D visual guidance is often used for minimally invasive cardiac surgery and diagnosis. This visual guidance suffers from several drawbacks such as limited field of view, loss of signal from time to time, and in some cases, difficulty of interpretation. These limitations become more evident in beating-heart procedures when the surgeon has to perform a surgical procedure in the presence of heart motion. In this paper, we propose dynamic 3-D virtual fixtures (DVFs) to augment the visual guidance system with haptic feedback, to provide the surgeon with more helpful guidance by constraining the surgeon's hand motions thereby protecting sensitive structures. DVFs can be generated from preoperative dynamic magnetic resonance (MR) or computed tomograph (CT) images and then mapped to the patient during surgery. We have validated the feasibility of the proposed method on several simulated surgical tasks using a volunteer's cardiac image dataset. Validation results show that the integration of visual and haptic guidance can permit a user to perform surgical tasks more easily and with reduced error rate. We believe this is the first work presented in the field of virtual fixtures that explicitly considers heart motion.

  20. Psychiatric admissions from crisis resolution teams in Norway: a prospective multicentre study

    PubMed Central

    2013-01-01

    Background Crisis resolution teams (CRTs) provide intensive alternative care to hospital admission for patients with mental health crises. The aims of this study were to describe the proportions and characteristics of patients admitted to in-patient wards from CRTs, to identify any differences in admission practices between CRTs, and to identify predictors of admissions from CRTs. Methods A naturalistic prospective multicentre design was used to study 680 consecutive patients under the care of eight CRTs in Norway over a 3-month period in 2005/2006. Socio-demographic and clinical data were collected on the patients, and on the organization and operation of the CRTs. Logistic regression analysis for hierarchical data was used to test potential predictors of admission at team and patient level. Results One hundred and forty-six patients (21.5%) were admitted to in-patient wards. There were significant differences in admission rates between the CRTs. The likelihood of being admitted to an in-patient ward was significantly lower for patients treated by CRTs that operated during extended opening hours than CRTs that operated during office hours only. Those most likely to be admitted were patients with psychotic symptoms, suicidal risk, and a prior history of admissions. Conclusions Extended opening hours may help CRTs to prevent more admissions for patients with moderately severe and relapsing mental illnesses. Patients with severe psychosis seem to be difficult to treat in the community by Norwegian CRTs even with extended opening hours. PMID:23594922

  1. Association of Intensive Care Unit Admission With Mortality Among Older Patients With Pneumonia

    PubMed Central

    Valley, Thomas S.; Sjoding, Michael W.; Ryan, Andrew M.; Iwashyna, Theodore J.; Cooke, Colin R.

    2016-01-01

    IMPORTANCE Among patients whose need for intensive care is uncertain, the relationship of intensive care unit (ICU) admission with mortality and costs is unknown. OBJECTIVE To estimate the relationship between ICU admission and outcomes for elderly patients with pneumonia. DESIGN, SETTING, AND PATIENTS Retrospective cohort study of Medicare beneficiaries (aged >64 years) admitted to 2988 acute care hospitals in the United States with pneumonia from 2010 to 2012. EXPOSURES ICU admission vs general ward admission. MAIN OUTCOMES AND MEASURES Primary outcome was 30-day all-cause mortality. Secondary outcomes included Medicare spending and hospital costs. Patient and hospital characteristics were adjusted to account for differences between patients with and without ICU admission. To account for unmeasured confounding, an instrumental variable was used—the differential distance to a hospital with high ICU admission (defined as any hospital in the upper 2 quintiles of ICU use). RESULTS Among 1 112 394 Medicare beneficiaries with pneumonia, 328 404 (30%) were admitted to the ICU. In unadjusted analyses, patients admitted to the ICU had significantly higher 30-day mortality, Medicare spending, and hospital costs than patients admitted to a general hospital ward. Patients (n = 553 597) living closer than the median differential distance (<3.3 miles) to a hospital with high ICU admission were significantly more likely to be admitted to the ICU than patients living farther away (n = 558 797) (36%for patients living closer vs 23%for patients living farther, P < .001). In adjusted analyses, for the 13%of patients whose ICU admission decision appeared to be discretionary (dependent only on distance), ICU admission was associated with a significantly lower adjusted 30-day mortality (14.8%for ICU admission vs 20.5%for general ward admission, P = .02; absolute decrease, −5.7%[95%CI, −10.6%, −0.9%]), yet there were no significant differences in Medicare spending or hospital

  2. Secukinumab efficacy and safety in indian patients with moderate-to-severe plaque psoriasis: Sub-analysis from FIXTURE, a randomized, placebo-controlled, phase 3 study

    PubMed Central

    Bhat, Ramesh M.; Leelavathy, B.; Aradhya, Sacchidanand S.; Gopal, Maragondanahalli G.; Pratap, D. V. S.; Mubashir, Mir; Srinivas, Putta; Pande, Sushil Y.; Thavkar, Amit S.

    2017-01-01

    Title: Secukinumab efficacy and safety in Indian patients with moderate-to-severe plaque psoriasis: sub-analysis from FIXTURE (Full Year Investigative Examination of Secukinumab vs. Etanercept Using Two Dosing Regimens to Determine Efficacy in Psoriasis), a randomized, placebo-controlled, phase 3 study. Background: Evidence has suggested Interleukin (IL)-17A to be an important effector cytokine in the pathogenesis of psoriasis. Here, we report results for an Indian sub-population from a multinational study FIXTURE, designed to assess the safety, tolerability, and long-term efficacy of fully human anti–IL-17A monoclonal antibody secukinumab in patients with moderate-to-severe plaque psoriasis. Materials and Methods: In this double-dummy, placebo controlled, 52-weeks phase 3 study FIXTURE, 149 Indian patients were randomized 1:1:1:1 to receive secukinumab at a dose of 300 mg or 150 mg, etanercept, or placebo. The study objective was to show the superiority of secukinumab over placebo at week 12, vis-à-vis proportion of patients achieving a reduction of 75% or more from the baseline in the psoriasis area-and-severity index score (PASI 75) and a score of 0 (clear) or 1 (almost clear) on a 5-point modified investigator's global assessment (IGA mod 2011) (co-primary end points). Results: At week 12, 61.0% and 55.9% patients in secukinumab 300 mg and 150 mg groups, respectively, achieved PASI 75 response compared to 20.0% in the etanercept and 7.1% in the placebo groups. Similarly, IGA mod 2011 0 or 1 response was achieved by 43.9% and 20.6% in patients in the secukinumab 300 mg and 150 mg group, respectively, vs. 13.3% in the etanercept and 2.4% in the placebo groups at week 12. Likewise, higher proportions of patients in secukinumab 300 mg (41.5%) and 150 mg (20.6%) group were PASI 90 responders at week 12 than those in the etanercept (10.0%) or placebo (0.0%) groups. The incidences of adverse events (AEs), during the induction period were similar in all the

  3. Qualitative critical incident study of patients’ experiences leading to emergency hospital admission with advanced respiratory illness

    PubMed Central

    Karasouli, Eleni; Munday, Daniel; Bailey, Cara; Staniszewska, Sophie; Hewison, Alistair; Griffiths, Frances

    2016-01-01

    Objectives The high volume of emergency admissions to hospital is a challenge for health systems internationally. Patients with lung cancer and chronic obstructive pulmonary disease (COPD) are frequently admitted to hospital as emergency cases. While the frequency of emergency admission has been investigated, few studies report patient experiences, particularly in relation to the decision-making process prior to emergency admission. We sought to explore patient and carer experiences and those of their healthcare professionals in the period leading up to emergency admission to hospital. Setting 3 UK hospitals located in different urban and rural settings. Design Qualitative critical incident study. Participants 24 patients with advanced lung cancer and 15 with advanced COPD admitted to hospital as emergencies, 20 of their carers and 50 of the health professionals involved in the patients’ care. Results The analysis of patient, carer and professionals’ interviews revealed a detailed picture of the complex processes involved leading to emergency admission to hospital. 3 phases were apparent in this period: self-management of deteriorating symptoms, negotiated decision-making and letting go. These were dynamic processes, characterised by an often rapidly changing clinical condition, uncertainty and anxiety. Patients considered their options drawing on experience, current and earlier advice. Patients tried to avoid admission, reluctantly accepting it, albeit often with a sense of relief, as anxiety increased with worsening symptoms. Conclusions Patients with advanced respiratory illness, and their carers, try to avoid emergency admission, and use logical and complex decision-making before reluctantly accepting it. Clinicians and policy-makers need to understand this complex process when considering how to reduce emergency hospital admissions rather than focusing on identifying and labelling admissions as ‘inappropriate’. PMID:26916687

  4. Antibiotic prescribing and admissions with major suppurative complications of respiratory tract infections: a data linkage study.

    PubMed Central

    Little, Paul; Watson, Louise; Morgan, Stephen; Williamson, Ian

    2002-01-01

    BACKGROUND: Systematic reviews of antibiotic treatment of common acute respiratory tract infections (RTIs) suggest modest symptomatic benefit, but provide limited evidence that prescribing prevents complications. AIM: To assess the relationship between penicillin prescribing (the most commonly used group of antibiotics for RTIs) and hospital admission with complications. DESIGN OF STUDY: Data linkage study. SETTING: Ninety-six health authorities of England for the year 1997-1998. METHOD: Hospital admissions related to RTIs were linked with prescribing analysis and cost (PACT) data. RESULTS: There was close correlation between items of penicillin use and total antibiotic use (r = 0.96). After controlling for SMR, age, sex, and Townsend score, a one-unit increase in penicillin use (items dispensed per capita) was associated with a reduction in annual incidence per 10,000 of admissions for quinsy (-3.55 admissions, 95% confidence interval [CI] = -6.85 to -0.26), and mastoiditis (square root of incidence of admissions = -1.05, 95% CI = -1.82 to -0.27). This does not represent lower referral thresholds among higher prescribers as higher prescribing was associated with more admissions for tonsillectomy and overall admissions. Increasing prescribing by 2000 items of penicillin for a practice of 10,000 patients could possibly prevent one admission for either mastoiditis or quinsy. CONCLUSION: Higher antibiotic prescribing is associated with significantly fewer admissions with major complications. However, the overall size of the effect is modest and it is difficult to advocate an overall increase in prescribing to prevent complications. Future research should concentrate on finding better methods of targeting antibiotics to individuals at risk of poor outcome. PMID:12030660

  5. Retrospective observational study of emergency admission, readmission and the ‘weekend effect’

    PubMed Central

    Shiue, Ivy; McMeekin, Peter; Price, Christopher

    2017-01-01

    Objectives Excess mortality following weekend hospital admission has been observed but not explained. As readmissions have greater age, comorbidity and social deprivation, outcomes following emergency index admission and readmission were examined for temporal and demographic associations to confirm whether weekend readmissions contribute towards excess mortality. Design A retrospective observational study. Individual patient Hospital Episode Statistics were linked and 2 categories created: index admissions (not within 60 days of discharge from an emergency hospitalisation) and readmissions (within 60 days of discharge from an emergency hospitalisation). Logistic regression examined associations between admission category, weekend and weekday mortality, age, gender, season, comorbidity and social deprivation. Setting A single acute National Health Service (NHS) trust serving a population of 550 000 via 3 emergency departments. Participants Emergency admissions between 1 January 2010 and 31 March 2015. Outcome measure All-cause 30-day mortality. Results Over 5 years there were 128 966 index admissions (74.7% weekday/25.3% weekend) and 20 030 readmissions (74.9% weekday/25.1% weekend). Adjusted 30-day death rates for weekday/weekend admissions were 6.93%/7.04% for index cases and 12.26%/13.27% for readmissions. Weekend readmissions had a higher mortality risk relative to weekday readmissions (OR 1.10 (95% CI 1.01 to 1.20)) without differences in comorbidity or deprivation. Weekend index admissions did not have a significantly increased mortality risk (OR 1.04 (95% CI 0.98 to 1.11)) but deaths which did occur were associated with lower deprivation (OR 1.24 (95% CI 1.11 to 1.38)) and an absence of comorbidities (OR 1.17 (1.02 to 1.34)). Conclusions Associations with emergency hospitalisation were not identical for index admissions and readmissions. Further research is needed to confirm what factors are responsible for the ‘weekend effect’. PMID:28255092

  6. The "Admissions" Side of BCCAT: An Update. Special Report

    ERIC Educational Resources Information Center

    British Columbia Council on Admissions and Transfer, 2008

    2008-01-01

    To spearhead increased emphasis on admissions, the British Columbia Council on Admissions and Transfer (BCCAT) formed an Admissions Committee in Fall 2003. The committee recognized the importance of institutional autonomy in determining admissions policies and processes at each institution. Following initiation of the Student Transitions Project…

  7. 46 CFR 154.406 - Design loads for cargo tanks and fixtures: General.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... −55 °C (−67 °F) or causes thermal stresses in cargo tank supports. (5) Sloshing loads, if the cargo...° to 30° range without exceeding the allowable stress of the material. (c) A hydrostatic...

  8. 46 CFR 154.406 - Design loads for cargo tanks and fixtures: General.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... −55 °C (−67 °F) or causes thermal stresses in cargo tank supports. (5) Sloshing loads, if the cargo...° to 30° range without exceeding the allowable stress of the material. (c) A hydrostatic...

  9. Decreasing avoidable hospital admissions with the implementation of an emergency department case management program.

    PubMed

    Sharieff, Ghazala Q; Cantonis, Matt; Tressler, Michelle; Whitehead, Mary; Russe, Jamie; Lovell, Eric

    2014-01-01

    With the passage of the Affordable Care Act, increased emphasis has been placed on optimizing quality and reducing expenditures. The use of an emergency department case manager (EDCM) is reemerging as an important initiative in the quest to provide high-quality care and decrease unnecessary hospital admissions. A pilot study of the use of EDCMs was conducted in one of the authors' EDs during a 6-month trial period. By using evidence-based criteria, the EDCM helped in real time to verify admission criteria, assisted with inpatient versus outpatient designation, found community alternatives to hospital admission, and initiated discharge planning for patients who required admission and were at high risk for readmission. EDCMs also worked with pharmacists to assist with medication management for patients who required assistance with obtaining prescriptions. Because of the pilot study's success, the authors' health care system will be implementing EDCMs throughout the organization.

  10. Locker Rooms: The Durable Design.

    ERIC Educational Resources Information Center

    Viklund, Roy; Coons, John

    1997-01-01

    Offers advice on heavy-use locker-room design that provides easier maintenance and vandal resistance. Design features and materials used for flooring, ceilings, and walls are addressed as are built-in systems and equipment, toilet and shower fixtures and partitions, lockers, and mechanical and electrical systems. (GR)

  11. Assessing Practical Intelligence in Business School Admissions: A Supplement to the Graduate Management Admissions Test

    ERIC Educational Resources Information Center

    Hedlund, Jennifer; Wilt, Jeanne M.; Nebel, Kristina L.; Ashford, Susan J.; Sternberg, Robert J.

    2006-01-01

    The Graduate Management Admission Test (GMAT) is the most widely used measure of managerial potential in MBA admissions. GMAT scores, although predictive of grades in business school, leave much of the variance in graduate school performance unexplained. The GMAT also produces disparities in test scores between groups, generating the potential for…

  12. Major Research Efforts of the Law School Admission Council. Law School Admission Research.

    ERIC Educational Resources Information Center

    Hart, Frederick M.; Evans, Franklin R.

    Research conducted by the Law School Admission Council since the development of the Law School Admission Test (LSAT) in 1948 is described. An overview of the research topics is provided, and relevant published reports are cited in 61 footnotes. The following topics of study are discussed: (1) use and validity of traditional predictors of law…

  13. Multiple hospital admissions in a calendar year.

    PubMed

    Newton, J; Goldacre, M

    1993-09-01

    Hospital in-patient workload is routinely measured as episodes of care. We report on the extent to which counts of episodes of care differ from counts of patients treated in different specialties and in different age groups. Linked records of hospital care in a population of 1.9 million people, collected over an 11-year period (1976-1986), were analysed. The all-ages multiple admission ratio (the number of admissions per 100 people admitted in the same specialty and year) varied between specialties from 102 to 171. Medical specialties tended to have higher ratios than surgical ones. The influence of age on multiple admission ratios varied between specialties, although in general the ratios increased with increasing age. There were progressive but small increases in multiple admission ratios over the period studied in a number of specialties but, by and large, stability over time was more striking than any change. The information presented could be used to estimate person-based admission rates from available episode-based data where the former are not available. This should be helpful both in managing hospital resources and in purchasing care on behalf of resident populations. Purchasers in particular should be aware of numbers of people being treated as well as the numbers of episodes of care provided.

  14. Factors correlating with delayed trauma center admission following traumatic brain injury

    PubMed Central

    2013-01-01

    Background Delayed admission to appropriate care has been shown increase mortality following traumatic brain injury (TBI). We investigated factors associated with delayed admission to a hospital with neurosurgical expertise in a cohort of TBI patients in the intensive care unit (ICU). Methods A retrospective analysis of all TBI patients treated in the ICUs of Helsinki University Central Hospital was carried out from 1.1.2009 to 31.12.2010. Patients were categorized into two groups: direct admission and delayed admission. Patients in the delayed admission group were initially transported to a local hospital without neurosurgical expertise before inter-transfer to the designated hospital. Multivariate logistic regression was utilized to identify pre-hospital factors associated with delayed admission. Results Of 431 included patients 65% of patients were in the direct admission groups and 35% in the delayed admission groups (median time to admission 1:07h, IQR 0:52–1:28 vs. 4:06h, IQR 2:53–5:43, p <0.001). In multivariate analysis factors increasing the likelihood of delayed admission were (OR, 95% CI): male gender (3.82, 1.60-9.13), incident at public place compared to home (0.26, 0.11-0.61), high energy trauma (0.05, 0.01-0.28), pre-hospital physician consultation (0.15, 0.06-0.39) or presence (0.08, 0.03-0.22), hypotension (0.09, 0.01-0.93), major extra cranial injury (0.17, 0.05-0.55), abnormal pupillary light reflex (0.26, 0.09-0.73) and severe alcohol intoxication (12.44, 2.14-72.38). A significant larger proportion of patients in the delayed admission group required acute craniotomy for mass lesion when admitted to the neurosurgical hospital (57%, 21%, p< 0.001). No significant difference in 6-month mortality was noted between the groups (p= 0.814). Conclusion Delayed trauma center admission following TBI is common. Factors increasing likelihood of this were: male gender, incident at public place compared to home, low energy trauma, absence of pre

  15. 40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production without water wash spray booth(s)...

  16. 40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production with water wash spray booth(s) or...

  17. SR-71A in Flight with Test Fixture Mounted Atop the Aft Section of the Aircraft

    NASA Technical Reports Server (NTRS)

    1999-01-01

    This close-up, head-on view of NASA's SR-71A Blackbird in flight shows the aircraft with an experimental test fixture mounted on the back of the airplane. Two SR-71 aircraft have been used by NASA as testbeds for high-speed and high-altitude aeronautical research. The aircraft, an SR-71A and an SR-71B pilot trainer aircraft, have been based here at NASA's Dryden Flight Research Center, Edwards, California. They were transferred to NASA after the U.S. Air Force program was cancelled. As research platforms, the aircraft can cruise at Mach 3 for more than one hour. For thermal experiments, this can produce heat soak temperatures of over 600 degrees Fahrenheit (F). This operating environment makes these aircraft excellent platforms to carry out research and experiments in a variety of areas -- aerodynamics, propulsion, structures, thermal protection materials, high-speed and high-temperature instrumentation, atmospheric studies, and sonic boom characterization. The SR-71 was used in a program to study ways of reducing sonic booms or over pressures that are heard on the ground, much like sharp thunderclaps, when an aircraft exceeds the speed of sound. Data from this Sonic Boom Mitigation Study could eventually lead to aircraft designs that would reduce the 'peak' overpressures of sonic booms and minimize the startling affect they produce on the ground. One of the first major experiments to be flown in the NASA SR-71 program was a laser air data collection system. It used laser light instead of air pressure to produce airspeed and attitude reference data, such as angle of attack and sideslip, which are normally obtained with small tubes and vanes extending into the airstream. One of Dryden's SR-71s was used for the Linear Aerospike Rocket Engine, or LASRE Experiment. Another earlier project consisted of a series of flights using the SR-71 as a science camera platform for NASA's Jet Propulsion Laboratory in Pasadena, California. An upward-looking ultraviolet video camera

  18. Optimization of fixture layouts of glass laser optics using multiple kernel regression.

    PubMed

    Su, Jianhua; Cao, Enhua; Qiao, Hong

    2014-05-10

    We aim to build an integrated fixturing model to describe the structural properties and thermal properties of the support frame of glass laser optics. Therefore, (a) a near global optimal set of clamps can be computed to minimize the surface shape error of the glass laser optic based on the proposed model, and (b) a desired surface shape error can be obtained by adjusting the clamping forces under various environmental temperatures based on the model. To construct the model, we develop a new multiple kernel learning method and call it multiple kernel support vector functional regression. The proposed method uses two layer regressions to group and order the data sources by the weights of the kernels and the factors of the layers. Because of that, the influences of the clamps and the temperature can be evaluated by grouping them into different layers.

  19. [Medical examination prior to trade school admission].

    PubMed

    Hursidić-Radulović, Azra; Decković-Vukres, Vlasta

    2005-01-01

    Regulation on medical examination prior to apprenticeship is built in the Act on Trades and Crafts. Medical examinations of the students before admission to secondary craft schools have been done regularly since 1993. Between 11,000 and 14,000 students are admitted to secondary craft schools in the Republic of Croatia annually. According to statistics, about 10% of students have obvious health problems, about 5% of students have healt problems which vitally limit their capacity in particular crafts. This statistic refers to about 3% of the examined students. Medical examinations of students prior to admission to craft schools represent a particular sort of health capacity examinations. The paper includes applications for the most freqent trades and crafts, and findings of the craft school admission examinations.

  20. [Involuntary admission of addict during early pregnancy].

    PubMed

    Hondius, Adger J K; Stikker, Tineke E; Wennink, J M B Hanneke; Honig, Adriaan

    2012-01-01

    A 30-year-old cocaine-dependent woman was 16 weeks pregnant. Because of possible endangerment of the fetus, an involuntary provisional admission was authorized. Of particular interest is the application of the Dutch Act on Formal Admissions to Psychiatric Hospitals for the primary diagnosis 'addiction' and the fact that the fetus was regarded as a legal 'other'. In severe cases of addiction combined with pregnancy an earlier intervention is needed and arrangement of accelerated legal custody of the newborn before birth should be considered. For the protection of the unborn, we advocate a stricter application of the United Nations Convention on the Rights of the Child. Information for addicted women with preconception counselling can help prevent a compulsory admission.

  1. Northern Territory Heart Failure Initiative–Clinical Audit (NTHFI–CA)–a prospective database on the quality of care and outcomes for acute decompensated heart failure admission in the Northern Territory: study design and rationale

    PubMed Central

    Iyngkaran, Pupalan; Tinsley, Jeff; Smith, David; Haste, Mark; Nadarajan, Kangaharan; Ilton, Marcus; Battersby, Malcolm; Stewart, Simon; Brown, Alex

    2014-01-01

    Introduction Congestive heart failure is a significant cause of morbidity and mortality in Australia. Accurate data for the Northern Territory and Indigenous Australians are not presently available. The economic burden of this chronic cardiovascular disease is felt by all funding bodies and it still remains unclear what impact current measures have on preventing the ongoing disease burden and how much of this filters down to more remote areas. Clear differentials also exist in rural areas including a larger Indigenous community, greater disease burden, differing aetiologies for heart failure as well as service and infrastructure discrepancies. It is becoming increasingly clear that urban solutions will not affect regional outcomes. To understand regional issues relevant to heart failure management, an understanding of the key performance indicators in that setting is critical. Methods and analysis The Northern Territory Heart Failure Initiative—Clinical Audit (NTHFI-CA) is a prospective registry of acute heart failure admissions over a 12-month period across the two main Northern Territory tertiary hospitals. The study collects information across six domains and five dimensions of healthcare. The study aims to set in place an evidenced and reproducible audit system for heart failure and inform the developing heart failure disease management programme. The findings, is believed, will assist the development of solutions to narrow the outcomes divide between remote and urban Australia and between Indigenous and Non-Indigenous Australians, in case they exist. A combination of descriptive statistics and mixed effects modelling will be used to analyse the data. Ethics and dissemination This study has been approved by respective ethics committees of both the admitting institutions. All participants will be provided a written informed consent which will be completed prior to enrolment in the study. The study results will be disseminated through local and international

  2. Do health checks for adults with intellectual disability reduce emergency hospital admissions? Evaluation of a natural experiment

    PubMed Central

    Hosking, Fay J; Harris, Tess; DeWilde, Stephen; Beighton, Carole; Shah, Sunil M; Cook, Derek G

    2017-01-01

    Background Annual health checks for adults with intellectual disability (ID) have been incentivised by National Health Service (NHS) England since 2009, but it is unclear what impact they have had on important health outcomes such as emergency hospitalisation. Methods An evaluation of a ‘natural experiment’, incorporating practice and individual-level designs, to assess the effectiveness of health checks for adults with ID in reducing emergency hospital admissions using a large English primary care database. For practices, changes in admission rates for adults with ID between 2009–2010 and 2011–2012 were compared in 126 fully participating versus 68 non-participating practices. For individuals, changes in admission rates before and after the first health check for 7487 adults with ID were compared with 46 408 age-sex-practice matched controls. Incident rate ratios (IRRs) comparing changes in admission rates are presented for: all emergency, preventable emergency (for ambulatory care sensitive conditions (ACSCs)) and elective emergency. Results Practices with high health check participation showed no change in emergency admission rate among patients with ID over time compared with non-participating practices (IRR=0.97, 95% CI 0.78 to 1.19), but emergency admissions for ACSCs did fall (IRR=0.74, 0.58 to 0.95). Among individuals with ID, health checks had no effect on overall emergency admissions compared with controls (IRR=0.96, 0.87 to 1.07), although there was a relative reduction in emergency admissions for ACSCs (IRR=0.82, 0.69 to 0.99). Elective admissions showed no change with health checks in either analysis. Conclusions Annual health checks in primary care for adults with ID did not alter overall emergency admissions, but they appeared influential in reducing preventable emergency admissions. PMID:27312249

  3. Predicting trauma admissions: the effect of weather, weekday, and other variables.

    PubMed

    Friede, Kevin A; Osborne, Marc C; Erickson, Darin J; Roesler, Jon S; Azam, Arsalan; Croston, J Kevin; McGonigal, Michael D; Ney, Arthur L

    2009-11-01

    One of the challenges all hospitals, especially designated trauma centers, face is how to make sure they have adequate staffing on various days of the week and at various times of the year. A number of studies have explored whether factors such as weather, temporal variation, holidays, and events that draw mass gatherings may be useful for predicting patient volume. This article looks at the effects of weather, mass gatherings, and calendar variables on daily trauma admissions at the three Level I trauma hospitals in the Minneapolis-St. Paul metropolitan area. Using ARIMA statistical modeling, we found that weekends, summer, lack of rain, and snowfall were all predictive of daily trauma admissions; holidays and mass gatherings such as sporting events were not. The forecasting model was successful in reflecting the pattern of trauma admissions; however, it's usefulness was limited in that the predicted range of daily trauma admissions was much narrower than the observed number of admissions. Nonetheless, the observed pattern of increased admission in the summer months and year-round on Saturdays should be helpful in resource planning.

  4. Parenteral penicillin for children with meningococcal disease before hospital admission: case-control study

    PubMed Central

    Harnden, Anthony; Ninis, Nelly; Thompson, Matthew; Perera, Rafael; Levin, Michael; Mant, David; Mayon-White, Richard

    2006-01-01

    Objective To explore the impact on mortality and morbidity of parenteral penicillin given to children before admission to hospital with suspected meningococcal disease. Design Retrospective comparison of fatal and non-fatal cases. Setting England, Wales, and Northern Ireland; December 1997 to February 1999. Participants 158 children aged 0-16 years (26 died, 132 survived) in whom a general practitioner had made the diagnosis of meningococcal disease before hospital admission. Results Administration of parenteral penicillin by general practitioners was associated with increased odds ratios for death (7.4, 95% confidence interval 1.5 to 37.7) and complications in survivors (5.0, 1.7 to 15.0). Children who received penicillin had more severe disease on admission (median Glasgow meningococcal septicaemia prognostic score (GMSPS) 6.5 v 4.0, P = 0.002). Severity on admission did not differ significantly with time taken to reach hospital. Conclusions Children who were given parenteral penicillin by a general practitioner had more severe disease on reaching hospital than those who were not given penicillin before admission. The association with poor outcome may be because children who are more severely ill are being given penicillin before admission. PMID:16554335

  5. Efficacy of Admission Screening for Extended-Spectrum Beta-Lactamase Producing Enterobacteriaceae

    PubMed Central

    Lowe, Christopher F.; Katz, Kevin; McGeer, Allison J.; Muller, Matthew P.

    2013-01-01

    Objective We hypothesized that admission screening for extended-spectrum β-lactamase-producing Enterobacteriaceae (ESBL-E) reduces the incidence of hospital-acquired ESBL-E clinical isolates. Design Retrospective cohort study. Setting 12 hospitals (6 screening and 6 non-screening) in Toronto, Canada. Patients All adult inpatients with an ESBL-E positive culture collected from 2005–2009. Methods Cases were defined as hospital-onset (HO) or community-onset (CO) if cultures were positive after or before 72 hours. Efficacy of screening in reducing HO-ESBL-E incidence was assessed with a negative binomial model adjusting for study year and CO-ESBL-E incidence. The accuracy of the HO-ESBL-E definition was assessed by re-classifying HO-ESBL-E cases as confirmed nosocomial (negative admission screen), probable nosocomial (no admission screen) or not nosocomial (positive admission screen) using data from the screening hospitals. Results There were 2,088 ESBL-E positive patients and incidence of ESBL-E rose from 0.11 to 0.42 per 1,000 inpatient days between 2005 and 2009. CO-ESBL-E incidence was similar at screening and non-screening hospitals but screening hospitals had a lower incidence of HO-ESBL-E in all years. In the negative binomial model, screening was associated with a 49.1% reduction in HO-ESBL-E (p<0.001). A similar reduction was seen in the incidence of HO-ESBL-E bacteremia. When HO-ESBL-E cases were re-classified based on their admission screen result, 46.5% were positive on admission, 32.5% were confirmed as nosocomial and 21.0% were probable nosocomial cases. Conclusions Admission screening for ESBL-E is associated with a reduced incidence of HO-ESBL-E. Controlled, prospective studies of admission screening for ESBL-E should be a priority. PMID:23638132

  6. 40 CFR 89.604 - Conditional admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., the importer must store the nonroad engine at a location where the Administrator has reasonable access...) CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Importation of Nonconforming Nonroad Engines § 89.604 Conditional admission. (a) A nonroad engine offered for importation under §...

  7. The National Center Test for University Admissions

    ERIC Educational Resources Information Center

    Watanabe, Yoshinori

    2013-01-01

    This article describes the National Center Test for University Admissions, a unified national test in Japan, which is taken by 500,000 students every year. It states that implementation of the Center Test began in 1990, with the English component consisting only of the written section until 2005, when the listening section was first implemented…

  8. 34 CFR 106.15 - Admissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... higher education, and public institutions of undergraduate higher education. (e) Public institutions of undergraduate higher education. Subpart C does not apply to any public institution of undergraduate higher... 34 Education 1 2014-07-01 2014-07-01 false Admissions. 106.15 Section 106.15 Education...

  9. 34 CFR 106.15 - Admissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... higher education, and public institutions of undergraduate higher education. (e) Public institutions of undergraduate higher education. Subpart C does not apply to any public institution of undergraduate higher... 34 Education 1 2011-07-01 2011-07-01 false Admissions. 106.15 Section 106.15 Education...

  10. 34 CFR 106.15 - Admissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... higher education, and public institutions of undergraduate higher education. (e) Public institutions of undergraduate higher education. Subpart C does not apply to any public institution of undergraduate higher... 34 Education 1 2012-07-01 2012-07-01 false Admissions. 106.15 Section 106.15 Education...

  11. 34 CFR 106.15 - Admissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... higher education, and public institutions of undergraduate higher education. (e) Public institutions of undergraduate higher education. Subpart C does not apply to any public institution of undergraduate higher... 34 Education 1 2010-07-01 2010-07-01 false Admissions. 106.15 Section 106.15 Education...

  12. 34 CFR 106.15 - Admissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... higher education, and public institutions of undergraduate higher education. (e) Public institutions of undergraduate higher education. Subpart C does not apply to any public institution of undergraduate higher... 34 Education 1 2013-07-01 2013-07-01 false Admissions. 106.15 Section 106.15 Education...

  13. PREP: Outreach to Online Learners through Admissions

    ERIC Educational Resources Information Center

    Gupton, Preeti

    2016-01-01

    Librarians have collaborated with academic departments within their institutions for decades now, working with professors and administrators to bring information literacy skills to students. The librarians at National American University decided to extend this collaboration to a non-academic unit, the admissions department of the university. The…

  14. 18 CFR 1317.220 - Admissions.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 2 2014-04-01 2014-04-01 false Admissions. 1317.220 Section 1317.220 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE...

  15. 18 CFR 1317.220 - Admissions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 2 2013-04-01 2012-04-01 true Admissions. 1317.220 Section 1317.220 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE...

  16. 18 CFR 1317.220 - Admissions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 2 2012-04-01 2012-04-01 false Admissions. 1317.220 Section 1317.220 Conservation of Power and Water Resources TENNESSEE VALLEY AUTHORITY NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE...

  17. Open Admissions: The Pros and Cons.

    ERIC Educational Resources Information Center

    Barzun, Jacques; And Others

    The Council for Basic Education sponsored an all-day symposium on open admissions in 1971. This booklet contains the full text of the addresses given on that occasion, as well as the major part of the discussion among the panelists and answers to questions from the audience. The aim of the symposium was not only to provide information about…

  18. Foreign Language, the Classics, and College Admissions.

    ERIC Educational Resources Information Center

    LaFleur, Richard A.

    1993-01-01

    This article reports the results of a survey, funded by the American Classical League (ACL) and conducted during 1990-91, that assessed attitudes toward high school foreign-language study, in particular the study of Latin and Greek, in the college admissions process. (21 references) (VWL)

  19. Beyond Admission: The Challenge for Access.

    ERIC Educational Resources Information Center

    Roger, Angela; Sutherland, Margaret

    1992-01-01

    The Scottish Wider Access Programme (SWAP) aims to increase adults' access to higher education. Interviews with SWAP students and educators revealed that SWAP had been invaluable in preparing nontraditional students for admission to higher education. Issues include improving teaching methods geared toward mature students, providing support…

  20. The Admissions Criteria of Secondary Free Schools

    ERIC Educational Resources Information Center

    Morris, Rebecca

    2014-01-01

    This paper presents the results of an analysis of the admissions criteria used by the first two waves of secondary Free Schools in England. The type of criteria and their ranked order is explored and their potential impact on the school composition is considered. The findings demonstrate the diversity of criteria being used by this new type of…

  1. 15 CFR 8a.220 - Admissions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Admissions. 8a.220 Section 8a.220 Commerce and Foreign Trade Office of the Secretary of Commerce NONDISCRIMINATION ON THE BASIS OF SEX IN... institution. (c) Application of §§ 8a.300 through .310. Except as provided in paragraphs (d) and (e) of...

  2. Reporting Subscores from College Admission Tests

    ERIC Educational Resources Information Center

    Lyren, Per-Erik

    2009-01-01

    The added value of reporting subscores on a college admission test (SweSAT) was examined in this study. Using a CTT-derived objective method for determining the value of reporting subscores, it was concluded that there is added value in reporting section scores (Verbal/Quantitative) as well as subtest scores. These results differ from a study of…

  3. 40 CFR 5.300 - Admission.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Admission. 5.300 Section 5.300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of...

  4. 40 CFR 5.300 - Admission.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Admission. 5.300 Section 5.300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of...

  5. "Stealth Applicants" Are Changing the Admissions Equation

    ERIC Educational Resources Information Center

    Hoover, Eric

    2008-01-01

    Jeff Rickey is a numbers guy. But three years ago, a colleague asked him about something he'd never counted: applicants who came out of nowhere. The question intrigued Mr. Rickey, dean of admissions and financial aid at Earlham College in Indiana. He found that 17 percent of the college's applicants that year had not called, taken a tour, or…

  6. 10 CFR 2.708 - Admissions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 1 2012-01-01 2012-01-01 false Admissions. 2.708 Section 2.708 Energy NUCLEAR REGULATORY COMMISSION RULES OF PRACTICE FOR DOMESTIC LICENSING PROCEEDINGS AND ISSUANCE OF ORDERS Rules for Formal... the request is directed serves on the requesting party either: (i) A sworn statement...

  7. EARLY SCHOOL ADMISSIONS PROJECT, PROMISING PRACTICES.

    ERIC Educational Resources Information Center

    Baltimore City Public Schools, MD.

    THE EXPERIMENTAL PROJECT ATTEMPTS TO DETERMINE WHETHER EARLY ADMISSION TO SCHOOL CAN OVERCOME BARRIERS TO LEARNING WHICH ENVIRONMENTAL FACTORS SEEM TO IMPOSE. A DEPRIVED CHILD OFTEN DOES NOT RECEIVE ATTENTION, AFFECTION, OR GUIDANCE WITHIN HIS HOME. THE YOUNG CHILD SHOULD BE HELPED TO DEVELOP A WHOLESOME SELF-CONCEPT, TO ACQUIRE THE DRIVE TO…

  8. Hospital admissions before and after shipyard closure.

    PubMed Central

    Iversen, L.; Sabroe, S.; Damsgaard, M. T.

    1989-01-01

    To determine the effect of job loss on health an investigation was made of admissions to hospitals in 887 men five years before and three years after the closure of a Danish shipyard. The control group comprised 441 men from another shipyard. The information on hospital admissions was obtained from the Danish national register of patients. The relative risk of admission in the control group dropped significantly in terms of the number of men admitted from the study group from 1.29 four to five years before closure to 0.74 in the three years after closure. This was especially true of admissions due to accidents (1.33 to 0.46) and diseases of the digestive system (4.53 to 1.03). For diseases of the circulatory system, particularly cardiovascular diseases, the relative risk increased from 0.8 to 1.60, and from 1.0 to 2.6 respectively. These changes in risk of illness after redundancy are probably a consequence of a change from the effects of a high risk work environment to the effects of psychosocial stresses such as job insecurity and unemployment. PMID:2511968

  9. University Admissions. Policy Note. Number 3

    ERIC Educational Resources Information Center

    Group of Eight (NJ1), 2012

    2012-01-01

    University admissions, like many other aspects of the higher education sector, are going through a time of significant change. From 2012, universities will receive full funding under the Commonwealth Grants Scheme (CGS) for as many places as they offer. Previously, the Government limited the number of funded places, with a tolerance band for…

  10. Differential Prediction Generalization in College Admissions Testing

    ERIC Educational Resources Information Center

    Aguinis, Herman; Culpepper, Steven A.; Pierce, Charles A.

    2016-01-01

    We introduce the concept of "differential prediction generalization" in the context of college admissions testing. Specifically, we assess the extent to which predicted first-year college grade point average (GPA) based on high-school grade point average (HSGPA) and SAT scores depends on a student's ethnicity and gender and whether this…

  11. Air pollution and emergency hospital admissions for cardiovascular diseases in Valencia, Spain

    PubMed Central

    Ballester, F; Tenias, J; Perez-Hoyos, S

    2001-01-01

    STUDY OBJECTIVE—To estimate the short-term association between air pollution levels and emergency hospital admissions for cardiovascular diseases in Valencia, within 1994-1996 period.
DESIGN—Daily levels of air pollution and emergency admissions for cardiovascular diseases were related to using an ecological time series design. The number of admissions was obtained from the hospital records database. Selected groups of causes were all cardiovascular diseases, heart admissions, and admissions for cerebrovascular diseases. The number of admissions for digestive diseases was used as control. Pollutants were black smoke, sulphur dioxide (SO2), nitrogen dioxide (NO2), carbon monoxide (CO) and ozone (O3). Magnitude of association was estimated by Poisson autoregresive regression. Estimations were calculated according the hottest (May to October) and the coldest (November to April) periods.
SETTING—City of Valencia, Spain, about 750 000 inhabitants.
PARTICIPANTS—People being admitted to the two major hospitals in the city, with a catchment area of nearly 400 000 inhabitants.
MAIN RESULTS—For the whole period, a significant association for SO2-24 h was found so a rise in its levels of 10 µg/m3 was associated with an increment of 3% (95%CI 0.4 to 5.7%) in the expected number of cardiovascular admissions. A significant association for black smoke, SO2-24 h, SO2-1 h, and CO-1 h was found in the hottest semester. All these associations were verified with a lag of two days. The estimates of the associations for particles, SO2, and CO were affected by the inclusion of the other pollutants in their models. NO2 was independently associated with cerebrovascular admissions. There were no significant associations between air pollution and admissions for digestive diseases.
CONCLUSIONS—Current levels of air pollution and emergency cardiovascular admissions are significantly related in Valencia.


Keywords: air pollution; cardiovascular disease

  12. Inlet Housing for a Partial-Admission Turbine

    NASA Technical Reports Server (NTRS)

    Moye, Ralph; Myers, William; Baker, Kevin

    2004-01-01

    An inlet housing for a partial-admission turbine has been designed to cause the inlet airflow to make a smooth transition from an open circular inlet to an inlet slot. The smooth flow is required for purposes of measuring inlet flow characteristics and maximizing the efficiency of the turbine. A partial-admission turbine is a turbine in which the inlet slot occupies less than a complete circle around the rotor axis. In this case, the inlet slot occupies a 90 arc. The present special inlet-housing design is needed because the "bull nose" shape of a conventional turbine inlet housing fails to provide the required smooth transition in a partial-admission configuration and thereby gives rise to a loss of turbine efficiency and inaccuracies in inlet flow measurements. Upon entering the inlet housing through the circular opening, the flow encounters a "tongue"-shaped passageway, which serves as a ramp that diverts the flow to the first of two straight passages. This first passageway occupies a 90 arc and has a length equal to two passage heights. Instrumentation rakes for measuring the characteristics of the inlet flow are installed in this passageway. Just past the first straight passageway is the second one, which is narrower and leads to the 90 turbine inlet slot. This passageway is used to smooth the flow immediately prior to its passage through the turbine inlet slot. The length of this second passageway equals the length of the chord of a turbine vane. The inlet housing incorporates small ports for measuring static pressures at various locations of the flow, and incorporates bosses for the installation of the instrumentation rakes. The inlet housing also includes a flange at its inlet end for attachment to a circular inlet duct and a flange at its outlet end for attachment to the outer casing of the turbine.

  13. The Probabilistic Admissible Region with Additional Constraints

    NASA Astrophysics Data System (ADS)

    Roscoe, C.; Hussein, I.; Wilkins, M.; Schumacher, P.

    The admissible region, in the space surveillance field, is defined as the set of physically acceptable orbits (e.g., orbits with negative energies) consistent with one or more observations of a space object. Given additional constraints on orbital semimajor axis, eccentricity, etc., the admissible region can be constrained, resulting in the constrained admissible region (CAR). Based on known statistics of the measurement process, one can replace hard constraints with a probabilistic representation of the admissible region. This results in the probabilistic admissible region (PAR), which can be used for orbit initiation in Bayesian tracking and prioritization of tracks in a multiple hypothesis tracking framework. The PAR concept was introduced by the authors at the 2014 AMOS conference. In that paper, a Monte Carlo approach was used to show how to construct the PAR in the range/range-rate space based on known statistics of the measurement, semimajor axis, and eccentricity. An expectation-maximization algorithm was proposed to convert the particle cloud into a Gaussian Mixture Model (GMM) representation of the PAR. This GMM can be used to initialize a Bayesian filter. The PAR was found to be significantly non-uniform, invalidating an assumption frequently made in CAR-based filtering approaches. Using the GMM or particle cloud representations of the PAR, orbits can be prioritized for propagation in a multiple hypothesis tracking (MHT) framework. In this paper, the authors focus on expanding the PAR methodology to allow additional constraints, such as a constraint on perigee altitude, to be modeled in the PAR. This requires re-expressing the joint probability density function for the attributable vector as well as the (constrained) orbital parameters and range and range-rate. The final PAR is derived by accounting for any interdependencies between the parameters. Noting that the concepts presented are general and can be applied to any measurement scenario, the idea

  14. A 3-d modular gripper design tool

    SciTech Connect

    Brown, R.G.; Brost, R.C.

    1997-02-01

    Modular fixturing kits are sets of components used for flexible, rapid construction of fixtures. A modular vise is a parallel-jaw vise, each jaw of which is a modular fixture plate with a regular grid of precisely positioned holes. To fixture a part, one places pins in some of the holes so that when the vise is closed, the part is reliably located and completely constrained. The modular vise concept can be adapted easily to the design of modular parallel-jaw grippers for robots. By attaching a grid-plate to each jaw of a parallel-jaw gripper, one gains the ability to easily construct high-quality grasps for a wide variety of parts from a standard set of hardware. Wallack and Canny developed an algorithm for planning planar grasp configurations for the modular vise. In this paper, the authors expand this work to produce a 3-d fixture/gripper design tool. They describe several analyses they have added to the planar algorithm, including a 3-d grasp quality metric based on force information, 3-d geometric loading analysis, and inter-gripper interference analysis. Finally, the authors describe two applications of their code. One of these is an internal application at Sandia, while the other shows a potential use of the code for designing part of an agile assembly line.

  15. Guideposts of an Effective Admissions Program for the Private School.

    ERIC Educational Resources Information Center

    Johnson, Raymond E.

    1980-01-01

    Describes fundamental guideposts for an effective private school admissions program. Included are a clear statement of purpose, informative literature, clearly stated admission requirements, standardized testing, a cooperative faculty, image positioning and a recruiting plan. (RC)

  16. Reclaiming the Educational Role of Chief Admission Officers.

    ERIC Educational Resources Information Center

    McDonough, Patricia; Robertson, Larry

    1995-01-01

    Describes changes that have occurred in high schools, colleges, and the entrepreneurial admission sector. Relates the evolution of the admission officer's job since the early 1960s and the profession's rapid growth. Details the hybrid role of marketer and educator for chief admissions officers, and issues a call for professional standards. (RJM)

  17. Female and Male Admission to Graduate School: An Illustrative Inquiry

    ERIC Educational Resources Information Center

    Maxwell, Scott E.; Jones, Lyle V.

    1976-01-01

    Female and male admission rates to four graduate programs at a university were compared over a two year time period to assess possible sex bias in admission procedures. The overall results showed that sex played only a modest role in admission decisions. (Author/DEP)

  18. Behind the Scenes, Admissions Offices Conquer Mounds of Mail

    ERIC Educational Resources Information Center

    Farrell, Elizabeth F.

    2008-01-01

    If coming back to work after winter break seems daunting, consider the plight of college-admissions officials. While most high-school students are breathing a sigh of relief after finally submitting their applications, those on the receiving end are rolling up their sleeves. January is crunch time for many admissions offices. Admissions officers…

  19. 45 CFR 618.305 - Preference in admission.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 3 2011-10-01 2011-10-01 false Preference in admission. 618.305 Section 618.305 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 618.305 Preference in admission....

  20. 45 CFR 618.305 - Preference in admission.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Preference in admission. 618.305 Section 618.305 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 618.305 Preference in admission....

  1. 45 CFR 618.305 - Preference in admission.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 3 2013-10-01 2013-10-01 false Preference in admission. 618.305 Section 618.305 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 618.305 Preference in admission....

  2. 45 CFR 618.305 - Preference in admission.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 3 2012-10-01 2012-10-01 false Preference in admission. 618.305 Section 618.305 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION... Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 618.305 Preference in admission....

  3. The Roles of Testing and Diversity in College Admissions.

    ERIC Educational Resources Information Center

    Clarke, Marguerite; Shore, Arnold

    In order to understand the roles of test scores and diversity characteristics (including race and ethnicity) in the admission process, National Board researchers interviewed admissions directors who worked at selective public and private institutions are well as admissions consultants in the summer and fall of 1999. This report presents an…

  4. Equity of Access. New Approaches to Minority Admissions

    ERIC Educational Resources Information Center

    Bingham, Rebecca Saady

    1978-01-01

    One new approach to the admission of minorities to medical schools is that of the Simulated Minority Admission Exercises (SMAE). It sensitizes admission committee members to the different backgrounds of minority applicants and teaches them to evaluate them more effectively. (Author/AM)

  5. 49 CFR 511.34 - Requests for admission.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... for the admission, for the purposes of the pending proceeding only, of the truth of any matters within... served upon any party after filing of the answer. Each matter as to which an admission is requested shall be separately set forth. (b) Procedure for response. The matter as to which an admission is...

  6. 6 CFR 17.305 - Preference in admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 6 Domestic Security 1 2010-01-01 2010-01-01 false Preference in admission. 17.305 Section 17.305... OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 17.305 Preference in admission. A...

  7. 18 CFR 1317.305 - Preference in admission.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Preference in admission... NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1317.305 Preference in admission....

  8. 49 CFR 1114.3 - Admissibility of business records.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 8 2013-10-01 2013-10-01 false Admissibility of business records. 1114.3 Section... § 1114.3 Admissibility of business records. Any writing or record, whether in the form of an entry in a... be admissible as evidence thereof if it appears that it was made in the regular course of...

  9. 49 CFR 1114.3 - Admissibility of business records.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 8 2010-10-01 2010-10-01 false Admissibility of business records. 1114.3 Section... § 1114.3 Admissibility of business records. Any writing or record, whether in the form of an entry in a... be admissible as evidence thereof if it appears that it was made in the regular course of...

  10. 49 CFR 1114.3 - Admissibility of business records.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 8 2012-10-01 2012-10-01 false Admissibility of business records. 1114.3 Section... § 1114.3 Admissibility of business records. Any writing or record, whether in the form of an entry in a... be admissible as evidence thereof if it appears that it was made in the regular course of...

  11. 42 CFR 456.122 - Evaluation criteria for admission review.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Evaluation criteria for admission review. 456.122...: Review of Need for Admission 1 § 456.122 Evaluation criteria for admission review. The UR plan must provide that— (a) The committee develops written medical care criteria to assess the need for...

  12. Assisted living nursing practice: admission assessment.

    PubMed

    Mitty, Ethel; Flores, Sandi

    2007-01-01

    Admission assessment, generally conducted by a registered nurse, is autonomous, without opportunity for dialogue with colleagues and other health care professionals and bounded by the nurse's knowledge and skills, state regulations, facility practices, and marketing. The fact that some states permit admission and retention of nursing home level-of-care residents and provision of end-of-life care means that the assessment has to be able to predict the resident's likely trajectory of well-being as well as chronic illness exacerbation. The nurse must have a clear perspective on staff competencies and judge whether additional education or training will be necessary. This article reviews assessment standards of practice as put forth by the American Assisted Living Nurses Association as part of its application for recognition of assisted living nursing as specialty nursing practice by the American Nurses Association. The role of the Licensed Practical Nurse/Licensed Vocational Nurse in resident assessment is also discussed.

  13. Lasers, the Price of Admission in 2045

    DTIC Science & Technology

    2015-04-01

    altitude. Water vapor, pollutants , and other particles in the air , which are more prevalent at lower altitudes, cause absorption and scattering. These...AU/ACSC/DAYTON, J/AY15 AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY LASERS, THE PRICE OF ADMISSION IN 2045 by John G. Dayton, Maj, USAF...the Degree of MASTER OF OPERATIONAL ARTS AND SCIENCE Advisors: Lt Col Paul P. Clemans, Maj Thomas E. Kiesling Maxwell Air Force Base, Alabama

  14. Advanced development of the Spectrum Sciences Model 5005-TF, single event test fixture

    NASA Astrophysics Data System (ADS)

    Ackermann, M. R.; Browning, J. S.; Hughlock, B. W.; Lum, G. K.; Tsacoyeanes, W. C.; Weeks, M. D.

    A commercial application of particle identification methods commonly used in high-energy physics research has been developed for single-event testing of microelectronics. The Model 5005-TF single event test fixture can be used to substantially reduce the parts qualification testing costs for many space satellite systems. The 5005-TF includes a californium source, photomultiplier tubes, ultra thin film scintillation detectors, mountings, a vacuum chamber and related controls, and electronics for processing time-of-flight (TOF) signals. Tests were conducted to examine how well the TOF parameter identified the fission fragment (atomic number, mass, kinetic energy). For the lighter fragments, the TOF parameter has a maximum error of about 30 atomic mass units, which is inadequate for particle identification. Since light output of thin-film scintillators was known to correlate with average velocity of a fission fragment passing through the scintillator, it was decided to use the light output in conjunction with TOF to improve particle identification. This dual-parameter method was implemented in the 5005-TF and test results show favorable comparison with results from an ion beam facility.

  15. High temperature performance of nickel aluminide castings for furnace fixtures and components

    SciTech Connect

    Orth, J.E.; Sikka, V.K.

    1996-10-01

    Materials are often the key to technological advancement. To remain competitive and create new markets, modern heat treating industries must utilize these technological advances to increase production and process efficiencies. These challenges are frequently met by increasing process temperatures and minimizing down time for maintenance and unscheduled repairs. This requirement has frequently been a challenge in the past since an increase in the process temperature typically results in a decrease in the life of the furnace fixtures and components. Nickel aluminide intermetallic alloys, based on the Ni{sub 3}Al composition and structure, are a new class of materials for use in the heat treating industries. These alloys provide excellent strength at elevated temperatures combined with very good resistance to carburization (in reducing and oxidizing environments) and high temperature oxidation. The mechanical and physical properties of cast nickel aluminide alloys are presented and compared to other commercially available cast and wrought heat resistant alloys. The advances in the development of these alloys are also discussed.

  16. Chemical characterization of blue stains in domestic fixtures in contact with drinking water.

    PubMed

    Letelier, María V; Lagos, Gustavo E; Reyes, Arturo

    2008-04-01

    Bluish green staining in domestic fixtures was observed in three to 9-year-old houses in the city of Talca, located 256 km. south of Santiago, the capital of Chile. The houses contained copper pipes which were exposed to soft well water, with low pH and low buffer capacity. The aim of this paper is to establish the chemical composition of the stains and to determine the conditions by which they were formed. X-ray diffraction analysis of the stains revealed the presence of malachite, a copper compound that caused green coloring in kettles and water boilers. Dioptase, which is deep green in coloring, was identified in a bathtub tile. In one house, where blue stains were found in a toilet bowl, the presence of chrysocolla was suggested by means of X-ray fluorescence. In the field conditions studied it was concluded that the bluish green stains in bathroom home appliances were generated by the precipitation of copper compounds in places were leakages occur.

  17. Local Flow Conditions for Propulsion Experiments on the NASA F-15B Propulsion Flight Test Fixture

    NASA Technical Reports Server (NTRS)

    Vachon, Michael J.; Moes, Timothy R.; Corda, Stephen

    2005-01-01

    Local flow conditions were measured underneath the National Aeronautics and Space Administration F-15B airplane to support development of future experiments on the Propulsion Flight Test Fixture (PFTF). The local Mach number and flow angles were measured using a conventional air data boom on a cone-cylinder mounted under the PFTF and compared with the airplane air data nose boom measurements. At subsonic flight speeds, the airplane and PFTF Mach numbers were approximately equal. Transonic Mach number values were up to 0.1 greater at the PFTF than the airplane, which is a counterintuitive result. The PFTF local supersonic Mach numbers were as much as 0.46 less than the airplane values. The maximum local Mach number at the PFTF was approximately 1.6 at an airplane Mach number near 2.0. The PFTF local angle of attack was negative at all Mach numbers, ranging from -3 to -8 degrees. When the airplane angle of sideslip was zero, the PFTF local value was zero between Mach 0.8 and Mach 1.1, -2 degrees between Mach 1.1 and Mach 1.5, and increased from zero to 1 degree from Mach 1.5 to Mach 2.0. Airplane inlet shock waves crossed the aerodynamic interface plane between Mach 1.85 and Mach 1.90.

  18. A finite element model to predict the sound attenuation of earplugs in an acoustical test fixture.

    PubMed

    Viallet, Guilhem; Sgard, Franck; Laville, Frédéric; Boutin, Jérôme

    2014-09-01

    Acoustical test fixtures (ATFs) are currently used to measure the attenuation of the earplugs. Several authors pointed out that the presence of an artificial skin layer inside the cylindrical ear canal of the ATFs strongly influenced the attenuation measurements. In this paper, this role is investigated via a 2D axisymmetric finite element model of a silicon earplug coupled to an artificial skin. The model is solved using COMSOL Multiphysics (COMSOL(®), Sweden) and validated experimentally. The model is exploited thereafter to better understand the role of each part of the earplug/ear canal system and how the energy circulates within the domains. This is investigated by calculating power balances and by representing the mechanical and acoustical fluxes in the system. The important dissipative role of the artificial skin is underlined and its contribution as a sound transmission pathway is quantified. In addition, the influence of both the earplug and the artificial skin parameters is assessed via sensitivities analyses performed on the model.

  19. A test of the rotation handling fixture and altitude chamber in the O&C high bay

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Viewed from inside the altitude chamber in the Operations and Checkout Building's high bay, the Rotation Handling Fixture (RHF), with a simulated module attached, is lowered during a test. Under normal operation, the RHF will hold a pressurized module intended for the International Space Station, depositing it into the altitude chamber for leak testing. The chamber was recently reactivated after a 24-year hiatus. Originally, two chambers were built to test Apollo Program flight hardware. They were last used in 1975 during the Apollo-Soyuz Test Project. In 1997, in order to increase the probability of successful missions aboard the ISS, NASA decided to perform leak tests on ISS pressurized modules at the launch site. After installation of new vacuum pumping equipment and controls, a new control room, and a new rotation and handling fixture, the chamber again became operational in February 1999. The chamber, which is 33 feet in diameter and 50 feet tall, is constructed of stainless steel. The rotation handling fixture is aluminum. The first module that will be tested for leaks is the U.S. Laboratory. No date has been determined for the test.

  20. A test of the rotation handling fixture and altitude chamber in the O&C high bay

    NASA Technical Reports Server (NTRS)

    1999-01-01

    In the Operations and Checkout Building's high bay, the Rotation Handling Fixture (RHF), with a simulated module attached, is viewed from above the altitude chamber into which it was lowered during a test. Under normal operation, the RHF will hold a pressurized module intended for the International Space Station, depositing it into the altitude chamber for leak testing. The chamber was recently reactivated after a 20-year hiatus. Originally, two chambers were built to test Apollo Program flight hardware. They were last used in 1975 during the Apollo-Soyuz Test Project. In 1997, in order to increase the probability of successful missions aboard the ISS, NASA decided to perform leak tests on ISS pressurized modules at the launch site. After installation of new vacuum pumping equipment and controls, a new control room, and a new rotation and handling fixture, the chamber again became operational in February 1999. The chamber, which is 33 feet in diameter and 50 feet tall, is constructed of stainless steel. The rotation handling fixture is aluminum. The first module that will be tested for leaks is the U.S. Laboratory. No date has been determined for the test.

  1. A test of the rotation handling fixture and altitude chamber in the O&C high bay

    NASA Technical Reports Server (NTRS)

    1999-01-01

    In the Operations and Checkout Building's high bay, the Rotation Handling Fixture (RHF), with a simulated module attached, is lowered by crane into the altitude chamber below during a test. Under normal operation, the RHF will hold a pressurized module intended for the International Space Station, depositing it into the altitude chamber for leak testing. The chamber was recently reactivated after a 24-year hiatus. Originally, two chambers were built to test Apollo Program flight hardware. They were last used in 1975 during the Apollo-Soyuz Test Project. In 1997, in order to increase the probability of successful missions aboard the ISS, NASA decided to perform leak tests on ISS pressurized modules at the launch site. After installation of new vacuum pumping equipment and controls, a new control room, and a new rotation and handling fixture, the chamber again became operational in February 1999. The chamber, which is 33 feet in diameter and 50 feet tall, is constructed of stainless steel. The rotation handling fixture is aluminum. The first module that will be tested for leaks is the U.S. Laboratory. No date has been determined for the test.

  2. A test of the rotation handling fixture and altitude chamber in the O&C high bay

    NASA Technical Reports Server (NTRS)

    1999-01-01

    In the Operations and Checkout Building's high bay, a crane lifts the Rotation Handling Fixture (RHF) and simulated module during a test. Under normal operation, the RHF will hold a pressurized module intended for the International Space Station, lifting it up and into an altitude chamber for leak testing. The chamber was recently reactivated after a 24-year hiatus. Originally, two chambers were built to test Apollo Program flight hardware. They were last used in 1975 during the Apollo-Soyuz Test Project. In 1997, in order to increase the probability of successful missions aboard the ISS, NASA decided to perform leak tests on ISS pressurized modules at the launch site. After installation of new vacuum pumping equipment and controls, a new control room, and a new rotation and handling fixture, the chamber again became operational in February 1999. The chamber, which is 33 feet in diameter and 50 feet tall, is constructed of stainless steel. The rotation handling fixture is aluminum. The first module that will be tested for leaks is the U.S. Laboratory. No date has been determined for the test.

  3. Characteristics of delayed admission to stroke unit.

    PubMed

    Silvestrelli, Giorgio; Parnetti, Lucilla; Tambasco, Nicola; Corea, Francesco; Capocchi, Giuseppe

    2006-01-01

    Early admission to stroke unit (SU) and factors that may cause admission delay represent relevant issues to obtain an optimal management of acute stroke. This study was aimed at recording timing from clinical onset to admission to our SU and to identify the reasons for delay. We prospectively examined acute stroke patients consecutively admitted to the Perugia SU. Baseline characteristics of stroke patients, stroke type and etiology, time from symptom onset to arrival in the SU were obtained from the Hospital-Based Perugia Stroke Registry. 60.8% of 2,213 consecutive stroke patients admitted to the SU arrived within 6 hrs and 39.2% after 6 hrs. Underestimation of symptoms was the cause of delay in 48.7% of cases. Younger age, especially for females, ischemic stroke, mild and/or unspecific symptoms and the underestimation of symptoms seem to be the main reasons for delayed arrival in the SU. To increase the proportion of stroke patients arriving in the SU within 3 hr of symptom onset, it is necessary to improve public and general practitioner awareness of stroke through educational programs.

  4. Complexity in College Admission: Fact or Urban Myth. Research Findings of Parent and Student Perceptions of Complexity in College Admission

    ERIC Educational Resources Information Center

    College Board Advocacy & Policy Center, 2010

    2010-01-01

    In September 2007, the College Board formed the Task Force on Admissions in the 21st Century in response to a request from the Guidance and Admission Assembly Council (GAA Council) to more closely examine the high-school-to-college transition process. Each spring, at the conclusion of the college admission cycle, there is much discussion in the…

  5. A Role for Marketing in College Admissions. Papers Presented at the Colloquium on College Admissions, May 16-l8, 1976.

    ERIC Educational Resources Information Center

    College Entrance Examination Board, New York, NY.

    This collection stresses the need for informed and more sophisticated marketing techniques for college admissions officers to help them cope with the decreasing number of prospective college students. The importance of the college admissions office is increasing as admissions becomes a more crucial element to the colleges' financial well-being.…

  6. Effects of the Economy on the Admission Process: 2008-09. National Association for College Admission Counseling, September 2009

    ERIC Educational Resources Information Center

    National Association for College Admission Counseling, 2009

    2009-01-01

    The 2008-09 college admission cycle took place during a period of heightened economic uncertainty. When added to the annual uncertainty of the admission process--for both students seeking college admission offers and colleges seeking to predict their annual enrollment yield--the economic environment caused great concern among colleges and students…

  7. Admission Requirements for Transfer and Non-Transfer Students: Should One Size Fit All?

    ERIC Educational Resources Information Center

    Pharr, Steven; Lawrence, John J.

    2007-01-01

    Purpose: To examine the efficacy of admission requirements as predictors of academic success in core business coursework, and as a rationing mechanism for limited course capacity, for both transfer and non-transfer students following integration of the core business curriculum. Design/methodology/approach: Regression analysis is used to test the…

  8. Reductions in hospital admissions and mortality rates observed after integrating emergency care: a natural experiment

    PubMed Central

    Ahmed, Vazeer; Palmer, Christopher R; Bennett, Tom J H; Robinson, Susan M

    2012-01-01

    Objectives Reducing emergency admissions is a priority for the NHS. A single hospital's emergency care system was reorganised with the principles of front-loaded investigations, integration of specialties, reduced duplication, earlier decision making by senior clinicians and a combined emergency assessment area. The authors relocated our Medical Assessment Unit into our emergency department in 2006. The authors evaluated changes in admissions and mortality before and after 2006, compared with other similar hospitals. Design Quasi-experimental before and after study using routinely collected data. Setting and participants 1 acute hospital in England, the intervention site, was compared with 23 other English hospitals between 2001 and 2009. Outcome measures Our outcome measures were hospital standardised mortality ratios (HSMRs) for non-elective admissions and standardised admission ratios (SARs). Results The authors observed a statistically and clinically significant decrease in HSMR and SAR. The intervention hospital had the lowest HSMR and SAR of all the hospitals in our sample. This was statistically significant, p=0.0149 and p=0.0002, respectively. Conclusion Integrating emergency care in one location is associated with a meaningful reduction in mortality and emergency admissions to hospital. PMID:22858459

  9. Evaluation of a single cell and candidate materials with high water content hydrogen in a generic solid oxide fuel cell stack test fixture, Part II: materials and interface characterization

    SciTech Connect

    Chou, Y. S.; Stevenson, Jeffry W.; Choi, Jung-Pyung

    2013-01-01

    A generic solid oxide fuel cell (SOFC) test fixture was developed to evaluate candidate materials under realistic conditions. A commerical 50 mm x 50 mm NiO-YSZ anode supported thin YSZ electrolyte cell with lanthanum strontium manganite (LSM) cathode was tested to evaluate the stability of candidate materials. The cell was tested in two stages at 800oC: stage I of low (~3% H2O) humidity and stage II of high (~30% H2O) humidity hydrogen fuel at constant voltage or constant current mode. Part I of the work was published earlier with information of the generic test fixture design, materials, cell performance, and optical post-mortem analysis. In part II, detailed microstructure and interfacial characterizations are reported regarding the SOFC candidate materials: (Mn,Co)-spinel conductive coating, alumina coating for sealing area, ferritic stainless steel interconnect, refractory sealing glass, and their interactions with each other. Overall, the (Mn,Co)-spinel coating was very effective in minimizing Cr migration. No Cr was identified in the cathode after 1720h at 800oC. Aluminization of metallic interconnect also proved to be chemically compatible with alkaline-earth silicate sealing glass. The details of interfacial reaction and microstructure development are discussed.

  10. Does a home treatment acute relapse prevention strategy reduce admissions for people with mania in bipolar affective disorder?

    PubMed Central

    Murton, Claudia; Cooper, Michael; Dinniss, Stephen; Roberts, Shon; Booth, Nicola; Newell, Paul

    2014-01-01

    Aims and method To assess whether a home treatment team acute relapse prevention (ARP) strategy reduces admissions to hospital with mania. A retrospective design was used to analyse records for manic admissions since 2002. The number and length of admissions and detentions pre- and post-ARP were determined and rates of admissions and detentions calculated from this. Results We found reductions in admission and detention rates following the introduction of the ARP: 0.3 fewer admissions per person per year (95% bootstrap CI 0.09–0.62) and 0.25 fewer detentions per person per year (95% bootstrap CI 0.0–0.48). Wilcoxon signed-rank tests gave P<0.0001. Clinical implications A person-centred care plan such as the ARP which enables quick action in response to relapse-warning signs of mania appears to reduce rates of admission to hospital. The ARP could be used anywhere in the UK and fits with current mental health policy. PMID:25505627

  11. Tracing the Effects of Guaranteed Admission through the College Process: Regression Discontinuity Evidence from the Texas 10% Plan◆

    PubMed Central

    Fletcher, Jason M.; Mayer, Adalbert

    2012-01-01

    The Texas 10% law states that students who graduated among the top 10% of their high school class are guaranteed admission to public universities in Texas. We estimate the causal effects of this admissions guarantee on a sequence of connected decisions: students’ application behavior, admission decisions by the university, students’ enrollment choices conditional on admission; as well as the resulting college achievement. We identify these effects by comparing students just above and just below the top 10% rank cutoff. While this design is in the spirit of a regression discontinuity, we note important differences in approach and interpretation. We find that students react to incentives created by the admissions guarantee - for example, by reducing applications to competing private universities. The results also suggest that the effects of the admissions guarantee depend on the university and the type of students it attracts, and that the law is binding and alters the decisions of the admissions committees. We find little evidence that the law increases diversity or leads to meaningful mismatch for the marginal student admitted. PMID:24610997

  12. Promoting plumbing fixture and fitting replacement: Recommendations and review for state and local water resource authorities

    SciTech Connect

    Dunham, C.; Lutz, J.D.; Pickle, S.J.

    1995-06-01

    Lawrence Berkeley National Laboratory (LBNL) has prepared this report to facilitate compliance with the requirements of Section 123 of the Energy Policy Act of 1992 (EPACT). Section 123 requires the Department of Energy to issue recommendations for establishing state and local incentive programs to encourage acceleration of voluntary consumer replacement of existing water closets, urinals, showerheads and faucets with water-saving products meeting EPACT standards. The authors recommend that state and local authorities working together and also with utilities: (A) investigate the cost-effectiveness of voluntary replacement of plumbing fixtures and fittings as an effective component of a water efficiency incentive program; (B) allow utilities to distribute the costs of water saving products by billing at pre-installation rates until devices have been paid for; (C) encourage decreased water usage by establishing rate structures such as increasing block rates or seasonal pricing; (D) add additional incentive to rebate programs by making the rebates untaxable income. (E) require municipalities or utilities to exhaust every reasonable method of water conservation before applying for permits to construct water supply or water treatment systems; (F) require high-efficiency toilets, urinals, showerheads, and faucets in new construction and changing plumbing codes to incorporate different pipe sizing needs; and (G) and mandate installation of meters to correctly measure water consumption. Following the introduction, a general overview of these recommendations is presented. Each recommendation is discussed briefly. After determining the cost-effectiveness of a plumbing replacement program (or plumbing replacement aspect of a larger program) states can encourage replacement of toilets, urinals, showerheads, and faucets in a number of ways. This report lists both legislative and economic measures that can be implemented on the state level that impact local programs.

  13. Wavelet frames and admissibility in higher dimensions

    NASA Astrophysics Data System (ADS)

    Führ, Hartmut

    1996-12-01

    This paper is concerned with the relations between discrete and continuous wavelet transforms on k-dimensional Euclidean space. We start with the construction of continuous wavelet transforms with the help of square-integrable representations of certain semidirect products, thereby generalizing results of Bernier and Taylor. We then turn to frames of L2(Rk) and to the question, when the functions occurring in a given frame are admissible for a given continuous wavelet transform. For certain frames we give a characterization which generalizes a result of Daubechies to higher dimensions.

  14. Optical Alignment of the JWST ISIM to the OTE Simulator (OSIM): Current Concept and Design Studies

    NASA Technical Reports Server (NTRS)

    Frey, Bradley J.; Davila, Pamela S.; Marsh, James M.; Ohl, Raymond G.; Sullivan, Joseph

    2007-01-01

    The James Webb Space Telescope's (JWST) Integrated Science Instrument Module (ISIM) is the scientific payload of the observatory and contai ns four science instruments. During alignment and test of the integrated ISIM (i.e. ISIM + science instruments) at NASA's Goddard Space Fli ght Center (GSFC), the Optical telescope element SIMulator (OSIM) wil l be used to optically stimulate the science instruments to verify their operation and performance. In this paper we present the design of two cryogenic alignment fixtures that will be used to determine and verify the proper alignment of OSIM to ISIM during testing at GSFC. The se fixtures, the Master Alignment Target Fixture (MATF) and the ISIM Alignment Target Fixture (IATF), will provide continuous, 6 degree of freedom feedback to OSIM during initial ambient alignment as well as during cryogenic vacuum testing.

  15. Development of a Maximum Admissions Index for Freshman Admissions to the University of Washington.

    ERIC Educational Resources Information Center

    Lunneborg, Clifford E.

    A new technique has been developed for admitting new freshman students at the University of Washington. Previously, an Admissions Index (AI) was used, in which the high school grade point average (HSGPA) was assigned twice the weight of the composite verbal and quantitative scores from the Washington Pre-College Test Battery (WPC). To offset the…

  16. An Evaluation of the Pharmacy College Admissions Test as a Tool for Pharmacy College Admissions Committees.

    ERIC Educational Resources Information Center

    Kelley, Katherine A.; Secnik, Kristina; Boye, Mark E.

    2001-01-01

    Investigated the capacity of the Pharmacy College Admissions Test (PCAT) to predict success in pharmacy school. Found demographic differences in PCAT scores, and that the PCAT used in combination with pre-pharmacy grade point average is meaningful in assessing applicants to pharmacy school; applicants with PCAT composite percentile scores below 40…

  17. Challenges in College Admissions. A Report of a Survey of Undergraduate Admissions Policies, Practices, and Procedures.

    ERIC Educational Resources Information Center

    Breland, Hunter M.; And Others

    The report summarizes undergraduate admissions policies, practices, and procedures at two- and four-year colleges and universities as of 1992. Information was drawn from a national survey, the third of a series conducted since 1979. A total of 2,024 institutions responded to the survey. An introductory chapter describes the surveys, their…

  18. Students Selection for University Course Admission at the Joint Admissions Board (Kenya) Using Trained Neural Networks

    ERIC Educational Resources Information Center

    Wabwoba, Franklin; Mwakondo, Fullgence M.

    2011-01-01

    Every year, the Joint Admission Board (JAB) is tasked to determine those students who are expected to join various Kenyan public universities under the government sponsorship scheme. This exercise is usually extensive because of the large number of qualified students compared to the very limited number of slots at various institutions and the…

  19. Psychological implications of admission to critical care.

    PubMed

    Pattison, Natalie

    Admission to critical care can have far-reaching psychological effects because of the distinct environment. Critical care services are being re-shaped to address long-term sequelae, including post-traumatic stress disorder, anxiety and depression. The long-term consequences of critical illness not only cost the individual, but also have implications for society, such as diminished areas of health-related quality-of-life in sleep, reduced ability to return to work and enjoy recreational activities (Audit Commission, 1999; Hayes et al, 2000). The debate around the phenomenon of intensive care unit (ICU) syndrome is discussed with reference to current thinking. After critical care, patients may experience amnesia, continued hallucinations or flashbacks, anxiety, depression, and dreams and nightmares. Nursing care for patients while in the critical care environment can have a positive effect on psychological well-being. Facilitating communication, explaining care and rationalizing interventions, ensuring patients are oriented as to time and place, reassuring patients about transfer, providing patients,where possible, with information about critical care before admission and considering anxiolytic use, are all practices that have a beneficial effect on patient care. Follow-up services can help patients come to terms with their experiences of critical illness and provide the opportunity for them to access further intervention if desired. Working towards providing optimal psychological care will have a positive effect on patients' psychological recovery and may also help physical recuperation after critical care.

  20. Loneliness and nursing home admission among rural older adults.

    PubMed

    Russell, D W; Cutrona, C E; de la Mora, A; Wallace, R B

    1997-12-01

    In this study, the authors tested the relation between loneliness and subsequent admission to a nursing home over a 4-year time period in a sample of approximately 3,000 rural older Iowans. Higher levels of loneliness were found to increase the likelihood of nursing home admission and to decrease the time until nursing home admission. The influence of extremely high loneliness on nursing home admission remained statistically significant after controlling for other variables, such as age, education, income, mental status, physical health, morale, and social contact, that were also predictive of nursing home admission. Several mechanisms are proposed to explain the link between extreme loneliness and nursing home admission. These include loneliness as a precipitant of declines in mental and physical health and nursing home placement as a strategy to gain social contact with others. Implications for preventative interventions are discussed.

  1. Unplanned admissions and the organisational management of heart failure: a multicentre ethnographic, qualitative study

    PubMed Central

    Simmonds, Rosemary; Glogowska, Margaret; McLachlan, Sarah; Cramer, Helen; Sanders, Tom; Johnson, Rachel; Kadam, Umesh; Lasserson, Daniel; Purdy, Sarah

    2015-01-01

    Objectives Heart failure is a common cause of unplanned hospital admissions but there is little evidence on why, despite evidence-based interventions, admissions occur. This study aimed to identify critical points on patient pathways where risk of admission is increased and identify barriers to the implementation of evidence-based interventions. Design Multicentre, longitudinal, patient-led ethnography. Setting National Health Service settings across primary, community and secondary care in three geographical locations in England, UK. Participants 31 patients with severe or difficult to manage heart failure followed for up to 11 months; 9 carers; 55 healthcare professionals. Results Fragmentation of healthcare, inequitable provision of services and poor continuity of care presented barriers to interventions for heart failure. Critical points where a reduction in the risk of current or future admission occurred throughout the pathway. At the beginning some patients did not receive a formal clinical diagnosis, in addition patients lacked information about heart failure, self-care and knowing when to seek help. Some clinicians lacked knowledge about diagnosis and management. Misdiagnoses of symptoms and discontinuity of care resulted in unplanned admissions. Approaching end of life, patients were admitted to hospital when other options including palliative care could have been appropriate. Conclusions Findings illustrate the complexity involved in caring for people with heart failure. Fragmented healthcare and discontinuity of care added complexity and increased the likelihood of suboptimal management and unplanned admissions. Diagnosis and disclosure is a vital first step for the patient in a journey of acceptance and learning to self-care/monitor. The need for clinician education about heart failure and specialist services was acknowledged. Patient education should be seen as an ongoing ‘conversation’ with trusted clinicians and end-of-life planning should be

  2. Heat-related respiratory hospital admissions in Europe in a changing climate: a health impact assessment

    PubMed Central

    Åström, Christofer; Orru, Hans; Rocklöv, Joacim; Strandberg, Gustav; Ebi, Kristie L; Forsberg, Bertil

    2013-01-01

    Objectives Respiratory diseases are ranked second in Europe in terms of mortality, prevalence and costs. Studies have shown that extreme heat has a large impact on mortality and morbidity, with a large relative increase for respiratory diseases. Expected increases in mean temperature and the number of extreme heat events over the coming decades due to climate change raise questions about the possible health impacts. We assess the number of heat-related respiratory hospital admissions in a future with a different climate. Design A Europe-wide health impact assessment. Setting An assessment for each of the EU27 countries. Methods Heat-related hospital admissions under a changing climate are projected using multicity epidemiological exposure–response relationships applied to gridded population data and country-specific baseline respiratory hospital admission rates. Times-series of temperatures are simulated with a regional climate model based on four global climate models, under two greenhouse gas emission scenarios. Results Between a reference period (1981–2010) and a future period (2021–2050), the total number of respiratory hospital admissions attributed to heat is projected to be larger in southern Europe, with three times more heat attributed respiratory hospital admissions in the future period. The smallest change was estimated in Eastern Europe with about a twofold increase. For all of Europe, the number of heat-related respiratory hospital admissions is projected to be 26 000 annually in the future period compared with 11 000 in the reference period. Conclusions The results suggest that the projected effects of climate change on temperature and the number of extreme heat events could substantially influence respiratory morbidity across Europe. PMID:23355662

  3. Underrepresented Minorities in Medical School Admissions: A Qualitative Study.

    PubMed

    Hadinger, Margaret A

    2017-01-01

    Phenomenon: This study explored Black/African American and Hispanic/Latino medical students' perceptions of the medical school admissions process. Previous research has explored other elements of the medical education continuum. However, little is known regarding minorities' perceptions of navigating the medical school admissions process. To address this gap in the literature, this exploratory study suggests a conceptual model describing why minorities apply to medical school and the influences affecting their admissions experience.

  4. Accuracy of caregivers’ recall of hospital admissions: implications for research

    PubMed Central

    Burakevych, Nataliia; McKinlay, Christopher Joel Dorman; Alsweiler, Jane Marie; Harding, Jane Elizabeth

    2015-01-01

    Aim To determine the accuracy of caregivers’ recall of hospital admissions in early childhood. Methods Prospective cohort study of babies born at risk of neonatal hypoglycaemia at Waikato Hospital, New Zealand, a regional public hospital and sole provider of acute inpatient care to over 100,000 children. Caregivers’ recall of children’s hospital admissions up to 4.5 years were compared with medical records. Accuracy of recall was related to neonatal and socio-demographic characteristics. Results Out of 267 children, 179 (67%) visited hospital and 106 (40%) were admitted at least once. The most frequent reasons for admission were for respiratory (29%) and gastrointestinal (18%) problems. Of 106 children admitted to hospital, 27 (25%) caregivers did not recall the admission and only 37 (35%) accurately recalled the number of admissions. The accuracy of recall was lower for gastrointestinal (38%) and surgical (40%) problems, while recall of respiratory (64%) and ear, nose and throat (60%) admissions was more accurate. Low socio-economic status and multiple admissions were associated with less accurate recall of number of admissions. Conclusion Caregivers do not accurately report hospital admissions. Questionnaire data about use of hospital facilities should be interpreted cautiously, and may not be sufficiently accurate for use in research studies. PMID:26355393

  5. Dynamic virtual fixture on the Euclidean group for admittance-type manipulator in deforming environments

    PubMed Central

    2014-01-01

    Background In a deforming anatomic environment, the motion of an instrument suffers from complex geometrical and dynamic constraints, robot assisted minimally invasive surgery therefore requires more sophisticated skills for surgeons. This paper proposes a novel dynamic virtual fixture (DVF) to enhance the surgical operation accuracy of admittance-type medical robotics in the deforming environment. Methods A framework for DVF on the Euclidean Group SE(3) is presented, which unites rotation and translation in a compact form. First, we constructed the holonomic/non-holonomic constraints, and then searched for the corresponded reference to make a distinction between preferred and non-preferred directions. Second, different control strategies are employed to deal with the tasks along the distinguished directions. The desired spatial compliance matrix is synthesized from an allowable motion screw set to filter out the task unrelated components from manual input, the operator has complete control over the preferred directions; while the relative motion between the surgical instrument and the anatomy structures is actively tracked and cancelled, the deviation relative to the reference is compensated jointly by the operator and DVF controllers. The operator, haptic device, admittance-type proxy and virtual deforming environment are involved in a hardware-in-the-loop experiment, human-robot cooperation with the assistance of DVF controller is carried out on a deforming sphere to simulate beating heart surgery, performance of the proposed DVF on admittance-type proxy is evaluated, and both human factors and control parameters are analyzed. Results The DVF can improve the dynamic properties of human-robot cooperation in a low-frequency (0 ~ 40 rad/sec) deforming environment, and maintain synergy of orientation and translation during the operation. Statistical analysis reveals that the operator has intuitive control over the preferred directions, human and the DVF

  6. The surgical admissions proforma: Does it make a difference?

    PubMed

    Ehsanullah, Jasmine; Ahmad, Umar; Solanki, Kohmal; Healy, Justin; Kadoglou, Naim

    2015-03-01

    Admissions records are essential in communicating key information regarding unwell patients and at handover of care. We designed, implemented and evaluated the impact of a standardised surgical clerking proforma on documentation and clinician acceptability in comparison to freehand clerking. A clerking proforma was implemented for all acute general surgical admissions. Documentation was assessed according to 32 criteria based on the Royal College of Surgeons of England guidelines, for admissions before (n = 72) and after (n = 96) implementation. Fisher's exact test and regression analysis were used to compare groups. Surgical team members were surveyed regarding attitudes towards the new proforma. Proforma uptake was 73%. After implementation, documentation increased in 28/32 criteria. This was statistically significant in 17 criteria, including past surgical history (p < 0.01), medication history (p = 0.03), ADLs (p = 0.02), systems review (p < 0.01), blood pressure (p < 0.01), blood results (p = 0.02) and advice given to the patient (p = 0.02). The proforma remained beneficial after regression analysis accounted for differences in time of day, seniority of the doctor and nights or weekends (coefficient = 0.12 [p < 0.01]). 89% of the surgical team felt the form improved quality of documentation and preferred its use to freehand clerking. 94% felt it was beneficial on the post-take ward-round. Audit quality control was also more reliable with the proforma (inter-observer agreement = 99.3% [κ = 0.997]) versus freehand clerking (97.1% [κ = 0.941]). Our study demonstrates that a standardised surgical clerking proformas improves the quantity and quality of documentation in comparison to freehand clerking, is preferred by health professionals and improves reliability of the audit quality control process.

  7. Hospital admissions among male drivers in Denmark

    PubMed Central

    Hannerz, H; Tuchsen, F

    2001-01-01

    OBJECTIVES—To facilitate decisions about interventions and to establish baseline values for future evaluation of preventive efforts, the aim of the present study was to elucidate the disease pattern among male professional drivers in Denmark. The study differentiated between drivers of goods vehicles and drivers of passenger transport.
METHODS—Cohorts of all 20-59 year old Danish male professional drivers in the years 1981, 1986, 1991, and 1994 were formed, to calculate age standardised hospital admission ratios (SHRs) and time trends (1981-97) for many diagnostic aggregations.
RESULTS—SHRs for diseases in practically all systems and organs of the body were higher among professional drivers than they were in the male working population at large. Also drivers of passenger transport, compared with drivers of goods vehicles, had significantly high SHRs due to infectious and parasitic diseases, diseases of the circulatory system, and diseases of the respiratory system, and significantly lower rates of injury. For both driver groups, the SHRs for acute myocardial infarction increased with time whereas the SHR for acute gastritis decreased, and for drivers of passenger transport an increasing SHR for chronic obstructive pulmonary disease, was found over time.
CONCLUSION—Drivers of passenger transport and drivers of goods vehicles differ in their disease patterns. The results support the hypothesis that preventive efforts are needed in both groups, but underline that different strategies are required for different categories of drivers.


Keywords: professional drivers; hospital admissions; surveillance system PMID:11245742

  8. EFFECT OF RADIUS OF LOADING NOSE AND SUPPORTS IN SHORT BEAM TEST FIXTURE ON FRACTURE MODE AND INTERLAMINAR SHEAR STRENGTH OF GFRP AT 77 K

    SciTech Connect

    Nishimura, A.

    2008-03-03

    A short beam test is useful to evaluate interlaminar shear strength of glass fiber reinforced plastics, especially for material selection. However, effect of test fixture configuration on interlaminar shear strength has not been clarified. This paper describes dependence of fracture mode and interlaminar shear strength on the fixture radius using the same materials and procedure. In addition, global understanding of the role of the fixture is discussed. When small loading nose and supports are used for the tests, bending fracture or translaminar fracture happens and the interlaminar shear strength would become smaller. By adopting the large radius loading nose and supports (6 mm radius is recommended), it is newly recognized that some stress concentration is able to be reduced, and the interlaminar fracture tends to occur and the other fracture modes will be suppressed. The interlaminar shear strength of 2.5 mm thick GFRP plate of G-10CR is evaluated as 130-150 MPa at 77 K.

  9. Gaseous Air Pollution and the Risk for Stroke Admissions: A Case-Crossover Study in Beijing, China

    PubMed Central

    Huang, Fangfang; Luo, Yanxia; Tan, Peng; Xu, Qin; Tao, Lixin; Guo, Jin; Zhang, Feng; Xie, Xueqin; Guo, Xiuhua

    2017-01-01

    Background: Though increasing evidence supports association between gaseous air pollution and stroke, it remains unclear whether the effects differ in season, sex and age. The aim of this study was to examine the associations of gaseous air pollution with stroke admissions in Beijing, 2013–2014 in different subgroups. Methods: Case-crossover design and conditional logistic regression were used to perform the analyses. We examined the exposure-response relationship between air pollution and stroke. Stratified analyses were performed in different seasons, sex, and age groups. Results: There were 147,624 stroke admissions during the study period. In the whole study period, percent changes of stroke admissions were 0.82% (95% CI: 0.52% to 1.13%) and 0.73% (95% CI: 0.44% to 1.03%) per 10 μg/m3 increase in the same day conentration of nitrogen dioxide (NO2) and sulfur dioxide (SO2). The positive associations were higher in warm seasons and with patients >65 years (p < 0.05). Contrary effects of carbon monoxide (CO) and ozone on stroke admissions were observed in different seasons. Conclusions: NO2 and SO2 were positively associated with stroke admissions, with stronger effects in warm seasons and with patients >65 years. The associations of CO and ozone with stroke admissions differed across seasons. PMID:28216595

  10. Finite element structural redesign by large admissible perturbations

    NASA Technical Reports Server (NTRS)

    Bernitsas, Michael M.; Beyko, E.; Rim, C. W.; Alzahabi, B.

    1991-01-01

    In structural redesign, two structural states are involved; the baseline (known) State S1 with unacceptable performance, and the objective (unknown) State S2 with given performance specifications. The difference between the two states in performance and design variables may be as high as 100 percent or more depending on the scale of the structure. A Perturbation Approach to Redesign (PAR) is presented to relate any two structural states S1 and S2 that are modeled by the same finite element model and represented by different values of the design variables. General perturbation equations are derived expressing implicitly the natural frequencies, dynamic modes, static deflections, static stresses, Euler buckling loads, and buckling modes of the objective S2 in terms of its performance specifications, and S1 data and Finite Element Analysis (FEA) results. Large Admissible Perturbation (LEAP) algorithms are implemented in code RESTRUCT to define the objective S2 incrementally without trial and error by postprocessing FEA results of S1 with no additional FEAs. Systematic numerical applications in redesign of a 10 element 48 degree of freedom (dof) beam, a 104 element 192 dof offshore tower, a 64 element 216 dof plate, and a 144 element 896 dof cylindrical shell show the accuracy, efficiency, and potential of PAR to find an objective state that may differ 100 percent from the baseline design.

  11. Alveolar regions of the mandible for the installation of immediate-implant fixtures and bone screws of alveolar distractors.

    PubMed

    Kim, Da-Hye; Park, Man-Soo; Won, Sung-Yoon; Hu, Kyung-Seok; Han, Dong-Hoo; Kim, Hee-Jin

    2011-05-01

    The purposes of this study were to elucidate the anatomic relationship between the dental roots and surrounding tissues and to identify the optimal sites at which to install dental surgical devices including immediate-implant fixtures and alveolar distractors. We made 5 types of measurements on horizontal cross sections obtained at 1-mm intervals from 20 Korean mandibles. The following results were obtained: (1) the mandibular facial plate was thinnest at the canine (0.5-0.7 mm) and became thicker toward the molar region; (2) the thicknesses of the facial and lingual cortical bone in the interdental region increased from anterior to posterior and from coronal to apical aspects; (3) in each section, the buccolingual root was narrower than 4 mm at depths greater than 8 and 9 mm in the central and lateral incisors, respectively, and the maximum mesiodistal root widths were 3.0 and 3.3 mm; (4) the interroot distance increased from anterior to posterior and from coronal to apical aspects; and (5) on the sections of the first and second molars, the diameter of the septal bone ranged from 4.2 to 7.9 mm buccolingually and from 1.3 to 3.3 mm mesiodistally. Achieving successful placements of implant fixtures and bone screws requires an accurate understanding of the anatomic structure at the installation site. The reported anatomic data might facilitate successful treatments and provide crucial information for use when planning and performing placements of dental surgical devices.

  12. Development of S-band antenna interface design, volume 1

    NASA Technical Reports Server (NTRS)

    Kuhlman, E. A.

    1976-01-01

    The construction of an analytical thermal model of an S-band antenna in a typical Space Shuttle Orbiter installation is discussed. The selection and modeling of orbital and entry thermal environment inputs for the thermal analyses are discussed. The results of analyses for a variety of orbital thermal environments and entry initial conditions are given. Design and fabrication details of a thermal test fixture which physically approximates the Orbiter installation are discussed. The design and fabrication of two electrical test fixtures which electrically simulate the Orbiter surface shape and thermal protection system are discussed.

  13. 28 CFR 54.305 - Preference in admission.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 54.305 Preference in admission. A recipient to... or predominantly members of one sex, if the giving of such preference has the effect...

  14. 14 CFR 1253.305 - Preference in admission.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1253.305 Preference in admission. A... students only or predominantly members of one sex, if the giving of such preference has the effect...

  15. The Confidence Game in Honors Admissions and Retention

    ERIC Educational Resources Information Center

    Guzy, Annmarie

    2013-01-01

    Annmarie Guzy, an expert with almost three decades of experience in post-secondary honors education, responds to Jerry Herron's essay, "Notes toward an Excellent Marxist-Elitist Honors Admissions Policy," which argues that "a well-conceived admissions policy tells us much more than whom to recruit; it becomes the basis for a…

  16. Evaluating the Predictive Validity of Graduate Management Admission Test Scores

    ERIC Educational Resources Information Center

    Sireci, Stephen G.; Talento-Miller, Eileen

    2006-01-01

    Admissions data and first-year grade point average (GPA) data from 11 graduate management schools were analyzed to evaluate the predictive validity of Graduate Management Admission Test[R] (GMAT[R]) scores and the extent to which predictive validity held across sex and race/ethnicity. The results indicated GMAT verbal and quantitative scores had…

  17. 6 CFR 17.305 - Preference in admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 17.305 Preference in admission. A recipient... only or predominantly members of one sex, if the giving of such preference has the effect...

  18. 14 CFR 1253.305 - Preference in admission.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and Recruitment Prohibited § 1253.305 Preference in admission. A... students only or predominantly members of one sex, if the giving of such preference has the effect...

  19. University Exceptional Admission during the Republic of China

    ERIC Educational Resources Information Center

    Tao, Li

    2014-01-01

    The stories of many universities' exceptive admission during the republic period of China were widely circulated. The typical example of these universities' exceptional admission was the very product of special historical condition, which had its own characteristics, but also conforms to the general rule, so it can be cited. To select special…

  20. Failure as a Criterion for Medical School Admission.

    ERIC Educational Resources Information Center

    Greer, David S.; Aronson, Stanley M.

    1980-01-01

    Admissions committees, it is suggested, should regard a failure experience as an opportunity to examine characteristics of candidates which may otherwise be inapparent. Current admissions criteria do not adequately address the social responsibilities and humanitarian goals of medical education. (Author/MLW)

  1. 14 CFR 125.315 - Admission to flight deck.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ...,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Operations § 125.315 Admission to flight deck. (a) No person may admit any person to the flight deck of an airplane unless the... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Admission to flight deck. 125.315...

  2. 14 CFR 125.315 - Admission to flight deck.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ...,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Operations § 125.315 Admission to flight deck. (a) No person may admit any person to the flight deck of an airplane unless the... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Admission to flight deck. 125.315...

  3. 14 CFR 125.315 - Admission to flight deck.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ...,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Operations § 125.315 Admission to flight deck. (a) No person may admit any person to the flight deck of an airplane unless the... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Admission to flight deck. 125.315...

  4. 14 CFR 125.315 - Admission to flight deck.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ...,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Operations § 125.315 Admission to flight deck. (a) No person may admit any person to the flight deck of an airplane unless the... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Admission to flight deck. 125.315...

  5. 14 CFR 125.315 - Admission to flight deck.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ...,000 POUNDS OR MORE; AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Flight Operations § 125.315 Admission to flight deck. (a) No person may admit any person to the flight deck of an airplane unless the... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Admission to flight deck. 125.315...

  6. 28 CFR 541.47 - Admission to control unit.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Admission to control unit. 541.47 Section... INMATE DISCIPLINE AND SPECIAL HOUSING UNITS Control Unit Programs § 541.47 Admission to control unit. Staff shall provide an inmate admitted to a control unit with: (a) Notice of the projected duration...

  7. The Admission and Induction of Refugee Children into School.

    ERIC Educational Resources Information Center

    Spafford, Tim; Bolloten, Bill

    1995-01-01

    Examines induction and admission practice for refugee school children into Britain's public schools, highlights the educational issues and concerns of newly-arrived refugee families, and discusses what schools can do to make their entry into the school system less problematic. The author explains how good admission and induction practices can…

  8. Environmental Scan of BC Post-Secondary Admissions: 2009

    ERIC Educational Resources Information Center

    Heath, Nick

    2009-01-01

    In 2008, British Columbia Council on Admissions and Transfer (BCCAT) commissioned an environmental scan on the possible need for system-wide work on institutional admissions processes and practices. This scan is intended to seek system input and to provide guidance on the choice of research projects and other related work in the coming year. This…

  9. Evaluating Admission Criteria Effects for Under-Represented Groups

    ERIC Educational Resources Information Center

    Childs, Ruth A.; Ferguson, Amanda K.; Herbert, Monique B.; Broad, Kathryn; Zhang, Jingshun

    2016-01-01

    The effects that admission criteria may have for under-represented groups are an important concern for programs seeking to improve access to post-secondary education. Using data from a large preservice teacher education program in the Canadian province of Ontario, we demonstrate two approaches to evaluating the effects of admission criteria. The…

  10. Strategic Enrollment Management's Ambassadors: The Changing Role of Admissions Counselors

    ERIC Educational Resources Information Center

    Mathis, Daniel

    2010-01-01

    Road runner. File jockey. Advisor. Public speaker. Recruiter. At any given time, an admissions counselor fits one, some, or all of these descriptors. While all of these descriptors indicate an important function within a college or university, none reflects the increasingly complex nature of the role of an admissions counselor in strategic…

  11. Disciplinary Logics in Doctoral Admissions: Understanding Patterns of Faculty Evaluation

    ERIC Educational Resources Information Center

    Posselt, Julie R.

    2015-01-01

    Ph.D. attainment rates by race and gender vary widely across the disciplines, and previous research has found disciplinary variation in graduate admissions criteria and practices. To better understand how disciplines shape admissions preferences and practices, which in turn may shape student access to graduate education, this article uncovers…

  12. 7 CFR 15a.22 - Preference in admission.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 1 2014-01-01 2014-01-01 false Preference in admission. 15a.22 Section 15a.22 Agriculture Office of the Secretary of Agriculture EDUCATION PROGRAMS OR ACTIVITIES RECEIVING OR BENEFITTING FROM FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and...

  13. 7 CFR 15a.22 - Preference in admission.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 1 2011-01-01 2011-01-01 false Preference in admission. 15a.22 Section 15a.22 Agriculture Office of the Secretary of Agriculture EDUCATION PROGRAMS OR ACTIVITIES RECEIVING OR BENEFITTING FROM FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Admission and...

  14. 28 CFR 541.47 - Admission to control unit.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Admission to control unit. 541.47 Section 541.47 Judicial Administration BUREAU OF PRISONS, DEPARTMENT OF JUSTICE INSTITUTIONAL MANAGEMENT INMATE DISCIPLINE AND SPECIAL HOUSING UNITS Control Unit Programs § 541.47 Admission to control...

  15. 42 CFR 93.519 - Admissibility of evidence.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... RESEARCH MISCONDUCT Opportunity To Contest ORI Findings of Research Misconduct and HHS Administrative Actions Hearing Process § 93.519 Admissibility of evidence. (a) The ALJ decides the admissibility of... of Witness). (i) Evidence about offers of compromise or settlement made in this action...

  16. 42 CFR 93.519 - Admissibility of evidence.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... RESEARCH MISCONDUCT Opportunity To Contest ORI Findings of Research Misconduct and HHS Administrative Actions Hearing Process § 93.519 Admissibility of evidence. (a) The ALJ decides the admissibility of... of Witness). (i) Evidence about offers of compromise or settlement made in this action...

  17. Assessing Academic Potential for University Admission: The Biographical Questionnaire

    ERIC Educational Resources Information Center

    Enslin, P. A.; Button, A.; Chakane, M.; de Groot, M.; Dison, L.

    2006-01-01

    A Biographical Questionnaire (BQ) has been used in the Faculty of Humanities at the University of the Witwatersrand since the mid-80s, to identify potential to succeed at university among applicants who have not met the requirements for automatic admission. As the key instrument in a special admissions process, the BQ's history and assumptions are…

  18. 20 CFR 410.696 - Evidence admissible on review.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Evidence admissible on review. 410.696 Section 410.696 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL COAL MINE HEALTH AND SAFETY ACT..., Administrative Review, Finality of Decisions, and Representation of Parties § 410.696 Evidence admissible...

  19. 42 CFR 418.25 - Admission to hospice care.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Admission to hospice care. 418.25 Section 418.25... (CONTINUED) MEDICARE PROGRAM HOSPICE CARE Eligibility, Election and Duration of Benefits § 418.25 Admission to hospice care. (a) The hospice admits a patient only on the recommendation of the medical...

  20. Virginia Western Community College's Health Technology Admissions Evaluation System.

    ERIC Educational Resources Information Center

    Houston, Charles A.; Sellers, Harry

    Due to factors such as high enrollment demands, limited institutional space, and high program costs, certain admissions requirements in the guidance/selection of students for health technology programs at Virginia Western Community College (VWCC) have become necessary. A Health Technology Admissions Evaluation System was created to develop and…