Science.gov

Sample records for adsorption isotherm study

  1. Adsorption isotherm special study. Final report

    SciTech Connect

    1993-05-01

    The study was designed to identify methods to determine adsorption applicable to Uranium Mill Tailings Remedial Action (UMTRA) Project sites, and to determine how changes in aquifer conditions affect metal adsorption, resulting retardation factors, and estimated contaminant migration rates. EPA and ASTM procedures were used to estimate sediment sorption of U, As, and Mo under varying groundwater geochemical conditions. Aquifer matrix materials from three distinct locations at the DOE UMTRA Project site in Rifle, CO, were used as the adsorbents under different pH conditions; these conditions stimulated geochemical environments under the tailings, near the tailings, and downgradient from the tailings. Grain size, total surface area, bulk and clay mineralogy, and petrography of the sediments were characterized. U and Mo yielded linear isotherms, while As had nonlinear ones. U and Mo were adsorbed strongly on sediments acidified to levels similar to tailings leachate. Changes in pH had much less effect on As adsorption. Mo was adsorbed very little at pH 7-7.3, U was weakly sorbed, and As was moderately sorbed. Velocities were estimated for metal transport at different pHs. Results show that the aquifer materials must be characterized to estimate metal transport velocities in aquifers and to develop groundwater restoration strategies for the UMTRA project.

  2. Adsorption Isotherm studies of Methyl Bromide adsorbed on Magnesium Oxide

    NASA Astrophysics Data System (ADS)

    Burns, Teresa; Sprung, Michael

    2005-03-01

    Understanding the interaction of polar molecules with ionic surfaces is technologically very important. Using high precision, volumetric adsorption isotherms the layering properties of methyl bromide on the MgO(100) surface were examined between 164 K and 179 K. Methyl bromide (Triple point = 179.49K) is found to exhibit two layering transitions within this temperature interval. Thermodynamic quantities derived from this study including the layering transition temperatures, the 2D compressibility, layer enthalpy and entropy of adsorption, and the isosteric enthalpy of adsorption will be presented. Comparisons with the adsorption properties of methyl chloride and methyl iodide will also be included.

  3. Isotherm study of reactive Blue 19 adsorption by an alum sludge

    NASA Astrophysics Data System (ADS)

    Khim, Ong Keat; Nor, Mohd Asri Md; Mohamad, Syuriya; Nasaruddin, Nas Aulia Ahmad; Jamari, Nor Laili-Azua; Yunus, Wan Md Zin Wan

    2015-05-01

    This study investigates the adsorption of Reactive Blue 19 using dewatered alum sludge. The dewatered alum sludge was a sludge produced from drinking water treatment plant. Batch adsorption experiments were performed to investigate the mechanism of the dye adsorption. The adsorption was rapid at its initial stage but the rate decreased as it approached equilibrium. The adsorption data were evaluated by Langmuir and Freundlich isotherm models but was best described by the Langmuir isotherm model as it gave the highest correlation.

  4. Enhanced fluoride adsorption by nano crystalline γ-alumina: adsorption kinetics, isotherm modeling and thermodynamic studies

    NASA Astrophysics Data System (ADS)

    Chinnakoti, Prathibha; Chunduri, Avinash L. A.; Vankayala, Ranganayakulu K.; Patnaik, Sandeep; Kamisetti, Venkataramaniah

    2016-06-01

    Nano materials in particular nano oxides with enhanced surface area and an excellent catalytic surface serve as potential adsorbents for defluoridation of water. In the present study nano γ-alumina was synthesized through a simple and low cost, surfactant assisted solution combustion method. As synthesized material was characterized by XRD and FESEM for its phase, size and morphological characteristics. Surface properties have been investigated by BET method. Nano γ-alumina was further used for a detailed adsorption study to remove fluoride from water. Batches of experiments were performed at various experimental conditions such as solution pH, adsorbent dose, initial fluoride concentration and contact time to test the defluoridation ability of γ-alumina. Fluoride Adsorption by nano sized γ-alumina was rapid and reached equilibrium within two hours. The adsorption worked well at pH 4.0, where ˜96 % of fluoride was found to be adsorbed on adsorbent. It was possible to reduce fluoride levels to as low as 0.3 mg/L (within the safe limit of WHO: ≤1.5 mg/L) from an initial fluoride levels of 10 mg/L. This could be achieved using a very small quantity, 1 g/L of γ-alumina at pH 4 within 1 h of contact time. Defluoridation capacity of nano γ-alumina was further investigated by fitting the equilibrium data to various isotherm as well as kinetic models. The present study revealed that γ-alumina could be an efficient adsorbent for treating fluoride contaminated water.

  5. Eriobotrya japonica seed biocomposite efficiency for copper adsorption: Isotherms, kinetics, thermodynamic and desorption studies.

    PubMed

    Mushtaq, Mehwish; Bhatti, Haq Nawaz; Iqbal, Munawar; Noreen, Saima

    2016-07-01

    Adsorption techniques are widely used to remove pollutants from wastewater; however, composites are gaining more importance due to their excellent adsorption properties. Bentonite composite with Eriobotrya japonica seed was prepared and used for the adsorption of copper (Cu) metal from aqueous media. The process variables such as pH, Cu(II) ions initial concentration, adsorbent dose, contact time and temperature were optimized for maximum Cu(II) adsorption. At pH 5, adsorbent dose 0.1 g, contact time 45 min, Cu(II) ions initial concentration 75 mg/L and temperature 45 °C, maximum Cu(II) adsorption was achieved. Desorption studies revealed that biocomposite is recyclable. Langmuir, Freundlich and Harkins-Jura isotherms as well as pseudo-first and pseudo-second-order kinetics models were applied to understand the adsorption mechanism. Thermodynamic parameters (ΔG(0), ΔH(0) and ΔS(0)) suggest that the adsorption process was spontaneous and endothermic in nature. The pseudo-second-order kinetic model and Langmuir isotherm fitted well to the adsorption data. Results showed that biocomposite was more efficient for Cu(II) adsorption in comparison to individuals native Eriobotrya japonica seed biomass and Na-bentonite.

  6. Eriobotrya japonica seed biocomposite efficiency for copper adsorption: Isotherms, kinetics, thermodynamic and desorption studies.

    PubMed

    Mushtaq, Mehwish; Bhatti, Haq Nawaz; Iqbal, Munawar; Noreen, Saima

    2016-07-01

    Adsorption techniques are widely used to remove pollutants from wastewater; however, composites are gaining more importance due to their excellent adsorption properties. Bentonite composite with Eriobotrya japonica seed was prepared and used for the adsorption of copper (Cu) metal from aqueous media. The process variables such as pH, Cu(II) ions initial concentration, adsorbent dose, contact time and temperature were optimized for maximum Cu(II) adsorption. At pH 5, adsorbent dose 0.1 g, contact time 45 min, Cu(II) ions initial concentration 75 mg/L and temperature 45 °C, maximum Cu(II) adsorption was achieved. Desorption studies revealed that biocomposite is recyclable. Langmuir, Freundlich and Harkins-Jura isotherms as well as pseudo-first and pseudo-second-order kinetics models were applied to understand the adsorption mechanism. Thermodynamic parameters (ΔG(0), ΔH(0) and ΔS(0)) suggest that the adsorption process was spontaneous and endothermic in nature. The pseudo-second-order kinetic model and Langmuir isotherm fitted well to the adsorption data. Results showed that biocomposite was more efficient for Cu(II) adsorption in comparison to individuals native Eriobotrya japonica seed biomass and Na-bentonite. PMID:27039361

  7. Electrochemically enhanced adsorption of nonylphenol on carbon nanotubes: Kinetics and isotherms study.

    PubMed

    Li, Xiaona; Chen, Shuo; Li, Liying; Quan, Xie; Zhao, Huimin

    2014-02-01

    Removal of nonylphenol (NP) from aqueous solution has attracted widely attention due to its aquatic toxicity and potential to disrupt the endocrine system. In an effort to develop the effective and environment-friendly treatment method for NP, adsorption of 4-n-nonylphenol (4-NP) on multi-walled carbon nanotubes (MWCNTs) under electrochemical assistance was studied. The adsorption kinetics and isotherms were investigated at different polarization potentials and compared with those of open circuit (OC) and powder MWCNTs adsorption. The adsorption kinetics was simulated by the model including pseudo-first-order model, pseudo-second-order model and intraparticle diffusion model. The isotherm was simulated with Langmuir model and Freudlich model, respectively. Experimental results indicated that 4-NP is able to be efficiently removed at a potential of -0.6V. Comparing with that of powder MWCNTs adsorption, the initial adsorption rate υ0 at -0.6V increased 7.9-fold according to pseudo-second-order model and the maximum adsorption capacity qm improved 1.7-fold according to Langmuir model. The improved adsorption effect at negative potential was ascribed to enhanced π-π electron-donor-acceptor (EDA) interaction between 4-NP and MWCNTs under electrochemical assistance.

  8. Removal Rate of Organic Matter Using Natural Cellulose via Adsorption Isotherm and Kinetic Studies.

    PubMed

    Din, Mohd Fadhil Md; Ponraj, Mohanadoss; Low, Wen-Pei; Fulazzaky, Mohamad Ali; Iwao, Kenzo; Songip, Ahmad Rahman; Chelliapan, Shreeshivadasan; Ismail, Zulhilmi; Jamal, Mohamad Hidayat

    2016-02-01

    In this study, the removal of natural organic matter (NOM) using coconut fiber (CF) and palm oil fiber (POF) was investigated. Preliminary analysis was performed using a jar test for the selection of optimal medium before the fabricated column model experiment. The equilibrium studies on isotherms and kinetic models for NOM adsorption were analyzed using linearized correlation coefficient. Results showed that the equilibrium data were fitted to Langmuir isotherm model for both CF and POF. The most suitable adsorption model was the pseudo-first-order kinetic model for POF and pseudo-second-order kinetic model for CF. The adsorption capacities achieved by the CF and POF were 15.67 and 30.8 mg/g respectively. Based on this investigation, it can be concluded that the POF is the most suitable material for the removal of NOM in semi polluted river water.

  9. Removal Rate of Organic Matter Using Natural Cellulose via Adsorption Isotherm and Kinetic Studies.

    PubMed

    Din, Mohd Fadhil Md; Ponraj, Mohanadoss; Low, Wen-Pei; Fulazzaky, Mohamad Ali; Iwao, Kenzo; Songip, Ahmad Rahman; Chelliapan, Shreeshivadasan; Ismail, Zulhilmi; Jamal, Mohamad Hidayat

    2016-02-01

    In this study, the removal of natural organic matter (NOM) using coconut fiber (CF) and palm oil fiber (POF) was investigated. Preliminary analysis was performed using a jar test for the selection of optimal medium before the fabricated column model experiment. The equilibrium studies on isotherms and kinetic models for NOM adsorption were analyzed using linearized correlation coefficient. Results showed that the equilibrium data were fitted to Langmuir isotherm model for both CF and POF. The most suitable adsorption model was the pseudo-first-order kinetic model for POF and pseudo-second-order kinetic model for CF. The adsorption capacities achieved by the CF and POF were 15.67 and 30.8 mg/g respectively. Based on this investigation, it can be concluded that the POF is the most suitable material for the removal of NOM in semi polluted river water. PMID:26803100

  10. Adsorption of surfactants on sand surface in enhanced oil recovery: Isotherms, kinetics and thermodynamic studies

    NASA Astrophysics Data System (ADS)

    Bera, Achinta; Kumar, T.; Ojha, Keka; Mandal, Ajay

    2013-11-01

    Adsorption of surfactants onto reservoir rock surface may result in the loss and reduction of their concentrations in surfactant flooding, which may render them less efficient or ineffective in practical applications of enhanced oil recovery (EOR) techniques. Surfactant flooding for EOR received attraction due to its ability to increase the displacement efficiency by lowering the interfacial tension between oil and water and mobilizing the residual oil. This article highlights the adsorption of surfactants onto sand surface with variation of different influencing factors. It has been experimentally found that adsorption of cationic surfactant on sand surface is more and less for anionic surfactant, while non-ionic surfactant shows intermediate behaviour. X-ray diffraction (XRD) study of clean sand particles has been made to determine the main component present in the sand particles. The interaction between sand particles and surfactant has been studied by Fourier Transform Infrared (FTIR) Spectroscopy of the sand particles before and after aging with surfactant. Salinity plays an important role in adsorption of anionic surfactant. Batch experiments were also performed to understand the effects of pH and adsorbent dose on the sorption efficiency. The sand particles exhibited high adsorption efficiency at low pH for anionic and nonionic surfactants. But opposite trend was found for cationic surfactant. Adsorption data were analyzed by fitting with Langmuir, Freundlich, Redlich-Peterson, and Sips isotherm models. Results show that the Langmuir isotherm and pseudo-second order kinetics models suit the equilibrium and kinetics of adsorption on sand surface. Thermodynamics feasibility of the adsorption process was also studied to verify the spontaneity of the process.

  11. Magnetic vinylphenyl boronic acid microparticles for Cr(VI) adsorption: kinetic, isotherm and thermodynamic studies.

    PubMed

    Kara, Ali; Demirbel, Emel; Tekin, Nalan; Osman, Bilgen; Beşirli, Necati

    2015-04-01

    Magnetic vinylphenyl boronic acid microparticles, poly(ethylene glycol dimethacrylate(EG)-vinylphenyl boronic acid(VPBA)) [m-poly(EG-VPBA)], produced by suspension polymerization and characterized, was found to be an efficient solid polymer for Cr(VI) adsorption. The m-poly(EG-VPBA) microparticles were prepared by copolymerizing of ethylene glycol dimethylacrylate (EG) with 4-vinyl phenyl boronic acid (VPBA). The m-poly(EG-VPBA) microparticles were characterized by N2 adsorption/desorption isotherms, electron spin resonance (ESR), X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), elemental analysis, scanning electron microscope (SEM) and swelling studies. The m-poly(EG-VPBA) microparticles were used at adsorbent/Cr(VI) ion ratios. The influence of pH, Cr(VI) initial concentration, temperature of the removal process was investigated. The maximum removal of Cr(VI) was observed at pH 2. Langmuir isotherm and Dubinin-Radushkvich isotherm were found to better fit the experiment data rather than Fruendlich isotherm. The kinetics of the adsorption process of Cr(VI) on the m-poly(EG-VPBA) microparticles were investigated using the pseudo first-order, pseudo-second-order, Ritch-second-order and intraparticle diffusion models, results showed that the pseudo-second order equation model provided the best correlation with the experimental results. The thermodynamic parameters (free energy change, ΔG(0) enthalpy change, ΔH(0); and entropy change, ΔS(0)) for the adsorption have been evaluated. PMID:25666882

  12. Adsorption isotherm of non-azeotropic solution onto porous adsorbents

    NASA Astrophysics Data System (ADS)

    Bono, A.; Ramlan, N. A.; Anisuzzaman, S. M.; Chu, C. M.; Farm, Y. Y.

    2016-06-01

    Adsorption isotherm is essential component in the understanding of the adsorption process. Several methods of the measurements, analysis and interpretation of adsorption from solution have been reported in the literature. Most of the measurements of adsorption isotherm from solution were involved the measurement of excess isotherm conducted at low region of sorbates concentration. Direct interpretation of excess adsorption isotherm as adsorption isotherm is always been practice. Therefore, in this work a study on the measurement of the adsorption isotherm from solution of non-azeotropic organic solvent mixture onto porous adsorbents for whole range of liquid concentration was conducted. The study included the measurement of excess adsorption isotherm using conventional technique. Theoretical analysis and interpretation of adsorption isotherm from the excess isotherm were conducted using Pseudo Ideal Adsorption, Gibbs Dividing Plane Model and Langmuir-Fruendlich binary isotherm model. For organic solvents, acetone and propanol were chosen as the adsorbates due to the non-azeotropic properties in the mixture. Activated carbon and silicalite were chosen as adsorbents due to the different in their porosity such as macro porous and micro porous structure. The result of the study has revealed that the adsorption isotherm of non-azeotropic mixture onto activated carbon and silicalite can be interpreted as monolayer type of adsorption.

  13. Adsorption of Phenol from Aqueous Solution Using Lantana camara, Forest Waste: Kinetics, Isotherm, and Thermodynamic Studies

    PubMed Central

    Girish, C. R.; Ramachandra Murty, V.

    2014-01-01

    The present work investigates the potential of Lantana camara, a forest waste, as an adsorbent for the phenol reduction in wastewater. Batch studies were conducted with adsorbent treated with HCl and KOH to determine the influence of various experimental parameters such as pH, contact time, adsorbent dosage, and phenol concentration. The experimental conditions were optimized for the removal of phenol from wastewater. Equilibrium isotherms for the adsorption of phenol were analyzed by Freundlich, Langmuir, Temkin, and Dubinin-Radushkevich isotherm models. Thermodynamic parameters like the Gibbs free energy (ΔG°), enthalpy (ΔH°), and entropy (ΔS°) were also determined and they showed that the adsorption process was feasible, spontaneous, and exothermic in the temperature range of 298–328 K. The kinetic data were fitted with pseudo-second-order model. The equilibrium data that followed Langmuir model with the monolayer adsorption capacity was found to be 112.5 mg/g and 91.07 mg/g for adsorbent treated with HCl and KOH, respectively, for the concentration of phenol ranging from 25 to 250 mg/L. This indicates that the Lantana camara was a promising adsorbent for the removal of phenol from aqueous solutions. PMID:27350997

  14. Study and numerical solution of a generalized mathematical model of isothermal adsorption

    SciTech Connect

    Komissarov, Yu.A.; Vetokhin, V.N.; Tsenev, V.A.; Gordeeva, E.L.

    1995-06-01

    A generalized mathematical model of isothermal adsorption that takes into account mass transfer on the surface of a particle, diffusion in micro- and macropores, and dispersion along the length of the apparatus is considered The parameters {lambda} and {var_phi}{sup 2} determine the dominating effect of any of the mass transfer mechanisms of the adsorption process. A numerical algorithm for solving the generalized adsorption model is suggested.

  15. Adsorption of malachite green by polyaniline-nickel ferrite magnetic nanocomposite: an isotherm and kinetic study

    NASA Astrophysics Data System (ADS)

    Patil, Manohar R.; Shrivastava, V. S.

    2014-11-01

    This work deals with the development of an efficient method for the removal of a MG (malachite green) dye from aqueous solution using polyaniline (PANI)-Nickel ferrite (NiFe2O4) magnetic nanocomposite. It is successfully synthesised in situ through self polymerisation of monomer aniline. Adsorptive removal studies are carried out for water soluble MG dye using PANI-Nickel ferrite magnetic nanocomposite in aqueous solution. Different parameters like dose of adsorbent, contact time, different initial conc., and pH have been studied to optimise reaction condition. It is concluded that adsorptive removal by PANI-Nickel ferrite magnetic nanocomposite is an efficient method for removing a MG dye from aqueous solution than work done before. The optimum conditions for the removal of the dye are initial concentration 30 mg l-1, adsorbent dose 5gm l-1 and pH 7. The adsorption capacity is found 4.09 mg g-1 at optimum condition 30 mg l-1. The adsorption followed pseudo-second-order kinetics. The experimental isotherm is found to fit with Langmuir equation. The prepared adsorbent is characterised by techniques SEM, EDS, XRD and VSM.

  16. Statistical physics studies of multilayer adsorption isotherm in food materials and pore size distribution

    NASA Astrophysics Data System (ADS)

    Aouaini, F.; Knani, S.; Ben Yahia, M.; Ben Lamine, A.

    2015-08-01

    Water sorption isotherms of foodstuffs are very important in different areas of food science engineering such as for design, modeling and optimization of many processes. The equilibrium moisture content is an important parameter in models used to predict changes in the moisture content of a product during storage. A formulation of multilayer model with two energy levels was based on statistical physics and theoretical considerations. Thanks to the grand canonical ensemble in statistical physics. Some physicochemical parameters related to the adsorption process were introduced in the analytical model expression. The data tabulated in literature of water adsorption at different temperatures on: chickpea seeds, lentil seeds, potato and on green peppers were described applying the most popular models applied in food science. We also extend the study to the newest proposed model. It is concluded that among studied models the proposed model seems to be the best for description of data in the whole range of relative humidity. By using our model, we were able to determine the thermodynamic functions. The measurement of desorption isotherms, in particular a gas over a solid porous, allows access to the distribution of pore size PSD.

  17. Batch removal of malachite green from aqueous solutions by adsorption on oil palm trunk fibre: equilibrium isotherms and kinetic studies.

    PubMed

    Hameed, B H; El-Khaiary, M I

    2008-06-15

    Oil palm trunk fibre (OPTF)--an agricultural solid waste--was used as low-cost adsorbent to remove malachite green (MG) from aqueous solutions. The operating variables studied were contact time, initial dye concentration, and solution pH. Equilibrium adsorption data were analyzed by three isotherms, namely the Freundlich isotherm, the Langmuir isotherm, and the multilayer adsorption isotherm. The best fit to the data was obtained with the multilayer adsorption. The monolayer adsorption capacity of OPTF was found to be 149.35 mg/g at 30 degrees C. Adsorption kinetic data were modeled using the Lagergren pseudo-first-order, Ho's pseudo-second-order and Elovich models. It was found that the Lagergren's model could be used for the prediction of the system's kinetics. The overall rate of dye uptake was found to be controlled by external mass transfer at the beginning of adsorption, then for initial MG concentrations of 25, 50, 100, 150, and 300 mg/L the rate-control changed to intraparticle diffusion at a later stage, but for initial MG concentrations 200 and 250 mg/L no evidence was found of intraparticle diffusion at any period of adsorption. It was found that with increasing the initial concentration of MG, the pore-diffusion coefficient increased while the film-diffusion coefficient decreased. PMID:18022316

  18. Experimental studies of hydrogen on boron nitride: I. Adsorption isotherms of HD

    SciTech Connect

    Evans, M.D.; Sullivan, N.S.

    1995-09-01

    The authors report the results of measurements of adsorption isotherms of deuterium hydride (HD) adsorbed onto boron nitride. From this data they derive both the two-dimensional critical point temperatures (using Larher`s method) and the heat of adsorption for the first few layers of this system. These results are compared with similar measurements of HD adsorbed onto graphite and MgO. While substantial substeps within some adlayer steps are evident in the adsorption isotherms of HD on graphite and MgO and have been shown to indicate a two-dimensional liquid-solid transition within the layer, no substep is evident at the level of one percent of a step level for HD adsorbed onto BN.

  19. Adsorption of fluoride to UiO-66-NH2 in water: Stability, kinetic, isotherm and thermodynamic studies.

    PubMed

    Lin, Kun-Yi Andrew; Liu, Yu-Ting; Chen, Shen-Yi

    2016-01-01

    To provide safe drinking water, fluoride in water must be removed and adsorption processes appear to be the most widely used method. Metal organic frameworks (MOFs) represent a new class of adsorbents that have been used in various adsorption applications. To study the adsorption mechanism of fluoride to MOFs in water and obtain related adsorption parameters, we synthesized a zirconium-based MOF with a primary amine group on its ligand, named UiO-66-NH2. The kinetics, adsorption isotherm and thermodynamics of fluoride adsorption to UiO-66-NH2 were investigated. The crystalline structure of UiO-66-NH2 remained intact and the local structure of zirconium in UiO-66-NH2 did not change significantly after being exposed to fluoride. The kinetics of the fluoride adsorption in UiO-66-NH2 could be well represented by the pseudo second order rate law. The enthalpy of the adsorption indicates that the F(-) adsorption to UiO-66-NH2 was classified as a physical adsorption. However, the comparison between the adsorption capacities of UiO-66-NH2 and UiO-66 suggests that the fluoride adsorption to UiO-66-NH2 might primarily involve a strong interaction between F(-) and the metal site. The fluoride adsorption capacity of UiO-66-NH2 was found to decrease when pH>7. While the presence of chloride/bromide ions did not noticeably change the adsorption capacity of UiO-66-NH2, the ionic surfactants slightly affected the adsorption capacity of UiO-66-NH2. These findings provide insights to further optimize the adsorption process for removal of fluoride using zirconium-based MOFs. PMID:26397913

  20. Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds.

    PubMed

    Ramos-Ramírez, Esthela; Ortega, Norma L Gutiérrez; Soto, Cesar A Contreras; Gutiérrez, Maria T Olguín

    2009-12-30

    In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio=2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N(2) adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

  1. The special features of protein adsorption isotherms on silica adsorbents

    NASA Astrophysics Data System (ADS)

    Chukhrai, E. S.; Atyaksheva, L. F.; Pilipenko, O. S.

    2011-05-01

    The adsorption isotherms of hemoglobin, peroxidase, and β-galactosidase on silochrome and mesoporous and biporous silicas were comparatively studied. Adsorption developed in two stages, including fast "reversible" protein adsorption (equilibrium was reached in t ≤ 1-2 h) and a "slow stage" of irreversible binding in t ≫ 24 h (multipoint adsorption). The corresponding equilibrium constants were determined. The mechanism of unlimited linear association of peroxidase in the adsorption layer on the surface of silochrome was established.

  2. Adsorption Isotherms and Surface Reaction Kinetics

    ERIC Educational Resources Information Center

    Lobo, L. S.; Bernardo, C. A.

    1974-01-01

    Explains an error that occurs in calculating the conditions for a maximum value of a rate expression for a bimolecular reaction. The rate expression is derived using the Langmuir adsorption isotherm to relate gas pressures and corresponding surface coverages. (GS)

  3. Kinetic and isotherm error optimization studies for adsorption of atrazine and imidacloprid on bark of Eucalyptus tereticornis L.

    PubMed

    Mandal, Abhishek; Singh, Neera

    2016-01-01

    The aim of this study was to establish the bark of Eucalyptus tereticornis L. (EB) as a low cost bio-adsorbent for the removal of imidacloprid and atrazine from aqueous medium. The pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich and intra-particle diffusion (IPD) models were used to describe the kinetic data and rate constants were evaluated. Adsorption data was analysed using ten 2-, 3- and 4-parameter models viz. Freundlich, Jovanovic, Langmuir, Temkin, Koble-Corrigan, Redlich-Peterson, Sips, Toth, Radke-Prausnitz, and Fritz-Schluender isotherms. Six error functions were used to compute the best fit single component isotherm parameters by nonlinear regression analysis. The results showed that the sorption of atrazine was better explained by PSO model, whereas the sorption of imidacloprid followed the PFO kinetic model. Isotherm model optimization analysis suggested that the Freundlich along with Koble-Corrigan, Toth and Fritz-Schluender were the best models to predict atrazine and imidacloprid adsorption onto EB. Error analysis suggested that minimization of chi-square (χ(2)) error function provided the best determination of optimum parameter sets for all the isotherms.

  4. Rapid Adsorption of Copper(II) and Lead(II) by Rice Straw/Fe3O4 Nanocomposite: Optimization, Equilibrium Isotherms, and Adsorption Kinetics Study

    PubMed Central

    Khandanlou, Roshanak; Ahmad, Mansor B.; Fard Masoumi, Hamid Reza; Shameli, Kamyar; Basri, Mahiran; Kalantari, Katayoon

    2015-01-01

    Rice straw/magnetic nanocomposites (RS/Fe3O4-NCs) were prepared via co-precipitation method for removal of Pb(II) and Cu(II) from aqueous solutions. Response surface methodology (RSM) was utilized to find the optimum conditions for removal of ions. The effects of three independent variables including initial ion concentration, removal time, and adsorbent dosage were investigated on the maximum adsorption of Pb (II) and Cu (II). The optimum conditions for the adsorption of Pb(II) and Cu(II) were obtained (100 and 60 mg/L) of initial ion concentration, (41.96 and 59.35 s) of removal time and 0.13 g of adsorbent for both ions, respectively. The maximum removal efficiencies of Pb(II) and Cu(II) were obtained 96.25% and 75.54%, respectively. In the equilibrium isotherm study, the adsorption data fitted well with the Langmuir isotherm model. The adsorption kinetics was best depicted by the pseudo-second order model. Desorption experiments showed adsorbent can be reused successfully for three adsorption-desorption cycles. PMID:25815470

  5. Rapid adsorption of copper(II) and lead(II) by rice straw/Fe₃O₄ nanocomposite: optimization, equilibrium isotherms, and adsorption kinetics study.

    PubMed

    Khandanlou, Roshanak; Ahmad, Mansor B; Fard Masoumi, Hamid Reza; Shameli, Kamyar; Basri, Mahiran; Kalantari, Katayoon

    2015-01-01

    Rice straw/magnetic nanocomposites (RS/Fe3O4-NCs) were prepared via co-precipitation method for removal of Pb(II) and Cu(II) from aqueous solutions. Response surface methodology (RSM) was utilized to find the optimum conditions for removal of ions. The effects of three independent variables including initial ion concentration, removal time, and adsorbent dosage were investigated on the maximum adsorption of Pb (II) and Cu (II). The optimum conditions for the adsorption of Pb(II) and Cu(II) were obtained (100 and 60 mg/L) of initial ion concentration, (41.96 and 59.35 s) of removal time and 0.13 g of adsorbent for both ions, respectively. The maximum removal efficiencies of Pb(II) and Cu(II) were obtained 96.25% and 75.54%, respectively. In the equilibrium isotherm study, the adsorption data fitted well with the Langmuir isotherm model. The adsorption kinetics was best depicted by the pseudo-second order model. Desorption experiments showed adsorbent can be reused successfully for three adsorption-desorption cycles.

  6. Dye adsorption of cotton fabric grafted with PPI dendrimers: Isotherm and kinetic studies.

    PubMed

    Salimpour Abkenar, Samera; Malek, Reza Mohammad Ali; Mazaheri, Firouzmehr

    2015-11-01

    In this research, the cotton fabrics grafted with two generations of the poly(propylene imine) dendrimers were applied to adsorb textile dyes from aqueous solutions. Direct Red 80 (anionic dye), Disperse Yellow 42 (nonionic dye) and Basic Blue 9 (cationic dye) were selected as model dyes. The effect of various experimental parameters such as initial concentration of dyes, charge of dyes molecule, salt and pH was investigated on the adsorption process. Furthermore, kinetics and equilibrium of the adsorption process on the grafted samples were studied. It was found that maximum adsorption of anionic and disperse dyes took place at around pH 3, while cationic dye could be adsorbed at around pH 11. The Langmuir equation was able to describe the mechanism of dyes adsorption. In addition, the second-order equation was found to be fit with the kinetics data. Interestingly, it seems that the dye adsorption of the grafted fabrics is strongly pH dependent. PMID:26292774

  7. Dye adsorption of cotton fabric grafted with PPI dendrimers: Isotherm and kinetic studies.

    PubMed

    Salimpour Abkenar, Samera; Malek, Reza Mohammad Ali; Mazaheri, Firouzmehr

    2015-11-01

    In this research, the cotton fabrics grafted with two generations of the poly(propylene imine) dendrimers were applied to adsorb textile dyes from aqueous solutions. Direct Red 80 (anionic dye), Disperse Yellow 42 (nonionic dye) and Basic Blue 9 (cationic dye) were selected as model dyes. The effect of various experimental parameters such as initial concentration of dyes, charge of dyes molecule, salt and pH was investigated on the adsorption process. Furthermore, kinetics and equilibrium of the adsorption process on the grafted samples were studied. It was found that maximum adsorption of anionic and disperse dyes took place at around pH 3, while cationic dye could be adsorbed at around pH 11. The Langmuir equation was able to describe the mechanism of dyes adsorption. In addition, the second-order equation was found to be fit with the kinetics data. Interestingly, it seems that the dye adsorption of the grafted fabrics is strongly pH dependent.

  8. Kinetic and isotherm studies of adsorption and biosorption processes in the removal of phenolic compounds from aqueous solutions: comparative study

    PubMed Central

    2013-01-01

    The phenolic compounds are known by their carcinogenicity and high toxicity as well as creating unpleasant taste and odor in water resources. The present study develops a cost-effective technology for the treatment of water contaminated with phenolic compounds, including Phenol (Ph), 2-chlorophenol (2-CP), and 4-chlorophenol (4-CP). So, two sorbents, rice bran ash (RBA) and biomass of brown algae, Cystoseiraindica, were used and results were compared with the commercially granular activated carbon (GAC). The phenolic compounds were determined using a high performance liquid chromatography (HPLC) under batch equilibrium conditions. The effects of contact time, pH, initial adsorbate concentration, and adsorbent dosages on the removal efficiency were studied. The adsorption data were simulated by isotherm and kinetic models. Results indicated that RBA and GAC had the lowest efficiency for the removal of 2-CP, while the order of removal efficiency for C. indica biomass was as follows: 2-CP > 4-CP > phenol. The efficiency of GAC was higher than those of other adsorbents for all of the phenolic compounds. Furthermore, the adsorption capacity of RBA was found to be higher than that of C. indica biomass. The optimal initial pH for the removal of phenol, 2-CP and 4-CP was determined to be 5, 7, and 7 for RBA, GAC, and algal biomass, respectively. Kinetic studies suggested that the pseudo-second order best fitted the kinetic data. PMID:24355013

  9. Adsorption of methyl orange from aqueous solution by aminated pumpkin seed powder: Kinetics, isotherms, and thermodynamic studies.

    PubMed

    Subbaiah, Munagapati Venkata; Kim, Dong-Su

    2016-06-01

    Present research discussed the utilization of aminated pumpkin seed powder (APSP) as an adsorbent for methyl orange (MO) removal from aqueous solution. Batch sorption experiments were carried to evaluate the influence of pH, initial dye concentration, contact time, and temperature. The APSP was characterized by using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The experimental equilibrium adsorption data were fitted using two two-parameter models (Langmuir and Freundlich) and two three-parameter models (Sips and Toth). Langmuir and Sips isotherms provided the best model for MO adsorption data. The maximum monolayer sorption capacity was found to be 200.3mg/g based on the Langmuir isotherm model. The pseudo-first-order and pseudo-second-order model equations were used to analyze the kinetic data of the adsorption process and the data was fitted well with the pseudo-second-order kinetic model (R(2)>0.97). The calculated thermodynamic parameters such as ΔG(0), ΔH(0) and ΔS(0) from experimental data showed that the sorption of MO onto APSP was feasible, spontaneous and endothermic in the temperature range 298-318 K. The FTIR results revealed that amine and carboxyl functional groups present on the surface of APSP. The SEM results show that APSP has an irregular and porous surface which is adequate morphology for dye adsorption. Desorption experiments were carried to explore the feasibility of adsorbent regeneration and the adsorbed MO from APSP was desorbed using 0.1M NaOH with an efficiency of 93.5%. Findings of the present study indicated that APSP can be successfully used for removal of MO from aqueous solution. PMID:26921544

  10. Experimental adsorption isotherms based on inverse gas chromatography.

    PubMed

    Kalogirou, E; Bassiotis, I; Artemiadi, Th; Margariti, S; Siokos, V; Roubani-Kalantzopoulou, F

    2002-09-01

    A new chromatographic perturbation method is used for studying the adsorption-desorption equilibrium in various gas-solid heterogeneous systems. It is the reversed-flow method giving accurate and precise values of many physicochemical constants including the basic and necessary adsorption isotherm values. For four inorganic oxides, namely, Cr2O3, Fe2O3, TiO2 and PbO, and two aromatic hydrocarbons (benzene, toluene) these adsorption isotherms have been determined through a non-linear model. PMID:12385379

  11. Simulated Water Adsorption Isotherms in Hydrophilic and Hydrophobic Cylinderical Nanopores

    SciTech Connect

    StrioloDr., A; Naicker, P. K.; Chialvo, Ariel A; Cummings, Peter T; Gubbins, Dr. K. E.

    2005-01-01

    Grand canonical Monte Carlo simulations are performed to study the adsorption of water in single-walled carbon nanotubes (SWCNs). At room temperature the resulting adsorption isotherms in (10:10) and wider SWCNs are characterized by negligible amount of water uptake at low pressures, sudden and complete pore filling once a threshold pressure is reached, and wide adsorption/desorption hysteresis loops. The width of these loops decreases as pore diameter narrows. Adsorption/desorption hysteresis loops are not observed for water adsorption in (6:6) SWCNs. When the nanotubes are doped with small amounts of oxygenated sites it is possible to obtain adsorption isotherms in which the water uptake increases gradually as the pressure increases. Simulated X-ray diffraction patterns for confined water are also reported.

  12. The Langmuir isotherm: a commonly applied but misleading approach for the analysis of protein adsorption behavior.

    PubMed

    Latour, Robert A

    2015-03-01

    The Langmuir adsorption isotherm provides one of the simplest and most direct methods to quantify an adsorption process. Because isotherm data from protein adsorption studies often appear to be fit well by the Langmuir isotherm model, estimates of protein binding affinity have often been made from its use despite that fact that none of the conditions required for a Langmuir adsorption process may be satisfied for this type of application. The physical events that cause protein adsorption isotherms to often provide a Langmuir-shaped isotherm can be explained as being due to changes in adsorption-induced spreading, reorientation, clustering, and aggregation of the protein on a surface as a function of solution concentration in contrast to being due to a dynamic equilibrium adsorption process, which is required for Langmuir adsorption. Unless the requirements of the Langmuir adsorption process can be confirmed, fitting of the Langmuir model to protein adsorption isotherm data to obtain thermodynamic properties, such as the equilibrium constant for adsorption and adsorption free energy, may provide erroneous values that have little to do with the actual protein adsorption process, and should be avoided. In this article, a detailed analysis of the Langmuir isotherm model is presented along with a quantitative analysis of the level of error that can arise in derived parameters when the Langmuir isotherm is inappropriately applied to characterize a protein adsorption process.

  13. Adsorption of Pb(II) on mesoporous activated carbons fabricated from water hyacinth using H3PO4 activation: Adsorption capacity, kinetic and isotherm studies

    NASA Astrophysics Data System (ADS)

    Huang, Yang; Li, Shunxing; Chen, Jianhua; Zhang, Xueliang; Chen, Yiping

    2014-02-01

    Activated carbons with high mesoporosity and abundant oxygen-containing functional groups were prepared from water hyacinth using H3PO4 activation (WHAC) to eliminate Pb(II) in water. Characterizations of the WHAC were performed using Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The BET analysis showed that WHAC possesses a high mesoporosity (93.9%) with a BET surface area of 423.6 m2/g. The presence of oxygen-containing functional groups including hydroxyl, carbonyl, carboxyl and phosphate groups renders the WHAC a favorable adsorbent for Pb(II) with the maximum monolayer capacity (qm) 118.8 mg/g. The adsorption behavior follows pseudo-first order kinetic and Langmuir isotherm. The desorption study demonstrated that the WHAC could be readily regenerated using 0.1 M HCl (pH = 1.0). The desorbed WHAC could be reused at least six times without significant adsorption capacity reduction. The adsorption process was spontaneous and endothermic with ΔG (-0.27, -1.13, -3.02, -3.62, -5.54, and -9.31 kJ/mol) and ΔH (38.72 kJ/mol). Under the optimized conditions, a small amount of the adsorbent (1.0 g/L) could remove as much as 90.1% of Pb(II) (50 mg/L) in 20 min at pH 6.0 and temperature of 298 K. Therefore, the WHAC has a great potential to be an economical and efficient adsorbent in the treatment of lead-contaminated water.

  14. The study of non-linear kinetics and adsorption isotherm models for Acid Red 18 from aqueous solutions by magnetite nanoparticles and magnetite nanoparticles modified by sodium alginate.

    PubMed

    Berizi, Zohre; Hashemi, Seyed Yaser; Hadi, Mahdi; Azari, Ali; Mahvi, Amir Hosein

    2016-01-01

    Azo dyes are widely used in various industries. These substances produce toxic byproducts in aquatic environments in addition to their mutagenic and carcinogenic potential effects. In this study, the effect of magnetite nanoparticles and magnetite nanoparticles modified by sodium alginate in batch systems and nonlinear kinetic and adsorption isotherm models were investigated. Magnetite nanoparticles were synthesized by chemical co-precipitation method and then modified and used as adsorbent to adsorb Acid Red 18. After determining the optimum pH and adsorbent dose, non-equilibrium models for kinetic adsorption were tested with concentrations (25-100 mg/L) and at eight different periods of time (1-15 min) and the pseudo-first-order and pseudo-second-order non-linear models were used to describe the results. For adsorption isotherm, a contact time of 120 min was studied in different concentrations (25-100 mg/L) and the residual concentration of Acid Red 18 was obtained. The results are described by non-linear Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. The optimum amounts of pH for magnetite nanoparticles and for modified ones were 3 and 5, respectively, the efficiencies were 0.75 and 0.2 g/L, respectively. According to the results sodium alginate has a high performance in adsorption of Acid Red 18. Adjusted correlation coefficients and chi-square test showed that Freundlich isotherm and then Langmuir isotherm can well describe the experimental results. In Freundlich, the value of (Kf) was 3.231 (L/g) for magnetite nanoparticles and 21.615 (L/g) for modified adsorbent. In Langmuir, the value of (qm) was 16.259 (mg/g) for magnetite nanoparticles and 73.464 (mg/g) for modified adsorbent. Comparing the Langmuir maximum calculated adsorption capacity indicated that modified adsorbent can adsorb the pollutants 6.5 times more than the other one.

  15. The study of non-linear kinetics and adsorption isotherm models for Acid Red 18 from aqueous solutions by magnetite nanoparticles and magnetite nanoparticles modified by sodium alginate.

    PubMed

    Berizi, Zohre; Hashemi, Seyed Yaser; Hadi, Mahdi; Azari, Ali; Mahvi, Amir Hosein

    2016-01-01

    Azo dyes are widely used in various industries. These substances produce toxic byproducts in aquatic environments in addition to their mutagenic and carcinogenic potential effects. In this study, the effect of magnetite nanoparticles and magnetite nanoparticles modified by sodium alginate in batch systems and nonlinear kinetic and adsorption isotherm models were investigated. Magnetite nanoparticles were synthesized by chemical co-precipitation method and then modified and used as adsorbent to adsorb Acid Red 18. After determining the optimum pH and adsorbent dose, non-equilibrium models for kinetic adsorption were tested with concentrations (25-100 mg/L) and at eight different periods of time (1-15 min) and the pseudo-first-order and pseudo-second-order non-linear models were used to describe the results. For adsorption isotherm, a contact time of 120 min was studied in different concentrations (25-100 mg/L) and the residual concentration of Acid Red 18 was obtained. The results are described by non-linear Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. The optimum amounts of pH for magnetite nanoparticles and for modified ones were 3 and 5, respectively, the efficiencies were 0.75 and 0.2 g/L, respectively. According to the results sodium alginate has a high performance in adsorption of Acid Red 18. Adjusted correlation coefficients and chi-square test showed that Freundlich isotherm and then Langmuir isotherm can well describe the experimental results. In Freundlich, the value of (Kf) was 3.231 (L/g) for magnetite nanoparticles and 21.615 (L/g) for modified adsorbent. In Langmuir, the value of (qm) was 16.259 (mg/g) for magnetite nanoparticles and 73.464 (mg/g) for modified adsorbent. Comparing the Langmuir maximum calculated adsorption capacity indicated that modified adsorbent can adsorb the pollutants 6.5 times more than the other one. PMID:27642843

  16. Activated carbon derived from carbon residue from biomass gasification and its application for dye adsorption: Kinetics, isotherms and thermodynamic studies.

    PubMed

    Maneerung, Thawatchai; Liew, Johan; Dai, Yanjun; Kawi, Sibudjing; Chong, Clive; Wang, Chi-Hwa

    2016-01-01

    In this work, activated carbon (AC) as an effective and low-cost adsorbent was successfully prepared from carbon residue (or char, one of the by-products from woody biomass gasification) via physical activation. The surface area of char was significantly increased from 172.24 to 776.46m(2)/g after steam activation at 900°C. The obtained activated carbons were then employed for the adsorption of dye (Rhodamine B) and it was found that activated carbon obtained from steam activation exhibited the highest adsorption capability, which is mainly attributed to the higher surface area and the abundance of hydroxyl (-OH) and carboxyl (-COOH) groups on the activated carbon surface. Moreover, it was also found that the adsorption capability significantly increased under the basic condition, which can be attributed to the increased electrostatic interaction between the deprotonated (negatively charged) activated carbon and dye molecules. Furthermore, the equilibrium data were fitted into different adsorption isotherms and found to fit well with Langmuir model (indicating that dye molecules form monolayer coverage on activated carbon) with a maximum monolayer adsorption capability of 189.83mg/g, whereas the adsorption kinetics followed the pseudo-second-order kinetics.

  17. Activated carbon derived from carbon residue from biomass gasification and its application for dye adsorption: Kinetics, isotherms and thermodynamic studies.

    PubMed

    Maneerung, Thawatchai; Liew, Johan; Dai, Yanjun; Kawi, Sibudjing; Chong, Clive; Wang, Chi-Hwa

    2016-01-01

    In this work, activated carbon (AC) as an effective and low-cost adsorbent was successfully prepared from carbon residue (or char, one of the by-products from woody biomass gasification) via physical activation. The surface area of char was significantly increased from 172.24 to 776.46m(2)/g after steam activation at 900°C. The obtained activated carbons were then employed for the adsorption of dye (Rhodamine B) and it was found that activated carbon obtained from steam activation exhibited the highest adsorption capability, which is mainly attributed to the higher surface area and the abundance of hydroxyl (-OH) and carboxyl (-COOH) groups on the activated carbon surface. Moreover, it was also found that the adsorption capability significantly increased under the basic condition, which can be attributed to the increased electrostatic interaction between the deprotonated (negatively charged) activated carbon and dye molecules. Furthermore, the equilibrium data were fitted into different adsorption isotherms and found to fit well with Langmuir model (indicating that dye molecules form monolayer coverage on activated carbon) with a maximum monolayer adsorption capability of 189.83mg/g, whereas the adsorption kinetics followed the pseudo-second-order kinetics. PMID:26512858

  18. The Calculation of Adsorption Isotherms from Chromatographic Peak Shapes

    ERIC Educational Resources Information Center

    Neumann, M. G.

    1976-01-01

    Discusses the relationship between adsorption isotherms and elution peak shapes in gas chromatography, and describes a laboratory experiment which involves the adsorption of hexane, cyclohexane, and benzene on alumina at different temperatures. (MLH)

  19. Liquid phase adsorptions of Rhodamine B dye onto raw and chitosan supported mesoporous adsorbents: isotherms and kinetics studies

    NASA Astrophysics Data System (ADS)

    Inyinbor, A. A.; Adekola, F. A.; Olatunji, G. A.

    2016-04-01

    Irvingia gabonensis endocarp waste was charred (DNc) and subsequently coated with chitosan (CCDNc). Physicochemical characteristics of the two adsorbents were established, while Fourier transform infrared (FTIR), Scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) surface area methods were further employed for characterization. Efficiencies of the prepared adsorbents in the uptake of Rhodamine B (RhB) from aqueous effluent were investigated and adsorption data were tested using four isotherms and four kinetics models. The BET surface areas of the prepared adsorbent were 0.0092 and 4.99 m2/g for DNc and CCDNc, respectively, and maximum adsorption was recorded at pH between 3 and 4, respectively. While monolayer adsorption dominates the uptake of RhB onto DNc, uptake of RhB onto CCDNc was onto heterogeneous surface. The maximum monolayer adsorption capacities (q max) obtained from the Langmuir equation are 52.90 and 217.39 mg/g for DNc and CCDNc, respectively. Pseudo second order and Elovich kinetic models well described the kinetics of the two adsorption processes. The mean sorption energy (E) calculated from the D-R model and desorption efficiencies suggests that while the uptake of RhB onto DNc was physical in nature, for RhB-CCDNc system chemisorption dominates.

  20. Study of the kinetics and the adsorption isotherm of cadmium(II) from aqueous solution using green algae (Ulva lactuca) biomass.

    PubMed

    Asnaoui, H; Laaziri, A; Khalis, M

    2015-01-01

    Batch experiments were conducted to study the adsorption of hazardous cadmium onto low-cost algae biomass in aqueous solution with respect to concentration of adsorbate, adsorbent dosage, contact time, solution pH and temperature. Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The activation energy of adsorption was also evaluated for the adsorption of cadmium onto Ulva lactuca biomass. Experimental data were tested in terms of biosorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the biosorption processes of Cd(II) followed well pseudo-second-order kinetics. Langmuir and Freundlich models were applied to describe the biosorption isotherm of the metal ions by Ulva lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The biosorption capacity of Ulva lactuca biomass for cadmium was found to be 3.02 mg/g at pH 5.60 min equilibrium time and 20 °C. The mean free energy which was calculated was 6.24 kJ/mol for Cd(II) biosorption, which shows that the adsorption is physical. The calculated thermodynamic parameters (ΔG0, ΔH0 and ΔS0) showed that the biosorption of Cd(II) onto Ulva lactuca biomass was feasible, spontaneous and exothermic under examined conditions. The results indicate that algae Ulva lactuca could be employed as a low-cost material for the removal of metal ions from aqueous solution. PMID:26524441

  1. Multifractal characteristics of Nitrogen adsorption isotherms from tropical soils

    NASA Astrophysics Data System (ADS)

    Vidal Vázquez, Eva; Paz Ferreiro, Jorge

    2010-05-01

    One of the primary methods used to characterize a wide range of porous materials, including soils, are gas adsorption isotherms. An adsorption isotherm is a function relating the amount of adsorbed gas or vapour to the respective equilibrium pressure, during pressure increase at constant temperature. Adsorption data allow easily estimates of specific surface area and also can provide a characterization of pore surface heterogeneity. Most of the properties and the reactivity of soil colloids are influenced by their specific surface area and by parameters describing the surface heterogeneity. For a restricted scale range, linearity between applied pressure and volume of adsorbate holds, which is the basis for current estimations of specific surface area. However, adsorption isotherms contain also non-linear segments of pressure versus volume so that evidence of multifractal scale has been demonstrated. The aim of this study was to analyze the multifractal behaviour of nitrogen adsorption isotherms from a set of tropical soils. Samples were collected form 54 horizons belonging to 19 soil profiles in the state of Minas Gerais, Brazil. The most frequent soil type was Oxisol, according to the Soil Survey Staff, equivalent to Latossolo in the Brazilian soil classification system. Nitrogen adsorption isotherms at standard 77 K were measured using a Thermo Finnigan Sorptomatic 1990 gas sorption analyzer (Thermo Scientific, Waltham, MA). From the raw data a distributions of mass along a support was obtained to perform multifractal analysis. The probability distribution was constructed by dividing the values of the measure in a given segment by the sum of the measure in the whole scale range. The box-counting method was employed to perform multifractal analysis. All the analyzed N2 adsorption isotherms behave like a multifractal system. The singularity spectra, f(α), showed asymmetric concave down parabolic shapes, with a greater tendency toward the left side, where moments

  2. A modified Langmuir-Freundlich isotherm model for simulating pH-dependent adsorption effects

    NASA Astrophysics Data System (ADS)

    Jeppu, Gautham P.; Clement, T. Prabhakar

    2012-03-01

    Analytical isotherm equations such as Langmuir and Freundlich isotherms are widely used for modeling adsorption data. However, these isotherms are primarily useful for simulating data collected at a fixed pH value and cannot be easily adapted to simulate pH-dependent adsorption effects. Therefore, most adsorption studies currently use numerical surface-complexation models (SCMs), which are more complex and time consuming than traditional analytical isotherm models. In this work, we propose a new analytical isotherm model, identified as the modified Langmuir-Freundlich (MLF) isotherm, which can be used to simulate pH-dependent adsorption. The MLF isotherm uses a linear correlation between pH and affinity coefficient values. We validated the proposed MLF isotherm by predicting arsenic adsorption onto two different types of sorbents: pure goethite and goethite-coated sand. The MLF model gave good predictions for both experimental and surface complexation-model predicted datasets for these two sorbents. The proposed analytical isotherm framework can help reduce modeling complexity, model development time, and computational efforts. One of the limitations of the proposed method is that it is currently valid only for single-component systems. Furthermore, the model requires a system-specific pH. vs. affinity coefficient relation. Despite these limitations, the approach provides a promising analytical framework for simulating pH-dependent adsorption effects.

  3. Isotherm, kinetic, and thermodynamic studies on Hg(II) adsorption from aqueous solution by silica- multiwall carbon nanotubes.

    PubMed

    Saleh, Tawfik A

    2015-11-01

    Silica combined with 2% multiwall carbon nanotubes (SiO2-CNT) was synthesized and characterized. Its sorption efficacy was investigated for the Hg(II) removal from an aqueous solution. The effect of pH on the percentage removal by the prepared material was examined in the range from 3 to 7. The adsorption kinetics were well fitted by using a pseudo-second-order model at various initial Hg(II) concentrations with R (2) of >0.99. The experimental data were plotted using the interparticle diffusion model, which indicated that the interparticle diffusion is not the only rate-limiting step. The data is well described by the Freundlich isotherm equation. The activation energy (Ea) for adsorption was 12.7 kJ mol(-1), indicating the process is to be physisorption. Consistent with an endothermic process, an increase in the temperature resulted in increasing mercury removal with a ∆H(o) of 13.3 kJ/mol and a ∆S(o) 67.5 J/mol K. The experimental results demonstrate that the combining of silica and nanotubes is a promising alternative material, which can be used to remove the mercury from wastewaters. PMID:26087931

  4. Isotherm, kinetic, and thermodynamic studies on Hg(II) adsorption from aqueous solution by silica- multiwall carbon nanotubes.

    PubMed

    Saleh, Tawfik A

    2015-11-01

    Silica combined with 2% multiwall carbon nanotubes (SiO2-CNT) was synthesized and characterized. Its sorption efficacy was investigated for the Hg(II) removal from an aqueous solution. The effect of pH on the percentage removal by the prepared material was examined in the range from 3 to 7. The adsorption kinetics were well fitted by using a pseudo-second-order model at various initial Hg(II) concentrations with R (2) of >0.99. The experimental data were plotted using the interparticle diffusion model, which indicated that the interparticle diffusion is not the only rate-limiting step. The data is well described by the Freundlich isotherm equation. The activation energy (Ea) for adsorption was 12.7 kJ mol(-1), indicating the process is to be physisorption. Consistent with an endothermic process, an increase in the temperature resulted in increasing mercury removal with a ∆H(o) of 13.3 kJ/mol and a ∆S(o) 67.5 J/mol K. The experimental results demonstrate that the combining of silica and nanotubes is a promising alternative material, which can be used to remove the mercury from wastewaters.

  5. Use of solid waste for chemical stabilization: Adsorption isotherms and {sup 13}C solid-state NMR study of hazardous organic compounds sorbed on coal fly ash

    SciTech Connect

    Netzel, D.A.; Lane, D.C.; Rovani, J.F.; Cox, J.D.; Clark, J.A.; Miknis, F.P.

    1993-09-01

    Adsorption of hazardous organic compounds on the Dave Johnston plant fly ash is described. Fly ash from Dave Johnston and Laramie River power plants were characterized using elemental, x-ray, and {sup 29}Si NMR; the Dave Johnston (DJ) fly ash had higher quartz contents, while the Laramie River fly ash had more monomeric silicate anions. Adsorption data for hydroaromatics and chlorobenzenes indicate that the adsorption capacity of DJ coal fly ash is much less than that of activated carbon by a factor of >3000; but it is needed to confirm that solid-gas and solid-liquid equilibrium isotherms can indeed be compared. However, for pyridine, pentachlorophenol, naphthalene, and 1,1,2,2-tetrachloroethane, the DJ fly ash appears to adsorb these compounds nearly as well as activated carbon. {sup 13}C NMR was used to study the adsorption of hazardous org. cpds on coal fly ash; the nuclear spin relaxation times often were very long, resulting in long experimental times to obtain a spectrum. Using a jumbo probe, low concentrations of some hazardous org. cpds could be detected; for pentachlorophenol adsorbed onto fly ash, the chemical shift of the phenolic carbon was changed. Use of NMR to study the adsorption needs further study.

  6. Effect of pore blockage on adsorption isotherms and dynamics: Anomalous adsorption of iodine on activated carbon

    SciTech Connect

    Bhatia, S.K.; Liu, F.; Arvind, G.

    2000-04-18

    Isotherm hysteresis and pore-clocking effects of trapped molecules on adsorption dynamics is studied here, using the iodine-carbon system in the 300--343 K temperature range. It is found that a portion of the iodine is strongly adsorbed, and does not desorb, even over very long time scales, while the remainder adsorbs reversibly as a homogeneous monolayer with a Langmuirian isotherm in mesopores. The strongly adsorbed iodine appears to adsorb in micropores and at the mesopore mouths, hindering uptake of the reversible iodine. The uptake data for the adsorption and desorption dynamics of the reversible part is found to be best explained by means of a pore mouth resistance control mechanism. it is concluded that the dynamics of the adsorption and desorption at the pore mouth is important at early stages of the process.

  7. Characterizing Nitrogen adsorption and desorption isotherms in soils using multifractal analysis

    NASA Astrophysics Data System (ADS)

    Paz Ferreiro, Jorge; Miranda, José G. V.; Vidal Vázquez, Eva

    2010-05-01

    The specific surface area is an attribute known to characterize the soil ability to retain and transport nutrients and water. A number of studies have shown that specific surface area correlates cation exchange capacity, organic matter content, water retention, aggregate stability and clay swelling. In the past fractal theory has been widely used to study different gas adsorption isotherms like water vapour and nitrogen adsorption isotherms. More recently we have shown that nitrogen adsorption isotherms showed multifractal nature. In this work, both N2 adsorption and desorption isotherms measured in a Mollisol were examined as a probability measure using the multifractal formalism in order to determinate its possible multifractal behaviour. Soil samples were collected in two different series of an Argiudoll located in the north of Buenos Aires and in the south of Santa Fe provinces, Argentina. Two treatments of each soil series were sampled at three depths, without replication, resulting in six samples per soil series and a total of twelve samples analyzed. Multifractal analysis was performed using the box counting method. Both, the N2 adsorption and desorption isotherms exhibited a well defined scaling behaviour indicating a fully developed multifractal structure of each isotherm branch. The singularity spectra and Rényi dimension spectra obtained for adsorption and also for desorption isotherms had shapes similar to the spectra of multifractal measures and several parameters were extracted from these spectra. The capacity dimension, D0, for both N2 adsorption and desorption data sets were not significantly different from 1.00. However, nitrogen adsorption and desorption data showed significantly different values of entropy dimension, D1, and correlation dimension, D2. For instance, entropy dimension values extracted from multifractal spectra of adsorption isotherms were on average 0.578 and varied from 0.501 to 0.666. In contrast, the corresponding figures for

  8. Immobilization of Acetobacter aceti on cellulose ion exchangers: adsorption isotherms

    SciTech Connect

    Bar, R.; Gainer, J.L.; Kirwan, D.J.

    1986-08-01

    The adsorptive behavior of cells of Acetobacter aceti, ATCC 23746, on DEAE-, TEAE-, and DEHPAE-cellulose ion exchangers in a modified Hoyer's medium at 30 degrees Centigrade was investigated. The maximum observed adsorption capacities varied from 46 to 64 mg dry wt/g resin. The Langmuir isotherm form was used to fit the data, since the cells formed a monolayer on the resin and exhibited saturation. The equilibrium constant in the Langmuir expression was qualitatively correlated with the surface charge density of the resin. The adsorption was also ''normalized'' by considering the ionic capacities of the resins. The exceptionally high normalized adsorption capacity of ECTEOLA-cellulose, 261 mg dry/meq, may be explained by an interaction between the cell wall and the polyglyceryl chains of the exchanging groups in addition to the electrostatic effects. The effect of pH on the bacterial adsorption capacity of ECTEOLA-, TEAE-, and phosphate-cellulose resins was studied and the pH of the bacteria was estimated to be 3.0. 17 references.

  9. Derivation of the Freundlich Adsorption Isotherm from Kinetics

    ERIC Educational Resources Information Center

    Skopp, Joseph

    2009-01-01

    The Freundlich adsorption isotherm is a useful description of adsorption phenomena. It is frequently presented as an empirical equation with little theoretical basis. In fact, a variety of derivations exist. Here a new derivation is presented using the concepts of fractal reaction kinetics. This derivation provides an alternative basis for…

  10. Isotherms for Water Adsorption on Molecular Sieve 3A: Influence of Cation Composition

    SciTech Connect

    Lin, Ronghong; Ladshaw, Austin; Nan, Yue; Liu, Jiuxu; Yiacoumi, Sotira; Tsouris, Costas; DePaoli, David W.; Tavlarides, Lawrence L.

    2015-06-16

    This study is part of our continuing efforts to address engineering issues related to the removal of tritiated water from off-gases produced in used nuclear fuel reprocessing facilities. In the current study, adsorption equilibrium of water on molecular sieve 3A beads was investigated. Adsorption isotherms for water on the UOP molecular sieve 3A were measured by a continuous-flow adsorption system at 298, 313, 333, and 353 K. Experimental data collected were analyzed by the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm model. The K+/Na+ molar ratio of this particular type of molecular sieve 3A was ~4:6. Our results showed that the GSTA isotherm model worked very well to describe the equilibrium behavior of water adsorption on molecular sieve 3A. The optimum number of parameters for the current experimental data was determined to be a set of four equilibrium parameters. This result suggests that the adsorbent crystals contain four energetically distinct adsorption sites. In addition, it was found that water adsorption on molecular sieve 3A follows a three-stage adsorption process. This three-stage adsorption process confirmed different water adsorption sites in molecular sieve crystals. In addition, the second adsorption stage is significantly affected by the K+/Na+ molar ratio. In this stage, the equilibrium adsorption capacity at a given water vapor pressure increases as the K+/Na+ molar ratio increases.

  11. Isotherms for Water Adsorption on Molecular Sieve 3A: Influence of Cation Composition

    DOE PAGES

    Lin, Ronghong; Ladshaw, Austin; Nan, Yue; Liu, Jiuxu; Yiacoumi, Sotira; Tsouris, Costas; DePaoli, David W.; Tavlarides, Lawrence L.

    2015-06-16

    This study is part of our continuing efforts to address engineering issues related to the removal of tritiated water from off-gases produced in used nuclear fuel reprocessing facilities. In the current study, adsorption equilibrium of water on molecular sieve 3A beads was investigated. Adsorption isotherms for water on the UOP molecular sieve 3A were measured by a continuous-flow adsorption system at 298, 313, 333, and 353 K. Experimental data collected were analyzed by the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm model. The K+/Na+ molar ratio of this particular type of molecular sieve 3A was ~4:6. Our results showed that themore » GSTA isotherm model worked very well to describe the equilibrium behavior of water adsorption on molecular sieve 3A. The optimum number of parameters for the current experimental data was determined to be a set of four equilibrium parameters. This result suggests that the adsorbent crystals contain four energetically distinct adsorption sites. In addition, it was found that water adsorption on molecular sieve 3A follows a three-stage adsorption process. This three-stage adsorption process confirmed different water adsorption sites in molecular sieve crystals. In addition, the second adsorption stage is significantly affected by the K+/Na+ molar ratio. In this stage, the equilibrium adsorption capacity at a given water vapor pressure increases as the K+/Na+ molar ratio increases.« less

  12. Adsorption isotherms, kinetics and thermodynamic studies towards understanding the interaction between cross-linked alginate-guar gum matrix and chymotrypsin.

    PubMed

    Woitovich Valetti, Nadia; Picó, Guillermo

    2016-02-15

    The adsorption kinetics of chymotrypsin, a pancreatic serine protease, onto an alginate-gum guar matrix cross-linked with epichlorohydrin has been performed using a batch-adsorption technique. The effect of various experimental parameters such as pH, salt presence, contact time and temperature were investigated. The pseudo-first-order and pseudo-second-order kinetic models were used to describe the kinetic data which shows that the adsorption of the enzyme followed the pseudo-second-order rate expression. The Langmuir, Freundlich and Hill adsorption isotherm models were applied to describe the equilibrium isotherms, and the isotherm constants were determined. It was found that Hill model was more suitable for our data because the isotherm data showed a sigmoidal behavior with the free enzyme concentration increasing in equilibrium. At 8°C and at pH 5.0, 1g hydrate matrix adsorbed about 7mg of chymotrypsin. In the desorption process 80% of the biological activity of chymotrypsin was recovered under the condition of 50mM phosphate buffer, pH 7.00-500mM NaCl. When successive cycles of adsorption/washing/desorption were performed, it was observed that the matrix remained functional until the fourth cycle of repeated batch enzyme adsorption. These results are important in terms of diminishing of cost and waste generation. PMID:26849187

  13. Adsorption isotherms, kinetics and thermodynamic studies towards understanding the interaction between cross-linked alginate-guar gum matrix and chymotrypsin.

    PubMed

    Woitovich Valetti, Nadia; Picó, Guillermo

    2016-02-15

    The adsorption kinetics of chymotrypsin, a pancreatic serine protease, onto an alginate-gum guar matrix cross-linked with epichlorohydrin has been performed using a batch-adsorption technique. The effect of various experimental parameters such as pH, salt presence, contact time and temperature were investigated. The pseudo-first-order and pseudo-second-order kinetic models were used to describe the kinetic data which shows that the adsorption of the enzyme followed the pseudo-second-order rate expression. The Langmuir, Freundlich and Hill adsorption isotherm models were applied to describe the equilibrium isotherms, and the isotherm constants were determined. It was found that Hill model was more suitable for our data because the isotherm data showed a sigmoidal behavior with the free enzyme concentration increasing in equilibrium. At 8°C and at pH 5.0, 1g hydrate matrix adsorbed about 7mg of chymotrypsin. In the desorption process 80% of the biological activity of chymotrypsin was recovered under the condition of 50mM phosphate buffer, pH 7.00-500mM NaCl. When successive cycles of adsorption/washing/desorption were performed, it was observed that the matrix remained functional until the fourth cycle of repeated batch enzyme adsorption. These results are important in terms of diminishing of cost and waste generation.

  14. Determination of gas phase adsorption isotherms--a simple constant volume method.

    PubMed

    Kim, Daekeun; Cai, Zhangli; Sorial, George A

    2006-08-01

    Single and ternary solute gas phase adsorption isotherms were conducted in this study to evaluate the effectiveness of a simple constant volume method, which was utilized by using Tedlar gas sampling bags as a constant volume batch reactor. For this purpose, gas phase adsorption of toluene, methyl ethyl ketone (MEK), and methyl isobutyl ketone (MIBK) on two types of activated carbons, BPL-bituminous base and OVC--coconut base, were investigated. For the single solute adsorption, the experimental adsorption data were found to be well correlated with Freundlich and Myers adsorption equations. The pore size distribution of adsorbents was found to affect their adsorption capacities; its effect was dependant on the solute concentration. The ternary adsorption experimental isotherms were accurately predicted by using the well-known model, i.e., ideal adsorbed solution theory (IAST).

  15. Moisture adsorption isotherms and glass transition temperature of pectin.

    PubMed

    Basu, Santanu; Shivhare, U S; Muley, S

    2013-06-01

    The moisture adsorption isotherms of low methoxyl pectin were determined at 30-70°C and water activity ranging from 0.11 to 0.94. The moisture adsorption isotherms revealed that the equilibrium moisture content increased with water activity. Increase in temperature, in general, resulted in decreased equilibrium moisture content. However in some cases, equilibrium moisture content values increased with temperature at higher water activities. Selected sorption models (GAB, Halsey, Henderson, Oswin, modified Oswin) were tested for describing the adsorption isotherms. Parameters of each sorption models were determined by nonlinear regression analysis. Oswin model gave the best fit for pectin sorption behaviour. Isosteric heat of sorption decreased with increase in moisture content and varied between 14.607 and 0.552 kJ/mol. Glass transition temperature decreased with increase in moisture content of pectin. PMID:24425957

  16. Adsorption kinetics and isotherms of pesticides onto activated carbon-cloth.

    PubMed

    Ayranci, Erol; Hoda, Numan

    2005-09-01

    Adsorption of pesticides ametryn, aldicarb, dinoseb and diuron from aqueous solution onto high specific area activated carbon-cloth was studied. Kinetics of adsorption was followed by in situ UV-spectroscopy and the data were treated according to various rate models. The extent of adsorption was determined at the end of 125 min adsorption period. Rate constants and the extent of adsorption for the four pesticides were found to follow the order: dinoseb > ametryn > diuron > aldicarb. Adsorption isotherms were derived at 25 degrees C on the basis of batch analysis. Isotherm data were treated according to Langmuir and Freundlich models. The fits of experimental data to these equations were examined. The types of interactions between the surface and pesticide molecules were discussed. PMID:16083766

  17. Isotherms for adsorption of cellobiohydrolase I and II from Trichoderma reesei on microcrystalline cellulose

    SciTech Connect

    Medve, J.; Tjerneld, F.; Stahlberg, J.

    1997-04-01

    Adsorption to microcrystalline cellulose (Avicel) of pure cellobiohydrolase I and II (CBH I and CBH II) from Trichoderma reesei has been studied. Adsorption isotherms of the enzymes were measured at 4{degree}C using CBH I and CBH II alone and in reconstituted equimolar mixtures. Several models (Langmuir, Freundlich, Temkin, Jovanovic) were tested to describe the experimental adsorption isotherms. The isotherms did not follow the basic (one site) Langmuir equation that has often been used to describe adsorption isotherms of cellulases; correlation coefficients (R{sup 2}) were only 0.926 and 0.947, for CBH I and II, respectively. The experimental isotherms were best described by a model of Langmuir type with two adsorption sites and by a combined Langmuir-Freundlich model (analogous to the Hill equation); using these models the correlation coefficients were in most cases higher than 0.995. Apparent binding parameters derived from the two sites Langmuir model indicated stronger binding of CBH II compared to CBH I; the distribution coefficients were 20.7 and 3.7 L/g for the two enzymes, respectively. The binding capacity was higher for CBH I than for CBH II. The isotherms when analyzed with the combined model indicated presence of unequal binding sites on cellulose and/or negative cooperativity in the binding of the enzyme molecules. 39 refs., 3 figs., 3 tabs.

  18. Adsorption of Cd(II) by Mg-Al-CO3- and magnetic Fe3O4/Mg-Al-CO3-layered double hydroxides: Kinetic, isothermal, thermodynamic and mechanistic studies.

    PubMed

    Shan, Ran-ran; Yan, Liang-guo; Yang, Kun; Hao, Yuan-feng; Du, Bin

    2015-12-15

    Understanding the adsorption mechanisms of metal cations on the surfaces of solids is important for determining the fate of these metals in water and wastewater treatment. The adsorption kinetic, isothermal, thermodynamic and mechanistic properties of cadmium (Cd(II)) in an aqueous solution containing Mg-Al-CO3- and magnetic Fe3O4/Mg-Al-CO3-layered double hydroxide (LDH) were studied. The results demonstrated that the adsorption kinetic and isotherm data followed the pseudo-second-order model and the Langmuir equation, respectively. The adsorption process of Cd(II) was feasible, spontaneous and endothermic in nature. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy were used to explain the adsorption mechanisms. The characteristic XRD peaks and FTIR bands of CdCO3 emerged in the LDH spectra after Cd(II) adsorption, which indicated that the adsorption of Cd(II) by LDHs occurred mainly via CdCO3 precipitation, surface adsorption and surface complexation. Furthermore, the magnetic Fe3O4/Mg-Al-CO3-LDH can be quickly and easily separated using a magnet before and after the adsorption process.

  19. Comparison of multifractal parameters form adsorption isotherms, desorption isotherms and mercury intrusion curves

    NASA Astrophysics Data System (ADS)

    Paz-Ferreiro, Jorge; Mon, Rodolfo; Vidal Vázquez, Eva

    2013-04-01

    The soil pore space is composed of a continuum of pores extremely variable in size, which range from equivalent diameter sizes smaller than nanometers to an upper limit of the order of centimeters. So, it is quite typical for soil pore space to display a size range of more than a factor of 106 in scale. Nitrogen sorption and mercury injection provide pores size distributions in the range from about 0.1 to 0.001 μm and 150 to 0.005 μm, respectively. The aims of this study were to evaluate the scaling properties of nitrogen adsorption isotherms (NAI), nitrogen desorption isotherms (NDI) and mercury intrusion porosimetry (MIP) curves of agricultural soils from "La Pampa húmeda", in the north of Buenos Aires and south of Santa Fé provinces, Argentina. Both NAIs, NDIs and MIPs exhibited multifractal behavior but its scaling properties were different so that the multifractality index, assessed by the width of the generalized dimension and the singularity spectra ranked as follows: NAI > NDI > MIP. Also, parameterization by the Hurst exponent indicates NAIs were less persistent than NDIs and in turn, these were less persistent than MIPs. The multfractal approach was useful to characterize the heterogeneity of various domains of the soil nano- micro- and mesopore system at the scale of small aggregates.

  20. Predicting heavy metals' adsorption edges and adsorption isotherms on MnO2 with the parameters determined from Langmuir kinetics.

    PubMed

    Hu, Qinghai; Xiao, Zhongjin; Xiong, Xinmei; Zhou, Gongming; Guan, Xiaohong

    2015-01-01

    Although surface complexation models have been widely used to describe the adsorption of heavy metals, few studies have verified the feasibility of modeling the adsorption kinetics, edge, and isotherm data with one pH-independent parameter. A close inspection of the derivation process of Langmuir isotherm revealed that the equilibrium constant derived from the Langmuir kinetic model, KS-kinetic, is theoretically equivalent to the adsorption constant in Langmuir isotherm, KS-Langmuir. The modified Langmuir kinetic model (MLK model) and modified Langmuir isotherm model (MLI model) incorporating pH factor were developed. The MLK model was employed to simulate the adsorption kinetics of Cu(II), Co(II), Cd(II), Zn(II) and Ni(II) on MnO2 at pH3.2 or 3.3 to get the values of KS-kinetic. The adsorption edges of heavy metals could be modeled with the modified metal partitioning model (MMP model), and the values of KS-Langmuir were obtained. The values of KS-kinetic and KS-Langmuir are very close to each other, validating that the constants obtained by these two methods are basically the same. The MMP model with KS-kinetic constants could predict the adsorption edges of heavy metals on MnO2 very well at different adsorbent/adsorbate concentrations. Moreover, the adsorption isotherms of heavy metals on MnO2 at various pH levels could be predicted reasonably well by the MLI model with the KS-kinetic constants.

  1. Highly efficient ultrasonic-assisted removal of Hg(II) ions on graphene oxide modified with 2-pyridinecarboxaldehyde thiosemicarbazone: Adsorption isotherms and kinetics studies.

    PubMed

    Tadjarodi, Azadeh; Moazen Ferdowsi, Somayeh; Zare-Dorabei, Rouholah; Barzin, Ahmad

    2016-11-01

    A novel adsorbent, based on modifying graphene oxide (GO) chemically with 2-pyridinecarboxaldehyde thiosemicarbazone (2-PTSC) as ligand, was designed by facile process for removal of Hg(II) from aqueous solution. Characterization of the adsorbent was performed using various techniques, such as FT-IR, XRD, XPS, SEM and AFM analysis. The adsorption capacity was affected by variables such as adsorbent dosage, pH solution, Hg(2+) initial concentration and sonicating time. These variables were optimized by rotatable central composite design (CCD) under response surface methodology (RSM). The predictive model for Hg(II) adsorption was constructed and applied to find the best conditions at which the responses were maximized. In this conditions, the adsorption capacity of this adsorbent for Hg(2+) ions was calculated to be 309mgg(-1) that was higher than that of GO. Appling the ultrasound power combined with adsorption method was very efficient in shortening the removal time of Hg(2+) ions by enhancing the dispersion of adsorbent and metal ions in solution and effective interactions among them. The adsorption process was well described by second-order kinetic and Langmuir isotherm model in which the maximum adsorption capacity (Qm) was found to be 555mgg(-1) for adsorption of Hg(2+) ions over the obtained adsorbent. The performance of adsorbent was examined on the real wastewaters and confirmed the applicability of adsorbent for practical applications. PMID:27245963

  2. A study of the adsorption of the amphiphilic penicillins cloxacillin and dicloxacillin onto human serum albumin using surface tension isotherms

    NASA Astrophysics Data System (ADS)

    Barbosa, Silvia; Leis, David; Taboada, Pablo; Attwood, David; Mosquera, Victor

    The interaction of human serum albumin (HSA) with two structurally similar anionic amphiphilic penicillins, cloxacillin and dicloxacillin, at 25°C has been examined by surface tension measurements under conditions at which the HSA molecule was positively (pH 4.5) or negatively charged (pH 7.4). Measurements were at fixed HSA concentrations (0.0125 and 0.125% w/v) and at drug concentrations over a range including, where possible, the critical micelle concentration (cmc). Interaction between anionic drugs and positively charged HSA at pH 7.4 resulted in an increase of the cmc of each drug as a consequence of its removal from solution by adsorption. Limited data for cloxacillin at pH 4.5 indicated an apparent decrease of the cmc in the presence of HSA suggesting a facilitation of the aggregation by association with the protein. Changes in the surface tension-log (drug concentration) plots in the presence of HSA have been discussed in terms of the adsorption of drug at the air-solution and protein-solution interfaces. Standard free energy changes associated with the micellization of both drugs and their adsorption at the air-solution interface have been calculated and compared.

  3. Cadmium-109 Radioisotope Adsorption onto Polypyrrole Coated Sawdust of Dryobalanops aromatic: Kinetics and Adsorption Isotherms Modelling

    PubMed Central

    Olatunji, Michael Adekunle; Khandaker, Mayeen Uddin; Amin, Yusoff Mohd; Mahmud, Habibun Nabi Muhammad Ekramul

    2016-01-01

    A radiotracer study was conducted to investigate the removal characteristics of cadmium (109Cd) from aqueous solution by polypyrrole/ sawdust composite. Several factors such as solution pH, sorbent dosage, initial concentration, contact time, temperature and interfering metal ions were found to have influence on the adsorption process. The kinetics of adsorption was relatively fast, reaching equilibrium within 3 hours. A lowering of the solution pH reduced the removal efficiency from 99.3 to ~ 46.7% and an ambient temperature of 25°C was found to be optimum for maximum adsorption. The presence of sodium and potassium ions inhibited 109Cd removal from its aqueous solution. The experimental data for 109Cd adsorption showed a very good agreement with the Langmuir isotherm and a pseudo-first order kinetic model. The surface condition of the adsorbent before and after cadmium loading was investigated using BET, FESEM and FTIR. Considering the low cost of the precursor’s materials and the toxicity of 109Cd radioactive metal, polypyrrole synthesized on the sawdust of Dryobalanops aromatic could be used as an efficient adsorbent for the removal of 109Cd radioisotope from radionuclide-containing effluents. PMID:27706232

  4. Isotherm and kinetics study of malachite green adsorption onto copper nanowires loaded on activated carbon: artificial neural network modeling and genetic algorithm optimization.

    PubMed

    Ghaedi, M; Shojaeipour, E; Ghaedi, A M; Sahraei, Reza

    2015-05-01

    In this study, copper nanowires loaded on activated carbon (Cu-NWs-AC) was used as novel efficient adsorbent for the removal of malachite green (MG) from aqueous solution. This new material was synthesized through simple protocol and its surface properties such as surface area, pore volume and functional groups were characterized with different techniques such XRD, BET and FESEM analysis. The relation between removal percentages with variables such as solution pH, adsorbent dosage (0.005, 0.01, 0.015, 0.02 and 0.1g), contact time (1-40min) and initial MG concentration (5, 10, 20, 70 and 100mg/L) was investigated and optimized. A three-layer artificial neural network (ANN) model was utilized to predict the malachite green dye removal (%) by Cu-NWs-AC following conduction of 248 experiments. When the training of the ANN was performed, the parameters of ANN model were as follows: linear transfer function (purelin) at output layer, Levenberg-Marquardt algorithm (LMA), and a tangent sigmoid transfer function (tansig) at the hidden layer with 11 neurons. The minimum mean squared error (MSE) of 0.0017 and coefficient of determination (R(2)) of 0.9658 were found for prediction and modeling of dye removal using testing data set. A good agreement between experimental data and predicted data using the ANN model was obtained. Fitting the experimental data on previously optimized condition confirm the suitability of Langmuir isotherm models for their explanation with maximum adsorption capacity of 434.8mg/g at 25°C. Kinetic studies at various adsorbent mass and initial MG concentration show that the MG maximum removal percentage was achieved within 20min. The adsorption of MG follows the pseudo-second-order with a combination of intraparticle diffusion model. PMID:25699703

  5. Isotherm and kinetics study of malachite green adsorption onto copper nanowires loaded on activated carbon: artificial neural network modeling and genetic algorithm optimization.

    PubMed

    Ghaedi, M; Shojaeipour, E; Ghaedi, A M; Sahraei, Reza

    2015-05-01

    In this study, copper nanowires loaded on activated carbon (Cu-NWs-AC) was used as novel efficient adsorbent for the removal of malachite green (MG) from aqueous solution. This new material was synthesized through simple protocol and its surface properties such as surface area, pore volume and functional groups were characterized with different techniques such XRD, BET and FESEM analysis. The relation between removal percentages with variables such as solution pH, adsorbent dosage (0.005, 0.01, 0.015, 0.02 and 0.1g), contact time (1-40min) and initial MG concentration (5, 10, 20, 70 and 100mg/L) was investigated and optimized. A three-layer artificial neural network (ANN) model was utilized to predict the malachite green dye removal (%) by Cu-NWs-AC following conduction of 248 experiments. When the training of the ANN was performed, the parameters of ANN model were as follows: linear transfer function (purelin) at output layer, Levenberg-Marquardt algorithm (LMA), and a tangent sigmoid transfer function (tansig) at the hidden layer with 11 neurons. The minimum mean squared error (MSE) of 0.0017 and coefficient of determination (R(2)) of 0.9658 were found for prediction and modeling of dye removal using testing data set. A good agreement between experimental data and predicted data using the ANN model was obtained. Fitting the experimental data on previously optimized condition confirm the suitability of Langmuir isotherm models for their explanation with maximum adsorption capacity of 434.8mg/g at 25°C. Kinetic studies at various adsorbent mass and initial MG concentration show that the MG maximum removal percentage was achieved within 20min. The adsorption of MG follows the pseudo-second-order with a combination of intraparticle diffusion model.

  6. Isotherm and kinetics study of malachite green adsorption onto copper nanowires loaded on activated carbon: Artificial neural network modeling and genetic algorithm optimization

    NASA Astrophysics Data System (ADS)

    Ghaedi, M.; Shojaeipour, E.; Ghaedi, A. M.; Sahraei, Reza

    2015-05-01

    In this study, copper nanowires loaded on activated carbon (Cu-NWs-AC) was used as novel efficient adsorbent for the removal of malachite green (MG) from aqueous solution. This new material was synthesized through simple protocol and its surface properties such as surface area, pore volume and functional groups were characterized with different techniques such XRD, BET and FESEM analysis. The relation between removal percentages with variables such as solution pH, adsorbent dosage (0.005, 0.01, 0.015, 0.02 and 0.1 g), contact time (1-40 min) and initial MG concentration (5, 10, 20, 70 and 100 mg/L) was investigated and optimized. A three-layer artificial neural network (ANN) model was utilized to predict the malachite green dye removal (%) by Cu-NWs-AC following conduction of 248 experiments. When the training of the ANN was performed, the parameters of ANN model were as follows: linear transfer function (purelin) at output layer, Levenberg-Marquardt algorithm (LMA), and a tangent sigmoid transfer function (tansig) at the hidden layer with 11 neurons. The minimum mean squared error (MSE) of 0.0017 and coefficient of determination (R2) of 0.9658 were found for prediction and modeling of dye removal using testing data set. A good agreement between experimental data and predicted data using the ANN model was obtained. Fitting the experimental data on previously optimized condition confirm the suitability of Langmuir isotherm models for their explanation with maximum adsorption capacity of 434.8 mg/g at 25 °C. Kinetic studies at various adsorbent mass and initial MG concentration show that the MG maximum removal percentage was achieved within 20 min. The adsorption of MG follows the pseudo-second-order with a combination of intraparticle diffusion model.

  7. A model free method for estimation of complicated adsorption isotherms in liquid chromatography.

    PubMed

    Forssén, Patrik; Fornstedt, Torgny

    2015-08-28

    Here we show that even extremely small variations in the adsorption isotherm can have a tremendous effect on the shape of the overloaded elution profiles and that the earlier in the adsorption isotherms the variation take place, the larger its impact on the shape of the elution profile. These variations are so small that they can be "hidden" by the discretization and in the general experimental noise when using traditional experimental methods, such as frontal analysis, to measure adsorption isotherms. But as the effects of these variations are more clearly visible in the elution profiles, the Inverse Method (IM) of adsorption isotherm estimation is an option. However, IM usually requires that one selects an adsorption isotherm model prior to the estimation process. Here we show that even complicated models might not be able to estimate the adsorption isotherms with multiple inflection points that small variations might give rise to. We therefore developed a modified IM that, instead of fixed adsorption isotherm models, uses monotone piecewise interpolation. We first validated the method with synthetic data and showed that it can be used to estimate an adsorption isotherm, which accurately predicts an extremely "strange" elution profile. For this case it was impossible to estimate the adsorption isotherm using IM with a fixed adsorption model. Finally, we will give an example of a real chromatographic system where adsorption isotherm with inflection points is estimated by the modified IM.

  8. Isotherms and kinetic study of dihydrogen and hydrogen phosphate ions (H{2}PO{4}- and HPO{4}2-) adsorption onto crushed plant matter of the semi-arid zones of Morocco: Asphodelus microcarpus, Asparagus albus and Senecio anthophorbium

    NASA Astrophysics Data System (ADS)

    Chiban, M.; Benhima, H.; Saadi, B.; Nounah, A.; Sinan, F.

    2005-03-01

    In the present work H{2}PO4- and HPO42- ions adsorption onto organic matter (OM) obtained from ground dried three plants growing in arid zones of Morocco has been studied. The adsorption process is affected by various parameters such as contact time, particle size and initial concentration of phosphate solution (Ci ≤ 30 mg/l). The uptake of both ions is increased by increasing the concentration of them selves. The retention of phosphate ions by Asphodelus microcarpus, Asparagus albus are well defined by several isotherms such as the Langmuir, Temkin and Freundlich.

  9. Adsorption of pharmaceuticals onto activated carbon fiber cloths - Modeling and extrapolation of adsorption isotherms at very low concentrations.

    PubMed

    Fallou, Hélène; Cimetière, Nicolas; Giraudet, Sylvain; Wolbert, Dominique; Le Cloirec, Pierre

    2016-01-15

    Activated carbon fiber cloths (ACFC) have shown promising results when applied to water treatment, especially for removing organic micropollutants such as pharmaceutical compounds. Nevertheless, further investigations are required, especially considering trace concentrations, which are found in current water treatment. Until now, most studies have been carried out at relatively high concentrations (mg L(-1)), since the experimental and analytical methodologies are more difficult and more expensive when dealing with lower concentrations (ng L(-1)). Therefore, the objective of this study was to validate an extrapolation procedure from high to low concentrations, for four compounds (Carbamazepine, Diclofenac, Caffeine and Acetaminophen). For this purpose, the reliability of the usual adsorption isotherm models, when extrapolated from high (mg L(-1)) to low concentrations (ng L(-1)), was assessed as well as the influence of numerous error functions. Some isotherm models (Freundlich, Toth) and error functions (RSS, ARE) show weaknesses to be used as an adsorption isotherms at low concentrations. However, from these results, the pairing of the Langmuir-Freundlich isotherm model with Marquardt's percent standard of deviation was evidenced as the best combination model, enabling the extrapolation of adsorption capacities by orders of magnitude. PMID:26606322

  10. Optimization, isotherm, kinetic and thermodynamic studies of Pb(II) ions adsorption onto N-maleated chitosan-immobilized TiO₂ nanoparticles from aqueous media.

    PubMed

    Shaker, Medhat A; Yakout, Amr A

    2016-02-01

    Chitosan, CS was chemically engineered by maleic anhydride via simple protocol to produce N-maleated chitosan, MCS which immobilized on anatase TiO2 to synthesize novel eco-friendly nanosorbent (51±3.8 nm), MCS@TiO2 for cost-effective and efficient removal of Pb(II) ions from aqueous media. The chemical structure, surface properties and morphology of MCS@TiO2 were recognized by FTIR, (1)H NMR, XRD, TEM, DLS and zeta-potential techniques. The relations between %removal of Pb(II) and different analytical parameters such as solution acidity (pH), MCS@TiO2 dosage, time of contact and initial Pb(II) concentration were optimized using response surface methodology (RSM) and Box-Behnken design (BBD) statistical procedures. The fitting of the experimental data to four different isotherm models at optimized conditions was carried out by various statistical treatments including the correlation coefficient (r), coefficient of determination (r(2)) and non-linear Chi-square (χ(2)) test analyses which all confirm the suitability of Langmuir model to explain the adsorption isotherm data. Also, statistics predicted that the pseudo-second-order model is the optimum kinetic model among four applied kinetic models to closely describe the rate equation of the adsorption process. Thermodynamics viewed the adsorption as endothermic and feasible physical process. EDTA could release the sorbed Pb(II) ions from MCS@TiO2 with a recovery above 92% after three sorption-desorption cycles. The novel synthesized nanosorbent is evidenced to be an excellent solid phase extractor for Pb(II) ions from wastewaters.

  11. Optimization, isotherm, kinetic and thermodynamic studies of Pb(II) ions adsorption onto N-maleated chitosan-immobilized TiO2 nanoparticles from aqueous media

    NASA Astrophysics Data System (ADS)

    Shaker, Medhat A.; Yakout, Amr A.

    2016-02-01

    Chitosan, CS was chemically engineered by maleic anhydride via simple protocol to produce N-maleated chitosan, MCS which immobilized on anatase TiO2 to synthesize novel eco-friendly nanosorbent (51 ± 3.8 nm), MCS@TiO2 for cost-effective and efficient removal of Pb(II) ions from aqueous media. The chemical structure, surface properties and morphology of MCS@TiO2 were recognized by FTIR, 1H NMR, XRD, TEM, DLS and zeta-potential techniques. The relations between %removal of Pb(II) and different analytical parameters such as solution acidity (pH), MCS@TiO2 dosage, time of contact and initial Pb(II) concentration were optimized using response surface methodology (RSM) and Box-Behnken design (BBD) statistical procedures. The fitting of the experimental data to four different isotherm models at optimized conditions was carried out by various statistical treatments including the correlation coefficient (r), coefficient of determination (r2) and non-linear Chi-square (χ2) test analyses which all confirm the suitability of Langmuir model to explain the adsorption isotherm data. Also, statistics predicted that the pseudo-second-order model is the optimum kinetic model among four applied kinetic models to closely describe the rate equation of the adsorption process. Thermodynamics viewed the adsorption as endothermic and feasible physical process. EDTA could release the sorbed Pb(II) ions from MCS@TiO2 with a recovery above 92% after three sorption-desorption cycles. The novel synthesized nanosorbent is evidenced to be an excellent solid phase extractor for Pb(II) ions from wastewaters.

  12. Optimization, isotherm, kinetic and thermodynamic studies of Pb(II) ions adsorption onto N-maleated chitosan-immobilized TiO₂ nanoparticles from aqueous media.

    PubMed

    Shaker, Medhat A; Yakout, Amr A

    2016-02-01

    Chitosan, CS was chemically engineered by maleic anhydride via simple protocol to produce N-maleated chitosan, MCS which immobilized on anatase TiO2 to synthesize novel eco-friendly nanosorbent (51±3.8 nm), MCS@TiO2 for cost-effective and efficient removal of Pb(II) ions from aqueous media. The chemical structure, surface properties and morphology of MCS@TiO2 were recognized by FTIR, (1)H NMR, XRD, TEM, DLS and zeta-potential techniques. The relations between %removal of Pb(II) and different analytical parameters such as solution acidity (pH), MCS@TiO2 dosage, time of contact and initial Pb(II) concentration were optimized using response surface methodology (RSM) and Box-Behnken design (BBD) statistical procedures. The fitting of the experimental data to four different isotherm models at optimized conditions was carried out by various statistical treatments including the correlation coefficient (r), coefficient of determination (r(2)) and non-linear Chi-square (χ(2)) test analyses which all confirm the suitability of Langmuir model to explain the adsorption isotherm data. Also, statistics predicted that the pseudo-second-order model is the optimum kinetic model among four applied kinetic models to closely describe the rate equation of the adsorption process. Thermodynamics viewed the adsorption as endothermic and feasible physical process. EDTA could release the sorbed Pb(II) ions from MCS@TiO2 with a recovery above 92% after three sorption-desorption cycles. The novel synthesized nanosorbent is evidenced to be an excellent solid phase extractor for Pb(II) ions from wastewaters. PMID:26520475

  13. Suitability of adsorption isotherms for predicting the retention capacity of active slag filters removing phosphorus from wastewater.

    PubMed

    Pratt, C; Shilton, A

    2009-01-01

    Active slag filters are an emerging technology for removing phosphorus (P) from wastewater. A number of researchers have suggested that adsorption isotherms are a useful tool for predicting P retention capacity. However, to date the appropriateness of using isotherms for slag filter design remains unverified due to the absence of benchmark data from a full-scale, field filter operated to exhaustion. This investigation compared the isotherm-predicted P retention capacity of a melter slag with the P adsorption capacity determined from a full-scale, melter slag filter which had reached exhaustion after five years of successfully removing P from waste stabilization pond effluent. Results from the standard laboratory batch test showed that P adsorption correlated more strongly with the Freundlich Isotherm (R(2)=0.97, P<0.01) than the Langmuir Isotherm, a similar finding to previous studies. However, at a P concentration of 10 mg/L, typical of domestic effluent, the Freundlich equation predicted a retention capacity of 0.014 gP/kg slag; markedly lower than the 1.23 gP/kg slag adsorbed by the field filter. Clearly, the result generated by the isotherm bears no resemblance to actual field capacity. Scanning electron microscopy analysis revealed porous, reactive secondary minerals on the slag granule surfaces from the field filter which were likely created by weathering. This slow weathering effect, which generates substantial new adsorption sites, is not accounted for by adsorption isotherms rendering them ineffective in slag filter design. PMID:19403982

  14. Determination of the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon using thermogravimetric analysis

    SciTech Connect

    Hsun-Yu Lin; Chung-Shin Yuan; Wei-Ching Chen; Chung-Hsuang Hung

    2006-11-15

    This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl{sub 2} was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl{sub 2} were 1.75, 0.688, and 0.230 mg of HgCl{sub 2} per gram of powdered activated carbon derived from carbon black at 30, 70, and 150{sup o} for 500 {mu}g/m{sup 3} of HgCl{sub 2}, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer-Emmett-eller (BET) models were used to simulate the adsorption of HgCl{sub 2}. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30{sup o}, whereas the Freundlich isotherm fit the experimental results better at 70 and 150{sup o}. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl{sub 2} by PAC-derived carbon black favored adsorption at various HgCl{sub 2} concentrations and temperatures. 35 refs., 7 figs., 3 tabs.

  15. Correlation of adsorption isotherms of hydrogen isotopes on mordenite adsorbents using reactive vacancy solution theory

    SciTech Connect

    Munakata, K.; Nakamura, A.; Kawamura, Y.

    2015-03-15

    The authors have applied the isotherm equations derived from the reactive vacancy solution theory (RVST) to correlation of experimental and highly non-ideal adsorption isotherms of hydrogen and deuterium on a mordenite adsorbent, and have examined the ability of the isotherm equations to match this correlation. Several isotherm equations such as Langmuir, Freundlich, Toth, Vacancy Solution Theory and so forth were also tested, but they did not work. For the Langmuir-Freundlich equation tests have indicated that its 'ability to correlate' of the adsorption isotherms is not satisfactory. For the multi-site Langmuir-Freundlich (MSLF) equation the correlation of the isotherms appears to be somewhat improved but remains unsatisfactory. The results show that the isotherm equations derived from RVST can better correlate the experimental isotherms.

  16. Heterogeneous three-site lattice model for adsorption of aromatics in ZSM-5 zeolites: Temperature dependence of adsorption isotherms

    SciTech Connect

    Narkiewicz-Michalek, J.; Szabelski, P.; Rudzinski, W.; Chiang, A.S.T.

    1999-08-31

    The three-site lattice model of collective localized adsorption of aromatics in ZSM-5 zeolites, presented in previous publications, is extended by taking into account the effects of energetic heterogeneity of the sites of the same type. The appropriate theoretical equations are derived and used for simultaneous description of the experimental adsorption isotherms and heats of adsorption of benzene and p-xylene in silicalite at 303 K. It is shown that taking into account this additional level of heterogeneity leads to a much better description of both the adsorption isotherms and the related heats of adsorption in these systems. The extended model also allows one to predict correctly the adsorption isotherms of benzene and p-xylene in silicalite at different temperatures using the parameters found at one temperature.

  17. Adsorption isotherms, kinetics, thermodynamics and desorption studies for uranium and thorium ions from aqueous solution by novel microporous composite P(HEMA-EP)

    NASA Astrophysics Data System (ADS)

    Akkaya, Recep; Akkaya, Birnur

    2013-03-01

    In this research, a novel composite, poly(2-hydroxyethylmethacrylate-expanded perlite) [P(HEMA-EP)], was synthesized and its adsorptive features were investigated. P(HEMA-EP)'s adsorptive features were evaluated for UO22+ and Th4+ ions in terms of the dependency upon the ion concentration, pH, temperature, and time. P(HEMA-EP) was able to bind UO22+ and Th4+ ions with strong chemical affinity. The adsorption results were fitted to the classical Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) sorption models. P(HEMA-EP) was also used to study the removal of UO22+ and Th4+ ions from aqueous solutions in a batch system. The adsorption capacity (XL) of UO22+ and Th4+ ions was found to be 0.29 and 0.44 mol kg-1, respectively. The kinetic data corresponds well to the pseudo-second-order equation. Changes in the enthalpy and entropy values demonstrated that the overall adsorption process was spontaneous (ΔG < 0), endothermic (ΔH > 0), and had increased entropy (ΔS > 0), as expected. The reusability of the composites was confirmed for five sequential reuses.

  18. The investigation of kinetic and isotherm of fluoride adsorption onto functionalize pumice stone.

    PubMed

    Asgari, Ghorban; Roshani, Babak; Ghanizadeh, Ghader

    2012-05-30

    In this research work, pumice that is functionalized by the cationic surfactant, hexadecyltrimethyl ammonium (HDTMA), is used as an adsorbent for the removal of fluoride from drinking water. This work was carried out in two parts. The effects of HDTMA loading, pH (3-10), reaction time (5-60 min) and the adsorbent dosage (0.15-2.5 g L(-1)) were investigated on the removal of fluoride as a target contaminate from water through the design of different experimental sets in the first part. The results from this first part revealed that surfactant-modified pumice (SMP) exhibited the best performance at dose 0.5 g L(-1), pH 6, and it adsorbs over 96% of fluoride from a solution containing 10 mg L(-1) fluoride after 30 min of mixing time. The four linear forms of the Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms model were applied to determine the best fit of equilibrium expressions. Apart from the regression coefficient (R(2)), four error functions were used to validate the isotherm and kinetics data. The experimental adsorption isotherm complies with Langmuir equation model type 1. The maximum amount of adsorption (Q(max)) was 41 mg g(-1). The kinetic studies indicated that the adsorption of fluoride best fitted with the pseudo-second-order kinetic type 1. Thermodynamic parameters evaluation of fluoride adsorption on SMP showed that the adsorption process under the selected conditions was spontaneous and endothermic. The suitability of SMP in defluoridation at field condition was investigated with natural groundwater samples collected from a nearby fluoride endemic area in the second part of this study. Based on this study's results, SMP was shown to be an affordable and a promising option for the removal of fluoride in drinking water.

  19. Ni (II) adsorption onto Chrysanthemum indicum: Influencing factors, isotherms, kinetics, and thermodynamics.

    PubMed

    Vilvanathan, Sowmya; Shanthakumar, S

    2016-10-01

    The study explores the adsorption potential of Chrysanthemum indicum biomass for nickel ion removal from aqueous solution. C. indicum flowers in raw (CIF-I) and biochar (CIF-II) forms were used as adsorbents in this study. Batch experiments were conducted to ascertain the optimum conditions of solution pH, adsorbent dosage, contact time, and temperature for varying initial Ni(II) ion concentrations. Surface area, surface morphology, and functionality of the adsorbents were characterized by Brunauer, Emmett, and Teller (BET) surface analysis, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR). Adsorption kinetics were modeled using pseudo-first order, pseudo-second order, Elovich, intraparticle diffusion, Bangham's, and Boyd's plot. The equilibrium data were modeled using Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R) isotherm models. Experimental data provided the best fit to pseudo-second-order kinetic model and Langmuir isotherm model for the adsorption of Ni(II) ion on both CIF-I and CIF-II with maximum adsorption capacities of 23.97 and 44.02 mg g(-1), respectively. Thermodynamic analysis of the data proved the process to be spontaneous and endothermic in nature. Desorption studies were conducted to evaluate the possibility of reusing the adsorbents. Findings of the present study provide substantial evidence for the use of C. indicum flower as an eco-friendly and potential adsorbent for the removal of Ni(II) ions from aqueous solution. PMID:27185382

  20. Multiscale analysis of nitrogen adsorption and desorption isotherms in soils developed over sandstone and basic parent materials with contrasting texture

    NASA Astrophysics Data System (ADS)

    Paz-Ferreiro, Jorge; Marinho, Mara de A.; de Abreu, Cleide A.

    2014-05-01

    Mono- and multifractal analysis of soil nitrogen adsorption isotherms (NAI) have been proven to be useful, allowing a better characterization of soil surface properties and soil porous system. Multiscale analysis of nitrogen desorption isotherms (NDI), which was less frequently performed, can also provide very valuable information. The multifractal theory was used to analyse both soil adsorption and desorption isotherms from soils developed over contrasting parent material and with different texture. We sampled 32 soil horizons from 6 soil profiles in neighbouring sites from São Paulo State, Brazil. Three of the profiles, developed over sandstone, were sandy loam or loamy, whereas the other three profiles, developed over weathered sediments or basic parent material, were clayey textured. Soil specific surface area (SSA) varied, from about 3.0 to 46 m2 g-1. Surface parameters showed a strong correlation with clay content, but they were not correlated with cation exchange capacity (CEC). The scaling properties of both nitrogen adsorption and desorption isotherms from all the studied soil horizons could be fitted reasonably well with multifractal models. Multifractal parameters from NAIs and NDIs showed great differences. The singularity spectra, f(α) of the desorption isotherms had an asymmetrically long left part and its asymmetry was in general higher compared with adsorption isotherms. Moreover, adsorption isotherms behaved like more clustered measures, showing lower entropy dimension, D1, smaller correlation dimension, D2, and higher heterogeneity than desorption isotherms. Differences in multifractal behaviour of NAIs and NDIs had been proven to be mainly related to the characteristics of the hysteretic loop measured at high relative pressures. Several multifractal parameters extracted from NAIs and NDIs also distinguished between sandy-loam and loam soils and clayey soils. Multifractal parameters calculated from NAIs and NDIs provide new insight to assess

  1. The Effect of Pore Connectivity on Water Adsorption Isotherms in Non-activated Graphitic Nanopores

    SciTech Connect

    StrioloDr., A; Gubbins, Dr. K. E.; Chialvo, Ariel A; Cummings, Peter T

    2005-01-01

    The adsorption of water in graphitic carbons is usually simulated via a weighted average of the adsorption isotherms simulated in carbon-slit pore of different widths. By following this procedure, details about pore morphology and pore connectivity may be overlooked. Towards a better match between virtual and real experiments, we present simulated adsorption isotherms for SPC/E model water in porous carbons composed by interconnected carbon-slit pores. The pores are separated from each other by one graphene layer. Imperfections (lack of carbon atoms) in the graphene layers result in interconnections between pores. The grand canonical Monte Carlo algorithm is used here to simulate water adsorption. Our results show that while the qualitative features obtained in the simulation of independent slit-shaped pores are reproduced when interconnected pores are considered, the adsorption isotherms rise more gradually and the adsorption/desorption hysteresis loops are narrower in the latter case.

  2. Ciprofloxacin adsorption on graphene and granular activated carbon: kinetics, isotherms, and effects of solution chemistry.

    PubMed

    Zhu, Xuan; Tsang, Daniel C W; Chen, Feng; Li, Shiyu; Yang, Xin

    2015-01-01

    Ciprofloxacin (CIP) is a commonly used antibiotic and widely detected in wastewaters and farmlands nowadays. This study evaluated the efficacy of next-generation adsorbent (graphene) and conventional adsorbent (granular activated carbon, GAC) for CIP removal. Batch experiments and characterization tests were conducted to investigate the adsorption kinetics, equilibrium isotherms, thermodynamic properties, and the influences of solution chemistry (pH, ionic strength, natural organic matter (NOM), and water sources). Compared to GAC, graphene showed significantly faster adsorption and reached equilibrium within 3 min, confirming the rapid access of CIP into the macroporous network of high surface area of graphene as revealed by the Brunner-Emmet-Teller measurements analysis. The kinetics was better described by a pseudo-second-order model, suggesting the importance of the initial CIP concentration related to surface site availability of graphene. The adsorption isotherm on graphene followed Langmuir model with a maximum adsorption capacity of 323 mg/g, which was higher than other reported carbonaceous adsorbents. The CIP adsorption was thermodynamically favourable on graphene and primarily occurred through π - π interaction, according to the FTIR spectroscopy. While the adsorption capacity of graphene decreased with increasing solution pH due to the speciation change of CIP, the adverse effects of ionic strength (0.01-0.5 mol L(-1)), presence of NOM (5 mg L⁻¹), and different water sources (river water or drinking water) were less significant on graphene than GAC. These results indicated that graphene can serve as an alternative adsorbent for CIP removal in commonly encountered field conditions, if proper separation and recovery is available in place. PMID:26050736

  3. Predicting the adsorption capacity and isotherm curvature of organic compounds onto activated carbons in natural waters.

    PubMed

    Hung, H W; Lin, T F

    2006-03-01

    A simple approach to predict the adsorption capacity and isotherm curvature of organic compounds onto activated carbon in natural water was investigated. A combination of the well-known equivalent background compound (EBC), and the simplified competitive adsorption model (SCAM) was employed to delineate the equilibrium capacity. This SCAM-EBC approach may reduce the numerical and experimental effort to obtain the parameters required to predict the adsorption capacity for a specific adsorption system. Several sets of experimental data, including weakly adsorbing (MTBE), strongly adsorbing compounds (TCP, atrazine, and chloroform), and two taste and odor causing compounds (MIB and geosmin) onto different activated carbons in three natural waters and a synthetic groundwater, were tested to verify the SCAM-EBC approach. Based on the approach, a parameter, called relative adsorptivity, describing the adsorption preference of the adsorbent between EBC and the target compound was employed to simulate the isotherm curvature in natural water. The relative adsorptivity of the SCAM-EBC approach is constant and can be directly obtained from the SCAM-EBC parameters in a specific adsorption system. The potential and extent of isotherm curvature can be simulated by only changing the parameter of relative adsorptivity. The marked isotherm curvature was found while the relative adsorptivity is larger than 2.0 to 4.0 for all the systems tested.

  4. Surface area and pore size characteristics of nanoporous gold subjected to thermal, mechanical, or surface modification studied using gas adsorption isotherms, cyclic voltammetry, thermogravimetric analysis, and scanning electron microscopy

    PubMed Central

    Tan, Yih Horng; Davis, Jason A.; Fujikawa, Kohki; Ganesh, N. Vijaya; Demchenko, Alexei V.

    2012-01-01

    Nitrogen adsorption/desorption isotherms are used to investigate the Brunauer, Emmett, and Teller (BET) surface area and Barrett-Joyner-Halenda (BJH) pore size distribution of physically modified, thermally annealed, and octadecanethiol functionalized np-Au monoliths. We present the full adsorption-desorption isotherms for N2 gas on np-Au, and observe type IV isotherms and type H1 hysteresis loops. The evolution of the np-Au under various thermal annealing treatments was examined using scanning electron microscopy (SEM). The images of both the exterior and interior of the thermally annealed np-Au show that the porosity of all free standing np-Au structures decreases as the heat treatment temperature increases. The modification of the np-Au surface with a self-assembled monolayer (SAM) of C18-SH (coverage of 2.94 × 1014 molecules cm−2 based from the decomposition of the C18-SH using thermogravimetric analysis (TGA)), was found to reduce the strength of the interaction of nitrogen gas with the np-Au surface, as reflected by a decrease in the ‘C’ parameter of the BET equation. From cyclic voltammetry studies, we found that the surface area of the np-Au monoliths annealed at elevated temperatures followed the same trend with annealing temperature as found in the BET surface area study and SEM morphology characterization. The study highlights the ability to control free-standing nanoporous gold monoliths with high surface area, and well-defined, tunable pore morphology. PMID:22822294

  5. Grand canonical Monte Carlo simulation of the adsorption isotherms of water molecules on model soot particles

    NASA Astrophysics Data System (ADS)

    Moulin, F.; Picaud, S.; Hoang, P. N. M.; Jedlovszky, P.

    2007-10-01

    The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. The soot particles are modeled by graphite-type layers arranged in an onionlike structure that contains randomly distributed hydrophilic sites, such as OH and COOH groups. The calculated water adsorption isotherm at 298K exhibits different characteristic shapes depending both on the type and the location of the hydrophilic sites and also on the size of the pores inside the soot particle. The different shapes of the adsorption isotherms result from different ways of water aggregation in or/and around the soot particle. The present results show the very weak influence of the OH sites on the water adsorption process when compared to the COOH sites. The results of these simulations can help in interpreting the experimental isotherms of water adsorbed on aircraft soot.

  6. A Sixth-Form Teaching Unit on the Langmuir Adsorption Isotherm

    ERIC Educational Resources Information Center

    Walkley, G. H.

    1973-01-01

    Presents a teaching unit on the Langmuir absorption isotherm suitable for advanced secondary school chemistry classes. Describes the experimental investigation of the isothermal adsorption of sulfur dioxide on charcoal, and discusses the derivation of the Langmuir equation and some applications. (JR)

  7. Adsorption of methylene blue onto poly(cyclotriphosphazene-co-4,4'-sulfonyldiphenol) nanotubes: kinetics, isotherm and thermodynamics analysis.

    PubMed

    Chen, Zhonghui; Zhang, Jianan; Fu, Jianwei; Wang, Minghuan; Wang, Xuzhe; Han, Runping; Xu, Qun

    2014-05-30

    Poly(cyclotriphosphazene-co-4,4'-sulfonyldiphenol) (PZS) nanotubes, an excellent adsorbent, were successfully synthesized by an in situ template method and used for the removal of methylene blue (MB) from aqueous solution. The morphology and structures of as-synthesized PZS nanotubes were characterized by scanning electron microscopy, transmission electron microscope, Fourier transform infrared spectroscopy and N2 adsorption/desorption isotherms. The effects of temperature, concentration, pH and contact time on MB adsorption were studied. It was favorable for adsorption under the condition of basic and high temperature. The pseudo-first-order, pseudo-second-order and intraparticle diffusion models were used to fit adsorption data in the kinetic studies. And results showed that the adsorption kinetics were more accurately described by the pseudo-second-order model. The equilibrium isotherms were conducted using Freundlich and Langmuir models. It has been demonstrated that the better agreement was Langmuir isotherm with correlation coefficient of 0.9933, equilibrium absorption capacity of 69.16mg/g and the corresponding contact time of 15min. Thermodynamic analyses showed that MB adsorption onto the PZS nanotubes was endothermic and spontaneous and it was also a physisorption process.

  8. A thermodynamically consistent explicit competitive adsorption isotherm model based on second-order single component behaviour.

    PubMed

    Ilić, Milica; Flockerzi, Dietrich; Seidel-Morgenstern, Andreas

    2010-04-01

    A competitive adsorption isotherm model is derived for binary mixtures of components characterized by single component isotherms which are second-order truncations of higher order equilibrium models suggested by multi-layer theory and statistical thermodynamics. The competitive isotherms are determined using the ideal adsorbed solution (IAS) theory which, in case of complex single component isotherms, does not generate explicit expressions to calculated equilibrium loadings and causes time consuming iterations in simulations of adsorption processes. The explicit model derived in this work is based on an analysis of the roots of a cubic polynomial resulting from the set of IAS equations. The suggested thermodynamically consistent and widely applicable competitive isotherm model can be recommended as a flexible tool for efficient simulations of fixed-bed adsorber dynamics.

  9. Comparative adsorption isotherms and modeling of methylene blue onto activated carbons

    NASA Astrophysics Data System (ADS)

    Belhachemi, Meriem; Addoun, Fatima

    2011-12-01

    The adsorption of methylene blue (MB) on activated carbons prepared from date stones with different degree of activation has been investigated. Equilibrium adsorption data of MB was carried out at 298 K. Four isotherm models (Freundlich, Langmuir, Redlich-Peterson and Sips) were tested for modeling the adsorption isotherms by nonlinear method. The three-parameter equations (Redlich-Peterson and Sips) showed more applicability than the two-parameter equations (Freundlich and Langmuir), which can be explained by the fact that these have three adjustable parameters. The best fit was achieved with the Redlich-Peterson equation according to the high value of correlation coefficient. All the samples were capable of retaining the MB, with the best result being reached by the sample with higher burn-off. Date stones activated carbon showed high adsorption capacity of 460 mg/g, calculated from the Sips isotherm model.

  10. Characterization of nitrogen adsorption isotherms of thermally-treated organoclays using multifractal analysis

    NASA Astrophysics Data System (ADS)

    Lado, Marcos; Borisover, Mikhail; Paz-Gonzalez, Antonio

    2013-04-01

    Nitrogen adsorption isotherms of soils have been reported to exhibit multifractal behavior. In the present work, multifractal analysis is used to characterize changes in N2 adsorption isotherms of organoclays prepared with different cations and exposed to various thermal treatments. Wyoming bentonite was exchanged with benzyltrimethylammonium (BTMA-clay), tetraethylammonium (TEA-clay), and hexadecyltrimethylammonium exchanged at 41 and 90% of the cation exchange capacity of the clay (HDTMA41- and HDTMA90-clay). The resulting organoclays were exposed to temperatures ranging from 25 to 420°C during two hours, freeze-dried, and N2 adsorption isotherms were measured at 77°K. The obtained isotherms showed multifractal behavior, and parameters derived from Rényi and singularity spectra varied with changes in the organic cation and the treatment temperature. The type of cation was the dominant factor responsible for changes in spectra, and significant interactions were observed between type of cation and temperature for several parameters. Significant correlations were found between organic carbon content and multifractal parameters, indicating a relation between changes in N2 sorption sites and thermal transformations of the organic cations. Significant correlations were also found between some multifractal parameters and the heterogeneity exponent of a Freundlich model fitted to nitrobenzene isotherms measured in the organoclays, suggesting that multifractal analysis of N2 adsorption isotherms could be useful to analyze the heterogeneity of sorption sites when sorption determinations yield a limited amount of data.

  11. Isothermal Adsorption Measurement for the Development of High Performance Solid Sorption Cooling System

    NASA Astrophysics Data System (ADS)

    Saha, Bidyut Baran; Koyama, Shigeru; Alam, K. C. Amanul; Hamamoto, Yoshinori; Akisawa, Atsushi; Kashiwagi, Takao; Ng, Kim Choon; Chua, Hui Tong

    Interest in low-grade thermal heat powered solid sorption system using natural refrigerants has been increased. However, the drawbacks of these adsorption systems are their poor performance. The objective of this paper is to improve the performance of thermally powered adsorption cooling system by selecting new adsorbent-refrigerant pairs. Adsorption capacity of adsorbent-refrigerant pair depends on the thermophysical properties (pore size, pore volume and pore diameter) of adsorbent and isothermal characteristics of the adsorbent-refrigerant pair. In this paper, the thermophysical properties of three types of silica gels and three types of pitch based activated carbon fibers are determined from the nitrogen adsorption isotherms. The standard nitrogen gas adsorption/desorption measurements on various adsorbents at liquid nitrogen of temperature 77.4 K were performed. Surface area of each adsorbent was determined by the Brunauer, Emmett and Teller (BET) plot of nitrogen adsorption data. Pore size distribution was measured by the Horvath and Kawazoe (HK) method. Adsorption/desorption isotherm results showed that all three carbon fibers have no hysteresis and had better adsorption capacity in comparison with those of silica gels.

  12. Kinetic Interpretation of Water Vapor Adsorption-Desorption Behavior of a Desiccant Rotor Showing S-shaped Adsorption Isotherm

    NASA Astrophysics Data System (ADS)

    Okamoto, Kumiko; Oshima, Kazunori; Takewaki, Takahiko; Kodama, Akio

    Adsorption / desorption behavior of water vapor in a desiccant rotor containing an iron aluminophosphate type zeolite FAM-Z01 (Functional Adsorbent Material Zeolite 01) was experimentally investigated for humidity swing. This rotor exhibited an S-shaped adsorption isotherm with its temperature dependence. Humidity swing, using a small piece of the rotor, could be usefully applied to interpret adsorption / desorption mechanisms by observing their rates. The most significant finding was that the adsorption / desorption rates in humidity swing could be described by the amount of adsorption, temperature and amplitude of the humidity swing, not by cycle time. Also, using the liner driving force (LDF) model, the overall mass transfer coefficient changed with the elapse of time or with the amount of adsorbed water. This implied that the LDF model, considering constant value of the overall mass transfer coefficient, was probably unable to explain the water adsorption / desorption behavior of FAM-Z01 desiccant rotor.

  13. A New Approach in Regression Analysis for Modeling Adsorption Isotherms

    PubMed Central

    Onjia, Antonije E.

    2014-01-01

    Numerous regression approaches to isotherm parameters estimation appear in the literature. The real insight into the proper modeling pattern can be achieved only by testing methods on a very big number of cases. Experimentally, it cannot be done in a reasonable time, so the Monte Carlo simulation method was applied. The objective of this paper is to introduce and compare numerical approaches that involve different levels of knowledge about the noise structure of the analytical method used for initial and equilibrium concentration determination. Six levels of homoscedastic noise and five types of heteroscedastic noise precision models were considered. Performance of the methods was statistically evaluated based on median percentage error and mean absolute relative error in parameter estimates. The present study showed a clear distinction between two cases. When equilibrium experiments are performed only once, for the homoscedastic case, the winning error function is ordinary least squares, while for the case of heteroscedastic noise the use of orthogonal distance regression or Margart's percent standard deviation is suggested. It was found that in case when experiments are repeated three times the simple method of weighted least squares performed as well as more complicated orthogonal distance regression method. PMID:24672394

  14. Adsorption on molecularly imprinted polymers of structural analogues of a template. Single-component adsorption isotherm data

    SciTech Connect

    Kim, Hyunjung; Guiochon, Georges A

    2005-10-01

    The equilibrium adsorption isotherms on two otherwise identical polymers, one imprinted with Fmoc-L-tryptophan (Fmoc-L-Trp) (MIP), the other nonimprinted (NIP), of compounds that are structural analogues of the template were acquired by frontal analysis (FA) in an acetonitrile/acetic acid (99/1 v/v) mobile phase, over a wide concentration range (from 0.005 to 50 mM). These analogues were Fmoc-L-tyrosine, Fmoc-L-serine, Fmoc-L-phenyalanine, Fmoc-glycine (Fmoc-Gly), Fmoc-L-tryptophan pentafluorophenyl ester (Fmoc-L-Trp(OPfp)), and their antipodes. These substrates have different numbers of functional groups able to interact with the 4-vinylpyridine groups of the polymer. For a given number of the functional groups, these substrates have different hydrophobicities of their side groups (as indicated by their partition coefficients (log P{sub ow}) in the octanol-water system (e.g., from 4.74 for Fmoc-Trp to 2.53 for Fmoc-Gly)). Statistical results from the fitting of the FA data to Langmuirian isotherm models, the calculation of the affinity energy distribution, and the comparison of calculated and experimental band profiles show that all these sets of FA data are best accounted for by a tri-Langmuir isotherm model, except for the data of Fmoc-L-Trp(OPfp) that are best modeled by a simple Langmuir isotherm. So, all compounds but Fmoc-L-Trp(OPfp) find three different types of adsorption sites on both the MIP and the NIP. The properties of these different types of sites were studied systematically. The results show that the affinity of the structural analogues for the NIP is controlled mostly by the number of the functional groups on the substrates and somewhat by the hydrophobicity of their side groups. These two factors control also the MIP affinity toward the enantiomers of the structural analogues that have a stereochemistry different from that of the template. In contrast, the affinity of the highest affinity sites of the MIP toward the enantiomers of these

  15. Evaluation of gaseous fluorocarbon adsorption isotherms on porous adsorbents under high pressure

    SciTech Connect

    Kaliappan, S.; Furuya, E.G.; Noll, K.E.; Chang, H.T.; Wang, H.C.

    1996-11-01

    In this study data have been collected to aid in the design of a control system that will remove fluorocarbons by adsorbing onto porous adsorbents. A bench scale experimental adsorption system had been designed using high accuracy MKS pressure transducers of 10,000 torr (two nos.) and a 100 torr connected to digital readout units. Tetrafluoromethane (CF{sub 4}) one of the fluorinated carbon family has been selected to evaluate the adsorption characteristics on porous adsorbents. The CF{sub 4} was charged to a sample reservoir in the test system at 200 psig pressure and at 22 C was allowed into an adsorption chamber at small increment of pressure rise. The pressure drop, using a Valydine PS 309 differential pressure gauge from the sample reservoir and the pressure buildup in the adsorption chamber were measured and the amount of CF{sub 4} adsorbed onto the adsorbents was calculated using ideal gas law. Various adsorbents, molecular sieve 13X, Silicagel (14 x 20), Beads Activated Carbon, Granular Activated Carbons PCB 6 x 16, BPL 4 x 10, F300, and F400 had been studied. It has been found that GAC-PCB 6 x 16 has the highest adsorbing capacity of 0.51 gm/gm at the conditions established. GAC-F300 had the second highest adsorbing capacity of 0.413 gm/gm, among all the adsorbents tested. The isotherms were analyzed using several equations employing both two parameters and three parameters. The relationship between the constants and physical properties of adsorbent solids and adsorbate molecules is discussed. The result of this study will be utilized to design a pressure swing fluorocarbon adsorption system that can be economically (using recycle of the collected fluorocarbons) applied to fluorocarbon removal in the electronic industry.

  16. Adsorption of arsenite and arsenate onto ferrihydrite under competitive conditions : kinetics, isotherm, and pH effect

    NASA Astrophysics Data System (ADS)

    Qi, P.; Pichler, T.

    2014-12-01

    Competitive adsorption of As(III) and As(V) onto ferrihydrite was investigated in both single and bi-component systems using batch experiments. The adsorption of As(III) was inhibited by the presence of As(V) over the whole pH range when compared to As(III) only conditions. As(V) was adsorbed to a similar extent with As(III) at low pH under competitive conditions. Isotherm studies also showed that As(V) significantly decreased the adsorption of As(III) at pH 5, while the presence of As(III) had a small effect on As(V) adsorption. The Freundlich isotherm equation was successfully fitted to both single and bi-component adsorption scenarios of As(III) and As(V). At the same time intervals in the first 2 h under competitive conditions, kinetics studies suggested that the amount of As(III) adsorbed in the presence of As(V) was reduced compared to the single component system at low pH. The effect of As(III) on the adsorption rate of As(V) was negligible. A pseudo-second-order model could be fitted perfectly to each species under both single and competitive conditions. The spectra of ferrihydrite with adsorbed As(III), As(V) or both As species have a similar shape by ATR-FTIR, indicating that competition may be at play.

  17. Adsorption kinetics and isotherm of anionic dyes onto organo-bentonite from single and multisolute systems.

    PubMed

    Shen, Dazhong; Fan, Jianxin; Zhou, Weizhi; Gao, Baoyu; Yue, Qinyan; Kang, Qi

    2009-12-15

    The performances of polydiallydimethylammonium modified bentonite (PDADMA-bentonite) as an adsorbent to remove anionic dyes, namely Acid Scarlet GR (AS-GR), Acid Turquoise Blue 2G (ATB-2G) and Indigo Carmine (IC), were investigated in single, binary and ternary dye systems. In adsorption from single dye solutions with initial concentration of 100 micromol/L, the dosage of PDADMA-bentonite needed to remove 95% dye was 0.42, 0.68 and 0.75 g/L for AS-GR, ATB-2G and IC, respectively. The adsorption isotherms of the three dyes obeyed the Langmuir isotherm model with the equilibrium constants of 0.372, 0.629 and 4.31 L/micromol, the saturation adsorption amount of 176.3, 149.2 and 228.7 micromol/g for ATB-2G, IC and AS-GR, respectively. In adsorption from mixed dye solutions, the isotherm of each individual dye followed an expanded Langmuir isotherm model and the relationship between the total amount of dyes adsorbed and the total equilibrium dye concentration was interpreted well by Langmuir isotherm model. In the region of insufficient dosage of PDADMA-bentonite, the dye with a larger affinity was preferentially removed by adsorption. Desorption was observed in the kinetic curve of the dye with lower affinity on PDADMA-bentonite surface by the competitive adsorption. The kinetics in single dye solution and the total adsorption of dyes in binary and ternary dye systems nicely followed pseudo-second-order kinetic model.

  18. Design, construction, and calibration of an isothermal titration calorimeter and its application in the study of the adsorption of phenolic compounds

    NASA Astrophysics Data System (ADS)

    Moreno-Piraján, Juan Carlos; Giraldo, Liliana

    2012-01-01

    An isothermal calorimetric titration was designed and built, and some of the results obtained are presented here. For this purpose, a Calvet heat-conducting microcalorimeter was developed and connected to a titration unit built for this experiment to record titration thermograms. The microcalorimeter was electrically calibrated to establish its sensitivity and reproducibility, obtaining K = 13.56 ± 0.21 W V-1. Additionally, the equipment was tested using the heat of neutralisation for the tris-hydroxymethyl-aminomethane-HCl (THAM-HCl) system, obtaining ΔH = -30.92 ± 0.03 kJ mol-1. The unit was assembled to obtain titration heats and the corresponding thermodynamic variables (ΔH, ΔG, ΔS, and Ke) with a system of phenolic derivatives-activated carbon (synthesised from potato peel).

  19. Design, construction, and calibration of an isothermal titration calorimeter and its application in the study of the adsorption of phenolic compounds.

    PubMed

    Moreno-Piraján, Juan Carlos; Giraldo, Liliana

    2012-01-01

    An isothermal calorimetric titration was designed and built, and some of the results obtained are presented here. For this purpose, a Calvet heat-conducting microcalorimeter was developed and connected to a titration unit built for this experiment to record titration thermograms. The microcalorimeter was electrically calibrated to establish its sensitivity and reproducibility, obtaining K = 13.56 ± 0.21 W V(-1). Additionally, the equipment was tested using the heat of neutralisation for the tris-hydroxymethyl-aminomethane-HCl (THAM-HCl) system, obtaining ΔH = -30.92 ± 0.03 kJ mol(-1). The unit was assembled to obtain titration heats and the corresponding thermodynamic variables (ΔH, ΔG, ΔS, and K(e)) with a system of phenolic derivatives-activated carbon (synthesised from potato peel).

  20. Application of isothermal titration calorimetry for characterizing thermodynamic parameters of biomolecular interactions: peptide self-assembly and protein adsorption case studies.

    PubMed

    Kabiri, Maryam; Unsworth, Larry D

    2014-10-13

    The complex nature of macromolecular interactions usually makes it very hard to identify the molecular-level mechanisms that ultimately dictate the result of these interactions. This is especially evident in the case of biological systems, where the complex interaction of molecules in various situations may be responsible for driving biomolecular interactions themselves but also has a broader effect at the cell and/or tissue level. This review will endeavor to further the understanding of biomolecular interactions utilizing the isothermal titration calorimetry (ITC) technique for thermodynamic characterization of two extremely important biomaterial systems, viz., peptide self-assembly and nonfouling polymer-modified surfaces. The advantages and shortcomings of this technique will be presented along with a thorough review of the recent application of ITC to these two areas. Furthermore, the controversies associated with the enthalpy-entropy compensation effect as well as thermodynamic equilibrium state for such interactions will be discussed.

  1. Artificial neural network (ANN) method for modeling of sunset yellow dye adsorption using zinc oxide nanorods loaded on activated carbon: Kinetic and isotherm study

    NASA Astrophysics Data System (ADS)

    Maghsoudi, M.; Ghaedi, M.; Zinali, A.; Ghaedi, A. M.; Habibi, M. H.

    2015-01-01

    In this research, ZnO nanoparticle loaded on activated carbon (ZnO-NPs-AC) was synthesized simply by a low cost and nontoxic procedure. The characterization and identification have been completed by different techniques such as SEM and XRD analysis. A three layer artificial neural network (ANN) model is applicable for accurate prediction of dye removal percentage from aqueous solution by ZnO-NRs-AC following conduction of 270 experimental data. The network was trained using the obtained experimental data at optimum pH with different ZnO-NRs-AC amount (0.005-0.015 g) and 5-40 mg/L of sunset yellow dye over contact time of 0.5-30 min. The ANN model was applied for prediction of the removal percentage of present systems with Levenberg-Marquardt algorithm (LMA), a linear transfer function (purelin) at output layer and a tangent sigmoid transfer function (tansig) in the hidden layer with 6 neurons. The minimum mean squared error (MSE) of 0.0008 and coefficient of determination (R2) of 0.998 were found for prediction and modeling of SY removal. The influence of parameters including adsorbent amount, initial dye concentration, pH and contact time on sunset yellow (SY) removal percentage were investigated and optimal experimental conditions were ascertained. Optimal conditions were set as follows: pH, 2.0; 10 min contact time; an adsorbent dose of 0.015 g. Equilibrium data fitted truly with the Langmuir model with maximum adsorption capacity of 142.85 mg/g for 0.005 g adsorbent. The adsorption of sunset yellow followed the pseudo-second-order rate equation.

  2. Kinetics and isotherm analysis of Tropaeoline 000 adsorption onto unsaturated polyester resin (UPR): a non-carbon adsorbent.

    PubMed

    Jain, Rajeev; Sharma, Pooja; Sikarwar, Shalini

    2013-03-01

    The presence of dyes in water is undesirable due to the toxicological impact of their entrance into the food chain. Owing to the recalcitrant nature of dyes to biological oxidation, a tertiary treatment like adsorption is required. In the present study, unsaturated polyester resin (UPR) has been used as a sorbent in the treatment of dye-contaminated water. Different concentrations of Tropaeoline 000 containing water were treated with UPR. The preliminary investigations were carried out by batch adsorption to examine the effects of pH, adsorbate concentration, adsorbent dosage, contact time, and temperature. A plausible mechanism for the ongoing adsorption process and thermodynamic parameters have also been obtained from Langmuir and Freundlich adsorption isotherm models. Thermodynamic parameter showed that the sorption process of Tropaeoline 000 onto activated carbon (AC) and UPR were feasible, spontaneous, and endothermic under studied conditions. The estimated values for (ΔG) are -10.48 × 10(3) and -6.098 × 10(3) kJ mol(-1) over AC and UPR at 303 K (30 °C), indicating towards a spontaneous process. The adsorption process followed pseudo-first-order model. The mass transfer property of the sorption process was studied using Lagergren pseudo-first-order kinetic models. The values of % removal and k (ad) for dye systems were calculated at different temperatures (303-323 K). The mechanism of the adsorption process was determined from the intraparticle diffusion model. PMID:22689095

  3. Modeling and CFD prediction for diffusion and adsorption within room with various adsorption isotherms.

    PubMed

    Murakami, S; Kato, S; Ito, K; Zhu, Q

    2003-01-01

    This paper presents physical models that are used for analyzing numerically the transportation of volatile organic compounds (VOCs) from building materials in a room. The models are based on fundamental physicochemical principles of their diffusion and adsorption/desorption (hereafter simply sorption) both in building materials and in room air. The performance of the proposed physical models is examined numerically in a test room with a technique supported by computational fluid dynamics (CFD). Two building materials are used in this study. One is a VOC emitting material for which the emission rate is mainly controlled by the internal diffusion of the material. The other is an adsorptive material that has no VOC source. It affects the room air concentration of VOCs with its sorption process. The floor is covered with an emission material made of polypropylene styrene-butadiene rubber (SBR). An adsorbent material made of coal-based activated carbon is spread over the sidewalls. The results of numerical prediction show that the physical models and their numerical simulations explain well the mechanism of the transportation of VOCs in a room.

  4. Water adsorption isotherms on porous onionlike carbonaceous particles. Simulations with the grand canonical Monte Carlo method.

    PubMed

    Hantal, György; Picaud, Sylvain; Hoang, Paul N M; Voloshin, Vladimir P; Medvedev, Nikolai N; Jedlovszky, Pál

    2010-10-14

    The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. These soot models are constructed by first removing atoms from onion-fullerene structures in order to create randomly distributed pores inside the soot, and then performing molecular dynamics simulations, based on the reactive adaptive intermolecular reactive empirical bond order (AIREBO) description of the interaction between carbon atoms, to optimize the resulting structures. The obtained results clearly show that the main driving force of water adsorption on soot is the possibility of the formation of new water-water hydrogen bonds with the already adsorbed water molecules. The shape of the calculated water adsorption isotherms at 298 K strongly depends on the possible confinement of the water molecules in pores of the carbonaceous structure. We found that there are two important factors influencing the adsorption ability of soot. The first of these factors, dominating at low pressures, is the ability of the soot of accommodating the first adsorbed water molecules at strongly hydrophilic sites. The second factor concerns the size and shape of the pores, which should be such that the hydrogen bonding network of the water molecules filling them should be optimal. This second factor determines the adsorption properties at higher pressures. PMID:20950025

  5. Water adsorption isotherms on porous onionlike carbonaceous particles. Simulations with the grand canonical Monte Carlo method

    NASA Astrophysics Data System (ADS)

    Hantal, György; Picaud, Sylvain; Hoang, Paul N. M.; Voloshin, Vladimir P.; Medvedev, Nikolai N.; Jedlovszky, Pál

    2010-10-01

    The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. These soot models are constructed by first removing atoms from onion-fullerene structures in order to create randomly distributed pores inside the soot, and then performing molecular dynamics simulations, based on the reactive adaptive intermolecular reactive empirical bond order (AIREBO) description of the interaction between carbon atoms, to optimize the resulting structures. The obtained results clearly show that the main driving force of water adsorption on soot is the possibility of the formation of new water-water hydrogen bonds with the already adsorbed water molecules. The shape of the calculated water adsorption isotherms at 298 K strongly depends on the possible confinement of the water molecules in pores of the carbonaceous structure. We found that there are two important factors influencing the adsorption ability of soot. The first of these factors, dominating at low pressures, is the ability of the soot of accommodating the first adsorbed water molecules at strongly hydrophilic sites. The second factor concerns the size and shape of the pores, which should be such that the hydrogen bonding network of the water molecules filling them should be optimal. This second factor determines the adsorption properties at higher pressures.

  6. Relation between Water Vapor Adsorption Isotherms and Dynamic Dehumidification Performances of Desiccant Rotor

    NASA Astrophysics Data System (ADS)

    Inoue, Koji; Matsuguma, Shingo; Jin, Wei-Li; Okano, Hiroshi; Teraoka, Yasutake; Hirose, Tsutomu

    Desiccant rotors with different water vapor adsorption properties were fabricated by the synthesis of silica gels inside the honeycomb matrices. Dynamic dehumidification performances of the rotors were measured under different conditions and they were discussed in relation to water vapor adsorption isotherms. At the reactivation air temperatures of 80 and 140 oC, the best dynamic performance was observed with the rotor on which the adsorbed amount of water vapor at lower relative humidity was highest. When the reactivation air temperature was 50 oC, on the other hand, the rotor of which the isotherm exhibited monotonic and nearly linear increase up to higher relative humidity was the most suitable. The normalized changes of absolute humidity and adsorbed amount were defined, and these phenomena were analyzed. When the dependences of both parameters against the relative humidity were similar, the rotor showed the best dehumidification performance.

  7. Kinetic and isotherm modeling of Cd (II) adsorption by L-cysteine functionalized multi-walled carbon nanotubes as adsorbent.

    PubMed

    Taghavi, Mahmoud; Zazouli, Mohammad Ali; Yousefi, Zabihollah; Akbari-adergani, Behrouz

    2015-11-01

    In this study, multi-walled carbon nanotubes were functionalized by L-cysteine to show the kinetic and isotherm modeling of Cd (II) ions onto L-cysteine functionalized multi-walled carbon nanotubes. The adsorption behavior of Cd (II) ion was studied by varying parameters including dose of L-MWCNTs, contact time, and cadmium concentration. Equilibrium adsorption isotherms and kinetics were also investigated based on Cd (II) adsorption tests. The results showed that an increase in contact time and adsorbent dosage resulted in increase of the adsorption rate. The optimum condition of the Cd (II) removal process was found at pH=7.0, 15 mg/L L-MWCNTs dosage, 6 mg/L cadmium concentration, and contact time of 60 min. The removal percent was equal to 89.56 at optimum condition. Langmuir and Freundlich models were employed to analyze the experimental data. The data showed well fitting with the Langmuir model (R2=0.994) with q max of 43.47 mg/g. Analyzing the kinetic data by the pseudo-first-order and pseudo-second-order equations revealed that the adsorption of cadmium using L-MWSNTs following the pseudo-second-order kinetic model with correlation coefficients (R2) equals to 0.998, 0.992, and 0.998 for 3, 6, and 9 mg/L Cd (II) concentrations, respectively. The experimental data fitted very well with the pseudo-second-order. Overall, treatment of polluted solution to Cd (II) by adsorption process using L-MWCNT can be considered as an effective technology.

  8. Adsorption on heterogeneous surfaces: site energy distribution functions from Fritz-Schlüender isotherms.

    PubMed

    Kumar, Kannuchamy Vasanth; Monteiro de Castro, Mateus Carvalho; Martinez-Escandell, Manuel; Molina-Sabio, Miguel; Rodriguez-Reinoso, Francisco

    2010-08-23

    Different site energy distribution functions based on the condensation approximation method are proposed for the liquid-phase or gas-phase adsorption equilibrium data following the Fritz-Schlüender isotherm. Energy distribution functions for the four limiting cases of the Fritz-Schlüender isotherm are also discussed. The proposed models are successfully applied to the experimental equilibrium data of nitrogen molecules at 77 K on a pitch-based activated carbon (PA) and a pitch-based activated carbon containing boron (PBA). An energy distribution function based on FS isotherm containing five parameters suggest a unimodal distribution of binding sites for carbon PA, the binding site energies being distributed as exponential or unimodal, depending on the pressure, in the case of carbon PBA. The advantages of the proposed models are discussed.

  9. Chromatography Models with Langmuir and Steric Mass Action Adsorption Isotherms are of Differential Index One

    NASA Astrophysics Data System (ADS)

    von Lieres, Eric

    2010-09-01

    Chromatography is commonly applied for the separation of bio-molecules in pharmaceutical industry, and chromatography models are increasingly applied for rational process analysis and optimization. A rapid equilibrium assumption is often applied for the adsorption equation, which results in a non-linear system of partial differential-algebraic equations (PDAEs). In this contribution a proof is given, that these PDAEs are of differential index one for the two most prominent isotherm models, Langmuir and steric mass action (SMA).

  10. Oxygen chemisorption on V/sub 2/O/sub 5/: isotherms and isobars of adsorption

    SciTech Connect

    Rey, L.; Gambaro, L.A.; Thomas, H.J.

    1984-06-01

    Experimental results of oxygen adsorption on V/sub 2/O/sub 5/ (isotherms and isobars) are reported. In its normal state V/sub 2/O/sub 5/ is a nonstoichiometric oxide that shows oxygen vacancies with the subsequent formation of V/sup 4 +/ ions. A model is developed for the interaction between oxygen (gaseous, adsorbed, and bulk) and the solid phase (V/sub 2/O/sub 5/). 12 references, 4 figures, 1 table.

  11. A regularization method for the reconstruction of adsorption isotherms in liquid chromatography

    NASA Astrophysics Data System (ADS)

    Zhang, Ye; Lin, Guang-Liang; Forssén, Patrik; Gulliksson, Mårten; Fornstedt, Torgny; Cheng, Xiao-Liang

    2016-10-01

    Determining competitive adsorption isotherms is an open problem in liquid chromatography. Since traditional experimental trial-and-error approaches are too complex and expensive, a modern technique of obtaining adsorption isotherms is to solve the inverse problem so that the simulated batch separation coincides with actual experimental results. This is a typical ill-posed problem. Moreover, in almost all cases the observed concentration at the outlet is the total response of all components, which makes the problem more difficult. In this work, we tackle the ill-posedness with a new regularization method, which is based on the fact that the adsorption isotherms do not depend on the injection profile. The proposed method transfers the original problem to an optimization problem with a time-dependent convection-diffusion equation constraint. Iterative algorithms for solving constraint optimization problems for both the equilibrium-dispersive and the transport-dispersive models are developed. The mass transfer resistance is also estimated by the proposed inverse method. A regularization parameter selection method and the convergence property of the proposed algorithm are discussed. Finally, numerical tests for both synthetic problems and real-world problems are given to show the efficiency and feasibility of the proposed regularization method.

  12. Gas desorption and adsorption isotherm studies of coals in the Powder River basin, Wyoming and adjacent basins in Wyoming and North Dakota

    USGS Publications Warehouse

    Stricker, Gary D.; Flores, Romeo M.; McGarry, Dwain E.; Stillwell, Dean P.; Hoppe, Daniel J.; Stillwell, Cathy R.; Ochs, Alan M.; Ellis, Margaret S.; Osvald, Karl S.; Taylor, Sharon L.; Thorvaldson, Marjorie C.; Trippi, Michael H.; Grose, Sherry D.; Crockett, Fred J.; Shariff, Asghar J.

    2006-01-01

    The U.S. Geological Survey (USGS), in cooperation with the State Office, Reservoir Management Group (RMG), of the Bureau of Land Management (BLM) in Casper (Wyoming), investigated the coalbed methane resources (CBM) in the Powder River Basin, Wyoming and Montana, from 1999 to the present. Beginning in late 1999, the study also included the Williston Basin in Montana and North and South Dakota and Green River Basin and Big Horn Basin in Wyoming. The rapid development of CBM (referred to as coalbed natural gas by the BLM) during the early 1990s, and the lack of sufficient data for the BLM to fully assess and manage the resource in the Powder River Basin, in particular, gave impetus to the cooperative program. An integral part of the joint USGS-BLM project was the participation of 25 gas operators that entered individually into confidential agreements with the USGS, and whose cooperation was essential to the study. The arrangements were for the gas operators to drill and core coal-bed reservoirs at their cost, and for the USGS and BLM personnel to then desorb, analyze, and interpret the coal data with joint funding by the two agencies. Upon completion of analyses by the USGS, the data were to be shared with both the BLM and the gas operator that supplied the core, and then to be released or published 1 yr after the report was submitted to the operator.

  13. The Republic of the Philippines coalbed methane assessment: based on seventeen high pressure methane adsorption isotherms

    USGS Publications Warehouse

    Flores, Romeo M.; Stricker, Gary D.; Papasin, Ramon F.; Pendon, Ronaldo R.; del Rosario, Rogelio A.; Malapitan, Ruel T.; Pastor, Michael S.; Altomea, Elmer A.; Cuaresma, Federico; Malapitan, Armando S.; Mortos, Benjamin R.; Tilos, Elizabeth N.

    2006-01-01

    Semirara coal led to the present study of determining the adsorption isotherms, or gas (CBM) holding or storage capacity, of coal beds of various ages from selected coal districts in the Philippines. Samples for the study were collected from the Batan Island, Catanduanes, Cagayan-Isabella, Cebu, Negros, Samar, Semirara, Cotabato, Surigao, and Malangas coalfield of the Zamboanga Sibuguey coal districts by five field geology teams from the GCRDD.

  14. Valorization of agricultural wastes as dye adsorbents: characterization and adsorption isotherms.

    PubMed

    Sepúlveda, Luisa A; Cuevas, Fernando A; Contreras, Elsa G

    2015-01-01

    The purpose of this work is to evaluate the valorization of agricultural waste, wheat straw (WS) and corn cob leaves (CCLs) as textile dye adsorbents. Physico-chemical and superficial characteristics of the agricultural wastes, together with the interactions with the CI Basic Violet 4 (BV4) dye, were investigated by means of the determination of the isotherm adsorption at different temperatures. The morphological characterization showed that the solid surface is coarse with a low pore level. However, through Fourier transformed infrared analysis, the presence of carboxylic and hydroxylic acid groups and hydrophobic methyl groups was detected. The concentration of acid groups is determined by the Boehm method and was found to be 1.00 and 0.89 meq/g for WS and CCLs, respectively. The point zero charge for each adsorbent was 5.76 and 4.08. Adsorption experimental data presented a better-fit Langmuir model, indicating that adsorption occurred in a monolayer with preferential interaction. The maximum adsorption capacity was determined to be 70.0-89.0 and 47.0-68.0 mg/g for CCLs and WS, respectively. The thermodynamic analysis of the Langmuir parameter b showed that the adsorption of the BV4 dye is spontaneous and exothermic with adsorption energies of 14.43 and 5.58 KJ/mol for CCLs and WS, respectively.

  15. Valorization of agricultural wastes as dye adsorbents: characterization and adsorption isotherms.

    PubMed

    Sepúlveda, Luisa A; Cuevas, Fernando A; Contreras, Elsa G

    2015-01-01

    The purpose of this work is to evaluate the valorization of agricultural waste, wheat straw (WS) and corn cob leaves (CCLs) as textile dye adsorbents. Physico-chemical and superficial characteristics of the agricultural wastes, together with the interactions with the CI Basic Violet 4 (BV4) dye, were investigated by means of the determination of the isotherm adsorption at different temperatures. The morphological characterization showed that the solid surface is coarse with a low pore level. However, through Fourier transformed infrared analysis, the presence of carboxylic and hydroxylic acid groups and hydrophobic methyl groups was detected. The concentration of acid groups is determined by the Boehm method and was found to be 1.00 and 0.89 meq/g for WS and CCLs, respectively. The point zero charge for each adsorbent was 5.76 and 4.08. Adsorption experimental data presented a better-fit Langmuir model, indicating that adsorption occurred in a monolayer with preferential interaction. The maximum adsorption capacity was determined to be 70.0-89.0 and 47.0-68.0 mg/g for CCLs and WS, respectively. The thermodynamic analysis of the Langmuir parameter b showed that the adsorption of the BV4 dye is spontaneous and exothermic with adsorption energies of 14.43 and 5.58 KJ/mol for CCLs and WS, respectively. PMID:25655393

  16. Effect of cation type, alkyl chain length, adsorbate size on adsorption kinetics and isotherms of bromide ionic liquids from aqueous solutions onto microporous fabric and granulated activated carbons.

    PubMed

    Hassan, Safia; Duclaux, Laurent; Lévêque, Jean-Marc; Reinert, Laurence; Farooq, Amjad; Yasin, Tariq

    2014-11-01

    The adsorption from aqueous solution of imidazolium, pyrrolidinium and pyridinium based bromide ionic liquids (ILs) having different alkyl chain lengths was investigated on two types of microporous activated carbons: a fabric and a granulated one, well characterized in terms of surface chemistry by "Boehm" titrations and pH of point of zero charge measurements and of porosity by N2 adsorption at 77 K and CO2 adsorption at 273 K. The influence of cation type, alkyl chain length and adsorbate size on the adsorption properties was analyzed by studying kinetics and isotherms of eight different ILs using conductivity measurements. Equilibrium studies were carried out at different temperatures in the range [25-55 °C]. The incorporation of ILs on the AC porosity was studied by N2 adsorption-desorption measurements at 77 K. The experimental adsorption isotherms data showed a good correlation with the Langmuir model. Thermodynamic studies indicated that the adsorption of ILs onto activated carbons was an exothermic process, and that the removal efficiency increased with increase in alkyl chain length, due to the increase in hydrophobicity of long chain ILs cations determined with the evolution of the calculated octanol-water constant (Kow). The negative values of free energies indicated that adsorption of ILs with long chain lengths having hydrophobic cations was more spontaneous at the investigated temperatures.

  17. Water adsorption isotherms of carboxymethyl cellulose, guar, locust bean, tragacanth and xanthan gums.

    PubMed

    Torres, María D; Moreira, Ramón; Chenlo, Francisco; Vázquez, María J

    2012-06-20

    Water adsorption isotherms of carboxymethyl cellulose (CMC), guar gum (GG), locust bean gum (LBG), tragacanth gum (TG) and xanthan gum (XG) were determined at different temperatures (20, 35, 50, and 65°C) using a gravimetric method. Several saturated salt solutions were selected to obtain different water activities in the range from 0.09 to 0.91. Water adsorption isotherms of tested hydrocolloids were classified like type II isotherms. In all cases, equilibrium moisture content decreased with increasing temperature at each water activity value. Three-parameter Guggenheim-Anderson-de Boer (GAB) model was employed to fit the experimental data in the water activity range and statistical analysis indicated that this model gave satisfactory results. CMC and GG were the most and the least hygroscopic gums, respectively. Sorption heats decreased with increasing moisture content. Monolayer moisture content evaluated with GAB model was consistent with equilibrium conditions of maximum stability calculated from thermodynamic analysis of net integral entropy. Values of equilibrium relative humidity at 20°C are proposed to storage adequately the tested gums.

  18. Adsorption isotherms for hydrogen chloride (HCl) on ice surfaces between 190 and 220 K.

    PubMed

    Zimmermann, S; Kippenberger, M; Schuster, G; Crowley, J N

    2016-05-18

    The interaction of hydrogen chloride (HCl) with ice surfaces at temperatures between 190 and 220 K was investigated using a coated-wall flow-tube connected to a chemical ionization mass spectrometer. Equilibrium surface coverages of HCl were determined at gas phase concentrations as low as 2 × 10(9) molecules cm(-3) (∼4 × 10(-8) Torr at 200 K) to derive Langmuir adsorption isotherms. The data are described by a temperature independent partition coefficient: KLang = (3.7 ± 0.2) × 10(-11) cm(3) molecule(-1) with a saturation surface coverage Nmax = (2.0 ± 0.2) × 10(14) molecules cm(-2). The lack of a systematic dependence of KLang on temperature contrasts the behaviour of numerous trace gases which adsorb onto ice via hydrogen bonding and is most likely related to the ionization of HCl at the surface. The results are compared to previous laboratory studies, and the equilibrium partitioning of HCl to ice surfaces under conditions relevant to the atmosphere is evaluated. PMID:27142478

  19. Adsorption isotherms for hydrogen chloride (HCl) on ice surfaces between 190 and 220 K.

    PubMed

    Zimmermann, S; Kippenberger, M; Schuster, G; Crowley, J N

    2016-05-18

    The interaction of hydrogen chloride (HCl) with ice surfaces at temperatures between 190 and 220 K was investigated using a coated-wall flow-tube connected to a chemical ionization mass spectrometer. Equilibrium surface coverages of HCl were determined at gas phase concentrations as low as 2 × 10(9) molecules cm(-3) (∼4 × 10(-8) Torr at 200 K) to derive Langmuir adsorption isotherms. The data are described by a temperature independent partition coefficient: KLang = (3.7 ± 0.2) × 10(-11) cm(3) molecule(-1) with a saturation surface coverage Nmax = (2.0 ± 0.2) × 10(14) molecules cm(-2). The lack of a systematic dependence of KLang on temperature contrasts the behaviour of numerous trace gases which adsorb onto ice via hydrogen bonding and is most likely related to the ionization of HCl at the surface. The results are compared to previous laboratory studies, and the equilibrium partitioning of HCl to ice surfaces under conditions relevant to the atmosphere is evaluated.

  20. Investigation of simultaneous biosorption of copper(II) and chromium(VI) on dried Chlorella vulgaris from binary metal mixtures: Application of multicomponent adsorption isotherms

    SciTech Connect

    Aksu, Z.; Acikel, U.; Kutsal, T.

    1999-02-01

    Although the biosorption of single metal ions to various kinds of microorganisms has been extensively studied and the adsorption isotherms have been developed for only the single metal ion situation, very little attention has been given to the bioremoval and expression of adsorption isotherms of multimetal ions systems. In this study the simultaneous biosorption of copper(II) and chromium(VI) to Chlorella vulgaris from a binary metal mixture was studied and compared with the single metal ion situation in a batch stirred system. The effects of pH and single- and dual-metal ion concentrations on the equilibrium uptakes were investigated. In previous studies the optimum biosorption pH had been determined as 4.0 for copper(II) and as 2.0 for chromium(VI). Multimetal ion biosorption studies were performed at these two pH values. It was observed that the equilibrium uptakes of copper(II) or chromium(VI) ions were changed due to the biosorption pH and the presence of other metal ions. Adsorption isotherms were developed for both single- and dual-metal ions systems at these two pH values, and expressed by the mono- and multicomponent Langmuir and Freundlich adsorption models. Model parameters were estimated by nonlinear regression. It was seen that the adsorption equilibrium data fitted very well to the competitive Freundlich model in the concentration ranges studied.

  1. Modeling Nonlinear Adsorption to Carbon with a Single Chemical Parameter: A Lognormal Langmuir Isotherm.

    PubMed

    Davis, Craig Warren; Di Toro, Dominic M

    2015-07-01

    Predictive models for linear sorption of solutes onto various media, e.g., soil organic carbon, are well-established; however, methods for predicting parameters for nonlinear isotherm models, e.g., Freundlich and Langmuir models, are not. Predicting nonlinear partition coefficients is complicated by the number of model parameters to fit n isotherms (e.g., Freundlich (2n) or Polanyi-Manes (3n)). The purpose of this paper is to present a nonlinear adsorption model with only one chemically specific parameter. To accomplish this, several simplifications to a log-normal Langmuir (LNL) isotherm model with 3n parameters were explored. A single sorbate-specific binding constant, the median Langmuir binding constant, and two global sorbent parameters; the total site density and the standard deviation of the Langmuir binding constant were employed. This single-solute specific (ss-LNL) model (2 + n parameters) was demonstrated to fit adsorption data as well as the 2n parameter Freundlich model. The LNL isotherm model is fit to four data sets composed of various chemicals sorbed to graphite, charcoal, and activated carbon. The RMS errors for the 3-, 2-, and 1-chemical specific parameter models were 0.066, 0.068, 0.069, and 0.113, respectively. The median logarithmic parameter standard errors for the four models were 1.070, 0.4537, 0.382, and 0.201 respectively. Further, the single-parameter model was the only model for which there were no standard errors of estimated parameters greater than a factor of 3 (0.50 log units). The surprising result is that very little decrease in RMSE occurs when two of the three parameters, σκ and qmax, are sorbate independent. However, the large standard errors present in the other models are significantly reduced. This remarkable simplification yields the single sorbate-specific parameter (ss-LNL) model. PMID:26035092

  2. Modeling Nonlinear Adsorption to Carbon with a Single Chemical Parameter: A Lognormal Langmuir Isotherm.

    PubMed

    Davis, Craig Warren; Di Toro, Dominic M

    2015-07-01

    Predictive models for linear sorption of solutes onto various media, e.g., soil organic carbon, are well-established; however, methods for predicting parameters for nonlinear isotherm models, e.g., Freundlich and Langmuir models, are not. Predicting nonlinear partition coefficients is complicated by the number of model parameters to fit n isotherms (e.g., Freundlich (2n) or Polanyi-Manes (3n)). The purpose of this paper is to present a nonlinear adsorption model with only one chemically specific parameter. To accomplish this, several simplifications to a log-normal Langmuir (LNL) isotherm model with 3n parameters were explored. A single sorbate-specific binding constant, the median Langmuir binding constant, and two global sorbent parameters; the total site density and the standard deviation of the Langmuir binding constant were employed. This single-solute specific (ss-LNL) model (2 + n parameters) was demonstrated to fit adsorption data as well as the 2n parameter Freundlich model. The LNL isotherm model is fit to four data sets composed of various chemicals sorbed to graphite, charcoal, and activated carbon. The RMS errors for the 3-, 2-, and 1-chemical specific parameter models were 0.066, 0.068, 0.069, and 0.113, respectively. The median logarithmic parameter standard errors for the four models were 1.070, 0.4537, 0.382, and 0.201 respectively. Further, the single-parameter model was the only model for which there were no standard errors of estimated parameters greater than a factor of 3 (0.50 log units). The surprising result is that very little decrease in RMSE occurs when two of the three parameters, σκ and qmax, are sorbate independent. However, the large standard errors present in the other models are significantly reduced. This remarkable simplification yields the single sorbate-specific parameter (ss-LNL) model.

  3. A site energy distribution function from Toth isotherm for adsorption of gases on heterogeneous surfaces.

    PubMed

    Kumar, K Vasanth; de Castro, M Monteiro; Martinez-Escandell, M; Molina-Sabio, M; Rodriguez-Reinoso, F

    2011-04-01

    A site energy distribution function based on a condensation approximation method is proposed for gas-phase adsorption systems following the Toth isotherm. The proposed model is successfully applied to estimate the site energy distribution of three pitch-based activated carbons (PA, PFeA and PBA) developed in our laboratory and also for other common adsorbent materials for different gas molecules. According to the proposed model the site energy distribution curves of the activated carbons are found to be exponential for hydrogen at 77 K. The site energy distribution of some of the activated carbon fibers, ambersorb, Dowex optipore, 13X Zeolite for different adsorbate molecules represents a quasi-Gaussian curve with a widened left hand side, indicating that most sites have adsorption energies lower than a statistical mean value.

  4. Low-cost magnetic adsorbent for As(III) removal from water: adsorption kinetics and isotherms.

    PubMed

    Kango, Sarita; Kumar, Rajesh

    2016-01-01

    Magnetite nanoparticles as adsorbent for arsenic (As) were coated on sand particles. The coated sand was used for the removal of highly toxic element 'As(III)' from drinking water. Here, batch experiments were performed with the variation of solution pH, adsorbent dose, contact time and initial arsenic concentration. The adsorbent showed significant removal efficiency around 99.6 % for As(III). Analysis of adsorption kinetics revealed that the adsorbent follows pseudo-second-order kinetics model showing R (2) = 0.999, whereas for pseudo-first-order kinetics model, the value of R (2) was 0.978. In the case of adsorption equilibrium, the data is well fitted with Langmuir adsorption isotherm model (R (2) > 0.99), indicating monolayer adsorption of As(III) on the surface of adsorbent. The existence of commonly present ions in water influences the removal efficiency of As(III) minutely in the following order PO4 (3-) > HCO3 (-) > Cl(-) > SO4 (2-). The obtained adsorbent can be used to overcome the problem of water filtration in rural areas. Moreover, as the nano-magnetite is coated on the sand, it avoids the problem of extraction of nanoparticles from treated water and can easily be removed by a simple filtration process. PMID:26711813

  5. Low-cost magnetic adsorbent for As(III) removal from water: adsorption kinetics and isotherms.

    PubMed

    Kango, Sarita; Kumar, Rajesh

    2016-01-01

    Magnetite nanoparticles as adsorbent for arsenic (As) were coated on sand particles. The coated sand was used for the removal of highly toxic element 'As(III)' from drinking water. Here, batch experiments were performed with the variation of solution pH, adsorbent dose, contact time and initial arsenic concentration. The adsorbent showed significant removal efficiency around 99.6 % for As(III). Analysis of adsorption kinetics revealed that the adsorbent follows pseudo-second-order kinetics model showing R (2) = 0.999, whereas for pseudo-first-order kinetics model, the value of R (2) was 0.978. In the case of adsorption equilibrium, the data is well fitted with Langmuir adsorption isotherm model (R (2) > 0.99), indicating monolayer adsorption of As(III) on the surface of adsorbent. The existence of commonly present ions in water influences the removal efficiency of As(III) minutely in the following order PO4 (3-) > HCO3 (-) > Cl(-) > SO4 (2-). The obtained adsorbent can be used to overcome the problem of water filtration in rural areas. Moreover, as the nano-magnetite is coated on the sand, it avoids the problem of extraction of nanoparticles from treated water and can easily be removed by a simple filtration process.

  6. How soil organic matter composition controls hexachlorobenzene-soil-interactions: adsorption isotherms and quantum chemical modeling.

    PubMed

    Ahmed, Ashour A; Kühn, Oliver; Aziz, Saadullah G; Hilal, Rifaat H; Leinweber, Peter

    2014-04-01

    Hazardous persistent organic pollutants (POPs) interact in soil with the soil organic matter (SOM) but this interaction is insufficiently understood at the molecular level. We investigated the adsorption of hexachlorobenzene (HCB) on soil samples with systematically modified SOM. These samples included the original soil, the soil modified by adding a hot water extract (HWE) fraction (soil+3 HWE and soil+6 HWE), and the pyrolyzed soil. The SOM contents increased in the order pyrolyzed soiladsorption. The pyrolyzed soil adsorbed more HCB than the other samples at low initial concentrations, but at higher concentrations the HCB adsorption became weaker than in the samples with HWE addition. This adsorption combined with the differences in the chemical composition between the soil samples suggested that alkylated aromatic, phenol, and lignin monomer compounds contributed most to the HCB adsorption. To obtain a molecular level understanding, a test set has been developed on the basis of elemental analysis which comprises 32 representative soil constituents. The calculated binding energy for HCB with each representative system shows that HCB binds to SOM stronger than to soil minerals. For SOM, HCB binds to alkylated aromatic, phenols, lignin monomers, and hydrophobic aliphatic compounds stronger than to polar aliphatic compounds confirming the above adsorption isotherms. Moreover, quantitative structure-activity relationship (QSAR) of the binding energy with independent physical properties of the test set systems for the first time indicated that the polarizability, the partial charge on the carbon atoms, and the molar volume are the most important properties controlling HCB-SOM interactions.

  7. Description of Chemically and Thermally Treated Multi-Walled Carbon Nanotubes Using Sequential Decomposition of Adsorption Isotherms

    NASA Astrophysics Data System (ADS)

    Albesa, Alberto G.; Rafti, Matías; Vicente, José Luis

    2016-03-01

    The effect of wet acid oxidation by means of sulfuric/nitric acid mixtures, and high-temperature treatment of commercial arc-discharge synthesized multi-walled carbon nanotubes (MWCNTs) was studied. In order to analyze the adsorption capacities of differently treated MWCNTs, we employed a multistep method that considers separately different pressure ranges (zones) on the experimentally obtained isotherms. The method is based on simple gas isotherm measurements (N2, CO2, CH4, etc.). Low pressure ranges can be described using Dubinin’s model, while high pressure regimes can be fitted using different models such as BET multilayer and Freundlich equations. This analysis allows to elucidate how different substrate treatments (chemical and thermal) can affect the adsorbate-adsorbent interactions; moreover, theoretical description of adsorbate-adsorbate interactions can be improved if a combination of adsorption mechanisms are used instead of a unique model. The results hereby presented also show that, while MWCNTs are a promising material for storage applications, gas separation applications should carefully consider the effect of wide nanotube size distribution present on samples after activation procedures.

  8. Effect of 300 and 500 MPa pressure treatments on starch-water adsorption/desorption isotherms and hysteresis

    NASA Astrophysics Data System (ADS)

    Santos, Mauro D.; Cunha, Pedro; Queirós, Rui P.; Fidalgo, Liliana G.; Delgadillo, Ivonne; Saraiva, Jorge A.

    2014-10-01

    Pressure treatments of 300 and 500 MPa during 15 min were found to change starch-water sorption (adsorption and desorption) isotherms and the hysteresis effect, particularly the 500 MPa. This last treatment shifted the adsorption/desorption isotherms downward, compared with non-treated starch and starch treated at 300 MPa. The observed hysteresis effect decreased with the increase in pressure level in the whole aw range, indicating that adsorption and desorption isotherms became closer. Guggenheim-Anderson-De Boer and Brunauer-Emmett-Teller model parameters Cb, Cg, K and Mm also showed changes caused by pressure, the latter being lower in the pressure-processed samples, thus indicating possible changes on microbial and (bio)chemical stabilities of pressure-processed food products containing starch.

  9. A comparative examination of the adsorption mechanism of an anionic textile dye (RBY 3GL) onto the powdered activated carbon (PAC) using various the isotherm models and kinetics equations with linear and non-linear methods

    NASA Astrophysics Data System (ADS)

    Açıkyıldız, Metin; Gürses, Ahmet; Güneş, Kübra; Yalvaç, Duygu

    2015-11-01

    The present study was designed to compare the linear and non-linear methods used to check the compliance of the experimental data corresponding to the isotherm models (Langmuir, Freundlich, and Redlich-Peterson) and kinetics equations (pseudo-first order and pseudo-second order). In this context, adsorption experiments were carried out to remove an anionic dye, Remazol Brillant Yellow 3GL (RBY), from its aqueous solutions using a commercial activated carbon as a sorbent. The effects of contact time, initial RBY concentration, and temperature onto adsorbed amount were investigated. The amount of dye adsorbed increased with increased adsorption time and the adsorption equilibrium was attained after 240 min. The amount of dye adsorbed enhanced with increased temperature, suggesting that the adsorption process is endothermic. The experimental data was analyzed using the Langmuir, Freundlich, and Redlich-Peterson isotherm equations in order to predict adsorption isotherm. It was determined that the isotherm data were fitted to the Langmuir and Redlich-Peterson isotherms. The adsorption process was also found to follow a pseudo second-order kinetic model. According to the kinetic and isotherm data, it was found that the determination coefficients obtained from linear method were higher than those obtained from non-linear method.

  10. Study of adsorption of Neon on open Carbon nanohorns aggregates

    NASA Astrophysics Data System (ADS)

    Ziegler, Carl Andrew

    Adsorption isotherms can be used to determine surface area of a substrate and the heat released when adsorption occurs. Our measurements are done determining the equilibrium pressures corresponding to a given amount of gas adsorbed on a substrate at constant temperature. The adsorption studies were done on aggregates of open dahlia-like carbon nanohorns. The nanohorns were oxidized for 9 hours at 550 °C to open them up and render their interior space accessible for adsorption. Volumetric adsorption measurements of Ne were performed at twelve different temperatures between 19 K and 48 K. The isotherms showed two substeps. The first substep corresponds to adsorption on the high energy binding sites in the interior of the nanohorns, near the tip. The second substep corresponds to low energy binding sites both on the outside of the nanotubes and inside the nanotube away from the tip. The isosteric heat measurements obtained from the isotherm data also shows these two distinct substeps. The effective surface area of the open nanotubes was determined from the isotherms using the point-B method. The isosteric heat and surface area data for neon on open nanohorns were compared to two similar experiments of neon adsorbed on aggregates of closed nanohorns.

  11. Evaluation of lead(II) immobilization by a vermicompost using adsorption isotherms and IR spectroscopy.

    PubMed

    Carrasquero-Durán, Armando; Flores, Iraima

    2009-02-01

    The immobilization of lead ions by a vermicompost with calcite added was evaluated by adsorption isotherms and the results were explained on basis of the pH dependent surface charge and by IR spectroscopy. The results showed maximum adsorption values between 113.6 mg g(-1) (33 degrees C) and 123.5mg g(-1) (50 degrees C). The point of zero net charge (PZC) was 7.5+/-0.1, indicating the presence of a positive surface charge at the pH of batch experiments. The differences in the IR spectra at pH 3.8 and 7.0 in the region from 1800 to 1300 cm(-1), were interpreted on the basis of the carboxyl acid ionization, that reduced the band intensity around 1725 cm(-1), producing signals at 1550 cm(-1) and 1390 cm(-1) of carboxylate groups. Similar changes were detected at pH 3.8 when Pb2+ was present suggesting that the ion complexation takes place by a cationic exchange equilibrium, between the protons and Pb2+ ions.

  12. Adsorption isotherms and kinetics of activated carbons produced from coals of different ranks.

    PubMed

    Purevsuren, B; Lin, Chin-Jung; Davaajav, Y; Ariunaa, A; Batbileg, S; Avid, B; Jargalmaa, S; Huang, Yu; Liou, Sofia Ya-Hsuan

    2015-01-01

    Activated carbons (ACs) from six coals, ranging from low-rank lignite brown coal to high-rank stone coal, were utilized as adsorbents to remove basic methylene blue (MB) from an aqueous solution. The surface properties of the obtained ACs were characterized via thermal analysis, N2 isothermal sorption, scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and Boehm titration. As coal rank decreased, an increase in the heterogeneity of the pore structures and abundance of oxygen-containing functional groups increased MB coverage on its surface. The equilibrium data fitted well with the Langmuir model, and adsorption capacity of MB ranged from 51.8 to 344.8 mg g⁻¹. Good correlation coefficients were obtained using the intra-particle diffusion model, indicating that the adsorption of MB onto ACs is diffusion controlled. The values of the effective diffusion coefficient ranged from 0.61 × 10⁻¹⁰ to 7.1 × 10⁻¹⁰ m² s⁻¹, indicating that ACs from lower-rank coals have higher effective diffusivities. Among all the ACs obtained from selected coals, the AC from low-rank lignite brown coal was the most effective in removing MB from an aqueous solution. PMID:25909729

  13. Predicting CH4 adsorption capacity of microporous carbon using N2 isotherm and a new analytical model

    USGS Publications Warehouse

    Sun, Jielun; Chen, S.; Rostam-Abadi, M.; Rood, M.J.

    1998-01-01

    A new analytical pore size distribution (PSD) model was developed to predict CH4 adsorption (storage) capacity of microporous adsorbent carbon. The model is based on a 3-D adsorption isotherm equation, derived from statistical mechanical principles. Least squares error minimization is used to solve the PSD without any pre-assumed distribution function. In comparison with several well-accepted analytical methods from the literature, this 3-D model offers relatively realistic PSD description for select reference materials, including activated carbon fibers. N2 and CH4 adsorption data were correlated using the 3-D model for commercial carbons BPL and AX-21. Predicted CH4 adsorption isotherms, based on N2 adsorption at 77 K, were in reasonable agreement with the experimental CH4 isotherms. Modeling results indicate that not all the pores contribute the same percentage Vm/Vs for CH4 storage due to different adsorbed CH4 densities. Pores near 8-9 A?? shows higher Vm/Vs on the equivalent volume basis than does larger pores.

  14. Adsorption of emulsified oil from metalworking fluid on activated bleaching earth-chitosan-SDS composites: Optimization, kinetics, isotherms.

    PubMed

    Naowanat, Nitiya; Thouchprasitchai, Nutthavich; Pongstabodee, Sangobtip

    2016-03-15

    The adsorption of emulsified oil from metalworking fluid (MWF) on activated bleaching earth (BE)-chitosan-sodium dodecyl sulfate (SDS) composites (BE/MCS) was investigated under a statistical design of experiments at a 95% confidence interval to identify the critical factors and to optimize the adsorption capacity. The BE/MCS adsorbents were characterized by means of X-ray diffraction, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller adsorption/desorption isotherms, contact angle analysis (sessile drop technique) and their zeta potential. From the results of a full 2(5) factorial design with three center points, the adsorbent weight and initial pH of the MWF had a significant antagonistic effect on the adsorption capacity while the initial MWF concentration and BE:chitosan:SDS weight ratio had a synergistic influence. Temperature factor has no discernible effect on the capacity. From the FCCC-RSM design, the optimal capacity range of 2840-2922.5 mg g(-1) was achieved at sorbent weight of 1.6-1.9 g, pH of 5.5-6.5, initial MWF concentration of 52-55 g l(-1) and BE:chitosan:SDS (w/w/w) ratio of 4.7:1:1-6.2:1:1. To test the validation and sensitivity of RSM model, the results showed that the estimated adsorption capacity was close to the experimental capacity within an error range of ±3%, suggesting that the RSM model was acceptable and satisfied. From three kinetics models (pseudo-first-order, pseudo-second-order model and Avrami's equation) and two adsorption isotherms (Langmuir model and Freundlich model), assessed using an error function (Err) and the coefficient of determination (R(2)), Avrami's equation and Freundlich isotherm model provided a good fitting for the data, suggesting the presence of more than one reaction pathway in the MWF adsorption process and the heterogeneous surface adsorption of the BC/ABE-5.5 composite. PMID:26731309

  15. Adsorption of emulsified oil from metalworking fluid on activated bleaching earth-chitosan-SDS composites: Optimization, kinetics, isotherms.

    PubMed

    Naowanat, Nitiya; Thouchprasitchai, Nutthavich; Pongstabodee, Sangobtip

    2016-03-15

    The adsorption of emulsified oil from metalworking fluid (MWF) on activated bleaching earth (BE)-chitosan-sodium dodecyl sulfate (SDS) composites (BE/MCS) was investigated under a statistical design of experiments at a 95% confidence interval to identify the critical factors and to optimize the adsorption capacity. The BE/MCS adsorbents were characterized by means of X-ray diffraction, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller adsorption/desorption isotherms, contact angle analysis (sessile drop technique) and their zeta potential. From the results of a full 2(5) factorial design with three center points, the adsorbent weight and initial pH of the MWF had a significant antagonistic effect on the adsorption capacity while the initial MWF concentration and BE:chitosan:SDS weight ratio had a synergistic influence. Temperature factor has no discernible effect on the capacity. From the FCCC-RSM design, the optimal capacity range of 2840-2922.5 mg g(-1) was achieved at sorbent weight of 1.6-1.9 g, pH of 5.5-6.5, initial MWF concentration of 52-55 g l(-1) and BE:chitosan:SDS (w/w/w) ratio of 4.7:1:1-6.2:1:1. To test the validation and sensitivity of RSM model, the results showed that the estimated adsorption capacity was close to the experimental capacity within an error range of ±3%, suggesting that the RSM model was acceptable and satisfied. From three kinetics models (pseudo-first-order, pseudo-second-order model and Avrami's equation) and two adsorption isotherms (Langmuir model and Freundlich model), assessed using an error function (Err) and the coefficient of determination (R(2)), Avrami's equation and Freundlich isotherm model provided a good fitting for the data, suggesting the presence of more than one reaction pathway in the MWF adsorption process and the heterogeneous surface adsorption of the BC/ABE-5.5 composite.

  16. Studies of gas adsorption in flexible Metal-Organic frameworks

    NASA Astrophysics Data System (ADS)

    Sircar, Sarmishtha

    Flexible Metal-Organic frameworks that exhibit a gate-opening (GO) adsorption mechanism have potential for gas separations and gas storage. The GO phenomenon occurs when molecular gates in the structure expand/contract in response to the activation/de-activation of a system variable e.g. temperature, pressure or gas. Sharp discontinuities in the isotherm leading to S-shapes and large adsorption-desorption hysteresis are typical of this phenomenon. This study investigates the kinetics and thermodynamics of the GO behavior by combining adsorption measurements and analytical modeling of adsorption kinetics and capacity as a function of adsorbate, GO pressure, and temperature. Basic understanding of GO mechanism will help harness GO-MOF's as adsorbents for gas separations and storage. Experiments were performed on two precharacterized MOFs with verified GO behavior. These are (1) Zn2(bpdc)2(bpee), which expands from a relative amorphous to crystalline structure and (2) Cu[(dhbc) 2(4,4f-bpy)]H2O, a mutually interdigitated 2-D structure (bpdc = biphenyldicarboxylate, bpee = 1,2]bipyridylethene; DMF = N,N-dimethyl formamide, dhbc= 2,5-dihydroxybenzoic acid, bpy=bipyridine). Both sub- and super-critical adsorption data were collected using three adsorption units: a standard low-pressure volumetric adsorption unit, a commercial high-pressure gravimetric analyzer and a custom-built high-pressure differential volumetric unit. Collected laboratory data were combined with published adsorption rate and isotherm data for analysis to broaden the range of data collection. The accuracy of the high-pressure differential unit was improved by over 300-fold by changing analytical methods of processing data to establish a reliable null correction. A pronounced effect of the allowed experimental time was found at cryogenic temperatures on (1). Tightening the stability criteria used by the adsorption equipment to determine equilibration increased the experimental time from the order of

  17. Molecular structure-adsorption study on current textile dyes.

    PubMed

    Örücü, E; Tugcu, G; Saçan, M T

    2014-01-01

    This study was performed to investigate the adsorption of a diverse set of textile dyes onto granulated activated carbon (GAC). The adsorption experiments were carried out in a batch system. The Langmuir and Freundlich isotherm models were applied to experimental data and the isotherm constants were calculated for 33 anthraquinone and azo dyes. The adsorption equilibrium data fitted more adequately to the Langmuir isotherm model than the Freundlich isotherm model. Added to a qualitative analysis of experimental results, multiple linear regression (MLR), support vector regression (SVR) and back propagation neural network (BPNN) methods were used to develop quantitative structure-property relationship (QSPR) models with the novel adsorption data. The data were divided randomly into training and test sets. The predictive ability of all models was evaluated using the test set. Descriptors were selected with a genetic algorithm (GA) using QSARINS software. Results related to QSPR models on the adsorption capacity of GAC showed that molecular structure of dyes was represented by ionization potential based on two-dimensional topological distances, chromophoric features and a property filter index. Comparison of the performance of the models demonstrated the superiority of the BPNN over GA-MLR and SVR models. PMID:25529487

  18. Optimizing available phosphorus in calcareous soils fertilized with diammonium phosphate and phosphoric acid using Freundlich adsorption isotherm.

    PubMed

    Naeem, Asif; Akhtar, Muhammad; Ahmad, Waqar

    2013-01-01

    In calcareous soils, phosphorus (P) retention and immobilization take place due to precipitation and adsorption. Since soil pH is considered a major soil variable affecting the P sorption, an acidic P fertilizer could result in low P adsorption compared to alkaline one. Therefore, P adsorption from DAP and phosphoric acid (PA) required to produce desired soil solution P concentration was estimated using Freundlich sorption isotherms. Two soils from Faisalabad and T. T. Singh districts were spiked with 0, 10, and 20 % CaCO3 for 15 days. Freundlich adsorption isotherms (P = aC(b/a)) were constructed, and theoretical doses of PA and DAP to develop a desired soil solution P level (i.e., 0.20 mg L(-1)) were calculated. It was observed that P adsorption in soil increased with CaCO3. Moreover, at all the levels of CaCO3, P adsorption from PA was lower compared to that from DAP in both the soils. Consequently, lesser quantity of PA was required to produce desired solution P, 0.2 mg L(-1), compared to DAP. However, extrapolating the developed relationship between soil CaCO3 contents and quantity of fertilizer to other similar textured soils needs confirmation. PMID:24307878

  19. Heavy Metal Adsorption onto Kappaphycus sp. from Aqueous Solutions: The Use of Error Functions for Validation of Isotherm and Kinetics Models

    PubMed Central

    Rahman, Md. Sayedur; Sathasivam, Kathiresan V.

    2015-01-01

    Biosorption process is a promising technology for the removal of heavy metals from industrial wastes and effluents using low-cost and effective biosorbents. In the present study, adsorption of Pb2+, Cu2+, Fe2+, and Zn2+ onto dried biomass of red seaweed Kappaphycus sp. was investigated as a function of pH, contact time, initial metal ion concentration, and temperature. The experimental data were evaluated by four isotherm models (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and four kinetic models (pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion models). The adsorption process was feasible, spontaneous, and endothermic in nature. Functional groups in the biomass involved in metal adsorption process were revealed as carboxylic and sulfonic acids and sulfonate by Fourier transform infrared analysis. A total of nine error functions were applied to validate the models. We strongly suggest the analysis of error functions for validating adsorption isotherm and kinetic models using linear methods. The present work shows that the red seaweed Kappaphycus sp. can be used as a potentially low-cost biosorbent for the removal of heavy metal ions from aqueous solutions. Further study is warranted to evaluate its feasibility for the removal of heavy metals from the real environment. PMID:26295032

  20. Effect of the endcapping of reversed-phase high-performance liquid chromatography adsorbents on the adsorption isotherm

    SciTech Connect

    Gritti, Fabrice; Guiochon, Georges A

    2005-09-01

    The retention mechanisms of n-propylbenzoate, 4-t ert-butylphenol, and caffeine on the endcapped Symmetry-C{sub 18} and the non-endcapped Resolve-C{sub 18} are compared. The adsorption isotherms were measured by frontal analysis (FA), using as the mobile phase mixtures of methanol or acetonitrile and water of various compositions. The isotherm data were modeled and the adsorption energy distributions calculated. The surface heterogeneity increases faster with decreasing methanol concentration on the non-endcapped than on the endcapped adsorbent. For instance, for methanol concentrations exceeding 30% (v/v), the adsorption of caffeine is accounted for by assuming three and two different types of adsorption sites on Resolve-C{sub 18} and Symmetry-C{sub 18}, respectively. This is explained by the effect of the mobile phase composition on the structure of the C{sub 18}-bonded layer. The bare surface of bonded silica appears more accessible to solute molecules at high water contents in the mobile phase. On the other hand, replacing methanol by a stronger organic modifier like acetonitrile dampens the differences between non-endcapped and endcapped stationary phase and decreases the degree of surface heterogeneity of the adsorbent. For instance, at acetonitrile concentrations exceeding 20%, the surface appears nearly homogeneous for the adsorption of caffeine.

  1. Kinetics and isothermal modeling of liquid phase adsorption of rhodamine B onto urea modified Raphia hookerie epicarp

    NASA Astrophysics Data System (ADS)

    Inyinbor, A. A.; Adekola, F. A.; Olatunji, G. A.

    2016-09-01

    Epicarp of Raphia hookerie, a bioresource material, was modified with urea (UMRH) to adsorb Rhodamine B (RhB) from aqueous solution. Adsorbent morphology and surface chemistry were established by Brunauer-Emmett-Teller (BET) surface area determination, Fourier transform infrared spectroscopic (FTIR) analysis, scanning electron microscopy (SEM), as well as the pH point of zero charge (pHpzc) determination. Prepared material was subsequently utilized for the uptake of Rhodamine B (RhB). Operational parameters, such as adsorbent dosage, concentration, time, and temperature, were investigated. Evidence of effective urea modification was confirmed by vivid absorption bands at 1670 and 1472 cm-1 corresponding to C=O and C-N stretching vibrations, respectively. Optimum adsorption was obtained at pH 3. Freundlich adsorption isotherm best fits the equilibrium adsorption data, while evidence of adsorbate-adsorbate interaction was revealed by Temkin isotherm model. The maximum monolayer adsorption capacity (q max) was 434.78 mg/g. Kinetics of the adsorption process was best described by the pseudo-second-order kinetics model. Desorption efficiency was less than or equal to 25 % for all the eluents, and it follows the order HCl > H2O > CH3COOH.

  2. Effect of humic acid on the adsorption/desorption behavior of glyphosate on goethite. Isotherms and kinetics.

    PubMed

    Arroyave, Jeison Manuel; Waiman, Carolina C; Zanini, Graciela P; Avena, Marcelo J

    2016-02-01

    The effects of humic acid (HA) on the adsorption/desorption of glyphosate (Gly) on goethite were investigated under pseudo equilibrium conditions by adsorption isotherms and under kinetic conditions by ATR-FTIR spectroscopy. Isotherms reveal that the attachment of Gly is almost completely inhibited by HA molecules. The opposite effect is not observed: HA adsorption is not affected by the presence of Gly. ATR-FTIR allowed the simultaneous detection of adsorbed HA and Gly during kinetic runs, revealing that HA at the surface decreases markedly the adsorption rate of Gly likely as a result of a decreased availability of sites for Gly adsorption and because of electrostatic repulsion. In addition, HA in solution increases the desorption rate of Gly. The rate law for Gly desorption could be determined giving important insights on the desorption mechanism. The herbicide is desorbed by two parallel processes: i) a direct detachment from the surface, which is first order in adsorbed Gly; and ii) a ligand exchange with HA molecules, which is first order in adsorbed Gly and first order in dissolved HA. Rate constants for both processes were quantified, leading to half-lives of 3.7 h for the first process, and 1.4 h for the second process in a 400 mg L(-1) HA solution. These data are important for modeling the dynamics of glyphosate in environmentally relevant systems, such as soils and surface waters. PMID:26657085

  3. Effect of humic acid on the adsorption/desorption behavior of glyphosate on goethite. Isotherms and kinetics.

    PubMed

    Arroyave, Jeison Manuel; Waiman, Carolina C; Zanini, Graciela P; Avena, Marcelo J

    2016-02-01

    The effects of humic acid (HA) on the adsorption/desorption of glyphosate (Gly) on goethite were investigated under pseudo equilibrium conditions by adsorption isotherms and under kinetic conditions by ATR-FTIR spectroscopy. Isotherms reveal that the attachment of Gly is almost completely inhibited by HA molecules. The opposite effect is not observed: HA adsorption is not affected by the presence of Gly. ATR-FTIR allowed the simultaneous detection of adsorbed HA and Gly during kinetic runs, revealing that HA at the surface decreases markedly the adsorption rate of Gly likely as a result of a decreased availability of sites for Gly adsorption and because of electrostatic repulsion. In addition, HA in solution increases the desorption rate of Gly. The rate law for Gly desorption could be determined giving important insights on the desorption mechanism. The herbicide is desorbed by two parallel processes: i) a direct detachment from the surface, which is first order in adsorbed Gly; and ii) a ligand exchange with HA molecules, which is first order in adsorbed Gly and first order in dissolved HA. Rate constants for both processes were quantified, leading to half-lives of 3.7 h for the first process, and 1.4 h for the second process in a 400 mg L(-1) HA solution. These data are important for modeling the dynamics of glyphosate in environmentally relevant systems, such as soils and surface waters.

  4. Ab initio prediction of adsorption isotherms for small molecules in metal-organic frameworks: the effect of lateral interactions for methane/CPO-27-Mg.

    PubMed

    Sillar, Kaido; Sauer, Joachim

    2012-11-01

    A hybrid method that combines density functional theory for periodic structures with wave function-based electron correlation methods for finite-size models of adsorption sites is employed to calculate energies for adsorption of CH(4) onto different sites in the metal-organic framework (MOF) CPO-27-Mg (Mg-MOF-74) with chemical accuracy. The adsorption energies for the Mg(2+), linker, second layer sites are -27.8, -18.3, and -15.1 kJ/mol. Adsorbate-adsorbate interactions increase the average CH(4) adsorption energy by about 10% (2.4 kJ/mol). The free rotor-harmonic oscillator-ideal gas model is applied to calculate free energies/equilibrium constants for adsorption on the individual sites. This information is used in a multisite Langmuir model, augmented with a Bragg-Williams model for lateral interactions, to calculate adsorption isotherms. This ab initio approach yields the contributions of the individual sites to the final isotherms and also of the lateral interactions that contribute about 15% to the maximum excess adsorption capacity. Isotherms are calculated for both absolute amounts, for calculation of isosteric heats of adsorption as function of coverage, and excess amounts, for comparison with measured isotherms. Agreement with observed excess isotherms is reached if the experimentally determined limited accessibility of adsorption sites (78%) is taken into account.

  5. Adsorption Isotherms for Xenon and Krypton using INL HZ-PAN and AgZ-PAN Sorbents

    SciTech Connect

    Troy G. Garn; Mitchell Greenhalgh; Veronica J. Rutledge; Jack D. Law

    2014-08-01

    The generation of adsorption isotherms compliments the scale-up of off-gas processes used to control the emission of encapsulated radioactive volatile fission and activation products released during Used Nuclear Fuel (UNF) reprocessing activities. A series of experiments were conducted to obtain capacity results for varying Kr and Xe gas concentrations using HZ-PAN and AgZ-PAN engineered form sorbents. Gas compositions for Kr ranged from 150-40,000 ppmv and 250-5020 ppmv for Xe in a helium balance. The experiments were all performed at 220 K at a flowrate of 50 sccm. Acquired capacities were then respectively fit to the Langmuir equation using the Langmuir linear regression method to obtain the equilibrium parameters Qmax and Keq. Generated experimental adsorption isotherms were then plotted with the Langmuir predicted isotherms to illustrate agreement between the two. The Langmuir parameters were provided for input into the OSPREY model to predict breakthrough of single component adsorption of Kr and Xe on HZ-PAN and AgZ-PAN sorbents at the experimental conditions tested. Kr and Xe capacities resulting from model breakthrough predictions were then compared to experimental capacities for model validation.

  6. Studies on Thorium Adsorption Characteristics upon Activated Titanium Hydroxide Prepared from Rosetta Ilmenite Concentrate

    SciTech Connect

    Gado, M Zaki, S

    2016-01-01

    The titanium hydroxide prepared from Rosetta ilmenite concentrate has been applied for Th (IV) adsorption from its acid aqueous solutions. The prepared hydroxide is first characterized by both Fourier transform infrared (FT-IR) spectrum and thermogravimetric analysis. The relevant factors affecting the adsorption process have been studied. The obtained equilibrium data fits well with the Langmuir isotherm rather than Freundlich isotherm, while the adsorption kinetic data follow the pseudo-second order model. The different thermodynamic parameters have also been calculated and indicate that the adsorption process is spontaneous.

  7. Interactions between lignosulphonates and the components of the lead-acid battery. Part 1. Adsorption isotherms

    NASA Astrophysics Data System (ADS)

    Myrvold, Bernt O.

    The expander performs at least five different tasks in the battery. It is a fluidiser for the negative paste. It controls the formation stage of the battery. It controls the shape and size of the lead sulphate crystals formed upon discharge, and thus prevents the sintering of the active mass. It controls the rate of the lead to lead sulphate oxidation during discharge. Finally, it affects the charge acceptance. To gain more understanding of these different effects the interaction between lead, lead(II) oxide, lead(IV) oxide, lead sulphate, barium sulphate and carbon black and the experimental lignosulphonate (LS) expander UP-414 has been investigated. We also compared with Vanisperse A and several other lignosulphonates, to elucidate the mechanisms operating. In most cases, we have studied concentration ranges that are both higher and lower than those normally encountered in batteries. There is no adsorption of lignosulphonates to pure lead surfaces. Adsorption to lead sulphate is a slow process. In the presence of lead ions lignosulphonates will also adsorb to lead. The adsorption to lead(II) oxide is a fast process, and a strong adsorption occurs. In all these cases, it is preferably the high molecular weight fraction that interacts with the solid surfaces. Lead ions leaching from the surface complexes with lignosulphonates to give a more hydrophobic species. This allows the normally negatively charged lignosulphonate to adsorb to the negatively charged substrates. The lignosulphonates have an ability to complex lead ions and keep them solvated. This confirms previous observations of the lignosulphonates ability to promote the dissolution-precipitation mechanism for lead sulphate formation on the expense of the solid-state reaction.

  8. Sonochemical assisted hydrothermal synthesis of ZnO: Cr nanoparticles loaded activated carbon for simultaneous ultrasound-assisted adsorption of ternary toxic organic dye: Derivative spectrophotometric, optimization, kinetic and isotherm study.

    PubMed

    Jamshidi, M; Ghaedi, M; Dashtian, K; Hajati, S; Bazrafshan, A A

    2016-09-01

    Chromium doped zinc oxide nanoparticles (ZnO: Cr-NPs) was synthesized by ultrasonically assisted hydrothermal method and characterized by FE-SEM, XRD and TEM analysis. Subsequently, this composite ultrasonically assisted was deposited on activated carbon (ZnO: Cr-NPs-AC) and used for simultaneous ultrasound-assisted removal of three toxic organic dye namely of malachite green (MG), eosin yellow (EY) and Auramine O (AO). Dyes spectra overlap in mixture (major problem for simultaneous investigation) of this systems was extensively resolved by derivative spectrophotometric method. The magnitude of variables like initial dyes concentration, adsorbent mass and sonication time influence on dyes removal was optimized using small central composite design (CCD) combined with desirability function (DF) approach, while pH was studied by one-a-time approach. The maximized removal percentages at desirability of 0.9740 was set as follow: pH 6.0, 0.019g ZnO: Cr-NPs-AC, 3.9min sonication at 4.5, 4.8 and 4.7mgL(-1) of MG, EY and AO, respectively. Above optimized points lead to achievement of removal percentage of 98.36%, 97.24%, and 99.26% correspond to MG, EY and AO, respectively. ANOVA for each dyes based p-value less than (<0.0001) suggest highly efficiency of CCD model for prediction of data concern to simultaneous removal of these dyes within 95% confidence interval, while their F-value for MG, EY and AO is 935, 800.2, and 551.3, respectively, that confirm low participation of this them in signal. The value of multiple correlation coefficient R(2), adjusted and predicted R(2) for simultaneous removal of MG is 0.9982, 0.9972 and 0.9940, EY is 0.9979, 0.9967 and 0.9930 and for AO is 0.9970, 0.9952 and 0.9939. The adsorption rate well fitted by pseudo second-order and Langmuir model via high, economic and profitable adsorption capacity of 214.0, 189.7 and 211.6mgg(-1) for MG, EY and AO, respectively. PMID:27150752

  9. Sonochemical assisted hydrothermal synthesis of ZnO: Cr nanoparticles loaded activated carbon for simultaneous ultrasound-assisted adsorption of ternary toxic organic dye: Derivative spectrophotometric, optimization, kinetic and isotherm study.

    PubMed

    Jamshidi, M; Ghaedi, M; Dashtian, K; Hajati, S; Bazrafshan, A A

    2016-09-01

    Chromium doped zinc oxide nanoparticles (ZnO: Cr-NPs) was synthesized by ultrasonically assisted hydrothermal method and characterized by FE-SEM, XRD and TEM analysis. Subsequently, this composite ultrasonically assisted was deposited on activated carbon (ZnO: Cr-NPs-AC) and used for simultaneous ultrasound-assisted removal of three toxic organic dye namely of malachite green (MG), eosin yellow (EY) and Auramine O (AO). Dyes spectra overlap in mixture (major problem for simultaneous investigation) of this systems was extensively resolved by derivative spectrophotometric method. The magnitude of variables like initial dyes concentration, adsorbent mass and sonication time influence on dyes removal was optimized using small central composite design (CCD) combined with desirability function (DF) approach, while pH was studied by one-a-time approach. The maximized removal percentages at desirability of 0.9740 was set as follow: pH 6.0, 0.019g ZnO: Cr-NPs-AC, 3.9min sonication at 4.5, 4.8 and 4.7mgL(-1) of MG, EY and AO, respectively. Above optimized points lead to achievement of removal percentage of 98.36%, 97.24%, and 99.26% correspond to MG, EY and AO, respectively. ANOVA for each dyes based p-value less than (<0.0001) suggest highly efficiency of CCD model for prediction of data concern to simultaneous removal of these dyes within 95% confidence interval, while their F-value for MG, EY and AO is 935, 800.2, and 551.3, respectively, that confirm low participation of this them in signal. The value of multiple correlation coefficient R(2), adjusted and predicted R(2) for simultaneous removal of MG is 0.9982, 0.9972 and 0.9940, EY is 0.9979, 0.9967 and 0.9930 and for AO is 0.9970, 0.9952 and 0.9939. The adsorption rate well fitted by pseudo second-order and Langmuir model via high, economic and profitable adsorption capacity of 214.0, 189.7 and 211.6mgg(-1) for MG, EY and AO, respectively.

  10. Study on the methylene blue adsorption from wastewaters by pore-expanded calcium fluoride sludge adsorbent.

    PubMed

    Hong, Junming; Lin, Bing; Hong, Gui-Bing; Chang, Chang-Tang

    2014-04-01

    The adsorption of methylene blue (MB) onto pore-expanded calcium fluoride sludge (ECF) by the batch adsorption technique was investigated. The results showed that the adsorption capacity increased with increasing MB concentration but decreased as pH was increased. In order to investigate the adsorption mechanisms, three simplified isotherm models and kinetic models were used in this study. The best-fit adsorption isotherm was achieved with the Temkin model. Furthermore, the pseudo-second-order kinetic model agreed very well with the dynamical behavior for the adsorption of MB onto ECF. Thermodynamic studies revealed that the adsorption process of MB onto ECF was spontaneous and exothermic. The results indicated that ECF adsorbed MB efficiently and could be used as a waste adsorbent for the removal of cationic dyes in wastewater treatment.

  11. Interpretation of the excess adsorption isotherms of organic eluent components on the surface of reversed-phase adsorbents. Effect on the analyte retention.

    PubMed

    Kazakevich, Y V; LoBrutto, R; Chan, F; Patel, T

    2001-04-13

    The excess adsorption isotherms of acetonitrile, methanol and tetrahydrofuran from water on reversed-phase packings were studied, using 10 different columns packed with C1-C6, C8, C10, C12, and C18 monomeric phases, bonded on the same type of silica. The interpretation of isotherms on the basis of the theory of excess adsorption shows significant accumulation of the organic eluent component on the adsorbent surface on the top of "collapsed" bonded layer. The accumulated amount was shown to be practically independent of the length of alkyl chains bonded to the silica surface. A model that describes analyte retention on a reversed-phase column from a binary mobile phase is developed. The retention mechanism involves a combination of analyte distribution between the eluent and organic adsorbed layer, followed by analyte adsorption on the surface of the bonded phase. A general retention equation for the model is derived and methods for independent measurements of the involved parameters are suggested. The theory was tested by direct measurement of analyte retention from the eluents of varied composition and comparison of the values obtained with those theoretically calculated values. Experimental and theoretically calculated values are in good agreement.

  12. Investigation of adsorption kinetics and isotherm of cellulase and B-Glucosidase on lignocellulosic substrates

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Clear understanding of enzyme adsorption during enzymatic hydrolysis of lignocellulosic biomass is essential to enhance the cost-efficiency of hydrolysis. However, conclusions from literatures often contradicted each other because enzyme adsorption is enzyme, biomass/pretreatment and experimental co...

  13. Can carbon surface oxidation shift the pore size distribution curve calculated from Ar, N2 and CO2 adsorption isotherms? Simulation results for a realistic carbon model

    NASA Astrophysics Data System (ADS)

    Furmaniak, Sylwester; Terzyk, Artur P.; Gauden, Piotr A.; Harris, Peter J. F.; Kowalczyk, Piotr

    2009-08-01

    Using the virtual porous carbon model proposed by Harris et al, we study the effect of carbon surface oxidation on the pore size distribution (PSD) curve determined from simulated Ar, N2 and CO2 isotherms. It is assumed that surface oxidation is not destructive for the carbon skeleton, and that all pores are accessible for studied molecules (i.e., only the effect of the change of surface chemical composition is studied). The results obtained show two important things, i.e., oxidation of the carbon surface very slightly changes the absolute porosity (calculated from the geometric method of Bhattacharya and Gubbins (BG)); however, PSD curves calculated from simulated isotherms are to a greater or lesser extent affected by the presence of surface oxides. The most reliable results are obtained from Ar adsorption data. Not only is adsorption of this adsorbate practically independent from the presence of surface oxides, but, more importantly, for this molecule one can apply the slit-like model of pores as the first approach to recover the average pore diameter of a real carbon structure. For nitrogen, the effect of carbon surface chemical composition is observed due to the quadrupole moment of this molecule, and this effect shifts the PSD curves compared to Ar. The largest differences are seen for CO2, and it is clearly demonstrated that the PSD curves obtained from adsorption isotherms of this molecule contain artificial peaks and the average pore diameter is strongly influenced by the presence of electrostatic adsorbate-adsorbate as well as adsorbate-adsorbent interactions.

  14. Can carbon surface oxidation shift the pore size distribution curve calculated from Ar, N(2) and CO(2) adsorption isotherms? Simulation results for a realistic carbon model.

    PubMed

    Furmaniak, Sylwester; Terzyk, Artur P; Gauden, Piotr A; Harris, Peter J F; Kowalczyk, Piotr

    2009-08-01

    Using the virtual porous carbon model proposed by Harris et al, we study the effect of carbon surface oxidation on the pore size distribution (PSD) curve determined from simulated Ar, N(2) and CO(2) isotherms. It is assumed that surface oxidation is not destructive for the carbon skeleton, and that all pores are accessible for studied molecules (i.e., only the effect of the change of surface chemical composition is studied). The results obtained show two important things, i.e., oxidation of the carbon surface very slightly changes the absolute porosity (calculated from the geometric method of Bhattacharya and Gubbins (BG)); however, PSD curves calculated from simulated isotherms are to a greater or lesser extent affected by the presence of surface oxides. The most reliable results are obtained from Ar adsorption data. Not only is adsorption of this adsorbate practically independent from the presence of surface oxides, but, more importantly, for this molecule one can apply the slit-like model of pores as the first approach to recover the average pore diameter of a real carbon structure. For nitrogen, the effect of carbon surface chemical composition is observed due to the quadrupole moment of this molecule, and this effect shifts the PSD curves compared to Ar. The largest differences are seen for CO(2), and it is clearly demonstrated that the PSD curves obtained from adsorption isotherms of this molecule contain artificial peaks and the average pore diameter is strongly influenced by the presence of electrostatic adsorbate-adsorbate as well as adsorbate-adsorbent interactions. PMID:21828590

  15. Kinetic, isotherm and thermodynamic investigations of phosphate adsorption onto core-shell Fe₃O₄@LDHs composites with easy magnetic separation assistance.

    PubMed

    Yan, Liang-guo; Yang, Kun; Shan, Ran-ran; Yan, Tao; Wei, Jing; Yu, Shu-jun; Yu, Hai-qin; Du, Bin

    2015-06-15

    In this study, three different magnetic core-shell Fe3O4@LDHs composites, Fe3O4@Zn-Al-, Fe3O4@Mg-Al-, and Fe3O4@Ni-Al-LDH were prepared via a rapid coprecipitation method for phosphate adsorptive removal. The composites were characterized by XRD, FTIR, TEM, VSM and BET analyses. Characterization results proved the successful synthesis of core-shell Fe3O4@LDHs composites with good superparamagnetisms. Batch experiments were conducted to study the adsorption efficiency of phosphate. Optimal conditions for the phosphate adsorption were obtained: 0.05 g of adsorbent, solution pH of 3, and contact time of 60 min. Proposed mechanisms for the removal of phosphate species onto Fe3O4@LDHs composites at different initial solution pH were showed. The kinetic data were described better by the pseudo-second-order kinetic equation and KASRA model. The adsorption isotherm curves showed a three-region behavior in the ARIAN model. It had a good fit with Langmuir model and the maximum adsorption capacity followed the order of Fe3O4@Zn-Al-LDH>Fe3O4@Mg-Al-LDH>Fe3O4@Ni-Al-LDH. Thermodynamic analyses indicated that the phosphate adsorption process was endothermic and spontaneous in nature. The three Fe3O4@LDHs composites could be easily separated from aqueous solution by the external magnetic field in 10s. These novel magnetic core-shell Fe3O4@LDHs adsorbents may offer a simple single step adsorption treatment option to remove phosphate from water without the requirement of pre-/post-treatment for current industrial practice.

  16. Adsorption isotherms and structure of cationic surfactants adsorbed on mineral oxide surfaces prepared by atomic layer deposition.

    PubMed

    Wangchareansak, Thipvaree; Craig, Vincent S J; Notley, Shannon M

    2013-12-01

    The adsorption isotherms and aggregate structures of adsorbed surfactants on smooth thin-film surfaces of mineral oxides have been studied by optical reflectometry and atomic force microscopy (AFM). Films of the mineral oxides of titania, alumina, hafnia, and zirconia were produced by atomic layer deposition (ALD) with low roughness. We find that the surface strongly influences the admicelle organization on the surface. At high concentrations (2 × cmc) of cetyltrimethylammonium bromide (CTAB), the surfactant aggregates on a titania surface exhibit a flattened admicelle structure with an average repeat distance of 8.0 ± 1.0 nm whereas aggregates on alumina substrates exhibit a larger admicelle with an average separation distance of 10.5 ± 1.0 nm. A wormlike admicelle structure with an average separation distance of 7.0 ± 1.0 nm can be observed on zirconia substrates whereas a bilayered aggregate structure on hafnia substrates was observed. The change in the surface aggregate structure can be related to an increase in the critical packing parameter through a reduction in the effective headgroup area of the surfactant. The templating strength of the surfaces are found to be hafnia > alumina > zirconia > titania. Weakly templating surfaces are expected to have superior biocompatibility.

  17. Adsorption kinetic and thermodynamic studies of phosphate onto tantalum hydroxide.

    PubMed

    Yu, Shi-Hua; Dong, Xiao-Le; Gong, Hong; Jiang, Heng; Liu, Zhi-Gang

    2012-12-01

    Tantalum hydroxide exhibits the ability for the removal of phosphate from aqueous solution. The kinetic study, adsorption isotherm, thermodynamic study, desorption, and foreign anions effect were examined in batch experiments. The kinetic process was very well described by a pseudo-second-order rate model. The adsorption isotherms showed that phosphate uptake fitted with a Langmuir-type model very well, with an increase of PO4(3-) adsorption capacity from 78.5 to 97.0 mg/g when the temperature increased from 298 to 338 K. The negative values of deltaG(0) and the positive values of deltaH(0) indicated that the phosphate adsorption process was spontaneous and endothermic naturally. While the deltaS(0) values obtained were positive, indicating an increase in randomness at the solid-liquid interface during the adsorption. Foreign anions tests showed that the presence of competitive ions cause minimal interference with the adsorption of phosphate on tantalum hydroxide.

  18. Fundamental studies of methyl iodide adsorption in DABCO impregnated activated carbons.

    PubMed

    Herdes, Carmelo; Prosenjak, Claudia; Román, Silvia; Müller, Erich A

    2013-06-11

    Methyl iodide capture from a water vapor stream using 1,4-diazabicyclo[2.2.2]octane (DABCO)-impregnated activated carbons is, for the first time, fundamentally described here on the atomic level by means of both molecular dynamics and grand canonical Monte Carlo simulations. A molecular dynamics annealing strategy was adopted to mimic the DABCO experimental impregnation procedure in a selected slitlike carbon pore. Predictions, restricted to the micropore region, are made about the adsorption isotherms of methyl iodide, water, and nitrogen on both impregnated and bare activated carbon models. Experimental and simulated nitrogen adsorption isotherms are compared for the validation of the impregnation strategy. Selectivity analyses of the preferential adsorption toward methyl iodide over water are also reported. These simulated adsorption isotherms sum up to previous experimental studies to provide an enhanced picture for this adsorption system of widespread use at nuclear plant HVAC facilities for the capture of radioactive iodine compounds. PMID:23679202

  19. Adsorption mechanism of sodium dodecyl benzene sulfonate on carbon blacks by adsorption isotherm and zeta potential determinations.

    PubMed

    Zhao, Yapei; Lu, Pei; Li, Caiting; Fan, Xiaopeng; Wen, Qingbo; Zhan, Qi; Shu, Xin; Xu, Tieliang; Zeng, Guangming

    2013-01-01

    Surfactant solutions were propounded to remove fine and hydrophobic carbon black particles from coal-fired flue gas. The adsorption mechanisms between sodium dodecyl benzene sulfonate (SDBS, an anionic surfactant) and carbon black particles in suspension were investigated. The influence of inorganic salt (NaCl) was also considered. As results showed, hydrophobic interactions contributed to the strong adsorption between SDBS and carbon black particles in the absence of NaCl, and adding NaCl affected the adsorption process. The adsorption amount of SDBS significantly increased when NaCl was added into the SDBS solution; however, when SDBS was in low concentration, the amount of adsorbed SDBS, which was responsible for the shift of zeta potentials, varied little under different concentrations of NaCl. This indicated that the adsorption of SDBS was mainly caused by hydrophobic interaction and Na+ could not change the adsorption of SDBS on adsorption site when SDBS was in low concentration. Moreover, the adsorbed SDBS and Na+ were retained in the Stern layer. PMID:23530331

  20. Removal of water and iodine by solid sorbents: adsorption isotherms and kinetics

    SciTech Connect

    Lin, R.; Tavlarides, L.L.

    2013-07-01

    Tritium and iodine-129 are two major radioactive elements that are present in off-gases from spent fuel reprocessing plants. Adsorption by solid sorbents is the state-of-the-art technique for removal of these species from off-gases. Modeling and simulating adsorption processes require accurate adsorption equilibrium and kinetic data to permit reasonable estimates of process parameters. We have developed a continuous flow single-pellet adsorption system to gather accurate adsorption equilibrium and kinetic data for adsorption of water by molecular sieve 3A and for adsorption of iodine by silver exchanged mordenite. In this paper, the design of the water and iodine adsorption experimental systems are briefly described and results of water adsorption experiments are presented and discussed. Water uptake curves are fitted with the linear-driving force (LDF) model and the shrinking-core model to determine kinetic parameters. It is shown that the kinetics of water adsorption on zeolite 3A under current experimental conditions is controlled by both the external film resistance and the macro-pore diffusion and can be predicted by both the LDF model and the shrinking-core model with the former one performing slightly better. Preliminary results from iodine adsorption experiments will be presented in the conference.

  1. How realistic is the pore size distribution calculated from adsorption isotherms if activated carbon is composed of fullerene-like fragments?

    PubMed

    Terzyk, Artur P; Furmaniak, Sylwester; Harris, Peter J F; Gauden, Piotr A; Włoch, Jerzy; Kowalczyk, Piotr; Rychlicki, Gerhard

    2007-11-28

    A plausible model for the structure of non-graphitizing carbon is one which consists of curved, fullerene-like fragments grouped together in a random arrangement. Although this model was proposed several years ago, there have been no attempts to calculate the properties of such a structure. Here, we determine the density, pore size distribution and adsorption properties of a model porous carbon constructed from fullerene-like elements. Using the method proposed recently by Bhattacharya and Gubbins (BG), which was tested in this study for ideal and defective carbon slits, the pore size distributions (PSDs) of the initial model and two related carbon models are calculated. The obtained PSD curves show that two structures are micro-mesoporous (with different ratio of micro/mesopores) and the third is strictly microporous. Using the grand canonical Monte Carlo (GCMC) method, adsorption isotherms of Ar (87 K) are simulated for all the structures. Finally PSD curves are calculated using the Horvath-Kawazoe, non-local density functional theory (NLDFT), Nguyen and Do, and Barrett-Joyner-Halenda (BJH) approaches, and compared with those predicted by the BG method. This is the first study in which different methods of calculation of PSDs for carbons from adsorption data can be really verified, since absolute (i.e. true) PSDs are obtained using the BG method. This is also the first study reporting the results of computer simulations of adsorption on fullerene-like carbon models.

  2. Application of novel Polypyrrole/thiol-functionalized zeolite Beta/MCM-41 type mesoporous silica nanocomposite for adsorption of Hg2+ from aqueous solution and industrial wastewater: Kinetic, isotherm and thermodynamic studies

    NASA Astrophysics Data System (ADS)

    Javadian, Hamedreza; Taghavi, Mehdi

    2014-01-01

    Hierarchical zeolite consists of both microporous and unordered mesoporous structures. A composite of Polypyrrole/thiol-functionalized Beta/MCM-41 (PPy/SH-Beta/MCM-41) was prepared, characterized by FE-SEM, FT-IR, XRD, TGA and BET analysis and applied in the investigation of its adsorption characteristics for the removal of Hg2+ ions from aqueous solutions. Thiol-functionalized Beta/MCM-41 (SH-Beta/MCM-41) was prepared by 3-mercaptopropyltrimethoxysilane (MPTMS) in the presence of aerosil-200 as a silica source by two-step hydrothermal crystallization procedure. Batch mode experiments were conducted and three kinetic models were used to describe the adsorption process. The experimental data fitted very well with the Pseudo-second-order kinetic model. The calculated thermodynamic parameters (ΔH, ΔS and ΔG) revealed that the adsorption of Hg2+ onto PPy/SH-Beta/MCM-41 is an endothermic and spontaneous process. It was found that temperature has a positive effect on the removal efficiency and that PPy/SH-Beta/MCM-41 is potentially able to remove Hg2+ ions from aqueous solutions at even high concentrations (400 mg L-1). The recovery of Hg2+ from the PPy/SH-Beta/MCM-41 adsorbent was found to be more than 90% using 0.5 M H2SO4, and the ability of the absorbent to be reused for removal of Hg2+ was investigated.

  3. Temperature dependence of adsorption of PEGylated lysozyme and pure polyethylene glycol on a hydrophobic resin: comparison of isothermal titration calorimetry and van't Hoff data.

    PubMed

    Werner, Albert; Hackemann, Eva; Hasse, Hans

    2014-08-22

    The influence of temperature on the adsorption of PEGylated lysozyme and pure PEG on Toyopearl PPG-600M, a hydrophobic resin, is studied by batch equilibrium measurements and pulse response experiments. Differently PEGylated lysozymes are used for the studies, enabling a systematic variation of the solute properties. Either ammonium sulfate or sodium chloride are added. The enthalpy of adsorption is calculated from a van't Hoff analysis based on these data. It is also directly measured by Isothermal Titration Calorimetry. In the investigated temperature range from 5 °C to 35 °C adsorption is favored by higher temperatures and hence endothermic. The results of the van't Hoff analysis of the equilibrium and the pulse response data agree well. Discrepancies between enthalpies of adsorption obtained by calorimetry and van't Hoff analysis are found and discussed. We conclude that the most likely explanation is that thermodynamic equilibrium is not reached in the experiments even though they were carried out carefully and in the generally accepted way.

  4. Hemoglobin adsorption isotherm at the silica-water interface with evanescent wave cavity ring-down spectroscopy.

    PubMed

    Martin, W Blake; Mirov, Sergey; Martyshkin, Dmitri; Venugopalan, Ramakrishna; Shaw, Andrew M

    2005-01-01

    Evanescent wave cavity ring-down spectroscopy (EW-CRDS) is used to observe the adsorption isotherm for hemoglobin (Hb) from controlled urine samples to assess the potential for rapid diagnosis in hemoglobinuria. The absorbance of Hb at 425 nm is monitored using an alexandrite laser-pumped, room temperature, LiF:F2+** color-center pulsed laser. A minimum absorbance detection level of 2.57 x 10(-4) is achieved, corresponding to a minimum detectable concentration of Hb in urea of 5.8 nM. A multilayered Hb biofilm is formed, and a minimum of eight layers are required to model the adsorption isotherm, allowing for cooperative binding within the layers and extending 56 nm into the interface. A binding constant for Hb to silica 18.23+/-7.58 x 10(6) M is derived, and a binding constant for Hb to Hb in subsequent layers is determined to be 5.631+/-0.432 x 10(5) M. Stoichiometric binding coefficients of 1.530+/-0.981 for layer one and 1.792+/-0.162 for subsequent layers suggest that cooperative binding both to the silica surface and between the layers of the biofilm is important.

  5. Dextran-grafted cation exchanger based on superporous agarose gel: adsorption isotherms, uptake kinetics and dynamic protein adsorption performance.

    PubMed

    Shi, Qing-Hong; Jia, Guo-Dong; Sun, Yan

    2010-07-30

    A novel chromatographic medium for high-capacity protein adsorption was fabricated by grafting dextran (40kDa) onto the pore surfaces of superporous agarose (SA) beads. The bead was denoted as D-SA. D-SA, SA and homogeneous agarose (HA) beads were modified with sulfopropyl (SP) group to prepare cation exchangers, and the adsorption and uptake of lysozyme on all three cation-exchange chromatographic beads (SP-HA, SP-SA and SP-D-SA) were investigated at salt concentrations of 6-50mmol/L. Static adsorption experiments showed that the adsorption capacity of SP-D-SA (2.24mmol/g) was 78% higher than that of SP-SA (1.26mmol/g) and 54% higher than that of SP-HA (1.45mmol/g) at a salt concentration of 6mmol/L. Moreover, salt concentration had less influence on the adsorption capacity and dissociation constant of SP-D-SA than it did on SP-HA, suggesting that dextran-grafted superporous bead is a more potent architecture for chromatographic beads. In the dynamic uptake of lysozyme to the three cation-exchange beads, the D(e)/D(0) (the ratio of effective pore diffusivity to free solution diffusivity) values of 1.6-2.0 were obtained in SA-D-SA, indicating that effective pore diffusivities of SP-D-SA were about two times higher than free solution diffusivity for lysozyme. At 6mmol/L NaCl, the D(e) value in SA-D-SA (22.0x10(-11)m(2)/s) was 14.4-fold greater than that in SP-HA. Due to the superior uptake kinetics in SA-D-SA, the highest dynamic binding capacity (DBC) and adsorption efficiency (the ratio of DBC to static adsorption capacity) was likewise found in SP-D-SA. It is thus confirmed that SP-D-SA has combined the advantages of superporous matrix structure and drafted ligand chemistry in mass transport and offers a new opportunity for the development of high-performance protein chromatography.

  6. Absorption of calcium ions on oxidized graphene sheets and study its dynamic behavior by kinetic and isothermal models

    NASA Astrophysics Data System (ADS)

    Fathy, Mahmoud; Abdel Moghny, Th.; Mousa, Mahmoud Ahmed; El-Bellihi, Abdel-Hameed A.-A.; Awadallah, Ahmed E.

    2016-07-01

    Sorption of calcium ion from the hard underground water using novel oxidized graphene (GO) sheets was studied in this paper. Physicochemical properties and microstructure of graphene sheets were investigated using Raman spectrometer, thermogravimetry analyzer, transmission electron microscope, scanning electron microscope. The kinetics adsorption of calcium on graphene oxide sheets was examined using Lagergren first and second orders. The results show that the Lagergren second-order was the best-fit model that suggests the conception process of calcium ion adsorption on the Go sheets. For isothermal studies, the Langmuir and Freundlich isotherm models were used at temperatures ranging between 283 and 313 K. Thermodynamic parameters resolved at 283, 298 and 313 K indicating that the GO adsorption was exothermic spontaneous process. Finally, the graphene sheets show high partiality toward calcium particles and it will be useful in softening and treatment of hard water.

  7. Chromatographic and traditional albumin isotherms on cellulose: a model for wound protein adsorption on modified cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Albumin is the most abundant protein found in healing wounds. Traditional and chromatogrpahic protein isotherms of albumin binding on modified cotton fibers are useful in understanding albumin binding to cellulose wound dressings. An important consideration in the design of cellulosic wound dressin...

  8. Bayesian and Frequentist Methods for Estimating Joint Uncertainty of Freundlich Adsorption Isotherm Fitting Parameters

    EPA Science Inventory

    In this paper, we present methods for estimating Freundlich isotherm fitting parameters (K and N) and their joint uncertainty, which have been implemented into the freeware software platforms R and WinBUGS. These estimates were determined by both Frequentist and Bayesian analyse...

  9. Determination of adsorption isotherm parameters for minor whey proteins by gradient elution preparative liquid chromatography.

    PubMed

    Faraji, Naeimeh; Zhang, Yan; Ray, Ajay K

    2015-09-18

    Ion-Exchange Chromatography (IEC) techniques have been extensively investigated in protein purification processes, due to the more selective and milder separation steps. To date, existing studies of minor whey proteins fractionation in IEC have primarily been conducted as batch uptake studies, which require more experimental search space, time and materials. In this work, the selected resin's (SP Sepharose FF) equilibrium and dynamic binding capacity were first investigated. Next, adsorption of the pure binary mixture of lactoperoxidase and lactoferrin was studied to calibrate steric mass action (SMA) model using a simplified approach with data from single column experiments. The calibrated model was then verified by performing factorial-design based experiments for various process operating conditions assessing process performance on a larger bed height column. The model predicted results demonstrated a realistic agreement with the experiments providing reproducible column elution profile and reduced experimental work. Finally, whey protein isolate was used to evaluate model parameters in real conditions. Results obtained herein are suitable for future large scale applications.

  10. [Impact of regional water chemistry on the phosphorus isothermal adsorption of the sediments in three subsidence waters of the Huainan Mine areas].

    PubMed

    Yi, Qi-Tao; Sun, Peng-Fei; Xie, Kai; Qu, Xi-Jie; Wang, Ting-Ting

    2013-10-01

    Three research sites of subsidence waters, including Panji (PJ), Guqiao (GQ) and Xieqiao (XQ) located in the Huainan "Panxie" Mine Area have been selected to address their phosphorus (P) adsorption behavior in the sediments considering the site-specific regional water chemistry. The P isothermal adsorption was measured in pure water and four different types of ion solutions, prepared through additions of sodium chloride (NaCl), calcium chloride (CaCl2), sodium bicarbonate (NaHCO3), and a mixture of sodium bicarbonate and calcium chloride (NaHCO3 + CaCI2). The first four settings were studied to analyze the individual impact of each solution on P adsorption while the last one was to study their combined effect. In general, Ca2 + could enhance P adsorption on sediment surfaces while weakly alkaline conditions caused by bicarbonates were unfavorable for its adsorption. As a comprehensive effect, the positive effect of the former was greater than the negative effect of the latter. The zero equilibrium phosphorus concentrations (EPC) in the three sites were 0. 059, 0. 032 and 0. 040 mg.L-1, respectively, showing trends of P releasing to the overlying water column. The site of PJ showed greater P releasing potential than those at the GQ and XQ sites, probably due to its higher nutrient level. Overall, P releasing risks in the researched sediments are weaker than those in eutrophic lakes, while they are very similar to lakes with lower trophic levels, because of their unique sedimentary environments from inundated agricultural soils.

  11. Studies of gas adsorption in flexible Metal-Organic frameworks

    NASA Astrophysics Data System (ADS)

    Sircar, Sarmishtha

    Flexible Metal-Organic frameworks that exhibit a gate-opening (GO) adsorption mechanism have potential for gas separations and gas storage. The GO phenomenon occurs when molecular gates in the structure expand/contract in response to the activation/de-activation of a system variable e.g. temperature, pressure or gas. Sharp discontinuities in the isotherm leading to S-shapes and large adsorption-desorption hysteresis are typical of this phenomenon. This study investigates the kinetics and thermodynamics of the GO behavior by combining adsorption measurements and analytical modeling of adsorption kinetics and capacity as a function of adsorbate, GO pressure, and temperature. Basic understanding of GO mechanism will help harness GO-MOF's as adsorbents for gas separations and storage. Experiments were performed on two precharacterized MOFs with verified GO behavior. These are (1) Zn2(bpdc)2(bpee), which expands from a relative amorphous to crystalline structure and (2) Cu[(dhbc) 2(4,4f-bpy)]H2O, a mutually interdigitated 2-D structure (bpdc = biphenyldicarboxylate, bpee = 1,2]bipyridylethene; DMF = N,N-dimethyl formamide, dhbc= 2,5-dihydroxybenzoic acid, bpy=bipyridine). Both sub- and super-critical adsorption data were collected using three adsorption units: a standard low-pressure volumetric adsorption unit, a commercial high-pressure gravimetric analyzer and a custom-built high-pressure differential volumetric unit. Collected laboratory data were combined with published adsorption rate and isotherm data for analysis to broaden the range of data collection. The accuracy of the high-pressure differential unit was improved by over 300-fold by changing analytical methods of processing data to establish a reliable null correction. A pronounced effect of the allowed experimental time was found at cryogenic temperatures on (1). Tightening the stability criteria used by the adsorption equipment to determine equilibration increased the experimental time from the order of

  12. Interaction of removal Ethidium Bromide with Carbon Nanotube: Equilibrium and Isotherm studies

    PubMed Central

    2014-01-01

    Drinking water resources may be contaminated with Ethidium Bromide (EtBr) which is commonly used in molecular biology laboratories for DNA identification in electrophoresis. Carbon nanotubes are expected to play an important role in sensing, pollution treatment and separation techniques. In this study adsorption of Ethidium Bromide on single-walled carbon nanotubes (SWCNTs) and carboxylate group functionalized single-walled carbon nanotube (SWCNT-COOH) surfaces have been investigated by UV–vis spectrophotometer. The effect of contact time, initial concentration and temperature were investigated. The adsorbents exhibits high efficiency for EtBr adsorption and equilibrium can be achieved in 6 and 3 min for SWCNTs and SWCNT-COOH, respectively. The effect of temperature on adsorption of EtBr by toward adsorbents shows the process in this research has been endothermic. The results showed that the equilibrium data were well described by the Langmuir isotherm model, with a maximum adsorption capacity of 0.770 and 0.830 mg/g for SWCNTs and SWCNT-COOH, respectively. The adsorption of EtBr on SWCNT-COOH is more than SWCNTs surfaces. A comparison of kinetic models was evaluated for the pseudo first-order, pseudo second-order models. Pseudo second-order was found to agree well with the experimental data. PMID:24401790

  13. Adsorption studies of Cu(II) on Boston fern (Nephrolepis exaltata Schott cv. Bostoniensis) leaves

    NASA Astrophysics Data System (ADS)

    Rao, Rifaqat Ali Khan; Khan, Umra

    2016-02-01

    Adsorption studies were done on Boston fern leaves for the effective removal of Cu(II) ions from aqueous solution. It has been tested for the first time for heavy metal adsorption from aqueous solution. This promising material has shown remarkable adsorption capacity towards Cu(II) ions which confirm its novelty, ease of availability, non-toxic nature, cheapness, etc., and give the main innovation to the present study. The adsorbent was analyzed by FT-IR, SEM and EDS. The effect of pH, contact time, initial metal ion concentration and temperature on the adsorption was investigated using batch process to optimize conditions for maximum adsorption. The adsorption of Cu(II) was maximum (96 %) at pH 4. The experimental data were analyzed by Langmuir, Freundlich and Tempkin isotherms. The kinetic studies of Cu(II)were carried out at room temperature (30 °C) in the concentration range 10-100 mg L-1. The data obtained fitted well with the Langmuir isotherm and pseudo-second-order kinetics model. The maximum adsorption capacity (q m) obtained from Langmuir adsorption isotherm was found to be 27.027 mg g-1 at 30 °C. The process was found to be exothermic and spontaneous in nature. The breakthrough and exhaustive capacities were found to be 12.5 and 37.5 mg g-1, respectively. Desorption studies showed that 93.3 % Cu(II) could be desorbed with 0.1 M HCl by continuous mode.

  14. A Comparative Study of the Adsorption of Water and Methanol in Zeolite BEA: A Molecular Simulation Study

    SciTech Connect

    Nguyen, Van T.; Nguyen, Phuong T.; Dang, Liem X.; Mei, Donghai; Wick, Collin D.; Do, Duong D.

    2014-09-15

    Grand Canonical Monte Carlo (GCMC) simulations were carried out to study the equilibrium adsorption concentration of methanol and water in all-silica zeolite BEA over the wide temperature and pressure ranges. For both water and methanol, their adsorptive capacity increases with increasing pressure and decreasing temperature. The onset of methanol adsorption occurs at much lower pressures than water adsorption at all temperatures. Our GCMC simulation results also indicate that the adsorption isotherms of methanol exhibit a gradual change with pressure while water adsorption shows a sharp first-order phase transition at low temperatures. To explore the effects of Si/Al ratio on adsorption, a series of GCMC simulations of water and methanol adsorption in zeolites HBEA with Si/Al=7, 15, 31, 63 were performed. As the Si/Al ratio decreases, the onsets of both water and methanol adsorption dramatically shift to lower pressures. The type V isotherm obtained for water adsorption in hydrophobic BEA progressively changes to type I isotherm with decreasing Si/Al ratio in hydrophilic HBEA. This work was supported by the US Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle.

  15. Predicting Phase Diagram of the CaCl2-H2O Binary System from the BET Adsorption Isotherm

    SciTech Connect

    Ally, Moonis Raza

    2008-01-01

    A recent publication in Fluid Phase Equilibria by Zeng (Zeng, Zhou et al. 2007) claimed remarkable accuracy in predicting the solubility of CaCl2-H2O solutions with the Brunaruer-Emett-Teller (BET) model parameters. Their approach necessarily requires prior knowledge of equilibrium water vapor pressures above saturated solutions as a function of temperature for the hydrates of CaCl2 that exist under those conditions. However, the intrinsic BET model does not require prior knowledge of such solubility data that the approach of (Zeng, Zhou et al. 2007) is dependent upon. This paper highlights the differences between the two approaches and covers a much wider range of compositions and temperatures than is done by (Zeng, Zhou et al. 2007). The statistical mechanical description of multilayer adsorption culminating in the BET adsorption isotherm for aqueous electrolytes as developed by Ally and Braunstein (Ally and Braunstein 1993) is used to predict the liquidus behavior of CaCl2-H2O across the entire composition range (from the melting point of pure water to the melting point of anhydrous calcium chloride), including possible metastable crystalline phases. The method requires as input the two BET parameters r, the statistically averaged number of adsorption sites and ε, the energy of adsorption of water in excess of the energy of condensation of pure water. Usually it suffices to keep r and ε constant, typically evaluated at 298.15 K, but in the case of CaCl2-H2O, it is found that both r and ε must be considered temperature dependent in order to predict the liquidus curve, eutectic and peritectic points with reasonable accuracy over the large temperature and compositional range for this binary system.

  16. Kinetic Batch Soil Adsorption Studies of 2, 4-dinitroanisole (DNAN)

    NASA Astrophysics Data System (ADS)

    Arthur, J.; Mark, N. W.; Taylor, S.; Brusseau, M. L.; Dontsova, K.

    2014-12-01

    Currently the explosive 2, 4, 6- trinitrotoluene (TNT) is used as a main ingredient in munitions; however the compound has failed to meet sensitivity requirements. The replacement compound being tested is 2, 4-dinitroanisole (DNAN). DNAN is less sensitive to shock, high temperatures, and has good detonation characteristics. However, DNAN is more soluble than TNT, which can influence transport and fate behavior and thus bioavailability and exposure potential. DNAN has been shown to have some human and environmental toxicity. The objective of this study was to investigate the environmental fate of DNAN in soil, with a specific focus on sorption processes. Batch experiments were conducted using 11 soils collected from military installations located across the United States. The soils were characterized for pH, specific surface area, electrical conductivity, cation exchange capacity, and organic carbon content. Adsorption kinetic data determined at room temperature were fitted using the first order kinetic equation. Adsorption isotherms were fitted with linear and Freundlich isotherm equations. The magnitudes of the linear adsorption coefficients ranged from 0.6 to 6 cm3/g. Results indicated that the adsorption of DNAN is strongly dependent on the amount of organic carbon present in the soil.

  17. Diethyl phthalate removal from aqueous phase using poly(EGDMA-MATrp) beads: kinetic, isothermal and thermodynamic studies.

    PubMed

    Özer, Elif Tümay; Osman, Bilgen; Kara, Ali; Demirbel, Emel; Beşirli, Necati; Güçer, Şeref

    2015-01-01

    In this study, poly(ethylene glycol dimethacrylate-N-methacryloyl-L-tryptophan methyl ester) [poly(EGDMA-MATrp)] beads (average diameter=106-300 µm), which were synthesized by co-polymerizing of N-methacryloyl-L-tryptophan methyl ester (MATrp) with ethylene glycol dimethacrylate (EGDMA), were used for diethyl phthalate (DEP) adsorption. The various factors affecting the adsorption of DEP from aqueous solutions such as pH, initial concentration, contact time and temperature were analysed. Adsorption behaviour of DEP on the poly(EGDMA-MATrp) beads was investigated by varying pH values of solution, contact time, initial concentration and temperature. An optimum adsorption capacity of 590.7 mg/g for DEP was obtained at 25 °C. The present adsorption process obeyed a pseudo-second-order kinetic model. All the isotherm data can be fitted with the Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. Thermodynamic parameters ΔH=7.745 kJ/mol, ΔS=81.92 J/K/mol and ΔG=-16.69 kJ/mol to -18.31 kJ/mol with the rise in temperature from 25 °C to 45 °C indicated that the adsorption process was endothermic and spontaneous.

  18. Bioremoval of Basic Violet 3 and Acid Blue 93 by Pseudomonas putida and its adsorption isotherms and kinetics.

    PubMed

    Arunarani, A; Chandran, Preethy; Ranganathan, B V; Vasanthi, N S; Sudheer Khan, S

    2013-02-01

    Basic Violet 3 and Acid Blue 93 are the most important group of synthetic colourants extensively used in textile industries for dyeing cotton, wool, silk and nylon. Release of these dye pollutants in to the environment adversely affects the human health and aquatic organisms. The present study we used Pseudomonas putida MTCC 4910 for the adsorptive removal of Basic Violet 3 and Acid Blue 93 from the aqueous solutions. The pH (4-9) and NaCl concentrations (1mM-1M) did not influence the adsorption process. The equilibrium adsorption process fitted well to Freundlich model than Langmuir model. The kinetics of adsorption fitted well by pseudo-second-order. Thus in the present study an attempt has been made to exploit the dye removal capability of P. putida MTCC 4910, and it was found to be an efficient microbe that could be used for bio removal of dyes from textile effluents.

  19. Modeling of boldine alkaloid adsorption onto pure and propyl-sulfonic acid-modified mesoporous silicas. A comparative study.

    PubMed

    Geszke-Moritz, Małgorzata; Moritz, Michał

    2016-12-01

    The present study deals with the adsorption of boldine onto pure and propyl-sulfonic acid-functionalized SBA-15, SBA-16 and mesocellular foam (MCF) materials. Siliceous adsorbents were characterized by nitrogen sorption analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy and thermogravimetric analysis. The equilibrium adsorption data were analyzed using the Langmuir, Freundlich, Redlich-Peterson, and Temkin isotherms. Moreover, the Dubinin-Radushkevich and Dubinin-Astakhov isotherm models based on the Polanyi adsorption potential were employed. The latter was calculated using two alternative formulas including solubility-normalized (S-model) and empirical C-model. In order to find the best-fit isotherm, both linear regression and nonlinear fitting analysis were carried out. The Dubinin-Astakhov (S-model) isotherm revealed the best fit to the experimental points for adsorption of boldine onto pure mesoporous materials using both linear and nonlinear fitting analysis. Meanwhile, the process of boldine sorption onto modified silicas was described the best by the Langmuir and Temkin isotherms using linear regression and nonlinear fitting analysis, respectively. The values of adsorption energy (below 8kJ/mol) indicate the physical nature of boldine adsorption onto unmodified silicas whereas the ionic interactions seem to be the main force of alkaloid adsorption onto functionalized sorbents (energy of adsorption above 8kJ/mol).

  20. Modeling of boldine alkaloid adsorption onto pure and propyl-sulfonic acid-modified mesoporous silicas. A comparative study.

    PubMed

    Geszke-Moritz, Małgorzata; Moritz, Michał

    2016-12-01

    The present study deals with the adsorption of boldine onto pure and propyl-sulfonic acid-functionalized SBA-15, SBA-16 and mesocellular foam (MCF) materials. Siliceous adsorbents were characterized by nitrogen sorption analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy and thermogravimetric analysis. The equilibrium adsorption data were analyzed using the Langmuir, Freundlich, Redlich-Peterson, and Temkin isotherms. Moreover, the Dubinin-Radushkevich and Dubinin-Astakhov isotherm models based on the Polanyi adsorption potential were employed. The latter was calculated using two alternative formulas including solubility-normalized (S-model) and empirical C-model. In order to find the best-fit isotherm, both linear regression and nonlinear fitting analysis were carried out. The Dubinin-Astakhov (S-model) isotherm revealed the best fit to the experimental points for adsorption of boldine onto pure mesoporous materials using both linear and nonlinear fitting analysis. Meanwhile, the process of boldine sorption onto modified silicas was described the best by the Langmuir and Temkin isotherms using linear regression and nonlinear fitting analysis, respectively. The values of adsorption energy (below 8kJ/mol) indicate the physical nature of boldine adsorption onto unmodified silicas whereas the ionic interactions seem to be the main force of alkaloid adsorption onto functionalized sorbents (energy of adsorption above 8kJ/mol). PMID:27612776

  1. Multicomponent adsorption of alcohols onto silicalite-1 from aqueous solution: isotherms, structural analysis, and assessment of ideal adsorbed solution theory.

    PubMed

    Bai, Peng; Tsapatsis, Michael; Siepmann, J Ilja

    2012-11-01

    Configurational-bias Monte Carlo (CBMC) simulations in the isobaric-isothermal version of the Gibbs ensemble (GE) were carried out to probe the adsorption from aqueous solutions of methanol and/or ethanol onto silicalite-1. This methodology does require neither specification of the chemical potential nor any reference to activity models based on experimental data. The CBMC-GE methodology can be applied to the complete range of mixture compositions from pure water to pure alcohols and can also be used when multiple solute types are present at high concentration. The simulations demonstrate high selectivities for the alcohols (α(ethanol) > α(methanol)) almost over the entire composition range. The ideal adsorbed solution theory is found to substantially underpredict the amount of sorbed water and leads to very large errors for low alcohol solution concentrations. The simulations indicate that, at lower loadings, the adsorbed alcohol molecules can serve as seeds for water adsorption but, at higher loadings, alcohols displace water molecules from their preferred region.

  2. Water adsorption isotherms on CH3-, OH-, and COOH-terminated organic surfaces at ambient conditions measured with PM-RAIRS.

    PubMed

    Tu, Aimee; Kwag, Hye Rin; Barnette, Anna L; Kim, Seong H

    2012-10-30

    The water adsorption isotherms on methyl (CH(3))-, hydroxyl (OH)-, and carboxylic acid (COOH)-terminated alkylthiol self-assembled monolayers (SAMs) on Au were studied at room temperature and ambient pressure with polarization modulation reflection-absorption infrared spectroscopy (PM-RAIRS). PM-RAIRS analysis showed that water does not adsorb at all on the CH(3)-SAM/Au at subsaturation humidity conditions. In a dry Ar environment, the OH-SAM/Au holds at least 2 layer thick strongly bound water molecules which exhibit a broad O-H stretch vibration peak centered at ∼3360 cm(-1). The peak position implies that the strongly bound water layer on the OH SAM is more like a liquid than an ice. The additional uptake of water in humid environments is relatively weak, and the peak position changes very little. Unlike the OH-SAM/Au, the COOH-SAM/Au does not have strongly bound water layer. This seems to be due to the strong hydrogen bonding between terminal COOH groups in dry conditions. The weak interactions between water and carboxyl groups at low relative humidity (RH) and the solvation of dissociated carboxylic groups in high RH lead to a type III isotherm behavior, based on the BET categories, for water adsorption on the COOH-SAM/Au. The water spectra on the COOH-SAM at RH > 45% are centered at ∼3430 cm(-1) and very broad, indicating that the hydrogen-bonding network of water on the COOH-SAM is much different from that on the OH-SAM.

  3. Equilibrium and kinetic adsorption study of a cationic dye by a natural adsorbent--silkworm pupa.

    PubMed

    Noroozi, B; Sorial, G A; Bahrami, H; Arami, M

    2007-01-01

    In this work the use of silkworm pupa, which is the waste of silk spinning industries has been investigated as an adsorbent for the removal of C.I. Basic Blue 41. The amino acid nature of the pupa provided a reasonable capability for dye removal. Equilibrium adsorption isotherms and kinetics were investigated. The adsorption equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that adsorption behavior of the dye could be described reasonably well by either Langmuir or Freundlich models. The characteristic parameters for each isotherm have been determined. The monolayer adsorption capacity was determined to be 555 mg/g. Kinetic studies indicated that the adsorption follows pseudo-second-order kinetics with a rate constant of 0.0434 and 0.0572 g/min mg for initial dye concentration of 200 mg/l at 20 and 40 degrees C, respectively. Kinetic studies showed that film diffusion and intra-particle diffusion were simultaneously operating during the adsorption process. The rate constant for intra-particle diffusion was estimated to be 1.985 mg/g min(0.5).

  4. Study of water adsorption on activated carbons with different degrees of surface oxidation

    SciTech Connect

    Salame, I.I.; Bandosz, T.J. |

    1999-02-15

    A carbon of wood origin was oxidized with different oxidizing agents (nitric acid, hydrogen peroxide, and ammonium persulfate). The microstructural properties of the starting material and the oxidized samples were characterized using sorption of nitrogen. The surface acidity was determined using Boehm titration and potentiometric titration. The changes in the surface chemistry were also studied by diffuse reflectance FTIR. Water adsorption isotherms were measured at three different temperatures close to ambient (relative pressure from 0.001 to 0.3). From the isotherms the heats of adsorption were calculated using a virial equation. The results indicated that the isosteric heats of water adsorption are affected by the surface heterogeneity only at low surface coverage. In all cases the limiting heat of adsorption was equal to the heat of water condensation (45 kJ/mol).

  5. A Study of Adsorptive Characteristics of Australian Coals

    NASA Astrophysics Data System (ADS)

    Lan, Y. P.; Tsai, L. L.

    2012-04-01

    Ever since the Kyoto Protocol, controlling carbon dioxide emission and reducing its content in atmosphere are very important environmental issues up to today. One of the effective methods for permanent sequestration of anthropogenic CO2 is to inject CO2 into deep, unminable coal seams and recover coal bed methane at the same time. CO2-ECBM technology had been proved to be very promising to meet the needs of both environment and energy. Beside other external environment factors, capacity of CO2 adsorption and CH4 desorption are the most influencing factors in selection of sites for the geological storage of CO2. Therefore, the objective of this study is to understand the relationship between gas adsorption and CO2 sequestration, by various experiments for the characterization of Australian of coals. Generally speaking, coal seam gas comprises mostly of CH4, CO2, C2H6, and N2. However, some of the Australian coals were reported with significant amount of CO2 up to 90%, which might strongly affect their capacity of CO2 capture and storage (CCS). High to medium volatile bituminous coals from Sydney Basin and Bowen Basin, southeast Australia were selected in this study. Experiments include maceral composition and vitrinite reflectance measurements, petrographic analysis, Proximate analysis, Ultimate analysis, specific surface area analysis as well as CO2 and CH4 adsorption experiments were performed. Parameters for difference adsorption functions (Langmuir, BET, D-R and D-A) were then calculated to fit their adsorption isotherms the best fitting curve can then be found. Among these adsorption functions, Langmuir is the most basic and commonly used function theory. The results of all experiments were synthesized to discuss the relations among each other, so as to establish the relationship between gas adsorption and coal characteristics.

  6. Studying the allosteric energy cycle by isothermal titration calorimetry.

    PubMed

    Martinez-Julvez, Marta; Abian, Olga; Vega, Sonia; Medina, Milagros; Velazquez-Campoy, Adrian

    2012-01-01

    Isothermal titration calorimetry (ITC) is a powerful biophysical technique which allows a complete thermodynamic characterization of protein interactions with other molecules. The possibility of dissecting the Gibbs energy of interaction into its enthalpic and entropic contributions, as well as the detailed additional information experimentally accessible on the intermolecular interactions (stoichiometry, cooperativity, heat capacity changes, and coupled equilibria), make ITC a suitable technique for studying allosteric interactions in proteins. Two experimental methodologies for the characterization of allosteric heterotropic ligand interactions by ITC are described in this chapter, illustrated with two proteins with markedly different structural and functional features: a photosynthetic electron transfer protein and a drug target viral protease.

  7. Use of lipophilic ion adsorption isotherms to determine the surface area and the monolayer capacity of a chromatographic packing, as well as the thermodynamic equilibrium constant for its adsorption.

    PubMed

    Cecchi, T

    2005-04-29

    A method that champions the approaches of two independent research groups, to quantitate the chromatographic stationary phase surface available for lipophilic ion adsorption, is presented. For the first time the non-approximated expression of the electrostatically modified Langmuir adsorption isotherm was used. The non approximated Gouy-Chapman (G-C) theory equation was used to give the rigorous surface potential. The method helps model makers, interested in ionic interactions, determine whether the potential modified Langmuir isotherm can be linearized, and, accordingly, whether simplified retention equations can be properly used. The theory cultivated here allows the estimates not only of the chromatographically accessible surface area, but also of the thermodynamic equilibrium constant for the adsorption of the amphiphile, the standard free energy of its adsorption, and the monolayer capacity of the packing. In addition, it establishes the limit between a theoretical and an empirical use of the Freundlich isotherm to determine the surface area. Estimates of the parameters characterising the chromatographic system are reliable from the physical point of view, and this greatly validates the present comprehensive approach.

  8. Removal of thorium (IV) ions from aqueous solution by a novel nanoporous ZnO: Isotherms, kinetic and thermodynamic studies.

    PubMed

    Kaynar, Ümit H; Ayvacıklı, Mehmet; Hiçsönmez, Ümran; Kaynar, Sermin Çam

    2015-12-01

    The adsorption of thorium (IV) from aqueous solutions onto a novel nanoporous ZnO particles prepared by microwave assisted combustion was studied using batch methods under different experimental conditions. The effect of contact time, solution pH, initial concentration and temperature on adsorption process was studied. The ability of this material to remove Th (IV) from aqueous solution was characterises by Langmuir, Freunlinch and Temkin adsorption isotherms. The adsorption percent and distribution coefficient for nanoporous ZnO powders in optimum conditions were 97% ± 1.02; 8080 L kg(-1)for Th (IV), respectively. Based on the Langmuir model, the maximum adsorption capacity of nanoporous ZnO for Th (IV) was found to be 1500 g kg(-1). Thermodynamic parameters were determined and discussed. The results indicated that nanoporous ZnO was suitable as sorbent material for recovery and adsorption of Th (IV) ions from aqueous solutions. The radioactive Th (VI) in surface water, sea water and waste waters from technologies producing nuclear fuels, mining (uranium and thorium) and laboratories working with radioactive materials (uranium and thorium) can be removed with this nanoporous ZnO.

  9. Numerical determination of non-Langmuirian adsorption isotherms of ibuprofen enantiomers on Chiralcel OD column using ultraviolet-circular dichroism dual detector.

    PubMed

    Li, Hui; Jiang, Xiaoxiao; Xu, Wei; Chen, Yongtao; Yu, Weifang; Xu, Jin

    2016-02-26

    Competitive adsorption isotherm of ibuprofen enantiomers on Chiralcel OD stationary phase at 298K was determined by the application of inverse method. Transport dispersive (TD) chromatography model was used to describe mass balances of the enatiomers. Axial dispersion and mass transfer coefficients were estimated from a series of linear pulse experiments. It was found that the overloaded elution profile of total concentration of racemic ibuprofen cannot be satisfactorily fitted by substituting bi-Langmuir model, the most widely used isotherm model for enantiomers, into TD model and tuning the isotherm parameters. UV-CD dual detector setup was then applied to obtain the individual overloaded elution profiles of both enantiomers. The more informative experimental data revealed non-Langmuirian adsorption behavior of ibuprofen enantiomers on chiralcel OD stationary phase. Two analytical binary isotherm models, both accounting for adsorbate-adsorbate interactions and having the feature of inflection points, were then evaluated. A comparison between quadratic model and Moreau model showed that the former gives better fitting results. The six parameters involved in quadratic model were determined stepwisely. Three of them were first obtained by fitting overloaded elution profiles of S-ibuprofen. The other three were then acquired by fitting overloaded elution profiles of both enantiomers recorded by UV-CD dual detector for racemic ibuprofen. A further attempt was also made at reducing the number of quadratic model parameters. PMID:26846132

  10. Numerical determination of non-Langmuirian adsorption isotherms of ibuprofen enantiomers on Chiralcel OD column using ultraviolet-circular dichroism dual detector.

    PubMed

    Li, Hui; Jiang, Xiaoxiao; Xu, Wei; Chen, Yongtao; Yu, Weifang; Xu, Jin

    2016-02-26

    Competitive adsorption isotherm of ibuprofen enantiomers on Chiralcel OD stationary phase at 298K was determined by the application of inverse method. Transport dispersive (TD) chromatography model was used to describe mass balances of the enatiomers. Axial dispersion and mass transfer coefficients were estimated from a series of linear pulse experiments. It was found that the overloaded elution profile of total concentration of racemic ibuprofen cannot be satisfactorily fitted by substituting bi-Langmuir model, the most widely used isotherm model for enantiomers, into TD model and tuning the isotherm parameters. UV-CD dual detector setup was then applied to obtain the individual overloaded elution profiles of both enantiomers. The more informative experimental data revealed non-Langmuirian adsorption behavior of ibuprofen enantiomers on chiralcel OD stationary phase. Two analytical binary isotherm models, both accounting for adsorbate-adsorbate interactions and having the feature of inflection points, were then evaluated. A comparison between quadratic model and Moreau model showed that the former gives better fitting results. The six parameters involved in quadratic model were determined stepwisely. Three of them were first obtained by fitting overloaded elution profiles of S-ibuprofen. The other three were then acquired by fitting overloaded elution profiles of both enantiomers recorded by UV-CD dual detector for racemic ibuprofen. A further attempt was also made at reducing the number of quadratic model parameters.

  11. Study of Methylene Blue adsorption on keratin nanofibrous membranes.

    PubMed

    Aluigi, A; Rombaldoni, F; Tonetti, C; Jannoke, L

    2014-03-15

    In this work, keratin nanofibrous membranes (mean diameter of about 220nm) were prepared by electrospinning and tested as adsorbents for Methylene Blue through batch adsorption tests. The adsorption capacity of the membranes was evaluated as a function of initial dye concentration, pH, adsorbent dosage, time and temperature. The adsorption capacity increased with increasing the initial dye concentration and pH, while it decreased with increasing the adsorbent dosage and temperature, indicating an exothermic process. The adsorption results indicated that the Langmuir isotherm fitted the experimental data better than the Freundlich and Temkin isotherm models. A mean free energy evaluated through the Dubinin-Radushkevich model of about 16kJmol(-1), indicated a chemisorption process which occurred by ion exchange. The kinetic data were found to fit the pseudo-second-order model better than the pseudo-first-order model. The obtained results suggest that keratin nanofibrous membranes could be promising candidates as dye adsorption filters.

  12. Kinetic and equilibrium studies of adsorptive removal of phenol onto eggshell waste.

    PubMed

    Daraei, H; Mittal, A; Noorisepehr, M; Daraei, F

    2013-07-01

    The aim of the present research is to develop economic, fast, and versatile method for the removal of toxic organic pollutant phenol from wastewater using eggshell. The batch experiments are conducted to evaluate the effect of pH, phenol concentration, dosage of adsorbent, and contact time on the removal of phenol. The paper includes in-depth kinetic studies of the ongoing adsorption process. Attempts have also been made to verify Langmuir and Freundlich adsorption isotherms. The morphology and characteristics of eggshell have also been studied using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and X-ray fluorescence analysis. At ambient temperature, the maximum adsorption of phenol onto eggshells has been achieved at pH 9 and the contact time, 90 min. The experimental data give best-fitted straight lines for pseudo-first-order as well as pseudo-second-order kinetic models. Furthermore, the adsorption process verifies Freundlich and Langmuir adsorption isotherms, and on the basis of mathematical expressions of these models, various necessary adsorption constants have been calculated. Using adsorption data, various thermodynamic parameters like change in enthalpy (∆H(0)), change in entropy (∆S(0)), and change in free energy ∆G(0) have also been evaluated. Results clearly reveal that the solid waste material eggshell acts as an effective adsorbent for the removal of phenol from aqueous solutions. PMID:23274804

  13. Photocatalytic degradation of phenol and phenolic compounds Part I. Adsorption and FTIR study.

    PubMed

    Araña, J; Pulido Melián, E; Rodríguez López, V M; Peña Alonso, A; Doña Rodríguez, J M; González Díaz, O; Pérez Peña, J

    2007-07-31

    With the goal of predicting the photocatalytic behaviour of different phenolic compounds (catechol, resorcinol, phenol, m-cresol and o-cresol), their adsorption and interaction types with the TiO(2) Degussa P-25 surface were studied. Langmuir and Freundlich isotherms were applied in the adsorption studies. The obtained results indicated that catechol adsorption is much higher than those of the other phenolics and its interaction occurs preferentially through the formation of a catecholate monodentate. Resorcinol and the cresols interact by means of hydrogen bonds through the hydroxyl group, and their adsorption is much lower than that of catechol. Finally, phenol showed an intermediate behaviour, with a Langmuir adsorption constant, K(L), much lower than that of catechol, but a similar interaction. The interaction of the selected molecules with the catalyst surface was evaluated by means of FTIR experiments, which allowed us to determine the probability of OH radical attack to the aromatic ring.

  14. Copper adsorption on magnetite-loaded chitosan microspheres: A kinetic and equilibrium study

    NASA Astrophysics Data System (ADS)

    Podzus, P. E.; Debandi, M. V.; Daraio, M. E.

    2012-08-01

    A composite of Fe3O4 nanoparticles and the biopolymer chitosan, chemically crosslinked, was prepared as microspheres and used to adsorb copper ions, which were chosen as a model of contaminant metal in water. The adsorption of copper on the magnetic microspheres was studied in a batch process, with different aqueous solutions of Cu (II) at concentrations ranging from 40 to 1100 ppm. Kinetic and equilibrium aspects of the adsorption process were studied. The time-dependent Cu (II) adsorption data were well described by a pseudo-second-order kinetic model. It was found that the equilibrium data follow the Langmuir isotherm, with a maximum adsorption capacity of around 500 mg Cu/g chitosan. The used microspheres were removed and after desorption the material was able to be reused as an adsorbent. The prepared microspheres proved efficient in the removal of copper ions through an adsorption process whose kinetic and equilibrium characteristics were analyzed.

  15. A Simple Adsorption Experiment

    ERIC Educational Resources Information Center

    Guirado, Gonzalo; Ayllon, Jose A.

    2011-01-01

    The study of adsorption phenomenon is one of the most relevant and traditional physical chemistry experiments performed by chemistry undergraduate students in laboratory courses. In this article, we describe an easy, inexpensive, and straightforward way to experimentally determine adsorption isotherms using pieces of filter paper as the adsorbent…

  16. Phycoremediation and adsorption isotherms of cadmium and copper ions by Merismopedia tenuissima and their effect on growth and metabolism.

    PubMed

    Fawzy, Mustafa A

    2016-09-01

    The current study tends to investigate the removal of cadmium and copper ions by Merismopedia tenuissima, grown in different concentrations of cadmium and copper ions, as well to investigate their effects on growth and metabolism. Sorption isotherms of Langmuir and Freundlich were obtained for the quantitative description of cadmium and copper uptake by M. tenuissima. Langmuir model adequately to describe the data of biosorption for these metals. However, the Freundlich model could work well in case of Cu(2+) only. M. tenuissima appears to be more efficient for removing Cd(2+) ions than Cu(2+). However, the affinity constant of Cu(2+) on the biomass of M. tenuissima was higher than Cd(2+) indicating that M. tenuissima is more tolerant to Cd(2+) phytotoxicity than Cu(2+). FTIR analysis of algae with and without biosorption revealed the presence of carboxyl, amino, amide and hydroxyl groups, which were responsible for biosorption of Cd(+2) and Cu(+2) ions. PMID:27458699

  17. Adsorption and kinetic studies of seven different organic dyes onto magnetite nanoparticles loaded tea waste and removal of them from wastewater samples

    NASA Astrophysics Data System (ADS)

    Madrakian, Tayyebeh; Afkhami, Abbas; Ahmadi, Mazaher

    2012-12-01

    Adsorption of seven different organic dyes from aqueous solutions onto magnetite nanoparticles loaded tea waste (MNLTW) was studied. MNLTW was prepared via a simple method and was fully characterized. The properties of this magnetic adsorbent were characterized by scanning electron microscopy and X-ray diffraction. Adsorption characteristics of the MNLTW adsorbent was examined using Janus green, methylene blue, thionine, crystal violet, Congo red, neutral red and reactive blue 19 as adsorbates. Dyes adsorption process was thoroughly studied from both kinetic and equilibrium points of view for all adsorbents. The experimental isotherm data were analyzed using Langmuir, Freundlich, Sips, Redlich-Peterson, Brouers-Sotolongo and Temkin isotherms. The results from Langmuir isotherm indicated that the capacity of MNLTW for the adsorption of cationic dyes was higher than that for anionic dyes. The adsorption kinetics was tested for the pseudo-first order and pseudo-second order kinetic models at different experimental conditions.

  18. Adsorption and kinetic studies of seven different organic dyes onto magnetite nanoparticles loaded tea waste and removal of them from wastewater samples.

    PubMed

    Madrakian, Tayyebeh; Afkhami, Abbas; Ahmadi, Mazaher

    2012-12-01

    Adsorption of seven different organic dyes from aqueous solutions onto magnetite nanoparticles loaded tea waste (MNLTW) was studied. MNLTW was prepared via a simple method and was fully characterized. The properties of this magnetic adsorbent were characterized by scanning electron microscopy and X-ray diffraction. Adsorption characteristics of the MNLTW adsorbent was examined using Janus green, methylene blue, thionine, crystal violet, Congo red, neutral red and reactive blue 19 as adsorbates. Dyes adsorption process was thoroughly studied from both kinetic and equilibrium points of view for all adsorbents. The experimental isotherm data were analyzed using Langmuir, Freundlich, Sips, Redlich-Peterson, Brouers-Sotolongo and Temkin isotherms. The results from Langmuir isotherm indicated that the capacity of MNLTW for the adsorption of cationic dyes was higher than that for anionic dyes. The adsorption kinetics was tested for the pseudo-first order and pseudo-second order kinetic models at different experimental conditions. PMID:23058993

  19. A Modular Approach To Study Protein Adsorption on Surface Modified Hydroxyapatite.

    PubMed

    Ozhukil Kollath, Vinayaraj; Van den Broeck, Freya; Fehér, Krisztina; Martins, José C; Luyten, Jan; Traina, Karl; Mullens, Steven; Cloots, Rudi

    2015-07-13

    Biocompatible inorganic nano- and microcarriers can be suitable candidates for protein delivery. This study demonstrates facile methods of functionalization by using nanoscale linker molecules to change the protein adsorption capacity of hydroxyapatite (HA) powder. The adsorption capacity of bovine serum albumin as a model protein has been studied with respect to the surface modifications. The selected linker molecules (lysine, arginine, and phosphoserine) can influence the adsorption capacity by changing the electrostatic nature of the HA surface. Qualitative and quantitative analyses of linker-molecule interactions with the HA surface have been performed by using NMR spectroscopy, zeta-potential measurements, X-ray photoelectron spectroscopy, and thermogravimetric analyses. Additionally, correlations to theoretical isotherm models have been calculated with respect to Langmuir and Freundlich isotherms. Lysine and arginine increased the protein adsorption, whereas phosphoserine reduced the protein adsorption. The results show that the adsorption capacity can be controlled with different functionalization, depending on the protein-carrier selections under consideration. The scientific knowledge acquired from this study can be applied in various biotechnological applications that involve biomolecule-inorganic material interfaces. PMID:26096378

  20. A Modular Approach To Study Protein Adsorption on Surface Modified Hydroxyapatite.

    PubMed

    Ozhukil Kollath, Vinayaraj; Van den Broeck, Freya; Fehér, Krisztina; Martins, José C; Luyten, Jan; Traina, Karl; Mullens, Steven; Cloots, Rudi

    2015-07-13

    Biocompatible inorganic nano- and microcarriers can be suitable candidates for protein delivery. This study demonstrates facile methods of functionalization by using nanoscale linker molecules to change the protein adsorption capacity of hydroxyapatite (HA) powder. The adsorption capacity of bovine serum albumin as a model protein has been studied with respect to the surface modifications. The selected linker molecules (lysine, arginine, and phosphoserine) can influence the adsorption capacity by changing the electrostatic nature of the HA surface. Qualitative and quantitative analyses of linker-molecule interactions with the HA surface have been performed by using NMR spectroscopy, zeta-potential measurements, X-ray photoelectron spectroscopy, and thermogravimetric analyses. Additionally, correlations to theoretical isotherm models have been calculated with respect to Langmuir and Freundlich isotherms. Lysine and arginine increased the protein adsorption, whereas phosphoserine reduced the protein adsorption. The results show that the adsorption capacity can be controlled with different functionalization, depending on the protein-carrier selections under consideration. The scientific knowledge acquired from this study can be applied in various biotechnological applications that involve biomolecule-inorganic material interfaces.

  1. Studies on Vapor Adsorption Systems

    NASA Technical Reports Server (NTRS)

    Shamsundar, N.; Ramotowski, M.

    1998-01-01

    The project consisted of performing experiments on single and dual bed vapor adsorption systems, thermodynamic cycle optimization, and thermal modeling. The work was described in a technical paper that appeared in conference proceedings and a Master's thesis, which were previously submitted to NASA. The present report describes some additional thermal modeling work done subsequently, and includes listings of computer codes developed during the project. Recommendations for future work are provided.

  2. Adsorption studies of azotetrazolate and 3,6-dihydrazinotetrazine on peat.

    PubMed

    Borkowski, Andrzej; Rydelek, Paweł; Szala, Mateusz

    2013-01-01

    The objective of our studies was the evaluation of the adsorption process of two high-nitrogen compounds-dihydrazinotetrazine (DHTz) and azotetrazolate ion (AZ)-on a chosen peat. The experiments were performed using a static method at three different temperatures (283, 298, and 333 K). The adsorption process of DHTz and AZ on peat was characterized by isotherms according to the Freundlich and Langmuir models. The obtained correlations between adsorption and equilibrium concentration were in good accordance with the Freundlich and Langmuir models, as confirmed by high values of the correlation coefficients (0.97-0.99). Adsorption of AZ on peat was less efficient than that of DHTz, and this inference was experimentally proven. The maximum surface coverages of peat particles with adsorbate according to the Langmuir model were calculated as 0.02 and 0.17 mol kg(-1) (at 298 K) for AZ and DHTz, respectively. The determined adsorption equilibrium constants confirmed greater adsorption of DHTz on the investigated peat. It can be concluded that adsorption of AZ occurred to a much lesser extent compared to that of DHTz, pointing to a potentially greater threat of migration of soluble azotetrazolates in soil. Standard enthalpies of adsorption estimated for AZ and DHTz were -11.1 and -23.7 kJ mol(-1), respectively. Based on these adsorption enthalpy values, it can be stated that both investigated compounds are adsorbed on peat by a physisorption process.

  3. Adsorption of lead on multi-walled carbon nanotubes with different outer diameters and oxygen contents: kinetics, isotherms and thermodynamics.

    PubMed

    Yu, Fei; Wu, Yanqing; Ma, Jie; Zhang, Chi

    2013-01-01

    The effects of different outer diameters and surface oxygen contents on the adsorption of heavy metals onto six types of multi-walled carbon nanotubes (MWCNTs) were investigated in an aqueous solution and lead was chosen as a model metal ion. The results indicated that the percentage removal and adsorption capacity of lead remarkably increased with decreasing outer diameter due to larger specific surface area (SSA). The SSA-normalized maximum adsorption capacity (qmSSA) and SSA-normalized adsorption coefficient (Kd/SSA) were strongly positively correlated with surface oxygen content, implying that lead adsorption onto MWCNTs significantly increases with the rise of oxygen content and decreases with decreasing SSA. The calculated thermodynamic parameters indicated that adsorption of lead on MWCNTs was endothermic and spontaneous. When the oxygen content of MWCNTs increased from 2.0% to 5.9%, the standard free energy (deltaG0) became more negative, which implied that the oxygenated functional groups increased the adsorption affinity of MWCNTs for lead. Through calculation of enthalpy (deltaH0), deltaG0 and free energy of adsorption (Ea), lead adsorption onto MWCNTs was recognized as a chemisorption process. The chemical interaction between lead and the phenolic groups of MWCNTs could be one of the main adsorption mechanisms due to highly positive correlations between the phenolic groups and Kd/SSA or qm/SSA.

  4. A study on the adsorption of methylene blue onto gum ghatti/TiO2 nanoparticles-based hydrogel nanocomposite.

    PubMed

    Mittal, Hemant; Ray, Suprakas Sinha

    2016-07-01

    The objective of this work was to study the isotherm and kinetic models for the adsorption of methylene blue (MB) onto a TiO2 nanoparticle (TiO2NP)-containing hydrogel nanocomposite (HNC) of polyacrylamide-grafted gum ghatti (PAAm-g-Gg). The grafting of PAAm onto Gg was conducted using N,N'-methylene-bis-acrylamide (MBA) as a crosslinker, and different weight percentages of TiO2NPs were incorporated into the hydrogel matrix during the grafting reaction. The graft co-polymerization and the formation of the HNC were confirmed using FTIR, XRD, BET, SEM, TEM and EDS analyses. The adsorption of MB was studied in batch mode and it was found to be highly dependent on solution pH, ionic strength temperature and adsorbent loading. The MB-adsorption process followed the pseudo-second-order rate model and Langmuir adsorption isotherm with a maximum adsorption capacity of 1305.5mgg(-1). Thermodynamic studies revealed that the adsorption of MB onto the HNC surface was spontaneous, endothermic and through a process of physisorption. The results also showed that the HNC was much more effective for the adsorption of cationic dyes than anionic dyes, and it retained its original adsorption capacity for five successive cycles of adsorption-desorption. In conclusion, the hydrogel nanocomposite showed huge potential for remediating industrial wastewater polluted by toxic cationic dyes.

  5. A study on the adsorption of methylene blue onto gum ghatti/TiO2 nanoparticles-based hydrogel nanocomposite.

    PubMed

    Mittal, Hemant; Ray, Suprakas Sinha

    2016-07-01

    The objective of this work was to study the isotherm and kinetic models for the adsorption of methylene blue (MB) onto a TiO2 nanoparticle (TiO2NP)-containing hydrogel nanocomposite (HNC) of polyacrylamide-grafted gum ghatti (PAAm-g-Gg). The grafting of PAAm onto Gg was conducted using N,N'-methylene-bis-acrylamide (MBA) as a crosslinker, and different weight percentages of TiO2NPs were incorporated into the hydrogel matrix during the grafting reaction. The graft co-polymerization and the formation of the HNC were confirmed using FTIR, XRD, BET, SEM, TEM and EDS analyses. The adsorption of MB was studied in batch mode and it was found to be highly dependent on solution pH, ionic strength temperature and adsorbent loading. The MB-adsorption process followed the pseudo-second-order rate model and Langmuir adsorption isotherm with a maximum adsorption capacity of 1305.5mgg(-1). Thermodynamic studies revealed that the adsorption of MB onto the HNC surface was spontaneous, endothermic and through a process of physisorption. The results also showed that the HNC was much more effective for the adsorption of cationic dyes than anionic dyes, and it retained its original adsorption capacity for five successive cycles of adsorption-desorption. In conclusion, the hydrogel nanocomposite showed huge potential for remediating industrial wastewater polluted by toxic cationic dyes. PMID:26997239

  6. Kinetic study for copper adsorption onto soil minerals in the absence and presence of humic acid.

    PubMed

    Komy, Zanaty R; Shaker, Ali M; Heggy, Said E M; El-Sayed, Mohamed E A

    2014-03-01

    Equilibrium and kinetics of Cu(2+) adsorption onto soil minerals (kaolinite and hematite) in the absence and presence of humic acid have been investigated under various conditions. The influences of ionic strength, pH and solution cations on the rate of the adsorption have been studied. The rate and the amount of adsorbed Cu(2+) onto soil minerals in the absence or the presence of humic acid increased with decreasing ionic strength, increasing pH and in the presence of the background electrolyte K(+) rather than Ca(2+). Humic acid enhanced the rate and the amount of adsorbed Cu(2+) onto soil minerals. The adsorption equilibrium data showed that adsorption behavior of Cu(2+) could be described more reasonably by Langmiur adsorption isotherm than Freundlich isotherm in the absence or presence of humic acid. Pseudo first and pseudo second order models were used to evaluate the kinetic data and the rate constants. The results indicated that the adsorption of Cu(2+) onto hematite and kaolinite in the absence and presence of humic acid is more conforming to pseudo second order kinetics.

  7. Adsorption Studies of Chromium(VI) on Activated Carbon Derived from Mangifera indica (Mango) Seed Shell

    NASA Astrophysics Data System (ADS)

    Mise, Shashikant; Patil, Trupti Nagendra

    2015-09-01

    The removal of chromium(VI) from synthetic sample by adsorption on activated carbon prepared from Mangifera indica (mango) seed shell have been carried out at room temperature 32 ± 1 °C. The removal of chromium(VI) from synthetic sample by adsorption on two types of activated carbon, physical activation and chemical activation (Calcium chloride and Sodium chloride), Impregnation Ratio's (IR) 0.25, 0.50, 0.75 for optimum time, optimum dosages and variation of pH were studied. It is observed that contact time differs for different carbons i.e. for physically and chemically activated carbons. The contact time decreases for chemically activated carbon compared to the physically activated carbon. It was observed that as dosage increases the adsorption increased along with the increase in impregnation ratio. It was also noted that as I.R. increases the surface area of Mangifera indica shell carbon increased. These dosage data were considered in the construction of isotherms and it was found that adsorption obeys Freundlich Isotherm and does not obey Langmuir Isotherm. The maximum removal of chromium (VI) was obtained in highly acidic medium at a pH of 1.50.

  8. Isothermal Microcalorimetry To Study Drugs against Schistosoma mansoni▿

    PubMed Central

    Manneck, Theresia; Braissant, Olivier; Haggenmüller, Yolanda; Keiser, Jennifer

    2011-01-01

    Alternative antischistosomal drugs are required since praziquantel is virtually the only drug available for treatment and morbidity control of schistosomiasis. Manual microscopic reading is the current “gold standard” to assess the in vitro antischistosomal properties of test drugs; however, it is labor-intensive, subjective, and difficult to standardize. Hence, there is a need to develop novel tools for antischistosomal drug discovery. The in vitro effects of praziquantel, oxamniquine, artesunate, and mefloquine on metabolic activity and parasite motility of Schistosoma mansoni (newly transformed schistosomula [NTS] and 49-day-old adult worms) were studied using isothermal microcalorimetry (IMC). Results were compared to morphological readouts of viability. Results obtained for the four drugs tested with phenotypic evaluation by microscopy and IMC showed a good correlation, but IMC also identified drug effects that were not visible by microscopic evaluation, and IMC precisely determined the onset of action of the test drugs. Similar sensitivities on NTS and adult schistosomes were observed for praziquantel and mefloquine, while slight differences in the drug susceptibilities of the two developmental stages were noted with oxamniquine and artesunate. IMC is a useful tool for antischistosomal drug discovery that should be further validated. In addition, our data support the use of NTS in in vitro antischistosomal drug assays. PMID:21270220

  9. Equilibrium, kinetic and thermodynamic study of cesium adsorption onto nanocrystalline mordenite from high-salt solution.

    PubMed

    Lee, Keun-Young; Park, Minsung; Kim, Jimin; Oh, Maengkyo; Lee, Eil-Hee; Kim, Kwang-Wook; Chung, Dong-Yong; Moon, Jei-Kwon

    2016-05-01

    In this study, the equilibrium, kinetics and thermodynamics of cesium adsorption by nanocrystalline mordenite were investigated under cesium contamination with high-salt solution, simulating the case of an operation and decommissioning of nuclear facilities or an accident during the processes. The adsorption rate constants were determined using a pseudo second-order kinetic model. The kinetic results strongly demonstrated that the cesium adsorption rate of nano mordenite is extremely fast, even in a high-salt solution, and much faster than that of micro mordenite. In the equilibrium study, the Langmuir isotherm model fit the cesium adsorption data of nano mordenite better than the Freundlich model, which suggests that cesium adsorption onto nano mordenite is a monolayer homogeneous adsorption process. The obtained thermodynamic parameters indicated that the adsorption involved a very stable chemical reaction. In particular, the combination of rapid particle dispersion and rapid cesium adsorption of the nano mordenite in the solution resulted in a rapid and effective process for cesium removal without stirring, which may offer great advantages for low energy consumption and simple operation.

  10. Equilibrium, kinetic and thermodynamic study of cesium adsorption onto nanocrystalline mordenite from high-salt solution.

    PubMed

    Lee, Keun-Young; Park, Minsung; Kim, Jimin; Oh, Maengkyo; Lee, Eil-Hee; Kim, Kwang-Wook; Chung, Dong-Yong; Moon, Jei-Kwon

    2016-05-01

    In this study, the equilibrium, kinetics and thermodynamics of cesium adsorption by nanocrystalline mordenite were investigated under cesium contamination with high-salt solution, simulating the case of an operation and decommissioning of nuclear facilities or an accident during the processes. The adsorption rate constants were determined using a pseudo second-order kinetic model. The kinetic results strongly demonstrated that the cesium adsorption rate of nano mordenite is extremely fast, even in a high-salt solution, and much faster than that of micro mordenite. In the equilibrium study, the Langmuir isotherm model fit the cesium adsorption data of nano mordenite better than the Freundlich model, which suggests that cesium adsorption onto nano mordenite is a monolayer homogeneous adsorption process. The obtained thermodynamic parameters indicated that the adsorption involved a very stable chemical reaction. In particular, the combination of rapid particle dispersion and rapid cesium adsorption of the nano mordenite in the solution resulted in a rapid and effective process for cesium removal without stirring, which may offer great advantages for low energy consumption and simple operation. PMID:26683820

  11. [Study on treatment of methylene blue wastewater by fly ash adsorption-Fenton and thermal regeneration].

    PubMed

    Bai, Yu-Jie; Zhang, Ai-Li; Zhou, Ji-Ti

    2012-07-01

    The physicochemical properties of water-washed fly ash (FA) and acid modified fly ash (M-FA) were investigated. The adsorption of methylene blue by FA and M-FA were studied by batch experiments. Two methods, Fenton-drive oxidation regeneration and thermal regeneration, were used for regeneration of the used FA and M-FA. The result showed that the rate of adsorption process followed the second order kinetics and the adsorption followed Langmuir isotherms. The adsorption equilibrium time was 30 min, and the equilibrium adsorption capacity of FA and M-FA were 4.22 mg x g(-1) and 5.98 mg x g(-1) respectively. The adsorption capability of M-FA was higher than that of FA. In the range of pH 2-12, the adsorption capacity of M-FA increased with the increase of pH, whereas the adsorption capacity of FA decreased slowly until the pH 8 and then increased. Electrostatic adsorption was the major factor on the adsorption capacity. Around 61% and 55% percentage regeneration (PR) were obtained for FA and M-FA respectively when 78.4 mmol x L(-1) H2O2 and 0.72 mmol x L(-1) Fe2+ were used. When the condition of thermal regeneration was 400 degrees C and 2 h, a positive correlation can be found between the PRs of FA and regeneration times, the PRs were 102%, 104% and 107% in three cycles of adsorption-thermal regeneration process. However a negative correlation can be found between the PRs of M-FA and regeneration times, the PRs were 82%, 75% and 74% in three cycles of adsorption-thermal regeneration process. The PR of FA was higher than that of M-FA, and thermal regeneration was superior to Fenton-drive regeneration. PMID:23002621

  12. [Study on treatment of methylene blue wastewater by fly ash adsorption-Fenton and thermal regeneration].

    PubMed

    Bai, Yu-Jie; Zhang, Ai-Li; Zhou, Ji-Ti

    2012-07-01

    The physicochemical properties of water-washed fly ash (FA) and acid modified fly ash (M-FA) were investigated. The adsorption of methylene blue by FA and M-FA were studied by batch experiments. Two methods, Fenton-drive oxidation regeneration and thermal regeneration, were used for regeneration of the used FA and M-FA. The result showed that the rate of adsorption process followed the second order kinetics and the adsorption followed Langmuir isotherms. The adsorption equilibrium time was 30 min, and the equilibrium adsorption capacity of FA and M-FA were 4.22 mg x g(-1) and 5.98 mg x g(-1) respectively. The adsorption capability of M-FA was higher than that of FA. In the range of pH 2-12, the adsorption capacity of M-FA increased with the increase of pH, whereas the adsorption capacity of FA decreased slowly until the pH 8 and then increased. Electrostatic adsorption was the major factor on the adsorption capacity. Around 61% and 55% percentage regeneration (PR) were obtained for FA and M-FA respectively when 78.4 mmol x L(-1) H2O2 and 0.72 mmol x L(-1) Fe2+ were used. When the condition of thermal regeneration was 400 degrees C and 2 h, a positive correlation can be found between the PRs of FA and regeneration times, the PRs were 102%, 104% and 107% in three cycles of adsorption-thermal regeneration process. However a negative correlation can be found between the PRs of M-FA and regeneration times, the PRs were 82%, 75% and 74% in three cycles of adsorption-thermal regeneration process. The PR of FA was higher than that of M-FA, and thermal regeneration was superior to Fenton-drive regeneration.

  13. Adsorption of water on porous Vycor glass studied by ellipsometry.

    PubMed

    Alvarez-Herrero, A; Heredero, R L; Bernabeu, E; Levy, D

    2001-02-01

    The variation of the optical properties of porous Vycor glass (Corning, Model 7930) under different relative-humidity conditions was studied. The adsorption of water into the glass pores was investigated with spectroscopic ellipsometry. The change of the refractive index was Deltan approximately 0.04 between 5% and 90% relative humidity. A linear relation between the ellipsometer parameter tan Psi, the amount of water adsorbed in the glass pores, and information about the pore-size distributions was established. The results are in accord with the values obtained from N2 isotherms, transmission electron microscope micrographs, and the manufacturer's specifications (radius of approximately 20 A). The possibility of using this material as a transducer for implementation in a fiber-optic sensor to measure humidity was evaluated. PMID:18357027

  14. The Freundlich adsorption isotherm constants and prediction of phosphorus bioavailability as affected by different phosphorus sources in two Kansas soils.

    PubMed

    Shafqat, Mustafa N; Pierzynski, Gary M

    2014-03-01

    Phosphorus (P) adsorption onto soil constituents influences P bioavailability from both agronomic and environmental perspectives. In this study, the P availability from different P sources along with utility of Freundlich adsorption coefficients on the predictability of various crop growth parameters were assessed. Two soils were amended with 150mgPkg(-1) each from six different P sources comprised of manures from two types of ruminants animals, three types of monogastric animals, and inorganic P fertilizer. Corn (Zea mays) was grown and harvested seven times under greenhouse conditions to remove P from the P amended treatments. The application of all P sources reduced the value of Freundlich K and increased the value of Freundlich 1/n and equilibrium P concentration (EPC0) in both soils compared to the un-amended control before cropping. The swine (Sus scrofa) manure (HM) resulted in significant smaller values of Freundlich K and larger values of 1/n in the P deficient Eram-Lebo soil compared to other P sources while, the opposite was true for the turkey (Meleagris gallopava) litter (TL) in the Ulysses soil. The corn biomass, tissue P concentration and P uptake were significantly influenced by all P sources during the first harvest and the total P uptake during seven harvests in both soils compared to the control treatment. Both Freundlich coefficients had strong relationships with the aforementioned corn parameters in the P deficient Eram-Lebo soil while, strength of the association was weak or missing in the Ulysses soil which had optimum levels of antecedent P. PMID:24238913

  15. The Freundlich adsorption isotherm constants and prediction of phosphorus bioavailability as affected by different phosphorus sources in two Kansas soils.

    PubMed

    Shafqat, Mustafa N; Pierzynski, Gary M

    2014-03-01

    Phosphorus (P) adsorption onto soil constituents influences P bioavailability from both agronomic and environmental perspectives. In this study, the P availability from different P sources along with utility of Freundlich adsorption coefficients on the predictability of various crop growth parameters were assessed. Two soils were amended with 150mgPkg(-1) each from six different P sources comprised of manures from two types of ruminants animals, three types of monogastric animals, and inorganic P fertilizer. Corn (Zea mays) was grown and harvested seven times under greenhouse conditions to remove P from the P amended treatments. The application of all P sources reduced the value of Freundlich K and increased the value of Freundlich 1/n and equilibrium P concentration (EPC0) in both soils compared to the un-amended control before cropping. The swine (Sus scrofa) manure (HM) resulted in significant smaller values of Freundlich K and larger values of 1/n in the P deficient Eram-Lebo soil compared to other P sources while, the opposite was true for the turkey (Meleagris gallopava) litter (TL) in the Ulysses soil. The corn biomass, tissue P concentration and P uptake were significantly influenced by all P sources during the first harvest and the total P uptake during seven harvests in both soils compared to the control treatment. Both Freundlich coefficients had strong relationships with the aforementioned corn parameters in the P deficient Eram-Lebo soil while, strength of the association was weak or missing in the Ulysses soil which had optimum levels of antecedent P.

  16. Generalized adsorption isotherms for molecular and dissociative adsorption of a polar molecular species on two polar surface geometries: Perovskite (100) (Pm-3m) and fluorite (111) (Fm-3m)

    DOE PAGES

    Danielson, Thomas; Hin, Celine; Savara, Aditya

    2016-08-10

    Lattice based kinetic Monte Carlo (KMC) simulations have been used to determine a functional form for the second order adsorption isotherms on two commonly investigated crystal surfaces: the (111) fluorite surface and the (100) perovskite surface which has the same geometric symmetry as the NaCl (100) surface. The functional form is generalized to be applicable to all values of the equilibrium constant by a shift along the pressure axis. Functions have been determined for estimating the pressure at which a desired coverage would be achieved and for estimating the coverage at a certain pressure. The generalized form has been calculatedmore » by investigating the surface adsorbate coverage across a range of thermodynamic equilibrium constants that span the range 10-26 to 1013. Finally, the equations have been shown to be general for any value of the adsorption equilibrium constant.« less

  17. Generalized adsorption isotherms for molecular and dissociative adsorption of a polar molecular species on two polar surface geometries: Perovskite (100) (Pm-3m) and fluorite (111) (Fm-3m)

    NASA Astrophysics Data System (ADS)

    Danielson, Thomas; Hin, Celine; Savara, Aditya

    2016-08-01

    Lattice based kinetic Monte Carlo simulations have been used to determine a functional form for the second order adsorption isotherms on two commonly investigated crystal surfaces: the (111) fluorite surface and the (100) perovskite surface which has the same geometric symmetry as the NaCl (100) surface. The functional form is generalized to be applicable to all values of the equilibrium constant by a shift along the pressure axis. Functions have been determined for estimating the pressure at which a desired coverage would be achieved and, conversely, for estimating the coverage at a certain pressure. The generalized form has been calculated by investigating the surface adsorbate coverage across a range of thermodynamic equilibrium constants that span the range 10-26 to 1013. The equations have been shown to be general for any value of the adsorption equilibrium constant.

  18. Application of AlMCM-41 for competitive adsorption of methylene blue and rhodamine B: Thermodynamic and kinetic studies.

    PubMed

    Eftekhari, S; Habibi-Yangjeh, A; Sohrabnezhad, Sh

    2010-06-15

    AlMCM-41 was applied for adsorption of methylene blue (MB) and rhodamine B (RB) in single and binary component systems. In the single component systems, AlMCM-41 represents higher adsorption capacity for MB than RB with the maximal adsorption capacity of 2.08x10(-4) and 8.74x10(-5)mol/g at 25 degrees C for MB and RB, respectively. In the binary component system, MB and RB exhibit competitive adsorption onto the adsorbent. The adsorption is approximately reduced to 94 and 79% of single component adsorption systems for MB and RB (initial concentration of 8x10(-6)M) at 25 degrees C. In single and binary component systems, kinetic and adsorption isotherm studies demonstrate that the data are following pseudo-second-order kinetic model and Langmuir isotherm. Effect of solution pH on the adsorption in single and binary component systems was studied and the results were described by electrostatic interactions.

  19. Maghemite nanosorbcats for methylene blue adsorption and subsequent catalytic thermo-oxidative decomposition: Computational modeling and thermodynamics studies.

    PubMed

    El-Qanni, Amjad; Nassar, Nashaat N; Vitale, Gerardo; Hassan, Azfar

    2016-01-01

    In this study methylene blue (MB) has been investigated for its adsorption and subsequent catalytic thermo-oxidative decomposition on surface of maghemite (γ-Fe2O3) nanoparticles. The experimental adsorption isotherm fit well to the Freundlich model, indicating multi-sites adsorption. Computational modeling of the interaction between the MB molecule and γ-Fe2O3 nanoparticle surface was carried out to get more insights into its adsorption behavior. Adsorption energies of MB molecules on the surface indicated that there are different adsorption sites on the surface of γ-Fe2O3 confirming the findings regarding the adsorption isotherm. The catalytic activity of the γ-Fe2O3 nanoparticles toward MB thermo-oxidative decomposition has been confirmed by subjecting the adsorbed MB to a thermo oxidation process up to 600 °C in a thermogravimetric analyzer. The experimental results showed a catalytic activity for post adsorption oxidation. The oxidation kinetics were studied using the Ozawa-Flyn-Wall (OFW) corrected method. The most probable mechanism functions were fifth and third orders for virgin MB and MB adsorbed onto γ-Fe2O3 nanoparticles, respectively. Moreover, the results of thermodynamic transition state parameters, namely changes in Gibbs free energy of activation (ΔG(‡)), enthalpy of activation (ΔH(‡)), and entropy of activation (ΔS(‡)), emphasized the catalytic activity of γ-Fe2O3 nanoparticles toward MB oxidation.

  20. Arsenic(III) Removal from Contaminated Water using Silica Ceramic: A Batch Adsorption Study

    NASA Astrophysics Data System (ADS)

    Salim, Md.; Munekage, Yukihiro; Naing, Kyaw Min

    The silica ceramic (S-K) has been used as a potential low-cost adsorbent for the removal of As(III) from contaminated water in batch studies. Results showed that an adsorbent dose at 90 g L1 could effectively remove 96% of As(III) from initial concentration of 0.5 mg L1 within 3 h. It was also reveled that As(III) uptake increased with increasing contact time and As(III) concentration decreased with increasing adsorbent dosage. It was observed that As(III) removal is relatively dependent on pH and temperature variations. High adsorption of As(III) was found at pH 7.5 and at 25°C. The adsorption equilibrium data followed both Langmuir and Freundlich isotherms. The Freundlich isotherm provided the best correlation for the adsorption of As(III) onto the silica ceramic. The maximum capacity of adsorption was found (qm) 1.1041 mg g1 at different concentrations at 40 g L1 fixed adsorption dosage. The results suggest that silica ceramic (S-K) is a potential adsorbent for removal As(III) ions effectively from contaminated water.

  1. Comparative study on the adsorption capacity of raw and modified litchi pericarp for removing Cu(II) from solutions.

    PubMed

    Kong, Zhenglei; Li, Xiaochen; Tian, Jiyu; Yang, Jili; Sun, Shujuan

    2014-02-15

    The adsorption of Cu(II) onto raw litchi pericarp (LP) and modified litchi pericarp (MLP) as a function of pH, adsorbent dose and contact time, were investigated. Adsorption equilibrium isotherms, kinetics, and thermodynamics were studied to characterize the adsorption process. Leaching assays were also conducted to evaluate the potential contamination risk of LP and MLP to aqueous systems. The maximum adsorption of Cu(II) onto MLP was occurred at the pH of 6.0, adsorbent dose of 10.0 g/L, and contact time of 60 min, respectively. The adsorption process of Cu(II) onto LP and MLP were described well by both Langmuir and Freundlich isotherms, and the adsorption kinetics of Cu(II) on MLP was pseudo-second-order. Cu(II) adsorption onto LP and MLP are both exothermic, while it is spontaneous for MLP, and non-spontaneous for LP. The maximum adsorption capacity of Cu(II) onto MLP was 23.70 mg/g, which was about 2.7 times higher than that of LP. Additionally, as compared to LP, the leaching amounts of TOC, TN, and TP from MLP were significantly reduced by a percentage of 27.0%, 90.3%, and 35.3%, respectively. PMID:24473344

  2. Synthesized magnetic nanoparticles coated zeolite for the adsorption of pharmaceutical compounds from aqueous solution using batch and column studies.

    PubMed

    Salem Attia, Tamer Mohamed; Hu, Xia Lin; Yin, Da Qiang

    2013-11-01

    The contamination of fresh water with pharmaceutical and personal care products (PPCPs) has risen during the last few years. The adsorption of some PPCPs namely, Diclofenac-Na, Naproxen, Gemfibrozil and Ibuprofen from aqueous solution has been studied, magnetic nanoparticles coated zeolite (MNCZ) has been used as the adsorbent. Batch adsorption experiment was conducted to study the influences of different adsorption parameters such as contact time, solution pH and PPCPs concentrations in order to optimize the reaction conditions. The removal was favored at low pH values. Thus, as pH turns from acidic to basic conditions these compounds were less efficiently removed. The initial concentration does not appear to exert a noticeable effect on the removal efficiency of the studied PPCPs at low concentrations, but it showed less removal efficiency during high concentration of PPCPs especially for Ibuprofen. The removal of Diclofenac-Na was independent on time, while the contact time was of significant effect on the adsorption of Naproxen, Gemfibrozil and Ibuprofen even though these compounds were removed up to 95% during 10 min using MNCZ. From the isotherm adsorption study, the adsorption of PPCPs studied on MNCZ was best fitted with Freundlich isotherm equation. Pseudo-second order model providing the best fit model with the experimental data. Column adsorption study was conducted to compare the removal efficiency of MNCZ with other processes used at drinking water treatment plants (DWTPs), MNCZ showed high removal efficiency (>99%) than other used processes at DWTPs.

  3. Adsorption kinetics and equilibrium study of nitrogen species onto radiata pine (Pinus radiata) sawdust.

    PubMed

    Harmayani, Kadek D; Faisal Anwar, A H M

    2016-01-01

    Nitrogen species (NH3-N, NO3-N, and NO2-N) are found as one of the major dissolved constituents in wastewater or stormwater runoff. In this research, laboratory experiments were conducted to remove these pollutants from the water environment using radiata pine (Pinus radiata) sawdust. A series of batch tests was conducted by varying initial concentration, dosage, particle size, pH, and contact time to check the removal performance. Test results confirmed the effectiveness of radiata pine sawdust for removing these contaminants from the aqueous phase (100% removal of NO3-N, and NO2-N; 55% removal of NH3-N). The adsorbent dosage and initial concentration showed a significantly greater effect on the removal process over pH or particle sizes. The optimum dosage for contaminant removal on a laboratory scale was found to be 12 g. Next, the adsorption kinetics were studied using intraparticle diffusion, liquid-film diffusion, and a pseudo-first order and pseudo-second order model. The adsorption of all species followed a pseudo-second order model but NO2-N adsorption followed both models. In addition, the kinetics of NO2-N adsorption showed two-step adsorption following intraparticle diffusion and liquid-film diffusion. The isotherm study showed that NO3-N and NO2-N adsorption fitted slightly better with the Freundlich model but that NH3-N adsorption followed both Freundlich and Langmuir models. PMID:27438245

  4. Studies of adsorption equilibria and kinetics in the systems: Aqueous solution of dyes-mesoporous carbons

    NASA Astrophysics Data System (ADS)

    Derylo-Marczewska, A.; Marczewski, A. W.; Winter, Sz.; Sternik, D.

    2010-06-01

    Two carbonaceous materials were synthesized by using the method of impregnation of mesoporous silicas obtained by applying the Pluronic copolymers as pore-creating agents. The isotherms of adsorption of methylene blue and methyl orange from aqueous solutions were measured by the static method. The profiles of adsorbate concentration change in time were obtained from the UV-vis spectra. The adsorption isotherms and kinetic dependence were discussed in the terms of theory of adsorption on heterogeneous surfaces.

  5. [Study on the co-adsorption mechanism of Pb (II) and chlorpyrifos on arid loess in northwestern China].

    PubMed

    Fan, Chun-Hui; Zhang, Ying-Chao; Wang, Jia-Hong

    2013-08-01

    The co-adsorption characteristics of Pb(II) and chlorpyrifos on arid loess were investigated with batch adsorption procedures, and the co-adsorption mechanism was studied with approaches of SEM, FT-IR, XRD and theoretical analysis. The experimental results indicated that the adsorption process of Pb(II) and chlorpyrifos on loess fit better the Langmuir isotherm, the maximum adsorption capacity of q(m) is 12.5 and 0.64 mg x g(-1) for Pb(II) and chlorpyrifos on loess, respectively, and the reaction could be illustrated with pseudo-second order kinetic equation. The SEM micrograph of loess surface varies little after the adsorption process of Pb(II) and chlorpyrifos, and certain wave peaks of FTIR spectra red-shift, disappears or intensity-decrease, with the XRD pattern and theoretical analysis, the adsorption mechanism is described as follows: the adsorption of Pb (II) on arid loess is the chemical-effect of coordination-complexation and Van der Waals force; the physical-adsorption on chlorpyrifos involves the interception function, hydrogen bonds and Van der Waals force, and chemical adsorption effect to some extent. The organic matter in arid loess plays an important role in Pb(II) and chlorpyrifos adsorption.

  6. Experimental study of highly turbulent isothermal opposed-jet flows

    NASA Astrophysics Data System (ADS)

    Coppola, Gianfilippo; Gomez, Alessandro

    2010-10-01

    Opposed-jet flows have been shown to provide a valuable means to study a variety of combustion problems, but have been limited to either laminar or modestly turbulent conditions. With the ultimate goal of developing a burner for laboratory flames reaching turbulence regimes of relevance to practical systems, we characterized highly turbulent, strained, isothermal, opposed-jet flows using particle image velocimetry (PIV). The bulk strain rate was kept at 1250 s-1 and specially designed and properly positioned turbulence generation plates in the incoming streams boosted the turbulence intensity to well above 20%, under conditions that are amenable to flame stabilization. The data were analyzed with proper orthogonal decomposition (POD) and a novel statistical analysis conditioned to the instantaneous position of the stagnation surface. Both POD and the conditional analysis were found to be valuable tools allowing for the separation of the truly turbulent fluctuations from potential artifacts introduced by relatively low-frequency, large-scale instabilities that would otherwise partly mask the turbulence. These instabilities cause the stagnation surface to wobble with both an axial oscillation and a precession motion about the system axis of symmetry. Once these artifacts are removed, the longitudinal integral length scales are found to decrease as one approaches the stagnation line, as a consequence of the strained flow field, with the corresponding outer scale turbulent Reynolds number following a similar trend. The Taylor scale Reynolds number is found to be roughly constant throughout the flow field at about 200, with a value virtually independent of the data analysis technique. The novel conditional statistics allowed for the identification of highly convoluted stagnation lines and, in some cases, of strong three-dimensional effects, that can be screened, as they typically yield more than one stagnation line in the flow field. The ability to lock on the

  7. Adsorption studies of the gram-negative bacteria onto nanostructured silicon carbide.

    PubMed

    Borkowski, Andrzej; Szala, Mateusz; Cłapa, Tomasz

    2015-02-01

    In this study, we demonstrated a significant adsorption of Pseudomonas putida bacteria onto aggregates of nanofibers (NFSiC) and nanorods (NRSiC) of silicon carbide (SiC) in aqueous suspensions. Langmuir and Freundlich isotherms were used to quantify adsorption affinities. It was found that adsorption of the bacteria strongly depended on the structure of the silicon carbide and the pH of the aqueous solution, which affected the isoelectric point of both the silicon carbide and the bacterial cells. The strongest affinity of bacteria was noted in the case of NRSiC aggregates. Affinity was inversely proportional to pH. Similarly, the adsorption of bacteria to the surface of the aggregates increased with decreasing pH. For NFSiC, the affinity of the bacteria for the surface of the aggregates was also inversely proportional to pH. However, adsorption increased at higher pH values. This discrepancy was explained by microscopic analysis, which showed that the bacterial cells were both adsorbed onto and trapped by NFSiC. The adsorption of bacteria onto a micrometric silicon carbide reference material was significantly smaller than adsorption onto nanostructured SiC.

  8. Adsorption studies of methylene blue and phenol onto vetiver roots activated carbon prepared by chemical activation.

    PubMed

    Altenor, Sandro; Carene, Betty; Emmanuel, Evens; Lambert, Jacques; Ehrhardt, Jean-Jacques; Gaspard, Sarra

    2009-06-15

    Vetiver roots have been utilized for the preparation of activated carbon (AC) by chemical activation with different impregnation ratios of phosphoric acid, X(P) (gH(3)PO(4)/g precursor): 0.5:1; 1:1 and 1.5:1. Textural characterization, determined by nitrogen adsorption at 77K shows that mixed microporous and mesoporous structures activated carbons (ACs) with high surface area (>1000 m(2)/g) and high pore volume (up to 1.19 cm(3)/g) can be obtained. The surface chemical properties of these ACs were investigated by X-ray photoelectron spectroscopy (XPS) and Boehm titration. Their textural and chemical characteristics were compared to those of an AC sample obtained by steam activation of vetiver roots. Classical molecules used for characterizing liquid phase adsorption, phenol and methylene blue (MB), were used. Adsorption kinetics of MB and phenol have been studied using commonly used kinetic models, i.e., the pseudo-first-order model, the pseudo-second-order model, the intraparticle diffusion model and as well the fractal, BWS (Brouers, Weron and Sotolongo) kinetic equation. The correlation coefficients (R(2)) and the normalized standard deviation Deltaq (%) were determined showing globally, that the recently derived fractal kinetic equation could best describe the adsorption kinetics for the adsorbates tested here, indicating a complex adsorption mechanism. The experimental adsorption isotherms of these molecules on the activated carbon were as well analysed using four isotherms: the classical Freundlich, Langmuir, Redlich-Peterson equations, but as well the newly published deformed Weibull Brouers-Sotolongo isotherm. The results obtained from the application of the equations show that the best fits were achieved with the Brouers-Sotolongo equation and with the Redlich-Peterson equation. Influence of surface functional groups towards MB adsorption is as well studied using various ACs prepared from vetiver roots and sugar cane bagasse. Opposite effects governing MB

  9. Adsorptive removal of cadmium by natural red earth: equilibrium and kinetic studies.

    PubMed

    Mahatantila, Kushani; Vithanage, Meththika; Seike, Yasushi; Okumura, Minoru

    2012-01-01

    Natural red earth (NRE), an iron-coated sand found in the north western part of Sri Lanka, was used to examine the retention behaviour of cadmium, a heavy metal postulated as a factor of chronic kidney disease in Sri Lanka. Adsorption studies were conducted as a function of pH, ionic strength, initial Cd loading and time. The Cd adsorption increased from 6% to 99% with the pH increase from 4 to 8.5. The maximum adsorption was reached at pH > 7.5. Cadmium adsorption was not changed over 100-fold variations of NaNO3, providing evidence for the dominance of an inner-sphere bonding mechanism for both 10-fold variation of initial Cd concentrations. Surface complexation modelling suggests a monodentate bonding mechanism. Isotherm data were fairly fitted to a two-site Langmuir isotherm model and sorption maximums of 9.11 x 10(-6) and 3.89 x 10(-7) mol g(-1) were obtained for two surface sites. The kinetic study reveals that Cd uptake by NRE is so fast that the equilibrium was reached within 15 min and - 1 h for 4.44 and 44.4 microM initial Cd concentrations, respectively, and the chemisorption was the dominant mechanism over intra-particle diffusion. The study indicates the potential of NRE as a material for decontaminating environmental water polluted with Cd.

  10. Adsorption studies of natural gas storage in Devonian shales

    SciTech Connect

    Lu, X.C.; Li, F.C.; Watson, A.T.

    1995-06-01

    Significant amounts of natural gas exist as an adsorbed, or condensed, phase in Devonian shale formations and other unconventional gas resources. The amount of the adsorbed phase depends on the pressure and temperature. The Langmuir isotherm has been used to describe the pressure dependence. However, temperature dependence has not been explored. This is important to evaluate thermal simulation as a recovery method and to extrapolate laboratory measurements to reservoir conditions. The authors investigate adsorption as a function of both pressure and temperature. They found that the effects of temperature are significant and that the Langmuir model does not describe adsorption adequately. They reconciled the data with bi-Langmuir models.

  11. Studies on adsorption, reaction mechanisms and kinetics for photocatalytic degradation of CHD, a pharmaceutical waste.

    PubMed

    Sarkar, Santanu; Bhattacharjee, Chiranjib; Curcio, Stefano

    2015-11-01

    The photocatalytic degradation of chlorhexidine digluconate (CHD), a disinfectant and topical antiseptic and adsorption of CHD catalyst surface in dark condition has been studied. Moreover, the value of kinetic parameters has been measured and the effect of adsorption on photocatalysis has been investigated here. Substantial removal was observed during the photocatalysis process, whereas 40% removal was possible through the adsorption route on TiO2 surface. The parametric variation has shown that alkaline pH, ambient temperature, low initial substrate concentration, high TiO2 loading were favourable, though at a certain concentration of TiO2 loading, photocatalytic degradation efficiency was found to be maximum. The adsorption study has shown good confirmation with Langmuir isotherm and during the reaction at initial stage, it followed pseudo-first-order reaction, after that Langmuir Hinshelwood model was found to be appropriate in describing the system. The present study also confirmed that there is a significant effect of adsorption on photocatalytic degradation. The possible mechanism for adsorption and photocatalysis has been shown here and process controlling step has been identified. The influences of pH and temperature have been explained with the help of surface charge distribution of reacting particles and thermodynamic point of view respectively.

  12. Adsorption studies of Cu(II) onto biopolymer chitosan and its nanocomposite 5%bentonite/chitosan.

    PubMed

    Moussout, Hamou; Ahlafi, Hammou; Aazza, Mustapha; Zegaoui, Omar; El Akili, Charaf

    2016-01-01

    Chitosan (CS) and nanocomposite 5%bentonite/chitosan (5%Bt/CS) prepared from the natural biopolymer CS were tested to remove Cu(II) ions using a batch adsorption experiment at various temperatures (25, 35 and 45°C). X-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis/differential thermal analysis (TGA/DTA) were used in CS and the nanocomposite characterisation. This confirmed the exfoliation of bentonite (Bt) to form the nanocomposite. The adsorption kinetics of copper on both solids was found to follow a pseudo-second-order law at each studied temperature. The Cu(II) adsorption capacity increased as the temperature increased from 25 to 45°C for nanocomposite adsorbent but slightly increased for CS. The data were confronted to the nonlinear Langmuir, Freundlich and Redlich-Peterson models. It was found that the experimental data fitted very well the Langmuir isotherm over the whole temperature and concentration ranges. The maximum monolayer adsorption capacity for the Cu(II) was 404-422 mg/g for CS and 282-337 mg/g for 5%Bt/CS at 25-45°C. The thermodynamic study showed that the adsorption process was spontaneous and endothermic. The complexation of Cu(II) with NH(2) and C = O groups as active sites was found to be the main mechanism in the adsorption processes. PMID:27148722

  13. Adsorption, kinetic and thermodynamic studies for manganese extraction from aqueous medium using mesoporous silica.

    PubMed

    Idris, Salah Ali Mahgoub

    2015-02-15

    This paper describes studies of functionalized mesoporous silica employed as adsorbent for Mn(II) from aqueous solutions. The surface area of MCM-41 and diethylenetriamine functionalized-MCM-41 used in this study were 760 and 318 m(2) g(-1) (N2 adsorption). A strong dependence on pH in the Mn(II) adsorption capacity and best results were obtained at pH 6.5-7. The adsorption onto the diethylenetriamine functionalized-MCM-41 followed the pseudo-second-order kinetic model and the highest reaction rate 0.324 min(-1) was observed at low initial concentration 10 ppm. The equilibrium data showed excellent correlation with the Langmuir isotherm model and the maximum adsorption capacity of Mn(II) reached 88.9 mg/g for DETA-MCM-41 indicating that the adsorption occurs on a homogeneous surface by monolayer sorption without interaction between the adsorbed ions. These data contribute to the understanding of mechanisms involved in mesoporous silica and provide some practical clues to improve the adsorption efficiency (uptake capacity and kinetics) of Mn(II) ions.

  14. Study of surfactant adsorption on colloidal particles

    SciTech Connect

    Cummins, P.G.; Staples, E. ); Penfold, J. )

    1990-05-03

    Surface tension and small-angle neutron scattering have been used to study the nature of surfactant adsorption on silica sols. This paper presents results on the characterization of the ludox silica sol and adsorbed layers of hexaethylene glycol monododecyl ether (C{sub 12}E{sub 6}). Preliminary results are presented that demonstrate the presence of a lower consolute boundary for the composite system.

  15. Kinetic and thermodynamic studies of sulforaphane adsorption on macroporous resin.

    PubMed

    Yuanfeng, Wu; Lei, Zhang; Jianwei, Mao; Shiwang, Liu; Jun, Huang; Yuru, You; Lehe, Mei

    2016-08-15

    The adsorption equilibrium, kinetic and thermodynamic of sulforaphane (SF) adsorption onto macroporous resin in aqueous phase were studied. The SP850 resin was screened as the appropriate resin for SF purification. From the equilibrium studies, the Redlich-Peterson model was found to be the best for description of the adsorption behavior of SF onto SP850 resin, followed by the Freundlich model and the Langmuir model. Batch equilibrium experiments demonstrated that, in the examined temperature range, the equilibrium adsorption capacity of SP850 resin decreased with increasing adsorption temperature. Thermodynamics studies indicated that the adsorption of SF was a physical, exothermic, and spontaneous process. The adsorption kinetics revealed that the pseudo-second-order kinetic model was suitable to characterize the kinetics of adsorption of SF onto SP850. Finally, the intra-particle diffusion model demonstrated that SF diffused quickly into macropores, and that diffusion slowed down in the meso- and micropores. PMID:27391585

  16. Process development for removal and recovery of cadmium from wastewater by a low-cost adsorbent: Adsorption rates and equilibrium studies

    SciTech Connect

    Periasamy, K.; Namasivayam, C. . Dept. of Environmental Sciences)

    1994-02-01

    Activated carbon prepared from peanut hulls (PHC), an agricultural waste by-product, has been used for the adsorption of Cd(II) from synthetic wastewater. The adsorption data fit better with the Freundlich adsorption isotherm. The applicability of the Lagergren kinetic model has also been investigated. An almost quantitative removal of 20 mg/L Cd(II) by 0.7 g of PHC/L of aqueous solution was observed in the pH range 3.5--9.5. A comparative study with a commercial granular activated carbon (CAC) showed that the adsorption capacity (K[sub f]) of PHC was 31 times larger than that of CAC.

  17. Thermodynamic Study of Interactions Between ZnO and ZnO Binding Peptides Using Isothermal Titration Calorimetry.

    PubMed

    Limo, Marion J; Perry, Carole C

    2015-06-23

    While material-specific peptide binding sequences have been identified using a combination of combinatorial methods and computational modeling tools, a deep molecular level understanding of the fundamental principles through which these interactions occur and in some instances modify the morphology of inorganic materials is far from being fully realized. Understanding the thermodynamic changes that occur during peptide-inorganic interactions and correlating these to structural modifications of the inorganic materials could be the key to achieving and mastering control over material formation processes. This study is a detailed investigation applying isothermal titration calorimetry (ITC) to directly probe thermodynamic changes that occur during interaction of ZnO binding peptides (ZnO-BPs) and ZnO. The ZnO-BPs used are reported sequences G-12 (GLHVMHKVAPPR), GT-16 (GLHVMHKVAPPR-GGGC), and alanine mutants of G-12 (G-12A6, G-12A11, and G-12A12) whose interaction with ZnO during solution synthesis studies have been extensively investigated. The interactions of the ZnO-BPs with ZnO yielded biphasic isotherms comprising both an endothermic and an exothermic event. Qualitative differences were observed in the isothermal profiles of the different peptides and ZnO particles studied. Measured ΔG values were between -6 and -8.5 kcal/mol, and high adsorption affinity values indicated the occurrence of favorable ZnO-BP-ZnO interactions. ITC has great potential in its use to understand peptide-inorganic interactions, and with continued development, the knowledge gained may be instrumental for simplification of selection processes of organic molecules for the advancement of material synthesis and design.

  18. Removal of metal ions from water using nanohydrogel tragacanth gum-g-polyamidoxime: isotherm and kinetic study.

    PubMed

    Masoumi, Arameh; Ghaemy, Mousa

    2014-08-01

    A new biosorbent was prepared by grafting polyacrylonitrile onto iranian tragacanth gum (ITG), a naturally and abundantly available polysaccharide, and subsequent amidoximation in the presence of hydroxylamine hydrochloride. This nanohydrogel with amidoxime functional groups [C(NH2)NOH], named polyamidoxime-g-tragacanth (ITG-g-PAO), was characterized and used for the removal of metal ions from aqueous solution. The effect of pH, agitation time, concentration of adsorbate and amount of adsorbent on the extent of adsorption was investigated. The experimental data were analyzed by four isotherms and kinetics equations, and the results were fitted well with the Temkin isotherm and pseudo-second-order model. The maximum adsorption capacities (Qm) of ITG-g-PAO as obtained from Langmuir adsorption isotherm were found to be 100.0, 76.92, 71.42 and 66.67 (mgg(-1)) for the adsorption of metal ions in order of Co(II)>Zn(II)>Cr(III)>Cd(II). The experimental results demonstrate that the above selective order of adsorption capacity is due to formation of stable chelating ring between the bidentate amidoxime ligand and metal ion.

  19. Equilibrium, kinetic and thermodynamic studies on the adsorption of the toxins of Bacillus thuringiensis subsp. kurstaki by clay minerals

    NASA Astrophysics Data System (ADS)

    Fu, Qingling; Deng, Yali; Li, Huishu; Liu, Jie; Hu, Hongqing; Chen, Shouwen; Sa, Tongmin

    2009-02-01

    The persistence of Bacillus thuringiensis ( Bt) toxins in soil is further enhanced through association with soil particles. Such persistence may improve the effectiveness of controlling target pests, but impose a hazard to non-target organisms in soil ecosystems. In this study, the equilibrium adsorption of the Bt toxin by four clay minerals (montmorillonite, kaolinite, goethite, and silicon dioxide) was investigated, and the kinetic and thermodynamic parameters were calculated. The results showed that Bt toxin could be adsorbed easily by minerals, and the adsorption was much easier at low temperature than at high temperature at the initial concentration varying from 0 to 1000 mg L -1. The adsorption fitted well to both Langmuir and Freundlich isotherm models, but the Freundlich equation was more suitable. The pseudo-second-order (PSO) was the best application model to describe the adsorption kinetic. The adsorption process appeared to be controlled by chemical process, and the intra-particle diffusion was not the only rate-controlling step. The negative standard free energy ( ΔGmθr) values of the adsorption indicated that the adsorption of the Bt toxin by the minerals was spontaneous, and the changes of the standard enthalpy ( ΔHmθr) showed that the adsorption of the Bt toxin by montmorillonite was endothermic while the adsorption by the other three minerals was exothermic.

  20. Adsorption kinetic and equilibrium study for removal of mercuric chloride by CuCl2-impregnated activated carbon sorbent.

    PubMed

    Li, Xin; Liu, Zhouyang; Lee, Joo-Youp

    2013-05-15

    The intrinsic adsorption kinetics of mercuric chloride (HgCl2) was studied for raw, 4% and 10% CuCl2-impregnated activated carbon (CuCl2-AC) sorbents in a fixed-bed system. An HgCl2 adsorption kinetic model was developed for the AC sorbents by taking into account the adsorption kinetics, equilibrium, and internal and external mass transfer. The adsorption kinetic constants determined from the comparisons between the simulation and experimental results were 0.2, 0.3, and 0.5m(3)/(gs) for DARCO-HG, 4%(wt), and 10%(wt) CuCl2-AC sorbents, respectively, at 140 °C. CuCl2 loading was found to slightly increase the adsorption kinetic constant or at least not to decrease it. The HgCl2 equilibrium adsorption data based on the Langmuir isotherm show that high CuCl2 loading can result in high binding energy of the HgCl2 adsorption onto the carbon surface. The adsorption equilibrium constant was found to increase by ~10 times when CuCl2 loading varied from 0 to 10%(wt), which led to a decrease in the desorption kinetic constant (k2) by ~10 times and subsequently the desorption rate by ~50 times. Intraparticle pore diffusion considered in the model showed good accuracy, allowing for the determination of intrinsic HgCl2 adsorption kinetics.

  1. Parametric and adsorption kinetic studies of methylene blue removal from simulated textile water using durian (Durio zibethinus murray) skin.

    PubMed

    Anisuzzaman, S M; Joseph, Collin G; Krishnaiah, D; Bono, A; Ooi, L C

    2015-01-01

    In this study, durian (Durio zibethinus Murray) skin was examined for its ability to remove methylene blue (MB) dye from simulated textile wastewater. Adsorption equilibrium and kinetics of MB removal from aqueous solutions at different parametric conditions such as different initial concentrations (2-10 mg/L), biosorbent dosages (0.3-0.7 g) and pH solution (4-9) onto durian skin were studied using batch adsorption. The amount of MB adsorbed increased from 3.45 to 17.31 mg/g with the increase in initial concentration of MB dye; whereas biosorbent dosage increased from 1.08 to 2.47 mg/g. Maximum dye adsorption capacity of the durian skin was found to increase from 3.78 to 6.40 mg/g, with increasing solution pH. Equilibrium isotherm data were analyzed according to Langmuir and Freundlich isotherm models. The sorption equilibrium was best described by the Freundlich isotherm model with maximum adsorption capacity of 7.23 mg/g and this was due to the heterogeneous nature of the durian skin surface. Kinetic studies indicated that the sorption of MB dye tended to follow the pseudo second-order kinetic model with promising correlation of 0.9836 < R(2) < 0.9918.

  2. [Simulation study on the effect of salinity on the adsorption behavior of mercury in wastewater-irrigated area].

    PubMed

    Zheng, Shun-An; Li, Xiao-Hua; Xu, Zhi-Yu

    2014-05-01

    This study was designed to pinpoint the impact of salinity ( NaCl and Na2SO4, added at salinity levels of 0-5%, respectively) on the adsorption behavior of mercury in wastewater-irrigated areas of Tianjin City by batch and kinetic experiments. The results showed that, the Langmuir isotherm and the Elovich equation can well fitted batch and kinetic experimental data, respectively. As NaCI spiked in soil, Hg( II) adsorption capacity and strength had marked decreases, from 868.64 mgkg-1 and 1. 32 at control to 357.48 mgkg-1 and 0.63 at 5% salinity level of NaCI, respectively. As Na2SO4 spiked in soil, Hg(II) adsorption capacity (parameter qm in Langmuir isotherm) and strength (parameter k in Langmuir isotherm) changed slightly, from 868.64 mg kg-1 and 1.32 at control to 739.44 mg.kg-1 and 1. 18 at 5% salinity level of Na2 SO4, respectively. Kinetic data showed that, Hg( II) adsorption rate (parameter b in Elovich equation) in soil was not influenced by Na2SO, addition. However, the addition of NaC1 had a great effect on mercury adsorption rate. Hg(II ) adsorption capacity as a function of CI- or SO(2-)(4) content in soil could be simulated by the natural logarithm model, while Hg( II ) adsorption rate as a function of CI- content in soil could be simulated by the linear model. The study manifested that NaCI can significantly increase migration of Hg( II ) in the soil irrigated with wastewater, which may enhance Hg( II) bioavailability in the soil and cause a hazard to surface water. Especially, it will be harmful to human body through the food chain. PMID:25055690

  3. Modeling and Experimental Studies of Mercury Oxidation and Adsorption in a Fixed-Bed Reactor

    SciTech Connect

    Buitrago, Paula A.; Morrill, Mike; Lighty, JoAnn S.; Silcox, Geoffrey D.

    2009-06-15

    This report presents experimental and modeling mercury oxidation and adsorption data. Fixed-bed and single-particle models of mercury adsorption were developed. The experimental data were obtained with two reactors: a 300-W, methane-fired, tubular, quartz-lined reactor for studying homogeneous oxidation reactions and a fixed-bed reactor, also of quartz, for studying heterogeneous reactions. The latter was attached to the exit of the former to provide realistic combustion gases. The fixed-bed reactor contained one gram of coconut-shell carbon and remained at a temperature of 150°C. All methane, air, SO2, and halogen species were introduced through the burner to produce a radical pool representative of real combustion systems. A Tekran 2537A Analyzer coupled with a wet conditioning system provided speciated mercury concentrations. At 150°C and in the absence of HCl or HBr, the mercury uptake was about 20%. The addition of 50 ppm HCl caused complete capture of all elemental and oxidized mercury species. In the absence of halogens, SO2 increased the mercury adsorption efficiency to up to 30 percent. The extent of adsorption decreased with increasing SO2 concentration when halogens were present. Increasing the HCl concentration to 100 ppm lessened the effect of SO2. The fixed-bed model incorporates Langmuir adsorption kinetics and was developed to predict adsorption of elemental mercury and the effect of multiple flue gas components. This model neglects intraparticle diffusional resistances and is only applicable to pulverized carbon sorbents. It roughly describes experimental data from the literature. The current version includes the ability to account for competitive adsorption between mercury, SO2, and NO2. The single particle model simulates in-flight sorbent capture of elemental mercury. This model was developed to include Langmuir and Freundlich isotherms, rate equations, sorbent feed rate, and

  4. Adsorption of phthalic acid and its esters onto high-area activated carbon-cloth studied by in situ UV-spectroscopy.

    PubMed

    Ayranci, Erol; Bayram, Edip

    2005-06-30

    The adsorption behavior of phthalic acid and its three esters dimethyl phthalate, diethyl phthalate and diallyl phthalate onto high-area activated carbon-cloth was studied by in situ UV-spectroscopic technique. The effect of ionization of phthalic acid on its adsorption was examined by carrying out the adsorption process in three media; water, 1 M H(2)SO(4) and 0.005 M NaOH. Maximum adsorption was observed in 1 M H(2)SO(4) and almost no adsorption in 0.005 M NaOH. These results were discussed in terms of electrostatic and dispersion interactions between the adsorbate species and the carbon-cloth surface taking the point of zero charge (pH(pzc)) of the carbon-cloth into account. The adsorption process for the phthalate species studied was found to follow the first-order rate law, and the rate constants were determined. The isotherm data for the adsorption of phthalic acid and its esters were derived experimentally and fitted to Langmuir and Freundlich isotherm equations. Both equations were found to represent the experimental isotherm data almost equally well. PMID:15943937

  5. Adsorption studies of cadmium ions on alginate-calcium carbonate composite beads

    NASA Astrophysics Data System (ADS)

    Mahmood, Zahid; Amin, Athar; Zafar, Uzma; Raza, Muhammad Amir; Hafeez, Irfan; Akram, Adnan

    2015-07-01

    Alginate-calcium carbonate composite material was prepared in the form of beads and characterized using Fourier transform infra red (FT-IR) spectroscopy and scanning electron microscope (SEM) techniques. The adsorption of Cd2+ ions was studied through batch experiments. The adsorption parameters such as contact time (120 min), adsorbent dose (1.5 g), initial metal ion concentration(10 mg/L), pH (6) and agitation speed (150 rpm) were optimized at room temperature. Langmuir and Freundlich isotherms were applied to the data and it was noted that the adsorption of Cd2+ ions is better explained by Freundlich model. The kinetic studies showed that the adsorption of Cd2+ ions followed pseudo-first order kinetics. Thermodynamic parameters like ∆G 0, ∆H 0 and ∆S 0 were calculated and on the basis of these values it was established that the adsorption process is feasible and endothermic in nature. It was concluded from the study that the composite material of alginate and calcium carbonate can effectively be used to recover Cd2+ ions from wastewater.

  6. Adsorption of cesium from aqueous solution using agricultural residue--walnut shell: equilibrium, kinetic and thermodynamic modeling studies.

    PubMed

    Ding, Dahu; Zhao, Yingxin; Yang, Shengjiong; Shi, Wansheng; Zhang, Zhenya; Lei, Zhongfang; Yang, Yingnan

    2013-05-01

    A novel biosorbent derived from agricultural residue - walnut shell (WS) is reported to remove cesium from aqueous solution. Nickel hexacyanoferrate (NiHCF) was incorporated into this biosorbent, serving as a high selectivity trap agent for cesium. Field emission scanning electron microscope (FE-SEM) and thermogravimetric and differential thermal analysis (TG-DTA) were utilized for the evaluation of the developed biosorbent. Determination of kinetic parameters for adsorption was carried out using pseudo first-order, pseudo second-order kinetic models and intra-particle diffusion models. Adsorption equilibrium was examined using Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherms. A satisfactory correlation coefficient and relatively low chi-square analysis parameter χ(2) between the experimental and predicted values of the Freundlich isotherm demonstrate that cesium adsorption by NiHCF-WS is a multilayer chemical adsorption. Thermodynamic studies were conducted under different reaction temperatures and results indicate that cesium adsorption by NiHCF-WS is an endothermic (ΔH° > 0) and spontaneous (ΔG° < 0) process.

  7. A sum-frequency generation spectroscopic study of the Gibbs analysis paradox: monolayer or sub-monolayer adsorption?

    PubMed

    Shahir, Afshin Asadzadeh; Nguyen, Khoi Tan; Nguyen, Anh V

    2016-04-01

    The Gibbs adsorption isotherm (GAI) has been considered as the foundation of surfactant adsorption studies for over a century; however, its application in determining the limiting surface excess has recently been intensively discussed, with contradictory experimental evidence either supporting or refuting the theory. The available arguments are based on monolayer adsorption models. In this paper, we experimentally and intellectually propose and validate the contribution of sub-monolayer adsorption to the GAI paradox. We utilize a powerful intrinsically surface-sensitive technique, vibrational sum-frequency generation spectroscopy (SFG), complementing with conventional tensiometric measurements to address these controversies both quantitatively and qualitatively. Our SFG results revealed that the precipitous decrease in surface tension directly corresponds to surface occupancy by adsorbates. In addition, the Gibbs analysis was successfully applied to the soluble monolayer of a surface-active alcohol to full saturation. However, the full saturation of the topmost monolayer does not necessarily mean that the surface adsorption was completed because the adsorption was observed to continuously occur in the sub-monolayer region soon after the topmost monolayer became saturated. Nonetheless, the Gibbs isotherm failed to account for the excess of alcohol adsorbed in this sub-monolayer region. This new concept of surface excess must therefore be treated thermodynamically.

  8. Kinetics, isothermal and thermodynamics studies of electrocoagulation removal of basic dye rhodamine B from aqueous solution using steel electrodes

    NASA Astrophysics Data System (ADS)

    Adeogun, Abideen Idowu; Balakrishnan, Ramesh Babu

    2015-09-01

    Electrocoagulation was used for the removal of basic dye rhodamine B from aqueous solution, and the process was carried out in a batch electrochemical cell with steel electrodes in monopolar connection. The effects of some important parameters such as current density, pH, temperature and initial dye concentration, on the process, were investigated. Equilibrium was attained after 10 min at 30 °C. Pseudo-first-order, pseudo-second-order, Elovich and Avrami kinetic models were used to test the experimental data in order to elucidate the kinetic adsorption process; pseudo-first-order and Avrami models best fitted the data. Experimental data were analysed using six model equations: Langmuir, Freudlinch, Redlich-Peterson, Temkin, Dubinin-Radushkevich and Sips isotherms and it was found that the data fitted well with Sips isotherm model. The study showed that the process depends on current density, temperature, pH and initial dye concentration. The calculated thermodynamics parameters (Δ G^circ ,Δ H^circ {text{and}}Δ S{^circ } ) indicated that the process is spontaneous and endothermic in nature.

  9. Comparative evaluation of adsorption kinetics of diclofenac and isoproturon by activated carbon.

    PubMed

    Torrellas, Silvia A; Rodriguez, Araceli R; Escudero, Gabriel O; Martín, José María G; Rodriguez, Juan G

    2015-01-01

    Adsorption mechanism of diclofenac and isoproturon onto activated carbon has been proposed using Langmuir and Freundlich isotherms. Adsorption capacity and optimum adsorption isotherms were predicted by nonlinear regression method. Different kinetic equations, pseudo-first-order, pseudo-second-order, intraparticle diffusion model and Bangham kinetic model, were applied to study the adsorption kinetics of emerging contaminants on activated carbon in two aqueous matrices. PMID:26301850

  10. Experimental and Numerical Studies on Isothermal and Non-isothermal Deep Drawing of IS 513 CR3 Steel Sheets

    NASA Astrophysics Data System (ADS)

    Mayavan, T.; Karthikeyan, L.; Senthilkumar, V. S.

    2016-09-01

    The present work aims to investigate the effects of the temperature gradient developed within the tool profiles on the formability of IS 513 CR3-grade steel sheets using the cup drawing test. The deformation characteristics of steel sheets were analyzed by comparing the thicknesses in various regions of the formed cup and also the limiting drawing ratios (LDR). Finite element simulations were carried out to predict the behavior of the steel sheets in isothermal and non-isothermal forming using Abaqus/Standard 6.12-1. An analytical model created by Kim was used to validate the experimental and finite element analysis (FEA) results on identical process parameters. Both the FEA and analytical modeling results showed that formability improvement is possible in warm forming; the findings are in good agreement with the experimental results in determining the locations and values of excessive thinning. The results also indicated that formability improvement cannot be achieved by keeping the tooling temperature at the same level. The LDR increased by around 9.5% in isothermal forming and by 19% in non-isothermal forming (with the punch maintained at a lower temperature compared with the die and blank holder). In addition, the fractured surfaces of unsuccessfully formed samples were analyzed using scanning electron microscopy. Metallographic investigations confirmed that the fracture mechanism during the forming of IS 513 CR3-grade steel sheets depends on the brittleness, strain hardening value, forming temperature, and magnitude of stresses developed.

  11. A GCMC simulation and experimental study of krypton adsorption/desorption hysteresis on a graphite surface.

    PubMed

    Prasetyo, Luisa; Horikawa, Toshihide; Phadungbut, Poomiwat; Johnathan Tan, Shiliang; Do, D D; Nicholson, D

    2016-09-15

    Adsorption isotherms and isosteric heats of krypton on a highly graphitized carbon black, Carbopack F, have been studied with a combination of Monte Carlo simulation and high-resolution experiments at 77K and 87K. Our investigation sheds light on the microscopic origin of the experimentally observed, horizontal hysteresis loop in the first layer, and the vertical hysteresis-loop in the second layer, and is found to be in agreement with our recent Monte Carlo simulation study (Diao et al., 2015). From detailed analysis of the adsorption isotherm, the latter is attributed to the compression of an imperfect solid-like state in the first layer, to form a hexagonally packed, solid-like state, immediately following the first order condensation of the second layer. To ensure that capillary condensation in the confined spaces between microcrystallites of Carbopack F does not interfere with these hysteresis loops, we carried out simulations of krypton adsorption in the confined space of a wedge-shaped pore that mimics the interstices between particles. These simulations show that, up to the third layer, any such interference is negligible.

  12. A GCMC simulation and experimental study of krypton adsorption/desorption hysteresis on a graphite surface.

    PubMed

    Prasetyo, Luisa; Horikawa, Toshihide; Phadungbut, Poomiwat; Johnathan Tan, Shiliang; Do, D D; Nicholson, D

    2016-09-15

    Adsorption isotherms and isosteric heats of krypton on a highly graphitized carbon black, Carbopack F, have been studied with a combination of Monte Carlo simulation and high-resolution experiments at 77K and 87K. Our investigation sheds light on the microscopic origin of the experimentally observed, horizontal hysteresis loop in the first layer, and the vertical hysteresis-loop in the second layer, and is found to be in agreement with our recent Monte Carlo simulation study (Diao et al., 2015). From detailed analysis of the adsorption isotherm, the latter is attributed to the compression of an imperfect solid-like state in the first layer, to form a hexagonally packed, solid-like state, immediately following the first order condensation of the second layer. To ensure that capillary condensation in the confined spaces between microcrystallites of Carbopack F does not interfere with these hysteresis loops, we carried out simulations of krypton adsorption in the confined space of a wedge-shaped pore that mimics the interstices between particles. These simulations show that, up to the third layer, any such interference is negligible. PMID:27343464

  13. Adsorption studies of chromium (VI) removal from water by lanthanum diethanolamine hybrid material.

    PubMed

    Mandal, Sandip; Sahu, Manoj Kumar; Giri, Anil Kumar; Patel, Raj Kishore

    2014-01-01

    In the present research work, lanthanum diethanolamine hybrid material is synthesized by co-precipitation method and used for the removal of Cr(VI) from synthetic dichromate solution and hand pump water sample. The sorption experiments were carried out in batch mode to optimize various influencing parameters such as adsorbent dose, contact time, pH, competitive anions and temperature. The characterization of the material and mechanism of Cr(VI) adsorption on the material was studied by using scanning electron microscope, Fourier transform infrared, X-ray diffraction, Brunauer-Emmett-Teller and thermogravimetric analysis-differential thermal analysis. Adsorption kinetics studies reveal that the adsorption process followed first-order kinetics and intraparticle diffusion model with correlation coefficients (R2) of 0.96 and 0.97, respectively. The adsorption data were best fitted to linearly transformed Langmuir isotherm with correlation coefficient (R2) of 0.997. The maximum removal of Cr(VI) is found to be 99.31% at optimal condition: pH = 5.6 of the solution, adsorbent dose of 8 g L(-1) with initial concentration of 10mgL(-1) of Cr(VI) solution and an equilibrium time of 50 min. The maximum adsorption capacity of the material is 357.1 mg g(-1). Thermodynamic parameters were evaluated to study the effect of temperature on the removal process. The study shows that the adsorption process is feasible and endothermic in nature. The value of E (260.6 kJ mol(-1)) indicates the chemisorption nature of the adsorption process. The material is difficult to be regenerated. The above studies indicate that the hybrid material is capable of removing Cr(VI) from water. PMID:24645464

  14. Adsorption of benzaldehyde at the surface of ice, studied by experimental method and computer simulation.

    PubMed

    Petitjean, Mélanie; Hantal, György; Chauvin, Coline; Mirabel, Philippe; Le Calvé, Stéphane; Hoang, Paul N M; Picaud, Sylvain; Jedlovszky, Pál

    2010-06-15

    Adsorption study of benzaldehyde on ice surfaces is performed by combining experimental and theoretical approaches. The experiments are conducted over the temperature range 233-253 K using a coated wall flow tube coupled to a mass spectrometric detector. Besides the experimental way, the adsorption isotherm is also determined by performing a set of grand canonical Monte Carlo simulations at 233 K. The experimental and calculated adsorption isotherms show a very good agreement within the corresponding errors. Besides, both experimental and theoretical studies permit us to derive the enthalpy of adsorption of benzaldehyde on ice surfaces DeltaH(ads), which are in excellent agreement: DeltaH(ads) = -61.4 +/- 9.7 kJ/mol (experimental) and DeltaH(ads) = -59.4 +/- 5.1 kJ/mol (simulation). The obtained results indicate a much stronger ability of benzaldehyde of being adsorbed at the surface of ice than that of small aliphatic aldehydes, such as formaldehyde or acetaldehyde. At low surface coverages the adsorbed molecules exclusively lie parallel with the ice surface. With increasing surface coverage, however, the increasing competition of the adsorbed molecules for the surface area to be occupied leads to the appearance of two different perpendicular orientations relative to the surface. In the first orientation, the benzaldehyde molecule turns its aldehyde group toward the ice phase, and, similarly to the molecules in the lying orientation, forms a hydrogen bond with a surface water molecule. In the other perpendicular orientation the aldehyde group turns to the vapor phase, and its O atom interacts with the delocalized pi system of the benzene ring of a nearby lying benzaldehyde molecule of the second molecular layer. In accordance with this observed scenario, the saturated adsorption layer, being stable in a roughly 1 kJ/mol broad range of chemical potentials, contains, besides the first molecular layer, also traces of the second molecular layer of adsorbed

  15. Ab initio study of hydrogen adsorption in MOF-5.

    PubMed

    Sillar, Kaido; Hofmann, Alexander; Sauer, Joachim

    2009-03-25

    Metal-organic frameworks (MOFs) are promising adsorbents for hydrogen storage. Density functional theory and second-order Møller-Plesset perturbation theory (MP2) are used to calculate the interaction energies between H(2) and individual structural elements of the MOF-5 framework. The strongest interaction, DeltaH(77) = -7.1 kJ/mol, is found for the alpha-site of the OZn(4)(O(2)Ph)(6) nodes. We show that dispersion interactions and zero-point vibrational energies must be taken into account. Comparison of calculations done under periodic boundary conditions for the complete structure with those done for finite models cut from the MOF-5 framework shows that the interactions with H(2) originate mainly from the local environment around the adsorption site. When used within a Multi-Langmuir model, the MP2 results reproduce measured adsorption isotherms (the predicted amount is 6 wt % at 77 K and 40 bar) if we assume that the H(2) molecules preserve their rotational degrees of freedom in the adsorbed state. This allows to discriminate between different isotherms measured for different MOF-5 samples and to reliably predict isotherms for new MOF structures. PMID:19253977

  16. Modeling studies: Adsorption of aniline blue by using Prosopis Juliflora carbon/Ca/alginate polymer composite beads.

    PubMed

    Kumar, M; Tamilarasan, R

    2013-02-15

    The research article describes the experimental and modeling study for the adsorptive removal of aniline blue dye (AB dye) from aqueous matrices using a Prosopis Juliflora modified carbon/Ca/alginate polymer bead as a low cost and eco-friendly adsorbent. The rate of adsorption was investigated under various experimental parameters such as contact time, adsorbent dose, dye concentration, pH and temperature. The kinetics, equilibrium and thermodynamic studies were assessed to find out the efficiency of the adsorption process. The equilibrium uptake capacity of the adsorption process was found with Freundlich and Langmuir adsorption isotherm equations and it was evaluated by dimensionless separation factor (R(L)). The dynamics of adsorption was predicted by pseudo-first order, pseudo-second order Lagergren's equation and intra particle diffusion model. Adsorption feasibility was assessed with thermodynamic parameters such as isosteric heat of adsorption (ΔH°), standard entropy (ΔS°) and Gibbs free energy (ΔG°) using VantHoff plot. The alginate bead was characterized with FTIR spectroscopy and Scanning Electron Microscopy (SEM).

  17. Facile approach to synthesize chitosan based composite--Characterization and cadmium(II) ion adsorption studies.

    PubMed

    Pandey, Sadanand; Tiwari, Stuti

    2015-12-10

    In this present study, the physicochemical properties, nature and morphology of prepared composite materials involving Activated Eskom fly ash (A-FA) and biopolymer-chitosan (Ch) for two components composite materials were investigated. The nature, morphology, elemental characterizations of these materials were carried out by means of modern analytical methods such as scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray fluorescence (XRF), UV-vis spectroscopy (UV-vis), and Fourier transform infrared spectroscopy (FTIR. Other physicochemical characterizations undertaken were carbon, nitrogen and hydrogen (CNH) analysis, and ash content. The precursors and composite materials were then applied to the sorption of cadmium (Cd(2+)) from aqueous water. Maximum Cd(2+) adsorption capacity (Qmax) was recorded to be 87.72 mg/g at pH 8. The adsorption kinetics of the composite materials fitted well with the pseudo second-order kinetic model while the adsorption isotherm data could be well described by the Langmuir isotherm model.

  18. Adsorption studies of etherdiamine onto modified sugarcane bagasses in aqueous solution.

    PubMed

    Gusmão, Karla Aparecida Guimarães; Gurgel, Leandro Vinícius Alves; Melo, Tânia Márcia Sacramento; Carvalho, Cornélio de Freitas; Gil, Laurent Frédéric

    2014-01-15

    In this study sugarcane bagasse was modified with succinic anhydride and EDTA dianhydride to obtain SCB 2 and EB adsorbents, respectively. These adsorbents were used to remove etherdiamine, which is used for iron ore flotation from single aqueous solutions. The removal and recovery of etherdiamine is important for environmental and economic reasons due to its toxicity and high cost. The results demonstrated that adsorption of etherdiamine by SCB 2 and EB was better fitted by a pseudo-second-order kinetic model than pseudo-first-order and Elovich models. Adsorption isotherms were better fitted by the Langmuir model rather than the Freundlich, Sips, and Temkin models. The maximum adsorption capacities (Qmax) of SCB 2 and EB for etherdiamine adsorption were found to be 869.6 and 1203.5 mg/g, respectively. The calculated ΔG° values for adsorption of etherdiamine on SCB 2 (-22.70 kJ/mol) and EB (-19.10 kJ/mol) suggested that chemisorption is the main mechanism by which etherdiamine is removed from the aqueous solution for both adsorbents. The high Qmax values showed that SCB 2 and EB are potential adsorbents for recovering the etherdiamine and treating effluents produced from iron ore flotation.

  19. Adsorption Properties of Tetracycline onto Graphene Oxide: Equilibrium, Kinetic and Thermodynamic Studies

    PubMed Central

    Ghadim, Ehsan Ezzatpour; Manouchehri, Firouzeh; Soleimani, Gholamreza; Hosseini, Hadi; Kimiagar, Salimeh; Nafisi, Shohreh

    2013-01-01

    Graphene oxide (GO) nanoparticle is a high potential effective absorbent. Tetracycline (TC) is a broad-spectrum antibiotic produced, indicated for use against many bacterial infections. In the present research, a systematic study of the adsorption and release process of tetracycline on GO was performed by varying pH, sorption time and temperature. The results of our studies showed that tetracycline strongly loads on the GO surface via π–π interaction and cation–π bonding. Investigation of TC adsorption kinetics showed that the equilibrium was reached within 15 min following the pseudo-second-order model with observed rate constants of k2 = 0.2742–0.5362 g/mg min (at different temperatures). The sorption data has interpreted by the Langmuir model with the maximum adsorption of 323 mg/g (298 K). The mean energy of adsorption was determined 1.83 kJ/mol (298 K) based on the Dubinin–Radushkevich (D–R) adsorption isotherm. Moreover, the thermodynamic parameters such as ΔH°, ΔS° and ΔG° values for the adsorption were estimated which indicated the endothermic and spontaneous nature of the sorption process. The electrochemistry approved an ideal reaction for the adsorption under electrodic process. Simulation of GO and TC was done by LAMMPS. Force studies in z direction showed that tetracycline comes close to GO sheet by C8 direction. Then it goes far and turns and again comes close from amine group to the GO sheet. PMID:24302989

  20. Adsorption of Cd, Cu and Zn from aqueous solutions onto ferronickel slag under different potentially toxic metal combination.

    PubMed

    Park, Jong-Hwan; Kim, Seong-Heon; Kang, Se-Won; Kang, Byung-Hwa; Cho, Ju-Sik; Heo, Jong-Soo; Delaune, Ronald D; Ok, Yong Sik; Seo, Dong-Cheol

    2016-01-01

    Adsorption characteristics of potentially toxic metals in single- and multi-metal forms onto ferronickel slag were evaluated. Competitive sorption of metals by ferronickel slag has never been reported previously. The maximum adsorption capacities of toxic metals on ferronickel were in the order of Cd (10.2 mg g(-1)) > Cu (8.4 mg g(-1)) > Zn (4.4 mg g(-1)) in the single-metal adsorption isotherm and Cu (6.1 mg g(-1)) > Cd (2.3 mg g(-1)) > Zn (0.3 mg g(-1)) in the multi-metal adsorption isotherm. In comparison with single-metal adsorption isotherm, the reduction rates of maximum toxic metal adsorption capacity in the multi-metal adsorption isotherm were in the following order of Zn (93%) > Cd (78%) > Cu (27%). The Freundlich isotherm provides a slightly better fit than the Langmuir isotherm equation using ferronickel slag for potentially toxic metal adsorption. Multi-metal adsorption behaviors differed from single-metal adsorption due to competition, based on data obtained from Freundlich and Langmuir adsorption models and three-dimensional simulation. Especially, Cd and Zn were easily exchanged and substituted by Cu during multi-metal adsorption. Further competitive adsorption studies are necessary in order to accurately estimate adsorption capacity of ferronickel slag for potentially toxic metals in natural environments. PMID:26942519

  1. Adsorption of Cd, Cu and Zn from aqueous solutions onto ferronickel slag under different potentially toxic metal combination.

    PubMed

    Park, Jong-Hwan; Kim, Seong-Heon; Kang, Se-Won; Kang, Byung-Hwa; Cho, Ju-Sik; Heo, Jong-Soo; Delaune, Ronald D; Ok, Yong Sik; Seo, Dong-Cheol

    2016-01-01

    Adsorption characteristics of potentially toxic metals in single- and multi-metal forms onto ferronickel slag were evaluated. Competitive sorption of metals by ferronickel slag has never been reported previously. The maximum adsorption capacities of toxic metals on ferronickel were in the order of Cd (10.2 mg g(-1)) > Cu (8.4 mg g(-1)) > Zn (4.4 mg g(-1)) in the single-metal adsorption isotherm and Cu (6.1 mg g(-1)) > Cd (2.3 mg g(-1)) > Zn (0.3 mg g(-1)) in the multi-metal adsorption isotherm. In comparison with single-metal adsorption isotherm, the reduction rates of maximum toxic metal adsorption capacity in the multi-metal adsorption isotherm were in the following order of Zn (93%) > Cd (78%) > Cu (27%). The Freundlich isotherm provides a slightly better fit than the Langmuir isotherm equation using ferronickel slag for potentially toxic metal adsorption. Multi-metal adsorption behaviors differed from single-metal adsorption due to competition, based on data obtained from Freundlich and Langmuir adsorption models and three-dimensional simulation. Especially, Cd and Zn were easily exchanged and substituted by Cu during multi-metal adsorption. Further competitive adsorption studies are necessary in order to accurately estimate adsorption capacity of ferronickel slag for potentially toxic metals in natural environments.

  2. A multi-scale study of the adsorption of lanthanum on the (110) surface of tungsten

    NASA Astrophysics Data System (ADS)

    Samin, Adib J.; Zhang, Jinsuo

    2016-07-01

    In this study, we utilize a multi-scale approach to studying lanthanum adsorption on the (110) plane of tungsten. The energy of the system is described from density functional theory calculations within the framework of the cluster expansion method. It is found that including two-body figures up to the sixth nearest neighbor yielded a reasonable agreement with density functional theory calculations as evidenced by the reported cross validation score. The results indicate that the interaction between the adsorbate atoms in the adlayer is important and cannot be ignored. The parameterized cluster expansion expression is used in a lattice gas Monte Carlo simulation in the grand canonical ensemble at 773 K and the adsorption isotherm is recorded. Implications of the obtained results for the pyroprocessing application are discussed.

  3. Kinetic and isotherm analyses for thorium (IV) adsorptive removal from aqueous solutions by modified magnetite nanoparticle using response surface methodology (RSM)

    NASA Astrophysics Data System (ADS)

    Karimi, Mohammad; Milani, Saeid Alamdar; Abolgashemi, Hossein

    2016-10-01

    In this study, the ability and the adsorption capacity of magnetite/aminopropyltriethoxysilane/glutaraldehyde (Fe3O4/APTES/GA) adsorbent were evaluated for the adsorption of thorium (IV) ions from aqueous solutions. The influence of the several variables such as pH (1-5), Th (IV) initial concentration (50-300 mg L-1) and adsorbent concentration (1-5 g L-1) on the Th (IV) adsorption were investigated by response surface methodology (RSM). The results showed that the highest absorption capacity (q) was 107.23 mg g-1 with respect to pH = 4.5, initial concentration of 250 mg L-1 and adsorbent concentration of 1 g L-1 for 90 min. Modeling equilibrium sorption data with the Langmuir, Freundlich and Dubinin-Radushkevich models pointed out that the results were in good agreement with Langmuir model. The experimental kinetic data were well fitted to pseudo-second-order equation with R2 = 0.9739. Also thermodynamic parameters (ΔGo, ΔHo, ΔSo) declared that the Th (IV) adsorption was endothermic and spontaneous.

  4. Adsorption of methylene blue onto bamboo-based activated carbon: kinetics and equilibrium studies.

    PubMed

    Hameed, B H; Din, A T M; Ahmad, A L

    2007-03-22

    Bamboo, an abundant and inexpensive natural resource in Malaysia was used to prepare activated carbon by physiochemical activation with potassium hydroxide (KOH) and carbon dioxide (CO(2)) as the activating agents at 850 degrees C for 2h. The adsorption equilibrium and kinetics of methylene blue dye on such carbon were then examined at 30 degrees C. Adsorption isotherm of the methylene blue (MB) on the activated carbon was determined and correlated with common isotherm equations. The equilibrium data for methylene blue adsorption well fitted to the Langmuir equation, with maximum monolayer adsorption capacity of 454.2mg/g. Two simplified kinetic models including pseudo-first-order and pseudo-second-order equation were selected to follow the adsorption processes. The adsorption of methylene blue could be best described by the pseudo-second-order equation. The kinetic parameters of this best-fit model were calculated and discussed.

  5. Adsorption studies of methylene blue and gentian violet on sugarcane bagasse modified with EDTA dianhydride (EDTAD) in aqueous solutions: kinetic and equilibrium aspects.

    PubMed

    Gusmão, Karla Aparecida Guimarães; Gurgel, Leandro Vinícius Alves; Melo, Tânia Márcia Sacramento; Gil, Laurent Frédéric

    2013-03-30

    In this study the adsorption of cationic dyes by modified sugarcane bagasse with EDTA dianhydride (EB) was examined using methylene blue (MB) and gentian violet (GV) as model compounds in aqueous single solutions. The synthesized adsorbent (EB) was characterized by FTIR, elemental analysis, and BET. The capacity of EB to adsorb dyes was evaluated at different contact times, pH values, and initial dye concentrations. According to the obtained results, the adsorption processes could be described by a pseudo-second-order kinetic model. The adsorption isotherms were well fitted by the Langmuir model. Maximum adsorption capacities for MB and GV on EB were found to be 202.43 and 327.83 mg/g, respectively. The free energy change during adsorption of MB and GV was found to be -22.50 and -24.21 kJ/mol, respectively, suggesting that chemisorption is the main mechanism controlling the adsorption process.

  6. Adsorption of Ar on planar surfaces studied with a density functional theory.

    PubMed

    Sartarelli, Salvador A; Szybisz, Leszek

    2009-11-01

    The adsorption of Ar on planar structureless substrates of alkali metals, alkaline-earth metal Mg, CO2 , and Au was analyzed by applying a density functional formalism which includes a recently proposed effective attractive pair potential conditioned to Ar. It is shown that this approach reproduces the experimental surface tension of the liquid-vapor interface over the entire bulk coexistence curve for temperatures T spanning from the triple point Tt up to the critical point Tc. The wetting properties were studied over the entire range temperatures Tt<-->Tc. It was found that Ar wets all the investigated surfaces. The adsorption isotherms for alkali metals exhibit first-order phase transitions. Prewetting lines were resolved even for the less attractive surfaces. In the cases of Mg, CO2 , and Au a continuous growth for T> or =Tt was obtained. A comparison with experimental data and other microscopic calculations is reported.

  7. Adsorption of methylene blue onto jute fiber carbon: kinetics and equilibrium studies.

    PubMed

    Senthilkumaar, S; Varadarajan, P R; Porkodi, K; Subbhuraam, C V

    2005-04-01

    Jute fiber obtained from the stem of a plant was used to prepare activated carbon using phosphoric acid. Feasibility of employing this jute fiber activated carbon (JFC) for the removal of Methylene blue (MB) from aqueous solution was investigated. The adsorption of MB on JFC has found to dependent on contact time, MB concentration and pH. Experimental result follows Langmuir isotherm model and the capacity was found to be 225.64 mg/g. The optimum pH for the MB removal was found to be 5-10. The kinetic data obtained at different concentrations have been analyzed using a pseudo-first-order, pseudo-second-order equation, intraparticle diffusion and Elovich equation. Among the kinetic models studied, the intraparticle diffusion was the best applicable model to describe the adsorption of MB onto JFC.

  8. A cluster-exact approximation study of the adsorption of binary mixtures on heterogeneous surfaces

    NASA Astrophysics Data System (ADS)

    Sanchez Varretti, F. O.; Bulnes, F. M.; Ramirez-Pastor, A. J.

    2016-11-01

    The adsorption of binary mixtures on heterogeneous surfaces is studied by a cluster approximation (CA), based on the exact calculation of configurations on finite cells. The substrate is characterized by n types of sites, each with different adsorption energy. The process is monitored through the total and partial isotherms. The theoretical formalism is used to model experimental data of methane-ethane mixtures adsorbed on a template-synthesized carbon. The CA results are compared with the ones corresponding to the well-known Ideal Adsorbed Solution Theory (IAST). Even though a good fitting is obtained from IAST, it is found that CA is a more accurate model to estimate the binary data on the highly heterogeneous carbon sample.

  9. Surfactant-modified montmorillonite as a nanosized adsorbent for removal of an insecticide: kinetic and isotherm studies.

    PubMed

    Hassani, Aydin; Khataee, Alireza; Karaca, Semra; Shirzad-Siboni, Mehdi

    2015-01-01

    Surfactant-modified montmorillonites (MMT) were prepared using trimethyloctylammonium bromide (TMOAB) and employed as a nanosized adsorbent to remove diazinon from aqueous solutions. The prepared adsorbent was characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). The dependence of removal efficiency on initial diazinon concentration, amount of adsorbent, pH of the solution and ionic strength was investigated. The affinity sequence for ion adsorption on TMOAB/MMT was in the order: without anion> sodium carbonate> sodium bicarbonate> sodium sulphate> sodium chloride. The adsorption kinetic and isotherm were best fit by a pseudo-second-order kinetic and Langmuir isotherm models, respectively. PMID:26006742

  10. Studies on adsorption of formaldehyde in zirconium phosphate-glyphosates

    NASA Astrophysics Data System (ADS)

    Zhang, Yuejuan; Yi, Jianjun; Xu, Qinghong

    2011-01-01

    In our previous work [22], a kind of layered compound of zirconium phosphate-glyphosate (ZrGP) was synthesized. Its large surface area (445 m 2/g) indicates this compound has possible application in adsorptions. In this paper, adsorption to formaldehyde in ZrGP and mechanisms of the adsorption were studied carefully. Balance time of adsorption (about 6 h) and largest adsorbed amount (7.8%) were found when adsorption temperature was at 40 °C and pH value of adsorption environment was about 3.0. H-bonds were found existing between molecules of formaldehyde and ZrGP, and formaldehyde molecules could exist in ZrGP stably.

  11. Theoretical consideration of the use of a Langmuir adsorption isotherm to describe the effect of light intensity on electron transfer in photosystem II.

    PubMed

    Fragata, Mário; Viruvuru, Venkataramanaiah; Dudekula, Subhan

    2007-03-29

    Electron transport through photosystem II (PSII), measured as oxygen evolution, was investigated in isolated PSII particles and thylakoid membranes irradiated with white light of intensities (I) of 20 to about 4000 micromol of photons/(m2.s). In steady-state conditions, the evolution of oxygen varies with I according to the hyperbolic expression OEth = OEth(max)I/(L1/2 + I) (eq i) where OEth is the theoretical oxygen evolution, OEth(max) is the maximum oxygen evolution, and L1/2 is the light intensity giving OEth(max)/2. In this work, the mathematical derivation of this relationship was performed by using the Langmuir adsorption isotherm and assuming that the photon interaction with the chlorophyll (Chl) in the PSII reaction center is a heterogeneous reaction in which the light is represented as a stream of particles instead of an electromagnetic wave (see discussion in Turro, N. J. Modern Molecular Photochemistry; University Science Books: Mill Valley, CA, 1991). In accordance with this approximation, the Chl molecules (P680) were taken as the adsorption surfaces (or heterogeneous catalysts), and the incident (or exciting) photons as the substrate, or the reagent. Using these notions, we demonstrated that eq i (Langmuir equation) is a reliable interpretation of the photon-P680 interaction and the subsequent electron transfer from the excited state P680, i.e., P680*, to the oxidized pheophytin (Phe), then from Phe- to the primary quinone QA. First, eq i contains specific functional and structural information that is apparent in the definition of OEth(max) as a measure of the maximal number of PSII reaction centers open for photochemistry, and L1/2 as the equilibrium between the electron transfer from Phe- to QA and the formation of reduced Phe in the PSII reaction center by electrons in provenance from P680*. Second, a physiological control mechanism in eq i is proved by the observation that the magnitudes of OEth(max) and L1/2 are affected differently by exogenous

  12. Design of a hybrid advective-diffusive microfluidic system with ellipsometric detection for studying adsorption.

    PubMed

    Wang, Lei; Zhao, Cunlu; Wijnperlé, Daniel; Duits, Michel H G; Mugele, Frieder

    2016-05-01

    Establishing and maintaining concentration gradients that are stable in space and time is critical for applications that require screening the adsorption behavior of organic or inorganic species onto solid surfaces for wide ranges of fluid compositions. In this work, we present a design of a simple and compact microfluidic device based on steady-state diffusion of the analyte, between two control channels where liquid is pumped through. The device generates a near-linear distribution of concentrations. We demonstrate this via experiments with dye solutions and comparison to finite-element numerical simulations. In a subsequent step, the device is combined with total internal reflection ellipsometry to study the adsorption of (cat)ions on silica surfaces from CsCl solutions at variable pH. Such a combined setup permits a fast determination of an adsorption isotherm. The measured optical thickness is compared to calculations from a triple layer model for the ion distribution, where surface complexation reactions of the silica are taken into account. Our results show a clear enhancement of the ion adsorption with increasing pH, which can be well described with reasonable values for the equilibrium constants of the surface reactions. PMID:27375818

  13. Comparative study of adsorption of Pb(II) on native garlic peel and mercerized garlic peel.

    PubMed

    Liu, Wei; Liu, Yifeng; Tao, Yaqi; Yu, Youjie; Jiang, Hongmei; Lian, Hongzhen

    2014-02-01

    A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb(2+) has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g(-1). The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent-adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb(2+) further illustrated that lead was adsorbed on the through chelation between Pb(2+) and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity.

  14. 2, 4 dichlorophenol (2, 4-DCP) sorption from aqueous solution using granular activated carbon and polymeric adsorbents and studies on effect of temperature on activated carbon adsorption.

    PubMed

    Ghatbandhe, A S; Yenkie, M K N

    2008-04-01

    Adsorption equilibrium, kinetics and thermodynamics of 2,4-dichlorophenol (2,4-DCP), one of the most commonly used chlorophenol, onto bituminous coal based Filtrasorb-400 grade granular activated carbon, were studied in aqueous solution in a batch system with respect to temperature. Uptake capacity of activated carbon found to increase with temperature. Langmuir isotherm models were applied to experimental equilibrium data of 2, 4-DCP adsorption and competitive studies with respect to XAD resin were carried out. Equilibrium data fitted very well to the Langmuir equilibrium model. Adsorbent monolayer capacity 'Q0, Langmuir constant 'b' and adsorption rate constant 'k(a)' were evaluated at different temperatures for activated carbon adsorption. This data was then used to calculate the energy of activation of adsorption and also the thermodynamic parameters, namely the free energy of adsorption, deltaG0, enthalpy of adsorption, deltaH0 and the entropy of adsorption deltaS0. The obtained results showed that the monolayer capacity increases with the increase in temperatures. The obtained values of thermodynamic parameters showed that adsorption of 2,4 DCP is an endothermic process. Synthetic resin was not found efficient to adsorb 2,4 DCP compared to activated carbon. The order of adsorption efficiencies of three resins used in the study found as XAD7HP > XAD4 > XAD1180.

  15. Kinetics and isotherm analysis of 2,4-dichlorophenoxyl acetic acid adsorption onto soil components under oxic and anoxic conditions.

    PubMed

    Ololade, Isaac A; Alomaja, Folasade; Oladoja, Nurudeen A; Ololade, Oluwaranti O; Oloye, Femi F

    2015-01-01

    2,4-dichlorophenoxyl acetic acid (2,4-D, pKa = 2.8) is used extensively as a herbicide in agricultural practices. Its sorption behavior on both untreated and soils treated to significantly remove specific components (organic and iron and manganese [Fe-Mn] oxides and hydroxides phases) was investigated under oxic and anoxic conditions. The chemical and structural heterogeneity of the soil components were characterized by elemental analysis and X-ray diffraction (XRD). The coexistence of the various components seems to either mask sorption sites on the untreated soil surfaces or inhibit interlayer diffusion of 2,4-D. All sorption data conform to the Freundlich description and a pseudo-second-order kinetic model. There was a strong positive correlation between sorption capacity K(d), and surface area (r(2) ≤ 0.704), but a negative correlation was uncovered with both pH and organic carbon (r(2) ≤ -0.860). The results indicate that 2,4-D is preferably sorbed under oxic rather than anoxic conditions and it is greater on soils containing a high Fe content. There was incomplete 2,4-D sorption reversibility, with desorption occurring more rapidly under anoxic conditions. The study suggests that stimulation of Fe III reduction could be used for the bioremediation of a 2,4-D-contaminated site. PMID:25996813

  16. Studies on chelating adsorption properties of novel composite material polyethyleneimine/silica gel for heavy-metal ions

    NASA Astrophysics Data System (ADS)

    Gao, Baojiao; An, Fuqiang; Liu, Kangkai

    2006-12-01

    Firstly, the coordination processes of line-type polyethyleneimine with Cu 2+, Cd 2+ and Zn 2+ were studied by using visible light absorption spectroscopy and chelation conductivity titration method, and the structures of the chelates were determined. Afterwards, polyethyleneimine (PEI) was grafted onto the surface of silica gel particles via the coupling effect of γ-chloropropyl trimethoxysilane (CP), and the novel composite adsorption material PEI/SiO 2 with strong adsorption ability towards heavy-metal ions was prepared. The chelating adsorption properties of PEI/SiO 2 for Cu 2+, Cd 2+ and Zn 2+ were researched by both static (batch) and dynamic (flow) methods. The experiment results show that water-soluble polyamine PEI with line-type structure reacts with Cu 2+, Cd 2+ and Zn 2+ easily and quantitatively, and water-soluble chelates with four ligands are formed. The composite material PEI/SiO 2 possesses very strong chelating adsorption ability for heavy-metal ions, and the saturated adsorption amount can reach 25.94 mg g -1 and 50.01 mg g -1 for Cu 2+ under static and dynamic conditions, respectively. The isothermal adsorption data fit to Langmuir equation, and the adsorption is typical chemical adsorption with monomolecular layer. The adsorbing ability of PEI/SiO 2 towards the three kinds of the ions follows the order of Cu 2+ > Cd 2+ > Zn 2+. The pH value has great influence on the sorption, and at pH 6-7, the adsorption capacity is the greatest. The fact that adsorption capacity increases with temperature rising indicates the adsorbing process of PEI/SiO 2 for metal ions is endothermic. As diluted hydrochloric acid is used as eluent, the adsorbed heavy-metal ions are eluted easily from PEI/SiO 2, and the regeneration and reuse without decreasing sorption for PEI/SiO 2 are demonstrated.

  17. Adsorption studies of aqueous Pb(II) onto a sugarcane bagasse/multi-walled carbon nanotube composite

    NASA Astrophysics Data System (ADS)

    Hamza, Izzeldin A. A.; Martincigh, Bice S.; Ngila, J. Catherine; Nyamori, Vincent O.

    Adsorption of Pb2+ from aqueous solution onto a sugarcane bagasse/multi-walled carbon nanotube (MWCNT) composite was investigated by using a series of batch adsorption experiments and compared with the metal uptake ability of sugarcane bagasse. The efficiency of the adsorption processes was studied experimentally at various pH values, contact times, adsorbent masses, temperatures and initial Pb2+ concentrations. A pH of 4.5 was found to be the optimum pH to obtain a maximum adsorption percentage in 120 min of equilibration time. The composite showed a much enhanced adsorption capacity for Pb2+ of 56.6 mg g-1 compared with 23.8 mg g-1 for bagasse at 28 °C. The Langmuir adsorption isotherm provided the best fit to the equilibrium adsorption data. The pseudo first-order, pseudo second-order, intraparticle diffusion and Elovich kinetics models were used to analyse the rate of lead adsorption and the results show that the Elovich model is more suitable. The thermodynamic parameters of adsorption, namely ΔG°, ΔH° and ΔS°, were determined over the temperature range of 20-45 °C. The adsorption of Pb2+ onto both bagasse and the sugarcane bagasse/MWCNT composite was found to be spontaneous but for the former adsorbent it was enthalpy-driven whereas for the latter it was entropy-driven. Desorption of the lead-loaded adsorbents was fairly efficient with 0.1 mol dm-3 HCl. Overall this composite has the potential to be a good adsorbent for the removal of Pb2+ from wastewaters.

  18. Adsorption of alkenyl succinic anhydride from solutions in carbon tetrachloride on a fine magnetite surface

    NASA Astrophysics Data System (ADS)

    Balmasova, O. V.; Ramazanova, A. G.; Korolev, V. V.

    2016-06-01

    The adsorption of alkenyl succinic anhydride from a solution in carbon tetrachloride on a fine magnetite surface at a temperature of 298.15 K is studied using fine magnetite, which forms the basis of magnetic fluids, as the adsorbent. An adsorption isotherm is recorded and interpreted in terms of the theory of the volume filling of micropores (TVFM). Adsorption process parameters are calculated on the basis of the isotherm. It is shown that at low equilibrium concentrations, the experimental adsorption isotherm is linear in the TVFM equation coordinates.

  19. Kinetic, isotherm and thermodynamic studies of amaranth dye biosorption from aqueous solution onto water hyacinth leaves.

    PubMed

    Guerrero-Coronilla, Imelda; Morales-Barrera, Liliana; Cristiani-Urbina, Eliseo

    2015-04-01

    The present study explored the kinetics, equilibrium and thermodynamics of amaranth (acid red 27) anionic dye (AD) biosorption to water hyacinth leaves (LEC). The effect of LEC particle size, contact time, solution pH, initial AD concentration and temperature on AD biosorption was studied in batch experiments. AD biosorption increased with rising contact time and initial AD concentration, and with decreasing LEC particle size and solution pH. Pseudo-second-order chemical reaction kinetics provided the best correlation for the experimental data. Isotherm studies showed that the biosorption of AD onto LEC closely follows the Langmuir isotherm, with a maximum biosorption capacity of about 70 mg g(-1). The thermodynamic parameters confirm that AD biosorption by LEC is non-spontaneous and endothermic in nature. Results indicate that LEC is a strong biosorbent capable of effective detoxification of AD-laden wastewaters.

  20. ADSORPTION OF POLYCYCLIC AROMATIC HYDROCARBONS IN AGED HARBOR SEDIMENTS

    EPA Science Inventory

    Polycyclic aromatic hydrocarbons (PAHs) are a group of hydrophobic organic contaminants which have low aqueous solubilities and are common pollutants in harbor sediments. Adsorption and desorption isotherms for PAHs are conducted to study the abiotic sorption of PAHs in uncontami...

  1. Functionalized mesoporous silica materials for molsidomine adsorption: Thermodynamic study

    SciTech Connect

    Alyoshina, Nonna A.; Parfenyuk, Elena V.

    2013-09-15

    A series of unmodified and organically modified mesoporous silica materials was prepared. The unmodified mesoporous silica was synthesized via sol–gel synthesis in the presence of D-glucose as pore-forming agent. The functionalized by phenyl, aminopropyl and mercaptopropyl groups silica materials were prepared via grafting. The fabricated adsorbent materials were characterized by Fourier transform infrared spectroscopy (FTIR) analysis, N{sub 2} adsorption/desorption and elemental analysis methods. Then their adsorption properties for mesoionic dug molsidomine were investigated at 290–313 K and physiological pH value. Thermodynamic parameters of molsidomine adsorption on the synthesized materials have been calculated. The obtained results showed that the adsorption process of molsidomine on the phenyl modified silica is the most quantitatively and energetically favorable. The unmodified and mercaptopropyl modified silica materials exhibit significantly higher adsorption capacities and energies for molsidomine than the aminopropyl modified sample. The effects are discussed from the viewpoint of nature of specific interactions responsible for the adsorption. - Graphical abstract: Comparative analysis of the thermodynamic characteristics of molsidomine adsorption showed that the adsorption process on mesoporous silica materials is controlled by chemical nature of surface functional groups. Molsidomine adsorption on the phenyl modified silica is the most quantitatively and energetically favorable. Taking into account ambiguous nature of mesoionic compounds, it was found that molsidomine is rather aromatic than dipolar. Display Omitted - Highlights: • Unmodified and organically modified mesoporous silica materials were prepared. • Molsidomine adsorption on the silica materials was studied. • Phenyl modified silica shows the highest adsorption capacity and favorable energy. • Molsidomine exhibits the lowest affinity to aminopropyl modified silica.

  2. [Study of adsorption and desorption of behaviors of Pb2+ on thiol-modified bentonite by flame atomic absorption spectrometry].

    PubMed

    Chen, Wen; Xiong, Qiong-Xian; Pang, Xiao-Feng; Zhu, Xia-Ping; Han, Mei; Zhao, Qiu-Xiang; Liu, Wen-Hua

    2013-03-01

    A comparative analysis of the functional groups and surface structure of the Ca-bentonite (RB) and thiol-modified bentonite (TMB) were characterized by means of FTIR and SEM. The absorptive property of Pb2+ on TMB and RB and its influential factors was studied and the conditions for the adsorption were optimized by using FAAS method. Then the conditions for desorption of Pb2+ from the TMB by using simulated acid rain were studied and the contrast analysis of absorptive stability of Pb2+ on TMB and RB was given. The results showed that the adsorption rate of Pb2+ by TMB could reach more than 98%, when the initial Pb2+ concentration was 100 mg.L-1, the liquid-solid ratio was 5 g.L-1, pH was 6. 0, KNO3 ionic strength was 0. 1 mol.L-1 and adsorption period was 60min at 25 C. The saturated adsorption capacity of TMB was 67.27 mg.g-1; it's much more than that of RB (9.667 mg.g-1). The adsorption of Pb2+ on TMB follows Langmuir and Freundlich isotherm models well. Desorption experiments of Pb2+ from TMB with simulated acid rain (pH 3. 50) were done, and the desorption rate was 0. The results showed that TMB has a strong adsorption and fixation capacity for PbZ+; it is adapted to lead contaminated soil for chemical remediation. PMID:23705461

  3. Enhancing adsorption capacity of toxic malachite green dye through chemically modified breadnut peel: equilibrium, thermodynamics, kinetics and regeneration studies.

    PubMed

    Chieng, Hei Ing; Lim, Linda B L; Priyantha, Namal

    2015-01-01

    Breadnut skin, in both its unmodified (KS) and base-modified (BM-KS) forms, was investigated for its potential use as a low-cost adsorbent for the removal of toxic dye, malachite green (MG). Characterization of the adsorbents was carried out using scanning electron microscope, X-ray fluorescence and Fourier transform infra-red spectroscopy. Batch adsorption experiments, carried out under optimized conditions, for the adsorption of MG were fitted using five isotherm models (Langmuir, Freundlich, Dubinin-Radushkevich, Temkin and Sips) and six error functions to determine the best-fit model. The adsorption capacity was greatly enhanced when breadnut skin was chemically modified with NaOH, leading to an adsorption capacity of 353.0 mg g(-1), that was far superior to most reported adsorbents for the removal of MG. Thermodynamics studies indicated that the adsorption of MG was spontaneous on KS and BM-KS, and the reactions were endothermic and exothermic, respectively. Kinetics studies showed that both followed the pseudo-second order. Regeneration experiments on BM-KS indicated that its adsorption capacity was still maintained at>90% even after five cycles. It can be concluded that NaOH-modified breadfruit skin has great potential to be utilized in real-life application as a low-cost adsorbent for the removal of MG in wastewater treatment.

  4. [Study of adsorption and desorption of behaviors of Pb2+ on thiol-modified bentonite by flame atomic absorption spectrometry].

    PubMed

    Chen, Wen; Xiong, Qiong-Xian; Pang, Xiao-Feng; Zhu, Xia-Ping; Han, Mei; Zhao, Qiu-Xiang; Liu, Wen-Hua

    2013-03-01

    A comparative analysis of the functional groups and surface structure of the Ca-bentonite (RB) and thiol-modified bentonite (TMB) were characterized by means of FTIR and SEM. The absorptive property of Pb2+ on TMB and RB and its influential factors was studied and the conditions for the adsorption were optimized by using FAAS method. Then the conditions for desorption of Pb2+ from the TMB by using simulated acid rain were studied and the contrast analysis of absorptive stability of Pb2+ on TMB and RB was given. The results showed that the adsorption rate of Pb2+ by TMB could reach more than 98%, when the initial Pb2+ concentration was 100 mg.L-1, the liquid-solid ratio was 5 g.L-1, pH was 6. 0, KNO3 ionic strength was 0. 1 mol.L-1 and adsorption period was 60min at 25 C. The saturated adsorption capacity of TMB was 67.27 mg.g-1; it's much more than that of RB (9.667 mg.g-1). The adsorption of Pb2+ on TMB follows Langmuir and Freundlich isotherm models well. Desorption experiments of Pb2+ from TMB with simulated acid rain (pH 3. 50) were done, and the desorption rate was 0. The results showed that TMB has a strong adsorption and fixation capacity for PbZ+; it is adapted to lead contaminated soil for chemical remediation.

  5. Enhancing adsorption capacity of toxic malachite green dye through chemically modified breadnut peel: equilibrium, thermodynamics, kinetics and regeneration studies.

    PubMed

    Chieng, Hei Ing; Lim, Linda B L; Priyantha, Namal

    2015-01-01

    Breadnut skin, in both its unmodified (KS) and base-modified (BM-KS) forms, was investigated for its potential use as a low-cost adsorbent for the removal of toxic dye, malachite green (MG). Characterization of the adsorbents was carried out using scanning electron microscope, X-ray fluorescence and Fourier transform infra-red spectroscopy. Batch adsorption experiments, carried out under optimized conditions, for the adsorption of MG were fitted using five isotherm models (Langmuir, Freundlich, Dubinin-Radushkevich, Temkin and Sips) and six error functions to determine the best-fit model. The adsorption capacity was greatly enhanced when breadnut skin was chemically modified with NaOH, leading to an adsorption capacity of 353.0 mg g(-1), that was far superior to most reported adsorbents for the removal of MG. Thermodynamics studies indicated that the adsorption of MG was spontaneous on KS and BM-KS, and the reactions were endothermic and exothermic, respectively. Kinetics studies showed that both followed the pseudo-second order. Regeneration experiments on BM-KS indicated that its adsorption capacity was still maintained at>90% even after five cycles. It can be concluded that NaOH-modified breadfruit skin has great potential to be utilized in real-life application as a low-cost adsorbent for the removal of MG in wastewater treatment. PMID:25409587

  6. Removal of divalent nickel from aqueous solutions using Carissa carandas and Syzygium aromaticum: isothermal studies and kinetic modelling

    NASA Astrophysics Data System (ADS)

    Sharma, Sanjay K.; Mahiya, Suresh; Lofrano, Giusy

    2015-11-01

    Biosorptive removal of divalent nickel from aqueous solution using Carissa Carandas and Syzygium aromaticum was investigated in batch mode and the observations were correlated with the pH variation, agitation time, dose of the adsorbent and initial metal ion concentration in the solution. In the course of this study Sorption efficiency of C. carandas leaf powder found higher than that of S. aromaticum under identical experimental conditions. The maximum adsorption capacities estimated for Ni(II) through Freundlich isotherm model were 3.76 and 2.96 mg/g for C. carandas and S. aromaticum, respectively. In kinetic studies the correlation coefficient (R 2 = 0.99) for the pseudo-second order kinetics modal was higher than that of pseudo-first order kinetics model and the calculated value of q e for the pseudo-second order kinetic model resulted very close to the experimental value, which indicates that it fits well with the equilibrium data for Ni(II) sorption from aqueous solutions on biosorbents.

  7. Adsorption edge study about cadmium, copper, nickel and zinc adsorption by variable charge soils

    NASA Astrophysics Data System (ADS)

    Casagrande, J. C.; Mouta, E. R.; Soares, M. R.

    2009-04-01

    The improper discharge of industrial and urban residues and the inadvertent use of fertilizers and pesticides can result in soil and water pollution and improve the potential of trace metals to enter in the human food chain. Adsorption reactions occur at the solid/liquid interface and are the most important mechanisms for controlling the activity of metal ions in soil solution. In a complex system with amphoteric behavior, the comprehension of the mobility, availability and fate of pollutants in the soil system is crucial for the prediction of the environmental consequences and for development of prevention/remediation strategies. A comparative study of cadmium (Cd), copper (Cu), nickel (Ni) and zinc (Zn) adsorption by highly weathered soils was carried out. Surface (0-0.2m) and subsoil (B horizon) samples were taken from a Rhodic Kandiudalf (RH), an Anionic "Xanthic" Acrudox (XA) and an Anionic "Rhodic" Acrudox (RA), located in brazilian humid tropical area. As the pH and the ionic strength are important environmental factors influencing the solution chemistry of heavy metals in variable charge systems, adsorption envelopes, in a batch adsorption experiment, were elaborated by reacting, for 24 h, soil samples with individual 0.01, 0.1 and 1.0 mol L-1 Ca(NO3)2 aqueous solutions containing nitrate salts of the adsorptive heavy metal (Cd, Cu, Ni and Zn) at the initial concentration of 5 mg L-1, with an increasing pH value from 3.0 to 8.0. pH50-100%, the difference between the pH of 100 and 50 percent metal adsorption was determined. A sharp increase of adsorption density (adsorption edge) was observed within a very narrow pH range, usually less than two pH units. Commonly, the relative affinity of a soil for a metal cation increases with the tendency of the cation to form inner-sphere surface complexes. This may be caused by differences in extent of hydrolysis of Cu ions and in affinity of adsorption sites for Cu. In general, subsurface samples showed low pH50

  8. Competitive adsorption of heavy metals onto sesame straw biochar in aqueous solutions.

    PubMed

    Park, Jong-Hwan; Ok, Yong Sik; Kim, Seong-Heon; Cho, Ju-Sik; Heo, Jong-Soo; Delaune, Ronald D; Seo, Dong-Cheol

    2016-01-01

    Objective of this research was to evaluate adsorption of heavy metals in mono and multimetal forms onto sesame straw biochar (SSB). Competitive sorption of metals by SSB has never been reported previously. The maximum adsorption capacities (mgg(-1)) of metals by SSB were in the order of Pb (102)≫Cd (86)≫Cr (65)>Cu (55)≫Zn (34) in the monometal adsorption isotherm and Pb (88)≫Cu (40)≫Cr (21)>Zn (7)⩾Cd (5) in the multimetal adsorption isotherm. Based on data obtained from the distribution coefficients, Freundlich and Langmuir adsorption models, and three-dimensional simulation, multimetal adsorption behaviors differed from monometal adsorption due to competition. Especially, during multimetal adsorption, Cd was easily exchanged and substituted by other metals. Further competitive adsorption studies are necessary in order to accurately estimate the heavy metal adsorption capacity of biochar in natural environments.

  9. Kinetic Study on the Isothermal and Nonisothermal Crystallization of Monoglyceride Organogels

    PubMed Central

    Meng, Zong; Yang, Lijun; Geng, Wenxin; Yao, Yubo; Wang, Xingguo; Liu, Yuanfa

    2014-01-01

    The isothermal and nonisothermal crystallization kinetics of monoglyceride (MAG) organogels were studied by pulsed nuclear magnetic resonance (pNMR) and differential scanning calorimetry (DSC), respectively. The Avrami equation was used to describe the isothermal crystallization kinetics and experimental data fitted the equation fairly well. Results showed that the crystal growth of MAG organogels was a rod-like growth of instantaneous nuclei at higher degrees of supercooling and a plate-like form with high nucleation rate at lower degrees of supercooling. The exothermic peak in nonisothermal DSC curves for the MAG organogels became wider and shifted to lower temperature when the cooling rate increased, and nonisothermal crystallization was analyzed by Mo equation. Results indicated that at the same crystallization time, to get a higher degree of relative crystallinity, a higher cooling rate was necessary. The activation energy of nonisothermal crystallization was calculated as 739.59 kJ/mol according to the Kissinger method. Therefore, as the results of the isothermal and nonisothermal crystallization kinetics for the MAG organogels obtained, the crystallization rate, crystal nucleation, and growth during the crystallization process could be preliminarily monitored through temperature and cooling rate regulation, which laid the foundation for the real industrial manufacture and application of the MAG organogels. PMID:24701138

  10. Kinetic study on the isothermal and nonisothermal crystallization of monoglyceride organogels.

    PubMed

    Meng, Zong; Yang, Lijun; Geng, Wenxin; Yao, Yubo; Wang, Xingguo; Liu, Yuanfa

    2014-01-01

    The isothermal and nonisothermal crystallization kinetics of monoglyceride (MAG) organogels were studied by pulsed nuclear magnetic resonance (pNMR) and differential scanning calorimetry (DSC), respectively. The Avrami equation was used to describe the isothermal crystallization kinetics and experimental data fitted the equation fairly well. Results showed that the crystal growth of MAG organogels was a rod-like growth of instantaneous nuclei at higher degrees of supercooling and a plate-like form with high nucleation rate at lower degrees of supercooling. The exothermic peak in nonisothermal DSC curves for the MAG organogels became wider and shifted to lower temperature when the cooling rate increased, and nonisothermal crystallization was analyzed by Mo equation. Results indicated that at the same crystallization time, to get a higher degree of relative crystallinity, a higher cooling rate was necessary. The activation energy of nonisothermal crystallization was calculated as 739.59 kJ/mol according to the Kissinger method. Therefore, as the results of the isothermal and nonisothermal crystallization kinetics for the MAG organogels obtained, the crystallization rate, crystal nucleation, and growth during the crystallization process could be preliminarily monitored through temperature and cooling rate regulation, which laid the foundation for the real industrial manufacture and application of the MAG organogels.

  11. GRANULAR ACTIVATED CARBON ADSORPTION AND INFRARED REACTIVATION: A CASE STUDY

    EPA Science Inventory

    A study evaluated the effectiveness and cost of removing trace organic contaminants and surrogates from drinking water by granular activated carbon (GAC) adsorption. The effect of multiple reactivations of spent GAC was also evaluated. Results indicated that reactivated GAC eff...

  12. Equilibrium study of selected divalent d-electron metals adsorption on A-type zeolite.

    PubMed

    Majdan, Marek; Pikus, Stanisław; Kowalska-Ternes, Monika; Głdysz-Płaska, Agnieszka; Staszczuk, Piotr; Fuks, Leon; Skrzypek, Henryk

    2003-06-15

    The objective of the presented study was to investigate the adsorption of Cu, Co, Mn, Zn, Cd and Mn on A-type zeolite. The isotherms for adsorption of metals from their nitrates were registered. The following adsorption constants K of metals were found: 162,890, 124,260, 69,025, 16,035, 10,254, and 151 [M(-1)] for Cu, Co, Mn, Zn, Cd, and Ni, respectively, for the concentration range 10(-4)-10(-3) M. On the other hand, the investigation of pH influence on the distribution constants of metals showed that the adsorption of metals proceeds essentially through an ion-exchange process, surface hydrolysis, and surface complexation. The supplementary results from DRIFT, scanning electron microscopy, and X-ray diffraction methods confirmed the presumption about the possible connection between the electronic structure of divalent ions and their adsorption behavior, showing that ions with d5 and d10 configurations such as Mn2+, Zn2+, Cd2+, with much weaker hydrolytic properties than Cu2+ and Ni2+, strongly interact with the zeolite framework and therefore their affinity to the zeolite phase is much stronger when compared with that of the Ni2+ ion, but at the same time not as strong as the affinity of the Cu2+ ion, the latter forming a new phase during the interaction with zeolite framework. For Zn2+, during inspection of the correlation between the proton concentration H/Al and zinc concentration Zn/Al on the zeolite surface, the formation of the surface complex [triple bond]S-OZn(OH) was proposed. A correlation between the heterogeneity of proton concentrations H/Al on Me-zeolite surfaces and the hydrolysis constants pKh of Me2+ ions was found. PMID:16256612

  13. Comparative Study on the Implication of Three Nanoparticles on the Removal of Trichloroethylene by Adsorption - The Pilot and Rapid Small-Scale Column Tests

    EPA Science Inventory

    The impact of three commercially-available nanoparticles (NPs) on trichloroethylene (TCE) adsorption onto granular activated carbon (GAC) was investigated. TCE Adsorption isotherm and column breakthrough experiments were conducted in the presence and absence of silicon dioxide (S...

  14. Silica coated magnetic particles using microwave synthesis for removal of dyes from natural water samples: Synthesis, characterization, equilibrium, isotherm and kinetics studies

    NASA Astrophysics Data System (ADS)

    Ahmed, Salwa A.; Soliman, Ezzat M.

    2013-11-01

    Monitoring pollutants in water samples is a challenge to analysts. So, the removal of Napthol blue black (NBB) and Erichrome blue black R (EBBR) from aqueous solutions was investigated using magnetic chelated silica particles. Magnetic solids are widely used in detection and analytical systems because of the performance advantages they offer compared to similar solids that lack magnetic properties. In this context, a fast, simple and clean method for modification of magnetic particles (Fe3O4) with silica gel was developed using microwave technique to introduce silica gel coated magnetic particles (SG-MPs) sorbent. The magnetic sorbent was characterized by the FT-IR, X-ray diffraction (XRD), and scan electron microscope (SEM) analyses. The effects of pH, time, weight of sorbent and initial concentration of dye were evaluated. It was interesting to find from results that SG-MPs exhibits high percentage extraction of the studied dyes (100% for NBB and 98.75% for EBBR) from aqueous solutions. The Freundlich isotherm with r2 = 0.973 and 0.962 and Langmuir isotherms with r2 = 0.993 and 0.988 for NBB and EBBR, respectively were used to describe adsorption equilibrium. Also, adsorption kinetic experiments have been carried out and the data have been well fitted by a pseudo-second-order equation r2 = 1.0 for NBB and 0.999 for EBBR. The prepared sorbent with rapid adsorption rate and separation convenience was applied for removal of NBB and EBBR pollutants from natural water samples with good precision (RSD% = 0.05-0.3%).

  15. Comparative studies on adsorptive removal of heavy metal ions by biosorbent, bio-char and activated carbon obtained from low cost agro-residue.

    PubMed

    Kırbıyık, Çisem; Pütün, Ayşe Eren; Pütün, Ersan

    2016-01-01

    In this study, Fe(III) and Cr(III) metal ion adsorption processes were carried out with three adsorbents in batch experiments and their adsorption performance was compared. These adsorbents were sesame stalk without pretreatment, bio-char derived from thermal decomposition of biomass, and activated carbon which was obtained from chemical activation of biomass. Scanning electron microscopy and Fourier transform-infrared techniques were used for characterization of adsorbents. The optimum conditions for the adsorption process were obtained by observing the influences of solution pH, adsorbent dosage, initial solution concentration, contact time and temperature. The optimum adsorption efficiencies were determined at pH 2.8 and pH 4.0 for Fe(III) and Cr(III) metal ion solutions, respectively. The experimental data were modelled by different isotherm models and the equilibriums were well described by the Langmuir adsorption isotherm model. The pseudo-first-order, pseudo-second-order kinetic, intra-particle diffusion and Elovich models were applied to analyze the kinetic data and to evaluate rate constants. The pseudo-second-order kinetic model gave a better fit than the others. The thermodynamic parameters, such as Gibbs free energy change ΔG°, standard enthalpy change ΔH° and standard entropy change ΔS° were evaluated. The thermodynamic study showed the adsorption was a spontaneous endothermic process. PMID:26819399

  16. Phosphate adsorption on granular palygorskite: batch and column studies.

    PubMed

    Fangqun, Gan; Jianmin, Zhou; Huoyan, Wang; Changwen, Du; Wenzhao, Zhang; Xiaoqin, Chen

    2011-02-01

    A method to prepare granular palygorskite (GPA) was put forward in this research, and its potential use to remove phosphate species from aqueous solution was assessed. Batch experiments were performed to study the adsorption equilibrium and influence of contact time and pH on the adsorption and desorption of phosphate onto GPA in water. The maximum phosphate adsorption capacity of GPA was 13.1 mg/g. Kinetic data revealed that more than 90% of phosphate was adsorbed onto GPA within 2 hours. Phosphate adsorption capacity was 0.10 mg/g in column experiments, and co-existing anions could decrease phosphate removal. The saturated column was regenerated by 0.2 mol/L sodium hydroxide, and the GPA could be reused in phosphate removal. The data obtained from both batch and column studies indicated that GPA could be used effectively to remove phosphate from water.

  17. Phosphate adsorption on lanthanum loaded biochar.

    PubMed

    Wang, Zhanghong; Shen, Dekui; Shen, Fei; Li, Tianyu

    2016-05-01

    To attain a low-cost and high-efficient phosphate adsorbent, lanthanum (La) loaded biochar (La-BC) prepared by a chemical precipitation method was developed. La-BC and its pristine biochar (CK-BC) were comparatively characterized using zeta potential, BET surface area, scanning electron microscopy/energy dispersive spectrometer (SEM-EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FT-IR). The adsorption ability and the mechanisms during adsorption process for the La-BC samples were also investigated. La loaded on the surface of biochar can be termed as La-composites (such as LaOOH, LaONO3 and La(OH)3), leading to the decrease of negative charge and surface area of biochar. La-BC exhibited the high adsorption capacity to phosphate compared to CK-BC. Adsorption isotherm and adsorption kinetic studies showed that the Langmuir isotherm and second order model could well describe the adsorption process of La-BC, indicating that the adsorption was dominated by a homogeneous and chemical process. The calculated maximum adsorption capacity was as high as 46.37 mg g(-1) (computed in P). Thermodynamic analysis revealed that the adsorption was spontaneous and endothermic. SEM, XRD, XPS and FT-IR analysis suggested that the multi-adsorption mechanisms including precipitation, ligand exchange and complexation interactions can be evidenced during the phosphate adsorption process by La-composites in La-BC. PMID:26871732

  18. Modeling and Experimental Studies of Mercury Oxidation and Adsorption in a Fixed-Bed and Entrained-Flow Reactor

    SciTech Connect

    Buitrago, Paula A.; Morrill, Mike; Lighty, JoAnn S.; Silcox, Geoffrey D.

    2009-06-01

    This report presents experimental and modeling mercury oxidation and adsorption data. Fixed-bed and single-particle models of mercury adsorption were developed. The experimental data were obtained with two reactors: a 300-W, methane-fired, tubular, quartz-lined reactor for studying homogeneous oxidation reactions and a fixed-bed reactor, also of quartz, for studying heterogeneous reactions. The latter was attached to the exit of the former to provide realistic combustion gases. The fixed-bed reactor contained one gram of coconut-shell carbon and remained at a temperature of 150°C. All methane, air, SO2, and halogen species were introduced through the burner to produce a radical pool representative of real combustion systems. A Tekran 2537A Analyzer coupled with a wet conditioning system provided speciated mercury concentrations. At 150°C and in the absence of HCl or HBr, the mercury uptake was about 20%. The addition of 50 ppm HCl caused complete capture of all elemental and oxidized mercury species. In the absence of halogens, SO2 increased the mercury adsorption efficiency to up to 30 percent. The extent of adsorption decreased with increasing SO2 concentration when halogens were present. Increasing the HCl concentration to 100 ppm lessened the effect of SO2. The fixed-bed model incorporates Langmuir adsorption kinetics and was developed to predict adsorption of elemental mercury and the effect of multiple flue gas components. This model neglects intraparticle diffusional resistances and is only applicable to pulverized carbon sorbents. It roughly describes experimental data from the literature. The current version includes the ability to account for competitive adsorption between mercury, SO2, and NO2. The single particle model simulates in-flight sorbent capture of elemental mercury. This model was developed to include Langmuir and Freundlich isotherms, rate equations, sorbent feed rate, and

  19. Grand canonical monte carlo simulation study of methane adsorption at an open graphite surface and in slit-like carbon pores at 273 K.

    PubMed

    Kowalczyk, Piotr; Tanaka, Hideki; Kaneko, Katsumi; Terzyk, Artur P; Do, Duong D

    2005-06-01

    Grand canonical Monte Carlo (GCMC) simulation was used for the systematic investigation of the supercritical methane adsorption at 273 K on an open graphite surface and in slit-like micropores of different sizes. For both considered adsorption systems the calculated excess adsorption isotherms exhibit a maximum. The effect of the pore size on the maximum surface excess and isosteric enthalpy of adsorption for methane storage at 273 K is discussed. The microscopic detailed picture of methane densification near the homogeneous graphite wall and in slit-like pores at 273 K is presented with selected local density profiles and snapshots. Finally, the reliable pore size distributions, obtained in the range of the microporosity, for two pitch-based microporous activated carbon fibers are calculated from the local excess adsorption isotherms obtained via the GCMC simulation. The current systematic study of supercritical methane adsorption both on an open graphite surface and in slit-like micropores performed by the GCMC summarizes recent investigations performed at slightly different temperatures and usually a lower pressure range by advanced methods based on the statistical thermodynamics.

  20. Adsorption study of Ammonia Nitrogen by watermelon rind

    NASA Astrophysics Data System (ADS)

    Ibrahim, A.; Yusof, L.; Beddu, N. S.; Galasin, N.; Lee, P. Y.; Lee, R. N. S.; Zahrim, A. Y.

    2016-06-01

    The utilization of fruit waste for low-cost adsorbents as a replacement for costly conventional methods of removing ammonia nitrogen from wastewater has been reviewed. The adsorption studies were conducted as a function of contact time and adsorbent dosage and it were carried out on four different adsorbents; fresh watermelon rind and modified watermelon rind with sodium hydroxide (NaOH), potassium hydroxide (KOH) and sulphuric acid (H2SO4). Adsorbents were tested for characterization by using zeta potential test and all samples shows negative values thus makes it favourable for the adsorption process. The batch experimental result showed that adsorption process is rapid and equilibrium was established within 40 minutes of contact time. The ammonia nitrogen removal rate amounted in range of 96% to 99%, and the adsorption capacities were in range of 1.21 to 1.24 mg/g for all four different types of adsorbents used.

  1. Adsorption of chromium onto activated alumina: kinetics and thermodynamics studies.

    PubMed

    Marzouk, Ikhlass; Dammak, Lassaad; Hamrouni, Béchir

    2013-02-01

    In this study, the removal of chromium (VI) by adsorption on activated alumina was investigated and the results were fitted to Langmuir, Freundlich, Dubinin-Redushkevich, and Temkin adsorption models at various temperatures. The constants of each model were evaluated depending on temperature. Thermodynamic parameters for the adsorption system were determined at 10, 25 and 40 degrees C. (deltaH degrees = -21.18 kJ x mol(-1); deltaG degrees = -8.75 to -7.43 kJ x mol(-1) and deltaS degrees = -0.043 kJ x K(-1) x mol(-1)). The obtained values showed that chromium (VI) adsorption is a spontaneous and exothermic process. The kinetic process was evaluated by first-order, second-order and Elovich kinetic models.

  2. A Comparative Study on the Adsorption of Triton X-100 and Tween 20 onto Latexes with Different Interfacial Properties

    PubMed

    Martín-Rodríguez; Cabrerizo-Vílchez; Hidalgo-Álvarez

    1997-03-01

    In this paper we have studied the adsorption of two nonionic surfactants, Triton X-100 and Tween 20 (polyoxyethylene (20) sorbitan monolaurate) onto latexes with different interfacial properties. Four different samples of polystyrene beads were used in this study. A hydrophobic sample was prepared by conventional emulsion polymerization of styrene. Hydrophilic polymer colloids were prepared by the emulsifier-free emulsion copolymerization of styrene and 2-hydroxyethylmethacrylate in different proportions and acrylic acid. In all cases potassium persulfate was used as initiator. In order to consider the mechanism of the adsorption at the different liquid-solid interfaces, adsorption isotherms under different pH and ionic strength conditions were performed. Electrokinetic characterization and colloidal stability of bare hydrophobic and hydrophilic latexes and the surfactant-latex complexes were compared to understand the effect of the nonionic surfactant on the electric double layer structure. The results showed that Tween 20 and Triton X-100 are adsorbed in the same way on surfaces with different polarity but in different amounts. Hydrophobic interaction is the main driving force in the adsorption. The effect of the adsorption on the electrokinetic properties and stability of the latexes was found to be different for hydrophobic and hydrophilic latexes as a consequence of the dissimilar interfacial properties of these two latex samples. PMID:9245323

  3. Adsorption of methylene blue from aqueous solution by graphene.

    PubMed

    Liu, Tonghao; Li, Yanhui; Du, Qiuju; Sun, Jiankun; Jiao, Yuqin; Yang, Guangming; Wang, Zonghua; Xia, Yanzhi; Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai

    2012-02-01

    Graphene was prepared using a modified Hummers' method. The physico-chemical properties of graphene were characterized by TEM, BET specific surface area, FTIR, Raman and XRD measurements. The effect factors including pH, contact time, temperature and dosage on the adsorption properties of methylene blue onto graphene were investigated. The experimental data of isotherm followed the Langmuir isotherm model better than the Freundlich model. The maximum adsorption capacity obtained from Langmuir isotherm equation at 293 K was 153.85 mg/g, indicating graphene is a good adsorbent for the adsorption of MB. The kinetic study illustrated that the adsorption of methylene blue onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of methylene blue onto graphene was an endothermic and spontaneous process.

  4. Equilibrium studies of copper ion adsorption onto palm kernel fibre.

    PubMed

    Ofomaja, Augustine E

    2010-07-01

    The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin-Radushkevich (D-R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r(2), and the non-linear Chi-square, chi(2) error analysis. The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH(PZC) of the palm kernel fibre with an optimum dose of 10g/dm(3). The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 x 10(-4)mol/g at 339K. The sorption equilibrium constant, K(a), increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B(1), with increasing temperature. The Dubinin-Radushkevich (D-R) isotherm parameter, free energy, E, was in the range of 15.7-16.7kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO(3) and CH(3)COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic. PMID:20346574

  5. Equilibrium studies of copper ion adsorption onto palm kernel fibre.

    PubMed

    Ofomaja, Augustine E

    2010-07-01

    The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin-Radushkevich (D-R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r(2), and the non-linear Chi-square, chi(2) error analysis. The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH(PZC) of the palm kernel fibre with an optimum dose of 10g/dm(3). The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 x 10(-4)mol/g at 339K. The sorption equilibrium constant, K(a), increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B(1), with increasing temperature. The Dubinin-Radushkevich (D-R) isotherm parameter, free energy, E, was in the range of 15.7-16.7kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO(3) and CH(3)COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic.

  6. Combination of computational methods, adsorption isotherms and selectivity tests for the conception of a mixed non-covalent-semi-covalent molecularly imprinted polymer of vanillin.

    PubMed

    Puzio, Kinga; Delépée, Raphaël; Vidal, Richard; Agrofoglio, Luigi A

    2013-08-01

    A novel molecularly imprinted polymer (MIP) for vanillin was prepared by photo initiated polymerization in dichloromethane using a mixed semi-covalent and non-covalent imprinting strategy. Taking polymerisable syringaldehyde as "dummy" template, acrylamide was chosen as functional monomer on B3LYP/6-31+G(d,p) density functional theory computational method basis with counterpoise. The binding parameters for the recognition of vanillin on imprinted polymers were studied with three different isotherm models (Langmuir, bi-Langmuir and Langmuir-Freundlich) and compared. The results indicate an heterogeneity of binding sites. It was found and proved by DFT calculations that the specific binding of vanillin in the cavities is due to non-covalent interactions of the template with the hydroxyphenyl- and the amide-moieties. The binding geometry of vanillin in the MIP cavity was also modelled. The obtained MIP is highly specific for vanillin (with an imprinting factor of 7.4) and was successfully applied to the extraction of vanillin from vanilla pods, red wine spike with vanillin, natural and artificial vanilla sugar with a recovery of 80%.

  7. Adsorption of Pb(II) ions from aqueous solution by native and activated bentonite: kinetic, equilibrium and thermodynamic study.

    PubMed

    Kul, Ali Riza; Koyuncu, Hülya

    2010-07-15

    In this study, the adsorption kinetics, equilibrium and thermodynamics of Pb(II) ions on native (NB) and acid activated (AAB) bentonites were examined. The specific surface areas, pore size and pore-size distributions of the samples were fully characterized. The adsorption efficiency of Pb(II) onto the NB and AAB was increased with increasing temperature. The kinetics of adsorption of Pb(II) ions was discussed using three kinetic models, the pseudo-first-order, the pseudo-second-order and the intra-particle diffusion model. The experimental data fitted very well the pseudo-second-order kinetic model. The initial sorption rate and the activation energy were also calculated. The activation energy of the sorption was calculated as 16.51 and 13.66 kJ mol(-1) for NB and AAB, respectively. Experimental results were also analysed by the Langmuir, Freundlich and Dubinin-Redushkevich (D-R) isotherm equations at different temperatures. R(L) separation factor for Langmuir and the n value for Freundlich isotherm show that Pb(II) ions are favorably adsorbed by NB and AAB. Thermodynamic quantities such as Gibbs free energy (DeltaG), the enthalpy (DeltaH) and the entropy change of sorption (DeltaS) were determined as about -5.06, 10.29 and 0.017 kJ mol(-1) K(-1), respectively for AAB. It was shown that the sorption processes were an endothermic reactions, controlled by physical mechanisms and spontaneously.

  8. Magnetic hydrogel beads based on PVA/sodium alginate/laponite RD and studying their BSA adsorption.

    PubMed

    Mahdavinia, Gholam Reza; Mousanezhad, Sedigheh; Hosseinzadeh, Hamed; Darvishi, Farshad; Sabzi, Mohammad

    2016-08-20

    In this study double physically crosslinked magnetic hydrogel beads were developed by a simple method including solution mixing of sodium alginate and poly(vinyl alcohol) (PVA) containing magnetic laponite RD (Rapid Dispersion). Sodium alginate and PVA were physically crosslinked by Ca(2+) and freezing-thawing cycles, respectively. Magnetic laponite RD nanoparticles were incorporated into the system to create magnetic response and strengthen the hydrogels. All hybrids double physically crosslinked hydrogel beads were stable under different pH values without any disintegration. Furthermore, adsorption of bovine serum albumin (BSA) on the hydrogel beads was investigated on the subject of pH, ion strength, initial BSA concentration, and temperature. Nanocomposite beads exhibited maximum adsorption capacity for BSA at pH=4.5. The experimental adsorption isotherm data were well followed Langmuir model and based on this model the maximum adsorption capacity was obtained 127.3mgg(-1) at 308K. Thermodynamic parameters revealed spontaneous and monolayer adsorption of BSA on magnetic nanocomposites beads.

  9. Soil adsorption studies of a rice herbicide, cyhalofop-butyl, in two texturally different soils of India.

    PubMed

    Sondhia, Shobha; Khare, Rishi Raj

    2014-10-01

    The ability of herbicides to be adsorbed by the soil and sediment and their tendency to be desorbed are some of the most important factors affecting soil and water contamination. Therefore, a sorption study was conducted to evaluate the adsorption of cyhalofop-butyl, butyl (2R)-2-[4-(4-cyano-2-fluorophenoxy) phenoxy] propanoate, in the sandy clay loam and clayey soils using a batch equilibrium method. The adsorption of cyhalofop-butyl was found positively related with the clay and organic carbon content. Freundlich constants (Kf) of cyhalofop-butyl in the clayey and sandy clay loam were found to be 13.39 and 2.21, respectively. Sorption coefficients (Koc) and distribution coefficients (Kd) were found to be 265.38 and 2,092.79, and 1.38 and 11.48, for sandy clay loam and clayey soils, respectively. The adsorption isotherm suggested a relatively higher affinity of cyhalofop-butyl to the adsorption sites at low equilibrium concentrations. The low value of the soil organic carbon partition coefficient (Koc) of cyhalofop-butyl in the sandy loam soil suggested its weaker adsorption in soil and thus increased its risk of mobility into water sources; hence, it should be used judiciously to prevent groundwater contamination.

  10. Soil adsorption studies of a rice herbicide, cyhalofop-butyl, in two texturally different soils of India.

    PubMed

    Sondhia, Shobha; Khare, Rishi Raj

    2014-10-01

    The ability of herbicides to be adsorbed by the soil and sediment and their tendency to be desorbed are some of the most important factors affecting soil and water contamination. Therefore, a sorption study was conducted to evaluate the adsorption of cyhalofop-butyl, butyl (2R)-2-[4-(4-cyano-2-fluorophenoxy) phenoxy] propanoate, in the sandy clay loam and clayey soils using a batch equilibrium method. The adsorption of cyhalofop-butyl was found positively related with the clay and organic carbon content. Freundlich constants (Kf) of cyhalofop-butyl in the clayey and sandy clay loam were found to be 13.39 and 2.21, respectively. Sorption coefficients (Koc) and distribution coefficients (Kd) were found to be 265.38 and 2,092.79, and 1.38 and 11.48, for sandy clay loam and clayey soils, respectively. The adsorption isotherm suggested a relatively higher affinity of cyhalofop-butyl to the adsorption sites at low equilibrium concentrations. The low value of the soil organic carbon partition coefficient (Koc) of cyhalofop-butyl in the sandy loam soil suggested its weaker adsorption in soil and thus increased its risk of mobility into water sources; hence, it should be used judiciously to prevent groundwater contamination. PMID:24875347

  11. Study of polyethyleneimine- and amidoxime-functionalized hybrid biomass of Spirulina (Arthrospira) platensis for adsorption of uranium (VI) ion.

    PubMed

    Bayramoglu, Gulay; Akbulut, Aydin; Arica, M Yakup

    2015-11-01

    This study investigates the potential application of the polyethyleneimine- (PEI) and amidoxime-modified Spirulina (Arthrospira) platensis biomasses for the removal of uranium ion in batch mode using the native biomass as a control system. The uranium ion adsorption was also characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, zeta potential analysis, and surface area measurement studies. The effects of pH, biomass amount, contact time, initial uranium ion concentration, and ionic strength were evaluated by using native and modified algal biomass preparations. The uranium ion removal was rapid, with more than 70% of total adsorption taking place in 40 min, and equilibrium was established within 60 min. From the experimental data, it was found that the amount of adsorption uranium ion on the algal preparations decreased in the following series: amidoxime-modified algal biomass > PEI-modified algal biomass > native algal biomass. Maximum adsorption capacities of amidoxime- and PEI-modified, and native algal biomasses were found to be 366.8, 279.5, and 194.6 mg/g, respectively, in batchwise studies. The adsorption rate of U(VI) ion by amidoxime-modified algal biomass was higher than those of the native and PEI-modified counterparts. The adsorption processes on all the algal biomass preparations followed by the Dubinin-Radushkevitch (D-R) and Temkin isotherms and pseudo-second-order kinetic models. The thermodynamic parameters were determined at four different temperatures (i.e., 15, 25, 35, and 45 °C) using the thermodynamics constant of the Temkin isotherm model. The ΔH° and ΔG° values of U(VI) ion adsorption on algal preparations show endothermic heat of adsorption; higher temperatures favor the process. The native and modified algal biomass preparations were regenerated using 10 mM HNO3. These results show that amidoxime-modified algal biomass can be a potential candidate for effective removal of U(VI) ion from

  12. Study of polyethyleneimine- and amidoxime-functionalized hybrid biomass of Spirulina (Arthrospira) platensis for adsorption of uranium (VI) ion.

    PubMed

    Bayramoglu, Gulay; Akbulut, Aydin; Arica, M Yakup

    2015-11-01

    This study investigates the potential application of the polyethyleneimine- (PEI) and amidoxime-modified Spirulina (Arthrospira) platensis biomasses for the removal of uranium ion in batch mode using the native biomass as a control system. The uranium ion adsorption was also characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, zeta potential analysis, and surface area measurement studies. The effects of pH, biomass amount, contact time, initial uranium ion concentration, and ionic strength were evaluated by using native and modified algal biomass preparations. The uranium ion removal was rapid, with more than 70% of total adsorption taking place in 40 min, and equilibrium was established within 60 min. From the experimental data, it was found that the amount of adsorption uranium ion on the algal preparations decreased in the following series: amidoxime-modified algal biomass > PEI-modified algal biomass > native algal biomass. Maximum adsorption capacities of amidoxime- and PEI-modified, and native algal biomasses were found to be 366.8, 279.5, and 194.6 mg/g, respectively, in batchwise studies. The adsorption rate of U(VI) ion by amidoxime-modified algal biomass was higher than those of the native and PEI-modified counterparts. The adsorption processes on all the algal biomass preparations followed by the Dubinin-Radushkevitch (D-R) and Temkin isotherms and pseudo-second-order kinetic models. The thermodynamic parameters were determined at four different temperatures (i.e., 15, 25, 35, and 45 °C) using the thermodynamics constant of the Temkin isotherm model. The ΔH° and ΔG° values of U(VI) ion adsorption on algal preparations show endothermic heat of adsorption; higher temperatures favor the process. The native and modified algal biomass preparations were regenerated using 10 mM HNO3. These results show that amidoxime-modified algal biomass can be a potential candidate for effective removal of U(VI) ion from

  13. Isothermal Calorimeter

    NASA Technical Reports Server (NTRS)

    Rowlette, John J.

    1990-01-01

    Pressure-feedback signal indicates rate of heating. Improved isothermal calorimeter measures rate of heating in object under test. Called "isothermal" because chamber holding object and its environment maintained at or near constant temperature to minimize spurious tranfers of heat introducing errors into measurements. When item under test generates heat, rate of boiling and pressure in inner chamber increase. Servo-valve opens wider to maintain preset differential pressure. Valve-control voltage used as measure of rate of heating.

  14. EFFECT OF GAC CHARACTERISTICS ON ADSORPTION OF ORGANIC POLLUTANTS

    EPA Science Inventory

    The impact of the characteristics of granular activated carbon (GAC) on adsorption capacity and on the potential for polymerization of phenolic compounds on the surface of GAC in the presence of molecular oxygen is evaluated in this study. Adsorption isotherm data were collected...

  15. Effect of Grain Size on Uranium(VI) Surface Complexation Kinetics and Adsorption Additivity

    SciTech Connect

    Shang, Jianying; Liu, Chongxuan; Wang, Zheming; Zachara, John M.

    2011-07-27

    Laboratory experiments were performed to investigate the contribution of variable grain sizes to uranium adsorption/desorption in a sediment collected from the US DOE Hanford site. The sediment was wet-sieved into four size fractions: coarse sand (1-2 mm), medium sand (0.2-1 mm), fine sand (0.05-0.2 mm), and clay/silt fraction (< 0.05mm). For each size fraction and their composite (sediment), batch experiments were performed to determine uranium adsorption isotherms, and stirred flow-cell experiments were conducted to derive kinetic data of uranium adsorption and subsequent desorption. The results showed that uranium adsorption isotherms and adsorption/desorption kinetics were size-specific, reflecting the effects of size-specific adsorption site concentration and kinetic rate constants. The larger-size fraction had a larger mass percentage in the sediment, but with a smaller adsorption site concentration and generally a slower uranium adsorption/desorption rate. The same equilibrium surface complexation reaction and reaction constant could describe uranium adsorption isotherms for all size fractions and the composite after accounting for the effect of adsorption site concentration. Mass-weighted, linear additivity was observed for both uranium adsorption isotherms and adsorption/desorption kinetics in the composite. Our analysis also showed that uranium adsorption site concentration estimated from the adsorption isotherms was 3 orders of magnitude less than a site concentration estimated from sediment surface area and generic site density. One important implication of this study is that grain size distribution may be used to estimate uranium adsorption site, and adsorption/desorption kinetic rates in heterogeneous sediments from a common location.

  16. Mechanistic understanding and performance of biosorption of metal ions by grapefruit peel using FTIR spectroscopy, kinetics and adsorption isotherms modeling, alkali and alkaline metal displacement and EDX analysis

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The performance and mechanism of the sorptive removal of Ni2+ and Zn2+ from aqueous solution using grapefruit peel (GFP) as a new sorbent was investigated. The sorption process was fast, equilibrium was established in 60 min. The equilibrium process was described well by the Langmuir isotherm model,...

  17. Detection of Chlamydia trachomatis by isothermal ramification amplification method: a feasibility study.

    PubMed

    Zhang, Wandi; Cohenford, Menashi; Lentrichia, Brian; Isenberg, Henry D; Simson, Elkin; Li, Hengjin; Yi, Jizu; Zhang, David Y

    2002-01-01

    Chlamydia trachomatis is the leading cause of sexually transmitted disease in the United States. Effective screening for this agent can facilitate prompt treatment and prevent its sequelae. The recent introduction of liquid-based cytology has made possible the simultaneous screening of cervical intraepithelial lesions and detection of C. trachomatis in a single collection vial. In this study we determined whether cytological fluid could support DNA-based amplification for the detection of C. trachomatis. Three methods were compared, including ramification amplification (RAM), real-time PCR with molecular beacon, and Abbott's ligase chain reaction (LCx). RAM is a novel, recently introduced, isothermal DNA amplification technique that utilizes a circular probe for target detection and achieves exponential amplification through the mechanism of primer extension, strand displacement, and ramification. Our results show that RAM can detect as few as 10 C. trachomatis elementary bodies in less than 2 h, comparable to results with real-time PCR. Thirty clinical specimens collected in PreservCyt solution were tested by LCx, real-time PCR, and RAM. Among 30 specimens, 15 were positive by PCR and LCx and 14 were positive by RAM. One specimen missed by RAM had an inadequate amount of residual cellular material. Our results show that nucleic acid amplification methods can serve to detect C. trachomatis and presumably other sexually transmitted agents in cytological fluid and that the RAM assay can be an alternative to PCR and LCx because of its simplicity and isothermal amplification.

  18. Characterization of biochars derived from agriculture wastes and their adsorptive removal of atrazine from aqueous solution: A comparative study.

    PubMed

    Liu, Na; Charrua, Alberto Bento; Weng, Chih-Huang; Yuan, Xiaoling; Ding, Feng

    2015-12-01

    The physicochemical properties of biochars produced from soybeans (SBB), corn stalks (CSB), rice stalks (RSB), poultry manure (PMB), cattle manure (CMB), and pig manure (PgMB) and their adsorption characteristics of atrazine were investigated. The adsorption capacity increased with the increase of temperature and initial atrazine concentration. More atrazine was removed from basic solutions than acidic solutions, due to the effects of adsorption and hydrolysis. The Freundlich isotherm adsorption parameters indicated that the adsorption capacity decreased in the order SBB>RSB>CMB>CSB>PMB>PgMB, which is associated to the pore volume of biochars. The total pore volume and biochar pH were concluded to play important roles in determining the adsorption capacity, and they may have contributed to physical adsorption mechanisms dominating the overall adsorption process (the low activation energy for all of the biochars). Modified Freundlich and intraparticle diffusion models were used to describe the kinetics of the adsorption process.

  19. Arsenic Removal: Adsorptive Media and Coagulation/Filtration Case Studies

    EPA Science Inventory

    This presentation provides information on the results of three case studies from USEPA arsenic demonstration program. The first case study presented is on the Rimrock, AZ project that used an adsorptive media technology (E33 media) to remove arsenic. The second case study is on...

  20. Petroleum resins adsorption onto quartz sand: near infrared (NIR) spectroscopy study.

    PubMed

    Balabin, Roman M; Syunyaev, Rustem Z

    2008-02-15

    In this paper we have tried to evaluate adsorption parameters of petroleum resins. Near infrared (NIR) spectroscopy is applied for resins bulk concentration evaluation during adsorption process. NIR experimental scheme and parameters are provided. NIR spectra range of 9000-13,000 cm(-1) is chosen. Quartz sand (0.2-0.8 mm fraction) is used as adsorbent; benzene is used as solvent. Different approaches of "NIR spectra-resins concentration" calibration model building are discussed. Partial least squares (PLS) regression method is used. Langmuir model is chosen for experimental data fitting. Combined usage of kinetic and isothermic data gives us ability to evaluate the maximal adsorbed mass density, the equilibrium constant of adsorption, and the rate constants of adsorption (and desorption). The rate constants of resins adsorption and desorption are found to be concentration independent.

  1. Adsorptive removal of heavy metals by magnetic nanoadsorbent: an equilibrium and thermodynamic study

    NASA Astrophysics Data System (ADS)

    Shirsath, D. S.; Shirivastava, V. S.

    2015-11-01

    An efficient and new magnetic nanoadsorbent photocatalyst was fabricated by co-precipitation technique. This research focuses on understanding metal removal process and developing a cost-effective technology for treatment of heavy metal-contaminated industrial wastewater. In this investigation, magnetic nanoadsorbent has been employed for the removal of Zn(II) ions from aqueous solutions by a batch adsorption technique. The adsorption equilibrium data fitted very well to Langmuir and Freundlich adsorption isotherm models. The thermodynamics of Zn(II) ions adsorption onto the magnetic nanoadsorbents indicated that the adsorption was spontaneous, endothermic and physical in nature. Surface morphology of magnetic nanoadsorbent by scanning electron microscopy (SEM) and elemental analysis by EDX technique. The structural and photocatalytic properties of magnetic nanoadsorbent were characterized using X-ray diffraction (XRD) and FTIR techniques. Also, the magnetic properties of synthesized magnetic nanoadsorbent were determined by vibrating spinning magnetometer (VSM).

  2. Kinetic studies of microfabricated biosensors using local adsorption strategy.

    PubMed

    Zhang, Menglun; Huang, Jingze; Cui, Weiwei; Pang, Wei; Zhang, Hao; Zhang, Daihua; Duan, Xuexin

    2015-12-15

    Micro/nano scale biosensors integrated with the local adsorption mask have been demonstrated to have a better limit of detection (LOD) and less sample consumptions. However, the molecular diffusions and binding kinetics in such confined droplet have been less studied which limited further development and application of the local adsorption method and imposed restrictions on discovery of new signal amplification strategies. In this work, we studied the kinetic issues via experimental investigations and theoretical analysis on microfabricated biosensors. Mass sensitive film bulk acoustic resonator (FBAR) sensors with hydrophobic Teflon film covering the non-sensing area as the mask were introduced. The fabricated masking sensors were characterized with physical adsorption of bovine serum albumin (BSA) and specific binding of antibody and antigen. Over an order of magnitude improvement on LOD was experimentally monitored. An analytical model was introduced to discuss the target molecule diffusion and binding kinetics in droplet environment, especially the crucial effects of incubation time, which has been less covered in previous local adsorption related literatures. An incubation time accumulated signal amplification effect was theoretically predicted, experimentally monitored and carefully explained. In addition, device optimization was explored based on the analytical model to fully utilize the merits of local adsorption. The discussions on the kinetic issues are believed to have wide implications for other types of micro/nano fabricated biosensors with potentially improved LOD.

  3. [Fluoride adsorption form drinking water by granular lanthanum alginate].

    PubMed

    Huo, Ya-Kun; Ding, Wen-Ming; Huang, Xia

    2010-11-01

    Granular lanthanum alginate was prepared by dripping solved sodium alginate into lanthanum chloride solution. After washed and dried, sorbent with 1-1.5 mm diameter, 25% (mass fraction) La content was made and applied for fluoride removal from drinking test. Adsorption performance such as adsorption rate, adsorption isotherm, pH and disturbing ions effects were tested in batch adsorption. The changes of adsorbent surface and the solution composition before and after adsorption were also studied. Results showed that the adsorption rate was fast, fluoride concentration trend to stable after 2h reaction, and the adsorption rate fit for pseudo second order equation. The adsorption was significantly affected by pH and some disturbing ions, optimum pH = 4, phosphate and carbonate reduced adsorption. Adsorption isotherm fitted Langmuir equation well; the max adsorption capacity was 197.2 mg x g(-1). SEM photographs of sorbent before and after adsorption showed significantly different surface morphology; EDX composition analysis of sorbent surface and solution concentration changes before and after adsorption showed that ion exchange take placed between solution F- and sorbent surface Cl- and OH-.

  4. Study of char gasification in a reaction/adsorption apparatus

    SciTech Connect

    Sotirchos, S.V.; Crowley, J.A.

    1987-09-01

    The reaction of an activated carbon (coconut char) with CO/sub 2/ was studied in a reaction/adsorption apparatus which allows successive reactivity and physical adsorption measurements to be made on the same solid sample. Reaction and surface area evolution data were obtained in the temperature range from 800 to 900/sup 0/C. All reaction rate trajectories obtained in this study showed a maximum in the reaction rate, 2-3 times higher than the initial rate, at about 85% conversion. There was no correlation between these results and the evolution of the internal surface area although the reaction appeared to take place initially in the kinetically controlled regime.

  5. Adsorptive removal of PPCPs by biomorphic HAP templated from cotton.

    PubMed

    Huang, Bin; Xiong, Dan; Zhao, Tingting; He, Huan; Pan, Xuejun

    2016-01-01

    Biomorphic nano-hydroxyapatite (HAP) was fabricated by a co-precipitation method using cotton as bio-templates and employed in adsorptive removal of ofloxacin (OFL) and triclosan (TCS) that are two representative pharmaceuticals and personal care products (PPCPs). The surface area and porosity, crystal phase, functional group, morphology and micro-structure of the synthesized HAP were characterized by Brunauer-Emmett-Teller isotherm, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron macroscopic and transmission electron microscopy. The effects of initial pH, ionic strength, initial concentration, contact time and temperature on the removal of PPCPs were studied in a batch experiment. The adsorption of OFL and TCS was rapid and almost accomplished within 50 min. Kinetic studies indicated that the adsorption process of OFL and TCS followed the pseudo-first-order and pseudo-second-order models, respectively. The Freundlich isotherm described the OFL adsorption process well but the adsorption of TCS fitted the Langmuir isotherm better. Thermodynamics and isotherm parameters suggested that both OFL and TCS adsorption were feasible and spontaneous. Hydrogen bond and Lewis acid-base reaction may be the dominating adsorption mechanism of OFL and TCS, respectively. Compared to other adsorbents, biomorphic HAP is environmentally friendly and has the advantages of high adsorption capacity, exhibiting potential application for PPCPs removal. PMID:27387006

  6. Adsorption of phenolic compound by aged-refuse.

    PubMed

    Xiaoli, Chai; Youcai, Zhao

    2006-09-01

    The adsorption of phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol by aged-refuse has been studied. Adsorption isotherms have been determined for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol and the data fits well to the Freundlich equation. The chlorinated phenols are absorbed more strongly than the phenol and the adsorption capacity has an oblivious relationship with the numbers and the position of chlorine subsistent. The experiment data suggests that both the partition function and the chemical adsorption involve in the adsorption process. Pseudo-first-order and pseudo-second-order model were applied to investigate the kinetics of the adsorption and the results show that it fit the pseudo-second-order model. More than one step involves in the adsorption process and the overall rate of the adsorption process appears to be controlled by the chemical reaction. The thermodynamic analysis indicates that the adsorption is spontaneous and endothermic.

  7. Equilibrium and column adsorption studies of 2,4-dinitroanisole (DNAN) on surface modified granular activated carbons.

    PubMed

    Boddu, V M; Abburi, K; Fredricksen, A J; Maloney, S W; Damavarapu, R

    2009-02-01

    2,4-Dinitroanisole (DNAN) is used as a component extensively in the development of insensitive munitions. This may result in release of DNAN into the environment. Here, the results are reported of a study on the removal characteristics of DNAN through adsorption on granular activated carbon (GAC), chitosan coated granular activated carbon (CGAC), acid treated granular activated carbon (AGAC) and alkali treated granular activated carbon (BGAC) under equilibrium and column flow conditions. The effect of pH, contact time, concentration of DNAN, and presence of electrolytes on the uptake of DNAN by the adsorbents was investigated. The equilibrium data were fitted to different types of adsorption isotherms. The data were further analysed on the basis of Lagergren first-order, pseudo second-order and intraparticle diffusion kinetic models. Breakthrough curves were obtained based on column flow results. All the adsorbents were capable of removing about 99% of DNAN from aqueous media, except CGAC which adsorbed about 87% of DNAN.

  8. Protein nanoparticle interaction: A spectrophotometric approach for adsorption kinetics and binding studies

    NASA Astrophysics Data System (ADS)

    Vaishanav, Sandeep K.; Chandraker, Kumudini; Korram, Jyoti; Nagwanshi, Rekha; Ghosh, Kallol K.; Satnami, Manmohan L.

    2016-08-01

    Investigating the protein nanoparticle interaction is crucial to understand how to control the biological interactions of nanoparticles. In this work, Model protein Bovine serum albumin (BSA) was used to evaluate the process of protein adsorption to the gold nanoparticles (GNPs) surface. The binding of a model protein (BSA) to GNPs was investigated through fluorescence quenching measurements. The strong affinities of BSA for GNPs were confirmed by the high value of binding constant (Ks) which was calculated to be 2.2 × 1011 L/mol. In this consequence, we also investigated the adsorption behavior of BSA on GNPs surface via UV-Vis spectroscopy. The effect of various operational parameters such as pH, contact time, initial BSA concentration, and temperature on adsorption of BSA was investigated using batch adsorption experiments. Kinetics of adsorption was found to follow the pseudo-second order rate equation. The suitability of Freundlich and Langmuir adsorption models to the equilibrium data was investigated. The equilibrium adsorption was well described by the Freundlich isotherm model. The maximum adsorption capacity for BSA adsorbed on GNPs was 58.71 mg/g and equilibrium constant was 0.0058 calculated by the Langmuir model at 298 K and pH = 11.0. Thermodynamic parameters showed that the adsorption of BSA onto GNPs was feasible, spontaneous, and exothermic.

  9. Calcium lignosulfonate adsorption and desorption on Berea sandstone.

    PubMed

    Grigg, Reid B; Bai, Baojun

    2004-11-01

    This paper describes adsorption and desorption studies carried out with calcium lignosulfonate (CLS) on Berea sandstone. Circulation experiments were performed to determine CLS adsorption isotherms and the effects of CLS concentration, temperature, salinity, brine hardness, and injection rate on adsorption density. Flow-through experiments were performed to assess the reversibility of CLS adsorption and the influence of postflush rate, brine concentration, brine hardness, brine pH, and temperature on the desorption process. Results indicate that CLS adsorption isotherms on Berea sandstone follow the Freundlich isotherm law. The results presented in this paper on the effects of CLS adsorption and desorption on Berea sandstone show that: (1) increasing CLS concentration and salinity increases CLS adsorption density; (2) increasing temperature will decrease adsorption density; (3) increasing injection rate of CLS solution will slightly decrease CLS adsorption density; (4) postflush rate and salinity of brine have a large impact on the CLS desorption process; (5) the adsorption and desorption process are not completely reversible; and (5) temperature and pH of the postflush brine have little effect on desorption.

  10. Adsorption of silver dimer on graphene - A DFT study

    SciTech Connect

    Kaur, Gagandeep; Gupta, Shuchi; Rani, Pooja; Dharamvir, Keya

    2014-04-24

    We performed a systematic density functional theory (DFT) study of the adsorption of silver dimer (Ag{sub 2}) on graphene using SIESTA (Spanish Initiative for Electronic Simulations with Thousands of Atoms) package, in the generalized gradient approximation (GGA). The adsorption energy, geometry, and charge transfer of Ag2-graphene system are calculated. The minimum energy configuration for a silver dimer is parallel to the graphene sheet with its two atoms directly above the centre of carbon-carbon bond. The negligible charge transfer between the dimer and the surface is also indicative of a weak bond. The methodology demonstrated in this paper may be applied to larger silver clusters on graphene sheet.

  11. Thermooxidative stability of poppy seeds studied by non-isothermal DSC measurements.

    PubMed

    Cibulková, Zuzana; Čertík, Milan; Dubaj, Tibor

    2014-05-01

    Papaver somniferum L. is an important crop cultivated mostly for seed production. Poppy seeds have a high nutritive value and are used as a food and as a source of edible oil. This oil is a rich source of polyunsaturated fatty acids. It is well known that the unsaturated fatty acids easily undergo oxidation reactions, which lead to the reduction of shelf life, nutritional quality, development of unpleasant tastes and odors. The goal of this study was to develop the methodology for testing the stability of poppy seeds using non-isothermal DSC. For the treatment of the experimental data a method based on non-Arrhenian temperature function has been applied and the values the kinetic parameters have been obtained. In order to assess the durability of the commercial poppy seeds, the lengths of induction periods have been calculated.

  12. The complexity of condensed tannin binding to bovine serum albumin--An isothermal titration calorimetry study.

    PubMed

    Kilmister, Rachel L; Faulkner, Peta; Downey, Mark O; Darby, Samuel J; Falconer, Robert J

    2016-01-01

    Isothermal titration calorimetry was applied to study the binding of purified proanthocyanidin oligomers to bovine serum albumin (BSA). The molecular weight of the proanthocyanidin oligomer had a major impact on its binding to BSA. The calculated change in enthalpy (ΔH) and association constant (Ka) became greater as the oligomer size increased then plateaued at the heptameric oligomer. These results support a model for precipitation of proteins by proanthocyanidin where increased oligomer size enhanced the opportunity for cross linkages between proteins ultimately forming sediment-able complexes. The authors suggest tannin binding to proteins is opportunistic and involves multiple sites, each with a different Ka and ΔH of binding. The ΔH of binding comprises both an endothermic hydrophobic interaction and exothermic hydrogen bond component. This suggests the calculated entropy value (ΔS) for tannin-protein interactions is subject to a systematic error and should be interpreted with caution.

  13. Non-Isothermal Experimental Study of the Constrained Vapor Bubble Thermosyphon

    NASA Technical Reports Server (NTRS)

    Karthikeyan, Muthu; Huang, Jianming; Plawsky, Joel; Wayner, Peter, Jr.

    1996-01-01

    Experimental and theoretical techniques to study non-isothermal transport processes in the constrained vapor bubble thermosyphon (CVBT) were developed using a pentane/quartz system. The transport processes can be evaluated by measuring the liquid film profile, which gives the pressure field, and the temperature field. The axial variation in the capillary pressure was measured using an image-analyzing interferometer that is based on computer-enhanced video microscopy of the naturally occurring interference fringes. Thermoelectric coolers were used to control the temperature level in the condensation region and, therefore, the length of the approximately 'adiabatic' surface region which is a function of the temperature difference between the CVBT surface and the surroundings. High values for the axial thermal conductance in the 'adiabatic' surface region were demonstrated under certain conditions.

  14. Binding of chrysoidine to catalase: spectroscopy, isothermal titration calorimetry and molecular docking studies.

    PubMed

    Yang, Bingjun; Hao, Fang; Li, Jiarong; Chen, Dongliang; Liu, Rutao

    2013-11-01

    Chrysoidine is an industrial azo dye and the presence of chrysoidine in water and food has become an environmental concern due to its negative effects on human beings. In this work, the interactions between chrysoidine and bovine liver catalase (BLC) were explored. Obvious loss in catalytic activity was observed after incubation of BLC with chrysoidine, and the inhibition effect of BLC was found to be of the non-competitive type. No profound conformational change of BLC occurs in the presence of chrysoidine as revealed by UV-vis absorption, circular dichroism and fluorescence spectroscopy studies. Isothermal titration calorimetry results indicate that catalase has two sets of binding sites for chrysoidine. Further, molecular docking simulations show that chrysoidine is located within the bottleneck in the main channel of the substrate to the active site of BLC, which explain the activity inhibition of BLC by chrysoidine. PMID:24001681

  15. Uranium adsorption studies on aminopropyl modified mesoporous sorbent (NH 2-MCM-41) using statistical design method

    NASA Astrophysics Data System (ADS)

    Sert, Şenol; Eral, Meral

    2010-11-01

    MCM-41 has been synthesized and modified in order to graft amine groups on its surface. The modified NH 2-MCM-41 adsorbent was characterized by using XRD, SEM, surface area and porosity analyzer, and FT-IR. This characterized adsorbent was investigated for uranium adsorption using the batch method. The central composite design (CCD) combined with the response surface methodology (RSM) was selected to determine the effects of parameters and their interactions for the removal of UO22+ ions. The optimum values of the parameters determined were 4.2 for the initial pH, 60 °C for the temperature, 90 mg L -1 for the initial concentration and 173 min for the shaking time using the response surface methodology. Δ H° and Δ S° were calculated from the slope and the intercept of plots of ln K d versus 1/ T. The isotherm models, Langmuir, Freundlich, Dubinin-Radushkevich (D-R) have been studied to explain the adsorption characteristics.

  16. Adsorption studies of cationic, anionic and azo-dyes via monodispersed Fe3O4 nanoparticles.

    PubMed

    Chaudhary, Ganga Ram; Saharan, Priya; Kumar, Arun; Mehta, S K; Mor, Suman; Umar, Ahmad

    2013-05-01

    The present paper reports the applicability of magnetite (Fe3O4) nanoparticles as an adsorbent for the removal of three dyes viz. Acridine orange (cationic dye), Comassie Brilliant Blue R-250 (anionic dye) and Congo red (azo dye) from their aqueous solution. The Fe3O4 nanoparticles were synthesized via simple chemical precipitation method using CTAB, as surfactant. The as-prepared nanoparticles were characterized in terms of their morphological, structural and optical properties by using transmission electron microscopy X-ray diffraction and UV-visible spectroscopic measurements. The dye removal efficiency of Fe3O4 NPs have been determined by investigating several factors such as effect of pH, amount of adsorbent dose and effect of contact time on different dye concentrations. Langmuir and Freundlich adsorption isotherms have also been studied to explain the interaction of dyes. The experimental data indicate that the adsorption rate follows pseudo- second-order kinetics for the removal of all the three dyes. Moreover, the nanoparticles and the adsorbed dyes were desorbed. The identities of recovered nanoparticles as well as the three dyes have been found, as same and were reused. PMID:23858837

  17. Microcalorimetric study of adsorption and disassembling of virus-like particles on anion exchange chromatography media.

    PubMed

    Yu, Mengran; Zhang, Songping; Zhang, Yan; Yang, Yanli; Ma, Guanghui; Su, Zhiguo

    2015-04-01

    Chromatographic purification of virus-like particles (VLPs) is important to the development of modern vaccines. However, disassembly of the VLPs on the solid-liquid interface during chromatography process could be a serious problem. In this study, isothermal titration calorimetric (ITC) measurements, together with chromatography experiments, were performed on the adsorption and disassembling of multi-subunits hepatitis B virus surface antigen virus-like particles (HB-VLPs). Two gigaporous ion-exchange chromatography (IEC) media, DEAE-AP-280 nm and DEAE-POROS, were used. The application of gigaporous media with high ligand density led to significantly increased irreversible disassembling of HB-VLPs and consequently low antigen activity recovery during IEC process. To elucidate the thermodynamic mechanism of the effect of ligand density on the adsorption and conformational change of VLPs, a thermodynamic model was proposed. With this model, one can obtain the intrinsic molar enthalpy changes related to the binding of VLPs and the accompanying conformational change on the liquid-solid interface during its adsorption. This model assumes that, when intact HB-VLPs interact with the IEC media, the total adsorbed proteins contain two states, the intact formation and the disassembled formation; accordingly, the apparent adsorption enthalpy, ΔappH, which can be directly measured from ITC experiments, presents the sum of three terms: (1) the intrinsic molar enthalpy change associated to the binding of intact HB-VLPs (ΔbindHintact), (2) the intrinsic molar enthalpy change associated to the binding of HB-VLPs disassembled formation (ΔbindHdis), and (3) the enthalpy change accompanying the disassembling of HB-VLPs (ΔconfHdis). The intrinsic binding of intact HB-VLPs and the disassembled HB-VLPs to both kinds of gigaporous media (each of which has three different ligand densities), were all observed to be entropically driven as indicated by positive values of

  18. Microcalorimetric study of adsorption and disassembling of virus-like particles on anion exchange chromatography media.

    PubMed

    Yu, Mengran; Zhang, Songping; Zhang, Yan; Yang, Yanli; Ma, Guanghui; Su, Zhiguo

    2015-04-01

    Chromatographic purification of virus-like particles (VLPs) is important to the development of modern vaccines. However, disassembly of the VLPs on the solid-liquid interface during chromatography process could be a serious problem. In this study, isothermal titration calorimetric (ITC) measurements, together with chromatography experiments, were performed on the adsorption and disassembling of multi-subunits hepatitis B virus surface antigen virus-like particles (HB-VLPs). Two gigaporous ion-exchange chromatography (IEC) media, DEAE-AP-280 nm and DEAE-POROS, were used. The application of gigaporous media with high ligand density led to significantly increased irreversible disassembling of HB-VLPs and consequently low antigen activity recovery during IEC process. To elucidate the thermodynamic mechanism of the effect of ligand density on the adsorption and conformational change of VLPs, a thermodynamic model was proposed. With this model, one can obtain the intrinsic molar enthalpy changes related to the binding of VLPs and the accompanying conformational change on the liquid-solid interface during its adsorption. This model assumes that, when intact HB-VLPs interact with the IEC media, the total adsorbed proteins contain two states, the intact formation and the disassembled formation; accordingly, the apparent adsorption enthalpy, ΔappH, which can be directly measured from ITC experiments, presents the sum of three terms: (1) the intrinsic molar enthalpy change associated to the binding of intact HB-VLPs (ΔbindHintact), (2) the intrinsic molar enthalpy change associated to the binding of HB-VLPs disassembled formation (ΔbindHdis), and (3) the enthalpy change accompanying the disassembling of HB-VLPs (ΔconfHdis). The intrinsic binding of intact HB-VLPs and the disassembled HB-VLPs to both kinds of gigaporous media (each of which has three different ligand densities), were all observed to be entropically driven as indicated by positive values of

  19. Adsorption modeling for off-gas treatment

    SciTech Connect

    Ladshaw, A.; Sharma, K.; Yiacoumi, S.; Tsouris, C.; De Paoli, D.W.

    2013-07-01

    Off-gas generated from the reprocessing of used nuclear fuel contains a mixture of several radioactive gases including {sup 129}I{sub 2}, {sup 85}Kr, HTO, and {sup 14}CO{sub 2}. Over the past few decades, various separation and recovery processes have been studied for capturing these gases. Adsorption data for gaseous mixtures of species can be difficult to determine experimentally. Therefore, procedures capable of predicting the adsorption behavior of mixtures need to be developed from the individual isotherms of each of the pure species. A particular isotherm model of interest for the pure species is the Generalized Statistical Thermodynamic Adsorption isotherm. This model contains an adjustable number of parameters and will therefore describe a wide range of adsorption isotherms for a variety of components. A code has been developed in C++ to perform the non-linear regression analysis necessary for the determination of the isotherm parameters, as well as the least number of parameters needed to describe an entire set of data. (authors)

  20. Adsorption of boric acid on pure and humic acid coated am-Al(OH)3: A boron K-edge XANES study.

    PubMed

    Xu, Dani; Peak, Derek

    2007-02-01

    The fate and mobility of boric acid in the environment is largely controlled by adsorption reactions with soil organic matter and soil minerals to form surface complexes (Soil Sci Soc. Am. J. 1991, 55, 1582; Geochim. Cosmochim. Acta 2002, 67, 2551; Soil Sci. Soc. Am. J. 1995, 59, 405; Environ. Sci. Technol. 1995, 29, 302). In this study, boric acid adsorption on pure am-Al(OH)3 and 5% (w/w) humic acid (HA) coated am-Al(OH)3 were investigated both as a function of pH (4.5-11) and initial boric acid concentration (0-4.5 mmol L(-1)). Batch adsorption isotherm experiments were also conducted with samples exposed to atmospheric CO2 and anaerobic (N2) conditions to examine the effects of dissolved CO2 on boric acid adsorption. Boron (B) K-edge X-ray absorption near-edge structure (XANES) spectroscopy was used to investigate the coordination of boric acid adsorbed at mineral/water interfaces. The XANES spectra of boric acid adsorption samples showed that both trigonally and tetrahedrally coordinated B complexes were present on the mineral surface. Both macroscopic and spectroscopic experiments revealed that the combination of HA coating on am-Al(OH)3 and dissolved CO2 decreased boric acid adsorption compared to adsorption on pure am-Al(OH)3.

  1. Adsorption of CTAB onto perlite samples from aqueous solutions.

    PubMed

    Alkan, Mahir; Karadaş, Mecit; Doğan, Mehmet; Demirbaş, Ozkan

    2005-11-15

    In this study, the adsorption properties of unexpanded and expanded perlite samples in aqueous cetyltrimethylammonium bromide (CTAB) solutions were investigated as a function of ionic strength, pH, and temperature. It was found that the amount of cetyltrimethylammonium bromide adsorbed onto unexpanded perlite was greater than that onto expanded perlite. For both perlite samples, the sorption capacity increased with increasing ionic strength and pH and decreasing temperature. Experimental data were analyzed by Langmuir and Freundlich isotherms and it was found that the experimental data were correlated reasonably well by the Freundlich adsorption isotherm. Furthermore, the isotherm parameters (KF and n) were also calculated. The adsorption enthalpy was determined from experimental data at different temperatures. Results have shown that the interaction between the perlite surface and CTAB is a physical interaction, and the adsorption process is an exothermic one.

  2. Protein Adsorption on Surfaces with Grafted Polymers

    PubMed Central

    Szleifer, I.

    1997-01-01

    A general theoretical framework for studying the adsorption of protein molecules on surfaces with grafted polymers is presented. The approach is a generalization of the single-chain mean-field theory, in which the grafted polymer-protein-solvent layer is assumed to be inhomogeneous in the direction perpendicular to the grafting surface. The theory enables the calculation of the adsorption isotherms of the protein as a function of the surface coverage of grafted polymers, concentration of protein in bulk, and type of solvent molecules. The potentials of mean force of the protein with the surface are calculated as a function of polymer surface coverage and amount of protein adsorbed. The theory is applied to model lysozyme on surfaces with grafted polyethylene oxide. The protein is modeled as spherical in solution, and it is assumed that the protein-polymer, protein-solvent, and polymer-solvent attractive interactions are all equal. Therefore, the interactions determining the structure of the layer (beyond the bare polymer-surface and protein-surface interactions) are purely repulsive. The bare surface-protein interaction is taken from atomistic calculations by Lee and Park. For surfaces that do not have preferential attractions with the grafted polymer segments, the adsorption isotherms of lysozyme are independent of the polymer length for chains with more than 50 ethylene oxide units. However, the potentials of mean force show strong variations with grafted polymer molecular weight. The competition between different conformations of the adsorbed protein is studied in detail. The adsorption isotherms change qualitatively for surfaces with attractive interactions with ethylene oxide monomers. The protein adsorption is a function of chain length—the longer the polymer the more effective it is in preventing protein adsorption. The structure of the layer and its deformation upon protein adsorption are very important in determining the adsorption isotherms and the

  3. Removal of anionic surfactants from aqueous solutions by adsorption onto high area activated carbon cloth studied by in situ UV spectroscopy.

    PubMed

    Ayranci, Erol; Duman, Osman

    2007-09-01

    The removal of anionic surfactants, benzene sulfonate (BS), p-toluene sulfonate (TS), 4-octylbenzene sulfonate (OBS) and 4-dodecylbenzene sulfonate (DBS) from water and 0.01 M H(2)SO(4) solutions by adsorption onto high area activated carbon cloth (ACC) were studied by in situ UV-spectroscopic technique. The various properties of the ACC were given and the in situ UV-spectroscopic technique was described. Both kinetic and isotherm data were obtained for the adsorption of surfactants. Kinetic data were treated according to intraparticle diffusion, pseudo-first-order, pseudo-second-order and Elovich models. They were found to fit the pseudo-second-order model best. Isotherm data were treated according to well-known Langmuir and Freundlich models. The regression analysis of the data showed that Freundlich model represents the isotherm data of the surfactants better. The rate and extent of adsorption of surfactants were found to increase in the order BSadsorption was found to be enhanced by the presence of 0.01 M H(2)SO(4) in the surfactant solution due to electrostatic attractions between the negatively charged surfactant molecules and the ACC surface which acquired a net positive charge in acidic medium. An inert electrolyte such as NaCl was found to decrease the adsorption capacity of the ACC for the anionic surfactants. PMID:17363147

  4. Biosorption of aquatic copper (II) by mushroom biomass Pleurotus eryngii: kinetic and isotherm studies.

    PubMed

    Kan, Shi-Hong; Sun, Bai-Ye; Xu, Fang; Song, Qi-Xue; Zhang, Sui-Fang

    2015-01-01

    Biosorption is an effective method for removing heavy metals from effluent. This work mainly aimed to evaluate the adsorption performance of the widely cultivated novel mushroom, Pleurotus eryngii, for the removal of Cu(II) from single aqueous solutions. Kinetics and equilibria were obtained using a batch technique. The sorption kinetics follows the pseudo-second-order model, whereas the adsorption equilibria are best described by the Langmuir model. The adsorption process is exothermic because both the Langmuir-estimated biosorption capacity and the heat of adsorption estimated from the Temkin model decreased with increasing tested temperature. Based on the adsorption intensity estimated by the Freundlich model and the mean adsorption free energy estimated by the Dubinin-Radushkevich model, the type of adsorption is defined as physical adsorption. The biomass of the macro-fungus P. eryngii has the potential to remove Cu(II) from a large-scale wastewater contaminated by heavy metals, because of its favorable adsorption, short biosorption equilibrium time of 20 min and remarkable biosorption capacity (15.19 mg g⁻¹ as calculated by the Langmuir model). The adsorbed metal-enriched mushroom is a high-quality bio-ore by the virtue of its high metal content of industrial mining grade and easy metal extractability. PMID:25633953

  5. In vitro study on fluoxetine adsorption onto charcoal using potentiometry.

    PubMed

    Atta-Politou, J; Skopelitis, I; Apatsidis, I; Koupparis, M

    2001-01-01

    This in vitro investigation was performed to study the adsorption rate constant as well as the adsorption characteristics of fluoxetine (F) to activated charcoal and its commercial formulation Carbomix powder in simulated gastric (pH 1.2) fluid environment. Ion-selective electrode (ISE) potentiometry, based on the selective, direct and continuous monitoring of F with an F-ISE constructed in our laboratory was used. The method used in the kinetic experiments consists of the rapid addition of a slurry containing the charcoal into the drug solution under stirring and continuous recording of the F-ISE potential until the establishment of equilibrium. The free ionized drug concentration at appropriate time intervals was calculated from the recorded adsorption curve and the apparent adsorption rate constant was estimated assuming pseudo first order kinetics. Within run R.S.D. of the estimates ranged from 0.24 to 11.5%, while between run R.S.D. (n=3-4) ranged from 0.90 to 13.8%. A linear relationship was found between the apparent adsorption rate constants and the amount of charcoal used with slopes (+/-S.D.) for activated charcoal and Carbomix equal to 1.14(+/-0.21) and 0.146(+/-0.009) s(-1)g(-1), respectively. Successive additions of microvolumes of F solution were made into a charcoal slurry with measurement of the F-ISE potential at equilibrium. The maximum adsorption capacity values (+/-S.D.) of activated charcoal and Carbomix were 254.8+/-1.8 and 405+/-41 mg/g, respectively while the affinity constant values (+/-S.D.) were 45.6+/-2.2 and 55.5+/-2.9 l/g, respectively. The adsorption of F to charcoals was rapid and for amounts of charcoal 10 times greater than the amount of the drug, 95% of F was adsorbed within the first 5 min. Relative to the toxic and lethal doses in cases of F intoxications, both types of charcoals tested adsorbed effectively F at gastric pH. Carbomix can be considered as appropriate charcoal formulation for medical treatment in cases of F

  6. Linearised and non-linearised isotherm models optimization analysis by error functions and statistical means.

    PubMed

    Subramanyam, Busetty; Das, Ashutosh

    2014-01-01

    In adsorption study, to describe sorption process and evaluation of best-fitting isotherm model is a key analysis to investigate the theoretical hypothesis. Hence, numerous statistically analysis have been extensively used to estimate validity of the experimental equilibrium adsorption values with the predicted equilibrium values. Several statistical error analysis were carried out. In the present study, the following statistical analysis were carried out to evaluate the adsorption isotherm model fitness, like the Pearson correlation, the coefficient of determination and the Chi-square test, have been used. The ANOVA test was carried out for evaluating significance of various error functions and also coefficient of dispersion were evaluated for linearised and non-linearised models. The adsorption of phenol onto natural soil (Local name Kalathur soil) was carried out, in batch mode at 30 ± 20 C. For estimating the isotherm parameters, to get a holistic view of the analysis the models were compared between linear and non-linear isotherm models. The result reveled that, among above mentioned error functions and statistical functions were designed to determine the best fitting isotherm. PMID:25018878

  7. Adsorption of o-cresol and benzoic acid in an adsorber packed with an ion-exchange resin: A comparative study of diffusional models

    SciTech Connect

    Run-Tun Huang; Teh-Liang Chen; Hung-Shan Weng

    1994-10-01

    Both solid- and pore-diffusion models were employed to simulate the adsorption of o-cresol and benzoic acid in a fixed-bed adsorber packed with an anion-exchange resin. The equilibrium adsorption data were modeled by a Langmuir isotherm. When the shape of the adsorption isotherm was approximately linear (as in the case of o-cresol), both models agreed well with the experimental break-through data, and they could be effectively applied to predict the breakthrough curve of longer columns. For a favorable adsorption isotherm (say, benzoic acid), however, better results were obtained by using the solid-diffusion model. In addition to the shape of the adsorption isotherm, several factors, such as the type of adsorbent, modeling of equilibrium data, computation efficiency, and concentration dependence of the intraparticle diffusivity, should also be taken into account for selecting a suitable diffusion model.

  8. Scoping study for the adsorption of tetraphenylborate decomposition products

    SciTech Connect

    Martin, K.B.

    2000-03-30

    This study examined the adsorption (Kd) of tetraphenylborate decomposition products - triphenylborane (3PB), diphenylborinic acid (2PB), and phenylboronic acid (1PB) from a simulated waste solution. The focus areas included three adsorbents: activated carbon, silica bonded with octyldecylsilane (C18), and silica bonded with a quaternary ammonium salt (Quat). The study examined the adsorbents at two concentrations, 100 and 200 g/L in salt simulant.

  9. Binding of copper to lysozyme: Spectroscopic, isothermal titration calorimetry and molecular docking studies.

    PubMed

    Jing, Mingyang; Song, Wei; Liu, Rutao

    2016-07-01

    Although copper is essential to all living organisms, its potential toxicity to human health have aroused wide concerns. Previous studies have reported copper could alter physical properties of lysozyme. The direct binding of copper with lysozyme might induce the conformational and functional changes of lysozyme and then influence the body's resistance to bacterial attack. To better understand the potential toxicity and toxic mechanisms of copper, the interaction of copper with lysozyme was investigated by biophysical methods including multi-spectroscopic measurements, isothermal titration calorimetry (ITC), molecular docking study and enzyme activity assay. Multi-spectroscopic measurements proved that copper quenched the intrinsic fluorescence of lysozyme in a static process accompanied by complex formation and conformational changes. The ITC results indicated that the binding interaction was a spontaneous process with approximately three thermodynamical binding sites at 298K and the hydrophobic force is the predominant driven force. The enzyme activity was obviously inhibited by the addition of copper with catalytic residues Glu 35 and Asp 52 locating at the binding sites. This study helps to elucidate the molecular mechanism of the interaction between copper and lysozyme and provides reference for toxicological studies of copper.

  10. Binding of copper to lysozyme: Spectroscopic, isothermal titration calorimetry and molecular docking studies.

    PubMed

    Jing, Mingyang; Song, Wei; Liu, Rutao

    2016-07-01

    Although copper is essential to all living organisms, its potential toxicity to human health have aroused wide concerns. Previous studies have reported copper could alter physical properties of lysozyme. The direct binding of copper with lysozyme might induce the conformational and functional changes of lysozyme and then influence the body's resistance to bacterial attack. To better understand the potential toxicity and toxic mechanisms of copper, the interaction of copper with lysozyme was investigated by biophysical methods including multi-spectroscopic measurements, isothermal titration calorimetry (ITC), molecular docking study and enzyme activity assay. Multi-spectroscopic measurements proved that copper quenched the intrinsic fluorescence of lysozyme in a static process accompanied by complex formation and conformational changes. The ITC results indicated that the binding interaction was a spontaneous process with approximately three thermodynamical binding sites at 298K and the hydrophobic force is the predominant driven force. The enzyme activity was obviously inhibited by the addition of copper with catalytic residues Glu 35 and Asp 52 locating at the binding sites. This study helps to elucidate the molecular mechanism of the interaction between copper and lysozyme and provides reference for toxicological studies of copper. PMID:27089183

  11. Binding of copper to lysozyme: Spectroscopic, isothermal titration calorimetry and molecular docking studies

    NASA Astrophysics Data System (ADS)

    Jing, Mingyang; Song, Wei; Liu, Rutao

    2016-07-01

    Although copper is essential to all living organisms, its potential toxicity to human health have aroused wide concerns. Previous studies have reported copper could alter physical properties of lysozyme. The direct binding of copper with lysozyme might induce the conformational and functional changes of lysozyme and then influence the body's resistance to bacterial attack. To better understand the potential toxicity and toxic mechanisms of copper, the interaction of copper with lysozyme was investigated by biophysical methods including multi-spectroscopic measurements, isothermal titration calorimetry (ITC), molecular docking study and enzyme activity assay. Multi-spectroscopic measurements proved that copper quenched the intrinsic fluorescence of lysozyme in a static process accompanied by complex formation and conformational changes. The ITC results indicated that the binding interaction was a spontaneous process with approximately three thermodynamical binding sites at 298 K and the hydrophobic force is the predominant driven force. The enzyme activity was obviously inhibited by the addition of copper with catalytic residues Glu 35 and Asp 52 locating at the binding sites. This study helps to elucidate the molecular mechanism of the interaction between copper and lysozyme and provides reference for toxicological studies of copper.

  12. Adsorption of Roxarsone onto Drinking Water Treatment Residuals: Preliminary Studies

    NASA Astrophysics Data System (ADS)

    Salazar, J.; Sarkar, D.; Datta, R.; Sharma, S.

    2006-05-01

    Roxarsone (3-nitro-4-hydroxyphenyl-arsonic acid) is an organo-arsenical compound, commonly used as a feed additive in the broiler poultry industry to control coccidial intestinal parasites. Roxarsone is not toxic to the birds not only because of the low dose, and also because it most likely does not convert to toxic inorganic arsenic (As) in their systems. However, upon excretion, roxarsone may undergo transformation to inorganic As, posing a serious risk of contaminating the agricultural land and water bodies via surface runoff or leaching. The use of poultry litter as fertilizer results in As accumulation rates of up to 50 metric tons per year in agricultural lands. The immediate challenge, as identified by the various regulatory bodies in recent years is to develop an efficient, yet cost-effective and environmentally sound approach to cleaning up such As- contaminated soils. Recent studies conducted by our group have suggested that the drinking water treatment residuals (WTRs) can effectively retain As, thereby decreasing its mobility in the environment. The WTRs are byproducts of drinking water treatment processes and are typically composed of amorphous Fe/Al oxides, activated C and cationic polymers. They can be obtained free-of-cost from water treatment plants. It is well demonstrated that the environmental mobility of As is controlled by adsorption/desorption reactions onto mineral surfaces. Hence, knowledge of adsorption and desorption of As onto the WTRs is of environmental relevance. The reported study examined the adsorption and desorption characteristics of As using two types of WTRs, namely the Fe-WTRs (byproduct of Fe salt treatment), and the Al-WTRs (byproduct of Al salt treatment). All adsorption experiments were carried out in batch and As retention on the WTRs was investigated as a function of solid/solution ratio (1:5, 1:10, 1:25 and 1:50), equilibration time (10 min - 48 hr), pH (2 - 10) and initial As load (100, 500, 1000 and 2000 mg As/L). The

  13. Effects of potential models on the adsorption of ethane and ethylene on graphitized thermal carbon black. Study of two-dimensional critical temperature and isosteric heat versus loading.

    PubMed

    Do, D D; Do, H D

    2004-12-01

    Adsorption of ethylene and ethane on graphitized thermal carbon black and in slit pores whose walls are composed of graphene layers is studied in detail to investigate the packing efficiency, the two-dimensional critical temperature, and the variation of the isosteric heat of adsorption with loading and temperature. Here we used a Monte Carlo simulation method with a grand canonical Monte Carlo ensemble. A number of two-center Lennard-Jones (LJ) potential models are investigated to study the impact of the choice of potential models in the description of adsorption behavior. We chose two 2C-LJ potential models in our investigation of the (i) UA-TraPPE-LJ model of Martin and Siepmann for ethane and Wick et al. for ethylene and (ii) AUA4-LJ model of Ungerer et al. for ethane and Bourasseau et al. for ethylene. These models are used to study the adsorption of ethane and ethylene on graphitized thermal carbon black. It is found that the solid-fluid binary interaction parameter is a function of adsorbate and temperature, and the adsorption isotherms and heat of adsorption are well described by both the UA-TraPPE and AUA models, although the UA-TraPPE model performs slightly better. However, the local distributions predicted by these two models are slightly different. These two models are used to explore the two-dimensional condensation for the graphitized thermal carbon black, and these values are 110 K for ethylene and 120 K for ethane.

  14. Studies of isothermal crystallisation kinetics of sunflower hard stearin-based confectionery fats.

    PubMed

    Bootello, Miguel A; Hartel, Richard W; Levin, Madeline; Martínez-Blanes, Jose M; Real, Concepción; Garcés, Rafael; Martínez-Force, Enrique; Salas, Joaquín J

    2013-08-15

    The crystallisation and polymorphic properties of three sunflower hard stearins (SHSs) and cocoa butter equivalents (CBEs) formulated by blending SHSs and palm mid fraction (PMF) were studied and compared with those from cocoa butter (CB), to explore their possibilities as confectionery fats. The isothermal crystallisation kinetics of these fats were examined by pNMR and DSC at three different temperatures. All samples studied displayed a two-step crystallisation profile that could be fitted to an exponential-Gompertz equation. Stop-and-return DSC studies showed that SHSs and CBEs exhibited different crystallisation mechanisms according to their triacylglycerol composition, with a quick formation of metastable crystals, followed by a polymorphic transition to the more stable β or β' forms. X-ray diffraction (XRD) was used to investigate the polymorphic forms of tempered SHSs and CBEs in the long term. In all cases the resulting fats displayed short spacing patterns associated with β polymorphism. These formulations based on SHSs and PMF met all the requirements to be considered as CBEs; therefore they could be used as an alternative to traditional confectionery fats.

  15. Identification of a new alpha-2-macroglobulin: Multi-spectroscopic and isothermal titration calorimetry study.

    PubMed

    Rehman, Ahmed Abdur; Ahsan, Haseeb; Khan, Fahim Halim

    2016-02-01

    A α2M homologue was isolated from sheep (Ovis aries) blood plasma, using a simple two-step procedure, ammonium sulphate fractionation and gel filtration chromatography. Sheep α2M was found to be a large tetrameric glycoprotein of 630 kDa with monomeric subunit of 133 kDa each. Each subunit of sheep α2M was found to be made up of two fragments of 102 and 31 kDa respectively. The proteinase inhibitor from sheep was found to have Stokes radius of 79Ǻ, which makes it much more compact than its human homologue. It entraps only 1 mol of trypsin per mole of inhibitor, like its caprine counterpart. The use of isothermal titration calorimetry has become gold standard for exploring thermodynamics of binding interactions. In this study, binding interaction of trypsin with alpha-2-macroglobulin is studied using ITC. The thermodynamic signatures--enthalpy change (ΔH), entropy change (ΔS) and Gibb's free energy change (ΔG), along with number of binding sites (N) and affinity constant (K) are explored for α2M-trypsin binding for the first time for any known α2M molecule. The thermodynamics of proteinase-antiproteinase association suggests that trypsin-α2M interaction is enthalpy driven event.

  16. Batch study of arsenate (V) adsorption using Akadama mud: Effect of water mineralization

    NASA Astrophysics Data System (ADS)

    Chen, Rongzhi; Zhang, Zhenya; Feng, Chuanping; Lei, Zhongfang; Li, Yuan; Li, Miao; Shimizu, Kazuya; Sugiura, Norio

    2010-02-01

    Akadama mud, consisting mainly of different forms of iron and aluminum oxide minerals, was used for arsenate (V) adsorption from aqueous solutions. The adsorption process fitted the first-order kinetic equation and the Langmuir monolayer model well. The adsorption capacity, estimated by the Langmuir isotherm model, was 5.30 mg/g at 20 ± 0.5 °C. The effects of the solution properties (initial concentration of As (V), pH, temperature, and mineralization degree) on As (V) removal were investigated. Various mineralization degrees in underground water were simulated by adjusting the ionic strength of the solution or adding coexisting ions to the contaminated solution. It was found that mineralization of the water significantly influenced the arsenic adsorption. The existence of multivalent metallic cations significantly enhanced the As (V) adsorption ability, whereas competing anions such as fluoride and phosphate greatly decreased the As (V) adsorption. This result suggests that Akadama mud is more suitable for arsenic adsorption in low-level phosphate and fluoride solutions. The loaded Akadama mud could be desorbed at polar pH conditions, especially in acidic conditions, and more than 65% As (V) sorption has been achieved at pH 1.

  17. Adsorption of sodium diclofenac on graphene: a combined experimental and theoretical study.

    PubMed

    Jauris, I M; Matos, C F; Saucier, C; Lima, E C; Zarbin, A J G; Fagan, S B; Machado, F M; Zanella, I

    2016-01-21

    The interactions of sodium diclofenac drug (s-DCF) with different graphene species were investigated using both first principles calculations based on Density Functional Theory (DFT) and adsorption experiments. Through batch adsorption experiments, it was found that rGO was a good adsorbent for removing the s-DCF drug from aqueous solutions. The general-order kinetic model shows the best fit to the experimental data compared with pseudo-first order and pseudo-second order kinetic adsorption models. The equilibrium data (at 25 °C) were fitted to the Liu isotherm model. The maximum sorption capacity for adsorption of the s-DCF drug was 59.67 mg g(-1) for rGO. The s-DCF adsorption onto pristine graphene, graphene with a vacancy, reduced oxide graphene (rGO) and functionalized graphene nanoribbons were simulated providing a good understanding of the adsorption process of this molecule on graphene-family surfaces. The results predict a physisorption regime in all cases. Based on these results, the ab initio calculations and the adsorption experiments point out that the graphene-family are promising materials for extracting s-DCF from wastewater effluents.

  18. Structural study of Fe (II) adsorption on hematite (1102)

    SciTech Connect

    Tanwar, K.S.; Petitto, S.C.; Ghose, S.K.; Eng, P.J.; Trainor, T.P.

    2008-07-15

    The structure of {alpha}-Fe{sub 2}O{sub 3}(1{bar 1}02) reacted with Fe(II) under anoxic conditions was studied using crystal truncation rod (CTR) diffraction. The CTR results show the crystalline termination of {alpha}-Fe{sub 2}O{sub 3}(1{bar 1}02) is modified due to adsorption of Fe(II) at crystallographic lattice sites. In addition, the binding sites for adsorbed Fe are similar for all studied conditions: reaction for 2 h at pH 5.0, for 34 d at pH 5.0, and for 5.5 h at pH 7.0. The occupancy of adsorbed Fe increases with both reaction time and pH, which is consistent with typical cation adsorption behavior on iron (hydr)oxide surfaces. The metal-oxygen bond lengths of the (ordered) surface Fe atoms are characteristic of Fe(III), which provides indirect evidence for oxidation of adsorbed Fe(II) and is consistent with recent studies indicating that Fe(III)-hydroxides are effective oxidants for dissolved ferrous iron. Grazing-incidence X-ray diffraction measurements indicate that no crystalline surface reaction products formed during the course of Fe(II) reaction. Overall, the structural characterization of the Fe(II) adsorption reaction results in an enhanced understanding of how reduced iron affects the structure, stability and reactivity of hematite.

  19. Study of the isothermal transformation of ductile iron with 0.5% Cu by electrical resistance measurement

    SciTech Connect

    Lin, B.Y.; Chen, E.T.; Lei, T.S.

    1995-10-01

    A computer-controlled system for measuring electrical resistance has been developed and used to study the isothermal transformation of austenite in a ductile iron (3.31% C, 3.12% Si, 0.22% mn, 0.55% Cu). The ability of the technique to follow the isothermal decomposition of austenite was established by measurements on an AISI 4340 steel. The times at which the austenite decomposed to primary ferrite, pearlite, and bainite were accurately detected. In the ductile iron, the formation of pearlite and of bainite was easily detected, and an isothermal transformation diagram was constructed from the results. The temperature range for the formation of bainite is especially important in producing austempered ductile iron (ADI) and was mapped. An initial stage of decomposition of austenite to ferrite and high-carbon austenite is followed by a time delay; then the high-carbon austenite decomposes to bainite. The formation of ADI requires austempering to a structure of ferrite and high-carbon austenite, then quenching to retain this structure, thus avoiding the formation of bainite. This is achieved by isothermal transformation into the time-delay region. For the ductile iron studied here, this time region was about 2.6 h at 400 C and increased to 277 h at 300 C.

  20. Study of the isothermal transformation of ductile iron with 0.5% Cu by electrical resistance measurement

    NASA Astrophysics Data System (ADS)

    Lin, B. Y.; Chen, E. T.; Lei, T. S.

    1995-10-01

    A computer-controlled system for measuring electrical resistance has been developed and used to study the isothermal transformation of austenite in a ductile iron (3.31 % C, 3.12 % Si, 0.22 % Mn, 0.55 % Cu). The ability of the technique to follow the isothermal decomposition of austenite was established by measurements on an AISI4340 steel. The times at which the austenite decomposed to primary ferrite, pearlite, and bainite were accurately detected. In the ductile iron, the formation of pearlite and of bainite was easily detected, and an isothermal transformation diagram was constructed from the results. The temperature range for the formation of bainite is especially important in producing austempered ductile iron (ADI) and was mapped. An initial stage of decomposition of austenite to ferrite and high-carbon austenite is followed by a time delay; then the high-carbon austenite decomposes to bainite. The formation of ADI requires austempering to a structure of ferrite and high-carbon austenite, then quenching to retain this structure, thus avoiding the formation of bainite. This is achieved by isothermal transformation into the time-delay region. For the ductile iron studied here, this time region was about 2.6 h at 400 °C and increased to 277 h at 300 °C.

  1. Study on adsorption and desorption of ammonia on graphene

    NASA Astrophysics Data System (ADS)

    Zhang, Zhengwei; Zhang, Xinfang; Luo, Wei; Yang, Hang; He, Yanlan; Liu, Yixing; Zhang, Xueao; Peng, Gang

    2015-09-01

    The gas sensor based on pristine graphene with conductance type was studied theoretically and experimentally. The time response of conductance measurements showed a quickly and largely increased conductivity when the sensor was exposed to ammonia gas produced by a bubble system of ammonia water. However, the desorption process in vacuum took more than 1 h which indicated that there was a larger number of transferred carriers and a strong adsorption force between ammonia and graphene. The desorption time could be greatly shortened down to about 2 min by adding the flow of water-vapor-enriched air at the beginning of the recovery stage which had been confirmed as a rapid and high-efficiency desorption process. Moreover, the optimum geometries, adsorption energies, and the charge transfer number of the composite systems were studied with first-principle calculations. However, the theoretical results showed that the adsorption energy between NH3 and graphene was too small to fit for the experimental phenomenon, and there were few charges transferred between graphene and NH3 molecules, which was completely different from the experiment measurement. The adsorption energy between NH4 and graphene increased stage by stage which showed NH4 was a strong donor. The calculation suggested that H2O molecule could help a quick desorption of NH4 from graphene by converting NH4 to NH3 or (NH3)n(H2O)m groups, which was consistent with the experimental results. This study demonstrates that the ammonia gas produced by a bubble system of ammonia water is mainly ammonium groups of NH3 and NH4, and the NH4 moleculars are ideal candidates for the molecular doping of graphene while the interaction between graphene and the NH3 moleculars is weak.

  2. Study on adsorption and desorption of ammonia on graphene.

    PubMed

    Zhang, Zhengwei; Zhang, Xinfang; Luo, Wei; Yang, Hang; He, Yanlan; Liu, Yixing; Zhang, Xueao; Peng, Gang

    2015-12-01

    The gas sensor based on pristine graphene with conductance type was studied theoretically and experimentally. The time response of conductance measurements showed a quickly and largely increased conductivity when the sensor was exposed to ammonia gas produced by a bubble system of ammonia water. However, the desorption process in vacuum took more than 1 h which indicated that there was a larger number of transferred carriers and a strong adsorption force between ammonia and graphene. The desorption time could be greatly shortened down to about 2 min by adding the flow of water-vapor-enriched air at the beginning of the recovery stage which had been confirmed as a rapid and high-efficiency desorption process. Moreover, the optimum geometries, adsorption energies, and the charge transfer number of the composite systems were studied with first-principle calculations. However, the theoretical results showed that the adsorption energy between NH3 and graphene was too small to fit for the experimental phenomenon, and there were few charges transferred between graphene and NH3 molecules, which was completely different from the experiment measurement. The adsorption energy between NH4 and graphene increased stage by stage which showed NH4 was a strong donor. The calculation suggested that H2O molecule could help a quick desorption of NH4 from graphene by converting NH4 to NH3 or (NH3)n(H2O)m groups, which was consistent with the experimental results. This study demonstrates that the ammonia gas produced by a bubble system of ammonia water is mainly ammonium groups of NH3 and NH4, and the NH4 moleculars are ideal candidates for the molecular doping of graphene while the interaction between graphene and the NH3 moleculars is weak.

  3. Nitrotyrosine adsorption on defective graphene: A density functional theory study

    NASA Astrophysics Data System (ADS)

    Majidi, R.; Karami, A. R.

    2015-06-01

    We have applied density functional theory to study adsorption of nitrotyrosine on perfect and defective graphene sheets. The graphene sheets with Stone-Wales (SW) defect, pentagon-nonagon (5-9) single vacancy, and pentagon-octagon-pentagon (5-8-5) double vacancy were considered. The calculations of adsorption energy showed that nitrotyrosine presents a more strong interaction with defective graphene rather than with perfect graphene sheet. The order of interaction strength is: SW>5-9>5-8-5>perfect graphene. It is found that the electronic properties of perfect and defective graphene are sensitive to the presence of nitrotyrosine. Hence, graphene sheets can be considered as a good sensor for detection of nitrotyrosine molecule which is observed in connection with several human disorders, such as Parkinson's and Alzheimer's disease.

  4. Adsorption of methylene blue onto activated carbon produced from tea (Camellia sinensis L.) seed shells: kinetics, equilibrium, and thermodynamics studies.

    PubMed

    Gao, Jun-Jie; Qin, Ye-Bo; Zhou, Tao; Cao, Dong-Dong; Xu, Ping; Hochstetter, Danielle; Wang, Yue-Fei

    2013-07-01

    Tea (Camellia sinensis L.) seed shells, the main byproduct of the manufacture of tea seed oil, were used as precursors for the preparation of tea activated carbon (TAC) in the present study. A high yield (44.1%) of TAC was obtained from tea seed shells via a one-step chemical method using ZnCl2 as an agent. The Brunauer-Emmett-Teller (BET) surface area and the total pore volumes of the obtained TAC were found to be 1530.67 mg(2)/g and 0.7826 cm(3)/g, respectively. The equilibrium adsorption results were complied with Langmuir isotherm model and its maximum monolayer adsorption capacity was 324.7 mg/g for methylene blue. Adsorption kinetics studies indicated that the pseudo-second-order model yielded the best fit for the kinetic data. An intraparticle diffusion model suggested that the intraparticle diffusion was not the only rate-controlling step. Thermodynamics studies revealed the spontaneous and exothermic nature of the sorption process. These results indicate that tea seed shells could be utilized as a renewable resource to develop activated carbon which is a potential adsorbent for methylene blue.

  5. Adsorption of methylene blue onto activated carbon produced from tea (Camellia sinensis L.) seed shells: kinetics, equilibrium, and thermodynamics studies*

    PubMed Central

    Gao, Jun-jie; Qin, Ye-bo; Zhou, Tao; Cao, Dong-dong; Xu, Ping; Hochstetter, Danielle; Wang, Yue-fei

    2013-01-01

    Tea (Camellia sinensis L.) seed shells, the main byproduct of the manufacture of tea seed oil, were used as precursors for the preparation of tea activated carbon (TAC) in the present study. A high yield (44.1%) of TAC was obtained from tea seed shells via a one-step chemical method using ZnCl2 as an agent. The Brunauer-Emmett-Teller (BET) surface area and the total pore volumes of the obtained TAC were found to be 1 530.67 mg2/g and 0.782 6 cm3/g, respectively. The equilibrium adsorption results were complied with Langmuir isotherm model and its maximum monolayer adsorption capacity was 324.7 mg/g for methylene blue. Adsorption kinetics studies indicated that the pseudo-second-order model yielded the best fit for the kinetic data. An intraparticle diffusion model suggested that the intraparticle diffusion was not the only rate-controlling step. Thermodynamics studies revealed the spontaneous and exothermic nature of the sorption process. These results indicate that tea seed shells could be utilized as a renewable resource to develop activated carbon which is a potential adsorbent for methylene blue. PMID:23825151

  6. Graphene oxide and adsorption of chloroform: A density functional study

    NASA Astrophysics Data System (ADS)

    Kuisma, Elena; Hansson, C. Fredrik; Lindberg, Th. Benjamin; Gillberg, Christoffer A.; Idh, Sebastian; Schröder, Elsebeth

    2016-05-01

    Chlorinated hydrocarbon compounds are of environmental concerns, since they are toxic to humans and other mammals, and are widespread, and exposure is hard to avoid. Understanding and improving methods to reduce the amount of the substances are important. We present an atomic-scale calculational study of the adsorption of chlorine-based substance chloroform (CHCl3) on graphene oxide, as a step in estimating the capacity of graphene oxide for filtering out such substances, e.g., from drinking water. The calculations are based on density functional theory, and the recently developed consistent-exchange functional for the van der Waals density-functional method is employed. We obtain values of the chloroform adsorption energy varying from roughly 0.2 to 0.4 eV per molecule. This is comparable to previously found results for chloroform adsorbed directly on clean graphene, using similar calculations. In a wet environment, like filters for drinking water, the graphene will not stay clean and will likely oxidize, and thus adsorption onto graphene oxide, rather than clean graphene, is a more relevant process to study.

  7. Graphene oxide and adsorption of chloroform: A density functional study.

    PubMed

    Kuisma, Elena; Hansson, C Fredrik; Lindberg, Th Benjamin; Gillberg, Christoffer A; Idh, Sebastian; Schröder, Elsebeth

    2016-05-14

    Chlorinated hydrocarbon compounds are of environmental concerns, since they are toxic to humans and other mammals, and are widespread, and exposure is hard to avoid. Understanding and improving methods to reduce the amount of the substances are important. We present an atomic-scale calculational study of the adsorption of chlorine-based substance chloroform (CHCl3) on graphene oxide, as a step in estimating the capacity of graphene oxide for filtering out such substances, e.g., from drinking water. The calculations are based on density functional theory, and the recently developed consistent-exchange functional for the van der Waals density-functional method is employed. We obtain values of the chloroform adsorption energy varying from roughly 0.2 to 0.4 eV per molecule. This is comparable to previously found results for chloroform adsorbed directly on clean graphene, using similar calculations. In a wet environment, like filters for drinking water, the graphene will not stay clean and will likely oxidize, and thus adsorption onto graphene oxide, rather than clean graphene, is a more relevant process to study. PMID:27179497

  8. Adsorption studies of methylene blue and gentian violet on sugarcane bagasse modified with EDTA dianhydride (EDTAD) in aqueous solutions: kinetic and equilibrium aspects.

    PubMed

    Gusmão, Karla Aparecida Guimarães; Gurgel, Leandro Vinícius Alves; Melo, Tânia Márcia Sacramento; Gil, Laurent Frédéric

    2013-03-30

    In this study the adsorption of cationic dyes by modified sugarcane bagasse with EDTA dianhydride (EB) was examined using methylene blue (MB) and gentian violet (GV) as model compounds in aqueous single solutions. The synthesized adsorbent (EB) was characterized by FTIR, elemental analysis, and BET. The capacity of EB to adsorb dyes was evaluated at different contact times, pH values, and initial dye concentrations. According to the obtained results, the adsorption processes could be described by a pseudo-second-order kinetic model. The adsorption isotherms were well fitted by the Langmuir model. Maximum adsorption capacities for MB and GV on EB were found to be 202.43 and 327.83 mg/g, respectively. The free energy change during adsorption of MB and GV was found to be -22.50 and -24.21 kJ/mol, respectively, suggesting that chemisorption is the main mechanism controlling the adsorption process. PMID:23428463

  9. Study the adsorption of sulfates by high cross-linked polystyrene divinylbenzene anion-exchange resin

    NASA Astrophysics Data System (ADS)

    Fathy, Mahmoud; Moghny, Th. Abdel; Awadallah, Ahmed E.; El-Bellihi, Abdel-Hameed A.-A.

    2014-11-01

    In response to rising concerns about the effect of sulfate on water quality, human health, and agriculture, many jurisdictions around the world are imposing tighter regulations for sulfate discharge. This is driving the need for environmental compliance in industries like mining, metal processing, pulp and paper, sewage treatment, and chemical manufacturing. The sulfate removal from synthetic water by high cross-linked polystyrene divinylbenzene resin was studied at batch experiments in this study. The effect of pH, contact time, sulfates concentration, and adsorbent dose on the sulfate sequestration was investigated. The optimum conditions were studied on Saline water as a case study. The results showed that with increasing of the absorbent amount; contact time, and pH improve the efficiency of sulfate removal. The maximum sulfates uptake was obtained in pH and contact time 3.0 and 120 min, respectively. Also, with increasing initial concentration of sulfates in water, the efficiency of sulfate removal decreased. The obtained results in this study were matched with Freundlich isotherm and pseudo-second-order kinetic. The maximum adsorption capacity (Qm) and constant rate were found 0.318 (mg/g) and 0.21 (mg/g.min), respectively. This study also showed that in the optimum conditions, the sulfate removal efficiency from Saline water by 0.1 mg/L sulfates was 65.64 %. Eventually, high cross-linked polystyrene divinylbenzene resin is recommended as a suitable and low cost absorbent to sulfate removal from aqueous solutions.

  10. The Adsorption of Reactive Blue 19 Dye onto Cucurbit[8]uril and Cucurbit[6]uril: An Experimental and Theoretical Study.

    PubMed

    Xie, Xiaomei; Li, Xiaolei; Luo, Hanhan; Lu, Huijuan; Chen, Feifei; Li, Wei

    2016-05-01

    The adsorption behavior and mechanism of Reactive Blue 19 (RB19) on cucurbit[6]uril (CB[6]) and cucurbit[8]uril (CB[8]) were investigated. The adsorption isotherm data obtained at different temperatures were fitted well to the Langmuir isotherm, and according to this model, CB[8] and CB[6] exhibited maximum monolayer adsorption capacities of 714.29 and 100.5 mg/g, respectively, at 298.15 K. The adsorption thermodynamic functions ΔG, ΔH, and ΔS were evaluated and revealed that RB19 adsorption onto CB[8] and CB[6] is a spontaneous and enthalpy-driven process. The adsorption process was determined to follow pseudo-second-order kinetics, indicating that chemisorption dominates the adsorption process. Fourier tranform IR spectroscopy, thermogravimetric analysis, and density functional theory (DFT) calculations revealed that the formation of an inclusion complex is the main driving force of adsorption. The phenyl and sulfone moieties of RB19 reside inside the cavity of CB[8], but because of the small cavity, only the sulfone of RB19 resides inside the cavity of CB[6]. Time-dependent DFT calculations revealed that all of the absorption bands of RB19 derive from π → π* transitions, while for the adsorption product of CB[8], the bands located at 590 and 287 nm derive from π → π* transitions and the bands located at 254 and 202 nm mainly derive from intermolecular charge transfer (ICT). PMID:27064317

  11. Critical analysis of adsorption data statistically

    NASA Astrophysics Data System (ADS)

    Kaushal, Achla; Singh, S. K.

    2016-09-01

    Experimental data can be presented, computed, and critically analysed in a different way using statistics. A variety of statistical tests are used to make decisions about the significance and validity of the experimental data. In the present study, adsorption was carried out to remove zinc ions from contaminated aqueous solution using mango leaf powder. The experimental data was analysed statistically by hypothesis testing applying t test, paired t test and Chi-square test to (a) test the optimum value of the process pH, (b) verify the success of experiment and (c) study the effect of adsorbent dose in zinc ion removal from aqueous solutions. Comparison of calculated and tabulated values of t and χ 2 showed the results in favour of the data collected from the experiment and this has been shown on probability charts. K value for Langmuir isotherm was 0.8582 and m value for Freundlich adsorption isotherm obtained was 0.725, both are <1, indicating favourable isotherms. Karl Pearson's correlation coefficient values for Langmuir and Freundlich adsorption isotherms were obtained as 0.99 and 0.95 respectively, which show higher degree of correlation between the variables. This validates the data obtained for adsorption of zinc ions from the contaminated aqueous solution with the help of mango leaf powder.

  12. Phosphate adsorption from wastewater using zirconium (IV) hydroxide: Kinetics, thermodynamics and membrane filtration adsorption hybrid system studies.

    PubMed

    Johir, M A H; Pradhan, M; Loganathan, P; Kandasamy, J; Vigneswaran, S

    2016-02-01

    Excessive phosphate in wastewater should be removed to control eutrophication of water bodies. The potential of employing amorphous zirconium (Zr) hydroxide to remove phosphate from synthetic wastewater was studied in batch adsorption experiments and in a submerged membrane filtration adsorption hybrid (MFAH) reactor. The adsorption data satisfactorily fitted to Langmuir, pseudo-first order and pseudo-second order models. Langmuir adsorption maxima at 22 °C and pHs of 4.0, 7.1, and 10.0 were 30.40, 18.50, and 19.60 mg P/g, respectively. At pH 7.1 and temperatures of 40 °C and 60 °C, they were 43.80 and 54.60 mg P/g, respectively. The thermodynamic parameters, ΔG° and ΔS° were negative and ΔH° was positive. FTIR, zeta potential and competitive phosphate, sulphate and nitrate adsorption data showed that the mechanism of phosphate adsorption was inner-sphere complexation. In the submerged MFAH reactor experiment, when Zr hydroxide was added at doses of 1-5 g/L once only at the start of the experiment, the removal of phosphate from 3 L of wastewater containing 10 mg P/L declined after 5 h of operation. However, when Zr hydroxide was repeatedly added at 5 g/L dose every 24 h, satisfactory removal of phosphate was maintained for 3 days.

  13. Phosphate adsorption from wastewater using zirconium (IV) hydroxide: Kinetics, thermodynamics and membrane filtration adsorption hybrid system studies.

    PubMed

    Johir, M A H; Pradhan, M; Loganathan, P; Kandasamy, J; Vigneswaran, S

    2016-02-01

    Excessive phosphate in wastewater should be removed to control eutrophication of water bodies. The potential of employing amorphous zirconium (Zr) hydroxide to remove phosphate from synthetic wastewater was studied in batch adsorption experiments and in a submerged membrane filtration adsorption hybrid (MFAH) reactor. The adsorption data satisfactorily fitted to Langmuir, pseudo-first order and pseudo-second order models. Langmuir adsorption maxima at 22 °C and pHs of 4.0, 7.1, and 10.0 were 30.40, 18.50, and 19.60 mg P/g, respectively. At pH 7.1 and temperatures of 40 °C and 60 °C, they were 43.80 and 54.60 mg P/g, respectively. The thermodynamic parameters, ΔG° and ΔS° were negative and ΔH° was positive. FTIR, zeta potential and competitive phosphate, sulphate and nitrate adsorption data showed that the mechanism of phosphate adsorption was inner-sphere complexation. In the submerged MFAH reactor experiment, when Zr hydroxide was added at doses of 1-5 g/L once only at the start of the experiment, the removal of phosphate from 3 L of wastewater containing 10 mg P/L declined after 5 h of operation. However, when Zr hydroxide was repeatedly added at 5 g/L dose every 24 h, satisfactory removal of phosphate was maintained for 3 days. PMID:26686069

  14. Equilibrium and kinetic data and process design for adsorption of Congo Red onto bentonite.

    PubMed

    Bulut, Emrah; Ozacar, Mahmut; Sengil, I Ayhan

    2008-06-15

    The adsorption of Congo Red onto bentonite in a batch adsorber has been studied. Four kinetic models, the pseudo first- and second-order equations, the Elovich equation and the intraparticle diffusion equation, were selected to follow the adsorption process. Kinetic parameters; rate constants, equilibrium adsorption capacities and correlation coefficients, for each kinetic equation were calculated and discussed. It was shown that the adsorption of Congo Red onto bentonite could be described by the pseudo second-order equation. The experimental isotherm data were analyzed using the Langmuir, Freundlich and Temkin equations. Adsorption of Congo Red onto bentonite followed the Langmuir isotherm. A single stage batch adsorber was designed for different adsorbent mass/treated effluent volume ratios using the Langmuir isotherm. PMID:18055111

  15. Study of enzyme adsorption and reaction kinetics for cellulose hydrolysis

    SciTech Connect

    Gilbert, I.G.

    1982-01-01

    Enzymatic hydrolysis of cellulose occurs due to the combined catalytic action of two types of cellulase components commonly referred to as C/sub 1/ and C/sub x/. However, before the hydrolysis reaction can begin, it is necessary for these enzymes to first adsorb onto the accessible surfaces of the insoluble cellulose substrate. The objective of the study was to gain a better understanding of the relationships between the adsorption of these enzyme components, the hydrolysis kinetics, the cellulosic surface area accessible to the enzymes, and the cellulose crystallinity. These relationships were investigated by passing a Trichoderma viride cellulase solution through columns of cellulose powder having different accessibility and crystallinity, and then analyzing the quantities of the different enzyme components and the hydrolysis product in the effluent. The amounts of the different cellulase components were analyzed using high-performance anion-exchange chromatography. Additional adsorption and hydrolysis experiments were done using columns of cellulose beads specially developed to provide amodel substrate for this analysis. A mathematical model has been formulated to describe the kinetics of enzyme adsorption and the resultant, initial hydrolysis rate in cellulose column. The analytical solutions obtained have been linearized into a convenient form so that the kinetic parameters of the model can be readily determined from experimental breakthrough curves.

  16. Batch and continuous flow studies of adsorptive removal of Cr(VI) by adapted bacterial consortia immobilized in alginate beads.

    PubMed

    Samuel, Jastin; Pulimi, Mrudula; Paul, Madona L; Maurya, Arun; Chandrasekaran, Natarajan; Mukherjee, Amitava

    2013-01-01

    The adsorptive removal of Cr(VI) by alginate beads containing Cr(VI)-adapted Acinetobacter junii, Escherichia coli and Bacillus subtilis in batch and continuous packed bed column reactors was investigated. Under optimized conditions (pH 3.0; contact time, 180 min; 30 °C; initial Cr(VI) concentration of 100 mg/L), 65.86 mg/g adsorption capacity was recorded in the batch study. When an adsorbent dosage of 1g/L, a flow rate of 5 mL/min, a bed height of 20 cm, an initial Cr(VI) concentration of 300 mg/L was employed, a capacity of 657 mg/g was noted for the continuous column assay. The batch sorption data followed the Langmuir isotherm and pseudo second order kinetics. Five sorption/desorption cycles yielded 100%, 99.63%, 95.31%, 80.7% and 74.22% regeneration, respectively. Cr(VI) adsorption studies using spiked ground water, freshwater and domestic wastewater in a packed bed reactor demonstrated Cr(VI) removals of 64.8%, 55.08%, 56.86% respectively. Cr(VI) sorption on immobilized bacteria was confirmed with Fourier-transform infrared and Energy dispersive X-ray spectroscopy. PMID:23201524

  17. A comparative adsorption study: 17β-estradiol onto aerobic granular sludge and activated sludge.

    PubMed

    Zheng, Xiao-ying; He, Yu-jie; Chen, Wei; Wang, Ming-yang; Cao, Su-lan; Ni, Ming; Chen, Yu

    2016-01-01

    Adsorption plays a significant role in removing hydrophobic 17β-estradiol (E2) from wastewater. Batch experiments were conducted to compare the adsorption of E2 onto activated aerobic granular sludge (AGS) and activated sludge (AS), and features evaluated included the adsorption kinetics, thermodynamics, and influence of other environmental factors. By using a non-chemical wet-heat technique, both AGS and AS were treated to inactivated status. Then, after loading E2, the adsorption equilibrium capacity of the AGS was found to be greater than that of the AS at the same initial concentration of E2. Moreover, both the adsorption processes corresponded to a pseudo-second-order kinetic model; the adsorption rate constant of AGS was found to be higher and the half-adsorption time was shorter than that of AS. Next, evaluations of adsorption isotherms and thermodynamics indicated that the adsorption process was mainly a physical process. Lower temperatures facilitated a higher equilibrium adsorption capacity. However, the adsorption binding sites of AGS were distributed more uniformly at higher temperature, in contrast to the distribution found for AS. Finally, acidic conditions and an appropriate ionic strength (0.4 mol/L) were found to be particularly conducive to the adsorption process. Overall, the results showed that AGS has the potential to adsorb E2 with significant efficiency, thereby offering a new and more efficient means of treating E2 and trace oestrogens in wastewater.

  18. Binding of Cu(II) ions to peptides studied by fluorescence spectroscopy and isothermal titration calorimetry

    NASA Astrophysics Data System (ADS)

    Makowska, Joanna; Żamojć, Krzysztof; Wyrzykowski, Dariusz; Uber, Dorota; Wierzbicka, Małgorzata; Wiczk, Wiesław; Chmurzyński, Lech

    2016-01-01

    Steady-state and time-resolved fluorescence quenching measurements supported by Isothermal Titration Calorimetry (ITC) were used to study the interactions of Cu2 + with four peptides. Two of them were taken from the N-terminal part of the FBP28 protein (formin binding protein) WW domain: Tyr-Lys-Thr-Ala-Asp-Gly-Lys-Thr-Tyr-NH2 (D9) and its mutant Tyr-Lys-Thr-Ala-Asn-Gly-Lys-Thr-Tyr-NH2 (D9_M) as well as two mutated peptides from the B3 domain of the immunoglobulin binding protein G derived from Streptococcus: Asp-Val-Ala-Thr-Tyr-Thr-NH2 (J1) and Glu-Val-Ala-Thr-Tyr-Thr-NH2 (J2). The measurements were carried out at 298.15 K in 20 mM 2-(N-morpholino)ethanesulfonic acid (MES) buffer solution with a pH of 6. The fluorescence of all peptides was quenched by Cu2 + ions. The stoichiometry, conditional stability constants and thermodynamic parameters for the interactions of the Cu2 + ions with D9 and D9_M were determined from the calorimetric data. The values of the conditional stability constants were additionally determined from fluorescence quenching measurements and compared with those obtained from calorimetric studies. There was a good correlation between data obtained from the two techniques. On the other hand, the studies revealed that J1 and J2 do not exhibit an affinity towards metal ions. The obtained results prove that fluorescence quenching experiments may be successfully used in order to determine stability constants of complexes with fluorescent ligands. Finally, based on the obtained results, the coordinating properties of the peptides towards the Cu2 + ions are discussed.

  19. Binding of Cu(II) ions to peptides studied by fluorescence spectroscopy and isothermal titration calorimetry.

    PubMed

    Makowska, Joanna; Żamojć, Krzysztof; Wyrzykowski, Dariusz; Uber, Dorota; Wierzbicka, Małgorzata; Wiczk, Wiesław; Chmurzyński, Lech

    2016-01-15

    Steady-state and time-resolved fluorescence quenching measurements supported by Isothermal Titration Calorimetry (ITC) were used to study the interactions of Cu(2+) with four peptides. Two of them were taken from the N-terminal part of the FBP28 protein (formin binding protein) WW domain: Tyr-Lys-Thr-Ala-Asp-Gly-Lys-Thr-Tyr-NH2 (D9) and its mutant Tyr-Lys-Thr-Ala-Asn-Gly-Lys-Thr-Tyr-NH2 (D9_M) as well as two mutated peptides from the B3 domain of the immunoglobulin binding protein G derived from Streptococcus: Asp-Val-Ala-Thr-Tyr-Thr-NH2 (J1) and Glu-Val-Ala-Thr-Tyr-Thr-NH2 (J2). The measurements were carried out at 298.15K in 20mM 2-(N-morpholino)ethanesulfonic acid (MES) buffer solution with a pH of 6. The fluorescence of all peptides was quenched by Cu(2+) ions. The stoichiometry, conditional stability constants and thermodynamic parameters for the interactions of the Cu(2+) ions with D9 and D9_M were determined from the calorimetric data. The values of the conditional stability constants were additionally determined from fluorescence quenching measurements and compared with those obtained from calorimetric studies. There was a good correlation between data obtained from the two techniques. On the other hand, the studies revealed that J1 and J2 do not exhibit an affinity towards metal ions. The obtained results prove that fluorescence quenching experiments may be successfully used in order to determine stability constants of complexes with fluorescent ligands. Finally, based on the obtained results, the coordinating properties of the peptides towards the Cu(2+) ions are discussed.

  20. Binding of Cu(II) ions to peptides studied by fluorescence spectroscopy and isothermal titration calorimetry.

    PubMed

    Makowska, Joanna; Żamojć, Krzysztof; Wyrzykowski, Dariusz; Uber, Dorota; Wierzbicka, Małgorzata; Wiczk, Wiesław; Chmurzyński, Lech

    2016-01-15

    Steady-state and time-resolved fluorescence quenching measurements supported by Isothermal Titration Calorimetry (ITC) were used to study the interactions of Cu(2+) with four peptides. Two of them were taken from the N-terminal part of the FBP28 protein (formin binding protein) WW domain: Tyr-Lys-Thr-Ala-Asp-Gly-Lys-Thr-Tyr-NH2 (D9) and its mutant Tyr-Lys-Thr-Ala-Asn-Gly-Lys-Thr-Tyr-NH2 (D9_M) as well as two mutated peptides from the B3 domain of the immunoglobulin binding protein G derived from Streptococcus: Asp-Val-Ala-Thr-Tyr-Thr-NH2 (J1) and Glu-Val-Ala-Thr-Tyr-Thr-NH2 (J2). The measurements were carried out at 298.15K in 20mM 2-(N-morpholino)ethanesulfonic acid (MES) buffer solution with a pH of 6. The fluorescence of all peptides was quenched by Cu(2+) ions. The stoichiometry, conditional stability constants and thermodynamic parameters for the interactions of the Cu(2+) ions with D9 and D9_M were determined from the calorimetric data. The values of the conditional stability constants were additionally determined from fluorescence quenching measurements and compared with those obtained from calorimetric studies. There was a good correlation between data obtained from the two techniques. On the other hand, the studies revealed that J1 and J2 do not exhibit an affinity towards metal ions. The obtained results prove that fluorescence quenching experiments may be successfully used in order to determine stability constants of complexes with fluorescent ligands. Finally, based on the obtained results, the coordinating properties of the peptides towards the Cu(2+) ions are discussed. PMID:26363471

  1. Modeling high adsorption capacity and kinetics of organic macromolecules on super-powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Ando, Naoya; Yoshida, Tomoaki; Kurotobi, Ryuji; Matsushita, Taku; Ohno, Koichi

    2011-02-01

    The capacity to adsorb natural organic matter (NOM) and polystyrene sulfonates (PSSs) on small particle-size activated carbon (super-powdered activated carbon, SPAC) is higher than that on larger particle-size activated carbon (powdered-activated carbon, PAC). Increased adsorption capacity is likely attributable to the larger external surface area because the NOM and PSS molecules do not completely penetrate the adsorbent particle; they preferentially adsorb near the outer surface of the particle. In this study, we propose a new isotherm equation, the Shell Adsorption Model (SAM), to explain the higher adsorption capacity on smaller adsorbent particles and to describe quantitatively adsorption isotherms of activated carbons of different particle sizes: PAC and SPAC. The SAM was verified with the experimental data of PSS adsorption kinetics as well as equilibrium. SAM successfully characterized PSS adsorption isotherm data for SPACs and PAC simultaneously with the same model parameters. When SAM was incorporated into an adsorption kinetic model, kinetic decay curves for PSSs adsorbing onto activated carbons of different particle sizes could be simultaneously described with a single kinetics parameter value. On the other hand, when SAM was not incorporated into such an adsorption kinetic model and instead isotherms were described by the Freundlich model, the kinetic decay curves were not well described. The success of the SAM further supports the adsorption mechanism of PSSs preferentially adsorbing near the outer surface of activated carbon particles. PMID:21172719

  2. Adsorption of n-pentane on mesoporous silica and adsorbent deformation.

    PubMed

    Gor, Gennady Yu; Paris, Oskar; Prass, Johannes; Russo, Patrícia A; Ribeiro Carrott, M Manuela L; Neimark, Alexander V

    2013-07-01

    Development of quantitative theory of adsorption-induced deformation is important, e.g., for enhanced coalbed methane recovery by CO2 injection. It is also promising for the interpretation of experimental measurements of elastic properties of porous solids. We study deformation of mesoporous silica by n-pentane adsorption. The shape of experimental strain isotherms for this system differs from the shape predicted by thermodynamic theory of adsorption-induced deformation. We show that this difference can be attributed to the difference of disjoining pressure isotherm, responsible for the solid-fluid interactions. We suggest the disjoining pressure isotherm suitable for n-pentane adsorption on silica and derive the parameters for this isotherm from experimental data of n-pentane adsorption on nonporous silica. We use this isotherm in the formalism of macroscopic theory of adsorption-induced deformation of mesoporous materials, thus extending this theory for the case of weak solid-fluid interactions. We employ the extended theory to calculate solvation pressure and strain isotherms for SBA-15 and MCM-41 silica and compare it with experimental data obtained from small-angle X-ray scattering. Theoretical predictions for MCM-41 are in good agreement with the experiment, but for SBA-15 they are only qualitative. This deviation suggests that the elastic modulus of SBA-15 may change during pore filling.

  3. Kinetic and equilibrium studies on the removal of acid dyes from aqueous solutions by adsorption onto activated carbon cloth.

    PubMed

    Hoda, Numan; Bayram, Edip; Ayranci, Erol

    2006-09-01

    Removal of acid dyes Acid Blue 45, Acid Blue 92, Acid Blue 120 and Acid Blue 129 from aqueous solutions by adsorption onto high area activated carbon cloth (ACC) was investigated. Kinetics of adsorption was followed by in situ UV-spectroscopy and the data were treated according to pseudo-first-order, pseudo-second-order and intraparticle diffusion models. It was found that the adsorption process of these dyes onto ACC follows the pseudo-second-order model. Adsorption isotherms were derived at 25 degrees C on the basis of batch analysis. Isotherm data were treated according to Langmuir and Freundlich models. The fits of experimental data to these equations were examined. PMID:16563617

  4. Study On Adsorption of Bromate From Aqueous Solution On Modified Activated Carbon

    NASA Astrophysics Data System (ADS)

    Liu, Tong-mian; Cui, Fu-yi; Zhao, Zhi-wei; Liu, Dong-mei; Zhu, Qi; Wang, Huan

    2010-11-01

    A coal-based activated carbon was treated chemically with nitric acid, sodium hydroxide and ammonia for its surface modification, and its adsorption capacity was investigated with bromate. Several techniques were used to characterize the physicochemical properties of these materials including BET, XPS, pHpzc and Boehm titration. The results indicated that the specific surface area of the activated carbon decreased after oxidation with nitric acid. But the amount of surface acidic oxygen-containing functional groups of the oxidized sample increased compared to the raw carbon and the points of zero charge (pHpzc) decreased. The specific surface area of the activated carbon also decreased after sodium hydroxide treatment and the points of zero charge increased. The changes of surface chemical properties after the ammonia treatment was opposite to the oxidized sample. As a result, the pHpzc of the carbon was increased to near pH9.3, the amount of surface basic groups was increased. Furthermore, the data of bromate adsorption on all the samples were fitted to the Langmuir isotherm model well which indicates monolayer adsorption. In addition, the adsorption capacity of ammonia treatment sample was the highest and its saturated adsorption capacity reached 1.55 mg/g. A strong correlation was found between basic groups and adsorption capacity of bromate. Enhancement of basic groups was favorable for bromate removal.

  5. Human serum albumin adsorption study on 62-MHz miniaturized quartz gravimetric sensors.

    PubMed

    Kao, Ping; Patwardhan, Ashish; Allara, David; Tadigadapa, Srinivas

    2008-08-01

    We have designed and fabricated 25-microm-thick quartz resonators operating at a fundamental resonance frequency of approximately 62 MHz. The results show a substantial increase in the mass sensitivity compared to single monolithic commercial resonators operating at lower frequencies in the approximately 5-10-MHz range. The overall performance of the micromachined resonators is demonstrated for the example of human serum albumin protein adsorption from aqueous buffer solutions onto gold electrodes functionalized with self-assembled monolayers. The results show a saturation adsorption frequency change of 6.8 kHz as opposed to 40 Hz for a commercial approximately 5-MHz sensor under identical loading conditions. From the analysis of the adsorption isotherm, the equilibrium adsorption constant of the adsorption of the protein layer was found to be K = 8.03 x 10(6) M(-1), which is in agreement with the values reported in the literature. The high sensitivity of the miniaturized QCM devices can be a significant advantage in both vapor and solution adsorption analyses.

  6. Experimental and Quantum Studies on Adsorption and Corrosion Inhibition Effect of Imidazole Derivatives on N80 Steel in Hydrochloric Acid

    NASA Astrophysics Data System (ADS)

    Yadav, M.; Kumar, Sumit; Sharma, Dipti; Yadav, P. N.

    2013-12-01

    The inhibition effect of synthesized N‧-(phenylmethylidene)-2-(2-methyl-1H-benzimidazol-1-yl)acetohydrazides, N‧-(4-methylphenylmethylidene)-2-(2-methyl-1H-benzimidazol-1-yl)acetohydrazides, and N‧-(4-methoxyphenylmethylidene)-2-(2-methyl-1H-benzimidazol-1-yl)acetohydrazides on the corrosion behaviour of N80 steel in 15% hydrochloric acid solution was investigated using weight loss, potentiostatic polarization and electrochemical impedance spectroscopy methods. The inhibition efficiency increased as the concentration of the inhibitors was increased. The effect of temperature on corrosion inhibition was investigated by weight loss method and thermodynamic parameters were calculated. Potentiodynamic polarization measurements show that all the three studied inhibitors act as mixed inhibitor. The adsorption of inhibitors on N80 steel surface obeys Langmuir adsorption isotherm. The structure of inhibitors was optimized using semiemperical AM1 method. Theoretical parameters such as the highest occupied molecular orbital (EHOMO), lowest unoccupied molecular orbital (ELUMO) energy levels, energy gap (ΔE = ELUMO - EHOMO), dipole moment (μ), global hardness (γ), softness (σ), binding energy, molecular surface area and the fraction of electrons transferred (ΔN) were calculated and the adsorption mechanism was discussed. Scanning electron microscopy was used to characterize the surface marphology of the N80 steel.

  7. Adsorption of dissolved Reactive red dye from aqueous phase onto activated carbon prepared from agricultural waste.

    PubMed

    Senthilkumaar, S; Kalaamani, P; Porkodi, K; Varadarajan, P R; Subburaam, C V

    2006-09-01

    The adsorption of Reactive red dye (RR) onto Coconut tree flower carbon (CFC) and Jute fibre carbon (JFC) from aqueous solution was investigated. Adsorption studies were carried out at different initial dye concentrations, initial solution pH and adsorbent doses. The kinetic studies were also conducted; the adsorption of Reactive red onto CFC and JFC followed pseudosecond-order rate equation. The effective diffusion coefficient was evaluated to establish the film diffusion mechanism. Quantitative removal of Reactive red dye was achieved at strongly acidic conditions for both the carbons studied. The adsorption isotherm data were fitted well to Langmuir isotherm and the adsorption capacity were found to be 181.9 and 200 mg/g for CFC and JFC, respectively. The overall rate of dye adsorption appeared to be controlled by chemisorption, in this case in accordance with poor desorption studies.

  8. Preparation of char from lotus seed biomass and the exploration of its dye removal capacity through batch and column adsorption studies.

    PubMed

    Nethaji, S; Sivasamy, A; Kumar, R Vimal; Mandal, A B

    2013-06-01

    Char was obtained from lotus seed biomass by a simple single-step acid treatment process. It was used as an adsorbent for the removal of malachite green dye (MG) from simulated dye bath effluent. The adsorbent was characterized for its surface morphology, surface functionalities, and zero point charge. Batch studies were carried out by varying the parameters such as initial aqueous pH, adsorbent dosage, adsorbent particle size, and initial adsorbate concentration. Langmuir and Freundlich isotherms were used to test the isotherm data and the Freundlich isotherm best fitted the data. Thermodynamic studies were carried out and the thermodynamic parameters such as ∆G, ∆H, and ∆S were evaluated. Adsorption kinetics was carried out and the data were tested with pseudofirst-order model, pseudosecond-order model, and intraparticle diffusion model. Adsorption of MG was not solely by intraparticle diffusion but film diffusion also played a major role. Continuous column experiments were also conducted using microcolumn and the spent adsorbent was regenerated using ethanol and was repeatedly used for three cycles in the column to determine the reusability of the regenerated adsorbent. The column data were modeled with the modeling equations such as Adam-Bohart model, Bed Depth Service Time (BDST) model, and Yoon-Nelson model for all the three cycles.

  9. A novel zerovalent manganese for removal of copper ions: synthesis, characterization and adsorption studies

    NASA Astrophysics Data System (ADS)

    Dada, A. O.; Adekola, F. A.; Odebunmi, E. O.

    2015-11-01

    Synthesis of nanoscale zerovalent manganese (nZVMn) by chemical reduction was carried out in a single pot system under inert environment. nZVMn was characterized using a combination of analytical techniques: Ultraviolet-Visible Spectroscopy, Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, Transmission Electron Microscopy, Energy Dispersive X-ray, BET surface area and Point of Zero Charge. The adsorption physicochemical factors: pH, contact time, adsorbent dose, agitation speed, initial copper ion concentration and temperature were optimized. The kinetic data fitted better to Pseudo second-order, Elovich, fractional power and intraparticle diffusion models and their validity was tested by three statistical models: sum of square error, Chi-square (χ 2) and normalized standard deviation (Δq). Seven of the two-parameter isotherm models [Freundlich, Langmuir, Temkin, Dubinin-Kaganer-Raduskevich (DKR), Halsey, Harkin-Jura and Flory-Huggins] were used to analyse the equilibrium adsorption data. The Langmuir monolayer adsorption capacity (Q max = 181.818 mg/g) obtained is greater than other those of nano-adsorbents utilized in adsorption of copper ions. The equilibrium adsorption data were better described by Langmuir, Freundlich, Temkin, DKR and Halsey isotherm models considering their coefficient of regression (R 2 > 0.90). The values of the thermodynamic parameters: standard enthalpy change ∆H° (+50.27848 kJ mol-1), standard entropy change ∆S° (203.5724 J mol-1 K-1) and the Gibbs free energy change ∆G° revealed that the adsorption process was feasible, spontaneous, and endothermic in nature. The performance of this novel nanoscale zerovalent manganese (nZVMn) suggested that it has a great potential for effective removal of copper ions from aqueous solution.

  10. Experimental and theoretical studies of isothermal upward gas-liquid flows in vertical tubes

    SciTech Connect

    Fernandes, R.C.

    1981-01-01

    In two-phase flow technolgy, two important problems exist which must be solved as a function of the various physical and system parameters associated with the phenomenon, and which stand as prerequisites for proper modelling of two-phase processes: Prediction of the flow pattern under existing operating conditions and prediction of the holdup for each given flow pattern. Modelling studies of steady isothermal upward gas-liquid flows in vertical pipes, at low pressures, were undertaken. Experimental data on liquid holdup over a wide range of flow rates were taken for all observed flow patterns-bubbly, slug, churn, and annular - by means of a specially designed Quick-Closing Valves System. This technique also allowed the detection of a unique phenomenon occurring in the form of fast-flowing slugs of gas-liquid mixture, in both the churn and annular flow patterns, which was called the lump phenomenon. The lump holdup was measured and a qualitative theory regarding the nature, formation and propagation of these structures was proposed. A photographic method was applied to the slug flow pattern in order to determine both the rise velocity and length of Taylor bubbles and liquid slugs characteristic of this flow regime. Assisted by the measured data, flow pattern-based physical models were developed for predicting holdup of bubbly flows and the detailed structure of slug flows. The latter was accomplished by means of a fairly complete analysis which enabled the prediction of several variables of interest such as void fractions, velocities, film thicknesses and the length ratio between Taylor bubbles and liquid slugs. The average holdup for churn flow was predicted by directly applying the slug flow model to that flow pattern. A simplified framework for calculating the holdup in annular flows was also proposed. The comparison between theory and experiment showed that for bubbly, slug and churn flows the predicted results are in good agreement with the data.

  11. Study on an effective industrial waste-based adsorbent for the adsorptive removal of phosphorus from wastewater: equilibrium and kinetics studies.

    PubMed

    Xie, Ruzhen; Chen, Yao; Cheng, Ting; Lai, Yuguo; Jiang, Wenju; Yang, Zhishan

    2016-01-01

    In this work, an effective adsorbent for removing phosphate from aqueous solution was developed from modifying industrial waste--lithium silica fume (LSF). The characterization of LSF before and after modification was investigated using an N2 adsorption-desorption technique (Brunauer-Emmett-Teller, BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Studies were conducted to investigate the effect of adsorbent dose, initial solution pH, contact time, phosphate concentration, and temperature on phosphate removal using this novel adsorbent. The specific surface area for modified LSF (LLSF) is 24.4024 m(2)/g, improved 69.8% compared with unmodified LSF. XRD result suggests that the lanthanum phosphate complex was formed on the surface of LLSF. The maximum phosphate adsorption capacity was 24.096 mg P/g for LLSF, and phosphate removal was favored in the pH range of 3-8. The kinetic data fitted pseudo-second-order kinetic equation, intra-particle diffusion was not the only rate controlling step. The adsorption isotherm results illustrated that the Langmuir model provided the best fit for the equilibrium data. The change in free energy (△G(0)), enthalpy (△H(0)) and entropy (△S(0)) revealed that the adsorption of phosphate on LLSF was spontaneous and endothermic. It was concluded that by modifying with lanthanum, LSF can be turned to be a highly efficient adsorbent in phosphate removal.

  12. Study on an effective industrial waste-based adsorbent for the adsorptive removal of phosphorus from wastewater: equilibrium and kinetics studies.

    PubMed

    Xie, Ruzhen; Chen, Yao; Cheng, Ting; Lai, Yuguo; Jiang, Wenju; Yang, Zhishan

    2016-01-01

    In this work, an effective adsorbent for removing phosphate from aqueous solution was developed from modifying industrial waste--lithium silica fume (LSF). The characterization of LSF before and after modification was investigated using an N2 adsorption-desorption technique (Brunauer-Emmett-Teller, BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Studies were conducted to investigate the effect of adsorbent dose, initial solution pH, contact time, phosphate concentration, and temperature on phosphate removal using this novel adsorbent. The specific surface area for modified LSF (LLSF) is 24.4024 m(2)/g, improved 69.8% compared with unmodified LSF. XRD result suggests that the lanthanum phosphate complex was formed on the surface of LLSF. The maximum phosphate adsorption capacity was 24.096 mg P/g for LLSF, and phosphate removal was favored in the pH range of 3-8. The kinetic data fitted pseudo-second-order kinetic equation, intra-particle diffusion was not the only rate controlling step. The adsorption isotherm results illustrated that the Langmuir model provided the best fit for the equilibrium data. The change in free energy (△G(0)), enthalpy (△H(0)) and entropy (△S(0)) revealed that the adsorption of phosphate on LLSF was spontaneous and endothermic. It was concluded that by modifying with lanthanum, LSF can be turned to be a highly efficient adsorbent in phosphate removal. PMID:27120644

  13. Adsorption of phthalic acid esters (PAEs) by amphiphilic polypropylene nonwoven from aqueous solution: the study of hydrophilic and hydrophobic microdomain.

    PubMed

    Zhou, Xiangyu; Wei, Junfu; Zhang, Huan; Liu, Kai; Wang, Han

    2014-05-30

    A kind of amphiphilic polypropylene nonwoven with hydrophilic and hydrophobic microdomain was prepared through electron beam induced graft polymerization and subsequent ring opening reaction and then utilized in the adsorption of phthalic acid esters (PAEs). To elucidate the superiority of such amphiphilic microdomain, a unique structure without hydrophilic part was constructed as comparison. In addition, the adsorption behaviors including adsorption kinetics, isotherms and pH effect were systematically investigated. The result indicated that the amphiphilic structure and the synergy between hydrophilic and hydrophobic microdomain could considerably improve the adsorption capacities, rate and affinity. Particularly the existence of hydrophilic microdomain could reduce the diffusion resistance and energy barrier in the adsorption process. These adsorption results showed that the amphiphilic PP nonwoven have the potential to be used in environmental application.

  14. Adsorption of cellulase from Trichoderma viride on cellulose

    SciTech Connect

    Ooshima, H.; Sakata, M.; Harano, Y.

    1983-12-01

    The adsorption of cellulase from Trichoderma viride (Meicelase CEP) on the surface of pure cellulose was studied. The adsorption was found to obey apparently the Langmuir isotherm. From the data concerning the effects of temperature and the crystallinity of cellulose on the Langmuir adsorption parameters, the characteristics of the adsorption of the individual cellulase components, namely CMCase (endoglucanase) and Avicelase (exoglucanase), were discussed. While beta-glucosidase also adsorbed on the surface of cellulose at 5 degrees C, it did not at 50 degrees C. (Refs. 27).

  15. Study of Gas Adsorption on Biphasic Nanostructured Surfaces

    NASA Astrophysics Data System (ADS)

    Nader, Rami; Hamieh, Tayssir; Villieras, Frédéric; Angelina. Razafitianamaharav; Toufaily, Joumana; Mcheik, Ali S.; Thomas, Fabien

    This work has carried out on grafted nanoparticles oxide silica to determine the possible existence of "nanoeffect". The textural properties and heterogeneity of surface of the samples were studied at the interface solid-gas. The Geometric properties were discussed in terms of the surface area while the energy properties were discussed in terms of the reactive sites of the surface.In the framework of this study, firstly, the sample was used in the non-grafted state and then in the grafted state using a hydrophilic molecule and a hydrophobic molecule. Several techniques have been used: Infrared spectroscopy, X ray diffraction, the point by point volumetric technique, which enable us to study the interactions between the adsorbate and the solid surface. Finally we have determined the size and electro thermal mobility using zestasizer (Nano ZS). The results obtained show that there are two types of groups silanols and siloxanes on the silica OX5 giving a composite hydrophilic-hydrophobic. This character causes a singular behavior in adsorptive material, the presence of hydrophilic groups, strongly polarized, and is detected by infrared spectroscopy. These groups cause significant differences depending on the polarizability of the probe molecules, and the adsorption of argon shows no heterogeneity of the surface, while nitrogen is adsorbed on the polar sites at low relative pressure, While the volumetric continues to adsorption of argon and nitrogen on combustion silica to obtain and to highlight sites of high energy and polar surface sites. The combustion silica which has been used as adsorbent in this study has an amorphous surface, virtually free of impurities indicates that the sample is not micro porous and grafting of the molecules makes a decrease in high energy sites or to a relative increase in surface low energy.

  16. Adsorption of imidazole on Au(111) surface: Dispersion corrected density functional study

    NASA Astrophysics Data System (ADS)

    Izzaouihda, Safia; Mahjoubi, Khaled; Abou El Makarim, Hassna; Komiha, Najia; Benoit, David M.

    2016-10-01

    We use density functional theory in the generalized gradient approximation to study the adsorption of imidazole on the Au(111) surface and account for dispersion effect using Grimme's empirical dispersion correction technique. Our results show that the adsorption energy of imidazole depends on the slab size and on the adsorption site. In agreement with other studies, we find the largest adsorption energy for imidazole on a top site of Au(111). However, we also note that the adsorption energy at other sites is substantial.

  17. Interaction of hydrogen chloride with alumina. [influence of outgas and temperature conditions on adsorption

    NASA Technical Reports Server (NTRS)

    Bailey, R. R.; Wightman, J. P.

    1975-01-01

    The influence of outgas conditions and temperature on the adsorptive properties of two aluminas Alon-c and Al6sG were studied using adsorption isotherm measurements. Alon-C and Al6SG were characterized using X-ray powder diffraction, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and BET nitrogen surface areas. Some of these techniques were applied to two other aluminas but no isotherm data was obtained. Isotherm data and techniques applied to each alumina are summarized in tabular form.

  18. Equilibrium, kinetic and thermodynamic studies on the adsorption of phenol onto graphene

    SciTech Connect

    Li, Yanhui; Du, Qiuju; Liu, Tonghao; Sun, Jiankun; Jiao, Yuqin; Xia, Yanzhi; Xia, Linhua; Wang, Zonghua; Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai

    2012-08-15

    Graphical abstract: The effect of temperature on phenol adsorbed by graphene shows that the equilibrium adsorption capacity of phenol increases with the increase in temperature from 285 to 333 K. Increasing adsorption capacities with temperature indicates that the adsorption of phenol is controlled by an endothermic reaction. Highlights: ► The graphene has high phenol adsorption capacity. ► The graphene has a high specific surface area of 305 m{sup 2}/g. ► The adsorption capacity is high at acidic pH range. ► The graphene has rapid phenol adsorption rate. ► Phenol adsorption is a spontaneous and endothermic process. -- Abstract: Graphene, a new member of carbon family, has been prepared, characterized and used as adsorbent to remove phenol from aqueous solution. The effect parameters including pH, dosage, contact time, and temperature on the adsorption properties of phenol onto graphene were investigated. The results showed that the maximum adsorption capacity can reach 28.26 mg/g at the conditions of initial phenol concentration of 50 mg/L, pH 6.3 and 285 K. Adsorption data were well described by both Freundlich and Langmuir models. The kinetic study illustrated that the adsorption of phenol onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of phenol onto graphene was endothermic and spontaneous.

  19. Ethanol adsorption on the Si (111) surface: First principles study

    NASA Astrophysics Data System (ADS)

    Gavrilenko, Alexander V.; Bonner, Carl E.; Gavrilenko, Vladimir I.

    2012-03-01

    Equilibrium atomic configurations and electron energy structure of ethanol adsorbed on the Si (111) surface are studied by the first principles density functional theory. Geometry optimization is performed by the total energy minimization method. Equilibrium atomic geometries of ethanol, both undissociated and dissociated, on the Si (111) surface are found and analysed. Reaction pathways and predicted transition states are discussed in comparison with available experimental data in terms of the feasibility of the reactions occurring. Analysis of atom and orbital resolved projected density of states indicates substantial modifications of the Si surface valence and conduction electron bands due to the adsorption of ethanol affecting the electronic properties of the surface.

  20. A study of the kinetics of isothermal nicotine desorption from silicon dioxide

    NASA Astrophysics Data System (ADS)

    Adnadjevic, Borivoj; Lazarevic, Natasa; Jovanovic, Jelena

    2010-12-01

    The isothermal kinetics of nicotine desorption from silicon dioxide (SiO 2) was investigated. The isothermal thermogravimetric curves of nicotine at temperatures of 115 °C, 130 °C and 152 °C were recorded. The kinetic parameters ( Ea, ln A) of desorption of nicotine were calculated using various methods (stationary point, model constants and differential isoconversion method). By applying the "model-fitting" method, it was found that the kinetic model of nicotine desorption from silicon dioxide was a phase boundary controlled reaction (contracting volume). The values of the kinetic parameters, Ea,α and ln Aα, complexly change with changing degree of desorption and a compensation effect exists. A new mechanism of activation for the desorption of the absorbed molecules of nicotine was suggested in agreement with model of selective energy transfer.

  1. Integration and global analysis of isothermal titration calorimetry data for studying macromolecular interactions.

    PubMed

    Brautigam, Chad A; Zhao, Huaying; Vargas, Carolyn; Keller, Sandro; Schuck, Peter

    2016-05-01

    Isothermal titration calorimetry (ITC) is a powerful and widely used method to measure the energetics of macromolecular interactions by recording a thermogram of differential heating power during a titration. However, traditional ITC analysis is limited by stochastic thermogram noise and by the limited information content of a single titration experiment. Here we present a protocol for bias-free thermogram integration based on automated shape analysis of the injection peaks, followed by combination of isotherms from different calorimetric titration experiments into a global analysis, statistical analysis of binding parameters and graphical presentation of the results. This is performed using the integrated public-domain software packages NITPIC, SEDPHAT and GUSSI. The recently developed low-noise thermogram integration approach and global analysis allow for more precise parameter estimates and more reliable quantification of multisite and multicomponent cooperative and competitive interactions. Titration experiments typically take 1-2.5 h each, and global analysis usually takes 10-20 min.

  2. Non-Isothermal Calorimetric Studies of the Crystallization of Lithium Disilicate Glass

    NASA Technical Reports Server (NTRS)

    Ray, C. S.; Day, D. E.; Huang, W.; Narayan, K. Lakshmi; Cull, T. S.; Kelton, K. F.

    1996-01-01

    The influence of preannealing treatments on the polymorphic crystallization of lithium disilicate glasses is examined. As expected, glasses heated at different rates through the temperature range where there is significant nucleation develop widely different numbers of nuclei. This can dramatically influence the stability and transformation characteristics of the annealed glass. Non-isothermal differential scanning calorimetry (DSC) and differential thermal analysis (DTA) measurements are demonstrated to be useful to probe the nucleation behavior. The first systematic investigations of particle size effects on the non-isothermal transformation behavior are presented and discussed. Based on DTA and microscopy experiments, we show that small particles of lithium disilicate glasses crystallize primarily by surface crystallization. The relative importance of surface versus volume crystallization is examined by varying particle size, by introducing nucleating agents and by exposing glasses to atmospheres of different water content. These data are analyzed quantitatively using a numerical model developed in a second paper following in this volume.

  3. Competitive Adsorption Study of CO2 and SO2 on CoII3[CoIII(CN)6]2 Using DRIFTS

    SciTech Connect

    Windisch, Charles F.; Thallapally, Praveen K.; McGrail, B. Peter

    2010-09-15

    Diffuse reflectance infrared Fourier transform spectroscopy was used to study the competitive adsorption of CO2 and SO2 on the cobalt Prussian blue analogue CoII3[CoIII(CN)6]2 at 298 K. Characteristic peaks for adsorbed CO2 and SO2 species were identified and their relative areas, measured simultaneously as a function of pressure at 298 K, varied in accordance with a Langmuir-Freundlich isotherm fitted to both gases in the low-coverage Henry’s Law limit. Evidence for co-adsorption of trace water was also obtained, as well as the apparent formation of an analogous cobalt nitroprusside compound as a reaction product under certain conditions. The several aspects of the adsorption of CO2 and SO2 on CoCo determined in this work point to an important role for real-time diffuse reflectance infrared measurements in adsorption studies, particularly in the case of competitive adsorption where the occurrence and fate of molecular-level markers arising from more than one adsorbed species can be monitored simultaneously. Depending on the application, this may more than offset certain quantitative limitations of the technique that confine measurements to a relatively narrow set of experimental conditions and demand careful consideration of the effects of sample preparation and treatment.

  4. Adsorption efficiency of natural materials for low-concentration cesium in solution.

    PubMed

    Miura, A; Kubota, T; Hamada, K; Hitomi, T

    2016-01-01

    In this study, several natural materials were investigated in order to clarify their potential use as cesium (Cs) adsorbents in situ. Four materials--carbonized rice hull, beech sawdust, oak sawdust, and charcoal (Japanese cedar)--which were previously shown to have Cs adsorption capabilities, were examined. Cs adsorption experiments were conducted using different initial Cs and adsorbent concentrations. The physical properties, adsorption isotherms, and adsorption processes were then examined, so as to exploit the Cs adsorption characteristics in the field. Based on these findings, carbonized rice hull and beech sawdust were selected as effective Cs adsorbents. It was found that these materials show continuous and stable Cs adsorption rates for different initial Cs concentrations. The adsorption efficiency of these two adsorption materials in combination was considered, and it was shown that the adsorption isotherms for carbonized rice hull and beech sawdust follow the Freundlich model. Furthermore, the beech sawdust adsorption process exhibited better agreement with the calculated values obtained via the adsorption rate model and the adsorption kinetics model than did the carbonized rice hull adsorption.

  5. Adsorption efficiency of natural materials for low-concentration cesium in solution.

    PubMed

    Miura, A; Kubota, T; Hamada, K; Hitomi, T

    2016-01-01

    In this study, several natural materials were investigated in order to clarify their potential use as cesium (Cs) adsorbents in situ. Four materials--carbonized rice hull, beech sawdust, oak sawdust, and charcoal (Japanese cedar)--which were previously shown to have Cs adsorption capabilities, were examined. Cs adsorption experiments were conducted using different initial Cs and adsorbent concentrations. The physical properties, adsorption isotherms, and adsorption processes were then examined, so as to exploit the Cs adsorption characteristics in the field. Based on these findings, carbonized rice hull and beech sawdust were selected as effective Cs adsorbents. It was found that these materials show continuous and stable Cs adsorption rates for different initial Cs concentrations. The adsorption efficiency of these two adsorption materials in combination was considered, and it was shown that the adsorption isotherms for carbonized rice hull and beech sawdust follow the Freundlich model. Furthermore, the beech sawdust adsorption process exhibited better agreement with the calculated values obtained via the adsorption rate model and the adsorption kinetics model than did the carbonized rice hull adsorption. PMID:27191567

  6. Removal of Cu²⁺ from aqueous solutions by the novel modified bagasse pulp cellulose: Kinetics, isotherm and mechanism.

    PubMed

    Zhu, Hong-Xiang; Cao, Xue-Juan; He, Yu-Cai; Kong, Qiao-Ping; He, Hui; Wang, Jin

    2015-09-20

    This study designed and synthesized a novel cellulose-based heavy metal adsorption material. One kind of bagasse pulp cellulose was pretreated under microwave 200 W for 3 min before the epoxidation, amination and ultrasonic enhancement sulfonation reaction. Heavy metal adsorption groups N and S were grafted onto the bagasse pulp cellulose. Furthermore, the effects of solution pH, adsorption temperature, adsorbent dosage, Cu(2+) concentration, and adsorbent recycling on adsorption capacity were investigated. Under the optimum condition, the adsorption amount of Cu(2+) was 35.2mg/g adsorbent. Compared with other cellulose-based adsorbents, this kind of adsorbent could be easily prepared and effectively recycled. Except for the normal fitting of adsorption process with the Langmuir isotherm adsorption model, Freundlich isotherm adsorption model and secondary adsorption kinetics model, the solid-liquid phase adsorption mechanism was also introduced to explain the Cu(2+) adsorption process. Three consecutive stages were deeply discussed and verified, where the surface diffusion and particle internal diffusion process were the primary along with a quick adsorption of the adsorbate onto the in-hole surface of the cellulose-based adsorbent.

  7. Methylene blue adsorption from aqueous solution by activated carbon: effect of acidic and alkaline solution treatments.

    PubMed

    Ijagbemi, Christianah O; Chun, Ji I; Han, Da H; Cho, Hye Y; O, Se J; Kim, Dong S

    2010-01-01

    The removal of Methylene Blue (MB) from aqueous solution using activated carbon (AC) has been investigated. Adsorption experiments were conducted and the maximum adsorption capacity was determined. The effect of experimental parameters such as pH, dye concentration and temperature were studied on the adsorption process. Equilibrium data were mathematically modeled using the Langmuir and Freundlich adsorption models to describe the equilibrium isotherms at different dye concentrations and temperature. Parameters of best-fit model were calculated and discussed. To understand the mechanism of adsorption, kinetic models were employed to follow the adsorption processes; the pseudo-first-order best described the adsorption of MB onto AC. It was found that pH plays a major role in the adsorption process; adsorption capacity was influenced by the physical and surface chemical properties of carbon and the pH of the solution. 99.0% MB removal was achieved at equilibrium.

  8. Amination of activated carbon for enhancing phenol adsorption: Effect of nitrogen-containing functional groups

    NASA Astrophysics Data System (ADS)

    Yang, Guo; Chen, Honglin; Qin, Hangdao; Feng, Yujun

    2014-02-01

    To study the contribution of different nitrogen-containing functional groups to enhancement of phenol adsorption, the aminated activated carbons (AC) were characterized by N2 adsorption/desorption, XPS, Boehm titration, and pH drift method and tested for adsorption behaviors of phenol. Adsorption isotherm fitting revealed that the Langmuir model was preferred for the aminated ACs. The adsorption capacity per unit surface area (qm/SSABET) was linearly correlated with the amount of pyridinic and pyrrolic N, which suggested that these two functional groups played a critical role in phenol adsorption. The enhancement of adsorption capacity was attributed to the strengthened π-π dispersion between phenol and basal plane of AC by pyridinic, pyrrolic N. The adsorption kinetics was found to follow the pseudo-second-order kinetic model, and intraparticle diffusion was one of the rate-controlling steps in the adsorption process.

  9. Adsorption thermodynamics of Methylene Blue onto bentonite.

    PubMed

    Hong, Song; Wen, Cheng; He, Jing; Gan, Fuxing; Ho, Yuh-Shan

    2009-08-15

    The effect of temperature on the equilibrium adsorption of Methylene Blue dye from aqueous solution using bentonite was investigated. The equilibrium adsorption data were analyzed using three widely applied isotherms: Langmuir, Freundlich, and Redlich-Peterson. A non-linear method was used for comparing the best fit of the isotherms. Best fit was found to be Redlich-Peterson isotherm. Thermodynamic parameters, such as DeltaG degrees, DeltaH degrees, and DeltaS degrees were calculated using adsorption equilibrium constant obtained from the Langmuir isotherm. Results suggested that the Methylene Blue adsorption on bentonite was a spontaneous and endothermic process.

  10. Density functional theory study of mercury adsorption on metal surfaces

    SciTech Connect

    Steckel, J.A.

    2008-01-01

    Density functional theory _DFT_ calculations are used to characterize the interaction of mercury with copper, nickel, palladium, platinum, silver, and gold surfaces. Mercury binds relatively strongly to all the metal surfaces studied, with binding energies up to _1 eV for Pt and Pd. DFT calculations underestimate the energy of adsorption with respect to available experimental data. Plane-wave DFT results using the local density approximation and the Perdew-Wang 1991 and Perdew-Burke-Ernzerhof parametrizations of the generalized gradient approximation indicate that binding of mercury at hollow sites is preferred over binding at top orbridge sites. The interaction with mercury in order of increasing reactivity over the six metals studied is Ag_Au_Cu_Ni_Pt_Pd. Binding is stronger on the _001_ faces of the metal surfaces, where mercury issituated in fourfold hollow sites as opposed to the threefold hollow sites on _111_ faces. In general, mercury adsorption leads to decreases in the work function; adsorbate-induced work function changes are particularly dramatic on Pt.

  11. Density functional theory study of mercury adsorption on metal surfaces

    SciTech Connect

    Steckel, Janice A.

    2008-03-10

    Density functional theory (DFT) calculations are used to characterize the interaction of mercury with copper, nickel, palladium, platinum, silver, and gold surfaces. Mercury binds relatively strongly to all the metal surfaces studied, with binding energies up to ~1eV for Pt and Pd. DFT calculations underestimate the energy of adsorption with respect to available experimental data. Plane-wave DFT results using the local density approximation and the Perdew-Wang 1991 and Perdew-Burke-Ernzerhof parametrizations of the generalized gradient approximation indicate that binding of mercury at hollow sites is preferred over binding at top or bridge sites. The interaction with mercury in order of increasing reactivity over the six metals studied is Agadsorption leads to decreases in the work function; adsorbate-induced work function changes are particularly dramatic on Pt.

  12. First principles study of NH3 adsorption on carbon nanowires

    NASA Astrophysics Data System (ADS)

    Tapia, Jorge-Alejandro; Sanchez, Alvaro-Daniel; Acosta, Cesar; Canto, Gabriel

    2009-03-01

    Recently has been reported a new type of one-dimensional carbon structures. Carbon nanowires formed by a linear carbon-atom chain inside an armchair (5,5) carbon nanotube has been observed using high-resolution transmission electron microscopy. Theoretical and experimental studies of the NH3 adsorption in the carbon nanotubes report changes in the electronic properties of the carbon nanotubes. In the present work we have studied the electronic and structure properties of carbon nanowires (chain@SWCNT) when NH3 atoms are adsorbed. We used the Density Functional Theory and the calculations where performed by the pseudopotentials LCAO method (SIESTA code) and the Generalized Gradient Approximation (GGA) for the exchange-correlation potential. We have analyzed the changes in the atomic structure and density of states (DOS). We found that the electronic character of the carbon chain of the chain@SWCNT system, can be modulate by NH3 adsorption. This research was supported by SEP under Grant No. PROMEP/103.5/07/2595 and the Consejo Nacional de Ciencia y Tecnolog'ia (Conacyt) under Grants No. 82497 and 60534.

  13. Adsorption Study on Moringa Oleifera Seeds and Musa Cavendish as Natural Water Purification Agents for Removal of Lead, Nickel and Cadmium from Drinking Water

    NASA Astrophysics Data System (ADS)

    Aziz, N. A. A.; Jayasuriya, N.; Fan, L.

    2016-07-01

    The effectiveness of plant based materials Moringa oleifera (Moringa) seeds and Musa cavendish (banana peel) for removing heavy metals namely lead (Pb), nickel (Ni) and cadmium (Cd) from contaminated groundwater was studied. Tests were carried out with individual and combined biomass at neutral pH condition on synthetic groundwater samples. The optimum biomass doses were determined as 200 mg/L for single biomass and 400 mg/L (in the ratio of 200 mg/L: 200 mg/L) for combined biomasses and used for adsorption isotherm studies with contact time of 30 minutes. Results showed that combined biomasses was able to met the Pb, Ni and Cd WHO standards from higher Pb, Ni and Cd initial concentrations which were up to 40 µg/L, 50 µg/L 9 µg/L, respectively compared to individual biomass of Moringa seed and banana peel. Moringa seeds exhibited the highest removal of Pb (81%) while the combined biomasses was most effective in removing Ni (74%) and Cd (97%) over wider their initial concentration ranges. The experimental data were linearized with Langmuir and Freundlich adsorption isotherm models. Freundlich model described the Pb adsorption better than the Langmuir model for all the tested biomasses. However, the Langmuir model fit better with the experimental data of Ni adsorption by Moringa seeds. Both models showed negligible differences in the coefficient of determination (R2) when applied for Ni and Cd adsorption on banana peel and combined biomasses, suggesting that there were multiple layers on the biomass interacting with the metals. Chemisorption is suggested to be involved in Pb adsorption for all tested biomasses as the value of nF calculated was lower than one. This type of adsorption could explain the phenomenon of different behavior of Pb removal and the higher Pb adsorption capacity (represented by KF values) compared to Ni and Cd. The study demonstrates that Moringa seeds, banana peel and their combination have the potential to be used as a natural alternative

  14. Removal of mercury(II) ions in aqueous solution using the peel biomass of Pachira aquatica Aubl: kinetics and adsorption equilibrium studies.

    PubMed

    Santana, Andrea J; dos Santos, Walter N L; Silva, Laiana O B; das Virgens, Cesário F

    2016-05-01

    Mercury is a highly toxic substance that is a health hazard to humans. This study aims to investigate powders obtained from the peel of the fruit of Pachira aquatica Aubl, in its in natura and/or acidified form, as an adsorbent for the removal of mercury ions in aqueous solution. The materials were characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis. The infrared spectra showed bands corresponding to the axial deformation of carbonyls from carboxylic acids, the most important functional group responsible for fixing the metal species to the adsorbent material. The thermograms displayed mass losses related to the decomposition of three major components, i.e., hemicellulose, cellulose, and lignin. The adsorption process was evaluated using cold-vapor atomic fluorescence spectrometry (CV AFS) and cold-vapor atomic absorption spectrometry (CV AAS). Three isotherm models were employed. The adsorption isotherm model, Langmuir-Freundlich, best represented the adsorption process, and the maximum adsorption capacity was predicted to be 0.71 and 0.58 mg g(-1) at 25 °C in nature and acidified, respectively. Adsorption efficiencies were further tested on real aqueous wastewater samples, and removal of Hg(II) was recorded as 69.6 % for biomass acidified and 76.3 % for biomass in nature. Results obtained from sorption experiments on real aqueous wastewater samples revealed that recovery of the target metal ions was very satisfactory. The pseudo-second-order model showed the best correlation to the experimental data. The current findings showed that the investigated materials are potential adsorbents for mercury(II) ion removal in aqueous solution, with acidified P. aquatica Aubl being the most efficient adsorbent.

  15. Removal of mercury(II) ions in aqueous solution using the peel biomass of Pachira aquatica Aubl: kinetics and adsorption equilibrium studies.

    PubMed

    Santana, Andrea J; dos Santos, Walter N L; Silva, Laiana O B; das Virgens, Cesário F

    2016-05-01

    Mercury is a highly toxic substance that is a health hazard to humans. This study aims to investigate powders obtained from the peel of the fruit of Pachira aquatica Aubl, in its in natura and/or acidified form, as an adsorbent for the removal of mercury ions in aqueous solution. The materials were characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis. The infrared spectra showed bands corresponding to the axial deformation of carbonyls from carboxylic acids, the most important functional group responsible for fixing the metal species to the adsorbent material. The thermograms displayed mass losses related to the decomposition of three major components, i.e., hemicellulose, cellulose, and lignin. The adsorption process was evaluated using cold-vapor atomic fluorescence spectrometry (CV AFS) and cold-vapor atomic absorption spectrometry (CV AAS). Three isotherm models were employed. The adsorption isotherm model, Langmuir-Freundlich, best represented the adsorption process, and the maximum adsorption capacity was predicted to be 0.71 and 0.58 mg g(-1) at 25 °C in nature and acidified, respectively. Adsorption efficiencies were further tested on real aqueous wastewater samples, and removal of Hg(II) was recorded as 69.6 % for biomass acidified and 76.3 % for biomass in nature. Results obtained from sorption experiments on real aqueous wastewater samples revealed that recovery of the target metal ions was very satisfactory. The pseudo-second-order model showed the best correlation to the experimental data. The current findings showed that the investigated materials are potential adsorbents for mercury(II) ion removal in aqueous solution, with acidified P. aquatica Aubl being the most efficient adsorbent. PMID:27084802

  16. Adsorption of diethyl phthalate ester to clay minerals.

    PubMed

    Wu, Yanhua; Si, Youbin; Zhou, Dongmei; Gao, Juan

    2015-01-01

    Phthalate esters are a group of plasticizers, which have been widely detected in China's agricultural and industrial soils. In this study, batch adsorption experiments were conducted to investigate the environmental effects on the adsorption of diethyl phthalate ester (DEP) to clay minerals. The results showed that DEP adsorption isotherms were well fitted with the Freundlich model; the interlayer spacing of K(+) saturated montmorillonite (K-mont) was the most important adsorption area for DEP, and di-n-butyl ester (DnBP) was limited to intercalate into the interlayer of K-mont due to the bigger molecular size; there was no significant effect of pH and ionic strength on DEP adsorption to K-mont/Ca-mont, but to Na-mont clay. The adsorption to kaolinite was very limited. Data of X-ray diffraction and FTIR spectra further proved that DEP molecules could intercalate into K-/Ca-mont interlayer, and might interact with clay through H-bonding between carbonyl groups and clay adsorbed water. Coated humic acid on clay surface would enhance DEP adsorption at low concentration, but not at high concentration (eg. Ce>0.26 mM). The calculated adsorption enthalpy (ΔHobs) and adsorption isotherms at varied temperatures showed that DEP could be adsorbed easier as more adsorbed. This study implied that clay type, compound structure, exchangeable cation, soil organic matter and temperature played important roles in phthalate ester's transport in soil.

  17. Comparative study of the adsorption of acetaminophen on activated carbons in simulated gastric fluid.

    PubMed

    Rey-Mafull, Carlos A; Tacoronte, Juan E; Garcia, Raquel; Tobella, Jorge; Llópiz, Julio C; Iglesias, Alberto; Hotza, Dachamir

    2014-01-01

    Samples of commercial activated carbons (AC) obtained from different sources: Norit E Supra USP, Norit B Test EUR, and ML (Baracoa, Cuba) were investigated. The adsorption of acetaminophen, Co = 2500 mg/L, occured in simulated gastric fluid (SGF) at pH 1.2 in contact with activated carbon for 4 h at 310 K in water bath with stirring. Residual acetaminophen was monitored by UV visible. The results were converted to scale adsorption isotherms using alternative models: Langmuir TI and TII, Freundlich, Dubinin-Radushkevich (DR) and Temkin. Linearized forms of the characteristic parameters were obtained in each case. The models that best fit the experimental data were Langmuir TI and Temkin with R(2) ≥0.98. The regression best fits followed the sequence: Langmuir TI = Temkin > DR > LangmuirTII > Freundlich. The microporosity determined by adsorption of CO2 at 273 K with a single term DR regression presented R(2) > 0.98. The adsorption of acetaminophen may occur in specific sites and also in the basal region. It was determined that the adsorption process of acetaminophen on AC in SGF is spontaneous (ΔG <0) and exothermic (-ΔHads.). Moreover, the area occupied by the acetaminophen molecule was calculated with a relative error from 7.8 to 50%.

  18. Comparative study of the adsorption of acetaminophen on activated carbons in simulated gastric fluid.

    PubMed

    Rey-Mafull, Carlos A; Tacoronte, Juan E; Garcia, Raquel; Tobella, Jorge; Llópiz, Julio C; Iglesias, Alberto; Hotza, Dachamir

    2014-01-01

    Samples of commercial activated carbons (AC) obtained from different sources: Norit E Supra USP, Norit B Test EUR, and ML (Baracoa, Cuba) were investigated. The adsorption of acetaminophen, Co = 2500 mg/L, occured in simulated gastric fluid (SGF) at pH 1.2 in contact with activated carbon for 4 h at 310 K in water bath with stirring. Residual acetaminophen was monitored by UV visible. The results were converted to scale adsorption isotherms using alternative models: Langmuir TI and TII, Freundlich, Dubinin-Radushkevich (DR) and Temkin. Linearized forms of the characteristic parameters were obtained in each case. The models that best fit the experimental data were Langmuir TI and Temkin with R(2) ≥0.98. The regression best fits followed the sequence: Langmuir TI = Temkin > DR > LangmuirTII > Freundlich. The microporosity determined by adsorption of CO2 at 273 K with a single term DR regression presented R(2) > 0.98. The adsorption of acetaminophen may occur in specific sites and also in the basal region. It was determined that the adsorption process of acetaminophen on AC in SGF is spontaneous (ΔG <0) and exothermic (-ΔHads.). Moreover, the area occupied by the acetaminophen molecule was calculated with a relative error from 7.8 to 50%. PMID:24570846

  19. Interactions between sparfloxacin and antacids - dissolution and adsorption studies.

    PubMed

    Hussain, Fida; Arayne, M Saeed; Sultana, Najma

    2006-01-01

    Sparfloxacin is a broad-spectrum oral fluoroquinolone antimicrobial agent with a long elimination half-life, extensively used against both Gram-positive as well as Gram-negative microorganism. Concurrent administration of antacids and sparfloxacin decreases the gastrointestinal absorption of sparfloxacin and therapeutic failure may result. The present study was designed to evaluate the influence of some antacids on the availability of sparfloxacin. The release of sparfloxacin from tablets in the presence of antacids like sodium bicarbonate, calcium hydroxide, calcium carbonate, aluminum hydroxide, magnesium hydroxide, magnesium carbonate, magnesium trisilicate and magaldrate has been studied on BP 2003 dissolution test apparatus. These studies were carried out in simulated gastric and intestinal juices for three hours at 37 degrees C. The results confirmed that the dissolution rate of tablets was markedly retarded in the presence all of antacids studied, whereas magaldrate and calcium carbonate exhibited relatively higher adsorption capacities in simulated gastric juice and magnesium trisilicate and calcium hydroxide in simulated intestinal juice.

  20. Interactions between ciprofloxacin and antacids--dissolution and adsorption studies.

    PubMed

    Arayne, M Saeed; Sultana, Najma; Hussain, Fida

    2005-01-01

    Ciprofloxacin is a fluorinated quinolone antibacterial agent extensively used against both Gram-positive and Gram-negative microorganisms. In certain polytherapy programs, ciprofloxacin can be administered with some antacids that could modify its dissolution rate and reduce its absorption leading to therapeutic failure. The aim of this study was to evaluate the influence of some antacids on the availability of ciprofloxacin. The release of ciprofloxacin from tablets in the presence of antacids, such as sodium bicarbonate, calcium hydroxide, calcium carbonate, aluminum hydroxide, magnesium hydroxide, magnesium carbonate, magnesium trisilicate and magaldrate was studied on BP 2002 dissolution test apparatus. These studies were carried out in simulated gastric and intestinal juices for 3 hours at 37 degrees C. The results confirmed that the dissolution rate of tablets was markedly retarded in the presence of all the antacids studied. Magaldrate and calcium carbonate in simulated gastric juice exhibited relatively higher adsorption capacities, as did magnesium trisilicate and calcium hydroxide in simulated intestinal juice.

  1. A theoretical study of CO adsorption on FeCo(100) and the effect of alloying

    NASA Astrophysics Data System (ADS)

    Rochana, Panithita; Wilcox, Jennifer

    2011-04-01

    FeCo catalysts are modeled for optimizing the Fischer-Tropsch synthesis process since they can be tuned to enhance CO activity and resist poisoning. The electronic properties associated with CO adsorption are studied using plane-wave density functional theory (DFT). The range of computed adsorption energies from this work falls between the CO adsorption energies on pure Fe and Co surfaces. It was found that CO prefers to adsorb on the top site of the Co surface of FeCo alloys, whereas CO has stronger adsorption on pure Fe rather than pure Co surface. The trend in adsorption energy is top-Co > hollow-Fe > top-Fe > hollow-Co > bridge-Co > bridge-Fe. This change in preferable metal for adsorption ( i.e., from Fe in a pure system to Co in the FeCo alloy surface in the current investigation) is due to the shift in the d-band center of the alloyed material. It implies that alloying Fe with Co changes the properties of the pure metal and ultimately affects the CO adsorption energy; however, the mechanism of adsorption remains similar and can be explained using the Nilsson-Pettersson model. Additional CO configurations consisting of hollow-site adsorption with a tilted geometry, was also investigated. The corresponding adsorption energy was found to be slightly higher than the adsorption energy when CO is adsorbed on the top-Co site.

  2. [Adsorption of Cr (VI) on magnetic graphene from aqueous solution].

    PubMed

    Liu, Wei; Yang, Qi; Li, Bo; Chen, Hai; Nie, Lan-Yu

    2015-02-01

    Chemical deposition method was applied to prepare magnetic graphene composites using graphite oxide and ferric salt (FeCl2 - 4H2O and FeCl3 x 6H2O) as starting materials. The static experiments were performed to study kinetics, thermodynamic, adsorption isotherm and effects of various parameters, such as pH, temperature and time on Cr(VI) adsorption. The results showed that adsorption kinetics followed the pseudo-second-order model. Compared with Freundlich isotherm, Langmuir isotherm could better describe the adsorption process. The parameters of thermodynamics were ΔHθ = 33.89 kJ x mol(-1), ΔSθ = 120.15 J x (mol x K)(-1), ΔGθ = -2.51 kJ x mol(-1) (303 K), it demonstrated that the adsorption was a spontaneously endothermic process. It also indicated that the optimal pH was 2. Higher temperature and extension of time were in favor of adsorption. When used repeatedly for three times, the adsorption capacity decreased from 3.9 mg x g(-1) to 2.1 mg x g(-1) with an initial concentration of 5 mg x L(-1). By using a permanent magnet, the recycling process of adsorbent was easy to be operated and adsorbent could be regenerated by sodium hydrate solution. Hence, the composites is a promising adsorbent for efficient removal of Cr(VI) from wastewater. PMID:26031080

  3. Iodine adsorption on Ni(111): STM and DFT study

    NASA Astrophysics Data System (ADS)

    Komarov, N. S.; Pavlova, T. V.; Andryushechkin, B. V.

    2016-09-01

    Iodine adsorption on the Ni(111) surface has been studied in ultra-high vacuum conditions with scanning tunneling microscopy (STM), Auger electron spectroscopy (AES), low-energy electron diffraction (LEED) and density functional theory (DFT) calculations. At the first stage of adsorption, iodine was found to form a simple commensurate (√{ 3 } ×√{ 3 }) R 30∘ structure at the coverage of 0.33 ML. According to DFT calculations, all iodine atoms in the (√{ 3 } ×√{ 3 }) R 30∘ structure occupy fcc hollow sites. Increase of the coverage in the range of (0.333 ML <θ < 0.364 ML) results in the uniaxial compression of the iodine lattice and the formation of the high-order commensurate structure (11 ×√{ 3 } R 30∘). The mechanism of compression involves the formation and the development of the striped super-heavy domain wall network. Further iodine dosing gives rise to nucleation and growth of flat 2D islands of surface nickel iodide. Atomic resolution STM images of iodide islands, in addition to atomic modulation, exhibit clear visible moiré-like superstructures with a period about 26 Å. The origin of the moiré-patterns was explained by the incommensurability of lattices of the surface nickel iodide and underlying Ni(111).

  4. Adsorption and desorption studies of cesium on sapphire surfaces

    SciTech Connect

    Zavadil, K.R.; Ing, J.L.

    1993-12-01

    Adsorption/desorption were studied using combined surface analytical techniques. An approximate initial sticking coefficient for Cs on sapphire was measured using reflection mass spectrometry and found to be 0.9. Thermal Desorption Mass Spectrometry (TDMS) and Auger Electron Spectroscopy (AES) were used to verify that a significant decrease in sticking coefficient occurs as the Cs coverage reaches a critical submonolayer value. TDMS analysis demonstrates that Cs is stabilized on a clean sapphire surface at temperatures (1200 K) in excess of the temperatures experienced by sapphire in a TOPAZ-2 thermionic fuel element (TFE). Surface contaminants on sapphire can enhance Cs adsorption relative to the clean surface. C contamination eliminates the high temperature state of Cs desorption found on clean sapphire but shifts the bulk of the C desorption from 400 to 620 K. Surface C is a difficult contaminant to remove from sapphire, requiring annealing above 1400 K. Whether Cs is stabilized on sapphire in a TFE environment will most likely depend on relation between surface contamination and surface structure.

  5. Ethane adsorption on aggregates of dahlia-like nanohorns: experiments and computer simulations.

    PubMed

    Russell, Brice A; Migone, Aldo D; Petucci, Justin; Mercedes Calbi, M; Yudasaka, Masako; Iijima, Sumio

    2016-06-01

    This is a report on a study of the adsorption characteristics of ethane on aggregates of unopened dahlia-like carbon nanohorns. This sorbent presents two main groups of adsorption sites: the outside surface of individual nanohorns and deep, interstitial spaces between neighbouring nanohorns towards the interior of the aggregates. We have explored the equilibrium properties of the adsorbed ethane films by determining the adsorption isotherms and isosteric heat of adsorption. Computer simulations performed on different model structures indicate that the majority of ethane adsorption occurs on the outer region of the aggregates, near the ends of the nanohorns. We have also measured the kinetics of adsorption of ethane on this sorbent. The measurements and simulations were conducted along several isotherms spanning the range between 120 K and 220 K. PMID:27218414

  6. Determination of Equilibrium and Kinetic Parameters of the Adsorption of Cr(III) and Cr(VI) from Aqueous Solutions to Agave Lechuguilla Biomass

    PubMed Central

    Romero-González, Jaime; Peralta-Videa, José R.; Rodríguez, Elena

    2005-01-01

    This investigation reveals the capability of Agave lechuguilla for trivalent and hexavalent chromium removal from aqueous solutions. Experimentation included pH profile, time dependence, adsorption capacity (KF and QL), adsorption intensity (n and RL) and saturation capacity (q s) studies. Batch experiments were conducted at 22∘C to characterize and model the adsorption equilibrium as well as biomass adsorption rates. pH 4 was the optimum for Cr(III) binding, while Cr(VI) optimum binding was at pH 2. Time profile experiments indicated that the adsorption of Cr(VI) by lechuguilla biomass was time-dependent and that of Cr(III) was not. Kinetic models demonstrated that a pseudo-second order reaction model best described the kinetic data for Cr(VI). The adsorption isotherms showed that the binding pattern for Cr(VI) followed the Freundlich isotherm model, while that for Cr(III) followed the Langmuir isotherm. PMID:18365089

  7. Sulfate adsorption on goethite

    SciTech Connect

    Rietra, R.P.J.J.; Hiemstra, T.; Riemsdijk, W.H. van

    1999-10-15

    Recent spectroscopic work has suggested that only one surface species of sulfate is dominant on hematite. Sulfate is therefore a very suitable anion to test and develop adsorption models for variable charge minerals. The authors have studied sulfate adsorption on goethite covering a large range of sulfate concentrations, surface coverages, pH values, and electrolyte concentrations. Four different techniques were used to cover the entire range of conditions. For characterization at low sulfate concentrations, below the detection limit of sulfate with ICP-AES, the authors used proton-sulfate titrations at constant pH. Adsorption isotherms were studied for the intermediate sulfate concentration range. Acid-base titrations in sodium sulfate and electromobility were used for high sulfate concentrations. All the data can be modeled with one adsorbed species if it is assumed that the charge of adsorbed sulfate is spatially distributed in the interface. The charge distribution of sulfate follows directly from modeling the proton-sulfate adsorption stoichoimemtry sine this stoichiometry is independent of the intrinsic affinity constant of sulfate. The charge distribution can be related to the structure of the surface complex by use of the Pauling bond valence concept and is in accordance with the microscopic structure found by spectroscopy. The intrinsic affinity constant follows from the other measurements. Modeling of the proton-ion stoichoimetry with the commonly used 2-pK models, where adsorbed ions are treated as point charges, is possible only if at least two surface species for sulfate are used.

  8. Adsorption of halogenated aliphatic contaminants by graphene nanomaterials.

    PubMed

    Zhou, Yang; Apul, Onur Guven; Karanfil, Tanju

    2015-08-01

    In this study, adsorption of ten environmentally halogenated aliphatic synthetic organic compounds (SOCs) by a pristine graphene nanosheet (GNS) and a reduced graphene oxide (rGO) was examined, and their adsorption behaviors were compared with those of a single-walled carbon nanotube (SWCNT) and a granular activated carbon (GAC). In addition, the impacts of background water components (i.e., natural organic matter (NOM), ionic strength (IS) and pH) on the SOC adsorption behavior were investigated. The results indicated HD3000 and SWCNT with higher microporous volumes exhibited higher adsorption capacities for the selected aliphatic SOCs than graphenes, demonstrating microporosity of carbonaceous adsorbents played an important role in the adsorption. Analysis of adsorption isotherms demonstrated that hydrophobic interactions were the dominant contributor to the adsorption of aliphatic SOCs by graphenes. However, π-π electron donor-acceptor and van der Waals interactions are likely the additional mechanisms contributing to the adsorption of aliphatic SOCs on graphenes. Among the three background solution components examined, NOM showed the most influential effect on adsorption of the selected aliphatic SOCs, while pH and ionic strength had a negligible effects. The NOM competition on aliphatic adsorption was less pronounced on graphenes than SWCNT. Overall, in terms of adsorption capacities, graphenes tested in this study did not exhibit a major advantage over SWCNT and GAC for the adsorption of aliphatic SOCs.

  9. Adsorption of cadmium from aqueous solutions by perlite.

    PubMed

    Mathialagan, T; Viraraghavan, T

    2002-10-14

    The present study examined the use of perlite for the removal of cadmium from aqueous solutions. The effects of pH and contact time on the adsorption process were examined. The optimum pH for adsorption was found to be 6.0. Residual cadmium concentration reached equilibrium in 6h and the rate of cadmium adsorption by perlite was rapid in the first hour of the reaction time. Ho's pseudo-second-order model best described the kinetics of the reaction. Batch adsorption experiments conducted at room temperature (22+/-1 degrees C) showed that the adsorption pattern followed the Freundlich isotherm model. The maximum removal of cadmium obtained from batch studies was 55%. Thomas model was used to describe the adsorption data from column studies. The results generally showed that perlite could be considered as a potential adsorbent for cadmium removal from aqueous solutions.

  10. Kinetic studies of sulfide mineral oxidation and xanthate adsorption

    NASA Astrophysics Data System (ADS)

    Mendiratta, Neeraj K.

    2000-10-01

    studies have been used to elucidate the depressing action of DETA and SO2. It was observed that DETA and SO2 complement each other in maintaining lower pulp potentials and removing polysulfides. DETA also helps in deactivating pyrrhotite. Therefore, the combined use of DETA and SO2 leads to the inhibition of both the collectorless flotation and the adsorption of xanthate. The adsorption of xanthate on sulfide minerals is a mixed-potential mechanism, i.e., the anodic oxidation of xanthate requires a cathodic counterpart. Normally, the cathodic reaction is provided by the reduction of oxygen. However, oxygen can be replaced by other oxidants. Ferric ions are normally present in the flotation pulp. Their source could be either iron from the grinding circuit or the ore itself. The galvanic studies were carried out to test the possibility of using ferric ions as oxidants and positive results were obtained. Tafel studies were carried out to measure the activation energies for the adsorption of ethylxanthate on several sulfide minerals. Pyrite, pyrrhotite (pure and nickel activated), chalcocite and covellite were studied in 10 -4 M ethylxanthate solution at pH 6.8 at temperatures in the range of 22--30°C. The Tafel studies showed that xanthate adsorbs as dixanthogen (X2) on pyrite and pyrrhotite, nickel dixanthate (NiX2) on nickel-activated pyrrhotite and cuprous xanthate (CuX) on both chalcocite and covellite. However, the mechanism for xanthate adsorption on each mineral is different. The free energy of reaction estimated from the activation energies are in good agreement with thermodynamically calculated ones.

  11. A comparative study for adsorption of lysozyme from aqueous samples onto Fe3O4 magnetic nanoparticles using different ionic liquids as modifier.

    PubMed

    Kamran, Sedigheh; Absalan, Ghodratollah; Asadi, Mozaffar

    2015-12-01

    In this paper, nanoparticles of Fe3O4 as well as their modified forms with different ionic liquids (IL-Fe3O4) were prepared and used for adsorption of lysozyme. The mean size and the surface morphology of the nanoparticles were characterized by TEM, XRD and FTIR techniques. Adsorption studies of lysozyme were performed under different experimental conditions in batch system on different modified magnetic nanoparticles such as, lysozyme concentration, pH of the solution, and contact time. Experimental results were obtained under the optimum operational conditions of pH 9.0 and a contact time of 10 min when initial protein concentrations of 0.05-2.0 mg mL(-1) were used. The isotherm evaluations revealed that the Langmuir model attained better fits to the equilibrium data than the Freundlich model. The maximum obtained adsorption capacities were 370.4, 400.0 500.0 and 526.3 mg of lysozyme for adsorption onto Fe3O4 and modified magnetic nanoparticles by [C4MIM][Br], [C6MIM][Br] and [C8MIM][Br] per gram of adsorbent, respectively. The Langmuir adsorption constants were 0.004, 0.019, 0.024 and 0.012 L mg(-1) for adsorptions of lysozyme onto Fe3O4 and modified magnetic nanoparticles by [C4MIM][Br], [C6MIM][Br] and [C8MIM][Br], respectively. The adsorption capacity of lysozyme was found to be dependent on its chemical structure, pH of the solution, temperature and type of ionic liquid as modifier. The applicability of two kinetic models including pseudo-first order and pseudo-second order model was estimated. Furthermore, the thermodynamic parameters were calculated. Protein could desorb from IL-Fe3O4 nanoparticles by using NaCl solution at pH 9.5 and was reused.

  12. DSC study of the isothermal crystallization of iPP-CNF nanocomposites

    NASA Astrophysics Data System (ADS)

    Chipara, Dorina M.; Chipara, Mircea

    2013-03-01

    Nanocomposite materials have been obtained by dispersing vapor grown carbon nanofibers (VGCNFs) with diameters ranging between 60 and 100 nm and lengths between 30,000 and 100,000 nm supplied by Pyrograf Products, Inc (PR-24AG) within a polymer matrix - isotactic polypropylene (iPP) - type Marlex HLN-120-01 with density 0.906 g/cm3 and melt flow rate at 230 oC of 12 g/10 min, supplied by Philips Sumika Polypropylene Company. VGCNFs have been purified and disentangled by reflux in dichloromethane and deionized water followed by vacuum filtering (for 24 h) and drying at 110 oC for 24h. The nanocomposites were obtained by melt mixing at 180 oC for 9 minutes with a speed of 65 rpm followed by an additional mixing at 90 rpm for 5 minutes, using a HAAKE Rheomix, Nanocomposites loaded with various amounts of VGCNFs (0%, 1%, 2.5%, 5%, 7.5%, 10%, 15%, and 20% wt.) have been prepared and investigated by TA DSC Q-500. Isothermal crystallization was investigated in detail and analyzed by using an expression derived from the Avrami equation. The effect of the filler on the isothermal crystallization of iPP is discussed in detail. The research is focused on the effect of VGCNF on the degree of crystallization of iPP, crystallization rate, and dimensionality of the crystallization process. This research has been supported by National Science Foundation under DMR. Contract grant number 0934157.

  13. Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite.

    PubMed

    Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

    2015-01-01

    Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g · L(-1), in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics. PMID:26698573

  14. Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite

    PubMed Central

    Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

    2015-01-01

    Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g·L-1, in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics. PMID:26698573

  15. Studies on Adsorption and Corrosion Inhibitive Properties of Indoline Compounds on N80 Steel in Hydrochloric Acid

    NASA Astrophysics Data System (ADS)

    Yadav, M.; Sarkar, T. K.; Purkait, Taniya

    2015-12-01

    Corrosion inhibition performance of synthesized indoline compounds, namely, 3'-(4-(1-acetyl-5-(4-methoxyphenyl)-4,5-dihydro-1H-pyrazol-3-yl)phenyl)spiro[indoline-3,2'-thiazolidine]-2,4'-dione (MPIT ) and 1-(4-(1-acetyl-5-(4-methoxyphenyl)-4,5-dihydro-1H-pyrazol-3-yl)phenyl)spiro[imidazolidine-2,3'-indoline]-2',5-dione (MPII) on N80 steel in 15% HCl solution was studied using weight loss measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Polarization studies showed that both studied inhibitors were of mixed type in nature. The adsorption of inhibitors on the N80 steel surface obeys Langmuir adsorption isotherm. The potential of zero charge ( E PZC) for the N80 steel was determined by EIS method. Scanning electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy were used to characterize the surface morphology of uninhibited and inhibited N80 steel specimens. The density functional theory was employed for theoretical calculations.

  16. Measurements of water vapor adsorption on The Geysers rocks

    SciTech Connect

    Gruszkiewicz, M.S.; Horita, J.; Simonson, J.M.; Mesmer, R.E.

    1996-04-01

    One of the goals of this project is to determine the dependence of the water retention capacity of the rocks as a function of temperature. The results show a significant dependence of the adsorption and desorption isotherms on the grain size of the sample. The increase in the amount of water retained with temperature observed previously between 90 and 30{degrees}C for various reservoir rocks from The Geysers may be due to the contribution of slow chemical adsorption and may be dependent on the time allowed for equilibration. In contrast with the results of Shang, some closed and nearly closed hysteresis loops on the water adsorption/desorption isotherms were obtained in this study. In these cases the effects of activated processes were not present, and no increase in water adsorption with temperature was observed.

  17. A study of metal ion adsorption at low suspended-solid concentrations

    USGS Publications Warehouse

    Chang, Cecily C.Y.; Davis, J.A.; Kuwabara, J.S.

    1987-01-01

    A procedure for conducting adsorption studies at low suspended solid concentrations in natural waters (<50 mg l-1) is described. Methodological complications previously associated with such experiments have been overcome. Adsorption of zinc ion onto synthetic colloidal titania (TiO2) was studied as a function of pH, supporting electrolyte (NaCl) concentration (0??1-0??002 m) and particle concentration (2-50 mg l-1). The lack of success of the Davis Leckie site bonding model in describing Zn(II) adsorption emphasizes the need for further studies of adsorption at low suspended-solid concentrations. ?? 1987.

  18. Biosorptive uptake of Fe(2+), Cu(2+) and As(5+) by activated biochar derived from Colocasia esculenta: Isotherm, kinetics, thermodynamics, and cost estimation.

    PubMed

    Banerjee, Soumya; Mukherjee, Shraboni; LaminKa-Ot, Augustine; Joshi, S R; Mandal, Tamal; Halder, Gopinath

    2016-09-01

    The adsorptive capability of superheated steam activated biochar (SSAB) produced from Colocasia esculenta was investigated for removal of Cu(2+), Fe(2+) and As(5+) from simulated coal mine wastewater. SSAB was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy and Brunauer-Emmett-Teller analyser. Adsorption isotherm indicated monolayer adsorption which fitted best in Langmuir isotherm model. Thermodynamic study suggested the removal process to be exothermic, feasible and spontaneous in nature. Adsorption of Fe(2+), Cu(2+) and As(5+) on to SSAB was found to be governed by pseudo-second order kinetic model. Efficacy of SSAB in terms of metal desorption, regeneration and reusability for multiple cycles was studied. Regeneration of metal desorbed SSAB with 1 N sodium hydroxide maintained its effectiveness towards multiple metal adsorption cycles. Cost estimation of SSAB production substantiated its cost effectiveness as compared to commercially available activated carbon. Hence, SSAB could be a promising adsorbent for metal ions removal from aqueous solution.

  19. High-temperature adsorption of n-octane, benzene, and chloroform onto silica gel surface

    SciTech Connect

    Bilinski, B.

    2000-05-01

    The adsorption properties of silica gel surface for compounds differing in types of intermolecular interactions were studied under conditions in which the same silica was investigated by means of a gas phase titration method, i.e., at high temperature and low surface coverage. Adsorption isotherms of n-octane, benzene, and chloroform were determined at 373, 363, and 353 K. Based on these isotherms the isosteric heat of adsorption was calculated. Moreover, the adsorption energy distribution function and the derivative of film pressure with respect to the adsorbed amount were computed from the isotherms determined at 373 K. The obtained results were compared to those determined by gas phase titration. It was stated that on the dependencies of film pressure derivative some linear sections appeared that corresponded to the inflection points on gas phase titration curves. The results are discussed in terms of both the type and the strength of surface-molecule interactions.

  20. [Adsorption and Desorption Characteristics of Endosulfan in Purple Soil].

    PubMed

    Zhao, Yan; Zheng, Guo-can; Zhu, Heng; Zhang, Jin-zhong; Zhu, Xiu-ying; Hu, Shu-chun; Wu, Ya-lin

    2015-09-01

    In order to reveal the residual process of endosulfan in purple soil and protect soil ecological environment, the adsorption and desorption characteristics of endosulfan in purple soil were investigated, and effects of temperature, adsorbent amount, and initial pH of adsorption solution on the adsorption capacity were also examined by static adsorption and desorption experiments. The results showed that the adsorption kinetic process could be well described by the second-order kinetic equation with the initial rate constants of α-, β-endosulfan as 0. 157 and 0. 115 mg.(g.min)-1, respectively. The adsorption thermodynamic process could be well described by the Langmuir isotherm with the maximum adsorption capacities of α-, β-endosulfan as 0. 257 mg . g -1 and 0. 155 mg . g -1, respectively. The adsorption process of endosulfan in purple soil may be an exothermic physicochemical process, and is dominated by physical adsorption. Under the experimental conditions examined in this study, the initial pH of adsorption solution had a relative great influence on the adsorption capacity, whereas the temperature and adsorbent amount had no significant influence. The desorption experiments found that the maximum desorption capacities of α-, β-endosulfan adsorbed in purple soil were 0. 029 mg . g -1 and 0. 017 mg . g -1 at 6 and 4 h, and accounted for 10. 5% and 16. 1% in the maximum adsorption capacities, respectively. PMID:26717711

  1. [Adsorption and Desorption Characteristics of Endosulfan in Purple Soil].

    PubMed

    Zhao, Yan; Zheng, Guo-can; Zhu, Heng; Zhang, Jin-zhong; Zhu, Xiu-ying; Hu, Shu-chun; Wu, Ya-lin

    2015-09-01

    In order to reveal the residual process of endosulfan in purple soil and protect soil ecological environment, the adsorption and desorption characteristics of endosulfan in purple soil were investigated, and effects of temperature, adsorbent amount, and initial pH of adsorption solution on the adsorption capacity were also examined by static adsorption and desorption experiments. The results showed that the adsorption kinetic process could be well described by the second-order kinetic equation with the initial rate constants of α-, β-endosulfan as 0. 157 and 0. 115 mg.(g.min)-1, respectively. The adsorption thermodynamic process could be well described by the Langmuir isotherm with the maximum adsorption capacities of α-, β-endosulfan as 0. 257 mg . g -1 and 0. 155 mg . g -1, respectively. The adsorption process of endosulfan in purple soil may be an exothermic physicochemical process, and is dominated by physical adsorption. Under the experimental conditions examined in this study, the initial pH of adsorption solution had a relative great influence on the adsorption capacity, whereas the temperature and adsorbent amount had no significant influence. The desorption experiments found that the maximum desorption capacities of α-, β-endosulfan adsorbed in purple soil were 0. 029 mg . g -1 and 0. 017 mg . g -1 at 6 and 4 h, and accounted for 10. 5% and 16. 1% in the maximum adsorption capacities, respectively.

  2. Adsorption of thorium(IV) from simulated radioactive solutions using a novel electrospun PVA/TiO2/ZnO nanofiber adsorbent functionalized with mercapto groups: Study in single and multi-component systems

    NASA Astrophysics Data System (ADS)

    Alipour, Dariush; Keshtkar, Ali Reza; Moosavian, Mohammad Ali

    2016-03-01

    The novel polyvinyl alcohol/titanium oxide/zinc oxide (PVA/TiO2/ZnO) nanofiber adsorbent functionalized with 3-mercaptopropyltrimethoxysilane (TMPTMS) was prepared by electrospinning method and its potential was investigated for the adsorption of thorium from single and multi-metal aqueous solutions. The prepared adsorbent was characterized by FTIR, SEM and BET analysis. The influences of different operational parameters such as pH, ionic strength, equilibrium time, initial concentration and temperature were studied in batch mode. Investigation of ionic strength effect showed that the addition of NaNO3 to metal solution has a slight effect on the thorium adsorption, whereas pH value has a serious effect on the thorium adsorption at pH values lower than 4. The double-exponential model described the adsorption of Th(IV) ions much better than other kinetic models within both the single and multi-component systems. Among various isotherm models used, the equilibrium data of Th(IV) conformed the Langmuir isotherm in the single system, while those were best fitted by Dubinin-Radushkevich (D-R) isotherm in multi-component system. Thermodynamic parameters such as ΔH°, ΔS°, and ΔG° indicated that the nature of adsorption process was spontaneous, endothermic and thermodynamically favored. The inhibitory effect of other metal ions on the adsorption capacity of Th(IV) was in order of Al(III) > Cu(II) > Cd(II) > Ni(II) > U(VI) > Fe(II).

  3. A computational study of electrolyte adsorption in a simple model for intercalated clays

    NASA Astrophysics Data System (ADS)

    Lomba, E.; Weis, J.-J.

    2010-03-01

    A pillared interlayered clay is represented by a two-dimensional quenched charged disordered medium, in which the pillar configuration is produced by the quench of a two-dimensional electrolyte and the subsequent removal of the anions (that act as a template). The cation charge is counterbalanced by a neutralizing background that is an ideal representation of the layer's negative charge in the experimental system. In this paper we investigate the adsorption of electrolyte particles in this charged disordered medium resorting both to the use of the replica Ornstein-Zernike equation in the hypernetted chain approximation and grand canonical Monte Carlo simulations. The theoretical approach qualitatively reproduces the simulated behavior of the adsorbed fluids. Theoretical estimates of the material porosities obtained for various types of pillar distributions are in good agreement with the simulation. We investigate the influence of the matrix on correlation functions and adsorption isotherms.

  4. Adsorption kinetics of herbicide paraquat from aqueous solution onto activated bleaching earth.

    PubMed

    Tsai, W T; Lai, C W; Hsien, K J

    2004-05-01

    In the present study, the activated bleaching earth was used as adsorbent for the herbicide paraquat adsorption in a batch adsorber. The rate of adsorption has been investigated under the controlled process parameters like agitation speed, initial paraquat concentration, adsorbent dosage and temperature. A batch kinetic model, based on the assumption of a pseudo-second order mechanism, has been tested to predict the rate constant of adsorption, equilibrium adsorption capacity, time of half-adsorption, and equilibrium concentration by the fittings of the experimental data. The results of the kinetic studies show that the adsorption process can be well described with the pseudo-second order equation. Based on the isotherm data obtained from the fittings of the adsorption kinetics, Freundlich model appears to fit the adsorption better than Langmuir model. In addition, the effective diffusion coefficient has also been estimated based on the restrictive diffusion model.

  5. Adsorption behaviors of some phenolic compounds onto high specific area activated carbon cloth.

    PubMed

    Ayranci, Erol; Duman, Osman

    2005-09-30

    Adsorption of phenol, hydroquinone, m-cresol, p-cresol and p-nitrophenol from aqueous solutions onto high specific area activated carbon cloth has been studied. The effect of ionization on adsorption of these ionizable phenolic compounds was examined by studying the adsorption from acidic, basic and natural pH solutions. Kinetics of adsorption was followed by in situ UV spectroscopy over a period of 90 min. First-order rate law was found to be valid for the kinetics of adsorption processes and the rate constants were determined. The highest rate constants were obtained for the adsorption from solutions at the natural pH. The lowest rate constants were observed in basic solutions. The rate constants decreased in the order p-nitrophenol approximately m-cresol>p-cresol>hydroquinone approximately phenol. Adsorption isotherms were derived at 30 degrees C and the isotherm data were treated according to Langmuir, Freundlich and Tempkin isotherm equations. The goodness of fit of experimental data to these isotherm equations was tested and the parameters of equations were determined. The possible interactions of compounds with the carbon surface were discussed considering the charge of the surface and the possible ionization of compounds at acidic, basic and natural pH conditions. PMID:15941619

  6. Crystallization characteristics in supercooled liquid zinc during isothermal relaxation: A molecular dynamics simulation study

    PubMed Central

    Zhou, Li-li; Liu, Rang-su; Tian, Ze-an; Liu, Hai-rong; Hou, Zhao-yang; Peng, Ping

    2016-01-01

    The crystallization characteristics in supercooled liquid Zn during isothermal relaxation were investigated using molecular dynamics simulations by adopting the cluster-type index method (CTIM) and the tracing method. Results showed that the crystallization process undergo three different stages. The size of the critical nucleus was found to be approximately 90–150 atoms in this system; the growth of nuclei proceeded via the successive formation of hcp and fcc structures with a layered distribution; and finally, the system evolved into a much larger crystal with a distinct layered distribution of hcp and fcc structures with an 8R stacking sequence of ABCBACAB by adjusting all of the atoms in the larger clusters according to a certain rule. PMID:27526660

  7. Crystallization characteristics in supercooled liquid zinc during isothermal relaxation: A molecular dynamics simulation study.

    PubMed

    Zhou, Li-Li; Liu, Rang-Su; Tian, Ze-An; Liu, Hai-Rong; Hou, Zhao-Yang; Peng, Ping

    2016-01-01

    The crystallization characteristics in supercooled liquid Zn during isothermal relaxation were investigated using molecular dynamics simulations by adopting the cluster-type index method (CTIM) and the tracing method. Results showed that the crystallization process undergo three different stages. The size of the critical nucleus was found to be approximately 90-150 atoms in this system; the growth of nuclei proceeded via the successive formation of hcp and fcc structures with a layered distribution; and finally, the system evolved into a much larger crystal with a distinct layered distribution of hcp and fcc structures with an 8R stacking sequence of ABCBACAB by adjusting all of the atoms in the larger clusters according to a certain rule. PMID:27526660

  8. Crystallization characteristics in supercooled liquid zinc during isothermal relaxation: A molecular dynamics simulation study

    NASA Astrophysics Data System (ADS)

    Zhou, Li-Li; Liu, Rang-Su; Tian, Ze-An; Liu, Hai-Rong; Hou, Zhao-Yang; Peng, Ping

    2016-08-01

    The crystallization characteristics in supercooled liquid Zn during isothermal relaxation were investigated using molecular dynamics simulations by adopting the cluster-type index method (CTIM) and the tracing method. Results showed that the crystallization process undergo three different stages. The size of the critical nucleus was found to be approximately 90–150 atoms in this system; the growth of nuclei proceeded via the successive formation of hcp and fcc structures with a layered distribution; and finally, the system evolved into a much larger crystal with a distinct layered distribution of hcp and fcc structures with an 8R stacking sequence of ABCBACAB by adjusting all of the atoms in the larger clusters according to a certain rule.

  9. [Study on phosphorus adsorption characteristic of sediments in an ecological ditch].

    PubMed

    Zhang, Shu-Nan; Jia, Zhao-Yue; Xiao, Run-Lin; Yang, Feng-Fei; Yu, Hong-Bing; Liu, Feng; Wu, Jin-Shui

    2013-03-01

    Sediments properties and phosphorus (P) adsorption capacities were compared among the samples of 0-5 cm and 5-15 cm layers from the ecological ditch vegetated with Cenetlla asiatica, Sparganium stoloniferum and a natural agricultural ditch with weeds. The results showed the 0-5 cm sediment vegetated with Cenetlla asiatica had higher concentrations of oxalate extracted Fe, Al and P than those vegetated with Sparganium stoloniferum or weeds. The parameters calculated from the Freudlich and Langmiur isotherms showed the equilibrium phosphate concentration (EPC0) ranged from 0.009 to 0.031 mg x L(-1). Cenetlla asiatica in the 0-5 cm layer had the maximum values of 352.2 L x kg(-1) and 562.7 mg x kg(-1) for Freundlich adsorption constant (K(f)) and Langmuir sorption maximum (S(max)), respectively, which proved it had the highest P adsorption capacity. The regression analysis showed P sorption parameters had significant relationship to oxalate-extracted Fe, clay content and DPS (P < 0.05). It was thus clear that aquatic plants influenced sediment properties and P adsorption capacity, and the practice of growing proper plants in ecological ditch could reduce the risk of P loss in non-point source pollution.

  10. Arsenic Adsorption Equilibrium Concentration and Adsorption Rate of Activated Carbon Coated with Ferric-Aluminum Hydroxides

    NASA Astrophysics Data System (ADS)

    Zhang, M.; Sugita, H.; Oguma, T.; Hara, J.; Takahashi, S.

    2015-12-01

    In some areas of developing countries, ground or well water contaminated with arsenic has been reluctantly used as drinking water. It is highly desirable that effective and inexpensive arsenic removal agents should be developed and provided to reduce the potential health risk. Previous studies demonstrated that activated carbon coated with ferric-aluminum hydroxides (Fe-Al-C) has high adsorptive potential for removal of arsenic. In this study, a series of experiments using Fe-Al-C were carried to discuss adsorption equilibrium time, adsorption equilibrium concentration and adsorption rate of arsenic for Fe-Al-C. Fe-Al-C used in this study was provided by Astec Co., Ltd. Powder reagent of disodium hydrogen arsenate heptahydrate was dissolved into ion-exchanged water. The solution was then further diluted with ion-exchanged water to be 1 and 10 mg/L as arsenic concentration. The pH of the solution was adjusted to be around 7 by adding HCl and/or NaOH. The solution was used as artificial arsenic contaminated water in two types of experiments (arsenic adsorption equilibrium and arsenic adsorption rate tests). The results of the arsenic equilibrium tests were showed that a time period of about 3 days to reach apparent adsorption equilibrium for arsenic. The apparent adsorption equilibrium concentration and adsorbed amount of arsenic on Fe-Al-C adsorbent could be estimated by application of various adsorption isotherms, but the distribution coefficient of arsenic between solid and liquid varies with experimental conditions such as initial concentration of arsenic and addition concentration of adsorbent. An adsorption rate equation that takes into account the reduction in the number of effective adsorption sites on the adsorbent caused by the arsenic adsorption reaction was derived based on the data obtained from the arsenic adsorption rate tests.

  11. Adsorption of a multicomponent rhamnolipid surfactant to soil

    SciTech Connect

    Noordmann, W.H.; Brusseau, M.L.; Janssen, D.B.

    2000-03-01

    The adsorption of rhamnolipid, a multicomponent biosurfactant with potential application in soil remediation, to two sandy soils was investigated using batch and column studies. The surfactant mixture contained six anionic components differing in lipid chain length and number of rhamnose moieties. Batch adsorption experiments indicated that the overall adsorption isotherms of total surfactant and of the individual components leveled off above a concentration at which micelles were formed. Column experiments showed that the retardation factors for the total surfactant and for the individual components decreased with increasing influent concentration. Extended tailing was observed in the distal portion of the surfactant breakthrough curve. The concentration-dependent retardation factors and the extended tailing are in accordance with the nonlinear (concave) adsorption isotherms found in the batch adsorption studies. The more hydrophobic rhamnolipid components were preferentially adsorbed, but adsorption was not correlated with the organic carbon content of the soil. This suggests that adsorption of rhamnolipid to soil is not a partitioning process but mainly an interfacial adsorption process.

  12. Ceria and titania incorporated silica based catalyst prepared from rice husk: adsorption and photocatalytic studies of methylene blue.

    PubMed

    Adam, Farook; Muniandy, Lingeswarran; Thankappan, Radhika

    2013-09-15

    Titania and ceria incorporated rice husk silica based catalyst was synthesized via sol-gel method using CTAB and glycerol as surface directing agents at room temperature and labeled as RHS-50Ti10Ce. The catalyst was used to study the adsorption and photodegradation of methylene blue (MB) under UV irradiation. The powder XRD pattern of RHS-50Ti10Ce was much broader (2θ=25-30°) than that of the parent RHS (2θ=22°). The catalyst exhibited type IV isotherm with H3 hysteresis loop, and the TEM images showed partially ordered pore arrangements. The TGA-DTG thermograms confirmed the complete removal of the templates after calcination at 500°C. RHS-50Ti10Ce exhibited excellent adsorption capability with more than 99% removal of MB from a 40 mg L(-1) solution in just 15 min. It also decolorized an 80 mg L(-1) MB solution under UV irradiation in 210 min, which was comparable with the commercialized pure anatase TiO2.

  13. Adsorption of sodium dodecyl sulfate and sodium dodecyl phosphate on aluminum, studied by QCM-D, XPS, and AAS.

    PubMed

    Karlsson, Philip M; Palmqvist, Anders E C; Holmberg, Krister

    2008-12-01

    The adsorption of two anionic surfactants, sodium dodecyl sulfate (SDS) and sodium dodecyl phosphate (SDP), at surfaces of aluminum and aluminum oxide has been studied by means of atomic absorption spectrometry (AAS), X-ray photoelectron spectroscopy (XPS), and quartz crystal microbalance with dissipation monitoring (QCM-D). It was shown that more SDP than SDS binds to the surface and that SDP prevents dissolution of aluminum in water whereas SDS does not. This was not obvious, since the adsorption isotherms of the two surfactants to aluminum pigment powder are quite similar, as shown in an earlier work. The decreased aluminum dissolution with SDP compared to SDS was explained by the formation of a more compact protective layer with less permeability on the aluminum surface with SDP than with SDS. This is explained by differences in complexing ability between the surfactants and the aluminum pigment surface. While SDP is expected to form an inner-sphere complex with aluminum, leading to a lower accessibility of aluminum sites to water, SDS is likely to form a weaker outer-sphere complex.

  14. Adsorption of 2,4-Dichlorophenoxyacetic Acid from an Aqueous Solution on Fly Ash.

    PubMed

    Kuśmierek, Krzysztof; Świątkowski, Andrzej

    2016-03-01

    The adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) on fly ash was studied. The effects of adsorbent dose, contact time, pH, ionic strength, and temperature on the adsorption were investigated. Adsorption kinetic data were analyzed using pseudo-first and pseudo-second order models, and results showed that adsorption kinetics were better represented by the pseudo-second order model. Adsorption isotherms of 2,4-D on fly ash were analyzed using the Freundlich and Langmuir models. Thermodynamic parameters (ΔG°, ΔH°, and ΔS°) indicated that the adsorption process was spontaneous and endothermic. The negative values of ΔG° and the positive value of ΔH° indicate the spontaneous nature of 2,4-D adsorption on fly ash, and that the adsorption process was endothermic. Results showed that fly ash is an efficient, low-cost adsorbent for removal of 2,4-D from water.

  15. Preparation of adsorbent with magnesium sulfate and straw pulp black liquor and its phenol adsorption properties

    NASA Astrophysics Data System (ADS)

    Guo, Lugang; Wang, Haizeng

    2009-09-01

    A magnesia adsorbent was prepared from straw pulp black liquor and magnesium sulfate for the first time, and its adsorption of phenol from aqueous solution was examined. The characteristics of the adsorbent were tested through chemical analysis, surface analysis, X-ray diffraction and FT-IR spectroscopy. The effects of various factors, such as dose, adsorption time and adsorption temperature, on phenol adsorption behavior were studied. The results show that the adsorption processes can be fitted to the isotherm Langmuir model very well. It was found that the adsorption process was strongly influenced by temperature and the optimal temperature for phenol removal was 40 °C. The optimum adsorption time was 10 min, and desorption would happen afterwards. Between the models of Langmuir and Freundlich, the adsorption process of phenol onto magnesia fitted the Langmuir equation better.

  16. Temperature-dependent infrared and calorimetric studies on arsenicals adsorption from solution to hematite nanoparticles

    Technology Transfer Automated Retrieval System (TEKTRAN)

    To address the lack of systematic and surface sensitive studies on the adsorption energetics of arsenic compounds on metal (oxyhydr)oxides, we conducted temperature-dependent ATR-FTIR studies for the adsorption of arsenate, monomethylarsonic acid, and dimethylarsinic acid on hematite nanoparticles a...

  17. Adsorption-desorption behavior of thiram onto humic acid.

    PubMed

    Filipe, O M S; Vidal, M M; Duarte, A C; Santos, E B H

    2009-06-10

    The adsorption/desorption behavior of pure thiram (Thi-P) and formulated thiram (Thi-F) onto commercial humic acids (HA) was studied using a batch equilibration procedure. Results of adsorption kinetic experiments showed that thiram adsorption is a fast process since 85% of the equilibrium concentration is reached within two hours. Experimental K(D) values between 0.110 to 0.210 L g(-1) were obtained for the adsorption of both Thi-P and Thi-F onto HA, suggesting that thiram is strongly sorbed by humic acids. In general, for both Thi-P and Thi-F, the lower the initial thiram concentration, the stronger is its adsorption (higher K(D) and percentage adsorption values). The adsorption isotherms were found to match the BET model. The results show that thiram adsorption onto condensed humic acids cannot be explained only in terms of specific interactions, such as those identified in studies of adsorption of thiram with humic acids in solution. The comparison of sorption and desorption results allowed the observation of hysteresis phenomena. Desorption K(D) values were consistently higher than those for adsorption at the same equilibrium concentration. Hysteresis was lower for the formulated thiram suggesting that adsorption is more reversible in the presence of the formulation components turning the pesticide more susceptible to be leached.

  18. [Comparison study on adsorption of middle molecular substances with multiwalled carbon nanotubes and activated carbon].

    PubMed

    Li, Guifeng; Wan, Jianxin; Huang, Xiangqian; Zeng, Qiao; Tang, Jing

    2011-08-01

    In recent years, multi-walled carbon nanotubes (MWCTs) are very favorable to the adsorption of middle molecular substances in the hemoperfusion because of their multiporous structure, large surface area and high reactivity, which are beneficial to the excellent absorption properties. The purpose of this study was to study the MWCTs on the adsorption capacity of the middle molecular substances. Vitamin B12 (VB12) was selected as a model of the middle molecular substances. The morphologies of MWCTs and activated carbon from commercial "carbon kidney" were observed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The adsorption behavior of VB12 was compared to each other with UV-visible absorption spectra. The MWCTs formed a sophistaicate gap structure, and compared to the activated carbon, MWCTs had a larger surface area. By Langmuir equation and Freundlich equation fitting analysis, VB12 adsorption on MWCTs is fit for multi-molecular layer adsorption, and the adsorption type of activated carbon is more inclined to the model corresponding to Langmuir monolayer adsorption. The adsorption rate of MWCTs is faster than that of the activated carbon and the adsorption capacity is greater, which could be expected to become the new adsorbent in the hemoperfusion. PMID:21936376

  19. Comparative study of tributyltin adsorption onto mesoporous silica functionalized with calix[4]arene, p-tert-butylcalix[4]arene and p-sulfonatocalix[4]arene.

    PubMed

    Alahmadi, Sana; Mohamad, Sharifah; Maah, Mohd Jamil

    2014-01-01

    The adsorption of tributyltin (TBT), onto three mesoporous silica adsorbents functionalized with calix[4]arene, p-tert-butylcalix[4]arene and p-sulfonatocalix[4]arene (MCM-TDI-C4, MCM-TDI-PC4 and MCM-TDI-C4S, respectively) has been compared. Batch adsorption experiments were carried out and the effect of contact time, initial TBT concentration, pH and temperature were studied. The Koble-Corrigan isotherm was the most suitable for data fitting. Based on a Langmuir isotherm model, the maximum adsorption capacities were 12.1212, 16.4204 and 7.5757 mg/g for MCM-TDI-C4, MCM-TDI-PC4 and MCM-TDI-C4S, respectively. The larger uptake and stronger affinity of MCM-TDI-PC4 than MCM-TDI-C4 and MCM-TDI-C4S probably results from van der Waals interactions and the pore size distribution of MCM-TDI-PC4. Gibbs free energies for the three adsorption processes of TBT presented a negative value, reflecting that TBT/surface interactions are thermodynamic favorable and spontaneous. The interaction processes were accompanied by an increase of entropy value for MCM-TDI-C4 and MCM-TDI-C4S (43.7192 and 120.7609 J/mol K, respectively) and a decrease for MCM-TDI-PC4 (-37.4704 J/mol K). It is obviously observed that MCM-TDI-PC4 spontaneously adsorbs TBT driven mainly by enthalpy change, while MCM-TDI-C4 and MCM-TDI-C4S do so driven mainly by entropy changes. PMID:24727422

  20. Comparative study of tributyltin adsorption onto mesoporous silica functionalized with calix[4]arene, p-tert-butylcalix[4]arene and p-sulfonatocalix[4]arene.

    PubMed

    Alahmadi, Sana; Mohamad, Sharifah; Maah, Mohd Jamil

    2014-04-10

    The adsorption of tributyltin (TBT), onto three mesoporous silica adsorbents functionalized with calix[4]arene, p-tert-butylcalix[4]arene and p-sulfonatocalix[4]arene (MCM-TDI-C4, MCM-TDI-PC4 and MCM-TDI-C4S, respectively) has been compared. Batch adsorption experiments were carried out and the effect of contact time, initial TBT concentration, pH and temperature were studied. The Koble-Corrigan isotherm was the most suitable for data fitting. Based on a Langmuir isotherm model, the maximum adsorption capacities were 12.1212, 16.4204 and 7.5757 mg/g for MCM-TDI-C4, MCM-TDI-PC4 and MCM-TDI-C4S, respectively. The larger uptake and stronger affinity of MCM-TDI-PC4 than MCM-TDI-C4 and MCM-TDI-C4S probably results from van der Waals interactions and the pore size distribution of MCM-TDI-PC4. Gibbs free energies for the three adsorption processes of TBT presented a negative value, reflecting that TBT/surface interactions are thermodynamic favorable and spontaneous. The interaction processes were accompanied by an increase of entropy value for MCM-TDI-C4 and MCM-TDI-C4S (43.7192 and 120.7609 J/mol K, respectively) and a decrease for MCM-TDI-PC4 (-37.4704 J/mol K). It is obviously observed that MCM-TDI-PC4 spontaneously adsorbs TBT driven mainly by enthalpy change, while MCM-TDI-C4 and MCM-TDI-C4S do so driven mainly by entropy changes.

  1. Water vapor adsorption on activated carbon preadsorbed with naphtalene.

    PubMed

    Zimny, T; Finqueneisel, G; Cossarutto, L; Weber, J V

    2005-05-01

    The adsorption of water vapor on a microporous activated carbon derived from the carbonization of coconut shell has been studied. Preadsorption of naphthalene was used as a tool to determine the location and the influence of the primary adsorbing centers within the porous structure of active carbon. The adsorption was studied in the pressure range p/p0=0-0.95 in a static water vapor system, allowing the investigation of both kinetic and equilibrium experimental data. Modeling of the isotherms using the modified equation of Do and Do was applied to determine the effect of preadsorption on the mechanism of adsorption. PMID:15797395

  2. A DFT study of formaldehyde adsorption on functionalized graphene nanoribbons

    NASA Astrophysics Data System (ADS)

    Maaghoul, Zohreh; Fazileh, Farhad; Kakemam, Jamal

    2015-02-01

    Density functional theory (DFT) based ab initio calculations were done to monitor the formaldehyde (CHOH) adsorptive behavior on pristine and Ni-decorated graphene sheet. Structural optimization indicates that the formaldehyde molecule is physisorbed on the pristine sheet via partly weak van der Waals attraction having the adsorption energy of about -15.7 kcal/mol. Metal decorated sheet is able to interact with the CHOH molecule, so that single Ni atoms prefer to bind strongly at the bridge site of graphene and each metal atom bound on sheet may adsorb up to four CHOH. The findings also show that the Ni decoration on graphene surface results in some changes in electronic properties of the sheet and its Eg is remained unchanged after adsorption of CHOH molecules. It is noteworthy to say that no bond cleavage was observed for the adsorption of CHOH on Ni-decorated graphene.

  3. Protein adsorption to organosiloxane surfaces studied by acoustic wave sensor.

    PubMed

    Cavic, B A; Thompson, M

    1998-10-01

    Surfaces of the two organosiloxanes, polymercaptopropylmethylsiloxane and octaphenylcyclotetrasiloxane, were prepared on the gold electrodes of thickness-shear mode acoustic wave sensors. Compounds containing the siloxane bond are important in the fabrication of medical implants. The flow-through adsorption of the proteins: human serum albumin, alpha-chymotripsinogen A, cytochrome c, fibrinogen, hemoglobin, immunoglobulin G and apo-transferrin to the two siloxane surfaces and a gold electrode were detected by acoustic network analysis. With the exception of minor wash-off by buffer flow, the adsorption of all proteins to the three surfaces is irreversible. Differences observed for the magnitudes of adsorption for the various cases are ascribed to the role played by molecular interactions at the liquid/solid interface. The results confirm that changes in series resonant frequencies caused by macromolecular adsorption differ significantly from the widely accepted "mass based" model usually employed to characterize the response of this type of acoustic wave device.

  4. Study of Adsorption of Copper Species onto Multiwall Carbon Nanotubes

    EPA Science Inventory

    Functionalized CNTs have improved adsorptive capacities over pristine CNTs. These can be used for sensors, membranes, filters and matrix composite enhancements made possible because of their nano-size.

  5. The Extent of Reversibility of Polychlorinated Biphenyl Adsorption

    EPA Science Inventory

    The extent of reversibility of PCB bonding to sediments has been characterized in studies on the partitioning behavior of a hexachlorobiphenyl isomer. Linear non-singular isotherms have been observed for the adsorption and desorption of 2.4.5.2?,4?,5? hexachlorobiphenyl (HCBP) to...

  6. Adsorption of methylene blue onto sonicated sepiolite from aqueous solutions.

    PubMed

    Küncek, Ilknur; Sener, Savaş

    2010-01-01

    The aim of the present study is to enhance the methylene blue (MB) adsorption of sepiolite by ultrasonic treatment. The natural sepiolite was pretreated by sonication to improve the surface characteristics and enhance the dye uptake capacity. Sonication process resulted in a significant increase in the specific surface area (SSA) of sepiolite. The FTIR spectrum of the sonicated sepiolite indicates that the tetrahedral sheet is probably distorted after sonication process. The effect of various parameters such as sonication, pH, initial dye concentration and temperature on dye adsorption has been investigated. The adsorbed amount of MB on sepiolite increased after sonication as well as with increasing pH and temperature. The experimental data were evaluated by applying the pseudo-first- and second-order, and the intraparticle diffusion adsorption kinetic models. Adsorption process of MB onto sepiolite followed the pseudo-second-order rate expression. The experimental data were analyzed by Langmuir and Freundlich isotherms, and found that the isotherm data were reasonably well correlated by Langmuir isotherm. Maximum monolayer adsorption capacity of sepiolite for MB increased from 79.37 to 128.21 mg/g after the sonication. Various thermodynamic parameters, such as Delta G(0), Delta H(0) and DeltaS(0) were calculated. The thermodynamics of MB/sepiolite system indicated spontaneous and endothermic nature of the process. Adsorption measurements showed that the process was very fast and physical in nature.

  7. Quantum chemical studies of trace gas adsorption on ice nanoparticles

    NASA Astrophysics Data System (ADS)

    Schrems, Otto; Ignatov, Stanislav K.; Gadzhiev, Oleg B.; Masunov, Artem E.

    2013-04-01

    We have investigated the interaction of atmospheric trace gases with crystalline water ice particles of nanoscale size by modern quantum chemical methods. Small ice particles which can be formed in different altitudes play an important role in chemistry and physics of the Earth atmosphere. Knowledge about the uptake and incorporation of atmospheric trace gases in ice particles as well as their interactions with water molecules is very important for the understanding of processes at the air/ice interface. The interaction of the atmospheric trace gases with atmospheric ice nanoparticles is also an important issue for the development of modern physicochemical models. Usually, the interactions between trace gases and small particles considered theoretically apply small-size model complexes or the surface models representing only fragments of the ideal surface. Ice particles consisting of 48, 72, 216 and 270 water molecules with a distorted structure of hexagonal water ice Ih were studied using the new SCC-DFTBA method combining well the advantages of the DFT theory and semiempirical methods of quantum chemistry. The largest clusters correspond to the minimal nanoparticle size which are considered to be crystalline as determined experimentally. The clusters up to (H2O)72 were studied at the B3LYP/6-31++G(d,p) and B3LYP/6-311++G(2d,2p) levels. The larger clusters were studied using DFTBA and DFTB+ methods. Several adsorption complexes for the (H2O)270 water ice cluster were optimized at the RI-BLYP/6-31+G(d) theory level to verify the DFTB+ results. Trace gas molecules were coordinated on different sites of the nanoparticles corresponding to different ice Ih crystal planes: (0001), (10-10), (11-20). As atmospheric trace gases we have chosen CO, CO2, HCO*, HCOH*, HCHO, HCOOH and (HCO)2. which are the possible products and intermediates of the UV photolysis of organic molecules such as HCHCHO adsorbed on the ice surface. The structures of the corresponding coordination

  8. Removal of Cr(VI) from aqueous solution by adsorption onto activated carbon.

    PubMed

    Selvi, K; Pattabhi, S; Kadirvelu, K

    2001-10-01

    Activated carbon (AC) prepared from coconut tree sawdust was used as an adsorbent for the removal of Cr(VI) from aqueous solution. Batch mode adsorption studies were carried out by varying agitation time, initial Cr(VI) concentration, carbon concentration and pH. Langmuir and Freundlich adsorption isotherms were applied to model the adsorption data. Adsorption capacity was calculated from the Langmuir isotherm and was 3.46 mg/g at an initial pH of 3.0 for the particle size 125-250 microm. The adsorption of Cr(VI) was pH dependent and maximum removal was observed in the acidic pH range. Desorption studies were carried out using 0.01-1 M NaOH solutions.

  9. Adsorption of surfactants on mineral oxide surfaces from aqueous solutions. Part 1. Isomerically pure anionic surfactants

    SciTech Connect

    Scamehorn, J.F.; Schechter, R.S.; Wade, W.H.

    1982-02-01

    The adsorption of surfactants on minerals is detrimental to surfactant-enhanced oil recovery. To minimize adsorption, the forces tending to cause it must be understood. This requires the study of relatively simple, well-defined systems. The majority of surfactant adsorption studies on mineral oxides has been made with surfactant mixtures and not with monoisomerically pure species. Some of the observed results may be due to complex surfactant intercomponent interactions. In this study, the adsorption of 3 isomerically pure alkylbenzene sulfonates was measured on alumina and kaolinite from very low concentrations to well above the critical micelle concentration and a thermodynamic model was developed, which describes the observed isotherms. 59 references.

  10. Thermodynamics of cationic lipid-DNA complex formation as studied by isothermal titration calorimetry.

    PubMed Central

    Pozharski, Edwin; MacDonald, Robert C

    2002-01-01

    The detailed analysis of the cationic lipid-DNA complex formation by means of isothermal titration calorimetry is presented. Most experiments were done using 1,2-dioleyl-sn-glycero-3-ethylphosphocholine (EDOPC), but basic titrations were also done using DOTAP, DOTAP:DOPC, and DOTAP:DOPE mixtures. Complex formation was endothermic with less than 1 kcal absorbed per mole of lipid or DNA charge. This enthalpy change was attributed to DNA-DNA mutual repulsion within the lamellar complex. The exception was DOTAP:DOPE-containing lipoplex for which the enthalpy of formation was exothermic, presumably because of DOPE amine group protonation. Experimental conditions, namely, direction and titration increment as well as concentration of titrant, which dictate the structure of resulting lipoplex (whether lamellar complex or DNA-coated vesicle), were found to affect the apparent thermodynamics of complex formation. The structure, in turn, influences the biological properties of the lipoplex. If the titration of lipid into DNA was carried out in large increments, the DeltaH was larger than when the injection increments were smaller, a finding that is consistent with increased vesicle disruption under large increments and which is expected theoretically. Cationic lipid-DNA binding was weak in high ionic strength solutions, however, the effective binding constant is within micromolar range because of macromolecular nature of the interaction. PMID:12080142

  11. Metal adsorption on mosses: Toward a universal adsorption model.

    PubMed

    González, A G; Pokrovsky, O S

    2014-02-01

    This study quantifies the adsorption of heavy metals on 4 typical moss species used for environmental monitoring in the moss bag technique. The adsorption of Cu(2+), Cd(2+), Ni(2+), Pb(2+) and Zn(2+) onto Hypnum sp., Sphagnum sp., Pseudoscleropodium purum and Brachytecium rutabulum has been investigated using a batch reactor in a wide range of pH (1.3-11.0) and metal concentrations in solution (1.6μM-3.8mM). A Linear Programming Model (LPM) was applied for the experimental data to derive equilibrium constants and the number of surface binding sites. The surface acid-base titration performed for 4 mosses at a pH range of 3-10 in 0.1M NaNO3 demonstrated that Sphagnum sp. is the most efficient adsorbent as it has the maximal number of proton-binding sites on the surface (0.65mmol g(-1)). The pKa computed for all the moss species suggested the presence of 5 major functional groups: phosphodiester, carboxyl, phosphoryl, amine and polyphenols. The results of pH-edge experiments demonstrated that B. rutabulum exhibits the highest percentage of metal adsorption and has the highest number of available sites for most of the metals studied. However, according to the results of the constant pH "Langmuirian" isotherm, Sphagnum sp. can be considered as the strongest adsorbent, although the relative difference from other mosses is within 20%. The LPM was found to satisfactorily fit the experimental data in the full range of the studied solution parameters. The results of this study demonstrate a rather similar pattern of five metal adsorptions on mosses, both as a function of pH and as a metal concentration, which is further corroborated by similar values of adsorption constants. Therefore, despite the species and geographic differences between the mosses, a universal adsorption edge and constant pH adsorption isotherm can be recommended for 4 studied mosses. The quantitative comparison of metal adsorption with other common natural organic and inorganic materials demonstrates

  12. Systematic DFT-GGA study of hydrogen adsorption on transition metals

    NASA Astrophysics Data System (ADS)

    Vasić, D.; Ristanović, Z.; Pašti, I.; Mentus, S.

    2011-12-01

    Computational study of hydrogen adsorption on (111) surface of transition metals with face centered cubic (fcc) lattice is reported and the results are compared with available experimental and theoretical data. In addition, dissociative adsorption of hydrogen on Pt(111), Pt(100) and Pt(110) is studied in the range of coverage from 0.25 to 1 monolayer. In the case of Pt(111) preferential adsorption site was found to be three-coordinated fcc-hollow site, while on Pt(100) and Pt(110) surface hydrogen settles on two-coordinated bridge and short bridge site, respectively. Hydrogen adsorption energy was found to decrease with the increasing coverage. Structural changes of studied Pt surfaces upon hydrogen adsorption have been compared with the experimental data existing in the literature and good qualitative agreement has been obtained.

  13. Molecular Simulation studies of adsorption of polymers on non-planar surfaces: Influence of surface characteristics

    NASA Astrophysics Data System (ADS)

    Venkatakrishnan, Abishek; Shim, Anne; Frost, Aquil; Lewnard, John; Kuppa, Vikram

    2015-03-01

    Molecular simulations are employed to investigate the adsorption of freely rotating polymer chains adsorbing on to non-planar surfaces. Adsorption studies on planar surfaces have been studied extensively and fairly well understood. However, in reality, surfaces are non-planar and cannot be represented using smooth surface models. We investigate the effect of surface characteristics on adsorption via molecular dynamics and Monte Carlo molecular simulations in the NVT ensemble. Both regular (uniform) and irregular (self-affine) roughness parameters are studied. The adsorbed polymer chains are characterized by density and orientation profiles, adsorbed fraction and chain topologies. Our results elucidate the extent to which surface roughness influences adsorption, in competition with other factors such as chain length and monomer-surface interaction. We also demonstrate how both adsorption and desorption can be controlled solely by tuning surface inhomogeneities.

  14. Fruit waste adsorbent for ammonia nitrogen removal from synthetic solution: Isotherms and kinetics

    NASA Astrophysics Data System (ADS)

    Zahrim, AY; Lija, Y.; Ricky, L. N. S.; Azreen, I.

    2016-06-01

    In this study, four types of watermelon rind (WR) adsorbents; fresh WR, modified WR with sodium hydroxide (NaOH), potassium hydroxide (KOH) and sulphuric acid (H2SO4) were used as a potential low-cost adsorbent to remove NH3-N from solution. The adsorption data were fitted with the adsorption isotherm and kinetic models to predict the mechanisms and kinetic characteristics of the adsorption process. The equilibrium data agreed well with Langmuir isotherm model with highest correlation (R2=1.00). As for kinetic modelling, the adsorption process follows pseudo-second order for all four types of adsorbents which has R2 value of 1.0 and calculated adsorption capacity, Qe of 1.2148mg/g. The calculated Qe for pseudo-second order has the smallest difference with the experimental Qe and thus suggest that this adsorption process is mainly governed by chemical process involving cations sharing or exchange between WR adsorbent and NH3-N in the solution.

  15. Effect of aniline on cadmium adsorption by sulfanilic acid-grafted magnetic graphene oxide sheets.

    PubMed

    Hu, Xin-jiang; Liu, Yun-guo; Zeng, Guang-ming; Wang, Hui; Hu, Xi; Chen, An-wei; Wang, Ya-qin; Guo, Yi-Mming; Li, Ting-ting; Zhou, Lu; Liu, Shao-heng; Zeng, Xiao-xia

    2014-07-15

    Cd(II) has posed severe health risks worldwide. To remove this contaminant from aqueous solution, the sulfanilic acid-grafted magnetic graphene oxide sheets (MGOs/SA) were prepared and characterized. The mutual effects of Cd(II) and aniline adsorption on MGOs/SA were studied. The effects of operating parameters such as pH, ionic strength, contact time and temperature on the Cd(II) enrichment, as well as the adsorption kinetics and isotherm were also investigated. The results demonstrated that MGOs/SA could effectively remove Cd(II) and aniline from the aqueous solution and the two adsorption processes were strongly dependent on solution pH. The Cd(II) adsorption was reduced by the presence of aniline at pH<5.4 but was improved at pH>5.4. The presence of Cd(II) diminished the adsorption capacity for aniline at pH<7.8 but enhanced the aniline adsorption at pH>7.8. The decontamination of Cd(II) by MGOs/SA was influenced by ionic strength. Besides, the adsorption process could be well described by pseudo-second-order kinetic model. The intraparticle diffusion study revealed that the intraparticle diffusion was not the only rate-limiting step for the adsorption process. Moreover, the experimental data of isotherm followed the Freundlich isotherm model.

  16. Studies on preparing and adsorption property of grafting terpolymer microbeads of PEI-GMA/AM/MBA for bilirubin.

    PubMed

    Gao, Baojiao; Lei, Haibo; Jiang, Liding; Zhu, Yong

    2007-06-15

    Crosslinking copolymer microbeads with a diameter range of 100-150 microm were synthesized by suspension copolymerization of glycidyl methacrylate (GMA), acrylamide (AM) and N,N'-methylene bisacrylamide (MBA). Subsequently, polyethyleneimine (PEI) was grafted on the surfaces of the terpolymer microbeads GMA/AM/MBA via the ring-opening reaction of the epoxy groups, and the grafting microbeads PEI-GMA/AM/MBA were prepared. In this paper, the adsorption property of the grafting microbeads for bilirubin was mainly investigated, and the effects of various factors, such as pH value, ionic strength and grafting degree of PEI on the surface of grafting microbeads and the adsorption capacity of the grafting microbeads for bilirubin were examined. The batch adsorption experiment results show that by right of the action of grafted polyamine macromolecules PEI, the grafting microbeads PEI-GMA/AM/MBA have quite strong adsorption ability for bilirubin; the isotherm adsorption conforms to Freundlich equation. The pH value of the medium affects the adsorption capacity greatly, As in the nearly neutral solutions with pH 6, the grafting microbeads have the strongest adsorption ability for bilirubin, whereas in acidic and basic solutions their adsorption ability is weak. The ionic strength hardly affects the adsorption ability of the grafting microbeads. The grafting degree of PEI on the surfaces of the grafting microbeads also has a great effect on the adsorption capacity, and higher the grafting degree of PEI on the surface of the microbead PEI-GMA/AM/MBA, the stronger is the adsorption ability of the microbeads.

  17. DFT studies of the phenol adsorption on boron nitride sheets.

    PubMed

    Hernández, Jose Mario Galicia; Cocoletzi, Gregorio Hernández; Anota, Ernesto Chigo

    2012-01-01

    We perform first principles total energy calculations to investigate the atomic structures of the adsorption of phenol (C(6)H(5)OH) on hexagonal boron nitride (BN) sheets. Calculations are done within the density functional theory as implemented in the DMOL code. Electron-ion interactions are modeled according to the local-spin-density-approximation (LSDA) method with the Perdew-Wang parametrization. Our studies take into account the hexagonal h-BN sheets and the modified by defects d-BN sheets. The d-BN sheets are composed of one hexagon, three pentagons and three heptagons. Five different atomic structures are investigated: parallel to the sheet, perpendicular to the sheet at the B site, perpendicular to the sheet at the N site, perpendicular to the central hexagon and perpendicular to the B-N bond (bridge site). To determine the structural stability we apply the criteria of minimum energy and vibration frequency. After the structural relaxation phenol molecules adsorb on both h-BN and d-BN sheets. Results of the binding energies indicate that phenol is chemisorbed. The polarity of the system increases as a consequence of the defects presence which induces transformation from an ionic to covalent bonding. The elastic properties on the BN structure present similar behavior to those reported in the literature for graphene. PMID:21523546

  18. First principles study of hydrogen adsorption on carbon nanowires.

    NASA Astrophysics Data System (ADS)

    Tapia, Alejandro; Aguilera, Luis; Murrieta, Gabriel; de Coss, Romeo

    2007-03-01

    Recently has been reported a new type of one-dimensional carbon structures. Carbon nanowires formed by a linear carbon-atom chain inside an armchair (5,5) carbon nanotube has been observed using high-resolution transmission electron microscopy. In the present work we have studied the changes in the electronic structure of a carbon nanowires and (5,5) single-walled carbon nanotubes (SWCN) when a hydrogen atom is adsorbed. We used the Density Functional Theory and the calculations where performed by the pseudopotentials LCAO method (SIESTA code) and the Generalized Gradient Approximation (GGA) for the exchange-correlation potential. We have analyzed the changes in the atomic structure, density of states (LDOS), and the local orbital population. We found charge transfer from the nanotube to the linear chain and the hydrogen atom, the electronic character of the chain and nanotube sub-systems in chain@SWCN is the same that in the corresponding isolated systems, chain or SWCN. But the hydrogen adsorption produced changes in the atomic estructure and the electronic properties. This research was supported by PRIORI-UADY under Grant No. FING-05-004 and Consejo Nacional de Ciencia y Tecnolog'ia (Conacyt) under Grants No. 43830-F and 49985-J.

  19. A Study of DNA Adsorption Kinetics on OTS Surfaces

    NASA Astrophysics Data System (ADS)

    Barone, Joseph; Fang, Xiaohua; Li, Bingquan; Seo, Young-Soo; Samuilov, Vladimir; Rafailovich, Miriam; Sokolov, Jonathan

    2003-03-01

    The evaporation kinetics of droplets containing DNA were studied as a function of DNA molecular weight, DNA concentration, and buffer concentration.The contact angle and overall droplet morphology were observed using a KSV contact angle goniometer as a function of time. Simultaneously, the DNA distribution and adsorption kinetics were measured with confocal microscopy. The DNA droplets were deposited on hydrophobic OTS-covered silicon surfaces and stained with ethidium bromide solution. Up to three stages were found during DNA droplet drying process, depending on the DNA concentration. The results also show that a ring is formed at the air/solid /liquid interface in a manner similar to that reported for a colloidal suspension by Robert D. Deegan et.a. [Physical Review E, Vol 62, No.1, July 2000, p756-765] The absorbed amount of DNA was obtained by measuring the intensity in the ring. The dynamics and DNA morphology are affected by both the molecular weight and the DNA concentration. Supported by NSF-MRSEC program (DMR-9632525)

  20. Adsorption behavior of activated carbon derived from pyrolusite-modified sewage sludge: equilibrium modeling, kinetic and thermodynamic studies.

    PubMed

    Chen, Yao; Jiang, Wenju; Jiang, Li; Ji, Xiujuan

    2011-01-01

    Activated carbon was developed from sewage sludge using pyrolusite as an additive. It was demonstrated that the removal efficiency of two synthetic dyes (Tracid orange GS and Direct fast turquoise blue GL) by the produced adsorbent was up to 97.6%. The activated carbon with pyrolusite addition had 38.2% higher surface area, 43.8% larger micropore and 54.4% larger mesopore production than ordinary sludge-based activated carbons. Equilibrium adsorption isotherms and kinetics were also investigated based on dyes adsorption tests. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption, and the results fitted well to the Langmuir isotherm. The kinetic data have been analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion equation. The experimental data fitted very well with pseudo-second-order kinetic model. Activation energies for the adsorption processes ranged between 8.7 and 19.1 kJ mol 1. Thermodynamic parameters such as standard free energy (deltaG0), standard enthalpy (deltaH0) and standard entropy (deltaS0) were evaluated. The adsorption of these two dyes on the activated carbon was found to be a spontaneous and endothermic process in nature.

  1. Adsorption behavior of activated carbon derived from pyrolusite-modified sewage sludge: equilibrium modeling, kinetic and thermodynamic studies.

    PubMed

    Chen, Yao; Jiang, Wenju; Jiang, Li; Ji, Xiujuan

    2011-01-01

    Activated carbon was developed from sewage sludge using pyrolusite as an additive. It was demonstrated that the removal efficiency of two synthetic dyes (Tracid orange GS and Direct fast turquoise blue GL) by the produced adsorbent was up to 97.6%. The activated carbon with pyrolusite addition had 38.2% higher surface area, 43.8% larger micropore and 54.4% larger mesopore production than ordinary sludge-based activated carbons. Equilibrium adsorption isotherms and kinetics were also investigated based on dyes adsorption tests. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption, and the results fitted well to the Langmuir isotherm. The kinetic data have been analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion equation. The experimental data fitted very well with pseudo-second-order kinetic model. Activation energies for the adsorption processes ranged between 8.7 and 19.1 kJ mol 1. Thermodynamic parameters such as standard free energy (deltaG0), standard enthalpy (deltaH0) and standard entropy (deltaS0) were evaluated. The adsorption of these two dyes on the activated carbon was found to be a spontaneous and endothermic process in nature. PMID:22097045

  2. Adsorption of methyl orange and salicylic acid on a nano-transition metal composite: Kinetics, thermodynamic and electrochemical studies.

    PubMed

    Arshadi, M; Mousavinia, F; Amiri, M J; Faraji, A R

    2016-12-01

    In this work synthesis of Mn-nanoparticles (MnNPs) supported on the Schiff base modified nano-sized SiO2Al2O3 mixed-oxides (Si/Al) and its implementation as an adsorbent for the removal of organic pollutions such as methyl orange (MO) and salicylic acid (SA) was investigated. Si/Al were functionalized by grafting Schiff base ligand and in the next step, MnNPs were prepared over the modified nano sol-gel Si/Al. Structures and adsorption characteristics of the obtained organometallic-modified SiO2/Al2O3 mixed oxide were studied by several methods such as elemental analysis, diffuse reflectance UV-vis spectroscopy, FT-IR spectroscopy, nitrogen adsorption/desorption, scanning electron microscope (SEM), transmission electron microscope (TEM), energy dispersive X-ray (EDX), inductively coupled plasma (ICP-AES), Electron Paramagnetic Resonance (EPR), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). EPR data of the immobilized manganese ions resulted that the transition state of active sites in the nano-adsorbent are in the form of Mn(II) ions at the surface. The adsorption properties of heterogeneous Mn(II) ions showed that this nano-adsorbent has very good potential to remove MO and SA ions from aqueous solution. The removal efficiency of the SAPAS@MnNPs towards MO reached out to 89.3 and 29.1% and for SA approached to 54.6 and 18.9% at 150 and 500mg/dm(3) initial organic pollution concentrations, respectively. To invest