Science.gov

Sample records for adsorption mtsa technology

  1. Investigation of Condensing Ice Heat Exchangers for MTSA Technology Development

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian; Powers, Aaron; Ball, Tyler; Lacomini, Christie; Paul, Heather L.

    2009-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal, carbon dioxide (CO2) and humidity control for a Portable Life Support Subsystem (PLSS). Metabolically-produced CO2 present in the ventilation gas of a PLSS is collected using a CO2-selective adsorbent via temperature swing adsorption. The temperature swing is initiated through cooling to well below metabolic temperatures. Cooling is achieved with a sublimation heat exchanger using water or liquid carbon dioxide (L CO2) expanded below sublimation temperature when exposed to low pressure or vacuum. Subsequent super heated vapor, as well as additional coolant, is used to further cool the astronaut. The temperature swing on the adsorbent is then completed by warming the adsorbent with a separate condensing ice heat exchanger (CIHX) using metabolic heat from moist ventilation gas. The condensed humidity in the ventilation gas is recycled at the habitat. The water condensation from the ventilation gas represents a significant source of potential energy for the warming of the adsorbent bed as it represents as much as half of the energy potential in the moist ventilation gas. Designing a heat exchanger to efficiently transfer this energy to the adsorbent bed and allow the collection of the water is a challenge since the CIHX will operate in a temperature range from 210K to 280K. The ventilation gas moisture will first freeze and then thaw, sometimes existing in three phases simultaneously.

  2. Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian A.; Powers, Aaron; Iacomini, Christie S.; Paul, Heather L.

    2011-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Ice Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously each the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU to the future flight unit are considered.

  3. Design and Assembly of an Integrated Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly Engineering Development Unit

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian A.; Powers, Aaron; Iacomini, Christie S.; Bower, Chad E.; Paul, Heather L.

    2012-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. The core of the MTSA technology is a sorbent bed that removes CO2 from the PLSS ventilation loop gas via a temperature swing. A Condensing Icing Heat eXchanger (CIHX) is used to warm the sorbent while also removing water from the ventilation loop gas. A Sublimation Heat eXchanger (SHX) is used to cool the sorbent. Research was performed to explore an MTSA designed for both lunar and Martian operations. Previously the sorbent bed, CIHX, and SHX had been built and tested individually on a scale relevant to PLSS operations, but they had not been done so as an integrated subassembly. Design and analysis of an integrated subassembly was performed based on this prior experience and an updated transient system model. Focus was on optimizing the design for Martian operations, but the design can also be used in lunar operations. An Engineering Development Unit (EDU) of an integrated MTSA subassembly was assembled based on the design. Its fabrication is discussed. Some details on the differences between the as-assembled EDU and the future flight unit are considered.

  4. Investigation of Condensing Ice Heat Exchangers for MTSA Technology Development

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian; Powers, Aaron; Ball, Tyler; Iacomini, Christie; Paul, Heather, L.

    2008-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal, carbon dioxide (CO2) and humidity control for a Portable Life Support Subsystem (PLSS). Metabolically-produced CO2 present in the ventilation gas of a PLSS is collected using a CO2selective adsorbent via temperature swing adsorption. The temperature swing is initiated through cooling to well below metabolic temperatures. Cooling is achieved with a sublimation heat exchanger using water or liquid carbon dioxide (LCO2) expanded below sublimation temperature when exposed to low pressure or vacuum. Subsequent super heated vapor, as well as additional coolant, is used to further cool the astronaut. The temperature swing on the adsorbent is then completed by warming the adsorbent with a separate condensing ice heat exchanger (CIHX) using metabolic heat from moist ventilation gas. The condensed humidity in the ventilation gas is recycled at the habitat. The water condensation from the ventilation gas is a significant heat transfer mechanism for the warming of the adsorbent bed because it represents as much as half of the energy potential in the moist ventilation gas. Designing a heat exchanger to efficiently transfer this energy to the adsorbent bed and allow the collection of the water is a challenge since the CIHX will operate in a temperature range from 210K to 280K. The ventilation gas moisture will first freeze and then thaw, sometimes existing in three phases simultaneously. A NASA Small Business Innovative Research (SBIR) Phase 1 contract was performed to investigate condensing and icing as applied to MTSA to enable higher fidelity modeling and assess the impact of geometry variables on CIHX performance for future CIHX design optimization. Specifically, a design tool was created using analytical relations to explore the complex, interdependent design space of a condensing ice heat exchanger. Numerous variables were identified as having nontrivial contributions

  5. System Modeling of Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly for Prototype Design

    NASA Technical Reports Server (NTRS)

    Bower, Chad; Padilla, Sebastian; Iacomini, Christie; Paul, Heather L.

    2009-01-01

    This paper describes modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly: the sorbent bed, a sublimation (cooling) heat exchanger (SHX), and a condensing icing (warming) heat exchanger (CIHX). The primary function of the MTSA, removing carbon dioxide from a ventilation loop, is performed via the sorbent bed. The CIHX is used to heat the sorbent bed for desorption and to remove moisture from the ventilation loop while the SHX is alternately employed to cool the sorbent bed via sublimation of a spray of water at low pressure to prepare the reconditioned bed for the next cycle. This paper describes a system level model of the MTSA as developed in Thermal Desktop and SINDA/FLUINT including assumptions on geometry and physical phenomena, modeling methodology and relevant pa ra mete rizatio ns. Several areas of particular modeling interest are discussed. In the sorbent bed, capture of the translating CO2 saturation front and associated local energy and mass balance in both adsorbing and desorbing modes is covered. The CIHX poses particular challenges for modeling in SINDA/FLUINT as accounting for solids states in fluid submodels are not a native capability. Methods for capturing phase change and latent heat of ice as well as the transport properties across a layer of low density accreted frost are developed. This extended modeling capacity is applicable to temperatures greater than 258 K. To extend applicability to the minimum device temperature of 235 K, a method for a mapped transformation of temperatures from below the limit temperatures to some value above is given along with descriptions for associated material property transformations and the resulting impacts to total heat and mass transfer. Similar considerations are shown for the SHX along with assumptions for flow mechanics and resulting model methods for sublimation in a flow.

  6. Modeling Of Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly For Prototype Design

    NASA Technical Reports Server (NTRS)

    Bower, Chad E.; Padilla, Sebastian A.; Iacomini, Christie S.; Paul, Heather L.

    2010-01-01

    This paper describes modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly: a sorbent bed, a sublimation (cooling) heat exchanger (SHX), and a condensing icing (warming) heat exchanger (CIHX). The primary function of the MTSA, removing carbon dioxide from a space suit Portable Life Support System (PLSS) ventilation loop, is performed via the sorbent bed. The CIHX is used to heat the sorbent bed for desorption and to remove moisture from the ventilation loop while the SHX is alternately employed to cool the sorbent bed via sublimation of a spray of water at low pressure to prepare the reconditioned bed for the next cycle. This paper describes subsystem heat a mass transfer modeling methodologies relevant to the description of the MTSA subassembly in Thermal Desktop and SINDA/FLUINT. Several areas of particular modeling interest are discussed. In the sorbent bed, capture of the translating carbon dioxide (CO2) front and associated local energy and mass balance in both adsorbing and desorbing modes is covered. The CIHX poses particular challenges for modeling in SINDA/FLUINT as accounting for solids states in fluid submodels are not a native capability. Methods for capturing phase change and latent heat of ice as well as the transport properties across a layer of low density accreted frost are developed. This extended modeling capacity is applicable to temperatures greater than 258 K. To extend applicability to the minimum device temperature of 235 K, a method for a mapped transformation of temperatures from below the limit temperatures to some value above is given along with descriptions for associated material property transformations and the resulting impacts to total heat and mass transfer. Similar considerations are given for the SHX along with functional relationships for areal sublimation rates as limited by flow mechanics in t1he outlet duct.

  7. Transient Modeling and Analysis of a Metabolic Heat-Regenerated Temperature Swing Adsorption (MTSA) System for a PLSS

    NASA Technical Reports Server (NTRS)

    Iacomini, Christie; Powers, Aaron; Speight, Garland; Padilla, Sebastian; Paul, Heather L.

    2009-01-01

    A Metabolic heat-regenerated Temperature Swing Adsorption (MTSA) system is being developed for carbon dioxide, water and thermal control in a lunar and martian portable life support system (PLSS). A previous system analysis was performed to evaluate the impact of MTSA on PLSS design. That effort was Mars specific and assumed liquid carbon dioxide (LCO2) coolant made from martian resources. Transient effects were not considered but rather average conditions were used throughout the analysis. This effort takes into further consideration the transient effects inherent in the cycling MTSA system as well as assesses the use of water as coolant. Standard heat transfer, thermodynamic, and heat exchanger methods are presented to conduct the analysis. Assumptions and model verification are discussed. The tool was used to perform various system studies. Coolant selection was explored and takes into account different operational scenarios as the minimum bed temperature is driven by the sublimation temperature of the coolant (water being significantly higher than LCO2). From this, coolant mass is sized coupled with sorbent bed mass because MTSA adsorption performance decreases with increasing sublimation temperature. Reduction in heat exchanger performance and even removal of certain heat exchangers, like a recuperative one between the two sorbent beds, is also investigated. Finally, the coolant flow rate is varied over the cycle to determine if there is a more optimal means of cooling the bed from a mass perspective. Results of these studies and subsequent recommendations for system design are presented.

  8. Simulated Lunar Testing of Metabolic Heat Regenerated Temperature Swing Adsorption Technology

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian A.; Bower, Chad; Iacomini, Christie S.; Paul, H.

    2011-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. An Engineering Development Unit (EDU) of the MTSA subassembly was designed and assembled for optimized Martian operations, but also meets system requirements for lunar operations. For lunar operations the MTSA sorption cycle is driven via a vacuum swing between suit ventilation loop pressure and lunar vacuum. The focus of this effort is operations and testing in a simulated lunar environment. This environment was simulated in Paragon s EHF vacuum chamber. The objective of this testing was to evaluate the full cycle performance of the MTSA Subassembly EDU, and to assess CO2 loading and pressure drop of the wash coated aluminum reticulated foam sorbent bed. The lunar testing proved out the feasibility of pure vacuum swing operation, making MTSA a technology that can be tested and used on the Moon prior to going to Mars. Testing demonstrated better than expected CO2 loading on the sorbent and nearly replicates the equilibrium data from the sorbent manufacturer. This had not been achieved in any of the previous sorbent loading tests performed by Paragon. Subsequently, the increased performance of the sorbent bed design indicates future designs will require less mass and volume than the current EDU rendering MTSA as very competitive for Martian PLSS applications.

  9. Simulated Lunar Testing of Metabolic Heat Regenerated Temperature Swing Adsorption

    NASA Technical Reports Server (NTRS)

    Padilla, Sebastian A.; Bower, Chad E.; Iacomini, Christie S.; Paul, Heather L.

    2012-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. An Engineering Development Unit (EDU) of the MTSA Subassembly (MTSAS) was designed and assembled for optimized Martian operations, but also meets system requirements for lunar operations. For lunar operations the MTSA sorption cycle is driven via a vacuum swing between suit ventilation loop pressure and lunar vacuum. The focus of this effort was testing in a simulated lunar environment. This environment was simulated in Paragon's EHF vacuum chamber. The objective of the testing was to evaluate the full cycle performance of the MTSA Subassembly EDU, and to assess CO2 loading and pressure drop of the wash coated aluminum reticulated foam sorbent bed. Lunar environment testing proved out the feasibility of pure vacuum swing operation, making MTSA a technology that can be tested and used on the Moon prior to going to Mars. Testing demonstrated better than expected CO2 Nomenclature loading on the sorbent and nearly replicates the equilibrium data from the sorbent manufacturer. This exceeded any of the previous sorbent loading tests performed by Paragon. Subsequently, the increased performance of the sorbent bed design indicates future designs will require less mass and volume than the current EDU rendering MTSA as very competitive for Martian PLSS applications.

  10. Investigating Liquid CO2 as a Coolant for a MTSA Heat Exchanger Design

    NASA Technical Reports Server (NTRS)

    Paul, Heather L.; Padilla, Sebastian; Powers, Aaron; Iacomini, Christie

    2009-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO 2) control for a future Portable Life Support System (PLSS), as well as water recycling. CO 2 removal and rejection is accomplished by driving a sorbent through a temperature swing of approximately 210 K to 280 K . The sorbent is cooled to these sub-freezing temperatures by a Sublimating Heat Exchanger (SHX) with liquid coolant expanded to sublimation temperatures. Water is the baseline coolant available on the moon, and if used, provides a competitive solution to the current baseline PLSS schematic. Liquid CO2 (LCO2) is another non-cryogenic coolant readily available from Martian resources which can be produced and stored using relatively low power and minimal infrastructure. LCO 2 expands from high pressure liquid (5800 kPa) to Mars ambient (0.8 kPa) to produce a gas / solid mixture at temperatures as low as 156 K. Analysis and experimental work are presented to investigate factors that drive the design of a heat exchanger to effectively use this sink. Emphasis is given to enabling efficient use of the CO 2 cooling potential and mitigation of heat exchanger clogging due to solid formation. Minimizing mass and size as well as coolant delivery are also considered. The analysis and experimental work is specifically performed in an MTSA-like application to enable higher fidelity modeling for future optimization of a SHX design. In doing so, the work also demonstrates principles and concepts so that the design can be further optimized later in integrated applications (including Lunar application where water might be a choice of coolant).

  11. Demonstration of Metabolic Heat Regenerated Temperature Swing Adsorption Technology

    NASA Technical Reports Server (NTRS)

    Paul, Heather; Iacomini, Christine; Powers, Aaron; Dunham, Jonah; Straub-Lopez, Katie; Anerson, Grant; MacCallum, Taber

    2007-01-01

    Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is currently being investigated for removal and rejection of CO2 and heat from a Portable Life Support System (PLSS) to a Martian environment. The metabolically-produced CO2 present in the vent loop gas is collected using a CO2 selective adsorbent that has been cooled via a heat exchanger to near CO2 sublimation temperatures (approx.195K) with liquid CO2 obtained from Martian resources. Once the adsorbent is fully loaded, fresh warm, moist vent loop (approx.300K) is used to heat the adsorbent via another heat exchanger. The adsorbent will then reject the collected CO2 to the Martian ambient. Two beds are used to achieve continuous CO2 removal by cycling between the cold and warm conditions for adsorbent loading and regeneration, respectively. Small experiments have already been completed to show that an adsorbent can be cycled between these PLSS operating conditions to provide adequate conditions for CO2 removal from a simulated vent loop. One of the remaining technical challenges is extracting enough heat from the vent loop to warm the adsorbent in an appreciable time frame to meet the required adsorb/desorb cycle. The other key technical aspect of the technology is employing liquid CO2 to achieve the appropriate cooling. A technology demonstrator has been designed, built and tested to investigate the feasibility of 1) warming the adsorbent using the moist vent loop, 2) cooling the adsorbent using liquid CO2, and 3) using these two methods in conjunction to successfully remove CO2 from a vent loop and reject it to Mars ambient. Both analytical and numerical methods were used to perform design calculations and trades. The demonstrator was built and tested. The design analysis and testing results are presented along with recommendations for future development required to increase the maturity of the technology.

  12. Testing, Modeling and System Impact of Metabolic Heat Regenerated Temperature Swing Adsorption

    NASA Technical Reports Server (NTRS)

    Lacomini, Christine S.; Powers, Aaron; Lewis, Matthew; Linrud, Christopher; Waguespack, Glenn; Conger, Bruce; Paul, Heather L.

    2008-01-01

    Metabolic heat regenerated temperature swing adsorption (MTSA) technology is being developed for removal and rejection of carbon dioxide (CO2) and heat from a portable life support system (PLSS) to the Martian environment. Previously, hardware was built and tested to demonstrate using heat from simulated, dry ventilation loop gas to affect the temperature swing required to regenerate an adsorbent used for CO2 removal. New testing has been performed using a moist, simulated ventilation loop gas to demonstrate the effects of water condensing and freezing in the heat exchanger during adsorbent regeneration. In addition, thermal models of the adsorbent during regeneration were modified and calibrated with test data to capture the effect of the CO2 heat of desorption. Finally, MTSA impact on PLSS design was evaluated by performing thermal balances assuming a specific PLSS architecture. Results using NASA s Extravehicular Activity System Sizing Analysis Tool (EVAS_SAT), a PLSS system evaluation tool, are presented.

  13. Sorbent, Sublimation, and Icing Modeling Methods: Experimental Validation and Application to an Integrated MTSA Subassembly Thermal Model

    NASA Technical Reports Server (NTRS)

    Bower, Chad; Padilla, Sebastian; Iacomini, Christie; Paul, Heather L.

    2010-01-01

    This paper details the validation of modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly, developed for use in a Portable Life Support System (PLSS). The first core component in the subassembly is a sorbent bed, used to capture and reject metabolically produced carbon dioxide (CO2). The sorbent bed performance can be augmented with a temperature swing driven by a liquid CO2 (LCO2) sublimation heat exchanger (SHX) for cooling the sorbent bed, and a condensing, icing heat exchanger (CIHX) for warming the sorbent bed. As part of the overall MTSA effort, scaled design validation test articles for each of these three components have been independently tested in laboratory conditions. Previously described modeling methodologies developed for implementation in Thermal Desktop and SINDA/FLUINT are reviewed and updated, their application in test article models outlined, and the results of those model correlations relayed. Assessment of the applicability of each modeling methodology to the challenge of simulating the response of the test articles and their extensibility to a full scale integrated subassembly model is given. The independent verified and validated modeling methods are applied to the development of a MTSA subassembly prototype model and predictions of the subassembly performance are given. These models and modeling methodologies capture simulation of several challenging and novel physical phenomena in the Thermal Desktop and SINDA/FLUINT software suite. Novel methodologies include CO2 adsorption front tracking and associated thermal response in the sorbent bed, heat transfer associated with sublimation of entrained solid CO2 in the SHX, and water mass transfer in the form of ice as low as 210 K in the CIHX.

  14. Metabolic Heat Regenerated Temperature Swing Adsorption for CO(sub 2) and Heat Removal/Rejection in a Martian PLSS

    NASA Technical Reports Server (NTRS)

    Iacomini, Christine; Powers, Aaron; Bowers, Chad; Straub-Lopez, Katie; Anderson, Grant; MacCallum, Taber; Paul, Heather

    2007-01-01

    Two of the fundamental problems facing the development of a Portable Life Support System (PLSS) for use on Mars, are (i) heat rejection (because traditional technologies use sublimation of water, which wastes a scarce resource and contaminates the premises), and (ii) rejection of CO2 in an environment with a ppCO2 of 0.4-0.9 kPa. Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed to address both these challenges. The technology utilizes an adsorbent that when cooled with liquid CO2 to near sublimation temperatures (195K) removes metabolically-produced CO2 in the vent loop. Once fully loaded, the adsorbent is then warmed externally by the vent loop (approx. 300K), rejecting the captured CO2 to Mars ambient. Two beds are used to effect a continuous cycle of CO2 removal/rejection as well as facilitate heat exchange out of the vent loop. Any cryogenic fluid can be used in the application; however, since CO2 is readily available at Mars and can be easily produced and stored on the Martian surface, the solution is rather elegant and less complicated when employing liquid CO2. As some metabolic heat will need to be rejected anyway, finding a practical use for metabolic heat is also an overall benefit to the PLSS. To investigate the feasibility of the technology, a series of experiments was conducted which lead to the selection and partial characterization of an appropriate adsorbent. The adsorbent NaX successfully removed CO2 from a simulated vent loop at the prescribed temperature swing anticipated during PLSS operating conditions on Mars using a cryogenic fluid. Thermal conductivity of the adsorbent was also measured to eventually aid in a demonstrator design of the technology. These results provide no show stoppers to the development of MTSA technology and allow its development to focus on other design challenges as listed in the conclusions.

  15. [Effects of ginkgo diterpene lactones meglumine injection's activated carbon adsorption technology on officinal components].

    PubMed

    Zhou, En-li; Wang, Ren-jie; Li, Miao; Wang, Wei; Xu, Dian-hong; Hu, Yang; Wang, Zhen-zhong; Bi, Yu-an; Xiao, Wei

    2015-10-01

    With the diversion rate of ginkgolide A, B, K as comprehensive evaluation indexes, the amount of activated carbon, ad- sorption time, mix rate, and adsorption temperature were selected as factors, orthogonal design which based on the evaluation method of information entropy was used to optimize activated carbon adsorption technology of ginkgo diterpene lactones meglumine injection. Opti- mized adsorption conditions were as follows: adsorbed 30 min with 0.2% activated carbon in 25 °C, 40 r ·min⁻¹, validation test re- sult display. The optimum extraction condition was stable and feasible, it will provide a basis for ginkgo diterpene lactone meglumine injection' activated carbon adsorption process.

  16. Martian Liquid CO2 and Metabolic Heat Regenerated Temperature Swing Adsorption for Portable Life Support Systems

    NASA Astrophysics Data System (ADS)

    Iacomini, Christine; MacCallum, Taber; Morin, Tom; Straub-Lopez, Kathrine; Paul, Heather

    2007-01-01

    Two of the fundamental problems facing the development of a Portable Life Support System (PLSS) for use on Mars, are (i) heat rejection (because traditional technologies use sublimation of water, which wastes a scarce resource and contaminates the premises), and (ii) rejection of CO2 in an environment with a ppCO2 of 0.4-0.9 kPa. This paper presents a conceptual system for CO2 collection, compression, and cooling to produce sub-critical (liquid) CO2. A first order estimate of the system mass and energy to condense and store liquid CO2 outside at Mars ambient temperature at 600 kPa is discussed. No serious technical hurdles were identified and it is likely that better overall performance would be achieved if the system were part of an integrated ISRU strategy rather than a standalone system. Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology for CO2 removal from a PLSS vent loop, where the Martian liquid CO2 is used as the heat sink is developed to utilize the readily available liquid CO2. This paper will describe the technology and present data in support of its design.

  17. Separation of soybean saponins from soybean meal by a technology of foam fractionation and resin adsorption.

    PubMed

    Jiang, Jianxing; Wu, Zhaoliang; Liu, Wei; Gao, Yanfei; Guo, Shenghao; Kang, Shufang

    2016-05-18

    Foam fractionation and resin adsorption were used to recover soybean saponins from the industrial residue of soybean meal. First, a two-stage foam fractionation technology was studied for concentrating soybean saponins from the leaching liquor. Subsequently, resin adsorption was used to purify soybean saponins from the foamate in foam fractionation. The results showed that the enrichment ratio, the recovery percentage, and the purity of soybean saponins by using the two-stage foam fractionation technology could reach 4.45, 74%, and 67%, respectively. After resin adsorption and desorption, the purity of soybean saponins in the freeze-dried powder from the desorption solution was 88.4%.

  18. Metabolic Heat Regenerated Temperature Swing Adsorption for CO2 and Heat Removal/Rejection in a Martian PLSS

    NASA Technical Reports Server (NTRS)

    Iacomini, Christine; Powers, Aaron; Bower, Chad; Straub-Lopez, Kathrine; Anderson, Grant; MacCallum, Taber; Paul, Heather L.

    2007-01-01

    Two of the fundamental problems facing the development of a Portable Life Support System (PLSS) for use on Mars, are (i) heat rejection (because traditional technologies use sublimation of water, which wastes a scarce resource and contaminates the premises), and (ii) rejection of carbon dioxide (CO2) in an environment with a CO2 partial pressure (ppCO2) of 0.4-0.9 kPa. Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed to address both these challenges. The technology utilizes an adsorbent that when cooled with liquid CO2 to near sublimation temperatures (195K) removes metabolically-produced CO2 in the ventilation loop. Once fully loaded, the adsorbent is then warmed externally by the ventilation loop (300K), rejecting the captured CO2 to Mars ambient. Two beds are used to provide a continuous cycle of CO2 removal/rejection as well as facilitate heat exchange out of the ventilation loop. Any cryogenic fluid can be used in the application; however, since CO2 is readily available on Mars and can be easily produced and stored on the Martian surface, the solution is rather elegant and less complicated when employing liquid CO2. As some metabolic heat will need to be rejected anyway, finding a practical use for metabolic heat is also an overall benefit to the PLSS. To investigate the feasibility of the technology, a series of experiments were conducted which lead to the selection and partial characterization of an appropriate adsorbent. The Molsiv Adsorbents 13X 8x12 (also known as NaX zeolite) successfully removed CO2 from a simulated ventilation loop at the prescribed temperature swing anticipated during PLSS operating conditions on Mars using a cryogenic fluid. Thermal conductivity of the adsorbent was also measured to eventually aid in a demonstrator design of the technology. These results provide no show stoppers to the development of MTSA technology and allow its development to focus on other design

  19. Surface modification of chitin using ultrasound-assisted and supercritical CO2 technologies for cobalt adsorption.

    PubMed

    Dotto, Guilherme L; Cunha, Jeanine M; Calgaro, Camila O; Tanabe, Eduardo H; Bertuol, Daniel A

    2015-09-15

    Ultrasound-assisted (UA) and supercritical CO2 technologies (SCO2) were used to modify the chitin surface and, improve its adsorption characteristics regarding to cobalt. Chitin, before and after the treatments, was characterized by N2 adsorption isotherms (BET), infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Unmodified and surface modified chitins were used as adsorbents to remove cobalt from aqueous solutions. The adsorption study was performed by equilibrium isotherms and kinetic curves. The chitin particle characteristics, such as, surface area, pore volume and porosity were improved by the UA and SCO2 treatments. The crystallinity index decreased after the UA and SCO2 treatments, and also, intense surface modifications were observed. Langmuir and Freundlich models were adequate to represent the adsorption equilibrium. The maximum adsorption capacities were 50.03, 83.94 and 63.08 mg g(-1) for unmodified chitin, UA surface modified chitin and SCO2 surface modified chitin. The adsorption kinetic curves were well represented by the pseudo-second order model. UA and SCO2 technologies are alternatives to modify the chitin surface and improve its adsorption characteristics.

  20. Investigation of Dynamic Oxygen Adsorption in Molten Solder Jetting Technology

    NASA Technical Reports Server (NTRS)

    Megaridis, Constantine M.; Bellizia, Giulio; McNallan, Michael; Wallace, David B.

    2003-01-01

    Surface tension forces play a critical role in fluid dynamic phenomena that are important in materials processing. The surface tension of liquid metals has been shown to be very susceptible to small amounts of adsorbed oxygen. Consequently, the kinetics of oxygen adsorption can influence the capillary breakup of liquid-metal jets targeted for use in electronics assembly applications, where low-melting-point metals (such as tin-containing solders) are utilized as an attachment material for mounting of electronic components to substrates. By interpreting values of surface tension measured at various surface ages, adsorption and diffusion rates of oxygen on the surface of the melt can be estimated. This research program investigates the adsorption kinetics of oxygen on the surface of an atomizing molten-metal jet. A novel oscillating capillary jet method has been developed for the measurement of dynamic surface tension of liquids, and in particular, metal melts which are susceptible to rapid surface degradation caused by oxygen adsorption. The experimental technique captures the evolution of jet swells and necks continuously along the jet propagation axis and is used in conjunction with an existing linear, axisymmetric, constant-property model to determine the variation of the instability growth rate, and, in turn, surface tension of the liquid as a function of surface age measured from the exit orifice. The conditions investigated so far focus on a time window of 2-4ms from the jet orifice. The surface properties of the eutectic 63%Sn-37%Pb solder alloy have been investigated in terms of their variation due to O2 adsorption from a N2 atmosphere containing controlled amounts of oxygen (from 8 ppm to 1000 ppm). The method performed well for situations where the oxygen adsorption was low in that time window. The value of surface tension for the 63Sn-37Pb solder in pure nitrogen was found to be 0.49 N/m, in good agreement with previously published work. A characteristic

  1. Emerging technologies in extracorporeal treatment: focus on adsorption.

    PubMed

    Mikhalovsky, Sergey V

    2003-03-01

    As an extracorporeal technique for blood purification, haemoadsorption was introduced in the early 1960s along with other physico-chemical methods. The problem of poor biocompatibility of uncoated adsorbents was resolved by coating adsorbent granules with haemocompatible membranes. Use of coated adsorbents instead of uncoated ones reduces the efficiency of haemoperfusion. As a result, for many years the use of adsorption was limited to only acute poisoning. Since the 1990s interest in the use of adsorbents in extracorporeal medical devices has been rising again. In this paper some recent developments in synthesis and application of novel uncoated medical adsorbents are discussed.

  2. Color removal from paper mill effluent through adsorption technology.

    PubMed

    Jain, C K; Kumar, Arvind; Hayssam Izazy, M

    2009-02-01

    The bagasse fly ash, obtained from the local sugar industry, has been used as an inexpensive and effective adsorbent for the removal of color from pulp and paper industry. Effect of various operating variables, viz., contact time, initial concentration, adsorbent dose and particle size on the removal of color has been studied and discussed. It is found that for optimum removal of color, contact time for adsorption equilibrium equals to 60 min., at dosage of 2 g/l of baggase fly ash. The material exhibits good removal capacity (86%) and follows both the Langmuir and the Freundlich models.

  3. [Use of fractional plasma separation and adsorption (Prometheus technology) in the treatment of acute liver failure].

    PubMed

    Denisova, E N; Sharipova, V R; Purlo, N V; Sukhanova, G A; Biriukova, L S

    2009-01-01

    This paper presents the results of treating 8 patients with acute liver failure, by using the separation and adsorption of fractional plasma (Prometheus technology). Twenty-five procedures lasting 5-6 hours were performed. Anticoagulation with heparin was made under guidance of coagulogram parameters. The results of testing blood parameters before and after a procedure and hemodynamic parameters are given. The investigations have demonstrated the effectiveness and safety of the procedure.

  4. Development of Pressure Swing Adsorption Technology for Spacesuit Carbon Dioxide and Humidity Removal

    NASA Technical Reports Server (NTRS)

    Papale, William; Paul, Heather; Thomas, Gretchen

    2006-01-01

    Metabolically produced carbon dioxide (CO2) removal in spacesuit applications has traditionally been accomplished utilizing non-regenerative Lithium Hydroxide (LiOH) canisters. In recent years, regenerative Metal Oxide (MetOx) has been developed to replace the Extravehicular Mobility Unity (EMU) LiOH canister for extravehicular activity (EVA) missions in micro-gravity, however, MetOx may carry a significant weight burden for potential use in future Lunar or planetary EVA exploration missions. Additionally, both of these methods of CO2 removal have a finite capacity sized for the particular mission profile. Metabolically produced water vapor removal in spacesuits has historically been accomplished by a condensing heat exchanger within the ventilation process loop of the suit life support system. Advancements in solid amine technology employed in a pressure swing adsorption system have led to the possibility of combining both the CO2 and humidity control requirements into a single, lightweight device. Because the pressure swing adsorption system is regenerated to space vacuum or by an inert purge stream, the duration of an EVA mission may be extended significantly over currently employed technologies, while markedly reducing the overall subsystem weight compared to the combined weight of the condensing heat exchanger and current regenerative CO2 removal technology. This paper will provide and overview of ongoing development efforts evaluating the subsystem size required to manage anticipated metabolic CO2 and water vapor generation rates in a spacesuit environment.

  5. In-situ Adsorption-Biological Combined Technology Treating Sediment Phosphorus in all Fractions

    PubMed Central

    Zhang, Y.; Wang, C.; He, F.; Liu, B.; Xu, D.; Xia, S.; Zhou, Q.; Wu, Z.

    2016-01-01

    The removal efficiency of sediment phosphorus (P) in all fractions with in-situ adsorption-biological combined technology was studied in West Lake, Hangzhou, China. The removal amounts of sediment Ca-P, Fe/Al-P, IP, OP and TP by the combined effect of PCFM (Porous ceramic filter media) and V. spiralis was 61 mg/kg, 249 mg/kg, 318 mg/kg, 85 mg/kg and 416 mg/kg, respectively, and the corresponding removing rate reached 10.5%, 44.6%, 27.5%, 30.6% and 29.2%. This study suggested that the combination of PCFM and V. spiralis could achieve a synergetic sediment P removal because the removal rates of the combinations were higher than the sum of that of PCFM and macrophytes used separately. From analysis of sediment microbial community and predicted function, we found that the combined PCFM and V. spiralis enhanced the function of P metabolism by increasing specific genus that belong to phylum Firmicutes and Nitrospirae. Thus it can be seen the in-situ adsorption-biological combined technology could be further applied to treat internal P loading in eutrophic waters. PMID:27418242

  6. In-situ Adsorption-Biological Combined Technology Treating Sediment Phosphorus in all Fractions

    NASA Astrophysics Data System (ADS)

    Zhang, Y.; Wang, C.; He, F.; Liu, B.; Xu, D.; Xia, S.; Zhou, Q.; Wu, Z.

    2016-07-01

    The removal efficiency of sediment phosphorus (P) in all fractions with in-situ adsorption-biological combined technology was studied in West Lake, Hangzhou, China. The removal amounts of sediment Ca-P, Fe/Al-P, IP, OP and TP by the combined effect of PCFM (Porous ceramic filter media) and V. spiralis was 61 mg/kg, 249 mg/kg, 318 mg/kg, 85 mg/kg and 416 mg/kg, respectively, and the corresponding removing rate reached 10.5%, 44.6%, 27.5%, 30.6% and 29.2%. This study suggested that the combination of PCFM and V. spiralis could achieve a synergetic sediment P removal because the removal rates of the combinations were higher than the sum of that of PCFM and macrophytes used separately. From analysis of sediment microbial community and predicted function, we found that the combined PCFM and V. spiralis enhanced the function of P metabolism by increasing specific genus that belong to phylum Firmicutes and Nitrospirae. Thus it can be seen the in-situ adsorption-biological combined technology could be further applied to treat internal P loading in eutrophic waters.

  7. Adsorbent Alkali Conditioning for Uranium Adsorption from Seawater. Adsorbent Performance and Technology Cost Evaluation

    SciTech Connect

    Tsouris, Costas; Mayes, Richard T.; Janke, Christopher James; Dai, Sheng; Das, S.; Liao, W. -P.; Kuo, Li-Jung; Wood, Jordana; Gill, Gary; Byers, Maggie Flicker; Schneider, Eric

    2015-09-30

    The Fuel Resources program of the Fuel Cycle Research and Development program of the Office of Nuclear Energy (NE) is focused on identifying and implementing actions to assure that nuclear fuel resources are available in the United States. An immense source of uranium is seawater, which contains an estimated amount of 4.5 billion tonnes of dissolved uranium. This unconventional resource can provide a price cap and ensure centuries of uranium supply for future nuclear energy production. NE initiated a multidisciplinary program with participants from national laboratories, universities, and research institutes to enable technical breakthroughs related to uranium recovery from seawater. The goal is to develop advanced adsorbents to reduce the seawater uranium recovery technology cost and uncertainties. Under this program, Oak Ridge National Laboratory (ORNL) has developed a new amidoxime-based adsorbent of high surface area, which tripled the uranium capacity of leading Japanese adsorbents. Parallel efforts have been focused on the optimization of the physicochemical and operating parameters used during the preparation of the adsorbent for deployment. A set of parameters that need to be optimized are related to the conditioning of the adsorbent with alkali solution, which is necessary prior to adsorbent deployment. Previous work indicated that alkali-conditioning parameters significantly affect the adsorbent performance. Initiated in 2014, this study had as a goal to determine optimal parameters such as base type and concentration, temperature, and duration of conditioning that maximize the uranium adsorption performance of amidoxime functionalized adsorbent, while keeping the cost of uranium production low. After base-treatment at various conditions, samples of adsorbent developed at ORNL were tested in this study with batch simulated seawater solution of 8-ppm uranium concentration, batch seawater spiked with uranium nitrate at 75-100 ppb uranium, and continuous

  8. CROSS-DISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Monomer Adsorption-Desorption Processes

    NASA Astrophysics Data System (ADS)

    Ke, Jian-Hong; Lin, Zhen-Quan; Chen, Xiao-Shuang

    2009-05-01

    We propose an adsorption-desorption model for a deposit growth system, in which the adsorption and desorption of particles coexist. By means of the generalized rate equation we investigate the cluster (island) size distribution in the dynamic equilibrium state. The results show that the evolution behaviour of the system depends crucially on the details of the rate kernels. The cluster size distribution can take the scale-free power-law form in some cases, while it grows exponentially with size in other cases.

  9. Treatment of landfill leachate using ASBR combined with zeolite adsorption technology.

    PubMed

    Lim, Chi Kim; Seow, Ta Wee; Neoh, Chin Hong; Md Nor, Muhamad Hanif; Ibrahim, Zaharah; Ware, Ismail; Mat Sarip, Siti Hajar

    2016-12-01

    Sanitary landfilling is the most common way to dispose solid urban waste; however, improper landfill management may pose serious environmental threats through discharge of high strength polluted wastewater also known as leachate. The treatment of landfill leachate to fully reduce the negative impact on the environment, is nowadays a challenge. In this study, an aerobic sequencing batch reactor (ASBR) was proposed for the treatment of locally obtained real landfill leachate with initial ammoniacal nitrogen and chemical oxygen demand (COD) concentration of 1800 and 3200 mg/L, respectively. ASBR could remove 65 % of ammoniacal nitrogen and 30 % of COD during seven days of treatment time. Thereafter, an effective adsorbent, i.e., zeolite was used as a secondary treatment step for polishing the ammoniacal nitrogen and COD content that is present in leachate. The results obtained are promising where the adsorption of leachate by zeolite further enhanced the removal of ammoniacal nitrogen and COD up to 96 and 43 %, respectively. Furthermore, this combined biological-physical treatment system was able to remove heavy metals, i.e. aluminium, vanadium, chromium, magnesium, cuprum and plumbum significantly. These results demonstrate that combined ASBR and zeolite adsorption is a feasible technique for the treatment of landfill leachate, even considering this effluent's high resistance to treatment.

  10. Characterization by optical measurements of the effects of some stages of champagne technology on the adsorption layer formed at the gas/wine interface.

    PubMed

    Saleh, K Abou; Aguié-Béghin, V; Foulon, L; Valade, M; Douillard, R

    2007-06-19

    This study analyzes the effects of some important factors of champagne technology on the ellipticity and Brewster angle microscopy (BAM) of the air/champagne interface in view of using the optical properties of the adsorption layer of base wine to forecast the stability of the champagne bubble collar. Using standard, ultrafiltered, and ultraconcentrated wines it was observed that champagne can lose amphiphilic macromolecules which adsorb on the inner glass wall of the bottle during storage, particles such as dead yeasts can adhere to the adsorption layer, a weak increase of the ethanol content during bottle fermentation can reduce significantly the ellipticity of the adsorption layer, and CO2 has no significant effect on the properties of that layer. Surprisingly, no visible differences of the adsorption layer were noticed between the experimental champagnes of the 2004 vintage of three vine varieties (Chardonnay, Pinot noir, and Pinot meunier). From analysis of all samples it is proposed that the mean value and standard deviation of the ellipticity measured during 30 min after pouring the wine in a Petri dish are physical quantities which satisfactorily characterize the adsorption layer of champagne. When needed, further characterization of the adsorption layer may be obtained by a detailed analysis of the kinetics of ellipticity during the same period and inspection of the BAM images of the interface.

  11. Adsorption Refrigeration System

    SciTech Connect

    Wang, Kai; Vineyard, Edward Allan

    2011-01-01

    Adsorption refrigeration is an environmentally friendly cooling technology which could be driven by recovered waste heat or low-grade heat such as solar energy. In comparison with absorption system, an adsorption system has no problems such as corrosion at high temperature and salt crystallization. In comparison with vapor compression refrigeration system, it has the advantages of simple control, no moving parts and less noise. This paper introduces the basic theory of adsorption cycle as well as the advanced adsorption cycles such as heat and mass recovery cycle, thermal wave cycle and convection thermal wave cycle. The types, characteristics, advantages and drawbacks of different adsorbents used in adsorption refrigeration systems are also summarized. This article will increase the awareness of this emerging cooling technology among the HVAC engineers and help them select appropriate adsorption systems in energy-efficient building design.

  12. Final Report - Development of New Pressure Swing Adsorption (PSA) Technology to Recover High Valued Products from Chemical Plant and Refinery Waste Systems

    SciTech Connect

    Keith Ludwig

    2004-06-14

    Project Objective was to extend pressure swing adsorption (PSA) technology into previously under-exploited applications such as polyolefin production vent gas recovery and H2 recovery from refinery waste gases containing significant amounts of heavy hydrocarbons, aromatics, or H2S.

  13. Adsorption modeling for macroscopic contaminant dispersal analysis

    SciTech Connect

    Axley, J.W.

    1990-05-01

    Two families of macroscopic adsorption models are formulated, based on fundamental principles of adsorption science and technology, that may be used for macroscopic (such as whole-building) contaminant dispersal analysis. The first family of adsorption models - the Equilibrium Adsorption (EA) Models - are based upon the simple requirement of equilibrium between adsorbent and room air. The second family - the Boundary Layer Diffusion Controlled Adsorption (BLDC) Models - add to the equilibrium requirement a boundary layer model for diffusion of the adsorbate from the room air to the adsorbent surface. Two members of each of these families are explicitly discussed, one based on the linear adsorption isotherm model and the other on the Langmuir model. The linear variants of each family are applied to model the adsorption dynamics of formaldehyde in gypsum wall board and compared to measured data.

  14. A biological oil adsorption filter.

    PubMed

    Pasila, Antti

    2004-12-01

    A new oil adsorption method called adsorption filtration (AF) has been developed. It is a technology where by oil residues can be cleaned from water by running it through a simple filter made from freeze treated, dried, milled and then fragmented plant material. By choosing suitable plants and fragmentation sizes it is possible to produce filters, which pass water but adsorb oil. The aim of this study was to investigate the possibilities of manufacturing oil adsorbing filter materials from reed canary grass (Phalaris arundinacea), flax (Linum usitatissimum L.) or hemp fibre (Cannabis sativa L.). The oil (80 ml) was mixed with de-ionised water (200 ml) and this mixture was filtered through 10 or 20 g adsorption filters. Fine spring harvested hemp fibre (diameter less than 1 mm) and reed canary grass fragments adsorb 2-4 g of oil per gram of adsorption material compared to 1-3 g of water. Adsorption filtration is thus a novel way of gathering spilled oil in shallow coastal waters before the oil reaches the shore.

  15. Adsorption characteristics, recognition properties, and preliminary application of nordihydroguaiaretic acid molecularly imprinted polymers prepared by sol-gel surface imprinting technology

    NASA Astrophysics Data System (ADS)

    Liao, Sen; Zhang, Wen; Long, Wei; Hou, Dan; Yang, Xuechun; Tan, Ni

    2016-02-01

    In this paper, a new core-shell composite of nordihydroguaiaretic acid (NDGA) molecularly imprinted polymers layer-coated silica gel (MIP@SiO2) was prepared through sol-gel technique and applied as a material for extraction of NDGA from Ephedra. It was synthesized using NDGA as the template molecule, γ-aminopropyltriethoxysilane (APTS) and methyltriethoxysilane (MTEOS) as the functional monomers, tetraethyl orthosilicate (TEOS) as the cross-linker and ethanol as the porogenic solvent in the surface of silica. The non-imprinted polymers layer-coated silica gel (NIP@SiO2) were prepared with the same procedure, but with the absence of template molecule. In addition, the optimum adsorption affinity occurred when the molar ratio of NDGA:APTS:MTEOS:TEOS was 1:6:2:80. The prepared MIP@SiO2 and NIP@SiO2 were analyzed by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Fourier transform-infrared spectroscopy (FT-IR). Their affinity properties to NDGA were evaluated through dynamic adsorption, static adsorption, and selective recognition experiments, and the results showed the saturated adsorption capacity of MIP@SiO2 could reach to 5.90 mg g-1, which was two times more than that of NIP@SiO2. High performance liquid chromatography (HPLC) was used to evaluate the extraction of NDGA from the medicinal plant ephedra by the above prepared materials, and the results indicated that the MIP@SiO2 had potential application in separation of the natural active component NDGA from medicinal plants.

  16. Cation siting in low-silica zeolites with potential applications in pressure swing adsorption technology and structural studies of novel tectosilicates

    NASA Astrophysics Data System (ADS)

    Burton, Allen Wayne

    Adsorption and catalytic phenomena in zeolites are influenced by coulombic interactions within zeolite structure as well as by size restrictions imposed by zeolitic micropores. In the first part of this thesis, we investigate materials with potential applications in the selective adsorption of nitrogen. Studies have indicated the performance of LiX adsorbents correlates with the number of accessible lithium cations in the zeolite. However, in zeolite LiX only one-third of the lithium cations interact with adsorbed molecules. This prompted our investigation of other low-silica zeolites. The first zeolite examined was a cancrinite prepared in the presence of 1,3-butanediol. Neutron diffraction studies on the lithium-exchanged cancrinite suggest most of the lithium cations are ideally positioned within the micropores. However, our experiments show that carbonate anions are occluded within the micropores of this cancrinite. Another material examined in this study was zeolite (Ba,K)-GL. Neutron diffraction experiments show that 49 of the extraframework charges are located in the micropores. Unfortunately, less than 20% of these cations are replaced after lithium-exchange. We also attempted to directly synthesize a (Ba,Li)-GL. However, diffraction experiments and chemical analyses show that most of the extraframework charge is compensated by barium. Because of molecular size restrictions imposed by currently known zeolites, there is continued interest in the synthesis of materials that can be used for processing large molecules. This motivated our investigation of two tectosilicates MCM-61 and MCM-47. MCM-61 is an aluminosilicate made in the presence of the potassium-18-Crown-6 complex. Our structure solution shows MCM-61 is formed from novel [610412] polyhedral cage units that connect to form 18-membered-ring cages. The structure of MCM-61 suggests that crown ethers, azamacrocycles, and cryptands may be useful for the syntheses of extra-large pore zeolites. MCM-47 is

  17. A Simple Adsorption Experiment

    ERIC Educational Resources Information Center

    Guirado, Gonzalo; Ayllon, Jose A.

    2011-01-01

    The study of adsorption phenomenon is one of the most relevant and traditional physical chemistry experiments performed by chemistry undergraduate students in laboratory courses. In this article, we describe an easy, inexpensive, and straightforward way to experimentally determine adsorption isotherms using pieces of filter paper as the adsorbent…

  18. Temperature Swing Adsorption Compressor Development

    NASA Technical Reports Server (NTRS)

    Finn, John E.; Mulloth, Lila M.; Affleck, Dave L.

    2001-01-01

    Closing the oxygen loop in an air revitalization system based on four-bed molecular sieve and Sabatier reactor technology requires a vacuum pump-compressor that can take the low-pressure CO, from the 4BMS and compress and store for use by a Sabatier reactor. NASA Ames Research Center proposed a solid-state temperature-swing adsorption (TSA) compressor that appears to meet performance requirements, be quiet and reliable, and consume less power than a comparable mechanical compressor/accumulator combination. Under this task, TSA compressor technology is being advanced through development of a complete prototype system. A liquid-cooled TSA compressor has been partially tested, and the rest of the system is being fabricated. An air-cooled TSA compressor is also being designed.

  19. Hybrid adsorptive membrane reactor

    NASA Technical Reports Server (NTRS)

    Tsotsis, Theodore T. (Inventor); Sahimi, Muhammad (Inventor); Fayyaz-Najafi, Babak (Inventor); Harale, Aadesh (Inventor); Park, Byoung-Gi (Inventor); Liu, Paul K. T. (Inventor)

    2011-01-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  20. Generalized random sequential adsorption

    NASA Astrophysics Data System (ADS)

    Tarjus, G.; Schaaf, P.; Talbot, J.

    1990-12-01

    Adsorption of hard spherical particles onto a flat uniform surface is analyzed by using generalized random sequential adsorption (RSA) models. These models are defined by releasing the condition of immobility present in the usual RSA rules to allow for desorption or surface diffusion. Contrary to the simple RSA case, generalized RSA processes are no longer irreversible and the system formed by the adsorbed particles on the surface may reach an equilibrium state. We show by using a distribution function approach that the kinetics of such processes can be described by means of an exact infinite hierarchy of equations reminiscent of the Kirkwood-Salsburg hierarchy for systems at equilibrium. We illustrate the way in which the systems produced by adsorption/desorption and by adsorption/diffusion evolve between the two limits represented by ``simple RSA'' and ``equilibrium'' by considering approximate solutions in terms of truncated density expansions.

  1. Hybrid adsorptive membrane reactor

    SciTech Connect

    Tsotsis, Theodore T.; Sahimi, Muhammad; Fayyaz-Najafi, Babak; Harale, Aadesh; Park, Byoung-Gi; Liu, Paul K. T.

    2011-03-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  2. Assessing the Adsorption Properties of Shales

    NASA Astrophysics Data System (ADS)

    Pini, R.

    2014-12-01

    Fine-grained rocks, such as shales, contain a significant amount of nanopores that can significantly contribute to their storage capacity through the mechanism of adsorption. The current ability to extract natural gas that is adsorbed in the rock's matrix is limited and current technology focuses primarily on the free gas in the fractures, thus leading to very low recovery efficiencies. Shales constitute also a great portion of so-called caprocks above potential CO2 sequestration sites; hereby, the adsorption process may limit the CO2 mobility within the cap-rock, thus minimizing leakage phenomena. Whether it is a reservoir or a caprock, understanding and quantifying the mechanisms of adsorption in these natural materials is key to improve the engineering design of subsurface operations. Results will be presented from a laboratory study that combines conventional techniques for the measurement of adsorption isotherms with novel methods that allows for the imaging of adsorption using x-rays. Various nanoporous materials are considered, thus including rocks, such as shales and coals, pure clay minerals and engineered adsorbents with well-defined nanopore structures, such as zeolites. Supercritical CO2 adsorption isotherms have been measured with a Rubotherm Magnetic Suspension balance by covering the pressure range 0.1-20~MPa. A medical x-ray CT scanner has been used to identify three-dimensional patterns of the adsorption properties of a packed-bed of adsorbent, thus enabling to assess the spatial variability of the adsorption isotherm. The data are analyzed by using thermodynamically rigorous measures of adsorption and a graphical method is applied for their interpretation. The density of the adsorbed phase is estimated and compared to data reported in the literature; the latter is key to disclose gas-reserves and/or potential storage capacity estimates. When evaluated against classic adsorbent materials, the adsorption mechanism in shales is further complicated by

  3. Modeling adsorption: Investigating adsorbate and adsorbent properties

    NASA Astrophysics Data System (ADS)

    Webster, Charles Edwin

    1999-12-01

    Surface catalyzed reactions play a major role in current chemical production technology. Currently, 90% of all chemicals are produced by heterogeneously catalyzed reactions. Most of these catalyzed reactions involve adsorption, concentrating the substrate(s) (the adsorbate) on the surface of the solid (the adsorbent). Pore volumes, accessible surface areas, and the thermodynamics of adsorption are essential in the understanding of solid surface characteristics fundamental to catalyst and adsorbent screening and selection. Molecular properties such as molecular volumes and projected molecular areas are needed in order to convert moles adsorbed to surface volumes and areas. Generally, these molecular properties have been estimated from bulk properties, but many assumptions are required. As a result, different literature values are employed for these essential molecular properties. Calculated molar volumes and excluded molecular areas are determined and tabulated for a variety of molecules. Molecular dimensions of molecules are important in the understanding of molecular exclusion as well as size and shape selectivity, diffusion, and adsorbent selection. Molecular dimensions can also be used in the determination of the effective catalytic pore size of a catalyst. Adsorption isotherms, on zeolites, (crystalline mineral oxides) and amorphous solids, can be analyzed with the Multiple Equilibrium Analysis (MEA) description of adsorption. The MEA produces equilibrium constants (Ki), capacities (ni), and thermodynamic parameters (enthalpies, ΔHi, and entropies, ΔSi) of adsorption for each process. Pore volumes and accessible surface areas are calculated from the process capacities. Adsorption isotherms can also be predicted for existing and new adsorbate-adsorbent systems with the MEA. The results show that MEA has the potential of becoming a standard characterization method for microporous solids that will lead to an increased understanding of their behavior in gas

  4. Technology

    ERIC Educational Resources Information Center

    Isman, Aytekin

    2003-01-01

    This article begins by drawing on literature to examine the various definitions of "technology" and "technique." Following a discussion of the origin of technology in education, the remaining sections of the article focus on the relationships and interaction between: (1) machines and technique; (2) science and technique; (3)…

  5. Technology.

    ERIC Educational Resources Information Center

    Giorgis, Cyndi; Johnson, Nancy J.

    2002-01-01

    Presents annotations of 30 works of children's literature that support the topic of technology and its influences on readers' daily lives. Notes some stories tell about a time when simple tools enabled individuals to accomplish tasks, and others feature visionaries who used technology to create buildings, bridges, roads, and inventions. Considers…

  6. Adsorption of star polymers

    NASA Astrophysics Data System (ADS)

    Halperin, A.; Joanny, J. F.

    1991-06-01

    The adsorption of star polymers on a flat solid surface is analyzed by means of scalling arguments based on the Daoud-Cotton blob model. For the adsorption of a single star, consisting of f arms comprising each N monomers, we distinguish three regimes determined by the adsorption energy of a monomer at the surface, δ kT. 1) Strong adsorption characterized by the full adsorption of all arms occurs for δ > (f/N)^{3/5}. 2) A “Sombrero” like structure comprising f_ads fully adsorbed arms and f{-}f_ads free arms is obtained for (f/N)^{3/5}> δ > f^{9/20}/N^{3/5}. 3) Weakly adsorbed stars retain, essentially, the structure of a free star. This regime occurs for δ < f^{9/20}/N^{3/5}. The weakly adsorbed structure may also exist as a metastable state if δ > f^{9/5}/N^{3/5}. Nous étudions l'adsorption de polymères en étoile sur une surface solide en utilisant une approche de lois d'échelles basée sur le modèle de blobs de Daoud et Cotton. Pour une étoile formée de f bras contenant chacun N monomères, nous distinguons trois régimes suivant la valeur de l'énergie d'adsorption d'un monomère sur la surface δ kT. 1) L'adsorption forte caractérisée par une adsorption complète de tous les bras se produit lorsque δ > (f/N)^{3/5}. 2) Une structure en “sombrero” avec f_ads bras adsorbés et f{-}f_ads bras libres est obtenue si f^{9/20}/N^{3/5}δ < (f/N)^{3/5}. 3) Les étoiles faiblement adsorbées gardent une structure très similaire à celle des étoiles libres en solution. Ce régime existe si δ < f^{9/20}/N^{3/5}. La structure correspondant aux étoiles faiblement adsorbées peut aussi exister comme un état métastable si δ > f^{9/5}/N^{3/5}.

  7. Preparation and properties of ion-imprinted hollow particles for the selective adsorption of silver ions.

    PubMed

    Hou, Hongbin; Yu, Demei; Hu, Guohe

    2015-02-03

    Four kinds of silver ion-imprinted particles (Ag-IIPs) with different morphologies were prepared by the surface ion-imprinting technology (SIIT) and were used for the selective removal and concentration of silver ions from wastewater. The favorable adsorptivity and selectivity of Ag-IIPs for Ag(+) were confirmed by a series of adsorption experiments at a suitable pH value. The adsorption mechanism was elucidated by analyzing the adsorption isotherms, adsorption thermodynamics, and adsorption kinetics systematically. The Ag(+) adsorption onto the Ag-IIPs was well-described by the Langmuir isotherm model, and it was likely to be a monolayer chemical adsorption. This conclusion was also confirmed by the thermodynamic parameters. Moreover, the adsorption kinetics indicated that the adsorption rate would be controlled jointly by the intraparticle diffusion and the inner surface adsorption process, and the latter process was generally associated with the formation and breaking of chemical bonds. Finally, the effects of different morphologies of the Ag-IIPs for Ag(+) adsorption were also investigated. In aqueous solution, the adsorptivity of the Ag(+) ion-imprinting single-hole hollow particles (Ag-IISHPs) for Ag(+) was highest (80.5 mg g(-1)) because of a specific morphology that features a single hole in the shell. In an oil-water mixture, Ag(+) in the water phase could be adsorbed efficiently by the Ag(+) ion-imprinting Janus hollow particles (Ag-IIJHPs), with emulsifiability originating from the Janus structure.

  8. Removal of mercury by adsorption: a review.

    PubMed

    Yu, Jin-Gang; Yue, Bao-Yu; Wu, Xiong-Wei; Liu, Qi; Jiao, Fei-Peng; Jiang, Xin-Yu; Chen, Xiao-Qing

    2016-03-01

    Due to natural and production activities, mercury contamination has become one of the major environmental problems over the world. Mercury contamination is a serious threat to human health. Among the existing technologies available for mercury pollution control, the adsorption process can get excellent separation effects and has been further studied. This review is attempted to cover a wide range of adsorbents that were developed for the removal of mercury from the year 2011. Various adsorbents, including the latest adsorbents, are presented along with highlighting and discussing the key advancements on their preparation, modification technologies, and strategies. By comparing their adsorption capacities, it is evident from the literature survey that some adsorbents have shown excellent potential for the removal of mercury. However, there is still a need to develop novel, efficient adsorbents with low cost, high stability, and easy production and manufacture for practical utility.

  9. Technology.

    ERIC Educational Resources Information Center

    Online-Offline, 1998

    1998-01-01

    Focuses on technology, on advances in such areas as aeronautics, electronics, physics, the space sciences, as well as computers and the attendant progress in medicine, robotics, and artificial intelligence. Describes educational resources for elementary and middle school students, including Web sites, CD-ROMs and software, videotapes, books,…

  10. New Adsorption Methods.

    ERIC Educational Resources Information Center

    Wankat, Phillip C.

    1984-01-01

    Discusses a simple method for following the movement of a solute in an adsorption or ion exchange system. This movement is used to study a variety of operational methods, including continuous flow and pulsed flow counter-current operations and simulated counter-current systems. Effect of changing thermodynamic variables is also considered. (JM)

  11. SEPARATION BY ADSORPTION

    DOEpatents

    Lowe, C.S.

    1959-06-16

    Separation of Pu from fission products by adsorption on hydrous aluminum silicate is described. The Pu in a HNO/sub 3/ solution is oxidized to the hexavalent state and contacted with the silicate which adsorbs fission products. (T.R.H.)

  12. A pressure-amplifying framework material with negative gas adsorption transitions.

    PubMed

    Krause, Simon; Bon, Volodymyr; Senkovska, Irena; Stoeck, Ulrich; Wallacher, Dirk; Többens, Daniel M; Zander, Stefan; Pillai, Renjith S; Maurin, Guillaume; Coudert, François-Xavier; Kaskel, Stefan

    2016-04-21

    Adsorption-based phenomena are important in gas separations, such as the treatment of greenhouse-gas and toxic-gas pollutants, and in water-adsorption-based heat pumps for solar cooling systems. The ability to tune the pore size, shape and functionality of crystalline porous coordination polymers--or metal-organic frameworks (MOFs)--has made them attractive materials for such adsorption-based applications. The flexibility and guest-molecule-dependent response of MOFs give rise to unexpected and often desirable adsorption phenomena. Common to all isothermal gas adsorption phenomena, however, is increased gas uptake with increased pressure. Here we report adsorption transitions in the isotherms of a MOF (DUT-49) that exhibits a negative gas adsorption; that is, spontaneous desorption of gas (methane and n-butane) occurs during pressure increase in a defined temperature and pressure range. A combination of in situ powder X-ray diffraction, gas adsorption experiments and simulations shows that this adsorption behaviour is controlled by a sudden hysteretic structural deformation and pore contraction of the MOF, which releases guest molecules. These findings may enable technologies using frameworks capable of negative gas adsorption for pressure amplification in micro- and macroscopic system engineering. Negative gas adsorption extends the series of counterintuitive phenomena such as negative thermal expansion and negative refractive indices and may be interpreted as an adsorptive analogue of force-amplifying negative compressibility transitions proposed for metamaterials.

  13. A pressure-amplifying framework material with negative gas adsorption transitions

    NASA Astrophysics Data System (ADS)

    Krause, Simon; Bon, Volodymyr; Senkovska, Irena; Stoeck, Ulrich; Wallacher, Dirk; Többens, Daniel M.; Zander, Stefan; Pillai, Renjith S.; Maurin, Guillaume; Coudert, François-Xavier; Kaskel, Stefan

    2016-04-01

    Adsorption-based phenomena are important in gas separations, such as the treatment of greenhouse-gas and toxic-gas pollutants, and in water-adsorption-based heat pumps for solar cooling systems. The ability to tune the pore size, shape and functionality of crystalline porous coordination polymers—or metal-organic frameworks (MOFs)—has made them attractive materials for such adsorption-based applications. The flexibility and guest-molecule-dependent response of MOFs give rise to unexpected and often desirable adsorption phenomena. Common to all isothermal gas adsorption phenomena, however, is increased gas uptake with increased pressure. Here we report adsorption transitions in the isotherms of a MOF (DUT-49) that exhibits a negative gas adsorption; that is, spontaneous desorption of gas (methane and n-butane) occurs during pressure increase in a defined temperature and pressure range. A combination of in situ powder X-ray diffraction, gas adsorption experiments and simulations shows that this adsorption behaviour is controlled by a sudden hysteretic structural deformation and pore contraction of the MOF, which releases guest molecules. These findings may enable technologies using frameworks capable of negative gas adsorption for pressure amplification in micro- and macroscopic system engineering. Negative gas adsorption extends the series of counterintuitive phenomena such as negative thermal expansion and negative refractive indices and may be interpreted as an adsorptive analogue of force-amplifying negative compressibility transitions proposed for metamaterials.

  14. Regenerable adsorption system

    NASA Technical Reports Server (NTRS)

    Roychoudhury, Subir (Inventor); Perry, Jay (Inventor); Walsh, Dennis (Inventor)

    2006-01-01

    A method for regenerable adsorption includes providing a substrate that defines at least one layer of ultra short channel length mesh capable of conducting an electrical current therethrough, coating at least a portion of the substrate with a desired sorbent for trace contaminant control or CO.sub.2 sorption, resistively heating the substrate, and passing a flowstream through the substrate and in contact with the sorbent.

  15. Assessing the adsorption properties of shales

    NASA Astrophysics Data System (ADS)

    Pini, Ronny

    2015-04-01

    Physical adsorption refers to the trapping of fluid molecules at near liquid-like densities in the pores of a given adsorbent material. Fine-grained rocks, such as shales, contain a significant amount of nanopores that can significantly contribute to their storage capacity. As a matter of fact, the current ability to extract natural gas that is adsorbed in the rock's matrix is limited, and current technology focuses primarily on the free gas in the fractures (either natural or stimulated), thus leading to recovery efficiencies that are very low. Shales constitute also a great portion of so-called cap-rocks above potential CO2 sequestration sites; hereby, the adsorption process may limit the CO2 mobility within the cap-rock, thus minimizing the impact of leakage on the whole operation. Whether it is an unconventional reservoir or a cap-rock, understanding and quantifying the mechanisms of adsorption in these natural materials is key to improve the engineering design of subsurface operations. Results will be presented from a laboratory study that combines conventional techniques for the measurement of adsorption isotherms with novel methods that allows for the imaging of adsorption using x-rays. Various nanoporous materials are considered, thus including rocks, such as shales and coals, pure clay minerals (a major component in mudrocks) and engineered adsorbents with well-defined nanopore structures, such as zeolites. Supercritical CO2 adsorption isotherms have been measured with a Rubotherm Magnetic Suspension balance by covering the pressure range 0.1-20~MPa. A medical x-ray CT scanner has been used to identify three-dimensional patterns of the adsorption properties of a packed-bed of adsorbent, thus enabling to assess the spatial variability of the adsorption isotherm in heterogeneous materials. The data are analyzed by using thermodynamically rigorous measures of adsorption, such as the net- and excess adsorbed amounts and a recently developed methodology is

  16. Diffusion Influenced Adsorption Kinetics.

    PubMed

    Miura, Toshiaki; Seki, Kazuhiko

    2015-08-27

    When the kinetics of adsorption is influenced by the diffusive flow of solutes, the solute concentration at the surface is influenced by the surface coverage of solutes, which is given by the Langmuir-Hinshelwood adsorption equation. The diffusion equation with the boundary condition given by the Langmuir-Hinshelwood adsorption equation leads to the nonlinear integro-differential equation for the surface coverage. In this paper, we solved the nonlinear integro-differential equation using the Grünwald-Letnikov formula developed to solve fractional kinetics. Guided by the numerical results, analytical expressions for the upper and lower bounds of the exact numerical results were obtained. The upper and lower bounds were close to the exact numerical results in the diffusion- and reaction-controlled limits, respectively. We examined the validity of the two simple analytical expressions obtained in the diffusion-controlled limit. The results were generalized to include the effect of dispersive diffusion. We also investigated the effect of molecular rearrangement of anisotropic molecules on surface coverage.

  17. Carbon adsorption onsite for remedial actions

    SciTech Connect

    Githens, G.D.

    1984-01-01

    Environmental remediation options range from various offsite disposal methods to onsite concentration, treatment or storage. Onsite treatment using mobile carbon adsorption treatment systems has long been a favored option for remedial actions because of its proven performance in the clean-up of transportation spills, waste sites, runoff from chemical warehouse fires and many types of groundwater pollution. Carbon adsorption is fundamentally a concentration technology. It will, for example, preferentially concentrate organics. Following its use, the carbon is usually transported offsite for thermal regeneration (mobile regeneration is not generally available) or landfilled if certain contaminants such as PCBs are on the carbon. Most remediation projects are temporary in nature and involve removing contamination from finite areas to attain specific pollutant limits. The best way to approach these circumstances is to utilize mobile, rapidly deployed, modular units. With mobile pretreatment equipment, the field engineer can solve problems with control over cost and system performance.

  18. Evaluating the Adsorptive Capacities of Chemsorb 1000 and Chemsorb 1425

    NASA Technical Reports Server (NTRS)

    Monje, Oscar Alberto Monje; Surma, Jan M.; Johnsey, Marissa N.; Melendez, Orlando

    2014-01-01

    The Air Revitalization Lab at KSC tested Chemsorb 1000 and 1425, two candidate sorbents for use in future air revitalization technologies being evaluated by the ARREM project. Chemsorb 1000 and 1425 are granular coconut-shell activated carbon sorbents produced by Molecular Products, Inc. that may be used in the TCCS. Chemsorb 1000 is a high grade activated carbon for organic vapor adsorption. In contrast, Chemsorb 1425 is a high-grade impregnated activated carbon for adsorption of airborne ammonia and amines. Chemsorb 1000 was challenged with simulated spacecraft gas streams in order to determine its adsorptive capacities for mixtures of volatile organics compounds. Chemsorb 1425 was challenged with various NH3 concentrations to determine its adsorptive capacity.

  19. EPA/NSF ETV Equipment Verification Testing Plan for the Removal of Volatile Organic Chemical Contaminants by Adsorptive Media Processes

    EPA Science Inventory

    This document is the Environmental Technology Verification (ETV) Technology Specific Test Plan (TSTP) for evaluation of drinking water treatment equipment utilizing adsorptive media for synthetic organic chemical (SOC) removal. This TSTP is to be used within the structure provid...

  20. Interfacial adsorption and aggregation of amphiphilic proteins

    NASA Astrophysics Data System (ADS)

    Cheung, David

    2012-02-01

    The adsorption and aggregation on liquid interfaces of proteins is important in many biological contexts, such as the formation of aerial structures, immune response, and catalysis. Likewise the adsorption of proteins onto interfaces has applications in food technology, drug delivery, and in personal care products. As such there has been much interest in the study of a wide range of biomolecules at liquid interfaces. One class of proteins that has attracted particular attention are hydrophobins, small, fungal proteins with a distinct, amphiphilic surface structure. This makes these proteins highly surface active and they recently attracted much interest. In order to understand their potential applications a microscopic description of their interfacial and self-assembly is necessary and molecular simulation provides a powerful tool for providing this. In this presentation I will describe some recent work using coarse-grained molecular dynamics simulations to study the interfacial and aggregation behaviour of hydrophobins. Specifically this will present the calculation of their adsorption strength at oil-water and air-water interfaces, investigate the stability of hydrophobin aggregates in solution and their interaction with surfactants.

  1. Liquid-Phase Adsorption Fundamentals.

    ERIC Educational Resources Information Center

    Cooney, David O.

    1987-01-01

    Describes an experiment developed and used in the unit operations laboratory course at the University of Wyoming. Involves the liquid-phase adsorption of an organic compound from aqueous solution on activated carbon, and is relevant to adsorption processes in general. (TW)

  2. Effects of Cabin Upsets on Adsorption Columns for Air Revitalization

    NASA Technical Reports Server (NTRS)

    LeVan, Douglas

    1999-01-01

    The National Aeronautics and Space Administration (NASA) utilizes adsorption technology as part of contaminant removal systems designed for long term missions. A variety of trace contaminants can be effectively removed from gas streams by adsorption onto activated carbon. An activated carbon adsorption column meets NASA's requirements of a lightweight and efficient means of controlling trace contaminant levels aboard spacecraft and space stations. The activated carbon bed is part of the Trace Contaminant Control System (TCCS) which is utilized to purify the cabin atmosphere. TCCS designs oversize the adsorption columns to account for irregular fluctuations in cabin atmospheric conditions. Variations in the cabin atmosphere include changes in contaminant concentrations, temperature, and relative humidity. Excessively large deviations from typical conditions can result from unusual crew activity, equipment malfunctions, or even fires. The research carried out under this award focussed in detail on the effects of cabin upsets on the performance of activated carbon adsorption columns. Both experiments and modeling were performed with an emphasis on the roll of a change in relative humidity on adsorption of trace contaminants. A flow through fixed-bed apparatus was constructed at the NASA Ames Research Center, and experiments were performed there. Modeling work was performed at the University of Virginia.

  3. Reverse osmosis concentrate treatment via a PAC-MF accumulative countercurrent adsorption process.

    PubMed

    Zhao, Chunxia; Gu, Ping; Cui, Hangyu; Zhang, Guanghui

    2012-01-01

    Organic pollutants in reverse osmosis (RO) concentrates from wastewater reclamation are mainly comprised of low molecular weight biorefractory compounds. Generally, advanced oxidation methods for oxidizing these organics require a relatively high level of energy consumption. In addition, conventional adsorption removal methods require a large dose of activated carbon. However, the dose can be reduced if its full adsorption capacity can be used. Therefore, the combined technology of powdered activated carbon (PAC) adsorption and microfiltration (MF) membrane filtration was studied to develop a countercurrent two-stage adsorption process. A PAC accumulative adsorption prediction method was proposed based on the verification of a PAC multi-stage adsorption capacity equation. Moreover, the prediction method was amended for a more accurate prediction of the effluent quality because adsorption isotherm constants were affected by the initial adsorbate concentration. The required PAC dose for the accumulative countercurrent two-stage adsorption system was 0.6 g/L, whereas that of the conventional adsorption process was 1.05 g/L when the dilution factor(F) was 0.1 and the COD and DOC removal rates were set to 70% and 68.1%, respectively. Organic pollutants were satisfactorily removed with less consumption of PAC. Effluent from this combined technology can be further reclaimed by an RO process to improve the overall recovery rate to between 91.0% and 93.8% with both economic and environmental benefits.

  4. Arsenic Removal: Adsorptive Media and Coagulation/Filtration Case Studies

    EPA Science Inventory

    This presentation provides information on the results of three case studies from USEPA arsenic demonstration program. The first case study presented is on the Rimrock, AZ project that used an adsorptive media technology (E33 media) to remove arsenic. The second case study is on...

  5. [Modification of natural siderite and enhanced adsorption of arsenic].

    PubMed

    Zhao, Kai; Guo, Hua-Ming; Li, Yuan; Ren, Yan

    2012-02-01

    Groundwater with high arsenic concentration has widely been found in China. More attention has been paid to economic and efficient arsenic removal technology. Natural siderite, which was abundant and relatively cheap, was used as the main raw material for arsenic adsorption by batch methods. Modified conditions of natural siderite, including temperature and time of calcination and adhesive addition, were carried out for arsenic removal. Results showed that the maximum removal efficiency was reached with the calcination temperature of 350 degrees C for 90 minutes and an adhesive dosage of 10 mg x g(-1). With the ratio of solid to liquid of 0.5 g: 50 mL and the initial concentration of 5 mg x L(-1) for either As(III) or As(V) at 25 degrees C, arsenic concentrations at equilibrium time were lower than 10 microg x L(-1). Characteristics of adsorption kinetics and adsorption isotherm on the optimal modified adsorbent were also evaluated. It was found that the arsenic adsorption kinetics fitted pseudo-second order kinetics equation, and the adsorption achieved equilibrium at about 12 h. The adsorption isotherm could be well described by Langmuir and Freundlich models. The maximum adsorption capacity was 1039 microg x g(-1) for As(III) and 1 026 microg x g(-1) for As(V). Furthermore, X-ray diffraction (XRD), scanning electron microscopy (SEM), and BET method were used to investigate main mechanisms of arsenic removal. Results showed that modified adsorbent had higher specific surface area and contained the spherical coating of Fe(II) and Fe(III) on the surface, in comparison with pristine material, which were believed to contribute to the high adsorption capacity of the modified material. The modified natural siderite appears to be a promising adsorbent that is worthy of further studies and practical application for arsenic removal.

  6. Chromium adsorption by lignin

    SciTech Connect

    Lalvani, S.B.; Huebner, A.; Wiltowski, T.S.

    2000-01-01

    Hexavalent chromium is a known carcinogen, and its maximum contamination level in drinking water is determined by the US Environmental Protection Agency (EPA). Chromium in the wastewaters from plating and metal finishing, tanning, and photographic industries poses environmental problems. A commercially available lignin was used for the removal of hexavalent as well as trivalent chromium from aqueous solution. It is known that hexavalent chromium is present as an anionic species in the solution. It was found that lignin can remove up to 63% hexavalent and 100% trivalent chromium from aqueous solutions. The removal of chromium ions was also investigated using a commercially available activated carbon. This absorbent facilitated very little hexavalent and almost complete trivalent chromium removal. Adsorption isotherms and kinetics data on the metal removal by lignin and activated carbon are presented and discussed.

  7. High temperature adsorption measurements

    SciTech Connect

    Bertani, R.; Parisi, L.; Perini, R.; Tarquini, B.

    1996-12-31

    Adsorption phenomena are a rich and rather new field of study in geothermal research, in particular at very high temperature. ENEL is interested in the exploitation of geothermal regions with super-heated steam, and it is important to understand the behavior of water-rock interaction. We have analyzed in the 170-200{degrees}C temperature range four samples of Monteverdi cuttings; the next experimental effort will be at 220{degrees}C and over in 1996. The first results of the 1995 runs are collected in this paper. We can highlight four main items: (1) At relative pressures over 0.6 the capillarity forces are very important. (2) There is no significant temperature effect. (3) Adsorbed water can be present, and it is able to multiply by a factor of 15 the estimated reserve of super-heated steam only. (4) Pores smaller than 15 {Angstrom} do not contribute to the adsorbed mass.

  8. High temperature adsorption measurements

    SciTech Connect

    Bertani, R.; Parisi, L.; Perini, R.; Tarquini, B.

    1996-01-24

    Adsorption phenomena are a rich and rather new field of study in geothermal research, in particular at very high temperature. ENEL is interested in the exploitation of geothermal regions with superheated steam, and it is important to understand the behavior of water-rock interaction. We have analyzed in the 170-200 °C temperature range four samples of Monteverdi cuttings; the next experimental effort will be at 220 °C and over in 1996. The first results of the 1995 runs are collected in this paper. We can highlight four main items: 1. At relative pressures over 0.6 the capillarity forces are very important. 2. There is no significant temperature effect. 3. Adsorbed water can be present, and it is able to multiply by a factor of 15 the estimated reserve of super-heated steam only. 4. Pores smaller than 15 Å do not contribute to the adsorbed mass.

  9. Intraparticle heat and mass transfer characteristics of silica-gel/water vapor adsorption

    SciTech Connect

    Yamamoto, Eri; Watanabe, Fujio; Hasatani, Masanobu

    1999-07-01

    Recently, highly efficient energy utilization systems which extensively employ adsorption phenomena such as pressure swing adsorption, heat storage, adsorption heat pump, etc. are being regarded as one of the countermeasures for environmental issues such as green house effect and ozone layer destruction. An Adsorption Heat Pump (AHP) has been investigated as one of the important techniques via which cold heat energy is obtained from waste thermal energy below 373K without using electricity and CFCs. An AHP normally consists of an adsorber and an evaporator/condenser and cold heat energy is generated by latent heat of evaporation during adsorption process. For realizing the AHP technology, it has been pointed out that the development of an adsorber with optimum heat and mass transfer characteristics is essentially important. In this study, experimental studies were carried out which was based on the data of temperature inside the adsorbent particle and adsorptivity profiles at the adsorption/desorption process by volumetric method. To clarify adsorption mechanism relatively large silica-gel particle (7 mm f) was used. Temperature distribution in the particle is determined at the center, at one half radius in the radial direction and at the surface by using very thin (30 mm f) thermocouples. The temperatures at these points simultaneously increase/decrease as soon as the adsorption/desorption started, reached their respective maximum/minimum values and then return to initial temperature. The temperature profiles for the adsorption process show that the temperature at the surface is initially slightly higher than the other two points. All three points reached their respective maximum temperature at the same time with the temperature at the center point the highest and at the surface the lowest. The temperature profiles during the desorptive process are almost exactly the opposite to that of the adsorption process. This shows that the adsorption phenomena can take

  10. Adsorption Processes in Spacecraft Environmental Control and Life Support Systems

    NASA Technical Reports Server (NTRS)

    Bauman, Liese Dall; Finn, John E.; Kliss, Mark (Technical Monitor)

    1998-01-01

    The environmental control and life support system on a spacecraft must maintain a safe and comfortable environment in which the crew can live and work. The system's functions include supplying the crew with oxygen and water as well as removing carbon dioxide, water vapor, and trace contaminants from cabin air. Although open-loop systems have been used in the past, logistics and safety factors of current and future missions in space make near-complete recycling of the cabin's air and water imperative. The recycling process may include separation and reduction of carbon dioxide, removal of trace gas-phase contaminants, recovery and purification of humidity condensate, purification and polishing of wastewater streams, and other processes. Several of these operations can be performed totally or in part by adsorption processes. These processes are frequently good candidates to perform separations and purifications in space due to their gravity independence, high reliability, relatively high energy efficiency, design flexibility, technological maturity, and regenerability. For these reasons, adsorption has historically played a key role in life support on U.S. and Russian piloted spacecraft. This article focuses on three current spacecraft life support applications that often use adsorption technology: gas-phase trace contaminant control, carbon dioxide removal from cabin air, and potable water recovery from waste streams. In each application, adsorption technology has been selected for use on the International Space Station. The requirements, science, and hardware for each of these applications are discussed. Eventually, human space exploration may lead to construction of planetary habitats. These habitats may provide additional opportunities for use of adsorption processes, such as control of greenhouse gas composition, and may have different requirements and resources available to them, such as gases present in the planetary atmosphere. Adsorption separation and

  11. Adsorption processes in spacecraft environmental control and life support systems

    NASA Technical Reports Server (NTRS)

    DallBauman, L. A.; Finn, J. E.

    1999-01-01

    The environmental control and life support system on a spacecraft maintains a safe and comfortable environment in which the crew can live and work by supplying oxygen and water and by removing carbon dioxide, water vapor, and trace contaminants from cabin air. Although open-loop systems have been used successfully in the past for short-duration missions, the economics of current and future long-duration missions in space will make nearly complete recycling of air and water imperative. A variety of operations will be necessary to achieve the goal of nearly complete recycling. These include separation and reduction of carbon dioxide, removal of trace gas-phase contaminants, recovery and purification of humidity condensate, purification and polishing of wastewater streams, and others. Several of these can be performed totally or in part by adsorption processes. These processes are good candidates to perform separations and purifications in space due to their gravity independence, high reliability, relative high energy efficiency, design flexibility, technological maturity, and regenerative nature. For these reasons, adsorption has historically played a key role in life support on U.S. and Russian piloted spacecraft. Among the life support applications that can be achieved through use of adsorption technology are removal of trace contaminants and carbon dioxide from cabin air and recovery of potable water from waste streams. In each of these cases adsorption technology has been selected for use onboard the International Space Station. The requirements, science, and hardware for these applications are discussed. Human space exploration may eventually lead to construction of planetary habitats. These habitats may provide additional opportunities for use of adsorption processes, such as control of greenhouse gas composition, and may have different resources available to them, such as gases present in the planetary atmosphere. Separation and purification processes based on

  12. Adsorption processes in spacecraft environmental control and life support systems.

    PubMed

    DallBauman, L A; Finn, J E

    1999-01-01

    The environmental control and life support system on a spacecraft maintains a safe and comfortable environment in which the crew can live and work by supplying oxygen and water and by removing carbon dioxide, water vapor, and trace contaminants from cabin air. Although open-loop systems have been used successfully in the past for short-duration missions, the economics of current and future long-duration missions in space will make nearly complete recycling of air and water imperative. A variety of operations will be necessary to achieve the goal of nearly complete recycling. These include separation and reduction of carbon dioxide, removal of trace gas-phase contaminants, recovery and purification of humidity condensate, purification and polishing of wastewater streams, and others. Several of these can be performed totally or in part by adsorption processes. These processes are good candidates to perform separations and purifications in space due to their gravity independence, high reliability, relative high energy efficiency, design flexibility, technological maturity, and regenerative nature. For these reasons, adsorption has historically played a key role in life support on U.S. and Russian piloted spacecraft. Among the life support applications that can be achieved through use of adsorption technology are removal of trace contaminants and carbon dioxide from cabin air and recovery of potable water from waste streams. In each of these cases adsorption technology has been selected for use onboard the International Space Station. The requirements, science, and hardware for these applications are discussed. Human space exploration may eventually lead to construction of planetary habitats. These habitats may provide additional opportunities for use of adsorption processes, such as control of greenhouse gas composition, and may have different resources available to them, such as gases present in the planetary atmosphere. Separation and purification processes based on

  13. Random sequential adsorption on fractals.

    PubMed

    Ciesla, Michal; Barbasz, Jakub

    2012-07-28

    Irreversible adsorption of spheres on flat collectors having dimension d < 2 is studied. Molecules are adsorbed on Sierpinski's triangle and carpet-like fractals (1 < d < 2), and on general Cantor set (d < 1). Adsorption process is modeled numerically using random sequential adsorption (RSA) algorithm. The paper concentrates on measurement of fundamental properties of coverages, i.e., maximal random coverage ratio and density autocorrelation function, as well as RSA kinetics. Obtained results allow to improve phenomenological relation between maximal random coverage ratio and collector dimension. Moreover, simulations show that, in general, most of known dimensional properties of adsorbed monolayers are valid for non-integer dimensions.

  14. Galactose adsorption on Ru(0001)

    NASA Astrophysics Data System (ADS)

    Alatalo, Matti; Puisto, Mikko

    2014-03-01

    In order to understand the valorisation of biomass, it is essential to study the behavior of sugar molecules on catalytic surfaces. We have studied the adsorption of galactose molecules on the Ru(0001) surface using first principles calculations. We present results for the fully relaxed configurations of the molecule at different adsorption sites. We also compare the effect of the inclusion of the van der Waals interactions on both the energetics of the free galactose molecule and the adsorption energy of galactose on Ru(0001). We compare our results, obtained using periodically repeated supercells, to those obtained with cluster calculations.

  15. Arsenic Removal from Drinking Water by Point of Entry/Point of Use Adsorptive Media U.S. EPA Demonstration Project at Oregon Institute of Technology at Klamath Falls, OR - Final Performance Evaluation Report

    EPA Science Inventory

    This report documents the activities performed during and the results obtained from the arsenic removal treatment technology demonstration project at Oregon Institute of Technology (OIT) at Klamath Falls, OR. The objectives of the project were to evaluate: (1) the effectiveness...

  16. Protein Adsorption in Three Dimensions

    PubMed Central

    Vogler, Erwin A.

    2011-01-01

    Recent experimental and theoretical work clarifying the physical chemistry of blood-protein adsorption from aqueous-buffer solution to various kinds of surfaces is reviewed and interpreted within the context of biomaterial applications, especially toward development of cardiovascular biomaterials. The importance of this subject in biomaterials surface science is emphasized by reducing the “protein-adsorption problem” to three core questions that require quantitative answer. An overview of the protein-adsorption literature identifies some of the sources of inconsistency among many investigators participating in more than five decades of focused research. A tutorial on the fundamental biophysical chemistry of protein adsorption sets the stage for a detailed discussion of the kinetics and thermodynamics of protein adsorption, including adsorption competition between two proteins for the same adsorbent immersed in a binary-protein mixture. Both kinetics and steady-state adsorption can be rationalized using a single interpretive paradigm asserting that protein molecules partition from solution into a three-dimensional (3D) interphase separating bulk solution from the physical-adsorbent surface. Adsorbed protein collects in one-or-more adsorbed layers, depending on protein size, solution concentration, and adsorbent surface energy (water wettability). The adsorption process begins with the hydration of an adsorbent surface brought into contact with an aqueous-protein solution. Surface hydration reactions instantaneously form a thin, pseudo-2D interface between the adsorbent and protein solution. Protein molecules rapidly diffuse into this newly-formed interface, creating a truly 3D interphase that inflates with arriving proteins and fills to capacity within milliseconds at mg/mL bulk-solution concentrations CB. This inflated interphase subsequently undergoes time-dependent (minutes-to-hours) decrease in volume VI by expulsion of either-or-both interphase water and

  17. Bromide Adsorption by Reference Minerals and Soils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Bromide, Br-, adsorption behavior was investigated on amorphous Al and Fe oxide, montmorillonite, kaolinite, and temperate and tropical soils. Bromide adsorption decreased with increasing solution pH with minimal adsorption occurring above pH 7. Bromide adsorption was higher for amorphous oxides t...

  18. Centrifugal Adsorption Cartridge System

    NASA Technical Reports Server (NTRS)

    Gonda, Steve R.; Tsao, Yow-Min D.; Lee, Wenshan

    2004-01-01

    The centrifugal adsorption cartridge system (CACS) is an apparatus that recovers one or more bioproduct(s) from a dilute aqueous solution or suspension flowing from a bioreactor. The CACS can be used both on Earth in unit gravity and in space in low gravity. The CACS can be connected downstream from the bioreactor; alternatively, it can be connected into a flow loop that includes the bioreactor so that the liquid can be recycled. A centrifugal adsorption cartridge in the CACS (see figure) includes two concentric cylinders with a spiral ramp between them. The volume between the inner and outer cylinders, and between the turns of the spiral ramp is packed with an adsorbent material. The inner cylinder is a sieve tube covered with a gas-permeable, hydrophobic membrane. During operation, the liquid effluent from the bioreactor is introduced at one end of the spiral ramp, which then constrains the liquid to flow along the spiral path through the adsorbent material. The spiral ramp also makes the flow more nearly uniform than it would otherwise be, and it minimizes any channeling other than that of the spiral flow itself. The adsorbent material is formulated to selectively capture the bioproduct(s) of interest. The bioproduct(s) can then be stored in bound form in the cartridge or else eluted from the cartridge. The centrifugal effect of the spiral flow is utilized to remove gas bubbles from the liquid. The centrifugal effect forces the bubbles radially inward, toward and through the membrane of the inner cylinder. The gas-permeable, hydrophobic membrane allows the bubbles to enter the inner cylinder while keeping the liquid out. The bubbles that thus enter the cylinder are vented to the atmosphere. The spacing between the ramps determines rate of flow along the spiral, and thereby affects the air-bubble-removal efficiency. The spacing between the ramps also determines the length of the fluid path through the cartridge adsorbent, and thus affects the bioproduct

  19. Multilayer adsorption on fractal surfaces.

    PubMed

    Vajda, Péter; Felinger, Attila

    2014-01-10

    Multilayer adsorption is often observed in liquid chromatography. The most frequently employed model for multilayer adsorption is the BET isotherm equation. In this study we introduce an interpretation of multilayer adsorption measured on liquid chromatographic stationary phases based on the fractal theory. The fractal BET isotherm model was successfully used to determine the apparent fractal dimension of the adsorbent surface. The nonlinear fitting of the fractal BET equation gives us the estimation of the adsorption equilibrium constants and the monolayer saturation capacity of the adsorbent as well. In our experiments, aniline and proline were used as test molecules on reversed phase and normal phase columns, respectively. Our results suggest an apparent fractal dimension 2.88-2.99 in the case of reversed phase adsorbents, in the contrast with a bare silica column with a fractal dimension of 2.54.

  20. Short-Cycle Adsorption Refrigerator

    NASA Technical Reports Server (NTRS)

    Chan, C. K.

    1988-01-01

    Modular adsorption/Joule-Thomson-effect refrigerator offers fast regeneration; adsorption/desorption cycle time expected to be 1 minute. Pressurized hydrogen generated by bank of compressor modules during heating phase passes through system of check valves and expands in Joule-Thomson junction as it enters refrigeration chamber. Hydrogen absorbs heat from load before it is sucked out by another bank of compressor modules in cooling phase.

  1. Adsorption hysteresis in nanopores

    PubMed

    Neimark; Ravikovitch; Vishnyakov

    2000-08-01

    Capillary condensation hysteresis in nanopores is studied by Monte Carlo simulations and the nonlocal density functional theory. Comparing the theoretical results with the experimental data on low temperature sorption of nitrogen and argon in cylindrical channels of mesoporous siliceous molecular sieves of MCM-41 type, we have revealed four qualitatively different sorption regimes depending on the temperature and pore size. As the pore size increases at a given temperature, or as the temperature decreases at a given pore size, the following regimes are consequently observed: volume filling without phase separation, reversible stepwise capillary condensation, irreversible capillary condensation with developing hysteresis, and capillary condensation with developed hysteresis. We show that, in the regime of developed hysteresis (pores wider than 5 nm in the case of nitrogen sorption at 77 K), condensation occurs spontaneously at the vaporlike spinodal while desorption takes place at the equilibrium. A quantitative agreement is found between the modeling results and the experimental hysteresis loops formed by the adsorption-desorption isotherms. The results obtained provide a better understanding of the general behavior of confined fluids and the specifics of sorption and phase transitions in nanomaterials.

  2. Challenges in hydrogen adsorptions: from physisorption to chemisorption

    NASA Astrophysics Data System (ADS)

    Ding, Feng; Yakobson, Boris I.

    2011-06-01

    In this short review, we will briefly discuss the story of hydrogen storage, its impact on clean energy application, especially the challenges of using hydrogen adsorption for onboard application. After a short comparison of the main methods of hydrogen storage (high pressure tank, metal hydride and adsorption), we will focus our discussion on adsorption of hydrogen in graphitic carbon based large surface area adsorbents including carbon nanotubes, graphene and metal organic frameworks. The mechanisms, advantages, disadvantages and recent progresses will be discussed and reviewed for physisorption, metal-assisted storage and chemisorption. In the last section, we will discuss hydrogen spillover chemisorption in detail for the mechanism, status, challenges and perspectives. We hope to present a clear picture of the present technologies, challenges and the perspectives of hydrogen storage for the future studies.

  3. Sequential anaerobic-adsorption treatment of chemical industry wastewater.

    PubMed

    Daga, Kailash; Pallavi, V; Patel, Dharmendra

    2011-10-01

    Treatment technologies needed to reduce the pollutant load of chemical industry effluent have been found to involve exorbitantly high costs. The present investigation aimed to treat the wastewater from chemical industry by cost effective sequential anaerobic-adsorption treatment. Wastewaters from chemical industry that are rich in biodegradable organics are tested for anaerobic treatability. The efficiency of anaerobic reactor is relatively lower 79.3%, and therefore post treatment of effluent was done by adsorption using Poly vinyl alcohol coated Datura stramonium (PVAC-DS) as an adsorbent. An overall COD removal of 93.8 % was achieved after sequential Anaerobic-Adsorption treatment, which lead to a better final effluent and a more economical treatment system.

  4. Surfactant adsorption kinetics in microfluidics

    PubMed Central

    Riechers, Birte; Maes, Florine; Akoury, Elias; Semin, Benoît; Gruner, Philipp; Baret, Jean-Christophe

    2016-01-01

    Emulsions are metastable dispersions. Their lifetimes are directly related to the dynamics of surfactants. We design a microfluidic method to measure the kinetics of adsorption of surfactants to the droplet interface, a key process involved in foaming, emulsification, and droplet coarsening. The method is based on the pH decay in the droplet as a direct measurement of the adsorption of a carboxylic acid surfactant to the interface. From the kinetic measurement of the bulk equilibration of the pH, we fully determine the adsorption process of the surfactant. The small droplet size and the convection during the droplet flow ensure that the transport of surfactant through the bulk is not limiting the kinetics of adsorption. To validate our measurements, we show that the adsorption process determines the timescale required to stabilize droplets against coalescence, and we show that the interface should be covered at more than 90% to prevent coalescence. We therefore quantitatively link the process of adsorption/desorption, the stabilization of emulsions, and the kinetics of solute partitioning—here through ion exchange—unraveling the timescales governing these processes. Our method can be further generalized to other surfactants, including nonionic surfactants, by making use of fluorophore–surfactant interactions. PMID:27688765

  5. Surfactant adsorption kinetics in microfluidics

    NASA Astrophysics Data System (ADS)

    Riechers, Birte; Maes, Florine; Akoury, Elias; Semin, Benoît; Gruner, Philipp; Baret, Jean-Christophe

    2016-10-01

    Emulsions are metastable dispersions. Their lifetimes are directly related to the dynamics of surfactants. We design a microfluidic method to measure the kinetics of adsorption of surfactants to the droplet interface, a key process involved in foaming, emulsification, and droplet coarsening. The method is based on the pH decay in the droplet as a direct measurement of the adsorption of a carboxylic acid surfactant to the interface. From the kinetic measurement of the bulk equilibration of the pH, we fully determine the adsorption process of the surfactant. The small droplet size and the convection during the droplet flow ensure that the transport of surfactant through the bulk is not limiting the kinetics of adsorption. To validate our measurements, we show that the adsorption process determines the timescale required to stabilize droplets against coalescence, and we show that the interface should be covered at more than 90% to prevent coalescence. We therefore quantitatively link the process of adsorption/desorption, the stabilization of emulsions, and the kinetics of solute partitioning—here through ion exchange—unraveling the timescales governing these processes. Our method can be further generalized to other surfactants, including nonionic surfactants, by making use of fluorophore-surfactant interactions.

  6. High gradient magnetic separation versus expanded bed adsorption: a first principle comparison.

    PubMed

    Hubbuch, J J; Matthiesen, D B; Hobley, T J; Thomas, O R

    2001-01-01

    A robust new adsorptive separation technique specifically designed for direct product capture from crude bioprocess feedstreams is introduced and compared with the current bench mark technique, expanded bed adsorption. The method employs product adsorption onto sub-micron sized non-porous superparamagnetic supports followed by rapid separation of the 'loaded' adsorbents from the feedstock using high gradient magnetic separation technology. For the recovery of Savinase from a cell-free Bacillus clausii fermentation liquor using bacitracin-linked adsorbents, the integrated magnetic separation system exhibited substantially enhanced productivity over expanded bed adsorption when operated at processing velocities greater than 48 m h(-1). Use of the bacitracin-linked magnetic supports for a single cycle of batch adsorption and subsequent capture by high gradient magnetic separation at a processing rate of 12 m h(-1) resulted in a 2.2-fold higher productivity relative to expanded bed adsorption, while an increase in adsorbent collection rate to 72 m h(-1) raised the productivity to 10.7 times that of expanded bed adsorption. When the number of batch adsorption cycles was then increased to three, significant drops in both magnetic adsorbent consumption (3.6 fold) and filter volume required (1.3 fold) could be achieved at the expense of a reduction in productivity from 10.7 to 4.4 times that of expanded bed adsorption.

  7. A Study of Adsorptive Characteristics of Australian Coals

    NASA Astrophysics Data System (ADS)

    Lan, Y. P.; Tsai, L. L.

    2012-04-01

    Ever since the Kyoto Protocol, controlling carbon dioxide emission and reducing its content in atmosphere are very important environmental issues up to today. One of the effective methods for permanent sequestration of anthropogenic CO2 is to inject CO2 into deep, unminable coal seams and recover coal bed methane at the same time. CO2-ECBM technology had been proved to be very promising to meet the needs of both environment and energy. Beside other external environment factors, capacity of CO2 adsorption and CH4 desorption are the most influencing factors in selection of sites for the geological storage of CO2. Therefore, the objective of this study is to understand the relationship between gas adsorption and CO2 sequestration, by various experiments for the characterization of Australian of coals. Generally speaking, coal seam gas comprises mostly of CH4, CO2, C2H6, and N2. However, some of the Australian coals were reported with significant amount of CO2 up to 90%, which might strongly affect their capacity of CO2 capture and storage (CCS). High to medium volatile bituminous coals from Sydney Basin and Bowen Basin, southeast Australia were selected in this study. Experiments include maceral composition and vitrinite reflectance measurements, petrographic analysis, Proximate analysis, Ultimate analysis, specific surface area analysis as well as CO2 and CH4 adsorption experiments were performed. Parameters for difference adsorption functions (Langmuir, BET, D-R and D-A) were then calculated to fit their adsorption isotherms the best fitting curve can then be found. Among these adsorption functions, Langmuir is the most basic and commonly used function theory. The results of all experiments were synthesized to discuss the relations among each other, so as to establish the relationship between gas adsorption and coal characteristics.

  8. Electrokinetic investigation of surfactant adsorption.

    PubMed

    Bellmann, C; Synytska, A; Caspari, A; Drechsler, A; Grundke, K

    2007-05-15

    Fuerstenau [D.W. Fuerstenau, in: M.L. Hair (Ed.), Dekker, New York, 1971, p. 143] has already discussed the role of hydrocarbon chain of surfactants, the effect of alkyl chain length, chain structure and the pH of the solution on the adsorption process of surfactants. Later Kosmulski [M. Kosmulski, Chemical Properties of Material Surfaces, Surfactant Science Series, vol. 102, Dekker, New York, Basel, 2001] included the effect of surfactant concentration, equilibration time, temperature and electrolyte in his approaches. Certainly, the character of the head groups of the surfactant and the properties of the adsorbent surface are the basis for the adsorption process. Different surfactants and adsorbents cause different adsorption mechanisms described firstly by Rosen [M.J. Rosen, Surfactants and Interfacial Phenomena, second ed., Wiley, New York, 1989]. These adsorption mechanisms and their influencing factors were studied by electrokinetic investigations. Here only changes of the charges at the surfaces could be detected. To control the results of electrokinetic investigations they were compared with results from ellipsometric measurements. In the case of surfactant adsorption the chain length was vitally important. It could be shown by the adsorption of alkyl trimethyl ammonium bromides onto polymer films spin coated at wafer surfaces. The influence of the chain length depending on surface properties of the polymer film was studied. Streaming potential measurements were applied for these investigations. The obtained results enabled us to calculate the molar cohesive free energy per mol of CH2-group in the alkaline chain of the surfactant if all other specific adsorption effects were neglected.

  9. Adsorption of oxygen on W/100/ - Adsorption kinetics and structure

    NASA Technical Reports Server (NTRS)

    Bauer, E.; Poppa, H.; Viswanath, Y.

    1976-01-01

    The adsorption of oxygen on W(100) single-crystal surfaces is studied by Auger electron spectroscopy (AES), flash desorption, low-energy electron diffraction (LEED), and retarding-field work-function measurements. The AES results reveal stepwise changes in the sticking coefficients in the coverage range 0 to 1 and activated adsorption at higher coverages. Upon room-temperature adsorption, a series of complex LEED patterns is observed. In layers adsorbed at 1050 K and cooled to room temperature, the p(2 x 1) structure is the first ordered structure observed. This structure shows a reversible order-disorder transition between 700 and 1000 K and is characterized by a work function which is lower than that of the clean surface. Heating room-temperature adsorbates changes their structure irreversibly. At temperatures below 750 K, some new structures are observed.

  10. Adsorption Properties of Lignin-derived Activated Carbon Fibers (LACF)

    SciTech Connect

    Contescu, Cristian I.; Gallego, Nidia C.; Thibaud-Erkey, Catherine; Karra, Reddy

    2016-04-01

    The object of this CRADA project between Oak Ridge National Laboratory (ORNL) and United Technologies Research Center (UTRC) is the characterization of lignin-derived activated carbon fibers (LACF) and determination of their adsorption properties for volatile organic compounds (VOC). Carbon fibers from lignin raw materials were manufactured at Oak Ridge National Laboratory (ORNL) using the technology previously developed at ORNL. These fibers were physically activated at ORNL using various activation conditions, and their surface area and pore-size distribution were characterized by gas adsorption. Based on these properties, ORNL did down-select five differently activated LACF materials that were delivered to UTRC for measurement of VOC adsorption properties. UTRC used standard techniques based on breakthrough curves to measure and determine the adsorption properties of indoor air pollutants (IAP) - namely formaldehyde and carbon dioxide - and to verify the extent of saturated fiber regenerability by thermal treatments. The results are summarized as follows: (1) ORNL demonstrated that physical activation of lignin-derived carbon fibers can be tailored to obtain LACF with surface areas and pore size distributions matching the properties of activated carbon fibers obtained from more expensive, fossil-fuel precursors; (2) UTRC investigated the LACF potential for use in air cleaning applications currently pursued by UTRC, such as building ventilation, and demonstrated their regenerability for CO2 and formaldehyde, (3) Both partners agree that LACF have potential for possible use in air cleaning applications.

  11. Adsorptive removal of patulin from aqueous solution using thiourea modified chitosan resin.

    PubMed

    Liu, Bingjie; Peng, Xiaoning; Chen, Wei; Li, Yang; Meng, Xianghong; Wang, Dongfeng; Yu, Guangli

    2015-09-01

    In the present paper, thiourea modified chitosan resin (TMCR) was firstly prepared through converting hydroxyl groups of chitosan resin into thiol groups, using glutaraldehyde as cross-linking agent and thiourea as modification agent. TMCR was characterized by FTIR, EDXS, SEM, XRD and AFM technologies. Batch adsorption experiments were performed to study the adsorption capacity of TMCR for patulin at different pH, temperature, contact time and patulin concentration. The result showed that TMCR was effective in removal of patulin from aqueous solution. The adsorption capacity of TMCR for patulin was 1.0 mg/g at pH 4.0, 25 °C for 24 h. Adsorption process could be well described by pseudo-first order model, Freundlich isotherm model and intraparticle diffusion model. It indicated that TMCR is expected to be a new material for patulin adsorption from aqueous solutions.

  12. Screening of active metals for reactive adsorption desulfurization adsorbent using density functional theory

    NASA Astrophysics Data System (ADS)

    Wang, Lei; Zhao, Liang; Xu, Chunming; Wang, Yuxian; Gao, Jinsen

    2017-03-01

    To explore characteristics of active metals for reactive adsorption desulfurization (RADS) technology, the adsorption of thiophene on M (100) (M = Cr, Mo, Co, Ni, Cu, Au, and Ag) surfaces was systematically studied by density functional theory with vdW correction (DFT + D3). We found that, in all case, the most stable molecular adsorption site was the hollow site and adsorptive capabilities of thiophene followed the order: Cr > Mo > Co ≈ Ni > Cu > Au ≈ Ag. By analyzing the nature of binding between thiophene and corresponding metals and the electronic structure of metals, the excessive activities of Cr and Mo were found to have a negative regeneration, the passive activities of Au and Ag were found to have an inactive adsorption for RADS adsorbent alone, while Ni and Co have appropriate characteristics as the active metals for RADS, followed by Cu.

  13. Adsorptive desulfurization by activated alumina.

    PubMed

    Srivastav, Ankur; Srivastava, Vimal Chandra

    2009-10-30

    This study reports usage of commercial grade activated alumina (aluminum oxide) as adsorbent for the removal of sulfur from model oil (dibenthiophene (DBT) dissolved in n-hexane). Bulk density of alumina was found to be 1177.77 kg/m(3). The BET surface area of alumina was found to decrease from 143.6 to 66.4 m(2)/g after the loading of DBT at optimum conditions. The carbon-oxygen functional groups present on the surface of alumina were found to be effective in the adsorption of DBT onto alumina. Optimum adsorbent dose was found to be 20 g/l. The adsorption of DBT on alumina was found to be gradual process, and quasi-equilibrium reached in 24 h. Langmuir isotherm best represented the equilibrium adsorption data. The heat of adsorption and change in entropy for DBT adsorption onto alumina was found to be 19.5 kJ/mol and 139.2 kJ/mol K, respectively.

  14. Reduced protein adsorption by osmolytes.

    PubMed

    Evers, Florian; Steitz, Roland; Tolan, Metin; Czeslik, Claus

    2011-06-07

    Osmolytes are substances that affect osmosis and are used by cells to adapt to environmental stress. Here, we report a neutron reflectivity study on the influence of some osmolytes on protein adsorption at solid-liquid interfaces. Bovine ribonuclease A (RNase) and bovine insulin were used as model proteins adsorbing at a hydrophilic silica and at a hydrophobic polystyrene surface. From the neutron reflectivity data, the adsorbed protein layers were characterized in terms of layer thickness, protein packing density, and adsorbed protein mass in the absence and presence of urea, trehalose, sucrose, and glycerol. All data point to the clear effect of these nonionic cosolvents on the degree of protein adsorption. For example, 1 M sucrose leads to a reduction of the adsorbed amount of RNase by 39% on a silica surface and by 71% on a polystyrene surface. Trehalose was found to exhibit activity similar to that of sucrose. The changes in adsorbed protein mass can be attributed to a decreased packing density of the proteins in the adsorbed layers. Moreover, we investigated insulin adsorption at a hydrophobic surface in the absence and presence of glycerol. The degree of insulin adsorption is decreased by even 80% in the presence of 4 M of glycerol. The results of this study demonstrate that nonionic cosolvents can be used to tune and control nonspecific protein adsorption at aqueous-solid interfaces, which might be relevant for biomedical applications.

  15. Metal adsorption on mosses: Toward a universal adsorption model.

    PubMed

    González, A G; Pokrovsky, O S

    2014-02-01

    This study quantifies the adsorption of heavy metals on 4 typical moss species used for environmental monitoring in the moss bag technique. The adsorption of Cu(2+), Cd(2+), Ni(2+), Pb(2+) and Zn(2+) onto Hypnum sp., Sphagnum sp., Pseudoscleropodium purum and Brachytecium rutabulum has been investigated using a batch reactor in a wide range of pH (1.3-11.0) and metal concentrations in solution (1.6μM-3.8mM). A Linear Programming Model (LPM) was applied for the experimental data to derive equilibrium constants and the number of surface binding sites. The surface acid-base titration performed for 4 mosses at a pH range of 3-10 in 0.1M NaNO3 demonstrated that Sphagnum sp. is the most efficient adsorbent as it has the maximal number of proton-binding sites on the surface (0.65mmol g(-1)). The pKa computed for all the moss species suggested the presence of 5 major functional groups: phosphodiester, carboxyl, phosphoryl, amine and polyphenols. The results of pH-edge experiments demonstrated that B. rutabulum exhibits the highest percentage of metal adsorption and has the highest number of available sites for most of the metals studied. However, according to the results of the constant pH "Langmuirian" isotherm, Sphagnum sp. can be considered as the strongest adsorbent, although the relative difference from other mosses is within 20%. The LPM was found to satisfactorily fit the experimental data in the full range of the studied solution parameters. The results of this study demonstrate a rather similar pattern of five metal adsorptions on mosses, both as a function of pH and as a metal concentration, which is further corroborated by similar values of adsorption constants. Therefore, despite the species and geographic differences between the mosses, a universal adsorption edge and constant pH adsorption isotherm can be recommended for 4 studied mosses. The quantitative comparison of metal adsorption with other common natural organic and inorganic materials demonstrates

  16. REVIEW ARTICLE: The transmission interferometric adsorption sensor

    NASA Astrophysics Data System (ADS)

    Heuberger, M.; Balmer, T. E.

    2007-12-01

    This paper describes a high-speed adsorption sensor based on thin-film interference at the interfaces. The sensor can be used as a stand-alone instrument or in combination with a direct surface force measurement, which yields a wide range of additional information on molecular interactions on adsorbed films. The achieved mass resolution of the presented method (1-10 ng cm-2 Hz-1/2) is comparable to or better than other modern bio-sensors. The dependence of mass resolution on various factors is presented and demonstrated in a number of relevant examples. The described method is suitable for the implementation of a low-cost bio-sensor with a minimal number of optical elements. The measurement spot size is one micrometre or more and sampling rates >10 Hz are readily possible. In contrast to other bio-sensors, the signal baseline has a remarkable long-term stability since the measured signal is virtually independent of refractive index changes in the fluid medium above the sensor surface. In combination with an optical spectral correlation method, the classical computer calculations are substituted by an optical calculator and a label-free real-time imaging adsorption sensor is realized. We demonstrate sensor operation both inside the extended surface forces apparatus as well as in a stand-alone bio-sensor configuration. As a final point, we illustrate the imaging capability of this new sensor technology on a patterned bio-functionalized surface.

  17. Influence of clay mineral structure and surfactant nature on the adsorption capacity of surfactants by clays.

    PubMed

    Sánchez-Martín, M J; Dorado, M C; del Hoyo, C; Rodríguez-Cruz, M S

    2008-01-15

    Adsorption of three surfactants of different nature, Triton X-100 (TX100) (non-ionic), sodium dodecylsulphate (SDS) (anionic) and octadecyltrimethylammonium bromide (ODTMA) (cationic) by four layered (montmorillonite, illite, muscovite and kaolinite) and two non-layered (sepiolite and palygorskite) clay minerals was studied. The objective was to improve the understanding of surfactant behaviour in soils for the possible use of these compounds in remediation technologies of contaminated soils by toxic organic compounds. Adsorption isotherms were obtained using surfactant concentrations higher and lower than the critical micelle concentration (cmc). These isotherms showed different adsorption stages of the surfactants by the clay minerals, and were classified in different subgroups of the L-, S- or H-types. An increase in the adsorption of SDS and ODTMA by all clay minerals is observed up to the cmc of the surfactant in the equilibrium solution is reached. However, there was further TX100 adsorption when the equilibrium concentration was well above the cmc. Adsorption constants from Langmuir and Freundlich equations (TX100 and ODTMA) or Freundlich equation (SDS) were used to compare adsorption of different surfactants by clay minerals studied. These constants indicated the surfactant adsorption by clay minerals followed this order ODTMA>TX100>SDS. The adsorption of TX100 and ODTMA was higher by montmorillonite and illite, and the adsorption of SDS was found to be higher by kaolinite and sepiolite. Results obtained show the influence of clay mineral structure and surfactant nature on the adsorption capacity of surfactants by clays, and they indicate the interest to consider the soil mineralogical composition when one surfactant have to be selected in order to establish more efficient strategies for the remediation of soils and water contaminated by toxic organic pollutants.

  18. FENTON-DRIVEN REGENERATION OF GRANULAR ACTIVATED CARBON: A TECHNOLOGY OVERVIEW

    EPA Science Inventory

    A Fenton-driven mechanism for regenerating spent granular activated carbon (GAC) involves the combined, synergistic use of two reliable and well established treatment technologies - adsorption onto activated carbon and Fenton oxidation. During carbon adsorption treatment, enviro...

  19. Overview of the Performance and Cost Effectiveness of Small Arsenic Removal Technologies

    EPA Science Inventory

    Presentation provides information on the performance and cost of primarily four arsenic removal technologies; adsorptive media, iron removal, coagulation/filtration and the combination system of iron removal followed by adsorptive media.

  20. Adsorption isotherms of charged nanoparticles.

    PubMed

    Dos Santos, Alexandre P; Bakhshandeh, Amin; Diehl, Alexandre; Levin, Yan

    2016-10-19

    We present theory and simulations which allow us to quantitatively calculate the amount of surface adsorption excess of charged nanoparticles onto a charged surface. The theory is very accurate for weakly charged nanoparticles and can be used at physiological concentrations of salt. We have also developed an efficient simulation algorithm which can be used for dilute suspensions of nanoparticles of any charge, even at very large salt concentrations. With the help of the new simulation method, we are able to efficiently calculate the adsorption isotherms of highly charged nanoparticles in suspensions containing multivalent ions, for which there are no accurate theoretical methods available.

  1. Thermodynamic features of dioxins' adsorption.

    PubMed

    Prisciandaro, Marina; Piemonte, Vincenzo; di Celso, Giuseppe Mazziotti; Ronconi, Silvia; Capocelli, Mauro

    2017-02-15

    In this paper, the six more poisonous species among all congeners of dioxin group are taken into account, and the P-T diagram for each of them is developed. Starting from the knowledge of vapour tensions and thermodynamic parameters, the theoretical adsorption isotherms are calculated according to the Langmuir's model. In particular, the Langmuir isotherm parameters (K and wmax) have been validated through the estimation of the adsorption heat (ΔHads), which varies in the range 20-24kJ/mol, in agreement with literature values. This result will allow to put the thermodynamical basis for a rational design of different process units devoted to dioxins removal.

  2. Counterion release and electrostatic adsorption

    PubMed

    Sens; Joanny

    2000-05-22

    The effective charge of a rigid polyelectrolyte (PE) approaching an oppositely charged surface is studied. The cases of a weak (annealed) and strongly charged PE with condensed counterions (such as DNA) are discussed. In the most interesting case of the adsorption onto a substrate of low dielectric constant (such as a lipid membrane or a mica sheet) the condensed counterions are not always released as the PE approaches the substrate, because of the major importance of the image-charge effect. For the adsorption onto a surface with freely moving charges, the image-charge effect becomes less important and full release is often expected.

  3. Equilibrium and heat of adsorption for organic vapors and activated carbons

    SciTech Connect

    David Ramirez; Shaoying Qi; Mark J. Rood; K. James Hay

    2005-08-01

    Determination of the adsorption properties of novel activated carbons is important to develop new air quality control technologies that can solve air quality problems in a more environmentally sustainable manner. Equilibrium adsorption capacities and heats of adsorption are important parameters for process analysis and design. Experimental adsorption isotherms were thus obtained for relevant organic vapors with activated carbon fiber cloth (ACFC) and coal-derived activated carbon adsorbents (CDAC). The Dubinin-Astakhov (DA) equation was used to describe the adsorption isotherms. The DA parameters were analytically and experimentally shown to be temperature independent. The resulting DA equations were used with the Clausius-Clapeyron equation to analytically determine the isosteric heat of adsorption ({Delta}H{sub s}) of the adsorbate-adsorbent systems studied here. ACFC showed higher adsorption capacities for organic vapors than CDAC. {Delta}H{sub s} values for the adsorbates were independent of the temperature for the conditions evaluated. {Delta}H{sub s} values for acetone and benzene obtained in this study are comparable with values reported in the literature. This is the first time that {Delta}H{sub s} values for organic vapors and these adsorbents are evaluated with an expression based on the Polanyi adsorption potential and the Clausius-Clapeyron equation. 28 refs., 5 figs., 5 tabs., 3 appends.

  4. Effects of Cabin Upsets on Adsorption Columns for Air Revitalization

    NASA Technical Reports Server (NTRS)

    LeVan, M. Douglas

    1999-01-01

    The National Aeronautics and Space Administration (NASA) utilizes adsorption technology as part of contaminant removal systems designed for long term missions. A variety of trace contaminants can be effectively removed from gas streams by adsorption onto activated carbon. An activated carbon adsorption column meets NASA's requirements of a lightweight and efficient means of controlling trace contaminant levels aboard spacecraft and space stations. The activated carbon bed is part of the Trace Contaminant Control System (TCCS) which is utilized to purify the cabin atmosphere. TCCS designs oversize the adsorption columns to account for irregular fluctuations in cabin atmospheric conditions. Variations in the cabin atmosphere include changes in contaminant concentrations, temperature, and relative humidity. Excessively large deviations from typical conditions can result from unusual crew activity, equipment malfunctions, or even fires. The research carried out under this award focussed in detail on the effects of cabin upsets on the performance of activated carbon adsorption columns. Both experiments and modeling were performed with an emphasis on the roll of a change in relative humidity on adsorption of trace contaminants. A flow through fixed-bed apparatus was constructed at the NASA Ames Research Center, and experiments were performed there by W. Scot Appel under the direction of Dr. John E. Finn. Modeling work was performed at the University of Virginia and at Vanderbilt University by W. Scot Appel under the direction of M. Douglas LeVan. All three participants collaborated in all of the various phases of the research. The most comprehensive document describing the research is the Ph.D. dissertation of W. Scot Appel. Results have been published in several papers and presented in talks at technical conferences. All documents have been transmitted to Dr. John E. Finn.

  5. Adsorption of Organics from Domestic Water Supplies.

    ERIC Educational Resources Information Center

    McGuire, Michael J.; Suffet, Irwin H.

    1978-01-01

    This article discusses the current state of the art of organics removal by adsorption. Various theoretical explanations of the adsorption process are given, along with practical results from laboratory, pilot-scale, and full-scale applications. (CS)

  6. CONTAMINANT ADSORPTION AND OXIDATION VIA FENTON REACTION

    EPA Science Inventory

    A ground water treatment process is proposed involving two cgemical processes: adsorption and oxidation. Adsorption of an organic compound onto granulated activated carbon (GAC) containing iron conveniently results in immobilizing and concentrating contaminants from the ground w...

  7. Adsorption of selected emerging contaminants onto PAC and GAC: Equilibrium isotherms, kinetics, and effect of the water matrix.

    PubMed

    Real, Francisco J; Benitez, F Javier; Acero, Juan L; Casas, Francisco

    2017-03-30

    The removal of three emerging contaminants (ECs) (amitriptyline hydrochloride (AH), methyl salicylate (MS) and 2-phenoxyethanol (PE)) dissolved in several water matrices by means of their adsorption onto powdered activated carbon (PAC) and granular activated carbon (GAC) has been investigated. When dissolved in ultrapure water, adsorption of the ECs followed the trend of AH > MS > PE, with a positive effect of the adsorbent dose. According to the analysis of the adsorption isotherms and adsorption kinetics, PAC showed strongly higher adsorption efficiency in both capacity and velocity of the adsorption, in agreement with its higher mesoporosity. Equilibrium isotherm data were fitted by Langmuir and Freundlich models. Pseudo-second order kinetics modeled very successfully the adsorption process. Finally, the effect of the presence of dissolved organic matter (DOM) in the water matrices (ultrapure water, surface water and two effluents from wastewater treatment plants) on the adsorption of the selected ECs onto PAC was established, as well as its performance on the removal of water quality parameters. Results show a negative effect of the DOM content on the adsorption efficiency. Over 50% of organic matter was removed with high PAC doses, revealing that adsorption onto PAC is an effective technology to remove both micro-pollutants and DOM from water matrices.

  8. ADSORPTION OF SURFACTANT ON CLAYS

    EPA Science Inventory

    Surfactants used to enhance remediation of soils by soil washing are often lost in the process. Neither the amount nor the cause of this loss is known. It is assumed that clays present in the soil are responsible for the loss of the surfactant. In this papere, adsorption prope...

  9. Adsorption of pesticides on resins.

    PubMed

    Kyriakopoulos, Grigorios; Hourdakis, Adamadia; Doulia, Danae

    2003-03-01

    The objective of this work was to assess the capability of organic hydrophobic polymeric resins Amberlite XAD-4 and XAD-7 to remove the pesticides alachlor and amitrole from water. The pesticides adsorption on the two different adsorbents was measured by batch equilibrium technique and isotherm types and parameters were estimated. Two theoretical models were applied based on a Freundlich and a Langmuir isotherms. The effect of pesticides chemical composition and structure as well as the nature of solid surface on the efficiency of adsorption was evaluated. The influence of pH also was studied. In low pH solutions adsorption of amitrole was higher upon the nonionic aliphatic acrylic ester copolymer XAD-7 in comparison to the nonionic, crosslinked macroreticular copolymer of styrene divinylbenzene XAD-4. In neutral and intermediate pH solutions the polar acrylic ester copolymer XAD-7 was more effective to the retention of alachlor. The acrylic ester copolymer showed at pH 3 the lower effectiveness in alachlor removal from water. The data of the adsorption isotherms of pesticides upon the examined polymeric resins seemed to conform to both the Freundlich and the Langmuir isotherm models.

  10. Engineering and Design: Adsorption Design Guide

    DTIC Science & Technology

    2001-03-01

    adsorptive media addressed in- clude granular activated carbon (GAC) and other alternative adsorption carbon media, such as powdered activated carbon (PAC... Adsorption Media. a. Activated Carbon . Activated carbon can be manufactured from carbonaceous material, in- cluding coal (bituminous, subbituminous...information contained in Corps of Engineers Guide Specification 11225: Downflow Liquid Granular Activated Carbon

  11. Adsorptive removal of antibiotics from water and wastewater: Progress and challenges.

    PubMed

    Ahmed, Mohammad Boshir; Zhou, John L; Ngo, Huu Hao; Guo, Wenshan

    2015-11-01

    Antibiotics as emerging contaminants are of global concern due to the development of antibiotic resistant genes potentially causing superbugs. Current wastewater treatment technology cannot sufficiently remove antibiotics from sewage, hence new and low-cost technology is needed. Adsorptive materials have been extensively used for the conditioning, remediation and removal of inorganic and organic hazardous materials, although their application for removing antibiotics has been reported for ~30 out of 250 antibiotics so far. The literature on the adsorptive removal of antibiotics using different adsorptive materials is summarized and critically reviewed, by comparing different adsorbents with varying physicochemical characteristics. The efficiency for removing antibiotics from water and wastewater by different adsorbents has been evaluated by examining their adsorption coefficient (Kd) values. For sulfamethoxazole the different adsorbents followed the trend: biochar (BC)> multi-walled carbon nanotubes (MWCNTs)>graphite = clay minerals, and for tetracycline the adsorptive materials followed the trend: SWCNT > graphite > MWCNT = activated carbon (AC) > bentonite = humic substance = clay minerals. The underlying controlling parameters for the adsorption technology have been examined. In addition, the cost of preparing adsorbents has been estimated, which followed the order of BCs < ACs < ion exchange resins < MWCNTs < SWCNTs. The future research challenges on process integration, production and modification of low-cost adsorbents are elaborated.

  12. Simulation of methane adsorption on A-zeolites

    NASA Astrophysics Data System (ADS)

    Woestyn, A. M.; Mentasty, L.; Riccardo, J. L.; Zgrablich, G.

    1996-07-01

    A Monte Carlo simulation has been performed to study adsorption of CH4 on zeolites and the result are here presented for NaA and CaNaA zeolites. The adsorption isotherms of CH4 and the radial distribution of the adsorbed molecules have been obtained at four different temperatures in the pressure range 0 to 5 Mpa. The potential energy of adsorption has been calculated and the energy profile of a CH4 molecule along different axes in the zeolite cavity are discussed. High density storage of natural gas is essential for the efficient use of this gas as an alternative transportation fuel. One of the promising storage technologies is the adsorbed natural gas (ANG), in which the gas is adsorbed on highly microporous solids like zeolites or actived carbons. Structural as well as chemical properties of the porous adsorbents influence strongly the adsorption phenomenon, therefore, both experimental as theorical investigation are still necessary to select better solids for specific applications.

  13. Simulation of methane adsorption on A-zeolites

    SciTech Connect

    Woestyn, A.M.; Mentasty, L.; Riccardo, J.L.; Zgrablich, G.

    1996-07-01

    A Monte Carlo simulation has been performed to study adsorption of CH{sub 4} on zeolites and the result are here presented for NaA and CaNaA zeolites. The adsorption isotherms of CH{sub 4} and the radial distribution of the adsorbed molecules have been obtained at four different temperatures in the pressure range 0 to 5 Mpa. The potential energy of adsorption has been calculated and the energy profile of a CH{sub 4} molecule along different axes in the zeolite cavity are discussed. High density storage of natural gas is essential for the efficient use of this gas as an alternative transportation fuel. One of the promising storage technologies is the adsorbed natural gas (ANG), in which the gas is adsorbed on highly microporous solids like zeolites or actived carbons. Structural as well as chemical properties of the porous adsorbents influence strongly the adsorption phenomenon, therefore, both experimental as theorical investigation are still necessary to select better solids for specific applications. {copyright} {ital 1996 American Institute of Physics.}

  14. Phosphate adsorption on lanthanum loaded biochar.

    PubMed

    Wang, Zhanghong; Shen, Dekui; Shen, Fei; Li, Tianyu

    2016-05-01

    To attain a low-cost and high-efficient phosphate adsorbent, lanthanum (La) loaded biochar (La-BC) prepared by a chemical precipitation method was developed. La-BC and its pristine biochar (CK-BC) were comparatively characterized using zeta potential, BET surface area, scanning electron microscopy/energy dispersive spectrometer (SEM-EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FT-IR). The adsorption ability and the mechanisms during adsorption process for the La-BC samples were also investigated. La loaded on the surface of biochar can be termed as La-composites (such as LaOOH, LaONO3 and La(OH)3), leading to the decrease of negative charge and surface area of biochar. La-BC exhibited the high adsorption capacity to phosphate compared to CK-BC. Adsorption isotherm and adsorption kinetic studies showed that the Langmuir isotherm and second order model could well describe the adsorption process of La-BC, indicating that the adsorption was dominated by a homogeneous and chemical process. The calculated maximum adsorption capacity was as high as 46.37 mg g(-1) (computed in P). Thermodynamic analysis revealed that the adsorption was spontaneous and endothermic. SEM, XRD, XPS and FT-IR analysis suggested that the multi-adsorption mechanisms including precipitation, ligand exchange and complexation interactions can be evidenced during the phosphate adsorption process by La-composites in La-BC.

  15. Adsorption of organic chemicals in soils.

    PubMed Central

    Calvet, R

    1989-01-01

    This paper presents a review on adsorption of organic chemicals on soils sediments and their constituents. The first part of this review deals with adsorption from gas and liquid phases and gives a discussion on the physical meaning of the shape of adsorption isotherms. Results show that no general rules can be proposed to describe univocally the relation between the shape of isotherms and the nature of adsorbate-adsorbent system. Kinetics of adsorption is discussed through the description of various models. Theoretical developments exist both for the thermodynamics and the kinetics of adsorption, but there is a strong need for experimental results. Possible adsorption mechanisms are ion exchange, interaction with metallic cations, hydrogen bonds, charge transfers, and London-van der Waals dispersion forces/hydrophobic effect. However, direct proofs of a given mechanism are rare. Several factors influence adsorption behavior. Electronic structure of adsorbed molecules, properties of adsorbents, and characteristics of the liquid phase are discussed in relation to adsorption. Such properties as water solubility, organic carbon content of adsorbing materials, and the composition of the liquid phase are particularly important. Evaluation of adsorption can be obtained through either laboratory measurements or use of several correlations. Adsorption measurements must be interpreted, taking into account treatment of adsorbent materials, experimental conditions, and secondary phenomena such as degradations. Correlations between adsorption coefficients and water-octanol partition coefficient or water solubility are numerous. They may be useful tools for prediction purposes. Relations with transport, bioavailability, and degradation are described. PMID:2695323

  16. Adsorption Behavior of Nonplanar Phthalocyanines: Competition of Different Adsorption Conformations

    PubMed Central

    2016-01-01

    Using density functional theory augmented with state-of-the-art van der Waals corrections, we studied the geometric and electronic properties of nonplanar chlorogallium-phthalocyanine GaClPc molecules adsorbed on Cu(111). Comparing these results with published experimental data for adsorption heights, we found indications for breaking of the metal–halogen bond when the molecule is heated during or after the deposition process. Interestingly, the work-function change induced by this dissociated geometry is the same as that computed for an intact adsorbate layer in the “Cl-down” configuration, with both agreeing well with the experimental photoemission data. This is unexpected, as the chemical natures of the adsorbates and the adsorption distances are markedly different in the two cases. The observation is explained as a consequence of Fermi-level pinning due to fractional charge transfer at the interface. Our results show that rationalizing the adsorption configurations on the basis of electronic interface properties alone can be ambiguous and that additional insight from dispersion-corrected DFT simulations is desirable. PMID:27066160

  17. Investigation of Microgranular Adsorptive Filtration System

    NASA Astrophysics Data System (ADS)

    Cai, Zhenxiao

    Over the past few decades, enormous advances have been made in the application of low-pressure membrane filtration to both drinking water and wastewater treatment. Nevertheless, the full potential of this technology has not been reached, due primarily to limitations imposed by membrane fouling. In drinking water treatment, much of the fouling is caused by soluble and particulate natural organic matter (NOM). Efforts to overcome the problem have focused on removal of NOM from the feed solution, usually by addition of conventional coagulants like alum and ferric chloride (FeCl3) or adsorbents like powdered activated carbon (PAC). While coagulants and adsorbents can remove a portion of the NOM, their performance with respect to fouling control has been inconsistent, often reducing fouling but sometimes having no effect or even exacerbating fouling. This research investigated microgranular adsorptive filtration (muGAF), a process that combines three existing technologies---granular media filtration, packed bed adsorption, and membrane filtration---in a novel way to reduce membrane fouling while simultaneously removing NOM from water. In this technology, a thin layer of micron-sized adsorbent particles is deposited on the membrane prior to delivering the feed to the system. The research reported here represents the first systematic study of muGAF, and the results demonstrate the promising potential of this process. A new, aluminum-oxide-based adsorbent---heated aluminum oxide particles (HAOPs)---was synthesized and shown to be very effective for NOM removal as well as fouling reduction in muGAF systems. muGAF has also been demonstrated to work well with powdered activated carbon (PAC) as the adsorbent, but not as well as when HAOPs are used; the process has also been successful when used with several different membrane types and configurations. Experiments using a wide range of operational parameters and several analytical tools lead to the conclusion that the fouling

  18. Studies on Vapor Adsorption Systems

    NASA Technical Reports Server (NTRS)

    Shamsundar, N.; Ramotowski, M.

    1998-01-01

    The project consisted of performing experiments on single and dual bed vapor adsorption systems, thermodynamic cycle optimization, and thermal modeling. The work was described in a technical paper that appeared in conference proceedings and a Master's thesis, which were previously submitted to NASA. The present report describes some additional thermal modeling work done subsequently, and includes listings of computer codes developed during the project. Recommendations for future work are provided.

  19. Biosynthesis of bifunctional iron oxyhydrosulfate by Acidithiobacillus ferroxidans and their application to coagulation and adsorption.

    PubMed

    Gan, Min; Song, Zibo; Jie, Shiqi; Zhu, Jianyu; Zhu, Yaowu; Liu, Xinxing

    2016-02-01

    Coagulation and adsorption are important environmental technologies, which were widely applied in water treatment. In this study, a type of villous iron oxyhydrosulfate with low crystallinity, high content iron, sulfate and hydroxyl was synthesized by Acidithiobacillus ferrooxidans, which possessed coagulation and heavy metal adsorption ability simultaneously. The results showed that the Cu(II) adsorption capacity increased within a small range over the pH range of 3.0-5.0 but increased evidently over the range of 6.0-8.0. The maximal Cu(II) adsorption capacity of sample Af and Gf reached 50.97 and 46.08mg/g respectively. The optimum pH for Cr(VI) adsorption was 6.0, and the maximal adsorption capacity reached 51.32 and 59.57mg/g. The Langmuir isotherm can better describe the adsorption behavior of Cr(VI). Coagulation performance of the iron oxyhydrosulfate (Sh) has been significantly enhanced by polysilicic acid (PSA), which was mainly determined by PSA/Sh ratio, pH and coagulant dosage. Coagulation efficiency maintained approximately at 98% when the PSA/Sh ratio ranged from 0.4/0.1 to 1.0/0.1. Polysilicic acid worked efficiently in wide pH range extending, from 2 to 3.5. Coagulation performance improved significantly with the increasing of the coagulant dosage at lower dosage range, while, at higher dosage range, the improvement was not evident even with more coagulant addition.

  20. Thermodynamic modeling of solute adsorption equilibrium from near-critical carbon dioxide.

    PubMed

    Yang, Xiaoning

    2004-05-15

    Modeling of adsorption equilibrium for supercritical fluid mixtures, with as few parameters as possible, is important in applications of the technology of supercritical fluid adsorption. In this paper, a correlative model has been developed to represent the adsorption equilibria of solutes from the near-critical CO(2) fluid. A two-dimensional van der Waals equation of state and the three-dimensional P - R equation of state were used to describe the adsorbed and bulk phases, respectively. This model contains five parameters for adsorption equilibrium isotherms at finite concentrations and two parameters for adsorption equilibrium constants at infinite dilution. All the parameters are independent of temperature and pressure. By applying the model to the experimental data from the literature, it was shown that this model is capable of describing the adsorption behavior of solutes from supercritical carbon dioxide over relatively wide temperature and pressure ranges. In addition, the adsorption behavior of supercritical fluid mixtures was investigated at finite and infinite dilution conditions.

  1. Methane adsorption in nanoporous carbon: the numerical estimation of optimal storage conditions

    NASA Astrophysics Data System (ADS)

    Ortiz, L.; Kuchta, B.; Firlej, L.; Roth, M. W.; Wexler, C.

    2016-05-01

    The efficient storage and transportation of natural gas is one of the most important enabling technologies for use in energy applications. Adsorption in porous systems, which will allow the transportation of high-density fuel under low pressure, is one of the possible solutions. We present and discuss extensive grand canonical Monte Carlo (GCMC) simulation results of the adsorption of methane into slit-shaped graphitic pores of various widths (between 7 Å and 50 Å), and at pressures P between 0 bar and 360 bar. Our results shed light on the dependence of film structure on pore width and pressure. For large widths, we observe multi-layer adsorption at supercritical conditions, with excess amounts even at large distances from the pore walls originating from the attractive interaction exerted by a very high-density film in the first layer. We are also able to successfully model the experimental adsorption isotherms of heterogeneous activated carbon samples by means of an ensemble average of the pore widths, based exclusively on the pore-size distributions (PSD) calculated from subcritical nitrogen adsorption isotherms. Finally, we propose a new formula, based on the PSD ensemble averages, to calculate the isosteric heat of adsorption of heterogeneous systems from single-pore-width calculations. The methods proposed here will contribute to the rational design and optimization of future adsorption-based storage tanks.

  2. Hydrogen Adsorption in Carbon nanoparticles

    NASA Astrophysics Data System (ADS)

    Cabrera, A. L.; Rojas, S.; Dias-Droguett, D. E.; Bhuyan, H.; Aomoa, N.; Kakati, M.

    2013-03-01

    We have studied hydrogen adsorption in carbon nanoparticles using a quartz crystal microbalance. The carbon nanoparticles were synthesized from a thermal plasma jet at different pressure (15 - 263 torr) of the reactants and different current (50 - 250 A) to generate the plasma. The as-prepared carbon nanoparticles were directly deposited on top of the gold electrode of a quartz crystal and we monitored in-situ the changes in resonance frequency while the chamber was pressurized at different hydrogen pressures. These changes enabled determination of absorbed hydrogen mass in order to get H/C mass ratio curves as a function of H2 pressure. Adsorption curves obtained in some carbon nanoparticles indicated the formation of hydrogen monolayer inside the pores of the carbon nanoparticles. Using the value of the jump due to the formation of a H2\\ monolayer, a surface area was estimated between 40-60 m2/g for hydrogen adsorption. In other carbon samples, hydrogen uptake curves indicated that H2 was filling the sample's pores when pore volume was large. These observations will be discussed in detail for several carbon nanoparticles samples. Funds provided by VRI Puente 9/2012 and 10/2012

  3. Tritium Specific Adsorption Simulation Utilizing the OSPREY Model

    SciTech Connect

    Veronica Rutledge; Lawrence Tavlarides; Ronghong Lin; Austin Ladshaw

    2013-09-01

    During the processing of used nuclear fuel, volatile radionuclides will be discharged to the atmosphere if no recovery processes are in place to limit their release. The volatile radionuclides of concern are 3H, 14C, 85Kr, and 129I. Methods are being developed, via adsorption and absorption unit operations, to capture these radionuclides. It is necessary to model these unit operations to aid in the evaluation of technologies and in the future development of an advanced used nuclear fuel processing plant. A collaboration between Fuel Cycle Research and Development Offgas Sigma Team member INL and a NEUP grant including ORNL, Syracuse University, and Georgia Institute of Technology has been formed to develop off gas models and support off gas research. This report is discusses the development of a tritium specific adsorption model. Using the OSPREY model and integrating it with a fundamental level isotherm model developed under and experimental data provided by the NEUP grant, the tritium specific adsorption model was developed.

  4. Adsorption of Gemini surfactants onto clathrate hydrates.

    PubMed

    Salako, O; Lo, C; Couzis, A; Somasundaran, P; Lee, J W

    2013-12-15

    This work addresses the adsorption of two Gemini surfactants at the cyclopentane (CP) hydrate-water interface. The Gemini surfactants investigated here are Dowfax C6L and Dowfax 2A1 that have two anionic head groups and one hydrophobic tail group. The adsorption of these surfactants was quantified using adsorption isotherms and the adsorption isotherms were determined using liquid-liquid titrations. Even if the Gemini surfactant adsorption isotherms show multi-layer adsorption, they possess the first Langmuir layer with the second adsorption layer only evident in the 2A1 adsorption isotherm. Zeta potentials of CP hydrate particles in the surfactant solution of various concentrations of Dowfax C6L and Dowfax 2A1 were measured to further explain their adsorption behavior at the CP hydrate-water interface. Zeta potentials of alumina particles as a model particle system in different concentrations of sodium dodecyl sulfate (SDS), Dowfax C6L and Dowfax 2A1 were also measured to confirm the configuration of all the surfactants at the interface. The determination of the isotherms and zeta-potentials provides an understanding framework for the adsorption behavior of the two Gemini surfactants at the hydrate-water interface.

  5. Cell surface engineering of microorganisms towards adsorption of heavy metals.

    PubMed

    Li, Peng-Song; Tao, Hu-Chun

    2015-06-01

    Heavy metal contamination has become a worldwide environmental concern due to its toxicity, non-degradability and food-chain bioaccumulation. Conventional physical and chemical treatment methods for heavy metal removal have disadvantages such as cost-intensiveness, incomplete removal, secondary pollution and the lack of metal specificity. Microbial biomass-based biosorption is one of the approaches gaining increasing attention because it is effective, cheap, and environmental friendly and can work well at low concentrations. To enhance the adsorption properties of microbial cells to heavy metal ions, the cell surface display of various metal-binding proteins/peptides have been performed using a cell surface engineering approach. The surface engineering of Gram-negative bacteria, Gram-positive bacteria and yeast towards the adsorption of heavy metals are reviewed in this article. The problems and future perspectives of this technology are discussed.

  6. A COMPUTATIONAL AND EXPERIMENTAL STUDY OF METAL AND COVALENT ORGANIC FRAMEWORKS USED IN ADSORPTION COOLING

    SciTech Connect

    Jenks, Jeromy WJ; TeGrotenhuis, Ward E.; Motkuri, Radha K.; Paul, Brian; McGrail, B. Peter

    2015-07-09

    Metal-organic frameworks (MOFs) have recently attracted enormous interest over the past few years due to their potential applications in energy storage and gas separation. However, there have been few reports on MOFs for adsorption cooling applications. Adsorption cooling technology is an established alternative to mechanical vapor compression refrigeration systems. Adsorption cooling is an excellent alternative in industrial environments where waste heat is available. Applications also include hybrid systems, refrigeration, power-plant dry cooling, cryogenics, vehicular systems and building HVAC. Adsorption based cooling and refrigeration systems have several advantages including few moving parts and negligible power consumption. Key disadvantages include large thermal mass, bulkiness, complex controls, and low COP (0.2-0.5). We explored the use of metal organic frameworks that have very high mass loading and relatively low heats of adsorption, with certain combinations of refrigerants to demonstrate a new type of highly efficient adsorption chiller. An adsorption chiller based on MOFs suggests that a thermally-driven COP>1 may be possible with these materials, which would represent a fundamental breakthrough in performance of adsorption chiller technology. Computational fluid dynamics combined with a system level lumped-parameter model have been used to project size and performance for chillers with a cooling capacity ranging from a few kW to several thousand kW. In addition, a cost model has been developed to project manufactured cost of entire systems. These systems rely on stacked micro/mini-scale architectures to enhance heat and mass transfer. Presented herein are computational and experimental results for hydrophyilic MOFs, fluorophilic MOFs and also flourophilic Covalent-organic frameworks (COFs).

  7. DNA stickers promote polymer adsorption onto cellulose.

    PubMed

    Sato, Teruaki; Ali, Md Monsur; Pelton, Robert; Cranston, Emily D

    2012-10-08

    Adsorption of oligonucleotides onto model cellulose surfaces was investigated by comparing the Boese and Breaker's cellulose binding oligonucleotide (CBO) with a nonspecific oligonucleotide control (NSO). Measurements using the quartz crystal microbalance with dissipation technique confirmed that CBO adsorbed onto cellulose more than NSO, particularly at high ionic strengths (100 mM CaCl(2)). CBO showed a higher maximum adsorption on nanofibrillated and nanocrystalline cellulose than on regenerated cellulose, indicating a preference for the native cellulose I crystal structure under conditions that favored specific adsorption over calcium-mediated electrostatically driven adsorption. In addition, an anionic polyacrylamide (A-PAM) with grafted CBO also adsorbed onto the surface of cellulose in CaCl(2), whereas the unmodified A-PAM did not. This work shows that CBO performs as a "sticker", facilitating the adsorption of polyacrylamide onto cellulose, even under high ionic strength conditions where the adsorption of conventional polyelectrolytes is inhibited.

  8. Adsorption of goethite onto quartz and kaolinite

    USGS Publications Warehouse

    Goldberg, M.C.; Weiner, Eugene R.; Boymel, P.M.

    1984-01-01

    The adsorption of colloidal goethite onto quartz and kaolinite substrates has been studied as a function of pH and NaCl concentration. Goethite adsorption was measured quantitatively by Fourier-transform infrared spectroscopy. The results indicate that adsorption onto both substrates is due primarily to coulombic forces; however, the pH dependence of adsorption is very different for the two substrates. This is explained by the fact that the surface charge on quartz is entirely pH-dependent, while kaolinite has surface faces which carry a permanent negative charge. Adsorption of goethite on to kaolinite increases markedly with increasing NaCl concentration, while adsorption onto quartz is relatively independent of NaCl concentration. This can be explained by the influence of NaCl concentration upon the development of surface charge on the substrates. A method is described for separating surface-bound goethite from free goethite.

  9. Adsorption and isotopic fractionation of Xe

    NASA Technical Reports Server (NTRS)

    Bernatowicz, T. J.; Podosek, F. A.

    1986-01-01

    A theoretical description of the mechanisms of isotopic fractionation arising during adsorption of noble gases in a Henry's Law pressure regime is given. Experimental data on the isotopic composition of Xe adsorbed on activated charcoal in the temperature range 220 K to 350 K are presented. Both theoretical considerations and the experimental data indicate that equilibrium adsorption does not significantly alter the isotopic structure of adsorbed structure of adsorbed noble gases. Therefore, if adsorption is responsible for the elemental noble gas pattern in meteorites and the earth, the heavy noble gas isotopic fractionation between them must have been produced prior to and by a different process than equilibrium adsorption.

  10. Adsorption of water vapor on reservoir rocks

    SciTech Connect

    Not Available

    1993-07-01

    Progress is reported on: adsorption of water vapor on reservoir rocks; theoretical investigation of adsorption; estimation of adsorption parameters from transient experiments; transient adsorption experiment -- salinity and noncondensible gas effects; the physics of injection of water into, transport and storage of fluids within, and production of vapor from geothermal reservoirs; injection optimization at the Geysers Geothermal Field; a model to test multiwell data interpretation for heterogeneous reservoirs; earth tide effects on downhole pressure measurements; and a finite-difference model for free surface gravity drainage well test analysis.

  11. Adsorption of acid dye onto organobentonite.

    PubMed

    Baskaralingam, P; Pulikesi, M; Elango, D; Ramamurthi, V; Sivanesan, S

    2006-02-06

    Removal of Acid Red 151 from aqueous solution at different dye concentrations, adsorbent doses and pH has been studied. The bentonite clay has been modified using cationic surfactants, which has been confirmed using XRD and FT-IR analyses. Experimental result has shown that the acidic pH favours the adsorption. The adsorption isotherms are described by means of Langmuir and Freundlich isotherms. The adsorption capacity has been found to be 357.14 and 416.66 mg g(-1) for the cetyldimethylbenzylammonium chloride-bentonite (CDBA-bent) and cetylpyridinium chloride-bentonite (CP-bent), respectively. Kinetic studies show that the adsorption followed second-order kinetics.

  12. Ozone adsorption on carbon nanoparticles

    NASA Astrophysics Data System (ADS)

    Chassard, Guillaume; Gosselin, Sylvie; Visez, Nicolas; Petitprez, Denis

    2014-05-01

    Carbonaceous particles produced by incomplete combustion or thermal decomposition of hydrocarbons are ubiquitous in the atmosphere. On these particles are adsorbed hundreds of chemical species. Those of great concern to health are polycyclic aromatic hydrocarbons (PAHs). During atmospheric transport, particulate PAHs react with gaseous oxidants. The induced chemical transformations may change toxicity and hygroscopicity of these potentially inhalable particles. The interaction between ozone and carbon particles has been extensively investigated in literature. However ozone adsorption and surface reaction mechanisms are still ambiguous. Some studies described a fast catalytic decomposition of ozone initiated by an atomic oxygen chemisorption followed by a molecular oxygen release [1-3]. Others suggested a reversible ozone adsorption according to Langmuir-type behaviour [4,5]. The aim of this present study is a better understanding of ozone interaction with carbon surfaces. An aerosol of carbon nanoparticles was generated by flowing synthetic air in a glass tube containing pure carbon (primary particles < 50 nm), under magnetic stirring. The aerosol was then mixed with ozone in an aerosol flow tube. Ozone uptake experiments were performed with different particles concentrations with a fixed ozone concentration. The influence of several factors on kinetics was examined: initial ozone concentration, particle size (50 nm ≤ Dp ≤ 200 nm) and competitive adsorption (with probe molecule and water). The effect of initial ozone concentration was first studied. Accordingly to literature, it has been observed that the number of gas-phase ozone molecules lost per unit particle surface area tends towards a plateau for high ozone concentration suggesting a reversible ozone adsorption according to a Langmuir mechanism. We calculated the initial reaction probability between O3 and carbon particles.An initial uptake coefficient of 1.10-4 was obtained. Similar experiments were

  13. Anion adsorption induced surface reconstructions

    NASA Astrophysics Data System (ADS)

    Tang, Lei

    2005-11-01

    Surface stress plays an important role in the behavior of solid surfaces. Potential-controlled anion adsorption in electrolytes alters the surface stress of the electrode and results in morphology changes to the surfaces. With a combination of potential-induced surface stress measurement and in situ electrochemical scanning tunneling microscopy (STM), it is demonstrated that anion adsorption induces changes in structure of thin films and modifies the growth morphology and stress evolution in epitaxially grown films. Surface structural transitions in the heteroepitaxial system consisting of one to two gold monolayers on platinum substrates were observed. By increasing the potential, structural transitions, from (1 x 1), to a striped phase, to a hexagonal structure, occurred in the gold bilayer. This hexagonal structure was related to the formation of an ordered sulfate adlayer with a ( 3x7 ) structure. Such transitions were repeatable by cycling the potential. Furthermore, the transitions between various dislocation structures were affected by anion adsorption. The surface composition of the gold bilayer on Pt was measured by underpotential deposition of copper. By subtracting the contribution of a pure Pt surface from the gold bi-layer on Pt, a stress change of -2.4 N/m was observed, which agrees with the stress change of -2.46 N/m predicted to accompany formation of 1.5 MLs of coherent Au on Pt(111) from epitaxy theory. The Cu monolayer deposited on Au(111) from an acid sulfate electrolyte was found to be pseudomorphic while the Cu monolayer formed on Au(111) in vacuum was incoherent. The stress-thickness change associated with the coherent monolayer of copper on Au(111) in electrolyte was -0.6 N/m, while conventional epitaxy theories predict a value of +7.76 N/m. STM results elucidated the sulfate adsorption on the copper monolayer caused an expansion of the layer as evidenced by a Moire Structure. For the Cu monolayer on Au(111), the sulfate-induced expansion

  14. Charcoal/Nitrogen Adsorption Cryocooler

    NASA Technical Reports Server (NTRS)

    Bard, Steven

    1987-01-01

    Refrigerator with no wear-related moving parts produces 0.5 W of cooling at 118 K. When fully developed, refrigerator needs no electrical power, and life expectancy of more than 10 yr, operates unattended to cool sensitive infrared detectors for long periods. Only moving parts in adsorption cryocooler are check valves. As charcoal is cooled in canister, gas pressure drops, allowing inlet check valve to open and admit more nitrogen. When canister is heated, pressure rises, closing inlet valve and eventually opening outlet valve.

  15. Moisture adsorption in optical coatings

    NASA Technical Reports Server (NTRS)

    Macleod, H. Angus

    1988-01-01

    The thin film filter is a very large aperture component which is exceedingly useful because of its small size, flexibility and ease of mounting. Thin film components, however, do have defects of performance and especially of stability which can cause problems in systems, particularly where long-term measurements are being made. Of all of the problems, those associated with moisture absorption are the most serious. Moisture absorption occurs in the pore-shaped voids inherent in the columnar structure of the layers. Ion-assisted deposition is a promising technique for substantially reducing moisture adsorption effects in thin film structures.

  16. Hydrogen adsorption on functionalized nanoporous activated carbons.

    PubMed

    Zhao, X B; Xiao, B; Fletcher, A J; Thomas, K M

    2005-05-12

    There is considerable interest in hydrogen adsorption on carbon nanotubes and porous carbons as a method of storage for transport and related energy applications. This investigation has involved a systematic investigation of the role of functional groups and porous structure characteristics in determining the hydrogen adsorption characteristics of porous carbons. Suites of carbons were prepared with a wide range of nitrogen and oxygen contents and types of functional groups to investigate their effect on hydrogen adsorption. The porous structures of the carbons were characterized by nitrogen (77 K) and carbon dioxide (273 K) adsorption methods. Hydrogen adsorption isotherms were studied at 77 K and pressure up to 100 kPa. All the isotherms were Type I in the IUPAC classification scheme. Hydrogen isobars indicated that the adsorption of hydrogen is very temperature dependent with little or no hydrogen adsorption above 195 K. The isosteric enthalpies of adsorption at zero surface coverage were obtained using a virial equation, while the values at various surface coverages were obtained from the van't Hoff isochore. The values were in the range 3.9-5.2 kJ mol(-1) for the carbons studied. The thermodynamics of the adsorption process are discussed in relation to temperature limitations for hydrogen storage applications. The maximum amounts of hydrogen adsorbed correlated with the micropore volume obtained from extrapolation of the Dubinin-Radushkevich equation for carbon dioxide adsorption. Functional groups have a small detrimental effect on hydrogen adsorption, and this is related to decreased adsorbate-adsorbent and increased adsorbate-adsorbate interactions.

  17. Adsorptive removal of antibiotics from aqueous solution using carbon materials.

    PubMed

    Yu, Fei; Li, Yong; Han, Sheng; Ma, Jie

    2016-06-01

    Antibiotics, an important type of environmental contamination, have attracted many researchers to the study of their removal from aqueous solutions. Adsorption technology is a fast, efficient, and economical physicochemical method that is extensively used in wastewater treatment. From original activated carbon and carbon nanotubes to the latest graphene-based materials, carbon-based materials have been widely used as highly effective adsorbents for contaminant removal from aqueous solution because of their large specific surface area, high porosity, and high reaction activity. In this article, adsorption removal methods for four major types of antibiotic (tetracyclines, sulfonamides, macrolides, and quinolones) are reviewed. We also provide an overview of the application development of carbon materials as adsorbents for antibiotic removal from aqueous solution. The most promising works are discussed, and the main challenges in preparing high-performance adsorbents and the development tendency of adsorbents are also analyzed. This work provides theoretical guidance for subsequent research in the design and modification of carbon materials for applications in the adsorption removal of antibiotics from aqueous solution.

  18. Adsorption of beta blockers to environmental surfaces.

    PubMed

    Kibbey, Tohren C G; Paruchuri, Rajiv; Sabatini, David A; Chen, Lixia

    2007-08-01

    Beta-adrenergic blocking agents (beta blockers) are widely used pharmaceuticals which have been detected in the environment. Predicting the transport and ultimate fate of beta blockers in the environment requires understanding their adsorption to soils and sediments, something for which little information is currently available. The objective of this work was to examine the adsorption of three beta blockers, propranolol, metoprolol and nadolol, to a natural alluvial material, as well as to six minerals present as components of the alluvial material. Batch adsorption experiments indicate that, for most of the minerals studied, compound hydrophobicity is an important predictor of adsorption, with propranolol,the most hydrophobic compound studied, adsorbing to the greatest extent. Results further suggest that, for the minerals studied, electrostatic effects are not a good predictor of adsorption; adsorption extent was not well-predicted by either surface zeta potential or by the difference between experiment pH and point of zero charge, despite the cationic nature af the three beta blockers at experiment pH values. Experiments were conducted to examine the effect of an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), on adsorption. Results indicate that SDBS significantly increases the adsorption of propranolol to two different sorbents. This result is potentially important because surfactants such as SDBS are likely to be present in wastewater effluents with beta blockers and could influence their mobility in the environment.

  19. Polychelated cryogels: hemoglobin adsorption from human blood.

    PubMed

    Erol, Kadir

    2017-02-01

    The separation and purification methods are extremely important for the hemoglobin (Hb) which is a crucial biomolecule. The adsorption technique is popular among these methods and the cryogels have been used quite much due to their macropores and interconnected flow channels. In this study, the Hb adsorption onto the Cu(II) immobilized poly(2-hydroxyethyl methacrylate-glycidyl methacrylate), poly(HEMA-GMA)-Cu(II), cryogels was investigated under different conditions (pH, interaction time, initial Hb concentration, temperature and ionic strength) to optimize adsorption conditions. The swelling test, Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM), surface area (BET), elemental and ICP-OES analysis were performed for the characterization of cryogels. Polyethyleneimine (PEI) molecule was used as a Cu(II)-chelating ligand. The Hb adsorption capacity of cryogels was determined as 193.8 mg Hb/g cryogel. The isolation of Hb from human blood was also studied under optimum adsorption conditions determined and the Hb (124.5 mg/g cryogel) was isolated. The adsorption model was investigated in the light of Langmuir and Freundlich adsorption isotherm models and it was determined to be more appropriate to the Langmuir adsorption isotherm model.

  20. Arsenate adsorption by unsaturated alluvial sediments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Arsenate adsorption as a function of solution arsenic concentration and solution pH was investigated on five alluvial sediments from the Antelope Valley, Western Mojave Desert, California. Arsenate adsorption increased with increasing solution pH, exhibited a maximum around pH 4 to 5, and then decr...

  1. BSA adsorption on bimodal PEO brushes.

    PubMed

    Bosker, W T E; Iakovlev, P A; Norde, W; Cohen Stuart, M A

    2005-06-15

    BSA adsorption onto bimodal PEO brushes at a solid surface was measured using optical reflectometry. Bimodal brushes consist of long (N=770) and short (N=48) PEO chains and were prepared on PS surfaces, applying mixtures of PS(29)-PEO(48) and PS(37)-PEO(770) block copolymers and using the Langmuir-Blodgett technique. Pi-A isotherms of (mixtures of) the block copolymers were measured to establish the brush regime. The isotherms of PS(29)-PEO(48) show hysteresis between compression and expansion cycles, indicating aggregation of the PS(29)-PEO(48) upon compression. Mixtures of PS(29)-PEO(48) and PS(37)-PEO(770) demonstrate a similar hysteresis effect, which eventually vanishes when the ratio of PS(37)-PEO(770) to PS(29)-PEO(48) is increased. The adsorption of BSA was determined at brushes for which the grafting density of the long PEO chains was varied, while the total grafting density was kept constant. BSA adsorption onto monomodal PEO(48) and PEO(770) brushes was determined for comparison. The BSA adsorption behavior of the bimodal brushes is similar to the adsorption of BSA at PEO(770) monomodal brushes. The maximum of BSA adsorption at low grafting density of PEO(770) can be explained by ternary adsorption, implying an attraction between BSA and PEO. The contribution of primary adsorption to the total adsorbed amount is negligible.

  2. Ion Exchange and Adsorption of Inorganic Contaminants

    EPA Science Inventory

    In the first part of the chapter, the fundamentals of ion exchange and adsorption processes are explained, with the goal of demonstrating how these principles influence process design for inorganic contaminant removal. In the second part, ion exchange and adsorption processes th...

  3. Phosphoryl functionalized mesoporous silica for uranium adsorption

    NASA Astrophysics Data System (ADS)

    Xue, Guo; Yurun, Feng; Li, Ma; Dezhi, Gao; Jie, Jing; Jincheng, Yu; Haibin, Sun; Hongyu, Gong; Yujun, Zhang

    2017-04-01

    Phosphoryl functionalized mesoporous silica (TBP-SBA-15) was synthesized by modified mesoporous silica with γ-amino propyl triethoxy silane and tributyl phosphate. The obtained samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), small angle X-ray diffraction (SAXRD), thermo-gravimetric/differential thermalanalyzer (TG/DTA), N2 adsorption-desorption (BET) and Fourier transform infrared spectroscopy (FT-IR) techniques. Results showed that TBP-SBA-15 had large surface areas with ordered channel structure. Moreover, the effects of adsorption time, sorbent dose, solution pH, initial uranium concentration and temperature on the uranium adsorption behaviors were investigated. TBP-SBA-15 showed a high uranium adsorption capacity in a broad range of pH values. The U(VI) adsorption rate of TBP-SBA-15 was fast and nearly achieved completion in 10 min with the sorbent dose of 1 g/L. The U(VI) adsorption of TBP-SBA-15 followed the pseudo-second-order kinetic model and Freundlich isotherm model, indicating that the process was belonged to chemical adsorption. Furthermore, the thermodynamic parameters (ΔG0, ΔH0 and ΔS0) confirmed that the adsorption process was endothermic and spontaneous.

  4. Adsorption and desorption of dissolved organic matter by carbon nanotubes: Effects of solution chemistry.

    PubMed

    Engel, Maya; Chefetz, Benny

    2016-06-01

    Increasing use of carbon nanotubes (CNTs) has led to their introduction into the environment where they can interact with dissolved organic matter (DOM). This study focuses on solution chemistry effects on DOM adsorption/desorption processes by single-walled CNTs (SWCNTs). Our data show that DOM adsorption is controlled by the attachment of DOM molecules to the SWCNTs, and that the initial adsorption rate is dependent on solution parameters. Adsorbed amount of DOM at high ionic strength was limited, possibly due to alterations in SWCNT bundling. Desorption of DOM performed at low pH resulted in additional DOM adsorption, whereas at high pH, adsorbed DOM amount decreased. The extent of desorption conducted at increased ionic strength was dependent on pre-adsorbed DOM concentration: low DOM loading stimulated additional adsorption of DOM, whereas high DOM loading facilitated release of adsorbed DOM. Elevated ionic strength and increased adsorbed amount of DOM reduced the oxidation temperature of the SWCNTs, suggesting that changes in the assembly of the SWCNTs had occurred. Moreover, DOM-coated SWCNTs at increased ionic strength provided fewer sites for atrazine adsorption. This study enhances our understanding of DOM-SWCNT interactions in aqueous systems influenced by rapid changes in salinity, and facilitates potential use of SWCNTs in water-purification technologies.

  5. How Surface Heterogeneity Affects Protein Adsorption: Annealing of OTS Patterns and Albumin Adsorption Kinetics*

    PubMed Central

    Hodgkinson, Gerald N.; Hlady, Vladimir

    2009-01-01

    Fluorescence microscopy and intensity histogram analysis techniques were used to monitor spatially-resolved albumin adsorption kinetics to model heterogeneous surfaces on sub-μm scales. Several distinct protein subpopulations were resolved, each represented by a normal distribution of adsorption densities on the adsorbent surface. Histogram analyses provided dynamic information of mean adsorption density, spread in adsorption density, and surface area coverage for each distinct protein subpopulation. A simple adsorption model is proposed in which individual protein binding events are predicted by the summation of multiple protein's surface sub-site interactions with different binding energy sub-sites on adsorbent surfaces. This model is predictive of the albumin adsorption on the patterns produced by one step μ-contact printing (μCP) of octadecyltrichlorosilane (OTS) on glass but fails to describe adsorption once the same patterns are altered by a thermal annealing step. PMID:19746205

  6. Gas-phase adsorption in dealuminated natural clinoptilolite and liquid-phase adsorption in commercial DAY zeolite and modified ammonium Y zeolite

    NASA Astrophysics Data System (ADS)

    Costa Hernandez, Alba Nydia

    The adsorption of Carbon Dioxide (CO2) is a very important tool for the material characterization. On the other hand, in separation and recovery technology, the adsorption of the CO2 is important to reduce the concentration of this gas considered as one of the greenhouse gases. Natural zeolites, particularly clinoptilolite, are widely applied to eliminate some pollutants from the environment. One of the goals of this research is to study the structure, composition and morphology of one natural clinoptilolite dealuminated with ammonium hexafluorosilicate (AHFi) and with orthophosphoric acid (H3PO4). Each modified sample was characterized using X-ray Diffraction (XRD), Carbon Dioxide adsorption at 0° C, Thermogravimetric Analysis (TGA), and Scanning Electron Microscopy with Energy Dispersive X-Ray Analysis (SEM-EDAX). In addition, the surface chemistry of the modified clinoptilolites was analyzed with Diffuse Reflectance Fourier Transform Infrared Spectroscopy (DRIFTS). The adsorption measurements were also used to study of the interaction of CO2 molecule within the adsorption space of these modified clinoptilolites. It was concluded that one of the modified clinoptilolites, (CSW-HFSi-0.1M), showed a great quality as adsorbent and as catalytic comparable to commercial synthetic zeolites. As far as we know, the modification of clinoptilolite with HFSi to improve their adsorption properties had not been previously attempted. In the second part of this dissertation, the dynamic adsorption of three isomers of nitrophenols using as adsorbent a commercial DAY zeolite was investigated. Also, the dynamic adsorption of methanol in a less hydrophobic zeolite, Ammonium Y Zeolite was investigated. The obtained breakthrough curves showed that the commercial DAY zeolite could be a suitable adsorbent to the liquid-phase adsorption of the phenolic compounds. Notwithstanding the modified ammonium Y zeolite had a low Si/Al ratio (less hydrophobic) than commercial DAY zeolite; this

  7. Factors affecting drug adsorption on beta zeolites.

    PubMed

    Pasti, Luisa; Sarti, Elena; Cavazzini, Alberto; Marchetti, Nicola; Dondi, Francesco; Martucci, Annalisa

    2013-05-01

    The adsorption behaviour of three commonly used drugs, namely ketoprofen, hydrochlorothiazide and atenolol, from diluted aqueous solutions on beta zeolites with different SiO2/Al2O3 ratio (i.e. 25, 38 and 360) was investigated by changing the ionic strength and the pH, before and after thermal treatment of the adsorbents. The selective adsorption of drugs was confirmed by thermogravimetry and X-ray diffraction. The adsorption capacity of beta zeolites was strongly dependent on both the solution pH and the alumina content of the adsorbent. Such a remarkable difference was interpreted as a function of the interactions between drug molecules and zeolite surface functional groups. Atenolol was readily adsorbed on the less hydrophobic zeolite, under pH conditions in which electrostatic interactions were predominant. On the other hand, ketoprofen adsorption was mainly driven by hydrophobic interactions. For undissociated molecules the adsorption capability increased with the increase of hydrophobicity.

  8. Adsorption and desorption of reversible supramolecular polymers

    NASA Astrophysics Data System (ADS)

    Zweistra, Henk J. A.; Besseling, N. A. M.

    2006-08-01

    We report numerical mean-field results on the quasichemical level of approximation that describe adsorption of reversible supramolecular polymers at a flat interface. Emphasis is laid on the regime of strong adsorption from a dilute solution. There are two differences with respect to macromolecular polymer adsorption: (i) adsorption sets in at relatively high monomer concentrations of the surrounding solution, and (ii) the surface is filled within a much narrower concentration range. Contrary to macromolecular polymers, supramolecular polymers can therefore be desorbed by dilution of the equilibrium solution by solvent within an experimentally accessible concentration window. Based on simple thermodynamic arguments, we provide a quantitative explanation why supramolecular polymers adsorb at relatively high concentrations. Moreover, we discuss the (by comparison) narrow concentration window wherein filling of the surface occurs. This is attributed to the cooperative nature of supramolecular polymer adsorption. The degree of cooperativity is quantified by means of the Hill parameter n .

  9. Adsorption of xenon and krypton on shales

    NASA Technical Reports Server (NTRS)

    Podosek, F. A.; Bernatowicz, T. J.; Kramer, F. E.

    1981-01-01

    A method that uses a mass spectrometer as a manometer is employed in the measurement of Xe and Kr adsorption parameters on shales and related samples, where gas partial pressures were lower than 10 to the -11th atm, corresponding adsorption coverages are only small fractions of a monolayer, and Henry's Law behavior is expected and observed. Results show heats of adsorption in the 2-7 kcal/mol range, and Henry constants at 0-25 C of 1 cu cm STP/g per atmosphere are extrapolated. Although the adsorption properties obtained are variable by sample, the range obtained suggests that shales may be capable of an equilibrium adsorption with modern air high enough to account for a significant fraction of the atmospheric inventory of Xe, and perhaps even of Kr. This effect will nevertheless not account for the factor-of-25 defficiency of atmospheric Xe, in comparison with the planetary gas patterns observed in meteorites.

  10. USE OF QSPRS IN IMPROVING CARBON ADSORPTION MODELING OF EPA CONTAMINANT CANDIDATE COMPOUNDS

    EPA Science Inventory

    Activated carbon adsorption of EPA contaminant candidate list (CCL) compounds is under investigation as a treatment technology for contaminated drinking water. Historically, EPA, in support of drinking water regulations, has used a number of techniques to calculate field-scale c...

  11. Arsenic Removal - Adsorptive Media and Coagulation/Filtration Case Studies - Slides

    EPA Science Inventory

    This presentation provides information on the results of three case studies from USEPA arsenic demonstration program. The first case study presented is on the Rimrock, AZ project that used an adsorptive media technology (E33 media) to remove arsenic. The second case study is o...

  12. Advancing adsorption and membrane separation processes for the gigaton carbon capture challenge.

    PubMed

    Wilcox, Jennifer; Haghpanah, Reza; Rupp, Erik C; He, Jiajun; Lee, Kyoungjin

    2014-01-01

    Reducing CO2 in the atmosphere and preventing its release from point-source emitters, such as coal and natural gas-fired power plants, is a global challenge measured in gigatons. Capturing CO2 at this scale will require a portfolio of gas-separation technologies to be applied over a range of applications in which the gas mixtures and operating conditions will vary. Chemical scrubbing using absorption is the current state-of-the-art technology. Considerably less attention has been given to other gas-separation technologies, including adsorption and membranes. It will take a range of creative solutions to reduce CO2 at scale, thereby slowing global warming and minimizing its potential negative environmental impacts. This review focuses on the current challenges of adsorption and membrane-separation processes. Technological advancement of these processes will lead to reduced cost, which will enable subsequent adoption for practical scaled-up application.

  13. Adsorption of water vapor by poly(styrenesulfonic acid), sodium salt: isothermal and isobaric adsorption equilibria.

    PubMed

    Toribio, F; Bellat, J P; Nguyen, P H; Dupont, M

    2004-12-15

    Air conditioning and dehumidifying systems based on sorption on solids are of great interest, especially in humid climates, because they allow reduction of thermal loads and use of chlorofluorocarbons. Previous studies have shown that hydrophilic polymers such as sulfonic polymers can have very high performance in water adsorption from air. The aim of this study was to characterize the water vapor adsorption properties of fully sulfonated and monosulfonated poly(styrenesulfonic acid), sodium salt, and to elucidate the mechanism of adsorption on these materials. Adsorption isotherms have been determined by TGA between 298 and 317 K for pressures ranging from 0.1 to 45 hPa. They have type II of the IUPAC classification and a small hysteresis loop between adsorption and desorption processes was observed only for the monosulfonated sample. Water content is up to 80% weight at 80% relative humidity. Adsorption isotherms have been well fitted with the FHH model. Adsorption-desorption isobars have been determined by TGA under 37 hPa in the temperature range 298-373 K. They show that these polymers can be completely regenerated by heating at 313 K under humidified air. No degradation of the adsorption properties has been observed after several regenerations. Adsorption enthalpies and entropies have been deduced from the Clapeyron equation and from DSC measurements. A good agreement was found. A mechanism of adsorption is proposed considering two kinds of adsorbate: bounded water in electrostatic interaction with functional groups and free water resulting from condensation.

  14. Modeling the adsorption of mixed gases based on pure gas adsorption properties

    NASA Astrophysics Data System (ADS)

    Tzabar, N.; Holland, H. J.; Vermeer, C. H.; ter Brake, H. J. M.

    2015-12-01

    Sorption-based Joule-Thomson (JT) cryocoolers usually operate with pure gases. A sorption-based compressor has many benefits; however, it is limited by the pressure ratios it can provide. Using a mixed-refrigerant (MR) instead of a pure refrigerant in JT cryocoolers allows working at much lower pressure ratios. Therefore, it is attractive using MRs in sorption- based cryocoolers in order to reduce one of its main limitations. The adsorption of mixed gases is usually investigated under steady-state conditions, mainly for storage and separation processes. However, the process in a sorption compressor goes through various temperatures, pressures and adsorption concentrations; therefore, it differs from the common mixed gases adsorption applications. In order to simulate the sorption process in a compressor a numerical analysis for mixed gases is developed, based on pure gas adsorption characteristics. The pure gas adsorption properties have been measured for four gases (nitrogen, methane, ethane, and propane) with Norit-RB2 activated carbon. A single adsorption model is desired to describe the adsorption of all four gases. This model is further developed to a mixed-gas adsorption model. In future work more adsorbents will be tested using these four gases and the adsorption model will be verified against experimental results of mixed-gas adsorption measurements.

  15. Arsenic Adsorption Equilibrium Concentration and Adsorption Rate of Activated Carbon Coated with Ferric-Aluminum Hydroxides

    NASA Astrophysics Data System (ADS)

    Zhang, M.; Sugita, H.; Oguma, T.; Hara, J.; Takahashi, S.

    2015-12-01

    In some areas of developing countries, ground or well water contaminated with arsenic has been reluctantly used as drinking water. It is highly desirable that effective and inexpensive arsenic removal agents should be developed and provided to reduce the potential health risk. Previous studies demonstrated that activated carbon coated with ferric-aluminum hydroxides (Fe-Al-C) has high adsorptive potential for removal of arsenic. In this study, a series of experiments using Fe-Al-C were carried to discuss adsorption equilibrium time, adsorption equilibrium concentration and adsorption rate of arsenic for Fe-Al-C. Fe-Al-C used in this study was provided by Astec Co., Ltd. Powder reagent of disodium hydrogen arsenate heptahydrate was dissolved into ion-exchanged water. The solution was then further diluted with ion-exchanged water to be 1 and 10 mg/L as arsenic concentration. The pH of the solution was adjusted to be around 7 by adding HCl and/or NaOH. The solution was used as artificial arsenic contaminated water in two types of experiments (arsenic adsorption equilibrium and arsenic adsorption rate tests). The results of the arsenic equilibrium tests were showed that a time period of about 3 days to reach apparent adsorption equilibrium for arsenic. The apparent adsorption equilibrium concentration and adsorbed amount of arsenic on Fe-Al-C adsorbent could be estimated by application of various adsorption isotherms, but the distribution coefficient of arsenic between solid and liquid varies with experimental conditions such as initial concentration of arsenic and addition concentration of adsorbent. An adsorption rate equation that takes into account the reduction in the number of effective adsorption sites on the adsorbent caused by the arsenic adsorption reaction was derived based on the data obtained from the arsenic adsorption rate tests.

  16. Monte Carlo simulations of Protein Adsorption

    NASA Astrophysics Data System (ADS)

    Sharma, Sumit; Kumar, Sanat K.; Belfort, Georges

    2008-03-01

    Amyloidogenic diseases, such as, Alzheimer's are caused by adsorption and aggregation of partially unfolded proteins. Adsorption of proteins is a concern in design of biomedical devices, such as dialysis membranes. Protein adsorption is often accompanied by conformational rearrangements in protein molecules. Such conformational rearrangements are thought to affect many properties of adsorbed protein molecules such as their adhesion strength to the surface, biological activity, and aggregation tendency. It has been experimentally shown that many naturally occurring proteins, upon adsorption to hydrophobic surfaces, undergo a helix to sheet or random coil secondary structural rearrangement. However, to better understand the equilibrium structural complexities of this phenomenon, we have performed Monte Carlo (MC) simulations of adsorption of a four helix bundle, modeled as a lattice protein, and studied the adsorption behavior and equilibrium protein conformations at different temperatures and degrees of surface hydrophobicity. To study the free energy and entropic effects on adsorption, Canonical ensemble MC simulations have been combined with Weighted Histogram Analysis Method(WHAM). Conformational transitions of proteins on surfaces will be discussed as a function of surface hydrophobicity and compared to analogous bulk transitions.

  17. Functionalized SBA-15 materials for bilirubin adsorption

    NASA Astrophysics Data System (ADS)

    Tang, Tao; Zhao, Yanling; Xu, Yao; Wu, Dong; Xu, Jun; Deng, Feng

    2011-05-01

    To investigate the driving force for bilirubin adsorption on mesoporous materials, a comparative study was carried out between pure siliceous SBA-15 and three functionalized SBA-15 mesoporous materials: CH 3-SBA-15 (MS), NH 2-SBA-15 (AS), and CH 3/NH 2-SBA-15 (AMS) that were synthesized by one-pot method. The obtained materials exhibited large surface areas (553-810 m 2/g) and pore size (6.6-7.1 nm) demonstrated by XRD and N 2-ad/desorption analysis. The SEM images showed that the materials had similar fiberlike morphology. The functionalization extent was calculated according to 29Si MAS NMR spectra and it was close to the designed value (10%). The synthesized mesoporous materials were used as bilirubin adsorbents and showed higher bilirubin adsorption capacities than the commercial active carbon. The adsorption capacities of amine functionalized samples AMS and AS were larger than those of pure siliceous SBA-15 and MS, indicating that electrostatic interaction was the dominant driving force for bilirubin adsorption on mesoporous materials. Increasing the ionic strength of bilirubin solution by adding NaCl would decrease the bilirubin adsorption capacity of mesoporous material, which further demonstrated that the electrostatic interaction was the dominant driving force for bilirubin adsorption. In addition, the hydrophobic interaction provided by methyl groups could promote the bilirubin adsorption.

  18. Adsorption and Processes in Spacecraft Environmental Control and Life Support Systems

    NASA Technical Reports Server (NTRS)

    Dall-Bauman, Liese; Finn, John E.; Kliss, Mark (Technical Monitor)

    1997-01-01

    The environmental control and life support system on a spacecraft must maintain a safe and comfortable environment in which the crew can live and work. The system's functions include supplying the crew with oxygen and water, as well as removing carbon dioxide, water vapor, and trace contaminants from cabin air. Although open-loop systems have been used in the past, logistics and safety factors of current and future missions in space make near-complete recycling of the cabin's air and water desirable. The recycling process may include separation and reduction of carbon dioxide, removal of trace gas-phase contaminants, recovery and purification of humidity condensate, purification and polishing of wastewater streams, and other processes. Several of these operations can be performed totally or in part by adsorption processes. Adsorption processes are frequently good candidates for separation and purification in space by virtue of such characteristics as gravity independence, high reliability, relatively high energy efficiency, design flexibility, technological maturity, and regenerability. For these reasons, adsorption has historically played a key role in life support on U.S. and Russian piloted spacecraft. This article focuses on three current spacecraft life support applications that often use adsorption technology: carbon dioxide separation from cabin air, gas-phase trace contaminant control, and potable water recovery from waste streams. In each application, adsorption technology has been selected for use on the International Space Station. The requirements, science, and hardware for each application are discussed. Eventually, human space exploration may lead to construction of planetary habitats. These habitats may have additional applications, such as control of greenhouse gas composition and purification of hydroponic solutions, and may have different requirements and resources available to them, such as gases present in the planetary atmosphere. Adsorption

  19. Comparison of the Adsorption of Fe(III) on Alpha- and Gamma-MnO2 Nanostructure

    NASA Astrophysics Data System (ADS)

    Dinh, Van-Phuc; Le, Ngoc-Chung; Le, Thi-Diem; Bui, Tan-Anh; Nguyen, Ngoc-Tuan

    2017-01-01

    Aqueous industrial wastes from heavy industry factories contain a large amount of Fe ions, which constitute a hazard for human life even at trace concentrations. Adsorption technology is a promising method for removing Fe(III) from aqueous solutions. In this report, the adsorption of the Fe(III) ion on γ- and α-MnO2 nanostructures was compared. The results showed that the maximum adsorption was obtained at pH = 3.5 for both materials after 120 min for γ-MnO2 and 80 min for α-MnO2. Adsorption isotherm models, such as Langmuir, Freundlich, Sips, Tempkin, and Dubinin-Radushkevich were applied to determine adsorption capacity as well as the nature of the uptake. The highest R 2, the smallest of root mean squared error (RMSE), and the nonlinear Chi-square test (χ2) values determined that the Sips model was the most appropriate equation to describe the adsorption of Fe(III) on γ- and α-MnO2. The maximum monolayer adsorption capacity calculated from the Langmuir model and the maximum adsorption capacity calculated from the Sips model of γ-MnO2 was more than four times that of α-MnO2. The heat of the adsorption as well as the mean free energy estimated from Tempkin and Dubinin-Radushkevich was determined to be less than 8 kJ/mol, which showed that the adsorption on both materials followed a physical process. Kinetic studies showed that a pseudo-second-order model was accurately described on both samples with three stages.

  20. Adsorption of amylase enzyme on ultrafiltration membranes.

    PubMed

    Beier, Søren Prip; Enevoldsen, Ann Dorrit; Kontogeorgis, Georgios M; Hansen, Ernst B; Jonsson, Gunnar

    2007-08-28

    A method to measure the static adsorption on membrane surfaces has been developed and described. The static adsorption of amylase-F has been measured on two different ultrafiltration membranes, both with a cutoff value of 10 kDa (a PES membrane and the ETNA10PP membrane, which is a surface-modified PVDF membrane). The adsorption follows the Langmuir adsorption theory. Thus, the static adsorption consists of monolayer coverage and is expressed both as a permeability drop and an adsorption resistance. From the adsorption isotherms, the maximum static permeability drops and the maximum static adsorption resistances are determined. The maximum static permeability drop for the hydrophobic PES membrane is 75%, and the maximum static adsorption resistance is 0.014 m2.h.bar/L. The maximum static permeability drop for the hydrophilic surface-modified PVDF membrane (ETNA10PP) is 23%, and the maximum static adsorption resistance is 0.0046 m2.h.bar/L. The difference in maximum static adsorption, by a factor of around 3, affects the performance during the filtration of a 5 g/L amylase-F solution at 2 bar. The two membranes behave very similarly during filtration with almost equal fluxes and retentions even though the initial water permeability of the PES membrane is around 3 times larger than the initial water permeability of the ETNA10PP membrane. This is mainly attributed to the larger maximum static adsorption of the PES membrane. The permeability drop during filtration exceeds the maximum static permeability drop, indicating that the buildup layer on the membranes during filtration exceeds monolayer coverage, which is also seen by the increase in fouling resistance during filtration. The accumulated layer on the membrane surface can be described as a continually increasing cake-layer thickness, which is independent of the membrane type. At higher concentrations of enzyme, concentration polarization effects cannot be neglected. Therefore, stagnant film theory and the osmotic

  1. Apparatus for the study of macromolecular adsorption

    NASA Astrophysics Data System (ADS)

    Mayo, C. S.; Hallock, R. B.

    1989-04-01

    A surface plasmon adsorbate monitor (SPAM) is described which allows the adsorption of macromolecules or other adsorbates to a metal surface to be monitored. Surface plasmons are employed and the apparatus has no moving parts. The kinetics of adsorption may be studied on a time scale of seconds rather than the more common time scale of minutes; a simple improvement in computer memory access should allow temporal studies in the millisecond range. As an illustration, the adsorption of carboxyl-terminated polystyrene from a solution with acetone onto a silver surface is measured.

  2. Adsorption of lead over graphite oxide.

    PubMed

    Olanipekun, Opeyemi; Oyefusi, Adebola; Neelgund, Gururaj M; Oki, Aderemi

    2014-01-24

    The adsorption efficiency and kinetics of removal of lead in presence of graphite oxide (GO) was determined using the Atomic Absorption Spectrophotometer (AAS). The GO was prepared by the chemical oxidation of graphite and characterized using FTIR, SEM, TGA and XRD. The adsorption efficiency of GO for the solution containing 50, 100 and 150 ppm of Pb(2+) was found to be 98%, 91% and 71% respectively. The adsorption ability of GO was found to be higher than graphite. Therefore, the oxidation of activated carbon in removal of heavy metals may be a viable option to reduce pollution in portable water.

  3. Adsorption characteristics of PCBs to resins, whole cells, cell and tissue components, and biomolecules

    SciTech Connect

    Kelley, R.L.; Conrad, J.; Akin, C.

    1990-01-01

    Polychlorinated biphenyls (PCBs) have been designated hazardous chemicals by the US Environmental Protection Agency (EPA). Although PCBs and PCB-containing oils have not been in use since 1977, they persist in the environment. They are known to be absorbed by various aquatic organisms, birds, and mammals. The nature of these affinities is not known. In this study, the Institute of Gas Technology (IGT) compared the adsorption phenomenon of PCBs on commercial resins, whole bacterial cells, cell and tissue component, and various biomolecules. Adsorption and desorption of PCBs to biomolecules and resins in both aqueous and nonaqueous conditions were examined. 9 refs., 7 figs., 2 tabs.

  4. Albumin (BSA) Adsorption over Graphene in Aqueous Environment: Influence of Orientation, Adsorption Protocol, and Solvent Treatment.

    PubMed

    Vilhena, J G; Rubio-Pereda, Pamela; Vellosillo, Perceval; Serena, P A; Pérez, Rubén

    2016-02-23

    We report 150 ns explicit solvent MD simulations of the adsorption on graphene of albumin (BSA) in two orientations and using two different adsorption protocols, i.e., free and forced adsorption. Our results show that free adsorption occurs with little structural rearrangements. Even taking adsorption to an extreme, by forcing it with a 5 nN downward force applied during the initial 20 ns, we show that along a particular orientation BSA is able to preserve the structural properties of the majority of its binding sites. Furthermore, in all the cases considered in this work, the ibuprofen binding site has shown a strong resilience to structural changes. Finally, we compare these results with implicit solvent simulations and find that the latter predicts an extreme protein unfolding upon adsorption. The origin of this discrepancy is attributed to a poor description of the water entropic forces at interfaces in the implicit solvent methods.

  5. MODELING COMPETITIVE ADSORPTION IN UREA-SCR CATALYSTS FOR EFFECTIVE LOW TEMPERATURE NOX CONTROL

    SciTech Connect

    Devarakonda, Maruthi N.; Tonkyn, Russell G.; Tran, Diana N.; Lee, Jong H.; Herling, Darrell R.

    2010-09-17

    Although the SCR technology exhibits higher NOx reduction efficiency over a wider range of temperatures among the lean NOx reduction technologies, further improvement in low-temperature performance is required to meet the future emission standards and to lower the system cost. In order to improve the catalyst technologies and optimize the system performance, it is critical to understand the reaction mechanisms and catalyst behaviors with respect to operating conditions. For example, it is well known that the ammonia coverage on catalyst surface is critical for NOx reduction efficiency. However, the level of ammonia storage is influenced by competitive adsorption by other species, such as H2O and NO2. Moreover, hydrocarbon species that slip through the upstream DOC during the cold-start period can also inhibit the SCR performance, especially at low temperatures. Therefore, a one-dimensional detailed kinetic model that can account for the effects of such competitive adsorption has been developed based on steady state surface isotherm tests on a commercial Fe-zeolite catalyst. The model is developed as a C language S-function and implemented in Matlab/Simulink environment. Rate kinetics of adsorption and desorption of each of the adsorbents are determined from individual adsorption tests and validated for a set of test conditions that had all the adsorbents in the feed gas.

  6. Adsorption characteristics of siloxanes in landfill gas by the adsorption equilibrium test

    SciTech Connect

    Nam, Sangchul; Namkoong, Wan; Kang, Jeong-Hee; Park, Jin-Kyu; Lee, Namhoon

    2013-10-15

    Highlights: • Equilibrium test was attempted to evaluate adsorption characteristics of siloxane. • L2 had higher removal efficiency in carbon compared to noncarbon adsorbents. • Total adsorption capacity of siloxane was 300 mg/g by coal activated carbon. • Adsorption characteristics rely on size of siloxane molecule and adsorbent pore. • Conversion of siloxane was caused by adsorption of noncarbon adsorbents. - Abstract: Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane.

  7. Adsorption Isotherms and Surface Reaction Kinetics

    ERIC Educational Resources Information Center

    Lobo, L. S.; Bernardo, C. A.

    1974-01-01

    Explains an error that occurs in calculating the conditions for a maximum value of a rate expression for a bimolecular reaction. The rate expression is derived using the Langmuir adsorption isotherm to relate gas pressures and corresponding surface coverages. (GS)

  8. Capillary condensation and adsorption of binary mixtures.

    PubMed

    Weinberger, B; Darkrim-Lamari, F; Levesque, D

    2006-06-21

    The adsorption of equimolar binary mixtures of hydrogen-carbon dioxide, hydrogen-methane, and methane-carbon dioxide in porous material models is determined by grand canonical Monte Carlo simulations. The material models have an adsorbent surface similar to that of nanofibers with a herringbone structure. Our main result, which is relevant for hydrogen purification and carbon dioxide capture, is that the adsorption selectivities calculated for the mixtures can differ significantly from those deduced from simulations of the adsorption of pure gases, in particular, when one of the adsorbed gases presents a capillary condensation induced by confinement within the pore network. A comparison of our data is also made with theoretical models used in the literature for predicting the properties of the mixture adsorption.

  9. Fluorocarbon Adsorption in Hierarchical Porous Frameworks

    SciTech Connect

    Motkuri, Radha K.; Annapureddy, Harsha V.; Vijayakumar, M.; Schaef, Herbert T.; Martin, P F.; McGrail, B. Peter; Dang, Liem X.; Krishna, Rajamani; Thallapally, Praveen K.

    2014-07-09

    The adsorption behavior of a series of fluorocarbon derivatives was examined on a set of microporous metal organic framework (MOF) sorbents and another set of hierarchical mesoporous MOFs. The microporous M-DOBDC (M = Ni, Co) showed a saturation uptake capacity for R12 of over 4 mmol/g at a very low relative saturation pressure (P/Po) of 0.02. In contrast, the mesoporous MOF MIL-101 showed an exceptionally high uptake capacity reaching over 14 mmol/g at P/Po of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption were found to generally correlate with the polarizability of the refrigerant with R12 > R22 > R13 > R14 > methane. These results suggest the possibility of exploiting MOFs for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling and refrigeration applications.

  10. Adsorption of nisin and pediocin on nanoclays.

    PubMed

    Meira, Stela Maris Meister; Jardim, Arthur Izé; Brandelli, Adriano

    2015-12-01

    Three different nanoclays (bentonite, octadecylamine-modified montmorillonite and halloysite) were studied as potential carriers for the antimicrobial peptides nisin and pediocin. Adsorption occurred from peptide solutions in contact with nanoclays at room temperature. Higher adsorption of nisin and pediocin was obtained on bentonite. The antimicrobial activity of the resultant bacteriocin-nanoclay systems was analyzed using skimmed milk agar as food simulant and the largest inhibition zones were observed against Gram-positive bacteria for halloysite samples. Bacteriocins were intercalated into the interlayer space of montmorillonites as deduced from the increase of the basal spacing measured by X-ray diffraction (XRD) assay. Infrared spectroscopy suggested non-electrostatic interactions, such as hydrogen bonding between siloxane groups from clays and peptide molecules. Transmission electron microscopy did not show any alteration in morphologies after adsorption of antimicrobial peptides on bentonite and halloysite. These results indicate that nanoclays, especially halloysite, are suitable nanocarriers for nisin and pediocin adsorption.

  11. Ionic Adsorption and Desorption of CNT Nanoropes

    PubMed Central

    Shang, Jun-Jun; Yang, Qing-Sheng; Yan, Xiao-Hui; He, Xiao-Qiao; Liew, Kim-Meow

    2016-01-01

    A nanorope is comprised of several carbon nanotubes (CNTs) with different chiralities. A molecular dynamic model is built to investigate the ionic adsorption and desorption of the CNT nanoropes. The charge distribution on the nanorope is obtained by using a modified gradient method based on classical electrostatic theory. The electrostatic interactions among charged carbon atoms are calculated by using the Coulomb law. It was found here that the charged nanorope can adsorb heavy metal ions, and the adsorption and desorption can be realized by controlling the strength of applied electric field. The distance between the ions and the nanorope as well as the amount of ions have an effect on the adsorption capacity of the nanorope. The desorption process takes less time than that of adsorption. The study indicates that the CNT nanorope can be used as a core element of devices for sewage treatment. PMID:28335306

  12. H2O Adsorption Kinetics on Smectites

    NASA Technical Reports Server (NTRS)

    Zent, Aaron P.; Howard, J.; Quinn, R. C.

    2000-01-01

    The adsorptive equilibration of H2O with montomorillonite has been measured. At low temperatures and pressures equilibration can require many hours, effectively preventing smectites at the martian surface from responding to diurnal pressure and temperature variations.

  13. Argon adsorption and the lunar atmosphere

    NASA Technical Reports Server (NTRS)

    Bernatowicz, T. J.; Podosek, F. A.

    1991-01-01

    The results of Ar adsorption experiments on a terrestrial labradorite and lunar rock 15415 crushed in vacuo are reported. The experiments were designed to test lunar atmosphere simulation models for the behavior of Ar on the lunar surface, as determined from the Apollo 17 mass spectrometer results. These models (Hodges, 1980, 1982) used a single adsorption potential to characterize the surfaces of lunar soil grains, with the result that high (6-7 kcal/mol) heats of adsorption were inferred. The present experimental results show that very high adsorption potentials are indeed associated with fresh mineral surfaces, but that these energetic surfaces occupy only small fractions of the total surface area. Nonetheless, these small fractions of surface, if they can be maintained in the lunar regolith in steady-state condition, could be sufficient to account for the Apollo 17 mass spectrometer observations.

  14. Krypton based adsorption type cryogenic refrigerator

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor); Schember, Helene R. (Inventor)

    1989-01-01

    Krypton and a monolithic porous carbon such as Saran carbon are used respectively as the sorbate and sorbent of an adsorption type refrigerator to improve refrigeration efficiency and operational longevity.

  15. Methane Adsorption on Aggregates of Fullerenes: Site-Selective Storage Capacities and Adsorption Energies

    PubMed Central

    Kaiser, Alexander; Zöttl, Samuel; Bartl, Peter; Leidlmair, Christian; Mauracher, Andreas; Probst, Michael; Denifl, Stephan; Echt, Olof; Scheier, Paul

    2013-01-01

    Methane adsorption on positively charged aggregates of C60 is investigated by both mass spectrometry and computer simulations. Calculated adsorption energies of 118–281 meV are in the optimal range for high-density storage of natural gas. Groove sites, dimple sites, and the first complete adsorption shells are identified experimentally and confirmed by molecular dynamics simulations, using a newly developed force field for methane–methane and fullerene–methane interaction. The effects of corrugation and curvature are discussed and compared with data for adsorption on graphite, graphene, and carbon nanotubes. PMID:23744834

  16. Methane adsorption on aggregates of fullerenes: site-selective storage capacities and adsorption energies.

    PubMed

    Kaiser, Alexander; Zöttl, Samuel; Bartl, Peter; Leidlmair, Christian; Mauracher, Andreas; Probst, Michael; Denifl, Stephan; Echt, Olof; Scheier, Paul

    2013-07-01

    Methane adsorption on positively charged aggregates of C60 is investigated by both mass spectrometry and computer simulations. Calculated adsorption energies of 118-281 meV are in the optimal range for high-density storage of natural gas. Groove sites, dimple sites, and the first complete adsorption shells are identified experimentally and confirmed by molecular dynamics simulations, using a newly developed force field for methane-methane and fullerene-methane interaction. The effects of corrugation and curvature are discussed and compared with data for adsorption on graphite, graphene, and carbon nanotubes.

  17. Dynamic adsorption of diarrhetic shellfish poisoning (DSP) toxins in passive sampling relates to pore size distribution of aromatic adsorbent.

    PubMed

    Li, Aifeng; Ma, Feifei; Song, Xiuli; Yu, Rencheng

    2011-03-18

    Solid-phase adsorption toxin tracking (SPATT) technology was developed as an effective passive sampling method for dissolved diarrhetic shellfish poisoning (DSP) toxins in seawater. HP20 and SP700 resins have been reported as preferred adsorption substrates for lipophilic algal toxins and are recommended for use in SPATT testing. However, information on the mechanism of passive adsorption by these polymeric resins is still limited. Described herein is a study on the adsorption of OA and DTX1 toxins extracted from Prorocentrum lima algae by HP20 and SP700 resins. The pore size distribution of the adsorbents was characterized by a nitrogen adsorption method to determine the relationship between adsorption and resin porosity. The Freundlich equation constant showed that the difference in adsorption capacity for OA and DTX1 toxins was not determined by specific surface area, but by the pore size distribution in particular, with micropores playing an especially important role. Additionally, it was found that differences in affinity between OA and DTX1 for aromatic resins were as a result of polarity discrepancies due to DTX1 having an additional methyl moiety.

  18. Carbon nanotube membranes with ultrahigh specific adsorption capacity for water desalination and purification.

    PubMed

    Yang, Hui Ying; Han, Zhao Jun; Yu, Siu Fung; Pey, Kin Leong; Ostrikov, Kostya; Karnik, Rohit

    2013-01-01

    Development of technologies for water desalination and purification is critical to meet the global challenges of insufficient water supply and inadequate sanitation, especially for point-of-use applications. Conventional desalination methods are energy and operationally intensive, whereas adsorption-based techniques are simple and easy to use for point-of-use water purification, yet their capacity to remove salts is limited. Here we report that plasma-modified ultralong carbon nanotubes exhibit ultrahigh specific adsorption capacity for salt (exceeding 400% by weight) that is two orders of magnitude higher than that found in the current state-of-the-art activated carbon-based water treatment systems. We exploit this adsorption capacity in ultralong carbon nanotube-based membranes that can remove salt, as well as organic and metal contaminants. These ultralong carbon nanotube-based membranes may lead to next-generation rechargeable, point-of-use potable water purification appliances with superior desalination, disinfection and filtration properties.

  19. Adsorption and characterization of MCPA on DDTMA- and raw-montmorillonite: Surface sites involved.

    PubMed

    Santiago, Cintia C; Fernández, Mariela A; Torres Sánchez, Rosa M

    2016-01-01

    The 4-chloro-2-methylphenoxy acid (MCPA) is an herbicide widely used in agriculture, which generates a great concern about contamination of surface water and serious consequences for human health and the environment. In this work, the adsorption of MCPA on an Argentine montmorillonite (MMT) and its organo-montmorillonite product (OMMT) with different dodecyl trimethyl ammonium loading was investigated. MCPA adsorption on OMMT increases at least 3 times, with respect to the amount determined for MMT. X-ray diffraction and zeta potential analyses indicated the inner (interlayer) and outer surface participate as adsorption sites. Changes in surface electric charge and also interlayer expansion suggest that dimethyl amine (MCPA counterion) was also surface-adsorbed. The larger aggregates of OMMT, without and with MCPA, obtained compared to those of MMT samples, generate an improvement in the coagulation efficiency. This property, particularly after MCPA retention, allows an easier separation of the solids from the solution and enables a simple technological process application.

  20. Improving the hydrogen oxidation reaction rate by promotion of hydroxyl adsorption.

    PubMed

    Strmcnik, Dusan; Uchimura, Masanobu; Wang, Chao; Subbaraman, Ram; Danilovic, Nemanja; van der Vliet, Dennis; Paulikas, Arvydas P; Stamenkovic, Vojislav R; Markovic, Nenad M

    2013-04-01

    The development of hydrogen-based energy sources as viable alternatives to fossil-fuel technologies has revolutionized clean energy production using fuel cells. However, to date, the slow rate of the hydrogen oxidation reaction (HOR) in alkaline environments has hindered advances in alkaline fuel cell systems. Here, we address this by studying the trends in the activity of the HOR in alkaline environments. We demonstrate that it can be enhanced more than fivefold compared to state-of-the-art platinum catalysts. The maximum activity is found for materials (Ir and Pt₀.₁Ru₀.₉) with an optimal balance between the active sites that are required for the adsorption/dissociation of H₂ and for the adsorption of hydroxyl species (OHad). We propose that the more oxophilic sites on Ir (defects) and PtRu material (Ru atoms) electrodes facilitate the adsorption of OHad species. Those then react with the hydrogen intermediates (Had) that are adsorbed on more noble surface sites.

  1. Defluoridation of drinking water using adsorption processes.

    PubMed

    Loganathan, Paripurnanda; Vigneswaran, Saravanamuthu; Kandasamy, Jaya; Naidu, Ravi

    2013-03-15

    Excessive intake of fluoride (F), mainly through drinking water, is a serious health hazard affecting humans worldwide. There are several methods used for the defluoridation of drinking water, of which adsorption processes are generally considered attractive because of their effectiveness, convenience, ease of operation, simplicity of design, and for economic and environmental reasons. In this paper, we present a comprehensive and a critical literature review on various adsorbents used for defluoridation, their relative effectiveness, mechanisms and thermodynamics of adsorption, and suggestions are made on choice of adsorbents for various circumstances. Effects of pH, temperature, kinetics and co-existing anions on F adsorption are also reviewed. Because the adsorption is very weak in extremely low or high pHs, depending on the adsorbent, acids or alkalis are used to desorb F and regenerate the adsorbents. However, adsorption capacity generally decreases with repeated use of the regenerated adsorbent. Future research needs to explore highly efficient, low cost adsorbents that can be easily regenerated for reuse over several cycles of operations without significant loss of adsorptive capacity and which have good hydraulic conductivity to prevent filter clogging during the fixed-bed treatment process.

  2. Gibbs adsorption and the compressibility equation

    SciTech Connect

    Aranovich, G.L.; Donohue, M.D.

    1995-08-08

    A new approach for deriving the equation of state is developed. It is shown that the integral in the compressibility equation is identical to the isotherm for Gibbs adsorption in radial coordinates. The Henry, Langmuir, and Frumkin adsorption isotherms are converted into equations of state. It is shown that using Henry`s law gives an expression for the second virial coefficient that is identical to the result from statistical mechanics. Using the Langmuir isotherm leads to a new analytic expression for the hard-sphere equation of state which can be explicit in either pressure or density. The Frumkin isotherm results in a new equation of state for the square-well potential fluid. Conversely, new adsorption isotherms can be derived from equations of state using the compressibility equation. It is shown that the van der Waals equation gives an adsorption isotherm equation that describes both polymolecular adsorption and the unusual adsorption behavior observed for supercritical fluids. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.

  3. Differential Heat of Adsorption and Isosteres.

    PubMed

    Tian, Yun; Wu, Jianzhong

    2017-01-31

    Heat of adsorption is a basic thermodynamic property extensively used not only for understanding thermal effects and heat management in industrial gas storage and separation processes but also for development and validation of adsorption models and materials force fields. Despite a long history of theoretical studies and a vast experimental literature, controversies often arise in the thermodynamic analysis of heat effects due to various assumptions used to describe gas adsorption and inconsistencies between direct calorimetric measurements and isosteric heat obtained from various adsorption isotherms. Here we present a rigorous theoretical procedure for predicting isosteric heat without any assumption about the geometry of porous adsorbents or operating conditions. Quantitative relations between the differential heat and various isosteres have been established with the grand-canonical Monte Carlo simulation for gas adsorption in amorphous as well as crystalline porous materials. The inconsistencies and practical issues with conventional methods for the analysis of the heat effect have been clarified in the context of the exact results for model systems. Via the resolution of a number of controversies about heat analysis, we hope that the new theoretical procedure will be adopted for both fundamental research and industrial applications of gas adsorption processes.

  4. Gas adsorption capacity of wood pellets

    DOE PAGES

    Yazdanpanah, F.; Sokhansanj, Shahabaddine; Lim, C. Jim; ...

    2016-02-03

    In this paper, temperature-programmed desorption (TPD) analysis was used to measure and analyze the adsorption of off-gases and oxygen by wood pellets during storage. Such information on how these gases interact with the material helps in the understanding of the purging/stripping behavior of off-gases to develop effective ventilation strategies for wood pellets. Steam-exploded pellets showed the lowest carbon dioxide (CO2) uptake compared to the regular and torrefied pellets. The high CO2 adsorption capacity of the torrefied pellets could be attributed to their porous structure and therefore greater available surface area. Quantifying the uptake of carbon monoxide by pellets was challengingmore » due to chemical adsorption, which formed a strong bond between the material and carbon monoxide. The estimated energy of desorption for CO (97.8 kJ/mol) was very high relative to that for CO2 (7.24 kJ/mol), demonstrating the mechanism of chemical adsorption and physical adsorption for CO and CO2, respectively. As for oxygen, the strong bonds that formed between the material and oxygen verified the existence of chemical adsorption and formation of an intermediate material.« less

  5. Gas adsorption capacity of wood pellets

    SciTech Connect

    Yazdanpanah, F.; Sokhansanj, Shahabaddine; Lim, C. Jim; Lau, A.; Bi, X. T.

    2016-02-03

    In this paper, temperature-programmed desorption (TPD) analysis was used to measure and analyze the adsorption of off-gases and oxygen by wood pellets during storage. Such information on how these gases interact with the material helps in the understanding of the purging/stripping behavior of off-gases to develop effective ventilation strategies for wood pellets. Steam-exploded pellets showed the lowest carbon dioxide (CO2) uptake compared to the regular and torrefied pellets. The high CO2 adsorption capacity of the torrefied pellets could be attributed to their porous structure and therefore greater available surface area. Quantifying the uptake of carbon monoxide by pellets was challenging due to chemical adsorption, which formed a strong bond between the material and carbon monoxide. The estimated energy of desorption for CO (97.8 kJ/mol) was very high relative to that for CO2 (7.24 kJ/mol), demonstrating the mechanism of chemical adsorption and physical adsorption for CO and CO2, respectively. As for oxygen, the strong bonds that formed between the material and oxygen verified the existence of chemical adsorption and formation of an intermediate material.

  6. Carbon dioxide adsorption in graphene sheets

    NASA Astrophysics Data System (ADS)

    Mishra, Ashish Kumar; Ramaprabhu, Sundara

    2011-09-01

    Control over the CO2 emission via automobiles and industrial exhaust in atmosphere, is one of the major concerns to render environmental friendly milieu. Adsorption can be considered to be one of the more promising methods, offering potential energy savings compared to absorbent systems. Different carbon nanostructures (activated carbon and carbon nanotubes) have attracted attention as CO2 adsorbents due to their unique surface morphology. In the present work, we have demonstrated the CO2 adsorption capacity of graphene, prepared via hydrogen induced exfoliation of graphitic oxide at moderate temperatures. The CO2 adsorption study was performed using high pressure Sieverts apparatus and capacity was calculated by gas equation using van der Waals corrections. Physical adsorption of CO2 molecules in graphene was confirmed by FTIR study. Synthesis of graphene sheets via hydrogen exfoliation is possible at large scale and lower cost and higher adsorption capacity of as prepared graphene compared to other carbon nanostructures suggests its possible use as CO2 adsorbent for industrial application. Maximum adsorption capacity of 21.6 mmole/g was observed at 11 bar pressure and room temperature (25 °C).

  7. Cr-Doped ZnO Nanoparticles: Synthesis, Characterization, Adsorption Property, and Recyclability.

    PubMed

    Meng, Alan; Xing, Jing; Li, Zhenjiang; Li, Qingdang

    2015-12-16

    In this paper, a mild solvothermal method has been employed to successfully synthesize a series of Cr-doped ZnO nanoparticles (NPs) with different Cr(3+) contents, which is a kind of novel and high-efficiency absorbent for the removal of acid dye methyl orange (MO) from aqueous solution. The as-prepared products were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), Brunauer, Emmet, and Teller (BET), and Zeta potential measurements. In accordance with the adsorption capacity of the products, the obtained optimal Cr/Zn molar ratio is 6%. The adsorption process of MO on Cr-doped ZnO was investigated by kinetics, thermodynamics, and isotherm technologies, which, respectively, indicated that the adsorption was fast (adsorption reached equilibrium in 2 h) and followed a pseudo-second-order model, that the adsorption process was spontaneous and endothermic, and that it agreed well with the Langmuir isotherm with a maximum adsorption capacity of 310.56 mg g(-1). Moreover, a reasonable mechanism was proposed to elucidate the reasons for their adsorption behavior. In addition, a simple and low-cost chemical method was developed to separate and recycle ZnO and MO from the used adsorbent, effectively avoiding the secondary pollution. This work can not only describe efficient experimental approaches for obtaining novel adsorbents and recycling them but also offer valuable clues for the preparation and property study of other semiconductor adsorbents.

  8. Effect of oxidation and catalytic reduction of trace organic contaminants on their activated carbon adsorption.

    PubMed

    Schoutteten, Klaas V K M; Hennebel, Tom; Dheere, Ellen; Bertelkamp, Cheryl; De Ridder, David J; Maes, Synthia; Chys, Michael; Van Hulle, Stijn W H; Vanden Bussche, Julie; Vanhaecke, Lynn; Verliefde, Arne R D

    2016-12-01

    The combination of ozonation and activated carbon (AC) adsorption is an established technology for removal of trace organic contaminants (TrOCs). In contrast to oxidation, reduction of TrOCs has recently gained attention as well, however less attention has gone to the combination of reduction with AC adsorption. In addition, no literature has compared the removal behavior of reduction vs. ozonation by-products by AC. In this study, the effect of pre-ozonation vs pre-catalytic reduction on the AC adsorption efficiency of five TrOCs and their by-products was compared. All compounds were susceptible to oxidation and reduction, however the catalytic reductive treatment proved to be a slower reaction than ozonation. New oxidation products were identified for dinoseb and new reduction products were identified for carbamazepine, bromoxynil and dinoseb. In terms of compatibility with AC adsorption, the influence of the oxidative and reductive pretreatments proved to be compound dependent. Oxidation products of bromoxynil and diatrizoic acid adsorbed better than their parent TrOCs, but oxidation products of atrazine, carbamazepine and dinoseb showed a decreased adsorption. The reductive pre-treatment showed an enhanced AC adsorption for dinoseb and a major enhancement for diatrizoic acid. For atrazine and bromoxynil, no clear influence on adsorption was noted, while for carbamazepine, the reductive pretreatment resulted in a decreased AC affinity. It may thus be concluded that when targeting mixtures of TrOCs, a trade-off will undoubtedly have to be made towards overall reactivity and removal of the different constituents, since no single treatment proves to be superior to the other.

  9. Designated drivers: the differing roles of divalent metal ions in surfactant adsorption at the oil-water interface.

    PubMed

    Robertson, Ellen J; Beaman, Daniel K; Richmond, Geraldine L

    2013-12-17

    Divalent metal ions play numerous roles in biological, technological, and environmental systems. This study examines the role of a variety of ions, Mg(2+), Ca(2+), Mn(2+), Ni(2+), Cu(2+), and Zn(2+), in the adsorption of sodium decanoate at the carbon tetrachloride-water interface. For all ions studied, the ions drive the adsorption of the surfactant to the interface. Using vibrational sum-frequency spectroscopy and the carboxylic acid vibrational modes as a signature for metal ion binding, each metal salt is found to play a distinctly different role in the molecular characteristics of surfactant adsorption at the interface. Additional spectroscopic studies of the methyl and methylene vibrations are monitored to track the ordering of the alkyl chains when metal salts are added to solution. How the metal-surfactant binding impacts the surfactant structure, orientation, and solvation is explored. How these spectroscopic measurements compare with the degree of adsorption as measured by interfacial tension data is presented.

  10. Adsorption of quinolone, tetracycline, and penicillin antibiotics from aqueous solution using activated carbons: Review.

    PubMed

    Ahmed, Muthanna J

    2017-03-01

    Antibiotics, an important type of pharmaceutical pollutant, have attracted many researchers to the study of their removal from aqueous solutions. Activated carbon (AC) has been widely used as highly effective adsorbent for antibiotics because of its large specific surface area, high porosity, and favorable pore size distribution. In this article, the adsorption performance of AC towards three major types of antibiotics such as tetracyclines, quinolones, and penicillins were reviewed. According to collected data, maximum adsorption capacities of 1340.8, 638.6, and 570.4mg/g were reported for tetracyclines, quinolones, and penicillins, respectively. The values of 1/n for Freundlich isotherm were less than unity, suggesting that the adsorption was nonlinear and favorable. Adsorption kinetics followed closely the pseudo-second-order model and analysis using the Weber-Morris model revealed that the intra-particle diffusion was not the only rate controlling step. AC adsorption demonstrated superior performance for all selected drugs, thus being efficient technology for treatment of these pollutants.

  11. Coupling of Spinosad Fermentation and Separation Process via Two-Step Macroporous Resin Adsorption Method.

    PubMed

    Zhao, Fanglong; Zhang, Chuanbo; Yin, Jing; Shen, Yueqi; Lu, Wenyu

    2015-08-01

    In this paper, a two-step resin adsorption technology was investigated for spinosad production and separation as follows: the first step resin addition into the fermentor at early cultivation period to decrease the timely product concentration in the broth; the second step of resin addition was used after fermentation to adsorb and extract the spinosad. Based on this, a two-step macroporous resin adsorption-membrane separation process for spinosad fermentation, separation, and purification was established. Spinosad concentration in 5-L fermentor increased by 14.45 % after adding 50 g/L macroporous at the beginning of fermentation. The established two-step macroporous resin adsorption-membrane separation process got the 95.43 % purity and 87 % yield for spinosad, which were both higher than that of the conventional crystallization of spinosad from aqueous phase that were 93.23 and 79.15 % separately. The two-step macroporous resin adsorption method has not only carried out the coupling of spinosad fermentation and separation but also increased spinosad productivity. In addition, the two-step macroporous resin adsorption-membrane separation process performs better in spinosad yield and purity.

  12. Adsorption of the natural protein surfactant Rsn-2 onto liquid interfaces.

    PubMed

    Brandani, Giovanni B; Vance, Steven J; Schor, Marieke; Cooper, Alan; Kennedy, Malcolm W; Smith, Brian O; MacPhee, Cait E; Cheung, David L

    2017-03-22

    To stabilize foams, droplets and films at liquid interfaces a range of protein biosurfactants have evolved in nature. Compared to synthetic surfactants, these combine surface activity with biocompatibility and low solution aggregation. One recently studied example is Rsn-2, a component of the foam nest of the frog Engystomops pustulosus, which has been predicted to undergo a clamshell-like opening transition at the air-water interface. Using atomistic molecular dynamics simulations and surface tension measurements we study the adsorption of Rsn-2 onto air-water and cyclohexane-water interfaces. The protein adsorbs readily at both interfaces, with adsorption mediated by the hydrophobic N-terminus. At the cyclohexane-water interface the clamshell opens, due to the favourable interaction between hydrophobic residues and cyclohexane molecules and the penetration of cyclohexane molecules into the protein core. Simulations of deletion mutants showed that removal of the N-terminus inhibits interfacial adsorption, which is consistent with the surface tension measurements. Deletion of the hydrophilic C-terminus also affects adsorption, suggesting that this plays a role in orienting the protein at the interface. The characterisation of the interfacial behaviour gives insight into the factors that control the interfacial adsorption of proteins, which may inform new applications of this and similar proteins in areas including drug delivery and food technology and may also be used in the design of synthetic molecules showing similar changes in conformation at interfaces.

  13. Adsorption of mixed cationic-nonionic surfactant and its effect on bentonite structure.

    PubMed

    Zhang, Yaxin; Zhao, Yan; Zhu, Yong; Wu, Huayong; Wang, Hongtao; Lu, Wenjing

    2012-01-01

    The adsorption of cationic-nonionic mixed surfactant onto bentonite and its effect on bentonite structure were investigated. The objective was to improve the understanding of surfactant behavior on clay mineral for its possible use in remediation technologies of soil and groundwater contaminated by toxic organic compounds. The cationic surfactant used was hexadecylpyridinium bromide (HDPB), and the nonionic surfactant was Triton X-100 (TX100). Adsorption of TX100 was enhanced significantly by the addition of HDPB, but this enhancement decreased with an increase in the fraction of the cationic surfactant. Part of HDPB was replaced by TX100 which decreased the adsorption of HDPB. However, the total adsorbed amount of the mixed surfactant was still increased substantially, indicating the synergistic effect between the cationic and nonionic surfactants. The surfactant-modified bentonite was characterized by Brunauer-Emmett-Teller specific surface area measurement, Fourier transform infrared spectroscopy, and thermogravimetric-derivative thermogravimetric/differential thermal analyses. Surfactant intercalation was found to decrease the bentonite specific surface area, pore volume, and surface roughness and irregularities, as calculated by nitrogen adsorption-desorption isotherms. The co-adsorption of the cationic and nonionic surfactants increased the ordering conformation of the adsorbed surfactants on bentonite, but decreased the thermal stability of the organobentonite system.

  14. Adsorption of aqueous copper on peanut hulls

    NASA Astrophysics Data System (ADS)

    Davis, Kanika Octavia

    A method was established for measuring the adsorption of Cu(II) from aqueous solution to unmodified and modified peanut hulls at constant temperature and pH. Modification of the hulls was performed by oxidation with alkaline hydrogen peroxide. During the modification process, the hydrogen peroxide solubilizes the lignin component, making the surface more porous which increases the availability of binding sites, while simultaneously oxidizing the cellulose. The oxidation of alcohol groups creates more binding sites by creating functional groups such as COO-, which increases chelation to metal ions. Fourier transform infrared spectroscopy confirms delignification of the peanut hulls by the disappearance of carboxyl peaks of the modified hulls, which were originally produced from the lignin content. Although, oxidation is not fully confirmed, it is not ruled out because the expected carboxylate peak (1680 cm-1) maybe overshadowed by a broad peak due to OH bending of water adsorbed to the hulls. Hulls adsorbed copper from solutions in the concentration range of 50-1000 ppm of CuCl2. Concentrations of pre- and post-adsorption solutions were determined using inductively coupled plasma optical emission spectroscopy. The adsorption isotherms were fit to known two and three-parameter models, evaluated and the binding mechanism was inferred. Maximum surface coverage was 3.5 +/- 0.6 mg Cu2+ /g hull for unmodified hulls and 11 +/- 1 mg Cu2+/g hull for modified hulls. The adsorption for the hulls is best described by the Langmuir model, suggesting monolayer, homogeneous adsorption. With a free energy of adsorption of 10.5 +/- 0.9 kJ/mol for unmodified hulls and 14.5 +/-0.4 kJ/mol for modified hulls, the process is categorized as chemisorption for both types of hulls. The adsorption for both hulls is also described by the Redlich-Peterson model, giving beta nearer to 1 than 0, which further suggests homogeneous adsorption described by the Langmuir model. After rinsing the hulls

  15. Heavy metal adsorption changes of EAF steel slag after phosphorus adsorption.

    PubMed

    Song, Guanling; Cao, Lijing; Chen, Xiao; Hou, Wenhua; Wang, Qunhui

    2012-01-01

    A kind of electric arc furnace (EAF) steel slag was phosphated, and its isothermal and dynamic adsorptions of copper, cadmium, and lead ions were measured to determine if heavy metal adsorption changes after phosphorus adsorption. The surface area increased greatly after the slag was phosphated. Isothermal adsorption experiments showed that the theoretical Q(max) of the EAF steel slag on Cu(2+), Cd(2+), and Pb(2+) improved 59, 50, and 89% respectively after it was phosphated. Dynamic adsorption results showed that the greatest adsorption capacities of unit volume of Cu(2+), Cd(2+), and Pb(2+) were 2.2, 1.8, and 1.8 times that of the column packed with original EAF steel slag when the column was packed with phosphate EAF steel slag at the same heavy metal ion concentration. The breakthrough time, the exhaustion time and elution efficiency of the column also increased when the column was packed with phosphated EAF steel slag compared with that packed with original EAF steel slag. Phosphorus adsorption could further improve the heavy metal ion adsorption of the EAF steel slag.

  16. Theoretical study of the adsorption of DOPA-quinone and DOPA-quinone chlorides on Cu (1 0 0) surface

    NASA Astrophysics Data System (ADS)

    Chen, Shuang-Kou; Wang, Bo-Chu; Zhou, Tai-Gang; Huang, Wen-Zhang

    2011-07-01

    The marine mussel secreted adhesive proteins and could bind strongly to all kinds of surfaces. Studies indicated that there was an unusual amino acid 3,4-dihydroxy-L-phenylanine (DOPA). DOPA could be oxidized to DOPA-quinone easily, which had a superior ability to on surface directly. The technology of electrolyzing seawater was employed to generate HOCl solution to react with DOPA-quinone and form DOPA-quinone chlorides (DOPA-quinone-Cl) to hinder the adhesion. However, the detailed hinder-mechanism remained unknown to be fully explained. Herein, using quantum chemical density functional theory methods, we have systematically studied three kinds of adsorption for DOPA-quinone and DOPA-quinone-Cl on Cu (1 0 0) surface: hydroxyl oxygen-side vertical, carbonyl oxygen-side vertical, amino N-terminal vertical adsorptions and carried out geometry optimization and energy calculation. The results showed that two molecules could absorb on the Cu (1 0 0) through hydroxyl oxygen-side vertical adsorption, while the other two kinds of adsorption could not form an effective adsorption. Calculations of adsorption energy for hydroxyl oxygen-side vertical adsorption indicated that: after HOCl modification, adsorption energy decreased from -247.2310 kJ/mol to -177.0579 kJ/mol for DOPA-quinone and DOPA-quinone-Cl; and the Mulliken Charges Populations showed that the electrons transferred from surface to DOPA-quinone-Cl was less than that to DOPA-quinone, namely, the fewer the number of electrons transferred, the weaker interaction between molecular and surface. After the theoretical calculation, we found that the anti-foul goal had been achieved by electrolysis of seawater to generate HOCl to modify DOPA-quinone, which led to the reduction of adsorption energy and transferred electrons.

  17. Poliovirus Adsorption by 34 Minerals and Soils

    PubMed Central

    Moore, Rebecca S.; Taylor, Dene H.; Sturman, Lawrence S.; Reddy, Michael M.; Fuhs, G. Wolfgang

    1981-01-01

    The adsorption of radiolabeled infectious poliovirus type 2 by 34 well-defined soils and mineral substrates was analyzed in a synthetic freshwater medium containing 1 mM CaCl2 and 1.25 mM NaHCO3 at pH 7. In a model system, adsorption of poliovirus by Ottawa sand was rapid and reached equilibrium within 1 h at 4°C. Near saturation, the adsorption could be described by the Langmuir equation; the apparent surface saturation was 2.5 × 106 plaque-forming units of poliovirus per mg of Ottawa sand. At low surface coverage, adsorption was described by the Freundlich equation. The soils and minerals used ranged from acidic to basic and from high in organic content to organic free. The available negative surface charge on each substrate was measured by the adsorption of a cationic polyelectrolyte, polydiallyldimethylammonium chloride. Most of the substrates adsorbed more than 95% of the virus. In general, soils, in comparison with minerals, were weak adsorbents. Among the soils, muck and Genesee silt loam were the poorest adsorbents; among the minerals, montmorillonite, glauconite, and bituminous shale were the least effective. The most effective adsorbents were magnetite sand and hematite, which are predominantly oxides of iron. Correlation coefficients for substrate properties and virus adsorption revealed that the elemental composition of the adsorbents had little effect on poliovirus uptake. Substrate surface area and pH, by themselves, were not significantly correlated with poliovirus uptake. A strong negative correlation was found between poliovirus adsorption and both the contents of organic matter and the available negative surface charge on the substrates as determined by their capacities for adsorbing the cationic polyelectrolyte, polydiallyldimethylammonium chloride. PMID:6274259

  18. Toward Accurate Adsorption Energetics on Clay Surfaces

    PubMed Central

    2016-01-01

    Clay minerals are ubiquitous in nature, and the manner in which they interact with their surroundings has important industrial and environmental implications. Consequently, a molecular-level understanding of the adsorption of molecules on clay surfaces is crucial. In this regard computer simulations play an important role, yet the accuracy of widely used empirical force fields (FF) and density functional theory (DFT) exchange-correlation functionals is often unclear in adsorption systems dominated by weak interactions. Herein we present results from quantum Monte Carlo (QMC) for water and methanol adsorption on the prototypical clay kaolinite. To the best of our knowledge, this is the first time QMC has been used to investigate adsorption at a complex, natural surface such as a clay. As well as being valuable in their own right, the QMC benchmarks obtained provide reference data against which the performance of cheaper DFT methods can be tested. Indeed using various DFT exchange-correlation functionals yields a very broad range of adsorption energies, and it is unclear a priori which evaluation is better. QMC reveals that in the systems considered here it is essential to account for van der Waals (vdW) dispersion forces since this alters both the absolute and relative adsorption energies of water and methanol. We show, via FF simulations, that incorrect relative energies can lead to significant changes in the interfacial densities of water and methanol solutions at the kaolinite interface. Despite the clear improvements offered by the vdW-corrected and the vdW-inclusive functionals, absolute adsorption energies are often overestimated, suggesting that the treatment of vdW forces in DFT is not yet a solved problem. PMID:27917256

  19. Apparatus for thermal swing adsorption and thermally-enhanced pressure swing adsorption

    DOEpatents

    Wegeng, Robert S.; Rassat, Scot D.; Stenkamp, Victoria S.; TeGrotenhuis, Ward E.; Matson, Dean W.; Drost, M. Kevin; Viswanathan, Vilayanur V.

    2005-12-13

    The present invention provides compact adsorption systems that are capable of rapid temperature swings and rapid cycling. Novel methods of thermal swing adsorption and thermally-enhanced pressure swing adsorption are also described. In some aspects of the invention, a gas is passed through the adsorbent thus allowing heat exchangers to be very close to all portions of the adsorbent and utilize less space. In another aspect, the adsorption media is selectively heated, thus reducing energy costs. Methods and systems for gas adsorption/desorption having improved energy efficiency with capability of short cycle times are also described. Advantages of the invention include the ability to use (typically) 30-100 times less adsorbent compared to conventional systems.

  20. Method for thermal swing adsorption and thermally-enhanced pressure swing adsorption

    DOEpatents

    Wegeng, Robert S.; Rassat, Scot D.; Stenkamp, Victoria S.; TeGrotenhuis, Ward E.; Matson, Dean W.; Drost, M. Kevin; Viswanathan, Vilayanur V.

    2003-10-07

    The present invention provides compact adsorption systems that are capable of rapid temperature swings and rapid cycling. Novel methods of thermal swing adsorption and thermally-enhanced pressure swing adsorption are also described. In some aspects of the invention, a gas is passed through the adsorbent thus allowing heat exchangers to be very close to all portions of the adsorbent and utilize less space. In another aspect, the adsorption media is selectively heated, thus reducing energy costs. Methods and systems for gas adsorption/desorption having improved energy efficiency with capability of short cycle times are also described. Advantages of the invention include the ability to use (typically) 30-100 times less adsorbent compared to conventional systems.

  1. Method and apparatus for thermal swing adsorption and thermally-enhanced pressure swing adsorption

    DOEpatents

    Wegeng, Robert S.; Rassat, Scot D.; TeGrotenhuis, Ward E.; Drost, Kevin; Vishwanathan, Vilayanur V.

    2004-06-08

    The present invention provides compact adsorption systems that are capable of rapid temperature swings and rapid cycling. Novel methods of thermal swing adsorption and thermally-enhanced pressure swing adsorption are also described. In some aspects of the invention, a gas is passed through the adsorbent thus allowing heat exchangers to be very close to all portions of the adsorbent and utilize less space. In another aspect, the adsorption media is selectively heated, thus reducing energy costs. Methods and systems for gas adsorption/desorption having improved energy efficiency with capability of short cycle times are also described. In another aspect, the apparatus or methods utilize heat exchange channels of varying lengths that have volumes controlled to provide equal heat fluxes. Methods of fuel cell startup are also described. Advantages of the invention include the ability to use (typically) 30-100 times less adsorbent compared to conventional systems.

  2. Conceptual adsorption models and open issues pertaining to performance assessment

    SciTech Connect

    Serne, R.J.

    1991-10-01

    Recently several articles have been published that question the appropriateness of the distribution coefficient, Rd, concept to quantify radionuclide migration. Several distinct issues are raised by various critics. In this paper I provide some perspective on issues surrounding the modeling of nuclide retardation. The first section defines adsorption terminology and discusses various adsorption processes. The next section describes five commonly used adsorption conceptual models, specifically emphasizing what attributes that affect adsorption are explicitly accommodated in each model. I also review efforts to incorporate each adsorption model into performance assessment transport computer codes. The five adsorption conceptual models are (1) the constant Rd model, (2) the parametric Rd model, (3) isotherm adsorption models, (4) mass-action adsorption models, and (5) surface-complexation with electrostatics models. The final section discusses the adequacy of the distribution ratio concept, the adequacy of transport calculations that rely on constant retardation factors and the status of incorporating sophisticated adsorption models into transport codes.

  3. Adsorption of phenolic compound by aged-refuse.

    PubMed

    Xiaoli, Chai; Youcai, Zhao

    2006-09-01

    The adsorption of phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol by aged-refuse has been studied. Adsorption isotherms have been determined for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol and the data fits well to the Freundlich equation. The chlorinated phenols are absorbed more strongly than the phenol and the adsorption capacity has an oblivious relationship with the numbers and the position of chlorine subsistent. The experiment data suggests that both the partition function and the chemical adsorption involve in the adsorption process. Pseudo-first-order and pseudo-second-order model were applied to investigate the kinetics of the adsorption and the results show that it fit the pseudo-second-order model. More than one step involves in the adsorption process and the overall rate of the adsorption process appears to be controlled by the chemical reaction. The thermodynamic analysis indicates that the adsorption is spontaneous and endothermic.

  4. Equilibrium and Heat of Adsorption for Organic Vapors and Activated Carbons

    DTIC Science & Technology

    2005-05-01

    Technol. 2005, 39, 5864-5871 5864 9 ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 39, NO. 15, 2005 10.1021/es048144r CCC: $30.25  2005 American Chemical...0.654 VOL. 39, NO. 15, 2005 / ENVIRONMENTAL SCIENCE & TECHNOLOGY 9 5865 have due to the drag force on the sample pan. In addition, the N2 flow prevented...results are provided as lines. 5866 9 ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 39, NO. 15, 2005 Increasing the adsorption temperature from 20 to 60 °C

  5. Neptunium(V) adsorption to calcite.

    PubMed

    Heberling, Frank; Brendebach, Boris; Bosbach, Dirk

    2008-12-12

    The migration behavior of the actinyl ions U(VI)O2(2+), Np(V)O2+ and Pu(V,VI)O2(+,2+) in the geosphere is to a large extend controlled by sorption reactions (inner- or outer-sphere adsorption, ion-exchange, coprecipitation/structural incorporation) with minerals. Here NpO2+ adsorption onto calcite is studied in batch type experiments over a wide range of pH (6.0-9.4) and concentration (0.4 microM-40 microM) conditions. pH is adjusted by variation of CO2 partial pressure. Adsorption is found to be pH dependent with maximal adsorption at pH 8.3 decreasing with increasing and decreasing pH. pH dependence of adsorption decreases with increasing Np(V) concentration. EXAFS data of neptunyl adsorbed to calcite and neptunyl in the supernatant shows differences in the Np(V)-O-yl distance, 1.85+/-0.01 angstroms for the adsorbed and 1.82+/-0.01 angstroms for the solution species. The equatorial environment of the neptunyl in solution shows about 5 oxygen neighbours at 2.45+/-0.02 angstroms. For adsorbed neptunyl there are also about 5 oxygen neighbours at 2.46+/-0.01 angstroms. An additional feature in the adsorbed species' R-space spectrum can be related to carbonate neighbours, 3 to 6 carbon backscatterers (C-eq) at 3.05+/-0.03 angstroms and 3 to 6 oxygen backscatterers (O-eq2) at 3.31+/-0.02 angstroms. The differences in the Np(V)-O-yl distance and the C-eq and O-eq2 backscatterers which are only present for the adsorbed species indicate inner-sphere bonding of the adsorbed neptunyl species to the calcite surface. Experiments on adsorption kinetics indicate that after a fast surface adsorption process a continuous slow uptake occurs which may be explained by incorporation via surface dissolution and reprecipitation processes. This is also indicated by the part irreversibility of the adsorption as shown by increased KD values after desorption compared to adsorption.

  6. Phosphorus recovery using pelletized adsorptive materials ...

    EPA Pesticide Factsheets

    Phosphorous (P) is one of the essential nutrients for growth and is generally the most limiting nutrient since, it cannot be fixed from the atmosphere. Methods for recovering phosphorous from water systems already exist, but advances are being made to find a more economic, efficient, effective and easy to use method that can allow for reuse of the recovered P. One area of study is in adsorption, which involves finding the best material for adsorption of phosphorous from water and for releasing it back into the environment through desorption or leaching. The goal of this research was to first optimize the capacity for a pelletized adsorptive material that was synthesized with varying amounts of a binder material from 0-20 % and then to study recovering the phosphate for reuse. The pelletized materials were studied through kinetics experiments as well as isotherm experiments to gain insight into the adsorption capacity and mechanism. Following successful adsorption, a simple leaching study was conducted to see how much phosphate would be released back into water without any added desorption aid. Desorption was then studied by changing the pH of solution. Presenting my thesis work with a poster at ACS.

  7. Adsorption behavior of heavy metals on biomaterials.

    PubMed

    Minamisawa, Mayumi; Minamisawa, Hiroaki; Yoshida, Shoichiro; Takai, Nobuharu

    2004-09-08

    We have investigated adsorption of Cd(II) and Pb(II) at pH 2-6.7 onto the biomaterials chitosan, coffee, green tea, tea, yuzu, aloe, and Japanese coarse tea, and onto the inorganic adsorbents, activated carbon and zeolite. High adsorptive capabilities were observed for all of the biomaterials at pH 4 and 6.7. In the adsorption of Cd(II), blend coffee, tea, green tea, and coarse tea have comparable loading capacities to activated carbon and zeolite. Although activated carbon, zeolite, and chitosan are utilized in a variety of fields such as wastewater treatment, chemical and metallurgical engineering, and analytical chemistry, these adsorbents are costly. On the other hand, processing of the test biomaterials was inexpensive, and all the biomaterials except for chitosan were able to adsorb large amounts of Pb(II) and Cd(II) ions after a convenient pretreatment of washing with water followed by drying. The high adsorption capability of the biomaterials prepared from plant materials is promising in the development of a novel, low-cost adsorbent. From these results, it is concluded that heavy metal removal using biomaterials would be an effective method for the economic treatment of wastewater. The proposed adsorption method was applied to the determination of amounts of Cd(II) and Pb(II) in water samples.

  8. Sulfate adsorption in Michigan forest soils

    SciTech Connect

    MacDonald, N.W.

    1987-01-01

    The occurrence of acidic atmospheric deposition raised concerns over adverse cation leaching effects on Michigan forest soils with low cation exchange capacities. Leaching effects of acid deposition depend on mobility of sulfate in the soil. Little was known, however, concerning the ability of these soils to adsorb sulfate. The objectives of this study were to determine the ability of representative Michigan forest soils to adsorb sulfate, to relate sulfate adsorption to soil properties, and to develop equations to predict sulfate adsorption in similar forest soils. Frigid zone soil series studied were Grayling (Typic Udipsamments), Rubicon (Entic Haplorthods), Kalkaska (Typic Haplorthods), and Montcalm (Eutric Glossoboralfs). Mesic zone series studied were Spinks (Psammentic Hapludals) and Oshtemo (Typic Hapludalfs). Six randomly located pedons of each series were sampled. Sulfate adsorption was determined by shaking 10 gram soil samples for 24 hours in 50 mL 0.01 M CaCl/sub 2/ solution containing 10 mg SO/sub 4/-S L/sup -1/. Solution filtrates were turbidimetrically analyzed for SO/sub 4/-S and adsorption was calculated from reduction in SO/sub 4/-S concentration. Bw, Bs, and Bh horizons of frigid zone soils and E and Bt horizons of mesic zone soils had the highest sulfate adsorbing abilities. No significant differences were found between series in total sulfate adsorptive capacity.

  9. DNA adsorption by indium tin oxide nanoparticles.

    PubMed

    Liu, Biwu; Liu, Juewen

    2015-01-01

    The high conductivity and optical transparency of indium tin oxide (ITO) has made it a popular material in the electronic industry. Recently, its application in biosensors is also explored. To understand its biointerface chemistry, we herein investigate its interaction with fluorescently labeled single-stranded oligonucleotides using ITO nanoparticles (NPs). The fluorescence of DNA is efficiently quenched after adsorption, and the interaction between DNA and ITO NPs is strongly dependent on the surface charge of ITO. At low pH, the ITO surface is positively charged to afford a high DNA adsorption capacity. Adsorption is also influenced by the sequence and length of DNA. For its components, In2O3 adsorbs DNA more strongly while SnO2 repels DNA at neutral pH. The DNA adsorption property of ITO is an averaging result from both components. DNA adsorption is confirmed to be mainly by the phosphate backbone via displacement experiments using free phosphate or DNA bases. Last, DNA-induced DNA desorption by forming duplex DNA is demonstrated on ITO, while the same reaction is more difficult to achieve on other metal oxides including CeO2, TiO2, and Fe3O4 because these particles adsorb DNA more tightly.

  10. Adsorption of Wine Constituents on Functionalized Surfaces.

    PubMed

    Mierczynska-Vasilev, Agnieszka; Smith, Paul A

    2016-10-18

    The adsorption of macromolecules on solid surfaces is of great importance in the field of nanotechnology, biomaterials, biotechnological, and food processes. In the field of oenology adsorption of wine macromolecules such as polyphenols, polysaccharides, and proteins is much less desirable on membrane materials because of fouling and reduced filtering performance. On the other hand, adsorption of these molecules on processing aids is very beneficial for achieving wine clarity and stability. In this article, the effect of surface chemical functionalities on the adsorption of white, rosé, and red wine constituents was evaluated. Allylamine, acrylic acid, and ethanol were selected as precursors for plasma polymerization in order to generate coatings rich in amine, carboxyl, and hydroxyl chemical groups, respectively. The surface chemical functionalities were characterized by X-ray photoelectron spectroscopy (XPS) and the ability of different surface chemical functionalities to adsorb wine constituents were characterized by quartz crystal microbalance with dissipation (QCM-D) and atomic force microscopy (AFM). The results demonstrated that the amine and carboxyl modified surfaces encourage adsorption of constituents from white wine. The hydroxyl modified surfaces have the ability to preferentially adsorb rosé wine constituents, whereas red wine adsorbed to the highest extent on acrylic acid surface.

  11. Adsorption of phenanthrene on natural snow.

    PubMed

    Domine, Florent; Cincinelli, Alessandra; Bonnaud, Elodie; Martellini, Tania; Picaud, Sylvain

    2007-09-01

    The snowpack is a reservoir for semivolatile organic compounds (SVOCs) and, in particular, for persistent organic pollutants (POPs), which are sequestered in winter and released to the atmosphere or hydrosphere in the spring. Modeling these processes usually assumes that SVOCs are incorporated into the snowpack by adsorption to snow surfaces, but this has never been proven because the specific surface area (SSA) of snow has never been measured together with snow composition. Here we expose natural snow to phenanthrene vapors (one of the more volatile POPs) and measure for the first time both the SSA and the chemical composition of the snow. The results are consistent with an adsorption equilibrium. The measured Henry's law constant is H(Phen)(T) = 2.88 x 10(22) exp(-10660/7) Pa m2 mol(-1), with Tin Kelvin. The adsorption enthalpy is delta H(ads) = -89 +/- 18 kJ mol(-1). We also perform molecular dynamics calculations of phenanthrene adsorption to ice and obtain AHads = -85 +/- 8 kJ mol(-1), close to the experimental value. Results are applied to the adsorption of phenanthrene to the Arctic and subarctic snowpacks. The subarctic snowpack, with a low snow area index (SAI = 1000), is a negligible reservoir of phenanthrene, butthe colder Arctic snowpack, with SAI = 2500, sequesters most of the phenanthrene present in the (snow + boundary layer) system.

  12. Adsorption of gases on carbon molecular sieves

    SciTech Connect

    Vyas, S.N.; Patwardhan, S.R.; Vijayalakshmi, S. . Dept. of Chemical Engineering); Ganesh, K.S. )

    1994-12-01

    Adsorption on carbon molecular sieves (CMS) prepared by coke deposition has become an interesting area of adsorption due to its microporous nature and favorable separation factor on size and shape selectivity basis for many gaseous systems. In the present work CMS was synthesized from coconut shell through three major steps, namely, carbonization, activation, and coke deposition by hydrocarbon cracking. The crushed, washed, and sieved granules of coconut shell (particle size 2--3 mm) were pretreated with sodium silicate solution and oven-dried at 150 C to create the inorganic sites necessary for coke deposition. Carbonization and activation of the dried granules were carried out at 800 C, for 30 min each. The activated char thus produced was subjected to hydrocarbon cracking at 600 C for periods varying from 30 to 180 min. The product samples were characterized in terms of adsorption isotherm, kinetic adsorption curve, surface area, pore volume, pore size distribution, and characteristic energy for adsorption by using O[sub 2], N[sub 2], C[sub 2]H[sub 2], CO[sub 2], C[sub 3]H[sub 6], and CH[sub 4].

  13. Comparative isosteric ion adsorption for minerals

    NASA Technical Reports Server (NTRS)

    Omenyi, Samuel N.; Herren, Blair J.; Snyder, Robert S.; Seaman, Geoffrey V. F.

    1986-01-01

    A comparative isosteric ion adsorption study for minerals (kaolinite, rutile, and quartz) was performed in aqueous solutions of CaCl2, LaCl3, and Th(NO3)4 in the presence of the neutral salt NaCl. It was observed that the concentration of Ca(2+) ions required to produce a standard reduction in the electrophoretic mobility of mineral particles was always appreciably greater than the concentration required for the Th(4+) ions. The effectiveness of adsorption of the cations differed from particle to particle and showed that ion adsorption on a mineral surface depends, among other things, on the nature of the mineral surface and on the particular adsorbed cation. The number of cation binding sites on mineral surfaces and the electrochemical free energies of cation adsorption were calculated. It was found that the adsorption energy of La(3+) and Th(4+) ions on rutile, kaolinite, and quartz was greater than that of Ca(2+) on these minerals.

  14. Adsorption of plutonium oxide nanoparticles.

    PubMed

    Schmidt, Moritz; Wilson, Richard E; Lee, Sang Soo; Soderholm, L; Fenter, P

    2012-02-07

    Adsorption of monodisperse cubic plutonium oxide nanoparticles ("Pu-NP", [Pu(38)O(56)Cl(x)(H(2)O)(y)]((40-x)+), with a fluorite-related lattice, approximately 1 nm in edge size) to the muscovite (001) basal plane from aqueous solutions was observed in situ (in 100 mM NaCl background electrolyte at pH 2.6). Uptake capacity of the surface quantified by α-spectrometry was 0.92 μg Pu/cm(2), corresponding to 10.8 Pu per unit cell area (A(UC)). This amount is significantly larger than that of Pu(4+) needed for satisfying the negative surface charge (0.25 Pu(4+) for 1 e(-)/A(UC)). The adsorbed Pu-NPs cover 17% of the surface area, determined by X-ray reflectivity (XR). This correlates to one Pu-NP for every 14 unit cells of muscovite, suggesting that each particle compensates the charge of the unit cells onto which it adsorbs as well as those in its direct proximity. Structural investigation by resonant anomalous X-ray reflectivity distinguished two different sorption states of Pu-NPs on the surface at two different regimes of distance from the surface. A fraction of Pu is distributed within 11 Å from the surface. The distribution width matches the Pu-NP size, indicating that this species represents Pu-NPs adsorbed directly on the surface. Beyond the first layer, an additional fraction of sorbed Pu was observed to extend more broadly up to more than 100 Å from the surface. This distribution is interpreted as resulting from "stacking" or aggregation of the nanoparticles driven by sorption and accumulation of Pu-NPs at the interface although these Pu-NPs do not aggregate in the solution. These results are the first in situ observation of the interaction of nanoparticles with a charged mineral-water interface yielding information important to understanding the environmental transport of Pu and other nanophase inorganic species.

  15. Impact of Adsorption on Gas Transport in Nanopores

    PubMed Central

    Wu, Tianhao; Zhang, Dongxiao

    2016-01-01

    Given the complex nature of the interaction between gas and solid atoms, the development of nanoscale science and technology has engendered a need for further understanding of gas transport behavior through nanopores and more tractable models for large-scale simulations. In the present paper, we utilize molecular dynamic simulations to demonstrate the behavior of gas flow under the influence of adsorption in nano-channels consisting of illite and graphene, respectively. The results indicate that velocity oscillation exists along the cross-section of the nano-channel, and the total mass flow could be either enhanced or reduced depending on variations in adsorption under different conditions. The mechanisms can be explained by the extra average perturbation stress arising from density oscillation via the novel perturbation model for micro-scale simulation, and approximated via the novel dual-region model for macro-scale simulation, which leads to a more accurate permeability correction model for industrial applications than is currently available. PMID:27020130

  16. UPGRADING METHANE USING ULTRA-FAST THERMAL SWING ADSORPTION

    SciTech Connect

    Anna Lee Tonkovich

    2004-01-01

    The purpose of this project is to design and demonstrate an approach to upgrade low-BTU methane streams from coal mines to pipeline-quality natural gas. The objective of Phase I of the project was to assess the feasibility of upgrading low-Btu methane streams using ultra-fast thermal swing adsorption (TSA) using Velocys' modular microchannel process technology. The project is on schedule and under budget. For Task 1.1, the open literature, patent information, and vendor contacts were surveyed to identify adsorbent candidates for experimental validation and subsequent demonstration in an MPT-based ultra-fast TSA separation for methane upgrading. The leading candidates for preferential adsorption of methane over nitrogen are highly microporous carbons. A Molecular Gate{trademark} zeolite from Engelhard Corporation has emerged as a candidate. For Task 1.2, experimental evaluation of adsorbents was initiated, and data were collected on carbon (MGN-101) from PICA, Inc. This carbon demonstrated a preferential capacity for methane over nitrogen, as well as a reasonable thermal swing differential capacity for a 90% methane and 10% nitrogen mixture. A similar methane swing capacity at 2 psig was measured. The mixture composition is relevant because gob gas contains nearly 85% methane and must be purified to 97% methane for pipeline quality.

  17. Water adsorption constrained Frenkel-Halsey-Hill adsorption activation theory: Montmorillonite and illite

    NASA Astrophysics Data System (ADS)

    Hatch, Courtney D.; Greenaway, Ann L.; Christie, Matthew J.; Baltrusaitis, Jonas

    2014-04-01

    Fresh mineral aerosol has recently been found to be effective cloud condensation nuclei (CCN) and contribute to the number of cloud droplets in the atmosphere due to the effect of water adsorption on CCN activation. The work described here uses experimental water adsorption measurements on Na-montmorillonite and illite clay to determine empirical adsorption parameters that can be used in a recently derived theoretical framework (Frenkel-Halsey-Hill Activation Theory, FHH-AT) that accounts for the effect of water adsorption on CCN activation. Upon fitting the Frenkel-Halsey-Hill (FHH) adsorption model to water adsorption measurements, we find FHH adsorption parameters, AFHH and BFHH, to be 98 ± 22 and 1.79 ± 0.11 for montmorillonite and 75 ± 17 and 1.77 ± 0.11 for illite, respectively. The AFHH and BFHH values obtained from water adsorption measurements differ from values reported previously determined by applying FHH-AT to CCN activation measurements. Differences in FHH adsorption parameters were attributed to different methods used to obtain them and the hydratable nature of the clays. FHH adsorption parameters determined from water adsorption measurements were then used to calculate the critical super-saturation (sc) for CCN activation using FHH-AT. The relationship between sc and the dry particle diameter (Ddry) gave CCN activation curve exponents (xFHH) of -0.61 and -0.64 for montmorillonite and illite, respectively. The xFHH values were slightly lower than reported previously for mineral aerosol. The lower exponent suggests that the CCN activity of hydratable clays is less sensitive to changes in Ddry and the hygroscopicity parameter exhibits a broader variability with Ddry compared to more soluble aerosols. Despite the differences in AFHH, BFHH and xFHH, the FHH-AT derived CCN activities of montmorillonite and illite are quite similar to each other and in excellent agreement with experimental CCN measurements resulting from wet-generated clay aerosol

  18. Molecular simulation of carbon dioxide adsorption for carbon capture and storage

    NASA Astrophysics Data System (ADS)

    Tenney, Craig M.

    Capture of CO2 from fossil fuel power plants and sequestration in unmineable coal seams are achievable methods for reducing atmospheric emissions of this greenhouse gas. To aid the development of effective CO2 capture and sequestration technologies, a series of molecular simulation studies were conducted to study the adsorption of CO2 and related species onto heterogeneous, solid adsorbents. To investigate the influence of surface heterogeneity upon adsorption behavior in activated carbons and coal, isotherms were generated via grand canonical Monte Carlo (GCMC) simulation for CO2 adsorption in slit-shaped pores with several variations of chemical and structural heterogeneity. Adsorption generally increased with increasing oxygen content and the presence of holes or furrows, which acted as preferred binding sites. To investigate the potential use of the flexible metal organic framework (MOF) Cu(BF4)2(bpy)2 (bpy=bipyridine) for CO2 capture, pure- and mixed-gas adsorption was simulated at conditions representative of power plant process streams. This MOF was chosen because it displays a novel behavior in which the crystal structure reversibly transitions from an empty, zero porosity state to a saturated, expanded state at the "gate pressure". Estimates of CO2 capacity above the gate pressure from GCMC simulations using a rigid MOF model showed good agreement with experiment. The CO2 adsorption capacity and estimated heats of adsorption are comparable to common physi-adsorbents under similar conditions. Mixed-gas simulations predicted CO2/N2 and CO2/H 2selectivities higher than typical microporous materials. To more closely investigate this gating effect, hybrid Monte-Carlo/molecular-dynamics (MCMD) was used to simulate adsorption using a flexible MOF model. Simulation cell volumes remained relatively constant at low gas pressures before increasing at higher pressure. Mixed-gas simulations predicted CO2/N 2 selectivities comparable to other microporous adsorbents. To

  19. Adsorption on Highly Ordered Porous Alumina

    NASA Astrophysics Data System (ADS)

    Mistura, Giampaolo; Bruschi, Lorenzo; Lee, Woo

    2016-10-01

    Porous anodic aluminum oxide (AAO) is characterized by a regular arrangement of the pores with a narrow pore size distribution over extended areas, uniform pore depth, and solid pore walls without micropores. Thanks to significant improvements in anodization techniques, structural engineering of AAO allows to accurately tailor the pore morphology. These features make porous AAO an excellent substrate to study adsorption phenomena. In this paper, we review recent experiments involving the adsorption in porous AAO. Particular attention will be devoted to adsorption in straight and structured pores with a closed end which shed new light on fundamental issues like the origin of hysteresis in closed end pores and the nature of evaporation from ink-bottle pores. The results will be compared to those obtained in other synthetic materials like porous silicon and silica.

  20. Porous silicon functionalization for possible arsenic adsorption

    PubMed Central

    2014-01-01

    Thiol-functionalized porous silicon (PS) monolayer was evaluated for its possible application in As (III) adsorption. Dimercaptosuccinic acid (DMSA) attached to mesoporous silicon via amide bond linkages was used as a chelate for As (III). Two different aminosilanes namely 3-(aminopropyl) triethoxysilane (APTES) and 3-aminopropyl (diethoxy)-methylsilane (APDEMS) were tested as linkers to evaluate the relative response for DMSA attachment. The aminosilane-modified PS samples were attached to DMSA by wet impregnation followed by the adsorption of As (III). Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) have been used to identify the functional groups and to estimate the As (III) content, respectively. FTIR spectroscopy confirmed the covalent bonding of DMSA with amide and R-COOH groups on the nanostructured porous surface. XPS confirms the preferred arsenic adsorption on the surface of PS/DMSA samples as compared to the aminosilane-modified and bare PS substrates. PMID:25249826

  1. Bromate adsorption using Fe-pillared bentonite.

    PubMed

    He, Shilong; Zhang, Dandan; Gu, Li; Zhang, Shenghua; Yu, Xin

    2012-01-01

    Bromate is an emerging hazardous substance in drinking water. In this study, the removal ofbromate by Fe-pillared bentonite was investigated using various experimental parameters: contact time, initial concentration (Co), temperature, initial pH and competing anions. The adsorption ofbromate followed the pseudo-second-order kinetic better than it followed other kinetic models, and the pseudo-second-order kinetic study showed that equilibrium could be achieved within 60 min. Equilibrium isotherms were analyzed by Freundlich, Langmuir, Redlich-Peterson and Toth isotherm models. The Toth and Redlich-Peterson models better represented the bromate adsorption. Results also indicated that, other than the competing anions and solution pH, temperature was a key parameter affecting adsorption. It was ultimately concluded that Fe-pillared bentonite was effective at removing bromate from water.

  2. Adsorption kinetics of silicic acid on akaganeite.

    PubMed

    Naren, Gaowa; Ohashi, Hironori; Okaue, Yoshihiro; Yokoyama, Takushi

    2013-06-01

    As part of a series of studies on the interaction between ferric ions and silicic acid in the hydrosphere, the adsorption of silicic acid on akaganeite was investigated kinetically at various pH values. The adsorption of silicic acid increased with increasing pH over an initial pH range of 4-11.5. In the kinetic experiment, the Cl(-) was released from akaganeite much faster than silicic acid was adsorbed. From this result, we concluded that chloride ions bound on the surface of akaganeite are released and Fe-OH or Fe-O(-) sites are formed, which then acts as an adsorption site for silicic acid. The uptake mechanism of silicic acid by akaganeite is significantly different from that by schwertmannite, despite the presence of the same tunnel structure.

  3. Cotton cellulose: enzyme adsorption and enzymic hydrolysis

    SciTech Connect

    Beltrame, P.L.; Carniti, P.; Focher, B.; Marzetti, A.; Cattaneo, M.

    1982-01-01

    The adsorption of a crude cellulase complex from Trichoderma viride on variously pretreated cotton cellulose samples was studied in the framework of the Langmuir approach at 2-8 degrees. The saturation amount of adsorbed enzyme was related to the susceptibility of the substrates to hydrolysis. In every case the adsorption process was faster by 2-3 orders of magnitude than the hydrolysis step to give end products. For ZnCl/sub 2/-treated cotton cellulose the Langmuir parameters correlated fairly well with the value of the Michaelis constant, measured for its enzymic hydrolysis, and the adsorptive complex was indistinguishable from the complex of the Michaelis-Menten model for the hydrolysis.

  4. Adsorption of monoclonal antibodies to glass microparticles.

    PubMed

    Hoehne, Matthew; Samuel, Fauna; Dong, Aichun; Wurth, Christine; Mahler, Hanns-Christian; Carpenter, John F; Randolph, Theodore W

    2011-01-01

    Microparticulate glass represents a potential contamination to protein formulations that may occur as a result of processing conditions or glass types. The effect of added microparticulate glass to formulations of three humanized antibodies was tested. Under the three formulation conditions tested, all three antibodies adsorbed irreversibly at near monolayer surface coverages to the glass microparticles. Analysis of the secondary structure of the adsorbed antibodies by infrared spectroscopy reveal only minor perturbations as a result of adsorption. Likewise, front-face fluorescence quenching measurements reflected minimal tertiary structural changes upon adsorption. In contrast to the minimal effects on protein structure, adsorption of protein to suspensions of glass microparticles induced significant colloidal destabilization and flocculation of the suspension.

  5. Novel nano bearings constructed by physical adsorption

    NASA Astrophysics Data System (ADS)

    Zhang, Yongbin

    2015-09-01

    The paper proposes a novel nano bearing formed by the physical adsorption of the confined fluid to the solid wall. The bearing is formed between two parallel smooth solid plane walls sliding against one another, where conventional hydrodynamic lubrication theory predicted no lubricating effect. In this bearing, the stationary solid wall is divided into two subzones which respectively have different interaction strengths with the lubricating fluid. It leads to different physical adsorption and slip properties of the lubricating fluid at the stationary solid wall respectively in these two subzones. It was found that a significant load-carrying capacity of the bearing can be generated for low lubricating film thicknesses, because of the strong physical adsorption and non-continuum effects of the lubricating film.

  6. Utilisation of chitinous materials in pigment adsorption.

    PubMed

    Wang, San-Lang; Chen, Yan-Cheng; Yen, Yue-Horng; Liang, Tzu-Wen

    2012-12-01

    The effect of adding the cells of four lactobacilli to a squid pen powder (SPP)-containing medium on prodigiosin (PG) production by Serratia marcescens TKU011 is examined. The best increase in PG productivity was shown by strain TKU012. Among the samples of strain TKU012 and the chitinous materials of cicada casting powder (CCP), shrimp shell powder (SSP), squid pen powder (SPP), α-chitin, and β-chitin, TKU012 cells displayed the best adsorption rate (84%) for PG, followed by CCP, SSP, SPP, α-chitin, and β-chitin. As for the water-soluble food colourants, Allura Red AC (R40) and Tartrazne (Y4), SPP and SSP had better adsorptive powers than pure chitin preparations, strain TKU012, and CCP. Treatment with organic solvents, hot alkali, or proteases (papain, bromelain) diminished the adsorption rates of the biosorbents.

  7. Effect of polymer adsorption on mobility ratio

    SciTech Connect

    Omar, A.E.

    1983-03-01

    Several properties of two of the viscous polymer fluids used in rheological control were investigated. Polymer adsorption on the rock surfaces of porous sandstones and its effect on permeability of producing formation was studied. A naturally occurring polymer, a Guar gum, was found greatly to reduce the permeability of the producing formation, although the use of a breaker solution was found to restore the permeability lost through polymer plugging. Use of appropriate breaker solution was found to reduce the permeability loss to only one or two per cent of the original value. Adsorption of the synthetic polymer, acrylamide, was found to be directly related to the shaliness of the porous sand. Deactivation of polymer due to adsorption was found to be significant in formations having large surface areas. The results indicate that polymer loss eventually results in a water bank ahead of the polymer solution and thus greatly reduces the polymer's effectiveness in water-flooding.

  8. Novel nano bearings constructed by physical adsorption

    PubMed Central

    Zhang, Yongbin

    2015-01-01

    The paper proposes a novel nano bearing formed by the physical adsorption of the confined fluid to the solid wall. The bearing is formed between two parallel smooth solid plane walls sliding against one another, where conventional hydrodynamic lubrication theory predicted no lubricating effect. In this bearing, the stationary solid wall is divided into two subzones which respectively have different interaction strengths with the lubricating fluid. It leads to different physical adsorption and slip properties of the lubricating fluid at the stationary solid wall respectively in these two subzones. It was found that a significant load-carrying capacity of the bearing can be generated for low lubricating film thicknesses, because of the strong physical adsorption and non-continuum effects of the lubricating film. PMID:26412488

  9. Porous silicon functionalization for possible arsenic adsorption

    NASA Astrophysics Data System (ADS)

    Balderas-Valadez, Ruth Fabiola; Agarwal, Vivechana

    2014-09-01

    Thiol-functionalized porous silicon (PS) monolayer was evaluated for its possible application in As (III) adsorption. Dimercaptosuccinic acid (DMSA) attached to mesoporous silicon via amide bond linkages was used as a chelate for As (III). Two different aminosilanes namely 3-(aminopropyl) triethoxysilane (APTES) and 3-aminopropyl (diethoxy)-methylsilane (APDEMS) were tested as linkers to evaluate the relative response for DMSA attachment. The aminosilane-modified PS samples were attached to DMSA by wet impregnation followed by the adsorption of As (III). Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) have been used to identify the functional groups and to estimate the As (III) content, respectively. FTIR spectroscopy confirmed the covalent bonding of DMSA with amide and R-COOH groups on the nanostructured porous surface. XPS confirms the preferred arsenic adsorption on the surface of PS/DMSA samples as compared to the aminosilane-modified and bare PS substrates.

  10. Adsorption of Gases on Carbon Nanotubes

    NASA Astrophysics Data System (ADS)

    Mbaye, Mamadou Thiao

    2014-01-01

    This research focus in studying the interaction between various classical and quantum gases with novel carbon nanostructures, mainly carbon nanotubes (CNTs). Since their discovery by the Japanese physicist Sumio Iijima [1] carbon nanotubes have, experimentally and theoretically, been subjected to many scientific investigation. Studies of adsorption on CNTs are particularly directed toward their better usage in gas storage, gas separation, catalyst, drug delivery, and water purification. We explore the adsorption of different gases entrapped in a single, double, or multi-bundles of CNTs using computer simulations. The first system we investigate consists of Ar and Kr films adsorbed on zigzag or armchair nanotubes. Our simulations revealed that Kr atoms on intermediate size zigzag NTs undergo two phase transitions: A liquid-vapor (L→V), and liquid-commensurate (L→CS) with a fractional coverage of one Kr atoms adsorbed for every four carbon atoms. For Ar on zigzag and armchair NTs, the only transition observed is a L→V. In the second problem, we explore the adsorption of CO2 molecules in a nanotube bundle and calculate the isosteric heat of adsorption of the entrapped molecules within the groove. We observed that the lower the temperature, the higher the isosteric of adsorption. Last, we investigate the adsorption of hydrogen, Helium, and Neon gases on the groove site of two parallel nanotubes. At low temperature, the transverse motion on the plane perpendicular to the tubes' axis is frozen out and as a consequence, the heat capacity is reduced to 1/2. At high temperature, the atoms gain more degree of freedom and as a consequence the heat capacity is 5/2.

  11. Adsorption of arsenate on untreated dolomite powder.

    PubMed

    Ayoub, G M; Mehawej, M

    2007-09-05

    Raw dolomite powder was evaluated for its efficiency in adsorbing As(V) from water. An experimental setup comprised of a fluidized dolomite powder bed was used to assess the impact of various test variables on the efficiency of removal of As(V). Test influents including distilled water (DW), synthetic groundwater (SGW) and filtered sewage effluent (FSE) were employed to assess the effect of influent parameters on the adsorption process and the quality of the effluent generated. Dolomite exhibited good As(V) removal levels for distilled water (>92%) and synthetic ground water (>84%) influents at all initial As(V) concentrations tested (0.055-0.600 ppm). Breakthrough of dolomite bed occurred after 45 bed volumes for DW and 20 bed volumes for SGW influents with complete breakthrough taking place at more than 300 bed volumes. As(V) removal from FSE influents was relatively unsuccessful as compared to the DW and SGW influents. Partial removal in the order of 32% from filtered sewage effluent at initial concentration of 0.6 mg/L started at 75 bed volumes and gradually stopped at 165 bed volumes. Varying degrees of As(V) adsorption capacities were observed by the different test influents employed, which indicate that the adsorption of As(V) is adversely affected by competing species, mainly sulfates and phosphates present in the influent. The adsorptive behavior of dolomite was described by fitting data generated from the study into the Langmuir and Freundlich isotherm models. Both models described well the adsorption of dolomite. The average isotherm adsorptive capacity was determined at 5.02 mug/g. Regeneration of the dolomite bed can be achieved with the use of caustic soda solution at a pH of 10.5.

  12. Applications and limits of theoretical adsorption models for predicting the adsorption properties of adsorbents.

    PubMed

    Park, Hyun Ju; Nguyen, Duc Canh; Na, Choon-Ki; Kim, Chung-il

    2015-01-01

    The objective of this study is to evaluate the applicability of adsorption models for predicting the properties of adsorbents. The kinetics of the adsorption of NO3- ions on a PP-g-AA-Am non-woven fabric have been investigated under equilibrium conditions in both batch and fixed bed column processes. The adsorption equilibrium experiments in the batch process were carried out under different adsorbate concentration and adsorbent dosage conditions and the results were analyzed using adsorption isotherm models, energy models, and kinetic models. The results of the analysis indicate that the adsorption occurring at a fixed adsorbate concentration with a varying adsorbent dosage occur more easily compared to those under a fixed adsorbent dosage with a varying adsorbate concentration. In the second part of the study, the experimental data obtained using fixed bed columns were fit to Bed Depth Service Time, Bohart-Adams, Clark, and Wolborska models, to predict the breakthrough curves and determine the column kinetic parameters. The adsorption properties of the NO3- ions on the PP-g-AA-Am non-woven fabric were differently described by different models for both the batch and fixed bed column process. Therefore, it appears reasonable to assume that the adsorption properties were dominated by multiple mechanisms, depending on the experimental conditions.

  13. Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite.

    PubMed

    Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

    2015-01-01

    Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g · L(-1), in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics.

  14. Study on the adsorption feature of rutin aqueous solution on macroporous adsorption resins.

    PubMed

    Chen, Zhenbin; Zhang, Anjie; Li, Jie; Dong, Fang; Di, Duolong; Wu, Youzhi

    2010-04-15

    The adsorption feature of different kinds of polystyrene-based macroporous adsorption resins (MARs) was investigated systemically at constant temperature employing Rutin as the adsorbate. Different from traditional adsorption patterns, Langmuir and Freundlich adsorption, and the results showed interesting aspects: (1) With the increase of the volume of the initial solution, the adsorption capacity increased to the maximum, and then decreased gradually. (2) Experimental results clearly verified the opinion that the adsorption process of MARs could be divided into three stages-macropores, mesopores, and micropores-by the capillary effects occurring at the two intersections, and the adsorption feature for every stage could be described well by the fourth type of Brunauer model. (3) The model that the inductive effect transmitted to the first layer could not interpret our experimental results reasonably. Thus, the model that the inductive effect passed on to a higher layer was proposed by investigating regression of the experimental results and the conclusion that the inductive effect transmitted to the third layer was drawn.

  15. Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite

    PubMed Central

    Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

    2015-01-01

    Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g·L-1, in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics. PMID:26698573

  16. [Evaluation and selection of VOCs treatment technologies in packaging and printing industry].

    PubMed

    Wang, Hai-Lin; Wang, Jun-Hui; Zhu, Chun-Lei; Nie, Lei; Hao, Zheng-Ping

    2014-07-01

    Volatile organic compounds (VOCs) play an important role in urban air pollution. Activities of industries including the packaging and printing industries are regarded as the major sources. How to select the suitable treating techniques is the major problem for emission control. In this article, based on the VOCs emission characteristics of the packaging and printing industry and the existing treatment technologies, using the analytic hierarchy process (AHP) model, an evaluation system for VOCs selection was established and all the technologies used for treatment were assessed. It showed that the priority selection was in the following order: Carbon Fiber Adsorption-Desorption > Granular Carbon Adsorption-Desorption > Thermal Combustion > Regenerative Combustion > Catalytic combustion > Rotary adsorption-concentration and combustion > Granular Carbon adsorption-concentration and combustion. Carbon Fiber Adsorption-Desorption was selected as the best available technology due to its highest weight among those technologies.

  17. Evaluating the Adsorptive Capabilites of Chemsorb 1000 and Chemsorb 1425

    NASA Technical Reports Server (NTRS)

    Mejia, Oscar Alberto Monje; Surma, Jan M.; Johnsey, Marissa; Melendez, Orlando

    2014-01-01

    The removal of trace contaminants from spacecraft cabin air is necessary for crew health and comfort during long duration space exploration missions. The air revitalization technologies used in these future exploration missions will evolve from current ISS ISS State-of-Art (SOA) and is being designed and tested by the Advanced Exploration Systems (AES) Program's Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project. The ARREM project is working to mature optimum atmosphere revitalization and environmental monitoring system architectures to enable exploration beyond Lower Earth Orbit (LEO). The Air Revitalization Lab at KSC is one of six NASA field centers participating in the ARREM that specializes in adsorbent and catalyst characterization with simulated spacecraft gas streams using combinations of pressure, O2 partial pressure, CO2 partial pressure, and humidity that are representative of a range of anticipated cabin atmospheric conditions and loads. On board ISS, the Trace Contaminant Control Subassembly (TCCS) provides active control of trace contaminants from the cabin atmosphere utilizing physical adsorption, thermal catalytic oxidation, and chemical adsorption processes. High molecular weight contaminants and ammonia (NH3) are removed a granular activated carbon treated with approx. 10% by weight phosphoric acid (H3PO4) (B-S Type 3032 4×6 mesh), which is expendable and is periodically refurbished. The Type 3032 granular activated carbon bed is no longer commercially available and therefore it is important to characterize the efficiency and capacity of commercially available NH3 sorbents. This paper describes the characterization of two Molecular Products LTD activated carbons: Chemsorb 1000 and Chemsorb 1425. Untreated activated carbons (e.g. Chemsorb 1000) remove contaminants by physisorption, which concentrates the contaminant within the pores of the carbon while letting air to pass through the sorbent4. Low molecular weight or polar

  18. Adsorption of deamidated antibody variants on macroporous and dextran-grafted cation exchangers: II. Adsorption kinetics.

    PubMed

    Tao, Yinying; Carta, Giorgio; Ferreira, Gisela; Robbins, David

    2011-03-18

    Single and multicomponent batch adsorption kinetics were obtained for deamidated mAb variants on two commercial cation exchangers, one with an open macroporous structure--UNOsphere S--and the other with charged dextran grafts--Capto S. The adsorption kinetics for the macroporous matrix was found to be controlled largely by pore diffusion. The effective diffusivity estimated from single component data was a fraction of the mAb free solution diffusivity, and its value could be used to accurately predict the adsorption kinetics for two- and three-component systems. In this case, when two or more variants were adsorbed simultaneously, both experimental and predicted results showed a temporary overshoot of the amount adsorbed above the equilibrium value for the more deamidated variant followed by a gradual approach to equilibrium. Adsorption rates on the dextran grafted material were much faster than those observed for the macroporous matrix for both single component and simultaneous adsorption cases. In this case, no significant overshoot was observed for the more deamidated forms. The Capto S adsorption kinetics could be described well by a diffusion model with an adsorbed phase driving force for single component adsorption and for the simultaneous adsorption of multiple variants. However, this model failed to predict the adsorption kinetics when more deamidated forms pre-adsorbed on the resin were displaced by less deamidated ones. In this case, the kinetics of the displacement process was much slower indicating that the pre-adsorbed components severely hindered transport of the more strongly bound variants. Overall, the results indicate that despite the lower capacity, the macroporous resin may be more efficient in process applications where displacement of one variant by another takes place as a result of the faster and more predictable kinetics.

  19. Nanoscale Imaging of Molecular Adsorption

    DTIC Science & Technology

    1994-06-20

    LiAI2(OH)6 ÷X-.nH20,21 and for synthetic HT-like phases.22 This ordered arrangement is most likely a consequence of coulombic interactions within the...hydroxy-2-methoxy-benzenesulfonic acid (MBSA) on the surface of HT. This compound is of technological interest because of its utility in cosmetics ...J. Amer. Chem. Soc., 115, 11521-11535 (1993). 9 Figure Captions Figure 1: (a) Hexagonal HT crystals adhered to a freshly cleaved mica substrate by

  20. Environmental remediation of heavy metal ions from aqueous solution through hydrogel adsorption: a critical review.

    PubMed

    Muya, Francis Ntumba; Sunday, Christopher Edoze; Baker, Priscilla; Iwuoha, Emmanuel

    2016-01-01

    Heavy metal ions such as Cd(2+), Pb(2+), Cu(2+), Mg(2+), and Hg(2+) from industrial waste water constitute a major cause of pollution for ground water sources. These ions are toxic to man and aquatic life as well, and should be removed from wastewater before disposal. Various treatment technologies have been reported to remediate the potential toxic elements from aqueous media, such as adsorption, precipitation and coagulation. Most of these technologies are associated with some shortcomings, and challenges in terms of applicability, effectiveness and cost. However, adsorption techniques have the capability of effectively removing heavy metals at very low concentration (1-100 mg/L). Various adsorbents have been reported in the literature for this purpose, including, to a lesser extent, the use of hydrogel adsorbents for heavy metal removal in aqueous phase. Here, we provide an in-depth perspective on the design, application and efficiency of hydrogel systems as adsorbents.

  1. Biologically and chemically mediated adsorption and precipitation of phosphorus from wastewater.

    PubMed

    Pratt, Chris; Parsons, Simon A; Soares, Ana; Martin, Ben D

    2012-12-01

    Biologically and chemically mediated adsorption and precipitation processes offer a range of approaches for removing phosphorus (P) from agricultural, domestic and industrial effluents. Technologies implemented at full-scale include filtration by adsorbent media, such as steel slag, and recovery of phosphorus as struvite, which has been successfully commercialised as a fertiliser. Other promising technologies under investigation include P removal by polymers and nanomaterials as well as struvite formation by bacteria. There is a need to focus future research on improving the efficiency of P removal by adsorption and precipitation. This can be achieved by techniques such as regenerating filters, polymers and nanomaterials for renewed P removal. Research is also needed to optimise the fertiliser potential of struvite precipitates.

  2. An overview of landfill leachate treatment via activated carbon adsorption process.

    PubMed

    Foo, K Y; Hameed, B H

    2009-11-15

    Water scarcity and pollution rank equal to climate change as the most urgent environmental issue for the 21st century. To date, the percolation landfill leachate into the groundwater tables and aquifer systems which poses a potential risk and potential hazards towards the public health and ecosystems, remains an aesthetic concern and consideration abroad the nations. Arising from the steep enrichment of globalization and metropolitan growth, numerous mitigating approaches and imperative technologies have currently drastically been addressed and confronted. Confirming the assertion, this paper presents a state of art review of leachate treatment technologies, its fundamental background studies, and environmental implications. Moreover, the key advance of activated carbons adsorption, its major challenges together with the future expectation are summarized and discussed. Conclusively, the expanding of activated carbons adsorption represents a potentially viable and powerful tool, leading to the superior improvement of environmental conservation.

  3. Water adsorption constrained Frenkel-Halsey-Hill adsorption activation theory: Montmorillonite and illite clays

    NASA Astrophysics Data System (ADS)

    Hatch, C. D.; Greenaway, A.; Christie, M. J.; Baltrusaitis, J.

    2013-12-01

    Recently, fresh, unprocessed mineral aerosol has been found to contribute to the number of available cloud condensation nuclei (CCN) and cloud droplets in the atmosphere due to the effect of water adsorption on CCN activation. The work described here uses experimental water adsorption measurements on montmorillonite and illite clay to determine empirical adsorption parameters for a recently derived theoretical framework (Frenkel-Halsey-Hill Activation Theory, FHH-AT) used to calculate CCN activities of clay minerals. Upon fitting the Frenkel-Halsey-Hill (FHH) adsorption model to experimental water adsorption measurements, we find FHH adsorption parameters, AFHH and BFHH, to be 98×22 and 1.79×0.11 for Na-montmorillonite and 75×17 and 1.77×0.11 for illite, respectively. The AFHH and BFHH values obtained for these clays are significantly different from FHH adsorption parameters derived from CCN activation measurements reported previously for similar clay minerals. Differences in FHH adsorption parameters were attributed to the different approaches used, the hydratable nature of the clays and the relative difficulty in measuring CCN activation of hydratable clays due to relatively long adsorption and desorption equilibration times. However, despite these differences, the calculated CCN activities of montmorillonite and illite are quite similar and are in excellent agreement with experimental CCN activation measurements reported previously for similar clays. The different FHH adsorption parameters, however, translate to lower sc-Ddry CCN activation curve exponents (xFHH = -0.61 and -0.64 for montmorillonite and illite, respectively) than have been reported previously. The lower exponent suggests that the CCN activity of hydratable clay aerosol is less sensitive to changes in dry particle diameter (Ddry) and the hygroscopicity parameter exhibits a broader variability with Ddry compared to more soluble aerosols. This study illustrates that FHH-AT using adsorption

  4. Adsorption Dynamics Of Water On The Surface Of TiO2 (110)

    NASA Astrophysics Data System (ADS)

    Bundaleski, B.; Silva, A. G.; Schröder, U.; Moutinho, A. M. C.; Teodoro, O. M. N. D.

    2010-07-01

    Rutile titanium dioxide TiO2 is used in a number of technological areas. Therefore, in surface science, it has become the most studied oxide surface, and it is generally used to model the TiO2 catalytic properties under ultra high vacuum conditions. While water adsorption on rutile TiO2 (110) has been mainly investigated using scanning tunnelling spectroscopy (STM), we use here a different approach based on the work function spectroscopy (WF): water adsorption induces formation of a dipole layer which locally changes the work function. The change can be experimentally monitored by the onset shift of the energy spectrum of secondary electrons. Although X-ray photoelectron spectroscopy is not sensitive enough to monitor water adsorption on TiO2 having low defect concentration, WF results clearly show the work function change which is undoubtedly attributed to the water adsorption. These measurements were done for different water vapour pressures, exposure times, sample temperatures and general surface conditions. Time evolution of the work function change, together with that of the H2O partial pressure, enable us to successfully model the adsorption dynamics and help us understand the observed results. This analysis clearly shows existence of at least three different adsorption mechanisms. The interplay between them governs the measured time evolution of the work function change. Their relative contributions depend on the surface temperature and, presumably, its topography. These results will be discussed in the light of several recent experimental (mainly using STM) and theoretical studies of this system done by other authors.

  5. Trimodal nanoporous silica as a support for amine-based CO2 adsorbents: Improvement in adsorption capacity and kinetics

    NASA Astrophysics Data System (ADS)

    Chen, Chao; Bhattacharjee, Samiran

    2017-02-01

    A trimodal nanoporous silica (TS) having unique trimodal pore structure viz., internal mesopores, textural mesopores and interconnected macropores, has been functionalized with amine using two different methods covalent grafting and wet impregnation. Both were studied as nanocomposite sorbents for CO2 capture. The effects of the amine loading, immobilization processes and the type of support were investigated. Commercially available silica gel (SG) with a purely mesoporous structure was studied as the support for the amine in order to compare differences in pore structure and amine loading with differences in CO2 adsorption capacity and kinetics. Amine-grafted TS exhibited much faster CO2 adsorption kinetics at 35 °C than amine-grafted SG. At the same amine loading, amine-impregnated TS showed higher CO2 adsorption capacity and faster CO2 adsorption kinetics than amine-impregnated SG. The CO2 adsorption capacity of amine-impregnated TS increased as the amine loading increased until 70%, with the highest value of 172 mg/g, while the amine-impregnated SG reached the highest CO2 adsorption capacity of only 78 mg/g at 40% amine loading. More importantly, amine-impregnated as-prepared TS exhibited even higher CO2 capture capacity than amine-impregnated TS when the amine loading was below 60%. Results suggest that amine-modified trimodal nanoporous silica sorbents meet the challenges of current CO2 capture technology.

  6. Molecular-level understanding of the adsorption mechanism of a graphite-binding peptide at the water/graphite interface.

    PubMed

    Penna, M J; Mijajlovic, M; Tamerler, C; Biggs, M J

    2015-07-14

    The association of proteins and peptides with inorganic material has vast technological potential. An understanding of the adsorption of peptides at liquid/solid interfaces on a molecular-level is fundamental to fully realising this potential. Combining our prior work along with the statistical analysis of 100+ molecular dynamics simulations of adsorption of an experimentally identified graphite binding peptide, GrBP5, at the water/graphite interface has been used here to propose a model for the adsorption of a peptide at a liquid/solid interface. This bottom-up model splits the adsorption process into three reversible phases: biased diffusion, anchoring and lockdown. Statistical analysis highlighted the distinct roles played by regions of the peptide studied here throughout the adsorption process: the hydrophobic domain plays a significant role in the biased diffusion and anchoring phases suggesting that the initial impetus for association between the peptide and the interface may be hydrophobic in origin; aromatic residues dominate the interaction between the peptide and the surface in the adsorbed state and the polar region in the middle of the peptide affords a high conformational flexibility allowing strongly interacting residues to maximise favourable interactions with the surface. Reversible adsorption was observed here, unlike in our prior work focused on a more strongly interacting surface. However, this reversibility is unlikely to be seen once the peptide-surface interaction exceeds 10 kcal mol(-1).

  7. A biocompatible and novelly-defined Al-HAP adsorption membrane for highly effective removal of fluoride from drinking water.

    PubMed

    He, Junyong; Chen, Kai; Cai, Xingguo; Li, Yulian; Wang, Chengming; Zhang, Kaisheng; Jin, Zhen; Meng, Fanli; Wang, Xuguang; Kong, Lingtao; Liu, Jinhuai

    2017-03-15

    A biocompatible and novelly-defined adsorption membrane for rapid removal of fluoride was prepared. Both adsorption and membrane techniques were used in this research. Al(OH)3 nanoparticles modified hydroxyapatite (Al-HAP) nanowires were developed and made into Al-HAP membrane. The adsorption data of Al-HAP adsorbent could be well described by Freundlich isotherm model while the adsorption kinetic followed pseudo-second-order model. The maximum of adsorption capacity was 93.84mg/g when the fluoride concentration was 200mg/L. The adsorption mechanism was anion exchanges and electrostatic interactions. The contribution rates of HAP nanowires and Al(OH)3 nanoparticles in fluoride removal were 36.70% and 63.30%, respectively. The fixed-bed column test demonstrate that the Al-HAP was biocompatible and in a good stability during the process of water treatment. The fluoride removal abilities of Al-HAP membrane with 0.3mm thickness could reach 1568L/m(2) when fluoride concentrations were 5mg/L. This study indicated that the Al-HAP membrane could be developed into a very viable technology for highly effective removal of fluoride from drinking water.

  8. The adsorption of HCl on volcanic ash

    NASA Astrophysics Data System (ADS)

    Gutiérrez, Xochilt; Schiavi, Federica; Keppler, Hans

    2016-03-01

    Understanding the interaction between volcanic gases and ash is important to derive gas compositions from ash leachates and to constrain the environmental impact of eruptions. Volcanic HCl could potentially damage the ozone layer, but it is unclear what fraction of HCl actually reaches the stratosphere. The adsorption of HCl on volcanic ash was therefore studied from -76 to +150 °C to simulate the behavior of HCl in the dilute parts of a volcanic plume. Finely ground synthetic glasses of andesitic, dacitic, and rhyolitic composition as well as a natural obsidian from Vulcano (Italy) served as proxies for fresh natural ash. HCl adsorption is an irreversible process and appears to increase with the total alkali content of the glass. Adsorption kinetics follow a first order law with rate constants of 2.13 ṡ10-6 s-1 to 1.80 ṡ10-4 s-1 in the temperature range investigated. For dacitic composition, the temperature and pressure dependence of adsorption can be described by the equation ln ⁡ c = 1.26 + 0.27 ln ⁡ p - 715.3 / T, where c is the surface concentration of adsorbed HCl in mg/m2, T is temperature in Kelvin, and p is the partial pressure of HCl in mbar. A comparison of this model with a large data set for the composition of volcanic ash suggests that adsorption of HCl from the gas phase at relatively low temperatures can quantitatively account for the majority of the observed Cl concentrations. The model implies that adsorption of HCl on ash increases with temperature, probably because of the increasing number of accessible adsorption sites. This temperature dependence is opposite to that observed for SO2, so that HCl and SO2 are fractionated by the adsorption process and the fractionation factor changes by four orders of magnitude over a temperature range of 250 K. The assumption of equal adsorption of different species is therefore not appropriate for deriving volcanic gas compositions from analyses of adsorbates on ash. However, with the experimental

  9. Kinetic and thermodynamic studies of sulforaphane adsorption on macroporous resin.

    PubMed

    Yuanfeng, Wu; Lei, Zhang; Jianwei, Mao; Shiwang, Liu; Jun, Huang; Yuru, You; Lehe, Mei

    2016-08-15

    The adsorption equilibrium, kinetic and thermodynamic of sulforaphane (SF) adsorption onto macroporous resin in aqueous phase were studied. The SP850 resin was screened as the appropriate resin for SF purification. From the equilibrium studies, the Redlich-Peterson model was found to be the best for description of the adsorption behavior of SF onto SP850 resin, followed by the Freundlich model and the Langmuir model. Batch equilibrium experiments demonstrated that, in the examined temperature range, the equilibrium adsorption capacity of SP850 resin decreased with increasing adsorption temperature. Thermodynamics studies indicated that the adsorption of SF was a physical, exothermic, and spontaneous process. The adsorption kinetics revealed that the pseudo-second-order kinetic model was suitable to characterize the kinetics of adsorption of SF onto SP850. Finally, the intra-particle diffusion model demonstrated that SF diffused quickly into macropores, and that diffusion slowed down in the meso- and micropores.

  10. The Calculation of Adsorption Isotherms from Chromatographic Peak Shapes

    ERIC Educational Resources Information Center

    Neumann, M. G.

    1976-01-01

    Discusses the relationship between adsorption isotherms and elution peak shapes in gas chromatography, and describes a laboratory experiment which involves the adsorption of hexane, cyclohexane, and benzene on alumina at different temperatures. (MLH)

  11. Adsorption ability comparison of plasma proteins on amorphous carbon surface

    NASA Astrophysics Data System (ADS)

    Takeda, Aoi; Akasaka, Hiroki; Ohshio, Shigeo; Toda, Ikumi; Nakano, Masayuki; Saitoh, Hidetoshi

    2012-11-01

    To understand why amorphous carbon (a-C:H) film shows antithrombogenicity, an adsorption ability of plasma proteins on a-C:H surface was investigated. Protein adsorption is the initial process of clot formation. The protein adsorption ability on a-C:H film surface was compared by the detection using the surface plasmon resonance (SPR) phenomenon to estimate the protein adsorption. The protein adsorption abilities of a fibrinogen (Fib) and a human γ-globulin (HGG) were estimated by the SPR method using a multilayer structure of a-C:H/Au/Cr/glass. Although the adsorption of HGG for a-C:H was saturated at 32 μM in HGG concentration, the adsorption of Fib was not saturated under the detection limit of this method. These results indicated that the adsorption ability to the a-C:H film surface of Fib was higher than HGG.

  12. In vitro adsorption of tilidine HCl by activated charcoal.

    PubMed

    Cordonnier, J A; Van den Heede, M A; Heyndrickx, A M

    In vitro studies were carried out in order to determine the adsorption of tilidine HCl, a narcotic analgesic, by activated charcoal (max. adsorption capacity 185.5 mg/g of charcoal). The path of the adsorption isotherms at pH 1.2 and 7.5 suggests that the in vivo adsorption of tilidine HCl may be increased when the drug passes from the stomach to the intestine, unless the intestinal content exerts a displacing effect. Nevertheless, the adsorption was dependent on the quantity of activated charcoal used, becoming more complete when the quantity of activated charcoal was increased. The effects of additives on the adsorption capacity of activated charcoal were also investigated in vitro. Ethanol, sorbitol and sucrose significantly reduced drug adsorption, while cacao powder, milk and starch had no effect on tilidine adsorption. At an acid pH, Federa Activated Charcoal significantly adsorbed more drug than either Norit A or Activated Charcoal Merck.

  13. Competitive adsorption of VOCcs and BOM: Oxic and anoxic environments

    SciTech Connect

    Sorial, G.A.; Papadimas, S.P.; Suidan, M.T.; Speth, T.F.

    1994-01-01

    The effect of the presence of molecular oxygen on the adsorption of volatile organic compounds (VOCs) in distilled Milli-Q water and in water supplemented with background organic matter (BOM) is evaluated. Experiments are conducted under conditions where molecular oxygen is present in the test environment (oxic adsorption), and where oxygen is absent from the test environment (anoxic adsorption). Adsorption isotherms for tetrachloroethylene (PCE) and trichloroethylene (TCE) in Milli-Q water showed no impact of the presence of oxygen on their adsorption behavior, while adsorption isotherms for cis-1,2-dichloroethylene (DCE) showed higher capacities under toxic conditions. The Ideal Adsorbed Solution Theory (IAST) successfully predicted the VOCs anoxic adsorption isotherms in BOM. However, the IAST model did not predict the VOCs oxic adsorption isotherms in BOM.

  14. IMPACT OF OXYGEN MEDIATED OXIDATIVE COUPLING ON ADSORPTION KINETICS

    EPA Science Inventory

    The presence of molecular oxygen in the test environment promotes oxidative coupling (polymer formation) of phenolic compounds on the surface of granular activated carbon (GAC). Both adsorption equilibria and adsorption kinetics are affected by these chemical reactions. Lack of...

  15. Adsorption of thorium from aqueous solutions by perlite.

    PubMed

    Talip, Z; Eral, M; Hiçsönmez, U

    2009-02-01

    The use of expanded perlite for the adsorption of thorium from aqueous solution by batch technique is presented. The effects of particle size, pH of the solution, initial thorium concentration, shaking time, V/m ratio and temperature were determined. It was found that the adsorption capacity increases by the increase in the pH of the suspensions. The rate of thorium adsorption on expanded perlite was observed to be fast in the first hour of the reaction time. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models and the adsorption experiments conducted at 30 +/- 1 degrees C showed that the adsorption isotherms correlated well with the Langmuir model. From the adsorption data, thermodynamic parameters such as DeltaG(o), DeltaH(o) and DeltaS(o) were calculated as a function of temperature.

  16. Electrical swing adsorption gas storage and delivery system

    DOEpatents

    Judkins, Roddie R.; Burchell, Timothy D.

    1999-01-01

    Systems and methods for electrical swing natural gas adsorption are described. An apparatus includes a pressure vessel; an electrically conductive gas adsorptive material located within the pressure vessel; and an electric power supply electrically connected to said adsorptive material. The adsorptive material can be a carbon fiber composite molecular sieve (CFCMS). The systems and methods provide advantages in that both a high energy density and a high ratio of delivered to stored gas are provided.

  17. Carbon dioxide separation using adsorption with steam regeneration

    DOEpatents

    Elliott, Jeannine Elizabeth; Copeland, Robert James; Leta, Daniel P.; McCall, Patrick P.; Bai, Chuansheng; DeRites, Bruce A.

    2016-11-29

    A process for separating a carbon dioxide from a gas stream is disclosed. The process can include passing the gas stream over a sorbent that adsorbs the carbon dioxide by concentration swing adsorption and adsorptive displacement. The sorbent can be regenerated and the carbon dioxide recaptured by desorbing the carbon dioxide from the sorbent using concentration swing adsorption and desorptive displacement. A carbon dioxide separation system is also disclosed. Neither the system nor the process rely on temperature swing or pressure swing adsorption.

  18. Electrical swing adsorption gas storage and delivery system

    DOEpatents

    Judkins, R.R.; Burchell, T.D.

    1999-06-15

    Systems and methods for electrical swing natural gas adsorption are described. An apparatus includes a pressure vessel; an electrically conductive gas adsorptive material located within the pressure vessel; and an electric power supply electrically connected to said adsorptive material. The adsorptive material can be a carbon fiber composite molecular sieve (CFCMS). The systems and methods provide advantages in that both a high energy density and a high ratio of delivered to stored gas are provided. 5 figs.

  19. Factors affecting the adsorption of xenon on activated carbon

    SciTech Connect

    Underhill, D.W.; DiCello, D.C.; Scaglia, L.A.; Watson, J.A.

    1986-08-01

    The presence of water vapor was found to interfere strongly with the dynamic adsorption of /sup 133/Xe on coconut-base activated charcoal. The percent loss in the xenon adsorption coefficient was similar to values reported earlier for the adsorption of krypton on humidified charcoal. Attempts to increase the adsorption of xenon by (a) using a petroleum-based adsorbent with an extremely high surface area and (b) by impregnation of the adsorbent with iodine were not successful.

  20. Adsorption kinetics of laterally and polarly flagellated Vibrio.

    PubMed Central

    Belas, M R; Colwell, R R

    1982-01-01

    The adsorption of laterally and polarly flagellated bacteria to chitin was measured, and from the data obtained, a modified Langmuir adsorption isotherm was derived. Results indicated that the adsorption of laterally flagellated Vibrio parahaemolyticus follows the Langmuir adsorption isotherm, a type of adsorption referred to as surface saturation kinetics, when conditions are favorable for the production of lateral flagella. When conditions were not favorable for the production of lateral flagella, bacterial adsorption did not follow the Langmuir adsorption isotherm; instead, proportional adsorption kinetics were observed. The adsorption of some polarly flagellated bacteria exhibited surface saturation kinetics. However, the binding index (the product of the number of binding sites and bacterial affinity to the surface) of polarly flagellated bacteria differed significantly from that of laterally flagellated bacteria, suggesting that polarly flagellated bacteria adsorb to chitin by a different mechanism from that used by the laterally flagellated bacteria. From the results of dual-label adsorption competition experiments, in which polarly flagellated V. cholerae competed with increasing concentrations of laterally flagellated V. parahaemolyticus, it was observed that laterally flagellated bacteria inhibited the adsorption of polarly flagellated bacteria. In contrast, polarly flagellated bacteria enhanced the adsorption of V. cholerae. In competition experiments, where V. parahaemolyticus competed against increasing concentrations of other bacteria, polarly flagellated bacteria enhanced V. parahaemolyticus adsorption significantly, whereas laterally flagellated bacteria only slightly enhanced the process. The direct correlation observed between surface saturation kinetics, the production of lateral flagella, and the ability of laterally flagellated bacteria to inhibit the adsorption of polarly flagellated bacteria suggests that lateral flagella represent a

  1. Zinc modulates thrombin adsorption to fibrin

    SciTech Connect

    Hopmeier, P.; Halbmayer, M.; Fischer, M.; Marx, G. )

    1990-05-01

    Human thrombin with high affinity to Sepharose insolubilized fibrin monomers (high-affinity thrombin) was used to investigate the effect of Zn(II) on the thrombin adsorption to fibrin. Results showed that at Zn(II) concentrations exceeding 100 mumols/l, thrombin binding to fibrin was decreased concomitant with the Zn(II) concentration and time; at lower Zn(II) concentrations, thrombin adsorption was enhanced. Experimental results were identical by using 125I-labelled high-affinity alpha-thrombin or by measuring the thrombin activity either by chromogenic substrate or by a clotting time method. In contrast, Ca(II) alone (final conc. 3 mmol/l) or in combination with Zn(II) was not effective. However, at higher Ca(II) concentrations (7.5-15 mmol/l), thrombin adsorption was apparently decreased. Control experiments revealed that Zn(II) had no impact on the clottability of fibrinogen, and that the results of the experiments with Ca(II) were not altered by possible cross-linking of fibrin. We conclude that unlike Ca(II), Zn(II) is highly effective in modulating thrombin adsorption to fibrin.

  2. Asphaltene adsorption and desorption from mineral surfaces

    SciTech Connect

    Dubey, S.T. ); Waxman, M.H.

    1991-02-01

    This paper reports results of asphaltene adsorption/desorption on clay minerals, silica, and carbonates. It also describes the effect of adsorbed asphaltenes on rock wettability and a screening pyrolysis-flame-ionization-detection (P-FID) test to evaluate the ability of solvents to remove asphaltene from kaolin and formation core material.

  3. Adsorption modeling for off-gas treatment

    SciTech Connect

    Ladshaw, A.; Sharma, K.; Yiacoumi, S.; Tsouris, C.; De Paoli, D.W.

    2013-07-01

    Off-gas generated from the reprocessing of used nuclear fuel contains a mixture of several radioactive gases including {sup 129}I{sub 2}, {sup 85}Kr, HTO, and {sup 14}CO{sub 2}. Over the past few decades, various separation and recovery processes have been studied for capturing these gases. Adsorption data for gaseous mixtures of species can be difficult to determine experimentally. Therefore, procedures capable of predicting the adsorption behavior of mixtures need to be developed from the individual isotherms of each of the pure species. A particular isotherm model of interest for the pure species is the Generalized Statistical Thermodynamic Adsorption isotherm. This model contains an adjustable number of parameters and will therefore describe a wide range of adsorption isotherms for a variety of components. A code has been developed in C++ to perform the non-linear regression analysis necessary for the determination of the isotherm parameters, as well as the least number of parameters needed to describe an entire set of data. (authors)

  4. Modeling adsorption with lattice Boltzmann equation

    PubMed Central

    Guo, Long; Xiao, Lizhi; Shan, Xiaowen; Zhang, Xiaoling

    2016-01-01

    The research of adsorption theory has recently gained renewed attention due to its critical relevance to a number of trending industrial applications, hydrogen storage and shale gas exploration for instance. The existing theoretical foundation, laid mostly in the early twentieth century, was largely based on simple heuristic molecular interaction models and static interaction potential which, although being insightful in illuminating the fundamental mechanisms, are insufficient for computations with realistic adsorbent structure and adsorbate hydrodynamics, both critical for real-life applications. Here we present and validate a novel lattice Boltzmann model incorporating both adsorbate-adsorbate and adsorbate-adsorbent interactions with hydrodynamics which, for the first time, allows adsorption to be computed with real-life details. Connection with the classic Ono-Kondo lattice theory is established and various adsorption isotherms, both within and beyond the IUPAC classification are observed as a pseudo-potential is varied. This new approach not only enables an important physical to be simulated for real-life applications, but also provides an enabling theoretical framework within which the fundamentals of adsorption can be studied. PMID:27256325

  5. Adsorption of carboxymethyl cellulose on alumina particles.

    PubMed

    Zhivkov, Alexandar M; Hristov, Rosen P

    2015-06-01

    The polyelectrolyte adsorption on colloid particles is often used for stabilization or flocculation of water suspensions. The aim of this work is to study the adsorption of carboxymethyl cellulose (CMC) on alumina (γ-Al2O3) colloid particles. The particles and polymer are chosen because of the capability of the metal-oxide ampholyte surface and the weak polyelectrolytes to alter their charge by pH. The measurements are done at pH 6.0 where the CMC carboxylic gropes are almost fully dissociated and the alumina surface is positively charged. The high linear charge density of the polyelectrolyte chain provides Na(+) counterions condensation on the COO(-) groups. The main employed method is the electric light scattering based on particle orientation in sinusoidal electric field. The electric polarizability and the relaxation time after field switching off (both depending on the particle charge and size) are used as criteria for polymer adsorption and particle aggregation. Micro-electrophoresis is applied as additional techniques indicating the sign and density of the surface charge. The results obtained give the conditions (time dependence, particle and polymer concentrations) where the CMC adsorption is complete and the suspension is stable.

  6. Adsorption of diblock polypeptides on polystyrene latex.

    PubMed

    Jain, Ritesh; Forciniti, Daniel

    2012-10-30

    The adsorption of peptides at solid/liquid interfaces is affected by peptide/surface and peptide/peptide hydrophobic and electrostatic forces. Three diblock copolypeptides and two homopeptides were adsorbed on poly(styrene) nanospheres from water, water/methanol, and water/glycerol mixtures at different pH's to study both of these effects. Peptides with one hydrophilic (glutamic acid or lysine) and one nonpolar block (alanine) or with both hydrophilic blocks with opposite charges (glutamic acid and lysine) were chemically synthesized and used as adsorbates in this study. The amount adsorbed was determined, and dynamic light scattering (DLS) was used to measure the adsorbed layer thickness. It was found that peptide/surface and peptide/peptide electrostatic interactions dominate the adsorption process. Hydrophobic forces also play a role, but secondary to electrostatic forces. Positively charged blocks show high affinity for the surface, whereas negatively charged blocks were excluded from it. Poly(Lys) has the highest affinity by the surface, while (Glu)(14)-b-(Ala)(5) has the lowest. Adsorption of all peptides was inhibited by methanol and promoted by glycerol. The adsorption for (Lys)(5)-b-(Glu)(6) was extremely sensitive to pH, irrespective of cosolvent, whereas the thickness for (Lys)(30)-b-(Ala)(41) was sensitive to pH as well as cosolvent. Aggregation was observed in the presence of the nanosurfaces but not in the bulk peptides under some pH and solvent conditions.

  7. Adsorption of Ions at Uncharged Insoluble Monolayers.

    PubMed

    Peshkova, Tatyana V; Minkov, Ivan L; Tsekov, Roumen; Slavchov, Radomir I

    2016-09-06

    A method is proposed for the experimental determination of the adsorption of inorganic electrolytes at a surface covered with insoluble surfactant monolayer. This task is complicated by the fact that the change of the salt concentration alters both chemical potentials of the electrolyte and the surfactant. Our method resolves the question by combining data for the surface pressure versus area of the monolayer at several salt concentrations with data for the equilibrium spreading pressure of crystals of the surfactant (used to fix a standard state). We applied the method to alcohols spread at the surface of concentrated halide solutions. The measured salt adsorption is positive and has nonmonotonic dependence on the area per surfactant molecule. For the liquid expanded film, depending on the concentration, there is one couple of ions adsorbed per each 3-30 surfactant molecules. We analyzed which ion, the positive or the negative, stands closer to the surface, by measuring the effect of NaCl on the Volta potential of the monolayer. The potentiometric data suggest that Na(+) is specifically adsorbed, while Cl(-) remains in the diffuse layer, i.e., the surface is positively charged. The observed reverse Hofmeister series of the adsorptions of NaF, NaCl, and NaBr suggests the same conclusion holds for all these salts. The force that causes the adsorption of Na(+) seems to be the interaction of the ion with the dipole moment of the monolayer.

  8. Fluorocarbon adsorption in hierarchical porous frameworks

    SciTech Connect

    Motkuri, RK; Annapureddy, HVR; Vijaykumar, M; Schaef, HT; Martin, PF; McGrail, BP; Dang, LX; Krishna, R; Thallapally, PK

    2014-07-09

    Metal-organic frameworks comprise an important class of solid-state materials and have potential for many emerging applications such as energy storage, separation, catalysis and bio-medical. Here we report the adsorption behaviour of a series of fluorocarbon derivatives on a set of microporous and hierarchical mesoporous frameworks. The microporous frameworks show a saturation uptake capacity for dichlorodifluoromethane of >4 mmol g(-1) at a very low relative saturation pressure (P/P-o) of 0.02. In contrast, the mesoporous framework shows an exceptionally high uptake capacity reaching >14 mmol g(-1) at P/P-o of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption is found to generally correlate with the polarizability and boiling point of the refrigerant, with dichlorodifluoromethane >chlorodifluoromethane >chlorotrifluoromethane >tetrafluoromethane >methane. These results suggest the possibility of exploiting these sorbents for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling.

  9. Modeling adsorption with lattice Boltzmann equation.

    PubMed

    Guo, Long; Xiao, Lizhi; Shan, Xiaowen; Zhang, Xiaoling

    2016-06-03

    The research of adsorption theory has recently gained renewed attention due to its critical relevance to a number of trending industrial applications, hydrogen storage and shale gas exploration for instance. The existing theoretical foundation, laid mostly in the early twentieth century, was largely based on simple heuristic molecular interaction models and static interaction potential which, although being insightful in illuminating the fundamental mechanisms, are insufficient for computations with realistic adsorbent structure and adsorbate hydrodynamics, both critical for real-life applications. Here we present and validate a novel lattice Boltzmann model incorporating both adsorbate-adsorbate and adsorbate-adsorbent interactions with hydrodynamics which, for the first time, allows adsorption to be computed with real-life details. Connection with the classic Ono-Kondo lattice theory is established and various adsorption isotherms, both within and beyond the IUPAC classification are observed as a pseudo-potential is varied. This new approach not only enables an important physical to be simulated for real-life applications, but also provides an enabling theoretical framework within which the fundamentals of adsorption can be studied.

  10. Adsorption of dyes on Sahara desert sand.

    PubMed

    Varlikli, Canan; Bekiari, Vlasoula; Kus, Mahmut; Boduroglu, Numan; Oner, Ilker; Lianos, Panagiotis; Lyberatos, Gerasimos; Icli, Siddik

    2009-10-15

    Sahara desert sand (SaDeS) was employed as a mineral sorbent for retaining organic dyes from aqueous solutions. Natural sand has demonstrated a strong affinity for organic dyes but significantly lost its adsorption capacity when it was washed with water. Therefore, characterization of both natural and water washed sand was performed by XRD, BET, SEM and FTIR techniques. It was found that water-soluble kyanite, which is detected in natural sand, is the dominant factor affecting adsorbance of cationic dyes. The sand adsorbs over 75% of cationic dyes but less than 21% for anionic ones. Among the dyes studied, Methylene Blue (MB) demonstrated the strongest affinity for Sahara desert sand (Q(e)=11.98 mg/g, for initial dye solution concentration 3.5 x 10(-5)mol/L). The effects of initial dye concentration, the amount of the adsorbent, the temperature and the pH of the solution on adsorption capacity were tested by using Methylene Blue as model dye. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were applied. It was concluded that adsorption of Methylene Blue on Sahara desert sand followed pseudo-second order kinetics. Gibbs free energy, enthalpy change and entropy change were calculated and found -6411 J/mol, -30360 J/mol and -76.58 J/mol K, respectively. These values indicate that the adsorption is an exothermic process and has a spontaneous nature at low temperatures.

  11. Critical analysis of adsorption data statistically

    NASA Astrophysics Data System (ADS)

    Kaushal, Achla; Singh, S. K.

    2016-09-01

    Experimental data can be presented, computed, and critically analysed in a different way using statistics. A variety of statistical tests are used to make decisions about the significance and validity of the experimental data. In the present study, adsorption was carried out to remove zinc ions from contaminated aqueous solution using mango leaf powder. The experimental data was analysed statistically by hypothesis testing applying t test, paired t test and Chi-square test to (a) test the optimum value of the process pH, (b) verify the success of experiment and (c) study the effect of adsorbent dose in zinc ion removal from aqueous solutions. Comparison of calculated and tabulated values of t and χ 2 showed the results in favour of the data collected from the experiment and this has been shown on probability charts. K value for Langmuir isotherm was 0.8582 and m value for Freundlich adsorption isotherm obtained was 0.725, both are <1, indicating favourable isotherms. Karl Pearson's correlation coefficient values for Langmuir and Freundlich adsorption isotherms were obtained as 0.99 and 0.95 respectively, which show higher degree of correlation between the variables. This validates the data obtained for adsorption of zinc ions from the contaminated aqueous solution with the help of mango leaf powder.

  12. Adsorption of Ions at Uncharged Insoluble Monolayers

    NASA Astrophysics Data System (ADS)

    Peshkova, T. V.; Minkov, I. L.; Tsekov, R.; Slavchov, R. I.

    2016-08-01

    A method is proposed for the experimental determination of the adsorption of inorganic electrolytes at a surface covered with insoluble surfactant monolayer. This task is complicated by the fact that the change of the salt concentration alters both chemical potentials of the electrolyte and the surfactant. Our method resolves the question by combining data for the surface pressure versus area of the monolayer at several salt concentrations with data for the equilibrium spreading pressure of crystals of the surfactant (used to fix a standard state). We applied the method to alcohols spread at the surface of concentrated halide solutions. The measured salt adsorption is positive and has nonmonotonic dependence on the area per surfactant molecule. For the liquid expanded film, depending on the concentration, there is one couple of ions adsorbed per each 3–30 surfactant molecules. We analyzed which ion, the positive or the negative, stands closer to the surface, by measuring the effect of NaCl on the Volta potential of the monolayer. The potentiometric data suggest that Na+ is specifically adsorbed, while Cl– remains in the diffuse layer, i.e., the surface is positively charged. The observed reverse Hofmeister series of the adsorptions of NaF, NaCl, and NaBr suggests the same conclusion holds for all these salts. The force that causes the adsorption of Na+ seems to be the interaction of the ion with the dipole moment of the monolayer.

  13. CARBON ADSORPTION FOR INDOOR AIR CLEANING

    EPA Science Inventory

    The paper discusses the use of carbon adsorption for indoor air cleaning, focusing on the removal of volatile organic compounds (VOCs) using granular activated carbon (GAC). It addresses GAC performance in two directions. Initially, it presents performance measurements for GAC at...

  14. H2O Adsorption Kinetics on Smectites

    NASA Technical Reports Server (NTRS)

    Zent, Aaron P.; Quinn, Richard C.; Howard, Jeanie; DeVincenzi, Donald L. (Technical Monitor)

    2000-01-01

    The adsorptive equilibration of H2O a with montomorillonite, a smectite clay has been measured. At low temperatures and pressures, equilibration can require many hours, effectively preventing smectites at the martian surface from responding rapidly to diurnal pressure and temperature variations.

  15. ADSORPTION OF ORGANIC CATIONS TO NATURAL MATERIALS

    EPA Science Inventory

    The factors that control the extent of adsorption of amphiphilic organic cations on environmental and pristine surfaces have been studied. The sorbents were kaolinite, montmorillonite, two aquifer materials, and a soil; solutions contained various concentrations of NaCl and CaCl,...

  16. Adsorption Kinetics in Nanoscale Porous Coordination Polymers

    SciTech Connect

    Nune, Satish K.; Thallapally, Praveen K.; McGrail, Benard Peter; Annapureddy, Harsha V. R.; Dang, Liem X.; Mei, Donghai; Karri, Naveen; Alvine, Kyle J.; Olszta, Matthew J.; Arey, Bruce W.; Dohnalkova, Alice

    2015-10-07

    Nanoscale porous coordination polymers were synthesized using simple wet chemical method. The effect of various polymer surfactants on colloidal stability and shape selectivity was investigated. Our results suggest that the nanoparticles exhibited significantly improved adsorption kinetics compared to bulk crystals due to decreased diffusion path lengths and preferred crystal plane interaction.

  17. Fluorocarbon adsorption in hierarchical porous frameworks

    NASA Astrophysics Data System (ADS)

    Motkuri, Radha Kishan; Annapureddy, Harsha V. R.; Vijaykumar, M.; Schaef, H. Todd; Martin, Paul F.; McGrail, B. Peter; Dang, Liem X.; Krishna, Rajamani; Thallapally, Praveen K.

    2014-07-01

    Metal-organic frameworks comprise an important class of solid-state materials and have potential for many emerging applications such as energy storage, separation, catalysis and bio-medical. Here we report the adsorption behaviour of a series of fluorocarbon derivatives on a set of microporous and hierarchical mesoporous frameworks. The microporous frameworks show a saturation uptake capacity for dichlorodifluoromethane of >4 mmol g-1 at a very low relative saturation pressure (P/Po) of 0.02. In contrast, the mesoporous framework shows an exceptionally high uptake capacity reaching >14 mmol g-1 at P/Po of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption is found to generally correlate with the polarizability and boiling point of the refrigerant, with dichlorodifluoromethane >chlorodifluoromethane >chlorotrifluoromethane >tetrafluoromethane >methane. These results suggest the possibility of exploiting these sorbents for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling.

  18. Visualizing Gas Adsorption on Porous Solids: Four Simple, Effective Demonstrations

    ERIC Educational Resources Information Center

    Cheung, Ocean

    2014-01-01

    Gas adsorption on porous solids is a topic that is often discussed in an undergraduate chemistry or chemical engineering course. The idea of porosity and gas adsorption on a porous solid is usually discussed with adsorption isotherms recorded using commercially available equipment. This discussion can be rather abstract and can be difficult for…

  19. Adsorption of halogenated aliphatic contaminants by graphene nanomaterials.

    PubMed

    Zhou, Yang; Apul, Onur Guven; Karanfil, Tanju

    2015-08-01

    In this study, adsorption of ten environmentally halogenated aliphatic synthetic organic compounds (SOCs) by a pristine graphene nanosheet (GNS) and a reduced graphene oxide (rGO) was examined, and their adsorption behaviors were compared with those of a single-walled carbon nanotube (SWCNT) and a granular activated carbon (GAC). In addition, the impacts of background water components (i.e., natural organic matter (NOM), ionic strength (IS) and pH) on the SOC adsorption behavior were investigated. The results indicated HD3000 and SWCNT with higher microporous volumes exhibited higher adsorption capacities for the selected aliphatic SOCs than graphenes, demonstrating microporosity of carbonaceous adsorbents played an important role in the adsorption. Analysis of adsorption isotherms demonstrated that hydrophobic interactions were the dominant contributor to the adsorption of aliphatic SOCs by graphenes. However, π-π electron donor-acceptor and van der Waals interactions are likely the additional mechanisms contributing to the adsorption of aliphatic SOCs on graphenes. Among the three background solution components examined, NOM showed the most influential effect on adsorption of the selected aliphatic SOCs, while pH and ionic strength had a negligible effects. The NOM competition on aliphatic adsorption was less pronounced on graphenes than SWCNT. Overall, in terms of adsorption capacities, graphenes tested in this study did not exhibit a major advantage over SWCNT and GAC for the adsorption of aliphatic SOCs.

  20. Influence of Soil Solution Salinity on Molybdenum Adsorption by Soils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Molybdenum (Mo) adsorption on five arid-zone soils from California was investigated as a function of equilibrium solution Mo concentration (0-30 mg L-1), solution pH (4-8), and electrical conductivity (EC = 0.3 or 8 dS m-1). Molybdenum adsorption decreased with increasing pH. An adsorption maximum...

  1. Adsorption isotherm of non-azeotropic solution onto porous adsorbents

    NASA Astrophysics Data System (ADS)

    Bono, A.; Ramlan, N. A.; Anisuzzaman, S. M.; Chu, C. M.; Farm, Y. Y.

    2016-06-01

    Adsorption isotherm is essential component in the understanding of the adsorption process. Several methods of the measurements, analysis and interpretation of adsorption from solution have been reported in the literature. Most of the measurements of adsorption isotherm from solution were involved the measurement of excess isotherm conducted at low region of sorbates concentration. Direct interpretation of excess adsorption isotherm as adsorption isotherm is always been practice. Therefore, in this work a study on the measurement of the adsorption isotherm from solution of non-azeotropic organic solvent mixture onto porous adsorbents for whole range of liquid concentration was conducted. The study included the measurement of excess adsorption isotherm using conventional technique. Theoretical analysis and interpretation of adsorption isotherm from the excess isotherm were conducted using Pseudo Ideal Adsorption, Gibbs Dividing Plane Model and Langmuir-Fruendlich binary isotherm model. For organic solvents, acetone and propanol were chosen as the adsorbates due to the non-azeotropic properties in the mixture. Activated carbon and silicalite were chosen as adsorbents due to the different in their porosity such as macro porous and micro porous structure. The result of the study has revealed that the adsorption isotherm of non-azeotropic mixture onto activated carbon and silicalite can be interpreted as monolayer type of adsorption.

  2. How specific halide adsorption varies hydrophobic interactions.

    PubMed

    Stock, Philipp; Müller, Melanie; Utzig, Thomas; Valtiner, Markus

    2016-03-11

    Hydrophobic interactions (HI) are driven by the water structure around hydrophobes in aqueous electrolytes. How water structures at hydrophobic interfaces and how this influences the HI was subject to numerous studies. However, the effect of specific ion adsorption on HI and hydrophobic interfaces remains largely unexplored or controversial. Here, the authors utilized atomic force microscopy force spectroscopy at well-defined nanoscopic hydrophobic interfaces to experimentally address how specific ion adsorption of halide ions as well as NH4 (+), Cs(+), and Na(+) cations alters interaction forces across hydrophobic interfaces. Our data demonstrate that iodide adsorption at hydrophobic interfaces profoundly varies the hydrophobic interaction potential. A long-range and strong hydration repulsion at distances D > 3 nm, is followed by an instability which could be explained by a subsequent rapid ejection of adsorbed iodides from approaching hydrophobic interfaces. In addition, the authors find only a weakly pronounced influence of bromide, and as expected no influence of chloride. Also, all tested cations do not have any significant influence on HI. Complementary, x-ray photoelectron spectroscopy and quartz-crystal-microbalance with dissipation monitoring showed a clear adsorption of large halide ions (Br(-)/I(-)) onto hydrophobic self-assembled monolayers (SAMs). Interestingly, iodide can even lead to a full disintegration of SAMs due to specific and strong interactions of iodide with gold. Our data suggest that hydrophobic surfaces are not intrinsically charged negatively by hydroxide adsorption, as it was generally believed. Hydrophobic surfaces rather interact strongly with negatively charged large halide ions, leading to a surface charging and significant variation of interaction forces.

  3. Adsorption Model for Off-Gas Separation

    SciTech Connect

    Veronica J. Rutledge

    2011-03-01

    The absence of industrial scale nuclear fuel reprocessing in the U.S. has precluded the necessary driver for developing the advanced simulation capability now prevalent in so many other countries. Thus, it is essential to model complex series of unit operations to simulate, understand, and predict inherent transient behavior and feedback loops. A capability of accurately simulating the dynamic behavior of advanced fuel cycle separation processes will provide substantial cost savings and many technical benefits. The specific fuel cycle separation process discussed in this report is the off-gas treatment system. The off-gas separation consists of a series of scrubbers and adsorption beds to capture constituents of interest. Dynamic models are being developed to simulate each unit operation involved so each unit operation can be used as a stand-alone model and in series with multiple others. Currently, an adsorption model has been developed in gPROMS software. Inputs include gas stream constituents, sorbent, and column properties, equilibrium and kinetic data, and inlet conditions. It models dispersed plug flow in a packed bed under non-isothermal and non-isobaric conditions for a multiple component gas stream. The simulation outputs component concentrations along the column length as a function of time from which the breakthrough data is obtained. It also outputs temperature along the column length as a function of time and pressure drop along the column length. Experimental data will be input into the adsorption model to develop a model specific for iodine adsorption on silver mordenite as well as model(s) specific for krypton and xenon adsorption. The model will be validated with experimental breakthrough curves. Another future off-gas modeling goal is to develop a model for the unit operation absorption. The off-gas models will be made available via the server or web for evaluation by customers.

  4. Kinetics of phosphate adsorption on goethite: comparing batch adsorption and ATR-IR measurements.

    PubMed

    Luengo, Carina; Brigante, Maximiliano; Antelo, Juan; Avena, Marcelo

    2006-08-15

    The adsorption kinetics of phosphate on goethite has been studied by batch adsorption experiments and by in situ ATR-IR spectroscopy at different pH, initial phosphate concentrations and stirring rates. Batch adsorption results are very similar to those reported by several authors, and show a rather fast initial adsorption taking place in a few minutes followed by a slower process taking place in days or weeks. The adsorption kinetics could be also monitored by integrating the phosphate signals obtained in ATR-IR experiments, and a very good agreement between both techniques was found. At pH 4.5 two surface complexes, the bidentate nonprotonated (FeO)(2)PO(2) and the bidentate protonated (FeO)(2)(OH)PO complexes, are formed at the surface. There are small changes in the relative concentrations of these species as the reaction proceeds, and they seem to evolve in time rather independently. At pH 7.5 and 9 the dominating surface species is (FeO)(2)PO(2), which is accompanied by an extra unidentified species at low concentration. They also seem to evolve independently as the reaction proceeds. The results are consistent with a mechanism that involve a fast adsorption followed by a slow diffusion into pores, and are not consistent with surface precipitation of iron phosphate.

  5. Adsorption of alkyltrimethylammonium bromides at water/alkane interfaces: competitive adsorption of alkanes and surfactants.

    PubMed

    Fainerman, V B; Mucic, N; Pradines, V; Aksenenko, E V; Miller, R

    2013-11-12

    The adsorption of members of the homologous series of alkyl trimethylammonium bromides (C(n)TAB) is studied at water/alkane interfaces by drop profile analysis tensiometry. The results are discussed in terms of a competitive adsorption process of alkane and surfactant molecules. A thermodynamic model, derived originally for the adsorption of surfactant mixtures, is adapted such that it describes a competitive adsorption of the surfactant molecules from the aqueous phase and alkane molecules from the oil phase. This new model involves the interspecies attraction coefficient, which mutually increases the adsorption activities of the alkane and C(n)TAB. The effects of the alkyl chain length n of C(n)TABs and the influence of the number of C atoms in the alkane chain are discussed, and the physical quantities are compared to those determined at the aqueous solution/air interface. The new theoretical model for aqueous solution/oil interfaces is also compared to a theory that does not consider the adsorption of alkane. The proposed new model demonstrates good agreement with the experimental data.

  6. Adsorption of ammonium dinitramide (ADN) from aqueous solutions. 1. Adsorption on powdered activated charcoal.

    PubMed

    Santhosh, G; Venkatachalam, S; Ninan, K N; Sadhana, R; Alwan, S; Abarna, V; Joseph, M A

    2003-03-17

    Investigations on the adsorption of ammonium dinitramide (NH(4)N(NO(2))(2)) (ADN) from aqueous solutions on powdered activated charcoal (PAC) were carried out in order to find out an effective and easier method of separating ADN from aqueous solutions. The effectiveness of PAC in the selective adsorption of ADN from aqueous solutions of ADN (ADN-F) and ADN in presence of sulfate (SO(4)(2-)) and nitrate (NO(3)(-)) ions (ADN-PS) was examined and compared using batch and column methods. The adsorption process follows both Langmuir and Freundlich adsorption isotherms and the isotherm parameters for the models were determined. The observed data favor the formation of monolayer adsorption. The adsorption capacities were found to be 63.3, 119, 105.3 and 82 mg of ADN per g of PAC for ADN-F (batch), ADN-PS (batch), ADN-F (column) and ADN-PS (column), respectively. Break-through curves for ADN-F and ADN-PS were obtained for the optimization of separation of ADN from aqueous solutions. Elution curves were generated for the desorption of ADN from PAC using hot water as eluent.

  7. Effect of Solution Properties on Arsenic Adsorption by Drinking Water Treatment Residuals

    NASA Astrophysics Data System (ADS)

    Nagar, R.; Sarkar, D.; Datta, R.; Sharma, S.

    2005-05-01

    Arsenic (As) is a ubiquitous element in the environment. Higher levels of As in soils may result from various anthropogenic sources such as use of arsenical pesticides, fertilizers, wood preservatives, smelter wastes, and coal combustion. This is of great environmental and human health concern due to the high toxicity and proven carcinogenicity of several arsenical species. Thus there is a need for developing cost effective technologies capable of lowering bioavailable As concentrations in soils to environmentally acceptable levels. In-situ immobilization of metals using inexpensive amendments such as minerals (apatite, zeolite, or clay minerals) or waste by-products (steel shot, beringite, and iron-rich biosolids) to reduce bioavailability is an inexpensive alternative to the more expensive ex-situ remediation methods. One such emerging in-situ technique is the application of drinking water treatment residuals (WTRs). WTRs can be classified as a byproduct of drinking water treatment plants and are generally composed of amorphous Fe/Al oxides, activated C and cationic polymers. WTRs possess amorphous structure and generally have high positive charge. Because As is chemically similar to phosphorus, the oxyanions As (V) and As (III) may have the potential of being retained by the WTRs. Thus, it is hypothesized that WTRs retain As irreversibly, thereby reducing As biavailability. As mobility of arsenic is controlled by adsorption reactions, knowledge of adsorption of As by WTRs is of primary relevance. Although the overall rate of adsorption is dependent on numerous factors, review of the literature indicates that competing ions in solution play an important role in the overall retention of As; however, little work has been conducted to identify which ions provide the most competition. As arsenic adsorption appears to be influenced by the variable pH-dependent charges developed on the soil particle surfaces, the effect of pH is also of critical importance. Hence, the

  8. 76 FR 14038 - TWIC/MTSA Policy Advisory Council; Voluntary Use of TWIC Readers

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ... either (1) comparing the card's internal Federal Agency Smart Card Number to the TSA Cancelled Card List... of transportation security card readers to leverage the full security benefits of the Transportation... to meet existing regulatory requirements for effective (1) identity verification, (2) card...

  9. A Framework and Algorithms for Multivariate Time Series Analytics (MTSA): Learning, Monitoring, and Recommendation

    ERIC Educational Resources Information Center

    Ngan, Chun-Kit

    2013-01-01

    Making decisions over multivariate time series is an important topic which has gained significant interest in the past decade. A time series is a sequence of data points which are measured and ordered over uniform time intervals. A multivariate time series is a set of multiple, related time series in a particular domain in which domain experts…

  10. Natural Minerals Coated by Biopolymer Chitosan: Synthesis, Physicochemical, and Adsorption Properties

    NASA Astrophysics Data System (ADS)

    Budnyak, T. M.; Yanovska, E. S.; Kichkiruk, O. Yu.; Sternik, D.; Tertykh, V. A.

    2016-11-01

    Natural minerals are widely used in treatment technologies as mineral fertilizer, food additive in animal husbandry, and cosmetics because they combine valuable ion-exchanging and adsorption properties together with unique physicochemical and medical properties. Saponite (saponite clay) of the Ukrainian Podillya refers to the class of bentonites, a subclass of layered magnesium silicate montmorillonite. Clinoptilolits are aluminosilicates with carcase structure. In our work, we have coated biopolymer chitosan on the surfaces of natural minerals of Ukrainian origin — Podilsky saponite and Sokyrnitsky clinoptilolite. Chitosan mineral composites have been obtained by crosslinking of adsorbed biopolymer on saponite and clinoptilolite surface with glutaraldehyde. The obtained composites have been characterized by the physicochemical methods such as thermogravimetric/differential thermal analyses (DTA, DTG, TG), differential scanning calorimetry, mass analysis, nitrogen adsorption/desorption isotherms, scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy to determine possible interactions between the silica and chitosan molecule. The adsorption of microquantities of cations Cu(II), Zn(II), Fe(III), Cd(II), and Pb(II) by the obtained composites and the initial natural minerals has been studied from aqueous solutions. The sorption capacities and kinetic adsorption characteristics of the adsorbents were estimated. It was found that the obtained results have shown that the ability of chitosan to coordinate heavy metal ions Zn(II), Cu(II), Cd(II), and Fe(III) is less or equal to the ability to retain ions of these metals in the pores of minerals without forming chemical bonds.

  11. Adsorption and removal at low atrazine concentration in an MBR pilot plant.

    PubMed

    Buttiglieri, G; Migliorisi, L; Malpei, F

    2011-01-01

    Atrazine is a persistent organic pollutant and it has been widely used in agriculture and forestry in the world for more than fifty years. Atrazine shows ecotoxicity effects in aquatic ecosystems even at very low level concentrations with endocrine disruptor activity. Few studies were carried out on atrazine removal performances in drinking and waste-water by biological treatments, especially in membrane bio-reactors (MBRs). MBR technology might be more efficient than the conventional one in the removal of micro-pollutants. The fate of atrazine in wastewater treatment plants and its influence on the biomass activity was evaluated in this study. The experimental work was divided in three different phases: inhibition studies on different types of biomass (by means of microcalorimetry); adsorption studies on different sludges (conventional activated sludge (CAS) - and MBR) calculating adsorption isotherms and, finally, atrazine removal in an MBR pilot plant (simulating a treatment of atrazine and nitrate contaminated groundwater). The absence of significant inhibition was observed; higher atrazine adsorption on MBR sludge was detected for lower atrazine concentration (<50 µg L(-1)); the removal efficiency in the MBR pilot plant was lower than 25% but higher than the theoretical one (based on adsorption isotherms).

  12. Adsorption properties of CFC and CFC replacements on activated carbon containing introduced ionic fluoride and chloride

    SciTech Connect

    Tanada, Seiki; Kawasaki, Naohito; Nakamura, Takeo; Abe, Ikuo

    1996-10-15

    Plasma technology has been available for the chlorofluorocarbon (CFC) decomposition or etching of silicone. The adsorption properties of CFC (CFC113) and CFC replacements (HCFC141b, HCFC225cb, and 5FP) on several kinds of plasma-treated activated carbons (P-ACs) prepared under different treatment gases were investigated using the adsorption isotherms, the limiting pore volume and the affinity coefficient and energy of adsorption calculated by the Dubinin-Radushkevich plot, and the quality and kinds of introduced fluoride and chloride. The dissolved fluoride and chloride atoms were introduced to the surface of activated carbon by CFC113, HCFC141b, and HCFC225cb, while the dissolved fluoride atoms were those from 5FP and tetrafluoromethane. The adsorbed amount of CFC and CFC replacements, except for 5FP, on P-ACs was larger than that on U-AC. The specific adsorption site on plasma-treated activated carbon of the CFC and CFC replacements was the fluoride atoms which were introduced by plasma treatment. It is concluded that the plasma-treated activated carbon was suitable for the recovery of CFC and CFC replacements, because the adsorbed amount of CFC and CFC replacements was larger than that on untreated activated carbon, and the adsorbed CFC and CFC replacements on activated carbon were decomposed by the plasma treatment.

  13. Design and cost estimate for the SRL integrated hot off gas facility using selective adsorption

    SciTech Connect

    Pence, D T; Kirstein, B E

    1981-07-01

    Based on the results of an engineering-scale demonstration program, a design and cost estimate were performed for a 25-m/sup 3//h (15-ft/sup 3//min) capacity pilot plant demonstration system using selective adsorption technology for installation at the Integrated Hot Off Gas Facility at the Savannah River Plant. The design includes provisions for the destruction of NO/sub x/ and the concentration and removal of radioisotopes of ruthenium, iodine-129, tritiated water vapor, carbon-14 contaminated carbon dioxide, and krypton-85. The nobel gases are separated by the use of selective adsorption on mordenite-type zeolites. The theory of noble gas adsorption on zeolites is essentially the same as that for the adsorption of noble gases on activated charcoals. Considerable detail is provided regarding the application of the theory to adsorbent bed designs and operation. The design is based on a comprehensive material balance and appropriate heat transfer calculations. Details are provided on techniques and procedures used for heating, cooling, and desorbing the adsorbent columns. Analyses are also given regarding component and arrangement selection and includes discussions on alternative arrangements. The estimated equipment costs for the described treatment system is about $1,400,000. The cost estimate includes a detailed equipment list of all the major component items in the design. Related technical issues and estimated system performance are also discussed.

  14. Experimental and Numerical Simulation of Water Vapor Adsorption and Diffusion in Shale Grains

    NASA Astrophysics Data System (ADS)

    Shen, W.; Tokunaga, T. K.; Cihan, A.; Wan, J.; Zheng, L.; Oldenburg, C. M.

    2015-12-01

    Advances in deep horizontal drilling and hydraulic fracturing have lead to large increases in production from unconventional shale gas reservoirs. Despite the success of this technology, uncertainties associated with basic transport processes require understanding in order to improve efficiency and minimize environmental impacts. The hydraulic fracturing process introduces large volumes of water into shale gas reservoirs. Most of the fracturing water remains in reservoirs to interfere with gas production. The quantification of the amount of water retained in shale gas reservoirs is crucial for predicting gas shale formation productivity and for optimizing extraction conditions. In this study, water vapor adsorption isotherms were gravimetrically measured on granular fractions of Woodford formation shales sieved after crushing. The isotherms were obtained at 30℃ and 50℃, for relative humidities from 11.1% to 97.0%. Water adsorption in these shale grains conformed to the typeⅡisotherm, and were nearly identical for the two experimental temperatures. In order to better understand the isotherms, a computational model based on the Maxwell-Stefan Diffusion equations (MSDM) was constructed to analyze the water adsorption and gas diffusion in shale grains. Based on the experimental results, the Guggenheim-Anderson-de Boer (GAB) isotherm model for gas adsorption was included in the model.

  15. Functionalized iron oxide/SBA-15 sorbent: investigation of adsorption performance towards glyphosate herbicide.

    PubMed

    Rivoira, Luca; Appendini, Marta; Fiorilli, Sonia; Onida, Barbara; Del Bubba, Massimo; Bruzzoniti, Maria Concetta

    2016-11-01

    Glyphosate is a worldwide-used herbicide occurring in many monitoring campaigns. Efficient technologies are currently unavailable for glyphosate removal from waters. In this work, a SBA-15 mesoporous silica-based material (Fe-NH2-SBA-15) was synthesized and studied for the adsorption of glyphosate from waters. In order to promote specific interactions between the sorbent and glyphosate via phosphoric group, iron oxide nanoparticles were encapsulated and a surface functionalization with (3-aminopropyl)triethoxysilane was accomplished. The adsorption of glyphosate on Fe-NH2-SBA-15 was investigated as a function of (i) pH, (ii) ionic strength (I), and (iii) adsorbate to adsorbent ratio (C), using a two-level, three-factor experimental design. The experimental design allowed for understanding the effect of the abovementioned variables and for proposing experimental conditions for quantitative removal (pH = 2.1, I = 1⋅10(-2) M and C = 0.35) under both batch and dynamic conditions. Interaction mechanism between glyphosate and Fe-NH2-SBA-15 sorbent was elucidated by studying the adsorption behavior of sorbents derived from the intermediate stages of synthesis and by desorption tests. Fe-NH2-SBA-15 sorbent can be quantitatively regenerated by 12.5 mM NaOH, and can be reused at least for five adsorption/desorption cycles. Quantitative removal of glyphosate from inlet and effluent wastewaters from a wastewater treatment plant is shown.

  16. Adsorption of basic dyes from aqueous solution onto pumice powder.

    PubMed

    Akbal, Feryal

    2005-06-15

    The adsorption of methylene blue and crystal violet on pumice powder samples of varying compositions was investigated using a batch adsorption technique. The effects of various experimental parameters, such as adsorbent dosage, initial dye concentration, and contact time, were also investigated. The extent of dye removal increased with decreased initial concentration of the dye and also increased with increased contact time and amount of adsorbent used. Adsorption data were modeled using the Freundlich adsorption isotherm. The adsorption kinetic of methylene blue and crystal violet could be described by the pseudo-second-order reaction model.

  17. [Adsorption dynamics and breakthrough characteristics based on the fluidization condition].

    PubMed

    Wang, Jun; Wang, Yao; Huang, Xing; Yuan, Yi-Long; Chen, Rui-Hui; Zhou, Hang; Zhou, Dan-Dan

    2014-02-01

    Few studies on the adsorption dynamics and breakthrough characteristics based on the fluidization condition have been reported. In a fluidized bed adsorption reactor with phenol as the adsorbate and granular activated carbon as the adsorbent, the adsorption efficiency, adsorption dynamic characteristics, adsorption breakthrough curves and adsorption capacities were studied and compared with those of a fixed bed operated under the same conditions. The results showed that the adsorption efficiencies exceeded 93% in 5 min in both the fluidized conditions and fixed conditions at the superficial velocities of 8 mm x s(-1) and 13 mm x s(-1). Meanwhile, the above adsorption reactions fitted to Pseudo-second-order with linear correlation coefficients greater than 0.999. The adsorption capacity of fluidized conditions was 8.77 mg x g(-1) and 24.70 mg x g(-1) at the superficial velocities of 6 mm x s(-1) and 8 mm x s(-1). Generally, the fluidized bed reactor showed a higher adsorption efficiency and greater adsorption capacity than the fixed bed reactor.

  18. Adsorption of selected volatile organic vapors on multiwall carbon nanotubes.

    PubMed

    Shih, Yang-hsin; Li, Mei-syue

    2008-06-15

    Carbon nanotubes are expected to play an important role in sensing, pollution treatment and separation techniques. This study examines the adsorption behaviors of volatile organic compounds (VOCs), n-hexane, benzene, trichloroethylene and acetone on two multiwall carbon nanotubes (MWCNTs), CNT1 and CNT2. Among these VOCs, acetone exhibits the highest adsorption capacity. The highest adsorption enthalpies and desorption energies of acetone were also observed. The strong chemical interactions between acetone and both MWCNTs may be the result from chemisorption on the topological defects. The adsorption heats of trichloroethylene, benzene, and n-hexane are indicative of physisorption on the surfaces of both MWCNTs. CNT2 presents a higher adsorption capacity than CNT1 due to the existence of an exterior amorphous carbon layer on CNT2. The amorphous carbon enhances the adsorption capacity of organic chemicals on carbon nanotubes. The morphological and structure order of carbon nanotubes are the primary affects on the adsorption process of organic chemicals.

  19. Adsorption of EDTA on activated carbon from aqueous solutions.

    PubMed

    Zhu, Hai-song; Yang, Xiao-juan; Mao, Yan-peng; Chen, Yu; Long, Xiang-li; Yuan, Wei-kang

    2011-01-30

    In this study, the adsorption of EDTA on activated carbon from aqueous solutions has been investigated in a batch stirred cell. Experiments have been carried out to investigate the effects of temperature, EDTA concentration, pH, activated carbon mass and particle size on EDTA adsorption. The experimental results manifest that the EDTA adsorption rate increases with its concentration in the aqueous solutions. EDTA adsorption also increases with temperature. The EDTA removal from the solution increases as activated carbon mass increases. The Langmuir and Freundlich equilibrium isotherm models are found to provide a good fitting of the adsorption data, with R(2) = 0.9920 and 0.9982, respectively. The kinetic study shows that EDTA adsorption on the activated carbon is in good compliance with the pseudo-second-order kinetic model. The thermodynamic parameters (E(a), ΔG(0), ΔH(0), ΔS(0)) obtained indicate the endothermic nature of EDTA adsorption on activated carbon.

  20. Adsorption of crude oil on anhydrous and hydrophobized vermiculite.

    PubMed

    da Silva, Umberto G; de F Melo, Marcus A; da Silva, Adaílton F; de Farias, Robson F

    2003-04-15

    This publication reports the adsorption of crude oil on vermiculite samples, expanded and hydrophobized with carnauba (Copernícia Cerífera) wax. The adsorption studies were performed by using columns filled with the vermiculite matrices and by dispersion of the vermiculite samples in an oil-water (50 ppm of oil) emulsion. The hydrate vermiculite exhibits a very low adsorption capacity against crude oil. On the other hand, anhydrous (expanded) and hydrophobized matrices show a high adsorption capacity. The 10% hydrophobized matrix show a 50% increased adsorption capacity, in comparison with the expanded one. For adsorption performed in the water-oil emulsion, saturation of the solid hydrophobized matrix is achieved after 60 min. The hydrophobized samples exhibit adsorption factors in the 0.7-1.0 range.

  1. Ibuprofen adsorption in four agricultural volcanic soils.

    PubMed

    Estevez, Esmeralda; Hernandez-Moreno, Jose Manuel; Fernandez-Vera, Juan Ramon; Palacios-Diaz, Maria Pino

    2014-01-15

    Ibuprofen (IB) is a high environmental risk drug and one of the most frequently prescribed in human medicine. Recently, IB has been detected in Gran Canaria in reclaimed water for irrigation and in groundwater. Adsorption was studied in four volcanic soils from three islands of the Canarian Archipelago. Once the biodegradation process has been excluded from the experimental conditions, a batch method was applied using initial concentrations of 1-5-10-20-50-100-200 mg L(-1) and two soil/water ratios (w/V): 1:5 (OECD, 2000) and 1:1. Non-linear and linearized Langmuir and Freundlich equations were well fitted. The wide IB range tested in our batch studies allowed us to measure experimental adsorption values close to the maximum adsorption capacity (S(max)) as estimated by Langmuir, making it possible thereby to validate the use of the Langmuir equation when there is a burst of contamination at high concentration. The distribution coefficient (Kd), S(max) and Retardation Factor (RF) varied from 0.04 to 0.5 kg L(-1), 4-200 mgk g(-1) and 1.2-1.9, respectively. The lowest S(max) and Kd values were found for the 1:1S/W ratio whereas most batch studies employ 1:5S/W ratios, thus obtaining higher adsorption parameters than when considering field conditions (1:1). Despite the high anion retention of andic soils, similar Kd and RF to those reported for other soils were obtained in 1:5, while high S(max) was found. Our results demonstrate that IB adsorption in volcanic areas responds not only to the soil properties commonly cited in adsorption studies, but also depends on andic properties, sorbent concentration and Dissolved Organic Carbon, the higher values of which are related to the lower Kd and S(max). The low RF and low detection frequency of the IB in groundwater suggests that a) reclaimed water irrigation is not the main source of IB, and b) the existence of some uncontrolled water disposal points in the zone.

  2. Evaluation of the adsorption capacity of alkali-treated waste materials for the adsorption of sulphamethoxazole.

    PubMed

    Kurup, Lisha

    2012-01-01

    The present work is to develop potential adsorbents from waste material and employ them for the removal of a hazardous antibacterial, sulphamethoxazole, from the wastewater by the Adsorption technique. The Adsorption technique was used to impound the dangerous antibiotics from wastewater using Deoiled Soya (DOS), an agricultural waste, and Water Hyacinth (WH), a prolific colonizer. The adsorption capacity of these adsorbents was further enhanced by treating them with sodium hydroxide solution and it was seen that the adsorption capacity increases by 10 to 25%. Hence a comparative account of the adsorption studies of all the four adsorbents, i.e. DOS, Alkali-treated DOS, WH and Alkali-treated Water Hyacinth has been discussed in this paper. Different isotherms like Freundlich, Langmuir and Dubinin-Radushkevich were also deduced from the adsorption data. Isotherm studies were in turn used in estimating the thermodynamic parameters. DOS showed sorption capacity of 0.0007 mol g(-1) while Alkali-treated Deoiled Soya exhibited 0.0011 mol g(-1) of sorption capacity, which reveals that the adsorption is higher in case of alkali-treated adsorbent. The mean sorption energy (E) was obtained between 9 and 12 kJ mol, which shows that the reaction proceeds by ion exchange reaction. Kinetic study reveals that the reaction follows pseudo-second-order rate equation. Moreover, mass transfer studies performed for the ongoing processes show that the mass transfer coefficient obtained for alkali-treated moieties was higher than the parent moieties. The breakthrough curves plotted from the column studies show percentage saturation of 90-98%. About 87-97% of sulphamethoxazole was recovered from column by desorption.

  3. [Characteristic of ammonia nitrogen adsorption on karst underground river sediments].

    PubMed

    Guo, Fang; Chen, Kun-Kun; Jiang, Guang-Hui

    2011-02-01

    Karst aquifers are one of the most important aquifers in Southwestern China. One of the characteristics of karst aquifers is the enhanced permeability permits high flow velocities are capable of transporting suspended and bedload sediments. Mobile sediment in karst may act as a vector for the transport of contaminates. 14 sediment samples were collected from two underground rivers in two typical karst areas in Liuzhou city, Guangxi Autonomous Region, China. According to simulated experiment methods, characteristic of adsorption of ammonia nitrogen on sediment was studied. The results of ammonia nitrogen adsorption dynamics on sediments showed that the maximum adsorption velocity was less than 2 h. The adsorption balance quantity in 5 h accounted for 71% - 98% of the maximum adsorption quantity. The maximum adsorption quantity of ammonia nitrogen was 385.5 mg/kg, which was sediment from a cave in the middle areas of Guancun underground river system. The study of isotherm adsorption indicated adsorption quantity of NH4+ increase followed by incremental balance concentration of NH4+ in the aquatic phase. Adsorption quantity of ammonia nitrogen in sediments has a relative linear relationship with adsorption balance concentrations. Adsorption-desorption balance concentrations were all low, indicating sediments from underground rivers have great adsorption potential. Under the condition of low and high concentrations of ammonia nitrogen in overlying water, Langmuir and Tempkin couldn't simulate or simulate results couldn't reach remarkable level, whilst Linear and Freundlich models could simulate well. Research on different type sediments, sampling times and depths from two underground rivers shows characteristic of ammonia nitrogen adsorption on karst underground river sediments doesn't have good correspondence with the type of sediments. One of the reasons is there is no big difference between sediments in the development of climate, geology, hydrological conditions

  4. Adsorption of Atmospheric Gases on Pu Surfaces

    SciTech Connect

    Nelson, A J; Holliday, K S; Stanford, J A; Grant, W K; Erler, R G; Allen, P G; McLean, W; Roussel, P

    2012-03-29

    Surface adsorption represents a competition between collision and scattering processes that depend on surface energy, surface structure and temperature. The surface reactivity of the actinides can add additional complexity due to radiological dissociation of the gas and electronic structure. Here we elucidate the chemical bonding of gas molecules adsorbed on Pu metal and oxide surfaces. Atmospheric gas reactions were studied at 190 and 300 K using x-ray photoelectron spectroscopy. Evolution of the Pu 4f and O 1s core-level states were studied as a function of gas dose rates to generate a set of Langmuir isotherms. Results show that the initial gas dose forms Pu{sub 2}O{sub 3} on the Pu metal surface followed by the formation of PuO{sub 2} resulting in a layered oxide structure. This work represents the first steps in determining the activation energy for adsorption of various atmospheric gases on Pu.

  5. Carbon adsorption system protects LPG storage sphere

    SciTech Connect

    Gothenquist, C.A.; Rooker, K.M.

    1996-07-01

    Chevron U.S.A. Products Co. installed a carbon adsorption system to protect an LPG storage sphere at its refinery in Richmond, Calif. Vessel damage can result when amine contamination leads to emulsion formation and consequent amine carry-over, thus promoting wet-H{sub 2}S cracking. In Chevron`s No. 5 H{sub 2}S recovery plant, a mixture of butane and propane containing H{sub 2}S is contacted with diethanolamine (DEA) in a liquid-liquid absorber. The absorber is a countercurrent contactor with three packed beds. Because the sweetening system did not include a carbon adsorption unit for amine purification, contaminants were building up in the DEA. The contaminants comprised: treatment chemicals, hydrocarbons, foam inhibitors, and amine degradation products. The paper describes the solution to this problem.

  6. Alkoxysilane adsorption on metal oxide substrates

    NASA Technical Reports Server (NTRS)

    Ramsier, R. D.; Zhuang, G. R.; Henriksen, P. N.

    1989-01-01

    Reflection-absorption infrared and inelastic electron tunneling spectroscopies have been used to study adsorption of liquid phase mono-, di-, and trialkoxysilanes on evaporated Al and Cu substrates. Spectral evidence shows that substrate properties influence the chemical and physical nature of trialkoxysilane films and that silane functionality plays a role in molecular orientation. Results show that dialkoxysilane films contain structural gradients, with adsorption at the monomolecular level influenced by surface morphology, and with organofunctionality and dosing procedure affecting the formation of thicker films. Evidence is presented that monoalkoxysilanes react with alumina surfaces, and a broad, multipeaked band from 1600 to 1900/cm has been interpreted as characteristic of the silylated AlO(x)Pb interface.

  7. Adsorption of cellulase on cellulose: effect of physicochemical properties of cellulose on adsorption and rate of hydrolysis

    SciTech Connect

    Lee, S.B.; Shin, H.S.; Ryu, D.D.Y.

    1982-11-01

    In the cellulase-cellulose reaction system, the adsorption of cellulase on the solid cellulose substrate was found to be one of the important parameters that govern the enzymatic hydrolysis rate of cellulose. The adsorption of cellulase usually parallels the rate of hydrolysis of cellulose. The affinity for cellulase varies depending on the structural properties of cellulose. Adsorption parameters such as the half-saturation constant, the maximum adsorption constant, and the distribution coefficient for both the cellulase and cellulose have been experimentally determined for several substrates. These adsorption parameters vary with the source of cellulose and the pretreatment methods and are correlated with the crystallinity and the specific surface area of cellulose substrates. The changing pattern of adsorption profile of cellulase during the hydrolysis reaction has also been elucidated. For practical utilization of cellulosic materials, the cellulose structural properties and their effects on cellulase adsorption, and the rate of hydrolysis must be taken into consideration. (Refs. 24).

  8. SEPARATION PROCESS USING COMPLEXING AND ADSORPTION

    DOEpatents

    Spedding, J.H.; Ayers, J.A.

    1958-06-01

    An adsorption process is described for separating plutonium from a solution of neutron-irradiated uranium containing ions of a compound of plutonium and other cations. The method consists of forming a chelate complex compound with plutoniunn ions in the solution by adding a derivative of 8- hydroxyquinoline, which derivative contains a sulfonic acid group, and adsorbing the remaining cations from the solution on a cation exchange resin, while the complexed plutonium remains in the solution.

  9. Thin layer joining by gas adsorption

    NASA Astrophysics Data System (ADS)

    Taga, Yasunori; Fukumura, Toshio

    2014-10-01

    Attempt has been made to join borosilicate glass and cycloolefin (COP) polymer film by using gas adsorption method. After corona plasma treat, COP was exposed to (3-glycidoxypropyl) trimethoxysilane (GPS) and glass to (3-aminopropyl) triethoxysilane (APS) both in air atmosphere, resulting in co-adsorption of water vapor in the atmosphere and organosilane gases. Surface characterization of plasma treated and gas adsorbed surfaces was carried out by X-ray photoelectron spectroscopy (XPS) using Mg Kα X-ray source. Joining was carried out by a roll laminator after contact of both surfaces at room temperature, followed by annealing at 130 °C for 10 min. Adhesion strength was evaluated by 180 degree peel test based on ASTM D-903 and durability was examined under the conditions of 60 °C and 95% RH. It was found that after plasma treatment, complex functional groups such as Csbnd H, Csbnd O, Cdbnd O, Osbnd Cdbnd O and CO3 were found on COP and Osbnd H on glass. Thickness of GPS gas adsorption layer on COP was evaluated by the XPS to be at least 1.1 nm by taking inelastic mean free path of Si2p photoelectron into consideration. Joining force was found to be more than 5 N/25 mm corresponding to almost equal to COP bulk tensile strength. In addition, durability of this adhesion strength remained unchanged over 2000 h even after exposure to the durability test conditions of 60 °C and 95% RH. The results can be explained in terms of formation of Hsbnd H hydrogen bonding and Sisbnd O covalent bonding via silanols will be made at the interface as a result of lamination and annealing processes. In conclusion, ultrathin joining method by gas adsorption was established by the formation of hydrogen and covalent bonds at the interface by low temperature reaction process.

  10. Water Adsorption Equilibria on Microporous Carbons

    DTIC Science & Technology

    1988-11-01

    of water adsorption on activated carbon is the presence of a large hysteresis loop indicating that the amount adsorbed depends on the past exposure...conditions of the carbon. The theories to describe hysteresis in microporous adsorbents and the experimental evidence to support each theory have been...observed behaviors on activated carbon. Neither the Dubinin- Serpinsky, nor the Sircar equations provide any explanation for hysteresis . It appears that

  11. Interlamellar adsorption of carbon dioxide by smectites

    USGS Publications Warehouse

    Fripiat, J.J.; Cruz, M.I.; Bohor, B.F.; Thomas, J.

    1974-01-01

    The adsorption of CO2 at low temperature (~ -70 ??C) on thin films of homoionic smectites was studied by X-ray diffraction and by i.r. absorption. An increase in the d001 spacings of these clay films upon adsorption of CO2 was observed. In addition, a dichroic effect was readily discernible by comparing the i.r. spectra at two different orientations of the smectite films; i.e. with the film normal and tilted 35 with respect to the i.r. beam. The CO2 stretching vibration at 2350 cm-1 was used for the i.r. study. These observations conclusively show that CO2 intercalates the smectite structure rather than being adsorbed only in pores between clay tactoids- the limiting process proposed by other investigators. Adsorption isotherm data from earlier surface area studies are re-examined here through application of the Dubinin equation. Again, intercalation is demonstrated by convergence of the plotted experimental data for smectites containing large monovalent interlayer cations toward a pore volume that is near the calculated theoretical value for a monolayer of intercalated CO2. Scanning electron photomicrographs of Li-and Cs- smectites provide additional evidence that aggregation differences are not responsible for the large observed difference in BET surface areas obtained for these smectites with CO2 as the adsorbate. At low magnification, visual differences in macro-aggregates are apparent, but at high magnification no significant differences are observed in the micro-structure of individual aggregates where the major amount of gas adsorption really occurs. ?? 1974.

  12. Adsorption edge study about cadmium, copper, nickel and zinc adsorption by variable charge soils

    NASA Astrophysics Data System (ADS)

    Casagrande, J. C.; Mouta, E. R.; Soares, M. R.

    2009-04-01

    The improper discharge of industrial and urban residues and the inadvertent use of fertilizers and pesticides can result in soil and water pollution and improve the potential of trace metals to enter in the human food chain. Adsorption reactions occur at the solid/liquid interface and are the most important mechanisms for controlling the activity of metal ions in soil solution. In a complex system with amphoteric behavior, the comprehension of the mobility, availability and fate of pollutants in the soil system is crucial for the prediction of the environmental consequences and for development of prevention/remediation strategies. A comparative study of cadmium (Cd), copper (Cu), nickel (Ni) and zinc (Zn) adsorption by highly weathered soils was carried out. Surface (0-0.2m) and subsoil (B horizon) samples were taken from a Rhodic Kandiudalf (RH), an Anionic "Xanthic" Acrudox (XA) and an Anionic "Rhodic" Acrudox (RA), located in brazilian humid tropical area. As the pH and the ionic strength are important environmental factors influencing the solution chemistry of heavy metals in variable charge systems, adsorption envelopes, in a batch adsorption experiment, were elaborated by reacting, for 24 h, soil samples with individual 0.01, 0.1 and 1.0 mol L-1 Ca(NO3)2 aqueous solutions containing nitrate salts of the adsorptive heavy metal (Cd, Cu, Ni and Zn) at the initial concentration of 5 mg L-1, with an increasing pH value from 3.0 to 8.0. pH50-100%, the difference between the pH of 100 and 50 percent metal adsorption was determined. A sharp increase of adsorption density (adsorption edge) was observed within a very narrow pH range, usually less than two pH units. Commonly, the relative affinity of a soil for a metal cation increases with the tendency of the cation to form inner-sphere surface complexes. This may be caused by differences in extent of hydrolysis of Cu ions and in affinity of adsorption sites for Cu. In general, subsurface samples showed low pH50

  13. Adsorption mechanism-based screening of cyclodextrin polymers for adsorption and separation of pesticides from water.

    PubMed

    Liu, Huihui; Cai, Xiyun; Wang, Yu; Chen, Jingwen

    2011-05-01

    A rational screening of cyclodextrin-based polymer (CDP), in terms of the relationship between adsorption potential and adsorbent-adsorbate, was investigated to adsorb and separate pesticides from water. Seven spherical porous CDPs were prepared with onefold or composite cyclodextrin(s) as complex and epichlorohydrin as cross-linking reagent. The adsorption kinetics and isotherms of the polymers toward a mixture of ten distinct pesticides clearly demonstrate that the adsorbents with a homogeneous open network structure can absorb pesticides via multiple adsorption interactions such as CD inclusion, loading into swelling water and physical adsorption on network. The multivariate regression analysis distinguishes the quantitative contributions of polymer properties to its adsorption potential, among which CD content, swelling capacity and pore size appear to be major influencing factors. Consequently, a facile mixture of three CDPs (i.e., β-CDP, RM-CDP and HP-CDP) was screened to obtain above prerequisite properties. The multiplex polymer could superiorly separate the pesticides at environmentally relevant levels from water.

  14. Adsorption energies and prefactor determination for CH3OH adsorption on graphite.

    PubMed

    Doronin, M; Bertin, M; Michaut, X; Philippe, L; Fillion, J-H

    2015-08-28

    In this paper, we have studied adsorption and thermal desorption of methanol CH3OH on graphite surface, with the specific aim to derive from experimental data quantitative parameters that govern the desorption, namely, adsorption energy Eads and prefactor ν of the Polanyi-Wigner law. In low coverage regime, these two values are interconnected and usually the experiments can be reproduced with any couple (Eads, ν), which makes intercomparison between studies difficult since the results depend on the extraction method. Here, we use a method for determining independently the average adsorption energy and a prefactor value that works over a large range of incident methanol coverage, from a limited set of desorption curves performed at different heating rates. In the low coverage regime the procedure is based on a first order kinetic law, and considers an adsorption energy distribution which is not expected to vary with the applied heating rate. In the case of CH3OH multilayers, Eads is determined as 430 meV with a prefactor of 5 × 10(14) s(-1). For CH3OH submonolayers on graphite, adsorption energy of 470 ± 30 meV and a prefactor of (8 ± 3) × 10(16) s(-1) have been found. These last values, which do not change between 0.09 ML and 1 ML initial coverage, suggest that the methanol molecules form island-like structure on the graphite even at low coverage.

  15. Adsorption of heavy metal ions using hierarchical CaCO3-maltose meso/macroporous hybrid materials: adsorption isotherms and kinetic studies.

    PubMed

    Ma, Xiaoming; Li, Liping; Yang, Lin; Su, Caiyun; Wang, Kui; Yuan, Shibao; Zhou, Jianguo

    2012-03-30

    Highly ordered hierarchical calcium carbonate is an important phase and has technological interest in the development of functional materials. The work describes hierarchical CaCO(3)-maltose meso/macroporous hybrid materials were synthesized using a simple gas-diffusion method. The uniform hexagonal-shaped CaCO(3)-maltose hybrid materials are formed by the hierarchical assembly of nanoparticles. The pore structure analysis indicates that the sample possesses the macroporous structure of mesoporous framework. The distinguishing features of the hierarchical CaCO(3)-maltose materials in water treatment involve not only high removal capacities, but also decontamination of trace metal ions. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The maximum removal capacity of the CaCO(3)-maltose hybrid materials for Pb(2+), Cd(2+), Cu(2+), Co(2+), Mn(2+) and Ni(2+) ions was 3242.48, 487.80, 628.93, 393.70, 558.66 and 769.23 mg/g, respectively. Adsorption data were modeled using the pseudo-first-order, pseudo-second-order and intra-particle diffusion kinetics equations. The results indicate that pseudo-second-order kinetic equation and intra-particle diffusion model can better describe the adsorption kinetics. The adsorption and precipitation transformation mechanism can be considered due to hierarchical meso/macroporous structure, rich organic ligands of the CaCO(3)-maltose hybrid materials and the larger solubility product of CaCO(3).

  16. Adsorption isotherm special study. Final report

    SciTech Connect

    1993-05-01

    The study was designed to identify methods to determine adsorption applicable to Uranium Mill Tailings Remedial Action (UMTRA) Project sites, and to determine how changes in aquifer conditions affect metal adsorption, resulting retardation factors, and estimated contaminant migration rates. EPA and ASTM procedures were used to estimate sediment sorption of U, As, and Mo under varying groundwater geochemical conditions. Aquifer matrix materials from three distinct locations at the DOE UMTRA Project site in Rifle, CO, were used as the adsorbents under different pH conditions; these conditions stimulated geochemical environments under the tailings, near the tailings, and downgradient from the tailings. Grain size, total surface area, bulk and clay mineralogy, and petrography of the sediments were characterized. U and Mo yielded linear isotherms, while As had nonlinear ones. U and Mo were adsorbed strongly on sediments acidified to levels similar to tailings leachate. Changes in pH had much less effect on As adsorption. Mo was adsorbed very little at pH 7-7.3, U was weakly sorbed, and As was moderately sorbed. Velocities were estimated for metal transport at different pHs. Results show that the aquifer materials must be characterized to estimate metal transport velocities in aquifers and to develop groundwater restoration strategies for the UMTRA project.

  17. Nitrogen Adsorption on Graphite: Defying Physisorption

    NASA Astrophysics Data System (ADS)

    Tkatchenko, Alexandre; Scheffler, Matthias

    2010-03-01

    The adsorption of a nitrogen molecule at the graphite surface can be considered a paradigm of molecular physisorption [1]. The binding of N2 can be phenomenologically described in terms of a competition between quadrupole--quadrupole and van der Waals dispersion energies. Of particular interest is the relative stability of the so-called ``in-plane'', ``out-of-plane'' and ``pin-wheel'' monolayer structures, in which the nitrogen molecules alternate between parallel and perpendicular configurations on the surface. By combining state-of-the-art electronic structure methods, such as dispersion-corrected density-functional theory and Møller-Plesset second-order perturbation theory along with high-level coupled cluster [CCSD(T)] calculations, we are able to gain quantitative insight into the adsorption mechanism of N2@graphite and achieve very good agreement with experimental desorption enthalpy. We challenge the commonly held view of a closed-shell adsorbed N2 molecule, finding a noticeable charge-density polarization for nitrogen in a perpendicular configuration on the surface. We map out the N2@graphite potential energy surface as a function of sliding and orientation and discuss the influence of quantum zero-point energy for different adsorption sites. [1] D. Marx and H. Wiechert, Adv. Chem. Phys. 95, 213 (1996).

  18. Aqueous mercury adsorption by activated carbons.

    PubMed

    Hadi, Pejman; To, Ming-Ho; Hui, Chi-Wai; Lin, Carol Sze Ki; McKay, Gordon

    2015-04-15

    Due to serious public health threats resulting from mercury pollution and its rapid distribution in our food chain through the contamination of water bodies, stringent regulations have been enacted on mercury-laden wastewater discharge. Activated carbons have been widely used in the removal of mercuric ions from aqueous effluents. The surface and textural characteristics of activated carbons are the two decisive factors in their efficiency in mercury removal from wastewater. Herein, the structural properties and binding affinity of mercuric ions from effluents have been presented. Also, specific attention has been directed to the effect of sulfur-containing functional moieties on enhancing the mercury adsorption. It has been demonstrated that surface area, pore size, pore size distribution and surface functional groups should collectively be taken into consideration in designing the optimal mercury removal process. Moreover, the mercury adsorption mechanism has been addressed using equilibrium adsorption isotherm, thermodynamic and kinetic studies. Further recommendations have been proposed with the aim of increasing the mercury removal efficiency using carbon activation processes with lower energy input, while achieving similar or even higher efficiencies.

  19. Modelling the arsenic (V) and (III) adsorption

    NASA Astrophysics Data System (ADS)

    Rau, I.; Meghea, A.; Peleanu, I.; Gonzalo, A.; Valiente, M.; Zaharescu, M.

    2003-01-01

    Arsenic has gained great notoriety historically for its toxic properties. In aquatic environment, arsenic can exist in several oxidation states, as both inorganic and organometallic species. As (V) is less toxic than As (III). Most research has been directed to the control of arsenic pollution of potable water. Various techniques such as precipitation with iron and aluminium hydroxides, ion exchange, reverse osmosis, and adsorption are used for As (V) removal from surface and waste waters. Because of the easy handling of sludge, its free operation and regeneration capability, the adsorption technique has secured a place as one of the advanced methods of arsenic removal. A study of As (III) and As (V) sorption onto some different adsorbents (Fe (III) — iminodiacetate resin, nanocomposite materials, Fe(III) — forager sponge) referring to kinetic considerations and modelling of the process will be presented. All the systems studied are better described by Freundlich-Langmuir isotherm and the rate constant evaluation shows a sub-unitary order for the adsorption process.

  20. Multisite adsorption of cadmium on goethite

    SciTech Connect

    Venema, P.; Hiemstra, T.; Riemsdijk, W.H. van

    1996-11-10

    Recently a new general ion adsorption model has been developed for ion binding to mineral surfaces (Hiemstra and van Riemsdijk, 1996). The model uses the Pauling concept of charge distribution (CD) and is an extension of the multi-site complexation (MUSIC) approach. In the CD-MUSIC model the charge of an adsorbing ion that forms an inner sphere complex is distributed over its ligands, which are present in two different electrostatic planes. In this paper the authors have applied the CD-MUSIC model to the adsorption of metal cations, using an extended data set for cadmium adsorbing on goethite. The adsorption of cadmium and the cadmium-proton exchange ratio were measured as function of metal ion concentration, pH, and ionic strength. The data could be described well, taking into account the surface heterogeneity resulting from the presence of two different crystal planes (the dominant 110 face and the minor 021 face). The surface species used in the model are consistent with recent EXAFS data. In accordance with the EXAFS results, high-affinity complexes at the 021 face were used in the model.

  1. Adsorptive separation of propylene-propane mixtures

    SciTech Connect

    Jaervelin, H.; Fair, J.R. )

    1993-10-01

    The separation of propylene-propane mixtures is of great commercial importance and is carried out by fractional distillation. It is claimed to be the most energy-intensive distillation practiced in the United States. The purpose of this paper is to describe experimental work that suggests a practical alternative to distillation for separating the C[sub 3] hydrocarbons: adsorption. As studied, the process involves three adsorptive steps: initial separation with molecular sieves with heavy dilution with an inert gas; separation of propylene and propane separately from the inert gas, using activated carbon; and drying of the product streams with any of several available desiccants. The research information presented here deals with the initial step and includes both equilibrium and kinetic data. Isotherms are provided for propylene and propane adsorbed on three zeolites, activated alumina, silica gel, and coconut-based activated carbon. Breakthrough data are provided for both adsorption and regeneration steps for the zeolites, which were found to be superior to the other adsorbents for breakthrough separations. A flow diagram for the complete proposed process is included.

  2. Adsorption of Nanoplastics on Algal Photosynthesis

    NASA Astrophysics Data System (ADS)

    Turner, James; Bhattacharya, Priyanka; Lin, Sijie; Ke, Pu Chun

    2010-03-01

    The rapid accumulation of disposed plastics in the environment, especially in the Pacific Ocean, has become a global concern in recent years. Photo, chemical and physical degradations constantly fragment these plastics into a wide array of macroscopic to microscopic particles. As a result, marine organisms such as algae may be exposed to plastic particles through ingestion, adsorption and other forms of uptake. Such interactions, currently little understood, could potentially impact on the health state of the entire food chain. Here we report on polystyrene-algae interaction and its impact on algal photosynthesis. We first investigated the adsorption of polystyrene beads (20 nm) on a cellulose film coated on a 96-well plate. We derived a supralinear increase of the adsorption with the beads concentration for both positively and negatively charged polystyrene beads, with a saturation observed for the negatively charged polystyrene beads of concentration above 1.6 mg/mL. Using a bicarbonate indicator we discovered decreased carbon dioxide depletion due to polystyrene-algae binding. Since polystyrene beads also mediated algae aggregation, nanoplastics may alternatively be harnessed for waste water treatment.

  3. Adsorption of oxygen onto zeolites at pressures up to 15 MPa

    NASA Astrophysics Data System (ADS)

    Helvensteijn, Bernardus P.; Wang, Yu; Levan, Douglas; Luna, Bernadette; Kashani, Ali

    2012-06-01

    For NASA applications, high-pressure oxygen is an integral part of portable life support systems (PLSSs) for Extravehicular Activities (EVAs), some fuel cell systems and potential In Situ Resource Utilization (ISRU) systems. New high-pressure oxygen generation systems will be needed on the International Space Station (to enable EVAs after the Shuttle is retired), on a Lunar Lander (to use lower pressure cryogenic tanks as a source of high pressure oxygen for EVAs) and on a planetary habitat (to generate and store high pressure oxygen for extended periods of time). One of the candidate technologies for producing high-pressure oxygen, temperature swing adsorption (TSA) compression, offers many advantages but has a low technology readiness level. Evaluation of technical feasibility and safety issues, and specification of operating parameters of the compressor require the availability of fundamental equilibrium adsorption data. A cryogenic, highpressure volumetric equilibrium adsorption apparatus has been developed at NASA Ames Research Center to facilitate collection of the needed data. The apparatus incorporates cryogenic and vacuum surrounds, and a high-pressure oxygen circuit. In this paper, lowtemperature equilibrium isotherms of oxygen on various sorbent materials are presented. The data presented will aid the development of a space qualified TSA system

  4. Studies on adsorption-desorption of xenon on surface of BC-404 plastic scintillator based on soaking method

    NASA Astrophysics Data System (ADS)

    Yongchun, Xiang; Tieshuan, Fan; Chuanfei, Zhang; Fei, Luo; Qian, Wang; Rende, Ze; Qingpei, Xiang

    2017-03-01

    The phoswich coincidence detector is used to verify the CTBT treaty by measuring radioxenon and as such needs to possess high detection sensitivity. However, residual xenon adsorbed onto the surface of β detectors greatly influences subsequent measurements of weak samples. In this study, we investigate the adsorption-desorption behavior of xenon on BC-404 scintillator surfaces with different coating thicknesses using the soaking method. The results present the desorption behavior of xenon on a BC-404 surface for the first time. The calculated adsorption capacity for an uncoated surface is consistent with that from previous studies. However, due to factors such as limitations in coating technology, the effectiveness of coating on reducing the "memory effect" of the detector was poor. The proposed method is suitable for studying the adsorption-desorption behavior of gases on solid surfaces due to its simplicity and flexibility.

  5. TiO2 crystal facet-dependent antimony adsorption and photocatalytic oxidation.

    PubMed

    Song, Jiaying; Yan, Li; Duan, Jinming; Jing, Chuanyong

    2017-02-24

    Anatase TiO2 crystal facets are garnering increasing attention due to their unique surface property. However, no specific linear relationship had been derived between the facet exposed on TiO2 and the surface adsorption capacity as well as photocatalytic performance. This study systematically explored the facet effects on antimony (Sb) adsorption and photocatalytic oxidation using high-index {201} and low-index {101}, {001}, and {100} TiO2. The results suggest that high-index {201} TiO2 exhibits the best Sb(III) adsorption and photocatalytic activity compared to the low-index TiO2. Both the Sb(III) adsorption density and the amount of OH and O2(-) generated in solution were correlated to the magnitude of surface energy on TiO2 facets. Photocatalytically generated OH and O2(-) were responsible for Sb(III) photooxidation as evidenced by radical-trapping experiments. The great contribution of OH was observed only on {201}, not on low-index TiO2. This phenomenon was found to be attributable to the high surface energy on {201}, which enables the generation of a large amount of photogeneration OH to compensate for the fast rate of OH dissipation. Therefore, the predominant participation of OH in Sb(III) photooxidation was only possible on high-index {201} TiO2, which resulted in an enhanced photocatalytic rate. On the other hand, O2(-) dominated the Sb(III) photocatalytic oxidation on low-index TiO2. The intrinsic facet-dependent adsorption and photocatalytic mechanism obtained from this study would be useful for developing TiO2-based environmental technologies.

  6. CO2 adsorption-assisted CH4 desorption on carbon models of coal surface: A DFT study

    NASA Astrophysics Data System (ADS)

    Xu, He; Chu, Wei; Huang, Xia; Sun, Wenjing; Jiang, Chengfa; Liu, Zhongqing

    2016-07-01

    Injection of CO2 into coal is known to improve the yields of coal-bed methane gas. However, the technology of CO2 injection-enhanced coal-bed methane (CO2-ECBM) recovery is still in its infancy with an unclear mechanism. Density functional theory (DFT) calculations were performed to elucidate the mechanism of CO2 adsorption-assisted CH4 desorption (AAD). To simulate coal surfaces, different six-ring aromatic clusters (2 × 2, 3 × 3, 4 × 4, 5 × 5, 6 × 6, and 7 × 7) were used as simplified graphene (Gr) carbon models. The adsorption and desorption of CH4 and/or CO2 on these carbon models were assessed. The results showed that a six-ring aromatic cluster model (4 × 4) can simulate the coal surface with limited approximation. The adsorption of CO2 onto these carbon models was more stable than that in the case of CH4. Further, the adsorption energies of single CH4 and CO2 in the more stable site were -15.58 and -18.16 kJ/mol, respectively. When two molecules (CO2 and CH4) interact with the surface, CO2 compels CH4 to adsorb onto the less stable site, with a resulting significant decrease in the adsorption energy of CH4 onto the surface of the carbon model with pre-adsorbed CO2. The Mulliken charges and electrostatic potentials of CH4 and CO2 adsorbed onto the surface of the carbon model were compared to determine their respective adsorption activities and changes. At the molecular level, our results showed that the adsorption of the injected CO2 promoted the desorption of CH4, the underlying mechanism of CO2-ECBM.

  7. Adsorption of ammonium on biochar prepared from giant reed.

    PubMed

    Hou, Jie; Huang, Lei; Yang, Zhimin; Zhao, Yaqi; Deng, Chaoren; Chen, Yucheng; Li, Xin

    2016-10-01

    Giant reed was used as precursor for making biochar in order for the adsorption of NH4 (+)-N from aqueous solution. And the adsorption of the product to NH4 (+)-N was examined. The surface features of biochar were investigated by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy/energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD). XRD patterns showed several peaks and correspond to the high amount of crystalline material. The crystals contain KCl, K2O, CaO, MgO, and SiO and possess high surface area which enhances adsorption. The influence of different parameters such as initial concentration, adsorption time, pH, and ionic strength has been carried out. The adsorption could reach equilibrium through 24 h reaction and had the best adsorption amount at the solution pH values from 7 to 9. The cation has great influence on the adsorption of NH4 (+)-N, whereas the anion exerted a weaker effect. The adsorption followed pseudo-first-order and pseudo-second-order models. And the intraparticle diffusion and desorption studies further elucidated that the mechanism of adsorption on the product was ion exchange. The product equilibrium data was well described by the Langmuir and Freundlich model. The maximum adsorption capacities were 1.490 mg/g. Biochar derived from giant reed at 500 °C was suggested as a promising adsorbent for the removal of NH4 (+)-N from slightly polluted wastewater.

  8. Adsorption Behavior of Pb(II) Onto Potassium Polytitanate Nanofibres.

    PubMed

    Shahid, Mohammad; Tiling, Leonard D; El Saliby, Ibrahim; McDonagh, Andrew; Kim, Jong-Beom; Kim, Jong-Ho; Shon, Ho Kyong

    2016-02-01

    Potassium polytitanate nanofibres prepared by a hydrothermal method were investigated for their possible application in removing toxic metals from aqueous solution. Particular attention was paid to employing the titanate as a novel effective adsorbent for the removal of Pb(II). Batch adsorption experiments demonstrated that the adsorption was influenced by various conditions such as solution pH, adsorbent dosage and initial Pb(II) concentration. The results showed that the adsorption rate was faster in the first 5 min and equilibrium was achieved after 180 min. The maximum amount of adsorption was detected at pH 5. Potassium titanate showed much higher adsorption capacity compared to P25. The kinetic studies indicated that the adsorption of Pb(II) onto titanate best fit the pseudo-second-order kinetic model. FTIR spectra revealed that the hydroxyl groups in titanate were responsible for Pb(II) adsorption. The principal mechanism of the adsorption of Pb(II) in the present study is attributed to both ion exchange and oxygen bonding. The adsorption-desorption results demonstrated that the titanate could be readily regenerated after adsorption. Therefore, the present titanate exhibits great potential for the removal of Pb(II) from wastewater.

  9. Adsorption mechanism of chloroacetanilide herbicides to modified montmorillonite.

    PubMed

    El-Nahhal, Yasser

    2003-09-01

    This study was undertaken to characterize the adsorption mechanism of alachlor and metolachlor on montmorillonite modified with cationic surfactants. Adsorbed amounts of cationic surfactant on montmorillonite surfaces were determined by CNHSO analyzer. Equilibrium concentrations of alachlor and metolachlor were determined by GC and adsorption results were fit to a linear regression equation. The slope of the isotherms (Kd) was normalized to the fraction of organic carbon on montmorillonite complexes to produce corresponding Koc. Adsorption of surfactants fit very well to Langmuir equation. Increased basal spacing indicates that surfactant molecules could penetrate through the interlayer spacing and arrange themselves in different ways. Equilibrium data of alachlor and metolachlor suggest that adsorption may occur via physical or chemical bonds. Koc values of alachlor or metolachlor decreased as the fraction of the organic carbon increased in montmorillonite complexes indicating independent adsorption process. Changes of the molar free energy of the adsorption reactions were in the range of physical adsorption, indicating that adsorption reactions are spontaneous and the molecules either adsorb on the surface or penetrate into the inter-layers of montmorillonite-surfactant complex. Careful investigation of the adsorption data suggests that interaction may occur via the active groups such as carbonyl group (-C=O), anilidic (C-N) group and/or phenyl rings. This information may provide better understanding on adsorption mechanism and be useful in designing ecologically acceptable herbicide formulations.

  10. Effect of pore blockage on adsorption isotherms and dynamics: Anomalous adsorption of iodine on activated carbon

    SciTech Connect

    Bhatia, S.K.; Liu, F.; Arvind, G.

    2000-04-18

    Isotherm hysteresis and pore-clocking effects of trapped molecules on adsorption dynamics is studied here, using the iodine-carbon system in the 300--343 K temperature range. It is found that a portion of the iodine is strongly adsorbed, and does not desorb, even over very long time scales, while the remainder adsorbs reversibly as a homogeneous monolayer with a Langmuirian isotherm in mesopores. The strongly adsorbed iodine appears to adsorb in micropores and at the mesopore mouths, hindering uptake of the reversible iodine. The uptake data for the adsorption and desorption dynamics of the reversible part is found to be best explained by means of a pore mouth resistance control mechanism. it is concluded that the dynamics of the adsorption and desorption at the pore mouth is important at early stages of the process.

  11. High Efficiency Adsorption Chillers: High Efficiency Adsorption Cooling Using Metal Organic Heat Carriers

    SciTech Connect

    2010-10-01

    BEETIT Project: PNNL is incorporating significant improvements in materials that adsorb liquids or gases to design more efficient adsorption chillers. An adsorption chiller is a type of air conditioner that is powered by heat, solar or waste heat, or combustion of natural gas. Unlike typical chillers, this type has few moving parts and uses almost no electricity to operate. PNNL is designing adsorbent materials at the molecular level with at least 3 times higher refrigerant capacity and up to 20 times faster kinetics than adsorbents used in current chillers. By using the new adsorbent, PNNL is able to create a chiller that is significantly smaller, has twice the energy efficiency, and lower costs for materials and assembly time compared to conventional adsorption chillers.

  12. Effect of cropping systems on adsorption of metals by soils: I. Single-metal adsorption

    SciTech Connect

    Basta, N.T.; Tabatabai, M.A. )

    1992-02-01

    The effect of long-term cropping systems on adsorption of metals was studied for soils obtained from two sites, Clarion-Webster Research Center (CWRC site) at Kanawha and Galva-Primghar Research Center (GPRC site) at Sutherland, under long-term rotation experiments in Iowa. Each experiment consisted of three cropping systems: continuous corn (CCCC), corn-soybean-corn-soybean (CSCS), and corn-oats-meadow-meadow (COMM), and treated with (+N) and without (0 N) ammoniacal fertilizer. In general, CSCS and COMM cropping systems did not significantly affect the metal adsorption maxima of soils obtained from both sites. Cadmium, Cu, and Pb adsorption were significantly correlated with pH and percentage base saturation for soils from both sites.

  13. Phosphate mediated adsorption and electron transfer of cytochrome c. A time-resolved SERR spectroelectrochemical study.

    PubMed

    Capdevila, Daiana A; Marmisollé, Waldemar A; Williams, Federico J; Murgida, Daniel H

    2013-04-21

    The study of proteins immobilized on biomimetic or biocompatible electrodes represents an active field of research as it pursues both fundamental and technological interests. In this context, adsorption and redox properties of cytochrome c (Cyt) on different electrode surfaces have been extensively reported, although in some cases with contradictory results. Here we report a SERR spectroelectrochemical study of the adsorption and electron transfer behaviour of the basic protein Cyt on electrodes coated with amino-terminated monolayers. The obtained results show that inorganic phosphate (Pi) and ATP anions are able to mediate high affinity binding of the protein with preservation of the native structure and rendering an average orientation that guarantees efficient pathways for direct electron transfer. These findings aid the design of Cyt-based bioelectronic devices and understanding the modulation by Pi and ATP of physiological functions of Cyt.

  14. Siloxane treatment by adsorption into porous materials.

    PubMed

    Ricaurte Ortega, D; Subrenat, A

    2009-09-01

    Siloxanes are widely used in different applications: health care, dry cleaning, household products, paints and coatings, paper, personal care, for example. This explains their prevalence in the environment. Because of their volatile nature, most of the time they are dispersed in the atmosphere, but they can also be present in the slurry from landfills. During anaerobic digestion, when the temperature goes up to 60 degrees C, siloxanes are volatilized, forming part of the biogas. Operational problems using biogas to produce energy, heat and hydrogen have been identified. At high temperatures the siloxanes are transformed into silicate dioxide (commonly called sand transmission). These white deposits may adhere to metal or catalytic substrate surfaces, seriously reducing equipment efficiency, and this can be a reason for changing equipment warranties. Consequently, elimination of siloxanes has become very important. Unfortunately, relatively little information can be found on this subject. Nevertheless some authors have described different analytical methods for siloxane quantification, and recent studies have looked at the presence of siloxanes in landfills and the restriction on the energy recovery equipment using the biogas produced. The growing consumption of siloxanes and silicones in industrial processes consequently increase their prevalence in the environment, hampering the use of biogas as a source of 'green energy'. Therefore, the principal focus of this study is the treatment of siloxanes. Their elimination was carried out using an adsorption process with four different porous materials: activated carbon cloths (ACC), granular activated carbon (GAC), zeolite and silica gel. Two representative siloxane compounds were used in this study, hexamethyldisiloxane (L2) and octamethylcyclotetrasiloxane (D4). Adsorption kinetics and isotherms in batch reactors were performed. It was observed that the mass transfer into the porous material was more rapid for the

  15. Technology Development.

    ERIC Educational Resources Information Center

    Gomory, Ralph E.

    1983-01-01

    The evolutionary character and complexity of technological development is discussed, focusing on the steam engine and computer as examples. Additional topics include characteristics of science/technology, cultural factors in technological development, technology transfer, and problems in technological organization. (JN)

  16. Treatment technologies and mechanisms for three odorants at trace level: IPMP, IBMP, and TCA.

    PubMed

    Li, Xin; Lin, Pengfei; Wang, Jun; Liu, Yuanyuan; Li, Yong; Zhang, Xiaojian; Chen, Chao

    2016-01-01

    Odour episodes caused by algal metabolites are gaining more and more attention in recent years. Besides geosmin and 2-methylisoborneol (MIB), 2-isopropyl-3-methoxypyrazine (IPMP), 2-isobutyl-3-methoxypyrazine (IBMP), and 2,4,6-trichloroanisole (TCA) have emerged to be important off-flavour sources. Their low odour threshold concentrations (several ng ·L(-1)), which are even lower than those of MIB and geosmin, pose challenges for treatment strategies. Hence, a practical and efficient mitigation technology is needed. The possible practical technologies, including powdered activated carbon (PAC) adsorption and oxidation by chlorine and potassium permanganate, were investigated. The results indicated that chlorine and potassium permanganate oxidation of the three odorants were unfeasible while PAC adsorption was effective. As for adsorption, TCA, followed by IBMP and IPMP, was most easily removed by PAC. The Freundlich model could well describe the adsorption isotherm data. The adsorption capacities for IPMP, IBMP, and TCA were described as follows: [Formula: see text], [Formula: see text], and [Formula: see text]. For five earthy/musty odorants including geosmin and MIB, octanol/water partition coefficient, molecular weight, and polarizability all promoted adsorption while aqueous solubility showed a negative influence. The hydrophobic interaction was believed to be the dominant force in the adsorption mechanism while the π-electron interaction enhanced adsorption when a benzene ring was present. This result could be used to predict the adsorption performance of emerging odorants.

  17. Thiol adsorption at gold surfaces: self-assembly, chiral recognition, and enantioselective adsorption at chiral surfaces.

    NASA Astrophysics Data System (ADS)

    Hammer, Bjork

    2003-03-01

    Density functional theory calculations are presented for the adsorption of thiol containing molecules on to Au(111), Au(110), and Au(17 11 9). The thiol group becomes dehydrogenated during the adsorption process and the resulting thiolate group shows a strong preference for the Au-Au bridging adsorption site.[1] For methylthiolate adsorption, a restructuring of the Au(111) surface in to a honeycomb pattern with every 3rd Au atom missing is found to lead an overall strengthening of the thiolate-gold bonding.[2] Since the surface restructuring must happen through-out the system, it represents a net attractive interaction between the adsorbates and it is speculated to have implications for the self-assembly of alkanethiols found at close packed gold surfaces. Adsorption studies of the naturally occuring amino acid, cysteine, at Au(110) also reveal enhanced thiolate-gold bonding at restructured Au sites.[3] The cysteine molecules are found to interact pairwise forming dimers that are hydrogen bonded through the cysteine carboxyl groups. The gold surface restructuring required to hold this complex involves the creation of a four Au atom wide vacancy in the outermost close packed row of the Au(110) surface. The binding of the the cysteine dimer to this vacancy site causes chiral recognition -- only cysteine dimers formed between like cysteine enantiomers are able to bind to the surface. For cysteine adsorption over the chiral (kinked) Au(17 11 9) surface no enantiospecific adsorption is found since the molecule only binds through the thiolate and amino groups.[4] Modifying the adsorbate by substituting the noninteracting carboxyl group with a dimethylphosphino group provides a third strong adsorbate-surface bond thereby enabling the discrimination during adsorption of two molecular enantiomers by one particular chiral Au surface. [1] J. Gottschalck and B. Hammer, J. Chem. Phys. 116, 784 (2002). [2] L.M. Molina and B. Hammer, Chem. Phys. Lett. 360, 264 (2002). [3] A

  18. Adsorption studies of methylene blue dye on tunisian activated lignin

    NASA Astrophysics Data System (ADS)

    Kriaa, A.; Hamdi, N.; Srasra, E.

    2011-02-01

    Activated carbon prepared from natural lignin, providing from a geological deposit, was used as the adsorbent for the removal of methylene blue (MB) dye from aqueous solutions. Batch adsorption studies were conducted to evaluate various experimental parameters like pH and contact time for the removal of this dye. Effective pH for MB removal was 11. Kinetic study showed that the adsorption of dye was gradual process. Quasi equilibrium reached in 4 h. Pseudo-first-order, pseudo-second-order were used to fit the experimental data. Pseudo-second-order rate equation was able to provide realistic description of adsorption kinetics. The experimental isotherms data were also modelled by the Langmuir and Freundlich equation of adsorption. Equilibrium data fitted well with the Langmuir model with maximum monolayer adsorption capacity of 147 mg/g. Activated lignin was shown to be a promising material for adsorption of MB from aqueous solutions.

  19. Communication: Thermodynamic analysis of critical conditions of polymer adsorption

    NASA Astrophysics Data System (ADS)

    Cimino, R.; Rasmussen, C. J.; Neimark, A. V.

    2013-11-01

    Polymer adsorption to solid surfaces is a ubiquitous phenomenon, which has attracted long-lasting attention. Dependent on the competition between the polymer-solid adsorption and polymer-solvent solvation interactions, a chain may assume either 3d solvated conformation when adsorption is weak or 2d adsorbed conformation when adsorption is strong. The transition between these conformations occurring upon variation of adsorption strength is quite sharp, and in the limit of "infinite" chain length, can be treated as a critical phenomenon. We suggest a novel thermodynamic definition of the critical conditions of polymer adsorption from the equality of incremental chemical potentials of adsorbed and free chains. We show with the example of freely jointed Lennard-Jones chains tethered to an adsorbing surface that this new definition provides a link between thermodynamic and geometrical features of adsorbed chains and is in line with classical scaling relationships for the fraction of adsorbed monomers, chain radii of gyration, and free energy.

  20. Adsorption of carbon black using carboxymethyl chitosan in deinking process

    NASA Astrophysics Data System (ADS)

    Muryeti, Budimulyani, Estuti; Sinurat, Ellya

    2017-03-01

    The study about synthesis, characterization, and application carboxymethyl chitosan as adsorbent in deinking process was conducted. Adsorption of carbon black onto carboxymethyl chitosan has been investigated in a batch system. This research was conducted to obtain the adsorption capacity of carboxymethyl chitosan. The experiments were carried out to study the effect of carbon black concentration, contact time and dosage of carboxymethyl chitosan to the adsorption capacity of carboxymethyl chitosan. The optimum condition of carbon black adsorption was achieved at contact time of 60 min and weight doses of 1.0 g. The adsorption capacity of carboxymethyl chitosan was 14.34 mg/g and the adsorption effectivity was 70.54%. The result indicates that carboxymethyl chitosan could be used as adsorbent of carbon black in deinking process.

  1. Computational Investigation of Conformational Changes in Proteins upon Adsorption

    NASA Astrophysics Data System (ADS)

    Sharma, Sumit; Anand, Gaurav; Belfort, Georges; Kumar, Sanat K.

    2009-03-01

    Amyloidogenic diseases, such as, Alzheimer's, are caused by adsorption and aggregation of partially unfolded proteins. Protein adsorption is often accompanied by conformational rearrangements, which are thought to affect many properties such as their adhesion strength to the surface, biological activity, and aggregation tendency. Experiments have shown that many proteins, upon adsorption to hydrophobic surfaces, undergo a helix to sheet or random coil secondary structural rearrangement. To better understand the equilibrium structural complexities of this phenomenon, we have performed Monte Carlo (MC) simulations and Single Chain Mean Field calculations of adsorption of different proteins, modeled as lattice chains, to study the adsorption behavior and equilibrium protein conformations at different temperatures, protein concentration and surface hydrophobicity. Free energy and entropic effects on adsorption have been studied by determining density of states using Weighted Histogram Analysis Method. Conformational transitions of proteins on surfaces will be discussed as a function of surface hydrophobicity.

  2. Factors affecting the adsorption of chromium (VI) on activated carbon

    SciTech Connect

    Yavuz, R.; Orbak, I.; Karatepe, N.

    2006-09-15

    The aim of this investigation was to determine the adsorption behavior of chromium (VI) on two different activated carbon samples produced from Tuncbilek lignite. The effects of the initial chromium (VI) concentration (250-1000 mg/L), temperature (297-323 K) and pH (2.0-9.5) on adsorption were investigated systematically. The effectiveness of the parameters on chromium adsorption was found to be in the order of pH, the initial Cr(VI) concentration and the temperature. Increasing the pH from 2.0 to 9.5 caused a decrease in adsorption. However, the adsorption was increased by increasing the initial Cr(VI) concentration and temperature. The multilinear mathematical model was also developed to predict the Cr(VI) adsorption on activated carbon samples within the experimental conditions.

  3. CRYOGENIC ADSORPTION OF HYDROGEN ISOTOPES OVER NANO-STRUCTURED MATERIALS

    SciTech Connect

    Xiao, S.; Heung, L.

    2010-10-07

    Porous materials such as zeolites, activated carbon, silica gels, alumina and a number of industrial catalysts are compared and ranked for hydrogen and deuterium adsorption at liquid nitrogen temperature. All samples show higher D{sub 2} adsorption than that of H{sub 2}, in which a HY sample has the greatest isotopic effect while 13X has the highest hydrogen uptake capacity. Material's moisture content has significant impact to its hydrogen uptake. A material without adequate drying could result in complete loss of its adsorption capacity. Even though some materials present higher H{sub 2} adsorption capacity at full pressure, their adsorption at low vapor pressure may not be as good as others. Adsorption capacity in a dynamic system is much less than in a static system. A sharp desorption is also expected in case of temperature upset.

  4. Communication: Thermodynamic analysis of critical conditions of polymer adsorption

    SciTech Connect

    Cimino, R.; Neimark, A. V.; Rasmussen, C. J.

    2013-11-28

    Polymer adsorption to solid surfaces is a ubiquitous phenomenon, which has attracted long-lasting attention. Dependent on the competition between the polymer-solid adsorption and polymer-solvent solvation interactions, a chain may assume either 3d solvated conformation when adsorption is weak or 2d adsorbed conformation when adsorption is strong. The transition between these conformations occurring upon variation of adsorption strength is quite sharp, and in the limit of “infinite” chain length, can be treated as a critical phenomenon. We suggest a novel thermodynamic definition of the critical conditions of polymer adsorption from the equality of incremental chemical potentials of adsorbed and free chains. We show with the example of freely jointed Lennard-Jones chains tethered to an adsorbing surface that this new definition provides a link between thermodynamic and geometrical features of adsorbed chains and is in line with classical scaling relationships for the fraction of adsorbed monomers, chain radii of gyration, and free energy.

  5. Studies on adsorption of formaldehyde in zirconium phosphate-glyphosates

    NASA Astrophysics Data System (ADS)

    Zhang, Yuejuan; Yi, Jianjun; Xu, Qinghong

    2011-01-01

    In our previous work [22], a kind of layered compound of zirconium phosphate-glyphosate (ZrGP) was synthesized. Its large surface area (445 m 2/g) indicates this compound has possible application in adsorptions. In this paper, adsorption to formaldehyde in ZrGP and mechanisms of the adsorption were studied carefully. Balance time of adsorption (about 6 h) and largest adsorbed amount (7.8%) were found when adsorption temperature was at 40 °C and pH value of adsorption environment was about 3.0. H-bonds were found existing between molecules of formaldehyde and ZrGP, and formaldehyde molecules could exist in ZrGP stably.

  6. Adsorption characteristics of brilliant green dye on kaolin.

    PubMed

    Nandi, B K; Goswami, A; Purkait, M K

    2009-01-15

    Experimental investigations were carried out to adsorb toxic brilliant green dye from aqueous medium using kaolin as an adsorbent. Characterization of kaolin is done by measuring: (i) particle size distribution using particle size analyzer, (ii) BET surface area using BET surface analyzer, and (iii) structural analysis using X-ray diffractometer. The effects of initial dye concentration, contact time, kaolin dose, stirring speed, pH and temperature were studied for the adsorption of brilliant green in batch mode. Adsorption experiments indicate that the extent of adsorption is strongly dependent on pH of solution. Free energy of adsorption (DeltaG0), enthalpy (DeltaH0) and entropy (DeltaS0) changes are calculated to know the nature of adsorption. The calculated values of DeltaG0 at 299K and 323K indicate that the adsorption process is spontaneous. The estimated values of DeltaH0 and DeltaS0 both show the negative sign, which indicate that the adsorption process is exothermic and the dye molecules are organized on the kaolin surface in less randomly fashion than in solution. The adsorption kinetic has been described by first-order, pseudo-second-order and intra-particle-diffusion models. It was observed that the rate of dye adsorption follows pseudo-second-order model for the dye concentration range studied in the present case. Standard adsorption isotherms were used to fit the experimental equilibrium data. It was found that the adsorption of brilliant green on kaolin follows the Langmuir adsorption isotherm.

  7. Adsorption to fish sperm of vertically transmitted fish viruses

    USGS Publications Warehouse

    Mulcahy, D.; Pascho, R.J.

    1984-01-01

    More than 99 percent of a vertically transmitted fish rhabdovirus, infectious hematopoietic necrosis virus, was removed from suspension in less than 1 minute by adsorption to the surface membrane of sperm from two genera of salmonid fishes. The vertically transmitted, infectious pancreatic necrosis virus adsorbed to a lesser degree, but no adsorption occurred with a second fish rhabdovirus that is not vertically transmitted. Such adsorption may be involved in vertical transmission of these viruses.

  8. 40 CFR 268.42 - Treatment standards expressed as specified technologies.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... osmosis; and/or (5) incineration for the recovery of acid—Note: this does not preclude the use of other... technologies: (1) Ion exchange; (2) resin or solid (i.e., zeolites) adsorption; (3) reverse osmosis;...

  9. 40 CFR 268.42 - Treatment standards expressed as specified technologies.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... osmosis; and/or (5) incineration for the recovery of acid—Note: this does not preclude the use of other... technologies: (1) Ion exchange; (2) resin or solid (i.e., zeolites) adsorption; (3) reverse osmosis;...

  10. 40 CFR 268.42 - Treatment standards expressed as specified technologies.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... osmosis; and/or (5) incineration for the recovery of acid—Note: this does not preclude the use of other... technologies: (1) Ion exchange; (2) resin or solid (i.e., zeolites) adsorption; (3) reverse osmosis;...

  11. 40 CFR 268.42 - Treatment standards expressed as specified technologies.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... osmosis; and/or (5) incineration for the recovery of acid—Note: this does not preclude the use of other... technologies: (1) Ion exchange; (2) resin or solid (i.e., zeolites) adsorption; (3) reverse osmosis;...

  12. 40 CFR 268.42 - Treatment standards expressed as specified technologies.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... osmosis; and/or (5) incineration for the recovery of acid—Note: this does not preclude the use of other... technologies: (1) Ion exchange; (2) resin or solid (i.e., zeolites) adsorption; (3) reverse osmosis;...

  13. Effective surface areas of coals measured by dye adsorption

    SciTech Connect

    Spitzer, D.P.

    1988-01-01

    The primary interest has been to examine adsorption behavior especially at short contact times, ten minutes to an hour, to determine whether such measurements might give useful data on effective surface areas - i.e., the surface that would be accessible to reagents within times comparable to those typical of most coal processing. Accordingly, most of the emphasis is on the effect of time on adsorption, rather than on traditional adsorption isotherms. Although most literature on cationic dye adsorption (mostly on carbons) uses methylene blue, it happened that the authors originally used safranin O instead because this dye was reported to be useful in distinguishing oxidized coals from fresh coals. Many of their experiments were repeated using methylene blue (in water), with very similar results. It was noted early that swelling of coals in water was common, especially for more oxidized or lower rank coals, and adsorption experiments were also done in another solvent, namely methanol. This produced quite striking differences for some coals. Coal surfaces that are readily accessible to adsorption by safranin are found to correlate well with N/sub 2/ surface areas, with adsorption of 1.0 mg safranin per gram of coal corresponding to essentially a surface area of 1.0 m/sup 2//g. Highly oxidized coals were found to swell considerably in water, with correspondingly increased adsorption. Areas of such coals can be estimated by adsorption of safranin from methanol solutions.

  14. Adsorption of Ar on individual carbon nanotubes, graphene, and graphite

    NASA Astrophysics Data System (ADS)

    Dzyubenko, Boris; Kahn, Joshua; Vilches, Oscar; Cobden, David

    2015-03-01

    We compare and contrast results of adsorption measurements of Ar on single-walled carbon nanotubes, graphene, and graphite. Adsorption isotherms on individual suspended nanotubes were obtained using both the mechanical resonance frequency shift (sensitive to mass adsorption) and the electrical conductance. Isotherms on graphene mounted on hexagonal boron nitride were obtained using only the conductance. New volumetric adsorption isotherms on bulk exfoliated graphite were also obtained, paying special attention to the very low coverage region (less than 2% of a monolayer). This allowed us to compare the degree of heterogeneity on the three substrate types, the binding energies, and the van der Waals 2D parameters. Research supported by NSF DMR 1206208.

  15. Adsorption coefficients for TNT on soil and clay minerals

    NASA Astrophysics Data System (ADS)

    Rivera, Rosángela; Pabón, Julissa; Pérez, Omarie; Muñoz, Miguel A.; Mina, Nairmen

    2007-04-01

    To understand the fate and transport mechanisms of TNT from buried landmines is it essential to determine the adsorption process of TNT on soil and clay minerals. In this research, soil samples from horizons Ap and A from Jobos Series at Isabela, Puerto Rico were studied. The clay fractions were separated from the other soil components by centrifugation. Using the hydrometer method the particle size distribution for the soil horizons was obtained. Physical and chemical characterization studies such as cation exchange capacity (CEC), surface area, percent of organic matter and pH were performed for the soil and clay samples. A complete mineralogical characterization of clay fractions using X-ray diffraction analysis reveals the presence of kaolinite, goethite, hematite, gibbsite and quartz. In order to obtain adsorption coefficients (K d values) for the TNT-soil and TNT-clay interactions high performance liquid chromatography (HPLC) was used. The adsorption process for TNT-soil was described by the Langmuir model. A higher adsorption was observed in the Ap horizon. The Freundlich model described the adsorption process for TNT-clay interactions. The affinity and relative adsorption capacity of the clay for TNT were higher in the A horizon. These results suggest that adsorption by soil organic matter predominates over adsorption on clay minerals when significant soil organic matter content is present. It was found that, properties like cation exchange capacity and surface area are important factors in the adsorption of clayey soils.

  16. [Adsorption of Cd2+ on biochar from aqueous solution].

    PubMed

    Guo, Wen-juan; Liang, Xue-feng; Lin, Da-song; Xu, Ying-ming; Wang, Lin; Sun, Yue-bing; Qin, Xu

    2013-09-01

    Biomass-based materials such as biochar have a good performance in heavy metal adsorption. The adsorption of Cd2+ on biochar converted from cotton straw was studied. Adsorption isotherm, kinetics and effect factors such as temperature, pH and ionic strength were investigated. The adsorption of Cd2+ on biochar can be fitted by the Freundlich isotherm better than the Langmuir isotherm. The maximum adsorption amounts of Cd2+ at different temperatures were 9.738 mg x g(-1) (288.15 K), 10.14 mg x g(-1) (298.15 K), 10.40 mg x g(-1) (308.15 K) and 10.71 mg x g(-1) (318.15 K), respectively. The free energies AG(theta) were from -8.346 kJ x mol(-1) to -10.276 kJ x mol(-1) at different temperatures, indicating that the adsorption of Cd2+ onto biochar is spontaneous and is an endothermic process. The adsorption process can reach equilibrium within 40 minutes and can be fitted by the pseudo second order kinetic model. pH showed a significant effect on the adsorption of Cd2+ on biochar in the range of 2-8. The adsorption amount of Cd2+ on biochar shows a reducing trend with the increasing ionic strength.

  17. Adsorption of glucose, cellobiose, and cellotetraose onto cellulose model surfaces.

    PubMed

    Hoja, Johannes; Maurer, Reinhard J; Sax, Alexander F

    2014-07-31

    Reliable simulation of molecular adsorption onto cellulose surfaces is essential for the design of new cellulose nanocomposite materials. However, the applicability of classical force field methods to such systems remains relatively unexplored. In this study, we present the adsorption of glucose, cellobiose, and cellotetraose on model surfaces of crystalline cellulose Iα and Iβ. The adsorption of the two large carbohydrates was simulated with the GLYCAM06 force field. To validate this approach, quantum theoretical calculations for the adsorption of glucose were performed: Equilibrium geometries were studied with density functional theory (DFT) and dispersion-corrected DFT, whereas the adsorption energies were calculated with two standard density functional approximations and five dispersion-containing DFT approaches. We find that GLYCAM06 gives a good account of geometries and, in most cases, accurate adsorption energies when compared to dispersion-corrected DFT energies. Adsorption onto the (100) surface of cellulose Iα is, in general, stronger than onto the (100) surface of cellulose Iβ. Contrary to intuition, the adsorption energy is not directly correlated with the number of hydrogen bonds; rather, it is dominated by dispersion interactions. Especially for bigger adsorbates, a neglect of these interactions leads to a dramatic underestimation of adsorption energies.

  18. Adsorption of cellulase from Trichoderma viride on cellulose

    SciTech Connect

    Ooshima, H.; Sakata, M.; Harano, Y.

    1983-12-01

    The adsorption of cellulase from Trichoderma viride (Meicelase CEP) on the surface of pure cellulose was studied. The adsorption was found to obey apparently the Langmuir isotherm. From the data concerning the effects of temperature and the crystallinity of cellulose on the Langmuir adsorption parameters, the characteristics of the adsorption of the individual cellulase components, namely CMCase (endoglucanase) and Avicelase (exoglucanase), were discussed. While beta-glucosidase also adsorbed on the surface of cellulose at 5 degrees C, it did not at 50 degrees C. (Refs. 27).

  19. Adsorption properties and gaseous mercury transformation rate of natural biofilm.

    PubMed

    Cheng, Jinping; Zhao, Wenchang; Liu, Yuanyuan; Wu, Cheng; Liu, Caie; Wang, Wenhua

    2008-11-01

    Biofilms were developed on glass microscope slides in a natural aquatic environment and their mercury adsorption properties were evaluated. Results demonstrated that the biofilms contained a large number of bacterial cells and associated extracellular polymers. Mercury forms detected in the biofilms were mainly bound to residual matter and organic acids. The adsorption processes could be described by a Langmuir isotherm. The optimum conditions for adsorption of mercury to natural biofilm were an ionic strength of 0.1 mol/L, pH 6 and an optimum adsorption time of 40 min. The transformation rate was 0.79 microg gaseous mercury per gram of biofilm.

  20. Adsorption of malathion on thermally treated egg shell material.

    PubMed

    Elwakeel, Khalid Z; Yousif, Ahmed M

    2010-01-01

    Thermally treated egg shell materials were prepared at different temperatures. The samples were investigated by means of FT-IR and thermogravimetric analysis (TGA). The adsorption behaviour of malathion on egg shell and its thermally treated samples was studied using batch method and gave uptake capacities up to 0.964 mmol/g. Adsorption kinetics as well as the adsorption isotherms were discussed. Regeneration of the loaded adsorbent beads towards the successive cycles was also clarified. The adsorption of malathion is maintained until the third cycle without a significant activity loss.

  1. A continuum hard-sphere model of protein adsorption

    NASA Astrophysics Data System (ADS)

    Finch, Craig; Clarke, Thomas; Hickman, James J.

    2013-07-01

    Protein adsorption plays a significant role in biological phenomena such as cell-surface interactions and the coagulation of blood. Two-dimensional random sequential adsorption (RSA) models are widely used to model the adsorption of proteins on solid surfaces. Continuum equations have been developed so that the results of RSA simulations can be used to predict the kinetics of adsorption. Recently, Brownian dynamics simulations have become popular for modeling protein adsorption. In this work a continuum model was developed to allow the results from a Brownian dynamics simulation to be used as the boundary condition in a computational fluid dynamics (CFD) simulation. Brownian dynamics simulations were used to model the diffusive transport of hard-sphere particles in a liquid and the adsorption of the particles onto a solid surface. The configuration of the adsorbed particles was analyzed to quantify the chemical potential near the surface, which was found to be a function of the distance from the surface and the fractional surface coverage. The near-surface chemical potential was used to derive a continuum model of adsorption that incorporates the results from the Brownian dynamics simulations. The equations of the continuum model were discretized and coupled to a CFD simulation of diffusive transport to the surface. The kinetics of adsorption predicted by the continuum model closely matched the results from the Brownian dynamics simulation. This new model allows the results from mesoscale simulations to be incorporated into micro- or macro-scale CFD transport simulations of protein adsorption in practical devices.

  2. [Effects of dissolved organic matter on phenanthrene adsorption by soil].

    PubMed

    Xiong, Wei; Ling, Wan-ting; Gao, Yan-zheng; Li, Qiu-ling; Dai, Jing-yu

    2007-02-01

    This paper studied the effects of exotic and native dissolved organic matter (DOM) on the phenanthrene adsorption by three soils differed in soil organic carbon content (foc). The exotic DOM came from decayed rice straw, while the native DOM was extracted from the test soils. In all cases, the adsorption of phenanthrene by treated soils could be well described with linear-type model, and there was a positive correlation between adsorption coefficient (Kd) and foc Compared with the control, the Kd value of test soils after native DOM removed was increased by 7. 08% -21. 4% , and the increment (deltaKd) was positively correlated with fo,, indicating that the presence of soil native DOM impeded the phenanthrene adsorption by soil. The effects of exotic DOM on phenanthrene adsorption had a close relation with its added concentration in soil-water system. Within the range of 0-106 mg DOC x L(-1) , the K, value increased first, and then decreased with the increase of added exotic DOM concentration. Lower concentrations of added exotic DOM promoted the phenanthrene adsorption by soil, while higher concentrations ( I> or =52 mg DOC x L(-1)) of it obviously impeded this adsorption. These effects of exotic and native DOM on soil phenanthrene adsorption were considered to be related to the association of phenanthrene with DOM in solution, and the ' cumulative adsorption effect' between soil solid and aqueous phases.

  3. Synthesis and adsorption of functionalized polystyrenes

    SciTech Connect

    Iyengar, D.R.

    1992-12-31

    The effect of specifically interacting functional groups located at the chain ends of polystyrene on the absorption rate, adsorbance, graft density and surface excess are discussed from cyclohexane, a theta solvent and toluene. Polystyrenes with hydroxyl and carboxylic acid-end-groups in narrow molecular weight distribution are synthesized by anionic polymerization of styrene followed by suitable termination reactions. Thin layer chromatography (TLC) is developed as an analytical technique to predict trends in the adsorption of the polymers in a range of solvents. In particular the information about the localization of the end-group and therefore different chain architectures at the interface are inferred from this simple technique. Adsorption isotherms are obtained for each of the functionalized polymers of four different molecular weights, the selection of which was based on the TLC results. Kinetics of adsorption and the adsorbance data are determined by liquid counting of tritium labelled polymers. Graft density and surface excess data are calculated from the adsorbance data and other known parameters. It is shown, from these data, that polystyrenes with a carboxylic acid end-group form weakly stretched brushes at the glass-cyclohexane interface and mushrooms at the glass-toluene interface a result consistent with the higher osmotic repulsions towards packing in good solvents. Polystyrenes with function groups at both the chain ends are hypothesized to form a range of structures from those dominated by tails at higher concentrations to those dominated by loops and trains at lower solution concentrations. At higher molecular weights it is shown that functionalized a result consistent with the TLC predictions. Hydroxyl end-group is shown to be an ineffective sticky foot from its adsorbance vis-a-vis polystyrene.

  4. ION EXCHANGE ADSORPTION PROCESS FOR PLUTONIUM SEPARATION

    DOEpatents

    Boyd, G.E.; Russell, E.R.; Taylor, M.D.

    1961-07-11

    Ion exchange processes for the separation of plutonium from fission products are described. In accordance with these processes an aqueous solution containing plutonium and fission products is contacted with a cation exchange resin under conditions favoring adsorption of plutonium and fission products on the resin. A portion of the fission product is then eluted with a solution containing 0.05 to 1% by weight of a carboxylic acid. Plutonium is next eluted with a solution containing 2 to 8 per cent by weight of the same carboxylic acid, and the remaining fission products on the resin are eluted with an aqueous solution containing over 10 per cent by weight of sodium bisulfate.

  5. Fractional statistical theory of finite multilayer adsorption

    NASA Astrophysics Data System (ADS)

    Takara, E. A.; Quiroga, E.; Matoz-Fernandez, D. A.; Ochoa, N. A.; Ramirez-Pastor, A. J.

    2016-01-01

    In the present paper, finite multilayer adsorption is described as a fractional statistics problem, based on Haldane's statistics. In this scheme, the Helmholtz free energy and its derivatives are written in terms of a parameter g, which relates to the configuration of the molecules in the adsorbed state. For values of g ranging between 0 and 1 the formalism is used to model experimental data of bovine serum albumin (BSA) adsorbed onto an ion exchange resin for different values of pH and temperature. Excellent agreement between theory and experiments was found.

  6. Cadmium-109 Radioisotope Adsorption onto Polypyrrole Coated Sawdust of Dryobalanops aromatic: Kinetics and Adsorption Isotherms Modelling

    PubMed Central

    Olatunji, Michael Adekunle; Khandaker, Mayeen Uddin; Amin, Yusoff Mohd; Mahmud, Habibun Nabi Muhammad Ekramul

    2016-01-01

    A radiotracer study was conducted to investigate the removal characteristics of cadmium (109Cd) from aqueous solution by polypyrrole/ sawdust composite. Several factors such as solution pH, sorbent dosage, initial concentration, contact time, temperature and interfering metal ions were found to have influence on the adsorption process. The kinetics of adsorption was relatively fast, reaching equilibrium within 3 hours. A lowering of the solution pH reduced the removal efficiency from 99.3 to ~ 46.7% and an ambient temperature of 25°C was found to be optimum for maximum adsorption. The presence of sodium and potassium ions inhibited 109Cd removal from its aqueous solution. The experimental data for 109Cd adsorption showed a very good agreement with the Langmuir isotherm and a pseudo-first order kinetic model. The surface condition of the adsorbent before and after cadmium loading was investigated using BET, FESEM and FTIR. Considering the low cost of the precursor’s materials and the toxicity of 109Cd radioactive metal, polypyrrole synthesized on the sawdust of Dryobalanops aromatic could be used as an efficient adsorbent for the removal of 109Cd radioisotope from radionuclide-containing effluents. PMID:27706232

  7. Cadmium-109 Radioisotope Adsorption onto Polypyrrole Coated Sawdust of Dryobalanops aromatic: Kinetics and Adsorption Isotherms Modelling.

    PubMed

    Olatunji, Michael Adekunle; Khandaker, Mayeen Uddin; Amin, Yusoff Mohd; Mahmud, Habibun Nabi Muhammad Ekramul

    2016-01-01

    A radiotracer study was conducted to investigate the removal characteristics of cadmium (109Cd) from aqueous solution by polypyrrole/ sawdust composite. Several factors such as solution pH, sorbent dosage, initial concentration, contact time, temperature and interfering metal ions were found to have influence on the adsorption process. The kinetics of adsorption was relatively fast, reaching equilibrium within 3 hours. A lowering of the solution pH reduced the removal efficiency from 99.3 to ~ 46.7% and an ambient temperature of 25°C was found to be optimum for maximum adsorption. The presence of sodium and potassium ions inhibited 109Cd removal from its aqueous solution. The experimental data for 109Cd adsorption showed a very good agreement with the Langmuir isotherm and a pseudo-first order kinetic model. The surface condition of the adsorbent before and after cadmium loading was investigated using BET, FESEM and FTIR. Considering the low cost of the precursor's materials and the toxicity of 109Cd radioactive metal, polypyrrole synthesized on the sawdust of Dryobalanops aromatic could be used as an efficient adsorbent for the removal of 109Cd radioisotope from radionuclide-containing effluents.

  8. Modeling oxyanion adsorption on ferralic soil, part 2: chromate, selenate, molybdate, and arsenate adsorption.

    PubMed

    Pérez, Claudio; Antelo, Juan; Fiol, Sarah; Arce, Florencio

    2014-10-01

    High levels of oxyanions are found in the soil environment, often as a result of human activity. At high concentrations, oxyanions can be harmful to both humans and wildlife. Information about the interactions between oxyanions and natural samples is essential for understanding the bioavailability, toxicity, and transport of these compounds in the environment. In the present study, the authors investigated the reactivity of different oxyanions (AsO4 , MoO4 , SeO4 , and CrO4 ) at different pH values in 2 horizons of a ferralic soil. By combining available microscopic data on iron oxides with the macroscopic data obtained, the authors were able to use the charge distribution model to accurately describe the adsorption of these 4 oxyanions and thus to determine the surface speciation. The charge distribution model was previously calibrated and evaluated using phosphate adsorption/desorption data. The adsorption behavior on ferralic soil is controlled mainly by the natural iron oxides present, and it is qualitatively analogous to that exhibited by synthetic iron oxides. The highest adsorption was found for arsenate ions, whereas the lowest was found for selenate, with chromate and molybdate ions showing an intermediate behavior.

  9. Adsorption and co-adsorption of diclofenac and Cu(II) on calcareous soils.

    PubMed

    Graouer-Bacart, Mareen; Sayen, Stéphanie; Guillon, Emmanuel

    2016-02-01

    Pharmaceuticals are emerging contaminants and their presence in different compartments of the environment has been detected in many countries. In this study, laboratory batch experiments were conducted to characterize the adsorption of diclofenac, a widely used non-steroidal anti-inflammatory drug, on six calcareous soils. The adsorption of diclofenac was relatively low, which may lead to a risk of groundwater contamination and plant uptake. A correlation between the soil-water distribution coefficient Kd and soil characteristics has been highlighted. Indeed, diclofenac adsorption as a function of soil organic matter content (% OM) and Rt=% CaCO3/% OM was successfully described through a simple empirical model, indicating the importance of considering the inhibiting effect of CaCO3 on OM retention properties for a better assessment of diclofenac fate in the specific case of calcareous soils. The simultaneous co-adsorption of diclofenac and copper - a ubiquitous pollutant in the environment - at the water/soil interface, was also investigated. It appeared quite unexpectedly that copper did not have a significant influence on diclofenac retention.

  10. Equilibrium and kinetic adsorption study of the adsorptive removal of Cr(VI) using modified wheat residue.

    PubMed

    Chen, Suhong; Yue, Qinyan; Gao, Baoyu; Xu, Xing

    2010-09-01

    A new adsorbent modified from wheat residue was synthesized after reaction with epichlorohydrin and triethylamine by using the modifying agents of diethylenetriamine in the presence of organic medium of N,N-dimethylformamide. The performance of the modified wheat straw (MWS) was characterized by Fourier transform infrared spectroscopy and point of zero charge analysis. The adsorption was investigated in a batch adsorption system, including both equilibrium adsorption isotherms and kinetics. Results showed that MWR had great anion-adsorbing capacity, due to the existence of a large number of introduced amino groups, and the value of pH(PZC) was around 5.0. Equilibrium data were analyzed using the Langmuir, Freundlich, and Temkin isotherm models and were found to be best represented by the Freundlich isotherm model. Evaluation of the adsorption process identified its endothermic nature. The maximum adsorption capacity of MWS for the removal of Cr(VI) was 322.58mg/g at 328K, indicating that MWS has high chromium removal efficiency, compared to other adsorbents reported. The kinetics of adsorption followed the pseudo-second-order kinetic equation. The mechanism of adsorption was investigated using the intraparticle diffusion model. Thermodynamic parameters (free energy change, enthalpy change, and entropy change) revealed that the adsorption of Cr(VI) onto MWS was endothermic and spontaneous; additionally, the adsorption can be characterized as an ion-exchange process. The results suggest that MWS is an inexpensive and efficient adsorbent for removing Cr(VI) ions from aqueous solution.

  11. Effect of complexing ligands on the adsorption of Cu(II) onto the silica gel surface. 1: Adsorption of ligands

    SciTech Connect

    Park, Y.J.; Jung, K.H.; Park, K.K.; Park, K.K.

    1995-04-01

    The adsorption of several ligands on silica gel was investigated in aqueous solutions. The ligands used were 2,2{prime},6{prime},2{double_prime}-terpyridine, pyridine, 3,4-lutidine, 2-aminomethyl pyridine, 2-pyridine methanol, picolinic acid, salicylic acid, and 5-sulfosalicylic acid. The adsorption behaviors of these ligands were interpreted by means of three adsorption modes: ion exchange, hydrogen bonding, and hydrophobic interaction. For 2,2{prime},6{prime},2{double_prime}-terpyridine, pyridine, and 3,4-lutidine, the adsorption maxima appeared near their respective pK{sub a} values and were found to be due mainly to ion exchange, whereas the adsorption of these ligands at low pH was strongly attributed to hydrophobic interaction. The adsorption of 2-aminomethyl pyridine increased with increasing pH over the entire pH range investigated and was due mainly to ion exchange. Picolinic acid was adsorbed mainly by hydrogen bonding either via pyridine N atoms at low pH or via carboxylic O atoms at high pH. 2-Pyridine methanol was adsorbed by hydrophobic interaction at low pH and by hydrogen bonding at high pH. The adsorptions of salicylic and 5-sulfosalicylic acid were very small over the entire pH ranges investigated. For the adsorption mechanism, the Stern model was used to fit adsorption data.

  12. A compact low-temperature single crystal adsorption calorimetry setup for measuring coverage dependent heats of adsorption at cryogenic temperatures.

    PubMed

    Hörtz, Peter; Schäfer, Rolf

    2014-07-01

    Here we present the modification of an already existing Single Crystal Adsorption Calorimetry (SCAC) apparatus which has been extended by a compact cooling system to measure the coverage dependent heats of adsorption of gaseous compounds on thin metal substrates in a temperature range from 80 K to 430 K. The setup is characterized and its performance is tested by studying the adsorption of CO on Pt(111) at 150 K and 300 K. Coverage dependent sticking probabilities and heat of adsorption measurements are compared to previous experimental and theoretical studies proving the reliability of our compact low-temperature-SCAC setup.

  13. Studies on adsorption characteristics and mechanism of adsorption of chlorhexidine mainly by carbon black.

    PubMed

    Akaho, E; Fukumori, Y

    2001-09-01

    The extent of adsorption of chlorhexidine to carbon black and sanitary cotton was determined by measuring the amounts of chlorhexidine adsorbed to carbon black or sanitary cotton from the chlorhexidine solution containing specific amount of carbon black or sanitary cotton. As another comparative antiseptic example of adsorption phenomena, adsorption of acrinol to sanitary cotton was also studied. The specific surface area of carbon black was measured by the BET method of adsorption isotherm. The pattern of adsorption of chlorhexidine to carbon black was temperature-dependent Langmuir isotherms, and the amounts adsorbed increased as the temperature was raised. Since chlorhexidine, whose pKa's are 2.2 and 10.3, is considered to exist in aqueous solution as the di-cation, an ion-ion interaction should be formed between protonated biguanide and anionic portions of carbon black or sanitary cotton. The chlorophenyl and hexane moieties interact with hydrophobic portions of carbon black or sanitary cotton. The perturbation experiment conducted on this interaction system showed that the nature of interaction was irreversible. The enthalpy change calculated from Langmuir constants was small, indicating the existence of ion-ion interaction. The entropy values, 27.4 to 28.2 e.u. obtained in this system, suggested that the hydration shells of the ions were rather tightly bound. The area occupied by a chlorhexidine molecule, 548 (A)(2), was twice greater than the projection area, 276 (A)(2), suggesting that chlorhexidine was adsorbed in such a way that each molecule is sufficiently well spaced.

  14. Mechanism of Cr(VI) adsorption by coir pith studied by ESR and adsorption kinetic.

    PubMed

    Suksabye, Parinda; Nakajima, Akira; Thiravetyan, Paitip; Baba, Yoshinari; Nakbanpote, Woranan

    2009-01-30

    The oxidation state of chromium in coir pith after Cr(VI) adsorption from aqueous solution was investigated using electron spin resonance (ESR). To elucidate the mechanism of chromium adsorption on coir pith, the adsorption studies of Cr(VI) onto lignin, alpha-cellulose and holocellulose extracted from coir pith were also studied. ESR signals of Cr(V) and Cr(III) were observed in coir pith adsorbed Cr(VI) at solution pH 2, while ESR spectra of lignin extracted from coir pith revealed only the Cr(III) signal. In addition, ESR signal of Cr(V) was observed in alpha-cellulose and holocellulose extracted from coir pith adsorbed Cr(VI). These results confirmed that lignin in coir pith reduced Cr(VI) to Cr(III) while alpha-cellulose and holocellulose extracted from coir pith reduced Cr(VI) to Cr(V). The Cr(V) signal exhibited in ESR of alpha-cellulose and holocellulose might be bound with glucose in cellulose part of coir pith. In addition, xylose which is main in pentosan part of coir pith, indicated that it is involved in form complex with Cr(V) on coir pith. The adsorption kinetic of Cr(VI) from aqueous solution on coir pith was also investigated and described well with pseudo second order model. ESR and desorption experiments confirmed that Cr(VI), Cr(V) and Cr(III), exist in coir pith after Cr(VI) adsorption. The desorption data indicated that the percentage of Cr(VI), Cr(V) and Cr(III) in coir pith were 15.63%, 12.89% and 71.48%, respectively.

  15. Assessment of multi-mycotoxin adsorption efficacy of grape pomace.

    PubMed

    Avantaggiato, Giuseppina; Greco, Donato; Damascelli, Anna; Solfrizzo, Michele; Visconti, Angelo

    2014-01-15

    Grape pomace (pulp and skins) was investigated as a new biosorbent for removing mycotoxins from liquid media. In vitro adsorption experiments showed that the pomace obtained from Primitivo grapes is able to sequester rapidly and simultaneously different mycotoxins. Aflatoxin B1 (AFB1) was the most adsorbed mycotoxin followed by zearalenone (ZEA), ochratoxin A (OTA), and fumonisin B1 (FB1), whereas the adsorption of deoxynivalenol (DON) was negligible. AFB1 and ZEA adsorptions were not affected by changing pH values in the pH 3-8 range, whereas OTA and FB1 adsorptions were significantly affected by pH. Equilibrium adsorption isotherms obtained at different temperatures (5-70 °C) and pH values (3 and 7) were modeled and evaluated using the Freundlich, Langmuir, Sips, and Hill models. The goodness of the fits and the parameters involved in the adsorption mechanism were calculated by the nonlinear regression analysis method. The best-fitting models to describe AFB1, ZEA, and OTA adsorption by grape pomace were the Sips, Langmuir, and Freundlich models, respectively. The Langmuir and Sips models were the best models for FB1 adsorption at pH 7 and 3, respectively. The theoretical maximum adsorption capacities (mmol/kg dried pomace) calculated at pH 7 and 3 decreased in the following order: AFB1 (15.0 and 15.1) > ZEA (8.6 and 8.3) > OTA (6.3-6.9) > FB1 (2.2 and 0.4). Single- and multi-mycotoxin adsorption isotherms showed that toxin adsorption is not affected by the simultaneous presence of different mycotoxins in the liquid medium. The profiles of adsorption isotherms obtained at different temperatures and pH and the thermodynamic parameters (ΔG°, ΔH°, ΔS°) suggest that mycotoxin adsorption is an exothermic and spontaneous process, which involves physisorption weak associations. Hydrophobic interactions may be associated with AFB1 and ZEA adsorption, whereas polar noncovalent interactions may be associated with OTA and FB1 adsorption. In conclusion, this study

  16. Functionalized mesoporous silica materials for molsidomine adsorption: Thermodynamic study

    SciTech Connect

    Alyoshina, Nonna A.; Parfenyuk, Elena V.

    2013-09-15

    A series of unmodified and organically modified mesoporous silica materials was prepared. The unmodified mesoporous silica was synthesized via sol–gel synthesis in the presence of D-glucose as pore-forming agent. The functionalized by phenyl, aminopropyl and mercaptopropyl groups silica materials were prepared via grafting. The fabricated adsorbent materials were characterized by Fourier transform infrared spectroscopy (FTIR) analysis, N{sub 2} adsorption/desorption and elemental analysis methods. Then their adsorption properties for mesoionic dug molsidomine were investigated at 290–313 K and physiological pH value. Thermodynamic parameters of molsidomine adsorption on the synthesized materials have been calculated. The obtained results showed that the adsorption process of molsidomine on the phenyl modified silica is the most quantitatively and energetically favorable. The unmodified and mercaptopropyl modified silica materials exhibit significantly higher adsorption capacities and energies for molsidomine than the aminopropyl modified sample. The effects are discussed from the viewpoint of nature of specific interactions responsible for the adsorption. - Graphical abstract: Comparative analysis of the thermodynamic characteristics of molsidomine adsorption showed that the adsorption process on mesoporous silica materials is controlled by chemical nature of surface functional groups. Molsidomine adsorption on the phenyl modified silica is the most quantitatively and energetically favorable. Taking into account ambiguous nature of mesoionic compounds, it was found that molsidomine is rather aromatic than dipolar. Display Omitted - Highlights: • Unmodified and organically modified mesoporous silica materials were prepared. • Molsidomine adsorption on the silica materials was studied. • Phenyl modified silica shows the highest adsorption capacity and favorable energy. • Molsidomine exhibits the lowest affinity to aminopropyl modified silica.

  17. Adsorption of dimeric surfactants in lamellar silicates

    NASA Astrophysics Data System (ADS)

    Balcerzak, Mateusz; Pietralik, Zuzanna; Domka, Ludwik; Skrzypczak, Andrzej; Kozak, Maciej

    2015-12-01

    The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay - hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1‧-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d001) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH2 and CH3 groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  18. Atomic and Molecular Adsorption on Re(0001)

    SciTech Connect

    Hahn, Konstanze; Mavrikakis, Manos

    2014-02-01

    Using periodic, self-consistent density functional theory calculations, the adsorption of several atomic (H, S, N, O and C) and molecular (CO2, N2, NH3, HCN, CO and NO) species and molecular fragments (NH2, NH, CN, CNH2, HNO, NOH, CH3, CH2, CH and OH) on the (0001) facet of rhenium at a coverage of 0.25 ML has been studied. Preferred binding sites with their corresponding binding energy and deformation energy of the surface, as well as an estimated diffusion barrier of each species have been determined. Atomic species and molecular fragments tend to bind to threefold sites, whereas molecular species tend to bind to top sites. The binding strength, with respect to the corresponding gas phase species and in increasing order for all species studied, is: CO2 < N2 < NH3 < CO < CH3 < HCN < NO < H < NH2 < OH < CH2 < CNH2 < CN < HNO < NH < NOH < S < N < O < CH < C. The vibrational frequencies of all species in their most energetically favorable adsorbed configuration have been calculated. Finally, the thermochemistry of adsorption and decomposition of NO, NO + H, NH3, N2, CO2, CO and CH4 on Re(0001) has been analyzed.

  19. Trichloroethylene (TCE) adsorption using sustainable organic mulch.

    PubMed

    Wei, Zongsu; Seo, Youngwoo

    2010-09-15

    Soluble substrates (electron donors) have been commonly injected into chlorinated solvent contaminated plume to stimulate reductive dechlorination. Recently, different types of organic mulches with economic advantages and sustainable benefits have received much attention as new supporting materials that can provide long term sources of electron donors for chlorinated solvent bioremediation in engineered biowall systems. However, sorption capacities of organic mulches for chlorinated solvents have not been studied yet. In this study, the physiochemical properties of organic mulches (pine, hardwood and cypress mulches) were measured and their adsorption capacity as a potential media was elucidated. Single, binary and quaternary isotherm tests were conducted with trichloroethylene (TCE), tetrachloroethylene (PCE), trans-dichloroethylene (trans-DCE) and cis-dichloroethylene (cis-DCE). Among the three tested mulches, pine mulch showed the highest sorption capacity for the majority of the tested chemicals in single isotherm test. In binary or quaternary isotherm tests, competition among chemicals appears to diminish the differences in Q(e) for tested mulches. However, pine mulch also showed higher adsorption capacity for most chemicals when compared to hardwood and cypress mulches in the two isotherm tests. Based upon physicochemical properties of the three mulches, higher sorption capacity of pine mulch over hardwood and cypress mulches appears to be attributed to a higher organic carbon content and the lower polarity.

  20. Model carcinogen adsorption dynamics of DNA gel.

    PubMed

    Tomita, Naoko; Naito, Daisuke; Rokugawa, Isamu; Yamamoto, Takao; Dobashi, Toshiaki

    2014-09-01

    We have derived theoretical equations describing the adsorption of carcinogen to gels in an immersion medium containing carcinogens. The theory was developed for a cylindrical boundary condition under the assumption of a carcinogen diffusion-limited process combined with the "moving boundary picture (Furusawa et al., 2007)". The time course of the adsorbed carcinogen layer thickness and that of the carcinogen concentration in an immersion medium were expressed by a set of scaled variables, and the asymptotic behavior in the initial stage was derived. Experiments based on the theory were performed using a DNA gel sandwiched between a set of coverglasses in a medium containing acridine orange (AO). The boundary between the AO-adsorbed gel layer and AO-nonadsorbed gel layer was traced during the immersion. The time courses of the AO-adsorbed gel layer thickness and the AO concentration in the immersion medium were well explained by the theory, and the number ratio of the total AO molecules to the adsorption sites in the DNA gel was determined.

  1. Particle morphology effects in random sequential adsorption

    NASA Astrophysics Data System (ADS)

    Budinski-Petković, Lj.; Lončarević, I.; Dujak, D.; Karač, A.; Šćepanović, J. R.; Jakšić, Z. M.; Vrhovac, S. B.

    2017-02-01

    The properties of the random sequential adsorption of objects of various shapes on a two-dimensional triangular lattice are studied numerically by means of Monte Carlo simulations. The depositing objects are formed by self-avoiding lattice steps, whereby the size of the objects is gradually increased by wrapping the walks in several different ways. The aim of this work is to investigate the impact of the geometrical properties of the shapes on the jamming density θJ and on the temporal evolution of the coverage fraction θ (t ) . Our results suggest that the order of symmetry axis of a shape exerts a decisive influence on adsorption kinetics near the jamming limit θJ. The decay of probability for the insertion of a new particle onto a lattice is described in a broad range of the coverage θ by the product between the linear and the stretched exponential function for all examined objects. The corresponding fitting parameters are discussed within the context of the shape descriptors, such as rotational symmetry and the shape factor (parameter of nonsphericity) of the objects. Predictions following from our calculations suggest that the proposed fitting function for the insertion probability is consistent with the exponential approach of the coverage fraction θ (t ) to the jamming limit θJ.

  2. Enhanced adsorption and recovery of uranyl ions by NikR mutant-displaying yeast.

    PubMed

    Kuroda, Kouichi; Ebisutani, Kazuki; Iida, Katsuya; Nishitani, Takashi; Ueda, Mitsuyoshi

    2014-04-11

    Uranium is one of the most important metal resources, and the technology for the recovery of uranyl ions (UO22+) from aqueous solutions is required to ensure a semi-permanent supply of uranium. The NikR protein is a Ni2+-dependent transcriptional repressor of the nickel-ion uptake system in Escherichia coli, but its mutant protein (NikRm) is able to selectively bind uranyl ions in the interface of the two monomers. In this study, NikRm protein with ability to adsorb uranyl ions was displayed on the cell surface of Saccharomyces cerevisiae. To perform the binding of metal ions in the interface of the two monomers, two metal-binding domains (MBDs) of NikRm were tandemly fused via linker peptides and displayed on the yeast cell surface by fusion with the cell wall-anchoring domain of yeast α-agglutinin. The NikRm-MBD-displaying yeast cells with particular linker lengths showed the enhanced adsorption of uranyl ions in comparison to the control strain. By treating cells with citrate buffer (pH 4.3), the uranyl ions adsorbed on the cell surface were recovered. Our results indicate that the adsorption system by yeast cells displaying tandemly fused MBDs of NikRm is effective for simple and concentrated recovery of uranyl ions, as well as adsorption of uranyl ions.

  3. Improving the hydrogen oxidation reaction rate by promotion of hydroxyl adsorption

    NASA Astrophysics Data System (ADS)

    Strmcnik, Dusan; Uchimura, Masanobu; Wang, Chao; Subbaraman, Ram; Danilovic, Nemanja; van der Vliet, Dennis; Paulikas, Arvydas P.; Stamenkovic, Vojislav R.; Markovic, Nenad M.

    2013-04-01

    The development of hydrogen-based energy sources as viable alternatives to fossil-fuel technologies has revolutionized clean energy production using fuel cells. However, to date, the slow rate of the hydrogen oxidation reaction (HOR) in alkaline environments has hindered advances in alkaline fuel cell systems. Here, we address this by studying the trends in the activity of the HOR in alkaline environments. We demonstrate that it can be enhanced more than fivefold compared to state-of-the-art platinum catalysts. The maximum activity is found for materials (Ir and Pt0.1Ru0.9) with an optimal balance between the active sites that are required for the adsorption/dissociation of H2 and for the adsorption of hydroxyl species (OHad). We propose that the more oxophilic sites on Ir (defects) and PtRu material (Ru atoms) electrodes facilitate the adsorption of OHad species. Those then react with the hydrogen intermediates (Had) that are adsorbed on more noble surface sites.

  4. Enhanced Adsorption and Recovery of Uranyl Ions by NikR Mutant-Displaying Yeast

    PubMed Central

    Kuroda, Kouichi; Ebisutani, Kazuki; Iida, Katsuya; Nishitani, Takashi; Ueda, Mitsuyoshi

    2014-01-01

    Uranium is one of the most important metal resources, and the technology for the recovery of uranyl ions (UO22+) from aqueous solutions is required to ensure a semi-permanent supply of uranium. The NikR protein is a Ni2+-dependent transcriptional repressor of the nickel-ion uptake system in Escherichia coli, but its mutant protein (NikRm) is able to selectively bind uranyl ions in the interface of the two monomers. In this study, NikRm protein with ability to adsorb uranyl ions was displayed on the cell surface of Saccharomyces cerevisiae. To perform the binding of metal ions in the interface of the two monomers, two metal-binding domains (MBDs) of NikRm were tandemly fused via linker peptides and displayed on the yeast cell surface by fusion with the cell wall-anchoring domain of yeast α-agglutinin. The NikRm-MBD-displaying yeast cells with particular linker lengths showed the enhanced adsorption of uranyl ions in comparison to the control strain. By treating cells with citrate buffer (pH 4.3), the uranyl ions adsorbed on the cell surface were recovered. Our results indicate that the adsorption system by yeast cells displaying tandemly fused MBDs of NikRm is effective for simple and concentrated recovery of uranyl ions, as well as adsorption of uranyl ions. PMID:24970221

  5. A feasible way to remove the heat during adsorptive methane storage.

    PubMed

    Gütlein, Stefan; Burkard, Christoph; Zeilinger, Johannes; Niedermaier, Matthias; Klumpp, Michael; Kolb, Veronika; Jess, Andreas; Etzold, Bastian J M

    2015-01-06

    Methane originating from biogas or natural gas is an attractive and environmentally friendly alternative to gasoline. Adsorption is seen as promising storage technology, but the heat released limits fast filling of these systems. Here a lab scale adsorptive methane storage tank, capable to study the temperature increase during fast filling, was realized. A variation of the filling time from 1 h to 31 s, showed a decrease of the storage capacity of 14% and temperature increase of 39.6 °C. The experimental data could be described in good accordance with a finite element simulation solving the transient mass, energy, and impulse balance. The simulation was further used to extrapolate temperature development in real sized car tanks and for different heat pipe scenarios, resulting in temperature rises of approximately 110 °C. It could be clearly shown, that with heat conductivity as solei mechanism the heat cannot be removed in acceptable time. By adding an outlet to the tank a feed flow cooling with methane as heat carrier was realized. This setup was proofed in simulation and lab scale experiments to be a promising technique for fast adsorbent cooling and can be crucial to leverage the full potential of adsorptive methane gas storage.

  6. [Adsorption of perfluorooctanesulfonate (PFOS) onto modified activated carbons].

    PubMed

    Tong, Xi-Zhen; Shi, Bao-You; Xie, Yue; Wang, Dong-Sheng

    2012-09-01

    Modified coal and coconut shell based powdered activated carbons (PACs) were prepared by FeCl3 and medium power microwave treatment, respectively. Batch experiments were carried out to evaluate the characteristics of adsorption equilibrium and kinetics of perfluorooctanesulfonate (PFOS) onto original and modified PACs. Based on pore structure and surface functional groups characterization, the adsorption behaviors of modified and original PACs were compared. The competitive adsorption of humic acid (HA) and PFOS on original and modified coconut shell PACs were also investigated. Results showed that both Fe3+ and medium power microwave treatments changed the pore structure and surface functional groups of coal and coconut shell PACs, but the changing effects were different. The adsorption of PFOS on two modified coconut shell-based PACs was significantly improved. While the adsorption of modified coal-based activated carbons declined. The adsorption kinetics of PFOS onto original and modified coconut shell-based activated carbons were the same, and the time of reaching adsorption equilibrium was about 6 hours. In the presence of HA, the adsorption of PFOS by modified PAC was reduced but still higher than that of the original.

  7. Adsorption of mercury on laterite from Guizhou Province, China.

    PubMed

    Yu, Xiaohong; Zhu, Lijun; Guo, Baiwei; He, Shouyang

    2008-01-01

    The adsorption behaviors of Hg(II) on laterite from Guizhou Province, China, were studied and the adsorption mechanism was discussed. The results showed that different mineral compositons in the laterite will cause differences in the adsorption capacity of laterite to Hg(II). Illite and non-crystalloids are the main contributors to enhancing the adsorption capacity of laterite to Hg(II). The pH of the solution is an important factor affecting the adsorption of Hg(II) on laterite. The alkalescent environment (pH 7-9) is favorable to the adsorption of Hg(II). The amount of adsorbed Hg(II) increases with increasing pH. When the pH reaches a certain value, the amount of the adsorbed Hg(II) will reach the maximum level. The amount of adsorbed Hg(II) decreases with increasing pH. The optimal pHs of laterite and kaolinite are 9 and 8, respectively. The optimal initial concentrations of Hg(II) on laterite and kaolinite are 250 and 200 microg/ml, respectively. The adsorption isotherms were described by the Langmuir model. The adsorption of Hg(II) on laterite is a quick process while that of Hg(II) on kaolinite is a slow reaction. Laterite from Guizhou Province is a promising environmental material which can be used in the removal of Hg(II) from wastewater.

  8. Adsorption dynamics of molecular nitrogen at an Fe(111) surface.

    PubMed

    Nosir, M A; Martin-Gondre, L; Bocan, G A; Díez Muiño, R

    2017-03-08

    We present an extensive theoretical study of N2 adsorption mechanisms on an Fe(111) surface. We combine the static analysis of a six-dimensional potential energy surface (6D-PES), based on ab initio density functional theory (DFT) calculations for the system, with quasi-classical trajectory (QCT) calculations to simulate the adsorption dynamics. There are four molecular adsorption states, usually called γ, δ, α, and ε, arising from our DFT calculations. We find that N2 adsorption in the γ-state is non-activated, while the threshold energy is associated with the entrance channel for the other three adsorption states. Our QCT calculations confirm that there are activated and nonactivated paths for the adsorption of N2 on the Fe(111) surface, which is in agreement with previous experimental investigations. Molecular dynamics at a surface temperature Ts = 300 K and impact energies Ei in the 0-5 eV range show the relative occupancy of the γ, δ, α, and ε states. The δ-state, however, is only marginally populated despite its adsorption energy being very similar to that of the γ-state. Our QCT calculations trace the dependence of molecular trapping on the surface temperature Ts and initial impact energy Ei and quantify the rates of the different competitive channels that eventually lead to molecular adsorption.

  9. [Adsorption of Congo red from aqueous solution on hydroxyapatite].

    PubMed

    Zhan, Yan-Hui; Lin, Jian-Wei

    2013-08-01

    The adsorption of Congo red (CR) from aqueous solution on hydroxyapatite was investigated using batch experiments. The hydroxyapatite was effective for CR removal from aqueous solution. The adsorption kinetics of CR on hydroxyapatite well followed a pseudo-second-order model. The equilibrium adsorption data of CR on hydroxyapatite could be described by the Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models. Thermodynamic parameters such as Gibbs free energy change, enthalpy change and entropy change were calculated and showed that the adsorption of CR on hydroxyapatite was spontaneous and exothermic in nature. The CR adsorption capacity for hydroxyapatite decreased significantly with increasing pH from 8 to 10. Thermal regeneration showed that hydroxyapatite could be used for six desorption-adsorption cycles with high removal efficiency for CR in each cycle. The mechanisms for CR adsorption on hydroxyapatite with pH value below the pH at point of zero charge (pH(PZC)) include electrostatic attraction, hydrogen bonding and Lewis acid-base interaction. The mechanisms for CR adsorption on hydroxyapatite with pH value above its pH(PZC) include hydrogen bonding and Lewis acid-base interaction. Results of this work indicate that hydroxyapatite is a promising adsorbent for CR removal from aqueous solution.

  10. Derivation of the Freundlich Adsorption Isotherm from Kinetics

    ERIC Educational Resources Information Center

    Skopp, Joseph

    2009-01-01

    The Freundlich adsorption isotherm is a useful description of adsorption phenomena. It is frequently presented as an empirical equation with little theoretical basis. In fact, a variety of derivations exist. Here a new derivation is presented using the concepts of fractal reaction kinetics. This derivation provides an alternative basis for…

  11. Adsorption of Pyrene onto the Agricultural By-Product: Corncob.

    PubMed

    Li, Xiaojun; Tong, Dongli; Allinson, Graeme; Jia, Chunyun; Gong, Zongqing; Liu, Wan

    2016-01-01

    The adsorption behavior of pyrene on corncob was studied to provide a theoretical basis for the possible use of this material as an immobilized carrier for improving the bioremediation of PAH-contaminated soil. The results were as follows. Kinetic experiments showed that the adsorption processes obeyed a pseudo-second-order model. The intraparticle diffusion of Weber-Morris model fitting showed that the film and intraparticle diffusions were the key rate-limiting processes, and the adsorption process mainly consisted of three steps: boundary layer diffusion and two intra-particle diffusions. Experimental adsorption data for pyrene were successfully described by the adsorption-partition equilibrium model. The maximum adsorption capacity at 25°C was 214.8 μg g(-1). The adsorption contribution decreased significantly when the Ce/Sw (the equilibrium concentration/solubility in water) was higher than 1. Adsorption decreased with increased temperature. Based on the above results, the corncob particles could be helpful in the bioremediation of pyrene-contaminated soil.

  12. Predicting Boron, Molybdenum, Selenium, and Arsenic Adsorption in Soil Systems

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A chemical surface complexation model was applied to boron, molybdenum, selenium, and arsenic adsorption on up to 49 soils selected for variation in soil properties. The surface complexation model was able to fit boron, molybdenum, selenite, and arsenate adsorption on the soils. General regression...

  13. Mechanism of amitriptyline adsorption on Ca-montmorillonite (SAz-2).

    PubMed

    Chang, Po-Hsiang; Jiang, Wei-Teh; Li, Zhaohui; Kuo, Chung-Yih; Jean, Jiin-Shuh; Chen, Wan-Ru; Lv, Guocheng

    2014-07-30

    The uptake of amitriptyline (AMI) from aqueous environment by Ca-montmorillonite (SAz-2) was studied in a batch system under different physicochemical conditions. The adsorbent was characterized by X-ray diffraction and Fourier transform infrared (FTIR) analyses. The AMI adsorption on SAz-2 obeyed the Langmuir isotherm with a capacity of 330mg/g (1.05mmol/g) at pH 6-7. The adsorption kinetics was fast, almost reaching equilibrium in 2h, and followed a pseudo-second-order kinetic model. Desorption of exchangeable cations correlated with the AMI adsorption well, indicating that cation exchange was the major mechanism. X-ray diffraction patterns showing significant expansions of the d001 spacing and characteristic FTIR band shifts toward higher frequencies after AMI adsorption onto SAz-2 indicated that the adsorbed AMI molecules were intercalated into the interlayers of the mineral. Thermodynamic parameters based on partitioning coefficients suggested that the AMI adsorption was an endothermic physisorption at high adsorption levels. At low and higher AMI adsorption levels, the intercalated AMI molecules take a horizontal monolayer and bilayer conformation, respectively. The higher adsorption capacity suggested that SAz-2 could be a good candidate to remove AMI from wastewater and would be an important environmental sink for the fate and transport of AMI in soils and groundwater.

  14. Adsorptive removal of PPCPs by biomorphic HAP templated from cotton.

    PubMed

    Huang, Bin; Xiong, Dan; Zhao, Tingting; He, Huan; Pan, Xuejun

    2016-01-01

    Biomorphic nano-hydroxyapatite (HAP) was fabricated by a co-precipitation method using cotton as bio-templates and employed in adsorptive removal of ofloxacin (OFL) and triclosan (TCS) that are two representative pharmaceuticals and personal care products (PPCPs). The surface area and porosity, crystal phase, functional group, morphology and micro-structure of the synthesized HAP were characterized by Brunauer-Emmett-Teller isotherm, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron macroscopic and transmission electron microscopy. The effects of initial pH, ionic strength, initial concentration, contact time and temperature on the removal of PPCPs were studied in a batch experiment. The adsorption of OFL and TCS was rapid and almost accomplished within 50 min. Kinetic studies indicated that the adsorption process of OFL and TCS followed the pseudo-first-order and pseudo-second-order models, respectively. The Freundlich isotherm described the OFL adsorption process well but the adsorption of TCS fitted the Langmuir isotherm better. Thermodynamics and isotherm parameters suggested that both OFL and TCS adsorption were feasible and spontaneous. Hydrogen bond and Lewis acid-base reaction may be the dominating adsorption mechanism of OFL and TCS, respectively. Compared to other adsorbents, biomorphic HAP is environmentally friendly and has the advantages of high adsorption capacity, exhibiting potential application for PPCPs removal.

  15. Arsenate Adsorption On Ruthenium Oxides: A Spectroscopic And Kinetic Investigation

    EPA Science Inventory

    Arsenate adsorption on amorphous (RuO2•1.1H2O) and crystalline (RuO2) ruthenium oxides was evaluated using spectroscopic and kinetic methods to elucidate the adsorption mechanism. Extended X-ray absorption fine structure spectroscopy (EXAFS) was ...

  16. EFFECT OF GAC CHARACTERISTICS ON ADSORPTION OF ORGANIC POLLUTANTS

    EPA Science Inventory

    The impact of the characteristics of granular activated carbon (GAC) on adsorption capacity and on the potential for polymerization of phenolic compounds on the surface of GAC in the presence of molecular oxygen is evaluated in this study. Adsorption isotherm data were collected...

  17. Antimony(V) Adsorption by Variable-Charge Minerals

    DTIC Science & Technology

    2013-10-01

    Sb(OH)6, SO4, and PO4 adsorption by gibbsite , kaolinite , goethite, and birnessite...pKa triple layer surface complexation modeling of Sb(OH)6, SO4, and PO4 adsorption by gibbsite , kaolinite , goethite, and birnessite...Competition Surface Complexation Triple Layer Model Gibbsite Kaolinite Goethite Birnessite xviii Abstract Background. Antimony (Sb) is a

  18. Adsorption and desorption characteristics of arsenic onto ceria nanoparticles

    NASA Astrophysics Data System (ADS)

    Feng, Qinzhong; Zhang, Zhiyong; Ma, Yuhui; He, Xiao; Zhao, Yuliang; Chai, Zhifang

    2012-01-01

    The rapid increase in the use of engineered nanoparticles [ENPs] has resulted in an increasing concern over the potential impacts of ENPs on the environmental and human health. ENPs tend to adsorb a large variety of toxic chemicals when they are emitted into the environment, which may enhance the toxicity of ENPs and/or adsorbed chemicals. The study was aimed to investigate the adsorption and desorption behaviors of arsenic on ceria NPs in aqueous solution using batch technique. Results show that the adsorption behavior of arsenic on ceria NPs was strongly dependent on pH and independent of ionic strength, indicating that the electrostatic effect on the adsorption of these elements was relatively not important compared to surface chemical reactions. The adsorption isotherms fitted very well to both the Langmuir and Freundlich models. The thermodynamic parameters (Δ H 0 , Δ S 0 , and Δ G 0 ) for the adsorption of arsenic were determined at three different temperatures of 283, 303, and 323 K. The adsorption reaction was endothermic, and the process of adsorption was favored at high temperature. The desorption data showed that desorption hysteresis occurred at the initial concentration studied. High adsorption capacity of arsenic on ceria NPs suggests that the synergistic effects of ceria NPs and arsenic on the environmental systems may exist when they are released into the environment.

  19. Adsorption behavior of some radionuclides on the Chinese weathered coal.

    PubMed

    Wu, Jianfeng; Xu, Qichu; Bai, Tao

    2007-08-01

    The equilibrium and kinetic properties of Am(III), Eu(III) and Cs(I) ions adsorption by three weathered coals (WCs) from China, have been investigated in batch stirred-tank experiments. The effects of contact time, solution acidity and initial sorbate concentration on the adsorption of Am(III), Eu(III) and Cs(I) by Yuxian(YX) Tongchuan (TC) and Pingxiang (PX) WC were evaluated. The radionuclide ions are able to form complex compounds with carboxylic and phenolic groups of WCs and they are also bounded with phenolic groups even at high acidity reaction solution (>0.1 mol/L). Mechanisms including ion exchange, complexation and adsorption to the coal surface are possible in the sorption process. The acidity of the solution played an important role in the adsorption. Even acidity as high as 0.1 mol/L, 60% of Am(III) or Eu(III), 40% of Cs(I) were found to be sorbed on the YX WC, which had the best adsorption capacity for Am(III) and Eu(III). Our batch adsorption studies showed the equilibrium adsorption data fit the linear Langmuir and Freundlich adsorption isotherm. The maximum equilibrium uptake of Eu(III) were 0.412, 3.701, 5.446 mmol/g for JXWC, TCWC and YXWC, respectively.

  20. Adsorption of soluble oil from water to graphene.

    PubMed

    Wang, Na; Zhang, Yuchang; Zhu, Fuzhen; Li, Jingyi; Liu, Shuaishuai; Na, Ping

    2014-05-01

    The toxicity of soluble oil to the aquatic environment has started to attract wide attention in recent years. In the present work, we prepare graphene according to oxidation and thermal reduction methods for the removal of soluble oil from the solution. Characterization of the as-prepared graphene are performed by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Raman spectra, Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy, and contact angle analysis. The adsorption behavior of soluble oil on graphene is examined, and the obtained adsorption data are modeled using conventional theoretical models. Adsorption experiments reveal that the adsorption rate of soluble oil on graphene is notably fast, especially for the soluble diesel oil, which could reach equilibrium within 30 min, and the kinetics of adsorption is perfectly consistent with a pseudo-second-order model. Furthermore, it is determined that the adsorption isotherm of soluble diesel oil with graphene fit the Freundlich model best, and graphene has a very strong adsorption capacity for soluble diesel oil in the solution. These results demonstrate that graphene is the material that provided both good adsorptive capacity and good kinetics, implying that it could be used as a promising sorbent for soluble oil removal from wastewater.

  1. Adsorption of mercury from water by modified multi-walled carbon nanotubes: adsorption behaviour and interference resistance by coexisting anions.

    PubMed

    Chen, Paris Honglay; Hsu, Cheng-Feng; Tsai, David Dah-wei; Lu, Yen-Ming; Huang, Winn-Jung

    2014-08-01

    This investigation reports the use of modified multi-walled carbon nanotubes (MWCNTs) with various functional groups for adsorbing inorganic divalent mercury (Hg(II)) from water samples. To elucidate the behaviours and mechanisms of Hg(II) adsorption by modified MWCNTs, their adsorption capacity was studied by considering adsorption isotherms and kinetics. Particular attention was paid to interference of coexisting inorganic ions with Hg(II) adsorption. The results reveal that functionalization with oxygen-containing groups improved the Hg(II) adsorption capacity of the MWCNTs. Kinetic analysis demonstrated that the adsorption of Hg(II) by MWCNTs was closely described by the pseudo-second-order and Elovich models, suggesting that the adsorption of Hg(II) by MWCNTs was significantly affected by chemical adsorption. The kinetic results were also analysed using the intraparticle diffusion model, which revealed that intraparticle diffusion was not the only rate-controlling mechanism. The adsorption of Hg(II) on MWCNTs fell drastically as the ionic strength increased from 0 to 1.0mol/L chloride ions, and declined significantly as the pH increased from 2.2 to 10.5. The elemental maps obtained by energy-dispersive spectrometer (EDS) revealed the formation of surface complexes of chloride ions with functional groups on MWCNTs, which reduced the number of available sites for the adsorption of Hg(II) and strengthened the repulsive forces between Hg(II) and MWCNTs. The EDS results suggest that chloride ions are important in controlling Hg(II) speciation and adsorption on the surfaces of MWCNTs.

  2. Kinetic and isotherm modeling of Cd (II) adsorption by L-cysteine functionalized multi-walled carbon nanotubes as adsorbent.

    PubMed

    Taghavi, Mahmoud; Zazouli, Mohammad Ali; Yousefi, Zabihollah; Akbari-adergani, Behrouz

    2015-11-01

    In this study, multi-walled carbon nanotubes were functionalized by L-cysteine to show the kinetic and isotherm modeling of Cd (II) ions onto L-cysteine functionalized multi-walled carbon nanotubes. The adsorption behavior of Cd (II) ion was studied by varying parameters including dose of L-MWCNTs, contact time, and cadmium concentration. Equilibrium adsorption isotherms and kinetics were also investigated based on Cd (II) adsorption tests. The results showed that an increase in contact time and adsorbent dosage resulted in increase of the adsorption rate. The optimum condition of the Cd (II) removal process was found at pH=7.0, 15 mg/L L-MWCNTs dosage, 6 mg/L cadmium concentration, and contact time of 60 min. The removal percent was equal to 89.56 at optimum condition. Langmuir and Freundlich models were employed to analyze the experimental data. The data showed well fitting with the Langmuir model (R2=0.994) with q max of 43.47 mg/g. Analyzing the kinetic data by the pseudo-first-order and pseudo-second-order equations revealed that the adsorption of cadmium using L-MWSNTs following the pseudo-second-order kinetic model with correlation coefficients (R2) equals to 0.998, 0.992, and 0.998 for 3, 6, and 9 mg/L Cd (II) concentrations, respectively. The experimental data fitted very well with the pseudo-second-order. Overall, treatment of polluted solution to Cd (II) by adsorption process using L-MWCNT can be considered as an effective technology.

  3. Adsorptive kinetic mechanism of heavy metal cations on the surface of graphite oxide and its SiO2 composite

    NASA Astrophysics Data System (ADS)

    Sheet, Imtithal; Kabbani, Ahmad; Holail, Hanafy

    2017-02-01

    Nanomaterials have gained great attention because of their novel size- and shape-dependent properties, large specific surface area and high reaction activity. Moreover, nanomaterials have a wide range of applications, as in the technological and environmental challenges in the areas of solar energy conversion, catalysis, medicine, and water treatments. In the present study, nanostructured graphite oxide, silica/graphite oxide composites and silica nanoparticles were used for the removal of the heavy metal ions from aqueous solutions by a batch adsorption method and the adsorptive kinetic mechanism of heavy metal cations on the surface of graphite oxide and its SiO2 composite was evaluated. The experimental results revealed a strong adsorption of the metal cations on the surface of graphite oxide, this is reflected in the shifts in wave numbers after adsorption with nanostructured graphite oxide and the big shift in wave numbers (Δv¯) for nickel ions reflects chemosorption type of adsorption. This is confirmed by the coherence between Δv¯, removal percentage and crystal field stabilization energy (CFSE). Silica/ GO (2:3) composite showed the greatest removal percentage at different concentrations compared to pure graphite oxide and silica nanoparticles. The higher removal percentage of nickel ions by silica /GO composite (2:3) was observed at 180 min contact time and basic pH. The kinetic studies showed that silica/ GO (2:3) composite had rapid adsorption rate and efficiency and it was found to follow first order rate expression or an exponential decay of the metal cations from water study.

  4. Lignin: A sustainable biosorbent for heavy metal adsorption from wastewater, a review

    NASA Astrophysics Data System (ADS)

    Nasrullah, Asma; Bhat, A. H.; Isa, Mohamed Hasnain

    2016-11-01

    With the recent advancements in science and technology, environmental pollution is a challenging problem due to increased activities in domestic, industrial, and agricultural sector. These activities have led to the release of various types of micropollutants such as heavy metal ions, organic and inorganic ions (detergents, and dye) etc into ground water which badly affects the ecosystem. Among various types of pollutants, heavy metals are the most reported in the recent decade. Water pollution is the most challenging problem, and needs to be controlled for better and healthy ecosystem which requires a healthy, eco-friendly and cheaper technology. In this context. lignin is abundantly available, cheaper and environmentally friendly. For efficient removal of heavy metals, lignin can be modified chemically or thermally to increased its biosorption capacity. In this review merits of adsorption and demerits of other separation technologies are compared. This paper presents the recent state of research on the efficient utilization of lignin, its modification and its adsorption efficiency for heavy metal removal from wastewater.

  5. Simulation and Optimization of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    NASA Technical Reports Server (NTRS)

    Swickrath, Michael J.; Anderson, Molly; McMillin, Summer; Broerman, Craig

    2010-01-01

    Controlling carbon dioxide (CO2) and humidity levels in a spacesuit is critical to ensuring both the safety and comfort of an astronaut during extra-vehicular activity (EVA). Traditionally, this has been accomplished utilizing non-regenerative lithium hydroxide (LiOH) or regenerative metal oxide (MetOx) canisters which pose a significant weight burden. Although such technology enables air revitalization, the volume requirements to store the waste canisters as well as the mass to transport multiple units become prohibitive as mission durations increase. Consequently, motivation exists toward developing a fully regenerative technology for environmental control. The application of solid amine materials with vacuum swing adsorption technology has shown the capacity to control CO2 and concomitantly manage humidity levels through a fully regenerative cycle eliminating mission constraints imposed with non-regenerative technologies. Experimental results for full-size and sub-scale test articles have been collected and are described herein. In order to accelerate the developmental efforts, an axially-dispersed plug ow model with an accompanying energy balance has been established and correlated with the experimental data. The experimental and simulation results display good agreement for a variety of ow rates (110-170 SLM), replicated metabolic challenges (100-590 Watts), and atmosphere pressures under consideration for the spacesuit (248 and 760 mm Hg). The relationship between swing adsorption cycles for an outlet criterion of 6.0 mm Hg of CO2 partial pressure has been established for each metabolic challenge. In addition, variable metabolic profiles were imposed on the test articles in order to assess the ability of the technology to transition to new operational constraints. The advent of the model provides the capacity to apply computer-aided engineering practices to support the ongoing efforts to optimize and mature this technology for future application to space

  6. Application of Vacuum Swing Adsorption for Carbon Dioxide and Water Vapor Removal from Manned Spacecraft Atmospheres

    NASA Technical Reports Server (NTRS)

    Knox, J.; Fulda, P.; Howard, D.; Ritter, J.; Levan, M.

    2007-01-01

    The design and testing of a vacuum-swing adsorption process to remove metabolic 'water and carbon dioxide gases from NASA's Orion crew exploration vehicle atmosphere is presented. For the Orion spacecraft, the sorbent-based atmosphere revitalization (SBAR) system must remove all metabolic water, a technology approach 1Lhathas not been used in previous spacecraft life support systems. Design and testing of a prototype SBAR in sub-scale and full-scale configurations is discussed. Experimental and analytical investigations of dual-ended and single-ended vacuum desorption are presented. An experimental investigation of thermal linking between adsorbing and desorbing columns is also presented.

  7. Porous cellulose spheres: Preparation, modification and adsorption properties.

    PubMed

    Ma, Xiaofei; Liu, Congzhi; Anderson, Debbie P; Chang, Peter R

    2016-12-01

    Porous cellulose spheres (PCS) were fabricated by precipitating the spheres from a cellulose ionic liquid solution, followed by freezing, solvent exchange, and drying. PCS had low crystallinity and a large surface area that facilitated modification with trisodium trimetaphosphate (STMP) to introduce phosphate ester groups into the porous structure of the heterogeneous system. The STMP-modified PCS (SPCS) were used to remove heavy metal ions from aqueous solution. With increasing STMP dosage, the adsorption capacity of SPCS obviously improved due to chelation between Pb(2+) and phosphate ester groups. The kinetic adsorption and isotherm data matched the pseudo-second order model and the Langmuir model well. The maximum adsorption capacity reached 150.6 mg g(-1) for SPCS. SPCS were competitive with other absorbents because the phosphate ester groups and porous structure contributed to Pb(2+) adsorption. Moreover, SPCS can be regenerated with ethylenediamine tetraacetic acid disodium salt (EDTA) solution for repetitious adsorption of Pb(2+).

  8. Adsorption of methylene blue from aqueous solution by graphene.

    PubMed

    Liu, Tonghao; Li, Yanhui; Du, Qiuju; Sun, Jiankun; Jiao, Yuqin; Yang, Guangming; Wang, Zonghua; Xia, Yanzhi; Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai

    2012-02-01

    Graphene was prepared using a modified Hummers' method. The physico-chemical properties of graphene were characterized by TEM, BET specific surface area, FTIR, Raman and XRD measurements. The effect factors including pH, contact time, temperature and dosage on the adsorption properties of methylene blue onto graphene were investigated. The experimental data of isotherm followed the Langmuir isotherm model better than the Freundlich model. The maximum adsorption capacity obtained from Langmuir isotherm equation at 293 K was 153.85 mg/g, indicating graphene is a good adsorbent for the adsorption of MB. The kinetic study illustrated that the adsorption of methylene blue onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of methylene blue onto graphene was an endothermic and spontaneous process.

  9. Study of Methylene Blue adsorption on keratin nanofibrous membranes.

    PubMed

    Aluigi, A; Rombaldoni, F; Tonetti, C; Jannoke, L

    2014-03-15

    In this work, keratin nanofibrous membranes (mean diameter of about 220nm) were prepared by electrospinning and tested as adsorbents for Methylene Blue through batch adsorption tests. The adsorption capacity of the membranes was evaluated as a function of initial dye concentration, pH, adsorbent dosage, time and temperature. The adsorption capacity increased with increasing the initial dye concentration and pH, while it decreased with increasing the adsorbent dosage and temperature, indicating an exothermic process. The adsorption results indicated that the Langmuir isotherm fitted the experimental data better than the Freundlich and Temkin isotherm models. A mean free energy evaluated through the Dubinin-Radushkevich model of about 16kJmol(-1), indicated a chemisorption process which occurred by ion exchange. The kinetic data were found to fit the pseudo-second-order model better than the pseudo-first-order model. The obtained results suggest that keratin nanofibrous membranes could be promising candidates as dye adsorption filters.

  10. Adsorption of trihalomethanes from water with carbon nanotubes.

    PubMed

    Lu, Chungsying; Chung, Yao-Lei; Chang, Kuan-Foo

    2005-03-01

    Commercial carbon nanotubes (CNTs) were purified by acid solution and were employed as adsorbents to study adsorption of trihalomethanes (THMs) from water. The properties of CNTs such as purity, structure and nature of the surface were greatly improved after acid treatment which made CNTs become more hydrophilic and suitable for adsorption of low molecular weight and relatively polar THM molecules. The adsorption of THMs onto CNTs fluctuates very little in the pH range 3-7, but decreases with pH value as pH exceeds 7. A comparative study between CNTs and powdered activated carbon (PAC) for adsorption of THMs from water was also conducted. The short time needed to reach equilibrium as well as the high adsorption capacity of CHCl3, which accounts for a significant portion of THMs in the chlorinated drinking water, suggests that CNTs possess highly potential applications for THMs removal from water.

  11. Adsorption of humic acids and trace metals in natural waters

    NASA Technical Reports Server (NTRS)

    Leung, W. H.

    1982-01-01

    Studies concerning the interactions between suspended hydrous iron oxide and dissolved humic acids and trace metals are reported. As a major component of dissolved organic matters and its readiness for adsorption at the solid/water interface, humic acids may play a very important role in the organometallic geochemistry of suspended sediments and in determining the fate and distribution of trace metals, pesticides and anions in natural water systems. Most of the solid phases in natural waters contain oxides and hydroxides. The most simple promising theory to describe the interactions of hydrous iron oxide interface is the surface complex formation model. In this model, the adsorptions of humic acids on hydrous iron oxide may be interpreted as complex formation of the organic bases (humic acid oxyanions) with surface Fe ions. Measurements on adsorptions were made in both fresh water and seawater. Attempts have been made to fit our data to Langmuir adsorption isotherm. Adsorption equilibrium constants were determined.

  12. High capacity adsorption media and method of producing

    DOEpatents

    Tranter, Troy J.; Herbst, R. Scott; Mann, Nicholas R.; Todd, Terry A.

    2008-05-06

    A method of producing an adsorption medium to remove at least one constituent from a feed stream. The method comprises dissolving at least one metal compound in a solvent to form a metal solution, dissolving polyacrylonitrile into the metal solution to form a PAN-metal solution, and depositing the PAN-metal solution into a quenching bath to produce the adsorption medium. The at least one constituent, such as arsenic, selenium, or antimony, is removed from the feed stream by passing the feed stream through the adsorption medium. An adsorption medium having an increased metal loading and increased capacity for arresting the at least one constituent to be removed is also disclosed. The adsorption medium includes a polyacrylonitrile matrix and at least one metal hydroxide incorporated into the polyacrylonitrile matrix.

  13. High capacity adsorption media and method of producing

    DOEpatents

    Tranter, Troy J.; Mann, Nicholas R.; Todd, Terry A.; Herbst, Ronald S.

    2010-10-05

    A method of producing an adsorption medium to remove at least one constituent from a feed stream. The method comprises dissolving and/or suspending at least one metal compound in a solvent to form a metal solution, dissolving polyacrylonitrile into the metal solution to form a PAN-metal solution, and depositing the PAN-metal solution into a quenching bath to produce the adsorption medium. The at least one constituent, such as arsenic, selenium, or antimony, is removed from the feed stream by passing the feed stream through the adsorption medium. An adsorption medium having an increased metal loading and increased capacity for arresting the at least one constituent to be removed is also disclosed. The adsorption medium includes a polyacrylonitrile matrix and at least one metal hydroxide incorporated into the polyacrylonitrile matrix.

  14. Competitive Protein Adsorption on Polysaccharide and Hyaluronate Modified Surfaces

    PubMed Central

    Ombelli, Michela; Costello, Lauren; Postle, Corinne; Anantharaman, Vinod; Meng, Qing Cheng; Composto, Russell J.; Eckmann, David M.

    2011-01-01

    We measured adsorption of bovine serum albumin (BSA) and fibrinogen (Fg) onto six distinct bare and dextran- and hyaluronate-modified silicon surfaces created using two dextran grafting densities and three hyaluronic acid (HA) sodium salts derived from human umbilical cord, rooster comb and streptococcus zooepidemicus. Film thickness and surface morphology depended on HA molecular weight and concentration. BSA coverage was enhanced on surfaces upon competitive adsorption of BSA:Fg mixtures. Dextranization differentially reduced protein adsorption onto surfaces based on oxidation state. Hyaluronization was demonstrated to provide the greatest resistance to protein coverage, equivalent to that of the most resistant dextranized surface. Resistance to protein adsorption was independent of the type of hyaluronic acid utilized. With changing bulk protein concentration from 20 to 40 µg ml−1 for each species, Fg coverage on silicon increased by 4×, whereas both BSA and Fg adsorption on dextran and HA were far less dependent of protein bulk concentration. PMID:21623481

  15. Hydrogen-graphite interaction: Experimental evidences of an adsorption barrier

    NASA Astrophysics Data System (ADS)

    Aréou, E.; Cartry, G.; Layet, J.-M.; Angot, T.

    2011-01-01

    The interaction of H atoms having relatively low average kinetic energy (˜0.025 eV) with both perfectly clean and D-covered HOPG surfaces is investigated using high resolution electron energy loss spectroscopy. From this study we confirm, in a controlled fashion, the presence of the theoretically predicted adsorption barrier since no adsorption is detected for such H atoms on HOPG. Moreover, we demonstrate that the exposure of a D saturated HOPG surface to these H atoms results in the complete removal of adatoms, with no further adsorption despite the prediction of the adsorption barrier to vanish for H dimers in para configuration. Therefore, the recombinative abstraction mechanism which competes with the adsorption process is more efficient.

  16. Methane Adsorption on Graphitic Nanostructures: Every Molecule Counts

    PubMed Central

    2012-01-01

    Bundles of single-walled nanotubes are promising candidates for storage of hydrogen, methane, and other hydrogen-rich molecules, but experiments are hindered by nonuniformity of the tubes. We overcome the problem by investigating methane adsorption on aggregates of fullerenes containing up to six C60; the systems feature adsorption sites similar to those of nanotube bundles. Four different types of adsorption sites are distinguished, namely, registered sites above the carbon hexagons and pentagons, groove sites between adjacent fullerenes, dimple sites between three adjacent fullerenes, and exterior sites. The nature and adsorption energies of the sites in C60 aggregates are determined by density functional theory and molecular dynamics (MD) simulations. Excellent agreement between experiment and theory is obtained for the adsorption capacity in these sites. PMID:23378887

  17. Reuse of Solid Waste in Adsorption of the Textile Dye

    NASA Astrophysics Data System (ADS)

    Meziti, Chafika; Boukerroui, Abdelhamid

    This work presents the study of the reuse of a regenerated spent bleaching earth (RSBE). The RSBE material was tested in the removal of a basic textile dye presents in aqueous solution. The effect of physicochemical parameters such as stirring speed, initial concentration, contact time and temperature have been invested and thermodynamic nature of the adsorption process was determined by calculating the ΔH°, ΔS° and ΔG° values The results obtained show that the adsorption mechanism was described by the Langmuir model and the adsorption capacity, qmax (72.41 to 82.37 mg.g-1), increases with temperature (20-50 °C). The thermodynamic parameters show a presence of a strong affinity between two phases (liquid-solid) and an endothermic equilibrium adsorption process. However, the phenomenon of the adsorption kinetic follows the pseudo second order kinetic model.

  18. Adsorption of organic phenols onto hexadecyltrimethylammonium-treated montmorillonite

    SciTech Connect

    Kim, Young S.; Song, Dong I.; Jeon, Young W.; Choi, Sang J.

    1996-12-01

    Montmorillonite used as an adsorbent was organically modified by using a cationic surfactant, hexadecyltrimethylammonium (HDTMA), to enhance the removal capacity of organic phenol contaminants dissolved in an aqueous solution. This modification produces a change of the surface property of montmorillonite from hydrophilic to organophilic. The single- and multicomponent competitive adsorptions were performed in a batch reactor to investigate the removal of three toxic organic phenols, 2-chlorophenol, 3-cyanophenol, and 4-nitrophenol, on the modified HDTMA-montmorillonite. It was observed from the experimental results that the adsorption affinity for HDTMA-montmorillonite was 2-chlorophenol, 4-nitrophenol, 3-cyanophenol in decreasing order. Langmuir and the Redlich-Peterson models were used to analyze the single-component adsorption results, while the IAST and the LCM models predicted the multicomponent adsorption equilibria. These models yielded favorable representations of both individual and competitive adsorption behaviors.

  19. Adsorption of trichlorophenol on zeolite and adsorbent regeneration with ozone.

    PubMed

    Zhang, Yongjun; Mancke, Raoul Georg; Sabelfeld, Marina; Geißen, Sven-Uwe

    2014-04-30

    A FAU-type zeolite was studied as an adsorbent to remove 2,4,6-trichlorophenol (TCP), a frequently detected recalcitrant pollutant in water bodies. Both adsorption isotherm and kinetics were studied with TCP concentrations from 10 to 100mg/L. It was observed that TCP was effectively adsorbed onto the zeolite with a high adsorption capacity and a high kinetic rate. Freundlich model and pseudo-second-order kinetics were successfully applied to describe the experimental data. The influence of solution pH was also studied. Furthermore, ozone was applied to regenerate the loaded zeolite. It was found that an effective adsorption of TCP was kept for at least 8 cycles of adsorption and regeneration. The ozonation also increased the BET specific surface of zeolite by over 60% and consequently enhanced the adsorption capacity.

  20. Natural Minerals Coated by Biopolymer Chitosan: Synthesis, Physicochemical, and Adsorption Properties.

    PubMed

    Budnyak, T M; Yanovska, E S; Kichkiruk, O Yu; Sternik, D; Tertykh, V A

    2016-12-01

    Natural minerals are widely used in treatment technologies as mineral fertilizer, food additive in animal husbandry, and cosmetics because they combine valuable ion-exchanging and adsorption properties together with unique physicochemical and medical properties. Saponite (saponite clay) of the Ukrainian Podillya refers to the class of bentonites, a subclass of layered magnesium silicate montmorillonite. Clinoptilolits are aluminosilicates with carcase structure. In our work, we have coated biopolymer chitosan on the surfaces of natural minerals of Ukrainian origin - Podilsky saponite and Sokyrnitsky clinoptilolite. Chitosan mineral composites have been obtained by crosslinking of adsorbed biopolymer on saponite and clinoptilolite surface with glutaraldehyde. The obtained composites have been characterized by the physicochemical methods such as thermogravimetric/differential thermal analyses (DTA, DTG, TG), differential scanning calorimetry, mass analysis, nitrogen adsorption/desorption isotherms, scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy to determine possible interactions between the silica and chitosan molecule. The adsorption of microquantities of cations Cu(II), Zn(II), Fe(III), Cd(II), and Pb(II) by the obtained composites and the initial natural minerals has been studied from aqueous solutions. The sorption capacities and kinetic adsorption characteristics of the adsorbents were estimated. It was found that the obtained results have shown that the ability of chitosan to coordinate heavy metal ions Zn(II), Cu(II), Cd(II), and Fe(III) is less or equal to the ability to retain ions of these metals in the pores of minerals without forming chemical bonds.

  1. Tailoring the protein adsorption properties of whispering gallery mode optical biosensors.

    PubMed

    Soteropulos, Carol E; Zurick, Kevin M; Bernards, Matthew T; Hunt, Heather K

    2012-11-06

    Label-free biosensor technologies have the potential to revolutionize environmental monitoring, medical diagnostics, and food safety evaluation processes due to their unique combinations of high-sensitivity signal transducers and high-specificity recognition elements. This enables their ability to perform real-time detection of deleterious compounds at extremely low concentrations. However, to further improve the biosensors' performance in complex environments, such as wastewater, blood, and urine, it is necessary to minimize nonspecific binding, which in turn will increase their specificity, and decrease the rate of false positives. In the present work, we illustrate the potential of combining emerging high-sensitivity optical signal transducers, such as whispering gallery mode (WGM) microcavities, with covalently bound poly(ethylene glycol) (PEG) coatings of varying thickness, as an effective treatment for the prevention of nonspecific protein adsorption onto the biosensor surface. We monitor the sensitivity of the coated biosensor, and investigate the effect of PEG chain length on minimizing nonspecific adsorption via protein adsorption studies. Experimental results confirm not only that PEG-functionalization reduces nonspecific protein adsorption to the surface of the sensor by as much as a factor of 4 compared to an initialized control surface, but also that chain length significantly impacts the nonfouling character of the microcavity surface. Surprisingly, it is the short chain PEG surfaces that experience the best improvement in specificity, unlike many other systems where longer PEG chains are preferred. The combination of WGM microcavities with PEG coatings tuned specifically to the device will significantly improve the overall performance of biosensor platforms, and enable their wider application in complex, real-world monitoring scenarios.

  2. Adsorption characteristics of activated carbon fibers (ACFs) for toluene: application in respiratory protection.

    PubMed

    Balanay, Jo Anne G; Bartolucci, Alfred A; Lungu, Claudiu T

    2014-01-01

    Granular activated carbon (GAC) is currently the standard adsorbent in respirators against several gases and vapors because of its efficiency, low cost, and available technology. However, a drawback of GAC due to its granular form is its need for containment, adding weight and bulkiness to respirators. This makes respirators uncomfortable to wear, resulting in poor compliance in their use. Activated carbon fibers (ACF) are considered viable alternative adsorbent materials for developing thinner, light-weight, and efficient respirators because of their larger surface area, lighter weight, and fabric form. This study aims to determine the critical bed depth and adsorption capacity of different types of commercially available ACFs for toluene to understand how thin a respirator can be and the service life of the adsorbents, respectively. ACF in cloth (ACFC) and felt (ACFF) forms with three different surface areas per form were tested. Each ACF type was challenged with six concentrations of toluene (50, 100, 200, 300, 400, 500 ppm) at constant air temperature (23°C), relative humidity (50%), and airflow (16 LPM) at different adsorbent weights and bed depths. Breakthrough data were obtained for each adsorbent using gas chromatography with flame ionization detector. The ACFs' surface areas were measured by an automatic physisorption analyzer. The results showed that ACFC has a lower critical bed depth and higher adsorption capacity compared to ACFF with similar surface area for each toluene concentration. Among the ACF types, ACFC2000 (cloth with the highest measured surface area of 1614 ± 5 m(2)/g) has one of the lowest critical bed depths (ranging from 0.11-0.22 cm) and has the highest adsorption capacity (ranging from 595-878 mg/g). Based on these studied adsorption characteristics, it is concluded that ACF has great potential for application in respiratory protection against toluene, particularly the ACFC2000, which is the best candidate for developing thinner and

  3. Selective adsorption of flavor-active components on hydrophobic resins.

    PubMed

    Saffarionpour, Shima; Sevillano, David Mendez; Van der Wielen, Luuk A M; Noordman, T Reinoud; Brouwer, Eric; Ottens, Marcel

    2016-12-09

    This work aims to propose an optimum resin that can be used in industrial adsorption process for tuning flavor-active components or removal of ethanol for producing an alcohol-free beer. A procedure is reported for selective adsorption of volatile aroma components from water/ethanol mixtures on synthetic hydrophobic resins. High throughput 96-well microtiter-plates batch uptake experimentation is applied for screening resins for adsorption of esters (i.e. isoamyl acetate, and ethyl acetate), higher alcohols (i.e. isoamyl alcohol and isobutyl alcohol), a diketone (diacetyl) and ethanol. The miniaturized batch uptake method is adapted for adsorption of volatile components, and validated with column breakthrough analysis. The results of single-component adsorption tests on Sepabeads SP20-SS are expressed in single-component Langmuir, Freundlich, and Sips isotherm models and multi-component versions of Langmuir and Sips models are applied for expressing multi-component adsorption results obtained on several tested resins. The adsorption parameters are regressed and the selectivity over ethanol is calculated for each tested component and tested resin. Resin scores for four different scenarios of selective adsorption of esters, higher alcohols, diacetyl, and ethanol are obtained. The optimal resin for adsorption of esters is Sepabeads SP20-SS with resin score of 87% and for selective removal of higher alcohols, XAD16N, and XAD4 from Amberlite resin series are proposed with scores of 80 and 74% respectively. For adsorption of diacetyl, XAD16N and XAD4 resins with score of 86% are the optimum choice and Sepabeads SP2MGS and XAD761 resins showed the highest affinity towards ethanol.

  4. Advances in principal factors influencing carbon dioxide adsorption on zeolites

    PubMed Central

    Bonenfant, Danielle; Kharoune, Mourad; Niquette, Patrick; Mimeault, Murielle; Hausler, Robert

    2008-01-01

    We report the advances in the principal structural and experimental factors that might influence the carbon dioxide (CO2) adsorption on natural and synthetic zeolites. The CO2 adsorption is principally govern by the inclusion of exchangeable cations (countercations) within the cavities of zeolites, which induce basicity and an electric field, two key parameters for CO2 adsorption. More specifically, these two parameters vary with diverse factors including the nature, distribution and number of exchangeable cations. The structure of framework also determines CO2 adsorption on zeolites by influencing the basicity and electric field in their cavities. In fact, the basicity and electric field usually vary inversely with the Si/Al ratio. Furthermore, the CO2 adsorption might be limited by the size of pores within zeolites and by the carbonates formation during the CO2 chemisorption. The polarity of molecules adsorbed on zeolites represents a very important factor that influences their interaction with the electric field. The adsorbates that have the most great quadrupole moment such as the CO2, might interact strongly with the electric field of zeolites and this favors their adsorption. The pressure, temperature and presence of water seem to be the most important experimental conditions that influence the adsorption of CO2. The CO2 adsorption increases with the gas phase pressure and decreases with the rise of temperature. The presence of water significantly decreases adsorption capacity of cationic zeolites by decreasing strength and heterogeneity of the electric field and by favoring the formation of bicarbonates. The optimization of the zeolites structural characteristics and the experimental conditions might enhance substantially their CO2 adsorption capacity and thereby might give rise to the excellent adsorbents that may be used to capturing the industrial emissions of CO2. PMID:27877925

  5. The adsorption behavior of U(VI) on granite.

    PubMed

    Fan, Q H; Hao, L M; Wang, C L; Zheng, Z; Liu, C L; Wu, W S

    2014-03-01

    The effects of pH, counter ions and temperature on the adsorption of U(VI) on Beishan granite (BsG) were investigated in the presence and absence of fulvic acid (FA) and humic acid (HA). The adsorption edge of U(VI) on BsG suggested that U(VI) adsorption was mainly controlled by ion exchange and outer-sphere complexation at low pH, whereas inner-sphere complex was the dominant adsorption species in the pH range of 4.0-9.0. Above pH 9.0, Na2U2O7 might play an important role in the rise of U(VI) adsorption again. Counter ions such as Cl(-), SO4(2-) and PO4(3-) can provoke U(VI) adsorption on BsG to some extent, which was directly correlated to the complexing ability of U(VI)-ligand. More noticeably, the large enhancement of U(VI) adsorption in the presence of phosphate can be attributed to the ternary complex formation (BsG-PO4-UO2), precipitation ((UO2)3(PO4)2(s)) and secondary phase (Na-autunite). Both FA and HA can slightly increase U(VI) adsorption at low pH, whereas they strongly inhibited U(VI) adsorption at high pH range. Artificial synthesized granite (AsG) prepared in the laboratory is impossible to use as an analogue of natural granite because of the large difference in the adsorption and surface properties.

  6. Phase 2 Methyl Iodide Deep-Bed Adsorption Tests

    SciTech Connect

    Soelberg, Nick; Watson, Tony

    2014-09-01

    Nuclear fission produces fission products (FPs) and activation products, including iodine-129, which could evolve into used fuel reprocessing facility off-gas systems, and could require off-gas control to limit air emissions to levels within acceptable emission limits. Research, demonstrations, and some reprocessing plant experience have indicated that diatomic iodine can be captured with efficiencies high enough to meet regulatory requirements. Research on the capture of organic iodides has also been performed, but to a lesser extent. Several questions remain open regarding the capture of iodine bound in organic compounds. Deep-bed methyl iodide adsorption testing has progressed according to a multi-laboratory methyl iodide adsorption test plan. This report summarizes the second phase of methyl iodide adsorption work performed according to this test plan using the deep-bed iodine adsorption test system at the Idaho National Laboratory (INL), performed during the second half of Fiscal Year (FY) 2014. Test results continue to show that methyl iodide adsorption using AgZ can achieve total iodine decontamination factors (DFs, ratios of uncontrolled and controlled total iodine levels) above 1,000, until breakthrough occurred. However, mass transfer zone depths are deeper for methyl iodide adsorption compared to diatomic iodine (I2) adsorption. Methyl iodide DFs for the Ag Aerogel test adsorption efficiencies were less than 1,000, and the methyl iodide mass transfer zone depth exceeded 8 inches. Additional deep-bed testing and analyses are recommended to (a) expand the data base for methyl iodide adsorption under various conditions specified in the methyl iodide test plan, and (b) provide more data for evaluating organic iodide reactions and reaction byproducts for different potential adsorption conditions.

  7. Adsorption behavior of the catechins and caffeine onto polyvinylpolypyrrolidone.

    PubMed

    Dong, Zhan-Bo; Liang, Yue-Rong; Fan, Fang-Yuan; Ye, Jian-Hui; Zheng, Xin-Qiang; Lu, Jian-Liang

    2011-04-27

    Adsorbent is one of the most important factors for separation efficiency in fixed-bed purification techniques. The adsorption behavior of catechins and caffeine onto polyvinylpolypyrrolidone (PVPP) was investigated by static adsorption tests. The results showed that catechins rather than caffeine were preferred to adsorb onto PVPP since the adsorption selectivity coefficient of total catechins vs caffeine was around 22.5, and that adsorption of catechins could be described by the pseudo-second-order model. Adsorption amount of caffeine onto PVPP in green tea extracts solution was much higher than that in purified caffeine solution although the initial concentration of caffeine was similar in the two solutions, indicating the caffeine might be attached with catechins which were adsorbed by PVPP instead of being adsorbed by PVPP directly. The results also showed that the adsorption capacity of catechins and caffeine decreased with an increase in temperature, and that Freundlich and Langmuir models were both suitable for describing the isothermal adsorption of catechins, but not suitable for caffeine. The predicted maximum monolayer adsorption capacity of total catechins by PVPP was 671.77 mg g(-1) at 20 °C, which was significantly higher than that by other reported adsorbents. The thermodynamics analyses indicated that the adsorption of catechins onto PVPP was a spontaneous and exothermic physisorption process, revealing lower temperature was favorable for the adsorption of catechins. Elution tests showed that the desorption rates of catechins and caffeine were higher than 91% and 99% after two elution stages; in detail, almost all of the caffeine could be washed down at the water eluting stage, while catechins could be recovered at the dimethyl sulfoxide/ethanol solution eluting stage. Thus, the PVPP could be used as an excellent alternative adsorbent candidate for separating catechins from crude tea extracts, although some investigations, such as exploring the new

  8. Extension-Upgrading Methane Using Ultra-Fast Thermal Swing Adsorption

    SciTech Connect

    Anna Lee Tonkovich

    2006-04-01

    The purpose of this project is to develop a cost effective technology for upgrading coal mine methane to natural gas pipeline quality. Nitrogen rejection is the most costly step with conventional technology and emerging competitive technology. Significant cost reductions to this step will allow for the cost effective capture and utilization of this otherwise potent greenhouse gas. The proposed approach is based on the microchannel technology platform that Velocys is developing to commercialize compact and cost efficient chemical processing technology. For this application, ultra fast thermal swing adsorption is enabled by the very high rates of heat transfer enabled by microchannels. Natural gas upgrading systems have six main unit operations: feed compressor, dehydration unit, nitrogen rejection unit, deoxygenator, carbon dioxide scrubber, and a sales compressor. The NRU is the focus of the development program, and a bench-scale demonstration has been initiated. The Velocys NRU system targets producing methane with greater than 96% purity and at least 90% recovery for final commercial operation. A preliminary cost analysis of the methane upgrading system, including the Velocys NRU, suggests that costs below $2.00 per million (MM) BTU methane may be achieved. The cost for a conventional methane upgrading system is well above $2.30 per MM BTU, as benchmarked in an Environmental Protection Agency study. Initial performance results for the Velocys TSA technology were promising. Velocys has also completed initial discussions with several prospective users of the technology and received positive market feedback. Some of the factors that create an attractive opportunity for the technology include the sustained high prices for natural gas, the emerging system of carbon credits, and continued focus on reducing coal mine emissions. While market interest has been confirmed, improvements and optimization are necessary to move the technology to a point that will enable

  9. Arsenic Removal from Drinking Water by Adsorptive Media - U.S. EPA Demonstration Project at Seely-Brown Village in Pomfret, CT - Final Performance Evaluation Report

    EPA Science Inventory

    This report documents the activities performed for and the results obtained from the arsenic removal treatment technology demonstration project at Seely-Brown Village in Pomfret, CT. The objectives of the project were to evaluate the effectiveness of ArsenXnp adsorption media in...

  10. Arsenic Removal from Drinking Water by Adsorptive Media, U.S. EPA Demonstration Project at Lead, South Dakota - Final Performance Evaluation Report

    EPA Science Inventory

    This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project at Lead, South Dakota. The main objective of the project was to evaluate the effectiveness of SolmeteX’s adsorptive media system in removin...

  11. Arsenic Removal from Drinking Water by Adsorptive Media U.S. EPA Demonstration Project at Brown City, MI Final Performance Evaluation Report

    EPA Science Inventory

    This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project in Brown City, MI. The objectives of the project were to evaluate (1) the effectiveness of a Severn Trent Services (STS) adsorptive media s...

  12. Synthesis of Large-Pore Stabilized MIL-53(Al) Compounds with Increased CO2 Adsorption and Decreased Water Adsorption

    DTIC Science & Technology

    2014-01-01

    isotherms showed typical Type I behaviour as per the IUPAC classification. Gas adsorption An Intelligent Gravimetric Analyzer ( IGA -1 series, Hiden...40 min was used for each point in the isotherm. Water adsorption An Intelligent Gravimetric Analyzer ( IGA -3 series, Hiden Analytical Ltd.) was used

  13. Coupled Electrokinetics-Adsorption Technique for Simultaneous Removal of Heavy Metals and Organics from Saline-Sodic Soil

    PubMed Central

    Lukman, Salihu; Essa, Mohammed Hussain; Mu'azu, Nuhu Dalhat; Bukhari, Alaadin

    2013-01-01

    In situ remediation technologies for contaminated soils are faced with significant technical challenges when the contaminated soil has low permeability. Popular traditional technologies are rendered ineffective due to the difficulty encountered in accessing the contaminants as well as when employed in settings where the soil contains mixed contaminants such as petroleum hydrocarbons, heavy metals, and polar organics. In this study, an integrated in situ remediation technique that couples electrokinetics with adsorption, using locally produced granular activated carbon from date palm pits in the treatment zones that are installed directly to bracket the contaminated soils at bench-scale, is investigated. Natural saline-sodic soil, spiked with contaminant mixture (kerosene, phenol, Cr, Cd, Cu, Zn, Pb, and Hg), was used in this study to investigate the efficiency of contaminant removal. For the 21-day period of continuous electrokinetics-adsorption experimental run, efficiency for the removal of Zn, Pb, Cu, Cd, Cr, Hg, phenol, and kerosene was found to reach 26.8, 55.8, 41.0, 34.4, 75.9, 92.49, 100.0, and 49.8%, respectively. The results obtained suggest that integrating adsorption into electrokinetic technology is a promising solution for removal of contaminant mixture from saline-sodic soils. PMID:24235885

  14. Coupled electrokinetics-adsorption technique for simultaneous removal of heavy metals and organics from saline-sodic soil.

    PubMed

    Lukman, Salihu; Essa, Mohammed Hussain; Mu'azu, Nuhu Dalhat; Bukhari, Alaadin

    2013-01-01

    In situ remediation technologies for contaminated soils are faced with significant technical challenges when the contaminated soil has low permeability. Popular traditional technologies are rendered ineffective due to the difficulty encountered in accessing the contaminants as well as when employed in settings where the soil contains mixed contaminants such as petroleum hydrocarbons, heavy metals, and polar organics. In this study, an integrated in situ remediation technique that couples electrokinetics with adsorption, using locally produced granular activated carbon from date palm pits in the treatment zones that are installed directly to bracket the contaminated soils at bench-scale, is investigated. Natural saline-sodic soil, spiked with contaminant mixture (kerosene, phenol, Cr, Cd, Cu, Zn, Pb, and Hg), was used in this study to investigate the efficiency of contaminant removal. For the 21-day period of continuous electrokinetics-adsorption experimental run, efficiency for the removal of Zn, Pb, Cu, Cd, Cr, Hg, phenol, and kerosene was found to reach 26.8, 55.8, 41.0, 34.4, 75.9, 92.49, 100.0, and 49.8%, respectively. The results obtained suggest that integrating adsorption into electrokinetic technology is a promising solution for removal of contaminant mixture from saline-sodic soils.

  15. H Adsorption on RH (110) Surface

    NASA Astrophysics Data System (ADS)

    Chen, Shao-Ping

    2006-03-01

    We have used the density functional theory to study the H adsorption phenomena on Rh (110) surface with H coverage from 0.33 to 2.00 mono-layers. We found H atom favors the three- fold coordinated site as observed experimentally. We confirmed the existence of 1x3-H, 1x2-H, 1x3-2H, 1x1-2H ordered structures. We also found that the proposed 1x2-2H structure for coverage of 1.0 is not the lowest energy configuration. We have proposed a new 1x2-2H structure which needs to be tested by future experiments.

  16. A review of protein adsorption on bioceramics.

    PubMed

    Wang, Kefeng; Zhou, Changchun; Hong, Youliang; Zhang, Xingdong

    2012-06-06

    Bioceramics, because of its excellent biocompatible and mechanical properties, has always been considered as the most promising materials for hard tissue repair. It is well know that an appropriate cellular response to bioceramics surfaces is essential for tissue regeneration and integration. As the in vivo implants, the implanted bioceramics are immediately coated with proteins from blood and body fluids, and it is through this coated layer that cells sense and respond to foreign implants. Hence, the adsorption of proteins is critical within the sequence of biological activities. However, the biological mechanisms of the interactions of bioceramics and proteins are still not well understood. In this review, we will recapitulate the recent studies on the bioceramic-protein interactions.

  17. Modifying of gas adsorption on phosphorene

    NASA Astrophysics Data System (ADS)

    Salmankurt, Bahadır; Gürel, Hikmet Hakan

    2017-02-01

    After the discovery of Graphene, new two dimensional (2D) materials has been found out. Among them, Phosphorene, has a significant advantage over the semimetallic graphene and other typical 2D semiconductors. 2D materials are also usually good candidates for gas sensors thanks to their large surface-to-volume ratio and the associated charge transfer between gas molecules and the substrates. Theoretical efforts have been devoted to study the interactions of this 2D material with different molecules(CO, H2O, CH4 and NH3). But interactions of such molecules with blue phosphorene are lack. Thus, theoretical study based on Density Functional Theory (DFT) have been performed to investigate the molecules adsorption on phosphorene with Vander walls effect. It is also shown that how modify structural of the molecules on phosphorene by applied charging.

  18. Reactive spreading: Adsorption, ridging and compound formation

    SciTech Connect

    Saiz, E.; Cannon, R.M.; Tomsia, A.P.

    2000-09-11

    Reactive spreading, in which a chemically active element is added to promote wetting of noble metals on nonmetallic materials, is evaluated. Theories for the energetics and kinetics of the necessary steps involved in spreading are outlined and compared to the steps in compound formation that typically accompany reactive wetting. These include: fluid flow, active metal adsorption, including nonequilibrium effects, and triple line ridging. All of these can be faster than compound nucleation under certain conditions. Analysis and assessment of recently reported experiments on metal/ceramic systems lead to a focus on those conditions under which spreading proceeds ahead of the actual formation of a new phase at the interface. This scenario may be more typical than believed, and perhaps the most effective situation leading to enhanced spreading. A rationale for the pervasive variability and hysteresis observed during high temperature wetting also emerges.

  19. Random sequential adsorption on imprecise lattice

    NASA Astrophysics Data System (ADS)

    Privman, Vladimir; Yan, Han

    2016-06-01

    We report a surprising result, established by numerical simulations and analytical arguments for a one-dimensional lattice model of random sequential adsorption, that even an arbitrarily small imprecision in the lattice-site localization changes the convergence to jamming from fast, exponential, to slow, power-law, with, for some parameter values, a discontinuous jump in the jamming coverage value. This finding has implications for irreversible deposition on patterned substrates with pre-made landing sites for particle attachment. We also consider a general problem of the particle (depositing object) size not an exact multiple of the lattice spacing, and the lattice sites themselves imprecise, broadened into allowed-deposition intervals. Regions of exponential vs. power-law convergence to jamming are identified, and certain conclusions regarding the jamming coverage are argued for analytically and confirmed numerically.

  20. Adsorption of fulvic acid on goethite

    SciTech Connect

    Filius, J.D.; Lumsdon, D.G.; Meeussen, J.C.L.; Hiemstra, T.; Riemsduk, W.H. van

    2000-01-01

    The adsorption of fulvic acid by goethite was determined experimentally as a function of concentration, pH, and ionic strength. The data were described with the CD-MUSIC model of Hiemstra and Van Riemsdijk (1996), which allows the distribution of charge of the bound fulvate molecule over a surface region. Simultaneously, the concentration, pH, and salt dependency of the binding of fulvic acid can be described. Using the same parameters, the basic charging behavior of the goethite in the absence of fulvic acid could be described well. The surface species used in the model indicate that inner sphere coordination of carboxylic groups of the fulvate molecule is important at low pH, whereas at high pH the outer sphere coordination with reactive groups of the fulvate molecule with high proton affinity is important.

  1. Ammonia Process by Pressure Swing Adsorption

    SciTech Connect

    Dr Felix Jegede

    2010-12-27

    The overall objective of the project is to design, develop and demonstrate a technically feasible and commercially viable system to produce ammonia along with recovery of the products by adsorption separation methods and significantly decrease the energy requirement in ammonia production. This is achieved through a significantly more efficient ammonia psa recovery system. The new ammonia recovery system receives the reactor effluents and achieves complete ammonia recovery, (which completely eliminates the energy intensive refrigeration and condensation system currently used in ammonia production). It also recovers the unused reactants and recycles them back to the reactor, free of potential reactor contaminants, and without the need for re-compression and re-heat of recycle stream thereby further saving more energy. The result is a significantly lower energy consumption, along with capital cost savings.

  2. Basicity, Catalytic and Adsorptive Properties of Hydrotalcites

    NASA Astrophysics Data System (ADS)

    Figueras, Francois

    Solid bases have numerous potential applications, not only as catalyst for the manufacture of fine chemicals, in refining and petrochemistry, but also for adsorption and anion exchange. The present processes use liquid bases, typically alcoholic potash, and require neutralisation of the reaction medium at the end of the reaction, with production of salts. The substitution of these liquid bases by solids would provide cleaner and safer processes, due to the reduction of salts, and facilitate separation of the products and recycling of the catalyst. This chapter reviews the recent ideas on the modification of the basic properties of hydrotalcites by anion exchange and on the catalytic properties of solid bases as catalysts. Many examples of successful applications are given, with emphasis to industrial processes recently presented such as isomerisation of olefins. The basic properties of hydrotalcites can also be used to carry the exchange of toxic anions, humic acids or dyes, and have driven recent developments proposing HDT as drug carriers.

  3. Zn isotope fractionation during adsorption on birnessite

    NASA Astrophysics Data System (ADS)

    Bryan, A. L.; Dong, S.; Wasylenki, L. E.

    2013-12-01

    The biogeochemical cycling of zinc (Zn), an important micronutrient in the ocean, may influence primary productivity and species composition within surface waters. The chemical speciation and bioavailability of Zn is governed by diverse abiotic and biotic processes. These processes include adsorption reactions at mineral/water interfaces, as nanoparticles of oxyhydroxide minerals are known to adsorb significant amounts of Zn in surface waters (and during formation of ferromanganese crusts). Investigation of Zn isotope fractionation caused by adsorption onto birnessite, the dominant manganese oxide mineral in ferromanganese crusts, may help to explain the enrichment of heavy Zn isotopes in ferromanganese crusts. This will provide insight into the role of adsorption of Zn to nanoparticulate minerals in surface waters and into the overall biogeochemical cycling of Zn. This work aims to determine the mechanism and magnitude of Zn isotope fractionation during adsorption onto synthetic birnessite (KMn2O4.1.5H2O). Our simple-system experiments involve mixing solutions of 130 ppb Zn with aliquots of birnessite suspension (proportions varied to give a range of surface coverage) and a fixed pH near that of seawater at ~8.5. The mixtures react for 48 hours. The recovered dissolved Zn and adsorbed Zn are then separated, purified, and analyzed isotopically on a Nu Plasma MC-ICP-MS. Preliminary results show enrichment of light Zn isotopes on the mineral surfaces (Δ66/64Znsorbed-aqueous = -0.3‰). A time series will reveal whether this process is governed by equilibrium or Rayleigh fractionation. Contrary to our results, previously published studies led us to hypothesize that isotopically heavy Zn would adsorb compared to co-existing dissolved Zn. Maréchal et al. (2000) recorded ferromanganese crusts that were heavier than seawater with a mean δ66Zn value of 0.90‰. Dissolved Zn is octahedrally coordinated with oxygen atoms, but an EXAFS study by Manceau et al. (2002

  4. A review of protein adsorption on bioceramics

    PubMed Central

    Wang, Kefeng; Zhou, Changchun; Hong, Youliang; Zhang, Xingdong

    2012-01-01

    Bioceramics, because of its excellent biocompatible and mechanical properties, has always been considered as the most promising materials for hard tissue repair. It is well know that an appropriate cellular response to bioceramics surfaces is essential for tissue regeneration and integration. As the in vivo implants, the implanted bioceramics are immediately coated with proteins from blood and body fluids, and it is through this coated layer that cells sense and respond to foreign implants. Hence, the adsorption of proteins is critical within the sequence of biological activities. However, the biological mechanisms of the interactions of bioceramics and proteins are still not well understood. In this review, we will recapitulate the recent studies on the bioceramic–protein interactions. PMID:23741605

  5. The adsorption of plutonium IV and V on goethite

    NASA Astrophysics Data System (ADS)

    Sanchez, Arthur L.; Murray, James W.; Sibley, Thomas H.

    1985-11-01

    The adsorption of Pu(IV) and Pu(V) on goethite (αFeOOH) from NaNO 3 solution shows distinct differences related to the different hydrolytic character of these two oxidation states. Under similar solution conditions, the adsorption edge of the more strongly hydrolyzable Pu(IV) occurs in the pH range 3 to 5 while that for Pu(V) is at pH 5 to 7. The adsorption edge for Pu(V) shifts with time to lower pH values and this appears to be due to the reduction of Pu(V) to Pu(IV) in the presence of the goethite surface. These results suggest that redox transformations may be an important aspect of Pu adsorption chemistry and the resulting scavenging of Pu from natural waters. Increasing ionic strength (from 0.1 M to 3 M NaCl or NaNO 3 and 0.03 M to 0.3 M Na 2SO 4) did not influence Pu(IV) or Pu(V) adsorption. In the presence of dissolved organic carbon (DOC), Pu(V) reduction to Pu(IV) occurred in solution. Pu(IV) adsorption on goethite decreased by 30% in the presence of 240 ppm natural DOC found in Soap Lake, Washington waters. Increasing concentrations of carbonate ligands decreased Pu(IV) and Pu(V) adsorption on goethite, with an alkalinity of 1000 meq/l totally inhibiting adsorption. The Pu-goethite adsorption system provides the data base for developing a thermodynamic model of Pu interaction with an oxide surface and with dissolved ligands, using the MINEQL computer program. From the model calculations we determined equilibrium constants for the adsorption of Pu(IV) hydrolysis species. The model was then applied to Pu adsorption in carbonate media to see how the presence of CO 3-2 could influence the mobility of Pu. The decrease in adsorption appears to be due to formation of a Pu-CO 3 complex. Model calculations were used to predict what the adsorption curves would look like if Pu-CO 3 complexes formed.

  6. Simultaneous adsorption of phenol and cadmium on amphoteric modified soil.

    PubMed

    Meng, Zhao-Fu; Zhang, Yi-Ping; Zhang, Zeng-Qiang

    2008-11-30

    Surface modification is an effective way to enhance adsorption of pollutants by soil. In this study, we investigated the individual adsorption of cadmium ion (Cd(2+)) and phenol and also in combination by the clay layer of a loessial soil treated with the amphoteric modifier, duodalkylbetaine (BS-12). Three levels of BS-12 modification were compared in this experiment: (1) unmodified soil (CK), (2) modification with an amount of BS-12 equivalent to 50% of the soil's CEC (50BS) and (3) modification with an amount of BS-12 equivalent to 100% of the soil's CEC (100BS). Cd(2+) adsorption was 0.92-1.70 times higher in the amphoteric modified soil compared to unmodified soil. Adsorption isotherms for Cd(2+) displayed a L1-type shape. Phenol adsorption was 1.25-4.35 times higher in the amphoteric modified soil compared to the unmodified control. The adsorption isotherms of phenol on amphoteric modified soils were generally linear, but changed to L1-type isotherms for modified soil in the Cd(2+)+phenol treatment at 40 degrees C. The results clearly showed that amphoteric modified soil had the ability to simultaneously adsorb Cd(2+) and phenol. Cd(2+) adsorption by the amphoteric modified soil was related to the initial concentration of Cd(2+) in the supernatant. Cd(2+) adsorption in the 100BS treatment exceeded adsorption in the 50BS treatment when Cd(2+) initial concentrations were higher than approximate 200 microg mL(-1). Phenol adsorption by modified soils decreased in the order: 100BS>50BS>CK and was primarily determined by the surface hydrophobicity of the soil. For the unmodified soil, total adsorption in the Cd(2+)+phenol treatment was slightly lower compared to treatments that contained only Cd(2+) or phenol. This indicated an antagonistic effect between the adsorption of Cd(2+) and phenol, which was reduced after amphoteric modification. A comparison of temperature effects on Cd(2+) and phenol adsorption indicated that Cd(2+) was both physically and chemically

  7. Atomic and molecular adsorption on Au(111)

    SciTech Connect

    Santiago-Rodríguez, Yohaselly; Herron, Jeffrey A.; Curet-Arana, María C.; Mavrikakis, Manos

    2014-09-01

    Periodic self-consistent density functional theory (DFT-GGA) calculations were used to study the adsorption of several atomic species, molecular species and molecular fragments on the Au(111) surface with a coverage of 1/4 monolayer (ML). Binding geometries, binding energies, and diffusion barriers were calculated for 27 species. Furthermore, we calculated the surface deformation energy associated with the binding events. The binding strength for all the analyzed species can be ordered as follows: NH3 < NO < CO < CH3 < HCO < NH2 < COOH < OH < HCOO < CNH2 < H < N < NH < NOH < COH < Cl,< HCO3 < CH2 < CN b HNO < O < F < S < C < CH. Although the atomic species preferred to bind at the three-fold fcc site, no tendency was observed in site preference for the molecular species and fragments. The intramolecular and adsorbate-surface vibrational frequencies were calculated for all the adsorbates on their most energetically stable adsorption site. Most of the theoretical binding energies and frequencies agreed with experimental values reported in the literature. In general, the values obtained with the PW91 functional are more accurate than RPBE in reproducing these experimental binding energies. The energies of the adsorbed species were used to calculate the thermochemical potential energy surfaces for decomposition of CO, NO, N2, NH3 and CH4, oxidation of CO, and hydrogenation of CO, CO2 and NO, giving insight into the thermochemistry of these reactions on gold nanoparticles. These potential energy surfaces demonstrated that: the decomposition of species is not energetically favorable on Au(111); the desorption of NH3, NO and CO are more favorable than their decomposition; the oxidation of CO and hydrogenation of CO and NO on Au(111) to form HCO and HNO, respectively, are also thermodynamically favorable.

  8. Reservoir capacity estimates in shale plays based on experimental adsorption data

    NASA Astrophysics Data System (ADS)

    Ngo, Tan

    Fine-grained sedimentary rocks are characterized by a complex porous framework containing pores in the nanometer range that can store a significant amount of natural gas (or any other fluids) through adsorption processes. Although the adsorbed gas can take up to a major fraction of the total gas-in-place in these reservoirs, the ability to produce it is limited, and the current technology focuses primarily on the free gas in the fractures. A better understanding and quantification of adsorption/desorption mechanisms in these rocks is therefore required, in order to allow for a more efficient and sustainable use of these resources. Additionally, while water is still predominantly used to fracture the rock, other fluids, such as supercritical CO2 are being considered; here, the idea is to reproduce a similar strategy as for the enhanced recovery of methane in deep coal seams (ECBM). Also in this case, the feasibility of CO2 injection and storage in hydrocarbon shale reservoirs requires a thorough understanding of the rock behavior when exposed to CO2, thus including its adsorption characteristics. The main objectives of this Master's Thesis are as follows: (1) to identify the main controls on gas adsorption in mudrocks (TOC, thermal maturity, clay content, etc.); (2) to create a library of adsorption data measured on shale samples at relevant conditions and to use them for estimating GIP and gas storage in shale reservoirs; (3) to build an experimental apparatus to measure adsorption properties of supercritical fluids (such as CO2 or CH 4) in microporous materials; (4) to measure adsorption isotherms on microporous samples at various temperatures and pressures. The main outcomes of this Master's Thesis are summarized as follows. A review of the literature has been carried out to create a library of methane and CO2 adsorption isotherms on shale samples from various formations worldwide. Large discrepancies have been found between estimates of the adsorbed gas density

  9. Numerical estimation of adsorption energy distributions from adsorption isotherm data with the expectation-maximization method

    SciTech Connect

    Stanley, B.J.; Guiochon, G. |

    1993-08-01

    The expectation-maximization (EM) method of parameter estimation is used to calculate adsorption energy distributions of molecular probes from their adsorption isotherms. EM does not require prior knowledge of the distribution function or the isotherm, requires no smoothing of the isotherm data, and converges with high stability towards the maximum-likelihood estimate. The method is therefore robust and accurate at high iteration numbers. The EM algorithm is tested with simulated energy distributions corresponding to unimodal Gaussian, bimodal Gaussian, Poisson distributions, and the distributions resulting from Misra isotherms. Theoretical isotherms are generated from these distributions using the Langmuir model, and then chromatographic band profiles are computed using the ideal model of chromatography. Noise is then introduced in the theoretical band profiles comparable to those observed experimentally. The isotherm is then calculated using the elution-by-characteristic points method. The energy distribution given by the EM method is compared to the original one. Results are contrasted to those obtained with the House and Jaycock algorithm HILDA, and shown to be superior in terms of robustness, accuracy, and information theory. The effect of undersampling of the high-pressure/low-energy region of the adsorption is reported and discussed for the EM algorithm, as well as the effect of signal-to-noise ratio on the degree of heterogeneity that may be estimated experimentally.

  10. Metal adsorption by agricultural biosorbents: Adsorption isotherm, kinetic and biosorbents chemical structures.

    PubMed

    Sadeek, Sadeek A; Negm, Nabel A; Hefni, Hassan H H; Wahab, Mostafa M Abdel

    2015-11-01

    Biosorption of Cu(II), Co(II) and Fe(III) ions from aqueous solutions by rice husk, palm leaf and water hyacinth was investigated as a function of initial pH, initial heavy metal ions concentration and treatment time. The adsorption process was examined by two adsorption isotherms: Langmuir and Freundlich isotherms. The experimental data of biosorption process were analyzed using pseudo-first order, pseudo-second order kinetic models. The equilibrium biosorption isotherms showed that the three studied biosorbents possess high affinity and sorption capacity for Cu(II), Co(II) and Fe(III) ions. Rice husk showed more efficiency than palm leaf and water hyacinth. Adsorption of Cu(II) and Co(II) was more efficient in alkaline medium (pH 9) than neutral medium due to the high solubility of metal ion complexes. The metal removal efficiency of each biosorbent was correlated to its chemical structure. DTA studies showed formation of metal complex between the biosorbents and the metal ions. The obtained results showed that the tested biosorbents are efficient and alternate low-cost biosorbent for removal of heavy metal ions from aqueous media.

  11. Adsorption sites, adsorption enthalpies and potential removal of terpenoids by atmospheric ice

    NASA Astrophysics Data System (ADS)

    Czech, Christian; Hammer, Sonja M.; Bonn, Boris; Schmidt, Martin U.

    2011-01-01

    Ice crystal formation and its effect on atmospheric trace gases are currently an important area of research because of its radiation and climate effects. However, the processes of adsorption of trace gases on ice surfaces and absorption into ice crystals are poorly understood. Both processes are investigated by lattice-energy minimisation for a selected number of atmospherically relevant volatile organic compounds, i.e. isoprene, methacrolein, acetone, methylbutenol, perillyl alcohol and 2,10-pinanediol, which can be considered as exemplary substances for similar structured compounds. Adsorption and absorption geometries and enthalpies are computed and the potential uptake strength is approximated. According to our calculations non-polar terpenes like isoprene are not significantly adsorbed by ice crystals. Oxidized terpenoids have stronger interactions with the ice surface (at least two hydrogen bonds) leading to larger adsorption enthalpies. Absorption into the ice crystal plays only a minor role. Correspondingly, in the atmosphere terpenoid compounds are increasingly adsorbed to ice surfaces with increasing oxygen numbers. Subsequently this process can contribute to the wet removal of terpenoids by ice, which is so far ignored in global transport models.

  12. Modeling Adsorption and Reactions of Organic Molecules at Metal Surfaces

    PubMed Central

    2014-01-01

    Conspectus The understanding of adsorption and reactions of (large) organic molecules at metal surfaces plays an increasingly important role in modern surface science and technology. Such hybrid inorganic/organic systems (HIOS) are relevant for many applications in catalysis, light-emitting diodes, single-molecule junctions, molecular sensors and switches, and photovoltaics. Obviously, the predictive modeling and understanding of the structure and stability of such hybrid systems is an essential prerequisite for tuning their electronic properties and functions. At present, density-functional theory (DFT) is the most promising approach to study the structure, stability, and electronic properties of complex systems, because it can be applied to both molecules and solids comprising thousands of atoms. However, state-of-the-art approximations to DFT do not provide a consistent and reliable description for HIOS, which is largely due to two issues: (i) the self-interaction of the electrons with themselves arising from the Hartree term of the total energy that is not fully compensated in approximate exchange-correlation functionals, and (ii) the lack of long-range part of the ubiquitous van der Waals (vdW) interactions. The self-interaction errors sometimes lead to incorrect description of charge transfer and electronic level alignment in HIOS, although for molecules adsorbed on metals these effects will often cancel out in total energy differences. Regarding vdW interactions, several promising vdW-inclusive DFT-based methods have been recently demonstrated to yield remarkable accuracy for intermolecular interactions in the gas phase. However, the majority of these approaches neglect the nonlocal collective electron response in the vdW energy tail, an effect that is particularly strong in condensed phases and at interfaces between different materials. Here we show that the recently developed DFT+vdWsurf method that accurately accounts for the collective electronic

  13. Modeling adsorption and reactions of organic molecules at metal surfaces.

    PubMed

    Liu, Wei; Tkatchenko, Alexandre; Scheffler, Matthias

    2014-11-18

    CONSPECTUS: The understanding of adsorption and reactions of (large) organic molecules at metal surfaces plays an increasingly important role in modern surface science and technology. Such hybrid inorganic/organic systems (HIOS) are relevant for many applications in catalysis, light-emitting diodes, single-molecule junctions, molecular sensors and switches, and photovoltaics. Obviously, the predictive modeling and understanding of the structure and stability of such hybrid systems is an essential prerequisite for tuning their electronic properties and functions. At present, density-functional theory (DFT) is the most promising approach to study the structure, stability, and electronic properties of complex systems, because it can be applied to both molecules and solids comprising thousands of atoms. However, state-of-the-art approximations to DFT do not provide a consistent and reliable description for HIOS, which is largely due to two issues: (i) the self-interaction of the electrons with themselves arising from the Hartree term of the total energy that is not fully compensated in approximate exchange-correlation functionals, and (ii) the lack of long-range part of the ubiquitous van der Waals (vdW) interactions. The self-interaction errors sometimes lead to incorrect description of charge transfer and electronic level alignment in HIOS, although for molecules adsorbed on metals these effects will often cancel out in total energy differences. Regarding vdW interactions, several promising vdW-inclusive DFT-based methods have been recently demonstrated to yield remarkable accuracy for intermolecular interactions in the gas phase. However, the majority of these approaches neglect the nonlocal collective electron response in the vdW energy tail, an effect that is particularly strong in condensed phases and at interfaces between different materials. Here we show that the recently developed DFT+vdW(surf) method that accurately accounts for the collective electronic

  14. Relationship between the adsorption capacity of pesticides by wood residues and the properties of woods and pesticides.

    PubMed

    Rodriguez-Cruz, Sonia; Andrades, Maria S; Sanchez-Camazano, Maria; Sanchez-Martin, Maria J

    2007-05-15

    With the aim to explore the potential use of wood residues in technologies aimed at preventing the pollution of soil and water, we studied the adsorption of four non-ionic pesticides (linuron, alachlor, metalaxyl, and chlorpyrifos) and two ionic pesticides (dicamba and paraquat) with a Kow range of -4.5 to 4.7 by nine types of wood with lignin content in the 18.2-26.9% range. The Freundlich Kf values were considered as indicators of the adsorption capacity. A statistical study was carried out using simple and multiple correlations to establish the degree to which the different parameters of the woods and of the pesticides were involved in adsorption. In the case of the non-ionic pesticides, positive and negative significant correlations were observed between Kf and the lignin (r = 0.73-0.83, p < 0.05-0.01), and soluble C contents of the woods (r = 0.66-0.84), p < 0.1-0.01). For dicamba, a correlation between Kf and pH (r = -0.66, p < 0.1) of the woods was found, while for paraquat, this was seen between Kf and the cation exchange capacity (r = 0.71, p < 0.1) of the woods. No significant correlation was observed between Kf and the total C content of the woods. A highly significant correlation between Kf and Kow values (r > or = 0.93, p < 0.01) was found in the adsorption of the pesticides by the woods (with the exception of paraquat) showing that this parameter is very important in this adsorption process. The determination coefficient of the multiple correlation between Kf and the parameters Kow, soluble C, and lignin contents accounts for nearly 100% of the variability in adsorption for non-ionic pesticides. Based on the results of our study and of those of the literature related to the adsorption of aromatic hydrocarbons, we used the Kow values to define a predictive model of adsorption of hydrophobic organic compounds in general by the woods.

  15. Modification of a magnetic carbon composite for ciprofloxacin adsorption.

    PubMed

    Mao, Haixin; Wang, Shikui; Lin, Jian-Ying; Wang, Zengshuang; Ren, Jun

    2016-11-01

    A magnetic carbon composite, Fe3O4/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere (N2), and then used as an adsorbent for ciprofloxacin (CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry, scanning electron microscopy, transmission electron microscopy, and N2 adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.

  16. Boronate affinity adsorption of RNA: possible role of conformational changes

    NASA Technical Reports Server (NTRS)

    Singh, N.; Willson, R. C.; Fox, G. E. (Principal Investigator)

    1999-01-01

    Batch equilibrium adsorption isotherm determination is used to characterize the adsorption of mixed yeast RNA on agarose-immobilized m-aminophenylboronic acid. It is shown that the affinity-enhancing influence of divalent cations depends strongly on the precise nature of the cation used, with barium being far more effective than the conventionally-used magnesium. This adsorption-promoting influence of barium is suggested to arise primarily from ionic influences on the structure and rigidity of the RNA molecule, as the adsorption of ribose-based small molecules is not similarly affected. The substitution of barium for the standard magnesium counterion does not greatly promote the adsorption of DNA, implying that the effect is specific to RNA and may be useful in boronate-based RNA separations. RNA adsorption isotherms exhibit sharp transitions as functions of temperature, and these transitions occur at different temperatures with Mg2+ and with Ba2+. Adsorption affinity and capacity were found to increase markedly at lower temperatures, suggestive of an enthalpically favored interaction process. The stoichiometric displacement parameter, Z, in Ba2+ buffer is three times the value in Mg2+ buffer, and is close to unity.

  17. Laboratory investigation of steam adsorption in geothermal reservoir rocks

    SciTech Connect

    Luetkehans, J.

    1988-02-01

    Some vapor-dominated geothermal reservoirs and low-permeability gas reservoirs exhibit anomalous behavior that may be caused by surface adsorption. For example, geothermal reservoirs in the Larderello are of Italy and reservoirs in the Geysers Geothermal Field, California produce little, if any, liquid. Yet to satisfy material balance constraints, another phase besides steam must be present. If steam adsorption occurring in significant amounts is not accounted for, the reserves will be grossly under-estimated. In addition, well tests may be misinterpreted because the pressure response is delayed owing to be adsorbed material leaving or entering the gaseous phase. In the present research the role of adsorption in geothermal reservoirs in investigated. Two sets of laboratory equipment were constructed to measure adsorption isotherms of cores from Berea sandstone, Larderello, and The Geysers. Seven experimental runs were completed using nitrogen on the low temperature apparatus at -196/sup 0/C. Eight runs were conducted using steam on the high temperature apparatus at temperatures ranging from 150 C to 207/sup 0/C. The largest specific surface area and the greatest nitrogen adsorption isotherm were measured on the Berea sandstone, followed by a core from Larderello and then The Geysers. Difficulties in determining whether a system had reached equilibrium at the end of each step lead to questions regarding the magnitude of adsorption measured by the steam runs. Nevertheless, adsorption was observed and the difficulties themselves were useful indicators of needed future research.

  18. Adsorption of cadmium by sulphur dioxide treated activated carbon.

    PubMed

    Macías-García, A; Gómez-Serrano, V; Alexandre-Franco, M F; Valenzuela-Calahorro, C

    2003-10-01

    Merck carbon (1.5 mm) was treated in three ways: heating from ambient temperature to 900 degrees C in SO(2); treatment at ambient temperature in SO(2); or successive treatments in SO(2) and H(2)S at ambient temperature. All samples were then characterised and tested as adsorbents of Cd(2+) from aqueous solution. The characterisation was in terms of composition by effecting ultimate and proximate analyses and also of textural properties by N(2) adsorption at -196 degrees C. Kinetics and extent of the adsorption process of Cd(2+) were studied at 25 and 45 degrees C at pH of the Cd(2+) solution (i.e., 6.2) and at 25 degrees C also at pH 2.0. The various treatments of the starting carbon had no significant effect on the kinetics of the adsorption of Cd(2+), but increased its adsorption capacity. The most effective treatment was heating to 900 degrees C, the adsorption in this case being 70.3% more than that of the starting carbon. The adsorption increased at 45 degrees C but decreased at pH 2.0 when compared to adsorption at 25 degrees C and pH 6.2, respectively.

  19. Arsenate adsorption onto iron oxide amended rice husk char.

    PubMed

    Cope, Christopher O; Webster, Damon S; Sabatini, David A

    2014-08-01

    In this study, rice husks were charred at 550 °C in a partially sealed ceramic vessel for 30minutes to create a high specific surface area (SSA) rice husk char (RHC). The RHC was then amended with iron oxides using dissolved ferric nitrate, Fe(NO3)3⋅9H2O, to provide a surface chemistry conducive to arsenic adsorption. The 550 °C iron oxide amended rice husk char's (550 IOA-RHC's) SSA was nearly 2.5 orders of magnitude higher and the arsenate adsorptive level was nearly 2 orders of magnitude higher than those reported for iron oxide amended sand, thus indicating a positive relationship between post-amendment SSA and arsenate adsorptive levels. Rice husks were then charred at temperatures ranging from 450 °C to 1050 °C to create an even higher SSA material, which might further increase arsenate adsorptive levels. The 950 °C RHC was chosen for amendment due to its high SSA and feasibility of being produced in the field. Once amended, the 950 °C iron oxide amended rice husk char (950 IOA-RHC) improved the arsenate adsorption capacity by thus confirming a positive relationship, though not a linear relationship, between post-amendment SSA and arsenic adsorptive capacity. Further study demonstrated that post-amendment mesoporous volume and mesoporous surface area appear to be better indicators of arsenic adsorptive capacity than SSA or iron content.

  20. Neon and CO2 adsorption on open carbon nanohorns.

    PubMed

    Krungleviciute, Vaiva; Ziegler, Carl A; Banjara, Shree R; Yudasaka, Masako; Iijima, S; Migone, Aldo D

    2013-07-30

    We present the results of a thermodynamics and kinetics study of the adsorption of neon and carbon dioxide on aggregates of chemically opened carbon nanohorns. Both the equilibrium adsorption characteristics, as well as the dependence of the kinetic behavior on sorbent loading, are different for these two adsorbates. For neon the adsorption isotherms display two steps before reaching the saturated vapor pressure, corresponding to adsorption on strong and on weak binding sites; the isosteric heat of adsorption is a decreasing function of sorbent loading (this quantity varies by about a factor of 2 on the range of loadings studied), and the speed of the adsorption kinetics increases with increasing loading. By contrast, for carbon dioxide there are no substeps in the adsorption isotherms; the isosteric heat is a nonmonotonic function of loading, the value of the isosteric heat never differs from the bulk heat of sublimation by more than 15%, and the kinetic behavior is opposite to that of neon, with equilibration times increasing for higher sorbent loadings. We explain the difference in the equilibrium properties observed for neon and carbon dioxide in terms of differences in the relative strengths of adsorbate-adsorbate to adsorbate-sorbent interaction for these species.

  1. Adsorption of Compounds that Mimic Urban Stormwater Dissolved Organic Nitrogen.

    PubMed

    Mohtadi, Mehrdad; James, Bruce R; Davis, Allen P

    2017-02-01

      Stormwater runoff carrying nitrogen can accelerate eutrophication. Bioretention facilities are among low impact development systems which are commonly used to manage urban stormwater quality and quantity. They are, however, not designed to remove dissolved organic nitrogen (DON) and may become a net DON exporter. Adsorption of seven organic nitrogenous compounds onto several adsorbents was examined. Batch adsorption study revealed that coal activated carbon (AC) exhibited the best performance in adsorption of the selected organic nitrogenous compounds. The highest adsorption capacity of coal AC was 0.4 mg N/g for pyrrole at an equilibrium concentration of 0.02 mg N/L, while adsorption was not detectable for urea at the same equilibrium concentration. The fastest compound to reach equilibrium adsorption capacity onto the coal AC was pyrrole (1 hour). The adsorption capacity of the coal AC for pyrrole and N-acetyl-d-glucosamine and 1-hour contact time is recommended for designing bioretention systems targeting organic nitrogenous compounds.

  2. Hydrogen adsorption on sulphur-doped SiC nanotubes

    NASA Astrophysics Data System (ADS)

    Sevak Singh, Ram

    2016-07-01

    Hydrogen (H2) is an energy carrier and clean fuel that can be used for a broad range of applications that include fuel cell vehicles. Therefore, development of materials for hydrogen storage is demanded. Nanotubes, in this context, are appropriate materials. Recently, silicon carbide nanotube (SiCNTs) have been predicted as potential nanomaterials for hydrogen storage, and atomic doping into the nanotubes improves the H2 adsorption. Here, we report H2 adsorption properties of sulphur-doped (S-doped) SiCNTs using first-principles calculations based on density functional theory. The H2 adsorption properties are investigated by calculations of energy band structures, density of states (DOS), adsorption energy and Mulliken charge population analysis. Our findings show that, compared to the intrinsic SiCNT, S-doped SiCNT is more sensitive to H2 adsorption. H2 gas adsorption on S-doped C-sites of SiCNT brings about significant modulation of the electronic structure of the nanotube, which results in charge transfer from the nanotube to the gas, and dipole-dipole interactions cause chemisorptions of hydrogen. However, in the case of H2 gas adsorption on S-doped Si-sites of the nanotube, lesser charge transfer from the nanotube to the gas results in physisorptions of the gas. The efficient hydrogen sensing properties of S-doped SiCNTs, studied here, may have potential for its practical realization for hydrogen storage application.

  3. Measuring and modeling ammonium adsorption by calcareous soils.

    PubMed

    Ranjbar, F; Jalali, M

    2013-04-01

    The aim of this study was assessment of ammonium (NH 4(+) ) adsorption isotherms in some agricultural calcareous soils and modeling of that by using the mechanistic exchange model. Ten surface soils (0-30 cm) were collected from areas covered with different land uses in Hamedan, western Iran. Isotherm experiments were carried out by concentrations of NH 4(+) prepared from NH4Cl salt (0, 10, 20, 30, 40, 50, 100, and 150 mg NH 4(+)  l(-1)) in presence of 0.01 M CaCl2 solution. The empirical models including simple adsorption isotherm and Freundlich equations were fitted well to the experimental data. The average amounts of adsorbed NH 4(+) in studied soils varied from 8.95 to 35.23 %. Adsorption percentage indicated positive correlation with pH, cation-exchange capacity (CEC), equivalent calcium carbonate, and clay content and had negative correlation with sand content. In order to predict and model NH 4(+) adsorption, cation-exchange model in PHREEQC program was used. The model could simulate the NH 4(+) adsorption very well in all studied soils. The values of CEC played the major role in modeling of NH 4(+) adsorption in this study indicating that cation-exchange process was the major mechanism controlling NH 4(+) adsorption in studied soils.

  4. Temperature-dependent adsorption of nitrogen on porous vycor glass

    NASA Astrophysics Data System (ADS)

    Huber, Tito E.; Tsou, Hsi Lung

    1998-03-01

    Adsorption isotherms of N2 have been measured in the temperature range from 77 to 120 K in samples of porous vycor glass. From the Brunauer-Emmett-Teller theory the surface layer coverages are determined. These are found to be temperature dependent. When adsorption-isotherm coverage data are expressed as a function of the adsorption potential δμ, the result is roughly temperature independent for coverages ranging from submonolayer to thin film, below capillary condensation. This characteristic curve, which represents the distribution of adsorption sites vs the adsorption potential, is compared with results from two models for the adsorbate: Dubinin's isotherm for microporous solids and its extension to rough surfaces, which places importance on the porosity of the surface, and Halsey's extension of the Frankel-Halsey-Hill isotherm, which takes into account the long-range variations of the substrate adsorption potential. The impact of this work on the interpretation of N2 adsorption data in terms of a surface area is discussed.

  5. Synthesis of magnetic wheat straw for arsenic adsorption.

    PubMed

    Tian, Ye; Wu, Min; Lin, Xiaobo; Huang, Pei; Huang, Yong

    2011-10-15

    Magnetic wheat straw (MWS) with different Fe(3)O(4) content was synthesized by using in-situ co-precipitation method. It was characterized by powder X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). This material can be used for arsenic adsorption from water, and can be easily separated by applied magnetic field. The introduction of wheat straw template highly enhanced the arsenic adsorption of Fe(3)O(4). Among three adsorption isotherm models examined, the data fitted Langmuir model better. Fe(3)O(4) content and initial pH value influenced its adsorption behavior. Higher Fe(3)O(4) content corresponded to a higher adsorption capacity. In the pH range of 3-11, As(V) adsorption was decreased with increasing of pH; As(III) adsorption had the highest capacity at pH 7-9. Moreover, by using 0.1 mol L(-1) NaOH aqueous solution, it could be regenerated. This work provided an efficient way for making use of agricultural waste.

  6. Kinetics and isotherms of Neutral Red adsorption on peanut husk.

    PubMed

    Han, Runping; Han, Pan; Cai, Zhaohui; Zhao, Zhenhui; Tang, Mingsheng

    2008-01-01

    Adsorption of Neutral Red (NR) onto peanut husk in aqueous solutions was investigated at 295 K. Experiments were carried out as function of pH, adsorbent dosage, contact time, and initial concentration. The equilibrium adsorption data were analyzed by Langmuir, Freundlich, Temkin, Dubinin-Radushkevich, and Toth isotherm models. The results indicated that the Toth and Langmuir models provided the best correlation of the experimental data. The adsorption capacity of peanut husk for the removal of NR was determined with the Langmuir and found to be 37.5 mg/g at 295 K. The adsorption kinetic data were modeled using the pseudo-first order, pseudo-second order, and intra-particle diffusion kinetic equations. It was seen that the pseudo-first order and pseudo-second order kinetic equations could describe the adsorption kinetics. The intraparticle diffusion model was also used to express the adsorption process at the two-step stage. It was implied that peanut husk may be suitable as adsorbent material for adsorption of NR from aqueous solutions.

  7. Possibility of using adsorption refrigeration unit in district heating network

    NASA Astrophysics Data System (ADS)

    Grzebielec, Andrzej; Rusowicz, Artur; Jaworski, Maciej; Laskowski, Rafał

    2015-09-01

    Adsorption refrigeration systems are able to work with heat sources of temperature starting with 50 °C. The aim of the article is to determine whether in terms of technical and economic issues adsorption refrigeration equipment can work as elements that produce cold using hot water from the district heating network. For this purpose, examined was the work of the adsorption air conditioning equipment cooperating with drycooler, and the opportunities offered by the district heating network in Warsaw during the summer. It turns out that the efficiency of the adsorption device from the economic perspective is not sufficient for production of cold even during the transitional period. The main problem is not the low temperature of the water supply, but the large difference between the coefficients of performance, COPs, of adsorption device and a traditional compressor air conditioning unit. When outside air temperature is 25 °C, the COP of the compressor type reaches a value of 4.49, whereas that of the adsorption device in the same conditions is 0.14. The ratio of the COPs is 32. At the same time ratio between the price of 1 kWh of electric power and 1 kWh of heat is only 2.85. Adsorption refrigeration equipment to be able to compete with compressor devices, should feature COPads efficiency to be greater than 1.52. At such a low driving temperature and even changing the drycooler into the evaporative cooler it is not currently possible to achieve.

  8. Adsorption-driven translocation of polymer chain into nanopores

    NASA Astrophysics Data System (ADS)

    Yang, Shuang; Neimark, Alexander V.

    2012-06-01

    The polymer translocation into nanopores is generally facilitated by external driving forces, such as electric or hydrodynamic fields, to compensate for entropic restrictions imposed by the confinement. We investigate the dynamics of translocation driven by polymer adsorption to the confining walls that is relevant to chromatographic separation of macromolecules. By using the self-consistent field theory, we study the passage of a chain trough a small opening from cis to trans compartments of spherical shape with adsorption potential applied in the trans compartment. The chain transfer is modeled as the Fokker-Plank diffusion along the free energy landscape of the translocation pass represented as a sum of the free energies of cis and trans parts of the chain tethered to the pore opening. We investigate how the chain length, the size of trans compartment, the magnitude of adsorption potential, and the extent of excluded volume interactions affect the translocation time and its distribution. Interplay of these factors brings about a variety of different translocation regimes. We show that excluded volume interactions within a certain range of adsorption potentials can cause a local minimum on the free energy landscape, which is absent for ideal chains. The adsorption potential always leads to the decrease of the free energy barrier, increasing the probability of successful translocation. However, the translocation time depends non-monotonically of the magnitude of adsorption potential. Our calculations predict the existence of the critical magnitude of adsorption potential, which separates favorable and unfavorable regimes of translocation.

  9. Amino-functionalized cotton fiber for enhanced adsorption of active brilliant red X-3B from aqueous solution.

    PubMed

    Deng, Hui; Ning, JiaHong; Wang, XiaoNing

    2016-12-01

    An amino-functionalized sorbent (ACF) was prepared by grafting amine group onto cotton fiber (CF) using tetraethylenepentamine (TEPA). The resulting composite was characterized using various instrumental techniques such as scanning electron microscopy (SEM), Fourier transformed infrared (FTIR) and pHpzc analysis. FTIR spectrum and pHpzc analysis illustrated the involvement of amine groups in the X-3B sorption process. ACF sorbent was tested for its ability to remove X-3B from an aqueous solution in batch experiments. The adsorption efficiency of ACF was 100% in comparison with 5.52% of raw cotton fiber when initial concentration of active brilliant red X-3B was 30 mg/l. Results suggested that solution pH hardly affected the removal of X-3B, and ACF remained stable sorption efficiency in the pH range of 3.0-12.0. High values of correlation coefficients indicated the adsorption kinetics could best described by the pseudo-second-order kinetic equation. The sorption isotherm of ACF fitted the Langmuir equilibrium model, with the maximum adsorption capacity of 270.27 mg/g at 293K. The obtained thermodynamic parameters showed that the adsorption of X-3B onto the adsorbent was spontaneous and exothermic. The excellent regeneration performance provided strong evidence of the potential of ACF for technological applications of dye removal.

  10. Microwave-swing adsorption to capture and recover vapors from air streams with activated carbon fiber cloth.

    PubMed

    Hashisho, Zaher; Rood, Mark; Botich, Leon

    2005-09-01

    Adsorption with regeneration is a desirable means to control the emissions of organic vapors such as hazardous air pollutants (HAPs) and volatile organic compounds (VOCs) from air streams as it allows for capture, recovery, and reuse of those VOCs/HAPS. Integration of activated-carbon fiber-cloth (ACFC) adsorbent with microwave regeneration provides promise as a new adsorption/ regeneration technology. This research investigates the feasibility of using microwaves to regenerate ACFC as part of a process for capture and recovery of organic vapors from gas streams. A bench-scale fixed-bed microwave-swing adsorption (MSA) system was built and tested for adsorption of water vapor, methyl ethyl ketone (MEK), and tetrachloroethylene (PERC) from an airstream and then recovery of those vapors with microwave regeneration. The electromagnetic heating behavior of dry and vapor-saturated ACFC was also characterized. The MSA system successfully adsorbed organic vapors from the airstreams, allowed for rapid regeneration of the ACFC cartridge, and recovered the water and organic vapors as liquids.

  11. Characterization of individual molecular adsorption geometries by atomic force microscopy: Cu-TCPP on rutile TiO2 (110)

    NASA Astrophysics Data System (ADS)

    Jöhr, Res; Hinaut, Antoine; Pawlak, Rémy; Sadeghi, Ali; Saha, Santanu; Goedecker, Stefan; Such, Bartosz; Szymonski, Marek; Meyer, Ernst; Glatzel, Thilo

    2015-09-01

    Functionalized materials consisting of inorganic substrates with organic adsorbates play an increasing role in emerging technologies like molecular electronics or hybrid photovoltaics. For such applications, the adsorption geometry of the molecules under operating conditions, e.g., ambient temperature, is crucial because it influences the electronic properties of the interface, which in turn determine the device performance. So far detailed experimental characterization of adsorbates at room temperature has mainly been done using a combination of complementary methods like photoelectron spectroscopy together with scanning tunneling microscopy. However, this approach is limited to ensembles of adsorbates. In this paper, we show that the characterization of individual molecules at room temperature, comprising the determination of the adsorption configuration and the electrostatic interaction with the surface, can be achieved experimentally by atomic force microscopy (AFM) and Kelvin probe force microscopy (KPFM). We demonstrate this by identifying two different adsorption configurations of isolated copper(ii) meso-tetra (4-carboxyphenyl) porphyrin (Cu-TCPP) on rutile TiO2 (110) in ultra-high vacuum. The local contact potential difference measured by KPFM indicates an interfacial dipole due to electron transfer from the Cu-TCPP to the TiO2. The experimental results are verified by state-of-the-art first principles calculations. We note that the improvement of the AFM resolution, achieved in this work, is crucial for such accurate calculations. Therefore, high resolution AFM at room temperature is promising for significantly promoting the understanding of molecular adsorption.

  12. Characterization of individual molecular adsorption geometries by atomic force microscopy: Cu-TCPP on rutile TiO2 (110).

    PubMed

    Jöhr, Res; Hinaut, Antoine; Pawlak, Rémy; Sadeghi, Ali; Saha, Santanu; Goedecker, Stefan; Such, Bartosz; Szymonski, Marek; Meyer, Ernst; Glatzel, Thilo

    2015-09-07

    Functionalized materials consisting of inorganic substrates with organic adsorbates play an increasing role in emerging technologies like molecular electronics or hybrid photovoltaics. For such applications, the adsorption geometry of the molecules under operating conditions, e.g., ambient temperature, is crucial because it influences the electronic properties of the interface, which in turn determine the device performance. So far detailed experimental characterization of adsorbates at room temperature has mainly been done using a combination of complementary methods like photoelectron spectroscopy together with scanning tunneling microscopy. However, this approach is limited to ensembles of adsorbates. In this paper, we show that the characterization of individual molecules at room temperature, comprising the determination of the adsorption configuration and the electrostatic interaction with the surface, can be achieved experimentally by atomic force microscopy (AFM) and Kelvin probe force microscopy (KPFM). We demonstrate this by identifying two different adsorption configurations of isolated copper(ii) meso-tetra (4-carboxyphenyl) porphyrin (Cu-TCPP) on rutile TiO2 (110) in ultra-high vacuum. The local contact potential difference measured by KPFM indicates an interfacial dipole due to electron transfer from the Cu-TCPP to the TiO2. The experimental results are verified by state-of-the-art first principles calculations. We note that the improvement of the AFM resolution, achieved in this work, is crucial for such accurate calculations. Therefore, high resolution AFM at room temperature is promising for significantly promoting the understanding of molecular adsorption.

  13. Whispering Gallery Mode Biosensor Quantification of Fibronectin Adsorption Kinetics onto Alkylsilane Monolayers and Interpretation of Resultant Cellular Response

    PubMed Central

    Wilson, Kerry A.; Finch, Craig A.; Anderson, Phillip; Vollmer, Frank; Hickman, James J.

    2011-01-01

    A Whispering Gallery Mode (WGM) biosensor was constructed to measure the adsorption of protein onto alkysilane self-assembled monolayers (SAMs) at solution concentrations unattainable with other techniques. The high sensitivity was provided by a WGM resonance excited in a silica microsphere that was functionalized with alkylsilane SAMs and integrated in a microfluidic flow cell under laminar flow conditions. It was found that FN adsorbed at biologically relevant surface densities, however, the adsorption kinetics and concentration dependent saturation values varied significantly from work published utilizing alkanethiol SAMs. Mathematical models were applied to the experimental results to interpret the observed kinetics of FN adsorption. Embryonic hippocampal neurons and skeletal myoblasts were cultured on the modified surfaces, and a live-dead assay was used to determine the viability of the FN surfaces for cell culture, and major differences were noted in the biological response to the different SAMs. The high sensitivity and simplicity of the WGM biosensor, combined with its ability to quantify the adsorption of any dilute protein in a label-free assay, establishes the importance of this technology for the study of surface accretion and its effect on cellular function, which can affect biomaterials for both in vivo and in vitro applications. PMID:21983134

  14. Physico-chemical characterization of metal-doped bone chars and their adsorption behavior for water defluoridation

    NASA Astrophysics Data System (ADS)

    Rojas-Mayorga, C. K.; Bonilla-Petriciolet, A.; Silvestre-Albero, J.; Aguayo-Villarreal, I. A.; Mendoza-Castillo, D. I.

    2015-11-01

    New bone chars for fluoride adsorption from drinking water have been synthetized via metallic doping using aluminum and iron salts. A detailed statistical analysis of the metal doping process using the signal-to-noise ratios from Taguchi's experimental designs and its impact on the fluoride adsorption properties of modified bone chars have been performed. The best conditions, including the proper metallic salt, for metal doping were identified to improve the fluoride uptakes of modified bone chars. Results showed that the fluoride adsorption properties of bone chars can be enhanced up to 600% using aluminum sulfate for the surface modification. This aluminum-based adsorbent showed an adsorption capacity of 31 mg/g, which outperformed the fluoride uptakes reported for several adsorbents. Surface interactions involved in the defluoridation process were established using FTIR, DRX and XPS analysis. Defluoridation using the metal-doped bone chars occurred via an ion exchange process between fluoride ions and the hydroxyl groups on the adsorbent surface, whereas the Al(OH)xFy, FexFy, and CaF2 interactions could play also an important role in the removal process. These metal-doped adsorbents anticipate a promising behavior in water treatment, especially in developing countries where the efficiency - cost tradeoff is crucial for implementing new defluoridation technologies.

  15. Amine Swingbed Payload Technology Demonstration

    NASA Technical Reports Server (NTRS)

    Sweterlitsch, Jeffrey

    2014-01-01

    The Amine Swingbed is an amine-based, vacuum-regenerated adsorption technology for removing carbon dioxide and humidity from a habitable spacecraft environment, and is the baseline technology for the Orion Program’s Multi-Purpose Crew Vehicle (MPCV). It uses a pair of interleaved-layer beds filled with SA9T, the amine sorbent, and a linear multiball valve rotates 270° back and forth to control the flow of air and vacuum to adsorbing and desorbing beds. One bed adsorbs CO2 and H2O from cabin air while the other bed is exposed to vacuum for regeneration by venting the CO2 and H2O. The two beds are thermally linked, so no additional heating or cooling is required. The technology can be applied to habitable environments where recycling CO2 and H2O is not required such as short duration missions.

  16. [Kinetics of adsorption of Pb2+ onto small river sediment].

    PubMed

    Shi, Gui-Tao; Chen, Zhen-Lou; Bi, Chun-Juan; Sun, Chao; Sun, Yue-Di; Xu, Shi-Yuan

    2009-06-15

    The batch experiments of adsorption of Pb2+ onto small river sediments were conducted. The kinetics of the sorption process was analyzed. The results showed that the equilibrium time of adsorption increased with the increasing of sediment mass in solution, while both adsorbed Pb2+ on per unit of sediment and Pb2+ concentration in the solution after equilibrium decreased. More than 95% of Pb2+ in solution was removed when sediment contents larger than 0.6 g x L(-1). Both pseudo-first-order and pseudo-second-order kinetics were tested and it was found that the latter gave a better explanation of the adsorption process. The equilibrium adsorption capacities calculated from the pseudo-second-order model could represent the true value. There was no significant correlation between initial adsorption rate of Pb2+ and the amount of sediment in solution. However, the pseudo-second-order rate constant increased in the solution with more adsorbent, namely chemical adsorption controlled the process. Elovich equation could explain the mechanism of sorption in the solution with higher contents of sediment; nevertheless, the process of low concentration of adsorbent adsorbing Pb2+ disagreed well with Elovich equation. In terms of adsorption rate in the sorption, intra-particle diffusion dominated in the more sediment solution. On the other hand, multi-linearity was presented for the adsorption rate in less adsorbent solution. The first, sharper portion represented adsorption on the external surface. The second portion indicated Pb2+ diffused gradually into the interior of particles and intra-particle diffusion controlled.

  17. Variability of mitomycin C adsorption by activated charcoal.

    PubMed

    Shah, I A; Lindup, W E; McCulloch, P G

    1998-03-01

    A saline suspension of mitomycin C adsorbed on activated charcoal and administered intraperitoneally has been reported to be safe and effective in the treatment of gastric carcinoma. Activated charcoal specifically targets tumour and lymph-node tissues and the sustained higher local drug concentration is thought to be beneficial. The charcoal particles used in these suspensions have varied in size from > 147 microm to < 20 nm in diameter, but no data have been published to show how this might affect drug adsorption and delivery. Any variability in drug adsorption could pose a serious clinical risk for drugs with a narrow therapeutic index. We have, therefore, investigated the adsorption of mitomycin C on activated charcoal in-vitro. Activated charcoal was ground and sieved to yield four size-fractions between 180 and 53 microm. Adsorption isotherms (n > or = 3) were constructed and applied to the Freundlich model with 0-l00 microg mL(-1) mitomycin C measured by HPLC with detection at 365 nm. Adsorption of mitomycin C by activated charcoal varied by a factor of three under identical conditions at room temperature (21 degrees C) and at 37 degrees C. The specific adsorption (microg mitomycin C (mg activated charcoal)(-1)) was generally higher at 37 degrees C than at room temperature. The variability of mitomycin C adsorption was greatly reduced by addition of the surface-active agent polyvinylpyrollidone, used to determine that adsorption of mitomycin C was independent of activated charcoal particle size. The characteristics of adsorption of mitomycin C by activated charcoal are complex and should be thoroughly investigated to discover the critical controlling factors before submitting the suspensions for further clinical evaluation.

  18. Influence of alternating current on the adsorption of indigo carmine.

    PubMed

    Kesraoui, Aida; Selmi, Taher; Seffen, Monig; Brouers, François

    2016-08-23

    The main purpose of this work is to study the effect of a new process of accelerating which consist to couple the electrochemical process with the adsorption to remove an anionic dye, the indigo carmine. That is why, we investigated the effects of the new process of accelerating the adsorption process by using alternating current (AC) on the retention of an anionic dye, the indigo carmine. The adsorption capacity of dye (mg/g) was raised with the raise of current voltage in solution, temperature, and initial indigo carmine concentration and decreased with the increase of initial solution pH, current density, and mass of carbon. The results demonstrate that the removal efficiency of 97.0 % with the current voltage of 15 V is achieved at a current density of 0.014 A/cm(2), of pH 2 using zinc as electrodes and contact time of 210 min for adsorption in the presence of AC. Concerning the adsorption without AC, the results obtained showed that for an initial concentration equal to 20 mg/L, more than 95 % amount of adsorbed dye was retained after 405 min of contact in batch system. The comparison between adsorption in the presence and absence of an alternating current shows the importance of the alternating current in the acceleration of the adsorption method and improve the performances of FILTRASORB 200. For both cases, the adsorption mechanism follows the fractal kinetics BSf(n,α) model and the Brouers-Sotolongo isotherm model provides a good fit of the experimental data for both adsorption with and without alternating current.

  19. Performance of an electrothermal swing adsorption system with postdesorption liquefaction for organic gas capture and recovery.

    PubMed

    Mallouk, Kaitlin E; Rood, Mark J

    2013-07-02

    The use of adsorption on activated carbon fiber cloth (ACFC) followed by electrothermal swing adsorption (ESA) and postdesorption pressure and temperature control allows organic gases with boiling points below 0 °C to be captured from air streams and recovered as liquids. This technology has the potential to be a more sustainable abatement technique when compared to thermal oxidation. In this paper, we determine the process performance and energy requirements of a gas recovery system (GRS) using ACFC-ESA for three adsorbates with relative pressures between 8.3 × 10(-5) and 3.4 × 10(-3) and boiling points as low as -26.3 °C. The GRS is able to capture > 99% of the organic gas from the feed air stream, which is comparable to destruction efficiencies for thermal oxidizers. The energy used per liquid mole recovered ranges from 920 to 52,000 kJ/mol and is a function of relative pressure of the adsorbate in the feed gas. Quantifying the performance of the bench-scale gas recovery system in terms of its ability to remove organic gases from the adsorption stream and the energy required to liquefy the recovered organic gases is a critical step in developing new technologies to allow manufacturing to occur in a more sustainable manner. To our knowledge, this is the first time an ACFC-ESA system has been used to capture, recover, and liquefy organic compounds with vapor pressures as low as 8.3 × 10(-5) and the first time such a system has been analyzed for process performance and energy consumption.

  20. Summary of Adsorption Capacity and Adsorption Kinetics of Uranium and Other Elements on Amidoxime-based Adsorbents from Time Series Marine Testing at the Pacific Northwest National Laboratory

    SciTech Connect

    Gill, Gary A.; Kuo, Li-Jung; Strivens, Jonathan E.; Wood, Jordana R.; Schlafer, Nicholas J.; Janke, Christopher J.; Das, Sadananda; Mayes, Richard; Saito, Tomonori; Brown, Suree S.; Tsouris, Constantinos; Tsouris, Costas; Wai, Chien M.; Pan, Horng-Bin

    2016-09-29

    The Pacific Northwest National Laboratory (PNNL) has been conducting marine testing of uranium adsorbent materials for the Fuel Resources Program, Department of Energy, Office of Nuclear Energy (DOE-NE) beginning in FY 2012. The marine testing program is being conducted at PNNL’s Marine Sciences Laboratory (MSL), located at Sequim Bay, along the coast of Washington. One of the main efforts of the marine testing program is the determination of adsorption capacity and adsorption kinetics for uranium and selected other elements (e.g. vanadium, iron, copper, nickel, and zinc) for adsorbent materials provided primarily by Oak Ridge National Laboratory (ORNL), but also includes other Fuel Resources Program participants. This report summarizes the major marine testing results that have been obtained to date using time series sampling for 42 to 56 days using either flow-through column or recirculating flume exposures. The major results are highlighted in this report, and the full data sets are appended as a series of Excel spreadsheet files. Over the four year period (2012-2016) that marine testing of amidoxime-based polymeric adsorbents was conducted at PNNL’s Marine Science Laboratory, there has been a steady progression of improvement in the 56-day adsorbent capacity from 3.30 g U/kg adsorbent for the ORNL 38H adsorbent to the current best performing adsorbent prepared by a collaboration between the University of Tennessee and ORNL to produce the adsorbent SB12-8, which has an adsorption capacity of 6.56 g U/kg adsorbent. This nearly doubling of the adsorption capacity in four years is a significant advancement in amidoxime-based adsorbent technology and a significant achievement for the Uranium from Seawater program. The achievements are evident when compared to the several decades of work conducted by the Japanese scientists beginning in the 1980’s (Kim et al., 2013). The best adsorbent capacity reported by the Japanese scientists was 3.2 g U/kg adsorbent for a

  1. Water vapor adsorption on activated carbon preadsorbed with naphtalene.

    PubMed

    Zimny, T; Finqueneisel, G; Cossarutto, L; Weber, J V

    2005-05-01

    The adsorption of water vapor on a microporous activated carbon derived from the carbonization of coconut shell has been studied. Preadsorption of naphthalene was used as a tool to determine the location and the influence of the primary adsorbing centers within the porous structure of active carbon. The adsorption was studied in the pressure range p/p0=0-0.95 in a static water vapor system, allowing the investigation of both kinetic and equilibrium experimental data. Modeling of the isotherms using the modified equation of Do and Do was applied to determine the effect of preadsorption on the mechanism of adsorption.

  2. Adsorption and diffusion of water on graphene from first principles

    NASA Astrophysics Data System (ADS)

    Ma, Jie; Michaelides, Angelos; Alfè, Dario; Schimka, Laurids; Kresse, Georg; Wang, Enge

    2011-07-01

    Water monomer adsorption on graphene is examined with state-of-the-art electronic structure approaches. The adsorption energy determinations on this system from quantum Monte Carlo and the random-phase approximation yield small values of <100 meV. These benchmarks provide a deeper understanding of the reactivity of graphene that may underpin the development of improved more approximate methods enabling the accurate treatment of more complex processes at wet-carbon interfaces. As an example, we show how dispersion-corrected density functional theory, which we show gives a satisfactory description of this adsorption system, predicts that water undergoes ultra-fast diffusion on graphene at low temperatures.

  3. Adsorption of Cadmium, Nickel and Zinc in a Brazilian Oxisoil

    NASA Astrophysics Data System (ADS)

    Casagrande, José Carlos; Martins, Susian Christian; Soares, Marcio Roberto

    2010-05-01

    The adsorption reactions mechanisms provide the understanding of the pollutant fate metals and often control the bioavailability and transport of heavy metals ions in soil, indicating the preventive environmental control. The cadmium, nickel and zinc behavior in the soils are explained by the reactions of adsorption, influenced by pH and ionic strength. The objective of this work was to study the influence of those factors on cadmium, nickel and zinc adsorption in an oxisol. It was studied the Cd, Ni and Zn adsorption in soil samples of the State of São Paulo (Anionic "Xanthic" Acrudox), collected in surface and in depth and submitted to solutions of Ca(NO3)2 1,0; 0,1 and 0,01 mol L-1. The pH of the samples from 3,0 to 10,0 was varied adding NaOH or HCl 4 mol L-1 not surpassing 2% of the electrolyte volume. The soil samples received 5,0 mg dm-3 of cadmium, nickel and zinc, ratio 1:10 (2,0 g of soil: 20 solution ml) and were shacked for 24 hours. The cadmium, nickel and zinc adsorption increased with pH, reaching it picks at pH 7,0 for cadmium and approximately at pH 6,0 for nickel and zinc. This indicates that zinc and nickel have higher affinity than cadmium with the soil colloids, because it reached the maximum adsorption in a small pH value. In other words, the amount of negative charges necessary to promote the maximum adsorption was small for zinc. The influence of ionic strengths was small for cadmium, nickel and zinc adsorption, being similar from pH 3,0 to 10,0, in surface soil layer and in depth, demonstrating that competition with Ca2+ for the retention colloid sites of the soils didn't interfere in the adsorption. In that way, it is supposed that cadmium, nickel and zinc binding energy is high in a soil rich in Fe and Al oxides. Adsorption of cadmium, nickel and zinc was similar for the ionic strengths, not depending on PZSE. The cadmium, nickel and zinc adsorption increased with pH elevation, with small ionic strength influence. Nickel and zinc have

  4. Effects of oxygen adsorption on carbon nanotube field emitters

    NASA Astrophysics Data System (ADS)

    Park, Noejung; Han, Seungwu; Ihm, Jisoon

    2001-09-01

    Effects of oxygen adsorption on the field emission of carbon nanotubes are studied through first-principles calculations. Calculated emission currents are significantly enhanced when oxygen is adsorbed at the tip and the underlying physics is explained in terms of the change in the electronic structure by oxidation and the local field increase at the adsorption site. The issue of the current degradation accompanied by the oxidative etching is also addressed. The field-emission-microscopy images on the phosphor screen are simulated, displaying various patterns characteristic of each adsorption configuration.

  5. Analysis of the use of adsorption processes in trigeneration systems

    NASA Astrophysics Data System (ADS)

    Grzebielec, Andrzej; Rusowicz, Artur

    2013-12-01

    The trigeneration systems for production of cold use sorption refrigeration machines: absorption and adsorption types. Absorption systems are characterized namely by better cooling coefficient of performance, while the adsorptive systems are characterized by the ability to operate at lower temperatures. The driving heat source temperature can be as low as 60-70 °C. Such temperature of the driving heat source allows to use them in district heating systems. The article focuses on the presentation of the research results on the adsorption devices designed to work in trigeneration systems.

  6. Adsorption and Gas Separation of Molecules by Carbon Nanohorns.

    PubMed

    Gatica, Silvina M; Nekhai, Anton; Scrivener, Adam

    2016-05-19

    In this paper, we report the results of Monte Carlo simulations of the adsorption of neon, argon, methane and carbon dioxide in carbon nanohorns. We model the nanohorns as an array of carbon cones and obtained adsorption isotherms and isosteric heats. The main sites of adsorption are inside the cones and in the interstices between three cones. We also calculated the selectivity of carbon dioxide/methane, finding that nanohorns are a suitable substrate for gas separation. Our simulations are compared to available experimental data.

  7. Experimental adsorption isotherms based on inverse gas chromatography.

    PubMed

    Kalogirou, E; Bassiotis, I; Artemiadi, Th; Margariti, S; Siokos, V; Roubani-Kalantzopoulou, F

    2002-09-06

    A new chromatographic perturbation method is used for studying the adsorption-desorption equilibrium in various gas-solid heterogeneous systems. It is the reversed-flow method giving accurate and precise values of many physicochemical constants including the basic and necessary adsorption isotherm values. For four inorganic oxides, namely, Cr2O3, Fe2O3, TiO2 and PbO, and two aromatic hydrocarbons (benzene, toluene) these adsorption isotherms have been determined through a non-linear model.

  8. Predicting protein dynamic binding capacity from batch adsorption tests.

    PubMed

    Carta, Giorgio

    2012-10-01

    The dynamic binding capacity (DBC) and its dependence on residence time influence the design and productivity of adsorption columns used in protein capture applications. This paper offers a very simple approach to predict the DBC of an adsorption column based on a measurement of the equilibrium binding capacity (EBC) and of the time needed to achieve one-half of the EBC in a batch adsorption test. The approach is based on a mass transfer kinetics model that assumes pore diffusion with a rectangular isotherm; however, the same approach is also shown to work for other systems where solute transport inside the particle occurs through other transport mechanisms.

  9. Alkali cation specific adsorption onto fcc(111) transition metal electrodes.

    PubMed

    Mills, J N; McCrum, I T; Janik, M J

    2014-07-21

    The presence of alkali cations in electrolyte solutions is known to impact the rate of electrocatalytic reactions, though the mechanism of such impact is not conclusively determined. We use density functional theory (DFT) to examine the specific adsorption of alkali cations to fcc(111) electrode surfaces, as specific adsorption may block catalyst sites or otherwise impact surface catalytic chemistry. Solvation of the cation-metal surface structure was investigated using explicit water models. Computed equilibrium potentials for alkali cation adsorption suggest that alkali and alkaline earth cations will specifically adsorb onto Pt(111) and Pd(111) surfaces in the potential range of hydrogen oxidation and hydrogen evolution catalysis in alkaline solutions.

  10. Competitive adsorption of organic compounds by microbial biomass

    SciTech Connect

    Selvakumar, A.; Hsieh, H.N. )

    1988-01-01

    This study investigated the effect of competitive adsorption of liquid organic compounds on inactive microbial biomass in bisolute solution systems. Phenol-nitrophenol, phenol-chlorophenol, nitrophenol-chlorophenol, and chlorobenzene-ethylbenzene systems were selected for the analysis. The experimental results suggest that although the amount of each solute adsorbed on the biomass can be reduced significantly by the presence of a second solute, the combined adsorptive capacity was greater than that for either of the individual substances from its pure solution. The octanol/water partition coefficient(K{sub ow}) indicates the relative extent of adsorption better than the aqueous solubility(S).

  11. An assay for measurement of protein adsorption to glass vials.

    PubMed

    Varmette, Elizabeth; Strony, Brianne; Haines, Daniel; Redkar, Rajendra

    2010-01-01

    Protein adsorption to primary packaging is one of the problems faced by biopharmaceutical drug companies. An assay was developed to quantify loss of proteins to glass vial surfaces. The assay involves the labeling of protein with a fluorescent dye, incubation of the labeled protein with the vial surface, elution of the adsorbed protein using a stripping buffer, and determination of fluorescence of the adsorbed protein using a fluorometer. The assay is simple to set up, accurate, sensitive, and flexible. The assay can be modified for indirect measurement of protein adsorption and offers an attractive alternative for researchers to quantify protein adsorption to glass vials and syringes.

  12. Preparative chromatography of xylanase using expanded bed adsorption.

    PubMed

    Silvino, DosSantosEveraldo; Guirardello, Reginaldo; Teixeira, Franco Telma

    2002-01-25

    Expanded bed adsorption was used to purify a marketable xylanase often used in the kraft pulp bleaching process. Experiments in packed and expanded beds were carried out mainly to study the adsorption of xylanase on to a cationic adsorbent (Streamline SP) in the presence of cells. In order to study the presence of cells, a Bacillus pumilus mass (5% wet mass) was mixed with the enzyme extract and submitted to an expanded bed adsorption system. One xylanase was purified to homogeneity in the packed bed. However, the 5% cell content hampered purification.

  13. Adsorption of reactive dyes on to carbonate substituted nanohydroxyapatite

    NASA Astrophysics Data System (ADS)

    Vasugi, G.; Kumar, G. Suresh; Girija, E. K.

    2014-04-01

    Carbonate substituted nanohydroxyapatite (CHA) was synthesized and utilized for the removal of reactive red and reactive blue dye from aqueous solution, as it mimics the composition of conventional adsorbent animal bone charcoal. Also ionic substitution seems to alter the surface nature of the apatite structure. Physicochemical nature of adsorbent was characterized by XRD, FT-IR and SEM analysis. Adsorption as a function of contact time, adsorbent dosage and pH were studied by batch mode adsorption technique. Kinetic studies were performed to correlate the experimental kinetic data with theoretical models in order to understand the adsorption mechanism and the reaction rate.

  14. Adsorption Kinetics in Micellar Solutions of Nonionic Surfactants

    NASA Astrophysics Data System (ADS)

    Colegate, Daniel M.; Bain, Colin D.

    2005-11-01

    Standard models of the adsorption kinetics of surfactants at the air-water surface assume that micelles break down into monomers in the bulk solution and that only monomers adsorb. We show here that micelles of the nonionic surfactant C14E8 adsorb to the surface of a liquid jet at a diffusion-controlled rate. Micellar adsorption can be switched off by incorporation of a small amount of ionic surfactant into the micelle and switched on again by addition of salt. More sophisticated models of adsorption processes in micellar solutions are required that permit a kinetic flux of micelles to the air-water interface.

  15. Adsorption of arsenic from water and its recovery as a highly active photocatalyst.

    PubMed

    Hott, Rodrigo C; Andrade, Thaina G; Santos, Mayra S; Lima, Anne C F; Faria, Márcia C S; Bomfeti, Cleide A; Barbosa, Fernando; Maia, Luiz F O; Oliveira, Luiz C A; Pereira, Márcio C; Rodrigues, Jairo L

    2016-11-01

    The contamination of water with arsenic has aroused concern around the world due to its toxic effects. Thus, the development of low-cost technologies for treating water contaminated with toxic metals is highly advisable. Adsorption is an attractive technology for purification of contaminated water, but it only transfers the contaminant from water to the solid adsorbent, which provokes another problem related to solid residue disposal. In this work, we developed a sustainable method for purifying water contaminated with arsenic by using δ-FeOOH nanoparticles. The adsorption capacities of nanomaterial for As(3+) and As(5+) species were 40 and 41 mg g(-1), respectively, and were highly efficient to purify arsenic-contaminated water from a Brazilian river. The concentration of arsenic in water was close to zero after the water treatment by δ-FeOOH. Once the arsenic is adsorbed, it can be recovered by treatment with NaOH solutions. Approximately 85 % of the total adsorbed arsenic could be recovered and used as a precursor to produce useful material (Ag3AsO4) with excellent photocatalytic activity. It was active under visible light and had a high recyclability for oxidation of rhodamine B. Finally, the simple method described is promising to design sustainable process of environmental remediation with minimum residue generation.

  16. CHP Technologies

    EPA Pesticide Factsheets

    Learn about CHP technologies, including reciprocating engines, combustion turbines, steam turbines, microturbines, fuel cells, and waste heat to power. Access the Catalog of CHP Technologies and the Biomass CHP Catalog of Technologies.

  17. Comparative evaluation of adsorption kinetics of diclofenac and isoproturon by activated carbon.

    PubMed

    Torrellas, Silvia A; Rodriguez, Araceli R; Escudero, Gabriel O; Martín, José María G; Rodriguez, Juan G

    2015-01-01

    Adsorption mechanism of diclofenac and isoproturon onto activated carbon has been proposed using Langmuir and Freundlich isotherms. Adsorption capacity and optimum adsorption isotherms were predicted by nonlinear regression method. Different kinetic equations, pseudo-first-order, pseudo-second-order, intraparticle diffusion model and Bangham kinetic model, were applied to study the adsorption kinetics of emerging contaminants on activated carbon in two aqueous matrices.

  18. [Adsorption kinetics and mechanism of lead (II) on polyamine-functionalized mesoporous activated carbon].

    PubMed

    Li, Kun-Quan; Wang, Yan-Jin; Yang, Mei-Rong; Zhu, Zhi-Qiang; Zheng, Zheng

    2014-08-01

    Bagasse mesoporous carbon was prepared by microwave assisted H3 PO4 activation. Amido and imido groups were modified with ethanediamine on the channels' surface of mesoporous carbon through nitric oxidation and amide reaction. The influence of Pb(II) concentration, adsorption time on Pb(II) adsorption on the ethanediamine-modified mesoporous carbon (AC-EDA) was investigated. The adsorption kinetics and mechanism were also discussed. The results showed that AC-EDA had a great performance for Pb(II) adsorption, and more than 70% of Pb(II) was adsorbed in 5 minutes. The adsorption amount of Pb(II) on the carbon increased with the increase of solution pH in acidic conditions. It was found that AC-EDA had different binding energies on different adsorption sites for Pb(II) separation. The Pb(II) adsorption process on AC-EDA was controlled by intra-particle diffusion in the first 3 min, and then film diffusion played the important pole on the adsorption. The adsorption amount increased with the increase of temperature, indicating the adsorption was an endothermic reaction. The high adsorption energy (> 11 kJ x mol(-1)) implied that the) adsorption was a chemical adsorption. The XPS of AC-EDA before and after Pb(II) adsorption showed that the polyamine group was involved in the adsorption, and should be a main factor of the high efficient adsorption.

  19. The National Shipbuilding Research Program. Document Technologies Available to Clean Brackish Waters to 50 PPT TBT Levels

    DTIC Science & Technology

    1997-12-01

    technology such as Dissolved Air Floatation, and Activated Carbon adsorption are the best candidate technologies. 3. While there are accepted and practical...nitrogen- or ester-containing ashless dispersant and (B) a bis-keto/thioketo compound. 57 5653883: Stirred Tank Biological Activated Carbon Adsorption ... Carbon Effluent treatment using activated carbon has been found to remove a wide range of organic pollutants from water. A search using key words

  20. Dimension Technologies

    NASA Video Gallery

    Command and Control Technologies (CCT) Corporation of Titusville, Florida, a Florida/NASA Business Incubator tenant, is commercializing technology based on Kennedy Space Center's (KSC's) spacecraft...