Science.gov

Sample records for adsorption reached equilibrium

  1. Arsenic Adsorption Equilibrium Concentration and Adsorption Rate of Activated Carbon Coated with Ferric-Aluminum Hydroxides

    NASA Astrophysics Data System (ADS)

    Zhang, M.; Sugita, H.; Oguma, T.; Hara, J.; Takahashi, S.

    2015-12-01

    In some areas of developing countries, ground or well water contaminated with arsenic has been reluctantly used as drinking water. It is highly desirable that effective and inexpensive arsenic removal agents should be developed and provided to reduce the potential health risk. Previous studies demonstrated that activated carbon coated with ferric-aluminum hydroxides (Fe-Al-C) has high adsorptive potential for removal of arsenic. In this study, a series of experiments using Fe-Al-C were carried to discuss adsorption equilibrium time, adsorption equilibrium concentration and adsorption rate of arsenic for Fe-Al-C. Fe-Al-C used in this study was provided by Astec Co., Ltd. Powder reagent of disodium hydrogen arsenate heptahydrate was dissolved into ion-exchanged water. The solution was then further diluted with ion-exchanged water to be 1 and 10 mg/L as arsenic concentration. The pH of the solution was adjusted to be around 7 by adding HCl and/or NaOH. The solution was used as artificial arsenic contaminated water in two types of experiments (arsenic adsorption equilibrium and arsenic adsorption rate tests). The results of the arsenic equilibrium tests were showed that a time period of about 3 days to reach apparent adsorption equilibrium for arsenic. The apparent adsorption equilibrium concentration and adsorbed amount of arsenic on Fe-Al-C adsorbent could be estimated by application of various adsorption isotherms, but the distribution coefficient of arsenic between solid and liquid varies with experimental conditions such as initial concentration of arsenic and addition concentration of adsorbent. An adsorption rate equation that takes into account the reduction in the number of effective adsorption sites on the adsorbent caused by the arsenic adsorption reaction was derived based on the data obtained from the arsenic adsorption rate tests.

  2. Development of facile property calculation model for adsorption chillers based on equilibrium adsorption cycle

    NASA Astrophysics Data System (ADS)

    Yano, Masato; Hirose, Kenji; Yoshikawa, Minoru; Thermal management technology Team

    Facile property calculation model for adsorption chillers was developed based on equilibrium adsorption cycles. Adsorption chillers are one of promising systems that can use heat energy efficiently because adsorption chillers can generate cooling energy using relatively low temperature heat energy. Properties of adsorption chillers are determined by heat source temperatures, adsorption/desorption properties of adsorbent, and kinetics such as heat transfer rate and adsorption/desorption rate etc. In our model, dependence of adsorption chiller properties on heat source temperatures was represented using approximated equilibrium adsorption cycles instead of solving conventional time-dependent differential equations for temperature changes. In addition to equilibrium cycle calculations, we calculated time constants for temperature changes as functions of heat source temperatures, which represent differences between equilibrium cycles and real cycles that stemmed from kinetic adsorption processes. We found that the present approximated equilibrium model could calculate properties of adsorption chillers (driving energies, cooling energies, and COP etc.) under various driving conditions quickly and accurately within average errors of 6% compared to experimental data.

  3. Finding balance: Virus populations reach equilibrium during the infection process.

    PubMed

    Harper, S J; Cowell, S J; Dawson, W O

    2015-11-01

    Virus populations, mixtures of viral strains or species, are a common feature of viral infection, and influence many viral processes including infection, transmission, and the induction of disease. Yet, little is known of the rules that define the composition and structure of these populations. In this study, we used three distinct strains of Citrus tristeza virus (CTV) to examine the effect of inoculum composition, titer, and order, on the virus population. We found that CTV populations stabilized at the same equilibrium irrespective of how that population was introduced into a host. In addition, both field and experimental observations showed that these equilibria were relatively uniform between individual hosts of the same species and under the same conditions. We observed that the structure of the equilibria reached is determined primarily by the host, with the same inoculum reaching different equilibria in different species, and by the fitness of individual virus variants. PMID:26291064

  4. Equilibrium, kinetic and thermodynamic studies on the adsorption of phenol onto graphene

    SciTech Connect

    Li, Yanhui; Du, Qiuju; Liu, Tonghao; Sun, Jiankun; Jiao, Yuqin; Xia, Yanzhi; Xia, Linhua; Wang, Zonghua; Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai

    2012-08-15

    Graphical abstract: The effect of temperature on phenol adsorbed by graphene shows that the equilibrium adsorption capacity of phenol increases with the increase in temperature from 285 to 333 K. Increasing adsorption capacities with temperature indicates that the adsorption of phenol is controlled by an endothermic reaction. Highlights: ► The graphene has high phenol adsorption capacity. ► The graphene has a high specific surface area of 305 m{sup 2}/g. ► The adsorption capacity is high at acidic pH range. ► The graphene has rapid phenol adsorption rate. ► Phenol adsorption is a spontaneous and endothermic process. -- Abstract: Graphene, a new member of carbon family, has been prepared, characterized and used as adsorbent to remove phenol from aqueous solution. The effect parameters including pH, dosage, contact time, and temperature on the adsorption properties of phenol onto graphene were investigated. The results showed that the maximum adsorption capacity can reach 28.26 mg/g at the conditions of initial phenol concentration of 50 mg/L, pH 6.3 and 285 K. Adsorption data were well described by both Freundlich and Langmuir models. The kinetic study illustrated that the adsorption of phenol onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of phenol onto graphene was endothermic and spontaneous.

  5. Adsorption characteristics of siloxanes in landfill gas by the adsorption equilibrium test

    SciTech Connect

    Nam, Sangchul; Namkoong, Wan; Kang, Jeong-Hee; Park, Jin-Kyu; Lee, Namhoon

    2013-10-15

    Highlights: • Equilibrium test was attempted to evaluate adsorption characteristics of siloxane. • L2 had higher removal efficiency in carbon compared to noncarbon adsorbents. • Total adsorption capacity of siloxane was 300 mg/g by coal activated carbon. • Adsorption characteristics rely on size of siloxane molecule and adsorbent pore. • Conversion of siloxane was caused by adsorption of noncarbon adsorbents. - Abstract: Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane.

  6. Adsorption equilibrium and kinetics of monomer-dimer monoclonal antibody mixtures on a cation exchange resin.

    PubMed

    Reck, Jason M; Pabst, Timothy M; Hunter, Alan K; Wang, Xiangyang; Carta, Giorgio

    2015-07-10

    Adsorption equilibrium and kinetics are determined for a monoclonal antibody (mAb) monomer and dimer species, individually and in mixtures, on a macroporous cation exchange resin both under the dilute limit of salt gradient elution chromatography and at high protein loads and low salt based on batch adsorption equilibrium and confocal laser scanning microscopy (CLSM) experiments. In the dilute limit and weak binding conditions, the dimer/monomer selectivity in 10mM phosphate at pH 7 varies between 8.7 and 2.3 decreasing with salt concentration in the range of 170-230mM NaCl. At high protein loads and strong binding conditions (0-60mM NaCl), the selectivity in the same buffer is near unity with no NaCl added, but increases gradually with salt concentration reaching high values between 2 and 15 with 60mM added NaCl. For these conditions, the two-component adsorption kinetics is controlled by pore diffusion and is predicted approximately by a dual shrinking core model using parameters based on single component equilibrium and kinetics measurements. PMID:26028510

  7. [Characterization of Cr (VI) removal and total Cr equilibrium adsorption by sulfate reducing granular sludge in stimulant wastewater].

    PubMed

    Luo, Jun; Pang, Zhi-Hua; Hu, Yong-You; Zhong, Hai-Tao; Chen, Jian-Yu; Lin, Fang-Min

    2010-11-01

    Sulfate reducing granular sludge (SRGS) cultivated in small scale EGSB reactor was used for Cr (VI) removing. Characterization of Cr (VI) removal and total Cr equilibrium adsorption was studied, and the adsorption isotherm was fitted. Results showed that removal of Cr (VI) was in connection with the structure and chemical composition of SRGS and several environmental factors. The Cr (VI) removal rate increased with the dosage of granular sludge; the increasing of oscillation speed and temperature could enhance Cr (VI) removal and total Cr adsorption, but while the oscillation speed reached 150 r x min(-1) or the temperature came to 40 degrees C, the physical structure of granular sludge would be affected and the granular sludge discrete, and total Cr equilibrium adsorption decreased; lower pH value caused higher Cr (VI) removal rate, however the sulfate on the surface of granular sludge was affected by lower pH value easily and would translate into H2S, then total Cr adsorption rate decreased. Cr (VI) removal would be influenced by physical, chemical and biological factors, and the process included reduction and adsorption mainly. The maximum adsorption of total Cr by granular sludge was 6.84 mg x g(-1), and the total Cr adsorbing process fitted in with Langmuir adsorption isotherm. PMID:21250453

  8. Adsorption Properties of Tetracycline onto Graphene Oxide: Equilibrium, Kinetic and Thermodynamic Studies

    PubMed Central

    Ghadim, Ehsan Ezzatpour; Manouchehri, Firouzeh; Soleimani, Gholamreza; Hosseini, Hadi; Kimiagar, Salimeh; Nafisi, Shohreh

    2013-01-01

    Graphene oxide (GO) nanoparticle is a high potential effective absorbent. Tetracycline (TC) is a broad-spectrum antibiotic produced, indicated for use against many bacterial infections. In the present research, a systematic study of the adsorption and release process of tetracycline on GO was performed by varying pH, sorption time and temperature. The results of our studies showed that tetracycline strongly loads on the GO surface via π–π interaction and cation–π bonding. Investigation of TC adsorption kinetics showed that the equilibrium was reached within 15 min following the pseudo-second-order model with observed rate constants of k2 = 0.2742–0.5362 g/mg min (at different temperatures). The sorption data has interpreted by the Langmuir model with the maximum adsorption of 323 mg/g (298 K). The mean energy of adsorption was determined 1.83 kJ/mol (298 K) based on the Dubinin–Radushkevich (D–R) adsorption isotherm. Moreover, the thermodynamic parameters such as ΔH°, ΔS° and ΔG° values for the adsorption were estimated which indicated the endothermic and spontaneous nature of the sorption process. The electrochemistry approved an ideal reaction for the adsorption under electrodic process. Simulation of GO and TC was done by LAMMPS. Force studies in z direction showed that tetracycline comes close to GO sheet by C8 direction. Then it goes far and turns and again comes close from amine group to the GO sheet. PMID:24302989

  9. Physical Adsorption of Gases on Heterogeneous Solids and Equilibrium Studies of the Pressure Swing Adsorption Process.

    NASA Astrophysics Data System (ADS)

    Lu, Xiaochun

    1990-01-01

    -parameter isotherm equation based on benzene adsorption isotherms. We extended further the TVFM to derive thermodynamic functions, such as the adsorption entropy, the adsorption enthalpy, and the adsorption energy distribution, and constructed these functions for various adsorption systems based on their adsorption isotherms. To explore the energetic heterogeneity of the adsorbent, we used two approaches. First, we used the overall integral isotherm equation to obtain the Langmuir -Freundlich isotherm; and second, we used the Gibb's relation to obtain an exponential isotherm equation. The adsorption energy-distribution function can be obtained from these isotherm equations. The pressure swing adsorption (PSA) process was studied based on Shandalman and Mitchell's equilibrium theory for a PSA system with a linear isotherm. This theory was extended to a PSA system with a non-linear isotherm. Relationships were established between the isotherms and process parameters, such as the enrichment factor, the critical recycle ratio, and the extent of the recovery.

  10. On the fractality of the Freundlich adsorption isotherm in equilibrium and non-equilibrium cases.

    PubMed

    Borys, Przemysław; Grzywna, Zbigniew J

    2016-07-27

    We investigate the relationship between the Freundlich adsorption exponent and the fractal dimension of the adsorption sites for quasi-monolayer adsorption, and of the adsorbed aggregate for a simple case of multilayer adsorption. We further check whether the Freundlich adsorption mechanism may contribute to anomalous diffusion in the transport through porous materials. PMID:27414951

  11. On the time needed to reach an equilibrium structure of the radiation belts

    DOE PAGESBeta

    Ripoll, J. -F.; Loran, V.; Cunningham, Gregory Scott; Reeves, Geoffrey D.; Shprits, Y. Y.

    2016-06-04

    In this paper, we complement the notion of equilibrium states of the radiation belts with a discussion on the dynamics and time needed to reach equilibrium. We solve for the equilibrium states obtained using 1D radial diffusion with recently developed hiss and chorus lifetimes at constant values of Kp = 1, 3 and 6. We find that the equilibrium states at moderately low Kp, when plotted vs L-shell (L) and energy (E), display the same interesting S-shape for the inner edge of the outer belt as recently observed by the Van Allen Probes. The S-shape is also produced as themore » radiation belts dynamically evolve toward the equilibrium state when initialized to simulate the buildup after a massive dropout or to simulate loss due to outward diffusion from a saturated state. Physically, this shape, intimately linked with the slot structure, is due to the dependence of electron loss rate (originating from wave-particle interactions) on both energy and L-shell. Equilibrium electron flux profiles are governed by the Biot number (τDiffusion/τloss), with large Biot number corresponding to low fluxes and low Biot number to large fluxes. The time it takes for the flux at a specific (L, E) to reach the value associated with the equilibrium state, starting from these different initial states, is governed by the initial state of the belts, the property of the dynamics (diffusion coefficients), and the size of the domain of computation. Its structure shows a rather complex scissor form in the (L, E) plane. The equilibrium value (phase space density or flux) is practically reachable only for selected regions in (L, E) and geomagnetic activity. Convergence to equilibrium requires hundreds of days in the inner belt for E > 300 keV and moderate Kp (≤3). It takes less time to reach equilibrium during disturbed geomagnetic conditions (Kp ≥ 3), when the system evolves faster. Restricting our interest to the slot region, below L = 4, we find that only small regions in (L, E) space

  12. Adsorption of cadmium from aqueous solution onto untreated coffee grounds: equilibrium, kinetics and thermodynamics.

    PubMed

    Azouaou, N; Sadaoui, Z; Djaafri, A; Mokaddem, H

    2010-12-15

    Adsorption can be used as a cost effective and efficient technique for the removal of toxic heavy metals from wastewater. Waste materials with no further treatment such as coffee grounds from cafeterias may act as adsorbents for the removal of cadmium. Batch kinetic and equilibrium experiments were conducted to study the effects of contact time, adsorbent dose, initial pH, particle size, initial concentration of cadmium and temperature. Three adsorption isotherm models namely, Langmuir, Freundlich and Dubinin-Radushkevich were used to analyse the equilibrium data. The Langmuir isotherm which provided the best correlation for Cd(2+) adsorption onto coffee grounds, shows that the adsorption was favourable and the adsorption capacity found was equal to 15.65 mg g(-1). Thermodynamic parameters were evaluated and the adsorption was exothermic. The equilibrium was achieved less than 120 min. The adsorption kinetic data was fitted with first and second order kinetic models. Finally it was concluded that the cadmium adsorption kinetic onto coffee grounds was well fitted by second order kinetic model rather than first order model. The results suggest that coffee grounds have high possibility to be used as effective and economical adsorbent for Cd(2+) removal. PMID:20817346

  13. Adsorption of leather dye onto activated carbon prepared from bottle gourd: equilibrium, kinetic and mechanism studies.

    PubMed

    Foletto, Edson Luiz; Weber, Caroline Trevisan; Paz, Diego Silva; Mazutti, Marcio Antonio; Meili, Lucas; Bassaco, Mariana Moro; Collazzo, Gabriela Carvalho

    2013-01-01

    Activated carbon prepared from bottle gourd has been used as adsorbent for removal of leather dye (Direct Black 38) from aqueous solution. The activated carbon obtained showed a mesoporous texture, with surface area of 556.16 m(2) g(-1), and a surface free of organic functional groups. The initial dye concentration, contact time and pH significantly influenced the adsorption capacity. In the acid region (pH 2.5) the adsorption of dye was more favorable. The adsorption equilibrium was attained after 60 min. Equilibrium data were analyzed by the Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. The equilibrium data were best described by the Langmuir isotherm, with maximum adsorption capacity of 94.9 mg g(-1). Adsorption kinetic data were fitted using the pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The adsorption kinetic was best described by the second-order kinetic equation. The adsorption process was controlled by both external mass transfer and intraparticle diffusion. Activated carbon prepared from bottle gourd was shown to be a promising material for adsorption of Direct Black 38 from aqueous solution. PMID:23128640

  14. Do persistent organic pollutants reach a thermodynamic equilibrium in the global environment?

    PubMed

    Schenker, Sebastian; Scheringer, Martin; Hungerbühler, Konrad

    2014-05-01

    Equilibrium partitioning between different environmental media is one of the main driving forces that govern the environmental fate of organic chemicals. In the global environment, equilibrium partitioning is in competition with long-range transport, advective phase transfer processes such as wet deposition, and degradation. Here we investigate under what conditions equilibrium partitioning is strong enough to control the global distribution of organic chemicals. We use a global multimedia mass-balance model to calculate the Globally Balanced State (GBS) of organic chemicals. The GBS is the state where equilibrium partitioning is in balance with long-range transport; it represents the maximum influence of thermodynamic driving forces on the global distribution of a chemical. Next, we compare the GBS with the Temporal Remote State, which represents the long-term distribution of a chemical in the global environment when the chemical's distribution is influenced by all transport and degradation processes in combination. This comparison allows us to identify the chemical properties required for a substance to reach the GBS as a stable global distribution. We find that thermodynamically controlled distributions are rare and do not occur for most Persistent Organic Pollutants. They are only found for highly volatile and persistent substances, such as chlorofluorocarbons. Furthermore, we find that the thermodynamic cold-trap effect (i.e., accumulation of pollutants at the poles because of reduced vapor pressure at low temperatures) is often strongly attenuated by atmospheric and oceanic long-range transport. PMID:24654605

  15. Adsorption of Rhodamine B on two novel polar-modified post-cross-linked resins: Equilibrium and kinetics.

    PubMed

    Jiang, Xiangfu; Huang, Jianhan

    2016-04-01

    We employed two polar monomers, triallyl isocyanurate (TAIC) and butyl acrylate (BA), to copolymerize with divinylbenzene (DVB), and synthesized two starting copolymers labeled PDT and PDB. Then, the Friedel-Crafts alkylation reaction was performed for the two starting copolymers, and the residual pendent vinyl groups were consumed, and hence we obtained two novel polar-modified post-cross-linked resins PDTpc and PDBpc. The surface polarity greatly improved due to introduction of the polar monomers, and the Brunauer-Emmett-Teller (BET) surface area and pore volume significantly increased after the Friedel-Crafts alkylation reaction. Compared with the starting copolymers, the non-polar post-cross-linked resin PDVBpc and some other adsorbents in the references, PDTpc and PDBpc possessed a much enhanced adsorption to Rhodamine B, and the equilibrium capacity reached 578.2mg/g and 328.7mg/g, respectively, at an equilibrium concentration of 100mg/L, and the Freundlich model characterized the equilibrium data very well. The adsorption was a fast process and the kinetic data obeyed the micropore diffusion model. These results confirmed that PDTpc and PDBpc had the potential superiority in adsorptive removal of Rhodamine B from aqueous solution. PMID:26803602

  16. Equilibrium adsorption and self-assembly of patchy colloids in microchannels

    NASA Astrophysics Data System (ADS)

    Marshall, Bennett D.

    2016-07-01

    A theory is developed to describe the equilibrium adsorption and self-assembly of patchy colloids in microchannels. The adsorption theory is developed in classical density functional theory, with the adsorbed phase and fluid phase chemical potentials modeled using thermodynamic perturbation theory. Adsorption of nonpatchy colloids in microchannels is typically achieved through nonequilibrium routes such as spin coating and evaporation. These methods are required due to the entropic penalty of adsorption. In this work we propose that the introduction of patches on the colloids greatly enhances the temperature dependent and reversible adsorption of colloids in microchannels. It is shown how bulk fluid density, temperature, patch size, and channel diameter can be manipulated to achieve the adsorption and self-assembly of patchy colloids in microchannels.

  17. Equilibrium adsorption and self-assembly of patchy colloids in microchannels.

    PubMed

    Marshall, Bennett D

    2016-07-01

    A theory is developed to describe the equilibrium adsorption and self-assembly of patchy colloids in microchannels. The adsorption theory is developed in classical density functional theory, with the adsorbed phase and fluid phase chemical potentials modeled using thermodynamic perturbation theory. Adsorption of nonpatchy colloids in microchannels is typically achieved through nonequilibrium routes such as spin coating and evaporation. These methods are required due to the entropic penalty of adsorption. In this work we propose that the introduction of patches on the colloids greatly enhances the temperature dependent and reversible adsorption of colloids in microchannels. It is shown how bulk fluid density, temperature, patch size, and channel diameter can be manipulated to achieve the adsorption and self-assembly of patchy colloids in microchannels. PMID:27575187

  18. Equilibrium study of single-solute adsorption of anionic surfactants with polymeric XAD resins

    SciTech Connect

    Garcia-Delgado, R.A.; Cotoruelo-Minguez, L.M.; Rodriguez, J.J. )

    1992-06-01

    Equilibrium data for the adsorption of sodium lauryl sulfate (SLS) and sodium dodecylbenzene sulfonate (SDBS) from aqueous solutions by Amberlite XAD-4 and XAD-7 polymeric resins at temperatures in the 10-40C range have been obtained. The specific surface area of the resins plays a major role in adsorption, and thus the best results have been obtained with XAD-4 resin. A higher adsorption of SDBS over SLS was also observed. Several adsorption isotherm models have been used to fit the experimental data. The best results have been obtained with the Redlich-Peterson and Langmuir-Freundlich equations. Estimations of the isosteric heat of adsorption, free energy, and entropy of adsorption are also reported.

  19. Equilibrium studies of copper ion adsorption onto palm kernel fibre.

    PubMed

    Ofomaja, Augustine E

    2010-07-01

    The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin-Radushkevich (D-R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r(2), and the non-linear Chi-square, chi(2) error analysis. The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH(PZC) of the palm kernel fibre with an optimum dose of 10g/dm(3). The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 x 10(-4)mol/g at 339K. The sorption equilibrium constant, K(a), increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B(1), with increasing temperature. The Dubinin-Radushkevich (D-R) isotherm parameter, free energy, E, was in the range of 15.7-16.7kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO(3) and CH(3)COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic. PMID:20346574

  20. Equilibrium, kinetic and thermodynamic study of cesium adsorption onto nanocrystalline mordenite from high-salt solution.

    PubMed

    Lee, Keun-Young; Park, Minsung; Kim, Jimin; Oh, Maengkyo; Lee, Eil-Hee; Kim, Kwang-Wook; Chung, Dong-Yong; Moon, Jei-Kwon

    2016-05-01

    In this study, the equilibrium, kinetics and thermodynamics of cesium adsorption by nanocrystalline mordenite were investigated under cesium contamination with high-salt solution, simulating the case of an operation and decommissioning of nuclear facilities or an accident during the processes. The adsorption rate constants were determined using a pseudo second-order kinetic model. The kinetic results strongly demonstrated that the cesium adsorption rate of nano mordenite is extremely fast, even in a high-salt solution, and much faster than that of micro mordenite. In the equilibrium study, the Langmuir isotherm model fit the cesium adsorption data of nano mordenite better than the Freundlich model, which suggests that cesium adsorption onto nano mordenite is a monolayer homogeneous adsorption process. The obtained thermodynamic parameters indicated that the adsorption involved a very stable chemical reaction. In particular, the combination of rapid particle dispersion and rapid cesium adsorption of the nano mordenite in the solution resulted in a rapid and effective process for cesium removal without stirring, which may offer great advantages for low energy consumption and simple operation. PMID:26683820

  1. Effect of the adsorbate (Bromacil) equilibrium concentration in water on its adsorption on powdered activated carbon. Part 1. Equilibrium parameters.

    PubMed

    Al Mardini, Fadi; Legube, Bernard

    2009-10-30

    This study was carried out to investigate the adsorption equilibrium and kinetics of a pesticide of the uracil group on powdered activated carbon (PAC). The experiments were conducted at a wide range of initial pesticide concentrations (approximately 5 microg L(-1) to approximately 500 microg L(-1) at pH 7.8), corresponding to equilibrium concentrations of less than 0.1 microg L(-1) for the weakest, which is compatible with the tolerance limits of drinking water. Such a very broad range of initial solute concentrations resulting powdered activated carbon (PAC) concentrations (0.1-5 mg L(-1)) is the main particularity of our study. The application of several monosolute equilibrium models (two, three or more parameters) has generally shown that Bromacil adsorption is probably effective on two types of sites. High reactivity sites (K(L) approximately 10(3) Lmg(-1)) which are 10-20 less present in a carbon surface than lower reactivity sites (K(L) approximately 10 Lmg(-1)), according to the q(m) values calculated by two- or three-parameter models. The maximum capacity of the studied powdered activated carbon (PAC), corresponding to monolayer adsorption, compared to the Bromacil molecule surface, would be between 170 mg g(-1) and 190 mg g(-1). This theoretical value is very close to the experimental q(m) values obtained when using linearized forms of Langmuir, Tóth and Fritz-Schluender models. PMID:19539425

  2. Adsorptive removal of heavy metals by magnetic nanoadsorbent: an equilibrium and thermodynamic study

    NASA Astrophysics Data System (ADS)

    Shirsath, D. S.; Shirivastava, V. S.

    2015-11-01

    An efficient and new magnetic nanoadsorbent photocatalyst was fabricated by co-precipitation technique. This research focuses on understanding metal removal process and developing a cost-effective technology for treatment of heavy metal-contaminated industrial wastewater. In this investigation, magnetic nanoadsorbent has been employed for the removal of Zn(II) ions from aqueous solutions by a batch adsorption technique. The adsorption equilibrium data fitted very well to Langmuir and Freundlich adsorption isotherm models. The thermodynamics of Zn(II) ions adsorption onto the magnetic nanoadsorbents indicated that the adsorption was spontaneous, endothermic and physical in nature. Surface morphology of magnetic nanoadsorbent by scanning electron microscopy (SEM) and elemental analysis by EDX technique. The structural and photocatalytic properties of magnetic nanoadsorbent were characterized using X-ray diffraction (XRD) and FTIR techniques. Also, the magnetic properties of synthesized magnetic nanoadsorbent were determined by vibrating spinning magnetometer (VSM).

  3. Equilibrium and kinetic data and process design for adsorption of Congo Red onto bentonite.

    PubMed

    Bulut, Emrah; Ozacar, Mahmut; Sengil, I Ayhan

    2008-06-15

    The adsorption of Congo Red onto bentonite in a batch adsorber has been studied. Four kinetic models, the pseudo first- and second-order equations, the Elovich equation and the intraparticle diffusion equation, were selected to follow the adsorption process. Kinetic parameters; rate constants, equilibrium adsorption capacities and correlation coefficients, for each kinetic equation were calculated and discussed. It was shown that the adsorption of Congo Red onto bentonite could be described by the pseudo second-order equation. The experimental isotherm data were analyzed using the Langmuir, Freundlich and Temkin equations. Adsorption of Congo Red onto bentonite followed the Langmuir isotherm. A single stage batch adsorber was designed for different adsorbent mass/treated effluent volume ratios using the Langmuir isotherm. PMID:18055111

  4. Equilibrium and Kinetic Adsorption of Bacteria on Alluvial Sand and Surface Thermodynamic Interpretation

    SciTech Connect

    Chen, Gang; Rockhold, Mark L.; Strevett, Keith A.

    2003-05-15

    Equilibrium and kinetic adsorption of Escherichia coli HB 101, E. coli JM 109, Pseudomonas fluorescens, Pseudomonas putida and Pseudomonas sp. on alluvial sand from the Canadian River alluvium (Norman, OK) was investigated through column experiments. Equilibrium adsorption of these five bacterial strains followed the Freundlich expression and was a function of zero energy points, an indication of the zero energy buffer zone. Among the microorganisms studied, P. putida had the greatest equilibrium adsorption (162.4 x 108 cell/g sediment with a microbial injectate concentration of 108 cell/mL), followed by Pseudomonas sp. (127.9 x 108 cell/g sediment), E. coli HB 101 (62.8 x 108 cell/g sediment), E. coli JM 109 (58.4 x 108 cell/g sediment), and P. fluorescens (42.6 x 108 cell/g sediment). The first-order kinetic adsorption rate coefficient was an exponential function of the total interaction free energy between bacteria and sediment evaluated at the primary minimum, (PM). E. coli HB 101 had the greatest kinetic adsorption rate coefficient on the sediment (5.10 h-1), followed by E. coli JM 109 (4.52 h-1), P. fluorescens (2.12 h-1), P. putida (2.04 h-1), and Pseudomonas sp. (1.34 h-1).

  5. Binary adsorption equilibrium of carbon dioxide and water vapor on activated alumina.

    PubMed

    Li, Gang; Xiao, Penny; Webley, Paul

    2009-09-15

    Adsorption equilibria of a CO2/H2O binary mixture on activated alumina F-200 were measured at several temperatures and over a wide range of concentrations from 4% to around 90% of the saturated water vapor pressure. In comparison with the single-component data, the loading of CO2 was not reduced in the presence of H2O, whereas at low relative humidity the adsorption of H2O was depressed. The binary system was described by a competitive/cooperative adsorption model where the readily adsorbed water layers acted as secondary sites for further CO2 adsorption via hydrogen bonding or hydration reaction. The combination of kinetic models, namely, a Langmuir isotherm for characterizing pure CO2 adsorption and a BET isotherm for H2O, was extended to derive a binary adsorption equilibrium model for the CO2/H2O mixture. Models based on the ideal adsorbed solution theory of Myers and Prausnitz failed to characterize the data over the whole composition range, and a large deviation of binary CO2/H2O equilibrium from ideal solution behavior was observed. The extended Langmuir-BET (LBET) isotherm, analogous to the extended Langmuir equation, drastically underestimated the CO2 loading. By incorporating the interactions between CO2 and H2O molecules on the adsorbent surface and taking into account the effect of nonideality, the realistic interactive LBET (R-LBET) model was found to be in very good agreement with the experimental data. The derived binary isosteric heat of adsorption showed that the heat was reduced by competitive adsorption but promoted by cooperative adsorption. PMID:19678623

  6. Reaching equilibrium: the role of dissipation in analogous systems, within a thermodynamic-like perspective

    NASA Astrophysics Data System (ADS)

    Bonanno, A.; Camarca, M.; Sapia, P.

    2012-11-01

    Isomorphic problems play an acknowledged pedagogical role in the physics teaching/learning process. In this context, we describe a unified approach to a wide class of physical systems formally analogous to the well-known ‘two-capacitor system’. The proposed learning path, specifically addressed to university students, provides the opportunity to introduce a unitary graphical representation that is very suitable to describe the system energy evolution, as well as allowing the highlighting of the mutually exclusive roles of dissipation and reversibility when the system approaches its equilibrium conditions (where ‘equilibrium’ must be interpreted in its most general meaning, either as ‘static equilibrium’ or as ‘steady state’). Moreover, a new quantitative modeling is introduced for two representative systems, in order to show that the energy ‘missed’ during the equilibrium achievement is just equal to the negative work an external agent should make to let the system reach its final state quasi-statically and reversibly.

  7. Effective computer simulation of equilibrium adsorption with limited solubility

    NASA Astrophysics Data System (ADS)

    Zedek, Lukáš; Šembera, Jan

    2014-12-01

    Radioactive waste repositories are discussed to be built in compact granite rock massif somewhere in the Czech Republic. To support the decision-making, various computer simulations are performed. These simulations help to evaluate risks connected with potential isolation failures, followed by transport of released radionuclides in the groundwater. Transport of radionuclides is affected by many natural processes. In this paper we focus on two important processes: adsorption and limited solubility (surface precipitation) of radionuclides in groundwater. Presented approach is based on interpolation instead of time demanding solution of nonlinear equations arising from mathematical description of the problem. The effectiveness of the proposed approach consists in creation of an interpolation table of points lying on an isotherm and transformed to mass balance maintaining system of coordinates. This kind of table is used to project data from transport part of simulation on the isotherm. The interpolation table points are computed using free derivative, nonlinear equation solver which avoids some of numerical solution difficulties. Results achieved with the use of our approach are comparable to Newton-Raphson method achieved solutions, but the simulation times are shorter.

  8. Adsorption of cellulase Aspergillus niger on a commercial activated carbon: kinetics and equilibrium studies.

    PubMed

    Daoud, Fatima Boukraa-Oulad; Kaddour, Samia; Sadoun, Tahar

    2010-01-01

    The adsorption kinetics of cellulase Aspergillus niger on a commercial activated carbon has been performed using a batch-adsorption technique. The effect of various experimental parameters such as initial enzyme concentration, contact time and temperature were investigated. The pseudo-first-order and pseudo-second-order kinetic models were used to describe the kinetic data which shows that the adsorption of the enzyme followed the pseudo-second-order rate expression and the rate constants were evaluated. The Langmuir and Freundlich adsorption isotherm models were applied to describe the equilibrium isotherms, and the isotherm constants were determined. It was found that Langmuir model was more suitable for our data. The activation energy of adsorption was also evaluated for the adsorption of enzyme onto activated carbon. It was found 11.37 kJ mol(-1). Thermodynamic parameters Delta G(0), Delta H(0) and DeltaS(0) were calculated, indicating that this process can be spontaneous and endothermic. The adsorption enthalpy and entropy were found 11.12 kJ mol(-1) and 0.084 kJ mol(-1)K(-1), respectively. At 30 degrees C and at pH 4.8, 1g activated carbon adsorbed about 1565 mg of cellulase, with a retention of 70% of the native enzyme activity up to five cycles of repeated batch enzyme reactions. PMID:19744839

  9. Equilibrium adsorption of hexahistidine on pH-responsive hydrogel nanofilms.

    PubMed

    Longo, Gabriel S; de la Cruz, Monica Olvera; Szleifer, Igal

    2014-12-23

    We present a molecular theory to study the adsorption of different species within pH-sensitive hydrogel nanofilms. The theoretical framework allows for a molecular-level description of all the components of the system, and it explicitly accounts for the acid-base equilibrium. We concentrate on the adsorption of hexahistidine, one of the most widely used tags in bio-related systems, particularly in chromatography of proteins. The adsorption of hexahistidine within a grafted polyacid hydrogel film shows a nonmonotonic dependence on the solution pH. Depending on the salt concentration, the density of the polymer network, and the bulk concentration of peptide, substantial adsorption is predicted in the intermediate pH range where both the network and the amino acids are charged. To enhance the electrostatic attractions, the acid-base equilibrium of adsorbed hexahistidine is shifted significantly, increasing the degree of charge of the residues as compared to the bulk solution. Such a shift depends critically on the conditions of the environment at the nanoscale. At the same time, the degree of dissociation of the network becomes that of the isolated acid group in a dilute solution, which means that the network is considerably more charged than when there is no adsorbate molecules. This work provides fundamental information on the physical chemistry behind the adsorption behavior and the response of the hydrogel film. This information can be useful in designing new materials for the purification or separation/immobilization of histidine-tagged proteins. PMID:25434993

  10. Thermodynamic parameters for adsorption equilibrium of heavy metals and dyes from wastewaters.

    PubMed

    Liu, Xiang; Lee, Duu-Jong

    2014-05-01

    This meta-analysis evaluates adsorption studies that report thermodynamic parameters for heavy metals and dyes from wastewaters. The adsorbents were derived from agricultural waste, industrial wastes, inorganic particulates, or some natural products. The adsorption mechanisms, derivation of thermodynamic relationships, and possible flaws made in such evaluation are discussed. This analysis shows that conclusions from the examined standard enthalpy and entropy changes are highly contestable. The reason for this flaw may be the poor physical structure of adsorbents tested, such that pore transport controlled the solute flux, leaving a surface reaction process near equilibrium. PMID:24461254

  11. Prediction of equilibrium parameters of adsorption of lead (II) ions onto diatomite

    NASA Astrophysics Data System (ADS)

    Salman, Taylan; Ardalı, Yüksel; Gamze Turan, N.

    2013-04-01

    Heavy metals from industrial wastewaters are one of the most important environmental issues to be solved today. Due to their toxicity and nonbiodegradable nature, heavy metals cause environmental and public health problems. Various techniques have been developed to remove heavy metals from aqueous solutions. These include chemical precipitation, reverse osmosis, ion Exchange and adsorption. Among them, adsorption is considered to be a particularly competitive and effective process for the removal of heavy metals from aqueous solutions. There is growing interest in using low cost, commercially available materials for the adsorption of heavy metals. Diatomite is a siliceous sedimentary rock having an amorphous form of silica (SiO2. nH2O) containing a small amount of microcrystalline material. It has unique combination of physical and chemical properties such as high porosity, high permeability, small particle size, large surface area, and low thermal conductivity. In addition, it is available in Turkey and in various locations around the world. Therefore, diatomite has been successfully used as adsorbent for the removal of heavy metals. The aim of the study is to investigate the adsorption properties of diatomite. The equilibrium adsorption data were applied to the Langmuir, Freundlich and Dubinin-Radushkevic (D-R) isotherm models. Adsorption experiments were performed under batch process, using Pb (II) initial concentration, pH of solution and contact time as variables. The results demonstrated that the adsorption of Pb (II) was strongly dependent on pH of solution. The effect of pH on adsorption of Pb(II) on diatomite was conducted by varying pH from 2 to 12 at 20 oC. In the pH range of 2.0-4.0, the adsorption percentage increases slightly as the pH increasing. At pH>4, the adsorption percentage decreases with increasing pH because hydrolysis product and the precipitation begin to play an important role in the sorption of Pb (II). At pH4, the maximum adsorption

  12. Equilibrium and kinetics studies of arsenate adsorption by FePO(4).

    PubMed

    Hamayun, M; Mahmood, T; Naeem, A; Muska, M; Din, S U; Waseem, M

    2014-03-01

    The present work is focusing on removal of arsenate from aqueous solution using FePO4. The equilibrium study regarding the removal of arsenic by FePO4 was carried out at 298, 308, 318 and 328K. Langmuir parameters were found to increase with the increase in temperature indicating that the adsorption is favorable at high temperature. Kinetic study of arsenate adsorption on FePO4 was also carried out at different temperatures and at pH 6 and 8. Different kinetic models were used to the kinetic data amongst which pseudo second order model was best fitted. The mechanism of the adsorption kinetics was investigated by employing intraparticle diffusion and Richenberg models. The energy of activation (Ea) was found to be 30 and 35.52kJmol(-1) at pH 6 and pH 8, respectively, suggesting chemisorption nature of the adsorption process. The negative entropic values of activation signified the existence of entropy barrier while the positive ΔG(#) values indicated the existence of energy barrier to be crossed over for the occurrence of a chemical reaction. Both the spectroscopic studies and increase in equilibrium pH reveal the anion exchange removal of arsenate from aqueous solution to the solid surface. PMID:24280053

  13. Kinetics and equilibrium adsorption study of p-nitrophenol onto activated carbon derived from walnut peel.

    PubMed

    Liu, Xiaohong; Wang, Fang; Bai, Song

    2015-01-01

    An original activated carbon prepared from walnut peel, which was activated by zinc chloride, was modified with ammonium hydroxide or sodium hydroxide in order to contrast the adsorption property of the three different activated carbons. The experiment used a static adsorption test for p-nitrophenol. The effects of parameters such as initial concentration, contact time and pH value on amount adsorbed and removal are discussed in depth. The thermodynamic data of adsorption were analyzed by Freundlich and Langmuir models. The kinetic data of adsorption were measured by the pseudo-first-order kinetics and the pseudo-second-order kinetics models. The results indicated that the alkalized carbon samples derived from walnut peel had a better performance than the original activated carbon treated with zinc chloride. It was found that adsorption equilibrium time was 6 h. The maximum removal rate of activated carbon treated with zinc chloride for p-nitrophenol was 87.3% at pH 3,whereas the maximum removal rate of the two modified activated carbon materials was found to be 90.8% (alkalized with ammonium hydroxide) and 92.0% (alkalized with sodium hydroxide) at the same pH. The adsorption data of the zinc chloride activated carbon were fitted to the Langmuir isotherm model. The two alkalized activated carbon samples were fitted well to the Freundlich model. The pseudo-second-order dynamics equation provided better explanation of the adsorption dynamics data of the three activated carbons than the pseudo-first-order dynamics equation. PMID:26676011

  14. Melanoidin Removal Mechanism in An Aqueous Adsorption System: An Equilibrium, Kinetic and Thermodynamic Study.

    PubMed

    Nunes, Diego L; Oliveira, Leandro S; Franca, Adriana S

    2015-01-01

    Melanoidins are colored products that can be found in food and drinks, formed by Maillard reactions. Sometimes these compounds are considered undesirable in certain food products, because they impart a brownish color and must be removed. An overview of recent patents related to melanoidin removal indicates that it can be performed by chemical/biological degradation or by adsorption processes. Therefore, in the present study, the adsorption mechanism for synthetic melanoidin removal from aqueous solutions was studied using different Raphanus sativus press-cake sorbents, with the precursor material being carbonized in a microwave oven, either with direct heating or after a chemical activation process with phosphoric acid, nitric acid or potassium hydroxide. Physical and chemical modifications were evaluated by FTIR, pHPZC, thermogravimetry and BET. The adsorption kinetics was better described by a pseudo-second order model for all activated carbons (ACs). Evaluation of the diffusion process showed dependence on the initial melanoidin concentration due to the wide range of sizes of the adsorbed molecules. The equilibrium data were best fitted by the Langmuir model for the acid-treated AC and by the Freundlich model for the base-treated and non-chemically treated ACs. Melanoidin adsorption was characterized as a spontaneous, favorable and endothermic process involving hydrogen bonds and π-π interactions between the adsorbents surfaces and the adsorbed molecules. PMID:26013772

  15. Dye removal from textile industrial effluents by adsorption on exfoliated graphite nanoplatelets: kinetic and equilibrium studies.

    PubMed

    Carvallho, Marilda N; da Silva, Karolyne S; Sales, Deivson C S; Freire, Eleonora M P L; Sobrinho, Maurício A M; Ghislandi, Marcos G

    2016-01-01

    The concept of physical adsorption was applied for the removal of direct and reactive blue textile dyes from industrial effluents. Commercial graphite nanoplatelets were used as substrate, and the quality of the material was characterized by atomic force and transmission electron microscopies. Dye/graphite nanoplatelets water solutions were prepared varying their pH and initial dye concentration. Exceptionally high values (beyond 100 mg/L) for adsorptive capacity of graphite nanoplatelets could be achieved without complicated chemical modifications, and equilibrium and kinetic experiments were performed. Our findings were compared with the state of the art, and compared with theoretical models. Agreement between them was satisfactory, and allowed us to propose novel considerations describing the interactions of the dyes and the graphene planar structure. The work highlights the important role of these interactions, which can govern the mobility of the dye molecules and the amount of layers that can be stacked on the graphite nanoplatelets surface. PMID:27148721

  16. Density functional theory of equilibrium random copolymers: application to surface adsorption of aggregating peptides

    NASA Astrophysics Data System (ADS)

    Wang, Haiqiang; Forsman, Jan; Woodward, Clifford E.

    2016-06-01

    We generalize a recently developed polymer density functional theory (PDFT) for polydisperse polymer fluids to the case of equilibrium random copolymers. We show that the generalization of the PDFT to these systems allows us to obtain a remarkable simplification compared to the monodispersed polymers. The theory is used to treat a model for protein aggregation into linear filaments in the presence of surfaces. Here we show that, for attractive surfaces, there is evidence of significant enhancement of protein aggregation. This behaviour is a consequence of a surface phase transition, which has been shown to occur with ideal equilibrium polymers in the presence of sufficiently attractive surfaces. For excluding monomers, this transition is suppressed, though an echo of the underlying ideal transition is present in the sudden change in the excess adsorption.

  17. Density functional theory of equilibrium random copolymers: application to surface adsorption of aggregating peptides.

    PubMed

    Wang, Haiqiang; Forsman, Jan; Woodward, Clifford E

    2016-06-22

    We generalize a recently developed polymer density functional theory (PDFT) for polydisperse polymer fluids to the case of equilibrium random copolymers. We show that the generalization of the PDFT to these systems allows us to obtain a remarkable simplification compared to the monodispersed polymers. The theory is used to treat a model for protein aggregation into linear filaments in the presence of surfaces. Here we show that, for attractive surfaces, there is evidence of significant enhancement of protein aggregation. This behaviour is a consequence of a surface phase transition, which has been shown to occur with ideal equilibrium polymers in the presence of sufficiently attractive surfaces. For excluding monomers, this transition is suppressed, though an echo of the underlying ideal transition is present in the sudden change in the excess adsorption. PMID:27115518

  18. Equilibrium and kinetic adsorption study of Basic Yellow 28 and Basic Red 46 by a boron industry waste.

    PubMed

    Olgun, Asim; Atar, Necip

    2009-01-15

    In this study, the adsorption characteristics of Basic Yellow 28 (BY 28) and Basic Red 46 (BR 46) onto boron waste (BW), a waste produced from boron processing plant were investigated. The equilibrium adsorption isotherms and kinetics were investigated. The adsorption equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that adsorption behavior of two dyes could be described reasonably well by a generalized isotherm. Kinetic studies indicated that the kinetics of the adsorption of BY 28 and BR 46 onto BW follows a pseudo-second-order model. The result showed that the BW exhibited high-adsorption capacity for basic dyes and the capacity slightly decreased with increasing temperature. The maximum adsorption capacities of BY 28 and BR 46 are reported at 75.00 and 74.73mgg(-1), respectively. The dye adsorption depended on the initial pH of the solution with maximum uptake occurring at about pH 9 and electrokinetic behavior of BW. Activation energy of 15.23kJ/mol for BY 28 and 18.15kJ/mol for BR 46 were determined confirming the nature of the physisorption onto BW. These results indicate that BW could be employed as low-cost material for the removal of the textile dyes from effluents. PMID:18434000

  19. Adsorption of reactive blue BF-5G dye by soybean hulls: kinetics, equilibrium and influencing factors.

    PubMed

    Honorio, Jacqueline Ferandin; Veit, Márcia Teresinha; Gonçalves, Gilberto da Cunha; de Campos, Élvio Antonio; Fagundes-Klen, Márcia Regina

    2016-01-01

    The textile industry is known for the high use of chemicals, such as dyes, and large volumes of effluent that contaminate waters, a fact that has encouraged research and improved treatment techniques. In this study, we used unprocessed soybean hulls for the removal of reactive blue BF-5G dye. The point of zero charge of soybean hulls was 6.76. Regarding the speed of agitation in the adsorption process, the resistance to mass transfer that occurs in the boundary layer was eliminated at 100 rpm. Kinetics showed an experimental amount of dye adsorbed at equilibrium of 57.473 mg g(-1) obtained under the following conditions: dye initial concentration = 400 mg L(-1); diameter of particle = 0.725 mm; dosage = 6 g L(-1); pH 2; 100 rpm; temperature = 30 °C; and duration of 24 hours. The pseudo-second order best showed the dye removal kinetics. The adsorption isotherms performed at different temperatures (20, 30, 40 and 50 °C) showed little variation in the concentration range assessed, being properly adjusted by the Langmuir isotherm model. The maximum capacity of dye adsorption was 72.427 mg g(-1) at 30 °C. Since soybean hull is a low-cost industrial byproduct, it proved to be a potential adsorbent for the removal of the textile dye assessed. PMID:26942540

  20. Equilibrium and kinetic studies of adsorption of phosphate onto ZnCl2 activated coir pith carbon.

    PubMed

    Namasivayam, C; Sangeetha, D

    2004-12-15

    Phosphate removal from aqueous solution was investigated using ZnCl(2)-activated carbon developed from coir pith, an agricultural solid waste. Studies were conducted to delineate the effect of contact time, adsorbent dose, phosphate concentration, pH, and temperature. The adsorption equilibrium data followed both Langmuir and Freundlich isotherms. Langmuir adsorption capacity was found to be 5.1 mg/g. Adsorption followed second-order kinetics. The removal was maximum in the pH range 3-10. pH effect and desorption studies showed that adsorption occurred by both ion exchange and chemisorption mechanisms. Adsorption was found to be spontaneous and endothermic. Effect of foreign ions on adsorption shows that perchlorate, sulfate, and selenite decreased the percent removal of phosphate. PMID:15533408

  1. Low-pressure equilibrium binary argon-methane gas mixture adsorption on exfoliated graphite: Experiments and simulations

    NASA Astrophysics Data System (ADS)

    Albesa, Alberto; Russell, Brice; Vicente, José Luis; Rafti, Matías

    2016-04-01

    Adsorption equilibrium measurements of pure methane, pure argon, and binary mixtures over exfoliated graphite were carried for different initial compositions, temperatures, and total pressures in the range of 0.1-1.5 Torr using the volumetric static method. Diagrams for gas and adsorbed phase compositions were constructed for the conditions explored, and isosteric heats of adsorption were calculated. Experimental results were compared with predictions obtained with Monte Carlo simulations and using the Ideal Adsorbed Solution Theory (IAST).

  2. Equilibrium, kinetic and thermodynamic studies on the adsorption of the toxins of Bacillus thuringiensis subsp. kurstaki by clay minerals

    NASA Astrophysics Data System (ADS)

    Fu, Qingling; Deng, Yali; Li, Huishu; Liu, Jie; Hu, Hongqing; Chen, Shouwen; Sa, Tongmin

    2009-02-01

    The persistence of Bacillus thuringiensis ( Bt) toxins in soil is further enhanced through association with soil particles. Such persistence may improve the effectiveness of controlling target pests, but impose a hazard to non-target organisms in soil ecosystems. In this study, the equilibrium adsorption of the Bt toxin by four clay minerals (montmorillonite, kaolinite, goethite, and silicon dioxide) was investigated, and the kinetic and thermodynamic parameters were calculated. The results showed that Bt toxin could be adsorbed easily by minerals, and the adsorption was much easier at low temperature than at high temperature at the initial concentration varying from 0 to 1000 mg L -1. The adsorption fitted well to both Langmuir and Freundlich isotherm models, but the Freundlich equation was more suitable. The pseudo-second-order (PSO) was the best application model to describe the adsorption kinetic. The adsorption process appeared to be controlled by chemical process, and the intra-particle diffusion was not the only rate-controlling step. The negative standard free energy ( ΔGmθr) values of the adsorption indicated that the adsorption of the Bt toxin by the minerals was spontaneous, and the changes of the standard enthalpy ( ΔHmθr) showed that the adsorption of the Bt toxin by montmorillonite was endothermic while the adsorption by the other three minerals was exothermic.

  3. Adsorption of reactive dyes from aqueous solutions by fly ash: kinetic and equilibrium studies.

    PubMed

    Dizge, N; Aydiner, C; Demirbas, E; Kobya, M; Kara, S

    2008-02-11

    Adsorption kinetic and equilibrium studies of three reactive dyes namely, Remazol Brillant Blue (RB), Remazol Red 133 (RR) and Rifacion Yellow HED (RY) from aqueous solutions at various initial dye concentration (100-500 mg/l), pH (2-8), particle size (45-112.5 microm) and temperature (293-323 K) on fly ash (FA) were studied in a batch mode operation. The adsorbent was characterized with using several methods such as SEM, XRD and FTIR. Adsorption of RB reactive dye was found to be pH dependent but both RR and RY reactive dyes were not. The result showed that the amount adsorbed of the reactive dyes increased with increasing initial dye concentration and contact time. Batch kinetic data from experimental investigations on the removal of reactive dyes from aqueous solutions using FA have been well described by external mass transfer and intraparticle diffusion models. It was found that external mass transfer and intraparticle diffusion had rate limiting affects on the removal process. This was attributed to the relatively simple macropore structure of FA particles. The adsorption data fitted well with Langmuir and Freundlich isotherm models. The optimum conditions for removal of the reactive dyes were 100mg/l initial dye concentration, 0.6g/100ml adsorbent dose, temperature of 293 K, 45 microm particle size, pH 6 and agitation speed of 250 rpm, respectively. The values of Langmuir and Freundlich constants were found to increase with increasing temperature in the range 135-180 and 15-34 mg/g for RB, 47-86 and 1.9-3.7 mg/g for RR and 37-61 and 3.0-3.6 mg/g for RY reactive dyes, respectively. Different thermodynamic parameters viz., changes in standard free energy, enthalpy and entropy were evaluated and it was found that the reaction was spontaneous and endothermic in nature. PMID:17574338

  4. A procedure to find thermodynamic equilibrium constants for CO2 and CH4 adsorption on activated carbon.

    PubMed

    Trinh, T T; van Erp, T S; Bedeaux, D; Kjelstrup, S; Grande, C A

    2015-03-28

    Thermodynamic equilibrium for adsorption means that the chemical potential of gas and adsorbed phase are equal. A precise knowledge of the chemical potential is, however, often lacking, because the activity coefficient of the adsorbate is not known. Adsorption isotherms are therefore commonly fitted to ideal models such as the Langmuir, Sips or Henry models. We propose here a new procedure to find the activity coefficient and the equilibrium constant for adsorption which uses the thermodynamic factor. Instead of fitting the data to a model, we calculate the thermodynamic factor and use this to find first the activity coefficient. We show, using published molecular simulation data, how this procedure gives the thermodynamic equilibrium constant and enthalpies of adsorption for CO2(g) on graphite. We also use published experimental data to find similar thermodynamic properties of CO2(g) and of CH4(g) adsorbed on activated carbon. The procedure gives a higher accuracy in the determination of enthalpies of adsorption than ideal models do. PMID:25732332

  5. Quantifying differences in the impact of variable chemistry on equilibrium uranium(VI) adsorption properties of aquifer sediments

    SciTech Connect

    Stoliker, Deborah L.; Kent, Douglas B.; Zachara, John M.

    2011-09-16

    Uranium adsorption-desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500-1000 hours although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A non-electrostatic surface complexation reaction, >SOH + UO22+ + 2CO32- = >SOUO2(CO3HCO3)2-, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logKc) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logKc values. Using this approach, logKc values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (<0.063 mm) of another could be demonstrated despite the fines requiring a different reaction stoichiometry. Estimates of logKc uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors.

  6. Quantifying differences in the impact of variable chemistry on equilibrium uranium(VI) adsorption properties of aquifer sediments

    USGS Publications Warehouse

    Stoliker, Deborah L.; Kent, Douglas B.; Zachara, John M.

    2011-01-01

    Uranium adsorption-desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500-1000 h although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A nonelectrostatic surface complexation reaction, >SOH + UO22+ + 2CO32- = >SOUO2(CO3HCO3)2-, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logKc) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logKc values. Using this approach, logKc values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (Kc uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors.

  7. Integrating reinforcement learning, equilibrium points, and minimum variance to understand the development of reaching: a computational model.

    PubMed

    Caligiore, Daniele; Parisi, Domenico; Baldassarre, Gianluca

    2014-07-01

    Despite the huge literature on reaching behavior, a clear idea about the motor control processes underlying its development in infants is still lacking. This article contributes to overcoming this gap by proposing a computational model based on three key hypotheses: (a) trial-and-error learning processes drive the progressive development of reaching; (b) the control of the movements based on equilibrium points allows the model to quickly find the initial approximate solution to the problem of gaining contact with the target objects; (c) the request of precision of the end movement in the presence of muscular noise drives the progressive refinement of the reaching behavior. The tests of the model, based on a two degrees of freedom simulated dynamical arm, show that it is capable of reproducing a large number of empirical findings, most deriving from longitudinal studies with children: the developmental trajectory of several dynamical and kinematic variables of reaching movements, the time evolution of submovements composing reaching, the progressive development of a bell-shaped speed profile, and the evolution of the management of redundant degrees of freedom. The model also produces testable predictions on several of these phenomena. Most of these empirical data have never been investigated by previous computational models and, more important, have never been accounted for by a unique model. In this respect, the analysis of the model functioning reveals that all these results are ultimately explained, sometimes in unexpected ways, by the same developmental trajectory emerging from the interplay of the three mentioned hypotheses: The model first quickly learns to perform coarse movements that assure a contact of the hand with the target (an achievement with great adaptive value) and then slowly refines the detailed control of the dynamical aspects of movement to increase accuracy. PMID:25090425

  8. Adsorption and desorption of arsenate on sandy sediments from contaminated and uncontaminated saturated zones: Kinetic and equilibrium modeling.

    PubMed

    Hafeznezami, Saeedreza; Zimmer-Faust, Amity G; Dunne, Aislinn; Tran, Tiffany; Yang, Chao; Lam, Jacquelyn R; Reynolds, Matthew D; Davis, James A; Jay, Jennifer A

    2016-08-01

    Application of empirical models to adsorption of contaminants on natural heterogeneous sorbents is often challenging due to the uncertainty associated with fitting experimental data and determining adjustable parameters. Sediment samples from contaminated and uncontaminated portions of a study site in Maine, USA were collected and investigated for adsorption of arsenate [As(V)]. Two kinetic models were used to describe the results of single solute batch adsorption experiments. Piecewise linear regression of data linearized to fit pseudo-first order kinetic model resulted in two distinct rates and a cutoff time point of 14-19 h delineating the biphasic behavior of solute adsorption. During the initial rapid adsorption stage, an average of 60-80% of the total adsorption took place. Pseudo-second order kinetic models provided the best fit to the experimental data (R(2) > 0.99) and were capable of describing the adsorption over the entire range of experiments. Both Langmuir and Freundlich isotherms provided reasonable fits to the adsorption data at equilibrium. Langmuir-derived maximum adsorption capacity (St) of the studied sediments ranged between 29 and 97 mg/kg increasing from contaminated to uncontaminated sites. Solid phase As content of the sediments ranged from 3.8 to 10 mg/kg and the As/Fe ratios were highest in the amorphous phase. High-pH desorption experiments resulted in a greater percentage of solid phase As released into solution from experimentally-loaded sediments than from the unaltered samples suggesting that As(V) adsorption takes place on different reversible and irreversible surface sites. PMID:27218893

  9. Batch removal of malachite green from aqueous solutions by adsorption on oil palm trunk fibre: equilibrium isotherms and kinetic studies.

    PubMed

    Hameed, B H; El-Khaiary, M I

    2008-06-15

    Oil palm trunk fibre (OPTF)--an agricultural solid waste--was used as low-cost adsorbent to remove malachite green (MG) from aqueous solutions. The operating variables studied were contact time, initial dye concentration, and solution pH. Equilibrium adsorption data were analyzed by three isotherms, namely the Freundlich isotherm, the Langmuir isotherm, and the multilayer adsorption isotherm. The best fit to the data was obtained with the multilayer adsorption. The monolayer adsorption capacity of OPTF was found to be 149.35 mg/g at 30 degrees C. Adsorption kinetic data were modeled using the Lagergren pseudo-first-order, Ho's pseudo-second-order and Elovich models. It was found that the Lagergren's model could be used for the prediction of the system's kinetics. The overall rate of dye uptake was found to be controlled by external mass transfer at the beginning of adsorption, then for initial MG concentrations of 25, 50, 100, 150, and 300 mg/L the rate-control changed to intraparticle diffusion at a later stage, but for initial MG concentrations 200 and 250 mg/L no evidence was found of intraparticle diffusion at any period of adsorption. It was found that with increasing the initial concentration of MG, the pore-diffusion coefficient increased while the film-diffusion coefficient decreased. PMID:18022316

  10. Quantifying Differences in the Impact of Variable Chemistry on Equilibrium Uranium(VI) Adsorption Properties of Aquifer Sediments

    PubMed Central

    2011-01-01

    Uranium adsorption–desorption on sediment samples collected from the Hanford 300-Area, Richland, WA varied extensively over a range of field-relevant chemical conditions, complicating assessment of possible differences in equilibrium adsorption properties. Adsorption equilibrium was achieved in 500–1000 h although dissolved uranium concentrations increased over thousands of hours owing to changes in aqueous chemical composition driven by sediment-water reactions. A nonelectrostatic surface complexation reaction, >SOH + UO22+ + 2CO32- = >SOUO2(CO3HCO3)2–, provided the best fit to experimental data for each sediment sample resulting in a range of conditional equilibrium constants (logKc) from 21.49 to 21.76. Potential differences in uranium adsorption properties could be assessed in plots based on the generalized mass-action expressions yielding linear trends displaced vertically by differences in logKc values. Using this approach, logKc values for seven sediment samples were not significantly different. However, a significant difference in adsorption properties between one sediment sample and the fines (<0.063 mm) of another could be demonstrated despite the fines requiring a different reaction stoichiometry. Estimates of logKc uncertainty were improved by capturing all data points within experimental errors. The mass-action expression plots demonstrate that applying models outside the range of conditions used in model calibration greatly increases potential errors. PMID:21923109

  11. Adsorption equilibrium of binary methane/ethane mixtures in BPL activated carbon: isotherms and calorimetric heats of adsorption.

    PubMed

    He, Yufeng; Yun, Jeong-Ho; Seaton, Nigel A

    2004-08-01

    The adsorption of pure methane and ethane in BPL activated carbon has been measured at temperatures between 264 and 373 K and at pressures up to 3.3 MPa with a bench-scale high-pressure open-flow apparatus. The same apparatus was used to measure the adsorption of binary methane/ethane mixtures in BPL at 301.4 K and at pressures up to 2.6 MPa. Thermodynamic consistency tests demonstrate that the data are thermodynamically consistent. In contrast to two sets of data previously published, we found that the adsorption of binary methane/ethane in BPL behaves ideally (in the sense of obeying ideal adsorbed solution theory, IAST) throughout the pressure and gas-phase composition range studied. A Tian-Calvet type microcalorimeter was used to measure low-pressure isotherms, the isosteric heats of adsorption of pure methane and ethane in BPL activated carbon, and the individual heats of adsorption in binary mixtures, at 297 K and at pressures up to 100 kPa. The mixture heats of adsorption were consistent with IAST. PMID:15274571

  12. Rapid Adsorption of Copper(II) and Lead(II) by Rice Straw/Fe3O4 Nanocomposite: Optimization, Equilibrium Isotherms, and Adsorption Kinetics Study

    PubMed Central

    Khandanlou, Roshanak; Ahmad, Mansor B.; Fard Masoumi, Hamid Reza; Shameli, Kamyar; Basri, Mahiran; Kalantari, Katayoon

    2015-01-01

    Rice straw/magnetic nanocomposites (RS/Fe3O4-NCs) were prepared via co-precipitation method for removal of Pb(II) and Cu(II) from aqueous solutions. Response surface methodology (RSM) was utilized to find the optimum conditions for removal of ions. The effects of three independent variables including initial ion concentration, removal time, and adsorbent dosage were investigated on the maximum adsorption of Pb (II) and Cu (II). The optimum conditions for the adsorption of Pb(II) and Cu(II) were obtained (100 and 60 mg/L) of initial ion concentration, (41.96 and 59.35 s) of removal time and 0.13 g of adsorbent for both ions, respectively. The maximum removal efficiencies of Pb(II) and Cu(II) were obtained 96.25% and 75.54%, respectively. In the equilibrium isotherm study, the adsorption data fitted well with the Langmuir isotherm model. The adsorption kinetics was best depicted by the pseudo-second order model. Desorption experiments showed adsorbent can be reused successfully for three adsorption-desorption cycles. PMID:25815470

  13. The effect of water temperature on the adsorption equilibrium of dissolved organic matter and atrazine on granular activated carbon

    SciTech Connect

    Bernd Schreiber; Viktor Schmalz; Thomas Brinkmann; Eckhard Worch

    2007-09-15

    The influence of water temperature on the adsorption of natural dissolved organic matter (DOM) on activated carbon has not been investigated intensively yet. In this study, batch experiments with granular activated carbon (GAC) F300, from bituminous coal, have been carried out at three temperatures (5, 20, 35{sup o} C) using a humic acid model water and different types of surface water (lake, river, canal). Furthermore, the adsorption of an anthropogenic contaminant, atrazine, was quantified in the absence and presence of DOM. The results indicate a significant influence of water temperature on the adsorption equilibrium of DOM and atrazine. Contrary to expectations, DOM and atrazine adsorption in surface water tends to be increased with increasing water temperature, whereas the extent of this effect is dependent on the type and concentration of DOM. Furthermore, the temperature effect on atrazine adsorption is controlled by competition of DOM and atrazine on adsorption sites. Some assumptions are proposed and discussed for explaining the temperature effects observed in the batch studies. 39 refs., 4 figs., 2 tabs.

  14. Kinetics, equilibrium, and thermodynamics investigation on the adsorption of lead(II) by coal-based activated carbon.

    PubMed

    Yi, Zhengji; Yao, Jun; Zhu, Mijia; Chen, Huilun; Wang, Fei; Liu, Xing

    2016-01-01

    The goal of this research is to investigate the feasibility of using activated coal-based activated carbon (CBAC) to adsorb Pb(II) from aqueous solutions through batch tests. Effects of contact time, pH, temperature and initial Pb(II) concentration on the Pb(II) adsorption were examined. The Pb(II) adsorption is strongly dependent on pH, but insensitive to temperature. The best pH for Pb(II) removal is in the range of 5.0-5.5 with more than 90 % of Pb(II) removed. The equilibrium time was found to be 60 min and the adsorption data followed the pseudo-second-order kinetics. Isotherm data followed Langmuir isotherm model with a maximum adsorption capacity of 162.33 mg/g. The adsorption was exothermic and spontaneous in nature. The Fourier transform infrared spectroscopy and scanning electron microscopy analysis suggested that CBAC possessed a porous structure and was rich in carboxyl and hydroxyl groups on its surface, which might play a major role in Pb(II) adsorption. These findings indicated that CBAC has great potential as an alternative adsorbent for Pb(II) removal. PMID:27504258

  15. Adsorption of Zn2+ ions onto NaA and NaX zeolites: kinetic, equilibrium and thermodynamic studies.

    PubMed

    Nibou, D; Mekatel, H; Amokrane, S; Barkat, M; Trari, M

    2010-01-15

    The adsorption of Zn(2+) onto NaA and NaX zeolites was investigated. The samples were synthesized according to a hydrothermal crystallization using aluminium isopropoxide (Al[OCH(CH(3))(2)](3)) as a new alumina source. The effects of pH, initial concentration, solid/liquid ratio and temperature were studied in batch experiments. The Freundlich and the Langmuir models were applied and the adsorption equilibrium followed Langmuir adsorption isotherm. The uptake distribution coefficient (K(d)) indicated that the Zn(2+) removal was the highest at minimum concentration. Thermodynamic parameters were calculated. The negative values of standard enthalpy of adsorption revealed the exothermic nature of the adsorption process whereas the negative activation entropies reflected that no significant change occurs in the internal structure of the zeolites solid matrix during the sorption of Zn(2+). The negative values of Gibbs free energy were indicative of the spontaneity of the adsorption process. Analysis of the kinetic and rate data revealed that the pseudo second-order sorption mechanism is predominant and the intra particle diffusion was the determining step for the sorption of zinc ions. The obtained optimal parameters have been applied to wastewater from the industrial zone (Algeria) in order to remove the contained zinc effluents. PMID:19773115

  16. An Equilibrium Model for the Combined Effect of Macromolecular Crowding and Surface Adsorption on the Formation of Linear Protein Fibrils

    PubMed Central

    Hoppe, Travis; Minton, Allen P.

    2015-01-01

    The formation of linear protein fibrils has previously been shown to be enhanced by volume exclusion or crowding in the presence of a high concentration of chemically inert protein or polymer, and by adsorption to membrane surfaces. An equilibrium mesoscopic model for the combined effect of both crowding and adsorption upon the fibrillation of a dilute tracer protein is presented. The model exhibits behavior that differs qualitatively from that observed in the presence of crowding or adsorption alone. The model predicts that in a crowded solution, at critical values of the volume fraction of crowder or intrinsic energy of the tracer-wall interaction, the tracer protein will undergo an extremely cooperative transition—approaching a step function—from existence as a slightly self-associated species in solution to existence as a highly self-associated and completely adsorbed species. Criteria for a valid experimental test of these predictions are presented. PMID:25692600

  17. Adsorption behaviour of direct yellow 50 onto cotton fiber: equilibrium, kinetic and thermodynamic profile.

    PubMed

    Ismail, L F M; Sallam, H B; Abo Farha, S A; Gamal, A M; Mahmoud, G E A

    2014-10-15

    This study investigated the adsorption of direct yellow 50 onto cotton fiber from aqueous solution by using parameters, such as pH, temperature, contact time, initial dye concentration and the effect of sodium sulphate, tetrasodium edate and trisodium citrate. The extent of dye adsorption increased with increasing contact time, temperature and solution concentration. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption. It was found that the Langmuir equation fit better than the Freundlich equation. The results show that the presence of SE and SC significantly enhance the dye adsorption onto cotton fiber. In addition, the adsorption data obtained at different temperatures of DY50 onto cotton fiber were applied to pseudo first-order, pseudo second-order and intraparticle diffusion models. The rates of adsorption were found to conform to pseudo second-order kinetics with good correlation. Also, free energy of adsorption (ΔG(#)), enthalpy (ΔH(#)), and entropy (ΔS(#)) changes were determined to predict the nature of adsorption. The positive value of the enthalpy change indicated that the adsorption is endothermic process. The activation energy, Ea, is ranged between 1.9 and 3.9kJmol(-1) indicated that the adsorption process is a physisorption. This low value of Ea generally indicates diffusion controlled process. PMID:24882703

  18. Adsorption behavior of activated carbon derived from pyrolusite-modified sewage sludge: equilibrium modeling, kinetic and thermodynamic studies.

    PubMed

    Chen, Yao; Jiang, Wenju; Jiang, Li; Ji, Xiujuan

    2011-01-01

    Activated carbon was developed from sewage sludge using pyrolusite as an additive. It was demonstrated that the removal efficiency of two synthetic dyes (Tracid orange GS and Direct fast turquoise blue GL) by the produced adsorbent was up to 97.6%. The activated carbon with pyrolusite addition had 38.2% higher surface area, 43.8% larger micropore and 54.4% larger mesopore production than ordinary sludge-based activated carbons. Equilibrium adsorption isotherms and kinetics were also investigated based on dyes adsorption tests. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption, and the results fitted well to the Langmuir isotherm. The kinetic data have been analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion equation. The experimental data fitted very well with pseudo-second-order kinetic model. Activation energies for the adsorption processes ranged between 8.7 and 19.1 kJ mol 1. Thermodynamic parameters such as standard free energy (deltaG0), standard enthalpy (deltaH0) and standard entropy (deltaS0) were evaluated. The adsorption of these two dyes on the activated carbon was found to be a spontaneous and endothermic process in nature. PMID:22097045

  19. Adsorption behavior of direct red 80 and congo red onto activated carbon/surfactant: Process optimization, kinetics and equilibrium

    NASA Astrophysics Data System (ADS)

    Cheng, Zhengjun; Zhang, Lei; Guo, Xiao; Jiang, Xiaohui; Li, Tian

    2015-02-01

    Adsorptions of congo red and direct red 80 onto activated carbon/surfactant from aqueous solution were optimized. The Box-Behnken design (BBD) has been employed to analyze the effects of concentration of surfactant, temperature, pH, and initial concentration of the dye in the adsorption capacity. Their corresponding experimental data could be evaluated excellently by second order polynomial regression models and the two models were also examined based on the analysis of variance and t test statistics, respectively. The optimum conditions were obtained as follows: Cs = 34.10 μM, T = 50 °C, pH = 3.5, and CCR = 160 mg/L for the congo red system, and Cs = 34.10 μM, T = 50 °C, pH = 6.1, and CDR80 = 110 mg/L for the direct red 80 system. And in these conditions, the measured experimental maximum adsorption capacities for the congo red and direct red 80 removals were 769.48 mg/g and 519.90 mg/g, which were consistent with their corresponding predicted values, with small relative errors of -2.81% and -0.67%, respectively. The adsorption equilibrium and kinetics for the two dye adsorptions onto AC/DDAC were also investigated. The experimental data were fitted by four isotherm models, and Langmuir model presented the best fit. The kinetic studies indicated that the kinetic data followed the pseudo-second-order model.

  20. Utilization of extracellular information before ligand-receptor binding reaches equilibrium expands and shifts the input dynamic range

    PubMed Central

    Ventura, Alejandra C.; Bush, Alan; Vasen, Gustavo; Goldín, Matías A.; Burkinshaw, Brianne; Bhattacharjee, Nirveek; Folch, Albert; Brent, Roger; Chernomoretz, Ariel; Colman-Lerner, Alejandro

    2014-01-01

    Cell signaling systems sense and respond to ligands that bind cell surface receptors. These systems often respond to changes in the concentration of extracellular ligand more rapidly than the ligand equilibrates with its receptor. We demonstrate, by modeling and experiment, a general “systems level” mechanism cells use to take advantage of the information present in the early signal, before receptor binding reaches a new steady state. This mechanism, pre-equilibrium sensing and signaling (PRESS), operates in signaling systems in which the kinetics of ligand-receptor binding are slower than the downstream signaling steps, and it typically involves transient activation of a downstream step. In the systems where it operates, PRESS expands and shifts the input dynamic range, allowing cells to make different responses to ligand concentrations so high as to be otherwise indistinguishable. Specifically, we show that PRESS applies to the yeast directional polarization in response to pheromone gradients. Consideration of preexisting kinetic data for ligand-receptor interactions suggests that PRESS operates in many cell signaling systems throughout biology. The same mechanism may also operate at other levels in signaling systems in which a slow activation step couples to a faster downstream step. PMID:25172920

  1. Characterizing particle-scale equilibrium adsorption and kinetics of uranium(VI) desorption from U-contaminated sediments

    SciTech Connect

    Stoliker, Deborah L.; Liu, Chongxuan; Kent, Douglas B.; Zachara, John M.

    2013-02-12

    Rates of contaminant U(VI) release from individual size fractions of a composite sediment from the seasonally saturated lower vadose zone of the Hanford 300-Area were examined in flow-through batch reactors to maintain quasi-constant chemical conditions. Variability in equilibrium adsorption among the various size fractions was determined in static batch reactors and analyzed using the surface complexation modeling approach. The estimated stoichiometric coefficients of U(VI) surface complexation reactions with respect to pH and carbonate concentrations varied with size fractions. This source of variability significantly increased the uncertainty in U(VI) conditional equilibrium constants over that estimated from experimental errors alone. A minimum difference between conditional equilibrium constants was established in order to evaluate statistically significant differences between sediment adsorption properties. A set of equilibrium and kinetic expressions for cation exchange, calcite dissolution, aerobic respiration, and silica dissolution were incorporated in a reaction-rate model to describe the temporal evolution of solute concentrations observed during the flow-through batch experiments. Parameters in the reaction-rate model, calibrated using experimental data for select size fractions, predicted the changes in solute concentrations for the bulk, <2 mm, sediment sample. Kinetic U(VI) desorption was well described using a multi-rate surface complexation model with an assumed lognormal distribution for the rate constants. The estimated mean and standard deviation were the same for all < 2mm size fractions, but differed in the 2-8mm size fraction. Micropore volumes in the varied size fractions were also similar as assessed using t-plots to analyze N2 desorption data. These findings provide further support for the link between microporosity and particle-scale mass transfer rates controlling kinetic U(VI) adsorption/desorption and for the utility of N2 desorption

  2. Development, Construction, and Operation of a Multisample Volumetric Apparatus for the Study of Gas Adsorption Equilibrium

    ERIC Educational Resources Information Center

    Ribeiro, Rui P. P. L.; Silva, Ricardo J. S.; Esteves, Isabel A. A. C.; Mota, Jose´ P. B.

    2015-01-01

    The construction of a simple volumetric adsorption apparatus is highlighted. The setup is inexpensive and provides a clear demonstration of gas phase adsorption concepts. The topic is suitable for undergraduate chemistry and chemical engineering students. Moreover, this unit can also provide quantitative data that can be used by young researchers…

  3. Adsorption removal of tetracycline from aqueous solution by anaerobic granular sludge: equilibrium and kinetic studies.

    PubMed

    Li, Ke; Ji, Feng; Liu, Yuanlu; Tong, Zilin; Zhan, Xinmin; Hu, Zhenhu

    2013-01-01

    High concentration animal wastewater is often contaminated by tetracycline and an upflow anaerobic sludge bioreactor (UASB) with granular sludge is often used to treat the wastewater. The investigation of the adsorption process of tetracycline on anaerobic granular sludge during anaerobic digestion of animal wastewater will increase the understanding of antibiotics behavior in the UASB reactor. In this study, the effects of initial pH, humic acid concentration, and temperature on the removal of tetracycline by anaerobic granular sludge from aqueous solution were investigated using the batch adsorption technique in 100 mL flasks with 75 mL of work volume. The results show that the highest removal efficiency of 93.0% was achieved around pH 3.0 and the removal efficiency at the neutral pH range (pH 6.0-8.0) is about 91.5%. The thermodynamic analysis indicates that the adsorption is a spontaneous and endothermic process. The adsorption kinetics followed the pseudo-second-order equation. The adsorption isotherms analysis indicates that the Langmuir model is better than the Freundlich model for the description of the adsorption process and confirms the result of thermodynamics analysis. The maximum adsorption capacities were 2.984, 4.108 and 4.618 mg/g at 25, 35 and 45 °C, respectively. These results provide useful information for understanding the fate and transformation of tetracycline in a UASB digestion system and improving the management of tetracycline contaminated animal wastewater. PMID:23552236

  4. Kinetic and equilibrium studies of adsorptive removal of phenol onto eggshell waste.

    PubMed

    Daraei, H; Mittal, A; Noorisepehr, M; Daraei, F

    2013-07-01

    The aim of the present research is to develop economic, fast, and versatile method for the removal of toxic organic pollutant phenol from wastewater using eggshell. The batch experiments are conducted to evaluate the effect of pH, phenol concentration, dosage of adsorbent, and contact time on the removal of phenol. The paper includes in-depth kinetic studies of the ongoing adsorption process. Attempts have also been made to verify Langmuir and Freundlich adsorption isotherms. The morphology and characteristics of eggshell have also been studied using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and X-ray fluorescence analysis. At ambient temperature, the maximum adsorption of phenol onto eggshells has been achieved at pH 9 and the contact time, 90 min. The experimental data give best-fitted straight lines for pseudo-first-order as well as pseudo-second-order kinetic models. Furthermore, the adsorption process verifies Freundlich and Langmuir adsorption isotherms, and on the basis of mathematical expressions of these models, various necessary adsorption constants have been calculated. Using adsorption data, various thermodynamic parameters like change in enthalpy (∆H(0)), change in entropy (∆S(0)), and change in free energy ∆G(0) have also been evaluated. Results clearly reveal that the solid waste material eggshell acts as an effective adsorbent for the removal of phenol from aqueous solutions. PMID:23274804

  5. Adsorption kinetics and equilibrium study of nitrogen species onto radiata pine (Pinus radiata) sawdust.

    PubMed

    Harmayani, Kadek D; Faisal Anwar, A H M

    2016-01-01

    Nitrogen species (NH3-N, NO3-N, and NO2-N) are found as one of the major dissolved constituents in wastewater or stormwater runoff. In this research, laboratory experiments were conducted to remove these pollutants from the water environment using radiata pine (Pinus radiata) sawdust. A series of batch tests was conducted by varying initial concentration, dosage, particle size, pH, and contact time to check the removal performance. Test results confirmed the effectiveness of radiata pine sawdust for removing these contaminants from the aqueous phase (100% removal of NO3-N, and NO2-N; 55% removal of NH3-N). The adsorbent dosage and initial concentration showed a significantly greater effect on the removal process over pH or particle sizes. The optimum dosage for contaminant removal on a laboratory scale was found to be 12 g. Next, the adsorption kinetics were studied using intraparticle diffusion, liquid-film diffusion, and a pseudo-first order and pseudo-second order model. The adsorption of all species followed a pseudo-second order model but NO2-N adsorption followed both models. In addition, the kinetics of NO2-N adsorption showed two-step adsorption following intraparticle diffusion and liquid-film diffusion. The isotherm study showed that NO3-N and NO2-N adsorption fitted slightly better with the Freundlich model but that NH3-N adsorption followed both Freundlich and Langmuir models. PMID:27438245

  6. Adsorption equilibrium of organic vapors on single-walled carbon nanotubes

    USGS Publications Warehouse

    Agnihotri, S.; Rood, M.J.; Rostam-Abadi, M.

    2005-01-01

    Gravimetric techniques were employed to determine the adsorption capacities of commercially available purified electric arc and HiPco single-walled carbon nanotubes (SWNTs) for organic compounds (toluene, methyl ethyl ketone (MEK), hexane and cyclohexane) at relative pressures, p/p0, ranging from 1 ?? 10-4 to 0.95 and at isothermal conditions of 25, 37 and 50 ??C. The isotherms displayed both type I and type II characteristics. Adsorption isotherm modeling showed that SWNTs are heterogeneous adsorbents, and the Freundlich equation best describes the interaction between organic molecules and SWNTs. The heats of adsorption were 1-4 times the heats of vaporization, which is typical for physical adsorption of organic vapors on porous carbons. ?? 2005 Elsevier Ltd. All rights reserved.

  7. Kinetics and equilibrium studies of adsorption of chromium(VI) ion from industrial wastewater using Chrysophyllum albidum (Sapotaceae) seed shells.

    PubMed

    Amuda, O S; Adelowo, F E; Ologunde, M O

    2009-02-01

    A new biosorbent has been prepared by coating Chrysophyllum albidum (Sapotaceae) seed shells with chitosan and/or oxidizing agents such as sulfuric acid. This study investigated the technical feasibility of activated and modified activated C. albidum seed shells carbons for the adsorption of chromium(VI) from aqueous solution. The sorption process with respect to its equilibria and kinetics as well as the effects of pH, contact time, adsorbent mass, adsorbate concentration and particle size on adsorption was also studied. The most effective pH range was found to be between 4.5 and 5 for the sorption of the metal ion. The pseudo-first-order rate equation by Lagergren and pseudo-second-order rate equation were tested on the kinetic data, the adsorption process followed pseudo-second-order rate kinetics, also, isotherm data was analyzed for possible agreement with the Langmuir and Freundlich adsorption isotherms, the Freundlich and Langmuir models for dynamics of metal ion uptake proposed in this work fitted the experimental data reasonably well. However, equilibrium sorption data were better represented by Langmuir model than Freundlich. The adsorption capacity calculated from Langmuir isotherm was 84.31, 76.23 and 59.63mgCr(VI)/g at initial pH of 3.0 at 30 degrees C for the particle size of 1.00-1.25mm with the use of 12.5, 16.5 and 2.1g/L of CACASC, CCASC and ACASC adsorbent mass, respectively. This readily available adsorbent is efficient in the uptake of Cr(VI) ion in aqueous solution, thus, it could be an excellent alternative for the removal of heavy metals and organic matter from water and wastewater. PMID:19022632

  8. Mechanism of highly efficient adsorption of 2-chlorophenol onto ultrasonic graphene materials: Comparison and equilibrium.

    PubMed

    Soltani, Tayyebeh; Lee, Byeong-Kyu

    2016-11-01

    The deficiencies of the recently reported improved Hummers method for the synthesis of graphene oxide (GO), such as high reaction temperature (60°C) and long reaction time (10h), were successfully solved using a low-intensity ultrasonic bath for 30min at 40°C. Furthermore, compared to its conventional synthesis counterpart, a facile and fast, one-step ultrasonic method that excluded hydrazine hydrate was developed to synthesize reduced GO (rGO) from graphite (10min, 50°C) in the presence of hydrazine hydrate (rGO-C, 12h, 90°C). The adsorption characteristics of 2-chlorophenol (2-CP) from an aqueous solution were investigated using rGOs and GOs prepared by ultrasonic (rGO-Us/GO-Us) and conventional (rGO-C/GO-C) methods. Whereas 2-CP was completely removed with rGO-Us after 50min, only 40% of 2-CP was eliminated with rGO-C. The maximum adsorption capacity of 2-CP calculated by the Langmuir model onto rGO-Us (208.67mg/g) was much higher than that onto GO-Us (134.49mg/g). In addition, the ultrasonic graphene adsorption capacities were much higher than the corresponding values of rGO-C (49.9mg/g) and GO-C (32.06mg/g). The enhanced adsorption for rGO-Us and GO-Us is attributed to their greater surface areas, excellent oxygenated groups for GO-Us and superior π-electron-rich matrix for rGO-Us, compared to other adsorbents. The adsorption of 2-CP on the rGO materials increased with increasing solution pH to a maximum around its pKa (pKa=8.85), while the adsorption for the GO materials increased with decreasing solution pH. The adsorption mechanism proceeded via hydrogen bonding in neutral and acidic media, but via π-π electron donor-accepter (EDA) interactions between 2-CP and graphene materials in basic medium. The FTIR spectrum of GO-Us after adsorption indicates that the position and intensity of many peaks of GO-Us were affected due to the adsorption of different 2-CP groups at different pHs. PMID:27474817

  9. Dynamic behaviour of Cd2+ adsorption in equilibrium batch studies by CaCO3(-)-rich Corbicula fluminea shell.

    PubMed

    Ismail, Farhah Amalya; Aris, Ahmad Zaharin; Latif, Puziah Abdul

    2014-01-01

    This work presents the structural and adsorption properties of the CaCO3(-)-rich Corbicula fluminea shell as a natural and economic adsorbent to remove Cd ions from aqueous solutions under batch studies. Experiments were conducted with different contact times, various initial concentrations, initial solution pH and serial biosorbent dosage to examine the dynamic characterization of the adsorption and its influence on Cd uptake capacity. The characterization of the C. fluminea shell using SEM/EDX revealed that the adsorbent surface is mostly impregnated by small particles of potentially calcium salts. The dominant Cd adsorption mechanism is strongly pH and concentration dependent. A maximum Cd removal efficiency of 96.20% was obtained at pH 7 while the optimum adsorbent dosage was observed as 5 g/L. The Langmuir isotherm was discovered to be more suitable to represent the experimental equilibrium isotherm results with higher correlation coefficients (R(2) > 0.98) than Freundlich (R(2) < 0.97).The correlation coefficient values (p < 0.01) indicated the superiority of the Langmuir isotherm over the Freundlich isotherm. PMID:23771443

  10. Adsorption of methylene blue onto activated carbon produced from tea (Camellia sinensis L.) seed shells: kinetics, equilibrium, and thermodynamics studies*

    PubMed Central

    Gao, Jun-jie; Qin, Ye-bo; Zhou, Tao; Cao, Dong-dong; Xu, Ping; Hochstetter, Danielle; Wang, Yue-fei

    2013-01-01

    Tea (Camellia sinensis L.) seed shells, the main byproduct of the manufacture of tea seed oil, were used as precursors for the preparation of tea activated carbon (TAC) in the present study. A high yield (44.1%) of TAC was obtained from tea seed shells via a one-step chemical method using ZnCl2 as an agent. The Brunauer-Emmett-Teller (BET) surface area and the total pore volumes of the obtained TAC were found to be 1 530.67 mg2/g and 0.782 6 cm3/g, respectively. The equilibrium adsorption results were complied with Langmuir isotherm model and its maximum monolayer adsorption capacity was 324.7 mg/g for methylene blue. Adsorption kinetics studies indicated that the pseudo-second-order model yielded the best fit for the kinetic data. An intraparticle diffusion model suggested that the intraparticle diffusion was not the only rate-controlling step. Thermodynamics studies revealed the spontaneous and exothermic nature of the sorption process. These results indicate that tea seed shells could be utilized as a renewable resource to develop activated carbon which is a potential adsorbent for methylene blue. PMID:23825151

  11. Kinetic and equilibrium characterization of uranium(VI) adsorption onto carboxylate-functionalized poly(hydroxyethylmethacrylate)-grafted lignocellulosics.

    PubMed

    Anirudhan, T S; Divya, L; Suchithra, P S

    2009-01-01

    This study investigated the feasibility of using a new adsorbent prepared from coconut coir pith, CP (a coir industry-based lignocellulosic residue), for the removal of uranium [U(VI)] from aqueous solutions. The adsorbent (PGCP-COOH) having a carboxylate functional group at the chain end was synthesized by grafting poly(hydroxyethylmethacrylate) onto CP using potassium peroxydisulphate-sodium thiosulphite as a redox initiator and in the presence of N,N'-methylenebisacrylamide as a crosslinking agent. IR spectroscopy results confirm the graft copolymer formation and carboxylate functionalization. XRD studies confirm the decrease of crystallinity in PGCP-COOH compared to CP, and it favors the protrusion of the functional group into the aqueous medium. The thermal stability of the samples was studied using thermogravimetry (TG). Surface charge density of the samples as a function of pH was determined using potentiometric titration. The ability of PGCP-COOH to remove U(VI) from aqueous solutions was assessed using a batch adsorption technique. The maximum adsorption capacity was observed at the pH range 4.0-6.0. Maximum removal of 99.2% was observed for an initial concentration of 25mg/L at pH 6.0 and an adsorbent dose of 2g/L. Equilibrium was achieved in approximately 3h. The experimental kinetic data were analyzed using a first-order kinetic model. The temperature dependence indicates an endothermic process. U(VI) adsorption was found to decrease with an increase in ionic strength due to the formation of outer-sphere surface complexes on PGCP-COOH. Equilibrium data were best modeled by the Langmuir isotherm. The thermodynamic parameters such as DeltaG(0), DeltaH(0) and DeltaS(0) were derived to predict the nature of adsorption. Adsorption experiments were also conducted using a commercial cation exchanger, Ceralite IRC-50, with carboxylate functionality for comparison. Utility of the adsorbent was tested by removing U(VI) from simulated nuclear industry wastewater

  12. Adsorption of heavy metal cations by Na-clinoptilolite: equilibrium and selectivity studies.

    PubMed

    Mihaly-Cozmuta, L; Mihaly-Cozmuta, A; Peter, A; Nicula, C; Tutu, H; Silipas, Dan; Indrea, Emil

    2014-05-01

    This paper summarizes the conclusions of experiments conducted on the adsorption of Cd(2+), Co(2+), Cu(2+), Mn(2+), Ni(2+), Pb(2+) and Zn(2+) onto zeolite. The focus of the experiments was to establish the influence of the initial pH of the contact solution as well as the selectivity of zeolite on the efficiency of the adsorption process. To this end, experimental adsorption isotherms were established for the pH values ranging from 1 to 4 by using the Na-form of clinoptilolite (particle size range 0.5-1 mm) as an adsorbent. Langmuir, Freundlich and Dubinin-Raduschkevich isotherm models were used to validate the experimental data and the Gibbs free energy was calculated based on the distribution coefficient. From the Langmuir model, correlations between the maximum adsorption capacity and selected physical-chemical parameters of the cations studied were established. The results of the experiments suggest that the selectivity of zeolite is strongly influenced by the pH of the contact solution, dehydration energy of cations, diffusion coefficient and the pH at which the precipitation of hydroxides occurs. PMID:24603029

  13. Equilibrium study of selected divalent d-electron metals adsorption on A-type zeolite.

    PubMed

    Majdan, Marek; Pikus, Stanisław; Kowalska-Ternes, Monika; Głdysz-Płaska, Agnieszka; Staszczuk, Piotr; Fuks, Leon; Skrzypek, Henryk

    2003-06-15

    The objective of the presented study was to investigate the adsorption of Cu, Co, Mn, Zn, Cd and Mn on A-type zeolite. The isotherms for adsorption of metals from their nitrates were registered. The following adsorption constants K of metals were found: 162,890, 124,260, 69,025, 16,035, 10,254, and 151 [M(-1)] for Cu, Co, Mn, Zn, Cd, and Ni, respectively, for the concentration range 10(-4)-10(-3) M. On the other hand, the investigation of pH influence on the distribution constants of metals showed that the adsorption of metals proceeds essentially through an ion-exchange process, surface hydrolysis, and surface complexation. The supplementary results from DRIFT, scanning electron microscopy, and X-ray diffraction methods confirmed the presumption about the possible connection between the electronic structure of divalent ions and their adsorption behavior, showing that ions with d5 and d10 configurations such as Mn2+, Zn2+, Cd2+, with much weaker hydrolytic properties than Cu2+ and Ni2+, strongly interact with the zeolite framework and therefore their affinity to the zeolite phase is much stronger when compared with that of the Ni2+ ion, but at the same time not as strong as the affinity of the Cu2+ ion, the latter forming a new phase during the interaction with zeolite framework. For Zn2+, during inspection of the correlation between the proton concentration H/Al and zinc concentration Zn/Al on the zeolite surface, the formation of the surface complex [triple bond]S-OZn(OH) was proposed. A correlation between the heterogeneity of proton concentrations H/Al on Me-zeolite surfaces and the hydrolysis constants pKh of Me2+ ions was found. PMID:16256612

  14. Removal of azo dye by a highly graphitized and heteroatom doped carbon derived from fish waste: Adsorption equilibrium and kinetics.

    PubMed

    Liu, Zhengang; Zhang, Fang; Liu, Tingting; Peng, Nana; Gai, Chao

    2016-11-01

    A highly graphitized and heteroatom doped porous carbon was prepared from fish waste in the present study. The morphology and chemical composition of the resultant porous carbon were characterized by SEM-EDS, TEM, BET, XRD and Raman measurement. The prepared porous carbon was employed as an adsorbent for acid orange 7, a typical azo dye, removal from aqueous solution. The results showed that the porous carbon had ultrahigh surface area of 2146 m(2)/g, a high degree of graphitization structure and naturally doped with nitrogen and phosphorous. The maximum adsorption capacity of acid orange 7 reached 285.71 mg/g due to unique property of the prepared porous carbon. In addition, acid orange 7 adsorption onto the porous carbon well followed pseudo-second-order kinetics model and acid orange 7 diffusion in micropores was the potential rate controlling step. PMID:27526082

  15. Three model space experiments on chemical reactions. [Gibbs adsorption, equilibrium shift and electrodeposition

    NASA Technical Reports Server (NTRS)

    Grodzka, P.; Facemire, B.

    1977-01-01

    Three investigations conducted aboard Skylab IV and Apollo-Soyuz involved phenomena that are of interest to the biochemistry community. The formaldehyde clock reaction and the equilibrium shift reaction experiments conducted aboard Apollo Soyuz demonstrate the effect of low-g foams or air/liquid dispersions on reaction rate and chemical equilibrium. The electrodeposition reaction experiment conducted aboard Skylab IV demonstrate the effect of a low-g environment on an electrochemical displacement reaction. The implications of the three space experiments for various applications are considered.

  16. Adsorptive potential of cationic Basic Yellow 2 (BY2) dye onto natural untreated clay (NUC) from aqueous phase: Mass transfer analysis, kinetic and equilibrium profile

    NASA Astrophysics Data System (ADS)

    Öztürk, A.; Malkoc, E.

    2014-04-01

    In this work, natural untreated clay (NUC) was studied for the removal of Basic Yellow 2 (BY2) from aqueous solution in batch system. The effects of initial BY2 concentration, contact time, solution temperature and solution pH on BY2 adsorption were investigated. Nitrogen sorption measurements were employed to investigate the variation in surface and pore properties after dye adsorption. The adsorbent was characterized by means of FTIR, PSD, TEM, XRD and BET analysis. The equilibrium adsorption data were analyzed by Langmuir, Freundlich, Temkin and Scatchard isotherm models. The maximum monolayer adsorption capacity was found to be 833.33 mg/g at 25 °C (at room temperature). The pseudo-second-order kinetic model provided the best fit to the experimental datas compared with pseudo-first-order kinetic adsorption models. To explain mass transfer mechanism of BY2 adsorption, obtained experimental datas were applied Weber and Morris model, Body and Frusawa and Smith models. The results show that the adsorption process is controlled by film diffusion. The thermodynamic parameters such as, Gibbs free energy changes (ΔG°), standard enthalpy change (ΔH°) and standard entropy change (ΔS°) were determined. Adsorption of BY2 on NUC is exothermic and spontaneous in nature. The calculated activation energy of adsorption was found to be 5.24 kJ/mol for BY2. This value indicates that the adsorption process is a physisorption.

  17. Protein loading into porous CaCO3 microspheres: adsorption equilibrium and bioactivity retention.

    PubMed

    Balabushevich, N G; Lopez de Guerenu, A V; Feoktistova, N A; Volodkin, D

    2015-01-28

    Formulation of proteins into particulate form is a principal strategy to achieve controlled and targeted delivery, as well as to protect fragile protein molecules. Control over size, mechanical properties, and surface area (porosity) of particulate proteins has been successfully achieved by hard templating under mild conditions using porous CaCO3 microspheres. A crucial step in this approach, which determines protein content, is the loading of proteins into the CaCO3 microspheres. In this study, the adsorption of different proteins into the microspheres has been investigated. Proteins differing in characteristics such as molecular weight and charge have been employed: catalase (Cat), insulin (Ins), aprotinin (Apr), and protamine (Pro). Thermodynamics of adsorption equilibria have been studied, together with quantitative and qualitative analysis of protein loading and distribution in the microspheres. Protein interaction with the CaCO3 microspheres is not limited by the diffusion of protein molecules (protein dimensions are significantly smaller than microsphere pores) but is determined by the protein affinity for the microsphere surface. Cat and Ins bind much more strongly to the microspheres than Apr and Pro, which can be explained by electrostatic attractive forces. Protein binding/release and protein biological activity have been investigated as a function of pH. It is shown that pH variation during the adsorption process plays a principal role and defines not only the amount of protein adsorbed/released but also protein biological activity. Protein adsorption and microsphere elimination (by EDTA) do not affect protein bioactivity. In addition to applications for protein particle/capsule formulations, the findings of this study might help in understanding protein interactions with carbonate minerals such as calcium carbonate, which is used as a natural material for multiple applications. PMID:25493351

  18. Kinetic, equilibrium and thermodynamic studies of cadmium (II) adsorption by modified agricultural wastes.

    PubMed

    Othman, Zeid A Al; Hashem, Ali; Habila, Mohamed A

    2011-01-01

    Agricultural wastes have great potential for the removal of heavy metal ions from aqueous solution. The contamination of water by toxic heavy metals is a worldwide environmental problem. Unlike organic pollutants, the majority of which are susceptible to biological degradation, heavy metals do not degrade into harmless end products. Discharges containing cadmium, in particular, are strictly controlled because of the highly toxic nature of this element and its tendency to accumulate in the tissues of living organisms. This work aims to develop inexpensive, highly available, effective metal ion adsorbents from natural wastes as alternatives to existing commercial adsorbents. In particular, Tamrix articulata wastes were modified chemically by esterification with maleic acid to yield a carboxyl-rich adsorbent. The adsorption behavior of treated Tamrix articulata wastes toward cadmium ions in aqueous solutions in a batch system has been studied as a function of equilibration time, adsorbent dose, temperature and pH. Results showed that the maximum adsorption capacity was 195.5 mg/g in a pH 4 solution at 30 °C with a contact time of 120 min, an initial concentration of 400 mg/L and an adsorbent dose of 0.3 g/L. The kinetic data were analyzed using pseudo-first-order and pseudo-second-order kinetic models. It was shown that the adsorption of cadmium could be described by a pseudo-second-order equation. The experimental data were also analyzed using the Langmuir and Freundlich models of adsorption. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° have been evaluated and it has been found that the sorption process was spontaneous and exothermic in nature. From all of our data, we conclude that the treated Tamrix articulata wastes investigated in this study showed good potential for cadmium removal from aqueous solutions. PMID:22173337

  19. Hydrous ferric oxide doped alginate beads for fluoride removal: Adsorption kinetics and equilibrium studies

    NASA Astrophysics Data System (ADS)

    Sujana, M. G.; Mishra, A.; Acharya, B. C.

    2013-04-01

    A new biopolymer beads, composite of hydrous ferric oxide (HFO) and alginate were synthesised, characterised and studied for its fluoride efficiency from water. The beads were characterised by chemical analysis, BET surface area, pHPZC and X-ray diffraction (XRD) analysis. The optimum conditions for fluoride removal were determined by studying operational variables viz. pH, contact time, initial F- concentration, bead dose and temperature. Presence of other anions like SO42-, PO43-, NO3-, Cl- and HCO3- effect on fluoride removal efficiency of prepared beads was also tested. The beads were 0.8-0.9 mm in size and contain 32-33% Fe (III) and showed specific surface area of 25.80 m2 g-1 and pHPZC of 5.15. Modified beads demonstrated Langmuir F- adsorption capacity of 8.90 mg g-1 at pH 7.0. The adsorption kinetics were best described by the pseudo-second order kinetic model followed by intra-particle diffusion as the rate determining step. It was found that about 80% of the adsorbed fluoride could be desorbed by using 0.05 M HCl. The FTIR, Raman and SEM-EDAX analysis were used to study the fluoride adsorption mechanisms on beads. Studies were also conducted to test the potential application of beads for F- removal from drinking water and the treated water quality.

  20. Effect of the adsorbate (Bromacil) equilibrium concentration in water on its adsorption on powdered activated carbon. Part 2: Kinetic parameters.

    PubMed

    Al Mardini, Fadi; Legube, Bernard

    2009-10-30

    The application of several monosolute equilibrium models has previously shown that Bromacil adsorption on SA-UF (Norit) powdered activated carbon (PAC) is probably effective on two types of sites. High reactivity sites were found to be 10-20 less present in a carbon surface than lower reactivity sites, according to the q(m) values calculated by isotherm models. The aims of this work were trying, primarily, to identify the kinetic-determinant stage of the sorption of Bromacil at a wide range of initial pesticide concentrations (approximately 5 to approximately 500 microg L(-1) at pH 7.8), and secondly, to specify the rate constants and other useful design parameters for the application in water treatment. It was therefore not possible to specify a priori whether the diffusion or surface reaction is the key step. It shows that many of the tested models which describe the stage of distribution or the surface reaction are correctly applied. However, the diffusivity values (D and D(0)) were found to be constant only constants for some specific experimental concentrations. The HSDM model of surface diffusion in pores was also applied but the values of the diffusion coefficient of surface (D(s)) were widely scattered and reduce significantly with the initial concentration or the equilibrium concentration in Bromacil. The model of surface reaction of pseudo-second order fitted particularly well and led to constant values which are independent of the equilibrium concentration, except for the low concentrations where the constants become significantly more important. This last observation confirms perfectly the hypothesis based on two types of sites as concluded by the equilibrium data (part 1). PMID:19560269

  1. Characterizing particle-scale equilibrium adsorption and kinetics of uranium(VI) desorption from U-contaminated sediments

    USGS Publications Warehouse

    Stoliker, Deborah L.; Liu, Chongxuan; Kent, Douglas B.; Zachara, John M.

    2013-01-01

    Rates of U(VI) release from individual dry-sieved size fractions of a field-aggregated, field-contaminated composite sediment from the seasonally saturated lower vadose zone of the Hanford 300-Area were examined in flow-through reactors to maintain quasi-constant chemical conditions. The principal source of variability in equilibrium U(VI) adsorption properties of the various size fractions was the impact of variable chemistry on adsorption. This source of variability was represented using surface complexation models (SCMs) with different stoichiometric coefficients with respect to hydrogen ion and carbonate concentrations for the different size fractions. A reactive transport model incorporating equilibrium expressions for cation exchange and calcite dissolution, along with rate expressions for aerobic respiration and silica dissolution, described the temporal evolution of solute concentrations observed during the flow-through reactor experiments. Kinetic U(VI) desorption was well described using a multirate SCM with an assumed lognormal distribution for the mass-transfer rate coefficients. The estimated mean and standard deviation of the rate coefficients were the same for all <2 mm size fractions but differed for the 2–8 mm size fraction. Micropore volumes, assessed using t-plots to analyze N2 desorption data, were also the same for all dry-sieved <2 mm size fractions, indicating a link between micropore volumes and mass-transfer rate properties. Pore volumes for dry-sieved size fractions exceeded values for the corresponding wet-sieved fractions. We hypothesize that repeated field wetting and drying cycles lead to the formation of aggregates and/or coatings containing (micro)pore networks which provided an additional mass-transfer resistance over that associated with individual particles. The 2–8 mm fraction exhibited a larger average and standard deviation in the distribution of mass-transfer rate coefficients, possibly caused by the abundance of

  2. Dynamic, equilibrium and human studies of adsorption of 201Tl by Prussian blue.

    PubMed

    Bhardwaj, Nidhi; Bhatnagar, Aseem; Pathak, D P; Singh, A K

    2006-03-01

    Prussian blue is the recommended but infrequently required antidote for radiocesium and thallium chemical poisoning. Conceivably, its most frequent application will be the decontamination of radiothallium (thallous chloride) from human body following myocardial scintigraphy. Dosage schedule and physicochemical parameters of interaction with radiothallium, however, need to be defined, as the known data is inadequate on this account. The objective of the present study is to create physiologically relevant and mathematically rigorous data on interaction of Prussian blue with Tl, to estimate dosage schedule of Prussian blue suitable for myocardial scintigraphy, and to perform preliminary human studies to evaluate the efficacy of the antidote in reducing the considerable radiation burden imparted by this radiotracer. Adsorption efficacy of Prussian blue for radiothallium was found to be more than 95% at basic (intestinal) pH even at low concentrations and in presence of the physiological cations, potassium and sodium. Isotherm analysis and derivations using Langmuir, Bajpai, Lagergreen, and Freundlich equations suggest a favorable adsorption of Tl on Prussian blue with qmax being 5,000 MBq g. Based on these findings and clinical considerations, particularly preferential gall bladder excretion and enterohepatic recycling of radioactive thallous chloride, a dose of 100 mg Prussian blue with every major meal for 3 days was considered adequate for the purpose. Our experience with the first two patients (serving as their own self-controls) suggests that Prussian blue therapy is a safe and effective method to significantly reduce radiation burden imparted by thallium myocardial scintigraphy. PMID:16505622

  3. Arsenic (III) adsorption on iron acetate coated activated alumina: thermodynamic, kinetics and equilibrium approach

    PubMed Central

    2013-01-01

    The adsorption potential of iron acetate coated activated alumina (IACAA) for removal of arsenic [As (III)] as arsenite by batch sorption technique is described. IACAA was characterized by XRD, FTIR, EDAX and SEM instruments. Percentage adsorption on IACAA was determined as a function of pH, contact time and adsorbent dose. The study revealed that the removal of As (III) was best achieved at pH =7.4. The initial As (III) concentration (0.45 mg/L) came down to less than 0.01 mg/L at contact time 90 min with adsorbent dose of 1 g/100 mL. The sorption was reasonably explained with Langmuir and Freundlich isotherms. The thermodynamic parameters such as ΔG 0 , ΔH 0 , ΔS 0 and E a were calculated in order to understand the nature of sorption process. The sorption process was found to be controlled by pseudo-second order and intraparticle diffusion models. PMID:24359995

  4. Equilibrium and kinetic models on the adsorption of Reactive Black 5 from aqueous solution using Eichhornia crassipes/chitosan composite.

    PubMed

    El-Zawahry, Manal M; Abdelghaffar, Fatma; Abdelghaffar, Rehab A; Hassabo, Ahmed G

    2016-01-20

    New natural biopolymer composite was prepared using extracted cellulose from an environmentally problematic water hyacinth Eichhornia crassipes (EC). The extracted cellulose was functionalized by chitosan and TiO2 nanoparticles to form EC/Chitosan (EC/Cs) composite network. Surface characterization of EC/Cs natural biopolymer composite was examined by spectrum analysis FT-IR, specific surface area, micropore volume, pore width and SEM. Furthermore, the sorption experiments were carried out as a function of pH, various initial dye concentration and contact time. Experiment results showed that the EC/Cs composite have high ability to remove C.I. Reactive Black 5 from its dye-bath effluent. The equilibrium sorption evaluation of RB5 conformed and fitted well to Langmuir adsorption isotherm models and the maximum sorption capacity was 0.606 mg/g. The kinetic adsorption models followed pseudo-second order model and the dye intra-particle diffusion may suggesting a chemical reaction mechanism. Further, it was obvious from the investigation that this composite could be applied as a promising low cost adsorbent for anionic dye removal from aqueous solutions. PMID:26572382

  5. Adsorption of geosmin and 2-methylisoborneol onto powdered activated carbon at non-equilibrium conditions: influence of NOM and process modelling.

    PubMed

    Zoschke, Kristin; Engel, Christina; Börnick, Hilmar; Worch, Eckhard

    2011-10-01

    The adsorption of the taste and odour (T&O) compounds geosmin and 2-methylisoborneol (2-MIB) onto powdered activated carbon (PAC) has been studied under conditions which are typical for a drinking water treatment plant that uses reservoir water for drinking water production. The reservoir water as well as the pre-treated water (after flocculation) contains NOM that competes with the trace compounds for the adsorption sites on the carbon surface. Although the DOC concentrations in the reservoir water and in the pre-treated water were different, no differences in the competitive adsorption could be seen. By using two special characterisation methods for NOM (adsorption analysis, LC/OCD) it could be proved that flocculation removes only NOM fractions which are irrelevant for competitive adsorption. Different model approaches were applied to describe the competitive adsorption of the T&O compounds and NOM, the tracer model, the equivalent background compound model, and the simplified equivalent background compound model. All these models are equilibrium models but in practice the contact time in flow-through reactors is typically shorter than the time needed to establish the adsorption equilibrium. In this paper it is demonstrated that the established model approaches can be used to describe competitive adsorption of T&O compounds and NOM also under non-equilibrium conditions. The results of the model applications showed that in particular the simplified equivalent background compound model is a useful tool to determine the PAC dosage required to reduce the T&O compounds below the threshold concentration. PMID:21752419

  6. Adsorption of Pb(II) ions onto biomass from Trifolium resupinatum: equilibrium and kinetic studies

    NASA Astrophysics Data System (ADS)

    Athar, Makshoof; Farooq, Umar; Aslam, Muhammad; Salman, M.

    2013-09-01

    The present study provides information about the binding of Pb(II) ions on an eco-friendly and easily available biodegradable biomass Trifolium resupinatum. The powdered biomass was characterized by FTIR, potentiometric titration and surface area analyses. The FTIR spectrum showed the presence of hydroxyl, carbonyl and amino functional groups and Pb(II) ions bound with the oxygen- and nitrogen-containing sites (hydroxyl and amino groups). The acidic groups were also confirmed by titrations. Effects of various environmental parameters (time, pH and concentration) have been studied. The biosorption process achieved equilibrium in a very short period of time (25 min). Non-linear approach for Langmuir and Freundlich models was used to study equilibrium process and root mean-square error was used as an indicator to decide the fitness of the mathematical model. The biosorption process was found to follow pseudo-second-order kinetics and was very fast. Thus, the biomass can be cost-effectively used for the binding of Pb(II) ions from aqueous solutions.

  7. On the 2D-transition, hysteresis and thermodynamic equilibrium of Kr adsorption on a graphite surface.

    PubMed

    Diao, Rui; Fan, Chunyan; Do, D D; Nicholson, D

    2015-12-15

    The adsorption and desorption of Kr on graphite at temperatures in the range 60-88K, was systematically investigated using a combination of several simulation techniques including: Grand Canonical Monte Carlo (GCMC), Canonical kinetic-Monte Carlo (C-kMC) and the Mid-Density Scheme (MDS). Particular emphasis was placed on the gas-solid, gas-liquid and liquid-solid 2D phase transitions. For temperatures below the bulk triple point, the transition from a 2D-liquid-like monolayer to a 2D-solid-like state is manifested as a sub-step in the isotherm. A further increase in the chemical potential leads to another rearrangement of the 2D-solid-like state from a disordered structure to an ordered structure that is signalled by (1) another sub-step in the monolayer region and (2) a spike in the plot of the isosteric heat versus density at loadings close to the dense monolayer coverage concentration. Whenever a 2D transition occurs in a grand canonical isotherm it is always associated with a hysteresis, a feature that is not widely recognised in the literature. We studied in details this hysteresis with the analysis of the canonical isotherm, obtained with C-kMC, which exhibits a van der Waals (vdW) type loop with a vertical segment in the middle. We complemented the hysteresis loop and the vdW curve with the analysis of the equilibrium transition obtained with the MDS, and found that the equilibrium transition coincides exactly with the vertical segment of the C-kMC isotherm, indicating the co-existence of two phases at equilibrium. We also analysed adsorption at higher layers and found that the 2D-coexistence is also observed, provided that the temperature is well below the triple point. Finally the 2D-critical temperatures were obtained for the first three layers and they are in good agreement with the experimental data in the literature. PMID:26364074

  8. Simulating adsorption of U(VI) under transient groundwater flow and hydrochemistry – Physical versus non-equilibrium model

    SciTech Connect

    Greskowiak, Janek; Hay, Michael B.; Prommer, Henning; Liu, Chongxuan; Post, Vincent; Ma, Rui; Davis, James A.; Zheng, Chunmiao; Zachara, John M.

    2011-08-03

    Coupled intra-grain diffusional mass-transfer and non-linear surface complexation processes play an important role for the transport behaviour of U(VI) in contaminated aquifers. Two alternative model approaches for simulating these coupled processes have been analysed and compared: (i) the physical non-equilibrium approach that explicitly accounts for aqueous speciation and instantaneous surface complexation reactions in the intra-grain regions and approximates the diffusive mass exchange between the immobile intra-grain pore water and the advective pore water as multi-rate 1st-order mass transfer and (ii) the chemical non-equilibrium approach that approximates the diffusion-limited intra-grain surface complexation reactions by a set of multiple 1st-order surface complexation reaction kinetics, thereby eliminating the explicit treatment of aqueous speciation in the intra grain pore water. Model comparison has been carried out for column and field scale scenarios, representing the highly transient hydrological and geochemical conditions in the U(VI)-contaminated aquifer at the Hanford 300A site, Washington, USA. It was found that the response of apparent U(VI) adsorption/desorption kinetic behaviour to hydrogeochemically induced changes in U(VI) sorption strength is more pronounced in the physical than in the chemical non-equilibrium model. The magnitude of the differences in model behaviour depends particularly on the degree of disequilibrium between the advective and immobile phase U(VI) concentrations. While a clear difference in U(VI) transport behaviour between the two models was noticeable for the column-scale scenarios, only minor differences were found for the Hanford 300A field scale scenarios, where the model-generated disequilibrium conditions were less pronounced as a result of high frequent groundwater flow reversals.

  9. Effect of the adsorbate (Bromacil) equilibrium concentration in water on its adsorption on powdered activated carbon. Part 3: Competition with natural organic matter.

    PubMed

    Al Mardini, Fadi; Legube, Bernard

    2010-10-15

    This study (part 3) was carried out to investigate the effect of the natural organic matter (NOM) concentration on Bromacil (pesticide) adsorption on powdered activated carbon (PAC) in the same experimental conditions as in our previous studies (parts 1 and 2). Our previous findings showed that Bromacil adsorption in buffered pure water (pH 7.8) occurred at two types of site. In the presence of NOM (three kinds), we noted a significant reduction in Bromacil adsorption capacities due to the competitive effects exerted by NOM. Highly reactive sites (or pores) in PAC appeared to be blocked by NOM adsorption, as demonstrated by the application of a pseudo-single solute isotherm and of the simplified ideal adsorbed solution theory (IAST), regardless of the initial Bromacil and NOM concentrations. The competing effect of low-molecular weight NOM was found to be greater than the competing effect of high-molecular weight NOM. The pseudo-second order surface-reaction model fitted Bromacil adsorption particularly well, even in the presence of NOM. However, the adsorption-kinetic constant values were found to be independent of the aqueous equilibrium concentration of the target compound, contrary to that observed in pure water. The kinetic data thus confirmed that high reactivity PAC sites were blocked by NOM adsorption. A practical approach concluded this work. PMID:20619963

  10. Enhanced adsorptive removal of Safranine T from aqueous solutions by waste sea buckthorn branch powder modified with dopamine: Kinetics, equilibrium, and thermodynamics

    NASA Astrophysics Data System (ADS)

    Xu, Xiaohui; Bai, Bo; Wang, Honglun; Suo, Yourui

    2015-12-01

    Polydopamine coated sea buckthorn branch powder (PDA@SBP) was facilely synthesized via a one-pot bio-inspired dip-coating approach. The as-synthesized PDA@SBP was characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The adsorption progresses of Safranine T on the surface of PDA@SBP adsorbent were systematically investigated. More specifically, the effects of solution pH, contact time, initial concentration and temperature were evaluated, respectively. The experimental results showed the adsorption capacity of PDA@SBP at 293.15 K could reach up to 54.0 mg/g; the adsorption increased by 201.7% compared to that of native SBP (17.9 mg/g). Besides, kinetics studies showed that pseudo-second-order kinetic model adequately described the adsorption behavior. The adsorption experimental data could be fitted well a Freundlich isotherm model. Thermodynamic analyses showed that the ST adsorption was a physisorption endothermic process. Regeneration of the spent PDA@SBP adsorbent was conducted with 0.1 M HCl without significant reduction in adsorption capacity. On the basis of these investigations, it is believed that the PDA@SBP adsorbent could have potential applications in sewage disposal areas because of their considerable adsorption capacities, brilliant regeneration capability, and cost-effective and eco-friendly preparation and use.

  11. Lysozyme adsorption in pH-responsive hydrogel thin-films: the non-trivial role of acid-base equilibrium.

    PubMed

    Narambuena, Claudio F; Longo, Gabriel S; Szleifer, Igal

    2015-09-01

    We develop and apply a molecular theory to study the adsorption of lysozyme on weak polyacid hydrogel films. The theory explicitly accounts for the conformation of the network, the structure of the proteins, the size and shape of all the molecular species, their interactions as well as the chemical equilibrium of each titratable unit of both the protein and the polymer network. The driving forces for adsorption are the electrostatic attractions between the negatively charged network and the positively charged protein. The adsorption is a non-monotonic function of the solution pH, with a maximum in the region between pH 8 and 9 depending on the salt concentration of the solution. The non-monotonic adsorption is the result of increasing negative charge of the network with pH, while the positive charge of the protein decreases. At low pH the network is roughly electroneutral, while at sufficiently high pH the protein is negatively charged. Upon adsorption, the acid-base equilibrium of the different amino acids of the protein shifts in a nontrivial fashion that depends critically on the particular kind of residue and solution composition. Thus, the proteins regulate their charge and enhance adsorption under a wide range of conditions. In particular, adsorption is predicted above the protein isoelectric point where both the solution lysozyme and the polymer network are negatively charged. This behavior occurs because the pH in the interior of the gel is significantly lower than that in the bulk solution and it is also regulated by the adsorption of the protein in order to optimize protein-gel interactions. Under high pH conditions we predict that the protein changes its charge from negative in the solution to positive within the gel. The change occurs within a few nanometers at the interface of the hydrogel film. Our predictions show the non-trivial interplay between acid-base equilibrium, physical interactions and molecular organization under nanoconfined conditions

  12. Uptake of gaseous formaldehyde by soil surfaces: a combination of adsorption/desorption equilibrium and chemical reactions

    NASA Astrophysics Data System (ADS)

    Li, Guo; Su, Hang; Li, Xin; Kuhn, Uwe; Meusel, Hannah; Hoffmann, Thorsten; Ammann, Markus; Pöschl, Ulrich; Shao, Min; Cheng, Yafang

    2016-08-01

    Gaseous formaldehyde (HCHO) is an important precursor of OH radicals and a key intermediate molecule in the oxidation of atmospheric volatile organic compounds (VOCs). Budget analyses reveal large discrepancies between modeled and observed HCHO concentrations in the atmosphere. Here, we investigate the interactions of gaseous HCHO with soil surfaces through coated-wall flow tube experiments applying atmospherically relevant HCHO concentrations of ˜ 10 to 40 ppbv. For the determination of uptake coefficients (γ), we provide a Matlab code to account for the diffusion correction under laminar flow conditions. Under dry conditions (relative humidity = 0 %), an initial γ of (1.1 ± 0.05) × 10-4 is determined, which gradually drops to (5.5 ± 0.4) × 10-5 after 8 h experiments. Experiments under wet conditions show a smaller γ that drops faster over time until reaching a plateau. The drop of γ with increasing relative humidity as well as the drop over time can be explained by the adsorption theory in which high surface coverage leads to a reduced uptake rate. The fact that γ stabilizes at a non-zero plateau suggests the involvement of irreversible chemical reactions. Further back-flushing experiments show that two-thirds of the adsorbed HCHO can be re-emitted into the gas phase while the residual is retained by the soil. This partial reversibility confirms that HCHO uptake by soil is a complex process involving both adsorption/desorption and chemical reactions which must be considered in trace gas exchange (emission or deposition) at the atmosphere-soil interface. Our results suggest that soil and soil-derived airborne particles can either act as a source or a sink for HCHO, depending on ambient conditions and HCHO concentrations.

  13. A novel polar-modified post-cross-linked resin and its enhanced adsorption to salicylic acid: Equilibrium, kinetics and breakthrough studies.

    PubMed

    Wang, Xiaomei; Li, Guoqiang; Guo, Deping; Zhang, Yaling; Huang, Jianhan

    2016-05-15

    Improving the surface polarity is of significance for the post-cross-linked resins to enhance their adsorption to polar aromatic compounds. In the present study, we prepared a novel polar-modified post-cross-linked PDEpc_D by the Friedel-Crafts alkylation reaction and the amination reaction, the Brunauer-Emmett-Teller (BET) surface area and pore volume increased significantly after the Friedel-Crafts alkylation reaction and the surface polarity improved greatly after the amination reaction. Batch adsorption showed that PDEpc_D possessed a much enhanced adsorption to salicylic acid as compared the precursors PDE and PDEpc as well as the non-polar post-cross-linked PDVBpc. The equilibrium data was characterized by the Freundlich model, π-π stacking, hydrogen bonding and static interaction were the possible driving forces. The adsorption was a fast process and the kinetic data obeyed the micropore diffusion model. Column adsorption-desorption experiments suggested that PDEpc_D was a potential candidate for adsorptive removal of salicylic acid from aqueous solution. PMID:26928058

  14. Kinetics, equilibrium and thermodynamics of adsorption of 2-biphenylamine and dibenzylamine from aqueous solutions by Fe3O4/bentonite nanocomposite

    NASA Astrophysics Data System (ADS)

    Vasheghani F., B.; Rajabi, F. H.; Omidi, M. H.; Shabanian, S.

    2015-05-01

    Magnetic Fe3O4/bentonite nanocomposite is synthesized by chemical co-precipitation method. Experimental data are modelled by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherms. Freundlich and Langmuir isotherm model fitted the equilibrium data for the dibenzylamine (DBA) and 2-biphenylamine (BPA) respectively, compared to the other isotherm models. The calculated thermodynamic parameters, Δ G°, Δ H°, and Δ S° showed that the DBA and BPA adsorption on bentonite nanocomposite is spontaneous and endothermic under examined conditions. Experimental data were also modeled using the adsorption kinetic models. The results show that the adsorption processes of DBA and BPA followed well the pseudo-second-order kinetics. Results indicated that Fe3O4/bentonite nanocomposite could be an alternative for more costly adsorbents used for organic toxicants removal.

  15. A simple simulation of adsorption equilibrium of Pb(II) on Andosols in the presence of dissolved humic substances for monitoring soil contamination.

    PubMed

    Liu, Yuyu; Kobayashi, Takeshi; Takahashi, Yukari; Kameya, Takashi; Urano, Kohei

    2013-01-01

    The adsorption equilibrium of Pb(II) on Andosols was investigated and described quantitatively in order to develop a simple method for the rapid monitoring of heavy metals in soils. The effect of solution pH on adsorption isotherms was investigated experimentally and in simulations. At pH 7, the considerable desorption of Pb(II) due to the extensive dissolution of humic substances (HS) from soils into aqueous phases is known to be an obstacle to carrying out simulations. In batch experiments, the total organic carbon (TOC) of the aqueous phases was shown to be enhanced by the addition of pre-extracted HS to soil suspensions. By combining the ion-exchange and Freundlich models, the adsorption equilibriums of free Pb(2+) ions and Pb(2+)-HS were simulated and were shown to be in good agreement with the experimental results. By estimating the concentrations and adsorption amounts of Pb(2+) and Pb(2+)-HS from measured CPb and TOC, it is possible to accurately simulate the soil contamination status even in in the presence of dissolved HS in the water in the solid-liquid extraction samples. PMID:23947708

  16. Adsorptive removal of 2-chlorophenol by low-cost coir pith carbon.

    PubMed

    Namasivayam, C; Kavitha, D

    2003-03-17

    Adsorption of 2-chlorophenol (2-CP) by coir pith carbon was carried out by varying the parameters such as agitation time, 2-CP concentration, adsorbent dose, pH and temperature. Adsorption equilibrium reached at 40, 60, 80 and 100 min for 2-CP concentration of 10, 20, 30 and 40 mg/l, respectively. Adsorption followed second-order kinetics. The adsorption equilibrium data obeyed Freundlich isotherm. Acidic pH was favorable for the adsorption of 2-CP. Desorption studies showed that chemisorption plays a major role in the adsorption process. PMID:12628792

  17. Equilibrium and kinetics study on the adsorption of perfluorooctanoic acid from aqueous solution onto powdered activated carbon.

    PubMed

    Qu, Yan; Zhang, Chaojie; Li, Fei; Bo, Xiaowen; Liu, Guangfu; Zhou, Qi

    2009-09-30

    Powdered activated carbon (PAC) was applied to remove perfluorooctanoic acid (PFOA) from the aqueous PFOA solution in this study. Contact time, adsorbent dose and temperature were analyzed as the effect factors in the adsorption reaction. The contact time of maximum PFOA uptake was around 1h while the sorption removal efficiency increased with the PAC concentrations. And the process of adsorption increased from 303 K to 313 K and then decreased from 313 K to 323 K. Among four applied models, the experimental isotherm data were discovered to follow Langmuir isotherm model more closely. Thermodynamically, adsorption was endothermic because enthalpy, entropy and Gibbs constants were 198.5 kJ/mol, 0.709 kJ/mol/K and negative, respectively, which also indicated that the adsorption process was spontaneous and feasible. From kinetic analysis, the adsorption was suggested to be pseudo-second-order model. The adsorption of PFOA on the PAC was mainly controlled by particle diffusion. PMID:19395160

  18. Polar modified post-cross-linked resin and its adsorption toward salicylic acid from aqueous solution: Equilibrium, kinetics and breakthrough studies.

    PubMed

    Fu, Zhenyu; He, Chunlian; Huang, Jianhan; Liu, You-Nian

    2015-08-01

    A novel polar modified post-cross-linked resin PDMPA was synthesized, characterized and evaluated for adsorption of salicylic acid from aqueous solution. PDMPA was prepared by a suspension polymerization of methyl acrylate (MA) and divinylbenzene (DVB), a Friedel-Crafts reaction and an amination reaction. After characterization of the chemical and pore structure of PDMPA, the adsorption behaviors of salicylic acid on PDMPA were determined in comparison with the precursor resins. The equilibrium adsorption capacity of salicylic acid on PDMPA was much larger than the precursor resins and the equilibrium data were correlated by both of the Langmuir and Freundlich models. The pseudo-second-order rate equation fitted the kinetic data better than the pseudo-first-order rate equation, and the micropore diffusion model could characterize the kinetic data very well. The dynamic experimental results showed that the breakthrough point and saturated point of salicylic acid on PDMPA were 40.3 and 92.4BV (1BV=10mL) at a feed concentration of 995.8mg/L and a flow rate of 1.4mL/min, and the resin column could be regenerated by 16.0BV of a mixture desorption solvent containing 0.01mol/L of NaOH (w/v) and 50% of ethanol (v/v). PMID:25863446

  19. Adsorption/desorption of Cd(II), Cu(II) and Pb(II) using chemically modified orange peel: Equilibrium and kinetic studies

    NASA Astrophysics Data System (ADS)

    Lasheen, Mohamed R.; Ammar, Nabila S.; Ibrahim, Hanan S.

    2012-02-01

    Waste materials from industries such as food processing may act as cost effective and efficient biosorbents to remove toxic contaminants from wastewater. This study aimed to establish an optimized condition and closed loop application of processed orange peel for metals removal. A comparative study of the adsorption capacity of the chemically modified orange peel was performed against environmentally problematic metal ions, namely, Cd 2+, Cu 2+ and Pb 2+, from aqueous solutions. Chemically modified orange peel (MOP) showed a significantly higher metal uptake capacity compared to original orange peel (OP). Fourier Transform Infrared (FTIR) Spectra of peel showed that the carboxylic group peak shifted from 1637 to 1644 cm -1 after Pb (II) ions binding, indicated the involvement of carboxyl groups in Pb(II) ions binding. The metals uptake by MOP was rapid and the equilibrium time was 30 min at constant temperature and pH. Sorption kinetics followed a second-order model. The mechanism of metal sorption by MOP gave good fits for Freundlich and Langmuir models. Desorption of metals and regeneration of the biosorbent was attained simultaneously by acid elution. Even after four cycles of adsorption-elution, the adsorption capacity was regained completely and adsorption efficiency of metal was maintained at around 90%.

  20. Study on an effective industrial waste-based adsorbent for the adsorptive removal of phosphorus from wastewater: equilibrium and kinetics studies.

    PubMed

    Xie, Ruzhen; Chen, Yao; Cheng, Ting; Lai, Yuguo; Jiang, Wenju; Yang, Zhishan

    2016-01-01

    In this work, an effective adsorbent for removing phosphate from aqueous solution was developed from modifying industrial waste--lithium silica fume (LSF). The characterization of LSF before and after modification was investigated using an N2 adsorption-desorption technique (Brunauer-Emmett-Teller, BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Studies were conducted to investigate the effect of adsorbent dose, initial solution pH, contact time, phosphate concentration, and temperature on phosphate removal using this novel adsorbent. The specific surface area for modified LSF (LLSF) is 24.4024 m(2)/g, improved 69.8% compared with unmodified LSF. XRD result suggests that the lanthanum phosphate complex was formed on the surface of LLSF. The maximum phosphate adsorption capacity was 24.096 mg P/g for LLSF, and phosphate removal was favored in the pH range of 3-8. The kinetic data fitted pseudo-second-order kinetic equation, intra-particle diffusion was not the only rate controlling step. The adsorption isotherm results illustrated that the Langmuir model provided the best fit for the equilibrium data. The change in free energy (△G(0)), enthalpy (△H(0)) and entropy (△S(0)) revealed that the adsorption of phosphate on LLSF was spontaneous and endothermic. It was concluded that by modifying with lanthanum, LSF can be turned to be a highly efficient adsorbent in phosphate removal. PMID:27120644

  1. Enhancing adsorption capacity of toxic malachite green dye through chemically modified breadnut peel: equilibrium, thermodynamics, kinetics and regeneration studies.

    PubMed

    Chieng, Hei Ing; Lim, Linda B L; Priyantha, Namal

    2015-01-01

    Breadnut skin, in both its unmodified (KS) and base-modified (BM-KS) forms, was investigated for its potential use as a low-cost adsorbent for the removal of toxic dye, malachite green (MG). Characterization of the adsorbents was carried out using scanning electron microscope, X-ray fluorescence and Fourier transform infra-red spectroscopy. Batch adsorption experiments, carried out under optimized conditions, for the adsorption of MG were fitted using five isotherm models (Langmuir, Freundlich, Dubinin-Radushkevich, Temkin and Sips) and six error functions to determine the best-fit model. The adsorption capacity was greatly enhanced when breadnut skin was chemically modified with NaOH, leading to an adsorption capacity of 353.0 mg g(-1), that was far superior to most reported adsorbents for the removal of MG. Thermodynamics studies indicated that the adsorption of MG was spontaneous on KS and BM-KS, and the reactions were endothermic and exothermic, respectively. Kinetics studies showed that both followed the pseudo-second order. Regeneration experiments on BM-KS indicated that its adsorption capacity was still maintained at>90% even after five cycles. It can be concluded that NaOH-modified breadfruit skin has great potential to be utilized in real-life application as a low-cost adsorbent for the removal of MG in wastewater treatment. PMID:25409587

  2. Calculation of the acid-base equilibrium constants at the alumina/electrolyte interface from the ph dependence of the adsorption of singly charged ions (Na+, Cl-)

    NASA Astrophysics Data System (ADS)

    Gololobova, E. G.; Gorichev, I. G.; Lainer, Yu. A.; Skvortsova, I. V.

    2011-05-01

    A procedure was proposed for the calculation of the acid-base equilibrium constants at an alumina/electrolyte interface from experimental data on the adsorption of singly charged ions (Na+, Cl-) at various pH values. The calculated constants (p K {1/0}= 4.1, p K {2/0}= 11.9, p K {3/0}= 8.3, and p K {4/0}= 7.7) are shown to agree with the values obtained from an experimental pH dependence of the electrokinetic potential and the results of potentiometric titration of Al2O3 suspensions.

  3. pH-responsive diblock copolymer micelles at the silica/aqueous solution interface: Adsorption kinetics and equilibrium studies.

    PubMed

    Sakai, Kenichi; Smith, Emelyn G; Webber, Grant B; Schatz, Christophe; Wanless, Erica J; Bütün, Vural; Armes, Steven P; Biggs, Simon

    2006-08-01

    The adsorption behavior of two examples of a weakly basic diblock copolymer, poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (PDMA-PDEA), at the silica/aqueous solution interface has been investigated using a quartz crystal microbalance with dissipation monitoring and an optical reflectometer. Dynamic and static light scattering measurements have also been carried out to assess aqueous solution properties of such pH-responsive copolymers. In alkaline solution, core-shell micelles are formed above the critical micelle concentration (cmc) by both copolymers, whereas the chains are molecularly dissolved (as unimers) at all concentrations in acidic solution. As a result, the adsorption behavior of PDMA-PDEA diblock copolymers on silica is strongly dependent on both the copolymer concentration and the solution pH. Below the cmc at pH 9, the cationic PDMA-PDEA copolymers adsorb as unimers and the conformation of the adsorbed polymer is essentially flat. At concentrations just above the cmc, the initial adsorption of copolymer onto the silica is dominated by the unimers due to their faster diffusion compared to the much larger micelles. Rearrangement of the adsorbed unimers and/or their subsequent displacement by micelles from solution is then observed during an equilibration period, and the final adsorbed mass is greater than that observed below the cmc. At concentrations well above the cmc, the much higher proportion of micelles in solution facilitates more effective competition for the surface at all stages of the adsorption process and no replacement of initially adsorbed unimers by micelles is evident. However, the adsorbed layer undergoes gradual rearrangement after initial adsorption. This relaxation is believed to result from a combination of further copolymer adsorption and swelling of the adsorbed layer. PMID:16869582

  4. Phosphate Adsorption using Modified Iron Oxide-based Sorbents in Lake Water: Kinetics, Equilibrium, and Column Tests

    EPA Science Inventory

    Adsorption behavior of Bayoxide ® E33 (E33) and three E33-modified sorbents for the removal of phosphate from lake water was investigated in this study. E33-modified sorbents were synthesized by coating with manganese (E33/Mn) and silver (E33/AgI and E33/AgII) nanoparticles. Adso...

  5. 2,4-D adsorption to biochars: effect of preparation conditions on equilibrium adsorption capacity and comparison with commercial activated carbon literature data.

    PubMed

    Kearns, J P; Wellborn, L S; Summers, R S; Knappe, D R U

    2014-10-01

    Batch isotherm experiments were conducted with chars to study adsorption of the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D). Chars generated from corncobs, bamboo and wood chips in a laboratory pyrolyzer at 400-700 °C were compared with traditional kiln charcoals collected from villages in S/SE Asia and with activated carbons (ACs). 2,4-D uptake by laboratory chars obtained from bamboo and wood chips after 14 h of pyrolysis at 700 °C, from wood chips after 96 h of pyrolysis at 600 °C, and one of the field-collected chars (basudha) was comparable to ACs. H:C and O:C ratios declined with pyrolysis temperature and duration while surface area increased to >500 m(2)/g. Increasing pyrolysis intensity by increasing temperature and/or duration of heating was found to positively influence adsorption capacity yield (mg(2,4-D/g(feedstock))) over the range of conditions studied. Economic analysis showed that high temperature chars can be a cost-effective alternative to ACs for water treatment applications. PMID:24934321

  6. Adsorption studies of methylene blue dye on tunisian activated lignin

    NASA Astrophysics Data System (ADS)

    Kriaa, A.; Hamdi, N.; Srasra, E.

    2011-02-01

    Activated carbon prepared from natural lignin, providing from a geological deposit, was used as the adsorbent for the removal of methylene blue (MB) dye from aqueous solutions. Batch adsorption studies were conducted to evaluate various experimental parameters like pH and contact time for the removal of this dye. Effective pH for MB removal was 11. Kinetic study showed that the adsorption of dye was gradual process. Quasi equilibrium reached in 4 h. Pseudo-first-order, pseudo-second-order were used to fit the experimental data. Pseudo-second-order rate equation was able to provide realistic description of adsorption kinetics. The experimental isotherms data were also modelled by the Langmuir and Freundlich equation of adsorption. Equilibrium data fitted well with the Langmuir model with maximum monolayer adsorption capacity of 147 mg/g. Activated lignin was shown to be a promising material for adsorption of MB from aqueous solutions.

  7. RESORCINOL-FORMALDEHYDE ADSORPTION OF CESIUM (Cs+) FROM HANFORD WASTE SOLUTIONS-PART I: BATCH EQUILIBRIUM STUDY

    SciTech Connect

    HASSAN, NEGUIBM

    2004-03-30

    Batch equilibrium measurements were conducted with a granular Resorcinol-Formaldehyde (RF) resin to determine the distribution coefficients (Kds) for cesium. In the tests, Hanford Site actual waste sample containing radioactive cesium and a pretreated waste sample that was spiked with non-radioactive cesium were used. Initial concentrations of non-radioactive cesium in the waste sample were varied to generate an equilibrium isotherm for cesium. Two additional tests were conducted using a liquid to solid phase ratio of 10 and a contact time of 120 hours. The measured distribution coefficient (Kd) for radioactive cesium (137Cs) was 948 mL/g; the Kd for non-radioactive cesium (133Cs) was 1039 mL/g. The Kd for non-radioactive cesium decreased from 1039 to 691 mL/g as the initial cesium concentration increased. Very little change of the Kd was observed at initial cesium concentrations above 64 mg/mL. The maximum sorption capacity for cesium on granular RF resin was 1.17 mmole/g dry resin. T his value was calculated from the fit of the equilibrium isotherm data to the Dubinin-Radushkevich equation. Previously, a total capacity of 2.84 mmole/g was calculated by Bibler and Wallace for air-dried RF resin.

  8. Adsorption of lipase on polypropylene powder.

    PubMed

    Gitlesen, T; Bauer, M; Adlercreutz, P

    1997-04-01

    Adsorption of different lipases by EP-100 polypropylene powder from crude and pure lipase preparations was studied. Langmuir isotherms described the adsorption equilibria well both for protein and lipase activity adsorption. Adsorption isotherms for five different proteins all gave a similar saturation level of 220 mg protein per g carrier. Twelve commercial lipase preparations were tested for selectivity in the adsorption of lipase. For all preparations the selectivity factor was larger than one. In a crude lipase preparation from Pseudomonas fluorescence, the specific activity in solution decreased by two orders of magnitude after adsorption. The adsorption was not significantly influenced by pH changes in the adsorption buffer, indicating that hydrophobic and not electrostatic interactions are the dominating adsorption forces. Adsorption of a crude lipase from Candida rugosa (Sigma) was fast and equilibrium was reached in 30 and 100 min for protein and lipase activity adsorption respectively. Desorption in aqueous solution was negligible. Investigations with seven different lipases showed no correlation between the specific lipolytic activity of dissolved enzyme in aqueous solution and the specific activity of adsorbed enzyme in an esterification reaction in organic solvent. PMID:9106498

  9. Adsorption of 1,1,1,2-tetrafluoroethane by various adsorbents

    SciTech Connect

    Lin, S.H.; Lin, R.C.

    1999-11-01

    Experiments have been conducted to investigate gas-phase adsorption characteristics of 1,1,1,2-tetrafluoroethane (HFC-134a) by activated carbon fiber, extruded activated carbon, granular activated carbon, activated alumina, and molecular sieve. HGC-134a is currently regarded as an excellent replacement for chlorofluorocarbon-12, a refrigerating and cooling agent extensively used previously in all automobiles and many cooling systems. Performances of HFC-134a adsorption were characterized by the equilibrium adsorption capacity, time to reach equilibrium, and desorption efficiency of exhausted adsorbent. A simple thermal treatment process with proper operating temperature and treatment duration was found to be effective for the regeneration of exhausted absorbents. Adsorption isotherms of the empirical Freundlich and Hossens types were observed to adequately represent the equilibrium adsorption data. A mass transfer model based on the pseudo steady state squared driving force was adopted to describe the mass transfer process of HFC-134a adsorption.

  10. Investigation of equilibrium and kinetics of Cr(VI) adsorption by dried Bacillus cereus using response surface methodology.

    PubMed

    Yang, Kai; Zhang, Jing; Yang, Tao; Wang, Hongyu

    2016-01-01

    In this study, response surface methodology (RSM) based on three-variable-five-level central composite rotatable design was used to analyze the effects of combined and individual operating parameters (biomass dose, initial concentration of Cr(VI) and pH) on the Cr(VI) adsorption capacity of dried Bacillus cereus. A quadratic polynomial equation was obtained to predict the adsorbed Cr(VI) amount. Analysis of variance showed that the effect of biomass dose was the key factor in the removal of Cr(VI). The maximum adsorbed Cr(VI) amount (30.93 mg g(-1)) was found at 165.30 mg L(-1), 2.96, and 3.01 g L(-1) for initial Cr(VI) concentration, pH, and biosorbent dosage, respectively. The surface chemical functional groups and microstructure of unloaded and Cr(VI)-loaded dried Bacillus cereus were identified by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM), respectively. Besides, the results gained from these studies indicated that Langmuir isotherm and the second-order rate expression were suitable for the removal of Cr(VI) from wastewater. The results revealed RSM was an effective method for optimizing biosorption process, and dried Bacillus cereus had a remarkable performance on the removal of Cr(VI) from wastewater. PMID:26877045

  11. Process development for removal and recovery of cadmium from wastewater by a low-cost adsorbent: Adsorption rates and equilibrium studies

    SciTech Connect

    Periasamy, K.; Namasivayam, C. . Dept. of Environmental Sciences)

    1994-02-01

    Activated carbon prepared from peanut hulls (PHC), an agricultural waste by-product, has been used for the adsorption of Cd(II) from synthetic wastewater. The adsorption data fit better with the Freundlich adsorption isotherm. The applicability of the Lagergren kinetic model has also been investigated. An almost quantitative removal of 20 mg/L Cd(II) by 0.7 g of PHC/L of aqueous solution was observed in the pH range 3.5--9.5. A comparative study with a commercial granular activated carbon (CAC) showed that the adsorption capacity (K[sub f]) of PHC was 31 times larger than that of CAC.

  12. [Adsorption characteristics of the antibiotic sulfanilamide onto rice husk ash].

    PubMed

    Ji, Ying-Xue; Wang, Feng-He; Zhang, Fan; Zhang, Yan-Hong; Wang, Guo-Xiang; Gu, Zhong-Zhu

    2013-10-01

    Under different conditions of initial rice husk ash (RHA) dosage, oscillating temperature, oscillating frequency and solution pH, the adsorption characteristics of sulfanilamide on RHA with the change of time and its adsorption kinetics were investigated. RHA was characterized by SEM and FTIR before and after sulfanilamide adsorption. The results indicated that the adsorption characteristics of sulfanilamide on RHA was influenced by RHA dosage, oscillating temperature, oscillating frequency and solution pH. Within the RHA dosing range (0. 1-2.0 g.L-1) in this experiment, the optimal temperature for the adsorption was 25C , and with the increase of RHA dosage, the removal efficiency of sulfanilamide increased, the time required to reach adsorption equilibrium was shortened and the adsorptive quantity of sulfanilamide by per unit mass of RHA decreased. A high oscillating frequency was used to ensure the adsorption effect when the RHA concentration was high. Strong acidic and strong alkaline conditions were conducive to the adsorption of sulfanilamide. The analysis of adsorption dynamics showed that for the adsorption process with high RHA dosage ( >or= 1.0 g.L-1), the pseudo-second-order model fitted the adsorption behavior well, and the process was controlled by physical and chemical adsorption. Intraparticle diffusion model showed that the adsorption process was controlled by both membrane diffusion and internal diffusion, and the influence of the former became more obvious with the increase of the adsorbent concentration. Both the SEM and FTIR spectra proved the effective adsorption of sulfanilamide by RHA. PMID:24364310

  13. Use of a physiologically based pharmacokinetic model to study the time to reach brain equilibrium: an experimental analysis of the role of blood-brain barrier permeability, plasma protein binding, and brain tissue binding.

    PubMed

    Liu, Xingrong; Smith, Bill J; Chen, Cuiping; Callegari, Ernesto; Becker, Stacey L; Chen, Xi; Cianfrogna, Julie; Doran, Angela C; Doran, Shawn D; Gibbs, John P; Hosea, Natilie; Liu, Jianhua; Nelson, Frederick R; Szewc, Mark A; Van Deusen, Jeffery

    2005-06-01

    This study was designed 1) to examine the effects of blood-brain barrier (BBB) permeability [quantified as permeability-surface area product (PS)], unbound fraction in plasma (f(u,plasma)), and brain tissue (f(u,brain)) on the time to reach equilibrium between brain and plasma and 2) to investigate the drug discovery strategies to design and select compounds that can rapidly penetrate the BBB and distribute to the site of action. The pharmacokinetics of seven model compounds: caffeine, CP-141938 [methoxy-3-[(2-phenyl-piperadinyl-3-amino)-methyl]-phenyl-N-methyl-methane-sulfonamide], fluoxetine, NFPS [N[3-(4'-fluorophenyl)-3-(4'-phenylphenoxy)propyl]sarcosine], propranolol, theobromine, and theophylline in rat brain and plasma after subcutaneous administration were studied. The in vivo log PS and log f(u,brain) calculated using a physiologically based pharmacokinetic model correlates with in situ log PS (R(2) = 0.83) and in vitro log f(u,brain) (R(2) = 0.69), where the in situ PS and in vitro f(u,brain) was determined using in situ brain perfusion and equilibrium dialysis using brain homogenate, respectively. The time to achieve brain equilibrium can be quantitated with a proposed parameter, intrinsic brain equilibrium half-life [t(1/2eq,in) = V(b)ln2/(PS . f(u,brain))], where V(b) is the physiological volume of brain. The in vivo log t(1/2eq,in) does not correlate with in situ log PS (R(2) < 0.01) but correlates inversely with log(PS . f(u,brain)) (R(2) = 0.85). The present study demonstrates that rapid brain equilibration requires a combination of high BBB permeability and low brain tissue binding. A high BBB permeability alone cannot guarantee a rapid equilibration. The strategy to select compounds with rapid brain equilibration in drug discovery should identify compounds with high BBB permeability and low nonspecific binding in brain tissue. PMID:15743928

  14. [Adsorption of perfluorooctanesulfonate (PFOS) onto modified activated carbons].

    PubMed

    Tong, Xi-Zhen; Shi, Bao-You; Xie, Yue; Wang, Dong-Sheng

    2012-09-01

    Modified coal and coconut shell based powdered activated carbons (PACs) were prepared by FeCl3 and medium power microwave treatment, respectively. Batch experiments were carried out to evaluate the characteristics of adsorption equilibrium and kinetics of perfluorooctanesulfonate (PFOS) onto original and modified PACs. Based on pore structure and surface functional groups characterization, the adsorption behaviors of modified and original PACs were compared. The competitive adsorption of humic acid (HA) and PFOS on original and modified coconut shell PACs were also investigated. Results showed that both Fe3+ and medium power microwave treatments changed the pore structure and surface functional groups of coal and coconut shell PACs, but the changing effects were different. The adsorption of PFOS on two modified coconut shell-based PACs was significantly improved. While the adsorption of modified coal-based activated carbons declined. The adsorption kinetics of PFOS onto original and modified coconut shell-based activated carbons were the same, and the time of reaching adsorption equilibrium was about 6 hours. In the presence of HA, the adsorption of PFOS by modified PAC was reduced but still higher than that of the original. PMID:23243870

  15. Adsorption of toxic metal ion Cr(VI) from aqueous state by TiO2-MCM-41: equilibrium and kinetic studies.

    PubMed

    Parida, Kulamani; Mishra, Krushna Gopal; Dash, Suresh Kumar

    2012-11-30

    This paper deals with the immobilization of various weight percentage of TiO(2) on mesoporous MCM-41, characterization of the materials by X-ray diffraction (XRD), nitrogen adsorption-desorption, Fourier Transform Infrared (FTIR) analysis, UV-vis diffuse reflectance spectroscopy (DRS) and evaluation of the adsorption capacity toward Cr(VI) removal. It is found that the MCM-41 structure retained after loading of TiO(2) but the surface area and pore diameter decreased due to pore blockage. Adsorption of Cr(VI) from aqueous state was investigated on TiO(2)-MCM-41 by changing various parameters such as pH, metal ion concentration, and the temperature. When TiO(2) loading was more than 20 wt.%, the adsorption activity (25)TiO(2)-MCM-41 reduced significantly due to considerable decrease in the surface area. It is also observed that TiO(2) and neat MCM-41 exhibits very less Cr(VI) adsorption compared to TiO(2)-MCM-41. The adsorption of Cr(VI) onto (20)TiO(2)-MCM-41 at pH~5.5 and temperature 323 K was 91% at 100mg/L Cr(VI) metal ion concentration in 80 min. The experimental data fitted well to Langmuir and Freundlich isotherms. The adsorption of Cr(VI) on TiO(2)-MCM-41 followed a second order kinetics with higher values of intra-particle diffusion rate. Thermodynamic parameters suggested that the adsorption process is endothermic in nature and desorption studies indicated a chemisorption mode. PMID:23092612

  16. Removal of aqueous uranyl ions by magnetic functionalized carboxymethylcellulose and adsorption property investigation

    NASA Astrophysics Data System (ADS)

    Gao, Yangyang; Yuan, Yali; Ma, Dandan; Li, Le; Li, Yuhui; Xu, Wenhui; Tao, Wei

    2014-10-01

    Magnetic carboxymethylcellulose (CMC/Fe3O4) was used as a framework adsorption material to remove uranium ions from aqueous solutions. Carboxyl functional groups were grafted onto the CMC/Fe3O4. The maximum adsorption capacity of the magnetic composite toward U(VI) was 122.48 mg/g. Kinetic and thermodynamic parameters of the adsorption process were estimated. The pseudo-second-order model was more suitable and it proved to be an endothermic and spontaneous process. The Langmuir and Freundlich models were applied to evaluate the adsorption isotherm. The data matched well with Langmuir model after equilibrium was reached and with Freundlich model before equilibrium was reached.

  17. Equilibrium adsorption isotherm studies of Cu (II) and Co (II) in high concentration aqueous solutions on Ag-TiO2-modified kaolinite ceramic adsorbents

    NASA Astrophysics Data System (ADS)

    Ajenifuja, E.; Ajao, J. A.; Ajayi, E. O. B.

    2016-03-01

    Photocatalytic ceramic adsorbents were prepared from locally sourced kaolinite clay minerals for the removal of copper and cobalt ions from high concentration aqueous solutions. The minerals were treated with mild acid before modification using silver nanoparticles sources and titanium-oxide nanoparticles. Batch adsorption experiment was carried out on the targeted ions and the results were analyzed by Langmuir and Freundlich equation at different concentrations (100-1000 mg/l). As-received raw materials do not exhibit any adsorption capacity. However, the adsorption isotherms for modified kaolinite clay ceramic adsorbents could be fitted well by the Langmuir model for Cu2+ and Co2+ with correlation coefficient (R) of up to 0.99705. The highest and lowest monolayer coverage (q max) were 93.023 and 30.497 mg/g for Cu2+ and Co2+, respectively. The separation factor (R L ) was less than one (<1), indicating that the adsorption of metal ions on modified ceramic adsorbent is favorable. The highest adsorbent adsorption capacity (K f ) and intensity (n) constants obtained from Freundlich model are 14.401 (Cu2+ on KLN-T) and 6.057 (Co2+ on KLN-T).

  18. Adsorption of C.I. Reactive Red 228 and Congo Red dye from aqueous solution by amino-functionalized Fe3O4 particles: kinetics, equilibrium, and thermodynamics.

    PubMed

    Yan, Ting-guo; Wang, Li-Juan

    2014-01-01

    A magnetic adsorbent was synthesized by γ-aminopropyltriethoxysilane (APTES) modification of Fe(3)O(4) particles using a two-step process. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and vibration sample magnetometry were used to characterize the obtained magnetic adsorbent. EDS and XPS showed that APTES polymer was successfully introduced onto the as-prepared Fe(3)O(4)/APTES particle surfaces. The saturation magnetization of the magnetic adsorbent was around 65 emu g(-1), which indicated that the dye can be removed fast and efficiently from aqueous solution with an external magnetic field. The maximum adsorption capacities of Fe(3)O(4)/APTES for C.I. Reactive Red 228 (RR 228) and Congo Red (CR) were 51.4 and 118.8 mg g(-1), respectively. The adsorption of C.I. Reactive Red 228 (RR 228) and Congo Red (CR) on Fe(3)O(4)/APTES particles corresponded well to the Langmuir model and the Freundlich model, respectively. The adsorption processes for RR 228 and CR followed the pseudo-second-order model. The Boyd's film-diffusion model showed that film diffusion also played a major role in the studied adsorption processes for both dyes. Thermodynamic study indicated that both of the adsorption processes of the two dyes are spontaneous exothermic. PMID:24552735

  19. Neon and CO2 adsorption on open carbon nanohorns.

    PubMed

    Krungleviciute, Vaiva; Ziegler, Carl A; Banjara, Shree R; Yudasaka, Masako; Iijima, S; Migone, Aldo D

    2013-07-30

    We present the results of a thermodynamics and kinetics study of the adsorption of neon and carbon dioxide on aggregates of chemically opened carbon nanohorns. Both the equilibrium adsorption characteristics, as well as the dependence of the kinetic behavior on sorbent loading, are different for these two adsorbates. For neon the adsorption isotherms display two steps before reaching the saturated vapor pressure, corresponding to adsorption on strong and on weak binding sites; the isosteric heat of adsorption is a decreasing function of sorbent loading (this quantity varies by about a factor of 2 on the range of loadings studied), and the speed of the adsorption kinetics increases with increasing loading. By contrast, for carbon dioxide there are no substeps in the adsorption isotherms; the isosteric heat is a nonmonotonic function of loading, the value of the isosteric heat never differs from the bulk heat of sublimation by more than 15%, and the kinetic behavior is opposite to that of neon, with equilibration times increasing for higher sorbent loadings. We explain the difference in the equilibrium properties observed for neon and carbon dioxide in terms of differences in the relative strengths of adsorbate-adsorbate to adsorbate-sorbent interaction for these species. PMID:23802764

  20. Removal of mercury(II) ions in aqueous solution using the peel biomass of Pachira aquatica Aubl: kinetics and adsorption equilibrium studies.

    PubMed

    Santana, Andrea J; Dos Santos, Walter N L; Silva, Laiana O B; das Virgens, Cesário F

    2016-05-01

    Mercury is a highly toxic substance that is a health hazard to humans. This study aims to investigate powders obtained from the peel of the fruit of Pachira aquatica Aubl, in its in natura and/or acidified form, as an adsorbent for the removal of mercury ions in aqueous solution. The materials were characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis. The infrared spectra showed bands corresponding to the axial deformation of carbonyls from carboxylic acids, the most important functional group responsible for fixing the metal species to the adsorbent material. The thermograms displayed mass losses related to the decomposition of three major components, i.e., hemicellulose, cellulose, and lignin. The adsorption process was evaluated using cold-vapor atomic fluorescence spectrometry (CV AFS) and cold-vapor atomic absorption spectrometry (CV AAS). Three isotherm models were employed. The adsorption isotherm model, Langmuir-Freundlich, best represented the adsorption process, and the maximum adsorption capacity was predicted to be 0.71 and 0.58 mg g(-1) at 25 °C in nature and acidified, respectively. Adsorption efficiencies were further tested on real aqueous wastewater samples, and removal of Hg(II) was recorded as 69.6 % for biomass acidified and 76.3 % for biomass in nature. Results obtained from sorption experiments on real aqueous wastewater samples revealed that recovery of the target metal ions was very satisfactory. The pseudo-second-order model showed the best correlation to the experimental data. The current findings showed that the investigated materials are potential adsorbents for mercury(II) ion removal in aqueous solution, with acidified P. aquatica Aubl being the most efficient adsorbent. PMID:27084802

  1. Individual and competitive adsorption of phenol and nickel onto multiwalled carbon nanotubes

    PubMed Central

    Abdel-Ghani, Nour T.; El-Chaghaby, Ghadir A.; Helal, Farag S.

    2014-01-01

    Individual and competitive adsorption studies were carried out to investigate the removal of phenol and nickel ions by adsorption onto multiwalled carbon nanotubes (MWCNTs). The carbon nanotubes were characterized by different techniques such as X-ray diffraction, scanning electron microscopy, thermal analysis and Fourier transformation infrared spectroscopy. The different experimental conditions affecting the adsorption process were investigated. Kinetics and equilibrium models were tested for fitting the adsorption experimental data. The characterization experimental results proved that the studied adsorbent possess different surface functional groups as well as typical morphological features. The batch experiments revealed that 300 min of contact time was enough to achieve equilibrium for the adsorption of both phenol and nickel at an initial adsorbate concentration of 25 mg/l, an adsorbent dosage of 5 g/l, and a solution pH of 7. The adsorption of phenol and nickel by MWCNTs followed the pseudo-second order kinetic model and the intraparticle diffusion model was quite good in describing the adsorption mechanism. The Langmuir equilibrium model fitted well the experimental data indicating the homogeneity of the adsorbent surface sites. The maximum Langmuir adsorption capacities were found to be 32.23 and 6.09 mg/g, for phenol and Ni ions, respectively. The removal efficiency of MWCNTs for nickel ions or phenol in real wastewater samples at the optimum conditions reached up to 60% and 70%, respectively. PMID:26257938

  2. Study the adsorption of phenol from aqueous solution on hydroxyapatite nanopowders.

    PubMed

    Lin, Kaili; Pan, Jiayong; Chen, Yiwei; Cheng, Rongming; Xu, Xuecheng

    2009-01-15

    In this study, the hydroxyapatite (HAp) nanopowders prepared by chemical precipitation method were used as the adsorbent, and the potential of HAp nanopowders for phenol adsorption from aqueous solution was studied. The effect of contact time, initial phenol concentration, pH, adsorbent dosage, solution temperature and adsorbent calcining temperature on the phenol adsorption, and the adsorption kinetic, equilibrium and thermodynamic parameters were investigated. The results showed that the HAp nanopowders possessed good adsorption ability to phenol. The adsorption process was fast, and it reached equilibrium in 2h of contact. The initial phenol concentration, pH and the adsorbent calcining temperature played obvious effects on the phenol adsorption capacity onto HAp nanopowders. Increase in the initial phenol concentration could effectively increase the phenol adsorption capacity. At the same time, increase in the pH to high-acidity or to high-alkalinity also resulted in the increase in the phenol adsorption capacity. Increase in the HAp dosage could effectively increase the phenol adsorption percent. However, the higher calcining temperature of HAp nanopowders could obviously decrease the adsorption capacity. The maximum phenol adsorption capacity was obtained as 10.33mg/g for 400mg/L initial phenol concentrations at pH 6.4 and 60 degrees C. The adsorption kinetic and the isotherm studies showed that the pseudo-second-order model and the Freundlich isotherm were the best choices to describe the adsorption behaviors. The thermodynamic parameters suggested that the adsorption of phenol onto HAp was physisorption, spontaneous and endothermic in nature. PMID:18573599

  3. Comparison of adsorption equilibrium models for the study of CL-, NO3- and SO4(2-) removal from aqueous solutions by an anion exchange resin.

    PubMed

    Dron, Julien; Dodi, Alain

    2011-06-15

    The removal of chloride, nitrate and sulfate ions from aqueous solutions by a macroporous resin is studied through the ion exchange systems OH(-)/Cl(-), OH(-)/NO(3)(-), OH(-)/SO(4)(2-), and HCO(3)(-)/Cl(-), Cl(-)/NO(3)(-), Cl(-)/SO(4)(2-). They are investigated by means of Langmuir, Freundlich, Dubinin-Radushkevitch (D-R) and Dubinin-Astakhov (D-A) single-component adsorption isotherms. The sorption parameters and the fitting of the models are determined by nonlinear regression and discussed. The Langmuir model provides a fair estimation of the sorption capacity whatever the system under study, on the contrary to Freundlich and D-R models. The adsorption energies deduced from Dubinin and Langmuir isotherms are in good agreement, and the surface parameter of the D-A isotherm appears consistent. All models agree on the order of affinity OH(-)adsorption isotherms. The nonlinear regression results are also compared with linear regressions. While the parameter values are not affected, the evaluation of the best fitting model is biased by linearization. PMID:21497015

  4. Mechanism of amitriptyline adsorption on Ca-montmorillonite (SAz-2).

    PubMed

    Chang, Po-Hsiang; Jiang, Wei-Teh; Li, Zhaohui; Kuo, Chung-Yih; Jean, Jiin-Shuh; Chen, Wan-Ru; Lv, Guocheng

    2014-07-30

    The uptake of amitriptyline (AMI) from aqueous environment by Ca-montmorillonite (SAz-2) was studied in a batch system under different physicochemical conditions. The adsorbent was characterized by X-ray diffraction and Fourier transform infrared (FTIR) analyses. The AMI adsorption on SAz-2 obeyed the Langmuir isotherm with a capacity of 330mg/g (1.05mmol/g) at pH 6-7. The adsorption kinetics was fast, almost reaching equilibrium in 2h, and followed a pseudo-second-order kinetic model. Desorption of exchangeable cations correlated with the AMI adsorption well, indicating that cation exchange was the major mechanism. X-ray diffraction patterns showing significant expansions of the d001 spacing and characteristic FTIR band shifts toward higher frequencies after AMI adsorption onto SAz-2 indicated that the adsorbed AMI molecules were intercalated into the interlayers of the mineral. Thermodynamic parameters based on partitioning coefficients suggested that the AMI adsorption was an endothermic physisorption at high adsorption levels. At low and higher AMI adsorption levels, the intercalated AMI molecules take a horizontal monolayer and bilayer conformation, respectively. The higher adsorption capacity suggested that SAz-2 could be a good candidate to remove AMI from wastewater and would be an important environmental sink for the fate and transport of AMI in soils and groundwater. PMID:24373983

  5. Adsorption of clofibric acid and ketoprofen onto powdered activated carbon: effect of natural organic matter.

    PubMed

    Gao, Yaohuan; Deshusses, Marc A

    2011-12-01

    The adsorption of two acidic pharmaceutically active compounds (PhACs), clofibric acid and ketoprofen, onto powdered activated carbon (PAC) was investigated with a particular focus on the influence of natural organic matter (NOM) on the adsorption of the PhACs. Suwannee River humic acids (SRHAs) were used as a substitute for NOM. Batch adsorption experiments were conducted to obtain adsorption kinetics and adsorption isotherms with and without SRHAs in the system. The adsorption isotherms and adsorption kinetics showed that the adsorption ofclofibric acid was not significantly affected by the presence of SRHAs at a concentration of 5 mg (as carbon) L(-1). An adsorption capacity of 70 to 140 mg g(-1) was observed and equilibrium was reached within 48 h. In contrast, the adsorption of ketoprofen was markedly decreased (from about 120 mg g(-1) to 70-100 mg g(-1)) in the presence of SRHAs. Higher initial concentrations of clofibric acid than ketoprofen during testing may explain the different behaviours that were observed. Also, the more hydrophobic ketoprofen molecules may have less affinity for PAC when humic acids (which are hydrophilic) are present. The possible intermolecular forces that could account for the different behaviour of clofibric acid and ketoprofen adsorption onto PAC are discussed. In particular, the relevance of electrostatic forces, electron donor-acceptor interaction, hydrogen bonding and London dispersion forces are discussed PMID:22439557

  6. Preparation of titanium peroxide and its selective adsorption property on cationic dyes

    NASA Astrophysics Data System (ADS)

    Zhao, Xiao-guang; Huang, Ji-guo; Wang, Bo; Bi, Qiang; Dong, Li-li; Liu, Xing-juan

    2014-02-01

    Titanium peroxide powder was prepared with the reaction of titanium sulfate and H2O2 and showed good selective adsorption property on cationic dyes. The obtained material was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and thermogravimetric and differential scanning calorimetry (TG-DSC). The selective adsorption property was confirmed and evaluated by adsorption experiments of methyl orange (MO), phenol and three kinds of cationic dyes including methylene blue (MB), malachite green (MG) and neutral red (NR). The adsorption was very fast and adsorption equilibrium was reached in a very short time for all three cationic dyes. The adsorption kinetics of MB, MG and NR were studied then. It was found that the adsorption data fitted perfectly with the pseudo-second-order kinetics and the saturated adsorption capacities for MB, MG and NR were 224.37, 251.38 and 327.61 mg/g at 25 °C, respectively. The characterization and adsorption results indicated the controlling mechanism of adsorption processes could be electrostatic adsorption.

  7. Investigating the thermodynamic stability of Bacillus subtilis spore-uranium(VI) adsorption though surface complexation modeling

    NASA Astrophysics Data System (ADS)

    Harrold, Z.; Hertel, M.; Gorman-Lewis, D.

    2012-12-01

    Dissolved uranium speciation, mobility, and remediation are increasingly important topics given continued and potential uranium (U) release from mining operations and nuclear waste. Vegetative bacterial cell surfaces are known to adsorb uranium and may influence uranium speciation in the environment. Previous investigations regarding U(VI) adsorption to bacterial spores, a differentiated and dormant cell type with a tough proteinaceous coat, include U adsorption affinity and XAFS data. We investigated the thermodynamic stability of aerobic, pH dependent uranium adsorption to bacterial spore surfaces using purified Bacillus subtilis spores in solution with 5ppm uranium. Adsorption reversibility and kinetic experiments indicate that uranium does not precipitate over the duration of the experiments and equilibrium is reached within 20 minutes. Uranium-spore adsorption edges exhibited adsorption at all pH measured between 2 and 10. Maximum adsorption was achieved around pH 7 and decreased as pH increased above 7. We used surface complexation modeling (SCM) to quantify uranium adsorption based on balanced chemical equations and derive thermodynamic stability constants for discrete uranium-spore adsorption reactions. Site specific thermodynamic stability constants provide insight on interactions occurring between aqueous uranium species and spore surface ligands. The uranium adsorption data and SCM parameters described herein, also provide a basis for predicting the influence of bacterial spores on uranium speciation in natural systems and investigating their potential as biosorption agents in engineered systems.

  8. TiO2 hollow microspheres with mesoporous surface: Superior adsorption performance for dye removal

    NASA Astrophysics Data System (ADS)

    Wang, Ran; Cai, Xia; Shen, Fenglei

    2014-06-01

    TiO2 hollow microspheres with mesoporous surface were synthesized by a facile template-assisted solvothermal reaction. The adsorption performance of TiO2 hollow microspheres for removing Methylene Blue from aqueous solution has been investigated. The comparative adsorption study indicated that adsorption capacity of TiO2 hollow microspheres with mesoporous surface is markedly higher than that of solid microsphere. The equilibrium data fitted well with the Langmuir model and the maximum adsorption capacity reached 196.83 mg/g. The kinetics of dye adsorption followed the pseudo-second-order model and the adsorbed dye could be degraded completely by the subsequent photocatalytic process. These TiO2 hollow microspheres can be considered as a low-cost alternative adsorbent for removal of organic pollutants from wastewater.

  9. A novel reusable nanocomposite: FeOOH/CBC and its adsorptive property for methyl orange

    NASA Astrophysics Data System (ADS)

    Wang, Zhuanpei; Ma, Yongjun; He, Honglei; Pei, Chonghua; He, Ping

    2015-03-01

    Porous network-like FeOOH/ carbonized bacterial cellulose (FeOOH/CBC) nanocomposite was successfully prepared and used as adsorbent of organic dyes. The phases, morphology, structure and adsorptive properties of FeOOH/CBC nanocomposite were characterized by XRD, FI-IR, SEM, TEM, BET and UV-vis. The adsorption equilibrium of as-prepared FeOOH/CBC nanocomposite for methyl orange (MO) was achieved within one hour, with the maximum adsorption capacity for MO reaching 107.68 mg/g at pH 6.0 and 30 °C. As-prepared FeOOH/CBC nanocomposite maintains high adsorption activities after four times of adsorption and desorption, accompanying the removal rate for MO is up to 60% in 10 min.

  10. Poliovirus Adsorption by 34 Minerals and Soils

    PubMed Central

    Moore, Rebecca S.; Taylor, Dene H.; Sturman, Lawrence S.; Reddy, Michael M.; Fuhs, G. Wolfgang

    1981-01-01

    The adsorption of radiolabeled infectious poliovirus type 2 by 34 well-defined soils and mineral substrates was analyzed in a synthetic freshwater medium containing 1 mM CaCl2 and 1.25 mM NaHCO3 at pH 7. In a model system, adsorption of poliovirus by Ottawa sand was rapid and reached equilibrium within 1 h at 4°C. Near saturation, the adsorption could be described by the Langmuir equation; the apparent surface saturation was 2.5 × 106 plaque-forming units of poliovirus per mg of Ottawa sand. At low surface coverage, adsorption was described by the Freundlich equation. The soils and minerals used ranged from acidic to basic and from high in organic content to organic free. The available negative surface charge on each substrate was measured by the adsorption of a cationic polyelectrolyte, polydiallyldimethylammonium chloride. Most of the substrates adsorbed more than 95% of the virus. In general, soils, in comparison with minerals, were weak adsorbents. Among the soils, muck and Genesee silt loam were the poorest adsorbents; among the minerals, montmorillonite, glauconite, and bituminous shale were the least effective. The most effective adsorbents were magnetite sand and hematite, which are predominantly oxides of iron. Correlation coefficients for substrate properties and virus adsorption revealed that the elemental composition of the adsorbents had little effect on poliovirus uptake. Substrate surface area and pH, by themselves, were not significantly correlated with poliovirus uptake. A strong negative correlation was found between poliovirus adsorption and both the contents of organic matter and the available negative surface charge on the substrates as determined by their capacities for adsorbing the cationic polyelectrolyte, polydiallyldimethylammonium chloride. PMID:6274259

  11. Comparative study on adsorption of perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) by different adsorbents in water.

    PubMed

    Yao, Yuan; Volchek, Konstantin; Brown, Carl E; Robinson, Adam; Obal, Terry

    2014-01-01

    Perfluorinated compounds (PFCs) are emerging environmental pollutants. Perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are the two primary PFC contaminants that are widely found in water, particularly in groundwater. This study compared the adsorption behaviors of PFOS and PFOA on several commercially available adsorbents in water. The tested adsorbents include granular activated carbon (GAC: Filtrasorb 400), powdered activated carbon, multi-walled carbon nanotube (MCN), double-walled carbon nanotube, anion-exchange resin (AER: IRA67), non-ion-exchange polymer, alumina, and silica. The study demonstrated that adsorption is an effective technique for the removal of PFOS/PFOA from aqueous solutions. The kinetic tests showed that the adsorption onto AER reaches equilibrium rapidly (2 h), while it takes approximately 4 and 24 h to reach equilibrium for MCN and GAC, respectively. In terms of adsorption capacity, AER and GAC were identified as the most effective adsorbents to remove PFOS/PFOA from water. Furthermore, MCN, AER, and GAC proved to have high PFOS/PFOA removal efficiencies (≥98%). AER (IRA67) and GAC (Filtrasorb 400) were thus identified as the most promising adsorbents for treating PFOS/PFOA-contaminated groundwater at mg L(-1) level based on their equilibrium times, adsorption capacities, removal efficiencies, and associated costs. PMID:25521134

  12. In vitro adsorption of aluminum by an edible biopolymer poly(γ-glutamic acid).

    PubMed

    Rajan, Yesudoss Christu; Inbaraj, Baskaran Stephen; Chen, Bing Huei

    2014-05-21

    Accumulation of aluminum in human has been reported to be associated with dementia, Parkinson's disease, and Alzheimer's disease. The objectives of this study were to evaluate an edible biopolymer poly(γ-glutamic acid) (γ-PGA) for aluminum removal efficiency under in vitro conditions as affected by pH, contact time, aluminum concentration, temperature, ionic strength, and essential metals in both aqueous aluminum solution and simulated gastrointestinal fluid (GIF). A low aluminum adsorption occurred at pH 1.5-2.5, followed by a maximum adsorption at pH 3.0-4.0 and precipitating thereafter as aluminum hydroxide at pH > 4. Adsorption was extremely fast with 81-96% of total adsorption being attained within 1 min, reaching equilibrium in 5-10 min. Kinetic data at low (10 mg/L) and high (50 mg/L) concentrations were well described by pseudo-first-order and pseudo-second-order models, respectively. Equilibrium adsorption isotherms at different temperatures were precisely fitted by both Langmuir and Redlich-Peterson models with the maximum adsorption capacities at 25, 37, and 50 °C being 35.85, 38.68, and 44.23 mg/g, respectively. Thermodynamic calculations suggested endothermic and spontaneous nature of aluminum adsorption by γ-PGA with increased randomness at the solid/solution interface. Variation in ionic strengths did not alter the adsorption capacity, however, the incorporation of essential metals significantly reduced the aluminum adsorption by following the order copper > iron > zinc > calcium > potassium. Compared to aqueous solution, the aluminum adsorption from simulated GIF was high at all studied pH (1-4) with Langmuir monolayer adsorption capacity being 49.43 mg/g at 37 °C and pH 4. The outcome of this study suggests that γ-PGA could be used as a safe detoxifying agent for aluminum. PMID:24799126

  13. Equilibrium and kinetic mechanisms of woody biochar on aqueous glyphosate removal.

    PubMed

    Mayakaduwa, S S; Kumarathilaka, Prasanna; Herath, Indika; Ahmad, Mahtab; Al-Wabel, Mohammed; Ok, Yong Sik; Usman, Adel; Abduljabbar, Adel; Vithanage, Meththika

    2016-02-01

    We investigated the removal of aqueous glyphosate using woody (dendro) biochar obtained as a waste by product from bioenergy industry. Equilibrium isotherms and kinetics data were obtained by adsorption experiments. Glyphosate adsorption was strongly pH dependent occurring maximum in the pH range of 5-6. The protonated amino moiety of the glyphosate molecule at this pH may interact with π electron rich biochar surface via π-π electron donor-acceptor interactions. Isotherm data were best fitted to the Freundlich and Temkin models indicating multilayer sorption of glyphosate. The maximum adsorption capacity of dendro biochar for glyphosate was determined by the isotherm modeling to be as 44 mg/g. Adsorption seemed to be quite fast, reaching the equilibrium <1 h. Pseudo-second order model was found to be the most effective in describing kinetics whereas the rate limiting step possibly be chemical adsorption involving valence forces through sharing or exchanging electrons between the adsorbent and sorbate. The FTIR spectral analysis indicated the involvement of functional groups such as phenolic, amine, carboxylic and phosphate in adsorption. Hence, a heterogeneous chemisorption process between adsorbate molecules and functional groups on biochar surface can be suggested as the mechanisms involved in glyphosate removal. PMID:26340852

  14. Effect of pyrolysis temperatures and times on the adsorption of cadmium onto orange peel derived biochar.

    PubMed

    Tran, Hai Nguyen; You, Sheng-Jie; Chao, Huan-Ping

    2016-02-01

    The mechanism and capacity of adsorption of cadmium (Cd) on orange peel (OP)-derived biochar at various pyrolysis temperatures (400, 500, 600, 700 and 800°C) and heating times (2 and 6 h) were investigated. Biochar was characterized using proximate analysis, point of zero charge (PZC) analysis, Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction. Equilibrium and kinetic experiments of Cd adsorption on biochar were performed. The results indicated that the pH value at PZC of biochar approached 9.5. Equilibrium can be reached rapidly (within 1 min) in kinetic experiments and a removal rate of 80.6-96.9% can be generated. The results fitted the pseudo-second-order model closely. The adsorption capacity was estimated using the Langmuir model. The adsorption capacity of Cd on biochar was independent of the pyrolysis temperature and heating time (p>0.01). The maximum adsorption capacity of Cd was 114.69 (mg g(-1)). The adsorption of Cd on biochar was regarded as chemisorption. The primary adsorption mechanisms were regarded as Cπ-cation interactions and surface precipitation. Cadmium can react with calcite to form the precipitation of (Ca,Cd)CO3 on the surface of biochar. The OP-derived biochar can be considered a favourable alternative and a new green adsorbent for removing Cd(2+) ions from an aqueous solution. PMID:26608900

  15. Adsorption of paraquat using methacrylic acid-modified rice husk.

    PubMed

    Hsu, Shih-Tong; Pan, Ting-Chung

    2007-12-01

    This work investigates the adsorption of paraquat from aqueous medium using a methacrylic acid (MAA)-modified rice husk. The carboxyl groups were chemically bound to the surface of the rice husk by graft copolymerization using Fenton's reagent as a redox initiator. The graft copolymerization was examined to determine the H(2)O(2) concentration and the amount of MAA monomer used. FT-IR spectra confirmed the presence of carbonyl groups on the structural units of the rice husk derivative. The MAA-modified rice husks were hydrolyzed to sodium salt and used to adsorb paraquat. The adsorption was rapid in the first few minutes and quickly reached equilibrium. Equilibrium adsorption data are more consistent with the Langmuir isotherm equation than with the Freundlich equation. The maximum adsorption capacity of modified rice husks was 317.7mg/g-adsorbent. This value clearly exceeds the 60mg/g of Fuller's earth and the 90mg/g of activated carbon, which are the most commonly used binding agents for paraquat. PMID:17303413

  16. Liquid-phase adsorption of organic compounds by granular activated carbon and activated carbon fibers

    SciTech Connect

    Lin, S.H.; Hsu, F.M.

    1995-06-01

    Liquid-phase adsorption of organic compounds by granular activated carbon (GAC) and activated carbon fibers (ACFs) is investigated. Acetone, isopropyl alcohol (IPA), phenol, and tetrahydrofuran (THF) were employed as the model compounds for the present study. It is observed from the experimental results that adsorption of organic compounds by GAC and ACF is influenced by the BET (Brunauer-Emmett-Teller) surface area of adsorbent and the molecular weight, polarity, and solubility of the adsorbate. The adsorption characteristics of GAC and ACFs were found to differ rather significantly. In terms of the adsorption capacity of organic compounds, the time to reach equilibrium adsorption, and the time for complete desorption, ACFs have been observed to be considerably better than GAC. For the organic compounds tested here, the GAC adsorptions were shown to be represented well by the Langmuir isotherm while the ACF adsorption could be adequately described by the Langmuir or the Freundlich isotherm. Column adsorption tests indicated that the exhausted ACFs can be effectively regenerated by static in situ thermal desorption at 150 C, but the same regeneration conditions do not do as well for the exhausted GAC.

  17. Adsorption of methylene blue and Congo red from aqueous solution by activated carbon and carbon nanotubes.

    PubMed

    Szlachta, M; Wójtowicz, P

    2013-01-01

    This study was conducted to determine the adsorption removal of dyes by powdered activated carbon (PAC, Norit) and multi-walled carbon nanotubes (MWCNTs, Chinese Academy of Science) from an aqueous solution. Methylene blue (MB) and Congo red (CR) were selected as model compounds. The adsorbents tested have a high surface area (PAC 835 m(2)/g, MWCNTs 358 m(2)/g) and a well-developed porous structure which enabled the effective treatment of dye-contaminated waters and wastewaters. To evaluate the capacity of PAC and MWCNTs to adsorb dyes, a series of batch adsorption experiments was performed. Both adsorbents exhibited a high adsorptive capacity for MB and CR, and equilibrium data fitted well with the Langmuir model, with the maximum adsorption capacity up to 400 mg/g for MB and 500 mg/g for CR. The separation factor, RL, revealed the favorable nature of the adsorption process under experimental conditions. The kinetics of adsorption was studied at various initial dye concentrations and solution temperatures. The pseudo-second-order model was used for determining the adsorption kinetics of MB and CR. The data obtained show that adsorption of both dyes was rapid in the initial stage and followed by slower processing to reach the plateau. The uptake of dyes increased with contact time, irrespective of their initial concentration and solution temperature. However, changes in the solution temperature did not significantly influence dye removal. PMID:24292474

  18. Partition Equilibrium

    NASA Astrophysics Data System (ADS)

    Feldman, Michal; Tennenholtz, Moshe

    We introduce partition equilibrium and study its existence in resource selection games (RSG). In partition equilibrium the agents are partitioned into coalitions, and only deviations by the prescribed coalitions are considered. This is in difference to the classical concept of strong equilibrium according to which any subset of the agents may deviate. In resource selection games, each agent selects a resource from a set of resources, and its payoff is an increasing (or non-decreasing) function of the number of agents selecting its resource. While it has been shown that strong equilibrium exists in resource selection games, these games do not possess super-strong equilibrium, in which a fruitful deviation benefits at least one deviator without hurting any other deviator, even in the case of two identical resources with increasing cost functions. Similarly, strong equilibrium does not exist for that restricted two identical resources setting when the game is played repeatedly. We prove that for any given partition there exists a super-strong equilibrium for resource selection games of identical resources with increasing cost functions; we also show similar existence results for a variety of other classes of resource selection games. For the case of repeated games we identify partitions that guarantee the existence of strong equilibrium. Together, our work introduces a natural concept, which turns out to lead to positive and applicable results in one of the basic domains studied in the literature.

  19. Kinetic and thermodynamic studies of sulforaphane adsorption on macroporous resin.

    PubMed

    Yuanfeng, Wu; Lei, Zhang; Jianwei, Mao; Shiwang, Liu; Jun, Huang; Yuru, You; Lehe, Mei

    2016-08-15

    The adsorption equilibrium, kinetic and thermodynamic of sulforaphane (SF) adsorption onto macroporous resin in aqueous phase were studied. The SP850 resin was screened as the appropriate resin for SF purification. From the equilibrium studies, the Redlich-Peterson model was found to be the best for description of the adsorption behavior of SF onto SP850 resin, followed by the Freundlich model and the Langmuir model. Batch equilibrium experiments demonstrated that, in the examined temperature range, the equilibrium adsorption capacity of SP850 resin decreased with increasing adsorption temperature. Thermodynamics studies indicated that the adsorption of SF was a physical, exothermic, and spontaneous process. The adsorption kinetics revealed that the pseudo-second-order kinetic model was suitable to characterize the kinetics of adsorption of SF onto SP850. Finally, the intra-particle diffusion model demonstrated that SF diffused quickly into macropores, and that diffusion slowed down in the meso- and micropores. PMID:27391585

  20. Novel tannin-based adsorbent in removing cationic dye (Methylene Blue) from aqueous solution. Kinetics and equilibrium studies.

    PubMed

    Sánchez-Martín, J; González-Velasco, M; Beltrán-Heredia, J; Gragera-Carvajal, J; Salguero-Fernández, J

    2010-02-15

    Natural tannin-based adsorbent has been prepared on the basis of the gelification of Quebracho bark extract. The resulting product, Quebracho Tannin Gel (QTG) was tested as cationic dye adsorbent with Methylene Blue (MB). Kinetics of adsorption process were studied out and a period of 15 days was determined for reaching equilibrium. The influences of pH and temperature were evaluated. As pH or temperature raise q capacity of QTG increases. Theoretical modelization of dye-QTG adsorption was carried out by multiparametric adjustment according to Langmuir's hypothesis. Values of the k(l1), k(l2) and activation energies were calculated. PMID:19782466

  1. Helical equilibrium

    SciTech Connect

    Yoshikawa, S.

    1981-08-01

    A straight, helical plasma equilibrium equation is solved numerically for a plasma with a helical magnetic axis. As is expected, by a suitable choice of the plasma boundary, the vacuum configuration is made line ..integral.. dl/B stable. As the plasma pressure increases, the line ..integral.. dl/B criterion will improve (again as expected). There is apparently no limit on the plasma ..beta.. from the equilibrium consideration. Thus helical-axis stellarator ..beta.. will presumably be limited by MHD stability ..beta.., and not by equilibrium ..beta...

  2. Adsorption and isotopic fractionation of Xe

    NASA Technical Reports Server (NTRS)

    Bernatowicz, T. J.; Podosek, F. A.

    1986-01-01

    A theoretical description of the mechanisms of isotopic fractionation arising during adsorption of noble gases in a Henry's Law pressure regime is given. Experimental data on the isotopic composition of Xe adsorbed on activated charcoal in the temperature range 220 K to 350 K are presented. Both theoretical considerations and the experimental data indicate that equilibrium adsorption does not significantly alter the isotopic structure of adsorbed structure of adsorbed noble gases. Therefore, if adsorption is responsible for the elemental noble gas pattern in meteorites and the earth, the heavy noble gas isotopic fractionation between them must have been produced prior to and by a different process than equilibrium adsorption.

  3. Characterization and adsorption properties of a lanthanum-loaded magnetic cationic hydrogel composite for fluoride removal.

    PubMed

    Dong, Shuoxun; Wang, Yili

    2016-01-01

    In this study, a novel lanthanum-loaded magnetic cationic hydrogel (MCH-La) was synthesized for fluoride adsorption from drinking water. The adsorption kinetics, isotherms, and effects of pH and co-existing anions on fluoride uptake by MCH-La were evaluated. FTIR, Raman and XPS were used to analyze the fluoride adsorption mechanism of MCH-La. Results showed that MCH-La had positive zeta potential values of 23.6-8.0 mV at pH 3.0-11.0, with the magnitude of saturation magnetization up to 10.3 emu/g. The fluoride adsorption kinetics by MCH-La fitted well with the fractal-like-pseudo-second-order model, and the adsorption capacity reached 93% of the ultimate adsorption capacity within the first 10 min. The maximum fluoride adsorption capacity for MCH-La was 136.78 mg F(-)/g at an equilibrium fluoride concentration of 29.3 mg/L and pH 7.0. Equilibrium adsorption data showed that the Sips model was more suitable than the Langmuir and Freundlich models. MCH-La still had more than 100 mg of F(-)/g adsorption capacity at a strongly alkaline solution (pH > 10). The adsorption process was highly pH-dependent, and the optimal adsorption was attained at pH 2.8-4.0, corresponding to ligand exchange, electrostatic interactions, and Lewis acid-base interactions. With the exception of both anions of HCO3(-) and SiO4(4-), Cl(-), NO3(-), and SO4(2-) did not evidently prevent fluoride removal by MCH-La at their real concentrations in natural groundwater. The fluoride adsorption capacity of the regenerated MCH-La approached 70% of the fresh MCH-La from the second to fifth recycles. FTIR and Raman spectra revealed that C-O and CO functional groups on MCH contributed to the fluoride adsorption, this finding was also confirmed by the XPS F 1s spectra. Deconvolution of C 1s spectra before and after fluoride adsorption indicated that the carboxyl, anhydride, and phenol groups of MCH were involved in the fluoride removal. PMID:26613180

  4. The adsorption of HCl on volcanic ash

    NASA Astrophysics Data System (ADS)

    Gutiérrez, Xochilt; Schiavi, Federica; Keppler, Hans

    2016-03-01

    data provided here, the gas compositions in equilibrium with the ash surfaces can be calculated. In particular, for dacitic composition, the molar ratio of S/Cl adsorbed to the ash surface is related to the molar S/Cl ratio in the gas phase according to the equation ln ⁡(S / Cl) adsorbed = 2855T-1 + 0.28 ln ⁡(S / Cl) gas - 11.14. Our data also show that adsorption on ash will significantly reduce the fraction of HCl reaching the stratosphere, only if the initial HCl content in the volcanic gas is low (<1 mol%). For higher initial HCl concentrations, adsorption on ash has only a minor effect. While HCl scavenging by hydrometeors may remove a considerable fraction of HCl from the eruption column, recent models suggest that this process is much less efficient than previously thought. Our experimental data therefore support the idea that the HCl loading from major explosive eruptions may indeed cause severe depletions of stratospheric ozone.

  5. EVALUATING MULTICOMPONENT COMPETITIVE ADSORPTION IN FIXED BEDS

    EPA Science Inventory

    An equilibrium column model (ECM) was developed to evaluate multicomponent competition in fixed-bed adsorption columns. The model ignores mass transfer resistances and uses ideal adsorbed solution theory to predict the competitive effects in multicomponent mixtures. The bed capac...

  6. Multilayer adsorption of Cu(II) and Cd(II) over Brazilian Orchid Tree (Pata-de-vaca) and its adsorptive properties

    NASA Astrophysics Data System (ADS)

    Jorgetto, Alexandre de O.; da Silva, Adrielli C. P.; Wondracek, Marcos H. P.; Silva, Rafael I. V.; Velini, Edivaldo D.; Saeki, Margarida J.; Pedrosa, Valber A.; Castro, Gustavo R.

    2015-08-01

    Through very simple and inexpensive processes, pata-de-vaca leaves were turned into a powder and applied as an adsorbent for the uptake of Cu(II) and Cd(II) from water. The material was characterized through SEM, EDX, FTIR and surface area measurement. The material had its point of zero charge determined (5.24), and its adsorption capacity was evaluated as a function of time, pH and metal concentration. The material presented fast adsorption kinetics, reaching adsorption equilibrium in less than 5 min and it had a good correlation with the pseudo-second order kinetic model. Optimum pH for the adsorption of Cu(II) and Cd(II) were found to be in the range from 4 to 5, approximately. In the experiment as a function of the analyte concentration, analogously to gas adsorption, the material presented a type II isotherm, indicating the formation of multilayers for both species. Such behavior was explained with basis in the alternation between cations and anions over the material's surface, and the maximum adsorption capacity, considering the formation of the multilayers were found to be 0.238 mmol L-1 for Cu(II) and 0.113 mmol L-1 for Cd(II).

  7. Size dependent adsorption on nanocrystal surfaces

    NASA Astrophysics Data System (ADS)

    Lu, H. M.; Wen, Z.; Jiang, Q.

    2005-03-01

    A quantitative thermodynamic correlation method to describe the size dependent Langmuir adsorption isotherm is developed. According to the model, the equilibrium adsorption constant increases as material size decreases, which is in agreement with the literature data of acetic acid, valeric acid, oxalic acid, and adipic acid on anatase nanoparticles.

  8. CBOs: Reaching the Hardest to Reach.

    ERIC Educational Resources Information Center

    BCEL Newsletter for the Business Community, 1986

    1986-01-01

    The agents most successful in reaching and teaching those most in need of basic skills instruction are the community-based organizations (CBOs). They come into being in response to social and economic problems faced by their constituents--disadvantaged minorities, the poor, the unemployed, and the alienated. Because of their close ties to the…

  9. Influence of Soil Solution Salinity on Molybdenum Adsorption by Soils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Molybdenum (Mo) adsorption on five arid-zone soils from California was investigated as a function of equilibrium solution Mo concentration (0-30 mg L-1), solution pH (4-8), and electrical conductivity (EC = 0.3 or 8 dS m-1). Molybdenum adsorption decreased with increasing pH. An adsorption maximum...

  10. Removal of phenol from aqueous solutions by adsorption.

    PubMed

    Roostaei, Nadia; Tezel, F Handan

    2004-02-01

    Experiments have been conducted to examine the liquid-phase adsorption of phenol from water by silica gel, HiSiv 3000, activated alumina, activated carbon, Filtrasorb-400, and HiSiv 1000. Experiments were carried out for the analysis of adsorption equilibrium capacities and kinetics. The adsorption isotherm model of the Langmuir-Freundlich type was the best to describe adsorption equilibrium data for phenol for the adsorbents studied. Results of kinetic experiments indicated that HiSiv 1000 had the highest rate of adsorption among the adsorbents studied and therefore more detailed studies were carried out with this adsorbent. The influence of particle size, temperature, and thermal regeneration on adsorption of phenol by HiSiv 1000 was evaluated. From particle size experiments it appeared that adsorption capacity of HiSiv 1000 did not change by changing the particle size, but the rate of adsorption decreased considerably by increasing the particle size. The effect of temperature on adsorption was studied by determining equilibrium isotherms for HiSiv 1000 at 25, 40, and 55 degrees C. The results showed that adsorption capacity decreased with increasing temperature. Thermal regeneration of HiSiv 1000 was performed at 360 degrees C. It was observed that adsorption capacity of HiSiv 1000 did not change after 14 regeneration cycles. Equilibrium experiments showed that the adsorption capacities of activated carbon and Filtrasorb-400 were several times higher than that of HiSiv 1000. PMID:15160741

  11. Enhanced fluoride adsorption by nano crystalline γ-alumina: adsorption kinetics, isotherm modeling and thermodynamic studies

    NASA Astrophysics Data System (ADS)

    Chinnakoti, Prathibha; Chunduri, Avinash L. A.; Vankayala, Ranganayakulu K.; Patnaik, Sandeep; Kamisetti, Venkataramaniah

    2016-06-01

    Nano materials in particular nano oxides with enhanced surface area and an excellent catalytic surface serve as potential adsorbents for defluoridation of water. In the present study nano γ-alumina was synthesized through a simple and low cost, surfactant assisted solution combustion method. As synthesized material was characterized by XRD and FESEM for its phase, size and morphological characteristics. Surface properties have been investigated by BET method. Nano γ-alumina was further used for a detailed adsorption study to remove fluoride from water. Batches of experiments were performed at various experimental conditions such as solution pH, adsorbent dose, initial fluoride concentration and contact time to test the defluoridation ability of γ-alumina. Fluoride Adsorption by nano sized γ-alumina was rapid and reached equilibrium within two hours. The adsorption worked well at pH 4.0, where ˜96 % of fluoride was found to be adsorbed on adsorbent. It was possible to reduce fluoride levels to as low as 0.3 mg/L (within the safe limit of WHO: ≤1.5 mg/L) from an initial fluoride levels of 10 mg/L. This could be achieved using a very small quantity, 1 g/L of γ-alumina at pH 4 within 1 h of contact time. Defluoridation capacity of nano γ-alumina was further investigated by fitting the equilibrium data to various isotherm as well as kinetic models. The present study revealed that γ-alumina could be an efficient adsorbent for treating fluoride contaminated water.

  12. Synthesis, Characterization and Adsorption Properties of Magnetic γ-Fe2O3/C Nanocomposite.

    PubMed

    Mao, Gui-Yun; Bu, Fan-Xing; Jiang, Dong-Mei; Zhao, Zhen-Jie; Zhang, Qing-Hong; Jiang, Ji-Sen

    2015-08-01

    γ-Fe2O3/C nanocomposite was prepared through a convenient method by which one-pot synthesized Fe3O4/Starch was oxidized and carbonized by calcining at 250 °C. The γ-Fe2O3/C displayed strong magnetism and could adsorb organic molecules from aqueous solution effectively, thus it showed promising application in the dislodgement of organic pollutants in sewage. Adsorption isotherms and kinetics of methylene blue (MB) onto γ-Fe2O3/C were studied in a batch system. The adsorption process reached equilibrium in about 15 min, and the maximum adsorption capacity of MB was found to be 64.9 mg g-1 at 303 K. Adsorption isotherms were well fitted to Langmuir model and the adsorption kinetics could be described by the pseudo-second order kinetic equation. The findings of the present work highlight a new facile method to fabricate magnetic carbon-based composites and the obtained γ-Fe2O3/C with excellent magnetic property and adsorption performance hold great promise for practical application in water treatment. PMID:26369173

  13. Investigation of the adsorption of water vapor and carbon dioxide by KA zeolite

    SciTech Connect

    Khanitonov, V.P.; Shtein, A.S.

    1984-05-01

    According to the present data, KA zeolite, which can adsorb only water vapor, helium, and hydrogen, has the greatest selectivity in drying. The feasibility of using this zeolite in devices for selective drying of gases used in gas-analysis systems was studied. The results of the experiments were approximated by the thermal equation of the theory of bulk filling of micropores. The limiting value of the adsorption depends on the temperature, and it can be calculated according to the density of the adsorbed phase and the adsorption volume. The critical diameters of the water and carbon dioxide molecules are close to the dimensions of the KA-zeolite pores, something that determines the activated nature of the adsorption of these substances. Experiments on coadsorption of water vapor and carbon dioxide by a fixed bed of KA-zeolite under dynamic conditions showed that the adsorption of these substances has a frontal nature. The time of the protective action of the layer of zeolite during adsorption af water vapor exceeded by more than an order the time of the protective action during adsorption of carbon dioxide. The results showed that this adsorbent can be used for selective drying of gas mixtures containing carbon dioxide in batch-operation devices. Beforehand, the adsorbent should be regenerated with respect to moisture, and then it should be saturated with carbon dioxide by blowing the adsorbent with a gas mixture of the working composition until the equilibrium state is reached.

  14. Application of a new bifunctionalized chitosan derivative with zwitterionic characteristics for the adsorption of Cu(2+), Co(2+), Ni(2+), and oxyanions of Cr(6+) from aqueous solutions: Kinetic and equilibrium aspects.

    PubMed

    de Almeida, Francine Tatiane Rezende; Ferreira, Bruno Christiano Silva; Moreira, Ana Luísa da Silva Lage; de Freitas, Rossimiriam Pereira; Gil, Laurent Frédéric; Gurgel, Leandro Vinícius Alves

    2016-03-15

    This study describes the synthesis of a new chitosan derivative (C2) with zwitterionic characteristics and its use for the removal of cationic species Cu(2+), Co(2+), and Ni(2+) and anionic species of Cr(6+) in a single aqueous solution. The new adsorbent was synthesized by quaternization of the amine group of chitosan and esterification of hydroxyl groups with EDTA dianhydride. These combined reactions gave both cationic and anionic characteristics to C2 with the release of quaternary ammonium groups and carboxylic groups. The capacity of C2 to adsorb Cu(2+), Co(2+), Ni(2+), and oxyanions of Cr(6+) was evaluated in a batch process with different contact times, pH values, and initial concentrations. Adsorption isotherms were best fitted to the Langmuir and Sips models. The maximum adsorption capacities (Q(max)) of C2 for adsorption of Cu(2+), Co(2+), Ni(2+), and Cr(6+) were 0.698, 1.125, 0.725, and 1.910 mmol/g, respectively. The Δ(ads)G° values were in the range from -20 to -28 kJ/mol. These values suggest a mixed mechanism controlling adsorption. Desorption studies using an aqueous solution consisting of 0.1 mol/L HNO3 were carried out. The reusability of the recovered C2 adsorbent after desorption was also evaluated. PMID:26748062

  15. Adsorption of Cu(2+), Cd(2+) and Ni(2+) from aqueous single metal solutions on graphene oxide membranes.

    PubMed

    Tan, Ping; Sun, Jian; Hu, Yongyou; Fang, Zheng; Bi, Qi; Chen, Yuancai; Cheng, Jianhua

    2015-10-30

    Novel, highly ordered layered graphene oxide (GO) membranes with larger interlayer spacing were prepared by induced directional flow and were used as adsorbents for the removal of Cu(2+), Cd(2+) and Ni(2+) from aqueous solutions. The effects of pH, ionic strength, contact time, metal ion concentration and cycle time on Cu(2+), Cd(2+) and Ni(2+) sorption were investigated. The results indicated that the adsorption of Cu(2+), Cd(2+) and Ni(2+) onto GO membranes was greatly influenced by the pH and weakly affected by the ionic strength. The adsorption isotherms for Cu(2+), Cd(2+) and Ni(2+) were well fitted by the Langmuir model. The maximum adsorption capacities of the GO membranes for Cu(2+), Cd(2+) and Ni(2+) were approximately 72.6, 83.8 and 62.3 mg/g, respectively. The adsorption kinetics of Cu(2+), Cd(2+) and Ni(2+) onto GO membranes followed the pseudo-second-order model. The adsorption equilibrium was reached in a shorter time. The GO membranes can be regenerated more than six times based on their adsorption/desorption cycles, with a slight loss in the adsorption capacity. The results demonstrated that the GO membranes can be used as effective adsorbents for heavy metal removal from water. PMID:25978188

  16. Adsorption-desorption and leaching behavior of kresoxim-methyl in different soils of India: kinetics and thermodynamic studies.

    PubMed

    Sabale, Rupali P; Shabeer T P, Ahammed; Dasgupta, Soma; Utture, Sagar C; Banerjee, Kaushik; Oulkar, Dasharath P; Adsule, Pandurang G; Deshmukh, Madhukar B

    2015-07-01

    The sorption and leaching behavior of kresoxim-methyl was explored in four different soils, viz., clay, sandy loam, loamy sand, and sandy loam (saline), representing vegetables and fruits growing regions of India. Adsorption of kresoxim-methyl in all the soils reached equilibrium within 48 h. The rate constants for adsorption and desorption at two different temperatures were obtained from the Lindstrom model, which simultaneously evaluated adsorption and desorption kinetics. The data for rate constants, activation energies, enthalpy of activation, entropy of activation, and free energy indicated physical adsorption of kresoxim-methyl on soil. The relative adsorptivity of the test soils could be attributed to different organic matter and clay contents of the soils. A good fit to the linear and Freundlich isotherms was observed for both adsorption as well as desorption. The groundwater ubiquity score (GUS) for different soils varied between 0 and 2.26. The GUS and leaching study indicated moderately low leaching potential of kresoxim-methyl. The adsorption on four soil types largely depended on the soil physicochemical properties such as organic carbon content, cation-exchange capacity, and texture of the soil. PMID:26082423

  17. Adsorption behavior and mechanism of chloramphenicols, sulfonamides, and non-antibiotic pharmaceuticals on multi-walled carbon nanotubes.

    PubMed

    Zhao, Heng; Liu, Xue; Cao, Zhen; Zhan, Yi; Shi, Xiaodong; Yang, Yi; Zhou, Junliang; Xu, Jiang

    2016-06-01

    The adsorption behavior of different emerging contaminants (3 chloramphenicols, 7 sulfonamides, and 3 non-antibiotic pharmaceuticals) on five types of multi-walled carbon nanotubes (MWCNTs), and the underlying factors were studied. Adsorption equilibriums were reached within 12h for all compounds, and well fitted by the Freundlich isotherm model. The adsorption affinity of pharmaceuticals was positively related to the specific surface area of MWCNTs. The solution pH was an important parameter of pharmaceutical adsorption on MWCNTs, due to its impacts on the chemical speciation of pharmaceuticals and the surface electrical property of MWCNTs. The adsorption of ionizable pharmaceuticals decreased in varying degrees with the increased ionic strength. MWCNT-10 was found to be the strongest adsorbent in this study, and the Freundlich constant (KF) values were 353-2814mmol(1-n)L(n)/kg, 571-618mmol(1-n)L(n)/kg, and 317-1522mmol(1-n)L(n)/kg for sulfonamides, chloramphenicols, and non-antibiotic pharmaceuticals, respectively. The different adsorption affinity of sulfonamides might contribute to the different hydrophobic of heterocyclic substituents, while chloramphenicols adsorption was affected by the charge distribution in aromatic rings via substituent effects. PMID:26937870

  18. Equilibrium Shaping

    NASA Astrophysics Data System (ADS)

    Izzo, Dario; Petazzi, Lorenzo

    2006-08-01

    We present a satellite path planning technique able to make identical spacecraft aquire a given configuration. The technique exploits a behaviour-based approach to achieve an autonomous and distributed control over the relative geometry making use of limited sensorial information. A desired velocity is defined for each satellite as a sum of different contributions coming from generic high level behaviours: forcing the final desired configuration the behaviours are further defined by an inverse dynamic calculation dubbed Equilibrium Shaping. We show how considering only three different kind of behaviours it is possible to acquire a number of interesting formations and we set down the theoretical framework to find the entire set. We find that allowing a limited amount of communication the technique may be used also to form complex lattice structures. Several control feedbacks able to track the desired velocities are introduced and discussed. Our results suggest that sliding mode control is particularly appropriate in connection with the developed technique.

  19. Adsorption of polymeric brushes: Bridging

    NASA Astrophysics Data System (ADS)

    Johner, Albert; Joanny, Jean-François

    1992-04-01

    We study the adsorption of grafted polymer layers on a planar surface parallel to the grafting surface. The layer consists of two types of chains: nonadsorbed chains with a free end and adsorbed chains forming bridges between the two plates. In the limit of strong adsorption a dead zone exists in the vicinity of the adsorbing plate; its size increases with the adsorption strength. Two adsorption mechanisms are possible: adsorption of the last monomer only and adsorption of all the monomers. In both cases the adsorption regimes at equilibrium (when no external force acts on the plates) are discussed within the framework of the self-consistent mean-field theory. We also give scaling laws taking into account excluded volume correlations. Finally, we consider situations where a finite external force, either tangential or normal to the plates, is applied on the adsorbing plate. Pulling and tangential forces both reduce the fraction of bridges and eventually lead to rupture, whereas compressional forces favor bridging. For normal forces, force vs distance profiles between planes and crossed cylinders are given.

  20. Hexavalent chromium removal performance of anionic functionalized monolithic polymers: column adsorption, regeneration and modelling.

    PubMed

    Barlik, Necla; Keskinler, Bülent; Kocakerim, M Muhtar

    2016-01-01

    Anionic functionalized monolithic macro-porous polymers were used for the removal of hexavalent chromium(VI) anions from aqueous solution in column experiments. At a flux of 1.0 cm min and 30 mg Cr(VI) L(-1) feed concentration, breakthrough capacity and apparent capacity were 0.066 g Cr(VI) g(-1) anionic monolith and 0.144 g Cr(VI) g(-1) anionic monolith, respectively. The degree of column utilization was found to lie in the range 41-46%. Two kinetic models, theoretical and Thomas models, were applied to experimental data to predict the breakthrough curves and to determine the characteristic parameters of the column useful for process design. The simulation of the whole breakthrough curve was effective with the models. At a flux of 1.0 cm min and 30 mg Cr(VI) L(-1) feed concentration, the dispersion coefficient and adsorption equilibrium constant (K) were 3.14 × 10(-7) m s(-1) and 3,840, respectively. Also, Thomas model parameters k1 (rate constant of adsorption) and qm (equilibrium solid-phase concentration of sorbed solute) were 1.08 × 10(-3) L mg(-1) min(-1) and 0.124 g g(-1), respectively. After reaching equilibrium adsorption capacity, the monoliths were regenerated using 1 N HCl and were subsequently re-tested. It was found that the regeneration efficiency reduced from 98% after second usage to 97% after the third usage. PMID:27003067

  1. Preparation, Characterization and Application of Magnetic Fe3O4-CS for the Adsorption of Orange I from Aqueous Solutions

    PubMed Central

    Du, Yankai; Pei, Meishan; He, Youjun; Yu, Faqi; Guo, Wenjuan; Wang, Luyan

    2014-01-01

    Fe3O4 (Fe3O4-CS) coated with magnetic chitosan was prepared as an adsorbent for the removal of Orange I from aqueous solutions and characterized by FTIR, XRD, SEM, TEM and TGA measurements. The effects of pH, initial concentration and contact time on the adsorption of Orange I from aqueous solutions were investigated. The decoloration rate was higher than 94% in the initial concentration range of 50–150 mg L−1 at pH 2.0. The maximum adsorption amount was 183.2 mg g−1 and was obtained at an initial concentration of 400 mg L−1 at pH 2.0. The adsorption equilibrium was reached in 30 minutes, demonstrating that the obtained adsorbent has the potential for practical application. The equilibrium adsorption isotherm was analyzed by the Freundlich and Langmuir models, and the adsorption kinetics were analyzed by the pseudo-first-order and pseudo-second-order kinetic models. The higher linear correlation coefficients showed that the Langmuir model (R2 = 0.9995) and pseudo-second-order model (R2 = 0.9561) offered the better fits. PMID:25271644

  2. Adsorption of drinking water fluoride on a micron-sized magnetic Fe3O4@Fe-Ti composite adsorbent

    NASA Astrophysics Data System (ADS)

    Zhang, Chang; Li, Yingzhen; Wang, Ting-Jie; Jiang, Yanping; Wang, Haifeng

    2016-02-01

    A micron-sized magnetic adsorbent (MMA) for fluoride removal from drinking water was prepared by spray drying and subsequent calcination of a magnetic Fe3O4@Fe-Ti core-shell nanoparticle slurry. The MMA granules had high mechanical strength and stability against water scouring, can be easily separated from the water by a magnet, and had a high selectivity for fluoride versus common co-existing ions and high fluoride removal efficiency in a wide range of initial pH of 3-11. Abundant hydroxyl groups on the MMA surface acted as the active sites for fluoride adsorption, which resulted in a high affinity of the MMA for fluoride. The pH in the adsorption process affected the adsorption significantly. At neutral initial pH, the adsorption isotherm was well fitted with the Langmuir model, and the maximum adsorption capacity reached a high value of 41.8 mg/g. At a constant pH of 3, multilayer adsorption of fluoride occurred due to the abundant positive surface charges on the MMA, and the adsorption isotherm was well fitted with the Freundlich model. The MMA had a fast adsorption rate, and adsorption equilibrium was achieved within 2 min. The adsorption kinetics followed a quasi-second order model. The regeneration of the MMA was easy and fast, and can be completed within 2 min. After 10 recycles, the fluoride removal efficiency of the MMA still remained high. These properties showed that the MMA is a promising adsorbent for fluoride removal.

  3. Adsorption of Cu(II) on Oxidized Multi-Walled Carbon Nanotubes in the Presence of Hydroxylated and Carboxylated Fullerenes

    PubMed Central

    Wang, Jing; Li, Zhan; Li, Shicheng; Qi, Wei; Liu, Peng; Liu, Fuqiang; Ye, Yuanlv; Wu, Liansheng; Wang, Lei; Wu, Wangsuo

    2013-01-01

    The adsorption of Cu(II) on oxidized multi-walled carbon nanotubes (oMWCNTs) as a function of contact time, pH, ionic strength, temperature, and hydroxylated fullerene (C60(OH)n) and carboxylated fullerene (C60(C(COOH)2)n) were studied under ambient conditions using batch techniques. The results showed that the adsorption of Cu(II) had rapidly reached equilibrium and the kinetic process was well described by a pseudo-second-order rate model. Cu(II) adsorption on oMWCNTs was dependent on pH but independent of ionic strength. Compared with the Freundlich model, the Langmuir model was more suitable for analyzing the adsorption isotherms. The thermodynamic parameters calculated from temperature-dependent adsorption isotherms suggested that Cu(II) adsorption on oMWCNTs was spontaneous and endothermic. The effect of C60(OH)n on Cu(II) adsorption of oMWCNTs was not significant at low C60(OH)n concentration, whereas a negative effect was observed at higher concentration. The adsorption of Cu(II) on oMWCNTs was enhanced with increasing pH values at pH < 5, but decreased at pH ≥ 5. The presence of C60(C(COOH)2)n inhibited the adsorption of Cu(II) onto oMWCNTs at pH 4–6. The double sorption site model was applied to simulate the adsorption isotherms of Cu(II) in the presence of C60(OH)n and fitted the experimental data well. PMID:24009683

  4. Equilibrium ignition for ICF capsules

    SciTech Connect

    Lackner, K.S.; Colgate, S.A.; Johnson, N.L.; Kirkpatrick, R.C.; Menikoff, R.; Petschek, A.G.

    1993-12-31

    There are two fundamentally different approaches to igniting DT fuel in an ICF capsule which can be described as equilibrium and hot spot ignition. In both cases, a capsule which can be thought of as a pusher containing the DT fuel is imploded until the fuel reaches ignition conditions. In comparing high-gain ICF targets using cryogenic DT for a pusher with equilibrium ignition targets using high-Z pushers which contain the radiation. The authors point to the intrinsic advantages of the latter. Equilibrium or volume ignition sacrifices high gain for lower losses, lower ignition temperature, lower implosion velocity and lower sensitivity of the more robust capsule to small fluctuations and asymmetries in the drive system. The reduction in gain is about a factor of 2.5, which is small enough to make the more robust equilibrium ignition an attractive alternative.

  5. Investigation of the effect of magnetic particles on the Crystal Violet adsorption onto a novel nanocomposite based on κ-carrageenan-g-poly(methacrylic acid).

    PubMed

    Gholami, Mostafa; Vardini, Mohammad Taghi; Mahdavinia, Gholam Reza

    2016-01-20

    A novel nanocomposite hydrogel prepared by incorporating Fe3O4 magnetic nanoparticles into the κ-carrageenan-g-poly (methacrylic acid) with in situ polymerization and was characterized by FT-IR, XRD, SEM, TEM and VSM. Synthesized nanocomposite was used to adsorb Crystal Violet (CV) (cationic dye) in aqueous solution in a batch system. The research studies showed that the adsorption of CV can be impressed as a function of contact time, initial concentration of CV, pH and molar ratio of κ-carrageenan to poly(methacrylic acid). CV adsorption tests disclosed that it only takes 15 min to reach the equilibrium and adsorption capacity for this dye was 28.24 mg g(-1). Langmuir isotherm for equilibrium adsorption data was fitted well and the pseudo-second-order model can describe the adsorption kinetics. Thermodynamic parameters of ΔG°, ΔH° and ΔS° showed the endothermic nature of adsorption and a spontaneous process. PMID:26572412

  6. Facile Synthesis of Prussian Blue Derivate-Modified Mesoporous Material via Photoinitiated Thiol-Ene Click Reaction for Cesium Adsorption.

    PubMed

    Qian, Jun; Ma, Jiaqi; He, Weiwei; Hua, Daoben

    2015-08-01

    A novel strategy to synthesize a functional mesoporous material for efficient removal of cesium is reported. Specifically, Prussian blue derivate-modified SBA-15 (SBA-15@FC) was prepared by photoinitiated thiol-ene reaction between thiol-modified SBA-15 and pentacyano(4-vinyl pyridine)ferrate complex. The effects of weight percentage of the Prussian blue derivate, pH, adsorbent dose, co-existing ions, and initial concentration were evaluated on the adsorption of cesium ions. The adsorption kinetically follows a pseudo-second-order model and reaches equilibrium within 2 h with a high adsorption capacity of about 13.90 mg Cs g(-1) , which indicates that SBA-15@FC is a promising adsorbent to effectively remove cesium from aqueous solutions. PMID:25965318

  7. Adsorption behaviour of bulgur.

    PubMed

    Erbaş, Mustafa; Aykın, Elif; Arslan, Sultan; Durak, Atike N

    2016-03-15

    The aim of this research was to determine the adsorption behaviour of bulgur. Three different particle sizes (2equilibrium levels of relative humidity (8.2-97.3%) at 20, 30 and 40 °C. The data obtained were evaluated using BET (Brunauer-Emmett-Teller) and GAB (Guggenheim, Anderson and deBoer) sorption equations. The equilibrium moisture content of bulgur increased both with decreasing temperature and bulgur size. The constants m0 and C of BET and GAB equations were determined to be between 2.54 and 5.03 g water per 100 g of dry matter and 4.96-16.57, respectively. Constant k was between 0.85 and 0.93, and GAB equation was determined to fit very well for bulgur adsorption, because of %E values lower than 10%. Bulgur must be stored below 70% relative humidity and with less than 10 g water per 100 g of dry mater. PMID:26575716

  8. Removal of Cr(VI) from aqueous solutions by adsorption on MnO2.

    PubMed

    Gheju, Marius; Balcu, Ionel; Mosoarca, Giannin

    2016-06-01

    Adsorption of Cr(VI) on MnO2 was investigated with respect to effect of pH, temperature, ionic strength, initial Cr(VI) concentration, co-presence of different anions (HCO3(-), SO4(2-), H2PO4(-), NO3(-) and Cl(-)) and of low molecular weight natural organic materials (LMWNOM) (acetate, oxalate and citrate). The process was rapid during the first 3-5min, reaching equilibrium after one hour. Adsorption decreased with increasing pH, temperature and Cr(VI) initial concentration, and increased with increasing ionic strength. Co-presence of phosphate, sulfate, bicarbonate, citrate and oxalate hindered Cr(VI) adsorption, whereas nitrate, chloride and acetate did not exert any notable influence. The overall order of Cr(VI) adsorption suppression due to co-presence of anions and LMWNOM was H2PO4(-)>HCO3(-)>SO4(2-), and oxalate>citrate, respectively. Highest experimental equilibrium sorption capacity (0.83mgg(-1)) was obtained at 20°C and pH 5.9, while lowest (0.18mgg(-1)) was noticed in the co-presence of H2PO4(-), at 20°C and pH 6.9. Adsorption kinetics was successfully fitted by pseudo-second-order model. Mechanisms for both specific and non-specific adsorption are likely to be involved, while rate-controlling step involved both intra-particle and film diffusion processes. Cr(VI) was strongly bound to MnO2, which makes risks of its subsequent liberation into the environment to be low. PMID:26947189

  9. Adsorption of four perfluorinated acids on non ion exchange polymer sorbents.

    PubMed

    Senevirathna, S T M L D; Tanaka, S; Fujii, S; Kunacheva, C; Harada, H; Shivakoti, B R; Dinh, H; Ariyadasa, T

    2011-01-01

    Perfluorinated compounds (PFCs) have attracted global concern due to their ubiquitous distribution and properties of persistence, bio accumulation and toxicity. The process of adsorption has been identified as an effective technique to remove PFCs in water. Different non ion-exchange polymeric adsorbents were tested with regard to their sorption kinetics and isotherms at low PFCs concentrations. Selected PFCs were perfluorobutanoic acid (PFBA), perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA) and perfluorodecanoic acid (PFDA) and the tested polymers were three types of Dowex optopores (V-493, V503, and L493), Amberlite XAD-4, and Filtrasorb 400 (Granular Activated Carbon-GAC). We observed the selective adsorption of PFCs on synthetic polymers. For PFDA, Amberlite XAD-4 gave the Freundlich adsorption constant of 2,965 (microg PFCs/g sorbent)(microg PFCs/L)(-n), which was higher than that of GAC (121.89 (microg PFCs/g sorbent) (microg PFCS/L)(-n)). In the case of PFBA, GAC showed better performance (13.36) (microg PFCs/g sorbent) microg PFCS/L)(-n) than synthetic polymers (0.62-5.23) (microg PFCs/g sorbent) (microg PFCS/L)(-n). Adsorption kinetics of all adsorbents were well described (R2 = 0.85-1) by pseudo-second order kinetic model. Sorption capacity was influenced by initial PFCs concentration for all adsorbents. GAC reached the equilibrium concentration within 4 hours, Amberlite XAD 4 reached it within 10 hours and other polymers took more than 70 hours. PMID:21977627

  10. Recycling cellulases by pH-triggered adsorption-desorption during the enzymatic hydrolysis of lignocellulosic biomass.

    PubMed

    Shang, Yaping; Su, Rongxin; Huang, Renliang; Yang, Yang; Qi, Wei; Li, Qiujin; He, Zhimin

    2014-06-01

    Recycling of cellulases is an effective way to reduce the cost of enzymatic hydrolysis for the production of cellulosic ethanol. In this study, we examined the adsorption and desorption behaviors of cellulase at different pH values and temperatures. Furthermore, we developed a promising way to recover both free and bound cellulases by pH-triggered adsorption-desorption. The results show that acidic pH (e.g., pH 4.8) was found to favor adsorption, whereas alkaline pH (e.g., pH 10) and low temperature (4-37 °C) favored desorption. The adsorption of cellulases reached an equilibrium within 60 min at pH 4.8 and 25 °C, leading to approximately 50 % of the added cellulases bound to the substrate. By controlling the pH of eluent (citrate buffer, 25 °C), we were able to increase the desorption efficiency of bound cellulases from 15 % at pH 4.8 to 85 % at pH 10. To recover cellulases after enzymatic hydrolysis, we employed adsorption by fresh substrate and desorption at pH 10 to recover the free cellulases in supernatant and the bound cellulases in residue, respectively. The recycling performance (based on the glucose yield) of this simple strategy could reach near 80 %. Our results provided a simple, low-cost, and effective approach for cellulase recycling during the enzymatic hydrolysis of lignocellulosic biomass. PMID:24752845

  11. The impact of particle size on the adsorption of citrate to hematite.

    PubMed

    Noerpel, Matthew R; Lenhart, John J

    2015-12-15

    We investigated the adsorption of citric acid on the surface of two different sized hematite nanoparticles using batch adsorption experiments, Fourier-transform infrared spectroscopy, surface complexation modeling and computational molecular modeling. Citrate adsorption reached a maximum between pH approximately 2.5 and 5.5 and declined as the pH was increased or decreased from that range. At high surface loading conditions, the dominant adsorbed citrate structure was outer-sphere in nature with a protonation state that varied with pH. At low pH, there was also evidence of an inner-sphere complex consistent with a binuclear, bidentate structure where the hydroxyl group was deprotonated and played an active role in the adsorption. An inner-sphere complex was also detected at low citrate surface loading conditions. Surface-area normalized surface coverages were similar for both sizes of hematite, however, the inner sphere complex appeared to be slightly more prevalent on the smaller hematite. Based on these structures, a triple layer surface complexation model comprised of two outer-sphere complexes and one inner-sphere complex was used to describe the adsorption data for both hematite sizes across a range of solution conditions with a single set of surface area dependent equilibrium constants. PMID:26313711

  12. Preparation and adsorption performance of MnO2/PAC composite towards aqueous glyphosate.

    PubMed

    Cui, Hao; Li, Qin; Qian, Yan; Zhang, Qiu; Zhai, Jianping

    2012-09-01

    Glyphosate (N-phosphonomethylglycine (PMG)) is the organophosphate herbicide most widely used in the world, and industrial production of PMG generates large quantities of wastewater. A manganese dioxide-coated powdered activated carbon (MnO2/PAC) composite was synthesized and investigated for the adsorption of PMG from wastewater. The results of scanning electron microscopy (SEM) combined with energy-dispersive X-ray spectrometry (EDAX) revealed that MnO2 was formed on the surface of the carbon during the modification process. Batch adsorption results showed that the optimal pH for glyphosate adsorption on MnO2/PAC was 3.0. In the range 0.01(-1) molL(-1), glyphosate removal by MnO2/PAC decreased with an increase in ionic strength. Among the coexistent anions, only phosphate showed significant inhibition of PMG removal due to competitive complexation. Batch studies revealed that MnO2/PAC could reach a maximum PMG adsorption capacity of 283 mg g(-1). The Langmuir equilibrium model was found to be suitable for describing PMG sorption, and kinetic studies revealed that adsorption followed second-order rate kinetics. It was also proved that the adsorbed PMG could be effectively desorbed from MnO2/PAC in 1.0 molL(-1) NaOH. All of these results implied that the MnO2/PAC composite may be used as an effective adsorbent for recycling PMG from wastewater. PMID:23240199

  13. Adsorption of bisphenol A from aqueous solution onto activated carbons with different modification treatments.

    PubMed

    Liu, Guifang; Ma, Jun; Li, Xuchun; Qin, Qingdong

    2009-05-30

    Two commercial carbons (W20 and F20) had been selectively modified with nitric acid and thermal treatment under a flow of N(2) in present study to adsorb bisphenol A from aqueous solution. The results indicated that the experimental data were well described with pseudo-second-order kinetic model. W20 and its thermal modified sample (W20N) represented a better adsorption capacity, and the equilibrium adsorption amounts reached 382.12 and 432.34 mg/g, respectively. Further, effects of temperature, pH and ionic strength on bisphenol A adsorption onto W20 and W20N had been examined. It was found that the adsorbed amount of bisphenol A decreased with the increase of temperature from 288 to 318 K and changed little with the increase of pH from 5.0 to 9.0. At pH 11.0, the two activated carbons represented the weakest adsorption capacity. The adsorption capacities of bisphenol A onto W20 and W20N first decreased and then increased with the increasing of ionic strength. PMID:18977073

  14. Wet oxidation of ordered mesoporous carbon FDU-15 by using (NH4)2S2O8 for fast adsorption of Sr(II): An investigation on surface chemistry and adsorption mechanism

    NASA Astrophysics Data System (ADS)

    Song, Yang; Ye, Gang; Chen, Jing; Lv, Dachao; Wang, Jianchen

    2015-12-01

    Surface modification of ordered mesoporous carbon (OMC) by wet oxidation provides an oxygen-enriched platform for complexation of metal ions. Here, we present a comprehensive study on the surface chemistry and textual property of OMC FDU-15 modified by wet oxidation using (NH4)2S2O8 as a benign oxidant. And, for the first time, the adsorption behavior and mechanism of wet-oxidized OMC FDU-15 toward Sr(II) in aqueous solutions were investigated. The mesostructural regularity of the OMC FDU-15 was well-reserved under wet oxidation. Compared to OMC CMK-type counterparts prepared via nanocasting, the OMC FDU-15 by soft template method showed much-enhanced structural stability. Due to the introduction of abundant oxygen-containing species, the oxidized OMC FDU-15 exhibited excellent hydrophilicity and dispersibility in aqueous solutions. The adsorption behavior toward Sr(II) was fully investigated, showing a super-fast adsorption kinetics (< 5 min to reach equilibrium) and a Langmuir adsorption isotherm. Moreover, an in-depth X-ray photoelectron spectroscopy analysis through deconvolution of high resolution C1s and O1s spectra was implemented to identify the chemical species of the surface functional groups, while probing the adsorption mechanism. The results suggested that oxygen donor atoms in Csbnd O single bonds mainly contribute to the adsorption of Sr(II) via formation of metal-ligand complexation.

  15. Influence of particle size and salinity on adsorption of basic dyes by agricultural waste: dried seagrape (Caulerpa lentillifera).

    PubMed

    Punjongharn, Pimol; Meevasana, Khanidtha; Pavasant, Prasert

    2008-01-01

    Green macroalga Caulerpa lentillifera was found to have reasonable adsorption capacity for basic dyes, Astrazon Blue FGRL (AB), Astrazon Red GTLN (AR), and Astrazon Golden Yellow GL-E (AY). The initial dye concentration was in the range of 100-1,800 mg/L. The dried algal sorbent was ground and sieved into 3 sizes: S (0.1-0.84 mm), M (0.84-2.0 mm), and L sizes (larger than 2.0 mm). For all conditions examined in this work (at 25 degrees C in batch systems), the adsorption reached equilibrium within the first hour. The kinetic data corresponded well with the pseudo second order kinetic model where the rate constant, k2, decreased as the sorbent size increased for all dyes. The adsorption isotherms followed both Langmuir and Freundlich models. Among three sorbent sizes, S size gave the highest adsorption capacity followed by M and L sizes. A reduction of sorbent size increased the specific surface area for mass transfer, and also increased the total pore volume, thus providing more active sites for adsorption. The adsorption of AB was adversely influenced by the protonation of algal surface at low pH. On the other hand, the adsorption of AR and AY could be due to weak electrostatic interaction, which was not significantly affected by pH. Increasing salinity of the system caused a decrease in adsorption capacity possibly due to the competition between Na+ and the dye cations for the binding sites on algal surface. Moreover, an increase in salinity generated a compressed electrical double layer on the algal surface which exerted repulsive force, retarding the adsorption of positive charged molecules such as the basic dyes. PMID:18763573

  16. Adsorption of Cu2+ ions using chitosan-modified magnetic Mn ferrite nanoparticles synthesized by microwave-assisted hydrothermal method

    NASA Astrophysics Data System (ADS)

    Meng, Yuying; Chen, Deyang; Sun, Yitao; Jiao, Dongling; Zeng, Dechang; Liu, Zhongwu

    2015-01-01

    Chitosan-modified Mn ferrite nanoparticles were synthesized by a one-step microwave-assisted hydrothermal method. These Mn ferrite magnetic composite nanoparticles were employed to absorb Cu2+ ions in water. XRD verified the spinel structure of the MnFe2O4 nanoparticles. Chitosan modification does not result in any phase change of MnFe2O4. FTIR and zeta potentials curves for all samples suggest that chitosan can be successfully coated on the Mn ferrites. TEM characterization showed that the modified MnFe2O4 nanoparticles have a cubic shape with a mean diameter of ∼100 nm. For adsorption behavior, the effects of experiment parameters such as solution pH value, contact time and initial Cu2+ ions concentration on the adsorption efficiency were systematically investigated. The results showed that increasing solution pH value and extending contact time are favorable for improving adsorption efficiency. Especially, adsorption efficiency can reach up to 100% and 96.7% after 500 min adsorption at pH 6.5 for the solutions with initial Cu2+ ions concentration of 50 mg/L and 100 mg/L. Adsorption data fits well with the Langmuir isotherm models with a maximum adsorption capacity (qm) and a Langmuir adsorption equilibrium constant (K) of 65.1 mg/g and 0.090 L/mg, respectively. The adsorption kinetic agrees well with pseudo second order model with the pseudo second rate constants (K2) of 0.0468 and 0.00189 g/mg/min for solutions with initial Cu2+ ions of 50 and 100 mg/L, respectively.

  17. REACH. Electricity Units. Secondary.

    ERIC Educational Resources Information Center

    Smith, Gene; Sappe, Hoyt

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of electricity. The instructional units focus on electricity fundamentals and electric motors. Each unit follows a typical format that includes a unit sheet,…

  18. REACH. Heating Units.

    ERIC Educational Resources Information Center

    Stanfield, Carter; And Others

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized units in the area of heating. The instructional units focus on electric heating systems, gas heating systems, and oil burning systems. Each unit follows a typical format that includes a unit…

  19. REACH. Air Conditioning Units.

    ERIC Educational Resources Information Center

    Garrison, Joe; And Others

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of air conditioning. The instructional units focus on air conditioning fundamentals, window air conditioning, system and installation, troubleshooting and…

  20. Reaching for the Stars.

    ERIC Educational Resources Information Center

    Roper-Davis, Sharon

    1999-01-01

    Describes "Reaching for the Stars," a program which develops teaming and mentoring skills in senior physics students. Phase 1 requires student pairs to design a rocket; Phase 2 pairs seniors with gifted second graders who build the rocket from written instructions; and in Phase 3, pairs of seniors create a children's storybook explaining one of…

  1. REACH. Major Appliance.

    ERIC Educational Resources Information Center

    English, Charles; And Others

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of major appliances. The instructional units focus on installation of appliances, troubleshooting washing machines, troubleshooting electric dryers,…

  2. Reaching into Pictorial Spaces

    NASA Astrophysics Data System (ADS)

    Volcic, Robert; Vishwanath, Dhanraj; Domini, Fulvio

    2014-02-01

    While binocular viewing of 2D pictures generates an impression of 3D objects and space, viewing a picture monocularly through an aperture produces a more compelling impression of depth and the feeling that the objects are "out there", almost touchable. Here, we asked observers to actually reach into pictorial space under both binocular- and monocular-aperture viewing. Images of natural scenes were presented at different physical distances via a mirror-system and their retinal size was kept constant. Targets that observers had to reach for in physical space were marked on the image plane, but at different pictorial depths. We measured the 3D position of the index finger at the end of each reach-to-point movement. Observers found the task intuitive. Reaching responses varied as a function of both pictorial depth and physical distance. Under binocular viewing, responses were mainly modulated by the different physical distances. Instead, under monocular viewing, responses were modulated by the different pictorial depths. Importantly, individual variations over time were minor, that is, observers conformed to a consistent pictorial space. Monocular viewing of 2D pictures thus produces a compelling experience of an immersive space and tangible solid objects that can be easily explored through motor actions.

  3. REACH. Refrigeration Units.

    ERIC Educational Resources Information Center

    Snow, Rufus; And Others

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of refrigeration. The instructional units focus on refrigeration fundamentals, tubing and pipe, refrigerants, troubleshooting, window air conditioning, and…

  4. "Brown's" Far Reaching Impact

    ERIC Educational Resources Information Center

    Chinn, Philip C.

    2004-01-01

    Although the 1954 "Brown v. Board of Education" U.S. Supreme Court decision changed the face of American education forever, few individuals at that time could have fully realized its far-reaching implications. Certainly, the National Association for the Advancement of Colored People Legal Director Thurgood Marshall in his arguments was focusing on…

  5. Reaching Your Fitness Goals

    MedlinePlus

    Everyday Fitness Ideas from the National Institute on Aging at NIH www.nia.nih.gov/Go4Life Reaching Your Fitness Goals You’ll begin to see results in ... longer, and more easily. As you increase your fitness level, you also might find that you need ...

  6. Reaching for the Stars

    ERIC Educational Resources Information Center

    Terry, Dorothy Givens

    2012-01-01

    Dr. Mae Jemison is the world's first woman astronaut of color who continues to reach for the stars. Jemison was recently successful in leading a team that has secured a $500,000 federal grant to make interstellar space travel a reality. The Dorothy Jemison Foundation for Excellence (named after Jemison's mother) was selected in June by the Defense…

  7. Preparation of cross-linked magnetic chitosan-phenylthiourea resin for adsorption of Hg(II), Cd(II) and Zn(II) ions from aqueous solutions.

    PubMed

    Monier, M; Abdel-Latif, D A

    2012-03-30

    In this study, cross-linked magnetic chitosan-phenylthiourea (CSTU) resin were prepared and characterized by means of FTIR, (1)H NMR, SEM high-angle X-ray diffraction (XRD), magnetic properties and thermogravimetric analysis (TGA). The prepared resin were used to investigate the adsorption properties of Hg(II), Cd(II) and Zn(II) metal ions in an aqueous solution. The extent of adsorption was investigated as a function of pH and the metal ion removal reached maximum at pH 5.0. Also, the kinetic and thermodynamic parameters of the adsorption process were estimated. These data indicated that the adsorption process is exothermic and followed the pseudo-second-order kinetics. Equilibrium studies showed that the data of Hg(II), Cd(II) and Zn(II) adsorption followed the Langmuir model. The maximum adsorption capacities for Hg(II), Cd(II) and Zn(II) were estimated to be 135 ± 3, 120 ± 1 and 52 ± 1 mg/g, which demonstrated the high adsorption efficiency of CSTU toward the studied metal ions. PMID:22277339

  8. Isotherm study of reactive Blue 19 adsorption by an alum sludge

    NASA Astrophysics Data System (ADS)

    Khim, Ong Keat; Nor, Mohd Asri Md; Mohamad, Syuriya; Nasaruddin, Nas Aulia Ahmad; Jamari, Nor Laili-Azua; Yunus, Wan Md Zin Wan

    2015-05-01

    This study investigates the adsorption of Reactive Blue 19 using dewatered alum sludge. The dewatered alum sludge was a sludge produced from drinking water treatment plant. Batch adsorption experiments were performed to investigate the mechanism of the dye adsorption. The adsorption was rapid at its initial stage but the rate decreased as it approached equilibrium. The adsorption data were evaluated by Langmuir and Freundlich isotherm models but was best described by the Langmuir isotherm model as it gave the highest correlation.

  9. Cr-Doped ZnO Nanoparticles: Synthesis, Characterization, Adsorption Property, and Recyclability.

    PubMed

    Meng, Alan; Xing, Jing; Li, Zhenjiang; Li, Qingdang

    2015-12-16

    In this paper, a mild solvothermal method has been employed to successfully synthesize a series of Cr-doped ZnO nanoparticles (NPs) with different Cr(3+) contents, which is a kind of novel and high-efficiency absorbent for the removal of acid dye methyl orange (MO) from aqueous solution. The as-prepared products were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), Brunauer, Emmet, and Teller (BET), and Zeta potential measurements. In accordance with the adsorption capacity of the products, the obtained optimal Cr/Zn molar ratio is 6%. The adsorption process of MO on Cr-doped ZnO was investigated by kinetics, thermodynamics, and isotherm technologies, which, respectively, indicated that the adsorption was fast (adsorption reached equilibrium in 2 h) and followed a pseudo-second-order model, that the adsorption process was spontaneous and endothermic, and that it agreed well with the Langmuir isotherm with a maximum adsorption capacity of 310.56 mg g(-1). Moreover, a reasonable mechanism was proposed to elucidate the reasons for their adsorption behavior. In addition, a simple and low-cost chemical method was developed to separate and recycle ZnO and MO from the used adsorbent, effectively avoiding the secondary pollution. This work can not only describe efficient experimental approaches for obtaining novel adsorbents and recycling them but also offer valuable clues for the preparation and property study of other semiconductor adsorbents. PMID:26600320

  10. Pretoria Centre Reaches Out

    NASA Astrophysics Data System (ADS)

    Bosman, Olivier

    2014-08-01

    On 5 July 2014 six members of the Pretoria Centre of ASSA braved the light pollution of one of the shopping malls in Centurion to reach out to shoppers a la John Dobson and to show them the moon, Mars and Saturn. Although the centre hosts regular monthly public observing evenings, it was felt that we should take astronomy to the people rather than wait for the people to come to us.

  11. Tuning universality far from equilibrium

    PubMed Central

    Karl, Markus; Nowak, Boris; Gasenzer, Thomas

    2013-01-01

    Possible universal dynamics of a many-body system far from thermal equilibrium are explored. A focus is set on meta-stable non-thermal states exhibiting critical properties such as self-similarity and independence of the details of how the respective state has been reached. It is proposed that universal dynamics far from equilibrium can be tuned to exhibit a dynamical transition where these critical properties change qualitatively. This is demonstrated for the case of a superfluid two-component Bose gas exhibiting different types of long-lived but non-thermal critical order. Scaling exponents controlled by the ratio of experimentally tuneable coupling parameters offer themselves as natural smoking guns. The results shed light on the wealth of universal phenomena expected to exist in the far-from-equilibrium realm. PMID:23928853

  12. Adsorption of xenon and krypton on shales

    NASA Technical Reports Server (NTRS)

    Podosek, F. A.; Bernatowicz, T. J.; Kramer, F. E.

    1981-01-01

    A method that uses a mass spectrometer as a manometer is employed in the measurement of Xe and Kr adsorption parameters on shales and related samples, where gas partial pressures were lower than 10 to the -11th atm, corresponding adsorption coverages are only small fractions of a monolayer, and Henry's Law behavior is expected and observed. Results show heats of adsorption in the 2-7 kcal/mol range, and Henry constants at 0-25 C of 1 cu cm STP/g per atmosphere are extrapolated. Although the adsorption properties obtained are variable by sample, the range obtained suggests that shales may be capable of an equilibrium adsorption with modern air high enough to account for a significant fraction of the atmospheric inventory of Xe, and perhaps even of Kr. This effect will nevertheless not account for the factor-of-25 defficiency of atmospheric Xe, in comparison with the planetary gas patterns observed in meteorites.

  13. Removal of cadmium(II) ions from aqueous solution using Ni (15 wt.%)-doped α-Fe2O3 nanocrystals: equilibrium, thermodynamic, and kinetic studies.

    PubMed

    OuldM'hamed, Mohamed; Khezami, L; Alshammari, Abdulrahman G; Ould-Mame, S M; Ghiloufi, I; Lemine, O M

    2015-01-01

    The present publication investigates the performance of nanocrystalline Ni (15 wt.%)-doped α-Fe2O3 as an effective nanomaterial for the removal of Cd(II) ions from aqueous solutions. The nanocrystalline Ni-doped α-Fe2O3 powders were prepared by mechanical alloying, and characterized by X-ray diffraction and a vibrating sample magnetometer. Batch-mode experiments were realized to determine the adsorption equilibrium, kinetics, and thermodynamic parameters of toxic heavy metal ions by Ni (15 wt.%)-doped α-Fe2O3. The adsorption isotherms data were found to be in good agreement with the Langmuir model. The adsorption capacity of Cd(II) ion reached a maximum value of about 90.91 mg g(-1) at 328 K and pH 7. The adsorption process kinetics was found to comply with pseudo-second-order rate law. Thermodynamic parameters related to the adsorption reaction, free energy change, enthalpy change and entropy change, were evaluated. The found values of free energy and enthalpy revealed a spontaneous endothermic adsorption-process. Moreover, the positive entropy suggests an increase of randomness during the process of heavy metal removal at the adsorbent-solution interface. PMID:26247760

  14. Nickel(II) adsorption onto biomass based activated carbon obtained from sugarcane bagasse pith.

    PubMed

    Krishnan, K Anoop; Sreejalekshmi, K G; Baiju, R S

    2011-11-01

    Bioavailability of Nickel in the form of hydrated Nickel(II) attributes to its toxicological effects and hence its removal from aqueous solution is of great concern. Adsorption is used as an efficient technique for the removal of Nickel(II), hereafter Ni(II), from water and wastewaters. Activated carbon obtained from sugarcane bagasse pith (SBP-AC), a waste biomass collected from juice shops in Sarkara Devi Temple, Chirayinkeezhu, Trivandrum, India during annual festival, is used as adsorbent in the study. The process of adsorption is highly dependent on solution pH, and maximum removal occurs in the pH range of 4.0-8.0. Moreover, the amount of Ni(II) adsorbed onto SBP-AC increased with the time increase and reached equilibrium at 4h. Adsorption kinetic and equilibrium data were analyzed for determining the best fit kinetic and isotherm models. The overall study reveals the potential value of steam pyrolysed SBP-AC as a possible commercial adsorbent in wastewater treatment strategies. PMID:21924900

  15. Adsorption and desorption kinetics of (60)Co and (137)Cs in fresh water rivers.

    PubMed

    Fiengo Pérez, Fabricio; Sweeck, Lieve; Bauwens, Willy; Van Hees, May; Elskens, Marc

    2015-11-01

    Radionuclides released in water systems--as well as heavy metals and organic toxicants--sorb to both the suspended solid particles and the bed sediments. Sorption is usually represented mathematically by the distribution coefficient. This approach implies equilibrium between phases and instantaneous fixation (release) of the pollutant onto (from) the surface of the soil particle. However, empirical evidence suggests that for some radionuclides the fixation is not achieved instantaneously and that the reversibility of the process can be slow. Here the adsorption/desorption kinetics of (60)Co and (137)Cs in fresh water environments were simulated experimentally and later on modelled mathematically, while the influence of the most relevant factors affecting the sorption were taken into account. The experimental results suggest that for adsorption and the desorption more than 24 h are needed to reach equilibrium, moreover, It was observed that the desorption rate constants for (60)Co and (137)Cs lie within ranges which are of two to three orders of magnitude lower than the adsorption rate constants. PMID:26218323

  16. Influence of soil solution salinity on boron adsorption by soils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Boron adsorption on two arid-zone soils from the San Joaquin Valley of California was investigated as a function of equilibrium solution B concentration (0-250 mg L-1), solution pH (3-12), and electrical conductivity (EC = 0.3 or 7.8 dS m-1). Boron adsorption on both soils increased with increasing...

  17. Adsorption of chlorophenols on granular activated carbon

    SciTech Connect

    Yang, M.

    1993-12-31

    Studies were undertaken of the adsorption of chlorinated phenols from aqueous solution on granular activated carbon (Filtrasorb-400, 30 x 40 mesh). Single-component equilibrium adsorption data on the eight compounds in two concentration ranges at pH 7.0 fit the Langmuir equation better than the Freundlich equation. The adsorptive capacities at pH 7.0 increase from pentachlorophenol to trichlorophenols and are fairly constant from trichlorophenols to monochlorophenols. The adsorption process was found to be exothermic for pentachlorophenol and 2,4,6-trichlorophenol, and endothermic for 2,4-dichlorophenol and 4-chlorophenol. Equilibrium measurements were also conducted for 2,4,5-trichlorophenol, 2,4-dichlorophenol, and 4-chlorophenol over a wide pH range. A surface complexation model was proposed to describe the effect of pH on adsorption equilibria of chlorophenols on activated carbon. The simulations of the model are in excellent agreement with the experimental data. Batch kinetics studies were conducted of the adsorption of chlorinated phenols on granular activated carbon. The results show that the surface reaction model best describes both the short-term and long-term kinetics, while the external film diffusion model describes the short-term kinetics data very well and the linear-driving-force approximation improved its performance for the long-term kinetics. Multicomponent adsorption equilibria of chlorophenols on granular activated carbon was investigated in the micromolar equilibrium concentration range. The Langmuir competitive and Ideal Adsorbed Solution (IAS) models were tested for their performance on the three binary systems of pentachlorophenol/2,4,6-trichlorophenol, 2,4,6-trichlorophenol/2,4-dichlorophenol, and 2,4-dichlorophenol/4-chlorophenol, and the tertiary system of 2,4,6-trichlorophenol/2,4-dichlorophenol/4-chlorophenol, and found to fail to predict the two-component adsorption equilibria of the former two binary systems and the tertiary system.

  18. Morphodynamic equilibrium of alluvial estuaries

    NASA Astrophysics Data System (ADS)

    Tambroni, Nicoletta; Bolla Pittaluga, Michele; Canestrelli, Alberto; Lanzoni, Stefano; Seminara, Giovanni

    2014-05-01

    The evolution of the longitudinal bed profile of an estuary, with given plan-form configuration, subject to given tidal forcing at the mouth and prescribed values of water and sediment supply from the river is investigated numerically. Our main goal is to ascertain whether, starting from some initial condition, the bed evolution tends to reach a unique equilibrium configuration asymptotically in time. Also, we investigate the morphological response of an alluvial estuary to changes in the tidal range and hydrologic forcing (flow and sediment supply). Finally, the solution helps characterizing the transition between the fluvially dominated region and the tidally dominated region of the estuary. All these issues play an important role also in interpreting how the facies changes along the estuary, thus helping to make correct paleo-environmental and sequence-stratigraphic interpretations of sedimentary successions (Dalrymple and Choi, 2007). Results show that the model is able to describe a wide class of settings ranging from tidally dominated estuaries to fluvially dominated estuaries. In the latter case, the solution is found to compare satisfactory with the analytical asymptotic solution recently derived by Seminara et al. (2012), under the hypothesis of fairly 'small' tidal oscillations. Simulations indicate that the system always moves toward an equilibrium configuration in which the net sediment flux in a tidal cycle is constant throughout the estuary and equal to the constant sediment flux discharged from the river. For constant width, the bed equilibrium profile of the estuarine channel is characterized by two distinct regions: a steeper reach seaward, dominated by the tide, and a less steep upstream reach, dominated by the river and characterized by the undisturbed bed slope. Although the latter reach, at equilibrium, is not directly affected by the tidal wave, however starting from an initial uniform stream with the constant 'fluvial' slope, the final

  19. Local Nash Equilibrium in Social Networks

    PubMed Central

    Zhang, Yichao; Aziz-Alaoui, M. A.; Bertelle, Cyrille; Guan, Jihong

    2014-01-01

    Nash equilibrium is widely present in various social disputes. As of now, in structured static populations, such as social networks, regular, and random graphs, the discussions on Nash equilibrium are quite limited. In a relatively stable static gaming network, a rational individual has to comprehensively consider all his/her opponents' strategies before they adopt a unified strategy. In this scenario, a new strategy equilibrium emerges in the system. We define this equilibrium as a local Nash equilibrium. In this paper, we present an explicit definition of the local Nash equilibrium for the two-strategy games in structured populations. Based on the definition, we investigate the condition that a system reaches the evolutionary stable state when the individuals play the Prisoner's dilemma and snow-drift game. The local Nash equilibrium provides a way to judge whether a gaming structured population reaches the evolutionary stable state on one hand. On the other hand, it can be used to predict whether cooperators can survive in a system long before the system reaches its evolutionary stable state for the Prisoner's dilemma game. Our work therefore provides a theoretical framework for understanding the evolutionary stable state in the gaming populations with static structures. PMID:25169150

  20. Modification of carbon derived from Sargassum sp. by lanthanum for enhanced adsorption of fluoride.

    PubMed

    Yu, Yang; Wang, Chenghong; Guo, Xue; Paul Chen, J

    2015-03-01

    Excessive fluoride in water causes serious environmental issues and adverse impacts on human health. In this study, an innovative lanthanum-modified carbon (LMC) adsorbent rooted in Sargassum sp. was developed for fluoride removal. Excellent removal efficiency was observed over a wide pH range of 3-9. Almost 90% of fluoride adsorption occurred within the first 1h; the equilibrium was established within 4h. The maximum adsorption capacity of LMC could reach 94.34 mg/g at neutral pH, much higher than many commercial adsorbents. Although the presence of such competitive anions as SiO3(2-), SO4(2-), HCO3(-), PO4(3-) and AsO3(-) had certain interference on fluoride uptake, it was noticed that there was no significant impact in the presence of humic acid. Furthermore, according to the instrumental analysis, the fluoride removal was majorly controlled by outer-sphere complex adsorption, while electrostatic attraction and ion exchange mechanisms could also be observed in the fluoride adsorption process. The findings from this study suggest that our adsorbent may have a great potential in industrial applications. PMID:25498487

  1. A Porous Aromatic Framework Constructed from Benzene Rings Has a High Adsorption Capacity for Perfluorooctane Sulfonate

    PubMed Central

    Luo, Qin; Zhao, Changwei; Liu, Guixia; Ren, Hao

    2016-01-01

    A low-cost and easily constructed porous aromatic framework (PAF-45) was successfully prepared using the Scholl reaction. PAF-45 was, for the first time, used to remove perfluorooctane sulfonate (PFOS) from aqueous solution. Systematic experiments were performed to determine the adsorption capacity of PAF-45 for PFOS and to characterize the kinetics of the adsorption process. The adsorption of PFOS onto PAF-45 reached equilibrium in 30 min, and the adsorption capacity of PAF-45 for PFOS was excellent (5847 mg g−1 at pH 3). The amount of PFOS adsorbed by PAF-45 increased significantly as the cation (Na+, Mg2+, or Fe3+) concentration increased, which probably occurred because the cations enhanced the interactions between the negatively charged PFOS molecules and the positively charged PAF-45 surface. The cations Na+, Mg2+, and Fe3+ were found to form complexes with PFOS anions in solution. Density functional theory was used to identify the interactions between PFOS and Na+, Mg2+, and Fe3+. We expect that materials of the same type as PAF-45 could be useful adsorbents for removing organic pollutants from industrial wastewater and contaminated surface water. PMID:26843015

  2. [Heavy metals contents and Hg adsorption characteristics of mosses in virgin forest of Gongga Mountain].

    PubMed

    Liang, Peng; Yang, Yong-Kui; He, Lei; Wang, Ding-Yong

    2008-06-01

    Seven main moss species in the Hailuogou virgin forest of Gongga Mountain were sampled to determine their heavy metals (Hg, Cr, Cd, Ni, Pb, Cu, Mn, Zn and Fe) content, and two widely distributed species, Pleurozium schreberi (Brid.) Mitt. and Racomitrium laetum Besch., were selected to study their Hg adsorption characteristics. The results showed that the heavy metals contents in the mosses were lower than the background values in Europe and America, except that the Cd had a comparable value, which indicated that the atmosphere in study area was not polluted by heavy metals and good in quality. The Hg adsorption by P. schreberi and R. laetum was an initiative and rapid process, with the equilibrium reached in about two hours, and could be well fitted by Freundlich and Langmuir equations. Based on Langmuir equation, the maximum Hg adsorption capacities of P. schreberi and R. laetum were 15.24 and 8.19 mg x g(-1), respectively, suggesting that the two mosses had a good capacity of Hg adsorption, and could be used as the bio-monitors of atmospheric Hg pollution. PMID:18808007

  3. A Porous Aromatic Framework Constructed from Benzene Rings Has a High Adsorption Capacity for Perfluorooctane Sulfonate.

    PubMed

    Luo, Qin; Zhao, Changwei; Liu, Guixia; Ren, Hao

    2016-01-01

    A low-cost and easily constructed porous aromatic framework (PAF-45) was successfully prepared using the Scholl reaction. PAF-45 was, for the first time, used to remove perfluorooctane sulfonate (PFOS) from aqueous solution. Systematic experiments were performed to determine the adsorption capacity of PAF-45 for PFOS and to characterize the kinetics of the adsorption process. The adsorption of PFOS onto PAF-45 reached equilibrium in 30 min, and the adsorption capacity of PAF-45 for PFOS was excellent (5847 mg g(-1) at pH 3). The amount of PFOS adsorbed by PAF-45 increased significantly as the cation (Na(+), Mg(2+), or Fe(3+)) concentration increased, which probably occurred because the cations enhanced the interactions between the negatively charged PFOS molecules and the positively charged PAF-45 surface. The cations Na(+), Mg(2+), and Fe(3+) were found to form complexes with PFOS anions in solution. Density functional theory was used to identify the interactions between PFOS and Na(+), Mg(2+), and Fe(3+). We expect that materials of the same type as PAF-45 could be useful adsorbents for removing organic pollutants from industrial wastewater and contaminated surface water. PMID:26843015

  4. Efficient and selective adsorption of multi-metal ions using sulfonated cellulose as adsorbent.

    PubMed

    Dong, Cuihua; Zhang, Fulong; Pang, Zhiqiang; Yang, Guihua

    2016-10-20

    Contamination of heavy metal in wastewater has caused great concerns on human life and health. Developing an efficient material to eliminate the heavy metal ions has been a popular topic in recent years. In this work, sulfonated cellulose (SC) was explored as efficient adsorbent for metal ions in solution. Thermo gravimetric analyzer (TGA), X-ray diffraction (XRD) and Fourier-transform infrared spectrometer (FTIR) first analyzed the characterizations of SC. Subsequently, effects of solution pH, adsorbent loading, temperature and initial metal ion concentration on adsorption performance were investigated. The results showed that sulfonated modification of cellulose could decrease the crystallinity and thermostability of cellulose. Due to its excellent performance of adsorption to metal ions, SC could reach adsorption equilibrium status within as short as 2min. In multi-component solution, SC can orderly removes Fe(3+), Pb(2+) and Cu(2+) with excellent selectivity and high efficiency. In addition, SC is a kind of green and renewable adsorbent because it can be easily regenerated by treatment with acid or chelating liquors. The mechanism study shows that the sulfonic group play a major role in the adsorption process. PMID:27474562

  5. Nitrate adsorption from aqueous solution using granular chitosan-Fe3+ complex

    NASA Astrophysics Data System (ADS)

    Hu, Qili; Chen, Nan; Feng, Chuanping; Hu, WeiWu

    2015-08-01

    In the present study, In order to efficiently remove nitrate, granular chitosan-Fe3+ complex with high chemical stability and good environmental adaptation was synthesized through precipitation method and characterized using SEM, XRD, BET and FTIR. The nitrate adsorption performance was evaluated by batch experiments. The results indicated that granular chitosan-Fe3+ complex was an amorphous and mesoporous material. The BET specific surface area and average pore size were 8.98 m2 g-1 and 56.94 Å, respectively. The point of zero charge was obtained at pH 5. The maximum adsorption capacity reached 8.35 mg NO3--N g-1 based on Langmuir-Freundlich model. Moreover, no significant change in the nitrate removal efficiency was observed in the pH range of 3.0-10.0. The adverse influence of sulphate on nitrate removal was the most significant, followed by bicarbonate and fluoride, whereas chloride had slightly adverse effect. Adsorption process followed the pseudo-second-order kinetic model, and the experimental equilibrium data were fitted well with the Langmuir-Freundlich and D-R isotherm models. Thermodynamic parameters revealed that nitrate adsorption was a spontaneous and exothermic process. Granular chitosan-Fe3+ complex could be effectively regenerated by NaCl solution.

  6. Dye adsorption and bactericidal properties of TiO2/chitosan coating layer.

    PubMed

    Kamal, Tahseen; Anwar, Yasir; Khan, Sher Bahadar; Chani, Muhammad Tariq Saeed; Asiri, Abdullah M

    2016-09-01

    A new kind of titanium oxide dispersed in chitosan (TiO2/CS) nanocomposite adsorbent was prepared and adhered to high surface area substrate, cellulose microfibers mat (CMM). CS-CMM and TiO2/CS-CMM were used for the thymol violet (TV) dye removal from wastewater. Characterization of materials was carried out by X-ray diffraction, scanning electron microscope and energy dispersive X-ray spectroscopy. The adsorption properties of both the CS-CMM and TiO2/CS-CMM were investigated as a function of adsorbent dosage, solution pH, and contact time. It was revealed that the composites pretreated in the solution with higher pH value exhibited larger adsorption capacities. Kinetic studies showed that the composites could adsorb TV dye rapidly and reached the equilibrium in 90min. The adsorption process followed pseudo-second order kinetics and involved particle diffusion mechanism. The calculated maximum adsorption capacities of CS-CMM and TiO2/CS-CMM were 84.32 and 97.51mgg(-1), respectively. Compare to CS, the TiO2/CS nanocomposite coated CMM showed higher antibacterial characteristics as tested against Escherichia coli. PMID:27185126

  7. A Porous Aromatic Framework Constructed from Benzene Rings Has a High Adsorption Capacity for Perfluorooctane Sulfonate

    NASA Astrophysics Data System (ADS)

    Luo, Qin; Zhao, Changwei; Liu, Guixia; Ren, Hao

    2016-02-01

    A low-cost and easily constructed porous aromatic framework (PAF-45) was successfully prepared using the Scholl reaction. PAF-45 was, for the first time, used to remove perfluorooctane sulfonate (PFOS) from aqueous solution. Systematic experiments were performed to determine the adsorption capacity of PAF-45 for PFOS and to characterize the kinetics of the adsorption process. The adsorption of PFOS onto PAF-45 reached equilibrium in 30 min, and the adsorption capacity of PAF-45 for PFOS was excellent (5847 mg g-1 at pH 3). The amount of PFOS adsorbed by PAF-45 increased significantly as the cation (Na+, Mg2+, or Fe3+) concentration increased, which probably occurred because the cations enhanced the interactions between the negatively charged PFOS molecules and the positively charged PAF-45 surface. The cations Na+, Mg2+, and Fe3+ were found to form complexes with PFOS anions in solution. Density functional theory was used to identify the interactions between PFOS and Na+, Mg2+, and Fe3+. We expect that materials of the same type as PAF-45 could be useful adsorbents for removing organic pollutants from industrial wastewater and contaminated surface water.

  8. [Adsorption Behaviors of Lead on Multi-Walled Carbon Nanotube-Hydroxyapatite Composites].

    PubMed

    Zhang, Jin-li; Li, Yu

    2015-07-01

    Multi-walled carbon nanotube-hydroxyapatite composites (MWCNT-HAP) were employed as the sorbent to study the sorption characteristic of Pb (II) using batch experiments. Effects of dosage of adsorbent, pH, ionic strength, contact time, initial concentration of lead and temperature were investigated. The results indicated that the removal of lead to MWCNT-HAP composites was strongly dependent on dosage of adsorbent, pH, temperature, and independent of ionic strength. The maximum adsorption capacity of lead was about 716. 13 mg.g-1 at 20°C, with a solid/liquid ratio of 0.08 g.L-1, pH0 = 5.5 and an initial concentration of 100 mg.L-1. The adsorption of Pb(II) on MWCNT-HAP composites was a fast process and could reach the equilibrium within 60 minutes. Ninety percent of the maximum adsorption capacity could be reached in 30 minutes. The kinetic data were fitted to pseudo-second-order kinetic model reasonably well. The kinetic sorption of Pb(II) on MWCNT-HAP was well described by pseudo-second-order kinetic model. The negative free energy calculated from the temperature dependent sorption isotherms suggested that the sorption of Pb(II) on MWCNT-HAP composites was a spontaneous process, and high temperature favored the adsorption process. The higher correlation coefficient values (R2 = 0. 999 8 - 1. 000 0) of Langmuir isotherm model at different temperatures suggested that Langmuir model could be used to simulate the sorption of Pb(II) on MWCNT-HAP. The adsorption mechanism mainly involves surface complexation between the lead ions and the surface oxygen-containing functional groups of the MWCNT-HAP, dissolution of HAP and precipitation of pyromorphite [Pb10 (PO4)6 (OH) 2], ion exchange reaction between Pb2+ and Ca2+ of hydroxyapatite. PMID:26489325

  9. Adsorption of Cd(II) and Cu(II) from aqueous solution by carbonate hydroxylapatite derived from eggshell waste.

    PubMed

    Zheng, Wei; Li, Xiao-ming; Yang, Qi; Zeng, Guang-ming; Shen, Xiang-xin; Zhang, Ying; Liu, Jing-jin

    2007-08-17

    Carbonate hydroxylapatite (CHAP) synthesized by using eggshell waste as raw material has been investigated as metal adsorption for Cd(II) and Cu(II) from aqueous solutions. The effect of various parameters on adsorption process such as contact time, solution pH, amount of CHAP and initial concentration of metal ions was studied at room temperature to optimize the conditions for maximum adsorption. The results showed that the removal efficiency of Cd(II) and Cu(II) by CHAP could reach 94 and 93.17%, respectively, when the initial Cd(II) concentration 80 mg/L and Cu(II) 60 mg/L and the liquid/solid ratio was 2.5 g/L. The equilibrium sorption data for single metal systems at room temperature could be described by the Langmuir and Freundlich isotherm models. The highest value of Langmuir maximum uptake, (b), was found for cadmium (111.1mg/g) and copper (142.86 mg/g). Similar Freundlich empirical constants, K, were obtained for cadmium (2.224) and copper (7.925). Ion exchange and surface adsorption might be involved in the adsorption process of cadmium and copper. Desorption experiments showed that CaCl2, NaCl, acetic acid and ultrasonic were not efficient enough to desorb substantial amount of metal ions from the CHAP. The results obtained show that CHAP has a high affinity to cadmium and copper. PMID:17368932

  10. Isotherms for Water Adsorption on Molecular Sieve 3A: Influence of Cation Composition

    DOE PAGESBeta

    Lin, Ronghong; Ladshaw, Austin; Nan, Yue; Liu, Jiuxu; Yiacoumi, Sotira; Tsouris, Costas; DePaoli, David W.; Tavlarides, Lawrence L.

    2015-06-16

    This study is part of our continuing efforts to address engineering issues related to the removal of tritiated water from off-gases produced in used nuclear fuel reprocessing facilities. In the current study, adsorption equilibrium of water on molecular sieve 3A beads was investigated. Adsorption isotherms for water on the UOP molecular sieve 3A were measured by a continuous-flow adsorption system at 298, 313, 333, and 353 K. Experimental data collected were analyzed by the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm model. The K+/Na+ molar ratio of this particular type of molecular sieve 3A was ~4:6. Our results showed that themore » GSTA isotherm model worked very well to describe the equilibrium behavior of water adsorption on molecular sieve 3A. The optimum number of parameters for the current experimental data was determined to be a set of four equilibrium parameters. This result suggests that the adsorbent crystals contain four energetically distinct adsorption sites. In addition, it was found that water adsorption on molecular sieve 3A follows a three-stage adsorption process. This three-stage adsorption process confirmed different water adsorption sites in molecular sieve crystals. In addition, the second adsorption stage is significantly affected by the K+/Na+ molar ratio. In this stage, the equilibrium adsorption capacity at a given water vapor pressure increases as the K+/Na+ molar ratio increases.« less

  11. Isotherms for Water Adsorption on Molecular Sieve 3A: Influence of Cation Composition

    SciTech Connect

    Lin, Ronghong; Ladshaw, Austin; Nan, Yue; Liu, Jiuxu; Yiacoumi, Sotira; Tsouris, Costas; DePaoli, David W.; Tavlarides, Lawrence L.

    2015-06-16

    This study is part of our continuing efforts to address engineering issues related to the removal of tritiated water from off-gases produced in used nuclear fuel reprocessing facilities. In the current study, adsorption equilibrium of water on molecular sieve 3A beads was investigated. Adsorption isotherms for water on the UOP molecular sieve 3A were measured by a continuous-flow adsorption system at 298, 313, 333, and 353 K. Experimental data collected were analyzed by the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm model. The K+/Na+ molar ratio of this particular type of molecular sieve 3A was ~4:6. Our results showed that the GSTA isotherm model worked very well to describe the equilibrium behavior of water adsorption on molecular sieve 3A. The optimum number of parameters for the current experimental data was determined to be a set of four equilibrium parameters. This result suggests that the adsorbent crystals contain four energetically distinct adsorption sites. In addition, it was found that water adsorption on molecular sieve 3A follows a three-stage adsorption process. This three-stage adsorption process confirmed different water adsorption sites in molecular sieve crystals. In addition, the second adsorption stage is significantly affected by the K+/Na+ molar ratio. In this stage, the equilibrium adsorption capacity at a given water vapor pressure increases as the K+/Na+ molar ratio increases.

  12. Europe reaches the Moon

    NASA Astrophysics Data System (ADS)

    2004-11-01

    A complex package of tests on new technologies was successfully performed during the cruise to the Moon, while the spacecraft was getting ready for the scientific investigations which will come next. These technologies pave the way for future planetary missions. SMART-1 reached its closest point to the lunar surface so far - its first ‘perilune’ - at an altitude of about 5000 kilometres at 18:48 Central European Time (CET) on 15 November. Just hours before that, at 06:24 CET, SMART-1’s solar-electric propulsion system (or ‘ion engine’) was started up and is now being fired for the delicate manoeuvre that will stabilise the spacecraft in lunar orbit. During this crucial phase, the engine will run almost continuously for the next four days, and then for a series of shorter burns, allowing SMART-1 to reach its final operational orbit by making ever-decreasing loops around the Moon. By about mid-January, SMART-1 will be orbiting the Moon at altitudes between 300 kilometres (over the lunar south pole) and 3000 kilometres (over the lunar north pole), beginning its scientific observations. The main purpose of the first part of the SMART-1 mission, concluding with the arrival at the Moon, was to demonstrate new spacecraft technologies. In particular, the solar-electric propulsion system was tested over a long spiralling trip to the Moon of more than 84 million kilometres. This is a distance comparable to an interplanetary cruise. For the first time ever, gravity-assist manoeuvres, which use the gravitational pull of the approaching Moon, were performed by an electrically-propelled spacecraft. The success of this test is important to the prospects for future interplanetary missions using ion engines. SMART-1 has demonstrated new techniques for eventually achieving autonomous spacecraft navigation. The OBAN experiment tested navigation software on ground computers to determine the exact position and velocity of the spacecraft using images of celestial objects taken

  13. Reaching Beyond The Stars

    NASA Astrophysics Data System (ADS)

    Baker, Mariah; Rosenthal, L.; Gaughan, A.; Hopkins, E.

    2014-01-01

    Strawbridge Observatory at Haverford College is home to a undergraduate-led public observing program. Our program holds ~once monthly public events throughout the academic year that take advantage of eyepiece observing on our 16-inch and 12-inch telescopes as well as of the classroom, library, and projection system. These resources allow us to organize a variety of astronomy related activities that are engaging for individuals of all ages: accessible student talks, current film screenings and even arts and crafts for the families who attend with young children. These events aim to spark curiosity in others about scientific discovery and about the remarkable nature of the world in which we live. In addition to exciting local families about astronomy, this program has excited Haverford students from a range of disciplines about both science and education. Being entirely student led means that we are able to take the initiative in planning, coordinating and running all events, fostering an atmosphere of collaboration, experimentation and commitment amongst our volunteers. Additionally, this program is one of the few at Haverford that regularly reaches beyond the campus walls to promote and build relationships with the outside community. In light of this, our program presents a distinctive and enlightening opportunity for student volunteers: we get to use our scientific backgrounds to educate a general audience, while also learning from them about how to communicate and inspire in others the excitement we feel about the subject of astronomy. The work on this project has been supported by NSF AST-1151462.

  14. Hydrothermal synthesis of silico-manganese nanohybrid for Cu(II) adsorption from aqueous solution

    NASA Astrophysics Data System (ADS)

    Zhu, Qiufeng; Wang, Liting; An, Zehuan; Ye, Hong; Feng, Xudong

    2016-05-01

    A novel silico-manganese nanohybrid adsorbent (SMNA) was synthesized by a facile hydrothermal method, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), nitrogen adsorption-desorption, Fourier transform infrared spectroscopy (FT-IR) and zeta potential measurement. The adsorption of Cu(II) ions from aqueous solution on the SMNA was investigated with variations in contact time, pH and initial Cu(II) concentration. The results showed that hydrothermal method would generate nanowire/nanorod incomplete crystallite (δ-MnO2) adsorbent. The adsorption of Cu(II) onto SMNA increased sharply within 25 min and reached equilibrium gradually. The maximum adsorption capacities of SMNA for Cu(II) were ∼40-88 mg g-1, which was lower than δ-MnO2 (92.42 mg g-1) but had a lower pH dependency. As compared with δ-MnO2, higher adsorption capacities of SMNA (7.5-15 wt% of silica doping amount) for Cu(II) could be observed when pH of the aqueous solution was low (<4). The pseudo-second-order model was the best choice to describe the adsorption behavior of Cu(II) onto SMNA, suggesting that the removal of Cu(II) by the as-prepared adsorbents was dominated by migration of Cu(II). The possibility of Cu(II) recovery was also investigated and it revealed that SMNA was a promising recyclable adsorbent for removal of heavy metal ions in water and wastewater treatment.

  15. Impact of carbon nanotube morphology on phenanthrene adsorption.

    PubMed

    Apul, Onur Guven; Shao, Ting; Zhang, Shujuan; Karanfil, Tanju

    2012-01-01

    The present study examined the roles of the specific surface area (SSA), diameter, and length of carbon nanotubes (CNT) on the adsorption of phenanthrene (PNT) by analyzing the adsorption isotherms obtained with several single-walled carbon nanotubes (SWNT) and multiwalled carbon nanotubes (MWNT). At low equilibrium concentrations (e.g., 1 ppb), MWNTs with larger outer diameters exhibited higher PNT adsorption capacity on an SSA basis than those with smaller diameters. With increasing equilibrium concentration, adsorption on an SSA basis became independent of MWNT diameter, and the total surface area controlled maximum adsorption capacity. A similar analysis for the adsorption of naphthalene, a planar molecule with one less benzene ring but 20 times higher solubility than PNT, showed no correlation with respect to MWNT outer diameter. The results indicated that the surface curvature of MWNT was more important on the adsorption of PNT than on the adsorption of naphthalene. Specific surface area normalized isotherms did not show a correlation between PNT adsorption and lengths of SWNTs and MWNTs. Characterization results indicated that the morphology of CNTs plays an important role on the SSA and pore volume. Data from the manufacturer may not always represent the characteristics of CNTs in a particular batch. Therefore, accurate characterization of CNTs is critical to systematically examine the behavior of CNTs, such as adsorption and transport, in environmental systems. PMID:22002628

  16. Characterization of immunoglobulin adsorption on dextran-grafted hydrophobic charge-induction resins: Cross-effects of ligand density and pH/salt concentration.

    PubMed

    Liu, Tao; Lin, Dong-Qiang; Zhang, Qi-Lei; Yao, Shan-Jing

    2015-05-29

    Hydrophobic charge-induction chromatography (HCIC) is a promising technology for antibody purification. New HCIC resins MMI-B-XL with dextran-grafted agarose gel as the matrix and 2-mercapto-1-methyl-imidazole (MMI) as the functional ligand were prepared with different ligand densities. The adsorption behaviors (static adsorption equilibrium and adsorption kinetics) of human immunoglobulin G (hIgG) on series of MMI-B-XL resins at varying pHs and salt concentrations were investigated. The cross-effects of solid phase property (ligand density) and liquid phase conditions (pH and salt concentration) were focused. The results showed that the new resins had typical pH-dependent and salt-tolerant characteristics for hIgG adsorption, but differences were found for the resins with different ligand densities. For MMI-B-XL resins with higher ligand density, an obvious higher saturated adsorption capacity (Qm) and effective pore diffusivity (De) could be obtained, which were less affected at pH 7.0∼8.9 but dropped drastically at pH 5.0. Salt addition had less influence on protein adsorption onto MMI-B-XL with higher ligand density. Qm and De both reached minimum values at 0.2mol/L NaCl for all MMI-B-XL resins tested. The results of dynamic binding in the column demonstrated that MMI-B-XL with higher ligand density had better performance for hIgG adsorption, especially under high linear velocities. The mechanism of the cross-effects of ligand density and pH/salt concentration on IgG adsorption was discussed, which provides new insights into protein adsorption and mass transport for dextran-grafted HCIC resins. PMID:25892639

  17. Adsorption and excess fission xenon

    NASA Technical Reports Server (NTRS)

    Podosek, F. A.; Bernatowicz, T. J.; Kramer, F. E.

    1982-01-01

    The adsorption of Xe and Kr on lunar soil 10084 was measured by a method that employs only very low fractions of monolayer coverage. Results are presented as parameters for calculation of the Henry constant for adsorption as a function of temperature. The adsorption potentials are about 3 kcal/mole for Kr and 5 kcal/mole for Xe; heating the sample in vacuum increased the Xe potential to nearly 7 kcal/mole. Henry constants at the characteristic lunar temperature are about 0.3 cu cm STP/g-atm. These data were applied to consider whether adsorption is important in producing the excess fission Xe effect characteristic of highland breccias. Sorption equilibrium with a transient lunar atmosphere vented fission Xe produces concentrations seven orders of magnitude lower than observed concentrations. Higher concentrations result because of the resistance of the regolith to upward diffusion of Xe. A diffusion coefficient of 0.26 sq cm/sec is estimated for this process.

  18. Equilibrium Potentials of Membrane Electrodes

    PubMed Central

    Wang, Jui H.; Copeland, Eva

    1973-01-01

    A simple thermodynamic theory of the equilibrium potentials of membrane electrodes is formulated and applied to the glass electrode for measurement of pH. The new formulation assumes the selective adsorption or binding of specific ions on the surface of the membrane which may or may not be permeable to the ion, and includes the conventional derivation based on reversible ion transport across membranes as a special case. To test the theory, a platinum wire was coated with a mixture of stearic acid and methyl-tri-n-octyl-ammonium stearate. When this coated electrode was immersed in aqueous phosphate solution, its potential was found to be a linear function of pH from pH 2 to 12 with a slope equal to the theoretical value of 59.0 mV per pH unit at 24°. PMID:4516194

  19. Application of activated carbon derived from scrap tires for adsorption of Rhodamine B.

    PubMed

    Li, Li; Liu, Shuangxi; Zhu, Tan

    2010-01-01

    Activated carbon derived from solid hazardous waste scrap tires was evaluated as a potential adsorbent for cationic dye removal. The adsorption process with respect to operating parameters was investigated to evaluate the adsorption characteristics of the activated pyrolytic tire char (APTC) for Rhodamine B (RhB). Systematic research including equilibrium, kinetics and thermodynamic studies was performed. The results showed that APTC was a potential adsorbent for RhB with a higher adsorption capacity than most adsorbents. Solution pH and temperature exert significant influence while ionic strength showed little effect on the adsorption process. The adsorption equilibrium data obey Langmuir isotherm and the kinetic data were well described by the pseudo second-order kinetic model. The adsorption process followed intra-particle diffusion model with more than one process affecting the adsorption process. Thermodynamic study confirmed that the adsorption was a physisorption process with spontaneous, endothermic and random characteristics. PMID:21179969

  20. Solvothermal synthesis of MnFe2O4-graphene composite-Investigation of its adsorption and antimicrobial properties

    NASA Astrophysics Data System (ADS)

    Chella, Santhosh; Kollu, Pratap; Komarala, Eswara Vara P. R.; Doshi, Sejal; Saranya, Murugan; Felix, Sathiyanathan; Ramachandran, Rajendran; Saravanan, Padmanapan; Koneru, Vijaya Lakshmi; Venugopal, Velmurugan; Jeong, Soon Kwan; Nirmala Grace, Andrews

    2015-02-01

    Graphene manganese ferrite (MnFe2O4-G) composite was prepared by a solvothermal process. The as-prepared graphene manganese ferrite composite was tested for the adsorption of lead (Pb(II)) and cadmium (Cd(II)) ions by analytical methods under diverse experimental parameters. With respect to contact time measurements, the adsorption of Pb and Cd ions increased and reached equilibrium within 120 and 180 min at 37 °C with a maximum adsorption at pH 5 and 7 respectively. The Langmuir model correlates to the experimental data showing an adsorption capacity of 100 for Pb(II) and 76.90 mg g-1 for Cd(II) ions. Thermodynamic studies revealed that the adsorption of Pb and Cd ions onto MnFe2O4-G was spontaneous, exothermic and feasible in the range of 27-47 °C. Cytotoxicity behavior of graphene against bacterial cell membrane is well known. To better understand its antimicrobial mechanism, the antibacterial activity of graphene and MnFe2O4-G nanocomposite was compared. Under similar concentration and incubation conditions, nanocomposite MnFe2O4-G dispersion showed the highest antibacterial activity of 82%, as compared to graphene showing 37% cell loss. Results showed that the prepared composite possess good adsorption efficiency and thus could be considered as an excellent material for removal of toxic heavy metal ions as explained by adsorption isotherm. Hence MnFe2O4-G can be used as an adsorbent as well as an antimicrobial agent.

  1. Adsorption characteristics of nano-TiO2 onto zebrafish embryos and its impacts on egg hatching.

    PubMed

    Shih, Yu-Jen; Su, Chia-Chi; Chen, Chiu-Wen; Dong, Cheng-Di; Liu, Wen-Sheng; Huang, C P

    2016-07-01

    The characteristics of nanoparticles (NPs) uptake may fundamentally alter physicochemical effects of engineered NPs on aquatic organisms, thereby yielding different ecotoxicology assessment results. The adsorption behavior of nano-TiO2 (P-25) on zebrafish embryos in Holtfreter's medium (pH 7.2, I ∼ 7.2 × 10(-2) M) and the presence of sodium alginate (100 mg/L) as dispersant was investigated. Zebrafish embryos (total 100) were exposed to nano-TiO2 at different concentrations (e.g., 0, 10, 20, 60, 120 mg/L) in batch-mode assay. The adsorption capacity of nano-TiO2 on fish eggs was determined by measuring the Ti concentration on the egg surface using ICP-OES analysis. Results showed that the adsorption capacity increased rapidly in the first hour, and then declined to reach equilibrium in 8 h. The adsorption characteristics was visualized as a three-step process of rapid initial layer formation, followed by break-up of aggregates and finally rearrangement of floc structures; the maximum adsorption capacity was the sum of an inner rigid layers of aggregates of 0.81-0.84 μg-TiO2/#-egg and an outer softly flocculated layers of 1.01 μg-TiO2/#-egg. The Gibbs free energy was 543.29-551.26 and 100.75 kJ/mol, respectively, for the inner-layer and the outer-layer aggregates. Adsorption capacity at 0.5-1.0 μg-TiO2/#-egg promoted egg hatching; but hatching was inhibited at higher adsorption capacity. Results clearly showed that the configuration of TiO2 aggregates could impact the hatching efficiency of zebrafish embryos. PMID:27043376

  2. Zinc isotope fractionation during adsorption on calcite

    NASA Astrophysics Data System (ADS)

    Dong, S.; Wasylenki, L. E.

    2013-12-01

    Zinc is an important element as a nutrient in the marine biosphere. However, our understanding of its biogeochemical cycling in the oceans is relatively limited. The Zn stable isotope system holds the promise of providing novel insights, since published Zn isotopic values for various natural samples reveal significant fractionations in the marine environment. Surface seawater, basalts, shales, deep-sea clay sediments, sediment trap material, bulk plankton and zooplankton samples, and eolian dust fall within a tight range (δ66/64Zn from -0.1 to 0.5‰), but modern ferromanganese crusts (δ66/64Zn from 0.5 to 1.2‰), as well as carbonates (δ66/64Zn from 0.3 to 1.4‰), are notably enriched in heavy Zn isotopes [1-4]. In this study we seek to constrain the mechanism by which carbonates are enriched in heavier isotopes. In particular, we have conducted experiments to quantify isotope fractionation during adsorption of Zn onto the surfaces of calcite crystals that are in equilibrium with solution. The adsorption experiments were carried out in a series of small-volume batch reactions in a clean laboratory environment, using high-purity reagents and calcite seed crystals. The calcite was equilibrated with the solution prior to addition of Zn at atmospheric CO2 pressure (i.e., in air) for 5 days until a stable pH of 8.3 was reached. Later, a small aliquot of dissolved ZnCl2 was added such that the solution remained undersaturated with respect to hydrozincite. Experimental duration varied among the replicates from 6 to 144 hours, and then all solids and solutions were separated by filtration, purified by ion exchange chromatography, and analyzed by MC-ICP-MS. Zn adsorbed on calcite is isotopically heavier than in the co-existing solutions, with Δ68/66Zncalcite-solution of approximately 0.3‰. The variation of Δ68/66Zncalcite-solution beyond 24 hours is insignificant, so we infer that isotopic equilibrium is reached by this time. Previous work strongly suggests that a

  3. Reaching for the Unreachable: Reorganization of Reaching with Walking

    PubMed Central

    Grzyb, Beata J.; Smith, Linda B.; del Pobil, Angel P.

    2015-01-01

    Previous research suggests that reaching and walking behaviors may be linked developmentally as reaching changes at the onset of walking. Here we report new evidence on an apparent loss of the distinction between the reachable and nonreachable distances as children start walking. The experiment compared nonwalkers, walkers with help, and independent walkers in a reaching task to targets at varying distances. Reaching attempts, contact, leaning, and communication behaviors were recorded. Most of the children reached for the unreachable objects the first time it was presented. Nonwalkers, however, reached less on the subsequent trials showing clear adjustment of their reaching decisions with the failures. On the contrary, walkers consistently attempted reaches to targets at unreachable distances. We suggest that these reaching errors may result from inappropriate integration of reaching and locomotor actions, attention control and near/far visual space. We propose a reward-mediated model implemented on a NAO humanoid robot that replicates the main results from our study showing an increase in reaching attempts to nonreachable distances after the onset of walking. PMID:26110046

  4. THE EQUILIBRIUM FLUORIDE CAPACITY OF ACTIVATED ALUMINA. DETERMINATION OF THE EFFECTS OF PH AND COMPETING IONS

    EPA Science Inventory

    This report describes research on the determination of the equilibrium fluoride adsorption capacity of small columns of acid pretreated activated alumina (Alcoa F-1 grade). The experimental observations verified the expectation that fluoride is very favorably adsorbed in preferen...

  5. Adsorption of radon and water vapor on commercial activated carbons

    SciTech Connect

    Hassan, N.M.; Ghosh, T.K.; Hines, A.L.; Loyalka, S.K.

    1995-02-01

    Equilibrium adsorption isotherms are reported for radon and water vapor on two commercial activated carbons: coconut shell Type PCB and hardwood Type BD. The isotherms of the water vapor were measured gravimetrically at 298 K. The isotherms of radon from dry nitrogen were obtained at 293, 298, and 308 K while the data for the mixture of radon and water vapor were measured at 298 K. The concentrations of radon in the gas and solid phases were measured simultaneously, once the adsorption equilibrium and the radioactive equilibrium between the radon and its daughter products were established. The shape of the isotherms was of Type III for the radon and Type V for the water vapor, according to Brunauer`s classification. The adsorption mechanism was similar for both the radon and the water vapor, being physical adsorption on the macropore surface area in the low pressure region and micropore filling near saturation pressure. The uptake capacity of radon decreased both with increasing temperature and relative humidity. The heat of adsorption data indicated that the PCB- and the BD-activated carbons provided a heterogeneous surface for radon adsorption. The equilibrium data for radon were correlated with a modified Freundlich equation.

  6. [Ion specificity during ion exchange equilibrium in natural clinoptilolite].

    PubMed

    He, Yun-Hua; Li, Hang; Liu, Xin-Min; Xiong, Hai-Ling

    2015-03-01

    Zeolites have been widely applied in soil improvement and environment protection. The study on ion specificity during ion exchange equilibrium is of important significance for better use of zeolites. The maximum adsorption capacities of alkali ions during ion exchange equilibrium in the clinoptilolite showed obvious specificity. For alkali metal ions with equivalent valence, the differences in adsorption capacity increased with the decrease of ionic concentration. These results cannot be well explained by the classical theories including coulomb force, ionic size, hydration, dispersion force, classic induction force and surface complexation. We found that the coupling of polarization effects resulted from the quantum fluctuation of diverse alkali metal ions and electric field near the zeolite surface should be the primary reason for specific ion effect during ion exchange in zeolite. The result of this coupling effect was that the difference in the ion dipole moment increased with the increase of surface potential, which further expanded the difference in the adsorption ability between zeolite surface and ions, resulting in different ion exchange adsorption ability at the solid/liquid interface. Due to the high surface charge density of zeolite, ionic size also played an important role in the distribution of ions in the double diffuse layer, which led to an interesting result that distinct differences in exchange adsorption ability of various alkali metal ions were only detected at high surface potential (the absolute value was greater than 0.2 V), which was different from the ion exchange equilibrium result on the surface with low charge density. PMID:25929073

  7. Efficient adsorption of phenanthrene by simply synthesized hydrophobic MCM-41 molecular sieves

    NASA Astrophysics Data System (ADS)

    Hu, Yun; He, Yinyun; Wang, Xiaowen; Wei, Chaohai

    2014-08-01

    Hydrophobic molecular sieve MCM-41 including surfactant template was synthesized by a simple method. The adsorption properties of this material toward phenanthrene were studied. The effects of adsorbent dose and pH value on the adsorption process as well as the adsorption mechanism and reuse performance were investigated. The template-containing MCM-41 showed a significant adsorption for phenanthrene, due to its hydrophobicity created by the surfactant template in MCM-41. The solution pH had little effect on the adsorption capacity. The adsorption kinetic could be fitted well with pseudo-second-order kinetic model. The adsorption equilibrium was fitted well by the linear model, and the adsorption process followed the liquid/solid phase distribution mechanism. The thermodynamic results indicated that the adsorption was a spontaneous and exothermic process.

  8. Adsorption of arsenate from aqueous solution by rice husk-based adsorbent

    NASA Astrophysics Data System (ADS)

    Khan, Taimur; Chaudhuri, Malay

    2013-06-01

    Rice husk-based adsorbent (RHBA) was prepared by burning rice husk in a muffle furnace at 400°C for 4 h and adsorption of arsenate by the RHBA from aqueous solution was examined. Batch adsorption test showed that extent of arsenate adsorption depended on contact time and pH. Equilibrium adsorption was attained in 60 min, with maximum adsorption occurring at pH 7. Equilibrium adsorption data were well described by the Freundlich isotherm model. Freundlich constants Kf and 1/n were 3.62 and 2, respectively. The RHBA is effective in the adsorption of arsenate from water and is a potentially suitable filter medium for removing arsenate from groundwater at wells or in households.

  9. Understanding the Adsorption of PFOA on MIL-101(Cr)-Based Anionic-Exchange Metal-Organic Frameworks: Comparing DFT Calculations with Aqueous Sorption Experiments.

    PubMed

    Liu, Kai; Zhang, Siyu; Hu, Xiyue; Zhang, Kunyang; Roy, Ajay; Yu, Gang

    2015-07-21

    To examine the effects of different functionalization methods on adsorption behavior, anionic-exchange MIL-101(Cr) metal-organic frameworks (MOFs) were synthesized using preassembled modification (PAM) and postsynthetic modification (PSM) methods. Perfluorooctanoic acid (PFOA) adsorption results indicated that the maximum PFOA adsorption capacity was 1.19 and 1.89 mmol g(-1) for anionic-exchange MIL-101(Cr) prepared by PAM and PSM, respectively. The sorption equilibrium was rapidly reached within 60 min. Our results indicated that PSM is a better modification technique for introducing functional groups onto MOFs for adsorptive removal because PAM places functional groups onto the aperture of the nanopore, which hinders the entrance of organic contaminants. Our experimental results and the results of complementary density functional theory calculations revealed that in addition to the anion-exchange mechanism, the major PFOA adsorption mechanism is a combination of Lewis acid/base complexation between PFOA and Cr(III) and electrostatic interaction between PFOA and the protonated carboxyl groups of the bdc (terephthalic acid) linker. PMID:26066631

  10. Overcoming Rapid Inactivation of Lung Surfactant: Analogies Between Competitive Adsorption and Colloid Stability

    PubMed Central

    Zasadzinski, Joseph A.; Stenger, Patrick C.; Shieh, Ian; Dhar, Prajnaparamita

    2009-01-01

    Lung surfactant (LS) is a mixture of lipids and proteins that line the alveolar air-liquid interface, lowering the interfacial tension to levels that make breathing possible. In acute respiratory distress syndrome (ARDS), inactivation of LS is believed to play an important role in the development and severity of the disease. This review examines the competitive adsorption of LS and surface-active contaminants, such as serum proteins, present in the alveolar fluids of ARDS patients, and how this competitive adsorption can cause normal amounts of otherwise normal LS to be ineffective in lowering the interfacial tension. LS and serum proteins compete for the air-water interface when both are present in solution either in the alveolar fluids or in a Langmuir trough. Equilibrium favors LS as it has the lower equilibrium surface pressure, but the smaller proteins are kinetically favored over multi-micron LS bilayer aggregates by faster diffusion. If albumin reaches the interface, it creates an energy barrier to subsequent LS adsorption that slows or prevents the adsorption of the necessary amounts of LS required to lower surface tension. This process can be understood in terms of classic colloid stability theory in which an energy barrier to diffusion stabilizes colloidal suspensions against aggregation. This analogy provides qualitative and quantitative predictions regarding the origin of surfactant inactivation. An important corollary is that any additive that promotes colloid coagulation, such as increased electrolyte concentration, multivalent ions, hydrophilic non-adsorbing polymers such as PEG, dextran, etc. or polyelectrolytes such as chitosan, added to LS, also promotes LS adsorption in the presence of serum proteins and helps reverse surfactant inactivation. The theory provides quantitative tools to determine the optimal concentration of these additives and suggests that multiple additives may have a synergistic effect. A variety of physical and chemical

  11. Getting Freshman in Equilibrium.

    ERIC Educational Resources Information Center

    Journal of Chemical Education, 1983

    1983-01-01

    Various aspects of chemical equilibrium were discussed in six papers presented at the Seventh Biennial Conference on Chemical Education (Stillwater, Oklahoma 1982). These include student problems in understanding hydrolysis, helping students discover/uncover topics, equilibrium demonstrations, instructional strategies, and flaws to kinetic…

  12. Structure of Non-Equilibrium Adsorbed Polymer Layers

    NASA Astrophysics Data System (ADS)

    O'Shaughnessy, Ben; Vavylonis, Dimitrios

    2004-03-01

    Equilibrium polymer adsorption has been widely studied theoretically. Many experiments however implicate strong non-equilibrium effects for monomer sticking energies somewhat larger than kT, the most common case. The structure and slow dynamics in these layers is not understood. We analyze theoretically non-equilibrium layers from dilute solutions in the limit of irreversible monomer adsorption. We find the density profile ˜ z-4/3 and loop distribution ˜ s-11/5 of the resulting layer are no different to equilibrium. However, single chain statistics are radically different: the layer consists of a flat inner portion of fully collapsed chains plus an outer part whose chains make only fN surface contacts where N is chain length. The contact fractions f follow a broad distribution, P(f) ˜ f-4/5, consistent with experiment [H. M. Schneider et al, Langmuir 12, 994 (1996)], and the lateral size R of adsorbed chains is of order the bulk coil size, R ˜ N^3/5. For equilibrium layers, by contrast, P has a unique peak at a value of f of order unity, while R ˜ N^1/2 is significantly less. The relaxation of a non-equilibrium layer towards equilibrium thus entails chain shrinkage and tighter binding. We speculate that the observed decrease of bulk-layer chain exchange rates with increasing aging reflects these internal layer dynamics.

  13. Adsorption of Pyrene onto the Agricultural By-Product: Corncob.

    PubMed

    Li, Xiaojun; Tong, Dongli; Allinson, Graeme; Jia, Chunyun; Gong, Zongqing; Liu, Wan

    2016-01-01

    The adsorption behavior of pyrene on corncob was studied to provide a theoretical basis for the possible use of this material as an immobilized carrier for improving the bioremediation of PAH-contaminated soil. The results were as follows. Kinetic experiments showed that the adsorption processes obeyed a pseudo-second-order model. The intraparticle diffusion of Weber-Morris model fitting showed that the film and intraparticle diffusions were the key rate-limiting processes, and the adsorption process mainly consisted of three steps: boundary layer diffusion and two intra-particle diffusions. Experimental adsorption data for pyrene were successfully described by the adsorption-partition equilibrium model. The maximum adsorption capacity at 25°C was 214.8 μg g(-1). The adsorption contribution decreased significantly when the Ce/Sw (the equilibrium concentration/solubility in water) was higher than 1. Adsorption decreased with increased temperature. Based on the above results, the corncob particles could be helpful in the bioremediation of pyrene-contaminated soil. PMID:26573838

  14. Fluorocarbon Adsorption in Hierarchical Porous Frameworks

    SciTech Connect

    Motkuri, Radha K.; Annapureddy, Harsha V.; Vijayakumar, M.; Schaef, Herbert T.; Martin, P F.; McGrail, B. Peter; Dang, Liem X.; Krishna, Rajamani; Thallapally, Praveen K.

    2014-07-09

    The adsorption behavior of a series of fluorocarbon derivatives was examined on a set of microporous metal organic framework (MOF) sorbents and another set of hierarchical mesoporous MOFs. The microporous M-DOBDC (M = Ni, Co) showed a saturation uptake capacity for R12 of over 4 mmol/g at a very low relative saturation pressure (P/Po) of 0.02. In contrast, the mesoporous MOF MIL-101 showed an exceptionally high uptake capacity reaching over 14 mmol/g at P/Po of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption were found to generally correlate with the polarizability of the refrigerant with R12 > R22 > R13 > R14 > methane. These results suggest the possibility of exploiting MOFs for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling and refrigeration applications.

  15. Moisture adsorption isotherms and glass transition temperature of pectin.

    PubMed

    Basu, Santanu; Shivhare, U S; Muley, S

    2013-06-01

    The moisture adsorption isotherms of low methoxyl pectin were determined at 30-70°C and water activity ranging from 0.11 to 0.94. The moisture adsorption isotherms revealed that the equilibrium moisture content increased with water activity. Increase in temperature, in general, resulted in decreased equilibrium moisture content. However in some cases, equilibrium moisture content values increased with temperature at higher water activities. Selected sorption models (GAB, Halsey, Henderson, Oswin, modified Oswin) were tested for describing the adsorption isotherms. Parameters of each sorption models were determined by nonlinear regression analysis. Oswin model gave the best fit for pectin sorption behaviour. Isosteric heat of sorption decreased with increase in moisture content and varied between 14.607 and 0.552 kJ/mol. Glass transition temperature decreased with increase in moisture content of pectin. PMID:24425957

  16. Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite

    PubMed Central

    Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

    2015-01-01

    Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g·L-1, in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics. PMID:26698573

  17. Adsorption of tetrahydrothiophene (THT) onto soils

    NASA Astrophysics Data System (ADS)

    Juriga, Martin; Kubinec, Róbert; Rajzinger, Ján; Jelemenský, Karol; Gužela, Štefan

    2014-08-01

    Adsorption is one of the major industrial separation technique nowadays. Although adsorption is most commonly used as a separation method, in some cases cause harmful and undesirable effects such as capture odorant from natural gas onto soil. In the event of an accident, the gas can leak from pipes in two ways - either directly into the surrounding air, or the soil where the odorant can be mostly absorbed depending of type of soil, water content and temperature. Design of experimental apparatus for measurement of breakthrough curves is studied in detail. Alternative arrangement of experimental apparatus, calibration of measuring devices, method of measurement and processing the data are narrowly discussed. Moreover, experimental measurements of breakthrough curves are presented. The actual measurement was made to identify the equilibrium adsorption capacity of THT (tetrahydrothiophene) onto soils. Experimental data were evaluated using Linear, Freundlich, Langmuir and Koble-Corrigan model.

  18. [Thermodynamics adsorption and its influencing factors of chlorpyrifos and triazophos on the bentonite and humus].

    PubMed

    Zhu, Li-Jun; Zhang, Wei; Zhang, Jin-Chi; Zai, De-Xin; Zhao, Rong

    2010-11-01

    The adsorption of chlorpyrifos and triazophos on bentonite and humus was investigated by using the equilibrium oscillometry. The adsorption capacity of chlorpyrifos and triazophos on humus was great higher than bentonite at the same concentration. Equilibrium data of Langmuir, Freundlich isotherms showed significant relationship to the adsorption of chlorpyrifos and triazophos on humus (chlorpyrifos: R2 0.996 4, 0.996 3; triazophos: R2 0.998 9, 0.992 4). Langmuir isotherm was the best for chlorpyrifos and triazophos on bentonite (chlorpyrifos: R2 = 0.995 7, triazophos: R2 = 0.998 9). The pH value, adsorption equilibrium time and temperature were the main factors affecting adsorption of chlorpyrifos and triazophos on bentonite and humus. The adsorption equilibrium time on mixed adsorbent was 12h for chlorpyrifos and 6h for triazophos respectively. The mass ratio of humus and bentonite was 12% and 14% respectively, the adsorption of chlorpyrifos and triazophos was the stronglest and tended to saturation. At different temperatures by calculating the thermodynamic parameters deltaG, deltaH and deltaS, confirmed that the adsorption reaction was a spontaneous exothermic process theoretically. The adsorption was the best when the pH value was 6.0 and the temperature was 15 degrees C. PMID:21250454

  19. Adsorption and Separation Modeling of Porous Networks

    NASA Astrophysics Data System (ADS)

    Malanoski, Anthony; van Swol, Frank

    2001-03-01

    With the advent of self-assembly techniques has come the potential to tailor materials for adsorption and separation applications. For example, using surfactants as templating agents it is now feasible to finely control both the three-dimensional (3D) porosity as well as the surface chemistry. With an eye on assisting the emerging materials design we have embarked on a program that focuses on modeling adsorption/desorption, reactions and permeation phenomena in such structures. What makes the modeling particularly challenging is the coupling of length scales. The role of the atomic length scale features such as surface reactions and surface structure must be captured as well as the role of the network connectivity and other larger length scales. The latter include the pore shape and length, and the presence of external surfaces. This paper reports on how we employ refineable lattice models to tackle the modeling problems. We use both equilibrium and non-equilibrium Monte Carlo (MC) and 3D density functional theory (DFT) techniques to study the equilibrium and transport behavior in nanostructured porous materials. We will present 1) results of both adsorption/desorption hysteresis in large regular and random networks and 2) the results of using reactive sites in separation membranes, and compare these with experiments.

  20. Gas separation by adsorption in carbon nanohorns

    NASA Astrophysics Data System (ADS)

    Nekhai, Anton; Gatica, Silvina

    Gas separation by adsorption can be accomplished by three basic physical mechanisms: equilibria, kinetics, and steric effects. Equilibrium mechanisms rely on the strength of attraction between gas molecules and their substrate. For example, CO2 possesses the strongest, attractive interactions with its substrate. As a result, the equilibrium mechanism presents the most plausible strategy to separate carbon dioxide from mixtures. The specification of a sound adsorbent is the key for separation by adsorption. In this paper we investigate carbon nanohrons for selectivity of carbon dioxide over methane. Carbon Nanohorns resemble short, wide, highly defected single-wall nanotubes that end in conical tips (``horns''). In contrast to regular nanotubes that assemble into parallel bundles, nanohorns form spherical aggregates with the nanohorns arranged along radial directions. Using the simulation technique Grand Canonical Monte Carlo (GCMC) we obtained the adsorption isotherms of CH4 and CO2 in a 2D array of carbon nanohorns. We estimated the selectivity based on the IAST approximation. We also study the adsorption of argon and neon and compare with experimental results. We acknowledge support from the Partnership for Reduced Dimension Materials (PRDM), NSF Grant No. DMR1205608.

  1. Influence of soil solution cation composition on boron adsorption by soils

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Boron (B) adsorption on five arid-zone soil samples from California was investigated as a function of solution pH (4-10) and cation composition (Na, Ca, or Mg). Boron adsorption increased with increasing solution pH, reached an adsorption maximum near pH 9, and decreased with further increases with...

  2. Mercury adsorption properties of sulfur-impregnated adsorbents

    USGS Publications Warehouse

    Hsi, N.-C.; Rood, M.J.; Rostam-Abadi, M.; Chen, S.; Chang, R.

    2002-01-01

    Carbonaceous and noncarbonaceous adsorbents were impregnated with elemental sulfur to evaluate the chemical and physical properties of the adsorbents and their equilibrium mercury adsorption capacities. Simulated coal combustion flue gas conditions were used to determine the equilibrium adsorption capacities for Hg0 and HgCl2 gases to better understand how to remove mercury from gas streams generated by coal-fired utility power plants. Sulfur was deposited onto the adsorbents by monolayer surface deposition or volume pore filling. Sulfur impregnation increased the total sulfur content and decreased the total and micropore surface areas and pore volumes for all of the adsorbents tested. Adsorbents with sufficient amounts of active adsorption sites and sufficient microporous structure had mercury adsorption capacities up to 4,509 ??g Hg/g adsorbent. Elemental sulfur, organic sulfur, and sulfate were formed on the adsorbents during sulfur impregnation. Correlations were established with R2>0.92 between the equilibrium Hg0/HgCl2 adsorption capacities and the mass concentrations of elemental and organic sulfur. This result indicates that elemental and organic sulfur are important active adsorption sites for Hg0 and HgCl2.

  3. Chemical Principles Revisited: Chemical Equilibrium.

    ERIC Educational Resources Information Center

    Mickey, Charles D.

    1980-01-01

    Describes: (1) Law of Mass Action; (2) equilibrium constant and ideal behavior; (3) general form of the equilibrium constant; (4) forward and reverse reactions; (5) factors influencing equilibrium; (6) Le Chatelier's principle; (7) effects of temperature, changing concentration, and pressure on equilibrium; and (8) catalysts and equilibrium. (JN)

  4. Adsorption kinetics of Rhodamine-B on used black tea leaves

    PubMed Central

    2012-01-01

    Rhodamine B (Rh-B) is one of the most common pollutants in the effluents of textile industries effluents in developing countries. This study was carried out to evaluate the applicability of used black tea leaves (UBTL) for the adsorptive removal of Rh-B from aqueous system by investigating the adsorption kinetics in batch process. The effects of concentration and temperature on adsorption kinetics were examined. First-, second- and pseudo-second order kinetic equations were used to investigate the adsorption mechanism. The adsorption of Rh-B on UBTL followed pseudo-second order kinetics. The equilibrium amount adsorbed and the equilibrium concentration were calculated from pseudo-second-order kinetic plots for different initial concentrations of Rh-B to construct the adsorption isotherm. The adsorption isotherm was well expressed by Langmuir equation. The maximum adsorption capacity of UBTL to Rh-B was found to be 53.2 mg/g at pH = 2.0. The equilibrium amount adsorbed, calculated from pseudo-second-order kinetic plots, increased with temperature increase. The positive value of enthalpy of adsorption, ΔHads = 31.22 kJ/mol, suggested that the adsorption of Rh-B on UBTL at pH = 2.0 is an endothermic process. PMID:23369452

  5. Computing Equilibrium Chemical Compositions

    NASA Technical Reports Server (NTRS)

    Mcbride, Bonnie J.; Gordon, Sanford

    1995-01-01

    Chemical Equilibrium With Transport Properties, 1993 (CET93) computer program provides data on chemical-equilibrium compositions. Aids calculation of thermodynamic properties of chemical systems. Information essential in design and analysis of such equipment as compressors, turbines, nozzles, engines, shock tubes, heat exchangers, and chemical-processing equipment. CET93/PC is version of CET93 specifically designed to run within 640K memory limit of MS-DOS operating system. CET93/PC written in FORTRAN.

  6. Removal of Cr(III) from chrome tanning wastewater by adsorption using two natural carbonaceous materials: Eggshell and powdered marble.

    PubMed

    Elabbas, Saliha; Mandi, Laila; Berrekhis, Fatima; Pons, Marie Noelle; Leclerc, Jean Pierre; Ouazzani, Naaila

    2016-01-15

    In the present paper, eggshell and powdered marble, two carbonaceous materials, were used to remove Cr(III) ions from a real chrome tanning wastewater. The effects of initial effluent pH, adsorbent dose, contact time and temperature were studied. The maximum uptake of chromium ions was obtained at pH 5.0 with the dose 20 g L(-1) and 12 g L(-1) for eggshell and powdered marble respectively. Adsorption equilibrium was reached after 14 h contact time for eggshell and only after 30 min for powdered marble. Under these conditions, almost 99% Cr(III) was removed from chrome tanning wastewater having an initial concentration of chromium of 3.21 g L(-1). Kinetic data were satisfactorily described by a pseudo-second order chemical sorption model. The equilibrium rate constant was notably greater for powdered marble than for eggshell with 1.142·10(-3) (g mg(-1) min(-1)) and 0.041·10(-3) (g mg(-1) min(-1)) respectively. The adsorption isotherm were well described by a Langmuir model and showed that the interaction of chromium with the two adsorbents surface is a localized monolayer adsorption with a smaller energy constant for the powdered marble than for eggshell (0.020 (L mg(-1)) and 0.083 (L mg(-1)) respectively). The powdered marble was able to adsorb faster a large amount of Cr (III) in comparison to eggshell. The use of a standardized lettuce seed bioassay allowed evaluating a better effectiveness of the Cr adsorption on the powdered marble, removing up to 40% of the treated effluent toxicity than by eggshell 25%. The powdered marble could be considered as an effective, low cost carbonaceous material to be used for chromium removal from tanning wastewater. PMID:26598282

  7. Water vapor adsorption on activated carbon preadsorbed with naphtalene.

    PubMed

    Zimny, T; Finqueneisel, G; Cossarutto, L; Weber, J V

    2005-05-01

    The adsorption of water vapor on a microporous activated carbon derived from the carbonization of coconut shell has been studied. Preadsorption of naphthalene was used as a tool to determine the location and the influence of the primary adsorbing centers within the porous structure of active carbon. The adsorption was studied in the pressure range p/p0=0-0.95 in a static water vapor system, allowing the investigation of both kinetic and equilibrium experimental data. Modeling of the isotherms using the modified equation of Do and Do was applied to determine the effect of preadsorption on the mechanism of adsorption. PMID:15797395

  8. Effective interactions in multisite cells for adsorption in microporous materials

    NASA Astrophysics Data System (ADS)

    Demontis, Pierfranco; Pazzona, Federico G.; Suffritti, Giuseppe B.

    2009-04-01

    Local, discrete models of self-interacting multisite adsorption cells have been shown to be able to provide a coarse-grained representation of equilibrium properties of small molecules adsorbed in nanoporous materials at the mesoscopic scale. In the present work we show how the essential statistical properties of a host cell of structured sites with multiple adsorption energies and particle-particle interactions (that is the partition function, the average energy, and the average number of guests close to the windows connecting the cell to its surroundings) can be reproduced by a less-structured cell with two occupancy-dependent adsorption energy levels.

  9. Reaching ignition in the tokamak

    SciTech Connect

    Furth, H.P.

    1985-06-01

    This review covers the following areas: (1) the physics of burning plasmas, (2) plasma physics requirements for reaching ignition, (3) design studies for ignition devices, and (4) prospects for an ignition project. (MOW)

  10. CO2 and humidity removal system for extended Shuttle missions - CO2, H2O, and trace contaminant equilibrium testing

    NASA Technical Reports Server (NTRS)

    Davis, S. H.; Kissinger, L. D.

    1977-01-01

    The equilibrium relationships for the co-adsorption of CO2 and H2O on an amine coated acrylic ester are presented. The equilibrium data collection and reduction techniques are discussed. Based on the equilibrium relationship, other modes of operation of systems containing HS-C are discussed and specific space applications for HS-C are presented. Equilibrium data for 10 compounds which are found as trace contaminants in closed environments are also presented.

  11. Adsorption of humic acids and trace metals in natural waters

    NASA Technical Reports Server (NTRS)

    Leung, W. H.

    1982-01-01

    Studies concerning the interactions between suspended hydrous iron oxide and dissolved humic acids and trace metals are reported. As a major component of dissolved organic matters and its readiness for adsorption at the solid/water interface, humic acids may play a very important role in the organometallic geochemistry of suspended sediments and in determining the fate and distribution of trace metals, pesticides and anions in natural water systems. Most of the solid phases in natural waters contain oxides and hydroxides. The most simple promising theory to describe the interactions of hydrous iron oxide interface is the surface complex formation model. In this model, the adsorptions of humic acids on hydrous iron oxide may be interpreted as complex formation of the organic bases (humic acid oxyanions) with surface Fe ions. Measurements on adsorptions were made in both fresh water and seawater. Attempts have been made to fit our data to Langmuir adsorption isotherm. Adsorption equilibrium constants were determined.

  12. Adsorption behavior of perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) on boehmite.

    PubMed

    Wang, Fei; Liu, Chengshuai; Shih, Kaimin

    2012-11-01

    Understanding the interaction of perfluorochemicals, persistent pollutants with known human health effects, with mineral compounds in surface water and groundwater environments is essential to determining their fate and transport. Kinetic experiments showed that adsorption equilibrium can be achieved within 48 h and the boehmite (AlOOH) surface is receptive to perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) adsorption. The adsorption isotherms estimated the maximum adsorption capacities of PFOS and PFOA on boehmite as 0.877 μg m(-2) and 0.633 μg m(-2), respectively. Compared to the adsorption capacity on γ-alumina, the abundant hydroxyl groups on boehmite surfaces resulted in the 2-3 times higher adsorption of PFOS and PFOA. Increasing solution pH led to a moderate decrease in PFOS and PFOA adsorption, owing to an increase in ligand exchange reactions and the decrease of electrostatic interactions. The presence of NaCl and CaCl(2) in solution demonstrated negative effects for PFOS and PFOA adsorption on boehmite surfaces, with potential mechanisms being electrical double layer compression, competitive adsorption of chloride, and the Ca(2+) bridging effect between perfluorochemicals. PMID:22897837

  13. Adsorption of bovine serum albumin on nanosized magnetic particles.

    PubMed

    Peng, Z G; Hidajat, K; Uddin, M S

    2004-03-15

    Adsorption of bovine serum albumin (BSA) on nanosized magnetic particles (Fe(3)O(4)) was carried out in the presence of carbodiimide. The equilibrium and kinetics of the adsorption process were studied. Nanosized magnetic particles (Fe(3)O(4)) were prepared by the chemical precipitation method using Fe2+, Fe3+ salts, and ammonium hydroxide under a nitrogen atmosphere. Characterizations of magnetic particles were carried out using transmission electron microscopy (TEM) and a vibrating sample magnetometer (VSM). Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to confirm the attachment of BSA on magnetic particles. Effects of pH and salt concentrations were investigated on the adsorption process. The experimental results show that the adsorption of BSA on magnetic particles was affected greatly by the pH, while the effect of salt concentrations was insignificant at a low concentration range. The adsorption equilibrium isotherm was fitted well by the Langmuir model. The maximum adsorption of BSA on magnetic particles occurred at the isoelectric point of BSA. Adsorption kinetics was analyzed by a linear driving force mass-transfer model. BSA was desorbed from magnetic particles under alkaline conditions, which was confirmed by SDS-PAGE electrophoresis and FTIR results. PMID:14972603

  14. Effect of grain size on uranium(VI) surface complexation kinetics and adsorption additivity.

    PubMed

    Shang, Jianying; Liu, Chongxuan; Wang, Zheming; Zachara, John M

    2011-07-15

    The contribution of variable grain sizes to uranium adsorption/desorption was studied using a sediment from the US DOE Hanford site. The sediment was wet sieved into four size fractions: coarse sand (1-2 mm), medium sand (0.2-1 mm), fine sand (0.053-0.2 mm), and clay/silt fraction (<0.053 mm). For each size fraction and their composite (sediment), batch and flow-cell experiments were performed to determine uranium adsorption isotherms and kinetic uranium adsorption and subsequent desorption. The results showed that uranium adsorption isotherms and adsorption/desorption kinetics were size specific, reflecting the effects of size-specific adsorption site concentration and kinetic rate constants. The larger-size fraction had a larger mass percentage in the sediment but with a smaller adsorption site concentration and generally a slower uranium adsorption/desorption rate. The same equilibrium surface complexation reaction and reaction constant could describe uranium adsorption isotherms for all size fractions and the composite after accounting for the effect of adsorption site concentration. Mass-weighted, linear additivity was observed for both uranium adsorption isotherms and adsorption/desorption kinetics in the composite. One important implication of this study is that grain-size distribution may be used to estimate uranium adsorption site and adsorption/desorption kinetic rates in heterogeneous sediments from a common location. PMID:21648458

  15. Prediction of iodide adsorption on oxides by surface complexation modeling with spectroscopic confirmation.

    PubMed

    Nagata, Takahiro; Fukushi, Keisuke; Takahashi, Yoshio

    2009-04-15

    A deficiency in environmental iodine can cause a number of health problems. Understanding how iodine is sequestered by materials is helpful for evaluating and developing methods for minimizing human health effects related to iodine. In addition, (129)I is considered to be strategically important for safety assessment of underground radioactive waste disposal. To assess the long-term stability of disposed radioactive waste, an understanding of (129)I adsorption on geologic materials is essential. Therefore, the adsorption of I(-) on naturally occurring oxides is of environmental concern. The surface charges of hydrous ferric oxide (HFO) in NaI electrolyte solutions were measured by potentiometric acid-base titration. The surface charge data were analyzed by means of an extended triple-layer model (ETLM) for surface complexation modeling to obtain the I(-) adsorption reaction and its equilibrium constant. The adsorption of I(-) was determined to be an outer-sphere process from ETLM analysis, which was consistent with independent X-ray absorption near-edge structure (XANES) observation of I(-) adsorbed on HFO. The adsorption equilibrium constants for I(-) on beta-TiO(2) and gamma-Al(2)O(3) were also evaluated by analyzing the surface charge data of these oxides in NaI solution as reported in the literature. Comparison of these adsorption equilibrium constants for HFO, beta-TiO(2), and gamma-Al(2)O(3) based on site-occupancy standard states permitted prediction of I(-) adsorption equilibrium constants for all oxides by means of the Born solvation theory. The batch adsorption data for I(-) on HFO and amorphous aluminum oxide were reasonably reproduced by ETLM with the predicted equilibrium constants, confirming the validity of the present approach. Using the predicted adsorption equilibrium constants, we calculated distribution coefficient (K(d)) values for I(-) adsorption on common soil minerals as a function of pH and ionic strength. PMID:19176225

  16. Local non-equilibrium thermodynamics

    PubMed Central

    Jinwoo, Lee; Tanaka, Hajime

    2015-01-01

    Local Shannon entropy lies at the heart of modern thermodynamics, with much discussion of trajectory-dependent entropy production. When taken at both boundaries of a process in phase space, it reproduces the second law of thermodynamics over a finite time interval for small scale systems. However, given that entropy is an ensemble property, it has never been clear how one can assign such a quantity locally. Given such a fundamental omission in our knowledge, we construct a new ensemble composed of trajectories reaching an individual microstate, and show that locally defined entropy, information, and free energy are properties of the ensemble, or trajectory-independent true thermodynamic potentials. We find that the Boltzmann-Gibbs distribution and Landauer's principle can be generalized naturally as properties of the ensemble, and that trajectory-free state functions of the ensemble govern the exact mechanism of non-equilibrium relaxation. PMID:25592077

  17. Local non-equilibrium thermodynamics.

    PubMed

    Jinwoo, Lee; Tanaka, Hajime

    2015-01-01

    Local Shannon entropy lies at the heart of modern thermodynamics, with much discussion of trajectory-dependent entropy production. When taken at both boundaries of a process in phase space, it reproduces the second law of thermodynamics over a finite time interval for small scale systems. However, given that entropy is an ensemble property, it has never been clear how one can assign such a quantity locally. Given such a fundamental omission in our knowledge, we construct a new ensemble composed of trajectories reaching an individual microstate, and show that locally defined entropy, information, and free energy are properties of the ensemble, or trajectory-independent true thermodynamic potentials. We find that the Boltzmann-Gibbs distribution and Landauer's principle can be generalized naturally as properties of the ensemble, and that trajectory-free state functions of the ensemble govern the exact mechanism of non-equilibrium relaxation. PMID:25592077

  18. Adsorption of phenanthrene on natural snow.

    PubMed

    Domine, Florent; Cincinelli, Alessandra; Bonnaud, Elodie; Martellini, Tania; Picaud, Sylvain

    2007-09-01

    The snowpack is a reservoir for semivolatile organic compounds (SVOCs) and, in particular, for persistent organic pollutants (POPs), which are sequestered in winter and released to the atmosphere or hydrosphere in the spring. Modeling these processes usually assumes that SVOCs are incorporated into the snowpack by adsorption to snow surfaces, but this has never been proven because the specific surface area (SSA) of snow has never been measured together with snow composition. Here we expose natural snow to phenanthrene vapors (one of the more volatile POPs) and measure for the first time both the SSA and the chemical composition of the snow. The results are consistent with an adsorption equilibrium. The measured Henry's law constant is H(Phen)(T) = 2.88 x 10(22) exp(-10660/7) Pa m2 mol(-1), with Tin Kelvin. The adsorption enthalpy is delta H(ads) = -89 +/- 18 kJ mol(-1). We also perform molecular dynamics calculations of phenanthrene adsorption to ice and obtain AHads = -85 +/- 8 kJ mol(-1), close to the experimental value. Results are applied to the adsorption of phenanthrene to the Arctic and subarctic snowpacks. The subarctic snowpack, with a low snow area index (SAI = 1000), is a negligible reservoir of phenanthrene, butthe colder Arctic snowpack, with SAI = 2500, sequesters most of the phenanthrene present in the (snow + boundary layer) system. PMID:17937278

  19. Simulated Water Adsorption Isotherms in Hydrophilic and Hydrophobic Cylinderical Nanopores

    SciTech Connect

    StrioloDr., A; Naicker, P. K.; Chialvo, Ariel A; Cummings, Peter T; Gubbins, Dr. K. E.

    2005-01-01

    Grand canonical Monte Carlo simulations are performed to study the adsorption of water in single-walled carbon nanotubes (SWCNs). At room temperature the resulting adsorption isotherms in (10:10) and wider SWCNs are characterized by negligible amount of water uptake at low pressures, sudden and complete pore filling once a threshold pressure is reached, and wide adsorption/desorption hysteresis loops. The width of these loops decreases as pore diameter narrows. Adsorption/desorption hysteresis loops are not observed for water adsorption in (6:6) SWCNs. When the nanotubes are doped with small amounts of oxygenated sites it is possible to obtain adsorption isotherms in which the water uptake increases gradually as the pressure increases. Simulated X-ray diffraction patterns for confined water are also reported.

  20. Adsorption and regenerative oxidation of trichlorophenol with synthetic zeolite: Ozone dosage and its influence on adsorption performance.

    PubMed

    Zhang, Yongjun; Prigent, Bastien; Geißen, Sven-Uwe

    2016-07-01

    Regeneration of loaded adsorbents is a key step for the sustainability of an adsorption process. In this study, ozone was applied to regenerate a synthetic zeolite for the adsorption of trichlorophenol (TCP) as an organic model pollutant. Three initial concentrations of TCP in water phase were used in adsorption tests. After the equilibrium, zeolite loaded different amounts of TCP was dried and then regenerated with ozone gas. It was found that the adsorption capacity of zeolite was increased through three regeneration cycles. However, the adsorption kinetics was compromised after the regeneration with slightly declined 2nd order reaction constants. The ozone demand for the regeneration was highly dependent on the TCP mass loaded onto the zeolite. It was estimated that the mass ratio of ozone to TCP was 1.2 ± 0.3 g O3/g TCP. PMID:27043379

  1. [Characteristic of ammonia nitrogen adsorption on karst underground river sediments].

    PubMed

    Guo, Fang; Chen, Kun-Kun; Jiang, Guang-Hui

    2011-02-01

    Karst aquifers are one of the most important aquifers in Southwestern China. One of the characteristics of karst aquifers is the enhanced permeability permits high flow velocities are capable of transporting suspended and bedload sediments. Mobile sediment in karst may act as a vector for the transport of contaminates. 14 sediment samples were collected from two underground rivers in two typical karst areas in Liuzhou city, Guangxi Autonomous Region, China. According to simulated experiment methods, characteristic of adsorption of ammonia nitrogen on sediment was studied. The results of ammonia nitrogen adsorption dynamics on sediments showed that the maximum adsorption velocity was less than 2 h. The adsorption balance quantity in 5 h accounted for 71% - 98% of the maximum adsorption quantity. The maximum adsorption quantity of ammonia nitrogen was 385.5 mg/kg, which was sediment from a cave in the middle areas of Guancun underground river system. The study of isotherm adsorption indicated adsorption quantity of NH4+ increase followed by incremental balance concentration of NH4+ in the aquatic phase. Adsorption quantity of ammonia nitrogen in sediments has a relative linear relationship with adsorption balance concentrations. Adsorption-desorption balance concentrations were all low, indicating sediments from underground rivers have great adsorption potential. Under the condition of low and high concentrations of ammonia nitrogen in overlying water, Langmuir and Tempkin couldn't simulate or simulate results couldn't reach remarkable level, whilst Linear and Freundlich models could simulate well. Research on different type sediments, sampling times and depths from two underground rivers shows characteristic of ammonia nitrogen adsorption on karst underground river sediments doesn't have good correspondence with the type of sediments. One of the reasons is there is no big difference between sediments in the development of climate, geology, hydrological conditions

  2. Adsorption of atrazine on soils: model study.

    PubMed

    Kovaios, Ilias D; Paraskeva, Christakis A; Koutsoukos, Petros G; Payatakes, Alkiviades Ch

    2006-07-01

    The adsorption of the widely used herbicide atrazine onto three model inorganic soil components (silica gel, gamma-alumina, and calcite (CaCO(3)) was investigated in a series of batch experiments in which the aqueous phase equilibrated with the solid, under different solution conditions. Atrazine did not show discernible adsorption on gamma-alumina (theta=25 degrees C, 3.8adsorption from solutions was found for silica gel suspensions. The adsorption isotherms obtained for atrazine uptake on silica gel particles were best fitted with the Freundlich model. An increase of the ionic strength of the electrolytic solution induced an increase of the surface concentration of atrazine on silica gel, indicating significant electrostatic interactions between atrazine and silica gel particles, possibly through interaction with the surface silanol groups of the solid substrate. Increase of the pH value of the electrolyte solution from 6 to 9 considerably decreased the amount of atrazine adsorbed on the silica gel substrate. Decrease of the solution pH from 6 to 3 had only a slight effect on the surface concentration of the adsorbed atrazine. The adsorption of atrazine on silica gel increased when the temperature was decreased from 40 to 25 degrees C, an indication that the adsorption is exothermic. The calculated enthalpy of adsorption ( approximately 10 kJ/mol) indicates that the uptake at the solid-liquid equilibrium pH (6.1) was largely due to physisorption. PMID:16556447

  3. Phosphate adsorption on aluminum-coordinated functionalized macroporous–mesoporous silica: Surface structure and adsorption behavior

    SciTech Connect

    Huang, Weiya; Li, Dan; Zhu, Yi; Xu, Kai; Li, Jianqiang; Han, Boping; Zhang, Yuanming

    2013-12-15

    Graphical abstract: - Highlights: • Al-coordinated functionalized macroporous–mesoporous silica for phosphate removal. • It had the maximum adsorption capacity of 23.59 mg P/g. • Over 95% of the final adsorption capacity reached in the first 1 min. - Abstract: In this study, Al(III)-coordinated diamino-functionalized macroporous–mesoporous silica was synthesized and characterized by X-ray diffraction, N{sub 2} adsorption–desorption, Fourier transform infrared spectroscopy, scanning and transmission electron microscopy. Because of well-defined and interconnecting macroporous–mesoporous networks, the resulting adsorbent (MM-SBA) exhibited a significantly better phosphate adsorption performance and faster removal rate, as compared with the mesoporous adsorbent (M-SBA). Based on the Freundlich and Langmuir models, the phosphate adsorption capacity and the maximum adsorption capacity of MM-SBA were 7.99 mg P/g and 23.59 mg P/g, respectively. In the kinetic study of MM-SBA, over 95% of its final adsorption capacity reached in the first 1 min; whereas that of M-SBA was less than 79%.

  4. Equilibrium and non-equilibrium dynamics simultaneously operate in the Galápagos islands.

    PubMed

    Valente, Luis M; Phillimore, Albert B; Etienne, Rampal S

    2015-08-01

    Island biotas emerge from the interplay between colonisation, speciation and extinction and are often the scene of spectacular adaptive radiations. A common assumption is that insular diversity is at a dynamic equilibrium, but for remote islands, such as Hawaii or Galápagos, this idea remains untested. Here, we reconstruct the temporal accumulation of terrestrial bird species of the Galápagos using a novel phylogenetic method that estimates rates of biota assembly for an entire community. We show that species richness on the archipelago is in an ascending phase and does not tend towards equilibrium. The majority of the avifauna diversifies at a slow rate, without detectable ecological limits. However, Darwin's finches form an exception: they rapidly reach a carrying capacity and subsequently follow a coalescent-like diversification process. Together, these results suggest that avian diversity of remote islands is rising, and challenge the mutual exclusivity of the non-equilibrium and equilibrium ecological paradigms. PMID:26105791

  5. Equilibrium versus disequilibrium of barchan dunes

    NASA Astrophysics Data System (ADS)

    El belrhiti, Hicham; Douady, Stéphane

    2011-02-01

    Barchans are crescentic dunes which occur in mainly mono-directional winds. Shape, aspect ratios and velocities of these dunes have been studied as if they were in equilibrium. However, following a study of the shape and migration of 11 barchans of different sizes for 18 months in the field on Moroccan Atlantic Sahara, we show that they only appear to be in a stationary state if studied over a long timeframe (at the scale of the year or several years), but are never in equilibrium at the scale of weeks or months. Rather, they are always 'trying' to reach a possible equilibrium state but never have enough time to accomplish this. This may be the main reason for the large variation observed in previous measurements, and justifies some caution in what can be deduced from them.

  6. Equilibrium games in networks

    NASA Astrophysics Data System (ADS)

    Li, Angsheng; Zhang, Xiaohui; Pan, Yicheng; Peng, Pan

    2014-12-01

    It seems a universal phenomenon of networks that the attacks on a small number of nodes by an adversary player Alice may generate a global cascading failure of the networks. It has been shown (Li et al., 2013) that classic scale-free networks (Barabási and Albert, 1999, Barabási, 2009) are insecure against attacks of as small as O(logn) many nodes. This poses a natural and fundamental question: Can we introduce a second player Bob to prevent Alice from global cascading failure of the networks? We proposed a game in networks. We say that a network has an equilibrium game if the second player Bob has a strategy to balance the cascading influence of attacks by the adversary player Alice. It was shown that networks of the preferential attachment model (Barabási and Albert, 1999) fail to have equilibrium games, that random graphs of the Erdös-Rényi model (Erdös and Rényi, 1959, Erdös and Rényi, 1960) have, for which randomness is the mechanism, and that homophyly networks (Li et al., 2013) have equilibrium games, for which homophyly and preferential attachment are the underlying mechanisms. We found that some real networks have equilibrium games, but most real networks fail to have. We anticipate that our results lead to an interesting new direction of network theory, that is, equilibrium games in networks.

  7. Competitive adsorption of molybdenum in the presence of phosphorus or sulfur on gibbsite

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Anion adsorption on the aluminum oxide, gibbsite was investigated as a function of solution pH (3-11) and equilibrium solution Mo (3.13, 31.3, or 313 µM), P (96.9 µM), or S (156 µM)concentration. Adsorption of all three anions decreased with increasing pH. Electrophoretic mobility measurements indi...

  8. Application of surface complexation models to anion adsorption by natural materials

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Various chemical models of ion adsorption will be presented and discussed. Chemical models, such as surface complexation models, provide a molecular description of anion adsorption reactions using an equilibrium approach. Two such models, the constant capacitance model and the triple layer model w...

  9. BORONATE AFFINITY ADSORPTION OF RNA: POSSIBLE ROLE OF CONFORMATIONAL CHANGES. (R825354)

    EPA Science Inventory

    Batch equilibrium adsorption isotherm determination is used to characterize the adsorption of mixed yeast RNA on agarose-immobilized m-aminophenylboronic acid. It is shown that the affinity-enhancing influence of divalent cations depends strongly on the precise nature of t...

  10. Hydrogen and helium adsorption on potassium

    SciTech Connect

    Garcia, R.; Mulders, N.; Hess, G.

    1995-04-01

    A previous quartz microbalance study of adsorption of helium on sodium indicates that the inert layer is surprisingly small. Similar experiments with hydrogen on sodium show layer by layer growth below a temperature of 7K. These results motivated the authors to extend the experiments to lower temperatures. A suitable apparatus, capable of reaching 0.45 K, while still enabling them to do in situ alkali evaporation, has been constructed. The authors will report on the results of microbalance adsorption experiments of helium and hydrogen on potassium.

  11. Removal of water and iodine by solid sorbents: adsorption isotherms and kinetics

    SciTech Connect

    Lin, R.; Tavlarides, L.L.

    2013-07-01

    Tritium and iodine-129 are two major radioactive elements that are present in off-gases from spent fuel reprocessing plants. Adsorption by solid sorbents is the state-of-the-art technique for removal of these species from off-gases. Modeling and simulating adsorption processes require accurate adsorption equilibrium and kinetic data to permit reasonable estimates of process parameters. We have developed a continuous flow single-pellet adsorption system to gather accurate adsorption equilibrium and kinetic data for adsorption of water by molecular sieve 3A and for adsorption of iodine by silver exchanged mordenite. In this paper, the design of the water and iodine adsorption experimental systems are briefly described and results of water adsorption experiments are presented and discussed. Water uptake curves are fitted with the linear-driving force (LDF) model and the shrinking-core model to determine kinetic parameters. It is shown that the kinetics of water adsorption on zeolite 3A under current experimental conditions is controlled by both the external film resistance and the macro-pore diffusion and can be predicted by both the LDF model and the shrinking-core model with the former one performing slightly better. Preliminary results from iodine adsorption experiments will be presented in the conference.

  12. [Application of classical isothermal adsorption models in heavy metal ions/ diatomite system and related problems].

    PubMed

    Zhu, Jian; Wu, Qing-Ding; Wang, Ping; Li, Ke-Lin; Lei, Ming-Jing; Zhang, Wei-Li

    2013-11-01

    In order to fully understand adsorption nature of Cu2+, Zn2+, Pb2+, Cd2+, Mn2+, Fe3+ onto natural diatomite, and to find problems of classical isothermal adsorption models' application in liquid/solid system, a series of isothermal adsorption tests were conducted. As results indicate, the most suitable isotherm models for describing adsorption of Pb2+, Cd2+, Cu2+, Zn2+, Mn2+, Fe3+ onto natural diatomite are Tenkin, Tenkin, Langmuir, Tenkin, Freundlich and Freundlich, respectively, the adsorption of each ion onto natural diatomite is mainly a physical process, and the adsorption reaction is favorable. It also can be found that, when using classical isothermal adsorption models to fit the experimental data in liquid/solid system, the equilibrium adsorption amount q(e) is not a single function of ion equilibrium concentration c(e), while is a function of two variables, namely c(e) and the adsorbent concentration W0, q(e) only depends on c(e)/W(0). Results also show that the classical isothermal adsorption models have a significant adsorbent effect, and their parameter values are unstable, the simulation values of parameter differ greatly from the measured values, which is unhelpful for practical use. The tests prove that four-adsorption-components model can be used for describing adsorption behavior of single ion in nature diatomite-liquid system, its parameters k and q(m) have constant values, which is favorable for practical quantitative calculation in a given system. PMID:24455943

  13. Adsorption Refrigeration System

    SciTech Connect

    Wang, Kai; Vineyard, Edward Allan

    2011-01-01

    Adsorption refrigeration is an environmentally friendly cooling technology which could be driven by recovered waste heat or low-grade heat such as solar energy. In comparison with absorption system, an adsorption system has no problems such as corrosion at high temperature and salt crystallization. In comparison with vapor compression refrigeration system, it has the advantages of simple control, no moving parts and less noise. This paper introduces the basic theory of adsorption cycle as well as the advanced adsorption cycles such as heat and mass recovery cycle, thermal wave cycle and convection thermal wave cycle. The types, characteristics, advantages and drawbacks of different adsorbents used in adsorption refrigeration systems are also summarized. This article will increase the awareness of this emerging cooling technology among the HVAC engineers and help them select appropriate adsorption systems in energy-efficient building design.

  14. Protein nanoparticle interaction: A spectrophotometric approach for adsorption kinetics and binding studies

    NASA Astrophysics Data System (ADS)

    Vaishanav, Sandeep K.; Chandraker, Kumudini; Korram, Jyoti; Nagwanshi, Rekha; Ghosh, Kallol K.; Satnami, Manmohan L.

    2016-08-01

    Investigating the protein nanoparticle interaction is crucial to understand how to control the biological interactions of nanoparticles. In this work, Model protein Bovine serum albumin (BSA) was used to evaluate the process of protein adsorption to the gold nanoparticles (GNPs) surface. The binding of a model protein (BSA) to GNPs was investigated through fluorescence quenching measurements. The strong affinities of BSA for GNPs were confirmed by the high value of binding constant (Ks) which was calculated to be 2.2 × 1011 L/mol. In this consequence, we also investigated the adsorption behavior of BSA on GNPs surface via UV-Vis spectroscopy. The effect of various operational parameters such as pH, contact time, initial BSA concentration, and temperature on adsorption of BSA was investigated using batch adsorption experiments. Kinetics of adsorption was found to follow the pseudo-second order rate equation. The suitability of Freundlich and Langmuir adsorption models to the equilibrium data was investigated. The equilibrium adsorption was well described by the Freundlich isotherm model. The maximum adsorption capacity for BSA adsorbed on GNPs was 58.71 mg/g and equilibrium constant was 0.0058 calculated by the Langmuir model at 298 K and pH = 11.0. Thermodynamic parameters showed that the adsorption of BSA onto GNPs was feasible, spontaneous, and exothermic.

  15. REACH. Residential Electrical Wiring Units.

    ERIC Educational Resources Information Center

    Ansley, Jimmy; Ennis, Mike

    As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of residential electrical wiring. The instructional units focus on grounded outlets, service entrance, and blueprint reading. Each unit follows a typical format…

  16. Project REACH Administrator's Manual. PRAM.

    ERIC Educational Resources Information Center

    Piuma, Chesca; And Others

    The final volume in a series on Project REACH (Regular Education for All Children with Handicaps) is addressed to administrators involved in integrating severely disabled students into regular public schools. The manual is intended as a trouble-shooting tool with information on background theories and specific strategies. An introductory chapter…

  17. PNW RIVER REACH FILE DOCUMENTATION

    EPA Science Inventory

    The U.S. Geological Survey (USGS) in cooperation with Federal and state agencies, and NW Indian Tribes has produced a 1:100,000-scale River Reach data layer for the Pacific Northwest that will serve water-resource management applications for the next decade or more. The Pacific N...

  18. Reaching the "iBored"

    ERIC Educational Resources Information Center

    Bauleke, Debra S.; Herrmann, Kathleen E.

    2010-01-01

    As teachers, they are always looking for creative ways to engage their students. They start the school year determined to bring to the classroom creative projects that generate student interest and foster critical thinking skills. Reaching today's Gen M student is challenging and changing the way they teach. The idea of using music to teach…

  19. Reaching All Students with Mathematics.

    ERIC Educational Resources Information Center

    Cuevas, Gilbert, Ed.; Driscoll, Mark, Ed.

    The National Council of Teachers of Mathematics'"Curriculum and Evaluation Standards for School Mathematics" and "Professional Standards for Teaching Mathematics" reflect the belief that all students can learn a significant core of high-quality mathematics. Recognizing the magnitude of the task of reaching all students, this book was put together…

  20. Adsorption of Phosphate on Goethite: An Undergraduate Research Laboratory Project

    ERIC Educational Resources Information Center

    Tribe, Lorena; Barja, Beatriz C.

    2004-01-01

    A laboratory experiment on the adsorption of phosphate on goethite is presented, which also includes discussion on surface properties, interfaces, acid-base equilibrium, molecular structure and solid state chemistry. It was seen that many students were able to produce qualitatively correct results for a complex system of real interest and they…

  1. [Adsorption characteristics of f2 bacteriophages by four substrates in constructed wetland].

    PubMed

    Chen, Di; Zheng, Xiang; Wei, Yuan-Song; Yang, Yong

    2013-10-01

    Performance of f2 phages adsorption by four substrates including anthracite coal, steel slag, zeolite and forsterite was investigated through batch and dynamic experiments. Results of batch experiments showed that the removal efficiency of f2 phages by these four substrates was in the order of anthracite > steel slag > forsterite approximately zeolite. The adsorption of f2 phages by anthracite experienced fast, medium and slow stages, and the removal efficiency of f2 phages increased gradually with the increase of anthracite dosage, e. g. the optimized dosage of anthracite was 8.0 g at a solid/liquid ratio of 1:12.5 (m/V). The isothermal adsorption of all four substrates was described with Freundlich and Langmuir isothermal adsorption equation very well, and the adsorption of f2 phages by both anthracite and steel slag fitted pseudo-second order adsorption kinetics at their theoretical adsorption capacities of 3. 35 x 10(8) PFU.g-1 and 2.56 x 10(8) PFU.g-1, respectively, nearly the same as the equilibrium adsorption capacities obtained under the experiment conditions. And the liquid diffusion process was a rate-limiting step of the adsorption of f2 phage by both anthracite and steel slag, but not the only one. The results of dynamic adsorption experiments showed that the adsorption process of f2 phages in the three adsorption columns including anthracite, steel slag and zeolite experienced four stages of adaption, adsorption, pulse adsorption and adsorption equilibrium, and the total removal rates of f2 phages were more than 2. 55 Ig. PMID:24364309

  2. Adsorption and photocatalytic degradation of anionic dyes on Chitosan/PVA/Na-Titanate/TiO2 composites synthesized by solution casting method.

    PubMed

    Habiba, Umma; Islam, Md Shariful; Siddique, Tawsif A; Afifi, Amalina M; Ang, Bee Chin

    2016-09-20

    Chitosan/PVA/Na-titanate/TiO2 composite was synthesized by solution casting method. The composite was analyzed via Fourier Transform Infrared Spectroscopy, X-ray diffraction, Field Emission Scanning Electron Microscopy, Thermal gravimetric analysis and water stability test. Incorporation of Na-titanate shown decrease of crystallinity for chitosan but increase water stability. However, the composite structure was deteriorated with considerable weight loss in acidic medium. Two anionic dyes, methyl orange and congo red were used for the adsorption test. The adsorption behavior of the composites were described by pseudo-second-order kinetic model and Lagergren-first-order model for methyl orange and congo red, respectively. For methyl orange, adsorption was started with a promising decolorization rate. 99.9% of methyl orange dye was removed by the composite having higher weightage of chitosan and crystalline TiO2 phase. On the other hand, for the congo red the composite having higher chitosan and Na-titanate showed an efficient removal capacity of 95.76%. UV-vis results showed that the molecular backbone of methyl orange and congo red was almost destroyed when equilibrium was obtained, and the decolorization rate was reaching 100%. Kinetic study results showed that the photocatalytic degradation of methyl orange and congo red could be explained by Langmuir-Hinshelwood model. Thus, chitosan/PVA/Na-titanate/TiO2 possesses efficient adsorptivity and photocatalytic property for dye degradation. PMID:27261756

  3. Ultrasonic assisted arsenate adsorption on solvothermally synthesized calcite modified by goethite, α-MnO2 and goethite/α-MnO2.

    PubMed

    Markovski, Jasmina S; Đokić, Veljko; Milosavljević, Milutin; Mitrić, Miodrag; Perić-Grujić, Aleksandra A; Onjia, Antonije E; Marinković, Aleksandar D

    2014-03-01

    A highly porous calcium carbonate (calcite; sorbent 1) was used as a support for modification with α-FeOOH (calcite/goethite; sorbent 2), α-MnO2 (calcite/α-MnO2; sorbent 3) and α-FeOOH/α-MnO2 (calcite/goethite/α-MnO2; sorbent 4) in order to obtain a cheap hybrid materials for simple and effective arsenate removal from aqueous solutions. The adsorption ability of synthesized adsorbents was studied as a function of functionalization methods, pH, contact time, temperature and ultrasonic treatment. Comparison of the adsorptive effectiveness of synthesized adsorbents for arsenate removal, under ultrasound treatment and classical stirring method, has shown better performance of the former one reaching maximum adsorption capacities of 1.73, 21.00, 10.36 and 41.94 mg g(-1), for sorbents 1-4, respectively. Visual MINTEQ equilibrium speciation modeling was used for prediction of pH and interfering ion influences on arsenate adsorption. PMID:24210695

  4. Adsorption of mercury on laterite from Guizhou Province, China.

    PubMed

    Yu, Xiaohong; Zhu, Lijun; Guo, Baiwei; He, Shouyang

    2008-01-01

    The adsorption behaviors of Hg(II) on laterite from Guizhou Province, China, were studied and the adsorption mechanism was discussed. The results showed that different mineral compositons in the laterite will cause differences in the adsorption capacity of laterite to Hg(II). Illite and non-crystalloids are the main contributors to enhancing the adsorption capacity of laterite to Hg(II). The pH of the solution is an important factor affecting the adsorption of Hg(II) on laterite. The alkalescent environment (pH 7-9) is favorable to the adsorption of Hg(II). The amount of adsorbed Hg(II) increases with increasing pH. When the pH reaches a certain value, the amount of the adsorbed Hg(II) will reach the maximum level. The amount of adsorbed Hg(II) decreases with increasing pH. The optimal pHs of laterite and kaolinite are 9 and 8, respectively. The optimal initial concentrations of Hg(II) on laterite and kaolinite are 250 and 200 microg/ml, respectively. The adsorption isotherms were described by the Langmuir model. The adsorption of Hg(II) on laterite is a quick process while that of Hg(II) on kaolinite is a slow reaction. Laterite from Guizhou Province is a promising environmental material which can be used in the removal of Hg(II) from wastewater. PMID:19202872

  5. Carbon dioxide adsorption in Brazilian coals

    SciTech Connect

    Jose Luciano Soares; Andre L.B. Oberziner; Humberto J. Jose; Alirio E. Rodrigues; Regina F.P.M. Moreira

    2007-01-15

    Carbon dioxide (CO{sub 2}) is one of the most important greenhouse gases. In the period between 1980 and 1998, CO{sub 2} emissions increased more than 21% and projections suggest that the emissions will continue to increase globally by 2.2% between 2000 and 2020 and 3.3% in the developed countries. The sequestration of CO{sub 2} in deep unminable coal beds is one of the more promising of several methods of geological sequestration that are currently being investigated. CO{sub 2} can adsorb onto coal, and there are several studies demonstrating that CO{sub 2} dissolves in coals and swells them. At very low pressures (P {lt} 1 bar), CO{sub 2} dissolution does not seem to be a problem; however, high pressures are necessary for CO{sub 2} sequestration (P {gt} 50 bar). In this study, we evaluated the kinetics and equilibrium of sorption of CO{sub 2} on Brazilian coals at low pressures. The adsorption equilibrium isotherm at room temperature (30{sup o}C) was measured through the static method. The results showed that the Freundlich model or the Langmuir model is suitable to describe the equilibrium experimental results. The CO{sub 2} adsorption capacity of Brazilian coals are in the range of 0.089-0.186 mmol CO{sub 2}/g, which are typical values for coals with high ash content. The dynamics of adsorption in a fixed-bed column that contains granular coal (particle sizes of 0.8, 2.4, and 4.8 mm) showed that the adsorption rate is fast and a mathematical model was developed to describe the CO{sub 2} dynamics of the adsorption in a fixed-bed column. The linear driving force (LDF) was used to describe the rate of adsorption and the mass-transfer constants of the LDF model (K{sub s}) are in the range of 1.0-2.0 min{sup -1}. 29 refs., 5 figs., 3 tabs.

  6. An Updated Equilibrium Machine

    ERIC Educational Resources Information Center

    Schultz, Emeric

    2008-01-01

    A device that can demonstrate equilibrium, kinetic, and thermodynamic concepts is described. The device consists of a leaf blower attached to a plastic container divided into two chambers by a barrier of variable size and form. Styrofoam balls can be exchanged across the barrier when the leaf blower is turned on and various air pressures are…

  7. A thermodynamic model for gas adsorption isotherms

    SciTech Connect

    Riazi, M.R.; Khan, A.R.

    1999-02-15

    In this paper based on the principle of solution thermodynamics for gas-solid equilibrium, a relation is developed to express gas adsorption isotherms. An activity coefficient model based on weight fraction of sorbate in the solid phase has been derived that well describes the behavior of various gases on different types of adsorbents. The proposed model has been evaluated and compared with four other models commonly used for gas adsorption isotherms in the literature. For 12 different systems at various isotherms for the temperature range {minus}128 to 100 C and the pressure range 0.02 to 1219 kPa for 689 data points, the proposed model predicts equilibrium pressure with an average deviation of 5.3%, which is about half of the error obtained from other methods. The proposed model clearly outperforms other available methods such as the vacancy solution theory, the ideal adsorption solution model, and other various modified forms of the Langmuir isotherm. Unique features of the proposed model are its simplicity, generality, and accuracy over the entire pressure and temperature ranges.

  8. [Adsorption of Congo red from aqueous solution on hydroxyapatite].

    PubMed

    Zhan, Yan-Hui; Lin, Jian-Wei

    2013-08-01

    The adsorption of Congo red (CR) from aqueous solution on hydroxyapatite was investigated using batch experiments. The hydroxyapatite was effective for CR removal from aqueous solution. The adsorption kinetics of CR on hydroxyapatite well followed a pseudo-second-order model. The equilibrium adsorption data of CR on hydroxyapatite could be described by the Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models. Thermodynamic parameters such as Gibbs free energy change, enthalpy change and entropy change were calculated and showed that the adsorption of CR on hydroxyapatite was spontaneous and exothermic in nature. The CR adsorption capacity for hydroxyapatite decreased significantly with increasing pH from 8 to 10. Thermal regeneration showed that hydroxyapatite could be used for six desorption-adsorption cycles with high removal efficiency for CR in each cycle. The mechanisms for CR adsorption on hydroxyapatite with pH value below the pH at point of zero charge (pH(PZC)) include electrostatic attraction, hydrogen bonding and Lewis acid-base interaction. The mechanisms for CR adsorption on hydroxyapatite with pH value above its pH(PZC) include hydrogen bonding and Lewis acid-base interaction. Results of this work indicate that hydroxyapatite is a promising adsorbent for CR removal from aqueous solution. PMID:24191561

  9. Facile synthesis of hairy core-shell structured magnetic polymer submicrospheres and their adsorption of bovine serum albumin.

    PubMed

    Yan, Xianming; Kong, Juan; Yang, Chongchong; Fu, Guoqi

    2015-05-01

    Highly magnetic polymer submicrospheres with a hairy core-shell structure were facilely synthesized by combining distillation-precipitation polymerization (DPP) with subsequent surface-initiated atom transfer radical polymerization (SI-ATRP), and then investigated for protein adsorption. A robust polymer shell consisting of poly(divinylbenzene-co-chloromethylstyrene) (P(DVB-co-CMS)) was coated on superparamagnetic submicrometer-sized magnetite colloid nanocrystal clusters (MCNCs) via DPP. With the benzyl chloride groups on the shell as initiator, poly(2-(dimethylamino) ethyl methacrylate) (PDMAEMA) hairs were grafted by SI-ATRP approach. The resulting hairy core-shell structured Fe3O4@ P(DVB-co-CMS)-PDMAEMA microspheres showed pH- and temperature-sensitivity, and high-magnetization. The composite microspheres were further investigated for adsorption of a typical acidic protein, i.e. bovine serum albumin (BSA). They exhibited a high binding capacity up to over 660 mg/g (corresponding to 158 DMAEMA monomer units cooperating for binding one BSA molecule) and could rapidly reach binding equilibrium within 5 min. Moreover, the adsorption of BSA was found to be remarkably dependent on the pH and salt concentration of the protein solutions, and the bound protein could be quantitatively desorbed by washing with a medium with lowered pH or raised salt concentration. PMID:25594881

  10. Removal of fluoride from groundwater by adsorption onto La(III)- Al(III) loaded scoria adsorbent

    NASA Astrophysics Data System (ADS)

    Zhang, Shengyu; Lu, Ying; Lin, Xueyu; Su, Xiaosi; Zhang, Yuling

    2014-06-01

    The La3+-Al3+ loaded scoria (La-Al-Scoria) was prepared as adsorbent for the fluoride removal from groundwater. The connecting time experiment indicated that the fluoride adsorption process reached equilibrium within 5 hours. The kinetics of fluoride ion adsorption onto La-Al-Scoria was followed the pseudo-second order with correlation coefficient value (R2) of 0.997. The isotherm data was well fitted to both of the Freundlich and Langmuir isotherm models, the R2 of Freundlich and Langmuir were 0.98 and 0.97, respectively. Subsequently, the adsorbent was characterized by scanning electron microscope (SEM), Energy dispersive analysis of X-ray (EDX), X-ray diffraction analysis (XRD) and X-ray Photoelectron Spectroscopy (XPS) measurements. SEM visual expressed that the dense canal surface structure of natural scoria appeared a large amount of rod-like composite after modification. The XRD and XPS instrumental studies revealed that the La3+ and Al3+ were loaded on the surface of modified scoria and the fluoride ion was adsorbed on the La-Al-Scoria. The large amount of La-Al-O composite oxide existed onto the surface of La-Al-Scoria was the immanent cause for the excellent adsorption capacity of fluoride ion.

  11. ARSENIC TREATMENT BY ADSORPTIVE TECHNOLOGY

    EPA Science Inventory

    Presentation will discuss the removal of arsenic from drinking water using the adsorptive media treatment process. Fundamental information is provided on the design and operation of adsorptive media technology including the selection of the adsorptive media. The information cites...

  12. A Simple Adsorption Experiment

    ERIC Educational Resources Information Center

    Guirado, Gonzalo; Ayllon, Jose A.

    2011-01-01

    The study of adsorption phenomenon is one of the most relevant and traditional physical chemistry experiments performed by chemistry undergraduate students in laboratory courses. In this article, we describe an easy, inexpensive, and straightforward way to experimentally determine adsorption isotherms using pieces of filter paper as the adsorbent…

  13. Environmental Degradation, Disproportionality, and the Double Diversion: Reaching out, Reaching ahead, and Reaching beyond

    ERIC Educational Resources Information Center

    Freudenburg, William R.

    2006-01-01

    Rather than seeking ivory-tower isolation, members of the Rural Sociological Society have always been distinguished by a willingness to work with specialists from a broad range of disciplines, and to work on some of the world's most challenging problems. What is less commonly recognized is that the willingness to reach beyond disciplinary…

  14. Records Reaching Recording Data Technologies

    NASA Astrophysics Data System (ADS)

    Gresik, G. W. L.; Siebe, S.; Drewello, R.

    2013-07-01

    The goal of RECORDS (Reaching Recording Data Technologies) is the digital capturing of buildings and cultural heritage objects in hard-to-reach areas and the combination of data. It is achieved by using a modified crane from film industry, which is able to carry different measuring systems. The low-vibration measurement should be guaranteed by a gyroscopic controlled advice that has been , developed for the project. The data were achieved by using digital photography, UV-fluorescence photography, infrared reflectography, infrared thermography and shearography. Also a terrestrial 3D laser scanner and a light stripe topography scanner have been used The combination of the recorded data should ensure a complementary analysis of monuments and buildings.

  15. Neural Correlates of Reach Errors

    PubMed Central

    Hashambhoy, Yasmin; Rane, Tushar; Shadmehr, Reza

    2005-01-01

    Reach errors may be broadly classified into errors arising from unpredictable changes in target location, called target errors, and errors arising from miscalibration of internal models, called execution errors. Execution errors may be caused by miscalibration of dynamics (e.g.. when a force field alters limb dynamics) or by miscalibration of kinematics (e.g., when prisms alter visual feedback). While all types of errors lead to similar online corrections, we found that the motor system showed strong trial-by-trial adaptation in response to random execution errors but not in response to random target errors. We used fMRI and a compatible robot to study brain regions involved in processing each kind of error. Both kinematic and dynamic execution errors activated regions along the central and the post-central sulci and in lobules V, VI, and VIII of the cerebellum, making these areas possible sites of plastic changes in internal models for reaching. Only activity related to kinematic errors extended into parietal area 5. These results are inconsistent with the idea that kinematics and dynamics of reaching are computed in separate neural entities. In contrast, only target errors caused increased activity in the striatum and the posterior superior parietal lobule. The cerebellum and motor cortex were as strongly activated as with execution errors. These findings indicate a neural and behavioral dissociation between errors that lead to switching of behavioral goals, and errors that lead to adaptation of internal models of limb dynamics and kinematics. PMID:16251440

  16. Adsorption-desorption of 2,4,6-trinitrotoluene and hexahydro-1,3,5-trinitro-1,3,5-triazine in soils

    SciTech Connect

    Xue, S.K.; Selim, H.M.; Iskandar, I.K.

    1995-11-01

    This study studied the adsorption-desorption behavior of TNT (2, 4, 6-trinitrotoluene) and RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine) in a bentonite/sand reference material (Swy-1 montmorillonite clay mixed with acid-washed sand) and two selected soils (Norwood and Kolin). Release of TNT,RDX, and other compounds from a contaminated soil obtained from the Louisiana Army Ammunition Plant (AAP) site was also investigated. The kinetics of TNT and RDX retention were measured using batch methods for a range of input concentrations. For RDX, the adsorption isotherms were distinctly linear. The TNT adsorption isotherm for bentonite/sand mixture appeared linear and was described equally well using linear, Freundlich, Langmuir, and a modified Langmuir model. For the Norwood and Kolin soils, TNT adsorption isotherms exhibited distinct nonlinearity and the Freundlich model provided the best fit. As indicated by the K{sub d} values, TNT exhibited stronger retention or affinity to all soils and the bentonite/sand mixture than for RDX. The RDX retention data indicated little time-dependent behavior. The TNT retention data indicated a continued decrease in TNT concentration with time in the Norwood and Kolin soils. This was possibly caused by the formation and subsequent adsorption of transformation products because transformation products, such as amino nitro toluene compounds, were identified during batch experiments. For the bentonite/sand mixture, TNT retention was rapid initially and reached apparent equilibrium within 1 day. Unlike Kolin and Norwood soils, there was no hysteretic behavior of TNT adsorption-desorption by the bentonite/sand mixture and a mass balance suggested fully reversible retention mechanisms. 15 refs., 13 figs., 2 tabs.

  17. Adsorption and isothermal models of atrazine by zeolite prepared from Egyptian kaolin

    NASA Astrophysics Data System (ADS)

    Jamil, Tarek S.; Gad-Allah, Tarek A.; Ibrahim, Hanan S.; Saleh, Tamer S.

    2011-01-01

    The adsorption behavior of Atrazine on zeolites, prepared from Egyptian kaolin, has been studied in order to consider the application of these types of zeolites in water purification. The batch mode has been employed, using atrazine solution of concentration ranging from 2 to 10 mg /l. The adsorption capacity and distribution coefficients ( Kd) were determined for the adsorption system as a function of sorbate concentration. It was found that, under the studies concentrations, the percent of adsorbed atrazine on both zeolites match to Langmuir and Freundlich adsorption models. The constants of each model were calculated to assess the adsorption behavior of atrazine on each type of zeolite. According to the equilibrium studies, adsorption of atrazine on zeolite X at lower concentrations is much better than that on zeolite A. The application of Dublin-Kaganer-Radushkevich model revealed physisorption endothermic adsorption process for both zeolites. These results show that natural zeolites hold great potential to remove hazardous materials such as atrazine from water.

  18. Adsorption kinetics and thermodynamics of acid Bordeaux B from aqueous solution by graphene oxide/PAMAMs.

    PubMed

    Zhang, Fan; He, Shengfu; Zhang, Chen; Peng, Zhiyuan

    2015-01-01

    Graphene oxide/polyamidoamines dendrimers (GO/PAMAMs) composites were synthesized via modifying GO with 2.0 G PAMAM. The adsorption behavior of the GO/PAMAMs for acid Bordeaux B (ABB) was studied and the effects of media pH, adsorption time and initial ABB concentration on adsorption capacity of the adsorbent were investigated. The optimum pH value of the adsorption of ABB onto GO/PAMAMs was 2.5. The maximum adsorption capacity increased from 325.78 to 520.83 mg/g with the increase in temperature from 298 to 328 K. The equilibrium data followed the Langmuir isotherm model better than the Freundlich model. The kinetic study illustrated that the adsorption of ABB onto GO/PAMAMs fit the pseudo-second-order model. The thermodynamic parameters indicated that the adsorption process was physisorption, and also an endothermic and spontaneous process. PMID:26398038

  19. Enhanced adsorptive removal of toxic dyes using SiO2 nanofibers

    NASA Astrophysics Data System (ADS)

    Batool, S. S.; Imran, Z.; Hassan, Safia; Rasool, Kamran; Ahmad, Mushtaq; Rafiq, M. A.

    2016-05-01

    Electrospinning method was used to synthesize porous SiO2 nanofibers. The adsorption of Methyl Orange and Safranin O by porous SiO2 nanofibers was carried out by varying the parameters such as pH, contact time, adsorbent dose, dye concentration, and temperature. Equilibrium adsorption data followed Langmuir isotherms. Kinetic adsorption followed second-order rate kinetics model. The maximum adsorption capacity for Methyl Orange and Safranin O was found to be 730.9 mg/g and 960.4 mg/g, respectively. Acidic pH was favorable for the adsorption of Methyl Orange while basic pH was favorable for the adsorptions of Safranin O. Modeling study suggested the major mode of adsorption, while thermodynamic study showed the endothermic reactions. This effort has pronounced impact on environmental applications of SiO2 nanofibers as auspicious adsorbent nanofibers for organic material from aqueous solution.

  20. Adsorption of coliphages T1 and T7 to clay minerals.

    PubMed Central

    Schiffenbauer, M; Stotzky, G

    1982-01-01

    Coliphages T1 and T7 of Escherichia coli were absorbed by kaolinite (K) and montmorillonite (M). Maximum adsorption of T7 (96%) to M was greater than that of T1 (84%), but the adsorption of both coliphages to K was the same (99%). Positively charged sites (i.e., anion exchange sites) on the clays appeared to be primarily responsible for the adsorption of T1 to K but only partially responsible for the adsorption of T1 to M; equilibrium adsorption isotherms of T1 to K and M did not show a correlation between adsorption and the cation exchange capacity of the clays, and the reduction in adsorption caused by sodium metaphosphate (a polyanion that interacts with positively charged sites on clay) was more pronounced with K than with M. The equilibrium adsorption isotherms of T7 to K and M suggested a correlation between adsorption and the cation exchange capacity of the clays. However, studies with sodium metaphosphate indicated that T7 also adsorbed to positively charged sites on the clays, especially on K. Adsorption of the coliphages to positively charged sites was greater with K than with M, probably because the ratio of positively charged sites to negatively charged sites was greater on K than on M. PMID:7041821

  1. Adsorption of selenium by amorphous iron oxyhydroxide and manganese dioxide

    USGS Publications Warehouse

    Balistrieri, L.S.; Chao, T.T.

    1990-01-01

    is reflected in decreasing equilibrium constants for selenite with increasing adsorption density and both experimental observations and modeling results suggest that manganese dioxide has fewer sites of higher energy for selenite adsorption than amorphous iron oxyhydroxide. Modeling and interpreting the adsorption of phosphate, molybdate, and silicate on the oxides are made difficult by the lack of constraint in choosing surface species and the fact that equally good fits can be obtained with different surface species. Finally, predictions of anion competition using the model results from single adsorbate systems are not very successful because the model does not account for surface site heterogeneity. Selenite adsorption data from a multi-adsorbate system could be fit if the equilibrium constant for selenite is decreased with increasing anion adsorption density. ?? 1990.

  2. Adsorption of Ions at Uncharged Insoluble Monolayers.

    PubMed

    Peshkova, Tatyana V; Minkov, Ivan L; Tsekov, Roumen; Slavchov, Radomir I

    2016-09-01

    A method is proposed for the experimental determination of the adsorption of inorganic electrolytes at a surface covered with insoluble surfactant monolayer. This task is complicated by the fact that the change of the salt concentration alters both chemical potentials of the electrolyte and the surfactant. Our method resolves the question by combining data for the surface pressure versus area of the monolayer at several salt concentrations with data for the equilibrium spreading pressure of crystals of the surfactant (used to fix a standard state). We applied the method to alcohols spread at the surface of concentrated halide solutions. The measured salt adsorption is positive and has nonmonotonic dependence on the area per surfactant molecule. For the liquid expanded film, depending on the concentration, there is one couple of ions adsorbed per each 3-30 surfactant molecules. We analyzed which ion, the positive or the negative, stands closer to the surface, by measuring the effect of NaCl on the Volta potential of the monolayer. The potentiometric data suggest that Na(+) is specifically adsorbed, while Cl(-) remains in the diffuse layer, i.e., the surface is positively charged. The observed reverse Hofmeister series of the adsorptions of NaF, NaCl, and NaBr suggests the same conclusion holds for all these salts. The force that causes the adsorption of Na(+) seems to be the interaction of the ion with the dipole moment of the monolayer. PMID:27529571

  3. An Updated Equilibrium Machine

    NASA Astrophysics Data System (ADS)

    Schultz, Emeric

    2008-08-01

    A device that can demonstrate equilibrium, kinetic, and thermodynamic concepts is described. The device consists of a leaf blower attached to a plastic container divided into two chambers by a barrier of variable size and form. Styrofoam balls can be exchanged across the barrier when the leaf blower is turned on and various air pressures are applied. Equilibrium can be approached from different distributions of balls in the container under different conditions. The Le Châtelier principle can be demonstrated. Kinetic concepts can be demonstrated by changing the nature of the barrier, either changing the height or by having various sized holes in the barrier. Thermodynamic concepts can be demonstrated by taping over some or all of the openings and restricting air flow into container on either side of the barrier.

  4. Absolute Equilibrium Entropy

    NASA Technical Reports Server (NTRS)

    Shebalin, John V.

    1997-01-01

    The entropy associated with absolute equilibrium ensemble theories of ideal, homogeneous, fluid and magneto-fluid turbulence is discussed and the three-dimensional fluid case is examined in detail. A sigma-function is defined, whose minimum value with respect to global parameters is the entropy. A comparison is made between the use of global functions sigma and phase functions H (associated with the development of various H-theorems of ideal turbulence). It is shown that the two approaches are complimentary though conceptually different: H-theorems show that an isolated system tends to equilibrium while sigma-functions allow the demonstration that entropy never decreases when two previously isolated systems are combined. This provides a more complete picture of entropy in the statistical mechanics of ideal fluids.

  5. The equilibrium dayside magnetosphere

    NASA Technical Reports Server (NTRS)

    Zavriyev, Anton; Hasegawa, Akira

    1989-01-01

    A method is presented of computing the dayside global earth magnetic field which is in equilibrium with the plasma pressure, based on satellite observations at a local region of the magnetosphere. The method, which utilizes a perturbation around a dipole magnetic field, involves computation of the global plasma pressure profile based on the equatorial (anisotropic) pressure data, derivation of the current profile which satisfies the equilibrium condition, and computation of the magnetic field using the current profile and the boundary current produced by the solar wind. The method is applied for the Active Magnetospheric Particle Tracer Explorers data, and the result of the computation is found to compare reasonably well with the observed magnetic field profile near the geomagnetic equator.

  6. Solids Far from Equilibrium

    NASA Astrophysics Data System (ADS)

    Godrèche, C.

    2011-03-01

    Preface; 1. Shape and growth of crystals P. Nozières; 2. Instabilities of planar solidification fronts B. Caroli, C. Caroli and B. Roulet; 3. An introduction to the kinetics of first-order phase transition J. S. Langer; 4. Dendritic growth and related topics Y. Pomeau and M. Ben Amar; 5. Growth and aggregation far from equilibrium L. M. Sander; 6. Kinetic roughening of growing surfaces J. Krug and H. Spohn; Acknowledgements; References; Index.

  7. Exoplanet Equilibrium Chemistry Calculations

    NASA Astrophysics Data System (ADS)

    Blumenthal, Sarah; Harrington, J.; Bowman, M.; Blecic, J.

    2013-10-01

    Recently, Agundez et al. (2012, A&A 548, A73) used a chemical kinetics code to study a model HD 209458b (equilibrium temperature of 1450 K, assuming full redistribution and 0 albedo). They found that thermochemistry dominates most of the dayside, but that significant compositional gradients may exist across the dayside. We calculate equilibrium-chemistry molecular abundances for several model exoplanets, using NASA's open-source Chemical Equilibrium Abundances code (McBride and Gordon 1996). We vary the degree of radiation redistribution to the dark side, ranging from total redistribution to instantaneous reradiation. Atomically, both the solar abundance multiple and the carbon fraction vary. Planet substellar temperatures range from just above 1200 K, where photochemistry should no longer be important, to those of hot planets (3000 K). We present synthetic abundance images for the key spectroscopic molecules CO, CH4, and H2O for several hot-Jupiter model planets. This work was supported by the NASA Planetary Atmospheres grant NNX12AI69G.

  8. Equilibrium Electroconvective Instability

    NASA Astrophysics Data System (ADS)

    Rubinstein, I.; Zaltzman, B.

    2015-03-01

    Since its prediction 15 years ago, hydrodynamic instability in concentration polarization at a charge-selective interface has been attributed to nonequilibrium electro-osmosis related to the extended space charge which develops at the limiting current. This attribution had a double basis. On the one hand, it has been recognized that neither equilibrium electro-osmosis nor bulk electroconvection can yield instability for a perfectly charge-selective solid. On the other hand, it has been shown that nonequilibrium electro-osmosis can. The first theoretical studies in which electro-osmotic instability was predicted and analyzed employed the assumption of perfect charge selectivity for the sake of simplicity and so did the subsequent studies of various time-dependent and nonlinear features of electro-osmotic instability. In this Letter, we show that relaxing the assumption of perfect charge selectivity (tantamount to fixing the electrochemical potential of counterions in the solid) allows for the equilibrium electroconvective instability. In addition, we suggest a simple experimental test for determining the true, either equilibrium or nonequilibrium, origin of instability in concentration polarization.

  9. Mirror versus parallel bimanual reaching

    PubMed Central

    2013-01-01

    Background In spite of their importance to everyday function, tasks that require both hands to work together such as lifting and carrying large objects have not been well studied and the full potential of how new technology might facilitate recovery remains unknown. Methods To help identify the best modes for self-teleoperated bimanual training, we used an advanced haptic/graphic environment to compare several modes of practice. In a 2-by-2 study, we compared mirror vs. parallel reaching movements, and also compared veridical display to one that transforms the right hand’s cursor to the opposite side, reducing the area that the visual system has to monitor. Twenty healthy, right-handed subjects (5 in each group) practiced 200 movements. We hypothesized that parallel reaching movements would be the best performing, and attending to one visual area would reduce the task difficulty. Results The two-way comparison revealed that mirror movement times took an average 1.24 s longer to complete than parallel. Surprisingly, subjects’ movement times moving to one target (attending to one visual area) also took an average of 1.66 s longer than subjects moving to two targets. For both hands, there was also a significant interaction effect, revealing the lowest errors for parallel movements moving to two targets (p < 0.001). This was the only group that began and maintained low errors throughout training. Conclusion Combined with other evidence, these results suggest that the most intuitive reaching performance can be observed with parallel movements with a veridical display (moving to two separate targets). These results point to the expected levels of challenge for these bimanual training modes, which could be used to advise therapy choices in self-neurorehabilitation. PMID:23837908

  10. Adsorption study of Ammonia Nitrogen by watermelon rind

    NASA Astrophysics Data System (ADS)

    Ibrahim, A.; Yusof, L.; Beddu, N. S.; Galasin, N.; Lee, P. Y.; Lee, R. N. S.; Zahrim, A. Y.

    2016-06-01

    The utilization of fruit waste for low-cost adsorbents as a replacement for costly conventional methods of removing ammonia nitrogen from wastewater has been reviewed. The adsorption studies were conducted as a function of contact time and adsorbent dosage and it were carried out on four different adsorbents; fresh watermelon rind and modified watermelon rind with sodium hydroxide (NaOH), potassium hydroxide (KOH) and sulphuric acid (H2SO4). Adsorbents were tested for characterization by using zeta potential test and all samples shows negative values thus makes it favourable for the adsorption process. The batch experimental result showed that adsorption process is rapid and equilibrium was established within 40 minutes of contact time. The ammonia nitrogen removal rate amounted in range of 96% to 99%, and the adsorption capacities were in range of 1.21 to 1.24 mg/g for all four different types of adsorbents used.

  11. Adsorption and desorption of Zn, Cu, and Cr by sediments from the Raisi River (Michigan)

    SciTech Connect

    Young, T.C.; DePinto, J.V.; Kipp, T.W.

    1987-01-01

    Metal adsorption by Raisin River sediments in vitro depended linearly on soluble metal concentration to adsorption densities of 6,000-9,000 microg/g with 48 hr partition coefficients of approximately 50, 30, and 25 L/g for Cu, Cr, and Zn, respectively. Partition coefficients computed from field data spanned a comparatively wider range of values in a manner consistent with the often reported adsorbent concentration effect, but other factors likely contributed, too. Desorption of Zn was complete and rapid (24-48 hr) in contrast to Cr, which was incomplete and much slower; Cu desorption was intermediate to Zn and Cr. A reversible-resistant equilibrium model (DiToro et al. 1986) could not describe the observations as Cu and Cr had not reached metastable desorption equilibria after 24 days. Metal desorption, however, could be described kinetically by distributing sorbed cations between either of two classes; rapidly desorbing and slowly desorbing cations. Sequential and simultaneous desorption models gave similar predictions. Aqueous chemical considerations suggested precipitated as well as adsorbed species could give rise to the observations, but available data did not permit adequate tests of this hypothesis. The extent to which kinetic constraints rather than irreversible reactions account for the desorption-resistant binding signifies a potentially greater metal mobility or bioavailability than would otherwise be assumed.

  12. Impact of biochar produced from post-harvest residue on the adsorption behavior of diesel oil on loess soil.

    PubMed

    Jiang, Yu Feng; Sun, Hang; Yves, Uwamungu J; Li, Hong; Hu, Xue Fei

    2016-02-01

    The primary objective of this study was to investigate the effect of biochar, produced from wheat residue at different temperatures, on the adsorption of diesel oil by loess soil. Kinetic and equilibrium data were processed to understand the adsorption mechanism of diesel by biochar-affected loess soil; dynamic and thermodynamic adsorption experiments were conducted to characterize this adsorption. The surface features and chemical structure of biochar, modified at varying pyrolytic temperatures, were investigated using surface scanning electron microscopy and Fourier transform infrared analysis. The kinetic data showed that the adsorption of diesel oil onto loess soil could be described by a pseudo-second-order kinetic model, with the rate-controlling step being intraparticle diffusion. However, in the presence of biochar, boundary layer control and intraparticle diffusion were both involved in the adsorption. Besides, the adsorption equilibrium data were well described by the Freundlich isothermal model. The saturated adsorption capacity weakened as temperature increased, suggesting a spontaneous exothermic process. Thermodynamic parameter analysis showed that adsorption was mainly a physical process and was enhanced by chemical adsorption. The adsorption capacity of loess soil for diesel oil was weakened with increasing pH. The biochar produced by pyrolytic wheat residue increased the adsorption behavior of petroleum pollutants in loess soil. PMID:25980560

  13. A comparative adsorption study: 17β-estradiol onto aerobic granular sludge and activated sludge.

    PubMed

    Zheng, Xiao-ying; He, Yu-jie; Chen, Wei; Wang, Ming-yang; Cao, Su-lan; Ni, Ming; Chen, Yu

    2016-01-01

    Adsorption plays a significant role in removing hydrophobic 17β-estradiol (E2) from wastewater. Batch experiments were conducted to compare the adsorption of E2 onto activated aerobic granular sludge (AGS) and activated sludge (AS), and features evaluated included the adsorption kinetics, thermodynamics, and influence of other environmental factors. By using a non-chemical wet-heat technique, both AGS and AS were treated to inactivated status. Then, after loading E2, the adsorption equilibrium capacity of the AGS was found to be greater than that of the AS at the same initial concentration of E2. Moreover, both the adsorption processes corresponded to a pseudo-second-order kinetic model; the adsorption rate constant of AGS was found to be higher and the half-adsorption time was shorter than that of AS. Next, evaluations of adsorption isotherms and thermodynamics indicated that the adsorption process was mainly a physical process. Lower temperatures facilitated a higher equilibrium adsorption capacity. However, the adsorption binding sites of AGS were distributed more uniformly at higher temperature, in contrast to the distribution found for AS. Finally, acidic conditions and an appropriate ionic strength (0.4 mol/L) were found to be particularly conducive to the adsorption process. Overall, the results showed that AGS has the potential to adsorb E2 with significant efficiency, thereby offering a new and more efficient means of treating E2 and trace oestrogens in wastewater. PMID:26209151

  14. Adsorption of alkenyl succinic anhydride from solutions in carbon tetrachloride on a fine magnetite surface

    NASA Astrophysics Data System (ADS)

    Balmasova, O. V.; Ramazanova, A. G.; Korolev, V. V.

    2016-06-01

    The adsorption of alkenyl succinic anhydride from a solution in carbon tetrachloride on a fine magnetite surface at a temperature of 298.15 K is studied using fine magnetite, which forms the basis of magnetic fluids, as the adsorbent. An adsorption isotherm is recorded and interpreted in terms of the theory of the volume filling of micropores (TVFM). Adsorption process parameters are calculated on the basis of the isotherm. It is shown that at low equilibrium concentrations, the experimental adsorption isotherm is linear in the TVFM equation coordinates.

  15. Studies on Thorium Adsorption Characteristics upon Activated Titanium Hydroxide Prepared from Rosetta Ilmenite Concentrate

    SciTech Connect

    Gado, M Zaki, S

    2016-01-01

    The titanium hydroxide prepared from Rosetta ilmenite concentrate has been applied for Th (IV) adsorption from its acid aqueous solutions. The prepared hydroxide is first characterized by both Fourier transform infrared (FT-IR) spectrum and thermogravimetric analysis. The relevant factors affecting the adsorption process have been studied. The obtained equilibrium data fits well with the Langmuir isotherm rather than Freundlich isotherm, while the adsorption kinetic data follow the pseudo-second order model. The different thermodynamic parameters have also been calculated and indicate that the adsorption process is spontaneous.

  16. Adsorption-Desorption Kinetics of Soft Particles

    NASA Astrophysics Data System (ADS)

    Osberg, Brendan; Nuebler, Johannes; Gerland, Ulrich

    2015-08-01

    Adsorption-desorption processes are ubiquitous in physics, chemistry, and biology. Models usually assume hard particles, but within the realm of soft matter physics the adsorbing particles are compressible. A minimal 1D model reveals that softness fundamentally changes the kinetics: Below the desorption time scale, a logarithmic increase of the particle density replaces the usual Rényi jamming plateau, and the subsequent relaxation to equilibrium can be nonmonotonic and much faster than for hard particles. These effects will impact the kinetics of self-assembly and reaction-diffusion processes.

  17. Effect of structure-directing agents on facile hydrothermal preparation of hierarchical γ-Al2O3 and their adsorption performance toward Cr(VI) and CO2.

    PubMed

    Ge, Jinrong; Deng, Kejian; Cai, Weiquan; Yu, Jiaguo; Liu, Xiaoqin; Zhou, Jiabin

    2013-07-01

    Hierarchical flower-like and sphere-like mesoporous γ-Al2O3 microparticles were successfully prepared by a facile hydrothermal method followed by a calcination process using sodium aluminate as aluminum source, urea as precipitating agent, and Pluronic F127 (EO106PO70EO106), polyacrylic acid sodium (PAAS), and mixed F127-PAAS as structure-directing agents (SDAs), respectively. Effects of the SDAs on the phase structure, morphology, textural properties, surface alkaline, and the adsorption performance toward Cr(VI) and CO2 of the as-prepared samples were comparatively studied by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), N2 adsorption-desorption, CO2 temperature programmed desorption (CO2-TPD), and UV-Vis spectrophotometric method. The results indicate that the sphere-like γ-Al2O3 obtained by using F127 as the SDA shows the best adsorption performance toward Cr(VI) with a high adsorption rate of 95% and adsorption capacity of 5.7 mg/g when the adsorption reaches equilibrium for 4h at room temperature. However, the flower-like γ-Al2O3 obtained by using PAAS as the SDA has the biggest CO2 adsorption capacity of 1.04 mmol/g at room temperature. This work provides a simple and practical way to prepare potentially bifunctional γ-Al2O3 adsorbent for the removal of pollutants in water and air treatment from cheap sodium aluminate by using different SDAs. PMID:23623408

  18. Thermo-chemical dynamics and chemical quasi-equilibrium of plasmas in thermal non-equilibrium

    SciTech Connect

    Massot, Marc; Graille, Benjamin; Magin, Thierry E.

    2011-05-20

    We examine both processes of ionization by electron and heavy-particle impact in spatially uniform plasmas at rest in the absence of external forces. A singular perturbation analysis is used to study the following physical scenario, in which thermal relaxation becomes much slower than chemical reactions. First, electron-impact ionization is investigated. The dynamics of the system rapidly becomes close to a slow dynamics manifold that allows for defining a unique chemical quasi-equilibrium for two-temperature plasmas and proving that the second law of thermodynamics is satisfied. Then, all ionization reactions are taken into account simultaneously, leading to a surprising conclusion: the inner layer for short time scale (or time boundary layer) directly leads to thermal equilibrium. Global thermo-chemical equilibrium is reached within a short time scale, involving only chemical reactions, even if thermal relaxation through elastic collisions is assumed to be slow.

  19. The Equilibrium Spreading Tension of Pulmonary Surfactant.

    PubMed

    Dagan, Maayan P; Hall, Stephen B

    2015-12-01

    Monomolecular films at an air/water interface coexist at the equilibrium spreading tension (γ(e)) with the bulk phase from which they form. For individual phospholipids, γ(e) is single-valued, and separates conditions at which hydrated vesicles adsorb from tensions at which overcompressed monolayers collapse. With pulmonary surfactant, isotherms show that monolayers compressed on the surface of bubbles coexist with the three-dimensional collapsed phase over a range of surface tensions. γ(e) therefore represents a range rather than a single value of surface tension. Between the upper and lower ends of this range, rates of collapse for spread and adsorbed films decrease substantially. Changes during adsorption across this narrow region of coexistence between the two- and three-dimensional structures at least partially explain how alveolar films of pulmonary surfactant become resistant to collapse. PMID:26583569

  20. Structural design using equilibrium programming

    NASA Technical Reports Server (NTRS)

    Scotti, Stephen J.

    1992-01-01

    Multiple nonlinear programming methods are combined in the method of equilibrium programming. Equilibrium programming theory has been appied to problems in operations research, and in the present study it is investigated as a framework to solve structural design problems. Several existing formal methods for structural optimization are shown to actually be equilibrium programming methods. Additionally, the equilibrium programming framework is utilized to develop a new structural design method. Selected computational results are presented to demonstrate the methods.

  1. Effect of Grain Size on Uranium(VI) Surface Complexation Kinetics and Adsorption Additivity

    SciTech Connect

    Shang, Jianying; Liu, Chongxuan; Wang, Zheming; Zachara, John M.

    2011-07-27

    Laboratory experiments were performed to investigate the contribution of variable grain sizes to uranium adsorption/desorption in a sediment collected from the US DOE Hanford site. The sediment was wet-sieved into four size fractions: coarse sand (1-2 mm), medium sand (0.2-1 mm), fine sand (0.05-0.2 mm), and clay/silt fraction (< 0.05mm). For each size fraction and their composite (sediment), batch experiments were performed to determine uranium adsorption isotherms, and stirred flow-cell experiments were conducted to derive kinetic data of uranium adsorption and subsequent desorption. The results showed that uranium adsorption isotherms and adsorption/desorption kinetics were size-specific, reflecting the effects of size-specific adsorption site concentration and kinetic rate constants. The larger-size fraction had a larger mass percentage in the sediment, but with a smaller adsorption site concentration and generally a slower uranium adsorption/desorption rate. The same equilibrium surface complexation reaction and reaction constant could describe uranium adsorption isotherms for all size fractions and the composite after accounting for the effect of adsorption site concentration. Mass-weighted, linear additivity was observed for both uranium adsorption isotherms and adsorption/desorption kinetics in the composite. Our analysis also showed that uranium adsorption site concentration estimated from the adsorption isotherms was 3 orders of magnitude less than a site concentration estimated from sediment surface area and generic site density. One important implication of this study is that grain size distribution may be used to estimate uranium adsorption site, and adsorption/desorption kinetic rates in heterogeneous sediments from a common location.

  2. Kinetics and isotherms of Neutral Red adsorption on peanut husk.

    PubMed

    Han, Runping; Han, Pan; Cai, Zhaohui; Zhao, Zhenhui; Tang, Mingsheng

    2008-01-01

    Adsorption of Neutral Red (NR) onto peanut husk in aqueous solutions was investigated at 295 K. Experiments were carried out as function of pH, adsorbent dosage, contact time, and initial concentration. The equilibrium adsorption data were analyzed by Langmuir, Freundlich, Temkin, Dubinin-Radushkevich, and Toth isotherm models. The results indicated that the Toth and Langmuir models provided the best correlation of the experimental data. The adsorption capacity of peanut husk for the removal of NR was determined with the Langmuir and found to be 37.5 mg/g at 295 K. The adsorption kinetic data were modeled using the pseudo-first order, pseudo-second order, and intra-particle diffusion kinetic equations. It was seen that the pseudo-first order and pseudo-second order kinetic equations could describe the adsorption kinetics. The intraparticle diffusion model was also used to express the adsorption process at the two-step stage. It was implied that peanut husk may be suitable as adsorbent material for adsorption of NR from aqueous solutions. PMID:19143308

  3. Boronate affinity adsorption of RNA: possible role of conformational changes

    NASA Technical Reports Server (NTRS)

    Singh, N.; Willson, R. C.; Fox, G. E. (Principal Investigator)

    1999-01-01

    Batch equilibrium adsorption isotherm determination is used to characterize the adsorption of mixed yeast RNA on agarose-immobilized m-aminophenylboronic acid. It is shown that the affinity-enhancing influence of divalent cations depends strongly on the precise nature of the cation used, with barium being far more effective than the conventionally-used magnesium. This adsorption-promoting influence of barium is suggested to arise primarily from ionic influences on the structure and rigidity of the RNA molecule, as the adsorption of ribose-based small molecules is not similarly affected. The substitution of barium for the standard magnesium counterion does not greatly promote the adsorption of DNA, implying that the effect is specific to RNA and may be useful in boronate-based RNA separations. RNA adsorption isotherms exhibit sharp transitions as functions of temperature, and these transitions occur at different temperatures with Mg2+ and with Ba2+. Adsorption affinity and capacity were found to increase markedly at lower temperatures, suggestive of an enthalpically favored interaction process. The stoichiometric displacement parameter, Z, in Ba2+ buffer is three times the value in Mg2+ buffer, and is close to unity.

  4. Continuous water treatment by adsorption and electrochemical regeneration.

    PubMed

    Mohammed, F M; Roberts, E P L; Hill, A; Campen, A K; Brown, N W

    2011-05-01

    This study describes a process for water treatment by continuous adsorption and electrochemical regeneration using an air-lift reactor. The process is based on the adsorption of dissolved organic pollutants onto an adsorbent material (a graphite intercalation compound, Nyex(®)1000) and subsequent electrochemical regeneration of the adsorbent leading to oxidation of the adsorbed pollutant. Batch experiments were carried out to determine the adsorption kinetics and equilibrium isotherm for adsorption of a sample contaminant, the organic dye Acid Violet 17. The adsorbent circulation rate, the residence time distribution (RTD) of the reactor, and treatment by continuous adsorption and electrochemical regeneration were studied to investigate the process performance. The RTD behaviour could be approximated as a continuously stirred tank. It was found that greater than 98% removal could be achieved for continuous treatment by adsorption and electrochemical regeneration for feed concentrations of up to 300 mg L(-1). A steady state model has been developed for the process performance, assuming full regeneration of the adsorbent in the electrochemical cell. Experimental data and modelled predictions (using parameters for the adsorbent circulation rate, adsorption kinetics and isotherm obtained experimentally) of the dye removal achieved were found to be in good agreement. PMID:21511325

  5. Hybrid adsorptive membrane reactor

    DOEpatents

    Tsotsis, Theodore T.; Sahimi, Muhammad; Fayyaz-Najafi, Babak; Harale, Aadesh; Park, Byoung-Gi; Liu, Paul K. T.

    2011-03-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  6. Hybrid adsorptive membrane reactor

    NASA Technical Reports Server (NTRS)

    Tsotsis, Theodore T. (Inventor); Sahimi, Muhammad (Inventor); Fayyaz-Najafi, Babak (Inventor); Harale, Aadesh (Inventor); Park, Byoung-Gi (Inventor); Liu, Paul K. T. (Inventor)

    2011-01-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  7. The equilibrium of neural firing: A mathematical theory

    SciTech Connect

    Lan, Sizhong

    2014-12-15

    Inspired by statistical thermodynamics, we presume that neuron system has equilibrium condition with respect to neural firing. We show that, even with dynamically changeable neural connections, it is inevitable for neural firing to evolve to equilibrium. To study the dynamics between neural firing and neural connections, we propose an extended communication system where noisy channel has the tendency towards fixed point, implying that neural connections are always attracted into fixed points such that equilibrium can be reached. The extended communication system and its mathematics could be useful back in thermodynamics.

  8. Adsorption of azo dyes using peanut hull and orange peel: a comparative study.

    PubMed

    do Nascimento, Graziele Elisandra; Duarte, Marta Maria Menezes Bezerra; Campos, Natália Ferreira; da Rocha, Otidene Rossiter Sá; da Silva, Valdinete Lins

    2014-01-01

    This work proposes the use of agro-industrial wastes, specifically peanut hull (HP) and orange peel (OP), as adsorbents for dyes, such as Remazol Golden Yellow RNL-150% (RYG), Gray Reactive BF-2R (RG) and Reactive Turquoise Q-G125 (RT). Characterization by Brunauer-Emmett-Teller indicates that the adsorbents are mesoporous, with pHzpc values of 5.0 for HP and 4.0 for OP. Fourier transform-infrared spectroscopy identified carbonyl and sulphonic groups. The initial pH of the best-adsorbing solution of the three colours was 2.0. Increasing the concentration of the adsorbent promoted an increase in the percentage of removal until saturation of the adsorbent. In a factorial design, the largest value of q was obtained with 0.25 g of the adsorbent, with a particle size of < 0.4 mm and a stirring speed of 300 rpm. Such conditions were used in kinetic studies and studies of adsorption equilibrium. The evolution kinetics were rapid in the first few minutes, and after 180 min the system reached equilibrium. The kinetic model that best fit the experimental data to a 95% confidence level for the F test was the pseudo-second-order model for RYG/HP, RG/OP and RT/OP. There was no significant difference between the kinetic models as evaluated by the F test for RYG/OP, RG/HP and RT/HP. The experimental results indicated favourable dye adsorption characteristics for the adsorbents studied. The results of the F test showed that for RYG and RG, there was no significant difference between the two evaluated models. This study suggests that HP and OP are viable alternatives for the treatment of effluents containing RYG, RG and RT dyes. PMID:24701942

  9. Uranium removal from aqueous solution by coir pith: equilibrium and kinetic studies.

    PubMed

    Parab, Harshala; Joshi, Shreeram; Shenoy, Niyoti; Verma, Rakesh; Lali, Arvind; Sudersanan, M

    2005-07-01

    Basic aspects of uranium adsorption by coir pith have been investigated by batch equilibration. The influence of different experimental parameters such as final solution pH, adsorbent dosage, sorption time, temperature and various concentrations of uranium on uptake were evaluated. Maximum uranium adsorption was observed in the pH range 4.0-6.0. The Freundlich and Langmuir adsorption models were used for the mathematical description of the adsorption equilibrium. The equilibrium data fitted well to both the equilibrium models in the studied concentration range of uranium (200-800 mg/l) and temperatures (305-336 K). The coir pith exhibited the highest uptake capacity for uranium at 317 K, at the final solution pH value of 4.3 and at the initial uranium concentration of 800 mg/l. The kinetics of the adsorption process followed a second-order adsorption. The adsorbent used proved to be suitable for removal of uranium from aqueous solutions. 0.2 N HCl was effective in uranium desorption. The results indicated that the naturally abundant coir pith of otherwise nuisance value exhibited considerable potential for application in removal of uranium from aqueous solution. PMID:15734311

  10. Adsorption of carbon dioxide, methane and nitrogen on an ultramicroporous copper metal-organic framework.

    PubMed

    Wu, Xiaofei; Yuan, Bin; Bao, Zongbi; Deng, Shuguang

    2014-09-15

    An ultramicroporous copper metal-organic framework (Cu-MOF), Cu(hfipbb)(H2hfipbb)0.5 [H2hfipbb=4,4'-(hexafluoro-isopropylidene) bis(benzoic acid)] was successfully synthesized by a microwave-assisted method (1) with a shorter reaction time and higher MOFs yield. The obtained Cu-MOF sample was characterized with scanning electron microscopy for crystal structure, powder X-ray diffraction for phase structure, and carbon dioxide adsorption at 273 K for pore textural properties. Single-component adsorption (adsorption equilibrium and kinetics) of CO2, CH4, and N2 on 1 was measured using a Micromeritics ASAP 2020 adsorption porosimeter at 278, 298 and 318 K, and pressures up to 1 bar. Isosteric heats of adsorption, Henry's constants, and diffusion time constants were calculated and carefully analyzed. Adsorption equilibrium selectivity (α), adsorbent selection parameter for pressure swing adsorption processes (S), kinetic selectivity and combined separation selectivity (β) for CO2/CH4, CO2/N2 and CH4/N2 binary mixtures were estimated based on the single-component adsorption data. The relative high values of the adsorption selectivities suggest that Cu-MOF is a promising adsorbent for separating CO2/CH4, CO2/N2 and CH4/N2 gas pairs. PMID:24998057

  11. Adsorption of a cationic surfactant by a magsorbent based on magnetic alginate beads.

    PubMed

    Obeid, Layaly; El Kolli, Nadia; Dali, Noëlle; Talbot, Delphine; Abramson, Sébastien; Welschbillig, Mathias; Cabuil, Valérie; Bée, Agnès

    2014-10-15

    Adsorption of cetylpyridinium chloride (CPC), a cationic surfactant, by magnetic alginate beads (MagAlgbeads) was investigated. The magnetic adsorbent (called magsorbent) was prepared by encapsulation of magnetic functionalized nanoparticles in an alginate gel. The influence on CPC adsorption of several parameters such as contact time, pH and initial surfactant concentration was studied. The equilibrium isotherm shows that adsorption occurs through both electrostatic interactions with charge neutralization of the carboxylate groups of the beads and hydrophobic interactions inducing the formation of surfactant aggregates in the beads. The dosage of calcium ions released in the solution turns out to be a useful tool for understanding the adsorption mechanisms. Adsorption is accompanied by a shrinking of the beads that corresponds to a 45% reduction of the volume. Adsorption kinetic experiments show that equilibrium time is strongly dependent on the surfactant concentration, which monitors the nature of the interactions. On the other hand, since the pH affects the ionization state of adsorption sites, adsorption depends on the pH solution, maximum adsorption being obtained in a large pH range (3.2-12) in agreement with the pKa value of alginate (pKa=3.4-4.2). Finally, due to the formation of micelle-like surfactants aggregates in the magnetic alginate beads, they could be used as a new efficient magsorbent for hydrophobic pollutants. PMID:25086393

  12. Adsorption Model for Off-Gas Separation

    SciTech Connect

    Veronica J. Rutledge

    2011-03-01

    The absence of industrial scale nuclear fuel reprocessing in the U.S. has precluded the necessary driver for developing the advanced simulation capability now prevalent in so many other countries. Thus, it is essential to model complex series of unit operations to simulate, understand, and predict inherent transient behavior and feedback loops. A capability of accurately simulating the dynamic behavior of advanced fuel cycle separation processes will provide substantial cost savings and many technical benefits. The specific fuel cycle separation process discussed in this report is the off-gas treatment system. The off-gas separation consists of a series of scrubbers and adsorption beds to capture constituents of interest. Dynamic models are being developed to simulate each unit operation involved so each unit operation can be used as a stand-alone model and in series with multiple others. Currently, an adsorption model has been developed in gPROMS software. Inputs include gas stream constituents, sorbent, and column properties, equilibrium and kinetic data, and inlet conditions. It models dispersed plug flow in a packed bed under non-isothermal and non-isobaric conditions for a multiple component gas stream. The simulation outputs component concentrations along the column length as a function of time from which the breakthrough data is obtained. It also outputs temperature along the column length as a function of time and pressure drop along the column length. Experimental data will be input into the adsorption model to develop a model specific for iodine adsorption on silver mordenite as well as model(s) specific for krypton and xenon adsorption. The model will be validated with experimental breakthrough curves. Another future off-gas modeling goal is to develop a model for the unit operation absorption. The off-gas models will be made available via the server or web for evaluation by customers.

  13. Effect of organic matter and calcium carbonate on behaviors of cadmium adsorption-desorption on/from purple paddy soils.

    PubMed

    Zhao, Xiulan; Jiang, Tao; Du, Bin

    2014-03-01

    Batch experiments and sequential extraction analysis were employed to investigate the effects of soil organic matter and CaCO3 on the adsorption and desorption of cadmium (Cd(2+)) onto and from two purple paddy soils, an acidic purple paddy soil (APPS) and a calcareous purple paddy soil (CPPS). The Cd(2+) adsorption isotherms on both soils could be well-described by the Langmuir and Freundlich equations. CPPS had a higher capacity and a stronger affinity for Cd(2+) adsorption compared with APPS. The adsorption process of Cd(2+) on APPS was dominated by electrostatic attractions, whereas the adsorption mechanism varied depending on the Cd(2+) concentrations in equilibrium solutions on CPPS. At low equilibrium concentrations, the adsorption process was primarily specific adsorption, but nonspecific adsorption dominated at high equilibrium concentrations. Removal of organic matter decreased the amount of Cd(2+) adsorption on both of the soils, slightly affected the Cd(2+) desorption rate and exchangeable Cd (EXC-Cd) in APPS and increased the desorption rate and EXC-Cd in CPPS, suggesting that the effect of organic matter on Cd(2+) adsorption-desorption depends on the soils. CPPS and APPS containing CaCO3 exhibited higher adsorption amounts but lower desorption rates and lower proportions of EXC-Cd than those of their corresponding soils without CaCO3, demonstrating that CaCO3 played an important role in Cd(2+) specific adsorption on soil. The changes in the thermodynamic parameters, including free energy (ΔG(0)), enthalpy (ΔH(0)) and entropy (ΔS(0)), as evaluated by the Van't Hoff equations, indicated that the adsorption was a spontaneous and endothermic process with the primary interaction forces of dipole interactions and hydrogen bonds on APPS, whereas both physical and chemical interactions dominated the adsorption on CPPS. PMID:24289979

  14. Non-equilibrium DMFT - Polaritonics

    NASA Astrophysics Data System (ADS)

    Lubatsch, Andreas; Frank, Regine

    Non-equilibrium physics recently really becomes important with the progress of ultrafast laser sciences. However in our understanding there is still a gap between equilibrium physics and the non-equilibrium, even though numerical methods have been advanced in recent years. We compare in this talk novel results at hand with equilibrium physics. The comparison will show that especially theoretical efforts are needed to explain many - so far - unresolved problems and to predict novel research on the basis of ab initio computing. We specifically discuss several non-equilibrium extensions of DMFT, numerical methods as well as semi-analytical solvers.

  15. Thermal equilibrium of goats.

    PubMed

    Maia, Alex S C; Nascimento, Sheila T; Nascimento, Carolina C N; Gebremedhin, Kifle G

    2016-05-01

    The effects of air temperature and relative humidity on thermal equilibrium of goats in a tropical region was evaluated. Nine non-pregnant Anglo Nubian nanny goats were used in the study. An indirect calorimeter was designed and developed to measure oxygen consumption, carbon dioxide production, methane production and water vapour pressure of the air exhaled from goats. Physiological parameters: rectal temperature, skin temperature, hair-coat temperature, expired air temperature and respiratory rate and volume as well as environmental parameters: air temperature, relative humidity and mean radiant temperature were measured. The results show that respiratory and volume rates and latent heat loss did not change significantly for air temperature between 22 and 26°C. In this temperature range, metabolic heat was lost mainly by convection and long-wave radiation. For temperature greater than 30°C, the goats maintained thermal equilibrium mainly by evaporative heat loss. At the higher air temperature, the respiratory and ventilation rates as well as body temperatures were significantly elevated. It can be concluded that for Anglo Nubian goats, the upper limit of air temperature for comfort is around 26°C when the goats are protected from direct solar radiation. PMID:27157333

  16. Lattice Boltzmann simulation of gas-solid adsorption processes at pore scale level

    NASA Astrophysics Data System (ADS)

    Zhou, L.; Qu, Z. G.; Chen, L.; Tao, W. Q.

    2015-11-01

    A two-dimensional lattice Boltzmann (LB) approach was established to implement kinetic concentration boundary conditions in interfacial mass-transfer processes and to simulate the adsorption process in porous media at pore scale and mesoscopic levels. A general treatment was applied to conduct three types of concentration boundary conditions effectively and accurately. Applicability for adsorption was verified by two benchmark examples, which were representative of the interparticle mass transport and intraparticle mass transport in the adsorption system, respectively. The gas-solid adsorption process in reconstructed porous media at the pore scale level was numerically investigated. Mass-transfer processes of the adsorption reaction were simulated by executing Langmuir adsorption kinetics on surfaces of adsorbent particles. Meanwhile, the homogeneous solid diffusion model (HSDM) was used for mass transport in interior particles. The transient adsorbed amount was obtained in detail, and the impact of flow condition, porosity, and adsorbent particle size on the entire dynamic adsorption performance was investigated. The time needed to approach steady state decreased with increased fluid velocity. Transient adsorption capability and time consumption to equilibrium were nearly independent of porosity, whereas increasing pore size led to a moderating adsorption rate and more time was consumed to approach the saturation adsorption. Benefiting from the advantages of the LB method, both bulk and intraparticle mass transfer performances during adsorption can be obtained using the present pore scale approach. Thus, interparticle mass transfer and intraparticle mass transfer are the two primary segments, and intraparticle diffusion has the dominant role.

  17. Removal of ibuprofen, naproxen and carbamazepine in aqueous solution onto natural clay: equilibrium, kinetics, and thermodynamic study

    NASA Astrophysics Data System (ADS)

    Khazri, Hassen; Ghorbel-Abid, Ibtissem; Kalfat, Rafik; Trabelsi-Ayadi, Malika

    2016-04-01

    This study aimed to describe the adsorption of three pharmaceuticals compounds (ibuprofen, naproxen and carbamazepine) onto natural clay on the basis of equilibrium parameters such as a function of time, effect of pH, varying of the concentration and the temperature. Adsorption kinetic data were modeled using the Lagergren's first-order and the pseudo-second-order kinetic equations. The kinetic results of adsorption are described better using the pseudo-second order model. The isotherm results were tested in the Langmuir, Freundlich and Dubinin-Radushkevich models. The thermodynamic parameters obtained indicate that the adsorption of pharmaceuticals on the clay is a spontaneous and endothermic process.

  18. Metasurface holograms reaching 80% efficiency

    NASA Astrophysics Data System (ADS)

    Zheng, Guoxing; Mühlenbernd, Holger; Kenney, Mitchell; Li, Guixin; Zentgraf, Thomas; Zhang, Shuang

    2015-05-01

    Surfaces covered by ultrathin plasmonic structures—so-called metasurfaces—have recently been shown to be capable of completely controlling the phase of light, representing a new paradigm for the design of innovative optical elements such as ultrathin flat lenses, directional couplers for surface plasmon polaritons and wave plate vortex beam generation. Among the various types of metasurfaces, geometric metasurfaces, which consist of an array of plasmonic nanorods with spatially varying orientations, have shown superior phase control due to the geometric nature of their phase profile. Metasurfaces have recently been used to make computer-generated holograms, but the hologram efficiency remained too low at visible wavelengths for practical purposes. Here, we report the design and realization of a geometric metasurface hologram reaching diffraction efficiencies of 80% at 825 nm and a broad bandwidth between 630 nm and 1,050 nm. The 16-level-phase computer-generated hologram demonstrated here combines the advantages of a geometric metasurface for the superior control of the phase profile and of reflectarrays for achieving high polarization conversion efficiency. Specifically, the design of the hologram integrates a ground metal plane with a geometric metasurface that enhances the conversion efficiency between the two circular polarization states, leading to high diffraction efficiency without complicating the fabrication process. Because of these advantages, our strategy could be viable for various practical holographic applications.

  19. Metasurface holograms reaching 80% efficiency.

    PubMed

    Zheng, Guoxing; Mühlenbernd, Holger; Kenney, Mitchell; Li, Guixin; Zentgraf, Thomas; Zhang, Shuang

    2015-04-01

    Surfaces covered by ultrathin plasmonic structures--so-called metasurfaces--have recently been shown to be capable of completely controlling the phase of light, representing a new paradigm for the design of innovative optical elements such as ultrathin flat lenses, directional couplers for surface plasmon polaritons and wave plate vortex beam generation. Among the various types of metasurfaces, geometric metasurfaces, which consist of an array of plasmonic nanorods with spatially varying orientations, have shown superior phase control due to the geometric nature of their phase profile. Metasurfaces have recently been used to make computer-generated holograms, but the hologram efficiency remained too low at visible wavelengths for practical purposes. Here, we report the design and realization of a geometric metasurface hologram reaching diffraction efficiencies of 80% at 825 nm and a broad bandwidth between 630 nm and 1,050 nm. The 16-level-phase computer-generated hologram demonstrated here combines the advantages of a geometric metasurface for the superior control of the phase profile and of reflectarrays for achieving high polarization conversion efficiency. Specifically, the design of the hologram integrates a ground metal plane with a geometric metasurface that enhances the conversion efficiency between the two circular polarization states, leading to high diffraction efficiency without complicating the fabrication process. Because of these advantages, our strategy could be viable for various practical holographic applications. PMID:25705870

  20. Reaching for the red planet

    PubMed

    David, L

    1996-05-01

    The distant shores of Mars were reached by numerous U.S. and Russian spacecraft throughout the 1960s to mid 1970s. Nearly 20 years have passed since those successful missions which orbited and landed on the Martian surface. Two Soviet probes headed for the planet in July, 1988, but later failed. In August 1993, the U.S. Mars Observer suddenly went silent just three days before it was to enter orbit around the planet and was never heard from again. In late 1996, there will be renewed activity on the launch pads with three probes departing for the red planet: 1) The U.S. Mars Global Surveyor will be launched in November on a Delta II rocket and will orbit the planet for global mapping purposes; 2) Russia's Mars '96 mission, scheduled to fly in November on a Proton launcher, consists of an orbiter, two small stations which will land on the Martian surface, and two penetrators that will plow into the terrain; and finally, 3) a U.S. Discovery-class spacecraft, the Mars Pathfinder, has a December launch date atop a Delta II booster. The mission features a lander and a microrover that will travel short distances over Martian territory. These missions usher in a new phase of Mars exploration, setting the stage for an unprecedented volley of spacecraft that will orbit around, land on, drive across, and perhaps fly at low altitudes over the planet. PMID:11538726

  1. Particle concentration effect: adsorption of divalent metal ions on coffee grounds.

    PubMed

    Utomo, Handojo Djati; Hunter, Keith A

    2010-03-01

    The adsorption of divalent metal ions Cu2+, Pb2+, Zn2+, and Cd2+ on coffee grounds as a function of coffee grounds concentration was studied in which adsorption density decreased as the concentration of coffee grounds (C(s)) increased. Adsorption studies were conducted by equilibrating aqueous solutions of each metal ion at concentrations in the range 19-291 micromol L(-1) with coffee suspensions in the concentration range 0.971-8.738 g L(-1), with the initial pH adjusted to 5.0+/-0.1 using NaOH or HNO3. Metastable Equilibrium Adsorption theory did not adequately explain the adsorption phenomenon, except at low concentrations of coffee grounds and trace metal ions. Instead the results indicated that flocculation might reduce the surface availability thus reducing the adsorption density. The flocculation theory was confirmed after a further experiment adding dispersant sodium hexa-meta-phosphate (NaHMP) to the suspension. PMID:19660940

  2. Ethane adsorption on aggregates of dahlia-like nanohorns: experiments and computer simulations.

    PubMed

    Russell, Brice A; Migone, Aldo D; Petucci, Justin; Mercedes Calbi, M; Yudasaka, Masako; Iijima, Sumio

    2016-06-01

    This is a report on a study of the adsorption characteristics of ethane on aggregates of unopened dahlia-like carbon nanohorns. This sorbent presents two main groups of adsorption sites: the outside surface of individual nanohorns and deep, interstitial spaces between neighbouring nanohorns towards the interior of the aggregates. We have explored the equilibrium properties of the adsorbed ethane films by determining the adsorption isotherms and isosteric heat of adsorption. Computer simulations performed on different model structures indicate that the majority of ethane adsorption occurs on the outer region of the aggregates, near the ends of the nanohorns. We have also measured the kinetics of adsorption of ethane on this sorbent. The measurements and simulations were conducted along several isotherms spanning the range between 120 K and 220 K. PMID:27218414

  3. Equilibrium of an elastically confined liquid drop

    NASA Astrophysics Data System (ADS)

    Kwon, Hyuk-Min; Kim, Ho-Young; Puëll, Jérôme; Mahadevan, L.

    2008-05-01

    When a liquid drop is confined between an elastic plate and a rigid substrate, it spreads spontaneously due to the effects of interfacial forces, eventually reaching an equilibrium shape determined by the balance between elastic and capillary effects. We provide an analytical theory for the static shape of the sheet and the extent of liquid spreading and show that our experiments are quantitatively consistent with the theory. The theory is relevant for the first step of painting when a brush is brought down on to canvas. More mundanely, it allows us to understand the stiction of microcantilevers to wafer substrates occurring in microelectromechanical fabrication processes.

  4. 2, 4 dichlorophenol (2, 4-DCP) sorption from aqueous solution using granular activated carbon and polymeric adsorbents and studies on effect of temperature on activated carbon adsorption.

    PubMed

    Ghatbandhe, A S; Yenkie, M K N

    2008-04-01

    Adsorption equilibrium, kinetics and thermodynamics of 2,4-dichlorophenol (2,4-DCP), one of the most commonly used chlorophenol, onto bituminous coal based Filtrasorb-400 grade granular activated carbon, were studied in aqueous solution in a batch system with respect to temperature. Uptake capacity of activated carbon found to increase with temperature. Langmuir isotherm models were applied to experimental equilibrium data of 2, 4-DCP adsorption and competitive studies with respect to XAD resin were carried out. Equilibrium data fitted very well to the Langmuir equilibrium model. Adsorbent monolayer capacity 'Q0, Langmuir constant 'b' and adsorption rate constant 'k(a)' were evaluated at different temperatures for activated carbon adsorption. This data was then used to calculate the energy of activation of adsorption and also the thermodynamic parameters, namely the free energy of adsorption, deltaG0, enthalpy of adsorption, deltaH0 and the entropy of adsorption deltaS0. The obtained results showed that the monolayer capacity increases with the increase in temperatures. The obtained values of thermodynamic parameters showed that adsorption of 2,4 DCP is an endothermic process. Synthetic resin was not found efficient to adsorb 2,4 DCP compared to activated carbon. The order of adsorption efficiencies of three resins used in the study found as XAD7HP > XAD4 > XAD1180. PMID:19295102

  5. Surface rheology of saponin adsorption layers.

    PubMed

    Stanimirova, R; Marinova, K; Tcholakova, S; Denkov, N D; Stoyanov, S; Pelan, E

    2011-10-18

    Extracts of the Quillaja saponaria tree contain natural surfactant molecules called saponins that very efficiently stabilize foams and emulsions. Therefore, such extracts are widely used in several technologies. In addition, saponins have demonstrated nontrivial bioactivity and are currently used as essential ingredients in vaccines, food supplements, and other health products. Previous preliminary studies showed that saponins have some peculiar surface properties, such as a very high surface modulus, that may have an important impact on the mechanisms of foam and emulsion stabilization. Here we present a detailed characterization of the main surface properties of highly purified aqueous extracts of Quillaja saponins. Surface tension isotherms showed that the purified Quillaja saponins behave as nonionic surfactants with a relatively high cmc (0.025 wt %). The saponin adsorption isotherm is described well by the Volmer equation, with an area per molecule of close to 1 nm(2). By comparing this area to the molecular dimensions, we deduce that the hydrophobic triterpenoid rings of the saponin molecules lie parallel to the air-water interface, with the hydrophilic glucoside tails protruding into the aqueous phase. Upon small deformation, the saponin adsorption layers exhibit a very high surface dilatational elasticity (280 ± 30 mN/m), a much lower shear elasticity (26 ± 15 mN/m), and a negligible true dilatational surface viscosity. The measured dilatational elasticity is in very good agreement with the theoretical predictions of the Volmer adsorption model (260 mN/m). The measured characteristic adsorption time of the saponin molecules is 4 to 5 orders of magnitude longer than that predicted theoretically for diffusion-controlled adsorption, which means that the saponin adsorption is barrier-controlled around and above the cmc. The perturbed saponin layers relax toward equilibrium in a complex manner, with several relaxation times, the longest of them being around 3

  6. Statistical physics ""Beyond equilibrium

    SciTech Connect

    Ecke, Robert E

    2009-01-01

    The scientific challenges of the 21st century will increasingly involve competing interactions, geometric frustration, spatial and temporal intrinsic inhomogeneity, nanoscale structures, and interactions spanning many scales. We will focus on a broad class of emerging problems that will require new tools in non-equilibrium statistical physics and that will find application in new material functionality, in predicting complex spatial dynamics, and in understanding novel states of matter. Our work will encompass materials under extreme conditions involving elastic/plastic deformation, competing interactions, intrinsic inhomogeneity, frustration in condensed matter systems, scaling phenomena in disordered materials from glasses to granular matter, quantum chemistry applied to nano-scale materials, soft-matter materials, and spatio-temporal properties of both ordinary and complex fluids.

  7. Thermodynamic analysis of adsorption refrigeration cycles

    SciTech Connect

    Saha, B.B.; Akisawa, Atsushi; Kashiwagi, Takao

    1997-12-31

    High- and mid-temperature waste heat can be recovered by using existing heat pump technologies. However, heat utilization near environmental temperatures still faces technical hurdles. Silica gel-water adsorption cycles have a distinct advantage over other systems in their ability to be driven by near-ambient temperature heat. Waste heat (above 60 C) can be exploited by using conventional silica gel-water adsorption chiller. The advanced silica gel-water adsorption chiller can operate effectively by utilizing low-grade waste heat ({approximately}50 C) as the driving source with a cooling source of 30 C. In this paper, the effect of operating temperatures on cycle performance is discussed from the thermodynamic viewpoint. The temperature effectiveness and the entropy generation number on cycle time are analyzed. For a comparatively short cycle time, adsorber/desorber heat exchanger temperature effectiveness reaches up to 92% after only 200 sec. The entropy generation number N{sub s} is defined by the ratio between irreversibility generated during a cycle and availability of the heat transfer fluid. The result showed that for the advanced adsorption cycle the entropy generation number N{sub s} is smaller for hot water temperature between 45 to 55 C with a cooling source of 30 C, while for the conventional cycle N{sub s} is smaller for hot water temperature between 65 to 75 C /with the same cooling source temperature.

  8. Fluorocarbon adsorption in hierarchical porous frameworks.

    PubMed

    Motkuri, Radha Kishan; Annapureddy, Harsha V R; Vijaykumar, M; Schaef, H Todd; Martin, Paul F; McGrail, B Peter; Dang, Liem X; Krishna, Rajamani; Thallapally, Praveen K

    2014-01-01

    Metal-organic frameworks comprise an important class of solid-state materials and have potential for many emerging applications such as energy storage, separation, catalysis and bio-medical. Here we report the adsorption behaviour of a series of fluorocarbon derivatives on a set of microporous and hierarchical mesoporous frameworks. The microporous frameworks show a saturation uptake capacity for dichlorodifluoromethane of >4 mmol g(-1) at a very low relative saturation pressure (P/Po) of 0.02. In contrast, the mesoporous framework shows an exceptionally high uptake capacity reaching >14 mmol g(-1) at P/Po of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption is found to generally correlate with the polarizability and boiling point of the refrigerant, with dichlorodifluoromethane > chlorodifluoromethane > chlorotrifluoromethane > tetrafluoromethane > methane. These results suggest the possibility of exploiting these sorbents for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling. PMID:25006832

  9. Fluorocarbon adsorption in hierarchical porous frameworks

    NASA Astrophysics Data System (ADS)

    Motkuri, Radha Kishan; Annapureddy, Harsha V. R.; Vijaykumar, M.; Schaef, H. Todd; Martin, Paul F.; McGrail, B. Peter; Dang, Liem X.; Krishna, Rajamani; Thallapally, Praveen K.

    2014-07-01

    Metal-organic frameworks comprise an important class of solid-state materials and have potential for many emerging applications such as energy storage, separation, catalysis and bio-medical. Here we report the adsorption behaviour of a series of fluorocarbon derivatives on a set of microporous and hierarchical mesoporous frameworks. The microporous frameworks show a saturation uptake capacity for dichlorodifluoromethane of >4 mmol g-1 at a very low relative saturation pressure (P/Po) of 0.02. In contrast, the mesoporous framework shows an exceptionally high uptake capacity reaching >14 mmol g-1 at P/Po of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption is found to generally correlate with the polarizability and boiling point of the refrigerant, with dichlorodifluoromethane >chlorodifluoromethane >chlorotrifluoromethane >tetrafluoromethane >methane. These results suggest the possibility of exploiting these sorbents for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling.

  10. Fluorocarbon adsorption in hierarchical porous frameworks

    SciTech Connect

    Motkuri, RK; Annapureddy, HVR; Vijaykumar, M; Schaef, HT; Martin, PF; McGrail, BP; Dang, LX; Krishna, R; Thallapally, PK

    2014-07-09

    Metal-organic frameworks comprise an important class of solid-state materials and have potential for many emerging applications such as energy storage, separation, catalysis and bio-medical. Here we report the adsorption behaviour of a series of fluorocarbon derivatives on a set of microporous and hierarchical mesoporous frameworks. The microporous frameworks show a saturation uptake capacity for dichlorodifluoromethane of >4 mmol g(-1) at a very low relative saturation pressure (P/P-o) of 0.02. In contrast, the mesoporous framework shows an exceptionally high uptake capacity reaching >14 mmol g(-1) at P/P-o of 0.4. Adsorption affinity in terms of mass loading and isosteric heats of adsorption is found to generally correlate with the polarizability and boiling point of the refrigerant, with dichlorodifluoromethane >chlorodifluoromethane >chlorotrifluoromethane >tetrafluoromethane >methane. These results suggest the possibility of exploiting these sorbents for separation of azeotropic mixtures of fluorocarbons and use in eco-friendly fluorocarbon-based adsorption cooling.

  11. The adsorption of plutonium IV and V on goethite

    NASA Astrophysics Data System (ADS)

    Sanchez, Arthur L.; Murray, James W.; Sibley, Thomas H.

    1985-11-01

    The adsorption of Pu(IV) and Pu(V) on goethite (αFeOOH) from NaNO 3 solution shows distinct differences related to the different hydrolytic character of these two oxidation states. Under similar solution conditions, the adsorption edge of the more strongly hydrolyzable Pu(IV) occurs in the pH range 3 to 5 while that for Pu(V) is at pH 5 to 7. The adsorption edge for Pu(V) shifts with time to lower pH values and this appears to be due to the reduction of Pu(V) to Pu(IV) in the presence of the goethite surface. These results suggest that redox transformations may be an important aspect of Pu adsorption chemistry and the resulting scavenging of Pu from natural waters. Increasing ionic strength (from 0.1 M to 3 M NaCl or NaNO 3 and 0.03 M to 0.3 M Na 2SO 4) did not influence Pu(IV) or Pu(V) adsorption. In the presence of dissolved organic carbon (DOC), Pu(V) reduction to Pu(IV) occurred in solution. Pu(IV) adsorption on goethite decreased by 30% in the presence of 240 ppm natural DOC found in Soap Lake, Washington waters. Increasing concentrations of carbonate ligands decreased Pu(IV) and Pu(V) adsorption on goethite, with an alkalinity of 1000 meq/l totally inhibiting adsorption. The Pu-goethite adsorption system provides the data base for developing a thermodynamic model of Pu interaction with an oxide surface and with dissolved ligands, using the MINEQL computer program. From the model calculations we determined equilibrium constants for the adsorption of Pu(IV) hydrolysis species. The model was then applied to Pu adsorption in carbonate media to see how the presence of CO 3-2 could influence the mobility of Pu. The decrease in adsorption appears to be due to formation of a Pu-CO 3 complex. Model calculations were used to predict what the adsorption curves would look like if Pu-CO 3 complexes formed.

  12. Adsorption of cadmium by biochar derived from municipal sewage sludge: Impact factors and adsorption mechanism.

    PubMed

    Chen, Tan; Zhou, Zeyu; Han, Rong; Meng, Ruihong; Wang, Hongtao; Lu, Wenjing

    2015-09-01

    Static equilibrium experiments were carried out to investigate the impact factors and the mechanism of cadmium adsorption on biochar derived from municipal sewage sludge. An appropriate dosage of biochar is sufficient; in the experiment, 0.2% is the optimal dosage for the largest removal capacity, while the removal capacity of biochar reduces with the increasing dosage. pH is another dominant factor of the adsorption process. The removal capacity of biochar is lower than 20 mg·g(-1) when the solution initial pH is lower than 2 pH units, comparatively retaining more than 40 mg·g(-1) at the solution initial pH higher than 3 pH units. Temperature has weak influence on the adsorptive performance. The main mechanism of the adsorption process of biochar for cadmium mainly involves (1) surface precipitation by forming insoluble cadmium compounds in alkaline condition, and (2) ion exchange for cadmium with exchangeable cations in the biochar, such as calcium ions. PMID:25966459

  13. [Study on treatment of methylene blue wastewater by fly ash adsorption-Fenton and thermal regeneration].

    PubMed

    Bai, Yu-Jie; Zhang, Ai-Li; Zhou, Ji-Ti

    2012-07-01

    The physicochemical properties of water-washed fly ash (FA) and acid modified fly ash (M-FA) were investigated. The adsorption of methylene blue by FA and M-FA were studied by batch experiments. Two methods, Fenton-drive oxidation regeneration and thermal regeneration, were used for regeneration of the used FA and M-FA. The result showed that the rate of adsorption process followed the second order kinetics and the adsorption followed Langmuir isotherms. The adsorption equilibrium time was 30 min, and the equilibrium adsorption capacity of FA and M-FA were 4.22 mg x g(-1) and 5.98 mg x g(-1) respectively. The adsorption capability of M-FA was higher than that of FA. In the range of pH 2-12, the adsorption capacity of M-FA increased with the increase of pH, whereas the adsorption capacity of FA decreased slowly until the pH 8 and then increased. Electrostatic adsorption was the major factor on the adsorption capacity. Around 61% and 55% percentage regeneration (PR) were obtained for FA and M-FA respectively when 78.4 mmol x L(-1) H2O2 and 0.72 mmol x L(-1) Fe2+ were used. When the condition of thermal regeneration was 400 degrees C and 2 h, a positive correlation can be found between the PRs of FA and regeneration times, the PRs were 102%, 104% and 107% in three cycles of adsorption-thermal regeneration process. However a negative correlation can be found between the PRs of M-FA and regeneration times, the PRs were 82%, 75% and 74% in three cycles of adsorption-thermal regeneration process. The PR of FA was higher than that of M-FA, and thermal regeneration was superior to Fenton-drive regeneration. PMID:23002621

  14. Adsorptive separation of propylene-propane mixtures

    SciTech Connect

    Jaervelin, H.; Fair, J.R. )

    1993-10-01

    The separation of propylene-propane mixtures is of great commercial importance and is carried out by fractional distillation. It is claimed to be the most energy-intensive distillation practiced in the United States. The purpose of this paper is to describe experimental work that suggests a practical alternative to distillation for separating the C[sub 3] hydrocarbons: adsorption. As studied, the process involves three adsorptive steps: initial separation with molecular sieves with heavy dilution with an inert gas; separation of propylene and propane separately from the inert gas, using activated carbon; and drying of the product streams with any of several available desiccants. The research information presented here deals with the initial step and includes both equilibrium and kinetic data. Isotherms are provided for propylene and propane adsorbed on three zeolites, activated alumina, silica gel, and coconut-based activated carbon. Breakthrough data are provided for both adsorption and regeneration steps for the zeolites, which were found to be superior to the other adsorbents for breakthrough separations. A flow diagram for the complete proposed process is included.

  15. Aqueous mercury adsorption by activated carbons.

    PubMed

    Hadi, Pejman; To, Ming-Ho; Hui, Chi-Wai; Lin, Carol Sze Ki; McKay, Gordon

    2015-04-15

    Due to serious public health threats resulting from mercury pollution and its rapid distribution in our food chain through the contamination of water bodies, stringent regulations have been enacted on mercury-laden wastewater discharge. Activated carbons have been widely used in the removal of mercuric ions from aqueous effluents. The surface and textural characteristics of activated carbons are the two decisive factors in their efficiency in mercury removal from wastewater. Herein, the structural properties and binding affinity of mercuric ions from effluents have been presented. Also, specific attention has been directed to the effect of sulfur-containing functional moieties on enhancing the mercury adsorption. It has been demonstrated that surface area, pore size, pore size distribution and surface functional groups should collectively be taken into consideration in designing the optimal mercury removal process. Moreover, the mercury adsorption mechanism has been addressed using equilibrium adsorption isotherm, thermodynamic and kinetic studies. Further recommendations have been proposed with the aim of increasing the mercury removal efficiency using carbon activation processes with lower energy input, while achieving similar or even higher efficiencies. PMID:25644627

  16. Chitosan/maghemite composite: a magsorbent for the adsorption of methyl orange.

    PubMed

    Obeid, Layaly; Bée, Agnès; Talbot, Delphine; Ben Jaafar, Soukeina; Dupuis, Vincent; Abramson, Sébastien; Cabuil, Valérie; Welschbillig, Mathias

    2013-11-15

    In this study, magnetic beads were prepared by encapsulation of magnetic nanoparticles in epichlorohydrin cross-linked chitosan beads. Their adsorption characteristics were assessed by using methyl orange (MO) as an adsorbate. MO adsorption onto chitosan beads was found to be optimal in the pH range of 3-5. The adsorption isotherm was well described by the Langmuir model and showed high MO adsorption capacity (2.38 mmol/g, i.e. 779 mg/g). MO adsorption kinetics followed a pseudo-second-order kinetic model, indicating that adsorption was the rate-limiting step. At 0.305 mmol/L, only 19 min was required to reach 90% adsorption and 50% of the MO was adsorbed in 2 min. Desorption studies of MO using NaOH showed the reusability of the magsorbent. No release of iron species was observed at pH>2.4. PMID:23998368

  17. Adsorptive removal of methylene blue by CuO-acid modified sepiolite as effective adsorbent and its regeneration with high-temperature gas stream.

    PubMed

    Su, Chengyuan; Wang, Liang; Chen, Menglin; Huang, Zhi; Lin, Xiangfeng

    2016-01-01

    In this study, the dynamic adsorption of methylene blue dye onto CuO-acid modified sepiolite was investigated. Meanwhile, the equilibrium and kinetic data of the adsorption process were studied to understand the adsorption mechanism. Furthermore, a high-temperature gas stream was applied to regenerate the adsorbent. The results showed that the Langmuir isotherm model was applied to describe the adsorption process. The positive value of enthalpy change indicated that the adsorption process was endothermic in nature. In the dynamic adsorption process, the best adsorption performance was achieved when the ratio of column height to diameter was 2.56 and the treatment capacity was 6 BV/h. The optimal scenario for regeneration experiments was the regeneration temperature of 550-650 °C, the space velocity of 100 min(-1) and the regeneration time of 10 min. The effective adsorption of CuO-acid modified sepiolite was kept for 12 cycles of adsorption and regeneration. PMID:27533859

  18. Ethanol adsorption on the Si (111) surface: First principles study

    NASA Astrophysics Data System (ADS)

    Gavrilenko, Alexander V.; Bonner, Carl E.; Gavrilenko, Vladimir I.

    2012-03-01

    Equilibrium atomic configurations and electron energy structure of ethanol adsorbed on the Si (111) surface are studied by the first principles density functional theory. Geometry optimization is performed by the total energy minimization method. Equilibrium atomic geometries of ethanol, both undissociated and dissociated, on the Si (111) surface are found and analysed. Reaction pathways and predicted transition states are discussed in comparison with available experimental data in terms of the feasibility of the reactions occurring. Analysis of atom and orbital resolved projected density of states indicates substantial modifications of the Si surface valence and conduction electron bands due to the adsorption of ethanol affecting the electronic properties of the surface.

  19. The Nash equilibrium: a perspective.

    PubMed

    Holt, Charles A; Roth, Alvin E

    2004-03-23

    In 1950, John Nash contributed a remarkable one-page PNAS article that defined and characterized a notion of equilibrium for n- person games. This notion, now called the "Nash equilibrium," has been widely applied and adapted in economics and other behavioral sciences. Indeed, game theory, with the Nash equilibrium as its centerpiece, is becoming the most prominent unifying theory of social science. In this perspective, we summarize the historical context and subsequent impact of Nash's contribution. PMID:15024100

  20. Grinding kinetics and equilibrium states

    NASA Technical Reports Server (NTRS)

    Opoczky, L.; Farnady, F.

    1984-01-01

    The temporary and permanent equilibrium occurring during the initial stage of cement grinding does not indicate the end of comminution, but rather an increased energy consumption during grinding. The constant dynamic equilibrium occurs after a long grinding period indicating the end of comminution for a given particle size. Grinding equilibrium curves can be constructed to show the stages of comminution and agglomeration for certain particle sizes.

  1. Protein adsorption on nanoparticles: model development using computer simulation.

    PubMed

    Shao, Qing; Hall, Carol K

    2016-10-19

    The adsorption of proteins on nanoparticles results in the formation of the protein corona, the composition of which determines how nanoparticles influence their biological surroundings. We seek to better understand corona formation by developing models that describe protein adsorption on nanoparticles using computer simulation results as data. Using a coarse-grained protein model, discontinuous molecular dynamics simulations are conducted to investigate the adsorption of two small proteins (Trp-cage and WW domain) on a model nanoparticle of diameter 10.0 nm at protein concentrations ranging from 0.5 to 5 mM. The resulting adsorption isotherms are well described by the Langmuir, Freundlich, Temkin and Kiselev models, but not by the Elovich, Fowler-Guggenheim and Hill-de Boer models. We also try to develop a generalized model that can describe protein adsorption equilibrium on nanoparticles of different diameters in terms of dimensionless size parameters. The simulation results for three proteins (Trp-cage, WW domain, and GB3) on four nanoparticles (diameter  =  5.0, 10.0, 15.0, and 20.0 nm) illustrate both the promise and the challenge associated with developing generalized models of protein adsorption on nanoparticles. PMID:27546610

  2. Enhanced adsorption of quaternary amine using modified activated carbon.

    PubMed

    Prahas, Devarly; Wang, M J; Ismadji, Suryadi; Liu, J C

    2014-01-01

    This study examined different methodologies to modify activated carbon (AC) for the removal of quaternary amine, tetramethylammonium hydroxide (TMAH), from water. Commercial carbon (WAC) was treated by nitric acid oxidation (NA-WAC), silica impregnation (SM-WAC0.5), and oxygen plasma (P10-WAC), and their characteristics and adsorption capacity were compared. The Langmuir model fitted the equilibrium adsorption data well under different pH. The maximum adsorption capacity of WAC was 27.77 mg/g, while those of NA-WAC, SM-WAC 0.5, and P10-WAC were 37.46, 32.83 and 29.03 mg/g, respectively. Nitric acid oxidation was the most effective method for enhancing the adsorption capacity of TMAH. Higher pH was favorable for TMAH adsorption. Desorption study revealed that NA-WAC had no considerable reduction in performance even after five cycles of regeneration by 0.1 N hydrochloric acid. It was proposed that electrostatic interaction was the main mechanism of TMAH adsorption on activated carbon. PMID:24845325

  3. A review of heavy metal adsorption by marine algae

    NASA Astrophysics Data System (ADS)

    Jin-Fen, Pan; Rong-Gen, Lin; Li, Ma

    2000-09-01

    Accumulation of heavy metals by algae had been studied extensively for biomonitoring or bioremediation purposes. Having the advantages of low cost raw material, big adsorbing capacity, no secondary pollution, etc., algae may be used to treat industrial water containing heavy metals. The adsorption processes were carried out in two steps: rapid physical adsorption first, and then slow chemical adsorption. pH is the major factor influencing the adsorption. The Freundlich equation fitted very well the adsorption isotherms. The uptake decreased with increasing ionic strength. The principal mechanism of metallic cation sequestration involves the formation of complexes between a metal ion and functional groups on the surface or inside the porous structure of the biological material. The carboxyl groups of alginate play a major role in the complexation. Different species of algae and the algae of the same species may have different adsorption capacity. Their selection affinity for heavy metals was the major criterion for the screening of a biologic adsorbent to be used in water treatment. The surface complex formation model (SCFM) can solve the equilibrium and kinetic problems in the biosorption.

  4. Adsorption Kinetics at Silica Gel/Ionic Liquid Solution Interface.

    PubMed

    Flieger, Jolanta; Tatarczak-Michalewska, Małgorzata; Groszek, Anna; Blicharska, Eliza; Kocjan, Ryszard

    2015-01-01

    A series of imidazolium and pyridinium ionic liquids with different anions (Cl(-), Br(-), BF₄(-), PF₆(-)) has been evaluated for their adsorption activity on silica gel. Quantification of the ionic liquids has been performed by the use of RP-HPLC with organic-aqueous eluents containing an acidic buffer and a chaotropic salt. Pseudo-second order kinetic models were applied to the experimental data in order to investigate the kinetics of the adsorption process. The experimental data showed good fitting with this model, confirmed by considerably high correlation coefficients. The adsorption kinetic parameters were determined and analyzed. The relative error between the calculated and experimental amount of ionic liquid adsorbed at equilibrium was within 7%. The effect of various factors such as initial ionic liquid concentration, temperature, kind of solvent, kind of ionic liquid anion and cation on adsorption efficiency were all examined in a lab-scale study. Consequently, silica gel showed better adsorptive characteristics for imidazolium-based ionic liquids with chaotropic anions from aqueous solutions in comparison to pyridinium ionic liquids. The adsorption was found to decrease with the addition of organic solvents (methanol, acetonitrile) but it was not sensitive to the change of temperature in the range of 5-40 °C. PMID:26690392

  5. Adsorption and desorption of uranium (VI) in aerated zone soil.

    PubMed

    Li, Xiaolong; Wu, Jiaojiao; Liao, Jiali; Zhang, Dong; Yang, Jijun; Feng, Yue; Zeng, Junhui; Wen, Wei; Yang, Yuanyou; Tang, Jun; Liu, Ning

    2013-01-01

    In this paper, the adsorption and desorption behavior of uranium (VI) in aerated zone soil (from Southwest China) was systematically investigated using a static experimental method in order to provide useful information for safety assessment of the disposal of (ultra-)low uraniferous radioactive waste, as well as a potential remediation method for uranium-contaminated soils. The adsorption behavior of uranium (VI) was firstly studied by batch experiments as functions of contact time, pH, liquid/solid ratio, temperature, colloids, minerals and coexistent ions. The results indicated that the adsorption of uranium (VI) by natural soil was efficient at an initial concentration of 10 mg/L uranium (VI) nitrate solution with 100 mg natural soil at room temperature when pH is about 7.0. The adsorption was strongly influenced by the solution pH, contact time, initial concentration and colloids. The adsorption equilibrium for uranium (VI) in soil was obtained within 24 h and the process could be described by the Langmuir adsorption equation. For uranium (VI) desorption, EDTA, citric acid and HNO(3) were evaluated under different conditions of temperature, concentration and proportion of liquid to solid. The adsorbed uranium (VI) on natural soil could be easily extracted by all these agents, especially by HNO(3), implying that the uranium-contaminated soils can be remedied by these reagents. PMID:22939949

  6. Adsorption of Methyl Tertiary Butyl Ether on Granular Zeolites: Batch and Column Studies

    PubMed Central

    Abu-Lail, Laila; Bergendahl, John A.; Thompson, Robert W.

    2010-01-01

    Methyl tertiary butyl ether (MTBE) has been shown to be readily removed from water with powdered zeolites, but the passage of water through fixed beds of very small powdered zeolites produces high friction losses not encountered in flow through larger sized granular materials. In this study, equilibrium and kinetic adsorption of MTBE onto granular zeolites, a coconut shell granular activated carbon (CS-1240), and a commercial carbon adsorbent (CCA) sample was evaluated. In addition, the effect of natural organic matter (NOM) on MTBE adsorption was evaluated. Batch adsorption experiments determined that ZSM-5 was the most effective granular zeolite for MTBE adsorption. Further equilibrium and kinetic experiments verified that granular ZSM-5 is superior to CS-1240 and CCA in removing MTBE from water. No competitive-adsorption effects between NOM and MTBE were observed for adsorption to granular ZSM-5 or CS-1240, however there was competition between NOM and MTBE for adsorption onto the CCA granules. Fixed-bed adsorption experiments for longer run times were performed using granular ZSM-5. The bed depth service time model (BDST) was used to analyze the breakthrough data. PMID:20153106

  7. Large scale purification of puerarin from Puerariae Lobatae Radix through resins adsorption and acid hydrolysis.

    PubMed

    Guo, Hai-Dong; Zhang, Qing-Feng; Chen, Ji-Guang; Shangguang, Xin-Cheng; Guo, Yu-Xian

    2015-02-01

    Puerarin is the major isoflavone of Puerariae Lobatae Radix. A method for large scale purification of puerarin was developed through resins adsorption and acid hydrolysis. The adsorption properties of six macroporous resins (D101, S-8, H103, X-5, HPD600, AB-8) were compared through the adsorption kinetics and equilibrium adsorption isotherms. Results showed that H103 resin had the best adsorption rate and capacity. The mass transfer zone motion model was further used for analyzing the fixed bed adsorption of H103 resin. Its length of mass transfer zone with 2mg/ml of puerarin in water and 10% ethanol at flow rate of 10ml/min were 41.6 and 47.5cm, while the equilibrium adsorption capacity was 165.03 and 102.88mg/g, respectively. By using 75% ethanol, puerarin could be well desorbed from the resin with recovery of 97.4%. Subsequently, H103 resin was successfully used for puerarin purification from Puerariae Lobatae Radix. The content of total isoflavones and puerarin in the resin adsorption product were 69.25% and 41.78%, respectively, which were about three times increased compared to the crude extract. Then, the product was hydrolyzed by 2.5M HCl at 90°C for 1h. Puerarin with purity of 90% and a byproduct daidzein with purity of 78% were obtained. PMID:25553536

  8. Bioaccumulation of PCBs by algae: Kinetics versus equilibrium

    SciTech Connect

    Swackhamer, D.L.; Skoglund, R.S. )

    1993-05-01

    The objectives of this study were to test the hypothesis that bioaccumulation of hydrophobic organic compounds (HOCs) by phytoplankton is correlated to the compound's octanol/water partition coefficient (K[sub ow]) in a predictive relationship in laboratory experiments, and to confirm these findings with field observations. In laboratory experiments the authors measured the uptake of 40 representative polychlorinated biphenyl (PCB) congeners over time under conditions that inhibited and allowed phytoplankton growth. Results indicated that the bioaccumulation process is consistent with partitioning from water into cell lipids but is slower than previously thought. The uptake of PCBs was slow relative to growth of phytoplankton, preventing the chemical from reaching thermodynamic equilibrium in algal cells under conditions promoting growth (nonwinter). Thus under non-winter field conditions, many PCB congeners never reach equilibrium concentrations. Food-chain models that assume equilibrium between HOCs and the primary trophic level could be inaccurate and may need to use a kinetic framework.

  9. Adsorption equilibria of chloropentafluoroethane and pentafluoroethane on activated carbon pellet

    SciTech Connect

    Moon, D.J.; Chung, M.J.; Cho, S.Y.; Ahn, B.S.; Park, K.Y.; Hong, S.I.

    1998-09-01

    Chlorofluorocarbons (CFCs) have been widely used as refrigerants, blowing agents, propellants, and cleaning agents. However, their roles in the ozone depletion are of great global concern. In addition, CFCs also contribute to the greenhouse effect and hence to climate change. Therefore, the Montreal Protocol was formulated to restrict the release of CFCs into the atmosphere. This leads to research for ways to recover the halogenated hydrocarbons. Equilibrium studies on the adsorption of chloropentafluoroethane (R-115, CF{sub 3}CF{sub 2}Cl) and pentafluoroethane (CF{sub 3}CF{sub 2}H, R-125) on an activated carbon pellet were made between 298.2 K and 373.6 K. Equilibrium parameters based on the Langmuir-Freundlich equation are derived. The Langmuir-Freundlich isotherms for R-115 and R-125 fit the experimental results within 2%. The isosteric enthalpies of adsorption of R-115 and R-125 were estimated.

  10. Adsorption / Desorption Behavior of Water Vapor in an Adsorbent Desiccant Rotor

    NASA Astrophysics Data System (ADS)

    Tsujiguchi, Takuya; Kodama, Akio

    Adsorption / desorption behavior of water vapor onto desiccant rotor has been investigated to improve the desiccant cooling system by means of computer simulation. In this paper, we paid attention to the relationship between the equilibrium amount of water adsorbed onto the desiccant material and the relative humidity, that is adsorption isotherm as a principal characteristic feature of adsorbent. Considering actual adsorbents, five types of adsorption isotherms were assumed to clarify the influence of adsorption isotherm on the dehumidifying performance. After the investigation on the influences of some operating conditions on the dehumidifying performance at each selected adsorption isotherm, it was found that higher dehumidifying performance and reduction of length of desiccant rotor could be achieved by selecting appropriate adsorption isotherm. It was also predicted that S-shaped adsorption isotherm which is raised sharply at relative humidity around 15 % could produce the lowest air humidity at regeneration air temperature 80 °C. Moreover influence of the intraparticle diffusion coefficient which significantly influence on the adsorption / desorption rate was discussed choosing two adsorption isotherm from the above five isotherms. It seems that effective range of the intraparticle diffusion coefficient for the significant improvement of the dehumidifying performance was strongly influenced by the shape of adsorption isotherm.

  11. Adsorption characteristics of cellulase and β-glucosidase on Avicel, pretreated sugarcane bagasse, and lignin.

    PubMed

    Machado, Daniele Longo; Moreira Neto, João; da Cruz Pradella, José Geraldo; Bonomi, Antonio; Rabelo, Sarita Cândida; da Costa, Aline Carvalho

    2015-01-01

    Although adsorption is an essential step in the enzymatic hydrolysis of lignocellulosic materials, literature reports controversial results in relation to the adsorption of the cellulolitic enzymes on different biomasses/pretreatments, which makes difficult the description of this phenomenon in hydrolysis mathematical models. In this work, the adsorption of these enzymes on Avicel and sugarcane bagasse pretreated by the hydrothermal bagasse (HB) and organosolv bagasse (OB) methods was evaluated. The results have shown no significant adsorption of β-glucosidase on Avicel or HB. Increasing solids concentration from 5% (w/v) to 10% (w/v) had no impact on the adsorption of cellulase on the different biomasses if stirring rates were high enough (>100 rpm for Avicel and >150 rpm for HB and OB). Adsorption equilibrium time was low for Avicel (10 Min) when compared with the lignocellulosic materials (120 Min). Adsorption isotherms determined at 4 and 50 °C have shown that for Avicel there was a decrease in the maximum adsorption capacity (Emax) with the temperature increase, whereas for HB increasing temperature increased Emax . Also, Emax increased with the content of lignin in the material. Adsorption studies of cellulase on lignin left after enzymatic digestion of HB show lower but significant adsorption capacity (Emax = 11.92 ± 0.76 mg/g). PMID:25322902

  12. Atrazine adsorption removal with nylon6/polypyrrole core-shell nanofibers mat: possible mechanism and characteristics

    NASA Astrophysics Data System (ADS)

    Yang, Bi-Yi; Cao, Yang; Qi, Fei-Fei; Li, Xiao-Qing; Xu, Qian

    2015-05-01

    A functionalized nylon6/polypyrrole core-shell nanofibers mat (PA6/PPy NFM) was prepared via situ polymerization on nylon6 electrospun nanofibers mat (PA6 NFM) template and used as an adsorbent to remove atrazine from aqueous solutions. The core-shell structure of PA6/PPy NFM can be clearly proved under scanning electron microscope (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The effects of initial solution pH and ionic strength, as well as the comparison of the adsorption capacity of functionalized (PA6/PPy NFM) and non-functionalized (PA6 NFM) adsorbent, were examined to reveal the possible adsorption mechanism. The results indicated that π-π interaction and electrostatic interaction should play a key role in the adsorption process. The kinetics and thermodynamics studies also further elucidated the detailed adsorption characteristics of atrazine removal by PA6/PPy NFM. The adsorption of atrazine could be well described by the pseudo-second-order equation. The adsorption equilibrium data was well fitted with the Freundlich isotherm model with a maximum adsorption capacity value of 14.8 mg/g. In addition, the increase of adsorption rate caused by a temperature increase could be felicitously explained by the endothermic reaction. The desorption results showed that the adsorption capacity remained almost unchanged after six adsorption/desorption cycles. These results suggest that PA6/PPy NFM could be employed as an efficient adsorbent for removing atrazine from contaminated water sources.

  13. Adsorption Characteristics of Pb(2+) onto Wine Lees-Derived Biochar.

    PubMed

    Zhu, Qihong; Wu, Jun; Wang, Lilin; Yang, Gang; Zhang, Xiaohong

    2016-08-01

    Biochar has great advantages in soil amendment and polluted soil remediation. Herein, the pore and adsorption properties of wine lees-derived biochar were explored. Specifically, the adsorption isotherm and kinetics of Pb(2+) onto wine lees-derived biochar were examined. Experimental results revealed that wine lees-derived biochar featured large specific surface area and total pore volume, and high contents of -COOH and -OH on its surface. Adsorption of Pb(2+) onto wine lees-derived biochar proceeded via a multilayer adsorption mechanism, as described by the Freundlich adsorption model. Adsorption kinetics followed the Lagergren pseudo-second-order kinetics model; adsorption equilibrium was achieved within 30-60 min. Furthermore, the effect of solution pH on the adsorption of Pb(2+) was investigated. Within the studied pH range of 3-6, the adsorption capacity increased with increasing pH. Under established optimized conditions, wine lees-derived biochar achieved a Pb(2+) adsorption capacity of 79.12 mg/g. PMID:26920696

  14. AgII doped MIL-101 and its adsorption of iodine with high speed in solution

    NASA Astrophysics Data System (ADS)

    Mao, Ping; Qi, Bingbing; Liu, Ying; Zhao, Lei; Jiao, Yan; Zhang, Yi; Jiang, Zheng; Li, Qiang; Wang, Jinfeng; Chen, Shouwen; Yang, Yi

    2016-05-01

    In order to improve the adsorption speed of iodine from water, MIL-101 with extra-large specific surface area (3054 m2/g) was chosen as a base material, and then, Ag was doped into MIL-101 to enhance its adsorption capacity through an incipient-wetness impregnation method. With the characterization of SEM-EDS, TEM, XRD, XPS, TGA, IR, and BET techniques, the resulting Ag was identified to be stay in the framework of MIL-101 stably in the form of AgII (generally, AgII cation is not stable). However, after the adsorption of I- anions, AgII stay in the cages of MIL-101 in the form of AgI/AgI3. It is important to note that, all adsorbents show high adsorption speed of iodine in solution. The equilibrium adsorption time of the adsorbents were acquired by only a few minutes, which can be attributed to its large BET surface area. An interesting note is that, when the doping amount of Ag is less than 9%, the iodine anions adsorption capacity of Ag@MIL-101 is greater than its theoretical adsorption capacity. It shows that both physical adsorption and chemical adsorption are existed in the adsorption process. This study hopefully leads to a new and highly efficient Ag-based adsorbent for iodide adsorb from solutions.

  15. ALMA telescope reaches new heights

    NASA Astrophysics Data System (ADS)

    2009-09-01

    of the Array Operations Site. This means surviving strong winds and temperatures between +20 and -20 Celsius whilst being able to point precisely enough that they could pick out a golf ball at a distance of 15 km, and to keep their smooth reflecting surfaces accurate to better than 25 micrometres (less than the typical thickness of a human hair). Once the transporter reached the high plateau it carried the antenna to a concrete pad - a docking station with connections for power and fibre optics - and positioned it with an accuracy of a few millimetres. The transporter is guided by a laser steering system and, just like some cars today, also has ultrasonic collision detectors. These sensors ensure the safety of the state-of-the-art antennas as the transporter drives them across what will soon be a rather crowded plateau. Ultimately, ALMA will have at least 66 antennas distributed over about 200 pads, spread over distances of up to 18.5 km and operating as a single, giant telescope. Even when ALMA is fully operational, the transporters will be used to move the antennas between pads to reconfigure the telescope for different kinds of observations. "Transporting our first antenna to the Chajnantor plateau is a epic feat which exemplifies the exciting times in which ALMA is living. Day after day, our global collaboration brings us closer to the birth of the most ambitious ground-based astronomical observatory in the world", said Thijs de Graauw, ALMA Director. This first ALMA antenna at the high site will soon be joined by others and the ALMA team looks forward to making their first observations from the Chajnantor plateau. They plan to link three antennas by early 2010, and to make the first scientific observations with ALMA in the second half of 2011. ALMA will help astronomers answer important questions about our cosmic origins. The telescope will observe the Universe using light with millimetre and submillimetre wavelengths, between infrared light and radio waves in

  16. ALMA Telescope Reaches New Heights

    NASA Astrophysics Data System (ADS)

    2009-09-01

    ball at a distance of nine miles, and to keep their smooth reflecting surfaces accurate to less than the thickness of a human hair. Once the transporter reached the high plateau it carried the antenna to a concrete pad -- a docking station with connections for power and fiber optics -- and positioned it with an accuracy of a small fraction of an inch. The transporter is guided by a laser steering system and, just like some cars, also has ultrasonic collision detectors. These sensors ensure the safety of the state-of-the-art antennas as the transporter drives them across what will soon be a rather crowded plateau. Ultimately, ALMA will have at least 66 antennas distributed over about 200 pads, spread over distances of up to 11.5 miles and operating as a single, giant telescope. Even when ALMA is fully operational, the transporters will be used to move the antennas between pads to reconfigure the telescope for different kinds of observations. This first ALMA antenna at the high site will soon be joined by others, and the ALMA team looks forward to making their first observations from the Chajnantor plateau. They plan to link three antennas by early 2010, and to make the first scientific observations with ALMA in the second half of 2011. ALMA will help astronomers answer important questions about our cosmic origins. The telescope will observe the Universe using light with millimeter and submillimeter wavelengths, between infrared light and radio waves in the electromagnetic spectrum. Light at these wavelengths comes from some of the coldest, and from some of the most distant objects in the cosmos. These include cold clouds of gas and dust where new stars are being born, or remote galaxies towards the edge of the observable universe. The Universe is relatively unexplored at submillimeter wavelengths, as the telescopes need extremely dry atmospheric conditions, such as those at Chajnantor, and advanced detector technology. The Atacama Large Millimeter/submillimeter Array

  17. Napoleon Is in Equilibrium

    PubMed Central

    Phillips, Rob

    2016-01-01

    It has been said that the cell is the test tube of the twenty-first century. If so, the theoretical tools needed to quantitatively and predictively describe what goes on in such test tubes lag sorely behind the stunning experimental advances in biology seen in the decades since the molecular biology revolution began. Perhaps surprisingly, one of the theoretical tools that has been used with great success on problems ranging from how cells communicate with their environment and each other to the nature of the organization of proteins and lipids within the cell membrane is statistical mechanics. A knee-jerk reaction to the use of statistical mechanics in the description of cellular processes is that living organisms are so far from equilibrium that one has no business even thinking about it. But such reactions are probably too hasty given that there are many regimes in which, because of a separation of timescales, for example, such an approach can be a useful first step. In this article, we explore the power of statistical mechanical thinking in the biological setting, with special emphasis on cell signaling and regulation. We show how such models are used to make predictions and describe some recent experiments designed to test them. We also consider the limits of such models based on the relative timescales of the processes of interest. PMID:27429713

  18. Napoleon Is in Equilibrium

    NASA Astrophysics Data System (ADS)

    Phillips, Rob

    2015-03-01

    It has been said that the cell is the test tube of the twenty-first century. If so, the theoretical tools needed to quantitatively and predictively describe what goes on in such test tubes lag sorely behind the stunning experimental advances in biology seen in the decades since the molecular biology revolution began. Perhaps surprisingly, one of the theoretical tools that has been used with great success on problems ranging from how cells communicate with their environment and each other to the nature of the organization of proteins and lipids within the cell membrane is statistical mechanics. A knee-jerk reaction to the use of statistical mechanics in the description of cellular processes is that living organisms are so far from equilibrium that one has no business even thinking about it. But such reactions are probably too hasty given that there are many regimes in which, because of a separation of timescales, for example, such an approach can be a useful first step. In this article, we explore the power of statistical mechanical thinking in the biological setting, with special emphasis on cell signaling and regulation. We show how such models are used to make predictions and describe some recent experiments designed to test them. We also consider the limits of such models based on the relative timescales of the processes of interest.

  19. KEMOD: A mixed chemical kinetic and equilibrium model of aqueous and solid phase geochemical reactions

    SciTech Connect

    Yeh, G.T.; Iskra, G.A.; Szecsody, J.E.; Zachara, J.M.; Streile, G.P.

    1995-01-01

    This report presents the development of a mixed chemical Kinetic and Equilibrium MODel in which every chemical species can be treated either as a equilibrium-controlled or as a kinetically controlled reaction. The reaction processes include aqueous complexation, adsorption/desorption, ion exchange, precipitation/dissolution, oxidation/reduction, and acid/base reactions. Further development and modification of KEMOD can be made in: (1) inclusion of species switching solution algorithms, (2) incorporation of the effect of temperature and pressure on equilibrium and rate constants, and (3) extension to high ionic strength.

  20. Adsorption of organic solvent vapors on hydrophobic Y-type zeolite

    SciTech Connect

    Yun, J.H.; Choi, D.K.; Kim, S.H.

    1998-06-01

    Experimental isotherms and prediction results for adsorption of benzene, toluene, dichloromethane and 1,1-dichloro-1-fluoroethane on hydrophobic Y-type zeolite are reported. Isotherm shows the type-V shape according to the classification by Brunauer et al. A simple thermodynamic method is employed to predict the experimental equilibrium data at various temperatures simultaneously. This plain method is based on the assumption that the value of the isosteric heat of adsorption does not depend on temperature for a certain surface loading. The Clausius-Clapeyron equation was used to calculate the isosteric heat of adsorption. To apply the method, only two sets of the experimental isotherm data at two different temperatures are needed. The Clausius-Clapeyron equation with two isotherms provided simple and reliable prediction of adsorption equilibrium relationships at various temperatures. Results with this method showed that the predicted value agrees well with the experimental data in the range of temperatures for the system tested.

  1. Possibility of using adsorption refrigeration unit in district heating network

    NASA Astrophysics Data System (ADS)

    Grzebielec, Andrzej; Rusowicz, Artur; Jaworski, Maciej; Laskowski, Rafał

    2015-09-01

    Adsorption refrigeration systems are able to work with heat sources of temperature starting with 50 °C. The aim of the article is to determine whether in terms of technical and economic issues adsorption refrigeration equipment can work as elements that produce cold using hot water from the district heating network. For this purpose, examined was the work of the adsorption air conditioning equipment cooperating with drycooler, and the opportunities offered by the district heating network in Warsaw during the summer. It turns out that the efficiency of the adsorption device from the economic perspective is not sufficient for production of cold even during the transitional period. The main problem is not the low temperature of the water supply, but the large difference between the coefficients of performance, COPs, of adsorption device and a traditional compressor air conditioning unit. When outside air temperature is 25 °C, the COP of the compressor type reaches a value of 4.49, whereas that of the adsorption device in the same conditions is 0.14. The ratio of the COPs is 32. At the same time ratio between the price of 1 kWh of electric power and 1 kWh of heat is only 2.85. Adsorption refrigeration equipment to be able to compete with compressor devices, should feature COPads efficiency to be greater than 1.52. At such a low driving temperature and even changing the drycooler into the evaporative cooler it is not currently possible to achieve.

  2. The adsorption and mass-transfer process of cationic red X-GRL dye on natural zeolite.

    PubMed

    Tian, Jingjing; Guan, Junfang; Gao, Huimin; Wen, Yafei; Ren, Zijie

    2016-01-01

    The adsorption behavior of natural zeolite was studied in order to determine the adsorption capacity and mass-transfer process of cationic red X-GRL (C(18)H(21)BrN(6)) onto the adsorbent. The adsorption tests to determine both the uptake capacity and the mass-transfer process at equilibrium were performed under batch conditions, which showed rapid uptake in general for the initial 5 min, corresponding to 92% total removal. The equilibrium adsorption capacity value (q(e,cal)) in pseudo-second-order kinetics was 13.51 mg/g at 293 K and the whole adsorption process was governed by physical adsorption with an endothermic, endothermic spontaneous nature. Adsorption tests indicated that the zeolite has great potential as an alternative low-cost material in the treatment of X-GRL drainage. However, the mass-transfer process to determine the rate-controlling steps showed that both film diffusion and pore diffusion were important in controlling the adsorption rate. The adsorption process was governed by film diffusion while pore diffusion was poor because the X-GRL molecules could not penetrate into the zeolite easily. The X-GRL molecules were only adsorbed on the external surface of the zeolite. Hence, to improve the adsorption capacity of natural zeolite further, modification to expand its micropores is necessary. PMID:27148713

  3. Adsorption of Cadmium, Nickel and Zinc in a Brazilian Oxisoil

    NASA Astrophysics Data System (ADS)

    Casagrande, José Carlos; Martins, Susian Christian; Soares, Marcio Roberto

    2010-05-01

    The adsorption reactions mechanisms provide the understanding of the pollutant fate metals and often control the bioavailability and transport of heavy metals ions in soil, indicating the preventive environmental control. The cadmium, nickel and zinc behavior in the soils are explained by the reactions of adsorption, influenced by pH and ionic strength. The objective of this work was to study the influence of those factors on cadmium, nickel and zinc adsorption in an oxisol. It was studied the Cd, Ni and Zn adsorption in soil samples of the State of São Paulo (Anionic "Xanthic" Acrudox), collected in surface and in depth and submitted to solutions of Ca(NO3)2 1,0; 0,1 and 0,01 mol L-1. The pH of the samples from 3,0 to 10,0 was varied adding NaOH or HCl 4 mol L-1 not surpassing 2% of the electrolyte volume. The soil samples received 5,0 mg dm-3 of cadmium, nickel and zinc, ratio 1:10 (2,0 g of soil: 20 solution ml) and were shacked for 24 hours. The cadmium, nickel and zinc adsorption increased with pH, reaching it picks at pH 7,0 for cadmium and approximately at pH 6,0 for nickel and zinc. This indicates that zinc and nickel have higher affinity than cadmium with the soil colloids, because it reached the maximum adsorption in a small pH value. In other words, the amount of negative charges necessary to promote the maximum adsorption was small for zinc. The influence of ionic strengths was small for cadmium, nickel and zinc adsorption, being similar from pH 3,0 to 10,0, in surface soil layer and in depth, demonstrating that competition with Ca2+ for the retention colloid sites of the soils didn't interfere in the adsorption. In that way, it is supposed that cadmium, nickel and zinc binding energy is high in a soil rich in Fe and Al oxides. Adsorption of cadmium, nickel and zinc was similar for the ionic strengths, not depending on PZSE. The cadmium, nickel and zinc adsorption increased with pH elevation, with small ionic strength influence. Nickel and zinc have

  4. New Adsorption Methods.

    ERIC Educational Resources Information Center

    Wankat, Phillip C.

    1984-01-01

    Discusses a simple method for following the movement of a solute in an adsorption or ion exchange system. This movement is used to study a variety of operational methods, including continuous flow and pulsed flow counter-current operations and simulated counter-current systems. Effect of changing thermodynamic variables is also considered. (JM)

  5. Adsorption of 2,4-dichlorophenoxyacetic acid by an Andosol.

    PubMed

    Hiradate, Syuntaro; Furubayashi, Akihiro; Uchida, Natsuyo; Fujii, Yoshiharu

    2007-01-01

    To identify the important soil components involved in 2,4-dichlorophenoxyacetic acid (2,4-D) adsorption on Andosols, 2,4-D adsorption on a surface horizon of an Andosol was compared with that on hydrogen peroxide (H2O2)-treated (soil organic matter [SOM] was removed), acid-oxalate (OX)-treated (active metal hydroxides and SOM were removed), and dithionite-citrate-bicarbonate (DCB)-treated (free and active metal [hydr]oxides and SOM were removed) soil samples at equilibrium pHs ranging from 4 to 8. Although the untreated soil contained a large amount of organic C (71.9 g kg-1), removal of SOM had little effect on 2,4-D adsorption. Active surface hydroxyls, which were attached to the active and free metal (hydr)oxides and metal SOM complexes, were identified as the most important soil functional group for 2,4-D adsorption. The dominant mechanism of the 2,4-D adsorption was a ligand exchange reaction in which the carboxylic group of 2,4-D displaced the active surface hydroxyl associated with metals and formed a strong coordination bond between the 2,4-D molecule and soil solid phase. The ligand exchange reaction reasonably accounted for the selective adsorption of 2,4-D over Cl-, competitive adsorption of phosphate over 2,4-D, reduction in plant-growth-inhibitory activity of soil-adsorbed 2,4-D, and the high 2,4-D adsorption ability of Andosols. Although a humic acid purified from the soil did not adsorb 2,4-D, the presence of the humic acid increased 2,4-D adsorption on Al and Fe, probably by inhibiting the hydrolysis and polymerization of Al and Fe resulting in the preservation of available adsorption sites on these metals. The adsorption behavior of 2,4-D on soils could be a good index for predicting the adsorption behavior of other organic acids in soils. PMID:17215217

  6. Removal of phenol and chlorophenols from water by coir pith carbon: equilibrium and rate studies.

    PubMed

    Namasivayam, C; Kavitha, D

    2004-07-01

    Batch mode studies were conducted to study the removal of phenol, 2,4,6-Trichlorophenol (TCP) and Pentachlorophenol (PCP) from aqueous solution on coir pith carbon by adsorption process under varying experimental conditions such as agitation time, adsorbent dose, pH and temperature. Kinetics of adsorption obeyed second order rate equation and the rate constant was found to be in the range 0.0098-0.0672, 0.0949-0.8801 and 0.172-0.305 g/mg/min for phenol, TCP and PCP respectively. Equilibrium adsorption data follow Langmuir isotherm for phenol and PCP and the adsorption capacities were found to be 48.3 mg and 3.7 mg/g, respectively. For TCP, adsorption followed Freundlich isotherm only. Acidic pH was favorable for the adsorption of all the chlorophenols. Studies on pH effect and desorption show that chemisorption seems to play a major rule in the adsorption process. The positive values of H0 24.99, 18.69, and 8.907 kJ/mol for phenol, TCP and PCP respectively, confirm the endothermic nature of adsorption. PMID:16669312

  7. Adsorption of methyl orange and salicylic acid on a nano-transition metal composite: Kinetics, thermodynamic and electrochemical studies.

    PubMed

    Arshadi, M; Mousavinia, F; Amiri, M J; Faraji, A R

    2016-12-01

    In this work synthesis of Mn-nanoparticles (MnNPs) supported on the Schiff base modified nano-sized SiO2Al2O3 mixed-oxides (Si/Al) and its implementation as an adsorbent for the removal of organic pollutions such as methyl orange (MO) and salicylic acid (SA) was investigated. Si/Al were functionalized by grafting Schiff base ligand and in the next step, MnNPs were prepared over the modified nano sol-gel Si/Al. Structures and adsorption characteristics of the obtained organometallic-modified SiO2/Al2O3 mixed oxide were studied by several methods such as elemental analysis, diffuse reflectance UV-vis spectroscopy, FT-IR spectroscopy, nitrogen adsorption/desorption, scanning electron microscope (SEM), transmission electron microscope (TEM), energy dispersive X-ray (EDX), inductively coupled plasma (ICP-AES), Electron Paramagnetic Resonance (EPR), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). EPR data of the immobilized manganese ions resulted that the transition state of active sites in the nano-adsorbent are in the form of Mn(II) ions at the surface. The adsorption properties of heterogeneous Mn(II) ions showed that this nano-adsorbent has very good potential to remove MO and SA ions from aqueous solution. The removal efficiency of the SAPAS@MnNPs towards MO reached out to 89.3 and 29.1% and for SA approached to 54.6 and 18.9% at 150 and 500mg/dm(3) initial organic pollution concentrations, respectively. To investigate the adsorption kinetic of Mn(II) ions onto the nano-sized support, pseudo first and pseudo second order kinetics, and the Freundlich, Langmuir and Langmuir-Freundlich isotherm models have also been applied to the equilibrium adsorption data. The contact time to obtain equilibrium for maximum adsorption capacity was 45min. The adsorption process was spontaneous and endothermic in nature and it was well explained with pseudo-second-order kinetic model. No remarkable loss of removal capacity even after 8th times regeneration

  8. Chlorine adsorption on the InAs (001) surface

    SciTech Connect

    Bakulin, A. V.; Eremeev, S. V.; Tereshchenko, O. E.; Kulkova, S. E.

    2011-01-15

    Chlorine adsorption on the In-stabilized InAs(001) surface with {zeta}-(4 Multiplication-Sign 2) and {beta}3 Prime -(4 Multiplication-Sign 2) reconstructions and on the Ga-stabilized GaAs (001)-{zeta}-(4 Multiplication-Sign 2) surface has been studied within the electron density functional theory. The equilibrium structural parameters of these reconstructions, surface atom positions, bond lengths in dimers, and their changes upon chlorine adsorption are determined. The electronic characteristics of the clean surface and the surface with adsorbed chlorine are calculated. It is shown that the most energetically favorable positions for chlorine adsorption are top positions over dimerized indium or gallium atoms. The mechanism of chlorine binding with In(Ga)-stabilized surface is explained. The interaction of chlorine atoms with dimerized surface atoms weakens surface atom bonds and controls the initial stage of surface etching.

  9. Tritium Isotope Separation Using Adsorption-Distillation Column

    SciTech Connect

    Fukada, Satoshi

    2005-07-15

    In order to miniaturize the height of a distillation tower for the detritiation of waste water from fusion reactors, two experiments were conducted: (1) liquid frontal chromatography of tritium water eluting through an adsorption column and (2) water distillation using a column packed with adsorbent particles. The height of the distillation tower depends on the height equivalent to a theoretical plate, HETP, and the equilibrium isotope separation factor, {alpha}{sub H-T}{sup equi}. The adsorption action improved not only HETP but also {alpha}{sub H-T}{sup equi}. Since the adsorption-distillation method proposed here can shorten the tower height with keeping advantages of the distillation, it may bring an excellent way for miniaturizing the distillation tower to detritiate a large amount of waste water from fusion reactors.

  10. Adsorption of acenaphthene on porous organic polymers

    SciTech Connect

    Eichenmueller, B.; Bunke, G.; Buchholz, R.; Goetz, P.; Behrend, K.

    1997-09-01

    Adsorption behavior of the three-ring polynuclear aromatic hydrocarbon (PAH) acenaphthene from aqueous solutions on the adsorber polymers Wofatit EP 61 and EP 63 was examined. Using dimethylsulfoxide as a solubilizer, equilibrium, kinetic, and fixed-bed dynamic experiments could be carried out. Freundlich parameters for equilibrium data were obtained, exhibiting high capacities at low liquid concentrations: K{sub F} = 0.14 mg{sup 1{minus}n} {center_dot} L{sup n}/mg{sub A} and n = 0.5 for EP 61; and K{sub F} = 0.22 mg{sup 1{minus}n} {center_dot} L/mg{sub A} and n = 0.39 for EP 63. By fitting the numerical solution of a mathematical model to experimental data from kinetic experiments in a differential bed adsorber operated at high circulation velocity, effective intraparticle diffusivity could be estimated to be D{sub eff} = 2.5 {center_dot} 10{sup {minus}10} cm{sup 2}/s. According to these data and parameters from empirical equations, breakthrough curves were predicted analytically and numerically and compared to experimental data. A good agreement with the numerical solution was observed. The presence of dimethylsulfoxide influenced neither equilibrium nor kinetic data.

  11. Interactions of xanthines with activated carbon. I. Kinetics of the adsorption process

    NASA Astrophysics Data System (ADS)

    Navarrete Casas, R.; García Rodriguez, A.; Rey Bueno, F.; Espínola Lara, A.; Valenzuela Calahorro, C.; Navarrete Guijosa, A.

    2006-06-01

    Because of their pharmaceutical and industrial applications, we have studied the adsorption of xanthine derivates (caffeine and theophylline) by activated carbon. To this end, we examined kinetic, equilibrium and thermodynamic aspects of the process. This paper reports the kinetics results. The experimental results indicate that the process was first order in C and the overall process was assumed to involve a single, reversible adsorption-desorption process obeying a kinetic law postulated by us.

  12. Rapid-Equilibrium Enzyme Kinetics

    ERIC Educational Resources Information Center

    Alberty, Robert A.

    2008-01-01

    Rapid-equilibrium rate equations for enzyme-catalyzed reactions are especially useful because if experimental data can be fit by these simpler rate equations, the Michaelis constants can be interpreted as equilibrium constants. However, for some reactions it is necessary to use the more complicated steady-state rate equations. Thermodynamics is…

  13. Comparing the removal of perchlorate when using single-walled carbon nanotubes (SWCNTs) or granular activated carbon: adsorption kinetics and thermodynamics.

    PubMed

    Lou, Jie C; Hsu, Yung S; Hsu, Kai L; Chou, Ming S; Han, Jia Y

    2014-01-01

    This study aims to remove perchlorate using single-walled carbon nanotubes (SWCNTs) or granular activated carbon (GAC). Dynamic and equilibrium adsorption experiments were performed to evaluate the thermodynamic behavior of perchlorate on SWCNTs and GAC. Key parameters affecting the adsorption, such as pH, ionic strength, and temperature were studied. The experimental results showed that the dynamic adsorption experiment achieved equilibrium in approximately eight hours. The adsorption capacity increased as the concentration of perchlorate increased or as the ionic strength decreased. The selected adsorption models were the modified Freundlich, the pseudo-1st-order, and the pseudo-2nd-order equations. The results showed that the modified Freundlich equation best described the kinetic adsorption processes. The maximal adsorption capacities of GAC and SWCNTs were 33.87-28.21 mg/g and 13.64 - 10.03 mg/g, respectively, at a constant temperature between 5°C and 45°C. The thermodynamic parameters, such as the equilibrium constant (K0 ), the standard free energy changes (ΔG°), the standard enthalpy change (ΔH°) and the standard entropy change (ΔS°), were obtained. The results of the isothermal equilibrium adsorption experiment showed that low pH levels, low ionic strength, and low-temperature conditions facilitated the perchlorate adsorption, indicating that GAC and SWCNTs are potential absorbents for water treatment. PMID:24410681

  14. Adsorption of copper cyanide on chemically active adsorbents

    SciTech Connect

    Lee, J.S.; Deorkar, N.V.; Tavlarides, L.L.

    1998-07-01

    An inorganic chemically active adsorbent (ICAA), SG(1)-TEPA (tetraethylenepentaamine)-propyl, is developed for removal, recovery, and recycling of copper cyanide from industrial waste streams. Equilibrium studies are executed to determine and model adsorption of the copper cyanide complex from aqueous solutions in a batch and packed column. It appears that adsorption is dependent on anionic copper cyanide species and the basicity of the ligand. Aqueous-phase equilibrium modeling shows that monovalent (Cu(CN){sub 2}{sup {minus}}), divalent (Cu(CN){sub 3}{sup 2{minus}}), and trivalent (Cu(CN){sub 4}{sup 3{minus}}) species of copper cyanide exist in the solution, depending on the pH and the concentration of total cyanide ions. Batch adsorption data are modeled using a modified multicomponent Langmuir isotherm which includes aqueous-phase speciation and basicity of the SG(1)-TEPA-propyl. This developed model is applied with a mass balance equation to describe the adsorption of copper cyanide complexes in a packed column.

  15. [Adsorption Characteristics of Norfloxacin by Biochars Derived from Reed Straw and Municipal Sludge].

    PubMed

    Zhang, Han-yu; Wang, Zhao-wei; Gao, Jun-hong; Zhu, Jun-min; Xie, Chao-ran; Xie, Xiao-yun

    2016-02-15

    Two types of biochars were prepared by pyrolyzing reed straw and municipal sludge at the temperature of 500 degrees C. The structure and properties of biochars were characterized by BET, scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and fourier transform infrared spectroscopy ( FTIR ). The effects of pH value, adsorption time, temperature and initial concentration of norfloxacin (NOR) on the adsorption behaviors were determined by single factor experiments, which were used to preliminarily discuss adsorption mechanism. The results showed that the adsorption of NOR onto biochars derived from reed straw and municipal sludge could reach 70% and 60% of the total adsorption within 12 h, respectively; the maximum adsorption capacities of the two biochars were 2.13 mg x g(-1) (biochar derived from reed straw) and 2.09 mg x g(-1) (biochar derived from municipal sludge). The quantities of both absorptions increased with the decreasing solution pH. The two adsorption kinetics of NOR onto biochars followed the pseudo second order kinetic equations, and adsorption isotherms fitted well with the Langmuir equations. Adsorption thermodynamics parameters such as Gibbs free energy (AG), enthalpy (AH) and entropy (AS) indicated that the two adsorptions were endothermic reactions. Infrared spectroscopy analysis indicated that oxygen-containing functional groups on biochars provided NOR molecules with adsorptive sites, which facilitated the formation of hydrogen bonds between NOR and the biochars. PMID:27363161

  16. Is Soret equilibrium a non-equilibrium effect?

    NASA Astrophysics Data System (ADS)

    Würger, Alois

    2013-04-01

    Recent thermophoretic experiments on colloidal suspensions revived an old debate, namely whether the Soret effect is properly described by thermostatics, or necessarily requires non-equilibrium thermodynamics. Based on colloidal transport theory and the entropy production of the related viscous flow, our analysis leads to the conclusion that the equilibrium approach may work for small ions, yet fails for colloidal particles and polymers. Regarding binary molecular mixtures, our results shed some doubt on the validity of thermostatic approaches that derive the Soret coefficient from equilibrium potentials.

  17. Competitive adsorption of ibuprofen and amoxicillin mixtures from aqueous solution on activated carbons.

    PubMed

    Mansouri, Hayet; Carmona, Rocio J; Gomis-Berenguer, Alicia; Souissi-Najar, Souad; Ouederni, Abdelmottaleb; Ania, Conchi O

    2015-07-01

    This work investigates the competitive adsorption under dynamic and equilibrium conditions of ibuprofen (IBU) and amoxicillin (AMX), two widely consumed pharmaceuticals, on nanoporous carbons of different characteristics. Batch adsorption experiments of pure components in water and their binary mixtures were carried out to measure both adsorption equilibrium and kinetics, and dynamic tests were performed to validate the simultaneous removal of the mixtures in breakthrough experiments. The equilibrium adsorption capacities evaluated from pure component solutions were higher than those measured in dynamic conditions, and were found to depend on the porous features of the adsorbent and the nature of the specific/dispersive interactions that are controlled by the solution pH, density of surface change on the carbon and ionization of the pollutant. A marked roll-up effect was observed for AMX retention on the hydrophobic carbons, not seen for the functionalized adsorbent likely due to the lower affinity of amoxicillin towards the carbon adsorbent. Dynamic adsorption of binary mixtures from wastewater of high salinity and alkalinity showed a slight increase in IBU uptake and a reduced adsorption of AMX, demonstrating the feasibility of the simultaneous removal of both compounds from complex water matrices. PMID:25554087

  18. Adsorption of xenon on vicinal copper and platinum surfaces

    NASA Astrophysics Data System (ADS)

    Baker, Layton

    The adsorption of xenon was studied on Cu(111), Cu(221), Cu(643) and on Pt(111), Pt(221), and Pt(531) using low energy electron diffraction (LEED), temperature programmed desorption (TPD) of xenon, and ultraviolet photoemission of adsorbed xenon (PAX). These experiments were performed to study the atomic and electronic structure of stepped and step-kinked, chiral metal surfaces. Xenon TPD and PAX were performed on each surface in an attempt to titrate terrace, step edge, and kink adsorption sites by adsorption energetics (TPD) and local work function differences (PAX). Due to the complex behavior of xenon on the vicinal copper and platinum metal surfaces, adsorption sites on these surfaces could not be adequately titrated by xenon TPD. On Cu(221) and Cu(643), xenon desorption from step adsorption sites was not apparent leading to the conclusion that the energy difference between terrace and step adsorption is minuscule. On Pt(221) and Pt(531), xenon TPD indicated that xenon prefers to bond at step edges and that the xenon-xenon interaction at step edges in repulsive but no further indication of step-kink adsorption was observed. The Pt(221) and Pt(531) TPD spectra indicated that the xenon overlayer undergoes strong compression near monolayer coverage on these surfaces due to repulsion between step-edge adsorbed xenon and other encroaching xenon atoms. The PAX experiments on the copper and platinum surfaces demonstrated that the step adsorption sites have lower local work functions than terrace adsorption sites and that higher step density leads to a larger separation in the local work function of terrace and step adsorption sites. The PAX spectra also indicated that, for all surfaces studied at 50--70 K, step adsorption is favored at low coverage but the step sites are not saturated until monolayer coverage is reached; this observation is due to the large entropy difference between terrace and step adsorption states and to repulsive interactions between xenon atoms

  19. Reservoir capacity estimates in shale plays based on experimental adsorption data

    NASA Astrophysics Data System (ADS)

    Ngo, Tan

    from different measurement techniques using representative fluids (such as CH4 and CO2) at elevated pressures, and the adsorbed density can range anywhere between the liquid and the solid state of the adsorbate. Whether these discrepancies are associated with the inherent heterogeneity of mudrocks and/or with poor data quality requires more experiments under well-controlled conditions. Nevertheless, it has been found in this study that methane GIP estimates can vary between 10-45% and 10-30%, respectively, depending on whether the free or the total amount of gas is considered. Accordingly, CO2 storage estimates range between 30-90% and 15-50%, due to the larger adsorption capacity and gas density at similar pressure and temperature conditions. A manometric system has been designed and built that allows measuring the adsorption of supercritical fluids in microporous materials. Preliminary adsorption tests have been performed using a microporous 13X zeolite and CO 2 as an adsorbing gas at a temperature of 25oC and 35oC and at pressures up to 500 psi. Under these conditions, adsorption is quantified with a precision of +/- 3%. However, relative differences up to 15-20% have been observed with respect to data published in the literature on the same adsorbent and at similar experimental conditions. While it cannot be fully explained with uncertainty analysis, this discrepancy can be reduced by improving experiment practice, thus including the application of a higher adsorbent's regeneration temperature, of longer equilibrium times and of a careful flushing of the system between the various experimental steps. Based on the results on 13X zeolite, virtual tests have been conducted to predict the performance of the manometric system to measure adsorption on less adsorbing materials, such as mudrocks. The results show that uncertainties in the estimated adsorbed amount are much more significant in shale material and they increase with increasing pressure. In fact, relative

  20. Fundamentals of high pressure adsorption

    SciTech Connect

    Zhou, Y.P.; Zhou, L.

    2009-12-15

    High-pressure adsorption attracts research interests following the world's attention to alternative fuels, and it exerts essential effect on the study of hydrogen/methane storage and the development of novel materials addressing to the storage. However, theoretical puzzles in high-pressure adsorption hindered the progress of application studies. Therefore, the present paper addresses the major theoretical problems that challenged researchers: i.e., how to model the isotherms with maximum observed in high-pressure adsorption; what is the adsorption mechanism at high pressures; how do we determine the quantity of absolute adsorption based on experimental data. Ideology and methods to tackle these problems are elucidated, which lead to new insights into the nature of high-pressure adsorption and progress in application studies, for example, in modeling multicomponent adsorption, hydrogen storage, natural gas storage, and coalbed methane enrichment, was achieved.

  1. Carbon Dioxide Adsorption on a 5A Zeolite Designed for CO2 Removal in Spacecraft Cabins

    NASA Technical Reports Server (NTRS)

    Mulloth, Lila M.; Finn, John E.

    1998-01-01

    Carbon dioxide adsorption data were obtained for a 5A zeolite manufactured by AlliedSignal Inc. (Des Plaines, Illinois). The material is planned for use in the Carbon Dioxide Removal Assembly (CDRA) for U.S. elements of the International Space Station. The family of adsorption isotherms covers a temperature range of O to 250 C, and a pressure range of 0.001 to 800 torr. Coefficients of the Toth equation are fit to the data. Isosteric heats of adsorption are derived from the equilibrium loading data.

  2. Adsorption characteristics of metal ions on chitosan chemically modified by D-galactose

    SciTech Connect

    Kondo, Kazuo; Sumi, Hisaharu; Matsumoto, Michiaki

    1996-07-01

    The adsorption characteristics of metal ions on chitosan chemically modified by D-galactose were examined. The pH dependency on the distribution ratio was found to be affected by the valency of the metal ion, and the apparent adsorption equilibrium constants of the metal ions were determined. The order of adsorption of the metal ions is Ga > In > Nd > Eu for the trivalent metal ions and Cu > Ni > Co for the divalent metal ions. It is believed that amino and hydroxyl groups in the chitosan act as a chelating ligand.

  3. Interlamellar adsorption of organic pollutants from water on hydrophobic clay minerals

    SciTech Connect

    Dekany, I.; Farkas, A.; Kiraly, Z.; Klumpp, E.; Narres, H.D.

    1995-12-01

    The adsorption excess isotherms of n-pentanol and nitrobenzene were determined with surfactant-modified (hexadecylanimonium ions) layered silicates. Both liquids intercalate into the silicate layers and increase the basal spacing, determined by X-ray diffraction measurements, depending on the equilibrium concentration in the bulk phase. To control the entropy change due to the intercalation, flow microcalorimetric experiments were made and enthalpy of displacement isotherms (adsorption and desorption) were determined. The information obtained from these three different measurements permitted the assessment of the composition of the interlarnellar space (in volume fraction of the intercalated molecules) and the thermodynamics of adsorption.

  4. Extracorporeal adsorption of endotoxin.

    PubMed

    Staubach, K H; Rosenfeldt, J A; Veit, O; Bruch, H P

    1997-02-01

    In a porcine endotoxin shock model using a continuous intravenous endotoxin infusion of 250 ng/kg body weight per hour, the cardiorespiratory and hematologic parameters were studied while applying a new on-line polymyxin B immobilized adsorption system. This preliminary report shows that the new adsorbent can remove endotoxin selectively from the circulation and confers a good amount of protection from endotoxin-induced cardiopulmonary decompensation as well as hematologic alterations. Survival time could be extended from 216 min to 313 min. Whereas cardiac output and mean arterial pressure declined critically after 3 h in the controls, the treated group remained stable for another 3 h. These data show that endotoxin adsorption by polymyxin B coupled covalently to acrylic spheres as an adjunctive on-line measure in the septic syndrome seems feasible. PMID:10225785

  5. Helical axis stellarator equilibrium model

    SciTech Connect

    Koniges, A.E.; Johnson, J.L.

    1985-02-01

    An asymptotic model is developed to study MHD equilibria in toroidal systems with a helical magnetic axis. Using a characteristic coordinate system based on the vacuum field lines, the equilibrium problem is reduced to a two-dimensional generalized partial differential equation of the Grad-Shafranov type. A stellarator-expansion free-boundary equilibrium code is modified to solve the helical-axis equations. The expansion model is used to predict the equilibrium properties of Asperators NP-3 and NP-4. Numerically determined flux surfaces, magnetic well, transform, and shear are presented. The equilibria show a toroidal Shafranov shift.

  6. Understanding thermal equilibrium through activities

    NASA Astrophysics Data System (ADS)

    Pathare, Shirish; Huli, Saurabhee; Nachane, Madhura; Ladage, Savita; Pradhan, Hemachandra

    2015-03-01

    Thermal equilibrium is a basic concept in thermodynamics. In India, this concept is generally introduced at the first year of undergraduate education in physics and chemistry. In our earlier studies (Pathare and Pradhan 2011 Proc. episteme-4 Int. Conf. to Review Research on Science Technology and Mathematics Education pp 169-72) we found that students in India have a rather unsatisfactory understanding of thermal equilibrium. We have designed and developed a module of five activities, which are presented in succession to the students. These activities address the students’ alternative conceptions that underlie their lack of understanding of thermal equilibrium and aim at enhancing their understanding of the concept.

  7. Regenerable adsorption system

    NASA Technical Reports Server (NTRS)

    Roychoudhury, Subir (Inventor); Perry, Jay (Inventor); Walsh, Dennis (Inventor)

    2006-01-01

    A method for regenerable adsorption includes providing a substrate that defines at least one layer of ultra short channel length mesh capable of conducting an electrical current therethrough, coating at least a portion of the substrate with a desired sorbent for trace contaminant control or CO.sub.2 sorption, resistively heating the substrate, and passing a flowstream through the substrate and in contact with the sorbent.

  8. Kinetic model of water vapour adsorption by gluten-free starch

    NASA Astrophysics Data System (ADS)

    Ocieczek, Aneta; Kostek, Robert; Ruszkowska, Millena

    2015-01-01

    This study evaluated the kinetics of water vapour adsorption on the surface of starch molecules derived from wheat. The aim of the study was to determine an equation that would allow estimation of water content in tested material in any timepoint of the adsorption process aimed at settling a balance with the environment. An adsorption isotherm of water vapour on starch granules was drawn. The parameters of the Guggenheim, Anderson, and De Boer equation were determined by characterizing the tested product and adsorption process. The equation of kinetics of water vapour adsorption on the surface of starch was determined based on the Guggenheim, Anderson, and De Boer model describing the state of equilibrium and on the model of a first-order linear inert element describing the changes in water content over time.

  9. Application of superparamagnetic microspheres for affinity adsorption and purification of glutathione

    NASA Astrophysics Data System (ADS)

    Wang, Qiang; Guan, Yueping; Yang, Mingzhu

    2012-10-01

    The superparamagnetic poly-(MA-DVB) microspheres with micron size were synthesized by the modified suspension polymerization method. Adsorption of glutathione by magnetic poly-(MA-DVB) microspheres with IDA-copper was investigated. The effect of solution pH value, affinity adsorption and desorption of glutathione was studied. The results showed that the optimum pH value for glutathione adsorption was found at pH=3.5, the maximum capacity for glutathione of magnetic poly-(MA-DVB) microspheres was estimated at 42.4 mg/g by fitting the experimental data to the Langmuir equation. The adsorption equilibrium of glutathione was obtained in about 10 min and the adsorbed glutathione was desorbed from the magnetic microspheres in about 30 min using NaCl buffer solution. The magnetic microspheres could be repeatedly utilized for the affinity adsorption of glutathione.

  10. Investigating the potential of functionalized MCM-41 on adsorption of Remazol Red dye.

    PubMed

    Santos, Danilo Oliveira; de Lourdes Nascimento Santos, Maria; Costa, José Arnaldo Santana; de Jesus, Roberta Anjos; Navickiene, Sandro; Sussuchi, Eliana Midori; de Mesquita, Maria Eliane

    2013-07-01

    The modification of MCM-41 was performed with 3-aminopropropyltrimethoxysilane. The structural order and textural properties of the synthesized materials were studied by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetry/differential thermogravimetry, nitrogen adsorption, and desorption analysis. The adsorption capacity of NH2-MCM-41 was studied with Remazol Red dye. The following parameters were studied in the adsorption process: pH, temperature, adsorbent dosage, and initial concentration. The desorption process was studied in different concentrations of NaOH solutions. The Freundlich isotherm model was found to be fit with the equilibrium isotherm data. Kinetics of adsorption follows the modified Avrami rate equation. The maximum adsorption capacity was estimated to be 45.9 mg g(-1), with removal of the dye of 99.1%. The NH2-MCM-41 material exhibited high desorption capacity with 98.1%. PMID:23334547

  11. SO2 gas adsorption by modified kaolin clays: influence of previous heating and time acid treatments.

    PubMed

    Volzone, Cristina; Ortiga, Jose

    2011-10-01

    Modified kaolin clays were used as adsorbents for SO(2) gas adsorptions. The clays were heated up to 900 °C previous to acid treatments with 0.5 N sulfuric acid solutions at boiling temperature during different times up to 1440 min. Equilibrium adsorption at 25 °C and 0.1 MPa was carried out by using a volumetric apparatus. The samples were characterized by chemical analysis, X-ray diffraction and infrared analysis. The heating of the clays followed by acid treatment improved the adsorption capacity of the kaolin clays. The presence of amorphous silica and hydroxyl in the final products improved SO(2) adsorption capacity. Better properties for SO(2) adsorption were found in kaolin rich in not well ordered kaolinite clay mineral. PMID:21696883

  12. Adsorption of phenolic compounds from aqueous solutions using carbon nanoporous adsorbent coated with polymer

    NASA Astrophysics Data System (ADS)

    Anbia, Mansoor; Ghaffari, Arezoo

    2009-09-01

    Phenolic compounds are a widespread class of water pollutants that are known to cause serious human health problems; and the demand for effective adsorbents for the removal of toxic compounds is increasing. In this work adsorption of phenol, resorcinol and p-cresol on mesoporous carbon material (CMK-1) and modified with polyaniline polymer (CMK-1/PANI) has been investigated in attempt to explore the possibility of using nanoporous carbon as an efficient adsorbent for pollutants. It was found that CMK-1/PANI exhibits significant adsorption for phenolic derivatives. Batch adsorption studies were carried out to study the effect of various parameters like adsorbent dose, pH, initial concentration and contact time. From the sorption studies it was observed that the uptake of resorcinol was higher than other phenolic derivatives. Freundlich and Langmuir adsorption isotherms were used to model the equilibrium adsorption data for phenolic compounds.

  13. Facile synthesis of boehmite/PVA composite membrane with enhanced adsorption performance towards Cr(VI).

    PubMed

    Luo, Lei; Cai, Weiquan; Zhou, Jiabin; Li, Yuanzhi

    2016-11-15

    A novel boehmite/PVA composite membrane (BPCM) with remarkably enhanced adsorption performance towards Cr(VI) was successfully synthesized from Al(NO3)3·9H2O using HAc as the peptizing agent via a facile sol-gel method. The physicochemical properties of the BPCM, the boehmite powder (BP) without PVA and a commercial boehmite powder (CBP) were comparatively characterized by XRD, TGA-DSC, FT-IR and XPS. Batch adsorption experiments showed that the adsorption performance of the BPCM is much better than those of BP and CBP. Its adsorption process was well described by the pseudo-second-order kinetic model, and its equilibrium data fit the Langmuir isotherm well with a maximum adsorption capacity of 36.41mgg(-1). Its interference adsorption experiment in presence of coexisting anions showed that SO4(2-) and HPO4(2-) have greater effect than those of the Cl(-), F(-), C2O4(2-) and HCO3(-). A three step action mechanism including adsorption of Cr(VI) anions, complexation between Cr(VI) anions and the functional groups on the surface of BPCM, and the reduction of Cr(VI) to Cr(III) was proposed to illustrate the adsorption process. This efficient film could be easily separated after adsorption, exhibiting great potential for the removal of Cr(VI) from aqueous solution, and other fields of environmental remediation. PMID:27450337

  14. Kinetics and Thermodynamics of Reserpine Adsorption onto Strong Acidic Cationic Exchange Fiber

    PubMed Central

    Guo, Zhanjing; Liu, Xiongmin; Huang, Hongmiao

    2015-01-01

    The kinetics and thermodynamics of the adsorption process of reserpine adsorbed onto the strong acidic cationic exchange fiber (SACEF) were studied by batch adsorption experiments. The adsorption capacity strongly depended on pH values, and the optimum reserpine adsorption onto the SACEF occurred at pH = 5 of reserpine solution. With the increase of temperature and initial concentration, the adsorption capacity increased. The equilibrium was attained within 20 mins. The adsorption process could be better described by the pseudo-second-order model and the Freundlich isotherm model. The calculated activation energy Ea was 4.35 kJ/mol. And the thermodynamic parameters were: 4.97<ΔH<7.44 kJ/mol, -15.29<ΔG<-11.87 kJ/mol and 41.97<ΔS<47.35 J/mol·K. The thermodynamic parameters demonstrated that the adsorption was an endothermic, spontaneous and feasible process of physisorption within the temperature range between 283 K and 323 K and the initial concentration range between 100 mg/L and 300 mg/L. All the results showed that the SACEF had a good adsorption performance for the adsorption of reserpine from alcoholic solution. PMID:26422265

  15. Glyphosate and AMPA adsorption in soils: laboratory experiments and pedotransfer rules.

    PubMed

    Sidoli, Pauline; Baran, Nicole; Angulo-Jaramillo, Rafael

    2016-03-01

    Adsorption of the herbicide glyphosate and its main metabolite AMPA (aminomethylphosphonic acid) was investigated on 17 different agricultural soils. Batch equilibration adsorption data are shown by Freundlich adsorption isotherms. Glyphosate adsorption is clearly affected by equilibration concentrations, but the nonlinear AMPA adsorption isotherms indicate saturation of the adsorption sites with increasing equilibrium concentrations. pHCaCl2 (i.e. experimental pH) is the major parameter governing glyphosate and AMPA adsorption in soils. However, considering pHCaCl2 values, available phosphate amount, and amorphous iron and aluminium oxide contents by using a nonlinear multiple regression equation, obtains the most accurate and powerful pedotransfer rule for predicting the adsorption constants for these two molecules. As amorphous iron and aluminium oxide contents in soil are not systematically determined, we also propose a pedotransfer rule with two variables-pHCaCl2 values and available phosphate amount-that remains acceptable for both molecules. Moreover, the use of the commonly measured pHwater or pHKCl values gives less accurate results compared to pHCaCl2 measurements. To our knowledge, this study is the first AMPA adsorption characterization for a significant number of temperate climate soils. PMID:26581693

  16. Features of the adsorption of naproxen enantiomers on weak chiral anion-exchangers in nonlinear chromatography

    SciTech Connect

    Asnin, Leonid; Kaczmarski, Krzysztof; Guiochon, Georges A

    2008-01-01

    The retention mechanism of the enantiomers of naproxen on a Pirkle-type chiral stationary phase (CSP) was studied. This CSP is made of a porous silica grafted with quinidine carbamate. It can interact with the weak organic electrolyte naproxen either by adsorbing it or by ion-exchange. Using frontal chromatography, we explored the adsorption equilibrium under such experimental conditions that naproxen dissociates or cannot dissociate. Under conditions preventing ionic dissociation, the adsorption isotherms were measured, the adsorption energy distributions determined, and the chromatographic profiles calculated. Three different types of the adsorption sites were found for both enantiomers. The density and the binding energy of these sites depend on the nature of the organic modifier. Different solute species, anions, neutral molecules, solvent-ion associates, and solute dimers can coexist in solution, giving rise to different forms of adsorption. This study showed the unexpected occurrence of secondary steps in the breakthrough profiles of S-naproxen in the adsorption mode at high concentrations. Being enantioselective, this phenomenon was assumed to result from the association of solute molecules involving a chiral selector moiety. A multisite Langmuir adsorption model was used to calculate band profiles. Although this model accounts excellently for the experimental adsorption isotherms, it does not explain all the features of the breakthrough profiles. A comparison between the calculated and experimental profiles allowed useful conclusions concerning the effects of the adsorbate-adsorbate and adsorbate-solvent interactions on the adsorption mechanism.

  17. Modeling high adsorption capacity and kinetics of organic macromolecules on super-powdered activated carbon.

    PubMed

    Matsui, Yoshihiko; Ando, Naoya; Yoshida, Tomoaki; Kurotobi, Ryuji; Matsushita, Taku; Ohno, Koichi

    2011-02-01

    The capacity to adsorb natural organic matter (NOM) and polystyrene sulfonates (PSSs) on small particle-size activated carbon (super-powdered activated carbon, SPAC) is higher than that on larger particle-size activated carbon (powdered-activated carbon, PAC). Increased adsorption capacity is likely attributable to the larger external surface area because the NOM and PSS molecules do not completely penetrate the adsorbent particle; they preferentially adsorb near the outer surface of the particle. In this study, we propose a new isotherm equation, the Shell Adsorption Model (SAM), to explain the higher adsorption capacity on smaller adsorbent particles and to describe quantitatively adsorption isotherms of activated carbons of different particle sizes: PAC and SPAC. The SAM was verified with the experimental data of PSS adsorption kinetics as well as equilibrium. SAM successfully characterized PSS adsorption isotherm data for SPACs and PAC simultaneously with the same model parameters. When SAM was incorporated into an adsorption kinetic model, kinetic decay curves for PSSs adsorbing onto activated carbons of different particle sizes could be simultaneously described with a single kinetics parameter value. On the other hand, when SAM was not incorporated into such an adsorption kinetic model and instead isotherms were described by the Freundlich model, the kinetic decay curves were not well described. The success of the SAM further supports the adsorption mechanism of PSSs preferentially adsorbing near the outer surface of activated carbon particles. PMID:21172719

  18. Simultaneous adsorption of Cd²⁺ and BPA on amphoteric surfactant activated montmorillonite.

    PubMed

    Liu, Chongmin; Wu, Pingxiao; Zhu, Yajie; Tran, Lytuong

    2016-02-01

    The study mainly investigated the simultaneous adsorption of bisphenol A (BPA) and Cd(2+) from aqueous solution on octadecane-betaine modified montmorillonite (BS-Mt). The characteristics of the obtained materials were analyzed by X-ray diffraction (XRD), Fourier-transform infrared (FTIR), Specific surface area (BET) and Scanning electron microscopy/Energy disperse spectroscopy (SEM/EDS), confirming that BS-18 was successfully introduced into Mt. Also, factors including initial solution pH, initial Cd(2+)/BPA concentration, contact time and adsorbent dosage on the adsorption processes were shown to be crucial for Cd(2+) adsorption, whereas had negligible effects on BPA adsorption. In this study, we found that pseudo-second-order model fitted well with the adsorption kinetic studies for both Cd(2+) and BPA with an equilibrium time of 24 h. The Cd(2+) and BPA adsorption isotherm could be well described by Freundlich model and Langmuir model, respectively. On the basis of kinetic models, the maximum adsorption capacity of Cd(2+) in aqueous solution was slightly enhanced after modification, indicating that Cd(2+) adsorption on BS-Mt was mainly attributed to direct electrostatic attraction and the chelate reaction, while the dramatic enhancement of maximum adsorption capacity for BPA was due to the hydrophobic interaction. PMID:26451652

  19. Adsorptive removal of phenol from aqueous solution with zeolitic imidazolate framework-67.

    PubMed

    Pan, Yong; Li, Zhi; Zhang, Zhe; Tong, Xiong-Shi; Li, Hai; Jia, Chong-Zhi; Liu, Bei; Sun, Chang-Yu; Yang, Lan-Ying; Chen, Guang-Jin; Ma, De-Yun

    2016-03-15

    ZIF-67(zinc-methylimidazolate framework-67), one of the zeolitic imidazolate frameworks (ZIFs), was used for the removal of phenol from aqueous solutions via adsorption and shows high adsorption capacity for phenol. The thermodynamic and kinetic adsorption behavior of ZIF-67 for phenol in water with concentration ranging from 50 to 300 ppm were investigated in a batch reactor and a ZIF-67 packed column, respectively. The effects of pH, contact time, zeta potential of the adsorbent and temperature on the adsorption behavior were evaluated, and the results demonstrated that the adsorption is primarily brought about by a specific favorable interaction (electrostatic interaction) between phenol and ZIF-67 surface. The suitability of the Langmuir adsorption model to the equilibrium data was investigated for each phenol-adsorbent system, which the results showed that the equilibrium data for all the phenol-sorbent systems fitted the Langmuir model. Thermodynamic parameters such as Gibbs free energy are calculated from the experimental data at different temperatures. The adsorbent could be perfectly regenerated at 120 °C with little loss in the adsorption ability. PMID:26745178

  20. Application of surface complexation models to anion adsorption by natural materials.

    PubMed

    Goldberg, Sabine

    2014-10-01

    Various chemical models of ion adsorption are presented and discussed. Chemical models, such as surface complexation models, provide a molecular description of anion adsorption reactions using an equilibrium approach. Two such models, the constant capacitance model and the triple layer model, are described in the present study. Characteristics common to all the surface complexation models are equilibrium constant expressions, mass and charge balances, and surface activity coefficient electrostatic potential terms. Methods for determining parameter values for surface site density, capacitances, and surface complexation constants also are discussed. Spectroscopic experimental methods of establishing ion adsorption mechanisms include vibrational spectroscopy, nuclear magnetic resonance spectroscopy, electron spin resonance spectroscopy, X-ray absorption spectroscopy, and X-ray reflectivity. Experimental determinations of point of zero charge shifts and ionic strength dependence of adsorption results and molecular modeling calculations also can be used to deduce adsorption mechanisms. Applications of the surface complexation models to heterogeneous natural materials, such as soils, using the component additivity and the generalized composite approaches are described. Emphasis is on the generalized composite approach for predicting anion adsorption by soils. Continuing research is needed to develop consistent and realistic protocols for describing ion adsorption reactions on soil minerals and soils. The availability of standardized model parameter databases for use in chemical speciation-transport models is critical. PMID:24619924

  1. Quantum Monte Carlo investigations of adsorption energetics on graphene.

    PubMed

    Hsing, C R; Wei, C M; Chou, M Y

    2012-10-01

    We have performed calculations of adsorption energetics on the graphene surface using the state-of-the-art diffusion quantum Monte Carlo method. Two types of configurations are considered in this work: the adsorption of a single O, F, or H atom on the graphene surface and the H-saturated graphene system (graphane). The adsorption energies are compared with those obtained from density functional theory with various exchange-correlation functionals. The results indicate that the approximate exchange-correlation functionals significantly overestimate the binding of O and F atoms on graphene, although the preferred adsorption sites are consistent. The energy errors are much less for atomic hydrogen adsorbed on the surface. We also find that a single O or H atom on graphene has a higher energy than in the molecular state, while the adsorption of a single F atom is preferred over the gas phase. In addition, the energetics of graphane is reported. The calculated equilibrium lattice constant turns out to be larger than that of graphene, at variance with a recent experimental suggestion. PMID:22909778

  2. [Adsorption of methylene blue onto vanadium-doped magnetite].

    PubMed

    Zhong, Yuan-Hong; Liang, Xiao-Liang; Zhu, Jian-Xi; He, Hong-Ping; Yuan, Peng

    2010-06-01

    A series of vanadium-doped magnetite (Fe3-x VxO4, x < 0.4) synthesized by an oxidation-precipitation method, were characterized using chemical analysis, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), as well as thermogravimetric and differential scanning calorimetry (TG-DSC) analyses. The obtained results show that the synthetic Fe3-x VxO4 has spinel structure while vanadium mostly replaces Fe3+ in the octahedral sites. The synthetic Fe3-x VxO4 is magnetic material, with crystal size ranging from 28 to 35 nm. The substitution of vanadium in the magnetite structure increases the amount of surface hydroxyls. The experimental adsorption results indicate that, in neutral pH condition, the maximum adsorption capacities of Fe3-x VxO4 increase obviously with the increase of vanadium concentration in magnetite while the adsorption isotherm complies well with the Langmuir model. The adsorption of methylene blue (MB) on Fe3-x VxO4 can get equilibrium in the first 25 min, supporting a pseudo-second order equation. Moreover, the rise of the solution pH value results in an increase of the adsorption capability of MB on Fe3-x VxO4. PMID:20698274

  3. Immobilization of Acetobacter aceti on cellulose ion exchangers: adsorption isotherms

    SciTech Connect

    Bar, R.; Gainer, J.L.; Kirwan, D.J.

    1986-08-01

    The adsorptive behavior of cells of Acetobacter aceti, ATCC 23746, on DEAE-, TEAE-, and DEHPAE-cellulose ion exchangers in a modified Hoyer's medium at 30 degrees Centigrade was investigated. The maximum observed adsorption capacities varied from 46 to 64 mg dry wt/g resin. The Langmuir isotherm form was used to fit the data, since the cells formed a monolayer on the resin and exhibited saturation. The equilibrium constant in the Langmuir expression was qualitatively correlated with the surface charge density of the resin. The adsorption was also ''normalized'' by considering the ionic capacities of the resins. The exceptionally high normalized adsorption capacity of ECTEOLA-cellulose, 261 mg dry/meq, may be explained by an interaction between the cell wall and the polyglyceryl chains of the exchanging groups in addition to the electrostatic effects. The effect of pH on the bacterial adsorption capacity of ECTEOLA-, TEAE-, and phosphate-cellulose resins was studied and the pH of the bacteria was estimated to be 3.0. 17 references.

  4. Liquid Phase Adsorption of α-Tocopherol by Activated Carbon

    NASA Astrophysics Data System (ADS)

    Bono, Awang; Ming, Chu Chi; Sundang, Murni

    α-Tocopherol or commonly called vitamin E can be found in major commercial vegetable oils such as soya oil and palm oil. However the existence in these oil is in low concentration. The recovery of low concentration of α-tocopherol from palm oils is increasingly popular. Adsorption technique for the recovery of α-tocopherol from palm oil is believed to be much lower in cost and more effective. As a case study in this work, activated carbon is chosen as the adsorbent and ethanol as the solvent. The adsorption equilibria of α-tocopherol onto activated carbon was conducted in batch and the concentration of α-tocopherol was identified by LCMS. Langmuirian monolayer adsorption theory was used for the analysis of the isotherm equilibria. The adsorptivity of α-tocopherol onto activated carbon was identified. The adsorption equilibria at low concentration found to be linear. The breakthrough curve was then generated using model assuming isothermal, single transition trace component with intraparticle diffusion. Sensitivity test on the curve indicated that the system is very sensitive to changes in diffusitivity and passive to changes on the equilibrium constant.

  5. The mechanism of Zn sup 2+ adsorption on calcite

    SciTech Connect

    Zachara, J.M. ); Kittrick, J.A.; Harsh, J.B. )

    1988-09-01

    The adsorption of Zn{sup 2+} on calcite (CaCO{sub 3(s)}) was investigated from aqueous solutions in equilibrium with CaCO{sub 3(s)} and undersaturated with respect to Zn{sub 5}(OH){sub 6}(CO{sub 3}){sub 2(s)}. Zinc adsorption occurred via exchange with Ca{sub 2+} in a surface-adsorbed layer on calcite. The validity of this exchange reaction was supported by adsorption isotherm and constant concentration experiments, where Ca{sup 2+}{sub aq} was varied by systematically changing the pH and CO{sub 2(g)}. Greater adsorption of Zn{sup 2+} occurred at higher pH and Co{sub 2(g)} levels, where Ca{sup 2+} activities were lowest. Sites available for Zn{sup 2+} sorption were less than 10% of Ca{sup 2+} sites on the calcite surface. Surface exchange of Zn{sup 2+} did not affect the solubility of calcite. Zinc sorption was apparently independent of surface charge, which suggested that the surface complex had covalent character. Desorption and isotopic exchange experiments indicated that the surface complex remained hydrated and labile as Zn{sup 2+} was rapidly exchangeable with Ca{sup 2+}. Careful analysis of the adsorption data showed that Zn{sup 2+} and ZnOH{sup +} were the sorbing species.

  6. Molecular structure-adsorption study on current textile dyes.

    PubMed

    Örücü, E; Tugcu, G; Saçan, M T

    2014-01-01

    This study was performed to investigate the adsorption of a diverse set of textile dyes onto granulated activated carbon (GAC). The adsorption experiments were carried out in a batch system. The Langmuir and Freundlich isotherm models were applied to experimental data and the isotherm constants were calculated for 33 anthraquinone and azo dyes. The adsorption equilibrium data fitted more adequately to the Langmuir isotherm model than the Freundlich isotherm model. Added to a qualitative analysis of experimental results, multiple linear regression (MLR), support vector regression (SVR) and back propagation neural network (BPNN) methods were used to develop quantitative structure-property relationship (QSPR) models with the novel adsorption data. The data were divided randomly into training and test sets. The predictive ability of all models was evaluated using the test set. Descriptors were selected with a genetic algorithm (GA) using QSARINS software. Results related to QSPR models on the adsorption capacity of GAC showed that molecular structure of dyes was represented by ionization potential based on two-dimensional topological distances, chromophoric features and a property filter index. Comparison of the performance of the models demonstrated the superiority of the BPNN over GA-MLR and SVR models. PMID:25529487

  7. KOH catalysed preparation of activated carbon aerogels for dye adsorption.

    PubMed

    Ling, Sie King; Tian, H Y; Wang, Shaobin; Rufford, Thomas; Zhu, Z H; Buckley, C E

    2011-05-01

    Organic carbon aerogels (CAs) were prepared by a sol-gel method from polymerisation of resorcinol, furfural, and hexamethylenetetramine catalysed by KOH at around pH 9 using ambient pressure drying. The effect of KOH in the sol-gel on CA synthesis was studied. It was found that addition of KOH prior to the sol-gel polymerisation process improved thermal stability of the gel, prevented the crystallinity of the gel to graphite, increased the microporosity of CA and promoted activation of CA. The CAs prepared using the KOH catalyst exhibited higher porosity than uncatalysed prepared samples. Activation in CO(2) at higher temperature also enhanced the porosity of CAs. Adsorption tests indicated that the CAs were effective for both basic and acid dye adsorption and the adsorption increased with increasing surface area and pore volume. The kinetic adsorption of dyes was diffusion control and could be described by the second-order kinetic model. The equilibrium adsorption of dyes was higher than activated carbon. PMID:21345448

  8. Adsorption of sugar beet herbicides to Finnish soils.

    PubMed

    Autio, Sari; Siimes, Katri; Laitinen, Pirkko; Rämö, Sari; Oinonen, Seija; Eronen, Liisa

    2004-04-01

    Three sugar beet herbicides, ethofumesate, phenmedipham and metamitron, are currently used on conventional sugar beet cultivation, while new varieties of herbicide resistant (HR) sugar beet, tolerant of glyphosate or glufosinate-ammonium, are under field testing in Finland. Little knowledge has so far been available on the adsorption of these herbicides to Finnish soils. The adsorption of these five herbicides was studied using the batch equilibrium method in 21 soil samples collected from different depths. Soil properties like organic carbon content, texture, pH and partly the phosphorus and oxide content of the soils were tested against the adsorption coefficients of the herbicides. In general, the herbicides studied could be arranged according to their adsorption coefficients as follows: glyphosate>phenmedipham>ethofumesate approximately glufosinate-ammonium>metamitron, metamitron meaning the highest risk of leaching. None of the measured soil parameters could alone explain the adsorption mechanism of these five herbicides. The results can be used in model assessments of risk for leaching to ground water resulting from weed control of sugar beet in Finland. PMID:14761694

  9. Adsorption of ciprofloxacin on surface-modified carbon materials.

    PubMed

    Carabineiro, S A C; Thavorn-Amornsri, T; Pereira, M F R; Figueiredo, J L

    2011-10-01

    The adsorption capacity of ciprofloxacin (CPX) was determined on three types of carbon-based materials: activated carbon (commercial sample), carbon nanotubes (commercial multi-walled carbon nanotubes) and carbon xerogel (prepared by the resorcinol/formaldehyde approach at pH 6.0). These materials were used as received/prepared and functionalised through oxidation with nitric acid. The oxidised materials were then heat treated under inert atmosphere (N2) at different temperatures (between 350 and 900°C). The obtained samples were characterised by adsorption of N2 at -196 °C, determination of the point of zero charge and by temperature programmed desorption. High adsorption capacities ranging from approximately 60 to 300 mgCPxgC(-1) were obtained (for oxidised carbon xerogel, and oxidised thermally treated activated carbon Norit ROX 8.0, respectively). In general, it was found that the nitric acid treatment of samples has a detrimental effect in adsorption capacity, whereas thermal treatments, especially at 900 °C after oxidation, enhance adsorption performance. This is due to the positive effect of the surface basicity. The kinetic curves obtained were fitted using 1st or 2nd order models, and the Langmuir and Freundlich models were used to describe the equilibrium isotherms obtained. The 2nd order and the Langmuir models, respectively, were shown to present the best fittings. PMID:21733541

  10. Adsorption of divalent copper, zinc, cadmium and lead ions from aqueous solution by waste tea and coffee adsorbents.

    PubMed

    Djati Utomo, H; Hunter, K A

    2006-01-01

    The adsorption of the divalent cations of Cu, Zn, Cd and Pb by tea leaves and coffee grounds from aqueous solutions is described. Both adsorbents exhibited strong affinity for these ions which could be described by a simple single-site equilibrium model. For coffee, the order of increasing adsorption equilibrium constant K was Cu < Pb < Zn < Cd, while for tea the opposite order was observed indicating that the adsorption sites on each adsorbent have a different chemical nature. Adsorption decreased at low pH < 4 through competition with H+ for adsorption sites, and for all metals except Cu, at high pH > 10, probably because of anion formation in the case of Zn2+ and also increased leaching of metal-binding soluble materials. The effect of metal ion concentration on the adsorptive equilibria indicated a threshold concentration above which overall adsorption became limited by saturation of the adsorption sites. Competition between two metal ions for the same sites was not observed with Cu(II) and Pb(II), however Zn(II) reacted competitively with Cd(II) binding sites on both tea and coffee. If fresh coffee or tea adsorbents were used, the fraction of metal ion taken up by the adsorbent was diminished by the competitive effects of soluble metal-binding ligands released by the tea or coffee. Experiments with coffee showed that roasting temperature controls the formation of metal ion adsorption sites for this adsorbent. PMID:16457172

  11. Equilibrium and Orientation in Cephalopods.

    ERIC Educational Resources Information Center

    Budelmann, Bernd-Ulrich

    1980-01-01

    Describes the structure of the equilibrium receptor system in cephalopods, comparing it to the vertebrate counterpart--the vestibular system. Relates the evolution of this complex system to the competition of cephalopods with fishes. (CS)

  12. Equilibrium Constants You Can Smell.

    ERIC Educational Resources Information Center

    Anderson, Michael; Buckley, Amy

    1996-01-01

    Presents a simple experiment involving the sense of smell that students can accomplish during a lecture. Illustrates the important concepts of equilibrium along with the acid/base properties of various ions. (JRH)

  13. Comparison of equilibrium and non-equilibrium distribution coefficients for the human drug carbamazepine in soil.

    PubMed

    Williams, C F; Watson, J E; Nelson, S D

    2014-01-01

    The distribution coefficient (KD) for the human drug carbamazepine was measured using a non-equilibrium technique. Repacked soil columns were prepared using an Airport silt loam (Typic Natrustalf) with an average organic matter content of 2.45%. Carbamazepine solutions were then leached through the columns at 0.5, 1.0 and 1.5 mL min(-1) representing average linear velocities of 1.8, 3.5 and 5.3 cm h(-1) respectively. Each flow rate was replicated three times and three carbamazepine pulses were applied to each column resulting in a total of 9 columns with 27 total carbamazepine pulses. Breakthrough curves were used to determine KD using the parameter fitting software CXTFIT. Results indicate that as flow rate decreased from 5.3 to 1.8 cm h(-1), KD increased an average of 21%. Additionally, KD determined by column leaching (14.7-22.7 L kg(-1)) was greater than KD determined by a 2h batch equilibrium adsorption (12.6 L kg(-1)). Based on these KD's carbamazepine would be generally characterized as non-mobile in the soil investigated. However, repeated carbamazepine applications resulted in an average 22% decrease in KD between the first and third applications. Decreasing KD is attributed to differences in sorption site kinetics and carbamazepine residence time in contact with the soil. This would indicate that the repeated use of reclaimed wastewater at high application rates for long-term irrigation or groundwater recharge has the potential to lead to greater transport of carbamazepine than KD determined by batch equilibrium would predict. PMID:24050717

  14. Adsorption of metal ions onto Moroccan stevensite: kinetic and isotherm studies.

    PubMed

    Benhammou, A; Yaacoubi, A; Nibou, L; Tanouti, B

    2005-02-15

    The aim of this paper is to study the adsorption of the heavy metals (Cd(II), Cu(II), Mn(II), Pb(II), and Zn(II)) from aqueous solutions by a natural Moroccan stevensite called locally rhassoul. We carried out, first, a mineralogical and physicochemical characterization of stevensite. The surface area is 134 m2/g and the cation exchange capacity (CEC) is 76.5 meq/100 g. The chemical formula of stevensite is Si3.78Al0.22Mg2.92Fe0.09Na0.08K0.08O10(OH)2.4H2O. Adsorption tests of Cd(II), Cu(II), Mn(II), Pb(II), and Zn(II) in batch reactors were carried out at ambient temperature and at constant pH. Two simplified models including pseudo-first-order and pseudo-second- order were used to test the adsorption kinetics. The equilibrium time and adsorption rate of adsorption were determined. The increasing order of the adsorption rates follows the sequence Mn(II) > Pb(II) > Zn(II) > Cu(II) > Cd(II). The Dubinin-Radushkevich (D-R), Langmuir, and Redlich-Peterson (R-P) models were adopted to describe the adsorption isotherms. The maximal adsorption capacities at pH 4.0 determined from the D-R and Langmuir models vary in the following order: Cu(II) > Mn(II) > Cd(II) > Zn(II) > Pb(II). The equilibrium data fitted well with the three-parameter Redlich-Peterson model. The values of mean energy of adsorption show mainly an ion-exchange mechanism. Also, the influence of solution pH on the adsorption onto stevensite was studied in the pH range 1.5-7.0. PMID:15589536

  15. Metal adsorption by agricultural biosorbents: Adsorption isotherm, kinetic and biosorbents chemical structures.

    PubMed

    Sadeek, Sadeek A; Negm, Nabel A; Hefni, Hassan H H; Wahab, Mostafa M Abdel

    2015-11-01

    Biosorption of Cu(II), Co(II) and Fe(III) ions from aqueous solutions by rice husk, palm leaf and water hyacinth was investigated as a function of initial pH, initial heavy metal ions concentration and treatment time. The adsorption process was examined by two adsorption isotherms: Langmuir and Freundlich isotherms. The experimental data of biosorption process were analyzed using pseudo-first order, pseudo-second order kinetic models. The equilibrium biosorption isotherms showed that the three studied biosorbents possess high affinity and sorption capacity for Cu(II), Co(II) and Fe(III) ions. Rice husk showed more efficiency than palm leaf and water hyacinth. Adsorption of Cu(II) and Co(II) was more efficient in alkaline medium (pH 9) than neutral medium due to the high solubility of metal ion complexes. The metal removal efficiency of each biosorbent was correlated to its chemical structure. DTA studies showed formation of metal complex between the biosorbents and the metal ions. The obtained results showed that the tested biosorbents are efficient and alternate low-cost biosorbent for removal of heavy metal ions from aqueous media. PMID:26282929

  16. Edge equilibrium code for tokamaks

    SciTech Connect

    Li, Xujing; Drozdov, Vladimir V.

    2014-01-15

    The edge equilibrium code (EEC) described in this paper is developed for simulations of the near edge plasma using the finite element method. It solves the Grad-Shafranov equation in toroidal coordinate and uses adaptive grids aligned with magnetic field lines. Hermite finite elements are chosen for the numerical scheme. A fast Newton scheme which is the same as implemented in the equilibrium and stability code (ESC) is applied here to adjust the grids.

  17. A search for equilibrium states

    NASA Technical Reports Server (NTRS)

    Zeleznik, F. J.

    1982-01-01

    An efficient search algorithm is described for the location of equilibrium states in a search set of states which differ from one another only by the choice of pure phases. The algorithm has three important characteristics: (1) it ignores states which have little prospect for being an improved approximation to the true equilibrium state; (2) it avoids states which lead to singular iteration equations; (3) it furnishes a search history which can provide clues to alternative search paths.

  18. Characterization and adsorption of Lactobacillus virulent phage P1.

    PubMed

    Chen, X; Xi, Y; Zhang, H; Wang, Z; Fan, M; Liu, Y; Wu, W

    2016-09-01

    Bacteriophage infection of lactic acid bacteria is considered an important problem worldwide in the food fermentation industry, as it may produce low quality or unsafe foods, cause fermentation failure, and result in economic losses. To increase current knowledge on the properties of Lactobacillus virulent phages, we evaluated the effect of divalent cations, temperature, pH, and chloramphenicol on the adsorption ability of Lactobacillus virulent phage P1. Phage P1 was isolated from the abnormal fermentation liquid of Lactobacillus plantarum IMAU10120. The results showed that this phage belonged to the Siphoviridae family. The latent period of this phage was 45min, and the burst time was 90min. Burst size was 132.88±2.37 phage counts expressed per milliliter per infective center. This phage showed good tolerance at different temperatures, but incubation at 50°C only affected its adsorption. Adsorption rate reached a maximum value between 30 and 42°C. A high adsorption value of phage infectivity was obtained from pH 6 to 8. Moreover, calcium ions promoted and increased the adsorption capacity of phage P1, but magnesium ions had negative effects. Chloramphenicol had no effect on phage adsorption. This study increased current knowledge on the characterization and biological aspects of Lactobacillus virulent phages, and may provide some basic information that can be used to design successful antiphage strategies in the food industry. PMID:27372579

  19. Reservoir capacity estimates in shale plays based on experimental adsorption data

    NASA Astrophysics Data System (ADS)

    Ngo, Tan

    from different measurement techniques using representative fluids (such as CH4 and CO2) at elevated pressures, and the adsorbed density can range anywhere between the liquid and the solid state of the adsorbate. Whether these discrepancies are associated with the inherent heterogeneity of mudrocks and/or with poor data quality requires more experiments under well-controlled conditions. Nevertheless, it has been found in this study that methane GIP estimates can vary between 10-45% and 10-30%, respectively, depending on whether the free or the total amount of gas is considered. Accordingly, CO2 storage estimates range between 30-90% and 15-50%, due to the larger adsorption capacity and gas density at similar pressure and temperature conditions. A manometric system has been designed and built that allows measuring the adsorption of supercritical fluids in microporous materials. Preliminary adsorption tests have been performed using a microporous 13X zeolite and CO 2 as an adsorbing gas at a temperature of 25oC and 35oC and at pressures up to 500 psi. Under these conditions, adsorption is quantified with a precision of +/- 3%. However, relative differences up to 15-20% have been observed with respect to data published in the literature on the same adsorbent and at similar experimental conditions. While it cannot be fully explained with uncertainty analysis, this discrepancy can be reduced by improving experiment practice, thus including the application of a higher adsorbent's regeneration temperature, of longer equilibrium times and of a careful flushing of the system between the various experimental steps. Based on the results on 13X zeolite, virtual tests have been conducted to predict the performance of the manometric system to measure adsorption on less adsorbing materials, such as mudrocks. The results show that uncertainties in the estimated adsorbed amount are much more significant in shale material and they increase with increasing pressure. In fact, relative

  20. Removal of tetracycline from wastewater using pumice stone: equilibrium, kinetic and thermodynamic studies.

    PubMed

    Guler, Ulker Asli; Sarioglu, Meltem

    2014-01-01

    In this study, pumice stone was used for the removal of tetracyline (TC) from aqueous solutions. It was characterized by XRD, FT-IR, SEM and BET analyses. Cation exchange capacity of pumice stone was found to be 9.9 meq/100 g. Effect of various parameters such as solution pH (2-11), adsorbent dosage (0.5-10 g/L), contact time (2.5-120 min), initial TC concentration (5-300 mg/L) and temperature (20-50°C) on TC adsorption onto pumice was investigated. Also the adsorption of TC on pumice stone was studied as a function of Na(+) and Cu(2+) cations changing pH from 2 to 11 using batch experiments. The best removal efficiency performance was exhibited at adsorbent dosage 10 g/L, pH 3, contact time 120 min. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models were applied to the equilibrium data. The result has shown that the adsorption was favorable, physicochemical in nature and agrees well with Langmuir and Freundlich models. The maximum Langmuir adsorption capacity was found to be 20.02 mg/g. The adsorption behavior of TC on pumices stone was fitted well in the pseudo-second order kinetics model. Thermodynamic parameters calculated from the adsorption data at different temperature showed that the adsorption reaction was feasible, spontaneous and exothermic. PMID:24936305

  1. Removal of tetracycline from wastewater using pumice stone: equilibrium, kinetic and thermodynamic studies

    PubMed Central

    2014-01-01

    In this study, pumice stone was used for the removal of tetracyline (TC) from aqueous solutions. It was characterized by XRD, FT-IR, SEM and BET analyses. Cation exchange capacity of pumice stone was found to be 9.9 meq/100 g. Effect of various parameters such as solution pH (2–11), adsorbent dosage (0.5-10 g/L), contact time (2.5-120 min), initial TC concentration (5–300 mg/L) and temperature (20–50°C) on TC adsorption onto pumice was investigated. Also the adsorption of TC on pumice stone was studied as a function of Na+ and Cu2+ cations changing pH from 2 to 11 using batch experiments. The best removal efficiency performance was exhibited at adsorbent dosage 10 g/L, pH 3, contact time 120 min. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models were applied to the equilibrium data. The result has shown that the adsorption was favorable, physicochemical in nature and agrees well with Langmuir and Freundlich models. The maximum Langmuir adsorption capacity was found to be 20.02 mg/g. The adsorption behavior of TC on pumices stone was fitted well in the pseudo-second order kinetics model. Thermodynamic parameters calculated from the adsorption data at different temperature showed that the adsorption reaction was feasible, spontaneous and exothermic. PMID:24936305

  2. Visualization of an adsorption model for surfactant transport from micelle solutions to a clean air/water interface using fluorescence microscopy.

    PubMed

    Song, Qing; Yuan, Mingjun

    2011-05-01

    This work pertains to visualizing a transport model for adsorption of surfactants from micelle solutions onto a clean air/water interface. Under the condition of surfactant adsorption from very dilute solutions, the time scale for diffusion of a surfactant monomer is much slower than the time scale for kinetic breakdown of the aggregates. A theoretical model predicts two regimes for the adsorption dynamics. We visualize these two regimes under the mechanism of solubilization using fluorescence microscopy, in which an insoluble fluorescent probe, NBD-HAD (4-(hexadecylamino)-7-nitrobenz-2-oxa-1,3-diazole), is used to illuminate the micelles. The dye fluoresces in the microenvironment of micelles but is quenched in the aqueous solution on laser excitation. The region containing micelles is illuminated, but the region which does not contain micelles appears dark. For surfactant solution of C(14)E(6) at concentration just above the critical micelle concentration (C(CMC)), C(CMC)=4.4 mg/L, a dark region between the bright image of the air/water interface and the micelle-containing zone is observed. This dark region becomes smaller with time and finally disappears once equilibrium is reached. For a surfactant solution of C(14)E(6) at the concentration of 4.74C(CMC), which is higher than a critical total surfactant concentration (C(T)(c)) of 4.25C(CMC), we observe bright images through surfactant solutions during the adsorption process. Fluorescence images validate the theoretical model. PMID:21349535

  3. A convection modified thermal equilibrium in near-critical fluids under microgravity conditions

    NASA Astrophysics Data System (ADS)

    Accary, G.; Raspo, I.; Bontoux, P.; Zappoli, B.

    As the vapor-liquid critical point is approached in zero-gravity, the time it takes for a near-critical fluid cell to reach thermal equilibrium approaches infinity, which necessitates long duration experiments in space. However in microgravity, the convection modifies the thermal equilibrium due to the high density and the hyper-compressibility of a near-critical fluid. Using three-dimensional direct numerical simulations, the aim of this study is to evaluate, in low-gravity conditions, the contribution of the residual convection in reaching the thermal equilibrium and in structuring the temperature field inside a differentially heated enclosure filled with a near-critical fluid.

  4. Adsorption of uranium(VI) and thorium(IV) by insolubilized humic acid from Ajloun soil - Jordan.

    PubMed

    Khalili, Fawwaz; Al-Banna, Ghadeer

    2015-08-01

    Humic acid from Ajloun soil has been extracted and insolubilized. The insolubilized humic acid (NaIHA) was characterized by Fourier transform infrared spectroscopy, elemental analysis, thermal gravimetric analysis, X-ray diffraction and differential scanning calorimetry. Adsorption of U(VI) and Th(IV) by NaIHA was studied using batch technique at different temperatures (25.0, 35.0 and 45.0 °C) and at different pH values (1.00, 2.00 and 3.00). It was found that NaIHA has higher uptake for Th(IV) than U(VI), and that the metal ion uptake by NaIHA increased with pH and reached a maximum at pH = 3. The kinetic studies were done, and showed that the equilibrium time for each metal ion occurs at 6 h to achieve maximum uptake level. Adsorption data were evaluated according to the Pseudo second-order reaction kinetic. The metal ions uptake properties by the NaIHA fit Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherms. Thermodynamic functions, ΔG°, ΔH° and ΔS° were determined for each metal ion. The positive values of ΔG° indicate that adsorption process is not highly favorable, while ΔH° values indicated that this process is endothermic. On the other hand, the process has positive entropy which means that the adsorption process increases the disorder of the system and it is entropy driven. Column experiments were used for the determination of metal ion loading capacity and desorption studies. The uptake capacities in column technique of U(VI) and Th(IV) ions are 2.63 and 4.85 mg metal ion/g NaIHA respectively. Recovery of U(VI) and Th(IV) ions was carried out by treatment of loaded insolubilized humic acid with 0.1 M and 1.0 M HNO3, the best recovery for U(VI) and Th(IV) ions were obtained when 1.0 M HNO3 was used. PMID:25890216

  5. The dynamic adsorption characteristics of phenol by granular activated carbon.

    PubMed

    Namane, A; Hellal, A

    2006-09-01

    The objective of the present work is to determine the operating conditions of an activated carbon filter, based on the characteristics of breakthrough curves. For this we apply the technical developed by Mickaels for the ionic exchange and applied by Luchkis for the adsorption, and which is the mass transfer zone. To reach our goal, an evaluation of the operating conditions (height of the bed, flow and concentration of effluent) on the characteristics of the mass transfer zone was made and an explanation of the mechanism of adsorption was given. Thereafter a modeling of the experimental results was done. PMID:16621251

  6. Dynamic sorption of ammonium by sandy soil in fixed bed columns: Evaluation of equilibrium and non-equilibrium transport processes.

    PubMed

    Jellali, S; Diamantopoulos, E; Kallali, H; Bennaceur, S; Anane, M; Jedidi, N

    2010-01-01

    The release of excess nitrogen-containing compounds into groundwater is a major concern in aquifer recharge by the Soil Aquifer Treatment (SAT) process. Ammonium (NH(4)(+)) is one of the most nocive and common nitrogen compounds in wastewaters. In order to assess the risk of wastewater use for aquifer recharge, NH(4)(+)adsorption onto Souhil wadi soil sampled from the SAT pilot plant (Nabeul, Tunisia) was studied using laboratory columns experiments. Several experiments were conducted using aqueous synthetic solutions under different aqueous ammonium concentrations and flow rates. Furthermore, a real wastewater solution was used to test the effect of competitive cations contents on NH(4)(+) adsorption. Afterwards, the Hydrus-1D model was used in inverse mode to simulate the ammonium transport through the Souhil wadi soil. For the synthetic solutions, the adsorbed ammonium amount varied from 1 to 30.7 mg kg(-1) for aqueous ammonium concentrations between 4.9 and 36.4 mg L(-1). The linear isotherm model was found to be the most suitable for describing this adsorption. The flow rate decrease from 45 to 15 mL min(-1) induced an increase in the ammonium adsorption capacity by 49%. Indeed, the lesser the flow rate is, the longer the residence time and the higher the exchange between the aqueous solution and soil matrix. The use of wastewater instead of aqueous synthetic solution decreased about 7 times the Souhil wadi adsorption capacity of ammonium because of its relatively high concentrations of competitive ions such as calcium and magnesium. The use of the Hydrus-1D model showed that the chemical non-equilibrium model was the best to simulate the ammonium transport through the laboratory soil columns. PMID:20034727

  7. Synthesis and adsorption performance of Mg(OH)2 hexagonal nanosheet-graphene oxide composites

    NASA Astrophysics Data System (ADS)

    Liu, Mengdi; Xu, Jing; Cheng, Bei; Ho, Wingkei; Yu, Jiaguo

    2015-03-01

    A series of Mg(OH)2 hexagonal nanosheet-graphene oxide (GO) composites were synthesized through a simple hydrothermal method using magnesium nitrate and GO as precursors, sodium nitrate and sodium oxalate as additives, and sodium hydroxide and ammonia as precipitants. The as-prepared samples were characterized by X-ray diffraction, nitrogen adsorption-desorption isotherms, Raman spectroscopy, zeta potential analysis, and scanning electron microscopy (SEM). The adsorption affinity of the as-prepared samples toward congo red (CR) in water was analyzed and investigated. Results indicated that GO addition influenced the thickness, morphology, and adsorption performance of Mg(OH)2 hexagonal nanosheets. As GO concentration increased, the thickness decreased. Especially at high GO concentration (1 wt%), Mg(OH)2 hexagonal nanosheets changed into aggregated flower-like spheres. Addition of small amounts of GO also increased the adsorption capacity of Mg(OH)2. The equilibrium adsorption data of CR on the composite were further investigated by Langmuir and Freundlich models, indicating that the Langmuir model was much more suitable for the experimental data. The sample prepared with 0.5 wt% GO showed the highest adsorption capacity with 118 mg g-1. The experimental data were then fitted using pseudo-second order kinetics, suggesting that pseudo-second order kinetics could well describe the adsorption of CR on composites. Adsorption thermodynamics analysis showed that the adsorption activation energy was 29.2 kJ mol-1, suggesting that the adsorption of CR onto the samples was physical adsorption. Adsorption between the samples and CR was mainly due to the strong electrostatic attraction between them because they had opposite charges. These findings indicated that Mg(OH)2-GO composite was an effective adsorbent for the removal of CR in water.

  8. Shape characteristics of equilibrium and non-equilibrium fractal clusters

    NASA Astrophysics Data System (ADS)

    Mansfield, Marc L.; Douglas, Jack F.

    2013-07-01

    It is often difficult in practice to discriminate between equilibrium and non-equilibrium nanoparticle or colloidal-particle clusters that form through aggregation in gas or solution phases. Scattering studies often permit the determination of an apparent fractal dimension, but both equilibrium and non-equilibrium clusters in three dimensions frequently have fractal dimensions near 2, so that it is often not possible to discriminate on the basis of this geometrical property. A survey of the anisotropy of a wide variety of polymeric structures (linear and ring random and self-avoiding random walks, percolation clusters, lattice animals, diffusion-limited aggregates, and Eden clusters) based on the principal components of both the radius of gyration and electric polarizability tensor indicates, perhaps counter-intuitively, that self-similar equilibrium clusters tend to be intrinsically anisotropic at all sizes, while non-equilibrium processes such as diffusion-limited aggregation or Eden growth tend to be isotropic in the large-mass limit, providing a potential means of discriminating these clusters experimentally if anisotropy could be determined along with the fractal dimension. Equilibrium polymer structures, such as flexible polymer chains, are normally self-similar due to the existence of only a single relevant length scale, and are thus anisotropic at all length scales, while non-equilibrium polymer structures that grow irreversibly in time eventually become isotropic if there is no difference in the average growth rates in different directions. There is apparently no proof of these general trends and little theoretical insight into what controls the universal anisotropy in equilibrium polymer structures of various kinds. This is an obvious topic of theoretical investigation, as well as a matter of practical interest. To address this general problem, we consider two experimentally accessible ratios, one between the hydrodynamic and gyration radii, the other

  9. Shape characteristics of equilibrium and non-equilibrium fractal clusters.

    PubMed

    Mansfield, Marc L; Douglas, Jack F

    2013-07-28

    It is often difficult in practice to discriminate between equilibrium and non-equilibrium nanoparticle or colloidal-particle clusters that form through aggregation in gas or solution phases. Scattering studies often permit the determination of an apparent fractal dimension, but both equilibrium and non-equilibrium clusters in three dimensions frequently have fractal dimensions near 2, so that it is often not possible to discriminate on the basis of this geometrical property. A survey of the anisotropy of a wide variety of polymeric structures (linear and ring random and self-avoiding random walks, percolation clusters, lattice animals, diffusion-limited aggregates, and Eden clusters) based on the principal components of both the radius of gyration and electric polarizability tensor indicates, perhaps counter-intuitively, that self-similar equilibrium clusters tend to be intrinsically anisotropic at all sizes, while non-equilibrium processes such as diffusion-limited aggregation or Eden growth tend to be isotropic in the large-mass limit, providing a potential means of discriminating these clusters experimentally if anisotropy could be determined along with the fractal dimension. Equilibrium polymer structures, such as flexible polymer chains, are normally self-similar due to the existence of only a single relevant length scale, and are thus anisotropic at all length scales, while non-equilibrium polymer structures that grow irreversibly in time eventually become isotropic if there is no difference in the average growth rates in different directions. There is apparently no proof of these general trends and little theoretical insight into what controls the universal anisotropy in equilibrium polymer structures of various kinds. This is an obvious topic of theoretical investigation, as well as a matter of practical interest. To address this general problem, we consider two experimentally accessible ratios, one between the hydrodynamic and gyration radii, the other

  10. Removal of boron from oilfield wastewater via adsorption with synthetic layered double hydroxides.

    PubMed

    Delazare, Thais; Ferreira, Letícia P; Ribeiro, Nielson F P; Souza, Mariana M V M; Campos, Juacyara C; Yokoyama, Lídia

    2014-01-01

    Hydrotalcite is a layered double hydroxide (LDH) consisting of brucite-like sheets of metal ions (Mg-Al). In this work, hydrotalcites were synthesized, and boron removal from oilfield wastewater was evaluated. LDHs were synthesized using the co-precipitation method. The calcined products (CLDHs) were obtained by heating at 500°C and characterized using X-ray diffraction, X-ray fluorescence, thermogravimetric analysis and the specific surface area (BET). The affinity of LDHs for borate ions was evaluated for calcined and uncalcined LDHs as a function of contact time, initial pH of the oilfield wastewater (pH ∼ 9) and the LDH surface area. The tests were conducted at room temperature (approximately 25ºC). The results indicated that 10 min were needed to reach a state of equilibrium during boron removal for calcined LDHs due to the high surface area (202.3 m(2) g(-1)) regardless of the initial pH of the oilfield wastewater, which resulted from the high buffering capacity of the LDHs. The adsorption capacity increased as the adsorbents levels increased for the range studied. After treatment of the oilfield wastewater containing 30 mg L(-1) of boron with Mg-Al-CO3-LDHs, the final concentration of boron was within the discharge limit set by current Brazilian environmental legislation, which is 5 mg L(-1). Pseudo-first-order and pseudo-second-order kinetic models were tested, and the latter was found to fit the experimental data better. Isotherms for boron adsorption by CLDHs were well described using the Langmuir and Freundlich equations. PMID:24766593

  11. Optimization of mesoporous carbons for efficient adsorption of berberine hydrochloride from aqueous solutions.

    PubMed

    Li, Yin; Fu, Jie; Deng, Shuguang; Lu, Xiuyang

    2014-06-15

    Sixteen mesoporous carbon adsorbents were synthesized by varying the ratio of soft to hard templates in order to optimize the pore textural properties of these adsorbents. The mesoporous carbon adsorbents have a high BET specific surface area (1590.3-2193.5 m(2)/g), large pore volume (1.72-2.56 cm(3)/g), and uniform pore size distribution with a median pore diameter ranging from 3.51 nm to 4.52 nm. It was observed that pore textural properties of the carbon adsorbents critically depend on the molar ratio of carbon sources to templates, and the hard template plays a more important role than the soft template in manipulating the pore textures. Adsorption isotherms of berberine hydrochloride at 303 K were measured to evaluate the adsorption efficacy of these adsorbents. The adsorption of berberine hydrochloride from aqueous solutions on the sixteen mesoporous carbon adsorbents synthesized in this work is very efficient, and the adsorption equilibrium capacities on all samples are more than double the adsorption capacities of berberine hydrochloride of the benchmark adsorbents (polymer resins and spherical activated carbons) at similar conditions. It was observed from the adsorption experiments that the equilibrium adsorption amounts of berberine hydrochloride are strongly correlated with the BET specific surface area and pore volume of the adsorbents. The adsorbent with the highest BET of 2193.5 m(2)/g displayed the largest adsorption capacity of 574 mg/g at an equilibrium concentration of 0.10mg/mL of berberine hydrochloride in an aqueous solution. PMID:24767505

  12. Arsenate adsorption mechanisms at the allophane - Water interface

    USGS Publications Warehouse

    Arai, Y.; Sparks, D.L.; Davis, J.A.

    2005-01-01

    We investigated arsenate (As(V)) reactivity and surface speciation on amorphous aluminosilicate mineral (synthetic allophane) surfaces using batch adsorption experiments, powder X-ray diffraction (XRD), and X-ray absorption spectroscopy (XAS). The adsorption isotherm experiments indicated that As(V) uptake increased with increasing [As(V)]0 from 50 to 1000 ??M (i.e., Langmuir type adsorption isotherm) and that the total As adsorption slightly decreased with increasing NaCl concentrations from 0.01 to 0.1 M. Arsenate adsorption was initially (0-10 h) rapid followed by a slow continuum uptake, and the adsorption processes reached the steady state after 720 h. X-ray absorption spectroscopic analyses suggest that As(V) predominantly forms bidentate binuclear surface species on aluminum octahedral structures, and these species are stable up to 11 months. Solubility calculations and powder XRD analyses indicate no evidence of crystalline AI-As(V) precipitates in the experimental systems. Overall, macroscopic and spectroscopic evidence suggest that the As(V) adsorption mechanisms at the allophane-water interface are attributable to ligand exchange reactions between As(V) and surface-coordinated water molecules and hydroxyl and silicate ions. The research findings imply that dissolved tetrahedral oxyanions (e.g., H2PO42- and H2AsO42-) are readily retained on amorphous aluminosilicate minerals in aquifer and soils at near neutral pH. The innersphere adsorption mechanisms might be important in controlling dissolved arsenate and phosphate in amorphous aluminosilicate-rich low-temperature geochemical environments. ?? 2005 American Chemical Society.

  13. Symmetries in fluctuations far from equilibrium.

    PubMed

    Hurtado, Pablo I; Pérez-Espigares, Carlos; del Pozo, Jesús J; Garrido, Pedro L

    2011-05-10

    Fluctuations arise universally in nature as a reflection of the discrete microscopic world at the macroscopic level. Despite their apparent noisy origin, fluctuations encode fundamental aspects of the physics of the system at hand, crucial to understand irreversibility and nonequilibrium behavior. To sustain a given fluctuation, a system traverses a precise optimal path in phase space. Here we show that by demanding invariance of optimal paths under symmetry transformations, new and general fluctuation relations valid arbitrarily far from equilibrium are unveiled. This opens an unexplored route toward a deeper understanding of nonequilibrium physics by bringing symmetry principles to the realm of fluctuations. We illustrate this concept studying symmetries of the current distribution out of equilibrium. In particular we derive an isometric fluctuation relation that links in a strikingly simple manner the probabilities of any pair of isometric current fluctuations. This relation, which results from the time-reversibility of the dynamics, includes as a particular instance the Gallavotti-Cohen fluctuation theorem in this context but adds a completely new perspective on the high level of symmetry imposed by time-reversibility on the statistics of nonequilibrium fluctuations. The new symmetry implies remarkable hierarchies of equations for the current cumulants and the nonlinear response coefficients, going far beyond Onsager's reciprocity relations and Green-Kubo formulas. We confirm the validity of the new symmetry relation in extensive numerical simulations, and suggest that the idea of symmetry in fluctuations as invariance of optimal paths has far-reaching consequences in diverse fields. PMID:21493865

  14. Symmetries in fluctuations far from equilibrium

    PubMed Central

    Hurtado, Pablo I.; Pérez-Espigares, Carlos; del Pozo, Jesús J.; Garrido, Pedro L.

    2011-01-01

    Fluctuations arise universally in nature as a reflection of the discrete microscopic world at the macroscopic level. Despite their apparent noisy origin, fluctuations encode fundamental aspects of the physics of the system at hand, crucial to understand irreversibility and nonequilibrium behavior. To sustain a given fluctuation, a system traverses a precise optimal path in phase space. Here we show that by demanding invariance of optimal paths under symmetry transformations, new and general fluctuation relations valid arbitrarily far from equilibrium are unveiled. This opens an unexplored route toward a deeper understanding of nonequilibrium physics by bringing symmetry principles to the realm of fluctuations. We illustrate this concept studying symmetries of the current distribution out of equilibrium. In particular we derive an isometric fluctuation relation that links in a strikingly simple manner the probabilities of any pair of isometric current fluctuations. This relation, which results from the time-reversibility of the dynamics, includes as a particular instance the Gallavotti–Cohen fluctuation theorem in this context but adds a completely new perspective on the high level of symmetry imposed by time-reversibility on the statistics of nonequilibrium fluctuations. The new symmetry implies remarkable hierarchies of equations for the current cumulants and the nonlinear response coefficients, going far beyond Onsager’s reciprocity relations and Green–Kubo formulas. We confirm the validity of the new symmetry relation in extensive numerical simulations, and suggest that the idea of symmetry in fluctuations as invariance of optimal paths has far-reaching consequences in diverse fields. PMID:21493865

  15. Random sequential adsorption of tetramers

    NASA Astrophysics Data System (ADS)

    Cieśla, Michał

    2013-07-01

    Adsorption of a tetramer built of four identical spheres was studied numerically using the random sequential adsorption (RSA) algorithm. Tetramers were adsorbed on a two-dimensional, flat and homogeneous surface. Two different models of the adsorbate were investigated: a rhomboid and a square one; monomer centres were put on vertices of rhomboids and squares, respectively. Numerical simulations allow us to establish the maximal random coverage ratio as well as the available surface function (ASF), which is crucial for determining kinetics of the adsorption process. These results were compared with data obtained experimentally for KfrA plasmid adsorption. Additionally, the density autocorrelation function was measured.

  16. Removal of aluminium from aqueous solutions using PAN-based adsorbents: characterisation, kinetics, equilibrium and thermodynamic studies.

    PubMed

    Aly, Zaynab; Graulet, Adrien; Scales, Nicholas; Hanley, Tracey

    2014-03-01

    Economic adsorbents in bead form were fabricated and utilised for the adsorption of Al(3+) from aqueous solutions. Polyacrylonitrile (PAN) beads, PAN powder and the thermally treated PAN beads (250 °C/48 h/Ar and 600 °C/48 h/Ar-H2) were characterised using different techniques including Fourier transform infrared spectroscopy, X-ray diffraction, specific surface analysis (Brunauer-Emmett-Teller), thermogravimetric analysis as well as scanning electron microscopy. Effects of pH, contact time, kinetics and adsorption isotherms at different temperatures were investigated in batch mode experiments. Aluminium kinetic data best fit the Lagergren pseudo-second-order adsorption model indicating a one-step, surface-only, adsorption process with chemisorption being the rate limiting step. Equilibrium adsorption data followed a Langmuir adsorption model with fairly low monolayer adsorption capacities suitable for freshwater clean-up only. Various constants including thermodynamic constants were evaluated from the experimental results obtained at 20, 40 and 60 °C. Positive values of ΔH° indicated that the adsorption of Al(3+) onto all three adsorbents was endothermic with less energy input required for PAN powder compared to PAN beads and low-temperature thermally treated PAN. Negative ΔG° values indicated that the aluminium adsorption process was spontaneous for all adsorbents examined. PMID:24297464

  17. Always Connected, but Hard to Reach

    ERIC Educational Resources Information Center

    Rishi, Raju

    2007-01-01

    Students seem to be always connected through their computers, personal digital assistants (PDAs), or mobile phones, making it easy to reach them--if you are a peer. For colleges and universities, reaching students with timely and relevant information often proves a challenge. With rapid changes in both technology and social practices, what should…

  18. Calibrating Reach Distance to Visual Targets

    ERIC Educational Resources Information Center

    Mon-Williams, Mark; Bingham, Geoffrey P.

    2007-01-01

    The authors investigated the calibration of reach distance by gradually distorting the haptic feedback obtained when participants grasped visible target objects. The authors found that the modified relationship between visually specified distance and reach distance could be captured by a straight-line mapping function. Thus, the relation could be…

  19. School Furniture Dimensions: Standing and Reaching.

    ERIC Educational Resources Information Center

    Department of Education and Science, London (England).

    Performance of school children in regard to their standing and reach postures are described with dimensions given on the limits of their performance only. The facts of task performances are presented for the following tasks--(1) seeing into a shelf, (2) reaching into a shelf, (3) drawing on a vertical surface, (4) sitting or standing while…

  20. Interaction of removal Ethidium Bromide with Carbon Nanotube: Equilibrium and Isotherm studies.

    PubMed

    Moradi, Omid; Norouzi, Mehdi; Fakhri, Ali; Naddafi, Kazem

    2014-01-01

    Drinking water resources may be contaminated with Ethidium Bromide (EtBr) which is commonly used in molecular biology laboratories for DNA identification in electrophoresis. Carbon nanotubes are expected to play an important role in sensing, pollution treatment and separation techniques. In this study adsorption of Ethidium Bromide on single-walled carbon nanotubes (SWCNTs) and carboxylate group functionalized single-walled carbon nanotube (SWCNT-COOH) surfaces have been investigated by UV-vis spectrophotometer. The effect of contact time, initial concentration and temperature were investigated. The adsorbents exhibits high efficiency for EtBr adsorption and equilibrium can be achieved in 6 and 3 min for SWCNTs and SWCNT-COOH, respectively. The effect of temperature on adsorption of EtBr by toward adsorbents shows the process in this research has been endothermic. The results showed that the equilibrium data were well described by the Langmuir isotherm model, with a maximum adsorption capacity of 0.770 and 0.830 mg/g for SWCNTs and SWCNT-COOH, respectively. The adsorption of EtBr on SWCNT-COOH is more than SWCNTs surfaces. A comparison of kinetic models was evaluated for the pseudo first-order, pseudo second-order models. Pseudo second-order was found to agree well with the experimental data. PMID:24401790

  1. Interaction of removal Ethidium Bromide with Carbon Nanotube: Equilibrium and Isotherm studies

    PubMed Central

    2014-01-01

    Drinking water resources may be contaminated with Ethidium Bromide (EtBr) which is commonly used in molecular biology laboratories for DNA identification in electrophoresis. Carbon nanotubes are expected to play an important role in sensing, pollution treatment and separation techniques. In this study adsorption of Ethidium Bromide on single-walled carbon nanotubes (SWCNTs) and carboxylate group functionalized single-walled carbon nanotube (SWCNT-COOH) surfaces have been investigated by UV–vis spectrophotometer. The effect of contact time, initial concentration and temperature were investigated. The adsorbents exhibits high efficiency for EtBr adsorption and equilibrium can be achieved in 6 and 3 min for SWCNTs and SWCNT-COOH, respectively. The effect of temperature on adsorption of EtBr by toward adsorbents shows the process in this research has been endothermic. The results showed that the equilibrium data were well described by the Langmuir isotherm model, with a maximum adsorption capacity of 0.770 and 0.830 mg/g for SWCNTs and SWCNT-COOH, respectively. The adsorption of EtBr on SWCNT-COOH is more than SWCNTs surfaces. A comparison of kinetic models was evaluated for the pseudo first-order, pseudo second-order models. Pseudo second-order was found to agree well with the experimental data. PMID:24401790

  2. Experimental comparison of adsorption characteristics of silica gel and zeolite in moist air

    NASA Astrophysics Data System (ADS)

    Xin, F.; Yuan, Z. X.; Wang, W. C.; Du, C. X.

    2016-05-01

    In this work, the macro adsorption characteristic of water vapor by the allochroic silica gel and the zeolite 5A and ZSM-5 were investigated experimentally. BET analysis method presented the difference of the porosity, the micro pore volume, and the specific surface area of the material. The dynamic and the equilibrium characteristics of the sample were measured thermo-gravimetrically in the moist air. In general, the ZSM-5 zeolite showed an inferior feature of the adsorption speed and the equilibrium concentration to the others. By comparison to the result of SAPO-34 zeolite in the open literature, the 5A zeolite showed some superiorities of the adsorption. The equilibrium concentration of the ZSM-5 zeolite was higher than that of the SAPO-34 calcined in the nitrogen, whereas it was lower than that calcined in the air. The adsorption isotherm was correlated and the relation of the isotherm to the microstructure of the material was discussed. With more mesopore volume involved, the zeolite presented an S-shaped isotherm in contrast to the exponential isotherm of the silica gel. In addition, the significance of the S-shaped isotherm for the application in adsorption heat pump has also been addressed.

  3. Rethinking Critical Adsorption

    NASA Astrophysics Data System (ADS)

    Franck, Carl; Peach, Sarah; Polak, Robert D.

    1996-03-01

    Recent reflectivity experiments on near-critical mixtures of carbon disulfide and nitromethane contained in glass cells footnote Niraj S. Desai, Sarah Peach, and Carl Franck, Phys. Rev. E 52, 4129 (1995) have shown that preferential adsorption of one liquid component onto the wall can be controlled by chemical modification of the glass. The glass was treated with varying amounts of hexamethyldisilazane to decrease surface polarity and therefore enhance the adsorption of carbon disulfide in a surprisingly continuous way. The effect of the glass wall on the local liquid composition can be described by two different scaling hypotheses: using a short range field on the liquid closest to the wall, or pinning the amplitude of the order parameter at the surface. We have found that only the second approach is consistent with the experimental data, although this is difficult to reconcile with observed wetting critical phenomena. We also have reexamined the issue of substrate inhomogeneity and conclude that the substrates were indeed homogeneous on relevant length scales. Supported by the NSF under DMR-9320910 and the central facilities of the Materials Science Center at Cornell University.

  4. Understanding the adsorption mechanism of chitosan onto poly(lactide-co-glycolide) particles

    PubMed Central

    Guo, Chunqiang; Gemeinhart, Richard A.

    2008-01-01

    Polyelectrolyte-coated nanoparticles or microparticles interact with bioactive molecules (peptides, proteins or nucleic acids) and have been proposed as delivery systems for these molecules. However, the mechanism of adsorption of polyelectrolyte onto particles remains unsolved. In this study, cationic poly(lactide-co-glycolide) (PLGA) nanoparticles were fabricated by adsorption of various concentrations of a biodegradable polysaccharide, chitosan (0–2.4 g/L), using oil-in-water emulsion and solvent evaporation techniques. The particle diameter, zeta-potential, and chitosan adsorption of chitosan coated PLGA nanoparticles confirmed the increase of polyelectrolyte adsorption. Five adsorption isotherm models (Langmuir, Freundlich, Halsey, Henderson and Smith) were applied to the experimental data in order to better understand the mechanism of adsorption. Both particle diameter and chitosan adsorption increased with chitosan concentration during adsorption. A good correlation was obtained between PLGA-chitosan nanoparticle size and adsorbed chitosan on the surface, suggesting the increased particle size was primarily due to the increased chitosan adsorption. The zeta-potential of chitosan-coated PLGA nanoparticles was positive and increased with chitosan adsorbed until a maximum value (+55 mV) was reached at approximately 0.4–0.6 g/L; PLGA nanoparticles had a negative zeta-potential (−20 mV) prior to chitosan adsorption. Chitosan adsorption on PLGA nanoparticles followed a multilayer adsorption behavior, although the Langmuir monolayer equation held at low concentrations of chitosan. The underlying reasons for adsorption of chitosan on PLGA nanoparticles were thought to be the cationic nature of chitosan, high surface energy and microporous non-uniform surface of PLGA nanoparticles. PMID:18602994

  5. Adsorption and desorption of Zn, Cu, and Cr by sediments from the Raisin River (Michigan)

    SciTech Connect

    Young, T.C.; DePinto, J.V.; Kipp, T.W.

    1987-01-01

    Metal absorption by Raisin River sediments in vitro depended linearly on soluble metal concentration to adsorption densities of 6000-9000 ..mu..g/g with 48 hr partition coefficients of approximately 50, 30, and 25 L/g for Cu, Cr, and Zn, respectively. Partition coefficient computed from field data spanned a comparatively wider range of values in a manner consistent with the often reported adsorbent concentration effect, but other factors likely contributed, too. Desorption of Zn was complete and rapid in contrast to Cr, which was incomplete and much slower; Cu desorption was intermediate to Zn and Cr. A reversible-resistant equilibrium model could not describe the observations as Cu and Cr had not reached metastable desorption equilibria after 24 days. Metal desorption, however, could be described kinetically by distributing sorbed cations between either of two classes; rapidly desorbing and slowly desorbing cations. Sequential and simultaneous desorption models gave similar predictions. Aqueous chemical considerations suggested precipitated as well as adsorbed species could give rise to the observations, but available data did not permit adequate tests of this hypothesis. The extent to which kinetic constraints rather than irreversible reactions account for the desorption-resistant binding signifies a potentially greater metal mobility of bioavailability than would otherwise be assumed. 27 references, 5 figures, 4 tables.

  6. The Database for Reaching Experiments and Models

    PubMed Central

    Walker, Ben; Kording, Konrad

    2013-01-01

    Reaching is one of the central experimental paradigms in the field of motor control, and many computational models of reaching have been published. While most of these models try to explain subject data (such as movement kinematics, reaching performance, forces, etc.) from only a single experiment, distinct experiments often share experimental conditions and record similar kinematics. This suggests that reaching models could be applied to (and falsified by) multiple experiments. However, using multiple datasets is difficult because experimental data formats vary widely. Standardizing data formats promises to enable scientists to test model predictions against many experiments and to compare experimental results across labs. Here we report on the development of a new resource available to scientists: a database of reaching called the Database for Reaching Experiments And Models (DREAM). DREAM collects both experimental datasets and models and facilitates their comparison by standardizing formats. The DREAM project promises to be useful for experimentalists who want to understand how their data relates to models, for modelers who want to test their theories, and for educators who want to help students better understand reaching experiments, models, and data analysis. PMID:24244351

  7. Adsorption behavior of EE2 (17 alpha-ethinylestradiol) onto the inactivated sewage sludge: kinetics, thermodynamics and influence factors.

    PubMed

    Feng, Yujie; Zhang, Zhaohan; Gao, Peng; Su, Hui; Yu, Yanling; Ren, Nanqi

    2010-03-15

    The adsorption behavior of 17 alpha-ethinylestradiol (EE(2)) onto inactivated sludge was investigated to assess the function of adsorption on EE(2) removal in activated sludge system. The adsorption equilibrium of EE(2) can be achieved in 5.0 h at the research temperature and the adsorption process could be well described by pseudo-second-order model. The equilibrium data at different temperatures were fitted by a linear regression. The thermodynamics analysis revealed that EE(2) adsorption onto inactivated sludge was spontaneous (Delta G=-15.18 to -16.35 kJ/mol), enthalpy-driven (Delta H=-27.2 kJ/mol), entropy-retarded (DeltaS=-39.18 J/(mol K)), and mainly physical adsorption. Effects of pH, ionic strength and coexisting organic matters (methanol and bisphenol A) on EE(2) adsorption onto inactivated sludge were also examined. The amounts of EE(2) equilibrium adsorption ability were unchanged as the pH values increasing from 2.0 to 6.0, but decreased from 2.14 to 1.43 mg/g MLSS when the initial EE(2) concentration was 5.0mg/L as pH above 6.0. The adsorption capacities were first increased from 2.19 to 2.50mg/g MLSS, then sharply decreased and stabilized at 1.12 mg/g MLSS during the ionic strength was adjusted from 0 to 1 mol/L. Methanol (0.4-5%, v/v) and bisphenol A (0-200mg/L) in the mixed liquor can decrease the adsorption capacity of EE(2) from 2.19 to 1.39 and 0.75 mg/g MLSS, respectively. PMID:19945220

  8. On the thermodynamics of refrigerant + heterogeneous solid surfaces adsorption.

    PubMed

    Ismail, Azhar Bin; Li, Ang; Thu, Kyaw; Ng, K C; Chun, Wongee

    2013-11-26

    This Article presents a theoretical framework for the understanding of pressurized adsorption systems using the statistical rate methodology. Utilizing results from the statistical rate theory, basic thermodynamic variables including enthalpy (h(a)), entropy (s(a)), and the specific heat capacity (c(p,a)) of the adsorbed phase are derived using the thermodynamic requirements of chemical equilibrium, Gibbs law, as well as Maxwell relations. A built-in constant (K) describes the adsorbed molecular partition function (q(s)), and it captures the heterogeneous properties of the adsorbent + adsorbate pair at equilibrium states. Improved adsorbed-phase volume considerations were incorporated in the formulations of these variables where they could be utilized with relative ease for analyzing the energetic performances of any practical adsorption system. In this Article, we have demonstrated how derived thermodynamic quantities can bridge the information gap with respect to the states of adsorbed phase, as well as resolved some theoretical inconsistencies that were found in previously derived quantities. Experimentally, the adsorption isotherms of propane (refrigerant) on activated carbon powder (Maxsorb III) for temperatures from 5 to 75 °C and pressures up to 8 bar are presented, and they are used to illustrate the behaviors of the adsorbed-phase during uptakes, temperatures, and pressure excursions or changes. PMID:24191669

  9. Polyphenylene sulfide based anion exchange fiber: synthesis, characterization and adsorption of Cr(VI).

    PubMed

    Huang, Jiajia; Zhang, Xin; Bai, Lingling; Yuan, Siguo

    2012-01-01

    A fibrous strong base anion exchanger (QAPPS) was prepared for the first time via chloromethylation and quaternary amination reaction of polyphenylene sulfide fiber (PPS), and its physical-chemical structure and adsorption behavior for Cr(VI) were characterized by FTIR, Energy Dispersive Spectrometry, TG-DTG, elemental analysis and batch adsorptive technique, respectively. The novel fibrous adsorbent could effectively adsorb Cr(VI) over the pH range 1-12, the maximum adsorption capacity was 166.39 mg/g at pH 3.5, and the adsorption behavior could be described well by Langmuir isotherm equation model. The adsorption kinetics was studied using pseudo first-order and pseudo second-order models, and the t1/2 and equilibrium adsorption time were 5 and 20 min respectively when initial Cr(VI) concentration was 100 mg/L. The saturated fibers could be regenerated rapidly by a mixed solution of 0.5 mol/L NaOH and 0.5 mol/L NaCl, and the adsorption capacity was well maintained after six adsorption-desorption cycles. PMID:23513685

  10. [Effects of biochars produced from different sources on arsenic adsorption and desorption in soil].

    PubMed

    Guan, Lian-Zhu; Zhou, Jing-Jing; Zhang, Yun; Zhang, Guang-Cai; Zhang, Jin-Hai; Chan, Zhong-Xiang

    2013-10-01

    By using OECD Guideline 106 batch equilibrium method, this paper studied the characteristics of As (V) adsorption and desorption in brown soil as affected by the biochars produced from dairy manure, pine needle, and corn straw. When the addition amount of the biochars was 0.5%, the maximum adsorption amount of As (V) was decreased in the order of dairy manure biochar > pine needle biochar > corn straw biochar, which was related to the basic characteristics of the biochars. The adsorption isotherm of As (V) could be well fitted by Langmuir model (R2 = 0.997). In comparing with CK, both the adsorption capacity (lgKf = 1.99-2.10) and the adsorption intensity (1/N = 0.413-0.449) of As (V) were low, and the main adsorption mechanism was physical adsorption. The desorption rate of As (V) (14.5%-18.7%) was decreased in the order of dairy manure biochar > pine needle biochar > corn straw biochar. The addition of the biochars decreased the adsorption of As (V) by brown soil, which could induce the increase of the bioavailability of As, and strengthen the toxicity of As in soil. PMID:24483091

  11. Entropically favored adsorption of cellulosic molecules onto carbon materials through hydrophobic functionalities.

    PubMed

    Yabushita, Mizuho; Kobayashi, Hirokazu; Hasegawa, Jun-Ya; Hara, Kenji; Fukuoka, Atsushi

    2014-05-01

    Carbon-based materials have attracted interest as high-performance catalysts for the aqueous-phase conversion of cellulose. The adsorption of β-glucans plays a crucial role in the catalytic performance of carbons, although the primary driving force and details of the adsorption process remain unclear. This study demonstrates that adsorption occurs at hydrophobic sites on the carbon surface and that hydrophilic groups are not involved. Analysis of adsorption temperature dependence also reveals that the entropy change associated with adsorption is positive. Our results indicate that adsorption occurs by entropically driven hydrophobic interactions in addition to CH-π hydrogen bonding. These same CH-π hydrogen bonds are also confirmed by DFT calculations. The adsorption of β-glucans on carbons is significantly stronger than the affinity between β-glucans. The adsorption equilibrium constants of β-glucans on carbons increase exponentially with increasing degrees of polymerization, which supports the theory of strong interactions between the carbon and the long β-glucans found in cellulose. PMID:24644071

  12. Oleate adsorption at an apatite surface studied by ex-situ FTIR internal reflection spectroscopy

    SciTech Connect

    Lu, Y.; Drelich, J.; Miller, J.D.

    1998-06-15

    Oleate adsorption at an apatite surface was investigated by ex-situ Fourier transform infrared internal reflection spectroscopy (FTIR/IRS). Adsorption isotherms have been determined using an apatite internal reflection element (IRE) and it has been found that pH has a significant influence on oleate adsorption by apatite. At pH 8.0 and 20 C, oleate adsorption density increases monotonically as equilibrium oleate concentration increases from 5 {times} 10{sup {minus}6} to 1 {times} 10{sup {minus}3} M. These results are in contrast to the results at pH 9.5 and 20 C in which case the adsorption density is limited to that corresponding to approximately monolayer coverage. Oleate adsorption by apatite was compared to oleate adsorption by fluorite and calcite and the different adsorption behavior at these three mineral surfaces is attributed to the differences in the densities of surface calcium sites and to the differences in the solubilities of these minerals. Contact angles have been measured at the apatite IRE surface and it has been demonstrated that both the amount and the nature of the adsorbed species influence the hydrophobic state of the surface.

  13. Bovine serum albumin adsorption onto functionalized polystyrene lattices: A theoretical modeling approach and error analysis

    NASA Astrophysics Data System (ADS)

    Beragoui, Manel; Aguir, Chadlia; Khalfaoui, Mohamed; Enciso, Eduardo; Torralvo, Maria José; Duclaux, Laurent; Reinert, Laurence; Vayer, Marylène; Ben Lamine, Abdelmottaleb

    2015-03-01

    The present work involves the study of bovine serum albumin adsorption onto five functionalized polystyrene lattices. The adsorption measurements have been carried out using a quartz crystal microbalance. Poly(styrene-co-itaconic acid) was found to be an effective adsorbent for bovine serum albumin molecule adsorption. The experimental isotherm data were analyzed using theoretical models based on a statistical physics approach, namely monolayer, double layer with two successive energy levels, finite multilayer, and modified Brunauer-Emmet-Teller. The equilibrium data were then analyzed using five different non-linear error analysis methods and it was found that the finite multilayer model best describes the protein adsorption data. Surface characteristics, i.e., surface charge density and number density of surface carboxyl groups, were used to investigate their effect on the adsorption capacity. The combination of the results obtained from the number of adsorbed layers, the number of adsorbed molecules per site, and the thickness of the adsorbed bovine serum albumin layer allows us to predict that the adsorption of this protein molecule can also be distinguished by monolayer or multilayer adsorption with end-on, side-on, and overlap conformations. The magnitudes of the calculated adsorption energy indicate that bovine serum albumin molecules are physisorbed onto the adsorbent lattices.

  14. Ultrasound-assisted adsorption of 4-dodecylbenzene sulfonate from aqueous solutions by corn cob activated carbon.

    PubMed

    Milenković, D D; Bojić, A Lj; Veljković, V B

    2013-05-01

    This study was aimed at removal of 4-dodecylbenzene sulfonate (DBS) ions from aqueous solutions by ultrasound-assisted adsorption onto the carbonized corn cob (AC). The main attention was focused on modeling the equilibrium and kinetics of adsorption of DBS onto the AC. The AC was prepared from ground dried corn cob by carbonization and activation by carbon dioxide at 880°C for 2h in a rotary furnace. The adsorption isotherm data were fitted by the Langmuir model in both the absence and the presence of ultrasound (US). The maximum adsorption capacities of the adsorbent for DBS, calculated from the Langmuir isotherms, were 29.41mg/g and 27.78mg/g in the presence of US and its absence, respectively. The adsorption process in the absence and the presence of US obeyed the pseudo second-order kinetics. The intraparticular diffusion model indicated that the adsorption of DBS ions on the AC was diffusion controlled as well as that US promoted intraparticular diffusion. The ΔG° values, -24.03kJ/mol, -25.78kJ/mol and -27.78kJ/mol, were negative at all operating temperatures, verifying that the adsorption of DBS ions was spontaneous and thermodynamically favorable. The positive value of ΔS°=187J/molK indicated the increased randomness at the adsorbent-adsorbate interface during the adsorption of DBS ions by the AC. PMID:23187067

  15. Adsorption of Benzoic Acid in Aqueous Solution by Bagasse Fly Ash

    NASA Astrophysics Data System (ADS)

    Suresh, S.

    2012-09-01

    This paper reports the studies on the benzoic acid (BA) onto bagasse fly ash (BFA) was studied in aqueous solution in a batch system. Physico-chemical properties including surface area, surface texture of the GAC before and after BA adsorption onto BFA were analysed using X-ray diffractometer (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The optimum initial pH for the adsorption of BA was found to be 5.56. The adsorbent dose was 10 g/l for BFA and the equilibrium time 8 h of reaction. Pseudo first and second order models were used to find the adsorption kinetics. It was found that intraparticle diffusion played important role in the adsorption mechanisms of BA and the adsorption kinetics followed pseudo-second order kinetic model rather than the pseudo first order kinetic model. Isotherm data were generated for BA solution having initial concentrations of BA in the range of 10-200 mg/l for the BFA dosage of 10 g/l at temperatures of 288, 303, and 318 K. The adsorption of BA onto BFA was favorably influenced by an increase in temperature. Equilibrium data were well represented by the Redlich-Peterson isotherm model. Values of the change in entropy ( ΔS 0), heat of adsorption ( ΔH 0) for adsorption of BA on BFA was found to be 120.10 and 19.61 kJ/mol respectively. The adsorption of BA onto BFA was an endothermic reaction. Desorption of BA from BFA was studied by various solvents method. Acetic acid was found to be a better eluant for desorption of BA with a maximum desorption efficiency of 55.2 %. Owing to its heating value, spent BFA can be used as a co-fuel for the production of heat in boiler furnaces.

  16. Competitive adsorption-desorption reactions of two hazardous heavy metals in contaminated soils.

    PubMed

    Davari, Masoud; Rahnemaie, Rasoul; Homaee, Mehdi

    2015-09-01

    Investigating the interactions of heavy metals is imperative for sustaining environment and human health. Among those, Cd is toxic for organisms at any concentration. While Ni acts as a micronutrient at very low concentration but is hazardous toxic above certain threshold value. In this study, the chemical adsorption and desorption reactions of Ni and Cd in contaminated soils were investigated in both single and binary ion systems. Both Ni and Cd experimental data demonstrated Langmuir type adsorption. In the competitive systems, an antagonistic effect was observed, implying that both ions compete for same type of adsorption sites. Adverse effect of Cd on Ni adsorption was slightly stronger than that of opposite system, consistent with adsorption isotherms in single ion systems. Variation in ionic strength indicated that Ca, a much weaker adsorbate, could also compete with Cd and Ni for adsorption on soil particles. Desorption data indicated that Cd and Ni are adsorbed very tightly such that after four successive desorption steps, less than 0.5 % of initially adsorbed ions released into the soil solution. This implies that Ca, at concentration in equilibrium with calcite mineral, cannot adequately compete with and replace adsorbed Ni and Cd ions. This adsorption behavior was led to considerable hysteresis between adsorption and desorption in both single and binary ion systems. In the binary ion systems, desorption of Cd and Ni was increased by increase in both equilibrium concentration of adsorbed ion and concentration of competitor ion. The overall results obtained in this research indicate that Cd and Ni are strongly adsorbed in calcareous soil and Ca, the major dissolved ion, insignificantly influences metal ions adsorption. Consequently, the contaminated soils by Ni and Cd can simultaneously be remediated by environmentally oriented technologies such as phytoremediation. PMID:25921756

  17. General equilibrium of an ecosystem.

    PubMed

    Tschirhart, J

    2000-03-01

    Ecosystems and economies are inextricably linked: ecosystem models and economic models are not linked. Consequently, using either type of model to design policies for preserving ecosystems or improving economic performance omits important information. Improved policies would follow from a model that links the systems and accounts for the mutual feedbacks by recognizing how key ecosystem variables influence key economic variables, and vice versa. Because general equilibrium economic models already are widely used for policy making, the approach used here is to develop a general equilibrium ecosystem model which captures salient biological functions and which can be integrated with extant economic models. In the ecosystem model, each organism is assumed to be a net energy maximizer that must exert energy to capture biomass from other organisms. The exerted energies are the "prices" that are paid to biomass, and each organism takes the prices as signals over which it has no control. The maximization problem yields the organism's demand for and supply of biomass to other organisms as functions of the prices. The demands and supplies for each biomass are aggregated over all organisms in each species which establishes biomass markets wherein biomass prices are determined. A short-run equilibrium is established when all organisms are maximizing and demand equals supply in every biomass market. If a species exhibits positive (negative) net energy in equilibrium, its population increases (decreases) and a new equilibrium follows. The demand and supply forces in the biomass markets drive each species toward zero stored energy and a long-run equilibrium. Population adjustments are not based on typical Lotka-Volterra differential equations in which one entire population adjusts to another entire population thereby masking organism behavior; instead, individual organism behavior is central to population adjustments. Numerical simulations use a marine food web in Alaska to

  18. Removal Rate of Organic Matter Using Natural Cellulose via Adsorption Isotherm and Kinetic Studies.

    PubMed

    Din, Mohd Fadhil Md; Ponraj, Mohanadoss; Low, Wen-Pei; Fulazzaky, Mohamad Ali; Iwao, Kenzo; Songip, Ahmad Rahman; Chelliapan, Shreeshivadasan; Ismail, Zulhilmi; Jamal, Mohamad Hidayat

    2016-02-01

    In this study, the removal of natural organic matter (NOM) using coconut fiber (CF) and palm oil fiber (POF) was investigated. Preliminary analysis was performed using a jar test for the selection of optimal medium before the fabricated column model experiment. The equilibrium studies on isotherms and kinetic models for NOM adsorption were analyzed using linearized correlation coefficient. Results showed that the equilibrium data were fitted to Langmuir isotherm model for both CF and POF. The most suitable adsorption model was the pseudo-first-order kinetic model for POF and pseudo-second-order kinetic model for CF. The adsorption capacities achieved by the CF and POF were 15.67 and 30.8 mg/g respectively. Based on this investigation, it can be concluded that the POF is the most suitable material for the removal of NOM in semi polluted river water. PMID:26803100

  19. Competitive adsorption of furfural and phenolic compounds onto activated carbon in fixed bed column.

    PubMed

    Sulaymon, Abbas H; Ahmed, Kawther W

    2008-01-15

    For a multicomponent competitive adsorption of furfural and phenolic compounds, a mathematical model was builtto describe the mass transfer kinetics in a fixed bed column with activated carbon. The effects of competitive adsorption equilibrium constant, axial dispersion, external mass transfer, and intraparticle diffusion resistance on the breakthrough curve were studied for weakly adsorbed compound (furfural) and strongly adsorbed compounds (parachlorophenol and phenol). Experiments were carried out to remove the furfural and phenolic compound from aqueous solution. The equilibrium data and intraparticle diffusion coefficients obtained from separate experiments in a batch adsorber, by fitting the experimental data with theoretical model. The results show that the mathematical model includes external mass transfer and pore diffusion using nonlinear isotherms and provides a good description of the adsorption process for furfural and phenolic compounds in a fixed bed adsorber. PMID:18284136

  20. Uphill diffusion and overshooting in the adsorption of binary mixtures in nanoporous solids.

    PubMed

    Lauerer, Alexander; Binder, Tomas; Chmelik, Christian; Miersemann, Erich; Haase, Jürgen; Ruthven, Douglas M; Kärger, Jörg

    2015-01-01

    Under certain conditions, during binary mixture adsorption in nanoporous hosts, the concentration of one component may temporarily exceed its equilibrium value. This implies that, in contrast to Fick's Law, molecules must diffuse in the direction of increasing rather than decreasing concentration. Although this phenomenon of 'overshooting' has been observed previously, it is only recently, using microimaging techniques, that diffusive fluxes in the interior of nanoporous materials have become accessible to direct observation. Here we report the application of interference microscopy to monitor 'uphill' fluxes, covering the entire period of overshooting from initiation until final equilibration. It is shown that the evolution of the profiles can be adequately predicted from the single-component diffusivities together with the binary adsorption equilibrium data. The guest molecules studied (carbon dioxide, ethane and propene) and the host material (ZSM-58 or DDR) are of practical interest in relation to the development of kinetically selective adsorption separation processes. PMID:26177626

  1. Uphill diffusion and overshooting in the adsorption of binary mixtures in nanoporous solids

    NASA Astrophysics Data System (ADS)

    Lauerer, Alexander; Binder, Tomas; Chmelik, Christian; Miersemann, Erich; Haase, Jürgen; Ruthven, Douglas M.; Kärger, Jörg

    2015-07-01

    Under certain conditions, during binary mixture adsorption in nanoporous hosts, the concentration of one component may temporarily exceed its equilibrium value. This implies that, in contrast to Fick's Law, molecules must diffuse in the direction of increasing rather than decreasing concentration. Although this phenomenon of `overshooting' has been observed previously, it is only recently, using microimaging techniques, that diffusive fluxes in the interior of nanoporous materials have become accessible to direct observation. Here we report the application of interference microscopy to monitor `uphill' fluxes, covering the entire period of overshooting from initiation until final equilibration. It is shown that the evolution of the profiles can be adequately predicted from the single-component diffusivities together with the binary adsorption equilibrium data. The guest molecules studied (carbon dioxide, ethane and propene) and the host material (ZSM-58 or DDR) are of practical interest in relation to the development of kinetically selective adsorption separation processes.

  2. Uphill diffusion and overshooting in the adsorption of binary mixtures in nanoporous solids

    PubMed Central

    Lauerer, Alexander; Binder, Tomas; Chmelik, Christian; Miersemann, Erich; Haase, Jürgen; Ruthven, Douglas M.; Kärger, Jörg

    2015-01-01

    Under certain conditions, during binary mixture adsorption in nanoporous hosts, the concentration of one component may temporarily exceed its equilibrium value. This implies that, in contrast to Fick's Law, molecules must diffuse in the direction of increasing rather than decreasing concentration. Although this phenomenon of ‘overshooting' has been observed previously, it is only recently, using microimaging techniques, that diffusive fluxes in the interior of nanoporous materials have become accessible to direct observation. Here we report the application of interference microscopy to monitor ‘uphill' fluxes, covering the entire period of overshooting from initiation until final equilibration. It is shown that the evolution of the profiles can be adequately predicted from the single-component diffusivities together with the binary adsorption equilibrium data. The guest molecules studied (carbon dioxide, ethane and propene) and the host material (ZSM-58 or DDR) are of practical interest in relation to the development of kinetically selective adsorption separation processes. PMID:26177626

  3. A novel polar-modified post-cross-linked resin: Effect of the porogens on the structure and adsorption performance.

    PubMed

    Wang, Xiaomei; Fu, Zhenyu; Yu, Na; Huang, Jianhan

    2016-03-15

    The porogens used in the polymerization play important roles in the structure and adsorption performance for the polar-modified post-cross-linked resins. A series of novel polar-modified post-cross-linked resins were prepared using different mass percentage of toluene and 3-methyl-1-butanol as the mixed porogens. The results indicated that the resins using a higher mass percentage of toluene in the mixed porogens possessed a higher content of pendent vinyl groups, the greater Brunauer-Emmett-Teller (BET) surface area and t-plot micropore surface area. What's more, the Friedel-Crafts alkylation reaction induced a higher increment of the BET surface area and t-plot micropore surface area before and after the post-cross-linking. The resin p(GMA-co-DVB)-22-pc using 50% (w/w) of toluene and 50% (w/w) of 3-methyl-1-butanol in the mixed porogens held the largest equilibrium capacity to phenol among the four considered resins. The equilibrium data was well characterized by the Freundlich model and the isosteric enthalpy decreased dramatically with increasing of the fractional loading. The resin using a lower mass percentage of toluene in the mixed porogens required less time to reach equilibrium because of its less micropores and the minor diffusion resistance in the pores. p(GMA-co-DVB)-22-pc exhibited a dynamic saturated capacity of 55.4 mg/mL wet resin at an initial concentration of 1250 mg/L and a flow rate of 1.4 mL/min, and it could be completely regenerated by 0.001 mol/L of sodium hydroxide (w/v) and 80% of ethanol (v/v). PMID:26748064

  4. Adiabatic evolution of plasma equilibrium

    PubMed Central

    Grad, H.; Hu, P. N.; Stevens, D. C.

    1975-01-01

    A new theory of plasma equilibrium is introduced in which adiabatic constraints are specified. This leads to a mathematically nonstandard structure, as compared to the usual equilibrium theory, in which prescription of pressure and current profiles leads to an elliptic partial differential equation. Topologically complex configurations require further generalization of the concept of adiabaticity to allow irreversible mixing of plasma and magnetic flux among islands. Matching conditions across a boundary layer at the separatrix are obtained from appropriate conservation laws. Applications are made to configurations with planned islands (as in Doublet) and accidental islands (as in Tokamaks). Two-dimensional, axially symmetric, helically symmetric, and closed line equilibria are included. PMID:16578729

  5. Phase coexistence far from equilibrium

    NASA Astrophysics Data System (ADS)

    Dickman, Ronald

    2016-04-01

    Investigation of simple far-from-equilibrium systems exhibiting phase separation leads to the conclusion that phase coexistence is not well defined in this context. This is because the properties of the coexisting nonequilibrium systems depend on how they are placed in contact, as verified in the driven lattice gas with attractive interactions, and in the two-temperature lattice gas, under (a) weak global exchange between uniform systems, and (b) phase-separated (nonuniform) systems. Thus, far from equilibrium, the notions of universality of phase coexistence (i.e., independence of how systems exchange particles and/or energy), and of phases with intrinsic properties (independent of their environment) are lost.

  6. A comprehensive investigation on adsorption of Ca (II), Cr (III) and Mg (II) ions by 3D porous nickel films.

    PubMed

    Lai, Chuan; Guo, Xiaogang; Xiong, Zhongshu; Liu, Changlu; Zhu, Hui; Wu, Mei; Zhang, Daixiong

    2016-02-01

    The present study reports the removal of Ca (II), Cr (III), Mg (II) ions from aqueous solution using 3D-porous nickel films (3DNFs) as a novel adsorbent material prepared by hydrogen bubble dynamic template (HBDT) method at room temperature. The structure morphology and the phase constitution of 3DNFs were characterized by FESEM, EDS and XRD. Adsorption process of Ca (II), Cr (III), Mg (II) ions was fast as the equilibrium was established within 30min, and the maximum adsorption at equilibrium was 44.1mg/g, 46.4mg/g and 32.7mg/g, respectively. The adsorption kinetics well fitted using a pseudo second-order kinetic model. The adsorption isotherm data of all the three metals fit well the Langmuir and Freundlich adsorption isotherm model. It was found out that kinetics of adsorption varies with initial concentration of metal ions. Thermodynamic parameters (i.e., the standard Gibbs free energies (ΔG), enthalpy change (ΔH), standard entropy change (ΔS)) were also evaluated. Thermodynamic analysis indicated that a high temperature is favored for the adsorption of metal ions by 3DNFs. These results suggest that 3DNFs have good potential application in effective adsorption of metal ions with satisfactory results. PMID:26520822

  7. Modeling studies: Adsorption of aniline blue by using Prosopis Juliflora carbon/Ca/alginate polymer composite beads.

    PubMed

    Kumar, M; Tamilarasan, R

    2013-02-15

    The research article describes the experimental and modeling study for the adsorptive removal of aniline blue dye (AB dye) from aqueous matrices using a Prosopis Juliflora modified carbon/Ca/alginate polymer bead as a low cost and eco-friendly adsorbent. The rate of adsorption was investigated under various experimental parameters such as contact time, adsorbent dose, dye concentration, pH and temperature. The kinetics, equilibrium and thermodynamic studies were assessed to find out the efficiency of the adsorption process. The equilibrium uptake capacity of the adsorption process was found with Freundlich and Langmuir adsorption isotherm equations and it was evaluated by dimensionless separation factor (R(L)). The dynamics of adsorption was predicted by pseudo-first order, pseudo-second order Lagergren's equation and intra particle diffusion model. Adsorption feasibility was assessed with thermodynamic parameters such as isosteric heat of adsorption (ΔH°), standard entropy (ΔS°) and Gibbs free energy (ΔG°) using VantHoff plot. The alginate bead was characterized with FTIR spectroscopy and Scanning Electron Microscopy (SEM). PMID:23399273

  8. Global versus local adsorption selectivity

    NASA Astrophysics Data System (ADS)

    Pauzat, Françoise; Marloie, Gael; Markovits, Alexis; Ellinger, Yves

    2015-10-01

    The origin of the enantiomeric excess found in the amino acids present in the organic matter of carbonaceous meteorites is still unclear. Selective adsorption of one of the two enantiomers existing after a racemic formation could be part of the answer. Hereafter we report a comparative study of the adsorption of the R and S enantiomers of α-alanine and lactic acid on the hydroxylated { } chiral surface of α-quartz using numerical simulation techniques. Structurally different adsorption sites were found with opposite R versus S selectivity for the same molecule-surface couple, raising the problem of whether to consider adsorption as a local property or as a global response characteristic of the whole surface. To deal with the second term of this alternative, a statistical approach was designed, based on the occurrence of each adsorption site whose energy was calculated using first principle periodic density functional theory. It was found that R-alanine and S-lactic acid are the enantiomers preferentially adsorbed, even if the adsorption process on the quartz { } surface stays with a disappointingly poor enantio-selectivity. Nevertheless, it highlighted the important point that considering adsorption as a global property changes perspectives in the search for more efficient enantio-selective supports and more generally changes the way to apprehend adsorption processes in astro-chemistry/biology.

  9. Liquid-Phase Adsorption Fundamentals.

    ERIC Educational Resources Information Center

    Cooney, David O.

    1987-01-01

    Describes an experiment developed and used in the unit operations laboratory course at the University of Wyoming. Involves the liquid-phase adsorption of an organic compound from aqueous solution on activated carbon, and is relevant to adsorption processes in general. (TW)

  10. ADSORPTION MEDIA FOR ARSENIC REMOVAL

    EPA Science Inventory

    Presentation will discuss the use of adsorptive media for the removal of arsenic from drinking water. Presentation is a fundamental discussion on the use of adsorptive media for arsenic removal and includes information from several EPA field studies on removal of arsenic from dr...

  11. Adsorption of a non-enveloped mammalian virus to functionalized nanofibers.

    PubMed

    Mi, Xue; Heldt, Caryn L

    2014-09-01

    In the pursuit of finding superior methods to remove pathogens from drinking water, this study examines the adsorption of a non-enveloped, mammalian virus to highly charged nanofibers. N-[(2-Hydroxyl-3-trimethylammonium) propyl] chitosan (HTCC) nanofibers were synthesized by the addition of a quaternary amine to chitosan. HTCC was blended with polyvinyl alcohol (PVA) to produce nanofibers by electrospinning. The nanofibers were stabilized against water by crosslinking with glutaraldehyde. When studied in the range of 100-200nm in diameter, larger fibers were able to adsorb about 90% more virus than smaller fibers. The kinetics of the adsorption was modeled with pseudo-first order kinetics and equilibrium was achieved in as little as 10min. Equilibrium adsorption was modeled with the Freundlich isotherm with a Freundlich constant of 1.4. When the Freundlich constant deviates from 1, this demonstrates that there is heterogeneity at the adsorption surface. The heterogeneity likely occurs at the nanofiber surface since a polymeric blend of two polymers was used to electrospin the nanofibers. The model mammalian virus, porcine parvovirus (PPV), has a fairly homogeneous, icosahedral protein capsid available for adsorption. The fast adsorption kinetics and high capacity of the nanofibers make HTCC/PVA a potential filter material for the removal of pathogens from drinking water. PMID:24985761

  12. Molecular Dynamics Simulations of Uranyl and Uranyl Carbonate Adsorption at Alumino-silicate Surfaces

    SciTech Connect

    Kerisit, Sebastien N.; Liu, Chongxuan

    2014-03-03

    Adsorption at mineral surfaces is a critical factor controlling the mobility of uranium(VI) in aqueous environments. Therefore, molecular dynamics (MD) simulations were performed to investigate uranyl(VI) adsorption onto two neutral alumino-silicate surfaces, namely the orthoclase (001) surface and the octahedral aluminum sheet of the kaolinite (001) surface. Although uranyl preferentially adsorbed as a bi-dentate innersphere complex on both surfaces, the free energy of adsorption at the orthoclase surface (-15 kcal mol-1) was significantly more favorable than that at the kaolinite surface (-3 kcal mol-1), which was attributed to differences in surface functional groups and to the ability of the orthoclase surface to dissolve a surface potassium ion upon uranyl adsorption. The structures of the adsorbed complexes compared favorably with X-ray absorption spectroscopy results. Simulations of the adsorption of uranyl complexes with up to three carbonate ligands revealed that uranyl complexes coordinated to up to 2 carbonate ions are stable on the orthoclase surface whereas uranyl carbonate surface complexes are unfavored at the kaolinite surface. Combining the MD-derived equilibrium adsorption constants for orthoclase with aqueous equilibrium constants for uranyl carbonate species indicates the presence of adsorbed uranium complexes with one or two carbonates in alkaline conditions, in support of current uranium(VI) surface complexation models.

  13. Removal of beta-blockers from aqueous media by adsorption onto graphene oxide.

    PubMed

    Kyzas, George Z; Koltsakidou, Anastasia; Nanaki, Stavroula G; Bikiaris, Dimitrios N; Lambropoulou, Dimitra A

    2015-12-15

    The aim of the present study is the evaluation of graphene oxide (GhO) as adsorbent material for the removal of beta-blockers (pharmaceutical compounds) in aqueous solutions. The composition and morphology of prepared materials were characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR). Atenolol (ATL) and propranolol (PRO) were used as model drug molecules and their behavior were investigated in terms of GhO dosage, contact time, temperature and pH. Adsorption mechanisms were proposed and the pH-effect curves after adsorption were discussed. The kinetic behavior of GhO-drugs system was analyzed after fitting to pseudo-first and -second order equations. The adsorption equilibrium data were fitted to Langmuir, Freundlich and Langmuir-Freundlich model calculating the maximum adsorption capacity (67 and 116 mg/g for PRO and ATL (25 °C), respectively). The temperature effect on adsorption was tested carrying out the equilibrium adsorption experiments at three different temperatures (25, 45, 65 °C). Then, the thermodynamic parameters of enthalpy, free energy and entropy were calculated. Finally, the desorption of drugs from GhO was evaluated by using both aqueous eluants (pH2-10) and organic solvents. PMID:26282775

  14. Adsorption of cobalt ions from waste water on activated Saudi clays

    NASA Astrophysics Data System (ADS)

    Al-Jlil, Saad A.

    2014-11-01

    The aim of this work was to remove the Cobalt ions from wastewater by three types of Saudi clay. These were collected from Tabbuk city (Tabbuk clay), Khiber city (Khiber clay), and Bahhah city (Bahhah clay). The paper also examined the effect of different activators on the enhancement of adsorption capacity of clays for cobalt ions. The results showed minor enhancement in the adsorption capacities of cobalt ions on three types of clays activated by acid treatment. The adsorption capacity of clays improved particularly for Tabbuk clay when treated with hydrogen peroxide as an activator. The adsorption capacity increased from 3.94 to 12.9 mg/g for the untreated and treated Tabbuk clay, respectively. Also, the adsorption capacity of Bahhah clay increased by activating with sodium chloride from 3.44 to 12.55 mg/g for untreated and treated sample, respectively. The equilibrium adsorption data were correlated using five equilibrium equations, namely, Langmuir, Freundlich, Langmuir-Freundlich, BET, and Toth isotherm equations. Langmuir isotherm agreed well with the experimental data of Khiber and Bahhah clay, while Freundlich model and Langmuir-Freundlich model fitted well with the experimental data of Tabbuk and Bahhah clay activated by NaCl. The results showed that Freundlich model fitted well with the experimental data of Tabbuk clay when activated by H2O2 and H2SO4. Finally, the BET model did not describe the experimental data well for the three types of clay after activation.

  15. Excellent adsorption and desorption characteristics of polypyrrole/TiO2 composite for Methylene Blue

    NASA Astrophysics Data System (ADS)

    Li, Jingjing; Feng, Jiangtao; Yan, Wei

    2013-08-01

    P25 or self-prepared TiO2 coated polypyrrole (PPy/P25 or PPy/TiO2) composites as novel adsorbents were prepared. Their adsorption-desorption characteristics for Methylene Blue (MB) were comparatively investigated. X-ray photoelectron spectroscopy (XPS) showed that PPy/TiO2 possessed higher doping level than PPy/P25. Thermogravimetric analysis (TGA) indicated that PPy/TiO2 contained more PPy than PPy/P25. The results of water vapor adsorption suggested that the PPy/TiO2 composite was more hydrophobic than PPy/P25. The adsorption results revealed that the composites pretreated in the solution with higher pH value exhibited larger adsorption capacities. The ionic concentration in MB solution slightly impacted the removal of MB by the PPy/TiO2 composite. The adsorption equilibrium results showed that the adsorption of MB was completed in a short time of 30 min. Pseudo-second-order and Langmuir isotherm models were effectively employed to describe the adsorption behavior of MB. PPy/TiO2 and PPy/P25 were found to have better removal ability for MB compared with pure PPy; especially PPy/TiO2, on which the maximum adsorption amount was about 3.6 or 5.5 times higher than that of PPy/P25 or pure PPy, respectively. The thermodynamic analysis indicated that the adsorption of MB was spontaneous and endothermic in nature. The regeneration experiments exhibited that PPy/TiO2 can be reused at least seven times without obvious loss of its original adsorption capacity. Electrostatic interaction, hydrogen bonding and hydrophobic interaction played the roles in MB adsorption performance. It is expected that the PPy/TiO2 composite can be considered as a stable adsorbent for dye removal.

  16. Highly effective adsorption of cationic and anionic dyes on magnetic Fe/Ni nanoparticles doped bimodal mesoporous carbon.

    PubMed

    Liu, Yuanyuan; Zeng, Guangming; Tang, Lin; Cai, Ye; Pang, Ya; Zhang, Yi; Yang, Guide; Zhou, Yaoyu; He, Xiaoxiao; He, Yan

    2015-06-15

    Magnetic Fe/Ni nanoparticles doped bimodal mesoporous carbon (MBMC) was prepared for highly effective adsorption of cationic dye methylene blue (MB) and anionic dye methyl orange (MO). Structure characterization demonstrated that Fe/Ni nanoparticles were embedded into the interior of the mesoprous carbon, and MBMC maintained ordered and bimodal mesopores. The effects of several parameters such as contact time, pH, temperature, ionic strength and dye molecular structure on the adsorption were investigated. Alkaline pH was better for MB adsorption, while acidic pH was more favorable for MO uptake. The adsorption capacity was slightly enhanced when existing ion concentrations increased. Adsorption on MBMC was affected by the molecular structures of different dyes, and both primary and secondary pores of MBMC were involved in dye adsorption. The adsorption kinetics fitted well with pseudo-second-order model and exhibited 3-stage intraparticle diffusion mode. Equilibrium data were best described by Langmuir model, and the estimated maximum adsorption capacity for MB and MO was 959.5mg/g and 849.3mg/g, respectively. Thermodynamic studies indicated that the adsorption process was spontaneous and endothermic. Moreover, the adsorbent could be regenerated using ethanol, and the regenerated adsorbent after seven cycles could retain over 80% of the adsorption capacity for the fresh adsorbent. The results suggested that MBMC could be considered as very effective and promising materials for both anionic and cationic dyes removal from wastewater. PMID:25765736

  17. Microwave-assisted modification on montmorillonite with ester-containing Gemini surfactant and its adsorption behavior for triclosan.

    PubMed

    Liu, Bo; Lu, Junxiang; Xie, Yu; Yang, Bin; Wang, Xiaoying; Sun, Runcang

    2014-03-15

    To obtain effective adsorbent that can remove emerging organic pollutant of triclosan (TCS) in aquatic environment, different ester-containing Gemini surfactant-modified MMT (EMMT) were prepared under microwave irradiation. The whole process was rapid, uniform, easy and energy-efficient. The structures and morphology of EMMT were characterized by XRD, TEM, FT-IR, SEM and TGA. The results revealed that the saturated intercalation amount of this surfactant was 0.8 times to cation exchange capacity (CEC) of MMT, and there was electrostatic interaction between ester-containing Gemini surfactant and MMT. In addition, they bound in the ways of intercalation, intercalation-adsorption or adsorption, which relied on the dosage of the surfactant. The surface of EMMT was hydrophobic, rough and fluffy, which contributed to its strong adsorption capacity. The adsorption equilibrium data of EMMT for TCS were fitted to Langmuir and Freundlich isothermal adsorption model. The result showed that Langmuir isothermal adsorption model could describe the adsorption behavior better, the adsorption behavior of TCS on EMMT was confirmed to a surface monolayer adsorption, and notably the theoretical maximum adsorption capacity was up to 133 mg/g. Therefore, this work lays important foundation on developing effective and safe absorbent materials for the treatment of emerging organic pollutants. PMID:24461850

  18. Adsorption Behaviors of 17α-Ethinylestradiol in Sediment-Water System in Northern Taihu Lake, China

    PubMed Central

    Wang, Yonghua; Hu, Liangfeng; Wang, Qiuying; Lu, Guanghua; Li, Yi

    2014-01-01

    Adsorption behavior of 17α-ethinylestradiol (EE2) in northern Taihu Lake sediment was analyzed by using batch equilibrium experiment. Freundlich isotherm could describe the adsorption thermodynamic behavior of EE2 in sediment. Sediment organic matter (SOM) contents had important impacts on the adsorption capacity for EE2. The pH values also influenced the adsorption capacity for EE2. Increase of pH value could decrease the EE2 adsorption, which might be due to the electrostatic repulsion between the anionic form of EE2 and sediments with negative charge under high pH values. Competitive effects of bisphenol A (BPA) on EE2 adsorption were further analyzed. The results showed that low concentration BPA did not have significant influences on EE2 adsorption. However, high concentration BPA could reduce EE2 adsorption, which might be due to the similar molecular diameter of BPA with adsorption sites and one more benzene ring with a hydroxyl group in BPA. These results provide primary information of EE2 adsorption in sediment-water system in Taihu Lake, which is useful for the environmental risk assessment and management of EE2 in studied area. PMID:25152910

  19. Reaching the Overlooked Student in Physical Education

    ERIC Educational Resources Information Center

    Esslinger, Keri; Esslinger, Travis; Bagshaw, Jarad

    2015-01-01

    This article describes the use of live action role-playing, or "LARPing," as a non-traditional activity that has the potential to reach students who are not interested in traditional physical education.

  20. Chemical Principles Revisited: Using the Equilibrium Concept.

    ERIC Educational Resources Information Center

    Mickey, Charles D., Ed.

    1981-01-01

    Discusses the concept of equilibrium in chemical systems, particularly in relation to predicting the position of equilibrium, predicting spontaneity of a reaction, quantitative applications of the equilibrium constant, heterogeneous equilibrium, determination of the solubility product constant, common-ion effect, and dissolution of precipitates.…