X-36 Tailless Fighter Agility Research Aircraft in flight

NASA Technical Reports Server (NTRS)

1997-01-01

The X-36 technology demonstrator shows off its distinctive shape as the remotely piloted aircraft flies a research mission over the Southern California desert on October 30, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Tailless Fighter Agility Research Aircraft in flight

NASA Technical Reports Server (NTRS)

1997-01-01

The tailless X-36 technology demonstrator research aircraft cruises over the California desert at low altitude during a 1997 research flight. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

ECN-14283

NASA Image and Video Library

1980-12-30

The Highly Maneuverable Aircraft Technology (HiMAT) research vehicle is shown here mated to a wing pylon on NASA’s B-52 mothership aircraft. The HiMAT was a technology demonstrator to test structures and configurations for advanced fighter concepts. Over the course of more than 40 years, the B-52 proved a valuable workhorse for NASA’s Dryden Flight Research Center (under various names), launching a wide variety of vehicles and conducting numerous other research flights.

ARC-1996-AC95-0154-333

NASA Image and Video Library

1996-02-23

CALF/JAST X-32 test program: the LSPM (Large Scale Powered Model), Lockheed's concept for a tri-service aircraft (Air Force, Navy, Marines) CALF (Common Affordable Lightweight Fighter) as part of the Department of Defense's Joint Advanced Strike Technology (JAST) is being tested in the 80x120ft w.t. test-930 with rear horizontal stabilizer

78 FR 29120 - Notice of Intent (NOI) To Prepare an Environmental Impact Statement (EIS) for Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-17

...) for Proposed Establishment and Expansion of Military Airspace in Support of the Oregon Air National Guard (ORANG), Portland International Airport, Portland, and Kingsley Field, Klamath Falls, OR AGENCY... proximity to ORANG flying units to support advanced 21st-century air-to-air tactical fighter technologies...

EC97-44293-3

NASA Image and Video Library

1997-09-29

Four different versions of the F-16 were used by Dryden in the 1990s. On the left and right sides are two F-16XLs. On the left is the F-16XL #2 (NASA 848), which is the two-seat version, used for advanced laminar flow studies until late 1996. On the right is the single-seat F-16XL #1 (NASA 849), used for laminar flow research and sonic boom research. (Laminar flow refers to smooth airflow over a wing, which increases lift and reduces drag compared to turbulent airflow). Between them at center left is an F-16A (NASA 816), the only civilian operated F-16. Next to it at center right is the U.S. Air Force Advance Fighter Technology Integration (AFTI) F-16, a program to test new sensor and control technologies for future fighter aircraft. Both F-16XLs are in storage at Dryden. The F-16A was never flown at Dryden, and was parked by the entrance to the center. The AFTI F-16 is in the Air Force Museum.

EC97-44293-1

NASA Image and Video Library

1997-09-29

Four different versions of the F-16 were used by Dryden in the 1990s. On the left and right sides are two F-16XLs. On the left is the F-16XL #2 (NASA 848), which is the two-seat version, used for advanced laminar flow studies until late 1996. On the right is the single-seat F-16XL #1 (NASA 849), used for laminar flow research and sonic boom research. (Laminar flow refers to smooth airflow over a wing, which increases lift and reduces drag compared to turbulent airflow). Between them at center left is an F-16A (NASA 816), the only civilian operated F-16. Next to it at center right is the U.S. Air Force Advance Fighter Technology Integration (AFTI) F-16, a program to test new sensor and control technologies for future fighter aircraft. Both F-16XLs are in storage at Dryden. The F-16A was never flown at Dryden, and was parked by the entrance to the center. The AFTI F-16 is in the Air Force Museum.

Flight Dynamic Simulation of Fighter In the Asymmetric External Store Release Process

NASA Astrophysics Data System (ADS)

Safi’i, Imam; Arifianto, Ony; Nurohman, Chandra

2018-04-01

In the fighter design, it is important to evaluate and analyze the flight dynamic of the aircraft earlier in the development process. One of the case is the dynamics of external store release process. A simulation tool can be used to analyze the fighter/external store system’s dynamics in the preliminary design stage. This paper reports the flight dynamics of Jet Fighter Experiment (JF-1 E) in asymmetric Advance Medium Range Air to Air Missile (AMRAAM) release process through simulations. The JF-1 E and AIM 120 AMRAAAM models are built by using Advanced Aircraft Analysis (AAA) and Missile Datcom software. By using these softwares, the aerodynamic stability and control derivatives can be obtained and used to model the dynamic characteristic of the fighter and the external store. The dynamic system is modeled by using MATLAB/Simulink software. By using this software, both the fighter/external store integration and the external store release process is simulated, and the dynamic of the system can be analyzed.

Pilot vehicle interface on the advanced fighter technology integration F-16

NASA Technical Reports Server (NTRS)

Dana, W. H.; Smith, W. B.; Howard, J. D.

1986-01-01

This paper focuses on the work load aspects of the pilot vehicle interface in regard to the new technologies tested during AMAS Phase II. Subjects discussed in this paper include: a wide field-of-view head-up display; automated maneuvering attack system/sensor tracker system; master modes that configure flight controls and mission avionics; a modified helmet mounted sight; improved multifunction display capability; a voice interactive command system; ride qualities during automated weapon delivery; a color moving map; an advanced digital map display; and a g-induced loss-of-consciousness and spatial disorientation autorecovery system.

Ergonomics technology

NASA Technical Reports Server (NTRS)

Jones, W. L.

1977-01-01

Major areas of research and development in ergonomics technology for space environments are discussed. Attention is given to possible applications of the technology developed by NASA in industrial settings. A group of mass spectrometers for gas analysis capable of fully automatic operation has been developed for atmosphere control on spacecraft; a version for industrial use has been constructed. Advances have been made in personal cooling technology, remote monitoring of medical information, and aerosol particle control. Experience gained by NASA during the design and development of portable life support units has recently been applied to improve breathing equipment used by fire fighters.

Qualification of the flight-critical AFTI/F-16 digital flight control system. [Advanced Fighter Technology Integration

NASA Technical Reports Server (NTRS)

Mackall, D. A.; Ishmael, S. D.; Regenie, V. A.

1983-01-01

Qualification considerations for assuring the safety of a life-critical digital flight control system include four major areas: systems interactions, verification, validation, and configuration control. The AFTI/F-16 design, development, and qualification illustrate these considerations. In this paper, qualification concepts, procedures, and methodologies are discussed and illustrated through specific examples.

Evolution of Embedded Processing for Wide Area Surveillance

DTIC Science & Technology

2014-01-01

future vision . 15. SUBJECT TERMS Embedded processing; high performance computing; general-purpose graphical processing units (GPGPUs) 16. SECURITY...recon- naissance (ISR) mission capabilities. The capabilities these advancements are achieving include the ability to provide persistent all...fighters to support and positively affect their mission . Significant improvements in high-performance computing (HPC) technology make it possible to

Design of a fifth generation air superiority fighter

NASA Astrophysics Data System (ADS)

Atique, Md. Saifuddin Ahmed; Barman, Shuvrodeb; Nafi, Asif Shahriar; Bellah, Masum; Salam, Md. Abdus

2016-07-01

Air Superiority Fighter is considered to be an effective dogfighter which is stealthy & highly maneuverable to surprise enemy along with improve survivability against the missile fire. This new generation fighter aircraft requires fantastic aerodynamics design, low wing loading (W/S), high thrust to weight ratio (T/W) with super cruise ability. Conceptual design is the first step to design an aircraft. In this paper conceptual design of an Air Superiority Fighter Aircraft is proposed to carry 1 crew member (pilot) that can fly at maximum Mach No of 2.3 covering a range of 1500 km with maximum ceiling of 61,000 ft. Payload capacity of this proposed aircraft is 6000 lb that covers two advanced missiles & one advanced gun. The Air Superiority Fighter Aircraft was designed to undertake all the following missions like: combat air petrol, air to air combat, maritime attack, close air support, suppression, destruction of enemy air defense and reconnaissance.

X-36 Tailless Fighter Agility Research Aircraft in flight

NASA Technical Reports Server (NTRS)

1997-01-01

The lack of a vertical tail on the X-36 technology demonstrator is evident as the remotely piloted aircraft flies a low-altitude research flight above Rogers Dry Lake at Edwards Air Force Base in the California desert on October 30, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

Measuring wildland fire fighter performance with wearable technology.

PubMed

Parker, Richard; Vitalis, Antonios; Walker, Robyn; Riley, David; Pearce, H Grant

2017-03-01

Wildland (rural) fire fighting is a physically demanding and hazardous occupation. An observational study was conducted to explore the use of new technologies for the field study of fire fighters at wildfires and to understand the work pressures of wildland fire fighting. The research was carried out with two fire fighters at real fires wearing microphones, miniature video cameras, heart rate monitors and GPS units to record their actions and location at wildfire events. The fire fighters were exposed to high physiological workloads (heart rates of up to 180 beats per minute) and walked considerable distances at the fires. Results from this study have been used in presentations to fire fighters and non-operational fire personnel to understand the pressures fire fighters are under and how others complete the fire fighting tasks. Copyright © 2016 Elsevier Ltd. All rights reserved.

EC93-41094-4

NASA Image and Video Library

1993-05-18

A NASA F/A-18, specially modified to test the newest and most advanced system technologies, on its first research flight on May 21, 1993, at NASA's Dryden Flight Research Facility, Edwards, California. Flown by Dryden in a multi-year, joint NASA/DOD/industry program, the F/A-18 former Navy fighter was modified into a unique Systems Research Aircraft (SRA) to investigate a host of new technologies in the areas of flight controls, airdata sensing and advanced computing. The primary goal of the SRA program was to validate through flight research cutting-edge technologies which could benefit future aircraft and spacecraft by improving efficiency and performance, reducing weight and complexity, with a resultant reduction on development and operational costs.

AFTI/F16 Automated Maneuvering Attack System Test Reports/Special Technologies and Outlook.

DTIC Science & Technology

1986-07-11

Multiplex Data Bus A-A Air-To-Air A-S Air-to-Surface AFTI Advanced Fighter Technology Integration SYSTEM DESIGN AGL Above-Ground-Level AMAS Automated...Maneuvering Attack System Design requirements for the AFTI/F-16 are driven AMUX Avionics Multiplex Data Bus by realistic air combat scenarios and are...the avionics subsystem IFIM and avionics systems are single-thread, much of the sensed various flight control sensors. Additionally, along with data

Changing the Introduction to Fighter Fundamentals Course for 21st Century F-15C Pilots

DTIC Science & Technology

2016-01-01

IFF model based on the success the USAF has enjoyed in establishing Air Superiority. There is no argument the United States has enjoyed the blanket ...dangerous place and so is the air superiority domain. Our country has gone to great lengths procuring new advanced weapons such as the F-22A and...F-35A, meanwhile updating older aircraft with advanced technology to ensure air dominance.9 So have her near peer adversaries, such as Russia and

Are You Experienced : A Fresh Look at the Fifth-Generation Fighter Experience Model

DTIC Science & Technology

2016-06-01

13 ANALYSIS………………………………………………………………………………………15 Aircraft Utilization Rates………………………………………………………………...15 Fourth and Fifth Generation TTE Comparison... military service, the United States Air Force embodies the advancements of technology available in the modern age. Fighter aircraft are essential to the...pilot to achieve experience is called Time to 7 Experience ( TTE ). This value divided by the number of inexperienced positions is a squadron’s

Tactical STOL moment balance through innovative configuration technology

NASA Technical Reports Server (NTRS)

Eckard, G. J.; Sutton, R. C.; Poth, G. E.

1981-01-01

Innovative and conventional thrust vectoring moment balance mechanisms, as applied to advanced tactical fighters, are examined. The innovative mechanisms include thrust line translation, life line translation, and auxiliary power control; the conventional mechanisms under investigation are horizontal tails, canards, and variable sweep wings. These mechanisms are tested for their ability to provide negative static margins for landing approach or relocation of the vectored thrust line nearer the aircraft's center of gravity. The net pitching moment due to wing, flaps, and vectored thrust lift would then be small, making possible beneficial trim forces from small trimming devices. These innovative mechanisms are, however, possibly heavy and must be evaluated on their complexity, reliability, maintainability, and STOL capabilities. Several candidate fighter configurations are compared and evaluated.

X-36 Tailless Fighter Agility Research Aircraft arrival at Dryden

NASA Technical Reports Server (NTRS)

1996-01-01

The NASA/McDonnell Douglas Corporation (MDC) X-36 Tailless Fighter Agility Research Aircraft in it's hangar at NASA Dryden Flight Research Center, Edwards, California, following its arrival on July 2, 1996. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

Research on Visual Display Integration for Advanced Fighter Aircraft.

DTIC Science & Technology

1978-11-01

V— V . — I 22 February 1979 ERRATA: AMBL-TR-78-97, RESEARC H ON...speculated , the matrix format technologies (plasnias , LC’s, and LED’S) have made significant inroads to the display market for alpha— • numerics and...applications in the consumer/industrial market . Countering the trend a recent article (Reference (61)) indicates some current interest in using a laser

Design study of test models of maneuvering aircraft configurations for the National Transonic Facility (NTF)

NASA Technical Reports Server (NTRS)

Griffin, S. A.; Madsen, A. P.; Mcclain, A. A.

1984-01-01

The feasibility of designing advanced technology, highly maneuverable, fighter aircraft models to achieve full scale Reynolds number in the National Transonic Facility (NTF) is examined. Each of the selected configurations are tested for aeroelastic effects through the use of force and pressure data. A review of materials and material processes is also included.

F-22 cockpit display system

NASA Astrophysics Data System (ADS)

Bailey, David C.

1994-06-01

The F-22 is the first exclusively glass cockpit where all instrumentation has been replaced by displays. The F-22 Engineering and Manufacturing Development Program is implementing the display technology proven during the Advanced Tactical Fighter Demonstration and Validation program. This paper will describe how the F-22 goals have been met and some of the tradeoffs that resulted in the current display design.

Advanced fighter technology integration (AFTI)/F-16 Automated Maneuvering Attack System final flight test results

NASA Technical Reports Server (NTRS)

Dowden, Donald J.; Bessette, Denis E.

1987-01-01

The AFTI F-16 Automated Maneuvering Attack System has undergone developmental and demonstration flight testing over a total of 347.3 flying hours in 237 sorties. The emphasis of this phase of the flight test program was on the development of automated guidance and control systems for air-to-air and air-to-ground weapons delivery, using a digital flight control system, dual avionics multiplex buses, an advanced FLIR sensor with laser ranger, integrated flight/fire-control software, advanced cockpit display and controls, and modified core Multinational Stage Improvement Program avionics.

Reusable Surface Insulation

NASA Technical Reports Server (NTRS)

1997-01-01

Advanced Flexible Reusable Surface Insulation, developed by Ames Research Center, protects the Space Shuttle from the searing heat that engulfs it on reentry into the Earth's atmosphere. Initially integrated into the Space Shuttle by Rockwell International, production was transferred to Hi-Temp Insulation Inc. in 1974. Over the years, Hi-Temp has created many new technologies to meet the requirements of the Space Shuttle program. This expertise is also used commercially, including insulation blankets to cover aircrafts parts, fire barrier material to protect aircraft engine cowlings and aircraft rescue fire fighter suits. A Fire Protection Division has also been established, offering the first suit designed exclusively by and for aircraft rescue fire fighters. Hi-Temp is a supplier to the Los Angeles City Fire Department as well as other major U.S. civil and military fire departments.

Charting a New Path: Modernizing the U.S. Air Force Fighter Pilots Career Development

DTIC Science & Technology

2015-12-01

truly provides no new incentives for undecided fighter pilots and is proving to be an antiquated attempt to maintain the fighter pilot force...growing technological requirements. Weapons shops are responsible for a growing number of responsibilities to support combat operations. Crypto

Next Generation Munitions Handler: Human-Machine Interface and Preliminary Performance Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Draper, J.V.; Jansen, J.F.; Pin, F.G.

1999-04-25

The Next Generation Munitions Handler/Advanced Technology Demonstrator (NGMI-VATTD) is a technology demonstrator for the application of an advanced robotic device for re-arming U.S. Air Force (USAF) and U.S. Navy (USN) tactical fighters. It comprises two key hardware components: a heavy-lift dexterous manipulator (HDM) and a nonholonomic mobility platform. The NGMWATTD is capable of lifting weapons up to 4400 kg (2000 lb) and placing them on any weapons rack on existing fighters (including the F-22 Raptor). This report describes the NGMH mission with particular reference to human-machine interfaces. It also describes preliminary testing to garner feedback about the heavy-lift manipulator armmore » from experienced fighter load crewmen. The purpose of the testing was to provide preliminary information about control system parameters and to gather feed- back from users about manipulator arm functionality. To that end, the Air Force load crewmen interacted with the NGMWATTD in an informal testing session and provided feedback about the performance of the system. Certain con- trol system parameters were changed during the course of the testing and feedback from the participants was used to make a rough estimate of "good" initial operating parameters. Later, formal testing will concentrate within this range to identify optimal operating parameters. User reactions to the HDM were generally positive, All of the USAF personnel were favorably impressed with the capabilities of the system. Fine-tuning operating parameters created a system even more favorably regarded by the load crews. Further adjustment to control system parameters will result in a system that is operationally efficient, easy to use, and well accepted by users.« less

A new flight control and management system architecture and configuration

NASA Astrophysics Data System (ADS)

Kong, Fan-e.; Chen, Zongji

2006-11-01

The advanced fighter should possess the performance such as super-sound cruising, stealth, agility, STOVL(Short Take-Off Vertical Landing),powerful communication and information processing. For this purpose, it is not enough only to improve the aerodynamic and propulsion system. More importantly, it is necessary to enhance the control system. A complete flight control system provides not only autopilot, auto-throttle and control augmentation, but also the given mission management. F-22 and JSF possess considerably outstanding flight control system on the basis of pave pillar and pave pace avionics architecture. But their control architecture is not enough integrated. The main purpose of this paper is to build a novel fighter control system architecture. The control system constructed on this architecture should be enough integrated, inexpensive, fault-tolerant, high safe, reliable and effective. And it will take charge of both the flight control and mission management. Starting from this purpose, this paper finishes the work as follows: First, based on the human nervous control, a three-leveled hierarchical control architecture is proposed. At the top of the architecture, decision level is in charge of decision-making works. In the middle, organization & coordination level will schedule resources, monitor the states of the fighter and switch the control modes etc. And the bottom is execution level which holds the concrete drive and measurement; then, according to their function and resources all the tasks involving flight control and mission management are sorted to individual level; at last, in order to validate the three-leveled architecture, a physical configuration is also showed. The configuration is distributed and applies some new advancement in information technology industry such line replaced module and cluster technology.

X-36 Tailless Fighter Agility Research Aircraft arrival at Dryden

NASA Technical Reports Server (NTRS)

1996-01-01

NASA and McDonnell Douglas Corporation (MDC) personnel remove protective covers from the newly arrived NASA/McDonnell Douglas Corporation X-36 Tailless Fighter Agility Research Aircraft. It arrived at NASA Dryden Flight Research Center, Edwards, California, on July 2, 1996. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Tailless Fighter Agility Research Aircraft arrival at Dryden

NASA Technical Reports Server (NTRS)

1996-01-01

NASA and McDonnell Douglas Corporation (MDC) personnel wait to attach a hoist to the X-36 Tailless Fighter Agility Research Aircraft, which arrived at NASA Dryden Flight Research Center, Edwards, California, on July 2, 1996. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Tailless Fighter Agility Research Aircraft on lakebed during high-speed taxi tests

NASA Technical Reports Server (NTRS)

1996-01-01

The NASA/McDonnell Douglas Corporation (MDC) X-36 Tailless Fighter Agility Research Aircraft undergoes high-speed taxi tests on Rogers Dry Lake at NASA Dryden Flight Research Center, Edwards, California, on October 17, 1996. The aircraft was tested at speeds up to 85 knots. Normal takeoff speed would be 110 knots. More taxi and radio frequency tests were slated before it's first flight would be made. This took place on May 17, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Tailless Fighter Agility Research Aircraft on lakebed during high-speed taxi tests

NASA Technical Reports Server (NTRS)

1996-01-01

The NASA/McDonnell Douglas Corporation (MDC) X-36 Tailless Fighter Agility Research Aircraft undergoes high-speed taxi tests on Rogers Dry Lake at NASA Dryden Flight Research Center, Edwards, California, on October 17, 1996. The aircraft was tested at speeds up to 85 knots. Normal takeoff speed would be 110 knots. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Tailless Fighter Agility Research Aircraft arrival at Dryden

NASA Technical Reports Server (NTRS)

1996-01-01

The NASA/McDonnell Douglas Corporation (MDC) X-36 Tailless Fighter Agility Research Aircraft is steered to it's hangar at NASA Dryden Flight Research Center, Edwards, California, following arrival on July 2, 1996. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

The national aero-space plane

NASA Technical Reports Server (NTRS)

Mendez, Bruce

1988-01-01

The National Aerospace Plane is an extremely versatile and adaptable aircraft. It can be developed into an Orient Express that would dramatically improve trade with countries in Asia and elsewhere: a commuter transport to ferry men and materials to space, an advanced tactical fighter or bomber, and an unparalleled high altitude spy-plane to observe troubled spots all over the globe. Utilizing the technology developed by this pilot program, it will be possible to quickly and easily get to low Earth orbit, go halfway around the world in a fraction of the time it previously took, and lead the world in the development of advanced technology to improve our lives and the lives of many others.

X-36 in Flight over Mojave Desert

NASA Technical Reports Server (NTRS)

1997-01-01

The unusual lines of the X-36 technology demonstrator contrast sharply with the desert floor as the remotely piloted aircraft scoots across the California desert at low altitude during a research flight on October 30, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

Wing planform effects at supersonic speeds for an advanced fighter configuration

NASA Technical Reports Server (NTRS)

Wood, R. M.; Miller, D. S.

1984-01-01

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

X-36 Taking off during First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

The remotely-piloted X-36 Tailless Fighter Agility Research Aircraft lifts off from Rogers Dry Lake at the Dryden Flight Research Center on its first flight on May 17, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

Real-time data display for AFTI/F-16 flight testing

NASA Technical Reports Server (NTRS)

Harney, P. F.

1982-01-01

Advanced fighter technologies to improve air to air and air to surface weapon delivery and survivability is demonstrated. Real time monitoring of aircraft operation during flight testing is necessary not only for safety considerations but also for preliminary evaluation of flight test results. The complexity of the AFTI/F-16 aircraft requires an extensive capability to accomplish real time data goals; that capability and the resultant product are described.

Fiber optic control system integration

NASA Technical Reports Server (NTRS)

Poppel, G. L.; Glasheen, W. M.; Russell, J. C.

1987-01-01

A total fiber optic, integrated propulsion/flight control system concept for advanced fighter aircraft is presented. Fiber optic technology pertaining to this system is identified and evaluated for application readiness. A fiber optic sensor vendor survey was completed, and the results are reported. The advantages of centralized/direct architecture are reviewed, and the concept of the protocol branch is explained. Preliminary protocol branch selections are made based on the F-18/F404 application. Concepts for new optical tools are described. Development plans for the optical technology and the described system are included.

EC86-33385-002

NASA Image and Video Library

1986-02-27

This photograph shows a modified General Dynamics AFTI/F-111A Aardvark in flight with supercritical mission adaptive wings (MAW) installed. With the phasing out of the TACT program came a renewed effort by the Air Force Flight Dynamics Laboratory to extend supercritical wing technology to a higher level of performance. In the early 1980s the supercritical wing on the F-111A aircraft was replaced with a wing built by Boeing Aircraft Company System called a “mission adaptive wing” (MAW), and a joint NASA and Air Force program called Advanced Fighter Technology Integration (AFTI) was born.

Maintenance Metrics for Jovial (J73) Software

DTIC Science & Technology

1988-12-01

pacing technology in advanced fighters, just as it has in most other weapon systems and information systems" ( Canan , 1986:49). Another reason for...the magnitude of the software inside an aircraft may represent only a fraction of that aircraft’s total software requirement." ( Canan , 1986:49) One more...art than a science" marks program development as a largely labor-intensive, human endeavor ( Canan , 1986:50). Individual effort and creativity therefore

X-36 Being Prepared on Lakebed for First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

Lit by the rays of the morning sunrise on Rogers Dry Lake, adjacent to NASA's Dryden Flight Research Center, Edwards, California, technicians prepare the remotely-piloted X-36 Tailless Fighter Agility Research Aircraft for its first flight in May 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 on Ground after Radio and Telemetry Tests

NASA Technical Reports Server (NTRS)

1996-01-01

A UH-1 helicopter lowers the X-36 Tailless Fighter Agility Research Aircraft to the ground after radio frequency and telemetry tests above Rogers Dry Lake at NASA Dryden Flight Research Center, Edwards, California, in November 1996. The purpose of taking the X-36 aloft for the radio and telemetry system checkouts was to test the systems more realistically while airborne. More taxi and radio frequency tests were conducted before the aircraft's first flight in early 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 in Flight over Mojave Desert during 5th Flight

NASA Technical Reports Server (NTRS)

1997-01-01

The unusual lines of the X-36 Tailless Fighter Agility Research Aircraft contrast sharply with the desert floor as the remotely-piloted aircraft flies over the Mojave Desert on a June 1997 research flight. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Carried Aloft by Helicopter during Radio and Telemetry Tests

NASA Technical Reports Server (NTRS)

1996-01-01

A Bell UH-1 helicopter lifts the X-36 Tailless Fighter Agility Research Aircraft off the ground for radio frequency and telemetry tests above Rogers Dry Lake at NASA Dryden Flight Research Center, Edwards, California, in November 1996. The purpose of taking the X-36 aloft for the radio and telemetry system checkouts was to test the systems more realistically while airborne. More taxi and radio frequency tests were conducted before the aircraft's first flight in early 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed/ high angles of attack and at high speed/low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 during First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

The remotely-piloted X-36 Tailless Fighter Agility Research Aircraft climbs out from Rogers Dry Lake at the Dryden Flight Research Center on its first flight in May 1997. The aircraft flew for five minutes and reached an altitude of approximately 4,900 feet. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 in Flight near Edge of Rogers Dry Lake during 5th Flight

NASA Technical Reports Server (NTRS)

1997-01-01

This photo shows the X-36 Tailless Fighter Agility Research Aircraft passing over the edge of Rogers Dry Lake as the remotely-piloted aircraft flies over Edwards Air Force Base on a June 1997 research flight. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Being Prepared on Lakebed for First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

Lit by the rays of the morning sunrise on Rogers Dry Lake, adjacent to NASA's Dryden Flight Research Center, Edwards, California, a technician prepares the remotely-piloted X-36 Tailless Fighter Agility Research Aircraft for its first flight on May 17, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 on Ramp Viewed from Above

NASA Technical Reports Server (NTRS)

1997-01-01

This look-down view of the X-36 Tailless Fighter Agility Research Aircraft on the ramp at NASA's Dryden Flight Research Center, Edwards, California, clearly shows the unusual wing and canard design of the remotely-piloted aircraft. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Being Prepared on Lakebed for First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

Lit by the rays of the morning sunrise on Rogers Dry Lake, adjacent to NASA's Dryden Flight Research Center, Edwards, California, technicians prepares the remotely-piloted X-36 Tailless Fighter Agility Research Aircraft for its first flight on May 17, 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Carried Aloft by Helicopter during Radio and Telemetry Tests

NASA Technical Reports Server (NTRS)

1996-01-01

A Bell UH-1 helicopter lifts the X-36 Tailless Fighter Agility Research Aircraft off the ground for radio frequency and telemetry tests above Rogers Dry Lake at NASA Dryden Flight Research Center, Edwards, California, in November 1996. The purpose of taking the X-36 aloft for the radio and telemetry system checkouts was to test the systems more realistically while airborne. More taxi and radio frequency tests were conducted before the aircraft's first flight in early 1997. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 Being Prepared on Lakebed for First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

As the sun creeps above the horizon of Rogers Dry Lake at NASA's Dryden Flight Research Center, Edwards, California, technicians make final preparations for the first flight of the X-36 Tailless Fighter Agility Research Aircraft. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

X-36 arrival at Dryden

NASA Technical Reports Server (NTRS)

1996-01-01

NASA and McDonnell Douglas Corporation (MDC) personnel steady the X-36 Tailless Fighter Agility Research Aircraft following arrival at NASA Dryden Flight Research Center, Edwards, California, on July 2, 1996. The aircraft is being hoisted out of it's shipping crate. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

The Comanche and the Albatross: About Our Neck Was Hung

DTIC Science & Technology

2014-06-01

aircraft .22 F-35 research, development, test, and evaluation funds are left intact for systems migration and maintenance of the aircraft already...and EPAWSS. c The F-15G (called EF-15E by Boeing) moves the EW systems from the EA-18G to the F-15E+. d New-build aircraft were priced for both...fighter fleet with the F-35A. This stealthy aircraft pos-sessed advanced technology and was no more expensive than the aircraft it was designed to

Nonlinear aerodynamic wing design

NASA Technical Reports Server (NTRS)

Bonner, Ellwood

1985-01-01

The applicability of new nonlinear theoretical techniques is demonstrated for supersonic wing design. The new technology was utilized to define outboard panels for an existing advanced tactical fighter model. Mach 1.6 maneuver point design and multi-operating point compromise surfaces were developed and tested. High aerodynamic efficiency was achieved at the design conditions. A corollary result was that only modest supersonic penalties were incurred to meet multiple aerodynamic requirements. The nonlinear potential analysis of a practical configuration arrangement correlated well with experimental data.

Joint Strike Figher Acquisition: Mature Critical Technologies Needed to Reduce Risks

DTIC Science & Technology

2001-10-01

Reduce Risks GAO-02-39 Report Documentation Page Report Date 00OCT2001 Report Type N/A Dates Covered (from... to) - Title and Subtitle JOINT STRIKE...FIGHTER ACQUISITION: Mature Critical Technologies Needed to Reduce Risks Contract Number Grant Number Program Element Number Author(s) Project...1Joint Strike Fighter Acquisition: Development Schedule Should Be Changed to Reduce Risks (GAO/T-NSIAD-00-132

Alternatives for Modernizing U.S. Fighter Forces

DTIC Science & Technology

2009-05-01

Plans for Modernizing Fighter Forces xS -2. The Possible Role of the F-22 Program in Mitigating the Air Force’s Projected Inventory Shortfall xvi1- 1 ... Northrop Grumman won that competition with its proposal for an aircraft based on the RQ-4 Global Hawk. 38 ALTERNATIVES FOR MODERNIZING U.S. FIGHTER...flyable demonstrator for exploring technologies that could lead to an operational UCAV-N, was rolled out by Northrop Grumman in December 2008. Its

Euler Technology Assessment for Preliminary Aircraft Design-Unstructured/Structured Grid NASTD Application for Aerodynamic Analysis of an Advanced Fighter/Tailless Configuration

NASA Technical Reports Server (NTRS)

Michal, Todd R.

1998-01-01

This study supports the NASA Langley sponsored project aimed at determining the viability of using Euler technology for preliminary design use. The primary objective of this study was to assess the accuracy and efficiency of the Boeing, St. Louis unstructured grid flow field analysis system, consisting of the MACGS grid generation and NASTD flow solver codes. Euler solutions about the Aero Configuration/Weapons Fighter Technology (ACWFT) 1204 aircraft configuration were generated. Several variations of the geometry were investigated including a standard wing, cambered wing, deflected elevon, and deflected body flap. A wide range of flow conditions, most of which were in the non-linear regimes of the flight envelope, including variations in speed (subsonic, transonic, supersonic), angles of attack, and sideslip were investigated. Several flowfield non-linearities were present in these solutions including shock waves, vortical flows and the resulting interactions. The accuracy of this method was evaluated by comparing solutions with test data and Navier-Stokes solutions. The ability to accurately predict lateral-directional characteristics and control effectiveness was investigated by computing solutions with sideslip, and with deflected control surfaces. Problem set up times and computational resource requirements were documented and used to evaluate the efficiency of this approach for use in the fast paced preliminary design environment.

EC86-33385-04

NASA Image and Video Library

1986-03-27

This photograph shows a modified General Dynamics AFTI/F-111A Aardvark with supercritical mission adaptive wings (MAW) installed. The AFTI/F111A is seen banking towards Rodgers Dry Lake and Edwards Air Force Base. With the phasing out of the TACT program came a renewed effort by the Air Force Flight Dynamics Laboratory to extend supercritical wing technology to a higher level of performance. In the early 1980s the supercritical wing on the F-111A aircraft was replaced with a wing built by Boeing Aircraft Company System called a “mission adaptive wing” (MAW), and a joint NASA and Air Force program called Advanced Fighter Technology Integration (AFTI) was born.

Military and Government Applications of Human-Machine Communication by Voice

NASA Astrophysics Data System (ADS)

Weinstein, Clifford J.

1995-10-01

This paper describes a range of opportunities for military and government applications of human-machine communication by voice, based on visits and contacts with numerous user organizations in the United States. The applications include some that appear to be feasible by careful integration of current state-of-the-art technology and others that will require a varying mix of advances in speech technology and in integration of the technology into applications environments. Applications that are described include (1) speech recognition and synthesis for mobile command and control; (2) speech processing for a portable multifunction soldier's computer; (3) speech- and language-based technology for naval combat team tactical training; (4) speech technology for command and control on a carrier flight deck; (5) control of auxiliary systems, and alert and warning generation, in fighter aircraft and helicopters; and (6) voice check-in, report entry, and communication for law enforcement agents or special forces. A phased approach for transfer of the technology into applications is advocated, where integration of applications systems is pursued in parallel with advanced research to meet future needs.

X-36 Taking off During First Flight

NASA Technical Reports Server (NTRS)

1997-01-01

The X-36 remotely piloted aircraft lifts off on its first flight, May 17, 1997, at NASA's Dryden Flight Research Center, Edwards, California. The aircraft flew for five minutes and reached an altitude of approximately 4,900 feet. The NASA/Boeing X-36 Tailless Fighter Agility Research Aircraft program successfully demonstrated the tailless fighter design using advanced technologies to improve the maneuverability and survivability of possible future fighter aircraft. The program met or exceeded all project goals. For 31 flights during 1997 at the Dryden Flight Research Center, Edwards, California, the project team examined the aircraft's agility at low speed / high angles of attack and at high speed / low angles of attack. The aircraft's speed envelope reached up to 206 knots (234 mph). This aircraft was very stable and maneuverable. It handled very well. The X-36 vehicle was designed to fly without the traditional tail surfaces common on most aircraft. Instead, a canard forward of the wing was used as well as split ailerons and an advanced thrust-vectoring nozzle for directional control. The X-36 was unstable in both pitch and yaw axes, so an advanced, single-channel digital fly-by-wire control system (developed with some commercially available components) was put in place to stabilize the aircraft. Using a video camera mounted in the nose of the aircraft and an onboard microphone, the X-36 was remotely controlled by a pilot in a ground station virtual cockpit. A standard fighter-type head-up display (HUD) and a moving-map representation of the vehicle's position within the range in which it flew provided excellent situational awareness for the pilot. This pilot-in-the-loop approach eliminated the need for expensive and complex autonomous flight control systems and the risks associated with their inability to deal with unknown or unforeseen phenomena in flight. Fully fueled the X-36 prototype weighed approximately 1,250 pounds. It was 19 feet long and three feet high with a wingspan of just over 10 feet. A Williams International F112 turbofan engine provided close to 700 pounds of thrust. A typical research flight lasted 35 to 45 minutes from takeoff to touchdown. A total of 31 successful research flights were flown from May 17, 1997, to November 12, 1997, amassing 15 hours and 38 minutes of flight time. The aircraft reached an altitude of 20,200 feet and a maximum angle of attack of 40 degrees. In a follow-on effort, the Air Force Research Laboratory (AFRL), Wright-Patterson Air Force Base, Ohio, contracted with Boeing to fly AFRL's Reconfigurable Control for Tailless Fighter Aircraft (RESTORE) software as a demonstration of the adaptability of the neural-net algorithm to compensate for in-flight damage or malfunction of effectors, such as flaps, ailerons and rudders. Two RESTORE research flights were flown in December 1998, proving the viability of the software approach. The X-36 aircraft flown at the Dryden Flight Research Center in 1997 was a 28-percent scale representation of a theoretical advanced fighter aircraft. The Boeing Phantom Works (formerly McDonnell Douglas) in St. Louis, Missouri, built two of the vehicles in a cooperative agreement with the Ames Research Center, Moffett Field, California.

The life and death of ATR/sensor fusion and the hope for resurrection

NASA Astrophysics Data System (ADS)

Rogers, Steven K.; Sadowski, Charles; Bauer, Kenneth W.; Oxley, Mark E.; Kabrisky, Matthew; Rogers, Adam; Mott, Stephen D.

2008-04-01

For over half a century, scientists and engineers have worked diligently to advance computational intelligence. One application of interest is how computational intelligence can bring value to our war fighters. Automatic Target Recognition (ATR) and sensor fusion efforts have fallen far short of the desired capabilities. In this article we review the capabilities requested by war fighters. When compared to our current capabilities, it is easy to conclude current Combat Identification (CID) as a Family of Systems (FoS) does a lousy job. The war fighter needed capable, operationalized ATR and sensor fusion systems ten years ago but it did not happen. The article reviews the war fighter needs and the current state of the art. The article then concludes by looking forward to where we are headed to provide the capabilities required.

Recent flight-test results of optical airdata techniques

NASA Technical Reports Server (NTRS)

Bogue, Rodney K.

1993-01-01

Optical techniques for measuring airdata parameters were demonstrated with promising results on high performance fighter aircraft. These systems can measure the airspeed vector, and some are not as dependent on special in-flight calibration processes as current systems. Optical concepts for measuring freestream static temperature and density are feasible for in-flight applications. The best feature of these concepts is that the air data measurements are obtained nonintrusively, and for the most part well into the freestream region of the flow field about the aircraft. Current requirements for measuring air data at high angle of attack, and future need to measure the same information at hypersonic flight conditions place strains on existing techniques. Optical technology advances show outstanding potential for application in future programs and promise to make common use of optical concepts a reality. Results from several flight-test programs are summarized, and the technology advances required to make optical airdata techniques practical are identified.

A NASA study of the impact of technology on future carrier based tactical aircraft - Overview

NASA Technical Reports Server (NTRS)

Wilson, S. B., III

1992-01-01

This paper examines the impact of technology on future carrier based tactical aircraft. The results were used in the Center for Naval Analysis Future Carrier Study. The NASA Team designed three classes of aircraft ('Fighter', 'Attack', and 'Multimission') with two different technology levels. The Multimission aircraft were further analyzed by examining the penalty on the aircraft for both catapult launch/arrested landing recovery (Cat/trap) and short take-off/vertical landing (STOVL). The study showed the so-called STOVL penalty was reduced by engine technology and the next generation Strike Fighter will pay more penalty for Cat/trap than for STOVL capability.

A Service in Transition: Forging an Integrated Institutional Identity for the United States Air Force

DTIC Science & Technology

2010-06-01

Jr (Bomber) o Seventh Air Force, LTG Jeffrey A. Remington (Fighter) o Eleventh Air Force, LTG Dana T. Atkins (Fighter) o Thirteenth Air Force, LTG...Acculturation.‖ In Handbook of Socialization: Theory and Research, edited by Joan E. Grusec, and Paul D. Hastings, 543-560. New York, NY: Guilford...Philip. ―Determinism and Indeterminacy in the History of Technology.‖ In Does Technology Drive History?, edited by Merritt Roe Smith, and Leo Marx

Computational Fluid Dynamics of Whole-Body Aircraft

NASA Astrophysics Data System (ADS)

Agarwal, Ramesh

1999-01-01

The current state of the art in computational aerodynamics for whole-body aircraft flowfield simulations is described. Recent advances in geometry modeling, surface and volume grid generation, and flow simulation algorithms have led to accurate flowfield predictions for increasingly complex and realistic configurations. As a result, computational aerodynamics has emerged as a crucial enabling technology for the design and development of flight vehicles. Examples illustrating the current capability for the prediction of transport and fighter aircraft flowfields are presented. Unfortunately, accurate modeling of turbulence remains a major difficulty in the analysis of viscosity-dominated flows. In the future, inverse design methods, multidisciplinary design optimization methods, artificial intelligence technology, and massively parallel computer technology will be incorporated into computational aerodynamics, opening up greater opportunities for improved product design at substantially reduced costs.

Results of recent NASA studies on automatic spin prevention for fighter aircraft

NASA Technical Reports Server (NTRS)

Chambers, J. R.; Nguyen, L. T.

1976-01-01

A broad based research program was developed to eliminate or minimize inadvertent spins for advanced military aircraft. Recent piloted simulator studies and airplane flight tests have demonstrated that the automatic control systems in use on current fighters can be tailored to provide a high degree of spin resistance for some configurations without restrictions to maneuverability. Such systems result in greatly increased tactical effectiveness, safety, and pilot confidence.

Military and government applications of human-machine communication by voice.

PubMed Central

Weinstein, C J

1995-01-01

This paper describes a range of opportunities for military and government applications of human-machine communication by voice, based on visits and contacts with numerous user organizations in the United States. The applications include some that appear to be feasible by careful integration of current state-of-the-art technology and others that will require a varying mix of advances in speech technology and in integration of the technology into applications environments. Applications that are described include (1) speech recognition and synthesis for mobile command and control; (2) speech processing for a portable multifunction soldier's computer; (3) speech- and language-based technology for naval combat team tactical training; (4) speech technology for command and control on a carrier flight deck; (5) control of auxiliary systems, and alert and warning generation, in fighter aircraft and helicopters; and (6) voice check-in, report entry, and communication for law enforcement agents or special forces. A phased approach for transfer of the technology into applications is advocated, where integration of applications systems is pursued in parallel with advanced research to meet future needs. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 PMID:7479718

A Comprehensive Review of Firefighter Post-Secondary Training and Education in Florida. Program Review Report.

ERIC Educational Resources Information Center

Florida State Dept. of Education, Tallahassee. Div. of Vocational, Adult, and Community Education.

Florida's community college and school district postsecondary adult vocational programs in fire fighter training and fire science technology were subjected to a statewide program review. Efforts were made to reach Florida's entire community of career and volunteer fire fighters. Data were collected in the following ways: site interviews with…

Rockets for spin recovery

NASA Technical Reports Server (NTRS)

Whipple, R. D.

1980-01-01

The potential effectiveness of rockets as an auxiliary means for an aircraft to effect recovery from spins was investigated. The advances in rocket technology produced by the space effort suggested that currently available systems might obviate many of the problems encountered in earlier rocket systems. A modern fighter configuration known to exhibit a flat spin mode was selected. An analytical study was made of the thrust requirements for a rocket spin recovery system for the subject configuration. These results were then applied to a preliminary systems study of rocket components appropriate to the problem. Subsequent spin tunnel tests were run to evaluate the analytical results.

X-29A flight control system performance during flight test

NASA Technical Reports Server (NTRS)

Chin, J.; Chacon, V.; Gera, J.

1987-01-01

An account is given of flight control system performance results for the X-29A forward-swept wing 'Advanced Technology Demonstrator' fighter aircraft, with attention to its software and hardware components' achievement of the requisite levels of system stability and desirable aircraft handling qualities. The Automatic Camber Control Logic is found to be well integrated with the stability loop of the aircraft. A number of flight test support software programs developed by NASA facilitated monitoring of the X-29A's stability in real time, and allowed the test team to clear the envelope with confidence.

Aerodynamic configuration development of the highly maneuverable aircraft technology remotely piloted research vehicle

NASA Technical Reports Server (NTRS)

Gingrich, P. B.; Child, R. D.; Panageas, G. N.

1977-01-01

The aerodynamic development of the highly maneuverable aircraft technology remotely piloted research vehicle (HiMAT/RPRV) from the conceptual design to the final configuration is presented. The design integrates several advanced concepts to achieve a high degree of transonic maneuverability, and was keyed to sustained maneuverability goals while other fighter typical performance characteristics were maintained. When tests of the baseline configuration indicated deficiencies in the technology integration and design techniques, the vehicle was reconfigured to satisfy the subcritical and supersonic requirements. Drag-due-to-lift levels only 5 percent higher than the optimum were obtained for the wind tunnel model at a lift coefficient of 1 for Mach numbers of up to 0.8. The transonic drag rise was progressively lowered with the application of nonlinear potential flow analyses coupled with experimental data.

A technique for the assessment of fighter aircraft precision controllability

NASA Technical Reports Server (NTRS)

Sisk, T. R.

1978-01-01

Today's emerging fighter aircraft are maneuvering as well at normal accelerations of 7 to 8 g's as their predecessors did at 4 to 5 g's. This improved maneuvering capability has significantly expanded their operating envelope and made the task of evaluating handling qualities more difficult. This paper describes a technique for assessing the precision controllability of highly maneuverable aircraft, a technique that was developed to evaluate the effects of buffet intensity on gunsight tracking capability and found to be a useful tool for the general assessment of fighter aircraft handling qualities. It has also demonstrated its usefulness for evaluating configuration and advanced flight control system refinements. This technique is believed to have application to future aircraft dynamics and pilot-vehicle interface studies.

Study of aerodynamic technology for VSTOL fighter attack aircraft

NASA Technical Reports Server (NTRS)

Burhans, W., Jr.; Crafta, V. J., Jr.; Dannenhoffer, N.; Dellamura, F. A.; Krepski, R. E.

1978-01-01

Vertical short takeoff aircraft capability, supersonic dash capability, and transonic agility were investigated for the development of Fighter/attack aircraft to be accommodated on ships smaller than present aircraft carriers. Topics covered include: (1) description of viable V/STOL fighter/attack configuration (a high wing, close-coupled canard, twin-engine, control configured aircraft) which meets or exceeds specified levels of vehicle performance; (2) estimates of vehicle aerodynamic characteristics and the methodology utilized to generate them; (3) description of propulsion system characteristics and vehicle mass properties; (4) identification of areas of aerodynamic uncertainty; and (5) a test program to investigate the areas of aerodynamic uncertainty in the conventional flight mode.

Workshop on Design Loads for Advanced Fighters: Meeting of the Structures and Materials Panel of AGARD (64th) Held in Madrid (Spain) on 27 April-1 May 1987.

DTIC Science & Technology

1988-02-01

capabilities at the start of a programme. ,Z _ 1. Introduction The flight manoeuvre loads are major design criteria for agile aircraft (aerobatic...E. Van Patten, Ph.D. Armstrong Aerospace Medical Research Laboratory Wright-Patterson AFB, OH 45433-6573 USA INTRODUCTION ~ urrent Fighter...anticipated usage. Also, compliance with each condition mit he verified by analysis, model test, or full scale measurement. INTRODUCTION During the

Fighting Testing ACAT/FRRP: Automatic Collision Avoidance Technology/Fighter Risk Reduction Project

NASA Technical Reports Server (NTRS)

Skoog, Mark A.

2009-01-01

This slide presentation reviews the work of the Flight testing Automatic Collision Avoidance Technology/Fighter Risk Reduction Project (ACAT/FRRP). The goal of this project is to develop common modular architecture for all aircraft, and to enable the transition of technology from research to production as soon as possible to begin to reduce the rate of mishaps. The automated Ground Collision Avoidance System (GCAS) system is designed to prevent collision with the ground, by avionics that project the future trajectory over digital terrain, and request an evasion maneuver at the last instance. The flight controls are capable of automatically performing a recovery. The collision avoidance is described in the presentation. Also included in the presentation is a description of the flight test.

A comparison of theoretical and experimental pressure distributions for two advanced fighter wings

NASA Technical Reports Server (NTRS)

Haney, H. P.; Hicks, R. M.

1981-01-01

A comparison was made between experimental pressure distributions measured during testing of the Vought A-7 fighter and the theoretical predictions of four transonic potential flow codes. Isolated wind and three wing-body codes were used for comparison. All comparisons are for transonic Mach numbers and include both attached and separate flows. In general, the wing-body codes gave better agreement with the experiment than did the isolated wing code but, because of the greater complexity of the geometry, were found to be considerably more expensive and less reliable.

Investigation of trailing-edge-flap, spanwise-blowing concepts on an advanced fighter configuration

NASA Technical Reports Server (NTRS)

Paulson, J. W., Jr.; Quinto, P. F.; Banks, D. W.

1984-01-01

The aerodynamic effects of spanwise blowing on the trailing edge flap of an advanced fighter aircraft configuration were determined in the 4 by 7 Meter Tunnel. A series of tests were conducted with variations in spanwise-blowing vector angle, nozzle exit area, nozzle location, thrust coefficient, and flap deflection in order to determine a superior configuration for both an underwing cascade concept and an overwing port concept. This screening phase of the testing was conducted at a nominal approach angle of attack from 12 deg to 16 deg; and then the superior configurations were tested over a more complete angle of attack range from 0 deg to 20 deg at tunnel free stream dynamic pressures from 20 to 40 lbf/sq ft at thrust coefficients from 0 to 2.

Piloted evaluation of an integrated propulsion and flight control simulator

NASA Technical Reports Server (NTRS)

Bright, Michelle M.; Simon, Donald L.

1992-01-01

A piloted evaluation of the integrated flight and propulsion control simulator for advanced integrated propulsion and airframe control design is described. The evaluation will cover control effector gains and deadbands, control effectiveness and control authority, and heads up display functionality. For this evaluation the flight simulator is configured for transition flight using an advanced Short Take-Off and Vertical Landing fighter aircraft model, a simplified high-bypass turbofan engine model, fighter cockpit displays, and pilot effectors. The piloted tasks used for rating displays and control effector gains are described. Pilot comments and simulation results confirm that the display symbology and control gains are very adequate for the transition flight task. Additionally, it is demonstrated that this small-scale, fixed base flight simulator facility can adequately perform a real time, piloted control evaluation.

Development of an integrated set of research facilities for the support of research flight test

NASA Technical Reports Server (NTRS)

Moore, Archie L.; Harney, Constance D.

1988-01-01

The Ames-Dryden Flight Research Facility (DFRF) serves as the site for high-risk flight research on many one-of-a-kind test vehicles like the X-29A advanced technology demonstrator, F-16 advanced fighter technology integration (AFTI), AFTI F-111 mission adaptive wing, and F-18 high-alpha research vehicle (HARV). Ames-Dryden is on a section of the historic Muroc Range. The facility is oriented toward the testing of high-performance aircraft, as shown by its part in the development of the X-series aircraft. Given the cost of research flight tests and the complexity of today's systems-driven aircraft, an integrated set of ground support experimental facilities is a necessity. In support of the research flight test of highly advanced test beds, the DFRF is developing a network of facilities to expedite the acquisition and distribution of flight research data to the researcher. The network consists of an array of experimental ground-based facilities and systems as nodes and the necessary telecommunications paths to pass research data and information between these facilities. This paper presents the status of the current network, an overview of current developments, and a prospectus on future major enhancements.

A review of technologies applicable to low-speed flight of high-performance aircraft investigated in the Langley 14- x 22-foot subsonic tunnel

NASA Technical Reports Server (NTRS)

Paulson, John W., Jr.; Quinto, P. Frank; Banks, Daniel W.; Kemmerly, Guy T.; Gatlin, Gregory M.

1988-01-01

An extensive research program has been underway at the NASA Langley Research Center to define and develop the technologies required for low-speed flight of high-performance aircraft. This 10-year program has placed emphasis on both short takeoff and landing (STOL) and short takeoff and vertical landing (STOVL) operations rather than on regular up and away flight. A series of NASA in-house as well as joint projects have studied various technologies including high lift, vectored thrust, thrust-induced lift, reversed thrust, an alternate method of providing trim and control, and ground effects. These technologies have been investigated on a number of configurations ranging from industry designs for advanced fighter aircraft to generic wing-canard research models. Test conditions have ranged from hover (or static) through transition to wing-borne flight at angles of attack from -5 to 40 deg at representative thrust coefficients.

HIMAT Inlet Model in the 8- by 6-Foot Supersonic Wind Tunnel

NASA Image and Video Library

1979-02-21

A Highly Maneuverable Aircraft Technology (HiMAT) inlet model installed in the test section of the 8- by 6-Foot Supersonic Wind Tunnel at the National Aeronautics and Space Administration (NASA) Lewis Research Center. Engineers at the Ames Research Center, Dryden Flight Research Center, and Rockwell International designed two pilotless subscale HiMAT vehicles in the mid-1970s to study new design concepts for fighter aircraft in the transonic realm without risking the lives of test pilots. The aircraft used sophisticated technologies such as advanced aerodynamics, composite materials, digital integrated propulsion control, and digital fly-by-wire control systems. In late 1977 NASA Lewis studied the HiMAT’s General Electric J85-21 jet engine in the Propulsion Systems Laboratory. The researchers charted the inlet quality with various combinations anti-distortion screens. HiMAT employed a relatively short and curved inlet compared to actual fighter jets. In the spring of 1979, Larry Smith led an in-depth analysis of the HiMAT inlet in the 8- by 6 tunnel. The researchers installed vortex generators to battle flow separation in the diffuser. The two HiMAT aircraft performed 11 hours of flying over the course of 26 missions from mid-1979 to January 1983 at Dryden and Ames. Although the HiMAT vehicles were considered to be overly complex and expensive, the program yielded a wealth of data that would validate computer-based design tools.

STOVL aircraft simulation for integrated flight and propulsion control research

NASA Technical Reports Server (NTRS)

Mihaloew, James R.; Drummond, Colin K.

1989-01-01

The United States is in the initial stages of committing to a national program to develop a supersonic short takeoff and vertical landing (STOVL) aircraft. The goal of the propulsion community in this effort is to have the enabling propulsion technologies for this type aircraft in place to permit a low risk decision regarding the initiation of a research STOVL supersonic attack/fighter aircraft in the late mid-90's. This technology will effectively integrate, enhance, and extend the supersonic cruise, STOVL and fighter/attack programs to enable U.S. industry to develop a revolutionary supersonic short takeoff and vertical landing fighter/attack aircraft in the post-ATF period. A joint NASA Lewis and NASA Ames research program, with the objective of developing and validating technology for integrated-flight propulsion control design methodologies for short takeoff and vertical landing (STOVL) aircraft, was planned and is underway. This program, the NASA Supersonic STOVL Integrated Flight-Propulsion Controls Program, is a major element of the overall NASA-Lewis Supersonic STOVL Propulsion Technology Program. It uses an integrated approach to develop an integrated program to achieve integrated flight-propulsion control technology. Essential elements of the integrated controls research program are realtime simulations of the integrated aircraft and propulsion systems which will be used in integrated control concept development and evaluations. This paper describes pertinent parts of the research program leading up to the related realtime simulation development and remarks on the simulation structure to accommodate propulsion system hardware drop-in for real system evaluation.

Varo-achro-phobia: the fear of broad spectrum zoom optics

NASA Astrophysics Data System (ADS)

Vogel, Steven; Pollica, Naomi

2015-05-01

Today's battlefield is evolving at light speed. Our war fighters are being tasked with highly complex missions requiring the very best technology our industry can offer. The demand for advanced ISR platforms is challenging designers and engineers in the optics industry to push the envelope and develop wider band solutions to support multiple and broadband sensor platforms. Recently, significant attention has been directed towards the development of optical systems that enable simultaneous operation in the visible and shortwave infrared spectral wavebands. This paper will present a review of the evolution of StingRay Optics' GhostSight™ continuous zoom optics that offer broad chromatic imaging capabilities from the visible through the shortwave infrared spectrum.

Variable-camber systems integration and operational performance of the AFTI/F-111 mission adaptive wing

NASA Technical Reports Server (NTRS)

Smith, John W.; Lock, Wilton P.; Payne, Gordon A.

1992-01-01

The advanced fighter technology integration, the AFTI/F-111 aircraft, is a preproduction F-111A testbed research airplane that was fitted with a smooth variable-camber mission adaptive wing. The camber was positioned and controlled by flexing the upper skins through rotary actuators and linkages driven by power drive units. The wing camber and control system are described. The measured servoactuator frequency responses are presented along with analytical predictions derived from the integrated characteristics of the control elements. A mission adaptive wing system chronology is used to illustrate and assess the reliability and dependability of the servoactuator system during 1524 hours of ground tests and 145 hours of flight testing.

EC93-42065-5

NASA Image and Video Library

1993-07-12

NASA's F/A-18 Hornet is seen here in a banked turn over Rogers Dry Lake in the Mojave desert on an early research flight. It was flown by NASA's Dryden Flight Research Center, Edwards, California, in a multi-year, joint NASA/DOD/industry program, the former Navy fighter was modified into a unique Systems Research Aircraft (SRA) to investigate a host of new technologies in the areas of flight controls, airdata sensing and advanced computing. One of the more than 20 experiments tested aboard the SRA F-18 was an advanced air data sensing system which used a group of pressure taps flush-mounted on the forward fuselage to measure both altitude and wind speed and direction--critical data for flight control and research investigations. The Real-Time Flush Air Data Sensing system concept was evaluated for possible use on the X-33 and X-34 resuable space-launch vehicles. The primary goal of the SRA program was to validate through flight research cutting-edge technologies which could benefit future aircraft and spacecraft by improving efficiency and performance, reducing weight and complexity, with a resultant reduction on development and operational costs.

Stealth Aircraft Technology. (Latest Citations from the Aerospace Database)

NASA Technical Reports Server (NTRS)

1995-01-01

The bibliography contains citations concerning design, manufacture, and history of aircraft incorporating stealth technology. Citations focus on construction materials, testing, aircraft performance, and technology assessment. Fighter aircraft, bombers, missiles, and helicopters represent coverage. (Contains 50-250 citations and includes a subject term index and title list.)

Preliminary design of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter aircraft

NASA Technical Reports Server (NTRS)

Cox, Brian; Borchers, Paul; Gomer, Charlie; Henderson, Dean; Jacobs, Tavis; Lawson, Todd; Peterson, Eric; Ross, Tweed, III; Bellmard, Larry

1990-01-01

The preliminary design study of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter is presented. A brief historical survey of powered lift vehicles was presented, followed by a technology assessment of the latest supersonic STOVL engine cycles under consideration by industry and government in the U.S. and UK. A survey of operational fighter/attack aircraft and the modern battlefield scenario were completed to develop, respectively, the performance requirements and mission profiles for the study. Three configurations were initially investigated with the following engine cycles: a hybrid fan vectored thrust cycle, a lift+lift/cruise cycle, and a mixed flow vectored thrust cycle. The lift+lift/cruise aircraft configuration was selected for detailed design work which consisted of: (1) a material selection and structural layout, including engine removal considerations, (2) an aircraft systems layout, (3) a weapons integration model showing the internal weapons bay mechanism, (4) inlet and nozzle integration, (5) an aircraft suckdown prediction, (6) an aircraft stability and control analysis, including a takeoff, hover, and transition control analysis, (7) a performance and mission capability study, and (8) a life cycle cost analysis. A supersonic fighter aircraft with STOVL capability with the lift+lift/cruise engine cycle seems a viable option for the next generation fighter.

Study of aerodynamic technology for single-cruise-engine VSTOL fighter/attack aircraft, phase 1

NASA Technical Reports Server (NTRS)

Foley, W. H.; Sheridan, A. E.; Smith, C. W.

1982-01-01

A conceptual design and analysis on a single engine VSTOL fighter/attack aircraft is completed. The aircraft combines a NASA/deHavilland ejector with vectored thrust and is capable of accomplishing the mission and point performance of type Specification 169, and a flight demonstrator could be built with an existing F101/DFE engine. The aerodynamic, aero/propulsive, and propulsive uncertainties are identified, and a wind tunnel program is proposed to address those uncertainties associated with wing borne flight.

The Space Laser Business Model

NASA Technical Reports Server (NTRS)

2005-01-01

Creating long-duration, high-powered lasers, for satellites, that can withstand the type of optical misalignment and damage dished out by the unforgiving environment of space, is work that is unique to NASA. It is complicated, specific work, where each step forward is into uncharted territory. In the 1990s, as this technology was first being created, NASA gave free reign to a group of "laser jocks" to develop their own business model and supply the Space Agency with the technology it needed. It was still to be a part of NASA as a division of Goddard Space Flight Center, but would operate independently out of a remote office. The idea for this satellite laboratory was based on the Skunk Works concept at Lockheed Martin Corporation. Formerly known as the Lockheed Corporation, in 1943, the aerospace firm, realizing that the type of advanced research it needed done could not be performed within the confines of a larger company, allowed a group of researchers and engineers to essentially run their own microbusiness without the corporate oversight. The Skunk Works project, in Burbank, California, produced America s first jet fighter, the world s most successful spy plane (U-2), the first 3-times-the-speed-of-sound surveillance aircraft, and the F-117A Nighthawk Stealth Fighter. Boeing followed suit with its Phantom Works, an advanced research and development branch of the company that operates independent of the larger unit and is responsible for a great deal of its most cutting-edge research. NASA s version of this advanced business model was the Space Lidar Technology Center (SLTC), just south of Goddard, in College Park, Maryland. Established in 1998 under a Cooperative Agreement between Goddard and the University of Maryland s A. James Clark School of Engineering, it was a high-tech laser shop where a small group of specialists, never more than 20 employees, worked all hours of the day and night to create the cutting- edge technology the Agency required of them. Drs. Robert Afzal and Joseph Dallas were directors of the SLTC, and led the development and production of active spaceborne, remote-sensing, optical instruments. As a pioneer in the area of photonics, Dr. Dallas led basic research, development, and production of semiconductor laser diode products, improving coupling efficiency through novel physical optics modeling and intracavity phase-correction techniques. He worked for NASA for 15 years, 11 of which were as a civil servant, and 4 of which were as a contractor.

EC85-33205-07

NASA Image and Video Library

1985-10-18

This photograph shows a modified General Dynamics AFTI/F-111A Aardvark with supercritical mission adaptive wings (MAW) installed. The four dark bands on the right wing are the locations of pressure orifices used to measure surface pressures and shock locations on the MAW. The El Paso Mountains and Red Rock Canyon State Park Califonia, about 30 miles northwest of Edwards Air Force Base, are seen directly in the background. With the phasing out of the TACT program came a renewed effort by the Air Force Flight Dynamics Laboratory to extend supercritical wing technology to a higher level of performance. In the early 1980s the supercritical wing on the F-111A aircraft was replaced with a wing built by Boeing Aircraft Company System called a “mission adaptive wing” (MAW), and a joint NASA and Air Force program called Advanced Fighter Technology Integration (AFTI) was born.

Piloted evaluation of an integrated propulsion and flight control simulator

NASA Technical Reports Server (NTRS)

Bright, Michelle M.; Simon, Donald L.

1992-01-01

This paper describes a piloted evaluation of the integrated flight and propulsion control simulator at NASA Lewis Research Center. The purpose of this evaluation is to demonstrate the suitability and effectiveness of this fixed based simulator for advanced integrated propulsion and airframe control design. The evaluation will cover control effector gains and deadbands, control effectiveness and control authority, and heads up display functionality. For this evaluation the flight simulator is configured for transition flight using an advanced Short Take-Off and vertical Landing fighter aircraft model, a simplified high-bypass turbofan engine model, fighter cockpit, displays, and pilot effectors. The paper describes the piloted tasks used for rating displays and control effector gains. Pilot comments and simulation results confirm that the display symbology and control gains are very adequate for the transition flight task. Additionally, it is demonstrated that this small-scale, fixed base flight simulator facility can adequately perform a real time, piloted control evaluation.

Study of aerodynamic technology for VSTOL fighter/attack aircraft: Horizontal attitude concept

NASA Technical Reports Server (NTRS)

Brown, S. H.

1978-01-01

A horizontal attitude VSTOL (HAVSTOL) supersonic fighter attack aircraft powered by RALS turbofan propulsion system is analyzed. Reaction control for subaerodynamic flight is obtained in pitch and yaw from the RALS and roll from wingtip jets powered by bleed air from the RALS duct. Emphasis is placed on the development of aerodynamic characteristics and the identification of aerodynamic uncertainties. A wind tunnel program is shown to resolve some of the uncertainties. Aerodynamic data developed are static characteristics about all axes, control effectiveness, drag, propulsion induced effects and reaction control characteristics.

THE GRAY THREAT. Assessing the Next-Generation European Fighters,

DTIC Science & Technology

1995-01-01

magnitude levels substantially, al- though operationally significant benefits against advanced threats are likely only from a narrow forward sector . EF...operationally sig- nificant benefits against advanced radar threats are likely only from a narrow forward sector . Company literature also points to...the industrial sector . Industrial capabilities will be maintained, all procurement programs will be kept up ... The first choice is to give

Geometry definition and grid generation for a complete fighter aircraft

NASA Technical Reports Server (NTRS)

Edwards, T. A.

1986-01-01

Recent advances in computing power and numerical solution procedures have enabled computational fluid dynamicists to attempt increasingly difficult problems. In particular, efforts are focusing on computations of complex three-dimensional flow fields about realistic aerodynamic bodies. To perform such computations, a very accurate and detailed description of the surface geometry must be provided, and a three-dimensional grid must be generated in the space around the body. The geometry must be supplied in a format compatible with the grid generation requirements, and must be verified to be free of inconsistencies. This paper presents a procedure for performing the geometry definition of a fighter aircraft that makes use of a commercial computer-aided design/computer-aided manufacturing system. Furthermore, visual representations of the geometry are generated using a computer graphics system for verification of the body definition. Finally, the three-dimensional grids for fighter-like aircraft are generated by means of an efficient new parabolic grid generation method. This method exhibits good control of grid quality.

Geometry definition and grid generation for a complete fighter aircraft

NASA Technical Reports Server (NTRS)

Edwards, Thomas A.

1986-01-01

Recent advances in computing power and numerical solution procedures have enabled computational fluid dynamicists to attempt increasingly difficult problems. In particular, efforts are focusing on computations of complex three-dimensional flow fields about realistic aerodynamic bodies. To perform such computations, a very accurate and detailed description of the surface geometry must be provided, and a three-dimensional grid must be generated in the space around the body. The geometry must be supplied in a format compatible with the grid generation requirements, and must be verified to be free of inconsistencies. A procedure for performing the geometry definition of a fighter aircraft that makes use of a commercial computer-aided design/computer-aided manufacturing system is presented. Furthermore, visual representations of the geometry are generated using a computer graphics system for verification of the body definition. Finally, the three-dimensional grids for fighter-like aircraft are generated by means of an efficient new parabolic grid generation method. This method exhibits good control of grid quality.

Aerodynamics Model for a Generic ASTOVL Lift-Fan Aircraft

DOT National Transportation Integrated Search

1995-04-01

This report describes the aerodynamics model used in a simulation model of : an advanced short takeoff and vertical landing lift-far fighter aircraft. The : simulation model was developed for use in piloted evaluations of transition and : hover fligh...

Fun!

ERIC Educational Resources Information Center

Horne, Thomas

1988-01-01

Describes four IBM compatible flight simulator software packages: (1) "Falcon," air to air combat in an F-16 fighter; (2) "Chuck Yeager's Advanced Flight Trainer," test flight 14 different aircraft; (3) "Jet," air to air combat; and (4) "Flight Simulator," a realistic PC flight simulator program. (MVL)

X-31 Unloading Returning from Paris Air Show

NASA Technical Reports Server (NTRS)

1995-01-01

After being flown in the Paris Air Show in June 1995, the X-31 Enhanced Fighter Maneuverability Technology Demonstrator Aircraft, based at the NASA Dryden Flight Research Center, Edwards Air Force Base, California, is off-loaded from an Air Force Reserve C-5 transport after the ferry flight back to Edwards. At the air show, the X-31 demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems to provide controlled flight at very high angles of attack. The X-31 Enhanced Fighter Maneuverability (EFM) demonstrator flew at the Ames- Dryden Flight Research Facility, Edwards, California (redesignated the Dryden Flight Research Center in 1994) from February 1992 until 1995 and before that at the Air Force's Plant 42 in Palmdale, California. The goal of the project was to provide design information for the next generation of highly maneuverable fighter aircraft. This program demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with an advanced flight control system to provide controlled flight to very high angles of attack. The result was a significant advantage over most conventional fighters in close-in combat situations. The X-31 flight program focused on agile flight within the post-stall regime, producing technical data to give aircraft designers a better understanding of aerodynamics, effectiveness of flight controls and thrust vectoring, and airflow phenomena at high angles of attack. Stall is a condition of an airplane or an airfoil in which lift decreases and drag increases due to the separation of airflow. Thrust vectoring compensates for the loss of control through normal aerodynamic surfaces that occurs during a stall. Post-stall refers to flying beyond the normal stall angle of attack, which in the X-31 was at a 30-degree angle of attack. During Dryden flight testing, the X-31 aircraft established several milestones. On November 6, 1992, the X-31 achieved controlled flight at a 70-degree angle of attack. On April 29, 1993, the second X-31 successfully executed a rapid minimum-radius, 180-degree turn using a post-stall maneuver, flying well beyond the aerodynamic limits of any conventional aircraft. This revolutionary maneuver has been called the 'Herbst Maneuver' after Wolfgang Herbst, a German proponent of using post-stall flight in air-to-air combat. It is also called a 'J Turn' when flown to an arbitrary heading change. The aircraft was flown in tactical maneuvers against an F/A-18 and other tactical aircraft as part of the test flight program. During November and December 1993, the X-31 reached a supersonic speed of Mach 1.28. In 1994, the X-31 program installed software to demonstrate quasi-tailless operation. The X-31 flight test program was conducted by an international test organization (ITO) managed by the Advanced Research Projects Office (ARPA), known as the Defense Advanced Research Projects Office (DARPA) before March 1993. The ITO included the U.S. Navy and U.S. Air Force, Rockwell Aerospace, the Federal Republic of Germany, Daimler-Benz (formerly Messerschmitt-Bolkow-Blohm and Deutsche Aerospace), and NASA. Gary Trippensee was the ITO director and NASA Project Manager. Pilots came from participating organizations. The X-31 was 43.33 feet long with a wingspan of 23.83 feet. It was powered by a single General Electric P404-GE-400 turbofan engine that produced 16,000 pounds of thrust in afterburner.

Certification Issues Relating to ABDR

DTIC Science & Technology

2010-05-01

design techniques, among them increased utilization of advanced fibre reinforced materials or advanced metal alloys with higher material allowables for...most cases as a combination of a high strength/modulus carbon fibre and a hot curing thermoset resin. A high percentage of modern fighter aircraft’s...34Limited Fibre Strain Approach" at ultimate design loadcases, where the reduced material allowables account for a low energy impact damage level

Study of aerodynamic technology for single-cruise engine V/STOL fighter/attack aircraft

NASA Technical Reports Server (NTRS)

Driggers, H. H.; Powers, S. A.; Roush, R. T.

1982-01-01

A conceptual design analysis is performed on a single engine V/STOL supersonic fighter/attack concept powered by a series flow tandem fan propulsion system. Forward and aft mounted fans have independent flow paths for V/STOL operation and series flow in high speed flight. Mission, combat and V/STOL performance is calculated. Detailed aerodynamic estimates are made and aerodynamic uncertainties associated with the configuration and estimation methods identified. A wind tunnel research program is developed to resolve principal uncertainties and establish a data base for the baseline configuration and parametric variations.

New rotation-balance apparatus for measuring airplane spin aerodynamics in the wind tunnel

NASA Technical Reports Server (NTRS)

Malcolm, G. N.

1978-01-01

An advanced rotation-balance apparatus has been developed for the Ames 12-ft pressure tunnel to study the effects of spin rate, angles of attack and sideslip, and, particularly, Reynolds number on the aerodynamics of fighter and general aviation aircraft in a steady spin. Angles of attack to 100 deg and angles of sideslip to 30 deg are possible with spin rates to 42 rad/sec (400 rpm) and Reynolds numbers to 30 million/m on fighter models with wing spans that are typically 0.7 m. A complete description of the new rotation-balance apparatus, the sting/balance/model assembly, and the operational capabilities is given.

Future Carrier-Based Tactical Aircraft Study

DOT National Transportation Integrated Search

1996-03-01

This report describes an aircraft database which was developed to identify technology trends for several classes of tactical naval aircraft, including subsonic attack, supersonic fighter, and supersonic multimission aircraft classes. This study used ...

Troubled Partnership. An Assessment of U.S.-Japan Collaboration on the FS-X Fighter,

DTIC Science & Technology

1995-01-01

Technology Transfer and Flowback 32 Commercial Spinoffs to Japan Exaggerated 33 Emphasis on Technology Flowback from Japan Was Political...take part in the development of the FS-X, and en- sure flowback of Japanese technology to the United States. In return, Japan paid $60 million to LFWC...involved flowback and access to Japanese technology. The government agreements stipulated that Japan would provide all technology applied to the FS-X

The QuEST for multi-sensor big data ISR situation understanding

NASA Astrophysics Data System (ADS)

Rogers, Steven; Culbertson, Jared; Oxley, Mark; Clouse, H. Scott; Abayowa, Bernard; Patrick, James; Blasch, Erik; Trumpfheller, John

2016-05-01

The challenges for providing war fighters with the best possible actionable information from diverse sensing modalities using advances in big-data and machine learning are addressed in this paper. We start by presenting intelligence, surveillance, and reconnaissance (ISR) related big-data challenges associated with the Third Offset Strategy. Current approaches to big-data are shown to be limited with respect to reasoning/understanding. We present a discussion of what meaning making and understanding require. We posit that for human-machine collaborative solutions to address the requirements for the strategy a new approach, Qualia Exploitation of Sensor Technology (QuEST), will be required. The requirements for developing a QuEST theory of knowledge are discussed and finally, an engineering approach for achieving situation understanding is presented.

Wind-tunnel investigation of the powered low-speed longitudinal aerodynamics of the Vectored-Engine-Over (VEO) wing fighter configuration

NASA Technical Reports Server (NTRS)

Paulson, J. W.; Whitten, P. D.; Stumpfl, S. C.

1982-01-01

A wind-tunnel investigation incorporating both static and wind-on testing was conducted in the Langley 4- by 7-Meter Tunnel to determine the effects of vectored thrust along with spanwise blowing on the low-speed aerodynamics of an advanced fighter configuration. Data were obtained over a large range of thrust coefficients corresponding to takeoff and landing thrust settings for many nozzle configurations. The complete set of static thrust data and the complete set of longitudinal aerodynamic data obtained in the investigation are presented. These data are intended for reference purposes and, therefore, are presented without analysis or comment. The analysis of the thrust-induced effects found in the investigation are not discussed.

Investigation into the impact of agility on conceptual fighter design

NASA Technical Reports Server (NTRS)

Engelbeck, R. M.

1995-01-01

The Agility Design Study was performed by the Boeing Defense and Space Group for the NASA Langley Research Center. The objective of the study was to assess the impact of agility requirements on new fighter configurations. Global trade issues investigated were the level of agility, the mission role of the aircraft (air-to-ground, multi-role, or air-to-air), and whether the customer is Air force, Navy, or joint service. Mission profiles and design objectives were supplied by NASA. An extensive technology assessment was conducted to establish the available technologies to industry for the aircraft. Conceptual level methodology is presented to assess the five NASA-supplied agility metrics. Twelve configurations were developed to address the global trade issues. Three-view drawings, inboard profiles, and performance estimates were made and are included in the report. A critical assessment and lessons learned from the study are also presented.

A Nonlinear Three-Dimensional Micromechanics Model for Fiber-Reinforced Laminated Composites

DTIC Science & Technology

1993-11-01

Interfacial Properties Employed for the SCS6/Ti-15-3 Composite ......................... 150 11. Constants Employed for the LLFM Predictions of Quasi...Region m Matrix Property or Mean of the Interfacial Stress Distribution ml, m2, m3 Signifies Matrix Region n Normal to Interface r Signifies Equation...usage of the new class of titanium based com- posites in advanced aerospace structures and engines such as are targeted for the advanced tactical fighter

Technology utilization program report

NASA Technical Reports Server (NTRS)

1974-01-01

The application of aerospace technology to the solution of public health and industrial problems is reported. Data cover: (1) development of an externally rechargeable cardiac pacemaker, (2) utilization of ferrofluids-colloidal suspensions of ferrite particles - in the efficient separation of nonferrous metals as Ni, Zn, Cu, and Al from shredded automobile scrap, and (3) development of a breathing system for fire fighters.

Fiscal Year 2012 United States Air Force Agency Financial Report

DTIC Science & Technology

2012-01-01

Air Force Research Laboratory (AFRL) and Lawrence Livermore National Laboratory (LLNL) aggressively designed and tested an advanced warhead to...Reaper procurement & RPA capabilities, Light Attack Armed Reconnaissance buys, Joint Strike Fighter, satellites). Research , Development, Test and...Military Personnel Operations, Readiness & Support Procurement Research , Development, Test & Evaluation

The development of an airborne instrumentation computer system for flight test

NASA Technical Reports Server (NTRS)

Bever, G. A.

1984-01-01

Instrumentation interfacing frequently requires the linking of intelligent systems together, as well as requiring the link itself to be intelligent. The airborne instrumentation computer system (AICS) was developed to address this requirement. Its small size, approximately 254 by 133 by 140 mm (10 by 51/4 by 51/2 in), standard bus, and modular board configuration give it the ability to solve instrumentation interfacing and computation problems without forcing a redesign of the entire unit. This system has been used on the F-15 aircraft digital electronic engine control (DEEC) and its follow on engine model derivative (EMD) project and in an OV-1C Mohawk aircraft stall speed warning system. The AICS is presently undergoing configuration for use on an F-104 pace aircraft and on the advanced fighter technology integration (AFTI) F-111 aircraft.

The Dilemmas of Developing an Indigenous Advanced Arms Industry for Developing Countries: The Case of India and China

DTIC Science & Technology

2006-12-01

of providing nuclear power. Once you have the nuclear weapons, they require a delivery system resulting in a missile program. It is afforded higher...out that some domestic advancements may be made in certain sectors, such as nuclear bombs and missiles, because resources may be spent on narrowly...capital, fighter, aviation, nuclear weapons, missiles 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT Unclassified 18. SECURITY CLASSIFICATION

Advanced Video Data-Acquisition System For Flight Research

NASA Technical Reports Server (NTRS)

Miller, Geoffrey; Richwine, David M.; Hass, Neal E.

1996-01-01

Advanced video data-acquisition system (AVDAS) developed to satisfy variety of requirements for in-flight video documentation. Requirements range from providing images for visualization of airflows around fighter airplanes at high angles of attack to obtaining safety-of-flight documentation. F/A-18 AVDAS takes advantage of very capable systems like NITE Hawk forward-looking infrared (FLIR) pod and recent video developments like miniature charge-couple-device (CCD) color video cameras and other flight-qualified video hardware.

JPRS Report Science & Technology Europe.

DTIC Science & Technology

1992-10-22

Potatoes for More Sugar [Frankfurt/Main FRANKFURTER ALLEGEMEINE, 12 Aug 92] 26 COMPUTERS French Devise Operating System for Parallel, Failure...Tolerant and Real-Time Systems [Munich COMPUTER WOCHE, 5 Jun 92] 27 Germany Markets External Mass Memory for IBM-Compatible Parallel Interfaces...Infrared Detection System [Thierry Lucas; Paris L’USINE NOUVELLE TECHNOLOGIES, 16 Jul 92] 28 Streamlined ACE Fighter Airplane Approved [Paris AFP

Study of aerodynamic technology for VSTOL fighter/attack aircraft, phase 1

NASA Technical Reports Server (NTRS)

Driggers, H. H.

1978-01-01

A conceptual design study was performed of a vertical attitude takeoff and landing (VATOL) fighter/attack aircraft. The configuration has a close-coupled canard-delta wing, side two-dimensional ramp inlets, and two augmented turbofan engines with thrust vectoring capability. Performance and sensitivities to objective requirements were calculated. Aerodynamic characteristics were estimated based on contractor and NASA wind tunnel data. Computer simulations of VATOL transitions were performed. Successful transitions can be made, even with series post-stall instabilities, if reaction controls are properly phased. Principal aerodynamic uncertainties identified were post-stall aerodynamics, transonic aerodynamics with thrust vectoring and inlet performance in VATOL transition. A wind tunnel research program was recommended to resolve the aerodynamic uncertainties.

Study of aerodynamic technology for single-cruise-engine V/STOL fighter/attack aircraft

NASA Technical Reports Server (NTRS)

Mark, L.

1982-01-01

Conceptual designs and analyses were conducted on two V/STOL supersonic fighter/attack aircraft. These aircraft feature low footprint temperature and pressure thrust augmenting ejectors in the wings for vertical lift, combined with a low wing loading, low wave drag airframe for outstanding cruise and supersonic performance. Aerodynamic, propulsion, performance, and mass properties were determined and are presented for each aircraft. Aerodynamic and Aero/Propulsion characteristics having the most significant effect on the success of the up and away flight mode were identified, and the certainty with which they could be predicted was defined. A wind tunnel model and test program are recommended to resolve the identified uncertainties.

Structural design optimization with survivability dependent constraints application: Primary wing box of a multi-role fighter

NASA Technical Reports Server (NTRS)

Dolvin, Douglas J.

1992-01-01

The superior survivability of a multirole fighter is dependent upon balanced integration of technologies for reduced vulnerability and susceptability. The objective is to develop a methodology for structural design optimization with survivability dependent constraints. The design criteria for optimization will be survivability in a tactical laser environment. The following analyses are studied to establish a dependent design relationship between structural weight and survivability: (1) develop a physically linked global design model of survivability variables; and (2) apply conventional constraints to quantify survivability dependent design. It was not possible to develop an exact approach which would include all aspects of survivability dependent design, therefore guidelines are offered for solving similar problems.

Fatigue Fighters in Sjogren's Syndrome

MedlinePlus

... few hours to help you get through your day. Educate your friends and family about what you are going through and how ... to help you with tasks. Ask friends and family members to be prepared to do one or two chores for you on your fatigue days. Give them specific instructions in advance and be ...

Advanced simulation noise model for modern fighter aircraft

NASA Astrophysics Data System (ADS)

Ikelheimer, Bruce

2005-09-01

NoiseMap currently represents the state of the art for military airfield noise analysis. While this model is sufficient for the current fleet of aircraft, it has limits in its capability to model the new generation of fighter aircraft like the JSF and the F-22. These aircraft's high-powered engines produce noise with significant nonlinear content. Combining this with their ability to vector the thrust means they have noise characteristics that are outside of the basic modeling assumptions of the currently available noise models. Wyle Laboratories, Penn State University, and University of Alabama are in the process of developing a new noise propagation model for the Strategic Environmental Research and Development Program. Source characterization will be through complete spheres (or hemispheres if there is not sufficient data) for each aircraft state (including thrust vector angles). Fixed and rotor wing aircraft will be included. Broadband, narrowband, and pure tone propagation will be included. The model will account for complex terrain and weather effects, as well as the effects of nonlinear propagation. It will be a complete model capable of handling a range of noise sources from small subsonic general aviation aircraft to the latest fighter aircraft like the JSF.

Some Aviation Growth Events

NASA Technical Reports Server (NTRS)

Spearman, M. Leroy

2002-01-01

The growth of aviation since the first flight of a heavier-than-air powered manned vehicle in 1903 has been somewhat remarkable. Some of the events that have influenced this growth are reviewed in this paper. This review will include some events prior to World War I; the influence of the war itself; the events during the post-war years including the establishment of aeronautical research laboratories; and the influence of World War II which, among other things, introduced new technologies that included rocket and jet propulsion and supersonic aerodynamics. The subsequent era of aeronautical research and the attendant growth in aviation over the past half century will be reviewed from the view point of the author who, since 1944, has been involved in the NACA/NASA aeronautical research effort at what is now the Langley Research Center in Hampton, Virginia. The review will discuss some of the research programs related to the development of some experimental aircraft, the Century series of fighter aircraft, multi-mission aircraft, advanced military aircraft and missiles, advanced civil aircraft, supersonic transports, spacecraft and others.

X-36 Tailless Fighter Agility Research Aircraft in flight

NASA Image and Video Library

1997-10-30

The lack of a vertical tail on the X-36 technology demonstrator is evident as the remotely piloted aircraft flies a low-altitude research flight above Rogers Dry Lake at Edwards Air Force Base in the California desert on October 30, 1997.

A knowledge-based system design/information tool for aircraft flight control systems

NASA Technical Reports Server (NTRS)

Mackall, Dale A.; Allen, James G.

1991-01-01

Research aircraft have become increasingly dependent on advanced electronic control systems to accomplish program goals. These aircraft are integrating multiple disciplines to improve performance and satisfy research objective. This integration is being accomplished through electronic control systems. Systems design methods and information management have become essential to program success. The primary objective of the system design/information tool for aircraft flight control is to help transfer flight control system design knowledge to the flight test community. By providing all of the design information and covering multiple disciplines in a structured, graphical manner, flight control systems can more easily be understood by the test engineers. This will provide the engineers with the information needed to thoroughly ground test the system and thereby reduce the likelihood of serious design errors surfacing in flight. The secondary object is to apply structured design techniques to all of the design domains. By using the techniques in the top level system design down through the detailed hardware and software designs, it is hoped that fewer design anomalies will result. The flight test experiences are reviewed of three highly complex, integrated aircraft programs: the X-29 forward swept wing; the advanced fighter technology integration (AFTI) F-16; and the highly maneuverable aircraft technology (HiMAT) program. Significant operating technologies, and the design errors which cause them, is examined to help identify what functions a system design/informatin tool should provide to assist designers in avoiding errors.

Laser Shot Peening Final Report CRADA No. TC-02059-03

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stuart, B. C.; Hackel, L.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Metal Improvement Company, Inc. (MIC), to further develop the laser shot peening technology. This project had an emphasis on laser development and government and military applications including DOE’s natural gas and oil technology program (NGOTP), Yucca Mountain Project (YMP), F-22 Fighter, etc.

Near-maximal ECG stress testing and coronary artery disease risk factor analysis in Los Angeles City fire fighters.

PubMed

Barnard, R J; Gardner, G W; Diaco, N V; Kattus, A A

1975-11-01

Near-maximal ECG stress testing and coronary artery disease risk factor analysis including blood pressure, serum cholesterol and smoking habits were conducted on a randomly selected group (N=90) of Los Angeles City Fire Fighters ranging in age from 40 to 59 yrs. The data obtained from the fire fighters were compared to data previously reported for a group of Los Angeles insurance underwriters of the same age range. Only 12% of the fire fighters had cholesterol values greater than 260 mg% while 18% of the insurance executives fell into this category. Only 2% of the fire fighters had blood pressure values greater than 160/90 mm Hg while 25% of the insurance executives were hypertensive. Thirty-two percent of the fire fighters were smokers at the time of testing as compared to 26% for the insurance executives. Only one fire fighter had all three risk factors elevated and only five had two risk factors elevated. Forty-seven of the fire fighters had no risk factors elevated. Ten percent of the fire fighters had ischemic stress tests as compared to 8% for the insurance executives. Of the nine fire fighters with ischemic stress tests one was hypertensive, one had elevated serum triglycerides, and three were smokers at the time of testing. Since the fire fighters are a medically-selected population with low risk factors for CHD, the observed incidence of ischemic stress tests is surprising and suggests that ischemic heart disease may be job associated.

Fiber-Optic Sensor And Smart Structures Research At Florida Institute Of Technology

NASA Astrophysics Data System (ADS)

Grossman, Barry G.; Alavie, A. Tino; Ham, Fredric M.; Franke, Jorge E.; Thursby, Michael H.

1990-02-01

This paper discusses the fundamental issues being investigated by Florida Institute of Technology (F.I.T.) to implement the technology of smart structural systems for DoD, NASA, and commercial applications. Embedded sensors and actuators controlled by processors can provide a modification of the mechanical characteristics of composite structures to produce smart structures1-3. Recent advances in material science have spurred the development and use of composite materials in a wide range of applications from rotocraft blades and advanced tactical fighter aircraft to undersea and aerospace structures. Along with the advantages of an increased strength-to-weight ratio, the use of these materials has raised a number of questions related to understanding their failure mechanisms. Also, being able to predict structural failures far enough in advance to prevent them and to provide real-time structural health and damage monitoring has become a realistic possibility. Unfortunately, conventional sensors, actuators, and digital processors, although highly developed and well proven for other systems, may not be best suited for most smart structure applications. Our research has concentrated on few-mode and polarimetric single-fiber strain sensors4-7 and optically activated shape memory alloy (SMA) actuators controlled by artificial neural processors. We have constructed and characterized both few-mode and polarimetric sensors for a variety of fiber types, including standard single-mode, high-birefringence polarization preserving, and low-birefringence polarization insensitive fibers. We have investigated signal processing techniques for these sensors and have demonstrated active phase tracking for the high- and low-birefringence polarimetric sensors through the incorporation into the system of an electrooptic modulator designed and fabricated at F.I.T.. We have also started the design and testing of neural network architectures for processing the sensor signal outputs to calculate strain magnitude and actuator control signals for simple structures.

X-31 Loaded in C-5 Cargo Bay

NASA Technical Reports Server (NTRS)

1995-01-01

The X-31 Enhanced Fighter Maneuverability Technology Demonstrator Aircraft, based at the NASA Dryden Flight Research Center, Edwards Air Force Base, California, is secured inside the fuselage of an Air Force Reserve C-5 transport. The C-5 was used to ferry the X-31 from Europe back to Edwards, after being flown in the Paris Air Show in June 1995. The X-31's right wing, removed so the aircraft could fit inside the C-5, is in the shipping container in the foreground. At the air show, the X-31 demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems to provide controlled flight at very high angles of attack. The X-31 Enhanced Fighter Maneuverability (EFM) demonstrator flew at the Ames- Dryden Flight Research Facility, Edwards, California (redesignated the Dryden Flight Research Center in 1994) from February 1992 until 1995 and before that at the Air Force's Plant 42 in Palmdale, California. The goal of the project was to provide design information for the next generation of highly maneuverable fighter aircraft. This program demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with an advanced flight control system to provide controlled flight to very high angles of attack. The result was a significant advantage over most conventional fighters in close-in combat situations. The X-31 flight program focused on agile flight within the post-stall regime, producing technical data to give aircraft designers a better understanding of aerodynamics, effectiveness of flight controls and thrust vectoring, and airflow phenomena at high angles of attack. Stall is a condition of an airplane or an airfoil in which lift decreases and drag increases due to the separation of airflow. Thrust vectoring compensates for the loss of control through normal aerodynamic surfaces that occurs during a stall. Post-stall refers to flying beyond the normal stall angle of attack, which in the X-31 was at a 30-degree angle of attack. During Dryden flight testing, the X-31 aircraft established several milestones. On November 6, 1992, the X-31 achieved controlled flight at a 70-degree angle of attack. On April 29, 1993, the second X-31 successfully executed a rapid minimum-radius, 180-degree turn using a post-stall maneuver, flying well beyond the aerodynamic limits of any conventional aircraft. This revolutionary maneuver has been called the 'Herbst Maneuver' after Wolfgang Herbst, a German proponent of using post-stall flight in air-to-air combat. It is also called a 'J Turn' when flown to an arbitrary heading change. The aircraft was flown in tactical maneuvers against an F/A-18 and other tactical aircraft as part of the test flight program. During November and December 1993, the X-31 reached a supersonic speed of Mach 1.28. In 1994, the X-31 program installed software to demonstrate quasi-tailless operation. The X-31 flight test program was conducted by an international test organization (ITO) managed by the Advanced Research Projects Office (ARPA), known as the Defense Advanced Research Projects Office (DARPA) before March 1993. The ITO included the U.S. Navy and U.S. Air Force, Rockwell Aerospace, the Federal Republic of Germany, Daimler-Benz (formerly Messerschmitt-Bolkow-Blohm and Deutsche Aerospace), and NASA. Gary Trippensee was the ITO director and NASA Project Manager. Pilots came from participating organizations. The X-31 was 43.33 feet long with a wingspan of 23.83 feet. It was powered by a single General Electric P404-GE-400 turbofan engine that produced 16,000 pounds of thrust in afterburner.

Stability Result For Dynamic Inversion Devised to Control Large Flexible Aircraft

NASA Technical Reports Server (NTRS)

Gregory, Irene M.

2001-01-01

High performance aircraft of the future will be designed lighter, more maneuverable, and operate over an ever expanding flight envelope. One of the largest differences from the flight control perspective between current and future advanced aircraft is elasticity. Over the last decade, dynamic inversion methodology has gained considerable popularity in application to highly maneuverable fighter aircraft, which were treated as rigid vehicles. This paper is an initial attempt to establish global stability results for dynamic inversion methodology as applied to a large, flexible aircraft. This work builds on a previous result for rigid fighter aircraft and adds a new level of complexity that is the flexible aircraft dynamics, which cannot be ignored even in the most basic flight control. The results arise from observations of the control laws designed for a new generation of the High-Speed Civil Transport aircraft.

Structured analysis and modeling of complex systems

NASA Technical Reports Server (NTRS)

Strome, David R.; Dalrymple, Mathieu A.

1992-01-01

The Aircrew Evaluation Sustained Operations Performance (AESOP) facility at Brooks AFB, Texas, combines the realism of an operational environment with the control of a research laboratory. In recent studies we collected extensive data from the Airborne Warning and Control Systems (AWACS) Weapons Directors subjected to high and low workload Defensive Counter Air Scenarios. A critical and complex task in this environment involves committing a friendly fighter against a hostile fighter. Structured Analysis and Design techniques and computer modeling systems were applied to this task as tools for analyzing subject performance and workload. This technology is being transferred to the Man-Systems Division of NASA Johnson Space Center for application to complex mission related tasks, such as manipulating the Shuttle grappler arm.

Calculated performance, stability and maneuverability of high-speed tilting-prop-rotor aircraft

NASA Technical Reports Server (NTRS)

Johnson, Wayne; Lau, Benton H.; Bowles, Jeffrey V.

1986-01-01

The feasibility of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advance technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA)

NASA Technical Reports Server (NTRS)

Palumbo, Daniel L.; Cohen, Gerald C.; Meissner, Charles W.

1990-01-01

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA) is a two-phase program which was initiated by NASA in the early 80s. The first phase, IAPSA 1, studied different architectural approaches to the problem of integrating engine control systems with airframe control systems in an advanced tactical fighter. One of the conclusions of IAPSA 1 was that the technology to construct a suitable system was available, yet the ability to create these complex computer architectures has outpaced the ability to analyze the resulting system's performance. With this in mind, the second phase of IAPSA approached the same problem with the added constraint that the system be designed for validation. The intent of the design for validation requirement is that validation requirements should be shown to be achievable early in the design process. IAPSA 2 has demonstrated that despite diligent efforts, integrated systems can retain characteristics which are difficult to model and, therefore, difficult to validate.

Aircraft Electric Secondary Power

NASA Technical Reports Server (NTRS)

1983-01-01

Technologies resulted to aircraft power systems and aircraft in which all secondary power is supplied electrically are discussed. A high-voltage dc power generating system for fighter aircraft, permanent magnet motors and generators for aircraft, lightweight transformers, and the installation of electric generators on turbine engines are among the topics discussed.

Observations on the Air War in Syria

DTIC Science & Technology

2013-04-01

comfortable with a trainer aircraft. In January 2012, the Syrian air force attempted to buy 40 Yak -130 trainers from Russia, but in July 2012...election-result-delay-coup-live. 32. “Russia Will Not Deliver Yak -130 Fighter Jets to Syria,” Airforce-technology.com, 9 July 2012, http://www.airforce

Application of an Adaptive Clustering Network to Flight Control of a Fighter Aircraft. Phase 1

DTIC Science & Technology

1991-12-19

whether the underlying neurodynamics are appropriate to the dynamics of the controlled element as well as the broad objectives of the control process...Dept. of Brain & Cognitive Sciences ........................ 1 Massachusetts Institute of Technology Cambridge, MA 02139 Attn: Dr. M. Jordan Dept. of

Reduction of structural loads using maneuver load control on the Advanced Fighter Technology Integration (AFTI)/F-111 mission adaptive wing

NASA Technical Reports Server (NTRS)

Thornton, Stephen V.

1993-01-01

A transonic fighter-bomber aircraft, having a swept supercritical wing with smooth variable-camber flaps was fitted with a maneuver load control (MLC) system that implements a technique to reduce the inboard bending moments in the wing by shifting the spanwise load distribution inboard as load factor increases. The technique modifies the spanwise camber distribution by automatically commanding flap position as a function of flap position, true airspeed, Mach number, dynamic pressure, normal acceleration, and wing sweep position. Flight test structural loads data were obtained for loads in both the wing box and the wing root. Data from uniformly deflected flaps were compared with data from flaps in the MLC configuration where the outboard segment of three flap segments was deflected downward less than the two inboard segments. The changes in the shear loads in the forward wing spar and at the roots of the stabilators also are presented. The camber control system automatically reconfigures the flaps through varied flight conditions. Configurations having both moderate and full trailing-edge flap deflection were tested. Flight test data were collected at Mach numbers of 0.6, 0.7, 0.8, and 0.9 and dynamic pressures of 300, 450, 600, and 800 lb/sq ft. The Reynolds numbers for these flight conditions ranged from 26 x 10(exp 6) to 54 x 10(exp 6) at the mean aerodynamic chord. Load factor increases of up to 1.0 g achieved with no increase in wing root bending moment with the MLC flap configuration.

Low-speed wind-tunnel investigation of a porous forebody and nose strakes for yaw control of a multirole fighter aircraft

NASA Technical Reports Server (NTRS)

Fears, Scott P.

1995-01-01

Low-speed wind-tunnel tests were conducted in the Langley 12-Foot Low-Speed Tunnel on a model of the Boeing Multirole Fighter (BMRF) aircraft. This single-seat, single-engine configuration was intended to be an F-16 replacement that would incorporate many of the design goals and advanced technologies of the F-22. Its mission requirements included supersonic cruise without afterburner, reduced observability, and the ability to attack both air-to-air and air-to-ground targets. So that it would be effective in all phases of air combat, the ability to maneuver at angles of attack up to and beyond maximum lift was also desired. Traditional aerodynamic yaw controls, such as rudders, are typically ineffective at these higher angles of attack because they are usually located in the wake from the wings and fuselage. For this reason, this study focused on investigating forebody-mounted controls that produces yawing moments by modifying the strong vortex flowfield being shed from the forebody at high angles of attack. Two forebody strakes were tested that varied in planform and chordwise location. Various patterns of porosity in the forebody skin were also tested that differed in their radial coverage and chordwise location. The tests were performed at a dynamic pressure of 4 lb/ft(exp 2) over an angle-of-attack range of -4 deg to 72 deg and a sideslip range of -10 deg to 10 deg. Static force data, static pressures on the surface of the forebody, and videotapes of flow-visualization using laser-illuminated smoke were obtained.

Scandinavian neuroscience during the Nazi era.

PubMed

Kondziella, Daniel; Hansen, Klaus; Zeidman, Lawrence A

2013-07-01

Although Scandinavian neuroscience has a proud history, its status during the Nazi era has been overlooked. In fact, prominent neuroscientists in German-occupied Denmark and Norway, as well as in neutral Sweden, were directly affected. Mogens Fog, Poul Thygesen (Denmark) and Haakon Sæthre (Norway) were resistance fighters, tortured by the Gestapo: Thygesen was imprisoned in concentration camps and Sæthre executed. Jan Jansen (Norway), another neuroscientist resistor, escaped to Sweden, returning under disguise to continue fighting. Fritz Buchthal (Denmark) was one of almost 8000 Jews escaping deportation by fleeing from Copenhagen to Sweden. In contrast, Carl Værnet (Denmark) became a collaborator, conducting inhuman experiments in Buchenwald concentration camp, and Herman Lundborg (Sweden) and Thorleif Østrem (Norway) advanced racial hygiene in order to maintain the "superior genetic pool of the Nordic race." Compared to other Nazi-occupied countries, there was a high ratio of resistance fighters to collaborators and victims among the neuroscientists in Scandinavia.

Low-speed investigation of effects of wing leading- and trailing-edge flap deflections and canard incidence on a fighter configuration equipped with a forward-swept wing

NASA Technical Reports Server (NTRS)

Gainer, T. G.; Mann, M. J.; Huffman, J. K.

1984-01-01

An advanced fighter configuration with a forward-swept wing of aspect ratio 3.28 is tested in the Langley 7 by 10 Foot High Speed Tunnel at a Mach number of 0.3. The wing has 29.5 degrees of forward sweep of the quarter chord line and is equipped with 15 percent chord leading edge and 30 percent chord trailing edge flaps. The canard is sweptback 45 degrees. Tests were made through a range of angle of attack from about -2 degrees to 22 degrees. Deflecting the flaps significantly improves the lift drag characteristics at the higher angles of attack. The canard is able to trim the configurations with different flap deflections over most of the range of angle of attack. The penalty in maximum lift coefficient due to trimming is about 0.10.

LDV Surveys Over a Fighter Model at Moderate to High Angles of Attack

NASA Technical Reports Server (NTRS)

Sellers, William L., III; Meyers, James F.; Hepner, Timothy E.

2004-01-01

The vortex flowfield over an advanced twin-tailed fighter configuration was measured in a low-speed wind tunnel at two angles of attack. The primary test data consisted of 3-component velocity surveys obtained using a Laser Doppler Velocimeter. Laser light sheet and surface flow visualization were also obtained to provide insight into the flowfield structure. Time-averaged velocities and the root mean square of the velocity fluctuations were obtained at two cross-sections above the model. At 15 degrees angle of attack, the vortices generated by the wing leading edge extension (LEX) were unburst over the model and passed outboard of the vertical tail. At 25 degrees angle of attack, the vortices burst in the vicinity of the wing-LEX intersection and impact directly on the vertical tails. The RMS levels of the velocity fluctuations reach values of approximately 30% in the region of the vertical tails.

Fire fighter fatalities 1998–2001: overview with an emphasis on structure related traumatic fatalities

PubMed Central

Hodous, T; Pizatella, T; Braddee, R; Castillo, D

2004-01-01

Objective: To review the causes of all fire fighter line-of-duty-deaths from 1998 through 2001, and present recommendations for preventing fatalities within the specific subgroup of structure related events. Methods: Fire fighter fatality data from the United States Fire Administration were reviewed and classified into three main categories of injury. Investigations conducted through the National Institute for Occupational Safety and Health (NIOSH) Fire Fighter Fatality Investigation and Prevention Program provided the basis for the recommendations presented in this paper. Results: During the time period from 1998–2001, there were 410 line-of-duty deaths among fire fighters in the United States, excluding the 343 fire fighters who died at the World Trade Center on 11 September 2001. The 410 fatalities included 191 medical (non-traumatic) deaths (47%), 75 motor vehicle related fatalities (18%), and 144 other traumatic fatalities (35%). The latter group included 68 fatalities that were associated with structures which commonly involved structural collapse, rapid fire progression, and trapped fire fighters. Conclusions: Structural fires pose particular hazards to fire fighters. Additional efforts must be directed to more effectively use what we have learned through the NIOSH investigations and recommendations from published experts in the safety community, consensus standards, and national fire safety organizations to reduce fire fighter fatalities during structural fire fighting. PMID:15314049

Chinese Arms Production and Sales for the Third World

DTIC Science & Technology

1991-01-01

Egypt J-6 fighter 60 Guinea Shanghai-class patrol boat 4 Kampuchea (Khmer Rouge) Type-59 MBT NA HJ-73 ATGW 200+ J-5 fighter 4 J-6 fighter 16 North Korea...Shanghai-class patrol boat 6 Tunisia Shanghai-class patrol boat 2 Zaire T-62 light tank 50 Type-56/-59/- 60 /-63 arty 80 Huanchen-class FAC(T) 4 Zambia T-59...fighter 75+ J-7 fighter 60 Chaho-class patrol boat 3 HY-2/FL-1 antishipping missile 72+ C-801 antishipping missile 100 Iraq Type-59 MBT 1000 Type-69 MBT

Which subgroups of fire fighters are more prone to work-related diminished health requirements?

PubMed

Plat, Marie-Christine J; Frings-Dresen, Monique H W; Sluiter, Judith K

2012-10-01

To determine whether certain subgroups of fire fighters are prone to work-related diminished health requirements. The health requirements for fire-fighting were tested in a workers' health surveillance (WHS) setting. These health requirements included psychological, physical and sense-related components as well as cardiovascular risk factors. The odds ratio (OR) and 95% confidence interval (95% CI) for the presence of the diminished health requirements were calculated for the subgroups of gender, professionalism and age. The prevalence of diminished psychological requirements was equivalent among the subgroups, and no significant high-risk group was identified. As compared to men fire fighters, women fire fighters were more likely to have diminished physical requirements (OR 28.5; 95% CI 12.1-66.9) and less likely to have cardiovascular risk factors (OR 0.3; 0.1-0.5). As compared to volunteer fire fighters, professionals were less likely to have diminished physical requirements (OR 0.5; 0.3-0.9), but professionals had a higher prevalence of cardiovascular risk factors with an odds ratio of 1.9 (1.1-3.2). As compared to the youngest fire fighters, the oldest fire fighters were more likely to have diminished sense-related requirements (OR 7.1; 3.4-15.2); a similar comparison could be made between oldest and middle-aged fire fighters (OR 5.1; 2.5-10.5). In addition, the oldest fire fighters were more likely to have cardiovascular risk factors when compared to the youngest (OR 4.4; 1.7-11.1) and to the middle-aged fire fighters (OR 3.1; 1.2-7.9). Subgroups (gender, professionalism and age) of fire fighters are prone to at least one specific work-related diminished health requirement. Therefore, parts of the WHS could be applied with more attention to these high-risk groups.

Dehydration and acute weight gain in mixed martial arts fighters before competition.

PubMed

Jetton, Adam M; Lawrence, Marcus M; Meucci, Marco; Haines, Tracie L; Collier, Scott R; Morris, David M; Utter, Alan C

2013-05-01

The purpose of this study was to characterize the magnitude of acute weight gain (AWG) and dehydration in mixed martial arts (MMA) fighters before competition. Urinary measures of hydration status and body mass were determined approximately 24 hours before and then again approximately 2 hours before competition in 40 MMA fighters (mean ± SE, age: 25.2 ± 0.65 years, height: 1.77 ± 0.01 m, body mass: 75.8 ± 1.5 kg). The AWG was defined as the amount of body weight the fighters gained in the approximately 22-hour period between the official weigh-in and the actual competition. On average, the MMA fighters gained 3.40 ± 2.2 kg or 4.4% of their body weight in the approximately 22-hour period before competition. Urine specific gravity significantly decreased (p < 0.001) from 1.028 ± 0.001 to 1.020 ± 0.001 during the approximately 22-hour rehydration period. Results demonstrated that 39% of the MMA fighters presented with a Usg of >1.021 immediately before competition indicating significant or serious dehydration. The MMA fighters undergo significant dehydration and fluctuations in body mass (4.4% avg.) in the 24-hour period before competition. Urinary measures of hydration status indicate that a significant proportion of MMA fighters are not successfully rehydrating before competition and subsequently are competing in a dehydrated state. Weight management guidelines to prevent acute dehydration in MMA fighters are warranted to prevent unnecessary adverse health events secondary to dehydration.

Hearings Before the Committee on Aeronautical and Space Sciences. United States Senate, Ninety-Third Congress, Second Session

DTIC Science & Technology

1974-07-18

concepts which, when de - veloped, will provide for the combination of new structural design concepts with the new developments in airframe fabri- cation...19-20 9. Cargo aircraft design for special applications ------ 20 10. Advanced fighter concepts------------------------ 21 11-12. Hypersonic...Research, De - velopment and Engineering. U.S. Army Aviation Systems Command -------------------------------------------- 172 Appendix: Statement on behalf

Test Bus Evaluation

DTIC Science & Technology

1998-04-01

selected is statistically based on the total number of faults and the failure rate distribution in the system under test. The fault set is also...implemented the BPM and system level emulation consolidation logic as well as statistics counters for cache misses and various bus transactions. These...instruction F22 Advanced Tactical Fighter FET Field Effect Transitor FF Flip-Flop FM Failures/Milhon hours C-3 FPGA Field Programmable Gate Array GET

Summary of 1989 - 1990 aeronautics design projects

NASA Technical Reports Server (NTRS)

1990-01-01

Four design projects were completed at Auburn University this year under the sponsorship of the NASA/Universities Space Research Association Advanced Design Program. The topics discussed are the design of a high speed civil transport; the design of a 79 passenger, high efficiency, commercial transport; the design of a low cost short takeof vertical landing export fighter; and the design of an ozone monitoring vehicle.

HARV ANSER Flight Test Data Retrieval and Processing Procedures

NASA Technical Reports Server (NTRS)

Yeager, Jessie C.

1997-01-01

Under the NASA High-Alpha Technology Program the High Alpha Research Vehicle (HARV) was used to conduct flight tests of advanced control effectors, advanced control laws, and high-alpha design guidelines for future super-maneuverable fighters. The High-Alpha Research Vehicle is a pre-production F/A-18 airplane modified with a multi-axis thrust-vectoring system for augmented pitch and yaw control power and Actuated Nose Strakes for Enhanced Rolling (ANSER) to augment body-axis yaw control power. Flight testing at the Dryden Flight Research Center (DFRC) began in July 1995 and continued until May 1996. Flight data will be utilized to evaluate control law performance and aircraft dynamics, determine aircraft control and stability derivatives using parameter identification techniques, and validate design guidelines. To accomplish these purposes, essential flight data parameters were retrieved from the DFRC data system and stored on the Dynamics and Control Branch (DCB) computer complex at Langley. This report describes the multi-step task used to retrieve and process this data and documents the results of these tasks. Documentation includes software listings, flight information, maneuver information, time intervals for which data were retrieved, lists of data parameters and definitions, and example data plots.

Behind the Power Curve: The Regular Air Force Pilots Shortages Effect on Air National Guard Fighter Squadrons

DTIC Science & Technology

2016-04-01

in 2017. Recall from the previous retention section that there is nearly a 50% drop in the total AC fighter pilot inventory available to separate...8 Figure 3. Total Fighter Pilots by Year Group ...................................................................11 Figure 4...important for the Total Force to find an equitable balance and refine the forcing functions to produce, absorb, and sustain the dwindling fighter

Handling qualities related to stall/spin accidents of supersonic fighter aircraft

NASA Technical Reports Server (NTRS)

Anderson, S. B.

1984-01-01

This paper reviews the handling qualities which influence the high angle of attack (AOA) behavior of supersonic fighter aircraft in order to obtain a clearer understanding of the causes of stall/spin accidents. The results show that, because modern fighters suffer more serious consequences when control is lost, good handling qualities are essential for safe operation at high AOA. Relaxed static stability used on some fighter aircraft can result in control problems at high AOA owing to inertia coupling and the difficulty of a recovery from a deep stall. Indications are that the use of departure/spin resistance and an automatic spin prevention system will greatly improve the safety record for modern supersonic fighters.

AFTI/F-16

NASA Technical Reports Server (NTRS)

1991-01-01

The AFTI F-16 flying at high angle of attack, shown in the final configuration and paint finish. Dummy Sidewinder air-to-air missles are attached to the wing tips. The white objects visible on the wing racks represent practice bomb dispensers, used in weapon tests. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

AFTI/F-16 50th flight team photo

NASA Technical Reports Server (NTRS)

1983-01-01

An early (1983) photograph of the AFTI F-16 team, commemorating the aircraft's 50th flight. It shows the initial configuration and paint finish of the AFTI F-16, as well as the forward mounted canards and the spin chute. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

AFTI/F-16 in banked flight

NASA Technical Reports Server (NTRS)

1989-01-01

This photo depicts the AFTI F-16 in the configuration used midway through the program. The sensor pods were added to the fuselage, but the chin canards remained in place. Painted in non-standard gray tones, it carried Sidewinder air-to-air missles on its wingtips. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

AFTI/F-16

NASA Technical Reports Server (NTRS)

1992-01-01

The AFTI F-16 in its final configuration, flying in the vicinity of Edwards Air Force Base, California. During this phase, the two forward infrared turrets were added ahead of the cockpit, the chin canards were removed, and the aircraft was repainted in a standard Air Force scheme. A fuel drop tank is visible below the wing. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

Supersonic aerodynamic characteristics of an advanced F-16 derivative aircraft configuration

NASA Technical Reports Server (NTRS)

Fox, Mike C.; Forrest, Dana K.

1993-01-01

A supersonic wind tunnel investigation was conducted in the NASA Langley Unitary Plan Wind Tunnel on an advanced derivative configuration of the United States Air Force F-16 fighter. Longitudinal and lateral directional force and moment data were obtained at Mach numbers of 1.60 to 2.16 to evaluate basic performance parameters and control effectiveness. The aerodynamic characteristics for the F-16 derivative model were compared with the data obtained for the F-16C model and also with a previously tested generic wing model that features an identical plan form shape and similar twist distribution.

Stability and control characteristics of a three-surface advanced fighter configuration at angles of attack up to 45 deg. [conducted in the Langley 16-foot transonic tunnel

NASA Technical Reports Server (NTRS)

Henderson, W. P.; Leavitt, L. D.

1981-01-01

The tests were conducted at Mach numbers from 0.40 to 0.90, at angles of attack up to 45 deg for the lower Mach numbers, and at angles of sideslip up to 15 deg. The model variations under study included adding a canard surface and deflecting horizontal tails, ailerons, and rudders.

Conceptual design optimization study

NASA Technical Reports Server (NTRS)

Hollowell, S. J.; Beeman, E. R., II; Hiyama, R. M.

1990-01-01

The feasibility of applying multilevel functional decomposition and optimization techniques to conceptual design of advanced fighter aircraft was investigated. Applying the functional decomposition techniques to the conceptual design phase appears to be feasible. The initial implementation of the modified design process will optimize wing design variables. A hybrid approach, combining functional decomposition techniques for generation of aerodynamic and mass properties linear sensitivity derivatives with existing techniques for sizing mission performance and optimization, is proposed.

Redesigning of a Canard Control Surface of an Advanced Fighter Aircraft: Effect on Buckling and Aerodynamic Behavior

NASA Astrophysics Data System (ADS)

Shrivastava, Sachin; Mohite, P. M.

2015-01-01

A redesign of canard control-surface of an advanced all-metallic fighter aircraft was carried out by using carbon fibre composite (CFC) for ribs and panels. In this study ply-orientations of CFC structure are optimized using a Genetic-Algorithm (GA) with an objective function to have minimum failure index (FI) according to Tsai-Wu failure criterion. The redesigned CFC structure was sufficiently strong to withstand aerodynamic loads from stress and deflection points of view. Now, in the present work CFC canard structure has been studied for its buckling strength in comparison to existing metallic design. In this study, the existing metallic design was found to be weak in buckling. Upon a detailed investigation, it was revealed that there are reported failures in the vicinity of zones where initial buckling modes are excited as predicted by the finite element based buckling analysis. In view of buckling failures, the redesigned CFC structure is sufficiently reinforced with stringers at specific locations. After providing reinforcements against buckling, the twist and the camber variations of the airfoil are checked and compared with existing structure data. Finally, the modal analysis has been carried out to compare the variation in excitation frequency due to material change. The CFC structure thus redesigned is safe from buckling and aerodynamic aspects as well.

Experimental investigation of forebody and wing leading-edge vortex interactions at high angles of attack

NASA Technical Reports Server (NTRS)

Erickson, G. E.; Gilbert, W. P.

1983-01-01

An experimental investigation was conducted to assess the vortex flow-field interactions on an advanced, twin-jet fighter aircraft configuration at high angles of attack. Flow-field surveys were conducted on a small-scale model in the Northrop 0.41 - by 0.60-meter water tunnel and, where appropriate, the qualitative observations were correlated with low-speed wind tunnel data trends obtained on a large-scale model of the advanced fighter in the NASA Langley Research Center 30- by 60-foot (9.1- by 18.3-meter) facility. Emphasis was placed on understanding the interactions of the forebody and LEX-wing vortical flows, defining the effects on rolling moment variation with sideslip, and identifying modifications to control or regulate the vortex interactions at high angles of attack. The water tunnel flow visualization results and wind tunnel data trend analysis revealed the potential for strong interactions between the forebody and LEX vortices at high angles of attack. In particular, the forebody flow development near the nose could be controlled by means of carefully-positioned radome strakes. The resultant strake-induced flow-field changes were amplified downstream by the more powerful LEX vortical motions with subsequent large effects on wing flow separation characteristics.

Agile and Adaptive IT Ecosystem, Results, Outlook, and Recommendations

DTIC Science & Technology

2014-06-01

http://netbeans.dzone.com/news/war-fighter- netbeans -platform 5 http://www.afei.org/events/4A07/Documents/1-DI2E%20Brochure%20ISA_10APR13.pdf 6...Client ( NetBeans ), and OSGI bundles (Karafe). DoD systems also use both the Android and iOS mobile operating systems. Each technology has a specific

Integrated Mission Precision Attack Cockpit Technology (IMPACT). Phase 1: Identifying Technologies for Air-to-Ground Fighter Integration.

DTIC Science & Technology

1994-10-31

No comment S4: No comment 63 3. The HMD would my...released (i.e., not hung) without looking down on the PACS page is very good." S4: No comment 6. The HMD would my SITUATIONAL AWARENESS during the INGRESS...Substantially Degrade 0 (Subject 1: NO RATING) HOW? S 1: No comment S2: "Previous reasons, visibility REF # 2, 4" S3: No comment S4: No comment 65 7. The

Air Weapon Systems in the Third World: A Combat Potential Assessment Technique.

DTIC Science & Technology

1986-06-01

VALUE LABEL BMAT BOMBER-GROUND ATTACK FTAT FIGHTER-GROUND ATTACK FTTA FIGHTER/TRAINER-GROUND ATTACK FTIN FIGHTER-INTERCEPTOR FTTI FIGHTER/TRAINER...260 2.91 10900 5440 17720 24540 TORADV FTIN 46 400 5.20 31500 15632 41392 60000 TORIDS FTAT 46 400 5.20 31065 14000 47985 60000 TU16AG BMAT 108 1772...6.58 82000 56870 130235 158730 TU22BD BMAT 91 1451 5. 69 80400 81600 147650 185000 ACFT MAXPWR TWPWR ASPD SPECENA LSPD SPECENS CSPD SCEI ALPHAMSI 5952

Editorial on Future Jet Technologies

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2014-12-01

The jet engine is the prime flight controller in post-stall flight domains where conventional flight control fails, or when the engine prevents catastrophes in training, combat, loss of all airframe hydraulics (the engine retains its own hydraulics), loss of one engine, pilot errors, icing on the wings, landing gear and runway issues in takeoff and landing and in bad-whether recoveries. The scientific term for this revolutionary technology is "jet-steering", and in engineering practice - "thrust vectoring", or "TV". Jet-Steering in advanced fighter aircraft designs is integrated with stealth technology. The resulting classified Thrust-Vectoring-Stealth ("TVS") technology has generated a second jet-revolution by which all Air-&-Sea-Propulsion Science and R&D are now being reassessed. Classified F-22, X-47B/C and RQ-180 TVS-vehicles stand at the front of this revolution. But recent transfers of such sensitive technologies to South Korea and Japan [1-5], have raised various fundamental issues that are evaluated by this editorial-review. One, and perhaps a key conclusion presented here, means that both South Korea and Japan may have missed one of their air-&-sea defenses: To develop and field low-cost unmanned fleets of jet-drones, some for use with expensive, TVS-fighter aircraft in highly congested areas. In turn, the U.S., EU, Russia and China, are currently developing such fleets at various TVS levels and sizes. China, for instance, operates at least 15,000 drones ("UAVs") by 2014 in the civilian sector alone. All Chinese drones have been developed by at least 230 developers/manufacturers [1-16]. Mobile telecommunication of safe links between flyers and combat drones ("UCAVs") at increasingly deep penetrations into remote, congested areas, can gradually be purchased-developed-deployed and then operated by extant cader of tens of thousands "National Champion Flyers" who have already mastered the operation of mini-drones in free-to-all sport clubs under national competions and Awards. [Rule-13]. We also provide 26 references [17-43] to a different, unclassified technology that enhances TV-induced flight safety for passenger jets, turboprops and helicopters. It is based on patented stowed-away/emergency-deployed TV-kits added to fixed-configuration, subsonic exhaust nozzles of low thrust-to-weight ratio vehicles. Expected benefits include anti-terror recoveries from emergencies, like forced landing on unprepared runways or highways, or recoveries from all airframe-hydraulics-outs, asymmetric ice on wings, landing gear catastrophes, and recoveries from pilot errors and bad-whether incidents [Rule 9(7)]. Other TV technologies involve preventing catastrophes in speed and patrol boats, racing and regular cars/SUVs, buses and trucks. [Rule 9(8)] and faster helicopters [Rule 9(10)].

Weapon system simulation in flight (WaSiF)

NASA Astrophysics Data System (ADS)

Bartoldus, Klaus H.

2005-05-01

The research and technology demonstration program was co-funded by the Ministries of Defence of five European countries under the framework of the "EUropean Cooperation for the Long term in Defence" (EUCLID) MoU to include Germany, Italy, The Netherlands, Portugal and Turkey with considerable financial contribution from the industrial entities. EADS Military Aircraft Munich has led a team of seven industries and research centers, including Aermacchi of Italy, DutchSpace and NLR of The Netherlands, OGMA and INETI of Portugal and Marmara Research Center of Turkey. The purpose of the project was the design, realization and demonstration of an embedded real time simulation system allowing the combat training of operational aircrew in a virtual air defence scenario and threat environment against computer generated forces in the air and on the ground while flying on a real aircraft. The simulated scenario is focused on air-to-air beyond visual range engagements of fighter aircraft. WaSiF represents one of the first demonstrations of an advanced embedded real time training system onboard a fighter/training aircraft. The system is integrated onboard the MB339CX aircraft. The overall flight test activity covered a wide variety of test conditions for a total of 21 test flights; the operational airborne time of the WaSiF amounted to nearly 18 hours. The demonstration and evaluation were quite positive; the five-nation aircrew was very fond of their first encounter with the virtual world in the military flight training. A common view and approach towards Network Centric Warfare is but emerging. WaSiF in a future networked configuration holds lots of promise to serve the needs of Integrated Air Defence: Common training in a virtual environment.

F-18 HARV research pilot Dana Purifoy

NASA Technical Reports Server (NTRS)

1996-01-01

Dana D. Purifoy is an aerospace research pilot at NASA's Dryden Flight Research Center, Edwards, California. He joined NASA in August 1994. Purifoy is a former Air Force test pilot who served as a project pilot in the joint NASA/Air Force X-29 Forward Swept Wing research program conducted at Dryden from 1984 to 1991. His most recent assignment in the Air Force was flying U-2 aircraft as a test pilot at Air Force Plant 42, Palmdale, CA. In addition to flying the X-29 at Dryden as an Air Force pilot, Purifoy also served as project pilot and joint test force director with the AFTI F-16 (Advanced Fighter Technology Integration/F-16) program, also located at Dryden. Before his assignments as project pilot on the X-29 and AFTI/F-16 aircraft, Purifoy was chief of the Academics Systems Branch at the Air Force Test Pilot School at Edwards. Prior to becoming a test pilot, he flew F-111 and F-16 aircraft in Great Britain and Germany. He has accumulated 3800 hours of flying time in his career. The final flight for the F-18 High Alpha Research Vehicle (HARV) took place at NASA Dryden on May 29, 1996. The highly modified F-18 airplane flew 383 flights over a nine year period and demonstrated concepts that greatly increase fighter maneuverability. Among concepts proven in the aircraft is the use of paddles to direct jet engine exhaust in cases of extreme altitudes where conventional control surfaces lose effectiveness. Another concept, developed by NASA Langley Research Center, is a deployable wing-like surface installed on the nose of the aircraft for increased right and left (yaw) control on nose-high flight angles.

Flight Test Results for the F-16XL With a Digital Flight Control System

NASA Technical Reports Server (NTRS)

Stachowiak, Susan J.; Bosworth, John T.

2004-01-01

In the early 1980s, two F-16 airplanes were modified to extend the fuselage length and incorporate a large area delta wing planform. These two airplanes, designated the F-16XL, were designed by the General Dynamics Corporation (now Lockheed Martin Tactical Aircraft Systems) (Fort Worth, Texas) and were prototypes for a derivative fighter evaluation program conducted by the United States Air Force. Although the concept was never put into production, the F-16XL prototypes provided a unique planform for testing concepts in support of future high-speed supersonic transport aircraft. To extend the capabilities of this testbed vehicle the F-16XL ship 1 aircraft was upgraded with a digital flight control system. The added flexibility of a digital flight control system increases the versatility of this airplane as a testbed for aerodynamic research and investigation of advanced technologies. This report presents the handling qualities flight test results covering the envelope expansion of the F-16XL with the digital flight control system.

The sharing of radiological images by professional mixed martial arts fighters on social media.

PubMed

Rahmani, George; Joyce, Cormac W; McCarthy, Peter

2017-06-01

Mixed martial arts is a sport that has recently enjoyed a significant increase in popularity. This rise in popularity has catapulted many of these "cage fighters" into stardom and many regularly use social media to reach out to their fans. An interesting result of this interaction on social media is that athletes are sharing images of their radiological examinations when they sustain an injury. To review instances where mixed martial arts fighters shared images of their radiological examinations on social media and in what context they were shared. An Internet search was performed using the Google search engine. Search terms included "MMA," "mixed martial arts," "injury," "scan," "X-ray," "fracture," and "break." Articles which discussed injuries to MMA fighters were examined and those in which the fighter themselves shared a radiological image of their injury on social media were identified. During our search, we identified 20 MMA fighters that had shared radiological images of their injuries on social media. There were 15 different types of injury, with a fracture of the mid-shaft of the ulna being the most common. The most popular social media platform was Twitter. The most common imaging modality X-ray (71%). The majority of injuries were sustained during competition (81%) and 35% of these fights resulted in a win for the fighter. Professional mixed martial artists are sharing radiological images of their injuries on social media. This may be in an attempt to connect with fans and raise their profile among other fighters.

Future Jet Technologies. Part B. F-35 Future Risks v. JS-Education of Pilots & Engineers

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2011-09-01

Design of “Next-Generation” airframes based on supermarket-jet-engine-components is nowadays passé. A novel integration methodology [Gal-Or, “Editorial-Review, Part A”, 2011, Gal-Or, “Vectored Propulsion, Supermaneuverability and Robot Aircraft”, Springer Verlag, Gal-Or, Int'l. J. of Thermal and Fluid Sciences 7: 1-6, 1998, “Introduction”, 2011] is nowadays in. For advanced fighter aircraft it begins with JS-based powerplant, which takes up to three times longer to mature vis-à-vis the airframe, unless “committee's design” enforces a dormant catastrophe. Jet Steering (JS) or Thrust Vectoring Flight Control, is a classified, integrated engine-airframe technology aimed at maximizing post-stall-maneuverability, flight safety, efficiency and flight envelopes of manned and unmanned air vehicles, especially in the “impossible-to-fly”, post-stall flight domains where the 100+ years old, stall-spin-limited, Conventional Flight Control fails. Worldwide success in adopting the post-stall, JS-revolution, opens a new era in aviation, with unprecedented design variables identified here for a critical review of F-35 future risks v. future fleets of jet-steered, pilotless vehicles, like the X-47B/C. From the educational point of view, it is also instructive to comprehend the causes of long, intensive opposition to adopt post-stall, JS ideas. A review of such debates may also curb a future opposition to adopt more advanced, JS-based technologies, tests, strategies, tactics and missions within the evolving air, marine and land applications of JS. Most important, re-education of pilots and engineers requires adding post-stall, JS-based studies to curriculum & R&D.

Education for Public Service.

ERIC Educational Resources Information Center

New England Board of Higher Education, Wellesley, MA.

Issues in the improvement of training for fire fighters and officer personnel were taken up in ten symposium papers. Session 1 covered legal and other constraints that affect what a fire fighter should know; and current practices in volunteer, rural, and municipal fire fighter training in the United States. Papers from the other sessions dealt…

76 FR 31613 - NIOSH Fire Fighter Fatality Investigation and Prevention Program (FFFIPP)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

... NIOSH-063B] NIOSH Fire Fighter Fatality Investigation and Prevention Program (FFFIPP) AGENCY: The... Fire Fighter Fatality Investigation and Prevention Program (FFFIPP). NIOSH is seeking stakeholder input on the FFFIPP to ensure that the program is meeting the needs and expectations of the U.S. fire...

Learning amongst Norwegian Fire-Fighters

ERIC Educational Resources Information Center

Sommer, Morten; Nja, Ove

2011-01-01

Purpose: The purpose of this study is to reveal and analyse dominant learning processes in emergency response work from the fire-fighters' point of view, and how fire-fighters develop their competence. Design/methodology/approach: This study adopted an explorative approach using participant observation. The objective of this open-minded approach…

Program Fighter: An Evaluation.

ERIC Educational Resources Information Center

Hull, David G.; Fowler, Wallace T.

A computer program for the sizing of subsonic and supersonic fighter planes was adapted for use in an aerospace engineering course at the University of Texas at Austin. FIGHTER uses classroom notation and separate subroutines for different disciplines to implement the conceptual design process. Input consists of a set of design variables and a set…

Absorbing and Developing Qualified Fighter Pilots. The Role of the Advanced Simulator

DTIC Science & Technology

2007-01-01

This document and trademark(s) contained herein are protected by law as indicated in a notice appearing later in this work . This electronic...NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) RAND Corporation,1776 Main Street,Santa Monica,CA,90401-3208 8...should be available to all pilots working with given a mission design series. Funding for fielding new systems, providing ongoing essential software

Absorbing and Developing Qualified Fighter Pilots. The Role of the Advanced Simulator

DTIC Science & Technology

2007-01-01

This document and trademark(s) contained herein are protected by law as indicated in a notice appearing later in this work . This electronic...NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Rand Corporation...be available to all pilots working with given a mission design series. Funding for fielding new systems, providing ongoing essential software

Design and Development of Anthropometrically Correct Head Forms for Joint Strike Fighter Ejection Seat Testing

DTIC Science & Technology

2005-02-01

Testing John A. Plaga Air Force Research Laboratory Chris Albery Mark Boehmer Chuck Goodyear Glenn Thomas Advanced...PROJECT NUMBER 7184 5e. TASK NUMBER 02 6. AUTHOR(S) John A. Plaga *Chris Albery *Mark Boehmer *Chuck Goodyear *Glenn Thomas 5f. WORKUNIT...laser scan 16. SECURITY CLASSIFICATION OF: 19a. NAME OF RESPONSIBLE PERSON: John A. Plaga a. REPORT U b. ABSTRACT U c. THIS PAGE U 17

Operations Odyssey Dawn and Unified Protector: Another Win for Warden s Theory

DTIC Science & Technology

2014-12-04

Gortney’s response was clear, “they were mechanized positions and they were advancing on Benghazi. And so to protect the Libyan people we took them under ...them under attack.” Targeting the fielded forces played a primary role in protecting the Libyan people. Coalition fighter aircraft targeted... protection of civilians, with the major limitation of prohibiting foreign ground forces from the operations. Because of this limitation, airpower was the

Advanced Airborne Defensive Laser for Incorporation on Strike Fighter Aircraft

DTIC Science & Technology

2017-09-01

Systems within the Pod The Cyclops pod contains several systems working together to perform the high - level functions. The status of these systems must be...by the aircraft is limited, and Cyclops power requirements are high . commercial off-the-shelf (COTS) Ram Air Turbines are available and are...Supply Subsystem The Cyclops pod must generate its own power due to lack of available power from the aircraft; therefore, the Power supply has high

Air Sea Battle Intelligence, Surveillance, and Reconnaissance Concept of Operations: Getting Back to Fundamentals

DTIC Science & Technology

2012-05-08

Assessment” phase. This phase will be constant throughout the AirSea Battle. A subset of this phase includes battle damage assessment ( BDA ). BDA ...taskings for assessment. There may be situations where operations will cease until the proper BDA is desired. This possibility directly... BDA assessments. It is paramount to task fifth generation fighter with this mission set due to their advanced capabilities. 15 The USAF and USN

Gain selection method and model for coupled propulsion and airframe systems

NASA Technical Reports Server (NTRS)

Murphy, P. C.

1982-01-01

A longitudinal model is formulated for an advanced fighter from three subsystem models: the inlet, the engine, and the airframe. Notable interaction is found in the coupled system. A procedure, based on eigenvalue sensitivities, is presented which indicates the importance of the feedback gains to the optimal solution. This allows ineffectual gains to be eliminated; thus, hardware and expense may be saved in the realization of the physical controller.

Three Dimensional Grid Generation for Complex Configurations - Recent Progress

DTIC Science & Technology

1988-03-01

Navier/Stokes finite difference calculations currently of interest. It has been amply demonstrated that the viability of a numerical solution depends...such as advanced fighters or logistic transports, where a multiblock mesh, for example, is necessary. There exist numerous reports and books on the...MESHES I 3.10 ADAPTIVE GRID SCHEMES 10 3.11 REFERENCES 12 4. CONTRIBUTIONS 13 4.1 SOLICITATION AND OVERVIEW 13 4.2 LESSONS LEARNED IN THE MESH

Why Adolescents Fight: A Qualitative Study of Youth Perspectives on Fighting and Its Prevention

PubMed Central

Shetgiri, Rashmi; Lee, Simon C.; Tillitski, John; Wilson, Connie; Flores, Glenn

2014-01-01

Objective Identify risk factors for fighting, factors that protect against fighting, and strategies to prevent fighting, among adolescents who fight and those uninvolved in fighting. Methods Focus groups were conducted with middle and high-school students, stratified by fighting (fighter/non-fighter) status, race/ethnicity, and gender. Groups were audiotaped, transcribed, and analyzed using margin coding and thematic content analysis. Themes were independently identified by three coders; disagreements were resolved by consensus. Results The 65 participants in the 12 focus groups were 13–17 years old. Reasons for fighting include self-defense, to gain/maintain respect, or due to anger; having goals for the future is protective. Non-fighters state that their parents condone fighting only when physically attacked, and teach adolescents strategies to avoid fighting. Fighters describe mixed messages from parents, and pro-fighting attitudes and modeling of aggressive behavior among some family members. Non-fighters avoid fighting by ignoring insults or walking away. Fighters feel unable to use nonviolent conflict-resolution methods effectively. Peers may instigate or encourage fights. Suggested prevention strategies include anger-management and conflict-resolution programs, relationships with caring adults, and physicians counseling youth about the consequences of fighting. Conclusions Non-fighters use various strategies to avoid fighting, whereas fighters are aware of few alternatives to fighting. Conflicting parental messages about fighting may enhance the likelihood of fighting. Physicians can counsel youth about the negative consequences of fighting. Interventions that teach anger management and conflict resolution, promote adolescent self-efficacy for using non-violent strategies, and address parental attitudes about fighting may be effective in preventing fighting. PMID:25528128

75 FR 40845 - Preventing Deaths and Injuries of Fire Fighters Using Risk Management Principles at Structure Fires

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-14

... NIOSH 141-A] Preventing Deaths and Injuries of Fire Fighters Using Risk Management Principles at Structure Fires AGENCY: National Institute for Occupational Safety and Health (NIOSH) of the Centers for... publication entitled ``Preventing Deaths and Injuries of Fire Fighters Using Risk Management Principles at...

Fire Fighter Level I-II-III [and] Practical Skills Test. Wisconsin Fire Service Certification Series. Final Revision.

ERIC Educational Resources Information Center

Pribyl, Paul F.

Practical skills tests are provided for fire fighter trainees in the Wisconsin Fire Service Certification Series, Fire Fighter Levels I, II, and III. A course introduction appears first and contains this information: recommended instructional sequence, required facilities, instructional methodology, requirements for certification, course…

Electro-optic architecture for servicing sensors and actuators in advanced aircraft propulsion systems

NASA Technical Reports Server (NTRS)

Poppel, G. L.; Glasheen, W. M.

1989-01-01

A detailed design of a fiber optic propulsion control system, integrating favored sensors and electro-optics architecture is presented. Layouts, schematics, and sensor lists describe an advanced fighter engine system model. Components and attributes of candidate fiber optic sensors are identified, and evaluation criteria are used in a trade study resulting in favored sensors for each measurand. System architectural ground rules were applied to accomplish an electro-optics architecture for the favored sensors. A key result was a considerable reduction in signal conductors. Drawings, schematics, specifications, and printed circuit board layouts describe the detailed system design, including application of a planar optical waveguide interface.

Environmental Assessment for Employment of a Mobile Laser Evaluator System (LES-M) for the 20th Fighter Wing at Shaw Air Force Base, South Carolina

DTIC Science & Technology

2004-05-01

Environmental Assessment for Employment of a Mobile Laser Evaluator System (LES-M) for the 20th Fighter Wing at Shaw Air Force Base, South Carolina...Mobile Laser Evaluator System (LES-M) for the 20th Fighter Wing at Shaw Air Force Base, South Carolina 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM...a Mobile Laser Evaluator System (LES-M) for the 20’’ Fighter Wing (20 fW) at Shaw Air Force Base (AFB), South Carolir.a DESCRIPTION OF THE PROPOSED

Energy Efficient Materials Manufacturing from Secondary Resources

NASA Astrophysics Data System (ADS)

Apelian, Diran; Mishra, Brajendra

Rare earths metals, including yttrium and scandium, are being increasingly used in clean energy technologies, colored phosphors, lasers and high intensity magnets. There are important defense applications such as fighter jet engines, missile guidance systems and space based satellite and communication systems, based on these metals. The commitment to clean energy technologies by various governments, as well as the projected growth in power and transportation sectors across the globe will certainly escalate the demand for rare earth metals and compounds. This demand implies that to ensure unhindered technological innovation, it is essential to possess secure supply chains for rare earth elements. The United States continues to be one of the largest consumers and importer of rare earths and the trend is expected to continue as the demand increases. In order to ensure secure rare earth supply and attenuate supply-demand imbalances post 2014, it is not only necessary to encourage and support exploration of newer reserves, build a rare earth stockpile, but it is also of utmost importance to look at opportunities to recycle and reuse Rare Earth Elements (REE) from secondary sources, such as post-consumer and manufacturing process wastes. This research describes the technological developments made to convert these valuable resources into functional manufactured materials for lighting industry, automotive and petroleum refining catalysts, and high density permanent magnets. In addition, production of rhenium from advanced aerospace alloys is also discussed from the perspective that it can be recovered for introduction in turbine alloys.

Light weight, high-speed, and self-powered wireless fiber optic sensor (WiFOS) structural health monitor system for avionics and aerospace environments

NASA Astrophysics Data System (ADS)

Mendoza, Edgar A.; Kempen, Cornelia; Sun, Sunjian; Esterkin, Yan

2014-09-01

This paper describes recent progress towards the development of an innovative light weight, high-speed, and selfpowered wireless fiber optic sensor (WiFOS™) structural health monitor system suitable for the onboard and in-flight unattended detection, localization, and classification of load, fatigue, and structural damage in advanced composite materials commonly used in avionics and aerospace systems. The WiFOS™ system is based on ROI's advancements on monolithic photonic integrated circuit microchip technology, integrated with smart power management, on-board data processing, wireless data transmission optoelectronics, and self-power using energy harvesting tools such as solar, vibration, thermoelectric, and magneto-electric. The self-powered, wireless WiFOS™ system offers a versatile and powerful SHM tool to enhance the reliability and safety of avionics platforms, jet fighters, helicopters, commercial aircraft that use lightweight composite material structures, by providing comprehensive information about the structural integrity of the structure from a large number of locations. Immediate SHM applications are found in rotorcraft and aircraft, ships, submarines, and in next generation weapon systems, and in commercial oil and petrochemical, aerospace industries, civil structures, power utilities, portable medical devices, and biotechnology, homeland security and a wide spectrum of other applications.

AMLCD cockpit: promise and payoffs

NASA Astrophysics Data System (ADS)

Snow, Michael P.; Jackson, Timothy W.; Meyer, Frederick M.; Reising, John M.; Hopper, Darrel G.

1999-08-01

The active matrix liquid crystal display (AMLCD) has become the preferred flight instrument technology in avionics multifunction display applications. Current bubble canopy fighter cockpit applications involve sizes up to 7.8 X 7.8 in. active display. Dual use avionics versions of AMLCD technology are now as large as 6.7 X 6.7 in. active display area in the ARINC D sized color multifunction display (MFD). This is the standard instrument in all new Boeing transport aircraft and is being retrofitted into the C-17A. A special design of the ARINC D instrument is used in the Space Shuttle cockpit upgrade. Larger sizes of AMLCD were desired when decisions were made in the early 1990s for the F-22. Commercial AMLCD technology has now produced monitors at 1280 X 1024 resolution (1.3 megapixels) in sizes of 16 to 21 in. diagonal. Each of these larger AMLCDs has more information carrying capacity than the entire F-22A cockpit instrument panel shipset, comprising six separate smaller AMLCDs (1.2 megapixels total). The larger AMLCDs are being integrated into airborne mission crewstations for use in dim ambient lighting conditions. It is now time to identify and address the technology challenges of upgrading these larger AMLCDs for sunlight readable application and of developing concepts for their integration into advanced bubble canopy fighter cockpits. The overall goals are to significantly increase the informational carrying capacity to bring both sensor and information fusion into the cockpit and, thereby, to enable a significant increase in warfighter situational awareness and effectiveness. A research cockpit was built using specialized versions of the IBM 16.1 in and two smaller 10 in. AMLCDs to examine human factors and display design issues associated with these next-generation AMLCD cockpit displays. This cockpit was later upgraded to allow greater reconfigurability and flexibility in the display hardware used to conduct part- task mission simulations. The objective optical characterization of the AMLCDs used in this simulator and the cockpit design are described. Display formats under consideration for test in this cockpit are described together with some of the basic human factors engineering issues involved. Studies conducted in this cockpit will be part of an ongoing joint effort of the hardware-focused aerospace displays team and the pilot-focused human factors team in the Air Force Research Laboratory's Crew System Interface Division. The objective of these studies is to ascertain the payoffs of the large AMLCD promise in combat cockpits.

Sneaker Males Affect Fighter Male Body Size and Sexual Size Dimorphism in Salmon.

PubMed

Weir, Laura K; Kindsvater, Holly K; Young, Kyle A; Reynolds, John D

2016-08-01

Large male body size is typically favored by directional sexual selection through competition for mates. However, alternative male life-history phenotypes, such as "sneakers," should decrease the strength of sexual selection acting on body size of large "fighter" males. We tested this prediction with salmon species; in southern populations, where sneakers are common, fighter males should be smaller than in northern populations, where sneakers are rare, leading to geographical clines in sexual size dimorphism (SSD). Consistent with our prediction, fighter male body size and SSD (fighter male∶female size) increase with latitude in species with sneaker males (Atlantic salmon Salmo salar and masu salmon Oncorhynchus masou) but not in species without sneakers (chum salmon Oncorhynchus keta and pink salmon Oncorhynchus gorbuscha). This is the first evidence that sneaker males affect SSD across populations and species, and it suggests that alternative male mating strategies may shape the evolution of body size.

China Naval Modernization: Implications for U.S. Navy Capabilities - Background and Issues for Congress

DTIC Science & Technology

2011-07-11

12 Russian-made Kilo-class submarines). China’s large inventory of ASCMs also includes several indigenous designs. In August 2010, it was reported...based naval aircraft inventory includes, among other things, 24 Russian-made Su-30 MKK 2 Flanker land-based fighters, whose delivery was completed in...advanced Type 095 SSNs to the inventory in the coming years. China has 13 SONG-class (Type 039) diesel-electric attack submarines (SS) in its

Samarium Cobalt (SmCo) Generator/Engine Integration Study

DTIC Science & Technology

1980-04-01

110o1110 (Cole Ms -W~ Daiwa. to* J11 tuo.in Wfi wee -004"ni Aircraft Generator/starter Samarium Cobalt Turbine Engine , Feasibility Secondary Power...integration into the main rotor system of typical aircraft gas turbine engines . A major objective is the definition of the engine interface for such... Engine The F404 is a low bypass, augmented turbofan Pngine developed for application in advanced fighter aircraft (F-18). This type of engine benefits most

Low-speed longitudinal aerodynamic characteristics of a flat-plate planform model of an advanced fighter configuration

NASA Technical Reports Server (NTRS)

Mcgrath, Brian E.; Neuhart, Dan H.; Gatlin, Gregory M.; Oneil, Pat

1994-01-01

A flat-plate wind tunnel model of an advanced fighter configuration was tested in the NASA LaRC Subsonic Basic Research Tunnel and the 16- by 24-inch Water Tunnel. The test objectives were to obtain and evaluate the low-speed longitudinal aerodynamic characteristics of a candidate configuration for the integration of several new innovative wing designs. The flat plate test allowed for the initial evaluation of the candidate planform and was designated as the baseline planform for the innovative wing design study. Low-speed longitudinal aerodynamic data were obtained over a range of freestream dynamic pressures from 7.5 psf to 30 psf (M = 0.07 to M = 0.14) and angles-of-attack from 0 to 40 deg. The aerodynamic data are presented in coefficient form for the lift, induced drag, and pitching moment. Flow-visualization results obtained were photographs of the flow pattern over the flat plate model in the water tunnel for angles-of-attack from 10 to 40 deg. The force and moment coefficients and the flow-visualization photographs showed the linear and nonlinear aerodynamic characteristics due to attached flow and vortical flow over the flat plate model. Comparison between experiment and linear theory showed good agreement for the lift and induced drag; however, the agreement was poor for the pitching moment.

Root Cause Analyses of Nunn-McCurdy Breaches, Volume 1: Zumwalt-Class Destroyer, Joint Strike Fighter, Longbow Apache and Wideband Global Satellite

DTIC Science & Technology

2011-01-01

E) in March 2012.4 This would amount to a concurrency of about 25 percent for the JSF.5 Con- currency for the F-22, an equally challenging technology...overall price deflator by OSD to convert constant into current dollars. 6 The xenon ion propulsion system, certain transponders, and a crypto box

ICT as a Catalyst in Problem-Based Learning Processes? A Comparison of Online and Campus-Based PBL in Swedish Fire-Fighter Training

ERIC Educational Resources Information Center

Holmgren, Robert

2013-01-01

This article focuses on the impact on learning processes when digital technologies are integrated into PBL (problem-based learning) oriented distance training. Based on socio-cultural perspectives on learning and a comparative distance-campus as well as a time-perspective, instructor and student roles, and learning activities were explored.…

ARC-1945-A-7121

NASA Image and Video Library

1945-02-06

North American P-51B 'Mustang' fighter in flight over bay area. The P-51 with its new laminar-flow wing sections developed by NACA was the first airplane selected for testing of airplane drag in flight and wind tunnel comparison NOTE: used in NASA Publication; Flight Research at Ames: 57 Years of Development and Validation of Aeronautical Technology' Transonic Model Testing fig. 9 NASA SP-1998-3300

Defeating the IED: JIEDDO’s Mission Impossible, the Lure of Technology, and the Emergence of the COIN Solution

DTIC Science & Technology

2011-04-12

8 Figure 4 : MaxxPro MRAP Vehicle ......................................................... 13...armored military vehicles , to demonstrate, often through the dissemination of video clips of attacks, the ability of overmatched irregular fighters to...34 vehicles , such as main battle tanks, were designed for. Additionally, the U.S. military is dependent on wheeled vehicles and roads for almost all combat

Integrated Unit Deployments: Rethinking Air National Guard Fighter Mobilizations

DTIC Science & Technology

2016-06-01

INTEGRATED UNIT DEPLOYMENTS: RETHINKING AIR NATIONAL GUARD FIGHTER MOBILIZATIONS BY MAJOR ANDREW P. JACOB A THESIS...This study comprises an analysis of the mobilization and deployment of Air National Guard fighter aircraft units in a search for an efficient and... mobilization . This thesis suggests that Integrated Unit Deployments will provide the balance between Air National Guard overseas deployments and

78 FR 52135 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental To...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-22

... Tactics Development and Evaluation (TD&E) Program. Multiple munitions (bombs, missiles, and gunner rounds... laser-guided Mk-84 bomb F-16C fighter aircraft. GBU-24 laser-guided Mk-84 bomb F-16C+ fighter aircraft... bomb. GBU-12 laser-guided Mk-82 bomb A-10 fighter aircraft. GBU-38 Joint Direct Attack Munition, global...

78 FR 33357 - Takes of Marine Mammals Incidental to Specified Activities; Taking Marine Mammals Incidental to...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-04

...) Program. Multiple munitions (bombs, missiles, and gunner rounds) and aircraft would be used to meet the... with Munitions specific munitions) GBU-10 laser-guided Mk-84 bomb F-16C fighter aircraft. GBU-24 laser-guided Mk-84 bomb F-16C+ fighter aircraft. GBU-31 Joint Direct Attack Munition, F-15E fighter aircraft...

Training and Education in the Fire Services (Proceedings of a Symposium, April 8-9 1970).

ERIC Educational Resources Information Center

National Academy of Sciences-National Research Council, Washington, DC. Div. of Engineering.

Issues in the improvement of training for fire fighters and officer personnel were taken up in ten symposium papers. Session I covered legal and other constraints that affect what a fire fighter should know; and current practices in volunteer, rural, and municipal fire fighter training in the United States. Papers from the other sessions dealt…

A knowledge-based system design/information tool for aircraft flight control systems

NASA Technical Reports Server (NTRS)

Mackall, Dale A.; Allen, James G.

1989-01-01

Research aircraft have become increasingly dependent on advanced control systems to accomplish program goals. These aircraft are integrating multiple disciplines to improve performance and satisfy research objectives. This integration is being accomplished through electronic control systems. Because of the number of systems involved and the variety of engineering disciplines, systems design methods and information management have become essential to program success. The primary objective of the system design/information tool for aircraft flight control system is to help transfer flight control system design knowledge to the flight test community. By providing all of the design information and covering multiple disciplines in a structured, graphical manner, flight control systems can more easily be understood by the test engineers. This will provide the engineers with the information needed to thoroughly ground test the system and thereby reduce the likelihood of serious design errors surfacing in flight. The secondary objective is to apply structured design techniques to all of the design domains. By using the techniques in the top level system design down through the detailed hardware and software designs, it is hoped that fewer design anomalies will result. The flight test experiences of three highly complex, integrated aircraft programs are reviewed: the X-29 forward-swept wing, the advanced fighter technology integration (AFTI) F-16, and the highly maneuverable aircraft technology (HiMAT) program. Significant operating anomalies and the design errors which cause them, are examined to help identify what functions a system design/information tool should provide to assist designers in avoiding errors.

Aircrew Sizing Survey 2011

DTIC Science & Technology

2014-10-01

Resource JSF Joint Strike Fighter JPATS Joint Primary Aircraft Training System USMC United States Marine Corps USAF United States Air Force LIST...Surface Anthropometry Resource (CAESAR) was developed for the Joint Strike Fighter (JSF) program. The ACSS was intended to replace the JSF-CAESAR...an aircrew sample was made in 2003 by Hudson et al. They extracted a subset, named JSF CAESAR (Joint Strike Fighter), from the Civilian American and

AFTI/F-16 in flight

NASA Technical Reports Server (NTRS)

1989-01-01

Overhead photograph of the AFTI F-16 painted in a non-standard gray finish, taken during a research flight in 1989. The two sensor pods are visible on the fuselage just forward of the wings and one of the two chin canards can be seen as a light-colored triangle ahead of one of the pods. A Sidewinder air-to-air missile is mounted on each wing tip. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

Preliminary design of a supersonic Short-Takeoff and Vertical-Landing (STOVL) fighter aircraft

NASA Technical Reports Server (NTRS)

1990-01-01

A preliminary study of a supersonic short takeoff and vertical landing (STOVL) fighter is presented. Three configurations (a lift plus lift/cruise concept, a hybrid fan vectored thrust concept, and a mixed flow vectored thrust concept) were initially investigated with one configuration selected for further design analysis. The selected configuration, the lift plus lift/cruise concept, was successfully integrated to accommodate the powered lift short takeoff and vertical landing requirements as well as the demanding supersonic cruise and point performance requirements. A supersonic fighter aircraft with a short takeoff and vertical landing capability using the lift plus lift/cruise engine concept seems a viable option for the next generation fighter.

Metal Organic Chemical Vapor Deposition of Oxide Films for Advanced Applications

DTIC Science & Technology

2000-06-01

coatings , photovoltaics, touch sensitive controls, electromagnetic shielding (as found on microwave ovens and stealth fighters), static dissipaters, and so...depositing high quality films. The methods are physical vapor deposition ( PVD ), spin/mist deposition, (CVD), and alternating layer (AL) CVD. PVD ...PZT & SBT, YBa2Cu3O, CeO, InO, TCOs, Varistors Ta2O5 , ZrO, MnO, HfO, CeO, MnO, MgO SAW/microwave Silicon/: Si, SiGe, SiGeC, �. Opto-electronics

Missile aerodynamics; Proceedings of the Conference, Monterey, CA, Oct. 31-Nov. 2, 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendenhall, M.R.; Nixon, D.; Dillenius, M.F.E.

1989-01-01

The present conference discusses the development status of predictive capabilities for missile aerodynamic characteristics, the application of experimental techniques to missile-release problems, prospective high-performance missile designs, the use of lateral jet controls for missile guidance, and the integration of stores on modern tactical aircraft. Also discussed are semiempirical aerodynamic methods for preliminary design, high angle-of-attack behavior for an advanced missile, and the dynamic derivatives of missiles and fighter-type configurations at high angles-of-attack.

Determinants of maximal oxygen uptake (VO2 max) in fire fighter testing.

PubMed

Vandersmissen, G J M; Verhoogen, R A J R; Van Cauwenbergh, A F M; Godderis, L

2014-07-01

The aim of this study was to evaluate current daily practice of aerobic capacity testing in Belgian fire fighters. The impact of personal and test-related parameters on the outcome has been evaluated. Maximal oxygen uptake (VO2 max) results of 605 male fire fighters gathered between 1999 and 2010 were analysed. The maximal cardio respiratory exercise tests were performed at 22 different centres using different types of tests (tread mill or bicycle), different exercise protocols and measuring equipment. Mean VO2 max was 43.3 (SD = 9.8) ml/kg.min. Besides waist circumference and age, the type of test, the degree of performance of the test and the test centre were statistically significant determinants of maximal oxygen uptake. Test-related parameters have to be taken into account when interpreting and comparing maximal oxygen uptake tests of fire fighters. It highlights the need for standardization of aerobic capacity testing in the medical evaluation of fire fighters. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Forebody/Inlet of the Joint Strike Fighter Tested at Low Speeds

NASA Technical Reports Server (NTRS)

Johns, Albert L.

1998-01-01

As part of a national cooperative effort to develop a multinational fighter aircraft, a model of a Joint Strike Fighter concept was tested in several NASA Lewis Research Center wind tunnels at low speeds over a range of headwind velocities and model attitudes. This Joint Strike Fighter concept, which is scheduled to go into production in 2005, will greatly improve the range, capability, maneuverability, and survivability of fighter aircraft, and the production program could ultimately be worth $100 billion. The test program was a team effort between Lewis and Lockheed Martin Tactical Aircraft Systems. Testing was completed in September 1997, several weeks ahead of schedule, allowing Lockheed additional time to review the results and analysis data before the next test and resulting in significant cost savings for Lockheed. Several major milestones related to dynamic and steady-state data acquisition and overall model performance were reached during this model test. Results from this program will contribute to both the concept demonstration phase and the production aircraft.

Air Force Science & Technology Issues & Opportunities Regarding High Performance Embedded Computing

DTIC Science & Technology

2009-09-23

Challenges by Domain * Air: Persistent air dominance is at risk * Increasingly effective air defenses * Proliferation of 5th generation fighters, cheap cruise missiles, and UASs * Light-speed war possibilities are terrifying * Space: Now a contested domain * Increasingly important * Increasingly vulnerable * Cyber: Cyber warfare has begun * We don’t control the battlespace * We rely on it more and more * We can’t find the enemy.

F-35 Joint Strike Fighter: Continued Oversight Needed as Program Plans to Begin Development of New Capabilities

DTIC Science & Technology

2016-04-01

3Concurrency is broadly defined as the overlap between technology development and product development or between product development and...reported extensively on the F-35 program’s cost, schedule, and performance problems. The program plans to begin increasing production rates over the...internal DOD program analyses. GAO also collected and analyzed production and supply chain performance data, and interviewed DOD, program, and

Defense Inventory: Further Analysis and Enhanced Metrics Could Improve Service Supply and Depot Operations

DTIC Science & Technology

2016-06-01

of and replace. DOD maintains weapon systems (e.g., aircraft and ships) and equipment (e.g., generators and radars) that require regular and...including helicopters, combat vehicles, air defense systems, ships, fighter and bomber aircraft , intercontinental ballistic missiles, jet aircraft ...Defense for Acquisition, Technology, and Logistics. 19In the depot maintenance context, an end item can be a weapon system, such as an aircraft , ship

Department of Defense Mobile Device Strategy. Version 2.0

DTIC Science & Technology

2012-05-01

pilots and initiatives across DoD under common objectives, ensuring that the war:fighter benefits from such activities and aligns with efforts...regularly travel from place to place; and a growing number of teleworkers are beginning to operate from locations other than their primary offices...workforce with the benefits of mobile technology. Although achieving pockets of success, this unconstrained piloting has also resulted in the lack of

Forecasting Demand for KC-135 Sorties: Deploy to Dwell Impacts

DTIC Science & Technology

2013-06-01

fighter movements from individual units are rampant (6 OSS/ OSOS , 2013). However, TACC directed missions in this category are scarce, if not non...existent (6 OSS/ OSOS , 2013). Recent TACC tasked missions that appear to support CONUS fighter movements were training related: pre-deployment preparation...and large scale exercises directed by the Joint Staff (6 OSS/ OSOS , 2013). Anecdotal evidence that AMC supports CONUS fighter movements was flawed

Filling the Fighter Gap

DTIC Science & Technology

2010-03-18

1 Filling the Fighter Gap by Major Justin DeMarco, USAF The purpose of this paper is to suggest how the Air Force can mitigate the...estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services...SUBTITLE Filling the Fighter Gap 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER

The polymorphism of dopamine receptor D4 (DRD4) and dopamine transporter (DAT) genes in the men with antisocial behaviour and mixed martial arts fighters.

PubMed

Cherepkova, Elena V; Maksimov, Vladimir N; Kushnarev, Alexandr P; Shakhmatov, Igor I; Aftanas, Lyubomir I

2017-09-12

Variable-number tandem repeat (VNTR) polymorphisms of DRD4 and DAT genes were studied in the Russian and Chechen men convicted of crimes, and two control groups comprised of the MMA fighters and a sample of general population. A group of MMA fighters included only the subjects without history of antisocial behaviour. DNA was isolated by phenol-chloroform extraction from the blood. Genotyping VNTR polymorphisms of the DRD4 and DAT genes were performed by PCR on published methods. Among those convicted of felonies and most grave crimes, carriers of DRD4 long alleles are found more frequently, similarly to the cohort of MMA fighters (lacking criminal record in both paternal lines). The 9/9 DAT genotype carriers are more frequently encountered among the habitual offenders. A frequency of the combination of the DRD4 genotype 4/7 and DAT genotype 10/10 is clearly higher among the convicts of violent crimes and the MMA fighters. One can speculate the presence of a 'controlled aggression' without a predisposition to pathological violence in the MMA fighters. Our study supports the hypothesis of genetic predisposition to different variants of extreme behaviour mediated by genetic determinants involved in the functioning of neuromediator systems including those controlling dopamine pathways.

Criteria for design of integrated flight/propulsion control systems for STOVL fighter aircraft

NASA Technical Reports Server (NTRS)

Franklin, James A.

1993-01-01

As part of NASA's program to develop technology for short takeoff and vertical landing (STOVL) fighter aircraft, control system designs have been developed for a conceptual STOVL aircraft. This aircraft is representative of the class of mixed-flow remote-lift concepts that was identified as the preferred design approach by the U.S./U.K. STOVL Joint Assessment and Ranking Team. The control system designs have been evaluated throughout the powered-lift flight envelope on the Vertical Motion Simulator (VMS) at Ames Research Center. Items assessed in the control system evaluation were: maximum control power used in transition and vertical flight, control system dynamic response associated with thrust transfer for attitude control, thrust margin in the presence of ground effect and hot-gas ingestion, and dynamic thrust response for the engine core. Effects of wind, turbulence, and ship airwake disturbances are incorporated in the evaluation. Results provide the basis for a reassessment of existing flying-qualities design criteria applied to STOVL aircraft.

Design criteria for integrated flight/propulsion control systems for STOVL fighter aircraft

NASA Technical Reports Server (NTRS)

Franklin, James A.

1993-01-01

As part of NASA's program to develop technology for short takeoff and vertical landing (STOVL) fighter aircraft, control system designs have been developed for a conceptual STOVL aircraft. This aircraft is representative of the class of mixed-flow remote-lift concepts that was identified as the preferred design approach by the US/UK STOVL Joint Assessment and Ranking Team. The control system designs have been evaluated throughout the powered-lift flight envelope on Ames Research Center's Vertical Motion Simulator. Items assessed in the control system evaluation were: maximum control power used in transition and vertical flight, control system dynamic response associated with thrust transfer for attitude control, thrust margin in the presence of ground effect and hot gas ingestion, and dynamic thrust response for the engine core. Effects of wind, turbulence, and ship airwake disturbances are incorporated in the evaluation. Results provide the basis for a reassessment of existing flying qualities design criteria applied to STOVL aircraft.

Acoustic fatigue: Overview of activities at NASA Langley

NASA Technical Reports Server (NTRS)

Mixson, John S.; Roussos, Louis A.

1987-01-01

A number of aircraft and spacecraft configurations are being considered for future development. These include high-speed turboprop aircraft, advanced vertical take-off and landing fighter aircraft, and aerospace planes for hypersonic intercontinental cruise or flight to orbit and return. Review of the acoustic environment expected for these vehicles indicates levels high enough that acoustic fatigue must be considered. Unfortunately, the sonic fatique design technology used for current aircraft may not be adequate for these future vehicles. This has resulted in renewed emphasis on acoustic fatigue research at the NASA Langley Research Center. The overall objective of the Langley program is to develop methods and information for design of aerospace vehicles that will resist acoustic fatigue. The program includes definition of the acoustic loads acting on structures due to exhaust jets of boundary layers, and subsequent determination of the stresses within the structure due to these acoustic loads. Material fatigue associated with the high frequency structural stress reversal patterns resulting from acoustic loadings is considered to be an area requiring study, but no activity is currently underway.

Static performance of vectoring/reversing non-axisymmetric nozzles

NASA Technical Reports Server (NTRS)

Willard, C. M.; Capone, F. J.; Konarski, M.; Stevens, H. L.

1977-01-01

An experimental program sponsored by the Air Force Flight Dynamics Laboratory is currently in progress to determine the internal and installed performance characteristics of five different thrust vectoring/reversing non-axisymmetric nozzle concepts for tactical fighter aircraft applications. Internal performance characteristics for the five non-axisymmetric nozzles and an advanced technology axisymmetric baseline nozzle were determined in static tests conducted in January 1977 at the NASA-Langley Research Center. The non-axisymmetric nozzle models were tested at thrust deflection angles of up to 30 degrees from horizontal at throat areas associated with both dry and afterburning power. In addition, dry power reverse thrust geometries were tested for three of the concepts. The best designs demonstrated internal performance levels essentially equivalent to the baseline axisymmetric nozzle at unvectored conditions. The best designs also gave minimum performance losses due to vectoring, and reverse thrust levels up to 50% of maximum dry power forward thrust. The installed performance characteristics will be established based on wind tunnel testing to be conducted at Arnold Engineering Development Center in the fall of 1977.

Design and analysis of a supersonic penetration/maneuvering fighter

NASA Technical Reports Server (NTRS)

Child, R. D.

1975-01-01

The design of three candidate air combat fighters which would cruise effectively at freestream Mach numbers of 1.6, 2.0, and 2.5 while maintaining good transonic maneuvering capability, is considered. These fighters were designed to deliver aerodynamically controlled dogfight missiles at the design Mach numbers. Studies performed by Rockwell International in May 1974 and guidance from NASA determined the shape and size of these missiles. The principle objective of this study is the aerodynamic design of the vehicles; however, configurations are sized to have realistic structures, mass properties, and propulsion systems. The results of this study show that air combat fighters in the 15,000 to 23,000 pound class would cruise supersonically on dry power and still maintain good transonic maneuvering performance.

External store effects on the stability of fighter and interceptor airplanes. [application to military aircraft mission requirements

NASA Technical Reports Server (NTRS)

Spearman, M. L.; Sawyer, W. C.

1974-01-01

Some criteria for external carriage of missiles for fighter aircraft intended for aerial combat missions and for fighter-interceptor missions are considered. The mission requirements discussed include the short-range fighter-interceptor, the short-range interceptor, the medium-range interceptor, and the long-range interceptor. Missiles types considered to be compatible with the various point mission designs include the short-range missile, the medium-range missile, and the long-range missile. From the study, it appears that point mission design aircraft can be arranged in such a way that the required external-store arrangement will not impair the stability of the aircraft. An extensive reference list of NASA external store research is included.

Experience with synchronous and asynchronous digital control systems

NASA Technical Reports Server (NTRS)

Regenie, V. A.; Chacon, C. V.; Lock, W. P.

1986-01-01

Flight control systems have undergone a revolution since the days of simple mechanical linkages; presently the most advanced systems are full-authority, full-time digital systems controlling unstable aircraft. With the use of advanced control systems, the aerodynamic design can incorporate features that allow greater performance and fuel savings, as can be seen on the new Airbus design and advanced tactical fighter concepts. These advanced aircraft will be and are relying on the flight control system to provide the stability and handling qualities required for safe flight and to allow the pilot to control the aircraft. Various design philosophies have been proposed and followed to investigate system architectures for these advanced flight control systems. One major area of discussion is whether a multichannel digital control system should be synchronous or asynchronous. This paper addressed the flight experience at the Dryden Flight Research Facility of NASA's Ames Research Center with both synchronous and asynchronous digital flight control systems. Four different flight control systems are evaluated against criteria such as software reliability, cost increases, and schedule delays.

Mortality and life expectancy of professional fire fighters in Hamburg, Germany: a cohort study 1950 – 2000

PubMed Central

Wagner, Norbert L; Berger, Jürgen; Flesch-Janys, Dieter; Koch, Peter; Köchel, Anja; Peschke, Michel; Ossenbach, Trude

2006-01-01

Background The healthy worker effect may hide adverse health effects in hazardous jobs, especially those where physical fitness is required. Fire fighters may serve as a good example because they sometimes are severely exposed to hazardous substances while on the other hand their physical fitness and their strong health surveillance by far exceeds that of comparable persons from the general population. Methods To study this effect a historic cohort study was conducted to assess mortality and life expectancy of professional fire fighters of the City of Hamburg, Germany. Fire departments and trade unions questioned the validity of existing studies from outside Germany because of specific differences in the professional career. No mortality study had been conducted so far in Germany and only few in Europe. Information on all active and retired fire fighters was extracted from personnel records. To assure completeness of data the cohort was restricted to all fire fighters being active on January 1, 1950 or later. Follow up of the cohort ended on June 30th 2000. Vital status was assessed by personnel records, pension fund records and the German residence registries. Mortality of fire fighters was compared to mortality of the Hamburg and German male population by means of standardized mortality ratios. Life expectancy was calculated using life table analysis. Multivariate proportional hazard models were used to assess the effect of seniority, time from first employment, and other occupational characteristics on mortality. Results The cohort consists of 4640 fire fighters accumulating 111796 person years. Vital status could be determined for 98.2% of the cohort. By the end of follow up 1052 person were deceased. Standardized Mortality Ratio (SMR) for the total cohort was 0.79 (95% CI, 0.74–0.84) compared to Hamburg reference data and 0.78 (95% CI, 0.74–0.83) compared to National German reference data. Conditional life expectancy of a 30 year old fire fighter was 45.3 years as compared to 42.9 year of a German male in normal population. Job tasks, rank status and early retirement negatively influenced mortality. For fire fighters with comparably short duration of employment the mortality advantage diminished with longer time since first employment. SMR of persons who retired early was 1.25 (95% CI, 1.13–1.60) in reference to the general German population and the SMR of 1.71 (1.18–2.50) in the multivariate regression model. Conclusion A strong healthy worker effect was observed for the cohort, which diminished with longer time since first employment for fire fighters with shorter duration of employment, as expected. The negative effects on mortality of job tasks, rank status and in particular early retirement indicate the presence of undetermined and specific risks related to occupational hazards of fire fighters. PMID:17020604

[Comparative analysis on data of nasal sinus between helicopter and(strike) fighter pilots under physical examination for change to new-type aircraft].

PubMed

Xu, Xianrong; Ma, Xiaoli; Zhang, Yang; Xiong, Wei

2012-01-01

To comparatively analyze the disease data of nasal sinus between helicopter and (strike) fighter pilots under flying qualification, and then to provide references for aeromedical support as a significant part of new logistics service union in army, The CT data of nasal sinus in 138 pilots who accepted physical examination for change to new-type aircraft, were collected included 46 cases of helicopter pilots and 92 cases of (strike)fighter pilots). The incidence of chronic sinusitis and cyst of nasal sinus were computed respectively in helicopter pilots and (strike)fighter pilots. (1) Fourteen cases suffered from chronic sinusitis (6 cases of maxillary sinusitis, 4 cases of ethmoiditis and 4 cases of maxillary sinusitis and ethmoiditis) in helicopter pilots whose incidence rate of chronic sinusitis was 30.4% (14/46). Of which, 3 cases of antracele were treated. Twelve cases suffered from chronic sinusitis (8 cases of maxillary sinusitis, 1 case of ethmoiditis, 3 cases of maxillary sinusitis and ethmoiditis) in (strike)fighter pilots whose incidence of chronic sinusitis was 13.0% (12/92). Of which, 1 case of antracele was treated. The incidence of chronic sinusitis was higher in helicopter pilots than (strike) fighters pilots (Chi2 = 6.07, P < 0.05). (2) Four cases suffered from unilateral mucosa cysts in maxillary sinus in helicopter pilots whose incidence of cyst of nasal sinus was 8.7% (4/46). Ten cases suffered from mucosa cysts in maxillary sinus (unilateral 8 cases and bilateral 2 cases) in (strike) fighters pilots whose incidence of cyst of nasal sinus was 10.87% (10/92). The difference of the incidence of cyst of nasal sinus was not statistically significant between the helicopter pilots and(strike)fighters pilots. The cysts of nasal sinus did not need treatment in 14 cases of this group data. The incidence of symptomless chronic sinusitis and cyst of nasal sinus are high in pilots. It is related with repeatedly changes of atmosphere pressure during flying. But most chronic sinusitis and cyst of nasal sinus do not need treatment. The incidence of chronic sinusitis is higher in helicopter pilots than(strike)fighter pilots. It may be related with the environment of helicopter which have unclosed cockpit and load other aircrew.

Design and Optimization of a Composite Canard Control Surface of an Advanced Fighter Aircraft under Static Loading

NASA Astrophysics Data System (ADS)

Shrivastava, Sachin; Mohite, P. M.

2015-01-01

The minimization of weight and maximization of payload is an ever challenging design procedure for air vehicles. The present study has been carried out with an objective to redesign control surface of an advanced all-metallic fighter aircraft. In this study, the structure made up of high strength aluminum, titanium and ferrous alloys has been attempted to replace by carbon fiber composite (CFC) skin, ribs and stiffeners. This study presents an approach towards development of a methodology for optimization of first-ply failure index (FI) in unidirectional fibrous laminates using Genetic-Algorithms (GA) under quasi-static loading. The GAs, by the application of its operators like reproduction, cross-over, mutation and elitist strategy, optimize the ply-orientations in laminates so as to have minimum FI of Tsai-Wu first-ply failure criterion. The GA optimization procedure has been implemented in MATLAB and interfaced with commercial software ABAQUS using python scripting. FI calculations have been carried out in ABAQUS with user material subroutine (UMAT). The GA's application gave reasonably well-optimized ply-orientations combination at a faster convergence rate. However, the final optimized sequence of ply-orientations is obtained by tweaking the sequences given by GA's based on industrial practices and experience, whenever needed. The present study of conversion of an all metallic structure to partial CFC structure has led to 12% of weight reduction. Therefore, the approach proposed here motivates designer to use CFC with a confidence.

The sharing of radiological images by professional mixed martial arts fighters on social media

PubMed Central

Joyce, Cormac W; McCarthy, Peter

2017-01-01

Background Mixed martial arts is a sport that has recently enjoyed a significant increase in popularity. This rise in popularity has catapulted many of these “cage fighters” into stardom and many regularly use social media to reach out to their fans. An interesting result of this interaction on social media is that athletes are sharing images of their radiological examinations when they sustain an injury. Purpose To review instances where mixed martial arts fighters shared images of their radiological examinations on social media and in what context they were shared. Material and Methods An Internet search was performed using the Google search engine. Search terms included “MMA,” “mixed martial arts,” “injury,” “scan,” “X-ray,” “fracture,” and “break.” Articles which discussed injuries to MMA fighters were examined and those in which the fighter themselves shared a radiological image of their injury on social media were identified. Results During our search, we identified 20 MMA fighters that had shared radiological images of their injuries on social media. There were 15 different types of injury, with a fracture of the mid-shaft of the ulna being the most common. The most popular social media platform was Twitter. The most common imaging modality X-ray (71%). The majority of injuries were sustained during competition (81%) and 35% of these fights resulted in a win for the fighter. Conclusion Professional mixed martial artists are sharing radiological images of their injuries on social media. This may be in an attempt to connect with fans and raise their profile among other fighters. PMID:28717518

Recycled Bricks: Exploring Opportunities to Reintegrate Returning American Foreign Fighters Using Existing Models

DTIC Science & Technology

2016-12-01

Fighter Travel, 6. 16 Ibid., 6–15. 17 Ibid., 13. 5 United States failed to stop Americans from going abroad to become foreign fighters, and made 32...ethnicity only possess meaning because they connect people socially.130 The different categories that American Muslims classify themselves demonstrate the...Identity.” 133 Ibid., 66. 34 An example is found in American Muslims; they identify all Americans as part of their national in-group, but when

Psychological, Social and Attitudinal Variables Associated with Infantry Combat Effectiveness and their Relation to Women

DTIC Science & Technology

1979-06-01

significantly higher.2 Also femin - inity3 as measured by the Minnesota Multiphasic Personality Inventory (MMPI) and the California Personality Inventory (CPI) L...question of women in combat. The fighters had participated in more activities, hobbies and sports than had non-fighters (19 activities as compared to...15). They tended to prefer body contact sports and had partici- pated in them longer and more frequently than had non-fighters. The activities that

A Bomber Fighter Duel (II)

DTIC Science & Technology

1949-07-25

RAND 1 RESEARCH MEMORANDUM c: . A BOMBER FIGHTER DUEL (II) David Blackwell and Max Shiffiaan HM-193 • 25 July 1949 Copy No./c^JZ. . Thi...II) David Blackwell and Max Shiffman 0. Summary. This memorandum completes the study’of the fighteir- bomber duel described in RM-l65i» The... duel is one in which a fighter fires a single rocket burst at a bomber, which has limited ammunition, and defends itself by intermittent firing. It

Medical evaluation of fire fighters: How fit are they for duty?

PubMed

Davis, P O; Biersner, R J; Barnard, R J; Schamadan, J

1982-08-01

Aside from the obvious dangers to life and limb associated with the job, fire fighting subjects the body to environmental and physical stressors that can adversely affect various systems. In fact, the effects of these stressors on the cardiovascular system have made coronary heart disease a greater killer among fire fighters than among other occupational groups. The approach to medical evaluation of fire fighters presented here is based on an appreciation of these stressors.

Fire fighting and its influence on the body.

PubMed

Rossi, René

2003-08-15

Working conditions for fire fighters can be described according to the environment temperature and the incident radiant heat flux. Measurements for this study in buildings for fire fighting training have shown that fire fighters are typically exposed to radiant heat fluxes of between 5 and 10 kWm(-2) during this kind of exercise. The heat load can nevertheless be much higher. In one case, 42 kWm(-2) was measured. The temperatures reached between 100 and 190 degrees C at 1 m above ground, going up to 278 degrees C in one case. Human trials have been performed with 17 fire fighters. After exercises (about 15 min) in a heated room, the mean core temperature of the fire fighters rose by 0.6 degrees C with a surrounding temperature of 31 degrees C and 1.0 degrees C with 38 degrees C. The sweat production varied from 0.7 to 2.1 lh(-1); 16% to 45% of sweat remained in the clothing layers. During the exercises in the training buildings, a mean of 48 degrees C has been measured between fire fighters' clothing and workwear. These conditions lead to an increase of the relative humidity in all the jackets up to 100%. When the fire fighters came out of the fire, the humidity remained at this level in the PVC coated jackets while it was in some cases strongly reduced in breathable jackets.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antolak, Arlyn J.

Particle accelerators play a key role in a broad set of defense and security applications including war-fighter and asset protection, cargo inspection, nonproliferation, materials characterization and stockpile stewardship. Accelerators can replace the high activity radioactive sources that pose a security threat for developing a radiological dispersal device and be used to produce isotopes for medical, industrial, and re-search purposes. Lastly, we present an overview of current and emerging accelerator technologies relevant to addressing the needs of defense and security.

TALON: a universal unmanned ground vehicle platform, enabling the mission to be the focus

NASA Astrophysics Data System (ADS)

Wells, Peter; Deguire, Dan

2005-05-01

Foster-Miller's unmanned ground vehicle, TALON, was originally developed under DARPA's Tactical Mobile Robotics (TMR) program. TALON has evolved over the years and has proven to be a robust, mobile, universal platform. As a result of the advances made in the evolution of TALON, new and far-reaching opportunities have been realized for unmanned ground vehicles. In recent conflicts such as in Afghanistan and Iraq, unmanned systems have played an important role and have extended the reach and capabilities of the War fighter. Technological advances have transformed unmanned vehicles in to useful tools and in some cases are used in lieu of sending in a soldier. Unmanned ground vehicles have seen recent and persistent success, as shown in theater, in the explosive ordinance disposal (EOD) and improvised ordinance disposal (IED) missions. Foster-Miller's TALON has experienced over ten thousand EOD and IED missions in Iraq alone. The success of the unmanned system has resulted in the doctrine "Send the robot in first". Foster-Miller has taken the role of the unmanned vehicle in yet another direction. Foster-Miller has transformed the TALON from a "practical" to "tactical" system. Through the combined efforts of Foster-Miller and the US Army, TALON has been involved in a weaponization program. To date, Foster-Miller has outfitted the TALON with 11 systems. As one can see, the unmanned ground vehicle is much more than a mobility platform.

Psychological distress and alcohol use among fire fighters.

PubMed

Boxer, P A; Wild, D

1993-04-01

Few studies have investigated stressors to which fire fighters are subjected and the potential psychological consequences. One hundred and forty-five fire fighters were studied to enumerate potential occupational stressors, assess psychological distress and problems with alcohol use, and determine whether a relationship exists between these measures and self-reported stressors. Hearing that children are in a burning building was the highest ranked stressor. According to three self-report instruments, between 33 and 41% of the fire fighters were experiencing significant psychological distress, and 29% had possible or probable problems with alcohol use. These figures are significantly higher than would be expected in a typical community or working population. In a logistic regression analysis, no relationship was found between measures of psychological distress and alcohol use and the 10 most highly ranked work stressors.

The Caliphates Global Workforce: An Inside Look at the Islamic States Foreign Fighter Paper Trail

DTIC Science & Technology

2016-04-01

The Caliphate’s Global Workforce: An Inside Look at the Islamic State’s Foreign Fighter Paper Trail Brian Dodwell Daniel Milton Don Rassler The...Caliphate’s Global Workforce: An Inside Look at the Islamic State’s Foreign Fighter Paper Trail Brian Dodwell Daniel Milton Don Rassler Combating...Terrorism Center at West Point April 2016 Cover Photo: Image taken from the Islamic State’s Dabiq magazine United States Military Academy www.ctc.usma.edu

High Energy Laser on the Joint Strike Fighter: A Reality in 2025?

DTIC Science & Technology

2007-02-26

10 October 2006. 19. Siegman , A.E., Nemes, G., Serna, J. “How to (Maybe) Measure Laser Beam Quality,” in DPSS (Diode Pumped Solid State) Lasers ...AIR WAR COLLEGE AIR UNIVERSITY HIGH ENERGY LASER ON THE JOINT STRIKE FIGHTER A REALITY IN 2025? by Jeffrey A. Hausmann, Lt Col, USAF A...00-00-2007 to 00-00-2007 4. TITLE AND SUBTITLE High Energy Laser on the Joint Strike Fighter a Reality in 2025? 5a. CONTRACT NUMBER 5b. GRANT

The Debate is Over: Close Air Support in Korea and Vietnam

DTIC Science & Technology

2011-05-03

F4U Corsair became Marine aviation’s plane of choice. Early models of the Corsair were formidable fighter aircraft best suited for the air...superiority role. By 1944, the Marine Corps made a deliberate effort to transform the Corsair from a fighter to a multi-role fighter- bomber. As such, the F4U...installation of a ten-channel radio facilitated better communications with ground forces. The upgraded Corsair was such an effective ground attack platform

Modeling aerosol emissions from the combustion of composite materials

NASA Technical Reports Server (NTRS)

Roop, J. A.; Caldwell, D. J.; Kuhlmann, K. J.

1994-01-01

The use of advanced composite materials (ACM) in the B-2 bomber, composite armored vehicle, and F-22 advanced tactical fighter has rekindled interest concerning the health risk of burned or burning ACM. The objective of this work was to determine smoke production from burning ACM and its toxicity. A commercial version of the UPITT II combustion toxicity method developed at the University of Pittsburgh, and subsequently refined through a US Army-funded basic research project, was used to established controlled combustion conditions which were selected to evaluate real-world exposure scenarios. Production and yield of toxic species varied with the combustion conditions. Previous work with this method showed that the combustion conditions directly influenced the toxicity of the decomposition products from a variety of materials.

Thrust Vectoring for Advanced Fighter Aircraft - High Angle of Attack Intake Investigations -

DTIC Science & Technology

2001-06-01

these losses. plane) a rake for the measurement of swirl and pressure recovery has been used. The five-hole probes and the pitot Whereas the total...true for the two be recognized in fig. 4,3.1. There exist 8 rake arms with 7 pitot intake parameters mean swirl and dynamic distortion. In order probes...recognized that at the low intake mass this rake is measured with the help of 16 rake arms with 5 pitot flowT the pressure recovery up to an angle of

The Use of Exergy and Decomposition Techniques in the Development of Generic Analysis, and Optimization Methodologies Applicable to the Synthesis/Design of Aircraft/Aerospace Systems

DTIC Science & Technology

2006-04-21

C. M., and Prendergast, J. P., 2002, "Thermial Analysis of Hypersonic Inlet Flow with Exergy -Based Design Methods," International Journal of Applied...parametric study of the PS and its components is first presented in order to show the type of detailed information on internal system losses which an exergy ...Thermoeconomic Isolation Applied to the Optimal Synthesis/Design of an Advanced Fighter Aircraft System," International Journal of Thermodynamics, ICAT

Review of Relocation of the System Program Office and Logistics Support for the F-117A Stealth Fighter

DTIC Science & Technology

1998-04-10

LMSW. Cost of Repair Number Avoided Nomenclature New Part Cost Repaired Cost Wing platypus panel $60,100 $4,500 10 $ 556,000 Lower rear door panel...72,200 7,000 48 3,129,600 Rear door trailing 76,000 6,000 2 140,000 edge panel Inboard platypus panel 56,000 4,200 46 2,410,400 Outboard platypus panel...Composites Shop’s contribution to resolving the problem consisted of the redesign of the wing and inboard and outboard platypus panels. The Advanced

NAS (Numerical Aerodynamic Simulation Program) technical summaries, March 1989 - February 1990

NASA Technical Reports Server (NTRS)

1990-01-01

Given here are selected scientific results from the Numerical Aerodynamic Simulation (NAS) Program's third year of operation. During this year, the scientific community was given access to a Cray-2 and a Cray Y-MP supercomputer. Topics covered include flow field analysis of fighter wing configurations, large-scale ocean modeling, the Space Shuttle flow field, advanced computational fluid dynamics (CFD) codes for rotary-wing airloads and performance prediction, turbulence modeling of separated flows, airloads and acoustics of rotorcraft, vortex-induced nonlinearities on submarines, and standing oblique detonation waves.

The effect of smoke inhalation on lung function and airway responsiveness in wildland fire fighters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, D.; Tager, I.B.; Balmes, J.R.

1992-12-01

The current study was undertaken to evaluate the effect of smoke on forced expiratory volumes and airway responsiveness in wildland fire fighters during a season of active fire fighting. Sixty-three seasonal and full-time wildland fire fighters from five U.S. Department of Agriculture Forest Service (USDAFS) Hotshot crews in Northern California and Montana completed questionnaires, spirometry, and methacholine challenge testing before and after an active season of fire fighting in 1989. There were significant mean individual declines of 0.09, 0.15, and 0.44 L/s in postseason values of FVC, FEV1, and FEF25-75, respectively, compared with preseason values. There were no consistent significantmore » relationships between mean individual declines of the spirometric parameters and the covariates: sex, smoking history, history of asthma or allergies, years as a fire fighter, upper/lower respiratory symptoms, or membership in a particular Hotshot crew. There was a statistically significant increase in airway responsiveness when comparing preseason methacholine dose-response slopes (DRS) with postseason dose-response slopes (p = 0.02). The increase in airway responsiveness appeared to be greatest in fire fighters with a history of lower respiratory symptoms or asthma, but it was not related to smoking history. These data suggest that wildland fire fighting is associated with decreases in lung function and increases in airway responsiveness independent of a history of cigarette smoking. Our findings are consistent with the results of previous studies of municipal fire fighters.« less

Research on tactical information display technology for interactive virtual cockpit

NASA Astrophysics Data System (ADS)

Sun, Zhongyun; Tian, Tao; Su, Feng

2018-04-01

Based on a fact that traditional tactical information display technology suffers from disadvantages of a large number of data to be transferred and low plotting efficiency in an interactive virtual cockpit, a GID protocol-based simulation has been designed. This method dissolves complex tactical information screens into basic plotting units. The indication of plotting units is controlled via the plotting commands, which solves the incompatibility between the tactical information display in traditional simulation and the desktop-based virtual simulation training system. Having been used in desktop systems for helicopters, fighters, and transporters, this method proves to be scientific and reasonable in design and simple and efficient in usage, which exerts a significant value in establishing aviation equipment technology support training products.

Cost Efficiency Implications of International Cooperation (Implications de rentabilite de la cooperation internationale)

DTIC Science & Technology

2015-04-01

CZECH REPUBLIC Col. Zdenek Petras Centre for Security and Military Strategic Studies University of Defence Kounicova 156/65 66210 Brno Email...military systems in order to reduce costs. Nine Nations are cooperating with Lockheed Martin to develop and produce the next generation fighter jets...is led by the technologically first-tier Nation, the US, where Lockheed Martin is the managing authority on the supply side and the US F-35 Joint

Naval War College Review. Volume 66, Number 1, Winter 2013

DTIC Science & Technology

2013-01-01

planes to run experiments. The ships themselves had some new technology: four-channel very-high- frequency (VHF) radios for the fighter-direction teams...1 11 /6/12 8:31 AM Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is estimated to...SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S) 11 . SPONSOR/MONITOR’S REPORT NUMBER(S) 12. DISTRIBUTION/AVAILABILITY

Offsets in Weapon System Sales: A Case Study of the Korean Fighter Program

DTIC Science & Technology

1992-09-01

technology transfer and countertrade (82:3-4). Detailed definitions of these terms will be inserted in the text where appropriate. In addition, Appendix A...more countries realize their leverage in competitive world markets, countertrade and offset requirements have become part and parcel of international...business" (81:74). The number of countries that require some form of countertrade has risen from about fifteen in the early 1970’s (52:72), to twenty

The Need for a Permanent Gun System On the F-35 Joint Strike Fighter

DTIC Science & Technology

2007-04-01

subject material . Finally, I would like to thank my wife, Niki, for her love, support and understanding. iv Abstract Historically, the United...concept that showed the most promise involved building upon the Gatlin gun technology of the nineteenth century.20 By using a multiple barrel design...one form or another, has been present since military pilots first took to the air. From simply using their own handguns to shoot at enemy aircraft

Installation Restoration Program. Preliminary Assessment: 183rd Tactical Fighter Group, Illinois Air National Guard, Capital Airport, Springfield, Illinois

DTIC Science & Technology

1990-05-01

11140 Rockville Pike Rockville, Maryland 20852 Contract No. DLA 900-82-C-4426 Completed by Science & Technology, Inc. 704 South Illinois Avenue Suite C... Environments . .......... 111-19 IV. SITE EVALUATION...................v-i *A. Activity Review ................. v-i B. Disposal/Spill Site Identification...approximately 120 feet north of a small pond and creek located on the south side of the airport on airport property. The Base conducted operations at

Modified Dynamic Inversion to Control Large Flexible Aircraft: What's Going On?

NASA Technical Reports Server (NTRS)

Gregory, Irene M.

1999-01-01

High performance aircraft of the future will be designed lighter, more maneuverable, and operate over an ever expanding flight envelope. One of the largest differences from the flight control perspective between current and future advanced aircraft is elasticity. Over the last decade, dynamic inversion methodology has gained considerable popularity in application to highly maneuverable fighter aircraft, which were treated as rigid vehicles. This paper explores dynamic inversion application to an advanced highly flexible aircraft. An initial application has been made to a large flexible supersonic aircraft. In the course of controller design for this advanced vehicle, modifications were made to the standard dynamic inversion methodology. The results of this application were deemed rather promising. An analytical study has been undertaken to better understand the nature of the made modifications and to determine its general applicability. This paper presents the results of this initial analytical look at the modifications to dynamic inversion to control large flexible aircraft.

EC95-42939-8

NASA Image and Video Library

1995-02-02

Photographed outside their hangar at the Dryden Flight Research Center, Edwards, California, part of Dryden's F-16 fleet is, left to right; an F-16A, the F-16XL no. 1, and the F-16 AFTI. The F-16A (NASA 516), the only civil registered F-16 in existence, was transferred to Dryden from Langley, and was primarily used in engine tests and for parts. It was subsequently transfered from Dryden. The single-seat F-16XL no. 1 (NASA 849) was most recently used in the Cranked-Arrow Wing Aerodynamics Project (CAWAP) to test boundary layer pressures and distribution. Previously it had been used in a program to investigate the characteristics of sonic booms for NASA's High Speed Research Program. Data from the program will be used in the development of a high speed civilian transport. During the series of sonic boom research flights, the F-16XL was used to probe the shock waves being generated by a NASA SR-71 and record their shape and intensity. The Advanced Fighter Technology Integration (AFTI) F-16 was used to develop and demonstrate technologies to improve navigation and a pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. Earlier research in the joint NASA-Air Force AFTI F-16 program demonstrated voice actuated controls, helmet-mounted sighting and integration of forward-mounted canards with the standard flight control system to achieve uncoupled flight.

An analytical approach to air defense: cost, effectiveness and SWOT analysis of employing fighter aircraft and modern SAM systems

NASA Astrophysics Data System (ADS)

Kus, Orcun; Kocaman, Ibrahim; Topcu, Yucel; Karaca, Volkan

2012-05-01

The problem of defending a specific airspace is among the main issues a military commander to solve. Proper protection of own airspace is crucial for mission success at the battlefield. The military doctrines of most world armed forces involve two main options of defending the airspace. One of them is utilizing formations of fighter aircraft, which is a flexible choice. The second option is deploying modern SAM (Surface to Air Missile) systems, which is more expansive. On the other hand the decision makers are to cope with miscellaneous restrictions such as the budgeting problems. This study defines air defense concept according to modern air warfare doctrine. It considers an air defense scenario over an arbitrary airspace and compares the performance and cost-effectiveness of employing fighter aircraft and SAM systems. It also presents SWOT (Strenghts - Weakness - Opportunities - Threats) analyses of air defense by fighter aircraft and by modern SAMs and tries to point out whichever option is better. We conclude that deploying SAMs has important advantages over using fighter aircraft by means of interception capacity within a given time period and is cost-effective.

Patent foramen ovale and asymptomatic brain lesions in military fighter pilots.

PubMed

Kang, Kyung Wook; Kim, Joon-Tae; Choi, Won-Ho; Park, Won-Ju; Shin, Young Ho; Choi, Kang-Ho

2014-10-01

Previous studies have reported higher incidence of white matter lesions (WMLs) in military pilots. The anti-gravity straining maneuver, which fighter military pilots perform numerously during a flight is identical to the valsalva maneuver. We sought to investigate the prevalence of right-to-left shunt (RLS) associated with WMLs in military pilots. A prospective study was performed involving military pilots who visited the Airomedical Center. The pilots underwent brain magnetic resonance imaging (MRI) scan and transcranial Doppler (TCD) with intravenous injection of agitated saline solution for the detection of RLS. Periventricular WMLs (PVWMLs) on MRI were graded using Fazeka's scale, and deep WMLs (DWMLs) were graded using Scheltens's scale. This study included 81 military pilots. RLS on TCD was observed less frequently in non-fighter pilots than in fighter pilots (35.5% vs. 64.5%, p=0.011). Fighter pilot was an independently associated factor with RLS on the TCD. DWMLs were independently associated with RLSs through a patent foramen ovale (PFO) (OR 3.507, 95% CI 1.223-10.055, p=0.02). The results suggest that DWMLs in military pilots may significantly be associated with RLS via PFO. Additional investigations are warranted. Copyright © 2014 Elsevier B.V. All rights reserved.

Former WWII Fighter Pilot Finds New Home Near Family

MedlinePlus

... Navigation Bar Home Current Issue Past Issues Feature: Senior Living Former WWII Fighter Pilot Finds New Home ... in Kalispell, Mont. Advice On a Move to Senior Living: Investigate your new surroundings. Talk to those ...

Flow field over the wing of a delta-wing fighter model with vortex control devices at Mach 0.6 to 1.2

NASA Technical Reports Server (NTRS)

Bare, E. Ann; Reubush, David E.; Haddad, Raymond C.

1992-01-01

As part of a cooperative research program between NASA, McDonnell Douglas Corporation, and Wright Research and Development Center, a flow field investigation was conducted on a 7.52 percent scale windtunnel model of an advanced fighter aircraft design. The investigation was conducted in the Langley 16 ft Transonic Tunnel at Mach numbers of 0.6, 0.9, and 1.2. Angle of attack was varied from -4 degrees to 30 degrees and the model was tested at angles of sideslip of 0, 5, and -5 degrees. Data for the over the wing flow field were obtained at four axial survey stations by the use of six 5 hole conical probes mounted on a survey mechanism. The wing leading edge primary vortex exerted the greatest influence in terms of total pressure loss on the over the wing flow field in the area surveyed. A number of vortex control devices were also investigated. They included two different apex flaps, wing leading edge vortex flaps, and small large wing fences. The vortex flap and both apex flaps were beneficial in controlling the wing leading edge primary vortex.

Multi-Level Scenario Module 1: 7th Division

DTIC Science & Technology

2009-03-01

MQ1B Recon Sq 1x RC135S Recon Sq 5x RC135VW Cythera Paros Shaw Peterson Fighter Sq 24x F16CD BLK-50 Fighter Sq 24x F15E Fighter Sq 24x A/0A10A Airlift Sq...Mountain Home Amphibious Assault Ship, Multipurpose (LHD) Amphibious Transport Dock (LPD) Dock Landing Ship ( LSD ) Guided Missile Cruiser (CG...Destroyer (DDG) x2 Submarine, Nuclear Powered (SSN) x 6 Guided Missile Submarine, Nuclear Powered (SSGN) Cythera Paros Shaw Peterson Guided

Overwhelming Force, Indecisive Victory: The German Invasion of Yugoslavia, 1941

DTIC Science & Technology

1993-05-13

It was a system of large units that depended primarily on animal draft power for transportation that resulted in low march speed and lack of...STUBOL* 12 3D BOMBER REGT SKOPLJE* 13 63D BOMBER GROUP PZTROVAC 30 D017 13 64TH BOMBER GROUP PSTROVAC 30 DOl0 14 5TH FIGHTER RIGT NIS* 15 35TH...FIGHTER GROUP KOSANCIC 15 HAWKER FURY 16 36TH FIGHTER GROUP REZANOVACKA KOSA 15 HAWKER FURY 17 4TH BOMBER AIR BDE LJUBIC* 18 1ST BOMBER RIGT NOVI SAD* 19

The usage of phase change materials in fire fighter protective clothing: its effect on thermal protection

NASA Astrophysics Data System (ADS)

Zhao, Mengmeng

2017-12-01

The thermal protective performance of the fire fighter protective clothing is of vital importance for fire fighters. In the study fabrics treated by phase change materials (PCMs) were applied in the multi-layered fabrics of the fire fighter protective clothing ensemble. The PCM fabrics were placed at the different layers of the clothing and their thermal protective performance were measured by a TPP tester. Results show that with the application of the PCM fabrics the thermal protection of the multi-layered fabrics was greatly increased. The time to reach a second degree burn was largely reduced. The location of the PCM fabrics at the different layers did not affect much on the thermal protective performance. The higher amount of the PCM adds on, the higher thermal protection was brought. The fabrics with PCMs of a higher melting temperature could contribute to higher thermal protection.

Longitudinal performance of plasma neurofilament light and tau in professional fighters: The Professional Fighters Brain Health Study.

PubMed

Bernick, Charles; Zetterberg, Henrik; Shan, Guogen; Banks, Sarah; Blennow, Kaj

2018-04-02

The objective of this study is to evaluate longitudinal change in plasma neurofilament light (NF-L) and tau levels in relationship to clinical and radiological measures in professional fighters. Participants (active and retired professional fighters and control group) underwent annual blood sampling, 3 Tesla MRI brain imaging, computerized cognitive testing, and assessment of exposure to head trauma. Plasma tau and NF-L concentrations were measured using Simoa assays. Multiple linear regression models were used to compare the difference across groups in regard to baseline measurements, while mixed linear models was used for the longitudinal data with multiple measurements for each participant. Plasma samples were available on 471 participants. Baseline NF-L measures differed across groups (F_3,393=6.99, p=0.0001), with the active boxers having the highest levels. Higher NF-L levels at baseline were correlated with lower baseline MRI regional volumes and lower cognitive scores. The number of sparring rounds completed by the active fighters was correlated with NF-L (95% CI 0.0116-0.4053, p=0.0381), but not tau, levels. Among 126 subjects having multiple yearly samples, there was a significant difference in average yearly percentage change in tau across groups (F_3,83=3.87, p=0.0121).). We conclude that plasma NF-L and tau behave differently in a group of active and retired fighters; NF-L better reflects acute exposure whereas the role of plasma tau levels in signifying chronic change in brain structure over time requires further study.

AFTI/F-16 Spin chute close-up

NASA Technical Reports Server (NTRS)

1982-01-01

A close-up photo of the spin chute mounted on the rear fuselage of the AFTI F-16, a safety device designed to prevent the loss of aircraft in spin conditions. Under some circumstances, pilots cannot recover from spins using normal controls. It these instances, the spin chute is deployed, thus 'breaking' the spin and enabling the pilot to recover. The spin chute is held in a metal cylinder attached to the AFTI F-16 by four tubes, a structure strong enough to withstand the shock of the spin chute opening. Unlike the air probe in the last photo, spin chutes are not standard equipment on research or prototype aircraft but are commonly attached expressly for actual spin tests. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

Focused Lens on Unmanned Aerial Systems: An Evaluation of Department of Defense’s Unmanned Aerial Vision 2011

DTIC Science & Technology

2014-06-13

Break Free of Regulations.” 69Barbara Opall -Rome, “ Israel Tackles The Last Frontier Of UAS Technology: Israel Moves Closer Toward Flying UASs In...with the new F-35 Joint Strike Fighter once it comes online, or with helicopters aboard the Littoral Combat Ship. Unmanned mine hunters could operate...Office, 2002. ———. Unmanned Aircraft Systems Roadmap 2005-2030. Washington, DC: Government Publishing Office, 2005. Opall -Rome, Barbra. “Israel

Robust Recognition of Loud and Lombard speech in the Fighter Cockpit Environment

DTIC Science & Technology

1988-08-01

the latter as inter-speaker variability. According to Zue [Z85j, inter-speaker variabilities can be attributed to sociolinguistic background, dialect...34 Journal of the Acoustical Society of America , Vol 50, 1971. [At74I B. S. Atal, "Linear prediction for speaker identification," Journal of the Acoustical...Society of America , Vol 55, 1974. [B771 B. Beek, E. P. Neuberg, and D. C. Hodge, "An Assessment of the Technology of Automatic Speech Recognition for

International Aerospace and Ground Conference on Lightning and Static Electricity (8th): Lightning Technology Roundup, held at Fort Worth, Texas on 21-23 June 1983.

DTIC Science & Technology

1983-06-01

fighter aircraft. The entire test bed is from testing of a representative digital supported above the ground plane by non - control system(s)l e.g... control and Increased systems Integration a. Raw data must be collected and Introduce new requirements for protection, experimental setups and An accurate...presented, several possible solutions to the grounding prob! - are suggested. All rely on establishing initial ground contact through a controlled non -zero

Overview of Accelerator Applications for Security and Defense

DOE PAGES

Antolak, Arlyn J.

2015-01-01

Particle accelerators play a key role in a broad set of defense and security applications including war-fighter and asset protection, cargo inspection, nonproliferation, materials characterization and stockpile stewardship. Accelerators can replace the high activity radioactive sources that pose a security threat for developing a radiological dispersal device and be used to produce isotopes for medical, industrial, and re-search purposes. Lastly, we present an overview of current and emerging accelerator technologies relevant to addressing the needs of defense and security.

Any Time, Every Place: The Networked Societies of War Fighters in a Battlespace of Flows

DTIC Science & Technology

2015-10-01

Power Journal Blair Notes 1. William H. McRaven, Spec Ops: Case Studies in Special Operations Warfare: Theory and Practice (New York: Presidio Press...and Dr. William Thiesen and others, various interviews by the author, US Coast Guard Historian’s Office, Spring 2013. 14. James C. Scott, Seeing... Cullen , “The MQ-9 Reaper Remotely Piloted Aircraft: Humans and Machines in Ac- tion” (PhD diss., Massachusetts Institute of Technology, 2011), 129, 216

An Evaluation of the Effective Block Approach Using P-3C and F-111 Crack Growth Data

DTIC Science & Technology

2008-09-01

the end of 2006 where his research interests included, modelling of fatigue crack growth, infrared NDT technologies and fibre optic corrosion...2006). It was claimed that the growth of these cracks in structures made of 7050 aluminium alloy could not be adequately predicted using classical...the crack growth behaviour of 7050 aluminium alloy subjected to the service load of the F/A-18 fighter planes. To make the matter worse, the

The Costs and Benefits of Pre-Planned Product Improvements for the Consolidated Automated Support System (CASS)

DTIC Science & Technology

1993-11-01

ground missions and must operate effectively in both domains . Figure A-3 shows a block diagram of a modem fighter radar3 system . Technologies that are...I AUTOMATED SUPPORT SYSTEM (CASS) I i Daniel B. Levine Waynard C. Devers, Project Leader Bernard L. Retterer Howard S. Savage Clayton V. Stewart...Improvements for theI Consolidated Automated Support System (CASS) MDA 903 89C 0003 6. AUThiOR( T-B7-1095 Daniel B. Levine, Waynard C. Devers

Experience with synchronous and asynchronous digital control systems. [for flight

NASA Technical Reports Server (NTRS)

Regenie, Victoria A.; Chacon, Claude V.; Lock, Wilton P.

1986-01-01

Flight control systems have undergone a revolution since the days of simple mechanical linkages; presently the most advanced systems are full-authority, full-time digital systems controlling unstable aircraft. With the use of advanced control systems, the aerodynamic design can incorporate features that allow greater performance and fuel savings, as can be seen on the new Airbus design and advanced tactical fighter concepts. These advanced aircraft will be and are relying on the flight control system to provide the stability and handling qualities required for safe flight and to allow the pilot to control the aircraft. Various design philosophies have been proposed and followed to investigate system architectures for these advanced flight control systems. One major area of discussion is whether a multichannel digital control system should be synchronous or asynchronous. This paper addressed the flight experience at the Dryden Flight Research Facility of NASA's Ames Research Center with both synchronous and asynchronous digital flight control systems. Four different flight control systems are evaluated against criteria such as software reliability, cost increases, and schedule delays.

Professional fighters brain health study: rationale and methods.

PubMed

Bernick, Charles; Banks, Sarah; Phillips, Michael; Lowe, Mark; Shin, Wanyong; Obuchowski, Nancy; Jones, Stephen; Modic, Michael

2013-07-15

Repetitive head trauma is a risk factor for Alzheimer's disease and is the primary cause of chronic traumatic encephalopathy. However, little is known about the natural history of, and risk factors for, chronic traumatic encephalopathy or about means of early detection and intervention. The Professional Fighters Brain Health Study is a longitudinal study of active professional fighters (boxers and mixed martial artists), retired professional fighters, and controls matched for age and level of education. The main objective of the Professional Fighters Brain Health Study is to determine the relationships between measures of head trauma exposure and other potential modifiers and changes in brain imaging and neurological and behavioral function over time. The study is designed to extend over 5 years, and we anticipate enrollment of more than 400 boxers and mixed martial artists. Participants will undergo annual evaluations that include 3-tesla magnetic resonance imaging scanning, computerized cognitive assessments, speech analysis, surveys of mood and impulsivity, and blood sampling for genotyping and exploratory biomarker studies. Statistical models will be developed and validated to predict early and progressive changes in brain structure and function. A composite fight exposure index, developed as a summary measure of cumulative traumatic exposure, shows promise as a predictor of brain volumes and cognitive function.

Effects of fire fighter protective ensembles on mobility and performance.

PubMed

Coca, Aitor; Williams, W Jon; Roberge, Raymond J; Powell, Jeffrey B

2010-07-01

Many studies have shown that fire fighter turnout gear and equipment may restrict mobility. The restriction of movement is usually due to a decrease in range of motion (ROM). It is important to know how much the decrease in ROM affects performance. The aim of this study was to determine the effects of fire fighter protective ensembles on mobility and performance by measuring static and dynamic range of motion (ROM) and job-related tasks. Eight healthy adults (5 males, 3 females), aged 20-40 years, participated in this study. The study consisted of measuring a battery of motions and fire fighter specific tasks while wearing a standard fire fighter ensemble (SE) or regular light clothing (baseline or BL). Several BL ROM tests were significantly (p < 0.05) different from the SE test, including a decrease in shoulder flexion, cervical rotation and flexion, trunk lateral flexion, and stand and reach. There was a significant decrease in time from SE to baseline performing the one-arm search task and object lift. These overall findings support the need for a comprehensive ergonomic evaluation of protective clothing systems to ascertain human factors issues. The development of a Standard Ergonomics Test Practice for further use in laboratories that conduct personal protective systems evaluations using human test subjects is recommended. Published by Elsevier Ltd.

X-31 Wing Storage for Shipping

NASA Image and Video Library

1995-05-18

The right wing of the X-31 Enhanced Fighter Maneuverability Technology Demonstrator Aircraft is seen here being put into a shipping container May 18, 1995, at NASA's Dryden Flight Research Center, Edwards, California, by U.S. and German members of the program. To fit inside an Air Force Reserve C-5 transport, which was used to ferry the X-31 to Europe on May 22, 1995, the right wing had to be removed. Manching, Germany, was used as a staging base to prepare the aircraft for participation in the Paris Air Show. At the air show on June 11 through the 18th, the X-31 demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems to provide controlled flight at very high angles of attack. The aircraft arrived back at Edwards in an Air Force Reserve C-5 on June 25, 1995, and off loaded at Dryden the 27th. The X-31 aircraft was developed jointly by Rockwell International's North American Aircraft Division (now part of Boeing) and Daimler-Benz Aerospace (formerly Messerschmitt-Bolkow-Blohm), under sponsorship by the U.S. Department of Defense and the German Federal Ministry of Defense.

Editorial on Future Jet Technologies

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2014-08-01

Advanced jet engines do not operate in an application vacuum. Their optimal use in advanced military applications drives much of their basic innovative research and development, especially when new needs arise in the rapidly changing domains of stealth-agile, fighter aircraft and tailless-stealth, Jet-Steered, Unmanned Air Vehicles (JS-UAV). For these reasons we periodically update this Journal with new trends that affect, and sometimes control, research and development of future jet-engines. One relevant example is the recently unmasked RQ-180 stealth-tailless drone, which is an improved version of the smaller, RQ-170 captured by Iran. Most important, with the new X-47B/C tailless-stealth JS-UAV, it is to dominate future uses of fuel-efficient jet-engines, especially for operating in dusty environments. The RQ-180 has been secretly designed and funded since 2008. It is based on a classified, 1986, parent Israeli Patents 78402, which protect hundreds design and testing trade secrets taken from 1986 to 1997 by the United States Government (USG) via classified contracts with USG-Contractors Boeing, Lockheed, General Dynamics and General Electric, as revealed by a December 6, 2013 Aviation Week [1-3] and U.S. Court of Appeals for the Federal Circuit, Case 2014-5028, Docket 12 [4]. The new RQ-180 design explains the recent U.S. Air Force ISR shift away from "permissive" environments - such as Iraq and Afghanistan, where non-stealthy Global Hawk and General Atomics' Reaper operate - toward new missions in highly "contested" or strongly "denied" enemy airspaces.

Wind Tunnel Results from a Nozzle Afterbody Test of a 0.2-Scale Fighter Aircraft in the Mach Number Regime of 0.6 to 1.5. Volume 1. Test Technique Evaluation

DTIC Science & Technology

1979-04-01

edge up. The influence of the aircraft on the static pressure reading from the pitot boom was determined with a scaled version of the pltot probe...stabilization before advancing to the next port. Jet exhaust simulation flow was monitored by internal duct pressure and temperature rakes . Standard...Mach numbers 0.6 and 1.2, Figs. 24 and 25. 13 AE DC-TR-79-10 At supersonic speeds, changes in the afterbody and nozzle axial loads (Fig. 22b) are

Design of a Low Cost Short Takeoff-vertical Landing Export Fighter/attack Aircraft

NASA Technical Reports Server (NTRS)

Belcher, Anne; Bodeker, Dan, III; Miu, Steve; Petro, Laura; Senf, Cary Taylor; Woeltjen, Donald

1990-01-01

The design of a supersonic short takeoff and vertical landing (STOVL) aircraft is presented that is suitable for export. An advanced four poster, low bypass turbofan engine is to be used for propulsion. Preliminary aerodynamic analysis is presented covering a determination of CD versus CL, CD versus Mach number, as well as best cruise Mach number and altitude. Component locations are presented and center of gravity determined. Cost minimization is achieved through the use of developed subsystems and standard fabrication techniques using nonexotic materials. Conclusions regarding the viability of the STOVL design are presented.

Control law parameterization for an aeroelastic wind-tunnel model equipped with an active roll control system and comparison with experiment

NASA Technical Reports Server (NTRS)

Perry, Boyd, III; Dunn, H. J.; Sandford, Maynard C.

1988-01-01

Nominal roll control laws were designed, implemented, and tested on an aeroelastically-scaled free-to-roll wind-tunnel model of an advanced fighter configuration. The tests were performed in the NASA Langley Transonic Dynamics Tunnel. A parametric study of the nominal roll control system was conducted. This parametric study determined possible control system gain variations which yielded identical closed-loop stability (roll mode pole location) and identical roll response but different maximum control-surface deflections. Comparison of analytical predictions with wind-tunnel results was generally very good.

Practical application of AMLCDs for tactical fighter aircraft

NASA Astrophysics Data System (ADS)

McClaskey, Paul; Craddock, Roger

1995-06-01

Development and testing of an AMLCD-display to replace a dichroic display in a fighter aircraft environment has presented a unique set of technical challenges. This paper addresses design concepts used on the Engine Fuel Display and proposes design guidelines generally applicable for AMLCD projects.

Control-system techniques for improved departure/spin resistance for fighter aircraft

NASA Technical Reports Server (NTRS)

Nguyen, L. T.; Gilbert, W. P.; Ogburn, M. E.

1980-01-01

Some fundamental information on control system effects on controllability of highly maneuverable aircraft at high angles of attack are summarized as well as techniques for enhancing fighter aircraft departure/spin resistance using control system design. The discussion includes: (1) a brief review of pertinent high angle of attack phenomena including aerodynamics, inertia coupling, and kinematic coupling; (2) effects of conventional stability augmentation systems at high angles of attack; (3) high angle of attack control system concepts designed to enhance departure/spin resistance; and (4) the outlook for applications of these concepts to future fighters, particularly those designs which incorporate relaxed static stability.

Control research in the NASA high-alpha technology program

NASA Technical Reports Server (NTRS)

Gilbert, William P.; Nguyen, Luat T.; Gera, Joseph

1990-01-01

NASA is conducting a focused technology program, known as the High-Angle-of-Attack Technology Program, to accelerate the development of flight-validated technology applicable to the design of fighters with superior stall and post-stall characteristics and agility. A carefully integrated effort is underway combining wind tunnel testing, analytical predictions, piloted simulation, and full-scale flight research. A modified F-18 aircraft has been extensively instrumented for use as the NASA High-Angle-of-Attack Research Vehicle used for flight verification of new methods and concepts. This program stresses the importance of providing improved aircraft control capabilities both by powered control (such as thrust-vectoring) and by innovative aerodynamic control concepts. The program is accomplishing extensive coordinated ground and flight testing to assess and improve available experimental and analytical methods and to develop new concepts for enhanced aerodynamics and for effective control, guidance, and cockpit displays essential for effective pilot utilization of the increased agility provided.

Physiological profile of fighters influences training organisation in combat sports: response to Del Vecchio, Hirata, and Franchini (2011).

PubMed

Paillard, Thierry

2011-12-01

The article by Del Vecchio, et al. (2011) provides relevant information to trainers about the effort-pause ratio during mixed martial arts matches. Taking into account the physiological profiles of fighters would increase interest in these findings.

A user's guide to the Langley 16-foot transonic tunnel complex. Revision 1

NASA Technical Reports Server (NTRS)

1990-01-01

The operational characteristics and equipment associated with the Langley 16-foot transonic tunnel complex which is located in buildings 1146 and 1234 at the Langley Research Center are described in detail. This complex consists of the 16-foot transonic wind tunnel, the static test facility, and the 16- by 24-inch water tunnel research facilities. The 16-foot transonic tunnel is a single-return atmospheric wind tunnel with a 15.5 foot diameter test section and a Mach number capability from 0.20 to 1.30. The emphasis for research conducted in this research complex is on the integration of the propulsion system into advanced aircraft concepts. In the past, the primary focus has been on the integration of nozzles and empennage into the afterbody of fighter aircraft. During the last several years this experimental research has been expanded to include developing the fundamental data base necessary to verify new theoretical concepts, inlet integration into fighter aircraft, nozzle integration for supersonic and hypersonic transports, nacelle/pylon/wing integration for subsonic transport configurations, and the study of vortical flows (in the 16- by 24-inch water tunnel). The purpose here is to provide a comprehensive description of the operational characteristics of the research facilities of the 16-foot transonic tunnel complex and their associated systems and equipments.

YF-22 in flight (US AF photo)

NASA Technical Reports Server (NTRS)

1990-01-01

The YF-22, prototype aircraft for the Air Force's F-22 fighter, cruises over the desert on a flight for the Air Force. It was never involved in any programs with Dryden. The United States Air Force announced the demonstration/validation phase contractors selection for the Advanced Tactical Fighter (ATF) program October 31, 1986. These contractor programs were the Lockheed YF-22 and the Northrop YF-23; each produced two prototypes and ground-based avionics testbeds. First flights of all four prototypes occured in 1990. The YF-22 was first flown on Sept. 29, 1990. The YF-22 was powered by two General Electric YF120-GE-100 engines. The final design, the F-22, was flown sometime in May 1997. The F-22 is capable of efficient supersonic operation without afterburner use (supercruise). Lockheed teamed with General Dynamics (Fort Worth) and Boeing Military Airplanes to produce two YF-22 prototypes, civil registrations N22YF (with GE YF120) and N22YX (P&W YF119). N22YF rolled out at Palmdale August 29, 1990; first flight/ferry to Edwards AFB September 29, 1990; first air refuelling (11th sortie) October 26, 1990; thrust vectoring in flight November 15, 1990; achieved Mach 1.8 December 26, 1990. Flight test demonstrations included `supercruise' flight in excess of Mach 1.58 without afterburner.

Multiaxis control power from thrust vectoring for a supersonic fighter aircraft model at Mach 0.20 to 2.47

NASA Technical Reports Server (NTRS)

Capone, Francis J.; Bare, E. Ann

1987-01-01

The aeropropulsive characteristics of an advanced twin-engine fighter aircraft designed for supersonic cruise have been studied in the Langley 16-Foot Tansonic Tunnel and the Lewis 10- by 10-Foot Supersonic Tunnel. The objective was to determine multiaxis control-power characteristics from thrust vectoring. A two-dimensional convergent-divergent nozzle was designed to provide yaw vector angles of 0, -10, and -20 deg combined with geometric pitch vector angles of 0 and 15 deg. Yaw thrust vectoring was provided by yaw flaps located in the nozzle sidewalls. Roll control was obtained from differential pitch vectoring. This investigation was conducted at Mach numbers from 0.20 to 2.47. Angle of attack was varied from 0 to about 19 deg, and nozzle pressure ratio was varied from about 1 (jet off) to 28, depending on Mach number. Increments in force or moment coefficient that result from pitch or yaw thrust vectoring remain essentially constant over the entire angle-of-attack range of all Mach numbers tested. There was no effect of pitch vectoring on the lateral aerodynamic forces and moments and only very small effects of yaw vectoring on the longitudinal aerodynamic forces and moments. This result indicates little cross-coupling of control forces and moments for combined pitch-yaw vectoring.

Technical Evaluation Report, Part A - Vortex Flow and High Angle of Attack

NASA Technical Reports Server (NTRS)

Luckring, James M.

2003-01-01

A symposium entitled Vortex Flow and High Angle of Attack was held in Loen, Norway, from May 7 through May 11, 2001. The Applied Vehicle Technology (AVT) panel, under the auspices of the Research and Technology Organization (RTO), sponsored this symposium. Forty-eight papers, organized into nine sessions, addressed computational and experimental studies of vortex flows pertinent to both aircraft and maritime applications. The studies also ranged from fundamental fluids investigations to flight test results, and significant results were contributed from a broad range of countries. The principal emphasis of this symposium was on "the understanding and prediction of separation-induced vortex flows and their effects on military vehicle performance, stability, control, and structural design loads." It was further observed by the program committee that "separation- induced vortex flows are an important part of the design and off-design performance of conventional fighter aircraft and new conventional or unconventional manned or unmanned advanced vehicle designs (UAVs, manned aircraft, missiles, space planes, ground-based vehicles, and ships)." The nine sessions addressed the following topics: vortical flows on wings and bodies, experimental techniques for vortical flows, numerical simulations of vortical flows, vortex stability and breakdown, vortex flows in maritime applications, vortex interactions and control, vortex dynamics, flight testing, and vehicle design. The purpose of this paper is to provide brief reviews of these papers along with some synthesizing perspectives toward future vortex flow research opportunities. The paper includes the symposium program. (15 refs.)

Recent advances in a linear micromirror array for high-resolution projection

NASA Astrophysics Data System (ADS)

Picard, Francis; Doucet, Michel; Niall, Keith K.; Larouche, Carl; Savard, Maxime; Crisan, Silviu; Thibault, Simon; Jerominek, Hubert

2004-05-01

The visual displays of contemporary military flight simulators lack adequate definition to represent scenes in basic fast-jet fighter tasks. For example, air-to-air and air-to-ground targets are not projected with sufficient contrast and resolution for a pilot to perceive aspect, aspect rate and object detail at real world slant ranges. Simulator display geometries require the development of ultra-high resolution projectors with greater than 20 megapixel resolution at 60 Hz frame rate. A new micromirror device has been developed to address this requirement; it is able to modulate light intensity in an analog fashion with switching times shorter than 5 μs. When combined with a scanner, a laser and Schlieren optics, a linear array of these flexible micromirrors can display images composed of thousands of lines at a frame rate of 60 Hz. Recent results related to evaluation of this technology for high resolution projection are presented. Alternate operation modes for light modulation with flexible micromirrors are proposed. The related importance of controlling the residual micromirror curvature is discussed and results of experiments investigating the use of the deposition pressure to achieve such control are reported. Moreover, activities aiming at minimizing the micromirror response time and, so doing, maximizing the number of image columns per image frame are discussed. Finally, contrast measurement and estimate of the contrast limit achievable with the flexible micromirror technology are presented. All reported activities support the development of a fully addressable 2000-element micromirror array.

Screening studies of advanced control concepts for airbreathing engines

NASA Technical Reports Server (NTRS)

Ouzts, Peter J.; Lorenzo, Carl F.; Merrill, Walter C.

1993-01-01

The application of advanced control concepts to airbreathing engines may yield significant improvements in aircraft/engine performance and operability. Accordingly, the NASA Lewis Research Center has conducted screening studies of advanced control concepts for airbreathing engines to determine their potential impact on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed concepts was formulated by NASA and industry. These concepts were evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation, three target aircraft/engine combinations were considered: a military high performance fighter mission, a high speed civil transport mission, and a civil tiltrotor mission. Each of the advanced control concepts considered in the study were defined and described. The concept's potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts were also determined. Finally, the concepts were ranked with respect to the target aircraft/engine missions.

Advanced integrated life support system update

NASA Technical Reports Server (NTRS)

Whitley, Phillip E.

1994-01-01

The Advanced Integrated Life Support System Program (AILSS) is an advanced development effort to integrate the life support and protection requirements using the U.S. Navy's fighter/attack mission as a starting point. The goal of AILSS is to optimally mate protection from altitude, acceleration, chemical/biological agent, thermal environment (hot, cold, and cold water immersion) stress as well as mission enhancement through improved restraint, night vision, and head-mounted reticules and displays to ensure mission capability. The primary emphasis to date has been to establish garment design requirements and tradeoffs for protection. Here the garment and the human interface are treated as a system. Twelve state-off-the-art concepts from government and industry were evaluated for design versus performance. On the basis of a combination of centrifuge, thermal manikin data, thermal modeling, and mobility studies, some key design parameters have been determined. Future efforts will concentrate on the integration of protection through garment design and the use of a single layer, multiple function concept to streamline the garment system.

Performance improvements of a highly integrated digital electronic control system for an F-15 airplane

NASA Technical Reports Server (NTRS)

Putnam, T. W.; Burcham, F. W., Jr.; Andries, M. G.; Kelly, J. B.

1985-01-01

The NASA highly integrated digital electronic control (HIDEC) program is structured to conduct flight research into the benefits of integrating an aircraft flight control system with the engine control system. A brief description of the HIDEC system installed on an F-15 aircraft is provided. The adaptive engine control system (ADECS) mode is described in detail, together with simulation results and analyses that show the significant excess thrust improvements achievable with the ADECS mode. It was found that this increased thrust capability is accompanied by reduced fan stall margin and can be realized during flight conditions where engine face distortion is low. The results of analyses and simulations also show that engine thrust response is improved and that fuel consumption can be reduced. Although the performance benefits that accrue because of airframe and engine control integration are being demonstrated on an F-15 aircraft, the principles are applicable to advanced aircraft such as the advanced tactical fighter and advanced tactical aircraft.

Damage tolerance certification of a fighter horizontal stabilizer

NASA Astrophysics Data System (ADS)

Huang, Jia-Yen; Tsai, Ming-Yang; Chen, Jong-Sheng; Ong, Ching-Long

1995-05-01

A review of the program for the damage tolerance certification test of a composite horizontal stabilizer (HS) of a fighter is presented. The object of this program is to certify that the fatigue life and damage tolerance strength of a damaged composite horizontal stabilizer meets the design requirements. According to the specification for damage tolerance certification, a test article should be subjected to two design lifetimes of flight-by-flight load spectra simulating the in-service fatigue loading condition for the aircraft. However, considering the effect of environmental change on the composite structure, one additional lifetime test was performed. In addition, to evaluate the possibilities for extending the service life of the structure, one more lifetime test was carried out with the spectrum increased by a factor of 1.4. To assess the feasibility and reliability of repair technology on a composite structure, two damaged areas were repaired after two lifetimes of damage tolerance test. On completion of four lifetimes of the damage tolerance test, the static residual strength was measured to check whether structural strength after repair met the requirements. Stiffness and static strength of the composite HS with and without damage were evaluated and compared.

The Fighters of Lashkar-e-Taiba: Recruitment, Training, Deployment and Death

DTIC Science & Technology

2013-04-01

false. First,  the vast  majority  of  LeT  fighters  are  Pakistani  and  most  are  Punjabi ,  not  Kashmiri.  It  is  noteworthy  that  there  is...this  database  died  in  Indian‐administered  Kashmir.  This  truth,  taken with  the  predominantly  Pakistani‐ Punjabi   origins  of  the  fighters...2002.    RESIDENCE AND RECRUITMENT    Scholars have  long  claimed  that LeT  is primarily  a  Punjabi   organization  and  that  its  membership  is

From Les Chevaliers du Ciel to Steely-Eyed Killers: Intersecting Influences of Hollywood and Reality on the Romanticization of Fighter Pilots

DTIC Science & Technology

2013-12-01

is critical to establishing his heroic identity . Authority Issues: Whether portrayed via confrontation (e.g., Fighter Squadron, The Dawn Patrol...traits throughout the subject’s cinema history has solidified the archetype into the public’s subconscious. Some combination of youthfulness

Calculation of High Angle of Attack Aerodynamics of Fighter Configurations. Volume 1. Steady

DTIC Science & Technology

1991-04-01

patterns are now well known qualitatively for fighter configurations from extensive wind and water tunnel tests. However, development of quantitative ...Illustration of Flow Features Predicted in the Present Method -55- z -I1 Figure 2. Difinition of Airplane Coordinate Systems -56- zz T .. l y vy.y Mean

Program Fighter - An Evaluation.

ERIC Educational Resources Information Center

Hull, David G.; Fowler, Wallace T.

Described is a computer program for the sizing of subsonic and supersonic fighters which has been adapted for use in an aerospace engineering design course. Following a description of the program, an evaluation of its use in the university is presented. It is concluded that computer programs for the conceptual design of aerospace vehicles can play…

Perceived safety and biomechanical stress to the lower limbs when stepping down from fire fighting vehicles.

PubMed

Giguère, Denis; Marchand, Denis

2005-01-01

Injuries related to emergency vehicles represent 19% of compensated work accidents for fire fighters, 37% of which occur while stepping down from their vehicles. This study compared the impact forces, the use of upper limbs and the perception of danger of fire fighters as they step down from five different locations on fire trucks. The results show that stepping down from the crew cab facing the street produces impact forces averaging 3.2 times the subject's body weight, but is also perceived as the safest way to descend in one of the two groups of fire fighters that participated in the study. Stepping down from the same location, but facing the truck, produced significantly less impact force and a better distribution of the energy over time. This may be achieved through better control of the descending leg, ankle flexion, and the use of grab bars. A re-design of the access to emergency vehicles should take into account both the safety needs and reduction in biomechanical stress of fire fighters.

Expanded R&D by Jet-engine-steering Revolution

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2017-11-01

Since 1987 [1,2,3,4,5] the global jet engine community is facing the historical fact that jet engine steering is gradually replacing canards and the common, often dangerous and obsolete, aerodynamic-only flight control - a fact that (i) has already affected the defense-industrial complex in the US, Russia, China, Japan, S-Korea and India, (ii) has integrated the traditional jet-engine components R&D with advanced aero-electro-physics, stealth technology, thrust vectoring aerodynamics and material science. Moreover, this military revolution is historically due to expand into the civil transport jets domain, [6,7,8,9]. The historical aim of the JES-Revolution remains the same: Replace the common, stall-spin sensitive canards [6] and Aerodynamic-Only-Obsolete-Flight Control ("AOOF Control"). Invented about 100 years ago for propeller-driven air vehicles, it has already been partially replaced for failure to function in WVR-combat post-stall domain, and for the following reasons: In comparison with complete Tail-Less, Canard-Less, Stealth-JES (Figure 5 and References [1,2,3,4,5,6]), the common AOOF Control increases drag, weight, fuel consumption, complexity, cost, and reduces flight safety, stealth, [Low Detectability] and provides zero post-stall, WVR air combat capability while its CANARDS KILL LD & REDUCE JES. Examples of stealth fighter aircraft that have already replaced canards and AOOF-Control where JES provides at least 64 to 0 KILL-RATIO advantage over AOOF-Controlled conventional fighter aircraft: The U.S. JES F-22 and, apparently, the Russian JES-Su-T-50 & 35S, China 2016-J-31, Indian HAL AMCA & FGFA, Japanese JES IHHI ATD-X, S-Korean JES KF-X. Cf. X-44 in Figure 5. Consequently, the jet engine is no longer defined as providing only brute force forward. Instead, it successfully competes with and wins over the wrong, dominating AOOF-Control, at least as a backup flight control whose sole factual domain is currently a well-established, primary flight controller RE any post-stall, super-agility, [2,3,4,5,6,7,8,9].

Advanced controls for airbreathing engines, volume 3: Allison gas turbine

NASA Technical Reports Server (NTRS)

Bough, R. M.

1993-01-01

The application of advanced control concepts to airbreathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for airbreathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two-phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 3 of these reports describes the studies performed by the Allison Gas Turbine Division.

Advanced control for airbreathing engines, volume 1: Pratt and Whitney

NASA Technical Reports Server (NTRS)

Ralph, J. A.

1993-01-01

The application of advanced control concepts to air breathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for air breathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 1 of these reports describes the studies performed by Pratt & Whitney.

Advanced control for airbreathing engines, volume 2: General Electric aircraft engines

NASA Technical Reports Server (NTRS)

Bansal, Indar

1993-01-01

The application of advanced control concepts to air breathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for air breathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 2 of these reports describes the studies performed by GE Aircraft Engines.

Cervical and lumbar pain and radiological degeneration among fighter pilots: a systematic review and meta-analysis.

PubMed

Shiri, Rahman; Frilander, Heikki; Sainio, Markku; Karvala, Kirsi; Sovelius, Roope; Vehmas, Tapio; Viikari-Juntura, Eira

2015-02-01

To assess the associations of acceleration force indicators (aircraft type and flight hours) with cervical and lumbar pain and radiological degeneration among fighter pilots. The PubMed, Embase, Scopus and Web of Science databases were searched until October 2013. Twenty-seven studies were included in the review and 20 in the meta-analysis. There were no differences in the prevalence of neck pain (pooled OR=1.07, 95% CI 0.87 to 1.33), cervical disc degeneration (OR=1.26, CI 0.81 to 1.96), low back pain (OR=0.80, CI 0.47 to 1.38) or lumbar disc degeneration (OR=0.87, CI 0.67 to 1.13) between fighter pilots and helicopter or transport/cargo pilots. Moreover, the prevalence of cervical (OR=1.14, CI 0.61 to 2.16) or lumbar (OR=1.05, CI 0.49 to 2.26) disc degeneration did not differ between fighter pilots and non-flying personnel. Most studies did not control their estimates for age and other potential confounders. Among high-performance aircraft pilots, exposure to the highest G-forces was associated with a higher prevalence of neck pain compared with exposure to lower G-forces (pooled OR=3.12, CI 2.08 to 4.67). The studies on the association between flight hours and neck pain reported inconsistent findings. Moreover, looking back over the shoulder (check six) was the most common posture associated with neck pain. Fighter pilots exposed to high G-forces may be at a greater risk for neck pain than those exposed to low G-forces. This finding should be confirmed with better control for confounding. Awkward neck posture may be an important factor in neck pain among fighter pilots. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Leading-edge vortex research: Some nonplanar concepts and current challenges

NASA Technical Reports Server (NTRS)

Campbell, J. F.; Osborn, R. F.

1986-01-01

Some background information is provided for the Vortex Flow Aerodynamics Conference and that current slender wing airplanes do not use variable leading edge geometry to improve transonic drag polar is shown. Highlights of some of the initial studies combining wing camber, or flaps, with vortex flow are presented. Current vortex flap studies were reviewed to show that there is a large subsonic data base and that transonic and supersonic generic studies have begun. There is a need for validated flow field solvers to calculate vortex/shock interactions at transonic and supersonic speeds. Many important research opportunities exist for fundamental vortex flow investigations and for designing advanced fighter concepts.

Strategic Forum. Number 254, February 2010. U.S.-Mexico Homeland Defense: A Compatible Interface

DTIC Science & Technology

2010-02-01

United States, and the creation of a Mexican P–47 Thunderbolt fighter squadron called the “ Aztec Eagles.” The 201st Mexican Fighter Squadron, Mexican... decline in trade started in 2001 and continued through 2003, with substantial recovery in 2005 and 2006. These trade fig- ures make clear that an

Experimental and analytical investigations to improve low-speed performance and stability and control characteristics of supersonic cruise fighter vehicles

NASA Technical Reports Server (NTRS)

Graham, A. B.

1977-01-01

Small- and large-scale models of supersonic cruise fighter vehicles were used to determine the effectiveness of airframe/propulsion integration concepts for improved low-speed performance and stability and control characteristics. Computer programs were used for engine/airframe sizing studies to yield optimum vehicle performance.

McDonnell XF-88B Experimental Jet Fighter

NASA Image and Video Library

1955-08-10

91,591 Overhead view. McDonnell XF-88B Experimental Jet Fighter. Langley used this aircraft in the mid-1950s to explore the potential of a supersonic propeller. Photographed in Engineer in Charge A History of the Langley Aeronautical Laboratory, 1917-1958 by James R. Hansen. Page 508. **Note see L57-2259 for eye level view.

56TH Fighter Group: ’Wolfpack’ Operations - Air Battle for Berlin.

DTIC Science & Technology

1988-04-01

A pilot from the 63rd FS later reported seeing a yellow nosed fighter attacked and blown up by a Me-109. The 63rd FS pilot subsequently downed that...places one of its aircraft at my disposal by order of the Commanding Officer. Specht and I take off together, with Feldwebel Hauptmann and Sergeant

Inspection. Fire Service Certification Series. Unit FSCS-FF-17-81.

ERIC Educational Resources Information Center

Pribyl, Paul F.

This training unit on inspection is part of a 17-unit course package written to aid instructors in the development, teaching, and evaluation of fire fighters in the Wisconsin Fire Service Certification Series. The purpose stated for the 4.5-hour unit is to give the fire fighters an insight into their responsibilities concerning fire prevention and…

Supportability evaluation of thermoplastic and thermoset composites

NASA Technical Reports Server (NTRS)

Chanani, G. R.; Boldi, D.; Cramer, S. G.; Heimerdinger, M. W.

1990-01-01

Nearly 300 advanced composite components manufactured by Northrop Corporation are flying on U.S. Air Force and U.S. Navy supersonic aircraft as part of a three-year Air Force/Navy/Northrop supportability evaluation. Both thermoplastic and high-temperature thermoset composites were evaluated for their in-service performance on 48 USAF and Navy F-5E fighter and USAFT-38 trainer aircraft in the first large-scale, long-term maintenance evaluation of these advanced materials. Northrop manufactured four types of doors for the project-avionics bay access, oil fill, inlet duct inspection, and a main landing gear door. The doors are made of PEEK (polyetheretherketone) thermoplastic, which is tougher and potentially less expensive to manufacture than conventional composites; and 5250-3 BMI (bismaleimide) thermoset, which is manufactured like a conventional epoxy composite but can withstand higher service temperatures. Results obtained so far indicate that both the BMI and PEEK are durable with PEEK being somewhat better than BMI.

Diffusion measures indicate fight exposure-related damage to cerebral white matter in boxers and mixed martial arts fighters.

PubMed

Shin, W; Mahmoud, S Y; Sakaie, K; Banks, S J; Lowe, M J; Phillips, M; Modic, M T; Bernick, C

2014-02-01

Traumatic brain injury is common in fighting athletes such as boxers, given the frequency of blows to the head. Because DTI is sensitive to microstructural changes in white matter, this technique is often used to investigate white matter integrity in patients with traumatic brain injury. We hypothesized that previous fight exposure would predict DTI abnormalities in fighting athletes after controlling for individual variation. A total of 74 boxers and 81 mixed martial arts fighters were included in the analysis and scanned by use of DTI. Individual information and data on fight exposures, including number of fights and knockouts, were collected. A multiple hierarchical linear regression model was used in region-of-interest analysis to test the hypothesis that fight-related exposure could predict DTI values separately in boxers and mixed martial arts fighters. Age, weight, and years of education were controlled to ensure that these factors would not account for the hypothesized effects. We found that the number of knockouts among boxers predicted increased longitudinal diffusivity and transversal diffusivity in white matter and subcortical gray matter regions, including corpus callosum, isthmus cingulate, pericalcarine, precuneus, and amygdala, leading to increased mean diffusivity and decreased fractional anisotropy in the corresponding regions. The mixed martial arts fighters had increased transversal diffusivity in the posterior cingulate. The number of fights did not predict any DTI measures in either group. These findings suggest that the history of fight exposure in a fighter population can be used to predict microstructural brain damage.

Using multiple IMUs in a stacked filter configuration for calibration and fine alignment

NASA Astrophysics Data System (ADS)

El-Osery, Aly; Bruder, Stephen; Wedeward, Kevin

2018-05-01

Determination of a vehicle or person's position and/or orientation is a critical task for a multitude of applications ranging from automated cars and first responders to missiles and fighter jets. Most of these applications rely primarily on global navigation satellite systems, e.g., GPS, which are highly vulnerable to degradation whether by environmental factors or malicious actions. The use of inertial navigation techniques has been shown to provide increased reliability of navigation systems in these situations. Due to advances in MEMS technology and processing capabilities, the use of small and low-cost inertial measurement units (IMUs) are becoming increasingly feasible, which results in small size, weight and power (SWaP) solutions. A known limitation of MEMS IMUs are errors that causes the navigation solution to drift; furthermore, calibration and initialization are challenging tasks. In this paper, we investigate the use of multiple IMUs to aid in calibrating the navigation system and obtaining accurate initialization by performing fine alignment. By using a centralized filter, physical constraints between the multiple IMUs on a rigid body are leveraged to provide relative updates, which in turn aids in the estimation of the individual biases and scale-factors. Developed algorithms will be validated through simulation and actual measurements using low-cost IMUs.

High flux heat exchanger

NASA Astrophysics Data System (ADS)

Flynn, Edward M.; Mackowski, Michael J.

1993-01-01

This interim report documents the results of the first two phases of a four-phase program to develop a high flux heat exchanger for cooling future high performance aircraft electronics. Phase 1 defines future needs for high flux heat removal in advanced military electronics systems. The results are sorted by broad application categories: (1) commercial digital systems, (2) military data processors, (3) power processors, and (4) radar and optical systems. For applications expected to be fielded in five to ten years, the outlook is for steady state flux levels of 30-50 W/sq cm for digital processors and several hundred W/sq cm for power control applications. In Phase 1, a trade study was conducted on emerging cooling technologies which could remove a steady state chip heat flux of 100 W/sq cm while holding chip junction temperature to 90 C. Constraints imposed on heat exchanger design, in order to reflect operation in a fighter aircraft environment, included a practical lower limit on coolant supply temperature, the preference for a nontoxic, nonflammable, and nonfreezing coolant, the need to minimize weight and volume, and operation in an accelerating environment. The trade study recommended the Compact High Intensity Cooler (CHIC) for design, fabrication, and test in the final two phases of this program.

X-31 wing removal

NASA Image and Video Library

1995-05-18

U.S. and German personnel of the X-31 Enhanced Fighter Maneuverability Technology Demonstrator aircraft program removing the right wing of the aircraft, which was ferried from Edwards Air Force Base, California, to Europe on May 22, 1995 aboard an Air Force Reserve C-5 transport. The X-31, based at the NASA Dryden Flight Research Center was ferried to Europe and flown in the Paris Air Show in June. The wing of the X-31 was removed on May 18, 1995, to allow the aircraft to fit inside the C-5 fuselage. Officials of the X-31 project used Manching, Germany, as a staging base to prepare the aircraft for the flight demonstration. At the air show, the X-31 demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems to provide controlled flight at very high angles of attack. The aircraft arrived back at Edwards in a Air Force Reserve C-5 on June 25, 1995 and off loaded at Dryden June 27. The X-31 aircraft was developed jointly by Rockwell International's North American Aircraft Division (now part of Boeing) and Daimler-Benz Aerospace (formerly Messerschmitt-Bolkow-Blohm), under sponsorship by the U.S. Department of Defense and the German Federal Ministry of Defense.

Fighter Pilot Ejection Study as an Educational Tool

ERIC Educational Resources Information Center

Robinson, Garry; Jovanoski, Zlatko

2010-01-01

In this article, we apply the well-known equations of projectile motion to the case of a fighter pilot ejecting from an aircraft, the aim being to establish under what conditions there is danger of impact with the rear vertical stabilizer. The drag force on the pilot after ejection is assumed to vary as the velocity squared and the aircraft motion…

Challenging the New World Order: The Arms Transfer Policies of the Russian Republic

DTIC Science & Technology

1993-10-01

SU-22 fighter, SU-24 and SU-25 ground attack planes, MiG-29, MiG-31 fighters, 11-76 transports, " secondhand " AN-24 and Yak-40 passenger aircraft, i.e...notably in the Third World, and is the author of a forthcoming study of the Soviet Commissariat of Nationalities and editor of books on Soviet

78 FR 34656 - Record of Decision for the F-15 Aircraft Conversion, 144th Fighter Wing, California Air National...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... DEPARTMENT OF DEFENSE Department of the Air Force Record of Decision for the F-15 Aircraft Conversion, 144th Fighter Wing, California Air National Guard, Fresno-Yosemite International Airport Final... May 31, 2013, the United States Air Force signed the ROD for the F-15 Aircraft Conversion for the...

Sprinklers/Standpipes/Detection Systems. Fire Service Certification Series. Unit FSCS-FF-11-80.

ERIC Educational Resources Information Center

Pribyl, Paul F.

This training unit on sprinklers, standpipes, and detection systems is part of a 17-unit course package written to aid instructors in the development, teaching, and evaluation of fire fighters in the Wisconsin Fire Service Certification Series. The purpose stated for the 6-hour unit is to provide the fire fighter with an understanding of the…

CFD validation experiments at McDonnell Aircraft Company

NASA Technical Reports Server (NTRS)

Verhoff, August

1987-01-01

Information is given in viewgraph form on computational fluid dynamics (CFD) validation experiments at McDonnell Aircraft Company. Topics covered include a high speed research model, a supersonic persistence fighter model, a generic fighter wing model, surface grids, force and moment predictions, surface pressure predictions, forebody models with 65 degree clipped delta wings, and the low aspect ratio wing/body experiment.

Defense.gov Special Report: Travels With Hagel

Science.gov Websites

Force base on the Florida panhandle, talking to pilots from the 33rd Fighter Wing, meeting with and in an F-35 fighter. Troop Event At Eglin Air Force Base More Video Hagel Troop Event Kings Bay Travel Locations Map of Hagel's Trip Naval Submarine Base Kings Bay, Georgia. Eglin Air Force Base, Florida. Fort

Some effects of external stores on the static stability of fighter airplanes

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1972-01-01

Fighter airplanes may have a seemingly limitless number of external store arrangements. Some practical considerations and some aerodynamic considerations must be taken into account in the arrangements of the external stores. The nature of the problems concerning the type of store arrangement involved and the type of airplane on which the stores are installed are reported.

Fire Streams. Fire Service Certification Series. Unit FSCS-FF-10-80.

ERIC Educational Resources Information Center

Pribyl, Paul F.

This training unit on fire streams is part of a 17-unit course package written to aid instructors in the development, teaching, and evaluation of fire fighters in the Wisconsin Fire Service Certification Series. The purpose stated for the 8-hour unit is to provide the fire fighters with an understanding of the characteristics, use, and application…

Joint Counterair and Theater Missile Defense Doctrine to Defend against Unmanned Aerial Vehicles and Cruise Missiles in Asymmetric Warfare

DTIC Science & Technology

2009-02-12

features an Active Electronic Scan Array ( ASEA ) radar and improved electronics to enhance the capability of current front line fighter aircraft to...equipped with the APG-79 ASEA radar and selected squadrons of Air Force F-16 and F-15E have been approved for ASEA upgrades. Next generation fighter

Recent research related to prediction of stall/spin characteristics of fighter aircraft

NASA Technical Reports Server (NTRS)

Nguyen, L. T.; Anglin, E. L.; Gilbert, W. P.

1976-01-01

The NASA Langley Research Center is currently engaged in a stall/spin research program to provide the fundamental information and design guidelines required to predict the stall/spin characteristics of fighter aircraft. The prediction methods under study include theoretical spin prediction techniques and piloted simulation studies. The paper discusses the overall status of theoretical techniques including: (1) input data requirements, (2) math model requirements, and (3) correlation between theoretical and experimental results. The Langley Differential Maneuvering Simulator (DMS) facility has been used to evaluate the spin susceptibility of several current fighters during typical air combat maneuvers and to develop and evaluate the effectiveness of automatic departure/spin prevention concepts. The evaluation procedure is described and some of the more significant results of the studies are presented.

KSC-08pd3592

NASA Image and Video Library

2008-11-07

CAPE CANAVERAL, Fla. – Standing next to a Starfighter aircraft at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida, retired U.S. Air Force Lt. Col. Lee A. Archer Jr., one of the Tuskegee Airmen, shares his experiences as a combat fighter pilot. Earlier, Archer made a special presentation to the Kennedy work force, talking about his years as a combat fighter pilot, civil rights leader and business executive. Archer is the only Tuskegee Airmen fighter pilot to receive the honor “Ace” for shooting down five enemy aircraft during WWII. He retired as Air Force Command Pilot after 30 years of military service, 1941-1971. Archer is at Kennedy to serve as Military Marshall of the 2008 KSC Space & Air Show, Nov. 8-9. Photo credit: NASA/Kim Shiflett

Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

NASA Technical Reports Server (NTRS)

Hernandez, Gloria; Wood, Richard M.; Covell, Peter F.

1994-01-01

An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included.

Proceedings of the Annual Symposium on the Role of Behavioral Science in Physical Security (9th), Symmetry and Asymmetry of Global Adversary Behavior Held at Springfield, Virginia on 3-4 April 1984

DTIC Science & Technology

1984-04-04

when those systems are deployed. Multi- billion dollar investments of the American taxpayers’ money are at stake and taxpayers have a right to expect...meet the most likely—and most important—threats simply are not going to be there, Policy changes on the part of the United States can change all...Thais may be responding incorrectly. For example, they are buying expensive, high-technology fighters when they ought to buy something at lower

Terrestrial EVA Suit = Fire Fighter's Protective Clothing

NASA Technical Reports Server (NTRS)

Foley, Tico; Brown, Robert G.; Burrell, Eddie; DelRosso, Dominic; Krishen, Kumar; Moffitt, Harold; Orndoff, Evelyne; Santos, Beatrice; Butzer, Melissa; Dasgupta, Rajib

1999-01-01

Firefighters want to go to work, do their job well, and go home alive and uninjured. For their most important job, saving lives, firefighters want protective equipment that will allow more extended and effective time at fire scenes in order to perform victim search and rescue. A team, including engineers at NASA JSC and firefighters from Houston, has developed a list of problem areas for which NASA technology and know-how can recommend improvements for firefighter suits and gear. Prototypes for solutions have been developed and are being evaluated. This effort will spin back to NASA as improvements for lunar and planetary suits.

Computational Results for the KTH-NASA Wind-Tunnel Model Used for Acquisition of Transonic Nonlinear Aeroelastic Data

NASA Technical Reports Server (NTRS)

Silva, Walter A.; Chwalowski, Pawel; Wieseman, Carol D.; Eller, David; Ringertz, Ulf

2017-01-01

A status report is provided on the collaboration between the Royal Institute of Technology (KTH) in Sweden and the NASA Langley Research Center regarding the aeroelastic analyses of a full-span fighter configuration wind-tunnel model. This wind-tunnel model was tested in the Transonic Dynamics Tunnel (TDT) in the summer of 2016. Large amounts of data were acquired including steady/unsteady pressures, accelerations, strains, and measured dynamic deformations. The aeroelastic analyses presented include linear aeroelastic analyses, CFD steady analyses, and analyses using CFD-based reduced-order models (ROMs).

Robust recognition of loud and Lombard speech in the fighter cockpit environment

NASA Astrophysics Data System (ADS)

Stanton, Bill J., Jr.

1988-08-01

There are a number of challenges associated with incorporating speech recognition technology into the fighter cockpit. One of the major problems is the wide range of variability in the pilot's voice. That can result from changing levels of stress and workload. Increasing the training set to include abnormal speech is not an attractive option because of the innumerable conditions that would have to be represented and the inordinate amount of time to collect such a training set. A more promising approach is to study subsets of abnormal speech that have been produced under controlled cockpit conditions with the purpose of characterizing reliable shifts that occur relative to normal speech. Such was the initiative of this research. Analyses were conducted for 18 features on 17671 phoneme tokens across eight speakers for normal, loud, and Lombard speech. It was discovered that there was a consistent migration of energy in the sonorants. This discovery of reliable energy shifts led to the development of a method to reduce or eliminate these shifts in the Euclidean distances between LPC log magnitude spectra. This combination significantly improved recognition performance of loud and Lombard speech. Discrepancies in recognition error rates between normal and abnormal speech were reduced by approximately 50 percent for all eight speakers combined.

Experimental study of wing leading-edge devices for improved maneuver performance of a supercritical maneuvering fighter configuration. [Langley 7- by 10-ft high speed tunnel tests

NASA Technical Reports Server (NTRS)

Mann, M. J.; Huffman, J. K.; Fox, C. H., Jr.; Campbell, R. L.

1983-01-01

Wind tunnel tests were conducted to examine the use of wing leading-edge devices for improved subsonic and transonic maneuver performance. These devices were tested on a fighter configuration which utilized supercritical-wing technology. The configuration had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. The tests were conducted at Mach numbers of 0.60 and 0.85 with angles of attack from -0.5 deg to 22 deg. At both Mach numbers, sharp leading-edge flaps produced vortices which greatly altered the flow pattern on the wing and resulted in substantial reductions in drag at high lift. Underwing or pylon-type vortex generators also reduced drag at high lift. The vortex generators worked better at a Mach number of 0.60. The vortex generators gave the best overall results with zero toe-in angle and when mounted on either the outboard part of the wing or at both an outboard location and halfway out the semispan. Both the flaps and the vortex generators had a minor effect on the pitching moment. Fluorescent minitufts were found to be useful for flow visualization at transonic maneuver conditions.

Libyan Former Foreign Fighters and Their Effects on the Libyan Revolution

DTIC Science & Technology

2012-03-23

Glocal organizations; Arab Spring; Sinjar Papers; CJSOTF 120; 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 52...the Libyan Islamic Fighting Group (LIFG) ........................................................................ 13 LIFG and Al Qaeda: A “ Glocal ...to be specifically targeted.(27) LIFG and Al Qaeda Connections: A “ Glocal ” Operation(28) FORMER FOREIGN FIGHTERS AND THEIR EFFECTS ON THE LIBYAN

Seri Rama: converting a shadow play puppet to Street Fighter.

PubMed

Ghani, D B A

2012-01-01

Shadow puppet plays, a traditional Malaysian theater art, is slowly losing its appeal to adolescents, who prefer computer games. To help reverse this decline, the authors incorporated the traditional Seri Rama character into the Street Fighter video game. Using modeling, texturing, and animation, they developed a 3D Seri Rama prototype. Users can control Seri Rama with a PlayStation game controller.

National Nanotechnology Initiative: The Initiative and Its Implementation Plan

DTIC Science & Technology

2000-07-01

precisely controlled size and composition and then to assemble them into larger structures with unique properties and functions will revolutionize...thousand pounds could be stripped from a pilotless fighter aircraft , resulting in longer missions, and fighter agility could be dramatically improved...societal impact: $12 million. e. Major themes and new programs in FY 2001 include : • Nano-biotechnology: biosystems, bio-mimetics and composites (priority

76 FR 41770 - Notice of Intent (NOI) To Prepare An Environmental Impact Statement (EIS) for Proposed Conversion...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-15

... Environmental Impact Statement (EIS) for Proposed Conversion to the F-15 Aircraft for the 144th Fighter Wing... conversion to the F-15 aircraft at the 144th Fighter Wing (144 FW) installation at Fresno-Yosemite... action alternatives analyzed will be a conversion from 18 F-16 PAA to 18 F-15 PAA; or conversion to 24 F...

William W. Momyer: A Biography of an Airpower Mind

DTIC Science & Technology

2013-06-01

Europe to the Mediterranean and Soviet Union 1935-45 ( Helion and Company, West Midlands, England, 2010), 169. 22 Richard G. Davis, Carl A. Spaatz and... Helion and Company, West Midlands, England, 2010), 169. 31 60th Fighter Squadron History, 62-63; 58th Fighter Squadron History, 131; Craven and... Energy Commission (AEC) to recommend, “an intensification of efforts to make atomic weapons available for

Fire Fighter Trainer Environmental Considerations

DTIC Science & Technology

1981-01-08

established by the Environmental Protection Agency and various state and local ordinances. At present, the Navy’s fire fighter train- ing facilities use...necessary. All operational capabilities for military communications equipment have been retained. Each training compartment has a local communications...the state or local air pollution-control agencies on a case-by-case basis. 4.2.4 Japanese Air Pollution-Control Regulations. The Japanese Air Quality

Defeating Violent Nonstate Actors

DTIC Science & Technology

2013-01-01

Chiefs of Staff, December 19, 2012), 38, 39. 4 Ibid. 5 Odierno, Amos, and McRaven, Strategic Landpower, 3. Fighting irregulAr Fighters Defeating...or Ringing Hollow?” Army, August 2013, 18-20. Fighting irregular Fighters Bunker 59 and corruption capability. Organized into private armies...the state. Via one process, the synergistic employment of violence and corruption, plato o plomo (silver or lead in Spanish), results in areas of

German Foreign Fighters in Syria and Iraq

DTIC Science & Technology

2016-03-01

players of a Saudi semi-professional soccer team mobilized as a group to travel and fight in Iraq.47 Yet the Saudi soccer squad is not the only...as their biographical availability and integration into German society. The study finds that German foreign fighters are primarily mobilized through...MASTER OF ARTS IN SECURITY STUDIES (MIDDLE EAST, SOUTH ASIA, SUB-SAHARAN AFRICA) from the NAVAL POSTGRADUATE SCHOOL March 2016

EC95-42939-3

NASA Image and Video Library

1995-02-02

The support crew for the F-16A, the F-16XL no. 1, and the F-16 AFTI are, top row, left to right: Randy Weaver; mechanic, Susan Ligon; mechanic, Bob Garcia; Crew Chief, Rich Kelly; mechanic, Dale Edminister; Avionics Technician. Bottom row, left to right, Art Cope; mechanic, John Huffman; Avionics Technician, Jaime Garcia; Avionics Technician, Don Griffith, Avionics Tech. Co-op student. The F-16A (NASA 516), the only civil registered F-16 in existence, was transferred to Dryden from Langley, and was primarily used in engine tests and for parts. It was subsequently transfered from Dryden. The single-seat F-16XL no. 1 (NASA 849) was most recently used in the Cranked-Arrow Wing Aerodynamics Project (CAWAP) to test boundary layer pressures and distribution. Previously it had been used in a program to investigate the characteristics of sonic booms for NASA's High Speed Research Program. Data from the program will be used in the development of a high speed civilian transport. During the series of sonic boom research flights, the F-16XL was used to probe the shock waves being generated by a NASA SR-71 and record their shape and intensity. The Advanced Fighter Technology Integration (AFTI) F-16 was used to develop and demonstrate technologies to improve navigation and a pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. Earlier research in the joint NASA-Air Force AFTI F-16 program demonstrated voice actuated controls, helmet-mounted sighting and integration of forward-mounted canards with the standard flight control system to achieve uncoupled flight.

EC95-42939-5

NASA Image and Video Library

1995-02-02

The support crew for the F-16A, the F-16XL no. 1, and the F-16 AFTI are, top row, left to right: Randy Weaver; mechanic, Susan Ligon; mechanic, Bob Garcia; Crew Chief, Rich Kelly; mechanic, Dale Edminister; Avionics Technician. Bottom row, left to right, Art Cope; mechanic, John Huffman; Avionics Technician, Jaime Garcia; Avionics Technician, Don Griffith, Avionics Tech. Co-op student. The F-16A (NASA 516), the only civil registered F-16 in existence, was transferred to Dryden from Langley, and was primarily used in engine tests and for parts. It was subsequently transfered from Dryden. The single-seat F-16XL no. 1 (NASA 849) was most recently used in the Cranked-Arrow Wing Aerodynamics Project (CAWAP) to test boundary layer pressures and distribution. Previously it had been used in a program to investigate the characteristics of sonic booms for NASA's High Speed Research Program. Data from the program will be used in the development of a high speed civilian transport. During the series of sonic boom research flights, the F-16XL was used to probe the shock waves being generated by a NASA SR-71 and record their shape and intensity. The Advanced Fighter Technology Integration (AFTI) F-16 was used to develop and demonstrate technologies to improve navigation and a pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. Earlier research in the joint NASA-Air Force AFTI F-16 program demonstrated voice actuated controls, helmet-mounted sighting and integration of forward-mounted canards with the standard flight control system to achieve uncoupled flight.

Cross-sectional study of neck pain and cervical sagittal alignment in air force pilots.

PubMed

Moon, Bong Ju; Choi, Kyong Ho; Yun, Chul; Ha, Yoon

2015-05-01

There is a high prevalence of neck pain in air force pilots; however, the causes are not clear and are considered work-related. Kyphotic changes in the cervical spine have been known to cause neck pain. In this study, we investigated the association between neck pain and cervical kyphosis in air force pilots. This is a cross-sectional study of 63 Republic of South Korea Air Force pilots. We examined the C2-7 absolute rotation angle (ARA) using the posterior tangent method and other radiologic parameters on whole spine lateral radiographs. We divided the participants into a neck pain group (N = 32) and no neck pain group (N = 31), and subsequently analyzed the difference in radiographic parameters and clinical data between the two groups. There were no significant differences found in age, body mass index, total flight time, or aerobic or anaerobic exercise between the neck pain and control groups. The fighter pilots had higher 1-yr prevalence of neck pain than nonfighter pilots (84.4% vs. 15.6%). The lower C2-7 ARA (OR = 0.91, 95% CI 0.846, 0.979) and fighter type aircrafts (OR = 3.93, 95% CI 1.104, 13.989) were associated with neck pain. Fighter pilots experienced neck pain more frequently than the nonfighter pilots. Those fighter pilots suffering from neck pain were shown to have more kyphotic changes in the cervical spine than control pilots through evaluation of whole spine lateral radiographs using the posterior tangent method. These key findings suggest that the forces involved in flying a fighter type aircraft may affect cervical alignment and neck pain.

Home Cervical Traction to Reduce Neck Pain in Fighter Pilots.

PubMed

Chumbley, Eric M; O'Hair, Nicole; Stolfi, Adrienne; Lienesch, Christopher; McEachen, James C; Wright, Bruce A

2016-12-01

Most fighter pilots report cervical pain during their careers. Recommendations for remediation lack evidence. We sought to determine whether regular use of a home cervical traction device could decrease reported cervical pain in F-15C pilots. An institutional review board-approved, Health Insurance Portability and Accountability Act-compliant, controlled crossover study was undertaken with 21 male F-15C fighter pilots between February and June 2015. Of the 21 subjects, 12 completed 6 wk each of traction and control, while logging morning, postflying, and post-traction pain. Pain was compared with paired t-tests between the periods, from initial pain scores to postflying, and postflying to post-traction. In the traction phase, initial pain levels increased postflight, from 1.2 (0.7) to 1.6 (1.0) Subsequent post-traction pain levels decreased to 1.3 (0.9), with a corresponding linear decrease in pain relative to pain reported postflight. The difference in pain levels after traction compared to initial levels was not significant, indicating that cervical traction was effective in alleviating flying-related pain. Control pain increased postflight from 1.4 (0.9) to 1.9 (1.3). Daily traction phase pain was lower than the control, but insignificant. To our knowledge, this is the first study of home cervical traction to address fighter pilots' cervical pain. We found a small but meaningful improvement in daily pain rating when using cervical traction after flying. These results help inform countermeasure development for pilots flying high-performance aircraft. Further study should clarify the optimal traction dose and timing in relation to flying.Chumbley EM, O'Hair N, Stolfi A, Lienesch C, McEachen JC, Wright BA. Home cervical traction to reduce neck pain in fighter pilots. Aerosp Med Hum Perform. 2016; 87(12):1010-1015.

Development of infrared scene projectors for testing fire-fighter cameras

NASA Astrophysics Data System (ADS)

Neira, Jorge E.; Rice, Joseph P.; Amon, Francine K.

2008-04-01

We have developed two types of infrared scene projectors for hardware-in-the-loop testing of thermal imaging cameras such as those used by fire-fighters. In one, direct projection, images are projected directly into the camera. In the other, indirect projection, images are projected onto a diffuse screen, which is then viewed by the camera. Both projectors use a digital micromirror array as the spatial light modulator, in the form of a Micromirror Array Projection System (MAPS) engine having resolution of 800 x 600 with mirrors on a 17 micrometer pitch, aluminum-coated mirrors, and a ZnSe protective window. Fire-fighter cameras are often based upon uncooled microbolometer arrays and typically have resolutions of 320 x 240 or lower. For direct projection, we use an argon-arc source, which provides spectral radiance equivalent to a 10,000 Kelvin blackbody over the 7 micrometer to 14 micrometer wavelength range, to illuminate the micromirror array. For indirect projection, an expanded 4 watt CO II laser beam at a wavelength of 10.6 micrometers illuminates the micromirror array and the scene formed by the first-order diffracted light from the array is projected onto a diffuse aluminum screen. In both projectors, a well-calibrated reference camera is used to provide non-uniformity correction and brightness calibration of the projected scenes, and the fire-fighter cameras alternately view the same scenes. In this paper, we compare the two methods for this application and report on our quantitative results. Indirect projection has an advantage of being able to more easily fill the wide field of view of the fire-fighter cameras, which typically is about 50 degrees. Direct projection more efficiently utilizes the available light, which will become important in emerging multispectral and hyperspectral applications.

An Apparatus for Varying Effective Dihedral in Flight with Application to a Study of Tolerable Dihedral on a Conventional Fighter Airplane

NASA Technical Reports Server (NTRS)

Kauffman, William M; Liddell, Charles J , Jr; Smith, Allan; Van Dyke, Rudolph D , Jr

1949-01-01

An apparatus for varying effective dihedral in flight by means of servo actuation of the ailerons in response to sideslip angle is described. The results of brief flight tests of the apparatus on a conventional fighter airplane are presented and discussed. The apparatus is shown to have satisfactory simulated a wide range of effective dihedral under static and dynamic conditions. The effects of a small amount of servo lag are shown to be measurable when the apparatus is simulating small negative values of dihedral. However, these effects were not considered by the pilots to give the airplane an artificial feel. The results of an investigation employing the apparatus to determine the tolerable (safe for normal fighter operation) range of effective dihedral on the test airplane are presented.

What boxing tells us about repetitive head trauma and the brain.

PubMed

Bernick, Charles; Banks, Sarah

2013-01-01

Boxing and other combat sports may serve as a human model to study the effects of repetitive head trauma on brain structure and function. The initial description of what is now known as chronic traumatic encephalopathy (CTE) was reported in boxers in 1928. In the ensuing years, studies examining boxers have described the clinical features of CTE, its relationship to degree of exposure to fighting, and an array of radiologic findings. The field has been hampered by issues related to study design, lack of longitudinal follow-up, and absence of agreed-upon clinical criteria for CTE. A recently launched prospective cohort study of professional fighters, the Professional Fighters Brain Health Study, attempts to overcome some of the problems in studying fighters. Here, we review the cross-sectional results from the first year of the project.

Historical development of worldwide supersonic aircraft

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1979-01-01

Aerodynamic problems in the development of supersonic aircraft, their solutions, and innovative design features are presented. Studies of compressibility, introduction of jets, supersonic phenomena, transonic drag and lift, longitudinal and directional stability, dynamic pressure fields, and advent of the supersonic fighter are discussed. The flight research aircraft such as the Bell X-1 and the Douglas-558, the century series models, reconnaissance aircraft, the multimission tactical fighter, and the current generation fighters such as F-16 and F-18 are described. The SCAT program is considered, along with supersonic developments in Great Britain, France, and USSR. It is concluded that the sonic boom still appears to be an inherent problem of supersonic flight that particularly affects overland commercial flight, and efforts continue for increased efficiency for economic and performance gains and increased safety for military and civilian aircraft.

Emergence of solid state helmet-mounted displays in military applications

NASA Astrophysics Data System (ADS)

Casey, Curtis J.

2002-08-01

Helmet Mounted Displays (HMDs) are used to provide pilots with out-the-window capabilities for engaging tactical threats. The first modern system to be employed was the Apache Integrated Helmet Display Sighting System (IHADSS). Using an optical tracker and multiple sensors, the pilot is able to navigate and engage the enemy with his weapons systems cued by the HMD in day and night conditions. Over the next several years HMDs were tested on tactical jet aircraft. The tactical fighter environment - high G maneuvering and the possibility of ejection - created several problems regarding integration and head-borne weight. However, these problems were soon solved by American, British, Israeli, and Russian companies and are employed or in the process of employment aboard the respective countries' tactical aircraft. It is noteworthy that the current configuration employs both the Heads-Up Display (HUD) as well as the HMD. The new Joint Strike Fighter (JSF), however, will become the first tactical jet to employ only a HMD. HMDs have increasingly become part of the avionics and weapons systems of new aircraft and helicopter platforms. Their use however, is migrating to other military applications. They are currently under evaluation on Combat Vehicle platforms for driving tasks to target acquisition and designation tasks under near-all weather, 24-hour conditions. Their use also has penetrated the individual application such as providing data and situational awareness to the individual soldier; the U.S. Army's Land Warrior Program is an example of this technology being applied. Current HMD systems are CRT-based and have many short-comings, including weight, reliability. The emergence of new microelectronics and solid state image sources - Flat Panel Displays (FPDs) - however, has expanded the application of vision devices across all facets of military applications. Some of the greatest contributions are derived from the following Enabling Technologies, and it is upon those technologies and their applications to HMDs that this paper will address: ¸ Active Matrix Liquid Crystal Displays; improved response times, compensation films ¸ Sub-micron electronics ¸ Backlight Technology to address brightness issues across the spectrum of operations ¸ Distortion Correction to compensate for optical aberrations in near-real time.

Assessment of aerodynamic performance of V/STOL and STOVL fighter aircraft

NASA Technical Reports Server (NTRS)

Nelms, W. P.

1984-01-01

The aerodynamic performance of V/STOL and STOVL fighter/attack aircraft was assessed. Aerodynamic and propulsion/airframe integration activities are described and small and large scale research programs are considered. Uncertainties affecting aerodynamic performance that are associated with special configuration features resulting from the V/STOL requirement are addressed. Example uncertainties relate to minimum drag, wave drag, high angle of attack characteristics, and power induced effects.

A Communication Protocol for CyAMS and the Cyber Fighter Associate Interface

DTIC Science & Technology

2015-05-01

by David Harman , Scott Brown, Brian Henz, and Lisa M Marvel Approved for public release; distribution unlimited...Laboratory A Communication Protocol for CyAMS and the Cyber Fighter Associate Interface by David Harman College Qualified Leaders Student...CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) David Harman , Scott Brown, Brian Henz, and Lisa M Marvel 5d. PROJECT

Price vs. Performance: The Value of Next Generation Fighter Aircraft

DTIC Science & Technology

2007-03-01

forms. Both the semi-log and log-log forms were plagued with heteroskedasticity (according to the Breusch - Pagan /Cook-Weisberg test ). The RDT&E models...from 1949-present were used to construct two models – one based on procurement costs and one based on research, design, test , and evaluation (RDT&E...fighter aircraft hedonic models include several different categories of variables. Aircraft procurement costs and research, design, test , and

Reducing Air Force Fighter Pilot Shortages

DTIC Science & Technology

2015-12-31

that active-component fighter pilot requirements (particularly nonflying staff requirements) exceed its capacity to train and provide initial...pilots in the reserve components. This research was sponsored by four elements of the U.S. Air Force: the Deputy Chief of Staff for Operations (AF/A3...the Deputy Chief of Staff for Manpower, Personnel and Services (AF/A1); the Commander, Air Force Reserve Command (AFRC/CC); and the Director, Air

Signaling the End of Deterrence Afforded by Dual Capable Aircraft

DTIC Science & Technology

2017-04-06

INTRODUCTION For more than 60 years, the Unites States and Europe relied on fighter aircraft capable of executing conventional and nuclear strike...missions. Known as dual-capable aircraft (DCA), these fighters were an integral part of the US extended nuclear deterrence strategy in Asia and Europe...force structure, sustainment and modernization by the US and Allied nations allowed tactical nuclear forces to atrophy. Starting in 2010, the US and

Planning for Recall of Maintenance Manpower

DTIC Science & Technology

2015-09-01

per hour as the MT supporting the reserve unit (assuming no premium is paid for hazard duty or locale adjustment). All tasks assigned to the MTs...fighter aircraft. Under certain conditions, the placement of these technicians in their roles as reserve personnel creates disproportionate economic...loss for the parent unit and the reserve unit. The results of an analysis of the F-15D fighter aircraft indicate that the organization costs of the

Acute spinal injury after centrifuge training in asymptomatic fighter pilots.

PubMed

Kang, Kyung-Wook; Shin, Young Ho; Kang, Seungcheol

2015-04-01

Many countries have hypergravity training centers using centrifuges for pilots to cope with a high gravity (G) environment. The high G training carries potential risk for the development of spinal injury. However, no studies evaluated the influence of centrifuge training on the spines of asymptomatic fighter pilots on a large scale. Study subjects were 991 male fighter pilots with high G training at one institution. Subject variables included information about physical characteristics, flight hours of pilots prior to the training, and G force exposure related factors during training. The two dependent variables were whether the pilots developed acute spinal injury after training and the severity of the injury (major/minor). The incidence of acute spinal injury after high G training was 2.3% (23 of 991 subjects). There were 19 subjects who developed minor injury and 4 subjects who developed a herniated intervertebral disc, which is considered a major injury. In multivariate analysis, only the magnitude of G force during training was significantly related to the development of acute spinal injury. However, there was no significant factor related to the severity of the injury. These results suggest that high G training could cause negative effects on fighter pilots' spines. The magnitude of G force during training seemed to be the most significant factor affecting the occurrence of acute spinal injury.

Light weight escape capsule for fighter aircraft

NASA Technical Reports Server (NTRS)

Robert, James A.

1988-01-01

Emergency crew escape capabilities have been less than adequate for fighter aircraft since before WW II. From the over-the-side bailout of those days through the current ejection seat with a rocket catapult, escaping from a disabled aircraft has been risky at best. Current efforts are underway toward developing a high-tech, smart ejection seat that will give fighter pilots more room to live in the sky, but an escape capsule is needed to meet current and future fighter envelopes. Escape capsules have a bad reputation due to past examples of high weight, poor performance and great complexity. However, the advantages available demand that a capsule be developed. This capsule concept will minimize the inherent disavantages and incorporate the benefits while integrating all aspects of crew station design. The resulting design is appropriate for a crew station of the year 2010 and includes improved combat acceleration protection, chemical or biological combat capability, improved aircraft to escape system interaction, and the highest level of escape performance achievable. The capsule is compact, which can allow a reduced aircraft size and weighs only 1200 lb. The escape system weight penalty is only 120 lb higher than that for the next ejection seat and the capsule has a corresponding increase in performance.

Life-history differences favor evolution of male dimorphism in competitive games.

PubMed

Smallegange, Isabel M; Johansson, Jacob

2014-02-01

Many species exhibit two discrete male morphs: fighters and sneakers. Fighters are large and possess weapons but may mature slowly. Sneakers are small and have no weapons but can sneak matings and may mature quickly to start mating earlier in life than fighters. However, how differences in competitive ability and life history interact to determine male morph coexistence has not yet been investigated within a single framework. Here we integrate demography and game theory into a two-sex population model to study the evolution of strategies that result in the coexistence of fighters and sneakers. We incorporate differences in maturation time between the morphs and use a mating-probability matrix analogous to the classic hawk-dove game. Using adaptive dynamics, we show that male dimorphism evolves more easily in our model than in classic game theory approaches. Our results also revealed an interaction between life-history differences and sneaker competitiveness, which shows that demography and competitive games should be treated as interlinked mechanisms to understand the evolution of male dimorphism. Applying our approach to empirical data on bulb mites (Rhizoglyphus robini), coho salmon (Oncorhynchus kisutch), and bullhorned dung beetles (Onthophagus taurus) indicates that observed occurrences of male dimorphism are in general agreement with model predictions.

Green Propulsion Auxiliary Power Unit Demonstration at MSFC

NASA Technical Reports Server (NTRS)

Robinson, Joel W.

2014-01-01

In 2012, the National Aeronautics & Space Administration (NASA) Space Technology Mission Directorate (STMD) began the process of building an integrated technology roadmap, including both technology pull and technology push strategies. Technology Area 1 (TA-01)1 for Launch Propulsion Systems is one of fourteen TAs that provide recommendations for the overall technology investment strategy and prioritization of NASA's space technology activities. Identified within TA-01 was the need for a green propulsion auxiliary power unit (APU) for hydraulic power by 2015. Engineers led by the author at the Marshall Space Flight Center (MSFC) have been evaluating green propellant alternatives and have begun the development of an APU test bed to demonstrate the feasibility of use. NASA has residual APU assets remaining from the retired Space Shuttle Program. Likewise, the F-16 Falcon fighter jet also uses an Emergency Power Unit (EPU) that has similar characteristics to the NASA hardware. Both EPU and APU components have been acquired for testing at MSFC. This paper will summarize the status of the testing efforts of green propellant from the Air Force Research Laboratory (AFRL) propellant AFM315E based on hydroxyl ammonium nitrate (HAN) with these test assets.

Studies of aerodynamic technology for VSTOL fighter/attack aircraft

NASA Technical Reports Server (NTRS)

Nelms, W. P.

1978-01-01

The paper summarizes several studies to develop aerodynamic technology for high performance VSTOL aircraft anticipated after 1990. A contracted study jointly sponsored by NASA-Ames and David Taylor Naval Ship Research and Development Center is emphasized. Four contractors analyzed two vertical-attitude and three horizontal-attitude takeoff and landing concepts with gross weights ranging from about 10433 kg (23,000 lb) to 17236 kg (38,000 lb). The aircraft have supersonic capability, high maneuver performance (sustained load factor 6.2 at Mach 0.6, 3048 m (10,000 ft)) and a 4536 kg (10,000-lb) STO overload capability. The contractors have estimated the aerodynamics and identified aerodynamic uncertainties associated with their concept. Example uncertainties relate to propulsion-induced flows, canard-wing interactions, and top inlets. Wind-tunnel research programs were proposed to investigate these uncertainties.

Living Expert System (LEXSYS). Volume 6

DTIC Science & Technology

1989-05-15

NOT CONSIDER A FAST MOVER A THREAT UNLESS YOU ARE THINKING ABOUT THE FLOT AREA. AWAY FROM THE FLOT DEFENSIVE ARRAY FIGHTERS HAVE THE LUXURY TO FLY...HIGHER, INCREASING THEIR RADAR COVERAGE AND DENYING YOUR EFFECTIVE USE OF MASKING. I WOULD AGREE THAT AROUND THE FLOT FIGHTERS ARE MOVING TO FAST AND...SAY THAT AFTER IT COMES OFF THE RAIL, COUNTERMEASURES ARE FEW AND FAR BETWEEN. IN DAYLIGHT, HIGH ANGLE STRAFE IS VERY EFFECTIVE AGAINST HELOS BECAUSE

Redirected Radicals: Understanding the Risk of Altered Targeting Trajectories Among ISIL’s Aspiring Foreign Fighters

DTIC Science & Technology

2016-09-01

severe. Chapter III begins the first part of the comparative case study analysis by focusing on Canada’s current foreign fighter issues, propaganda...violence in their home countries. Through an extensive comparative case study analysis of recent ISIL-related violent incidents and plots in the United...overseas, decided instead to alter their targeting trajectory and commit violence in their home countries. Through an extensive comparative case study

Bringing Cost-Wise Readiness to the Deckplates of a Strike Fighter Squadron Using the Balanced Scorecard

DTIC Science & Technology

2013-12-01

equity employed). Customer measures, such as customer satisfaction , are intended to measure the company’s performance from the customer’s perspective...link between a non-financial measure and a firm’s financial performance. For example, one could meet objectives relating to customer satisfaction ... customer satisfaction . Who then is the customer of a strike fighter squadron? Kaplan and Norton (2004) write extensively about 61 the value

Neil Armstrong Family Memorial Service

NASA Image and Video Library

2012-08-31

U.S. Navy F/A-18 jets from Strike Fighter Squadron (VFA) 106 and Strike Fighter Squadron (VFA) 34, from Naval Air Station Oceana (Va.) fly in a "Missing Man" formation over the Camargo Club following a memorial service celebrating the life of Neil Armstrong, Friday, Aug. 31, 2012, in Cincinnati. Armstrong, the first man to walk on the moon during the 1969 Apollo 11 mission, died Saturday, Aug. 25. He was 82. Photo Credit: (NASA/Bill Ingalls)

Air Base Attacks and Defensive Counters: Historical Lessons and Future Challenges

DTIC Science & Technology

2015-01-01

I. Reid, Murray Scot Tanner, and Barry Wilson, A Question of Balance: Political Context and Military Aspects of the China–Taiwan Dispute, Santa...this case, Ramstein AB, Germany) placed fighter shelters on loops in woods . Although the shelters are clearly visible from directly overhead in...this image, placing them in woods would have made target acquisition and attack more difficult for Warsaw Pact fighters. That is because, in the 1970s

Installation restoration program. Decision document for soil and groundwater at the storage area at the USMC Subleased Area, Site 3. 144th Fighter Wing, California Air National Guard, Fresno Air Terminal, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-01-01

Decision Document for IRP Site No. 3 - Storage Area at the USMC Sublease Area, California Air National Guard, 144th Fighter Wing, Fresno Air Terminal, Fresno, California. This report documents the data, conclusion, and recommendation to support a No Further Remedial Action Planned decision at Site 3 under the IRP.

Historic Properties Report: Stratford Army Engine Plant, Connecticut.

DTIC Science & Technology

1984-07-01

aircraft, Pan American began flights to Argentina, Hawaii, and New Zealand , and by August 1934 the Sikorsky S-42 airplane had set world records for...384;or a lengthy discussion of the Corsair , see William Green, Famous Fighters of the Second World War (Garden City, New York: Doubleday), pp. 79-92...manufacture the Corsair fighter plane. Presently, the Avco Lycoming Division uses the facility to develop and manufacture gas turbine engines. There are

A parametric study of planform and aeroelastic effects on aerodynamic center, alpha- and q- stability derivatives. Appendix D: Procedures used to determine the mass distribution for idealized low aspect ratio two spar fighter wings

NASA Technical Reports Server (NTRS)

Roskam, J.; Hamler, F. R.; Reynolds, D.

1972-01-01

The procedures used to establish the mass matrices characteristics for the fighter type wings studied are given. A description of the procedure used to find the mass associated with a specific aerodynamic panel is presented and some examples of the application of the procedure are included.

Environmental Assessment for a Fighter Detachment Facility, Shaw Air Force Base, South Carolina

DTIC Science & Technology

2005-04-01

provides for the protection and propagation of fish, shellfish, wildlife, and recreation in and on the water. The US Army Corps of Engineers (USACE) is...scirpoides Long-beaked baldrush - SC Floating mats in ponds; pond margins. Ruellia caroliniensis A petunia - SC Woods and wood margins. Sagittaria...supply after conventional treatment, fishing, and the survival and propagation of a balanced indigenous aquatic Final EA for a Fighter Detachment

Recent developments in rotary-balance testing of fighter aircraft configurations at NASA Ames Research Center

NASA Technical Reports Server (NTRS)

Malcolm, G. N.; Schiff, L. B.

1985-01-01

Two rotary balance apparatuses were developed for testing airplane models in a coning motion. A large scale apparatus, developed for use in the 12-Foot Pressure Wind tunnel primarily to permit testing at high Reynolds numbers, was recently used to investigate the aerodynamics of 0.05-scale model of the F-15 fighter aircraft. Effects of Reynolds number, spin rate parameter, model attitude, presence of a nose boom, and model/sting mounting angle were investigated. A smaller apparatus, which investigates the aerodynamics of bodies of revolution in a coning motion, was used in the 6-by-6 foot Supersonic Wind Tunnel to investigate the aerodynamic behavior of a simple representation of a modern fighter, the Standard Dynamic Model (SDM). Effects of spin rate parameter and model attitude were investigated. A description of the two rigs and a discussion of some of the results obtained in the respective test are presented.

Investigation of Reynolds Number Effects on a Generic Fighter Configuration in the National Transonic Facility

NASA Technical Reports Server (NTRS)

Tomek, W. G.; Hall, R. M.; Wahls, R. A.; Luckring, J. M.; Owens, L. R.

2002-01-01

A wind tunnel test of a generic fighter configuration was tested in the National Transonic Facility through a cooperative agreement between NASA Langley Research Center and McDonnell Douglas. The primary purpose of the test was to assess Reynolds number scale effects on a thin-wing, fighter-type configuration up to full-scale flight conditions (that is, Reynolds numbers of the order of 60 million). The test included longitudinal and lateral/directional studies at subsonic and transonic conditions across a range of Reynolds numbers from that available in conventional wind tunnels to flight conditions. Results are presented for three Mach numbers (0.6, 0.8, and 0.9) and three configurations: (1) Fuselage/Wing; (2) Fuselage/Wing/Centerline Vertical Tail/Horizontal Tail; and (3) Fuselage/Wing/Trailing-Edge Extension/Twin Vertical Tails. Reynolds number effects on the longitudinal aerodynamic characteristics are presented herein.

Research and Applications in Aeroelasticity and Structural Dynamics at the NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Abel, Irving

1997-01-01

An overview of recently completed programs in aeroelasticity and structural dynamics research at the NASA Langley Research Center is presented. Methods used to perform flutter clearance studies in the wind-tunnel on a high performance fighter are discussed. Recent advances in the use of smart structures and controls to solve aeroelastic problems, including flutter and gust response are presented. An aeroelastic models program designed to support an advanced high speed civil transport is described. An extension to transonic small disturbance theory that better predicts flows involving separation and reattachment is presented. The results of a research study to determine the effects of flexibility on the taxi and takeoff characteristics of a high speed civil transport are presented. The use of photogrammetric methods aboard Space Shuttle to measure spacecraft dynamic response is discussed. Issues associated with the jitter response of multi-payload spacecraft are discussed. Finally a Space Shuttle flight experiment that studied the control of flexible spacecraft is described.

NASA technology applications team: Applications of aerospace technology

NASA Technical Reports Server (NTRS)

1989-01-01

Two critical aspects of the Applications Engineering Program were especially successful: commercializing products of Application Projects; and leveraging NASA funds for projects by developing cofunding from industry and other agencies. Results are presented in the following areas: the excimer laser was commercialized for clearing plaque in the arteries of patients with coronary artery disease; the ultrasound burn depth analysis technology is to be licensed and commercialized; a phased commercialization plan was submitted to NASA for the intracranial pressure monitor; the Flexible Agricultural Robotics Manipulator System (FARMS) is making progress in the development of sensors and a customized end effector for a roboticized greenhouse operation; a dual robot are controller was improved; a multisensor urodynamic pressure catherer was successful in clinical tests; commercial applications were examined for diamond like carbon coatings; further work was done on the multichannel flow cytometer; progress on the liquid airpack for fire fighters; a wind energy conversion device was tested in a low speed wind tunnel; and the Space Shuttle Thermal Protection System was reviewed.

Recent progress in VSTOL technology

NASA Technical Reports Server (NTRS)

Roberts, L.; Deckert, W. R.

1982-01-01

Progress in vertical and short takeoff and landing (V/STOL) aircraft technology, in particular, during the 1970 to 1980 period at Ames Research Center is discussed. Although only two kinds of V/STOL aircraft (the helicopter and the British direct lift Harrier) have achieved operational maturity, understanding of the technology has vastly improved during this 10 year period. To pursue an aggressive R and D program at a reasonable cost, it was decided to conduct extensive large scale testing in wind tunnel and flight simulation facilities, to develop low cost research aircraft using modified airframes or engines, and to involve other agencies and industry contractors in joint technical and funding arrangements. The STOL investigations include exploring STOL performance using the rotating cylinder flap concept, the augmentor wing, upon initiation of the Quiet Short Haul Research Aircraft program, the upper surface blown flap concept. The VTOL investigations were conducted using a tilt rotor aircraft, resulting in the XV-15 tilt rotor research aircraft. Direct jet lift is now being considered for application to future supersonic fighter aircraft.

Communicating Why: Aligning the Air Force Message

DTIC Science & Technology

2015-02-17

innovation as the Air Force’s HOW, after all the service could not have demonstrated its WHY without it. For example, Lt Col Jimmy Doolittle ...the Doolittle Raid.54 Later in the war, General Doolittle’s first order as the newly appointed commander of the 8th Air Force was to free the...fighters from their strict bomber tether so they could go on the offensive against the German fighters.55 As Doolittle later noted, the German General of

Innovation in the Desert: 9th Air Force Tactical Aviation Logistics in Northwest Africa during World War II

DTIC Science & Technology

2017-06-09

of strategic bombing . Douhet’s theory of airpower rested on four principles. First, the inherent strength of the defense on land would result in...Douhet envisioned the destruction of both the enemy’s airpower and economic capability to produce airpower through strategic bombing .6 While admitting...340-444. 3 fighter aircraft, Douhet believed that fighters were vulnerable to bombing and that their effectiveness after the initial stages of

F-35 Joint Strike Fighter Aircraft (F-35)

DTIC Science & Technology

2015-12-01

Selected Acquisition Report ( SAR ) RCS: DD-A&T(Q&A)823-198 F-35 Joint Strike Fighter Aircraft (F-35) As of FY 2017 President’s Budget Defense...Acquisition Management Information Retrieval (DAMIR) March 21, 2016 08:47:09 UNCLASSIFIED F-35 December 2015 SAR March 21, 2016 08:47:09 UNCLASSIFIED 2...Document OSD - Office of the Secretary of Defense O&S - Operating and Support PAUC - Program Acquisition Unit Cost F-35 December 2015 SAR March 21

Dynamic Function Allocation in Fighter Cockpits.

DTIC Science & Technology

1987-06-30

their ability to play the video game simulation used in this study. This was done in an attempt to conceptually match the subject’s skills to those of...highly trained Air Force pilots. 4 Apparatus Simulation. A single seat fighter cockpit environment was simulated using the F-15 Strike Eagle video game developed...simulator containing three color CRTs. The video game was presented on the CRT located in the HUD position. The subjects controlled the game through a

Viper NHEXS Program: A Viper Pilot Neck Health & Conditioning Guide

DTIC Science & Technology

2012-11-01

recommended in this manual. The Neck vs. Gs Problem At least one acute neck pain episode is reported to occur in an estimated 85% of all pilots flying...high-performance fighter type aircraft, with the yearly prevalence of neck-related pain for all pilots at 56% [1]. Vandebeek reported over 50% of...72% of fighter pilots experience neck pain in relation to flying, while 35% experience some low back pain . The reported average G level for acute

STOCHASTIC DUELS OF LIMITED TIME-DURATION,

DTIC Science & Technology

This paper continues the development of the theory of stochastic duels to include the case where there is a time limitation on the duration of the... duel . An example of this situation is fighter-bomber combat in which the fighter has a very limited fuel supply. In this duel , two contestants (with...variable or (2) constant. The duel proceeds until one or both of the contestants are killed or until the time limit is exceeded. The time limit is either

Sea Fighter Analysis

DTIC Science & Technology

2007-02-01

which is used by the model to drive the normal activities of the crew (Figure C.1-2). These routines consist of a sequential list of high- level...separately. Figure C.1-3: Resources & Logic Sheet C.1.1.4 Scenario The scenario that is performed during a model run is a sequential list of all...were marked with a white fore and aft lineup stripe on both landing spots. Current Sea Fighter design does not provide a hangar; however, there

Smart Power: The United States, Iran, and a Nuclear Deal

DTIC Science & Technology

2014-05-22

fighter aircraft to the Arabian Peninsula.2 1Aljazeera, “Iranian fighters ’fired on US drone in Gulf’,” http://www.aljazeera.com /news/middleeast...declared the Anglo-Iranian Oil Company (AIOC) nationalized on May 1, and in return promised compensation . He set up the National Iranian Oil...Italy, Japan, and the United States. 23Bill, 16. 24William O. Beeman, The “Great Satan” vs. the “ Mad Mullahs (Westport, CT: Greenwood Publishing

Repeated head trauma is associated with smaller thalamic volumes and slower processing speed: the Professional Fighters’ Brain Health Study

PubMed Central

Bernick, Charles; Banks, Sarah J; Shin, Wanyong; Obuchowski, Nancy; Butler, Sam; Noback, Michael; Phillips, Michael; Lowe, Mark; Jones, Stephen; Modic, Michael

2015-01-01

Objectives Cumulative head trauma may alter brain structure and function. We explored the relationship between exposure variables, cognition and MRI brain structural measures in a cohort of professional combatants. Methods 224 fighters (131 mixed martial arts fighters and 93 boxers) participating in the Professional Fighters Brain Health Study, a longitudinal cohort study of licensed professional combatants, were recruited, as were 22 controls. Each participant underwent computerised cognitive testing and volumetric brain MRI. Fighting history including years of fighting and fights per year was obtained from self-report and published records. Statistical analyses of the baseline evaluations were applied cross-sectionally to determine the relationship between fight exposure variables and volumes of the hippocampus, amygdala, thalamus, caudate, putamen. Moreover, the relationship between exposure and brain volumes with cognitive function was assessed. Results Increasing exposure to repetitive head trauma measured by number of professional fights, years of fighting, or a Fight Exposure Score (FES) was associated with lower brain volumes, particularly the thalamus and caudate. In addition, speed of processing decreased with decreased thalamic volumes and with increasing fight exposure. Higher scores on a FES used to reflect exposure to repetitive head trauma were associated with greater likelihood of having cognitive impairment. Conclusions Greater exposure to repetitive head trauma is associated with lower brain volumes and lower processing speed in active professional fighters. PMID:25633832

Hot-bench simulation of the active flexible wing wind-tunnel model

NASA Technical Reports Server (NTRS)

Buttrill, Carey S.; Houck, Jacob A.

1990-01-01

Two simulations, one batch and one real-time, of an aeroelastically-scaled wind-tunnel model were developed. The wind-tunnel model was a full-span, free-to-roll model of an advanced fighter concept. The batch simulation was used to generate and verify the real-time simulation and to test candidate control laws prior to implementation. The real-time simulation supported hot-bench testing of a digital controller, which was developed to actively control the elastic deformation of the wind-tunnel model. Time scaling was required for hot-bench testing. The wind-tunnel model, the mathematical models for the simulations, the techniques employed to reduce the hot-bench time-scale factors, and the verification procedures are described.

An assessment of viscous effects in computational simulation of benign and burst vortex flows on generic fighter wind-tunnel models using TEAM code

NASA Technical Reports Server (NTRS)

Kinard, Tim A.; Harris, Brenda W.; Raj, Pradeep

1995-01-01

Vortex flows on a twin-tail and a single-tail modular transonic vortex interaction (MTVI) model, representative of a generic fighter configuration, are computationally simulated in this study using the Three-dimensional Euler/Navier-Stokes Aerodynamic Method (TEAM). The primary objective is to provide an assessment of viscous effects on benign (10 deg angle of attack) and burst (35 deg angle of attack) vortex flow solutions. This study was conducted in support of a NASA project aimed at assessing the viability of using Euler technology to predict aerodynamic characteristics of aircraft configurations at moderate-to-high angles of attack in a preliminary design environment. The TEAM code solves the Euler and Reynolds-average Navier-Stokes equations on patched multiblock structured grids. Its algorithm is based on a cell-centered finite-volume formulation with multistage time-stepping scheme. Viscous effects are assessed by comparing the computed inviscid and viscous solutions with each other and experimental data. Also, results of Euler solution sensitivity to grid density and numerical dissipation are presented for the twin-tail model. The results show that proper accounting of viscous effects is necessary for detailed design and optimization but Euler solutions can provide meaningful guidelines for preliminary design of flight vehicles which exhibit vortex flows in parts of their flight envelope.

Simulation Based Acquisition for NASA's Office of Exploration Systems

NASA Technical Reports Server (NTRS)

Hale, Joe

2004-01-01

In January 2004, President George W. Bush unveiled his vision for NASA to advance U.S. scientific, security, and economic interests through a robust space exploration program. This vision includes the goal to extend human presence across the solar system, starting with a human return to the Moon no later than 2020, in preparation for human exploration of Mars and other destinations. In response to this vision, NASA has created the Office of Exploration Systems (OExS) to develop the innovative technologies, knowledge, and infrastructures to explore and support decisions about human exploration destinations, including the development of a new Crew Exploration Vehicle (CEV). Within the OExS organization, NASA is implementing Simulation Based Acquisition (SBA), a robust Modeling & Simulation (M&S) environment integrated across all acquisition phases and programs/teams, to make the realization of the President s vision more certain. Executed properly, SBA will foster better informed, timelier, and more defensible decisions throughout the acquisition life cycle. By doing so, SBA will improve the quality of NASA systems and speed their development, at less cost and risk than would otherwise be the case. SBA is a comprehensive, Enterprise-wide endeavor that necessitates an evolved culture, a revised spiral acquisition process, and an infrastructure of advanced Information Technology (IT) capabilities. SBA encompasses all project phases (from requirements analysis and concept formulation through design, manufacture, training, and operations), professional disciplines, and activities that can benefit from employing SBA capabilities. SBA capabilities include: developing and assessing system concepts and designs; planning manufacturing, assembly, transport, and launch; training crews, maintainers, launch personnel, and controllers; planning and monitoring missions; responding to emergencies by evaluating effects and exploring solutions; and communicating across the OExS enterprise, within the Government, and with the general public. The SBA process features empowered collaborative teams (including industry partners) to integrate requirements, acquisition, training, operations, and sustainment. The SBA process also utilizes an increased reliance on and investment in M&S to reduce design risk. SBA originated as a joint Industry and Department of Defense (DoD) initiative to define and integrate an acquisition process that employs robust, collaborative use of M&S technology across acquisition phases and programs. The SBA process was successfully implemented in the Air Force s Joint Strike Fighter (JSF) Program.

On the use of the systems approach to certify advanced aviation technologies

NASA Technical Reports Server (NTRS)

Wise, Mark A.; Wise, John A.

1994-01-01

The field of human factors is as varied and diverse as the human subject itself. But one of its most important applications is the facilitation of safety and efficiency in a particular working environment through the implementation of paradigms known about humans and their working relationship with machines and systems. During the period since World War II (which is often viewed as the birth of Human Factors) no area has been the subject of more human factors research than aviation. And in no time during that epoch is the influence of human factors more important, nor more imperative than it is today. As technology driven designs have been finding their way into the national airspace system (NAS), there has been growing concern within the aviation industry itself, the Federal Aviation Administration (FAA), and the general public for a means by which to certify complex systems and the advanced aviation technologies that will be responsible for transporting, directing, and maintaining our airborne travel. While it is widely agreed human factors certification is desirable, the philosophy that will underlie the approach is debatable. There are, in general, two different approaches to certification: (1) the top-down or systems approach; and, (2) the bottom-up or monadical approach. The top-down approach is characterized by the underlying assumption that certification can be best achieved by looking at the system as a whole, understanding its objectives and operating environment, then examining the constituent parts. In an aircraft cockpit, this would be accomplished by first examining what the aircraft is supposed to be (e.g., fighter, general aviation, passenger), identifying its operating environment (IFR, VMC, combat, etc.) and looking at the entire working system which includes the hardware, software, liveware and their interactions; then, evaluative measures can be applied to the subsystems (e.g., individual instruments, CRT displays, controls). The bottom-up approach is founded on the philosophy that the whole can be best served by first examining it constituent elements. This approach would perform the above certification completely antithetically, by looking at the individual parts and certifying good human factors applications to those parts under the basic assumption that the whole is equal to the sum of its parts.

Effect of wood smoke exposure on vascular function and thrombus formation in healthy fire fighters.

PubMed

Hunter, Amanda L; Unosson, Jon; Bosson, Jenny A; Langrish, Jeremy P; Pourazar, Jamshid; Raftis, Jennifer B; Miller, Mark R; Lucking, Andrew J; Boman, Christoffer; Nyström, Robin; Donaldson, Kenneth; Flapan, Andrew D; Shah, Anoop S V; Pung, Louis; Sadiktsis, Ioannis; Masala, Silvia; Westerholm, Roger; Sandström, Thomas; Blomberg, Anders; Newby, David E; Mills, Nicholas L

2014-12-09

Myocardial infarction is the leading cause of death in fire fighters and has been linked with exposure to air pollution and fire suppression duties. We therefore investigated the effects of wood smoke exposure on vascular vasomotor and fibrinolytic function, and thrombus formation in healthy fire fighters. In a double-blind randomized cross-over study, 16 healthy male fire fighters were exposed to wood smoke (~1 mg/m³ particulate matter concentration) or filtered air for one hour during intermittent exercise. Arterial pressure and stiffness were measured before and immediately after exposure, and forearm blood flow was measured during intra-brachial infusion of endothelium-dependent and -independent vasodilators 4-6 hours after exposure. Thrombus formation was assessed using the ex vivo Badimon chamber at 2 hours, and platelet activation was measured using flow cytometry for up to 24 hours after the exposure. Compared to filtered air, exposure to wood smoke increased blood carboxyhaemoglobin concentrations (1.3% versus 0.8%; P < 0.001), but had no effect on arterial pressure, augmentation index or pulse wave velocity (P > 0.05 for all). Whilst there was a dose-dependent increase in forearm blood flow with each vasodilator (P < 0.01 for all), there were no differences in blood flow responses to acetylcholine, sodium nitroprusside or verapamil between exposures (P > 0.05 for all). Following exposure to wood smoke, vasodilatation to bradykinin increased (P = 0.003), but there was no effect on bradykinin-induced tissue-plasminogen activator release, thrombus area or markers of platelet activation (P > 0.05 for all). Wood smoke exposure does not impair vascular vasomotor or fibrinolytic function, or increase thrombus formation in fire fighters. Acute cardiovascular events following fire suppression may be precipitated by exposure to other air pollutants or through other mechanisms, such as strenuous physical exertion and dehydration.

DFRC F-16 aircraft fleet and support crew

NASA Technical Reports Server (NTRS)

1995-01-01

The support crew for the F-16A, the F-16XL no. 1, and the F-16 AFTI are, top row, left to right: Randy Weaver; mechanic, Susan Ligon; mechanic, Bob Garcia; Crew Chief, Rich Kelly; mechanic, Dale Edminister; Avionics Technician. Bottom row, left to right, Art Cope; mechanic, John Huffman; Avionics Technician, Jaime Garcia; Avionics Technician, Don Griffith, Avionics Tech. Co-op student. The F-16A (NASA 516), the only civil registered F-16 in existence, was transferred to Dryden from Langley, and is primarily used in engine tests and for parts. Although it is flight-worthy, it is not currently flown at Dryden. The single-seat F-16XL no. 1 (NASA 849) was most recently used in the Cranked-Arrow Wing Aerodynamics Project (CAWAP) to test boundary layer pressures and distribution. Previously it had been used in a program to investigate the characteristics of sonic booms for NASA's High Speed Research Program. Data from the program will be used in the development of a high speed civilian transport. During the series of sonic boom research flights, the F-16XL was used to probe the shock waves being generated by a NASA SR-71 and record their shape and intensity. The Advanced Fighter Technology Integration (AFTI) F-16 was used to develop and demonstrate technologies to improve navigation and a pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. Earlier research in the joint NASA-Air Force AFTI F-16 program demonstrated voice actuated controls, helmet-mounted sighting and integration of forward-mounted canards with the standard flight control system to achieve uncoupled flight.

Accurate Modeling of Stability and Control Properties for Fighter Aircraft from CFD

DTIC Science & Technology

2012-03-01

first an aircraft to flight test which is not until late in the design phase where millions if not billions of dollars have already been invested. It...of an aircraft and even late in the design phase there are often large gaps in data due to budget cuts to flight testing and limitations to maneuvers...early in the design cycle has been the source of many costly fixes to fighter aircraft after flight testing begins. Early prediction of these nonlinear

Combat Leadership: 56th Fighter Group 1943-1944.

DTIC Science & Technology

1986-04-01

September-October 1970, pp. 30-35. Meyer, John C ., Col, USAF. "What Makes a Jet Ace?" Air Trails, October 1952, p. 21. Ritchey, Russell V. "Identifying...A-Ri68 864 COMBAT LEADERSHIP: 56TH FIGHTER GROUP i947-1944(U) AIR 1/1 COMMAND AND STAFF COLL MAXWELL RFB RL T L LENTZ APR 86I ACSC-86-1525...Interlibrary Loan Service (AUL/LDEX, Maxwell AFB, Alabama, 36112) or the Defense Technical Information Center. Request 4 must include the author’s name and

Forward Arming and Refueling Points for Fighter Aircraft: Power Projection in an Antiaccess Environment

DTIC Science & Technology

2014-10-01

Arming and Refueling Points for Fighter Aircraft Feature Fifth-Generation Doolittle Raid If we should have to fight, we should be prepared to do so from...the neck up instead of from the neck down. —Gen Jimmy Doolittle The famous Doolittle Raid during World War II offers a superb exam- ple of how an...innovative concept can lead to strategic effects. On 18 April 1942, just four months after the Japanese attack on Pearl Harbor, Lt Col Jimmy Doolittle

Comparing the Effectiveness of Two KC-10 Concepts of Operation - An Examination of Tanker/Airlift Support in a Fighter Deployment to Europe

DTIC Science & Technology

1986-06-01

PROCUREMENT INSTRUMENT IDENTIFICATION NUMBER ORGANIZATION (Ii’ ppticable) Sc. ADDRESS (City, State and ZIP Code) 10. SOURCE OF FUNDING NOS...total of 60 KC-10s were available to support the fighter deployment. This number represented the projected KC-10 procurement for the year 1990 as...search for relevant government studies was accomplished through the Defense Technical Information Center (DTIC). All their 3-9 research related to

Then and Now: Comparing the Flow of Foreign Fighters to AQI and the Islamic State

DTIC Science & Technology

2016-12-01

State during separate blocks of time . Second, it provides insight into the local travel and flow of foreign fighters across time , and the mobilization...who joined the Islamic State during that latter time period also traveled alone more frequently. When they didn’t travel alone, they arrived in...arriving at the caliphate are larger than they were during the time period covered by the Sinjar records. A couple of cases of group travel to Syria

Western Foreign Fighters in Syria: An Empirical Analysis of Recruitment and Mobilization Mechanisms

DTIC Science & Technology

2015-06-01

Malet, Foreign Fighters, 5. 16 Ibid., 4–6. 17 See for example Ines von Behr, Anaïs Reding , Charlie Edwards, and Luke Gribbon, “Radicalization in the...summary see Ines von Behr, Anaïs Reding , Charlie Edwards, and Luke Gribbon, “Radicalization in the Digital Era: The Use of the Internet in 15 Cases of...12; <http://www.lexisnexis.com.libproxy.nps.edu/hottopics/lnacademic> [April 11, 2015]. 134 von Behr, Reding , Edwards, and Gribbon

Proceedings of the Annual Conference of the Military Testing Association (19th), 17-21 October 1977, San Antonio, Texas

DTIC Science & Technology

1979-11-01

to-?ir kills, especially since we will probably be atle to field only a relatively small number of fighter pilots in future wars. Fighter pilots have...Education and Training, Information, And Legal, too many colonel positlons were allocated. Overall, many jobs wer found to be undergraded, especially at the...t preparing the final eppmntice progress/status report, 4e avy C :-vs educacion specialist will regard previous work experience as distri±xtnd

Proposed Relocation of the 37th Tactical Fighter Wing and Other Tactical Force Structure Actions. Draft Environmental Impact Statement

DTIC Science & Technology

1991-02-05

finance , insurance and real estate FL flight level ft feet FWS U.S. Fish and Wildlife Service FWW Fighter Weapon Wing FY fiscal year GAF German Air Force...three locations are related to socioeconomics. Potential effects of the realignment on employment, income, public finance , housing, and local economic...Manufacturing 89 107 1 Transportation, communications, and utilities 135 202 2 * Wholesale and retail tradeb 514 594 5 3 Finance , insurance, and real estate 216

Air Force F-22 Fighter Program: Background and Issues for Congress

DTIC Science & Technology

2009-12-22

comprises a large share of their overall business.23 The Air Force in 2007 estimated that of about 1,000 first-tier F-22 supplier firms, roughly 110, or...fighter.37 In addition, Boeing, the manufacturer of the F-15, is offering for sale on the international market an upgraded version of the F-15 called...Personally I have no interest in the Silent Eagle because it is only stealthy from the front,” Hirata says, referencing a limitation shared by the

The F-35 JSF: Beginning of the End for Blue-Water Ops?

DTIC Science & Technology

2010-04-06

DAMAGED BY INGESTING DEBRIS, THE RESULT OF SWITCHING TO A SINGLE-ENGINE AIRCRAFT FOR THE NAW’S PRIMARY FIGHTER. THE LOCKHEED MARTIN F-35 LIGHTNING II JOINT...States Navy Thesis: Single-engine aircraft have long been considered unsuitable for Naval Aviation, but now the future of blue-water operations is...dependent on the success and reliability of an aircraft · powered by a single engine, the Lockheed -Martin F-35Lightning II Joint Strike Fighter

The Future of the Fighter Pilot ... Will There Be a 6th Generation Fighter?

DTIC Science & Technology

2012-02-02

tndudtng suggestioos lor r &ducing this burden to Washington Headquarters Service, Directorate ror Information Operations and Reports, 1215 Jefferson DaviS...replacement. 22 The concept of spreading R &D risk in this manner at the same time as pre-signing a wide number of future customers was designed to...aviationweek.com/aw/generic/story_channel.jsp ?channel=Defense &id=news/ awst /2011/03/21/AW_03 _21_2011_p27297530.xml&headline=null&next=20>. 33 Ibid

Systems Engineering Processes for the Acquisition of Prognostic and Health Management Systems

DTIC Science & Technology

2012-09-01

INTRODUCTION A. BACKGROUND Prior to the F-35 Joint Strike Fighter (JSF) Program, the A-7 Corsair II was the last single engine fighter in the Navy...first fielded on the A-7 Corsair to the CBM+ systems being developed for the F-35 JSF. It also identified the DoD directive that mandates the...LEFT BLANK 55 LIST OF REFERENCES [1] A-7 Corsair II. (2011, July 7). GlobalSecurity.org. [Online]. Available: http://www.globalsecurity.org

Fire Fighter Trainer Environmental Considerations. Phase II.

DTIC Science & Technology

1981-07-31

NL* 2ffffffffffff m0 h~ hEhI J- L 2 2 * S * MICROCOP Y RI SOLM IION Ii SI CI AN I ’If Conrct No. 1111339-79-C-10011, Mod. No. P0007( i SFIRE FIGHTER...Phosphoric and polyphosphoric acids pose a disposal problem because phosphate compounds are environmentally controlled. Because these compounds do not meet the...acidity from use of these compounds in-a firefight- ing situation do not meet the health and safety criteria for an AFFF substitute; therefore, we

Clinical Utility and Pitfalls of Ultrasound Guided Foreign Body Removal in War Fighters

DTIC Science & Technology

2015-12-01

1 AD_________________ AWARD NUMBER: W81XWH-08-2-0162 TITLE: Clinical Utility and Pitfalls of Ultrasound Guided Foreign Body Removal in War...Clinical Utility and Pitfalls of Ultrasound Guided Foreign Body Removal in War Fighters 5a. CONTRACT NUMBER 5b. GRANT NUMBER: W81XWH-08-2-0162 5c...Purpose: To demonstrate that 1) ultrasound guided foreign body removal (USFBR) is superior to conventional surgery in the cadaver model, 2) USFBR can be

The DTIC Review. Unmanned Aerial Vehicles. Volume 4, Number 2

DTIC Science & Technology

1998-09-01

is likely that today’s fighter force will be retired by 2018 , the 14 F-22 will begin entering retirement in 2025, and that there will be further...Vietarn War Ends Berlin Wall Falls 300 Downsizing axi0 World Wide Recession of 2018 1500 10%0 500"- Figure 3-2. Fighter Force Projection for 2025...Reconnaisance Vehicle UAV’ Enem HQ/Control Command Post JFACC Ig 3700nrm Figure 6-2. StrikeStar C2 Architecture Former Vice Chairman of the Joint

Propane tank explosion (2 deaths, 7 injuries) at Herrig Brothers Feather Creek Farm, Albert City, Iowa, April 9, 1998. Investigation report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1999-09-01

This report explains the explosion/BLEVE that took place on April 9, 1998, at the Herrig Brothers Feather Creek Farm, located in Albert City, Iowa. Two volunteer fire fighters were killed and seven other emergency response personnel were injured. Safety issues covered in the report include protection of propane storage tanks and piping, state regulatory oversight of such installations, and fire fighter response to propane storage tank fires.

Should the Australian Army Adopt the Concept of Effects-Based Operations?

DTIC Science & Technology

2003-06-06

militray effect (Echevarria, 2001). 2 John Boyd was a US Air Force Fighter pilot who developed a model of decision making based on his experiences in the...this cycle, the decision maker (initially a fighter pilot ) would try to reduce the time it took him to go through the cycle. The speed of the decision...cycle was relative, but ultimately, the pilot who could reduce his cycle enough to be “inside”‘ his adversary’s cycle would eventually win. The BOYD

Propulsion simulation test technique for V/STOL configurations

NASA Technical Reports Server (NTRS)

Bailey, R. O.; Smith, S. C.; Bustie, J. B.

1983-01-01

Ames Research Center is developing the technology for turbine-powered jet engine simulators so that airframe/propulsion system interactions on V/STOL fighter aircraft and other highly integrated configurations can be studied. This paper describes the status of the compact multimission aircraft propulsion simulator (CMAPS) technology. Three CMAPS units have accumulated a total of 340 hr during approximately 1-1/2 yr of static and wind-tunnel testing. A wind-tunnel test of a twin-engine CMAPS-equipped close-coupled canard-wing V/STOL model configuration with nonaxisymmetric nozzles was recently completed. During this test approximately 140 total hours were logged on two CMAPS units, indicating that the rotating machinery is reliable and that the CMAPS and associated control system provide a usable test tool. However, additional development is required to correct a drive manifold O-ring problem that limits the engine-pressure-ratio (EPR) to approximately 3.5.

Future Jet Technologies, Part C

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2013-06-01

This updated, PART C REVIEW, covers the dangerous global spread of JS-stealth, drone technology [1-91], canard-free, stealth, new agile drones and the highly debated, 480 billion F-35 International Program as reported on March 13, 2013 to the U.S. Congress [92]. Due to serious design issues, spiraling high costs and years in delays, alternatives are analyzed here, depicted and proposed, mainly from the propulsion-design point of view. These include fleets of low-cost, stealth, jet-steered-drones mixed with non-stealthy, low-cost, ready-to-be-delivered, U.S. or European or Russian fighter aircraft. Can a few F-35s win against large fleets of stealth agile drones? To understand the dangers and critical issues involved, the author's own, past classified information is partly disclosed, while resorting to images in Figs. 2(a) and 2(b) taken from his book [2] and from Wikipedia, the "Free Encyclopedia", in all other images.

F-18 HARV yaw rate expansion flight #125 with Inverted Recovery

NASA Technical Reports Server (NTRS)

1991-01-01

NASA's Dryden Flight Research Center, Edwards, CA, used an F-18 Hornet fighter aircraft as its High Angle-of-Attack (Alpha) Research Vehicle (HARV) in a three-phased flight research program lasting from April 1987 until September 1996. The aircraft completed 385 research flights and demonstrated stabilized flight at angles of attack between 65 and 70 degrees using thrust vectoring vanes, a research flight control system, and (eventually) forebody strakes (hinged structures on the forward side of the fuselage to provide control by interacting with vortices, generated at high angles of attack, to create side forces). This combination of technologies provided carefree handling of a fighter aircraft in a part of the flight regime that was otherwise very dangerous. Flight research with the HARV increased our understanding of flight at high angles of attack (angle of the wings with respect to the direction in which the aircraft was heading), enabling designers of U.S. fighter aircraft to design airplanes that will fly safely in portions of the flight envelope that pilots previously had to avoid. Flight 125 with the HARV involved yaw rate expansion up to 50 degrees per second (moving the nose to the left or right at that rate). NASA research pilot Ed Schneider was the pilot, and the purpose of the flight was to look at the spin characteristics of the HARV. The sequence in this particular video clip includes the first and second maneuvers in the flight. On the first maneuver, the pilot attempted to achieve a yaw rate of 40 degrees per second and actually went to 47 degrees. The spin was oscillatory in pitch (up and down) and roll (rotating around the longitudinal axis). Recovery was normal. On the second maneuver of the flight in which Schneider tried to achieve a yaw rate of 40 degrees per second, the aircraft overshot to 54 degrees per second during an oscillatory spin. In the course of the recovery, the aircraft rolled after a large sideslip buildup. Moderate aft stick application to attain a positive angle of attack resulted in an easy recovery.

Low-speed wind-tunnel test of a STOL supersonic-cruise fighter concept

NASA Technical Reports Server (NTRS)

Coe, Paul L., Jr.; Riley, Donald R.

1988-01-01

A wind-tunnel investigation was conducted to examine the low-speed static stability and control characteristics of a 0.10 scale model of a STOL supersonic cruise fighter concept. The concept, referred to as a twin boom fighter, was designed as a STOL aircraft capable of efficient long range supersonic cruise. The configuration name is derived from the long twin booms extending aft of the engine to the twin vertical tails which support a high center horizontal tail. The propulsion system features a two dimensional thrust vectoring exhaust nozzle which is located so that the nozzle hinge line is near the aircraft center of gravity. This arrangement is intended to allow large thrust vector angles to be used to obtain significant values of powered lift, while minimizing pitching moment trim changes. Low speed stability and control information was obtained over an angle of attack range including the stall. A study of jet induced power effects was included.

Lack of Influence of Apolipoprotein E Status on Cognition or Brain Structure in Professional Fighters

PubMed Central

Miller, Justin B.; Rissman, Robert A.; Bernick, Charles B.

2017-01-01

Abstract The role of the apolipoprotein e4 allele in moderating cognitive and neuroanatomical degeneration following repeated traumatic brain injury is controversial. Here we sought to establish the presence or absence of such a moderating relationship in a prospective study of active and retired boxers and mixed martial arts fighters. Fighters (n = 193) underwent cognitive evaluations, interviews regarding fight history, MRI of the brain, and genetic testing. We used a series of moderator analyses to test for any relationship of apolipoprotein genotype on structural volumes of brain regions previously established to be smaller in those with the most fight exposure, and on cognitive abilities also established to be sensitive to fight exposure. No moderating relationship was detected in any of the analyses. The results of this study suggest that there is no impact of apolipoprotein genotype on the apparent negative association between exposure to professional fighting and brain structure volume or aspects of cognition. PMID:27245878

Investigation of Aerodynamics Scale Effects for a Generic Fighter Configuration in the National Transonic Facility (Invited)

NASA Technical Reports Server (NTRS)

Tomek, W. G.; Wahls, R. A.; Owens, L. R.; Burner, A. B.; Graves, S. S.; Luckring, J. M.

2003-01-01

Two wind tunnel tests of a generic fighter configuration have been completed in the National Transonic Facility. The primary purpose of the tests was to assess Reynolds number scale effects on a thin-wing, fighter-type configuration up to full-scale flight conditions (that is, Reynolds numbers of the order of 60 million). The tests included longitudinal and lateral/directional studies at subsonic and transonic conditions across a range of Reynolds numbers from that available in conventional wind tunnels to flight conditions. Results are presented for three Mach numbers (0.6, 0.8, and 0.9) and three configurations: 1) Fuselage / Wing, 2) Fuselage / Wing / Centerline Vertical Tail / Horizontal Tail, and 3) Fuselage / Wing / Trailing-Edge Extension / Twin Vertical Tails. Reynolds number effects on the lateral-directional aerodynamic characteristics are presented herein, along with longitudinal data demonstrating the effects of fixing the boundary layer transition location for low Reynolds number conditions. In addition, an improved model videogrammetry system and results are discussed.

Injuries to volunteer fire fighters in West Virginia.

PubMed

Magnetti, S M; Wyant, W D; Greenwood, J; Roder, N J; Linton, J C; Ducatman, A M

1999-02-01

The distribution and characteristics of workplace injuries for West Virginia volunteer fire fighters (VFFs) are described using 1992 workers' compensation data. Most of the injuries occurred in VFFs who were less than 30 years of age (62%). The most common type of injuries were those in the category of lacerations and contusions (28.9%), with a notable percentage of injuries due to smoke inhalation and respiratory problems (13.7%). The proportional rates related to falls in VFFs were almost twice the national figures for the same year (39.3% versus 22.3%). County population density was found to be directly associated with injury rates, even when adjusted for number of responses. Claims statistics mirror a similar geographical trend in overall workers' compensation claims for all injuries in West Virginia. The results of this study provide a foundation for additional follow-up studies in order to develop improved occupational safety policies and target educational programs aimed at the prevention of injuries in volunteer fire fighters. Several findings have already resulted in programmatic recommendations.

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

NASA Technical Reports Server (NTRS)

Erickson, Gary E.; Brandon, Jay M.

1987-01-01

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactions of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree of freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

High angle-of-attack aerodynamics of a strake-canard-wing V/STOL fighter configuration

NASA Technical Reports Server (NTRS)

Durston, D. A.; Schreiner, J. A.

1983-01-01

High angle-of-attack aerodynamic data are analyzed for a strake-canard-wing V/STOL fighter configuration. The configuration represents a twin-engine supersonic V/STOL fighter aircraft which uses four longitudinal thrust-augmenting ejectors to provide vertical lift. The data were obtained in tests of a 9.39 percent scale model of the configuration in the NASA Ames 12-Foot Pressure Wind Tunnel, at a Mach number of 0.2. Trimmed aerodynamic characteristics, longitudinal control power, longitudinal and lateral/directional stability, and effects of alternate strake and canard configurations are analyzed. The configuration could not be trimmed (power-off) above 12 deg angle of attack because of the limited pitch control power and the high degree of longitudinal instability (28 percent) at this Mach number. Aerodynamic center location was found to be controllable by varying strake size and canard location without significantly affecting lift and drag. These configuration variations had relatively little effect on the lateral/directional stability up to 10 deg angle of attack.

Perceived aggressiveness predicts fighting performance in mixed-martial-arts fighters.

PubMed

Trebicky, Vít; Havlícek, Jan; Roberts, S Craig; Little, Anthony C; Kleisner, Karel

2013-09-01

Accurate assessment of competitive ability is a critical component of contest behavior in animals, and it could be just as important in human competition, particularly in human ancestral populations. Here, we tested the role that facial perception plays in this assessment by investigating the association between both perceived aggressiveness and perceived fighting ability in fighters' faces and their actual fighting success. Perceived aggressiveness was positively associated with the proportion of fights won, after we controlled for the effect of weight, which also independently predicted perceived aggression. In contrast, perception of fighting ability was confounded by weight, and an association between perceived fighting ability and actual fighting success was restricted to heavyweight fighters. Shape regressions revealed that aggressive-looking faces are generally wider and have a broader chin, more prominent eyebrows, and a larger nose than less aggressive-looking faces. Our results indicate that perception of aggressiveness and fighting ability might cue different aspects of success in male-male physical confrontation.

Pressure breathing in fighter aircraft for G accelerations and loss of cabin pressurization at altitude--a brief review.

PubMed

Lauritzsen, Lars P; Pfitzner, John

2003-04-01

The purpose of this brief review is to outline the past and present use of pressure breathing, not by patients but by fighter pilots. Of the historical and recent references quoted, most are from aviation-medicine journals that are not often readily available to anesthesiologists. Pressure breathing at moderate levels of airway pressure gave World War II fighter pilots a tactical altitude advantage. With today's fast and highly maneuverable jet fighters, very much higher airway pressures of the order of 8.0 kPa (identical with 60 mmHg) are used. They are used in conjunction with a counterpressure thoracic vest and an anti-G suit for the abdomen and lower body. Pressurization is activated automatically in response to +Gz accelerations, and to a potentially catastrophic loss of cabin pressurization at altitude. During +Gz accelerations, pressure breathing has been shown to maintain cerebral perfusion by raising the systemic arterial pressure, so increasing the level of G-tolerance that is afforded by the use of anti-G suits and seat tilt-back angles alone. This leaves the pilot less reliant on rigorous, and potentially distracting, straining maneuvers. With loss of cabin pressurization at altitude, pressure breathing of 100% oxygen at high airway pressures enables the pilot's alveolar PO(2) to be maintained at a safe level during emergency descent. Introduced in military aviation, pressure breathing for G-tolerance and pressure breathing for altitude presented as concepts that may be of general physiological interest to many anesthesiologists.

Unpredictability of fighter pilots' g duration tolerance by anthropometric and physiological characteristics.

PubMed

Park, Myunghwan; Yoo, Seunghoon; Seol, Hyeongju; Kim, Cheonyoung; Hong, Youngseok

2015-04-01

While the factors affecting fighter pilots' G level tolerance have been widely accepted, the factors affecting fighter pilots' G duration tolerance have not been well understood. Thirty-eight subjects wearing anti-G suits were exposed to sustained high G forces using a centrifuge. The subjects exerted AGSM and decelerated the centrifuge when they reached the point of loss of peripheral vision. The G profile consisted of a +2.3 G onset rate, +7.3 G single plateau, and -1.6 G offset rate. Each subject's G tolerance time was recorded and the relationship between the tolerance time and the subject's anthropometric and physiological factors were analyzed. The mean tolerance time of the 38 subjects was 31.6 s, and the min and max tolerance times were 20 s and 58 s, respectively. The correlation analysis indicated that none of the factors had statistically significant correlations with the subjects' G duration tolerance. Stepwise multiple regression analysis showed that G duration tolerance was not dependent on any personal factors of the subjects. After the values of personal factors were simplified into 0 or 1, the t-test analysis showed that subjects' heights were inversely correlated with G duration tolerance at a statistically significant level. However, a logistic regression analysis suggested that the effect of the height factor to a pilot's G duration tolerance was too weak to be used as a predictor of a pilot's G tolerance. Fighter pilots' G duration tolerance could not be predicted by pilots' anthropometric and physiological factors.

Status of development of LCOS projection displays for F-22A, F/A-18E/F, and JSF cockpits

NASA Astrophysics Data System (ADS)

Kalmanash, Michael H.

2001-09-01

Projection display technology has been found to be an attractive alternative to direct view flat panel displays in many avionics applications. The projection approach permits compact high performance systems to be tailored to specific platform needs while using a complement of commercial off the shelf (COTS) components, including liquid crystal on silicon (LCOS) microdisplay imagers. A common projection engine used on multiple platforms enables improved performance, lower cost and shorter development cycles. This paper provides a status update for projection displays under development for the F-22A, the F/A-18E/F and the Lockheed Joint Strike Fighter (JSF) aircraft.

Juncture flow improvement for wing/pylon configurations by using CFD methodology

NASA Technical Reports Server (NTRS)

Gea, Lie-Mine; Chyu, Wei J.; Stortz, Michael W.; Chow, Chuen-Yen

1993-01-01

Transonic flow field around a fighter wing/pylon configuration was simulated by using an implicit upwinding Navier-Stokes flow solver (F3D) and overset grid technology (Chimera). Flow separation and local shocks near the wing/pylon junction were observed in flight and predicted by numerical calculations. A new pylon/fairing shape was proposed to improve the flow quality. Based on numerical results, the size of separation area is significantly reduced and the onset of separation is delayed farther downstream. A smoother pressure gradient is also obtained near the junction area. This paper demonstrates that computational fluid dynamics (CFD) methodology can be used as a practical tool for aircraft design.

The AAF in Northwest Africa. An Account of the Twelfth Air Force in the Northwest African Landing and the Battle for Tunisia

DTIC Science & Technology

1992-01-01

29 echelon of XII Fighter Command; the Moroccan Composite Wing operated in Morocco . All wings were activated 26 January 1943. XII Fighter Command’s...satellites, would raise Allied morale, and would encourage those ele - ments in the Axis-occupied countries which were working as best they could toward...news of the invasion, in order to fore- stall an Allied breaching of the southern coast of France, to establish submarine and air bases , and to control

An Experimental Investigation to Determine the Effect of Speed-Brake Position on the Longitudinal Stability and Trim of a Swept-Wing Fighter Airplane

NASA Technical Reports Server (NTRS)

Taylor, Robert T.

1959-01-01

A 0.10-scale model of a swept-wing fighter airplane was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92 to determine the effects of adding underfuselage speed brakes. The results of brief spoiler-aileron lateral control tests also are included. The tests show acceptable trim and drag increments when the speed brakes are installed at the 32-71-inch fuselage station.

Computer-automated opponent for manned air-to-air combat simulations

NASA Technical Reports Server (NTRS)

Hankins, W. W., III

1979-01-01

Two versions of a real-time digital-computer program that operates a fighter airplane interactively against a human pilot in simulated air combat were evaluated. They function by replacing one of two pilots in the Langley differential maneuvering simulator. Both versions make maneuvering decisions from identical information and logic; they differ essentially in the aerodynamic models that they control. One is very complete, but the other is much simpler, primarily characterizing the airplane's performance (lift, drag, and thrust). Both models competed extremely well against highly trained U.S. fighter pilots.

Effectiveness of brief VR treatment for PTSD in war-fighters: a case study.

PubMed

Miyahira, Sarah D; Folen, Raymond A; Hoffman, Hunter G; Garcia-Palacios, Azucena; Schaper, Kim M

2010-01-01

War-fighters exposed to combat are at high risk for developing posttraumatic stress disorder (PTSD), a complex and challenging condition to treat. Cognitive behavioral therapies (CBT) have been empirically validated as effective treatments for PTSD resulting from sexual assault, vehicular accidents, and disasters. Exposure, imaginal or in vivo, to the traumatic event is a central component of successful CBT treatment. Early studies indicate that CBT with brief virtual reality exposure (VRE) is beneficial in treating PTSD. The case study examined the effectiveness of brief VRE in treating combat-related PTSD.

Design of a V/STOL propulsion system for a large-scale fighter model

NASA Technical Reports Server (NTRS)

Willis, W. S.

1981-01-01

Modifications were made to the existing Large-Scale STOL fighter model to simulate a V/STOL configuration. Modifications include the substitutions of two dimensional lift/cruise exhaust nozzles in the nacelles, and the addition of a third J97 engine in the fuselage to suppy a remote exhaust nozzle simulating a Remote Augmented Lift System. A preliminary design of the inlet and exhaust ducting for the third engine was developed and a detailed design was completed of the hot exhaust ducting and remote nozzle.

F-35 Joint Strike Fighter (JSF) Program: Background, Status, and Issues

DTIC Science & Technology

2007-07-19

Buy ‘Hundreds’ of STOVL Joint Strike Fighters,” Inside the Air Force. September 17, 2004. 6 Marc Selinger. “Jumper Confirms Air Force Plans to Cut...concluded that some 230 of the Navy’s projected buy of 480 JSFs could instead be F/A-18E/Fs, depending on the progress of the JSF program and the price of...18E/F Buy Depends on JSF Progress,’Cohen Tells SASC,” Aerospace Daily, May 21, 1997: 285, 288. See also CRS Issue Brief IB93041, C- 17 Cargo

Indigenous Advanced Fighter Aircraft in Israel: Considerations for Decision-Making.

DTIC Science & Technology

1981-12-01

13 ISO 11,i 30 2 0.2 3.3 1975 924 1029 555 6219 3036 25 255 16.6 33 9 0.4 4.1 1976 969 1022 6311 6676 3164 34 405 IS3 32.3 0.5 6.1 1971 1047... Iso 49 NA 47.1 14 4 NA 30.6 NA 4138 1179 1975 3.5 190 54 NA 54.3 15.4 NA 23.4 NA 4127 1308 1976 3 5 190 57 NA 54.3 16.3 NA 30.0 NA 4087 1337 1977 3.6...357 17400 28266 15200 24692 0. I 1 4 1970 10 15 200 308 19100 29503 18100 27958 0.0 1.1 197 t0 14 ISO 220 21300 31305 20800 30570 0 0 0.7 1972 20

Aircraft geometry verification with enhanced computer generated displays

NASA Technical Reports Server (NTRS)

Cozzolongo, J. V.

1982-01-01

A method for visual verification of aerodynamic geometries using computer generated, color shaded images is described. The mathematical models representing aircraft geometries are created for use in theoretical aerodynamic analyses and in computer aided manufacturing. The aerodynamic shapes are defined using parametric bi-cubic splined patches. This mathematical representation is then used as input to an algorithm that generates a color shaded image of the geometry. A discussion of the techniques used in the mathematical representation of the geometry and in the rendering of the color shaded display is presented. The results include examples of color shaded displays, which are contrasted with wire frame type displays. The examples also show the use of mapped surface pressures in terms of color shaded images of V/STOL fighter/attack aircraft and advanced turboprop aircraft.

X-31 in flight - Post Stall Maneuver

NASA Technical Reports Server (NTRS)

1995-01-01

Two X-31 Enhanced Fighter Maneuverability (EFM) demonstrators were flown at Rockwell International's Palmdale, Calif., facility and the NASA Dryden Flight Research Center, Edwards, Calif., to obtain data that may apply to the design of highly-maneuverable next-generation fighters. The program had its first flight on Oct. 11, 1990, in Palmdale; it ended in June 1995. The X-31 program demonstrated the value of thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems, to provide controlled flight during close-in air combat at very high angles of attack. The result of this increased maneuverability is a significant advantage over conventional fighters. 'Angle-of-attack' (alpha) is an engineering term to describe the angle of an aircraft's body and wings relative to its actual flight path. During maneuvers, pilots often fly at extreme angles of attack -- with the nose pitched up while the aircraft continues in its original direction. This can lead to loss of control and result in the loss of the aircraft, pilot or both. Three thrust vectoring paddles made of graphite epoxy mounted on the X-31's exhaust nozzle directed the exhaust flow to provide control in pitch (up and down) and yaw (right and left) to improve control. The paddles can sustain heat of up to 1,500 degrees centigrade for extended periods of time. In addition the X-31s were configured with movable forward canards and fixed aft strakes. The canards were small wing-like structures set on the wing line between the nose and the leading edge of the wing. The strakes were set on the same line between the trailing edge of the wing and the engine exhaust. Both supplyied additional control in tight maneuvering situations. The X-31 research program produced technical data at high angles of attack. This information is giving engineers and aircraft designers a better understanding of aerodynamics, effectiveness of flight controls and thrust vectoring, and airflow phenomena at high angles of attack. This is expected to lead to design methods providing better maneuverability in future high performance aircraft and make them safer to fly. An international test organization of about 110 people, managed by the Advanced Research Projects Agency (ARPA), conducted the flight operations at Dryden, to which flight research was moved in February 1992 at the request of the Advanced Research Projects Agency (ARPA). In addition to ARPA and NASA, the International Test Organization (ITO) included the U.S. Navy, the U.S. Air Force, Rockwell International, the Federal Republic of Germany, and Daimler-Benz Aerospace (formerly Messerschmitt-Bolkow-Blohm and Deutsche Aerospace). NASA was responsible for flight research operations, aircraft maintenance, and research engineering once the program moved to Dryden. The No. 1 X-31 aircraft was lost in an accident Jan. 19, 1995. The pilot, Karl Heinz-Lang, of the Federal Republic of Germany, ejected safely before the aircraft crashed in an unpopulated desert area just north of Edwards. The X-31 program logged an X-plane record of 580 flights during the program, including 555 research missions and 21 in Europe for the 1995 Paris Air Show. A total of 14 pilots representing all agencies of the ITO flew the aircraft. This 34-second movie clip shows the aircraft as it slides backwards, thrust vectoring the tail over the top, turning the stall into a loop in which the aircraft then reverses it's heading and resumes level flight.

On-board fault diagnostics for fly-by-light flight control systems using neural network flight processors

NASA Astrophysics Data System (ADS)

Urnes, James M., Sr.; Cushing, John; Bond, William E.; Nunes, Steve

1996-10-01

Fly-by-Light control systems offer higher performance for fighter and transport aircraft, with efficient fiber optic data transmission, electric control surface actuation, and multi-channel high capacity centralized processing combining to provide maximum aircraft flight control system handling qualities and safety. The key to efficient support for these vehicles is timely and accurate fault diagnostics of all control system components. These diagnostic tests are best conducted during flight when all facts relating to the failure are present. The resulting data can be used by the ground crew for efficient repair and turnaround of the aircraft, saving time and money in support costs. These difficult to diagnose (Cannot Duplicate) fault indications average 40 - 50% of maintenance activities on today's fighter and transport aircraft, adding significantly to fleet support cost. Fiber optic data transmission can support a wealth of data for fault monitoring; the most efficient method of fault diagnostics is accurate modeling of the component response under normal and failed conditions for use in comparison with the actual component flight data. Neural Network hardware processors offer an efficient and cost-effective method to install fault diagnostics in flight systems, permitting on-board diagnostic modeling of very complex subsystems. Task 2C of the ARPA FLASH program is a design demonstration of this diagnostics approach, using the very high speed computation of the Adaptive Solutions Neural Network processor to monitor an advanced Electrohydrostatic control surface actuator linked through a AS-1773A fiber optic bus. This paper describes the design approach and projected performance of this on-line diagnostics system.

Centrifuge-induced neck and back pain in F-16 pilots: a report of four cases.

PubMed

Lange, Britt; Nielsen, René Tyranski; Skejø, Pernille Bro; Toft, Palle

2013-07-01

Early in their careers, as an important part of their training to become fighter pilots, pilots undergo centrifuge training in order to learn effective anti-G straining maneuvers (AGSM) and to test their G tolerance. The exposure of pilots, especially early in their careers, to training that could lead to injuries should be avoided. This is a report of four cases of neck pain experienced during G-tolerance training, some of which may have caused ongoing problems for the pilot. Four cases, describing four different injuries experienced during G-tolerance training, are presented, including the history of the incident, radiographic description, and physical examination. Three main questions were identified in regards to the training of fighter pilots in centrifuges: 1) should the seat be positioned to imitate a specific aircraft's seat? 2) should the pilot wear a helmet and a mask? 3) what is the appropriate amount of head support? Based on the four cases reported it is recommended that pilots should be given the best possible conditions concerning neck support and load on the neck and the back for G-tolerance testing. Training the pilot in an anatomical neutral sitting position, without a helmet, and with maximal neck support minimizes head movements in cases of conscious or unconscious loss of muscle control. To test the stability of the neck in a setup similar to the environment where the pilot is going to operate, the pilot should be given the opportunity to prepare himself or herself accordingly in advance.

An investigation of fighter aircraft agility

NASA Technical Reports Server (NTRS)

Valasek, John; Downing, David R.

1993-01-01

This report attempts to unify in a single document the results of a series of studies on fighter aircraft agility funded by the NASA Ames Research Center, Dryden Flight Research Facility and conducted at the University of Kansas Flight Research Laboratory during the period January 1989 through December 1993. New metrics proposed by pilots and the research community to assess fighter aircraft agility are collected and analyzed. The report develops a framework for understanding the context into which the various proposed fighter agility metrics fit in terms of application and testing. Since new metrics continue to be proposed, this report does not claim to contain every proposed fighter agility metric. Flight test procedures, test constraints, and related criteria are developed. Instrumentation required to quantify agility via flight test is considered, as is the sensitivity of the candidate metrics to deviations from nominal pilot command inputs, which is studied in detail. Instead of supplying specific, detailed conclusions about the relevance or utility of one candidate metric versus another, the authors have attempted to provide sufficient data and analyses for readers to formulate their own conclusions. Readers are therefore ultimately responsible for judging exactly which metrics are 'best' for their particular needs. Additionally, it is not the intent of the authors to suggest combat tactics or other actual operational uses of the results and data in this report. This has been left up to the user community. Twenty of the candidate agility metrics were selected for evaluation with high fidelity, nonlinear, non real-time flight simulation computer programs of the F-5A Freedom Fighter, F-16A Fighting Falcon, F-18A Hornet, and X-29A. The information and data presented on the 20 candidate metrics which were evaluated will assist interested readers in conducting their own extensive investigations. The report provides a definition and analysis of each metric; details of how to test and measure the metric, including any special data reduction requirements; typical values for the metric obtained using one or more aircraft types; and a sensitivity analysis if applicable. The report is organized as follows. The first chapter in the report presents a historical review of air combat trends which demonstrate the need for agility metrics in assessing the combat performance of fighter aircraft in a modern, all-aspect missile environment. The second chapter presents a framework for classifying each candidate metric according to time scale (transient, functional, instantaneous), further subdivided by axis (pitch, lateral, axial). The report is then broadly divided into two parts, with the transient agility metrics (pitch lateral, axial) covered in chapters three, four, and five, and the functional agility metrics covered in chapter six. Conclusions, recommendations, and an extensive reference list and biography are also included. Five appendices contain a comprehensive list of the definitions of all the candidate metrics; a description of the aircraft models and flight simulation programs used for testing the metrics; several relations and concepts which are fundamental to the study of lateral agility; an in-depth analysis of the axial agility metrics; and a derivation of the relations for the instantaneous agility and their approximations.

AFTI/F-16 Air probe close-up

NASA Technical Reports Server (NTRS)

1982-01-01

This close-up view shows the AFTI F-16 air probe early in the research program. It consists of a nose boom resembling a long pipe, and four indicators that look and act like weather vanes. The indicators on the left and right measure pitch, or the movement of the airplane's nose up or down. Those on the top and bottom of the boom measure yaw, or movement of the nose to the left or right. Similar probes are standard on most research and prototype aircraft. The data from the indicators is recorded aboard the aircraft and/or radioed to the ground. This data includes both the amount of yaw and pitch at any given time, and the rate at which both motions changed in flight. This information, subsequently processed and compared to wind tunnel results, may reveal stability and aerodynamic abnormalities. The two metal half-circles and their attachment fixtures are not part of the air probe. Rather, they are used to calibrate the indicators on the ground, enabling the data to be corrected for instrument errors. The figure in the photograph is shown holding a red 'Remove Before Flight' ribbon, a reminder to the ground crew that it must be taken off prior to a research mission. During the 1980s and 1990s, NASA and the U.S. Air Force participated in a joint program to integrate and demonstrate new avionics technologies to improve close air support capabilities in next-generation aircraft. The testbed aircraft, seen here in flight over the desert at NASA's Dryden Flight Research Center, Edwards, California, was called the Advanced Fighter Technology Integration (AFTI) F-16. The tests demonstrated technologies to improve navigation and the pilot's ability to find and destroy enemy ground targets day or night, including adverse weather. The aircraft--an F-16A Fighting Falcon (Serial #75-0750)--underwent numerous modifications. A relatively low-cost testbed, it evaluated the feasability of advanced, intergrated-sensor, avionics, and flight control technologies. During the first phase of the AFTI/F-16 program, which began in 1983, the aircraft demonstrated voice-actuated commands, helmet-mounted sights, flat turns, and selective fuselage pointing using forward-mounted canards and a triplex digital flight control computer system. The second phase of research, which began in the summer of 1991, demonstrated advanced technologies and capabilities to find and destroy ground targets day or night, and in adverse weather while using maneuverability and speed at low altitude. This phase was known as the close air support and battlefield air interdiction (CAS/BAI) phase. Finally, the aircraft was used to assess the Automatic Ground Collision Avoidance System (Auto - GCAS), a joint project with the Swedish Government. For these tests, the pilot flew the aircraft directly toward the ground, simulating a total loss of control. The GCAS was designed to take command in such emergencies and bring the aircraft back to level flight. The AFTI F-16 program ended at Dryden on November 4, 1997 after 15 years and over 700 research flights. The USAF continued to fly the aircraft until retiring it to the Air Force Museum on January 9, 2001.

Evaluation of helmet-mounted display targeting symbology based on eye tracking technology

NASA Astrophysics Data System (ADS)

Wang, Lijing; Wen, Fuzhen; Ma, Caixin; Zhao, Shengchu; Liu, Xiaodong

2014-06-01

The purpose of this paper is to find the Target Locator Lines (TLLs) which perform best by contrasting and comparing experiment based on three kinds of TTLs of fighter HMD. 10 university students, male, with an average age of 21-23, corrected visual acuity 1.5, participated in the experiment. In the experiment, head movement data was obtained by TrackIR. The geometric relationship between the coordinates of the real world and coordinates of the visual display was obtained by calculating the distance from viewpoint to midpoint of both eyes and the head movement data. Virtual helmet system simulation experiment environment was created by drawing TLLs of fighter HMD in the flight simulator visual scene. In the experiment, eye tracker was used to record the time and saccade trajectory. The results were evaluated by the duration of the time and saccade trajectory. The results showed that the symbol"locator line with digital vector length indication" cost most time and had the longest length of the saccade trajectory. It is the most ineffective and most unacceptable way. "Locator line with extending head vector length symbol" cost less time and had less length of the saccade trajectory. It is effective and acceptable;"Locator line with reflected vector length symbol" cost the least time and had the least length of the saccade trajectory. It is the most effective and most acceptable way. "Locator line with reflected vector length symbol" performs best. The results will provide reference value for the research of TTLs in future.

Taekwondo Fighting in Training Does Not Simulate the Affective and Cognitive Demands of Competition: Implications for Behavior and Transfer.

PubMed

Maloney, Michael A; Renshaw, Ian; Headrick, Jonathon; Martin, David T; Farrow, Damian

2018-01-01

Enhancing practice design is critical to facilitate transfer of learning. Considerable research has focused on the role of perceptual information in practice simulation, yet has neglected how affect and cognition are shaped by practice environments and whether this influences the fidelity of behavior (Headrick et al., 2015). This study filled this gap by examining the fidelity of individual (cognition, affect, and actions) and interpersonal behavior of 10 highly skilled Australian Taekwondo athletes fighting in training compared to competition. Interpersonal behavior was assessed by tracking location coordinates to analyze distance-time coordination tendencies of the fighter-fighter system. Individual actions were assessed through notational analysis and approximate entropy calculations of coordinate data to quantify the (un)predictability of movement displacement. Affect and cognition were assessed with mixed-methods that included perceptual scales measuring anxiety, arousal, and mental effort, and post-fight video-facilitated confrontational interviews to explore how affect and cognitions might differ. Quantitative differences were assessed with mixed models and dependent t -tests. Results reveal that individual and interpersonal behavior differed between training and competition. In training, individuals attacked less ( d = 0.81, p < 0.05), initiated attacks from further away ( d = -0.20, p < 0.05) and displayed more predictable movement trajectories ( d = 0.84, p < 0.05). In training, fighters had lower anxiety ( d = -1.26, p < 0.05), arousal ( d = -1.07, p < 0.05), and mental effort ( d = -0.77, p < 0.05). These results were accompanied by changes in interpersonal behavior, with larger interpersonal distances generated by the fighter-fighter system in training ( d = 0.80, p < 0.05). Qualitative data revealed the emergence of cognitions and affect specific to the training environment, such as reductions in pressure, arousal, and mental challenge. Findings highlight the specificity of performer-environment interactions. Fighting in training affords reduced affective and cognitive demands and a decrease in action fidelity compared to competition. In addition to sampling information, representative practice needs to consider modeling the cognitions and affect of competition to enhance transfer.

Incidence of injury in professional mixed martial arts competitions.

PubMed

Bledsoe, Gregory H; Hsu, Edbert B; Grabowski, Jurek George; Brill, Justin D; Li, Guohua

2006-01-01

Mixed Martial Arts (MMA) competitions were introduced in the United States with the first Ultimate Fighting Championship (UFC) in 1993. In 2001, Nevada and New Jersey sanctioned MMA events after requiring a series of rule changes. The purpose of this study was to determine the incidence of injury in professional MMA fighters. Data from all professional MMA events that took place between September 2001 and December 2004 in the state of Nevada were obtained from the Nevada Athletic Commission. Medical and outcome data from events were analyzed based on a pair-matched case-control design. Both conditional and unconditional logistic regression models were used to assess risk factors for injury. A total of 171 MMA matches involving 220 different fighters occurred during the study period. There were a total of 96 injuries to 78 fighters. Of the 171 matches fought, 69 (40.3%) ended with at least one injured fighter. The overall injury rate was 28.6 injuries per 100 fight participations or 12.5 injuries per 100 competitor rounds. Facial laceration was the most common injury accounting for 47.9% of all injuries, followed by hand injury (13.5%), nose injury (10.4%), and eye injury (8.3%). With adjustment for weight and match outcome, older age was associated with significantly increased risk of injury. The most common conclusion to a MMA fight was a technical knockout (TKO) followed by a tap out. The injury rate in MMA competitions is compatible with other combat sports involving striking. The lower knockout rates in MMA compared to boxing may help prevent brain injury in MMA events. Key PointsMixed martial arts (MMA) has changed since the first MMA matches in the United States and now has increased safety regulations and sanctioning.MMA competitions have an overall high rate of injury.There have been no MMA deaths in the United States.The knockout (KO) rate in MMA appears to be lower than the KO rate of boxing matches.MMA must continue to be supervised by properly trained medical professionals and referees to ensure fighter safety in the future.

Violence against women during the Liberian civil conflict.

PubMed

Swiss, S; Jennings, P J; Aryee, G V; Brown, G H; Jappah-Samukai, R M; Kamara, M S; Schaack, R D; Turay-Kanneh, R S

1998-02-25

Civilians were often the casualties of fighting during the recent Liberian civil conflict. Liberian health care workers played a crucial role in documenting violence against women by soldiers and fighters during the war. To document women's experiences of violence, including rape and sexual coercion, from a soldier or fighter during 5 years of the Liberian civil war from 1989 through 1994. Interview and survey. High schools, markets, displaced persons camps, and urban communities in Monrovia, Liberia, in 1994. A random sample of 205 women and girls between the ages of 15 and 70 years (88% participation rate). One hundred (49%) of 205 participants reported experiencing at least 1 act of physical or sexual violence by a soldier or fighter. Survey participants reported being beaten, tied up, or detained in a room under armed guard (17%); strip-searched 1 or more times (32%); and raped, subjected to attempted rape, or sexually coerced (15%). Women who were accused of belonging to a particular ethnic group or fighting faction or who were forced to cook for a soldier or fighter were at increased risk for physical and sexual violence. Of the 106 women and girls accused of belonging to an ethnic group or faction, 65 (61%) reported that they were beaten, locked up, strip-searched, or subjected to attempted rape, compared with 27 (27%) of the 99 women who were not accused (P< or =.02, .07, .001, and .06, respectively). Women and girls who were forced to cook for a soldier or fighter were more likely to report experiencing rape, attempted rape, or sexual coercion than those who were not forced to cook (55% vs 10%; P< or =.001, .06, and .001, respectively). Young women (those younger than 25 years) were more likely than women 25 years or older to report experiencing attempted rape and sexual coercion (18% vs 4%, P=.02 and .04, respectively). This collaborative research allowed Liberian women to document wartime violence against women in their own communities and to develop a unique program to address violence against women in Liberia.

Incidence of Injury in Professional Mixed Martial Arts Competitions

PubMed Central

Bledsoe, Gregory H.; Hsu, Edbert B.; Grabowski, Jurek George; Brill, Justin D.; Li, Guohua

2006-01-01

Mixed Martial Arts (MMA) competitions were introduced in the United States with the first Ultimate Fighting Championship (UFC) in 1993. In 2001, Nevada and New Jersey sanctioned MMA events after requiring a series of rule changes. The purpose of this study was to determine the incidence of injury in professional MMA fighters. Data from all professional MMA events that took place between September 2001 and December 2004 in the state of Nevada were obtained from the Nevada Athletic Commission. Medical and outcome data from events were analyzed based on a pair-matched case-control design. Both conditional and unconditional logistic regression models were used to assess risk factors for injury. A total of 171 MMA matches involving 220 different fighters occurred during the study period. There were a total of 96 injuries to 78 fighters. Of the 171 matches fought, 69 (40.3%) ended with at least one injured fighter. The overall injury rate was 28.6 injuries per 100 fight participations or 12.5 injuries per 100 competitor rounds. Facial laceration was the most common injury accounting for 47.9% of all injuries, followed by hand injury (13.5%), nose injury (10.4%), and eye injury (8.3%). With adjustment for weight and match outcome, older age was associated with significantly increased risk of injury. The most common conclusion to a MMA fight was a technical knockout (TKO) followed by a tap out. The injury rate in MMA competitions is compatible with other combat sports involving striking. The lower knockout rates in MMA compared to boxing may help prevent brain injury in MMA events. Key Points Mixed martial arts (MMA) has changed since the first MMA matches in the United States and now has increased safety regulations and sanctioning. MMA competitions have an overall high rate of injury. There have been no MMA deaths in the United States. The knockout (KO) rate in MMA appears to be lower than the KO rate of boxing matches. MMA must continue to be supervised by properly trained medical professionals and referees to ensure fighter safety in the future. PMID:24357986

Fighter pilots' heart rate, heart rate variation and performance during instrument approaches.

PubMed

Mansikka, Heikki; Simola, Petteri; Virtanen, Kai; Harris, Don; Oksama, Lauri

2016-10-01

Fighter pilots' heart rate (HR), heart rate variation (HRV) and performance during instrument approaches were examined. The subjects were required to fly instrument approaches in a high-fidelity simulator under various levels of task demand. The task demand was manipulated by increasing the load on the subjects by reducing the range at which they commenced the approach. HR and the time domain components of HRV were used as measures of pilot mental workload (PMWL). The findings of this study indicate that HR and HRV are sensitive to varying task demands. HR and HRV were able to distinguish the level of PMWL after which the subjects were no longer able to cope with the increasing task demands and their instrument landing system performance fell to a sub-standard level. The major finding was the HR/HRV's ability to differentiate the sub-standard performance approaches from the high-performance approaches. Practitioner Summary: This paper examined if HR and HRV were sensitive to varying task demands in a fighter aviation environment and if these measures were related to variations in pilot's performance.

Physiological parameters monitoring of fire-fighters by means of a wearable wireless sensor system

NASA Astrophysics Data System (ADS)

Stelios, M.; Mitilineos, Stelios A.; Chatzistamatis, Panagiotis; Vassiliadis, Savvas; Primentas, Antonios; Kogias, Dimitris; Michailidis, Emmanouel T.; Rangoussi, Maria; Kurşun Bahadir, Senem; Atalay, Özgür; Kalaoğlu, Fatma; Sağlam, Yusuf

2016-03-01

Physiological parameter monitoring may be useful in many different groups of the population, such as infants, elderly people, athletes, soldiers, drivers, fire-fighters, police etc. This can provide a variety of information ranging from health status to operational readiness. In this article, we focus on the case of first responders and specifically fire-fighters. Firefighters can benefit from a physiological monitoring system that is used to extract multiple indications such as the present position, the possible life risk level, the stress level etc. This work presents a wearable wireless sensor network node, based on low cost, commercial-off- the-self (COTS) electronic modules, which can be easily attached on a standard fire-fighters’ uniform. Due to the low frequency wired interface between the selected electronic components, the proposed solution can be used as a basis for a textile system where all wired connections will be implemented by means of conductive yarn routing in the textile structure, while some of the standard sensors can be replaced by textile ones. System architecture is described in detail, while indicative samples of acquired signals are also presented.

Utilization of an agility assessment module in analysis and optimization of preliminary fighter configuration

NASA Technical Reports Server (NTRS)

Ngan, Angelen; Biezad, Daniel

1996-01-01

A study has been conducted to develop and to analyze a FORTRAN computer code for performing agility analysis on fighter aircraft configurations. This program is one of the modules of the NASA Ames ACSYNT (AirCraft SYNThesis) design code. The background of the agility research in the aircraft industry and a survey of a few agility metrics are discussed. The methodology, techniques, and models developed for the code are presented. The validity of the existing code was evaluated by comparing with existing flight test data. A FORTRAN program was developed for a specific metric, PM (Pointing Margin), as part of the agility module. Example trade studies using the agility module along with ACSYNT were conducted using a McDonnell Douglas F/A-18 Hornet aircraft model. Tile sensitivity of thrust loading, wing loading, and thrust vectoring on agility criteria were investigated. The module can compare the agility potential between different configurations and has capability to optimize agility performance in the preliminary design process. This research provides a new and useful design tool for analyzing fighter performance during air combat engagements in the preliminary design.

Development of an agility assessment module for preliminary fighter design

NASA Technical Reports Server (NTRS)

Ngan, Angelen; Bauer, Brent; Biezad, Daniel; Hahn, Andrew

1996-01-01

A FORTRAN computer program is presented to perform agility analysis on fighter aircraft configurations. This code is one of the modules of the NASA Ames ACSYNT (AirCraft SYNThesis) design code. The background of the agility research in the aircraft industry and a survey of a few agility metrics are discussed. The methodology, techniques, and models developed for the code are presented. FORTRAN programs were developed for two specific metrics, CCT (Combat Cycle Time) and PM (Pointing Margin), as part of the agility module. The validity of the code was evaluated by comparing with existing flight test data. Example trade studies using the agility module along with ACSYNT were conducted using Northrop F-20 Tigershark and McDonnell Douglas F/A-18 Hornet aircraft models. The sensitivity of thrust loading and wing loading on agility criteria were investigated. The module can compare the agility potential between different configurations and has the capability to optimize agility performance in the preliminary design process. This research provides a new and useful design tool for analyzing fighter performance during air combat engagements.

The southpaw advantage? Lateral preference in mixed martial arts.

PubMed

Baker, Joseph; Schorer, Jörg

2013-01-01

Performers with a left-orientation have a greater likelihood of obtaining elite levels of performance in many interactive sports. This study examined whether combat stance orientation was related to skill and success in Mixed Martial Arts fighters. Data were extracted for 1468 mixed martial artists from a reliable and valid online data source. Measures included fighting stance, win percentage and an ordinal measure of skill based on number of fights. The overall analysis revealed that the fraction of fighters using a southpaw stance was greater than the fraction of left-handers in the general population, but the relationship between stance and hand-preference is not well-understood. Furthermore, t-tests found no statistically significant relationship between laterality and winning percentage, although there was a significant difference between stances for number of fights. Southpaw fighters had a greater number of fights than those using an orthodox stance. These results contribute to an expanding database on the influence of laterality on sport performance and a relatively limited database on variables associated with success in mixed martial arts.

Evaluation of pressure and thermal data from a wind tunnel test of a large-scale, powered, STOL fighter model

NASA Technical Reports Server (NTRS)

Howell, G. A.; Crosthwait, E. L.; Witte, M. C.

1981-01-01

A STOL fighter model employing the vectored-engine-over wing concept was tested at low speeds in the NASA/Ames 40 by 80-foot wind tunnel. The model, approximately 0.75 scale of an operational fighter, was powered by two General Electric J-97 turbojet engines. Limited pressure and thermal instrumentation were provided to measure power effects (chordwise and spanwise blowing) and control-surface-deflection effects. An indepth study of the pressure and temperature data revealed many flow field features - the foremost being wing and canard leading-edge vortices. These vortices delineated regions of attached and separated flow, and their movements were often keys to an understanding of flow field changes caused by power and control-surface variations. Chordwise blowing increased wing lift and caused a modest aft shift in the center of pressure. The induced effects of chordwise blowing extended forward to the canard and significantly increased the canard lift when the surface was stalled. Spanwise blowing effectively enhanced the wing leading-edge vortex, thereby increasing lift and causing a forward shift in the center of pressure.

The lived experience of men with advanced cancer in relation to their perceptions of masculinity: a qualitative phenomenological study.

PubMed

Stapleton, Sarah; Pattison, Natalie

2015-04-01

The aim of this exploratory research was to understand how men experience their advanced cancer in relation to their perceptions of masculinity. There are differences in the way men and women experience illness and health care. There are inequalities in incidence and morbidities of many diseases as well as differences in rates of help-seeking behaviours. Theories on masculinity offer some explanation towards this. Men's experiences of advanced cancer in relation to masculinity are under reported, published literature suggests that there are certain issues or men dealing with advanced disease that justify investigation. A Qualitative approach using a Husserlian Phenomenological design was conducted. Eight men (aged 26-68) all with advanced cancer, defined as advanced or metastatic disease for which the patient had exhausted all standard therapeutic options. In-depth interviews were conducted to capture narratives of the experiences of men. Data were analysed using Colaizzi's seven stage framework. Themes included thwarted ambition, changing expectations, protection and provision, stoicism and coping, images of illness versus images of masculinity, importance of being a fighter and loss. Findings showed that the experiences of these men were complex and should be handled sensitively. Ideas for gender-specific interventions and further research were developed from the findings in relation to current literature. A better understanding and awareness of this in this context will help nurses to consider more subtle challenges that these patients may be dealing with that in turn could affect how they cope with the burden of cancer. © 2014 John Wiley & Sons Ltd.

Air National Guard Fighters the Total Force (Maxwell Paper, Number 1)

DTIC Science & Technology

1996-05-01

child abuse cases, 9 percent rise in spousal abuse reports, and an 11 percent rise in alcohol abuse. While these figures represent only one fighter wing, they highlight some of the potential problems that may be encountered by other active duty units as they too struggle under an ever increasing workload. These problems and a growing belief that long-term readiness may soon suffer if the workload is not reduced, convinced Defense Secretary William Perry to direct a greater role for the Air National Guard in peacetime contingency operations. The Air National Guard is no

Subsonic characteristics of a twin-jet swept-wing fighter model with maneuvering devices

NASA Technical Reports Server (NTRS)

Ray, E. J.; Hollingsworth, E. G.

1973-01-01

An investigation has been conducted at Mach numbers ranging from 0.06 to 0.94 to determine the effects of various combinations of leading-edge slat devices on the static aerodynamic characteristics of a twin-jet swept-wing fighter model. The study also included a determination of the effects of wing leading-edge droop, trailing-edge chord-extensions, wing fences, and wing-planform and camber modifications. The angle-of-attack range generally extended from about minus 2 deg to 24 deg and the sideslip angles ranged from about minus 6 deg to 13 deg.

McDonald XP-85 Airplane in 40x80 foot Wind Tunnel.

NASA Image and Video Library

1948-04-08

Front View of McDonald XP-85 Plan Model. Parasite Airplane designed to be carried in the B-36 bombay (never built) At the time it was the smallest Jet powered airplane. The McDonnell XF-85 Goblin was an American prototype fighter aircraft conceived during World War II by McDonnell Aircraft. It was intended to be deployed from the bomb bay of the giant Convair B-36 bomber as a parasite fighter. The XF-85's intended role was to defend bombers from hostile interceptor aircraft, a need demonstrated during World War II

Subsonic and supersonic aerodynamic characteristics of a supersonic cruise fighter model with a twisted and cambered wing with 74 deg sweep

NASA Technical Reports Server (NTRS)

Morris, O. A.

1977-01-01

A wind tunnel investigation has been conducted to determine the longitudinal and lateral aerodynamic characteristics of a model of a supersonic cruise fighter configuration with a design Mach number of 2.60. The configuration is characterized by a highly swept arrow wing twisted and cambered to minimize supersonic drag due to lift, twin wing mounted vertical tails, and an aft mounted integral underslung duel-engine pod. The investigation also included tests of the configuration with larger outboard vertical tails and with small nose strakes.

Measurement and Analysis of Wing and Tail Buffeting Loads on a Fighter Airplane

NASA Technical Reports Server (NTRS)

Huston, Wilber B; Skopinski, T H

1955-01-01

The buffeting loads measured on the wing and tail of a fighter airplane during 194 maneuvers are given in tabular form, along with the associated flight conditions. Measurements were made at altitudes of 30,000 to 10,000 feet and at speeds up to a Mach number of 0.8. Least-squares methods have been used for a preliminary analysis of the data. The agreement between the results of this analysis and the loads measured in stalls is sufficiently good to suggest the examination of the buffeting of other airplanes on the same basis.

Water-tunnel investigation of concepts for alleviation of adverse inlet spillage interactions with external stores

NASA Technical Reports Server (NTRS)

Neuhart, Dan H.; Rhode, Matthew N.

1990-01-01

A test was conducted in the NASA Langley 16- by 24-Inch Water Tunnel to study alleviation of the adverse interactions of inlet spillage flow on the external stores of a fighter aircraft. A 1/48-scale model of a fighter aircraft was used to simulate the flow environment around the aircraft inlets and on the downstream underside of the fuselage. A controlled inlet mass flow was simulated by drawing water into the inlets. Various flow control devices were used on the underside of the aircraft model to manipulate the vortical inlet spillage flow.

Vortex Flap Technology: a Stability and Control Assessment

NASA Technical Reports Server (NTRS)

Carey, K. M.; Erickson, G. E.

1984-01-01

A comprehensive low-speed wind tunnel investigation was performed of leading edge vortex flaps applied to representative aircraft configurations. A determination was made of the effects of analytically- and empirically-designed vortex flaps on the static longitudinal and lateral-directional aerodynamics, stability, and control characteristics of fighter wings having leading-edge sweep angles of 45 to 76.5 degrees. The sensitivity to several configuration modifications was assessed, which included the effects of flap planform, leading- and trailing-edge flap deflection angles, wing location on the fuselage, forebody strakes, canards, and centerline and outboard vertical tails. Six-component forces and moments, wing surface static pressure distributions, and surface flow patterns were obtained using the Northrop 21- by 30-inch low-speed wind tunnel.

Aircraft Design Software

NASA Technical Reports Server (NTRS)

1997-01-01

Successful commercialization of the AirCraft SYNThesis (ACSYNT) tool has resulted in the creation of Phoenix Integration, Inc. ACSYNT has been exclusively licensed to the company, an outcome of a seven year, $3 million effort to provide unique software technology to a focused design engineering market. Ames Research Center formulated ACSYNT and in working with the Virginia Polytechnic Institute CAD Laboratory, began to design and code a computer-aided design for ACSYNT. Using a Joint Sponsored Research Agreement, Ames formed an industry-government-university alliance to improve and foster research and development for the software. As a result of the ACSYNT Institute, the software is becoming a predominant tool for aircraft conceptual design. ACSYNT has been successfully applied to high- speed civil transport configuration, subsonic transports, and supersonic fighters.

Designing and Managing Successful International Joint Development Programs

DTIC Science & Technology

2016-04-30

Åèìáëáíáçå=oÉëÉ~êÅÜ=mêçÖê~ã= dê~Çì~íÉ=pÅÜççä=çÑ=_ìëáåÉëë=C=mìÄäáÅ=mçäáÅó= k~î~ä=mçëíÖê~Çì~íÉ=pÅÜççä= SYM-AM- 16 -070 mêçÅÉÉÇáåÖë= çÑ=íÜÉ...acquisition issues. He derives knowledge from complex data collections via succinct and innovative tables, charts, and maps . His recent research...attack aircraft and the Air Force’s F- 16 Fighting Falcon multirole fighter. Two years later, an advanced short takeoff and vertical landing (ASTOVL

Recent Events in Guidance, Navigation and Control

NASA Technical Reports Server (NTRS)

Polites, Michael E.; Bullman, Jack (Technical Monitor)

2001-01-01

This article summarizes recent events in Guidance, Navigation, and Control (GN&C) in space, weapons and missiles, and aircraft. The section on space includes recent developments with the following NASA spacecraft and space vehicles: Near Earth Asteroid Rendezvous, Deep Space 1, Microwave Anisotropy Probe, Earth Observer-1, Compton Gamma Ray Observatory, the International Space Station, X-38, and X-40A. The section on weapons and missiles includes recent developments with the following missiles: Joint Air-to-Surface Standoff Missile, Storm Shadow/Scalp EG precision standoff missile, Hellfire missile, AIM-120C Advanced medium-range air-to-air missile, Derby missile, Arrow 2, and the Standard Missile SM-3. The section on aircraft includes recent developments with the following aircraft: Joint Strike Fighter, X-31, V-22, Couger/SUDer Puma Mk. 2, Predator B 001, and the Unmanned Combat Air Vehicle.

Simulation model of the integrated flight/propulsion control system, displays, and propulsion system for ASTOVL lift-fan aircraft

NASA Technical Reports Server (NTRS)

Chung, W. Y. William; Borchers, Paul F.; Franklin, James A.

1995-01-01

A simulation model has been developed for use in piloted evaluations of takeoff, transition, hover, and landing characteristics of an advanced, short takeoff, vertical landing lift fan fighter aircraft. The flight/propulsion control system includes modes for several response types which are coupled to the aircraft's aerodynamic and propulsion system effectors through a control selector tailored to the lift fan propulsion system. Head-up display modes for approach and hover, tailored to their corresponding control modes are provided in the simulation. Propulsion system components modeled include a remote lift and a lift/cruise engine. Their static performance and dynamic response are represented by the model. A separate report describes the subsonic, power-off aerodynamics and jet induced aerodynamics in hover and forward flight, including ground effects.

Aerodynamics model for a generic ASTOVL lift-fan aircraft

NASA Technical Reports Server (NTRS)

Birckelbaw, Lourdes G.; Mcneil, Walter E.; Wardwell, Douglas A.

1995-01-01

This report describes the aerodynamics model used in a simulation model of an advanced short takeoff and vertical landing (ASTOVL) lift-fan fighter aircraft. The simulation model was developed for use in piloted evaluations of transition and hover flight regimes, so that only low speed (M approximately 0.2) aerodynamics are included in the mathematical model. The aerodynamic model includes the power-off aerodynamic forces and moments and the propulsion system induced aerodynamic effects, including ground effects. The power-off aerodynamics data were generated using the U.S. Air Force Stability and Control Digital DATCOM program and a NASA Ames in-house graphics program called VORVIEW which allows the user to easily analyze arbitrary conceptual aircraft configurations using the VORLAX program. The jet-induced data were generated using the prediction methods of R. E. Kuhn et al., as referenced in this report.

In-flight thrust determination on a real-time basis

NASA Technical Reports Server (NTRS)

Ray, R. J.; Carpenter, T.; Sandlin, T.

1984-01-01

A real time computer program was implemented on a F-15 jet fighter to monitor in-flight engine performance of a Digital Electronic Engine Controlled (DEES) F-100 engine. The application of two gas generator methods to calculate in-flight thrust real time is described. A comparison was made between the actual results and those predicted by an engine model simulation. The percent difference between the two methods was compared to the predicted uncertainty based on instrumentation and model uncertainty and agreed closely with the results found during altitude facility testing. Data was obtained from acceleration runs of various altitudes at maximum power settings with and without afterburner. Real time in-flight thrust measurement was a major advancement to flight test productivity and was accomplished with no loss in accuracy over previous post flight methods.

Laser velocimetry in highly three-dimensional and vortical flows

NASA Technical Reports Server (NTRS)

Novak, C. J.; Huie, C. R.; Cornelius, K. C.

1986-01-01

The need for experimentally determined 3-D velocity information is crucial to the understanding of highly 3-dimensional and vortical flow fields. In addition to gaining an understanding of the physics of flow fields, a correlation of velocity data is needed for advanced computational modelling. A double pass method for acquiring 3-D flow field information using a 2-D laser velocimeter (LV) is described. The design and implementation of a 3-D LV with expanded capabilities to acquire real-time 3-D flow field information are also described. Finally, the use of such an instrument in a wind tunnel study of a generic fighter configuration is described. The results of the wind tunnel study highlight the complexities of 3-D flow fields, particularly when the vortex behavior is examined over a range of angles of attack.

A Control Law Design Method Facilitating Control Power, Robustness, Agility, and Flying Qualities Tradeoffs: CRAFT

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.; Davidson, John B.

1998-01-01

A multi-input, multi-output control law design methodology, named "CRAFT", is presented. CRAFT stands for the design objectives addressed, namely, Control power, Robustness, Agility, and Flying Qualities Tradeoffs. The methodology makes use of control law design metrics from each of the four design objective areas. It combines eigenspace assignment, which allows for direct specification of eigenvalues and eigenvectors, with a graphical approach for representing the metrics that captures numerous design goals in one composite illustration. Sensitivity of the metrics to eigenspace choice is clearly displayed, enabling the designer to assess the cost of design tradeoffs. This approach enhances the designer's ability to make informed design tradeoffs and to reach effective final designs. An example of the CRAFT methodology applied to an advanced experimental fighter and discussion of associated design issues are provided.

Flight experience and the perception of pitch angular displacements in a gondola centrifuge.

PubMed

Tribukait, Arne; Eiken, Ola

2012-05-01

It has been shown that flight experience may induce an adaptation of the vestibular system. The aim of the present work was to elucidate whether pilots, in comparison with non-pilots, have an increased responsiveness to angular displacement canal stimuli in the pitch plane during a conflict between the otolith organs and the semicircular canals. In a large swing-out gondola centrifuge, eight non-pilots, eight fighter pilots, and eight helicopter pilots underwent three runs (2 G, 5 min) heading forward, centripetally, and centrifugally. The direction of the gravitoinertial force was constant with respect to the subject. The visually perceived eye level (VPEL) was measured in darkness by means of an adjustable luminous dot. In the forward position the three groups produced similar results. After acceleration there was a sensation of backward tilt and an increasing depression of VPEL. This effect was smaller in the centripetal position and larger in the centrifugal position. The difference in VPEL between the opposite positions constitutes a measure of the ability to sense the pitch angular displacement canal stimulus related to the swing out of the gondola (60 degrees). This difference was most pronounced initially at the 2-G plateau (mean +/- SD): 13.5 +/- 12.9 degrees (non-pilots), 41.6 +/- 21.1 degrees (fighter pilots), and 19.5 +/- 14.0 degrees (helicopter pilots). There was no significant difference between non-pilots and helicopter pilots. Fighter pilots differed significantly from both non-pilots and helicopter pilots. Vestibular learning effects of flying may be revealed in a centrifuge. Fighter pilots had an increased ability, as compared to non-pilots and helicopter pilots, to perceive pitch angular displacements.

Emerging technologies for bioweapons defense.

PubMed

Nguyen, Sinh; Rosen, Joseph M; Koop, C Everett

2005-01-01

The Global War on Terrorism (GWOT) has changed the way we think about national security. The tragic events of Sept.11 have shown us that world of the 21(st) century is clearly a dangerous place. Terrorism, more than ever, affects the very lives of each and every citizens of our country. Al Qaida has proven that it is able to use simple rudimentary methods to invoke strategic economic losses to our society with our own domestic resources as its weapons. The dawn of the new century has brought forth a new kind of asymmetric war where guerilla fighters are armed not with rifles but with technology at the touch of a keyboard. Warfare as we know it has changed and just as the military has its "transformation", medicine so too must have its own transformation in order to protect our citizen against the ever changing threat of bioterrorism. Virtual Reality and its applications can play a vital role in developing new countermeasures to minimize the catastrophic effects of a potential bioterror attack.

EC91-436-8

NASA Image and Video Library

1991-08-16

The National Aeronautics and Space Administration's Systems Research Aircraft (SRA), a highly modified F-18 jet fighter, during a research flight. The former Navy aircraft was flown by NASA's Dryden Flight Research Center at Edwards Air Force Base, California, to evaluate a number of experimental aerospace technologies in a multi-year, joint NASA/DOD/industry program. Among the more than 20 experiments flight-tested were several involving fiber optic sensor systems. Experiments developed by McDonnell-Douglas and Lockheed-Martin centered on installation and maintenace techniques for various types of fiber-optic hardware proposed for use in military and commercial aircraft, while a Parker-Hannifin experiment focused in alternative fiber-optic designs for position measurement sensors as well as operational experience in handling optical sensor systems. Other experiments flown on this testbed aircraft included electronically-controlled control surface actuators, flush air data collection systems, "smart" skin antennae and laser-based systems. Incorporation of one or more of these technologies in future aircraft and spacecraft could result in signifigant savings in weight, maintenance and overall cost.

Scandium places aluminium welding on a new plateau

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irving, B.

1997-07-01

An interesting new development in nonferrous metallurgy seems to be taking the world by storm. The topic is scandium, a rare metal that is now being mined in the Ukraine. Known for its toughness, it was formerly a top secret material used in fighter planes, including the MIG 29, during the existence of the Soviet Union. This metal is now being introduced into a variety of aluminum alloys in this country, both in base metal and filler metal forms. The results are increases in strength, fatigue life and weldability. US interest in scandium-containing products is burgeoning, examples include aircraft, componentsmore » for automobiles and trucks, high-speed trains, and boats. The technology is being developed and implemented at two laboratories, one in Baltimore, MD, and the other in Kiev, Ukraine. Both laboratories belong to Ashurst Technology Ltd., Hamilton, Bermuda. The author recently visited the Baltimore laboratory where he learned more about scandium and its current and potential effects on industry. This report documents what he learned.« less

Closed-Loop System Identification Experience for Flight Control Law and Flying Qualities Evaluation of a High Performance Fighter Aircraft

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.

1996-01-01

This paper highlights some of the results and issues associated with estimating models to evaluate control law design methods and design criteria for advanced high performance aircraft. Experimental fighter aircraft such as the NASA-High Alpha Research Vehicle (HARV) have the capability to maneuver at very high angles of attack where nonlinear aerodynamics often predominate. HARV is an experimental F/A-18, configured with thrust vectoring and conformal actuated nose strakes. Identifying closed-loop models for this type of aircraft can be made difficult by nonlinearities and high order characteristics of the system. In this paper, only lateral-directional axes are considered since the lateral-directional control law was specifically designed to produce classical airplane responses normally expected with low-order, rigid-body systems. Evaluation of the control design methodology was made using low-order equivalent systems determined from flight and simulation. This allowed comparison of the closed-loop rigid-body dynamics achieved in flight with that designed in simulation. In flight, the On Board Excitation System was used to apply optimal inputs to lateral stick and pedals at five angles at attack : 5, 20, 30, 45, and 60 degrees. Data analysis and closed-loop model identification were done using frequency domain maximum likelihood. The structure of identified models was a linear state-space model reflecting classical 4th-order airplane dynamics. Input time delays associated with the high-order controller and aircraft system were accounted for in data preprocessing. A comparison of flight estimated models with small perturbation linear design models highlighted nonlinearities in the system and indicated that the closed-loop rigid-body dynamics were sensitive to input amplitudes at 20 and 30 degrees angle of attack.

Closed-Loop System Identification Experience for Flight Control Law and Flying Qualities Evaluation of a High Performance Fighter Aircraft

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.

1999-01-01

This paper highlights some of the results and issues associated with estimating models to evaluate control law design methods and design criteria for advanced high performance aircraft. Experimental fighter aircraft such as the NASA High Alpha Research Vehicle (HARV) have the capability to maneuver at very high angles of attack where nonlinear aerodynamics often predominate. HARV is an experimental F/A-18, configured with thrust vectoring and conformal actuated nose strakes. Identifying closed-loop models for this type of aircraft can be made difficult by nonlinearities and high-order characteristics of the system. In this paper only lateral-directional axes are considered since the lateral-directional control law was specifically designed to produce classical airplane responses normally expected with low-order, rigid-body systems. Evaluation of the control design methodology was made using low-order equivalent systems determined from flight and simulation. This allowed comparison of the closed-loop rigid-body dynamics achieved in flight with that designed in simulation. In flight, the On Board Excitation System was used to apply optimal inputs to lateral stick and pedals at five angles of attack: 5, 20, 30, 45, and 60 degrees. Data analysis and closed-loop model identification were done using frequency domain maximum likelihood. The structure of the identified models was a linear state-space model reflecting classical 4th-order airplane dynamics. Input time delays associated with the high-order controller and aircraft system were accounted for in data preprocessing. A comparison of flight estimated models with small perturbation linear design models highlighted nonlinearities in the system and indicated that the estimated closed-loop rigid-body dynamics were sensitive to input amplitudes at 20 and 30 degrees angle of attack.

Multimission airborne radar for the 1990s

NASA Astrophysics Data System (ADS)

Robinson, Thomas H.

1986-07-01

The continuing trend towards the development and production of aircraft capable of multiple missions indicates that future airborne radars must provide a broad spectrum of air-to-air and air-to-ground modes. This paper investigates the modal and functional requirements of a multimode radar projected for the mid-1990s period. The paper is divided into two sections. In the first, the multimission capabilities of current radars are presented to establish trends and capabilities. In the second, the requirements of the next generation system are established. Current multimode radars lay the basis for future systems. The experience gained on the APG-65 and APG-63/70 radars is presented and conclusions are drawn regarding their impact on future system requirements. Not only are modes and performance reviewed for these radars but also their system architecture. The discussion starts with the APG-65 radar which is the first true multimission radar with programmable signal and data processing. Following this, the evolution of the APG-63 radar, culminating with the most recent upgrading resulting in redesignation of APG-70, is presented. The incorporation of air-to-ground capabilities in the APG-70, resulting from the Dual Role Fighter program, is reviewed. Results from the Advanced Fighter Capabilities Demonstration program are presented showing how high resolution SAR was incorporated into a full weapon delivery solution. The specific radar requirements for the next decade radar system are developed. This development is done in two parts. First, mode requirements are synthesized for air superiority, navigation and strike/interdiction operation. This includes low altitude penetration requirements and a review of radar timeline constraints which arise. Second, the fundamental functional requirements needed to implement the mode requirements are explored. Architectural issues and their impact on reliability and sustainability are also considered.

Wind Tunnel Results of Pneumatic Forebody Vortex Control Using Rectangular Slots a Chined Forebody

NASA Technical Reports Server (NTRS)

Alexander, Michael; Meyn, Larry A.

1994-01-01

A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.

Buffet induced structural/flight-control system interaction of the X-29A aircraft

NASA Technical Reports Server (NTRS)

Voracek, David F.; Clarke, Robert

1991-01-01

High angle-of-attack flight regime research is currently being conducted for modern fighter aircraft at the NASA Ames Research Center's Dryden Flight Research Facility. This flight regime provides enhanced maneuverability to fighter pilots in combat situations. Flight research data are being acquired to compare and validate advanced computational fluid dynamic solutions and wind-tunnel models. High angle-of-attack flight creates unique aerodynamic phenomena including wing rock and buffet on the airframe. These phenomena increase the level of excitation of the structural modes, especially on the vertical and horizontal stabilizers. With high gain digital flight-control systems, this structural response may result in an aeroservoelastic interaction. A structural interaction on the X-29A aircraft was observed during high angle-of-attack flight testing. The roll and yaw rate gyros sensed the aircraft's structural modes at 11, 13, and 16 Hz. The rate gyro output signals were then amplified through the flight-control laws and sent as commands to the flaperons and rudder. The flight data indicated that as the angle of attack increased, the amplitude of the buffet on the vertical stabilizer increased, which resulted in more excitation to the structural modes. The flight-control system sensors and command signals showed this increase in modal power at the structural frequencies up to a 30 degree angle-of-attack. Beyond a 30 degree angle-of-attack, the vertical stabilizer response, the feedback sensor amplitude, and control surface command signal amplitude remained relatively constant. Data are presented that show the increased modal power in the aircraft structural accelerometers, the feedback sensors, and the command signals as a function of angle of attack. This structural interaction is traced from the aerodynamic buffet to the flight-control surfaces.

Advanced Fire Information System - A real time fire information system for Africa

NASA Astrophysics Data System (ADS)

Frost, P. E.; Roy, D. P.

2012-12-01

The Council for Scientific and Industrial Research (CSIR) lead by the Meraka Institute and supported by the South African National Space Agency (SANSA) developed the Advanced Fire Information System (AFIS) to provide near real time fire information to a variety of operational and science fire users including disaster managers, fire fighters, farmers and forest managers located across Southern and Eastern Africa. The AFIS combines satellite data with ground based observations and statistics and distributes the information via mobile phone technology. The system was launched in 2004, and Eskom (South Africa' and Africa's largest power utility) quickly became the biggest user and today more than 300 Eskom line managers and support staff receive cell phone and email fire alert messages whenever a wildfire is within 2km of any of the 28 000km of Eskom electricity transmission lines. The AFIS uses Earth observation satellites from NASA and Europe to detect possible actively burning fires and their fire radiative power (FRP). The polar orbiting MODIS Terra and Aqua satellites provide data at around 10am, 15pm, 22am and 3am daily, while the European Geostationary MSG satellite provides 15 minute updates at lower spatial resolution. The AFIS processing system ingests the raw satellite data and within minutes of the satellite overpass generates fire location and FRP based fire intensity information. The AFIS and new functionality are presented including an incident report and permiting system that can be used to differentiate between prescribed burns and uncontrolled wild fires, and the provision of other information including 5-day fire danger forecasts, vegetation curing information and historical burned area maps. A new AFIS mobile application for IOS and Android devices as well as a fire reporting tool are showcased that enable both the dissemination and alerting of fire information and enable user upload of geo tagged photographs and on the fly creation of fire reports for user defined areas of interest.

Pressure distribution on a vectored-thrust V/STOL fighter in the transition-speed range. [wind tunnel tests to measure pressure distribution on body and wing

NASA Technical Reports Server (NTRS)

Mineck, R. E.; Margason, R. J.

1974-01-01

A wind-tunnel investigation has been conducted in the Langley V/STOL tunnel with a vectored-thrust V/STOL fighter configuration to obtain detailed pressure measurements on the body and on the wing in the transition-speed range. The vectored-thrust jet exhaust induced a region of negative pressure coefficients on the lower surface of the wing and on the bottom of the fuselage. The location of the jet exhaust relative to the wing was a major factor in determining the extent of the region of negative pressure coefficients.

Shock capturing finite difference algorithms for supersonic flow past fighter and missile type configurations

NASA Technical Reports Server (NTRS)

Osher, S.

1984-01-01

The construction of a reliable, shock capturing finite difference method to solve the Euler equations for inviscid, supersonic flow past fighter and missile type configurations is highly desirable. The numerical method must have a firm theoretical foundation and must be robust and efficient. It should be able to treat subsonic pockets in a predominantly supersonic flow. The method must also be easily applicable to the complex topologies of the aerodynamic configuration under consideration. The ongoing approach to this task is described and for steady supersonic flows is presented. This scheme is the basic numerical method. Results of work obtained during previous years are presented.

The minimization of pylon-mounted store effects on air combat capability

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1983-01-01

Some effects of pylon-mounted missiles on aft-tail delta wing supersonic fighter concepts have been investigated. Whereas minimum drag penalties do occur with the addition of missiles, the effects at higher lifts, corresponding to maneuvering flight, are less severe and often favorable. Lower speeds and altitudes enhance the maneuvering capability and one-on-one air combat would probably tend to degenerate to subsonic speeds even though the combatants may be flying supersonic fighters. Higher speed (supersonic) flight might best be reserved for interceptors with long-range missiles where the weapon carriage effects at low angles of attack are of prime importance.

Time-History Data of Maneuvers Performed by a Republic F84G Airplane During Squadron Operational Training

NASA Technical Reports Server (NTRS)

Hamer, Harold A.; Mayo, Alton P.

1953-01-01

Preliminary results of one phase of a control-motion study program involving several jet fighter-type airplanes are presented in time-history form and are summarized as maximum measured quantities plotted against indicated airspeed. The results pertain to approximately 1,000 maneuvers performed by a Republic F-84G jet-fighter airplane during squadron operational training. The data include most tactical maneuvers of which the F-84G airplane is capable. Maneuvers were performed at pressure altitudes of 0 to 30,000 feet with indicated airspeeds ranging from the stalling speed to approximately 515 knots.

Flight Reynolds number effects on a fighter-type, circular-arc-19 deg conic boattail nozzle at subsonic speeds

NASA Technical Reports Server (NTRS)

Chamberlin, R.

1974-01-01

A circular-arc - conic boattail nozzle, typical of those used on a twin engine fighter, was tested on an underwing nacelle mounted on an F-106B aircraft. The boattail had a radius ratio r/r sub c of 0.41 and a terminal boattail angle of approximately 19 deg. The gas generator was a J85-GE-13 turbojet engine. The effects of Reynolds number and angle of attack on boattail pressure drag and boattail pressure profiles were investigated. Increasing Reynolds number resulted in reduced boattail drag at both Mach numbers of 0.6 and 0.9.

Subsonic longitudinal and lateral-directional static aerodynamic characteristics of a general research fighter model employing a strake-wing concept

NASA Technical Reports Server (NTRS)

Fox, C. H., Jr.

1978-01-01

A general research fighter model was tested in the Langley 7 by 10 foot high speed tunnel at a Mach number of 0.3. Strakes with exposed semi-spans of 10 percent, 20 percent, and 30 percent of the wing reference semi-span were tested in combination with wings having leading edge sweep angles of 30, 44, and 60 degrees. The angle of attack range was from -4 degrees to approximately 48 degrees at sideslip angles of 0, -5, and 5 degrees. The data are presented without analysis in order to expedite publication.

Calculation of the Lateral Stability of a Directly Coupled Tandem-Towed Fighter Airplane and Correlation with Experimental Data

NASA Technical Reports Server (NTRS)

Shanks, Robert E.

1958-01-01

A theoretical method is presented for predicting the dynamic lateral stability characteristics of an airplane towed in tandem by a much larger airplane. Values of period and time to damp to one-half amplitude and rolling motions calculated by an analog computer have been correlated with results of two experimental investigations conducted in the Langley free-flight tunnel which were part of a U.S. Air Force program (Project FICON) to develop a satisfactory arrangement by which a bomber could tow a parasite fighter. In general, the theoretical results agree with the experimental results.

Combative Sports Injuries: An Edmonton Retrospective.

PubMed

Karpman, Shelby; Reid, Patrick; Phillips, Leah; Qin, Ziling; Gross, Douglas P

2016-07-01

Mixed martial arts (MMA) is an increasingly popular combative sport involving aggressive techniques that present substantial injury risk. We examined the incidence and types of injuries sustained in MMA fights and compared this with injuries sustained in boxing matches. Consecutive Case Series. We used data from post-fight medical examinations on all bouts in Edmonton, Canada, between 2000 and 2013. The participants were 1181 MMA competitors and 550 boxers. The attending physician conducted a mandatory post-fight examination of all fighters and documented the nature of injuries sustained. Boxers were significantly more likely not to experience injury (49.8% vs 59.4%, P < 0.001), whereas MMA fighters were significantly more likely to experience 1 injury (typically contusion/bruising, P < 0.001). Boxers were more likely to experience loss of consciousness (7.1% vs 4.2%, P = 0.01) and serious eye injury (1.1% vs 0.3%, P = 0.02). The overall injury incidence in MMA competitors appears slightly higher than for boxers, but MMA fighters experience more minor contusion/bruising injuries. Boxers are more likely to experience serious injury such as concussion/head trauma involving loss of consciousness or eye injury such as retinal detachment.

Analysis of Idaho fire service education

NASA Astrophysics Data System (ADS)

Roberts, Walter O.

1999-01-01

Becoming a career fire fighter in the state of Idaho requires specialized knowledge and training. Fire science education at Idaho colleges and universities is available only to people who are affiliated with a fire department. Law enforcement curriculum, on the other hand, is available to any interested persons. A student in law enforcement can attend the Police Officers Standards and Training (POST) academy or participate in classes in one of Idaho's institutions for higher education. There are no fire academies in Idaho. Applicants wanting to become professional fire fighters in Idaho are required to compete with applicants from other states; many of whom have had prior fire education and training. Resident Idaho fire fighter applicants are at a disadvantage when applying for Idaho fire fighting positions. Because of this apparent need, I surveyed the Idaho fire chiefs, using a research instrument I developed in a graduate field research class. I wrote the research instrument to determine the educational needs of the Idaho fire service. The College of Southern Idaho (CSI) and the Idaho Fire Chiefs Association (IFCA) were the recipients of this survey. This report, Analysis of Idaho Fire Service Education, describes that research process from beginning to end.

Predicting Tail Buffet Loads of a Fighter Airplane

NASA Technical Reports Server (NTRS)

Moses, Robert W.; Pototzky, Anthony S.

2006-01-01

Buffet loads on aft aerodynamic surfaces pose a recurring problem on most twin-tailed fighter airplanes: During maneuvers at high angles of attack, vortices emanating from various surfaces on the forward parts of such an airplane (engine inlets, wings, or other fuselage appendages) often burst, immersing the tails in their wakes. Although these vortices increase lift, the frequency contents of the burst vortices become so low as to cause the aft surfaces to vibrate destructively. Now, there exists a new analysis capability for predicting buffet loads during the earliest design phase of a fighter-aircraft program. In effect, buffet pressures are applied to mathematical models in the framework of a finite-element code, complete with aeroelastic properties and working knowledge of the spatiality of the buffet pressures for all flight conditions. The results of analysis performed by use of this capability illustrate those vibratory modes of a tail fin that are most likely to be affected by buffet loads. Hence, the results help in identifying the flight conditions during which to expect problems. Using this capability, an aircraft designer can make adjustments to the airframe and possibly the aerodynamics, leading to a more robust design.

Functional Movement Screening Performance of Brazilian Jiu-Jitsu Athletes From Brazil: Differences Considering Practice Time and Combat Style.

PubMed

Del Vecchio, Fabrício Boscolo; Gondim, Denis Foster; Arruda, Antonio Carlos Pereira

2016-08-01

Boscolo Del Vecchio, F, Foster, D, and Arruda, A. Functional movement screening performance of Brazilian jiu-jitsu athletes from Brazil: differences considering practice time and combat style. J Strength Cond Res 30(8): 2341-2347, 2016-Brazilian jiu-jitsu (BJJ) is a grappling combat sport that athletes, lying (guard fighter) or kneeling (pass fighter) on the mat, attempt to force their opponents to submit. Brazilian jiu-jitsu practices may result in muscular imbalances, which increase the risk of injury. Instead, the Functional Movement Screen (FMS) is an evaluation routine that could be related to injury incidence and seeks to detect muscular imbalance and movement dysfunction. Thus, the aim of the study was to investigate the injury profile and the FMS score and their relationship, with consideration for the BJJ fight style. Sports injuries were recorded in the last 12 months of 33 BJJ athletes, and the statistical analyses were applied to a routine evaluation FMS and a score of 14 points or less was considered low performance in FMS. We used a logistic regression; the effect size (ES) was calculated, and 5% was assumed as the statistical significance level. Pass fighters showed a higher percentage of injuries on the thorax (24.24%) than did guard fighters (6.67%, p = 0.01). Upper limbs were the most injured part of the body (χ = 36.7; p < 0.001), and they were 79% of the injuries that occurred in training sessions (χ = 14.53; p < 0.001). Despite the lack of statistical differences in the FMS performance between guard and pass fighters (t = 1.97; p = 0.05), its magnitude was considered medium (ES = 0.77). There was an association between FMS and presence of injury (χ = 4.95; p = 0.03). Considering the FMS score as a predictor and the presence or absence of injury as the dependent variable, the data met a Wald coefficient of 4.55, p = 0.03 and Exp (B) = 5.71. The study found that almost half of the sample had injuries in the upper limbs and a quarter had injuries in the lower limbs in the last year. A poor FMS score was observed, and lower scores in the FMS were associated with a higher risk of injury in BJJ athletes.

Some lessons from NACA/NASA aerodynamic studies following World War II

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1983-01-01

An historical account is presented of the new departures in aerodynamic research conducted by NACA, and subsequently NASA, as a result of novel aircraft technologies and operational regimes encountered in the course of the Second World War. The invention and initial development of the turbojet engine furnished the basis for a new speed/altitude regime in which numerous aerodynamic design problems arose. These included compressibility effects near the speed of sound, with attendant lift/drag efficiency reductions and longitudinal stability enhancements that were accompanied by a directional stability reduction. Major research initiatives were mounted in the investigation of swept, delta, trapezoidal and variable sweep wing configurations, sometimes conducted through flight testing of the 'X-series' aircraft. Attention is also given to the development of the first generation of supersonic fighter aircraft.

GROTTO visualization for decision support

NASA Astrophysics Data System (ADS)

Lanzagorta, Marco O.; Kuo, Eddy; Uhlmann, Jeffrey K.

1998-08-01

In this paper we describe the GROTTO visualization projects being carried out at the Naval Research Laboratory. GROTTO is a CAVE-like system, that is, a surround-screen, surround- sound, immersive virtual reality device. We have explored the GROTTO visualization in a variety of scientific areas including oceanography, meteorology, chemistry, biochemistry, computational fluid dynamics and space sciences. Research has emphasized the applications of GROTTO visualization for military, land and sea-based command and control. Examples include the visualization of ocean current models for the simulation and stud of mine drifting and, inside our computational steering project, the effects of electro-magnetic radiation on missile defense satellites. We discuss plans to apply this technology to decision support applications involving the deployment of autonomous vehicles into contaminated battlefield environments, fire fighter control and hostage rescue operations.

Consideration of technologies for head-down displays

NASA Astrophysics Data System (ADS)

Bartlett, Christopher T.

1998-09-01

The market for military avionics head down displays for which Active Matrix Liquid Crystal Displays (AMLCD) has been specified is both well established and substantial. Typical major programs such as F-22, V-22 and Joint Strike Fighter (JSF) amount to over 15,000 displays. Nevertheless there is an insecurity about the situation because of the dependency upon Japanese and Korean manufacturers and the vagaries of the commercial market. The U.S. has only 7% of the world's manufacturing capability in AMLCD and is seeking alternative technologies to regain a hold in this lucrative business. The U.S. military manufacturers of AMLCD are capable, but can never achieve the benefits of scale that Commercial Off The Shelf (COTS) equipment can offer. In addition to the commercial and political concerns, there are still performance issues related to AMLCD and there is a view that emissive displays in particular can offer advantages over AMLCD. However, it is beneficial to be able to tailor display sizes and there are doubts about the ability of current flat panel technologies to achieve custom, or indeed large area panels either economically, or reliably. It is in this arena that projection displays may be the optimum solution.

Advanced Aerodynamic Design of Passive Porosity Control Effectors

NASA Technical Reports Server (NTRS)

Hunter, Craig A.; Viken, Sally A.; Wood, Richard M.; Bauer, Steven X. S.

2001-01-01

This paper describes aerodynamic design work aimed at developing a passive porosity control effector system for a generic tailless fighter aircraft. As part of this work, a computational design tool was developed and used to layout passive porosity effector systems for longitudinal and lateral-directional control at a low-speed, high angle of attack condition. Aerodynamic analysis was conducted using the NASA Langley computational fluid dynamics code USM3D, in conjunction with a newly formulated surface boundary condition for passive porosity. Results indicate that passive porosity effectors can provide maneuver control increments that equal and exceed those of conventional aerodynamic effectors for low-speed, high-alpha flight, with control levels that are a linear function of porous area. This work demonstrates the tremendous potential of passive porosity to yield simple control effector systems that have no external moving parts and will preserve an aircraft's fixed outer mold line.

Computational Fluid Dynamics (CFD): Future role and requirements as viewed by an applied aerodynamicist. [computer systems design

NASA Technical Reports Server (NTRS)

Yoshihara, H.

1978-01-01

The problem of designing the wing-fuselage configuration of an advanced transonic commercial airliner and the optimization of a supercruiser fighter are sketched, pointing out the essential fluid mechanical phenomena that play an important role. Such problems suggest that for a numerical method to be useful, it must be able to treat highly three dimensional turbulent separations, flows with jet engine exhausts, and complex vehicle configurations. Weaknesses of the two principal tools of the aerodynamicist, the wind tunnel and the computer, suggest a complementing combined use of these tools, which is illustrated by the case of the transonic wing-fuselage design. The anticipated difficulties in developing an adequate turbulent transport model suggest that such an approach may have to suffice for an extended period. On a longer term, experimentation of turbulent transport in meaningful cases must be intensified to provide a data base for both modeling and theory validation purposes.

Beryllium-aluminum alloys for investment castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nachtrab, W.T.; Levoy, N.

1997-05-01

Beryllium-aluminum alloys containing greater than 60 wt % beryllium are very favorable materials for applications requiring light weight and high stiffness. However, when produced by traditional powder metallurgical methods, these alloys are expensive and have limited applications. To reduce the cost of making beryllium-aluminum components, Nuclear Metals Inc. (NMI) and Lockheed Martin Electronics and Missiles have recently developed a family of patented beryllium-aluminum alloys that can be investment cast. Designated Beralcast, the alloys can achieve substantial weight savings because of their high specific strength and stiffness. In some cases, weight has been reduced by up to 50% over aluminum investmentmore » casting. Beralcast is now being used to make thin wall precision investment castings for several advanced aerospace applications, such as the RAH-66 Comanche helicopter and F-22 jet fighter. This article discusses alloy compositions, properties, casting method, and the effects of cobalt additions on strength.« less