Science.gov

Sample records for advanced pollution control

  1. Gas-phase advanced oxidation for effective, efficient in situ control of pollution.

    PubMed

    Johnson, Matthew S; Nilsson, Elna J K; Svensson, Erik A; Langer, Sarka

    2014-01-01

    In this article, gas-phase advanced oxidation, a new method for pollution control building on the photo-oxidation and particle formation chemistry occurring in the atmosphere, is introduced and characterized. The process uses ozone and UV-C light to produce in situ radicals to oxidize pollution, generating particles that are removed by a filter; ozone is removed using a MnO2 honeycomb catalyst. This combination of in situ processes removes a wide range of pollutants with a comparatively low specific energy input. Two proof-of-concept devices were built to test and optimize the process. The laboratory prototype was built of standard ventilation duct and could treat up to 850 m(3)/h. A portable continuous-flow prototype built in an aluminum flight case was able to treat 46 m(3)/h. Removal efficiencies of >95% were observed for propane, cyclohexane, benzene, isoprene, aerosol particle mass, and ozone for concentrations in the range of 0.4-6 ppm and exposure times up to 0.5 min. The laboratory prototype generated a OH(•) concentration derived from propane reaction of (2.5 ± 0.3) × 10(10) cm(-3) at a specific energy input of 3 kJ/m(3), and the portable device generated (4.6 ± 0.4) × 10(9) cm(-3) at 10 kJ/m(3). Based on these results, in situ gas-phase advanced oxidation is a viable control strategy for most volatile organic compounds, specifically those with a OH(•) reaction rate higher than ca. 5 × 10(-13) cm(3)/s. Gas-phase advanced oxidation is able to remove compounds that react with OH and to control ozone and total particulate mass. Secondary pollution including formaldehyde and ultrafine particles might be generated, depending on the composition of the primary pollution.

  2. AIR POLLUTION CONTROL TECHNOLOGIES

    EPA Science Inventory

    This is a chapter for John Wiley & Son's Mechanical Engineers' Handbook, and covers issues involving air pollution control. Various technologies for controlling sulfur oxides is considered including fuel desulfurization. It also considers control of nitrogen oxides including post...

  3. Automotive Pollution Control.

    ERIC Educational Resources Information Center

    Raudenbush, David B.

    Intended for a 1- or 2-month curriculum in auto mechanics, this student manual on automotive pollution control was developed by a subject matter specialist at an area vocational school and tested in a vocational auto shop. Intended either for use in an integrated curriculum or for use in teaching pollution control as a separate course, these 12…

  4. Applications of pulsed power in advanced oxidation and reduction processes for pollution control

    SciTech Connect

    Rosocha, L.A.; Coogan, J.J.; Secker, D.A.; Smith, J.D.

    1993-08-01

    A growing social awareness of the adverse impact of pollutants on our environment and the promulgation of environmental laws and regulations has recently stimulated the development of technologies for pollution abatement and hazardous waste destruction. Pulsed power shows strong promise for contributing to the development of innovative technologies aimed at these applications. At Los Alamos we are engaged in two projects which apply pulsed power technology to the environment: the use of relativistic electron beams and nonequilibrium plasmas for the destruction of hazardous organic compounds in aqueous-based and gaseous-based medial, respectively. Electron beams and nonequilibrium plasmas have also been applied to the treatment of flue gases such as SO{sub x} and NO{sub x} by other researchers. In this paper, we will describe our electron-beam and plasma experiments carried out on hazardous waste destruction. Additionally, we will describe the scaling of electron-beam and nonequilibrium plasma systems to industrial sizes, including discussions of electron accelerator architecture, comparison of continuous-duty versus repetitively pulsed accelerators, plasma-discharge modulators, and needed pulsed power technology development.

  5. Pollution control system

    SciTech Connect

    Voliva, B.H.; Bernstein, I.B.

    1984-09-25

    A pollution control system is disclosed wherein condensable pollutants are removed from a high-temperature gas stream by counterflow contact in a vertical tower with downwardly flowing, relatively cool absorbent oil. The absorbent is at a sufficiently low temperature so as to rapidly condense a portion of the pollutants in order to form a fog of fine droplets of pollutant entrained by the gas stream, which fog is incapable of being absorbed by the absorbent. The remainder of the condensable pollutants is removed by downwardly flowing absorbent oil, and the gas and entrained fog are directed from the tower to gas/droplet separation means, such as an electrostatic precipitator. The fog is thereby separated from the gas and substantially pollutant-free gas is discharged to the atmosphere.

  6. Innovation for Pollution Control

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Kinetic Controls Inc.'s refuse-fired steam generating facility led to the development of an air pollution equipment control device. The device is currently marketed by two NASA/Langley Research Center employees. It automatically senses and compensates for the changes in smoke composition when refuse is used as a fuel by adjusting the precipitator's voltage and current to permit maximum collection of electrically charged dust particles. The control adapts to any electrostatic precipitator and should have extensive commercial applications.

  7. Chemistry for Pollution Control.

    ERIC Educational Resources Information Center

    Everson, Larry

    This booklet presents some methods of quantitative chemical analysis currently used in the field of fresh water pollution control. Only those tests that may be performed with little or no special reagents or pieces of equipment are listed. The booklet addresses the following determinations: (1) acidity; (2) alkalinity; (3) chloride; (4) hardness;…

  8. Water Pollution Control Industry

    ERIC Educational Resources Information Center

    Environmental Science and Technology, 1974

    1974-01-01

    A special report on the state of the water pollution control industry reveals that due to forthcoming federal requirements, sales and the backlogs should increase; problems may ensue because of shortages of materials and inflation. Included are reports from various individual companies. (MLB)

  9. Air Pollution Control, Part I.

    ERIC Educational Resources Information Center

    Strauss, Werner, Ed.

    Authoritative reviews in seven areas of current importance in air pollution control are supplied in this volume, the first of a two-part set. Titles contained in this book are: "Dispersion of Pollutants Emitted into the Atmosphere,""The Formation and Control of Oxides of Nitrogen in Air Pollution,""The Control of Sulfur Emissions from Combustion…

  10. Enforcing pollution control laws

    SciTech Connect

    Russell, C.S.; Harrington, W.; Vaughan, W.J.

    1986-01-01

    The heightened environmental consciousness of the 1970s prompted passage of a multitude of ambitious and unprecedented laws designed to clean up the environment and protect it for future generations. But beyond the mere passing of laws lay the difficult tasks of implementing, monitoring, and enforcing them. The authors of this book describe the current state of air and water pollution monitoring and enforcement activity a decade later, within the context of relevant legal, technological, and statistical developments. They mediate between the concerns of the theoretical literature-where it is generally assumed that violations are discovered and punished-and the real world-where violations are rarely discovered and almost never punished. Monitoring and enforcement procedures to date have been aimed at achieving initial rather than continuing compliance with regulations. The authors contend that it is time for a new approach focusing on the enduring problems of compliance. Economic models are used to show the extent of the difficulties involved in monitoring and enforcing pollution control laws on a continuous basis.

  11. Effect of Fuel Wobbe Number on Pollutant Emissions from Advanced Technology Residential Water Heaters: Results of Controlled Experiments

    SciTech Connect

    Rapp, Vi H.; Singer, Brett C.

    2014-03-01

    The research summarized in this report is part of a larger effort to evaluate the potential air quality impacts of using liquefied natural gas in California. A difference of potential importance between many liquefied natural gas blends and the natural gas blends that have been distributed in California in recent years is the higher Wobbe number of liquefied natural gas. Wobbe number is a measure of the energy delivery rate for appliances that use orifice- or pressure-based fuel metering. The effect of Wobbe number on pollutant emissions from residential water heaters was evaluated in controlled experiments. Experiments were conducted on eight storage water heaters, including five with “ultra low-NO{sub X}” burners, and four on-demand (tankless) water heaters, all of which featured ultra low-NO{sub X} burners. Pollutant emissions were quantified as air-free concentrations in the appliance flue and fuel-based emission factors in units of nanogram of pollutant emitter per joule of fuel energy consumed. Emissions were measured for carbon monoxide (CO), nitrogen oxides (NO{sub X}), nitrogen oxide (NO), formaldehyde and acetaldehyde as the water heaters were operated through defined operating cycles using fuels with varying Wobbe number. The reference fuel was Northern California line gas with Wobbe number ranging from 1344 to 1365. Test fuels had Wobbe numbers of 1360, 1390 and 1420. The most prominent finding was an increase in NO{sub X} emissions with increasing Wobbe number: all five of the ultra low-NO{sub X} storage water heaters and two of the four ultra low-NO{sub X} on-demand water heaters had statistically discernible (p<0.10) increases in NO{sub X} with fuel Wobbe number. The largest percentage increases occurred for the ultra low-NO{sub X} water heaters. There was a discernible change in CO emissions with Wobbe number for all four of the on-demand devices tested. The on-demand water heater with the highest CO emissions also had the largest CO increase

  12. Controlling Indoor Air Pollution.

    ERIC Educational Resources Information Center

    Nero, Anthony V, Jr.

    1988-01-01

    Discusses the health risks posed by indoor air pollutants, such as airborne combustion products, toxic chemicals, and radioactivity. Questions as to how indoor air might be regulated. Calls for new approaches to environmental protection. (TW)

  13. Controlling Population with Pollution

    ERIC Educational Resources Information Center

    Browne, Joseph

    2010-01-01

    Population models are often discussed in algebra, calculus, and differential equations courses. In this article we will use the human population of the world as our application. After quick looks at two common models we'll investigate more deeply a model which incorporates the negative effect that accumulated pollution may have on population.

  14. The Economics of Pollution; Part Three: Can Pollution Be Controlled? Teaching About: Can Pollution Be Controlled?

    ERIC Educational Resources Information Center

    Wolozin, Harold; Reilly, Patricia R.

    In this third of three articles on the economics of pollution control general statements from several sources present a background which questions our ability to devise the necessary tools to fight pollution, even if adequate expenditures of money are provided. In the struggle to control pollution, the economist, it is believed, can provide…

  15. ADVANCED EMISSIONS CONTROL DEVELOPMENT PROGRAM

    SciTech Connect

    G.A. Farthing

    2001-02-06

    The primary objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPs, or air toxics) from coal-fired boilers. The project goal is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPs), fabric filters (baghouses), and wet flue gas desulfurization (WFGD) systems. Development work initially concentrated on the capture of trace metals, fine particulate, hydrogen chloride, and hydrogen fluoride. Recent work has focused almost exclusively on the control of mercury emissions.

  16. Advanced Emissions Control Development Program

    SciTech Connect

    G. A. Farthing; G. T. Amrhein; G. A. Kudlac; D. A. Yurchison; D. K. McDonald; M. G. Milobowski

    2001-03-31

    The primary objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPs, or air toxics) from coal-fired boilers. This objective is being met by identifying ways to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPs), fabric filters (fabric filters), and wet flue gas desulfurization (wet FGD) systems. Development work initially concentrated on the capture of trace metals, hydrogen chloride, and hydrogen fluoride. Recent work has focused almost exclusively on the control of mercury emissions.

  17. Pollution Control Device

    NASA Technical Reports Server (NTRS)

    1989-01-01

    BHA Group Inc.'s PrecipTech Power Guard SQ-200 automatic voltage controller, combined with a remote computer, is an automatic management system for smoke-cleaning precipitators. It is the second generation of the SQ 100 developed at Langley Research Center, and was commercialized by two NASA employees. An electrostatic precipitator cleans the smoke by removing particulate matter from smokestack gases before gases are expelled into the atmosphere. Smokestack gas is passed through a precipitator chamber and exposed to an electrostatic field; dust particles in the gas become electrically charged, migrate to collection surfaces and are "captured." Developed under a NASA program seeking a way to dispose refuse, the system monitors sparking, automatically adjusts to changes in operating conditions and does not require a skilled operator.

  18. Air Pollution Control, Part II.

    ERIC Educational Resources Information Center

    Strauss, Werner, Ed.

    This book contains five major articles in areas of current importance in air pollution control. They are written by authors who are actively participating in the areas on which they report. It is the aim of each article to completely cover theory, experimentation, and practice in the field discussed. The contents are as follows: Emissions,…

  19. Careers in Water Pollution Control.

    ERIC Educational Resources Information Center

    Water Pollution Control Federation, Washington, DC.

    Described are the activities, responsibilities, and educational and training requirements of the major occupations directly concerned with water pollution control. Also provided is an overview of employment trends, salaries, and projected demand for employees. Included in the appendix is a list of colleges and universities which offer…

  20. Advances in cancer control

    SciTech Connect

    Anderson, P.N. ); Engstrom, P.F. ); Mortenson, L.E. )

    1989-01-01

    This book contains the proceedings of the sixth annual meeting on Advances in Cancer Control. Included are the following articles: Barriers and facilitators to compliance with routine mammographic screening, Preliminary report of an intervention to improve mammography skills of radiologists.

  1. Advances in Process Control.

    ERIC Educational Resources Information Center

    Morrison, David L.; And Others

    1982-01-01

    Advances in electronics and computer science have enabled industries (pulp/paper, iron/steel, petroleum/chemical) to attain better control of their processes with resulting increases in quality, productivity, profitability, and compliance with government regulations. (JN)

  2. Advanced Process Control Experiments.

    ERIC Educational Resources Information Center

    Deshpande, Pradeep B.; And Others

    1980-01-01

    Describes laboratory experiments of a chemistry course on advanced process control. The equipment for the process around which these experiments were developed by the University of Louisville was constructed from data provided by Exxon Oil Company. (HM)

  3. Advanced Aerodynamic Control Effectors

    NASA Technical Reports Server (NTRS)

    Wood, Richard M.; Bauer, Steven X. S.

    1999-01-01

    A 1990 research program that focused on the development of advanced aerodynamic control effectors (AACE) for military aircraft has been reviewed and summarized. Data are presented for advanced planform, flow control, and surface contouring technologies. The data show significant increases in lift, reductions in drag, and increased control power, compared to typical aerodynamic designs. The results presented also highlighted the importance of planform selection in the design of a control effector suite. Planform data showed that dramatic increases in lift (greater than 25%) can be achieved with multiple wings and a sawtooth forebody. Passive porosity and micro drag generator control effector data showed control power levels exceeding that available from typical effectors (moving surfaces). Application of an advanced planform to a tailless concept showed benefits of similar magnitude as those observed in the generic studies.

  4. Combined air and water pollution control system

    NASA Technical Reports Server (NTRS)

    Wolverton, Billy C. (Inventor); Jarrell, Lamont (Inventor)

    1990-01-01

    A bioaquatic air pollution control system for controlling both water and atmospheric pollution is disclosed. The pollution control system includes an exhaust for directing polluted gases out of a furnace and a fluid circulating system which circulates fluid, such as waste water, from a source, past the furnace where the fluid flow entrains the pollutants from the furnace. The combined fluid and pollutants are then directed through a rock/plant/microbial filtering system. A suction pump pumps the treated waste water from the filter system past the exhaust to again entrain more pollutants from the furnace where they are combined with the fluid (waste water) and directed to the filter system.

  5. EPA RESEARCH IN URBAN STORMWATER POLLUTION CONTROL

    EPA Science Inventory

    This state-of-the-art on the Environmental Protection Agency' s research in urban stormwater and combined sewer overflow pollution control describes the major elements of the Urban Runoff Pollution Control Program. roblem definition, users assistance tools, management alternative...

  6. Product Guide/1972 [Air Pollution Control Association].

    ERIC Educational Resources Information Center

    Journal of the Air Pollution Control Association, 1971

    1971-01-01

    Reprinted in this pamphlet is the fifth annual directory of air pollution control products as compiled in the "Journal of the Air Pollution Control Association" for December, 1971. The 16-page guide lists manufacturers of emission control equipment and air pollution instrumentation under product classifications as derived from McGraw-Hill's "Air…

  7. AIR POLLUTION CONTROL TECHNOLOGIES (CHAPTER 65)

    EPA Science Inventory

    The chapter discusses the use of technologies for reducing air pollution emissions from stationary sources, with emphasis on the control of combustion gen-erated air pollution. Major stationary sources include utility power boilers, industrial boilers and heaters, metal smelting ...

  8. Air Pollution and Control Legislation in India

    NASA Astrophysics Data System (ADS)

    P Bhave, Prashant; Kulkarni, Nikhil

    2015-09-01

    Air pollution in urban areas arises from multiple sources, which may vary with location and developmental activities. Anthropogenic activities as rampant industrialization, exploitation and over consumption of natural resources, ever growing population size are major contributors of air pollution. The presented review is an effort to discuss various aspects of air pollution and control legislation in India emphasizing on the history, present scenario, international treaties, gaps and drawbacks. The review also presents legislative controls with judicial response to certain landmark judgments related to air pollution. The down sides related to enforcement mechanism for the effective implementation of environmental laws for air pollution control have been highlighted.

  9. Bioresources for control of environmental pollution.

    PubMed

    Sana, Barindra

    2015-01-01

    Environmental pollution is one of the biggest threats to human beings. For practical reasons it is not possible to stop most of the activities responsible for environmental pollution; rather we need to eliminate the pollutants. In addition to other existing means, biological processes can be utilized to get rid of toxic pollutants. Degradation, removal, or deactivation of pollutants by biological means is known as bioremediation. Nature itself has several weapons to deal with natural wastage and some of them are equally active for eliminating nonnatural pollutants. Several plants, microorganisms, and some lower eukaryotes utilize environmental pollutants as nutrients and some of them are very efficient for decontaminating specific types of pollutants. If exploited properly, these natural resources have enough potential to deal with most elements of environmental pollution. In addition, several artificial microbial consortia and genetically modified organisms with high bioremediation potential were developed by application of advanced scientific tools. On the other hand, natural equilibria of ecosystems are being affected by human intervention. Rapid population growth, urbanization, and industrialization are destroying ecological balances and the natural remediation ability of the Earth is being compromised. Several potential bioremediation tools are also being destroyed by biodiversity destruction of unexplored ecosystems. Pollution management by bioremediation is highly dependent on abundance, exploration, and exploitation of bioresources, and biodiversity is the key to success. Better pollution management needs the combined actions of biodiversity conservation, systematic exploration of natural resources, and their exploitation with sophisticated modern technologies.

  10. Biology and Water Pollution Control.

    ERIC Educational Resources Information Center

    Warren, Charles E.

    Within this text, the reader is attuned to the role biology can and should play in combating the alarming increase in water pollution. Both the urgency of the problem and the biological techniques that are being developed to cope with the water pollution crisis are scrutinized; what is and is not known about the problem is explained; past,…

  11. [Research advances in cadmium pollution of peanut (Arachis hypogaea L.)].

    PubMed

    Wang, Kai-rong; Zhang, Lei

    2008-12-01

    Peanut (Arachis hypogaea L.) is a major oil-bearing crop in the world, and as well, an important resource of plant protein and a main raw material for food processing. With the increasing of its direct human consumption and food processing, the Cd concentration in peanut kernel has aroused great concern in recent years. China is a main country of the production and exportation of peanut, but the Cd enrichment in peanut kernel is the main obstacle for its peanut export trade. In this paper, the research advances in Cd pollution of peanut kernel were reviewed, based on the characteristics and mechanisms of Cd accumulation and distribution in peanut kernel, the intra-specific variation of kernel Cd content, and the measures in controlling kernel Cd content. Two strategies were put forward for controlling Cd pollution of peanut kernel, i.e., to reduce the Cd uptake by main root system of peanut plant, and to control the transference of Cd from root to fruit (kernel). In order to applying the strategies effectively, researches on the mechanisms of Cd accumulation in peanut kernel should be enhanced in three aspects, i.e., root vitality and its relationship with Cd accumulation in kernel, mechanism of fruit Cd absorption and its contribution to kernel Cd content, and mechanism of Cd transference in plants and its effects on kernel Cd content.

  12. E-Alerts: Environmental pollution and control (water pollution and control). E-mail newsletter

    SciTech Connect

    1999-04-01

    Topics of discussion include the following: Pollution by municipal wastes, agricultural wastes, industrial wastes, mine wastes, radioactive contaminants; Chemistry and analysis of pollutants; Thermal pollution; Oil pollution; Control techniques and equipment; Sewage treatment; Industrial waste water pretreatment; Hydrology and limnology; Biological and ecological effects; Waste water reuse; Laws, legislation, and regulations; Public administration; Economics; Land use.

  13. Air Pollution and Its Control, Second Edition.

    ERIC Educational Resources Information Center

    Sproull, Wayne T.

    A concise appraisal of our contemporary status and future prospects with regard to air pollution and its control are offered in this text for concerned laymen. What air pollution is, how it endangers health, the cost of controlling it, what is being done about it now, and what should be done are some of the basic questions considered. Topics cover…

  14. Career Guide for Air Pollution Control

    ERIC Educational Resources Information Center

    Baldwin, Lionel V.

    1975-01-01

    This guide to career opportunities in air pollution control includes resource information in this area and provides a listing of colleges and universities offering environmental science programs. The guide was prepared by the S-11 Education and Training Committee of the Air Pollution Control Association. (Author/BT)

  15. Advanced Wavefront Control Techniques

    SciTech Connect

    Olivier, S S; Brase, J M; Avicola, K; Thompson, C A; Kartz, M W; Winters, S; Hartley, R; Wihelmsen, J; Dowla, F V; Carrano, C J; Bauman, B J; Pennington, D M; Lande, D; Sawvel, R M; Silva, D A; Cooke, J B; Brown, C G

    2001-02-21

    this project, work was performed in four areas (1) advanced modeling tools for deformable mirrors (2) low-order wavefront correctors with Alvarez lenses, (3) a direct phase measuring heterdyne wavefront sensor, and (4) high-spatial-frequency wavefront control using spatial light modulators.

  16. Advanced Emissions Control Development Program: Mercury Control

    SciTech Connect

    Evans, A.P.; Redinger, K.W.; Holmes, M.J.

    1997-07-01

    McDermott Technology, Inc. (a subsidiary of Babcock & Wilcox) is conducting the Advanced Emissions Control Development Project (AECDP) which is aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPS) from coal-fired electric utility plants. The need for such controls may arise as the US Environmental Protection Agency (EPA) proceeds with implementation of requirements set forth in the Clean Air Act Amendments (CAAA`s) of 1990. Promulgation of air toxics emissions regulations for electric utility plants could dramatically impact utilities burning coal, their industrial and residential customers, and the coal industry. AECDP project work will supply the information needed by utilities to respond to potential HAPs regulations in a timely, cost-effective, enviromnentally-sound manner which supports the continued use of the Nation`s abundant reserves of coal, such as those in the State of Ohio. The development work is being carried out using the 10 MW Clean Environment Development Facility wherein air toxics emissions control strategies can be developed under controlled conditions. The specific objectives of the project are to (1) measure and understand production and partitioning of air toxics species for a variety of coals, (2) optimize the air toxics removal performance of conventional flue gas cleanup systems, (3) develop advanced air toxics emissions control concepts, (4) develop and validate air toxics emissions measurement and monitoring techniques, and (5) establish a comprehensive, self-consistent air toxics data library. This project is supported by the Department of Energy, the Ohio Coal Development Office within the Ohio Department of Development and Babcock & Wilcox. A comprehensive assessment of HAP emissions from coal-fired electric utility boilers sponsored by the Department of Energy and the Electric Power Research Institute concluded that with the exception of selenium and mercury

  17. [Nonpoint source pollution in Northeast China: research advance].

    PubMed

    Yang, Yu-Hong; Yan, Bai-Xing

    2010-03-01

    In order to understand the research trend on nonpoint source (NPS) pollution in Northeast China and to find its problems and shortcomings, the related research findings from 1991 to 2008 were searched, categorized, and statistically analyzed, so that the regional strategies could be employed to bring water pollution under control. Overall, the research on NPS pollution in Northeast China had an increasing trend, and the research contents included investigation and assessment, quantification of pollution load, mechanisms of pollutants translocation, modeling simulation, and prevention and control. The research interests were nitrogen, phosphorus, sediments, pesticides, and heavy metals. Empirical methods rather than mechanism models were more used to estimate the pollution load, and the researches were more on agricultural rather than urban NPS pollution. The control and management of NPS pollution was remained in soil and water conservation, and lacked of optimal collection assessment for soil and water conservation measures and of assessment for optimal management methods. At present, the research was overall at the stage of theoretical exploration, and controversy remained whether the nonpoint source was major source or not. Incoming researches should focus on the measure application, assessment, basic data collection, determination of regional NPS pollutants, quantification of pollution load, and invention of new technologies; and multi-disciplinary corporation should be strengthened to supply scientific bases for regional water environmental control and prevention.

  18. [Nonpoint source pollution in Northeast China: research advance].

    PubMed

    Yang, Yu-Hong; Yan, Bai-Xing

    2010-03-01

    In order to understand the research trend on nonpoint source (NPS) pollution in Northeast China and to find its problems and shortcomings, the related research findings from 1991 to 2008 were searched, categorized, and statistically analyzed, so that the regional strategies could be employed to bring water pollution under control. Overall, the research on NPS pollution in Northeast China had an increasing trend, and the research contents included investigation and assessment, quantification of pollution load, mechanisms of pollutants translocation, modeling simulation, and prevention and control. The research interests were nitrogen, phosphorus, sediments, pesticides, and heavy metals. Empirical methods rather than mechanism models were more used to estimate the pollution load, and the researches were more on agricultural rather than urban NPS pollution. The control and management of NPS pollution was remained in soil and water conservation, and lacked of optimal collection assessment for soil and water conservation measures and of assessment for optimal management methods. At present, the research was overall at the stage of theoretical exploration, and controversy remained whether the nonpoint source was major source or not. Incoming researches should focus on the measure application, assessment, basic data collection, determination of regional NPS pollutants, quantification of pollution load, and invention of new technologies; and multi-disciplinary corporation should be strengthened to supply scientific bases for regional water environmental control and prevention. PMID:20560338

  19. Air pollution monitoring by advanced spectroscopic techniques.

    PubMed

    Hodgeson, J A; McClenny, W A; Hanst, P L

    1973-10-19

    The monitoring requirements related to air pollution are many and varied. The molecules of concern differ greatly in their chemical and physical properties, in the nature of their environment, and in their concentration ranges. Furthermore, the application may have specific requirements such as rapid response time, ultrasensitivity, multipollutant capability, or capability for remote measurements. For these reasons, no single spectroscopic technique appears to offer a panacea for all monitoring needs. Instead we have attempted to demonstrate in the above discussion that, regardless of the difficulty and complexity of the monitoring problems, spectroscopy offers many tools by which such problems may be solved.

  20. Mercury Specie and Multi-Pollutant Control

    SciTech Connect

    Rob James; Virgil Joffrion; John McDermott; Steve Piche

    2010-05-31

    This project was awarded to demonstrate the ability to affect and optimize mercury speciation and multi-pollutant control using non-intrusive advanced sensor and optimization technologies. The intent was to demonstrate plant-wide optimization systems on a large coal fired steam electric power plant in order to minimize emissions, including mercury (Hg), while maximizing efficiency and maintaining saleable byproducts. Advanced solutions utilizing state-of-the-art sensors and neural network-based optimization and control technologies were proposed to maximize the removal of mercury vapor from the boiler flue gas thereby resulting in lower uncontrolled releases of mercury into the atmosphere. Budget Period 1 (Phase I) - Included the installation of sensors, software system design and establishment of the as-found baseline operating metrics for pre-project and post-project data comparison. Budget Period 2 (Phase II) - Software was installed, data communications links from the sensors were verified, and modifications required to integrate the software system to the DCS were performed. Budget Period 3 (Phase III) - Included the validation and demonstration of all control systems and software, and the comparison of the optimized test results with the targets established for the project site. This report represents the final technical report for the project, covering the entire award period and representing the final results compared to project goals. NeuCo shouldered 61% of the total project cost; while DOE shouldered the remaining 39%. The DOE requires repayment of its investment. This repayment will result from commercial sales of the products developed under the project. NRG's Limestone power plant (formerly owned by Texas Genco) contributed the host site, human resources, and engineering support to ensure the project's success.

  1. Controlling Indoor Air Pollution from Moxibustion

    PubMed Central

    Lu, Chung-Yen; Kang, Sy-Yuan; Liu, Shu-Hui; Mai, Cheng-Wei; Tseng, Chao-Heng

    2016-01-01

    Indoor air quality (IAQ) control of hospitals plays a critical role in protecting both hospital staffs and patients, particularly those who are highly susceptible to the adverse effects of indoor noxious hazards. However, moxibustion in outpatient departments (OPDs) of traditional Chinese medicine (TCM) may be a source of indoor air pollution in hospitals. Some studies have investigated indoor air pollution during moxibustion in Chinese medicine clinics (CMCs) and moxibustion rooms, demonstrating elevated air pollutants that pose a threat to the health of medical staff and patients. Our study investigated the indoor air pollutants of indoor carbon dioxide (CO2), carbon monoxide (CO), formaldehyde (HCHO), total volatile organic compounds (TVOCs), airborne particulate matter with a diameter of ≤10 µm (PM10) and ≤2.5 µm (PM2.5) during moxibustion in an acupuncture and moxibustion room of the OPD in a hospital in Taipei. To evaluate the different control strategies for indoor air pollution from moxibution, a comparison of air pollutants during moxibution among the methods of using alternative old moxa wools, local exhaust ventilation and an air cleaner was conducted. In this study, burning alternative old moxa wools for moxibustion obviously reduced all gaseous pollutants except for aerosols comparing burning fresh moxa wools. Using local exhaust ventilation reduced most of the aerosols after burning moxa. We also found that using an air cleaner was inefficient for controlling indoor air pollutants, particularly gaseous pollutants. Therefore, combining replacing alternative old moxa wools and local exhaust ventilation could be a suitable design for controlling indoor air pollution during moxibustion therapy. PMID:27331817

  2. Advanced technology for reducing aircraft engine pollution

    NASA Technical Reports Server (NTRS)

    Jones, R. E.

    1973-01-01

    Combustor research programs are described whose purpose is to demonstrate significantly lower exhaust emission levels. The proposed EPA regulations covering the allowable levels of emissions will require a major technological effort if these levels are to be met by 1979. Pollution reduction technology is being pursued by NASA through a combination of in-house research, contracted progams, and university grants. In-house research with the swirl-can modular combustor and the double-annular combustor has demonstrated significant reduction in the level of NO(x) emissions. The work is continuing in an attempt to further reduce these levels by improvements in module design and in air-fuel scheduling. Research on the reduction of idle emissions has included the conversion of conventional duplex fuel nozzles to air-assisted nozzles and exploration of the potential improvements possible with fuel staging and variable combustor geometry.

  3. E-Alerts: Environmental pollution and control. E-mail newsletter

    SciTech Connect

    1999-04-01

    Topics of discussion the following: Air Pollution and Control; Noise Pollution and Control; Solid Wastes Pollution and Control; Water Pollution and Control; Pesticides Pollution and Control; Radiation Pollution and Control; Environmental Health and Safety; Environmental Impact Statements.

  4. Health, wealth, and air pollution: advancing theory and methods.

    PubMed Central

    O'Neill, Marie S; Jerrett, Michael; Kawachi, Ichiro; Levy, Jonathan I; Cohen, Aaron J; Gouveia, Nelson; Wilkinson, Paul; Fletcher, Tony; Cifuentes, Luis; Schwartz, Joel

    2003-01-01

    The effects of both ambient air pollution and socioeconomic position (SEP) on health are well documented. A limited number of recent studies suggest that SEP may itself play a role in the epidemiology of disease and death associated with exposure to air pollution. Together with evidence that poor and working-class communities are often more exposed to air pollution, these studies have stimulated discussion among scientists, policy makers, and the public about the differential distribution of the health impacts from air pollution. Science and public policy would benefit from additional research that integrates the theory and practice from both air pollution and social epidemiologies to gain a better understanding of this issue. In this article we aim to promote such research by introducing readers to methodologic and conceptual approaches in the fields of air pollution and social epidemiology; by proposing theories and hypotheses about how air pollution and socioeconomic factors may interact to influence health, drawing on studies conducted worldwide; by discussing methodologic issues in the design and analysis of studies to determine whether health effects of exposure to ambient air pollution are modified by SEP; and by proposing specific steps that will advance knowledge in this field, fill information gaps, and apply research results to improve public health in collaboration with affected communities. PMID:14644658

  5. Control Techniques for Particulate Air Pollutants.

    ERIC Educational Resources Information Center

    National Air Pollution Control Administration (DHEW), Washington, DC.

    Included is a comprehensive review of the approaches commonly recommended for controlling the sources of particulate air pollution. Not all possible combinations of control techniques that might bring about more stringent control of each individual source are reviewed. The many agricultural, commercial, domestic, industrial, and municipal…

  6. Power plant air pollutant control 'Mega' symposium

    SciTech Connect

    2008-07-01

    Topics covered carbon management technologies, mercury (FGD-based controls, sorbents, TOXECON, additives and SO{sub 3} countermeasures 0, NOx (combined controls, SCR), SO{sub 2}, SO{sub 3}, multi-pollutant controls, particulates, and coal combustion products. The poster papers are also included.

  7. System for area pollution control

    SciTech Connect

    Blikken, W.A.; Blikken, W.C.

    1991-12-03

    This paper describes a system for collecting and purifying polluted air in an urban geographic area subject to smog conditions and high volume automotive traffic at spaced intervals in a 24-hour day. It comprises: utilizing a plurality of open water draining which channels in an urban collection area, which channels are arranged in a flow pattern to carry rainfall water to a discharge area, installing covers over the open channels to enclose the open channels to provide an elongate air passage in the channels, providing side passages in the covers to admit drainage water into the channels and to meter polluted air into the channels in response to an induced sub-atmospheric pressure in the channels, providing a high volume of a jet engine of airplane capacity to create sub-atmospheric pressure ins aid channels and carry air in the channels to a converging area of the channels, and providing a depollution apparatus for the air prior to discharge at a site remote from the collection area in which the channels are located.

  8. Air quality and pollution control in Taiwan

    NASA Astrophysics Data System (ADS)

    Fang, Shu-Hwei; Chen, Hsiung-Wen

    Due to limited land and great emphasis on economic growth in the past, Taiwan has an extremely heavy environmental burden. Population density, factory density, as well as densities of motor vehicles are several times higher than those in the United States and Japan. According to the statistics of 1991, the Pollutant Standards Index (PSI) fell mostly in the "moderate" category, i.e., in the range of 50-100. There were 16.25% of the monitored days with PSI above 100, and 0.51% with PSI beyond 200. Suspended particulates were the major pollutant responsible for PSI above 100, followed by carbon monoxide, ozone, and sulfur dioxide. The measures adopted to control air pollution can be divided into four categories, namely law and regulations, control measures on stationary sources, mobile sources and construction projects. The latest amended Air Pollution Control Act was promulgated on 1 February 1992. Several major revisions were introduced to make the amended Act much more stringent than the 1982 amendment, especially on the offenses likely to endanger public health and welfare. In regard to stationary sources, a permit system was enacted to regulate the establishment and alteration of stationary sources. Designated stationary sources are required to be equipped with automatic monitoring facilities. An inspection and enforcement program have expanded to cover more than 10,000 factories. Major control measures for motor vehicles include introducing stringent emission standards for gasoline-fueled vehicles and diesel cars, setting up ratification and approval program for new vehicle model, promoting the inspection/maintenance program on in-used motorcycles and encouraging the use of unleaded and low sulfur fuels. In order to control the pollution caused by construction work, constructors are required to use low-pollution machinery and engineering methods and incorporate pollution prevention into the construction budget.

  9. Topics in Air Pollution Control (SI: 428).

    ERIC Educational Resources Information Center

    Rampacek, Anne; Chaput, Linda

    This course provides information about air pollution control efforts since the passage of the Clean Air Act and places in perspective various issues that have arisen since passage of the act--significant deterioration, maintenance of standards, indirect source review, and transportation controls. Court decisions affecting these issues are cited…

  10. ADVANCED SULFUR CONTROL CONCEPTS

    SciTech Connect

    Apostolos A. Nikolopoulos; Santosh K. Gangwal; William J. McMichael; Jeffrey W. Portzer

    2003-01-01

    Conventional sulfur removal in integrated gasification combined cycle (IGCC) power plants involves numerous steps: COS (carbonyl sulfide) hydrolysis, amine scrubbing/regeneration, Claus process, and tail-gas treatment. Advanced sulfur removal in IGCC systems involves typically the use of zinc oxide-based sorbents. The sulfides sorbent is regenerated using dilute air to produce a dilute SO{sub 2} (sulfur dioxide) tail gas. Under previous contracts the highly effective first generation Direct Sulfur Recovery Process (DSRP) for catalytic reduction of this SO{sub 2} tail gas to elemental sulfur was developed. This process is currently undergoing field-testing. In this project, advanced concepts were evaluated to reduce the number of unit operations in sulfur removal and recovery. Substantial effort was directed towards developing sorbents that could be directly regenerated to elemental sulfur in an Advanced Hot Gas Process (AHGP). Development of this process has been described in detail in Appendices A-F. RTI began the development of the Single-step Sulfur Recovery Process (SSRP) to eliminate the use of sorbents and multiple reactors in sulfur removal and recovery. This process showed promising preliminary results and thus further process development of AHGP was abandoned in favor of SSRP. The SSRP is a direct Claus process that consists of injecting SO{sub 2} directly into the quenched coal gas from a coal gasifier, and reacting the H{sub 2}S-SO{sub 2} mixture over a selective catalyst to both remove and recover sulfur in a single step. The process is conducted at gasifier pressure and 125 to 160 C. The proposed commercial embodiment of the SSRP involves a liquid phase of molten sulfur with dispersed catalyst in a slurry bubble-column reactor (SBCR).

  11. Advances in infection control

    PubMed Central

    Marra, Alexandre Rodrigues

    2016-01-01

    ABSTRACT Several initiatives took place in recent years in relation to nosocomial infection control in order to increase patient safety. Some of these initiatives will be commented in this brief review. PMID:27074240

  12. Advanced sulfur control concepts

    SciTech Connect

    Gangwal, S.K.; Turk, B.S.; Gupta, R.P.

    1995-11-01

    Regenerable metal oxide sorbents, such as zinc titanate, are being developed to efficiently remove hydrogen sulfide (H{sub 2}S) from coal gas in advanced power systems. Dilute air regeneration of the sorbents produces a tailgas containing a few percent sulfur dioxide (SO{sub 2}). Catalytic reduction of the SO{sub 2} to elemental sulfur with a coal gas slipstream using the Direct Sulfur Recovery Process (DSRP) is a leading first-generation technology. Currently the DSRP is undergoing field testing at gasifier sites. The objective of this study is to develop second-generation processes that produce elemental sulfur without coal gas or with limited use. Novel approaches that were evaluated to produce elemental sulfur from sulfided sorbents include (1) sulfur dioxide (SO{sub 2}) regeneration, (2) substoichiometric (partial) oxidation, (3) steam regeneration followed by H{sub 2}S oxidation, and (4) steam-air regeneration. Preliminary assessment of these approaches indicated that developing SO{sub 2} regeneration faced the fewest technical and economic problems among the four process options. Elemental sulfur is the only likely product of SO{sub 2} regeneration and the SO{sub 2} required for the regeneration can be obtained by burning a portion of the sulfur produced. Experimental efforts have thus been concentrated on SO{sub 2}-based regeneration processes. Results from laboratory investigations are presented and discussed.

  13. Variance Design and Air Pollution Control

    ERIC Educational Resources Information Center

    Ferrar, Terry A.; Brownstein, Alan B.

    1975-01-01

    Air pollution control authorities were forced to relax air quality standards during the winter of 1972 by granting variances. This paper examines the institutional characteristics of these variance policies from an economic incentive standpoint, sets up desirable structural criteria for institutional design and arrives at policy guidelines for…

  14. Residuals Management and Water Pollution Control Planning.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC. Office of Public Affairs.

    This pamphlet addresses the problems associated with residuals and water quality especially as it relates to the National Water Pollution Control Program. The types of residuals and appropriate management systems are discussed. Additionally, one section is devoted to the role of citizen participation in developing management programs. (CS)

  15. Public Information for Water Pollution Control.

    ERIC Educational Resources Information Center

    Water Pollution Control Federation, Washington, DC.

    This publication is a handbook for water pollution control personnel to guide them towards a successful public relations program. This handbook was written to incorporate the latest methods of teaching basic public information techniques to the non-professional in this area. Contents include: (1) a rationale for a public information program; (2)…

  16. Water Pollution Control Across the Nation

    ERIC Educational Resources Information Center

    Environmental Science and Technology, 1973

    1973-01-01

    Reviewed are accomplishments, problems, and frustrations faced by individual states in meeting requirements of P.L. 92-500, Federal Water Pollution Control Act Amendments of 1972. State Environmental officials complain the new law may be a hindrance to established cleanup programs. Statistics and charts are given. (BL)

  17. HANDBOOK: CONTROL TECHNIQUES FOR HAZARDOUS AIR POLLUTANTS

    EPA Science Inventory

    This manual is a revision of the first (1986) edition of the Handbook: Control Technologies for Hazardous Air Pollutants, which incorporated information from numerous sources into a single, self-contained reference source focusing on the design and cost of VOC and partic...

  18. E-Alerts: Environmental pollution and control (air pollution and control). E-mail newsletter

    SciTech Connect

    1999-04-01

    Topics of discussion include the following: Air pollution from flue gases, exhaust gases, odors, dust, smog, microorganisms, etc.; Control techniques and equipment; Sampling and analytical techniques, and equipment; Waste gas recovery; Biological and ecological effects; Air pollution chemistry; Acid precipitation; Atmospheric motion; Laws, legislation, and regulations; Public administration; Economics; Land use.

  19. Integrated Watershed Pollution Control at Wujingang Canal, China

    NASA Astrophysics Data System (ADS)

    Zheng, Z.; Yang, X.; Luo, X.

    2012-04-01

    With a drainage area of 400 square kilometers, Wujingang Canal is located at the economically developed Yangtz Delta of eastern China. As a major tributary, the canal contributes a significant amount of pollutant load to the Lake Tai. Over the past many years, water quality of the canal and its tributaries could not meet the lowest Category V of Chinese surface water quality standard, indicating that its water is not suitable for the purposes of irrigation or scenic views. Major pollution sources in the watershed include industries, residential households, agriculture, fishery, and animal feedlot operations. A comprehensive plan with a budget of 2 billion RMB for the Wujingang watershed pollution control was developed in 2008 and has been implemented progressively ever since. Major components of the plan include: (1) advanced treatment of wastewater from industries and municipal sewage plants for further removal of nitrogen and phosphorous; (2) industrial wastewater reuse; (3) contiguous treatment of sewage from rural residential households with cost-effective technologies such as tower ecofilter system; (4) recycling of rural wastes to generate high-value added products using technologies such as multi-phase anaerobic co-digestion; and (5) making full use of the local landscape and configuring physical, chemical, and biological pollutant treatment structures to build the "clean river network" for treatment of mildly polluted agricultural discharge and surface runoff. Through the implementation of the above measures, water quality of the Wujingang Canal and its tributaries is expected to improve to meet Category IV of Chinese surface water quality standard by 2012, and Category III standard by 2020. Keywords watershed pollution control, non-point source pollution, rural sewage, rural waste, Lake Tai

  20. Pollution

    ERIC Educational Resources Information Center

    Terry, Luther L.

    1970-01-01

    Our mechanized environment has produced a variety of man-made pollutants. Prevention of pollution and resulting health hazards is a primary challenge. The Federal Government undertakes a large responsibility in the field of environmental control. (CK)

  1. Delayed coker fractionator advanced control

    SciTech Connect

    Jaisinghani, R.; Minter, B. ); Tica, A.; Puglesi, A.; Ojeda, R. )

    1993-08-01

    In a delayed coking process, as coke drum switches are made, rapid changes occur in both the fractionator feed rate and composition. With conventional control, it is not unusual to see long transient behavior of large swings in both quality and flowrates of coker gas oils. This can extract a heavy economic toll, not only in coker operation, but in the operation of downstream units as the upset is propagated. An advanced process control application (APC) was recently implemented on the coker fractionator at the Yacimentos Petroliferos Fiscales (YPF), Lujan de Cuyo Refinery, in Mendoza, Argentina. This coker fractionator control design was unique as it handled two different operating objectives: control of product qualities via tower temperature profile during normal operation and control of gas oil product flow ratio during drum switch. This combination of control objectives in one multivariable predictive control program was achieved by including special logic to decouple the individual tuning requirements. Also, additional logic was included to unambiguously detect and identify drum switch and drum steam out as discrete events within 30 seconds of their actual occurrence. These discrete events were then used as disturbance variables to minimize fractionator transient behavior. As a performance measure, the overhead temperature was controlled within 2 C to 2.5 C of its target, gas oil flows were stabilized during drum switches and steam generation via pump around was maximized. Overall, implementing advanced control for the delayed coker fractionator resulted in substantial benefits from product quality control, product flow control and minimized energy consumption.

  2. Advanced flight control system study

    NASA Technical Reports Server (NTRS)

    Mcgough, J.; Moses, K.; Klafin, J. F.

    1982-01-01

    The architecture, requirements, and system elements of an ultrareliable, advanced flight control system are described. The basic criteria are functional reliability of 10 to the minus 10 power/hour of flight and only 6 month scheduled maintenance. A distributed system architecture is described, including a multiplexed communication system, reliable bus controller, the use of skewed sensor arrays, and actuator interfaces. Test bed and flight evaluation program are proposed.

  3. Water Pollution Scrubber Activity Simulates Pollution Control Devices.

    ERIC Educational Resources Information Center

    Kennedy, Edward C., III; Waggoner, Todd C.

    2003-01-01

    A laboratory activity caused students to think actively about water pollution. The students realized that it would be easier to keep water clean than to remove pollutants. They created a water scrubbing system allowing them to pour water in one end and have it emerge clean at the other end. (JOW)

  4. A Pollution Control Strategy Game: Costs of Control Policies.

    ERIC Educational Resources Information Center

    Bierma, Thomas J.; Walbert, Mark S.

    1987-01-01

    Describes an interactive classroom game designed to enhance student understanding of air pollution control strategies. Discusses the game's focus on the differences in compliance costs that can occur between the three principal control approaches of emission limits, emission permits, and emission taxes. (TW)

  5. Agricultural water pollution control: An interdisciplinary approach

    NASA Astrophysics Data System (ADS)

    Miller, Watkins W.; Ching, Chauncey T. K.; Yanagida, John F.; Jakus, Paul

    1985-01-01

    Regulation and control of agricultural water pollution is unique and difficult to accomplish. Water quality standards are often proposed without adequate consideration of the overall economic impact on agricultural production. This article illustrates how economists and physical scientists can cooperate to develop appropriate control strategies for agricultural water pollution. Data provided by physical scientists and economists are used in a linear programming model to describe salt discharge as a function of water management, production levels, and an associated effluent charge. Four water management activities were chosen on the basis of different costs of production (including a parametrically varied effluent charge), water requirements, alfalfa yields, and levels of salt discharge. Results indicate that when the effluent charge is low (<0.20/metric ton salt discharged), maximum production with maximum salt discharge is most profitable. As the effluent charge is increased (0.20 0.40/metric ton salt discharged), it becomes progressively less profitable to produce alfalfa at maximum levels of pollutant discharge. When the effluent charge is >0.40/metric ton salt discharged, alfalfa production is no longer economically feasible. An important aspect of this approach is that it permits policy makers to identify explicitly the relationship between the environmental standard and the effect on agricultural production.

  6. 30 CFR 780.15 - Air pollution control plan.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Air pollution control plan. 780.15 Section 780....15 Air pollution control plan. (a) For all surface mining activities with projected production rates... application shall contain an air pollution control plan which includes the following: (1) An air...

  7. 30 CFR 784.26 - Air pollution control plan.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Air pollution control plan. 784.26 Section 784... § 784.26 Air pollution control plan. For all surface operations associated with underground mining activities, the application shall contain an air pollution control plan which includes the following: (a)...

  8. 30 CFR 784.26 - Air pollution control plan.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Air pollution control plan. 784.26 Section 784... § 784.26 Air pollution control plan. For all surface operations associated with underground mining activities, the application shall contain an air pollution control plan which includes the following: (a)...

  9. 30 CFR 784.26 - Air pollution control plan.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Air pollution control plan. 784.26 Section 784... § 784.26 Air pollution control plan. For all surface operations associated with underground mining activities, the application shall contain an air pollution control plan which includes the following: (a)...

  10. 30 CFR 780.15 - Air pollution control plan.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Air pollution control plan. 780.15 Section 780....15 Air pollution control plan. (a) For all surface mining activities with projected production rates... application shall contain an air pollution control plan which includes the following: (1) An air...

  11. 30 CFR 780.15 - Air pollution control plan.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Air pollution control plan. 780.15 Section 780....15 Air pollution control plan. (a) For all surface mining activities with projected production rates... application shall contain an air pollution control plan which includes the following: (1) An air...

  12. 30 CFR 784.26 - Air pollution control plan.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Air pollution control plan. 784.26 Section 784... § 784.26 Air pollution control plan. For all surface operations associated with underground mining activities, the application shall contain an air pollution control plan which includes the following: (a)...

  13. 30 CFR 784.26 - Air pollution control plan.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Air pollution control plan. 784.26 Section 784... § 784.26 Air pollution control plan. For all surface operations associated with underground mining activities, the application shall contain an air pollution control plan which includes the following: (a)...

  14. 30 CFR 780.15 - Air pollution control plan.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Air pollution control plan. 780.15 Section 780....15 Air pollution control plan. (a) For all surface mining activities with projected production rates... application shall contain an air pollution control plan which includes the following: (1) An air...

  15. 30 CFR 780.15 - Air pollution control plan.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Air pollution control plan. 780.15 Section 780....15 Air pollution control plan. (a) For all surface mining activities with projected production rates... application shall contain an air pollution control plan which includes the following: (1) An air...

  16. Advanced Thermal Control Flight Experiment.

    NASA Technical Reports Server (NTRS)

    Kirkpatrick, J. P.; Brennan, P. J.

    1973-01-01

    The advanced Thermal Control Flight Experiment on the Applications Technology Satellite (ATS-F) will evaluate, for the first time in a space environment, the performance of a feedback-controlled variable conductance heat pipe and a heat pipe thermal diode. In addition, the temperature control aspects of a phase-change material (PCM) will be demonstrated. The methanol/stainless steel feedback-controlled heat pipe uses helium control gas that is stored in a wicked reservoir. This reservoir is electrically heated through a solid state controller that senses the temperature of the heat source directly. The ammonia/stainless steel diode heat pipe uses excess liquid to block heat transfer in the reverse direction. The PCM is octadecane. Design tradeoffs, fabrication problems, and performance during qualification and flight acceptance tests are discussed.

  17. [Research advances in eco-toxicological diagnosis of soil pollution].

    PubMed

    Liu, Feng; Teng, Hong-Hui; Ren, Bai-Xiang; Shi, Shu-Yun

    2014-09-01

    Soil eco-toxicology provides a theoretical basis for ecological risk assessment of contaminated soils and soil pollution control. Research on eco-toxicological effects and molecular mechanisms of toxic substances in soil environment is the central content of the soil eco-toxicology. Eco-toxicological diagnosis not only gathers all the information of soil pollution, but also provides the overall toxic effects of soil. Therefore, research on the eco-toxicological diagnosis of soil pollution has important theoretical and practical significance. Based on the research of eco-toxicological diagnosis of soil pollution, this paper introduced some common toxicological methods and indicators, with the advantages and disadvantages of various methods discussed. However, conventional biomarkers can only indicate the class of stress, but fail to explain the molecular mechanism of damage or response happened. Biomarkers and molecular diagnostic techniques, which are used to evaluate toxicity of contaminated soil, can explore deeply detoxification mechanisms of organisms under exogenous stress. In this paper, these biomarkers and techniques were introduced systematically, and the future research trends were prospected.

  18. Methanator fueled engines for pollution control

    NASA Technical Reports Server (NTRS)

    Cagliostro, D. E.; Winkler, E. L.

    1973-01-01

    A methanator fueled Otto-cycle engine is compared with other methods proposed to control pollution due to automobile exhaust emissions. The comparison is made with respect to state of development, emission factors, capital cost, operational and maintenance costs, performance, operational limitations, and impact on the automotive industries. The methanator fueled Otto-cycle engine is projected to meet 1975 emission standards and operate at a lower relative total cost compared to the catalytic muffler system and to have low impact. Additional study is required for system development.

  19. Advanced flight control system study

    NASA Technical Reports Server (NTRS)

    Hartmann, G. L.; Wall, J. E., Jr.; Rang, E. R.; Lee, H. P.; Schulte, R. W.; Ng, W. K.

    1982-01-01

    A fly by wire flight control system architecture designed for high reliability includes spare sensor and computer elements to permit safe dispatch with failed elements, thereby reducing unscheduled maintenance. A methodology capable of demonstrating that the architecture does achieve the predicted performance characteristics consists of a hierarchy of activities ranging from analytical calculations of system reliability and formal methods of software verification to iron bird testing followed by flight evaluation. Interfacing this architecture to the Lockheed S-3A aircraft for flight test is discussed. This testbed vehicle can be expanded to support flight experiments in advanced aerodynamics, electromechanical actuators, secondary power systems, flight management, new displays, and air traffic control concepts.

  20. Anxiety, locus of control and appraisal of air pollution

    SciTech Connect

    Navarro, P.L.; Simpson-Housley, P.; de Man, A.F.

    1987-06-01

    100 residents of Santiago de Chile took part in a study of the relationship among locus of control, trait-anxiety, and perception of air pollution. Concern over the problem of atmospheric pollution and number of antipollution measures taken was related to trait-anxiety. Locus of control was associated with variation in awareness of pollution hazard.

  1. Teaching Applied Chemistry in a Pollution Control Context.

    ERIC Educational Resources Information Center

    Sell, Nancy J.

    1982-01-01

    Discusses rationale behind and content of a course (Industrial Pollution Control Techniques) combining knowledge from fields of industrial chemistry and chemical engineering and utilizing this knowledge in the context of understanding pollution problems and potential methods of pollution control. (Author/SK)

  2. Advanced gray rod control assembly

    DOEpatents

    Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

    2013-09-17

    An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

  3. Greenidge Multi-Pollutant Control Project

    SciTech Connect

    Connell, Daniel

    2008-10-18

    The Greenidge Multi-Pollutant Control Project was conducted as part of the U.S. Department of Energy's Power Plant Improvement Initiative to demonstrate an innovative combination of air pollution control technologies that can cost-effectively reduce emissions of SO{sub 2}, NO{sub x}, Hg, acid gases (SO{sub 3}, HCl, and HF), and particulate matter from smaller coal-fired electric generating units (EGUs). There are about 400 units in the United States with capacities of 50-300 MW that currently are not equipped with selective catalytic reduction (SCR), flue gas desulfurization (FGD), or mercury control systems. Many of these units, which collectively represent more than 55 GW of installed capacity, are difficult to retrofit for deep emission reductions because of space constraints and unfavorable economies of scale, making them increasingly vulnerable to retirement or fuel switching in the face of progressively more stringent environmental regulations. The Greenidge Project sought to confirm the commercial readiness of an emissions control system that is specifically designed to meet the environmental compliance requirements of these smaller coal-fired EGUs by offering a combination of deep emission reductions, low capital costs, small space requirements, applicability to high-sulfur coals, mechanical simplicity, and operational flexibility. The multi-pollutant control system includes a NO{sub x}OUT CASCADE{reg_sign} hybrid selective non-catalytic reduction (SNCR)/in-duct SCR system for NO{sub x} control and a Turbosorp{reg_sign} circulating fluidized bed dry scrubbing system (with a new baghouse) for SO{sub 2}, SO{sub 3}, HCl, HF, and particulate matter control. Mercury removal is provided as a co-benefit of the in-duct SCR, dry scrubber, and baghouse, and by injection of activated carbon upstream of the scrubber, if required. The multi-pollutant control system was installed and tested on the 107-MW{sub e}, 1953-vintage AES Greenidge Unit 4 by a team including

  4. Advanced Emissions Control Development Program

    SciTech Connect

    M. J. Holmes

    1998-12-03

    McDermott Technology, Inc. (MTI) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using the Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and hydrogen chloride and hydrogen fluoride.

  5. Advanced Emissions Control Development Program

    SciTech Connect

    A. P. Evans

    1998-12-03

    McDermott Technology, Inc. (MTI) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using the Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species, hydrogen chloride and hydrogen fluoride.

  6. Advanced Emissions Control Development Program

    SciTech Connect

    Evans, A P

    1998-12-03

    Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W's new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

  7. Advanced Emission Control Development Program.

    SciTech Connect

    Evans, A.P.

    1997-12-31

    Babcock & Wilcox (B&W) is conducting a five-year project aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (commonly called air toxics) from coal-fired electric utility plants. The need for air toxic emissions controls may arise as the U. S. Environmental Protection Agency proceeds with implementation of Title III of the Clean Air Act Amendment (CAAA) of 1990. Data generated during the program will provide utilities with the technical and economic information necessary to reliably evaluate various air toxics emissions compliance options such as fuel switching, coal cleaning, and flue gas treatment. The development work is being carried out using B&W`s new Clean Environment Development Facility (CEDF) wherein air toxics emissions control strategies can be developed under controlled conditions, and with proven predictability to commercial systems. Tests conducted in the CEDF provide high quality, repeatable, comparable data over a wide range of coal properties, operating conditions, and emissions control systems. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate, and the inorganic species hydrogen chloride and hydrogen fluoride.

  8. APEX (Air Pollution Exercise) Volume 3: Air Pollution Control Officer's Manual.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Research Triangle Park, NC. Office of Manpower Development.

    The Air Pollution Control Officer's (APCO) Manual is part of a set of 21 manuals (AA 001 009-001 029) used in APEX (Air Pollution Exercise) a computerized college and professional level "real world" game simulation of a community with urban and rural problems, industrial activities, and air pollution difficulties, The first two sections, which are…

  9. APEX (Air Pollution Exercise) Volume 21: Legal References: Air Pollution Control Regulations.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Research Triangle Park, NC. Office of Manpower Development.

    The Legal References: Air Pollution Control Regulations Manual is the last in a set of 21 manuals (AA 001 009-001 029) used in APEX (Air Pollution Exercise), a computerized college and professional level "real world" game simulation of a community with urban and rural problems, industrial activities, and air pollution difficulties. The manual…

  10. Advanced nuclear plant control complex

    DOEpatents

    Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

    1993-01-01

    An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

  11. Historical analysis of SO2 pollution control policies in China.

    PubMed

    Gao, Cailing; Yin, Huaqiang; Ai, Nanshan; Huang, Zhengwen

    2009-03-01

    Coal is not only an important energy source in China but also a major source of air pollution. Because of this, China's national sulfur dioxide (SO(2)) emissions have been the highest in the world for many years, and since the 1990s, the territory of China's south and southwest has become the third largest acid-rain-prone region in the world. In order to control SO(2) emissions, the Chinese government has formulated and promulgated a series of policies and regulations, but it faces great difficulties in putting them into practice. In this retrospective look at the history of SO(2) control in China, we found that Chinese SO(2) control policies have become increasingly strict and rigid. We also found that the environmental policies and regulations are more effective when central officials consistently give environmental protection top priority. Achieving China's environmental goals, however, has been made difficult by China's economic growth. Part of this is due to the practice of environmental protection appearing in the form of an ideological "campaign" or "storm" that lacks effective economic measures. More recently, better enforcement of environmental laws and regulations has been achieved by adding environmental quality to the performance assessment metrics for leaders at all levels. To continue making advances, China needs to reinforce the economic and environmental assessments for pollution control projects and work harder to integrate economic measures into environmental protection. Nonetheless, China has a long way to go before economic growth and environmental protection are balanced.

  12. Advanced Emissions Control Development Program

    SciTech Connect

    A.P.Evans; K.E. Redinger; M.J. Holmes

    1998-04-01

    The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

  13. The Sources of Air Pollution and Their Control.

    ERIC Educational Resources Information Center

    National Air Pollution Control Administration (DHEW), Arlington, VA.

    The problems of air pollution and its control are discussed. Major consideration is given the sources of pollution - motor vehicles, industry, power plants, space heating, and refuse disposal. Annual emission levels of five principle pollutants - carbon monoxide, sulfur dioxide, nitrogen oxides, hydrocarbons, and particulate matter - are listed…

  14. Controlling Nonpoint-Source Water Pollution: A Citizen's Handbook.

    ERIC Educational Resources Information Center

    Hansen, Nancy Richardson; And Others

    Citizens can play an important role in helping their states develop pollution control programs and spurring effective efforts to deal with nonpoint-source pollution. This guide takes the reader step-by-step through the process that states must follow to comply with water quality legislation relevant to nonpoint-source pollution. Part I provides…

  15. Steps Towards Controlling the "Export" of Air Pollution

    ERIC Educational Resources Information Center

    OECD Observer, 1977

    1977-01-01

    Results of a five year study to measure the movement of sulfur pollutants across Europe found these pollutants move hundreds or thousands of kilometers before being deposited in large quantities in countries far from where they originate. The need for cooperation among countries to control sulfur pollutants is stressed. (Author/MA)

  16. Advanced Light Source control system

    SciTech Connect

    Magyary, S.; Chin, M.; Cork, C.; Fahmie, M.; Lancaster, H.; Molinari, P.; Ritchie, A.; Robb, A.; Timossi, C.

    1989-03-01

    The Advanced Light Source (ALS) is a third generation 1--2 GeV synchrotron radiation source designed to provide ports for 60 beamlines. It uses a 50 MeV electron linac and 1.5 GeV, 1 Hz, booster synchrotron for injection into a 1--2 GeV storage ring. Interesting control problems are created because of the need for dynamic closed beam orbit control to eliminate interaction between the ring tuning requirements and to minimize orbit shifts due to ground vibrations. The extremely signal sensitive nature of the experiments requires special attention to the sources of electrical noise. These requirements have led to a control system design which emphasizes connectivity at the accelerator equipment end and a large I/O bandwidth for closed loop system response. Not overlooked are user friendliness, operator response time, modeling, and expert system provisions. Portable consoles are used for local operation of machine equipment. Our solution is a massively parallel system with >120 Mbits/sec I/O bandwidth and >1500 Mips computing power. At the equipment level connections are made using over 600 powerful Intelligent Local Controllers (ILC-s) mounted in 3U size Eurocard slots using fiber-optic cables between rack locations. In the control room, personal computers control and display all machine variables at a 10 Hz rate including the scope signals which are collected though the control system. Commercially available software and industry standards are used extensively. Particular attention is paid to reliability, maintainability and upgradeability. 10 refs., 11 figs.

  17. ADVANCED EMISSIONS CONTROL DEVELOPMENT PROGRAM

    SciTech Connect

    M.J. Holmes

    1999-01-01

    The objective of this project is to develop practical strategies and systems for the simultaneous control of SO{sub 2}, NO{sub x}, particulate matter, and air toxics emissions from coal-fired boilers in such a way as to keep coal economically and environmentally competitive as a utility boiler fuel. Of particular interest is the control of air toxics emissions through the cost-effective use of conventional flue gas clean-up equipment such as electrostatic precipitators (ESP's), fabric filters (baghouses), and SO{sub 2} removal systems such as wet scrubbers and various clean coal technologies. This objective will be achieved through extensive development testing in the state-of-the art, 10 MW{sub e} equivalent, Clean Environment Development Facility (CEDF). The project has extended the capabilities of the CEDF to facilitate air toxics emissions control development work on backend flue gas cleanup equipment. Specifically, an ESP, a baghouse, and a wet scrubber for SO{sub 2} (and air toxics) control were added--all designed to yield air toxics emissions data under controlled conditions, and with proven predictability to commercial systems. A schematic of the CEDF and the project test equipment is shown in Figure 1. The specific objectives of the project are to: (1) Measure and understand production and partitioning of air toxics species in coal-fired power plant systems; (2) Optimize the air toxics removal performance of conventional flue gas cleanup systems; (3) Quantify the impacts of coal cleaning on air toxics emissions; (4) Identify and/or develop advanced air toxics emissions control concepts; (5) Develop and validate air toxics emissions measurement and monitoring techniques; (6) Establish an air toxics data library to facilitate studies of the impacts of coal selection, coal cleaning, and emissions control strategies on the emissions of coal-fired power plants.

  18. ADVANCED EMISSIONS CONTROL DEVELOPMENT PROGRAM

    SciTech Connect

    M.J. Holmes

    1998-10-01

    The objective of this project is to develop practical strategies and systems for the simultaneous control of SO{sub 2}, NO{sub x}, particulate matter, and air toxics emissions from coal-fired boilers in such a way as to keep coal economically and environmentally competitive as a utility boiler fuel. Of particular interest is the control of air toxics emissions through the cost-effective use of conventional flue gas clean-up equipment such as electrostatic precipitators (ESP's), fabric filters (baghouses), and SO{sub 2} removal systems such as wet scrubbers and various clean coal technologies. This objective will be achieved through extensive development testing in the state-of-the art, 10 MW{sub e} equivalent, Clean Environment Development Facility (CEDF). The project has extended the capabilities of the CEDF to facilitate air toxics emissions control development work on backend flue gas cleanup equipment. Specifically, an ESP, a baghouse, and a wet scrubber for SO{sub 2} (and air toxics) control were added--all designed to yield air toxics emissions data under controlled conditions, and with proven predictability to commercial systems. A schematic of the CEDF and the project test equipment is shown in Figure 1. The specific objectives of the project are to: (1) Measure and understand production and partitioning of air toxics species in coal-fired power plant systems; (2) Optimize the air toxics removal performance of conventional flue gas cleanup systems; (3) Quantify the impacts of coal cleaning on air toxics emissions; (4) Identify and/or develop advanced air toxics emissions control concepts; (5) Develop and validate air toxics emissions measurement and monitoring techniques; (6) Establish an air toxics data library to facilitate studies of the impacts of coal selection, coal cleaning, and emissions control strategies on the emissions of coal-fired power plants.

  19. ADVANCED EMISSIONS CONTROL DEVELOPMENT PROGRAM

    SciTech Connect

    M.J. Holmes

    1998-07-01

    The objective of this project is to develop practical strategies and systems for the simultaneous control of SO{sub 2}, NO{sub x}, particulate matter, and air toxics emissions from coal-fired boilers in such a way as to keep coal economically and environmentally competitive as a utility boiler fuel. Of particular interest is the control of air toxics emissions through the cost-effective use of conventional flue gas clean-up equipment such as electrostatic precipitators (ESP's), fabric filters (baghouses), and SO{sub 2} removal systems such as wet scrubbers and various clean coal technologies. This objective will be achieved through extensive development testing in the state-of-the art, 10 MW{sub e} equivalent, Clean Environment Development Facility (CEDF). The project has extended the capabilities of the CEDF to facilitate air toxics emissions control development work on backend flue gas cleanup equipment. Specifically, an ESP, a baghouse, and a wet scrubber for SO{sub 2} (and air toxics) control were added--all designed to yield air toxics emissions data under controlled conditions, and with proven predictability to commercial systems. A schematic of the CEDF and the project test equipment is shown in Figure 1. The specific objectives of the project are to: (1) Measure and understand production and partitioning of air toxics species in coal-fired power plant systems; (2) Optimize the air toxics removal performance of conventional flue gas cleanup systems; (3) Quantify the impacts of coal cleaning on air toxics emissions; (4) Identify and/or develop advanced air toxics emissions control concepts; (5) Develop and validate air toxics emissions measurement and monitoring techniques; (6) Establish an air toxics data library to facilitate studies of the impacts of coal selection, coal cleaning, and emissions control strategies on the emissions of coal-fired power plants.

  20. Economic convergence of environmental control and advanced technology

    SciTech Connect

    Bolli, R.E.; Haslbeck, J.L.

    1995-12-31

    Emerging advanced technologies for environmental control have many advantages over conventional, single pollutant removal processes. Features include high efficiencies, multiple pollutant control and zero waste streams. In the past, the economics for state-of-the-art emission control processes could not compete with proven, low-efficiency scrubbers that create throw away by-products. With the implementation of the Clean Air Act Amendments (CAAA), the entire economic environment has changed. If a single process can provide a facility`s compliance requirements for Title I, Title III and Title IV of the CAAA, its net costs can be lower than conventional technology and actually provide economic incentives for overcontrol. The emission allowance program is maturing and the annual revenues from overcontrol of SO{sub 2} are easily quantified. The economics of NO{sub x} control and offsets are currently being realized as EPA identified Title IV requirements, and facilities begin to realize the impact from Title I NO{sub x} control. Air toxic control from Title III could require yet a third control process for a facility to maintain emission compliance. The costs associated with single control strategies vs. multiple pollutant control processes will be discussed and compared. This paper will also present a specific application of the NOXSO Process and identify the potential advantages that can transform advanced technologies, like NOXSO, into the prudent solution for overall environmental compliance.

  1. 76 FR 39357 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-06

    ... Pollution Control District, Kern County Air Pollution Control District, and Ventura County Air Pollution... proposing to approve revisions to the Imperial County Air Pollution Control District (ICAPCD), Kern County Air Pollution Control District (KCAPCD), and Ventura County Air Pollution Control District...

  2. Advanced catalytic combustors for low pollutant emissions, phase 1

    NASA Technical Reports Server (NTRS)

    Dodds, W. J.

    1979-01-01

    The feasibility of employing the known attractive and distinguishing features of catalytic combustion technology to reduce nitric oxide emissions from gas turbine engines during subsonic, stratospheric cruise operation was investigated. Six conceptual combustor designs employing catalytic combustion were defined and evaluated for their potential to meet specific emissions and performance goals. Based on these evaluations, two parallel-staged, fixed-geometry designs were identified as the most promising concepts. Additional design studies were conducted to produce detailed preliminary designs of these two combustors. Results indicate that cruise nitric oxide emissions can be reduced by an order of magnitude relative to current technology levels by the use of catalytic combustion. Also, these combustors have the potential for operating over the EPA landing-takeoff cycle and at cruise with a low pressure drop, high combustion efficiency and with a very low overall level of emission pollutants. The use of catalytic combustion, however, requires advanced technology generation in order to obtain the time-temperature catalytic reactor performance and durability required for practical aircraft engine combustors.

  3. Controlling Urban Air Pollution: A Benefit-Cost Assessment.

    ERIC Educational Resources Information Center

    Krupnick, Alan J.; Portney, Paul R.

    1991-01-01

    The pros and cons of air pollution control efforts are discussed. Both national and regional air pollution control plans are described. Topics of discussion include benefit-cost analysis, air quality regulation, reducing ozone in the urban areas, the Los Angeles plan, uncertainties, and policy implications. (KR)

  4. 76 FR 39303 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-06

    ... Pollution Control District, Kern County Air Pollution Control District, and Ventura County Air Pollution... taking direct final action to approve revisions to the Imperial County Air Pollution Control District (ICAPCD), Kern County Air Pollution Control District (KCAPCD), and Ventura County Air Pollution...

  5. Agricultural pollution control under Spanish and European environmental policies

    NASA Astrophysics Data System (ADS)

    Martínez, Yolanda; Albiac, José

    2004-10-01

    Nonpoint pollution from agriculture is an important environmental policy issue in Spain and the European Union. Agricultural pollution in Spain is being addressed by the National Irrigation Plan and by the European Water Framework Directive. This article contributes to the ongoing policy decision process by analyzing nonpoint pollution control and presenting results on the efficiency of abatement measures. Results question the reliance of the Water Framework Directive on water pricing as a pollution instrument for reaching good status for all waters because higher water prices close to full recovery cost advocated by the directive appear to be inefficient as an emission control instrument. Another important result is that abatement measures based on input taxes and standards on nitrogen appear to be more suitable than the National Irrigation Plan subsidies designed to promote irrigation investments. The results also contribute with further evidence to the discussion on the appropriate instrument base for pollution control, proving that nonpoint pollution control instruments cannot be assessed accurately without a correct understanding of the key underlying biophysical processes. Nonpoint pollution is characterized by nonlinearities, dynamics, and spatial dependency, and neglect of the dynamic aspects may lead to serious consequences for the design of measures. Finally, a quantitative assessment has been performed to explore discriminating measures based on crop pollution potential on vulnerable soils. No significant welfare gains are found from discriminating control, although results are contingent upon the level of damage, and discrimination could be justified in areas with valuable ecosystems and severe pollution damages.

  6. URBAN RUNOFF POLLUTION CONTROL - STATE-OF-THE-ART

    EPA Science Inventory

    Combined sewer overflows are major sources of water pollution problems, but even discharges of stormwater alone can seriously affect water quality. Current approaches involve control of overflows, treatment, and combinations of the two. Control may involve maximizing treatment wi...

  7. Stormwater Pollutant Control from Critical Source Areas

    EPA Science Inventory

    Critical source areas include: vehicular maintenance facilities, parking lots and bus terminals, junk and lumber yards, industrial storage facilities, loading docks and refueling areas, manufacturing sites, etc. Addressing pollutant runoff from these areas is an important compon...

  8. Historical Analysis of SO2 Pollution Control Policies in China

    NASA Astrophysics Data System (ADS)

    Gao, Cailing; Yin, Huaqiang; Ai, Nanshan; Huang, Zhengwen

    2009-03-01

    Coal is not only an important energy source in China but also a major source of air pollution. Because of this, China’s national sulfur dioxide (SO2) emissions have been the highest in the world for many years, and since the 1990s, the territory of China’s south and southwest has become the third largest acid-rain-prone region in the world. In order to control SO2 emissions, the Chinese government has formulated and promulgated a series of policies and regulations, but it faces great difficulties in putting them into practice. In this retrospective look at the history of SO2 control in China, we found that Chinese SO2 control policies have become increasingly strict and rigid. We also found that the environmental policies and regulations are more effective when central officials consistently give environmental protection top priority. Achieving China’s environmental goals, however, has been made difficult by China’s economic growth. Part of this is due to the practice of environmental protection appearing in the form of an ideological “campaign” or “storm” that lacks effective economic measures. More recently, better enforcement of environmental laws and regulations has been achieved by adding environmental quality to the performance assessment metrics for leaders at all levels. To continue making advances, China needs to reinforce the economic and environmental assessments for pollution control projects and work harder to integrate economic measures into environmental protection. Nonetheless, China has a long way to go before economic growth and environmental protection are balanced.

  9. Controlling Air Pollution; A Primer on Stationary Source Control Techniques.

    ERIC Educational Resources Information Center

    Corman, Rena

    This companion document to "Air Pollution Primer" is written for the nonexpert in air pollution; however, it does assume a familiarity with air pollution problems. This work is oriented toward providing the reader with knowledge about current and proposed air quality legislation and knowledge about available technology to meet these standards for…

  10. Effective Stack Design in Air Pollution Control.

    ERIC Educational Resources Information Center

    Clarke, John H.

    1968-01-01

    Stack design problems fall into two general caterories--(1) those of building re-entry, and (2) those of general area pollution. Extensive research has developed adequate information, available in the literature, to permit effective stack design. A major roadblock to effective design has been the strong belief by architects and engineers that high…

  11. Advanced control technology and its potential for future transport aircraft

    NASA Technical Reports Server (NTRS)

    1976-01-01

    The topics covered include fly by wire, digital control, control configured vehicles, applications to advanced flight vehicles, advanced propulsion control systems, and active control technology for transport aircraft.

  12. Financing under the California Pollution Control Financing Authority

    SciTech Connect

    Seegmiller, K.M.

    1994-12-31

    The California Pollution Control Financing Authority (CPCFA) provides California industry with a method of financing facilities needed to control and eliminate pollution hazards to the environment. The program enables private companies to utilize funds received from the sale of CPCFA bonds for the acquisition, construction, or installation of pollution control facilities and, when possible, to meet environmental requirements imposed by public agencies. Subsequent changes in federal and state law authorized CPCFA to finance municipal and biomass resource recovery projects. Most bonds sold by the CPCFA pay interest to investors that is exempt from both federal and state income taxes. The insurance of these tax-exempt bonds has resulted in significant reductions in pollution control project financing costs for companies which otherwise would have to secure private taxable financing for their projects.

  13. VERIFICATION TESTING OF AIR POLLUTION CONTROL TECHNOLOGY QUALITY MANAGEMENT PLAN

    EPA Science Inventory

    This document is the basis for quality assurance for the Air Pollution Control Technology Verification Center (APCT Center) operated under the U.S. Environmental Protection Agency (EPA). It describes the policies, organizational structure, responsibilities, procedures, and qualit...

  14. A Philosophy of Water Pollution Control--Past and Present.

    ERIC Educational Resources Information Center

    Schroeffer, George J.

    1978-01-01

    An overview of water pollution control in the U.S. is given, leading to an analysis of present policy trends. A "rational environmental program" is called for to provide economic growth and environmental quality. (MDR)

  15. Recruitment and Employment of the Water Pollution Control Specialist.

    ERIC Educational Resources Information Center

    Sherrard, J. H.; Sherrard, F. A.

    1979-01-01

    Presented are the basic principles of personnel recruitment and employment for the water pollution control field. Attention is given to determination of staffing requirements, effective planning, labor sources, affirmative action, and staffing policies. (CS)

  16. 75 FR 56889 - Revisions to the California State Implementation Plan, San Diego County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-17

    ...: EPA is taking direct final action to approve revisions to the San Diego County Air Pollution Control... Environmental protection, Air pollution control, Incorporation by reference, Intergovernmental relations.... * * * * * (c) * * * (379) * * * (i) * * * (B) San Diego County Air Pollution Control District. (1) Rule...

  17. Recent advances in photocatalytic treatment of pollutants in aqueous media.

    PubMed

    Reddy, P Anil Kumar; Reddy, P Venkata Laxma; Kwon, Eilhann; Kim, Ki-Hyun; Akter, Tahmina; Kalagara, Sudhakar

    2016-05-01

    Photocatalysis can be an excellent solution for resolving the world's energy and environmental problems. It has a wide range of applications for the decontamination of diverse hazardous pollutants in aqueous media. Technological progress in this research field has been achieved toward the improvement of the solar sensitivity to enhance the efficiency of pollutant decontamination. As a result, various strategies have been introduced to upgrade photocatalytic performance with the modification of prototypical photocatalyst such as doping, dye sensitization, semiconductor coupling, mesoporous supports, single site, and nano-based catalysts. In this review, a brief survey is presented to describe those strategies based on the evaluation made against various pollutants (such as pharmaceuticals, pesticides, heavy metals, detergents, and dyes) in aqueous media. PMID:26915711

  18. Emerging policies to control nonpoint source pollution of groundwater

    NASA Astrophysics Data System (ADS)

    Harter, T.

    2014-12-01

    Water quality impairment is among the highest ranking public issues of concern in the developed world. While, in Europe and North America, many water quality programs have been put in place over the past half century, regulators difficulties tackling the geographically most widespread water quality degradation in these regions: pollution of groundwater (as opposed to surface water) from diffuse sources (as opposed to point sources), including contamination with nitrate (affecting drinking water supplies in rural areas and at the rural-urban interface) and salinity (affecting irrigation water quality). Other diffuse pollution contaminants include pesticides and emerging contaminants (e.g., antibiotics and pathogens from animal farming). The geographic and hydrologic characteristics of nonpoint source pollution of groundwater are distinctly different from other types of water pollution: individually liable sources are contiguous across the landscape, and internally heterogeneous in space and time. On annually aggregated time scales (most relevant to groundwater), sources are continuously emitting pollution, while pollution levels typically do not exceed MCLs by less than a factor 2. An analysis of key elements of existing water pollution policies to control groundwater pollution from diffuse sources demonstrates the lack of both, science and institutional capacity, while existing point-source approaches cannot be applied toward the control of diffuse pollution to groundwater. For the latter, a key to a successful policy is a tiered, three-way monitoring program based on proxy compliance metrics instead of direct measurement of pollutant discharge, research linking actual pollutant discharges to proxy metrics, and long-term regional groundwater monitoring to establish large scale, long-term trends. Several examples of emerging regulations from California and the EU are given to demonstrate these principles.

  19. The Efficacy of Air Pollution Control Efforts: Evidence from AURA

    NASA Technical Reports Server (NTRS)

    Dickerson, Russell R.; Canty, Tim; Duncan, Bryan N.; Hao, He; Krotkov, Nickolay A.; Salawitch, Ross J.; Stehr, Jeffrey W.; Vinnikov, Konstatin

    2014-01-01

    Observations of NO2, SO2, and H2CO from OMI on AURA provide an excellent record of pollutant concentrations for the past decade. Abatement strategies to control criteria pollutants including ozone and fine particulate matter (PM2.5) have met with varying degrees of success. Sulfur controls had a profound impact on local SO2 concentrations and a measurable impact on PM2.5. Although substantial effort has gone into VOC control, ozone in the eastern US has responded dramatically to NOx emissions controls.

  20. Decentralized and efficient control of transboundary pollution in federal systems

    SciTech Connect

    Silva, E.C.D.

    1997-01-01

    Decentralized control of transboundary pollution in federal systems can be efficient when population crowding is socially costly. In this paper, an upstream region abates pollution or makes an interregional income transfer to the downstream region with the sole intent of deterring immigration. Because either instrument, abatement expenditure or interregional income transfer, alone implements an efficient population distribution between the regions, interregional income transfers are unnecessary for efficiency. Without explicit income transfers, each region provides the efficient portion of the aggregate level of pollution abatement in the Nash equilibrium. 12 refs.

  1. Assessing human exposure to airborne pollutants: Advances and opportunities

    SciTech Connect

    Lioy, P.J. )

    1991-08-01

    A committee which was convened by the National Research Council, recently completed an analysis of new methods and technologies for assessing exposure to air pollutants. The committee identified three major ways of determining human exposure to airborne pollutants. Monitoring the air around an individual with a portable personal air sampler is, of course, the most comprehensive and most accurate. It is also the costliest and most time consuming. The second method is more indirect and involves techniques such as measuring the amount of a contaminant with a stationary monitor and extrapolating exposure by means of personal activity records or mathematical models. Exposure to carbon monoxide inside a car, for example, might be roughly calculated from the amount of time spent in the car and the quantity of carbon monoxide in the car under typical operating conditions. The third method involves biological markers as a measure of the integrated dose within the body and of past contact with pollutants. For example, a marker for airborne lead exposure can be elevated lead levels in the blood. However, this must be weighed against contributions from other media. A final and major point made in the report is the need to have accurate and realistic assessments to ensure optimal reduction of human exposure. To accomplish this, exposure assessment research should be supported by government programs. Although not stated, such research should also be supported by other sectors, including the regulated community.

  2. Learning to Control Advanced Life Support Systems

    NASA Technical Reports Server (NTRS)

    Subramanian, Devika

    2004-01-01

    Advanced life support systems have many interacting processes and limited resources. Controlling and optimizing advanced life support systems presents unique challenges. In particular, advanced life support systems are nonlinear coupled dynamical systems and it is difficult for humans to take all interactions into account to design an effective control strategy. In this project. we developed several reinforcement learning controllers that actively explore the space of possible control strategies, guided by rewards from a user specified long term objective function. We evaluated these controllers using a discrete event simulation of an advanced life support system. This simulation, called BioSim, designed by Nasa scientists David Kortenkamp and Scott Bell has multiple, interacting life support modules including crew, food production, air revitalization, water recovery, solid waste incineration and power. They are implemented in a consumer/producer relationship in which certain modules produce resources that are consumed by other modules. Stores hold resources between modules. Control of this simulation is via adjusting flows of resources between modules and into/out of stores. We developed adaptive algorithms that control the flow of resources in BioSim. Our learning algorithms discovered several ingenious strategies for maximizing mission length by controlling the air and water recycling systems as well as crop planting schedules. By exploiting non-linearities in the overall system dynamics, the learned controllers easily out- performed controllers written by human experts. In sum, we accomplished three goals. We (1) developed foundations for learning models of coupled dynamical systems by active exploration of the state space, (2) developed and tested algorithms that learn to efficiently control air and water recycling processes as well as crop scheduling in Biosim, and (3) developed an understanding of the role machine learning in designing control systems for

  3. A review of existing models and methods to estimate employment effects of pollution control policies

    SciTech Connect

    Darwin, R.F.; Nesse, R.J.

    1988-02-01

    The purpose of this paper is to provide information about existing models and methods used to estimate coal mining employment impacts of pollution control policies. The EPA is currently assessing the consequences of various alternative policies to reduce air pollution. One important potential consequence of these policies is that coal mining employment may decline or shift from low-sulfur to high-sulfur coal producing regions. The EPA requires models that can estimate the magnitude and cost of these employment changes at the local level. This paper contains descriptions and evaluations of three models and methods currently used to estimate the size and cost of coal mining employment changes. The first model reviewed is the Coal and Electric Utilities Model (CEUM), a well established, general purpose model that has been used by the EPA and other groups to simulate air pollution control policies. The second model reviewed is the Advanced Utility Simulation Model (AUSM), which was developed for the EPA specifically to analyze the impacts of air pollution control policies. Finally, the methodology used by Arthur D. Little, Inc. to estimate the costs of alternative air pollution control policies for the Consolidated Coal Company is discussed. These descriptions and evaluations are based on information obtained from published reports and from draft documentation of the models provided by the EPA. 12 refs., 1 fig.

  4. An advanced open path atmospheric pollution monitor for large areas

    SciTech Connect

    Taylor, L.; Suhre, D.; Mani, S.

    1996-12-31

    Over 100 million gallons of radioactive and toxic waste materials generated in weapon materials production are stored in 322 tanks buried within large areas at DOE sites. Toxic vapors occur in the tank headspace due to the solvents used and chemical reactions within the tanks. To prevent flammable or explosive concentration of volatile vapors, the headspace are vented, either manually or automatically, to the atmosphere when the headspace pressure exceeds preset values. Furthermore, 67 of the 177 tanks at the DOE Hanford Site are suspected or are known to be leaking into the ground. These underground storage tanks are grouped into tank farms which contain closely spaced tanks in areas as large as 1 km{sup 2}. The objective of this program is to protect DOE personnel and the public by monitoring the air above these tank farms for toxic air pollutants without the monitor entering the tanks farms, which can be radioactive. A secondary objective is to protect personnel by monitoring the air above buried 50 gallon drums containing moderately low radioactive materials but which could also emit toxic air pollutants.

  5. Advanced automation in space shuttle mission control

    NASA Technical Reports Server (NTRS)

    Heindel, Troy A.; Rasmussen, Arthur N.; Mcfarland, Robert Z.

    1991-01-01

    The Real Time Data System (RTDS) Project was undertaken in 1987 to introduce new concepts and technologies for advanced automation into the Mission Control Center environment at NASA's Johnson Space Center. The project's emphasis is on producing advanced near-operational prototype systems that are developed using a rapid, interactive method and are used by flight controllers during actual Shuttle missions. In most cases the prototype applications have been of such quality and utility that they have been converted to production status. A key ingredient has been an integrated team of software engineers and flight controllers working together to quickly evolve the demonstration systems.

  6. JPL Advanced Thermal Control Technology Roadmap - 2012

    NASA Technical Reports Server (NTRS)

    Birur, Gaj; Rodriguez, Jose I.

    2012-01-01

    NASA's new emphasis on human exploration program for missions beyond LEO requires development of innovative and revolutionary technologies. Thermal control requirements of future NASA science instruments and missions are very challenging and require advanced thermal control technologies. Limited resources requires organizations to cooperate and collaborate; government, industry, universities all need to work together for the successful development of these technologies.

  7. 76 FR 30080 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-24

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution Control District and Ventura County Air Pollution Control District AGENCY: Environmental Protection Agency... Pollution Control District (PCAPCD) and Ventura County Air Pollution Control District (VCAPCD) portion...

  8. 75 FR 3996 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-26

    ... Planning, San Joaquin Valley Air Pollution Control District; letter dated and received August 17, 2009... Sadredin, Executive Director/Air Pollution Control Officer of San Joaquin Valley Air Pollution Control...: EPA's Analysis of San Joaquin Valley Unified Air Pollution Control District's Rule 4684,...

  9. 14 CFR 1274.926 - Clean Air-Water Pollution Control Acts.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 5 2013-01-01 2013-01-01 false Clean Air-Water Pollution Control Acts...-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative... 91-604) and section 308 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et...

  10. 14 CFR 1274.926 - Clean Air-Water Pollution Control Acts.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Clean Air-Water Pollution Control Acts...-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative... 91-604) and section 308 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et...

  11. 14 CFR 1274.926 - Clean Air-Water Pollution Control Acts.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 5 2012-01-01 2012-01-01 false Clean Air-Water Pollution Control Acts...-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative... 91-604) and section 308 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et...

  12. 14 CFR § 1274.926 - Clean Air-Water Pollution Control Acts.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 5 2014-01-01 2014-01-01 false Clean Air-Water Pollution Control Acts. Â...-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative... 91-604) and section 308 of the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et...

  13. Health benefit modelling and optimization of vehicular pollution control strategies

    NASA Astrophysics Data System (ADS)

    Sonawane, Nayan V.; Patil, Rashmi S.; Sethi, Virendra

    2012-12-01

    This study asserts that the evaluation of pollution reduction strategies should be approached on the basis of health benefits. The framework presented could be used for decision making on the basis of cost effectiveness when the strategies are applied concurrently. Several vehicular pollution control strategies have been proposed in literature for effective management of urban air pollution. The effectiveness of these strategies has been mostly studied as a one at a time approach on the basis of change in pollution concentration. The adequacy and practicality of such an approach is studied in the present work. Also, the assessment of respective benefits of these strategies has been carried out when they are implemented simultaneously. An integrated model has been developed which can be used as a tool for optimal prioritization of various pollution management strategies. The model estimates health benefits associated with specific control strategies. ISC-AERMOD View has been used to provide the cause-effect relation between control options and change in ambient air quality. BenMAP, developed by U.S. EPA, has been applied for estimation of health and economic benefits associated with various management strategies. Valuation of health benefits has been done for impact indicators of premature mortality, hospital admissions and respiratory syndrome. An optimization model has been developed to maximize overall social benefits with determination of optimized percentage implementations for multiple strategies. The model has been applied for sub-urban region of Mumbai city for vehicular sector. Several control scenarios have been considered like revised emission standards, electric, CNG, LPG and hybrid vehicles. Reduction in concentration and resultant health benefits for the pollutants CO, NOx and particulate matter are estimated for different control scenarios. Finally, an optimization model has been applied to determine optimized percentage implementation of specific

  14. Pollution Control's Man in the Middle

    ERIC Educational Resources Information Center

    Environmental Science and Technology, 1972

    1972-01-01

    Directs attention to the rise of environmental coordinator positions in industry. Administrative personnel and their responsibilities in two large firms are enumerated--A. J. von Frank, Director of Environmental Control for Allied Chemical Corporation and Jerome Wilkenfeld, Director of Environmental Health for Hooker Chemical Company. (BL)

  15. Controlled Exposures to Air Pollutants and Risk of Cardiac Arrhythmia

    PubMed Central

    Watts, Simon J.; Hunter, Amanda J.; Shah, Anoop S.V.; Bosson, Jenny A.; Unosson, Jon; Barath, Stefan; Lundbäck, Magnus; Cassee, Flemming R.; Donaldson, Ken; Sandström, Thomas; Blomberg, Anders; Newby, David E.; Mills, Nicholas L.

    2014-01-01

    Background: Epidemiological studies have reported associations between air pollution exposure and increases in cardiovascular morbidity and mortality. Exposure to air pollutants can influence cardiac autonomic tone and reduce heart rate variability, and may increase the risk of cardiac arrhythmias, particularly in susceptible patient groups. Objectives: We investigated the incidence of cardiac arrhythmias during and after controlled exposure to air pollutants in healthy volunteers and patients with coronary heart disease. Methods: We analyzed data from 13 double-blind randomized crossover studies including 282 participants (140 healthy volunteers and 142 patients with stable coronary heart disease) from whom continuous electrocardiograms were available. The incidence of cardiac arrhythmias was recorded for each exposure and study population. Results: There were no increases in any cardiac arrhythmia during or after exposure to dilute diesel exhaust, wood smoke, ozone, concentrated ambient particles, engineered carbon nanoparticles, or high ambient levels of air pollution in either healthy volunteers or patients with coronary heart disease. Conclusions: Acute controlled exposure to air pollutants did not increase the short-term risk of arrhythmia in participants. Research employing these techniques remains crucial in identifying the important pathophysiological pathways involved in the adverse effects of air pollution, and is vital to inform environmental and public health policy decisions. Citation: Langrish JP, Watts SJ, Hunter AJ, Shah AS, Bosson JA, Unosson J, Barath S, Lundbäck M, Cassee FR, Donaldson K, Sandström T, Blomberg A, Newby DE, Mills NL. 2014. Controlled exposures to air pollutants and risk of cardiac arrhythmia. Environ Health Perspect 122:747–753; http://dx.doi.org/10.1289/ehp.1307337 PMID:24667535

  16. Operational efficiency subpanel advanced mission control

    NASA Technical Reports Server (NTRS)

    Friedland, Peter

    1990-01-01

    Herein, the term mission control will be taken quite broadly to include both ground and space based operations as well as the information infrastructure necessary to support such operations. Three major technology areas related to advanced mission control are examined: (1) Intelligent Assistance for Ground-Based Mission Controllers and Space-Based Crews; (2) Autonomous Onboard Monitoring, Control and Fault Detection Isolation and Reconfiguration; and (3) Dynamic Corporate Memory Acquired, Maintained, and Utilized During the Entire Vehicle Life Cycle. The current state of the art space operations are surveyed both within NASA and externally for each of the three technology areas and major objectives are discussed from a user point of view for technology development. Ongoing NASA and other governmental programs are described. An analysis of major research issues and current holes in the program are provided. Several recommendations are presented for enhancing the technology development and insertion process to create advanced mission control environments.

  17. Advancing towards universal screening for organic pollutants in waters.

    PubMed

    Hernández, Félix; Ibáñez, María; Portolés, Tania; Cervera, María I; Sancho, Juan V; López, Francisco J

    2015-01-23

    Environmental analytical chemists face the challenge of investigating thousands of potential organic pollutants that may be present in the aquatic environment. High resolution mass spectrometry (HRMS) hyphenated to chromatography offers the possibility of detecting a large number of contaminants without pre-selection of analytes due to its accurate-mass full-spectrum acquisition at good sensitivity. Interestingly, large screening can be made even without reference standards, as the valuable information provided by HRMS allows the tentative identification of the compound detected. In this work, hybrid quadrupole time-of-flight (QTOF) MS was combined with both liquid and gas chromatography (using a single instrument) for screening of around 2000 compounds in waters. This was feasible thanks to the use of atmospheric pressure chemical ionization source in GC. The screening was qualitatively validated for around 300 compounds at three levels (0.02, 0.1, 0.5μg/L), and screening detection limits were established. Surface, ground water and effluent wastewater samples were analyzed, detecting and identifying a notable number of pesticides and transformation products, pharmaceuticals, personal care products, and illicit drugs, among others. This is one of the most universal approaches in terms of comprehensive measurement for broad screening of organic contaminants within a large range of polarity and volatility in waters. PMID:25204505

  18. 76 FR 30025 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-24

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution Control District and Ventura County Air Pollution Control District AGENCY: Environmental Protection Agency... the Placer County Air Pollution Control District (PCAPCD) and Ventura County Air Pollution...

  19. METHODOLOGIES FOR QUANTIFYING POLLUTION PREVENTION BENEFITS FROM LANDFILL GAS CONTROL AND UTILIZATION

    EPA Science Inventory

    The report describes developing emission factors for controlled primary pollutants (e.g., nonmethane organic compounds) and secondary air pollutants (e.g., carbon monoxide). The report addresses the following criteria air pollutants and greenhouse gases: carbon dioxide, carbon mo...

  20. A Regulation for the Control of Atmospheric Pollution, Amended Version.

    ERIC Educational Resources Information Center

    Puerto Rico Environmental Quality Board, San Juan.

    Nine articles, related to the preservation of the natural quality of the air, and to prevention, elimination and control of atmospheric pollution in the Commonwealth of Puerto Rico, are contained in this document. These articles were written and enacted by the Environmental Quality Board in accordance with Law No. 9, approved June 18, 1970 -…

  1. FLUSHING FOR SEWER SEDIMENT, CORROSION, AND POLLUTION CONTROL

    EPA Science Inventory

    This paper overviews causes of combined-sewer deterioration and their heavy pollutant discharges caused by rain events together with a discussion of their control methods. In particular, it covers in-sewer and combined-sewer overflow (CSO) storage-tank-flushing systems for removi...

  2. The Role of Monitoring in Controlling Water Pollution

    NASA Technical Reports Server (NTRS)

    Hirsch, Allan

    1971-01-01

    The purpose of this paper is to provide an overview of trends in the national water pollution control effort and to describe the role of monitoring in that effort, particularly in relation to the responsibilities of the Environmental Protection Agency (EPA). I hope the paper will serve as a useful framework for the more specific discussions of monitoring technology to follow.

  3. Retrofit conserves energy at a water pollution control facility

    SciTech Connect

    Haimes, A.S.; Dedyo, J.

    1980-01-01

    A major retrofit of process structures and incorporation of additional mechanical equipment was undertaken to replace the existing chemical phosphorus removal process with a biological phosphorus removal process. The new process will reduce energy use up to 81% and lime use up to 86% at the Amherst, New York water pollution control facility.

  4. ENVIRONMENTAL TECHNOLOGY VERIFICATION FOR AIR POLLUTION CONTROL TECHNOLOGIES

    EPA Science Inventory

    The report describes the activities and progress of the pilot Air Pollution Control Technologies (APCT) portion of the Environmental Technology Verification (ETV) Program during the period from 09/15/97 to 09/15/02. The objective of the ETV Program is to verify the performance of...

  5. URBAN WET-WEATHER FLOW POLLUTION MANAGEMENT AND CONTROL

    EPA Science Inventory

    One of the challenges in protecting urban watersheds lies in effectively controlling the contaminants in both overland runoff and sewerage system overflows during wet-weather events. Abatement of wet-weather flow (WWF) pollution can be implemented at the source by land managemen...

  6. The fate of mercury collected from air pollution control devices

    EPA Science Inventory

    The mercury that enters a coal-fired power plant, originates from the coal that is burned, and leaves through the output streams that include stack emissions and air pollution control (APC) residues (either in solid or liquid form). This article describes recent fmdings on the fa...

  7. FLUSHING FOR SEWER SEDIMENT, CORROSION, AND POLLUTION CONTROL

    EPA Science Inventory

    This presentation overviews causes of sewer deterioration and heavy pollutant discharges caused by rain events together with a discussion of their control methods. In particular, it covers in-sewer- and combined sewer overflow- (CSO-) storage-tank-flushing systems for removal of ...

  8. Cancer and polluted work places: a case-control study.

    PubMed

    Kjuus, H; Lislerud, A; Lyngdal, P T; Omland, H; Stave, O; Langård, S

    1982-02-01

    The possible association between selected cancers and polluted work places has been studied in a hospital-based, case-control study. By dividing all jobs in the participants working career into "polluted" and "clean", a crude measure for the total industrial exposure a worker experiences throughout his life was established. Among 103 age-matched, case-control pairs the overall estimated relative risk (RR) for exposed subjects (greater than or equal to 10 years in a polluted work place) of developing cancer compared to nonexposed (less than 10 years in a polluted work place) was 1.1. The only subgroup where a significant difference was found between the cases and the controls was the lung cancer subgroup (RR = 4.0, p = 0.02, two-tailed). When the 30 lung cancer cases were compared to an alternative control group consisting of 60 subjects matched for age and smoking habits, an estimated RR of 4.5 was found. A moderate, but not significant association between lung cancer and definite asbestos exposure was also found (RR: 2.3). As most workers are exposed to a variety of industrial agents throughout their working careers, further development of methods for characterizing combined exposures are needed, both for retrospective and prospective purposes. PMID:7068240

  9. Pollution Control Companies U.S.A., 1972.

    ERIC Educational Resources Information Center

    1972

    This book is intended to serve as a useful guide and directory to the present industries embracing the field of environmental control, with emphasis on the prevention and abatement of pollution in its broadest aspects. The volume is divided into two sections: the first section is an alphabetical listing of approximately 1,500 companies or company…

  10. Advanced control architecture for autonomous vehicles

    NASA Astrophysics Data System (ADS)

    Maurer, Markus; Dickmanns, Ernst D.

    1997-06-01

    An advanced control architecture for autonomous vehicles is presented. The hierarchical architecture consists of four levels: a vehicle level, a control level, a rule-based level and a knowledge-based level. A special focus is on forms of internal representation, which have to be chosen adequately for each level. The control scheme is applied to VaMP, a Mercedes passenger car which autonomously performs missions on German freeways. VaMP perceives the environment with its sense of vision and conventional sensors. It controls its actuators for locomotion and attention focusing. Modules for perception, cognition and action are discussed.

  11. Advanced technologies for Mission Control Centers

    NASA Technical Reports Server (NTRS)

    Dalton, John T.; Hughes, Peter M.

    1991-01-01

    Advance technologies for Mission Control Centers are presented in the form of the viewgraphs. The following subject areas are covered: technology needs; current technology efforts at GSFC (human-machine interface development, object oriented software development, expert systems, knowledge-based software engineering environments, and high performance VLSI telemetry systems); and test beds.

  12. Recent advances in active noise control

    NASA Astrophysics Data System (ADS)

    Guicking, D.

    Advances in the field of active noise control over the last few years are reviewed. Some commercially available products and their technical applications are described, with particular attention given to broadband duct noise silencers, broadband active headphones, waveform synthesis, and LMS controllers. Recent theoretical and experimental research activities are then reviewed. These activities are concerned with duct noise, structural sound, interior spaces, algorithms, echo cancellation, and miscellaneous applications.

  13. MERCURY CONTROL WITH ADVANCED HYBRID PARTICULATE COLLECTOR

    SciTech Connect

    Ye Zhuang; Stanley J. Miller

    2005-05-01

    This project was awarded under U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Program Solicitation DE-PS26-00NT40769 and specifically addressed Technical Topical Area 4-Testing Novel and Less Mature Control Technologies on Actual Flue Gas at the Pilot Scale. The project team included the Energy & Environmental Research Center (EERC) as the main contractor; W.L. Gore & Associates, Inc., as a technical and financial partner; and the Big Stone Power Plant operated by Otter Tail Power Company, host for the field-testing portion of the research. Since 1995, DOE has supported development of a new concept in particulate control called the advanced hybrid particulate collector (AHPC). The AHPC has been licensed to W.L. Gore & Associates, Inc., and has been marketed as the Advanced Hybrid{trademark} filter by Gore. The Advanced Hybrid{trademark} filter combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The Advanced Hybrid{trademark} filter provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The Advanced Hybrid{trademark} filter also appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas--solid contactor. The objective of the project was to demonstrate 90% total mercury control in the Advanced Hybrid{trademark} filter at a lower cost than current mercury control estimates. The approach included bench-scale batch tests, larger-scale pilot testing with real flue gas on a coal-fired combustion system, and field demonstration at the 2.5-MW (9000-acfm) scale at a utility power plant to prove scale-up and demonstrate longer-term mercury control

  14. Advanced Active Thermal Control Systems Architecture Study

    NASA Technical Reports Server (NTRS)

    Hanford, Anthony J.; Ewert, Michael K.

    1996-01-01

    The Johnson Space Center (JSC) initiated a dynamic study to determine possible improvements available through advanced technologies (not used on previous or current human vehicles), identify promising development initiatives for advanced active thermal control systems (ATCS's), and help prioritize funding and personnel distribution among many research projects by providing a common basis to compare several diverse technologies. Some technologies included were two-phase thermal control systems, light-weight radiators, phase-change thermal storage, rotary fluid coupler, and heat pumps. JSC designed the study to estimate potential benefits from these various proposed and under-development thermal control technologies for five possible human missions early in the next century. The study compared all the technologies to a baseline mission using mass as a basis. Each baseline mission assumed an internal thermal control system; an external thermal control system; and aluminum, flow-through radiators. Solar vapor compression heat pumps and light-weight radiators showed the greatest promise as general advanced thermal technologies which can be applied across a range of missions. This initial study identified several other promising ATCS technologies which offer mass savings and other savings compared to traditional thermal control systems. Because the study format compares various architectures with a commonly defined baseline, it is versatile and expandable, and is expected to be updated as needed.

  15. Greenridge Multi-Pollutant Control Project Preliminary Public Design Report

    SciTech Connect

    Connell, Daniel P

    2009-01-12

    The Greenidge Multi-Pollutant Control Project is being conducted as part of the U.S. Department of Energy's Power Plant Improvement Initiative to demonstrate an innovative combination of air pollution control technologies that can cost-effectively reduce emissions of SO{sub 2}, NO{sub x}, Hg, acid gases (SO{sub 3}, HCl, and HF), and particulate matter from smaller coal-fired electrical generating units (EGUs). The multi-pollutant control system includes a hybrid selective non-catalytic reduction (SNCR)/in-duct selective catalytic reduction (SCR) system to reduce NOx emissions by {ge}60%, followed by a Turbosorp{reg_sign} circulating fluidized bed dry scrubber system to reduce emissions of SO{sub 2}, SO{sub 3}, HCl, and HF by {ge}95%. Mercury removal of {ge}90% is also targeted via the co-benefits afforded by the in-duct SCR, dry scrubber, and baghouse and by injection of activated carbon upstream of the scrubber, as required. The technology is particularly well suited, because of its relatively low capital and maintenance costs and small space requirements, to meet the needs of coal-fired units with capacities of 50-300 MWe. There are about 440 such units in the United States that currently are not equipped with SCR, flue gas desulfurization (FGD), or mercury control systems. These smaller units are a valuable part of the nation's energy infrastructure, constituting about 60 GW of installed capacity. However, with the onset of the Clean Air Interstate Rule, Clean Air Mercury Rule, and various state environmental actions requiring deep reductions in emissions of SO{sub 2}, NO{sub x}, and mercury, the continued operation of these units increasingly depends upon the ability to identify viable air pollution control retrofit options for them. The large capital costs and sizable space requirements associated with conventional technologies such as SCR and wet FGD make these technologies unattractive for many smaller units. The Greenidge Project aims to confirm the

  16. Architectures & requirements for advanced weapon controllers.

    SciTech Connect

    McMurtrey, Brian J.; Klarer, Paul Richard; Bryan, Jon R.

    2004-02-01

    This report describes work done in FY2003 under Advanced and Exploratory Studies funding for Advanced Weapons Controllers. The contemporary requirements and envisioned missions for nuclear weapons are changing from the class of missions originally envisioned during development of the current stockpile. Technology available today in electronics, computing, and software provides capabilities not practical or even possible 20 years ago. This exploratory work looks at how Weapon Electrical Systems can be improved to accommodate new missions and new technologies while maintaining or improving existing standards in nuclear safety and reliability.

  17. Pollution by metals: Is there a relationship in glycemic control?

    PubMed

    González-Villalva, Adriana; Colín-Barenque, Laura; Bizarro-Nevares, Patricia; Rojas-Lemus, Marcela; Rodríguez-Lara, Vianey; García-Pelaez, Isabel; Ustarroz-Cano, Martha; López-Valdez, Nelly; Albarrán-Alonso, Juan Carlos; Fortoul, Teresa I

    2016-09-01

    There are evidences of environmental pollution and health effects. Metals are pollutants implicated in systemic toxicity. One of the least studied effects, but which is currently becoming more important, is the effect of metals on glycemic control. Metals have been implicated as causes of chronic inflammation and oxidative stress and are associated to obesity, hyperglycemia and even diabetes. Arsenic, iron, mercury, lead, cadmium and nickel have been studied as a risk factor for hyperglycemia and diabetes. There is another group of metals that causes hypoglycemia such as vanadium, chromium, zinc and magnesium by different mechanisms. Zinc, magnesium and chromium deficiency is associated with increased risk of diabetes. This review summarizes some metals involved in glycemic control and pretends to alert health professionals about considering environmental metals as an important factor that could explain the poor glycemic control in patients. Further studies are needed to understand this poorly assessed problem. PMID:27552445

  18. Introduction to Advanced Engine Control Concepts

    NASA Technical Reports Server (NTRS)

    Sanjay, Garg

    2007-01-01

    With the increased emphasis on aircraft safety, enhanced performance and affordability, and the need to reduce the environmental impact of aircraft, there are many new challenges being faced by the designers of aircraft propulsion systems. The Controls and Dynamics Branch at NASA (National Aeronautics and Space Administration) Glenn Research Center (GRC) in Cleveland, Ohio, is leading and participating in various projects in partnership with other organizations within GRC and across NASA, the U.S. aerospace industry, and academia to develop advanced controls and health management technologies that will help meet these challenges through the concept of Intelligent Propulsion Systems. The key enabling technologies for an Intelligent Propulsion System are the increased efficiencies of components through active control, advanced diagnostics and prognostics integrated with intelligent engine control to enhance operational reliability and component life, and distributed control with smart sensors and actuators in an adaptive fault tolerant architecture. This presentation describes the current activities of the Controls and Dynamics Branch in the areas of active component control and propulsion system intelligent control, and presents some recent analytical and experimental results in these areas.

  19. E-Alerts: Environmental pollution and control (solid waste pollution and control). E-mail newsletter

    SciTech Connect

    1999-04-01

    The paper discusses pollution by solid wastes including garbage, scrap, junked automobiles, spoil, sludge, containers; Disposal methods such as composts or land application, injection wells, incineration, sanitary landfills; Mining wastes; Processing for separation and materials recovery; Solid waste utilization; Recycling; Biological and ecological effects; Superfund (Records of Decision, etc.); SITE technology; Laws, legislation, and regulations; Public administration; Economics; Land use. The discussion includes disposal of concentrated or pure liquids such as brines, oils, chemicals, and hazardous materials.

  20. Human factors challenges for advanced process control

    SciTech Connect

    Stubler, W.F.; O`Hara, J..M.

    1996-08-01

    New human-system interface technologies provide opportunities for improving operator and plant performance. However, if these technologies are not properly implemented, they may introduce new challenges to performance and safety. This paper reports the results from a survey of human factors considerations that arise in the implementation of advanced human-system interface technologies in process control and other complex systems. General trends were identified for several areas based on a review of technical literature and a combination of interviews and site visits with process control organizations. Human factors considerations are discussed for two of these areas, automation and controls.

  1. Oxy-fuel combustion with integrated pollution control

    DOEpatents

    Patrick, Brian R.; Ochs, Thomas Lilburn; Summers, Cathy Ann; Oryshchyn, Danylo B.; Turner, Paul Chandler

    2012-01-03

    An oxygen fueled integrated pollutant removal and combustion system includes a combustion system and an integrated pollutant removal system. The combustion system includes a furnace having at least one burner that is configured to substantially prevent the introduction of air. An oxygen supply supplies oxygen at a predetermine purity greater than 21 percent and a carbon based fuel supply supplies a carbon based fuel. Oxygen and fuel are fed into the furnace in controlled proportion to each other and combustion is controlled to produce a flame temperature in excess of 3000 degrees F. and a flue gas stream containing CO2 and other gases. The flue gas stream is substantially void of non-fuel borne nitrogen containing combustion produced gaseous compounds. The integrated pollutant removal system includes at least one direct contact heat exchanger for bringing the flue gas into intimated contact with a cooling liquid to produce a pollutant-laden liquid stream and a stripped flue gas stream and at least one compressor for receiving and compressing the stripped flue gas stream.

  2. Controlling air toxics through advanced coal preparation

    SciTech Connect

    Straszheim, W.E.; Buttermore, W.H.; Pollard, J.L.

    1995-11-01

    This project involves the assessment of advanced coal preparation methods for removing trace elements from coal to reduce the potential for air toxic emissions upon combustion. Scanning electron microscopy-based automated image analysis (SEM-AIA) and advanced washability analyses are being applied with state-of-the-art analytical procedures to predict the removal of elements of concern by advanced column flotation and to confirm the effectiveness of preparation on the quality of quantity of clean coal produced. Specific objectives are to maintain an acceptable recovery of combustible product, while improving the rejection of mineral-associated trace elements. Current work has focused on determining conditions for controlling column flotation system across its operating range and on selection and analysis of samples for determining trace element cleanability.

  3. Solar-Enhanced Advanced Oxidation Processes for Water Treatment: Simultaneous Removal of Pathogens and Chemical Pollutants.

    PubMed

    Tsydenova, Oyuna; Batoev, Valeriy; Batoeva, Agniya

    2015-08-14

    The review explores the feasibility of simultaneous removal of pathogens and chemical pollutants by solar-enhanced advanced oxidation processes (AOPs). The AOPs are based on in-situ generation of reactive oxygen species (ROS), most notably hydroxyl radicals •OH, that are capable of destroying both pollutant molecules and pathogen cells. The review presents evidence of simultaneous removal of pathogens and chemical pollutants by photocatalytic processes, namely TiO2 photocatalysis and photo-Fenton. Complex water matrices with high loads of pathogens and chemical pollutants negatively affect the efficiency of disinfection and pollutant removal. This is due to competition between chemical substances and pathogens for generated ROS. Other possible negative effects include light screening, competitive photon absorption, adsorption on the catalyst surface (thereby inhibiting its photocatalytic activity), etc. Besides, some matrix components may serve as nutrients for pathogens, thus hindering the disinfection process. Each type of water/wastewater would require a tailor-made approach and the variables that were shown to influence the processes-catalyst/oxidant concentrations, incident radiation flux, and pH-need to be adjusted in order to achieve the required degree of pollutant and pathogen removal. Overall, the solar-enhanced AOPs hold promise as an environmentally-friendly way to substitute or supplement conventional water/wastewater treatment, particularly in areas without access to centralized drinking water or sewage/wastewater treatment facilities.

  4. Solar-Enhanced Advanced Oxidation Processes for Water Treatment: Simultaneous Removal of Pathogens and Chemical Pollutants

    PubMed Central

    Tsydenova, Oyuna; Batoev, Valeriy; Batoeva, Agniya

    2015-01-01

    The review explores the feasibility of simultaneous removal of pathogens and chemical pollutants by solar-enhanced advanced oxidation processes (AOPs). The AOPs are based on in-situ generation of reactive oxygen species (ROS), most notably hydroxyl radicals •OH, that are capable of destroying both pollutant molecules and pathogen cells. The review presents evidence of simultaneous removal of pathogens and chemical pollutants by photocatalytic processes, namely TiO2 photocatalysis and photo-Fenton. Complex water matrices with high loads of pathogens and chemical pollutants negatively affect the efficiency of disinfection and pollutant removal. This is due to competition between chemical substances and pathogens for generated ROS. Other possible negative effects include light screening, competitive photon absorption, adsorption on the catalyst surface (thereby inhibiting its photocatalytic activity), etc. Besides, some matrix components may serve as nutrients for pathogens, thus hindering the disinfection process. Each type of water/wastewater would require a tailor-made approach and the variables that were shown to influence the processes—catalyst/oxidant concentrations, incident radiation flux, and pH—need to be adjusted in order to achieve the required degree of pollutant and pathogen removal. Overall, the solar-enhanced AOPs hold promise as an environmentally-friendly way to substitute or supplement conventional water/wastewater treatment, particularly in areas without access to centralized drinking water or sewage/wastewater treatment facilities. PMID:26287222

  5. On-site controls for urban stormwater pollution

    SciTech Connect

    Prey, J. )

    1994-06-01

    Pollutants generated from urban development are now known to produce substantial problems with regard to water quality. Many projects and proposals have been offered to counter these runoff problems. Recently, the Wisconsin Department of Natural Resources undertook a demonstration project to install and examine onsite controls for a developing commercial area in Eau Claire, Wisconsin. This article reviews this project funded under the Wisconsin Nonpoint Source Priority Watershed Program,'' which is administered by the Department of Natural Resources. The program provides local funding to control both urban and agricultural runoff within a designated watershed. In this case, the Lowes Creek Watershed was chosen to feature these controls.

  6. Advanced information technologies for assessing nonpoint source pollution in the vadose zone: Conference overview

    SciTech Connect

    Corwin, D.L.; Loague, K.; Ellsworth, T.R.

    1999-03-01

    The information age has ushered in an awareness of and concern for global environmental problems such as climatic change, ozone depletion, deforestation, desertification, and nonpoint source (NPS) pollution. Nonpoint source pollution is the single greatest threat to surface and subsurface drinking water resources. Nonpoint source pollutants also pose a threat to sustainable agriculture, which is viewed as the most viable means of meeting the food demands of a world population that is expected to reach 9.4 billion by the middle of the next century. The ability to accurately assess present and future NPS pollution impacts on ecosystems ranging from local to global scales would provide a powerful tool for environmental stewardship and guiding future human activities. Assessing NPS pollutant is a multidisciplinary problem. To address the problem, advanced information technologies and methodologies are needed that draw from all areas of science and are applied in a spatial context. It was from this setting that the 1997 Joint AGU Chapman/SSSA Outreach Conference Application of GIS, Remote Sensing, Geostatistics, and Solute Transport Modeling for Assessing Nonpoint Source Pollutants in the Vadose Zone (19--24 Oct. 1997, Riverside, CA) materialized. The objective of the conference was to examine current multidisciplinary technologies and methodologies for assessing NPS pollutants in the vadose zone, and to explore new conceptual approaches. It was the conference`s goal to provide a forum to stimulate multidisciplinary interaction to enhance the development of techniques for the real-time measurement and modeling of NPS pollution in the vadose zone and subsurface waters.

  7. Pollution

    ERIC Educational Resources Information Center

    Rowbotham, N.

    1973-01-01

    Presents the material given in one class period in a course on Environmental Studies at Chesterfield School, England. The topics covered include air pollution, water pollution, fertilizers, and insecticides. (JR)

  8. Preventive techniques of pollution control, the reliability and safety in core sectors including thermal power plant installations and economic evaluation

    SciTech Connect

    Tewari, J.K.

    1997-12-31

    This paper reports on a study of pollution control techniques, thermal power plant reliability and safety, and economics. Included are some illustrative examples dealing with pollution control. Topics include environmental planning, prevention strategy, pesticide use, food pollution, soil pollution, water pollution, thermal power plant emissions, and pollution control equipment.

  9. The Advanced Noise Control Fan Baseline Measurements

    NASA Technical Reports Server (NTRS)

    McAllister, Joseph; Loew, Raymond A.; Lauer, Joel T.; Stuliff, Daniel L.

    2009-01-01

    The NASA Glenn Research Center s (NASA Glenn) Advanced Noise Control Fan (ANCF) was developed in the early 1990s to provide a convenient test bed to measure and understand fan-generated acoustics, duct propagation, and radiation to the farfield. As part of a complete upgrade, current baseline and acoustic measurements were documented. Extensive in-duct, farfield acoustic, and flow field measurements are reported. This is a follow-on paper to documenting the operating description of the ANCF.

  10. 21. Interior view of citric acid air pollution control room ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    21. Interior view of citric acid air pollution control room (also known as scrubber room) in Components Test Laboratory (T-27), looking southeast. Photograph shows upgraded instrumentation, piping, tanks, and technological modifications installed in 1997-99 to accommodate component testing requirements for the Atlas V missile. - Air Force Plant PJKS, Systems Integration Laboratory, Components Test Laboratory, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

  11. The use of gas separation membranes for pollution control

    SciTech Connect

    Logsdon, B.W.; Stull, D.; Pellegrino, J.

    1993-04-01

    Rocky Flats is considering the use of a fluidized bed oxidation unit (FBU) for the destruction of mixed waste. Public concerns about the health effects of such destruction have been intense. In order to allay such concerns and minimize the possible health impacts of the proposed mixed waste destruction, RFP has been investigating novel methods of air pollution control. Among the most promising of these techniques is the use of gas separation membranes, which is described in this report.

  12. [Heavy metal pollution ecology of macro-fungi: research advances and expectation].

    PubMed

    Zhou, Qi-xing; An, Xin-long; Wei, Shu-he

    2008-08-01

    Macro-fungi are the main component of biosphere and one of the ecological resources, and play very important roles in matter cycling and in maintaining ecological balances. This paper summarized and reviewed the research advances in the eco-toxicological effects of heavy metals on macro-fungi, the bioaccumulation function of macro-fungi on heavy metals, the ecological adaptation mechanisms of macro-fungi to heavy metal pollution, the role of macro-fungi as a bio-indicator of heavy metal pollution, and the potential of macro-fungi in the ecological remediation of contaminated environment. To strengthen the researches on the heavy metal pollution ecology of macro-fungi would be of practical significance in the reasonable utilization of macro-fungi resources and in the ecological remediation of contaminated environment.

  13. [Heavy metal pollution ecology of macro-fungi: research advances and expectation].

    PubMed

    Zhou, Qi-xing; An, Xin-long; Wei, Shu-he

    2008-08-01

    Macro-fungi are the main component of biosphere and one of the ecological resources, and play very important roles in matter cycling and in maintaining ecological balances. This paper summarized and reviewed the research advances in the eco-toxicological effects of heavy metals on macro-fungi, the bioaccumulation function of macro-fungi on heavy metals, the ecological adaptation mechanisms of macro-fungi to heavy metal pollution, the role of macro-fungi as a bio-indicator of heavy metal pollution, and the potential of macro-fungi in the ecological remediation of contaminated environment. To strengthen the researches on the heavy metal pollution ecology of macro-fungi would be of practical significance in the reasonable utilization of macro-fungi resources and in the ecological remediation of contaminated environment. PMID:18975768

  14. Control and pollution prevention options for ammonia emissions

    SciTech Connect

    Phillips, J.

    1995-04-01

    In response to requests for guidance concerning technologies available for the control and prevention of ammonia emissions, the Control Technology Center (CTC) initiated a review of current and potential methods for ammonia emissions control. A review of various industries has identified significant sources of ammonia to be fertilizer production, coke production using the by-product recovery method, fossil fuel combustion, livestock management, and refrigeration using ammonia as a refrigerant. Control methods implemented by these sources include wet scrubbers, condensate strippers, recovery and recycle of exhaust streams, capture systems, and good maintenance practices. The report discusses each industry process identified above, concentrating on the sources of ammonia emissions and the controls and pollution prevention (P2) methods applied. Other industries may have minor ammonia emissions but they are not addressed in this report because neither control technologies nor P2 are applied.

  15. Introduction: Assessing non-point source pollution in the vadose zone with advanced information technologies

    NASA Astrophysics Data System (ADS)

    Corwin, Dennis L.; Loague, Keith; Ellsworth, Timothy R.

    The information age has ushered in a global awareness of complex environmental problems that do not respect political or physical boundaries: climatic change, ozone layer depletion, deforestation, desertification, and non-point source (NPS) pollution. Among these global environmental problems, NPS pollutants represent a perfect example of a complex multidisciplinary problem that exists over multiple scales with tremendous spatial and temporal complexity. To address the NPS problem, specific to the vadose zone, advanced information technologies must be applied in a spatial context. An integrated system of advanced information technologies (i.e., global positioning, geographic information system, geostatistics, remote sensing, solute transport modeling, neural networks, transfer functions, fuzzy logic, hierarchical theory, and uncertainty analysis) provides a framework from which real-time and/or simulated assessments of NPS pollution can be made. The ability to accurately assess present and future NPS-pollution impacts on ecosystems ranging from local to global scales provides a powerful tool for environmental stewardship and guiding future human activities.

  16. Control definition study for advanced vehicles

    NASA Technical Reports Server (NTRS)

    Lapins, M.; Martorella, R. P.; Klein, R. W.; Meyer, R. C.; Sturm, M. J.

    1983-01-01

    The low speed, high angle of attack flight mechanics of an advanced, canard-configured, supersonic tactical aircraft designed with moderate longitudinal relaxed static stability (Static Margin, SM = 16% C sub W at M = 0.4) was investigated. Control laws were developed for the longitudinal axis (""G'' or maneuver and angle of attack command systems) and for the lateral/directional axes. The performance of these control laws was examined in engineering simulation. A canard deflection/rate requirement study was performed as part of the ""G'' command law evaluation at low angles of attack. Simulated coupled maneuvers revealed the need for command limiters in all three aircraft axes to prevent departure from controlled flight. When modified with command/maneuver limiters, the control laws were shown to be adequate to prevent aircraft departure during aggressive air combat maneuvering.

  17. 40 CFR 434.84 - Effluent limitations attainable by application of the best conventional pollutant control...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... application of the best conventional pollutant control technology (BCT). 434.84 Section 434.84 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) COAL... pollutant control technology (BCT)....

  18. 76 FR 31242 - Revisions to the California State Implementation Plan, Santa Barbara County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-31

    ... Environmental protection, Air pollution control, Incorporation by reference, Intergovernmental relations... Identification of plan. * * * * * (c) * * * (359) * * * (i) * * * (E) Santa Barbara County Air Pollution Control... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Santa Barbara County...

  19. Assessment of pollution prevention and control technology for plating operations

    NASA Technical Reports Server (NTRS)

    Chalmer, Paul D.; Sonntag, William A.; Cushnie, George C., Jr.

    1995-01-01

    The National Center for Manufacturing Sciences (NCMS) is sponsoring an on-going project to assess pollution prevention and control technology available to the plating industry and to make this information available to those who can benefit from it. Completed project activities include extensive surveys of the plating industry and vendors of technologies and an indepth literature review. The plating industry survey was performed in cooperation with the National Association of Metal Finishers. The contractor that conducted the surveys and prepared the project products was CAI Engineering. The initial products of the project were made available in April, 1994. These products include an extensive report that presents the results of the surveys and literature review and an electronic database. The project results are useful for all those associated with pollution prevention and control in the plating industry. The results show which treatment, recovery and bath maintenance technologies have been most successful for different plating processes and the costs for purchasing and operating these technologies. The project results also cover trends in chemical substitution, the identification of compliance-problem pollutants, sludge generation rates, off-site sludge recovery and disposal options, and many other pertinent topics.

  20. Development of foamed emulsion bioreactor for air pollution control.

    PubMed

    Kan, Eunsung; Deshusses, Marc A

    2003-10-20

    A new type of bioreactor for air pollution control has been developed. The new process relies on an organic-phase emulsion and actively growing pollutant-degrading microorganisms, made into a foam with the air being treated. This new reactor is referred to as a foamed emulsion bioreactor (FEBR). As there is no packing in the reactor, the FEBR is not subject to clogging. Mathematical modeling of the process and proof of concept using a laboratory prototype revealed that the foamed emulsion bioreactor greatly surpasses the performance of existing gas-phase bioreactors. Experimental results showed a toluene elimination capacity as high as 285 g(toluene) m(-3) (reactor) h(-1) with a removal efficiency of 95% at a gas residence time of 15 s and a toluene inlet concentration of 1-1.3 g x m(-3). Oxygen limited the reactor performance at toluene concentration above about 0.7-1.0 g x m(-3); consequently, performance was significantly improved when pure oxygen was added to the contaminated air. The elimination capacity increased from 204 to 408 g x m(-3) h(-1) with >77% toluene removal at toluene inlet concentrations of 2-2.2 g x m(-3). Overall, the results show that the performance of the FEBR far exceeds that of currently used bioreactors for air pollution control.

  1. 76 FR 5319 - Revisions to the California State Implementation Plan, Santa Barbara Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-31

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Santa Barbara Air Pollution Control District, Placer County Air Pollution Control District, Antelope Valley Air Quality Management District, and Ventura County Air Pollution Control District AGENCY: Environmental Protection Agency...

  2. 76 FR 40660 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-11

    .... SUMMARY: EPA is proposing to approve revisions to the San Joaquin Valley Air Pollution Control District....0 for the following terms: Air Pollution Control Officer, Board, Environmental Protection Agency.... New Section 6.3 requires the SJVUAPCD Air Pollution Control Officer (APCO) to prepare and present...

  3. 75 FR 10690 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-09

    ... is finalizing approval of revisions to the San Joaquin Valley Air Pollution Control District (SJVAPCD...)(2)). List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control... Joaquin Valley Unified Air Pollution Control District. (1) Rule 4104, ``Reduction of Animal Matter,''...

  4. 76 FR 5277 - Revisions to the California State Implementation Plan, Santa Barbara Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-31

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Santa Barbara Air Pollution Control District, Antelope Valley Air Quality Management District, Ventura County Air Pollution Control District and Placer County Air Pollution Control District AGENCY: Environmental Protection Agency...

  5. 40 CFR 40.145-2 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.145-2 Federal Water Pollution Control Act. (a... or control of acid or other mine water pollution; and (2) That the State shall provide legal...

  6. 40 CFR 40.145-2 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.145-2 Federal Water Pollution Control Act. (a... or control of acid or other mine water pollution; and (2) That the State shall provide legal...

  7. 15 CFR 923.45 - Air and water pollution control requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Air and water pollution control....45 Air and water pollution control requirements. The program must incorporate, by reference or otherwise, all requirements established by the Federal Water Pollution Control Act, as amended (Clean...

  8. 40 CFR 40.140-3 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.140-3 Federal Water Pollution Control Act. (a... such safe water and such elimination or control of water pollution for all native villages in the...

  9. 40 CFR 40.140-3 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.140-3 Federal Water Pollution Control Act. (a... such safe water and such elimination or control of water pollution for all native villages in the...

  10. 40 CFR 40.140-3 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.140-3 Federal Water Pollution Control Act. (a... such safe water and such elimination or control of water pollution for all native villages in the...

  11. 40 CFR 40.140-3 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.140-3 Federal Water Pollution Control Act. (a... such safe water and such elimination or control of water pollution for all native villages in the...

  12. 40 CFR 40.145-2 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.145-2 Federal Water Pollution Control Act. (a... or control of acid or other mine water pollution; and (2) That the State shall provide legal...

  13. 14 CFR 1274.926 - Clean Air-Water Pollution Control Acts.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Clean Air-Water Pollution Control Acts. 1274... AGREEMENTS WITH COMMERCIAL FIRMS Other Provisions and Special Conditions § 1274.926 Clean Air-Water Pollution Control Acts. Clean Air-Water Pollution Control Acts July 2002 If this cooperative agreement or...

  14. 15 CFR 923.45 - Air and water pollution control requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 15 Commerce and Foreign Trade 3 2012-01-01 2012-01-01 false Air and water pollution control....45 Air and water pollution control requirements. The program must incorporate, by reference or otherwise, all requirements established by the Federal Water Pollution Control Act, as amended (Clean...

  15. 40 CFR 40.145-2 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.145-2 Federal Water Pollution Control Act. (a... or control of acid or other mine water pollution; and (2) That the State shall provide legal...

  16. 15 CFR 923.45 - Air and water pollution control requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 15 Commerce and Foreign Trade 3 2014-01-01 2014-01-01 false Air and water pollution control....45 Air and water pollution control requirements. The program must incorporate, by reference or otherwise, all requirements established by the Federal Water Pollution Control Act, as amended (Clean...

  17. 40 CFR 40.145-2 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.145-2 Federal Water Pollution Control Act. (a... or control of acid or other mine water pollution; and (2) That the State shall provide legal...

  18. 15 CFR 923.45 - Air and water pollution control requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 15 Commerce and Foreign Trade 3 2013-01-01 2013-01-01 false Air and water pollution control....45 Air and water pollution control requirements. The program must incorporate, by reference or otherwise, all requirements established by the Federal Water Pollution Control Act, as amended (Clean...

  19. 15 CFR 923.45 - Air and water pollution control requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 15 Commerce and Foreign Trade 3 2011-01-01 2011-01-01 false Air and water pollution control....45 Air and water pollution control requirements. The program must incorporate, by reference or otherwise, all requirements established by the Federal Water Pollution Control Act, as amended (Clean...

  20. 40 CFR Table 10 to Part 455 - List of Appropriate Pollution Control Technologies

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 31 2013-07-01 2013-07-01 false List of Appropriate Pollution Control...—List of Appropriate Pollution Control Technologies This table contains those pollutant control... wastewaters must include an emulsion breaking step. For PAIs whose technology is listed as...

  1. 40 CFR 1700.14 - Marine Pollution Control Device (MPCD) Performance Standards. [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Marine Pollution Control Device (MPCD... DISCHARGE STANDARDS FOR VESSELS OF THE ARMED FORCES Marine Pollution Control Device (MPCD) Performance Standards § 1700.14 Marine Pollution Control Device (MPCD) Performance Standards....

  2. 40 CFR 1700.14 - Marine Pollution Control Device (MPCD) Performance Standards. [Reserved

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Marine Pollution Control Device (MPCD... UNIFORM NATIONAL DISCHARGE STANDARDS FOR VESSELS OF THE ARMED FORCES Marine Pollution Control Device (MPCD) Performance Standards § 1700.14 Marine Pollution Control Device (MPCD) Performance Standards. [Reserved]...

  3. 26 CFR 1.169-1 - Amortization of pollution control facilities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 2 2011-04-01 2011-04-01 false Amortization of pollution control facilities. 1....169-1 Amortization of pollution control facilities. (a) Allowance of deduction—(1) In general. Under... amortization of the amortizable basis (as defined in § 1.169-3) of any certified pollution control facility...

  4. 40 CFR 1700.14 - Marine Pollution Control Device (MPCD) Performance Standards. [Reserved

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Marine Pollution Control Device (MPCD... DISCHARGE STANDARDS FOR VESSELS OF THE ARMED FORCES Marine Pollution Control Device (MPCD) Performance Standards § 1700.14 Marine Pollution Control Device (MPCD) Performance Standards....

  5. 40 CFR 1700.14 - Marine Pollution Control Device (MPCD) Performance Standards. [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Marine Pollution Control Device (MPCD... DISCHARGE STANDARDS FOR VESSELS OF THE ARMED FORCES Marine Pollution Control Device (MPCD) Performance Standards § 1700.14 Marine Pollution Control Device (MPCD) Performance Standards....

  6. 40 CFR 1700.14 - Marine Pollution Control Device (MPCD) Performance Standards. [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Marine Pollution Control Device (MPCD... DISCHARGE STANDARDS FOR VESSELS OF THE ARMED FORCES Marine Pollution Control Device (MPCD) Performance Standards § 1700.14 Marine Pollution Control Device (MPCD) Performance Standards....

  7. 26 CFR 1.169-1 - Amortization of pollution control facilities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Amortization of pollution control facilities. 1....169-1 Amortization of pollution control facilities. (a) Allowance of deduction—(1) In general. Under... amortization of the amortizable basis (as defined in § 1.169-3) of any certified pollution control facility...

  8. 26 CFR 1.169-1 - Amortization of pollution control facilities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 26 Internal Revenue 2 2012-04-01 2012-04-01 false Amortization of pollution control facilities. 1....169-1 Amortization of pollution control facilities. (a) Allowance of deduction—(1) In general. Under... amortization of the amortizable basis (as defined in § 1.169-3) of any certified pollution control facility...

  9. 26 CFR 1.169-1 - Amortization of pollution control facilities.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 26 Internal Revenue 2 2013-04-01 2013-04-01 false Amortization of pollution control facilities. 1....169-1 Amortization of pollution control facilities. (a) Allowance of deduction—(1) In general. Under... amortization of the amortizable basis (as defined in § 1.169-3) of any certified pollution control facility...

  10. 40 CFR Table 10 to Part 455 - List of Appropriate Pollution Control Technologies

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 31 2012-07-01 2012-07-01 false List of Appropriate Pollution Control...—List of Appropriate Pollution Control Technologies This table contains those pollutant control... wastewaters must include an emulsion breaking step. For PAIs whose technology is listed as...

  11. 26 CFR 1.169-1 - Amortization of pollution control facilities.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 26 Internal Revenue 2 2014-04-01 2014-04-01 false Amortization of pollution control facilities. 1....169-1 Amortization of pollution control facilities. (a) Allowance of deduction—(1) In general. Under... amortization of the amortizable basis (as defined in § 1.169-3) of any certified pollution control facility...

  12. Cysticercosis Control: Bringing Advances to the Field

    PubMed Central

    O’Neal, SE; Winthrop, KL; Gonzalez, AE

    2011-01-01

    Progress towards Taenia solium control is evident in the development of new technologies and in increasing regional coordination, yet disease eradication remains unlikely in the near future. In the meantime, translation of research advances into functioning control programs is necessary to address the ongoing disease burden in endemic areas. Multiple screening assays, effective treatments for both human and porcine infection, and vaccines blocking transmission to pigs are currently available. Strategies based on identification and treatment of T. solium adult tapeworms, as well as interventions that block cysticercosis acquisition in pigs have temporarily reduced transmission. Building on these successes with controlled community trials in varying endemic scenarios will drive progress towards regional elimination. PMID:21731303

  13. Coercive versus cooperative pollution control: Comparative study of state programs to reduce erosion and sedimentation pollution in urban areas

    NASA Astrophysics Data System (ADS)

    Burby, Raymond J.

    1995-05-01

    This article examines coercive and cooperative approaches to implementing state urban erosion and sedimentation pollution control programs. State administrators report serious shortfalls in their ability to control sources of pollution, but comparison of more and less successful programs provides evidence of what states can do to make programs more effective. Key ingredients for a successful state effort include the use of coercion with both the private sector and local government, adequate staffing, application of severe sanctions when violations of state standards are detected, and provision of technical assistance. Many state programs lack one or more of those elements, which explains their inability to adequately control urban erosion and sedimentation pollution.

  14. Simulation Of Advanced Train Control Systems

    NASA Astrophysics Data System (ADS)

    Craven, Paul; Oman, Paul

    This paper describes an Advanced Train Control System (ATCS) simulation environment created using the Network Simulator 2 (ns-2) discrete event network simulation system. The ATCS model is verified using ATCS monitoring software, laboratory results and a comparison with a mathematical model of ATCS communications. The simulation results are useful in understanding ATCS communication characteristics and identifying protocol strengths, weaknesses, vulnerabilities and mitigation techniques. By setting up a suite of ns-2 scripts, an engineer can simulate hundreds of possible scenarios in the space of a few seconds to investigate failure modes and consequences.

  15. Advanced nuclear plant control room complex

    DOEpatents

    Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

    1993-01-01

    An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

  16. An advanced field experimental design to assess plant tolerance to heavy metal pollution

    NASA Astrophysics Data System (ADS)

    Łopata, Barbara; Szarek-Łukaszewska, Grażyna; Babst-Kostecka, Alicja

    2016-04-01

    Only a limited number of vascular plant species can survive and reproduce in toxic metalliferous environments. Among these species, pseudometallophytes are particularly interesting, as their metallicolous (M) populations on metalliferous soils and non-metallicolous (NM) populations on non-metalliferous soils show very pronounced ecological differences. Pseudometallophytes thus provide excellent opportunities for multidisciplinary research to improve phytoremediation and phytomining. Numerous methods have been developed to investigate plant adaptation to metal pollution, the majority of which has been conducted under controlled laboratory conditions. Although these efforts have significantly advanced our understanding of mechanisms underlying metal tolerance in plants, populations must be reciprocally transplanted to clearly identify natural selection. Only then is it possible to test, whether the fitness of native plants is higher than that of nonnative populations and thereby prove local adaptation. Here, we present an enhanced field experimental design aimed at verification of local adaptation to habitats with different levels of heavy metal soil contamination. At two M and two NM sites, we established a total of 12 plots (4 sites x 3 plots each), removed the existing local vegetation, and collected soil samples for chemical analyses (5 samples per plot). Plant collection (N= 480) from all four selected populations was established under laboratory conditions prior to the transplant experiment. Genotypes were randomly distributed within each plot (240 x 270 cm) and planted along a regulary spaced grid (30x30cm cell size) in spring 2015. Measurements will start in spring 2016, by which time plants are expected to have acclimatized to the local conditions. For the two subsiquent years, growth, survival, fitness, life cycle and herbivory consumption will be monitored for each transplant. On a weekly basis, we will record: 1) pictures of each transplant to determine

  17. Advanced Wavefront Sensing and Control Testbed (AWCT)

    NASA Technical Reports Server (NTRS)

    Shi, Fang; Basinger, Scott A.; Diaz, Rosemary T.; Gappinger, Robert O.; Tang, Hong; Lam, Raymond K.; Sidick, Erkin; Hein, Randall C.; Rud, Mayer; Troy, Mitchell

    2010-01-01

    The Advanced Wavefront Sensing and Control Testbed (AWCT) is built as a versatile facility for developing and demonstrating, in hardware, the future technologies of wave front sensing and control algorithms for active optical systems. The testbed includes a source projector for a broadband point-source and a suite of extended scene targets, a dispersed fringe sensor, a Shack-Hartmann camera, and an imaging camera capable of phase retrieval wavefront sensing. The testbed also provides two easily accessible conjugated pupil planes which can accommodate the active optical devices such as fast steering mirror, deformable mirror, and segmented mirrors. In this paper, we describe the testbed optical design, testbed configurations and capabilities, as well as the initial results from the testbed hardware integrations and tests.

  18. Fate of mercury collected from air pollution control devices

    SciTech Connect

    Constance L. Senior; Susan Thorneloe; Bernine Khan; David Goss

    2009-07-15

    Mercury that enters a coal-fired power plant originates from the coal that is burned and leaves through the output streams, which include stack emissions and air pollution control (APC) residues (either in solid or liquid form). This article describes recent findings on the fate and environmental stability of mercury in coal combustion residues (CCRs) such as fly ash and solid products from flue gas desulfurization (FGD) scrubbers when either disposed or reused in agricultural, commercial, or engineering applications. 19 refs., 4 figs., 5 tabs.

  19. Optimum management scheme to control nonpoint pollution in Korea.

    PubMed

    Hwang, D-H; Choi, J-Y

    2007-01-01

    Comprehensive measures to control nonpoint source were developed by the Office of the Prime Minister, Korea in March 2004. These management measures present the government's policies and directions relating to nonpoint source management by 2020. However, the government has encountered difficulties since the government implemented such policies without preparing legal and institutional arrangements associated with nonpoint source management practices. Particularly, there was no legal system to manage the workplaces and construction sites that discharge the polluted runoff. To provide legal arrangements to achieve efficient implementation of the government's nonpoint source management policies, amendments to the "Water Quality Preservation Act" were proposed in the congress in March 2005 and took effect from April 2006. Subsequently, the nationally mandated nonpoint source control system was to be applied to such industries and construction sites. This paper attempts to propose the scope of the nonpoint source control system and effective strategies applied to the construction sites and industrial workplaces in Korea.

  20. Controlling sources of indoor air pollution through pollution prevention. Report for January 1994--May 1998

    SciTech Connect

    Leovic, K.W.; Whitaker, D.; Brockmann, C.; Bayer, C.; Sojka, P.

    1998-12-31

    The paper is an overview of EPA research into controlling sources of indoor air pollution through pollution prevention (P2). The research focused on four approaches for P2: (1) developing methods and tools that can be used by others to evaluate emissions from equipment or products; (2) developing generic P2 solutions to IAQ problems; (3) identifying high-emitting raw materials or components of products; and (4) evaluating claimed low-emitting materials. Test method guidelines for measuring emissions from office equipment were developed and then evaluated by testing four dry-process copiers in one chamber and conducting a four-laboratory evaluation using one of the copiers. For aerosol consumer products, measurement methods and models were developed that can be used to better understand aerosol behavior so that more efficacious and less toxic products can be developed. As a generic solution for improved IAQ through P2, an innovative spray nozzle for use with precharged aerosol containers was developed and evaluated. The new design allows for the reformulation of selected aerosol consumer products using water and air in place of volatile organic compound solvents and hydrocarbon propellants, respectively.

  1. Method oil shale pollutant sorption/NO.sub.x reburning multi-pollutant control

    DOEpatents

    Boardman, Richard D.; Carrington, Robert A.

    2008-06-10

    A method of decreasing pollutants produced in a combustion process. The method comprises combusting coal in a combustion chamber to produce at least one pollutant selected from the group consisting of a nitrogen-containing pollutant, sulfuric acid, sulfur trioxide, carbonyl sulfide, carbon disulfide, chlorine, hydroiodic acid, iodine, hydrofluoric acid, fluorine, hydrobromic acid, bromine, phosphoric acid, phosphorous pentaoxide, elemental mercury, and mercuric chloride. Oil shale particles are introduced into the combustion chamber and are combusted to produce sorbent particulates and a reductant. The at least one pollutant is contacted with at least one of the sorbent particulates and the reductant to decrease an amount of the at least one pollutant in the combustion chamber. The reductant may chemically reduce the at least one pollutant to a benign species. The sorbent particulates may adsorb or absorb the at least one pollutant. A combustion chamber that produces decreased pollutants in a combustion process is also disclosed.

  2. Field Operations and Enforcement Manual for Air Pollution Control. Volume I: Organization and Basic Procedures.

    ERIC Educational Resources Information Center

    Weisburd, Melvin I.

    The Field Operations and Enforcement Manual for Air Pollution Control, Volume I, explains in detail the following: sources and classification of pollutants; meteorological influence on air quality; the air pollution control agency; the field enforcement officer; the enforcement process; prosecuting violation; and inspection techniques including…

  3. 76 FR 298 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-04

    ... Valley Unified Air Pollution Control District (SJVUAPCD) portion of the California State Implementation......... 12/17/92 08/24/07 On September 17, 2007, the submittal for San Joaquin Valley Unified Air Pollution... require that fixed covers be equipped with a 95% efficient Air Pollution Control (APC) device. c....

  4. 78 FR 6736 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-31

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... taking direct final action to approve revisions to the Placer County Air Pollution Control District..., however, provide for Air Pollution Control Officer (APCO) discretion to allow burning on a No-Burn...

  5. 78 FR 37130 - Revisions to the California State Implementation Plan, San Diego Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-20

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, San Diego Air Pollution... taking direct final action to approve a revision to the San Diego Air Pollution Control District (SDAPCD... Part 52 Environmental protection, Air pollution control, Incorporation by reference,...

  6. 75 FR 18061 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Control of Air Pollution...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-09

    ... Air Pollution From Motor Vehicles AGENCY: Environmental Protection Agency (EPA). ACTION: Direct final... amend 30 TAC Chapter 114, Control of Air Pollution from Motor Vehicles. These revisions consist of the... to develop air pollution regulations and control strategies to ensure that air quality meets...

  7. 76 FR 26615 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-09

    .... SUMMARY: EPA is finalizing approval of revisions to the Imperial County Air Pollution Control District... various air pollution sources. We are approving local rules that regulate these emission sources under the... CFR Part 52 Environmental protection, Air pollution control, Incorporation by...

  8. 77 FR 2643 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-19

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... finalizing a limited approval and limited disapproval of revisions to the Placer County Air Pollution Control...) * * * (i) * * * (D) Placer County Air Pollution Control District (1) Rule 233, ``Biomass Boilers,''...

  9. 75 FR 2796 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-19

    ... is finalizing approval of revisions to the San Joaquin Valley Air Pollution Control District portion... topcoats; and that Ventura County Air Pollution Control District's (VCAPCD) rule has more stringent VOC...)(2)). List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution...

  10. 76 FR 75795 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-05

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... taking direct final action to approve revisions to the Placer County Air Pollution Control District... CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference, Reporting...

  11. 78 FR 53249 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-29

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... finalizing approval of revisions to the Placer County Air Pollution Control District (PCAPCD) portion of the... 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by...

  12. 48 CFR 452.236-74 - Control of Erosion, Sedimentation, and Pollution.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., Sedimentation, and Pollution. 452.236-74 Section 452.236-74 Federal Acquisition Regulations System DEPARTMENT OF....236-74 Control of Erosion, Sedimentation, and Pollution. As prescribed in 436.574, insert the following clause: Control of Erosion, Sedimentation, and Pollution (NOV 1996) (a) Operations shall...

  13. 48 CFR 436.574 - Control of erosion, sedimentation, and pollution.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., sedimentation, and pollution. 436.574 Section 436.574 Federal Acquisition Regulations System DEPARTMENT OF... 436.574 Control of erosion, sedimentation, and pollution. The contracting officer shall insert the clause at 452.236-74, Control of Erosion, Sedimentation and Pollution, if there is a need for...

  14. 48 CFR 436.574 - Control of erosion, sedimentation, and pollution.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., sedimentation, and pollution. 436.574 Section 436.574 Federal Acquisition Regulations System DEPARTMENT OF... 436.574 Control of erosion, sedimentation, and pollution. The contracting officer shall insert the clause at 452.236-74, Control of Erosion, Sedimentation and Pollution, if there is a need for...

  15. 48 CFR 436.574 - Control of erosion, sedimentation, and pollution.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., sedimentation, and pollution. 436.574 Section 436.574 Federal Acquisition Regulations System DEPARTMENT OF... 436.574 Control of erosion, sedimentation, and pollution. The contracting officer shall insert the clause at 452.236-74, Control of Erosion, Sedimentation and Pollution, if there is a need for...

  16. 48 CFR 436.574 - Control of erosion, sedimentation, and pollution.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., sedimentation, and pollution. 436.574 Section 436.574 Federal Acquisition Regulations System DEPARTMENT OF... 436.574 Control of erosion, sedimentation, and pollution. The contracting officer shall insert the clause at 452.236-74, Control of Erosion, Sedimentation and Pollution, if there is a need for...

  17. 48 CFR 436.574 - Control of erosion, sedimentation, and pollution.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., sedimentation, and pollution. 436.574 Section 436.574 Federal Acquisition Regulations System DEPARTMENT OF... 436.574 Control of erosion, sedimentation, and pollution. The contracting officer shall insert the clause at 452.236-74, Control of Erosion, Sedimentation and Pollution, if there is a need for...

  18. Can control of soil erosion mitigate water pollution by sediments?

    PubMed

    Rickson, R J

    2014-01-15

    The detrimental impact of sediment and associated pollutants on water quality is widely acknowledged, with many watercourses in the UK failing to meet the standard of 'good ecological status'. Catchment sediment budgets show that hill slope erosion processes can be significant sources of waterborne sediment, with rates of erosion likely to increase given predicted future weather patterns. However, linking on-site erosion rates with off-site impacts is complicated because of the limited data on soil erosion rates in the UK and the dynamic nature of the source-pathway-receptor continuum over space and time. Even so, soil erosion control measures are designed to reduce sediment production (source) and mobilisation/transport (pathway) on hill slopes, with consequent mitigation of pollution incidents in watercourses (receptors). The purpose of this paper is to review the scientific evidence of the effectiveness of erosion control measures used in the UK to reduce sediment loads of hill slope origin in watercourses. Although over 73 soil erosion mitigation measures have been identified from the literature, empirical data on erosion control effectiveness are limited. Baseline comparisons for the 18 measures where data do exist reveal erosion control effectiveness is highly variable over time and between study locations. Given the limitations of the evidence base in terms of geographical coverage and duration of monitoring, performance of the different measures cannot be extrapolated to other areas. This uncertainty in effectiveness has implications for implementing erosion/sediment risk reduction policies, where quantified targets are stipulated, as is the case in the EU Freshwater Fish and draft Soil Framework Directives. Also, demonstrating technical effectiveness of erosion control measures alone will not encourage uptake by land managers: quantifying the costs and benefits of adopting erosion mitigation is equally important, but these are uncertain and difficult to

  19. Can control of soil erosion mitigate water pollution by sediments?

    PubMed

    Rickson, R J

    2014-01-15

    The detrimental impact of sediment and associated pollutants on water quality is widely acknowledged, with many watercourses in the UK failing to meet the standard of 'good ecological status'. Catchment sediment budgets show that hill slope erosion processes can be significant sources of waterborne sediment, with rates of erosion likely to increase given predicted future weather patterns. However, linking on-site erosion rates with off-site impacts is complicated because of the limited data on soil erosion rates in the UK and the dynamic nature of the source-pathway-receptor continuum over space and time. Even so, soil erosion control measures are designed to reduce sediment production (source) and mobilisation/transport (pathway) on hill slopes, with consequent mitigation of pollution incidents in watercourses (receptors). The purpose of this paper is to review the scientific evidence of the effectiveness of erosion control measures used in the UK to reduce sediment loads of hill slope origin in watercourses. Although over 73 soil erosion mitigation measures have been identified from the literature, empirical data on erosion control effectiveness are limited. Baseline comparisons for the 18 measures where data do exist reveal erosion control effectiveness is highly variable over time and between study locations. Given the limitations of the evidence base in terms of geographical coverage and duration of monitoring, performance of the different measures cannot be extrapolated to other areas. This uncertainty in effectiveness has implications for implementing erosion/sediment risk reduction policies, where quantified targets are stipulated, as is the case in the EU Freshwater Fish and draft Soil Framework Directives. Also, demonstrating technical effectiveness of erosion control measures alone will not encourage uptake by land managers: quantifying the costs and benefits of adopting erosion mitigation is equally important, but these are uncertain and difficult to

  20. Emissions trading -- Market-based approaches offer pollution control incentives

    SciTech Connect

    Tombach, I.

    1994-06-01

    In the last several years, market-based'' strategies for achieving air quality goals have joined the traditional command-and-control'' approach to air pollution management. The premise behind market approaches is that the right'' to emit air pollutants provided by a permit has monetary value. A market-based approach provides facility operators with incentives to take advantage of the monetary value associated with reducing emissions below permitted levels. It has been recognized for some time that applying such a mechanism can be a cost-effective regional air quality management strategy. To date, economic incentives have been exploited somewhat in emissions reduction credit programs operating in non-attainment areas, but transactions have been tightly controlled by regulatory agencies. Two recently implemented programs have taken to the marketplace the management of emissions from specific sources. One is incorporated in the acid rain mitigation provisions of Title 4 of the Clean Air Act (CAA) Amendments; the other is the Regional Clean Air Incentives Market (RECLAIM), a program based on reducing ozone. Both Title 4 and RECLAIM are intended to achieve substantial reductions during the next decade in emissions of sulfur dioxide (SO[sub 2]) and oxides of nitrogens (NO[sub x]) from selected larger sources.

  1. Motorcycle pollution control in Taiwan, Republic of China

    SciTech Connect

    Chen, H.W.; Hsiao, H.C.; Walsh, M.P.

    1998-12-31

    The Taiwan EPA has developed a comprehensive approach to motor vehicle pollution control. Building on its early adoption of US `83 standards for light duty vehicles (starting July 1, 1990) it recently moved to US `87 requirements, which include the 0.2 gram per mile particulate standard, as of July 1, 1995. Heavy duty diesel particulate standards almost as stringent as US `90, 6.0 grams per brake horsepower hour NO{sub x} and 0.7 particulate, using the US transient test procedure, went into effect on July 1, 1993. It is intended that US`94 standards, 5.0 NO{sub x} and 0.25 particulate, will be adopted soon. Clearly the most distinctive feature of the Taiwan program, however, is its motorcycle control effort, reflecting the fact that motorcycles dominate the vehicle fleet and are a substantial source of emissions. This paper will summarize Taiwan`s extensive efforts to address this problem.

  2. The Advanced Controls Program at Oak Ridge National Laboratory

    SciTech Connect

    Knee, H.E.; White, J.D.

    1990-01-01

    The Oak Ridge National Laboratory (ORNL), under sponsorship of the US Department of Energy (DOE), is conducting research that will lead to advanced, automated control of new liquid-metal-reactor (LMR) nuclear power plants. Although this program of research (entitled the Advanced Controls Program'') is focused on LMR technology, it will be capable of providing control design, test, and qualification capability for other advanced reactor designs (e.g., the advanced light water reactor (ALWR) and high temperature gas-cooled reactor (HTGR) designs), while also benefiting existing nuclear plants. The Program will also have applicability to complex, non-nuclear process control environments (e.g., petrochemical, aerospace, etc.). The Advanced Controls Program will support capabilities throughout the entire plant design life cycle, i.e., from the initial interactive first-principle dynamic model development for the process, systems, components, and instruments through advanced control room qualification. The current program involves five principal areas of research activities: (1) demonstrations of advanced control system designs, (2) development of an advanced controls design environment, (3) development of advanced control strategies, (4) research and development (R D) in human-system integration for advanced control system designs, and (5) testing and validation of advanced control system designs. Discussion of the research in these five areas forms the basis of this paper. Also included is a description of the research directions of the program. 8 refs.

  3. Advanced Emissions Control Development Program: Phase III

    SciTech Connect

    G.T. Amrhein; R.T. Bailey; W. Downs; M.J. Holmes; G.A. Kudlac; D.A. Madden

    1999-07-01

    The primary objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. The project goal is to effectively control air toxic emissions through the use of conventional flue gas clean-up equipment such as electrostatic precipitators (ESPs), fabric filters (baghouses - BH), and wet flue gas desulfurization systems (WFGD). Development work concentrated on the capture of trace metals, fine particulate, hydrogen chloride and hydrogen fluoride, with an emphasis on the control of mercury. The AECDP project is jointly funded by the US Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (OCDO), and Babcock and Wilcox, a McDermott company (B and W). This report discusses results of all three phases of the AECDP project with an emphasis on Phase III activities. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on characterization of the emissions of mercury and other air toxics and the control of these emissions for typical operating conditions of conventional flue gas clean-up equipment. Some general comments that can be made about the control of air toxics while burning a high-sulfur bituminous coal are as follows: (1) particulate control devices such as ESP's and baghouses do a good job of removing non-volatile trace metals, (2) particulate control devices (ESPs and baghouses) effectively remove the particulate-phase mercury, but the particulate-phase mercury was only a small fraction of the total for the coals tested, (3) wet scrubbing can effectively remove hydrogen chloride and hydrogen fluoride, and (4) wet scrubbers show good potential for the removal of mercury when operated under certain conditions, however, for certain applications, system enhancements can be required to achieve high

  4. Advanced Noise Control Fan Aerodynamic Performance

    NASA Technical Reports Server (NTRS)

    Bozak, Richard F., Jr.

    2009-01-01

    The Advanced Noise Control Fan at the NASA Glenn Research Center is used to experimentally analyze fan generated acoustics. In order to determine how a proposed noise reduction concept affects fan performance, flow measurements can be used to compute mass flow. Since tedious flow mapping is required to obtain an accurate mass flow, an equation was developed to correlate the mass flow to inlet lip wall static pressure measurements. Once this correlation is obtained, the mass flow for future configurations can be obtained from the nonintrusive wall static pressures. Once the mass flow is known, the thrust and fan performance can be evaluated. This correlation enables fan acoustics and performance to be obtained simultaneously without disturbing the flow.

  5. EPA`s adaptive controls system research program for pollution prevention and clean technologies

    SciTech Connect

    Spiegel, R.J.; Chappell, P.J.; Miller, C.A.

    1994-12-31

    The current effort of EPA`s control systems research is concentrated in three areas: electric motors, wind turbines, and combustion technologies. In general, these projects are concerned with pollution prevention through enhanced efficiency of operation and pollution control through lower emission levels. Pioneering effort has been achieved in the application of fuzzy-logic-based controls in these areas. Based on the results of these projects, fuzzy logic has emerged as an important tool in environmental technology for pollution elimination and control.

  6. Controlled human exposures to ambient pollutant particles in susceptible populations

    EPA Science Inventory

    Epidemiologic studies have established an association between exposures to air pollution particles and human mortality and morbidity at concentrations of particles currently found in major metropolitan areas. The adverse effects of pollution particles are most prominent in suscep...

  7. Microwaves and their coupling to advanced oxidation processes: enhanced performance in pollutants degradation.

    PubMed

    Nascimento, Ulisses M; Azevedo, Eduardo B

    2013-01-01

    This review assesses microwaves (MW) coupled to advanced oxidation processes (AOPs) for pollutants degradation, as well as the basic theory and mechanisms of MW dielectric heating. We addressed the following couplings: MW/H2O2, MW/UV/H2O2, MW/Fenton, MW/US, and MW/UV/TiO2, as well as few studies that tested alternative oxidants and catalysts. Microwave Discharge Electrodeless Lamps (MDELs) are being extensively used with great advantages over ballasts. In their degradation studies, researchers generally employed domestic ovens with minor adaptations. Non-thermal effects and synergies between UV and MW radiation play an important role in the processes. Published papers so far report degradation enhancements between 30 and 1,300%. Unfortunately, how microwaves enhance pollutants is still obscure and real wastewaters scarcely studied. Based on the results surveyed in the literature, MW/AOPs are promising alternatives for treating/remediating environmental pollutants, whenever one considers high degradation yields, short reaction times, and small costs.

  8. Advances in development of transgenic plants for remediation of xenobiotic pollutants.

    PubMed

    Eapen, Susan; Singh, Sudhir; D'Souza, S F

    2007-01-01

    Phytoremediation-the use of plants for cleaning up of xenobiotic compounds-has received much attention in the last few years and development of transgenic plants tailored for remediation will further enhance their potential. Although plants have the inherent ability to detoxify some xenobiotic pollutants, they generally lack the catabolic pathway for complete degradation/mineralization of these compounds compared to microorganisms. Hence, transfer of genes involved in xenobiotic degradation from microbes/other eukaryotes to plants will further enhance their potential for remediation of these dangerous groups of compounds. Transgenic plants with enhanced potential for detoxification of xenobiotics such as trichloro ethylene, pentachlorophenol, trinitro toluene, glycerol trinitrate, atrazine, ethylene dibromide, metolachlor and hexahydro-1,3,5-trinitro-1,3,5-triazine are a few successful examples of utilization of transgenic technology. As more genes involved in xenobiotic metabolism in microorganisms/eukaryotes are discovered, it will lead to development of novel transgenic plants with improved potential for degradation of recalcitrant contaminants. Selection of suitable candidate plants, field testing and risk assessment are important considerations to be taken into account while developing transgenic plants for phytoremediation of this group of pollutants. Taking advantage of the advances in biotechnology and 'omic' technologies, development of novel transgenic plants for efficient phytoremediation of xenobiotic pollutants, field testing and commercialization will soon become a reality.

  9. Control Software for Advanced Video Guidance Sensor

    NASA Technical Reports Server (NTRS)

    Howard, Richard T.; Book, Michael L.; Bryan, Thomas C.

    2006-01-01

    Embedded software has been developed specifically for controlling an Advanced Video Guidance Sensor (AVGS). A Video Guidance Sensor is an optoelectronic system that provides guidance for automated docking of two vehicles. Such a system includes pulsed laser diodes and a video camera, the output of which is digitized. From the positions of digitized target images and known geometric relationships, the relative position and orientation of the vehicles are computed. The present software consists of two subprograms running in two processors that are parts of the AVGS. The subprogram in the first processor receives commands from an external source, checks the commands for correctness, performs commanded non-image-data-processing control functions, and sends image data processing parts of commands to the second processor. The subprogram in the second processor processes image data as commanded. Upon power-up, the software performs basic tests of functionality, then effects a transition to a standby mode. When a command is received, the software goes into one of several operational modes (e.g. acquisition or tracking). The software then returns, to the external source, the data appropriate to the command.

  10. Issue in pollution control: interplant cost differences and economies of scale.

    USGS Publications Warehouse

    Pittman, R.W.

    1981-01-01

    Seeks evidence concerning the issues of the relative efficiencies of different institutional arrangements for pollution control and the implications of control requirements for economies of scale and barriers to entry. Data is derived from the estimation of a production function for 30 pulp and paper mills in Wisconsin and Michigan. Concludes that the systematic differences in marginal treatment costs for different mills are evidence of serious inefficiencies resulting from the current (US) system of pollution control regulation. The positive association of pollution control intensity with economies of scale suggests that any pollution control regime has some negative allocational effects in this industry (and presumably others). -K.Turner

  11. Analysis of control methods: mercury and cadmium pollution.

    PubMed Central

    MacGregor, A

    1975-01-01

    Physical system conceptual models are developed to illustrate the various interconnecting pathways of metal flow. Economic use of mercury and cadmium, as representative toxic heavy metals, is inventoried, and the losses of each from the pathways of economic use are compared. Distinctions are made between high volume consumers and industries that are responsible for a large percent of total emissions or effluent loads. The pathways of the metals in the environment are traced via the conceptual models. A global mass balance is presented for mercury. The problem of high local concentrations vs. global metal flow is reviewed. Impacts of the metals on human health are categorized by type of effect. Available control strategies and abatement measures are evaluated with respect to the effectiveness of each on the problems of metal pollution, as illustrated by the physical models. PMID:1227855

  12. [Method for environmental management in paper industry based on pollution control technology simulation].

    PubMed

    Zhang, Xue-Ying; Wen, Zong-Guo

    2014-11-01

    To evaluate the reduction potential of industrial water pollutant emissions and to study the application of technology simulation in pollutant control and environment management, an Industrial Reduction Potential Analysis and Environment Management (IRPAEM) model was developed based on coupling of "material-process-technology-product". The model integrated bottom-up modeling and scenario analysis method, and was applied to China's paper industry. Results showed that under CM scenario, the reduction potentials of waster water, COD and ammonia nitrogen would reach 7 x 10(8) t, 39 x 10(4) t and 0.3 x 10(4) t, respectively in 2015, 13.8 x 10(8) t, 56 x 10(4) t and 0.5 x 10(4) t, respectively in 2020. Strengthening the end-treatment would still be the key method to reduce emissions during 2010-2020, while the reduction effect of structure adjustment would be more obvious during 2015-2020. Pollution production could basically reach the domestic or international advanced level of clean production in 2015 and 2020; the index of wastewater and ammonia nitrogen would basically meet the emission standards in 2015 and 2020 while COD would not.

  13. Redefining the importance of nitrate during haze pollution to help optimize an emission control strategy

    NASA Astrophysics Data System (ADS)

    Pan, Yuepeng; Wang, Yuesi; Zhang, Junke; Liu, Zirui; Wang, Lili; Tian, Shili; Tang, Guiqian; Gao, Wenkang; Ji, Dongsheng; Song, Tao; Wang, Yonghong

    2016-09-01

    Nitrate salts represent a major component of fine mode aerosols, which play an important role in air pollution worldwide. Based on on-line and off-line aerosol measurements in urban Beijing for both clean and haze conditions, we demonstrate that the absolute and relative concentrations of nitrate increased with visibility degradation (relative humidity), whereas the variations of organics tracked the patterns of mixing-layer height and temperature. We propose that the increase in the relative contribution of nitrate to PM1 observed during the early stages of haze pollution was due to new particle formation, whereas the nitrate formed in PM1-2.5 during the latter stages was due to heterogeneous formation and hygroscopic growth. The increasing trend of nitrate (and also sulfate and ammonium) but decreasing trends of organics during haze development, together with the increase of the NO2/SO2 molar ratio with increasing proximity to downtown Beijing and with visibility degradation, provide further evidence that controlling NOx emissions should be a priority for improving air quality in mega cities. Additional large-scale investigation is required to adequately characterize the regional features of NOx-induced haze pollution in China. Such studies may provide insight into the formation of critical nuclei or the subsequent growth of freshly nucleated particles and advance our understanding of the role of nitrate in new particle formation.

  14. 40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... initial air pollution control device inspection? (a) The initial air pollution control device inspection... startup. (b) Within 10 operating days following an air pollution control device inspection, all...

  15. 40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... initial air pollution control device inspection? (a) The initial air pollution control device inspection... startup. (b) Within 10 operating days following an air pollution control device inspection, all...

  16. 40 CFR 63.13 - Addresses of State air pollution control agencies and EPA Regional Offices.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Addresses of State air pollution... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES General Provisions § 63.13 Addresses of State air pollution control...

  17. 40 CFR 63.13 - Addresses of State air pollution control agencies and EPA Regional Offices.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 10 2014-07-01 2014-07-01 false Addresses of State air pollution... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES General Provisions § 63.13 Addresses of State air pollution control...

  18. 75 FR 1284 - Revisions to the California State Implementation Plan, Ventura County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-11

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Ventura County Air Pollution... finalizing approval of revisions to the Ventura County Air Pollution Control District (VCAPCD) portion of the...)(2)). List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution...

  19. 40 CFR 63.13 - Addresses of State air pollution control agencies and EPA Regional Offices.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Addresses of State air pollution... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES General Provisions § 63.13 Addresses of State air pollution control...

  20. 40 CFR 63.13 - Addresses of State air pollution control agencies and EPA Regional Offices.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Addresses of State air pollution... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES General Provisions § 63.13 Addresses of State air pollution control...

  1. 40 CFR 63.13 - Addresses of State air pollution control agencies and EPA Regional Offices.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 10 2012-07-01 2012-07-01 false Addresses of State air pollution... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES General Provisions § 63.13 Addresses of State air pollution control...

  2. Characterization of Coal Combustion Residues from Electric Utilities Using Wet Scrubbers for Multi-Pollutant Control

    EPA Science Inventory

    This report evaluates changes that may occur to coal combustion residues (CCRs) in response to changes in air pollution control technology at coal-fired power plants, which will reduce emissions from the flue gas stack by transferring pollutants to fly ash and other air pollution...

  3. A quantitative integrated assessment of pollution prevention achieved by integrated pollution prevention control licensing.

    PubMed

    Styles, David; O'Brien, Kieran; Jones, Michael B

    2009-11-01

    This paper presents an innovative, quantitative assessment of pollution avoidance attributable to environmental regulation enforced through integrated licensing, using Ireland's pharmaceutical-manufacturing sector as a case study. Emissions data reported by pharmaceutical installations were aggregated into a pollution trend using an Environmental Emissions Index (EEI) based on Lifecycle Assessment methodologies. Complete sectoral emissions data from 2001 to 2007 were extrapolated back to 1995, based on available data. Production volume data were used to derive a sectoral production index, and determine 'no-improvement' emission trends, whilst questionnaire responses from 20 industry representatives were used to quantify the contribution of integrated licensing to emission avoidance relative to these trends. Between 2001 and 2007, there was a 40% absolute reduction in direct pollution from 27 core installations, and 45% pollution avoidance relative to hypothetical 'no-improvement' pollution. It was estimated that environmental regulation avoided 20% of 'no-improvement' pollution, in addition to 25% avoidance under business-as-usual. For specific emissions, avoidance ranged from 14% and 30 kt a(-1) for CO(2) to 88% and 598 t a(-1) for SO(x). Between 1995 and 2007, there was a 59% absolute reduction in direct pollution, and 76% pollution avoidance. Pollution avoidance was dominated by reductions in emissions of VOCs, SO(x) and NO(x) to air, and emissions of heavy metals to water. Pollution avoidance of 35% was attributed to integrated licensing, ranging from between 8% and 2.9 t a(-1) for phosphorus emissions to water to 49% and 3143 t a(-1) for SO(x) emissions to air. Environmental regulation enforced through integrated licensing has been the major driver of substantial pollution avoidance achieved by Ireland's pharmaceutical sector - through emission limit values associated with Best Available Techniques, emissions monitoring and reporting requirements, and

  4. [Principle for strategic decision based on population health risk in emergence environmental cadmium pollution control].

    PubMed

    Shang, Qi

    2012-05-01

    The principles for strategic decision in emergence environmental pollution control was summarized based on population health risk and features of emergence events of environmental cadmium pollution. Main task and strategies for the events control was suggested in emergency treatment and post-event for water and soil cadmium pollution respectively. The work, monitoring method, key problems for both environment cadmium pollution and human health risk, and main content of health education for cadmium exposure people was proposed in follow-up action, at meanwhile, achievements of study on human health effects caused by environmental cadmium pollution was introduced briefly over recent years.

  5. Structureborne noise control in advanced turboprop aircraft

    NASA Astrophysics Data System (ADS)

    Loeffler, Irvin J.

    1987-01-01

    Structureborne noise is discussed as a contributor to propeller aircraft interior noise levels that are nonresponsive to the application of a generous amount of cabin sidewall acoustic treatment. High structureborne noise levels may jeopardize passenger acceptance of the fuel-efficient high-speed propeller transport aircraft designed for cruise at Mach 0.65 to 0.85. These single-rotation tractor and counter-rotation tractor and pusher propulsion systems will consume 15 to 30 percent less fuel than advanced turbofan systems. Structureborne noise detection methodologies and the importance of development of a structureborne noise sensor are discussed. A structureborne noise generation mechanism is described in which the periodic components or propeller swirl produce periodic torques and forces on downstream wings and airfoils that are propagated to the cabin interior as noise. Three concepts for controlling structureborne noise are presented: (1) a stator row swirl remover, (2) selection of a proper combination of blade numbers in the rotor/stator system of a single-rotation propeller, and the rotor/rotor system of a counter-rotation propeller, and (3) a tuned mechanical absorber.

  6. Operation and Maintenance of Water Pollution Control Facilities: A WPCF White Paper.

    ERIC Educational Resources Information Center

    Hill, William R.; And Others

    1979-01-01

    Presented are the recommendations of the Water Pollution Control Federation for operation and maintenance consideration during the planning design, construction, and operation of wastewater treatment facilities. (CS)

  7. Impact of Advance Control on Microturbine Generation System Performance

    NASA Astrophysics Data System (ADS)

    Kamil Mat Hussin, Ahmad; Zamri Che Wanik, Mohd

    2013-06-01

    Advance control employed in microturbine generation system (MTGS) is expected to improve its performance in responding to grid faults. This paper compares the effect of advance control of MTGS power conversion topology on the performance in riding through the grid faults. The analysis and investigation study through simulation shows there is no significant different on MTGS output performance even advance control is employed for its rectifier.

  8. 77 FR 52341 - Information Collection Activity: Subpart C, Pollution Prevention and Control; Submitted for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-29

    ... Prevention and Control; Submitted for Office of Management and Budget (OMB) Review; Comment Request ACTION... the paperwork requirements in the regulations under Subpart C, Pollution Prevention and Control. This... information. SUPPLEMENTARY INFORMATION: Title: 30 CFR 250, Subpart C, Pollution Prevention and Control....

  9. Contemporary and futuristic views of pollution control devices in foundries.

    PubMed

    Krishnaraj, R

    2015-10-01

    Foundry practices are used in contemporary world to produce large volume of components and products. Foundry practices involve the melting of metals and pouring the molten metal into the cavities called molds. On solidification, the metals which assume the shape of molds are removed as castings. Foundries that employ these practices were growing in large number till the middle part of the twentieth century in the world. After the middle part of the twentieth century, the world community begun to realize that, foundries were emitting pollutants which were affecting the health of humans. In order to overcome this situation, several countries in the world promulgated laws stipulating the maximum level of pollutants that can emit by foundries. These laws affected the functioning and growth of foundries. In order to sustain amidst these constraints, foundries begun to install energy efficient melting technologies and pollution control devices (PCDs). In this back ground, this paper reports to assess the contemporary scenario and project the future needs for sustaining the foundries. During the conduct of this literature review, it was discernable that, research papers have reported three categories of researches. In the first category of research papers, the researches reporting the achievement of cleaner production technologies in foundries using PCDs have appeared. In the second category of research papers, the application of cleaner production technology in foundries located in different countries has been examined. In the third category of research papers, the application of efficient melting technologies and PCDs in different clusters of foundries located in different parts of world has been explored. Subsequently implementation technics of Environmental Management System in cleaner production technics in foundries has been described the analysis of the information and knowledge drawn from these three categories of papers has revealed that, researches exploring the

  10. 40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control device inspection), you must complete the air pollution...

  11. 40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution...

  12. 40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution...

  13. 40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... pollution control device inspection? (a) The initial air pollution control device inspection must be... meeting the amended emission limitations. (b) Within 10 operating days following an air pollution...

  14. 40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control device inspection), you must complete the air pollution...

  15. [Spatial heterogeneity and classified control of agricultural non-point source pollution in Huaihe River Basin].

    PubMed

    Zhou, Liang; Xu, Jian-Gang; Sun, Dong-Qi; Ni, Tian-Hua

    2013-02-01

    Agricultural non-point source pollution is of importance in river deterioration. Thus identifying and concentrated controlling the key source-areas are the most effective approaches for non-point source pollution control. This study adopts inventory method to analysis four kinds of pollution sources and their emissions intensity of the chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in 173 counties (cities, districts) in Huaihe River Basin. The four pollution sources include livestock breeding, rural life, farmland cultivation, aquacultures. The paper mainly addresses identification of non-point polluted sensitivity areas, key pollution sources and its spatial distribution characteristics through cluster, sensitivity evaluation and spatial analysis. A geographic information system (GIS) and SPSS were used to carry out this study. The results show that: the COD, TN and TP emissions of agricultural non-point sources were 206.74 x 10(4) t, 66.49 x 10(4) t, 8.74 x 10(4) t separately in Huaihe River Basin in 2009; the emission intensity were 7.69, 2.47, 0.32 t.hm-2; the proportions of COD, TN, TP emissions were 73%, 24%, 3%. The paper achieves that: the major pollution source of COD, TN and TP was livestock breeding and rural life; the sensitivity areas and priority pollution control areas among the river basin of non-point source pollution are some sub-basins of the upper branches in Huaihe River, such as Shahe River, Yinghe River, Beiru River, Jialu River and Qingyi River; livestock breeding is the key pollution source in the priority pollution control areas. Finally, the paper concludes that pollution type of rural life has the highest pollution contribution rate, while comprehensive pollution is one type which is hard to control.

  16. Molecular perspectives and recent advances in microbial remediation of persistent organic pollutants.

    PubMed

    Chakraborty, Jaya; Das, Surajit

    2016-09-01

    Nutrition and pollution stress stimulate genetic adaptation in microorganisms and assist in evolution of diverse metabolic pathways for their survival on several complex organic compounds. Persistent organic pollutants (POPs) are highly lipophilic in nature and cause adverse effects to the environment and human health by biomagnification through the food chain. Diverse microorganisms, harboring numerous plasmids and catabolic genes, acclimatize to these environmentally unfavorable conditions by gene duplication, mutational drift, hypermutation, and recombination. Genetic aspects of some major POP catabolic genes such as biphenyl dioxygenase (bph), DDT 2,3-dioxygenase, and angular dioxygenase assist in degradation of biphenyl, organochlorine pesticides, and dioxins/furans, respectively. Microbial metagenome constitutes the largest genetic reservoir with miscellaneous enzymatic activities implicated in degradation. To tap the metabolic potential of microorganisms, recent techniques like sequence and function-based screening and substrate-induced gene expression are proficient in tracing out novel catabolic genes from the entire metagenome for utilization in enhanced biodegradation. The major endeavor of today's scientific world is to characterize the exact genetic mechanisms of microbes for bioremediation of these toxic compounds by excavating into the uncultured plethora. This review entails the effect of POPs on the environment and involvement of microbial catabolic genes for their removal with the advanced techniques of bioremediation. PMID:27234838

  17. The U.S. and Environmental Pollution Control

    ERIC Educational Resources Information Center

    Newill, Vaun A.

    1974-01-01

    Background concerning legislation and development of environmental programs is detailed in the areas of air pollution, water pollution, pesticides, and multimedia toxic substances. Each section contains a discussion of scientific knowledge, health effects, costs, proposed standards, and possible approaches to the problems. (LS)

  18. Constructed wetlands to control nonpoint-source pollution

    SciTech Connect

    Wengrzynek, R.L.

    1991-01-01

    The use of land for agriculture, urban development, and recreational purposes results in pollution that has potential to contaminate groundwater, streams, lakes and oceans. Aquatic ecosystems can be damaged by even small amounts of pollutants in runoff during storms and by cumulative impacts of chronic, low levels of pollution. Nutrients, pesticides and sediments can have long term effects on the ecosystems. The instant invention using constructed wetlands has been particularly useful for purposes of protecting ecosystems from untoward effects of nonpoint source pollution. The construct, containing in hydraulic order a sediment basin, level-lip spreader, grassy filter, wetland, and deep pond can be used to remove pollutants from nonpoint source runoff. Wetlands are planted with vegetation that encourages growth of aerobic and anaerobic bacteria, which are helpful in removing and detoxifying contaminants.

  19. A rapid approach to rational water pollution control strategies.

    PubMed

    Economopoulos, A P

    1996-10-01

    The formulation of rational wastewater control strategies is becoming increasingly important in many countries where, exploding urbanization, industrialization and/or tourism, often combined with improved standards of living and better awareness of the environmental problems, are resulting in enlarged pollution problems, but also in the availability of expanding financial resources for environmental protection. However, more often than one tends to believe, lack of planning, or planning with limited understanding of the principles involved, has resulted in solutions that are both expensive and incapable of addressing the key problems.As rigorous planning is extremely resource intensive, and for this reason impractical for most study areas, the development of a much simplified analysis procedure, capable of generating rational, near-optimum, strategies and detailed action programs, is required, if proper environmental management is to be widely practiced.In an effort to achieve the above objectives, a systems analysis approach is selected as the most suitable at rationalizing the allocation of available resources and at producing detailed action programs that promote implementation. In the context of this approach, new, easy to use models have been developed, while others, have been selected, adapted and streamlined in their use. The entire problem analysis and strategy synthesis procedures have thus been simplified and defined to a degree appropriate for widespread use, and the resultant procedure is actively promoted by WHO and UNEP.

  20. A rapid approach to rational water pollution control strategies.

    PubMed

    Economopoulos, A P

    1996-10-01

    The formulation of rational wastewater control strategies is becoming increasingly important in many countries where, exploding urbanization, industrialization and/or tourism, often combined with improved standards of living and better awareness of the environmental problems, are resulting in enlarged pollution problems, but also in the availability of expanding financial resources for environmental protection. However, more often than one tends to believe, lack of planning, or planning with limited understanding of the principles involved, has resulted in solutions that are both expensive and incapable of addressing the key problems.As rigorous planning is extremely resource intensive, and for this reason impractical for most study areas, the development of a much simplified analysis procedure, capable of generating rational, near-optimum, strategies and detailed action programs, is required, if proper environmental management is to be widely practiced.In an effort to achieve the above objectives, a systems analysis approach is selected as the most suitable at rationalizing the allocation of available resources and at producing detailed action programs that promote implementation. In the context of this approach, new, easy to use models have been developed, while others, have been selected, adapted and streamlined in their use. The entire problem analysis and strategy synthesis procedures have thus been simplified and defined to a degree appropriate for widespread use, and the resultant procedure is actively promoted by WHO and UNEP. PMID:24193733

  1. Air pollution control and waste management in a new world

    SciTech Connect

    McIlvaine, R.W. )

    1993-03-01

    The McIlvaine Co. has been preparing forecasts for the March issue of the [open quotes]Journal of Air and Waste Management Association[close quotes] for many years. Reviewing past forecasts reveals a consistent pattern; the forecasts have generally been accurate when governmental and industrial environmental policies have been rational, but some major errors in forecasting have resulted from unanticipated irrational governmental policies. The author begins this article by confessing some of his company's past forecasting errors, attributing them to the false assumption of a rational government policy. He then proceeds to base the new forecast on a rational proactive government policy. The forecast offers a program of renewal and hope. The author discusses the program in relation to utility waste handling, particulate emissions, global warming, spending on pollution control equipment, and US investment in air toxics reduction for 1993. The administration at this point gives every indication that this forecast is justified. This view is strengthened by the observation the US Vice President Gore understands the importance of the role that information will play in future environmental actions. 7 figs.

  2. 40 CFR 450.23 - Effluent limitations reflecting the best conventional pollutant control technology (BCT).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... limitations reflecting the best conventional pollutant control technology (BCT). Except as provided in 40 CFR... best conventional pollutant control technology (BCT). 450.23 Section 450.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) CONSTRUCTION...

  3. 40 CFR 450.23 - Effluent limitations reflecting the best conventional pollutant control technology (BCT).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... the best conventional pollutant control technology (BCT). Except as provided in 40 CFR 125.30 through... best conventional pollutant control technology (BCT). 450.23 Section 450.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS CONSTRUCTION AND DEVELOPMENT...

  4. 40 CFR 450.23 - Effluent limitations reflecting the best conventional pollutant control technology (BCT).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... the best conventional pollutant control technology (BCT). Except as provided in 40 CFR 125.30 through... best conventional pollutant control technology (BCT). 450.23 Section 450.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS CONSTRUCTION AND DEVELOPMENT...

  5. 40 CFR 450.23 - Effluent limitations reflecting the best conventional pollutant control technology (BCT).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... limitations reflecting the best conventional pollutant control technology (BCT). Except as provided in 40 CFR... best conventional pollutant control technology (BCT). 450.23 Section 450.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) CONSTRUCTION...

  6. 40 CFR Table 10 to Part 455 - List of Appropriate Pollution Control Technologies

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Technologies 10 Table 10 to Part 455 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Appropriate Pollution Control Technologies This table contains those pollutant control technologies, such as... estimating compliance costs on a PAI specific basis. In general, these treatment technologies have...

  7. 77 FR 73392 - Revisions to the California State Implementation Plan, Monterey Bay Unified Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-10

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Monterey Bay Unified Air Pollution Control District AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA is proposing to approve revisions to the Monterey Bay Unified Air Pollution Control...

  8. 75 FR 56942 - Revisions to the California State Implementation Plan, San Diego County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-17

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, San Diego County Air Pollution Control District AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA is proposing to approve revisions to the San Diego Air Pollution Control District...

  9. 78 FR 896 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-07

    ... is finalizing approval of revisions to the Imperial County Air Pollution Control District (ICAPCD...)(2)). List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Imperial County...

  10. 75 FR 27975 - Revisions to the California State Implementation Plan; Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-19

    ...: EPA is proposing to approve revisions to the Imperial County Air Pollution Control District (ICAPCD... of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Intergovernmental... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan; Imperial County...

  11. 75 FR 18142 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Control of Air Pollution...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-09

    ... AGENCY 40 CFR Part 52 Approval and Promulgation of Air Quality Implementation Plans; Texas; Control of Air Pollution From Motor Vehicles AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... Title 30 of the Texas Administrative Code (TAC), Chapter 114, Control of Air Pollution from...

  12. 76 FR 76046 - Interim Final Determination To Defer Sanctions, San Joaquin Valley Unified Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-06

    ... approval of revisions to the San Joaquin Valley Unified Air Pollution Control District (SJVUAPCD or... Valley Unified Air Pollution Control District (``SJVUAPCD'' or ``District'') Rules 2020 (Exemptions) and... AGENCY 40 CFR Part 52 Interim Final Determination To Defer Sanctions, San Joaquin Valley Unified...

  13. 76 FR 17347 - Revision to the California State Implementation Plan, Great Basin Unified Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-29

    ...) * * * (D) Great Basin Unified Air Pollution Control District (1) Rule 201, ``Exemptions,'' adopted on... AGENCY 40 CFR Part 52 Revision to the California State Implementation Plan, Great Basin Unified Air Pollution Control District CFR Correction In Title 40 of the Code of Federal Regulations, Part 52 (Sec....

  14. 75 FR 45082 - Revisions to the California State Implementation Plan, Santa Barbara County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-02

    ... Air Pollution Control District (SBCAPCD) portion of the California State Implementation Plan (SIP... Preamble for the Implementation of Title I of the Clean Air Act Amendments of 1990'', 57 FR 13498, April 16... Environmental protection, Air pollution control, Intergovernmental relations, Nitrogen dioxide, Ozone,...

  15. 77 FR 25109 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-27

    ...: EPA is proposing to approve revisions to the Imperial County Air Pollution Control District (ICAPCD... Implementation of Title I of the Clean Air Act Amendments of 1990,'' 59 FR 41998 (August 16, 1994). 5. ``PM-10... of Subjects in 40 CFR Part 52 Air pollution control, Environmental protection,...

  16. 76 FR 45199 - Interim Final Determination To Defer Sanctions, San Joaquin Valley Unified Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-28

    ... of revisions to the San Joaquin Valley Unified Air Pollution Control District (SJVUAPCD) portion of... Subjects in 40 CFR Part 52 Environmental protection, Air pollution control, Incorporation by reference... AGENCY 40 CFR Part 52 Interim Final Determination To Defer Sanctions, San Joaquin Valley Unified...

  17. 75 FR 2079 - Revisions to the California State Implementation Plan, San Joaquin Valley Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ... facilities. Also, please see our response to CPF comment 3. B. San Joaquin Valley Air Pollution Control...) San Joaquin Valley Unified Air Pollution Control District. (1) Rule 4570, ``Confined Animal Facilities... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, San Joaquin Valley...

  18. 78 FR 23677 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-22

    ... is finalizing approval of revisions to the Imperial County Air Pollution Control District (ICAPCD... Air Pollution Control District (SJVAPCD). Response #4--The comment does not identify and we are not... submittal and review process such as contained in SJVAPCD Rule 4550 and Great Basin Unified Air...

  19. 40 CFR 434.74 - Effluent limitations attainable by application of the best conventional pollutant control...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Effluent limitations attainable by application of the best conventional pollutant control technology (BCT). Except as provided in 40 CFR 125.30 through 125.32 and 434.72(b)(2), a pre-existing discharge must comply... application of the best conventional pollutant control technology (BCT). 434.74 Section 434.74 Protection...

  20. 75 FR 24406 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-05

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution Control District, Sacramento Metropolitan Air Quality Management District, San Joaquin Valley Unified Air Pollution Control District, and South Coast Air Quality Management District AGENCY: Environmental...

  1. 75 FR 24544 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-05

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution Control District, Sacramento Metropolitan Air Quality Management District, San Joaquin Valley Unified Air Pollution Control District, and South Coast Air Quality Management District AGENCY: Environmental...

  2. 40 CFR 450.23 - Effluent limitations reflecting the best conventional pollutant control technology (BCT).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... limitations reflecting the best conventional pollutant control technology (BCT). Except as provided in 40 CFR... best conventional pollutant control technology (BCT). 450.23 Section 450.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) CONSTRUCTION...

  3. 40 CFR 40.140-3 - Federal Water Pollution Control Act.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Federal Water Pollution Control Act. 40... FEDERAL ASSISTANCE RESEARCH AND DEMONSTRATION GRANTS § 40.140-3 Federal Water Pollution Control Act. (a... contribute to the development or demonstration of a new or improved method of treating industrial wastes...

  4. Energy technology characterizations handbook: Environmental pollution and control factors, third edition

    NASA Astrophysics Data System (ADS)

    1983-03-01

    Energy technologies and pollution control technologies are reviewed. Technology characterizations are given for the following energy sources: nuclear energy, synthetic fuels, coal, petroleum, natural gas, solar energy, geothermal energy, and hydroelectric energy. Air, water, and solid waste pollution control devices and mechanisms are presented for coal-fired power plants and industrial boilers and for synthetic fuel production from coal and oil shale.

  5. 78 FR 58460 - Revision of Air Quality Implementation Plan; California; Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... Pollution Control District and Feather River Air Quality Management District; Stationary Source Permits... California as a revision to the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portion of the California State Implementation Plan (SIP)....

  6. 78 FR 12243 - Interim Final Determination To Stay and Defer Sanctions, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-22

    ... Pollution Control District and Feather River Air Quality Management District AGENCY: Environmental... proposed approval of a revision to the Placer County Air Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portion of the California State Implementation Plan...

  7. 76 FR 58835 - Information Collection Activity: Revision for Subpart C, Pollution Prevention and Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-22

    ... Bureau of Ocean Energy Management, Regulation and Enforcement (BOEMRE) Information Collection Activity: Revision for Subpart C, Pollution Prevention and Control; Submitted for Office of Management and Budget..., Pollution Prevention and Control. This notice also provides the public a second opportunity to comment...

  8. [Study on feasible emission control level of air pollutions for cement industry ].

    PubMed

    Ren, Chun; Jiang, Mei; Zou, Lan; Li, Xiao-qian; Wei, Yu-xia; Zhao, Guo-hua; Zhang, Guo-ning

    2014-09-01

    The revised National Emission Standard of Air Pollutions for Cement Industry has been issued, which will be effective for the new enterprises and the existing enterprises on Mar. 1st, 2014 and July 1st, 2015, respectively. In the process of revision, the key technical issues on determination of standard limits was how to determine the feasible emission control level of air pollutions. Feasible emission control requirements were put forward, according to air pollutants emission, technologies, environmental management requirements and foreign standards, etc. The main contents of the revised standard include expanding the scope of application, increasing the pollutants, improving the particulate and NO emissions control level, and increasing special emission limits applied to key areas of air pollutants. The standard will become the gripper of pollution prevention, total emission reduction, structural adjustment and optimization of the layout, and will promote scientific and technical progression for the cement industry.

  9. Noise Pollution Control System in the Hospital Environment

    NASA Astrophysics Data System (ADS)

    Figueroa Gallo, LM; Olivera, JM

    2016-04-01

    Problems related to environmental noise are not a new subject, but they became a major issue to solve because of the increasing, in complexity and intensity, of human activities due technological advances. Numerous international studies had dealt with the exposure of critical patients to noisy environment such as the Neonatal Intensive Care Units; their results show that there are difficulties in the organization in the developing brain, it can damage the delicate auditory structures and can cause biorhythm disorders, specially in preterm infants. The objective of this paper is to present the development and implementation of a control system that includes technical-management-training aspects to regulate the levels of specific noise sources in the neonatal hospitalization environment. For this purpose, there were applied different tools like: observations, surveys, procedures, an electronic control device and a training program for a Neonatal Service Unit. As a result, all noise sources were identified -some of them are eliminable-; all the service stable staff categories participated voluntarily; environmental noise measurements yielded values between 62.5 and 64.6 dBA and maximum were between 86.1 and 89.7 dBA; it was designed and installed a noise control device and the staff is being trained in noise reduction best practices.

  10. Traffic improvement and transportation pollution control in Xiamen

    SciTech Connect

    Dongxing Yuan; Zilin, Wu

    1996-12-31

    in this paper, the urban traffic improvement and transportation control in Xiamen are highlighted. Xiamen is a port city and an economical special zone of China. As the economy grows, the transportation is developing dramatically and becoming the key for further economic development. The air quality is threatened by the rapid growth of the vehicles in the city. The most urgent task in improving urban traffic is to establish a sound traffic system. The municipal government takes great effort to improve the traffic condition, as well as to reduce green house gases and protect air environment. Some management and technical measures are carried out. Those management measures are mainly as follows: (1) systematic planning of the city arrangement and city functional division, and integrated planning of the urban roads system, (2) putting great emphasis on tail gas monitoring and management, and (3) establishing optimized utilization of motor vehicles. Those included in the main technical measures are (1) making the roads clear, (2) enlarging traffic capacity, and (3) developing the public transport. The most urgent task in improving urban traffic is to establish a sound traffic system. The city municipal government and Transportation Management Bureau plan to make a series of reforms to improve the urban traffic condition, such as building high quality road around the city, reducing the number of one way roads and replacing gasoline buses with electric buses. An optimized traffic system of Xiamen, taking public transport as the main means, is the key to meet the needs of both traffic improvement and urban transportation pollution control.

  11. Application of Advanced Process Control techniques to a pusher type reheating furnace

    NASA Astrophysics Data System (ADS)

    Zanoli, S. M.; Pepe, C.; Barboni, L.

    2015-11-01

    In this paper an Advanced Process Control system aimed at controlling and optimizing a pusher type reheating furnace located in an Italian steel plant is proposed. The designed controller replaced the previous control system, based on PID controllers manually conducted by process operators. A two-layer Model Predictive Control architecture has been adopted that, exploiting a chemical, physical and economic modelling of the process, overcomes the limitations of plant operators’ mental model and knowledge. In addition, an ad hoc decoupling strategy has been implemented, allowing the selection of the manipulated variables to be used for the control of each single process variable. Finally, in order to improve the system flexibility and resilience, the controller has been equipped with a supervision module. A profitable trade-off between conflicting specifications, e.g. safety, quality and production constraints, energy saving and pollution impact, has been guaranteed. Simulation tests and real plant results demonstrated the soundness and the reliability of the proposed system.

  12. Household Air Pollution Exposures of Pregnant Women Receiving Advanced Combustion Cookstoves in India: Implications for Intervention

    PubMed Central

    Balakrishnan, Kalpana; Sambandam, Sankar; Ghosh, Santu; Mukhopadhyay, Krishnendu; Vaswani, Mayur; Arora, Narendra K.; Jack, Darby; Pillariseti, Ajay; Bates, Michael N.; Smith, Kirk R.

    2016-01-01

    BACKGROUND Household air pollution (HAP) resulting from the use of solid cooking fuels is a leading contributor to the burden of disease in India. Advanced combustion cookstoves that reduce emissions from biomass fuels have been considered potential interventions to reduce this burden. Relatively little effort has been directed, however, to assessing the concentration and exposure changes associated with the introduction of such devices in households. OBJECTIVES The aim of this study was to describe HAP exposure patterns in pregnant women receiving a forced-draft advanced combustion cookstove (Philips model HD 4012) in the SOMAARTH Demographic Development & Environmental Surveillance Site (DDESS) Palwal District, Haryana, India. The monitoring was performed as part of a feasibility study to inform a potential large-scale HAP intervention (Newborn Stove trial) directed at pregnant women and newborns. METHODS This was a paired comparison exercise study with measurements of 24-hour personal exposures and kitchen area concentrations of carbon monoxide (CO) and particulate matter less than 2.5 μm in aerodynamic diameter (PM2.5), before and after the cookstove intervention. Women (N = 65) were recruited from 4 villages of SOMAARTH DDESS. Measurements were performed between December 2011 and March 2013. Ambient measurements of PM2.5 were also performed throughout the study period. FINDINGS Measurements showed modest improvements in 24-hour average concentrations and exposures for PM2.5 and CO (ranging from 16% to 57%) with the use of the new stoves. Only those for CO showed statistically significant reductions. CONCLUSION Results from the present study did not support the widespread use of this type of stove in this population as a means to reliably provide health-relevant reductions in HAP exposures for pregnant women compared with open biomass cookstoves. The feasibility assessment identified multiple factors related to user requirements and scale of adoption within

  13. Process for control of pollutants generated during coal gasification

    DOEpatents

    Frumerman, Robert; Hooper, Harold M.

    1979-01-01

    The present invention is directed to an improvement in the coal gasification process that effectively eliminates substantially all of the environmental pollutants contained in the producer gas. The raw producer gas is passed through a two-stage water scrubbing arrangement with the tars being condensed essentially water-free in the first stage and lower boiling condensables, including pollutant laden water, being removed in the second stage. The pollutant-laden water is introduced into an evaporator in which about 95 percent of the water is vaporized and introduced as steam into the gas producer. The condensed tars are combusted and the resulting products of combustion are admixed with the pollutant-containing water residue from the evaporator and introduced into the gas producer.

  14. Open architecture controllers for advanced manufacturing

    SciTech Connect

    Gore, R.A.

    1994-03-01

    The application of intelligent control systems to the real world of machining and manufacturing will benefit form the presence of open architecture control systems on the machines or the processes. The ability to modify the control system as the process or product changes can be essential to the success of the application of neural net or fuzzy logic controllers. The effort at Los Alamos to obtain a commercially available open architecture machine tool controller is described.

  15. Historical analysis of SO{sub 2} pollution control policies in China

    SciTech Connect

    Gao, C.L.; Yin, H.Q.; Ai, N.S.; Huang, Z.W.

    2009-03-15

    Coal is not only an important energy source in China but also a major source of air pollution. Because of this, China's national sulfur dioxide (SO{sub 2}) emissions have been the highest in the world for many years, and since the 1990s, the territory of China's south and southwest has become the third largest acid-rain-prone region in the world. In order to control SO{sub 2} emissions, the Chinese government has formulated and promulgated a series of policies and regulations, but it faces great difficulties in putting them into practice. In this retrospective look at the history of SO{sub 2} control in China, we found that Chinese SO{sub 2} control policies have become increasingly strict and rigid. We also found that the environmental policies and regulations are more effective when central officials consistently give environmental protection top priority. Achieving China's environmental goals, however, has been made difficult by China's economic growth. Part of this is due to the practice of environmental protection appearing in the form of an ideological 'campaign' or 'storm' that lacks effective economic measures. More recently, better enforcement of environmental laws and regulations has been achieved by adding environmental quality to the performance assessment metrics for leaders at all levels. To continue making advances, China needs to reinforce the economic and environmental assessments for pollution control projects and work harder to integrate economic measures into environmental protection. Nonetheless, China has a long way to go before economic growth and environmental protection are balanced.

  16. Experiment-Based Teaching in Advanced Control Engineering

    ERIC Educational Resources Information Center

    Precup, R.-E.; Preitl, S.; Radac, M.-B.; Petriu, E. M.; Dragos, C.-A.; Tar, J. K.

    2011-01-01

    This paper discusses an experiment-based approach to teaching an advanced control engineering syllabus involving controlled plant analysis and modeling, control structures and algorithms, real-time laboratory experiments, and their assessment. These experiments are structured around the representative case of the longitudinal slip control of an…

  17. Second Generation Advanced Reburning for High Efficiency NOx Control

    SciTech Connect

    Vladimir M. Zamansky; Peter M. Maly; Vitali V. Lissianski; Mark S. Sheldon; David Moyeda; Roy Payne

    2001-06-30

    This project develops a family of novel Second Generation Advanced Reburning (SGAR) NO{sub x} control technologies, which can achieve 95% NO{sub x} control in coal fired boilers at a significantly lower cost than Selective Catalytic Reduction (SCR). The conventional Advanced Reburning (AR) process integrates basic reburning and N-agent injection. The SGAR systems include six AR variants: (1) AR-Lean--injection of the N-agent and promoter along with overfire air; (2) AR-Rich--injection of N-agent and promoter into the reburning zone; (3) Multiple Injection Advanced Reburning (MIAR)--injection of N-agents and promoters both into the reburning zone and with overfire air; (4) AR-Lean + Promoted SNCR--injection of N-agents and promoters with overfire air and into the temperature zone at which Selective Non-Catalytic Reduction (SNCR) is effective; (5) AR-Rich + Promoted SNCR--injection of N-agents and promoters into the reburning zone and into the SNCR zone; and (6) Promoted Reburning + Promoted SNCR--basic or promoted reburning followed by basic or promoted SNCR process. The project was conducted in two phases over a five-year period. The work included a combination of analytical and experimental studies to confirm the process mechanisms, identify optimum process configurations, and develop a design methodology for full-scale applications. Phase I was conducted from October, 1995 to September, 1997 and included both analytical studies and tests in bench and pilot-scale test rigs. Phase I moved AR technology to Maturity Level III-Major Subsystems. Phase II is conducted over a 45 month period (October, 1997-June, 2001). Phase II included evaluation of alternative promoters, development of alternative reburning fuel and N-Agent jet mixing systems, and scale up. The goal of Phase II was to move the technology to Maturity Level I-Subscale Integrated System. Tests in combustion facility ranging in firing rate from 0.1 x 10{sup 6} to 10 x 10{sup 6} Btu/hr demonstrated the

  18. Pollution load calculation and control measures of nitrogen and phosphorus in Huangshi

    NASA Astrophysics Data System (ADS)

    Li, Haiyan; Wang, Qian; Shi, Youhui

    2011-02-01

    On the basis of the agricultural non-point source pollution data survey to Daye and Yangxin, the main pollution loads and main pollution factors is calculated through the relevant formulas. Some conclusions are drawn as follow: The emissions of Nitrogen and phosphorus pollutants from chemical fertilizers poultry and aquaculture are 6043.32t/a, 1044.81 t/a. The emissions in Yangxin (2511.88 t/a, 464.68 t/a) was higher than that in Daye (3531.44 t/a, 580.13 t/a). The Pollutants emissions and pollution load are characterized by Poultry> Chemical fertilizers > Aquaculture in Yangxin. But the features of Daye is aquaculture > poultry> synthetic fertilizer. Thought the comparison of the equivalent load, Nitrogen and phosphorus pollutants from aquaculture are identified as the main pollution factors. The results show that Phosphorus is the main controlling factor from Poultry. The emissions concentration of Nitrogen and phosphorus is above the requirements of Grade III on surface water(TN1.0mg/l, TP0.2mg/l). Appropriate control measures are put forward against main pollution sources and main pollution factors.

  19. Assessing and controlling the effect of aircraft on the environment: Pollution

    NASA Technical Reports Server (NTRS)

    Poppoff, I. G.; Grobman, J. S.

    1975-01-01

    The air pollution created by aircraft engines around airports and the global atmospheric problem of supersonic aircraft operating in the stratosphere are discussed. Methods for assessing the air pollution impact are proposed. The use of atmospheric models to determine the air pollution extent is described. Methods for controlling the emissions of aircraft engines are examined. Diagrams of the atmospheric composition resulting from exhaust gas emissions are developed.

  20. Indoor air pollution: Sources and control. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect

    Not Available

    1994-01-01

    The bibliography contains citations concerning indoor air pollution in residential, commercial, industrial, and institutional buildings. Indoor air quality assessment, health hazard evaluation, and contaminant identification and measurement are discussed. Indoor air pollution control methods and equipment are evaluated. Air quality analyses of energy efficient buildings are presented. Indoor air pollution from radon and asbestos are discussed in other bibliographies. (Contains 250 citations and includes a subject term index and title list.)

  1. Indoor air pollution: Sources and control. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect

    1998-02-01

    The bibliography contains citations concerning indoor air pollution in residential, commercial, industrial, and institutional buildings. Indoor air quality assessment, health hazard evaluation, and contaminant identification and measurement are discussed. Indoor air pollution control methods and equipment are evaluated. Air quality analyses of energy efficient buildings are presented. Indoor air pollution from radon and asbestos are discussed in other bibliographies. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  2. Indoor air pollution: Sources and control. (Latest citations from the NTIS Bibliographic database). NewSearch

    SciTech Connect

    Not Available

    1994-11-01

    The bibliography contains citations concerning indoor air pollution in residential, commercial, industrial, and institutional buildings. Indoor air quality assessment, health hazard evaluation, and contaminant identification and measurement are discussed. Indoor air pollution control methods and equipment are evaluated. Air quality analyses of energy efficient buildings are presented. Indoor air pollution from radon and asbestos are discussed in other bibliographies. (Contains 250 citations and includes a subject term index and title list.)

  3. Indoor air pollution: Sources and control. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect

    1996-12-01

    The bibliography contains citations concerning indoor air pollution in residential, commercial, industrial, and institutional buildings. Indoor air quality assessment, health hazard evaluation, and contaminant identification and measurement are discussed. Indoor air pollution control methods and equipment are evaluated. Air quality analyses of energy efficient buildings are presented. Indoor air pollution from radon and asbestos are discussed in other bibliographies.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  4. Indoor air pollution: Sources and control. (Latest citations from the NTIS bibliographic database). Published Search

    SciTech Connect

    1995-10-01

    The bibliography contains citations concerning indoor air pollution in residential, commercial, industrial, and institutional buildings. Indoor air quality assessment, health hazard evaluation, and contaminant identification and measurement are discussed. Indoor air pollution control methods and equipment are evaluated. Air quality analyses of energy efficient buildings are presented. Indoor air pollution from radon and asbestos are discussed in other bibliographies.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  5. Oil shale derived pollutant control materials and methods and apparatuses for producing and utilizing the same

    DOEpatents

    Boardman, Richard D.; Carrington, Robert A.

    2010-05-04

    Pollution control substances may be formed from the combustion of oil shale, which may produce a kerogen-based pyrolysis gas and shale sorbent, each of which may be used to reduce, absorb, or adsorb pollutants in pollution producing combustion processes, pyrolysis processes, or other reaction processes. Pyrolysis gases produced during the combustion or gasification of oil shale may also be used as a combustion gas or may be processed or otherwise refined to produce synthetic gases and fuels.

  6. Comparison of advanced distillation control methods. First annual report

    SciTech Connect

    Riggs, J.B.

    1996-11-01

    A detailed dynamic simulator of a propylene/propane (C{sub 3}) splitter, which was bench-marked against industrial data, has been used to compare dual composition control performance for a diagonal PI controller and several advanced controllers. The advanced controllers considered are dynamic matrix control (DMC), nonlinear process model based control, and artificial neutral networks. Each controller was tuned based upon setpoint changes in the overhead product composition using 50% changes in the impurity levels. Overall, there was not a great deal of difference in controller performance based upon the setpoint and disturbance tests. Periodic step changes in feed composition were also used to compare controller performance. In this case, oscillatory variations of the product composition were observed and the variabilities of the DC and nonlinear process model based controllers were substantially smaller than that of the PI controller. The sensitivity of each controller to the frequency of the periodic step changes in feed composition was also investigated.

  7. Smart Engines Via Advanced Model Based Controls

    SciTech Connect

    Allain, Marc

    2000-08-20

    A ''new'' process for developing control systems - Less engine testing - More robust control system - Shorter development cycle time - ''Smarter'' approach to engine control - On-board models describe engine behavior - Shorter, systematic calibration process - Customer and legislative requirements designed-in.

  8. Advanced control evaluation for structures (ACES) programs

    NASA Technical Reports Server (NTRS)

    Pearson, Jerome; Waites, Henry

    1988-01-01

    The ACES programs are a series of past, present, and future activities at the Marshall Space Flight Center (MSFC) Ground facility for Large Space Structure Control Verification (GF/LSSCV). The main objectives of the ACES programs are to implement control techniques on a series of complex dynamical systems, to determine the control/structure interaction for the control techniques, and to provide a national facility in which dynamics and control verification can be effected. The focus is on these objectives and how they are implemented under various engineering and economic constraints. Future plans that will be effected in upcoming ACES programs are considered.

  9. An advanced intelligent control system framework

    NASA Technical Reports Server (NTRS)

    Nemeth, ED; Anderson, Ronald R.; Maram, Jon; Norman, Arnie; Merrill, Walt

    1992-01-01

    A reusable rocket-engine intelligent control system (RREICS) framework was developed to a define a control framework for rocket-engine systems that reduces the required engine maintenance, extends the useful operating life, and maximizes the probability of mission success. The RREICS framework defines a controller that handles a rocket engine cluster as a single system rather than as a collection of individual engines. This enables the controller to alter individual engine operations in response to engine performance or integrity degradations while maintaining the propulsion subsystem external parameters at the levels required for mission success. A simplified model of a three engine cluster and the associated propulsion subsystem controller is also described.

  10. Advanced control strategies for fluidized bed dryers

    SciTech Connect

    Siettos, C.I.; Kiranoudis, C.T.; Bafas, G.V.

    1999-11-01

    Generating the best possible control strategy comprises a necessity for industrial processes, by virtue of product quality, cost reduction and design simplicity. Three different control approaches, namely an Input-Output linearizing, a fuzzy logic and a PID controller, are evaluated for the control of a fluidized bed dryer, a typical non-linear drying process of wide applicability. Based on several closed loop characteristics such as settling times, maximum overshoots and dynamic performance criteria such as IAE, ISE and ITAE, it is shown that the Input-Output linearizing and the fuzzy logic controller exhibit a better performance compared to the PID controller tuned optimally with respect to IAE, for a wide range of disturbances; yet, the relevant advantage of the fuzzy logic over the conventional nonlinear controller issues upon its design simplicity. Typical load rejection and set-point tracking examples are given to illustrate the effectiveness of the proposed approach.

  11. Comparison of advanced distillation control methods. First annual report

    SciTech Connect

    1996-11-01

    A detailed dynamic simulator of a propylene/propane (C3) splitter, which was bench-marked against industrial data, has been used to compare dual composition control performance for a diagonal PI controller and several advanced controllers. The advanced controllers considered are DMC, nonlinear process model based control, and articial neutral networks. Each controller was tuned based upon setpoint changes in the overhead product composition using 50% changes in the impurity levels. Overall, there was not a great deal of difference in controller performance based upon the setpoint and disturbance tests. Periodic step changes in feed composition were also used to compare controller performance. In this case, oscillatory variations of the product composition were observed and the variabilities of the DMC and nonlinear process model based controllers were substantially smaller than that of the PI controller. The sensitivity of each controller to the frequency of the periodic step changes in feed composition was also investigated.

  12. Study on control of micro-pollutants by BAC filtration.

    PubMed

    Zhang, Z H; Shao, L

    2008-01-01

    The objective of this research was to evaluate removal efficiency of micro-pollutants in a BAC filter that followed ozonation for long term operation. The experimental results showed that after continuous operation for one year BAC filter still maintained a removal of 15 approximately 20% for COD(Mn) and 20 approximately 30% of removal for UV(254). Correlative analysis based on lots of data found that empty bed contact time (EBCT) instead of flow rate could obviously impact on removal effect of micro-pollutants in BAC filter. And the optimal relationship between EBCT and removal effect of micro-pollutants for BAC filter was logarithm. On the other hand, long term running of BAC filter proved that there was a good removal of chloroform formation potential, but the removal of brominated trihalomethane formation potential decline with further bromization, even there appeared to be formation of bromoform in BAC filter. PMID:18725738

  13. Advanced rotorcraft control using parameter optimization

    NASA Technical Reports Server (NTRS)

    Vansteenwyk, Brett; Ly, Uy-Loi

    1991-01-01

    A reliable algorithm for the evaluation of a quadratic performance index and its gradients with respect to the controller design parameters is presented. The algorithm is part of a design algorithm for an optimal linear dynamic output feedback controller that minimizes a finite time quadratic performance index. The numerical scheme is particularly robust when it is applied to the control law synthesis for systems with densely packed modes and where there is a high likelihood of encountering degeneracies in the closed loop eigensystem. This approach through the use of a accurate Pade series approximation does not require the closed loop system matrix to be diagonalizable. The algorithm has been included in a control design package for optimal robust low order controllers. Usefulness of the proposed numerical algorithm has been demonstrated using numerous practical design cases where degeneracies occur frequently in the closed loop system under an arbitrary controller design initialization and during the numerical search.

  14. Rotorcraft flying qualities improvement using advanced control

    NASA Technical Reports Server (NTRS)

    Walker, D.; Postlethwaite, I.; Howitt, J.; Foster, N.

    1993-01-01

    We report on recent experience gained when a multivariable helicopter flight control law was tested on the Large Motion Simulator (LMS) at DRA Bedford. This was part of a study into the application of multivariable control theory to the design of full-authority flight control systems for high-performance helicopters. In this paper, we present some of the results that were obtained during the piloted simulation trial and from subsequent off-line simulation and analysis. The performance provided by the control law led to level 1 handling quality ratings for almost all of the mission task elements assessed, both during the real-time and off-line analysis.

  15. Project T.E.A.M. (Technical Education Advancement Modules). Advanced Statistical Process Control.

    ERIC Educational Resources Information Center

    Dunlap, Dale

    This instructional guide, one of a series developed by the Technical Education Advancement Modules (TEAM) project, is a 20-hour advanced statistical process control (SPC) and quality improvement course designed to develop the following competencies: (1) understanding quality systems; (2) knowing the process; (3) solving quality problems; and (4)…

  16. Advanced Combustion and Emission Control Technical Team Roadmap

    SciTech Connect

    2013-06-01

    The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

  17. Coastal nonpoint pollution control program: Program development and approval guidance

    SciTech Connect

    Not Available

    1993-01-01

    The document, developed by NOAA and EPA, contains guidance for states in developing and implementing their coastal nonpoint pollutant source programs. It describes the requirements that must be met, including: the geographic scope of the program; the pollutant sources to be addressed; the types of management measures used; the establishment of critical areas; technical assistance, public participation, and administrative coordination; and, the process for program submission and Federal approval. The document also contains the criteria by which NOAA and EPA will review the states' submissions.

  18. Portable air pollution control equipment for the control of toxic particulate emissions

    SciTech Connect

    Chaurushia, A.; Odabashian, S.; Busch, E.

    1997-12-31

    Chromium VI (Cr VI) has been identified by the environmental regulatory agencies as a potent carcinogen among eleven heavy metals. A threshold level of 0.0001 lb/year for Cr VI emissions has been established by the California Air Resources Board for reporting under Assembly Bill 2588. A need for an innovative control technology to reduce fugitive emissions of Cr VI was identified during the Air Toxic Emissions Reduction Program at Northrop Grumman Military Aircraft Systems Division (NGMASD). NGMASD operates an aircraft assembly facility in El Segundo, CA. Nearly all of the aircraft components are coated with a protective coating (primer) prior to assembly. The primer has Cr VI as a component for its excellent corrosion resistance property. The complex assembly process requires fasteners which also need primer coating. Therefore, NGMASD utilizes High Volume Low Pressure (HVLP) guns for the touch-up spray coating operations. During the touch-up spray coating operations, Cr VI particles are atomized and transferred to the aircraft surface. The South Coast Air Quality Management District (SCAQMD) has determined that the HVLP gun transfers 65% of the paint particles onto the substrate and the remaining 35% are emitted as an overspray if air pollution controls are not applied. NGMASD has developed the Portable Air Pollution Control Equipment (PAPCE) to capture and control the overspray in order to reduce fugitive Cr VI emissions from the touch-up spray coating operations. A source test was performed per SCAQMD guidelines and the final report has been approved by the SCAQMD.

  19. Model-free adaptive control of advanced power plants

    SciTech Connect

    Cheng, George Shu-Xing; Mulkey, Steven L.; Wang, Qiang

    2015-08-18

    A novel 3-Input-3-Output (3.times.3) Model-Free Adaptive (MFA) controller with a set of artificial neural networks as part of the controller is introduced. A 3.times.3 MFA control system using the inventive 3.times.3 MFA controller is described to control key process variables including Power, Steam Throttle Pressure, and Steam Temperature of boiler-turbine-generator (BTG) units in conventional and advanced power plants. Those advanced power plants may comprise Once-Through Supercritical (OTSC) Boilers, Circulating Fluidized-Bed (CFB) Boilers, and Once-Through Supercritical Circulating Fluidized-Bed (OTSC CFB) Boilers.

  20. 40 CFR 123.28 - Control of disposal of pollutants into wells.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 22 2014-07-01 2013-07-01 true Control of disposal of pollutants into wells. 123.28 Section 123.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER..., however, that CWA excludes certain types of well injections from the definition of “pollutant.” If...

  1. 40 CFR 123.28 - Control of disposal of pollutants into wells.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Control of disposal of pollutants into wells. 123.28 Section 123.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER..., however, that CWA excludes certain types of well injections from the definition of “pollutant.” If...

  2. 40 CFR 123.28 - Control of disposal of pollutants into wells.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 23 2012-07-01 2012-07-01 false Control of disposal of pollutants into wells. 123.28 Section 123.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER..., however, that CWA excludes certain types of well injections from the definition of “pollutant.” If...

  3. 40 CFR 123.28 - Control of disposal of pollutants into wells.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Control of disposal of pollutants into wells. 123.28 Section 123.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER..., however, that CWA excludes certain types of well injections from the definition of “pollutant.” If...

  4. 76 FR 75857 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-05

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... proposing to approve revisions to the Placer County Air Pollution Control District (PCAPCD) portion of the... local rules to regulate these emission sources under the Clean Air Act as amended in 1990 (CAA or...

  5. 77 FR 73322 - Revisions to the California State Implementation Plan, Monterey Bay Unified Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-10

    ...: EPA is taking direct final action to approve revisions to the Monterey Bay Unified Air Pollution... Part 52 Environmental protection, Air pollution control, Incorporation by reference, Intergovernmental... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Monterey Bay Unified...

  6. 78 FR 37176 - Revisions to the California State Implementation Plan, San Diego Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-20

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, San Diego Air Pollution... proposing to approve a revision to the San Diego Air Pollution Control District (SDAPCD) portion of the... sources under the Clean Air Act (CAA or the Act). DATES: Any comments on this proposal must arrive by...

  7. 78 FR 894 - Interim Final Determination To Stay Sanctions, Imperial County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-07

    ... AGENCY 40 CFR Part 52 Interim Final Determination To Stay Sanctions, Imperial County Air Pollution... of revisions to the Imperial County Air Pollution Control District (ICAPCD) portion of the California...- line instructions. 2. Email: steckel.andrew@epa.gov . 3. Mail or deliver: Andrew Steckel (Air-4),...

  8. 76 FR 67396 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-01

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... proposing to approve revisions to the Placer County Air Pollution Control District (PCAPCD) and Sacramento Metro Air Quality Management District (SMAQMD) portions of the California State Implementation Plan...

  9. 78 FR 6784 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-31

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... proposing to approve revisions to the Placer County Air Pollution Control District (PCAPCD) portion of the... approve local rules to regulate this emission source under the Clean Air Act (CAA or the Act). DATES:...

  10. 77 FR 67322 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-09

    ... AGENCY 40 CFR Part 52 Revisions to the California State Implementation Plan, Placer County Air Pollution... proposing to approve revisions to the Placer County Air Pollution Control District (PCAPCD) portion of the... FR 2643). III. Statutory and Executive Order Reviews Under the Clean Air Act, the Administrator...

  11. Processes, Procedures, and Methods to Control Pollution Resulting from Silvicultural Activities.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC. Office of Water Programs.

    This report presents brief documentation of silvicultural practices, both those now in use and those in stages of research and development. A majority of the text is concerned with the specific aspects of silvicultural activities which relate to nonpoint source pollution control methods. Analyzed are existing and near future pollution control…

  12. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  13. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 4 2011-10-01 2011-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  14. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 4 2012-10-01 2012-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  15. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 4 2014-10-01 2014-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  16. 45 CFR 2543.86 - Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 4 2013-10-01 2013-10-01 false Clean Air Act and the Federal Water Pollution... Water Pollution Control Act. Contracts and subgrants of amounts in excess of $100,000 shall contain a... regulations issued pursuant to the Clean Air Act (42 U.S.C. 7401 et seq.) and the Federal Water...

  17. Advanced dc-Traction-Motor Control System

    NASA Technical Reports Server (NTRS)

    Vittone, O.

    1985-01-01

    Motor-control concept for battery-powered vehicles includes stateof-the-art power-transistor switching and separate excitation of motor windings in traction and regenerative braking. Switching transistors and other components of power-conditioning subsystem operate under control of computer that coordinates traction, braking, and protective functions.

  18. Evaluating the effects of China's pollution controls on inter-annual trends and uncertainties of atmospheric mercury emissions

    NASA Astrophysics Data System (ADS)

    Zhao, Y.; Zhong, H.; Zhang, J.; Nielsen, C. P.

    2015-04-01

    China's anthropogenic emissions of atmospheric mercury (Hg) are effectively constrained by national air pollution control and energy efficiency policies. In this study, improved methods, based on available data from domestic field measurements, are developed to quantify the benefits of Hg abatement by various emission control measures. Those measures include increased use of (1) flue gas desulfurization (FGD) and selective catalyst reduction (SCR) systems in power generation; (2) precalciner kilns with fabric filters (FF) in cement production; (3) mechanized coking ovens with electrostatic precipitators (ESP) in iron and steel production; and (4) advanced production technologies in nonferrous metal smelting. Investigation reveals declining trends in emission factors for each of these sources, which together drive a much slower growth of total Hg emissions than the growth of China's energy consumption and economy, from 679 metric tons (t) in 2005 to 750 t in 2012. In particular, estimated emissions from the above-mentioned four source types declined 3% from 2005 to 2012, which can be attributed to expanded deployment of technologies with higher energy efficiencies and air pollutant removal rates. Emissions from other anthropogenic sources are estimated to increase by 22% during the period. The species shares of total Hg emissions have been stable in recent years, with mass fractions of around 55, 39, and 6% for gaseous elemental Hg (Hg0), reactive gaseous mercury (Hg2+), and particle-bound mercury (Hgp), respectively. The higher estimate of total Hg emissions than previous inventories is supported by limited simulation of atmospheric chemistry and transport. With improved implementation of emission controls and energy saving, a 23% reduction in annual Hg emissions from 2012 to 2030, to below 600 t, is expected at the most. While growth in Hg emissions has been gradually constrained, uncertainties quantified by Monte Carlo simulation for recent years have increased

  19. Evaluating the effects of China's pollution control on inter-annual trends and uncertainties of atmospheric mercury emissions

    NASA Astrophysics Data System (ADS)

    Zhao, Y.; Zhong, H.; Zhang, J.; Nielsen, C. P.

    2014-10-01

    China's atmospheric mercury (Hg) emissions of anthropogenic origin have been effectively restrained through the national policy of air pollution control. Improved methods based on available field measurements are developed to quantify the benefits of Hg abatement through various emission control measures. Those measures include increased use of flue gas desulfurization (FGD) and selective catalyst reduction (SCR) systems for power sector, precalciners with fabric filter (FF) for cement production, machinery coking with electrostatic precipitator (ESP) for iron and steel production, and advanced manufacturing technologies for nonferrous metal smelting. Declining trends in emissions factors for those sources are revealed, leading to a much slower growth of national total Hg emissions than that of energy and economy, from 679 in 2005 to 750 metric tons (t) in 2012. In particular, nearly half of emissions from the above-mentioned four types of sources are expected to be reduced in 2012, attributed to expansion of technologies with high energy efficiencies and air pollutant removal rates after 2005. The speciation of Hg emissions keeps stable for recent years, with the mass fractions of around 55, 39 and 6% for Hg0, Hg2+ and Hgp, respectively. The lower estimate of Hg emissions than previous inventories is supported by limited chemistry simulation work, but middle-to-long term observation on ambient Hg levels is further needed to justify the inter-annual trends of estimated Hg emissions. With improved implementation of emission controls and energy saving, 23% reduction in annual Hg emissions for the most optimistic case in 2030 is expected compared to 2012, with total emissions below 600 t. While Hg emissions are evaluated to be gradually constrained, increased uncertainties are quantified with Monte-Carlo simulation for recent years, particularly for power and certain industrial sources. The uncertainty of Hg emissions from coal-fired power plants, as an example

  20. Advanced Topics in Wet-Weather Discharge Control

    EPA Science Inventory

    This report discusses four related but generally independent wet-weather flow (WWF) topic areas, namely: i) opportunities for advanced practices in WWF control technology, particularly as it applies to sewered systems; ii) tradeoffs between storage facilities (tanks) and enlarged...

  1. Status report on the Advanced Light Source control system

    SciTech Connect

    Magyary, S.; Chin, M.; Fahmie, M.; Lancaster, H.; Molinari, P.; Robb, A.; Timossi, C.; Young, J.

    1991-11-11

    This paper is a status report on the ADVANCED LIGHT SOURCE (ALS) control system. The current status, performance data, and future plans will be discussed. Manpower, scheduling, and costs issues are addressed.

  2. Advanced control of a flexible spherical wrist

    NASA Astrophysics Data System (ADS)

    Gorgenyi, Louis Alexander

    1993-07-01

    A flexible spherical wrist, susceptible to nonlinear torsional vibrations, was developed which utilizes controllers to provide position control and vibration rejection. The issue of robust performance and stability for this robot wrist is examined while adhearing to practical implementation limits. System identification techniques are used to obtain linear models of the dynamic equations of motion. These models contain physical information such as friction and cable drag, and several different parametric forms are presented. Asymptotic stability of the wrist under proportional derivative control is proven using a linearized set of dynamical equations. Experimental results show only stability rather than asymptotic stability due to friction and unmodeled dynamics. In addition, poor robustness of this control methodology is demonstrated when the orientation and payload are varied. One- and two-parameter Hardy space controllers are designed to address the robustness and implementation issues. Variations in wrist orientation and payload are modeled as multiplicative uncertainties. Simulation and experimental results are presented and compared to those of a tracking controller. The Hardy space controllers are shown to have superior robustness properties but poorer performance.

  3. Residuals Charges for Pollution Control: A Policy Evaluation

    ERIC Educational Resources Information Center

    Freeman, A. Myrick, III; Haveman, Robert H.

    1972-01-01

    Contrasts the effects of a policy of regulation of pollutant discharge by enforcement of a permit system with the likely consequences of a policy of charging for effluents, thus increasing the cost of discharge. The charge for residuals is favored, and it is suggested that trials of the system be conducted, perhaps with a federal tax on emission…

  4. The Economist's Approach to Pollution and Its Control

    ERIC Educational Resources Information Center

    Solow, Robert M.

    1971-01-01

    Shows that excess pollution arises because the waste disposal capacity of the environment is provided free of charge. Proposes a tax on materials removed from the environment, with refunds varying with the method of disposal: harmless methods obtaining full refund, most harmful disposal attracting no refund. Tax to be based on social cost of most…

  5. Identification and Control of Pollution from Salt Water Intrusion.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC. Office of Water Programs.

    This document contains informational guidelines for identifying and evaluating the nature and extent of pollution from salt water intrusion. The intent of these guidelines is to provide a basic framework for assessing salt water intrusion problems and their relationship to the total hydrologic system, and to provide assistance in developing…

  6. PULVERIZED COAL COMBUSTION: POLLUTANT FORMATION AND CONTROL, 1970-1980

    EPA Science Inventory

    The report documents the support role of EPA's Air and Energy Engineering Research Laboratory in the major research effort directed by EPA in the l970s to understand pollutant formation during pulverized coal combustion (PCC). Understanding the conversion of fuel nitrogen to nit...

  7. Environmental Pollution Control: Two Views from the General Population

    ERIC Educational Resources Information Center

    Althoff, Phillip; Greig, William H.

    1977-01-01

    Citizens exhibitied concern about pollution, a low level of trust in governmental and industrial efforts, and a low level of dedication to environmental protection. Demands to clean up the environment came from one segment of the population while demands to solve the energy crisis came from other segments. (AJ)

  8. Electrical Production and Pollution Control. Environmental Education Curriculum.

    ERIC Educational Resources Information Center

    Topeka Public Schools, KS.

    Citizen use of our nation's industrial products has led to increased pollution problems and demand for diminishing energy reserves. In an attempt to encourage intelligent cooperation among science, industry, government and all citizens, this unit was developed to introduce secondary science students to the many facets of the electrical production…

  9. Attitude Control Subsystem for the Advanced Communications Technology Satellite

    NASA Technical Reports Server (NTRS)

    Hewston, Alan W.; Mitchell, Kent A.; Sawicki, Jerzy T.

    1996-01-01

    This paper provides an overview of the on-orbit operation of the Attitude Control Subsystem (ACS) for the Advanced Communications Technology Satellite (ACTS). The three ACTS control axes are defined, including the means for sensing attitude and determining the pointing errors. The desired pointing requirements for various modes of control as well as the disturbance torques that oppose the control are identified. Finally, the hardware actuators and control loops utilized to reduce the attitude error are described.

  10. Advanced gel propulsion controls for kill vehicles

    NASA Astrophysics Data System (ADS)

    Yasuhara, W. K.; Olson, A.; Finato, S.

    1993-06-01

    A gel propulsion control concept for tactical applications is reviewed, and the status of the individual component technologies currently under development at the Aerojet Propulsion Division is discussed. It is concluded that a gel propellant Divert and Attitude Control Subsystem (DACS) provides a safe, insensitive munitions compliant alternative to current liquid Theater Missile Defense (TMD) DACS approaches. The gel kill vehicle (KV) control system packages a total impulse typical of a tactical weapon interceptor for the ground- or sea-based TMD systems. High density packaging makes it possible to increase firepower and to eliminate long-term high pressure gas storage associated with bipropellant systems. The integrated control subsystem technologies encompass solid propellant gas generators, insulated composite overwrapped propellant tanks, lightweight endoatmospheric thrusters, and insensitive munition gel propellants, which meet the requirements of a deployable, operationally safe KV.

  11. Advancing infection control in dental care settings

    PubMed Central

    Cleveland, Jennifer L.; Bonito, Arthur J.; Corley, Tammy J.; Foster, Misty; Barker, Laurie; Brown, G. Gordon; Lenfestey, Nancy; Lux, Linda

    2015-01-01

    Background and Overview The authors set out to identify factors associated with implementation by U.S. dentists of four practices first recommended in the Centers for Disease Control and Prevention’s Guidelines for Infection Control in Dental Health-Care Settings—2003. Methods In 2008, the authors surveyed a stratified random sample of 6,825 U.S. dentists. The response rate was 49 percent. The authors gathered data regarding dentists’ demographic and practice characteristics, attitudes toward infection control, sources of instruction regarding the guidelines and knowledge about the need to use sterile water for surgical procedures. Then they assessed the impact of those factors on the implementation of four recommendations: having an infection control coordinator, maintaining dental unit water quality, documenting percutaneous injuries and using safer medical devices, such as safer syringes and scalpels. The authors conducted bivariate analyses and proportional odds modeling. Results Responding dentists in 34 percent of practices had implemented none or one of the four recommendations, 40 percent had implemented two of the recommendations and 26 percent had implemented three or four of the recommendations. The likelihood of implementation was higher among dentists who acknowledged the importance of infection control, had practiced dentistry for less than 30 years, had received more continuing dental education credits in infection control, correctly identified more surgical procedures that require the use of sterile water, worked in larger practices and had at least three sources of instruction regarding the guidelines. Dentists with practices in the South Atlantic, Middle Atlantic or East South Central U.S. Census divisions were less likely to have complied. Conclusions Implementation of the four recommendations varied among U.S. dentists. Strategies targeted at raising awareness of the importance of infection control, increasing continuing education

  12. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control...

  13. 40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control...

  14. 40 CFR 60.2706 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air pollution control device inspection? 60.2706 Section 60.2706 Protection of Environment... Requirements § 60.2706 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days after installation of...

  15. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control...

  16. 40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control...

  17. 40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control...

  18. 40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... Compliance Requirements § 60.2141 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days...

  19. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control...

  20. 40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment... Requirements § 60.2716 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution control...

  1. 40 CFR 62.14441 - When must I inspect my HMIWI equipment and air pollution control devices?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... and air pollution control devices? 62.14441 Section 62.14441 Protection of Environment ENVIRONMENTAL... my HMIWI equipment and air pollution control devices? (a) You must inspect your large, medium, small... inspect the air pollution control devices on your large, medium, small or small rural HMIWI by May...

  2. 40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control...

  3. 40 CFR 60.2716 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... air pollution control device inspection? 60.2716 Section 60.2716 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY... annual air pollution control device inspection), you must complete the air pollution control...

  4. 40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control...

  5. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control...

  6. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control...

  7. 40 CFR 60.5215 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution control device used to comply with the emission limits, according to § 60.5220(c), no later than 12 months following the previous annual air pollution control...

  8. 40 CFR 60.2141 - By what date must I conduct the initial air pollution control device inspection?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... air pollution control device inspection? 60.2141 Section 60.2141 Protection of Environment... Compliance Requirements § 60.2141 By what date must I conduct the initial air pollution control device inspection? (a) The initial air pollution control device inspection must be conducted within 60 days...

  9. 40 CFR 62.14441 - When must I inspect my HMIWI equipment and air pollution control devices?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... and air pollution control devices? 62.14441 Section 62.14441 Protection of Environment ENVIRONMENTAL... my HMIWI equipment and air pollution control devices? (a) You must inspect your large, medium, small... inspect the air pollution control devices on your large, medium, small or small rural HMIWI by May...

  10. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT... Pollution Control Act. Pursuant to regulations of the Environmental Protection Agency (40 CFR part 15) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act...

  11. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT... Pollution Control Act. Pursuant to regulations of the Environmental Protection Agency (40 CFR part 15) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act...

  12. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT... Pollution Control Act. Pursuant to regulations of the Environmental Protection Agency (40 CFR part 15) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act...

  13. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT... Pollution Control Act. Pursuant to regulations of the Environmental Protection Agency (40 CFR part 15) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act...

  14. 23 CFR 633.211 - Implementation of the Clean Air Act and the Federal Water Pollution Control Act.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Water Pollution Control Act. 633.211 Section 633.211 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT... Pollution Control Act. Pursuant to regulations of the Environmental Protection Agency (40 CFR part 15) implementing requirements with respect to the Clean Air Act and the Federal Water Pollution Control Act...

  15. Control of Smart Building Using Advanced SCADA

    NASA Astrophysics Data System (ADS)

    Samuel, Vivin Thomas

    For complete control of the building, a proper SCADA implementation and the optimization strategy has to be build. For better communication and efficiency a proper channel between the Communication protocol and SCADA has to be designed. This paper concentrate mainly between the communication protocol, and the SCADA implementation, for a better optimization and energy savings is derived to large scale industrial buildings. The communication channel used in order to completely control the building remotely from a distant place. For an efficient result we consider the temperature values and the power ratings of the equipment so that while controlling the equipment, we are setting a threshold values for FDD technique implementation. Building management system became a vital source for any building to maintain it and for safety purpose. Smart buildings, refers to various distinct features, where the complete automation system, office building controls, data center controls. ELC's are used to communicate the load values of the building to the remote server from a far location with the help of an Ethernet communication channel. Based on the demand fluctuation and the peak voltage, the loads operate differently increasing the consumption rate thus results in the increase in the annual consumption bill. In modern days, saving energy and reducing the consumption bill is most essential for any building for a better and long operation. The equipment - monitored regularly and optimization strategy is implemented for cost reduction automation system. Thus results in the reduction of annual cost reduction and load lifetime increase.

  16. Advanced mobile networking, sensing, and controls.

    SciTech Connect

    Feddema, John Todd; Kilman, Dominique Marie; Byrne, Raymond Harry; Young, Joseph G.; Lewis, Christopher L.; Van Leeuwen, Brian P.; Robinett, Rush D. III; Harrington, John J.

    2005-03-01

    This report describes an integrated approach for designing communication, sensing, and control systems for mobile distributed systems. Graph theoretic methods are used to analyze the input/output reachability and structural controllability and observability of a decentralized system. Embedded in each network node, this analysis will automatically reconfigure an ad hoc communication network for the sensing and control task at hand. The graph analysis can also be used to create the optimal communication flow control based upon the spatial distribution of the network nodes. Edge coloring algorithms tell us that the minimum number of time slots in a planar network is equal to either the maximum number of adjacent nodes (or degree) of the undirected graph plus some small number. Therefore, the more spread out that the nodes are, the fewer number of time slots are needed for communication, and the smaller the latency between nodes. In a coupled system, this results in a more responsive sensor network and control system. Network protocols are developed to propagate this information, and distributed algorithms are developed to automatically adjust the number of time slots available for communication. These protocols and algorithms must be extremely efficient and only updated as network nodes move. In addition, queuing theory is used to analyze the delay characteristics of Carrier Sense Multiple Access (CSMA) networks. This report documents the analysis, simulation, and implementation of these algorithms performed under this Laboratory Directed Research and Development (LDRD) effort.

  17. Field Operations and Enforcement Manual for Air Pollution Control. Volume II: Control Technology and General Source Inspection.

    ERIC Educational Resources Information Center

    Weisburd, Melvin I.

    The Field Operations and Enforcement Manual for Air Pollution Control, Volume II, explains in detail the following: technology of source control, modification of operations, particulate control equipment, sulfur dioxide removal systems for power plants, and control equipment for gases and vapors; inspection procedures for general sources, fuel…

  18. 75 FR 11878 - California State Motor Vehicle Pollution Control Standards; Amendments to the California Zero...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-12

    ... AGENCY California State Motor Vehicle Pollution Control Standards; Amendments to the California Zero Emission Vehicle (ZEV) Regulation; Waiver Request; Opportunity for Public Hearing AGENCY: Environmental... related to zero emission vehicles (ZEVs) in California. By letter dated September 17, 2009, CARB...

  19. [Identification of the prior regions for agricultural and rural pollution control in Changshu].

    PubMed

    Duan, Hua-ping; Sun, Qing-fang; Wang, Liang; Zhu, Lin; Feng, Jin-fei; Bian, Xin-min

    2010-04-01

    The characteristics such as wide area, dispersion and randomness of agricultural and rural pollution make it difficult to seize the key to pollution control in rural areas. On the scale of township, using inventory analysis, accounting for emissions and emission intensity of the chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) in Changshu, Jiangsu Province, which exists in a total of 4 classes and 6 kinds of agricultural and rural sources such as farmland cultivation (chemical fertilizer application and crop straw abandoned), animal breeding, aquaculture, rural life (domestic sewage and human waste, solid waste), using cluster analysis, identify the prior regions and the prior pollution sources for agricultural and rural pollution control by the sensitivity evaluation, and make agricultural and rural pollution control and management measures more focused. It shows that: in 2007, COD, TN and TP emissions of agricultural and rural pollution sources were 5496.07, 4161.03, and 647.54 t x a(-1), and the emission intensity of COD, TN and TP was 48.84, 36.98, and 5.75 kg x hm(-2). The main pollution source of COD was rural life and aquaculture, and the contribution rate was more than 75%; the main pollution source of TN and TP was agricultural cultivation and aquaculture, and the contribution rate was more than 80%. The sensitivity evaluation identified that the town of Guli and Shajiabang were the prior regions for agricultural and rural pollution control in Changshu; farmland cultivation and aquaculture were the prior pollution sources in the two areas.

  20. Human factors survey of advanced instrumentation and controls

    SciTech Connect

    Carter, R.J.

    1989-01-01

    A survey oriented towards identifying the human factors issues in regard to the use of advanced instrumentation and controls (I C) in the nuclear industry was conducted. A number of United States (US) and Canadian nuclear vendors and utilities were participants in the survey. Human factors items, subsumed under the categories of computer-generated displays (CGD), controls, organizational support, training, and related topics, were discussed. The survey found the industry to be concerned about the human factors issues related to the implementation of advanced I C. Fifteen potential human factors problems were identified. They include: the need for an advanced I C guideline equivalent to NUREG-0700; a role change in the control room from operator to supervisor; information overload; adequacy of existing training technology for advanced I C; and operator acceptance and trust. 11 refs., 1 tab.

  1. Modern advances in sustainable tick control

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Ticks are the vector of the many different organisms responsible for both animal and human diseases. Understanding the progress we have made and new directions in tick control is critical to the sustainability of human and animal health. The integration of vaccines, acaricides, and new acaricide ap...

  2. Increasingly intolerable boundaries: future control of environmental pollution.

    PubMed

    Scanlon, J

    2001-09-14

    In recent years, there have been a number of toxic accidents on the sea and on land which have caused pollution down current, down wind and down stream. Four were dramatic and these four have led to substantial changes in the way we deal with risk to the environment. There have also been increasing concerns about a less spectacular but equally concerning problem, acid rain, though attempts to deal with this problem have been less successful. Perhaps the drama was lacking. In all these cases, unfortunately, the less developed countries can ill afford the costs of prevention and this means they are often the home of environmentally unfriendly development. While the current approaches to such problems will continue, it is likely that the countries on the receiving end of such pollution, especially if they have economic and military power, will seek more forceful solutions. One outcome may be a UN-sponsored environmental police force.

  3. Policy instruments for pollution control in developing countries.

    PubMed

    Eskeland, G S; Jimenez, E

    1992-07-01

    Economic development in developing countries must be accomplished in a manner that does not harm the environment with pollution. Pollution harms human health and productivity. Thus appropriate strategies must be developed that promote growth, reduce poverty, and protect the environment. A review of the current literature is performed with attention paid to cost-effective interventions i.e., comparisons of regulatory and fiscal instruments that can reduce pollution. Both direct instruments (like effluent charges, tradable permits, deposit refund systems, emission regulations and regulatory agency funding for purification, cleanup, waste disposal, and enforcement) and indirect instruments (like input/output taxes and subsidies, substitution subsidies, abatement inputs, regulation of equipment and processes, and development of clean technologies) are examined. Examples are used to show how indirect instruments can be successful when monitoring and enforcement is too costly. A careful examination of distributive concerns illustrate how the effect on the poor may need particular consideration and how groups with vested interests can help evaluate the probable success of such interventions. PMID:12317607

  4. Elements of an advanced integrated operator control station

    SciTech Connect

    Clarke, M.M.; Kreifeldt, J.G.

    1984-01-01

    One of the critical determinants of peformance for any remotely operated maintenance system is the compatibility achieved between elements of the man/machine interface (e.g., master manipulator controller, controls, displays, etc.) and the human operator. In the Remote Control Engineering task of the Consolidated Fuel Reprocessing Program, considerable attention has been devoted to optimizing the man/machine interface of the operator control station. This system must be considered an integral element of the overall maintenance work system which includes transporters, manipulators, remote viewing, and other parts. The control station must reflect the integration of the operator team, control/display panels, manipulator master controllers, and remote viewing monitors. Human factors principles and experimentation have been used in the development of an advanced integrated operator control station designed for the advance servomanipulator. Key features of this next-generation design are summarized in this presentation. 7 references, 4 figures.

  5. Elements of an advanced integrated operator control station

    SciTech Connect

    Clarke, M.M.; Kreifeldt, J.G.

    1984-01-01

    One of the critical determinants of performance for any remotely operated maintenance system is the compatibility achieved between elements of the man/machine interface (e.g., master manipulator controller, controls, displays) and the human operator. In the remote control engineering task of the Consolidated Fuel Reprocessing Program, considerable attention has been devoted to optimizing the man/machine interface of the operator control station. This system must be considered an integral element of the overall maintenance work system which includes transporters, manipulators, remote viewing, and other parts. The control station must reflect the integration of the operator team, control/display panels, manipulator master controllers, and remote viewing monitors. Human factors principles and experimentation have been used in the development of an advanced integrated operator control station designed for the advance servomanipulator. Key features of this next-generation design are summarized in this presentation. 7 references, 4 figures.

  6. Fate of hydrocarbon pollutants in source and non-source control sustainable drainage systems.

    PubMed

    Roinas, Georgios; Mant, Cath; Williams, John B

    2014-01-01

    Sustainable drainage (SuDs) is an established method for managing runoff from developments, and source control is part of accepted design philosophy. However, there are limited studies into the contribution source control makes to pollutant removal, especially for roads. This study examines organic pollutants, total petroleum hydrocarbons (TPH) and polycyclic aromatic hydrocarbons (PAHs), in paired source and non-source control full-scale SuDs systems. Sites were selected to cover local roads, trunk roads and housing developments, with a range of SuDs, including porous asphalt, swales, detention basins and ponds. Soil and water samples were taken bi-monthly over 12 months to assess pollutant loads. Results show first flush patterns in storm events for solids, but not for TPH. The patterns of removal for specific PAHs were also different, reflecting varying physico-chemical properties. The potential of trunk roads for pollution was illustrated by peak runoff for TPH of > 17,000 μg/l. Overall there was no significant difference between pollutant loads from source and non-source control systems, but the dynamic nature of runoff means that longer-term data are required. The outcomes of this project will increase understanding of organic pollutants behaviour in SuDs. This will provide design guidance about the most appropriate systems for treating these pollutants.

  7. Fate of hydrocarbon pollutants in source and non-source control sustainable drainage systems.

    PubMed

    Roinas, Georgios; Mant, Cath; Williams, John B

    2014-01-01

    Sustainable drainage (SuDs) is an established method for managing runoff from developments, and source control is part of accepted design philosophy. However, there are limited studies into the contribution source control makes to pollutant removal, especially for roads. This study examines organic pollutants, total petroleum hydrocarbons (TPH) and polycyclic aromatic hydrocarbons (PAHs), in paired source and non-source control full-scale SuDs systems. Sites were selected to cover local roads, trunk roads and housing developments, with a range of SuDs, including porous asphalt, swales, detention basins and ponds. Soil and water samples were taken bi-monthly over 12 months to assess pollutant loads. Results show first flush patterns in storm events for solids, but not for TPH. The patterns of removal for specific PAHs were also different, reflecting varying physico-chemical properties. The potential of trunk roads for pollution was illustrated by peak runoff for TPH of > 17,000 μg/l. Overall there was no significant difference between pollutant loads from source and non-source control systems, but the dynamic nature of runoff means that longer-term data are required. The outcomes of this project will increase understanding of organic pollutants behaviour in SuDs. This will provide design guidance about the most appropriate systems for treating these pollutants. PMID:24569267

  8. Looking at pollution control in a new light: Photochemistry for a cleaner environment

    SciTech Connect

    1995-09-01

    This phamphet, from the National Renewable Energy Laboratory and Sandia National Laboratory, describes a major new development in the field of photochemistry. The NREL/Sandia team has developed a pollution control technique - photocatalytic oxidation (PCO) that uses the energy in light to destroy environmental contaminants. Applicable as both a waste clean-up and a pollution control technique, PCP could help thousands of businesses comply with environmental regulations.

  9. Advanced treatment of refractory organic pollutants in petrochemical industrial wastewater by bioactive enhanced ponds and wetland system.

    PubMed

    Liu, Shuo; Ma, Qiusha; Wang, Baozhen; Wang, Jifu; Zhang, Ying

    2014-05-01

    A large-scale combined ponds-wetland system was applied for advanced treatment of refractory pollutants in petrochemical industrial wastewater. The system was designed to enhance bioactivity and biological diversity, which consisted of anaerobic ponds (APs), facultative ponds (FPs), aerobic pond and wetland. The refractory pollutants in the petrochemical wastewater to be treated were identified as alkanes, chloroalkanes, aromatic hydrocarbons, and olefins, which were significantly degraded and transformed along with the influent flowing through the enhanced bioactive ponds-wetland system. 8 years of recent operational data revealed that the average removal rate of stable chemical oxygen demand (COD) was 42.7 % and that influent COD varied from 92.3 to 195.6 mg/L. Final effluent COD could reach 65.8 mg/L (average). COD removal rates were high in the APs and FPs and accounted for 75 % of the total amount removed. This result indicated that the APs and FPs degraded refractory pollutants through the facilitation of bacteria growth. The changes in the community structures of major microbes were assessed by 16SrDNA-denaturing gradient gel electrophoresis. The same analysis was used to identify the main bacterial function for the removal of refractory pollutants in the APs and FPs. The APs and FPs displayed similar microbial diversities, and some of the identified bacteria degraded and removed refractory pollutants. The overall results proved the applicability, stability, and high efficiency of the ponds-wetland system with enhanced bioactivity in the advanced removal of refractory pollutants from petrochemical industrial wastewater.

  10. Advanced motor and motor control development

    NASA Astrophysics Data System (ADS)

    Wuertz, Kenneth L.; Beauchamp, Edward D.

    1988-08-01

    The capability of operating a high speed permanent magnet brushless dc motor with electronic controller over a wide load and speed range was demonstrated. A centrifugal pump was used as the loading mechanism and hydraulic fluid was pumped in simulation of an aircraft engine fuel pump requirement. A motor speed of 45,000 rpm was reached and a maximum output of 68.5 hp was demonstrated. The response of the system to step commands for speed change was established. Reduction of size and weight of electronic control was established as a primary future goal. The program system concept with minor rotating machine improvements is viable for high speed drive applications up to 100-hp level.

  11. Advanced concepts for controlling energy surety microgrids.

    SciTech Connect

    Menicucci, David F.; Ortiz-Moyet, Juan

    2011-05-01

    Today, researchers, engineers, and policy makers are seeking ways to meet the world's growing demand for energy while addressing critical issues such as energy security, reliability, and sustainability. Many believe that distributed generators operating within a microgrid have the potential to address most of these issues. Sandia National Laboratories has developed a concept called energy surety in which five of these 'surety elements' are simultaneously considered: energy security, reliability, sustainability, safety, and cost-effectiveness. The surety methodology leads to a new microgrid design that we call an energy surety microgrid (ESM). This paper discusses the unique control requirement needed to produce a microgrid system that has high levels of surety, describes the control system from the most fundamental level through a real-world example, and discusses our ideas and concepts for a complete system.

  12. Advanced concepts in accelerator timing control

    SciTech Connect

    Frankel, R.; Salwen, C.

    1988-01-01

    The control system for the Booster accelerator presently under construction at BNL includes a timing section with serial high speed coded data distribution, computer based encoders for both real time and field driven clocks and a method of easily tracking the performance and reliability of these timing streams. We have developed a simple method for the generation of timing which operates to produce pulses which may be repeated as desired with minimal latency.

  13. Advanced CIDI Emission Control System Development

    SciTech Connect

    Lambert, Christine

    2006-05-31

    Ford Motor Company, with ExxonMobil and FEV, participated in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to develop an innovative emission control system for light-duty diesel vehicles. The focus on diesel engine emissions was a direct result of the improved volumetric fuel economy (up to 50%) and lower CO2 emissions (up to 25%) over comparable gasoline engines shown in Europe. Selective Catalytic Reduction (SCR) with aqueous urea as the NOx reductant and a Catalyzed Diesel Particulate Filter (CDPF) were chosen as the primary emission control system components. The program expected to demonstrate more than 90% durable reduction in particulate matter (PM) and NOx emissions on a light-duty truck application, based on the FTP-75 drive cycle. Very low sulfur diesel fuel (<15 ppm-wt) enabled lower PM emissions, reduced fuel economy penalty due to the emission control system and improved long-term system durability. Significant progress was made toward a durable system to meet Tier 2 Bin 5 emission standards on a 6000 lbs light-duty truck. A 40% reduction in engine-out NOx emissions was achieved with a mid-size prototype diesel engine through engine recalibration and increased exhaust gas recirculation. Use of a rapid warm-up strategy and urea SCR provided over 90% further NOx reduction while the CDPF reduced tailpipe PM to gasoline vehicle levels. Development work was conducted to separately improve urea SCR and CDPF system durability, as well as improved oxidation catalyst function. Exhaust gas NOx and ammonia sensors were also developed further. While the final emission control system did not meet Tier 2 Bin 5 NOx after 120k mi of aging on the dynamometer, it did meet the standards for HC, NMOG, and PM, and an improved SCR catalyst was shown to have potential to meet the NOx standard, assuming the DOC durability could be improved further. Models of DOC and SCR function were developed to guide the study of several key design

  14. Integrated Assessment of Air Pollution Control Measures for Megacities

    NASA Astrophysics Data System (ADS)

    Friedrich, R.; Theloke, J.; Denier-van-der-Gon, H.; Kugler, U.; Kampffmeyer, T.; Roos, J.; Torras, S.

    2012-04-01

    Air pollution in large cities is still a matter of concern. Especially the concentration of fine particles (PM10 and PM2.5) is largest in large cities leading to severe health impacts. Furthermore the PM10 thresholds of the EU Air Quality Directive are frequently exceeded. Thus the question arises, whether the initiated policies and measures for mitigating air pollution are sufficient to meet the air quality targets and - if not - which efficient further pollution mitigation measures exist. These questions have been addressed in the EU research project MEGAPOLI for the four European megacities respectively agglomerations London, Paris, Rhine-Ruhr area and Po valley. Firstly, a reference scenario of future activities and emissions has been compiled for the megacities for the years 2020, 2030 and 2050 for all relevant air pollutants (CO, NH3, NMVOC, NOx, PM10, PM2.5 and SO2) and greenhouse gases (CO2, CH4 and N2O). The reference scenario takes into account as well population changes as technical progress and economic growth. As pollution flowing in from outside the city is about as important as pollution caused by emissions in the city, the analysis covers the whole of Europe and not only the city area. Emissions are then transformed into concentrations using atmospheric models. The higher concentrations in cities were estimated with a newly developed 'urban increment' model. Results show, that in the megacities the limits of the Air Quality Directive (2008/50/EC) will be exceeded. Thus additional efforts are necessary to reduce emissions further. Thus, a number of further measures (not implemented in current legislation) were selected and assessed. These included mitigation options for road transport, other mobile sources, large combustion plants, small and medium combustion plants and industry. For each measure and in addition for various bundles of measures a cost-benefit analysis has been carried out. Benefits (avoided health risks and climate change risks) have

  15. Manpower Requirements for Pollution Control and Water Resources in Indiana and a Related Pollution Control Technology Curriculum. Manpower Report 69-1.

    ERIC Educational Resources Information Center

    Purdue Univ., Lafayette, IN. Office of Manpower Studies.

    The purpose of this study was to identify the trained manpower needed to cope with Indiana's mounting problems in air and water pollution control, liquid and solid waste disposal, and water supply and resources. This report contains data concerning the present employment, current job opportunities, and projected manpower needs for related…

  16. Advanced Strategies for Outdoor LED Lighting Applications and Technologies to Curtail Regional Light Pollution Effects

    NASA Astrophysics Data System (ADS)

    Monrad, Christian Karl; Benya, James R.

    2015-08-01

    LED lighting systems for outdoor lighting applications continue to evolve as do strategies to mitigate related effects upon regional astronomical and ecological assets. The improving availability and relative lumen-per-watt efficiencies of blue-suppressed low correlated color temperature emitters, narrow band amber, phosphor converted amber, and various combinations of broadband emitters and sub-550NM and sub-500NM filters allow for a wide palette of choices to be assessed to suit site-specific and task-specific lighting needs. In addition to static spectral content options, readily available luminaire designs also include precise geometric beam shape selections and adaptive controls to include dimming, dynamic spectral shifting, motion detection, and dynamic beam shaping to minimize total environmental lumen emissions throughout the course of the nighttime hours.Regional and international light pollution mitigation regulations will also be briefly addressed in the context of luminaire shielding and spectral content control efforts to better protect human quality of life issues as well as astronomical and ecological interests.The presentation will include numerous spectral content graphs for various luminaire options as well as project-specific case studies to document comparisons of legacy lighting systems versus high-performance LED systems with regard to total lumen emissions, skyglow contributions, energy efficiency, and end-user satisfaction with the installed LED lighting systems. Physical samples of various luminaires will also be available for hands-on assessments.

  17. Selected advanced aerodynamic and active control concepts development

    NASA Technical Reports Server (NTRS)

    1980-01-01

    A summary is presented of results obtained during analysis, design and test activities on six selected technical tasks directed at exploratory improvement of fuel efficiency for new and derivative transports. The work included investigations into the potential offered by natural laminar flow, improved surface coatings and advanced high lift concepts. Similar investigations covering optimum low-energy flight path control, integrated application of active controls and evaluation of primary flight control systems reliability and maintenance are also summarized. Recommendations are included for future work needed to exploit potential advancements.

  18. Cylinder Pressure-Based Spark Advance Control for SI Engines

    NASA Astrophysics Data System (ADS)

    Park, Seungbum; Yoon, Paljoo; Sunwoo, Myoungho

    The introduction of inexpensive cylinder pressure sensors provides new opportunities for precise engine control. This paper presents a spark advance control strategy based upon cylinder pressure in spark ignition engines. It is well known that the location of peak pressure(LPP) reflects combustion phasing and can be used for controlling the spark advance. The well-known problems of the LPP-based spark advance control method are that many samples of data are required and there is loss of combustion phasing detection capability due to hook-back at late burn conditions. To solve these problems, a multi-layer feedforward neural network is employed. The LPP and hook-back are estimated, using the neural network, which needs only five output voltage samples from the pressure sensor. The neural network plays an important role in mitigating the A/D conversion load of an electronic engine controller by increasing the sampling interval from 1° crank angle (CA) to 20° CA. A proposed control algorithm does not need a sensor calibration and pegging (bias calculation) procedure because the neural network estimates the LPP from the raw sensor output voltage. The estimated LPP can be regarded as a good index for combustion phasing, and can also be used as an MBT control parameter. The feasibility of this methodology is closely examined through steady and transient engine operations to control individual cylinder spark advances. The experimental results have revealed a favorable agreement of optimal combustion phasing in each cylinder.

  19. Advanced Integrated Power and Attitude Control System (IPACS) study

    NASA Technical Reports Server (NTRS)

    Oglevie, R. E.; Eisenhaure, D. B.

    1985-01-01

    Integrated Power and Attitude Control System (IPACS) studies performed over a decade ago established the feasibility of simultaneously satisfying the demands of energy storage and attitude control through the use of rotating flywheels. It was demonstrated that, for a wide spectrum of applications, such a system possessed many advantages over contemporary energy storage and attitude control approaches. More recent technology advances in composite material rotors, magnetic suspension systems, and power control electronics have triggered new optimism regarding the applicability and merits of this concept. This study is undertaken to define an advanced IPACS and to evaluate its merits for a space station application. System and component designs are developed to establish the performance of this concept and system trade studies conducted to examine the viability of this approach relative to conventional candidate systems. It is clearly demonstrated that an advanced IPACS concept is not only feasible, but also offers substantial savings in mass and life-cycle cost for the space station mission.

  20. Advanced instrumentation for next-generation aerospace propulsion control systems

    NASA Technical Reports Server (NTRS)

    Barkhoudarian, S.; Cross, G. S.; Lorenzo, Carl F.

    1993-01-01

    New control concepts for the next generation of advanced air-breathing and rocket engines and hypersonic combined-cycle propulsion systems are analyzed. The analysis provides a database on the instrumentation technologies for advanced control systems and cross matches the available technologies for each type of engine to the control needs and applications of the other two types of engines. Measurement technologies that are considered to be ready for implementation include optical surface temperature sensors, an isotope wear detector, a brushless torquemeter, a fiberoptic deflectometer, an optical absorption leak detector, the nonintrusive speed sensor, and an ultrasonic triducer. It is concluded that all 30 advanced instrumentation technologies considered can be recommended for further development to meet need of the next generation of jet-, rocket-, and hypersonic-engine control systems.

  1. Advanced instrumentation for next-generation aerospace propulsion control systems

    NASA Astrophysics Data System (ADS)

    Barkhoudarian, S.; Cross, G. S.; Lorenzo, Carl F.

    1993-06-01

    New control concepts for the next generation of advanced air-breathing and rocket engines and hypersonic combined-cycle propulsion systems are analyzed. The analysis provides a database on the instrumentation technologies for advanced control systems and cross matches the available technologies for each type of engine to the control needs and applications of the other two types of engines. Measurement technologies that are considered to be ready for implementation include optical surface temperature sensors, an isotope wear detector, a brushless torquemeter, a fiberoptic deflectometer, an optical absorption leak detector, the nonintrusive speed sensor, and an ultrasonic triducer. It is concluded that all 30 advanced instrumentation technologies considered can be recommended for further development to meet need of the next generation of jet-, rocket-, and hypersonic-engine control systems.

  2. Impacts of Mercury Pollution Controls on Atmospheric Mercury Concentration and Occupational Mercury Exposure in a Hospital.

    PubMed

    Li, Ping; Yang, Yan; Xiong, Wuyan

    2015-12-01

    Mercury (Hg) and Hg-containing products are used in a wide range of settings in hospitals. Hg pollution control measures were carried out in the pediatric ward of a hospital to decrease the possibility of Hg pollution occurring and to decrease occupational Hg exposure. Total gaseous Hg (TGM) concentrations in the pediatric ward and hair and urine Hg concentrations for the pediatric staff were determined before and after the Hg pollution control measures had been implemented. A questionnaire survey performed indicated that the pediatric staff had little understanding of Hg pollution and that appropriate disposal techniques were not always used after Hg leakage. TGM concentrations in the pediatric ward and urine Hg (UHg) concentrations for the pediatric staff were 25.7 and 22.2% lower, respectively, after the Hg pollution control measures had been implemented than before, which indicated that the control measures were effective. However, TGM concentrations in the pediatric ward remained significantly higher than background concentrations and UHg concentrations for the pediatric staff were remained significantly higher than the concentrations in control group, indicating continued existence of certain Hg pollution.

  3. Relationship between air pollution and pre-eclampsia in pregnant women: a case-control study.

    PubMed

    Nahidi, F; Gholami, R; Rashidi, Y; Majd, H Alavi

    2014-01-09

    Pre-eclampsia is the main cause of maternal and fetal death and disability worldwide. Its incidence in the Islamic Republic of Iran is 5%-12%. Air pollution has been reported to be one of the causative factors, and this case-control study determined its effect on pre-eclampsia in 195 pregnant women (65 with pre-eclampsia and 130 without) admitted to hospitals in Tehran. Women were divided into high and low exposure groups according to the mean density of exposure to pollutants during pregnancy. There was no statistically significant relationship between exposure to air pollutants including CO, particulate matter, SO2, NO2 and O3 and pre-eclampsia. The combined effect was also not significant. Air pollution is one of the problems of modern society and its avoidance is almost impossible for pregnant women. This study should reduce concern about pregnant women living in polluted cities.

  4. Development in Diagnostics Application to Control Advanced Tokamak Plasma

    SciTech Connect

    Koide, Y.

    2008-03-12

    For continuous operation expected in DEMO, all the plasma current must be non-inductively driven, with self-generated neoclassical bootstrap current being maximized. The control of such steady state high performance tokamak plasma (so-called 'Advanced Tokamak Plasma') is a challenge because of the strong coupling between the current density, the pressure profile and MHD stability. In considering diagnostic needs for the advanced tokamak research, diagnostics for MHD are the most fundamental, since discharges which violate the MHD stability criteria either disrupt or have significantly reduced confinement. This report deals with the development in diagnostic application to control advanced tokamak plasma, with emphasized on recent progress in active feedback control of the current profile and the pressure profile under DEMO-relevant high bootstrap-current fraction. In addition, issues in application of the present-day actuators and diagnostics for the advanced control to DEMO will be briefly addressed, where port space for the advanced control may be limited so as to keep sufficient tritium breeding ratio (TBR)

  5. 40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... Compliance Requirements § 60.2151 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution...

  6. 40 CFR 424.40 - Applicability; description of the covered calcium carbide furnaces with wet air pollution control...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... covered calcium carbide furnaces with wet air pollution control devices subcategory. 424.40 Section 424.40... FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Covered Calcium Carbide Furnaces With Wet Air Pollution... with wet air pollution control devices subcategory. The provisions of this subpart are applicable...

  7. 40 CFR 60.2151 - By what date must I conduct the annual air pollution control device inspection?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... air pollution control device inspection? 60.2151 Section 60.2151 Protection of Environment... Compliance Requirements § 60.2151 By what date must I conduct the annual air pollution control device inspection? On an annual basis (no more than 12 months following the previous annual air pollution...

  8. 40 CFR 424.40 - Applicability; description of the covered calcium carbide furnaces with wet air pollution control...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... covered calcium carbide furnaces with wet air pollution control devices subcategory. 424.40 Section 424.40... FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Covered Calcium Carbide Furnaces With Wet Air Pollution... with wet air pollution control devices subcategory. The provisions of this subpart are applicable...

  9. 40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating...

  10. 40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating...

  11. 40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating...

  12. 40 CFR 424.40 - Applicability; description of the covered calcium carbide furnaces with wet air pollution control...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... covered calcium carbide furnaces with wet air pollution control devices subcategory. 424.40 Section 424.40... FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Covered Calcium Carbide Furnaces With Wet Air Pollution... with wet air pollution control devices subcategory. The provisions of this subpart are applicable...

  13. 40 CFR 424.40 - Applicability; description of the covered calcium carbide furnaces with wet air pollution control...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... covered calcium carbide furnaces with wet air pollution control devices subcategory. 424.40 Section 424.40... FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Covered Calcium Carbide Furnaces With Wet Air Pollution... with wet air pollution control devices subcategory. The provisions of this subpart are applicable...

  14. 40 CFR 60.4895 - By what date must I conduct annual air pollution control device inspections and make any...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Compliance Requirements § 60.4895 By what date must I conduct annual air pollution control device inspections and make any necessary repairs? (a) You must conduct an annual inspection of each air pollution... following the previous annual air pollution control device inspection. (b) Within 10 operating...

  15. 40 CFR 424.40 - Applicability; description of the covered calcium carbide furnaces with wet air pollution control...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... covered calcium carbide furnaces with wet air pollution control devices subcategory. 424.40 Section 424.40... FERROALLOY MANUFACTURING POINT SOURCE CATEGORY Covered Calcium Carbide Furnaces With Wet Air Pollution... with wet air pollution control devices subcategory. The provisions of this subpart are applicable...

  16. Controlling adsorbate interactions for advanced chemical patterning

    NASA Astrophysics Data System (ADS)

    Saavedra Garcia, Hector M.

    Molecules designed to have specific interactions were used to influence the structural, physical, and chemical properties of self-assembled monolayers. In the case of 1-adamantanethiolate monolayers, the molecular structure influences lability, enabling alkanethiol molecules in solution to displace the 1-adamantanethiolate monolayers, ultimately leading to complete molecular exchange. The similar Au-S bond environments measured for both n-alkanethiolate and 1-adamantanethiolate monolayers indicate that displacement is not a result of weakened Au-S bonds. Instead, it was hypothesized that the density differences in the two monolayers provide a substantial enthalpic driver, aided by differences in van der Waals forces, ultimately leading to complete displacement of the 1-adamantenthiol molecules. Additionally, it was discovered that displacement occurs via fast insertion of n-dodecanethiolate at the defects in the original 1-adamantanethiolate monolayer, which nucleates an island growth phase and is followed by slow ordering of the n-dodecanethiolate domains into a denser and more crystalline form. Langmuir-based kinetics, which describe alkanethiolate adsorption on bare Au{111}, fail to model this displacement reaction. Instead, a model of perimeter-dependent island growth yields good agreement with kinetic data over a 100-fold variation in n-dodecanethiol concentration. Rescaling the growth rate at each concentration collapses all the data onto a single universal curve, suggesting that displacement is a scale-free process. Exploiting the knowledge gained by studying 1-adamantethiolate monolayer displacement, a reversible molecular resist was developed, in which displacement is controlled via external stimuli. This methodology for the fabrication of controllably displaceable monolayers relies on carboxyl-functionalized self-assembled monolayers and in-situ Fischer esterification. Using an 11-mercaptoundecanoic acid monolayer as a model system, it was shown that in

  17. ADVANCED COMPRESSOR ENGINE CONTROLS TO ENHANCE OPERATION, RELIABILITY AND INTEGRITY

    SciTech Connect

    Gary D. Bourn; Jess W. Gingrich; Jack A. Smith

    2004-03-01

    This document is the final report for the ''Advanced Compressor Engine Controls to Enhance Operation, Reliability, and Integrity'' project. SwRI conducted this project for DOE in conjunction with Cooper Compression, under DOE contract number DE-FC26-03NT41859. This report addresses an investigation of engine controls for integral compressor engines and the development of control strategies that implement closed-loop NOX emissions feedback.

  18. A formal structure for advanced automatic flight-control systems

    NASA Technical Reports Server (NTRS)

    Meyer, G.; Cicolani, L. S.

    1975-01-01

    Techniques were developed for the unified design of multimode, variable authority automatic flight-control systems for powered-lift STOL and VTOL aircraft. A structure for such systems is developed to deal with the strong nonlinearities inherent in this class of aircraft, to admit automatic coupling with advanced air traffic control, and to admit a variety of active control tasks. The aircraft being considered is the augmentor wing jet STOL research aircraft.

  19. Langley Research Center contributions in advancing active control technology

    NASA Technical Reports Server (NTRS)

    Abel, I.; Newsom, J. R.

    1981-01-01

    The application of active control technology to reduce aeroelastic response of aircraft structures offers a potential for significant payoffs in terms of aerodynamic efficiency and weight savings. Some of the contributions of the Langley Research Center in advancing active control technology are described. Contributions are categorized into the development of appropriate analysis tools, control law synthesis methodology, and experimental investigations aimed at verifying both analysis and synthesis methodology.

  20. Urban pollution.

    PubMed

    Sancini, Angela; Tomei, Francesco; Tomei, Gianfranco; Caciari, Tiziana; Di Giorgio, Valeria; André, Jean-Claude; Palermo, Paola; Andreozzi, Giorgia; Nardone, Nadia; Schifano, Maria Pia; Fiaschetti, Maria; Cetica, Carlotta; Ciarrocca, Manuela

    2012-01-01

    Air pollution represents a health risk for people living in urban environment. Urban air consists in a complex mixture of chemicals and carcinogens and its effects on health can be summarized in acute respiratory effects, neoplastic nonneoplastic (e.g. chronic bronchitis) chronic respiratory effects, and effects on other organs and systems. Air pollution may be defined according to origin of the phenomena that determine it: natural causes (natural fumes, decomposition, volcanic ash) or anthropogenic causes which are the result of human activities (industrial and civil emissions). Transport is the sector that more than others contributes to the deterioration of air quality in cities. In this context, in recent years, governments of the territory were asked to advance policies aimed at solving problems related to pollution. In consideration of the many effects on health caused by pollution it becomes necessary to know the risks from exposure to various environmental pollutants and to limit and control their effects. Many are the categories of "outdoor" workers, who daily serve the in urban environment: police, drivers, newsagents, etc.

  1. Urban pollution.

    PubMed

    Sancini, Angela; Tomei, Francesco; Tomei, Gianfranco; Caciari, Tiziana; Di Giorgio, Valeria; André, Jean-Claude; Palermo, Paola; Andreozzi, Giorgia; Nardone, Nadia; Schifano, Maria Pia; Fiaschetti, Maria; Cetica, Carlotta; Ciarrocca, Manuela

    2012-01-01

    Air pollution represents a health risk for people living in urban environment. Urban air consists in a complex mixture of chemicals and carcinogens and its effects on health can be summarized in acute respiratory effects, neoplastic nonneoplastic (e.g. chronic bronchitis) chronic respiratory effects, and effects on other organs and systems. Air pollution may be defined according to origin of the phenomena that determine it: natural causes (natural fumes, decomposition, volcanic ash) or anthropogenic causes which are the result of human activities (industrial and civil emissions). Transport is the sector that more than others contributes to the deterioration of air quality in cities. In this context, in recent years, governments of the territory were asked to advance policies aimed at solving problems related to pollution. In consideration of the many effects on health caused by pollution it becomes necessary to know the risks from exposure to various environmental pollutants and to limit and control their effects. Many are the categories of "outdoor" workers, who daily serve the in urban environment: police, drivers, newsagents, etc. PMID:22888729

  2. Contributions of CCLM to advances in quality control.

    PubMed

    Kazmierczak, Steven C

    2013-01-01

    Abstract The discipline of laboratory medicine is relatively young when considered in the context of the history of medicine itself. The history of quality control, within the context of laboratory medicine, also enjoys a relatively brief, but rich history. Laboratory quality control continues to evolve along with advances in automation, measurement techniques and information technology. Clinical Chemistry and Laboratory Medicine (CCLM) has played a key role in helping disseminate information about the proper use and utility of quality control. Publication of important advances in quality control techniques and dissemination of guidelines concerned with laboratory quality control has undoubtedly helped readers of this journal keep up to date on the most recent developments in this field.

  3. Synergic system between photovoltaic module and microbial fuel cell with simultaneous pollution control

    NASA Astrophysics Data System (ADS)

    Vasyliv, Oresta; Dhere, Neelkanth G.

    2015-05-01

    Combined photovoltaic module-microbial fuel cell construction shows prospect of advanced autonomous functioning effective energy-production system with the possibility of round-the-clock power generation. Application of Desulfuromonas sp. as anode biocatalyst in photovoltaic (PV) - microbial fuel cell (MFC) could support highly effective eco-friendly energy derivation with simultaneous reduction of organic and inorganic wastes in water environment. D. acetoxidans is exoelectrogenic bacterium that supports S0-reduction with H2S formation and S0-oxidation while an electrode serves as the electron acceptor. Simultaneous sulfur redox processes enhance electron transfer to the electrode surface that may increase the effectiveness of microbial fuel cell performance. It was shown that D. acetoxidans IMV B-7384 possesses selective resistance to 0.5-2.5 mM of copper, iron, nickel, manganese and lead ions. Metal-resistant strains of this bacterium may help overcome H2S toxicity, which is produced because of dissimilative S0-reduction, since divalent cations will interact with sulfide ions, forming insoluble precipitates. Thus D. acetoxidans IMV B-7384 may be applied for remediation of toxic metal ions from water environments because of metal fixation in form of insoluble complexes of metal sulfides. D. acetoxidans IMV B-7384 is presumed to have the capability to convert organic compounds, such as malate, pyruvate, succinate and fumarate via reductive stage of tricarboxylic acid cycle. Thus application of effluents as anolyte in MFC, based on D. acetoxidans IMV B-7384, may cause decrease of its organic content with formation of simple benign constituents, such as CO2 and H2O. Hence the advanced system for eco-friendly energy generation with simultaneous water pollution control is proposed.

  4. Minimum Control Requirements for Advanced Life Support Systems

    NASA Technical Reports Server (NTRS)

    Boulange, Richard; Jones, Harry; Jones, Harry

    2002-01-01

    Advanced control technologies are not necessary for the safe, reliable and continuous operation of Advanced Life Support (ALS) systems. ALS systems can and are adequately controlled by simple, reliable, low-level methodologies and algorithms. The automation provided by advanced control technologies is claimed to decrease system mass and necessary crew time by reducing buffer size and minimizing crew involvement. In truth, these approaches increase control system complexity without clearly demonstrating an increase in reliability across the ALS system. Unless these systems are as reliable as the hardware they control, there is no savings to be had. A baseline ALS system is presented with the minimal control system required for its continuous safe reliable operation. This baseline control system uses simple algorithms and scheduling methodologies and relies on human intervention only in the event of failure of the redundant backup equipment. This ALS system architecture is designed for reliable operation, with minimal components and minimal control system complexity. The fundamental design precept followed is "If it isn't there, it can't fail".

  5. CONTROL OF POLLUTANT EMISSIONS IN NATURAL GAS DIFFUSION FLAMES BY USING CASCADE BURNERS

    SciTech Connect

    Dr. Ala Qubbaj

    2001-12-30

    The goal of this exploratory research project is to control the pollutant emissions of diffusion flames by modifying the air infusion rate into the flame. The modification was achieved by installing a cascade of venturis around the burning gas jet. The basic idea behind this technique is controlling the stoichiometry of the flame through changing the flow dynamics and rates of mixing in the combustion zone with a set of venturis surrounding the flame. A natural gas jet diffusion flame at burner-exit Reynolds number of 5100 was examined with a set of venturis of specific sizes and spacing arrangement. The thermal and composition fields of the baseline and venturi-cascaded flames were numerically simulated using CFD-ACE+, an advanced computational environment software package. The instantaneous chemistry model was used as the reaction model. The concentration of NO was determined through CFD-POST, a post processing utility program for CFD-ACE+. The numerical results showed that, in the near-burner, midflame and far-burner regions, the venturi-cascaded flame had lower temperature by an average of 13%, 19% and 17%, respectively, and lower CO{sub 2} concentration by 35%, 37% and 32%, respectively, than the baseline flame. An opposite trend was noticed for O{sub 2} concentration; the cascaded flame has higher O{sub 2} concentration by 7%, 26% and 44%, in average values, in the near-burner, mid-flame and far-burner regions, respectively, than in the baseline case. The results also showed that, in the near-burner, mid-flame, and far-burner regions, the venturi-cascaded flame has lower NO concentrations by 89%, 70% and 70%, in average values, respectively, compared to the baseline case. The numerical results substantiate that venturi-cascading is a feasible method for controlling the pollutant emissions of a burning gas jet. In addition, the numerical results were useful to understand the thermo-chemical processes involved. The results showed that the prompt-NO mechanism

  6. Using Nanomaterials In Risk Management Of Environmental Pollutants: An Overview Of Recent Advancements

    EPA Science Inventory

    Persistent organic pollutants, known as POPs, are toxic substances released into the environment by human activities. Of all POPs released into the environment by human activity, polychlorinated biphenyls (PCBs) are among the most dangerous. They are highly toxic, causing death...

  7. Quantification of local and global benefits from air pollution control in Mexico City.

    PubMed

    Mckinley, Galen; Zuk, Miriam; Höjer, Morten; Avalos, Montserrat; González, Isabel; Iniestra, Rodolfo; Laguna, Israel; Martínez, Miguel A; Osnaya, Patricia; Reynales, Luz M; Valdés, Raydel; Martínez, Julia

    2005-04-01

    Complex sociopolitical, economic, and geographical realities cause the 20 million residents of Mexico City to suffer from some of the worst air pollution conditions in the world. Greenhouse gas emissions from the city are also substantial, and opportunities for joint local-global air pollution control are being sought. Although a plethora of measures to improve local air quality and reduce greenhouse gas emissions have been proposed for Mexico City, resources are not available for implementation of all proposed controls and thus prioritization must occur. Yet policy makers often do not conduct comprehensive quantitative analyses to inform these decisions. We reanalyze a subset of currently proposed control measures, and derive cost and health benefit estimates that are directly comparable. This study illustrates that improved quantitative analysis can change implementation prioritization for air pollution and greenhouse gas control measures in Mexico City.

  8. [Research advances in identifying nitrate pollution sources of water environment by using nitrogen and oxygen stable isotopes].

    PubMed

    Mao, Wei; Liang, Zhi-wei; Li, Wei; Zhu, Yao; Yanng, Mu-yi; Jia, Chao-jie

    2013-04-01

    Water body' s nitrate pollution has become a common and severe environmental problem. In order to ensure human health and water environment benign evolution, it is of great importance to effectively identify the nitrate pollution sources of water body. Because of the discrepant composition of nitrogen and oxygen stable isotopes in different sources of nitrate in water body, nitrogen and oxygen stable isotopes can be used to identify the nitrate pollution sources of water environment. This paper introduced the fractionation factors of nitrogen and oxygen stable isotopes in the main processes of nitrogen cycling and the composition of these stable isotopes in main nitrate sources, compared the advantages and disadvantages of five pre-treatment methods for analyzing the nitrogen and oxygen isotopes in nitrate, and summarized the research advances in this aspect into three stages, i. e. , using nitrogen stable isotope alone, using nitrogen and oxygen stable isotopes simultaneously, and combining with mathematical models. The future research directions regarding the nitrate pollution sources identification of water environment were also discussed.

  9. EPA`s adaptive controls system research program for pollution prevention and clean technologies. Report for October 1991-March 1995

    SciTech Connect

    Spiegel, R.J.; Chappell, P.J.; Miller, C.A.

    1995-03-01

    EPA`s control systems research is concentrated in three areas: electric motors, wind turbines, and combustion technologies. In general, these projects are concerned with pollution prevention through enhanced efficiency of operation and pollution control through lower emission levels. Pioneering effort has been achieved in the application of fuzzy-logic-based controls in these areas. Based on the results of these projects, fuzzy logic has emerged as an important tool in environmental technology for pollution elimination and control.

  10. Overview of the US program of controls for advanced reactors

    SciTech Connect

    White, J.D.; Sackett, J.I.; Monson, R.; Lindsay, R.W.; Carroll, D.G.

    1989-01-01

    An automated control system can incorporate control goals and strategies, assessment of present and future plant status, diagnostic evaluation and maintenance planning, and signal and command validation. It has not been feasible to employ these capabilities in conventional hard-wired, analog, control systems. Recent advances in computer-based digital data acquisition systems, process controllers, fiber-optic signal transmission artificial intelligence tools and methods, and small inexpensive, fast, large-capacity computers---with both numeric and symbolic capabilities---have provided many of the necessary ingredients for developing large, practical automated control systems. Furthermore, recent reactor designs which provide strong passive responses to operational upsets or accidents afford good opportunities to apply these advances in control technology. This paper presents an overall US national perspective for advanced controls research and development. The goals of high reliability, low operating cost and simple operation are described. The staged approach from conceptualization through implementation is discussed. Then the paper describes the work being done by ORNL, ANL and GE. The relationship of this work to the US commercial industry is also discussed.

  11. Advanced helicopter cockpit and control configurations for helicopter combat missions

    NASA Technical Reports Server (NTRS)

    Haworth, Loran A.; Atencio, Adolph, Jr.; Bivens, Courtland; Shively, Robert; Delgado, Daniel

    1987-01-01

    Two piloted simulations were conducted by the U.S. Army Aeroflightdynamics Directorate to evaluate workload and helicopter-handling qualities requirements for single pilot operation in a combat Nap-of-the-Earth environment. The single-pilot advanced cockpit engineering simulation (SPACES) investigations were performed on the NASA Ames Vertical Motion Simulator, using the Advanced Digital Optical Control System control laws and an advanced concepts glass cockpit. The first simulation (SPACES I) compared single pilot to dual crewmember operation for the same flight tasks to determine differences between dual and single ratings, and to discover which control laws enabled adequate single-pilot helicopter operation. The SPACES II simulation concentrated on single-pilot operations and use of control laws thought to be viable candidates for single pilot operations workload. Measures detected significant differences between single-pilot task segments. Control system configurations were task dependent, demonstrating a need for inflight reconfigurable control system to match the optimal control system with the required task.

  12. Comparison of Advanced Distillation Control Methods, Final Technical Report

    SciTech Connect

    Dr. James B. Riggs

    2000-11-30

    Detailed dynamic simulations of three industrial distillation columns (a propylene/propane splitter, a xylene/toluene column, and a depropanizer) have been used to evaluate configuration selections for single-ended and dual-composition control, as well as to compare conventional and advanced control approaches. In addition, a simulator of a main fractionator was used to compare the control performance of conventional and advanced control. For each case considered, the controllers were tuned by using setpoint changes and tested using feed composition upsets. Proportional Integral (PI) control performance was used to evaluate the configuration selection problem. For single ended control, the energy balance configuration was found to yield the best performance. For dual composition control, nine configurations were considered. It was determined that the use of dynamic simulations is required in order to identify the optimum configuration from among the nine possible choices. The optimum configurations were used to evaluate the relative control performance of conventional PI controllers, MPC (Model Predictive Control), PMBC (Process Model-Based Control), and ANN (Artificial Neural Networks) control. It was determined that MPC works best when one product is much more important than the other, while PI was superior when both products were equally important. PMBC and ANN were not found to offer significant advantages over PI and MPC. MPC was found to outperform conventional PI control for the main fractionator. MPC was applied to three industrial columns: one at Phillips Petroleum and two at Union Carbide. In each case, MPC was found to significantly outperform PI controls. The major advantage of the MPC controller is its ability to effectively handle a complex set of constraints and control objectives.

  13. Associations between urban air pollution and pediatric asthma control in El Paso, Texas.

    PubMed

    Zora, Jennifer E; Sarnat, Stefanie Ebelt; Raysoni, Amit U; Johnson, Brent A; Li, Wen-Whai; Greenwald, Roby; Holguin, Fernando; Stock, Thomas H; Sarnat, Jeremy A

    2013-03-15

    Exposure to traffic-related pollutants poses a serious health threat to residents of major urban centers around the world. In El Paso, Texas, this problem is exacerbated by the region's arid weather, frequent temperature inversions, heavy border traffic, and an aged, poorly maintained vehicle fleet. The impact of exposure to traffic pollution, particularly on children with asthma, is poorly understood. Tracking the environmental health burden related to traffic pollution in El Paso is difficult, especially within school microenvironments, because of the lack of sensitive environmental health indicator data. The Asthma Control Questionnaire (ACQ) is a survey tool for the measurement of overall asthma control, yet has not previously been considered as an outcome in air pollution health effect research. We conducted a repeated measure panel study to examine weekly associations between ACQ scores and traffic- and non-traffic air pollutants among asthmatic schoolchildren in El Paso. In the main one- and two-pollutant epidemiologic models, we found non-significant, albeit suggestive, positive associations between ACQ scores and respirable particulate matter (PM10), coarse particulate matter (PM10-2.5), fine particulate matter (PM2.5), black carbon (BC), nitrogen dioxide (NO2), benzene, toluene, and ozone (O3). Notably, associations were stronger and significant for some subgroups, in particular among subjects taking daily inhaled corticosteroids. This pattern may indicate heightened immune system response in more severe asthmatics, those with worse asthma "control" and higher ACQ scores at baseline. If the ACQ is appropriately used in the context of air pollution studies, it could reflect clinically measurable and biologically relevant changes in lung function and asthma symptoms that result from poor air quality and may increase our understanding of how air pollution influences asthma exacerbation.

  14. INTEGRATED AIR POLLUTION CONTROL SYSTEM, VERSION 4.0 - VOLUME 2: TECHNICAL DOCUMENTATION MANUAL

    EPA Science Inventory

    The Integrated Air Pollution Control System (IAPCS) was developed for the U.S. EPA's Air and Energy Engineering Research Laboratory to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, and ...

  15. INTEGRATED AIR POLLUTION CONTROL SYSTEM, VERSION 4.0 - VOLUME 3: PROGRAMMER'S MAINTENACE MANUAL

    EPA Science Inventory

    The Integrated Air Pollution Control System (IAPCS) was developed for the U.S. EPA's Air and Energy Engineering Research Laboratory to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, and ...

  16. INTEGRATED AIR POLLUTION CONTROL SYSTEM, VERSION 4.0 - VOLUME 1: USER'S GUIDE

    EPA Science Inventory

    The Integrated Air Pollution Control System (IAPCS) was developed for the U.S. EPA's Air and Energy Engineering Research Laboratory to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, and ...

  17. INTEGRATED AIR POLLUTION CONTROL SYSTEM VERSION 5.0 - VOLUME 1: USER'S GUIDE

    EPA Science Inventory

    The three volume report and two diskettes document the Integrated Air Pollution Control System (IAPCS), developed for the U.S. EPA to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, an eq...

  18. INTEGRATED AIR POLLUTION CONTROL SYSTEM VERSION 5.0 - VOLUME 2: TECHNICAL DOCUMENTATION

    EPA Science Inventory

    The three volume report and two diskettes document the Integrated Air Pollution Control System (IAPCS), developed for the U.S. EPA to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, an eq...

  19. INTEGRATED AIR POLLUTION CONTROL SYSTEM VERSION 5.0 - VOLUME 3: PROGRAMMER'S MAINTENANCE MANUAL

    EPA Science Inventory

    The three volume report and two diskettes document the Integrated Air Pollution Control System (IAPCS), developed for the U.S. EPA to estimate costs and performance for emission control systems applied to coal-fired utility boilers. The model can project a material balance, an eq...

  20. Water Pollution Control Training: The Educational Role of the United States Environmental Protection Agency.

    ERIC Educational Resources Information Center

    Williams, Frederick D.

    Presented are the results of a study to determine the perceived needs of environmental control education programs as seen by students, instructors, deans or program directors, and field-related employers in the field of water pollution control. Data were collected utilizing three approaches: survey instruments, information from Water Quality…

  1. Action for Environmental Quality. Standards and Enforcement for Air and Water Pollution Control.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC.

    The U.S. Environmental Protection Agency (EPA) is responsible for setting and enforcing environmental quality standards for the nation. With the Clean Air Act of 1970 (P.L. 91-604) and the Water Pollution Control Act of 1972 (P.L. 92-500), the first truly nationwide control programs were established. This booklet is designed to inform the public…

  2. 48 CFR 452.236-74 - Control of Erosion, Sedimentation, and Pollution.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... scheduled and conducted to minimize erosion of soils and to prevent silting and muddying of streams, rivers... 48 Federal Acquisition Regulations System 4 2013-10-01 2013-10-01 false Control of Erosion....236-74 Control of Erosion, Sedimentation, and Pollution. As prescribed in 436.574, insert...

  3. 48 CFR 452.236-74 - Control of Erosion, Sedimentation, and Pollution.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... scheduled and conducted to minimize erosion of soils and to prevent silting and muddying of streams, rivers... 48 Federal Acquisition Regulations System 4 2011-10-01 2011-10-01 false Control of Erosion....236-74 Control of Erosion, Sedimentation, and Pollution. As prescribed in 436.574, insert...

  4. 48 CFR 452.236-74 - Control of Erosion, Sedimentation, and Pollution.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... scheduled and conducted to minimize erosion of soils and to prevent silting and muddying of streams, rivers... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Control of Erosion....236-74 Control of Erosion, Sedimentation, and Pollution. As prescribed in 436.574, insert...

  5. 48 CFR 452.236-74 - Control of Erosion, Sedimentation, and Pollution.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... scheduled and conducted to minimize erosion of soils and to prevent silting and muddying of streams, rivers... 48 Federal Acquisition Regulations System 4 2014-10-01 2014-10-01 false Control of Erosion....236-74 Control of Erosion, Sedimentation, and Pollution. As prescribed in 436.574, insert...

  6. 76 FR 44809 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-27

    ... Control District and Feather River Air Quality Management District ACTION: Final rule. SUMMARY: EPA is... Pollution Control District (PCAPCD) and Feather River Air Quality Management District (FRAQMD) portions of... and Executive Order Reviews I. Proposed Action On May 19, 2011 (76 FR 28944), EPA proposed a...

  7. 76 FR 71886 - Revisions to the California State Implementation Plan, Placer County Air Pollution Control...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-21

    ... Control District and Sacramento Metropolitan Air Quality Management District AGENCY: Environmental... Office of Management and Budget under Executive Order 12866 (58 FR 51735, October 4, 1993); Does not... revisions to the Placer County Air Pollution Control District (PCAPCD) and Sacramento Metropolitan...

  8. Vision Based Autonomous Robotic Control for Advanced Inspection and Repair

    NASA Technical Reports Server (NTRS)

    Wehner, Walter S.

    2014-01-01

    The advanced inspection system is an autonomous control and analysis system that improves the inspection and remediation operations for ground and surface systems. It uses optical imaging technology with intelligent computer vision algorithms to analyze physical features of the real-world environment to make decisions and learn from experience. The advanced inspection system plans to control a robotic manipulator arm, an unmanned ground vehicle and cameras remotely, automatically and autonomously. There are many computer vision, image processing and machine learning techniques available as open source for using vision as a sensory feedback in decision-making and autonomous robotic movement. My responsibilities for the advanced inspection system are to create a software architecture that integrates and provides a framework for all the different subsystem components; identify open-source algorithms and techniques; and integrate robot hardware.

  9. Second Generation Advanced Reburning for High Efficiency NOx Control

    SciTech Connect

    Vladimir M. Zamansky; Peter M. Maly; Vitali V. Lissianski

    1999-06-30

    This project is designed to develop a family of novel NO{sub x} control technologies, called Second Generation Advanced Reburning which has the potential to achieve 90+ NO{sub x} control in coal fired boilers at a significantly lower cost than Selective Catalytic Reduction. The seventh reporting period in Phase II (April 1-June 30, 1999) included experimental activities and combined chemistry-mixing modeling on advanced gas reburning. The goal of combustion tests was to determine the efficiency of advanced reburning using coal as the reburning fuel. Tests were conducted in Boiler Simulator Facility (BSF). Several coals were tested. The modeling effort was focused on the description of N-agent injection along with overfire air. Modeling identified process parameters that can be used to optimize the AR-Lean process.

  10. Second Generation Advanced Reburning for High Efficiency NOx Control

    SciTech Connect

    Vladimir M. Zamansky; Pete M. Maly

    2000-03-31

    This project is designed to develop a family of novel NO{sub x} control technologies, called Second Generation Advanced Reburning (SGAR) which has the potential to achieve 90+ NO{sub x} control in coal fired boilers at a significantly lower cost than Selective Catalytic Reduction. The tenth reporting period in Phase II (January 1-March 31, 2000) included proof-of concept tests in the 10 x 10{sup 6} Btu/hr Tower Furnace. Several variants of Second Generation Advanced Reburning (SGAR) were studied, including AR-Lean, AR-Rich, reburning + SNCR, and Multiple Injection Advanced Reburning (MIAR). Tests demonstrated that the SGAR performance was the most effective under MIAR conditions achieving maximum overall NO{sub x} reduction of 96%.

  11. Key issues in controlling air pollutants in Dhaka, Bangladesh

    NASA Astrophysics Data System (ADS)

    Begum, Bilkis A.; Biswas, Swapan K.; Hopke, Philip K.

    2011-12-01

    Particulate matter (PM) sampling for both coarse and fine fractions was conducted in a semi-residential site (AECD) in Dhaka from February 2005 to December 2006. The samples were analyzed for mass, black carbon (BC), and elemental compositions. The resulting data set were analyzed for sources by Positive Matrix Factorization (EPA-PMF). From previous studies, it is found that, the air quality became worse in the dry winter period compared to the rainy season because of higher particulate matter concentration in the ambient air. Therefore, seasonal source contributions were determined from seasonally segregated data using EPA-PMF modeling so that further policy interventions can be undertaken to improve air quality. From the source apportionment results, it is observed that vehicular emissions and emission from brick kiln are the major contributors to air pollution in Dhaka especially in the dry seasons, while contribution from emissions from metal smelters increases during rainy seasons. The Government of Bangladesh is considering different interventions to reduce the emissions from those sources by adopting conversion of diesel/petrol vehicles to CNG, increasing traffic speed in the city and by introducing green technologies for brick production. However, in order to reduce the transboundary effect it is necessary to take action regionally.

  12. Status report on the Advanced Light Source control system, 1993

    SciTech Connect

    Young, J.; Brown, W. Jr.; Cork, C.

    1993-10-01

    The Advanced Light Source (ALS), under construction for the past seven years, has become operational. The accelerator has been successfully commissioned using a control system based on hundreds of controllers of our own design and high performance personal computers which are the operator interface. The first beamlines are being commissioned using a control system based on VME hardware and the Experimental Physics and Industrial Control System (EPICS) software. The two systems are being integrated, and this paper reports on the current work being done.

  13. Advanced control for airbreathing engines, volume 1: Pratt and Whitney

    NASA Technical Reports Server (NTRS)

    Ralph, J. A.

    1993-01-01

    The application of advanced control concepts to air breathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for air breathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 1 of these reports describes the studies performed by Pratt & Whitney.

  14. Advanced controls for airbreathing engines, volume 3: Allison gas turbine

    NASA Technical Reports Server (NTRS)

    Bough, R. M.

    1993-01-01

    The application of advanced control concepts to airbreathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for airbreathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two-phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 3 of these reports describes the studies performed by the Allison Gas Turbine Division.

  15. Advances in developing alternative treatments for postharvest pest control

    Technology Transfer Automated Retrieval System (TEKTRAN)

    USDA-ARS made two significant advances in the last 10 years in the development of alternative treatments for postharvest pest control: oxygenated phosphine fumigation and nitric oxide fumigation. Oxygenated phosphine is phosphine fumigation in an oxygen enriched atmosphere. It is significantly more...

  16. Outdoor Air Pollution and Cardiovascular Diseases in Lebanon: A Case-Control Study

    PubMed Central

    Nasser, Zeina; Salameh, Pascale; Dakik, Habib; Elias, Elias; Abou Abbas, Linda; Levêque, Alain

    2015-01-01

    Outdoor air pollution is increasingly considered as a serious threat for cardiovascular diseases (CVD). The aim of this study is to investigate the association between outdoor pollutants and cardiovascular diseases among adults in Lebanon and to examine the possible moderator effect of cigarette smoking status on this association. A multicenter case-control study was conducted between October 2011 and October 2012. Cases were hospitalized patients diagnosed with CVD by a cardiologist while the control group subjects were free of any cardiac diseases. Information on sociodemographic characteristics, tobacco consumption, self-rated global health, pollution exposure, and other risk factors was collected using a questionnaire. The results of the logistic regression revealed that living near busy highway (OR 5.04, 95% CI (4.44–12.85), P < 0.001) and close to local diesel generator (OR 4.76, 95% CI (2.07–10.91), P < 0.001) was significantly associated with CVD. The association between the CVD and exposure to outside pollutants differed by cigarette smoking status. A clear difference was noted between nonsmokers and current smokers OR 4.6, 95% CI (1.10–19.25) and OR 10.11, 95% CI (7.33–20.23), respectively. Forthcoming studies are needed to clarify the potential link between outdoor air pollution and cardiovascular diseases in Lebanon. Public health interventions must be implemented to reduce air pollution and to improve air quality. PMID:25653681

  17. Supervisory Control System Architecture for Advanced Small Modular Reactors

    SciTech Connect

    Cetiner, Sacit M; Cole, Daniel L; Fugate, David L; Kisner, Roger A; Melin, Alexander M; Muhlheim, Michael David; Rao, Nageswara S; Wood, Richard Thomas

    2013-08-01

    This technical report was generated as a product of the Supervisory Control for Multi-Modular SMR Plants project within the Instrumentation, Control and Human-Machine Interface technology area under the Advanced Small Modular Reactor (SMR) Research and Development Program of the U.S. Department of Energy. The report documents the definition of strategies, functional elements, and the structural architecture of a supervisory control system for multi-modular advanced SMR (AdvSMR) plants. This research activity advances the state-of-the art by incorporating decision making into the supervisory control system architectural layers through the introduction of a tiered-plant system approach. The report provides a brief history of hierarchical functional architectures and the current state-of-the-art, describes a reference AdvSMR to show the dependencies between systems, presents a hierarchical structure for supervisory control, indicates the importance of understanding trip setpoints, applies a new theoretic approach for comparing architectures, identifies cyber security controls that should be addressed early in system design, and describes ongoing work to develop system requirements and hardware/software configurations.

  18. Alternative approaches to pollution control and waste management: Regulatory and economic instruments

    SciTech Connect

    Bernstein, J.D.

    1993-01-01

    The purpose of the paper is to present an overview of the most common strategies and policy instruments (that is, regulatory and economic) used in developed and developing countries to achieve pollution control and waste management objectives. Although this topic has been at the center of theoretical controversy both within and outside the World Bank, the paper is not intended to contribute to this debate. Rather, its purpose is to explore how regulatory and economic instruments are used to control air and water pollution, protect ground water, and manage solid and hazardous wastes. The paper is directed to policy makers at the national, state, and local levels of government, as well as to other parties responsible for pollution control and waste management programs.

  19. Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment.

    PubMed

    Li, Juan; Yang, Yang; Huan, Huan; Li, Mingxiao; Xi, Beidou; Lv, Ningqing; Wu, Yi; Xie, Yiwen; Li, Xiang; Yang, Jinjin

    2016-05-01

    This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China. PMID:26878632

  20. Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment.

    PubMed

    Li, Juan; Yang, Yang; Huan, Huan; Li, Mingxiao; Xi, Beidou; Lv, Ningqing; Wu, Yi; Xie, Yiwen; Li, Xiang; Yang, Jinjin

    2016-05-01

    This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China.

  1. Controlling death: the false promise of advance directives.

    PubMed

    Perkins, Henry S

    2007-07-01

    Advance directives promise patients a say in their future care but actually have had little effect. Many experts blame problems with completion and implementation, but the advance directive concept itself may be fundamentally flawed. Advance directives simply presuppose more control over future care than is realistic. Medical crises cannot be predicted in detail, making most prior instructions difficult to adapt, irrelevant, or even misleading. Furthermore, many proxies either do not know patients' wishes or do not pursue those wishes effectively. Thus, unexpected problems arise often to defeat advance directives, as the case in this paper illustrates. Because advance directives offer only limited benefit, advance care planning should emphasize not the completion of directives but the emotional preparation of patients and families for future crises. The existentialist Albert Camus might suggest that physicians should warn patients and families that momentous, unforeseeable decisions lie ahead. Then, when the crisis hits, physicians should provide guidance; should help make decisions despite the inevitable uncertainties; should share responsibility for those decisions; and, above all, should courageously see patients and families through the fearsome experience of dying.

  2. Pollution Probe.

    ERIC Educational Resources Information Center

    Chant, Donald A.

    This book is written as a statement of concern about pollution by members of Pollution Probe, a citizens' anti-pollution group in Canada. Its purpose is to create public awareness and pressure for the eventual solution to pollution problems. The need for effective government policies to control the population explosion, conserve natural resources,…

  3. Science, technology and policy for Water Pollution Control at the Watershed Scale: Current issues and future challenges

    NASA Astrophysics Data System (ADS)

    Ghadouani, Anas; Coggins, Liah X.

    Water is a critical resource, and the shortage of freshwater resources worldwide will only become more critical as the world population increases and climate changes. The management of water resources provides a myriad of challenges, and, in light of advances in science, technology and policy making, now requires an integrated approach to be successful. Eutrophication and algal blooms are one of the most common and serious threats to the safety and security of water resources; however, despite advances in science and policy, the socio-economic consequences of the impact of such events on systems are still not well known. The economic cost of managing water quality issues is enormous, and can only benefit from the development of more integrated water management strategies. Research into areas related to water resources, such as management, policy, non-point source pollutants, wastewater, nutrients and water quality has increased significantly over the past 20 years, and will continue to increase as stakeholders and managers strive to develop more environmentally, socially, and economically sustainable water resource management plans. This perspective paper also presents a summary of a selection of research that formed part of the deliberations of the International Symposium on Science, Technology and Policy for Water Pollution Control at the Watershed Scale, held in April 2009.

  4. Spectrophotometric Procedure for Fast Reactor Advanced Coolant Manufacture Control

    NASA Astrophysics Data System (ADS)

    Andrienko, O. S.; Egorov, N. B.; Zherin, I. I.; Indyk, D. V.

    2016-01-01

    The paper describes a spectrophotometric procedure for fast reactor advanced coolant manufacture control. The molar absorption coefficient of dimethyllead dibromide with dithizone was defined as equal to 68864 ± 795 l·mole-1·cm-1, limit of detection as equal to 0.583 · 10-6 g/ml. The spectrophotometric procedure application range was found to be equal to 37.88 - 196.3 g. of dimethyllead dibromide in the sample. The procedure was used within the framework of the development of the method of synthesis of the advanced coolant for fast reactors.

  5. Comprehensive sampling program for the Y-12 Plant area source pollution assessment and control plan

    SciTech Connect

    Kingrea, R.H.; Arniella, E.F.; Roesner, L.A.; Quasebarth, T.

    1987-10-15

    The Y-12 Plant has begun an aggressive program for identifying and controlling nonpoint pollution discharges to East Fork Poplar Creek (EFPC). Nonpoint source discharges, also referred to as area source discharges, result when surface water or ground water flows though contaminated surfaces resulting in the transport of pollutants to a receiving stream. This paper presents the approach undertaken by the project team to implement a comprehensive sampling program of the EFPC drainage area. The results of the comprehensive sampling program will be used to establish best management practices for the control of nonpoint sources in the EFPC drainage area. 5 refs., 2 tabs.

  6. Advances in Analytical and Numerical Dispersion Modeling of Pollutants Releasing from an Area-source

    NASA Astrophysics Data System (ADS)

    Nimmatoori, Praneeth

    The air quality near agricultural activities such as tilling, plowing, harvesting, and manure application is of main concern because they release fine particulate matter into the atmosphere. These releases are modeled as area-sources in the air quality modeling research. None of the currently available dispersion models relate and incorporate physical characteristics and meteorological conditions for modeling the dispersion and deposition of particulates emitting from such area-sources. This knowledge gap was addressed by developing the advanced analytical and numerical methods for modeling the dispersion of particulate matter. The development, application, and evaluation of new dispersion modeling methods are discussed in detail in this dissertation. In the analytical modeling, a ground-level area source analytical dispersion model known as particulate matter deposition -- PMD was developed for predicting the concentrations of different particle sizes. Both the particle dynamics (particle physical characteristics) and meteorological conditions which have significant effect on the dispersion of particulates were related and incorporated in the PMD model using the formulations of particle gravitational settling and dry deposition velocities. The modeled particle size concentrations of the PMD model were evaluated statistically after applying it to particulates released from a biosolid applied agricultural field. The evaluation of the PMD model using the statistical criteria concluded effective and successful inclusion of dry deposition theory for modeling particulate matter concentrations. A comprehensive review of analytical area-source dispersion models, which do not account for dry deposition and treat pollutants as gases, was conducted and determined three models -- the Shear, the Parker, and the Smith. A statistical evaluation of these dispersion models was conducted after applying them to two different field data sets and the statistical results concluded that

  7. The DPC-2000 advanced control system for the Dynamitron accelerator

    NASA Astrophysics Data System (ADS)

    Kestler, Bernard A.; Lisanti, Thomas F.

    1993-07-01

    The DPC-2000 is an advanced control system utilizing the latest technology in computer control circuitry and components. Its overall design is modular and technologically advanced to keep up with customer and engineering demands. The full control system is presented as four units. They are the Remote I/O (Input / Output), Local Analog and Digital I/O, Operator Interface and the Main Computer. The central processing unit, the heart of the system, executes a high level language program that communicates to the different sub-assemblies through advanced serial and parallel communication lines. All operational parameters of the accelerator are monitored, controlled and corrected at close to 20 times per second. The operator is provided with a selection of many informative screen displays. The control program handles all graphic screen displays and the updating of these screens directly; it does not have to communicate to a display terminal. This adds to the quick response and excellent operator feedback received while operating the machine. The CPU also has the ability to store and record all process variable setpoints for each product that will be treated. This allows the operator to set up the process parameters by selecting the product identification code from a menu presented on the display screen. All process parameters are printed to report at regular intervals during a process run for later analysis and record keeping.

  8. Advanced actuators for the control of large space structures

    NASA Technical Reports Server (NTRS)

    Downer, James; Hockney, Richard; Johnson, Bruce; Misovec, Kathleen

    1993-01-01

    The objective of this research was to develop advanced six-degree-of-freedom actuators employing magnetic suspensions suitable for the control of structural vibrations in large space structures. The advanced actuators consist of a magnetically suspended mass that has three-degrees-of-freedom in both translation and rotation. The most promising of these actuators featured a rotating suspended mass providing structural control torques in a manner similar to a control moment gyro (CMG). These actuators employ large-angle-magnetic suspensions that allow gimballing of the suspended mass without mechanical gimbals. Design definitions and sizing algorithms for these CMG type as well as angular reaction mass actuators based on multi-degree-of-freedom magnetic suspensions were developed. The performance of these actuators was analytically compared with conventional reaction mass actuators for a simple space structure model.

  9. An investigation of air emission levels from distinct iron and steel production processes with the adoption of pollution control and pollution prevention alternatives

    SciTech Connect

    Costa, M.M.; Schaeffer, R.

    1999-07-01

    This paper aims to investigate environmental aspects from different iron and steel production processes. A methodology based on material flows is developed in order to verify some air emission levels attained by Pollution Control and Pollution Prevention alternatives. The data basis for modeling energy and materials flows in iron and steel production is obtained from a literature review on different technological processes, energy and materials consumption and pollutant releases to the environmental Modeling combines both process analysis and input-output techniques to simulate the different iron and steel production routes and to estimate the resulting total atmospheric pollution releases based on air emission factors for several pollutants by each production step. Processes examined include: (1) Conventional Integrated (100% ore-based and partly scrap-based); (2) Mini-mill with EAF (100% scrap-based and partly DRI-based); and (3) New Integrated based on the COREX smelting reduction process. Among the alternatives considered for air emissions reductions are those related to Pollution Control (mainly gas cleaning systems) and to Pollution Prevention (change/reduction in input materials, operational procedures and housekeeping improvements, on-site recycling and technology innovations and modifications). Results indicate higher air pollution intensity for the Conventional Integrated Route over the Mini-mill with EAF and COREX smelting reduction processes, though pointing out that final figures are strongly affected by the systems' boundaries and the different air emission levels of each production step.

  10. Planner-Based Control of Advanced Life Support Systems

    NASA Technical Reports Server (NTRS)

    Muscettola, Nicola; Kortenkamp, David; Fry, Chuck; Bell, Scott

    2005-01-01

    The paper describes an approach to the integration of qualitative and quantitative modeling techniques for advanced life support (ALS) systems. Developing reliable control strategies that scale up to fully integrated life support systems requires augmenting quantitative models and control algorithms with the abstractions provided by qualitative, symbolic models and their associated high-level control strategies. This will allow for effective management of the combinatorics due to the integration of a large number of ALS subsystems. By focusing control actions at different levels of detail and reactivity we can use faster: simpler responses at the lowest level and predictive but complex responses at the higher levels of abstraction. In particular, methods from model-based planning and scheduling can provide effective resource management over long time periods. We describe reference implementation of an advanced control system using the IDEA control architecture developed at NASA Ames Research Center. IDEA uses planning/scheduling as the sole reasoning method for predictive and reactive closed loop control. We describe preliminary experiments in planner-based control of ALS carried out on an integrated ALS simulation developed at NASA Johnson Space Center.

  11. SEWER AND TANK FLUSHING FOR CORROSION AND POLLUTION CONTROL

    EPA Science Inventory

    This paper presents an overview of the causes of sewer deterioration and control methods that can prevent or arrest this deterioration. articular, the paper addresses the use of inline- and combined sewer overflow (CSO) storage tank-flushing systems for removing sediments and mi...

  12. Tire Production and Pollution Control. Environmental Education Curriculum. Revised.

    ERIC Educational Resources Information Center

    Topeka Public Schools, KS.

    This unit was developed to introduce secondary students to the many facets of a typical, large manufacturing plant - the Topeka Goodyear Tire and Rubber Company - in an effort to increase awareness of sound environmental practices in industry. Its five major foci include the production of tires and quality control procedures; applications of…

  13. Development of an inexact fuzzy flexible programming approach for environmental pollution control

    NASA Astrophysics Data System (ADS)

    Lu, H. W.; Huang, G. H.; Maqsood, I.

    2010-12-01

    Optimization techniques have been widely applied to solving environmental management problems, particularly for regional air quality management systems where potential air pollutions arising from improper management would seriously threaten human health. An inexact fuzzy flexible programming approach is developed to facilitate decision support for air quality management. It can tackle both stipulation uncertainty and parameter uncertainty in the objective function and constraints. Upon the previous research efforts, the most significant improvement of this approach is the introduction of multiple control variables corresponding to the objective function and all constraints. This attempt makes it possible for the constraints to be relaxed under respective levels, such that a more satisfactory objective value may be obtained. The impact of each constraint on the system outputs can also be further interpreted. The proposed approach would be helpful for such systems where the decision makers prefer to not only find out an air pollution control scheme with a satisfaction level as high as possible, but also mitigate the uncertainty in decision making. A regional air pollution control problem is then studied to demonstrate the applicability of the developed approach. A variety of management strategies for air pollutants allocation and treatment are suggested in terms of the optimal solutions to decision variables. Comparison between the optimal solutions from the proposed approach and those from a conventional fuzzy flexible programming model is undertaken. It can be found that neither the management strategies nor the priorities of pollutants allocation obtained from the two models are the same. The satisfaction level of the proposed approach (taking the average value of optimized solutions of control variables for comparison) is always higher than that of the existing approach, indicating the superiority of the proposed approach in handling many air pollution control

  14. Development of Advanced Casing Treatments for Flow Control

    NASA Technical Reports Server (NTRS)

    Keith, Theo G., Jr.; Tsung, Fu-Lin

    2001-01-01

    Under the Base R&T and Ultra Efficient Engine Technology programs, the NASA-Goddard Space Flight Center Compressor Branch is investigating flow control strategies required to increase the loading and efficiency of core compressors while maintaining current levels of operability. Flow-control strategies being studied include advanced casing treatments, wall jet injection, and blade-tip injection for compressor stability enhancement, directed jets for surface boundary layer control, and vortex-generating devices. The use of computational fluid dynamics (CFD) simulations to assess the effectiveness of flow-control devices and to guide their design is a key element in this research. CFD simulations serve to screen potential flow-control concepts at a lower cost than executing physical experiments in turbomachinery facilities. CFD simulations also provide guidance in designing physical experiments for those flow control concepts, which appear promising.

  15. Advanced CO2 removal process control and monitor instrumentation development

    NASA Technical Reports Server (NTRS)

    Heppner, D. B.; Dalhausen, M. J.; Klimes, R.

    1982-01-01

    A progam to evaluate, design and demonstrate major advances in control and monitor instrumentation was undertaken. A carbon dioxide removal process, one whose maturity level makes it a prime candidate for early flight demonstration was investigated. The instrumentation design incorporates features which are compatible with anticipated flight requirements. Current electronics technology and projected advances are included. In addition, the program established commonality of components for all advanced life support subsystems. It was concluded from the studies and design activities conducted under this program that the next generation of instrumentation will be greatly smaller than the prior one. Not only physical size but weight, power and heat rejection requirements were reduced in the range of 80 to 85% from the former level of research and development instrumentation. Using a microprocessor based computer, a standard computer bus structure and nonvolatile memory, improved fabrication techniques and aerospace packaging this instrumentation will greatly enhance overall reliability and total system availability.

  16. 40 CFR 439.23 - Effluent limitations attainable by the application of the best conventional pollutant control...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... application of the best conventional pollutant control technology (BCT). Except as provided in 40 CFR 125.30... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS...

  17. 40 CFR 439.23 - Effluent limitations attainable by the application of the best conventional pollutant control...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... application of the best conventional pollutant control technology (BCT). Except as provided in 40 CFR 125.30... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS...

  18. Co-control of urban air pollutants and greenhouse gases in Mexico City.

    PubMed

    West, J Jason; Osnaya, Patricia; Laguna, Israel; Martínez, Julia; Fernández, Adrián

    2004-07-01

    This study addresses the synergies of mitigation measures to control urban air pollutant and greenhouse gas (GHG) emissions, in developing integrated "co-control" strategies for Mexico City. First, existing studies of emissions reduction measures--PROAIRE (the air quality plan for Mexico City) and separate GHG studies--are used to construct a harmonized database of options. Second, linear programming (LP) is developed and applied as a decision-support tool to analyze least-cost strategies for meeting co-control targets for multiple pollutants. We estimate that implementing PROAIRE measures as planned will reduce 3.1% of the 2010 metropolitan CO2 emissions, in addition to substantial local air pollutant reductions. Applying the LP, PROAIRE emissions reductions can be met at a 20% lower cost, using only the PROAIRE measures, by adjusting investments toward the more cost-effective measures; lower net costs are possible by including cost-saving GHG mitigation measures, but with increased investment. When CO2 emission reduction targets are added to PROAIRE targets, the most cost-effective solutions use PROAIRE measures for the majority of local pollutant reductions, and GHG measures for additional CO2 control. Because of synergies, the integrated planning of urban-global co-control can be beneficial, but we estimate that for Mexico City these benefits are often small.

  19. Costs and water quality effects of controlling point and nonpoint pollution sources

    SciTech Connect

    Macal, C.M.; Broomfield, B.J.

    1980-01-01

    Costs and water quality effects of controlling point and nonpoint pollution sources are compared for the DuPage River basin in northern Illinois. Costs are estimated for effluent standards for municipal wastewater treatment plants and for the alternative, controlling runoff from nonpoint sources such as streets, agricultural lands, and forests. A dynamic water-quality/hydrology simulation model is used to determine water quality effects of various treatment plant standards and nonpoint-source controls. Costs and water quality data are combined, and the point-source and nonpoint-source plans are compared on a cost-effectiveness basis. Nonpoint-source controls are found to be more cost-effective than stricter control of pollutants from point sources.

  20. Controlling urban air pollution caused by households: uncertainty, prices, and income.

    PubMed

    Chávez, Carlos A; Stranlund, John K; Gómez, Walter

    2011-10-01

    We examine the control of air pollution caused by households burning wood for heating and cooking in the developing world. Since the problem is one of controlling emissions from nonpoint sources, regulations are likely to be directed at household choices of wood consumption and combustion technologies. Moreover, these choices are subtractions from, or contributions to, the pure public good of air quality. Consequently, the efficient policy design is not independent of the distribution of household income. Since it is unrealistic to assume that environmental authorities can make lump sum income transfers part of control policies, efficient control of air pollution caused by wood consumption entails a higher tax on wood consumption and a higher subsidy for more efficient combustion technologies for higher income households. Among other difficulties, implementing a policy to promote the adoption of cleaner combustion technologies must overcome the seemingly paradoxical result that efficient control calls for higher technology subsidies for higher income households.