Science.gov

Sample records for advanced quantum devices

  1. Efficient Multi-Dimensional Simulation of Quantum Confinement Effects in Advanced MOS Devices

    NASA Technical Reports Server (NTRS)

    Biegel, Bryan A.; Ancona, Mario G.; Rafferty, Conor S.; Yu, Zhiping

    2000-01-01

    We investigate the density-gradient (DG) transport model for efficient multi-dimensional simulation of quantum confinement effects in advanced MOS devices. The formulation of the DG model is described as a quantum correction ot the classical drift-diffusion model. Quantum confinement effects are shown to be significant in sub-100nm MOSFETs. In thin-oxide MOS capacitors, quantum effects may reduce gate capacitance by 25% or more. As a result, the inclusion of quantum effects may reduce gate capacitance by 25% or more. As a result, the inclusion of quantum effects in simulations dramatically improves the match between C-V simulations and measurements for oxide thickness down to 2 nm. Significant quantum corrections also occur in the I-V characteristics of short-channel (30 to 100 nm) n-MOSFETs, with current drive reduced by up to 70%. This effect is shown to result from reduced inversion charge due to quantum confinement of electrons in the channel. Also, subthreshold slope is degraded by 15 to 20 mV/decade with the inclusion of quantum effects via the density-gradient model, and short channel effects (in particular, drain-induced barrier lowering) are noticeably increased.

  2. Efficient Multi-Dimensional Simulation of Quantum Confinement Effects in Advanced MOS Devices

    NASA Technical Reports Server (NTRS)

    Biegel, Bryan A.; Rafferty, Conor S.; Ancona, Mario G.; Yu, Zhi-Ping

    2000-01-01

    We investigate the density-gradient (DG) transport model for efficient multi-dimensional simulation of quantum confinement effects in advanced MOS devices. The formulation of the DG model is described as a quantum correction to the classical drift-diffusion model. Quantum confinement effects are shown to be significant in sub-100nm MOSFETs. In thin-oxide MOS capacitors, quantum effects may reduce gate capacitance by 25% or more. As a result, the inclusion or quantum effects in simulations dramatically improves the match between C-V simulations and measurements for oxide thickness down to 2 nm. Significant quantum corrections also occur in the I-V characteristics of short-channel (30 to 100 nm) n-MOSFETs, with current drive reduced by up to 70%. This effect is shown to result from reduced inversion charge due to quantum confinement of electrons in the channel. Also, subthreshold slope is degraded by 15 to 20 mV/decade with the inclusion of quantum effects via the density-gradient model, and short channel effects (in particular, drain-induced barrier lowering) are noticeably increased.

  3. The quantum hydrodynamic model for semiconductor devices

    NASA Astrophysics Data System (ADS)

    Gardner, Carl L.

    1995-02-01

    Quantum semiconductor devices are playing an increasingly important role in advanced microelectronic applications, including multiple-state logic and memory devices. To model quantum devices, the classical hydrodynamic model for semiconductor devices can be extended to include O(h(2)) quantum corrections. This proposal focused on theoretical and computational investigations of the flow of electrons in semiconductor devices based on the quantum hydrodynamic model. The development of efficient, robots numerical methods for the QHD model in one and two spatial dimensions we also emphasized.

  4. Advanced III/V quantum-structure devices for high performance infrared focal plane arrays

    NASA Astrophysics Data System (ADS)

    Rehm, Robert; Walther, Martin; Schmitz, Johannes; Rutz, Frank; Fleissner, Joachim; Scheibner, Ralf; Ziegler, Johann

    2009-09-01

    A mature production technology for Quantum Well Infrared Photodetector (QWIP) focal plane arrays (FPAs) and InAs/GaSb superlattice (SL) FPAs has been developed. Dual-band and dual-color QWIP- and SL-imagers are demonstrated for the 3-5 μm and 8-12 μm atmospheric windows in the infrared. The simultaneous, co-located detection of both spectral channels resolves the temporal and spatial registration problems common to existing bispectral IRimagers. The ability for a reliable remote detection of hot CO2 signatures makes tailored dual-color superlattice imagers ideally suited for missile warning systems for airborne platforms.

  5. Recent advances on integrated quantum communications

    NASA Astrophysics Data System (ADS)

    Orieux, Adeline; Diamanti, Eleni

    2016-08-01

    In recent years, the use of integrated technologies for applications in the field of quantum information processing and communications has made great progress. The resulting devices feature valuable characteristics such as scalability, reproducibility, low cost and interconnectivity, and have the potential to revolutionize our computation and communication practices in the future, much in the way that electronic integrated circuits have drastically transformed our information processing capacities since the last century. Among the multiple applications of integrated quantum technologies, this review will focus on typical components of quantum communication systems and on overall integrated system operation characteristics. We are interested in particular in the use of photonic integration platforms for developing devices necessary in quantum communications, including sources, detectors and both passive and active optical elements. We also illustrate the challenges associated with performing quantum communications on chip, by using the case study of quantum key distribution—the most advanced application of quantum information science. We conclude with promising perspectives in this field.

  6. Advanced Semiconductor Devices

    NASA Astrophysics Data System (ADS)

    Shur, Michael S.; Maki, Paul A.; Kolodzey, James

    2007-06-01

    I. Wide band gap devices. Wide-Bandgap Semiconductor devices for automotive applications / M. Sugimoto ... [et al.]. A GaN on SiC HFET device technology for wireless infrastructure applications / B. Green ... [et al.]. Drift velocity limitation in GaN HEMT channels / A. Matulionis. Simulations of field-plated and recessed gate gallium nitride-based heterojunction field-effect transistors / V. O. Turin, M. S. Shur and D. B. Veksler. Low temperature electroluminescence of green and deep green GaInN/GaN light emitting diodes / Y. Li ... [et al.]. Spatial spectral analysis in high brightness GaInN/GaN light emitting diodes / T. Detchprohm ... [et al.]. Self-induced surface texturing of Al2O3 by means of inductively coupled plasma reactive ion etching in Cl2 chemistry / P. Batoni ... [et al.]. Field and termionic field transport in aluminium gallium arsenide heterojunction barriers / D. V. Morgan and A. Porch. Electrical characteristics and carrier lifetime measurements in high voltage 4H-SiC PiN diodes / P. A. Losee ... [et al.]. Geometry and short channel effects on enhancement-mode n-Channel GaN MOSFETs on p and n- GaN/sapphire substrates / W. Huang, T. Khan and T. P. Chow. 4H-SiC Vertical RESURF Schottky Rectifiers and MOSFETs / Y. Wang, P. A. Losee and T. P. Chow. Present status and future Directions of SiGe HBT technology / M. H. Khater ... [et al.]Optical properties of GaInN/GaN multi-quantum Wells structure and light emitting diode grown by metalorganic chemical vapor phase epitaxy / J. Senawiratne ... [et al.]. Electrical comparison of Ta/Ti/Al/Mo/Au and Ti/Al/Mo/Au Ohmic contacts on undoped GaN HEMTs structure with AlN interlayer / Y. Sun and L. F. Eastman. Above 2 A/mm drain current density of GaN HEMTs grown on sapphire / F. Medjdoub ... [et al.]. Focused thermal beam direct patterning on InGaN during molecular beam epitaxy / X. Chen, W. J. Schaff and L. F. Eastman -- II. Terahertz and millimeter wave devices. Temperature-dependent microwave performance of

  7. Advanced resistive exercise device

    NASA Technical Reports Server (NTRS)

    Raboin, Jasen L. (Inventor); Niebuhr, Jason (Inventor); Cruz, Santana F. (Inventor); Lamoreaux, Christopher D. (Inventor)

    2008-01-01

    The present invention relates to an exercise device, which includes a vacuum cylinder and a flywheel. The flywheel provides an inertial component to the load, which is particularly well suited for use in space as it simulates exercising under normal gravity conditions. Also, the present invention relates to an exercise device, which has a vacuum cylinder and a load adjusting armbase assembly.

  8. Advanced underwater lift device

    NASA Technical Reports Server (NTRS)

    Flanagan, David T.; Hopkins, Robert C.

    1993-01-01

    Flexible underwater lift devices ('lift bags') are used in underwater operations to provide buoyancy to submerged objects. Commercially available designs are heavy, bulky, and awkward to handle, and thus are limited in size and useful lifting capacity. An underwater lift device having less than 20 percent of the bulk and less than 10 percent of the weight of commercially available models was developed. The design features a dual membrane envelope, a nearly homogeneous envelope membrane stress distribution, and a minimum surface-to-volume ratio. A proof-of-concept model of 50 kg capacity was built and tested. Originally designed to provide buoyancy to mock-ups submerged in NASA's weightlessness simulators, the device may have application to water-landed spacecraft which must deploy flotation upon impact, and where launch weight and volume penalties are significant. The device may also be useful for the automated recovery of ocean floor probes or in marine salvage applications.

  9. Nanofabrication for Quantum Devices

    NASA Astrophysics Data System (ADS)

    Kern, D. P.; Lee, K. Y.; Rishton, S. A.; Wind, S. J.

    1992-12-01

    Fabrication of structures for investigation of quantum effects frequently involves the use of MBE/CVD type growth processes to achieve control on an atomic scale in vertical direction and a wide range of combinations of lithography and pattern transfer techniques for control in lateral directions. The challenges ahead lie in the degree of lateral control with which the lithography can be performed, i.e. resolution and placement accuracy, but also in the throughput of the lithography equipment once technological applications are considered. Electron beam resolution can certainly extend to the 1 nm regime, in the case of the STM even to 0.1 nm, appropriate resist materials have to be found, however. Parallelism may be introduced into nanolithography through contact printing with X-rays, electron, ion, or X-ray projection, or arrays of miniaturized scanning electron or ion columns. Pattern transfer relies on a broad spectrum of subtractive and additive processes ranging from wet and dry etching to selective growth techniques. Pattern fidelity and damage to the material are the key issues.

  10. Advances in quantum teleportation

    NASA Astrophysics Data System (ADS)

    Pirandola, S.; Eisert, J.; Weedbrook, C.; Furusawa, A.; Braunstein, S. L.

    2015-10-01

    Quantum teleportation is one of the most important protocols in quantum information. By exploiting the physical resource of entanglement, quantum teleportation serves as a key primitive across a variety of quantum information tasks and represents an important building block for quantum technologies, with a pivotal role in the continuing progress of quantum communication, quantum computing and quantum networks. Here we summarize the basic theoretical ideas behind quantum teleportation and its variant protocols. We focus on the main experiments, together with the technical advantages and disadvantages associated with the use of the various technologies, from photonic qubits and optical modes to atomic ensembles, trapped atoms and solid-state systems. After analysing the current state-of-the-art, we finish by discussing open issues, challenges and potential future implementations.

  11. Relationship between quantum repeating devices and quantum seals

    SciTech Connect

    He Guangping

    2009-07-15

    It is revealed that quantum repeating devices and quantum seals have a very close relationship, thus the theory in one field can be applied to the other. Consequently, it is shown that the fidelity bounds and optimality of quantum repeating devices for decoding quantum information can be violated when they are used for decoding classical information from quantum states and the security bounds for protocols sealing quantum data exist.

  12. Building devices from colloidal quantum dots.

    PubMed

    Kagan, Cherie R; Lifshitz, Efrat; Sargent, Edward H; Talapin, Dmitri V

    2016-08-26

    The continued growth of mobile and interactive computing requires devices manufactured with low-cost processes, compatible with large-area and flexible form factors, and with additional functionality. We review recent advances in the design of electronic and optoelectronic devices that use colloidal semiconductor quantum dots (QDs). The properties of materials assembled of QDs may be tailored not only by the atomic composition but also by the size, shape, and surface functionalization of the individual QDs and by the communication among these QDs. The chemical and physical properties of QD surfaces and the interfaces in QD devices are of particular importance, and these enable the solution-based fabrication of low-cost, large-area, flexible, and functional devices. We discuss challenges that must be addressed in the move to solution-processed functional optoelectronic nanomaterials. PMID:27563099

  13. Silicon superconducting quantum interference device

    SciTech Connect

    Duvauchelle, J. E.; Francheteau, A.; Marcenat, C.; Lefloch, F.; Chiodi, F.; Débarre, D.; Hasselbach, K.; Kirtley, J. R.

    2015-08-17

    We have studied a Superconducting Quantum Interference Device (SQUID) made from a single layer thin film of superconducting silicon. The superconducting layer is obtained by heavily doping a silicon wafer with boron atoms using the gas immersion laser doping technique. The SQUID is composed of two nano-bridges (Dayem bridges) in a loop and shows magnetic flux modulation at low temperature and low magnetic field. The overall behavior shows very good agreement with numerical simulations based on the Ginzburg-Landau equations.

  14. Advanced Modeling of Micromirror Devices

    NASA Technical Reports Server (NTRS)

    Michalicek, M. Adrian; Sene, Darren E.; Bright, Victor M.

    1995-01-01

    The flexure-beam micromirror device (FBMD) is a phase only piston style spatial light modulator demonstrating properties which can be used for phase adaptive corrective optics. This paper presents a complete study of a square FBMD, from advanced model development through final device testing and model verification. The model relates the electrical and mechanical properties of the device by equating the electrostatic force of a parallel-plate capacitor with the counter-acting spring force of the device's support flexures. The capacitor solution is derived via the Schwartz-Christoffel transformation such that the final solution accounts for non-ideal electric fields. The complete model describes the behavior of any piston-style device, given its design geometry and material properties. It includes operational parameters such as drive frequency and temperature, as well as fringing effects, mirror surface deformations, and cross-talk from neighboring devices. The steps taken to develop this model can be applied to other micromirrors, such as the cantilever and torsion-beam designs, to produce an advanced model for any given device. The micromirror devices studied in this paper were commercially fabricated in a surface micromachining process. A microscope-based laser interferometer is used to test the device in which a beam reflected from the device modulates a fixed reference beam. The mirror displacement is determined from the relative phase which generates a continuous set of data for each selected position on the mirror surface. Plots of this data describe the localized deflection as a function of drive voltage.

  15. Carbon Nanotubes Based Quantum Devices

    NASA Technical Reports Server (NTRS)

    Lu, Jian-Ping

    1999-01-01

    This document represents the final report for the NASA cooperative agreement which studied the application of carbon nanotubes. The accomplishments are reviewed: (1) Wrote a review article on carbon nanotubes and its potentials for applications in nanoscale quantum devices. (2) Extensive studies on the effects of structure deformation on nanotube electronic structure and energy band gaps. (3) Calculated the vibrational spectrum of nanotube rope and the effect of pressure. and (4) Investigate the properties of Li intercalated nanotube ropes and explore their potential for energy storage materials and battery applications. These studies have lead to four publications and seven abstracts in international conferences.

  16. Photoelectric devices with quantum coherence

    NASA Astrophysics Data System (ADS)

    Shanhe, Su

    A phtotoelectric device consisting of a three-level system contacted with two fermionic baths and a photon bath is built. Making the Born-Markov approximation, the equation of motion for the density operator in a Lindblad-like form is derived. We obtain the coherence and the efficiency of the system under the steady-state condition. Results show that quantum coherence can enhance the photoelectric conversion efficiency. The efficiency at maximum power can be larger than the CA efficiency bound with the existence of coherence.

  17. Graphene Superconducting Quantum Interference Device

    NASA Astrophysics Data System (ADS)

    Girit, Çaǧlar; Bouchiat, Vincent; Naaman, Ofer; Zhang, Yuanbo; Crommie, Michael; Zettl, Alex; Siddiqi, Irfan

    2010-03-01

    Graphene can support Cooper pair transport when contacted with two superconducting electrodes, resulting in the well-known Josephson effect. By depositing aluminum/palladium electrodes in the geometry of a loop onto a single graphene sheet, we fabricate a two junction dc superconducting quantum interference device (SQUID). Not only an the supercurrent in this device be increased by moving the electrostatic gate away from the Dirac point, but it can also be modulated periodically by an applied magnetic field---a potentially powerful probe of electronic transport in graphene. We analyze the magnetic field modulation of the critical current with the asymmetric/inductive SQUID model of Fulton and Dynes and discuss the variation of the fitting parameters with gate voltage.

  18. Beyond Moore's law: towards competitive quantum devices

    NASA Astrophysics Data System (ADS)

    Troyer, Matthias

    2015-05-01

    A century after the invention of quantum theory and fifty years after Bell's inequality we see the first quantum devices emerge as products that aim to be competitive with the best classical computing devices. While a universal quantum computer of non-trivial size is still out of reach there exist a number commercial and experimental devices: quantum random number generators, quantum simulators and quantum annealers. In this colloquium I will present some of these devices and validation tests we performed on them. Quantum random number generators use the inherent randomness in quantum measurements to produce true random numbers, unlike classical pseudorandom number generators which are inherently deterministic. Optical lattice emulators use ultracold atomic gases in optical lattices to mimic typical models of condensed matter physics. In my talk I will focus especially on the devices built by Canadian company D-Wave systems, which are special purpose quantum simulators for solving hard classical optimization problems. I will review the controversy around the quantum nature of these devices and will compare them to state of the art classical algorithms. I will end with an outlook towards universal quantum computing and end with the question: which important problems that are intractable even for post-exa-scale classical computers could we expect to solve once we have a universal quantum computer?

  19. Individual carbon nanotubes for quantum electronic and quantum photonic devices

    NASA Astrophysics Data System (ADS)

    Ai, Nan

    2011-12-01

    Carbon nanotubes (CNTs) are promising materials since their unique one dimensional geometry leads to remarkable physical properties such as ballistic transport, long mean free path, large direct band gaps, high mechanical tensile strength and strong exciton binding energies, which make them attractive candidates for applications in high-performance nanoelectronics and nanophotonics. CNT-based field-effect transistors (CNT-FETs) are considered to be ideally suited for future nanoelectronics. Single CNT-FETs made by depositing metal electrodes on top of individual CNTs with E-beam lithography have achieved great performance but are limited for massive large area integrated circuit fabrication. Therefore, this thesis demonstrates characteristics of CNT-FETs made by registered in-plane growth utilizing tailored nanoscale catalyst patterns and chemical vapor deposition (CVD), resulting in CNT arrays directly bridging source and drain. The demonstrated access to individual CNTs with pronounced semiconducting behavior opens also the possibility to form more advanced nanoelectronic structures such as CNT quantum dots. CNT-based single electron transistors (CNT-SETS) are promising for quantum electronic devices operating with ultra-low power consumption and allow fundamental studies of electron transport. In addition to existing CNT-SETS based on individual CNTs, we have fabricated the first CNT-SETS based on in-plane grown CNTs using the CVD technique. The demonstrated utilization of registered in-plane growth opens possibilities to create novel SET device geometries which are more complex, i.e. laterally ordered and scalable, as required for advanced quantum electronic devices. Blinking and spectral diffusion are hallmarks of nanoscale light emitters and a challenge for creating stable fluorescent biomarkers or efficient nonclassical light sources. The studies of blinking of CNTs are still in the explorative stage. In this thesis, I show the first experimental

  20. Completely device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Aguilar, Edgar A.; Ramanathan, Ravishankar; Kofler, Johannes; Pawłowski, Marcin

    2016-08-01

    Quantum key distribution (QKD) is a provably secure way for two distant parties to establish a common secret key, which then can be used in a classical cryptographic scheme. Using quantum entanglement, one can reduce the necessary assumptions that the parties have to make about their devices, giving rise to device-independent QKD (DIQKD). However, in all existing protocols to date the parties need to have an initial (at least partially) random seed as a resource. In this work, we show that this requirement can be dropped. Using recent advances in the fields of randomness amplification and randomness expansion, we demonstrate that it is sufficient for the message the parties want to communicate to be (partially) unknown to the adversaries—an assumption without which any type of cryptography would be pointless to begin with. One party can use her secret message to locally generate a secret sequence of bits, which can then be openly used by herself and the other party in a DIQKD protocol. Hence our work reduces the requirements needed to perform secure DIQKD and establish safe communication.

  1. Fully device-independent quantum key distribution.

    PubMed

    Vazirani, Umesh; Vidick, Thomas

    2014-10-01

    Quantum cryptography promises levels of security that are impossible to replicate in a classical world. Can this security be guaranteed even when the quantum devices on which the protocol relies are untrusted? This central question dates back to the early 1990s when the challenge of achieving device-independent quantum key distribution was first formulated. We answer this challenge by rigorously proving the device-independent security of a slight variant of Ekert's original entanglement-based protocol against the most general (coherent) attacks. The resulting protocol is robust: While assuming only that the devices can be modeled by the laws of quantum mechanics and are spatially isolated from each other and from any adversary's laboratory, it achieves a linear key rate and tolerates a constant noise rate in the devices. In particular, the devices may have quantum memory and share arbitrary quantum correlations with the eavesdropper. The proof of security is based on a new quantitative understanding of the monogamous nature of quantum correlations in the context of a multiparty protocol. PMID:25325625

  2. A quantum optical firewall based on simple quantum devices

    NASA Astrophysics Data System (ADS)

    Amellal, H.; Meslouhi, A.; Hassouni, Y.; El Baz, M.

    2015-07-01

    In order to enhance the transmission security in quantum communications via coherent states, we propose a quantum optical firewall device to protect a quantum cryptosystem against eavesdropping through optical attack strategies. Similar to the classical model of the firewall, the proposed device gives legitimate users the possibility of filtering, controlling (input/output states) and making a decision (access or deny) concerning the traveling states. To prove the security and efficiency of the suggested optical firewall, we analyze its performances against the family of intercept and resend attacks, especially against one of the most prominent attack schemes known as "Faked State Attack."

  3. Superconducting quantum-interference devices

    NASA Technical Reports Server (NTRS)

    Peters, P. N.; Holdeman, L. B.

    1975-01-01

    Published document discusses devices which are based on weak-link Josephson elements that join superconductors. Links can take numerous forms, and circuitry utilizing links can perform many varied functions with unprecedented sensitivity. Theoretical review of Josephson's junctions include tunneling junctions, point contact devices, microbridges, and proximity-effect devices.

  4. ZnCdMgSe as a Materials Platform for Advanced Photonic Devices: Broadband Quantum Cascade Detectors and Green Semiconductor Disk Lasers

    NASA Astrophysics Data System (ADS)

    De Jesus, Joel

    The ZnCdMgSe family of II-VI materials has unique and promising characteristics that may be useful in practical applications. For example they can be grown lattice matched to InP substrates with lattice matched bandgaps that span from 2.1 to 3.5 eV, they can be successfully doped n-type, have a large conduction band offset (CBO) with no intervalley scattering present when strained, they have lower average phonon energies, and the InP lattice constant lies in the middle of the ZnSe and CdSe binaries compounds giving room to experiment with tensile and compressive stress. However they have not been studied in detail for use in practical devices. Here we have identified two types of devices that are being currently developed that benefit from the ZnCdMgSe-based material properties. These are the intersubband (ISB) quantum cascade (QC) detectors and optically pumped semiconductor lasers that emit in the visible range. The paucity for semiconductor lasers operating in the green-orange portion of the visible spectrum can be easily overcome with the ZnCdMgSe materials system developed in our research. The non-strain limited, large CBO available allows to expand the operating wavelength of ISB devices providing shorter and longer wavelengths than the currently commercially available devices. This property can also be exploited to develop broadband room temperature operation ISB detectors. The work presented here focused first on using the ZnCdMgSe-based material properties and parameter to understand and predict the interband and intersubband transitions of its heterostructures. We did this by studying an active region of a QC device by contactless electroreflectance, photoluminescence, FTIR transmittance and correlating the measurements to the quantum well structure by transfer matrix modeling. Then we worked on optimizing the ZnCdMgSe material heterostructures quality by studying the effects of growth interruptions on their optical and optoelectronic properties of

  5. Measurement-device-independent quantum key distribution.

    PubMed

    Lo, Hoi-Kwong; Curty, Marcos; Qi, Bing

    2012-03-30

    How to remove detector side channel attacks has been a notoriously hard problem in quantum cryptography. Here, we propose a simple solution to this problem--measurement-device-independent quantum key distribution (QKD). It not only removes all detector side channels, but also doubles the secure distance with conventional lasers. Our proposal can be implemented with standard optical components with low detection efficiency and highly lossy channels. In contrast to the previous solution of full device independent QKD, the realization of our idea does not require detectors of near unity detection efficiency in combination with a qubit amplifier (based on teleportation) or a quantum nondemolition measurement of the number of photons in a pulse. Furthermore, its key generation rate is many orders of magnitude higher than that based on full device independent QKD. The results show that long-distance quantum cryptography over say 200 km will remain secure even with seriously flawed detectors. PMID:22540686

  6. Semiconductor quantum wells: old technology or new device functionalities

    NASA Astrophysics Data System (ADS)

    Kolbas, R. M.; Lo, Y. C.; Hsieh, K. Y.; Lee, J. H.; Reed, F. E.; Zhang, D.; Zhang, T.

    2009-08-01

    The introduction of semiconductor quantum wells in the 1970s created a revolution in optoelectronic devices. A large fraction of today's lasers and light emitting diodes are based on quantum wells. It has been more than 30 years but novel ideas and new device functions have recently been demonstrated using quantum well heterostructures. This paper provides a brief overview of the subject and then focuses on the physics of quantum wells that the lead author believes holds the key to new device functionalities. The data and figures contained within are not new. They have been assembled from 30 years of work. They are presented to convey the story of why quantum wells continue to fuel the engine that drives the semiconductor optoelectronic business. My apologies in advance to my students and co-workers that contributed so much that could not be covered in such a short manuscript. The explanations provided are based on the simplest models possible rather than the very sophisticated mathematical models that have evolved over many years. The intended readers are those involved with semiconductor optoelectronic devices and are interested in new device possibilities.

  7. Quantum key distribution based on quantum dimension and independent devices

    NASA Astrophysics Data System (ADS)

    Li, Hong-Wei; Yin, Zhen-Qiang; Chen, Wei; Wang, Shuang; Guo, Guang-Can; Han, Zheng-Fu

    2014-03-01

    In this paper, we propose a quantum key distribution (QKD) protocol based on only a two-dimensional Hilbert space encoding a quantum system and independent devices between the equipment for state preparation and measurement. Our protocol is inspired by the fully device-independent quantum key distribution (FDI-QKD) protocol and the measurement-device-independent quantum key distribution (MDI-QKD) protocol. Our protocol only requires the state to be prepared in the two-dimensional Hilbert space, which weakens the state preparation assumption in the original MDI-QKD protocol. More interestingly, our protocol can overcome the detection loophole problem in the FDI-QKD protocol, which greatly limits the application of FDI-QKD. Hence our protocol can be implemented with practical optical components.

  8. Diamond Quantum Devices in Biology.

    PubMed

    Wu, Yuzhou; Jelezko, Fedor; Plenio, Martin B; Weil, Tanja

    2016-06-01

    The currently available techniques for molecular imaging capable of reaching atomic resolution are limited to low temperatures, vacuum conditions, or large amounts of sample. Quantum sensors based on the spin-dependent photoluminescence of nitrogen-vacancy (NV) centers in diamond offer great potential to achieve single-molecule detection with atomic resolution under ambient conditions. Diamond nanoparticles could also be prepared with implanted NV centers, thereby generating unique nanosensors that are able to traffic into living biological systems. Therefore, this technique might provide unprecedented access and insight into the structure and function of individual biomolecules under physiological conditions as well as observation of biological processes down to the quantum level with atomic resolution. The theory of diamond quantum sensors and the current developments from their preparation to sensing techniques have been critically discussed in this Minireview. PMID:27120692

  9. The quantum-effect device: Tomorrow's transistors

    SciTech Connect

    Bate, R.T.

    1988-03-01

    There are limits on the size and number of circuit elements that can be packed on a computer chip. One is the wave behavior of electrons, which can interfere with performance in the smallest of devices. Physicists are not turning that behavior to their advantage in a new kind of component that depends on electron waves for its operation. With the so called quantum semiconductor device, it will be possible to put the circuitry of a supercomputer on a single chip. The structures for quantum devices have already been made using the same materials as today's chips. Because they can be about 100 times smaller than the devices in present-day integrated circuits, designing and fabricating a viable device presents a formidable challenge. Manufacturing processes will have to become considerably more sophisticated, and new strategies for interconnection and architecture will have to be devised to cope with the special problems of size reduction. 5 figs.

  10. Quantum Heat Engines and Refrigerators: Continuous Devices

    NASA Astrophysics Data System (ADS)

    Kosloff, Ronnie; Levy, Amikam

    2014-04-01

    Quantum thermodynamics supplies a consistent description of quantum heat engines and refrigerators up to a single few-level system coupled to the environment. Once the environment is split into three (a hot, cold, and work reservoir), a heat engine can operate. The device converts the positive gain into power, with the gain obtained from population inversion between the components of the device. Reversing the operation transforms the device into a quantum refrigerator. The quantum tricycle, a device connected by three external leads to three heat reservoirs, is used as a template for engines and refrigerators. The equation of motion for the heat currents and power can be derived from first principles. Only a global description of the coupling of the device to the reservoirs is consistent with the first and second laws of thermodynamics. Optimization of the devices leads to a balanced set of parameters in which the couplings to the three reservoirs are of the same order and the external driving field is in resonance. When analyzing refrigerators, one needs to devote special attention to a dynamical version of the third law of thermodynamics. Bounds on the rate of cooling when Tc→0 are obtained by optimizing the cooling current. All refrigerators as Tc→0 show universal behavior. The dynamical version of the third law imposes restrictions on the scaling as Tc→0 of the relaxation rate γc and heat capacity cV of the cold bath.

  11. Quantum heat engines and refrigerators: continuous devices.

    PubMed

    Kosloff, Ronnie; Levy, Amikam

    2014-01-01

    Quantum thermodynamics supplies a consistent description of quantum heat engines and refrigerators up to a single few-level system coupled to the environment. Once the environment is split into three (a hot, cold, and work reservoir), a heat engine can operate. The device converts the positive gain into power, with the gain obtained from population inversion between the components of the device. Reversing the operation transforms the device into a quantum refrigerator. The quantum tricycle, a device connected by three external leads to three heat reservoirs, is used as a template for engines and refrigerators. The equation of motion for the heat currents and power can be derived from first principles. Only a global description of the coupling of the device to the reservoirs is consistent with the first and second laws of thermodynamics. Optimization of the devices leads to a balanced set of parameters in which the couplings to the three reservoirs are of the same order and the external driving field is in resonance. When analyzing refrigerators, one needs to devote special attention to a dynamical version of the third law of thermodynamics. Bounds on the rate of cooling when Tc→0 are obtained by optimizing the cooling current. All refrigerators as Tc→0 show universal behavior. The dynamical version of the third law imposes restrictions on the scaling as Tc→0 of the relaxation rate γc and heat capacity cV of the cold bath. PMID:24689798

  12. Practical characterization of quantum devices without tomography.

    PubMed

    da Silva, Marcus P; Landon-Cardinal, Olivier; Poulin, David

    2011-11-18

    Quantum tomography is the main method used to assess the quality of quantum information processing devices. However, the amount of resources needed for quantum tomography is exponential in the device size. Part of the problem is that tomography generates much more information than is usually sought. Taking a more targeted approach, we develop schemes that enable (i) estimating the fidelity of an experiment to a theoretical ideal description, (ii) learning which description within a reduced subset best matches the experimental data. Both these approaches yield a significant reduction in resources compared to tomography. In particular, we demonstrate that fidelity can be estimated from a number of simple experiments that is independent of the system size, removing an important roadblock for the experimental study of larger quantum information processing units. PMID:22181862

  13. Photovoltaic and thermophotovoltaic devices with quantum barriers

    DOEpatents

    Wernsman, Bernard R.

    2007-04-10

    A photovoltaic or thermophotovoltaic device includes a diode formed by p-type material and n-type material joined at a p-n junction and including a depletion region adjacent to said p-n junction, and a quantum barrier disposed near or in the depletion region of the p-n junction so as to decrease device reverse saturation current density while maintaining device short circuit current density. In one embodiment, the quantum barrier is disposed on the n-type material side of the p-n junction and decreases the reverse saturation current density due to electrons while in another, the barrier is disposed on the p-type material side of the p-n junction and decreases the reverse saturation current density due to holes. In another embodiment, both types of quantum barriers are used.

  14. Device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Hänggi, Esther

    2010-12-01

    In this thesis, we study two approaches to achieve device-independent quantum key distribution: in the first approach, the adversary can distribute any system to the honest parties that cannot be used to communicate between the three of them, i.e., it must be non-signalling. In the second approach, we limit the adversary to strategies which can be implemented using quantum physics. For both approaches, we show how device-independent quantum key distribution can be achieved when imposing an additional condition. In the non-signalling case this additional requirement is that communication is impossible between all pairwise subsystems of the honest parties, while, in the quantum case, we demand that measurements on different subsystems must commute. We give a generic security proof for device-independent quantum key distribution in these cases and apply it to an existing quantum key distribution protocol, thus proving its security even in this setting. We also show that, without any additional such restriction there always exists a successful joint attack by a non-signalling adversary.

  15. Advancing colloidal quantum dot photovoltaic technology

    NASA Astrophysics Data System (ADS)

    Cheng, Yan; Arinze, Ebuka S.; Palmquist, Nathan; Thon, Susanna M.

    2016-06-01

    Colloidal quantum dots (CQDs) are attractive materials for solar cells due to their low cost, ease of fabrication and spectral tunability. Progress in CQD photovoltaic technology over the past decade has resulted in power conversion efficiencies approaching 10%. In this review, we give an overview of this progress, and discuss limiting mechanisms and paths for future improvement in CQD solar cell technology.We briefly summarize nanoparticle synthesis and film processing methods and evaluate the optoelectronic properties of CQD films, including the crucial role that surface ligands play in materials performance. We give an overview of device architecture engineering in CQD solar cells. The compromise between carrier extraction and photon absorption in CQD photovoltaics is analyzed along with different strategies for overcoming this trade-off. We then focus on recent advances in absorption enhancement through innovative device design and the use of nanophotonics. Several light-trapping schemes, which have resulted in large increases in cell photocurrent, are described in detail. In particular, integrating plasmonic elements into CQD devices has emerged as a promising approach to enhance photon absorption through both near-field coupling and far-field scattering effects. We also discuss strategies for overcoming the single junction efficiency limits in CQD solar cells, including tandem architectures, multiple exciton generation and hybrid materials schemes. Finally, we offer a perspective on future directions for the field and the most promising paths for achieving higher device efficiencies.

  16. Microwave Reentrant Cavities for Quantum Devices

    NASA Astrophysics Data System (ADS)

    Carvalho, Natalia C.; Bourhill, Jeremy; Creedon, Daniel; Goryachev, Maxim; Galliou, Serge; Tobar, Michael

    A microwave reentrant cavity is a device able to provide a very sensitive high-Q microwave mode. Its design can be highly advantageous for electromechanical devices and quantum measurements. In this sense, a tuneable device based on a narrow-gap superconducting reentrant cavity is under development. The resonant frequency is able to be fine-tuned over a range larger than 500 MHz at 10 mK with an electrical Q-factor of 105. Such a cavity could possibly accommodate a transmon qubit to control and manipulate its quantum state. We are also working on the investigation of bulk acoustic wave (BAW) resonators in microwave reentrant cavities. BAW resonators offer a promising way to process quantum information through the coupling between microwaves and acoustic phonons. Thus, we are developing a device able to excite phonons through non-linearities and the piezoelectricity of the plano-convex quartz crystal. We will detail our experiments that work towards cooling gram scale phonon resonances to the quantum ground state. Funded by ARC Grant No. CE110001013 (Australia) and National Counsel of Technological and Scientific Development (Brazil).

  17. Thermoelectric Devices Advance Thermal Management

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Thermoelectric (TE) devices heat, cool, and generate electricity when a temperature differential is provided between the two module faces. In cooperation with NASA, Chico, California-based United States Thermoelectric Consortium Inc. (USTC) built a gas emissions analyzer (GEA) for combustion research. The GEA precipitated hydrocarbon particles, preventing contamination that would hinder precise rocket fuel analysis. The USTC research and design team uses patent-pending dimple, pin-fin, microchannel and microjet structures to develop and design heat dissipation devices on the mini-scale level, which not only guarantee high performance of products, but also scale device size from 1 centimeter to 10 centimeters. USTC continues to integrate the benefits of TE devices in its current line of thermal management solutions and has found the accessibility of NASA technical research to be a valuable, sustainable resource that has continued to positively influence its product design and manufacturing

  18. Quantum dot device tunable from single to triple dot system

    SciTech Connect

    Rogge, M. C.; Haug, R. J.; Pierz, K.

    2013-12-04

    We present a lateral quantum dot device which has a tunable number of quantum dots. Depending on easily tunable gate voltages, one, two or three quantum dots are found. They are investigated in transport and charge detection.

  19. Quantum state transfer in double-quantum-well devices

    NASA Technical Reports Server (NTRS)

    Jakumeit, Jurgen; Tutt, Marcel; Pavlidis, Dimitris

    1994-01-01

    A Monte Carlo simulation of double-quantum-well (DQW) devices is presented in view of analyzing the quantum state transfer (QST) effect. Different structures, based on the AlGaAs/GaAs system, were simulated at 77 and 300 K and optimized in terms of electron transfer and device speed. The analysis revealed the dominant role of the impurity scattering for the QST. Different approaches were used for the optimization of QST devices and basic physical limitations were found in the electron transfer between the QWs. The maximum transfer of electrons from a high to a low mobility well was at best 20%. Negative differential resistance is hampered by the almost linear rather than threshold dependent relation of electron transfer on electric field. By optimizing the doping profile the operation frequency limit could be extended to 260 GHz.

  20. Advanced Concepts in Quantum Mechanics

    NASA Astrophysics Data System (ADS)

    Esposito, Giampiero; Marmo, Giuseppe; Miele, Gennaro; Sudarshan, George

    2014-11-01

    Preface; 1. Introduction: the need for a quantum theory; 2. Experimental foundations of quantum theory; 3. Waves and particles; 4. Schrödinger picture, Heisenberg picture and probabilistic aspects; 5. Integrating the equations of motion; 6. Elementary applications: 1-dimensional problems; 7. Elementary applications: multidimensional problems; 8. Coherent states and related formalism; 9. Introduction to spin; 10. Symmetries in quantum mechanics; 11. Approximation methods; 12. Modern pictures of quantum mechanics; 13. Formulations of quantum mechanics and their physical implications; 14. Exam problems; Glossary of geometric concepts; References; Index.

  1. Half adder capabilities of a coupled quantum dot device

    NASA Astrophysics Data System (ADS)

    Pfeffer, P.; Hartmann, F.; Neri, I.; Schade, A.; Emmerling, M.; Kamp, M.; Gammaitoni, L.; Höfling, S.; Worschech, L.

    2016-05-01

    In this paper we demonstrate two realizations of a half adder based on a voltage-rectifying mechanism involving two Coulomb-coupled quantum dots. First, we examine the ranges of operation of the half adder’s individual elements, the AND and XOR gates, for a single rectifying device. It allows a switching between the two gates by a control voltage and thus enables a clocked half adder operation. The logic gates are shown to be reliably operative in a broad noise amplitude range with negligible error probabilities. Subsequently, we study the implementation of the half adder in a combined double-device consisting of two individually tunable rectifiers. We show that this double device allows a simultaneous operation of both relevant gates at once. The presented devices draw their power solely from electronic fluctuations and are therefore an advancement in the field of energy efficient and autonomous electronics.

  2. Half adder capabilities of a coupled quantum dot device.

    PubMed

    Pfeffer, P; Hartmann, F; Neri, I; Schade, A; Emmerling, M; Kamp, M; Gammaitoni, L; Höfling, S; Worschech, L

    2016-05-27

    In this paper we demonstrate two realizations of a half adder based on a voltage-rectifying mechanism involving two Coulomb-coupled quantum dots. First, we examine the ranges of operation of the half adder's individual elements, the AND and XOR gates, for a single rectifying device. It allows a switching between the two gates by a control voltage and thus enables a clocked half adder operation. The logic gates are shown to be reliably operative in a broad noise amplitude range with negligible error probabilities. Subsequently, we study the implementation of the half adder in a combined double-device consisting of two individually tunable rectifiers. We show that this double device allows a simultaneous operation of both relevant gates at once. The presented devices draw their power solely from electronic fluctuations and are therefore an advancement in the field of energy efficient and autonomous electronics. PMID:27079182

  3. Terahertz detection using double quantum well devices

    NASA Astrophysics Data System (ADS)

    Khodier, Majid; Christodoulou, Christos G.; Simmons, Jerry A.

    2001-12-01

    This paper discusses the principle of operation of an electrically tunable THz detector, working around 2.54 THz, integrated with a bowtie antenna. The detection is based on the idea of photon-assisted tunneling (PAT) in a double quantum well (DQW) device. The bowtie antenna is used to collect the THz radiation and feed it to the detector for processing. The Bowtie antenna geometry is integrated with the DQW device to achieve broadband characteristic, easy design, and compatibility with the detector fabrication process. The principle of operation of the detector is introduced first. Then, results of different bowtie antenna layouts are presented and discussed.

  4. Fabrication of a graphene quantum dot device

    NASA Astrophysics Data System (ADS)

    Lee, Jeong Il; Kim, Eunseong

    2014-03-01

    Graphene, which exhibits a massless Dirac-like spectrum for its electrons, has shown impressive properties for nano-electronics applications including a high mobility and a width dependent bandgap. We will report the preliminary report on the transport property of the suspended graphene nano-ribbon(GNR) quantum dot device down to dilution refrigerator temperature. This GNR QD device was fabricated to realize an ideal probe to investigate Kondo physics--a characteristic phenomenon in the physics of strongly correlated electrons. We gratefully acknowledge the financial support by the National Research Foundation of Korea through the Creative Research Initiatives.

  5. Tunable graphene dc superconducting quantum interference device.

    PubMed

    Girit, Caglar; Bouchiat, V; Naaman, O; Zhang, Y; Crommie, M F; Zettl, A; Siddiqi, I

    2009-01-01

    Graphene exhibits unique electrical properties on account of its reduced dimensionality and "relativistic" band structure. When contacted with two superconducting electrodes, graphene can support Cooper pair transport, resulting in the well-known Josephson effect. We report here the fabrication and operation of a two junction dc superconducting quantum interference device (SQUID) formed by a single graphene sheet contacted with aluminum/palladium electrodes in the geometry of a loop. The supercurrent in this device can be modulated not only via an electrostatic gate but also by an applied magnetic fielda potentially powerful probe of electronic transport in graphene and an ultrasensitive platform for nanomagnetometry. PMID:19090696

  6. Superlattice-based quantum devices: from theory to practical applications

    NASA Astrophysics Data System (ADS)

    Razeghi, M.

    2014-07-01

    The concepts of resonant tunneling and superlattices were first developed by Esaki and Tsu. What started with the new physics of the Esaki tunnel diode has matured into nanoscale engineering of semiconductors superlattices to create whole synthetic band structures. While working at Thomson CSF in France, Manijeh Razeghi went on to develop the metal-organic chemical vapor deposition (MOCVD) and molecular beam epitaxy growth of superlattice material as reported in my seminal volumes of The MOCVD Challenge. After years of considerable effort to bring this technology to maturity, we now see the results of this formidable new science in almost every electronic and photonic device that we encounter. Among the most successful triumphs are the type-II superlattice photodetectors and quantum cascade lasers - these technologies have demonstrated the beauty of turning fundamental concepts into practical devices, thanks to advanced growth technologies. This enables us to design and realize compact devices capable of mimicking or even exceeding nature. Using superlattice to pioneer the development of quantum systems is driving the research work at the Center for Quantum Devices.

  7. Functionalized Graphene Nanoroads for Quantum Well Device

    SciTech Connect

    Zhou, Yungang; Yang, Ping; Wang, Zhiguo; Xiao, Hai Yan; Zu, Xiaotao T.; Sun, Xin; Khaleel, Mohammad A.; Gao, Fei

    2011-03-02

    Using density functional theory, a series of calculations of structural and electronic properties of Si-substituted graphene were conducted. Through substituting C atoms by Si atoms on graphene in the present study, we found that the band gap of graphene can be continuously tuned with differently substitutional concentration. To utilize such substitution-induced band gap changes, we proposed a special design to fabricate graphene-based quantum well device.

  8. Simulation of Ultra-Small Electronic Devices: The Classical-Quantum Transition Region

    NASA Technical Reports Server (NTRS)

    Biegel, Bryan A.; Kutler, Paul (Technical Monitor)

    1997-01-01

    Concern is increasing about how quantum effects will impact electronic device operation as down-scaling continues along the SIA Roadmap through 2010. This document describes part of a new semiconductor device modeling (SDM) program at NAS to investigate these concerns by utilizing advanced NAS and third-party numerical computation software to rapidly implement and investigate electronic device models including quantum effects. This SDM project will investigate quantum effects in devices in the classical-quantum transition region, especially sub-0.1 mm MOSFETs. Specific tasks planned for this project include the use of quantum corrections to the classical drift-diffusion and hydrodynamic models of electron transport, arid the use of nominally quantum models including significant scattering.

  9. Improved Thermoelectric Devices: Advanced Semiconductor Materials for Thermoelectric Devices

    SciTech Connect

    2009-12-11

    Broad Funding Opportunity Announcement Project: Phononic Devices is working to recapture waste heat and convert it into usable electric power. To do this, the company is using thermoelectric devices, which are made from advanced semiconductor materials that convert heat into electricity or actively remove heat for refrigeration and cooling purposes. Thermoelectric devices resemble computer chips, and they manage heat by manipulating the direction of electrons at the nanoscale. These devices aren’t new, but they are currently too inefficient and expensive for widespread use. Phononic Devices is using a high-performance, cost-effective thermoelectric design that will improve the device’s efficiency and enable electronics manufacturers to more easily integrate them into their products.

  10. Efficient self-consistent quantum transport simulator for quantum devices

    SciTech Connect

    Gao, X. Mamaluy, D.; Nielsen, E.; Young, R. W.; Lilly, M. P.; Bishop, N. C.; Carroll, M. S.; Muller, R. P.; Shirkhorshidian, A.

    2014-04-07

    We present a self-consistent one-dimensional (1D) quantum transport simulator based on the Contact Block Reduction (CBR) method, aiming for very fast and robust transport simulation of 1D quantum devices. Applying the general CBR approach to 1D open systems results in a set of very simple equations that are derived and given in detail for the first time. The charge self-consistency of the coupled CBR-Poisson equations is achieved by using the predictor-corrector iteration scheme with the optional Anderson acceleration. In addition, we introduce a new way to convert an equilibrium electrostatic barrier potential calculated from an external simulator to an effective doping profile, which is then used by the CBR-Poisson code for transport simulation of the barrier under non-zero biases. The code has been applied to simulate the quantum transport in a double barrier structure and across a tunnel barrier in a silicon double quantum dot. Extremely fast self-consistent 1D simulations of the differential conductance across a tunnel barrier in the quantum dot show better qualitative agreement with experiment than non-self-consistent simulations.

  11. Efficient self-consistent quantum transport simulator for quantum devices

    NASA Astrophysics Data System (ADS)

    Gao, X.; Mamaluy, D.; Nielsen, E.; Young, R. W.; Shirkhorshidian, A.; Lilly, M. P.; Bishop, N. C.; Carroll, M. S.; Muller, R. P.

    2014-04-01

    We present a self-consistent one-dimensional (1D) quantum transport simulator based on the Contact Block Reduction (CBR) method, aiming for very fast and robust transport simulation of 1D quantum devices. Applying the general CBR approach to 1D open systems results in a set of very simple equations that are derived and given in detail for the first time. The charge self-consistency of the coupled CBR-Poisson equations is achieved by using the predictor-corrector iteration scheme with the optional Anderson acceleration. In addition, we introduce a new way to convert an equilibrium electrostatic barrier potential calculated from an external simulator to an effective doping profile, which is then used by the CBR-Poisson code for transport simulation of the barrier under non-zero biases. The code has been applied to simulate the quantum transport in a double barrier structure and across a tunnel barrier in a silicon double quantum dot. Extremely fast self-consistent 1D simulations of the differential conductance across a tunnel barrier in the quantum dot show better qualitative agreement with experiment than non-self-consistent simulations.

  12. Advances in nonlinear optical materials and devices

    NASA Technical Reports Server (NTRS)

    Byer, Robert L.

    1991-01-01

    The recent progress in the application of nonlinear techniques to extend the frequency of laser sources has come from the joint progress in laser sources and in nonlinear materials. A brief summary of the progress in diode pumped solid state lasers is followed by an overview of progress in nonlinear frequency extension by harmonic generation and parametric processes. Improved nonlinear materials including bulk crystals, quasiphasematched interactions, guided wave devices, and quantum well intersubband studies are discussed with the idea of identifying areas of future progress in nonlinear materials and devices.

  13. Quantum chromodynamics with advanced computing

    SciTech Connect

    Kronfeld, Andreas S.; /Fermilab

    2008-07-01

    We survey results in lattice quantum chromodynamics from groups in the USQCD Collaboration. The main focus is on physics, but many aspects of the discussion are aimed at an audience of computational physicists.

  14. Quantum transport in nanoscale semiconductor devices

    NASA Astrophysics Data System (ADS)

    Jones, Gregory Millington

    Because of technological advancement, transistor dimensions are approaching the length scale of the electron Fermi wavelength, on the order of only nanometers. In this regime, quantum mechanical phenomena will dominate electron transport. Using InAs single quantum wells, we have fabricated Y-shaped electron waveguides whose lengths are smaller than the elastic mean free path. Electron transport in these waveguides is ballistic, a quantum mechanical phenomenon. Coupled to the electron waveguide are two gates used to coherently steer the electron wave. We demonstrate for the first time that gating modifies the electron's wave function, by changing its geometrical resonance in the waveguide. Evidence of this alteration is the observation of anti-correlated, oscillatory transconductances. Our data provides direct evidence of wavefunction steering in a transistor structure and has applications in high-speed, low-power electronics. Quantum computing, if realized, will have a significant impact in computer security. The development of quantum computers has been hindered by challenges in producing the basic building block, the qubit. Qubit approaches using semiconductors promise upscalability and can take the form of a single electron transistor. We have designed, fabricated, and characterized single electron transistors in InAs, and separately in silicon, for the application of quantum computing. With the InAs single electron transistor, we have demonstrated one-electron quantum dots using a single-top-gate transistor configuration on a composite quantum well. Electrical transport data indicates a 15meV charging energy and a 20meV orbital energy spacing, which implies a quantum dot of 20nm in diameter. InAs is attractive due to its large electron Lande g-factor. With the silicon-based single electron transistor, we have demonstrated a structure that is similar to conventional silicon-based metal-oxide-semiconductor field effect transistors. The substrate is undoped and

  15. Physics of Quantum Structures in Photovoltaic Devices

    NASA Technical Reports Server (NTRS)

    Raffaelle, Ryne P.; Andersen, John D.

    2005-01-01

    There has been considerable activity recently regarding the possibilities of using various nanostructures and nanomaterials to improve photovoltaic conversion of solar energy. Recent theoretical results indicate that dramatic improvements in device efficiency may be attainable through the use of three-dimensional arrays of zero-dimensional conductors (i.e., quantum dots) in an ordinary p-i-n solar cell structure. Quantum dots and other nanostructured materials may also prove to have some benefits in terms of temperature coefficients and radiation degradation associated with space solar cells. Two-dimensional semiconductor superlattices have already demonstrated some advantages in this regard. It has also recently been demonstrated that semiconducting quantum dots can also be used to improve conversion efficiencies in polymeric thin film solar cells. Improvement in thin film cells utilizing conjugated polymers has also be achieved through the use of one-dimensional quantum structures such as carbon nanotubes. It is believed that carbon nanotubes may contribute to both the disassociation as well as the carrier transport in the conjugated polymers used in certain thin film photovoltaic cells. In this paper we will review the underlying physics governing some of the new photovoltaic nanostructures being pursued, as well as the the current methods being employed to produce III-V, II-VI, and even chalcopyrite-based nanomaterials and nanostructures for solar cells.

  16. Using Quantum Confinement to Uniquely Identify Devices.

    PubMed

    Roberts, J; Bagci, I E; Zawawi, M A M; Sexton, J; Hulbert, N; Noori, Y J; Young, M P; Woodhead, C S; Missous, M; Migliorato, M A; Roedig, U; Young, R J

    2015-01-01

    Modern technology unintentionally provides resources that enable the trust of everyday interactions to be undermined. Some authentication schemes address this issue using devices that give a unique output in response to a challenge. These signatures are generated by hard-to-predict physical responses derived from structural characteristics, which lend themselves to two different architectures, known as unique objects (UNOs) and physically unclonable functions (PUFs). The classical design of UNOs and PUFs limits their size and, in some cases, their security. Here we show that quantum confinement lends itself to the provision of unique identities at the nanoscale, by using fluctuations in tunnelling measurements through quantum wells in resonant tunnelling diodes (RTDs). This provides an uncomplicated measurement of identity without conventional resource limitations whilst providing robust security. The confined energy levels are highly sensitive to the specific nanostructure within each RTD, resulting in a distinct tunnelling spectrum for every device, as they contain a unique and unpredictable structure that is presently impossible to clone. This new class of authentication device operates with minimal resources in simple electronic structures above room temperature. PMID:26553435

  17. Using Quantum Confinement to Uniquely Identify Devices

    NASA Astrophysics Data System (ADS)

    Roberts, J.; Bagci, I. E.; Zawawi, M. A. M.; Sexton, J.; Hulbert, N.; Noori, Y. J.; Young, M. P.; Woodhead, C. S.; Missous, M.; Migliorato, M. A.; Roedig, U.; Young, R. J.

    2015-11-01

    Modern technology unintentionally provides resources that enable the trust of everyday interactions to be undermined. Some authentication schemes address this issue using devices that give a unique output in response to a challenge. These signatures are generated by hard-to-predict physical responses derived from structural characteristics, which lend themselves to two different architectures, known as unique objects (UNOs) and physically unclonable functions (PUFs). The classical design of UNOs and PUFs limits their size and, in some cases, their security. Here we show that quantum confinement lends itself to the provision of unique identities at the nanoscale, by using fluctuations in tunnelling measurements through quantum wells in resonant tunnelling diodes (RTDs). This provides an uncomplicated measurement of identity without conventional resource limitations whilst providing robust security. The confined energy levels are highly sensitive to the specific nanostructure within each RTD, resulting in a distinct tunnelling spectrum for every device, as they contain a unique and unpredictable structure that is presently impossible to clone. This new class of authentication device operates with minimal resources in simple electronic structures above room temperature.

  18. Using Quantum Confinement to Uniquely Identify Devices

    PubMed Central

    Roberts, J.; Bagci, I. E.; Zawawi, M. A. M.; Sexton, J.; Hulbert, N.; Noori, Y. J.; Young, M. P.; Woodhead, C. S.; Missous, M.; Migliorato, M. A.; Roedig, U.; Young, R. J.

    2015-01-01

    Modern technology unintentionally provides resources that enable the trust of everyday interactions to be undermined. Some authentication schemes address this issue using devices that give a unique output in response to a challenge. These signatures are generated by hard-to-predict physical responses derived from structural characteristics, which lend themselves to two different architectures, known as unique objects (UNOs) and physically unclonable functions (PUFs). The classical design of UNOs and PUFs limits their size and, in some cases, their security. Here we show that quantum confinement lends itself to the provision of unique identities at the nanoscale, by using fluctuations in tunnelling measurements through quantum wells in resonant tunnelling diodes (RTDs). This provides an uncomplicated measurement of identity without conventional resource limitations whilst providing robust security. The confined energy levels are highly sensitive to the specific nanostructure within each RTD, resulting in a distinct tunnelling spectrum for every device, as they contain a unique and unpredictable structure that is presently impossible to clone. This new class of authentication device operates with minimal resources in simple electronic structures above room temperature. PMID:26553435

  19. Measurement-device-independent quantum cryptography

    DOE PAGESBeta

    Xu, Feihu; Curty, Marcos; Qi, Bing; Lo, Hoi-Kwong

    2014-12-18

    In theory, quantum key distribution (QKD) provides information-theoretic security based on the laws of physics. Owing to the imperfections of real-life implementations, however, there is a big gap between the theory and practice of QKD, which has been recently exploited by several quantum hacking activities. To fill this gap, a novel approach, called measurement-device-independent QKD (mdiQKD), has been proposed. In addition, it can remove all side-channels from the measurement unit, arguably the most vulnerable part in QKD systems, thus offering a clear avenue toward secure QKD realisations. In this study, we review the latest developments in the framework of mdiQKD,more » together with its assumptions, strengths, and weaknesses.« less

  20. Measurement-device-independent quantum cryptography

    SciTech Connect

    Xu, Feihu; Curty, Marcos; Qi, Bing; Lo, Hoi-Kwong

    2014-12-18

    In theory, quantum key distribution (QKD) provides information-theoretic security based on the laws of physics. Owing to the imperfections of real-life implementations, however, there is a big gap between the theory and practice of QKD, which has been recently exploited by several quantum hacking activities. To fill this gap, a novel approach, called measurement-device-independent QKD (mdiQKD), has been proposed. In addition, it can remove all side-channels from the measurement unit, arguably the most vulnerable part in QKD systems, thus offering a clear avenue toward secure QKD realisations. In this study, we review the latest developments in the framework of mdiQKD, together with its assumptions, strengths, and weaknesses.

  1. Measurement-device-independent quantum coin tossing

    NASA Astrophysics Data System (ADS)

    Zhao, Liangyuan; Yin, Zhenqiang; Wang, Shuang; Chen, Wei; Chen, Hua; Guo, Guangcan; Han, Zhengfu

    2015-12-01

    Quantum coin tossing (QCT) is an important primitive of quantum cryptography and has received continuous interest. However, in practical QCT, Bob's detectors can be subjected to detector-side channel attacks launched by dishonest Alice, which will possibly make the protocol completely insecure. Here, we report a simple strategy of a detector-blinding attack based on a recent experiment. To remove all the detector side channels, we present a solution of measurement-device-independent QCT (MDI-QCT). This method is similar to the idea of MDI quantum key distribution (QKD). MDI-QCT is loss tolerant with single-photon sources and has the same bias as the original loss-tolerant QCT under a coherent attack. Moreover, it provides the potential advantage of doubling the secure distance for some special cases. Finally, MDI-QCT can also be modified to fit the weak coherent-state sources. Thus, based on the rapid development of practical MDI-QKD, our proposal can be implemented easily.

  2. A model of quantum communication device for quantum hashing

    NASA Astrophysics Data System (ADS)

    Vasiliev, A.

    2016-02-01

    In this paper we consider a model of quantum communications between classical computers aided with quantum processors, connected by a classical and a quantum channel. This type of communications implying both classical and quantum messages with moderate use of quantum processing is implicitly used in many quantum protocols, such as quantum key distribution or quantum digital signature. We show that using the model of a quantum processor on multiatomic ensembles in the common QED cavity we can speed up quantum hashing, which can be the basis of quantum digital signature and other communication protocols.

  3. Implementations for device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Máttar, Alejandro; Acín, Antonio

    2016-04-01

    Device-independent quantum key distribution (DIQKD) generates a secret key among two parties in a provably secure way without making assumptions about the internal working of the devices used in the protocol. The main challenge for a DIQKD physical implementation is that the data observed among the two parties must violate a Bell inequality without fair-sampling, since otherwise the observed correlations can be faked with classical resources and security can no longer be guaranteed. In spite of the advances recently made to achieve higher detection efficiencies in Bell experiments, DIQKD remains experimentally difficult at long distances due to the exponential increase of loss in the channel separating the two parties. Here we describe and analyze plausible solutions to overcome the crucial problem of channel loss in the frame of DIQKD physical implementations.

  4. Advanced Electro-Optic Surety Devices

    SciTech Connect

    Watterson, C.E.

    1997-05-01

    The Advanced Electro-Optic Surety Devices project was initiated in march 1991 to support design laboratory guidance on electro-optic device packaging and evaluation. Sandia National Laboratory requested AlliedSignal Inc., Kansas City Division (KCD), to prepare for future packaging efforts in electro-optic integrated circuits. Los Alamos National Laboratory requested the evaluation of electro-optic waveguide devices for nuclear surety applications. New packaging techniques involving multiple fiber optic alignment and attachment, binary lens array development, silicon V-groove etching, and flip chip bonding were requested. Hermetic sealing of the electro-optic hybrid and submicron alignment of optical components present new challenges to be resolved. A 10-channel electro-optic modulator and laser amplifier were evaluated for potential surety applications.

  5. Detector-device-independent quantum key distribution

    SciTech Connect

    Lim, Charles Ci Wen; Korzh, Boris; Martin, Anthony; Bussières, Félix; Thew, Rob; Zbinden, Hugo

    2014-12-01

    Recently, a quantum key distribution (QKD) scheme based on entanglement swapping, called measurement-device-independent QKD (mdiQKD), was proposed to bypass all measurement side-channel attacks. While mdiQKD is conceptually elegant and offers a supreme level of security, the experimental complexity is challenging for practical systems. For instance, it requires interference between two widely separated independent single-photon sources, and the secret key rates are dependent on detecting two photons—one from each source. Here, we demonstrate a proof-of-principle experiment of a QKD scheme that removes the need for a two-photon system and instead uses the idea of a two-qubit single-photon to significantly simplify the implementation and improve the efficiency of mdiQKD in several aspects.

  6. Colloidal quantum dot light-emitting devices.

    PubMed

    Wood, Vanessa; Bulović, Vladimir

    2010-01-01

    Colloidal quantum dot light-emitting devices (QD-LEDs) have generated considerable interest for applications such as thin film displays with improved color saturation and white lighting with a high color rendering index (CRI). We review the key advantages of using quantum dots (QDs) in display and lighting applications, including their color purity, solution processability, and stability. After highlighting the main developments in QD-LED technology in the past 15 years, we describe the three mechanisms for exciting QDs - optical excitation, Förster energy transfer, and direct charge injection - that have been leveraged to create QD-LEDs. We outline the challenges facing QD-LED development, such as QD charging and QD luminescence quenching in QD thin films. We describe how optical downconversion schemes have enabled researchers to overcome these challenges and develop commercial lighting products that incorporate QDs to achieve desirable color temperature and a high CRI while maintaining efficiencies comparable to inorganic white LEDs (>65 lumens per Watt). We conclude by discussing some current directions in QD research that focus on achieving higher efficiency and air-stable QD-LEDs using electrical excitation of the luminescent QDs. PMID:22110863

  7. DSP control of superconducting quantum interference devices

    SciTech Connect

    Bracht, R.R.; Kung, Pang-Jen; Lewis, P.S.; Flynn, E.R.

    1994-08-01

    Superconducting quantum interference devices (SQUIDS) are used to defect very law level magnetic fields. Los Alamos National Laboratory is involved in developing digital signal processing (DSP) based instrumentation for these devices in conjunction with detecting magnetic flux from the human brain. This field of application is known as magnetoencephalography (MEG). The magnetic signals generated by the brain are on the order of a billion times smaller than the earth`s magnetic field, yet they can readily be detected with these highly ,sensitive magnetic detectors. Los Alamos National Laboratory has developed and implemented DSP control of the SQUID system. This has been accomplished by using an AT&T DSP32C DSP in conjunction with dual 18 bit a-to-d and d-to-a converters. The DSP performs the signal demodulation by synchronously sampling the recovered signal and applying the appropriate full wave rectification. The signal is then integrated and filtered and applied to the output. Also, the modulation signal is generated with the DSP system. All of the flux lock loop electronics are replaced except for the low noise analog preamplifier at the front of the recovery components. The system has been tested with both an electronic SQUID simulator and a low temperature thin film SQUID from Conductus. A number of experiments have been performed to allow evaluation of the system improvement made possible by use of DSP control.

  8. Multimode quantum interference of photons in multiport integrated devices

    PubMed Central

    Peruzzo, Alberto; Laing, Anthony; Politi, Alberto; Rudolph, Terry; O'Brien, Jeremy L.

    2011-01-01

    Photonics is a leading approach in realizing future quantum technologies and recently, optical waveguide circuits on silicon chips have demonstrated high levels of miniaturization and performance. Multimode interference (MMI) devices promise a straightforward implementation of compact and robust multiport circuits. Here, we show quantum interference in a 2×2 MMI coupler with visibility of V=95.6±0.9%. We further demonstrate the operation of a 4×4 port MMI device with photon pairs, which exhibits complex quantum interference behaviour. We have developed a new technique to fully characterize such multiport devices, which removes the need for phase-sensitive measurements and may find applications for a wide range of photonic devices. Our results show that MMI devices can operate in the quantum regime with high fidelity and promise substantial simplification and concatenation of photonic quantum circuits. PMID:21364563

  9. Performance of device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Cao, Zhu; Zhao, Qi; Ma, Xiongfeng

    2016-07-01

    Quantum key distribution provides information-theoretically-secure communication. In practice, device imperfections may jeopardise the system security. Device-independent quantum key distribution solves this problem by providing secure keys even when the quantum devices are untrusted and uncharacterized. Following a recent security proof of the device-independent quantum key distribution, we improve the key rate by tightening the parameter choice in the security proof. In practice where the system is lossy, we further improve the key rate by taking into account the loss position information. From our numerical simulation, our method can outperform existing results. Meanwhile, we outline clear experimental requirements for implementing device-independent quantum key distribution. The maximal tolerable error rate is 1.6%, the minimal required transmittance is 97.3%, and the minimal required visibility is 96.8 % .

  10. Advanced Devices for Cryogenic Thermal Management

    NASA Astrophysics Data System (ADS)

    Bugby, D.; Stouffer, C.; Garzon, J.; Beres, M.; Gilchrist, A.

    2006-04-01

    This paper describes six advanced cryogenic thermal management devices/subsystems developed by Swales Aerospace for ground/space-based applications of interest to NASA, DoD, and the commercial sector. The devices/subsystems described herein include the following: (a) a differential thermal expansion cryogenic thermal switch (DTE-CTSW) constructed with high purity aluminum end-pieces and an Ultem support rod for the 6 K Mid-Infrared Instrument (MIRI) on the James Webb Space Telescope (JWST) (b) a quad-redundant DTE-CTSW assembly for the 35 K science instruments (NIRCam, NIRSpec, and FGS) mounted on the JWST Integrated Science Instrument Module (ISIM) (c) a cryogenic diode heat pipe (CDHP) thermal switching system using methane as the working fluid for the 100 K CRISM hyperspectral mapping instrument on the Mars Reconnaissance Orbiter (MRO) and (d) three additional devices/subsystems developed during the AFRL-sponsored CRYOTOOL program, which include a dual DTE-CTSW/dual cryocooler test bed, a miniaturized neon cryogenic loop heat pipe (mini-CLHP), and an across gimbal cryogenic thermal transport system (GCTTS). For the first three devices/subsystems mentioned above, this paper describes key aspects of the development efforts including concept definition, design, fabrication, and testing. For the latter three, this paper provides brief overview descriptions as key details are provided in a related paper.

  11. Advances toward high spectral resolution quantum X-ray calorimetry

    NASA Technical Reports Server (NTRS)

    Moseley, S. H.; Kelley, R. L.; Schoelkopf, R. J.; Szymkowiak, A. E.; Mccammon, D.

    1988-01-01

    Thermal detectors for X-ray spectroscopy combining high spectral resolution and quantum efficiency have been developed. These microcalorimeters measure the energy released in the absorption of a single photon by sensing the rise in temperature of a small absorbing structure. The ultimate energy resolution of such a device is limited by the thermodynamic power fluctuations in the thermal link between the calorimeter and isothermal bath and can in principle be made as low as 1 eV. The performance of a real device is degraded due to noise contributions such as excess 1/f noise in the thermistor and incomplete conversion of energy into phonons. The authors report some recent advances in thermometry, X-ray absorption and thermalization, fabrication techniques, and detector optimization in the presence of noise. These improvements have resulted in a device with a spectral resolution of 17 eV FWHM, measured at 6 keV.

  12. Quantum Monte Carlo Simulation of Tunneling Devices Using Bohm Trajectories

    NASA Astrophysics Data System (ADS)

    Oriols, X.; García-García, J. J.; Martín, F.; Suñé, J.; González, T.; Mateos, J.; Pardo, D.

    1997-11-01

    A generalization of the classical Monte Carlo (MC) device simulation technique is proposed to simultaneously deal with quantum-mechanical phase-coherence effects and scattering interactions in tunneling devices. The proposed method restricts the quantum treatment of transport to the regions of the device where the potential profile significantly changes in distances of the order of the de Broglie wavelength of the carriers (the quantum window). Bohm trajectories associated to time-dependent Gaussian wavepackets are used to simulate the electron transport in the quantum window. Outside this window, the classical ensemble simulation technique is used. Classical and quantum trajectories are smoothly matched at the boundaries of the quantum window according to a criterium of total energy conservation. A simple one-dimensional simulator for resonant tunneling diodes is presented to demonstrate the feasibility of our proposal.

  13. Image stabilization for SWIR advanced optoelectronic device

    NASA Astrophysics Data System (ADS)

    Schiopu, Paul; Manea, Adrian; Cristea, Ionica; Grosu, Neculai; Craciun, Anca-Ileana; Craciun, Alexandru; Granciu, Dana

    2015-02-01

    At long ranges and under low visibility conditions, Advanced Optoelectronic Device provides the signal-to-noise ratio and image quality in the Short-wave Infra-red - SWIR (wavelengths between 1,1 ÷2,5 μm), significantly better than in the near wave infrared - NWIR and visible spectral bands [1,2]. The quality of image is nearly independent of the polarization in the incoming light, but it is influenced by the relative movement between the optical system and the observer (the operators' handshake), and the movement towards the support system (land and air vehicles). All these make it difficult to detect objectives observation in real time. This paper presents some systems enhance which the ability of observation and sighting through the optical systems without the use of the stands, tripods or other means. We have to eliminate the effect of "tremors of the hands" and the vibration in order to allow the use of optical devices by operators on the moving vehicles on land, on aircraft, or on boats, and to provide additional comfort for the user to track the moving object through the optical system, without losing the control in the process of detection and tracking. The practical applications of stabilization image process, in SWIR, are the most advanced part of the optical observation systems available worldwide [3,4,5]. This application has a didactic nature, because it ensures understanding by the students about image stabilization and their participation in research.

  14. Metal microstructures in advanced CMOS devices

    SciTech Connect

    Gignac, L.M.; Rodbell, K.P.

    1996-12-31

    As advanced semiconductor device features shrink, grain boundaries and interfaces become increasingly more important to the properties of thin metal film. With film thickness decreasing to the range of 10 nm and the corresponding features also decreasing to sub-micrometer sizes, interface and grain boundary properties become dominant. In this regime the details of the surface and grain boundaries dictate the interactions between film layers and the subsequent electrical properties. Therefore it is necessary to accurately characterize these materials on the proper length scale in order to first understand and then to improve the device effectiveness. In this talk we will examine the importance of microstructural characterization of thin metal films used in semiconductor devices and show how microstructure can influence the electrical performance. Specifically, we will review Co and Ti silicides for silicon contact and gate conductor applications, Ti/TiN liner films used for adhesion and diffusion barriers in chemical vapor deposited (CVD) tungsten vertical wiring (vias) and Ti/AlCu/Ti-TiN films used as planar interconnect metal lines.

  15. Schmidt-number benchmarks for continuous-variable quantum devices

    NASA Astrophysics Data System (ADS)

    Namiki, Ryo

    2016-05-01

    We present quantum fidelity benchmarks for continuous-variable (CV) quantum devices to outperform quantum channels which can transmit at most k -dimensional coherences for positive integers k . We determine an upper bound of an average fidelity over Gaussian distributed coherent states for quantum channels whose Schmidt class is k . This settles fundamental fidelity steps where the known classical limit and quantum limit correspond to the two end points of k =1 and k =∞ , respectively. It turns out that the average fidelity is useful to verify to what extent an experimental CV gate can transmit a high-dimensional coherence. The result is further extended to be applicable to general quantum operations or stochastic quantum channels. Although the fidelity is often associated with heterodyne measurements in quantum optics, we can also obtain similar criteria based on quadrature deviations determined via homodyne measurements.

  16. A triple quantum dot based nano-electromechanical memory device

    SciTech Connect

    Pozner, R.; Lifshitz, E.; Peskin, U.

    2015-09-14

    Colloidal quantum dots (CQDs) are free-standing nano-structures with chemically tunable electronic properties. This tunability offers intriguing possibilities for nano-electromechanical devices. In this work, we consider a nano-electromechanical nonvolatile memory (NVM) device incorporating a triple quantum dot (TQD) cluster. The device operation is based on a bias induced motion of a floating quantum dot (FQD) located between two bound quantum dots (BQDs). The mechanical motion is used for switching between two stable states, “ON” and “OFF” states, where ligand-mediated effective interdot forces between the BQDs and the FQD serve to hold the FQD in each stable position under zero bias. Considering realistic microscopic parameters, our quantum-classical theoretical treatment of the TQD reveals the characteristics of the NVM.

  17. A triple quantum dot based nano-electromechanical memory device

    NASA Astrophysics Data System (ADS)

    Pozner, R.; Lifshitz, E.; Peskin, U.

    2015-09-01

    Colloidal quantum dots (CQDs) are free-standing nano-structures with chemically tunable electronic properties. This tunability offers intriguing possibilities for nano-electromechanical devices. In this work, we consider a nano-electromechanical nonvolatile memory (NVM) device incorporating a triple quantum dot (TQD) cluster. The device operation is based on a bias induced motion of a floating quantum dot (FQD) located between two bound quantum dots (BQDs). The mechanical motion is used for switching between two stable states, "ON" and "OFF" states, where ligand-mediated effective interdot forces between the BQDs and the FQD serve to hold the FQD in each stable position under zero bias. Considering realistic microscopic parameters, our quantum-classical theoretical treatment of the TQD reveals the characteristics of the NVM.

  18. Advances in superconducting quantum electronic microcircuit fabrication

    NASA Technical Reports Server (NTRS)

    Kirschman, R. K.; Notarys, H. A.; Mercereau, J. E.

    1975-01-01

    Standard microelectronic fabrication techniques have been utilized to produce batch quantities of superconducting quantum electronic devices and circuits. The overall goal is a fabrication technology yielding circuits that are rugged and stable and capable of being fabricated controllably and reproducibly in sizeable quantities. Our progress toward this goal is presented, with primary emphasis on the most recent work, which includes the use of electron-beam lithography and techniques of hybrid microelectronics. Several prototype microcircuits have been successfully fabricated. These microcircuits are formed in a thin-film parent material consisting of layers of superconducting and normal metals, and use proximity-effect structures as the active circuit elements.

  19. Quantum reading of unitary optical devices

    SciTech Connect

    Dall'Arno, Michele; Bisio, Alessandro; D'Ariano, Giacomo Mauro

    2014-12-04

    We address the problem of quantum reading of optical memories, namely the retrieving of classical information stored in the optical properties of a media with minimum energy. We present optimal strategies for ambiguous and unambiguous quantum reading of unitary optical memories, namely when one's task is to minimize the probability of errors in the retrieved information and when perfect retrieving of information is achieved probabilistically, respectively. A comparison of the optimal strategy with coherent probes and homodyne detection shows that the former saves orders of magnitude of energy when achieving the same performances. Experimental proposals for quantum reading which are feasible with present quantum optical technology are reported.

  20. Nano-Bio Quantum Technology for Device-Specific Materials

    NASA Technical Reports Server (NTRS)

    Choi, Sang H.

    2009-01-01

    The areas discussed are still under development: I. Nano structured materials for TE applications a) SiGe and Be.Te; b) Nano particles and nanoshells. II. Quantum technology for optical devices: a) Quantum apertures; b) Smart optical materials; c) Micro spectrometer. III. Bio-template oriented materials: a) Bionanobattery; b) Bio-fuel cells; c) Energetic materials.

  1. The optimization of measurement device independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Gao, Feng; Ma, Hai-Qiang; Jiao, Rong-Zhen

    2016-04-01

    Measurement device independent quantum key distribution (MDI-QKD) is a promising method for realistic quantum communication which could remove all the side-channel attacks from the imperfections of the devices. Here in this study, we theoretically analyzed the performance of the MDI-QKD system. The asymptotic case rate with the increment of the transmission distance at different polarization misalignment, background count rate and intensity is calculated respectively. The result may provide important parameters for practical application of quantum communications.

  2. Low contact resistance in epitaxial graphene devices for quantum metrology

    SciTech Connect

    Yager, Tom E-mail: ywpark@snu.ac.kr; Lartsev, Arseniy; Lara-Avila, Samuel; Kubatkin, Sergey; Cedergren, Karin; Yakimova, Rositsa; Panchal, Vishal; Kazakova, Olga; Tzalenchuk, Alexander; Kim, Kyung Ho; Park, Yung Woo E-mail: ywpark@snu.ac.kr

    2015-08-15

    We investigate Ti/Au contacts to monolayer epitaxial graphene on SiC (0001) for applications in quantum resistance metrology. Using three-terminal measurements in the quantum Hall regime we observed variations in contact resistances ranging from a minimal value of 0.6 Ω up to 11 kΩ. We identify a major source of high-resistance contacts to be due bilayer graphene interruptions to the quantum Hall current, whilst discarding the effects of interface cleanliness and contact geometry for our fabricated devices. Moreover, we experimentally demonstrate methods to improve the reproducibility of low resistance contacts (<10 Ω) suitable for high precision quantum resistance metrology.

  3. Implementing quantum Fourier transform with integrated photonic devices

    NASA Astrophysics Data System (ADS)

    Tabia, Gelo Noel

    2014-03-01

    Many quantum algorithms that exhibit exponential speedup over their classical counterparts employ the quantum Fourier transform, which is used to solve interesting problems such as prime factorization. Meanwhile, nonclassical interference of single photons achieved on integrated platforms holds the promise of achieving large-scale quantum computation with multiport devices. An optical multiport device can be built to realize any quantum circuit as a sequence of unitary operations performed by beam splitters and phase shifters on path-encoded qudits. In this talk, I will present a recursive scheme for implementing quantum Fourier transform with a multimode interference photonic integrated circuit. Research at Perimeter Institute is supported by the Government of Canada through Industry Canada and by the Province of Ontario through the Ministry of Research and Innovation.

  4. Optimization of semiconductor quantum devices by evolutionary search.

    PubMed

    Goldoni, G; Rossi, F

    2000-07-15

    A novel simulation strategy is proposed for searching for semiconductor quantum devices that are optimized with respect to required performances. Based on evolutionary programming, a technique that implements the paradigm of genetic algorithms in more-complex data structures than strings of bits, the proposed algorithm is able to deal with quantum devices with preset nontrivial constraints (e.g., transition energies, geometric requirements). Therefore our approach allows for automatic design, thus avoiding costly by-hand optimizations. We demonstrate the advantages of the proposed algorithm through a relevant and nontrivial application, the optimization of a second-harmonic-generation device working in resonance conditions. PMID:18064261

  5. High Density Memory Based on Quantum Device Technology

    NASA Technical Reports Server (NTRS)

    vanderWagt, Paul; Frazier, Gary; Tang, Hao

    1995-01-01

    We explore the feasibility of ultra-high density memory based on quantum devices. Starting from overall constraints on chip area, power consumption, access speed, and noise margin, we deduce boundaries on single cell parameters such as required operating voltage and standby current. Next, the possible role of quantum devices is examined. Since the most mature quantum device, the resonant tunneling diode (RTD) can easily be integrated vertically, it naturally leads to the issue of 3D integrated memory. We propose a novel method of addressing vertically integrated bistable two-terminal devices, such as resonant tunneling diodes (RTD) and Esaki diodes, that avoids individual physical contacts. The new concept has been demonstrated experimentally in memory cells of field effect transistors (FET's) and stacked RTD's.

  6. Multiplexed charge-locking device for large arrays of quantum devices

    SciTech Connect

    Puddy, R. K. Smith, L. W; Chong, C. H.; Farrer, I.; Griffiths, J. P.; Ritchie, D. A.; Smith, C. G.; Al-Taie, H.; Kelly, M. J.; Pepper, M.

    2015-10-05

    We present a method of forming and controlling large arrays of gate-defined quantum devices. The method uses an on-chip, multiplexed charge-locking system and helps to overcome the restraints imposed by the number of wires available in cryostat measurement systems. The device architecture that we describe here utilises a multiplexer-type scheme to lock charge onto gate electrodes. The design allows access to and control of gates whose total number exceeds that of the available electrical contacts and enables the formation, modulation and measurement of large arrays of quantum devices. We fabricate such devices on n-type GaAs/AlGaAs substrates and investigate the stability of the charge locked on to the gates. Proof-of-concept is shown by measurement of the Coulomb blockade peaks of a single quantum dot formed by a floating gate in the device. The floating gate is seen to drift by approximately one Coulomb oscillation per hour.

  7. Measurement-device-independent entanglement-based quantum key distribution

    NASA Astrophysics Data System (ADS)

    Yang, Xiuqing; Wei, Kejin; Ma, Haiqiang; Sun, Shihai; Liu, Hongwei; Yin, Zhenqiang; Li, Zuohan; Lian, Shibin; Du, Yungang; Wu, Lingan

    2016-05-01

    We present a quantum key distribution protocol in a model in which the legitimate users gather statistics as in the measurement-device-independent entanglement witness to certify the sources and the measurement devices. We show that the task of measurement-device-independent quantum communication can be accomplished based on monogamy of entanglement, and it is fairly loss tolerate including source and detector flaws. We derive a tight bound for collective attacks on the Holevo information between the authorized parties and the eavesdropper. Then with this bound, the final secret key rate with the source flaws can be obtained. The results show that long-distance quantum cryptography over 144 km can be made secure using only standard threshold detectors.

  8. Continuous-variable measurement-device-independent multipartite quantum communication

    NASA Astrophysics Data System (ADS)

    Wu, Yadong; Zhou, Jian; Gong, Xinbao; Guo, Ying; Zhang, Zhi-Ming; He, Guangqiang

    2016-02-01

    A continuous-variable measurement-device-independent multiparty quantum communication protocol is investigated in this paper. Utilizing the distributed continuous-variable Greenberger-Horne-Zeilinger state, this protocol can implement both quantum cryptographic conference and quantum secret sharing. We analyze the security of the protocol against both the entangling cloner attack and the coherent attack. The entangling cloner attack is a practical individual attack, and the coherent attack is the optimal attack Eve can implement. Simulation results show that the coherent attack can greatly reduce the secret key rate. Different kinds of entangled attacks are compared and we finally discuss the optimal coherent attacks.

  9. Quantum computation: algorithms and implementation in quantum dot devices

    NASA Astrophysics Data System (ADS)

    Gamble, John King

    In this thesis, we explore several aspects of both the software and hardware of quantum computation. First, we examine the computational power of multi-particle quantum random walks in terms of distinguishing mathematical graphs. We study both interacting and non-interacting multi-particle walks on strongly regular graphs, proving some limitations on distinguishing powers and presenting extensive numerical evidence indicative of interactions providing more distinguishing power. We then study the recently proposed adiabatic quantum algorithm for Google PageRank, and show that it exhibits power-law scaling for realistic WWW-like graphs. Turning to hardware, we next analyze the thermal physics of two nearby 2D electron gas (2DEG), and show that an analogue of the Coulomb drag effect exists for heat transfer. In some distance and temperature, this heat transfer is more significant than phonon dissipation channels. After that, we study the dephasing of two-electron states in a single silicon quantum dot. Specifically, we consider dephasing due to the electron-phonon coupling and charge noise, separately treating orbital and valley excitations. In an ideal system, dephasing due to charge noise is strongly suppressed due to a vanishing dipole moment. However, introduction of disorder or anharmonicity leads to large effective dipole moments, and hence possibly strong dephasing. Building on this work, we next consider more realistic systems, including structural disorder systems. We present experiment and theory, which demonstrate energy levels that vary with quantum dot translation, implying a structurally disordered system. Finally, we turn to the issues of valley mixing and valley-orbit hybridization, which occurs due to atomic-scale disorder at quantum well interfaces. We develop a new theoretical approach to study these effects, which we name the disorder-expansion technique. We demonstrate that this method successfully reproduces atomistic tight-binding techniques

  10. Diversionary device history and revolutionary advancements.

    SciTech Connect

    Cooper, Paul W.; Grubelich, Mark Charles

    2005-04-01

    Diversionary devices also known as flash bangs or stun grenades were first employed about three decades ago. These devices produce a loud bang accompanied by a brilliant flash of light and are employed to temporarily distract or disorient an adversary by overwhelming their visual and auditory senses in order to gain a tactical advantage. Early devices that where employed had numerous shortcomings. Over time, many of these deficiencies were identified and corrected. This evolutionary process led to today's modern diversionary devices. These present-day conventional diversionary devices have undergone evolutionary changes but operate in the same manner as their predecessors. In order to produce the loud bang and brilliant flash of light, a flash powder mixture, usually a combination of potassium perchlorate and aluminum powder is ignited to produce an explosion. In essence these diversionary devices are small pyrotechnic bombs that produce a high point-source pressure in order to achieve the desired far-field effect. This high point-source pressure can make these devices a hazard to the operator, adversaries and hostages even though they are intended for 'less than lethal' roles. A revolutionary diversionary device has been developed that eliminates this high point-source pressure problem and eliminates the need for the hazardous pyrotechnic flash powder composition. This new diversionary device employs a fuel charge that is expelled and ignited in the atmosphere. This process is similar to a fuel air or thermobaric explosion, except that it is a deflagration, not a detonation, thereby reducing the overpressure hazard. This technology reduces the hazard associated with diversionary devices to all involved with their manufacture, transport and use. An overview of the history of diversionary device development and developments at Sandia National Laboratories will be presented.

  11. Memory Attacks on Device-Independent Quantum Cryptography

    NASA Astrophysics Data System (ADS)

    Barrett, Jonathan; Colbeck, Roger; Kent, Adrian

    2013-01-01

    Device-independent quantum cryptographic schemes aim to guarantee security to users based only on the output statistics of any components used, and without the need to verify their internal functionality. Since this would protect users against untrustworthy or incompetent manufacturers, sabotage, or device degradation, this idea has excited much interest, and many device-independent schemes have been proposed. Here we identify a critical weakness of device-independent protocols that rely on public communication between secure laboratories. Untrusted devices may record their inputs and outputs and reveal information about them via publicly discussed outputs during later runs. Reusing devices thus compromises the security of a protocol and risks leaking secret data. Possible defenses include securely destroying or isolating used devices. However, these are costly and often impractical. We propose other more practical partial defenses as well as a new protocol structure for device-independent quantum key distribution that aims to achieve composable security in the case of two parties using a small number of devices to repeatedly share keys with each other (and no other party).

  12. Memory attacks on device-independent quantum cryptography.

    PubMed

    Barrett, Jonathan; Colbeck, Roger; Kent, Adrian

    2013-01-01

    Device-independent quantum cryptographic schemes aim to guarantee security to users based only on the output statistics of any components used, and without the need to verify their internal functionality. Since this would protect users against untrustworthy or incompetent manufacturers, sabotage, or device degradation, this idea has excited much interest, and many device-independent schemes have been proposed. Here we identify a critical weakness of device-independent protocols that rely on public communication between secure laboratories. Untrusted devices may record their inputs and outputs and reveal information about them via publicly discussed outputs during later runs. Reusing devices thus compromises the security of a protocol and risks leaking secret data. Possible defenses include securely destroying or isolating used devices. However, these are costly and often impractical. We propose other more practical partial defenses as well as a new protocol structure for device-independent quantum key distribution that aims to achieve composable security in the case of two parties using a small number of devices to repeatedly share keys with each other (and no other party). PMID:23383767

  13. Experimental Measurement-Device-Independent Quantum Key Distribution

    NASA Astrophysics Data System (ADS)

    Liu, Yang; Chen, Teng-Yun; Wang, Liu-Jun; Liang, Hao; Shentu, Guo-Liang; Wang, Jian; Cui, Ke; Yin, Hua-Lei; Liu, Nai-Le; Li, Li; Ma, Xiongfeng; Pelc, Jason S.; Fejer, M. M.; Peng, Cheng-Zhi; Zhang, Qiang; Pan, Jian-Wei

    2013-09-01

    Quantum key distribution is proven to offer unconditional security in communication between two remote users with ideal source and detection. Unfortunately, ideal devices never exist in practice and device imperfections have become the targets of various attacks. By developing up-conversion single-photon detectors with high efficiency and low noise, we faithfully demonstrate the measurement-device-independent quantum-key-distribution protocol, which is immune to all hacking strategies on detection. Meanwhile, we employ the decoy-state method to defend attacks on a nonideal source. By assuming a trusted source scenario, our practical system, which generates more than a 25 kbit secure key over a 50 km fiber link, serves as a stepping stone in the quest for unconditionally secure communications with realistic devices.

  14. Experimental measurement-device-independent quantum key distribution.

    PubMed

    Liu, Yang; Chen, Teng-Yun; Wang, Liu-Jun; Liang, Hao; Shentu, Guo-Liang; Wang, Jian; Cui, Ke; Yin, Hua-Lei; Liu, Nai-Le; Li, Li; Ma, Xiongfeng; Pelc, Jason S; Fejer, M M; Peng, Cheng-Zhi; Zhang, Qiang; Pan, Jian-Wei

    2013-09-27

    Quantum key distribution is proven to offer unconditional security in communication between two remote users with ideal source and detection. Unfortunately, ideal devices never exist in practice and device imperfections have become the targets of various attacks. By developing up-conversion single-photon detectors with high efficiency and low noise, we faithfully demonstrate the measurement-device-independent quantum-key-distribution protocol, which is immune to all hacking strategies on detection. Meanwhile, we employ the decoy-state method to defend attacks on a nonideal source. By assuming a trusted source scenario, our practical system, which generates more than a 25 kbit secure key over a 50 km fiber link, serves as a stepping stone in the quest for unconditionally secure communications with realistic devices. PMID:24116758

  15. Optimal Device Independent Quantum Key Distribution

    PubMed Central

    Kamaruddin, S.; Shaari, J. S.

    2016-01-01

    We consider an optimal quantum key distribution setup based on minimal number of measurement bases with binary yields used by parties against an eavesdropper limited only by the no-signaling principle. We note that in general, the maximal key rate can be achieved by determining the optimal tradeoff between measurements that attain the maximal Bell violation and those that maximise the bit correlation between the parties. We show that higher correlation between shared raw keys at the expense of maximal Bell violation provide for better key rates for low channel disturbance. PMID:27485160

  16. Optimal Device Independent Quantum Key Distribution

    NASA Astrophysics Data System (ADS)

    Kamaruddin, S.; Shaari, J. S.

    2016-08-01

    We consider an optimal quantum key distribution setup based on minimal number of measurement bases with binary yields used by parties against an eavesdropper limited only by the no-signaling principle. We note that in general, the maximal key rate can be achieved by determining the optimal tradeoff between measurements that attain the maximal Bell violation and those that maximise the bit correlation between the parties. We show that higher correlation between shared raw keys at the expense of maximal Bell violation provide for better key rates for low channel disturbance.

  17. Optimal Device Independent Quantum Key Distribution.

    PubMed

    Kamaruddin, S; Shaari, J S

    2016-01-01

    We consider an optimal quantum key distribution setup based on minimal number of measurement bases with binary yields used by parties against an eavesdropper limited only by the no-signaling principle. We note that in general, the maximal key rate can be achieved by determining the optimal tradeoff between measurements that attain the maximal Bell violation and those that maximise the bit correlation between the parties. We show that higher correlation between shared raw keys at the expense of maximal Bell violation provide for better key rates for low channel disturbance. PMID:27485160

  18. ARED (Advanced-Resistive Exercise Device) Update

    NASA Technical Reports Server (NTRS)

    Ploutz-Snyder, Lori

    2009-01-01

    This viewgraph presentation describes ARED which is a new hardware exercise device for use on the International Space Station. Astronaut physiological adaptations, muscle parameters, and cardiovascular parameters are also reviewed.

  19. An advanced space rotary power transfer device

    NASA Astrophysics Data System (ADS)

    Jacobson, P. E.

    A new electrical signal and rotary power transfer device has recently evolved from ball-bearing and electrical-transfer technologies. This hybrid device, known as a roll ring, has been tested extensively since the late 1970s and has demonstrated important operational advantages in a wide variety of signal and power transfer configurations. A high power version has been developed and evaluated. This paper describes this latter roll ring configuration. The paper also summarizes test results.

  20. Microfluidic Devices in Advanced Caenorhabditis elegans Research.

    PubMed

    Muthaiyan Shanmugam, Muniesh; Subhra Santra, Tuhin

    2016-01-01

    The study of model organisms is very important in view of their potential for application to human therapeutic uses. One such model organism is the nematode worm, Caenorhabditis elegans. As a nematode, C. elegans have ~65% similarity with human disease genes and, therefore, studies on C. elegans can be translated to human, as well as, C. elegans can be used in the study of different types of parasitic worms that infect other living organisms. In the past decade, many efforts have been undertaken to establish interdisciplinary research collaborations between biologists, physicists and engineers in order to develop microfluidic devices to study the biology of C. elegans. Microfluidic devices with the power to manipulate and detect bio-samples, regents or biomolecules in micro-scale environments can well fulfill the requirement to handle worms under proper laboratory conditions, thereby significantly increasing research productivity and knowledge. The recent development of different kinds of microfluidic devices with ultra-high throughput platforms has enabled researchers to carry out worm population studies. Microfluidic devices primarily comprises of chambers, channels and valves, wherein worms can be cultured, immobilized, imaged, etc. Microfluidic devices have been adapted to study various worm behaviors, including that deepen our understanding of neuromuscular connectivity and functions. This review will provide a clear account of the vital involvement of microfluidic devices in worm biology. PMID:27490525

  1. Device-independent quantum cryptography for continuous variables

    NASA Astrophysics Data System (ADS)

    Marshall, Kevin; Weedbrook, Christian

    2014-10-01

    We present a device-independent quantum cryptography protocol for continuous variables. Our scheme is based on the Gottesman-Kitaev-Preskill encoding scheme whereby a qubit is embedded in the infinite-dimensional space of a quantum harmonic oscillator. The application of discrete-variable device-independent quantum key distribution to this encoding enables a continuous-variable analog. Since the security of this protocol is based on discrete variables we inherit by default security against collective attacks and, under certain memoryless assumptions, coherent attacks. We find that our protocol is valid over the same distances as its discrete-variable counterpart, except that we are able to take advantage of high efficiency commercially available detectors where, for the most part, only homodyne detection is required. This offers the prospect of closing the loopholes associated with Bell inequalities.

  2. Local gate control in carbon nanotube quantum devices

    NASA Astrophysics Data System (ADS)

    Biercuk, Michael Jordan

    This thesis presents transport measurements of carbon nanotube electronic devices operated in the quantum regime. Nanotubes are contacted by source and drain electrodes, and multiple lithographically-patterned electrostatic gates are aligned to each device. Transport measurements of device conductance or current as a function of local gate voltages reveal that local gates couple primarily to the proximal section of the nanotube, hence providing spatially localized control over carrier density along the nanotube length. Further, using several different techniques we are able to produce local depletion regions along the length of a tube. This phenomenon is explored in detail for different contact metals to the nanotube. We utilize local gating techniques to study multiple quantum dots in carbon nanotubes produced both by naturally occurring defects, and by the controlled application of voltages to depletion gates. We study double quantum dots in detail, where transport measurements reveal honeycomb charge stability diagrams. We extract values of energy-level spacings, capacitances, and interaction energies for this system, and demonstrate independent control over all relevant tunneling rates. We report rf-reflectometry measurements of gate-defined carbon nanotube quantum dots with integrated charge sensors. Aluminum rf-SETs are electrostatically coupled to carbon nanotube devices and detect single electron charging phenomena in the Coulomb blockade regime. Simultaneous correlated measurements of single electron charging are made using reflected rf power from the nanotube itself and from the rf-SET on microsecond time scales. We map charge stability diagrams for the nanotube quantum dot via charge sensing, observing Coulomb charging diamonds beyond the first order. Conductance measurements of carbon nanotubes containing gated local depletion regions exhibit plateaus as a function of gate voltage, spaced by approximately 1e2/h, the quantum of conductance for a single

  3. Long-distance measurement-device-independent multiparty quantum communication.

    PubMed

    Fu, Yao; Yin, Hua-Lei; Chen, Teng-Yun; Chen, Zeng-Bing

    2015-03-01

    The Greenberger-Horne-Zeilinger (GHZ) entanglement, originally introduced to uncover the extreme violation of local realism against quantum mechanics, is an important resource for multiparty quantum communication tasks. But the low intensity and fragility of the GHZ entanglement source in current conditions have made the practical applications of these multiparty tasks an experimental challenge. Here we propose a feasible scheme for practically distributing the postselected GHZ entanglement over a distance of more than 100 km for experimentally accessible parameter regimes. Combining the decoy-state and measurement-device-independent protocols for quantum key distribution, we anticipate that our proposal suggests an important avenue for practical multiparty quantum communication. PMID:25793788

  4. Quantum Dot Device Design Optimization for Resonator Coupling

    NASA Astrophysics Data System (ADS)

    King, Cameron; Coppersmith, S. N.; Friesen, Mark

    Coupling a semiconductor quantum dot qubit to a superconducting resonator broadens the possibilities for interqubit communication and potentially allows integration of quantum dots with other qubit systems. The major technological hurdle that must be overcome is reaching the strong coupling limit, where the coupling frequency between the resonator and the qubit is larger than both the qubit decoherence rate and the photon loss rate of the resonator. In this work, we examine optimization of the quantum dot device design. Using the Thomas-Fermi approximation in conjunction with a metallic dot capacitive model, we focus on improving the capacitive coupling between a resonator gate and a quantum dot while decreasing the cross-coupling to nearby dots. Through these simulations, we find that the optimization follows an intuitive geometric relation. This work was supported in part by ARO (W911NF-12-0607), NSF (PHY-1104660), and ONR (N00014-15-1-0029).

  5. Mini array of quantum Hall devices based on epitaxial graphene

    NASA Astrophysics Data System (ADS)

    Novikov, S.; Lebedeva, N.; Hämäläinen, J.; Iisakka, I.; Immonen, P.; Manninen, A. J.; Satrapinski, A.

    2016-05-01

    Series connection of four quantum Hall effect (QHE) devices based on epitaxial graphene films was studied for realization of a quantum resistance standard with an up-scaled value. The tested devices showed quantum Hall plateaux RH,2 at a filling factor v = 2 starting from a relatively low magnetic field (between 4 T and 5 T) when the temperature was 1.5 K. The precision measurements of quantized Hall resistance of four QHE devices connected by triple series connections and external bonding wires were done at B = 7 T and T = 1.5 K using a commercial precision resistance bridge with 50 μA current through the QHE device. The results showed that the deviation of the quantized Hall resistance of the series connection of four graphene-based QHE devices from the expected value of 4×RH,2 = 2 h/e2 was smaller than the relative standard uncertainty of the measurement (<1 × 10-7) limited by the used resistance bridge.

  6. Integrated quantum dot barcode smartphone optical device for wireless multiplexed diagnosis of infected patients.

    PubMed

    Ming, Kevin; Kim, Jisung; Biondi, Mia J; Syed, Abdullah; Chen, Kun; Lam, Albert; Ostrowski, Mario; Rebbapragada, Anu; Feld, Jordan J; Chan, Warren C W

    2015-03-24

    Inorganic nanoparticles are ideal precursors for engineering barcodes for rapidly detecting diseases. Despite advances in the chemical design of these barcodes, they have not advanced to clinical use because they lack sensitivity and are not cost-effective due to requirement of a large read-out system. Here we combined recent advances in quantum dot barcode technology with smartphones and isothermal amplification to engineer a simple and low-cost chip-based wireless multiplex diagnostic device. We characterized the analytical performance of this device and demonstrated that the device is capable of detecting down to 1000 viral genetic copies per milliliter, and this enabled the diagnosis of patients infected with HIV or hepatitis B. More importantly, the barcoding enabled us to detect multiple infectious pathogens simultaneously, in a single test, in less than 1 h. This multiplexing capability of the device enables the diagnosis of infections that are difficult to differentiate clinically due to common symptoms such as a fever or rash. The integration of quantum dot barcoding technology with a smartphone reader provides a capacity for global surveillance of infectious diseases and the potential to accelerate knowledge exchange transfer of emerging or exigent disease threats with healthcare and military organizations in real time. PMID:25661584

  7. Physical characterization of quantum devices from nonlocal correlations

    NASA Astrophysics Data System (ADS)

    Bancal, Jean-Daniel; Navascués, Miguel; Scarani, Valerio; Vértesi, Tamás; Yang, Tzyh Haur

    2015-02-01

    In the device-independent approach to quantum information theory, quantum systems are regarded as black boxes that, given an input (the measurement setting), return an output (the measurement result). These boxes are then treated regardless of their actual internal working. In this paper we develop swap, a theoretical concept that, in combination with the tool of semidefinite methods for the characterization of quantum correlations, allows us to estimate physical properties of the black boxes from the observed measurement statistics. We find that the swap tool provides bounds orders of magnitude better than previously known techniques (e.g., for a Clauser-Horne-Shimony-Holt violation larger than 2.57, swap predicts a singlet fidelity greater than 70 % ). This method also allows us to deal with hitherto intractable cases such as robust device-independent self-testing of nonmaximally entangled two-qutrit states in the Collins-Gisin-Linden-Massar-Popescu scenario (for which Jordan's lemma does not apply) and the device-independent certification of entangled measurements. We further apply the swap method to relate nonlocal correlations to work extraction and quantum dimensionality, hence demonstrating that this tool can be used to study a wide variety of properties relying on the sole knowledge of accessible statistics.

  8. Experimental measurement-device-independent verification of quantum steering

    NASA Astrophysics Data System (ADS)

    Kocsis, Sacha; Hall, Michael J. W.; Bennet, Adam J.; Saunders, Dylan J.; Pryde, Geoff J.

    2015-01-01

    Bell non-locality between distant quantum systems—that is, joint correlations which violate a Bell inequality—can be verified without trusting the measurement devices used, nor those performing the measurements. This leads to unconditionally secure protocols for quantum information tasks such as cryptographic key distribution. However, complete verification of Bell non-locality requires high detection efficiencies, and is not robust to typical transmission losses over long distances. In contrast, quantum or Einstein-Podolsky-Rosen steering, a weaker form of quantum correlation, can be verified for arbitrarily low detection efficiencies and high losses. The cost is that current steering-verification protocols require complete trust in one of the measurement devices and its operator, allowing only one-sided secure key distribution. Here we present measurement-device-independent steering protocols that remove this need for trust, even when Bell non-locality is not present. We experimentally demonstrate this principle for singlet states and states that do not violate a Bell inequality.

  9. Quantum interference in a Cooper pair splitter device

    NASA Astrophysics Data System (ADS)

    Csonka, Szabolcs; Fulop, G.; Dominguez, F.; Levy Yeyati, A.; D'Hollosy, S.; Baumgartner, A.; Makk, P.; Schonenberger, C.; Guzenko, V. A.; Madsen, M. H.; Nygard, J.

    Cooper pair splitting (CPS) is a process in which the electrons of naturally occurring spin singlet pairs in a superconductor are spatially separated using two quantum dots. In the present work we investigate the evolution of the conductance correlations in an InAs nanowire based CPS device in the presence of an external magnetic field. In our experiments the gate dependence of the signal that depends on both quantum dots continuously evolves from a slightly asymmetric Lorentzian to a strongly asymmetric Fano-type resonance with increasing B field. Our experiments can be understood in a simple 3 site model, which shows that the nonlocal CPS leads to symmetric line shapes, while the local transport processes can exhibit an asymmetric shape due to quantum interference. These findings demonstrate that the electrons from a Cooper pair splitter can propagate coherently after their emission from the superconductor and how a magnetic field can be used to optimize the performance of a CPS device. In addition CPS devices were developed where the nanowire segments between the two dots were removed, nonlocal measurement on such CPS devices will also be presented.

  10. Quantum fluctuation theorem in an interacting setup: point contacts in fractional quantum Hall edge state devices.

    PubMed

    Komnik, A; Saleur, H

    2011-09-01

    We verify the validity of the Cohen-Gallavotti fluctuation theorem for the strongly correlated problem of charge transfer through an impurity in a chiral Luttinger liquid, which is realizable experimentally as a quantum point contact in a fractional quantum Hall edge state device. This is accomplished via the development of an analytical method to calculate the full counting statistics of the problem in all the parameter regimes involving the temperature, the Hall voltage, and the gate voltage. PMID:21981487

  11. Realization of universal quantum cloning with superconducting quantum-interference device qubits in a cavity

    NASA Astrophysics Data System (ADS)

    Yang, Jian; Yu, Ya-Fei; Zhang, Zhi-Ming; Liu, Song-Hao

    2008-03-01

    We propose a scheme to realize a 1→2 universal quantum cloning machine with superconducting quantum interference device qubits, embedded in a high- Q cavity. The controlled-NOT operations are derived to present our scheme, and the two-photon Raman resonance processes are used to increase the operation rate. Compared with previous works, our scheme has advantages in the experimental realization and further utilization.

  12. Electronic simulation of a multiterminal quantum Hall effect device

    NASA Astrophysics Data System (ADS)

    Sosso, A.; Capra, P. P.

    1999-04-01

    A circuit with only resistors and unity gain amplifiers can be proven to be equivalent to the Ricketts and Kemeny electrical model of multiterminal quantum Hall effect (QHE) devices. By means of the new equivalent circuit, commercial software for electronic circuit analysis can be used to study a QHE measurement system. Moreover, it can be easily implemented, and we were able to build a circuit that simulates the electrical behavior of a QHE device. Particular care was taken in the design to reduce the effect of parasitic capacitances, which act as loads connected to the device terminals. Bootstrap buffers have been adopted to significantly reduce the capacitance of input stage. The small residual loading effect can be calculated and eliminated, allowing simulation of a QHE device with good accuracy.

  13. Advanced colour processing for mobile devices

    NASA Astrophysics Data System (ADS)

    Gillich, Eugen; Dörksen, Helene; Lohweg, Volker

    2015-02-01

    Mobile devices such as smartphones are going to play an important role in professionally image processing tasks. However, mobile systems were not designed for such applications, especially in terms of image processing requirements like stability and robustness. One major drawback is the automatic white balance, which comes with the devices. It is necessary for many applications, but of no use when applied to shiny surfaces. Such an issue appears when image acquisition takes place in differently coloured illuminations caused by different environments. This results in inhomogeneous appearances of the same subject. In our paper we show a new approach for handling the complex task of generating a low-noise and sharp image without spatial filtering. Our method is based on the fact that we analyze the spectral and saturation distribution of the channels. Furthermore, the RGB space is transformed into a more convenient space, a particular HSI space. We generate the greyscale image by a control procedure that takes into account the colour channels. This leads in an adaptive colour mixing model with reduced noise. The results of the optimized images are used to show how, e. g., image classification benefits from our colour adaptation approach.

  14. Advances in modeling and simulation of vacuum electronic devices

    SciTech Connect

    Antonsen, T.M. Jr.; Mondelli, A.A.; Levush, B.; Verboncoeur, J.P.; Birdsall, C.K.

    1999-05-01

    Recent advances in the modeling and simulation of vacuum electronic devices are reviewed. Design of these devices makes use of a variety of physical models and numerical code types. Progress in the development of these models and codes is outlined and illustrated with specific examples. The state of the art in device simulation is evolving to the point such that devices can be designed on the computer, thereby eliminating many trial and error fabrication and test steps. The role of numerical simulation in the design process can be expected to grow further in the future.

  15. Device-independent tomography of multipartite quantum states

    NASA Astrophysics Data System (ADS)

    Pál, Károly F.; Vértesi, Tamás; Navascués, Miguel

    2014-10-01

    In the usual tomography of multipartite entangled quantum states one assumes that the measurement devices used in the laboratory are under perfect control of the experimenter. In this paper, using the so-called swap concept introduced recently, we show how one can remove this assumption in realistic experimental conditions and nevertheless be able to characterize the produced multipartite state based only on observed statistics. Such a black-box tomography of quantum states is termed self-testing. As a function of the magnitude of the Bell violation, we are able to self-test emblematic multipartite quantum states such as the three-qubit W state, the three- and four-qubit Greenberger-Horne-Zeilinger states, and the four-qubit linear cluster state.

  16. Existence of an independent phonon bath in a quantum device

    NASA Astrophysics Data System (ADS)

    Pascal, L. M. A.; Fay, A.; Winkelmann, C. B.; Courtois, H.

    2013-09-01

    At low temperatures, the thermal wavelength of acoustic phonons in a metallic thin film on a substrate can widely exceed the film thickness. It is thus generally believed that a mesoscopic device operating at low temperature does not carry an individual phonon population. In this work, we provide direct experimental evidence for the thermal decoupling of phonons in a mesoscopic quantum device from its substrate phonon heat bath at a sub-Kelvin temperature. A simple heat balance model assuming an independent phonon bath following the usual electron-phonon and Kapitza coupling laws can account for all experimental observations.

  17. Matrix method analysis of quantum Hall effect device connections

    NASA Astrophysics Data System (ADS)

    Ortolano, M.; Callegaro, L.

    2012-02-01

    The modelling of electrical connections of single, or several, multiterminal quantum Hall effect (QHE) devices is relevant for electrical metrology: it is known, in fact, that certain particular connections allow (i) the realization of multiples or fractions of the quantized resistance, or (ii) the rejection of stray impedances, so that the configuration maintains the status of quantum standard. Ricketts-Kemeny and Delahaye equivalent circuits are known to be accurate models of the QHE: however, the numerical or analytical solution of electrical networks including these equivalent circuits can be difficult. In this paper, we introduce a method of analysis based on the representation of a QHE device by means of the indefinite admittance matrix: external connections are then represented with another matrix, easily written by inspection. Some examples, including the solution of double- and triple-series connections, are shown.

  18. Experimental investigations of quantum confined silicon nanoparticle light emitting devices

    NASA Astrophysics Data System (ADS)

    Ligman, Rebekah Kristine

    2007-12-01

    As the demands on our world's energy resources continue to grow, alternative high efficiency materials such as quantum confined silicon nanoparticles (Si nps) are desirable for their potential low cost application in white light illumination, in optical displays, and in on-chip optical interconnects. Many fabrication and passivation techniques exist that produce Si nps with high photogenerated quantum yield. However, high electrically generated Si np quantum efficiency has eluded our society. Predominantly due to the lack of a stable surface passivation and a device fabrication technique that preserves the Si np optical properties. To amend these deficiencies, the passivation of nonthermal plasma fabricated Si nps with a surface oxide grown under UV exposure was first investigated. Control over the surface oxidized Si np (Si/SiO2) passivation growth was demonstrated and the optical stability of Si/SiO2 nps was suitable for demonstrating Si np electroluminescence (EL). Two approaches for constructing hybrid organic light emitting diode (OLED) devices around nonthermal plasma fabricated Si nps were then investigated. Multilayer devices, composed of a nonthermal plasma fabricated Si np layer embedded within an OLED, were first studied. However, no EL from Si nps was obtained using the multilayer device architecture due to poor control over the Si np film thickness. Single layer polymer(Si/SiO2) hybrid devices, composed of nps randomly dispersed within an extrinsic conductive polymer, were then studied and EL from Si/SiO2 nps was obtained. The hybrid device optical and electrical response was enhanced over the control devices, possibly due to morphology changes induced by the Si/SiO2 nps. The energy transfer (ET) processes in single layer polymer(Si/SiO 2) hybrid devices were then investigated by imposing known spatial separations between the intrinsic conductive polymers and Si/SiO2 nps. No measurable Si/SiO2 np emission was observed from the intrinsic hybrid devices

  19. Microscopy imaging device with advanced imaging properties

    SciTech Connect

    Ghosh, Kunal; Burns, Laurie; El Gamal, Abbas; Schnitzer, Mark J.; Cocker, Eric; Ho, Tatt Wei

    2015-11-24

    Systems, methods and devices are implemented for microscope imaging solutions. One embodiment of the present disclosure is directed toward an epifluorescence microscope. The microscope includes an image capture circuit including an array of optical sensor. An optical arrangement is configured to direct excitation light of less than about 1 mW to a target object in a field of view of that is at least 0.5 mm.sup.2 and to direct epi-fluorescence emission caused by the excitation light to the array of optical sensors. The optical arrangement and array of optical sensors are each sufficiently close to the target object to provide at least 2.5 .mu.m resolution for an image of the field of view.

  20. Method of making an improved superconducting quantum interference device

    DOEpatents

    Wu, Cheng-Teh; Falco, Charles M.; Kampwirth, Robert T.

    1977-01-01

    An improved superconducting quantum interference device is made by sputtering a thin film of an alloy of three parts niobium to one part tin in a pattern comprising a closed loop with a narrow region, depositing a thin film of a radiation shield such as copper over the niobium-tin, scribing a narrow line in the copper over the narrow region, exposing the structure at the scribed line to radiation and removing the deposited copper.

  1. A multiscale quantum mechanics/electromagnetics method for device simulations.

    PubMed

    Yam, ChiYung; Meng, Lingyi; Zhang, Yu; Chen, GuanHua

    2015-04-01

    Multiscale modeling has become a popular tool for research applying to different areas including materials science, microelectronics, biology, chemistry, etc. In this tutorial review, we describe a newly developed multiscale computational method, incorporating quantum mechanics into electronic device modeling with the electromagnetic environment included through classical electrodynamics. In the quantum mechanics/electromagnetics (QM/EM) method, the regions of the system where active electron scattering processes take place are treated quantum mechanically, while the surroundings are described by Maxwell's equations and a semiclassical drift-diffusion model. The QM model and the EM model are solved, respectively, in different regions of the system in a self-consistent manner. Potential distributions and current densities at the interface between QM and EM regions are employed as the boundary conditions for the quantum mechanical and electromagnetic simulations, respectively. The method is illustrated in the simulation of several realistic systems. In the case of junctionless field-effect transistors, transfer characteristics are obtained and a good agreement between experiments and simulations is achieved. Optical properties of a tandem photovoltaic cell are studied and the simulations demonstrate that multiple QM regions are coupled through the classical EM model. Finally, the study of a carbon nanotube-based molecular device shows the accuracy and efficiency of the QM/EM method. PMID:25611987

  2. High-rate measurement-device-independent quantum cryptography

    NASA Astrophysics Data System (ADS)

    Pirandola, Stefano; Ottaviani, Carlo; Spedalieri, Gaetana; Weedbrook, Christian; Braunstein, Samuel L.; Lloyd, Seth; Gehring, Tobias; Jacobsen, Christian S.; Andersen, Ulrik L.

    2015-06-01

    Quantum cryptography achieves a formidable task—the remote distribution of secret keys by exploiting the fundamental laws of physics. Quantum cryptography is now headed towards solving the practical problem of constructing scalable and secure quantum networks. A significant step in this direction has been the introduction of measurement-device independence, where the secret key between two parties is established by the measurement of an untrusted relay. Unfortunately, although qubit-implemented protocols can reach long distances, their key rates are typically very low, unsuitable for the demands of a metropolitan network. Here we show, theoretically and experimentally, that a solution can come from the use of continuous-variable systems. We design a coherent-state network protocol able to achieve remarkably high key rates at metropolitan distances, in fact three orders of magnitude higher than those currently achieved. Our protocol could be employed to build high-rate quantum networks where devices securely connect to nearby access points or proxy servers.

  3. The theory research of multi-user quantum access network with Measurement Device Independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Ji, Yi-Ming; Li, Yun-Xia; Shi, Lei; Meng, Wen; Cui, Shu-Min; Xu, Zhen-Yu

    2015-10-01

    Quantum access network can't guarantee the absolute security of multi-user detector and eavesdropper can get access to key information through time-shift attack and other ways. Measurement-device-independent quantum key distribution is immune from all the detection attacks, and accomplishes the safe sharing of quantum key. In this paper, that Measurement-device-independent quantum key distribution is used in the application of multi-user quantum access to the network is on the research. By adopting time-division multiplexing technology to achieve the sharing of multiuser detector, the system structure is simplified and the security of quantum key sharing is acquired.

  4. Advanced devices and systems for radiation measurements

    SciTech Connect

    Knoll, G.F.; Wehe, D.K.; He, Z.; Barrett, C.; Miyamoto, J.

    1996-06-01

    The authors` most recent work continues their long-standing efforts to develop semiconductor detectors based on the collection of only a single type of charge carrier. Their best results are an extension of the principle of coplanar electrodes first described by Paul Luke of Lawrence Berkeley Laboratory 18 months ago. This technique, described in past progress reports, has the effect of deriving an output signal from detectors that depends only on the motion of carriers close to one surface. Since nearly all of these carriers are of one type (electrons) that are attracted to that electrode, the net effect is to nearly eliminate the influence of hole motion on the properties of the output signal. The result is that the much better mobility of electrons in compound semiconductors materials such as CZT can now be exploited without the concurrent penalty of poor hole collection. They have also developed new techniques in conjunction with the coplanar electrode principle that extends the technique into a new dimension. By proper processing of signals from the opposite electrode (the cathode) from the coplanar surface, they are able to derive a signal that is a good indication of the depth of interaction at which the charge carriers were initially formed. They have been the first group to demonstrate this technique, and examples of separate pulse height spectra recorded at a variety of different depths of interaction are shown in several of the figures that follow. Obtaining depth information is one step in the direction of obtaining volumetric point-of-interaction information from the detector. If one could known the coordinates of each specific interaction, then corrections could be applied to account for the inhomogeneities that currently plague many room-temperature devices.

  5. Advanced Stress, Strain And Geometrical Analysis In Semiconductor Devices

    SciTech Connect

    Neels, Antonia; Dommann, Alex; Niedermann, Philippe; Farub, Claudiu; Kaenel, Hans von

    2010-11-24

    High stresses and defect densities increases the risk of semiconductor device failure. Reliability studies on potential failure sources have an impact on design and are essential to assure the long term functioning of the device. Related to the dramatically smaller volume of semiconductor devices and new bonding techniques on such devices, new methods in testing and qualification are needed. Reliability studies on potential failure sources have an impact on design and are essential to assure the long term functioning of the device. In this paper, the applications of advanced High Resolution X-ray Diffraction (HRXRD) methods in strain, defect and deformation analysis on semiconductor devices are discussed. HRXRD with Rocking Curves (RC's) and Reciprocal Space Maps (RSM's) is used as accurate, non-destructive experimental method to evaluate the crystalline quality, and more precisely for the given samples, the in-situ strain, defects and geometrical parameters such as tilt and bending of device. The combination with advanced FEM simulations gives the possibility to support efficiently semiconductor devices design.

  6. Future Opportunities for Advancing Glucose Test Device Electronics

    PubMed Central

    Young, Brian R; Young, Teresa L; Joyce, Margaret K; Kennedy, Spencer I; Atashbar, Massood Z

    2011-01-01

    Advancements in the field of printed electronics can be applied to the field of diabetes testing. A brief history and some new developments in printed electronics components applicable to personal test devices, including circuitry, batteries, transmission devices, displays, and sensors, are presented. Low-cost, thin, and lightweight materials containing printed circuits with energy storage or harvest capability and reactive/display centers, made using new printing/imaging technologies, are ideal for incorporation into personal-use medical devices such as glucose test meters. Semicontinuous rotogravure printing, which utilizes flexible substrates and polymeric, metallic, and/or nano “ink” composite materials to effect rapidly produced, lower-cost printed electronics, is showing promise. Continuing research advancing substrate, “ink,” and continuous processing development presents the opportunity for research collaboration with medical device designers. PMID:22027300

  7. Stability of spintronic devices based on quantum ring networks

    NASA Astrophysics Data System (ADS)

    Földi, Péter; Kálmán, Orsolya; Peeters, F. M.

    2009-09-01

    Transport properties in mesoscopic networks are investigated, where the strength of the (Rashba-type) spin-orbit coupling is tuned with external gate voltages. We analyze in detail to what extent the ideal behavior and functionality of some promising network-based devices are modified by random (spin-dependent) scattering events and by thermal fluctuations. It is found that although the functionality of these devices is obviously based on the quantum coherence of the transmitted electrons, there is a certain stability: moderate level of errors can be tolerated. For mesoscopic networks made of typical semiconductor materials, we found that when the energy distribution of the input carriers is narrow enough, the devices can operate close to their ideal limits even at relatively high temperature. As an example, we present results for two different networks: one that realizes a Stern-Gerlach device and another that simulates a spin quantum walker. Finally we propose a simple network that can act as a narrow band energy filter even in the presence of random scatterers.

  8. An Integrated Quantum Dot Barcode Smartphone Optical Device for Wireless Multiplexed Diagnosis of Infected Patients

    NASA Astrophysics Data System (ADS)

    Ming, Kevin

    Integrating mobile-cellular devices with multiplex molecular diagnostics can potentially provide the most powerful platform for tracking, managing and preventing the transmission of infectious diseases. With over 6.9 billion subscriptions globally, handheld mobile-cellular devices can be programmed to spatially map, temporally track, and transmit information on infections over wide geographical space and boundaries. Current cell phone diagnostic technologies have poor limit of detection, dynamic range, and cannot detect multiple pathogen targets simultaneously, limiting their utility to single infections with high load. Here we combined recent advances in quantum dot barcode technology for molecular detection with smartphones to engineer a simple and low-cost chip-based wireless multiplex diagnostic device. We validated our device using a variety of synthetic genomic targets for the respiratory virus and blood-borne pathogens, and demonstrated that it could detect clinical samples after simple amplification. More importantly, we confirmed that the device is capable of detecting patients infected with a single or multiple infectious pathogens (e.g., HIV and hepatitis B) in a single test. This device advances the capacity for global surveillance of infectious diseases and has the potential to accelerate knowledge exchange-transfer of emerging or exigent disease threats with healthcare and military organizations in real-time.

  9. Quantum Well and Quantum Dot Modeling for Advanced Infrared Detectors and Focal Plane Arrays

    NASA Technical Reports Server (NTRS)

    Ting, David; Gunapala, S. D.; Bandara, S. V.; Hill, C. J.

    2006-01-01

    This viewgraph presentation reviews the modeling of Quantum Well Infrared Detectors (QWIP) and Quantum Dot Infrared Detectors (QDIP) in the development of Focal Plane Arrays (FPA). The QWIP Detector being developed is a dual band detector. It is capable of running on two bands Long-Wave Infrared (LWIR) and Medium Wavelength Infrared (MWIR). The same large-format dual-band FPA technology can be applied to Quantum Dot Infrared Photodetector (QDIP) with no modification, once QDIP exceeds QWIP in single device performance. Details of the devices are reviewed.

  10. Virtual Learning Environment for Interactive Engagement with Advanced Quantum Mechanics

    NASA Astrophysics Data System (ADS)

    Pedersen, Mads Kock; Skyum, Birk; Heck, Robert; Müller, Romain; Bason, Mark; Lieberoth, Andreas; Sherson, Jacob F.

    2016-06-01

    A virtual learning environment can engage university students in the learning process in ways that the traditional lectures and lab formats cannot. We present our virtual learning environment StudentResearcher, which incorporates simulations, multiple-choice quizzes, video lectures, and gamification into a learning path for quantum mechanics at the advanced university level. StudentResearcher is built upon the experiences gathered from workshops with the citizen science game Quantum Moves at the high-school and university level, where the games were used extensively to illustrate the basic concepts of quantum mechanics. The first test of this new virtual learning environment was a 2014 course in advanced quantum mechanics at Aarhus University with 47 enrolled students. We found increased learning for the students who were more active on the platform independent of their previous performances.

  11. Robust and Versatile Black-Box Certification of Quantum Devices

    NASA Astrophysics Data System (ADS)

    Yang, Tzyh Haur; Vértesi, Tamás; Bancal, Jean-Daniel; Scarani, Valerio; Navascués, Miguel

    2014-07-01

    Self-testing refers to the fact that, in some quantum devices, both states and measurements can be assessed in a black-box scenario, on the sole basis of the observed statistics, i.e., without reference to any prior device calibration. Only a few examples of self-testing are known, and they just provide nontrivial assessment for devices performing unrealistically close to the ideal case. We overcome these difficulties by approaching self-testing with the semidefinite programing hierarchy for the characterization of quantum correlations. This allows us to improve dramatically the robustness of previous self-testing schemes; e.g., we show that a Clauser-Horne-Shimony-Holt violation larger than 2.57 certifies a singlet fidelity of more than 70%. In addition, the versatility of the tool brings about self-testing of hitherto impossible cases, such as the robust self-testing of nonmaximally entangled two-qutrit states in the Collins-Gisin-Linden-Massar-Popescu scenario.

  12. Robust and versatile black-box certification of quantum devices.

    PubMed

    Yang, Tzyh Haur; Vértesi, Tamás; Bancal, Jean-Daniel; Scarani, Valerio; Navascués, Miguel

    2014-07-25

    Self-testing refers to the fact that, in some quantum devices, both states and measurements can be assessed in a black-box scenario, on the sole basis of the observed statistics, i.e., without reference to any prior device calibration. Only a few examples of self-testing are known, and they just provide nontrivial assessment for devices performing unrealistically close to the ideal case. We overcome these difficulties by approaching self-testing with the semidefinite programing hierarchy for the characterization of quantum correlations. This allows us to improve dramatically the robustness of previous self-testing schemes; e.g., we show that a Clauser-Horne-Shimony-Holt violation larger than 2.57 certifies a singlet fidelity of more than 70%. In addition, the versatility of the tool brings about self-testing of hitherto impossible cases, such as the robust self-testing of nonmaximally entangled two-qutrit states in the Collins-Gisin-Linden-Massar-Popescu scenario. PMID:25105599

  13. Statistical benchmarking for orthogonal electrostatic quantum dot qubit devices

    NASA Astrophysics Data System (ADS)

    Gamble, John; Frees, Adam; Friesen, Mark; Coppersmith, S. N.

    2014-03-01

    Quantum dots in semiconductor systems have emerged as attractive candidates for the implementation of quantum information processors because of the promise of scalability, manipulability, and integration with existing classical electronics. A limitation in current devices is that the electrostatic gates used for qubit manipulation exhibit strong cross-capacitance, presenting a barrier for practical scale-up. Here, we introduce a statistical framework for making precise the notion of orthogonality. We apply our method to analyze recently implemented designs at the University of Wisconsin-Madison that exhibit much increased orthogonal control than was previously possible. We then use our statistical modeling to future device designs, providing practical guidelines for devices to have robust control properties. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy Nuclear Security Administration under contract DE-AC04-94AL85000. The views and conclusions contained in this document are those of the authors and should not be interpreted as representing the official policies, either expressly or implied, of the US Government. This work was supported in part by the Laboratory Directed Research and Development program at Sandia National Laboratories, by ARO (W911NF-12-0607), and by the United States Department of Defense.

  14. Recent Advances in Quantum Dynamics of Bimolecular Reactions

    NASA Astrophysics Data System (ADS)

    Zhang, Dong H.; Guo, Hua

    2016-05-01

    In this review, we survey the latest advances in theoretical understanding of bimolecular reaction dynamics in the past decade. The remarkable recent progress in this field has been driven by more accurate and efficient ab initio electronic structure theory, effective potential-energy surface fitting techniques, and novel quantum scattering algorithms. Quantum mechanical characterization of bimolecular reactions continues to uncover interesting dynamical phenomena in atom-diatom reactions and beyond, reaching an unprecedented level of sophistication. In tandem with experimental explorations, these theoretical developments have greatly advanced our understanding of key issues in reaction dynamics, such as microscopic reaction mechanisms, mode specificity, product energy disposal, influence of reactive resonances, and nonadiabatic effects.

  15. Josephson phase diffusion in the superconducting quantum interference device ratchet.

    PubMed

    Spiechowicz, Jakub; Łuczka, Jerzy

    2015-05-01

    We study diffusion of the Josephson phase in the asymmetric superconducting quantum interference device (SQUID) subjected to a time-periodic current and pierced by an external magnetic flux. We analyze a relation between phase diffusion and quality of transport characterized by the dc voltage across the SQUID and efficiency of the device. In doing so, we concentrate on the previously reported regime [J. Spiechowicz and J. Łuczka, New J. Phys. 17, 023054 (2015)] for which efficiency of the SQUID attains a global maximum. For long times, the mean-square displacement of the phase is a linear function of time, meaning that diffusion is normal. Its coefficient is small indicating rather regular phase evolution. However, it can be magnified several times by tailoring experimentally accessible parameters like amplitudes of the ac current or external magnetic flux. Finally, we prove that in the deterministic limit this regime is essentially non-chaotic and possesses an unexpected simplicity of attractors. PMID:26026322

  16. Nano-superconducting quantum interference devices with suspended junctions

    SciTech Connect

    Hazra, D.; Hasselbach, K.; Kirtley, J. R.

    2014-04-14

    Nano-Superconducting Quantum Interference Devices (nano-SQUIDs) are usually fabricated from a single layer of either Nb or Al. We describe here a simple method for fabricating suspended nano-bridges in Nb/Al thin-film bilayers. We use these suspended bridges, which act as Josephson weak links, to fabricate nano-SQUIDs which show critical current oscillations at temperatures up to 1.5 K and magnetic flux densities up to over 20 mT. These nano-SQUIDs exhibit flux modulation depths intermediate between all-Al and all-Nb devices, with some of the desirable characteristics of both. The suspended geometry is attractive for magnetic single nanoparticle measurements.

  17. Josephson phase diffusion in the superconducting quantum interference device ratchet

    SciTech Connect

    Spiechowicz, Jakub; Łuczka, Jerzy

    2015-05-15

    We study diffusion of the Josephson phase in the asymmetric superconducting quantum interference device (SQUID) subjected to a time-periodic current and pierced by an external magnetic flux. We analyze a relation between phase diffusion and quality of transport characterized by the dc voltage across the SQUID and efficiency of the device. In doing so, we concentrate on the previously reported regime [J. Spiechowicz and J. Łuczka, New J. Phys. 17, 023054 (2015)] for which efficiency of the SQUID attains a global maximum. For long times, the mean-square displacement of the phase is a linear function of time, meaning that diffusion is normal. Its coefficient is small indicating rather regular phase evolution. However, it can be magnified several times by tailoring experimentally accessible parameters like amplitudes of the ac current or external magnetic flux. Finally, we prove that in the deterministic limit this regime is essentially non-chaotic and possesses an unexpected simplicity of attractors.

  18. Advances in device and formulation technologies for pulmonary drug delivery.

    PubMed

    Chan, John Gar Yan; Wong, Jennifer; Zhou, Qi Tony; Leung, Sharon Shui Yee; Chan, Hak-Kim

    2014-08-01

    Inhaled pharmaceuticals are formulated and delivered differently according to the therapeutic indication. However, specific device-formulation coupling is often fickle, and new medications or indications also demand new strategies. The discontinuation of chlorofluorocarbon propellants has seen replacement of older metered dose inhalers with dry powder inhaler formulations. High-dose dry powder inhalers are increasingly seen as an alternative dosage form for nebulised medications. In other cases, new medications have completely bypassed conventional inhalers and been formulated for use with unique inhalers such as the Staccato® device. Among these different devices, integration of software and electronic assistance has become a shared trend. This review covers recent device and formulation advances that are forming the current landscape of inhaled therapeutics. PMID:24728868

  19. Advanced photon source experience with vacuum chambers for insertion devices

    SciTech Connect

    Hartog, P.D.; Grimmer, J.; Xu, S.; Trakhtenberg, E.; Wiemerslage, G.

    1997-08-01

    During the last five years, a new approach to the design and fabrication of extruded aluminum vacuum chambers for insertion devices was developed at the Advanced Photon Source (APS). With this approach, three different versions of the vacuum chamber, with vertical apertures of 12 mm, 8 mm, and 5 mm, were manufactured and tested. Twenty chambers were installed into the APS vacuum system. All have operated with beam, and 16 have been coupled with insertion devices. Two different vacuum chambers with vertical apertures of 16 mm and 11 mm were developed for the BESSY-II storage ring and 3 of 16 mm chambers were manufactured.

  20. Advanced Sensor Fish Device for ImprovedTurbine Design

    SciTech Connect

    Carlson, Thomas J.

    2009-09-14

    Juvenile salmon (smolts) passing through hydroelectric turbines are subjected to environmental conditions that can potentially kill or injure them. Many turbines are reaching the end of their operational life expectancies and will be replaced with new turbines that incorporate advanced “fish friendly” designs devised to prevent injury and death to fish. To design a fish friendly turbine, it is first necessary to define the current conditions fish encounter. One such device used by biologists at Pacific Northwest National Laboratory was the sensor fish device to collect data that measures the forces fish experience during passage through hydroelectric projects.

  1. Measurement-device-independent quantum key distribution with pairs of vector vortex beams

    NASA Astrophysics Data System (ADS)

    Chen, Dong; Zhao, Shang-Hong; Shi, Lei; Liu, Yun

    2016-03-01

    The vector vortex (VV) beam, originally introduced to exhibit a form of single-particle quantum entanglement between different degrees of freedom, has specific applications for quantum-information protocols. In this paper, by combining measurement-device-independent quantum key distribution (MDIQKD) with a spontaneous parametric-downconversion source (SPDCS), we present a modified MDIQKD scheme with pairs of VV beams, which shows a structure of hybrid entangled entanglement corresponding to intrasystem entanglement and intersystem entanglement. The former entanglement, which is entangled between polarization and orbit angular momentum within each VV beam, is adopted to overcome the polarization misalignment associated with random rotations in quantum key distribution. The latter entanglement, which is entangled between the two VV beams, is used to perform the MDIQKD protocol with SPDCS to inherit the merit of the heralded process. The numerical simulations show that our modified scheme has apparent advances both in transmission distance and key-generation rate compared to the original MDIQKD. Furthermore, our modified protocol only needs to insert q plates in a practical experiment.

  2. Materials Advances for Next-Generation Ingestible Electronic Medical Devices.

    PubMed

    Bettinger, Christopher J

    2015-10-01

    Electronic medical implants have collectively transformed the diagnosis and treatment of many diseases, but have many inherent limitations. Electronic implants require invasive surgeries, operate in challenging microenvironments, and are susceptible to bacterial infection and persistent inflammation. Novel materials and nonconventional device fabrication strategies may revolutionize the way electronic devices are integrated with the body. Ingestible electronic devices offer many advantages compared with implantable counterparts that may improve the diagnosis and treatment of pathologies ranging from gastrointestinal infections to diabetes. This review summarizes current technologies and highlights recent materials advances. Specific focus is dedicated to next-generation materials for packaging, circuit design, and on-board power supplies that are benign, nontoxic, and even biodegradable. Future challenges and opportunities are also highlighted. PMID:26403162

  3. Insertion devices for the Advanced Light Source at LBL

    SciTech Connect

    Hassenzahl, W.; Chin, J.; Halbach, K.; Hoyer, E.; Humphries, D.; Kincaid, B.; Savoy, R.

    1989-03-01

    The Advanced Light Source (ALS) at the Lawrence Berkeley Laboratory will be the first of the new generation of dedicated synchrotron light sources to be put into operation. Specially designed insertion devices will be required to realize the high brightness photon beams made possible by the low emittance of the electron beam. The complement of insertion devices on the ALS will include undulators with periods as short as 3.9 cm and one or more high field wigglers. The first device to be designed is a 5 m long, 5 cm period, hybrid undulator. The goal of very high brightness and high harmonic output imposes unusually tight tolerances on the magnetic field quality and thus on the mechanical structure. The design process, using a generic structure for all undulators, is described. 5 refs., 4 figs., 1 tab.

  4. Recent Progress in Quantum Dot Based White Light-Emitting Devices.

    PubMed

    Su, Liang; Zhang, Xiaoyu; Zhang, Yu; Rogach, Andrey L

    2016-08-01

    Colloidal semiconductor quantum dots (QDs) have been widely employed as components of white light-emitting diodes (WLEDs) due to their excellent optical properties (highly saturated emission color, high luminescence quantum yield) as well as thermal and chemical stability. Much effort has been devoted to realize efficient QD-based WLEDs, including the synthesis of superior luminescent nanomaterials with excellent stabilities, and the design of advanced devices structures. In this paper, after introducing photometric parameters of the contemporary QD-based WLEDs, we highlight the recent progress in these devices grouped according to three main mechanisms for white light generation: optical excitation, direct charge carrier injection, and Förster resonance energy transfer. The methods to generate white light, the design of QD emitters and QD-based devices, as well as their fabrication techniques are considered, and the key scientific and technological challenges in the QD-based WLEDs are highlighted. Novel light-emitting materials for WLEDs such as carbon-based nanoparticles are also considered. PMID:27573394

  5. Quantum-ring spin interference device tuned by quantum point contacts

    SciTech Connect

    Diago-Cisneros, Leo; Mireles, Francisco

    2013-11-21

    We introduce a spin-interference device that comprises a quantum ring (QR) with three embedded quantum point contacts (QPCs) and study theoretically its spin transport properties in the presence of Rashba spin-orbit interaction. Two of the QPCs conform the lead-to-ring junctions while a third one is placed symmetrically in the upper arm of the QR. Using an appropriate scattering model for the QPCs and the S-matrix scattering approach, we analyze the role of the QPCs on the Aharonov-Bohm (AB) and Aharonov-Casher (AC) conductance oscillations of the QR-device. Exact formulas are obtained for the spin-resolved conductances of the QR-device as a function of the confinement of the QPCs and the AB/AC phases. Conditions for the appearance of resonances and anti-resonances in the spin-conductance are derived and discussed. We predict very distinctive variations of the QR-conductance oscillations not seen in previous QR proposals. In particular, we find that the interference pattern in the QR can be manipulated to a large extend by varying electrically the lead-to-ring topological parameters. The latter can be used to modulate the AB and AC phases by applying gate voltage only. We have shown also that the conductance oscillations exhibits a crossover to well-defined resonances as the lateral QPC confinement strength is increased, mapping the eigenenergies of the QR. In addition, unique features of the conductance arise by varying the aperture of the upper-arm QPC and the Rashba spin-orbit coupling. Our results may be of relevance for promising spin-orbitronics devices based on quantum interference mechanisms.

  6. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOEpatents

    Hilbert, C.; Martinis, J.M.; Clarke, J.

    1984-04-27

    A low noise radiofrequency amplifer, using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID and an input coil are maintained at superconductivity temperatures in a superconducting shield, with the input coil inductively coupled to the superconducting ring of the dc SQUID. A radiofrequency signal from outside the shield is applied to the input coil, and an amplified radiofrequency signal is developed across the dc SQUID ring and transmitted to exteriorly of the shield. A power gain of 19.5 +- 0.5 dB has been achieved with a noise temperature of 1.0 +- 0.4 K at a frequency of 100 MHz.

  7. Radiofrequency amplifier based on a dc superconducting quantum interference device

    DOEpatents

    Hilbert, Claude; Martinis, John M.; Clarke, John

    1986-01-01

    A low noise radiofrequency amplifier (10), using a dc SQUID (superconducting quantum interference device) as the input amplifying element. The dc SQUID (11) and an input coil (12) are maintained at superconductivity temperatures in a superconducting shield (13), with the input coil (12) inductively coupled to the superconducting ring (17) of the dc SQUID (11). A radiofrequency signal from outside the shield (13) is applied to the input coil (12), and an amplified radiofrequency signal is developed across the dc SQUID ring (17) and transmitted to exteriorly of the shield (13). A power gain of 19.5.+-.0.5 dB has been achieved with a noise temperature of 1.0.+-.0.4 K. at a frequency of 100 MHz.

  8. Cryogenic direct current superconducting quantum interference device readout circuit

    NASA Astrophysics Data System (ADS)

    Mück, Michael; Korn, Matthias; Mugford, C. G. A.; Kycia, J. B.

    2005-07-01

    We have designed and tested a superconducting quantum interference device (SQUID) readout circuit, which can be operated at liquid helium temperatures. Although room-temperature SQUID electronics perform well, it is sometimes desirable to keep the wires between SQUID, readout electronics, and feedback coil as short as possible to minimize phase shifts and time delays. Cooling the readout circuit to low temperatures can also decrease its thermal noise. Our readout circuit uses conventional ac-flux modulation, which significantly reduces low frequency excess noise and drift in the preamplifier. In this case, simple complementary metal-oxide-semiconductor circuits with low power dissipation can be used as amplifier, phase-sensitive detector and integrator. The power dissipation of the complete readout is less than 15mW at 5V supply voltage.

  9. Design and Simulation of Microwave Attenuators for Superconducting Quantum Devices

    NASA Astrophysics Data System (ADS)

    Lefebvre, Jay; Yeh, Jen-Hao; Wellstood, Frederick; Palmer, Benjamin

    We have found that dephasing times for quantum superconducting transmons operating nominally at T = 20 mK can be limited by thermal photons in the read-out cavity due to non-equilibrium noise on our input microwave line. In an effort to reduce this noise, we have used finite-element simulations to design attenuators that provide better thermalization of the input microwave signals being delivered to our devices. Our thermal simulations incorporate both electron-phonon decoupling effects due to dissipated power in each element of the attenuator as well as phonon thermal conduction and Kapitza boundary effects. We combine the resulting thermal map with a thermal noise model of each dissipative element of the filter to estimate the effective noise temperature of our filter design.

  10. Advanced in-situ electron-beam lithography for deterministic nanophotonic device processing.

    PubMed

    Kaganskiy, Arsenty; Gschrey, Manuel; Schlehahn, Alexander; Schmidt, Ronny; Schulze, Jan-Hindrik; Heindel, Tobias; Strittmatter, André; Rodt, Sven; Reitzenstein, Stephan

    2015-07-01

    We report on an advanced in-situ electron-beam lithography technique based on high-resolution cathodoluminescence (CL) spectroscopy at low temperatures. The technique has been developed for the deterministic fabrication and quantitative evaluation of nanophotonic structures. It is of particular interest for the realization and optimization of non-classical light sources which require the pre-selection of single quantum dots (QDs) with very specific emission features. The two-step electron-beam lithography process comprises (a) the detailed optical study and selection of target QDs by means of CL-spectroscopy and (b) the precise retrieval of the locations and integration of target QDs into lithographically defined nanostructures. Our technology platform allows for a detailed pre-process determination of important optical and quantum optical properties of the QDs, such as the emission energies of excitonic complexes, the excitonic fine-structure splitting, the carrier dynamics, and the quantum nature of emission. In addition, it enables a direct and precise comparison of the optical properties of a single QD before and after integration which is very beneficial for the quantitative evaluation of cavity-enhanced quantum devices. PMID:26233395

  11. Advanced in-situ electron-beam lithography for deterministic nanophotonic device processing

    NASA Astrophysics Data System (ADS)

    Kaganskiy, Arsenty; Gschrey, Manuel; Schlehahn, Alexander; Schmidt, Ronny; Schulze, Jan-Hindrik; Heindel, Tobias; Strittmatter, André; Rodt, Sven; Reitzenstein, Stephan

    2015-07-01

    We report on an advanced in-situ electron-beam lithography technique based on high-resolution cathodoluminescence (CL) spectroscopy at low temperatures. The technique has been developed for the deterministic fabrication and quantitative evaluation of nanophotonic structures. It is of particular interest for the realization and optimization of non-classical light sources which require the pre-selection of single quantum dots (QDs) with very specific emission features. The two-step electron-beam lithography process comprises (a) the detailed optical study and selection of target QDs by means of CL-spectroscopy and (b) the precise retrieval of the locations and integration of target QDs into lithographically defined nanostructures. Our technology platform allows for a detailed pre-process determination of important optical and quantum optical properties of the QDs, such as the emission energies of excitonic complexes, the excitonic fine-structure splitting, the carrier dynamics, and the quantum nature of emission. In addition, it enables a direct and precise comparison of the optical properties of a single QD before and after integration which is very beneficial for the quantitative evaluation of cavity-enhanced quantum devices.

  12. Advanced in-situ electron-beam lithography for deterministic nanophotonic device processing

    SciTech Connect

    Kaganskiy, Arsenty; Gschrey, Manuel; Schlehahn, Alexander; Schmidt, Ronny; Schulze, Jan-Hindrik; Heindel, Tobias; Rodt, Sven Reitzenstein, Stephan; Strittmatter, André

    2015-07-15

    We report on an advanced in-situ electron-beam lithography technique based on high-resolution cathodoluminescence (CL) spectroscopy at low temperatures. The technique has been developed for the deterministic fabrication and quantitative evaluation of nanophotonic structures. It is of particular interest for the realization and optimization of non-classical light sources which require the pre-selection of single quantum dots (QDs) with very specific emission features. The two-step electron-beam lithography process comprises (a) the detailed optical study and selection of target QDs by means of CL-spectroscopy and (b) the precise retrieval of the locations and integration of target QDs into lithographically defined nanostructures. Our technology platform allows for a detailed pre-process determination of important optical and quantum optical properties of the QDs, such as the emission energies of excitonic complexes, the excitonic fine-structure splitting, the carrier dynamics, and the quantum nature of emission. In addition, it enables a direct and precise comparison of the optical properties of a single QD before and after integration which is very beneficial for the quantitative evaluation of cavity-enhanced quantum devices.

  13. Storing quantum information for 30 seconds in a nanoelectronic device.

    PubMed

    Muhonen, Juha T; Dehollain, Juan P; Laucht, Arne; Hudson, Fay E; Kalra, Rachpon; Sekiguchi, Takeharu; Itoh, Kohei M; Jamieson, David N; McCallum, Jeffrey C; Dzurak, Andrew S; Morello, Andrea

    2014-12-01

    The spin of an electron or a nucleus in a semiconductor naturally implements the unit of quantum information--the qubit. In addition, because semiconductors are currently used in the electronics industry, developing qubits in semiconductors would be a promising route to realize scalable quantum information devices. The solid-state environment, however, may provide deleterious interactions between the qubit and the nuclear spins of surrounding atoms, or charge and spin fluctuations arising from defects in oxides and interfaces. For materials such as silicon, enrichment of the spin-zero (28)Si isotope drastically reduces spin-bath decoherence. Experiments on bulk spin ensembles in (28)Si crystals have indeed demonstrated extraordinary coherence times. However, it remained unclear whether these would persist at the single-spin level, in gated nanostructures near amorphous interfaces. Here, we present the coherent operation of individual (31)P electron and nuclear spin qubits in a top-gated nanostructure, fabricated on an isotopically engineered (28)Si substrate. The (31)P nuclear spin sets the new benchmark coherence time (>30 s with Carr-Purcell-Meiboom-Gill (CPMG) sequence) of any single qubit in the solid state and reaches >99.99% control fidelity. The electron spin CPMG coherence time exceeds 0.5 s, and detailed noise spectroscopy indicates that--contrary to widespread belief--it is not limited by the proximity to an interface. Instead, decoherence is probably dominated by thermal and magnetic noise external to the device, and is thus amenable to further improvement. PMID:25305745

  14. Storing quantum information for 30 seconds in a nanoelectronic device

    NASA Astrophysics Data System (ADS)

    Muhonen, Juha T.; Dehollain, Juan P.; Laucht, Arne; Hudson, Fay E.; Kalra, Rachpon; Sekiguchi, Takeharu; Itoh, Kohei M.; Jamieson, David N.; McCallum, Jeffrey C.; Dzurak, Andrew S.; Morello, Andrea

    2014-12-01

    The spin of an electron or a nucleus in a semiconductor naturally implements the unit of quantum information—the qubit. In addition, because semiconductors are currently used in the electronics industry, developing qubits in semiconductors would be a promising route to realize scalable quantum information devices. The solid-state environment, however, may provide deleterious interactions between the qubit and the nuclear spins of surrounding atoms, or charge and spin fluctuations arising from defects in oxides and interfaces. For materials such as silicon, enrichment of the spin-zero 28Si isotope drastically reduces spin-bath decoherence. Experiments on bulk spin ensembles in 28Si crystals have indeed demonstrated extraordinary coherence times. However, it remained unclear whether these would persist at the single-spin level, in gated nanostructures near amorphous interfaces. Here, we present the coherent operation of individual 31P electron and nuclear spin qubits in a top-gated nanostructure, fabricated on an isotopically engineered 28Si substrate. The 31P nuclear spin sets the new benchmark coherence time (>30 s with Carr-Purcell-Meiboom-Gill (CPMG) sequence) of any single qubit in the solid state and reaches >99.99% control fidelity. The electron spin CPMG coherence time exceeds 0.5 s, and detailed noise spectroscopy indicates that—contrary to widespread belief—it is not limited by the proximity to an interface. Instead, decoherence is probably dominated by thermal and magnetic noise external to the device, and is thus amenable to further improvement.

  15. Nanoengineered quantum dot medium for space optoelectronic devices

    NASA Astrophysics Data System (ADS)

    Oktyabrsky, S.; Tokranov, V.; Yakimov, M.; Sergeev, A.; Mitin, V.

    2012-10-01

    Resistance to temperature and ionizing radiation of space optoelectronic devices can be improved through control of carrier kinetics in nanoscale systems. Recent results in the science and technology of self-assembled heteroepitaxial InAs quantum dot (QD) medium related to photonic applications are discussed. Focus is placed on management of carrier kinetics via nanoengineering of electronic spectrum and potential profiles in the QD ensemble using modeling and controlled fabrication of QDs with molecular beam epitaxy. Shape-engineered QD sheets embedded into GaAs quantum wells were found to withstand two orders of magnitude higher proton dose than QWs and to account for high luminescence efficiency and thermally stable laser diodes. Built-in charge in QDs is responsible for improvement of both near and mid-IR optical absorption, but also control photoelectron lifetime in the structures. The negatively charged QD medium was the first QD material that has recently shown credible improvement of solar cell efficiency. It has resulted from IR energy harvesting and suppressed fast electron capture processes. It is thus expected that QD InAs/GaAs photovoltaics will overcome the efficiency and lifespan of multi-junction solar cells. Potentials due to QD built-in charge are also responsible for improved photoelectron lifetime in QD infrared photodetectors. QD correlated clusters provide even higher collective potential barriers around clusters and constitute the novel approach to the optoelectronic materials combining manageable photoelectron lifetime, high mobility, and tunable localized and conducting states.

  16. Recent Advances in Quantum Dynamics of Bimolecular Reactions.

    PubMed

    Zhang, Dong H; Guo, Hua

    2016-05-27

    In this review, we survey the latest advances in theoretical understanding of bimolecular reaction dynamics in the past decade. The remarkable recent progress in this field has been driven by more accurate and efficient ab initio electronic structure theory, effective potential-energy surface fitting techniques, and novel quantum scattering algorithms. Quantum mechanical characterization of bimolecular reactions continues to uncover interesting dynamical phenomena in atom-diatom reactions and beyond, reaching an unprecedented level of sophistication. In tandem with experimental explorations, these theoretical developments have greatly advanced our understanding of key issues in reaction dynamics, such as microscopic reaction mechanisms, mode specificity, product energy disposal, influence of reactive resonances, and nonadiabatic effects. PMID:26980305

  17. Bohm trajectories for the Monte Carlo simulation of quantum-based devices

    NASA Astrophysics Data System (ADS)

    Oriols, X.; García-García, J. J.; Martín, F.; Suñé, J.; González, T.; Mateos, J.; Pardo, D.

    1998-02-01

    A generalization of the classical ensemble Monte Carlo (MC) device simulation technique is proposed to simultaneously deal with quantum-mechanical phase-coherence effects and scattering interactions in quantum-based devices. The proposed method restricts the quantum treatment of transport to the regions of the device where the potential profile significantly changes in distances of the order of the de Broglie wavelength of the carriers (the quantum window). Bohm trajectories associated to time-dependent Gaussian wave packets are used to simulate the electron transport in the quantum window. Outside this window, the classical ensemble MC simulation technique is used. Classical and quantum trajectories are smoothly matched at the boundaries of the quantum window according to a criterium of total-energy conservation. A self-consistent one-dimensional simulator for resonant tunneling diodes has been developed to demonstrate the feasibility of our proposal.

  18. Device-independent quantum key distribution based on measurement inputs

    NASA Astrophysics Data System (ADS)

    Rahaman, Ramij; Parker, Matthew G.; Mironowicz, Piotr; Pawłowski, Marcin

    2015-12-01

    We provide an analysis of a family of device-independent quantum key distribution (QKD) protocols that has the following features. (a) The bits used for the secret key do not come from the results of the measurements on an entangled state but from the choices of settings. (b) Instead of a single security parameter (a violation of some Bell inequality) a set of them is used to estimate the level of trust in the secrecy of the key. The main advantage of these protocols is a smaller vulnerability to imperfect random number generators made possible by feature (a). We prove the security and the robustness of such protocols. We show that using our method it is possible to construct a QKD protocol which retains its security even if the source of randomness used by communicating parties is strongly biased. As a proof of principle, an explicit example of a protocol based on the Hardy's paradox is presented. Moreover, in the noiseless case, the protocol is secure in a natural way against any type of memory attack, and thus allows one to reuse the device in subsequent rounds. We also analyze the robustness of the protocol using semidefinite programming methods. Finally, we present a postprocessing method, and observe a paradoxical property that rejecting some random part of the private data can increase the key rate of the protocol.

  19. Realizing a partial general quantum cloning machine with superconducting quantum-interference devices in a cavity QED

    SciTech Connect

    Fang Baolong; Yang Zhen; Ye Liu

    2009-05-15

    We propose a scheme for implementing a partial general quantum cloning machine with superconducting quantum-interference devices coupled to a nonresonant cavity. By regulating the time parameters, our system can perform optimal symmetric (asymmetric) universal quantum cloning, optimal symmetric (asymmetric) phase-covariant cloning, and optimal symmetric economical phase-covariant cloning. In the scheme the cavity is only virtually excited, thus, the cavity decay is suppressed during the cloning operations.

  20. Quantum logical gates with four-level superconducting quantum interference devices coupled to a superconducting resonator

    SciTech Connect

    He Xiaoling; Luo Junyan; Yang Chuiping; Li Sheng; Han Siyuan

    2010-08-15

    We propose a way for realizing a two-qubit controlled phase gate with superconducting quantum interference devices (SQUIDs) coupled to a superconducting resonator. In this proposal, the two lowest levels of each SQUID serve as the logical states and two intermediate levels of each SQUID are used for the gate realization. We show that neither adjustment of SQUID level spacings during the gate operation nor uniformity in SQUID parameters is required by this proposal. In addition, this proposal does not require the adiabatic passage or a second-order detuning and thus the gate is much faster.

  1. TID Simulation of Advanced CMOS Devices for Space Applications

    NASA Astrophysics Data System (ADS)

    Sajid, Muhammad

    2016-07-01

    This paper focuses on Total Ionizing Dose (TID) effects caused by accumulation of charges at silicon dioxide, substrate/silicon dioxide interface, Shallow Trench Isolation (STI) for scaled CMOS bulk devices as well as at Buried Oxide (BOX) layer in devices based on Silicon-On-Insulator (SOI) technology to be operated in space radiation environment. The radiation induced leakage current and corresponding density/concentration electrons in leakage current path was presented/depicted for 180nm, 130nm and 65nm NMOS, PMOS transistors based on CMOS bulk as well as SOI process technologies on-board LEO and GEO satellites. On the basis of simulation results, the TID robustness analysis for advanced deep sub-micron technologies was accomplished up to 500 Krad. The correlation between the impact of technology scaling and magnitude of leakage current with corresponding total dose was established utilizing Visual TCAD Genius program.

  2. Advanced Measurement Devices for the Microgravity Electromagnetic Levitation Facility EML

    NASA Technical Reports Server (NTRS)

    Brillo, Jurgen; Fritze, Holger; Lohofer, Georg; Schulz, Michal; Stenzel, Christian

    2012-01-01

    This paper reports on two advanced measurement devices for the microgravity electromagnetic levitation facility (EML), which is currently under construction for the use onboard the "International Space Station (ISS)": the "Sample Coupling Electronics (SCE)" and the "Oxygen Sensing and Control Unit (OSC)". The SCE measures by a contactless, inductive method the electrical resistivity and the diameter of a spherical levitated metallic droplet by evaluating the voltage and electrical current applied to the levitation coil. The necessity of the OSC comes from the insight that properties like surface tension or, eventually, viscosity cannot seriously be determined by the oscillating drop method in the EML facility without knowing the conditions of the surrounding atmosphere. In the following both measurement devices are explained and laboratory test results are presented.

  3. The Advanced Space Plant Culture Device with Live Imaging Technique

    NASA Astrophysics Data System (ADS)

    Zheng, Weibo; Zhang, Tao; Tong, Guanghui

    The live imaging techniques, including the color and fluorescent imags, are very important and useful for space life science. The advanced space plant culture Device (ASPCD) with live imaging Technique, developed for Chinese Spacecraft, would be introduced in this paper. The ASPCD had two plant experimental chambers. Three cameras (two color cameras and one fluorescent camera) were installed in the two chambers. The fluorescent camera could observe flowering genes, which were labeled by GFP. The lighting, nutrient, temperature controling and water recycling were all independent in each chamber. The ASPCD would beed applied to investigate for the growth and development of the high plant under microgravity conditions on board the Chinese Spacecraft.

  4. Integrated Devices for Quantum Information with Polarization Encoded Qubits

    NASA Astrophysics Data System (ADS)

    Sansoni, Linda

    Quantum information deals with the information processing tasks that can be accomplished by using the laws of quantum mechanics. Its aim is to develop suitable strategies in particular for quantum computation and quantum communication, but also for quantum metrology and quantum simulation. In this chap. 1 briefly provide an introduction to the wide range of topics concerning quantum information and recall some basic theoretical elements, to which I will refer in this thesis.

  5. Self-assembled InAs/InP quantum dots and quantum dashes: Material structures and devices

    NASA Astrophysics Data System (ADS)

    Khan, Mohammed Zahed Mustafa; Ng, Tien Khee; Ooi, Boon S.

    2014-11-01

    The advances in lasers, electronic and photonic integrated circuits (EPIC), optical interconnects as well as the modulation techniques allow the present day society to embrace the convenience of broadband, high speed internet and mobile network connectivity. However, the steep increase in energy demand and bandwidth requirement calls for further innovation in ultra-compact EPIC technologies. In the optical domain, advancement in the laser technologies beyond the current quantum well (Qwell) based laser technologies are already taking place and presenting very promising results. Homogeneously grown quantum dot (Qdot) lasers and optical amplifiers, can serve in the future energy saving information and communication technologies (ICT) as the work-horse for transmitting and amplifying information through optical fiber. The encouraging results in the zero-dimensional (0D) structures emitting at 980 nm, in the form of vertical cavity surface emitting laser (VCSEL), are already operational at low threshold current density and capable of 40 Gbps error-free transmission at 108 fJ/bit. Subsequent achievements for lasers and amplifiers operating in the O-, C-, L-, U-bands, and beyond will eventually lay the foundation for green ICT. On the hand, the inhomogeneously grown quasi 0D quantum dash (Qdash) lasers are brilliant solutions for potential broadband connectivity in server farms or access network. A single broadband Qdash laser operating in the stimulated emission mode can replace tens of discrete narrow-band lasers in dense wavelength division multiplexing (DWDM) transmission thereby further saving energy, cost and footprint. We herein reviewed the1 progress of both Qdots and Qdash devices, based on the InAs/InGaAlAs/InP and InAs/InGaAsP/InP material systems, from the angles of growth and device performance. In particular, we discussed the progress in lasers, semiconductor optical amplifiers (SOA), mode locked lasers, and superluminescent diodes, which are the building

  6. Nanoscale Copper and Copper Compounds for Advanced Device Applications

    NASA Astrophysics Data System (ADS)

    Chen, Lih-Juann

    2016-04-01

    Copper has been in use for at least 10,000 years. Copper alloys, such as bronze and brass, have played important roles in advancing civilization in human history. Bronze artifacts date at least 6500 years. On the other hand, discovery of intriguing properties and new applications in contemporary technology for copper and its compounds, particularly on nanoscale, have continued. In this paper, examples for the applications of Cu and Cu alloys for advanced device applications will be given on Cu metallization in microelectronics devices, Cu nanobats as field emitters, Cu2S nanowire array as high-rate capability and high-capacity cathodes for lithium-ion batteries, Cu-Te nanostructures for field-effect transistor, Cu3Si nanowires as high-performance field emitters and efficient anti-reflective layers, single-crystal Cu(In,Ga)Se2 nanotip arrays for high-efficiency solar cell, multilevel Cu2S resistive memory, superlattice Cu2S-Ag2S heterojunction diodes, and facet-dependent Cu2O diode.

  7. Security analysis on some experimental quantum key distribution systems with imperfect optical and electrical devices

    NASA Astrophysics Data System (ADS)

    Liang, Lin-Mei; Sun, Shi-Hai; Jiang, Mu-Sheng; Li, Chun-Yan

    2014-10-01

    In general, quantum key distribution (QKD) has been proved unconditionally secure for perfect devices due to quantum uncertainty principle, quantum noncloning theorem and quantum nondividing principle which means that a quantum cannot be divided further. However, the practical optical and electrical devices used in the system are imperfect, which can be exploited by the eavesdropper to partially or totally spy the secret key between the legitimate parties. In this article, we first briefly review the recent work on quantum hacking on some experimental QKD systems with respect to imperfect devices carried out internationally, then we will present our recent hacking works in details, including passive faraday mirror attack, partially random phase attack, wavelength-selected photon-number-splitting attack, frequency shift attack, and single-photon-detector attack. Those quantum attack reminds people to improve the security existed in practical QKD systems due to imperfect devices by simply adding countermeasure or adopting a totally different protocol such as measurement-device independent protocol to avoid quantum hacking on the imperfection of measurement devices [Lo, et al., Phys. Rev. Lett., 2012, 108: 130503].

  8. Single donor electronics and quantum functionalities with advanced CMOS technology.

    PubMed

    Jehl, Xavier; Niquet, Yann-Michel; Sanquer, Marc

    2016-03-16

    Recent progresses in quantum dots technology allow fundamental studies of single donors in various semiconductor nanostructures. For the prospect of applications figures of merits such as scalability, tunability, and operation at relatively large temperature are of prime importance. Beyond the case of actual dopant atoms in a host crystal, similar arguments hold for small enough quantum dots which behave as artificial atoms, for instance for single spin control and manipulation. In this context, this experimental review focuses on the silicon-on-insulator devices produced within microelectronics facilities with only very minor modifications to the current industrial CMOS process and tools. This is required for scalability and enabled by shallow trench or mesa isolation. It also paves the way for real integration with conventional circuits, as illustrated by a nanoscale device coupled to a CMOS circuit producing a radio-frequency drive on-chip. At the device level we emphasize the central role of electrostatics in etched silicon nanowire transistors, which allows to understand the characteristics in the full range from zero to room temperature. PMID:26871255

  9. Single donor electronics and quantum functionalities with advanced CMOS technology

    NASA Astrophysics Data System (ADS)

    Jehl, Xavier; Niquet, Yann-Michel; Sanquer, Marc

    2016-03-01

    Recent progresses in quantum dots technology allow fundamental studies of single donors in various semiconductor nanostructures. For the prospect of applications figures of merits such as scalability, tunability, and operation at relatively large temperature are of prime importance. Beyond the case of actual dopant atoms in a host crystal, similar arguments hold for small enough quantum dots which behave as artificial atoms, for instance for single spin control and manipulation. In this context, this experimental review focuses on the silicon-on-insulator devices produced within microelectronics facilities with only very minor modifications to the current industrial CMOS process and tools. This is required for scalability and enabled by shallow trench or mesa isolation. It also paves the way for real integration with conventional circuits, as illustrated by a nanoscale device coupled to a CMOS circuit producing a radio-frequency drive on-chip. At the device level we emphasize the central role of electrostatics in etched silicon nanowire transistors, which allows to understand the characteristics in the full range from zero to room temperature.

  10. Recent advances in conjugated polymers for light emitting devices.

    PubMed

    Alsalhi, Mohamad Saleh; Alam, Javed; Dass, Lawrence Arockiasamy; Raja, Mohan

    2011-01-01

    A recent advance in the field of light emitting polymers has been the discovery of electroluminescent conjugated polymers, that is, kind of fluorescent polymers that emit light when excited by the flow of an electric current. These new generation fluorescent materials may now challenge the domination by inorganic semiconductor materials of the commercial market in light-emitting devices such as light-emitting diodes (LED) and polymer laser devices. This review provides information on unique properties of conjugated polymers and how they have been optimized to generate these properties. The review is organized in three sections focusing on the major advances in light emitting materials, recent literature survey and understanding the desirable properties as well as modern solid state lighting and displays. Recently, developed conjugated polymers are also functioning as roll-up displays for computers and mobile phones, flexible solar panels for power portable equipment as well as organic light emitting diodes in displays, in which television screens, luminous traffic, information signs, and light-emitting wallpaper in homes are also expected to broaden the use of conjugated polymers as light emitting polymers. The purpose of this review paper is to examine conjugated polymers in light emitting diodes (LEDs) in addition to organic solid state laser. Furthermore, since conjugated polymers have been approved as light-emitting organic materials similar to inorganic semiconductors, it is clear to motivate these organic light-emitting devices (OLEDs) and organic lasers for modern lighting in terms of energy saving ability. In addition, future aspects of conjugated polymers in LEDs were also highlighted in this review. PMID:21673938

  11. Recent Advances in Conjugated Polymers for Light Emitting Devices

    PubMed Central

    AlSalhi, Mohamad Saleh; Alam, Javed; Dass, Lawrence Arockiasamy; Raja, Mohan

    2011-01-01

    A recent advance in the field of light emitting polymers has been the discovery of electroluminescent conjugated polymers, that is, kind of fluorescent polymers that emit light when excited by the flow of an electric current. These new generation fluorescent materials may now challenge the domination by inorganic semiconductor materials of the commercial market in light-emitting devices such as light-emitting diodes (LED) and polymer laser devices. This review provides information on unique properties of conjugated polymers and how they have been optimized to generate these properties. The review is organized in three sections focusing on the major advances in light emitting materials, recent literature survey and understanding the desirable properties as well as modern solid state lighting and displays. Recently, developed conjugated polymers are also functioning as roll-up displays for computers and mobile phones, flexible solar panels for power portable equipment as well as organic light emitting diodes in displays, in which television screens, luminous traffic, information signs, and light-emitting wallpaper in homes are also expected to broaden the use of conjugated polymers as light emitting polymers. The purpose of this review paper is to examine conjugated polymers in light emitting diodes (LEDs) in addition to organic solid state laser. Furthermore, since conjugated polymers have been approved as light-emitting organic materials similar to inorganic semiconductors, it is clear to motivate these organic light-emitting devices (OLEDs) and organic lasers for modern lighting in terms of energy saving ability. In addition, future aspects of conjugated polymers in LEDs were also highlighted in this review. PMID:21673938

  12. Bell nonlocality: a resource for device-independent quantum information protocols

    NASA Astrophysics Data System (ADS)

    Acin, Antonio

    2015-05-01

    Bell nonlocality is not only one of the most fundamental properties of quantum physics, but has also recently acquired the status of an information resource for device-independent quantum information protocols. In the device-independent approach, protocols are designed so that their performance is independent of the internal working of the devices used in the implementation. We discuss all these ideas and argue that device-independent protocols are especially relevant or cryptographic applications, as they are insensitive to hacking attacks exploiting imperfections on the modelling of the devices.

  13. Advanced Silicon Solar Cell Device Physics and Design

    NASA Astrophysics Data System (ADS)

    Deceglie, Michael Gardner

    A fundamental challenge in the development and deployment of solar photovoltaic technology is a reduction in cost enabling direct competition with fossil-fuel-based energy sources. A key driver in this cost reduction is optimized device efficiency, because increased energy output leverages all photovoltaic system costs, from raw materials and module manufacturing to installation and maintenance. To continue progress toward higher conversion efficiencies, solar cells are being fabricated with increasingly complex designs, including engineered nanostructures, heterojunctions, and novel contacting and passivation schemes. Such advanced designs require a comprehensive and unified understanding of the optical and electrical device physics at the microscopic scale. This thesis focuses on a microscopic understanding of solar cell optoelectronic performance and its impact on cell optimization. We consider this in three solar cell platforms: thin-film crystalline silicon, amorphous/crystalline silicon heterojunctions, and thin-film cells with nanophotonic light trapping. The work described in this thesis represents a powerful design paradigm, based on a detailed physical understanding of the mechanisms governing solar cell performance. Furthermore, we demonstrate the importance of understanding not just the individual mechanisms, but also their interactions. Such an approach to device optimization is critical for the efficiency and competitiveness of future generations of solar cells.

  14. Engineering a Robust Photovoltaic Device with Quantum Dots and Bacteriorhodopsin.

    PubMed

    Renugopalakrishnan, Venkatesan; Barbiellini, Bernardo; King, Chris; Molinari, Michael; Mochalov, Konstantin; Sukhanova, Alyona; Nabiev, Igor; Fojan, Peter; Tuller, Harry L; Chin, Michael; Somasundaran, Ponisseril; Padrós, Esteve; Ramakrishna, Seeram

    2014-07-31

    We present a route toward a radical improvement in solar cell efficiency using resonant energy transfer and sensitization of semiconductor metal oxides with a light-harvesting quantum dot (QD)/bacteriorhodopsin (bR) layer designed by protein engineering. The specific aims of our approach are (1) controlled engineering of highly ordered bR/QD complexes; (2) replacement of the liquid electrolyte by a thin layer of gold; (3) highly oriented deposition of bR/QD complexes on a gold layer; and (4) use of the Forster resonance energy transfer coupling between bR and QDs to achieve an efficient absorbing layer for dye-sensitized solar cells. This proposed approach is based on the unique optical characteristics of QDs, on the photovoltaic properties of bR, and on state-of-the-art nanobioengineering technologies. It permits spatial and optical coupling together with control of hybrid material components on the bionanoscale. This method paves the way to the development of the solid-state photovoltaic device with the efficiency increased to practical levels. PMID:25383133

  15. Quantum Conductance in Silicon Oxide Resistive Memory Devices

    PubMed Central

    Mehonic, A.; Vrajitoarea, A.; Cueff, S.; Hudziak, S.; Howe, H.; Labbé, C.; Rizk, R.; Pepper, M.; Kenyon, A. J.

    2013-01-01

    Resistive switching offers a promising route to universal electronic memory, potentially replacing current technologies that are approaching their fundamental limits. In many cases switching originates from the reversible formation and dissolution of nanometre-scale conductive filaments, which constrain the motion of electrons, leading to the quantisation of device conductance into multiples of the fundamental unit of conductance, G0. Such quantum effects appear when the constriction diameter approaches the Fermi wavelength of the electron in the medium – typically several nanometres. Here we find that the conductance of silicon-rich silica (SiOx) resistive switches is quantised in half-integer multiples of G0. In contrast to other resistive switching systems this quantisation is intrinsic to SiOx, and is not due to drift of metallic ions. Half-integer quantisation is explained in terms of the filament structure and formation mechanism, which allows us to distinguish between systems that exhibit integer and half-integer quantisation. PMID:24048282

  16. Engineering a Robust Photovoltaic Device with Quantum Dots and Bacteriorhodopsin

    PubMed Central

    2015-01-01

    We present a route toward a radical improvement in solar cell efficiency using resonant energy transfer and sensitization of semiconductor metal oxides with a light-harvesting quantum dot (QD)/bacteriorhodopsin (bR) layer designed by protein engineering. The specific aims of our approach are (1) controlled engineering of highly ordered bR/QD complexes; (2) replacement of the liquid electrolyte by a thin layer of gold; (3) highly oriented deposition of bR/QD complexes on a gold layer; and (4) use of the Forster resonance energy transfer coupling between bR and QDs to achieve an efficient absorbing layer for dye-sensitized solar cells. This proposed approach is based on the unique optical characteristics of QDs, on the photovoltaic properties of bR, and on state-of-the-art nanobioengineering technologies. It permits spatial and optical coupling together with control of hybrid material components on the bionanoscale. This method paves the way to the development of the solid-state photovoltaic device with the efficiency increased to practical levels. PMID:25383133

  17. SQUID detected NMR and NQR. Superconducting Quantum Interference Device.

    PubMed

    Augustine, M P; TonThat, D M; Clarke, J

    1998-03-01

    The dc Superconducting QUantum Interference Device (SQUID) is a sensitive detector of magnetic flux, with a typical flux noise of the order 1 muphi0 Hz(-1/2) at liquid helium temperatures. Here phi0 = h/2e is the flux quantum. In our NMR or NQR spectrometer, a niobium wire coil wrapped around the sample is coupled to a thin film superconducting coil deposited on the SQUID to form a flux transformer. With this untuned input circuit the SQUID measures the flux, rather than the rate of change of flux, and thus retains its high sensitivity down to arbitrarily low frequencies. This feature is exploited in a cw spectrometer that monitors the change in the static magnetization of a sample induced by radio frequency irradiation. Examples of this technique are the detection of NQR in 27Al in sapphire and 11B in boron nitride, and a level crossing technique to enhance the signal of 14N in peptides. Research is now focused on a SQUID-based spectrometer for pulsed NQR and NMR, which has a bandwidth of 0-5 MHz. This spectrometer is used with spin-echo techniques to measure the NQR longitudinal and transverse relaxation times of 14N in NH4ClO4, 63+/-6 ms and 22+/-2 ms, respectively. With the aid of two-frequency pulses to excite the 359 kHz and 714 kHz resonances in ruby simultaneously, it is possible to obtain a two-dimensional NQR spectrum. As a third example, the pulsed spectrometer is used to study NMR spectrum of 129Xe after polariza-tion with optically pumped Rb. The NMR line can be detected at frequencies as low as 200 Hz. At fields below about 2 mT the longitudinal relaxation time saturates at about 2000 s. Two recent experiments in other laboratories have extended these pulsed NMR techniques to higher temperatures and smaller samples. In the first, images were obtained of mineral oil floating on water at room temperature. In the second, a SQUID configured as a thin film gradiometer was used to detect NMR in a 50 microm particle of 195Pt at 6 mT and 4.2 K. PMID:9650797

  18. Consistent low-field mobility modeling for advanced MOS devices

    NASA Astrophysics Data System (ADS)

    Stanojević, Zlatan; Baumgartner, Oskar; Filipović, Lidija; Kosina, Hans; Karner, Markus; Kernstock, Christian; Prause, Philipp

    2015-10-01

    In this paper we develop several extensions to semi-classical modeling of low-field mobility, which are necessary to treat planar and non-planar channel geometries on equal footing. We advance the state-of-the-art by generalizing the Prange-Nee model for surface roughness scattering to non-planar geometries, providing a fully numerical treatment of Coulomb scattering, and formulating the Kubo-Greenwood mobility model in a consistent, dimension-independent manner. These extensions allow meaningful comparison of planar and non-planar structures alike, and open the door to evaluating emerging device concepts, such as the FinFET or the junction-less transistor, on physical grounds.

  19. Control system for insertion devices at the advanced photon source

    SciTech Connect

    Makarov, Oleg A.; Den Hartog, Patric; Moog, Elizabeth R.; Smith, Martin L.

    1997-07-01

    Eighteen insertion devices (IDs) are installed at the Advanced Photon Source (APS), and three more are scheduled for installation by the end of this year. A distributed control system for insertion devices at the APS storage ring was created with the Experimental Physics and Industrial Control System (EPICS). The basic components of this system are operator interfaces (OPIs), input output controllers (IOCs), and a local area network that allows the OPI and IOC to communicate. The IOC operates under the VxWorks OS with an EPICS database and a sequencer. The sequencer runs an ID control program written in State Notation Language. The OPI is built with the EPICS tool MEDM and provides display screens with input and output fields and buttons for gap control of the IDs. Global commands like 'open all IDs' are C-shell scripts invoked from the display menu. The algorithms for control and protection of the ID and ID vacuum chamber and the accuracy of gap control are discussed.

  20. Control system for insertion devices at the Advanced Photon Source

    SciTech Connect

    Makarov, O.A.; Den Hartog, P.; Moog, E.R.; Smith, M.L.

    1997-09-01

    Eighteen insertion devices (IDs) are installed at the Advanced Photon Source (APS), and three more are scheduled for installation by the end of this year. A distributed control system for insertion devices at the APS storage ring was created with the Experimental Physics and Industrial Control System (EPICS). The basic components of this system are operator interfaces (OPIs), input output controllers (IOCs), and a local area network that allows the OPI and IOC to communicate. The IOC operates under the VxWorks OS with an EPICS database and a sequencer. The sequencer runs an ID control program written in State Notation Language. The OPI is built with the EPICS tool MEDM and provides display screens with input and output fields and buttons for gap control of the IDs. Global commands like ``open all IDs`` are C-shell scripts invoked from the display menu. The algorithms for control and protection of the ID and ID vacuum chamber and the accuracy of gap control are discussed.

  1. Control system for insertion devices at the advanced photon source

    SciTech Connect

    Makarov, O.A.; Den Hartog, P.; Moog, E.R.; Smith, M.L.

    1997-07-01

    Eighteen insertion devices (IDs) are installed at the Advanced Photon Source (APS), and three more are scheduled for installation by the end of this year. A distributed control system for insertion devices at the APS storage ring was created with the Experimental Physics and Industrial Control System (EPICS). The basic components of this system are operator interfaces (OPIs), input output controllers (IOCs), and a local area network that allows the OPI and IOC to communicate. The IOC operates under the VxWorks OS with an EPICS database and a sequencer. The sequencer runs an ID control program written in State Notation Language. The OPI is built with the EPICS tool MEDM and provides display screens with input and output fields and buttons for gap control of the IDs. Global commands like {open_quotes}open all IDs{close_quotes} are C-shell scripts invoked from the display menu. The algorithms for control and protection of the ID and ID vacuum chamber and the accuracy of gap control are discussed. {copyright} {ital 1997 American Institute of Physics.}

  2. Evaluation of Advanced COTS Passive Devices for Extreme Temperature Operation

    NASA Technical Reports Server (NTRS)

    Patterson, Richard; Hammoud, Ahmad; Dones, Keishla R.

    2009-01-01

    Electronic sensors and circuits are often exposed to extreme temperatures in many of NASA deep space and planetary surface exploration missions. Electronics capable of operation in harsh environments would be beneficial as they simplify overall system design, relax thermal management constraints, and meet operational requirements. For example, cryogenic operation of electronic parts will improve reliability, increase energy density, and extend the operational lifetimes of space-based electronic systems. Similarly, electronic parts that are able to withstand and operate efficiently in high temperature environments will negate the need for thermal control elements and their associated structures, thereby reducing system size and weight, enhancing its reliability, improving its efficiency, and reducing cost. Passive devices play a critical role in the design of almost all electronic circuitry. To address the needs of systems for extreme temperature operation, some of the advanced and most recently introduced commercial-off-the-shelf (COTS) passive devices, which included resistors and capacitors, were examined for operation under a wide temperature regime. The types of resistors investigated included high temperature precision film, general purpose metal oxide, and wirewound.

  3. Towards manufacturing of advanced logic devices by double-patterning

    NASA Astrophysics Data System (ADS)

    Koay, Chiew-seng; Halle, Scott; Holmes, Steven; Petrillo, Karen; Colburn, Matthew; van Dommelen, Youri; Jiang, Aiqin; Crouse, Michael; Dunn, Shannon; Hetzer, David; Kawakami, Shinichiro; Cantone, Jason; Huli, Lior; Rodgers, Martin; Martinick, Brian

    2011-04-01

    As reported previously, the IBM Alliance has established a DETO (Double-Expose-Track-Optimized) baseline, in collaboration with ASML, TEL, and CNSE, to evaluate commercially available DETO photoresist system for the manufacturing of advanced logic devices. Although EUV lithography is the baseline strategy for <2x nm logic nodes, alternative techniques are still being pursued. The DETO technique produces pitch-split patterns capable of supporting 16 nm and 11 nm node semiconductor devices. We present the long-term monitoring performances of CD uniformity (CDU), overlay, and defectivity of our DETO process. CDU and overlay performances for controlled experiments are also presented. Two alignment schemes in DETO are compared experimentally for their effects on inter-level & intralevel overlays, and space CDU. We also experimented with methods for improving CDU, in which the CD-OptimizerTMand DoseMapperTM were evaluated separately and in tandem. Overlay improvements using the Correction Per Exposure (CPE) and the intra-field High-Order Process Correction (i-HOPC) were compared against the usual linear correction method. The effects of the exposure field size are also compared between a small field and the full field. Included in all the above, we also compare the performances derived from stack-integrated wafers and bare-Si wafers.

  4. THz photoresponse of quantum Hall devices based on HgTe-Quantum wells

    NASA Astrophysics Data System (ADS)

    Gouider, F.; Hein, G.; Brüne, C.; Buhmann, H.; Vasilyev, Yu. B.; Nachtwei, G.

    2010-01-01

    This study concerns the experimental investigation of the Terahertz -(THz-) photoresponse in systems under quantum-Hall-(QH-) conditions. These investigations are interesting regarding a potential application of QH-systems as fast and spectrally sensitive THz-detectors. The measurements of the THz-photoresponse (PR) of devices with HgTe quantum wells (QWs) embedded in CdHgTe barriers are aimed at obtaining photosignals at smaller magnetic fields in comparison to detectors made of GaAs/AlGaAs wafers. This can be realized by changing the electron density (application of a gate electrode). The QWs have a thickness of dQW between 7 nm and 12 nm, so that the material HgTe of the QW possesses a semimetallic band structure. We found a cyclotron mass of about mc = 0.026 m0 for our samples from cyclotron resonance measurements (also approximately determined from our PR). As this cyclotron mass is by about a factor 3 smaller than the one of electrons in GaAs, the same Landau level splitting is reached at about 1/3 of the magnetic field as in GaAs.

  5. Advanced numerical methods and software approaches for semiconductor device simulation

    SciTech Connect

    CAREY,GRAHAM F.; PARDHANANI,A.L.; BOVA,STEVEN W.

    2000-03-23

    In this article the authors concisely present several modern strategies that are applicable to drift-dominated carrier transport in higher-order deterministic models such as the drift-diffusion, hydrodynamic, and quantum hydrodynamic systems. The approaches include extensions of upwind and artificial dissipation schemes, generalization of the traditional Scharfetter-Gummel approach, Petrov-Galerkin and streamline-upwind Petrov Galerkin (SUPG), entropy variables, transformations, least-squares mixed methods and other stabilized Galerkin schemes such as Galerkin least squares and discontinuous Galerkin schemes. The treatment is representative rather than an exhaustive review and several schemes are mentioned only briefly with appropriate reference to the literature. Some of the methods have been applied to the semiconductor device problem while others are still in the early stages of development for this class of applications. They have included numerical examples from the recent research tests with some of the methods. A second aspect of the work deals with algorithms that employ unstructured grids in conjunction with adaptive refinement strategies. The full benefits of such approaches have not yet been developed in this application area and they emphasize the need for further work on analysis, data structures and software to support adaptivity. Finally, they briefly consider some aspects of software frameworks. These include dial-an-operator approaches such as that used in the industrial simulator PROPHET, and object-oriented software support such as those in the SANDIA National Laboratory framework SIERRA.

  6. Advanced Numerical Methods and Software Approaches for Semiconductor Device Simulation

    DOE PAGESBeta

    Carey, Graham F.; Pardhanani, A. L.; Bova, S. W.

    2000-01-01

    In this article we concisely present several modern strategies that are applicable to driftdominated carrier transport in higher-order deterministic models such as the driftdiffusion, hydrodynamic, and quantum hydrodynamic systems. The approaches include extensions of “upwind” and artificial dissipation schemes, generalization of the traditional Scharfetter – Gummel approach, Petrov – Galerkin and streamline-upwind Petrov Galerkin (SUPG), “entropy” variables, transformations, least-squares mixed methods and other stabilized Galerkin schemes such as Galerkin least squares and discontinuous Galerkin schemes. The treatment is representative rather than an exhaustive review and several schemes are mentioned only briefly with appropriate reference to the literature. Some of themore » methods have been applied to the semiconductor device problem while others are still in the early stages of development for this class of applications. We have included numerical examples from our recent research tests with some of the methods. A second aspect of the work deals with algorithms that employ unstructured grids in conjunction with adaptive refinement strategies. The full benefits of such approaches have not yet been developed in this application area and we emphasize the need for further work on analysis, data structures and software to support adaptivity. Finally, we briefly consider some aspects of software frameworks. These include dial-an-operator approaches such as that used in the industrial simulator PROPHET, and object-oriented software support such as those in the SANDIA National Laboratory framework SIERRA.« less

  7. Josephson junction devices: Model quantum mechanical systems and medical applications

    NASA Astrophysics Data System (ADS)

    Chen, Josephine

    In this dissertation, three experiments using Josephson junction devices are described. In Part I, the effect of dissipation on tunneling between charge states in a superconducting single-electron transistor (sSET) was studied. The sSET was fabricated on top of a semi-conductor heterostructure with a two-dimensional electron gas (2DEG) imbedded beneath the surface. The 2DEG acted as a dissipative ground plane. The sheet resistance of the 2DEG could be varied in situ by applying a large voltage to a gate on the back of the substrate. The zero-bias conductance of the sSET was observed to increase with increasing temperature and 2DEG resistance. Some qualitative but not quantitative agreement was found with theoretical calculations of the functional dependence of the conductance on temperature and 2DEG resistance. Part II describes a series of experiments performed on magnesium diboride point-contact junctions. The pressure between the MgB2 tip and base pieces could be adjusted to form junctions with different characteristics. With light pressure applied between the two pieces, quasiparticle tunneling in superconductor-insulator-superconductor junctions was measured. From these data, a superconducting gap of approximately 2 meV and a critical temperature of 29 K were estimated. Increasing the pressure between the MgB2 pieces formed junctions with superconductor-normal metal-superconductor characteristics. We used these junctions to form MgB2 superconducting quantum interference devices (SQUIDS). Noise levels as low as 35 fT/Hz1/2 and 4 muphi 0/Hz1/2 at 1 kHz were measured. In Part III, we used a SQUID-based instrument to acquire magnetocardiograms (MCG), the magnetic field signal measured from the human heart. We measured 51 healthy volunteers and 11 cardiac patients both at rest and after treadmill exercise. We found age and sex related differences in the MCG of the healthy volunteers that suggest that these factors should be considered when evaluating the MCG for

  8. Microtesla magnetic resonance imaging with a superconducting quantum interference device

    SciTech Connect

    McDermott, Robert; Lee, SeungKyun; ten Haken, Bennie; Trabesinger, Andreas H.; Pines, Alexander; Clarke, John

    2004-03-15

    We have constructed a magnetic resonance imaging (MRI) scanner based on a dc Superconducting QUantum Interference Device (SQUID) configured as a second-derivative gradiometer. The magnetic field sensitivity of the detector is independent of frequency; it is therefore possible to obtain high-resolution images by prepolarizing the nuclear spins in a field of 300 mT and detecting the signal at 132 fYT, corresponding to a proton Larmor frequency of 5.6 kHz. The reduction in the measurement field by a factor of 10,000 compared with conventional scanners eliminates inhomogeneous broadening of the nuclear magnetic resonance lines, even in fields with relatively poor homogeneity. The narrow linewidths result in enhanced signal-to-noise ratio and spatial resolution for a fixed strength of the magnetic field gradients used to encode the image. We present two-dimensional images of phantoms and pepper slices, obtained in typical magnetic field gradients of 100 fYT/m, with a spatial resolution of about 1mm. We further demonstrate a slice-selected image of an intact pepper. By varying the time delay between removal of the polarizing field and initiation of the spin echo sequence we acquire T1-weighted contrast images of water phantoms, some of which are doped with a paramagnetic salt; here, T1 is the nuclear spin-lattice relaxation time. The techniques presented here could readily be adapted to existing multichannel SQUID systems used for magnetic source imaging of brain signals. Further potential applications include low-cost systems for tumor screening and imaging peripheral regions of the body.

  9. Microtesla MRI with a superconducting quantum interference device

    PubMed Central

    McDermott, Robert; Lee, SeungKyun; Haken, Bennie ten; Trabesinger, Andreas H.; Pines, Alexander; Clarke, John

    2004-01-01

    MRI scanners enable fast, noninvasive, and high-resolution imaging of organs and soft tissue. The images are reconstructed from NMR signals generated by nuclear spins that precess in a static magnetic field B0 in the presence of magnetic field gradients. Most clinical MRI scanners operate at a magnetic field B0 = 1.5 T, corresponding to a proton resonance frequency of 64 MHz. Because these systems rely on large superconducting magnets, they are costly and demanding of infrastructure. On the other hand, low-field imagers have the potential to be less expensive, less confining, and more mobile. The major obstacle is the intrinsically low sensitivity of the low-field NMR experiment. Here, we show that prepolarization of the nuclear spins and detection with a superconducting quantum interference device (SQUID) yield a signal that is independent of B0, allowing acquisition of high-resolution MRIs in microtesla fields. Reduction of the strength of the measurement field eliminates inhomogeneous broadening of the NMR lines, resulting in enhanced signal-to-noise ratio and spatial resolution for a fixed strength of the magnetic field gradients used to encode the image. We present high-resolution images of phantoms and other samples and T1-weighted contrast images acquired in highly inhomogeneous magnetic fields of 132 μT; here, T1 is the spin-lattice relaxation time. These techniques could readily be adapted to existing multichannel SQUID systems used for magnetic source imaging of brain signals. Further potential applications include low-cost systems for tumor screening and imaging peripheral regions of the body. PMID:15141077

  10. Direct measurement on the geometric phase of a double quantum dot qubit via quantum point contact device

    NASA Astrophysics Data System (ADS)

    Liu, Bao; Zhang, Feng-Yang; Song, Jie; Song, He-Shan

    2015-06-01

    We propose a direct measurement scheme to read out the geometric phase of a coupled double quantum dot system via a quantum point contact(QPC) device. An effective expression of the geometric phase has been derived, which relates the geometric phase of the double quantum dot qubit to the current through QPC device. All the parameters in our expression are measurable or tunable in experiment. Moreover, since the measurement process affects the state of the qubit slightly, the geometric phase can be protected. The feasibility of the scheme has been analyzed. Further, as an example, we simulate the geometrical phase of a qubit when the QPC device is replaced by a single electron transistor(SET).

  11. White Electroluminescent Lighting Device Based on a Single Quantum Dot Emitter.

    PubMed

    Kim, Jong-Hoon; Jo, Dae-Yeon; Lee, Ki-Heon; Jang, Eun-Pyo; Han, Chang-Yeol; Jo, Jung-Ho; Yang, Heesun

    2016-07-01

    Using a single emitter of Cu-Ga-S/ZnS quantum dots, all-solution-processed white electroluminescent lighting device that not only exhibits the record quantities of 1007 cd m(-2) in luminance and 1.9% in external quantum efficiency but also possesses satisfactorily high color rendering indices of 83-88 is demonstrated. PMID:27135303

  12. Advanced materials and concepts for energy storage devices

    NASA Astrophysics Data System (ADS)

    Teng, Shiang Jen

    Over the last decade, technological progress and advances in the miniaturization of electronic devices have increased demands for light-weight, high-efficiency, and carbon-free energy storage devices. These energy storage devices are expected to play important roles in automobiles, the military, power plants, and consumer electronics. Two main types of electrical energy storage systems studied in this research are Li ion batteries and supercapacitors. Several promising solid state electrolytes and supercapacitor electrode materials are investigated in this research. The first section of this dissertation is focused on the novel results on pulsed laser annealing of Li7La3Zr2O12 (LLZO). LLZO powders with a tetragonal structure were prepared by a sol-gel technique, then a pulsed laser annealing process was employed to convert the tetragonal powders to cubic LLZO without any loss of lithium. The second section of the dissertation reports on how Li5La 3Nb2O12 (LLNO) was successfully synthesized via a novel molten salt synthesis (MSS) method at the relatively low temperature of 900°C. The low sintering temperature prevented the loss of lithium that commonly occurs during synthesis using conventional solid state or wet chemical reactions. The second type of energy storage device studied is supercapacitors. Currently, research on supercapacitors is focused on increasing their energy densities and lowering their overall production costs by finding suitable electrode materials. The third section of this dissertation details how carbonized woods electrodes were used as supercapacitor electrode materials. A high energy density of 45.6 Wh/kg and a high power density of 2000 W/kg were obtained from the supercapacitor made from carbonized wood electrodes. The high performance of the supercapacitor was discovered to originate from the hierarchical porous structures of the carbonized wood. Finally, the fourth section of this dissertation is on the electrochemical effects of

  13. 76 FR 48169 - Advancing Regulatory Science for Highly Multiplexed Microbiology/Medical Countermeasure Devices...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-08

    ... Microbiology/ Medical Countermeasure Devices; Public Meeting AGENCY: Food and Drug Administration, HHS. ACTION... following public meeting: ``Advancing Regulatory Science for Highly Multiplexed Microbiology/Medical... multiplexed microbiology/medical countermeasure (MCM) devices, their clinical application and public...

  14. Lithography for enabling advances in integrated circuits and devices.

    PubMed

    Garner, C Michael

    2012-08-28

    Because the transistor was fabricated in volume, lithography has enabled the increase in density of devices and integrated circuits. With the invention of the integrated circuit, lithography enabled the integration of higher densities of field-effect transistors through evolutionary applications of optical lithography. In 1994, the semiconductor industry determined that continuing the increase in density transistors was increasingly difficult and required coordinated development of lithography and process capabilities. It established the US National Technology Roadmap for Semiconductors and this was expanded in 1999 to the International Technology Roadmap for Semiconductors to align multiple industries to provide the complex capabilities to continue increasing the density of integrated circuits to nanometre scales. Since the 1960s, lithography has become increasingly complex with the evolution from contact printers, to steppers, pattern reduction technology at i-line, 248 nm and 193 nm wavelengths, which required dramatic improvements of mask-making technology, photolithography printing and alignment capabilities and photoresist capabilities. At the same time, pattern transfer has evolved from wet etching of features, to plasma etch and more complex etching capabilities to fabricate features that are currently 32 nm in high-volume production. To continue increasing the density of devices and interconnects, new pattern transfer technologies will be needed with options for the future including extreme ultraviolet lithography, imprint technology and directed self-assembly. While complementary metal oxide semiconductors will continue to be extended for many years, these advanced pattern transfer technologies may enable development of novel memory and logic technologies based on different physical phenomena in the future to enhance and extend information processing. PMID:22802500

  15. Magnetic Microscopy Using a Superconducting Quantum Interference Device

    NASA Astrophysics Data System (ADS)

    Black, Randall Christopher

    1995-01-01

    I describe the design, development, and operation of two different scanning probe microscopes which use a dc superconducting quantum interference device (SQUID) as the sensor. Because of the unprecedented magnetic flux sensitivity of the SQUID, these microscopes can image spatial distributions of magnetic fields on a microscopic scale with an exceptional combination of spatial resolution (currently about 10 μm) and static magnetic field sensitivity (about 34 pT Hz^{ -1/2} at 100 Hz). Both microscopes use thin -film high transition-temperature YBa_2Cu _3O_7 SQUIDs. Unlike other SQUID -based techniques which detect weak magnetic fields by coupling a superconducting pickup-coil to the SQUID and using the SQUID as a current amplifier, the scanning SQUID microscopes described here use the loop of the SQUID directly as the sensor, thus achieving the maximum possible spatial resolution, flux sensitivity, and bandwidth. To achieve high spatial resolution, the SQUID must be correspondingly small and close to the surface of the sample being imaged. In the first instrument, the sample is immersed directly in the liquid nitrogen used to cool the SQUID. In the second microscope, a thin sapphire window in a close-spaced dewar allows the imaging of room -temperature samples in air with a spatial resolution as fine as 50 mum. In addition to using the microscope to image static magnetic fields, I developed three other imaging techniques which use the large detection bandwidth of the SQUID. Eddy currents which are induced in metallic samples by an alternating magnetic field can be imaged at frequencies up to about 1 MHz. Using the SQUID as a field rectifier, I am also able to image radio- and microwave-frequency magnetic fields produced by oscillating currents in samples. Finally, by using the oscillating microwave Josephson currents in the SQUID body, I can obtain voltage-tunable microwave eddy-current images of metallic sample up to about 200 GHz. To demonstrate the imaging

  16. A Security Proof of Measurement Device Independent Quantum Key Distribution: From the View of Information Theory

    NASA Astrophysics Data System (ADS)

    Li, Fang-Yi; Yin, Zhen-Qiang; Li, Hong-Wei; Chen, Wei; Wang, Shuang; Wen, Hao; Zhao, Yi-Bo; Han, Zheng-Fu

    2014-07-01

    Although some ideal quantum key distribution protocols have been proved to be secure, there have been some demonstrations that practical quantum key distribution implementations were hacked due to some real-life imperfections. Among these attacks, detector side channel attacks may be the most serious. Recently, a measurement device independent quantum key distribution protocol [Phys. Rev. Lett. 108 (2012) 130503] was proposed and all detector side channel attacks are removed in this scheme. Here a new security proof based on quantum information theory is given. The eavesdropper's information of the sifted key bits is bounded. Then with this bound, the final secure key bit rate can be obtained.

  17. Optical Biosensors: A Revolution Towards Quantum Nanoscale Electronics Device Fabrication

    PubMed Central

    Dey, D.; Goswami, T.

    2011-01-01

    The dimension of biomolecules is of few nanometers, so the biomolecular devices ought to be of that range so a better understanding about the performance of the electronic biomolecular devices can be obtained at nanoscale. Development of optical biomolecular device is a new move towards revolution of nano-bioelectronics. Optical biosensor is one of such nano-biomolecular devices that has a potential to pave a new dimension of research and device fabrication in the field of optical and biomedical fields. This paper is a very small report about optical biosensor and its development and importance in various fields. PMID:22131802

  18. Design of advanced ultrasonic transducers for welding devices.

    PubMed

    Parrini, L

    2001-11-01

    A new high frequency ultrasonic transducer has been conceived, designed, prototyped, and tested. In the design phase, an advanced approach was used and established. The method is based on an initial design estimate obtained with finite element method (FEM) simulations. The simulated ultrasonic transducers and resonators are then built and characterized experimentally through laser interferometry and electrical resonance spectra. The comparison of simulation results with experimental data allows the parameters of FEM models to be adjusted and optimized. The achieved FEM simulations exhibit a remarkably high predictive potential and allow full control of the vibration behavior of the transducer. The new transducer is mounted on a wire bonder with a flange whose special geometry was calculated by means of FEM simulations. This flange allows the transducer to be attached on the wire bonder, not only in longitudinal nodes, but also in radial nodes of the ultrasonic field excited in the horn. This leads to a total decoupling of the transducer to the wire bonder, which has not been achieved so far. The new approach to mount ultrasonic transducers on a welding device is of major importance, not only for wire bonding, but also for all high power ultrasound applications and has been patented. PMID:11800125

  19. Advanced, High Power, Next Scale, Wave Energy Conversion Device

    SciTech Connect

    Mekhiche, Mike; Dufera, Hiz; Montagna, Deb

    2012-10-29

    The project conducted under DOE contract DE‐EE0002649 is defined as the Advanced, High Power, Next Scale, Wave Energy Converter. The overall project is split into a seven‐stage, gated development program. The work conducted under the DOE contract is OPT Stage Gate III work and a portion of Stage Gate IV work of the seven stage product development process. The project effort includes Full Concept Design & Prototype Assembly Testing building on our existing PowerBuoy technology to deliver a device with much increased power delivery. Scaling‐up from 150kW to 500kW power generating capacity required changes in the PowerBuoy design that addressed cost reduction and mass manufacturing by implementing a Design for Manufacturing (DFM) approach. The design changes also focused on reducing PowerBuoy Installation, Operation and Maintenance (IO&M) costs which are essential to reducing the overall cost of energy. In this design, changes to the core PowerBuoy technology were implemented to increase capability and reduce both CAPEX and OPEX costs. OPT conceptually envisaged moving from a floating structure to a seabed structure. The design change from a floating structure to seabed structure would provide the implementation of stroke‐ unlimited Power Take‐Off (PTO) which has a potential to provide significant power delivery improvement and transform the wave energy industry if proven feasible.

  20. Hybrid entanglement in a triple-quantum-dot shuttle device

    NASA Astrophysics Data System (ADS)

    Mora, J.; Cota, E.; Rojas, F.

    2014-10-01

    We study the H3×N hybrid entanglement between charge and vibrational modes in a triple-quantum-dot shuttle system. Three quantum dots are linearly connected, with the outer dots fixed and the central dot oscillating, described as a quantum harmonic oscillator with oscillation modes that are entangled with the electronic states of the quantum dots. The entangled states are characterized by the Schmidt number as a function of the parameters of the system: detuning and inverse tunneling length. We show that at steady state, as a function of detuning, the excited states of lower energy present Bell-type entanglement 2×N, with the participation of two quantum dots, while the more energetic excited states present 3×N entanglement, with the participation of three quantum dots. In the stationary regime, we find qualitative relationships between the maxima of the electronic current and the Schmidt number. Also, the time evolution of the degree of entanglement for a particular initial condition is studied in the presence of a time-dependent electric field and we evaluate the effects on entanglement of the condition of coherent destruction of tunneling.

  1. Graphene Quantum Dots: Molecularly Designed, Nitrogen-Functionalized Graphene Quantum Dots for Optoelectronic Devices (Adv. Mater. 23/2016).

    PubMed

    Tetsuka, Hiroyuki; Nagoya, Akihiro; Fukusumi, Takanori; Matsui, Takayuki

    2016-06-01

    H. Tetsuka and co-workers develop a versatile technique to tune the energy levels and energy gaps of nitrogen-functionalized graphene quantum dots (NGQDs) continuously through molecular structure design, as described on page 4632. The incorporation of layers of NGQDs into the structures markedly improves the performance of optoelectronic devices. PMID:27281048

  2. Simulation of electron transport in quantum well devices

    NASA Technical Reports Server (NTRS)

    Miller, D. R.; Gullapalli, K. K.; Reddy, V. R.; Neikirk, D. P.

    1992-01-01

    Double barrier resonant tunneling diodes (DBRTD) have received much attention as possible terahertz devices. Despite impressive experimental results, the specifics of the device physics (i.e., how the electrons propagate through the structure) are only qualitatively understood. Therefore, better transport models are warranted if this technology is to mature. In this paper, the Lattice Wigner function is used to explain the important transport issues associated with DBRTD device behavior.

  3. Quantum devices in silicon/silicon germanium heterostructures

    NASA Astrophysics Data System (ADS)

    Slinker, Keith A.

    This thesis presents the fabrication and characterization of silicon/silicon-germanium quantum wells, quantum dots, and quantum point contacts. These systems are promising for quantum computing applications due to the long predicted spin lifetimes. In addition, the valley states in Si/SiGe two-dimensional electron gases (2DEGs) are a novel phenomenon in regards to nanostructures, and characterizing these states is also necessary for potential computing applications. However, working with these heterostructures---especially in regards to metal Schottky gating---has proved historically challenging such that single electron transistors had not been achieved at the onset of this research. The first quantum dots in Si/SiGe are presented, defined completely by CF4 reactive ion etch without the use of metal gates. Etch-defined 2DEG side gates are used to modulate the potential of the quantum dot. Results for various metal gating schemes are also presented, culminating in the first Schottky-gated quantum dots in Si/SiGe. Differing from the etch-defined dots, the tunnel junctions of the metal-etch hybrid dot are fully tunable by the voltage applied to the top gates. Hall measurements of multiple heterostructures are presented, providing evidence that many of the challenges associated with gating Si/SiGe can be attributed to undepleted dopants in the supply layer. These dopants screen the top gates but can be detected as a parallel conduction channel in Hall measurements taken at a 2 K. A fully top-gate defined quantum dot was fabricated on an optimized Si/SiGe heterostructure, and the single particle excited states were resolved for the first time in Si/SiGe. Finally, quantum point contacts were defined by metal top gates, and the conduction was mapped out over a large range of magnetic field and voltages on the gates. The positions of the conductance steps are used to extract the valley splitting---a quantity that had been measured in a bulk 2DEG but not in a nanostructure

  4. High speed switching in quantum Dot/Ti-TiOx nonvolatile memory device

    NASA Astrophysics Data System (ADS)

    Kannan, V.; Kim, Hyun-Seok; Park, Hyun-Chang

    2016-03-01

    We report a Ti-TiOx/CdSe-ZnS core-shell quantum dot based bipolar nonvolatile resistive memory device. The device exhibits an ON/OFF ratio of 100 and is reproducible. The memory device showed good retention characteristics under stress and excellent stability even after 100,000 cycles of switching operation. The switching speed measured was around 15 ns. The devices are solution processed at room temperature in ambient atmosphere. The operating mechanism is discussed based on charge trapping in quantum dots resulting in the Coulomb blockade effect with a ZnS shell layer and metal-oxide layer acting as the barrier to confine the trapped charges. The proposed mechanism is validated by a three terminal device designed exclusively for this purpose. [Figure not available: see fulltext.

  5. Point-of-care (POC) devices by means of advanced MEMS.

    PubMed

    Karsten, Stanislav L; Tarhan, Mehmet C; Kudo, Lili C; Collard, Dominique; Fujita, Hiroyuki

    2015-12-01

    Microelectromechanical systems (MEMS) have become an invaluable technology to advance the development of point-of-care (POC) devices for diagnostics and sample analyses. MEMS can transform sophisticated methods into compact and cost-effective microdevices that offer numerous advantages at many levels. Such devices include microchannels, microsensors, etc., that have been applied to various miniaturized POC products. Here we discuss some of the recent advances made in the use of MEMS devices for POC applications. PMID:26459443

  6. Plug-and-play measurement-device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Choi, Yujun; Kwon, Osung; Woo, Minki; Oh, Kyunghwan; Han, Sang-Wook; Kim, Yong-Su; Moon, Sung

    2016-03-01

    Quantum key distribution (QKD) guarantees unconditional communication security based on the laws of quantum physics. However, practical QKD suffers from a number of quantum hackings due to the device imperfections. From the security standpoint, measurement-device-independent quantum key distribution (MDI-QKD) is in the limelight since it eliminates all the possible loopholes in detection. Due to active control units for mode matching between the photons from remote parties, however, the implementation of MDI-QKD is highly impractical. In this paper, we propose a method to resolve the mode matching problem while minimizing the use of active control units. By introducing the plug-and-play (P&P) concept into MDI-QKD, the indistinguishability in spectral and polarization modes between photons can naturally be guaranteed. We show the feasibility of P&P MDI-QKD with a proof-of-principle experiment.

  7. W-state Analyzer and Multi-party Measurement-device-independent Quantum Key Distribution

    NASA Astrophysics Data System (ADS)

    Zhu, Changhua; Xu, Feihu; Pei, Changxing

    2015-12-01

    W-state is an important resource for many quantum information processing tasks. In this paper, we for the first time propose a multi-party measurement-device-independent quantum key distribution (MDI-QKD) protocol based on W-state. With linear optics, we design a W-state analyzer in order to distinguish the four-qubit W-state. This analyzer constructs the measurement device for four-party MDI-QKD. Moreover, we derived a complete security proof of the four-party MDI-QKD, and performed a numerical simulation to study its performance. The results show that four-party MDI-QKD is feasible over 150 km standard telecom fiber with off-the-shelf single photon detectors. This work takes an important step towards multi-party quantum communication and a quantum network.

  8. W-state Analyzer and Multi-party Measurement-device-independent Quantum Key Distribution.

    PubMed

    Zhu, Changhua; Xu, Feihu; Pei, Changxing

    2015-01-01

    W-state is an important resource for many quantum information processing tasks. In this paper, we for the first time propose a multi-party measurement-device-independent quantum key distribution (MDI-QKD) protocol based on W-state. With linear optics, we design a W-state analyzer in order to distinguish the four-qubit W-state. This analyzer constructs the measurement device for four-party MDI-QKD. Moreover, we derived a complete security proof of the four-party MDI-QKD, and performed a numerical simulation to study its performance. The results show that four-party MDI-QKD is feasible over 150 km standard telecom fiber with off-the-shelf single photon detectors. This work takes an important step towards multi-party quantum communication and a quantum network. PMID:26644289

  9. W-state Analyzer and Multi-party Measurement-device-independent Quantum Key Distribution

    PubMed Central

    Zhu, Changhua; Xu, Feihu; Pei, Changxing

    2015-01-01

    W-state is an important resource for many quantum information processing tasks. In this paper, we for the first time propose a multi-party measurement-device-independent quantum key distribution (MDI-QKD) protocol based on W-state. With linear optics, we design a W-state analyzer in order to distinguish the four-qubit W-state. This analyzer constructs the measurement device for four-party MDI-QKD. Moreover, we derived a complete security proof of the four-party MDI-QKD, and performed a numerical simulation to study its performance. The results show that four-party MDI-QKD is feasible over 150 km standard telecom fiber with off-the-shelf single photon detectors. This work takes an important step towards multi-party quantum communication and a quantum network. PMID:26644289

  10. Quantum 1/f noise in high technology applications including ultrasmall structures and devices

    NASA Astrophysics Data System (ADS)

    Handel, Peter H.

    1994-05-01

    The present report brings a final answer to the question on the nature of fundamental 1/f noise and its ubiquity. A sufficient criterion for a 1/f spectrum in arbitrary chaotic nonlinear systems is derived for the first time. This criterion guarantees a 1/f spectrum for nonlinear systems which also satisfy a condition of mathematical homogeneity. Briefly stated, nonlinearity + homogeneity = 1/f noise. The criterion results because the 1/f spectrum reproduces itself in a self-convolution. Among the five examples to which the criterion is applied is also quantum electrodynamics (QED), resulting in quantum 1/f noise as a fundamental form of quantum chaos. Nonlinearity of the system of a charged particle and its field, plus the basic homogeneity of physical equations causes the criterion to predict the quantum 1/f effect. The simple universal quantum 1/f formula is applied to infrared detectors and yields quantum 1/f noise in the dark current, but not in the photogenerated current. The fractal dimension of quantum 1/f noise is determined on the basis of its quantum chaos definition and is obtained theoretically as a function of bandwidth in a simple model by applying the Grassberger-Procaccia-Takens algorithm to the quantum 1/f theory. The quantum 1/f effect is successfully applied to quartz resonators and bipolar junction transistors. Finally, the quantum 1/f mobility fluctuations are calculated in silicon and the coherent quantum 1/f effect is derived for the first time from a new QED propagator with branch-point singularity. This opens the way to better bridging the gap between coherent and conventional quantum 1/f noise in small and ultrasmall devices.

  11. Implementing an ancilla-free 1{yields}M economical phase-covariant quantum cloning machine with superconducting quantum-interference devices in cavity QED

    SciTech Connect

    Yu Longbao; Ye Liu; Zhang Wenhai

    2007-09-15

    We propose a simple scheme to realize 1{yields}M economical phase-covariant quantum cloning machine (EPQCM) with superconducting quantum interference device (SQUID) qubits. In our scheme, multi-SQUIDs are fixed into a microwave cavity by adiabatic passage for their manipulation. Based on this model, we can realize the EPQCM with high fidelity via adiabatic quantum computation.

  12. N-dimensional measurement-device-independent quantum key distribution with N + 1 un-characterized sources: zero quantum-bit-error-rate case

    NASA Astrophysics Data System (ADS)

    Hwang, Won-Young; Su, Hong-Yi; Bae, Joonwoo

    2016-07-01

    We study N-dimensional measurement-device-independent quantum-key-distribution protocol where one checking state is used. Only assuming that the checking state is a superposition of other N sources, we show that the protocol is secure in zero quantum-bit-error-rate case, suggesting possibility of the protocol. The method may be applied in other quantum information processing.

  13. Carrier multiplication detected through transient photocurrent in device-grade films of lead selenide quantum dots

    PubMed Central

    Gao, Jianbo; Fidler, Andrew F.; Klimov, Victor I.

    2015-01-01

    In carrier multiplication, the absorption of a single photon results in two or more electron–hole pairs. Quantum dots are promising materials for implementing carrier multiplication principles in real-life technologies. So far, however, most of research in this area has focused on optical studies of solution samples with yet to be proven relevance to practical devices. Here we report ultrafast electro-optical studies of device-grade films of electronically coupled quantum dots that allow us to observe multiplication directly in the photocurrent. Our studies help rationalize previous results from both optical spectroscopy and steady-state photocurrent measurements and also provide new insights into effects of electric field and ligand treatments on multiexciton yields. Importantly, we demonstrate that using appropriate chemical treatments of the films, extra charges produced by carrier multiplication can be extracted from the quantum dots before they are lost to Auger recombination and hence can contribute to photocurrent of practical devices. PMID:26345390

  14. Carrier multiplication detected through transient photocurrent in device-grade films of lead selenide quantum dots

    SciTech Connect

    Gao, Jianbo; Fidler, Andrew F.; Klimov, Victor I.

    2015-09-08

    In carrier multiplication, the absorption of a single photon results in two or more electron–hole pairs. Quantum dots are promising materials for implementing carrier multiplication principles in real-life technologies. So far, however, most of research in this area has focused on optical studies of solution samples with yet to be proven relevance to practical devices. We report ultra-fast electro-optical studies of device-grade films of electronically coupled quantum dots that allow us to observe multiplication directly in the photocurrent. Our studies help rationalize previous results from both optical spectroscopy and steady-state photocurrent measurements and also provide new insights into effects of electric field and ligand treatments on multiexciton yields. Importantly, we demonstrate that using appropriate chemical treatments of the films, extra charges produced by carrier multiplication can be extracted from the quantum dots before they are lost to Auger recombination and hence can contribute to photocurrent of practical devices.

  15. A Transfer Hamiltonian Model for Devices Based on Quantum Dot Arrays

    PubMed Central

    Illera, S.; Prades, J. D.; Cirera, A.; Cornet, A.

    2015-01-01

    We present a model of electron transport through a random distribution of interacting quantum dots embedded in a dielectric matrix to simulate realistic devices. The method underlying the model depends only on fundamental parameters of the system and it is based on the Transfer Hamiltonian approach. A set of noncoherent rate equations can be written and the interaction between the quantum dots and between the quantum dots and the electrodes is introduced by transition rates and capacitive couplings. A realistic modelization of the capacitive couplings, the transmission coefficients, the electron/hole tunneling currents, and the density of states of each quantum dot have been taken into account. The effects of the local potential are computed within the self-consistent field regime. While the description of the theoretical framework is kept as general as possible, two specific prototypical devices, an arbitrary array of quantum dots embedded in a matrix insulator and a transistor device based on quantum dots, are used to illustrate the kind of unique insight that numerical simulations based on the theory are able to provide. PMID:25879055

  16. Fabrication and characterization of an undoped GaAs/AlGaAs quantum dot device

    SciTech Connect

    Li, Hai-Ou; Cao, Gang; Xiao, Ming You, Jie; Wei, Da; Tu, Tao; Guo, Guang-Can; Guo, Guo-Ping; Jiang, Hong-Wen

    2014-11-07

    We demonstrate the development of a double quantum dot with an integrated charge sensor fabricated in undoped GaAs/AlGaAs heterostructures using a double top-gated design. Based on the evaluation of the integrated charge sensor, the double quantum dot can be tuned to a few-electron region. Additionally, the inter-dot coupling of the double quantum dot can be tuned to a large extent according to the voltage on the middle gate. The quantum dot is shown to be tunable from a single dot to a well-isolated double dot. To assess the stability of such design, the potential fluctuation induced by 1/f noise was measured. Based on the findings herein, the quantum dot design developed in the undoped GaAs/AlGaAs semiconductor shows potential for the future exploitation of nano-devices.

  17. Gaussian-modulated coherent-state measurement-device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Ma, Xiang-Chun; Sun, Shi-Hai; Jiang, Mu-Sheng; Gui, Ming; Liang, Lin-Mei

    2014-04-01

    Measurement-device-independent quantum key distribution (MDI-QKD), leaving the detection procedure to the third partner and thus being immune to all detector side-channel attacks, is very promising for the construction of high-security quantum information networks. We propose a scheme to implement MDI-QKD, but with continuous variables instead of discrete ones, i.e., with the source of Gaussian-modulated coherent states, based on the principle of continuous-variable entanglement swapping. This protocol not only can be implemented with current telecom components but also has high key rates compared to its discrete counterpart; thus it will be highly compatible with quantum networks.

  18. Enhancement of Quantum Efficiency of Organic Light Emitting Devices by Doping Magnetic Nanoparticles

    SciTech Connect

    Sun, Chengjun; Wu, Yue; Xu, Zhihua; Hu, Bin; Bai, Jianmin; Wang, Jian-Ping; Shen, Jian

    2007-01-01

    Magnetic nanoparticles of CoFe are used as dopants to enhance the quantum efficiency of electroluminance in a single layer organic light emitting device (OLED). The enhancement of quantum efficiency increases with both increasing density of CoFe nanoparticles and external magnetic field. For a given OLED with 0.1 wt % doping, the enhancement of the quantum efficiency reaches {approx}27% and {approx}32% without and with a magnetic field, respectively. The origin of these improvements could be attributed to the simultaneous increases of the portion of excitons among total charge carriers and the fraction of singlets among the total excitons

  19. Long-distance quantum key distribution with imperfect devices

    SciTech Connect

    Lo Piparo, Nicoló; Razavi, Mohsen

    2014-12-04

    Quantum key distribution over probabilistic quantum repeaters is addressed. We compare, under practical assumptions, two such schemes in terms of their secure key generation rate per memory, R{sub QKD}. The two schemes under investigation are the one proposed by Duan et al. in [Nat. 414, 413 (2001)] and that of Sangouard et al. proposed in [Phys. Rev. A 76, 050301 (2007)]. We consider various sources of imperfections in the latter protocol, such as a nonzero double-photon probability for the source, dark count per pulse, channel loss and inefficiencies in photodetectors and memories, to find the rate for different nesting levels. We determine the maximum value of the double-photon probability beyond which it is not possible to share a secret key anymore. We find the crossover distance for up to three nesting levels. We finally compare the two protocols.

  20. Hybrid Quantum Device with Nitrogen-Vacancy Centers in Diamond Coupled to Carbon Nanotubes

    NASA Astrophysics Data System (ADS)

    Li, Peng-Bo; Xiang, Ze-Liang; Rabl, Peter; Nori, Franco

    2016-07-01

    We show that nitrogen-vacancy (NV) centers in diamond interfaced with a suspended carbon nanotube carrying a dc current can facilitate a spin-nanomechanical hybrid device. We demonstrate that strong magnetomechanical interactions between a single NV spin and the vibrational mode of the suspended nanotube can be engineered and dynamically tuned by external control over the system parameters. This spin-nanomechanical setup with strong, intrinsic, and tunable magnetomechanical couplings allows for the construction of hybrid quantum devices with NV centers and carbon-based nanostructures, as well as phonon-mediated quantum information processing with spin qubits.

  1. Electrode-stress-induced nanoscale disorder in Si quantum electronic devices

    NASA Astrophysics Data System (ADS)

    Park, J.; Ahn, Y.; Tilka, J. A.; Sampson, K. C.; Savage, D. E.; Prance, J. R.; Simmons, C. B.; Lagally, M. G.; Coppersmith, S. N.; Eriksson, M. A.; Holt, M. V.; Evans, P. G.

    2016-06-01

    Disorder in the potential-energy landscape presents a major obstacle to the more rapid development of semiconductor quantum device technologies. We report a large-magnitude source of disorder, beyond commonly considered unintentional background doping or fixed charge in oxide layers: nanoscale strain fields induced by residual stresses in nanopatterned metal gates. Quantitative analysis of synchrotron coherent hard x-ray nanobeam diffraction patterns reveals gate-induced curvature and strains up to 0.03% in a buried Si quantum well within a Si/SiGe heterostructure. Electrode stress presents both challenges to the design of devices and opportunities associated with the lateral manipulation of electronic energy levels.

  2. Hybrid Quantum Device with Nitrogen-Vacancy Centers in Diamond Coupled to Carbon Nanotubes.

    PubMed

    Li, Peng-Bo; Xiang, Ze-Liang; Rabl, Peter; Nori, Franco

    2016-07-01

    We show that nitrogen-vacancy (NV) centers in diamond interfaced with a suspended carbon nanotube carrying a dc current can facilitate a spin-nanomechanical hybrid device. We demonstrate that strong magnetomechanical interactions between a single NV spin and the vibrational mode of the suspended nanotube can be engineered and dynamically tuned by external control over the system parameters. This spin-nanomechanical setup with strong, intrinsic, and tunable magnetomechanical couplings allows for the construction of hybrid quantum devices with NV centers and carbon-based nanostructures, as well as phonon-mediated quantum information processing with spin qubits. PMID:27419577

  3. A non-doped phosphorescent organic light-emitting device with above 31% external quantum efficiency.

    PubMed

    Wang, Qi; Oswald, Iain W H; Yang, Xiaolong; Zhou, Guijiang; Jia, Huiping; Qiao, Qiquan; Chen, Yonghua; Hoshikawa-Halbert, Jason; Gnade, Bruce E

    2014-12-23

    The demonstrated square-planar Pt(II)-complex has reduced triplet-triplet quenching and therefore a near unity quantum yield in the neat thin film. A non-doped phosphorescent organic light-emitting diode (PhOLED) based on this emitter achieves (31.1 ± 0.1)% external quantum efficiency without any out-coupling, which shows that a non-doped PhOLED can be comparable in efficiency to the best doped devices with very complicated device structures. PMID:25219957

  4. Long-distance quantum key distribution with imperfect devices

    NASA Astrophysics Data System (ADS)

    Lo Piparo, Nicoló; Razavi, Mohsen

    2013-07-01

    Quantum key distribution over probabilistic quantum repeaters is addressed. We compare, under practical assumptions, two such schemes in terms of their secret key generation rates per quantum memory. The two schemes under investigation are the one proposed by Duan [Nature (London)0028-083610.1038/35106500 414, 413 (2001)] and that of Sangouard [Phys. Rev. A1050-294710.1103/PhysRevA.76.050301 76, 050301 (2007)]. We consider various sources of imperfection in both protocols, such as nonzero double-photon probabilities at the sources, dark counts in detectors, and inefficiencies in the channel, photodetectors, and memories. We also consider memory decay and dephasing processes in our analysis. For the latter system, we determine the maximum value of the double-photon probability beyond which secret key distillation is not possible. We also find crossover distances for one nesting level to its subsequent one. We finally compare the two protocols in terms of their achievable secret key generation rates at their optimal settings. Our results specify regimes of operation where one system outperforms the other.

  5. Advanced methods for controlling untethered magnetic devices using rotating magnetic fields

    NASA Astrophysics Data System (ADS)

    Mahoney, Arthur W., Jr.

    This dissertation presents results documenting advancements on the control of untethered magnetic devices, such as magnetic "microrobots" and magnetically actuated capsule endoscopes, motivated by problems in minimally invasive medicine. This dissertation focuses on applying rotating magnetic fields for magnetic manipulation. The contributions include advancements in the way that helical microswimmers (devices that mimic the propulsion of bacterial flagella) are controlled in the presence of gravitational forces, advancements in ways that groups of untethered magnetic devices can be differentiated and semi-independently controlled, advancements in the way that untethered magnetic device can be controlled with a single rotating permanent magnet, and an improved understanding in the nature of the magnetic force applied to an untethered device by a rotating magnet.

  6. Natural Framework for Device-Independent Quantification of Quantum Steerability, Measurement Incompatibility, and Self-Testing

    NASA Astrophysics Data System (ADS)

    Chen, Shin-Liang; Budroni, Costantino; Liang, Yeong-Cherng; Chen, Yueh-Nan

    2016-06-01

    We introduce the concept of assemblage moment matrices, i.e., a collection of matrices of expectation values, each associated with a conditional quantum state obtained in a steering experiment. We demonstrate how it can be used for quantum states and measurements characterization in a device-independent manner, i.e., without invoking any assumption about the measurement or the preparation device. Specifically, we show how the method can be used to lower bound the steerability of an underlying quantum state directly from the observed correlation between measurement outcomes. Combining such device-independent quantifications with earlier results established by Piani and Watrous [Phys. Rev. Lett. 114, 060404 (2015)], our approach immediately provides a device-independent lower bound on the generalized robustness of entanglement, as well as the usefulness of the underlying quantum state for a type of subchannel discrimination problem. In addition, by proving a quantitative relationship between steering robustness and the recently introduced incompatibility robustness, our approach also allows for a device-independent quantification of the incompatibility between various measurements performed in a Bell-type experiment. Explicit examples where such bounds provide a kind of self-testing of the performed measurements are provided.

  7. Natural Framework for Device-Independent Quantification of Quantum Steerability, Measurement Incompatibility, and Self-Testing.

    PubMed

    Chen, Shin-Liang; Budroni, Costantino; Liang, Yeong-Cherng; Chen, Yueh-Nan

    2016-06-17

    We introduce the concept of assemblage moment matrices, i.e., a collection of matrices of expectation values, each associated with a conditional quantum state obtained in a steering experiment. We demonstrate how it can be used for quantum states and measurements characterization in a device-independent manner, i.e., without invoking any assumption about the measurement or the preparation device. Specifically, we show how the method can be used to lower bound the steerability of an underlying quantum state directly from the observed correlation between measurement outcomes. Combining such device-independent quantifications with earlier results established by Piani and Watrous [Phys. Rev. Lett. 114, 060404 (2015)], our approach immediately provides a device-independent lower bound on the generalized robustness of entanglement, as well as the usefulness of the underlying quantum state for a type of subchannel discrimination problem. In addition, by proving a quantitative relationship between steering robustness and the recently introduced incompatibility robustness, our approach also allows for a device-independent quantification of the incompatibility between various measurements performed in a Bell-type experiment. Explicit examples where such bounds provide a kind of self-testing of the performed measurements are provided. PMID:27367365

  8. Scaling in the quantum Hall regime of graphene Corbino devices

    SciTech Connect

    Peters, Eva C.; Burghard, Marko; Giesbers, A. J. M.; Kern, Klaus

    2014-05-19

    The scaling behavior of graphene devices in Corbino geometry was investigated through temperature dependent conductivity measurements under magnetic field. Evaluation of the Landau level width as a function of temperature yielded a relatively low temperature exponent of κ = 0.16 ± 0.05. Furthermore, an unusually large value close to 7.6 ± 0.9 was found for the universal scaling constant γ, while the determined inelastic scattering exponent of p = 2 is consistent with established scattering mechanisms in graphene. The deviation of the scaling parameters from values characteristic of conventional two-dimensional electron gases is attributed to an inhomogeneous charge carrier distribution in the Corbino devices. Direct evidence for the presence of the latter could be gained by spatially resolved photocurrent microscopy away from the charge neutrality point of the devices.

  9. Semi-device-independent security of one-way quantum key distribution

    SciTech Connect

    Pawlowski, Marcin; Brunner, Nicolas

    2011-07-15

    By testing nonlocality, the security of entanglement-based quantum key distribution (QKD) can be enhanced to being ''device-independent.'' Here we ask whether such a strong form of security could also be established for one-way (prepare and measure) QKD. While fully device-independent security is impossible, we show that security can be guaranteed against individual attacks in a semi-device-independent scenario. In the latter, the devices used by the trusted parties are noncharacterized, but the dimensionality of the quantum systems used in the protocol is assumed to be bounded. Our security proof relies on the analogies between one-way QKD, dimension witnesses, and random-access codes.

  10. Multi-valley effective mass theory for device-level modeling of open quantum dynamics

    NASA Astrophysics Data System (ADS)

    Jacobson, N. Tobias; Baczewski, Andrew D.; Frees, Adam; Gamble, John King; Montano, Ines; Moussa, Jonathan E.; Muller, Richard P.; Nielsen, Erik

    2015-03-01

    Simple models for semiconductor-based quantum information processors can provide useful qualitative descriptions of device behavior. However, as experimental implementations have matured, more specific guidance from theory has become necessary, particularly in the form of quantitatively reliable yet computationally efficient modeling. Besides modeling static device properties, improved characterization of noisy gate operations requires a more sophisticated description of device dynamics. Making use of recent developments in multi-valley effective mass theory, we discuss device-level simulations of the open system quantum dynamics of a qubit interacting with phonons and other noise sources. Sandia is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the US Department of Energy National Nuclear Security Administration under Contract No. DE-AC04-94AL85000.

  11. Design and Implementation of Quantum Dot Enhanced Next Generation Photovoltaic Devices

    NASA Astrophysics Data System (ADS)

    Polly, Stephen Jade

    Photovoltaics are an essential enabling technology providing power both where it would be impractical to deliver otherwise and where sustainably produced--and recently, economically competitive--energy is demanded. Significant effort has gone into increasing the efficiency of these devices since their initial development in the 1950s. The most dramatic enhancements have been from the judicious choice of material used for photon collection, with current state of the art (SOA) conversion efficiencies reaching 46%. Further improvements may be engineered through exploration of next-generation methodologies, such as the incorporation of quantum dots (QDs), to maximally exploit the solar spectrum and develop solar cells producing both large current densities and large voltages compared to current SOA. In this work, the electrical, optical, and mechanical properties of GaAs solar cells incorporating nanostructured InAs QDs, strain balanced with GaP, were studied. QDs allow for an increase in the current generation capabilities of the bulk GaAs semiconductor through absorption of sub-bandgap photons via bound states in the low-bandgap, low-dimensional material. QDs alter the recombination dynamics of charge carriers in the photovoltaic device, which typically led to an undesirable reduction in voltage of more than 200 mV. The addition of dopant, necessary to explore the effects of an intermediate band solar cell, showed a voltage recovery of 121 mV, with no positive or negative effects on sub-bandgap collection. Advanced characterization and data analysis techniques were developed, combining photoreflectance and temperature-dependent photoluminescence, to investigate the activation energy of bound states in the QD, which were shown to undesirably decrease by 34 meV to 40 meV with the addition of doping. Simulation of alternative structures that may help to increase this activation energy were performed using alternative strain balancing designs, and a general strain

  12. Superconducting quantum interference devices based set-up for probing current noise and correlations in three-terminal devices.

    PubMed

    Pfeffer, A H; Kaviraj, B; Coupiac, O; Lefloch, F

    2012-11-01

    We have implemented a new experimental set-up for precise measurements of current fluctuations in three-terminal devices. The system operates at very low temperatures (30 mK) and is equipped with three superconducting quantum interference devices (SQUIDs) as low noise current amplifiers. A SQUID input coil is connected to each terminal of a sample allowing the acquisition of time-dependent current everywhere in the circuit. From these traces, we can measure the current mean value, the noise, and cross-correlations between different branches of a device. In this paper, we present calibration results of noise and cross-correlations obtained using low impedance macroscopic resistors. From these results, we can extract the noise level of the set-up and show that there are no intrinsic correlations due to the measurement scheme. We also studied noise and correlations as a function of a dc current and estimated the electronic temperature of various macroscopic resistors. PMID:23206098

  13. Superconducting quantum interference devices based set-up for probing current noise and correlations in three-terminal devices

    SciTech Connect

    Pfeffer, A. H.; Kaviraj, B.; Coupiac, O.; Lefloch, F.

    2012-11-15

    We have implemented a new experimental set-up for precise measurements of current fluctuations in three-terminal devices. The system operates at very low temperatures (30 mK) and is equipped with three superconducting quantum interference devices (SQUIDs) as low noise current amplifiers. A SQUID input coil is connected to each terminal of a sample allowing the acquisition of time-dependent current everywhere in the circuit. From these traces, we can measure the current mean value, the noise, and cross-correlations between different branches of a device. In this paper, we present calibration results of noise and cross-correlations obtained using low impedance macroscopic resistors. From these results, we can extract the noise level of the set-up and show that there are no intrinsic correlations due to the measurement scheme. We also studied noise and correlations as a function of a dc current and estimated the electronic temperature of various macroscopic resistors.

  14. Large scale two-dimensional arrays of magnesium diboride superconducting quantum interference devices

    SciTech Connect

    Cybart, Shane A. Dynes, R. C.; Wong, T. J.; Cho, E. Y.; Beeman, J. W.; Yung, C. S.; Moeckly, B. H.

    2014-05-05

    Magnetic field sensors based on two-dimensional arrays of superconducting quantum interference devices were constructed from magnesium diboride thin films. Each array contained over 30 000 Josephson junctions fabricated by ion damage of 30 nm weak links through an implant mask defined by nano-lithography. Current-biased devices exhibited very large voltage modulation as a function of magnetic field, with amplitudes as high as 8 mV.

  15. Large scale two-dimensional arrays of magnesium diboride superconducting quantum interference devices

    NASA Astrophysics Data System (ADS)

    Cybart, Shane A.; Wong, T. J.; Cho, E. Y.; Beeman, J. W.; Yung, C. S.; Moeckly, B. H.; Dynes, R. C.

    2014-05-01

    Magnetic field sensors based on two-dimensional arrays of superconducting quantum interference devices were constructed from magnesium diboride thin films. Each array contained over 30 000 Josephson junctions fabricated by ion damage of 30 nm weak links through an implant mask defined by nano-lithography. Current-biased devices exhibited very large voltage modulation as a function of magnetic field, with amplitudes as high as 8 mV.

  16. Advanced, High Power, Next Scale, Wave Energy Conversion Device

    SciTech Connect

    Hart, Philip R.

    2011-09-27

    This presentation from the Water Peer Review highlights one of the program's marine and hyrokinetics device design projects to scale up the current Ocean Power Technology PowerBuoy from 150kW to 500kW.

  17. Advanced integrated safeguards using front-end-triggering devices

    SciTech Connect

    Howell, J.A.; Whitty, W.J.

    1995-12-01

    This report addresses potential uses of front-end-triggering devices for enhanced safeguards. Such systems incorporate video surveillance as well as radiation and other sensors. Also covered in the report are integration issues and analysis techniques.

  18. HeartWare left ventricular assist device for the treatment of advanced heart failure.

    PubMed

    Hanke, Jasmin S; Rojas, Sebastian V; Avsar, Murat; Bara, Christoph; Ismail, Issam; Haverich, Axel; Schmitto, Jan D

    2016-01-01

    The importance of mechanical circulatory support in the therapy of advanced heart failure is steadily growing. The rapid developments in the field of mechanical support are characterized by continuous miniaturization and enhanced performance of the assist devices, providing increased pump durability and prolonged patient survival. The HeartWare left ventricular assist device system (HeartWare Inc., Framingham, MA, USA) is a mechanical ventricular assist device with over 8000 implantations worldwide. Compared with other available assist devices it is smaller in size and used in a broad range of patients. The possibility of minimally invasive procedures is one of the major benefits of the device - allowing implants and explants, as well as exchanges of the device with reduced surgical impact. We present here a review of the existing literature on the treatment of advanced heart failure using the HeartWare left ventricular assist device system. PMID:26597386

  19. Fault-tolerance and thermal characteristics of quantum-dot cellular automata devices

    NASA Astrophysics Data System (ADS)

    Anduwan, G. A.; Padgett, B. D.; Kuntzman, M.; Hendrichsen, M. K.; Sturzu, I.; Khatun, M.; Tougaw, P. D.

    2010-06-01

    We present fault tolerant properties of various quantum-dot cellular automata (QCA) devices. Effects of temperatures and dot displacements on the operation of the fundamental devices such as a binary wire, logical gates, a crossover, and an exclusive OR (XOR) have been investigated. A Hubbard-type Hamiltonian and intercellular Hartree approximation have been used for modeling, and a uniform random distribution has been implemented for the defect simulations. The breakdown characteristics of all the devices are almost the same except the crossover. Results show that the success of any device is significantly dependent on both the fabrication defects and temperatures. We have observed unique characteristic features of the crossover. It is highly sensitive to defects of any magnitude. Results show that the presence of a crossover in a XOR design is a major factor for its failure. The effects of temperature and defects in the crossover device are pronounced and have significant impact on larger and complicated QCA devices.

  20. Atomic-scale investigations of current and future devices: from nitride-based transistors to quantum computing

    NASA Astrophysics Data System (ADS)

    Gordon, Luke

    Our era is defined by its technology, and our future is dependent on its continued evolution. Over the past few decades, we have witnessed the expansion of advanced technology into all walks of life and all industries, driven by the exponential increase in the speed and power of semiconductor-based devices. However, as the length scale of devices reaches the atomic scale, a deep understanding of atomistic theory and its application is increasingly crucial. In order to illustrate the power of an atomistic approach to understanding devices, we will present results and conclusions from three interlinked projects: n-type doping of III-nitride semiconductors, defects for quantum computing, and macroscopic simulations of devices. First, we will study effective n-type doping of III-nitride semiconductors and their alloys, and analyze the barriers to effective n-type doping of III-nitrides and their alloys. In particular, we will study the formation of DX centers, and predict alloy composition onsets for various III-nitride alloys. In addition, we will perform a comprehensive study of alternative dopants, and provide potential alternative dopants to improve n-type conductivity in AlN and wide-band-gap nitride alloys. Next, we will discuss how atomic-scale defects can act as a curse for the development of quantum computers by contributing to decoherence at an atomic scale, specifically investigating the effect of two-level state defects (TLS) systems in alumina as a source of decoherence in superconducting qubits based on Josephson junctions; and also as a blessing, by allowing the identification of wholly new qubits in different materials, specifically showing calculations on defects in SiC for quantum computing applications. Finally, we will provide examples of recent calculations we have performed for devices using macrosopic device simulations, largely in conjunction with first-principles calculations. Specifically, we will discuss the power of using a multi

  1. Highly entangled photons from hybrid piezoelectric-semiconductor quantum dot devices.

    PubMed

    Trotta, Rinaldo; Wildmann, Johannes S; Zallo, Eugenio; Schmidt, Oliver G; Rastelli, Armando

    2014-06-11

    Entanglement resources are key ingredients of future quantum technologies. If they could be efficiently integrated into a semiconductor platform, a new generation of devices could be envisioned, whose quantum-mechanical functionalities are controlled via the mature semiconductor technology. Epitaxial quantum dots (QDs) embedded in diodes would embody such ideal quantum devices, but a fine-structure splitting (FSS) between the bright exciton states lowers dramatically the degree of entanglement of the sources and hampers severely their real exploitation in the foreseen applications. In this work, we overcome this hurdle using strain-tunable optoelectronic devices, where any QD can be tuned for the emission of photon pairs featuring the highest degree of entanglement ever reported for QDs, with concurrence as high as 0.75 ± 0.02. Furthermore, we study the evolution of Bell's parameters as a function of FSS and demonstrate for the first time that filtering-free violation of Bell's inequalities requires the FSS to be smaller than 1 μeV. This upper limit for the FSS also sets the tuning range of exciton energies (∼1 meV) over which our device operates as an energy-tunable source of highly entangled photons. A moderate temporal filtering further increases the concurrence and the tunability of exciton energies up to 0.82 and 2 meV, respectively, though at the expense of 60% reduction of count rate. PMID:24845369

  2. Molecularly Designed, Nitrogen-Functionalized Graphene Quantum Dots for Optoelectronic Devices.

    PubMed

    Tetsuka, Hiroyuki; Nagoya, Akihiro; Fukusumi, Takanori; Matsui, Takayuki

    2016-06-01

    Nitrogen-functionalized graphene quantum dots (NGQDs) with tailorable optical properties are prepared by a versatile technique, which allows the highest occupied molecular orbital/lowest unoccupied molecular orbital energy levels and energy gaps to be continuously varied. The integration of NGQD layers into the structures significantly improves the performance of optoelectronic devices. PMID:27042953

  3. Design strategy for 25% external quantum efficiency in green and blue thermally activated delayed fluorescent devices.

    PubMed

    Lee, Dong Ryun; Kim, Mounggon; Jeon, Sang Kyu; Hwang, Seok-Ho; Lee, Chil Won; Lee, Jun Yeob

    2015-10-21

    Carbazole- and triazine-derived thermally activated delayed fluorescent (TADF) emitters, with three donor units and an even distribution of the highest occupied molecular orbital, achieve high external quantum efficiencies of above 25% in blue and green TADF devices. PMID:26308481

  4. Heralded-qubit amplifiers for practical device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Curty, Marcos; Moroder, Tobias

    2011-07-01

    Device-independent quantum key distribution does not need a precise quantum mechanical model of employed devices to guarantee security. Despite its beauty, it is still a very challenging experimental task. We compare a recent proposal by Gisin [Phys. Rev. Lett.PRLTAO0031-900710.1103/PhysRevLett.105.070501 105, 070501 (2010)] to close the detection loophole problem with that of a simpler quantum relay based on entanglement swapping with linear optics. Our full-mode analysis for both schemes confirms that, in contrast to recent beliefs, the second scheme can indeed provide a positive key rate which is even considerably higher than that of the first alternative. The resulting key rates and required detection efficiencies of approximately 95% for both schemes, however, strongly depend on the underlying security proof.

  5. Near-infrared electroluminescent devices based on colloidal HgTe quantum dot arrays

    NASA Astrophysics Data System (ADS)

    O'Connor, É.; O'Riordan, A.; Doyle, H.; Moynihan, S.; Cuddihy, A.; Redmond, G.

    2005-05-01

    Crystalline 4.6 nm HgTe quantum dots, stabilized by 1-thioglycerol ligands, were synthesized by wet chemical methods. Room-temperature photoluminescence spectra of the dots, both in solution and as solid arrays, exhibited near-infrared emission. Light-emitting devices were fabricated by deposition of quantum dot layers onto glass/indium tin oxide (ITO)/3,4-polyethylene-dioxythiophene-polystyrene sulfonate (PEDOT) substrates followed by top contacting with evaporated aluminum. Room-temperature near-infrared electroluminescence from 1mm2 ITO/PEDOT/HgTe/Al devices, centered at ˜1600nm, with an external quantum efficiency of 0.02% and brightness of 150nW/mm2 at 50 mA and 2.5 V was achieved.

  6. Heralded-qubit amplifiers for practical device-independent quantum key distribution

    SciTech Connect

    Curty, Marcos; Moroder, Tobias

    2011-07-15

    Device-independent quantum key distribution does not need a precise quantum mechanical model of employed devices to guarantee security. Despite its beauty, it is still a very challenging experimental task. We compare a recent proposal by Gisin et al.[Phys. Rev. Lett. 105, 070501 (2010)] to close the detection loophole problem with that of a simpler quantum relay based on entanglement swapping with linear optics. Our full-mode analysis for both schemes confirms that, in contrast to recent beliefs, the second scheme can indeed provide a positive key rate which is even considerably higher than that of the first alternative. The resulting key rates and required detection efficiencies of approximately 95% for both schemes, however, strongly depend on the underlying security proof.

  7. Devices in the management of advanced, chronic heart failure

    PubMed Central

    Abraham, William T.; Smith, Sakima A.

    2013-01-01

    Heart failure (HF) is a global phenomenon, and the overall incidence and prevalence of the condition are steadily increasing. Medical therapies have proven efficacious, but only a small number of pharmacological options are in development. When patients cease to respond adequately to optimal medical therapy, cardiac resynchronization therapy has been shown to improve symptoms, reduce hospitalizations, promote reverse remodelling, and decrease mortality. However, challenges remain in identifying the ideal recipients for this therapy. The field of mechanical circulatory support has seen immense growth since the early 2000s, and left ventricular assist devices (LVADs) have transitioned over the past decade from large, pulsatile devices to smaller, more-compact, continuous-flow devices. Infections and haematological issues are still important areas that need to be addressed. Whereas LVADs were once approved only for ‘bridge to transplantation’, these devices are now used as destination therapy for critically ill patients with HF, allowing these individuals to return to the community. A host of novel strategies, including cardiac contractility modulation, implantable haemodynamic-monitoring devices, and phrenic and vagus nerve stimulation, are under investigation and might have an impact on the future care of patients with chronic HF. PMID:23229137

  8. Simple proof of the quantum benchmark fidelity for continuous-variable quantum devices

    SciTech Connect

    Namiki, Ryo

    2011-04-15

    An experimental success criterion for continuous-variable quantum teleportation and memory is to surpass the limit of the average fidelity achieved by classical measure-and-prepare schemes with respect to a Gaussian-distributed set of coherent states. We present an alternative proof of the classical limit based on the familiar notions of state-channel duality and partial transposition. The present method enables us to produce a quantum-domain criterion associated with a given set of measured fidelities.

  9. Minimum energy surface required by quantum memory devices.

    PubMed

    van Dam, Wim; Nguyen, Hieu D

    2013-06-21

    We address the question of what physical resources are required and sufficient to store classical information. While there is no lower bound on the required energy or space to store information, we find that there is a nonzero lower bound for the product P = of these two resources. Specifically, we prove that any physical system of mass m and d degrees of freedom that stores S bits of information will have a lower bound on the product P that is proportional to d2/m(exp(S/d) - 1)2. This result is obtained in a nonrelativistic, quantum mechanical setting, and it is independent of earlier thermodynamical results such as the Bekenstein bound on the entropy of black holes. PMID:23829720

  10. Detection and measurement of electroreflectance on quantum cascade laser device using Fourier transform infrared microscope

    SciTech Connect

    Enobio, Eli Christopher I.; Ohtani, Keita; Ohno, Yuzo; Ohno, Hideo

    2013-12-02

    We demonstrate the use of a Fourier Transform Infrared microscope system to detect and measure electroreflectance (ER) from mid-infrared quantum cascade laser (QCL) device. To characterize intersubband transition (ISBT) energies in a functioning QCL device, a microscope is used to focus the probe on the QCL cleaved mirror. The measured ER spectra exhibit resonance features associated to ISBTs under applied electric field in agreement with the numerical calculations and comparable to observed photocurrent, and emission peaks. The method demonstrates the potential as a characterization tool for QCL devices.

  11. Trustworthiness of measurement devices in round-robin differential-phase-shift quantum key distribution

    NASA Astrophysics Data System (ADS)

    Cao, Zhu; Yin, Zhen-Qiang; Han, Zheng-Fu

    2016-02-01

    Round-robin differential-phase-shift quantum key distribution (RRDPS QKD) has been proposed to raise the noise tolerability of the channel. However, in practice, the measurement device in RRDPS QKD may be imperfect. Here, we show that, with these imperfections, the security of RRDPS may be damaged by proposing two attacks for RRDPS systems with uncharacterized measurement devices. One is valid even for a system with unit total efficiency, while the other is valid even when a single-photon state is sent. To prevent these attacks, either security arguments need to be fundamentally revised or further practical assumptions on the measurement device should be put.

  12. Broadband calibrated scattering parameters characterization of a superconducting quantum interference device amplifier

    SciTech Connect

    Ranzani, Leonardo; Spietz, Lafe; Aumentado, Jose

    2013-07-08

    In this work, we characterize the 2-port scattering parameters of a superconducting quantum interference device amplifier at {approx}20 mK over several gigahertz of bandwidth. The measurement reference plane is positioned on a 6.25 {Omega} microstrip line situated directly at the input and output of the device by means of a thru-reflect-line cryogenic calibration procedure. From the scattering parameters, we derive the device available power gain, isolation, and input impedance over the 2-8 GHz range. This measurement methodology provides a path towards designing wide-band matching circuits for low impedance superconducting amplifiers operating at dilution refrigerator temperatures.

  13. Using carbon quantum dots to improve the resistive switching behavior of ZnO nanorods device

    NASA Astrophysics Data System (ADS)

    Wang, Xueliang; Xu, Jianping; Shi, Shaobo; Zhang, Xiaosong; Zhang, Xuguang; Shi, Xin; Li, Shubin; Li, Linlin; Liu, Xiaojuan; Li, Lan

    2016-01-01

    An electronic bistable device with a composite structure was fabricated using tapered ZnO nanorod arrays (ZnO NRs) coated with carbon quantum-dots (C QDs). With the addition of C QDs, the ON/OFF resistance ratio is 6 ×102, over 100 times higher than that of device with pristine ZnO NRs. The effect of C QDs on the resistive switching behavior was investigated by current-voltage (I-V) and capacitance-voltage (C-V) characterization. The conduction mechanisms of the devices were discussed using space charge limited current (SCLC) model.

  14. MovAid- a novel device for advanced rehabilitation monitoring.

    PubMed

    Gupta, Prashant; Verma, Piyush; Gupta, Rakesh; Verma, Bhawna

    2015-08-01

    The present article introduces a new device "MovAid" which helps to measure and monitor rehabilitation. It has two main components- "MovAid device" and the "MovAid Smart Phone Application". The device connects wirelessly to the MovAid smart phone application via Bluetooth. It has electronic sensors to measure three important parameters of the patient- Angle of Joint Bent, Lift from the ground and Orientation of the limb. A mono-axis flex sensor to measure the degree of joint bent and a 3-axis accelerometer and gyroscope to measure the orientation of the limb and lift from the ground have been used. MovAid system bridges the gap between caretakers and patients, empowering both in ways never thought of before, by providing detailed and accurate data on every move. PMID:26737332

  15. Advances in dental local anesthesia techniques and devices: An update

    PubMed Central

    Saxena, Payal; Gupta, Saurabh K.; Newaskar, Vilas; Chandra, Anil

    2013-01-01

    Although local anesthesia remains the backbone of pain control in dentistry, researches are going to seek new and better means of managing the pain. Most of the researches are focused on improvement in the area of anesthetic agents, delivery devices and technique involved. Newer technologies have been developed that can assist the dentist in providing enhanced pain relief with reduced injection pain and fewer adverse effects. This overview will enlighten the practicing dentists regarding newer devices and methods of rendering pain control comparing these with the earlier used ones on the basis of research and clinical studies available. PMID:24163548

  16. Template method for nano-order positioning and dense packing of quantum dots for optoelectronic device application

    NASA Astrophysics Data System (ADS)

    Mukai, Kohki; Hirota, Akinobu; Shimizu, Yuta; Nakashima, Seisuke

    2015-04-01

    In this paper, we present recent progress of our researches on positioning of quantum dot in the field of optoelectronics. The first research is aimed at quantum information device application. As a technology for production of quantum devices, we developed the method for positioning of a single colloidal quantum dot. Oxide lines on a Si substrate drawn by a scanning probe microscope were used as a negative etching mask with controlling their cross section in order to create a nanohole for trapping of a single quantum dot. The other research is aimed at solar cell application. It has been predicted that quantum-dot superlattice solar cell will achieve photoelectric conversion efficiency of more than 70%. After the sedimentation of the colloidal quantum dots into the pyramidal holes processed by anisotropic wet etching on a Si substrate, we observed characteristic photoluminescence from the quantum-dot sheet.

  17. Gain dynamics of quantum dot devices for dual-state operation

    SciTech Connect

    Kaptan, Y. Herzog, B.; Kolarczik, M.; Owschimikow, N.; Woggon, U.; Schmeckebier, H.; Arsenijević, D.; Bimberg, D.; Mikhelashvili, V.; Eisenstein, G.

    2014-06-30

    Ground state gain dynamics of In(Ga)As-quantum dot excited state lasers are investigated via single-color ultrafast pump-probe spectroscopy below and above lasing threshold. Two-color pump-probe experiments are used to localize lasing and non-lasing quantum dots within the inhomogeneously broadened ground state. Single-color results yield similar gain recovery rates of the ground state for lasing and non-lasing quantum dots decreasing from 6 ps to 2 ps with increasing injection current. We find that ground state gain dynamics are influenced solely by the injection current and unaffected by laser operation of the excited state. This independence is promising for dual-state operation schemes in quantum dot based optoelectronic devices.

  18. Nanostructured Quantum Dots or Dashes in Photovoltaic Devices and Methods Thereof

    NASA Technical Reports Server (NTRS)

    Raffaele, Ryne P. (Inventor); Wilt, David M. (Inventor)

    2015-01-01

    A photovoltaic device includes one or more structures, an array of at least one of quantum dots and quantum dashes, at least one groove, and at least one conductor. Each of the structures comprises an intrinsic layer on one of an n type layer and a p type layer and the other one of the n type layer and the p type layer on the intrinsic layer. The array of at least one of quantum dots and quantum dashes is located in the intrinsic layer in at least one of the structures. The groove extends into at least one of the structures and the conductor is located along at least a portion of the groove.

  19. Thermodynamic limits to the efficiency of solar energy conversion by quantum devices

    NASA Technical Reports Server (NTRS)

    Buoncristiani, A. M.; Byvik, C. E.; Smith, B. T.

    1981-01-01

    The second law of thermodynamics imposes a strict limitation to the energy converted from direct solar radiation to useful work by a quantum device. This limitation requires that the amount of energy converted to useful work (energy in any form other than heat) can be no greater than the change in free energy of the radiation fields. Futhermore, in any real energy conversion device, not all of this available free energy in the radiation field can be converted to work because of basic limitations inherent in the device itself. A thermodynamic analysis of solar energy conversion by a completely general prototypical quantum device is presented. This device is completely described by two parameters, its operating temperature T sub R and the energy threshold of its absorption spectrum. An expression for the maximum thermodynamic efficiency of a quantum solar converter was derived in terms of these two parameters and the incident radiation spectrum. Efficiency curves for assumed solar spectral irradiance corresponding to air mass zero and air mass 1.5 are presented.

  20. Investigation of thioglycerol stabilized ZnS quantum dots in electroluminescent device performance

    NASA Astrophysics Data System (ADS)

    Ethiraj, Anita Sagadevan; Rhen, Dani; Lee, D. H.; Kang, Dae Joon; Kulkarni, S. K.

    2016-05-01

    The present work is focused on the investigation of thioglycerol (TG) stabilized Zinc Sulfide Quantum dots (ZnS QDs) in the hybrid electroluminescence (EL) device. Optical absorption spectroscopy clearly indicates the formation of narrow size distributed ZnS in the quantum confinement regime. X-ray Diffraction (XRD), Photoluminescence (PL), Energy Dispersive X-ray Spectroscopy (EDS) data supports the same. The hybrid EL device with structure of ITO (indium tin oxide)//PEDOT:PSS ((poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate)//HTL (α NPD- N,N'-diphenyl-N,N'-bis(1-naphthyl)-(1,1'-phenyl)-4,4'-diamine// PVK:ZnS QDs//ETL(PBD- 2-tert-butylphenyl- 5-biphenyl-1,3,4-oxadiazole)//LiF:Al (Device 1) was fabricated. Reference device without the ZnS QDs were also prepared (Device 2). The results show that the ZnS QDs based device exhibited bright electroluminescence emission of 24 cd/m2 at a driving voltage of 16 Volts under the forward bias conditions as compared to the reference device without the ZnS QDs, which showed 6 cd/m2 at ˜22 Volts.

  1. Novel device-based interventional strategies for advanced heart failure.

    PubMed

    Toth, Gabor G; Vanderheyden, Marc; Bartunek, Jozef

    2016-01-01

    While heart failure is one of the leading causes of mortality and morbidity, our tools to provide ultimate treatment solutions are still limited. Recent developments in new devices are designed to fill this therapeutic gap. The scope of this review is to focus on two particular targets, namely (1) left ventricular geometric restoration and (2) atrial depressurization. (1) Reduction of the wall stress by shrinking the ventricular cavity has been traditionally attempted surgically. Recently, the Parachute device (CardioKinetix Inc., Menlo Park, CA, USA) has been introduced to restore ventricular geometry and cardiac mechanics. The intervention aims to partition distal dysfunctional segments that are non-contributory to the ventricular mechanics and forward cardiac output. (2) Diastolic heart failure is characterized by abnormal relaxation and chamber stiffness. The main therapeutic goal achieved should be the reduction of afterload and diastolic pressure load. Recently, new catheter-based approaches were proposed to reduce left atrial pressure and ventricular decompression: the InterAtrial Shunt Device (IASD™) (Corvia Medical Inc., Tewksbury, MA, USA) and the V-Wave Shunt (V-Wave Ltd, Or Akiva, Israel). Both are designed to create a controlled atrial septal defect in symptomatic patients with heart failure. While the assist devices are aimed at end-stage heart failure, emerging device-based percutaneous or minimal invasive techniques comprise a wide spectrum of innovative concepts that target ventricular remodeling, cardiac contractility or neuro-humoral modulation. The clinical adoption is in the early stages of the initial feasibility and safety studies, and clinical evidence needs to be gathered in appropriately designed clinical trials. PMID:26966444

  2. Novel device-based interventional strategies for advanced heart failure

    PubMed Central

    Vanderheyden, Marc; Bartunek, Jozef

    2016-01-01

    While heart failure is one of the leading causes of mortality and morbidity, our tools to provide ultimate treatment solutions are still limited. Recent developments in new devices are designed to fill this therapeutic gap. The scope of this review is to focus on two particular targets, namely (1) left ventricular geometric restoration and (2) atrial depressurization. (1) Reduction of the wall stress by shrinking the ventricular cavity has been traditionally attempted surgically. Recently, the Parachute device (CardioKinetix Inc., Menlo Park, CA, USA) has been introduced to restore ventricular geometry and cardiac mechanics. The intervention aims to partition distal dysfunctional segments that are non-contributory to the ventricular mechanics and forward cardiac output. (2) Diastolic heart failure is characterized by abnormal relaxation and chamber stiffness. The main therapeutic goal achieved should be the reduction of afterload and diastolic pressure load. Recently, new catheter-based approaches were proposed to reduce left atrial pressure and ventricular decompression: the InterAtrial Shunt Device (IASD™) (Corvia Medical Inc., Tewksbury, MA, USA) and the V-Wave Shunt (V-Wave Ltd, Or Akiva, Israel). Both are designed to create a controlled atrial septal defect in symptomatic patients with heart failure. While the assist devices are aimed at end-stage heart failure, emerging device-based percutaneous or minimal invasive techniques comprise a wide spectrum of innovative concepts that target ventricular remodeling, cardiac contractility or neuro-humoral modulation. The clinical adoption is in the early stages of the initial feasibility and safety studies, and clinical evidence needs to be gathered in appropriately designed clinical trials. PMID:26966444

  3. A Comprehensive Microfluidics Device Construction and Characterization Module for the Advanced Undergraduate Analytical Chemistry Laboratory

    ERIC Educational Resources Information Center

    Piunno, Paul A. E.; Zetina, Adrian; Chu, Norman; Tavares, Anthony J.; Noor, M. Omair; Petryayeva, Eleonora; Uddayasankar, Uvaraj; Veglio, Andrew

    2014-01-01

    An advanced analytical chemistry undergraduate laboratory module on microfluidics that spans 4 weeks (4 h per week) is presented. The laboratory module focuses on comprehensive experiential learning of microfluidic device fabrication and the core characteristics of microfluidic devices as they pertain to fluid flow and the manipulation of samples.…

  4. BORON NITRIDE CAPACITORS FOR ADVANCED POWER ELECTRONIC DEVICES

    SciTech Connect

    N. Badi; D. Starikov; C. Boney; A. Bensaoula; D. Johnstone

    2010-11-01

    This project fabricates long-life boron nitride/boron oxynitride thin film -based capacitors for advanced SiC power electronics with a broad operating temperature range using a physical vapor deposition (PVD) technique. The use of vapor deposition provides for precise control and quality material formation.

  5. Advanced investigation of two-phase charge-coupled devices

    NASA Technical Reports Server (NTRS)

    Kosonocky, W. F.; Carnes, J. E.

    1973-01-01

    The performance of experimental two phase, charge-coupled shift registers constructed using polysilicon gates overlapped by aluminum gates was studied. Shift registers with 64, 128, and 500 stages were built and operated. Devices were operated at the maximum clock frequency of 20 MHz. Loss per transfer of less than .0001 was demonstrated for fat zero operation. The effect upon transfer efficiency of various structural and materials parameters was investigated including substrate orientation, resistivity, and conductivity type; channel width and channel length; and method of channel confinement. Operation of the devices with and without fat zero was studied as well as operation in the complete charge transfer mode and the bias charge, or bucket brigade mode.

  6. Finite-key analysis for measurement-device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Song, Ting-Ting; Wen, Qiao-Yan; Guo, Fen-Zhuo; Tan, Xiao-Qing

    2012-08-01

    The length of signal pulses is finite in practical quantum key distribution. The finite-key analysis of an unconditional quantum key distribution is a burning problem, and the efficient quantum key distribution protocol suitable for practical implementation, measurement-device-independent quantum key distribution (MDI QKD), was proposed very recently. We give the finite-key analysis of MDI QKD, which removes all detector side channels and generates many orders of key rate higher than that of full-device-independent quantum key distribution. The secure bound of the ultimate key rate is obtained under the statistical fluctuations of relative frequency, which can be applied directly to practical threshold detectors with low detection efficiency and highly lossy channels. The bound is evaluated for reasonable values of the observed parameters. The simulation shows that the secure distance is around 10 km when the number of sifted data is 1010. Moreover the secure distance would be much longer in practice because of some simplified treatments used in our paper.

  7. Ångström-level, real-time control of the formation of quantum devices

    NASA Astrophysics Data System (ADS)

    Carlsson, S.-B.; Deppert, K.; Junno, T.; Magnusson, M. H.; Montelius, L.; Samuelson, L.

    1998-08-01

    We report a novel approach for the realization of quantum devices which require device structures of sub-10 nm dimensions and position control better than 1 nm. In this approach we combine three methods from nano-technology: (i) an aerosol technique for the fabrication of metallic and semiconducting nano-crystals or nano-particles with diameters in the range 5-50 nm, (ii) extreme electron beam lithography to define contact gap geometries with dimensions of 10-50 nm and (iii) a manipulation technique based on atomic-force microscopy, combined with in situ electrical measurements of the device characteristics, by which pre-fabricated nano-structures can be positioned with high accuracy. We present details of room-temperature measurements on quantized conductance devices, formed in the neck structures between neighbouring gold particles. These necks or wires have a cross-section of only one or a few gold atoms, leading to quantized conductance of 0268-1242/13/8A/035/img1, with values of n between 1 and 10 having been observed. Such lateral quantum resistor devices are found to be remarkably stable, frequently maintaining the conductance levels on the time scale of hours. We also discuss the prospect for novel devices in which a single nano-particle or a single molecule is controllably positioned with high accuracy, with tunnel gaps surrounding the island.

  8. Proximity effect bilayer nano superconducting quantum interference devices for millikelvin magnetometry

    SciTech Connect

    Blois, A. Rozhko, S.; Romans, E. J.; Hao, L.; Gallop, J. C.

    2013-12-21

    Superconducting quantum interference devices (SQUIDs) incorporating thin film nanobridges as weak links have sensitivities approaching that required for single spin detection at 4.2 K. However, due to thermal hysteresis they are difficult to operate at much lower temperatures which hinder their application to many quantum measurements. To overcome this, we have developed nanoscale SQUIDs made from titanium-gold proximity bilayers. We show that their electrical properties are consistent with a theoretical model developed for heat flow in bilayers and demonstrate that they enable magnetic measurements to be made on a sample at system temperatures down to 60 mK.

  9. Multiple functional UV devices based on III-Nitride quantum wells for biological warfare agent detection

    NASA Astrophysics Data System (ADS)

    Wang, Qin; Savage, Susan; Persson, Sirpa; Noharet, Bertrand; Junique, Stéphane; Andersson, Jan Y.; Liuolia, Vytautas; Marcinkevicius, Saulius

    2009-02-01

    We have demonstrated surface normal detecting/filtering/emitting multiple functional ultraviolet (UV) optoelectronic devices based on InGaN/GaN, InGaN/AlGaN and AlxGa1-xN/AlyGa1-yN multiple quantum well (MQW) structures with operation wavelengths ranging from 270 nm to 450 nm. Utilizing MQW structure as device active layer offers a flexibility to tune its long cut-off wavelength in a wide UV range from solar-blind to visible by adjusting the well width, well composition and barrier height. Similarly, its short cut-off wavelength can be adjusted by using a GaN or AlGaN block layer on a sapphire substrate when the device is illuminated from its backside, which further provides an optical filtering effect. When a current injects into the device under forward bias the device acts as an UV light emitter, whereas the device performs as a typical photodetector under reverse biases. With applying an alternating external bias the device might be used as electroabsorption modulator due to quantum confined Stark effect. In present work fabricated devices have been characterized by transmission/absorption spectra, photoresponsivity, electroluminescence, and photoluminescence measurements under various forward and reverse biases. The piezoelectric effect, alloy broadening and Stokes shift between the emission and absorption spectra in different InGaN- and AlGaN-based QW structures have been investigated and compared. Possibilities of monolithic or hybrid integration using such multiple functional devices for biological warfare agents sensing application have also be discussed.

  10. Recent advances in spintronics for emerging memory devices

    NASA Astrophysics Data System (ADS)

    Kang, Seung H.

    2008-09-01

    The emerging field of spintronics has the potential to bring game-changing opportunities to nanoelectronic technologies far beyond its traditional contribution to mass storage applications such as hard disk drives. The value proposition is timely since the dominant semiconductor industry is in pursuit of “More-than-Moore” to extend the technology roadmap or to create functional diversifications through enhanced system platforms. This article overviews a promising spintronic device in conjunction with recent breakthroughs in tunnel magnetoresistance and spin-transfer-torque magnetization switching.

  11. N-dimensional measurement-device-independent quantum key distribution with N + 1 un-characterized sources: zero quantum-bit-error-rate case.

    PubMed

    Hwang, Won-Young; Su, Hong-Yi; Bae, Joonwoo

    2016-01-01

    We study N-dimensional measurement-device-independent quantum-key-distribution protocol where one checking state is used. Only assuming that the checking state is a superposition of other N sources, we show that the protocol is secure in zero quantum-bit-error-rate case, suggesting possibility of the protocol. The method may be applied in other quantum information processing. PMID:27452275

  12. N-dimensional measurement-device-independent quantum key distribution with N + 1 un-characterized sources: zero quantum-bit-error-rate case

    PubMed Central

    Hwang, Won-Young; Su, Hong-Yi; Bae, Joonwoo

    2016-01-01

    We study N-dimensional measurement-device-independent quantum-key-distribution protocol where one checking state is used. Only assuming that the checking state is a superposition of other N sources, we show that the protocol is secure in zero quantum-bit-error-rate case, suggesting possibility of the protocol. The method may be applied in other quantum information processing. PMID:27452275

  13. River Devices to Recover Energy with Advanced Materials (River DREAM)

    SciTech Connect

    McMahon, Daniel P.

    2013-07-03

    The purpose of this project is to develop a generator called a Galloping Hydroelectric Energy Extraction Device (GHEED). It uses a galloping prism to convert water flow into linear motion. This motion is converted into electricity via a dielectric elastomer generator (DEG). The galloping mechanism and the DEG are combined to create a system to effectively generate electricity. This project has three research objectives: 1. Oscillator development and design a. Characterize galloping behavior, evaluate control surface shape change on oscillator performance and demonstrate shape change with water flow change. 2. Dielectric Energy Generator (DEG) characterization and modeling a. Characterize and model the performance of the DEG based on oscillator design 3. Galloping Hydroelectric Energy Extraction Device (GHEED) system modeling and integration a. Create numerical models for construction of a system performance model and define operating capabilities for this approach Accomplishing these three objectives will result in the creation of a model that can be used to fully define the operating parameters and performance capabilities of a generator based on the GHEED design. This information will be used in the next phase of product development, the creation of an integrated laboratory scale generator to confirm model predictions.

  14. Advanced Thermophotovoltaic Devices for Space Nuclear Power Systems

    SciTech Connect

    Wernsman, Bernard; Mahorter, Robert G.; Siergiej, Richard; Link, Samuel D.; Wehrer, Rebecca J.; Belanger, Sean J.; Fourspring, Patrick; Murray, Susan; Newman, Fred; Taylor, Dan; Rahmlow, Tom

    2005-02-06

    Advanced thermophotovoltaic (TPV) modules capable of producing > 0.3 W/cm2 at an efficiency > 22% while operating at a converter radiator and module temperature of 1228 K and 325 K, respectively, have been made. These advanced TPV modules are projected to produce > 0.9 W/cm2 at an efficiency > 24% while operating at a converter radiator and module temperature of 1373 K and 325 K, respectively. Radioisotope and nuclear (fission) powered space systems utilizing these advanced TPV modules have been evaluated. For a 100 We radioisotope TPV system, systems utilizing as low as 2 general purpose heat source (GPHS) units are feasible, where the specific power for the 2 and 3 GPHS unit systems operating in a 200 K environment is as large as {approx} 16 We/kg and {approx} 14 We/kg, respectively. For a 100 kWe nuclear powered (as was entertained for the thermoelectric SP-100 program) TPV system, the minimum system radiator area and mass is {approx} 640 m2 and {approx} 1150 kg, respectively, for a converter radiator, system radiator and environment temperature of 1373 K, 435 K and 200 K, respectively. Also, for a converter radiator temperature of 1373 K, the converter volume and mass remains less than 0.36 m3 and 640 kg, respectively. Thus, the minimum system radiator + converter (reactor and shield not included) specific mass is {approx} 16 kg/kWe for a converter radiator, system radiator and environment temperature of 1373 K, 425 K and 200 K, respectively. Under this operating condition, the reactor thermal rating is {approx} 1110 kWt. Due to the large radiator area, the added complexity and mission risk needs to be weighed against reducing the reactor thermal rating to determine the feasibility of using TPV for space nuclear (fission) power systems.

  15. Advanced Thermophotovoltaic Devices for Space Nuclear Power Systems

    NASA Astrophysics Data System (ADS)

    Wernsman, Bernard; Mahorter, Robert G.; Siergiej, Richard; Link, Samuel D.; Wehrer, Rebecca J.; Belanger, Sean J.; Fourspring, Patrick; Murray, Susan; Newman, Fred; Taylor, Dan; Rahmlow, Tom

    2005-02-01

    Advanced thermophotovoltaic (TPV) modules capable of producing > 0.3 W/cm2 at an efficiency > 22% while operating at a converter radiator and module temperature of 1228 K and 325 K, respectively, have been made. These advanced TPV modules are projected to produce > 0.9 W/cm2 at an efficiency > 24% while operating at a converter radiator and module temperature of 1373 K and 325 K, respectively. Radioisotope and nuclear (fission) powered space systems utilizing these advanced TPV modules have been evaluated. For a 100 We radioisotope TPV system, systems utilizing as low as 2 general purpose heat source (GPHS) units are feasible, where the specific power for the 2 and 3 GPHS unit systems operating in a 200 K environment is as large as ˜ 16 We/kg and ˜ 14 We/kg, respectively. For a 100 kWe nuclear powered (as was entertained for the thermoelectric SP-100 program) TPV system, the minimum system radiator area and mass is ˜ 640 m2 and ˜ 1150 kg, respectively, for a converter radiator, system radiator and environment temperature of 1373 K, 435 K and 200 K, respectively. Also, for a converter radiator temperature of 1373 K, the converter volume and mass remains less than 0.36 m3 and 640 kg, respectively. Thus, the minimum system radiator + converter (reactor and shield not included) specific mass is ˜ 16 kg/kWe for a converter radiator, system radiator and environment temperature of 1373 K, 425 K and 200 K, respectively. Under this operating condition, the reactor thermal rating is ˜ 1110 kWt. Due to the large radiator area, the added complexity and mission risk needs to be weighed against reducing the reactor thermal rating to determine the feasibility of using TPV for space nuclear (fission) power systems.

  16. Low-cost SWIR sensors: advancing the performance of ROIC-integrated colloidal quantum dot photodiode arrays

    NASA Astrophysics Data System (ADS)

    Klem, Ethan J. D.; Lewis, Jay; Gregory, Chris; Temple, Dorota; Wijewarnasuriya, Priyalal S.; Dhar, Nibir

    2014-06-01

    RTI has developed a novel photodiode technology based on solution-processed PbS colloidal quantum dots (CQD) capable of providing low-cost, high performance detection across the Vis-SWIR spectral range. The most significant advantages of the CQD technology are ease of fabrication, small pixel size, and extended wavelength range. The devices are fabricated directly onto the ROIC substrate at low temperatures compatible with CMOS, and arrays can be fabricated at wafer scale. We will discuss recent advances in device architecture and processing that result in measured dark currents of 15 nA/cm2 at room temperature and enhanced SWIR responsivity from the UV to ~1.7 μm, compare these results to InGaAs detectors, and present measurements of the CQD detectors temperature dependent dark current.

  17. Advanced Epi Tools for Gallium Nitride Light Emitting Diode Devices

    SciTech Connect

    Patibandla, Nag; Agrawal, Vivek

    2012-12-01

    Over the course of this program, Applied Materials, Inc., with generous support from the United States Department of Energy, developed a world-class three chamber III-Nitride epi cluster tool for low-cost, high volume GaN growth for the solid state lighting industry. One of the major achievements of the program was to design, build, and demonstrate the world’s largest wafer capacity HVPE chamber suitable for repeatable high volume III-Nitride template and device manufacturing. Applied Materials’ experience in developing deposition chambers for the silicon chip industry over many decades resulted in many orders of magnitude reductions in the price of transistors. That experience and understanding was used in developing this GaN epi deposition tool. The multi-chamber approach, which continues to be unique in the ability of the each chamber to deposit a section of the full device structure, unlike other cluster tools, allows for extreme flexibility in the manufacturing process. This robust architecture is suitable for not just the LED industry, but GaN power devices as well, both horizontal and vertical designs. The new HVPE technology developed allows GaN to be grown at a rate unheard of with MOCVD, up to 20x the typical MOCVD rates of 3{micro}m per hour, with bulk crystal quality better than the highest-quality commercial GaN films grown by MOCVD at a much cheaper overall cost. This is a unique development as the HVPE process has been known for decades, but never successfully commercially developed for high volume manufacturing. This research shows the potential of the first commercial-grade HVPE chamber, an elusive goal for III-V researchers and those wanting to capitalize on the promise of HVPE. Additionally, in the course of this program, Applied Materials built two MOCVD chambers, in addition to the HVPE chamber, and a robot that moves wafers between them. The MOCVD chambers demonstrated industry-leading wavelength yield for GaN based LED wafers and industry

  18. Quantum filter of spin polarized states: Metal–dielectric–ferromagnetic/semiconductor device

    SciTech Connect

    Makarov, Vladimir I.; Khmelinskii, Igor

    2014-02-01

    Highlights: • Development of a new spintronics device. • Development of quantum spin polarized filters. • Development of theory of quantum spin polarized filter. - Abstract: Recently we proposed a model for the Quantum Spin-Polarized State Filter (QSPSF). The magnetic moments are transported selectively in this model, detached from the electric charge carriers. Thus, transfer of a spin-polarized state between two conductors was predicted in a system of two levels coupled by exchange interaction. The strength of the exchange interaction between the two conductive layers depends on the thickness of the dielectric layer separating them. External magnetic fields modulate spin-polarized state transfer, due to Zeeman level shift. Therefore, a linearly growing magnetic field generates a series of current peaks in a nearby coil. Thus, our spin-state filter should contain as least three nanolayers: (1) conductive or ferromagnetic; (2) dielectric; and (3) conductive or semiconductive. The spectrum of spin-polarized states generated by the filter device consists of a series of resonance peaks. In a simple case the number of lines equals S, the total spin angular momentum of discrete states in one of the coupled nanolayers. Presently we report spin-polarized state transport in metal–dielectric–ferromagnetic (MDF) and metal–dielectric–semiconductor (MDS) three-layer sandwich devices. The exchange-resonance spectra in such devices are quite specific, differing also from spectra observed earlier in other three-layer devices. The theoretical model is used to interpret the available experimental results. A detailed ab initio analysis of the magnetic-field dependence of the output magnetic moment averaged over the surface of the device was carried out. The model predicts the resonance structure of the signal, although at its present accuracy it cannot predict the positions of the spectral peaks.

  19. Advanced materials development for multi-junction monolithic photovoltaic devices

    SciTech Connect

    Dawson, L.R.; Reno, J.L.

    1996-07-01

    We report results in three areas of research relevant to the fabrication of monolithic multi-junction photovoltaic devices. (1) The use of compliant intervening layers grown between highly mismatched materials, GaAs and GaP (same lattice constant as Si), is shown to increase the structural quality of the GaAs overgrowth. (2) The use of digital alloys applied to the MBE growth of GaAs{sub x}Sb{sub l-x} (a candidate material for a two junction solar cell) provides increased control of the alloy composition without degrading the optical properties. (3) A nitrogen plasma discharge is shown to be an excellent p-type doping source for CdTe and ZnTe, both of which are candidate materials for a two junction solar cell.

  20. Note: Increasing dynamic range of digital-to-analog converter using a superconducting quantum interference device

    SciTech Connect

    Nakanishi, Masakazu

    2014-10-15

    Responses of a superconducting quantum interference device (SQUID) are periodically dependent on magnetic flux coupling to its superconducting ring and the period is a flux quantum (Φ{sub o} = h/2e, where h and e, respectively, express Planck's constant and elementary charge). Using this periodicity, we had proposed a digital to analog converter using a SQUID (SQUID DAC) of first generation with linear current output, interval of which corresponded to Φ{sub o}. Modification for increasing dynamic range by interpolating within each interval is reported. Linearity of the interpolation was also based on the quantum periodicity. A SQUID DAC with dynamic range of about 1.4 × 10{sup 7} was created as a demonstration.

  1. Quantum bounds on multiplayer linear games and device-independent witness of genuine tripartite entanglement

    NASA Astrophysics Data System (ADS)

    Murta, Gláucia; Ramanathan, Ravishankar; Móller, Natália; Terra Cunha, Marcelo

    2016-02-01

    Here we study multiplayer linear games, a natural generalization of xor games to multiple outcomes. We generalize a recently proposed efficiently computable bound, in terms of the norm of a game matrix, on the quantum value of two-player games to linear games with n players. As an example, we bound the quantum value of a generalization of the well-known CHSH game to n players and d outcomes. We also apply the bound to show in a simple manner that any nontrivial functional box, that could lead to trivialization of communication complexity in a multiparty scenario, cannot be realized in quantum mechanics. We then present a systematic method to derive device-independent witnesses of genuine tripartite entanglement.

  2. Hybrid Quantum Point Contact-Superconductor Devices Using InSb Nanowires

    NASA Astrophysics Data System (ADS)

    Gill, Stephen; Damasco, John Jeffrey; Car, Diana; Bakkers, Erik; Mason, Nadya

    Recent experiments using hybrid nanowire (NW)-superconductor (SC) devices have provided evidence for Majorana quasiparticles in tunneling experiments. However, these tunneling experiments are marked by a soft superconducting gap, which likely originates from disorder at the NW-SC interface. Hence, clean NW-SC interfaces are important for future Majorana studies. By carefully processing the NW-SC interface, we have realized quantized conductance steps in quantum point contacts fabricated from InSb NWs and superconducting contacts. We study the length dependence of ballistic behavior and the induced superconductivity in InSb NWs by quantum point contact spectroscopy. Additionally, we discuss how the transport in InSb NW-SC quantum point contacts evolves in magnetic field.

  3. Long-distance measurement-device-independent quantum key distribution with coherent-state superpositions.

    PubMed

    Yin, H-L; Cao, W-F; Fu, Y; Tang, Y-L; Liu, Y; Chen, T-Y; Chen, Z-B

    2014-09-15

    Measurement-device-independent quantum key distribution (MDI-QKD) with decoy-state method is believed to be securely applied to defeat various hacking attacks in practical quantum key distribution systems. Recently, the coherent-state superpositions (CSS) have emerged as an alternative to single-photon qubits for quantum information processing and metrology. Here, in this Letter, CSS are exploited as the source in MDI-QKD. We present an analytical method that gives two tight formulas to estimate the lower bound of yield and the upper bound of bit error rate. We exploit the standard statistical analysis and Chernoff bound to perform the parameter estimation. Chernoff bound can provide good bounds in the long-distance MDI-QKD. Our results show that with CSS, both the security transmission distance and secure key rate are significantly improved compared with those of the weak coherent states in the finite-data case. PMID:26466295

  4. Measurement device-independent quantum key distribution with heralded pair coherent state

    NASA Astrophysics Data System (ADS)

    Chen, Dong; Shang-Hong, Zhao; Lei, Shi

    2016-07-01

    The original measurement device-independent quantum key distribution is reviewed, and a modified protocol using heralded pair coherent state (HPCS) is proposed to overcome the quantum bit error rate associated with the dark count rate of the detectors in long-distance quantum key distribution. Our simulation indicates that the secure transmission distance can be improved evidently with HPCS owing to the lower probability of vacuum events when compared with weak coherent source scenario, while the secure key rate can be increased with HPCS due to the higher probability of single-photon events when compared with heralded single-photon source scenario. Furthermore, we apply the finite key analysis to the decoy state MDI-QKD with HPCS and obtain a practical key rate.

  5. Measurement-Device-Independent Quantum Key Distribution over Untrustful Metropolitan Network

    NASA Astrophysics Data System (ADS)

    Tang, Yan-Lin; Yin, Hua-Lei; Zhao, Qi; Liu, Hui; Sun, Xiang-Xiang; Huang, Ming-Qi; Zhang, Wei-Jun; Chen, Si-Jing; Zhang, Lu; You, Li-Xing; Wang, Zhen; Liu, Yang; Lu, Chao-Yang; Jiang, Xiao; Ma, Xiongfeng; Zhang, Qiang; Chen, Teng-Yun; Pan, Jian-Wei

    2016-01-01

    Quantum cryptography holds the promise to establish an information-theoretically secure global network. All field tests of metropolitan-scale quantum networks to date are based on trusted relays. The security critically relies on the accountability of the trusted relays, which will break down if the relay is dishonest or compromised. Here, we construct a measurement-device-independent quantum key distribution (MDIQKD) network in a star topology over a 200-square-kilometer metropolitan area, which is secure against untrustful relays and against all detection attacks. In the field test, our system continuously runs through one week with a secure key rate 10 times larger than previous results. Our results demonstrate that the MDIQKD network, combining the best of both worlds—security and practicality, constitutes an appealing solution to secure metropolitan communications.

  6. Electroluminescence of carbon ‘quantum' dots - From materials to devices

    NASA Astrophysics Data System (ADS)

    Veca, L. Monica; Diac, Andreea; Mihalache, Iuliana; Wang, Ping; LeCroy, Gregory E.; Pavelescu, Emil Mihai; Gavrila, Raluca; Vasile, Eugeniu; Terec, Anamaria; Sun, Ya-Ping

    2014-10-01

    Carbon ‘quantum' dots or carbon dots have emerged as a new class of luminescent nanomaterials. While photoluminescence properties of carbon dots had targeted optical imaging and related usage, their unique excited state redox processes responsible for the luminescence emissions may find potentially significant optoelectronic applications. In this regard, we investigated the electroluminescence properties of the carbon dots integrated into multilayer light emitting diode devices. The devices emitted white light with a slight blue color, visible to naked eyes, thus validating the expectation that carbon dots may potentially serve as a new platform for electroluminescent nanomaterials.

  7. Efficient heralding of photonic qubits with applications to device-independent quantum key distribution

    SciTech Connect

    Pitkanen, David; Ma Xiongfeng; Luetkenhaus, Norbert; Wickert, Ricardo; Loock, Peter van

    2011-08-15

    We present an efficient way of heralding photonic qubit signals using linear optics devices. First, we show that one can obtain asymptotically perfect heralding and unit success probability with growing resources. Second, we show that even using finite resources, we can improve qualitatively and quantitatively over earlier heralding results. In the latter scenario, we can obtain perfect heralded photonic qubits while maintaining a finite success probability. We demonstrate the advantage of our heralding scheme by predicting key rates for device-independent quantum key distribution, taking imperfections of sources and detectors into account.

  8. Secondary treatment of films of colloidal quantum dots for optoelectronics and devices produced thereby

    DOEpatents

    Semonin, Octavi Escala; Luther, Joseph M; Beard, Matthew C; Chen, Hsiang-Yu

    2014-04-01

    A method of forming an optoelectronic device. The method includes providing a deposition surface and contacting the deposition surface with a ligand exchange chemical and contacting the deposition surface with a quantum dot (QD) colloid. This initial process is repeated over one or more cycles to form an initial QD film on the deposition surface. The method further includes subsequently contacting the QD film with a secondary treatment chemical and optionally contacting the surface with additional QDs to form an enhanced QD layer exhibiting multiple exciton generation (MEG) upon absorption of high energy photons by the QD active layer. Devices having an enhanced QD active layer as described above are also disclosed.

  9. Getting something out of nothing in the measurement-device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Tan, Yong-Gang; Cai, Qing-Yu; Yang, Hai-Feng; Hu, Yao-Hua

    2015-11-01

    Because of the monogamy of entanglement, the measurement-device-independent quantum key distribution is immune to the side-information leaking of the measurement devices. When the correlated measurement outcomes are generated from the dark counts, no entanglement is actually obtained. However, secure key bits can still be proven to be generated from these measurement outcomes. Especially, we will give numerical studies on the contributions of dark counts to the key generation rate in practical decoy state MDI-QKD where a signal source, a weaker decoy source and a vacuum decoy source are used by either legitimate key distributer.

  10. Combining semiconductor quantum dots and bioscaffolds into nanoscale energy transfer devices.

    PubMed

    Spillmann, Christopher M; Stewart, Michael H; Susumu, Kimihiro; Medintz, Igor L

    2015-11-01

    Significant advances have been made in the development of nanoscale devices capable of exciton transport via Förster resonance energy transfer. Several requirements must be met for effective operation, including a reliable energy-harvesting source along with highly organized, precisely placed energy relay elements. For the latter, biological scaffolds such as DNA provide a customizable, symmetric, and stable structure that can be site-specifically modified with organic fluorophores. Here, advancements in nanoscale energy transfer devices incorporating semiconductor nanocrystals and bioscaffolds are reviewed with discussion of biofunctionalization, linker chemistries, design considerations, and concluding with applications in light harvesting, multiplexed biosensing, and optical logic. PMID:26560627

  11. Tradeoff between energy and error in the discrimination of quantum-optical devices

    SciTech Connect

    Bisio, Alessandro; Dall'Arno, Michele; D'Ariano, Giacomo Mauro

    2011-07-15

    We address the problem of energy-error tradeoff in the discrimination between two linear passive quantum optical devices with a single use. We provide an analytical derivation of the optimal strategy for beamsplitters and an iterative algorithm converging to the optimum in the general case. We then compare the optimal strategy with a simpler strategy using coherent input states and homodyne detection. It turns out that the former requires much less energy in order to achieve the same performances.

  12. Note: A hand-held high-Tc superconducting quantum interference device operating without shielding.

    PubMed

    He, D F

    2011-02-01

    By improving the compensation circuit, a hand-held high-Tc rf superconducting quantum interference devices (SQUID) system was developed. It could operate well when moving in unshielded environment. To check the operation, it was used to do eddy-current testing by hand moving the SQUID, and the artificial defect under 6 mm aluminum plate could be successfully detected in shielded environment. PMID:21361649

  13. Retrieval of original signals for superconducting quantum interference device operating in flux locked mode

    NASA Astrophysics Data System (ADS)

    Liu, Dang-Ting; Tian, Ye; Zhao, Shi-Ping; Ren, Yu-Feng; Chen, Geng-Hua

    2015-04-01

    We discuss a simple relation between the input and output signals of a superconducting quantum interference device magnetometer operating in flux locked mode in a cosine curve approximation. According to this relation, an original fast input signal can be easily retrieved from its distorted output response. This technique can be used in some areas such as sensitive and fast detection of magnetic or metallic grains in medicine and food security checking.

  14. 9 CFR 381.131 - Preparation of labeling or other devices bearing official inspection marks without advance...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... devices bearing official inspection marks without advance approval prohibited; exceptions. 381.131 Section... Preparation of labeling or other devices bearing official inspection marks without advance approval prohibited... otherwise make any marking device containing any official mark or simulation thereof, or any label...

  15. Carrier multiplication detected through transient photocurrent in device-grade films of lead selenide quantum dots

    DOE PAGESBeta

    Gao, Jianbo; Fidler, Andrew F.; Klimov, Victor I.

    2015-09-08

    In carrier multiplication, the absorption of a single photon results in two or more electron–hole pairs. Quantum dots are promising materials for implementing carrier multiplication principles in real-life technologies. So far, however, most of research in this area has focused on optical studies of solution samples with yet to be proven relevance to practical devices. We report ultra-fast electro-optical studies of device-grade films of electronically coupled quantum dots that allow us to observe multiplication directly in the photocurrent. Our studies help rationalize previous results from both optical spectroscopy and steady-state photocurrent measurements and also provide new insights into effects ofmore » electric field and ligand treatments on multiexciton yields. Importantly, we demonstrate that using appropriate chemical treatments of the films, extra charges produced by carrier multiplication can be extracted from the quantum dots before they are lost to Auger recombination and hence can contribute to photocurrent of practical devices.« less

  16. Advanced Simulation Technology to Design Etching Process on CMOS Devices

    NASA Astrophysics Data System (ADS)

    Kuboi, Nobuyuki

    2015-09-01

    Prediction and control of plasma-induced damage is needed to mass-produce high performance CMOS devices. In particular, side-wall (SW) etching with low damage is a key process for the next generation of MOSFETs and FinFETs. To predict and control the damage, we have developed a SiN etching simulation technique for CHxFy/Ar/O2 plasma processes using a three-dimensional (3D) voxel model. This model includes new concepts for the gas transportation in the pattern, detailed surface reactions on the SiN reactive layer divided into several thin slabs and C-F polymer layer dependent on the H/N ratio, and use of ``smart voxels''. We successfully predicted the etching properties such as the etch rate, polymer layer thickness, and selectivity for Si, SiO2, and SiN films along with process variations and demonstrated the 3D damage distribution time-dependently during SW etching on MOSFETs and FinFETs. We confirmed that a large amount of Si damage was caused in the source/drain region with the passage of time in spite of the existing SiO2 layer of 15 nm in the over etch step and the Si fin having been directly damaged by a large amount of high energy H during the removal step of the parasitic fin spacer leading to Si fin damage to a depth of 14 to 18 nm. By analyzing the results of these simulations and our previous simulations, we found that it is important to carefully control the dose of high energy H, incident energy of H, polymer layer thickness, and over-etch time considering the effects of the pattern structure, chamber-wall condition, and wafer open area ratio. In collaboration with Masanaga Fukasawa and Tetsuya Tatsumi, Sony Corporation. We thank Mr. T. Shigetoshi and Mr. T. Kinoshita of Sony Corporation for their assistance with the experiments.

  17. Advances in quantum cascade lasers for security and crime-fighting

    NASA Astrophysics Data System (ADS)

    Normand, Erwan L.; Stokes, Robert J.; Hay, Kenneth; Foulger, Brian; Lewis, Colin

    2010-10-01

    Advances in the application of Quantum Cascade Lasers (QCL) to trace gas detection will be presented. The solution is real time (~1 μsec per scan), is insensitive to turbulence and vibration, and performs multiple measurements in one sweep. The QCL provides a large dynamic range, which is a linear response from ppt to % level. The concentration can be derived with excellent immunity from cross interference. Point sensing sensors developed by Cascade for home made and commercial explosives operate by monitoring key constituents in real time and matching this to a spatial event (i.e. sniffer device placed close to an object or person walking through portal (overt or covert). Programmable signature detection capability allows for detection of multiple chemical compounds along the most likely array of explosive chemical formulation. The advantages of configuration as "point sensing" or "stand off" will be discussed. In addition to explosives this method is highly applicable to the detection of mobile drugs labs through volatile chemical release.

  18. Advanced Level Physics Students' Conceptions of Quantum Physics.

    ERIC Educational Resources Information Center

    Mashhadi, Azam

    This study addresses questions about particle physics that focus on the nature of electrons. Speculations as to whether they are more like particles or waves or like neither illustrate the difficulties with which students are confronted when trying to incorporate the concepts of quantum physics into their overall conceptual framework. Such…

  19. Current state-of-the-art of device therapy for advanced heart failure

    PubMed Central

    Lee, Lawrence S.; Shekar, Prem S.

    2014-01-01

    Heart failure remains one of the most common causes of morbidity and mortality worldwide. The advent of mechanical circulatory support devices has allowed significant improvements in patient survival and quality of life for those with advanced or end-stage heart failure. We provide a general overview of past and current mechanical circulatory support devices encompassing options for both short- and long-term ventricular support. PMID:25559828

  20. Verification, Validation and Credibility Assessment of a Computational Model of the Advanced Resistive Exercise Device (ARED)

    NASA Technical Reports Server (NTRS)

    Werner, C. R.; Humphreys, B. T.; Mulugeta, L.

    2014-01-01

    The Advanced Resistive Exercise Device (ARED) is the resistive exercise device used by astronauts on the International Space Station (ISS) to mitigate bone loss and muscle atrophy due to extended exposure to microgravity (micro g). The Digital Astronaut Project (DAP) has developed a multi-body dynamics model of biomechanics models for use in spaceflight exercise physiology research and operations. In an effort to advance model maturity and credibility of the ARED model, the DAP performed verification, validation and credibility (VV and C) assessment of the analyses of the model in accordance to NASA-STD-7009 'Standards for Models and Simulations'.

  1. The enhanced measurement-device-independent quantum key distribution with two-intensity decoy states

    NASA Astrophysics Data System (ADS)

    Zhu, Jian-Rong; Zhu, Feng; Zhou, Xing-Yu; Wang, Qin

    2016-06-01

    We put forward a new scheme for implementing the measurement-device-independent quantum key distribution (QKD) with weak coherent source, while using only two different intensities. In the new scheme, we insert a beam splitter and a local detector at both Alice's and Bob's side, and then all the triggering and non-triggering signals could be employed to process parameter estimations, resulting in very precise estimations for the two-single-photon contributions. Besides, we compare its behavior with two other often used methods, i.e., the conventional standard three-intensity decoy-state measurement-device-independent QKD and the passive measurement-device-independent QKD. Through numerical simulations, we demonstrate that our new approach can exhibit outstanding characteristics not only in the secure transmission distance, but also in the final key generation rate.

  2. Advanced upper limb prosthetic devices: implications for upper limb prosthetic rehabilitation.

    PubMed

    Resnik, Linda; Meucci, Marissa R; Lieberman-Klinger, Shana; Fantini, Christopher; Kelty, Debra L; Disla, Roxanne; Sasson, Nicole

    2012-04-01

    The number of catastrophic injuries caused by improvised explosive devices in the Afghanistan and Iraq Wars has increased public, legislative, and research attention to upper limb amputation. The Department of Veterans Affairs (VA) has partnered with the Defense Advanced Research Projects Agency and DEKA Integrated Solutions to optimize the function of an advanced prosthetic arm system that will enable greater independence and function. In this special communication, we examine current practices in prosthetic rehabilitation including trends in adoption and use of prosthetic devices, financial considerations, and the role of rehabilitation team members in light of our experiences with a prototype advanced upper limb prosthesis during a VA study to optimize the device. We discuss key challenges in the adoption of advanced prosthetic technology and make recommendations for service provision and use of advanced upper limb prosthetics. Rates of prosthetic rejection are high among upper limb amputees. However, these rates may be reduced with sufficient training by a highly specialized, multidisciplinary team of clinicians, and a focus on patient education and empowerment throughout the rehabilitation process. There are significant challenges emerging that are unique to implementing the use of advanced upper limb prosthetic technology, and a lack of evidence to establish clinical guidelines regarding prosthetic prescription and treatment. Finally, we make recommendations for future research to aid in the identification of best practices and development of policy decisions regarding insurance coverage of prosthetic rehabilitation. PMID:22464092

  3. Evaluation of advanced cooling therapy's esophageal cooling device for core temperature control.

    PubMed

    Naiman, Melissa; Shanley, Patrick; Garrett, Frank; Kulstad, Erik

    2016-05-01

    Managing core temperature is critical to patient outcomes in a wide range of clinical scenarios. Previous devices designed to perform temperature management required a trade-off between invasiveness and temperature modulation efficiency. The Esophageal Cooling Device, made by Advanced Cooling Therapy (Chicago, IL), was developed to optimize warming and cooling efficiency through an easy and low risk procedure that leverages heat transfer through convection and conduction. Clinical data from cardiac arrest, fever, and critical burn patients indicate that the Esophageal Cooling Device performs very well both in terms of temperature modulation (cooling rates of approximately 1.3°C/hour, warming of up to 0.5°C/hour) and maintaining temperature stability (variation around goal temperature ± 0.3°C). Physicians have reported that device performance is comparable to the performance of intravascular temperature management techniques and superior to the performance of surface devices, while avoiding the downsides associated with both. PMID:27043177

  4. Biased decoy-state measurement-device-independent quantum cryptographic conferencing with finite resources.

    PubMed

    Chen, RuiKe; Bao, WanSu; Zhou, Chun; Li, Hongwei; Wang, Yang; Bao, HaiZe

    2016-03-21

    In recent years, a large quantity of work have been done to narrow the gap between theory and practice in quantum key distribution (QKD). However, most of them are focus on two-party protocols. Very recently, Yao Fu et al proposed a measurement-device-independent quantum cryptographic conferencing (MDI-QCC) protocol and proved its security in the limit of infinitely long keys. As a step towards practical application for MDI-QCC, we design a biased decoy-state measurement-device-independent quantum cryptographic conferencing protocol and analyze the performance of the protocol in both the finite-key and infinite-key regime. From numerical simulations, we show that our decoy-state analysis is tighter than Yao Fu et al. That is, we can achieve the nonzero asymptotic secret key rate in long distance with approximate to 200km and we also demonstrate that with a finite size of data (say 1011 to 1013 signals) it is possible to perform secure MDI-QCC over reasonable distances. PMID:27136849

  5. Predicting the valley physics of silicon quantum dots directly from a device layout

    NASA Astrophysics Data System (ADS)

    Gamble, John King; Harvey-Collard, Patrick; Jacobson, N. Tobias; Bacewski, Andrew D.; Nielsen, Erik; Montaño, Inès; Rudolph, Martin; Carroll, Malcolm S.; Muller, Richard P.

    Qubits made from electrostatically-defined quantum dots in Si-based systems are excellent candidates for quantum information processing applications. However, the multi-valley structure of silicon's band structure provides additional challenges for the few-electron physics critical to qubit manipulation. Here, we present a theory for valley physics that is predictive, in that we take as input the real physical device geometry and experimental voltage operation schedule, and with minimal approximation compute the resulting valley physics. We present both effective mass theory and atomistic tight-binding calculations for two distinct metal-oxide-semiconductor (MOS) quantum dot systems, directly comparing them to experimental measurements of the valley splitting. We conclude by assessing these detailed simulations' utility for engineering desired valley physics in future devices. Sandia is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the US Department of Energy's National Nuclear Security Administration under Contract No. DE-AC04-94AL85000. The authors gratefully acknowledge support from the Sandia National Laboratories Truman Fellowship Program, which is funded by the Laboratory Directed Research and Development (LDRD) Program.

  6. Nanoscience and technology: An interdisciplinary initiative, self-assembling nanoscale quantum devices

    SciTech Connect

    Doolen, G.; Smith, D.; Mineev, M.

    1996-10-01

    This is the final report of a three-year Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Our objective is to develop the devices, interconnection technologies, and self-assembling systems required for quantum-based information processing that permit ultra-dense integrated circuits and that allow continuation of the on-going silicon VLSI miniaturization process. That process is facing increasing difficulties related to switch performance, heat dissipation, interconnect failure, quantum effect complications, and rapidly escalating manufacturing costs. Our approach is intended to address these concerns and consists of the development of highly parallel stochastic computers utilizing quantum components and self-assembly methods; the development of self-assembling monolayers for use as resists and memory devices; and research on approaches to molecular self-assembly of the precursors to molecular transistors. The work will provide confirmation of principles, is intended to provide near-term results of potential relevance to the commercial sector, and has a range of applications that include high performance computing, biotechnology, and nanoscale chemistry.

  7. A monogamy-of-entanglement game with applications to device-independent quantum cryptography

    NASA Astrophysics Data System (ADS)

    Tomamichel, Marco; Fehr, Serge; Kaniewski, Jędrzej; Wehner, Stephanie

    2013-10-01

    We consider a game in which two separate laboratories collaborate to prepare a quantum system and are then asked to guess the outcome of a measurement performed by a third party in a random basis on that system. Intuitively, by the uncertainty principle and the monogamy of entanglement, the probability that both players simultaneously succeed in guessing the outcome correctly is bounded. We are interested in the question of how the success probability scales when many such games are performed in parallel. We show that any strategy that maximizes the probability to win every game individually is also optimal for the parallel repetition of the game. Our result implies that the optimal guessing probability can be achieved without the use of entanglement. We explore several applications of this result. Firstly, we show that it implies security for standard BB84 quantum key distribution when the receiving party uses fully untrusted measurement devices, i.e. we show that BB84 is one-sided device independent. Secondly, we show how our result can be used to prove security of a one-round position-verification scheme. Finally, we generalize a well-known uncertainty relation for the guessing probability to quantum side information.

  8. Advanced photovoltaic system simulator to demonstrate the performance of advanced photovoltaic cells and devices

    SciTech Connect

    Mrig, L.; DeBlasio, R.; O'Sullivan, G.A.; Tomko, R.P.

    1983-05-01

    This paper describes a photovoltaic system simulator for characterizing and evaluating the performance of advanced photovoltaic cells, modules, and arrays as well as for simulating the operation of advanced conceptual photovoltaic systems. The system simulator is capable of extrapolating the performance from a single laboratory cell, or of a module to power levels up to 10 kW. The major subsystems comprising the system simulator are (1) Solar Array Simulator, (2) Power Conditioning Unit, (3) Load Controller and Resistive Load Unit, (4) Data Acquisition and Control Unit, and (5) Cell Test Bed.

  9. Aircrew Training Devices: Utility and Utilization of Advanced Instructional Features (Phase IV--Summary Report).

    ERIC Educational Resources Information Center

    Polzella, Donald J.; And Others

    Modern aircrew training devices (ATDs) are equipped with sophisticated hardware and software capabilities, known as advanced instructional features (AIFs), that permit a simulator instructor to prepare briefings, manage training, vary task difficulty/fidelity, monitor performance, and provide feedback for flight simulation training missions. The…

  10. Influence of device geometry on tunneling in the ν=(5)/(2) quantum Hall liquid

    NASA Astrophysics Data System (ADS)

    Yang, Guang; Feldman, D. E.

    2013-08-01

    Two recent experiments [Radu , ScienceSCIEAS0036-807510.1126/science.1157560 320, 899 (2008); Lin , Phys. Rev. BPRBMDO1098-012110.1103/PhysRevB.85.165321 85, 165321 (2012)] measured the temperature and voltage dependence of the quasiparticle tunneling through a quantum point contact in the ν=5/2 quantum Hall liquid. The results led to conflicting conclusions about the nature of the quantum Hall state. In this paper, we show that the conflict can be resolved by recognizing different geometries of the devices in the experiments. We argue that in some of those geometries there is significant unscreened electrostatic interaction between the segments of the quantum Hall edge on the opposite sides of the point contact. Coulomb interaction affects the tunneling current. We compare experimental results with theoretical predictions for the Pfaffian, SU(2)2, 331, and K=8 states and their particle-hole conjugates. After Coulomb corrections are taken into account, measurements in all geometries agree with the spin-polarized and spin-unpolarized Halperin 331 states.

  11. Perfectly Matched Layers versus discrete transparent boundary conditions in quantum device simulations

    SciTech Connect

    Mennemann, Jan-Frederik Jüngel, Ansgar

    2014-10-15

    Discrete transparent boundary conditions (DTBC) and the Perfectly Matched Layers (PML) method for the realization of open boundary conditions in quantum device simulations are compared, based on the stationary and time-dependent Schrödinger equation. The comparison includes scattering state, wave packet, and transient scattering state simulations in one and two space dimensions. The Schrödinger equation is discretized by a second-order Crank–Nicolson method in case of DTBC. For the discretization with PML, symmetric second-, fourth-, and sixth-order spatial approximations as well as Crank–Nicolson and classical Runge–Kutta time-integration methods are employed. In two space dimensions, a ring-shaped quantum waveguide device is simulated in the stationary and transient regime. As an application, a simulation of the Aharonov–Bohm effect in this device is performed, showing the excitation of bound states localized in the ring region. The numerical experiments show that the results obtained from PML are comparable to those obtained using DTBC, while keeping the high numerical efficiency and flexibility as well as the ease of implementation of the former method. -- Highlights: •In-depth comparison between discrete transparent boundary conditions (DTBC) and PML. •First 2-D transient scattering state simulations using DTBC. •First 2-D transient scattering state simulations of the Aharonov–Bohm effect.

  12. Phase-Reference-Free Experiment of Measurement-Device-Independent Quantum Key Distribution.

    PubMed

    Wang, Chao; Song, Xiao-Tian; Yin, Zhen-Qiang; Wang, Shuang; Chen, Wei; Zhang, Chun-Mei; Guo, Guang-Can; Han, Zheng-Fu

    2015-10-16

    Measurement-device-independent quantum key distribution (MDI QKD) is a substantial step toward practical information-theoretic security for key sharing between remote legitimate users (Alice and Bob). As with other standard device-dependent quantum key distribution protocols, such as BB84, MDI QKD assumes that the reference frames have been shared between Alice and Bob. In practice, a nontrivial alignment procedure is often necessary, which requires system resources and may significantly reduce the secure key generation rate. Here, we propose a phase-coding reference-frame-independent MDI QKD scheme that requires no phase alignment between the interferometers of two distant legitimate parties. As a demonstration, a proof-of-principle experiment using Faraday-Michelson interferometers is presented. The experimental system worked at 1 MHz, and an average secure key rate of 8.309 bps was obtained at a fiber length of 20 km between Alice and Bob. The system can maintain a positive key generation rate without phase compensation under normal conditions. The results exhibit the feasibility of our system for use in mature MDI QKD devices and its value for network scenarios. PMID:26550855

  13. High-efficiency red electroluminescent device based on multishelled InP quantum dots.

    PubMed

    Jo, Jung-Ho; Kim, Jong-Hoon; Lee, Ki-Heon; Han, Chang-Yeol; Jang, Eun-Pyo; Do, Young Rag; Yang, Heesun

    2016-09-01

    We report on the synthesis of highly fluorescent red-emitting InP quantum dots (QDs) and their application to the fabrication of a high-efficiency QD-light-emitting diode (QLED). The core/shell heterostructure of the QDs is elaborately tailored toward a multishelled structure with a composition-gradient ZnSeS intermediate shell and an outer ZnS shell. Using the resulting InP/ZnSeS/ZnS QDs as an emitting layer, all-solution-processible red InP QLEDs are fabricated with a hybrid multilayered device structure having an organic hole transport layer (HTL) and an inorganic ZnO nanoparticle electron transport layer. Two HTLs of poly(9-vinlycarbazole) or poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,4'-(N-(4-sec-butylphenyl))diphenyl-amine), whose hole mobilities are different by at least three orders of magnitude, are individually applied for QLED fabrication and such HTL-dependent device performances are compared. Our best red device displays exceptional figures of merit such as a maximum luminance of 2849  cd/m2, a current efficiency of 4.2  cd/A, and an external quantum efficiency of 2.5%. PMID:27607953

  14. Large thermoelectric power and figure of merit in a ferromagnetic-quantum dot-superconducting device

    NASA Astrophysics Data System (ADS)

    Hwang, Sun-Yong; López, Rosa; Sánchez, David

    2016-08-01

    We investigate the thermoelectric properties of a quantum dot coupled to ferromagnetic and superconducting electrodes. The combination of spin polarized tunneling at the ferromagnetic-quantum dot interface and the application of an external magnetic field that Zeeman splits the dot energy level leads to large values of the thermopower (Seebeck coefficient). Importantly, the thermopower can be tuned with an external gate voltage connected to the dot. We compute the figure of merit that measures the efficiency of thermoelectric conversion and find that it attains high values. We discuss the different contributions from Andreev reflection processes and quasiparticle tunneling into and out of the superconducting contact. Furthermore, we obtain dramatic variations of both the magnetothermopower and the spin Seebeck effect, which suggest that in our device spin currents can be controlled with temperature gradients only.

  15. Modulating the band gap of germanane nanoribbons for quantum well devices.

    PubMed

    Zhou, Yungang; Li, Xuemei; Wang, Zhiguo; Li, Sean; Zu, Xiaotao

    2014-09-01

    The effective modulation of the band gaps in nanostructures is of both fundamental and technological interest because a tunable band gap gives great flexibility in the design and optimization of nanodevices. Using density functional theory calculations, we have shown that germanane nanoribbons of various widths or under various strains can provide rich band gaps. Width- and strain-induced changes in the band gaps of germanane nanoribbons result from a reduction in quantum confinement with width and the weakening of sp(3) hybridization with strain, respectively. Both changes represent a monotonous relationship. To utilize such a monotonous change in band gap, we designed a quantum well based on germanane nanoribbons in which photoexcited electrons and holes occupy the same spatial region, resulting in a desirable light-emitting device. PMID:25051154

  16. Recent Advances in Organic Photovoltaics: Device Structure and Optical Engineering Optimization on the Nanoscale.

    PubMed

    Luo, Guoping; Ren, Xingang; Zhang, Su; Wu, Hongbin; Choy, Wallace C H; He, Zhicai; Cao, Yong

    2016-03-23

    Organic photovoltaic (OPV) devices, which can directly convert absorbed sunlight to electricity, are stacked thin films of tens to hundreds of nanometers. They have emerged as a promising candidate for affordable, clean, and renewable energy. In the past few years, a rapid increase has been seen in the power conversion efficiency of OPV devices toward 10% and above, through comprehensive optimizations via novel photoactive donor and acceptor materials, control of thin-film morphology on the nanoscale, device structure developments, and interfacial and optical engineering. The intrinsic problems of short exciton diffusion length and low carrier mobility in organic semiconductors creates a challenge for OPV designs for achieving optically thick and electrically thin device structures to achieve sufficient light absorption and efficient electron/hole extraction. Recent advances in the field of OPV devices are reviewed, with a focus on the progress in device architecture and optical engineering approaches that lead to improved electrical and optical characteristics in OPV devices. Successful strategies are highlighted for light wave distribution, modulation, and absorption promotion inside the active layer of OPV devices by incorporating periodic nanopatterns/nanostructures or incorporating metallic nanomaterials and nanostructures. PMID:26856789

  17. Design of 4-electrode optical device for application of vector electric fields to self-assembled quantum dot complexes

    SciTech Connect

    Zhou, Xinran; Doty, Matthew

    2014-10-28

    Self-assembled InAs quantum dots (QDs) are of great interest as components of optoelectronic devices that can operate at the quantum limit. The charge configuration, interdot coupling, and symmetry of complexes containing multiple QDs can all be tuned with applied electric fields, but the magnitude and angle of the electric field required to control each of these parameters depend on the orientation of the QD complex. We present a 4-electrode device compatible with optical excitation and emission that allows application of electric fields with arbitrary magnitudes and angles relative to isolated QD complexes. We demonstrate the electric field tunability of this device with numerical simulations.

  18. Quantum Hall resistance standard in graphene devices under relaxed experimental conditions.

    PubMed

    Ribeiro-Palau, R; Lafont, F; Brun-Picard, J; Kazazis, D; Michon, A; Cheynis, F; Couturaud, O; Consejo, C; Jouault, B; Poirier, W; Schopfer, F

    2015-11-01

    The quantum Hall effect provides a universal standard for electrical resistance that is theoretically based on only the Planck constant h and the electron charge e. Currently, this standard is implemented in GaAs/AlGaAs, but graphene's electronic properties have given hope for a more practical device. Here, we demonstrate that the experimental conditions necessary for the operation of devices made of high-quality graphene grown by chemical vapour deposition on silicon carbide can be extended and significantly relaxed compared with those for state-of-the-art GaAs/AlGaAs devices. In particular, the Hall resistance can be accurately quantized to within 1 × 10(-9) over a 10 T wide range of magnetic flux density, down to 3.5 T, at a temperature of up to 10 K or with a current of up to 0.5 mA. This experimental simplification highlights the great potential of graphene in the development of user-friendly and versatile quantum standards that are compatible with broader industrial uses beyond those in national metrology institutes. Furthermore, the measured agreement of the quantized Hall resistance in graphene and GaAs/AlGaAs, with an ultimate uncertainty of 8.2 × 10(-11), supports the universality of the quantum Hall effect. This also provides evidence of the relation of the quantized Hall resistance with h and e, which is crucial for the new Système International d'unités to be based on fixing such fundamental constants of nature. PMID:26344181

  19. Quantum Hall resistance standard in graphene devices under relaxed experimental conditions

    NASA Astrophysics Data System (ADS)

    Ribeiro-Palau, R.; Lafont, F.; Brun-Picard, J.; Kazazis, D.; Michon, A.; Cheynis, F.; Couturaud, O.; Consejo, C.; Jouault, B.; Poirier, W.; Schopfer, F.

    2015-11-01

    The quantum Hall effect provides a universal standard for electrical resistance that is theoretically based on only the Planck constant h and the electron charge e. Currently, this standard is implemented in GaAs/AlGaAs, but graphene's electronic properties have given hope for a more practical device. Here, we demonstrate that the experimental conditions necessary for the operation of devices made of high-quality graphene grown by chemical vapour deposition on silicon carbide can be extended and significantly relaxed compared with those for state-of-the-art GaAs/AlGaAs devices. In particular, the Hall resistance can be accurately quantized to within 1 × 10-9 over a 10 T wide range of magnetic flux density, down to 3.5 T, at a temperature of up to 10 K or with a current of up to 0.5 mA. This experimental simplification highlights the great potential of graphene in the development of user-friendly and versatile quantum standards that are compatible with broader industrial uses beyond those in national metrology institutes. Furthermore, the measured agreement of the quantized Hall resistance in graphene and GaAs/AlGaAs, with an ultimate uncertainty of 8.2 × 10-11, supports the universality of the quantum Hall effect. This also provides evidence of the relation of the quantized Hall resistance with h and e, which is crucial for the new Système International d'unités to be based on fixing such fundamental constants of nature.

  20. An advanced photovoltaic system simulator to demonstrate the performance of advanced photovoltaic cells and devices

    SciTech Connect

    Mrig, L.; DeBlasio, R.; O'Sullivan, G.A.; Tomko, R.P.

    1982-09-01

    This paper describes a photovoltaic system simulator for characterizing and evaluating the performance of advanced photovoltaic cells, modules, and arrays as well as for simulating the operation of advanced conceptual photovoltaic systems. The system simulator is capable of extrapolating the performance from a single laboratory cell, or of a module to power levels up to 10 kw. The major subsystems comprising the system simulator are Solar Array Simulator, Power Conditioning Unit, Load Controller and Resistive Load Unit, Data Acquisition and Control Unit, and Cell Test Bed. The system was designed and fabricated by Abacus Controls, Inc., Somerville, NJ, under subcontract to SERI, and has recently been installed (except the cell test bed) at SERI, where initial operation is taking place.

  1. A review of III-nitride research at the Center for Quantum Devices

    NASA Astrophysics Data System (ADS)

    Razeghi, M.; McClintock, R.

    2009-05-01

    In this paper, we review the history of the Center for Quantum Devices' (CQD) III-nitride research covering the past 15 years. We review early work developing III-nitride material growth. We then present a review of laser and light-emitting diode (LED) results covering everything from blue lasers to deep UV LEDs emitting at 250 nm. This is followed by a discussion of our UV photodetector research from early photoconductors all the way to current state of the art Geiger-mode UV single photon detectors.

  2. Measurement of the dynamic input impedance of a dc superconducting quantum interference device at audio frequencies

    SciTech Connect

    Falferi, P.; Mezzena, R.; Vitale, S.; Cerdonio, M.

    1997-08-01

    The coupling effects of a commercial dc superconducting quantum interference device (SQUID) to an electrical LC resonator which operates at audio frequencies ({approx}1kHz) with quality factors Q{approx}10{sup 6} are presented. The variations of the resonance frequency of the resonator as functions of the flux applied to the SQUID are due to the SQUID dynamic inductance in good agreement with the predictions of a model. The variations of the quality factor point to a feedback mechanism between the output of the SQUID and the input circuit. {copyright} {ital 1997 American Institute of Physics.}

  3. An enhanced proposal on decoy-state measurement device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Wang, Qin; Zhang, Chun-Hui; Luo, Shunlong; Guo, Guang-Can

    2016-06-01

    By employing pulses involving three-intensity, we propose a scheme for the measurement device-independent quantum key distribution with heralded single-photon sources. We make a comparative study of this scheme with the standard three-intensity decoy-state scheme using weak coherent sources or heralded single-photon sources. The advantage of this scheme is illustrated through numerical simulations: It can approach very closely the asymptotic case of using an infinite number of decoy-states and exhibits excellent behavior in both the secure transmission distance and the final key generation rate.

  4. Development of superconducting contacts for the CRESST II 66-channel superconducting quantum interference device readout system.

    PubMed

    Majorovits, B; Henry, S; Kraus, H

    2007-07-01

    The CRESST experiment is designed to search for weakly interacting massive particle dark matter with cryogenic detectors. CRESST II will use up to 33 CaWO(4) crystals with a total mass of approximately 10 kg. These many detectors require a readout system based on 66-channel superconducting quantum interference devices (SQUIDs). In this article we report on the development of a modular superconducting connector for the 66-channel SQUID readout circuit. We show that the technique developed reliably produces superconducting contacts. PMID:17672757

  5. Development of superconducting contacts for the CRESST II 66-channel superconducting quantum interference device readout system

    SciTech Connect

    Majorovits, B.; Henry, S.; Kraus, H.

    2007-07-15

    The CRESST experiment is designed to search for weakly interacting massive particle dark matter with cryogenic detectors. CRESST II will use up to 33 CaWO{sub 4} crystals with a total mass of {approx}10 kg. These many detectors require a readout system based on 66-channel superconducting quantum interference devices (SQUIDs). In this article we report on the development of a modular superconducting connector for the 66-channel SQUID readout circuit. We show that the technique developed reliably produces superconducting contacts.

  6. Quantum transport measurement of few-layer WTe2 field effect devices

    NASA Astrophysics Data System (ADS)

    Chen, Jianhao; Liu, Xin; Tian, Shibing; Zhang, Chenglong; Jia, Shuang

    2015-03-01

    We have performed systematic quantum transport measurement on field effect devices fabricated from few-layer WTe2 single crystals. We found that the magnetoresistance of few-layer WTe2 could be very different from that of bulk samples, which may arise from the imbalance of electron and hole carriers in the samples. We shall discuss our findings in more details in light of recent progress in our experiment. This work is supported by National Natural Science Foundation of China (11374021 and 11327406); by China Ministry of Science and Technology under Contract # 2014CB920900 and 2013CB921900; and by the Young 1000-Talent Program of China.

  7. Making the decoy-state measurement-device-independent quantum key distribution practically useful

    NASA Astrophysics Data System (ADS)

    Zhou, Yi-Heng; Yu, Zong-Wen; Wang, Xiang-Bin

    2016-04-01

    The relatively low key rate seems to be the major barrier to its practical use for the decoy-state measurement-device-independent quantum key distribution (MDI-QKD). We present a four-intensity protocol for the decoy-state MDI-QKD that hugely raises the key rate, especially in the case in which the total data size is not large. Also, calculations show that our method makes it possible for secure private communication with fresh keys generated from MDI-QKD with a delay time of only a few seconds.

  8. Iii-V Compound Multiple Quantum Well Based Modulator and Switching Devices.

    NASA Astrophysics Data System (ADS)

    Hong, Songcheol

    A general formalism to study the absorption and photocurrent in multiple quantum well is provided with detailed consideration of quantum confined Stark shift, exciton binding energy, line broadening, tunneling, polarization, and strain effects. Results on variation of exciton size, binding energies and transition energies as a function electric field and well size have been presented. Inhomogeneous line broadening of exciton lines due to interface roughness, alloy disorder and well to well size fluctuation is calculated. The potential of material tailoring by introducing strain for specific optical response is discussed. Theoretical and experimental results on excitonic and band-to-band absorption spectra in strained multi-quantum well structures are shown. I also report on polarization dependent optical absorption for excitonic and interband transitions in lattice matched and strained multiquantum well structures in presence of transverse electric field. Photocurrent in a p-i(MQW)-n diode with monochromatic light is examined with respect to different temperatures and intensities. The negative resistance of I-V characteristic of the p-i-n diode is based on the quantum confined Stark effect of the heavy hole excitonic transition in a multiquantum well. This exciton based photocurrent characteristic allows efficient switching. A general purpose low power optical logic device using the controller-modulator concept bas been proposed and realized. The controller is a heterojunction phototransistor with multiquantum wells in the base-collector depletion region. This allows an amplified photocurrent controlled voltage feedback with low light intensity levels. Detailed analysis of the sensitivity of this device in various modes of operation is studied. Studies are also presented on the cascadability of the device as well as its integrating -thresholding properties. A multiquantum well heterojunction bipolar transistor (MHBT), which has N^+ -p^+-i(MQW)-N structure has been

  9. Homoclinic and chaotic transitions in the rf (radio frequency) superconducting quantum interference device (SQUID). Presentation paper

    SciTech Connect

    Jacobs, E.W.; Bulsara, A.R.; Schieve, W.C.

    1989-06-01

    We consider a simple model of the flux in an rf superconducting quantum-interference device (SQUID) subjected to an external periodic magnetic field. The dynamic equation describing the flux response of the SQUID is solved analytically in the absence of damping and external driving terms. These terms are then introduced as perturbations, and the Melnikov function for the system is constructed. The transition from periodic to chaotic behavior is studied through a calculation of the Lyapunov exponents for the systems, and the dimension of the strange attracting set is calculated.

  10. Gate-tunable superconducting quantum interference devices of PbS nanowires

    NASA Astrophysics Data System (ADS)

    Kim, Hong-Seok; Kim, Bum-Kyu; Yang, Yiming; Peng, Xingyue; Lee, Soon-Gul; Yu, Dong; Doh, Yong-Joo

    2016-02-01

    We report on the fabrication and electrical transport properties of gate-tunable superconducting quantum interference devices (SQUIDs), made from a semiconducting PbS nanowire contacted with PbIn superconducting electrodes. With a magnetic field applied perpendicular to the plane of the nanohybrid SQUID, periodic oscillations of the critical current due to the flux quantization in SQUID are observed up to T = 4.0 K. A nonsinusoidal current-phase relationship is obtained as a function of temperature and gate voltage, which is consistent with a short and diffusive junction model.

  11. Reversibility Of Superconducting Nb Weak Links Driven By The Proximity Effect In A Quantum Interference Device

    NASA Astrophysics Data System (ADS)

    Kumar, Nikhil; Fournier, T.; Courtois, H.; Winkelmann, C. B.; Gupta, Anjan K.

    2015-04-01

    We demonstrate the role of the proximity effect in the thermal hysteresis of superconducting constrictions. From the analysis of successive thermal instabilities in the transport characteristics of micron-size superconducting quantum interference devices with a well-controlled geometry, we obtain a complete picture of the different thermal regimes. These determine whether or not the junctions are hysteretic. Below the superconductor critical temperature, the critical current switches from a classical weak-link behavior to one driven by the proximity effect. The associated small amplitude of the critical current makes it robust with respect to the heat generation by phase slips, leading to a nonhysteretic behavior.

  12. Loss-tolerant measurement-device-independent quantum random number generation

    NASA Astrophysics Data System (ADS)

    Cao, Zhu; Zhou, Hongyi; Ma, Xiongfeng

    2015-12-01

    Quantum random number generators (QRNGs) output genuine random numbers based upon the uncertainty principle. A QRNG contains two parts in general—a randomness source and a readout detector. How to remove detector imperfections has been one of the most important questions in practical randomness generation. We propose a simple solution, measurement-device-independent QRNG, which not only removes all detector side channels but is robust against losses. In contrast to previous fully device-independent QRNGs, our scheme does not require high detector efficiency or nonlocality tests. Simulations show that our protocol can be implemented efficiently with a practical coherent state laser and other standard optical components. The security analysis of our QRNG consists mainly of two parts: measurement tomography and randomness quantification, where several new techniques are developed to characterize the randomness associated with a positive-operator valued measure.

  13. Superconducting quantum interference device microsusceptometer balanced over a wide bandwidth for nuclear magnetic resonance applications

    SciTech Connect

    Vinante, A. Falferi, P.; Mezzena, R.

    2014-10-15

    Superconducting Quantum Interference Device (SQUID) microsusceptometers have been widely used to study magnetic properties of materials at microscale. As intrinsically balanced devices, they could also be exploited for direct SQUID-detection of nuclear magnetic resonance (NMR) from micron sized samples, or for SQUID readout of mechanically detected NMR from submicron sized samples. Here, we demonstrate a double balancing technique that enables achievement of very low residual imbalance of a SQUID microsusceptometer over a wide bandwidth. In particular, we can generate ac magnetic fields within the SQUID loop as large as 1 mT, for frequencies ranging from dc up to a few MHz. As an application, we demonstrate direct detection of NMR from {sup 1}H spins in a glycerol droplet placed directly on top of the 20 μm SQUID loops.

  14. Subgap resonant quasiparticle transport in normal-superconductor quantum dot devices

    NASA Astrophysics Data System (ADS)

    Gramich, J.; Baumgartner, A.; Schönenberger, C.

    2016-04-01

    We report thermally activated transport resonances for biases below the superconducting energy gap in a carbon nanotube quantum dot (QD) device with a superconducting Pb and a normal metal contact. These resonances are due to the superconductor's finite quasi-particle population at elevated temperatures and can only be observed when the QD life-time broadening is considerably smaller than the gap. This condition is fulfilled in our QD devices with optimized Pd/Pb/In multi-layer contacts, which result in reproducibly large and "clean" superconducting transport gaps with a strong conductance suppression for subgap biases. We show that these gaps close monotonically with increasing magnetic field and temperature. The accurate description of the subgap resonances by a simple resonant tunneling model illustrates the ideal characteristics of the reported Pb contacts and gives an alternative access to the tunnel coupling strengths in a QD.

  15. Multi-scale quantum point contact model for filamentary conduction in resistive random access memories devices

    SciTech Connect

    Lian, Xiaojuan Cartoixà, Xavier; Miranda, Enrique; Suñé, Jordi; Perniola, Luca; Rurali, Riccardo; Long, Shibing; Liu, Ming

    2014-06-28

    We depart from first-principle simulations of electron transport along paths of oxygen vacancies in HfO{sub 2} to reformulate the Quantum Point Contact (QPC) model in terms of a bundle of such vacancy paths. By doing this, the number of model parameters is reduced and a much clearer link between the microscopic structure of the conductive filament (CF) and its electrical properties can be provided. The new multi-scale QPC model is applied to two different HfO{sub 2}-based devices operated in the unipolar and bipolar resistive switching (RS) modes. Extraction of the QPC model parameters from a statistically significant number of CFs allows revealing significant structural differences in the CF of these two types of devices and RS modes.

  16. Improved superconducting quantum interference device magnetometer for low cross talk operation

    NASA Astrophysics Data System (ADS)

    Granata, C.; Vettoliere, A.; Russo, M.

    2006-05-01

    A fully integrated dc-SQUID (superconducting quantum interference device) magnetometer based on niobium technology including a new feedback coil design is presented. With respect to a standard SQUID design, the new feedback coil design was optimized in order to reduce the mutual inductance between neighbors and to increase the coupling with the pickup coil of the SQUID itself. In such a way, it is possible to reduce cross talk due to both the feedback coil and wires. Experimental results for the characterization of the device and the cross talk measurements are reported. The measurements have been performed in liquid helium using a low noise readout electronics specifically designed for large multichannel SQUID-based instruments. The experimental data show a substantial reduction of cross talk between neighboring sensors with respect to a traditional feedback coil. Furthermore, the new feedback coil system does not introduce any noise degradation.

  17. AN ADVANCED CALIBRATION PROCEDURE FOR COMPLEX IMPEDANCE SPECTRUM MEASUREMENTS OF ADVANCED ENERGY STORAGE DEVICES

    SciTech Connect

    William H. Morrison; Jon P. Christophersen; Patrick Bald; John L. Morrison

    2012-06-01

    With the increasing demand for electric and hybrid electric vehicles and the explosion in popularity of mobile and portable electronic devices such as laptops, cell phones, e-readers, tablet computers and the like, reliance on portable energy storage devices such as batteries has likewise increased. The concern for the availability of critical systems in turn drives the availability of battery systems and thus the need for accurate battery health monitoring has become paramount. Over the past decade the Idaho National Laboratory (INL), Montana Tech of the University of Montana (Tech), and Qualtech Systems, Inc. (QSI) have been developing the Smart Battery Status Monitor (SBSM), an integrated battery management system designed to monitor battery health, performance and degradation and use this knowledge for effective battery management and increased battery life. Key to the success of the SBSM is an in-situ impedance measurement system called the Impedance Measurement Box (IMB). One of the challenges encountered has been development of an accurate, simple, robust calibration process. This paper discusses the successful realization of this process.

  18. Recent advances in medical device triage technologies for chemical, biological, radiological, and nuclear events.

    PubMed

    Lansdowne, Krystal; Scully, Christopher G; Galeotti, Loriano; Schwartz, Suzanne; Marcozzi, David; Strauss, David G

    2015-06-01

    In 2010, the US Food and Drug Administration (Silver Spring, Maryland USA) created the Medical Countermeasures Initiative with the mission of development and promoting medical countermeasures that would be needed to protect the nation from identified, high-priority chemical, biological, radiological, or nuclear (CBRN) threats and emerging infectious diseases. The aim of this review was to promote regulatory science research of medical devices and to analyze how the devices can be employed in different CBRN scenarios. Triage in CBRN scenarios presents unique challenges for first responders because the effects of CBRN agents and the clinical presentations of casualties at each triage stage can vary. The uniqueness of a CBRN event can render standard patient monitoring medical device and conventional triage algorithms ineffective. Despite the challenges, there have been recent advances in CBRN triage technology that include: novel technologies; mobile medical applications ("medical apps") for CBRN disasters; electronic triage tags, such as eTriage; diagnostic field devices, such as the Joint Biological Agent Identification System; and decision support systems, such as the Chemical Hazards Emergency Medical Management Intelligent Syndromes Tool (CHEMM-IST). Further research and medical device validation can help to advance prehospital triage technology for CBRN events. PMID:25868677

  19. Quantum interference measurement of spin interactions in a bio-organic/semiconductor device structure

    SciTech Connect

    Deo, Vincent; Zhang, Yao; Soghomonian, Victoria; Heremans, Jean J.

    2015-03-30

    Quantum interference is used to measure the spin interactions between an InAs surface electron system and the iron center in the biomolecule hemin in nanometer proximity in a bio-organic/semiconductor device structure. The interference quantifies the influence of hemin on the spin decoherence properties of the surface electrons. The decoherence times of the electrons serve to characterize the biomolecule, in an electronic complement to the use of spin decoherence times in magnetic resonance. Hemin, prototypical for the heme group in hemoglobin, is used to demonstrate the method, as a representative biomolecule where the spin state of a metal ion affects biological functions. The electronic determination of spin decoherence properties relies on the quantum correction of antilocalization, a result of quantum interference in the electron system. Spin-flip scattering is found to increase with temperature due to hemin, signifying a spin exchange between the iron center and the electrons, thus implying interactions between a biomolecule and a solid-state system in the hemin/InAs hybrid structure. The results also indicate the feasibility of artificial bioinspired materials using tunable carrier systems to mediate interactions between biological entities.

  20. Quantum interference measurement of spin interactions in a bio-organic/semiconductor device structure

    DOE PAGESBeta

    Deo, Vincent; Zhang, Yao; Soghomonian, Victoria; Heremans, Jean J.

    2015-03-30

    Quantum interference is used to measure the spin interactions between an InAs surface electron system and the iron center in the biomolecule hemin in nanometer proximity in a bio-organic/semiconductor device structure. The interference quantifies the influence of hemin on the spin decoherence properties of the surface electrons. The decoherence times of the electrons serve to characterize the biomolecule, in an electronic complement to the use of spin decoherence times in magnetic resonance. Hemin, prototypical for the heme group in hemoglobin, is used to demonstrate the method, as a representative biomolecule where the spin state of a metal ion affects biologicalmore » functions. The electronic determination of spin decoherence properties relies on the quantum correction of antilocalization, a result of quantum interference in the electron system. Spin-flip scattering is found to increase with temperature due to hemin, signifying a spin exchange between the iron center and the electrons, thus implying interactions between a biomolecule and a solid-state system in the hemin/InAs hybrid structure. The results also indicate the feasibility of artificial bioinspired materials using tunable carrier systems to mediate interactions between biological entities.« less

  1. Quantum interference measurement of spin interactions in a bio-organic/semiconductor device structure

    NASA Astrophysics Data System (ADS)

    Deo, Vincent; Zhang, Yao; Soghomonian, Victoria; Heremans, Jean J.

    2015-03-01

    Quantum interference is used to measure the spin interactions between an InAs surface electron system and the iron center in the biomolecule hemin in nanometer proximity in a bio-organic/semiconductor device structure. The interference quantifies the influence of hemin on the spin decoherence properties of the surface electrons. The decoherence times of the electrons serve to characterize the biomolecule, in an electronic complement to the use of spin decoherence times in magnetic resonance. Hemin, prototypical for the heme group in hemoglobin, is used to demonstrate the method, as a representative biomolecule where the spin state of a metal ion affects biological functions. The electronic determination of spin decoherence properties relies on the quantum correction of antilocalization, a result of quantum interference in the electron system. Spin-flip scattering is found to increase with temperature due to hemin, signifying a spin exchange between the iron center and the electrons, thus implying interactions between a biomolecule and a solid-state system in the hemin/InAs hybrid structure. The results also indicate the feasibility of artificial bioinspired materials using tunable carrier systems to mediate interactions between biological entities.

  2. Light-Emitting Devices Based on Top-down Fabricated GaAs Quantum Nanodisks

    PubMed Central

    Higo, Akio; Kiba, Takayuki; Tamura, Yosuke; Thomas, Cedric; Takayama, Junichi; Wang, Yunpeng; Sodabanlu, Hassanet; Sugiyama, Masakazu; Nakano, Yoshiaki; Yamashita, Ichiro; Murayama, Akihiro; Samukawa, Seiji

    2015-01-01

    Quantum dots photonic devices based on the III–V compound semiconductor technology offer low power consumption, temperature stability, and high-speed modulation. We fabricated GaAs nanodisks (NDs) of sub-20-nm diameters by a top-down process using a biotemplate and neutral beam etching (NBE). The GaAs NDs were embedded in an AlGaAs barrier regrown by metalorganic vapor phase epitaxy (MOVPE). The temperature dependence of photoluminescence emission energies and the transient behavior were strongly affected by the quantum confinement effects of the embedded NDs. Therefore, the quantum levels of the NDs may be tuned by controlling their dimensions. We combined NBE and MOVPE in a high-throughput process compatible with industrial production systems to produce GaAs NDs with tunable optical characteristics. ND light emitting diode exhibited a narrow spectral width of 38 nm of high-intensity emission as a result of small deviation of ND sizes and superior crystallographic quality of the etched GaAs/AlGaAs layer. PMID:25792119

  3. Light-Emitting Devices Based on Top-down Fabricated GaAs Quantum Nanodisks

    NASA Astrophysics Data System (ADS)

    Higo, Akio; Kiba, Takayuki; Tamura, Yosuke; Thomas, Cedric; Takayama, Junichi; Wang, Yunpeng; Sodabanlu, Hassanet; Sugiyama, Masakazu; Nakano, Yoshiaki; Yamashita, Ichiro; Murayama, Akihiro; Samukawa, Seiji

    2015-03-01

    Quantum dots photonic devices based on the III-V compound semiconductor technology offer low power consumption, temperature stability, and high-speed modulation. We fabricated GaAs nanodisks (NDs) of sub-20-nm diameters by a top-down process using a biotemplate and neutral beam etching (NBE). The GaAs NDs were embedded in an AlGaAs barrier regrown by metalorganic vapor phase epitaxy (MOVPE). The temperature dependence of photoluminescence emission energies and the transient behavior were strongly affected by the quantum confinement effects of the embedded NDs. Therefore, the quantum levels of the NDs may be tuned by controlling their dimensions. We combined NBE and MOVPE in a high-throughput process compatible with industrial production systems to produce GaAs NDs with tunable optical characteristics. ND light emitting diode exhibited a narrow spectral width of 38 nm of high-intensity emission as a result of small deviation of ND sizes and superior crystallographic quality of the etched GaAs/AlGaAs layer.

  4. Light-emitting devices based on top-down fabricated GaAs quantum nanodisks.

    PubMed

    Higo, Akio; Kiba, Takayuki; Tamura, Yosuke; Thomas, Cedric; Takayama, Junichi; Wang, Yunpeng; Sodabanlu, Hassanet; Sugiyama, Masakazu; Nakano, Yoshiaki; Yamashita, Ichiro; Murayama, Akihiro; Samukawa, Seiji

    2015-01-01

    Quantum dots photonic devices based on the III-V compound semiconductor technology offer low power consumption, temperature stability, and high-speed modulation. We fabricated GaAs nanodisks (NDs) of sub-20-nm diameters by a top-down process using a biotemplate and neutral beam etching (NBE). The GaAs NDs were embedded in an AlGaAs barrier regrown by metalorganic vapor phase epitaxy (MOVPE). The temperature dependence of photoluminescence emission energies and the transient behavior were strongly affected by the quantum confinement effects of the embedded NDs. Therefore, the quantum levels of the NDs may be tuned by controlling their dimensions. We combined NBE and MOVPE in a high-throughput process compatible with industrial production systems to produce GaAs NDs with tunable optical characteristics. ND light emitting diode exhibited a narrow spectral width of 38 nm of high-intensity emission as a result of small deviation of ND sizes and superior crystallographic quality of the etched GaAs/AlGaAs layer. PMID:25792119

  5. Quantum Hall resistance standard in graphene devices under relaxed experimental conditions

    NASA Astrophysics Data System (ADS)

    Schopfer, F.; Ribeiro-Palau, R.; Lafont, F.; Brun-Picard, J.; Kazazis, D.; Michon, A.; Cheynis, F.; Couturaud, O.; Consejo, C.; Jouault, B.; Poirier, W.

    Large-area and high-quality graphene devices synthesized by CVD on SiC are used to develop reliable electrical resistance standards, based on the quantum Hall effect (QHE), with state-of-the-art accuracy of 1x10-9 and under an extended range of experimental conditions of magnetic field (down to 3.5 T), temperature (up to 10 K) or current (up to 0.5 mA). These conditions are much relaxed as compared to what is required by GaAs/AlGaAs standards and will enable to broaden the use of the primary quantum electrical standards to the benefit of Science and Industry for electrical measurements. Furthermore, by comparison of these graphene devices with GaAs/AlGaAs standards, we demonstrate the universality of the QHE within an ultimate uncertainty of 8.2x10-11. This suggests the exact relation of the quantized Hall resistance with the Planck constant and the electron charge, which is crucial for the new SI to be based on fixing such fundamental constants. These results show that graphene realizes its promises and demonstrates its superiority over other materials for a demanding application. Nature Nanotech. 10, 965-971, 2015, Nature Commun. 6, 6806, 2015

  6. Mid-infrared surface transmitting and detecting quantum cascade device for gas-sensing

    PubMed Central

    Harrer, Andreas; Szedlak, Rolf; Schwarz, Benedikt; Moser, Harald; Zederbauer, Tobias; MacFarland, Donald; Detz, Hermann; Andrews, Aaron Maxwell; Schrenk, Werner; Lendl, Bernhard; Strasser, Gottfried

    2016-01-01

    We present a bi-functional surface emitting and surface detecting mid-infrared device applicable for gas-sensing. A distributed feedback ring quantum cascade laser is monolithically integrated with a detector structured from a bi-functional material for same frequency lasing and detection. The emitted single mode radiation is collimated, back reflected by a flat mirror and detected by the detector element of the sensor. The surface operation mode combined with the low divergence emission of the ring quantum cascade laser enables for long analyte interaction regions spatially separated from the sample surface. The device enables for sensing of gaseous analytes which requires a relatively long interaction region. Our design is suitable for 2D array integration with multiple emission and detection frequencies. Proof of principle measurements with isobutane (2-methylpropane) and propane as gaseous analytes were conducted. Detectable concentration values of 0–70% for propane and 0–90% for isobutane were reached at a laser operation wavelength of 6.5 μm utilizing a 10 cm gas cell in double pass configuration. PMID:26887891

  7. Phase encoding schemes for measurement-device-independent quantum key distribution with basis-dependent flaw

    NASA Astrophysics Data System (ADS)

    Tamaki, Kiyoshi; Lo, Hoi-Kwong; Fung, Chi-Hang Fred; Qi, Bing

    2012-04-01

    In this paper, we study the unconditional security of the so-called measurement-device-independent quantum key distribution (MDIQKD) with the basis-dependent flaw in the context of phase encoding schemes. We propose two schemes for the phase encoding: The first one employs a phase locking technique with the use of non-phase-randomized coherent pulses, and the second one uses conversion of standard Bennett-Brassard 1984 (BB84) phase encoding pulses into polarization modes. We prove the unconditional security of these schemes and we also simulate the key generation rate based on simple device models that accommodate imperfections. Our simulation results show the feasibility of these schemes with current technologies and highlight the importance of the state preparation with good fidelity between the density matrices in the two bases. Since the basis-dependent flaw is a problem not only for MDIQKD but also for standard quantum key distribution (QKD), our work highlights the importance of an accurate signal source in practical QKD systems.

  8. Detection of bacteria in suspension by using a superconducting quantum interference device

    NASA Astrophysics Data System (ADS)

    Grossman, H. L.; Myers, W. R.; Vreeland, V. J.; Bruehl, R.; Alper, M. D.; Bertozzi, C. R.; Clarke, John

    2004-01-01

    We demonstrate a technique for detecting magnetically labeled Listeria monocytogenes and for measuring the binding rate between antibody-linked magnetic particles and bacteria. This sensitive assay quantifies specific bacteria in a sample without the need to immobilize them or wash away unbound magnetic particles. In the measurement, we add 50-nm-diameter superparamagnetic magnetite particles, coated with antibodies, to an aqueous sample containing L. monocytogenes. We apply a pulsed magnetic field to align the magnetic dipole moments and use a high-transition temperature superconducting quantum interference device, an extremely sensitive detector of magnetic flux, to measure the magnetic relaxation signal when the field is turned off. Unbound particles randomize direction by Brownian rotation too quickly to be detected. In contrast, particles bound to L. monocytogenes are effectively immobilized and relax in about 1 s by rotation of the internal dipole moment. This Néel relaxation process is detected by the superconducting quantum interference device. The measurements indicate a detection limit of (5.6 ± 1.1) x 106 L. monocytogenes in our sample volume of 20 µl. If the sample volume were reduced to 1 nl, we estimate that the detection limit could be improved to 230 ± 40 L. monocytogenes cells. Time-resolved measurements yield the binding rate between the particles and bacteria.

  9. Experimental measurement-device-independent quantum key distribution with imperfect sources

    NASA Astrophysics Data System (ADS)

    Tang, Zhiyuan; Wei, Kejin; Bedroya, Olinka; Qian, Li; Lo, Hoi-Kwong

    2016-04-01

    Measurement-device-independent quantum key distribution (MDI-QKD), which is immune to all detector side-channel attacks, is the most promising solution to the security issues in practical quantum key distribution systems. Although several experimental demonstrations of MDI-QKD have been reported, they all make one crucial but not yet verified assumption, that is, there are no flaws in state preparation. Such an assumption is unrealistic and security loopholes remain in the source. Here we present a MDI-QKD experiment with the modulation error taken into consideration. By applying the loss-tolerant security proof by Tamaki et al. [Phys. Rev. A 90, 052314 (2014)], 10.1103/PhysRevA.90.052314, we distribute secure keys over fiber links up to 40 km with imperfect sources, which would not have been possible under previous security proofs. By simultaneously closing loopholes at the detectors and a critical loophole—modulation error in the source, our work shows the feasibility of secure QKD with practical imperfect devices.

  10. Mid-infrared surface transmitting and detecting quantum cascade device for gas-sensing

    NASA Astrophysics Data System (ADS)

    Harrer, Andreas; Szedlak, Rolf; Schwarz, Benedikt; Moser, Harald; Zederbauer, Tobias; Macfarland, Donald; Detz, Hermann; Andrews, Aaron Maxwell; Schrenk, Werner; Lendl, Bernhard; Strasser, Gottfried

    2016-02-01

    We present a bi-functional surface emitting and surface detecting mid-infrared device applicable for gas-sensing. A distributed feedback ring quantum cascade laser is monolithically integrated with a detector structured from a bi-functional material for same frequency lasing and detection. The emitted single mode radiation is collimated, back reflected by a flat mirror and detected by the detector element of the sensor. The surface operation mode combined with the low divergence emission of the ring quantum cascade laser enables for long analyte interaction regions spatially separated from the sample surface. The device enables for sensing of gaseous analytes which requires a relatively long interaction region. Our design is suitable for 2D array integration with multiple emission and detection frequencies. Proof of principle measurements with isobutane (2-methylpropane) and propane as gaseous analytes were conducted. Detectable concentration values of 0-70% for propane and 0-90% for isobutane were reached at a laser operation wavelength of 6.5 μm utilizing a 10 cm gas cell in double pass configuration.

  11. Mid-infrared surface transmitting and detecting quantum cascade device for gas-sensing.

    PubMed

    Harrer, Andreas; Szedlak, Rolf; Schwarz, Benedikt; Moser, Harald; Zederbauer, Tobias; MacFarland, Donald; Detz, Hermann; Andrews, Aaron Maxwell; Schrenk, Werner; Lendl, Bernhard; Strasser, Gottfried

    2016-01-01

    We present a bi-functional surface emitting and surface detecting mid-infrared device applicable for gas-sensing. A distributed feedback ring quantum cascade laser is monolithically integrated with a detector structured from a bi-functional material for same frequency lasing and detection. The emitted single mode radiation is collimated, back reflected by a flat mirror and detected by the detector element of the sensor. The surface operation mode combined with the low divergence emission of the ring quantum cascade laser enables for long analyte interaction regions spatially separated from the sample surface. The device enables for sensing of gaseous analytes which requires a relatively long interaction region. Our design is suitable for 2D array integration with multiple emission and detection frequencies. Proof of principle measurements with isobutane (2-methylpropane) and propane as gaseous analytes were conducted. Detectable concentration values of 0-70% for propane and 0-90% for isobutane were reached at a laser operation wavelength of 6.5 μm utilizing a 10 cm gas cell in double pass configuration. PMID:26887891

  12. Novel Colloidal MoS2 Quantum Dot Heterojunctions on Silicon Platforms for Multifunctional Optoelectronic Devices.

    PubMed

    Mukherjee, Subhrajit; Maiti, Rishi; Katiyar, Ajit K; Das, Soumen; Ray, Samit K

    2016-01-01

    Silicon compatible wafer scale MoS2 heterojunctions are reported for the first time using colloidal quantum dots. Size dependent direct band gap emission of MoS2 dots are presented at room temperature. The temporal stability and decay dynamics of excited charge carriers in MoS2 quantum dots have been studied using time correlated single photon counting spectroscopy technique. Fabricated n-MoS2/p-Si 0D/3D heterojunctions exhibiting excellent rectification behavior have been studied for light emission in the forward bias and photodetection in the reverse bias. The electroluminescences with white light emission spectra in the range of 450-800 nm are found to be stable in the temperature range of 10-350 K. Size dependent spectral responsivity and detectivity of the heterojunction devices have been studied. The peak responsivity and detectivity of the fabricated heterojunction detector are estimated to be ~0.85 A/W and ~8 × 10(11) Jones, respectively at an applied bias of -2 V for MoS2 QDs of 2 nm mean diameter. The above values are found to be superior to the reported results on large area photodetector devices fabricated using two dimensional materials. PMID:27357596

  13. Novel Colloidal MoS2 Quantum Dot Heterojunctions on Silicon Platforms for Multifunctional Optoelectronic Devices

    PubMed Central

    Mukherjee, Subhrajit; Maiti, Rishi; Katiyar, Ajit K.; Das, Soumen; Ray, Samit K.

    2016-01-01

    Silicon compatible wafer scale MoS2 heterojunctions are reported for the first time using colloidal quantum dots. Size dependent direct band gap emission of MoS2 dots are presented at room temperature. The temporal stability and decay dynamics of excited charge carriers in MoS2 quantum dots have been studied using time correlated single photon counting spectroscopy technique. Fabricated n-MoS2/p-Si 0D/3D heterojunctions exhibiting excellent rectification behavior have been studied for light emission in the forward bias and photodetection in the reverse bias. The electroluminescences with white light emission spectra in the range of 450–800 nm are found to be stable in the temperature range of 10–350 K. Size dependent spectral responsivity and detectivity of the heterojunction devices have been studied. The peak responsivity and detectivity of the fabricated heterojunction detector are estimated to be ~0.85 A/W and ~8 × 1011 Jones, respectively at an applied bias of −2 V for MoS2 QDs of 2 nm mean diameter. The above values are found to be superior to the reported results on large area photodetector devices fabricated using two dimensional materials. PMID:27357596

  14. Quantum dots in biomedical applications: advances and challenges

    NASA Astrophysics Data System (ADS)

    Cinteza, Ludmila Otilia

    2010-09-01

    In the past two decades, nanotechnology has made great progress in generating novel materials with superior properties. Quantum dots (QDs) are an example of such materials. With unique optical properties, they have proven to be useful in a wide range of applications in life sciences, especially as a better alternative to overcome the shortcomings of conventional fluorophores. Current progress in the synthesis of biocompatible QDs allows for the possibility of producing a large variety of semiconductor nanocrystals in terms of size, surface functionality, bioconjugation, and targeting facilities. Strategies to enhance the water-dispersibility and biocompatibility of these nanoparticles have been developed, involving various encapsulation techniques and surface functionalization. The major obstacle in the clinical use of QDs remains their toxicity, and the systematic investigation on harmful effects of QDs both to humans and to the environment has become critical. Many examples of the experimental use of QDs prove their far-reaching potential for the study of intracellular processes at the molecular level, high resolution cellular imaging, and in vivo observation of cell trafficking. Biosensing methods based on QD bioconjugates proved to be successful in rapid detection of pathogens, and significant improvements are expected in early cancer diagnostic, non-conventional therapy of cancer and neurodegenerative diseases.

  15. Advanced InSb monolithic Charge Coupled Infrared Imaging Devices (CCIRID)

    NASA Technical Reports Server (NTRS)

    Koch, T. L.; Thom, R. D.; Parrish, W. D.

    1981-01-01

    The continued development of monolithic InSb charge coupled infrared imaging devices (CCIRIDs) is discussed. The processing sequence and structural design of 20-element linear arrays are discussed. Also, results obtained from radiometric testing of the 20-element arrays using a clamped sample-and-hold output circuit are reported. The design and layout of a next-generation CCIRID chip are discussed. The major devices on this chip are a 20 by 16 time-delay-and-integration (TDI) area array and a 100-element linear imaging array. The development of a process for incorporating an ion implanted S(+) planar channel stop into the CCIRID structure and the development of a thin film transparent photogate are also addressed. The transparent photogates will increase quantum efficiency to greater than 70% across the 2.5 to 5.4 micrometer spectral region in future front-side illuminated CCIRIDs.

  16. Recent Advances in Flexible and Stretchable Bio-Electronic Devices Integrated with Nanomaterials.

    PubMed

    Choi, Suji; Lee, Hyunjae; Ghaffari, Roozbeh; Hyeon, Taeghwan; Kim, Dae-Hyeong

    2016-06-01

    Flexible and stretchable electronics and optoelectronics configured in soft, water resistant formats uniquely address seminal challenges in biomedicine. Over the past decade, there has been enormous progress in the materials, designs, and manufacturing processes for flexible/stretchable system subcomponents, including transistors, amplifiers, bio-sensors, actuators, light emitting diodes, photodetector arrays, photovoltaics, energy storage elements, and bare die integrated circuits. Nanomaterials prepared using top-down processing approaches and synthesis-based bottom-up methods have helped resolve the intrinsic mechanical mismatch between rigid/planar devices and soft/curvilinear biological structures, thereby enabling a broad range of non-invasive, minimally invasive, and implantable systems to address challenges in biomedicine. Integration of therapeutic functional nanomaterials with soft bioelectronics demonstrates therapeutics in combination with unconventional diagnostics capabilities. Recent advances in soft materials, devices, and integrated systems are reviewes, with representative examples that highlight the utility of soft bioelectronics for advanced medical diagnostics and therapies. PMID:26779680

  17. Hybrid quantum nanophotonic devices for coupling to rare-earth ions

    NASA Astrophysics Data System (ADS)

    Miyazono, Evan; Hartz, Alex; Zhong, Tian; Faraon, Andrei

    2015-03-01

    With an assortment of narrow line-width transitions spanning the visible and IR spectrum and long spin coherence times, rare-earth doped crystals are the leading material system for solid-state quantum memories. Integrating these materials in an on-chip optical platform would create opportunities for highly integrated light-matter interfaces for quantum communication and quantum computing. Nano-photonic resonators with high quality factors and small mode volumes are required for efficient on-chip coupling to the small dipole moment of rare-earth ion transitions. However, direct fabrication of optical cavities in these crystals with current nanofabrication techniques is difficult and unparallelized, as either exotic etch chemistries or physical milling processes are required. We fabricated hybrid devices by mechanically transferring a nanoscale membrane of gallium arsenide (GaAs) onto a neodymium-doped yttrium silicon oxide (Y2SiO5) crystal and then using electron beam lithography and standard III-V dry etching to pattern nanobeam photonic crystal cavities and ring resonator cavities, a technique that is easily adapted to other frequency ranges for arbitrary dopants in any rare earth host system. Single crystalline GaAs was chosen for its low loss and high refractive index at the transition wavelength. We demonstrated the potential to evanescently couple between the cavity field and the 883 nm 4I9/2- 4F3/2 transition of nearby neodymium impurities in the host crystal by examining transmission spectra through a waveguide coupled to the resonator with a custom-built confocal microscope. The prospects and requirements for using this system for scalable quantum networks are discussed.

  18. Gate-defined quantum dot devices in undoped Si/SiGe heterostructures for spin qubit applications

    NASA Astrophysics Data System (ADS)

    Volk, Christian; Martins, Frederico; Marcus, Charles M.; Kuemmeth, Ferdinand

    Spin qubits based on few electron quantum dots in semiconductor heterostructures are among the most promising systems for realizing quantum computation. Due to its low concentration of nuclear-spin-carrying isotopes, silicon is of special interest as a host material. We characterize gate-defined double and triple quantum dot devices fabricated from undoped Si/Si0.7Ge0.3 heterostructures. Our device architecture is based on integrating all accumulation and depletion mode gates in a single gate layer. This allows us to omit the commonly used global accumulation gate in order to achieve a more local control of the potential landscape in the device. We present our recent progress towards implementing spin qubits in these structures. Support through the EC FP7- ICT project SiSPIN no. 323841, and the Danish National Research Foundation is acknowledged.

  19. Tunable strong nonlinearity of a micromechanical beam embedded in a dc-superconducting quantum interference device

    SciTech Connect

    Ella, Lior Yuvaraj, D.; Suchoi, Oren; Shtempluk, Oleg; Buks, Eyal

    2015-01-07

    We present a study of the controllable nonlinear dynamics of a micromechanical beam coupled to a dc-SQUID (superconducting quantum interference device). The coupling between these systems places the modes of the beam in a highly nonlinear potential, whose shape can be altered by varying the bias current and applied flux of the SQUID. We detect the position of the beam by placing it in an optical cavity, which sets free the SQUID to be used solely for actuation. This enables us to probe the previously unexplored full parameter space of this device. We measure the frequency response of the beam and find that it displays a Duffing oscillator behavior which is periodic in the applied magnetic flux. To account for this, we develop a model based on the standard theory for SQUID dynamics. In addition, with the aim of understanding if the device can reach nonlinearity at the single phonon level, we use this model to show that the responsivity of the current circulating in the SQUID to the position of the beam can become divergent, with its magnitude limited only by noise. This suggests a direction for the generation of macroscopically distinguishable superposition states of the beam.

  20. Tunable strong nonlinearity of a micromechanical beam embedded in a dc-superconducting quantum interference device

    NASA Astrophysics Data System (ADS)

    Ella, Lior; Yuvaraj, D.; Suchoi, Oren; Shtempluk, Oleg; Buks, Eyal

    2015-01-01

    We present a study of the controllable nonlinear dynamics of a micromechanical beam coupled to a dc-SQUID (superconducting quantum interference device). The coupling between these systems places the modes of the beam in a highly nonlinear potential, whose shape can be altered by varying the bias current and applied flux of the SQUID. We detect the position of the beam by placing it in an optical cavity, which sets free the SQUID to be used solely for actuation. This enables us to probe the previously unexplored full parameter space of this device. We measure the frequency response of the beam and find that it displays a Duffing oscillator behavior which is periodic in the applied magnetic flux. To account for this, we develop a model based on the standard theory for SQUID dynamics. In addition, with the aim of understanding if the device can reach nonlinearity at the single phonon level, we use this model to show that the responsivity of the current circulating in the SQUID to the position of the beam can become divergent, with its magnitude limited only by noise. This suggests a direction for the generation of macroscopically distinguishable superposition states of the beam.

  1. Parasitic effects in superconducting quantum interference device-based radiation comb generators

    NASA Astrophysics Data System (ADS)

    Bosisio, R.; Giazotto, F.; Solinas, P.

    2015-12-01

    We study several parasitic effects on the implementation of a Josephson radiation comb generator based on a dc superconducting quantum interference device (SQUID) driven by an external magnetic field. This system can be used as a radiation generator similarly to what is done in optics and metrology, and allows one to generate up to several hundreds of harmonics of the driving frequency. First we take into account how the assumption of a finite loop geometrical inductance and junction capacitance in each SQUID may alter the operation of the devices. Then, we estimate the effect of imperfections in the fabrication of an array of SQUIDs, which is an unavoidable source of errors in practical situations. We show that the role of the junction capacitance is, in general, negligible, whereas the geometrical inductance has a beneficial effect on the performance of the device. The errors on the areas and junction resistance asymmetries may deteriorate the performance, but their effect can be limited to a large extent by a suitable choice of fabrication parameters.

  2. Parasitic effects in superconducting quantum interference device-based radiation comb generators

    SciTech Connect

    Bosisio, R.; Giazotto, F.; Solinas, P.

    2015-12-07

    We study several parasitic effects on the implementation of a Josephson radiation comb generator based on a dc superconducting quantum interference device (SQUID) driven by an external magnetic field. This system can be used as a radiation generator similarly to what is done in optics and metrology, and allows one to generate up to several hundreds of harmonics of the driving frequency. First we take into account how the assumption of a finite loop geometrical inductance and junction capacitance in each SQUID may alter the operation of the devices. Then, we estimate the effect of imperfections in the fabrication of an array of SQUIDs, which is an unavoidable source of errors in practical situations. We show that the role of the junction capacitance is, in general, negligible, whereas the geometrical inductance has a beneficial effect on the performance of the device. The errors on the areas and junction resistance asymmetries may deteriorate the performance, but their effect can be limited to a large extent by a suitable choice of fabrication parameters.

  3. Thermodynamic limits to the conversion of blackbody radiation by quantum systems. [with application to solar energy conversion devices

    NASA Technical Reports Server (NTRS)

    Buoncristiani, A. M.; Smith, B. T.; Byvik, C. E.

    1982-01-01

    Using general thermodynamic arguments, we analyze the conversion of the energy contained in the radiation from a blackbody to useful work by a quantum system. We show that the energy available for conversion is bounded above by the change in free energy in the incident and reradiated fields and that this free energy change depends upon the temperature of the receiving device. Universal efficiency curves giving the ultimate thermodynamic conversion efficiency of the quantum system are presented in terms of the blackbody temperature and the temperature and threshold energy of the quantum system. Application of these results is made to a variety of systems including biological photosynthetic, photovoltaic, and photoelectrochemical systems.

  4. Beyond Advanced Gravitational Wave Detectors: Beating the Quantum Limit with Squeezed States of Light

    NASA Astrophysics Data System (ADS)

    Barsotti, Lisa

    2013-04-01

    After two decades of technology development, the first direct observation of gravitational waves appears to be imminent. Ground-based interferometric gravitational wave detectors world-wide are about to come back on-line after a major upgrade aimed to significantly improve their sensitivity. As these advanced detectors become a reality, the gravitational wave community is looking at new ways of further expanding their astrophysical reach. The quantum nature of light imposes a fundamental limit to the sensitivity that gravitational wave detectors can achieve, due to statistical fluctuations in the arrival time of photons at the interferometer output (shot noise) and the recoil of the mirrors due to radiation pressure noise. In this talk I will show how mature technology can be used to push interferometric precision measurement beyond the standard quantum limit by means of squeezed states of light, and current ideas on how to integrate this technology into the Advanced detectors of the Laser Interferometer Gravitational wave Observatory (LIGO).

  5. Design, Fabrication, and Characterization of Carbon Nanotube Field Emission Devices for Advanced Applications

    NASA Astrophysics Data System (ADS)

    Radauscher, Erich Justin

    Carbon nanotubes (CNTs) have recently emerged as promising candidates for electron field emission (FE) cathodes in integrated FE devices. These nanostructured carbon materials possess exceptional properties and their synthesis can be thoroughly controlled. Their integration into advanced electronic devices, including not only FE cathodes, but sensors, energy storage devices, and circuit components, has seen rapid growth in recent years. The results of the studies presented here demonstrate that the CNT field emitter is an excellent candidate for next generation vacuum microelectronics and related electron emission devices in several advanced applications. The work presented in this study addresses determining factors that currently confine the performance and application of CNT-FE devices. Characterization studies and improvements to the FE properties of CNTs, along with Micro-Electro-Mechanical Systems (MEMS) design and fabrication, were utilized in achieving these goals. Important performance limiting parameters, including emitter lifetime and failure from poor substrate adhesion, are examined. The compatibility and integration of CNT emitters with the governing MEMS substrate (i.e., polycrystalline silicon), and its impact on these performance limiting parameters, are reported. CNT growth mechanisms and kinetics were investigated and compared to silicon (100) to improve the design of CNT emitter integrated MEMS based electronic devices, specifically in vacuum microelectronic device (VMD) applications. Improved growth allowed for design and development of novel cold-cathode FE devices utilizing CNT field emitters. A chemical ionization (CI) source based on a CNT-FE electron source was developed and evaluated in a commercial desktop mass spectrometer for explosives trace detection. This work demonstrated the first reported use of a CNT-based ion source capable of collecting CI mass spectra. The CNT-FE source demonstrated low power requirements, pulsing

  6. Reliability of Strength Testing using the Advanced Resistive Exercise Device and Free Weights

    NASA Technical Reports Server (NTRS)

    English, Kirk L.; Loehr, James A.; Laughlin, Mitzi A.; Lee, Stuart M. C.; Hagan, R. Donald

    2008-01-01

    The Advanced Resistive Exercise Device (ARED) was developed for use on the International Space Station as a countermeasure against muscle atrophy and decreased strength. This investigation examined the reliability of one-repetition maximum (1RM) strength testing using ARED and traditional free weight (FW) exercise. Methods: Six males (180.8 +/- 4.3 cm, 83.6 +/- 6.4 kg, 36 +/- 8 y, mean +/- SD) who had not engaged in resistive exercise for at least six months volunteered to participate in this project. Subjects completed four 1RM testing sessions each for FW and ARED (eight total sessions) using a balanced, randomized, crossover design. All testing using one device was completed before progressing to the other. During each session, 1RM was measured for the squat, heel raise, and deadlift exercises. Generalizability (G) and intraclass correlation coefficients (ICC) were calculated for each exercise on each device and were used to predict the number of sessions needed to obtain a reliable 1RM measurement (G . 0.90). Interclass reliability coefficients and Pearson's correlation coefficients (R) also were calculated for the highest 1RM value (1RM9sub peak)) obtained for each exercise on each device to quantify 1RM relationships between devices.

  7. Optical transmission modules for multi-channel superconducting quantum interference device readouts

    SciTech Connect

    Kim, Jin-Mok Kwon, Hyukchan; Yu, Kwon-kyu; Lee, Yong-Ho; Kim, Kiwoong

    2013-12-15

    We developed an optical transmission module consisting of 16-channel analog-to-digital converter (ADC), digital-noise filter, and one-line serial transmitter, which transferred Superconducting Quantum Interference Device (SQUID) readout data to a computer by a single optical cable. A 16-channel ADC sent out SQUID readouts data with 32-bit serial data of 8-bit channel and 24-bit voltage data at a sample rate of 1.5 kSample/s. A digital-noise filter suppressed digital noises generated by digital clocks to obtain SQUID modulation as large as possible. One-line serial transmitter reformed 32-bit serial data to the modulated data that contained data and clock, and sent them through a single optical cable. When the optical transmission modules were applied to 152-channel SQUID magnetoencephalography system, this system maintained a field noise level of 3 fT/√Hz @ 100 Hz.

  8. Nondestructive Detection of Delamination in Carbon-Fiber-Reinforced Plastics Using Superconducting Quantum Interference Device

    NASA Astrophysics Data System (ADS)

    Hatsukade, Yoshimi; Kasai, Naoko; Ishiyama, Atsushi

    2001-06-01

    The use of carbon-fiber-reinforced plastic (CFRP) in aircraft and space structures is recently increasing. We investigated the possibility of nondestructively detecting a delamination in CFRP using a low-Tc first-order gradiometric superconducting quantum interference device (SQUID) loop. A CFRP plate including a thin insulator sheet between the central layers was prepared. The injected current method was adopted. The magnetic field due to the sheet was measured by a SQUID nondestructive evaluation system using the lock-in detection technique. The position and size of the sheet were successfully detected by mapping the measured field. The result agreed with that by ultrasonic testing. Future application of this method for detecting deep-lying flaws was discussed.

  9. A cryogen-free ultralow-field superconducting quantum interference device magnetic resonance imaging system

    SciTech Connect

    Eom, Byeong Ho; Penanen, Konstantin; Hahn, Inseob

    2014-09-15

    Magnetic resonance imaging (MRI) at microtesla fields using superconducting quantum interference device (SQUID) detection has previously been demonstrated, and advantages have been noted. Although the ultralow-field SQUID MRI technique would not need the heavy superconducting magnet of conventional MRI systems, liquid helium required to cool the low-temperature detector still places a significant burden on its operation. We have built a prototype cryocooler-based SQUID MRI system that does not require a cryogen. The SQUID detector and the superconducting gradiometer were cooled down to 3.7 K and 4.3 K, respectively. We describe the prototype design, characterization, a phantom image, and areas of further improvements needed to bring the imaging performance to parity with conventional MRI systems.

  10. Andreev transport in a correlated ferromagnet-quantum-dot-superconductor device

    NASA Astrophysics Data System (ADS)

    Weymann, I.; Wójcik, K. P.

    2015-12-01

    The spin-resolved Andreev reflection processes in a hybrid ferromagnet-quantum-dot-superconductor device are theoretically studied. In particular, the transport coefficients, such as the Andreev transmission as well as the linear-response Andreev conductance, are calculated by means of the numerical renormalization group method. It is shown that, generally, transport properties are conditioned by the interplay of correlations leading to the Kondo effect, superconducting proximity effect, and ferromagnetic-contact-induced exchange field. The exchange field is shown to greatly affect the low-energy behavior of the Andreev transmission by splitting the Kondo resonance. Moreover, it leads to a nonmonotonic dependence of the Andreev conductance on the dot level position. At low temperatures, the conductance has a peak at the particle-hole symmetry point, which however becomes quickly suppressed with increasing the temperature. The mechanisms responsible for those effects are thoroughly discussed.

  11. Long distance measurement-device-independent quantum key distribution with entangled photon sources

    SciTech Connect

    Xu, Feihu; Qi, Bing; Liao, Zhongfa; Lo, Hoi-Kwong

    2013-08-05

    We present a feasible method that can make quantum key distribution (QKD), both ultra-long-distance and immune, to all attacks in the detection system. This method is called measurement-device-independent QKD (MDI-QKD) with entangled photon sources in the middle. By proposing a model and simulating a QKD experiment, we find that MDI-QKD with one entangled photon source can tolerate 77 dB loss (367 km standard fiber) in the asymptotic limit and 60 dB loss (286 km standard fiber) in the finite-key case with state-of-the-art detectors. Our general model can also be applied to other non-QKD experiments involving entanglement and Bell state measurements.

  12. Optical transmission modules for multi-channel superconducting quantum interference device readouts

    NASA Astrophysics Data System (ADS)

    Kim, Jin-Mok; Kwon, Hyukchan; Yu, Kwon-kyu; Lee, Yong-Ho; Kim, Kiwoong

    2013-12-01

    We developed an optical transmission module consisting of 16-channel analog-to-digital converter (ADC), digital-noise filter, and one-line serial transmitter, which transferred Superconducting Quantum Interference Device (SQUID) readout data to a computer by a single optical cable. A 16-channel ADC sent out SQUID readouts data with 32-bit serial data of 8-bit channel and 24-bit voltage data at a sample rate of 1.5 kSample/s. A digital-noise filter suppressed digital noises generated by digital clocks to obtain SQUID modulation as large as possible. One-line serial transmitter reformed 32-bit serial data to the modulated data that contained data and clock, and sent them through a single optical cable. When the optical transmission modules were applied to 152-channel SQUID magnetoencephalography system, this system maintained a field noise level of 3 fT/√Hz @ 100 Hz.

  13. Optical transmission modules for multi-channel superconducting quantum interference device readouts.

    PubMed

    Kim, Jin-Mok; Kwon, Hyukchan; Yu, Kwon-kyu; Lee, Yong-Ho; Kim, Kiwoong

    2013-12-01

    We developed an optical transmission module consisting of 16-channel analog-to-digital converter (ADC), digital-noise filter, and one-line serial transmitter, which transferred Superconducting Quantum Interference Device (SQUID) readout data to a computer by a single optical cable. A 16-channel ADC sent out SQUID readouts data with 32-bit serial data of 8-bit channel and 24-bit voltage data at a sample rate of 1.5 kSample/s. A digital-noise filter suppressed digital noises generated by digital clocks to obtain SQUID modulation as large as possible. One-line serial transmitter reformed 32-bit serial data to the modulated data that contained data and clock, and sent them through a single optical cable. When the optical transmission modules were applied to 152-channel SQUID magnetoencephalography system, this system maintained a field noise level of 3 fT/√Hz @ 100 Hz. PMID:24387470

  14. Linearized superconducting quantum interference device array for high bandwidth frequency-domain readout multiplexing.

    PubMed

    Lanting, T; Dobbs, M; Spieler, H; Lee, A T; Yamamoto, Y

    2009-09-01

    We have designed and demonstrated a superconducting quantum interference device (SQUID) array linearized with cryogenic feedback. To achieve the necessary loop gain, a 300-element series array SQUID is constructed from three monolithic 100-element series arrays. A feedback resistor completes the loop from the SQUID output to the input coil. The short feedback path of this linearized SQUID array (LISA) allows for a substantially larger flux-locked loop bandwidth as compared to a SQUID flux-locked loop that includes a room temperature amplifier. The bandwidth, linearity, noise performance, and 3 Phi(0) dynamic range of the LISA are sufficient for its use in our target application: the multiplexed readout of transition-edge sensor bolometers. PMID:19791952

  15. Experimental validation of superconducting quantum interference device sensors for electromagnetic scattering in geologic structures

    SciTech Connect

    Krauss, R.H. Jr.; Flynn, E.; Ruminer, P.

    1997-10-01

    This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). This project has supported the collaborative development with Sandia National Laboratories (SNL) and the University of New Mexico (UNM) of two critical components for a hand-held low-field magnetic sensor based on superconducting quantum interference device (SQUID) sensor technology. The two components are a digital signal processing (DSP) algorithm for background noise rejection and a small hand-held dewar cooled by a cryocooler. A hand-held sensor has been designed and fabricated for detection of extremely weak magnetic fields in unshielded environments. The sensor is capable of measuring weak magnetic fields in unshielded environments and has multiple applications. We have chosen to pursue battlefield medicine as the highest probability near-term application because of stated needs of several agencies.

  16. Compensation techniques for high-temperature superconducting quantum interference device gradiometers operating in unshielded environment

    NASA Astrophysics Data System (ADS)

    Borgmann, J.; David, P.; Krause, H. J.; Otto, R.; Braginski, A. I.

    1997-08-01

    We have tested two methods of compensating environmental disturbances applicable to high-temperature superconducting quantum interference device (SQUID) systems operating in magnetically unshielded environments. For testing, we used first- and second-order axial electronic gradiometer setups with rf SQUID magnetometers operating at 77 K and base lines between 7 and 8 cm. The magnetometers were single-layer washer rf SQUIDs with bulk or thin-film magnetic flux concentrators in flip-chip geometry. The tested methods resulted in disturbance compensation levels comparable to those attained using electronically formed gradiometers. The white noise of the compensated magnetometers resulted in 13.5 fT/cm √Hz for first-order and 22 fT/cm2 √Hz for second-order compensation down to a few Hz. Common mode rejection was balanced to better than 10 000 for homogeneous fields and better than 200 for gradient fields with second-order compensation.

  17. Proof-of-principle demonstration of measurement-device-independent quantum key distribution using polarization qubits

    NASA Astrophysics Data System (ADS)

    Ferreira da Silva, T.; Vitoreti, D.; Xavier, G. B.; do Amaral, G. C.; Temporão, G. P.; von der Weid, J. P.

    2013-11-01

    We perform a proof-of-principle demonstration of the measurement-device-independent quantum key distribution protocol using weak coherent states and polarization-encoded qubits over two optical fiber links of 8.5 km each. Each link was independently stabilized against polarization drifts using a full-polarization control system employing two wavelength-multiplexed control channels. A linear-optics-based polarization Bell-state analyzer was built into the intermediate station, Charlie, which is connected to both Alice and Bob via the optical fiber links. Using decoy states, a lower bound for the secret-key generation rate of 1.04×10-6 bits/pulse is computed.

  18. Measurement-device-independent quantum key distribution with a passive decoy-state method

    NASA Astrophysics Data System (ADS)

    Shan, Yu-Zhu; Sun, Shi-Hai; Ma, Xiang-Chun; Jiang, Mu-Sheng; Zhou, Yan-Li; Liang, Lin-Mei

    2014-10-01

    Measurement-device-independent quantum key distribution (MDI-QKD) can remove all detector loopholes. When it is combined with the decoy-state method, the final key is unconditionally secure, even if Alice and Bob do not have strict single-photon sources. However, active modulation of source intensity, which is used to generate the decoy state, may leave side channels and leak additional information to Eve. In this paper, we consider the MDI-QKD with a passive decoy state, in which both Alice and Bob send pulses to an untrusted third party, Charlie. Then, in order to estimate the key generation rate, we derive two tight formulas to estimate the lower bound of the yield and the upper bound of the error rate that both Alice and Bob send a single-photon pulse to Charlie. Furthermore, the statistical fluctuation due to the finite length of data is also taken into account based on the standard statistical analysis.

  19. Wavelength tuning of InAs quantum dot laser by micromirror device

    NASA Astrophysics Data System (ADS)

    Yan, J. Y.; Gong, Q.; Kang, C. Z.; Xu, H. X.; Cao, C. F.; Li, Y. Y.; Wang, S. M.; Wang, H. L.

    2015-09-01

    We report on the InAs quantum dot (QD) external cavity laser (ECL) using a digital mirror device (DMD) as the key component for wavelength tuning. The InAs QD laser diode was grown by gas source molecular-beam epitaxy, which had a broad gain profile. Single mode operation was achieved with the side mode suppression ratio of 21 dB when the optical feedback was provided by a mirror pattern consisting of 9 micromirrors. Moreover, two-color lasing was demonstrated with two laser lines having frequency difference in the THz range. The incorporation of DMD in the ECL enables great flexibility and many unique features, such as high tuning speed independent of the tuning step, two-color or multi-color lasing, and adjustable intensity for individual laser lines.

  20. Quantum control and a novel atom-light quantum interface

    NASA Astrophysics Data System (ADS)

    Jessen, Poul S.; Anderson, Brian E.; Montano, Enrique; Hemmer, Daniel; Sosa Martinez, Hector; Smith, Aaron

    2014-09-01

    The emerging field of quantum engineering seeks to design and construct quantum devices for use in technological applications. To do so, one must learn to prepare a physical system in a well defined quantum state, drive it though a specified evolution, and access its final state through measurement. Historically, some of the most successful laboratory platforms with which to explore these challenges have originated in the field of quantum optics. This work reviews some of the recent advances in single- and many atom quantum control at the College of Optical Science, and their integration into a novel atom-light quantum interface.

  1. Quantum tricks with femtosecond light pulses teach magnetic devices to think ultrafast

    NASA Astrophysics Data System (ADS)

    Perakis, I. E.; Lingos, P. C.; Wang, J.

    2014-03-01

    The technological demand to push the gigahertz switching speed limit of today's magnetic memory/logic devices into the terahertz (1THz=1ps-1) regime underlies the entire field of spin-electronics and integrated multi- functional devices. This challenge is met by all-optical magnetic switching based on coherent spin manipulation By analogy to femto-chemistry and photosynthetic dynamics where photo-products of chemical/biochemical re- actions can be influenced by creating suitable superpositions of molecular states, femtosecond (fs) laser-excited coherence between spin/orbital/charge states can switch magnetic orders, by "suddenly" breaking the delicate balance between competing phases of correlated materials, e.g., the colossal magneto-resistive (CMR) manganites suitable for applications. Here we discuss femtosecond (fs) all-optical switching from antiferro- to ferromagnetic ordering via establishment of a magnetization increase within ˜100 fs, while the laser field still interacts with the system. Such non-equilibrium ferromagnetic correlations arise from quantum spin-flip fluctuations corre- lated with coherent superpositions of electronic states. The development of ferromagnetic correlations during the fs laser pulse reveals an initial quantum coherent regime of magnetism, clearly distinguished from the pi- cosecond lattice-heating regime characterized by phase separation. We summarize a microscopic theory based on density matrix equations of motion for composite fermion Hubbard operators, instead of bare electrons, that take into account the strong spin and charge local correlations. Our work merges two fields, femto-magnetism in metals/band insulators and non-equilibrium phase transitions of strongly correlated electrons, where local interactions exceeding the kinetic energy produce a complex balance of competing orders.

  2. Novel non-local effects in three-terminal hybrid devices with quantum dot

    PubMed Central

    Michałek, G.; Domański, T.; Bułka, B.R.; Wysokiński, K.I.

    2015-01-01

    We predict non-local effect in the three-terminal hybrid device consisting of the quantum dot (QD) tunnel coupled to two normal and one superconducting reservoirs. It manifests itself as the negative non-local resistance and results from the competition between the ballistic electron transfer (ET) and the crossed Andreev scattering (CAR). The effect is robust both in the linear and non-linear regimes. In the latter case the screening of charges and the long-range interactions play significant role. We show that sign change of the non-local conductance depends on the subgap Shiba/Andreev states, and it takes place even in absence of the Coulomb interactions. The effect is large and can be experimentally verified using the four probe setup. Since the induced non-local voltage changes sign and magnitude upon varying the gate potential and/or coupling of the quantum dot to the superconducting lead, such measurement could hence provide a controlled and precise method to determine the positions of the Shiba/Andreev states. Our predictions ought to be contrasted with non-local effects observed hitherto in the three-terminal planar junctions where the residual negative non-local conductance has been observed at large voltages, related to the Thouless energy of quasiparticles tunneling through the superconducting slab. PMID:26415683

  3. Novel non-local effects in three-terminal hybrid devices with quantum dot

    NASA Astrophysics Data System (ADS)

    Michałek, G.; Domański, T.; Bułka, B. R.; Wysokiński, K. I.

    2015-09-01

    We predict non-local effect in the three-terminal hybrid device consisting of the quantum dot (QD) tunnel coupled to two normal and one superconducting reservoirs. It manifests itself as the negative non-local resistance and results from the competition between the ballistic electron transfer (ET) and the crossed Andreev scattering (CAR). The effect is robust both in the linear and non-linear regimes. In the latter case the screening of charges and the long-range interactions play significant role. We show that sign change of the non-local conductance depends on the subgap Shiba/Andreev states, and it takes place even in absence of the Coulomb interactions. The effect is large and can be experimentally verified using the four probe setup. Since the induced non-local voltage changes sign and magnitude upon varying the gate potential and/or coupling of the quantum dot to the superconducting lead, such measurement could hence provide a controlled and precise method to determine the positions of the Shiba/Andreev states. Our predictions ought to be contrasted with non-local effects observed hitherto in the three-terminal planar junctions where the residual negative non-local conductance has been observed at large voltages, related to the Thouless energy of quasiparticles tunneling through the superconducting slab.

  4. In vitro retention of a new thermoplastic titratable mandibular advancement device

    PubMed Central

    Braem, Marc

    2015-01-01

    Oral appliance (OA) therapy with a mandibular advancement device (OAm) is a non-invasive, alternative approach to maintaining upper airway patency. The main requirement for an OAm to be effective is the adequate retention on the teeth while the patient is asleep. We evaluated the retentive forces of a new low-cost, customizable, titratable, thermoplastic OAm (BluePro ®; BlueSom, France). Dental impressions and casts were made for one patient with complete upper and lower dental arches including the third molars and class II bite proportions. A setup based on Frasaco ANA-4 models was also used. Two protrusive positions of the mandible were investigated: 3 mm and 8 mm, representing respectively 25% and 65% of the maximal protrusion. The forces required to remove the BluePro ® device from the carriers were recorded continuously over 730 cycles (=365 days, twice a day) to simulate 1 year of clinical use. At 8 mm protrusion the BluePro ® device showed retentive forces of ~27N. There was a slight but non-significant decrease in retentive forces in the tests on the epoxified carriers which was not found on the ANA-4 carriers. There were no significant differences between the carriers as a function of protrusion. The BluePro ® device tested in the present study possesses sufficient retention forces to resist initial jaw opening forces and full mouth opening forces estimated to be ~20N. It could therefore broaden the indications for use of thermoplastic OAms. It could provide a temporary OAm while a custom-made OAm is being manufactured or repaired. Patients could be provided with a low-cost try-out device capable of reliable titration, providing an indication of effectiveness and of patient acceptance of an OAm, although the effect of device shape and size on therapeutic outcome is not yet known. Finally it could provide an affordable OAm solution in resource-restricted healthcare settings. PMID:25901281

  5. Turnbuckle diamond anvil cell for high-pressure measurements in a superconducting quantum interference device magnetometer.

    PubMed

    Giriat, Gaétan; Wang, Weiwei; Attfield, J Paul; Huxley, Andrew D; Kamenev, Konstantin V

    2010-07-01

    We have developed a miniature diamond anvil cell for magnetization measurements in a widely used magnetic property measurement system commercial magnetometer built around a superconducting quantum interference device. The design of the pressure cell is based on the turnbuckle principle in which force can be created and maintained by rotating the body of the device while restricting the counterthreaded end-nuts to translational movement. The load on the opposed diamond anvils and the sample between them is generated using a hydraulic press. The load is then locked by rotating the body of the cell with respect to the end-nuts. The dimensions of the pressure cell have been optimized by use of finite element analysis. The cell is approximately a cylinder 7 mm long and 7 mm in diameter and weighs only 1.5 g. Due to its small size the cell thermalizes rapidly. It is capable of achieving pressures in excess of 10 GPa while allowing measurements to be performed with the maximum sensitivity of the magnetometer. The performance of the pressure cell is illustrated by a high pressure magnetic study of Mn(3)[Cr(CN)(6)](2) x xH(2)O Prussian blue analog up to 10.3 GPa. PMID:20687740

  6. Turnbuckle diamond anvil cell for high-pressure measurements in a superconducting quantum interference device magnetometer

    NASA Astrophysics Data System (ADS)

    Giriat, Gaétan; Wang, Weiwei; Attfield, J. Paul; Huxley, Andrew D.; Kamenev, Konstantin V.

    2010-07-01

    We have developed a miniature diamond anvil cell for magnetization measurements in a widely used magnetic property measurement system commercial magnetometer built around a superconducting quantum interference device. The design of the pressure cell is based on the turnbuckle principle in which force can be created and maintained by rotating the body of the device while restricting the counterthreaded end-nuts to translational movement. The load on the opposed diamond anvils and the sample between them is generated using a hydraulic press. The load is then locked by rotating the body of the cell with respect to the end-nuts. The dimensions of the pressure cell have been optimized by use of finite element analysis. The cell is approximately a cylinder 7 mm long and 7 mm in diameter and weighs only 1.5 g. Due to its small size the cell thermalizes rapidly. It is capable of achieving pressures in excess of 10 GPa while allowing measurements to be performed with the maximum sensitivity of the magnetometer. The performance of the pressure cell is illustrated by a high pressure magnetic study of Mn3[Cr(CN)6]2ṡxH2O Prussian blue analog up to 10.3 GPa.

  7. Nitride based quantum well light-emitting devices having improved current injection efficiency

    SciTech Connect

    Tansu, Nelson; Zhao, Hongping; Liu, Guangyu; Arif, Ronald

    2014-12-09

    A III-nitride based device provides improved current injection efficiency by reducing thermionic carrier escape at high current density. The device includes a quantum well active layer and a pair of multi-layer barrier layers arranged symmetrically about the active layer. Each multi-layer barrier layer includes an inner layer abutting the active layer; and an outer layer abutting the inner layer. The inner barrier layer has a bandgap greater than that of the outer barrier layer. Both the inner and the outer barrier layer have bandgaps greater than that of the active layer. InGaN may be employed in the active layer, AlInN, AlInGaN or AlGaN may be employed in the inner barrier layer, and GaN may be employed in the outer barrier layer. Preferably, the inner layer is thin relative to the other layers. In one embodiment the inner barrier and active layers are 15 .ANG. and 24 .ANG. thick, respectively.

  8. Detector-device-independent quantum key distribution: Security analysis and fast implementation

    NASA Astrophysics Data System (ADS)

    Boaron, Alberto; Korzh, Boris; Houlmann, Raphael; Boso, Gianluca; Lim, Charles Ci Wen; Martin, Anthony; Zbinden, Hugo

    2016-08-01

    One of the most pressing issues in quantum key distribution (QKD) is the problem of detector side-channel attacks. To overcome this problem, researchers proposed an elegant "time-reversal" QKD protocol called measurement-device-independent QKD (MDI-QKD), which is based on time-reversed entanglement swapping. However, MDI-QKD is more challenging to implement than standard point-to-point QKD. Recently, an intermediary QKD protocol called detector-device-independent QKD (DDI-QKD) has been proposed to overcome the drawbacks of MDI-QKD, with the hope that it would eventually lead to a more efficient detector side-channel-free QKD system. Here, we analyze the security of DDI-QKD and elucidate its security assumptions. We find that DDI-QKD is not equivalent to MDI-QKD, but its security can be demonstrated with reasonable assumptions. On the more practical side, we consider the feasibility of DDI-QKD and present a fast experimental demonstration (clocked at 625 MHz), capable of secret key exchange up to more than 90 km.

  9. Development of a Cryostat to Characterize Nano-scale Superconducting Quantum Interference Devices

    NASA Astrophysics Data System (ADS)

    Longo, Mathew; Matheny, Matthew; Knudsen, Jasmine

    2016-03-01

    We have designed and constructed a low-noise vacuum cryostat to be used for the characterization of nano-scale superconducting quantum interference devices (SQUIDs). Such devices are very sensitive to magnetic fields and can measure changes in flux on the order of a single electron magnetic moment. As a part of the design process, we calculated the separation required between the cryogenic preamplifier and superconducting magnet, including a high-permeability magnetic shield, using a finite-element model of the apparatus. The cryostat comprises a vacuum cross at room temperature for filtered DC and shielded RF electrical connections, a thin-wall stainless steel support tube, a taper-sealed cryogenic vacuum can, and internal mechanical support and wiring for the nanoSQUID. The Dewar is modified with a room-temperature flange with a sliding seal for the cryostat. The flange supports the superconducting 3 Tesla magnet and thermometry wiring. Upon completion of the cryostat fabrication and Dewar modifications, operation of the nanoSQUIDs as transported from our collaborator's laboratory in Israel will be confirmed, as the lead forming the SQUID is sensitive to oxidation and the SQUIDs must be shipped in a vacuum container. After operation of the nanoSQUIDs is confirmed, the primary work of characterizing their high-speed properties will begin. This will include looking at the measurement of relaxation oscillations at high bandwidth in comparison to the theoretical predictions of the current model.

  10. Further measurements of bremsstrahlung from the insertion device beamlines of the Advanced Photon Source.

    SciTech Connect

    Job, P. K.

    1998-09-16

    Bremsstrahlung is produced in the Advanced Photon Source (APS) storage ring when the positron beam interacts with the storage-ring components or with the residual gas molecules in the storage-ring vacuum. The interaction of the positrons with the gas molecules occurs continually during storage ring operation. Bremsstrahlung is important at the insertion device straight sections because the contribution from each interaction adds up to produce a narrow mono-directional beam that travel down the beamlines. At the APS, with long storage ring beam straight paths (15.38 meters), gas bremsstrahlung in the insertion device beamlines can be significant. The preliminary results of the bremsstrahlung measurements in the insertion device beamlines of the APS was presented at SATIF3. This paper presents the results of further measurements at the two insertion device (ID) beamlines with higher statistics in the data collection. The beam current and the vacuum normalized bremsstrahlung power is fairly constant in a beamline for a given storage ring fill pattern, but may vary from beamline to beamline. The average bremsstrahlung power is measured as 118 {+-} 9 GeV/s/nT/mA at beamline 11 ID and as 36 {+-} 2 GeV/s/nT/mA at beamline 6 ID. These results, along with the results from the four previous independent bremsstrahlung measurements, enabled us to conclude upon the various reasons causing this variation.

  11. Advanced simulation technology for etching process design for CMOS device applications

    NASA Astrophysics Data System (ADS)

    Kuboi, Nobuyuki; Fukasawa, Masanaga; Tatsumi, Tetsuya

    2016-07-01

    Plasma etching is a critical process for the realization of high performance in the next generation of CMOS devices. To predict and control fluctuations in the etching properties accurately during mass production, it is essential that etching process simulation technology considers fluctuations in the plasma chamber wall conditions, the effects of by-products on the critical dimensions, the Si recess dependence on the wafer open area ratio and local pattern structure, and the time-dependent plasma-induced damage distribution associated with the three-dimensional feature scale profile at the 100 nm level. This consideration can overcome the issues with conventional simulations performed under the assumed ideal conditions, which are not accurate enough for practical process design. In this article, these advanced process simulation technologies are reviewed, and, from the results of suitable process simulations, a new etching system that automatically controls the etching properties is proposed to enable stable CMOS device fabrication with high yields.

  12. Left ventricular assist device driveline infections: recent advances and future goals

    PubMed Central

    2015-01-01

    Left ventricular assist devices (LVADs) have revolutionized the treatment of advanced heart failure, but infection remains a substantial risk. LVAD driveline infections (DLIs) are the most common type of LVAD-associated infection (LVADI). In the past several years we have expanded our understanding of DLI epidemiology, standardized the definition of LVADIs, improved infection rates through changes in implantation techniques, and investigated potential new modalities for DLI diagnosis. However, significant challenges remain for optimizing DLI prevention and treatment. These challenges include standardizing and improving both empiric and targeted antimicrobial therapy, expanding our understanding of effective driveline exit site dressings and topical therapies, and defining the patient population that benefits from device exchange and transplant. Additionally, in an era of expanding antibiotic resistance we need to continue investigating novel, non-antibiotic therapies for prevention and treatment of DLIs. PMID:26793335

  13. Advances in phosphors based on organic materials for light emitting devices

    NASA Astrophysics Data System (ADS)

    Sharma, Kashma; Kumar, Vijay; Kumar, Vinod; Swart, Hendrik C.

    2016-01-01

    A brief overview is presented in the light emitting diodes (LEDs) based on purely organic materials. Organic LEDs are of great interest to the research community because of their outstanding properties and flexibility. Comparison between devices made using different organic materials and their derivatives with respect to synthetic protocols, characterizations, quantum efficiencies, sensitivity, specificity and their applications in various fields have been discussed. This review also discusses the essential requirement and scientific issues that arise in synthesizing cost-effective and environmental friendly organic LEDs diodes based on purely organic materials. This mini review aims to capture and convey some of the key current developments in phosphors formed by purely organic materials and highlights some possible future applications. Hence, this study comes up with a widespread discussion on the various contents in a single platform. Also, it offers avenues for new researchers for futuristic development in the area.

  14. Development of the Vibration Isolation System for the Advanced Resistive Exercise Device

    NASA Technical Reports Server (NTRS)

    Niebuhr, Jason H.; Hagen, Richard A.

    2011-01-01

    This paper describes the development of the Vibration Isolation System for the Advanced Resistive Exercise Device from conceptual design to lessons learned. Maintaining a micro-g environment on the International Space Station requires that experiment racks and major vibration sources be isolated. The challenge in characterizing exercise loads and testing the system in the presence of gravity led to a decision to qualify the system by analysis. Available data suggests that the system is successful in attenuating loads, yet there has been a major component failure and several procedural issues during its 3 years of operational use.

  15. Computational Models of Exercise on the Advanced Resistance Exercise Device (ARED)

    NASA Technical Reports Server (NTRS)

    Newby, Nate; Caldwell, Erin; Scott-Pandorf, Melissa; Peters,Brian; Fincke, Renita; DeWitt, John; Poutz-Snyder, Lori

    2011-01-01

    Muscle and bone loss remain a concern for crew returning from space flight. The advanced resistance exercise device (ARED) is used for on-orbit resistance exercise to help mitigate these losses. However, characterization of how the ARED loads the body in microgravity has yet to be determined. Computational models allow us to analyze ARED exercise in both 1G and 0G environments. To this end, biomechanical models of the squat, single-leg squat, and deadlift exercise on the ARED have been developed to further investigate bone and muscle forces resulting from the exercises.

  16. [Objective surgery -- advanced robotic devices and simulators used for surgical skill assessment].

    PubMed

    Suhánszki, Norbert; Haidegger, Tamás

    2014-12-01

    Robotic assistance became a leading trend in minimally invasive surgery, which is based on the global success of laparoscopic surgery. Manual laparoscopy requires advanced skills and capabilities, which is acquired through tedious learning procedure, while da Vinci type surgical systems offer intuitive control and advanced ergonomics. Nevertheless, in either case, the key issue is to be able to assess objectively the surgeons' skills and capabilities. Robotic devices offer radically new way to collect data during surgical procedures, opening the space for new ways of skill parameterization. This may be revolutionary in MIS training, given the new and objective surgical curriculum and examination methods. The article reviews currently developed skill assessment techniques for robotic surgery and simulators, thoroughly inspecting their validation procedure and utility. In the coming years, these methods will become the mainstream of Western surgical education. PMID:25500641

  17. GaAs metal-oxide-semiconductor based nonvolatile memory devices embedded with ZnO quantum dots

    NASA Astrophysics Data System (ADS)

    Kundu, Souvik; Rao Gollu, Sankara; Sharma, Ramakant; Halder, Nripendra. N.; Biswas, Pranab; Banerji, P.; Gupta, D.

    2013-08-01

    Ultrathin InP passivated GaAs non-volatile memory devices were fabricated with chemically synthesized 5 nm ZnO quantum dots embedded into ZrO2 high-k oxide matrix deposited through metal organic chemical vapor deposition. In these memory devices, the memory window was found to be 6.10 V and the obtained charge loss was only 15.20% after 105 s. The superior retention characteristics and a wide memory window are achieved due to presence of ZnO quantum dots between tunneling and control oxide layers. Room temperature Coulomb blockade effect was found in these devices and it was ascertained to be the main reason for low leakage. Electronic band diagram with program and erase operations were described on the basis of electrical characterizations.

  18. Optimized QKD BB84 protocol using quantum dense coding and CNOT gates: feasibility based on probabilistic optical devices

    NASA Astrophysics Data System (ADS)

    Gueddana, Amor; Attia, Moez; Chatta, Rihab

    2014-05-01

    In this work, we simulate a fiber-based Quantum Key Distribution Protocol (QKDP) BB84 working at the telecoms wavelength 1550 nm with taking into consideration an optimized attack strategy. We consider in our work a quantum channel composed by probabilistic Single Photon Source (SPS), single mode optical Fiber and quantum detector with high efficiency. We show the advantages of using the Quantum Dots (QD) embedded in micro-cavity compared to the Heralded Single Photon Sources (HSPS). Second, we show that Eve is always getting some information depending on the mean photon number per pulse of the used SPS and therefore, we propose an optimized version of the QKDP BB84 based on Quantum Dense Coding (QDC) that could be implemented by quantum CNOT gates. We evaluate the success probability of implementing the optimized QKDP BB84 when using nowadays probabilistic quantum optical devices for circuit realization. We use for our modeling an abstract probabilistic model of a CNOT gate based on linear optical components and having a success probability of sqrt (4/27), we take into consideration the best SPSs realizations, namely the QD and the HSPS, generating a single photon per pulse with a success probability of 0.73 and 0.37, respectively. We show that the protocol is totally secure against attacks but could be correctly implemented only with a success probability of few percent.

  19. Advanced boundary condition method in quantum transport and its application in nanodevices

    NASA Astrophysics Data System (ADS)

    He, Yu

    Modern semiconductor devices have reached critical dimensions in the sub-20nm range. During the last decade, quantum transport methods have become the standard approaches to model nanoscale devices. In quantum transport methods, Schrodinger equations are solved in the critical device channel with the contacts served as the open boundary conditions. Proper and efficient treatments of these boundary conditions are essential to provide accurate prediction of device performance. The open boundary conditions, which represent charge injection and extraction effects, are described by contact self-energies. All existing contact self-energy methods assume periodic and semiinfinite contacts, which are in stark contrast to realistic devices where the contacts often have complicated geometries or imperfections. On the other hand, confined structures such as quantum dots, nanowires, and ultra-thin bodies play an important role in nanodevice designs. In the tight binding models of these confined structures, the surfaces require appropriate boundary treatments to remove the dangling bonds. The existing boundary treatments fall into two categories. One is to explicitly include the passivation atoms in the device. This is limited to passivation with atoms and small molecules due to the increasing rank of the Hamiltonian. The other is to implicitly incorporate passivation by altering the orbital energies of the dangling bonds with a passivation potential. This method only works for certain crystal structures and symmetries, and fails to distinguish different passivation scenarios, such as hydrogen and oxygen passivation. In this work, an efficient self-energy method applicable for arbitrary contact structures is developed. This method is based on an iterative algorithm which considers the explicit contact segments. The method is demonstrated on a graphene nanoribbon structure with trumpet shape contacts and a Si0.5Ge0.5 nanowire transistor with alloy disorder contacts. Furthermore

  20. Intermediate-band photosensitive device with quantum dots having tunneling barrier embedded in organic matrix

    DOEpatents

    Forrest, Stephen R.

    2008-08-19

    A plurality of quantum dots each have a shell. The quantum dots are embedded in an organic matrix. At least the quantum dots and the organic matrix are photoconductive semiconductors. The shell of each quantum dot is arranged as a tunneling barrier to require a charge carrier (an electron or a hole) at a base of the tunneling barrier in the organic matrix to perform quantum mechanical tunneling to reach the respective quantum dot. A first quantum state in each quantum dot is between a lowest unoccupied molecular orbital (LUMO) and a highest occupied molecular orbital (HOMO) of the organic matrix. Wave functions of the first quantum state of the plurality of quantum dots may overlap to form an intermediate band.

  1. Integrated p–n junction InGaN/GaN multiple-quantum-well devices with diverse functionalities

    NASA Astrophysics Data System (ADS)

    Cai, Wei; Gao, Xumin; Yuan, Wei; Yang, Yongchao; Yuan, Jialei; Zhu, Hongbo; Wang, Yongjin

    2016-05-01

    We propose, fabricate, and demonstrate integrated p–n junction InGaN/GaN multiple-quantum-well devices with diverse functionalities on a GaN-on-silicon platform. Suspended devices with a common n-contact are realized using a wafer-level process. For the integrated devices, part of the light emitted by a light-emitting diode (LED) is guided in-plane through a suspended waveguide and is sensed by another photodiode. The induced photocurrent is tuned by the LED. The integrated devices can act as two independent LEDs to deliver different signals simultaneously for free-space visible light communication. Furthermore, the suspended devices can be used as two separate photodiodes to detect incident light with a distinct on/off switching performance.

  2. Simulation and Experimental Study on Anti-reflection Characteristics of Nano-patterned Si Structures for Si Quantum Dot-Based Light-Emitting Devices

    NASA Astrophysics Data System (ADS)

    Shao, Wenyi; Lu, Peng; Li, Wei; Xu, Jun; Xu, Ling; Chen, Kunji

    2016-06-01

    Surface-textured structure is currently an interesting topic since it can efficiently reduce the optical losses in advanced optoelectronic devices via light management. In this work, we built a model in finite-difference time-domain (FDTD) solutions by setting the simulation parameters based on the morphology of the Si nanostructures and compared with the experimental results in order to study the anti-reflection behaviors of the present nano-patterned structures. It is found that the reflectance is gradually reduced by increasing the depth of Si nanostructures which is in well agreement with the experimental observations. The reflectance can be lower than 10 % in the light range from 400 to 850 nm for Si nano-patterned structures with a depth of 150 nm despite the quite low aspect ratio, which can be understood as the formation of gradually changed index layer and the scattering effect of Si nano-patterned structures. By depositing the Si quantum dots/SiO2 multilayers on nano-patterned Si substrate, the reflectance can be further suppressed and the luminescence intensity centered at 820 nm from Si quantum dots is enhanced by 6.6-fold compared with that of flat one, which can be attributed to the improved light extraction efficiency. However, the further etch time causes the reduction of luminescence intensity from Si quantum dots which may ascribe to the serious surface recombination of carriers.

  3. Simulation and Experimental Study on Anti-reflection Characteristics of Nano-patterned Si Structures for Si Quantum Dot-Based Light-Emitting Devices.

    PubMed

    Shao, Wenyi; Lu, Peng; Li, Wei; Xu, Jun; Xu, Ling; Chen, Kunji

    2016-12-01

    Surface-textured structure is currently an interesting topic since it can efficiently reduce the optical losses in advanced optoelectronic devices via light management. In this work, we built a model in finite-difference time-domain (FDTD) solutions by setting the simulation parameters based on the morphology of the Si nanostructures and compared with the experimental results in order to study the anti-reflection behaviors of the present nano-patterned structures. It is found that the reflectance is gradually reduced by increasing the depth of Si nanostructures which is in well agreement with the experimental observations. The reflectance can be lower than 10 % in the light range from 400 to 850 nm for Si nano-patterned structures with a depth of 150 nm despite the quite low aspect ratio, which can be understood as the formation of gradually changed index layer and the scattering effect of Si nano-patterned structures. By depositing the Si quantum dots/SiO2 multilayers on nano-patterned Si substrate, the reflectance can be further suppressed and the luminescence intensity centered at 820 nm from Si quantum dots is enhanced by 6.6-fold compared with that of flat one, which can be attributed to the improved light extraction efficiency. However, the further etch time causes the reduction of luminescence intensity from Si quantum dots which may ascribe to the serious surface recombination of carriers. PMID:27356564

  4. Stress-induced Effects Caused by 3D IC TSV Packaging in Advanced Semiconductor Device Performance

    SciTech Connect

    Sukharev, V.; Kteyan, A.; Choy, J.-H.; Hovsepyan, H.; Markosian, A.; Zschech, E.; Huebner, R.

    2011-11-10

    Potential challenges with managing mechanical stress and the consequent effects on device performance for advanced 3D through-silicon-via (TSV) based technologies are outlined. The paper addresses the growing need in a simulation-based design verification flow capable to analyze a design of 3D IC stacks and to determine across-die out-of-spec variations in device electrical characteristics caused by the layout and through-silicon-via (TSV)/package-induced mechanical stress. The limited characterization/measurement capabilities for 3D IC stacks and a strict ''good die'' requirement make this type of analysis critical for the achievement of an acceptable level of functional and parametric yield and reliability. The paper focuses on the development of a design-for-manufacturability (DFM) type of methodology for managing mechanical stresses during a sequence of designs of 3D TSV-based dies, stacks and packages. A set of physics-based compact models for a multi-scale simulation to assess the mechanical stress across the device layers in silicon chips stacked and packaged with the 3D TSV technology is proposed. A calibration technique based on fitting to measured stress components and electrical characteristics of the test-chip devices is presented. A strategy for generation of a simulation feeding data and respective materials characterization approach are proposed, with the goal to generate a database for multi-scale material parameters of wafer-level and package-level structures. For model validation, high-resolution strain measurements in Si channels of the test-chip devices are needed. At the nanoscale, the transmission electron microscopy (TEM) is the only technique available for sub-10 nm strain measurements so far.

  5. Green route synthesis of high quality CdSe quantum dots for applications in light emitting devices

    SciTech Connect

    Bera, Susnata; Singh, Shashi B.; Ray, S.K.

    2012-05-15

    Investigation was made on light emitting diodes fabricated using CdSe quantum dots. CdSe quantum dots were synthesized chemically using olive oil as the capping agent, instead of toxic phosphine. Room temperature photoluminescence investigation showed sharp 1st excitonic emission peak at 568 nm. Bi-layer organic/inorganic (P3HT/CdSe) hybrid light emitting devices were fabricated by solution process. The electroluminescence study showed low turn on voltage ({approx}2.2 V) .The EL peak intensity was found to increase by increasing the operating current. - Graphical abstract: Light emitting diode was fabricated using CdSe quantum dots using olive oil as the capping agent, instead of toxic phosphine. Bi-layer organic/inorganic (P3HT/CdSe) hybrid light emitting device shows strong electroluminescence in the range 630-661 nm. Highlights: Black-Right-Pointing-Pointer CdSe Quantum dots were synthesized using olive oil as the capping agent. Black-Right-Pointing-Pointer Light emitting device was fabricated using CdSe QDs/P3HT polymer heterojunction. Black-Right-Pointing-Pointer The I-V characteristics study showed low turn on voltage at {approx}2.2 V. Black-Right-Pointing-Pointer The EL peak intensity increases with increasing the operating current.

  6. Patterned mist deposition of tri-colour CdSe/ZnS quantum dot films toward RGB LED devices

    NASA Astrophysics Data System (ADS)

    Pickering, S.; Kshirsagar, A.; Ruzyllo, J.; Xu, J.

    2012-06-01

    In this experiment a technique of mist deposition was explored as a way to form patterned ultra-thin-films of CdSe/ZnS core/shell nanocrystalline quantum dots using colloidal solutions. The objective of this study was to investigate the feasibility of mist deposition as a patterning method for creating multicolour quantum dot light emitting diodes. Mist deposition was used to create three rows of quantum dot light emitting diodes on a single device with each row having a separate colour. The colours chosen were red, green and yellow with corresponding peak wavelengths of 620 nm, 558 nm, and 587 nm. The results obtained from this experiment show that it is possible to create multicolour devices on a single substrate. The peak brightnesses obtained in this experiment for the red, green, and yellow were 508 cd/m, 507 cd/m, and 665 cd/m, respectively. The similar LED brightness is important in display technologies using colloidal quantum dots in a precursor solution to ensure one colour does not dominate the emitted spectrum. Results obtained in-terms of brightness were superior to those achieved with inkjet deposition. This study has shown that mist deposition is a viable method for patterned deposition applied to quantum dot light emitting diode display technologies.

  7. Recent advances in computational methodology for simulation of mechanical circulatory assist devices

    PubMed Central

    Marsden, Alison L.; Bazilevs, Yuri; Long, Christopher C.; Behr, Marek

    2014-01-01

    Ventricular assist devices (VADs) provide mechanical circulatory support to offload the work of one or both ventricles during heart failure. They are used in the clinical setting as destination therapy, as bridge to transplant, or more recently as bridge to recovery to allow for myocardial remodeling. Recent developments in computational simulation allow for detailed assessment of VAD hemodynamics for device design and optimization for both children and adults. Here, we provide a focused review of the recent literature on finite element methods and optimization for VAD simulations. As VAD designs typically fall into two categories, pulsatile and continuous flow devices, we separately address computational challenges of both types of designs, and the interaction with the circulatory system with three representative case studies. In particular, we focus on recent advancements in finite element methodology that has increased the fidelity of VAD simulations. We outline key challenges, which extend to the incorporation of biological response such as thrombosis and hemolysis, as well as shape optimization methods and challenges in computational methodology. PMID:24449607

  8. Advanced Multi-Junction Photovoltaic Device Optimization For High Temperature Space Applications

    NASA Astrophysics Data System (ADS)

    Sherif, Michael

    2011-10-01

    Almost all solar cells available today for space or terrestrial applications are optimized for low temperature or "room temperature" operations, where cell performances demonstrate favourable efficiency figures. The fact is in many space applications, as well as when using solar concentrators, operating cell temperature are typically highly elevated, where cells outputs are severely depreciated. In this paper, a novel approach for the optimization of multi-junction photovoltaic devices at such high expected operating temperature is presented. The device optimization is carried out on the novel cell physical model previously developed at the Naval Postgraduate School using the SILVACO software tools [1]. Taking into account the high cost of research and experimentation involved with the development of advanced cells, this successful modelling technique was introduced and detailed results were previously presented by the author [2]. The flexibility of the proposed methodology is demonstrated and example results are shown throughout the whole process. The research demonstrated the capability of developing a realistic model of any type of solar cell, as well as thermo-photovoltaic devices. Details of an example model of an InGaP/GaAs/Ge multi-junction cell was prepared and fully simulated. The major stages of the process are explained and the simulation results are compared to published experimental data. An example of cell parameters optimization for high operating temperature is also presented. Individual junction layer optimization was accomplished through the use of a genetic search algorithm implemented in Matlab.

  9. Mechanism Development, Testing, and Lessons Learned for the Advanced Resistive Exercise Device

    NASA Technical Reports Server (NTRS)

    Lamoreaux, Christopher D.; Landeck, Mark E.

    2006-01-01

    The Advanced Resistive Exercise Device (ARED) has been developed at NASA Johnson Space Center, for the International Space Station (ISS) program. ARED is a multi-exercise, high-load resistive exercise device, designed for long duration, human space missions. ARED will enable astronauts to effectively maintain their muscle strength and bone mass in the micro-gravity environment more effectively than any other existing devices. ARED's resistance is provided via two, 20.3 cm (8 in) diameter vacuum cylinders, which provide a nearly constant resistance source. ARED also has a means to simulate the inertia that is felt during a 1-G exercise routine via the flywheel subassembly, which is directly tied to the motion of the ARED cylinders. ARED is scheduled to fly on flight ULF 2 to the ISS and will be located in Node 1. Presently, ARED is in the middle of its qualification and acceptance test program. An extensive testing program and engineering evaluation has increased the reliability of ARED by bringing potential design issues to light before flight production. Some of those design issues, resolutions, and design details will be discussed in this paper.

  10. The statistical fluctuation analysis for the measurement-device-independent quantum key distribution with heralded single-photon sources

    NASA Astrophysics Data System (ADS)

    Zhou, Xing-Yu; Zhang, Chun-Hui; Guo, Guang-Can; Wang, Qin

    2016-06-01

    In this paper, we carry out statistical fluctuation analysis for the new proposed measurement-device-independent quantum key distribution with heralded single-photon sources and further compare its performance with the mostly often used light sources, i.e., the weak coherent source. Due to a significantly lower probability for events with two photons present on the same side of the beam splitter in former than in latter, it gives drastically reduced quantum bit error rate in the X basis and can thus show splendid behavior in real-life implementations even when taking statistical fluctuations into account.

  11. Green route synthesis of high quality CdSe quantum dots for applications in light emitting devices

    NASA Astrophysics Data System (ADS)

    Bera, Susnata; Singh, Shashi B.; Ray, S. K.

    2012-05-01

    Investigation was made on light emitting diodes fabricated using CdSe quantum dots. CdSe quantum dots were synthesized chemically using olive oil as the capping agent, instead of toxic phosphine. Room temperature photoluminescence investigation showed sharp 1st excitonic emission peak at 568 nm. Bi-layer organic/inorganic (P3HT/CdSe) hybrid light emitting devices were fabricated by solution process. The electroluminescence study showed low turn on voltage (˜2.2 V) .The EL peak intensity was found to increase by increasing the operating current.

  12. Certifying the dimension of classical and quantum systems in a prepare-and-measure scenario with independent devices.

    PubMed

    Bowles, Joseph; Quintino, Marco Túlio; Brunner, Nicolas

    2014-04-11

    We consider the problem of testing the dimension of uncharacterized classical and quantum systems in a prepare-and-measure setup. Here we assume the preparation and measurement devices to be independent, thereby making the problem nonconvex. We present a simple method for generating nonlinear dimension witnesses for systems of arbitrary dimension. The simplest of our witnesses is highly robust to technical imperfections, and can certify the use of qubits in the presence of arbitrary noise and arbitrarily low detection efficiency. Finally, we show that this witness can be used to certify the presence of randomness, suggesting applications in quantum information processing. PMID:24765929

  13. Electronic and excitonic processes in light-emitting devices based on organic materials and colloidal quantum dots

    NASA Astrophysics Data System (ADS)

    Anikeeva, P. O.; Madigan, C. F.; Halpert, J. E.; Bawendi, M. G.; Bulović, V.

    2008-08-01

    We investigate the mechanism of operation of hybrid organic/colloidal quantum dot light emitting devices (QD-LEDs). Novel quantum dot (QD) deposition methods allow us to change the location of an emissive QD monolayer within a QD-LED multilayer structure. We find that the quantum efficiency of devices improves by >50% upon imbedding QD monolayers into the hole transporting layer <10nm away from the interface between hole and electron transporting layers. We consider two possible mechanisms responsible for this improvement: one based on a charge injection model of the device operation and the other based on an exciton energy-transfer model. In order to differentiate between the two suggested mechanisms, we fabricate a set of structures that enable control over charge injection into colloidal QDs. We find that the dominant process limiting QD-LED efficiency is charging of the QDs by trapped electrons. We demonstrate that with the set of organic materials implemented in this study, device efficiency is increased by maximizing energy transfer from organics to QDs and by limiting direct charge injection that contributes to QD charging.

  14. White organic light-emitting devices with CdSe/ZnS quantum dots as a red emitter

    NASA Astrophysics Data System (ADS)

    Li, Yanqin; Rizzo, Aurora; Mazzeo, Marco; Carbone, Luigi; Manna, Liberato; Cingolani, Roberto; Gigli, Giuseppe

    2005-06-01

    White hybrid organic/inorganic light-emitting devices (LEDs) have been fabricated by using stable red-emitting CdSe/ZnS core-shell quantum dots (QDs) covered with a trioctylphosphine oxide organic ligand. The device-active structure consists in a host/guest system with a blue-emitting poly[(9,9-dihexyloxyfluoren-2,7-diyl)-alt-co-(2-methoxy-5-{2-ethylhexyloxy}phenylen-1,4-diyl)] (PFH-MEH) polymer doped with red-emitting QDs and a green emitting metal chelate complex Alq3, with improved electron injection and transfer properties. A fairly pure white OLED with Commission Internationale de l'Eclairage coordinates of (0.30,0.33) is fabricated by accurate control of the Förster energy and charge-transfer mechanisms between the different device constituents obtained by tuning the concentration ratio of the QDs/PFH-MEH blend. In particular, charge-transfer processes to CdSe/ZnS core-shell quantum dots are found to be the key element for well-balanced white emission. Maximum external quantum efficiency up to 0.24% at 1mAcm-2 and 11 V in air atmosphere are reported, showing that hybrid LEDs can be a promising route towards more stable and efficient light-emitting devices for lighting applications.

  15. Low-noise nano superconducting quantum interference device operating in Tesla magnetic fields.

    PubMed

    Schwarz, Tobias; Nagel, Joachim; Wölbing, Roman; Kemmler, Matthias; Kleiner, Reinhold; Koelle, Dieter

    2013-01-22

    Superconductivity in the cuprate YBa(2)Cu(3)O(7) (YBCO) persists up to huge magnetic fields (B) up to several tens of Teslas, and sensitive direct current (dc) superconducting quantum interference devices (SQUIDs) can be realized in epitaxially grown YBCO films by using grain boundary Josephson junctions (GBJs). Here we present the realization of high-quality YBCO nanoSQUIDs, patterned by focused ion beam milling. We demonstrate low-noise performance of such a SQUID up to B = 1 T applied parallel to the plane of the SQUID loop at the temperature T = 4.2 K. The GBJs are shunted by a thin Au layer to provide nonhysteretic current voltage characteristics, and the SQUID incorporates a 90 nm wide constriction which is used for on-chip modulation of the magnetic flux through the SQUID loop. The white flux noise of the device increases only slightly from 1.3 μΦ(0)/(Hz)(1/2) at B = 0 to 2.3 μΦ(0)/(Hz))(1/2) at 1 T. Assuming that a point-like magnetic particle with magnetization in the plane of the SQUID loop is placed directly on top of the constriction and taking into account the geometry of the SQUID, we calculate a spin sensitivity S(μ)(1/2) = 62 μ(B)/(Hz))(1/2) at B = 0 and 110 μ(B)/(Hz))(1/2) at 1 T. The demonstration of low noise of such a SQUID in Tesla fields is a decisive step toward utilizing the full potential of ultrasensitive nanoSQUIDs for direct measurements of magnetic hysteresis curves of magnetic nanoparticles and molecular magnets. PMID:23252846

  16. Combination of a Sample Pretreatment Microfluidic Device with a Photoluminescent Graphene Oxide Quantum Dot Sensor for Trace Lead Detection.

    PubMed

    Park, Minsu; Ha, Hyun Dong; Kim, Yong Tae; Jung, Jae Hwan; Kim, Shin-Hyun; Kim, Do Hyun; Seo, Tae Seok

    2015-11-01

    A novel trace lead ion (Pb(2+)) detection platform by combining a microfluidic sample pretreatment device with a DNA aptamer linked photoluminescent graphene oxide quantum dot (GOQD) sensor was proposed. The multilayered microdevice included a microchamber which was packed with cation exchange resins for preconcentrating metal ions. The sample loading and recovery were automatically actuated by a peristaltic polydimethylsiloxane micropump with a flow rate of 84 μL/min. Effects of the micropump actuation time, metal ion concentration, pH, and the volumes of the sample and eluent on the metal ion capture and preconcentration efficiency were investigated on a chip. The Pb(2+) samples whose concentrations ranged from 0.48 nM to 1.2 μM were successfully recovered with a preconcentration factor value between 4 and 5. Then, the preconcentrated metal ions were quantitatively analyzed with a DNA aptamer modified GOQD. The DNA aptamer on the GOQD specifically captured the target Pb(2+) which can induce electron transfer from GOQD to Pb(2+) upon UV irradiation, thereby resulting in the fluorescence quenching of the GOQD. The disturbing effect of foreign anions on the Pb(2+) detection and the spiked Pb(2+) real samples were also analyzed. The proposed GOQD metal ion sensor exhibited highly sensitive Pb(2+) detection with a detection limit of 0.64 nM and a dynamic range from 1 to 1000 nM. The on-chip preconcentration of the trace metal ions from a large-volume sample followed by the metal ion detection by the fluorescent GOQD sensor can provide an advanced platform for on-site water pollution screening. PMID:26456631

  17. Implementation of continuous-variable quantum key distribution with composable and one-sided-device-independent security against coherent attacks

    PubMed Central

    Gehring, Tobias; Händchen, Vitus; Duhme, Jörg; Furrer, Fabian; Franz, Torsten; Pacher, Christoph; Werner, Reinhard F.; Schnabel, Roman

    2015-01-01

    Secret communication over public channels is one of the central pillars of a modern information society. Using quantum key distribution this is achieved without relying on the hardness of mathematical problems, which might be compromised by improved algorithms or by future quantum computers. State-of-the-art quantum key distribution requires composable security against coherent attacks for a finite number of distributed quantum states as well as robustness against implementation side channels. Here we present an implementation of continuous-variable quantum key distribution satisfying these requirements. Our implementation is based on the distribution of continuous-variable Einstein–Podolsky–Rosen entangled light. It is one-sided device independent, which means the security of the generated key is independent of any memoryfree attacks on the remote detector. Since continuous-variable encoding is compatible with conventional optical communication technology, our work is a step towards practical implementations of quantum key distribution with state-of-the-art security based solely on telecom components. PMID:26514280

  18. Implementation of continuous-variable quantum key distribution with composable and one-sided-device-independent security against coherent attacks.

    PubMed

    Gehring, Tobias; Händchen, Vitus; Duhme, Jörg; Furrer, Fabian; Franz, Torsten; Pacher, Christoph; Werner, Reinhard F; Schnabel, Roman

    2015-01-01

    Secret communication over public channels is one of the central pillars of a modern information society. Using quantum key distribution this is achieved without relying on the hardness of mathematical problems, which might be compromised by improved algorithms or by future quantum computers. State-of-the-art quantum key distribution requires composable security against coherent attacks for a finite number of distributed quantum states as well as robustness against implementation side channels. Here we present an implementation of continuous-variable quantum key distribution satisfying these requirements. Our implementation is based on the distribution of continuous-variable Einstein-Podolsky-Rosen entangled light. It is one-sided device independent, which means the security of the generated key is independent of any memoryfree attacks on the remote detector. Since continuous-variable encoding is compatible with conventional optical communication technology, our work is a step towards practical implementations of quantum key distribution with state-of-the-art security based solely on telecom components. PMID:26514280

  19. Implementation of continuous-variable quantum key distribution with composable and one-sided-device-independent security against coherent attacks

    NASA Astrophysics Data System (ADS)

    Gehring, Tobias; Händchen, Vitus; Duhme, Jörg; Furrer, Fabian; Franz, Torsten; Pacher, Christoph; Werner, Reinhard F.; Schnabel, Roman

    2015-10-01

    Secret communication over public channels is one of the central pillars of a modern information society. Using quantum key distribution this is achieved without relying on the hardness of mathematical problems, which might be compromised by improved algorithms or by future quantum computers. State-of-the-art quantum key distribution requires composable security against coherent attacks for a finite number of distributed quantum states as well as robustness against implementation side channels. Here we present an implementation of continuous-variable quantum key distribution satisfying these requirements. Our implementation is based on the distribution of continuous-variable Einstein-Podolsky-Rosen entangled light. It is one-sided device independent, which means the security of the generated key is independent of any memoryfree attacks on the remote detector. Since continuous-variable encoding is compatible with conventional optical communication technology, our work is a step towards practical implementations of quantum key distribution with state-of-the-art security based solely on telecom components.

  20. Development of a High Fidelity Dynamic Module of the Advanced Resistive Exercise Device (ARED) Using Adams

    NASA Technical Reports Server (NTRS)

    Humphreys, B. T.; Thompson, W. K.; Lewandowski, B. E.; Cadwell, E. E.; Newby, N. J.; Fincke, R. S.; Sheehan, C.; Mulugeta, L.

    2012-01-01

    NASA's Digital Astronaut Project (DAP) implements well-vetted computational models to predict and assess spaceflight health and performance risks, and enhance countermeasure development. DAP provides expertise and computation tools to its research customers for model development, integration, or analysis. DAP is currently supporting the NASA Exercise Physiology and Countermeasures (ExPC) project by integrating their biomechanical models of specific exercise movements with dynamic models of the devices on which the exercises were performed. This presentation focuses on the development of a high fidelity dynamic module of the Advanced Resistive Exercise Device (ARED) on board the ISS. The ARED module, illustrated in the figure below, was developed using the Adams (MSC Santa Ana, California) simulation package. The Adams package provides the capabilities to perform multi rigid body, flexible body, and mixed dynamic analyses of complex mechanisms. These capabilities were applied to accurately simulate: Inertial and mass properties of the device such as the vibration isolation system (VIS) effects and other ARED components, Non-linear joint friction effects, The gas law dynamics of the vacuum cylinders and VIS components using custom written differential state equations, The ARED flywheel dynamics, including torque limiting clutch. Design data from the JSC ARED Engineering team was utilized in developing the model. This included solid modeling geometry files, component/system specifications, engineering reports and available data sets. The Adams ARED module is importable into LifeMOD (Life Modeler, Inc., San Clemente, CA) for biomechanical analyses of different resistive exercises such as squat and dead-lift. Using motion capture data from ground test subjects, the ExPC developed biomechanical exercise models in LifeMOD. The Adams ARED device module was then integrated with the exercise subject model into one integrated dynamic model. This presentation will describe the

  1. Advances in methods and algorithms in a modern quantum chemistry program package.

    PubMed

    Shao, Yihan; Molnar, Laszlo Fusti; Jung, Yousung; Kussmann, Jörg; Ochsenfeld, Christian; Brown, Shawn T; Gilbert, Andrew T B; Slipchenko, Lyudmila V; Levchenko, Sergey V; O'Neill, Darragh P; DiStasio, Robert A; Lochan, Rohini C; Wang, Tao; Beran, Gregory J O; Besley, Nicholas A; Herbert, John M; Lin, Ching Yeh; Van Voorhis, Troy; Chien, Siu Hung; Sodt, Alex; Steele, Ryan P; Rassolov, Vitaly A; Maslen, Paul E; Korambath, Prakashan P; Adamson, Ross D; Austin, Brian; Baker, Jon; Byrd, Edward F C; Dachsel, Holger; Doerksen, Robert J; Dreuw, Andreas; Dunietz, Barry D; Dutoi, Anthony D; Furlani, Thomas R; Gwaltney, Steven R; Heyden, Andreas; Hirata, So; Hsu, Chao-Ping; Kedziora, Gary; Khalliulin, Rustam Z; Klunzinger, Phil; Lee, Aaron M; Lee, Michael S; Liang, Wanzhen; Lotan, Itay; Nair, Nikhil; Peters, Baron; Proynov, Emil I; Pieniazek, Piotr A; Rhee, Young Min; Ritchie, Jim; Rosta, Edina; Sherrill, C David; Simmonett, Andrew C; Subotnik, Joseph E; Woodcock, H Lee; Zhang, Weimin; Bell, Alexis T; Chakraborty, Arup K; Chipman, Daniel M; Keil, Frerich J; Warshel, Arieh; Hehre, Warren J; Schaefer, Henry F; Kong, Jing; Krylov, Anna I; Gill, Peter M W; Head-Gordon, Martin

    2006-07-21

    Advances in theory and algorithms for electronic structure calculations must be incorporated into program packages to enable them to become routinely used by the broader chemical community. This work reviews advances made over the past five years or so that constitute the major improvements contained in a new release of the Q-Chem quantum chemistry package, together with illustrative timings and applications. Specific developments discussed include fast methods for density functional theory calculations, linear scaling evaluation of energies, NMR chemical shifts and electric properties, fast auxiliary basis function methods for correlated energies and gradients, equation-of-motion coupled cluster methods for ground and excited states, geminal wavefunctions, embedding methods and techniques for exploring potential energy surfaces. PMID:16902710

  2. Quantum optics, cavity QED, and quantum optomechanics

    NASA Astrophysics Data System (ADS)

    Meystre, Pierre

    2013-05-01

    Quantum optomechanics provides a universal tool to achieve the quantum control of mechanical motion. It does that in devices spanning a vast range of parameters, with mechanical frequencies from a few Hertz to GHz, and with masses from 10-20 g to several kilos. Its underlying ideas can be traced back to the study of gravitational wave antennas, quantum optics, cavity QED and laser cooling which, when combined with the recent availability of advanced micromechanical and nanomechanical devices, opens a path to the realization of macroscopic mechanical systems that operate deep in the quantum regime. At the fundamental level this development paves the way to experiments that will lead to a more profound understanding of quantum mechanics; and from the point of view of applications, quantum optomechanical techniques will provide motion and force sensing near the fundamental limit imposed by quantum mechanics (quantum metrology) and significantly expand the toolbox of quantum information science. After a brief summary of key historical developments, the talk will give a broad overview of the current state of the art of quantum optomechanics, and comment on future prospects both in applied and in fundamental science. Work supported by NSF, ARO and the DARPA QuASAR and ORCHID programs.

  3. An experimental double relaxation oscillation superconducting quantum interference device with on-chip feedback

    NASA Astrophysics Data System (ADS)

    Podt, M.; Flokstra, J.; Rogalla, H.

    2004-04-01

    A wide-band double relaxation oscillation superconducting quantum interference device (DROS) with on-chip digital flux locked loop (FLL) circuitry, a Smart DROS, has been realized and experimentally investigated. The key element of the FLL circuitry is a superconducting up-down counter. In order to maximize the flux slew rate, the Smart DROS has been optimized with respect to the coupling between the DROS and the up-down counter, and the quantization unit of the feedback flux. For the Smart DROS with an inductance of 280 pH the flux quantization unit was 5 × 10-2 PHgr0. The experiments showed proper operation of the superconducting up-down counter. The full functionality of the complete Smart DROS in a closed loop was demonstrated. For operation at a clock frequency of 100 MHz, a maximum flux slew rate of 5 × 106 PHgr0 s-1 was calculated from the measured parameters. Numerical simulations showed that the Smart DROS allows a maximum flux slew rate up to 108 PHgr0 s-1 by reducing the area of the Josephson junctions.

  4. Practical decoy-state measurement-device-independent quantum key distribution

    NASA Astrophysics Data System (ADS)

    Sun, Shi-Hai; Gao, Ming; Li, Chun-Yan; Liang, Lin-Mei

    2013-05-01

    Measurement-device-independent quantum key distribution (MDI-QKD) is immune to all the detection attacks; thus when it is combined with the decoy-state method, the final key is unconditionally secure, even if a practical weak coherent source is used by Alice and Bob. However, until now, the analysis of decoy-state MDI-QKD with a weak coherent source is incomplete. In this paper, we derive, with only vacuum+weak decoy state, some tight formulas to estimate the lower bound of yield and the upper bound of error rate for the fraction of signals in which both Alice and Bob send a single-photon pulse to the untrusted third party Charlie. The numerical simulations show that our method with only vacuum+weak decoy state can asymptotically approach the theoretical limit of the infinite number of decoy states. Furthermore, the statistical fluctuation due to the finite length of date is also considered based on the standard statistical analysis.

  5. Quantum transport in topological insulator nanoribbon field effect and Josephson devices

    NASA Astrophysics Data System (ADS)

    Kayyalha, Morteza; Jauregui, Luis; Kazakov, Aleksander; Pettes, Michael; Miotkowski, Ireneusz; Shi, Li; Rokhinson, Leonid; Chen, Yong

    The spin-helical topological surface states (TSS) of topological insulators have attracted great attention in the past few years as an excellent platform to study topological transport and other exotic physics such as Majorana fermions. Here we present experiments studying quantum transport of TSS in topological insulator nanoribbon (TINR) field effect devices with normal as well as superconducting contacts. In Bi2Te3 NRs with normal contacts, we observe that the conductance vs. axial magnetic field exhibits Aharonov-Bohm (AB) oscillations with an alternating phase of zero and π, depending periodically on the Fermi momentum kF tuned by an applied back-gate voltage, consistent with the 1D sub-band structure formed by circumferentially quantized TSS. We also investigated the Josephson effects in BiSbTeSe2 TINRs with superconducting Nb contacts. We measured the gate voltage and temperature dependence of the supercurrent and multiple Andreev reflections (MAR), to probe phase coherent transport via TSS

  6. Interface traps and quantum size effects on the retention time in nanoscale memory devices

    NASA Astrophysics Data System (ADS)

    Mao, Ling-Feng

    2013-08-01

    Based on the analysis of Poisson equation, an analytical surface potential model including interface charge density for nanocrystalline (NC) germanium (Ge) memory devices with p-type silicon substrate has been proposed. Thus, the effects of Pb defects at Si(110)/SiO2, Si(111)/SiO2, and Si(100)/SiO2 interfaces on the retention time have been calculated after quantum size effects have been considered. The results show that the interface trap density has a large effect on the electric field across the tunneling oxide layer and leakage current. This letter demonstrates that the retention time firstly increases with the decrease in diameter of NC Ge and then rapidly decreases with the diameter when it is a few nanometers. This implies that the interface defects, its energy distribution, and the NC size should be seriously considered in the aim to improve the retention time from different technological processes. The experimental data reported in the literature support the theoretical expectation.

  7. Davisson-Germer Prize Talk: Atomically Uniform Thin Films as Quantum Wells and Device Components

    NASA Astrophysics Data System (ADS)

    Chiang, Tai C.

    2015-03-01

    Atomically uniform films can be made for various overlayer-substrate combinations (such as Ag, Pb, Sb, ...on Si, Ge, Fe, ...), many of which are not even lattice matched. These films show remarkable property variations as the film thickness is built up in atomic-layer increments. The thermal stability of the film, its work function, electron-phonon coupling, superconducting transition temperature, etc. exhibit damped and modulated oscillations as the film thickness increases toward the bulk limit. The underlying physics can be understood generally in terms of the energetics of a coarsened electronic structure of thin films and more specifically in terms of a ''one-dimensional shell effect'' - the quantized electronic levels in the film are progressively filled at increasing film thicknesses just like the elemental atomic shells in going through the periodic table. The phase and the amplitude of the oscillations can be tailored by surface/interface engineering that leads to changes in the surface potential and the interface Schottky barrier or band mismatch. These quantum size and confinement effects are important and observable at film thicknesses well in the realm of practical device dimensions and at room temperature, suggesting opportunities for applications. When the films are made of topologically nontrivial materials, the electron spin and its transport become relevant parameters. This talk will discuss issues related to uniform film growth, general trends in connection with reduced dimensions, surprising findings including phonon-mediated pseudogaps, and technology potential.

  8. Measurement-device-independent quantum key distribution with heralded pair coherent state

    NASA Astrophysics Data System (ADS)

    Wang, Xiang; Wang, Yang; Chen, Rui-Ke; Zhou, Chun; Li, Hong-Wei; Bao, Wan-Su

    2016-06-01

    Measurement-device-independent QKD (MDI-QKD) can solve security loophole problems brought by imperfections of detectors and provide enhanced practical security compared to traditional QKD. We propose an active-passive-combined decoy state MDI-QKD protocol with heralded pair coherent state (HPCS) source. By calculating the lower bound of the single-photon counting rate and the upper bound of the single-photon error rate, we present formulas of the secure key rate in our protocol. Based on the linear lossy channel model, we present calculation methods of estimating the overall gain and quantum bit error rate for HPCS source with full phase randomization. We numerically compare secure key rates for different decoy MDI-QKD protocol with different sources. The result shows that the active-passive-combined decoy state MDI-QKD protocol with HPCS source has certain superiority in the secure key rate. It can provide an important theoretical reference for practical implementations of MDI-QKD.

  9. Detection of bacteria in suspension using a superconducting Quantum interference device

    SciTech Connect

    Grossman, H.L.; Myers, W.R.; Vreeland, V.J.; Alper, J.D.; Bertozzi, C.R.; Clarke, J.

    2003-06-09

    We demonstrate a technique for detecting magnetically-labeled Listeria monocytogenes and for measuring the binding rate between antibody-linked magnetic particles and bacteria. This assay, which is both sensitive and straightforward to perform, can quantify specific bacteria in a sample without the need to immobilize the bacteria or wash away unbound magnetic particles. In the measurement, we add 50 nm diameter superparamagnetic particles, coated with antibodies, to a liquid sample containing L. monocytogenes. We apply a pulsed magnetic field to align the magnetic dipole moments and use a high transition temperature Superconducting Quantum Interference Device (SQUID), an extremely sensitive detector of magnetic flux, to measure the magnetic relaxation signal when the field is turned off. Unbound particles randomize direction by Brownian rotation too quickly to be detected. In contrast, particles bound to L. monocytogenes are effectively immobilized and relax in about 1 s by rotation of the internal dipole moment. This Neel relaxation process is detected by the SQUID. The measurements indicate a detection limit of (5.6 {+-} 1.1) x 10{sup 6} L. monocytogenes for a 20 {micro}L sample volume. If the sample volume were reduced to 1 nL, we estimate that the detection limit could be improved to 230 {+-} 40 L. monocytogenes cells. Time-resolved measurements yield the binding rate between the particles and bacteria.

  10. Graphene Quantum Dots Interfaced with Single Bacterial Spore for Bio-Electromechanical Devices: A Graphene Cytobot

    PubMed Central

    Sreeprasad, T. S.; Nguyen, Phong; Alshogeathri, Ahmed; Hibbeler, Luke; Martinez, Fabian; McNeil, Nolan; Berry, Vikas

    2015-01-01

    The nanoarchitecture and micromachinery of a cell can be leveraged to fabricate sophisticated cell-driven devices. This requires a coherent strategy to derive cell's mechanistic abilities, microconstruct, and chemical-texture towards such microtechnologies. For example, a microorganism's hydrophobic membrane encapsulating hygroscopic constituents allows it to sustainably withhold a high aquatic pressure. Further, it provides a rich surface chemistry available for nano-interfacing and a strong mechanical response to humidity. Here we demonstrate a route to incorporate a complex cellular structure into microelectromechanics by interfacing compatible graphene quantum dots (GQDs) with a highly responsive single spore microstructure. A sensitive and reproducible electron-tunneling width modulation of 1.63 nm within a network of GQDs chemically-secured on a spore was achieved via sporal hydraulics with a driving force of 299.75 Torrs (21.7% water at GQD junctions). The electron-transport activation energy and the Coulomb blockade threshold for the GQD network were 35 meV and 31 meV, respectively; while the inter-GQD capacitance increased by 1.12 folds at maximum hydraulic force. This is the first example of nano/bio interfacing with spores and will lead to the evolution of next-generation bio-derived microarchitectures, probes for cellular/biochemical processes, biomicrorobotic-mechanisms, and membranes for micromechanical actuation. PMID:25774962

  11. Graphene Quantum Dots Interfaced with Single Bacterial Spore for Bio-Electromechanical Devices: A Graphene Cytobot

    NASA Astrophysics Data System (ADS)

    Sreeprasad, T. S.; Nguyen, Phong; Alshogeathri, Ahmed; Hibbeler, Luke; Martinez, Fabian; McNeil, Nolan; Berry, Vikas

    2015-03-01

    The nanoarchitecture and micromachinery of a cell can be leveraged to fabricate sophisticated cell-driven devices. This requires a coherent strategy to derive cell's mechanistic abilities, microconstruct, and chemical-texture towards such microtechnologies. For example, a microorganism's hydrophobic membrane encapsulating hygroscopic constituents allows it to sustainably withhold a high aquatic pressure. Further, it provides a rich surface chemistry available for nano-interfacing and a strong mechanical response to humidity. Here we demonstrate a route to incorporate a complex cellular structure into microelectromechanics by interfacing compatible graphene quantum dots (GQDs) with a highly responsive single spore microstructure. A sensitive and reproducible electron-tunneling width modulation of 1.63 nm within a network of GQDs chemically-secured on a spore was achieved via sporal hydraulics with a driving force of 299.75 Torrs (21.7% water at GQD junctions). The electron-transport activation energy and the Coulomb blockade threshold for the GQD network were 35 meV and 31 meV, respectively; while the inter-GQD capacitance increased by 1.12 folds at maximum hydraulic force. This is the first example of nano/bio interfacing with spores and will lead to the evolution of next-generation bio-derived microarchitectures, probes for cellular/biochemical processes, biomicrorobotic-mechanisms, and membranes for micromechanical actuation.

  12. Individual Mammalian Cell Magnetic Measurements with a Superconducting Quantum Interference Device

    NASA Astrophysics Data System (ADS)

    Palmstrom, Johanna C.; Brewer, Kimberly; Tee, Sui Seng; Theis, Eric; Rutt, Brian; Moler, Kathryn A.

    2015-03-01

    Magnetism can be introduced into otherwise nonmagnetic cells by the uptake of superparamagnetic iron oxide (SPIO) nanoparticles. SPIO nanoparticles are used in numerous biomedical applications including cellular therapies and targeted drug delivery. Currently there are few tools capable of characterizing individual magnetic nanoparticles and the magnetic properties of individual mammalian cells loaded with SPIO. Our scanning superconducting quantum interference devices (SQUIDs) are good candidates for these measurements due to their high sensitivity to magnetic dipole moments (approx. 200 μb/ √Hz) In this study, we use a scanning SQUID to image the magnetic flux from SPIO loaded H1299 lung cancer cells. We find that the magnetic moment spatially varies inside the cell with each cell having a unique distribution of moments. We also correlate these magnetic images with optical and scanning electron microscope images. These results show that the SQUID is a useful tool for imaging biological magnetism. The visualization of single cell magnetism and the quantification of magnetic dipole moments in magnetically labeled cells can be used to optimize conventional biological magnetic imaging techniques, such as MRI.

  13. Frequency multiplexed superconducting quantum interference device readout of large bolometer arrays for cosmic microwave background measurements.

    PubMed

    Dobbs, M A; Lueker, M; Aird, K A; Bender, A N; Benson, B A; Bleem, L E; Carlstrom, J E; Chang, C L; Cho, H-M; Clarke, J; Crawford, T M; Crites, A T; Flanigan, D I; de Haan, T; George, E M; Halverson, N W; Holzapfel, W L; Hrubes, J D; Johnson, B R; Joseph, J; Keisler, R; Kennedy, J; Kermish, Z; Lanting, T M; Lee, A T; Leitch, E M; Luong-Van, D; McMahon, J J; Mehl, J; Meyer, S S; Montroy, T E; Padin, S; Plagge, T; Pryke, C; Richards, P L; Ruhl, J E; Schaffer, K K; Schwan, D; Shirokoff, E; Spieler, H G; Staniszewski, Z; Stark, A A; Vanderlinde, K; Vieira, J D; Vu, C; Westbrook, B; Williamson, R

    2012-07-01

    A technological milestone for experiments employing transition edge sensor bolometers operating at sub-Kelvin temperature is the deployment of detector arrays with 100s-1000s of bolometers. One key technology for such arrays is readout multiplexing: the ability to read out many sensors simultaneously on the same set of wires. This paper describes a frequency-domain multiplexed readout system which has been developed for and deployed on the APEX-SZ and South Pole Telescope millimeter wavelength receivers. In this system, the detector array is divided into modules of seven detectors, and each bolometer within the module is biased with a unique ∼MHz sinusoidal carrier such that the individual bolometer signals are well separated in frequency space. The currents from all bolometers in a module are summed together and pre-amplified with superconducting quantum interference devices operating at 4 K. Room temperature electronics demodulate the carriers to recover the bolometer signals, which are digitized separately and stored to disk. This readout system contributes little noise relative to the detectors themselves, is remarkably insensitive to unwanted microphonic excitations, and provides a technology pathway to multiplexing larger numbers of sensors. PMID:22852677

  14. Rotational population patterns and searches for the nuclear SQUID (Superconducting Quantum Interference Device)

    SciTech Connect

    Canto, L.F.; Donangelo, R.J.; Farhan, A.R.; Guidry, M.W.; Rasmussen, J.O.; Ring, P.; Stoyer, M.A. . Inst. de Fisica; Kuwait Univ. . Dept. of Physics; Tennessee Univ., Knoxville, TN . Dept. of Physics; Lawrence Berkeley Lab., CA; Technische Univ. Muenchen, Garching . Physikdepartment; Lawrence Berkeley Lab., CA )

    1989-11-01

    This paper presents new theoretical results for rotational population patterns in the nuclear SQUID effect. (The term nuclear SQUID is in analogy to the solid-state Superconducting Quantum Interference Devices.) The SQUID effect is an interesting new twist to an old quest to understand Coriolis anti-pairing (CAP) effects in nuclear rotational bands. Two-neutron transfer reaction cross sections among high-spin states have long been touted as more specific CAP probes than other nuclear properties. Heavy projectiles like Sn or Pb generally are recommended to pump the deformed nucleus to as high spin as possible for transfer. The interference and sign reversal of 2n transfer amplitudes at high spin, as predicted in the early SQUID work imposes the difficult requirement of Coulomb pumping to near back-bending spins at closest approach. For Pb on rare earths we find a dramatic departure from sudden-approximation, so that the population depression occurs as low as final spin 10h. 14 refs., 8 figs.

  15. The Physics of Quantum Computation

    NASA Astrophysics Data System (ADS)

    Falci, Giuseppe; Paladino, Elisabette

    2015-10-01

    Quantum Computation has emerged in the past decades as a consequence of down-scaling of electronic devices to the mesoscopic regime and of advances in the ability of controlling and measuring microscopic quantum systems. QC has many interdisciplinary aspects, ranging from physics and chemistry to mathematics and computer science. In these lecture notes we focus on physical hardware, present day challenges and future directions for design of quantum architectures.

  16. On-chip integration of suspended InGaN/GaN multiple-quantum-well devices with versatile functionalities.

    PubMed

    Cai, Wei; Yang, Yongchao; Gao, Xumin; Yuan, Jialei; Yuan, Wei; Zhu, Hongbo; Wang, Yongjin

    2016-03-21

    We propose, fabricate and demonstrate on-chip photonic integration of suspended InGaN/GaN multiple quantum wells (MQWs) devices on the GaN-on-silicon platform. Both silicon removal and back wafer etching are conducted to obtain membrane-type devices, and suspended waveguides are used for the connection between p-n junction InGaN/GaN MQWs devices. As an in-plane data transmission system, the middle p-n junction InGaN/GaN MQWs device is used as a light emitting diode (LED) to deliver signals by modulating the intensity of the emitted light, and the other two devices act as photodetectors (PDs) to sense the light guided by the suspended waveguide and convert the photons into electrons, achieving 1 × 2 in-plane information transmission via visible light. Correspondingly, the three devices can function as independent PDs to realize multiple receivers for free space visible light communication. Further, the on-chip photonic platform can be used as an active electro-optical sensing system when the middle device acts as a PD and the other two devices serve as LEDs. The experimental results show that the auxiliary LED sources can enhance the amplitude of the induced photocurrent. PMID:27136794

  17. High-quantum-efficiency 0.5 eV GaInAsSb/GaSb thermophotovoltaic devices

    SciTech Connect

    Wang, C.A.; Choi, H.K.; Ransom, S.L.; Charache, G.W.; Danielson, L.R.; DePoy, D.M.

    1999-08-01

    We report high-performance lattice-matched GaInAsSb/GaSb thermophotovoltaic (TPV) devices with a 0.5 eV band gap. The TPV structures were grown on GaSb substrates by organometallic vapor phase epitaxy at a lower temperature (525 {degree}C compared to 550 {degree}C) to improve the quality of the metastable GaInAsSb alloy. The 0.5 eV TPV devices exhibit external quantum efficiency as high as 60{percent}, which corresponds to an internal quantum efficiency of 90{percent}, assuming 35{percent} reflection losses. This efficiency is comparable to the value measured for 0.53 eV devices. The ratio of the open circuit voltage to band-gap energy ratio decreases from 0.57 for 0.53 eV devices to 0.48 for 0.5 eV devices. {copyright} {ital 1999 American Institute of Physics.}

  18. Cu-In-Ga-S quantum dot composition-dependent device performance of electrically driven light-emitting diodes

    NASA Astrophysics Data System (ADS)

    Kim, Jong-Hoon; Lee, Ki-Heon; Jo, Dae-Yeon; Lee, Yangjin; Hwang, Jun Yeon; Yang, Heesun

    2014-09-01

    Colloidal synthesis of ternary and quaternary quantum dots (QDs) of In/Ga ratio-varied Cu-In1-x-Gax-S (CIGS) with nominal x = 0, 0.5, 0.7, and 1 and their application for the fabrication of quantum dot-light-emitting diodes (QLEDs) are reported. Four QLEDs having CIGS QDs with different compositions are all solution-processed in the framework of multilayered structure, where QD emitting layer is sandwiched by hybrid charge transport layers of poly(9-vinlycarbazole) and ZnO nanoparticles. The device performance such as luminance and efficiency is found to be strongly dependent on the composition of CIGS QDs, and well interpreted by the device energy level diagram proposed through the determination of QD valence band minima by photoelectron emission spectroscopic measurement.

  19. Cu−In−Ga−S quantum dot composition-dependent device performance of electrically driven light-emitting diodes

    SciTech Connect

    Kim, Jong-Hoon; Lee, Ki-Heon; Jo, Dae-Yeon; Yang, Heesun; Lee, Yangjin; Hwang, Jun Yeon

    2014-09-29

    Colloidal synthesis of ternary and quaternary quantum dots (QDs) of In/Ga ratio-varied Cu−In{sub 1−x}−Ga{sub x}−S (CIGS) with nominal x = 0, 0.5, 0.7, and 1 and their application for the fabrication of quantum dot-light-emitting diodes (QLEDs) are reported. Four QLEDs having CIGS QDs with different compositions are all solution-processed in the framework of multilayered structure, where QD emitting layer is sandwiched by hybrid charge transport layers of poly(9-vinlycarbazole) and ZnO nanoparticles. The device performance such as luminance and efficiency is found to be strongly dependent on the composition of CIGS QDs, and well interpreted by the device energy level diagram proposed through the determination of QD valence band minima by photoelectron emission spectroscopic measurement.

  20. Realization of Reliable Solid-State Quantum Memory for Photonic Polarization Qubit

    NASA Astrophysics Data System (ADS)

    Zhou, Zong-Quan; Lin, Wei-Bin; Yang, Ming; Li, Chuan-Feng; Guo, Guang-Can

    2012-05-01

    Faithfully storing an unknown quantum light state is essential to advanced quantum communication and distributed quantum computation applications. The required quantum memory must have high fidelity to improve the performance of a quantum network. Here we report the reversible transfer of photonic polarization states into collective atomic excitation in a compact solid-state device. The quantum memory is based on an atomic frequency comb (AFC) in rare-earth ion-doped crystals. We obtain up to 0.999 process fidelity for the storage and retrieval process of single-photon-level coherent pulse. This reliable quantum memory is a crucial step toward quantum networks based on solid-state devices.

  1. The effects of insertion devices on beam dynamics in the ALS (Advanced Light Source)

    SciTech Connect

    Jackson, A.; Forest, E.; Nishimura, H.; Zisman, M.S.

    1989-03-01

    Third generation synchrotron radiation sources, such as the Advanced Light Source (ALS), are specifically designed to operate with long undulators that produce very high brightness beams of synchrotron radiation. Including such devices in the storage ring magnet lattice introduced extra linear and nonlinear fields that are intrinsic to the undulator. These fields break the symmetry of the lattice and provide driving forces for nonlinear resonances, thereby perturbing the dynamics of the electron motion, particularly at large amplitudes. The main impact of these perturbations is on the beam lifetime, arising out of a reduction of both the transverse acceptance and the momentum acceptance. In this paper, we present the results of an ongoing study of these effects as they relate to the performance of the ALS. 7 refs., 7 figs., 2 tabs.

  2. New chicane magnet design for insertion device straights at the Advanced Light Source

    SciTech Connect

    Marks, Steve; Schlueter, Ross; Anderson, David; Gath, William; Jung, Jin-Young; Robin, David; Steier, Christoph; Stevens, Troy

    2001-12-10

    A chicane magnet incorporating counter-rotating permanent magnet pairs together with trim coils has been designed for use in the Advanced Light Source (ALS) straights in conjunction with two insertion devices. In particular, this design is being developed for use in the existing beam line (BL) 4 elliptically polarizing undulator (EPU) straight and in the BL11 EPU straight, currently under design and construction. The purpose of the chicane is to provide a fixed angular separation between two successive EPU photon fans, and to correct steering perturbations resulting from EPU polarization state changes. Polarization changes occur on the time scale of one second; associated steering corrections must be accomplished in less than a second. Hysteresis associated with conventional iron core electromagnets prevents fast steering correction to the required precision. This consideration motivated the iron-free design presented here.

  3. Advanced Monitoring of Trace Metals Applied to Contamination Reduction of Silicon Device Processing

    NASA Astrophysics Data System (ADS)

    Maillot, P.; Martin, C.; Planchais, A.

    2011-11-01

    The detrimental effects of metallic on certain key electrical parameters of silicon devices mandates the use of state-of-the-art characterization and metrology tools as well as appropriate control plans. Historically, this has been commonly achieved in-line on monitor wafers through a combination of Total Reflectance X-Ray Fluorescence (TXRF) and post anneal Surface Photo Voltage (SPV). On the other hand, VPD (Vapor Phase Decomposition) combined with ICP-MS (Inductively Coupled Mass Spectrometry) or TXRF is known to provide both identification and quantification of surface trace metals at lower detection limits. Based on these considerations the description of an advanced monitoring scheme using SPV, TXRF and automated VPD ICP-MS is described.

  4. Analysis of insertion device magnet measurements for the Advanced Light Source

    SciTech Connect

    Marks, S.; Humphries, D.; Kincaid, B.M.; Schlueter, R.; Wang, C.

    1993-07-01

    The Advanced Light Source (ALS), which is currently being commissioned at Lawrence Berkeley Laboratory, is a third generation light source designed to produce XUV radiation of unprecedented brightness. To meet the high brightness goal the storage ring has been designed for very small electron beam emittance and the undulators installed in the ALS are built to a high degree of precision. The allowable magnetic field errors are driven by electron beam and radiation requirements. Detailed magnetic measurements and adjustments are performed on each undulator to qualify it for installation in the ALS. The first two ALS undulators, IDA and IDB, have been installed. This paper describes the program of measurements, data analysis, and adjustments carried out for these two devices. Calculations of the radiation spectrum, based upon magnetic measurements, are included. Final field integral distributions are also shown. Good field integral uniformity has been achieved using a novel correction scheme, which is also described.

  5. Influence of the asymmetry of the potential on the dynamics of a two-level superconducting quantum interference device qubit

    SciTech Connect

    Aravantinos-Zafiris, Nikolaos; Paspalakis, Emmanuel

    2005-07-15

    We analyze the interaction of a two-level superconducting quantum interference device (SQUID) qubit with a classical microwave pulse. The rf-SQUID is characterized by an asymmetric double well potential that gives rise to diagonal matrix elements. The diagonal matrix elements are accounted for in the interaction of the microwave pulse with the SQUID. We present analytical results that correctly describe the system's dynamics.

  6. Spectral characteristics of insertion device sources at the Advanced Photon Source

    SciTech Connect

    Viccaro, P.J.

    1990-01-01

    The 7-GeV Advanced Photon Source (APS) synchrotron facility at Argonne National Laboratory will be a powerful source of hard x-rays with energies above 1 keV. In addition to the availability of bending magnet radiation, the storage ring will have 35 straight sections for insertion device (ID) x-ray sources. The unique spectral properties and flexibility of these devices open new possibilities for scientific research in essentially every area of science and technology. Existing and new techniques utilizing the full potential of these sources, such as the enhanced coherence, unique polarization properties, and high spectral brilliance, will permit experiments not possible with existing sources. In the following presentation, the spectral properties of ID sources are briefly reviewed. A summary of the specific properties of sources planned for the APS storage ring is then presented. Recent results for APS prototype ID sources are discussed, and finally some special x-ray sources under consideration for the APS facility are described. 9 refs.

  7. Charge-Transfer Mobility Parameters in Photoelectronic Devices: The Advanced Miller-Abrahams Computation.

    PubMed

    Basilevsky, M V; Odinokov, A V; Komarova, K G

    2015-06-18

    The local hopping step of the electron transfer (ET) reaction is investigated for a real organic material composed of molecules M (N,N'-di(1-naphthyl)-N,N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine). This material is implemented in light-emitting photoelectronic devices. The conductivity effect is simulated and calculated at a molecular level. We have studied the ET mechanism alternative to that suggested by the usually employed Marcus-like polaron model. The ion-molecular binary complex M(+)M (for hole transfer) is considered as a reaction center. The reaction dynamics is carried through the low-frequency intermolecular vibration coordinate connecting its fragments (the promotion mode). Its coupling to the acoustic phonon bath serves for a dissipation of the reaction energy misfit. The high-frequency intramolecular vibrations (the reorganization modes) modulate the reaction kinetics via Franck-Condon factors induced by their polarization. The ET rate constants are evaluated in terms of the computational algorithm described earlier (Basilevsky, M. V.; et al. J. Chem. Phys. 2013 139, 234102). Standard quantum-chemical and molecular dynamical techniques are used for a calculation of all necessary parameters of this model. The macroscopic charge-carrier mobility of the material is estimated by properly averaging the rate constants over the total simulation cell. PMID:25636079

  8. Silicon high speed modulator for advanced modulation: device structures and exemplary modulator performance

    NASA Astrophysics Data System (ADS)

    Milivojevic, Biljana; Wiese, Stefan; Whiteaway, James; Raabe, Christian; Shastri, Anujit; Webster, Mark; Metz, Peter; Sunder, Sanjay; Chattin, Bill; Anderson, Sean P.; Dama, Bipin; Shastri, Kal

    2014-03-01

    Fiber optics is well established today due to the high capacity and speed, unrivaled flexibility and quality of service. However, state of the art optical elements and components are hardly scalable in terms of cost and size required to achieve competitive port density and cost per bit. Next-generation high-speed coherent optical communication systems targeting a data rate of 100-Gb/s and beyond goes along with innovations in component and subsystem areas. Consequently, by leveraging the advanced silicon micro and nano-fabrication technologies, significant progress in developing CMOS platform-based silicon photonic devices has been made all over the world. These achievements include the demonstration of high-speed IQ modulators, which are important building blocks in coherent optical communication systems. In this paper, we demonstrate silicon photonic QPSK modulator based on a metal-oxide-semiconductor (MOS) capacitor structure, address different modulator configuration structures and report our progress and research associated with highspeed advanced optical modulation in silicon photonics

  9. Device architecture engineering in polymer/ZnO quantum dots/ZnO array ternary hybrid solar cells

    NASA Astrophysics Data System (ADS)

    Wu, Fan; Zhao, Yu; Zhang, Hui; Tong, Yanhua

    2015-09-01

    Hybrid solar cells (HSCs) based on pristine ZnO nanorod array (ZnO-NRA) and conjugated polymer with ordinary inverted device architecture normally perform low open-circuit voltage ( V oc) and short-circuit current density ( J sc). This paper compares three improved device architectures for preparation of efficient polymer/ZnO-NRA HSCs by incorporating ZnO quantum dots (ZnO-QDs) into device with different engineering. It is found that when growth of ZnO-QDs on ZnO nanorod surface to formation of homostructured ZnO core-shell array (ZnO-CSA) instead of pristine ZnO-NRA can significantly increase the device V oc, while blending ZnO-QDs into MEH-PPV between nanorods can significantly increase the device J sc. The best photovoltaic performance is realized in the architecture consisting of ZnO-CSA as well as blends of MEH-PPV and ZnO-QDs, in which the V oc and J sc can be significant enhanced simultaneously. The present study reports the architecture-related device performances in polymer/ZnO-NRA solar cells, which will help to guide the design of HSCs or related optoelectronic devices.

  10. Effect of phase transition on quantum transport in group-IV two-dimensional U-shape device

    SciTech Connect

    Sadi, Mohammad Abdullah; Gupta, Gaurav Liang, Gengchiau

    2014-10-21

    The effect of phase-transition from the quantum-spin-hall to the band-insulator phase on the transport through a three-terminal U-shape spin-separator has been computationally investigated via non-equilibrium green function formalism. Two-dimensional group-IV elements have been comprehensively appraised as the device material. The device separates the unpolarized current injected at the source-terminal into nearly 100% spin-polarized currents of the opposite polarities at the two drain terminals. The phase-transition activated by the electric-field orthogonal to the device is shown to extensively influence the current magnitude and its spin-polarization, and the effect is stronger for materials with smaller intrinsic spin-orbit coupling. Moreover, the device length and the area under field are shown to critically affect the device characteristics on phase change. It is shown that the same device can be operated as a spin-filter by inducing phase-transition selectively in the channel. The results are important for designing spin-devices from Group-IV monolayers.

  11. Low-temperature-grown InGaAs quantum wells for optical device applications

    NASA Astrophysics Data System (ADS)

    Juodawlkis, Paul William

    1999-11-01

    The large optical absorption and carrier-induced nonlinearities of semiconductor materials are useful for optical signal processing applications. For absorptive devices operating at ultrafast data rates (>100 Gb/s) or high optical intensities, it is necessary to reduce the intrinsic photo-excited carrier removal time. One method of achieving this reduction is to increase the nonradiative recombination rate through the controlled introduction of defects. In this thesis, we explore the use of low-temperature molecular-beam epitaxy (MBE) to introduce nonradiative recombination centers into InGaAs-based quantum-wells (QWs). The objectives of the thesis are: (i)to improve the understanding of the optoelectronic properties of low-temperature-grown (LTG) InGaAs/InAlAs QWs, and (ii)to assess the feasibility of using these materials for optical device applications in the 1.5-μm wavelength region. Time-resolved differential transmission measurements reveal that the nonlinear absorption recovery time in InGaAs/InAlAs QWs can be reduced from >100 ps to 0.6 ps through the combination of low-temperature growth (~250°C) and beryllium (Be) doping. The bandedge absorption slope and the nonlinear absorption cross- section are only diminished by factors of 2 to 3 relative to QWs grown at standard temperature (~500°C). The Be doping dependence of the recovery time and the residual electron density in the LTG-QWs can be mainly attributed to impurity-related compensation. Be doping also maintains the ultrafast recovery following thermal anneal. The recovery response results from fast electron- trapping followed by slow (>100 ps) trapped- electron/free-hole recombination. Detailed simulations of the nonlinear absorption saturation and recovery processes agree quantitatively with measured data and substantiate the importance of the photo-excitation wavelength on the observed recovery response. The absorption saturation model includes the competition between band-filling and band

  12. Study of a prototype high quantum efficiency thick scintillation crystal video-electronic portal imaging device

    SciTech Connect

    Samant, Sanjiv S.; Gopal, Arun

    2006-08-15

    Image quality in portal imaging suffers significantly from the loss in contrast and spatial resolution that results from the excessive Compton scatter associated with megavoltage x rays. In addition, portal image quality is further reduced due to the poor quantum efficiency (QE) of current electronic portal imaging devices (EPIDs). Commercial video-camera-based EPIDs or VEPIDs that utilize a thin phosphor screen in conjunction with a metal buildup plate to convert the incident x rays to light suffer from reduced light production due to low QE (<2% for Eastman Kodak Lanex Fast-B). Flat-panel EPIDs that utilize the same luminescent screen along with an a-Si:H photodiode array provide improved image quality compared to VEPIDs, but they are expensive and can be susceptible to radiation damage to the peripheral electronics. In this article, we present a prototype VEPID system for high quality portal imaging at sub-monitor-unit (subMU) exposures based on a thick scintillation crystal (TSC) that acts as a high QE luminescent screen. The prototype TSC system utilizes a 12 mm thick transparent CsI(Tl) (thallium-activated cesium iodide) scintillator for QE=0.24, resulting in significantly higher light production compared to commercial phosphor screens. The 25x25 cm{sup 2} CsI(Tl) screen is coupled to a high spatial and contrast resolution Video-Optics plumbicon-tube camera system (1240x1024 pixels, 250 {mu}m pixel width at isocenter, 12-bit ADC). As a proof-of-principle prototype, the TSC system with user-controlled camera target integration was adapted for use in an existing clinical gantry (Siemens BEAMVIEW{sup PLUS}) with the capability for online intratreatment fluoroscopy. Measurements of modulation transfer function (MTF) were conducted to characterize the TSC spatial resolution. The measured MTF along with measurements of the TSC noise power spectrum (NPS) were used to determine the system detective quantum efficiency (DQE). A theoretical expression of DQE(0) was

  13. Study of a prototype high quantum efficiency thick scintillation crystal video-electronic portal imaging device.

    PubMed

    Samant, Sanjiv S; Gopal, Arun

    2006-08-01

    Image quality in portal imaging suffers significantly from the loss in contrast and spatial resolution that results from the excessive Compton scatter associated with megavoltage x rays. In addition, portal image quality is further reduced due to the poor quantum efficiency (QE) of current electronic portal imaging devices (EPIDs). Commercial video-camera-based EPIDs or VEPIDs that utilize a thin phosphor screen in conjunction with a metal buildup plate to convert the incident x rays to light suffer from reduced light production due to low QE (<2% for Eastman Kodak Lanex Fast-B). Flat-panel EPIDs that utilize the same luminescent screen along with an a-Si:H photodiode array provide improved image quality compared to VEPIDs, but they are expensive and can be susceptible to radiation damage to the peripheral electronics. In this article, we present a prototype VEPID system for high quality portal imaging at sub-monitor-unit (subMU) exposures based on a thick scintillation crystal (TSC) that acts as a high QE luminescent screen. The prototype TSC system utilizes a 12 mm thick transparent CsI(Tl) (thallium-activated cesium iodide) scintillator for QE=0.24, resulting in significantly higher light production compared to commercial phosphor screens. The 25 X 25 cm2 CsI(Tl) screen is coupled to a high spatial and contrast resolution Video-Optics plumbicon-tube camera system (1240 X 1024 pixels, 250 microm pixel width at isocenter, 12-bit ADC). As a proof-of-principle prototype, the TSC system with user-controlled camera target integration was adapted for use in an existing clinical gantry (Siemens BEAMVIEW(PLUS)) with the capability for online intratreatment fluoroscopy. Measurements of modulation transfer function (MTF) were conducted to characterize the TSC spatial resolution. The measured MTF along with measurements of the TSC noise power spectrum (NPS) were used to determine the system detective quantum efficiency (DQE). A theoretical expression of DQE(0) was developed

  14. Nano Superconducting Quantum Interference device: A powerful tool for nanoscale investigations

    NASA Astrophysics Data System (ADS)

    Granata, Carmine; Vettoliere, Antonio

    2016-02-01

    The magnetic sensing at nanoscale level is a promising and interesting research topic of nanoscience. Indeed, magnetic imaging is a powerful tool for probing biological, chemical and physical systems. The study of small spin cluster, like magnetic molecules and nanoparticles, single electron, cold atom clouds, is one of the most stimulating challenges of applied and basic research of the next years. In particular, the magnetic nanoparticle investigation plays a fundamental role for the modern material science and its relative technological applications like ferrofluids, magnetic refrigeration and biomedical applications, including drug delivery, hyper-thermia cancer treatment and magnetic resonance imaging contrast-agent. Actually, one of the most ambitious goals of the high sensitivity magnetometry is the detection of elementary magnetic moment or spin. In this framework, several efforts have been devoted to the development of a high sensitivity magnetic nanosensor pushing sensing capability to the individual spin level. Among the different magnetic sensors, Superconducting QUantum Interference Devices (SQUIDs) exhibit an ultra high sensitivity and are widely employed in numerous applications. Basically, a SQUID consists of a superconducting ring (sensitive area) interrupted by two Josephson junctions. In the recent years, it has been proved that the magnetic response of nano-objects can be effectively measured by using a SQUID with a very small sensitive area (nanoSQUID). In fact, the sensor noise, expressed in terms of the elementary magnetic moment (spin or Bohr magneton), is linearly dependent on the SQUID loop side length. For this reason, SQUIDs have been progressively miniaturized in order to improve the sensitivity up to few spin per unit of bandwidth. With respect to other techniques, nanoSQUIDs offer the advantage of direct measurement of magnetization changes in small spin systems. In this review, we focus on nanoSQUIDs and its applications. In

  15. Study of the detective quantum efficiency for the kinestatic charge detector as a megavoltage imaging device

    NASA Astrophysics Data System (ADS)

    Samant, Sanjiv S.; Gopal, Arun; DiBianca, Frank A.

    2003-06-01

    Megavoltage x-ray imaging suffers from relatively poor contrast and spatial resolution compared to diagnostic kilovoltage x-ray imaging due to the dominant Compton scattering in the former. Recently available amorphous silicon/selenium based flat-panel imagers overcome many of the limitations of poor contrast and spatial resolution that affect conventional video based electronic portal imaging devices (EPIDs). An alternative technology is presented here: kinestatic charge detection (KCD). The KCD uses a slot photon beam, high-pressure gas (xenon, 100 atm) and a multi-ion rectangular chamber in scanning mode. An electric field is used to regulate the cation drift velocity. By matching the scanning speed with that of the cation drift, the cations remain static in the object frame of reference, allowing temporal integration of the signal. KCD imaging is characterized by reduced scatter and a high signal-to-noise ratio. Measurements and Monte Carlo simulations of modulation transfer function (MTF), noise power spectrum (NPS) and the detective quantum efficiency (DQE) of a prototype small field of view KCD detector (384 channels, 0.5 mm spacing) were carried out. Measurements yield DQE[0]=0.19 and DQE[0.5cy/mm]=0.01. KCD imaging is compared to film and commercial EPID systems using phantoms, with the KCD requiring an extremely low dose (0.1 cGy) per image. A proposed cylindrical chamber design with a higher ion-collection depth is expected to further improve image quality (DQE[0]>0.25).

  16. An ultralow noise current amplifier based on superconducting quantum interference device for high sensitivity applications.

    PubMed

    Granata, C; Vettoliere, A; Russo, M

    2011-01-01

    An integrated ultrahigh sensitive current amplifier based on a niobium dc superconducting quantum interference device (SQUID) has been developed. The sensor design is based on a multiturn signal coil coupled to a suitable SQUID magnetometer. The signal coil consists of 60 square niobium turns tightly coupled to a superconducting flux transformer of a SQUID magnetometer. The primary coil (pick-up coil) of the flux transformer has been suitably designed in order to accommodate the multiturn input coil. It has a side length of 10 mm and a width of 2.4 mm. In such a way we have obtained a signal current to magnetic flux transfer coefficient (current sensitivity) as low as 62 nA∕Φ(0). The sensor has been characterized in liquid helium by using a direct coupling low noise readout electronic and a standard modulated electronic in flux locked loop configuration for the noise measurements. Beside the circuit complexity, the sensor has exhibited a smooth and free resonance voltage-flux characteristic guaranteeing a reliable and a stable working operation. Considering a SQUID magnetic flux noise of S(Φ)(1∕2) = 1.8 μΦ(0)∕Hz(1∕2) at T = 4.2 K, a current noise as low as 110 fA∕Hz(1∕2) is obtained. Such a value is about a factor two less than the noise of other SQUIDs of the same category. As an application, Nyquist noise measurements of integrated test resistors using the current sensing noise thermometer technique are reported. Due to its high performance such a sensor can be employed in all applications requiring an extremely current sensitivity like the readout of the gravitational wave detectors and the current sensing noise thermometry. PMID:21280839

  17. Roadmap on quantum optical systems

    NASA Astrophysics Data System (ADS)

    Dumke, Rainer; Lu, Zehuang; Close, John; Robins, Nick; Weis, Antoine; Mukherjee, Manas; Birkl, Gerhard; Hufnagel, Christoph; Amico, Luigi; Boshier, Malcolm G.; Dieckmann, Kai; Li, Wenhui; Killian, Thomas C.

    2016-09-01

    This roadmap bundles fast developing topics in experimental optical quantum sciences, addressing current challenges as well as potential advances in future research. We have focused on three main areas: quantum assisted high precision measurements, quantum information/simulation, and quantum gases. Quantum assisted high precision measurements are discussed in the first three sections, which review optical clocks, atom interferometry, and optical magnetometry. These fields are already successfully utilized in various applied areas. We will discuss approaches to extend this impact even further. In the quantum information/simulation section, we start with the traditionally successful employed systems based on neutral atoms and ions. In addition the marvelous demonstrations of systems suitable for quantum information is not progressing, unsolved challenges remain and will be discussed. We will also review, as an alternative approach, the utilization of hybrid quantum systems based on superconducting quantum devices and ultracold atoms. Novel developments in atomtronics promise unique access in exploring solid-state systems with ultracold gases and are investigated in depth. The sections discussing the continuously fast-developing quantum gases include a review on dipolar heteronuclear diatomic gases, Rydberg gases, and ultracold plasma. Overall, we have accomplished a roadmap of selected areas undergoing rapid progress in quantum optics, highlighting current advances and future challenges. These exciting developments and vast advances will shape the field of quantum optics in the future.

  18. Relativistic quantum metrology: exploiting relativity to improve quantum measurement technologies.

    PubMed

    Ahmadi, Mehdi; Bruschi, David Edward; Sabín, Carlos; Adesso, Gerardo; Fuentes, Ivette

    2014-01-01

    We present a framework for relativistic quantum metrology that is useful for both Earth-based and space-based technologies. Quantum metrology has been so far successfully applied to design precision instruments such as clocks and sensors which outperform classical devices by exploiting quantum properties. There are advanced plans to implement these and other quantum technologies in space, for instance Space-QUEST and Space Optical Clock projects intend to implement quantum communications and quantum clocks at regimes where relativity starts to kick in. However, typical setups do not take into account the effects of relativity on quantum properties. To include and exploit these effects, we introduce techniques for the application of metrology to quantum field theory. Quantum field theory properly incorporates quantum theory and relativity, in particular, at regimes where space-based experiments take place. This framework allows for high precision estimation of parameters that appear in quantum field theory including proper times and accelerations. Indeed, the techniques can be applied to develop a novel generation of relativistic quantum technologies for gravimeters, clocks and sensors. As an example, we present a high precision device which in principle improves the state-of-the-art in quantum accelerometers by exploiting relativistic effects. PMID:24851858

  19. Relativistic Quantum Metrology: Exploiting relativity to improve quantum measurement technologies

    PubMed Central

    Ahmadi, Mehdi; Bruschi, David Edward; Sabín, Carlos; Adesso, Gerardo; Fuentes, Ivette

    2014-01-01

    We present a framework for relativistic quantum metrology that is useful for both Earth-based and space-based technologies. Quantum metrology has been so far successfully applied to design precision instruments such as clocks and sensors which outperform classical devices by exploiting quantum properties. There are advanced plans to implement these and other quantum technologies in space, for instance Space-QUEST and Space Optical Clock projects intend to implement quantum communications and quantum clocks at regimes where relativity starts to kick in. However, typical setups do not take into account the effects of relativity on quantum properties. To include and exploit these effects, we introduce techniques for the application of metrology to quantum field theory. Quantum field theory properly incorporates quantum theory and relativity, in particular, at regimes where space-based experiments take place. This framework allows for high precision estimation of parameters that appear in quantum field theory including proper times and accelerations. Indeed, the techniques can be applied to develop a novel generation of relativistic quantum technologies for gravimeters, clocks and sensors. As an example, we present a high precision device which in principle improves the state-of-the-art in quantum accelerometers by exploiting relativistic effects. PMID:24851858

  20. Relativistic Quantum Metrology: Exploiting relativity to improve quantum measurement technologies

    NASA Astrophysics Data System (ADS)

    Ahmadi, Mehdi; Bruschi, David Edward; Sabín, Carlos; Adesso, Gerardo; Fuentes, Ivette

    2014-05-01

    We present a framework for relativistic quantum metrology that is useful for both Earth-based and space-based technologies. Quantum metrology has been so far successfully applied to design precision instruments such as clocks and sensors which outperform classical devices by exploiting quantum properties. There are advanced plans to implement these and other quantum technologies in space, for instance Space-QUEST and Space Optical Clock projects intend to implement quantum communications and quantum clocks at regimes where relativity starts to kick in. However, typical setups do not take into account the effects of relativity on quantum properties. To include and exploit these effects, we introduce techniques for the application of metrology to quantum field theory. Quantum field theory properly incorporates quantum theory and relativity, in particular, at regimes where space-based experiments take place. This framework allows for high precision estimation of parameters that appear in quantum field theory including proper times and accelerations. Indeed, the techniques can be applied to develop a novel generation of relativistic quantum technologies for gravimeters, clocks and sensors. As an example, we present a high precision device which in principle improves the state-of-the-art in quantum accelerometers by exploiting relativistic effects.

  1. Improvement of Efficiency and Brightness of Red Organic Light-Emitting Devices Using Double-Quantum-Well Configuration

    NASA Astrophysics Data System (ADS)

    Mi, Rui; Cheng, Gang; Zhao, Yi; Xie, Wen-Fa; Hou, Jing-Ying; Ding, Tao; Liu, Shi-Yong

    2004-03-01

    We present red double-quantum-well organic light-emitting devices (DQW-OLEDs), in which N,N-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyo-4,4'-diamine (NPB) is used as potential barriers and hole transport layer, 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-thtramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) doped tris (8-hydroxyquinoline) aluminium (Alq3) as potential wells and emitter, undoped Alq3 as electron transport layer, respectively. The turn-on voltage is about 4 V. The maximum brightness and electroluminescent (EL) efficiency of the DQW device can reach 5916 cd m-2 at 16 V and 2.85 cd A-1 at 7 V, respectively. In addition, the EL efficiency of the DQW device is relatively independent of the drive voltage in the range from 5 V to 16 V.

  2. Influence of etching processes on electronic transport in mesoscopic InAs/GaSb quantum well devices

    SciTech Connect

    Pal, Atindra Nath; Müller, Susanne; Ihn, Thomas; Ensslin, Klaus; Tschirky, Thomas; Charpentier, Christophe; Wegscheider, Werner

    2015-07-15

    We report the electronic characterization of mesoscopic Hall bar devices fabricated from coupled InAs/GaSb quantum wells sandwiched between AlSb barriers, an emerging candidate for two-dimensional topological insulators. The electronic width of the etched structures was determined from the low field magneto-resistance peak, a characteristic signature of partially diffusive boundary scattering in the ballistic limit. In case of dry-etching the electronic width was found to decrease with electron density. In contrast, for wet etched devices it stayed constant with density. Moreover, the boundary scattering was found to be more specular for wet-etched devices, which may be relevant for studying topological edge states.

  3. Intermediate-band photosensitive device with quantum dots embedded in energy fence barrier

    DOEpatents

    Forrest, Stephen R.; Wei, Guodan

    2010-07-06

    A plurality of layers of a first semiconductor material and a plurality of dots-in-a-fence barriers disposed in a stack between a first electrode and a second electrode. Each dots-in-a-fence barrier consists essentially of a plurality of quantum dots of a second semiconductor material embedded between and in direct contact with two layers of a third semiconductor material. Wave functions of the quantum dots overlap as at least one intermediate band. The layers of the third semiconductor material are arranged as tunneling barriers to require a first electron and/or a first hole in a layer of the first material to perform quantum mechanical tunneling to reach the second material within a respective quantum dot, and to require a second electron and/or a second hole in a layer of the first semiconductor material to perform quantum mechanical tunneling to reach another layer of the first semiconductor material.

  4. Characterization of a linear device developed for research on advanced plasma imaging and dynamics.

    PubMed

    Chung, J; Lee, K D; Seo, D C; Nam, Y U; Choi, M C

    2010-10-01

    Within the scope of long term research on imaging diagnostics for steady-state plasmas and understanding of edge plasma physics through diagnostics with conventional spectroscopic methods, we have constructed a linear electron cyclotron resonance (ECR) plasma device named Research on Advanced Plasma Imaging and Dynamics (RAPID). It has a variety of axial magnetic field profiles provided by eight water-cooled magnetic coils and two dc power supplies. The positions of the magnetic coils are freely adjustable along the axial direction and the power supplies can be operated with many combinations of electrical wiring to the coils. Here, a 6 kW 2.45 GHz magnetron is used to produce steady-state hydrogen, helium, and argon plasmas with central magnetic fields of 875 and/or 437.5 G (second harmonic). In order to achieve the highest possible plasma performance within the limited input parameters, wall conditioning experiments were carried out. Chamber bake-out was achieved with heating coils that were wound covering the vessel, and long-pulse electron cyclotron heating discharge cleaning was also followed after 4 days of bake-out. A uniform bake-out temperature (150 °C) was achieved by wrapping the vessel in high temperature thermal insulation textile and by controlling the heating coil current using a digital control system. The partial pressure changes were observed using a residual gas analyzer, and a total system pressure of 5×10(-8) Torr was finally reached. Diagnostic systems including a millimeter-wave interferometer, a high resolution survey spectrometer, a Langmuir probe, and an ultrasoft x-ray detector were used to provide the evidence that the plasma performance was improved as we desired. In this work, we present characterization of the RAPID device for various system conditions and configurations. PMID:21033972

  5. A microtomography beamline at the Louisiana State University Center for Advanced Microstructures and Devices synchrotron

    NASA Astrophysics Data System (ADS)

    Ham, Kyungmin; Jin, Hua; Butler, Leslie G.; Kurtz, Richard L.

    2002-03-01

    A microtomography beamline has been recently assembled and is currently operating at the Louisiana State University's Center for Advanced Microstructures and Devices synchrotron (CAMD). It has been installed on a bending magnet white-light beamline at port 7A. With the storage ring operating at 1.5 GeV, this beamline has a maximum usable x-ray energy of ˜15 keV. The instrumentation consists of computer-controlled positioning stages for alignment and rotation, a CsI(Tl) phosphor screen, a reflecting mirror, a microscope objective (1:1, 1:4), and Linux/LabVIEW-controlled charge coupled device. With the 1:4 objective, the maximum spatial resolution is 2.25 μm. The positioning and image acquisition computers communicate via transfer control protocol/internet protocol (TCP/IP). A small G4/Linux cluster has been installed for the purpose of on-site reconstruction. Instrument, alignment and reconstruction programs are written in MATLAB, IDL, and C. The applications to date are many and we present several examples. Several biological samples have been studied as part of an effort on biological visualization and computation. Future improvements to this microtomography station include the addition of a double-multilayer monochromator, allowing one to evaluate the three-dimensional elemental composition of materials. Plans also include eventual installation at the CAMD 7 T wiggler beamline, providing x rays in excess of 50 keV to provide better penetration of higher mass-density materials.

  6. Characterization of a linear device developed for research on advanced plasma imaging and dynamics

    SciTech Connect

    Chung, J.; Lee, K. D.; Seo, D. C.; Nam, Y. U.; Choi, M. C.

    2010-10-15

    Within the scope of long term research on imaging diagnostics for steady-state plasmas and understanding of edge plasma physics through diagnostics with conventional spectroscopic methods, we have constructed a linear electron cyclotron resonance (ECR) plasma device named Research on Advanced Plasma Imaging and Dynamics (RAPID). It has a variety of axial magnetic field profiles provided by eight water-cooled magnetic coils and two dc power supplies. The positions of the magnetic coils are freely adjustable along the axial direction and the power supplies can be operated with many combinations of electrical wiring to the coils. Here, a 6 kW 2.45 GHz magnetron is used to produce steady-state hydrogen, helium, and argon plasmas with central magnetic fields of 875 and/or 437.5 G (second harmonic). In order to achieve the highest possible plasma performance within the limited input parameters, wall conditioning experiments were carried out. Chamber bake-out was achieved with heating coils that were wound covering the vessel, and long-pulse electron cyclotron heating discharge cleaning was also followed after 4 days of bake-out. A uniform bake-out temperature (150 deg. C) was achieved by wrapping the vessel in high temperature thermal insulation textile and by controlling the heating coil current using a digital control system. The partial pressure changes were observed using a residual gas analyzer, and a total system pressure of 5x10{sup -8} Torr was finally reached. Diagnostic systems including a millimeter-wave interferometer, a high resolution survey spectrometer, a Langmuir probe, and an ultrasoft x-ray detector were used to provide the evidence that the plasma performance was improved as we desired. In this work, we present characterization of the RAPID device for various system conditions and configurations.

  7. Mandibular advancement devices: indications and predictors of treatment outcome. A review.

    PubMed

    Cuccia, A M; Caradonna, C

    2007-09-01

    Obstructive sleep apnea syndrome (OSAS) is a chronic sleep and respiratory disorder, which causes a partial or total obstruction of the air passage at the upper airway level. Mandibular advancement devices (MADs) have been used in the treatment of snoring, but may be a valid alternative to the continuous nasal positive airway pressure (CPAP) for certain OSAS cases. Therapy by means of MADs arises the interest of the scientific community and now there are many sleep-centres where dentists work as experts in sleep disorders. MADs are instruments of value because they are simple to use, reversible, portable and they generally have a low complication rate. They mechanically increase the oropharyngeal space by advancing the mandible and/or the tongue and reduce pharyngeal collapsibility. More than 60 different MADs are in use, with considerable variations in design. Several studies show that their systematic use produces an evident improvement in the global quality of life as well as in the symptoms of patients with OSAS, especially sleepiness. Even though significant progress has been made in proving the efficacy of MADs for OSAS, the ability to predict the treatment outcome and hence pre-select suitable candidates for this treatment still remains in its early stage. The first aim of this review is to supply to the clinician informations on the cephalometric and polysomnographic parameters that can be used to predict the efficacy of the outcome of MAD therapy in OSAS. Moreover, we examine the cases for which the use of a MAD is indicated. PMID:17938623

  8. Recent Advances in Low-Bandgap, InP-Based GaInAs/InAsP Materials and Devices for Thermophotovoltaic (TPV) Energy Conversion

    NASA Astrophysics Data System (ADS)

    Wanlass, M. W.; Ahrenkiel, S. P.; Ahrenkiel, R. K.; Carapella, J. J.; Wehrer, R. J.; Wernsman, B.

    2004-11-01

    Salient advances in the development of thermophotovoltaic (TPV) energy converters based on low-bandgap, InP-based, GaInAs/InAsP heterostructures are presented and discussed. InP-based materials are well-suited and advantageous for TPV converter applications. Substantial improvements in the quality of lattice-mismatched (LMM) heterostructures have been realized through an enhanced understanding of the relaxation behavior, and associated microstructure, of InAsP compositionally graded layers and GaInAs/InAsP interfaces. Double-heterostructure, GaInAs/InAsP test structures with bandgaps as low as 0.5 eV (1.6% lattice mismatch) have been demonstrated with exceptional low-injection, minority-carrier lifetimes (several μs) and large estimated diffusion lengths — comparable to those for lattice-matched materials. The advances in material quality have contributed to a number of notable TPV device achievements. A record in-cavity efficiency of 23.6% was reported for a 0.6-eV, GaInAs/InAsP monolithic interconnected module. Additionally, 0.52-eV GaInAs/InAsP TPV converters were demonstrated with near-unity internal quantum efficiencies and reverse-saturation current densities nearly equaling the best reported for lattice-matched, 0.52-eV GaInAsSb/GaSb devices. Furthermore, InP-based, 0.74/0.63-eV, monolithic, series-connected, tandem TPV converters are also under development and show promising performance; an in-cavity efficiency of 11% has been reported for preliminary devices.

  9. Teaching Advanced Operation of an iPod-Based Speech-Generating Device to Two Students with Autism Spectrum Disorders

    ERIC Educational Resources Information Center

    Achmadi, Donna; Kagohara, Debora M.; van der Meer, Larah; O'Reilly, Mark F.; Lancioni, Giulio E.; Sutherland, Dean; Lang, Russell; Marschik, Peter B.; Green, Vanessa A.; Sigafoos, Jeff

    2012-01-01

    We evaluated a program for teaching two adolescents with autism spectrum disorders (ASD) to perform more advanced operations on an iPod-based speech-generating device (SGD). The effects of the teaching program were evaluated in a multiprobe multiple baseline across participants design that included two intervention phases. The first intervention…

  10. Return on Investment and Technology-Based Training--An Introduction and a Case Study at Advanced Micro Devices.

    ERIC Educational Resources Information Center

    Masumian, Bijan

    1999-01-01

    Summarizes findings from studies comparing classroom and technology-based approaches to training and the respective Return on Investment (ROI) data. Highlights several advantages of technology-based training. Offers information and initial ROI numbers on the use of technology-based training at Advanced Micro Devices, a global manufacturer of…

  11. Improving Efficiency of III-N Quantum Well Based Optoelectronic Devices through Active Region Design and Growth Techniques

    NASA Astrophysics Data System (ADS)

    Young, Nathan Garrett

    The III-Nitride materials system provides a fascinating platform for developing optoelectronic devices, such as solar cells and LEDs, which have the power to dramatically improve the efficiency of our power consumption and reduce our environmental footprint. Finding ways to make these devices more efficient is key to driving their widespread adoption. This dissertation focuses on the intersection of challenges in physics and metalorganic chemical vapor deposition (MOCVD) growth at the nanoscale when designing for device efficiency. In order to create the best possible InGaN solar cell, a multiple quantum well (MQW) active region design had to be employed to prevent strain relaxation related degradation. There were two competing challenges for MQW active region design and growth. First, it was observed current collection efficiency improved with thinner quantum barriers, which promoted efficient tunneling transport instead of inefficiency thermally activated escape. Second, GaN barriers could planarize surface defects in the MQW region under the right conditions and when grown thick enough. A two-step growth method for thinner quantum barriers was developed that simultaneously allowed for tunneling transport and planarized V-defects. Barriers as thin as 4 nm were employed in MQW active regions with up to 30 periods without structural or electrical degradation, leading to record performance. Application of dielectric optical coatings greatly reduced surface reflections and allowed a second pass of light through the device. This both demonstrated the feasibility of multijunction solar integration and boosted conversion efficiency to record levels for an InGaN solar cell. III-N LEDs have achieved state-of-the-art performance for decades, but still suffer from the phenomena of efficiency droop, where device efficiency drops dramatically at high power operation. Droop is exacerbated by the polarization-induced electric fields in InGaN quantum wells, which originate from

  12. Chemical Compass Model for Avian Magnetoreception as a Quantum Coherent Device

    NASA Astrophysics Data System (ADS)

    Cai, Jianming; Plenio, Martin B.

    2013-12-01

    It is known that more than 50 species use the Earth’s magnetic field for orientation and navigation. Intensive studies, particularly behavior experiments with birds, provide support for a chemical compass based on magnetically sensitive free radical reactions as a source of this sense. However, the fundamental question of how quantum coherence plays an essential role in such a chemical compass model of avian magnetoreception yet remains controversial. Here, we show that the essence of the chemical compass model can be understood in analogy to a quantum interferometer exploiting global quantum coherence rather than any subsystem coherence. Within the framework of quantum metrology, we quantify global quantum coherence and correlate it with the function of chemical magnetoreception. Our results allow us to understand and predict how various factors can affect the performance of a chemical compass from the unique perspective of quantum coherence assisted metrology. This represents a crucial step to affirm a direct connection between quantum coherence and the function of a chemical compass.

  13. Chemical compass model for avian magnetoreception as a quantum coherent device.

    PubMed

    Cai, Jianming; Plenio, Martin B

    2013-12-01

    It is known that more than 50 species use the Earth's magnetic field for orientation and navigation. Intensive studies, particularly behavior experiments with birds, provide support for a chemical compass based on magnetically sensitive free radical reactions as a source of this sense. However, the fundamental question of how quantum coherence plays an essential role in such a chemical compass model of avian magnetoreception yet remains controversial. Here, we show that the essence of the chemical compass model can be understood in analogy to a quantum interferometer exploiting global quantum coherence rather than any subsystem coherence. Within the framework of quantum metrology, we quantify global quantum coherence and correlate it with the function of chemical magnetoreception. Our results allow us to understand and predict how various factors can affect the performance of a chemical compass from the unique perspective of quantum coherence assisted metrology. This represents a crucial step to affirm a direct connection between quantum coherence and the function of a chemical compass. PMID:24476240

  14. Development of a SQUID (Superconducting Quantum Interference Device) detection system of magnetic nanoparticles for cancer imaging

    NASA Astrophysics Data System (ADS)

    Ge, Song

    In this dissertation, I present the development of a SQUID (Superconducting Quantum Interference Device) imaging system using targeted magnetic nanoparticles (NPs) as contrast agents. The contrast agents are functionalized for targeting by the conjugation of the magnetic NPs to folic acid (FA) molecules on dendrimer scaffolds. Cellular internalization is accomplished through the high-affinity folic acid receptors (FARs), which are overexpressed in various human carcinomas. SQUID can be applied to detect signals from the magnetic cores of the contrast agents and hence diagnose the tumor. Based on the magnetic properties of the magnetic NPs, two detection methods were developed: remanence and magnetorelaxometry (MRX). The remanence measurement-based method detects magnetic NPs that are sufficiently large and possess long relaxation time. Samples were vertically oscillated and horizontally translated each in one-dimension. The system was calibrated with gamma-Fe2O3 NPs (mean diameter 25 nm) and the detection limit was found to be 10 ng at a distance of 1.7 cm and the spatial resolution was ˜1 cm. A theoretical model of this system was proposed and applied to image reconstruction of scanned phantoms with two NP injection spots. The developed SQUID system can determine not only the amount and horizontal position of the NPs, but also their depth in the phantoms. The MRX technique utilizes the NPs superparamagnetic property and records their time course magnetic decay. The system was investigated by using a number of iron oxide NP products with different mean diameters. The results showed that the MRX signal intensity is sensitively dependent on the size of the NPs. The best detection limit of 300 ng of total iron content was found on using a d = 12 nm Fe3O4 NP sample and this result was supported by computer simulations. To produce magnetic NPs for the MRX study, a synthetic approach of size-controllable Fe3O4 NPs was developed. Accordingly, the magnetic property can be

  15. Potential Applications of Microtesla Magnetic Resonance ImagingDetected Using a Superconducting Quantum Interference Device

    SciTech Connect

    Myers, Whittier R.

    2006-05-18

    This dissertation describes magnetic resonance imaging (MRI) of protons performed in a precession field of 132 {micro}T. In order to increase the signal-to-noise ratio (SNR), a pulsed 40-300 mT magnetic field prepolarizes the sample spins and an untuned second-order superconducting gradiometer coupled to a low transition temperature superconducting quantum interference device (SQUID) detects the subsequent 5.6-kHz spin precession. Imaging sequences including multiple echoes and partial Fourier reconstruction are developed. Calculating the SNR of prepolarized SQUID-detected MRI shows that three-dimensional Fourier imaging yields higher SNR than slice-selection imaging. An experimentally demonstrated field-cycling pulse sequence and post-processing algorithm mitigate image artifacts caused by concomitant gradients in low-field MRI. The magnetic field noise of SQUID untuned detection is compared to the noise of SQUID tuned detection, conventional Faraday detection, and the Nyquist noise generated by conducting biological samples. A second-generation microtesla MRI system employing a low-noise SQUID is constructed to increase SNR. A 2.4-m cubic, eddy-current shield with 6-mm thick aluminum walls encloses the experiment to attenuate external noise. The measured noise is 0.75 fT Hz{sup -1/2} referred to the bottom gradiometer loop. Solenoids wound from 30-strand braided wire to decrease Nyquist noise and cooled by either liquid nitrogen or water polarize the spins. Copper wire coils wound on wooden supports produce the imaging magnetic fields and field gradients. Water phantom images with 0.8 x 0.8 x 10 mm{sup 3} resolution have a SNR of 6. Three-dimensional 1.6 x 1.9 x 14 mm{sup 3} images of bell peppers and 3 x 3 x 26 mm{sup 3} in vivo images of the human arm are presented. Since contrast based on the transverse spin relaxation rate (T{sub 1}) is enhanced at low magnetic fields, microtesla MRI could potentially be used for tumor imaging. The measured T{sub 1} of ex

  16. Nanocrystal quantum dots as building blocks for artificial solids and their applications in optoelectronic devices

    NASA Astrophysics Data System (ADS)

    Choi, Joshua Jongwoo

    Nanocrystal quantum dots exhibit size-dependent optoelectronic properties and provide intriguing scientific and technological opportunities. Most proposed technologies based nanocrystals depend on macroscopic functional assemblies of nanocrystals in which the nanocrystals interact with each other to give rise to new collective properties - also called as artificial solids. As in the analogous atomic crystals, the optoelectronic properties of artificial solids are governed by (1) the energy levels of nanocrystals, (2) electronic coupling between nanocrystals, and (3) the symmetry of the nanocrystal superlattice. These issues add many levels of complexity to the design of artificial solids and, for the successful development of nanocrystal based technologies, it is crucial to gain deep understanding on the structure-property relationship of nanocrystals on multiple length scales. In this dissertation, I will present studies that show insights into the three governing factors of the optoelectronic properties of artificial solids mentioned above. (1) Nanocrystal energy levels: a direct correlation between interfacial energy level offsets between lead chalcogenide nanocrystals and ZnO layers with photovoltaic device performance is presented. Based on obtained insights on the size dependent photovoltaic properties of lead chalcogenide nanocrystals, first demonstration of solution processed nanocrystal tandem solar cells was achieved. (2) Inter-nanocrystal electronic coupling: rates of photogenerated exciton dissociation in nanocrystal assemblies as a function of inter-nanocrystal spacing are probed. The results show that excitons dissociate via tunneling induced delocalization among neighboring nanocrystals. Based on insights obtained from this work, drastically improved performance of solution processed nanocrystal infrared light emitting diodes is demonstrated. (3) Nanocrystal superlattice symmetry: interaction between ligand molecules on the surface of nanocrystals

  17. Spin filtering in a double quantum dot device: Numerical renormalization group study of the internal structure of the Kondo state

    SciTech Connect

    Vernek, E.; Büsser, C. A.; Anda, E. V.; Feiguin, A. E.; Martins, G. B.

    2014-03-31

    A double quantum dot device, connected to two channels that only interact through interdot Coulomb repulsion, is analyzed using the numerical renormalization group technique. Using a two-impurity Anderson model, and realistic parameter values [S. Amasha, A. J. Keller, I. G. Rau, A. Carmi, J. A. Katine, H. Shtrikman, Y. Oreg, and D. Goldhaber-Gordon, Phys. Rev. Lett. 110, 046604 (2013)], it is shown that, by applying a moderate magnetic field and independently adjusting the gate potential of each quantum dot at half-filling, a spin-orbital SU(2) Kondo state can be achieved where the Kondo resonance originates from spatially separated parts of the device. Our results clearly link this spatial separation effect to currents with opposing spin polarizations in each channel, i.e., the device acts as a spin filter. In addition, an experimental probe of this polarization effect is suggested, pointing to the exciting possibility of experimentally probing the internal structure of an SU(2) Kondo state.

  18. A Cs2LiYCl6:Ce-based advanced radiation monitoring device

    NASA Astrophysics Data System (ADS)

    Budden, B. S.; Stonehill, L. C.; Dallmann, N.; Baginski, M. J.; Best, D. J.; Smith, M. B.; Graham, S. A.; Dathy, C.; Frank, J. M.; McClish, M.

    2015-06-01

    Cs2LiYCl6:Ce3+ (CLYC) scintillator has gained recent interest because of its ability to perform simultaneous gamma spectroscopy and thermal neutron detection. Discrimination between the two incident particle types owes to the fundamentally unique emission waveforms, a consequence of the interaction and subsequent scintillation mechanisms within the crystal. Due to this dual-mode detector capability, CLYC was selected for the development of an Advanced Radiation Monitoring Device (ARMD), a compact handheld instrument for radioisotope identification and localization. ARMD consists of four 1 in.-right cylindrical CLYC crystals, custom readout electronics including a suitable multi-window application specific integrated circuit (ASIC), battery pack, proprietary software, and Android-based tablet for high-level analysis and display. We herein describe the motivation of the work and engineering design of the unit, and we explain the software embedded in the core module and for radioisotope analysis. We report an operational range of tens of keV to 8.5 MeV with approximately 5.3% gamma energy resolution at 662 keV, thermal neutron detection efficiency of 10%, battery lifetime of up to 10 h, manageable rates of 20 kHz; further, we describe in greater detail time to identify specific gamma source setups.

  19. Family-centred care during midface advancement with a rigid external device: what do families need?

    PubMed

    Bredero-Boelhouwer, H; Joosten, K F M; van Veen-van der Hoek, M; Mathijssen, I M J

    2013-08-01

    Midface advancement with distraction osteogenesis using the rigid external device (RED) is an effective but invasive treatment to correct the hypoplastic midface. This study draws up an inventory of the stressors, needs and coping strategies of families during this treatment, to determine the best conditions for family-centred care. Data were collected by reviewing the patients' files and administering semi-structured interviews. The data were analysed using the software program Atlas.ti and were re-analysed by an independent researcher. Parents and patients were interviewed separately. Fourteen families participated. Four patients had an absolute indication for surgery. All families were eager to have the patient's facial appearance improved. Nevertheless, despite psychological counselling, they experienced stress when confronted with the changed facial appearance. Another stressor was weight loss. Six patients were in a state of acute malnutrition and needed supplementary feeding. We conclude that the best conditions for family-centred care should be aligned to the different phases of treatment. Leading up to surgery it is important to screen families' expectations regarding aesthetic, functional and social outcomes and to assess their capacity to cope with the long treatment and effects of changed facial appearance. Peer contact and psychosocial training to increase self-esteem are tools to enhance co-operation and satisfaction. During the distraction and stabilisation phase, we advise the monitoring of nutritional intake and weight. During all phases of treatment easy accessibility to the team is recommended. PMID:23664572

  20. Advanced Aerodynamic Devices to Improve the Performance, Economics, Handling, and Safety of Heavy Vehicles

    SciTech Connect

    Robert J. Englar

    2001-05-14

    Research is being conducted at the Georgia Tech Research Institute (GTRI) to develop advanced aerodynamic devices to improve the performance, economics, stability, handling and safety of operation of Heavy Vehicles by using previously-developed and flight-tested pneumatic (blown) aircraft technology. Recent wind-tunnel investigations of a generic Heavy Vehicle model with blowing slots on both the leading and trailing edges of the trailer have been conducted under contract to the DOE Office of Heavy Vehicle Technologies. These experimental results show overall aerodynamic drag reductions on the Pneumatic Heavy Vehicle of 50% using only 1 psig blowing pressure in the plenums, and over 80% drag reductions if additional blowing air were available. Additionally, an increase in drag force for braking was confirmed by blowing different slots. Lift coefficient was increased for rolling resistance reduction by blowing only the top slot, while downforce was produced for traction increase by blowing only the bottom. Also, side force and yawing moment were generated on either side of the vehicle, and directional stability was restored by blowing the appropriate side slot. These experimental results and the predicted full-scale payoffs are presented in this paper, as is a discussion of additional applications to conventional commercial autos, buses, motor homes, and Sport Utility Vehicles.

  1. Top-emitting quantum dots light-emitting devices employing microcontact printing with electricfield-independent emission.

    PubMed

    Liu, Shihao; Liu, Wenbo; Ji, Wenyu; Yu, Jing; Zhang, Wei; Zhang, Letian; Xie, Wenfa

    2016-01-01

    Recent breakthroughs in quantum dot light-emitting devices (QD-LEDs) show their promise in the development of next-generation displays. However, the QD-LED with conventional ITO-based bottom emission structure is difficult to realize the high aperture ratio, electricfield-independent emission and flexible full-color displays. Hence, we demonstrate top-emitting QD-LEDs with dry microcontact printing quantum dot films. The top-emitting structure is proved to be able to accelerate the excitons radiative transition rate, then contributing to stable electroluminescent efficiency with a very low roll-off, and preventing spectra from shifting and broadening with the electric field increases. The results suggest potential routes towards creating high aperture ratio, wide color gamut, color-stable and flexible QD-LED displays. PMID:26932521

  2. Top-emitting quantum dots light-emitting devices employing microcontact printing with electricfield-independent emission

    NASA Astrophysics Data System (ADS)

    Liu, Shihao; Liu, Wenbo; Ji, Wenyu; Yu, Jing; Zhang, Wei; Zhang, Letian; Xie, Wenfa

    2016-03-01

    Recent breakthroughs in quantum dot light-emitting devices (QD-LEDs) show their promise in the development of next-generation displays. However, the QD-LED with conventional ITO-based bottom emission structure is difficult to realize the high aperture ratio, electricfield-independent emission and flexible full-color displays. Hence, we demonstrate top-emitting QD-LEDs with dry microcontact printing quantum dot films. The top-emitting structure is proved to be able to accelerate the excitons radiative transition rate, then contributing to stable electroluminescent efficiency with a very low roll-off, and preventing spectra from shifting and broadening with the electric field increases. The results suggest potential routes towards creating high aperture ratio, wide color gamut, color-stable and flexible QD-LED displays.

  3. Top-emitting quantum dots light-emitting devices employing microcontact printing with electricfield-independent emission

    PubMed Central

    Liu, Shihao; Liu, Wenbo; Ji, Wenyu; Yu, Jing; Zhang, Wei; Zhang, Letian; Xie, Wenfa

    2016-01-01

    Recent breakthroughs in quantum dot light-emitting devices (QD-LEDs) show their promise in the development of next-generation displays. However, the QD-LED with conventional ITO-based bottom emission structure is difficult to realize the high aperture ratio, electricfield-independent emission and flexible full-color displays. Hence, we demonstrate top-emitting QD-LEDs with dry microcontact printing quantum dot films. The top-emitting structure is proved to be able to accelerate the excitons radiative transition rate, then contributing to stable electroluminescent efficiency with a very low roll-off, and preventing spectra from shifting and broadening with the electric field increases. The results suggest potential routes towards creating high aperture ratio, wide color gamut, color-stable and flexible QD-LED displays. PMID:26932521

  4. Biophotonic logic devices based on quantum dots and temporally-staggered Förster energy transfer relays

    NASA Astrophysics Data System (ADS)

    Claussen, Jonathan C.; Algar, W. Russ; Hildebrandt, Niko; Susumu, Kimihiro; Ancona, Mario G.; Medintz, Igor L.

    2013-11-01

    Integrating photonic inputs/outputs into unimolecular logic devices can provide significantly increased functional complexity and the ability to expand the repertoire of available operations. Here, we build upon a system previously utilized for biosensing to assemble and prototype several increasingly sophisticated biophotonic logic devices that function based upon multistep Förster resonance energy transfer (FRET) relays. The core system combines a central semiconductor quantum dot (QD) nanoplatform with a long-lifetime Tb complex FRET donor and a near-IR organic fluorophore acceptor; the latter acts as two unique inputs for the QD-based device. The Tb complex allows for a form of temporal memory by providing unique access to a time-delayed modality as an alternate output which significantly increases the inherent computing options. Altering the device by controlling the configuration parameters with biologically based self-assembly provides input control while monitoring changes in emission output of all participants, in both a spectral and temporal-dependent manner, gives rise to two input, single output Boolean Logic operations including OR, AND, INHIBIT, XOR, NOR, NAND, along with the possibility of gate transitions. Incorporation of an enzymatic cleavage step provides for a set-reset function that can be implemented repeatedly with the same building blocks and is demonstrated with single input, single output YES and NOT gates. Potential applications for these devices are discussed in the context of their constituent parts and the richness of available signal.

  5. Low-brightness quantum radar

    NASA Astrophysics Data System (ADS)

    Lanzagorta, Marco

    2015-05-01

    One of the major scientific thrusts from recent years has been to try to harness quantum phenomena to dramatically increase the performance of a wide variety of classical information processing devices. These advances in quantum information science have had a considerable impact on the development of standoff sensors such as quantum radar. In this paper we analyze the theoretical performance of low-brightness quantum radar that uses entangled photon states. We use the detection error probability as a measure of sensing performance and the interception error probability as a measure of stealthiness. We compare the performance of quantum radar against a coherent light sensor (such as lidar) and classical radar. In particular, we restrict our analysis to the performance of low-brightness standoff sensors operating in a noisy environment. We show that, compared to the two classical standoff sensing devices, quantum radar is stealthier, more resilient to jamming, and more accurate for the detection of low reflectivity targets.

  6. Computer assisted design of poly-silicon gated enhancement-mode, lateral double quantum dot devices for quantum computing

    NASA Astrophysics Data System (ADS)

    Bishop, Nathaniel; Young, Ralph; Borras Pinilla, Carlos; Stalford, Harold; Nielsen, Erik; Muller, Richard; Rahman, Rajib; Tracy, Lisa; Wendt, Joel; Lilly, Michael; Carroll, Malcolm

    2012-02-01

    We discuss trade-offs of different double quantum dot and charge sensor lay-outs using computer assisted design (CAD). We use primarily a semi-classical model, augmented with a self-consistent configuration interaction method. Although CAD for quantum dots is difficult due to uncontrolled factors (e.g., disorder), different ideal designs can still be compared. Comparisons of simulation and measured dot characteristics, such as capacitance, show that CAD can agree well with experiment for relevant cases. CAD results comparing several different designs will be discussed including a comparison to measurement results from the same designs. Trade-offs between poly-silicon and metal gate lay-outs will also be discussed. This work was performed, in part, at the Center for Integrated Nanotechnologies, a U.S. DOE, Office of Basic Energy Sciences user facility. The work was supported by the Sandia National Laboratories Directed Research and Development Program. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  7. Reprint of : A computational approach to quantum noise in time-dependent nanoelectronic devices

    NASA Astrophysics Data System (ADS)

    Gaury, Benoit; Waintal, Xavier

    2016-08-01

    We derive simple expressions that relate the noise and correlation properties of a general time-dependent quantum conductor to the wave functions of the system. The formalism provides a practical route for numerical calculations of quantum noise in an externally driven system. We illustrate the approach with numerical calculations of the noise properties associated to a voltage pulse applied on a one-dimensional conductor. The methodology is however fully general and can be used for a large class of mesoscopic conductors.

  8. A computational approach to quantum noise in time-dependent nanoelectronic devices

    NASA Astrophysics Data System (ADS)

    Gaury, Benoit; Waintal, Xavier

    2016-01-01

    We derive simple expressions that relate the noise and correlation properties of a general time-dependent quantum conductor to the wave functions of the system. The formalism provides a practical route for numerical calculations of quantum noise in an externally driven system. We illustrate the approach with numerical calculations of the noise properties associated to a voltage pulse applied on a one-dimensional conductor. The methodology is however fully general and can be used for a large class of mesoscopic conductors.

  9. Ground-state modulation-enhancement by two-state lasing in quantum-dot laser devices

    SciTech Connect

    Röhm, André; Lingnau, Benjamin; Lüdge, Kathy

    2015-05-11

    We predict a significant increase of the 3 dB-cutoff-frequency on the ground-state lasing wavelength for two-state-lasing quantum-dot lasers using a microscopically motivated multi-level rate-equation model. After the onset of the second lasing line, the excited state acts as a high-pass filter, improving the ground-state response to faster modulation frequencies. We present both numerically simulated small-signal and large-signal modulation results and compare the performance of single and two-state lasing devices. Furthermore, we give dynamical arguments for the advantages of two-state lasing on data-transmission capabilities.

  10. A superconducting quantum interference device based read-out of a subattonewton force sensor operating at millikelvin temperatures

    SciTech Connect

    Usenko, O.; Vinante, A.; Wijts, G.; Oosterkamp, T. H.

    2011-03-28

    We present a scheme to measure the displacement of a nanomechanical resonator at cryogenic temperature. The technique is based on the use of a superconducting quantum interference device to detect the magnetic flux change induced by a magnetized particle attached on the end of the resonator. Unlike conventional interferometric techniques, our detection scheme does not involve direct power dissipation in the resonator, and therefore, is particularly suitable for ultralow temperature applications. We demonstrate its potential by cooling an ultrasoft silicon cantilever to a noise temperature of 25 mK, corresponding to a subattonewton thermal force noise of 0.5 aN/{radical}(Hz).

  11. High-Tc superconducting quantum interference device recordings of spontaneous brain activity: Towards high-Tc magnetoencephalography

    NASA Astrophysics Data System (ADS)

    Öisjöen, F.; Schneiderman, J. F.; Figueras, G. A.; Chukharkin, M. L.; Kalabukhov, A.; Hedström, A.; Elam, M.; Winkler, D.

    2012-03-01

    We have performed single- and two-channel high transition temperature (high-Tc) superconducting quantum interference device (SQUID) magnetoencephalography (MEG) recordings of spontaneous brain activity in two healthy human subjects. We demonstrate modulation of two well-known brain rhythms: the occipital alpha rhythm and the mu rhythm found in the motor cortex. We further show that despite higher noise-levels compared to their low-Tc counterparts, high-Tc SQUIDs can be used to detect and record physiologically relevant brain rhythms with comparable signal-to-noise ratios. These results indicate the utility of high-Tc technology in MEG recordings of a broader range of brain activity.

  12. An innovative epitaxial growth method for minimizing dislocations in thin-film quantum-dot optoelectronic and photovoltaic device applications

    NASA Astrophysics Data System (ADS)

    Gandhi, Jateen S.

    A new buffer layer method for epitaxial growth of lattice-mismatched semiconductor quantum-dots based p-i-n structures is presented. To our knowledge this is the first instance of a dislocation-reduction approach that has shown reduced dark current behavior in a quantum-dot device compared to its counterpart homojunction p-n device consisted of the barrier material. The present work compared a lattice misfit strain build-up behavior between an In0.15Ga0.85As (p) / InAs ( i) / In0.15Ga0.85As (n) (QD) device to an In0.15Ga0.85As (p) / In 0.15Ga0.85As (n) (HOM) device, as both were grown on an un-doped gallium arsenide (GaAs) (100) substrate. The intrinsic region of QD device incorporated 5 layers of 2.1 ML indium arsenide quantum dots that were fabricated using self-assembly via Stranski-Krastanov strain release mechanism. Atomic force microscopy measurements exhibited 35 +/- 3 nm sized pyramidal islands with a narrow distribution and a density of 2.5 x 1010 per cm2. A low temperature (6K) photoluminescence characterization of the QD sample revealed an activity at 1400 nm wavelength that was attributed to optical pumping of carriers, which experienced a 3-dimensional quantum confinement due to a potential well formed by In0.15Ga0.85As matrix, and their subsequent radiative recombination. Both of the QD and HOM samples were characterized using x-ray diffractometer (XRD) and a high resolution transmission electron microscopy (HRTEM) method. The XRD data recorded a signature of the biaxially strained pseudomorphic section of In0.15Ga0.85As buffer layer that absorbed a lattice misfit due to epitaxial growth on GaAs substrate. This signature consisted of a set of twin peaks at higher and lower 2theta degrees resembling elastically strained and plastically relaxed sections, respectively, of the buffer layer residing in the vicinity of buffer-GaAs interface. A comparison of those peaks between QD and HOM samples exhibited an increase in the volume of the plastically relaxed

  13. Novel Rigid External Distraction Device Improves Stability and Controls the Vector During Midfacial Advancement.

    PubMed

    Resnick, Cory M; Rottgers, Stephen Alex; Langenfeld, Christopher C; Mulliken, John B; Padwa, Bonnie L

    2016-06-01

    The major limitation of the rigid external devices currently used for midfacial distraction after subcranial Le Fort III osteotomies is the ductile wire that connects the midface to the device, which makes it difficult to control the vector and force during distraction. The authors describe a novel external appliance that addresses this and other problems of contemporary devices, and application of a custom cranial template that facilitates precise placement of the device to achieve the planned vector of distraction. PMID:27213737

  14. Advanced copper/low-k IC devices: Packaging process development and materials integrtion

    NASA Astrophysics Data System (ADS)

    Chungpaiboonpatana, Surasit

    Cu/low-k technology provides a number of key advantages including higher interconnect density, improved electrical performance, enhanced thermal performance, and reduced cost. Nevertheless, Cu/low-k IC technology poses many challenges to the packaging industry today. Specifically, low-k dielectric is much more fragile mechanically and copper surfaces are readily oxidized thereby weakening their adhesion to the ILD/metallization layers. The purpose of the study is to provide integrated and reliable materials and process solutions for the packaging of advanced Cu/low-k devices through fundamental materials science understanding. Novel solutions for advanced wirebond and flip-chip technologies are developed, along with resolutions for local and global material interaction issues. The zero-th packaging level study examines a novel direct gold wirebonding onto the Cu/low-k terminal pad structure. The first packaging level study attempts to eliminate the Cu/low-k wiresweeping issue through assembly material interactions with both bonding and transfer molding processes. The second packaging level study exams at the impact of Cu/low-k and processing material implementations on the copper trace cracking failures at the substrate level of a package. An integrated first and second level study on high performance flip chip technology using 8M Cu/low-k silicon chip is performed by the optimization of the underfill and substrate materials selections. Lastly, electromigration phenomena and corrosion mechanisms of copper metallization are developed for biased stressing assembly environment through the fundamental of electrochemistry. Throughout the experiment, the 90/130nm technology node of copper wafer fabrication using Black Diamond low-k dielectric is implemented in several large form-factor package assemblies. Functional test vehicles are assembled, reliability-stressed, and failure-analyzed according to the JEDEC standards for the validity of the integrated materials

  15. Automated hotspot analysis with aerial image CD metrology for advanced logic devices

    NASA Astrophysics Data System (ADS)

    Buttgereit, Ute; Trautzsch, Thomas; Kim, Min-ho; Seo, Jung-Uk; Yoon, Young-Keun; Han, Hak-Seung; Chung, Dong Hoon; Jeon, Chan-Uk; Meyers, Gary

    2014-09-01

    Continuously shrinking designs by further extension of 193nm technology lead to a much higher probability of hotspots especially for the manufacturing of advanced logic devices. The CD of these potential hotspots needs to be precisely controlled and measured on the mask. On top of that, the feature complexity increases due to high OPC load in the logic mask design which is an additional challenge for CD metrology. Therefore the hotspot measurements have been performed on WLCD from ZEISS, which provides the benefit of reduced complexity by measuring the CD in the aerial image and qualifying the printing relevant CD. This is especially of advantage for complex 2D feature measurements. Additionally, the data preparation for CD measurement becomes more critical due to the larger amount of CD measurements and the increasing feature diversity. For the data preparation this means to identify these hotspots and mark them automatically with the correct marker required to make the feature specific CD measurement successful. Currently available methods can address generic pattern but cannot deal with the pattern diversity of the hotspots. The paper will explore a method how to overcome those limitations and to enhance the time-to-result in the marking process dramatically. For the marking process the Synopsys WLCD Output Module was utilized, which is an interface between the CATS mask data prep software and the WLCD metrology tool. It translates the CATS marking directly into an executable WLCD measurement job including CD analysis. The paper will describe the utilized method and flow for the hotspot measurement. Additionally, the achieved results on hotspot measurements utilizing this method will be presented.

  16. ISS Squat and Deadlift Kinematics on the Advanced Resistive Exercise Device

    NASA Technical Reports Server (NTRS)

    Newby, N.; Caldwell, E.; Sibonga, J.; Ploutz-Snyder, L.

    2014-01-01

    Visual assessment of exercise form on the Advanced Resistive Exercise Device (ARED) on orbit is difficult due to the motion of the entire device on its Vibration Isolation System (VIS). The VIS allows for two degrees of device translational motion, and one degree of rotational motion. In order to minimize the forces that the VIS must damp in these planes of motion, the floor of the ARED moves as well during exercise to reduce changes in the center of mass of the system. To help trainers and other exercise personnel better assess squat and deadlift form a tool was developed that removes the VIS motion and creates a stick figure video of the exerciser. Another goal of the study was to determine whether any useful kinematic information could be obtained from just a single camera. Finally, the use of these data may aid in the interpretation of QCT hip structure data in response to ARED exercises performed in-flight. After obtaining informed consent, four International Space Station (ISS) crewmembers participated in this investigation. Exercise was videotaped using a single camera positioned to view the side of the crewmember during exercise on the ARED. One crewmember wore reflective tape on the toe, heel, ankle, knee, hip, and shoulder joints. This technique was not available for the other three crewmembers, so joint locations were assessed and digitized frame-by-frame by lab personnel. A custom Matlab program was used to assign two-dimensional coordinates to the joint locations throughout exercise. A second custom Matlab program was used to scale the data, calculate joint angles, estimate the foot center of pressure (COP), approximate normal and shear loads, and to create the VIS motion-corrected stick figure videos. Kinematics for the squat and deadlift vary considerably for the four crewmembers in this investigation. Some have very shallow knee and hip angles, and others have quite large ranges of motion at these joints. Joint angle analysis showed that crewmembers

  17. Prospects of application of superconducting electrodynamic structures in electronic devices for their advancement to the terahertz range

    NASA Astrophysics Data System (ADS)

    Kuraev, A. A.; Kurkin, S. A.; Koronovskii, A. A.; Rak, A. O.; Sinitsyn, A. K.; Hramov, A. E.

    2015-04-01

    It is shown that the application of superconducting electrodynamic structures in microwave electronic devices not only improves their characteristics, but also creates premises for implementation of devices like the autophase traveling-wave tube (TWT) and peniotron operating in the millimeter range with their further advancement to the terahertz range, which is impossible for conventional electrodynamic structures with Ohmic losses. Superconducting corrugated waveguides make it possible to suspend limitations imposed on the output power of pulsed relativistic Cherenkov oscillators, which are associated with thermal degradation of the working surface of conventional waveguides with Ohmic losses.

  18. Co thickness dependence of structural and magnetic properties in spin quantum cross devices utilizing stray magnetic fields

    SciTech Connect

    Kaiju, H. Kasa, H.; Mori, S.; Misawa, T.; Abe, T.; Nishii, J.; Komine, T.

    2015-05-07

    We investigate the Co thickness dependence of the structural and magnetic properties of Co thin-film electrodes sandwiched between borate glasses in spin quantum cross (SQC) devices that utilize stray magnetic fields. We also calculate the Co thickness dependence of the stray field between the two edges of Co thin-film electrodes in SQC devices using micromagnetic simulation. The surface roughness of Co thin films with a thickness of less than 20 nm on borate glasses is shown to be as small as 0.18 nm, at the same scanning scale as the Co film thickness, and the squareness of the hysteresis loop is shown to be as large as 0.96–1.0. As a result of the establishment of polishing techniques for Co thin-film electrodes sandwiched between borate glasses, we successfully demonstrate the formation of smooth Co edges and the generation of stray magnetic fields from Co edges. Theoretical calculation reveals that a strong stray field beyond 6 kOe is generated when the Co thickness is greater than 10 nm at a junction gap distance of 5 nm. From these experimental and calculation results, it can be concluded that SQC devices with a Co thickness of 10–20 nm can be expected to function as spin-filter devices.

  19. An improved scheme on decoy-state method for measurement-device-independent quantum key distribution.

    PubMed

    Wang, Dong; Li, Mo; Guo, Guang-Can; Wang, Qin

    2015-01-01

    Quantum key distribution involving decoy-states is a significant application of quantum information. By using three-intensity decoy-states of single-photon-added coherent sources, we propose a practically realizable scheme on quantum key distribution which approaches very closely the ideal asymptotic case of an infinite number of decoy-states. We make a comparative study between this scheme and two other existing ones, i.e., two-intensity decoy-states with single-photon-added coherent sources, and three-intensity decoy-states with weak coherent sources. Through numerical analysis, we demonstrate the advantages of our scheme in secure transmission distance and the final key generation rate. PMID:26463580

  20. Quantum Phase Coherence in Mesoscopic Transport Devices with Two-Particle Interaction.

    PubMed

    Wang, Zhimei; Guo, Xiaofang; Xue, Haibin; Xue, Naitao; Liang, J-Q

    2015-01-01

    In this paper we demonstrate a new type of quantum phase coherence (QPC), which is generated by the two-body interaction. This conclusion is based on quantum master equation analysis for the full counting statistics of electron transport through two parallel quantum-dots with antiparallel magnetic fluxes in order to eliminate the Aharonov-Bohm interference of either single-particle or non-interacting two-particle wave functions. The interacting two-particle QPC is realized by the flux-dependent oscillation of the zero-frequency cumulants including the shot noise and skewness with a characteristic period. The accurately quantized peaks of cumulant spectrum may have technical applications to probe the two-body Coulomb interaction. PMID:26255858