DOE Office of Scientific and Technical Information (OSTI.GOV)

PETERSEN SW

Airborne electromagnetic (AEM) surveys were flown during fiscal year (FY) 2008 within the 600 Area in an attempt to characterize the underlying subsurface and to aid in the closure and remediation design study goals for the 200-PO-1 Groundwater Operable Unit (OU). The rationale for using the AEM surveys was that airborne surveys can cover large areas rapidly at relatively low costs with minimal cultural impact, and observed geo-electrical anomalies could be correlated with important subsurface geologic and hydrogeologic features. Initial interpretation of the AEM surveys indicated a tenuous correlation with the underlying geology, from which several anomalous zones likely associatedmore » with channels/erosional features incised into the Ringold units were identified near the River Corridor. Preliminary modeling resulted in a slightly improved correlation but revealed that more information was required to constrain the modeling (SGW-39674, Airborne Electromagnetic Survey Report, 200-PO-1 Groundwater Operable Unit, 600 Area, Hanford Site). Both time-and frequency domain AEM surveys were collected with the densest coverage occurring adjacent to the Columbia River Corridor. Time domain surveys targeted deeper subsurface features (e.g., top-of-basalt) and were acquired using the HeliGEOTEM{reg_sign} system along north-south flight lines with a nominal 400 m (1,312 ft) spacing. The frequency domain RESOLVE system acquired electromagnetic (EM) data along tighter spaced (100 m [328 ft] and 200 m [656 ft]) north-south profiles in the eastern fifth of the 200-PO-1 Groundwater OU (immediately adjacent to the River Corridor). The overall goal of this study is to provide further quantification of the AEM survey results, using ground based geophysical methods, and to link results to the underlying geology and/or hydrogeology. Specific goals of this project are as follows: (1) Test ground based geophysical techniques for the efficacy in delineating underlying geology; (2) Use ground measurements to refine interpretations of AEM data; and (3) Improve the calibration and correlation of AEM information. The potential benefits of this project are as follows: (1) Develop a tool to map subsurface units at the Hanford Site in a rapid and cost effective manner; (2) Map groundwater pathways within the River Corridor; and (3) Aid development of the conceptual site model. If anomalies observed in the AEM data can be correlated with subsurface geology, then the rapid scanning and non-intrusive capabilities provided by the airborne surveys can be used at the Hanford Site to screen for areas that warrant further investigation.« less

Synthesis of P(AM-co-MAA)/AEM composite microspheres with lichi-like surface structure using porous microgel as template.

PubMed

Yang, Juxiang; Hu, Daodao; Xue, Min; Yang, Xing

2014-03-15

The P(AM-co-MAA)/AEM composite microspheres with lichi-like structure were synthesized by the hydrolysis and condensation of 3-(trimethoxysilyl)-propyldimethyloctadecyl-ammonium chloride (AEM) located within porous poly(acrylamide-co-methylacrylic acid) (P(AM-co-MAA)) microgels in an ammonia water atmosphere. The morphology and composition of the composite microspheres were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Fourier transform infrared spectrometer (FI-IR), and X-ray photoelectron spectroscopy (XPS), respectively. The results indicated that the composite microspheres with lichi-like surface structure could be obtained by controlling the loaded amount of AEM, the hydrolysis-condensation time of AEM, and the cross-linking degree of the porous P(AM-co-MAA) microgels. On the basis of the results, the mechanism on the formation of the microspheres with lichi-like surface structure was proposed. The multiple factors play a role in the formation of the specific surface morphology. The pores of the porous microgels make AEM behavior localized; the migration of AEM along with solvent evaporation leads to the structural change; the hydrolysis-condensation of AEM brings the temporarily structural solidification; the surface tension of hydrophobic AEM in hydrophilic atmosphere induces AEM liquid membrane constriction. Although the mechanism is complicated, the method is very simple. Based on the analogous principle, other composite materials with lichi-like structure could be constructed by altering precursor and porous template. Copyright © 2013 Elsevier Inc. All rights reserved.

Electrodialytic Transport Properties of Anion-Exchange Membranes Prepared from Poly(vinyl alcohol) and Poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride).

PubMed

Jikihara, Atsushi; Ohashi, Reina; Kakihana, Yuriko; Higa, Mitsuru; Kobayashi, Kenichi

2013-01-02

Random-type anion-exchange membranes (AEMs) have been prepared by blending poly(vinyl alcohol) (PVA) and the random copolymer-type polycation, poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride) at various molar percentages of anion-exchange groups to vinyl alcohol groups, Cpc, and by cross-linking the PVA chains with glutaraldehyde (GA) solution at various GA concentrations, CGA. The characteristics of the random-type AEMs were compared with blend-type AEMs prepared in our previous study. At equal molar percentages of the anion exchange groups, the water content of the random-type AEMs was lower than that of the blend-type AEMs. The effective charge density of the random-type AEMs increased with increasing Cpc and reached a maximum value. Further, the maximum value of the effective charge density increased with increasing CGA. The maximum value of the effective charge density, 0.42 mol/dm3, was obtained for the random-type AEM with Cpc = 4.2 mol % and CGA = 0.15 vol %. A comparison of the random-type and blend-type AEMs with almost the same Cpc showed that the random-type AEMs had lower membrane resistance than the blend-type ones. The membrane resistance and dynamic transport number of the random-type AEM with Cpc = 6.0 mol % and CGA = 0.15 vol % were 4.8 Ω cm2 and 0.83, respectively.

Electrodialytic Transport Properties of Anion-Exchange Membranes Prepared from Poly(vinyl alcohol) and Poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride)

PubMed Central

Jikihara, Atsushi; Ohashi, Reina; Kakihana, Yuriko; Higa, Mitsuru; Kobayashi, Kenichi

2012-01-01

Random-type anion-exchange membranes (AEMs) have been prepared by blending poly(vinyl alcohol) (PVA) and the random copolymer-type polycation, poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride) at various molar percentages of anion-exchange groups to vinyl alcohol groups, Cpc, and by cross-linking the PVA chains with glutaraldehyde (GA) solution at various GA concentrations, CGA. The characteristics of the random-type AEMs were compared with blend-type AEMs prepared in our previous study. At equal molar percentages of the anion exchange groups, the water content of the random-type AEMs was lower than that of the blend-type AEMs. The effective charge density of the random-type AEMs increased with increasing Cpc and reached a maximum value. Further, the maximum value of the effective charge density increased with increasing CGA. The maximum value of the effective charge density, 0.42 mol/dm3, was obtained for the random-type AEM with Cpc = 4.2 mol % and CGA = 0.15 vol %. A comparison of the random-type and blend-type AEMs with almost the same Cpc showed that the random-type AEMs had lower membrane resistance than the blend-type ones. The membrane resistance and dynamic transport number of the random-type AEM with Cpc = 6.0 mol % and CGA = 0.15 vol % were 4.8 Ω cm2 and 0.83, respectively. PMID:24958543

Quantitative magnetic resonance imaging analysis of the cross-sectional areas of the anconeus epitrochlearis muscle, cubital tunnel, and ulnar nerve with the elbow in extension in patients with and without ulnar neuropathy.

PubMed

Eng, Hing Y; Gunio, Drew A; Benitez, Carlos L

2018-05-10

The purpose of this study was to assess the cross-sectional area of the anconeus epitrochlearis muscle (AEM), cubital tunnel, and ulnar nerve with the elbow in extension in patients with and without ulnar neuropathy. We performed a retrospective, level IV review of elbow magnetic resonance imaging (MRI) studies. Elbow MRI studies of 32 patients with an AEM (26 men and 6 women, aged 18-60 years), 32 randomly selected patients without an AEM (aged 16-71 years), and 32 patients with clinical ulnar neuritis (22 men and 10 women, aged 24-76 years) were reviewed. We evaluated the ulnar nerve cross-sectional area proximal to, within, and distal to the cubital tunnel; AEM cross-sectional area; and cubital tunnel cross-sectional area. We found no significant difference in the nerve caliber between patients with and without an AEM. No correlation was found between the AEM cross-sectional area and ulnar nerve cross-sectional area within the cubital tunnel (r = 0.14). The mean cubital tunnel cross-sectional area was larger in patients with an AEM. Only 4 of the 32 patients with an AEM had findings of ulnar neuritis on MRI. Of the 32 patients with a clinical diagnosis of ulnar neuritis, only 2 had an AEM. With the elbow in extension, the presence or cross-sectional area of an AEM does not correlate with the area of the ulnar nerve or cubital tunnel. Only a small number of individuals with MRI evidence of an AEM had clinical evidence of ulnar neuropathy. Likewise, MRI evidence of an AEM was found in only a small number of individuals with clinical evidence of ulnar neuropathy. Copyright © 2018 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Quantifying Silica Reactivity in Subsurface Environments: Reaction Affinity and Solute Matrix Controls on Quartz and SiO2 Glass Dissolution Kinetics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patricia M. Dove

2000-12-13

During the three years of this project, Professor Dove's laboratory made tremendous progress in understanding controls on amorphous silica dissolution kinetics in aqueous solutions. Our findings have already received considerable attention. In hydrothermal and low temperature studies, the work focused on determining quantitative and mechanistic controls on the most abundant silica polymorphs in Earth environments--quartz and amorphous silica. Our studies achieved goals set forth in the original proposal to establish a new quantitative understanding of amorphous silica dissolution. This support has resulted in 10 journal, 12 abstracts and 2 thesis publications. The PI and students were also recognized with 6more » awards during this period. The 1998 EMSP conference in Chicago was an important meeting for our project. The symposium, enabled P.I. Dove to establish valuable contacts with ''users'' having specific needs for the findings of our EMSP project related to the urgency of problems in the Tanks Focus Area (TFA). Since that time, our working relations developed as Dove interacted with TFA scientists and engineers on the problems of waste glass properties. These interactions refined our experimental objectives to better meet their needs. Dove presented the results of EMSP research findings to a TFA subgroup at a Product Acceptance Workshop held in Salt Lake City during December 1998. The travel costs to attend this unanticipated opportunity were paid from EMSP project funds. In January 2000, Dove also attended a similar meeting in Atlanta with PNNL, SRL and BNF scientists/engineers to discuss new issues and make another level of decisions on the Product Acceptance goals. Our EMSP-funded research interfaced very well with the ongoing studies of Dr. Pete McGrail and colleagues in the Applied Geochemistry Group at PNNL. The value of our work to ''users'' was further demonstrated when Dove's EMSP-funded Postdoc, Dr. Jonathan Icenhower was hired by the same PNNL group. With the Icenhower move from postdoc in the Dove lab to a senior scientist position at PNNL, we directly facilitated information transfer from the ''university to user'' environment. Icenhower brought experience in silica-water reactivity and the experimental expertise in high-quality methods of mineral-water reaction kinetics to the PNNL waste clean-up effort. In a further interaction, M.S. student Troy Lorier was hired at the Savannah River Laboratory for a staff position with the Bill Holtzcheiter glass group. His research meshed well with on-going efforts at SRL. In short, our EMSP project went well beyond the academic goals of producing high quality scientific knowledge to establish connections with on-site users to solve problems in TFA. This project also produced new talent for the waste immobilization effort. This EMSP project was highly successful and we thank our sponsors for the opportunity to advance scientific knowledge in this important area of research.« less

Analysis of concrete beams using applied element method

NASA Astrophysics Data System (ADS)

Lincy Christy, D.; Madhavan Pillai, T. M.; Nagarajan, Praveen

2018-03-01

The Applied Element Method (AEM) is a displacement based method of structural analysis. Some of its features are similar to that of Finite Element Method (FEM). In AEM, the structure is analysed by dividing it into several elements similar to FEM. But, in AEM, elements are connected by springs instead of nodes as in the case of FEM. In this paper, background to AEM is discussed and necessary equations are derived. For illustrating the application of AEM, it has been used to analyse plain concrete beam of fixed support condition. The analysis is limited to the analysis of 2-dimensional structures. It was found that the number of springs has no much influence on the results. AEM could predict deflection and reactions with reasonable degree of accuracy.

Characterization of a broad-specificity non-haem iron N-demethylase from Pseudomonas putida CBB5 capable of utilizing several purine alkaloids as sole carbon and nitrogen source.

PubMed

Summers, Ryan M; Louie, Tai Man; Yu, Chi Li; Subramanian, Mani

2011-02-01

N-Demethylation of many xenobiotics and naturally occurring purine alkaloids such as caffeine and theobromine is primarily catalysed in higher organisms, ranging from fungi to mammals, by the well-studied membrane-associated cytochrome P450s. In contrast, there is no well-characterized enzyme for N-demethylation of purine alkaloids from bacteria, despite several reports on their utilization as sole source of carbon and nitrogen. Here, we provide what we believe to be the first detailed characterization of a purified N-demethylase from Pseudomonas putida CBB5. The soluble N-demethylase holoenzyme is composed of two components, a reductase component with cytochrome c reductase activity (Ccr) and a two-subunit N-demethylase component (Ndm). Ndm, with a native molecular mass of 240 kDa, is composed of NdmA (40 kDa) and NdmB (35 kDa). Ccr transfers reducing equivalents from NAD(P)H to Ndm, which catalyses an oxygen-dependent N-demethylation of methylxanthines to xanthine, formaldehyde and water. Paraxanthine and 7-methylxanthine were determined to be the best substrates, with apparent K(m) and k(cat) values of 50.4±6.8 μM and 16.2±0.6 min(-1), and 63.8±7.5 μM and 94.8±3.0 min(-1), respectively. Ndm also displayed activity towards caffeine, theobromine, theophylline and 3-methylxanthine, all of which are growth substrates for this organism. Ndm was deduced to be a Rieske [2Fe-2S]-domain-containing non-haem iron oxygenase based on (i) its distinct absorption spectrum and (ii) significant identity of the N-terminal sequences of NdmA and NdmB with the gene product of an uncharacterized caffeine demethylase in P. putida IF-3 and a hypothetical protein in Janthinobacterium sp. Marseille, both predicted to be Rieske non-haem iron oxygenases.

Performance of single chamber biocatalyzed electrolysis with different types of ion exchange membranes.

PubMed

Rozendal, René A; Hamelers, Hubertus V M; Molenkamp, Redmar J; Buisman, Cees J N

2007-05-01

In this paper hydrogen production through biocatalyzed electrolysis was studied for the first time in a single chamber configuration. Single chamber biocatalyzed electrolysis was tested in two configurations: (i) with a cation exchange membrane (CEM) and (ii) with an anion exchange membrane (AEM). Both configurations performed comparably and produced over 0.3 m3 H2/m3 reactor liquid volume/day at 1.0 V applied voltage (overall hydrogen efficiencies around 23%). Analysis of the water that permeated through the membrane revealed that a large part of potential losses in the system were associated with a pH gradient across the membrane (CEM DeltapH=6.4; AEM DeltapH=4.4). These pH gradient associated potential losses were lower in the AEM configuration (CEM 0.38 V; AEM 0.26 V) as a result of its alternative ion transport properties. This benefit of the AEM, however, was counteracted by the higher cathode overpotentials occurring in the AEM configuration (CEM 0.12 V at 2.39 A/m2; AEM 0.27 V at 2.15 A/m2) as a result of a less effective electroless plating method for the AEM membrane electrode assembly (MEA).

Modification and properties characterization of heterogeneous anion-exchange membranes by electrodeposition of graphene oxide (GO)

NASA Astrophysics Data System (ADS)

Li, Yujiao; Shi, Shaoyuan; Cao, Hongbin; Zhao, Zhijuan; Wen, Hao

2018-06-01

The heterogeneous anion exchange membranes (AEMs) were modified by electrodeposition of graphene oxide (GO) under different conditions. The physicochemical properties of GO-modified membranes were characterized systemically to obtain the optimized conditions for the electrodeposition of GO on the surface of AEMs. The results indicated that the contact angle and zeta potential of the modified AEMs decreased when increasing the concentration of GO from 0.05 g/L to 0.1 g/L. The higher concentration of NaCl, as the supporting electrolyte, could hinder the electrodeposition of GO on the AEMs for the competitive migration between the GO and Cl- ions. The increase of current density had a positive effect on properties of GO-modified membranes in the range of 1-5 mA/cm2. Compared with the pristine AEM, all the GO-modified AEMs exhibited smoother surface, higher hydrophilicity and negative zeta potential. It was also found that the GO modifying layer did not increase electrical resistance and had only a negligible effect on the desalination performance of AEMs. In the fouling experiments with sodium dodecyl benzene sulfonate (SDBS) as the model foulant, the GO-modified AEMs exhibited improved fouling resistance to SDBS.

Large Diameter Shuttle Launched-AEM (LDSL-AEM) study

NASA Technical Reports Server (NTRS)

1976-01-01

A technical description of a Large Diameter Shuttle Launched-AEM (LDSL-AEM), an AEM base module adapted to carry 5 ft diameter payloads in the shuttle with propulsion for carrying payloads to higher altitude orbits from a 150 NM shuttle orbit, is described. The AEM is designed for launch on the scout launch vehicle. Onboard equipment provides capability to despin, acquire the earth, and control the vehicle in an earth pointing mode using reaction wheels for torque with magnets for all attitude acquisition, wheel desaturation, and nutation damping. Earth sensors in the wheels provide pitch and roll attitude. This system provides autonomous control capability to 1 degree in pitch and roll and 2 degrees in yaw. The attitude can be determined to .5 degrees in pitch and roll and 2 degrees in yaw.

A 14-year-old girl with tuberculous otitis media and brain abscess.

PubMed

Oberdorfer, Peninnah; Kongthavonsakul, Kritsana; Intachumpoo, Jintana; Odell, Shaun

2012-07-24

Tuberculosis is a rare cause of chronic suppurative otitis media and mastoiditis. Intracranial complications are rare. The authors report a case of a 14-year-old girl with chronic otitis media of her right ear for 2 years. Her presentation was as follows: 10 days before admission she had a high fever, headache, alteration of consciousness and a generalised seizure. CT scanning of her brain showed right otomastoiditis with early brain abscess of the right cerebellum. She underwent right radical mastoidectomy and aspiration of the cerebellar abscess. The pus from the mastoid and cerebellar abscess was stained positive for acid-fast bacilli (AFB). The pus culture grew Mycobacterium tuberculosis (MTB). Her discharge diagnosis was tuberculous mastoiditis (TM) with cerebellar abscess. Long-term treatment plans included antituberculous drugs for 1 year.

Analytical electron microscopy in mineralogy; exsolved phases in pyroxenes

USGS Publications Warehouse

Nord, G.L.

1982-01-01

Analytical scanning transmission electron microscopy has been successfully used to characterize the structure and composition of lamellar exsolution products in pyroxenes. At operating voltages of 100 and 200 keV, microanalytical techniques of x-ray energy analysis, convergent-beam electron diffraction, and lattice imaging have been used to chemically and structurally characterize exsolution lamellae only a few unit cells wide. Quantitative X-ray energy analysis using ratios of peak intensities has been adopted for the U.S. Geological Survey AEM in order to study the compositions of exsolved phases and changes in compositional profiles as a function of time and temperature. The quantitative analysis procedure involves 1) removal of instrument-induced background, 2) reduction of contamination, and 3) measurement of correction factors obtained from a wide range of standard compositions. The peak-ratio technique requires that the specimen thickness at the point of analysis be thin enough to make absorption corrections unnecessary (i.e., to satisfy the "thin-foil criteria"). In pyroxenes, the calculated "maximum thicknesses" range from 130 to 1400 nm for the ratios Mg/Si, Fe/Si, and Ca/Si; these "maximum thicknesses" have been contoured in pyroxene composition space as a guide during analysis. Analytical spatial resolutions of 50-100 nm have been achieved in AEM at 200 keV from the composition-profile studies, and analytical reproducibility in AEM from homogeneous pyroxene standards is ?? 1.5 mol% endmember. ?? 1982.

3D airborne EM modeling based on the spectral-element time-domain (SETD) method

NASA Astrophysics Data System (ADS)

Cao, X.; Yin, C.; Huang, X.; Liu, Y.; Zhang, B., Sr.; Cai, J.; Liu, L.

2017-12-01

In the field of 3D airborne electromagnetic (AEM) modeling, both finite-difference time-domain (FDTD) method and finite-element time-domain (FETD) method have limitations that FDTD method depends too much on the grids and time steps, while FETD requires large number of grids for complex structures. We propose a time-domain spectral-element (SETD) method based on GLL interpolation basis functions for spatial discretization and Backward Euler (BE) technique for time discretization. The spectral-element method is based on a weighted residual technique with polynomials as vector basis functions. It can contribute to an accurate result by increasing the order of polynomials and suppressing spurious solution. BE method is a stable tine discretization technique that has no limitation on time steps and can guarantee a higher accuracy during the iteration process. To minimize the non-zero number of sparse matrix and obtain a diagonal mass matrix, we apply the reduced order integral technique. A direct solver with its speed independent of the condition number is adopted for quickly solving the large-scale sparse linear equations system. To check the accuracy of our SETD algorithm, we compare our results with semi-analytical solutions for a three-layered earth model within the time lapse 10-6-10-2s for different physical meshes and SE orders. The results show that the relative errors for magnetic field B and magnetic induction are both around 3-5%. Further we calculate AEM responses for an AEM system over a 3D earth model in Figure 1. From numerical experiments for both 1D and 3D model, we draw the conclusions that: 1) SETD can deliver an accurate results for both dB/dt and B; 2) increasing SE order improves the modeling accuracy for early to middle time channels when the EM field diffuses fast so the high-order SE can model the detailed variation; 3) at very late time channels, increasing SE order has little improvement on modeling accuracy, but the time interval plays important roles. This research is supported by Key Program of National Natural Science Foundation of China (41530320), China Natural Science Foundation for Young Scientists (41404093), and Key National Research Project of China (2016YFC0303100, 2017YFC0601900). Figure 1: (a) AEM system over a 3D earth model; (b) magnetic field Bz; (c) magnetic induction dBz/dt.

Modeling Heat-Transfer in Animal Habitats in the Shuttle Orbiter Middeck

NASA Technical Reports Server (NTRS)

Eodice, Michael T.; Sun, Sid (Technical Monitor)

2000-01-01

A mathematical model has been developed to evaluate the heat transfer characteristics of an Animal Enclosure Module (AEM) in the microgravity environment. The AEM is a spaceflight habitat that provides life support for up to six rodents in the Space Shuttle Middeck. Currently, temperatures within the AEM are recorded in real time using a solid state data recorder; however, the data are only available for analysis post-flight. This temperature information is useful for characterizing the thermal environment of the AEM for researchers, but is unavailable during flight operations. Because animal health in microgravity is directly linked to the thermal environment, the ability to predict internal AEM temperatures is extremely useful to life science researchers. NASA flight crews typically carry hand-held temperature measurement devices which allow them to provide ground researchers with near real time readings of AEM inlet temperature; however, higher priority operations limit the frequency at which these measurements can be made and subsequently downlinked. The mathematical model developed allows users to predict internal cage volume temperatures based on knowledge of the ambient air temperature entering the AEM air intake ports. Additionally, an average convective heat transfer coefficient for the AEM has been determined to provide engineers with the requisite information to facilitate future design improvements and product upgrades. The model has been validated using empirical data from a series of three Space Shuttle missions.

Imidazolium-based anion exchange membranes for alkaline anion fuel cells: elucidation of the morphology and the interplay between the morphology and properties.

PubMed

Zhao, Yue; Yoshimura, Kimio; Shishitani, Hideyuki; Yamaguchi, Susumu; Tanaka, Hirohisa; Koizumi, Satoshi; Szekely, Noemi; Radulescu, Aurel; Richter, Dieter; Maekawa, Yasunari

2016-02-07

We investigated the morphology and swelling behavior of a new graft-type of anion exchange membrane (AEM) containing 2-methylimidazolium groups by using a contrast variation small angle neutron scattering (SANS) technique. These AEMs were prepared by radiation-induced grafting of 2-methyl-1-vinylimidazole and styrene into poly(ethylene-co-tetrafluoroethylene) (ETFE) films and subsequent N-alkylation with methyliodide, and possessed both high alkaline durability and high conductivity. Our results showed that the crystalline lamellar and crystallite structures originating from the pristine ETFE films were more or less conserved in these AEMs, but the lamellar d-spacing in both dry and wet membranes was enlarged, indicating an expansion of the amorphous lamellae due to the graft chains introduced in the grafting process and the water incorporated in the swelling process. For the first time, the swelling behavior of the AEMs was studied quantitatively in various water mixtures of water and deuterated water with different volume ratios (contrast variation method), and the morphology of these membranes was elucidated by three phases: phase (1) crystalline ETFE domains, which offer good mechanical properties; phase (2) hydrophobic amorphous domains, which are made up of amorphous ETFE chains and offer a matrix to create conducting regions; phase (3) interconnected hydrated domains, which are composed of the entire graft chains and water and play a key role in promoting the conductivity.

A multi-scale permafrost investigation along the Alaska Highway Corridor based on airborne electromagnetic and auxiliary geophysical data

NASA Astrophysics Data System (ADS)

Minsley, B. J.; Kass, M. A.; Bloss, B.; Pastick, N.; Panda, S. K.; Smith, B. D.; Abraham, J. D.; Burns, L. E.

2012-12-01

More than 8000 square kilometers of airborne electromagnetic (AEM) data were acquired along the Alaska Highway Corridor in 2005-2006 by the Alaska Department of Natural Resources Division of Geological and Geophysical Surveys. Because this large AEM dataset covers diverse geologic and permafrost settings, it is an excellent testbed for studying the electrical geophysical response from a wide range of subsurface conditions. These data have been used in several recent investigations of geology, permafrost, and infrastructure along the highway corridor. In this study, we build on existing interpretations of permafrost features by re-inverting the AEM data using traditional least squares inversion techniques as well as recently developed stochastic methods aimed at quantifying uncertainty in geophysical data. Ground-based geophysical measurements, including time-domain electromagnetic soundings, surface nuclear magnetic resonance soundings, and shallow frequency-domain electromagnetic profiles, have also been acquired to help validate and extend the AEM interpretations. Here, we focus on the integration of different types of data to yield an improved characterization of permafrost, including: methods to discriminate between geologic and thermal controls on resistivity; identifying relationships between shallow resistivity and active layer thickness by incorporating auxiliary remote sensing data and ground-based measurements; quantifying apparent slope-aspect-resistivity relationships, where south-facing slopes appear less resistive than north-facing slopes within similar geologic settings; and investigating an observed decrease in resistivity beneath several areas associated with recent fires.

Understanding ion and solvent transport in anion exchange membranes under humidified conditions

NASA Astrophysics Data System (ADS)

Sarode, Himanshu

Anion exchange membranes (AEM) have been studied for more than a decade for potential applications in low temperature fuel cells and other electrochemical devices. They offer the advantage of faster reaction kinetics under alkaline conditions and ability to perform without costly platinum catalyst. Inherently slow diffusion of hydroxide ions compared to protons is a primary reason for synthesizing and studying the ion transport properties in AEMs. The aim of this thesis is to understand ion transport in novel AEMs using Pulse Gradient stimulated Spin Echo Nuclear Magnetic Resonance technique (PGSE NMR), water uptake, ionic conductivity, Small Angle X-ray Scattering (SAXS) etc. All experiments were performed under humidified conditions (80--95% relative humidity) and fuel cell operating temperatures of 30--90°C. In this work, the NMR tube design was modified for humidifying the entire NMR tube evenly from our previous design. We have developed a new protocol for replacing caustic hydroxide with harmless fluoride or bicarbonate ions for 19F and 13 C NMR diffusion experiments. After performing these NMR experiments, we have obtained in-depth understanding of the morphology linked ion transport in AEMs. We have obtained the highest fluoride self-diffusion coefficient of > 1 x 10-5 cm2/sec ( 55°C) for ETFE-g-PVBTMA membrane which is a result of low tortuosity of 1 obtained for the membrane. This faster fluoride transport combined with low tortuosity of the membrane resulted in > 100mS/cm hydroxide conductivity for the membrane. Polycyclooctene (PCOE) based triblock copolymers are also studied for in-depth understanding of molecular weight, IEC, mechanical and transport properties. Effect of melting temperature of PCOE has favorable effect on increasing ion conductivity and lowering activation energy. Mechanical properties of these types of membranes were studied showing detrimental effect of water plasticization which results in unsuitable mechanical properties. Hydroxide conductivity was studied to measure the effectiveness of AEMs for practical applications. PPO-b-PVBTMA membrane showed more than 100mS/cm conductivity and PCOE based membranes showed ~ 70mS/cm conductivity which is a combined effect of Grotthuss hopping and vehicular mode of ion transport, which lowers the activation energy to < 14 kJ/mol. Overall this thesis sheds light on one of the most important aspect of AEMs: ion/solvent transport, we have studied effect of membrane chemistry, IEC, morphology, polymer molecular weight on self-diffusion, ionic conductivity to have a better understanding for development of a good AEM for practical applications.

Anhydroecgonine methyl ester, a cocaine pyrolysis product, may contribute to cocaine behavioral sensitization.

PubMed

Garcia, Raphael Caio Tamborelli; Torres, Larissa Helena; Balestrin, Natália Trigo; Andrioli, Tatiana Costa; Flório, Jorge Camilo; de Oliveira, Carolina Dizioli Rodrigues; da Costa, José Luiz; Yonamine, Mauricio; Sandoval, Maria Regina Lopes; Camarini, Rosana; Marcourakis, Tania

2017-02-01

Crack cocaine has a high potential to induce cocaine addiction and its smoke contains cocaine's pyrolysis product anhydroecgonine methyl ester (AEME), a partial agonist at M 1 - and M 3 -muscarinic acetylcholine receptor and an antagonist at the remaining subtypes. No reports have assessed AEME's role in addiction. Adult male Wistar rats were intraperitoneally administered with saline, 3mg/kg AEME, 15mg/kg cocaine, or a cocaine-AEME combination on every other day during a period of 9 days. After a 7-days withdrawal period, a challenge injection of the respective drugs was performed on the 17th day. The locomotor activity was evaluated on days 1, 3, 5, 7, 9 and 17, as well as dopamine levels (9th day) and dopaminergic receptors proteins (D 1 R and D 2 R on the 17th day) in the caudate-putamen (CPu) and nucleus accumbens (NAc). AEME was not able to induce the expression of behavioral sensitization, but it substantially potentiates cocaine-effects, with cocaine-AEME combination presenting higher expression than cocaine alone. An increase in the dopamine levels in the CPu in all non-saline groups was observed, with the highest levels in the cocaine-AEME group. There was a decrease in D 1 R protein level in this brain region only for cocaine and cocaine-AEME groups. In the NAc, an increase in the dopamine levels was only observed for cocaine and cocaine-AEME groups, with no changes in both D 1 R and D 2 R protein levels. These behavioral and neurochemical data indicate that AEME alone does not elicit behavioral sensitization but it significantly potentiates cocaine effects when co-administered, resulting in dopamine increase in CPu and NAc, brain regions where dopamine release is mediated by cholinergic activity. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

From Divergent Lifestyles to Professional Issues: Fifteen Years with a University Sexuality Course.

ERIC Educational Resources Information Center

Moy, Caryl T.

1987-01-01

Describes a college course on human sexuality, its goals and evolution. Includes a section on student enrollment, student reasons for taking the course, and a discussion of goals and techniques for human sexuality instruction. (Author/AEM)

Targeting the impact of agri-environmental policy - Future scenarios in two less favoured areas in Portugal.

PubMed

Jones, Nadia; Fleskens, Luuk; Stroosnijder, Leo

2016-10-01

Targeting agri-environmental measures (AEM) improves their effectiveness in the delivery of public goods, provided the necessary coordination with other incentives. In less favoured areas (LFA) measures focusing on the conservation of extensive farming contribute to sustainable land management in these areas. In this paper we investigate the implementation of a possible AEM supporting the improvement of permanent pastures coordinated with the extensive livestock and single farm payments actually in place. Through applying a spatially-explicit mixed integer optimisation model we simulate future land use scenarios for two less favoured areas in Portugal (Centro and Alentejo) considering two policy scenarios: a 'targeted AEM', and a 'non-targeted AEM'. We then compare the results with a 'basic policy' option (reflecting a situation without AEM). This is done with regard to landscape-scale effects on the reduction of fire hazard and erosion risk, as well as effects on farm income. The results show that an AEM for permanent pastures would be more cost-effective for erosion and fire hazard mitigation if implemented within a spatially targeted framework. However when cost-effectiveness is assessed with other indicators (e.g. net farm income and share of grazing livestock) 'non-targeted AEM' implementation delivers the best outcome in Alentejo. In Centro the implementation of an AEM involves important losses of income compared to the 'basic policy'. 'Targeted AEM' tends to favour farms in very marginal conditions, i.e. targeting is demonstrated to perform best in landscapes where spatial heterogeneity is higher. The results also show the risk of farm abandonment in the two studied less favoured areas: in all three scenarios more than 30% of arable land is deemed to be abandoned. Copyright © 2016 Elsevier Ltd. All rights reserved.

Applications Explorer Missions (AEM): Mission planners handbook

NASA Technical Reports Server (NTRS)

Smith, S. R. (Editor)

1974-01-01

The Applications Explorer Missions (AEM) Program is a planned series of space applications missions whose purpose is to perform various tasks that require a low cost, quick reaction, small spacecraft in a dedicated orbit. The Heat Capacity Mapping Mission (HCMM) is the first mission of this series. The spacecraft described in this document was conceived to support a variety of applications instruments and the HCMM instrument in particular. The maximum use of commonality has been achieved. That is, all of the subsystems employed are taken directly or modified from other programs such as IUE, IMP, RAE, and Nimbus. The result is a small versatile spacecraft. The purpose of this document, the AEM Mission Planners Handbook (AEM/MPH) is to describe the spacecraft and its capabilities in general and the HCMM in particular. This document will also serve as a guide for potential users as to the capabilities of the AEM spacecraft and its achievable orbits. It should enable each potential user to determine the suitability of the AEM concept to his mission.

Investigation of performance and durability of polymer electrolytes for electrochemical energy storage and conversion technologies

NASA Astrophysics Data System (ADS)

Jung, Min-Suk

Polymeric ion exchange membranes are integral components of electrochemical conversion/storage devices such as fuel cells, water electrolyzers, and redox flow batteries. There has been dramatic progress in the research and development of cation exchange membranes (CEM). NafionRTM (perfluorosulfonic acid membranes) is one example of a state-of-the-art CEM and has been successfully demonstrated in various electrochemical energy devices. Unlike CEMs, anion exchange membranes (AEMs) have been of limited utility to date due to their drawbacks, including poor chemical/mechanical stability and low ionic conductivity. However, alkaline environments result in better activity for electrochemical reactions and afford the possibility of using non-platinum group metal (PGM) electrocatalysts. AEMs, therefore, are still being studied in order to resolve existing challenges in terms of conductivity and stability in alkaline media and in strongly oxidizing solutions. In this work, AEMs derived from different types of polymer backbones were prepared, and their chemical stability and electrochemical property were investigated. Polysulfone (PSF) AEMs were prepared by first chloromethylating polysulfone, then by functionalizing chloromethylated polysulfone (CMPSF) with different base reagents. PSF-trimethylamine (TMA) AEMs showed a 40-fold reduction in vanadium (IV) ion (VO2+) permeability when compared to a NafionRTM membrane and exceptional oxidative stability after exposure to a 1.5 M vanadium (V) ion (VO2+) solution for 90 days. PSF-TMA AEMs were successfully demonstrated in the all-vanadium redox flow battery. Excellent energy efficiencies (>75 %) were attained and sustained over 75 charge-discharge cycles for a vanadium redox flow battery prepared using the PSF-TMA separator. Crosslinking of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) AEMs using diamine was tried with intentions to improve the mechanical stability and electrochemical property of PPO AEM. Crosslinked PPO AEMs (30 +/- 4 % at 25 °C) showed less liquid water uptake than non-crosslinked PPO AEMs (46 +/- 5% at 25 °C) while maintaining comparable ionic conductivities (hydroxide ion conductivity of 45 mS/cm at 60 °C). Crosslinked PPO AEMs maintained mechanical integrity and still showed some mechanical stability (ultimate tensile strength of 3˜4 MPa and elongation at break of 13˜17 %) after exposure to 1 M KOH at 60 °C for 14 days, while non-crosslinked PPO AEMs completely lost their mechanical durability. Finally, this dissertation presents research related to perfluorinated AEMs prepared using a Grignard reagent. These membranes exhibited 0.7 mmol/g of Cl- ion exchange capacity (IEC), 20 mS/cm of hydroxide ion conductivity at 20 °C, and 10 % of water uptake at room temperature. The membranes also maintained 90 % of their initial conductivity after an exposure to 1.5 M VO2+ in 3 M H2SO4 solution for seven days.

Hydroxide Solvation and Transport in Anion Exchange Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Chen; Tse, Ying-Lung Steve; Lindberg, Gerrick E.

Understanding hydroxide solvation and transport in anion exchange membranes (AEMs) can provide important insight into the design principles of these new membranes. To accurately model hydroxide solvation and transport, we developed a new multiscale reactive molecular dynamics model for hydroxide in aqueous solution, which was then subsequently modified for an AEM material. With this model, we investigated the hydroxide solvation structure and transport mechanism in the membrane. We found that a relatively even separation of the rigid side chains produces a continuous overlapping region for hydroxide transport that is made up of the first hydration shell of the tethered cationicmore » groups. Our results show that hydroxide has a significant preference for this overlapping region, transporting through it and between the AEM side chains with substantial contributions from both vehicular (standard diffusion) and Grotthuss (proton hopping) mechanisms. Comparison of the AEM with common proton exchange membranes (PEMs) showed that the excess charge is less delocalized in the AEM than the PEMs, which is correlated with a higher free energy barrier for proton transfer reactions. The vehicular mechanism also contributes considerably more than the Grotthuss mechanism for hydroxide transport in the AEM, while our previous studies of PEM systems showed a larger contribution from the Grotthuss mechanism than the vehicular mechanism for proton transport. The activation energy barrier for hydroxide diffusion in the AEM is greater than that for proton diffusion in PEMs, implying a more significant enhancement of ion transport in the AEM at elevated temperatures.« less

Experimental and analytical study of secondary path variations in active engine mounts

NASA Astrophysics Data System (ADS)

Hausberg, Fabian; Scheiblegger, Christian; Pfeffer, Peter; Plöchl, Manfred; Hecker, Simon; Rupp, Markus

2015-03-01

Active engine mounts (AEMs) provide an effective solution to further improve the acoustic and vibrational comfort of passenger cars. Typically, adaptive feedforward control algorithms, e.g., the filtered-x-least-mean-squares (FxLMS) algorithm, are applied to cancel disturbing engine vibrations. These algorithms require an accurate estimate of the AEM active dynamic characteristics, also known as the secondary path, in order to guarantee control performance and stability. This paper focuses on the experimental and theoretical study of secondary path variations in AEMs. The impact of three major influences, namely nonlinearity, change of preload and component temperature, on the AEM active dynamic characteristics is experimentally analyzed. The obtained test results are theoretically investigated with a linear AEM model which incorporates an appropriate description for elastomeric components. A special experimental set-up extends the model validation of the active dynamic characteristics to higher frequencies up to 400 Hz. The theoretical and experimental results show that significant secondary path variations are merely observed in the frequency range of the AEM actuator's resonance frequency. These variations mainly result from the change of the component temperature. As the stability of the algorithm is primarily affected by the actuator's resonance frequency, the findings of this paper facilitate the design of AEMs with simpler adaptive feedforward algorithms. From a practical point of view it may further be concluded that algorithmic countermeasures against instability are only necessary in the frequency range of the AEM actuator's resonance frequency.

Hydroxide Solvation and Transport in Anion Exchange Membranes.

PubMed

Chen, Chen; Tse, Ying-Lung Steve; Lindberg, Gerrick E; Knight, Chris; Voth, Gregory A

2016-01-27

Understanding hydroxide solvation and transport in anion exchange membranes (AEMs) can provide important insight into the design principles of these new membranes. To accurately model hydroxide solvation and transport, we developed a new multiscale reactive molecular dynamics model for hydroxide in aqueous solution, which was then subsequently modified for an AEM material. With this model, we investigated the hydroxide solvation structure and transport mechanism in the membrane. We found that a relatively even separation of the rigid side chains produces a continuous overlapping region for hydroxide transport that is made up of the first hydration shell of the tethered cationic groups. Our results show that hydroxide has a significant preference for this overlapping region, transporting through it and between the AEM side chains with substantial contributions from both vehicular (standard diffusion) and Grotthuss (proton hopping) mechanisms. Comparison of the AEM with common proton exchange membranes (PEMs) showed that the excess charge is less delocalized in the AEM than the PEMs, which is correlated with a higher free energy barrier for proton transfer reactions. The vehicular mechanism also contributes considerably more than the Grotthuss mechanism for hydroxide transport in the AEM, while our previous studies of PEM systems showed a larger contribution from the Grotthuss mechanism than the vehicular mechanism for proton transport. The activation energy barrier for hydroxide diffusion in the AEM is greater than that for proton diffusion in PEMs, implying a more significant enhancement of ion transport in the AEM at elevated temperatures.

The number of past manic episodes is the best predictor of antidepressant-emergent manic switch in a cohort of bipolar depressed patients.

PubMed

Gorwood, Philip; Richard-Devantoy, Stéphane; Sentissi, Othman; Le Strat, Yann; Olié, Jean Pierre

2016-06-30

The present study sought to identify factors associated with the onset of a manic or hypomanic episode during the month following a new antidepressant therapy in depressed bipolar patients. Patients receiving mood stabilizers for ≥3 months were screened from 400 French centers and were assessed for a 4-week period following prescription of a first or a new antidepressant. Of the 1242 included participants, 4.8% (n=60) experienced antidepressant-emergent manic switch (AEMS). AEMS was more frequently associated with lifetime manic, depressive, and total mood episodes, and with past AEMS. A higher score at two items of the Montgomery-Åsberg Depression Rating Scale (pessimistic and suicidal thoughts) were significantly associated with AEMS. Logistic regression analysis showed that the number of lifetime manic episodes and past AEMS were the two most factors associated with an AEMS. Having more than four past manic episodes was associated with a 2.84 fold increased risk of AEMS. Cumulative number of past mood episodes seems to be the most important factor for switching to a manic episode following antidepressants in patients with bipolar disorder. Longer-term studies are required to further delineate antidepressant causality from natural disease course. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Effects of Cationic Pendant Groups on Ionic Conductivity for Anion Exchange Membranes: Structure Conductivity Relationships

NASA Astrophysics Data System (ADS)

Kim, Sojeong; Choi, Soo-Hyung; Lee, Won Bo

Anion exchange membranes(AEMs) have been widely studied due to their various applications, especially for Fuel cells. Previous proton exchange membranes(PEMs), such as Nafions® have better conductivity than AEMs so far. However, technical limitations such as slow electrode kinetics, carbon monoxide (CO) poisoning of metal catalysts, high methanol crossover and high cost of Pt-based catalyst detered further usages. AEMs have advantages to supplement its drawbacks. AEMs are environmentally friendly and cost-efficient. Based on the well-defined block copolymer, self-assembled morphology is expected to have some relationship with its ionic conductivity. Recently AEMs based on various cations, including ammonium, phosphonium, guanidinium, imidazolium, metal cation, and benzimidazolium cations have been developed and extensively studied with the aim to prepare high- performance AEMs. But more fundamental approach, such as relationships between nanostructure and conductivity is needed. We use well-defined block copolymer Poly(styrene-block-isoprene) as a backbone which is synthesized by anionic polymerization. Then we graft various cationic functional groups and analysis the relation between morphology and conductivity. Theoretical and computational soft matter lab.

AEM and NMR: Tools for the Future of Groundwater Management

NASA Astrophysics Data System (ADS)

Abraham, J. D.; Cannia, J. C.; Lawrie, K.

2012-12-01

Within the world, understanding groundwater resources and their management are growing in importance to society as groundwater resources are stressed by drought and continued development. To minimize conflicts, tools and techniques need to be applied to support knowledge-based decisions and management. Airborne electromagnetic (AEM) surveys provide high-quality subsurface data not available from any other source for building the complex hydrogeologic frameworks needed by water-resource managers for effective groundwater management. Traditionally, point data, such as borehole logs, borehole geophysics, surface geophysics, and aquifer tests were interpolated over long distances to create hydrogeologic frameworks. These methods have enjoyed a long history of being the best available technology to inform our understanding of groundwater and how it moves. The AEM techniques proivde pathway for geoscientists to follow to develop more accurate descriptions of the hydrogeological framework. However, the critical and challenging measurements in characterizing aquifers include effective porosity and hydraulic conductivity. These parameters are not reliable derived from AEM. Typically, values for effective porosity and hydraulic conductivity are derived by lithological comparisons with published data; direct measurements of hydraulic conductivity acquired by a few constant head aquifer tests or slug tests; and expensive and time consuming laboratory measurements of cores which can be biased by sampling and the difficulty of making measurements on unconsolidated materials. Aquifer tests are considered to be the best method to gather information on hydraulic conductivity but are rare because of cost and difficult logistics. Also they are unique in design and interpretation from site to site. Nuclear Magnetic Resonance (NMR) can provide a direct measurement of the presence of water in the pore space of aquifer materials. Detection and direct measurement is possible due to the nuclear magnetization of the hydrogen (protons) in the water. These measurements are the basis of the familiar MRI (magnetic resonance imaging) in medical applications. NMR is also widely used in logging applications within the petroleum industry. Effective porosity values were derived directly from the borehole and surface NMR data, and hydraulic conductivity values were calculated using empirical relationships calibrated and verified with few laboratory permeameter and aquifer tests. NMR provides measurements of the effective porosity and hydraulic conductivity at a resolution not possible using traditional methods. Unlike aquifer tests, NMR logs are not unique in design and are applied in similar fashion from borehole to borehole providing a standard way of measuring hydraulic properties. When the hydraulic properties from the NMR are integrated with hydrogeological framework interpretations of AEM data large areas can be characterized. This allows a much more robust method for conceptualizing groundwater models then simply using previously published data for assigning effective porosity and hydraulic conductivity. Examples from the North Platte River Basin in Nebraska and the Murray Darling Basin of Australia illustrate that borehole and surface NMR allows superior, rapid measurements of the complexities of aquifers within when integrated with AEM.

WORKING WITH WHAEM2000: SOURCE WATER ASSESSMENT FOR A GLACIAL OUTWASH WELLFIELD, VINCENNES, INDIANA (REVISED MARCH 2003)

EPA Science Inventory

The purpose of this document is to introduce the use of the ground water geohydrology computer program WhAEM for Microsoft Windows (32-bit), or WhAEM2000. WhAEM2000 is a public domain, ground-water flow model designed to facilitate capture zone delineation and protection area map...

Using analytic element models to delineate drinking water source protection areas.

PubMed

Raymond, Heather A; Bondoc, Michael; McGinnis, John; Metropulos, Kathy; Heider, Pat; Reed, Allison; Saines, Steve

2006-01-01

Since 1999, Ohio EPA hydrogeologists have used two analytic element models (AEMs), the proprietary software GFLOW and U.S. EPA's WhAEM, to delineate protection areas for 535 public water systems. Both models now use the GFLOW2001 solution engine, integrate well with Geographic Information System (GIS) technology, have a user-friendly graphical interface, are capable of simulating a variety of complex hydrogeologic settings, and do not rely upon a model grid. These features simplify the modeling process and enable AEMs to bridge the gap between existing simplistic delineation methods and more complex numerical models. Ohio EPA hydrogeologists demonstrated that WhAEM2000 and GFLOW2000 were capable of producing capture zones similar to more widely accepted models by applying the AEMs to eight sites that had been previously delineated using other methods. After the Ohio EPA delineated protection areas using AEMs, more simplistic delineation methods used by other states (volumetric equation and arbitrary fixed radii) were applied to the same water systems to compare the differences between various methods. GIS software and two-tailed paired t-tests were used to quantify the differences in protection areas and analyze the data. The results of this analysis demonstrate that AEMs typically produce significantly different protection areas than the most simplistic delineation methods, in terms of total area and shape. If the volumetric equation had been used instead of AEMs, Ohio would not have protected 265 km2 of critical upgradient area and would have overprotected 269 km2 of primarily downgradient land. Since an increasing number of land-use restrictions are being tied to drinking water protection areas, this analysis has broad policy implications.

WORKING WITH WHAEM2000: CAPTURE ZONE DELINEATION FOR A CITY WELLFIELD IN A VALLEY FILL GLACIAL OUTWASH AQUIFER SUPPORTING WELLHEAD PROTECTION

EPA Science Inventory

The purpose of this document is to introduce through a case study the use of the ground water geohydrology computer program WhAEM for Microsoft Windows (32-bit), or WhAEM2000. WhAEM2000 is a public domain, ground-water flow model designed to facilitate capture zone delineation an...

Is Queen Victoria Lecturing Today? Teaching Human Sexuality Using Famous Personalities.

ERIC Educational Resources Information Center

Parrot, Andrea

1987-01-01

Describes a technique for teaching human sexuality in the undergraduate classroom in which the teacher portrays a famous person presenting sexuality topics from his or her perspective. Describes the content of several of these "guest lecturers." Explains the benefits and potential problems of the method. (AEM)

Design rules for successful governmental payments for ecosystem services: Taking agri-environmental measures in Germany as an example.

PubMed

Meyer, Claas; Reutter, Michaela; Matzdorf, Bettina; Sattler, Claudia; Schomers, Sarah

2015-07-01

In recent years, increasing attention has been paid to financial environmental policy instruments that have played important roles in solving agri-environmental problems throughout the world, particularly in the European Union and the United States. The ample and increasing literature on Payments for Ecosystem Services (PES) and agri-environmental measures (AEMs), generally understood as governmental PES, shows that certain single design rules may have an impact on the success of a particular measure. Based on this research, we focused on the interplay of several design rules and conducted a comparative analysis of AEMs' institutional arrangements by examining 49 German cases. We analyzed the effects of the design rules and certain rule combinations on the success of AEMs. Compliance and noncompliance with the hypothesized design rules and the success of the AEMs were surveyed by questioning the responsible agricultural administration and the AEMs' mid-term evaluators. The different rules were evaluated in regard to their necessity and sufficiency for success using Qualitative Comparative Analysis (QCA). Our results show that combinations of certain design rules such as environmental goal targeting and area targeting conditioned the success of the AEMs. Hence, we generalize design principles for AEMs and discuss implications for the general advancement of ecosystem services and the PES approach in agri-environmental policies. Moreover, we highlight the relevance of the results for governmental PES program research and design worldwide. Copyright © 2015 Elsevier Ltd. All rights reserved.

Spatially constrained Bayesian inversion of frequency- and time-domain electromagnetic data from the Tellus projects

NASA Astrophysics Data System (ADS)

Kiyan, Duygu; Rath, Volker; Delhaye, Robert

2017-04-01

The frequency- and time-domain airborne electromagnetic (AEM) data collected under the Tellus projects of the Geological Survey of Ireland (GSI) which represent a wealth of information on the multi-dimensional electrical structure of Ireland's near-surface. Our project, which was funded by GSI under the framework of their Short Call Research Programme, aims to develop and implement inverse techniques based on various Bayesian methods for these densely sampled data. We have developed a highly flexible toolbox using Python language for the one-dimensional inversion of AEM data along the flight lines. The computational core is based on an adapted frequency- and time-domain forward modelling core derived from the well-tested open-source code AirBeo, which was developed by the CSIRO (Australia) and the AMIRA consortium. Three different inversion methods have been implemented: (i) Tikhonov-type inversion including optimal regularisation methods (Aster el al., 2012; Zhdanov, 2015), (ii) Bayesian MAP inversion in parameter and data space (e.g. Tarantola, 2005), and (iii) Full Bayesian inversion with Markov Chain Monte Carlo (Sambridge and Mosegaard, 2002; Mosegaard and Sambridge, 2002), all including different forms of spatial constraints. The methods have been tested on synthetic and field data. This contribution will introduce the toolbox and present case studies on the AEM data from the Tellus projects.

Standard spacecraft procurement analysis: A case study in NASA-DoD coordination in space programs. Ph.D. Thesis - Rand Graduate Inst.

NASA Technical Reports Server (NTRS)

Harris, E. D.

1980-01-01

The Space Test Program Standard Satellite (STPSS), a design proposed by the Air Force, and two NASA candidates, the Applications Explorer Mission spacecraft (AEM) and the Multimission Modular Spacecraft (MMS), were considered during the first phase. During the second phase, a fourth candidate was introduced, a larger, more capable AEM (L-AEM), configured by the Boeing Company under NASA sponsorship to meet the specifications jointly agreed upon by NASA and the Air Force. Total program costs for a variety of procurement options, each of which is capable of performing all of the Air Force Space Test Program missions during the 1980-1990 time period, were used as the principal measure for distinguishing among procurement options. Program cost does not provide a basis for choosing among the AEM, STPSS, and MMS spacecraft, given their present designs. The availability of the L-AEM spacecraft, or some very similar design, would provide a basis for minimizing the cost of the Air Force Space Test Program.

Comments on: Christensen, N., and Lawrie, K., 2012. Resolution analyses for selecting an appropriate airborne electromagnetic (AEM) system, Exploration Geophysics, 43, 213-227

NASA Astrophysics Data System (ADS)

Smiarowski, Adam; Mulè, Shane

2015-06-01

The AEM in-line component is added to the posterior model covariance matrix analysis done by Christensen and Lawrie, who estimated resolution of data in an inversion program. They compared two AEM systems: SkyTEM and CGG's TEMPEST™. Here, we clarify points made about TEMPEST™ and extend the analysis to include the in-line component.

Global transcriptomic analysis suggests carbon dioxide as an environmental stressor in spaceflight: A systems biology GeneLab case study.

PubMed

Beheshti, Afshin; Cekanaviciute, Egle; Smith, David J; Costes, Sylvain V

2018-03-08

Spaceflight introduces a combination of environmental stressors, including microgravity, ionizing radiation, changes in diet and altered atmospheric gas composition. In order to understand the impact of each environmental component on astronauts it is important to investigate potential influences in isolation. Rodent spaceflight experiments involve both standard vivarium cages and animal enclosure modules (AEMs), which are cages used to house rodents in spaceflight. Ground control AEMs are engineered to match the spaceflight environment. There are limited studies examining the biological response invariably due to the configuration of AEM and vivarium housing. To investigate the innate global transcriptomic patterns of rodents housed in spaceflight-matched AEM compared to standard vivarium cages we utilized publicly available data from the NASA GeneLab repository. Using a systems biology approach, we observed that AEM housing was associated with significant transcriptomic differences, including reduced metabolism, altered immune responses, and activation of possible tumorigenic pathways. Although we did not perform any functional studies, our findings revealed a mild hypoxic phenotype in AEM, possibly due to atmospheric carbon dioxide that was increased to match conditions in spaceflight. Our investigation illustrates the process of generating new hypotheses and informing future experimental research by repurposing multiple space-flown datasets.

The effect of spaceflight on mouse olfactory bulb volume, neurogenesis, and cell death indicates the protective effect of novel environment.

PubMed

Latchney, Sarah E; Rivera, Phillip D; Mao, Xiao W; Ferguson, Virginia L; Bateman, Ted A; Stodieck, Louis S; Nelson, Gregory A; Eisch, Amelia J

2014-06-15

Space missions necessitate physiological and psychological adaptations to environmental factors not present on Earth, some of which present significant risks for the central nervous system (CNS) of crewmembers. One CNS region of interest is the adult olfactory bulb (OB), as OB structure and function are sensitive to environmental- and experience-induced regulation. It is currently unknown how the OB is altered by spaceflight. In this study, we evaluated OB volume and neurogenesis in mice shortly after a 13-day flight on Space Shuttle Atlantis [Space Transport System (STS)-135] relative to two groups of control mice maintained on Earth. Mice housed on Earth in animal enclosure modules that mimicked the conditions onboard STS-135 (AEM-Ground mice) had greater OB volume relative to mice maintained in standard housing on Earth (Vivarium mice), particularly in the granule (GCL) and glomerular (GL) cell layers. AEM-Ground mice also had more OB neuroblasts and fewer apoptotic cells relative to Vivarium mice. However, the AEM-induced increase in OB volume and neurogenesis was not seen in STS-135 mice (AEM-Flight mice), suggesting that spaceflight may have negated the positive effects of the AEM. In fact, when OB volume of AEM-Flight mice was considered, there was a greater density of apoptotic cells relative to AEM-Ground mice. Our findings suggest that factors present during spaceflight have opposing effects on OB size and neurogenesis, and provide insight into potential strategies to preserve OB structure and function during future space missions. Copyright © 2014 the American Physiological Society.

Airborne EM survey in volcanoes : Application to a volcanic hazards assessment

NASA Astrophysics Data System (ADS)

Mogi, T.

2010-12-01

Airborne electromagnetics (AEM) is a useful tool for investigating subsurface structures of volcanoes because it can survey large areas involving inaccessible areas. Disadvantages include lower accuracy and limited depth of investigation. AEM has been widely used in mineral exploration in frontier areas, and have been applying to engineering and environmental fields, particularly in studies involving active volcanoes. AEM systems typically comprise a transmitter and a receiver on an aircraft or in a towed bird, and although effective for surveying large areas, their penetration depth is limited because the distance between the transmitter and receiver is small and higher-frequency signals are used. To explore deeper structures using AEM, a semi-airborne system called GRounded Electrical source Airborne Transient ElectroMagnetics (GREATEM) has been developed. The system uses a grounded-electrical-dipole as the transmitter and generates horizontal electric fields. The GREATEM technology, first proposed by Mogi et al. (1998), has recently been improved and used in practical surveys (Mogi et al., 2009). The GREATEM survey system was developed to increase the depth of investigation possible using AEM. The method was tested in some volcanoes at 2004-2005. Here I will talk about some results of typical AEM surveys and GREATEM surveys in some volcanoes in Japan to mitigate hazards associated with volcano eruption. Geologic hazards caused by volcanic eruptions can be mitigated by a combination of prediction, preparedness and land-use control. Risk management depends on the identification of hazard zones and forecasting of eruptions. Hazard zoning involves the mapping of deposits which have formed during particular phases of volcanic activity and their extrapolation to identify the area which would be likely to suffer a similar hazard at some future time. The mapping is usually performed by surface geological surveys of volcanic deposits. Resistivity mapping by AEM is useful tool to identify each volcanic deposit on the surface and at shallower depth as well. This suggests that more efficient hazard map involving subsurface information can be supplied by AEM resistivity mapping.

INNOVATIVE CONCEPTS FOR DETECTING AND LOCATING LEAKS IN WASTE IMPOUNDMENT LINER SYSTEMS: ACOUSTIC EMISSION MONITORING AND TIME DOMAIN REFLECTOMETRY

EPA Science Inventory

This project is part of a program to investigate the use of innovative techniques for detecting and locating leaks in waste impoundment liners. Laboratory and small scale field studies were undertaken to evaluate the potential of Acoustic Emission Monitoring (AEM) and Time Domain...

Analysis of Brick Masonry Wall using Applied Element Method

NASA Astrophysics Data System (ADS)

Lincy Christy, D.; Madhavan Pillai, T. M.; Nagarajan, Praveen

2018-03-01

The Applied Element Method (AEM) is a versatile tool for structural analysis. Analysis is done by discretising the structure as in the case of Finite Element Method (FEM). In AEM, elements are connected by a set of normal and shear springs instead of nodes. AEM is extensively used for the analysis of brittle materials. Brick masonry wall can be effectively analyzed in the frame of AEM. The composite nature of masonry wall can be easily modelled using springs. The brick springs and mortar springs are assumed to be connected in series. The brick masonry wall is analyzed and failure load is determined for different loading cases. The results were used to find the best aspect ratio of brick to strengthen brick masonry wall.

A Highly Hydroxide Conductive, Chemically Stable Anion Exchange Membrane, Poly(2,6 dimethyl 1,4 phenylene oxide)- b -Poly(vinyl benzyl trimethyl ammonium), for Electrochemical Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandey, Tara P.; Sarode, Himanshu N.; Yang, Yating

A chemically stable copolymer [poly(2,6 dimethyl 1,4 phenylene oxide)-b-poly(vinyl benzyl trimethyl ammonium)] with two ion exchange capacities, 3.2 and 2.9 meq g-1, was prepared as anion exchange membranes (AEM-3.2 and AEM-2.9). These materials showed high OH- conductivities of 138 mS.cm-1 and 106 mS.cm-1, for AEM-3.2 and AEM-2.9 respectively, at 60°C, and 95% RH. The OH- conductivity = 45 mS.cm-1 for AEM-3.2 at 60% RH and 60°C in the absence of CO2. Amongst the ions studied, only OH- is fully dissociated at high RH. The lower Ea = 10–13 kJ.mol-1 for OH- compared to F- ~ 20 kJ.mol-1 in conductivity measurements,more » and of H2O from self-diffusion coefficients suggests the presence of a Grotthuss hopping transport mechanism in OH- transport. PGSE-NMR of H2O and F- show that the membranes have low tortuosity, 1.8 and 1.2, and high water self-diffusion coefficients, 0.66 and 0.26 × 10-5 cm2.s-1, for AEM-3.2 and AEM-2.9 respectively. SAXS and TEM show that the membrane has several different sized water environments, ca. 62 nm, 20 nm, and 3.5 nm. The low water uptake, λ = 9–12, reduced swelling, and high OH- conductivity, with no chemical degradation over two weeks, suggests that the membrane is a strong candidate for electrochemical applications.« less

Evaluation of rodent spaceflight in the NASA animal enclosure module for an extended operational period (up to 35 days).

PubMed

Moyer, Eric L; Dumars, Paula M; Sun, Gwo-Shing; Martin, Kara J; Heathcote, David G; Boyle, Richard D; Skidmore, Mike G

2016-01-01

The National Aeronautics and Space Administration Animal Enclosure Module (AEM) was developed as a self-contained rodent habitat for shuttle flight missions that provides inhabitants with living space, food, water, ventilation, and lighting, and this study reports whether, after minimal hardware modification, the AEM could support an extended term up to 35 days for Sprague-Dawley rats and C57BL/6 female mice for use on the International Space Station. Success was evaluated based on comparison of AEM housed animals to that of vivarium housed and to normal biological ranges through various measures of animal health and well-being, including animal health evaluations, animal growth and body masses, organ masses, rodent food bar consumption, water consumption, and analysis of blood contents. The results of this study confirmed that the AEMs could support 12 adult female C57BL/6 mice for up to 35 days with self-contained RFB and water, and the AEMs could also support 5 adult male Sprague-Dawley rats for 35 days with external replenishment of diet and water. This study has demonstrated the capability and flexibility of the AEM to operate for up to 35 days with minor hardware modification. Therefore, with modifications, it is possible to utilize this hardware on the International Space Station or other operational platforms to extend the space life science research use of mice and rats.

A Pd/C-CeO2 Anode Catalyst for High-Performance Platinum-Free Anion Exchange Membrane Fuel Cells.

PubMed

Miller, Hamish A; Lavacchi, Alessandro; Vizza, Francesco; Marelli, Marcello; Di Benedetto, Francesco; D'Acapito, Francesco; Paska, Yair; Page, Miles; Dekel, Dario R

2016-05-10

One of the biggest obstacles to the dissemination of fuel cells is their cost, a large part of which is due to platinum (Pt) electrocatalysts. Complete removal of Pt is a difficult if not impossible task for proton exchange membrane fuel cells (PEM-FCs). The anion exchange membrane fuel cell (AEM-FC) has long been proposed as a solution as non-Pt metals may be employed. Despite this, few examples of Pt-free AEM-FCs have been demonstrated with modest power output. The main obstacle preventing the realization of a high power density Pt-free AEM-FC is sluggish hydrogen oxidation (HOR) kinetics of the anode catalyst. Here we describe a Pt-free AEM-FC that employs a mixed carbon-CeO2 supported palladium (Pd) anode catalyst that exhibits enhanced kinetics for the HOR. AEM-FC tests run on dry H2 and pure air show peak power densities of more than 500 mW cm(-2) . © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydroxide based Benzyltrimethylammonium degradation: Quantification of rates and degradation technique development

DOE PAGES

Sturgeon, Matthew R.; Macomber, Clay S.; Engtrakul, Chaiwat; ...

2015-01-21

Anion exchange membranes (AEMs) are of interest as hydroxide conducting polymer electrolytes in electrochemical devices like fuel cells and electrolyzers. AEMs require hydroxide stable covalently tetherable cations to ensure required conductivity. Benzyltrimethylammonium (BTMA) has been the covalently tetherable cation that has been most often employed in anion exchange membranes because it is reasonably basic, compact (limited number of atoms per charge), and easily/cheaply synthesized. Several reports exist that have investigated hydroxide stability of BTMA under specific conditions, but consistency within these reports and comparisons between them have not yet been made. While the hydroxide stability of BTMA has been believedmore » to be a limitation for AEMs, this stability has not been thoroughly reported. In this paper, we have found that several methods reported have inherent flaws in their findings due to the difficulty of performing degradation experiments at high temperature and high pH. In order to address these shortcomings, we have developed a reliable, standardized method of determining cation degradation under conditions similar/relevant to those expected in electrochemical devices. The experimental method has been employed to determine BTMA stabilities at varying cation concentrations and elevated temperatures, and has resulted in improved experimental accuracy and reproducibility. Finally and most notably, these results have shown that BTMA is quite stable at 80°C (half-life of ~4 years), a significant increase in stability over what had been reported previously.« less

A green approach for preparing anion exchange membrane based on cardo polyetherketone powders

NASA Astrophysics Data System (ADS)

Hu, Jue; Zhang, Chengxu; Zhang, Xiaodong; Chen, Longwei; Jiang, Lin; Meng, Yuedong; Wang, Xiangke

2014-12-01

Anion exchange membranes (AEMs) have attracted great attention due to their irreplaceable role in platinum-free fuel cell applications. The majority of AEM preparations have been performed in two steps: the grafting of functional groups and quaternization. Here, we adopted a simpler, more eco-friendly approach for the first time to prepare AEMs by atmospheric-pressure plasma-grafting. This approach enables the direct introduction of anion exchange groups (benzyltrimethylammonium groups) into the polymer matrix, overcoming the need for toxic chloromethyl ether and quaternization reagents. Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and 1H NMR spectroscopy results demonstrate that benzyltrimethylammonium groups have been successfully grafted into the cardo polyetherketone (PEK-C) matrix. Thermogravimetric analysis reveals that the plasma-grafting technique is a facile and non-destructive method able to improve the thermal stability of the polymer matrix due to the strong preservation of the PEK-C backbone structure and the cross-linking of the grafted side chains. The plasma-grafted PG-NOH membrane, which shows satisfactory alcohol resistance (ethanol permeability of 6.3 × 10-7 cm2 s-1), selectivity (1.2 × 104 S s cm-3), thermal stability (safely used below 130 °C), chemical stability, anion conductivity (7.7 mS cm-1 at 20 °C in deionized water) and mechanical properties is promising for the construction of high-performance fuel cells.

Solid-State Water Electrolysis with an Alkaline Membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leng, YJ; Chen, G; Mendoza, AJ

2012-06-06

We report high-performance, durable alkaline membrane water electrolysis in a solid-state cell. An anion exchange membrane (AEM) and catalyst layer ionomer for hydroxide ion conduction were used without the addition of liquid electrolyte. At 50 degrees C, an AEM electrolysis cell using iridium oxide as the anode catalyst and Pt black as the cathode catalyst exhibited a current density of 399 mA/cm(2) at 1.80 V. We found that the durability of the AEM-based electrolysis cell could be improved by incorporating a highly durable ionomer in the catalyst layer and optimizing the water feed configuration. We demonstrated an AEM-based electrolysis cellmore » with a lifetime of > 535 h. These first-time results of water electrolysis in a solid-state membrane cell are promising for low-cost, scalable hydrogen production.« less

Investigation on γ-irradiated PP/ethylene acrylic elastomer TPVs by rheological and thermal approaches

NASA Astrophysics Data System (ADS)

Dutta, Anindya; Ghosh, Anup K.

2018-03-01

Polypropylene (PP) was melt blended with varying concentration of ethylene acrylic elastomer (AEM) in a twin screw extruder and then γ-irradiated at several radiation doses to achieve a series of thermoplastic vulcanizates (TPV). The effect of AEM concentration and γ-irradiation on flow characteristics, crystallization and thermal degradation of blends were explained using melt dynamic rheology, differential scanning calorimetry and thermogravimetric analysis. Gel content values and dynamic rheological data of PP and AEM at different radiation doses confirmed the incessant scissioning of PP chains with radiation doses except for highest radiation dose, where crosslinking of PP chains took place and the incessant crosslinking of AEM chains irrespective of radiation doses. Oxidative degradation of PP was confirmed by FTIR spectroscopy, which also exhibited absence of any chemical interaction between two constituent polymers. Normalized crystallinity and melting point of compositions, obtained from DSC, decreased with the radiation doses. Furthermore, with the radiation doses clear shifts of maxima of the melting peak towards the lower temperature were observed for neat PP and blends. Thermal stability of PP and blends, as observed by TGA, reduced significantly with irradiation; whereas for AEM, no discernable change was observed. Enhanced chain scissioning of PP in presence of AEM reduced the thermal stability of blends, especially at lower irradiation. This reduction of thermal stability was established by "rule of mixture", applied to the activation energy of thermal degradation. Thus, optimization of radiation doses to prepare TPVs was established.

Evaluation of rodent spaceflight in the NASA animal enclosure module for an extended operational period (up to 35 days)

PubMed Central

Moyer, Eric L; Dumars, Paula M; Sun, Gwo-Shing; Martin, Kara J; Heathcote, David G; Boyle, Richard D; Skidmore, Mike G

2016-01-01

The National Aeronautics and Space Administration Animal Enclosure Module (AEM) was developed as a self-contained rodent habitat for shuttle flight missions that provides inhabitants with living space, food, water, ventilation, and lighting, and this study reports whether, after minimal hardware modification, the AEM could support an extended term up to 35 days for Sprague-Dawley rats and C57BL/6 female mice for use on the International Space Station. Success was evaluated based on comparison of AEM housed animals to that of vivarium housed and to normal biological ranges through various measures of animal health and well-being, including animal health evaluations, animal growth and body masses, organ masses, rodent food bar consumption, water consumption, and analysis of blood contents. The results of this study confirmed that the AEMs could support 12 adult female C57BL/6 mice for up to 35 days with self-contained RFB and water, and the AEMs could also support 5 adult male Sprague-Dawley rats for 35 days with external replenishment of diet and water. This study has demonstrated the capability and flexibility of the AEM to operate for up to 35 days with minor hardware modification. Therefore, with modifications, it is possible to utilize this hardware on the International Space Station or other operational platforms to extend the space life science research use of mice and rats. PMID:28725722

Simulation of wave propagation inside a human eye: acoustic eye model (AEM)

NASA Astrophysics Data System (ADS)

Požar, T.; Halilovič, M.; Horvat, D.; Petkovšek, R.

2018-02-01

The design and development of the acoustic eye model (AEM) is reported. The model consists of a computer-based simulation that describes the propagation of mechanical disturbance inside a simplified model of a human eye. The capabilities of the model are illustrated with examples, using different laser-induced initial loading conditions in different geometrical configurations typically occurring in ophthalmic medical procedures. The potential of the AEM is to predict the mechanical response of the treated eye tissue in advance, thus complementing other preliminary procedures preceding medical treatments.

Mapping Aquifer Systems with Airborne Electromagnetics in the Central Valley of California.

PubMed

Knight, Rosemary; Smith, Ryan; Asch, Ted; Abraham, Jared; Cannia, Jim; Viezzoli, Andrea; Fogg, Graham

2018-03-09

The passage of the Sustainable Groundwater Management Act in California has highlighted a need for cost-effective ways to acquire the data used in building conceptual models of the aquifer systems in the Central Valley of California. One approach would be the regional implementation of the airborne electromagnetic (AEM) method. We acquired 104 line-kilometers of data in the Tulare Irrigation District, in the Central Valley, to determine the depth of investigation (DOI) of the AEM method, given the abundance of electrically conductive clays, and to assess the usefulness of the method for mapping the hydrostratigraphy. The data were high quality providing, through inversion of the data, models displaying the variation in electrical resistivity to a depth of approximately 500 m. In order to transform the resistivity models to interpreted sections displaying lithology, we established the relationship between resistivity and lithology using collocated lithology logs (from drillers' logs) and AEM data. We modeled the AEM response and employed a bootstrapping approach to solve for the range of values in the resistivity model corresponding to sand and gravel, mixed coarse and fine, and clay in the unsaturated and saturated regions. The comparison between the resulting interpretation and an existing cross section demonstrates that AEM can be an effective method for mapping the large-scale hydrostratigraphy of aquifer systems in the Central Valley. The methods employed and developed in this study have widespread application in the use of the AEM method for groundwater management in similar geologic settings. © 2018 The Authors. Groundwater published by Wiley Periodicals, Inc. on behalf of National Ground Water Association.

Sensitivity of airborne geophysical data to sublacustrine and near-surface permafrost thaw

USGS Publications Warehouse

Minsley, Burke J.; Wellman, Tristan; Walvoord, Michelle Ann; Revil, Andre

2014-01-01

A coupled hydrogeophysical forward and inverse modeling approach is developed to illustrate the ability of frequency-domain airborne electromagnetic (AEM) data to characterize subsurface physical properties associated with sublacustrine permafrost thaw during lake-talik formation. Numerical modeling scenarios are evaluated that consider non-isothermal hydrologic responses to variable forcing from different lake depths and for different hydrologic gradients. A novel physical property relationship connects the dynamic distribution of electrical resistivity to ice saturation and temperature outputs from the SUTRA groundwater simulator with freeze–thaw physics. The influence of lithology on electrical resistivity is controlled by a surface conduction term in the physical property relationship. Resistivity models, which reflect changes in subsurface conditions, are used as inputs to simulate AEM data in order to explore the sensitivity of geophysical observations to permafrost thaw. Simulations of sublacustrine talik formation over a 1000-year period are modeled after conditions found in the Yukon Flats, Alaska. Synthetic AEM data are analyzed with a Bayesian Markov chain Monte Carlo algorithm that quantifies geophysical parameter uncertainty and resolution. Major lithological and permafrost features are well resolved by AEM data in the examples considered. The subtle geometry of partial ice saturation beneath lakes during talik formation cannot be resolved using AEM data, but the gross characteristics of sub-lake resistivity models reflect bulk changes in ice content and can identify the presence of a talik. A final synthetic example compares AEM and ground-based electromagnetic responses for their ability to resolve shallow permafrost and thaw features in the upper 1–2 m below ground outside the lake margin.

The bedrock electrical conductivity map of the UK

NASA Astrophysics Data System (ADS)

Beamish, David

2013-09-01

Airborne electromagnetic (AEM) surveys, when regionally extensive, may sample a wide-range of geological formations. The majority of AEM surveys can provide estimates of apparent (half-space) conductivity and such derived data provide a mapping capability. Depth discrimination of the geophysical mapping information is controlled by the bandwidth of each particular system. The objective of this study is to assess the geological information contained in accumulated frequency-domain AEM survey data from the UK where existing geological mapping can be considered well-established. The methodology adopted involves a simple GIS-based, spatial join of AEM and geological databases. A lithology-based classification of bedrock is used to provide an inherent association with the petrophysical rock parameters controlling bulk conductivity. At a scale of 1:625k, the UK digital bedrock geological lexicon comprises just 86 lithological classifications compared with 244 standard lithostratigraphic assignments. The lowest common AEM survey frequency of 3 kHz is found to provide an 87% coverage (by area) of the UK formations. The conductivities of the unsampled classes have been assigned on the basis of inherent lithological associations between formations. The statistical analysis conducted uses over 8 M conductivity estimates and provides a new UK national scale digital map of near-surface bedrock conductivity. The new baseline map, formed from central moments of the statistical distributions, allows assessments/interpretations of data exhibiting departures from the norm. The digital conductivity map developed here is believed to be the first such UK geophysical map compilation for over 75 years. The methodology described can also be applied to many existing AEM data sets.

AEM-7 electric locomotive testing at the Transportation Test Center

DOT National Transportation Integrated Search

1981-01-01

This report describes the tests conducted at the Transportation Test Center (TTC) on the first production AEM-7 locomotive, AMTRAK 900. These tests, which were conducted between April 1980 and May 1981, were to evaluate the locomotive characteristics...

The 727 approach energy management system avionics specification (preliminary)

NASA Technical Reports Server (NTRS)

Jackson, D. O.; Lambregts, A. A.

1976-01-01

Hardware and software requirements for an Approach Energy Management System (AEMS) consisting of an airborne digital computer and cockpit displays are presented. The displays provide the pilot with a visual indication of when to manually operate the gear, flaps, and throttles during a delayed flap approach so as to reduce approach time, fuel consumption, and community noise. The AEMS is an independent system that does not interact with other navigation or control systems, and is compatible with manually flown or autopilot coupled approaches. Operational use of the AEMS requires a DME ground station colocated with the flight path reference.

Joint Base Langley-Eustis

Science.gov Websites

Advanced Environmental Management Training (AEM) Advanced Environmental Management Phase I Training (AEM Phase I) Leadership Environmental Management and Competency Training (LEMAC) Basic Environmental Management Training (BEMA) Environmental Training Information Fort Eustis Chapel Fort Eustis Command Judge

Alkaline degradation studies of anion exchange polymers to enable new membrane designs

NASA Astrophysics Data System (ADS)

Nunez, Sean Andrew

Current performance targets for anion-exchange membrane (AEM) fuel cells call for greater than 95% alkaline stability for 5000 hours at temperatures up to 120 °C. Using this target temperature of 120 °C, an incisive 1H NMR-based alkaline degradation method to identify the degradation products of n-alkyl spacer tetraalkylammonium cations in various AEM polymers and small molecule analogs. Herein, the degradation mechanisms and rates of benzyltrimethylammonium-, n-alkyl interstitial spacer- and n-alkyl terminal pendant-cations are studied on several architectures. These findings demonstrate that benzyltrimethylammonium- and n-alkyl terminal pendant cations are more labile than an n-alkyl interstitial spacer cation and conclude that Hofmann elimination is not the predominant mechanism of alkaline degradation. Additionally, the alkaline stability of an n-alkyl interstitial spacer cation is enhanced when combined with an n-alkyl terminal pendant. Interestingly, at 120 °C, an inverse trend was found in the overall alkaline stability of AEM poly(styrene) and AEM poly(phenylene oxide) samples than was previously shown at 80 °C. Successive small molecule studies suggest that at 120 °C, an anion-induced 1,4-elimination degradation mechanism may be activated on styrenic AEM polymers bearing an acidic alpha-hydrogen. In addition, an ATR-FTIR based method was developed to assess the alkaline stability of solid membranes and any added resistance to degradation that may be due to differential solubilities and phase separation. To increase the stability of anion exchange membranes, Oshima magnesate--halogen exchange was demonstrated as a method for the synthesis of new anion exchange membranes that typically fail in the presence of organolithium or Grignard reagents alone. This new chemistry, applied to non-resinous polymers for the first time, proved effective for the n-akyl interstitial spacer functionalization of poly(phenylene oxide) and poly(styrene- co-ethylene-co-butylene-co-styrene) polymer backbones. The comprehensive methodologies for the assessment of alkaline stability in AEMs as well as the new synthetic methodologies are intended as a guide toward robust AEM synthetic designs that approach current performance standards.

Anticipatory Enrollment Management: Another Level of Enrollment Management

ERIC Educational Resources Information Center

Dennis, Marguerite J.

2012-01-01

Building on the principles of Enrollment Management (EM) and Strategic Enrollment Management (SEM), Anticipatory Enrollment Management (AEM) offers another level of managing enrollment: anticipating future enrollment. AEM is grounded in the basic principles of Customer Relationship Management (CRM) and includes strategic out-reach to parents and…

Improved performance of single-chamber microbial fuel cells through control of membrane deformation.

PubMed

Zhang, Xiaoyuan; Cheng, Shaoan; Huang, Xia; Logan, Bruce E

2010-03-15

Cation (CEMs) and anion exchange membrane (AEMs) are commonly used in microbial fuel cells (MFCs) to enhance Coulombic efficiencies (CEs) by reducing the flux of oxygen through the cathode to bacteria on the anode. AEMs typically work better than CEMs, but in initial experiments we observed the opposite using a membrane electrode assembly MFC. The reason was identified to be membrane deformation, which resulted in water and gas trapped between the membrane and cathode. To correct this, stainless steel mesh was used to press the membrane flat against the cathode. With the steel mesh, AEM performance increased to 46+/-4 W/m(3) in a single cathode MFC, and 98+/-14 W/m(3) in a double-cathode MFC. These power densities were higher than those using a CEM of 32+/-2 W/m(3) (single cathode) and 63+/-6 W/m(3) (double cathode). Higher pH gradients across the membrane and salt precipitation on the cathode were responsible for the reduced performance of the CEM compared to the AEM. CEs reached over 90% for both membranes at >2A/m(2). These results demonstrate the importance of avoiding water accumulation in thin films between membranes and electrodes, and explain additional reasons for poorer performance of CEMs compared to AEMs. (c) 2009 Elsevier B.V. All rights reserved.

Anxiety-Expectation Mediation Model of Library Anxiety.

ERIC Educational Resources Information Center

Jiao, Qun G.; Onwuegbuzie, Anthony J.

This study presents a test of the Anxiety-Expectation Mediation (AEM) model of library anxiety. The AEM model contains variables that are directly or indirectly related to information search performance, as measured by students' scores on their research proposals. This model posits that library anxiety and self-perception serve as factors that…

Ground-followup studies of the 1977 airborne electromagnetic survey in the Assifar and Mulhal areas, Wadi Bidah district, Kingdom of Saudi Arabia

USGS Publications Warehouse

Flanigan, Vincent J.; Sadek, Hamdy

1983-01-01

A brief review of the AEM ground-followup studies in the Wadi Bidah district suggests that most, if not all, of the AEM conductors are carbonaceous rocks. Secondary causes of conductivity are intense faulting and shearing.

A novel MVA-mediated pathway for isoprene production in engineered E. coli.

PubMed

Yang, Jianming; Nie, Qingjuan; Liu, Hui; Xian, Mo; Liu, Huizhou

2016-01-20

To deal with the increasingly severe energy crisis and environmental consequences, biofuels and biochemicals generated from renewable resources could serve as a promising alternative for replacing petroleum as a source of fuel and chemicals, among which isoprene (2-methyl-1,3-butadiene) in particular is of great significance in that it is an important platform chemical, which has been used in industrial production of synthetic rubber for tires and coatings or aviation fuel. We firstly introduced fatty acid decarboxylase (OleTJE) from Jeotgalicoccus species into E. coli to directly convert MVA(mevalonate) into 3-methy-3-buten-1-ol. And then to transform 3-methy-3-buten-1-ol to isoprene, oleate hydratase (OhyAEM) from Elizabethkingia meningoseptica was overexpressed in E. coli. A novel biosynthetic pathway of isoprene in E. coli was established by co-expressing the heterologous mvaE gene encoding acetyl-CoA acetyltransferase/HMG-CoA reductase and mvaS gene encoding HMG-CoA synthase from Enterococcus faecalis, fatty acid decarboxylase (OleTJE) and oleate hydratase (OhyAEM). Furthermore, to enhance isoprene production, a further optimization of expression level of OleTJE, OhyAEM was carried out by using different promoters and copy numbers of plasmids. Thereafter, the fermentation process was also optimized to improve the production of isoprene. The final engineered strain, YJM33, bearing the innovative biosynthetic pathway of isoprene, was found to produce isoprene up to 2.2 mg/L and 620 mg/L under flask and fed-batch fermentation conditions, respectively. In this study, by using metabolic engineering techniques, the novel MVA-mediated biosynthetic pathway of isoprene was successfully assembled in E. coli BL21(DE3) with the heterologous MVA upper pathway, OleTJE from Jeotgalicoccus species and OhyAEM from Elizabethkingia meningoseptica. Compared with traditional MVA pathway, the novel pathway is shortened by 3 steps. In addition, this is the first report on the reaction of converting MVA into 3-methy-3-buten-1-ol by fatty acid decarboxylase (OleTJE) from Jeotgalicoccus species. In brief, this study provided an alternative method for isoprene biosynthesis, which is largely different from the well-developed MEP pathway or MVA pathway.

3-D inversion of airborne electromagnetic data parallelized and accelerated by local mesh and adaptive soundings

NASA Astrophysics Data System (ADS)

Yang, Dikun; Oldenburg, Douglas W.; Haber, Eldad

2014-03-01

Airborne electromagnetic (AEM) methods are highly efficient tools for assessing the Earth's conductivity structures in a large area at low cost. However, the configuration of AEM measurements, which typically have widely distributed transmitter-receiver pairs, makes the rigorous modelling and interpretation extremely time-consuming in 3-D. Excessive overcomputing can occur when working on a large mesh covering the entire survey area and inverting all soundings in the data set. We propose two improvements. The first is to use a locally optimized mesh for each AEM sounding for the forward modelling and calculation of sensitivity. This dedicated local mesh is small with fine cells near the sounding location and coarse cells far away in accordance with EM diffusion and the geometric decay of the signals. Once the forward problem is solved on the local meshes, the sensitivity for the inversion on the global mesh is available through quick interpolation. Using local meshes for AEM forward modelling avoids unnecessary computing on fine cells on a global mesh that are far away from the sounding location. Since local meshes are highly independent, the forward modelling can be efficiently parallelized over an array of processors. The second improvement is random and dynamic down-sampling of the soundings. Each inversion iteration only uses a random subset of the soundings, and the subset is reselected for every iteration. The number of soundings in the random subset, determined by an adaptive algorithm, is tied to the degree of model regularization. This minimizes the overcomputing caused by working with redundant soundings. Our methods are compared against conventional methods and tested with a synthetic example. We also invert a field data set that was previously considered to be too large to be practically inverted in 3-D. These examples show that our methodology can dramatically reduce the processing time of 3-D inversion to a practical level without losing resolution. Any existing modelling technique can be included into our framework of mesh decoupling and adaptive sampling to accelerate large-scale 3-D EM inversions.

Effect of CO2 absorption on ion and water mobility in an anion exchange membrane

NASA Astrophysics Data System (ADS)

Peng, Jing; Roy, Asa L.; Greenbaum, Steve G.; Zawodzinski, Thomas A.

2018-03-01

We report the measured water uptake, density, ionic conductivity and water transport properties in Tokuyama A201 membrane in OH-, HCO3- and Cl- forms. The water uptake of the AEM varies with anion type in the order λ(OH-) > λ(HCO3-) > λ(Cl-) for samples equilibrated with the same water vapor activity (aw). The conductivity of the AEM is reduced by absorption of CO2. Pulsed-field gradient nuclear magnetic resonance (PFG-NMR) measurements were utilized to characterize the diffusivity of water and HCO3- ion. The anion diffusion coefficient and membrane conductivity are used to probe the applicability of the Nernst-Einstein equation in these AEMs.

DFT studies of the effectiveness of p-substituted diphenyl amine antioxidants in styrene-butadiene rubber through their Cu(II) coordination ability

NASA Astrophysics Data System (ADS)

Puškárová, Ingrid; Breza, Martin

2017-07-01

Structures of a series of diphenyl amine (DPA) antioxidants and of their complexes with Cu2+ were optimized at B3LYP level of theory. DPAs may be divided into two groups according to their molar antioxidant effectiveness (AEM). The effectiveness of high-AEM DPA antioxidants at 130 °C rises with decreasing spin densities at Cu atoms and with the increasing electron density Laplacian at Cu-N bond critical points in the 2[DPA…Cu]2+ complexes similarly as in the case of p-phenylene diamine antioxidants. No such trends are observed at 25 °C and for low- AEM DPA antioxidants.

Spanish Velar-Insertion and Analogy: A Usage-Based Diachronic Analysis

ERIC Educational Resources Information Center

Fondow, Steven Richard

2010-01-01

The theory of Analogical and Exemplar Modeling (AEM) suggests renewed discussion of the formalization of analogy and its possible incorporation in linguistic theory. AEM is a usage-based model founded upon Exemplar Modeling (Bybee 2007, Pierrehumbert 2001) that utilizes several principles of the Analogical Modeling of Language (Skousen 1992, 1995,…

Facets of Academic Excellence in Management Education: Conceptualization and Instrument Development in India

ERIC Educational Resources Information Center

Shukla, Amit; Singh, Shailendra

2016-01-01

The present work conceptualizes the idea of "Academic Excellence in Management Education" (AEM) in the Indian context. AEM is defined as a set of attributes that favourably and significantly contribute to a wide range of academic activities from faculty's perspective. The paper also describes grounded-theory approach for development of…

Characterization of shallow ocean sediments using the airborne electromagnetic method

NASA Technical Reports Server (NTRS)

Won, I. J.; Smits, K.

1986-01-01

Experimental airborne electromagnetic (AEM) survey data collected in Cape Cod Bay are used to derive continuous profiles of water depth, electrical depth, water conductivity, and bottom sediment conductivity. Through a few well-known empirical relationships, the conductivities are used, in turn, to derive density, porosity, sound speed, and acoustic reflectivity of the ocean bottom. A commercially available Dighem III AEM system was used for the survey without any significant modification. The helicopter-borne system operated at 385 and 7200 Hz; both were in a horizontal coplanar configuration. The interpreted profiles show good agreement with available ground truth data. Where no such data are available, the results appear to be very reasonable. Compared with the shipborne electrode array method, the AEM method can determine the necessary parameters at a much higher speed with a better lateral resolution over a wide range of water depths from 0 to perhaps 100 m. The bottom sediment conductivity that can be measured by the AEM method is closely related to physical properties of sediments, such as porosity, density, sound speed, and, indirectly, sediment types that might carry broad implications for various offshore activities.

A Cation-containing Polymer Anion Exchange Membrane based on Poly(norbornene)

NASA Astrophysics Data System (ADS)

Beyer, Frederick; Price, Samuel; Ren, Xiaoming; Savage, Alice

Cation-containing polymers are being studied widely for use as anion exchange membranes (AEMs) in alkaline fuel cells (AFCs) because AEMs offer a number of potential benefits including allowing a solid state device and elimination of the carbonate poisoning problem. The successful AEM will combine high performance from several orthogonal properties, having robust mechanical strength even when wet, high hydroxide conductivity, and the high chemical stability required for long device lifetimes. In this study, we have synthesized a model cationic polymer that combines three of the key advantages of Nafion. The polymer backbone based on semicrystalline atactic poly(norbornene) offers good mechanical properties. A flexible, ether-based tether between the backbone and fixed cation charged species (quaternary ammonium) should provide the low-Tg, hydrophilic environment required to facilitate OH- transport. Finally, methyl groups have been added at the beta position relative to the quaternary ammonium cation to prevent Hoffman elimination, one mechanism by which AEMs are neutralized in a high pH environment. In this poster, we will present our findings on mechanical properties, morphology, charge transport, and chemical stability of this material.

Direct glycerol fuel cell with polytetrafluoroethylene (PTFE) thin film separator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benipal, Neeva; Qi, Ji; Dalian Univ. of Technology, Dalian

Here, anion-exchange membrane-based direct glycerol fuel cells (AEM-DGFCs) can yield high power density, however challenges exist in developing chemically stable AEMs. Here, we demonstrate a porous PTFE thin film, a well-known chemical, electro-chemical, and thermal robust material that can serve as a separator between anode and cathode, thus achieving high DGFC’s performance. A simple aqueous-phase reduction method was used to prepare carbon nanotube supported PdAg nanoparticles (PdAg/CNT) with an average particle size of 2.9 nm. A DGFC using a PTFE thin film without any further modification with PdAg/CNT anode catalyst exhibits a peak power density of 214.7 mW cm –2more » at 80 °C, about 22.6% lower than a DGFC using a state-of-the-art AEM. We report a 5.8% decrease and 11.1% decrease in cell voltage for a PTFE thin film and AEM; similarly, the cell voltage degradation rate decreases from 1.2 to 0.8 mV h –1 for PTFE thin film, while for AEM, it decreases from 9.6 to 3.0 mV h –1 over an 80 h durability test period. Transmission electron microscopy results indicate that the average particle size of PdAg/CNT increases from 2.9 to 3.7 nm after 80 h discharge; this suggests that PdAg particle growth may be the main reason for the performance drop.« less

Direct glycerol fuel cell with polytetrafluoroethylene (PTFE) thin film separator

DOE PAGES

Benipal, Neeva; Qi, Ji; Dalian Univ. of Technology, Dalian; ...

2017-01-04

Here, anion-exchange membrane-based direct glycerol fuel cells (AEM-DGFCs) can yield high power density, however challenges exist in developing chemically stable AEMs. Here, we demonstrate a porous PTFE thin film, a well-known chemical, electro-chemical, and thermal robust material that can serve as a separator between anode and cathode, thus achieving high DGFC’s performance. A simple aqueous-phase reduction method was used to prepare carbon nanotube supported PdAg nanoparticles (PdAg/CNT) with an average particle size of 2.9 nm. A DGFC using a PTFE thin film without any further modification with PdAg/CNT anode catalyst exhibits a peak power density of 214.7 mW cm –2more » at 80 °C, about 22.6% lower than a DGFC using a state-of-the-art AEM. We report a 5.8% decrease and 11.1% decrease in cell voltage for a PTFE thin film and AEM; similarly, the cell voltage degradation rate decreases from 1.2 to 0.8 mV h –1 for PTFE thin film, while for AEM, it decreases from 9.6 to 3.0 mV h –1 over an 80 h durability test period. Transmission electron microscopy results indicate that the average particle size of PdAg/CNT increases from 2.9 to 3.7 nm after 80 h discharge; this suggests that PdAg particle growth may be the main reason for the performance drop.« less

The Application of Standards and Recommendations to Clinical Ethics Consultation in Practice: An Evaluation at German Hospitals.

PubMed

Schochow, Maximilian; Rubeis, Giovanni; Steger, Florian

2017-06-01

The executive board of the Academy for Ethics in Medicine (AEM) and two AEM working groups formulated standards and recommendations for clinical ethics consultation in 2010, 2011, and 2013. These guidelines comply with the international standards like those set by the American Society for Bioethics and Humanities. There is no empirical data available yet that could indicate whether these standards and recommendations have been implemented in German hospitals. This desideratum is addressed in the present study. We contacted 1.858 German hospitals between September 2013 and January 2014. A follow-up survey was conducted between October 2014 and January 2015. The data of the initial survey and the follow-up survey were merged and evaluated. The statements of the participants were compared with the standards and recommendations. The standards of the AEM concerning the tasks of clinical ethics consultation (including ethics consultation, ethics training and the establishment of policy guidelines) are employed by a majority of participants of the study. Almost all of these participants document their consultation activities by means of protocols or entries in the patient file. There are deviations from the recommendations of the AEM working groups regarding the drafting of statutes, activity reports, and financial support. The activities of clinical ethics consultation predominantly comply with the standards of the AEM and recommendations for the documentation. The recommendations for evaluation should be improved in practice. This applies particularly for activity reports in order to evaluate the activities. Internal evaluation could take place accordingly.

3D anisotropic modeling and identification for airborne EM systems based on the spectral-element method

NASA Astrophysics Data System (ADS)

Huang, Xin; Yin, Chang-Chun; Cao, Xiao-Yue; Liu, Yun-He; Zhang, Bo; Cai, Jing

2017-09-01

The airborne electromagnetic (AEM) method has a high sampling rate and survey flexibility. However, traditional numerical modeling approaches must use high-resolution physical grids to guarantee modeling accuracy, especially for complex geological structures such as anisotropic earth. This can lead to huge computational costs. To solve this problem, we propose a spectral-element (SE) method for 3D AEM anisotropic modeling, which combines the advantages of spectral and finite-element methods. Thus, the SE method has accuracy as high as that of the spectral method and the ability to model complex geology inherited from the finite-element method. The SE method can improve the modeling accuracy within discrete grids and reduce the dependence of modeling results on the grids. This helps achieve high-accuracy anisotropic AEM modeling. We first introduced a rotating tensor of anisotropic conductivity to Maxwell's equations and described the electrical field via SE basis functions based on GLL interpolation polynomials. We used the Galerkin weighted residual method to establish the linear equation system for the SE method, and we took a vertical magnetic dipole as the transmission source for our AEM modeling. We then applied fourth-order SE calculations with coarse physical grids to check the accuracy of our modeling results against a 1D semi-analytical solution for an anisotropic half-space model and verified the high accuracy of the SE. Moreover, we conducted AEM modeling for different anisotropic 3D abnormal bodies using two physical grid scales and three orders of SE to obtain the convergence conditions for different anisotropic abnormal bodies. Finally, we studied the identification of anisotropy for single anisotropic abnormal bodies, anisotropic surrounding rock, and single anisotropic abnormal body embedded in an anisotropic surrounding rock. This approach will play a key role in the inversion and interpretation of AEM data collected in regions with anisotropic geology.

Predicting Carbonate Species Ionic Conductivity in Alkaline Anion Exchange Membranes

DTIC Science & Technology

2012-06-01

This method has been used previously with both PEM and AEM fuel cells and demonstrated its ability to accurately predict ionic conductivity [2,9,24...water. In an AMFC, the mobile species is a hydroxide ion (OH - ) and in a PEM fuel cell , the proton is solvated with a water molecule forming...membrane synthesis techniques have produced polymer electrolyte membranes that are capable of transporting anions in alkaline membrane fuel cells

Aqueous Extract of Black Maca Prevents Metabolism Disorder via Regulating the Glycolysis/Gluconeogenesis-TCA Cycle and PPARα Signaling Activation in Golden Hamsters Fed a High-Fat, High-Fructose Diet.

PubMed

Wan, Wenting; Li, Hongxiang; Xiang, Jiamei; Yi, Fan; Xu, Lijia; Jiang, Baoping; Xiao, Peigen

2018-01-01

Maca ( Lepidium meyenii Walpers) has been used as a dietary supplement and ethnomedicine for centuries. Recently, maca has become a high profile functional food worldwide because of its multiple biological activities. This study is the first explorative research to investigate the prevention and amelioration capacity of the aqueous extract of black maca (AEM) on high-fat, high-fructose diet (HFD)-induced metabolism disorder in golden hamsters and to identify the potential mechanisms involved in these effects. For 20 weeks, 6-week-old male golden hamsters were fed the following respective diets: (1) a standard diet, (2) HFD, (3) HFD supplemented with metformin, or (4) HFD supplemented with three doses of AEM (300, 600, or 1,200 mg/kg). After 20 weeks, the golden hamsters that received daily AEM supplementation presented with the beneficial effects of improved hyperlipidemia, hyperinsulinemia, insulin resistance, and hepatic steatosis in vivo . Based on the hepatic metabolomic analysis results, alterations in metabolites associated with pathological changes were examined. A total of 194 identified metabolites were mapped to 46 relative metabolic pathways, including those of energy metabolism. In addition, via in silico profiling for secondary maca metabolites by a joint pharmacophore- and structure-based approach, a compound-target-disease network was established. The results revealed that 32 bioactive compounds in maca targeted 16 proteins involved in metabolism disorder. Considering the combined metabolomics and virtual screening results, we employed quantitative real-time PCR assays to verify the gene expression of key enzymes in the relevant pathways. AEM promoted glycolysis and inhibited gluconeogenesis via regulating the expression of key genes such as Gck and Pfkm . Moreover, AEM upregulated tricarboxylic acid (TCA) cycle flux by changing the concentrations of intermediates and increasing the mRNA levels of Aco2 , Fh , and Mdh2 . In addition, the lipid-lowering effects of AEM in boththe serum and liver may be partly related to PPARα signaling activation, including enhanced fatty acid β-oxidation and lipogenesis pathway inhibition. Together, our data demonstrated that AEM intervention significantly improved lipid and glucose metabolism disorder by regulating the glycolysis/gluconeogenesis-TCA cycle and by modulating gene expression levels involved in the PPARα signaling pathway.

Aqueous Extract of Black Maca Prevents Metabolism Disorder via Regulating the Glycolysis/Gluconeogenesis-TCA Cycle and PPARα Signaling Activation in Golden Hamsters Fed a High-Fat, High-Fructose Diet

PubMed Central

Wan, Wenting; Li, Hongxiang; Xiang, Jiamei; Yi, Fan; Xu, Lijia; Jiang, Baoping; Xiao, Peigen

2018-01-01

Maca (Lepidium meyenii Walpers) has been used as a dietary supplement and ethnomedicine for centuries. Recently, maca has become a high profile functional food worldwide because of its multiple biological activities. This study is the first explorative research to investigate the prevention and amelioration capacity of the aqueous extract of black maca (AEM) on high-fat, high-fructose diet (HFD)-induced metabolism disorder in golden hamsters and to identify the potential mechanisms involved in these effects. For 20 weeks, 6-week-old male golden hamsters were fed the following respective diets: (1) a standard diet, (2) HFD, (3) HFD supplemented with metformin, or (4) HFD supplemented with three doses of AEM (300, 600, or 1,200 mg/kg). After 20 weeks, the golden hamsters that received daily AEM supplementation presented with the beneficial effects of improved hyperlipidemia, hyperinsulinemia, insulin resistance, and hepatic steatosis in vivo. Based on the hepatic metabolomic analysis results, alterations in metabolites associated with pathological changes were examined. A total of 194 identified metabolites were mapped to 46 relative metabolic pathways, including those of energy metabolism. In addition, via in silico profiling for secondary maca metabolites by a joint pharmacophore- and structure-based approach, a compound-target-disease network was established. The results revealed that 32 bioactive compounds in maca targeted 16 proteins involved in metabolism disorder. Considering the combined metabolomics and virtual screening results, we employed quantitative real-time PCR assays to verify the gene expression of key enzymes in the relevant pathways. AEM promoted glycolysis and inhibited gluconeogenesis via regulating the expression of key genes such as Gck and Pfkm. Moreover, AEM upregulated tricarboxylic acid (TCA) cycle flux by changing the concentrations of intermediates and increasing the mRNA levels of Aco2, Fh, and Mdh2. In addition, the lipid-lowering effects of AEM in boththe serum and liver may be partly related to PPARα signaling activation, including enhanced fatty acid β-oxidation and lipogenesis pathway inhibition. Together, our data demonstrated that AEM intervention significantly improved lipid and glucose metabolism disorder by regulating the glycolysis/gluconeogenesis-TCA cycle and by modulating gene expression levels involved in the PPARα signaling pathway. PMID:29681858

Heat capacity mapping radiometer for AEM spacecraft

NASA Technical Reports Server (NTRS)

Sonnek, G. E.

1977-01-01

The operation, maintenance, and integration of the applications explorer mission heat capacity mapping radiometer is illustrated in block diagrams and detail schematics of circuit functions. Data format and logic timing diagrams are included along with radiometric and electronic calibration data. Mechanical and electrical configuration is presented to provide interface details for integration of the HCMR instrument to AEM spacecraft.

Active electrode monitoring. How to prevent unintentional thermal injury associated with monopolar electrosurgery at laparoscopy.

PubMed

Vancaillie, T G

1998-08-01

In recent years, the use of minimally invasive surgery (MIS) has expanded to a wide variety of surgical specialties. The increased popularity of the procedure, however, has been accompanied by its share of complications, including trocar lacerations and inadvertent thermal injuries to nontargeted tissues during monopolar electrosurgery. A survey on electrosurgical thermal injuries and three case studies are presented. The new technology of active electrode monitoring (AEM) is described. AEM eliminates stray currents generated by insulation failure and capacitive coupling. To reduce the incidence of injury by monopolar electrosurgery at laparoscopy, there is a need for advanced technology, such as AEM. In addition, laparoscopic surgeons should be encouraged to study the basic concepts of the biophysics of electrosurgery.

Effect of hydration on the mechanical properties and ion conduction in a polyethylene-b-poly(vinylbenzyl trimethylammonium) anion exchange membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vandiver, Melissa A.; Caire, Benjamin R.; Pandey, Tara P.

Anion exchange m em branes (AEM )are prom ising solid polym er electrolytes utilized in alkalifuelcells and electrochem icalenergy conversion devices.AEM s m ust ef ciently conductions w hile m aintaining chem icaland m echanicalstability undera range ofoperating conditions.The ionicnature ofAEM sleads to stiffand brittle m em branesunderdry conditions w hile athigher hydrations,w ater sorption causes signi cant softening and w eakening of the m em brane.In this w ork,a new polyethylene-b-poly(vinylbenzyltrim ethylam m onium ) polym er (70 kg/m ol) w as cast into large (300 cm 2),thin (127 3 m ) m em branes.These m em branes exhibitedmore » im proved elasticity over previously tested AEM s,m inim aldim ensional sw elling,and m oderate ionic conductivity (57 2 m S/cm at 50 °C,95% RH in the brom ide form ).Extensional testing indicated a 95% reduction in Young's m odulus betw een dry and hydrated states.Furtherinvestigation ofthe com plex m odulusasa function ofhydration,by dynam ic m echanical analysis,revealed a sharp decrease in m odulusbetw een dry and hydrated states.M echanicalsoftening w as reversible,but the location ofthe transition displayed hysteresis betw een hum idi cation and dehum idi cation.Conductivity increased after m em brane softening;suggesting bulk m echanicalpropertiescan identify thehydration levelrequired forim proved ion transport.Understanding the relationship betw een ion conduction and m echanical properties w illhelp guide AEM developm ent and identify operating conditions for sustained perform ance.« less

Aquifers and Their Tectonic Connectivity in Flood Basalts Using AEM

NASA Astrophysics Data System (ADS)

Chandra, S.; Auken, E.; Sonkamble, S.; Maurya, P. K.; Ahmed, S.; Clausen, O. R.; Verma, S. K.

2016-12-01

Aquifers, the major freshwater storage providing water for human consumption, agriculture, industry and groundwater-dependent ecosystems, are subjected to increasing stress resulting into drying up of large number of wells in major parts of world. The climate change with erratic rainfall pattern and increasing temperature enhances the rate of evapotranspiration causing reduction in groundwater recharge as well as enhancement in the groundwater withdrawal. Not only the wells, but also springs, ponds and non glacial rivers, mostly fed by base flow during non-monsoon periods, also go dry during droughts. Water crisis is very severe in the basaltic and hard rock areas in India where the weathered zone, principal aquifer, has almost dried up and the water is mostly confined within the underlying vesicular and weathered-fractured basalts, and occasionally within green bole beds. The paper presents results from Basaltic hard rock terrains in India based on integrated geophysical surveys including airborne electromagnetic (AEM) and airborne magnetic methods. Due to good resistivity contrasts, AEM results showed strong signatures of multiple basaltic flows, their alterations and associated major intertrappeans. In combination with ground geophysics, geological and borehole information, AEM was found to be very effective in mapping the multiple flows, Gondwana and basaltic interface, and inter- and infra-trappeans (Figure 1). In addition to the basaltic flows, we could map the tectonic groundwater pathways, which is a completely new knowledge. The tectonic pathways connect different aquifers (water saturated vesicular basalt) located in various flows. The results demonstrate that the AEM is very effective for groundwater prospecting in basalts and in delineating suitable recharge zones to create strategic groundwater reserves.

Recent Advances in Laplace Transform Analytic Element Method (LT-AEM) Theory and Application to Transient Groundwater Flow

NASA Astrophysics Data System (ADS)

Kuhlman, K. L.; Neuman, S. P.

2006-12-01

Furman and Neuman (2003) proposed a Laplace Transform Analytic Element Method (LT-AEM) for transient groundwater flow. LT-AEM applies the traditionally steady-state AEM to the Laplace transformed groundwater flow equation, and back-transforms the resulting solution to the time domain using a Fourier Series numerical inverse Laplace transform method (de Hoog, et.al., 1982). We have extended the method so it can compute hydraulic head and flow velocity distributions due to any two-dimensional combination and arrangement of point, line, circular and elliptical area sinks and sources, nested circular or elliptical regions having different hydraulic properties, and areas of specified head, flux or initial condition. The strengths of all sinks and sources, and the specified head and flux values, can all vary in both space and time in an independent and arbitrary fashion. Initial conditions may vary from one area element to another. A solution is obtained by matching heads and normal fluxes along the boundary of each element. The effect which each element has on the total flow is expressed in terms of generalized Fourier series which converge rapidly (<20 terms) in most cases. As there are more matching points than unknown Fourier terms, the matching is accomplished in Laplace space using least-squares. The method is illustrated by calculating the resulting transient head and flow velocities due to an arrangement of elements in both finite and infinite domains. The 2D LT-AEM elements already developed and implemented are currently being extended to solve the 3D groundwater flow equation.

Towards high conductivity in anion-exchange membranes for alkaline fuel cells.

PubMed

Li, Nanwen; Guiver, Michael D; Binder, Wolfgang H

2013-08-01

Quaternized poly(2,6-dimethylphenylene oxide) materials (PPOs) containing clicked 1,2,3-triazoles were first prepared through Cu(I) -catalyzed "click chemistry" to improve the anion transport in anion-exchange membranes (AEMs). Clicked 1,2,3-triazoles incorporated into AEMs provided more sites to form efficient and continuous hydrogen-bond networks between the water/hydroxide and the triazole for anion transport. Higher water uptake was observed for these triazole membranes. Thus, the membranes showed an impressive enhancement of the hydroxide diffusion coefficient and, therefore, the anion conductivities. The recorded hydroxide conductivity was 27.8-62 mS cm(-1) at 20 °C in water, which was several times higher than that of a typical PPO-based AEM (TMA-20) derived from trimethylamine (5 mS cm(-1) ). Even at reduced relative humidity, the clicked membrane showed superior conductivity to a trimethylamine-based membrane. Moreover, similar alkaline stabilities at 80 °C in 1 M NaOH were observed for the clicked and non-clicked membranes. The performance of a H2 /O2 single cell assembled with a clicked AEM was much improved compared to that of a non-clicked TMA-20 membrane. The peak power density achieved for an alkaline fuel cell with the synthesized membrane 1a(20) was 188.7 mW cm(-2) at 50 °C. These results indicated that clicked AEM could be a viable strategy for improving the performance of alkaline fuel cells. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Exploring backbone-cation alkyl spacers for multi-cation side chain anion exchange membranes

NASA Astrophysics Data System (ADS)

Zhu, Liang; Yu, Xuedi; Hickner, Michael A.

2018-01-01

In order to systematically study how the arrangement of cations on the side chain and length of alkyl spacers between cations impact the performance of multi-cation AEMs for alkaline fuel cells, a series of polyphenylene oxide (PPO)-based AEMs with different cationic side chains were synthesized. This work resulted in samples with two or three cations in a side chain pendant to the PPO backbone. More importantly, the length of the spacer between cations varied from 3 methylene (-CH2-) (C3) groups to 8 methylene (C8) groups. The highest conductivity, up to 99 mS/cm in liquid water at room temperature, was observed for the triple-cation side chain AEM with pentyl (C5) or hexyl (C6) spacers. The multi-cation AEMs were found to have decreased water uptake and ionic conductivity when the spacer chains between cations were lengthened from pentyl (C5) or hexyl (C6) to octyl (C8) linking groups. The triple-cation membranes with pentyl (C5) or hexyl (C6) groups between cations showed greatest stability after immersion in 1 M NaOH at 80 °C for 500 h.

Integrated interpretation of overlapping AEM datasets achieved through standardisation

NASA Astrophysics Data System (ADS)

Sørensen, Camilla C.; Munday, Tim; Heinson, Graham

2015-12-01

Numerous airborne electromagnetic surveys have been acquired in Australia using a variety of systems. It is not uncommon to find two or more surveys covering the same ground, but acquired using different systems and at different times. Being able to combine overlapping datasets and get a spatially coherent resistivity-depth image of the ground can assist geological interpretation, particularly when more subtle geophysical responses are important. Combining resistivity-depth models obtained from the inversion of airborne electromagnetic (AEM) data can be challenging, given differences in system configuration, geometry, flying height and preservation or monitoring of system acquisition parameters such as waveform. In this study, we define and apply an approach to overlapping AEM surveys, acquired by fixed wing and helicopter time domain electromagnetic (EM) systems flown in the vicinity of the Goulds Dam uranium deposit in the Frome Embayment, South Australia, with the aim of mapping the basement geometry and the extent of the Billeroo palaeovalley. Ground EM soundings were used to standardise the AEM data, although results indicated that only data from the REPTEM system needed to be corrected to bring the two surveys into agreement and to achieve coherent spatial resistivity-depth intervals.

Spacelab Life Sciences 1, development towards successive life sciences flights

NASA Technical Reports Server (NTRS)

Dalton, B. P.; Jahns, G.; Hogan, R.

1992-01-01

A general review is presented of flight data and related hardware developments for Spacelab Life Sciences (SLS) 1 with an eye toward applying this knowledge to projected flight planning. Specific attention is given to the Research Animal Holding Facility (RAHF), the General Purpose Work Station (GPWS), the Small Mass Measuring Instrument (SMMI), and the Animal Enclosure Module (AEM). Preflight and in-flight testing methods are detailed including biocompatibility tests, parametric engineering sensitivity analyses, measurements of environmental parameters, and studies of operational interfaces. Particulate containment is demonstrated for some of the equipment, and successful use of the GPWS, RAHF, AEM, and SMMI are reported. The in-flight data are useful for developing more advanced hardware such as the AEM for SLS flight 2 and the modified RAHF for SLS flight 3.

Delineation of the hydrogeologic framework of the Big Sioux aquifer near Sioux Falls, South Dakota, using airborne electromagnetic data

USGS Publications Warehouse

Valseth, Kristen J.; Delzer, Gregory C.; Price, Curtis V.

2018-03-21

The U.S. Geological Survey, in cooperation with the City of Sioux Falls, South Dakota, began developing a groundwater-flow model of the Big Sioux aquifer in 2014 that will enable the City to make more informed water management decisions, such as delineation of areas of the greatest specific yield, which is crucial for locating municipal wells. Innovative tools are being evaluated as part of this study that can improve the delineation of the hydrogeologic framework of the aquifer for use in development of a groundwater-flow model, and the approach could have transfer value for similar hydrogeologic settings. The first step in developing a groundwater-flow model is determining the hydrogeologic framework (vertical and horizontal extents of the aquifer), which typically is determined by interpreting geologic information from drillers’ logs and surficial geology maps. However, well and borehole data only provide hydrogeologic information for a single location; conversely, nearly continuous geophysical data are collected along flight lines using airborne electromagnetic (AEM) surveys. These electromagnetic data are collected every 3 meters along a flight line (on average) and subsequently can be related to hydrogeologic properties. AEM data, coupled with and constrained by well and borehole data, can substantially improve the accuracy of aquifer hydrogeologic framework delineations and result in better groundwater-flow models. AEM data were acquired using the Resolve frequency-domain AEM system to map the Big Sioux aquifer in the region of the city of Sioux Falls. The survey acquired more than 870 line-kilometers of AEM data over a total area of about 145 square kilometers, primarily over the flood plain of the Big Sioux River between the cities of Dell Rapids and Sioux Falls. The U.S. Geological Survey inverted the survey data to generate resistivity-depth sections that were used in two-dimensional maps and in three-dimensional volumetric visualizations of the Earth resistivity distribution. Contact lines were drawn using a geographic information system to delineate interpreted geologic stratigraphy. The contact lines were converted to points and then interpolated into a raster surface. The methods used to develop elevation and depth maps of the hydrogeologic framework of the Big Sioux aquifer are described herein.The final AEM interpreted aquifer thickness ranged from 0 to 31 meters with an average thickness of 12.8 meters. The estimated total volume of the aquifer was 1,060,000,000 cubic meters based on the assumption that the top of the aquifer is the land-surface elevation. A simple calculation of the volume (length times width times height) of a previous delineation of the aquifer estimated the aquifer volume at 378,000,000 cubic meters; thus, the estimation based on AEM data is more than twice the previous estimate. The depth to top of Sioux Quartzite, which ranged in depth from 0 to 90 meters, also was delineated from the AEM data.

Mining hydrogeological data from existing AEM datasets for mineral Mining

NASA Astrophysics Data System (ADS)

Menghini, Antonio; Viezzoli, Andrea; Teatini, Pietro; Cattarossi, Andrea

2017-04-01

Large amount of existing Airborne Electromagnetic (AEM) data are potentially available all over the World. Originally acquired for mining purposes, AEM data traditionally do not get processed in detail and inverted: most of the orebodies can be easily detected by analyzing just the peak anomaly directly evidenced by voltage values (the so-called "bump detection"). However, the AEM acquisitions can be accurately re-processed and inverted to provide detailed 3D models of resistivity: a first step towards hydrogeological studies and modelling. This is a great opportunity especially for the African continent, where the detection of exploitable groundwater resources is a crucial issue. In many cases, a while after AEM data have been acquired by the mining company, Governments become owners of those datasets and have the opportunity to develop detailed hydrogeological characterizations at very low costs. We report the case in which existing VTEM (Versatile Time Domain Electromagnetic - Geotech Ltd) data, originally acquired to detect gold deposits, are used to improve the hydrogeological knowledge of a roughly 50 km2 pilot-test area in Sierra Leone. Thanks to an accurate processing workflow and an advanced data inversion, based on the Spatially Constrained Inversion (SCI) algorithm, we have been able to resolve the thickness of the regolith aquifer and the top of the granitic-gneiss or greenstone belt bedrock. Moreover, the occurrence of different lithological units (more or less conductive) directly related to groundwater flow, sometimes having also a high chargeability (e.g. in the case of lateritic units), has been detailed within the regolith. The most promising areas to drill new productive wells have been recognized where the bedrock is deeper and the regolith thickness is larger. A further info that was considered in hydrogeological mapping is the resistivity of the regolith, provided that the most permeable layers coincide with the most resistive units. The resistivity model thus produced has allowed us to detect some alignments of conductive dykes, perforating the greenstone belt (made by volcanic Mafic and Ultramafic rocks or Metasedimentary formations), and correlated with the gold mineralization. Moreover, the conductive response of the basal serpentine-chloritized Ultramafic volcanic rocks, has allowed reconstructing the deeper structural features of the area. Therefore, the advantage in re-processing existing AEM data has been twofold, i.e. for both hydrogeological and geological-structural (hence mining) purposes. Concluding, we advocate for re-using of existing AEM datasets covering wide areas in underdeveloped and developing countries in to improve the hydrogeological characterizations of these nations where groundwater resources could cope with need of providing fresh / safe water to the population.

Effect of spaceflight hardware on the skeletal properties of ground control mice

NASA Astrophysics Data System (ADS)

Bateman, Ted; Lloyd, Shane; Dunlap, Alex; Ferguson, Virginia; Simske, Steven; Stodieck, Louis; Livingston, Eric

Introduction: Spaceflight experiments using mouse or rat models require habitats that are specifically designed for the microgravity environment. During spaceflight, rodents are housed in a specially designed stainless steel meshed cage with gravity-independent food and water delivery systems and constant airflow to push floating urine and feces towards a waste filter. Differences in the housing environment alone, not even considering the spaceflight environment itself, may lead to physiological changes in the animals contained within. It is important to characterize these cage differences so that results from spaceflight experiments can be more reliably compared to studies from other laboratories. Methods: For this study, we examined the effect of NASA's Animal Enclosure Module (AEM) spaceflight hardware on the skeletal properties of 8-week-old female C57BL/6J mice. This 13-day experiment, conducted on the ground, modeled the flight experiment profile of the CBTM-01 payload on STS-108, with standard vivarium-housed mice being compared to AEM-housed mice (n = 12/group). Functional differences were compared via mechanical testing, micro-hardness indentation, microcomputed tomography, and mineral/matrix composition. Cellular changes were examined by serum chemistry, histology, quantitative histomorphometry, and RT-PCR. A Student's t-test was utilized, with the level of Type I error set at 95 Results: There was no change in elastic, maximum, or fracture force mechanical properties at the femur mid-diaphysis, however, structural stiffness was -17.5 Conclusions: Housing mice in the AEM spaceflight hardware had minimal effects on femur cortical bone properties. However, trabecular bone at the proximal tibia in AEM mice experi-enced large increases in microarchitecture and mineral composition. Increases in bone density were accompanied by reductions in bone-forming osteoblasts and bone-resorbing osteoclasts, representing a general decline in bone turnover at this site. Serum markers suggest a systemic decline in bone formation. The increase in trabecular bone formation rate is likely a result of the reduced resorptive activity; normal levels of bone resorption in vivarium mice likely removed portions of the bone label that were not removed in the AEM housed mice. This is supported by a greater mineralizing surface in AEM mice, with no change in mineral apposition rate.

Scenario analysis of Agro-Environment measure adoption for soil erosion protection in Sicilian vineyard (Italy)

NASA Astrophysics Data System (ADS)

Novara, Agata; Gristina, Luciano; Fantappiè, Maria; Costantini, Edoardo

2014-05-01

Most of the challenges in designing land use policies that address sustainability issues are inherent to the concept of Agro-Environmental Measures (AEM). Researchers, farmers and mainly policy makers need to evaluate the impact of new and existing policies for soil protection. In Europe, farmers commit themselves, for a minimum period of at least five years, to adopt environmentally-friendly farming techniques that undergone legal obligations. On the other hand, farmers receive payments that provide compensation for additional costs and income foregone resulting from applying those environmentally friendly farming practices in line with the stipulations of agri-environment contracts. In this context we prospect scenarios on soil erosion variations in a detailed case study after the application of Agro-Environmental Measures (AEM). The study area is located in the South part of Sicily. In a district area of 11,588 ha, 35.5 % is devoted to vineyard cultivation, 32.2 % is arable land and only 11.1 % cultivated to olive grow. 2416 ha are urbanized areas and other less important crops. A paired-site approach was chosen to study the difference in soil organic carbon stocks after AEM adoption, following criteria based on Conteh (1999) also applied in several research studies. For the purpose of comparison, the members of a paired site were selected to be similar with respect to the type of soil, slope, elevation, and drainage, but not to AEM. The comparisons were made between adjacent patches of land with different AEM, and a known history of land use and management. 100 paired sites (two adjacent plots) were chosen and three soil samples (0-30 cm depth) were collected in each plot (600 soil samples). The rainfall erosivity (R) factor (Mj mm ha-1 hour-1 year-1) was estimated with the formula specifically proposed for Sicily by Ferro and coauthors in 1999. The soil erodibility factor (K, in tons hour MJ-1 mm-1) was mapped on the base of soil texture and soil organic carbon content of the topsoil (averaged on the first 50 cm of soil depth) with the table published by Stone and Hilborn (2012). The slope-length and slope gradient (LS) factors were derived from the Digital Terrain Model of Sicily (20 x 20 m) using the formulas proposed by Wischmeier and Smith (1978), and revised by McCool et al. (1987 and 1989). The C factor were applied according previous studies in the same area and ranged among 0.22 and 0.12 and less than 0.10 using permanent species able to reduce erosion rate up to 90% (Gristina et al., 2006; Novara et al. 2011). The scenario analysis of the soil erosion reduction after the adoption of AEM could be used by policy makers as a base for the evaluation of the Payment for Ecosystem Service (PES) to be paid to farmers through the future Agro-Ecosystem measures incentives. Gristina, L., Bagarello, V., Ferro, V., Poma, I., 2006. Cover and management factor for Sicilian vineyard systems. In: 14th International Soil conservation Organization Conference—Water Management and Soil Conservation in Semi-arid Environments, 14-19 May 2006, Marrakech, Marocco (ISCO2006), pp. 1-4. A Novara, L Gristina, SS Saladino, A Santoro, A Cerda 2011 Soil erosion assessment on tillage and alternative soil managements in a Sicilian vineyard. Soil and Tillage Research 117, 140-147

Workplace injuries in Fiji: a population-based study (TRIP 7).

PubMed

Reddy, R; Kafoa, B; Wainiqolo, I; Kool, B; Gentles, D; McCaig, E; Ameratunga, S

2013-06-01

Workplace injury rates in low and middle-income countries are known to be high. Contemporary data on this topic from Pacific Island countries and territories are scant. To describe the epidemiology of fatal and hospitalized workplace injuries in Fiji using a population-based trauma registry. An analysis of data from a prospective population-based surveillance registry investigated the characteristics associated with workplace injuries resulting in death or hospital admission among people aged 15 years and older in Viti Levu, the largest island in the Republic of Fiji, from October 2005 to September 2006. Incidence rates were calculated using denominator data from the 2004-05 Fiji Employment Survey. One hundred and eighty-nine individuals met the study eligibility criteria (including nine deaths). This corresponded to annual injury-related hospitalization and death rates of 73.4 and 3.7 per 100 000 workers, respectively. Males accounted for 95% of injuries, and hospitalization rates were highest among those aged 15-29 years (33 per 100 000 workers). Fijian and Indian workers had similar rates of admission to hospital (38.3 and 31.8 per 100 000 workers, respectively). Fractures (40%) and 'cuts/bites/open wounds' (32%) were the commonest types of injury while 'being hit by a person or object' (34%), falls (27%) and 'cutting or piercing' injuries (27%) were the commonest mechanisms. Overall, 7% of injuries were deemed intentional. Acknowledging the likely underestimation of the overall burden of workplace injuries, these findings support the need to identify context-specific risk factors and effective approaches to preventing workplace injuries in Fiji.

Mapping the Fresh-Salt Water Interaction in the Coastal Zone Using High Resolution Airborne Electromagnetics

NASA Astrophysics Data System (ADS)

Auken, E.; Pedersen, J. B. B.; Christiansen, A. V.; Foged, N.; Schaars, F.; Rolf, H.

2016-12-01

During the last decade airborne electromagnetics (AEM) and the accompanying data processing and inversion algorithms have undergone huge developments in terms of technology, costs, and reliability. This has expanded the scope of AEM from mainly mineral exploration to geotechnical applications and groundwater resource mapping. In this abstract we present a case with generally applicable results where AEM is used to map saltwater intrusion as well as outflow of fresh water to the sea. The survey took place on the Dutch coast in 2011 and is composed of a detailed inland coastal mapping as well as lines extending kilometres into the North Sea. It adds further complications that the area has a dense infrastructure and rapid varying dune topography causing the need for cautious data processing. We use the high resolution AEM system SkyTEM and data processing and inversion in the Aarhus Workbench. On the inland side, the results show a high resolution image of the fresh water interface and the interaction with clay layers acting as barriers. On the sea side they show a picture of freshwater plumes being pushed several hundred meters under the sea. The last mentioned information was actually the main purpose of the survey as this information could hardly be obtained by other methods and it is decisive for the total water balance of the system. The case shows an example of an AEM survey resulting in a high resolution image of the entire coastal zone. The technology is applicable in all coastal zones in the world and if applied it would lead to much improved management of the water resources in these landscapes.

The Hole-Count Test Revisited: Effects of Test Specimen Thickness

NASA Technical Reports Server (NTRS)

Lyman, C. E.; Ackland, D. W.; Williams, D. B.; Goldstein, J. I.

1989-01-01

For historical reasons the hole count, an important performance test for the Analytical Electron Microscope (AEM), is somewhat arbitrary yielding different numbers for different investigators. This was not a problem a decade ago when AEM specimens were often bathed with large fluxes of stray electrons and hard x rays. At that time the presence or absence of a thick Pt second condenser (C2) aperture could be detected by a simple comparison of the x-ray spectrum taken 'somewhere in the hole' with a spectrum collected on a 'typical thickness' of Mo or Ag foil. A high hole count of about 10-20% indicated that the electron column needed modifications; whereas a hole count of 1-2% was accepted for most AEM work. The absolute level of the hole count is a function of test specimen atomic number, overall specimen shape, and thin-foil thickness. In order that equivalent results may be obtained for any AEM in any laboratory in the world, this test must become standardized. The hole-count test we seek must be as simpl and as nonsubjective as the graphite 0.344nm lattice-line-resolution test. This lattice-resolution test spurred manufacturers to improve the image resolution of the TEM significantly in the 1970s and led to the even more stringent resolution tests of today. A similar phenomenon for AEM instruments would be welcome. The hole-count test can also indicate whether the spurious x-ray signal is generated by high-energy continuum x rays (bremsstrahlung) generated in the electron column (high K-line to L-line ratio) or uncollimated electrons passing through or around the C2 aperture (low K/L ratio).

3D Airborne Electromagnetic Inversion: A case study from the Musgrave Region, South Australia

NASA Astrophysics Data System (ADS)

Cox, L. H.; Wilson, G. A.; Zhdanov, M. S.; Sunwall, D. A.

2012-12-01

Geophysicists know and accept that geology is inherently 3D, and is resultant from complex, overlapping processes related to genesis, metamorphism, deformation, alteration, weathering, and/or hydrogeology. Yet, the geophysics community has long relied on qualitative analysis, conductivity depth imaging (CDIs), 1D inversion, and/or plate modeling. There are many reasons for this deficiency, not the least of which has been the lack of capacity for historic 3D AEM inversion algorithms to invert entire surveys so as to practically affect exploration decisions. Our recent introduction of a moving sensitivity domain (footprint) methodology has been a paradigm shift in AEM interpretation. The basis of this method is that one needs only to calculate the responses and sensitivities for that part of the 3D earth model that is within the AEM system's sensitivity domain (footprint), and then superimpose all sensitivity domains into a single, sparse sensitivity matrix for the entire 3D earth model which is then updated in a regularized inversion scheme. This has made it practical to rigorously invert entire surveys with thousands of line kilometers of AEM data to mega-cell 3D models in hours using multi-processor workstations. Since 2010, over eighty individual projects have been completed for Aerodat, AEROTEM, DIGHEM, GEOTEM, HELITEM, HoisTEM, MEGATEM, RepTEM, RESOLVE, SkyTEM, SPECTREM, TEMPEST, and VTEM data from Australia, Brazil, Canada, Finland, Ghana, Peru, Tanzania, the US, and Zambia. Examples of 3D AEM inversion have been published for a variety of applications, including mineral exploration, oil sands exploration, salinity, permafrost, and bathymetry mapping. In this paper, we present a comparison of 3D inversions for SkyTEM, SPECTREM, TEMPET and VTEM data acquired over the same area in the Musgrave region of South Australia for exploration under cover.

Collaborative Research and Development (CR&D). Delivery Order 0051: Atomic Scale Transmission Electron Microscope Image Modeling and Application to Semiconductor Heterointerface Characterization

DTIC Science & Technology

2008-01-01

information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD...microscopy ( AEM ), to characterize a variety of III-V semiconductor thin films. The materials investigated include superlattices based on the InAs- GaSb...technique. TEM observations were performed using a Philips-CM 200 FEG transmission electron microscope equipped with a field emission gun, operated at an

Ground and space flight experiments of the effects of light, sound and/or temperature on animals

NASA Technical Reports Server (NTRS)

Holley, Daniel C.; Du, Vince; Erikson, Jill; Gott, Jack; Hinchcliffe, Heather; Mele, Gary; Moeller, Karen; Nguyen, Tam; Okumura, Sarah; Robbins, Mark

1994-01-01

Papers on the following topics are presented: (1) rat long term habitability and breeding under low light intensity (5 lux); (2) effects of low light intensity on the rat circadian system; (3) effects of sound/noise on the circadian system of rats; (4) temperature related problems involving the animal enclosure modules (AEM) lighting system; and (5) NASA AEM filter test 92/93 (Rats).

Exploiting EMI Signals During Active Transmission

DTIC Science & Technology

2010-08-12

Surveys) fixed wing airborne EM system. (Center) AeroTEM (AeroQuest Surveys) helicopter-based airborne time-domain EM system, (Right) VTEM ( GeoTech Ltd...Center) AeroTEM (AeroQuest Surveys) helicopter-based airborne time-domain EM system, (Right) VTEM ( GeoTech Ltd.) helicopter-borne AEM system. All three...systems such as the UTEM (Lamontange Geophysics) and the SPECTREM AEM systems. Geotech Ltd. uses a complicated waveform which has been optimized to

Carbonate and Bicarbonate Ion Transport in Alkaline Anion Exchange Membranes

DTIC Science & Technology

2013-06-25

membranes (AEMs) are being developed for potential use in fuel cell systems which include portable power applications. In a fuel cell , these membranes...Alkaline Anion Exchange Membranes Report Title ABSTRACT Anion exchange membranes (AEMs) are being developed for potential use in fuel cell systems which...include portable power applications. In a fuel cell , these membranes transport hydroxide ions from the cathode to the anode. If carbon dioxide is

Highly stable pyridinium-functionalized cross-linked anion exchange membranes for all vanadium redox flow batteries

NASA Astrophysics Data System (ADS)

Zeng, L.; Zhao, T. S.; Wei, L.; Zeng, Y. K.; Zhang, Z. H.

2016-11-01

It has recently been demonstrated that the use of anion exchange membranes (AEMs) in vanadium redox flow batteries (VRFBs) can reduce the migration of vanadium ions through the membrane due to the Donnan exclusion effect among the positively charged functional groups and vanadium ions. However, AEMs are plagued by low chemical stability in harsh chemical environments. Here we propose and fabricate a pyridinium-functionalized cross-linked AEM for VRFBs. The pyridinium-functionalized bromomethylated poly (2,6-dimethyl-1,4-phenylene oxide) exhibits a superior chemical stability as a result of the strengthened internal cross-linking networks and the chemical inertness of the polymer backbone. Therefore, the membrane exhibits littler decay in a harsh environment for 20 days during the course of an ex situ immersion test. A cycling test also demonstrates that the VRFB assembled with the membrane enable to retain 80% of the initial discharge capacity over 537 cycles with a capacity decay rate of 0.037% cycle-1. Meanwhile, the membrane also shows a low vanadium permeability and a reasonably high conductivity in supporting electrolytes. Hence, all the measurements and performance tests reported in this work suggest that the membrane is a promising AEM for redox flow batteries to achieve excellent cycling stability and superior cell performance.

Recyclable cross-linked anion exchange membrane for alkaline fuel cell application

NASA Astrophysics Data System (ADS)

Hou, Jianqiu; Liu, Yazhi; Ge, Qianqian; Yang, Zhengjin; Wu, Liang; Xu, Tongwen

2018-01-01

Cross-linking can effectively solve the conductivity-swelling dilemma in anion exchange membranes (AEMs) but will generate solid wastes. To address this, we developed an AEM cross-linked via disulfide bonds, bearing quaternary ammonium groups, which can be easily recycled. The membrane (RC-QPPO) with IEC of 1.78 mmol g-1, when cross-linked, showed enhanced mechanical properties and good hydroxide conductivity (24.6 mS cm-1 at 30 °C). Even at higher IEC value (2.13 mmol g-1), it still has low water uptake, low swelling ratio and delivers a peak power density of 150 mW cm-2 at 65 °C. Exploiting the formation of disulfide bonds from -SH groups, the membrane can be readily cross-linked in alkaline condition and recycled by reversibly breaking disulfide bonds with dithiothreitol (DTT). The recycled membrane solution can be directly utilized to cast a brand-new AEM. By washing away the residual DTT with water and exposure to air, it can be cross-linked again and this process is repeatable. During the recycling and cross-linking processes, the membrane showed a slight IEC decrease of 5% due to functional group degradation. The strategy presented here is promising in enhancing AEM properties and reducing the impact of artificial polymers on the environment.

Effectiveness of incentives for agri-environment measure in Mediterranean degraded and eroded vineyards

NASA Astrophysics Data System (ADS)

Galati, Antonino; Gristina, Luciano; Crescimanno, Maria; Barone, Ettore; Novara, Agata

2015-04-01

The evaluation of the economic damage caused by soil erosion assumes great importance. It serves to increase awareness of the problem among farmers and policy makers. Moreover, it can promote the implementation of conservative measures at the field and basin level by spurring the development of more sustainable soil management practices. In the present study we have developed a new approach to evaluate the incentive for the adoption of Agri-Environment Measure (AEM) in Mediterranean degraded and eroded vineyards. In order to estimate this incentive, the replacement cost and the loss of income are calculated under two different soil management such as Conventional Tillage (CT) and Cover crop (AEM). Our findings show that the incentive could range between the loss of income due to AEM adoption and ecosystem service benefit (RCCT - RC AEM). In the case of study the incentive ranged between 315 € ha-1 (loss of income) and 1,087.86 € ha-1 (Ecosystem service benefit). Within this range, the incentive amount is determined according to efficiency criteria taking into account the morphological conditions of the territory in which operate the farms. Moreover, a conceptual model on the public spending efficiency has been developed to allocate the incentives where the economic return in term of ecosystem service is higher.

Electrodialytic 2-compartment cells for emerging organic contaminants removal from effluent.

PubMed

Ferreira, Ana Rita; Couto, Nazaré; Guedes, Paula; Pinto, Joana; Mateus, Eduardo P; Ribeiro, Alexandra B

2018-04-27

The present work discusses the efficiency of the electrodialytic (ED) process to remove emerging organic contaminants (EOCs) from effluent. The ED process was carried out in a cell of two-compartments (2 C-cell) with effluent in either the anode or cathode compartment, separated from the electrolyte compartment through an anion or a cation exchange membrane (AEM and CEM, respectively). As effluent destination might be soil irrigation, and having in mind the nutrient recycling, phosphorus was also monitored in the process. The ED removals showed to be dependent of EOCs characteristics and cell design. Removals were higher when using an AEM (60-72%) than a CEM (8-63%), except for caffeine when the effluent was placed in the cathode, that did not show any removal. When using an AEM with the effluent placed in the anode compartment, all the EOCs (including caffeine) were removed between 57-72%, mainly through electrodegradation phenomena. Regarding phosphorus, a polarity switch may be done to a 2 C-cell with a AEM, depending on the effluent final use. This technology is still in its first steps and, in both cases, further optimization of ED parameters is needed. Still, this technological innovation and cross-cutting research envisages the promotion of economic, social and environmental benefits. Copyright © 2018 Elsevier B.V. All rights reserved.

STS-135 crew during AEM (Animal Enclosure Module) training

NASA Image and Video Library

2011-03-25

JSC2011-E-029133 (25 March 2011) --- STS-135 crew members participate in an Animal Enclosure Module (AEM) training session in the Jake Garn Simulation and Training Facility at NASA's Johnson Space Center. Pictured from the right are NASA astronauts Chris Ferguson, commander; Sandy Magnus and Rex Walheim, both mission specialists. STS-135 is planned to be the final mission of the space shuttle program. Photo credit: NASA or National Aeronautics and Space Administration

Effect of the type of ion exchange membrane on performance, ion transport, and pH in biocatalyzed electrolysis of wastewater.

PubMed

Rozendal, R A; Sleutels, T H J A; Hamelers, H V M; Buisman, C J N

2008-01-01

Previous studies have shown that the application of cation exchange membranes (CEMs) in bioelectrochemical systems running on wastewater can cause operational problems. In this paper the effect of alternative types of ion exchange membrane is studied in biocatalyzed electrolysis cells. Four types of ion exchange membranes are used: (i) a CEM, (ii) an anion exchange membrane (AEM), (iii) a bipolar membrane (BPM), and (iv) a charge mosaic membrane (CMM). With respect to the electrochemical performance of the four biocatalyzed electrolysis configurations, the ion exchange membranes are rated in the order AEM > CEM > CMM > BPM. However, with respect to the transport numbers for protons and/or hydroxyl ions (t(H/OH)) and the ability to prevent pH increase in the cathode chamber, the ion exchange membranes are rated in the order BPM > AEM > CMM > CEM.

Surface water-groundwater exchange in transitional coastal environments by airborne electromagnetics: The Venice Lagoon example

NASA Astrophysics Data System (ADS)

Viezzoli, A.; Tosi, L.; Teatini, P.; Silvestri, S.

2010-01-01

A comprehensive investigation of the mixing between salt/fresh surficial water and groundwater in transitional environments is an issue of paramount importance considering the ecological, cultural, and socio-economic relevance of coastal zones. Acquiring information, which can improve the process understanding, is often logistically challenging, and generally expensive and slow in these areas. Here we investigate the capability of airborne electromagnetics (AEM) at the margin of the Venice Lagoon, Italy. The quasi-3D interpretation of the AEM outcome by the spatially constrained inversion (SCI) methodology allows us to accurately distinguish several hydrogeological features down to a depth of about 200 m. For example, the extent of the saltwater intrusion in coastal aquifers and the transition between the upper salt saturated and the underlying fresher sediments below the lagoon bottom are detected. The research highlights the AEM capability to improve the hydrogeological characterization of subsurface processes in worldwide lagoons, wetlands, deltas.

Teratology study of amide derivatives of branched aliphatic carboxylic acids with 4-aminobenzensulfonamide in NMRI mice.

PubMed

Onishi, Yuko; Okada, Akinobu; Noyori, Hiroko; Okamura, Ai; Hen, Naama; Yagen, Boris; Bialer, Meir; Fujiwara, Michio

2013-08-01

Valproic acid (VPA), widely used to treat epilepsy, bipolar disorders, and migraine prophylaxis, is known to cause neural tube and skeletal defects in humans and animals. Aminobenzensulfonamide derivatives of VPA with branched aliphatic carboxylic acids, namely 2-methyl-N-(4-sulfamoyl-phenyl)-pentanamide (MSP), 2-ethyl-N-(4-sulfamoyl-phenyl)-butyramide (ESB), 2-ethyl-4-methyl-N-(4-sulfamoyl-phenyl)-pentanamide (EMSP), and 2-ethyl-N-(4-sulfamoyl-benzyl)-butyramide (ESBB), have shown more potent anticonvulsant activity than VPA in preclinical testing. Here, we investigated the teratogenic effects of these analogous compounds of VPA in NMRI mice. Pregnant NMRI mice were given a single subcutaneous injection of either VPA at 1.8 or 3.6 mmol/kg, or MSP, ESB, EMSP, or ESBB at 1.8, 3.6, or 4.8 mmol/kg on gestation day (GD) 8. Cesarean section was performed on GD 18, and the live fetuses were examined for external and skeletal malformations. Compared with VPA, which induced neural tube defects (NTDs) in fetuses at 1.8 and 3.6 mmol/kg, the analog derivatives induced no NTDs at dose levels up to 4.8 mmol/kg (except for a single case of exencephaly at 4.8 mmol/kg MSP). Skeletal examination showed several abnormalities mainly at the axial skeletal level with VPA at 1.8 mmol/kg. Fused vertebrae and/or fused ribs were also observed with MSP, ESB, EMSP, and ESBB, they were less severe and seen at a lower incidence that those induced by VPA at the same dose level. In addition to exerting more potent preclinical antiepileptic activity, teratology comparison indicates that aminobenzensulfonamide analogs are generally more weakly teratogenic than VPA. © 2013 Wiley Periodicals, Inc.

Applications of the Analytical Electron Microscope to Materials Science

NASA Technical Reports Server (NTRS)

Goldstein, J. I.

1992-01-01

In the last 20 years, the analytical electron microscope (AEM) as allowed investigators to obtain chemical and structural information from less than 50 nanometer diameter regions in thin samples of materials and to explore problems where reactions occur at boundaries and interfaces or within small particles or phases in bulk samples. Examples of the application of the AEM to materials science problems are presented in this paper and demonstrate the usefulness and the future potential of this instrument.

Interplay between water uptake, ion interactions, and conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) anion exchange membrane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandey, Tara P.; Maes, Ashley M.; Sarode, Himanshu N.

We demonstrate that the true hydroxide conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) [ETFE] anion exchange membrane (AEM) is as high as 132 mS cm -1 at 80 °C and 95% RH, comparable to a proton exchange membrane, but with very much less water present in the film. To understand this behaviour we studied ion transport of hydroxide, carbonate, bicarbonate and chloride, as well as water uptake and distribution. Water uptake of the AEM in water vapor is an order of magnitude lower than when submerged in liquid water. In addition 19F pulse field gradient spin echo NMR indicates that theremore » is little tortuosity in the ionic pathways through the film. A complete analysis of the IR spectrum of the AEM and the analyses of water absorption using FT-IR led to conclusion that the fluorinated backbone chains do not interact with water and that two types of water domains exist within the membrane. The reduction in conductivity was measured during exposure of the OH - form of the AEM to air at 95% RH and was seen to be much slower than the reaction of CO 2 with OH - as the amount of water in the film determines its ionic conductivity and at relative wet RHs its re-organization is slow.« less

Assessing the influence of side-chain and main-chain aromatic benzyltrimethyl ammonium on anion exchange membranes.

PubMed

Li, Xiuhua; Nie, Guanghui; Tao, Jinxiong; Wu, Wenjun; Wang, Liuchan; Liao, Shijun

2014-05-28

3,3'-Di(4″-methyl-phenyl)-4,4'-difluorodiphenyl sulfone (DMPDFPS), a new monomer with two pendent benzyl groups, was easily prepared by Suzuki coupling reaction in high yield. A series of side-chain type ionomers (PAES-Qs) containing pendant side-chain benzyltrimethylammonium groups, which linked to the backbone by alkaline resisting conjugated C-C bonds, were synthesized via polycondensation, bromination, followed by quaternization and alkalization. To assess the influence of side-chain and main-chain aromatic benzyltrimethylammonium on anion exchange membranes (AEMs), the main-chain type ionomers (MPAES-Qs) with the same backbone were synthesized following the similar procedure. GPC and (1)H NMR results indicate that the bromination shows no reaction selectivity of polymer configurations and ionizations of the side-chain type polymers display higher conversions than that of the main-chain type ones do. These two kinds of AEMs were evaluated in terms of ion exchange capacity (IEC), water uptake, swelling ratio, λ, volumetric ion exchange capacity (IECVwet), hydroxide conductivity, mechanical and thermal properties, and chemical stability, respectively. The side-chain type structure endows AEMs with lower water uptake, swelling ratio and λ, higher IECVwet, much higher hydroxide conductivity, more robust dimensional stability, mechanical and thermal properties, and higher stability in hot alkaline solution. The side-chain type cationic groups containing molecular configurations have the distinction of being practical AEMs and membrane electrode assemblies of AEMFCs.

Interplay between water uptake, ion interactions, and conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) anion exchange membrane.

PubMed

Pandey, Tara P; Maes, Ashley M; Sarode, Himanshu N; Peters, Bethanne D; Lavina, Sandra; Vezzù, Keti; Yang, Yuan; Poynton, Simon D; Varcoe, John R; Seifert, Soenke; Liberatore, Matthew W; Di Noto, Vito; Herring, Andrew M

2015-02-14

We demonstrate that the true hydroxide conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) [ETFE] anion exchange membrane (AEM) is as high as 132 mS cm(-1) at 80 °C and 95% RH, comparable to a proton exchange membrane, but with very much less water present in the film. To understand this behaviour we studied ion transport of hydroxide, carbonate, bicarbonate and chloride, as well as water uptake and distribution. Water uptake of the AEM in water vapor is an order of magnitude lower than when submerged in liquid water. In addition (19)F pulse field gradient spin echo NMR indicates that there is little tortuosity in the ionic pathways through the film. A complete analysis of the IR spectrum of the AEM and the analyses of water absorption using FT-IR led to conclusion that the fluorinated backbone chains do not interact with water and that two types of water domains exist within the membrane. The reduction in conductivity was measured during exposure of the OH(-) form of the AEM to air at 95% RH and was seen to be much slower than the reaction of CO2 with OH(-) as the amount of water in the film determines its ionic conductivity and at relative wet RHs its re-organization is slow.

Community context, acculturation and low-birth-weight risk among Arab Americans: evidence from the Arab-American birth-outcomes study.

PubMed

El-Sayed, Abdulrahman M; Galea, Sandro

2010-02-01

An assessment was made as to whether maternal residence in areas with high Arab-American concentrations, hence with expected low acculturation for this ethnic group, was associated with low-birth-weight (<2500 g) (LBW) risk among Arab-ethnicity mothers (AEM). Data on all births in Michigan from 2000 to 2005 were collected. Bivariate chi(2) tests and multivariable logistic regression models were used to assess the relation between residence in areas with a high Arab-American concentration and risk for LBW among AEM. As a control, analyses were replicated among non-Arab white mothers. Both residence in Dearborn (OR=0.85, 95% CI 0.75 to 0.97), the city with the highest Arab-American concentration in the USA, and residence in 48126 (OR=0.81, 95% CI 0.71 to 0.93), the zip code with the highest concentration of AEM in Dearborn, were associated with a lower risk for LBW compared with residence in the rest of Michigan in multivariable models adjusted for potential confounders. Neither residence in Dearborn nor residence in 48126 was associated with LBW risk among non-Arab white mothers. Residence in areas with high Arab-American concentrations was associated with a lower LBW risk among AEM. Future work should directly measure acculturation, a plausible mediator of this observed relation.

Dienes AEM as an alternative mathematics teaching aid to enhance Indonesian students’ understanding of algebra concept

NASA Astrophysics Data System (ADS)

Soro, S.; Maarif, S.; Kurniawan, Y.; Raditya, A.

2018-01-01

The aim of this study is to find out the effect of Dienes AEM (Algebra Experience Materials) on the ability of understanding concept of algebra on the senior high school student in Indonesia. This research is an experimental research with subject of all high school students in Indonesia. The samples taken were high school students in three provinces namely DKI Jakarta Province, West Java Province and Banten Province. From each province was taken senior high school namely SMA N 9 Bekasi West Java, SMA N 94 Jakarta and SMA N 5 Tangerang, Banten. The number of samples in this study was 114 high school students of tenth grade as experimental class and 115 high school students of tenth grade as control class. Learning algebra concept is needed in learning mathematics, besides it is needed especially to educate students to be able to think logically, systematically, critically, analytically, creatively, and cooperation. Therefore in this research will be developed an effective algebra learning by using Dienes AEM. The result of this research is that there is a significant influence on the students’ concept comprehension ability taught by using Dienes AEM learning as an alternative to instill the concept of algebra compared to the students taught by conventional learning. Besides, the students’ learning motivation increases because students can construct the concept of algebra with props.

Interplay between water uptake, ion interactions, and conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) anion exchange membrane

DOE PAGES

Pandey, Tara P.; Maes, Ashley M.; Sarode, Himanshu N.; ...

2014-12-23

We demonstrate that the true hydroxide conductivity in an e-beam grafted poly(ethylene-co-tetrafluoroethylene) [ETFE] anion exchange membrane (AEM) is as high as 132 mS cm -1 at 80 °C and 95% RH, comparable to a proton exchange membrane, but with very much less water present in the film. To understand this behaviour we studied ion transport of hydroxide, carbonate, bicarbonate and chloride, as well as water uptake and distribution. Water uptake of the AEM in water vapor is an order of magnitude lower than when submerged in liquid water. In addition 19F pulse field gradient spin echo NMR indicates that theremore » is little tortuosity in the ionic pathways through the film. A complete analysis of the IR spectrum of the AEM and the analyses of water absorption using FT-IR led to conclusion that the fluorinated backbone chains do not interact with water and that two types of water domains exist within the membrane. The reduction in conductivity was measured during exposure of the OH - form of the AEM to air at 95% RH and was seen to be much slower than the reaction of CO 2 with OH - as the amount of water in the film determines its ionic conductivity and at relative wet RHs its re-organization is slow.« less

Remarkable recovery in an infant presenting with extensive perinatal cervical cord injury.

PubMed

Ul Haq, Israr; Gururaj, A K

2012-12-10

Cervical-cord damage is a complication of a difficult delivery, and results in spinal shock with flaccidity progressing to spastic paralysis. Conventionally, outlook for such patients is extremely poor and most will recover only slightly from quadriplegia and autonomic dysfunction. Here, we report a case in which the extent of damage considerably contrasted with the outcome and recovery. A full-term baby girl born by difficult vaginal delivery displayed bilateral flaccid paralysis of the lower limbs with absent spontaneous movements, weakness of both upper limbs, hyporeflexia in all limbs and axial hypotonia. MRI of cervicothoracic spine exhibited raised signal intensity in the dorsal aspects of C7 to T1 signifying myelopathy. MRI at 4 months revealed a near-total transection of the cervical cord. However, at 6 months, the child could move all lower limbs independently with a marked increase in power. There was no spasticity, wasting or incontinence. Reflexes had also returned.

STS-135 crew during AEM (Animal Enclosure Module) training

NASA Image and Video Library

2011-03-25

JSC2011-E-029131 (25 March 2011) --- STS-135 crew members participate in an Animal Enclosure Module (AEM) training session in the Jake Garn Simulation and Training Facility at NASA's Johnson Space Center. Pictured on the right (front to back) are NASA astronauts Chris Ferguson, commander; Sandy Magnus and Rex Walheim, both mission specialists; along with Doug Hurley (left foreground), pilot. STS-135 is planned to be the final mission of the space shuttle program. Photo credit: NASA or National Aeronautics and Space Administration

STS-135 crew during AEM (Animal Enclosure Module) training

NASA Image and Video Library

2011-03-25

JSC2011-E-029132 (25 March 2011) --- STS-135 crew members participate in an Animal Enclosure Module (AEM) training session in the Jake Garn Simulation and Training Facility at NASA's Johnson Space Center. Pictured from the left (facing camera) are NASA astronauts Rex Walheim and Sandy Magnus, both mission specialists; and Chris Ferguson, commander; along with Doug Hurley (right foreground), pilot. STS-135 is planned to be the final mission of the space shuttle program. Photo credit: NASA or National Aeronautics and Space Administration

The AEMS (Analysis of Electrical and Mechanical Systems) Project in Applied Mathematics at Carnegie-Mellon University.

DTIC Science & Technology

1982-12-01

Nishizeki 0. Wyler J. M. Greenberg W. Noll Z. Zener H. J. Greenberg J. J. Oravec 5 IV. History of the AENIS Project (1950-1960) Prior to the second...of Professor Herbert Greenberg they drafted a proposal for a research project. The goal of this project was not only to solve certain research...active program in wave research was continued by Professors MacCamy, Mizel, and Greenberg . Their work has directly related to the AEMS work in the

Response to comments by Adam Smiarowski and Shane Mulè on: Christensen, N., and Lawrie, K., 2012. Resolution analyses for selecting an appropriate airborne electromagnetic (AEM) system, Exploration Geophysics, 43, 213-227

NASA Astrophysics Data System (ADS)

Christensen, Niels B.; Lawrie, Ken

2015-06-01

We analyse and compare the resolution improvement that can be obtained from including x-component data in the inversion of AEM data from the SkyTEM and TEMPEST systems. Except for the resistivity of the bottom layer, the SkyTEM system, even without including x-component data, has the better resolution of the parameters of the analysed models.

Crosslinked anion exchange membranes with primary diamine-based crosslinkers for vanadium redox flow battery application

NASA Astrophysics Data System (ADS)

Cha, Min Suc; Jeong, Hwan Yeop; Shin, Hee Young; Hong, Soo Hyun; Kim, Tae-Ho; Oh, Seong-Geun; Lee, Jang Yong; Hong, Young Taik

2017-09-01

A series of polysulfone-based crosslinked anion exchange membranes (AEMs) with primary diamine-based crosslinkers has been prepared via simple a crosslinking process as low-cost and durable membranes for vanadium redox flow batteries (VRFBs). Chloromethylated polysulfone is used as a precursor polymer for crosslinked AEMs (CAPSU-x) with different degrees of crosslinking. Among the developed AEMs, CAPSU-2.5 shows outstanding dimensional stability and anion (Cl-, SO42-, and OH-) conductivity. Moreover, CAPSU-2.5 exhibits much lower vanadium ion permeability (2.72 × 10-8 cm2 min-1) than Nafion 115 (2.88 × 10-6 cm2 min-1), which results in an excellent coulombic efficiency of 100%. The chemical and operational stabilities of the membranes have been investigated via ex situ soaking tests in 0.1 M VO2+ solution and in situ operation tests for 100 cycles, respectively. The excellent chemical, physical, and electrochemical properties of the CAPSU-2.5 membrane make it suitable for use in VRFBs.

Rodent growth, behavior, and physiology resulting from flight on the Space Life Sciences-1 mission

NASA Technical Reports Server (NTRS)

Jahns, G.; Meylor, J.; Fast, T.; Hawes, N.; Zarow, G.

1992-01-01

A rodent-based spaceflight study is conducted to investigate physiological changes in rats vs humans and the effects of changes in the design of the Research Animal Holding Facility (RAHF) and the Animal Enclosure Module (AEM). Rats were housed in the AEM and the RAHF, and controls were kept in identical flight hardware on earth subjected to the same flight-environmental profile. Biosamples and organ weights are taken to compare the rats before and after flight, and food/water intake are also compared. Weight gain, body weight, and food consumptions in the flight rats are significantly lower than corresponding values for the control subjects. Flight rats tend to have smaller postexperiment spleens and hearts, and flight rats consumed more water in the AEM than in the RAHF. The rodents' behavior is analogous to humans with respect to physiological and reconditioning effects, showing that the rat is a good model for basic research into the effects of spaceflight on humans.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ertem, S. Piril; Caire, Benjamin R.; Tsai, Tsung-Han

Anion exchange membranes (AEMs) are a promising class of materials for applications that require selective ion transport, such as fuel cells, water purification, and electrolysis devices. Studies of structure–morphology–property relationships of ion-exchange membranes revealed that block copolymers exhibit improved ion conductivity and mechanical properties due to their microphase-separated morphologies with well-defined ionic domains. While most studies focused on symmetric diblock or triblock copolymers, here, the first example of a midblock quaternized pentablock AEM is presented. A symmetric ABCBA pentablock copolymer was functionalized to obtain a midblock brominated polymer. Solution cast films were then quaternized to obtain AEMs with resulting ionmore » exchange capacities (IEC) ranging from 0.4 to 0.9 mmol/g. Despite the relatively low IEC, the polymers were highly conductive (up to 60 mS/cm Br2 at 90 8C and 95%RH) with low water absorption (<25 wt %) and maintained adequate mechanical properties in both dry and hydrated conditions. Xray scattering and transmission electron microscopy (TEM) revealed formation of cylindrical non-ionic domains in a connected ionic phase.« less

77 FR 32400 - Fenamidone; Pesticide Tolerance; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

...., of the preamble, the text correctly listed the tolerance level for the commodity ``strawberry'' at 0... the tolerance level for ``strawberry'' at 0.15. This technical amendment corrects that error. III. Why... revising the entry for ``Strawberry'' in paragraph (d) to read as follows: Sec. [emsp14]180.579 Fenamidone...

Sleep and sleepiness of pilots operating long-range airplane emergency medical missions.

PubMed

Amann, Ulrike; Holmes, Alex; Caldwell, John; Hilditch, Cassie

2014-09-01

Airplane emergency medical services (AEMS) operators use fixed-wing airplanes to undertake rapid response, round-the-clock medical transport missions. This paper explores the structure of long-range, multileg AEMS missions and the sleep and sleepiness of the pilots who work them. During nine long-range AEMS missions, pilots kept a sleep and sleepiness logbook and wore a wrist activity monitor to evaluate the timing of sleep/wake. Missions had a mean duration of 20 h 00 min ± 2 h 39 min, involved two to four flight legs, and were crewed by three or four pilots who rotated between operating and sleeping in curtained-off bunks. The pilots obtained a mean of 15 h 26 min ± 4 h 51 min and 7 h 54 min ± 1 h 33 min of sleep in the 48 h and 24 h prior to checking in for duty, respectively. During missions, a mean of 3 h 33 min ± 1 h 46 min of sleep was taken, usually across two in-flight sleep periods. Karolinska Sleepiness Scores (KSS) at top of climb and top of descent were typically less than 5 ('neither alert nor sleepy'). A small number of individual higher KSS scores were recorded on the longest missions and on flights between 02:00 and 06:00. These findings suggest that despite the long duration, timing, and multileg nature of AEMS missions, it is possible via careful design and management to operate these missions with appropriate levels of pilot alertness.

Sensitivity of airborne geophysical data to sublacustrine permafrost thaw

NASA Astrophysics Data System (ADS)

Minsley, B. J.; Wellman, T. P.; Walvoord, M. A.; Revil, A.

2014-12-01

A coupled hydrogeophysical forward and inverse modeling approach is developed to illustrate the ability of frequency-domain airborne electromagnetic (AEM) data to characterize subsurface physical properties associated with sublacustrine permafrost thaw during lake talik formation. Several scenarios are evaluated that consider the response to variable hydrologic forcing from different lake depths and hydrologic gradients. The model includes a physical property relationship that connects the dynamic distribution of subsurface electrical resistivity based on lithology as well as ice-saturation and temperature outputs from the SUTRA groundwater simulator with freeze/thaw physics. Electrical resistivity models are used to simulate AEM data in order to explore the sensitivity of geophysical observations to permafrost thaw. Simulations of sublacustrine talik formation over a 1000 year period modeled after conditions found in the Yukon Flats, Alaska, are evaluated. Synthetic geophysical data are analyzed with a Bayesian Markov chain Monte Carlo algorithm that provides a probabilistic assessment of geophysical model uncertainty and resolution. Major lithological and permafrost features are well resolved in the examples considered. The subtle geometry of partial ice-saturation beneath lakes during talik formation cannot be resolved using AEM data, but the gross characteristics of sub-lake resistivity models reflect bulk changes in ice content and can be used to determine the presence of a talik. A final example compares AEM and ground-based electromagnetic responses for their ability to resolve shallow permafrost and thaw features in the upper 1-2 m below ground.

Clinical Decision Rules for Diagnostic Imaging in the Emergency Department: A Research Agenda.

PubMed

Finnerty, Nathan M; Rodriguez, Robert M; Carpenter, Christopher R; Sun, Benjamin C; Theyyunni, Nik; Ohle, Robert; Dodd, Kenneth W; Schoenfeld, Elizabeth M; Elm, Kendra D; Kline, Jeffrey A; Holmes, James F; Kuppermann, Nathan

2015-12-01

Major gaps persist in the development, validation, and implementation of clinical decision rules (CDRs) for diagnostic imaging. The objective of this working group and article was to generate a consensus-based research agenda for the development and implementation of CDRs for diagnostic imaging in the emergency department (ED). The authors followed consensus methodology, as outlined by the journal Academic Emergency Medicine (AEM), combining literature review, electronic surveys, telephonic communications, and a modified nominal group technique. Final discussions occurred in person at the 2015 AEM consensus conference. A research agenda was developed, prioritizing the following questions: 1) what are the optimal methods to justify the derivation and validation of diagnostic imaging CDRs, 2) what level of evidence is required before disseminating CDRs for widespread implementation, 3) what defines a successful CDR, 4) how should investigators best compare CDRs to clinical judgment, and 5) what disease states are amenable (and highest priority) to development of CDRs for diagnostic imaging in the ED? The concepts discussed herein demonstrate the need for further research on CDR development and implementation regarding diagnostic imaging in the ED. Addressing this research agenda should have direct applicability to patients, clinicians, and health care systems. © 2015 by the Society for Academic Emergency Medicine.

“Elegant Tool” Delivers Genome-Level Science for Electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keith Arterburn

Now, a ‘disruptive, virtual scientific simulation tool’ delivers a new, genome-level investigation for electrolytes to develop better, more efficient batteries. Dr. Kevin Gering, an Idaho National Laboratory researcher, has developed the Advanced Electrolyte Model (AEM), a copyrighted molecular-based simulation tool that has been scientifically proven and validated using at least a dozen ‘real-world’ physical metrics. Nominated for the 2014 international R&D 100 Award, AEM revolutionizes electrolyte materials selection, optimizing combinations and key design elements to make battery design and experimentation quick, accurate and responsive to specific needs.

AEMS implementation cost study for Boeing 727

NASA Technical Reports Server (NTRS)

Allison, R. L.

1977-01-01

Costs for airline operational implementation of a NASA-developed approach energy management system (AEMS) concept, as applied to the 727 airplane, were determined. Estimated costs are provided for airplane retrofit and for installation of the required DME ground stations. Operational costs and fuel cost savings are presented in a cost-of-ownership study. The potential return on the equipment investment is evaluated using a net present value method. Scheduled 727 traffic and existing VASI, ILS, and collocated DME ground station facilities are summarized for domestic airports used by 727 operators.

STS-135 crew during AEM (Animal Enclosure Module) training

NASA Image and Video Library

2011-03-25

JSC2011-E-029136 (25 March 2011) --- STS-135 crew members participate in an Animal Enclosure Module (AEM) training session in the Jake Garn Simulation and Training Facility at NASA's Johnson Space Center. Pictured on the right (foreground) is NASA astronaut Chris Ferguson, commander. Pictured in the background (from the left) are astronauts Doug Hurley (mostly obscured), pilot; Rex Walheim and Sandy Magnus (partially obscured), both mission specialists. STS-135 is planned to be the final mission of the space shuttle program. Photo credit: NASA or National Aeronautics and Space Administration

CTV, ITV, ETV, PTV: Television and Education in the 1960s.

ERIC Educational Resources Information Center

Distance Education Report, 2000

2000-01-01

Discusses television in the 1960s as a form of communication including commercial television (CTV), public television (PTV), educational television (ETV), and instructional television (ITV). The Educational Media Study Panel (EMSP), an official advisory group to the Commissioner and the U.S. Office of Education, studied the growth of television…

77 FR 69507 - Proposed Model Safety Evaluation for Plant-Specific Adoption of Technical Specifications Task...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-19

..., ``Revise Shutdown Margin Definition To Address Advanced Fuel Designs'' AGENCY: Nuclear Regulatory... Shutdown Margin Definition to Address Advanced Fuel Designs.'' DATES: Comment period expires on December 19... address newer BWR fuel designs, which may be more reactive at shutdown temperatures above 68[emsp14][deg]F...

78 FR 13100 - Models for Plant-Specific Adoption of Technical Specifications Task Force Traveler TSTF-535...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-26

... Definition To Address Advanced Fuel Designs,'' Using the Consolidated Line Item Improvement Process AGENCY...-specific adoption using the Consolidated Line Item Improvement Process (CLIIP). Additionally, the NRC staff..., which may be more reactive at shutdown temperatures above 68[emsp14][deg]F. This STS improvement is part...

Novel mutation of SRD5A2 gene in a patient with 5α-reductase 2 deficiency from India.

PubMed

Shabir, Iram; Marumudi, Eunice; Khurana, Madan L; Khadgawat, Rajesh

2012-10-30

Master N had genital malformation at birth and had bilateral gonads in the labial fold. He was reared as a boy and corrective surgery was done at the age of 4 years and was reassessed at the age of 14 years. His testosterone/dihydrotestosterone (DHT) was 11.8 (reference range <=10). Molecular analysis of SRD5A2 gene indicated the presence of a novel heterozygous missense mutation of p.A52T in exon 1, which was also detected in mother. The father, sister and maternal grandfather were found to have normal SRD5A2 gene sequence. We also detected an intronic (1-2) homozygous T>C transition in patient, whereas both parents were found to have the same transition in heterozygous form. Although 5α-steroid reductase 2 deficiency is an autosomal-recessive disorder, in this case, it appears that there may be a dominant inheritance because only one identified mutation was present which was passed from mother to son.

Assessing different airborne EM systems for delivering information on aquifer geometry and character: A case study from the Musgrave Province South Australia

NASA Astrophysics Data System (ADS)

Munday, T. J.; Ley-Cooper, A. Y.

2012-12-01

When developing their pre-competitive data bases in support of the minerals industry, State and Federal Government agencies in Australia are now looking at the conjunctive use of airborne geophysics. This is particularly so for AEM data sets, which are now being acquired to promote exploration. This reflects a recognition that in the arid regions of Australia development of a given mineral deposit will, in part, be determined by the availability of water to support mining and mineral processing. An emerging trend, linked to the availability of new data processing procedures, sees AEM data now being actively employed for a combination of applications linked to minerals exploration including geological mapping, aquifer characterization and groundwater assessment. New surveys are being commissioned with attention being given as to whether AEM systems are capable of resolving the complexity of aquifer systems. In addition to new surveys, historical AEM data sets acquired to target potential mineralization are being re-processed for groundwater related applications. As part of the South Australian Goyder FLOWS project, regional and local scale AEM data sets are being examined to develop hydrogeological conceptual models in the remote Musgrave Province in the States north. The work has required the re-processing of historical data, including those acquired by TEMPEST, HoisTEM and VTEM. More recently, the project also acquired co-incident data from several new AEM systems, including the new SkyTEM508 (a helicopter TDEM system) and the SPECTREM2000 (a fixed wing TDEM system). Their acquisition aims to inform State agencies about options for acquiring further pre-competitive AEM data to support mineral exploration whilst also addressing groundwater resource requirements for the region. In this paper we examine the results from a comparative study of these systems for defining the variability of aquifers that are expected to provide the main source of groundwater for any resource projects. We have processed and inverted data from two fixed wing TDEM systems (TEMPEST and SPECTREM2000), and two helicopter TDEM systems (VTEM and SKYTEM508) using the same model parameterization (fixed 30-layer thicknesses) and one common inversion kernel. A 1D LEI algorithm has been used and each sample has been inverted independently; the choice of the algorithm was primarily dependent on a capability to model the data. The capacity to resolve targets of a variable nature resides mainly on the ability to accurately model the system and account for the processing that may have occurred post acquisition. The comparison was undertaken for two distinct areas containing a contrasting hydrogeology. Results reveal a palaeovalley fill sequence and suggest a complex landscape evolution. Most systems resolve similar structures despite their different geometries, induction waveforms, transmitted current, and footprints. Not surprising is the ability of certain systems to detect and resolve a more complex near-surface aquifer variability. Their significance has to be considered in the context of the quality of the groundwater resource they may contain and their hydraulic properties.

Voxel inversion of airborne electromagnetic data for improved groundwater model construction and prediction accuracy

NASA Astrophysics Data System (ADS)

Kruse Christensen, Nikolaj; Ferre, Ty Paul A.; Fiandaca, Gianluca; Christensen, Steen

2017-03-01

We present a workflow for efficient construction and calibration of large-scale groundwater models that includes the integration of airborne electromagnetic (AEM) data and hydrological data. In the first step, the AEM data are inverted to form a 3-D geophysical model. In the second step, the 3-D geophysical model is translated, using a spatially dependent petrophysical relationship, to form a 3-D hydraulic conductivity distribution. The geophysical models and the hydrological data are used to estimate spatially distributed petrophysical shape factors. The shape factors primarily work as translators between resistivity and hydraulic conductivity, but they can also compensate for structural defects in the geophysical model. The method is demonstrated for a synthetic case study with sharp transitions among various types of deposits. Besides demonstrating the methodology, we demonstrate the importance of using geophysical regularization constraints that conform well to the depositional environment. This is done by inverting the AEM data using either smoothness (smooth) constraints or minimum gradient support (sharp) constraints, where the use of sharp constraints conforms best to the environment. The dependency on AEM data quality is also tested by inverting the geophysical model using data corrupted with four different levels of background noise. Subsequently, the geophysical models are used to construct competing groundwater models for which the shape factors are calibrated. The performance of each groundwater model is tested with respect to four types of prediction that are beyond the calibration base: a pumping well's recharge area and groundwater age, respectively, are predicted by applying the same stress as for the hydrologic model calibration; and head and stream discharge are predicted for a different stress situation. As expected, in this case the predictive capability of a groundwater model is better when it is based on a sharp geophysical model instead of a smoothness constraint. This is true for predictions of recharge area, head change, and stream discharge, while we find no improvement for prediction of groundwater age. Furthermore, we show that the model prediction accuracy improves with AEM data quality for predictions of recharge area, head change, and stream discharge, while there appears to be no accuracy improvement for the prediction of groundwater age.

Studies on Agri-environmental Measures: A Survey of the Literature

NASA Astrophysics Data System (ADS)

Uthes, Sandra; Matzdorf, Bettina

2013-01-01

Agri-environmental measures (AEM) are incentive-based instruments in the European Union (EU) that provide payments to farmers for voluntary environmental commitments related to preserving and enhancing the environment and maintaining the cultural landscape. We review the AEM literature and provide an overview of important research topics, major research results and future challenges as discussed in the available literature concerning these measures. This review contributes to the existing literature by attempting to equally consider ecological and economic perspectives. The reviewed articles are analyzed regarding their regional focus, topics and methods. The analytical section of the article seeks to discuss commonly asked questions about AEM on the basis of results from reviewed studies. The vast amount of available literature provides valuable insights into specific cases and reveals a complex picture with few general conclusions. The existing research is usually either biased toward ecological or economic perspectives and fails to provide a holistic picture of the problems and challenges within agri-environmental programming (e.g., multiple measures, multiple target areas, legal aspects, financial constraints, transaction costs). Most empirical studies provide detailed insights into selected individual measures but are incapable of providing results at a level relevant to decision-making, as they neglect the role of farmers and the available AEM budget. Predominantly economic approaches often only consider rough assumptions of ecological and economic processes and are also not suitable for decision-making. Decision-support tools that build on these disciplinary results and simultaneously consider scheme factors and environmental conditions at high spatial resolution for application by the responsible authorities are rare and require further research.

Generation of 3-D hydrostratigraphic zones from dense airborne electromagnetic data to assess groundwater model prediction error

USGS Publications Warehouse

Christensen, Nikolaj K; Minsley, Burke J.; Christensen, Steen

2017-01-01

We present a new methodology to combine spatially dense high-resolution airborne electromagnetic (AEM) data and sparse borehole information to construct multiple plausible geological structures using a stochastic approach. The method developed allows for quantification of the performance of groundwater models built from different geological realizations of structure. Multiple structural realizations are generated using geostatistical Monte Carlo simulations that treat sparse borehole lithological observations as hard data and dense geophysically derived structural probabilities as soft data. Each structural model is used to define 3-D hydrostratigraphical zones of a groundwater model, and the hydraulic parameter values of the zones are estimated by using nonlinear regression to fit hydrological data (hydraulic head and river discharge measurements). Use of the methodology is demonstrated for a synthetic domain having structures of categorical deposits consisting of sand, silt, or clay. It is shown that using dense AEM data with the methodology can significantly improve the estimated accuracy of the sediment distribution as compared to when borehole data are used alone. It is also shown that this use of AEM data can improve the predictive capability of a calibrated groundwater model that uses the geological structures as zones. However, such structural models will always contain errors because even with dense AEM data it is not possible to perfectly resolve the structures of a groundwater system. It is shown that when using such erroneous structures in a groundwater model, they can lead to biased parameter estimates and biased model predictions, therefore impairing the model's predictive capability.

Generation of 3-D hydrostratigraphic zones from dense airborne electromagnetic data to assess groundwater model prediction error

NASA Astrophysics Data System (ADS)

Christensen, N. K.; Minsley, B. J.; Christensen, S.

2017-02-01

We present a new methodology to combine spatially dense high-resolution airborne electromagnetic (AEM) data and sparse borehole information to construct multiple plausible geological structures using a stochastic approach. The method developed allows for quantification of the performance of groundwater models built from different geological realizations of structure. Multiple structural realizations are generated using geostatistical Monte Carlo simulations that treat sparse borehole lithological observations as hard data and dense geophysically derived structural probabilities as soft data. Each structural model is used to define 3-D hydrostratigraphical zones of a groundwater model, and the hydraulic parameter values of the zones are estimated by using nonlinear regression to fit hydrological data (hydraulic head and river discharge measurements). Use of the methodology is demonstrated for a synthetic domain having structures of categorical deposits consisting of sand, silt, or clay. It is shown that using dense AEM data with the methodology can significantly improve the estimated accuracy of the sediment distribution as compared to when borehole data are used alone. It is also shown that this use of AEM data can improve the predictive capability of a calibrated groundwater model that uses the geological structures as zones. However, such structural models will always contain errors because even with dense AEM data it is not possible to perfectly resolve the structures of a groundwater system. It is shown that when using such erroneous structures in a groundwater model, they can lead to biased parameter estimates and biased model predictions, therefore impairing the model's predictive capability.

Skeletal muscle adaptations to microgravity exposure in the mouse.

PubMed

Harrison, B C; Allen, D L; Girten, B; Stodieck, L S; Kostenuik, P J; Bateman, T A; Morony, S; Lacey, D; Leinwand, L A

2003-12-01

To investigate the effects of microgravity on murine skeletal muscle fiber size, muscle contractile protein, and enzymatic activity, female C57BL/6J mice, aged 64 days, were divided into animal enclosure module (AEM) ground control and spaceflight (SF) treatment groups. SF animals were flown on the space shuttle Endeavour (STS-108/UF-1) and subjected to approximately 11 days and 19 h of microgravity. Immunohistochemical analysis of muscle fiber cross-sectional area revealed that, in each of the muscles analyzed, mean muscle fiber cross-sectional area was significantly reduced (P < 0.0001) for all fiber types for SF vs. AEM control. In the soleus, immunohistochemical analysis of myosin heavy chain (MHC) isoform expression revealed a significant increase in the percentage of muscle fibers expressing MHC IIx and MHC IIb (P < 0.05). For the gastrocnemius and plantaris, no significant changes in MHC isoform expression were observed. For the muscles analyzed, no alterations in MHC I or MHC IIa protein expression were observed. Enzymatic analysis of the gastrocnemius revealed a significant decrease in citrate synthase activity in SF vs. AEM control.

Analysis of cocaine and three of its metabolites in hair by gas chromatography-mass spectrometry using ion-trap detection for CI/MS/MS.

PubMed

Cognard, Emmanuelle; Rudaz, Serge; Bouchonnet, Stéphane; Staub, Christian

2005-11-05

A sensitive GC/CI/MS/MS method was developed for the simultaneous determination of cocaine (COC), anhydroecgonine methylester (cocaine pyrolysis product, AEME), ecgonine methylester (cocaine enzymatic hydrolysis product, EME) and cocaethylene (cocaine with ethanol trans-esterification product, COET) in human hair samples. After acid hydrolysis, hair samples were extracted with an automated solid phase extraction (SPE). The analysis of cocaine and its three metabolites was performed using an ion-trap spectrometer in positive chemical ionization with isobutane as gas reagent. The procedure was validated. Weighted linear regression was found appropriate in a concentration range of 0.10-5.00 ng/mg for AEME, 0.05-5.00 ng/mg for COC, EME and COET. The limit of detection was estimated at 0.005 ng/mg for COC and COET, at 0.025 ng/mg for EME, and at 0.050 ng/mg for AEME. Method performance was evaluated in terms of trueness and precision using quality control (QC) samples over the investigated ranges. Method selectivity and robustness were also demonstrated.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buck, E.C.; Cunnane, J.C.; Brown, N.R.

A combination of optical microscopy, scanning electron microscopy with backscattered electron detection (SEM/BSE), and analytical electron microscopy (AEM) is being used to determine the nature of uranium in soils from the Fernald Environmental Management Project. The information gained from these studies is being used to develop and test remediation technologies. Investigations using SEM have shown that uranium is contained within particles that are typically 1 to 100 {mu}m in diameter. Further analysis with AEM has shown that these uranium-rich regions are made up of discrete uranium-bearing phases. The distribution of these uranium phases was found to be inhomogeneous at themore » microscopic level.« less

Nanoscale Characterization of Elemental Partitioning Between Gamma and Gamma Prime Phases in Rene 88DT Nickel Base Superalloy (Preprint)

DTIC Science & Technology

2008-02-01

penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN...analysis "as condu,ted on a FEI Tecnai F20 field emission gun transmission electron microscope operaling at 200 KV. Imagcs were obtained using lhe Cr M...line marked AI3 in (a). The neck region exhibil’ an inlensity lying in t>etween lhal of lhe yand y’phases. (c) Inlensily prot1le aemS > lhe line CD in (a

A promising tool for subsurface permafrost mapping-An application of airborne geophysics from the Yukon River Basin, Alaska

USGS Publications Warehouse

Abraham, Jared E.

2011-01-01

In the area of Fort Yukon, the AEM survey shows elevated resistivities extending to depth, likely indicative of thick permafrost. This depth corresponds well to observations from a borehole drilled in the area in the late 1990s, which detected permafrost to a depth of about 100 meters (Clark and others, 2009). In contrast to the area of Fort Yukon, the Yukon River and its floodplain are not associated with deep resistive sediments, suggesting a lack of deep permafrost, at least within the depth range of the AEM mapping (fig. 3).

Advanced analytical electron microscopy for alkali-ion batteries

DOE PAGES

Qian, Danna; Ma, Cheng; Meng, Ying Shirley; ...

2015-06-26

Lithium-ion batteries are a leading candidate for electric vehicle and smart grid applications. However, further optimizations of the energy/power density, coulombic efficiency and cycle life are still needed, and this requires a thorough understanding of the dynamic evolution of each component and their synergistic behaviors during battery operation. With the capability of resolving the structure and chemistry at an atomic resolution, advanced analytical transmission electron microscopy (AEM) is an ideal technique for this task. The present review paper focuses on recent contributions of this important technique to the fundamental understanding of the electrochemical processes of battery materials. A detailed reviewmore » of both static (ex situ) and real-time (in situ) studies will be given, and issues that still need to be addressed will be discussed.« less

Development of radon-222 as a natural tracer for monitoring the remediation of NAPL contamination in the subsurface. 1998 annual progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Semprini, L.; Istok, J.

'The objective of this research is to develop a unique method of using naturally occurring radon-222 as a tracer for locating and quantitatively describing the presence of subsurface NAPL contamination. The research will evaluate using radon as an inexpensive, yet highly accurate, means of detecting NAPL contamination and assessing the effectiveness of NAPL remediation. Laboratory, field, and modeling studies are being performed to evaluate this technique, and to develop methods for its successful implementation in practice. This report summarizes work that has been accomplished after 1-year of a 3-year project. The research to date has included radon tracer tests inmore » physical aquifer models (PAMs) and field studies at Site 300 of the Lawrence Livermore National Laboratory, CA, and Site 100D at Hanford DOE Facility, WA. The PAM tests have evaluated the ability of radon as a tracer to monitor the remediation of TCE NAPL contamination using surfactant treatment, and oxidation with permanganate. The surfactant tests were performed in collaboration with Dr. Jack Istok and Dr. Jennifer Field and their EMSP project ``In-situ, Field-Scale Evaluation of Surfactant Enhanced DNAPL Recovery Using a Single-Well-Push-Pull Test.'''' This collaboration enabled the EMSP radon project to make rapid progress. The PAM surfactant tests were performed in a radial flow geometry to simulate the push-pull-method that is being developed for surfactant field tests. The radon tests were easily incorporated into these experiments, since they simply rely on measuring the natural radon present in the subsurface fluids. Two types of radon tests were performed: (1) static tests where radon was permitted to build-up to steady-state concentrations in the pore fluids and the groundwater concentrations were monitored, and (2) dynamic tests were the radon response during push-pull surfactant tests was measured. Both methods were found to be useful in determining how NAPL remediation was progressing.'« less

A Program Aimed toward Inclusive Excellence for Underrepresented Undergraduate Women in the Sciences.

PubMed

Katz, Laura A; Aloisio, Kathryn M; Horton, Nicholas J; Ly, Minh; Pruss, Sara; Queeney, Kate; Rowen, Cate; DiBartolo, Patricia Marten

2017-01-01

Created to foster inclusive excellence, Smith College's Achieving Excellence in Mathematics, Engineering, and Science (AEMES) Scholars program provides early faculty-mentored research opportunities and other programming as a way to foster success in academic outcomes for underrepresented women in science. Using academic record data, we compared Scholars' outcomes over time with those of underrepresented students before program launch and to relevant peer comparison groups. Since its launch, AEMES Scholars have achieved significantly higher gateway life sciences course grade point averages (GPAs), rates of persistence in life and natural sciences, and participation in natural sciences advanced research relative to baseline. Gains for Scholars in gateway course GPA eliminated the significant gap that previously existed between science, technology, engineering, and mathematics (STEM)-underrepresented and other students, whereas gains in natural sciences persistence now has Scholars continuing in STEM at significantly higher rates than all other students. Many of the gains for AEMES Scholars were echoed in findings of improved outcomes for our STEM students overall since AEMES' launch. Underrepresented students who were not part of the Scholars program also evidenced increased gateway course GPA over this same period. We discuss potential explanations for these outcomes and ongoing work aimed at achieving further inclusive excellence for women in the sciences. © 2017 L. A. Katz et al. CBE—Life Sciences Education © 2017 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

The spectrum of central nervous system infections in an adult referral hospital in Hanoi, Vietnam.

PubMed

Taylor, Walter R; Nguyen, Kinh; Nguyen, Duc; Nguyen, Huyen; Horby, Peter; Nguyen, Ha L; Lien, Trinh; Tran, Giang; Tran, Ninh; Nguyen, Ha M; Nguyen, Thai; Nguyen, Ha H; Nguyen, Thanh; Tran, Giap; Farrar, Jeremy; de Jong, Menno; Schultsz, Constance; Tran, Huong; Nguyen, Diep; Vu, Bich; Le, Hoa; Dao, Trinh; Nguyen, Trung; Wertheim, Heiman

2012-01-01

To determine prospectively the causative pathogens of central nervous system (CNS) infections in patients admitted to a tertiary referral hospital in Hanoi, Vietnam. From May 2007 to December 2008, cerebrospinal fluid (CSF) samples from 352 adults with suspected meningitis or encephalitis underwent routine testing, staining (Gram, Ziehl-Nielsen, India ink), bacterial culture and polymerase chain reaction targeting Neisseria meningitidis, Streptococcus pneumoniae, S. suis, Haemophilus influenzae type b, Herpes simplex virus (HSV), Varicella Zoster virus (VZV), enterovirus, and 16S ribosomal RNA. Blood cultures and clinically indicated radiology were also performed. Patients were classified as having confirmed or suspected bacterial (BM), tuberculous (TBM), cryptococcal (CRM), eosinophilic (EOM) meningitis, aseptic encephalitis/meningitis (AEM), neurocysticercosis and others. 352 (male: 66%) patients were recruited: median age 34 years (range 13-85). 95/352 (27.3%) diagnoses were laboratory confirmed and one by cranial radiology: BM (n = 62), TBM (n = 9), AEM (n = 19), CRM (n = 5), and neurocysticercosis (n = 1, cranial radiology). S. suis predominated as the cause of BM [48/62 (77.4%)]; Listeria monocytogenese (n = 1), S. pasteurianus (n = 1) and N. meningitidis (n = 2) were infrequent. AEM viruses were: HSV (n = 12), VZV (n = 5) and enterovirus (n = 2). 5 patients had EOM. Of 262/352 (74.4%) patients with full clinical data, 209 (79.8%) were hospital referrals and 186 (71%) had been on antimicrobials. 21 (8%) patients died: TBM (15.2%), AEM (10%), and BM (2.8%). Most infections lacked microbiological confirmation. S. suis was the most common cause of BM in this setting. Improved diagnostics are needed for meningoencephalitic syndromes to inform treatment and prevention strategies.

The Spectrum of Central Nervous System Infections in an Adult Referral Hospital in Hanoi, Vietnam

PubMed Central

Taylor, Walter R.; Nguyen, Kinh; Nguyen, Duc; Nguyen, Huyen; Horby, Peter; Nguyen, Ha L.; Lien, Trinh; Tran, Giang; Tran, Ninh; Nguyen, Ha M.; Nguyen, Thai; Nguyen, Ha H.; Nguyen, Thanh; Tran, Giap; Farrar, Jeremy; de Jong, Menno; Schultsz, Constance; Tran, Huong; Nguyen, Diep; Vu, Bich; Le, Hoa; Dao, Trinh; Nguyen, Trung; Wertheim, Heiman

2012-01-01

Objectives To determine prospectively the causative pathogens of central nervous system (CNS) infections in patients admitted to a tertiary referral hospital in Hanoi, Vietnam. Methods From May 2007 to December 2008, cerebrospinal fluid (CSF) samples from 352 adults with suspected meningitis or encephalitis underwent routine testing, staining (Gram, Ziehl-Nielsen, India ink), bacterial culture and polymerase chain reaction targeting Neisseria meningitidis, Streptococcus pneumoniae, S. suis, Haemophilus influenzae type b, Herpes simplex virus (HSV), Varicella Zoster virus (VZV), enterovirus, and 16S ribosomal RNA. Blood cultures and clinically indicated radiology were also performed. Patients were classified as having confirmed or suspected bacterial (BM), tuberculous (TBM), cryptococcal (CRM), eosinophilic (EOM) meningitis, aseptic encephalitis/meningitis (AEM), neurocysticercosis and others. Results 352 (male: 66%) patients were recruited: median age 34 years (range 13–85). 95/352 (27.3%) diagnoses were laboratory confirmed and one by cranial radiology: BM (n = 62), TBM (n = 9), AEM (n = 19), CRM (n = 5), and neurocysticercosis (n = 1, cranial radiology). S. suis predominated as the cause of BM [48/62 (77.4%)]; Listeria monocytogenese (n = 1), S. pasteurianus (n = 1) and N. meningitidis (n = 2) were infrequent. AEM viruses were: HSV (n = 12), VZV (n = 5) and enterovirus (n = 2). 5 patients had EOM. Of 262/352 (74.4%) patients with full clinical data, 209 (79.8%) were hospital referrals and 186 (71%) had been on antimicrobials. 21 (8%) patients died: TBM (15.2%), AEM (10%), and BM (2.8%). Conclusions Most infections lacked microbiological confirmation. S. suis was the most common cause of BM in this setting. Improved diagnostics are needed for meningoencephalitic syndromes to inform treatment and prevention strategies. PMID:22952590

Energy Balance Bowen Ratio (EBBR) Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, D. R.

2016-01-01

The Energy Balance Bowen Ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors frommore » instrument offset drift.« less

Energy Balance Bowen Ratio Station (EBBR) Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, DR

2011-02-23

The energy balance Bowen ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors frommore » instrument offset drift.« less

Solid-Body Fuse Developed for High- Voltage Space Power Missions

NASA Technical Reports Server (NTRS)

Dolce, James L.; Baez, Anastacio N.

2001-01-01

AEM Incorporated has completed the development, under a NASA Glenn Research Center contract, of a solid-body fuse for high-voltage power systems of satellites and spacecraft systems. High-reliability fuses presently defined by MIL-PRF-23419 do not meet the increased voltage and amperage requirements for the next generation of spacecraft. Solid-body fuses exhibit electrical and mechanical attributes that enable these fuses to perform reliably in the vacuum and high-vibration and -shock environments typically present in spacecraft applications. The construction and screening techniques for solid-body fuses described by MIL-PRF-23419/12 offer an excellent roadmap for the development of high-voltage solid-body fuses.

Magnetometer bias determination and attitude determination for near-earth spacecraft

NASA Technical Reports Server (NTRS)

Lerner, G. M.; Shuster, M. D.

1979-01-01

A simple linear-regression algorithm is used to determine simultaneously magnetometer biases, misalignments, and scale factor corrections, as well as the dependence of the measured magnetic field on magnetic control systems. This algorithm has been applied to data from the Seasat-1 and the Atmosphere Explorer Mission-1/Heat Capacity Mapping Mission (AEM-1/HCMM) spacecraft. Results show that complete inflight calibration as described here can improve significantly the accuracy of attitude solutions obtained from magnetometer measurements. This report discusses the difficulties involved in obtaining attitude information from three-axis magnetometers, briefly derives the calibration algorithm, and presents numerical results for the Seasat-1 and AEM-1/HCMM spacecraft.

Simultaneous specimen and stage cleaning device for analytical electron microscope

DOEpatents

Zaluzec, Nestor J.

1996-01-01

An improved method and apparatus are provided for cleaning both a specimen stage, a specimen and an interior of an analytical electron microscope (AEM). The apparatus for cleaning a specimen stage and specimen comprising a plasma chamber for containing a gas plasma and an air lock coupled to the plasma chamber for permitting passage of the specimen stage and specimen into the plasma chamber and maintaining an airtight chamber. The specimen stage and specimen are subjected to a reactive plasma gas that is either DC or RF excited. The apparatus can be mounted on the analytical electron microscope (AEM) for cleaning the interior of the microscope.

On NMR prediction of the effectiveness of p-phenylenediamine antioxidants

NASA Astrophysics Data System (ADS)

Puškárová, Ingrid; Šoral, Michal; Breza, Martin

2015-10-01

NMR shifts of N-phenyl-N‧-alkyl-p-phenylenediamines (PPD) in DMSO have been measured as well as evaluated by B3LYP calculations. According to Simon et al. Molar Antioxidant Effectiveness (AEM) of PPD antioxidants depends on the bond strength of hydrogens to amine nitrogens between aromatic rings (NA), to the side aliphatic chain nitrogens (NB) and to its neighboring tertiary carbon atoms (CT). AEM increases with NMR shifts of HA, HB, NA and probably also of CT atoms whereas NMR shifts of NB atoms exhibit a reverse trend. This is very surprising because similar reactions at A and B sites are supposed.

COLLOID-FACILITATED TRANSPORT OF RADIONUCLIDES THROUGH THE VADOSE ZONE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flury, Markus

2003-09-14

Contaminants have leaked into the vadose zone at the USDOE Hanford reservation. It is important to understand the fate and transport of these contaminants to design remediation strategies and long-term waste management plans at the Hanford reservation. Colloids may play an important role in fate and transport of strongly sorbing contaminants, such as Cs or Pu. This project seeks to improve the basic understanding of colloid and colloid-facilitated transport of contaminants in the vadose zone. The specific objectives addressed are: (1) Determine the structure, composition, and surface charge characteristics of colloidal particles formed under conditions similar to those occurring duringmore » leakage of waste typical of Hanford tank supernatants into soils and sediments surrounding the tanks. (2) Characterize the mutual interactions between colloids, contaminant, and soil matrix in batch experiments under various ionic strength and pH conditions. We will investigate the nature of the solid-liquid interactions and the kinetics of the reactions. (3) Evaluate mobility of colloids through soil under different degrees of water saturation and solution chemistry (ionic strength and pH). (4) Determine the potential of colloids to act as carriers to transport the contaminant through the vadose zone and verify the results through comparison with field samples collected under leaking tanks. (5) Improve conceptual characterization of colloid-contaminant-soil interactions and colloid-facilitated transport for implementation into reactive chemical transport models. This project was in part supported by an NSF-IGERT grant to Washington State University. The IGERT grant provided funding for graduate student research and education, and two graduate students were involved in the EMSP project. The IGERT program also supported undergraduate internships. The project is part of a larger EMSP program to study fate and transport of contaminants under leaking Hanford waste tanks. The project has close relations to the following EMSP projects: Project: 70126, Interfacial Soil Chemistry of Radionuclides in the Unsaturated Zone (PI: Jon Chorover) Project: 70070, Reactivity of Primary Soil Minerals and Secondary Precipitates (PI: Kathy Nagy) Cesium Transport in Hanford Sediments: Application of an Experimentally Based Cation Exchange Model (PI: Susan Carroll and Carl Steefel).« less

HCMM satellite to take earth's temperature

NASA Technical Reports Server (NTRS)

1978-01-01

The heat capacity mapping mission (HCMM), a low cost modular spacecraft built for the Applications Explorer Missions (AEM), was designed to allow scientists to determine the feasibility of using day/night thermal infrared remote sensor-derived data to: (1) discriminate various rock types and locate mineral resources; (2) measure and monitor surface soil moisture changes; (3) measure plant canopy temperatures at frequent intervals to determine transpiration of water and plant stress; and (4) measure urban heat islands. The design of the spacecraft (AEM-A), its payload, launch vehicle, orbit, and data collection and processing methods are described. Projects in which the HCMM data will be applied by 12 American and 12 foreign investigators are summarized.

The Wavelength-Dispersive Spectrometer and Its Proposed Use in the Analytical Electron Microscope

NASA Technical Reports Server (NTRS)

Goldstein, Joseph I.; Lyman, Charles E.; Williams, David B.

1989-01-01

The Analytical Electron Microscope (AEM) equipped with a wavelength-dispersive spectrometer (WDS) should have the ability to resolve peaks which normally overlap in the spectra from an energy-dispersive spectrometer (EDS). With a WDS it should also be possible to measure lower concentrations of elements in thin foils due to the increased peak-to-background ratio compared with EDS. The WDS will measure X-ray from the light elements (4 less than Z less than 1O) more effectively. This paper addresses the possibility of interfacing a compact WDS with a focussing circle of approximately 4 cm to a modem AEM with a high-brightness (field emission) source of electrons.

Highly durable direct hydrazine hydrate anion exchange membrane fuel cell

NASA Astrophysics Data System (ADS)

Sakamoto, Tomokazu; Serov, Alexey; Masuda, Teruyuki; Kamakura, Masaki; Yoshimoto, Koji; Omata, Takuya; Kishi, Hirofumi; Yamaguchi, Susumu; Hori, Akihiro; Horiuchi, Yousuke; Terada, Tomoaki; Artyushkova, Kateryna; Atanassov, Plamen; Tanaka, Hirohisa

2018-01-01

The factors influenced on degradation of direct hydrazine hydrate fuel cells (DHFCs) under operation conditions are analyzed by in situ soft X-ray radiography. A durability of DHFCs is significantly improved by multi-step reaction DHFCs (MSR-DHFCs) approach designed to decrease the crossover of liquid fuel. An open circuit voltage (OCV) as well as cell voltage at 5 mA cm-2 of MSR-DHFC construct with commercial anion exchange membrane (AEM) maintained for over of 3500 h at 60 °C. Furthermore, the commercial proton exchange membrane (PEM) is integrated into AEM of MSR-DHFCs resulting in stable power output of MSR-DHFCs for over than 2800 h at 80 °C.

Imidazolium-based Block Copolymers as Solid-State Separators for Alkaline Fuel Cells and Lithium Ion Batteries

NASA Astrophysics Data System (ADS)

Nykaza, Jacob Richard

In this study, polymerized ionic liquid (PIL) diblock copolymers were explored as solid-state polymer separators as an anion exchange membrane (AEM) for alkaline fuel cells AFCs and as a solid polymer electrolyte (SPE) for lithium-ion batteries. Polymerized ionic liquid (PIL) block copolymers are a distinct set of block copolymers that combine the properties of both ionic liquids (e.g., high conductivity, high electrochemical stability) and block copolymers (e.g., self-assembly into various nanostructures), which provides the opportunity to design highly conductive robust solid-state electrolytes that can be tuned for various applications including AFCs and lithium-ion batteries via simple anion exchange. A series of bromide conducting PIL diblock copolymers with an undecyl alkyl side chain between the polymer backbone and the imidazolium moiety were first synthesized at various compositions comprising of a PIL component and a non-ionic component. Synthesis was achieved by post-functionalization from its non-ionic precursor PIL diblock copolymer, which was synthesized via the reverse addition fragmentation chain transfer (RAFT) technique. This PIL diblock copolymer with long alkyl side chains resulted in flexible, transparent films with high mechanical strength and high bromide ion conductivity. The conductivity of the PIL diblock copolymer was three times higher than its analogous PIL homopolymer and an order of magnitude higher than a similar PIL diblock copolymer with shorter alkyl side chain length, which was due to the microphase separated morphology, more specifically, water/ion clusters within the PIL microdomains in the hydrated state. Due to the high conductivity and mechanical robustness of this novel PIL block copolymer, its application as both the ionomer and AEM in an AFC was investigated via anion exchange to hydroxide (OH-), where a maximum power density of 29.3 mW cm-1 (60 °C with H2/O2 at 25 psig (172 kPa) backpressure) was achieved. Rotating disk electrode (RDE) experiments determined the interfacial resistance imposed during cell assembly between the AEM, catalyst, and ionomer was a factor in fuel cell performance. Further RDE studies investigated the electrochemical stability of the PIL block copolymer ionomer under applied potentials, where it was determined that potential cycling increased the degradation compared to constant voltage or open circuit voltage studies. The PIL diblock copolymer was then anion exchanged to the bis(trifluoromethane)sulfonamide (TFSI-) anion form and imbibed with a lithium salt and ionic liquid solution for use as a SPE in lithium-ion batteries resulting in a maximum discharge capacity of 112 mAh g-1 at 0.1 C with a Coulombic efficiency greater than 94% over 100 cycles. PIL block copolymers have promising mechanical properties and transport properties (i.e., ion conductivity) in both the hydrated (hydrophilic anions; Br-, OH-) and dry (hydrophobic anions; TFSI-) states resulting in highly conductive, chemically/thermally stable, and mechanically robust solid-state polymer separators for use as AEMs in AFCs and as SPEs in lithium-ion batteries.

Ion exchange membrane textile bioreactor as a new alternative for drinking water denitrification.

PubMed

Berdous, Dalila; Akretche, Djamal-Eddine; Abderahmani, Ahmed; Berdous, Sakina; Meknaci, Rima

2014-06-01

This work enters in the optics of the denitrification of a polluted water by two membrane techniques, the Donnan dialysis (DD) and the ion exchange membrane bioreactor (IEMB), using a conventional barrier, composed by an anion exchange membrane (AEM), and a hybrid barrier, where the AEM is combined to an anion exchange textile (AET). The effects of the hydrodynamic factor and the nature of the carbon source on the transfer and the reduction of nitrate ions were studied. The study results obtained through the DD showed the effectiveness of the hybrid barrier in the recovery and concentration of nitrate ions. This was also recorded during denitrification by the hybrid process, called the ion exchange membrane textile bioreactor (IEMTB), with a significant reduction of nitrates, compared to IEMB, due to the efficiency of the Pseudomonas aeruginosa biofilm formed at the surface of the AET. Here, the permselectivity of the membrane and the good bioreduction of the pollutants are no longer major conditions to the better performance of the process. The application of IEMTB in the denitrification of groundwater, having a nitrate concentration of 96.67 ppm, shows a total reduction of nitrate ions without changing the quality of the water. Indeed, the analysis of the recovered water, or yet the treated water, shows the absence of the bacterium by-products and concentrations in the nitrates and nitrites which are, respectively, equal to 0.02±0.01 ppm, and inferiors to the detection limit (<0.02 ppm).

Chemically durable polymer electrolytes for solid-state alkaline water electrolysis

NASA Astrophysics Data System (ADS)

Park, Eun Joo; Capuano, Christopher B.; Ayers, Katherine E.; Bae, Chulsung

2018-01-01

Generation of high purity hydrogen using electrochemical splitting of water is one of the most promising methods for sustainable fuel production. The materials to be used as solid-state electrolytes for alkaline water electrolyzer require high thermochemical stability against hydroxide ion attack in alkaline environment during the operation of electrolysis. In this study, two quaternary ammonium-tethered aromatic polymers were synthesized and investigated for anion exchange membrane (AEM)-based alkaline water electrolyzer. The membranes properties including ion exchange capacity (IEC), water uptake, swelling degree, and anion conductivity were studied. The membranes composed of all C-C bond polymer backbones and flexible side chain terminated by cation head groups exhibited remarkably good chemical stability by maintaining structural integrity in 1 M NaOH solution at 95 °C for 60 days. Initial electrochemical performance and steady-state operation performance were evaluated, and both membranes showed a good stabilization of the cell voltage during the steady-state operation at the constant current density at 200 mA/cm2. Although both membranes in current form require improvement in mechanical stability to afford better durability in electrolysis operation, the next generation AEMs based on this report could lead to potentially viable AEM candidates which can provide high electrolysis performance under alkaline operating condition.

A Program Aimed toward Inclusive Excellence for Underrepresented Undergraduate Women in the Sciences

PubMed Central

Katz, Laura A.; Aloisio, Kathryn M.; Horton, Nicholas J.; Ly, Minh; Pruss, Sara; Queeney, Kate; Rowen, Cate; DiBartolo, Patricia Marten

2017-01-01

Created to foster inclusive excellence, Smith College’s Achieving Excellence in Mathematics, Engineering, and Science (AEMES) Scholars program provides early faculty-mentored research opportunities and other programming as a way to foster success in academic outcomes for underrepresented women in science. Using academic record data, we compared Scholars’ outcomes over time with those of underrepresented students before program launch and to relevant peer comparison groups. Since its launch, AEMES Scholars have achieved significantly higher gateway life sciences course grade point averages (GPAs), rates of persistence in life and natural sciences, and participation in natural sciences advanced research relative to baseline. Gains for Scholars in gateway course GPA eliminated the significant gap that previously existed between science, technology, engineering, and mathematics (STEM)-underrepresented and other students, whereas gains in natural sciences persistence now has Scholars continuing in STEM at significantly higher rates than all other students. Many of the gains for AEMES Scholars were echoed in findings of improved outcomes for our STEM students overall since AEMES’ launch. Underrepresented students who were not part of the Scholars program also evidenced increased gateway course GPA over this same period. We discuss potential explanations for these outcomes and ongoing work aimed at achieving further inclusive excellence for women in the sciences. PMID:28213581

Densely quaternized poly(arylene ether)s with distinct phase separation for highly anion-conductive membranes

NASA Astrophysics Data System (ADS)

Hu, Yuanfang; Wang, Bingxi; Li, Xiao; Chen, Dongyang; Zhang, Weiying

2018-05-01

To develop high performance anion exchange membranes (AEMs), a novel bisphenol monomer bearing eight benzylmethyl groups at the outer edge of the molecule was synthesized, which after condensation polymerization with various amounts of 4,4‧-dihydroxydiphenylsulfone and 4,4‧-difluorobenzophenone yielded novel poly(arylene ether)s with densely located benzylmethyl groups. These benzylmethyl groups were then converted to quaternary ammonium groups by radical-initiated bromination and quaternization in tandem, leading to the emergence of densely quaternized poly(arylene ether sulfone)s (QA-PAEs) with controlled ion exchange capacities (IECs) ranging from 1.61 to 2.32 mmol g-1. Both small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) studies revealed distinct phase separation in the QA-PAEs. The QA-PAE-40 with an IEC of 2.32 mmol g-1 exhibited a Br- conductivity of 9.2 mS cm-1 and a SO42- conductivity of 14.0 mS cm-1 at room temperature, much higher than those of a control membrane with a similar IEC but without obvious phase separation. Therefore, phase separation of AEMs was validated to be advantageous for the efficient conducting of anions. The experimental results also showed that the QA-PAEs were promising AEM materials, especially for non-alkaline applications.

PdRu/C catalysts for ethanol oxidation in anion-exchange membrane direct ethanol fuel cells

NASA Astrophysics Data System (ADS)

Ma, Liang; He, Hui; Hsu, Andrew; Chen, Rongrong

2013-11-01

Carbon supported PdRu catalysts with various Pd:Ru atomic ratios were synthesized by impregnation method, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electrochemical half-cell tests, and the anion-exchange membrane direct ethanol fuel cell (AEM-DEFC) tests. XRD results suggest that the PdRu metal exists on carbon support in an alloy form. TEM study shows that the bimetallic PdRu/C catalysts have slightly smaller average particle size than the single metal Pd/C catalyst. Lower onset potential and peak potential and much higher steady state current for ethanol oxidation in alkaline media were observed on the bimetallic catalysts (PdxRuy/C) than on the Pd/C, while the activity for ethanol oxidation on the pure Ru/C was not noticeable. By using Pd/C anode catalysts and MnO2 cathode catalysts, AEM-DEFCs free from the expensive Pt catalyst were assembled. The AEM DEFC using the bimetallic Pd3Ru/C anode catalyst showed a peak power density as high as 176 mW cm-2 at 80 °C, about 1.8 times higher than that using the single metal Pd/C catalyst. The role of Ru for enhancing the EOR activity of Pd/C catalysts is discussed.

Thermochemical Stability Study of Alkyl-Tethered Quaternary Ammonium Cations for Anion Exchange Membrane Fuel Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohanty, Angela D.; Tignor, Steven E.; Sturgeon, Matthew R.

2017-01-01

The increased interest in the use of anion exchange membranes (AEMs) for applications in electrochemical devices has prompted significant efforts in designing materials with robust stability in alkaline media. Most reported AEMs suffer from polymer backbone degradation as well as cation functional group degradation. In this report, we provide comprehensive experimental investigations for the analysis of cation functional group stability under alkaline media. A silver oxide-mediated ion exchange method and an accelerated stability test in aqueous KOH solutions at elevated temperatures using a Parr reactor were used to evaluate a broad scope of quaternary ammonium (QA) cationic model compound structures,more » particularly focusing on alkyl-tethered cations. Additionally, byproduct analysis was employed to gain better understanding of degradation pathways and trends of alkaline stability. Experimental results under different conditions gave consistent trends in the order of cation stability of various QA small molecule model compounds. Overall, cations that are benzyl-substituted or that are near to electronegative atoms (such as oxygen) degrade faster in alkaline media in comparison to alkyl-tethered QAs. These comprehensive model compound stability studies provide valuable information regarding the relative stability of various cation structures and can help guide researchers towards designing new and promising candidates for AEM materials.« less

AEM of extraterrestrial materials

NASA Technical Reports Server (NTRS)

Mackinnon, I. D. R.

1982-01-01

Modifications to and maintenance of the JEOL 100 CX electron microscope are discussed. Research activity involving extraterrestrial matter, cosmic dust, stratosphere dust, and meteorites is summarized.

Effort for money? Farmers' rationale for participation in agri-environment measures with different implementation complexity.

PubMed

Van Herzele, Ann; Gobin, Anne; Van Gossum, Peter; Acosta, Lilibeth; Waas, Tom; Dendoncker, Nicolas; Henry de Frahan, Bruno

2013-12-15

European agri-environment programmes are based on the common principle that farmers deliver environmental services for which society pays. Due to the voluntary nature of agri-environment measures (AEM), the issue of farmers' motives or reasons for participation has been an important topic of investigation in past years. The present paper examines farmers' rationale for participation in AEM against the backdrop of continued debate over whether to develop relatively simple measures that can be readily applied by many farmers or give greater priority to measures that are more targeted - i.e. to the specific management requirement of particular habitats or species - but are often more complex. The paper draws on empirical material from a case study in the Dyle valley, Belgium, including in-depth interviews, expert consultations and a mail survey. It was sought not only to identify and quantify the importance of separate reasons for participation, but also to reveal how these reasons and other elements of relevance were logically interrelated in the explanation that farmers themselves give for their participation. As a result, six modes or styles of participation were identified: opportunistic, calculative, compensatory, optimising, catalysing and engaged. The analyses suggest that there were notable differences in that both separate reasons for and modes of participation do vary with the complexity of the measures' requirements. Overall, the study demonstrates that participation in AEM is not simply a matter of weighing the money against the effort for adoption. Whereas money is an important driver for participation (in particular, for those adopting complex AEM) it plays widely differing roles depending on the level of farmers' reasoning (farm enterprise, single practice or landscape feature) and the importance they give to other considerations (environmental effect, production potential of land, goodness of fit, etc.). Practical implications are drawn for both policy makers and programme managers who develop and make available tailor-made support. Copyright © 2013 Elsevier Ltd. All rights reserved.

The patient's perspective: How to create awareness for improving access to care and treatment of MS patients?

PubMed

Vermersch, Patrick; Faller, Andreas; Czarnota-Szałkowska, Dominika; Meesen, Bianca; Thalheim, Christoph

2016-08-01

There is currently no known cure for multiple sclerosis (MS). Four stakeholders play a major role in MS: healthcare professionals, regulators, payers and patients. In Europe, patients are represented by the European Multiple Sclerosis Platform (EMSP), which aims to improve MS management and patients' quality of life. The EMSP has recently shown that there are major disparities in Europe in terms of access to care and treatment. Implementing the Code of Good Practice and a standardised MS nurse training may be useful in harmonising MS management across Europe. Additionally, the burden for novel therapeutic options to be approved by regulatory agencies has to decrease in order to provide faster access of treatment to patients. Data collection (e.g. national registers) also appears crucial to help research and shape the most effective policy in each country. Finally, people with MS should get appropriate (financial) support in order to complete their studies and find a job, as their active participation in society requires proper access to education and employment. Moreover, as they are the ones affected by MS, they seem to be best placed to represent themselves and their needs and should be consulted more often during decision-making processes by policy makers, regulators and payers. © The Author(s), 2016.

Voluntary emotion regulation in anorexia nervosa: A preliminary emotion-modulated startle investigation.

PubMed

Racine, Sarah E; Forbush, Kelsie T; Wildes, Jennifer E; Hagan, Kelsey E; Pollack, Lauren O; May, Casey

2016-06-01

Emotion regulation difficulties are implicated in the development and maintenance of anorexia nervosa (AN). However, research has been limited by an almost exclusive reliance on self-report. This study is the first to use the emotion-modulated startle paradigm (EMSP) to investigate emotional reactivity and voluntary emotion regulation in individuals with AN. Twenty women with AN viewed negative, positive, neutral, and food images and were asked to enhance, suppress, or maintain their emotional responses mid-way through picture presentation. Startle eyeblink magnitudes in response to startle probes administered prior, and subsequent, to regulation instructions indexed emotional reactivity and regulation, respectively. On emotional reactivity trials, startle magnitudes were greater for negative, positive, and food images, compared to neutral images. Participants had difficulty suppressing startle responses to negative and food images, as indicated by non-significant suppress-maintain comparisons. In contrast, startle responses to enhance and suppress cues during presentation of pleasant images were comparable and significantly lower than maintain cues. Findings converge with self-report data to suggest that patients with AN have difficulties with voluntary emotion regulation. The EMSP may be a promising trans-diagnostic method for examining emotion regulation difficulties that underlie risk for eating disorders and other psychiatric conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Poly(terphenylene) Anion Exchange Membranes: The Effect of Backbone Structure on Morphology and Membrane Property

DOE PAGES

Lee, Woo-Hyung; Park, Eun Joo; Han, Junyoung; ...

2017-05-05

A new design concept for ion-conducting polymers in anion exchange membranes (AEMs) fuel cells is proposed based on structural studies and conformational analysis of polymers and their effect on the properties of AEMs. Thermally, chemically, and mechanically stable terphenyl-based polymers with pendant quaternary ammonium alkyl groups were synthesized to investigate the effect of varying the arrangement of the polymer backbone and cation-tethered alkyl chains. The results demonstrate that the microstructure and morphology of these polymeric membranes significantly influence ion conductivity and fuel cell performance. Finally, the results of this study provide new insights that will guide the molecular design ofmore » polymer electrolyte materials to improve fuel cell performance.« less

Effects of Annular Electromagnetic Stirring Coupled with Intercooling on Grain Refinement and Homogeneity During Direct Chill Casting of Large-Sized 7005 Alloy Billet

NASA Astrophysics Data System (ADS)

Luo, Yajun; Zhang, Zhifeng; Li, Bao; Gao, Mingwei; Qiu, Yang; He, Min

2017-12-01

To obtain a large-sized, high-quality aluminum alloy billet, an advanced uniform direct chill (UDC) casting method was developed by combining annular electromagnetic stirring (A-EMS) with intercooling in the sump. The 7005 alloy was chosen to investigate the effect of UDC on grain refinement and homogeneity during normal direct chill (NDC) casting. It was concluded that the microstructure consisting of both primary α-Al phase and secondary phases becomes finer and more homogeneous for the billets prepared with UDC casting compared to those prepared with NDC casting, and the forced cooling from both the inner and outer melt under A-EMS has a measurable effect on grain refinement and homogeneity.

2D automatic body-fitted structured mesh generation using advancing extraction method

NASA Astrophysics Data System (ADS)

Zhang, Yaoxin; Jia, Yafei

2018-01-01

This paper presents an automatic mesh generation algorithm for body-fitted structured meshes in Computational Fluids Dynamics (CFD) analysis using the Advancing Extraction Method (AEM). The method is applicable to two-dimensional domains with complex geometries, which have the hierarchical tree-like topography with extrusion-like structures (i.e., branches or tributaries) and intrusion-like structures (i.e., peninsula or dikes). With the AEM, the hierarchical levels of sub-domains can be identified, and the block boundary of each sub-domain in convex polygon shape in each level can be extracted in an advancing scheme. In this paper, several examples were used to illustrate the effectiveness and applicability of the proposed algorithm for automatic structured mesh generation, and the implementation of the method.

Trans-dimensional Bayesian inversion of airborne electromagnetic data for 2D conductivity profiles

NASA Astrophysics Data System (ADS)

Hawkins, Rhys; Brodie, Ross C.; Sambridge, Malcolm

2018-02-01

This paper presents the application of a novel trans-dimensional sampling approach to a time domain airborne electromagnetic (AEM) inverse problem to solve for plausible conductivities of the subsurface. Geophysical inverse field problems, such as time domain AEM, are well known to have a large degree of non-uniqueness. Common least-squares optimisation approaches fail to take this into account and provide a single solution with linearised estimates of uncertainty that can result in overly optimistic appraisal of the conductivity of the subsurface. In this new non-linear approach, the spatial complexity of a 2D profile is controlled directly by the data. By examining an ensemble of proposed conductivity profiles it accommodates non-uniqueness and provides more robust estimates of uncertainties.

Bandwidth based methodology for designing a hybrid energy storage system for a series hybrid electric vehicle with limited all electric mode

NASA Astrophysics Data System (ADS)

Shahverdi, Masood

The cost and fuel economy of hybrid electrical vehicles (HEVs) are significantly dependent on the power-train energy storage system (ESS). A series HEV with a minimal all-electric mode (AEM) permits minimizing the size and cost of the ESS. This manuscript, pursuing the minimal size tactic, introduces a bandwidth based methodology for designing an efficient ESS. First, for a mid-size reference vehicle, a parametric study is carried out over various minimal-size ESSs, both hybrid (HESS) and non-hybrid (ESS), for finding the highest fuel economy. The results show that a specific type of high power battery with 4.5 kWh capacity can be selected as the winning candidate to study for further minimization. In a second study, following the twin goals of maximizing Fuel Economy (FE) and improving consumer acceptance, a sports car class Series-HEV (SHEV) was considered as a potential application which requires even more ESS minimization. The challenge with this vehicle is to reduce the ESS size compared to 4.5 kWh, because the available space allocation is only one fourth of the allowed battery size in the mid-size study by volume. Therefore, an advanced bandwidth-based controller is developed that allows a hybridized Subaru BRZ model to be realized with a light ESS. The result allows a SHEV to be realized with 1.13 kWh ESS capacity. In a third study, the objective is to find optimum SHEV designs with minimal AEM assumption which cover the design space between the fuel economies in the mid-size car study and the sports car study. Maximizing FE while minimizing ESS cost is more aligned with customer acceptance in the current state of market. The techniques applied to manage the power flow between energy sources of the power-train significantly affect the results of this optimization. A Pareto Frontier, including ESS cost and FE, for a SHEV with limited AEM, is introduced using an advanced bandwidth-based control strategy teamed up with duty ratio control. This controller allows the series hybrid's advantage of tightly managing engine efficiency to be extended to lighter ESS, as compared to the size of the ESS in available products in the market.

Absorbable energy monitoring scheme: new design protocol to test vehicle structural crashworthiness.

PubMed

Ofochebe, Sunday M; Enibe, Samuel O; Ozoegwu, Chigbogu G

2016-05-01

In vehicle crashworthiness design optimization detailed system evaluation capable of producing reliable results are basically achieved through high-order numerical computational (HNC) models such as the dynamic finite element model, mesh-free model etc. However the application of these models especially during optimization studies is basically challenged by their inherent high demand on computational resources, conditional stability of the solution process, and lack of knowledge of viable parameter range for detailed optimization studies. The absorbable energy monitoring scheme (AEMS) presented in this paper suggests a new design protocol that attempts to overcome such problems in evaluation of vehicle structure for crashworthiness. The implementation of the AEMS involves studying crash performance of vehicle components at various absorbable energy ratios based on a 2DOF lumped-mass-spring (LMS) vehicle impact model. This allows for prompt prediction of useful parameter values in a given design problem. The application of the classical one-dimensional LMS model in vehicle crash analysis is further improved in the present work by developing a critical load matching criterion which allows for quantitative interpretation of the results of the abstract model in a typical vehicle crash design. The adequacy of the proposed AEMS for preliminary vehicle crashworthiness design is demonstrated in this paper, however its extension to full-scale design-optimization problem involving full vehicle model that shows greater structural detail requires more theoretical development.

Continental and marine surficial water - groundwater interactions: the case of the southern coastland of Venice (Italy)

NASA Astrophysics Data System (ADS)

Tosi, Luigi; Da Lio, Cristina; Teatini, Pietro; Menghini, Antonio; Viezzoli, Andrea

2018-06-01

Understanding the continental-marine surficial water-groundwater exchanges in transitional coastal environments is really challenging at large scale. It requires an image of the saltwater-freshwater relationship which is difficult to be obtained especially in wetlands, lagoons, and marine areas. This study is focused on the coastland of the southern Venice lagoon - northern Po river delta (Italy), a precarious environment subject to both natural changes and anthropogenic pressures. Here, saltwater severely affects farmlands and aquifers. We used an airborne electromagnetics (AEM) survey with the goal of characterizing the continental and marine surficial water-groundwater interactions in such coastal region. The AEM survey allowed depicting a clear image of the fresh water-saltwater occurrence in shallow aquifers along mainland-lagoon - littoral-sea profiles, up to 20 km long. The results reveal that continental groundwater is located in the lagoon subsoil below a 10-20 m thick saline aquifer and extends down to 70 m depth. The whole low-lying farmland located south of the lagoon margin is seriously affected by saltwater contamination, which occurs from a few to about 50 m depth. The integrated analysis of AEM, seismic and borehole data shows that buried morpho-geological structures, such as paleo-channels and over-consolidated clay units control the saline contamination from the lagoon and the sea into the coastal aquifer system.

Phase separation and ion conductivity in the bulk and at the surface of anion exchange membranes with different ion exchange capacities at different humidities

NASA Astrophysics Data System (ADS)

Kimura, Taro; Akiyama, Ryo; Miyatake, Kenji; Inukai, Junji

2018-01-01

For higher performances of anion exchange membrane (AEM) fuel cells, understanding the phase-separated structures inside AEMs is essential, as well as those at the catalyst layer/membrane interfaces. The AEMs based on quaternized aromatic semi-block copolymers with different ion exchange capacities (IECs) were systematically investigated. With IECs of 1.23 and 1.95 mequiv g-1, the water uptakes at room temperature were 37% and 98%, and the anion conductivities 23.6 and 71.4 mS cm-1, respectively. The increases were not proportional to the IEC. Images obtained by transmission electron microscopy in vacuum were similar with both IEC values, but the development of a clear phase separation in humidified nitrogen was observed in the profiles only with 1.95 mequiv g-1obtained by small-angle X-ray scattering. At the temperature of 40 °C and the relative humidity (RH) of 30%, the average currents observed at the tip apex by current-sensing atomic force microscopy were <0.5 and 10 pA with 1.23 and 1.95 mequiv g-1, respectively, and those at 70% RH were 10 and 15 pA, respectively. The humidity gave a larger influence on the bulk structure with 1.95 mequiv g-1, whereas a larger influence on the surface conductivity with 1.23 mequiv g-1.

Anion exchange membrane crosslinked in the easiest way stands out for fuel cells

NASA Astrophysics Data System (ADS)

Hossain, Md. Masem; Wu, Liang; Liang, Xian; Yang, Zhengjin; Hou, Jianqiu; Xu, Tongwen

2018-06-01

Covalent crosslinking is an effective method to stabilize anion exchange membranes (AEMs) against water swelling and high alkaline environment, yet complicated process is required. We report herein a straightforward approach to prepare highly crosslinked, transparent and flexible AEM by simply immersing a halo-alkylated polymer (e.g., brominated poly-(2,6-dimethyl-phenylene oxide)) based membrane in aqueous dimethylamine solution at room temperature and the following methylation. During this crosslinking process, a robust self-crosslinking network is formed which shows a gel fraction in N-methyl-2-pyrrolidone of (up to) 94%. Self-crosslinked membranes show low water uptakes (20-42%) and dimensional swelling (9-16%) compared to non-crosslinked membrane but good hydroxide conductivities (up to 26 mS cm-1) at room temperature. Besides, the resulting membranes show some interesting features: the membranes do not immensely change its room temperature water swelling properties at high temperature but exhibits good hydroxide conductivities (up to 60 mS cm-1 at 80 °C). Noting that, the self-crosslinked AEM reported here has no β-hydrogens, exhibiting extremely high alkaline stability (no decline in hydroxide conductivity in 1 M KOH at 60 °C for 360h). Membrane electrode assembly consists of fabricated membrane shows moderate fuel cell performance reaching peak power density 31 mW cm-2 at 60 °C in a H2/O2 alkaline fuel cell.

The Electronic Structures and Optical Properties of Alkaline-Earth Metals Doped Anatase TiO2: A Comparative Study of Screened Hybrid Functional and Generalized Gradient Approximation

PubMed Central

Ma, Jin-Gang; Zhang, Cai-Rong; Gong, Ji-Jun; Wu, You-Zhi; Kou, Sheng-Zhong; Yang, Hua; Chen, Yu-Hong; Liu, Zi-Jiang; Chen, Hong-Shan

2015-01-01

Alkaline-earth metallic dopant can improve the performance of anatase TiO2 in photocatalysis and solar cells. Aiming to understand doping mechanisms, the dopant formation energies, electronic structures, and optical properties for Be, Mg, Ca, Sr, and Ba doped anatase TiO2 are investigated by using density functional theory calculations with the HSE06 and PBE functionals. By combining our results with those of previous studies, the HSE06 functional provides a better description of electronic structures. The calculated formation energies indicate that the substitution of a lattice Ti with an AEM atom is energetically favorable under O-rich growth conditions. The electronic structures suggest that, AEM dopants shift the valence bands (VBs) to higher energy, and the dopant-state energies for the cases of Ca, Sr, and Ba are quite higher than Fermi levels, while the Be and Mg dopants result into the spin polarized gap states near the top of VBs. The components of VBs and dopant-states support that the AEM dopants are active in inter-band transitions with lower energy excitations. As to optical properties, Ca/Sr/Ba are more effective than Be/Mg to enhance absorbance in visible region, but the Be/Mg are superior to Ca/Sr/Ba for the absorbance improvement in near-IR region. PMID:28793520

The Electronic Structures and Optical Properties of Alkaline-Earth Metals Doped Anatase TiO2: A Comparative Study of Screened Hybrid Functional and Generalized Gradient Approximation.

PubMed

Ma, Jin-Gang; Zhang, Cai-Rong; Gong, Ji-Jun; Wu, You-Zhi; Kou, Sheng-Zhong; Yang, Hua; Chen, Yu-Hong; Liu, Zi-Jiang; Chen, Hong-Shan

2015-08-24

Alkaline-earth metallic dopant can improve the performance of anatase TiO2 in photocatalysis and solar cells. Aiming to understand doping mechanisms, the dopant formation energies, electronic structures, and optical properties for Be, Mg, Ca, Sr, and Ba doped anatase TiO2 are investigated by using density functional theory calculations with the HSE06 and PBE functionals. By combining our results with those of previous studies, the HSE06 functional provides a better description of electronic structures. The calculated formation energies indicate that the substitution of a lattice Ti with an AEM atom is energetically favorable under O-rich growth conditions. The electronic structures suggest that, AEM dopants shift the valence bands (VBs) to higher energy, and the dopant-state energies for the cases of Ca, Sr, and Ba are quite higher than Fermi levels, while the Be and Mg dopants result into the spin polarized gap states near the top of VBs. The components of VBs and dopant-states support that the AEM dopants are active in inter-band transitions with lower energy excitations. As to optical properties, Ca/Sr/Ba are more effective than Be/Mg to enhance absorbance in visible region, but the Be/Mg are superior to Ca/Sr/Ba for the absorbance improvement in near-IR region.

Analytical electron microscopy in the study of biological systems.

PubMed

Johnson, D E

1986-01-01

The AEM is a powerful tool in biological research, capable of providing information simply not available by other means. The use of a field emission STEM for this application can lead to a significant improvement in spatial resolution in most cases now allowed by the quality of the specimen preparation but perhaps ultimately limited by the effects of radiation damage. Increased elemental sensitivity is at least possible in selected cases with electron energy-loss spectrometry, but fundamental aspects of ELS will probably confine its role to that of a limited complement to EDS. The considerable margin for improvement in sensitivity of the basic analytical technique means that the search for technological improvement will continue. Fortunately, however, current technology can also continue to answer important biological questions.

Developments in Surge Research Priorities: A Systematic Review of the Literature Following the Academic Emergency Medicine Consensus Conference, 2007-2015.

PubMed

Morton, Melinda J; DeAugustinis, Matthew L; Velasquez, Christina A; Singh, Sonal; Kelen, Gabor D

2015-11-01

In 2006, Academic Emergency Medicine (AEM) published a special issue summarizing the proceedings of the AEM consensus conference on the "Science of Surge." One major goal of the conference was to establish research priorities in the field of "disasters" surge. For this review, we wished to determine the progress toward the conference's identified research priorities: 1) defining criteria and methods for allocation of scarce resources, 2) identifying effective triage protocols, 3) determining decision-makers and means to evaluate response efficacy, 4) developing communication and information sharing strategies, and 5) identifying methods for evaluating workforce needs. Specific criteria were developed in conjunction with library search experts. PubMed, Embase, Web of Science, Scopus, and the Cochrane Library databases were queried for peer-reviewed articles from 2007 to 2015 addressing scientific advances related to the above five research priorities identified by AEM consensus conference. Abstracts and foreign language articles were excluded. Only articles with quantitative data on predefined outcomes were included; consensus panel recommendations on the above priorities were also included for the purposes of this review. Included study designs were randomized controlled trials, prospective, retrospective, qualitative (consensus panel), observational, cohort, case-control, or controlled before-and-after studies. Quality assessment was performed using a standardized tool for quantitative studies. Of the 2,484 unique articles identified by the search strategy, 313 articles appeared to be related to disaster surge. Following detailed text review, 50 articles with quantitative data and 11 concept papers (consensus conference recommendations) addressed at least one AEM consensus conference surge research priority. Outcomes included validation of the benchmark of 500 beds/million of population for disaster surge capacity, effectiveness of simulation- and Internet-based tools for forecasting of hospital and regional demand during disasters, effectiveness of reverse triage approaches, development of new disaster surge metrics, validation of mass critical care approaches (altered standards of care), use of telemedicine, and predictions of optimal hospital staffing levels for disaster surge events. Simulation tools appeared to provide some of the highest quality research. Disaster simulation studies have arguably revolutionized the study of disaster surge in the intervening years since the 2006 AEM Science of Surge conference, helping to validate some previously known disaster surge benchmarks and to generate new surge metrics. Use of reverse triage approaches and altered standards of care, as well as Internet-based tools such as Google Flu Trends, have also proven effective. However, there remains significant work to be done toward standardizing research methodologies and outcomes, as well as validating disaster surge metrics. © 2015 by the Society for Academic Emergency Medicine.

A conceptual model for groundwater - surface water interactions in the Darling River Floodplain, N.S.W., Australia

NASA Astrophysics Data System (ADS)

Brodie, R. S.; Lawrie, K.; Somerville, P.; Hostetler, S.; Magee, J.; Tan, K. P.; Clarke, J.

2013-12-01

Multiple lines of evidence were used to develop a conceptual model for interaction between the Darling River and associated floodplain aquifers in western New South Wales, Australia. Hydrostratigraphy and groundwater salinities were mapped using airborne electromagnetics (AEM), validated by sonic-core drilling. The AEM was highly effective in mapping groundwater freshening due to river leakage in discrete zones along the river corridor. These fresh resources occurred in both the unconfined Quaternary aquifers and the underlying, largely semi-confined Pliocene aquifers. The AEM was also fundamental to mapping the Blanchetown Clay aquitard which separates these two aquifer systems. Major-ion chemistry highlighted a mixing signature between river waters and groundwaters in both the Quaternary and Pliocene aquifers. Stable isotope data indicates that recharge to the key Pliocene aquifers is episodic and linked to high-flow flood events rather than river leakage being continuous. This was also evident when groundwater chemistry was compared with river chemistry under different flow conditions. Mapping of borehole levels showed groundwater mounding near the river, emphasising the regional significance of losing river conditions for both aquifer systems. Critically, rapid and significant groundwater level responses were measured during large flood events. In the Pliocene aquifers, continuation of rising trends after the flood peak receded confirms that this is an actual recharge response rather than hydraulic loading. The flow dependency of river leakage can be explained by the presence of mud veneers and mineral precipitates along the Darling River channel bank when river flows are low. During low flow conditions these act as impediments to river leakage. During floods, high flow velocities scour these deposits, revealing lateral-accretion surfaces in the shallow scroll plain sediments. This scouring allows lateral bank recharge to the shallow aquifer. During flood recession, mud veneers are re-deposited while transient return flows from bank storage results in carbonate precipitation in river banks. Active recharge of the Pliocene aquifers requires leakage pathways through the overlying Blanchetown Clay. Neogene-to-Present tectonic modification of the alluvial sequence, including discrete fault offsets in the Blanchetown Clay, was identified in the AEM data. Mapped faults are coincident with structures mapped in LiDAR, airborne magnetics, regional gravity, and seismic data.The study highlighted the utility of AEM in mapping the critical geological controls on groundwater-surface interaction, including the previously unrecognised tectonic influences on the largely unconsolidated alluvial sequence. Flow-dependent recharge due to changing river bed conductance has implications for groundwater assessment and management. An analysis of historic river flows suggests that active recharge would only occur for about 17% of the time when flow exceeds about 9,000 ML/d. Recharge would be negligible with groundwater extraction during low-flow conditions.

Towards AEM bathymetry and conductivity estimation in very shallow hypersaline waters of the Coorong, South Australia

NASA Astrophysics Data System (ADS)

Vrbancich, Julian

2013-01-01

The Coorong is a shallow (typically 1.5m) narrow coastal lagoon extending ~110km parallel to the coastline, and forms an extensive wetland area of international significance. It is divided into two lagoons, the North and South lagoons. The northern lagoon section opens into the mouth of the Murray River and the southern lagoon section is essentially closed, being connected to the North Lagoon via a choke point. During periods of extended drought where there is no flooding to flush the lagoon system, hypersalinisation gradually increases, especially in the southern lagoon section where salinity may be in excess of four times that of seawater. A helicopter time-domain EM (TEM) system was flown along the Coorong, as extensive flood waters from Queensland (2010) were reaching the North Lagoon lowering the salinity. The derived bathymetry from TEM data was shown to be in fair agreement with known bathymetry in areas of high salinity. The conductivities of waters ranging from saline to hypersaline in the North Lagoon and upper half of the South Lagoon, and underlying sediment, was estimated from inversion of TEM data using the known water depth as a fixed parameter. The derived conductivity varied from ~1.6S/m in the north of the North Lagoon to ~8-10S/m at its southern end and in the South Lagoon. These values underestimate the known strong salinity gradient (~0.6 to ~13S/m respectively) observed from a sparse distribution of fixed conductivity meters located in the Coorong. The application of AEM in this region is challenging because of the very large range of water conductivities and because the average water depths are comparable to the typical residuals between known depths and depths derived from AEM data in previous studies in Australian coastal waters. These results do however show that AEM has the potential to remotely map shallow water depths, and water conductivity gradients using known bathymetry to monitor hypersalinisation in these significant wetland areas where changes in the ecology have been linked to high salinity.

Airborne Geophysical Surveys Applied to Hydrocarbon Resource Development Environmental Studies

NASA Astrophysics Data System (ADS)

Smith, B. D.; Ball, L. B.; Finn, C.; Kass, A.; Thamke, J.

2014-12-01

Application of airborne geophysical surveys ranges in scale from detailed site scale such as locating abandoned well casing and saline water plumes to landscape scale for mapping hydrogeologic frameworks pertinent to ground water and tectonic settings relevant to studies of induced seismicity. These topics are important in understanding possible effects of hydrocarbon development on the environment. In addition airborne geophysical surveys can be used in establishing baseline "snapshots", to provide information in beneficial uses of produced waters, and in mapping ground water resources for use in well development. The U.S. Geological Survey (USGS) has conducted airborne geophysical surveys over more than 20 years for applications in energy resource environmental studies. A majority of these surveys are airborne electromagnetic (AEM) surveys to map subsurface electrical conductivity related to plumes of saline waters and more recently to map hydrogeologic frameworks for ground water and plume migration. AEM surveys have been used in the Powder River Basin of Wyoming to characterize the near surface geologic framework for siting produced water disposal ponds and for beneficial utilization in subsurface drip irrigation. A recent AEM survey at the Fort Peck Reservation, Montana, was used to map both shallow plumes from brine pits and surface infrastructure sources and a deeper concealed saline water plume from a failed injection well. Other reported applications have been to map areas geologically favorable for shallow gas that could influence drilling location and design. Airborne magnetic methods have been used to image the location of undocumented abandoned well casings which can serve as conduits to the near surface for coproduced waters. They have also been used in conjunction with geologic framework studies to understand the possible relationships between tectonic features and induced earthquakes in the Raton Basin. Airborne gravity as well as developing deeper mapping AEM surveys could also be effectively used in mapping tectonic features. Airborne radiometric methods have not been routinely used in hydrocarbon environmental studies but might be useful in understanding the surficial distribution of deposits related to naturally occurring radioactive materials.

Biofiltration of Volatile Pollutants: Solubility Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.; Barton, John W.

2001-06-15

This project investigates and collects fundamental partitioning data for a variety of sparingly soluble subsurface contaminants (e.g., TCE, etc.) between vapor, aqueous phase, and matrices containing substantial quantities of biomass and biomass components. Due to the difficulty of obtaining these measurements, environmental models have generally used solubility constants of chemicals in pure water or, in a few rare cases, simple linear models. Our prior EMSP work has shown that the presence of biological material can increase effective solubilities by an order of magnitude for sparingly soluble organics; therefore, the previous simple approaches are not valid and are extremely poor predictorsmore » of actual bio-influenced partitioning. It is likely that environmental contaminants will partition in a similar manner into high-biomass phases (e.g. biobarriers and plants) or humic soils. Biological material in the subsurface can include lipids, fatty acids, humic materials, as well a s the lumped and difficult to estimate 'biomass'. Our measurements include partition into these biological materials to allow better estimation. Fundamental data collected will be used in mathematical models predicting transport and sorption in subsurface environments, with the impacts on bioremediation being evaluated based on this new information. Our 2-D Win95/98 software program, Biofilter 1.0, developed as a part of our prior EMSP efforts for describing biofiltration processes with consideration given to both kinetic and mass transfer factors, will be extended to incorporate and use this information.« less

Biofiltration of Volatile Pollutants: Solubility Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, Brian H.; Barton, John W.

2002-06-15

This project investigates and collects fundamental partitioning data for a variety of sparingly soluble subsurface contaminants (e.g., TCE, etc.) between vapor, aqueous phase, and matrices containing substantial quantities of biomass and biomass components. Due to the difficulty of obtaining these measurements, environmental models have generally used solubility constants of chemicals in pure water or, in a few rare cases, simple linear models. Our prior EMSP work has shown that the presence of biological material can increase effective solubilities by an order of magnitude for sparingly soluble organics; therefore, the previous simple approaches are not valid and are extremely poor predictorsmore » of actual bio-influenced partitioning. It is likely that environmental contaminants will partition in a similar manner into high-biomass phases (e.g. biobarriers and plants) or humic soils. Biological material in the subsurface can include lipids, fatty acids, humic materials, as well as the lumped and difficult-to-estimate 'biomass'. Our measurements include partition into these biological materials to allow better estimation. Fundamental data collected will be used in mathematical models predicting transport and sorption in subsurface environments, with the impacts on bioremediation being evaluated based on this new information. Our 2-D Win95/98/XP software program, Biofilter 1.0, developed as a part of our prior EMSP efforts for describing biofiltration processes with consideration given to both kinetic and mass transfer factors, is being extended to incorporate and use this information.« less

Colonial Spanish America, The Burbon Period

ERIC Educational Resources Information Center

Barbier, Jacques A.; Burkholder, Mark A.

1987-01-01

Provides an extensive annotated bibliography of materials on 18th century Latin America. The bibliography is divided into three sections: An introductory overview; selected topics such as The Enlightenment and women; and major regions. (AEM)

Semiautomatic mapping of permafrost in the Yukon Flats, Alaska

NASA Astrophysics Data System (ADS)

Gulbrandsen, Mats Lundh; Minsley, Burke J.; Ball, Lyndsay B.; Hansen, Thomas Mejer

2016-12-01

Thawing of permafrost due to global warming can have major impacts on hydrogeological processes, climate feedback, arctic ecology, and local environments. To understand these effects and processes, it is crucial to know the distribution of permafrost. In this study we exploit the fact that airborne electromagnetic (AEM) data are sensitive to the distribution of permafrost and demonstrate how the distribution of permafrost in the Yukon Flats, Alaska, is mapped in an efficient (semiautomatic) way, using a combination of supervised and unsupervised (machine) learning algorithms, i.e., Smart Interpretation and K-means clustering. Clustering is used to sort unfrozen and frozen regions, and Smart Interpretation is used to predict the depth of permafrost based on expert interpretations. This workflow allows, for the first time, a quantitative and objective approach to efficiently map permafrost based on large amounts of AEM data.

Semiautomatic mapping of permafrost in the Yukon Flats, Alaska

USGS Publications Warehouse

Gulbrandsen, Mats Lundh; Minsley, Burke J.; Ball, Lyndsay B.; Hansen, Thomas Mejer

2016-01-01

Thawing of permafrost due to global warming can have major impacts on hydrogeological processes, climate feedback, arctic ecology, and local environments. To understand these effects and processes, it is crucial to know the distribution of permafrost. In this study we exploit the fact that airborne electromagnetic (AEM) data are sensitive to the distribution of permafrost and demonstrate how the distribution of permafrost in the Yukon Flats, Alaska, is mapped in an efficient (semiautomatic) way, using a combination of supervised and unsupervised (machine) learning algorithms, i.e., Smart Interpretation and K-means clustering. Clustering is used to sort unfrozen and frozen regions, and Smart Interpretation is used to predict the depth of permafrost based on expert interpretations. This workflow allows, for the first time, a quantitative and objective approach to efficiently map permafrost based on large amounts of AEM data.

Effect of AEM energy applicator configuration on magnetic nanoparticle mediated hyperthermia for breast cancer.

PubMed

Sanapala, Krishna K; Hewaparakrama, Kapila; Kang, Kyung A

2011-01-01

Magnetic nanoparticle mediated low heat hyperthermia (42~45( o )C) via alternating electromagnetic (AEM) energy is a promising, cancer specific and minimally-invasive cancer therapy. Iron oxide particles frequently used for this therapy are non-toxic and already used as a contrast agent for magnetic resonance imaging. One important issue in the hyperthermia is applying an appropriate amount of energy to the tumor at various sizes and depths, with a minimal damage to normal tissue. For the therapy to be desirable, the AEM energy applicator needs to be non-invasive and user-friendly. To better understand the effect of the probe on the magnetic field distribution, computer simulation was performed for the field distribution by probes with various configurations. In a solenoid-type probe, the field is mainly inside the probe and, therefore, is difficult to use on body. A pancake-shaped probe is easy to use but the field penetration is shallow and, thus, may better serve surface tumor treatment. A sandwich probe, composed of two pancake probes, has a penetration depth deeper than a pancake probe. The results also showed that the spacing between two adjacent coils and the number of coil turns are very important for controlling the field penetration depth and strength. Experiments were also performed to study the effects of the size and concentration of iron oxide nanoparticles on heating. Among the tested particle sizes of 10~50 nm, 30 nm particles showed the best heating for the same mass.

Technologies For Maintaining Animals In Space: Lighting, Air Quality, Noise, Food And Water

NASA Technical Reports Server (NTRS)

Winget, C. M.; Skidmore, M. G.; Holley, D. C.; Dalton, Bonnie P. (Technical Monitor)

1995-01-01

In the terrestrial environment multiple time cues exist. Zeitgebers have been identified and studied for their ability to convey temporal information to various physiological systems. In the microgravity experiment it is necessary to define time cues within the flight hardware prior to flight. During flight if changes in the Circadian System (e.g., mean, phase angle, period) occur this would indicate that the gravity vector is important relative to biological timing. This presentation is concerned with the environmental parameter: to support rodent experiments in microgravity. The Animal Enclosure Module (AEM) provides solid food bars and water via lixits and ad libitum. Flight animals (Sprague-Dawley rats, 60 - 300g) when compared to ground controls show similar growth (mean growth per day g, plus or minus SD; flight 5.4 plus or minus 2.0, ground 5.9 plus or minus 2.1). Current AEMs use incandescent lighting (approx. 5 Lux). Light emitting diode (LED) arrays are being developed that provide a similar light environment as cool-white fluorescent sources (40 Lux). In ground based tests (12L:12D), these arrays show normal circadian entrainment (Tau = 24.0) with respect to the behavioral responses, measured (drinking, eating, gross locomotor activity). A newly developed ultra high efficiency filter system can entrap all feces, urine and odors from 6 rats for 24 days. Maximum sound level exposure limits (per octave band 22 Hz - 179 kHz) have been established. The AEM will effectively support animal experiments in microgravity.

Technologies for Maintaining Animals in Space: Lighting, Air Quality, Noise, Food and Water

NASA Technical Reports Server (NTRS)

Winget, C. M.; Skidmore, M. G.; Holley, D. C.; Dalton, Bonnie P. (Technical Monitor)

1995-01-01

In the terrestrial environment multiple time cues exist. Zeitgebers have been identified and studied for their ability to convey temporal information to various physiological systems, In the microgravity experiment it is necessary to define time cues within the flight hardware prior to flight. During flight if changes in the Circadian System (e.g., mean, phase angle, period) occur this would indicate that the gravity vector is important relative to biological timing. This presentation is concerned with the environmental parameters to support rodent experiments in microgravity. The Animal Enclosure Module (AEM) provides solid food bars and water via lixits ad libitum. Flight animals (Sprague-Dawley rats, 60 - 300g) when compared to ground controls show similar growth (mean growth per day, g +/- SD; flight 5.4 +/- 2.0, ground 5.9 +/- 2.1). Current AEMs use incandescent lighting (approx. 5 Lux). Light emitting diode (LED) arrays are being developed that provide a similar light environment as cool-white fluorescent sources (40 Lux). In ground based tests (12L:12D), these arrays show normal circadian entrainment (Tau = 24.0) with respect to the behavioral responses. measured (drinking, eating, gross locomotor activity). A newly developed ultra high efficiency filter system can entrap all feces, urine and odors from 6 rats for 24 days. Maximum sound level exposure limits (per octave band 22 Hz - 179 kHz) have been established. The AEM will effectively support animal experiments in microgravity.

Lactating Rats Retain Nursing Behavior and Maternal Care in Space

NASA Technical Reports Server (NTRS)

Daly, Megan E.; Ronca, April E.; Dalton, Bonnie (Technical Monitor)

2001-01-01

In 1997, suckling mammals were flown in space for the first time as part of the NIH.R3 experiment sponsored jointly by NIH (National Institutes of Health) and NASA. Six rat dams and litters (Rattus norvegicus) were launched on an eight-day Space Shuttle mission at each of three postnatal ages (P5, P8, and P15). Dams and litters (N = 10 pups/litter) were housed within modified Animal Enclosure Modules (AEMs). Comparisons were made to ground controls. Dams and litters were videotaped daily in flight. The P8 and P15 flight litters showed excellent survival (99%) and weight gain relative to AEM ground controls, whereas P5 litters showed reduced survival (0% and 60%, respectively) and weight gain (less than 40% AEM). To examine the possibility that failures of maternal care contributed to P5 results, we analyzed the dams' in-flight nursing, licking and retrieving from four video segments ranging from twelve to fifteen minutes in length with control data derived from multiple ground segments. Video analyses revealed clear evidence of maternal care in flight. For P5 dams, frequency and duration of nursing and licking bouts fell within or above one standard deviation of control values. Retrieving was noted in the P5 and P8 groups only. The observed results suggest that factors other than maternal care contributed to the low survival rates and body weight gains of the P5 flight offspring.

Effect of double density caging during Space Shuttle transport of laboratory rats

NASA Technical Reports Server (NTRS)

Riskowski, G. L.; Gonyou, H. W.; Harrison, P. C.; Kelley, K. W.; Tumbleson, M. E.

1993-01-01

Male Sprague Dawley rats were housed in groups of four in polycarbonate cages at recommended density and thermal environmental conditions for 14 days prior to testing to ensure uniform acclimation to those conditions. Body weights averaged 286 +/- 7 g at the end of acclimation. Rat cages were assigned randomly to three treatments: (1) 4 rats/polycarbonate cage (877 sq cm, 20.3 cm high, 220 sq cm/rat), (2) 4 rats/mock AEM (MAEM) (620 sq cm, 155 sq cm/rat), and (3) 8 rats/MAEM (620 sq cm, 77.5 sq cm/rat). A comparison between the MAEM-DD and MAEM-SD treatments was done to determine if doubling rat density in AEM's stressed the rats. A comparison among MAEM treatments and the PC treatment was done to determine if any stress indications were due to the AEM. During this density challenge phase, all treatments were maintained at the same thermal environmental conditions (22.5 C and 50 percent RH) for 10 days. After the density challenge phase, half the rats from each group were sacrificed for body tissue and fluid analyses. The remaining half of the rats were housed at a density of 4 rats/cage in polycarbonate cages at normal thermal environmental conditions for an additional 10 days to determine if there were any differences in responses between treatments after a recovery period. The remaining rats were examined and sacrificed for body tissue and fluid analyses at the end of the recovery phase.

Film Reviews.

ERIC Educational Resources Information Center

Lance, Larry M.; Atwater, Lynn

1987-01-01

Reviews four Human Sexuality films and videos. These are: "Personal Decisions" (Planned Parenthood Federation of America, 1985); "The Touch Film" (Sterling Production, 1986); "Rethinking Rape" (Film Distribution Center, 1985); "Not A Love Story" (National Film Board of Canada, 1981). (AEM)

Effects of Polymer Structure and Relaxations on Ionic Conductivity in Anion Exchange Membranes with Quaternary Ammonium Functional Groups

NASA Astrophysics Data System (ADS)

Maes, Ashley M.

Anion exchange membranes (AEMs) are of considerable interest to developers and researchers of electrochemical conversion and storage devices such as anion exchange membrane fuel cells (AAEMFCs), alkaline polymer electrolyte electrolysers, redox flow batteries and bioelectrochemical devices. AEMs are generally in competition with more established proton exchange membranes (PEMs), but offer the potential for reduction of materials costs and greater fuel flexibility across these applications. This work includes an introduction to AEMs in the context of fuel cell technologies and some key techniques for AEM characterization. There are many synthetic strategies to incorporate cationic functional groups, which promote anion transport, into a polymer matrix. Two membrane chemistries are investigated in the following chapters. The first is based on a simple synthesis procedure that produced a membrane consisting of random, crosslinked polypropylene- ran-polyethyleneimine with quaternary ammonium functional groups. This membrane had moderate chloride ionic conductivity of 0.03 S cm -1 at 95 °C and high water uptake with minimal dimensional swelling. However, the lack of control of crosslink location and density during synthesis produced a material with a very random nature, making it a poor candidate for more fundamental transport studies. The second membrane chemistry is a block copolymer with a hydrophobic and hydrophilic block. The hydrophobic block was selected to provide favorable mechanical and barrier characteristics while a hydrophilic block was selected to provide water uptake and anion conducting functionalities. Poly(vinyl benzyl trimethyl ammonium bromide)-b-poly(methylbutylene) ([PVBTMA][Br]- b-PMB) was synthesized by partners at the University of Massachusetts-Amherst with varied degrees of functionalization (DF) along the hydrophilic block, resulting in ion exchange capacities ranging from 0.77 to 2.20 mmol g -1. Water uptake, in-plane ionic conductivity and membrane morphology were measured across a series of membranes with the original bromide (Br -) counter-ion. These bulk materials characterization experiments demonstrated that this polymer structure produces well-ordered lamellar morphology with moderate water uptake and competitive ionic conductivity (ca. 40 mS cm-1 at 90 °C and 95% relative humidity). These characteristics make it an appropriate candidate for the following more fundamental investigations of ionic conductivity mechanisms. Broadband electrical spectroscopy (BES) was conducted on one [PVBTMA][Br]- b-PMB sample in the Br- form and analyzed in conjunction with thermal stability and relaxation experiments in Chapter 4. We were able to propose two separate ionic conductivity mechanisms and relate each to physical attributes of the polymer structure. A significant thermal transition was observed at Tdelta , which resulted in a dramatic drop in conductivity. In a continued effort to characterize the ionic conductivity of these block-copolymer membranes, another BES study was conducted on three samples with varying DFs. Samples were converted to hydroxide (OH- ) form so we could contrast the Br- conductivity mechanisms to those in a more relevant counter-ion form. After analysis of the electric response of the material, combined with the thermal analysis by TGA, MDSC and DMA, conductivity mechanisms were described. As in the Br- study, conductivity involves two distinct conduction pathways, sigmaEP and sigmaIP,1. Importantly, we again observed a drop in conductivity at Tdelta in each of these samples, with Tdelta decreasing as the density of functional groups along the hydrophilic block increased. It is undesirable for this transition to occur during operation in a fuel cell or other electrochemical device, so future work to investigate strategies for inhibition are recommended.

Deep groundwater and potential subsurface habitats beneath an Antarctic dry valley

PubMed Central

Mikucki, J. A.; Auken, E.; Tulaczyk, S.; Virginia, R. A.; Schamper, C.; Sørensen, K. I.; Doran, P. T.; Dugan, H.; Foley, N.

2015-01-01

The occurrence of groundwater in Antarctica, particularly in the ice-free regions and along the coastal margins is poorly understood. Here we use an airborne transient electromagnetic (AEM) sensor to produce extensive imagery of resistivity beneath Taylor Valley. Regional-scale zones of low subsurface resistivity were detected that are inconsistent with the high resistivity of glacier ice or dry permafrost in this region. We interpret these results as an indication that liquid, with sufficiently high solute content, exists at temperatures well below freezing and considered within the range suitable for microbial life. These inferred brines are widespread within permafrost and extend below glaciers and lakes. One system emanates from below Taylor Glacier into Lake Bonney and a second system connects the ocean with the eastern 18 km of the valley. A connection between these two basins was not detected to the depth limitation of the AEM survey (∼350 m). PMID:25919365

Phosphoric acid fuel cell 1.3 MW plant in Milan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colombo, M.; Vigano, A.

1997-07-01

At the end of the 80`s Aem, ENEA and Ansaldo Ricerche began to design and build a 1.3 MW phosphoric-acid-fuel-cell power plant for the production of electrical power and heat; this plant was built and installed in the Bicocca site, in the north-east area of Milan, where a great development is being promoted. Aem has been taking over the plant since July 1995. Its aim is to test the extensively advantages of this technology for both conversion efficiency and low environmental impact. The experimentation will have to recognize the key elements in order to plan and create the multi-megawatt plantsmore » with the phosphoric acid technology, opening the experimentation to international partners, like users, industries and Universities interested in the development and the application of these new systems of energy cogeneration.« less

Crosslinked anion exchange membranes prepared from poly(phenylene oxide) (PPO) for non-aqueous redox flow batteries

NASA Astrophysics Data System (ADS)

Li, Yun; Sniekers, Jeroen; Malaquias, João C.; Van Goethem, Cedric; Binnemans, Koen; Fransaer, Jan; Vankelecom, Ivo F. J.

2018-02-01

A stable and eco-friendly anion-exchange membrane (AEM) was prepared and applied in a non-aqueous all-copper redox flow battery (RFB). The AEM was prepared via a simple procedure, leading to a cross-linked structure containing quaternary ammonium groups without involvement of harmful trimethylamine. A network was thus constructed which ensured both ion transport and solvent resistance. The ion exchange capacity (IEC) of the membrane was tuned from 0.49 to 1.03 meq g-1 by varying the content of the 4, 4‧-bipyridine crosslinking agent. The membrane showed a good anion conductivity and retention of copper ions. As a proof of principle, a RFB single cell with this crosslinked membrane yielded a coulombic efficiency of 89%, a voltage efficiency of 61% and an energy efficiency of 54% at 7.5 mA cm-2.

An Improved High-Sensitivity Airborne Transient Electromagnetic Sensor for Deep Penetration

PubMed Central

Chen, Shudong; Guo, Shuxu; Wang, Haofeng; He, Miao; Liu, Xiaoyan; Qiu, Yu; Zhang, Shuang; Yuan, Zhiwen; Zhang, Haiyang; Fang, Dong; Zhu, Jun

2017-01-01

The investigation depth of transient electromagnetic sensors can be effectively increased by reducing the system noise, which is mainly composed of sensor internal noise, electromagnetic interference (EMI), and environmental noise, etc. A high-sensitivity airborne transient electromagnetic (AEM) sensor with low sensor internal noise and good shielding effectiveness is of great importance for deep penetration. In this article, the design and optimization of such an AEM sensor is described in detail. To reduce sensor internal noise, a noise model with both a damping resistor and a preamplifier is established and analyzed. The results indicate that a sensor with a large diameter, low resonant frequency, and low sampling rate will have lower sensor internal noise. To improve the electromagnetic compatibility of the sensor, an electromagnetic shielding model for a central-tapped coil is established and discussed in detail. Previous studies have shown that unclosed shields with multiple layers and center grounding can effectively suppress EMI and eddy currents. According to these studies, an improved differential AEM sensor is constructed with a diameter, resultant effective area, resonant frequency, and normalized equivalent input noise of 1.1 m, 114 m2, 35.6 kHz, and 13.3 nV/m2, respectively. The accuracy of the noise model and the shielding effectiveness of the sensor have been verified experimentally. The results show a good agreement between calculated and measured results for the sensor internal noise. Additionally, over 20 dB shielding effectiveness is achieved in a complex electromagnetic environment. All of these results show a great improvement in sensor internal noise and shielding effectiveness. PMID:28106718

Simultaneous analyses of cocaine, cocaethylene, and their possible metabolic and pyrolytic products.

PubMed

Cardona, Patrick S; Chaturvedi, Arvind K; Soper, John W; Canfield, Dennis V

2006-02-10

A method was developed for simultaneously analyzing cocaine (COC), benzoylecgonine (BZE), norbenzoylecgonine (BNE), norcocaine (NCOC), ecgonine (ECG), ecgonine methyl ester (EME), m-hydroxybenzoylecgonine (HBZE), anhydroecgonine methyl ester (AEME), cocaethylene (CE), norcocaethylene (NCE), and ecgonine ethyl ester (EEE) in blood, urine, and muscle. Available deuterated analogs of these analytes were used as internal standards. Proteins from blood and muscle homogenate were precipitated with cold acetonitrile. After the removal of acetonitrile by evaporation, the supernatants and urine were subjected to solid-phase extraction. The eluted analytes were converted to their hydrochloride salts and derivatized with pentafluoropropionic anhydride and 2,2,3,3,3-pentafluoro-1-propanol. The derivatized products were analyzed by a gas chromatograph (GC)/mass spectrometer by selected ion monitoring. The limit of detection (LOD) for COC, BZE, NCOC, EME, CE, NCE, and EEE was 2ng/ml, while the LODs for BNE, ECG, HBZE, and AEME were 25, 640, 50, and 13 ng/ml, respectively. This method was successfully applied in analyzing 13 case samples from aviation accident pilot fatalities and motor vehicle operators. AEME concentrations found in the 13 samples were consistent with those produced solely by the GC inlet pyrolysis of COC controls in blood. Anhydroecgonine cannot be used as a marker for the abuse of COC by smoking because it is also pyrolytically produced from COC metabolites on the GC inlet. The developed method can be effectively adopted for analyzing COC and related compounds in urine, blood, and muscle by a single extraction with increased sensitivity through formation of hydrochloride salts and using a one-step derivatization.

Biological and metabolic response in STS-135 space-flown mouse skin.

PubMed

Mao, X W; Pecaut, M J; Stodieck, L S; Ferguson, V L; Bateman, T A; Bouxsein, M L; Gridley, D S

2014-08-01

There is evidence that space flight condition-induced biological damage is associated with increased oxidative stress and extracellular matrix (ECM) remodeling. To explore possible mechanisms, changes in gene expression profiles implicated in oxidative stress and in ECM remodeling in mouse skin were examined after space flight. The metabolic effects of space flight in skin tissues were also characterized. Space Shuttle Atlantis (STS-135) was launched at the Kennedy Space Center on a 13-day mission. Female C57BL/6 mice were flown in the STS-135 using animal enclosure modules (AEMs). Within 3-5 h after landing, the mice were euthanized and skin samples were harvested for gene array analysis and metabolic biochemical assays. Many genes responsible for regulating production and metabolism of reactive oxygen species (ROS) were significantly (p < 0.05) altered in the flight group, with fold changes >1.5 compared to AEM control. For ECM profile, several genes encoding matrix and metalloproteinases involved in ECM remodeling were significantly up-/down-regulated following space flight. To characterize the metabolic effects of space flight, global biochemical profiles were evaluated. Of 332 named biochemicals, 19 differed significantly (p < 0.05) between space flight skin samples and AEM ground controls, with 12 up-regulated and 7 down-regulated including altered amino acid, carbohydrate metabolism, cell signaling, and transmethylation pathways. Collectively, the data demonstrated that space flight condition leads to a shift in biological and metabolic homeostasis as the consequence of increased regulation in cellular antioxidants, ROS production, and tissue remodeling. This indicates that astronauts may be at increased risk for pathophysiologic damage or carcinogenesis in cutaneous tissue.

Phenotyping for patient safety: algorithm development for electronic health record based automated adverse event and medical error detection in neonatal intensive care.

PubMed

Li, Qi; Melton, Kristin; Lingren, Todd; Kirkendall, Eric S; Hall, Eric; Zhai, Haijun; Ni, Yizhao; Kaiser, Megan; Stoutenborough, Laura; Solti, Imre

2014-01-01

Although electronic health records (EHRs) have the potential to provide a foundation for quality and safety algorithms, few studies have measured their impact on automated adverse event (AE) and medical error (ME) detection within the neonatal intensive care unit (NICU) environment. This paper presents two phenotyping AE and ME detection algorithms (ie, IV infiltrations, narcotic medication oversedation and dosing errors) and describes manual annotation of airway management and medication/fluid AEs from NICU EHRs. From 753 NICU patient EHRs from 2011, we developed two automatic AE/ME detection algorithms, and manually annotated 11 classes of AEs in 3263 clinical notes. Performance of the automatic AE/ME detection algorithms was compared to trigger tool and voluntary incident reporting results. AEs in clinical notes were double annotated and consensus achieved under neonatologist supervision. Sensitivity, positive predictive value (PPV), and specificity are reported. Twelve severe IV infiltrates were detected. The algorithm identified one more infiltrate than the trigger tool and eight more than incident reporting. One narcotic oversedation was detected demonstrating 100% agreement with the trigger tool. Additionally, 17 narcotic medication MEs were detected, an increase of 16 cases over voluntary incident reporting. Automated AE/ME detection algorithms provide higher sensitivity and PPV than currently used trigger tools or voluntary incident-reporting systems, including identification of potential dosing and frequency errors that current methods are unequipped to detect. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Pseudomonas piscicida kills vibrios by two distinct mechanisms

USDA-ARS?s Scientific Manuscript database

Pseudoalteromonas piscicida is a naturally-occurring marine bacterium which kills competing bacteria, including vibrios. In studies by Richards et al. (AEM00175-17), three strains of P. piscicida were isolated and characterized. Strains secreted proteolytic enzymes which likely killed competing or...

Analytical electron microscope study of eight ataxites

NASA Technical Reports Server (NTRS)

Novotny, P. M.; Goldstein, J. I.; Williams, D. B.

1982-01-01

Optical and electron optical (SEM, TEM, AEM) techniques were employed to investigate the fine structure of eight ataxite-iron meteorites. Structural studies indicated that the ataxites can be divided into two groups: a Widmanstaetten decomposition group and a martensite decomposition group. The Widmanstaetten decomposition group has a Type I plessite microstructure and the central taenite regions contain highly dislocated lath martensite. The steep M shaped Ni gradients in the taenite are consistent with the fast cooling rates, of not less than 500 C/my, observed for this group. The martensite decomposition group has a Type III plessite microstructure and contains all the chemical group IVB ataxites. The maximum taenite Ni contents vary from 47.5 to 52.7 wt % and are consistent with slow cooling to low temperatures of not greater than 350 C at cooling rates of not greater than 25 C/my.

Characterization of glass-infiltrated alumina-based ceramics

PubMed Central

Bona, Alvaro Della; Mecholsky, John J; Barrett, Allyson A; Griggs, Jason A

2010-01-01

Objective characterize the microstructure, composition, and important properties of glass-infiltrated alumina-based ceramics similar to the In-Ceram system. Methods Materials used were: IA- In-Ceram Alumina (Vita); IAE- IA electrophoretically deposited (Vita); AEM- IA using a vacuum driven method (Vita); VC- Vitro-Ceram (Angelus); TC- Turkom-Cera (Turkom-Ceramic); CC- Ceramcap (Foto-Ceram); and AG- Alglass (EDG). Ceramic specimens were fabricated following manufacturers’ instructions and ISO6872 standard and polished successively through 1μm alumina abrasive. Semi-quantitative and qualitative analyses were performed using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and stereology (Vv). The elastic modulus (E) and Poisson’s ratio (ν) were determined using time-of-flight data measured in an ultrasonic pulser/receiver and the density (ρ) was determined using a helium pycnometer. Vicker’s indentation was used to calculate hardness (H). Bar specimens (25×4×1.2mm3) were loaded in three-point bending to fracture using a universal testing machine with cross-head speed of 1mm/min. Flexural strength (σ3P) was calculated and statistically analyzed using ANOVA, Tukey (α=0.05) and Weibull (m= modulus, σ0= characteristic strength). Results SEM and EDS analyses revealed similar microstructure for all ceramics, except for a lead-based matrix in CC and a zirconia phase in VC. TC, AG and CC showed significantly lower mean σ3P values than the other ceramics (p 0.05). AEM showed the greatest m (16). Conclusion Despite few differences in microstructure and composition, the IA, IAE, AEM and VC ceramics have similar properties. Significance The glass-infiltrated alumina-based ceramics from different manufacturers presented distinct characteristics. It is necessary to characterize new commercially available materials to understand their properties. PMID:18692231

Understanding Anion, Water, and Methanol Transport in a Polyethylene- b -poly(vinylbenzyl trimethylammonium) Copolymer Anion-Exchange Membrane for Electrochemical Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarode, Himanshu N.; Yang, Yuan; Motz, Andrew R.

Herein, we report the anion and water transport properties of an anion-exchange membrane (AEM) comprising a block copolymer of polyethylene and poly- (vinylbenzyl trimethylammonium) (PE-b-PVBTMA) with an ion-exchange capacity (IEC) of 1.08 mequiv/g. The conductivity varied little among the anions CO3 2-, HCO3 -, and F-, with a value of Ea ≈ 20 kJ/mol and a maximum fluoride conductivity of 34 mS/cm at 90 °C and 95% relative humidity. The Br- conductivity showed a transition at 60 °C. Pulsed gradient stimulated spin echo nuclear magnetic resonance (PGSE NMR) experiments showed that water diffusion in this AEM is heterogeneous and ismore » affected by the anion present, being fastest in the presence of F-. We determined the methanol self-diffusion in this membrane and observed that it is lower than that in Nafion 117, because of the lower water uptake. This article reports the first measurements of 13C-labeled bicarbonate self-diffusion in an AEM using PGSE NMR spectrometry, which was found to be significantly slower than F- self-diffusion. Back-calculation of the bicarbonate conductivity using the Nernst-Einstein equation gave a value that was significantly lower than the measured value, implying that bicarbonate transport involves OH- in the transport mechanism. Fourier transform infrared spectroscopy, PGSE NMR spectrometry, and small-angle X-ray scattering (SAXS) indicated the presence of different types of waters present in the membrane at different length scales. The SAXS data indicated that there is a water-rich region within the hydrophilic domains of the polymer that has a temperature dependence in intensity at 95% relative humidity (RH).« less

Pain-related avoidance versus endurance in primary care patients with subacute back pain: psychological characteristics and outcome at a 6-month follow-up.

PubMed

Hasenbring, Monika I; Hallner, Dirk; Klasen, Bernhard; Streitlein-Böhme, Irmgard; Willburger, Roland; Rusche, Herbert

2012-01-01

Recent research has found individual differences in back pain patients due to behavioral avoidance vs persistence. However, there is a lack of prospective studies of nonspecific low back pain patients. The avoidance-endurance model (AEM) suggests at least 3 pathways leading to chronic pain: fear-avoidance response, distress-endurance response, and eustress-endurance response. We sought to compare these 3 maladaptive subgroups with an adaptive group using a classification tool that included the following scales: the thought suppression and behavioral endurance subscale of the Avoidance-Endurance Questionnaire and the Beck Depression Inventory. The psychological characteristics, and pain and disability of the AEM subgroups were investigated. We report results from 177 patients with subacute nonspecific low back pain at the start of outpatient treatment and at follow-up after 6 months. At baseline, a multivariate analysis of variance found that the fear-avoidance patients scored higher in pain catastrophizing than the other groups. The distress-endurance patients displayed elevated anxiety/depression and helplessness/hopelessness accompanied with the highest scores in the classification variables thought suppression and persistence behavior. The eustress-endurance patients had the highest humor/distraction scores, pain persistence, and positive mood despite pain. All 3 maladaptive groups revealed a higher pain intensity than the adaptive patients at follow-up after 6 months; however, disability at follow-up was elevated only in the fear-avoidance and distress-endurance patients. The study provides preliminary evidence for the construct and prospective validity of AEM-based subgroups of subacute, nonspecific back pain patients. The results suggest the need for individually targeted cognitive behavioral treatments in the maladaptive groups. Copyright © 2011 International Association for the Study of Pain. Published by Elsevier B.V. All rights reserved.

Characterization of soil phosphorus in a fire-affected forest Cambisol by chemical extractions and (31)P-NMR spectroscopy analysis.

PubMed

Turrion, María-Belén; Lafuente, Francisco; Aroca, María-José; López, Olga; Mulas, Rafael; Ruipérez, Cesar

2010-07-15

This study was conducted to investigate the long-term effects of fire on soil phosphorus (P) and to determine the efficiency of different procedures in extracting soil P forms. Different P forms were determined: labile forms (Olsen-P, Bray-P, and P extracted by anion exchange membranes: AEM-P); moderately labile inorganic and organic P, obtained by NaOH-EDTA extraction after removing the AEM-P fraction; and total organic and inorganic soil P. (31)P-NMR spectroscopy was used to characterize the structure of alkali-soluble P forms (orthophosphate, monoester, pyrophosphate, and DNA). The studied area was a Pinus pinaster forest located at Arenas de San Pedro (southern Avila, Spain). The soils were Dystric Cambisols over granites. Soil samples were collected at 0-2 cm, 2-5 cm, and 10-15 cm depths, two years after a fire in the burned area and in an adjacent unburned forest area. Fire increased the total N, organic C, total P, and organic and inorganic P content in the surface soil layer. In burned soil, the P extracted by the sequential procedure (AEM and NaOH+EDTA) was about 95% of the total P. Bray extraction revealed a fire-induced increase in the sorption surfaces. Analysis by chemical methods overestimated the organic P fraction in the EDTA-NaOH extract in comparison with the determination by ignition procedure. This overestimation was more important in the burned than unburned soil samples, probably due to humification promoted by burning, which increased P sorption by soil particles. The fire-induced changes on the structure of alkali-soluble P were an increase in orthophosphate-P and a decrease in monoester-P and DNA-P. Copyright 2010 Elsevier B.V. All rights reserved.

An overview of a highly versatile forward and stable inverse algorithm for airborne, ground-based and borehole electromagnetic and electric data

NASA Astrophysics Data System (ADS)

Auken, Esben; Christiansen, Anders Vest; Kirkegaard, Casper; Fiandaca, Gianluca; Schamper, Cyril; Behroozmand, Ahmad Ali; Binley, Andrew; Nielsen, Emil; Effersø, Flemming; Christensen, Niels Bøie; Sørensen, Kurt; Foged, Nikolaj; Vignoli, Giulio

2015-07-01

We present an overview of a mature, robust and general algorithm providing a single framework for the inversion of most electromagnetic and electrical data types and instrument geometries. The implementation mainly uses a 1D earth formulation for electromagnetics and magnetic resonance sounding (MRS) responses, while the geoelectric responses are both 1D and 2D and the sheet's response models a 3D conductive sheet in a conductive host with an overburden of varying thickness and resistivity. In all cases, the focus is placed on delivering full system forward modelling across all supported types of data. Our implementation is modular, meaning that the bulk of the algorithm is independent of data type, making it easy to add support for new types. Having implemented forward response routines and file I/O for a given data type provides access to a robust and general inversion engine. This engine includes support for mixed data types, arbitrary model parameter constraints, integration of prior information and calculation of both model parameter sensitivity analysis and depth of investigation. We present a review of our implementation and methodology and show four different examples illustrating the versatility of the algorithm. The first example is a laterally constrained joint inversion (LCI) of surface time domain induced polarisation (TDIP) data and borehole TDIP data. The second example shows a spatially constrained inversion (SCI) of airborne transient electromagnetic (AEM) data. The third example is an inversion and sensitivity analysis of MRS data, where the electrical structure is constrained with AEM data. The fourth example is an inversion of AEM data, where the model is described by a 3D sheet in a layered conductive host.

Developing a Research Agenda to Optimize Diagnostic Imaging in the Emergency Department: An Executive Summary of the 2015 Academic Emergency Medicine Consensus Conference.

PubMed

Marin, Jennifer R; Mills, Angela M

2015-12-01

The 2015 Academic Emergency Medicine (AEM) consensus conference, "Diagnostic Imaging in the Emergency Department: A Research Agenda to Optimize Utilization," was held on May 12, 2015, with the goal of developing a high-priority research agenda on which to base future research. The specific aims of the conference were to: 1) understand the current state of evidence regarding emergency department (ED) diagnostic imaging utilization and identify key opportunities, limitations, and gaps in knowledge; 2) develop a consensus-driven research agenda emphasizing priorities and opportunities for research in ED diagnostic imaging; and 3) explore specific funding mechanisms available to facilitate research in ED diagnostic imaging. Over a 2-year period, the executive committee and other experts in the field convened regularly to identify specific areas in need of future research. Six content areas within emergency diagnostic imaging were identified prior to the conference and served as the breakout groups on which consensus was achieved: clinical decision rules; use of administrative data; patient-centered outcomes research; training, education, and competency; knowledge translation and barriers to imaging optimization; and comparative effectiveness research in alternatives to traditional computed tomography use. The executive committee invited key stakeholders to assist with planning and to participate in the consensus conference to generate a multidisciplinary agenda. There were 164 individuals involved in the conference spanning various specialties, including emergency medicine (EM), radiology, surgery, medical physics, and the decision sciences. This issue of AEM is dedicated to the proceedings of the 16th annual AEM consensus conference as well as original research related to emergency diagnostic imaging. © 2015 by the Society for Academic Emergency Medicine.

Spaceflight Effects on Mammalian Development Summary of Research

NASA Technical Reports Server (NTRS)

Alberts, Jeffrey

1998-01-01

Pregnant rats were flown as small payloads on the Space Shuttle and studied during the flight and for approximately a week after returning to Earth, when they were due to deliver their offspring. Studies of vestibular function in the rat pups were examined as part of the research program. Daily videorecordings were made of the rats' behavior in the Animal Enclosure Modules (AEMS) and in identical compartments maintained in the Orbiter Environment Simulator at the Kennedy Space Center (referred to below as Synchronous Control groups). There was continuous postflight surveillance of the rat dams, including timelapse recordings of labor and delivery. The videorecords provided by crewmembers constitute the best systematic views of spaceflown rats to date, despite the dramatic deterioration of visibility sustained after about the 4th day of flight. We were able to make both qualitative and quantitative observations. Rats were observed to engage in a varied repertoire of species-typical activities within the confines of the AEM. We devised a kinematic coding scheme by which we classified and quantified the movements made by dams in space and in the 1-g control condition. We found that movements involving pitch and yaw were about equivalent in Flight and Synchronous animals. In contrast, Flight dams displayed about seven times more rolling movements than did Control. NASA enabled early access to the AEMs after the Shuttle landed. Rats were intact and healthy. Body weight gain during the 9-11 day flights was equivalent to Controls. Post-flight observations, derived from 24hr/day videorecordings, showed that Flight rats ambulated less, reared fewer times and spent less time bipedal than did controls. Overall, their anti-gravitational responses appeared compromised.

Spaceflight effects on T lymphocyte distribution, function and gene expression

PubMed Central

Gridley, Daila S.; Slater, James M.; Luo-Owen, Xian; Rizvi, Asma; Chapes, Stephen K.; Stodieck, Louis S.; Ferguson, Virginia L.; Pecaut, Michael J.

2009-01-01

The immune system is highly sensitive to stressors present during spaceflight. The major emphasis of this study was on the T lymphocytes in C57BL/6NTac mice after return from a 13-day space shuttle mission (STS-118). Spleens and thymuses from flight animals (FLT) and ground controls similarly housed in animal enclosure modules (AEM) were evaluated within 3–6 h after landing. Phytohemagglutinin-induced splenocyte DNA synthesis was significantly reduced in FLT mice when based on both counts per minute and stimulation indexes (P < 0.05). Flow cytometry showed that CD3+ T and CD19+ B cell counts were low in spleens from the FLT group, whereas the number of NK1.1+ natural killer (NK) cells was increased (P < 0.01 for all three populations vs. AEM). The numerical changes resulted in a low percentage of T cells and high percentage of NK cells in FLT animals (P < 0.05). After activation of spleen cells with anti-CD3 monoclonal antibody, interleukin-2 (IL-2) was decreased, but IL-10, interferon-γ, and macrophage inflammatory protein-1α were increased in FLT mice (P < 0.05). Analysis of cancer-related genes in the thymus showed that the expression of 30 of 84 genes was significantly affected by flight (P < 0.05). Genes that differed from AEM controls by at least 1.5-fold were Birc5, Figf, Grb2, and Tert (upregulated) and Fos, Ifnb1, Itgb3, Mmp9, Myc, Pdgfb, S100a4, Thbs, and Tnf (downregulated). Collectively, the data show that T cell distribution, function, and gene expression are significantly modified shortly after return from the spaceflight environment. PMID:18988762

DEMONSTRATION OF THE ANALYTIC ELEMENT METHOD FOR WELLHEAD PROTECTION

EPA Science Inventory

A new computer program has been developed to determine time-of-travel capture zones in relatively simple geohydrological settings. The WhAEM package contains an analytic element model that uses superposition of (many) closed form analytical solutions to generate a ground-water fl...

WELLHEAD ANALYTIC ELEMENT MODEL FOR WINDOWS

EPA Science Inventory

WhAEM2000 (wellhead analytic element model for Win 98/00/NT/XP) is a public domain, ground-water flow model designed to facilitate capture zone delineation and protection area mapping in support of the State's and Tribe's Wellhead Protection Programs (WHPP) and Source Water Asses...

What is the actual cost of providing the intrauterine system for contraception in a UK community sexual and reproductive health setting?

PubMed

Cook, Louise; Fleming, Charlotte

2014-01-01

The anticipated increase in uptake of intrauterine system (IUS) fittings is slower than predicted by the National Institute for Health and Clinical Excellence (NICE). There is evidence to suggest that this is because of a high perceived cost of providing this contraceptive method. Whereas studies to date have all guessed at these costs, we calculated the actual costs of providing the IUS. We tracked the notes of 283 women who had an IUS fitted in our community sexual and reproductive health service for 5 years. We recorded duration of use, measured the actual cost of all appointments and interventions over the lifespan of the device, and compared our findings with NICE predicted costs. With 70% complete follow-up, the average duration of use of the IUS was 3.44 years compared to NICE's prediction of 3.32. The average annual cost of providing an IUS for contraception in community clinics was £54.55 per woman; this compares with £70.49 modelled by NICE for provision in primary care. Most (80%) of the cost is incurred in the first year. The cost of managing problems is small. Providing the IUS for contraception was 23% cheaper in the present study than that predicted by NICE and cheaper than providing combined oral contraception in our service. Fitting IUSs in community clinics may be cheaper than in primary care. Streamlining the patient pathway will reduce costs further. Restricting access to the IUS because of initial cost is a false economy.

SMART lunch box intervention to improve the food and nutrient content of children's packed lunches: UK wide cluster randomised controlled trial.

PubMed

Evans, C E L; Greenwood, D C; Thomas, J D; Cleghorn, C L; Kitchen, M S; Cade, J E

2010-11-01

Government standards are now in place for children's school meals but not for lunches prepared at home. The aim of this trial is to improve the content of children's packed lunches. A cluster randomised controlled trial in 89 primary schools across the UK involving 1291 children, age 8-9 years at baseline. Follow-up was 12 months after baseline. A "SMART" lunch box intervention programme consisted of food boxes, bag and supporting materials. The main outcome measures were weights of foods and proportion of children provided with sandwiches, fruit, vegetables, dairy food, savoury snacks and confectionery in each packed lunch. Levels of nutrients provided including energy, total fat, saturated fat, protein, non-milk extrinsic sugar, sodium, calcium, iron, folate, zinc, vitamin A and vitamin C. Moderately higher weights of fruit, vegetables, dairy and starchy food and lower weights of savoury snacks were provided to children in the intervention group. Children in the intervention group were provided with slightly higher levels of vitamin A and folate. 11% more children were provided with vegetables/salad in their packed lunch, and 13% fewer children were provided with savoury snacks (crisps). Children in the intervention group were more likely to be provided with packed lunches meeting the government school meal standards. The SMART lunch box intervention, targeting parents and children, led to small improvements in the food and nutrient content of children's packed lunches. Further interventions are required to bring packed lunches in line with the new government standards for school meals. Current controlled trials ISRCTN77710993.

Hypereosinophilia and acute bilateral facial palsy: an unusual presentation of a common disease.

PubMed

Webb, Alastair John Stewart; Conlon, Chris; Briley, Dennis

2012-10-01

A 60-year-old man presented with an acute, pruritic, erythematous rash associated with marked hypereosinophilia (2.34×10(9)/l (0.04-0.40)). There was eosinophilic infiltration on hepatic, bone marrow and lymph node biopsies, with multiple lung nodules and mild splenomegaly. However, extensive investigation excluded parasitic or bacterial causes, specific allergens or the Fip1L1 mutation seen in myeloproliferative hypereosinophilia. Six months into the illness, he developed an acute, left, complete lower motor neurone facial palsy over hours, and an acute right lower motor neurone facial palsy 2 weeks later, without recovery. Over the subsequent 3 months, he developed complex partial seizures, a transient 72-h non-epileptic encephalopathy and episodic vertigo with ataxia. Further investigation showed bilateral enhancement of the VII nerves and labyrinthis on gadolinium-enhanced MR brain scan, cerebrospinal fluid lymphocytosis and neurophysiological evidence of polyradicolopathy. His eosinophil count fell with corticosteroids, hydroxycarbamide, imatinib and ultimately mepolezumab, but without symptomatic improvement. Repeat lymph node biopsy showed Kaposi's sarcoma, leading to a diagnosis of HIV-1 infection with a modestly reduced CD4 count of 413×10(6)/l (430-1690). Hypereosinophila and eosinophilic folliculitis are recognised features of advanced HIV infection, and transient bilateral facial palsy occasionally occurs at the time of seroconversion. This is the first report of a chronic bilateral facial palsy likely due to primary HIV infection, not occurring during seroconversion and in association with hypereosinophilia. This case emphasises the protean manifestations of HIV infection and the need for routine testing in atypical clinical presentations.

Report to Congress on the U.S. Department of Energy`s Environmental Management Science Program: Research funded and its linkages to environmental cleanup problems, and high out-year cost environmental management project descriptions. Volume 3 of 3 -- Appendix C

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-04-01

The Department of Energy`s Environmental Management Science Program (EMSP) serves as a catalyst for the application of scientific discoveries to the development and deployment of technologies that will lead to reduction of the costs and risks associated with cleaning up the nation`s nuclear complex. Appendix C provides details about each of the Department`s 82 high cost projects and lists the EMSP research awards with potential to impact each of these projects. The high cost projects listed are those having costs greater than $50 million in constant 1998 dollars from the year 2007 and beyond, based on the March 1998 Acceleratingmore » Cleanup: Paths to Closure Draft data, and having costs of quantities of material associated with an environmental management problem area. The high cost project information is grouped by operations office and organized by site and project code. Each operations office section begins with a list of research needs associated with that operations office. Potentially related research awards are listed by problem area in the Index of Research Awards by Environmental Management Problem Area, which can be found at the end of appendices B and C. For projects that address high risks to the public, workers, or the environment, refer also the Health/Ecology/Risk problem area awards. Research needs are programmatic or technical challenges that may benefit from knowledge gained through basic research.« less

DEMONSTRATION OF THE ANALYTIC ELEMENT METHOD FOR WELLHEAD PROJECTION - PROJECT SUMMARY

EPA Science Inventory

A new computer program has been developed to determine time-of-travel capture zones in relatively simple geohydrological settings. The WhAEM package contains an analytic element model that uses superposition of (many) closed form analytical solutions to generate a ground-water fl...

ANALYTIC ELEMENT GROUND WATER MODELING AS A RESEARCH PROGRAM (1980-2006)

EPA Science Inventory

Scientists and engineers who use the analytic element method (AEM) for solving problems of regional ground water flow may be considered a community, and this community can be studied from the perspective of history and philosophy of science. Applying the methods of the Hungarian...

2D Automatic body-fitted structured mesh generation using advancing extraction method

USDA-ARS?s Scientific Manuscript database

This paper presents an automatic mesh generation algorithm for body-fitted structured meshes in Computational Fluids Dynamics (CFD) analysis using the Advancing Extraction Method (AEM). The method is applicable to two-dimensional domains with complex geometries, which have the hierarchical tree-like...

2D automatic body-fitted structured mesh generation using advancing extraction method

USDA-ARS?s Scientific Manuscript database

This paper presents an automatic mesh generation algorithm for body-fitted structured meshes in Computational Fluids Dynamics (CFD) analysis using the Advancing Extraction Method (AEM). The method is applicable to two-dimensional domains with complex geometries, which have the hierarchical tree-like...

Using the History of Economic Ideas to Teach Social Studies.

ERIC Educational Resources Information Center

O'Donnel, Margaret G.

1987-01-01

Illustrates how the ideas of classical economists Adam Smith, Thomas Robert Malthus, David Ricardo, and John Stewart Mill are excellent sources for the contemporary social studies teacher. Suggests classroom applications to be used in conjunction with explanation of the economic principles of each of the above-named theorists. (AEM)

What's In a Name? The Argument for Changing the name of IAEMS and Its Affiliated Societies.

EPA Science Inventory

We identify trends over the past decades in membership in societies affiliated with the International Association of Environmental Mutagen Societies (lAEMS), and we also highlight findings in a recent review by Claxton et al, [Environ Health Perspect, in press] regarding the numb...

WHAEM: PROGRAM DOCUMENTATION FOR THE WELLHEAD ANALYTIC ELEMENT MODEL (EPA/600/SR-94/210)

EPA Science Inventory

A new computer program has been developed to determine time-of-travel capture zones in relatively simple geohydrological settings. The WhAEM package contains an analytic element model that uses superposition of (many) closed form analytical solutions to generate a groundwater flo...

ENVIRONMENTAL RESEARCH BRIEF : ANALYTIC ELEMENT MODELING OF GROUND-WATER FLOW AND HIGH PERFORMANCE COMPUTING

EPA Science Inventory

Several advances in the analytic element method have been made to enhance its performance and facilitate three-dimensional ground-water flow modeling in a regional aquifer setting. First, a new public domain modular code (ModAEM) has been developed for modeling ground-water flow ...

Discipline-Based Art Education in Secondary Classrooms.

ERIC Educational Resources Information Center

Day, Michael D.

1987-01-01

Describes two studies of art instruction offered to secondary school students which integrated art production with critical and historical learning and provided some comparisons with non-integrated approaches. Provides observations of high school art programs that included art history and criticism as part of the integrated art curriculum. (AEM)

A Program Aimed toward Inclusive Excellence for Underrepresented Undergraduate Women in the Sciences

ERIC Educational Resources Information Center

Katz, Laura A.; Aloisio, Kathryn M.; Horton, Nicholas J.; Ly, Minh; Pruss, Sara; Queeney, Kate; Rowen, Cate; DiBartolo, Patricia Marten

2017-01-01

Created to foster inclusive excellence, Smith College's Achieving Excellence in Mathematics, Engineering, and Science (AEMES) Scholars program provides early faculty-mentored research opportunities and other programming as a way to foster success in academic outcomes for underrepresented women in science. Using academic record data, we compared…

Complementary Roles of Spark Range and Onboard Free-Flight Measurements for Projectile Development

DTIC Science & Technology

2009-08-01

MET data adequate for aerodynamic analysis requires coordinating with local MET personnel for the release of balloons at strategic times and...TACOM ARDEC AMSRD AAR AEM C M CORZO A READDY R LEE J COSME BLDG 94 PICATINNY ARSENAL NJ 07806-5000 1 COMMANDER US

Agricultural Education Science Activity--Nos. AEM 1-4.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Agricultural Curriculum Materials Service.

This packet contains four science learning activities that can be used in agricultural education courses. The activities cover these topics: (1) determining the effect of air pressure on fluid flow; (2) how lubrication and oil viscosity affect friction; (3) determining relative strengths of wood fasteners; and (4) determining the effects of…

Unleashing Geophysics Data with Modern Formats and Services

NASA Astrophysics Data System (ADS)

Ip, Alex; Brodie, Ross C.; Druken, Kelsey; Bastrakova, Irina; Evans, Ben; Kemp, Carina; Richardson, Murray; Trenham, Claire; Wang, Jingbo; Wyborn, Lesley

2016-04-01

Geoscience Australia (GA) is the national steward of large volumes of geophysical data extending over the entire Australasian region and spanning many decades. The volume and variety of data which must be managed, coupled with the increasing need to support machine-to-machine data access, mean that the old "click-and-ship" model delivering data as downloadable files for local analysis is rapidly becoming unviable - a "big data" problem not unique to geophysics. The Australian Government, through the Research Data Services (RDS) Project, recently funded the Australian National Computational Infrastructure (NCI) to organize a wide range of Earth Systems data from diverse collections including geoscience, geophysics, environment, climate, weather, and water resources onto a single High Performance Data (HPD) Node. This platform, which now contains over 10 petabytes of data, is called the National Environmental Research Data Interoperability Platform (NERDIP), and is designed to facilitate broad user access, maximise reuse, and enable integration. GA has contributed several hundred terabytes of geophysical data to the NERDIP. Historically, geophysical datasets have been stored in a range of formats, with metadata of varying quality and accessibility, and without standardised vocabularies. This has made it extremely difficult to aggregate original data from multiple surveys (particularly un-gridded geophysics point/line data) into standard formats suited to High Performance Computing (HPC) environments. To address this, it was decided to use the NERDIP-preferred Hierarchical Data Format (HDF) 5, which is a proven, standard, open, self-describing and high-performance format supported by extensive software tools, libraries and data services. The Network Common Data Form (NetCDF) 4 API facilitates the use of data in HDF5, whilst the NetCDF Climate & Forecasting conventions (NetCDF-CF) further constrain NetCDF4/HDF5 data so as to provide greater inherent interoperability. The first geophysical data collection selected for transformation by GA was Airborne ElectroMagnetics (AEM) data which was held in proprietary-format files, with associated ISO 19115 metadata held in a separate relational database. Existing NetCDF-CF metadata profiles were enhanced to cover AEM and other geophysical data types, and work is underway to formalise the new geophysics vocabulary as a proposed extension to the Climate & Forecasting conventions. The richness and flexibility of HDF5's internal indexing mechanisms has allowed lossless restructuring of the AEM data for efficient storage, subsetting and access via either the NetCDF4/HDF5 APIs or Open-source Project for a Network Data Access Protocol (OPeNDAP) data services. This approach not only supports large-scale HPC processing, but also interactive access to a wide range of geophysical data in user-friendly environments such as iPython notebooks and more sophisticated cloud-enabled portals such as the Virtual Geophysics Laboratory (VGL). As multidimensional AEM datasets are relatively complex compared to other geophysical data types, the general approach employed in this project for modernizing AEM data is likely to be applicable to other geophysics data types. When combined with the use of standards-based data services and APIs, a coordinated, systematic modernisation will result in vastly improved accessibility to, and usability of, geophysical data in a wide range of computational environments both within and beyond the geophysics community.

Determination of cocaine and its derivatives in hair samples by liquid phase microextraction (LPME) and gas chromatography-mass spectrometry (GC-MS).

PubMed

Pego, A M F; Roveri, F L; Kuninari, R Y; Leyton, V; Miziara, I D; Yonamine, M

2017-05-01

Hair testing is a recognized approach when it comes to accessing historical drug use. According to the World Drug Report of United Nations Office on Drugs and Crime (UNODC) 2015, Brazil is the largest cocaine (COC) market in South America. New analytical methodologies to detect crack/cocaine analytes in hair samples are highly desirable. Here, a method consisting of a liquid-phase microextraction (LPME) as a clean-up step, followed by gas chromatography-mass spectrometry (GC-MS) analysis has been proposed. The new validated method consisted of a washing step; an overnight incubation with methanol and a quick derivatization with butylchloroformate. Once derivatized, the samples were then submitted to the LPME procedure. Limits of detection (LoD) and quantitation (LoQ) obtained were of 0.1 and 0.5ng/mg for COC 0.4 and 0.5ng/mg for anhydroecgonine methyl ester (AEME); 0.03 and 0.05 for cocaethylene (CE), respectively and 0.05ng/mg for both LoD and LoQ for benzoylecgonine (BZE). All calibration curves were linear over the scope applied, from LoQ up to 20ng/mg, with a r 2 >0.99. Precision and accuracy assays showed acceptable %RSD values, according to international guidelines. Twelve postmortem head hair samples stemming from the Institute of Legal Medicine of Sao Paulo (IML-SP) have been analyzed, from which seven have shown to be positive for COC (0.75->20ng/mg) and BZE (0.1->20ng/mg). Apart from COC's main metabolite, four samples were also positive for CE (0.1-3.9ng/mg) and three samples for AEME (0.5-4.9ng/mg). To conclude, the LPME technique together with GC-MS analysis have shown promising results and were able to meet the demand of the laboratory of analyzing postmortem hair samples to look for all four analytes. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Conference on Gender-specific Research in Emergency Care: An Executive Summary

PubMed Central

Safdar, Basmah; Greenberg, Marna Rayl

2015-01-01

With the goal of reducing inequalities in patient care, the 2014 Academic Emergency Medicine (AEM) consensus conference, “Gender-Specific Research in Emergency Care: Investigate, Understand, and Translate How Gender Affects Patient Outcomes,” convened a diverse group of researchers, clinicians, health care providers, patients, and representatives of federal agencies and policy-makers in Dallas, Texas, in May 2014. The executive and steering committees identified seven clinical domains as key to gender-specific emergency care: cardiovascular, neurological, trauma/injury, substance abuse, pain, mental health, and diagnostic imaging. The main aims of the conference were to: 1) summarize and consolidate current data related to sex-and gender-specific research for acute care and identify critical gender-related gaps in knowledge to inform an EM research agenda; 2) create a consensus-driven research agenda that advances sex- and gender-specific research in the prevention, diagnosis, and management of acute diseases and identify strategies to investigate them; and 3) build a multinational interdisciplinary consortium to disseminate and study the sex and gender medicine of acute conditions. Over a 2-year period, this collaborative network of stakeholders identified key areas where sex- and gender-specific research is most likely to improve clinical care and ultimately patient outcomes. The iterative consensus process culminated in a daylong conference on May 13, 2014, with a total of 133 registrants, with the majority being between ages 31 and 50 years (57%), females (71%), and whites (79%). Content experts led the consensus-building workshops at the conference and used the nominal group technique to consolidate consensus recommendations for priority research. In addition, panel sessions addressed funding mechanisms for gender-specific research as well as gender-specific regulatory challenges to product development and approval. This special issue of AEM reports the results of the 2014 consensus conference as well as related original research with the goal of bringing high-quality equitable care to male and female emergency patients. PMID:25420469

Quantitative determination of polysulfide in albumins, plasma proteins and biological fluid samples using a novel combined assays approach.

PubMed

Ikeda, Mayumi; Ishima, Yu; Shibata, Akitomo; Chuang, Victor T G; Sawa, Tomohiro; Ihara, Hideshi; Watanabe, Hiroshi; Xian, Ming; Ouchi, Yuya; Shimizu, Taro; Ando, Hidenori; Ukawa, Masami; Ishida, Tatsuhiro; Akaike, Takaaki; Otagiri, Masaki; Maruyama, Toru

2017-05-29

Hydrogen sulfide (H 2 S) signaling involves polysulfide (RSS n SR') formation on various proteins. However, the current lack of sensitive polysulfide detection assays poses methodological challenges for understanding sulfane sulfur homeostasis and signaling. We developed a novel combined assay by modifying Sulfide Antioxidant Buffer (SAOB) to produce an "Elimination Method of Sulfide from Polysulfide" (EMSP) treatment solution that liberates sulfide, followed with methylene blue (MB) sulfide detection assay. The combined EMSP-MB sulfide detection assay performed on low molecular weight sulfur species showed that sulfide was produced from trisulfide compounds such as glutathione trisulfide and diallyl trisulfide, but not from the thiol compounds such as cysteine, cystine and glutathione. In the case of plasma proteins, this novel combined detection assay revealed that approximately 14.7, 1.7, 3.9, 3.7 sulfide mol/mol released from human serum albumin, α 1 -anti-trypsin, α 1 -acid glycoprotein and ovalbumin, respectively, suggesting that serum albumin is a major pool of polysulfide in human blood circulation. Taken together with the results of albumins of different species, the liberated sulfide has a good correlation with cysteine instead of methionine, indicating the site of incorporation of polysulfide is cysteine. With this novel sulfide detention assay, approximately 8,000, 120 and 1100 μM of polysulfide concentrations was quantitated in human healthy plasma, saliva and tear, respectively. Our promising polysulfide specific detection assay can be a very important tool because quantitative determination of polysulfide sheds light on the functional consequence of protein-bound cysteine polysulfide and expands the research area of reactive oxygen to reactive polysulfide species. Copyright © 2017 Elsevier B.V. All rights reserved.

Antibiotics in urinary-tract infections. Sustained change in prescribing habits by practice test and self-reflection: a mixed methods before-after study.

PubMed

Kuehlein, T; Goetz, K; Laux, G; Gutscher, A; Szecsenyi, J; Joos, S

2011-06-01

BACKGROUND The German guideline recommends trimethoprim (TMP) for the treatment of uncomplicated lower-urinary-tract infections (uLUTI) in primary care. In the authors' research network, the participating general practitioners (GPs) were asked why they prescribe mostly quinolones instead. The GPs stated the perception of a high rate of therapy failure of TMP and strongly rejected the guideline. OBJECTIVE To examine prescribing behaviour for uLUTI and whether a practice test of TMP might effect a change in prescribing habits. METHODS The study was conducted using observational and qualitative elements. A first focus-group (n=6) assessed reasons for current prescribing behaviour. In a 3-month practice test, patients with uLUTI were prescribed TMP (150 mg twice for 3 days). In a second focus group, the GPs (n=12) were presented with the results of the practice test. RESULTS The first focus group revealed that prescribing was mainly driven by former hospital training and what was perceived as common therapy. GPs felt no need to change a successful regimen. In the practice test, TMP had a success rate of 94% (84 episodes of uLUTI). The second focus group revealed that the practice test had strongly changed opinions in favour of TMP. Self-reflection and ownership of data acquisition were seen as major contributions for change in prescribing. After the test period, TMP remained the antibiotic most often prescribed. CONCLUSION Internal evidence and peer-group opinion are strong determinants for clinical decisions. A self-conducted practice test, together with self-reflection in a peer group, strongly supports the process of change.

Mass Balance of Multiyear Sea Ice in the Southern Beaufort Sea

DTIC Science & Technology

2014-09-30

Petty et al. We will extend these results by combining them with satelite -derived ice age data (Maslanik et al., 2007) to focus on the areal...from buoys and satelites with thickness data from AEM surveys, while for the repeat- Figure 1: “Pseudo-plumes” of icepass analysis we are also using

Modelling a real-world buried valley system with vertical non-stationarity using multiple-point statistics

NASA Astrophysics Data System (ADS)

He, Xiulan; Sonnenborg, Torben O.; Jørgensen, Flemming; Jensen, Karsten H.

2017-03-01

Stationarity has traditionally been a requirement of geostatistical simulations. A common way to deal with non-stationarity is to divide the system into stationary sub-regions and subsequently merge the realizations for each region. Recently, the so-called partition approach that has the flexibility to model non-stationary systems directly was developed for multiple-point statistics simulation (MPS). The objective of this study is to apply the MPS partition method with conventional borehole logs and high-resolution airborne electromagnetic (AEM) data, for simulation of a real-world non-stationary geological system characterized by a network of connected buried valleys that incise deeply into layered Miocene sediments (case study in Denmark). The results show that, based on fragmented information of the formation boundaries, the MPS partition method is able to simulate a non-stationary system including valley structures embedded in a layered Miocene sequence in a single run. Besides, statistical information retrieved from the AEM data improved the simulation of the geology significantly, especially for the deep-seated buried valley sediments where borehole information is sparse.

Review of cell performance in anion exchange membrane fuel cells

NASA Astrophysics Data System (ADS)

Dekel, Dario R.

2018-01-01

Anion exchange membrane fuel cells (AEMFCs) have recently received increasing attention since in principle they allow for the use of non-precious metal catalysts, which dramatically reduces the cost per kilowatt of power in fuel cell devices. Until not long ago, the main barrier in the development of AEMFCs was the availability of highly conductive anion exchange membranes (AEMs); however, improvements on this front in the past decade show that newly developed AEMs have already reached high levels of conductivity, leading to satisfactory cell performance. In recent years, a growing number of research studies have reported AEMFC performance results. In the last three years, new records in performance were achieved. Most of the literature reporting cell performance is based on hydrogen-AEMFCs, although an increasing number of studies have also reported the use of fuels others than hydrogen - such as alcohols, non-alcohol C-based fuels, as well as N-based fuels. This article reviews the cell performance and performance stability achieved in AEMFCs through the years since the first reports in the early 2000s.

Silk textile with antimicrobial AEM5772/5 (Dermasilk): a pilot study with positive influence on acne vulgaris on the back.

PubMed

Schaunig, Caroline; Kopera, Daisy

2017-05-01

The use of special silk textiles (Dermasilk) has shown positive effects on chronic inflammatory diseases like lichen sclerosus et atrophicus, atopic dermatitis, diabetic ulcerations, and vulvovaginal candidiasis. Wearing T-shirts of this particular fabric could be useful in the management of patients with acne vulgaris on the back and trunk. Dermasilk T-shirts were given to 14 patients with acne vulgaris papulopustulosa on the back. The patients wore these shirts every night for 6 weeks, and their acne lesions were monitored. Dermasilk represents a polymerisate of fibroin, a silk protein, and antimicrobial AEM5772/5, an unsoluble colorless, odorless ammonium with antifungal and antibacterial ability. Photographic documentation before and after 6 weeks showed a clinically significant reduction in acne lesions on the back without any concomitant treatment or change in lifestyle and living conditions. The use of Dermasilk textiles in other subacute-chronic inflammatory skin diseases has shown positive effects. This is the first report on their safe and effective use in the management of acne vulgaris papulopustulosa corporis. © 2017 The International Society of Dermatology.

Effect of separator and inoculum type on electricity generation and microbial community in single-chamber microbial fuel cells.

PubMed

Yu, Jaecheul; Park, Younghyun; Lee, Taeho

2014-04-01

Single-chamber microbial fuel cell (SMFC)-I consisted of 4 separator-electrode assemblies (SEAs) with two types of cation exchange membrane (CEM: Nafion and CMI 7000) and an anion exchange membrane (AEM: AMI 7001). SMFC-II consisted of 4 SEAs with Nafion and three types of nonwoven fabric. SMFC-I and -II were inoculated with anaerobic digested and activated sludge, respectively, and operated under fed-batch mode. In SMFC I, AEM-SEA showed a maximum power density (PDmax). Nafion-SEA showed a PDmax in SMFC II, which was similar to that of Nafion-SEA of SMFC I. Although different bacteria were developed in SMFC-I (Deltaproteobacteria and Firmicutes) and SMFC-II (Gammaproteobacteria, Betaproteobacteria and Bacteroidetes), the inoculum type little affects electricity generation. Variations of pH and oxygen in biofilm have influenced microbial community structure and electricity generation according to the electrode and separator material. Although the electricity generation of non-woven fabric-SEA was less than that of Nafion-SEA, the use of non-woven fabrics is expected to reduce the construction and operating costs of MFCs.

Photo-Cross-Linked Anion Exchange Membranes with Improved Water Management and Conductivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ertem, S. Piril; Tsai, Tsung-Han; Donahue, Melissa M.

Robust, cross-linked anion exchange membranes (AEMs) were prepared from solvent-processable polyisoprene- ran -poly(vinylbenzyltrimethylammonium chloride) (PI- ran -P- [VBTMA][Cl]) ionomers via photoinitiated thiol - ene chem- istry. Two series of membranes were prepared choosing two dithiol cross-linkers, 1,10-decanedithiol and 2,2 ' - (ethylenedioxy)diethanethiol, selected for their di ff erent hydro- phobicities. A strong correlation was found between the choice of dithiol cross-linker, water uptake, morphology, and the ion conductivity of the membranes. Results were compared with previous fi ndings of thermally cross-linked AEMs from analogous random copolymers. Comparably high chloride ion conductivities were obtained at low to moderate ion exchange capacitiesmore » (IECs) with signi fi cantly low water uptake values. It was shown that by choosing a hydrophilic cross-linker ion cluster formation may be suppressed and ion conduction improved. This study highlights that it is possible to promote ion conductivities for low IEC membranes (<1 mmol/g) by forming well- connected, ion conducting network morphology. This observation paves the way for mechanically robust ion conducting membranes with enhanced conductivities and better water management.« less

NASA Applied Sciences Disasters Program Support for the September 2017 Mexico Earthquakes

NASA Astrophysics Data System (ADS)

Glasscoe, M. T.; Kirschbaum, D.; Torres-Perez, J. L.; Yun, S. H.; Owen, S. E.; Hua, H.; Fielding, E. J.; Liang, C.; Bekaert, D. P.; Osmanoglu, B.; Amini, R.; Green, D. S.; Murray, J. J.; Stough, T.; Struve, J. C.; Seepersad, J.; Thompson, V.

2017-12-01

The 8 September M 8.1 Tehuantepec and 19 September M 7.1 Puebla earthquakes were among the largest earthquakes recorded in Mexico. These two events caused widespread damage, affecting several million people and causing numerous casualties. A team of event coordinators in the NASA Applied Sciences Program activated soon after these devastating earthquakes in order to support decision makers in Mexico, using NASA modeling and international remote sensing capabilities to generate decision support products to aid in response and recovery. The NASA Disasters Program promotes the use of Earth observations to improve the prediction of, preparation for, response to, and recovery from natural and technological disasters. For these two events, the Disasters Program worked with Mexico's space agency (Agencia Espacial Mexico, AEM) and the National Center for Prevention of Disasters (Centro Nacional de Prevención de Desastres, CENAPRED) to generate products to support response, decision-making, and recovery. Products were also provided to academic partners, technical institutions, and field responders to support response. In addition, the Program partnered with the US Geological Survey (USGS), Office of Foreign Disaster Assistance (OFDA), and other partners in order to provide information to federal and domestic agencies that were supporting event response. Leveraging the expertise of investigators at NASA Centers, products such as landslide susceptibility maps, precipitation models, and radar based damage assessments and surface deformation maps were generated and used by AEM, CENAPRED, and others during the event. These were used by AEM in collaboration with other government agencies in Mexico to make appropriate decisions for mapping damage, rescue and recovery, and informing the population regarding areas prone to potential risk. We will provide an overview of the response activities and data products generated in support of the earthquake response, partnerships with domestic and international partners, and preliminary feedback from end-user partners in Mexico during response efforts following these two earthquakes.

Effects and Responses to Spaceflight in the Mouse Retina

NASA Technical Reports Server (NTRS)

Zanello, Susana B.; Theriot, Corey; Westby, Christian; Boyle, Richard

2011-01-01

Several stress environmental factors are combined in a unique fashion during spaceflight, affecting living beings widely across their physiological systems. Recently, attention has been placed on vision changes in astronauts returning from long duration missions. Alterations include hyperoptic shift, globe flattening, choroidal folds and optic disc edema, which are probably associated with increased intracranial pressure. These observations justify a better characterization of the ocular health risks associated with spaceflight. This study investigates the impact of spaceflight on the biology of the mouse retina. Within a successful tissue sharing effort, eyes from albino Balb/cJ mice aboard STS-133 were collected for histological analysis and gene expression profiling of the retina at 1 and 7 days after landing. Both vivarium and AEM (Animal Enclosure Module) mice were used as ground controls. Oxidative stress-induced DNA damage was higher in the flight samples compared to controls on R+1, and decreased on R+7. A trend toward higher oxidative and cellular stress response gene expression was also observed on R+1 compared to AEM controls, and these levels decreased on R+7. Several genes coding for key antioxidant enzymes, namely, heme-oxygenase-1, peroxiredoxin, and catalase, were among those upregulated after flight. Likewise, NF B and TGFbeta1, were upregulated in one flight specimen that overall showed the most elevated oxidative stress markers on R+1. In addition, retinas from vivarium control mice evidenced higher oxidative stress markers, NF B and TGFbeta1, likely due to the more intense illumination in vivarium cages versus the AEM. These preliminary data suggest that spaceflight represents a source of environmental stress that translates into oxidative and cellular stress in the retina, which is partially reversible upon return to Earth. Further work is needed to dissect the contribution of the various spaceflight factors (microgravity, radiation) and to evaluate the impact of the stress response on retinal health.

Changes in mouse thymus and spleen after return from the STS-135 mission in space.

PubMed

Gridley, Daila S; Mao, Xiao Wen; Stodieck, Louis S; Ferguson, Virginia L; Bateman, Ted A; Moldovan, Maria; Cunningham, Christopher E; Jones, Tamako A; Slater, Jerry M; Pecaut, Michael J

2013-01-01

Our previous results with flight (FLT) mice showed abnormalities in thymuses and spleens that have potential to compromise immune defense mechanisms. In this study, the organs were further evaluated in C57BL/6 mice after Space Shuttle Atlantis returned from a 13-day mission. Thymuses and spleens were harvested from FLT mice and ground controls housed in similar animal enclosure modules (AEM). Organ and body mass, DNA fragmentation and expression of genes related to T cells and cancer were determined. Although significance was not obtained for thymus mass, DNA fragmentation was greater in the FLT group (P<0.01). Spleen mass alone and relative to body mass was significantly decreased in FLT mice (P<0.05). In FLT thymuses, 6/84 T cell-related genes were affected versus the AEM control group (P<0.05; up: IL10, Il18bp, Il18r1, Spp1; down: Ccl7, IL6); 15/84 cancer-related genes had altered expression (P<0.05; up: Casp8, FGFR2, Figf, Hgf, IGF1, Itga4, Ncam1, Pdgfa, Pik3r1, Serpinb2, Sykb; down: Cdc25a, E2F1, Mmp9, Myc). In the spleen, 8/84 cancer-related genes were affected in FLT mice compared to AEM controls (P<0.05; up: Cdkn2a; down: Birc5, Casp8, Ctnnb1, Map2k1, Mdm2, NFkB1, Pdgfa). Pathway analysis (apoptosis signaling and checkpoint regulation) was used to map relationships among the cancer-related genes. The results showed that a relatively short mission in space had a significant impact on both organs. The findings also indicate that immune system aberrations due to stressors associated with space travel should be included when estimating risk for pathologies such as cancer and infection and in designing appropriate countermeasures. Although this was the historic last flight of NASA's Space Shuttle Program, exploration of space will undoubtedly continue.

High-Performance X-ray Detection in a New Analytical Electron Microscope

NASA Technical Reports Server (NTRS)

Lyman, C. E.; Goldstein, J. I.; Williams, D. B.; Ackland, D. W.; vonHarrach, S.; Nicholls, A. W.; Statham, P. J.

1994-01-01

X-ray detection by energy-dispersive spectrometry in the analytical electron microscope (AEM) is often limited by low collected X-ray intensity (P), modest peak-to-background (P/B) ratios, and limitations on total counting time (tau) due to specimen drift and contamination. A new AFM has been designed with maximization of P. P/B, and tau as the primary considerations. Maximization of P has been accomplished by employing a field-emission electron gun, X-ray detectors with high collection angles, high-speed beam blanking to allow only one photon into the detector at a time, and simultaneous collection from two detectors. P/B has been maximized by reducing extraneous background signals generated at the specimen holder, the polepieces and the detector collimator. The maximum practical tau has been increased by reducing specimen contamination and employing electronic drift correction. Performance improvments have been measured using the NIST standard Cr thin film. The 0-3 steradian solid angle of X-ray collection is the highest value available. The beam blanking scheme for X-ray detection provides 3-4 times greater throughput of X-rays at high count rates into a recorded spectrum than normal systems employing pulse-pileup rejection circuits. Simultaneous X-ray collection from two detectors allows the highest X-ray intensity yet recorded to be collected from the NIST Cr thin film. The measured P/B of 6300 is the highest level recorded for an AEM. In addition to collected X-ray intensity (cps/nA) and P/B measured on the standard Cr film, the product of these can be used as a figure-of-merit to evaluate instruments. Estimated minimum mass fraction (MMF) for Cr measured on the standard NIST Cr thin film is also proposed as a figure-of-merit for comparing X-ray detection in AEMs. Determinations here of the MMF of Cr detectable show at least a threefold improvement over previous instruments.

Changes in Mouse Thymus and Spleen after Return from the STS-135 Mission in Space

PubMed Central

Gridley, Daila S.; Mao, Xiao Wen; Stodieck, Louis S.; Ferguson, Virginia L.; Bateman, Ted A.; Moldovan, Maria; Cunningham, Christopher E.; Jones, Tamako A.; Slater, Jerry M.; Pecaut, Michael J.

2013-01-01

Our previous results with flight (FLT) mice showed abnormalities in thymuses and spleens that have potential to compromise immune defense mechanisms. In this study, the organs were further evaluated in C57BL/6 mice after Space Shuttle Atlantis returned from a 13-day mission. Thymuses and spleens were harvested from FLT mice and ground controls housed in similar animal enclosure modules (AEM). Organ and body mass, DNA fragmentation and expression of genes related to T cells and cancer were determined. Although significance was not obtained for thymus mass, DNA fragmentation was greater in the FLT group (P<0.01). Spleen mass alone and relative to body mass was significantly decreased in FLT mice (P<0.05). In FLT thymuses, 6/84 T cell-related genes were affected versus the AEM control group (P<0.05; up: IL10, Il18bp, Il18r1, Spp1; down: Ccl7, IL6); 15/84 cancer-related genes had altered expression (P<0.05; up: Casp8, FGFR2, Figf, Hgf, IGF1, Itga4, Ncam1, Pdgfa, Pik3r1, Serpinb2, Sykb; down: Cdc25a, E2F1, Mmp9, Myc). In the spleen, 8/84 cancer-related genes were affected in FLT mice compared to AEM controls (P<0.05; up: Cdkn2a; down: Birc5, Casp8, Ctnnb1, Map2k1, Mdm2, NFkB1, Pdgfa). Pathway analysis (apoptosis signaling and checkpoint regulation) was used to map relationships among the cancer–related genes. The results showed that a relatively short mission in space had a significant impact on both organs. The findings also indicate that immune system aberrations due to stressors associated with space travel should be included when estimating risk for pathologies such as cancer and infection and in designing appropriate countermeasures. Although this was the historic last flight of NASA’s Space Shuttle Program, exploration of space will undoubtedly continue. PMID:24069384

Using Airborne Geophysics to Improve the Management of Produced Water from Coal Bed Natural Gas Extraction in the Powder River Basin

NASA Astrophysics Data System (ADS)

Sams, J.; Lipinski, B.; Hammack, R.; Veloski, G.; Ackman, T.; Harbert, B.

2005-05-01

The Powder River Basin (PRB) of Wyoming and Montana has seen a boom in drilling for coalbed natural gas (CBNG), the natural gas contained in coal seams. Large quantities of water are coproduced during the extraction process. The water is currently managed by land application (irrigation), returned to shallow groundwater aquifers via infiltration basins, directly discharged to ephemeral or perennial streams, or injected into the deep subsurface via injection wells. At present, there are over 28,000 CBNG wells permitted or drilled in the PRB and it is estimated that another 50,000 to 100,000 new wells will be drilled in the future. Produced water management is a major challenge to the oil and gas industry as well as federal and state regulators. The purpose of this study was to evaluate the use of airborne electromagnetic (AEM) methods for the large-scale mapping of vadose zone properties. The base maps derived from the AEM data show the location of conductive anomalies within the vadose zone. These conductive anomalies have been identified as conditions related to soil properties, geologic features, saturated areas, and seepage zones. In the PRB, the data can be used to identify suitable locations for constructing impoundments in areas that avoid highly conductive soils where infiltrating water may leach salts through the vadose zone and into shallow aquifers. Hydrologic changes within the vadose zone were evaluated by completing an AEM survey in 2003 and 2004 over two coincident spatial areas. The data were analyzed to determine statistical relationships between the data sets, in particular data outliers which may represent areas of significant change between each year. Some outliers plot near areas of CBNG development. Ultimately, it is hoped that the information from these surveys will identify cost effective treatment or disposal options for produced water that address both production and environmental issues.

Decomposing the electromagnetic response of magnetic dipoles to determine the geometric parameters of a dipole conductor

NASA Astrophysics Data System (ADS)

Desmarais, Jacques K.; Smith, Richard S.

2016-03-01

A novel automatic data interpretation algorithm is presented for modelling airborne electromagnetic (AEM) data acquired over resistive environments, using a single-component (vertical) transmitter, where the position and orientation of a dipole conductor is allowed to vary in three dimensions. The algorithm assumes that the magnetic fields produced from compact vortex currents are expressed as a linear combinations of the fields arising from dipoles in the subsurface oriented parallel to the [1, 0, 0], [0, 1, 0], and [0, 0, 1], unit vectors. In this manner, AEM responses can be represented as 12 terms. The relative size of each term in the decomposition can be used to determine geometrical information about the orientation of the subsurface conductivity structure. The geometrical parameters of the dipole (location, depth, dip, strike) are estimated using a combination of a look-up table and a matrix inverted in a least-squares sense. Tests on 703 synthetic models show that the algorithm is capable of extracting most of the correct geometrical parameters of a dipole conductor when three-component receiver data is included in the interpretation procedure. The algorithm is unstable when the target is perfectly horizontal, as the strike is undefined. Ambiguities may occur in predicting the orientation of the dipole conductor if y-component data is excluded from the analysis. Application of our approach to an anomaly on line 15 of the Reid Mahaffy test site yields geometrical parameters in reasonable agreement with previous authors. However, our algorithm provides additional information on the strike and offset from the traverse line of the conductor. Disparities in the values of predicted dip and depth are within the range of numerical precision. The index of fit was better when strike and offset were included in the interpretation procedure. Tests on the data from line 15701 of the Chibougamau MEGATEM survey shows that the algorithm is applicable to situations where three-component AEM data is available.

Voxel inversion of airborne electromagnetic data for improved model integration

NASA Astrophysics Data System (ADS)

Fiandaca, Gianluca; Auken, Esben; Kirkegaard, Casper; Vest Christiansen, Anders

2014-05-01

Inversion of electromagnetic data has migrated from single site interpretations to inversions including entire surveys using spatial constraints to obtain geologically reasonable results. Though, the model space is usually linked to the actual observation points. For airborne electromagnetic (AEM) surveys the spatial discretization of the model space reflects the flight lines. On the contrary, geological and groundwater models most often refer to a regular voxel grid, not correlated to the geophysical model space, and the geophysical information has to be relocated for integration in (hydro)geological models. We have developed a new geophysical inversion algorithm working directly in a voxel grid disconnected from the actual measuring points, which then allows for informing directly geological/hydrogeological models. The new voxel model space defines the soil properties (like resistivity) on a set of nodes, and the distribution of the soil properties is computed everywhere by means of an interpolation function (e.g. inverse distance or kriging). Given this definition of the voxel model space, the 1D forward responses of the AEM data are computed as follows: 1) a 1D model subdivision, in terms of model thicknesses, is defined for each 1D data set, creating "virtual" layers. 2) the "virtual" 1D models at the sounding positions are finalized by interpolating the soil properties (the resistivity) in the center of the "virtual" layers. 3) the forward response is computed in 1D for each "virtual" model. We tested the new inversion scheme on an AEM survey carried out with the SkyTEM system close to Odder, in Denmark. The survey comprises 106054 dual mode AEM soundings, and covers an area of approximately 13 km X 16 km. The voxel inversion was carried out on a structured grid of 260 X 325 X 29 xyz nodes (50 m xy spacing), for a total of 2450500 inversion parameters. A classical spatially constrained inversion (SCI) was carried out on the same data set, using 106054 spatially constrained 1D models with 29 layers. For comparison, the SCI inversion models have been gridded on the same grid of the voxel inversion. The new voxel inversion and the classic SCI give similar data fit and inversion models. The voxel inversion decouples the geophysical model from the position of acquired data, and at the same time fits the data as well as the classic SCI inversion. Compared to the classic approach, the voxel inversion is better suited for informing directly (hydro)geological models and for sequential/Joint/Coupled (hydro)geological inversion. We believe that this new approach will facilitate the integration of geophysics, geology and hydrology for improved groundwater and environmental management.

Web life: The Evil Mad Scientist Project

NASA Astrophysics Data System (ADS)

2009-04-01

What is it? Have you ever tried to electrocute a hot dog? Wondered how to make a robot out of a toothbrush, watch battery and phone-pager motor? Seen a cantaloupe melon and thought, "Hmm, I could make this look like the Death Star from the original Star Wars films"? If you have not, but you would like to - preferably as soon as you can find a pager motor - then this is the site for you. The Evil Mad Scientist Project (EMSP) blog is packed full of ideas for unusual, silly and frequently physics-related creations that bring science out of the laboratory and into kitchens, backyards and tool sheds.

ANALYTIC ELEMENT MODELING FOR SOURCE WATER ASSESSMENTS OF PUBLIC WATER SUPPLY WELLS: CASE STUDIES IN GLACIAL OUTWASH AND BASIN-AND-RANGE

EPA Science Inventory

Over the last 10 years the EPA has invested in analytic elements as a computational method used in public domain software supporting capture zone delineation for source water assessments and wellhead protection. The current release is called WhAEM2000 (wellhead analytic element ...

SOURCE WATER AREA DELINEATION OF PUBLIC WATER SUPPLY WELLS USING WHAEM2000. INTERNATIONAL GROUND WATER MODELING CENTER NEWSLETTER, V.19(1):4

EPA Science Inventory

WhAEM2000 is computer program that solves steady state ground-water flow and advective streamlines in homogeneous, single layer aquifers. The program was designed for capture zone delineation in support of protection of the source water area surrounding public water supply well...

Adoption of Agri-Environmental Measures by Organic Farmers: The Role of Interpersonal Communication

ERIC Educational Resources Information Center

Unay Gailhard, Ilkay; Bavorová, Miroslava; Pirscher, Frauke

2015-01-01

Purpose: The purpose of this study is to investigate the impact of interpersonal communication on the adoption of agri-environmental measures (AEM) by organic farmers in Germany. Methodology: The study used the logit model to predict the probability of adoption behaviour, and Social Network Analysis (SNA) was conducted to analyse the question of…

Understanding Anion Transport in an Aminated Trimethyl Polyphenylene with High Anionic Conductivity

DTIC Science & Technology

2012-01-01

published online DOI: 10.1002/polb.23164 ABSTRACT: An alkaline exchange membrane (AEM) based on an aminated trimethyl poly(phenylene) is studied in...3874–3882. 23 Cotts, R. M.; Hoch, M. J. R.; Sun, T.; Markert , J. T. J. Magn. Reson. (1969) 1989, 83, 252–266. 24 Tanner, J. E. J. Chem. Phys. 1970

Data Analysis of Airborne Electromagnetic Bathymetry.

DTIC Science & Technology

1985-04-01

7 AD-R 58 889 DATA ANALYSIS OF AIRBORNE ELECTROMAGNETIC BRTHYMETRY i/i (U) NAVAL OCEAN RESEARCH AND DEVELOPMENT ACTIVITY NSTL STRTION MS R ZOLLINGER...Naval Ocean Research and Development Activity NSTL, Mississippi 39529 NORDA Report 93 April 1985 AD-A158 809 - Data Analysis of Airborne Electromagnetic ...8217 - Foreword CI Airborne electromagnetic (AEM) systems have traditionally been used for detecting anomalous conductors in the

The Development of Concepts of Handicap in Adolescence: A Cross-Cultural Study. IV. The Rehabilitation of the Handicapped.

ERIC Educational Resources Information Center

Obani, Tim; Doherty, Jim

1987-01-01

Reports study examining the way in which age, sex, nationality, and attitude to the disabled affected the level of understanding achieved by a group of British and Nigerian adolescents about the rehabilitation of disabled individuals. Finds that age is the most important factor, sex somewhat important, and attitude not important. (Author/AEM)

Investigation of electrodialysis anti-fouling configuration for desalting and treating tannery unhairing wastewater: Feasibility of by-products recovery and water recycling.

PubMed

Tamersit, Sabrina; Bouhidel, Kamel-Eddine; Zidani, Zakaria

2018-02-01

The desalination and treatment of tannery unhairing wastewater by electrodialysis (ED) is investigated in this research in order to separate, concentrate, recover and reuse low molecular weight charged species (S 2- , HS - , OH - , Cl - , Ca 2+ , Na + and amino acids), and to separate proteins and recycle treated water. Therefore, a novel electrodialysis membrane configuration was proposed. This was based on a double anti-fouling membrane. The ED anion exchange membrane (AEM), which is very sensitive to organic fouling, was protected by an ultra filtration membrane impermeable to the negatively charged proteins that could not reach the AEM surface. The experimental results were quite promising, and in spite of only one desalination compartment ED cell; the demineralization efficiency was 56 ± 1.25% (5.5-2.4 mS/cm), with a sensitive removal of sulphide, calcium and chloride. The organic matter (protein, peptides…) was isolated in the dilute compartment. The most important result was the total absence of membrane fouling. The experimental results remarkably proved the initial hypothesis, and suggested promising solutions for industrial pollution, where the membrane processes have never been successful. Copyright © 2017 Elsevier Ltd. All rights reserved.

Spaceflight Effects and Molecular Responses in the Mouse Eye: Observations After Shuttle Mission STS-133

NASA Technical Reports Server (NTRS)

Prospero-Ponce, Claudia; Zanello, Susana B.; CoreyTheriot, Patricia; Chevez-Barrios, P.

2012-01-01

Microgravity-induced cephalad fluid shift and radiation exposure are some of the stressors seen in space exploration. Ocular changes leading to visual impairment in astronauts are of occupational health relevance. Therefore, we analyzed the effects of space flight in the eyes of mice. Six mice were assigned to Flight (FLT), Animal enclosure Module (AEM), or vivarium (VIV) group, respectively. Mice were sacrificed at 1, 5 or 7 days after landing from space. One eye was used for histological and immunohistoche-mistry analysis and the other eye for gene expression profiling. 8-OHdG and caspase-3 immunoreactivity were increased in the retina in FLT samples at return(R+1) compared to AEM/VIV groups, and decreased at day 7 (R+7). beta-amyloid was seen in the nerve fibers at the post-laminar region of the optic nerve in the flight samples (R+7). In addition, oxidative and cellular stress response genes were upregulated in the retina of FLT samples upon landing, and decreased by R+7. According to the results, a reversible molecular damage may occur in the retina of mice exposed to spaceflight followed by protective cellular response.

Tackling capacity fading in vanadium flow batteries with amphoteric membranes

NASA Astrophysics Data System (ADS)

Oldenburg, Fabio J.; Schmidt, Thomas J.; Gubler, Lorenz

2017-11-01

Capacity fading and poor electrolyte utilization caused by electrolyte imbalance effects are major drawbacks for the commercialization of vanadium flow batteries (VFB). The influence of membrane type (cationic, anionic, amphoteric) on these effects is studied by determining the excess and net flux of each vanadium ion in an operating VFB assembled with a cation exchange membrane (CEM), Nafion® NR212, an anion exchange membrane (AEM), Fumatech FAP-450, and an amphoteric ion exchange membrane (AIEM) synthesized in-house. It is shown that the net vanadium flux, accompanied by water transport, is directed towards the positive side for the CEM and towards the negative side for the AEM. The content of cation and anion exchange groups in the AIEM is adjusted via radiation grafting to balance the vanadium flux between the two electrolyte sides. With the AIEM the net vanadium flux is significantly reduced and capacity fading due to electrolyte imbalances can be largely eliminated. The membrane's influence on electrolyte imbalance effects is characterized and quantified in one single charge-discharge cycle by analyzing the content of the four different vanadium species in the two electrolytes. The experimental data recorded herewith conclusively explains the electrolyte composition after 80 cycles.

Highly conductive side chain block copolymer anion exchange membranes.

PubMed

Wang, Lizhu; Hickner, Michael A

2016-06-28

Block copolymers based on poly(styrene) having pendent trimethyl styrenylbutyl ammonium (with four carbon ring-ionic group alkyl linkers) or benzyltrimethyl ammonium groups with a methylene bridge between the ring and ionic group were synthesized by reversible addition-fragmentation radical (RAFT) polymerization as anion exchange membranes (AEMs). The C4 side chain polymer showed a 17% increase in Cl(-) conductivity of 33.7 mS cm(-1) compared to the benzyltrimethyl ammonium sample (28.9 mS cm(-1)) under the same conditions (IEC = 3.20 meq. g(-1), hydration number, λ = ∼7.0, cast from DMF/1-propanol (v/v = 3 : 1), relative humidity = 95%). As confirmed by small angle X-ray scattering (SAXS), the side chain block copolymers with tethered ammonium cations showed well-defined lamellar morphologies and a significant reduction in interdomain spacing compared to benzyltrimethyl ammonium containing block copolymers. The chemical stabilities of the block copolymers were evaluated under severe, accelerated conditions, and degradation was observed by (1)H NMR. The block copolymer with C4 side chain trimethyl styrenylbutyl ammonium motifs displayed slightly improved stability compared to that of a benzyltrimethyl ammonium-based AEM at 80 °C in 1 M NaOD aqueous solution for 30 days.

Organization, execution and evaluation of the 2014 Academic Emergency Medicine consensus conference on Gender-Specific Research in Emergency Care - an executive summary.

PubMed

Safdar, Basmah; Greenberg, Marna R

2014-12-01

With the goal of reducing inequalities in patient care, the 2014 Academic Emergency Medicine (AEM) consensus conference, "Gender-Specific Research in Emergency Care: Investigate, Understand, and Translate How Gender Affects Patient Outcomes," convened a diverse group of researchers, clinicians, health care providers, patients, and representatives of federal agencies and policy-makers in Dallas, Texas, in May 2014. The executive and steering committees identified seven clinical domains as key to gender-specific emergency care: cardiovascular, neurological, trauma/injury, substance abuse, pain, mental health, and diagnostic imaging. The main aims of the conference were to: 1) summarize and consolidate current data related to sex- and gender-specific research for acute care and identify critical gender-related gaps in knowledge to inform an EM research agenda; 2) create a consensus-driven research agenda that advances sex- and gender-specific research in the prevention, diagnosis, and management of acute diseases and identify strategies to investigate them; and 3) build a multinational interdisciplinary consortium to disseminate and study the sex and gender medicine of acute conditions. Over a 2-year period, this collaborative network of stakeholders identified key areas where sex- and gender-specific research is most likely to improve clinical care and ultimately patient outcomes. The iterative consensus process culminated in a daylong conference on May 13, 2014, with a total of 133 registrants, with the majority being between ages 31 and 50 years (57%), females (71%), and whites (79%). Content experts led the consensus-building workshops at the conference and used the nominal group technique to consolidate consensus recommendations for priority research. In addition, panel sessions addressed funding mechanisms for gender-specific research as well as gender-specific regulatory challenges to product development and approval. This special issue of AEM reports the results of the 2014 consensus conference as well as related original research with the goal of bringing high-quality equitable care to male and female emergency patients. © 2014 by the Society for Academic Emergency Medicine.

Using FOSM-Based Data Worth Analyses to Design Geophysical Surveys to Reduce Uncertainty in a Regional Groundwater Model Update

NASA Astrophysics Data System (ADS)

Smith, B. D.; White, J.; Kress, W. H.; Clark, B. R.; Barlow, J.

2016-12-01

Hydrogeophysical surveys have become an integral part of understanding hydrogeological frameworks used in groundwater models. Regional models cover a large area where water well data is, at best, scattered and irregular. Since budgets are finite, priorities must be assigned to select optimal areas for geophysical surveys. For airborne electromagnetic (AEM) geophysical surveys, optimization of mapping depth and line spacing needs to take in account the objectives of the groundwater models. The approach discussed here uses a first-order, second-moment (FOSM) uncertainty analyses which assumes an approximate linear relation between model parameters and observations. This assumption allows FOSM analyses to be applied to estimate the value of increased parameter knowledge to reduce forecast uncertainty. FOSM is used to facilitate optimization of yet-to-be-completed geophysical surveying to reduce model forecast uncertainty. The main objective of geophysical surveying is assumed to estimate values and spatial variation in hydrologic parameters (i.e. hydraulic conductivity) as well as map lower permeability layers that influence the spatial distribution of recharge flux. The proposed data worth analysis was applied to Mississippi Embayment Regional Aquifer Study (MERAS) which is being updated. The objective of MERAS is to assess the ground-water availability (status and trends) of the Mississippi embayment aquifer system. The study area covers portions of eight states including Alabama, Arkansas, Illinois, Kentucky, Louisiana, Mississippi, Missouri, and Tennessee. The active model grid covers approximately 70,000 square miles, and incorporates some 6,000 miles of major rivers and over 100,000 water wells. In the FOSM analysis, a dense network of pilot points was used to capture uncertainty in hydraulic conductivity and recharge. To simulate the effect of AEM flight lines, the prior uncertainty for hydraulic conductivity and recharge pilots along potential flight lines was reduced. The FOSM forecast uncertainty estimates were then recalculated and compared to the base forecast uncertainty estimates. The resulting reduction in forecast uncertainty is a measure of the effect on the model from the AEM survey. Iterations through this process, results in optimization of flight line location.

Power generation using different cation, anion, and ultrafiltration membranes in microbial fuel cells.

PubMed

Kim, Jung Rae; Cheng, Shaoan; Oh, Sang-Eun; Logan, Bruce E

2007-02-01

Proton exchange membranes (PEMs) are often used in microbial fuel cells (MFCs) to separate the liquid in the anode and cathode chambers while allowing protons to pass between the chambers. However, negatively or positively charged species present at high concentrations in the medium can also be used to maintain charge balance during power generation. An anion exchange membrane (AEM) produced the largest power density (up to 610 mW/m2) and Coulombic efficiency (72%) in MFCs relative to values achieved with a commonly used PEM (Nafion), a cation exchange membrane (CEM), or three different ultrafiltration (UF) membranes with molecular weight cut offs of 0.5K, 1K, and 3K Daltons in different types of MFCs. The increased performance of the AEM was due to proton charge-transfer facilitated by phosphate anions and low internal resistance. The type of membrane affected maximum power densities in two-chamber, air-cathode cube MFCs (C-MFCs) with low internal resistance (84-91 omega for all membranes except UF-0.5K) but not in two-chamber aqueous-cathode bottle MFCs (B-MFCs) due to their higher internal resistances (1230-1272 omega except UF-0.5K). The UF-0.5K membrane produced very high internal resistances (6009 omega, B-MFC; 1814omega, C-MFC) and was the least permeable to both oxygen (mass transfer coefficient of k(O) = 0.19 x 10(-4) cm/s) and acetate (k(A) = 0.89 x 10(-8) cm/s). Nafion was the most permeable membrane to oxygen (k(O) = 1.3 x 10(-4) cm/s), and the UF-3K membrane was the most permeable to acetate (k(A) = 7.2 x 10(-8) cm/s). Only a small percent of substrate was unaccounted for based on measured Coulombic efficiencies and estimates of biomass production and substrate losses using Nafion, CEM, and AEM membranes (4-8%), while a substantial portion of substrate was lost to unidentified processes for the UF membranes (40-89%). These results show that many types of membranes can be used in two-chambered MFCs, even membranes that transfer negatively charged species.

A novel sputtered Pd mesh architecture as an advanced electrocatalyst for highly efficient hydrogen production

NASA Astrophysics Data System (ADS)

de Lucas-Consuegra, Antonio; de la Osa, Ana R.; Calcerrada, Ana B.; Linares, José J.; Horwat, David

2016-07-01

This study reports the preparation, characterization and testing of a sputtered Pd mesh-like anode as an advanced electrocatalyst for H2 production from alkaline ethanol solutions in an Alkaline Membrane Electrolyzer (AEM). Pd anodic catalyst is prepared by magnetron sputtering technique onto a microfiber carbon paper support. Scanning Electron Microscopy images reveal that the used preparation technique enables to cover the surface of the carbon microfibers exposed to the Pd target, leading to a continuous network that also maintains part of the original carbon paper macroporosity. Such novel anodic architecture (organic binder free) presents an excellent electro-chemical performance, with a maximum current density of 700 mA cm-2 at 1.3 V, and, concomitantly, a large H2 production rate with low energy requirement compared to water electrolysis. Potassium hydroxide emerges as the best electrolyte, whereas temperature exerts the expected promotional effect up to 90 °C. On the other hand, a 1 mol L-1 ethanol solution is enough to guarantee an efficient fuel supply without any mass transfer limitation. The proposed system also demonstrates to remain stable over 150 h of operation along five consecutives cycles, producing highly pure H2 (99.999%) at the cathode and potassium acetate as the main anodic product.

Report to Congress on the U.S. Department of Energy`s Environmental Management Science Program: Research funded and its linkages to environmental cleanup problems, and Environmental Management Science Program research award abstracts. Volume 2 of 3 -- Appendix B

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Department of Energy`s Environmental Management Science Program (EMSP) serves as a catalyst for the application of scientific discoveries to the development and deployment of technologies that will lead to reduction of the costs and risks associated with cleaning up the nation`s nuclear complex. Appendix B provides details about each of the 202 research awards funded by the EMSP. This information may prove useful to researchers who are attempting to address the Department`s environmental management challenges in their work, program managers who are planning, integrating, and prioritizing Environmental Management projects, and stakeholders and regulators who are interested in the Department`smore » environmental challenges. The research award information is organized by the state and institution in which the lead principal investigator is located. In many cases, the lead principal investigator is one of several investigators at a number of different institutions. In these cases, the lead investigator (major collaborator) at each of the additional institutions is listed. Each research award abstract is followed by a list of high cost projects that can potentially be impacted by the research results. High cost projects are Environmental Management projects that have total costs greater than $50 million from the year 2007 and beyond, based on the March 1998 Accelerating Cleanup: Paths to Closure Draft data, and have costs or quantities of material associated with an Environmental Management problem area. High cost projects which must remain active in the year 2007 and beyond to manage high risk are also identified. Descriptions of these potentially related high cost Environmental Management projects can be found in Appendix C. Additional projects in the same problem area as a research award can be located using the Index of High Cost Environmental Management Projects by Problem Area, at the end of Appendices B and C.« less

Thin Robust Anion Exchange Membranes for Fuel Cell Applications

DTIC Science & Technology

2014-01-01

water diffsuion. Here we use a Polyphenylene Oxide dibock polymer co-polymerized with polyvinyl benzyl trimethyl ammonium blocks ( PPO -b-PVBTMA[F...in PPO -b-PVBTMA[F-] AEM under saturated humidity environment ECS Transactions, 64 (3) 1185-1194 (2014) 1191 Conductivity of this membrane was...makes it a promising material for applications in anion exchange membrane fuel cells. Figure 5: Conductivity of PPO -b-PVBTMA[F-] under 95% Relative

The transfer behavior of different ions across anion and cation exchange membranes under vanadium flow battery medium

NASA Astrophysics Data System (ADS)

Sun, Jiawei; Li, Xianfeng; Xi, Xiaoli; Lai, Qinzhi; Liu, Tao; Zhang, Huamin

2014-12-01

The transfer behavior of different ions (V2+, V3+, VO2+, VO2+, H+, SO42-) across ion exchange membranes is investigated under vanadium flow battery (VFB) operating condition. VX-20 anion exchange membrane (AEM) and Nafion 115 cation exchange membrane (CEM) are selected to investigate the influence of fixed charged groups on the transfer behavior of different ions. The interaction between different ions and water is discussed in detail aiming to ascertain the variation of different ions in the charge-discharge process. Under the VFB medium, the transfer behavior and function of different ions are very different for the AEM and CEM. V2+ ions at the negative side accumulate when VFB is assembled with Nafion 115, while the VO2+ ions at the positive side accumulate for VX-20. The SO42- ions will transfer across Nafion 115 to balance the charges and the protons can balance the charges of VX-20. Finally the capacity fade mechanism of different membranes is investigated, showing that the capacity decay of VFB assembled with Nafion 115 mainly results from the cross mix of vanadium ions across the membrane, however, for VX-20, the side reactions can be the major reason. This paper provides important information about electrolyte for the application of VFB.

Water permeation through anion exchange membranes

NASA Astrophysics Data System (ADS)

Luo, Xiaoyan; Wright, Andrew; Weissbach, Thomas; Holdcroft, Steven

2018-01-01

An understanding of water permeation through solid polymer electrolyte (SPE) membranes is crucial to offset the unbalanced water activity within SPE fuel cells. We examine water permeation through an emerging class of anion exchange membranes, hexamethyl-p-terphenyl poly (dimethylbenzimidazolium) (HMT-PMBI), and compare it against series of membrane thickness for a commercial anion exchange membrane (AEM), Fumapem® FAA-3, and a series of proton exchange membranes, Nafion®. The HMT-PMBI membrane is found to possess higher water permeabilities than Fumapem® FAA-3 and comparable permeability than Nafion (H+). By measuring water permeation through membranes of different thicknesses, we are able to decouple, for the first time, internal and interfacial water permeation resistances through anion exchange membranes. Permeation resistances on liquid/membrane interface is found to be negligible compared to that for vapor/membrane for both series of AEMs. Correspondingly, the resistance of liquid water permeation is found to be one order of magnitude smaller compared to that of vapor water permeation. HMT-PMBI possesses larger effective internal water permeation coefficient than both Fumapem® FAA-3 and Nafion® membranes (60 and 18% larger, respectively). In contrast, the effective interfacial permeation coefficient of HMT-PMBI is found to be similar to Fumapem® (±5%) but smaller than Nafion®(H+) (by 14%).

Application of the finite-field coupled-cluster method to calculate molecular properties relevant to electron electric-dipole-moment searches

NASA Astrophysics Data System (ADS)

Abe, M.; Prasannaa, V. S.; Das, B. P.

2018-03-01

Heavy polar diatomic molecules are currently among the most promising probes of fundamental physics. Constraining the electric dipole moment of the electron (e EDM ), in order to explore physics beyond the standard model, requires a synergy of molecular experiment and theory. Recent advances in experiment in this field have motivated us to implement a finite-field coupled-cluster (FFCC) approach. This work has distinct advantages over the theoretical methods that we had used earlier in the analysis of e EDM searches. We used relativistic FFCC to calculate molecular properties of interest to e EDM experiments, that is, the effective electric field (Eeff) and the permanent electric dipole moment (PDM). We theoretically determine these quantities for the alkaline-earth monofluorides (AEMs), the mercury monohalides (Hg X ), and PbF. The latter two systems, as well as BaF from the AEMs, are of interest to e EDM searches. We also report the calculation of the properties using a relativistic finite-field coupled-cluster approach with single, double, and partial triples' excitations, which is considered to be the gold standard of electronic structure calculations. We also present a detailed error estimate, including errors that stem from our choice of basis sets, and higher-order correlation effects.

National Institutes of Health, Rodent 4 (NIH.R4); Calcium Metabolism and Vascular Function After Spaceflight: A Collaborative Series with NASA and NIH

NASA Technical Reports Server (NTRS)

Reiss-Bubenheim, Debra; Steele, Marianne; Aquillina, Rudy; Savage, Paul D. (Technical Monitor)

1997-01-01

The NIH.R4 payload was a collaborative experiment conducted by NASA's Ames Research Center in conjunction with the National Institutes of Health (NIH). This middeck payload was the fourth in a series of experiments focusing on developmental biology and the effects of microgravity on mammalian systems. The NIH.R4 payload was flown onboard STS-80, which launched November 19, 1996, and landed at Kennedy Space Center on December 7, 1996, and was the longest shuttle mission to date. Fourteen male Spontaneously Hypertensive rats (SHR) were flown; seven in each of two Animal Enclosure Modules (AEM) in the shuttle middeck. The flight animals were exposed to 18 days of microgravity. Two synchronous control groups were utilized for this study in addition to an asynchronous post-flight AEM control study conducted at the PI lab. The animals were fed two different calcium diets in the NASA food bar (2.0% and 0.2%) three weeks prior to launch and insight. Blood pressures were taken at pre-determined intervals and were the basis for flight selection. Upon recovery Dwight animals blood pressure was measured and a variety of tissues were collected. Project testing and data will be presented.

Analyzing a suitable elastic geomechanical model for Vaca Muerta Formation

NASA Astrophysics Data System (ADS)

Sosa Massaro, Agustin; Espinoza, D. Nicolas; Frydman, Marcelo; Barredo, Silvia; Cuervo, Sergio

2017-11-01

Accurate geomechanical evaluation of oil and gas reservoir rocks is important to provide design parameters for drilling, completion and predict production rates. In particular, shale reservoir rocks are geologically complex and heterogeneous. Wells need to be hydraulically fractured for stimulation and, in complex tectonic environments, it is to consider that rock fabric and in situ stress, strongly influence fracture propagation geometry. This article presents a combined wellbore-laboratory characterization of the geomechanical properties of a well in El Trapial/Curamched Field, over the Vaca Muerta Formation, located in the Neuquén Basin in Argentina. The study shows the results of triaxial tests with acoustic measurements in rock plugs from outcrops and field cores, and corresponding dynamic to static correlations considering various elastic models. The models, with increasing complexity, include the Isotropic Elastic Model (IEM), the Anisotropic Elastic Model (AEM) and the Detailed Anisotropic Elastic Model (DAEM). Each model shows advantages over the others. An IEM offers a quick overview, being easy to run without much detailed data for heterogeneous and anisotropic rocks. The DAEM requires significant amounts of data, time and a multidisciplinary team to arrive to a detailed model. Finally, an AEM suits well to an anisotropic and realistic rock without the need of massive amounts of data.

Smart Interpretation - Application of Machine Learning in Geological Interpretation of AEM Data

NASA Astrophysics Data System (ADS)

Bach, T.; Gulbrandsen, M. L.; Jacobsen, R.; Pallesen, T. M.; Jørgensen, F.; Høyer, A. S.; Hansen, T. M.

2015-12-01

When using airborne geophysical measurements in e.g. groundwater mapping, an overwhelming amount of data is collected. Increasingly larger survey areas, denser data collection and limited resources, combines to an increasing problem of building geological models that use all the available data in a manner that is consistent with the geologists knowledge about the geology of the survey area. In the ERGO project, funded by The Danish National Advanced Technology Foundation, we address this problem, by developing new, usable tools, enabling the geologist utilize her geological knowledge directly in the interpretation of the AEM data, and thereby handle the large amount of data, In the project we have developed the mathematical basis for capturing geological expertise in a statistical model. Based on this, we have implemented new algorithms that have been operationalized and embedded in user friendly software. In this software, the machine learning algorithm, Smart Interpretation, enables the geologist to use the system as an assistant in the geological modelling process. As the software 'learns' the geology from the geologist, the system suggest new modelling features in the data. In this presentation we demonstrate the application of the results from the ERGO project, including the proposed modelling workflow utilized on a variety of data examples.

Mimicking the cell membrane: bio-inspired simultaneous functions with monovalent anion selectivity and antifouling properties of anion exchange membrane

PubMed Central

Zhao, Yan; Liu, Huimin; Tang, Kaini; Jin, Yali; Pan, Jiefeng; der Bruggen, Bart Van; Shen, Jiangnan; Gao, Congjie

2016-01-01

A new bio-inspired method was applied in this study to simultaneously improve the monovalent anion selectivity and antifouling properties of anion exchange membranes (AEMs). Three-layer architecture was developed by deposition of polydopamine (PDA) and electro-deposition of N-O-sulfonic acid benzyl chitosan (NSBC). The innermost and outermost layers were PDA with different deposition time. The middle layer was prepared by NSBC. Fourier transform infrared spectroscopy and scanning electron microscopy confirmed that PDA and NSBC were successfully modified on the surfaces of AEMs. The contact angle of the membranes indicated an improved hydrophilicity of the modified membranes. A series of electrodialysis experiments in which Cl−/SO42− separation was studied, demonstrating the monovalent anion selectivity of the samples. The Cl−/SO42− permselectivity of the modified membranes can reach up to 2.20, higher than that of the commercial membrane (only 0.78) during 90 minutes in electrodialysis (ED). The increase value of the resistance of the membranes was also measured to evaluate the antifouling properties. Sodium dodecyl benzene sulfonate (SDBS) was used as the fouling material in the ED process and the membrane area resistance of modified membrane increase value of was only 0.08 Ωcm2 30 minutes later. PMID:27853255

Mimicking the cell membrane: bio-inspired simultaneous functions with monovalent anion selectivity and antifouling properties of anion exchange membrane.

PubMed

Zhao, Yan; Liu, Huimin; Tang, Kaini; Jin, Yali; Pan, Jiefeng; der Bruggen, Bart Van; Shen, Jiangnan; Gao, Congjie

2016-11-17

A new bio-inspired method was applied in this study to simultaneously improve the monovalent anion selectivity and antifouling properties of anion exchange membranes (AEMs). Three-layer architecture was developed by deposition of polydopamine (PDA) and electro-deposition of N-O-sulfonic acid benzyl chitosan (NSBC). The innermost and outermost layers were PDA with different deposition time. The middle layer was prepared by NSBC. Fourier transform infrared spectroscopy and scanning electron microscopy confirmed that PDA and NSBC were successfully modified on the surfaces of AEMs. The contact angle of the membranes indicated an improved hydrophilicity of the modified membranes. A series of electrodialysis experiments in which Cl - /SO 4 2- separation was studied, demonstrating the monovalent anion selectivity of the samples. The Cl - /SO 4 2- permselectivity of the modified membranes can reach up to 2.20, higher than that of the commercial membrane (only 0.78) during 90 minutes in electrodialysis (ED). The increase value of the resistance of the membranes was also measured to evaluate the antifouling properties. Sodium dodecyl benzene sulfonate (SDBS) was used as the fouling material in the ED process and the membrane area resistance of modified membrane increase value of was only 0.08 Ωcm 2 30 minutes later.

Development of an Advanced Animal Habitat for Spaceflight

NASA Technical Reports Server (NTRS)

Baer, L.; Vasques, M.; Martwick, F.; Hines, M.; Grindeland, R. E.

1994-01-01

It is necessary to fly a group-housed animals for many Life Science spaceflight studies. Currently, group-housed rodents are flown aboard the shuttle in the Animal Enclosure Module (AEM). Although the AEM has been used successfully for a number of flights, it has significant limitations in the number of animals it can accommodate, limited flight duration, passive temperature control and limited in flight data acquisition capability. An Advanced Animal Habitat (AAH) is being developed, which can be flown on the shuttle middeck, both spacelab and spacehab shuttle payload modules, and the space station. The AAH is designed to house 12 rats or 30 mice for up to 30 days. The AAH will have active temperature control, a window mechanism to facilitate video monitoring/recording of the animals, and biotelemetry capabilities. In addition, the design will permit access to the animals for experimental manipulations in space. The AAH can be refitted to experiment-specific requirements as needed. In initial 7-day hardware tests 12 male rats and 10 female mice show no adverse affects with respect to final body and organ weights as compared to vivarium. controls. The Advanced Animal Habitat will provide the science community opportunities to perform a greater variety of studies for longer duration in the microgravity environment than the current Animal Enclosure Module.

Mimicking the cell membrane: bio-inspired simultaneous functions with monovalent anion selectivity and antifouling properties of anion exchange membrane

NASA Astrophysics Data System (ADS)

Zhao, Yan; Liu, Huimin; Tang, Kaini; Jin, Yali; Pan, Jiefeng; der Bruggen, Bart Van; Shen, Jiangnan; Gao, Congjie

2016-11-01

A new bio-inspired method was applied in this study to simultaneously improve the monovalent anion selectivity and antifouling properties of anion exchange membranes (AEMs). Three-layer architecture was developed by deposition of polydopamine (PDA) and electro-deposition of N-O-sulfonic acid benzyl chitosan (NSBC). The innermost and outermost layers were PDA with different deposition time. The middle layer was prepared by NSBC. Fourier transform infrared spectroscopy and scanning electron microscopy confirmed that PDA and NSBC were successfully modified on the surfaces of AEMs. The contact angle of the membranes indicated an improved hydrophilicity of the modified membranes. A series of electrodialysis experiments in which Cl-/SO42- separation was studied, demonstrating the monovalent anion selectivity of the samples. The Cl-/SO42- permselectivity of the modified membranes can reach up to 2.20, higher than that of the commercial membrane (only 0.78) during 90 minutes in electrodialysis (ED). The increase value of the resistance of the membranes was also measured to evaluate the antifouling properties. Sodium dodecyl benzene sulfonate (SDBS) was used as the fouling material in the ED process and the membrane area resistance of modified membrane increase value of was only 0.08 Ωcm2 30 minutes later.

Into the wardrobe of Narnia: beyond HIV infection a world of cardiovascular risk.

PubMed

Colotto, Marco; Renzi, Alessandra; Durante, Cosimo

2012-07-17

A 38-years-old HIV-hepatitis C virus (HCV) coinfected woman presented to us for dyslipidemia. Clinical, familial and laboratory data were consistent with the diagnosis of familial heterozygous hypercholesterolaemia. History, clinical examination and laboratory findings also supported suspected acromegaly. A pituitary MRI showed a sellar macroadenoma that was removed by transphenoidal surgery without complications. MRI carried out 6 months after surgery showed almost complete removal of the adenoma. This case report describes an uncommon association of diseases, very different for aetiology--genetic for FH, infectious for HIV and HCV, caused by excessive hormone secretion for acromegaly--clinical features and therapy, but all sharing a significant impact on cardiovascular risk as a common feature.

Science to Support DOE Site Cleanup: The Pacific Northwest National Laboratory Environmental Management Science Program Awards-Fiscal Year 1999 Mid-Year Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peurrung, L.M.

1999-06-30

Pacific Northwest National Laboratory was awarded ten Environmental Management Science Program (EMSP) research grants in fiscal year 1996, six in fiscal year 1997, and eight in fiscal year 1998. This section summarizes how each grant addresses significant U.S. Department of Energy (DOE) cleanup issues, including those at the Hanford Site. The technical progress made to date in each of these research projects is addressed in more detail in the individual progress reports contained in this document. This research is focused primarily in five areas: Tank Waste Remediation, Decontamination and Decommissioning, Spent Nuclear Fuel and Nuclear Materials, Soil and Groundwater Cleanmore » Up, and Health Effects.« less

GROUNDWATER REMEDIATION SOLUTIONS AT HANFORD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilmore, Tyler J.; Truex, Michael J.; Williams, Mark D.

2007-02-26

In 2006, Congress provided funding to the U. S. Department of Energy (DOE) to study new technologies that could be used to treat contamination from the Hanford Site that might impact the Columbia River. The contaminants of concern are primarily metals and radionuclides, which are byproducts of Hanford’s cold war mission to produce plutonium for atomic weapons. The DOE asked Pacific Northwest National Laboratory (PNNL) to consider this problem and develop approaches to address the contamination that threatens the river. DOE identified three high priority sites that had groundwater contamination migrating towards the Columbia river for remediation. The contaminants includedmore » strontium-90, uranium and chromium. Remediation techniques for metals and radionuclides focus primarily on altering the oxidation state of the contaminant chemically or biologically, isolating the contaminants from the environment through adsorption or encapsulation or concentrating the contaminants for removal. A natural systems approach was taken that uses a mass balance concept to frame the problem and determine the most appropriate remedial approach. This approach provides for a scientifically based remedial decision. The technologies selected to address these contaminants included an apatite adsorption barrier coupled with a phytoremediation to address the strontium-90 contamination, injection of polyphosphate into the subsurface to sequester uranium, and a bioremediation approach to reduce chromium contamination in the groundwater. The ability to provide scientifically based approaches is in large part due to work developed under previous DOE Office of Science and Office of Environmental Management projects. For example, the polyphosphate and the bioremediation techniques, were developed by PNNL under the EMSP and NABIR programs. Contaminated groundwater under the Hanford Site poses a potential risk to humans and the Columbia River. These new technologies holds great promise for effectively remediating the residual waste that threatens the environment.« less

Rapid reconnaissance hydrogeologic modeling on public lands using analytic element solutions coupled with MODFLOW - application to the Eagle Creek watershed, New Mexico

NASA Astrophysics Data System (ADS)

Congdon, R. D.

2012-12-01

There is frequently a need in land management agencies for a quick and easy method for estimating hydrogeologic conditions in a watershed for which there is very little subsurface information. Setting up a finite difference or finite element model takes valuable time that often is not available when decisions need to be made quickly. An analytic element model (AEM), GFLOW in this case, may enable the investigator to produce a preliminary steady-state model for a watershed, and to easily evaluate variants of the conceptual model. Use of preexisting data, such as stream gage data or USGS reports makes the job much easier. Solutions to analytic element models are obtained within seconds. The Eagle Creek watershed in central New Mexico is a site of local water supply issues in an area of volcanic and plutonic rocks. Parameters estimated by groundwater consultants and the USGS, and discharge data from three USGS stream gages were used to set up the steady-state analytical model (GFLOW). Matching gage records with line-sink fluxes facilitated conceptualization of local groundwater flow and quick analysis of the effects of steady water supply pumping on Eagle Creek. Because of steep topgraphy and limited access, a water supply well is located within the stream channel within 20 meters of the creek, and it would be useful to evaluate the effects of the well on stream flow. A USGS report (SIR 2010-5205) revealed a section of Eagle Creek with a high vertical conductivity which results in flow loss of up to 34 l/s (including flow to the water table and flow into alluvium) when the well was pumped and the water table was lowered below the channel bottom. The water supply well was simulated with a steady-state well pumping at the average and maximum rates of 12 l/s and 31 l/s. The initial simulation shows that pumping at these rates results in stream flow loss of 19% and 51%, respectively. The simulation was conducted with average flow conditions, and this information will be important in planning for management during periods of drought, as well as times of more normal precipitation; as water uses must be balanced with the needs of the existing ecosystem. Alternatives, such as low conductivity blocks between stream channels and different volumetric and geographic pumping scenarios may also be readily explored in an AEM. Exporting these scenarios into MODFLOW simulations will enable us to evaluate transient and cyclical pumping effects on the surface waters for each AEM conceptualization, as well as being able to simulate seasonal recharge. However, in many cases the use of MODFLOW may not be necessary, if the AEM proves sufficient to answer the relevant questions. Symbiotic use of GFLOW and MODFLOW will be an invaluable aid in evaluating groundwater and its uses in National Forest watersheds, especially in cases when time is a critical factor in informed decision-making.

Analytical electron microscopy of fine-grained phases in primitive interplanetary dust particles and carbonaceous chondrites

NASA Technical Reports Server (NTRS)

Mackinnon, Ian D. R.; Rietmeijer, Frans J. M.; Mckay, David S.

1987-01-01

In order to describe the total mineralogical diversity within primitive extraterrestrial materials, individual interplanetary dust particles (IDPs) collected from the stratosphere as part of the JSC Cosmic Dust Curatorial Program were analyzed using a variety of AEM techniques. Identification of over 250 individual grains within one chondritic porous (CP) IDP shows that most phases could be formed by low temperature processes and that heating of the IDP during atmospheric entry is minimal and less than 600 C. In a review of the mineralogy of IDPs, it was suggested that the occurrence of other silicates such as enstatite whiskers is consistent with the formation in an early turbulent period of the solar nebula. Experimental confirmation of fundamental chemical and physical processes in a stellar environment, such as vapor phase condensation, nucleation, and growth by annealing, is an important aspect of astrophysical models for the evolution of the Solar System. A detailed comparison of chondritic IDP and carbonaceous chondrite mineralogies shows significant differences between the types of silicate minerals as well as the predominant oxides.

Life Sciences Division Spaceflight Hardware

NASA Technical Reports Server (NTRS)

Yost, B.

1999-01-01

The Ames Research Center (ARC) is responsible for the development, integration, and operation of non-human life sciences payloads in support of NASA's Gravitational Biology and Ecology (GB&E) program. To help stimulate discussion and interest in the development and application of novel technologies for incorporation within non-human life sciences experiment systems, three hardware system models will be displayed with associated graphics/text explanations. First, an Animal Enclosure Model (AEM) will be shown to communicate the nature and types of constraints physiological researchers must deal with during manned space flight experiments using rodent specimens. Second, a model of the Modular Cultivation System (MCS) under development by ESA will be presented to highlight technologies that may benefit cell-based research, including advanced imaging technologies. Finally, subsystems of the Cell Culture Unit (CCU) in development by ARC will also be shown. A discussion will be provided on candidate technology requirements in the areas of specimen environmental control, biotelemetry, telescience and telerobotics, and in situ analytical techniques and imaging. In addition, an overview of the Center for Gravitational Biology Research facilities will be provided.

Electro-Optical Properties of Polymer Blends: Lasing, Electroluminescence and Photophysics

DTIC Science & Technology

2007-02-01

34- Phenylenevinylene" (Cirpan/Rathnayake/Lahti/Karasz) 16. Chem. Mater.: "Single-Molecule and Bulk Luminescence Studies of the Green Emission Band in 2,7- Bis...providing emission from the triplet state with a 100% theoretical yield. These electronic transitions of lanthanides result from different electronic...referred to above. Luminescence spectra and luminescence decays were recorded with a Thermo Laser Science pulsed nitrogen laser ( Aem =3 3 7 .1 nm; < 4 ns

Fully Burdened Cost of Fuel Using Input-Output Analysis

DTIC Science & Technology

2011-12-01

Distribution Model could be used to replace the current seven-step Fully Burdened Cost of Fuel process with a single step, allowing for less complex and...wide extension of the Bulk Fuels Distribution Model could be used to replace the current seven-step Fully Burdened Cost of Fuel process with a single...ABBREVIATIONS AEM Atlantic, Europe, and the Mediterranean AOAs Analysis of Alternatives DAG Defense Acquisition Guidebook DAU Defense Acquisition University

Publications - GMC 9 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

; Texaco West Kavik #1; Canning River B-1; ARCO Kavik #1; Forest Kemik #1; BP Kemik #2; Canning River A-1 ; Toolik Federal #1 Authors: Curiale, J.A. Publication Date: 1982 Publisher: Alaska Division of Geological eight North Slope wells: Mobil West Staines #2; Texaco West Kavik #1; Canning River B-1; ARCO Kavik #1

Block copolymers for alkaline fuel cell membrane materials

NASA Astrophysics Data System (ADS)

Li, Yifan

Alkaline fuel cells (AFCs) using anion exchange membranes (AEMs) as electrolyte have recently received considerable attention. AFCs offer some advantages over proton exchange membrane fuel cells, including the potential of non-noble metal (e.g. nickel, silver) catalyst on the cathode, which can dramatically lower the fuel cell cost. The main drawback of traditional AFCs is the use of liquid electrolyte (e.g. aqueous potassium hydroxide), which can result in the formation of carbonate precipitates by reaction with carbon dioxide. AEMs with tethered cations can overcome the precipitates formed in traditional AFCs. Our current research focuses on developing different polymer systems (blend, block, grafted, and crosslinked polymers) in order to understand alkaline fuel cell membrane in many aspects and design optimized anion exchange membranes with better alkaline stability, mechanical integrity and ionic conductivity. A number of distinct materials have been produced and characterized. A polymer blend system comprised of poly(vinylbenzyl chloride)-b-polystyrene (PVBC-b-PS) diblock copolymer, prepared by nitroxide mediated polymerization (NMP), with poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) or brominated PPO was studied for conversion into a blend membrane for AEM. The formation of a miscible blend matrix improved mechanical properties while maintaining high ionic conductivity through formation of phase separated ionic domains. Using anionic polymerization, a polyethylene based block copolymer was designed where the polyethylene-based block copolymer formed bicontinuous morphological structures to enhance the hydroxide conductivity (up to 94 mS/cm at 80 °C) while excellent mechanical properties (strain up to 205%) of the polyethylene block copolymer membrane was observed. A polymer system was designed and characterized with monomethoxy polyethylene glycol (mPEG) as a hydrophilic polymer grafted through substitution of pendent benzyl chloride groups of a PVBC-b-PS. The incorporation of the hydrophilic polymer allows for an investigation of the effect of hydration on ionic conductivity, resulting in the increase in membrane water affinity, enhancement of conductivity and reduced dependence of conductivity on relative humidity. A study of crosslinking of block copolymers was done wherein the crosslinking occurs in the non-matrix phase in order to maintain mechanical properties. The formation of a cationic crosslinked structure improves the mechanical integrity of the membrane in water while showing little deleterious effect on ionic conductivity and mechanical properties.

Possible relevance of tumor-related genes mutation to malignant transformation of endometriosis.

PubMed

Ma, X; Hui, Y; Lin, L; Wu, Y; Zhang, X; Qin, X

2016-01-01

Despite studies have suggested that endometriosis has malignant potential, the molecular mechanism underlying the malignant transformation of endometriosis is poorly understood so far. Endometriosis-associated ovarian cancer (EAOC) or ovarian cancer arising from endometriosis (OCEM) may provide an ideal model for genetic studies. To investigate the genetic alterations during transformation of ovarian endometriosis into cancer, the authors analysed mutations of tumour-related genes (PTEN and p53) in EAOC cases (n=23, group 1), including 19 cases which were detected co-existence of endometriosis and cancer and four cases which fulfilled the histological criteria in malignant transformation of endometriosis (OCEMs), and in atypical hyperplasia ovarian endometriosis (aEMs) (n = 10, group 2), as well as in solitary ovarian endometriosis (EMs) (n = 20, group 3), simultaneously, to study the correlation of the two genes in the development and progression of the ovarian endometriosis malignancy. Each paraffin block was sliced into serial ten-µm-thick sections. Extracted DNA was amplified by nested PCR. Mutations of PTEN and p53 were examined by bidirectional DNA sequencing. It was acknowledged by experiments that the PTEN and p53 mutation frequency in EAOCs were significantly higher than that in aEMs and EMs. There was significant difference to compare EAOCs with EMs (p < 0.01, p < 0.05), and converse to compare with aEMs (p > 0.05), respectively. No definite involvement between the frequency of PTEN and p53 mutations in EAOCs and age difference, histological type, clinical stage, pathological grade, and whether accompanied by metastasis (p > 0.05); however, a decreasing trend of PTEN mutation with the increased age, decreased clinical stage and pathological grade, and when accompanied by metastasis was detected. Adversely, an increasing trend of p53 mutation was represented. In EAOCs group, the authors detected eight PTEN and four p53 mutation events, respectively. Moreover, one case occurred PTEN and p53 mutation simultaneously. With 23 EAOCs, two cases which fulfilled the histological criteria in malignant transformation of endometriosis, which may be a specific entity distinct from non-endometriosis-associated ovarian cancer, the authors named them the OCEMs, occurred PTEN or p53 mutation, respectively. The present study suggested that the mutation and functional incapacitation of certain tumor-related genes may be involved in malignant transformation of endometriosis. PTEN mutation is the pristine event, but p53 mutation is the late.

Challenges of Zinc-Specific Transrectal Fluorescence Tomography to Detect Prostate Cancer

DTIC Science & Technology

2012-10-01

wavelength, aem  and sem as those at emission wavelength, afl as the absorption coefficient of the fluorophore at the excitation wavelength,  as the...tentatively accepted” by Medical Physics at the time of this annual report being submitted. The current pre-doctoral trainee PI is Mr. Anqi Zhang. The...year 2 report thus contains progresses contributed by both the former and current trainee PIs. During the year 2 of this study, we have furthered

The ROWPU Prefiltration System: Removal of Microorganisms

DTIC Science & Technology

1982-03-01

Pressman4 studied the performance of a prototype Rt(PTT filter rated at 360 gallons per hour. Raw river water was seeded with f2 coliphage virus prior to...block umaiber) Bacillus slobgii Water treatment Easheiebia foilr Cartridge filter Pouioviru Total aerobic bacteriaPalioirusTotal enteric bacteria 246...TTIACT ~ndo aEm. tom ebNi nmoveo -d hoioN 67 asoft aowl6) The Army has developed a Pleverse Osmosis Water Purification Unit (ROWPIT) to provide potable

Analysis of Double Layer and Adsorption Effects at the Alkaline Polymer Electrolyte-Electrode Interface

DTIC Science & Technology

2011-10-05

anion exchange mem - branes (AEM) are an attractive alternative to proton exchange mem - brane (PEM) fuel cells.1, 2 From electrocatalysts standpoint...gener- ally broken down into three distinct regions: the inner Helmholtz plane (IHP), the outer Helmholtz plane ( OHP ), and the diffuse layer. Figure 11...closest approach and is defined as OHP at a distance, x2. Nonspecifically adsorbed ions are distributed in a three dimensional region, called diffuse layer

Poly(2,6-dimethyl-1,4-phenylene oxide) Blended with Poly (vinylbenzyl chloride)-b-polystyrene for the Formation of Anion Exchange Membranes

DTIC Science & Technology

2014-08-14

show improved mechanical properties compared to the styrenic copolymer, particularly in a hydrated condition. The membranes were subjected to...AEMs) show improved mechanical properties compared to the styrenic copolymer, particularly in a hydrated condition. The membranes were subjected to...deionized water, and after 24 h of soaking, the fully hydrated membranes were removed from the water; any residual bulk water on the membrane surface was

On-orbit checkout of satellites, volume 2. Part 3 of on-orbit checkout study. [space maintenance

NASA Technical Reports Server (NTRS)

Pritchard, E. I.

1978-01-01

Early satellite failures significantly degrading satellite operations are reviewed with emphasis on LANDSAT D, the Technology Demonstration Satellite, the ATREX/AEM spacecraft, STORMSAT 2, and the synchronous meteorological satellite. Candidates for correction with on-orbit checkout and appropriate actions are analyzed. On-orbit checkout subsystem level studies are summarized for electrical power, attitude control, thermal control, reaction control and propulsion, instruments, and angular rate matching for alignment of satellite IRU.

Airborne Electromagnetic Mapping of Peatlands: a Case Study in Norway.

NASA Astrophysics Data System (ADS)

Silvestri, S.; Viezzoli, A.; Pfaffhuber, A. A.; Vettore, A.

2017-12-01

Peatlands are extraordinary reservoirs of organic carbon that can be found over a wide range of latitudes, in tropical, to temperate, to (sub)polar climates. According to some estimates, the carbon stored in peatlands almost match the atmospheric carbon pool. Peatlands degradation due to natural and anthropogenic factors releases every year large amount of CO2 and other green house gasses into the atmosphere. The conservation of peatlands is therefore a key measure to reduce emissions and to mitigate climate change. An effective plan to prevent peatlands degradation must move from a precise estimate of the volume of peat stored across vast territories around the world. One example are the several bogs that characterize large surfaces in Norway. Our research combines the use of high spatial resolution satellite optical data with Airborne Electromagnetic (AEM) and field measurements in order to map the extension and thickness of peat in Brøttum, Ringsaker province, Norway. The methodology allows us to quantify the volume of peat as well as the organic carbon stock. The variable thickness typical of Norwegian bogs allows us to test the limits of the AEM methodology in resolving near surface peat layers. This project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 747809. Start date: 1 June 2017. Duration: 24 months

3D inversion of SPECTREM and ZTEM airborne electromagnetic data from the Pebble Cu-Au-Mo porphyry deposit, Alaska

NASA Astrophysics Data System (ADS)

Pare, Pascal; Gribenko, Alexander V.; Cox, Leif H.; Čuma, Martin; Wilson, Glenn A.; Zhdanov, Michael S.; Legault, Jean; Smit, Jaco; Polome, Louis

2012-04-01

Geological, geochemical, and geophysical surveys have been conducted in the area of the Pebble Cu-Au-Mo porphyry deposit in south-west Alaska since 1985. This case study compares three-dimensional (3D) inversion results from Anglo American's proprietary SPECTREM 2000 fixed-wing time-domain airborne electromagnetic (AEM) and Geotech's ZTEM airborne audio-frequency magnetics (AFMAG) systems flown over the Pebble deposit. Within the commonality of their physics, 3D inversions of both SPECTREM and ZTEM recover conductivity models consistent with each other and the known geology. Both 3D inversions recover conductors coincident with alteration associated with both Pebble East and Pebble West. The high grade CuEqn 0.6% ore shell is not consistently following the high conductive trend, suggesting that the SPECTREM and ZTEM responses correspond in part to the sulphide distribution, but not directly with the ore mineralization. As in any exploration project, interpretation of both surveys has yielded an improved understanding of the geology, alteration and mineralization of the Pebble system and this will serve well for on-going exploration activities. There are distinct practical advantages to the use of both SPECTREM and ZTEM, so we draw no recommendation for either system. We can conclude however, that 3D inversion of both AEM and ZTEM surveys is now a practical consideration and that it has added value to exploration at Pebble.

Land subsidence in the Yangtze River Delta, China revealed from multi-frequency SAR Interferometry

NASA Astrophysics Data System (ADS)

Li, Zhenhong; Motagh, Mahdi; Yu, Jun; Gong, Xulong; Wu, Jianqiang; Zhu, Yefei; Chen, Huogen; Zhang, Dengming; Xu, Yulin

2014-05-01

Land subsidence is a major worldwide hazard, and its principal causes are subsurface fluid withdrawal, drainage of organic soils, sinkholes, underground mining, hydrocompaction, thawing permafrost, and natural consolidation. Land subsidence causes many problems including: damage to public facilities such as bridges, roads, railroads, electric power lines, underground pipes; damage to private and public buildings; and in some cases of low-lying land, can increase the risk of coastal flooding from storm surges and rising sea-levels. In China, approximately 48600 km2 of land, an area roughly 30 times of the size of the Greater London, has subsided (nearly 50 cities across 16 provinces), and the annual direct economic loss is estimated to be more than RMB 100 million (~12 million). It is believed that the Suzhou-Wuxi-Changzhou region within the Yangtze River Delta is the most severely affected area for subsidence hazards in China. With its global coverage and all-weather imaging capability, Interferometric SAR (InSAR) is revolutionizing our ability to image the Earth's surface and the evolution of its shape over time. In this paper, an advanced InSAR time series technique, InSAR TS + AEM, has been employed to analysed ERS (C-band), Envisat (C-band) and TerraSAR-X (X-band) data collected over the Suzhou-Wuxi-Changzhou region during the period from 1992 to 2013. Validation with precise levelling and GPS data suggest: (1) the accuracy of the InSAR-derived mean velocity measurements is 1-3 mm/yr; (2) InSAR-derived displacements agreed with precise levelling with root mean square errors around 5 mm. It is evident that InSAR TS + AEM can be used to image the evolution of deformation patterns in the Suzhou-Wuxi-Changzhou region over time: the maximum mean velocity decreased from ~12 cm/yr during the period of 1992-1993 to ~2 cm/yr in 2003-2013. This is believed to be a result of the prohibition of groundwater use carried out by Jiangsu provincial government. The combination of multi-frequency SAR datasets allows a long record (~20 years) of historic deformation to be measured over a large region. Ultimately this should help inform land managers in assessing land subsidence and planning appropriate remedial measures.

Metallurgical investigation into ductility dip cracking in nickel based alloys

NASA Astrophysics Data System (ADS)

Noecker, Fredrick F., II

A690 is a Ni-Cr-Fe alloy with excellent resistance to general corrosion, localized corrosion and stress corrosion cracking. However, the companion filler metal for A690, EN52, has been shown by several researchers to be susceptible to ductility dip cracking (DDC), which limits its widespread use in joining applications. The Gleeble hot ductility test was used to evaluate the DDC susceptibility of A600 and A690, along with their filler metals, EN82H and EN52, throughout the heating and cooling portions of a simulated weld reheat thermal cycle. Both macroscopic mechanical measures and microscopic measures of DDC were quantified and compared. Water quenching was conducted at select temperatures for subsequent microstructural characterization. Microstructural and microchemical characterization was carried out using scanning electron microscopy, transmission electron microscopy and analytical electron microscopy (AEM) techniques. The greatest resistance to DDC was observed in A600 and A690 during heating, where no DDC cracks formed even when the samples were fractured. Both A690 and EN52 were found to form an intermediate on-cooling dip in ductility and UTS, which corresponded to an increase in ductility dip crack length. The hot ductility and cracking resistance of EN82H remained high throughout the entire thermal cycle. DDC susceptibility in both EN52 and EN82H decreased when the thermal cycle was modified to promote coarsening/precipitation of intergranular carbides prior to straining. AEM analysis did not reveal any sulfur or phosphorous intergranular segregation in EN52 at 1600°F on-heating, on-cooling or after a 60 second hold. The ductility dip cracks were preferentially oriented at a 45° to the tensile axis and were of a wedge type appearance, both of which are characteristic of grain boundary sliding (GBS). Samples with microstructures that consisted of coarsened carbides and/or serrated grain boundaries, which are expected to decrease GBS, were found to be resistant to DDC. Based on the results of this work grain boundary sliding contributes to DDC, while sulfur and phosphorous embrittlement do not play a role in DDC of EN52 at the concentrations investigated. The dynamic precipitation of partially coherent intergranular M23C6 carbides at intermediate temperatures may exacerbate DDC in A690 and EN52, but requires further investigation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buck, E.C.; Dietz, N.L.; Bates, J.K.

Uranium contaminated soils from the Fernald Operation Site, Ohio, have been examined by a combination of optical microscopy, scanning electron microscopy with backscattered electron detection (SEM/BSE), and analytical electron microscopy (AEM). A method is described for preparing of transmission electron microscopy (TEM) thin sections by ultramicrotomy. By using these thin sections, SEM and TEM images can be compared directly. Uranium was found in iron oxides, silicates (soddyite), phosphates (autunites), and fluorite. Little uranium was associated with clays. The distribution of uranium phases was found to be inhomogeneous at the microscopic level.

Inactivation of Spores of Bacillus Species by Wet Heat: Studies on Single Spores Using Laser Tweezers Taman Spectroscopy

DTIC Science & Technology

2013-02-01

a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. a...Applied and Environmental Microbiology, (08 2011): 0. doi: 10.1128/ AEM .05031-11 11/13/2011 21.00 J. Liu, J. R. Faeder, P. Setlow, X. Yi. Synergism...individual spores was measured by fluorescence emission , while changes in spore refractility and the level of CaDPA were monitored by phase contrast

A Flexible Method for Production of Stable Atomic Clusters with Variable Size for Chemical and Catalytic Activity Studies

DTIC Science & Technology

2011-12-01

Figure 2. Picture of the spark discharge with Ga electrodes. dgap superconducting transition temperature would cause a jump in the AEM current ...failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE...materials such as gold, sodium, and aluminum will not form a sufficiently concentrated vapor cloud from a current -carrying wire to form aerosol

Synthesis and Characterization of Perfluoro Quaternary Ammonium Ion Exchange Membranes for Fuel Cell Applications

DTIC Science & Technology

2012-01-01

complex fuels (2, 4-6). Current research on alkali fuel cells is primarily focused on the development of a solid polymer anion exchange membrane ( AEM ...a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. a...research focus the last few decades due to their high power density and low emissions when operating with hydrogen fuel (1-3). Recently however

A Micro-Computer Based Decision Support System for Response Surface Methodology

DTIC Science & Technology

1990-03-01

d = -(a+em) *(gab+en)*x/ ((a+tem) *(qap+tem)); app = ap+d*az; bpp = bp+d*bz; aold = az; am = ap/ bpp ; bm = bp/ bpp ; az = app/ bpp ; bz = 1.0; if (( fabs (az...x = x+one; ser = ser+cof[j]/x; ) return (tmp+log(stp*ser));) double betacf(a,b,x) double a, b, x; ( double tem,qapqam,qab,em,d; double bz, bpp ,bp,bm...aold)) < (eps* fabs (az))) goto done; printf("lpause in BETACF\

An Analysis of DOD’s Standards of Conduct Applicable to Personnel Assigned to the Contracting Arena.

DTIC Science & Technology

1980-12-01

THIS PAS Mw bas aem, REPOIR DOCUM NTATION PAGE RED NMIucLrlTWs . NEPORT NUVOW .GOVT ACcSmow e 3. NECIPg~wTS CATALOG NUMMERa 4. TITLe (ad 1,N.J 1. TYPE...SnAnfards on CNui-t4haR boon- DO ~ 1473 EmalOm e e 6.OSŕ Vill 0802-014. 501 1 10 , TO P 1 , - woono-o--- - - a s fi developed for use by procurement...ASSUMPTIONS---------------------------------------- 11 E . LIMITATIONS---------------------------------------- 11 F. METHODOLOGY

Information Systems Strategy in Air Transport

DTIC Science & Technology

1993-09-01

revenues . Using a two-tier fare system rather than the single-tier low fare sustem of Pacific Southwest increased aircraft utilization and spread out fixed...1979, p. 82) In 1975 and 1976 Southwest made gains in both revenue and profits without a fare increase . Muse said, "I wanted to prove to those dumb...S16-788 S13746 102 APPENDIX E SSOUTHWEST AIRLINES CO. I m aeme ’s Discussion and Analysis The increase in passenger revenues , whicd accounted for 96

Junction Potentials Bias Measurements of Ion Exchange Membrane Permselectivity.

PubMed

Kingsbury, Ryan S; Flotron, Sophie; Zhu, Shan; Call, Douglas F; Coronell, Orlando

2018-04-17

Ion exchange membranes (IEMs) are versatile materials relevant to a variety of water and waste treatment, energy production, and industrial separation processes. The defining characteristic of IEMs is their ability to selectively allow positive or negative ions to permeate, which is referred to as permselectivity. Measured values of permselectivity that equal unity (corresponding to a perfectly selective membrane) or exceed unity (theoretically impossible) have been reported for cation exchange membranes (CEMs). Such nonphysical results call into question our ability to correctly measure this crucial membrane property. Because weighing errors, temperature, and measurement uncertainty have been shown to not explain these anomalous permselectivity results, we hypothesized that a possible explanation are junction potentials that occur at the tips of reference electrodes. In this work, we tested this hypothesis by comparing permselectivity values obtained from bare Ag/AgCl wire electrodes (which have no junction) to values obtained from single-junction reference electrodes containing two different electrolytes. We show that permselectivity values obtained using reference electrodes with junctions were greater than unity for CEMs. In contrast, electrodes without junctions always produced permselectivities lower than unity. Electrodes with junctions also resulted in artificially low permselectivity values for AEMs compared to electrodes without junctions. Thus, we conclude that junctions in reference electrodes introduce two biases into results in the IEM literature: (i) permselectivity values larger than unity for CEMs and (ii) lower permselectivity values for AEMs compared to those for CEMs. These biases can be avoided by using electrodes without a junction.

Using the in-line component for fixed-wing EM 1D inversion

NASA Astrophysics Data System (ADS)

Smiarowski, Adam

2015-09-01

Numerous authors have discussed the utility of multicomponent measurements. Generally speaking, for a vertical-oriented dipole source, the measured vertical component couples to horizontal planar bodies while the horizontal in-line component couples best to vertical planar targets. For layered-earth cases, helicopter EM systems have little or no in-line component response and as a result much of the in-line signal is due to receiver coil rotation and appears as noise. In contrast to this, the in-line component of a fixed-wing airborne electromagnetic (AEM) system with large transmitter-receiver offset can be substantial, exceeding the vertical component in conductive areas. This paper compares the in-line and vertical response of a fixed-wing airborne electromagnetic (AEM) system using a half-space model and calculates sensitivity functions. The a posteriori inversion model parameter uncertainty matrix is calculated for a bathymetry model (conductive layer over more resistive half-space) for two inversion cases; use of vertical component alone is compared to joint inversion of vertical and in-line components. The joint inversion is able to better resolve model parameters. An example is then provided using field data from a bathymetry survey to compare the joint inversion to vertical component only inversion. For each inversion set, the difference between the inverted water depth and ship-measured bathymetry is calculated. The result is in general agreement with that expected from the a posteriori inversion model parameter uncertainty calculation.

Introducing catalyst in alkaline membrane for improved performance direct borohydride fuel cells

NASA Astrophysics Data System (ADS)

Qin, Haiying; Lin, Longxia; Chu, Wen; Jiang, Wei; He, Yan; Shi, Qiao; Deng, Yonghong; Ji, Zhenguo; Liu, Jiabin; Tao, Shanwen

2018-01-01

A catalytic material is introduced into the polymer matrix to prepare a novel polymeric alkaline electrolyte membrane (AEM) which simultaneously increases ionic conductivity, reduces the fuel cross-over. In this work, the hydroxide anion exchange membrane is mainly composed of poly(vinylalcohol) and alkaline exchange resin. CoCl2 is added into the poly(vinylalcohol) and alkaline exchange resin gel before casting the membrane to introduce catalytic materials. CoCl2 is converted into CoOOH after the reaction with KOH solution. The crystallinity of the polymer matrix decreases and the ionic conductivity of the composite membrane is notably improved by the introduction of Co-species. A direct borohydride fuel cell using the composite membrane exhibits an open circuit voltage of 1.11 V at 30 °C, which is notably higher than that of cells using other AEMs. The cell using the composite membrane achieves a maximum power density of 283 mW cm-2 at 60 °C while the cell using the membrane without Co-species only reaches 117 mW cm-2 at the same conditions. The outstanding performance of the cell using the composite membrane benefits from impregnation of the catalytic Co-species in the membrane, which not only increases the ionic conductivity but also reduces electrode polarization thus improves the fuel cell performance. This work provides a new approach to develop high-performance fuel cells through adding catalysts in the electrolyte membrane.

The process of recovery of a schizoaffectively disordered mind: a psychoanalytic theory of the functional psychoses, the psychodynamic pentapointed cognitive construct theory.

PubMed

Steggles, Gillian Ruth May

2012-08-24

A schizoaffectively disordered young woman made a small study of her mind while she was in psychoanalytic psychotherapy so that she might understand herself better. She worked closely with her psychoanalyst, and with the researcher who wrote up her case. She had a very difficult time for 30 years, but by the end of that time emerged completely recovered and with a great zest for life. This paper provides rare positive/constructive data about the processes involved in a case of schizoaffective disorder that involved manic as well as depressive and schizophrenic symptoms, and also the patient's stages of recovery. It demonstrates how psychiatric and psychoanalytic principles are inextricably linked together both in understanding this patient's ordeals and in her successful treatment, and suggests the clinical potential for theoretical and practical engagement between psychiatry and psychoanalysis.

Environmental Radiation Effects: A Need to Question Old Paradigms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinton, T.G.; Bedford, J.; Ulsh, B.

2003-03-27

A historical perspective is given of the current paradigm that does not explicitly protect the environment from radiation, but instead, relies on the concept that if dose limits are set to protect humans then the environment is automatically protected as well. We summarize recent international questioning of this paradigm and briefly present three different frameworks for protecting biota that are being considered by the U.S. DOE, the Canadian government and the International Commission on Radiological Protection. We emphasize that an enhanced collaboration is required between what has traditionally been separated disciplines of radiation biology and radiation ecology if we aremore » going to properly address the current environmental radiation problems. We then summarize results generated from an EMSP grant that allowed us to develop a Low Dose Irradiation Facility that specifically addresses effects of low-level, chronic irradiation on multiple levels of biological organization.« less

The importance of an ECG: back to basics.

PubMed

Haidari, Golaleh; Gray, Kirsty; Kirubakaran, Senthil

2012-11-28

A 48-year-old man presented to accident and emergency with syncope on a background history of 3 weeks of increasing shortness of breath. He collapsed at home prompting admission. He was a smoker with a 30-pack-year history. On examination, he was found to be tachypnoeic and hypoxic, with a raised JVP and quiet heard sounds. He was haemodynamically stable and a chest x-ray showed right upper-lobe collapse. His resting ECG demonstrated electrical alternans prompting urgent referral to the cardiologist for echocardiography. This revealed a large pericardial effusion with evidence of right ventricular diastolic collapse. In view of this, he underwent urgent pericardiocentesis. A subsequent CT scan showed bilateral pleural effusions and multiple lung nodules. Both pericardial and pleural fluid cytology were reported as metastatic non-small cell adenocarcinoma. The pericardial fluid continued to reaccumulate requiring a pericardial window. He was referred to the oncology team for palliative chemotherapy.

Performance of polyethylene based radiation grafted anion exchange membrane with polystyrene-b-poly (ethylene/butylene)-b-polystyrene based ionomer using NiCo2O4 catalyst for water electrolysis

NASA Astrophysics Data System (ADS)

Gupta, Gaurav; Scott, Keith; Mamlouk, Mohamed

2018-01-01

A soluble anion exchange ionomer with high OH- ion conductivity comparable to that of H+ conductivity of Nafion is synthesised by chloromethylation of polystyrene-b-poly (ethylene/butylene)-b-polystyrene (SEBS) and used with NiCo2O4 electro-catalyst for water electrolysis. The ionomer has an ion exchange capacity of 1.9 mmol g-1 and ionic conductivity of 0.14 S cm-2 at 50 °C. The cell voltage at 20 °C at 100 mA cm-2 is 1.77 and 1.72 V in, 0.1 and 1.0 M NaOH, respectively, for an optimum loading of 10 mg cm-2 NiCo2O4. At 10 mg cm-2 NiCo2O4 electrolyser cell performance is at least equal to or superior to that of IrO2 at 2 mg cm-2 with excellent stability over 1 h. When the catalyst is sprayed on the GDL instead of CCM, the performance is further improved to 1.65 V at 100 mA cm-2 at 60 °C & 0.1 M KOH. The limited AEM electrolyser performance when operating with deionised water in comparison to PEM and alkaline electrolyser arises from the sluggish OER in the AEM environment equivalent to pH of 11.5 and the two orders of magnitude lower HER activity with respect to acid medium combined with the high Tafel slope of 120 mV dec-1.

Automatic mapping of the base of aquifer — A case study from Morrill, Nebraska

USGS Publications Warehouse

Gulbrandsen, Mats Lundh; Ball, Lyndsay B.; Minsley, Burke J.; Hansen, Thomas Mejer

2017-01-01

When a geologist sets up a geologic model, various types of disparate information may be available, such as exposures, boreholes, and (or) geophysical data. In recent years, the amount of geophysical data available has been increasing, a trend that is only expected to continue. It is nontrivial (and often, in practice, impossible) for the geologist to take all the details of the geophysical data into account when setting up a geologic model. We have developed an approach that allows for the objective quantification of information from geophysical data and borehole observations in a way that is easy to integrate in the geologic modeling process. This will allow the geologist to make a geologic interpretation that is consistent with the geophysical information at hand. We have determined that automated interpretation of geologic layer boundaries using information from boreholes and geophysical data alone can provide a good geologic layer model, even before manual interpretation has begun. The workflow is implemented on a set of boreholes and airborne electromagnetic (AEM) data from Morrill, Nebraska. From the borehole logs, information about the depth to the base of aquifer (BOA) is extracted and used together with the AEM data to map a surface that represents this geologic contact. Finally, a comparison between our automated approach and a previous manual mapping of the BOA in the region validates the quality of the proposed method and suggests that this workflow will allow a much faster and objective geologic modeling process that is consistent with the available data.

Sea Surface Temperature Serving as Determining Factors for Sea Turtle Locations in the Atlantic Ocean

DTIC Science & Technology

2007-01-11

thme *"e let 8eitem - uc m 61e~ a & & g~Sim".~a "b~ - a " m e asmg "ed a eee ed an A em iei g ,Wand uevleme N Sg oia fl , F so"men Sen aem ~ e w db...establish a correlation between sea turtle locations in the Atlantic Ocean in relation to sea surface temperature. Currently all five species of sea turtles...knowledge currently available on this endangered species. Further research should be conducted to determine the role of wind speed to the migration

Anion Transport in a Chemically Stable, Sterically Bulky alpha-C Modified Imidazolium Functionalized Anion Exchange Membrane

DTIC Science & Technology

2014-06-24

AEM is often inconvenient, as ambient carbon dioxide (at publication time, 400 ppm) will react with the OH− to form a mixture of CO3 2− and HCO3 − in... crystal . Spectra were obtained in the range 500−4000 cm−1, with 256 scans and a resolution of 8 cm−1. Figure 1. Structure of 1,4,5-trimethyl-2-(2,4,6...pulsed-field gradient nuclear magnetic resonance (PFG NMR) on an AVANCEIII NMR spectrometer with a 5 mm Bruker single -axis DIFF60L Z-diffusion probe. The

High-throughput simultaneous analysis of buprenorphine, methadone, cocaine, opiates, nicotine, and metabolites in oral fluid by liquid chromatography tandem mass spectrometry

PubMed Central

Concheiro, Marta; Gray, Teresa R.; Shakleya, Diaa M.

2011-01-01

A method for simultaneous determination of buprenorphine (BUP), norbuprenorphine (NBUP), methadone, 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine (EDDP), cocaine, benzoylecgonine (BE), ecgonine methyl ester (EME), anhydroecgonine methyl ester (AEME), morphine, codeine, 6-acetylmorphine (6AM), heroin, 6-acetylcodeine (6AC), nicotine, cotinine, and trans-3′-hydroxycotinine (OH-cotinine) by liquid chromatography tandem mass spectrometry in oral fluid (OF) was developed and extensively validated. Acetonitrile (800 μL) and OF (250 μL) were added to a 96-well Isolute-PPT+protein precipitation plate. Reverse-phase separation was achieved in 16 min and quantification was performed by multiple reaction monitoring. The assay was linear from 0.5 or 1 to 500 μg/L. Intraday, interday, and total imprecision were less than 13% (n=20), analytical recovery was 92–114% (n= 20), extraction efficiencies were more than 77% (n=5), and process efficiencies were more than 45% (n=5). Although ion suppression was detected for EME, cocaine, morphine, 6AC, and heroin (less than 56%) and enhancement was detected for BE and nicotine (less than 316%), deuterated internal standards compensated for these effects. The method was sensitive (limit of detection 0.2–0.8 μg/L) and specific (no interferences) except that 3-hydroxy-4-methoxyamphetamine interfered with AEME. No carryover was detected, and all analytes were stable for 24 h at 22 °C, for 72 h at 4 °C, and after three freeze–thaw cycles, except cocaine, 6AC, and heroin (22–97% loss). The method was applied to 41 OF specimens collected throughout pregnancy with a Salivette® OF collection device from an opioid-dependent BUP-maintained pregnant woman. BUP ranged from 0 to 7,400 μg/L, NBUP from 0 to 71 μg/L, methadone from 0 to 3 μg/L, nicotine from 32 to 5,020 μg/L, cotinine from 125 to 508 μg/L, OH-cotinine from 11 to 51 μg/L, cocaine from 0 to 419 μg/L, BE from 0 to 351 μg/L, EME from 0 to 286 μg/L, AEME from 0 to 7 μg/L, morphine from 0 to 22 μg/L, codeine from 0 to 1 μg/L, 6AM from 0 to 4 μg/L, and heroin from 0 to 2 μg/L. All specimens tested negative for EDDP and 6AC. This method permits a fast and simultaneous quantification of 16 drugs and metabolites in OF, with good selectivity and sensitivity. PMID:20652688

A Trans-disciplinary Hydrogeological Systems Analysis Approach for Identifying and Assessing Managed Aquifer Recharge Options: Example from the Darling River Floodplain, N.S.W., Australia

NASA Astrophysics Data System (ADS)

Lawrie, K.; Brodie, R. S.; Tan, K. P.; Halas, L.; Magee, J.; Gow, L.; Christensen, N. B.

2013-12-01

Surface water availability and quality generally limits managed aquifer recharge (MAR) opportunities in inland Australia's highly salinized landscapes and groundwater systems. Economic factors also commonly limit MAR investigations to shallow freshwater groundwater systems near existing infrastructure. Aquifer opportunities lie mainly in zones of fresh groundwater in relatively thin fluvial sedimentary aquifer systems with highly variable hydraulic properties. As part of a broader strategy to identify water savings in the Murray-Darling Basin, the Broken Hill Managed Aquifer Recharge (BHMAR) project was tasked with identifying and assessing MAR and/or groundwater extraction options to reduce evaporative losses from existing surface water storages, secure Broken Hill's water supply, protect the local environment and heritage, and return water to the river system. A trans-disciplinary research approach was used to identify and assess MAR options across a broad area of the Darling River floodplain. This methodology enabled the team to recognise fundamental problems in discipline approaches, helped identify critical data gaps, led to significant innovation across discipline boundaries, was critical in the development of a new hydrogeological conceptual model, facilitated development of new models of landscape, geological and tectonic evolution of the study area, and enabled completion of pre-commissioning maximal and residual MAR risk assessments. An airborne electromagnetics (AEM) survey, acquired over a large (>7,500 sq km) area of the Darling Floodplain, enabled rapid identification of a multi-layer sequence of aquifers and aquitards, while a phased assessment methodology was developed to rapidly identify and assess over 30 potential MAR targets (largely in fresh groundwater zones within palaeochannels and at palaeochannel confluences). Hydraulic properties were confirmed by a 7.5 km drilling program (100 sonic and rotary mud holes), and complementary field (including limited pump tests) and laboratory measurements. Recognition of significant Neogene-to-Present faulting, warping and tilting of the unconsolidated sediments (using AEM, airborne magnetics, regional gravity, LiDAR and drilling data) was critical to understanding recharge, inter-aquifer leakage and potential environmental impacts of MAR options. A program of borehole Nuclear Magnetic Resonance (NMR) logging provided a record of near-continuous variations in K through the saturated sedimentary sequence, with the NMR data integrated with other borehole and AEM data to produce 3D maps of aquifer transmissivity. A priority site was identified where aquifer storage and recovery (ASR) options were assessed. Maximal and residual risk assessments of 12 hazard types included hydrogeological modelling, laboratory column clogging studies and geochemical assessment to identify source water treatment requirements. The study found that the residual scientific/technical risks for ASR at the priority site are low if the supplementary water treatment trains are included.

Nature and origin of interstellar diamond from the Allende CV3 meteorite

NASA Technical Reports Server (NTRS)

Blake, David; Freund, Friedemann; Bunch, Ted; Krishnan, Kannan; Stampfer, Mitch; Chang, Sherwood; Tielens, Alexander G. G. M.

1990-01-01

Data and experimental evidence which support the contention that the C delta diamonds may result from grain-grain collisions in supernova shocks in the interstellar medium are presented. Fragments of the Allende CV3 chondrite were acid-treated. A whitish powder was obtained. For the Analytical Electron Microscopy (AEM) a small drop of ethanol suspension was transferred onto holey carbon support films on 3 mm EM grids. The AEM was performed on transmission-thin fragments of the material which overlay holes in the film, to eliminate interference from the substrate. Electron Spectroscopy for Chemical Analysis (ESCA) was performed on a large aliquot of C. Diamond was identified by selected area electron diffraction. Scanning Transmission Electron Microscope / Energy Dispersive X-ray (STEM-EDS) microanalyses of the C delta diamond, using a light-element detector, show that oxygen and possibly nitrogen are the only impurities consistently present. ESCA spectra from bulk C delta material confirm the presence of N at a level of 0.35 percent or less. Under UV irradiation a yellow-red fluorescence is observed, consistent with that of natural diamonds containing substitutional N. Electron Energy Loss Spectra (EELS) were recorded at 2 eV resolution from the C delta diamond, high pressure synthetic diamond, a diamond film produced in a low pressure plasma by chemical vapor deposition (CVD) on a heated silicon substrate (Roy, 1987), graphite, and amorphous arc sputtered carbon. Comparison of the carbon K edge shape and fine structure shows the Allende C delta phase to be largely diamond, but with a significant pre-edge absorption feature indicative of transitions of C 1s electrons into pi asterisk orbitals which are absent in the purely sp(3)-bonded diamond but present in graphite and amorphous carbon.

Physiological Anatomical Rodent Experiment (PARE): 04 Flight Support

NASA Technical Reports Server (NTRS)

Burden, Hubert W.

1997-01-01

Rats were shipped to Kennedy Space Center (KSC), Florida, on day 2 of gestation [(G2) (day 1 = morning on which spermatozoa are present in the vagina)] and laparotomized on G7 to determine the number of implantation sites in each uterine horn. On G8, ten pregnant rats meeting flight criteria (at least five implantation sites each horn) were placed into NASA flight cages (animal enclosure modules, AEMS, five rats per cage), loaded onto the mid-deck of the space shuttle Atlantis, and on G9 (November 3, 1994) they were launched into orbit. On gestation day 20, (November 14, 1994) the shuttle returned to Edwards Air Force Base, California and the flight animals were recovered from the shuttle and subjected to unilateral hysterectomy to provide fetal material from one horn to investigators identified by NASA to study selected fetal parameters. After unilateral hysterectomy, the animals were allowed to recover and deliver vaginally. There were three groups (n = 10 each group) of control animals housed at KSC in the study. A synchronous control group, delayed 24 hours with reference to the flight group, received the same surgeries and was housed five rats per AEM and exposed to all flight conditions (identical temperatures, lighting and humidity) except microgravity. Vivarium control group I did not receive any surgery and was housed in the vivarium in clear polycarbonate cages. Vivarium control group 2 received only a unilateral hysterectomy on day 20 of gestation but otherwise was housed like the vivarium control group 1. Control groups were allowed to complete their pregnancy and deliver fetuses from the remaining horn (Synchronous control and vivarium control group 2) or horns (Vivarium control group 1). After surgery, the dams were euthanized and tissues recovered, and the neonates were assigned to foster dams.

Quantifying Federal Funding and Scholarly Output Related to the Academic Emergency Medicine Consensus Conferences

PubMed Central

Nishijima, Daniel K.; Dinh, Tu; May, Larissa; Yadav, Kabir; Gaddis, Gary M.; Cone, David C.

2014-01-01

Purpose Since 2000, Academic Emergency Medicine (AEM), the journal of the Society for Academic Emergency Medicine, has presented a one-day consensus conference to generate a research agenda for advancement of a scientific topic. One of the 12 annual issues of AEM is reserved for the proceedings of these conferences. The purpose of this study was to measure academic productivity of these conferences by evaluating subsequent federal research funding received by authors of conference manuscripts and calculating citation counts of conference papers. Method This was a cross-sectional study conducted during August and September 2012. NIH RePORTER was searched to identify subsequent federal funding obtained by authors of the consensus conference issues from 2000 to 2010. Funded projects were coded as related or unrelated to conference topic. Citation counts for all conference manuscripts were quantified using Scopus and Google Scholar. Simple descriptive statistics were reported. Results 852 individual authors contributed to 280 papers published in the 11 consensus conference issues. 137 authors (16%) obtained funding for 318 projects. A median of 22 topic-related projects per conference (range 10–97 projects) accounted for a median of $20,488,331 per conference (range $7,779,512–122,918,205). The average (±SD) number of citations per paper was 15.7 ±20.5 in Scopus and 23.7 ±32.6 in Google Scholar. Conclusions The authors of consensus conference manuscripts obtained significant federal grant support for follow-up research related to conference themes. In addition, the manuscripts generated by these conferences were frequently cited. Conferences devoted to research agenda development appear to be an academically worthwhile endeavor. PMID:24280853

Effects of Microgravity On Oxidative and Antioxidant Enzymes In Mouse Hindlimb Muscle

NASA Technical Reports Server (NTRS)

Girten, B.; Hoopes, R.; Steele, M.; Morony, S.; Bateman, T. A.; Sun, S. (Technical Monitor)

2002-01-01

Gastrocnemius muscle of mice were analyzed in order to examine the effects of 12 days of microgravity on the oxidative enzyme climate synthase (CS) and the antioxidant enzyme superoxide dismutase (SOD). The female C57BL/6J mice utilized for this study were part of the Commercial Biomedical Testing Module (CBTM) payload that flew aboard STS-108. Mice were housed in Animal Enclosure Modules (AEMs) provided by NASA Ames. The flight (FLT) group and the ground control (CON) group each had 12 mice per group. The AEMs that held the CON group operated on a 48-hour delay from the FLT group and were located inside the Orbital Environmental Simulator (OES) at Kennedy Space Center. The temperature, CO2 and relative humidity inside the OES was regulated based on downlinked information from the shuttle middeck. Student T tests were used to compare groups and a p < 0.05 was used to determine statistical significance. Results indicated that CS levels for the FLT group were significantly lower than the CON group while the SOD levels were significantly higher. The CS FLT mean was 19% lower and the SOD FLT mean was 17% higher than the respective CON group means. Although these findings are among the first muscle enzyme values reported for mice from a shuttle mission, these results are similar to some results previously reported for rats exposed to microgravity or hindlimb suspension. The changes seen during the CBTM payload are reflective of the deconditioning that takes place with disuse of the hindlimbs and indicate that muscle enzyme changes induced by disuse deconditioning are similar in both rodent species.

Simultaneous determination of cocaine/crack and its metabolites in oral fluid, urine and plasma by liquid chromatography-mass spectrometry and its application in drug users.

PubMed

Fiorentin, Taís Regina; D'Avila, Felipe Bianchini; Comiran, Eloisa; Zamboni, Amanda; Scherer, Juliana Nichterwitz; Pechansky, Flavio; Borges, Paulo Eduardo Mayorga; Fröehlich, Pedro Eduardo; Limberger, Renata Pereira

2017-07-01

A single LC-MS equipment was used to validate three methods for simultaneously analyzing cocaine (COC), benzoylecgonine (BZE), cocaethylene (CE), anhydroecgonine methyl ester (AEME) and anhydroecgonine (AEC) in oral fluid (OF), urine and plasma. The methods were carried out using a Kinetex HILIC column for polar compounds at 30°C. Mobile phase with isocratic condition of acetonitrile: 13mM ammonium acetate pH 6.0: methanol (55:35:10 v/v/v) at 0.8mL/min flow rate was used. After buffer dilution (OF) and protein precipitation (urine and plasma), calibration curve ranges were 4.25-544ng/mL for oral fluid and 5-320ng/mL for urine and plasma with correlation coefficients (r) between 0.9947 and 0.9992. The lowest concentration of the calibration curves were the lower limit of quantification. No major matrix effect could be noted, demonstrating the efficiency of the cleaning procedure. The methods were fully validated and proved to be suitable for analysis of 124 cocaine and/or crack cocaine users. Among the subjects, 56.5% reported daily use of cocaine in the previous three months. Results show a high prevalence of the analytes, with BZE as the most prevalent (94 cases), followed by COC (93 cases), AEC (70 cases), CE (33 cases) and AEME (13 cases). In addition, the concentration of BZE in urine was higher compared to OF and plasma found in the real samples, showing the facility of accumulation in chronic users in matrices with a large detection window. Copyright © 2017 Elsevier Inc. All rights reserved.

Significance of Landsat-7 Spacecraft Level Thermal Balance and Thermal Test for ETM+Instrument

NASA Technical Reports Server (NTRS)

Choi, Michael K.

1999-01-01

The thermal design and the instrument thermal vacuum (T/V) test of the Landsat-7 Enhanced Thematic Mapper Plus (ETM+) instrument were based on the Landsat-4, 5 and 6 heritage. The ETM+ scanner thermal model was also inherited from Landsat-4, 5 and 6. The temperature predictions of many scanner components in the original thermal model had poor agreement with the spacecraft and instrument integrated sun-pointing safehold (SPSH) thermal balance (T/B) test results. The spacecraft and instrument integrated T/B test led to a change of the Full Aperture Calibrator (FAC) motor stack "solar shield" coating from MIL-C-5541 to multi-layer insulation (MLI) thermal blanket. The temperature predictions of the Auxiliary Electronics Module (AEM) in the thermal model also had poor agreement with the T/B test results. Modifications to the scanner and AEM thermal models were performed to give good agreement between the temperature predictions and the test results. The correlated ETM+ thermal model was used to obtain flight temperature predictions. The flight temperature predictions in the nominal 15-orbit mission profile, plus margins, were used as the yellow limits for most of the ETM+ components. The spacecraft and instrument integrated T/B and TN test also revealed that the standby heater capacity on the Scan Mirror Assembly (SMA) was insufficient when the Earth Background Simulator (EBS) was 1 50C or colder, and the baffle heater possibly caused the coherent noise in the narrow band data when it was on. Also, the cooler cool-down was significantly faster than that in the instrument T/V test, and the coldest Cold Focal Plane Array (CFPA) temperature achieved was colder.

The 2016 Academic Emergency Medicine Consensus Conference, Shared Decision Making in the Emergency Department: Development of a Policy-relevant Patient-centered Research Agenda May 10, 2016, New Orleans, LA.

PubMed

Grudzen, Corita R; Anderson, Jana R; Carpenter, Christopher R; Hess, Erik P

2016-12-01

Shared decision making in emergency medicine has the potential to improve the quality, safety, and outcomes of emergency department (ED) patients. Given that the ED is the gateway to care for patients with a variety of illnesses and injuries and the safety net for patients otherwise unable to access care, shared decision making in the ED is relevant to numerous disciplines and the interests of the United States (U.S.) public. On May 10, 2016 the 16th annual Academic Emergency Medicine (AEM) consensus conference, "Shared Decision Making: Development of a Policy-Relevant Patient-Centered Research Agenda" was held in New Orleans, Louisiana. During this one-day conference clinicians, researchers, policy-makers, patient and caregiver representatives, funding agency representatives, trainees, and content experts across many areas of medicine interacted to define high priority areas for research in 1 of 6 domains: 1) diagnostic testing; 2) policy, 3) dissemination/implementation and education, 4) development and testing of shared decision making approaches and tools in practice, 5) palliative care and geriatrics, and 6) vulnerable populations and limited health literacy. This manuscript describes the current state of shared decision making in the ED context, provides an overview of the conference planning process, the aims of the conference, the focus of each respective breakout session, the roles of patient and caregiver representatives and an overview of the conference agenda. The results of this conference published in this issue of AEM provide an essential summary of the future research priorities for shared decision making to increase quality of care and patient-centered outcomes. © 2016 by the Society for Academic Emergency Medicine.

Histidine at Position 195 is Essential for Association of Heme- b in Lcp1VH2

NASA Astrophysics Data System (ADS)

Oetermann, Sylvia; Vivod, Robin; Hiessl, Sebastian; Hogeback, Jens; Holtkamp, Michael; Karst, Uwe; Steinbüchel, Alexander

2018-05-01

The latex clearing protein (Lcp) is the key enzyme of polyisoprene degradation in actinomycetes (Yikmis and Steinbüchel in Appl Environ Microbiol 78:4543-4551, https://doi.org/10.1128/AEM.00001-12 , 2012). In this study it was shown that Lcp from Gordonia polyisoprenivorans VH2 (Lcp1VH2) harbors a non-covalently bound heme b as cofactor, which was identified by pyridine hemochrome spectra and confirmed by LC/ESI-ToF-MS. It contains iron, most likely in the Fe3+ state. We focused on the characterization of the heme-cofactor, its accessibility with respect to the conformation of Lcp1VH2, and the identification of putative histidine residues involved in the coordination of heme. A change was detectable in UV/Vis-spectra of reduced Lcp1VH2 when imidazole was added, showing that Lcp1VH2 "as isolated" occurs in an open state, directly being accessible for external ligands. In addition, three highly conserved histidines (H195, H200 and H228), presumably acting as ligands coordinating the heme within the heme pocket, were replaced with alanines by site-directed mutagenesis. The effect of these changes on in vivo rubber-mineralization was investigated. The lcp- deletion mutant complemented with the H195A variant of lcp1 VH2 was unable to mineralize poly( cis-1,4-isoprene). In vitro analyses of purified, recombinant Lcp1VH2H195A confirmed the loss of enzyme activity, which could be ascribed to the loss of heme. Hence, H195 is essential for the association of heme- b in the central region of Lcp1VH2.

USArray Siting Outreach: Telling the EarthScope Story

NASA Astrophysics Data System (ADS)

Dorr, P. M.; Taber, J. J.; McQuillan, P.; Busby, R. W.; Woodward, R.

2013-12-01

USArray has engaged in a variety of activities that involve students in and inform the general public about EarthScope. Examples include the highly successful Transportable Array Student Siting Program that employed students and faculty from colleges and universities in the identification of sites for future Transportable Array stations in their region, and a range of informal education and media opportunities where information about EarthScope and its discoveries are shared with educators and the public. During the course of eight summers, more than 135 students from about 55 institutions conducted site reconnaissance for nearly 1375 sites from the West Coast to the East Coast, and from the Gulf of Mexico to the Great Lakes and southern Canada. While telling the EarthScope story, students who participated in the program increased their professional skills and deepened their personal growth. Other students had opportunities to engage in EarthScope-related research as part of the Research Experiences for Undergraduates program. Several EarthScope-focused outreach products for the public and educational audiences have been developed including Ground Motion Visualizations, EarthScope-centric and regional content sets for the IRIS Active Earth Monitor (AEM), and animations of earth processes. A kiosk loan program has helped to broadly disseminate the AEM displays. There have also been articles published in university, local and regional newspapers; stories appearing in national and international print and broadcast media; and documentaries produced by some of the world's most respected scientific and educational production companies that have included a segment about EarthScope and the Transportable Array. Over the next five years, USArray will be deploying and operating Transportable Array stations in Alaska and western Canada. This challenging environment will offer new opportunities to connect with communities throughout the region including native populations.

Opportunities Analysis of Potential Advanced Vortex Systems Separation Standards,

DTIC Science & Technology

1979-07-01

IAH 32 16 42 10 48 13 28 11 CLE 33 11 45 11 33 14 38 15 SEA 22 23 36 19 25 27 27 21 B-2 TABLE B-2 1985 IFR CAPACITIES IN OPERATIONS PER HOUR 20...18 53 23 EWR 7 23 54 16 9 28 44 19 IAN 7 22 50 13 8 24 49 19 CLE 5 16 64 15 6 20 53 21 4 SEA 9 27 42 22 11 32 32 25 C-2 TABLE C-2 1985 IFR CAPACITIES...Administration Office of Systems Engineering Management 14. SposoingAg, Cede Washington, DC 20591 AEM- 100 15. Supplementary Notes 16 . Abstract The

From the Lab to the real world : sources of error in UF {sub 6} gas enrichment monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lombardi, Marcie L.

2012-03-01

Safeguarding uranium enrichment facilities is a serious concern for the International Atomic Energy Agency (IAEA). Safeguards methods have changed over the years, most recently switching to an improved safeguards model that calls for new technologies to help keep up with the increasing size and complexity of today’s gas centrifuge enrichment plants (GCEPs). One of the primary goals of the IAEA is to detect the production of uranium at levels greater than those an enrichment facility may have declared. In order to accomplish this goal, new enrichment monitors need to be as accurate as possible. This dissertation will look at themore » Advanced Enrichment Monitor (AEM), a new enrichment monitor designed at Los Alamos National Laboratory. Specifically explored are various factors that could potentially contribute to errors in a final enrichment determination delivered by the AEM. There are many factors that can cause errors in the determination of uranium hexafluoride (UF{sub 6}) gas enrichment, especially during the period when the enrichment is being measured in an operating GCEP. To measure enrichment using the AEM, a passive 186-keV (kiloelectronvolt) measurement is used to determine the {sup 235}U content in the gas, and a transmission measurement or a gas pressure reading is used to determine the total uranium content. A transmission spectrum is generated using an x-ray tube and a “notch” filter. In this dissertation, changes that could occur in the detection efficiency and the transmission errors that could result from variations in pipe-wall thickness will be explored. Additional factors that could contribute to errors in enrichment measurement will also be examined, including changes in the gas pressure, ambient and UF{sub 6} temperature, instrumental errors, and the effects of uranium deposits on the inside of the pipe walls will be considered. The sensitivity of the enrichment calculation to these various parameters will then be evaluated. Previously, UF{sub 6} gas enrichment monitors have required empty pipe measurements to accurately determine the pipe attenuation (the pipe attenuation is typically much larger than the attenuation in the gas). This dissertation reports on a method for determining the thickness of a pipe in a GCEP when obtaining an empty pipe measurement may not be feasible. This dissertation studies each of the components that may add to the final error in the enrichment measurement, and the factors that were taken into account to mitigate these issues are also detailed and tested. The use of an x-ray generator as a transmission source and the attending stability issues are addressed. Both analytical calculations and experimental measurements have been used. For completeness, some real-world analysis results from the URENCO Capenhurst enrichment plant have been included, where the final enrichment error has remained well below 1% for approximately two months.« less

Tuning of platinum nano-particles by Au usage in their binary alloy for direct ethanol fuel cell: Controlled synthesis, electrode kinetics and mechanistic interpretation

NASA Astrophysics Data System (ADS)

Dutta, Abhijit; Mondal, Achintya; Datta, Jayati

2015-06-01

Understanding of the electrode-kinetics and mechanism of ethanol oxidation reaction (EOR) is of considerable interest for optimizing electro-catalysis in direct ethanol fuel cell (DEFC). This work attempts to design Pt based electro-catalyst on carbon support, tuned with gold nano-particles (NPs), for their use in DEFC operating in alkaline medium. The platinum-gold alloyed NPs are synthesized at desired compositions and size (2-10 nm) by controlled borohydride reduction method and successfully characterized by XRD, TEM, EDS and XPS techniques. The kinetic parameters along with the activation energies for the EOR are evaluated over the temperature range 20-80 °C and the oxidation reaction products estimated through ion chromatographic analysis. Compared to single Pt/C catalyst, the over potential of EOR is reduced by ca. 500 mV, at the onset during the reaction, for PtAu/C alloy with only 23% Pt content demonstrating the ability of Au and/or its surface oxides providing oxygen species at much lower potentials compared to Pt. Furthermore, a considerable increase in the peak power density (>191%) is observed in an in-house fabricated direct ethanol anion exchange membrane fuel cell, DE(AEM)FC using the best performing Au covered Pt electrode (23% Pt) compared to the monometallic Pt catalyst.

Consensus-based Recommendations for Research Priorities Related to Interventions to Safeguard Patient Safety in the Crowded Emergency Department

PubMed Central

Fee, Christopher; Hall, Kendall; Morrison, J. Bradley; Stephens, Robert; Cosby, Karen; Fairbanks, Rollin (Terry) J.; Youngberg, Barbara; Lenehan, Gail; Abualenain, Jameel; O’Connor, Kevin; Wears, Robert

2012-01-01

This article describes the results of the Interventions to Safeguard Safety breakout session of the 2011 Academic Emergency Medicine (AEM) consensus conference entitled “Interventions to Assure Quality in the Crowded Emergency Department.” Using a multistep nominal group technique, experts in emergency department (ED) crowding, patient safety, and systems engineering defined knowledge gaps and priority research questions related to the maintenance of safety in the crowded ED. Consensus was reached for seven research priorities related to interventions to maintain safety in the setting of a crowded ED. Included among these are: 1) How do routine corrective processes and compensating mechanism change during crowding? 2) What metrics should be used to determine ED safety? 3) How can checklists ensure safer care and what factors contribute to their success or failure? 4) What constitutes safe staffing levels / ratios? 5) How can we align emergency medicine (EM)-specific patient safety issues with national patient safety issues? 6) How can we develop metrics and skills to recognize when an ED is getting close to catastrophic overload conditions? and 7) What can EM learn from experts and modeling from fields outside of medicine to develop innovative solutions? These priorities have the potential to inform future clinical and human factors research and extramural funding decisions related to this important topic. PMID:22168192

Automated thin-film analyses of anhydrous interplanetary dust particles in the analytical electron microscope

NASA Technical Reports Server (NTRS)

Bradley, J. P.; Germani, M. S.; Brownlee, D. E.

1989-01-01

An AEM apparatus equipped with digital beam control has obtained quantitative point-count analyses of thin sections taken from eight anhydrous chondritic interplanetary dust particles (IDPs); between 200 and 500 X-ray analyses were collected from each thin section and analyzed for Mg, Al, Si, S, Ca, Cr, Mn, Fe, and Ni. Two types of anhydrous chondritic aggregates were observed in the eight IDPs: one highly porous, the other less so. The eight anhydrous IDPs are characterizable as mixtures of fine- and coarse-grained aggregates, large mineral grains, glass, and carbonaceous materials. Their elemental concentrations follow those of solar abundances, suggesting that they are unperturbed by aqueous alteration.

Mineralogy and Microstructures of Shock-Induced Melt Veins in Chondrites

NASA Technical Reports Server (NTRS)

Sharp, Thomas G.

2000-01-01

The applicability of phase equilibrium data to the interpretation of shock-induced melt veins can only be tested by a detailed study of melt- vein mineralogy to see how high-pressure assemblages vary as a function of shock conditions inferred from other indicators. We have used transmission electron microscopy (TEM), analytical electron microscopy (AEM), scanning electron microscopy (SEM), electron microprobe analysis (EMA) and optical petrography to characterize the mineralogy, microstructures, and compositions of melt veins and associated high-pressure minerals in shocked chondrites and SNC meteorites. In the processes, we have gained a better understanding of what melt veining can tell us about shock conditions and we have discovered new mineral phases in chondritic and SNC meteorites.

Medical education research in the context of translational science.

PubMed

Santen, Sally A; Deiorio, Nicole M; Gruppen, Larry D

2012-12-01

Health care struggles to transfer recent discoveries into high-quality medical care. Therefore, translational science seeks to improve the health of patients and communities by studying and promoting the translation of findings from bench research into clinical care. Similarly, medical education practice may be slow to adopt proven evidence of better learning and assessment. The Academic Emergency Medicine (AEM) consensus conference was designed to promote the dissemination of evidence-based education research and practice. We will pull from the work developed by the consensus conference as a means to create a roadmap for future medical education research using the framework of translational science. © 2012 by the Society for Academic Emergency Medicine.

Regional scale groundwater resource assessment in the Australian outback - Geophysics is the only way.

NASA Astrophysics Data System (ADS)

Munday, T. J.; Davis, A. C.; Gilfedder, M.; Annetts, D.

2015-12-01

Resource development, whether in agriculture, mining and/or energy, is set to have significant consequences for the groundwater resources of Australia in the short to medium term. These industry sectors are of significant economic value to the country and consequently their support remains a priority for State and Federal Governments alike. The scale of potential developments facilitated in large part by the Government Programs, like the West Australian (WA) Government's "Water for Food" program, and the South Australian's Government's PACE program, will result in an increase in infrastructure requirements, including access to water resources and Aboriginal lands to support these developments. However, the increased demand for water, particularly groundwater, is likely to be compromised by the limited information we have about these resources. This is particularly so for remote parts of the country which are targeted as primary development areas. There is a recognised need to expand this knowledge so that water availability is not a limiting factor to development. Governments of all persuasions have therefore adopted geophysical technologies, particularly airborne electromagnetics (AEM), as a basis for extending the hydrogeological knowledge of data poor areas. In WA, the State Government has employed regional-scale AEM surveys as a basis for defining groundwater resources to support mining, regional agricultural developments whilst aiming to safeguard regional population centres, and environmental assets. A similar approach is being employed in South Australia. These surveys are being used to underpin conceptual hydrogeological frameworks, define basin-scale hydrogeological models, delimit the extent of saltwater intrusion in coastal areas, and to determine the groundwater resource potential of remote alluvial systems aimed at supporting new, irrigation-based, agricultural developments in arid parts of the Australian outback. In the absence of conventional hydrogeological information, geophysical methods are demonstrably a cost and time effective approach to upscaling local hydrogeological information, thereby fast tracking groundwater resource assessments that would otherwise take decades to complete.

Non-Platinum Group Metal OER/ORR Catalysts for Alkaline Membrane Fuel Cells and Electrolyzers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Danilovic, Nemanja; Ayers, Katherine

Regenerative fuel cells (RFC) are energy storage devices that capture electrical energy in the form of hydrogen, with potential application for backup power and energy storage in remote locations, unmanned missions, and renewable energy capture. A unitized regenerative fuel cell (URFC) combines two separate electrochemical devices (fuel cell and electrolyzer) into one stack. The stack cost is driven by the platinum group metal (PGM) catalysts and the flow field components designed to withstand high potentials in acidic environments. Since the stack is the most expensive subcomponent of both the fuel cell and electrolyzer system, combining the two devices results inmore » substantial reduction in capital cost. However, in the past, combining the two stacks sacrificed device performance (operating cost) largely because the fuel cell had to operate with the thick electrolysis membranes in a URFC configuration, and due to water management issues in switching modes. Recent work in membrane-based electrolysis has resulted in more mechanically robust designs and materials that allow much thinner membranes, and work in flow cell design such as flow batteries has shown improved water transport through channel design and wet-proofing approaches. Therefore, the URFC concept is worth revisiting. At the same time, alkaline exchange membrane (AEM) devices are gathering attention due to the promise of PGM and valve metal elimination from the stack and a resulting strategic and capital cost benefit as compared with proton exchange membrane (PEM) systems. The result is a lower capital cost system that has half the precious metal group (PGM) catalysts, membrane and other stack component materials compared with discrete RFCs, although at the sacrifice of performance (operating cost). Proton has identified innovative AEM based RFC's to fulfill the role of low capital cost energy storage device owing to the use of non-precious metal containing electrodes, that enables certain markets where higher operating costs can be tolerated.« less

Delineation of a shallow subsurface aquiclude relief with aero electromagnetic data

NASA Astrophysics Data System (ADS)

Römer, A.; Winkler, E.; Bieber, G.; Motschka, K.; Reitner, H.

2009-04-01

Within a governmental groundwater remediation project in Austria, a new (overworked) characterization of a large catchment area (600 km2) with aeroelectromagnetics (AEM) was carried out. This catchment area is a large and important zone of subsurface water resources for currently and future municipal and rural water supply. Conflicts in future land use between e.g. agricultura, excavigation of mass materials, city and regional planning, ect. are preassigned and have impacts concerning the quality and quantity of available groundwater. The geology of the investigation area is a typical post-glacial region, characterized by aggradational deposition areas. The thickness of the wide-spread terrace gravels ranges from 10m to 40m, being the preferred ground water aquifer. The subsurface of the investigation area is built up by a Neogen basement, the so called Molasse and is acting as an aquiclude relative to the overlying quaternary sediments. Aeroelectromagnetic data from a former aerogeophysical survey were reinterpreted with a new processing and interpretation approach for the determination of this geological 3 layer case. This aeroelectromagnetic inversion integrates results from borehole data, ground geoelectric surveys and from geological mapping as a priori input information. The inversion result for a measured AEM data value is determined by a combination of geostatistically weighted additional information and likelihood weighted theoretical models. The primary aim of the study was the delineation of the aquiclude relief. The ground water circulation within the different terrace gravels is substantially affected by this Neogen relief. Depressions and prequaternary (tertiary) riverbeds within the Molasse often show other trends of water flow than the surficial, recent vales. The knowledge of the hydrogeological framework is essential for identification and definition of water protection and catchment areas as a decision base for national land use regulations. The result is a topographic model of the aquiclude with a depth resolution of ±5m.

Particulate Organic Matter Distribution along the Lower Amazon River: Addressing Aquatic Ecology Concepts Using Fatty Acids

PubMed Central

Mortillaro, Jean-Michel; Rigal, François; Rybarczyk, Hervé; Bernardes, Marcelo; Abril, Gwenaël; Meziane, Tarik

2012-01-01

One of the greatest challenges in understanding the Amazon basin functioning is to ascertain the role played by floodplains in the organic matter (OM) cycle, crucial for a large spectrum of ecological mechanisms. Fatty acids (FAs) were combined with environmental descriptors and analyzed through multivariate and spatial tools (asymmetric eigenvector maps, AEM and principal coordinates of neighbor matrices, PCNM). This challenge allowed investigating the distribution of suspended particulate organic matter (SPOM), in order to trace its seasonal origin and quality, along a 800 km section of the Amazon river-floodplain system. Statistical analysis confirmed that large amounts of saturated FAs (15:0, 18:0, 24:0, 25:0 and 26:0), an indication of refractory OM, were concomitantly recorded with high pCO2 in rivers, during the high water season (HW). Contrastingly, FAs marker which may be attributed in this ecosystem to aquatic plants (18:2ω6 and 18:3ω3) and cyanobacteria (16:1ω7), were correlated with higher O2, chlorophyll a and pheopigments in floodplains, due to a high primary production during low waters (LW). Decreasing concentrations of unsaturated FAs, that characterize labile OM, were recorded during HW, from upstream to downstream. Furthermore, using PCNM and AEM spatial methods, FAs compositions of SPOM displayed an upstream-downstream gradient during HW, which was attributed to OM retention and the extent of flooded forest in floodplains. Discrimination of OM quality between the Amazon River and floodplains corroborate higher autotrophic production in the latter and transfer of OM to rivers at LW season. Together, these gradients demonstrate the validity of FAs as predictors of spatial and temporal changes in OM quality. These spatial and temporal trends are explained by 1) downstream change in landscape morphology as predicted by the River Continuum Concept; 2) enhanced primary production during LW when the water level decreased and its residence time increased as predicted by the Flood Pulse Concept. PMID:23029412

Efficient Geological Modelling of Large AEM Surveys

NASA Astrophysics Data System (ADS)

Bach, Torben; Martlev Pallesen, Tom; Jørgensen, Flemming; Lundh Gulbrandsen, Mats; Mejer Hansen, Thomas

2014-05-01

Combining geological expert knowledge with geophysical observations into a final 3D geological model is, in most cases, not a straight forward process. It typically involves many types of data and requires both an understanding of the data and the geological target. When dealing with very large areas, such as modelling of large AEM surveys, the manual task for the geologist to correctly evaluate and properly utilise all the data available in the survey area, becomes overwhelming. In the ERGO project (Efficient High-Resolution Geological Modelling) we address these issues and propose a new modelling methodology enabling fast and consistent modelling of very large areas. The vision of the project is to build a user friendly expert system that enables the combination of very large amounts of geological and geophysical data with geological expert knowledge. This is done in an "auto-pilot" type functionality, named Smart Interpretation, designed to aid the geologist in the interpretation process. The core of the expert system is a statistical model that describes the relation between data and geological interpretation made by a geological expert. This facilitates fast and consistent modelling of very large areas. It will enable the construction of models with high resolution as the system will "learn" the geology of an area directly from interpretations made by a geological expert, and instantly apply it to all hard data in the survey area, ensuring the utilisation of all the data available in the geological model. Another feature is that the statistical model the system creates for one area can be used in another area with similar data and geology. This feature can be useful as an aid to an untrained geologist to build a geological model, guided by the experienced geologist way of interpretation, as quantified by the expert system in the core statistical model. In this project presentation we provide some examples of the problems we are aiming to address in the project, and show some preliminary results.

Structural Mapping Along the Central San Andreas Fault-zone Using Airborne Electromagnetics

NASA Astrophysics Data System (ADS)

Zamudio, K. D.; Bedrosian, P.; Ball, L. B.

2017-12-01

Investigations of active fault zones typically focus on either surface expressions or the associated seismogenic zones. However, the largely aseismic upper kilometer can hold significant insight into fault-zone architecture, strain partitioning, and fault-zone permeability. Geophysical imaging of the first kilometer provides a link between surface fault mapping and seismically-defined fault zones and is particularly important in geologically complex regions with limited surface exposure. Additionally, near surface imaging can provide insight into the impact of faulting on the hydrogeology of the critical zone. Airborne electromagnetic (AEM) methods offer a unique opportunity to collect a spatially-large, detailed dataset in a matter of days, and are used to constrain subsurface resistivity to depths of 500 meters or more. We present initial results from an AEM survey flown over a 60 kilometer long segment of the central San Andreas Fault (SAF). The survey is centered near Parkfield, California, the site of the SAFOD drillhole, which marks the transition between a creeping fault segment to the north and a locked zone to the south. Cross sections with a depth of investigation up to approximately 500 meters highlight the complex Tertiary and Mesozoic geology that is dismembered by the SAF system. Numerous fault-parallel structures are imaged across a more than 10 kilometer wide zone centered on the surface trace. Many of these features can be related to faults and folds within Plio-Miocene sedimentary rocks found on both sides of the fault. Northeast of the fault, rocks of the Mesozoic Franciscan and Great Valley complexes are extremely heterogeneous, with highly resistive volcanic rocks within a more conductive background. The upper 300 meters of a prominent fault-zone conductor, previously imaged to 1-3 kilometers depth by magnetotellurics, is restricted to a 20 kilometer long segment of the fault, but is up to 4 kilometers wide in places. Elevated fault-zone conductivity may be related to damage within the fault zone, Miocene marine shales, or some combination of the two.

Full-length genome sequence of a simian immunodeficiency virus (SIV) infecting a captive agile mangabey (Cercocebus agilis) is closely related to SIVrcm infecting wild red-capped mangabeys (Cercocebus torquatus) in Cameroon.

PubMed

Ahuka-Mundeke, Steve; Liegeois, Florian; Ayouba, Ahidjo; Foupouapouognini, Yacouba; Nerrienet, Eric; Delaporte, Eric; Peeters, Martine

2010-12-01

Simian immunodeficiency viruses (SIVs) are lentiviruses that infect an extensive number of wild African primate species. Here we describe for the first time SIV infection in a captive agile mangabey (Cercocebus agilis) from Cameroon. Phylogenetic analysis of the full-length genome sequence of SIVagi-00CM312 showed that this novel virus fell into the SIVrcm lineage and was most closely related to a newly characterized SIVrcm strain (SIVrcm-02CM8081) from a wild-caught red-capped mangabey (Cercocebus torquatus) from Cameroon. In contrast to red-capped mangabeys, no 24 bp deletion in CCR5 has been observed in the agile mangabey. Further studies on wild agile mangabeys are needed to determine whether agile and red-capped mangabeys are naturally infected with the same SIV lineage, or whether this agile mangabey became infected with an SIVrcm strain in captivity. However, our study shows that agile mangabeys are susceptible to SIV infection.

Heat Transfer Effects on Laminar Velocity Profiles in Pipe Flow

NASA Astrophysics Data System (ADS)

Powell, Robert; Jenkins, Thomas

1998-11-01

Heat Transfer Effects on Laminar Velocity Profiles in Pipe Flow. Robert L. Powell, Thomas P. Jenkins Department of Chemical Engineering & Materials Science University of California, Davis, CA 95616 Using laser Doppler velocimetry, we have measured the axial velocity profiles for steady, pressure driven, laminar flow of water in a circular tube. The flow was established in a one inch diameter seamless glass tube. The entry length prior to the measuring section was over one hundred diameters. Reynolds numbers in the range 500-2000 were used. Under conditions where the temperature difference between the fluid and the surroundings differed by as little as 0.2C, we found significant asymmetries in the velocity profiles. This asymmetry was most pronounced in the vertical plane. Varying the temperature difference moved the velocity maximum either above or below the centerline depending upon whether the fluid was warmer or cooler than the room. These results compare well to existing calculations. Using the available theory and our experiments it is possible to identify parameter ranges where non-ideal conditions(not parabolic velocity profiles) will be found. Supported by the EMSP Program of DOE.

Improving Conceptual Models Using AEM Data and Probability Distributions

NASA Astrophysics Data System (ADS)

Davis, A. C.; Munday, T. J.; Christensen, N. B.

2012-12-01

With emphasis being placed on uncertainty in groundwater modelling and prediction, coupled with questions concerning the value of geophysical methods in hydrogeology, it is important to ask meaningful questions of hydrogeophysical data and inversion results. For example, to characterise aquifers using electromagnetic (EM) data, we ask questions such as "Given that the electrical conductivity of aquifer 'A' is less than x, where is that aquifer elsewhere in the survey area?" The answer may be given by examining inversion models, selecting locations and layers that satisfy the condition 'conductivity <= x', and labelling them as aquifer 'A'. One difficulty with this approach is that the inversion model result often be considered to be the only model for the data. In reality it is just one image of the subsurface that, given the method and the regularisation imposed in the inversion, agrees with measured data within a given error bound. We have no idea whether the final model realised by the inversion satisfies the global minimum error, or whether it is simply in a local minimum. There is a distribution of inversion models that satisfy the error tolerance condition: the final model is not the only one, nor is it necessarily the correct one. AEM inversions are often linearised in the calculation of the parameter sensitivity: we rely on the second derivatives in the Taylor expansion, thus the minimum model has all layer parameters distributed about their mean parameter value with well-defined variance. We investigate the validity of the minimum model, and its uncertainty, by examining the full posterior covariance matrix. We ask questions of the minimum model, and answer them in a probabilistically. The simplest question we can pose is "What is the probability that all layer resistivity values are <= a cut-off value?" We can calculate through use of the erf or the erfc functions. The covariance values of the inversion become marginalised in the integration: only the main diagonal is used. Complications arise when we ask more specific questions, such as "What is the probability that the resistivity of layer 2 <= x, given that layer 1 <= y?" The probability then becomes conditional, calculation includes covariance terms, the integration is taken over many dimensions, and the cross-correlation of parameters becomes important. To illustrate, we examine the inversion results of a Tempest AEM survey over the Uley Basin aquifers in the Eyre Peninsula, South Australia. Key aquifers include the unconfined Bridgewater Formation that overlies the Uley and Wanilla Formations, which contain Tertiary clays and Tertiary sandstone. These Formations overlie weathered basement which define the lower bound of the Uley Basin aquifer systems. By correlating the conductivity of the sub-surface Formation types, we pose questions such as: "What is the probability-depth of the Bridgewater Formation in the Uley South Basin?", "What is the thickness of the Uley Formation?" and "What is the most probable depth to basement?" We use these questions to generate improved conceptual hydrogeological models of the Uley Basin in order to develop better estimates of aquifer extent and the available groundwater resource.

Satellite global monitoring of environmental quality

NASA Technical Reports Server (NTRS)

Schiffer, R. A.

1975-01-01

The missions of two NASA satellites for the monitoring of environmental quality are described: Nimbus G, the Air Pollution and Oceanographic Observing Satellite, and the Applications Explorer Mission (AEM) satellite to be used in the Stratospheric Aerosol and Gas Experiment (SAGE). The scientific payload of Nimbus G is described in detail with a discussion of limb infrared monitoring of the stratosphere, the stratospheric and mesospheric sounder, stratospheric aerosol measurement, the solar and backscatter UV spectrometer for ozone mapping, the earth radiation budget experiment, the scanning multichannel microwave radiometer, the coastal zone color scanner and the temperature-humidity infrared radiometer. A brief description is given of the SAGE program and future NASA plans relating to the global monitoring of environmental quality are outlined.

Differential right ventricular regional function and the effect of pulmonary hypertension: three-dimensional echo study.

PubMed

Calcutteea, Avin; Chung, Robin; Lindqvist, Per; Hodson, Margaret; Henein, Michael Y

2011-06-01

The right ventricle is multicompartmental in orientation. To assess the normal differential function of the right ventricular (RV) inflow, apical and outflow compartments, also their inter-relations and the response to pulmonary arterial hypertension (PAH). 45 people were studied--16 controls and 29 patients with left-sided heart failure, 15 without (group 1) and 14 with (group 2) secondary PAH, using two-dimensional (2D) and 3D echocardiography in addition to conventional Doppler techniques. There was a strong correlation between RV inlet diameter (2D) and end-diastolic volume (3D) (r=0.69, p<0.001) and between tricuspid annular plane systolic excursion and RV ejection fraction (3D) (r=0.71, p<0.001). In controls and patients, the apical ejection fraction was less than the inflow and outflow (controls: p<0.01 and p<0.01, group 1: p<0.05 and p<0.01 and group 2: p<0.05 and p<0.01, respectively). Ejection fraction was reduced in patients (inflow: p<0.001 for both, apical: p<0.01 for both and outflow tract: p<0.05 for both). In controls, the inflow compartment reached the minimum volume 20 ms before the outflow and apex but in group 2 it was simultaneous. Isovolumic contraction and relaxation times were prolonged in patients (Group 1: p=0.02 and p<0.01 and Group 2: p=0.01 for both). Peak RV ejection time correlated with the rate of outflow volume fall in controls but with the apex in group 2 (r=0.6, p<0.05). The right ventricle has distinct features for the inflow, apical and outflow tract compartments, with different extent of contribution to the overall systolic function. In PAH, the right ventricle becomes one dyssynchronous compartment, which itself may have perpetual effect on overall cardiac dysfunction.

NASA Animal Enclosure Module Mouse Odor Containment Study for STS-107 September 15, 1999;SJSU Odor Panel Data

NASA Technical Reports Server (NTRS)

Holley, Daniel C.; Mele, Gary D.; Poffenroth, Mary; Young, Cliff

2000-01-01

Experiment #153 by Scott Brady is manifested for shuttle flight STS-107. This evaluation of space flight induced stress and its effects on neuronal plasticity will use 18 six month old C57Bl/6 male mice. A 21 day evaluation study was proposed to determine the length of time groups of 6, 9, or 12 mice could be housed in the Animal Enclosure Module (AEM) without odor breakthrough. This study was performed at NASA-Ames Research Center beginning on September 15, 1999. NASA personnel, were responsible for animal care, maintenance, facilities, hardware, etc. San Jose State personnel performed the odor panel evaluations and data reduction. We used similar procedures and methods for earlier tests evaluating female mice.

Imidazolium Cations with Exceptional Alkaline Stability: A Systematic Study of Structure–Stability Relationships

DOE PAGES

Hugar, Kristina M.; Kostalik, IV, Henry A.; Coates, Geoffrey W.

2015-06-11

Highly base-stable cationic moieties are a critical component of anion exchange membranes (AEMs) in alkaline fuel cells (AFCs); however, the commonly employed organic cations have limited alkaline stability. To address this problem, we synthesized and characterized the stability of a series of imidazolium cations in 1, 2, or 5 M KOH/CD 3OH at 80 °C, systematically evaluating the impact of substitution on chemical stability. The substituent identity at each position of the imidazolium ring has a dramatic effect on the overall cation stability. In conclusion, we report imidazolium cations that have the highest alkaline stabilities reported to date, >99% cationmore » remaining after 30 days in 5 M KOH/CD 3OH at 80 °C.« less

Phase 3 geophysical studies in the Wadi Bidah District, Kingdom of Saudi Arabia

USGS Publications Warehouse

Flanigan, V.J.; Sadek, Hamdy; Smith, C.W.

1982-01-01

Detailed geophysical measurements have been made in the Rabathan area, Wadi Bidah district, Kingdom of Saudi Arabia, at the site of diamond drill holes RAB-1, -2, and -3; these measurements suggest that the causative source for the anomalous EM (electromagnetic) and SP (self-potential) responses is probably highly conductive zones of Precambrian siliceous-carbonaceous rocks. Although many of the zones are no more than a few meters wide, they commonly contain 50 to 80 percent carbonaceous material and locally abundant pyrite. In places, several thin layers of highly concentrated carbonaceous material interlayered with chert form a multiple conductive zone that is seen in the geophysical data as complex anomaly patterns. In the geologic environment of Wadi Bidah, massive sulfide-bearing zones cannot be distinguished from siliceous-carbonaceous zones on the basis of the EM-SP responses. In North America in similar environments, complex resistivity methods used in experimental research have successfully discriminated between sulfide and carbonaceous conductors. Tests of such methods in the Wadi Bidah district are recommended. Geologic, geochemical, and geophysical data at the Jabal Mohr prospect suggest the possibility of mineralized rocks at depth over a possible strike length of 400 m.

Vertical profiles reveal impact of ozone and temperature on carbon assimilation of Betula pendula and Populus tremula.

PubMed

Mäenpää, Maarit; Riikonen, Johanna; Kontunen-Soppela, Sari; Rousi, Matti; Oksanen, Elina

2011-08-01

Rising temperature and tropospheric ozone (O(3)) concentrations are likely to affect carbon assimilation processes and thus the carbon sink strength of trees. In this study, we investigated the joint action of elevated ozone and temperature on silver birch (Betula pendula) and European aspen (Populus tremula) saplings in field conditions by combining free-air ozone exposure (1.2 × ambient) and infrared heaters (ambient +1.2 °C). At leaf level measurements, elevated ozone decreased leaf net photosynthesis (P(n)), while the response to elevated temperature was dependent on leaf position within the foliage. This indicates that leaf position has to be taken into account when leaf level data are collected and applied. The ozone effect on P(n) was partly compensated for at elevated temperature, showing an interactive effect of the treatments. In addition, the ratio of photosynthesis to stomatal conductance (P(n)/g(s) ratio) was decreased by ozone, which suggests decreasing water use efficiency. At the plant level, the increasing leaf area at elevated temperature resulted in a considerable increase in photosynthesis and growth in both species.

Arsenic treatment and power generation with a dual-chambered fuel cell with anionic and cationic membranes using NaHCO3 anolyte and HCl or NaCl catholyte.

PubMed

Maitlo, Hubdar Ali; Kim, Jung Hwan; Park, Joo Yang

2017-04-01

Dual-chambered fuel cells with an iron anode and an air-carbon cathode separated by an ion exchange membranes have been used to treat arsenate during power production. To select an effective catholyte, the dual-chambered fuel cell consisted 90 mL of 0.1 M HCl or 0.5 M NaCl as the catholyte and 1 L of 0.1 M NaHCO 3 as the anolyte at an initial pH 5. The 0.1 M HCl was an effective catholyte, with which 1 ppm arsenate in 1 L of anolyte was reduced to 5 ppb in 1 h, and the maximum power density was about 6.3 w/m 2 with an anion exchange membrane fuel cell (AEM_FC) and 4.4 w/m 2 with a cation exchange membrane fuel cell (CEM_FC). Therefore, 90 mL of 0.1 M HCl was used as a catholyte to treat 20 L of 0.1 M NaHCO 3 anolyte containing 1 ppm arsenate at an initial pH of 5 or 7. The arsenate level at pH 5 decreased to less than 5 ppb in 4 h, and the maximum power density was 5.9 W/m 2 and 4.7 W/m 2 with AEM_FC and CEM_FC, respectively. When using 0.01 M NaHCO 3 as the anolyte at pH 5, arsenate was reduced to less than 5 ppb in 8 and 24 h for AEC_FC and CEM_FC, respectively. However, when using an anolyte at pH 7, arsenate could not be effectively removed in 24 h. Therefore, when using carbonate as an anolyte, the solution should be adjusted to a weakly acidic pH in order to remove arsenate. Copyright © 2017 Elsevier Ltd. All rights reserved.

EM Diffusion for a Time-Domain Airborne EM System

NASA Astrophysics Data System (ADS)

Yin, C.; Qiu, C.; Liu, Y.; Cai, J.

2014-12-01

Visualization of EM diffusion for an airborne EM (AEM) system is important for understanding the transient procedure of EM diffusion. The current distribution and diffusion features also provide effective means to evaluate EM footprint, depth of exploration and further help AEM system design and data interpretation. Most previous studies on EM diffusion (or "smoke ring" effect) are based on the static presentation of EM field, where the dynamic features of EM diffusion were not visible. For visualizing the dynamic feature of EM diffusion, we first calculate in this paper the frequency-domain EM field by downward continuation of the EM field at the EM receiver to the deep earth. After that, we transform the results to time-domain via a Fourier transform. We take a homogeneous half-space and a two-layered earth induced by a step pulse to calculate the EM fields and display the EM diffusion in the earth as 3D animated vectors or time-varying contours. The "smoke ring" effect of EM diffusion, dominated by the resistivity distribution of the earth, is clearly observed. The numerical results for an HCP (vertical magnetic dipole) and a VCX (horizontal magnetic dipole) transmitting coil above a homogeneous half-space of 100 ohm-m are shown in Fig.1. We display as example only the distribution of EM field inside the earth for the diffusion time of 0.05ms. The detailed EM diffusion will be shown in our future presentation. From the numerical experiments for different models, we find that 1) the current for either an HCP or a VCX transmitting dipole propagates downward and outward with time, becoming wider and more diffuse, forming a "smoke ring"; 2) for a VCX transmitter, the underground current forms two ellipses, corresponding to the two polarities of the magnetic flux of a horizontal magnetic dipole, injecting into or ejected from the earth; 3) for a HCP transmitter, however, the underground current forms only one circle, corresponding to the polarity of the magnetic flux for a vertical magnetic dipole, injecting into the earth; 4) there exists no vertical current in an isotropic homogeneous half-space. The currents for both HCP and VCX transmitting dipole flow horizontally.

LAMMPS framework for dynamic bonding and an application modeling DNA

NASA Astrophysics Data System (ADS)

Svaneborg, Carsten

2012-08-01

We have extended the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) to support directional bonds and dynamic bonding. The framework supports stochastic formation of new bonds, breakage of existing bonds, and conversion between bond types. Bond formation can be controlled to limit the maximal functionality of a bead with respect to various bond types. Concomitant with the bond dynamics, angular and dihedral interactions are dynamically introduced between newly connected triplets and quartets of beads, where the interaction type is determined from the local pattern of bead and bond types. When breaking bonds, all angular and dihedral interactions involving broken bonds are removed. The framework allows chemical reactions to be modeled, and use it to simulate a simplistic, coarse-grained DNA model. The resulting DNA dynamics illustrates the power of the present framework. Catalogue identifier: AEME_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEME_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: GNU General Public Licence No. of lines in distributed program, including test data, etc.: 2 243 491 No. of bytes in distributed program, including test data, etc.: 771 Distribution format: tar.gz Programming language: C++ Computer: Single and multiple core servers Operating system: Linux/Unix/Windows Has the code been vectorized or parallelized?: Yes. The code has been parallelized by the use of MPI directives. RAM: 1 Gb Classification: 16.11, 16.12 Nature of problem: Simulating coarse-grain models capable of chemistry e.g. DNA hybridization dynamics. Solution method: Extending LAMMPS to handle dynamic bonding and directional bonds. Unusual features: Allows bonds to be created and broken while angular and dihedral interactions are kept consistent. Additional comments: The distribution file for this program is approximately 36 Mbytes and therefore is not delivered directly when download or E-mail is requested. Instead an html file giving details of how the program can be obtained is sent. Running time: Hours to days. The examples provided in the distribution take just seconds to run.

An AEM-TEM study of weathering and diagenesis, Abert Lake, Oregon: II. Diagenetic modification of the sedimentary assemblage

USGS Publications Warehouse

Banfield, J.F.; Jones, B.F.; Veblen, D.R.

1991-01-01

This paper compares the mineralogy and chemistry of clay minerals in sediments from various depths and positions in Abert Lake and surrounding playa with those of the weathered materials entering the lake in order to reveal the nature and extent of post-depositional mineralogical modification. Analytical electron microscope (AEM) data from individual clay particles reveal that each sample is comprised of a highly inhomogeneous smectite assemblage. The thin clay flakes (commonly less than 10 nm wide) display a complete range in octahedral sheet compositions from nearly dioctahedral to nearly trioctahedral. The very abundant Mg-rich lake smectites with an estimated composition K0.29(Al0.23-Mg2.16Fe0.30)Si3.80Al0.20O10(OH)2 are not formed by weathering. This confirms the importance of diagenetic Mg uptake. Lattice-fringe imaging failed to reveal distinct brucite-like or vermiculite-like layers, suggesting that interstratifications of this type are rare or absent. Siliceous coatings on clay particles (identified by silica excess in smectite analyses) seem to favor topotactic overgrowth of stevensite rather than addition of brucite-like layers to the dioctahedral nuclei. The growth of K-stevensite dilutes the Al content of the crystal, and thus the increasing diagenetic modification reduces rather than supplements its illite component. Smectite compositions within individual samples were highly variable, yet source-related characteristics such as the abundance of Fe-rich smectite were apparent. Little evidence for systematic K or Mg enrichment with depth was identified in samples from depths of down to 16 feet below the sediment-water interface. The most magnesian assemblages are associated both with weathering sources of Mg-rich smectite and playa environments subjected to repeated wetting and drying cycles. Thus, the observations suggest that clay compositions primarily reflect changes in lake levels, brine composition, and source characteristics, rather than time and depth/compaction effects. Other diagenetic reactions in the sediment include recrystallization of Na-rich silica gel and diatom fragments. Abundant, submicron-sized, untwinned, euhedral crystals of K-feldspar are interpreted to be authigenic in origin. ?? 1991.

An interpretation of the 1997 airborne electromagnetic (AEM) survey, Fort Huachuca vicinity, Cochise County, Arizona

USGS Publications Warehouse

Bultman, Mark W.; Gettings, Mark E.; Wynn, Jeff

1999-01-01

In March of 1997, an airborne electromagnetic (AEM) survey of the Fort Huachuca Military Reservation and immediate surrounds was conducted. This survey was sponsored by the U.S. Army and contracted through the Geologic Division of the U.S. Geological Survey (USGS). Data were gathered by Geoterrex-Dighem Ltd. of Ottawa, Canada. The survey aircraft is surrounded by a coil through which a large current pulse is passed. This pulse induces currents in the Earth which are recorded by a set of three mutually perpendicular coils towed in a "bird" about 100 m behind and below the aircraft. The bird also records the Earth's magnetic field. The system samples the Earth response to the electromagnetic pulse about every 16 m along the aircraft flight path. For this survey, the bulk of the flightpaths were spaced about 400 m apart and oriented in a northeast-southwest direction extending from bedrock over the Huachuca Mountains to bedrock over the Tombstone Hills. A preliminary report on the unprocessed data collected in the field was delivered to the U.S. Army by USGS in July 1997 (USGS Open-File Report 97–457). The final data were delivered in March, 1998 by the contractor to USGS and thence to the U.S. Army. The present report represents the final interpretive report from USGS. The objectives of the survey were to: 1) define the structure of the San Pedro basin in the Sierra Vista-Fort Huachuca-Huachuca City area, including the depth and shape of the basin, and to delineate large faults that may be active within the basin fill and therefore important in the hydrologic regime; 2) define near surface and subsurface areas that contain a large volume fraction of silt and clay in the basin fill and which both reduce the volume of available storage for water and reduce the permeability of the aquifer; and 3) to evaluate the use of the time domain electromagnetic method in the southwest desert setting as a means of mapping depth to water.

Land subsidence in southwest Cyprus revealed from C-band radar interferometry

NASA Astrophysics Data System (ADS)

Michalis, Pantelis; Giourou, Anthi; Charalampopoulou, Betty; Li, Zhenhong; Li, Yongsheng

2014-08-01

Land subsidence is a major worldwide hazard, and causes many problems including: damage to public facilities such as bridges, roads, railways, electric power lines, underground pipes; damage to private and public buildings; and in some cases of low-lying land, can increase the risk of coastal flooding from storm surges and rising sea-levels. The island of Cyprus is famous for its complex geology, particularly in the southwest part of the island. Deposits of massive breccias (melange) are widely exposed in the Paphos District situated between the Troodos Mountains and the sea. These deposits are rich in clay minerals that are prone to landslide phenomena. With its global coverage and all-weather imaging capability, Interferometric SAR (InSAR) is revolutionizing our ability to image the Earth's surface and the evolution of its shape over time. In this paper, an advanced InSAR time series technique, InSAR TS + AEM, has been employed to analysed C-band ERS and Envisat data collected over southwest Cyprus during the period from 1992 to 2010. Our InSAR time series results suggest that: (1) a total number of 274,619 coherent pixels with a density of 46 points per squared km were detected in the area of interest; and (2) clear surface displacements can be observed in several areas. The combination of archived ESA SAR datasets allows a long record (~18 years) of historic deformation to be measured over a large region. Ultimately this should help inform land managers in assessing land subsidence and planning appropriate remedial measures.

Tracking groundwater discharge to a large river using tracers and geophysics.

PubMed

Harrington, Glenn A; Gardner, W Payton; Munday, Tim J

2014-01-01

Few studies have investigated large reaches of rivers in which multiple sources of groundwater are responsible for maintaining baseflow. This paper builds upon previous work undertaken along the Fitzroy River, one of the largest perennial river systems in north-western Australia. Synoptic regional-scale sampling of both river water and groundwater for a suite of environmental tracers ((4) He, (87) Sr/(86) Sr, (222) Rn and major ions), and subsequent modeling of tracer behavior in the river, has enabled definition and quantification of groundwater input from at least three different sources. We show unambiguous evidence of both shallow "local" groundwater, possibly recharged to alluvial aquifers beneath the adjacent floodplain during recent high-flow events, and old "regional" groundwater introduced via artesian flow from deep confined aquifers. We also invoke hyporheic exchange and either bank return flow or parafluvial flow to account for background (222) Rn activities and anomalous chloride trends along river reaches where there is no evidence of the local or regional groundwater inputs. Vertical conductivity sections acquired through an airborne electromagnetic (AEM) survey provide insights to the architecture of the aquifers associated with these sources and general groundwater quality characteristics. These data indicate fresh groundwater from about 300 m below ground preferentially discharging to the river, at locations consistent with those inferred from tracer data. The results demonstrate how sampling rivers for multiple environmental tracers of different types-including stable and radioactive isotopes, dissolved gases and major ions-can significantly improve conceptualization of groundwater-surface water interaction processes, particularly when coupled with geophysical techniques in complex hydrogeological settings. © 2013, National Ground Water Association.

Thin-sectioning and analysis of fine-grained meteoritic materials

NASA Technical Reports Server (NTRS)

Brooks, Donald A. (Editor); Bradley, John P.

1992-01-01

The overall theme of the work was the identification of the sources and formation/aggregation mechanisms of the various classes of interplanetary dust particles (IDP's) and to clarify the relationship between IDP's and conventional meteorites. IDP's are believed to be derived from a much broader range of parent bodies than conventional meteorites. Some of these parent bodies (e.g., comets) have escaped that post accretional processing that has affected the parent bodies of meteorites. Therefore, IDP's are likely to preserve a record of early solar system and possibly presolar grain forming reactions. Using analytical electron microscopy (AEM) and more recently micro-infrared (IR) microspectroscopy to examine ultramicrotomed thin sections, we have addressed the questions of IDP formation mechanisms, sources, and their relationship to conventional meteorites. The following sections describe specific findings resulting from these studies.

Composite membranes, methods of making same, and applications of same

DOEpatents

Pintauro, Peter N.; Park, Andrew; Ballengee, Jason

2016-05-24

In one aspect of the present invention, a method of fabricating a composite membrane includes: forming a first polymer solution from a first polymer and a second polymer solution from a second polymer, respectively, where the first polymer includes a charged polymer and the second polymer includes an uncharged polymer; electrospinning, separately and simultaneously, the first and second polymer solutions to form a dual fiber mat with first polymer fibers and second polymer fibers; and processing the dual fiber mat by softening and flowing one of the first or second polymer fibers to fill in the void space between the other of the first and second polymer fibers so as to form the composite membrane. In some embodiments, the composite membrane may be a proton exchange membrane (PEM) or an anion exchange membrane (AEM).

SAGE ground truth plan: Correlative measurements for the Stratospheric Aerosol and Gas Experiment (SAGE) on the AEM-B satellite

NASA Technical Reports Server (NTRS)

Russell, P. B. (Editor); Cunnold, D. M.; Grams, G. W.; Laver, J.; Mccormick, M. P.; Mcmaster, L. R.; Murcray, D. G.; Pepin, T. J.; Perry, T. W.; Planet, W. G.

1979-01-01

The ground truth plan is outlined for correlative measurements to validate the Stratospheric Aerosol and Gas Experiment (SAGE) sensor data. SAGE will fly aboard the Applications Explorer Mission-B satellite scheduled for launch in early 1979 and measure stratospheric vertical profiles of aerosol, ozone, nitrogen dioxide, and molecular extinction between 79 N and 79 S. latitude. The plan gives details of the location and times for the simultaneous satellite/correlative measurements for the nominal launch time, the rationale and choice of the correlative sensors, their characteristics and expected accuracies, and the conversion of their data to extinction profiles. In addition, an overview of the SAGE expected instrument performance and data inversion results are presented. Various atmospheric models representative of stratospheric aerosols and ozone are used in the SAGE and correlative sensor analyses.

Animal Enclosure Module (AEM)

NASA Technical Reports Server (NTRS)

1998-01-01

The primary objective of this research project is to test the hypothesis that corticosteroids contribute to the adverse skeletal effects of space flight. To achieve this objective, serum corticosteroids, which are known to increase during space flight, must be maintained at normal physiologic levels in flight rats by a combination of adrenalectomy and corticosteroid supplementation via implanted hormone pellets. Bone analyses in these animals will then be compared to those of intact flight rats that, based on past experience, will undergo corticosteroid excess and bone loss during space flight. The results will reveal whether maintaining serum corticosteroids at physiologic levels in flight rats affects the skeletal abnormalities that normally develop during space flight. A positive response to this question would indicate that the bone loss and decreased bone formation associated with space flight are mediated, at least in part, by corticosteroid excess.

Integration of structural health monitoring solutions onto commercial aircraft via the Federal Aviation Administration structural health monitoring research program

NASA Astrophysics Data System (ADS)

Swindell, Paul; Doyle, Jon; Roach, Dennis

2017-02-01

The Federal Aviation Administration (FAA) started a research program in structural health monitoring (SHM) in 2011. The program's goal was to understand the technical gaps of implementing SHM on commercial aircraft and the potential effects on FAA regulations and guidance. The program evolved into a demonstration program consisting of a team from Sandia National Labs Airworthiness Assurance NDI Center (AANC), the Boeing Corporation, Delta Air Lines, Structural Monitoring Systems (SMS), Anodyne Electronics Manufacturing Corp (AEM) and the FAA. This paper will discuss the program from the selection of the inspection problem, the SHM system (Comparative Vacuum Monitoring-CVM) that was selected as the inspection solution and the testing completed to provide sufficient data to gain the first approved use of an SHM system for routine maintenance on commercial US aircraft.

Achieving Continuous Anion Transport Domains Using Block Copolymers Containing Phosphonium Cations

DOE PAGES

Zhang, Wenxu; Liu, Ye; Jackson, Aaron C.; ...

2016-06-22

Triblock and diblock copolymers based on isoprene (Ip) and chloromethylstyrene (CMS) were synthesized in this paper by sequential polymerization using reversible addition–fragmentation chain transfer radical polymerization (RAFT). The block copolymers were quaternized with tris(2,4,6-trimethoxyphenyl)phosphine (Ar 3P) to prepare soluble ionomers. The ionomers were cast from chloroform to form anion exchange membranes (AEMs) with highly ordered morphologies. At low volume fractions of ionic blocks, the ionomers formed lamellar morphologies, while at moderate volume fractions (≥30% for triblock and ≥22% for diblock copolymers) hexagonal phases with an ionic matrix were observed. Ion conductivities were higher through the hexagonal phase matrix than inmore » the lamellar phases. Finally, promising chloride conductivities (20 mS/cm) were achieved at elevated temperatures and humidified conditions.« less

Charge transport in the electrospun nanofiber composite membrane's three-dimensional fibrous structure

NASA Astrophysics Data System (ADS)

DeGostin, Matthew B.; Peracchio, Aldo A.; Myles, Timothy D.; Cassenti, Brice N.; Chiu, Wilson K. S.

2016-03-01

In this paper, a Fiber Network (FN) ion transport model is developed to simulate the three-dimensional fibrous microstructural morphology that results from the electrospinning membrane fabrication process. This model is able to approximate fiber layering within a membrane as well as membrane swelling due to water uptake. The discrete random fiber networks representing membranes are converted to resistor networks and solved for current flow and ionic conductivity. Model predictions are validated by comparison with experimental conductivity data from electrospun anion exchange membranes (AEM) and proton exchange membranes (PEM) for fuel cells as well as existing theories. The model is capable of predicting in-plane and thru-plane conductivity and takes into account detailed membrane characteristics, such as volume fraction, fiber diameter, fiber conductivity, and membrane layering, and as such may be used as a tool for advanced electrode design.

Water uptake, ionic conductivity and swelling properties of anion-exchange membrane

NASA Astrophysics Data System (ADS)

Duan, Qiongjuan; Ge, Shanhai; Wang, Chao-Yang

2013-12-01

Water uptake, ionic conductivity and dimensional change of the anion-exchange membrane made by Tokuyama Corporation (A201 membrane) are investigated at different temperatures and water activities. Specifically, the amount of water taken up by membranes exposed to water vapor and membranes soaked in liquid water is determined. The water uptake of the A201 membrane increases with water content as well as temperature. In addition, water sorption data shows Schroeder's paradox for the AEMs investigated. The swelling properties of the A201 membrane exhibit improved dimensional stability compared with Nafion membrane. Water sorption of the A201 membrane occurs with a substantial negative excess volume of mixing. The threshold value of hydrophilic fraction in the A201 membrane for ionic conductivity is around 0.34, above which, the conductivity begins to rise quickly. This indicates that a change in the connectivity of the hydrophilic domains occurs when hydrophilic fraction approaches 0.34.

Poly(vinylbenzylchloride) Based Anion-Exchange Blend Membranes (AEBMs): Influence of PEG Additive on Conductivity and Stability

PubMed Central

Kerres, Jochen A.; Krieg, Henning M.

2017-01-01

In view of the many possible applications such as fuel cells and electrolysers, recent interest in novel anion exchange membranes (AEMs) has increased significantly. However, their low conductivity and chemical stability limits their current suitability. In this study, the synthesis and characterization of several three- and four-component anion exchange blend membranes (AEBMs) is described, where the compositions have been systematically varied to study the influence of the AEBM’s composition on the anion conductivities as well as chemical and thermal stabilities under strongly alkaline conditions. It was shown that the epoxide-functionalized poly(ethylene glycol)s that were introduced into the four-component AEBMs resulted in increased conductivity as well as a marked improvement in the stability of the AEBMs in an alkaline environment. In addition, the thermal stability of the novel AEBMs was excellent showing the suitability of these membranes for several electrochemical applications. PMID:28621717

Characterization of Technetium Speciation in Cast Stone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Um, Wooyong; Jung, Hun Bok; Wang, Guohui

2013-11-11

This report describes the results from laboratory tests performed at Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE) EM-31 Support Program (EMSP) subtask, “Production and Long-Term Performance of Low Temperature Waste Forms” to provide additional information on technetium (Tc) speciation characterization in the Cast Stone waste form. To support the use of Cast Stone as an alternative to vitrification for solidifying low-activity waste (LAW) and as the current baseline waste form for secondary waste streams at the Hanford Site, additional understanding of Tc speciation in Cast Stone is needed to predict the long-term Tc leachability frommore » Cast Stone and to meet the regulatory disposal-facility performance requirements for the Integrated Disposal Facility (IDF). Characterizations of the Tc speciation within the Cast Stone after leaching under various conditions provide insights into how the Tc is retained and released. The data generated by the laboratory tests described in this report provide both empirical and more scientific information to increase our understanding of Tc speciation in Cast Stone and its release mechanism under relevant leaching processes for the purpose of filling data gaps and to support the long-term risk and performance assessments of Cast Stone in the IDF at the Hanford Site.« less

Acoustic characteristics of simulated respiratory-induced vocal tremor.

PubMed

Lester, Rosemary A; Story, Brad H

2013-05-01

The purpose of this study was to investigate the relation of respiratory forced oscillation to the acoustic characteristics of vocal tremor. Acoustical analyses were performed to determine the characteristics of the intensity and fundamental frequency (F0) for speech samples obtained by Farinella, Hixon, Hoit, Story, and Jones (2006) using a respiratory forced oscillation paradigm with 5 healthy adult males to simulate vocal tremor involving respiratory pressure modulation. The analyzed conditions were sustained productions of /a/ with amplitudes of applied pressure of 0, 1, 2, and 4 cmH2O and a rate of 5 Hz. Forced oscillation of the respiratory system produced modulation of the intensity and F0 for all participants. Variability was observed between participants and conditions in the change in intensity and F0 per unit of pressure change, as well as in the mean intensity and F0. However, the extent of modulation of intensity and F0 generally increased as the applied pressure increased, as would be expected. These findings suggest that individuals develop idiosyncratic adaptations to pressure modulations, which are important to understanding aspects of variability in vocal tremor, and highlight the need to assess all components of the speech mechanism that may be directly or indirectly affected by tremor.

Tricuspid regurgitation: contemporary management of a neglected valvular lesion.

PubMed

Irwin, Richard Bruce; Luckie, Matthew; Khattar, Rajdeep S

2010-11-01

Right-sided cardiac valvular disease has traditionally been considered less clinically important than mitral or aortic valve pathology. However, detectable tricuspid regurgitation (TR) is common and recent data suggest that significant TR can lead to functional impairment and reduced survival, particularly in patients with concomitant left-sided valvular disease. The tricuspid valve is a complex anatomical structure and advances in three dimensional echocardiography and cardiac MRI have contributed to a greater understanding of tricuspid valve pathology. These imaging techniques are invaluable in determining the aetiology and severity of TR, and provide an assessment of right ventricular function and pulmonary artery pressure. TR is more prevalent in women and those with a history of myocardial infarction and heart failure. It also occurs in about 10% of patients with rheumatic heart disease. Chronic severe TR may have a prolonged clinical course culminating in the development of fatigue and poor exercise tolerance due to a reduced cardiac output. Approximately 90% of cases of TR are secondary to either pulmonary hypertension or intrinsic right ventricular pathology and about 10% are due to primary tricuspid valve disease. Primary causes such as Ebstein's anomaly, rheumatic disease, myxomatous changes, carcinoid syndrome, endomyocardial fibrosis, and degenerative disease have characteristic morphological features readily identifiable by echocardiography. Ascertaining an accurate right ventricular systolic pressure is important in separating primary from secondary causes as significant TR with a pressure <40 mm Hg implies intrinsic valve disease. Cardiac MRI may be indicated in those with inadequate echocardiographic images and is also the gold standard for the evaluation of right ventricular function and morphology. The assessment of leaflet morphology, annular dimensions, and pulmonary artery pressure are particularly important for determining subsequent management. Along with appropriate treatment of the underlying cause of TR and pulmonary hypertension, management guidelines indicate a move towards more aggressive treatment of TR. In those undergoing left-sided valve surgery, tricuspid valve repair is universally recommended in the presence of severe coexistent TR; in those with isolated severe TR, surgery is recommended in the presence of symptoms or progressive right ventricular dilatation or dysfunction.

Estimation of Arctic Sea Ice Freeboard and Thickness Using CryoSat-2

NASA Astrophysics Data System (ADS)

Lee, S.; Im, J.; Kim, J. W.; Kim, M.; Shin, M.

2014-12-01

Arctic sea ice is one of the significant components of the global climate system as it plays a significant role in driving global ocean circulation. Sea ice extent has constantly declined since 1980s. Arctic sea ice thickness has also been diminishing along with the decreasing sea ice extent. Because extent and thickness, two main characteristics of sea ice, are important indicators of the polar response to on-going climate change. Sea ice thickness has been measured with numerous field techniques such as surface drilling and deploying buoys. These techniques provide sparse and discontinuous data in spatiotemporal domain. Spaceborne radar and laser altimeters can overcome these limitations and have been used to estimate sea ice thickness. Ice Cloud and land Elevation Satellite (ICEsat), a laser altimeter provided data to detect polar area elevation change between 2003 and 2009. CryoSat-2 launched with Synthetic Aperture Radar (SAR)/Interferometric Radar Altimeter (SIRAL) in April 2010 can provide data to estimate time-series of Arctic sea ice thickness. In this study, Arctic sea ice freeboard and thickness between 2011 and 2014 were estimated using CryoSat-2 SAR and SARIn mode data that have sea ice surface height relative to the reference ellipsoid WGS84. In order to estimate sea ice thickness, freeboard, i.e., elevation difference between the top of sea ice surface should be calculated. Freeboard can be estimated through detecting leads. We proposed a novel lead detection approach. CryoSat-2 profiles such as pulse peakiness, backscatter sigma-0, stack standard deviation, skewness and kurtosis were examined to distinguish leads from sea ice. Near-real time cloud-free MODIS images corresponding to CryoSat-2 data measured were used to visually identify leads. Rule-based machine learning approaches such as See5.0 and random forest were used to identify leads. The proposed lead detection approach better distinguished leads from sea ice than the existing approaches. With the freeboard height calculated using the lead detection approach, sea ice thickness was finally estimated using the Archimedes' buoyancy principle. The estimated sea ice freeboard and thickness were validated using ESA airborne Ku-band interferometric radar and Airborne Electromagnetic (AEM) data.

Phase Decomposition in the Fe-rich Fe-Ni-S System from 900 Degrees C to 300 Degrees C--Application to Meteoritic Metal

NASA Astrophysics Data System (ADS)

Ma, L.; Williams, D. B.; Goldstein, J. I.

1995-09-01

It has been observed that metal particles in ordinary chondrites contain essentially no P and that the tetrataenite rim of the metal particles is much wider than that in other types of meteorites, especially when the taenite rim abuts troilites (FeS) [1]. It is possible that S plays an important role in the formation of the zoned tetrataenite at low cooling temperatures. Most of the studies of the Fe-Ni-S system have concentrated on high temperature and high Ni-high S part of the ternary diagram [2][3]. In this study we have systematically investigated the microstructure and microchemistry of the Fe-rich Fe-Ni-S system in regions where meteoritic metal forms from 900 degrees C down to 300 degrees C. High spatial resolution electron probe microanalysis (EPMA) and analytical electron microscopy (AEM) techniques were employed. The two and three phase boundaries at high temperatures (900 degrees C to 600 degrees C) are consistent with previous studies. However, at 500 degrees C, an Fe-Ni phase with 51.6 +/- 1.4 wt.% Ni was observed to form along some of the g/g and g/FeS boundaries. The size of this Fe-Ni phase is as large as 10 micrometers in width. AEM analysis indicates that this Fe-Ni phase may have even higher Ni content, 56 wt.%. In addition, the phase has a FCC structure and is disordered. Because the composition of this phase is very close to the stoichiometric composition of FeNi, it is very likely that the phase is tetrataenite. High Ni precipitates with similar morphology were also observed in the Fe-Ni-S alloy aged at 400 degrees C. However, the Ni content is 60.9 +/- 4.0 wt.% measured with EPMA, which is much higher than that in the corresponding 500 degree C sample. The fact that all the high Ni precipitates formed at boundaries of g/g or g/FeS indicates the boundaries are favorable energy nucleation sites. Such a high Ni phase with a Ni content over 60 wt.% has not been observed in the Fe-Ni and Fe-Ni (P) systems above 400 degrees C. The tetrataenite phase forms in the Fe-Ni-S system at higher temperatures (500 degrees C) than in the Fe-Ni and Fe-Ni (P) systems (<400 degrees C) [4]. Because the tetrataenite phase forms in the Fe-Ni-S system at higher temperatures, the tetrataenite rim in chondrites should be much wider than that in other meteorites where phase growth is controlled by the presence of P. It is possible that the Ni distribution in the metal phases of chondrites is dictated by the g/FeS and g/FeS/g' tie-line variations rather than by a/g tie-lines in the case of iron or stony iron meteorites. References: [1] Holland-Duffield C. E. et al. (1991) Meteoritics, 26, 97-103. [2] Kullerud G. (1963) Carnegie Inst. Wash. Yearb., 62, 175-189. [3] Clark L. A. and Kullerud G. (1963) Econ. Geol., 58, 853-885. [4] Yang C. W. (1994) Ph.D. dissertation, Lehigh Univ.

Disappearing Twelvemile Lake in Alaska's Discontinuous Permafrost: Scoping Analysis of Water Budget

NASA Astrophysics Data System (ADS)

Jepsen, S. M.; Voss, C. I.; Walvoord, M. A.; Minsley, B. J.; Rose, J.; Smith, B. D.

2011-12-01

The number and size of lakes in northern high-latitude regions have undergone significant changes over the last 3 decades or longer, possibly in association with climate warming. In the Yukon Flats Basin (YFB) of interior Alaska, a region underlain by discontinuous permafrost, these changes have not been uniform among lake drainage basins, suggesting the importance of local processes that are not well understood. As an example in the YFB, Twelvemile Lake has decreased in area by 60% since 1984, while neighboring Buddy Lake, 2 km to the southeast, has shown no significant change (see Figure). The objective of this study is to evaluate physical mechanisms that could account for the lowering of Twelvemile Lake, using a combination of water flux approximations, historical climate data and the permafrost distribution as interpreted from airborne electromagnetics (AEM). All possible in- and out-flux pathways to the lake are considered and compared with the observed rate of change in the lake's volume, to rank the importance of each pathway as a contributor to the change in lake level. Results from the AEM survey suggest the presence of a ~200 m diameter open-talik beneath the lake, and subsurface, channel-shaped depressions in the permafrost table ("channels") that may direct shallow groundwater (GW) flow into or out of the lake basin. An increase in potential evapotranspiration of only ~2 cm yr-1 from the period of 1950-1980 to 1981-2010 is found to be insignificant relative to the observed 13 cm yr-1 rate of lake level lowering since the early 1980's. Thus, alternative water pathways are needed to explain the lake level change. The following four processes are shown to potentially have a significant contribution to the observed rate of lake level change: (i) Reduced water inputs from decreased snowpacks; (ii) Increased infiltration of snowmelt due to changes in wintertime ice content of subnivean soil; (iii) Changes in GW flow through inlet and outlet channels to the lake basin due to ground ice dynamics; (iv) Changes in GW flow to the lake resulting from lateral ice aggradation or degradation in the open-talik. In conclusion, the lowering of Twelvemile Lake may result from a combination of processes that are operating in addition to those commonly associated with thermokarst lakes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagy, Kathryn L.; Sturchio, Neil C.

This project, renewal of a previous EMSP project of the same title, is in its first year of funding at the University of Illinois at Chicago. The purpose is to continue investigating rates and mechanisms of reactions between primary sediment minerals found in the Hanford subsurface and leaked waste tank solutions. The goals are to understand processes that result in (1) changes in porosity and permeability of the sediment and resultant changes in flow paths of the contaminant plumes, (2) formation of secondary precipitates that can take up contaminants in their structures, and (3) release of mineral components that canmore » drive redox reactions affecting dissolved contaminant mobility. A post-doctoral scientist, Dr. Sherry Samson, has been hired and two masters of science students are beginning to conduct experimental research. One research project that is underway is focused on measurement of the dissolution rates of plagioclase feldspar in high pH, high nitrate, high Al-bearing solutions characteristic of the BX tank farms. The first set of experiments is being conduced at room temperature. Subsequent experiments will examine the role of temperature because tank solutions in many cases were near boiling when leakage is thought to have occurred and temperature gradients have been observed beneath the SX and BX tank farms. The dissolution experiments are being conducted in stirred-flow kinetic reactors using powdered labradorite feldspar from Pueblo Park, New Mexico.« less

Enrollment into a time sensitive clinical study in the critical care setting: results from computerized septic shock sniffer implementation.

PubMed

Herasevich, Vitaly; Pieper, Matthew S; Pulido, Juan; Gajic, Ognjen

2011-01-01

Recruitment of patients into time sensitive clinical trials in intensive care units (ICU) poses a significant challenge. Enrollment is limited by delayed recognition and late notification of research personnel. The objective of the present study was to evaluate the effectiveness of the implementation of electronic screening (septic shock sniffer) regarding enrollment into a time sensitive (24 h after onset) clinical study of echocardiography in severe sepsis and septic shock. We developed and tested a near-real time computerized alert system, the septic shock sniffer, based on established severe sepsis/septic shock diagnostic criteria. A sniffer scanned patients' data in the electronic medical records and notified the research coordinator on call through an institutional paging system of potentially eligible patients. The performance of the septic shock sniffer was assessed. The septic shock sniffer performed well with a positive predictive value of 34%. Electronic screening doubled enrollment, with 68 of 4460 ICU admissions enrolled during the 9 months after implementation versus 37 of 4149 ICU admissions before sniffer implementation (p<0.05). Efficiency was limited by study coordinator availability (not available at nights or weekends). Automated electronic medical records screening improves the efficiency of enrollment and should be a routine tool for the recruitment of patients into time sensitive clinical trials in the ICU setting.

Facebook activity of residents and fellows and its impact on the doctor-patient relationship.

PubMed

Moubarak, Ghassan; Guiot, Aurélie; Benhamou, Ygal; Benhamou, Alexandra; Hariri, Sarah

2011-02-01

Facebook is an increasingly popular online social networking site. The purpose of this study was to describe the Facebook activity of residents and fellows and their opinions regarding the impact of Facebook on the doctor-patient relationship. An anonymous questionnaire was emailed to 405 residents and fellows at the Rouen University Hospital, France, in October 2009. Of the 202 participants who returned the questionnaire (50%), 147 (73%) had a Facebook profile. Among responders, 138 (99%) displayed their real name on their profile, 136 (97%) their birthdates, 128 (91%) a personal photograph, 83 (59%) their current university and 76 (55%) their current position. Default privacy settings were changed by 61% of users, more frequently if they were registered for >1 year (p=0.02). If a patient requested them as a 'friend', 152 (85%) participants would automatically decline the request, 26 (15%) would decide on an individual basis and none would automatically accept the request. Eighty-eight participants (48%) believed that the doctor-patient relationship would be altered if patients discovered that their doctor had a Facebook account, but 139 (76%) considered that it would change only if the patient had open access to their doctor's profile, independent of its content. Residents and fellows frequently use Facebook and display personal information on their profiles. Insufficient privacy protection might have an impact the doctor-patient relationship.

Organisational merger and psychiatric morbidity: a prospective study in a changing work organisation.

PubMed

Väänänen, Ari; Ahola, Kirsi; Koskinen, Aki; Pahkin, Krista; Kouvonen, Anne

2011-08-01

Prospective studies on the relationship between organisational merger and mental health have been conducted using subjective health indicators. The objective of this prospective occupational cohort study was to examine whether a negative change during an organisational merger is an independent predictive factor of psychiatric morbidity. Survey data on organisational characteristics, health and other factors were collected prior to (1996) and after the merger (2000); register data on psychiatric morbidity were collected at baseline (1/1/1994-30/9/2000) and during the follow-up (1/10/2000-31/12/2005). Participants were 6511 (77% men) industrial employees aged 21-65 years with no register-based diagnosed psychiatric events prior to the follow-up (the Still Working Study). During the follow-up, 252 participants were admitted to the hospital due to psychiatric disorders, were prescribed a psychotropic drug or attempted or committed suicide. A negative self-reported change in the work organisation during the merger was associated with increased risk of postmerger psychiatric event (HR 1.60, 95% CI 1.19 to 2.14). This association was independent of mental health-related factors measured before the merger announcement, such as demographic characteristics, occupational status, personal orientation to life, self-rated health, self-reported psychiatric morbidity or chronic disease. A negative change in work organisation during an organisational merger may elevate the risk for postmerger psychiatric morbidity.

Trampoline-related injuries in children: a preliminary biomechanical model of multiple users.

PubMed

Menelaws, Simon; Bogacz, Andrew R; Drew, Tim; Paterson, Brodie C

2011-07-01

The recent popularity of domestic trampolines has seen a corresponding increase in injured children. Most injuries happen on the trampoline mat when there are multiple users present. This study sought to examine and simulate the forces and energy transferred to a child's limbs when trampolining with another person of greater mass. The study used a computational biomechanical model. The simulation demonstrated that when two masses bounce out of phase on a trampoline, a transfer of kinetic energy from the larger mass to the smaller mass is likely to occur. It predicted that when an 80 kg adult is on a trampoline with a 25 kg child, the energy transfer is equivalent to the child falling 2.8 m onto a solid surface. Additionally, the rate of loading on the child's bones and ligaments is greater than that on the accompanying adult. Current guidelines are clear that more than one user on a trampoline at a time is a risk factor for serious injury; however, the majority of injuries happen in this scenario. The model predicted that there are high energy transfers resulting in serious fracture and ligamentous injuries to children and that this could be equated to equivalent fall heights. This provides a clear take-home message, which can be conveyed to parents to reduce the incidence of trampoline-related injuries.

Long-term performance and characterization of microbial desalination cells in treating domestic wastewater.

PubMed

Luo, Haiping; Xu, Pei; Ren, Zhiyong

2012-09-01

Microbial desalination cell represents a new technology for simultaneous wastewater treatment, water desalination, and energy production. This study characterized the long-term performance of MDC during wastewater treatment and identified the key factors that caused performance decline. The 8-month operation shows that MDC performance decreased over time, as indicated by a 47% decline in current density, a 46% drop in Columbic efficiency, and a 27% decrease in desalination efficiency. Advanced electrochemical, microscopy, and spectroscopy analyses all confirmed biofouling on the anion exchange membrane, which increased system resistance and reduced ionic transfer and energy conversion efficiency. Minor chemical scaling was found on the cation exchange membrane surface. Microbial communities became less diverse at the end of operation, and Proteobacteria spp. was dominant on both anode and AEM fouling layer surface. These results provide insights into the viability of long-term MDC operation on reactor performance and direct system development through membrane optimization. Copyright © 2012 Elsevier Ltd. All rights reserved.

Compendium of meteorological space programs, satellites, and experiments

NASA Technical Reports Server (NTRS)

Dubach, Leland L.; Ng, Carolyn

1988-01-01

This compendium includes plans and events known to the authors through January 1987. Compilation of the information began in 1967. This document is intended: (1) as a historical record of all satellites and instrumentation that has been useful for meteorological research or operational uses; and (2) as a working document to be used to assist meteorologists in identifying meteorological satellites, locating data from these satellites, and understanding experiment operation which is related to satellite data that may be of interest to them. A summary of all known launched satellites for all countries and their experiments, which were concerned with meteorological operations or research, are included. Programs covered include AEM, Apollo, ATS, Bhaskara, Cosmos, Discoverer, DMSP, DOD, DODGE, EOLE, ERBE, ESSA, Explorer, Gemini, GMS, GOES/SMS, INSAT, IRS, LANDSAT, Mercury, Meteor 1 and 2, Meteosat, Molniya, MOS, Nimbus, NOAA (1-5)/ITOS, NOAA (6,7,D)/TIROS-N, NOAA (8-10, H-J)/ATN, Salyut, Seasat, Shuttle 1, Shuttle 2: Spacelab, Skylab, Soyuz, TIROS, TOPEX, Vanguard, Voskhod, Vostok, and Zond.

Electrical power from sea and river water by reverse electrodialysis: a first step from the laboratory to a real power plant.

PubMed

Veerman, Joost; Saakes, Michel; Metz, Sybrand J; Harmsen, G Jan

2010-12-01

Electricity can be produced directly with reverse electrodialysis (RED) from the reversible mixing of two solutions of different salinity, for example, sea and river water. The literature published so far on RED was based on experiments with relatively small stacks with cell dimensions less than 10 × 10 cm(2). For the implementation of the RED technique, it is necessary to know the challenges associated with a larger system. In the present study we show the performance of a scaled-up RED stack, equipped with 50 cells, each measuring 25 × 75 cm(2). A single cell consists of an AEM (anion exchange membrane) and a CEM (cation exchange membrane) and therefore, the total active membrane area in the stack is 18.75 m(2). This is the largest dimension of a reverse electrodialysis stack published so far. By comparing the performance of this stack with a small stack (10 × 10 cm(2), 50 cells) it was found that the key performance parameter to maximal power density is the hydrodynamic design of the stack. The power densities of the different stacks depend on the residence time of the fluids in the stack. For the large stack this was negatively affected by the increased hydrodynamic losses due to the longer flow path. It was also found that the large stack generated more power when the sea and river water were flowing in co-current operation. Co-current flow has other advantages, the local pressure differences between sea and river water compartments are low, hence preventing leakage around the internal manifolds and through pinholes in the membranes. Low pressure differences also enable the use of very thin membranes (with low electrical resistance) as well as very open spacers (with low hydrodynamic losses) in the future. Moreover, we showed that the use of segmented electrodes increase the power output by 11%.

Assimilation of attenuated data from X-band network radars using ensemble Kalman filter

NASA Astrophysics Data System (ADS)

Cheng, Jing

To use reflectivity data from X-band radars for quantitative precipitation estimation and storm-scale data assimilation, the effect of attenuation must be properly accounted for. Traditional approaches try to make correction to the attenuated reflectivity first before using the data. An alternative, theoretically more attractive approach builds the attenuation effect into the reflectivity observation operator of a data assimilation system, such as an ensemble Kalman filter (EnKF), allowing direct assimilation of the attenuated reflectivity and taking advantage of microphysical state estimation using EnKF methods for a potentially more accurate solution. This study first tests the approach for the CASA (Center for Collaborative Adaptive Sensing of the Atmosphere) X-band radar network configuration through observing system simulation experiments (OSSE) for a quasi-linear convective system (QLCS) that has more significant attenuation than isolated storms. To avoid the problem of potentially giving too much weight to fully attenuated reflectivity, an analytical, echo-intensity-dependent model for the observation error (AEM) is developed and is found to improve the performance of the filter. By building the attenuation into the forward observation operator and combining it with the application of AEM, the assimilation of attenuated CASA observations is able to produce a reasonably accurate analysis of the QLCS inside CASA radar network coverage. Compared with foregoing assimilation of radar data with weak radar reflectivity or assimilating only radial velocity data, our method can suppress the growth of spurious echoes while obtaining a more accurate analysis in the terms of root-mean-square (RMS) error. Sensitivity experiments are designed to examine the effectiveness of AEM by introducing multiple sources of observation errors into the simulated observations. The performance of such an approach in the presence of resolution-induced model error is also evaluated and good results are obtained. The same EnKF framework with attenuation correction is used to test different possible configurations of 2 hypothetical radars added to the existing network of 4 CASA radars through OSSEs. Though plans to expand the CASA radar network did not materialize, such experiments can provide guidance in the site selection of future X-band or other short-wavelength radar networks, as well as examining the benefit of X-band radar networks that consist of a much larger number of radars. Two QLCSs with different propagation speeds are generated and serve as the truth for our OSSEs. Assimilation and forecast results are compared among the OSSEs, assimilating only X-band or short-wavelength radar data. Overall, radar networks with larger downstream spatial coverage tend to provide overall the best analyses and 1-hour forecasts. The best analyses and forecasts of convective scale structure, however, are obtained when Dual- or Multi-Doppler coverage is preferred, even at the expense of minor loss in spatial coverage. Built-in attenuation correction is then applied, for the first time, to a real case (the 24 May 2011 tornadic storm near Chickasha, Oklahoma), using data from the X-band CASA radars. The attenuation correction procedure is found to be very effective---the analyses obtained using attenuated data are better than those obtained using pre-corrected data when all the values of reflectivity observations are assimilated. The effectiveness of the procedure is further examined by comparing the deterministic and ensemble forecasts started from the analysis of each experiment. The deterministic forecast experiment results indicate that assimilating un-corrected observations directly actually retains some information that might be lost in the pre-corrected CASA observations by forecasting a longer-lasting trailing line, similar to that observed in WSR-88D data. In the ensemble forecasts, assimilating un-corrected observations directly, using our attenuation-correcting EnKF, results in a forecast with a more intense tornado track than the experiment that assimilates all values of pre-corrected CASA data. This work is the first to assimilate attenuated observations from a radar network in OSSEs, as well as the first attempt to directly assimilate real, uncorrected CASA data into a numerical weather prediction (NWP) model using EnKF.

Development and pilot phase of a European MS register.

PubMed

Flachenecker, Peter; Khil, Laura; Bergmann, Sverrir; Kowalewski, Mariusz; Pascu, Ion; Pérez-Miralles, Francisco; Sastre-Garriga, Jaume; Zwingers, Thomas

2010-10-01

The MS-ID (Multiple Sclerosis Information Dividend) project was initiated by the European Multiple Sclerosis Platform (EMSP) in 2007 in order to identify and address major inequalities of MS treatment and care and thus eliminate disparities across the EU. One major approach to reach these goals in the longer term is the implementation of a European MS register for MS. The feasibility of an EU MS register was piloted among five countries (Germany, Iceland, Poland, Romania and Spain). Each country liaised with one documentation centre. Countries and test centres were both chosen in a way that a heterogeneous health care structure was provided. After reaching consensus about the data set, comprehension and acceptability of the two questionnaires-representing both the physician's and the patient's perspective-were tested with 20 MS patients in each country. In a 6-month data collection period, data from 547 patients were recorded. Most sections of the questionnaires were available for more than 90% of patients. The results obtained from the pilot phase of the European MS register indicate that it is feasible to collect standardized data across Europe. Thus, the European MS register may be a valuable instrument to compare treatment and care of MS across countries, estimate the cost of MS in Europe and monitor the implementation of and adherence to guidelines. It may help to reduce the disparities in MS care and treatment throughout Europe and eventually improve the quality of life of people with MS.

Subsurface high resolution definition of subsurface heterogeneity for understanding the biodynamics of natural field systems: Advancing the ability for scaling to field conditions. 1998 annual progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Majer, E.L.; Brockman, F.J.

1998-06-01

'This research is an integrated physical (geophysical and hydrologic) and microbial study using innovative geophysical imaging and microbial characterization methods to identify key scales of physical heterogeneities that affect the biodynamics of natural subsurface environments. Data from controlled laboratory and in-situ experiments at the INEEL Test Area North (TAN) site are being used to determine the dominant physical characteristics (lithologic, structural, and hydrologic) that can be imaged in-situ and correlated with microbial properties. The overall goal of this research is to contribute to the understanding of the interrelationships between transport properties and spatially varying physical, chemical, and microbiological heterogeneity. Themore » outcome will be an improved understanding of the relationship between physical and microbial heterogeneity, thus facilitating the design of bioremediation strategies in similar environments. This report summarizes work as of May 1998, the second year of the project. This work is an extension of basic research on natural heterogeneity first initiated within the DOE/OHER Subsurface Science Program (SSP) and is intended to be one of the building blocks of an integrated and collaborative approach with an INEEL/PNNL effort aimed at understanding the effect of physical heterogeneity on transport properties and biodynamics in natural systems. The work is closely integrated with other EMSP projects at INEEL (Rick Colwell et al.) and PNNL (Fred Brockman and Jim Fredrickson).'« less

Medicine and the Holocaust: a visit to the Nazi death camps as a means of teaching medical ethics in the Israel Defense Forces Medical Corps.

PubMed

Oberman, Anthony S; Brosh-Nissimov, Tal; Ash, Nachman

2010-12-01

A novel method of teaching military medical ethics, medical ethics and military ethics in the Israel Defense Force (IDF) Medical Corps, essential topics for all military medical personnel, is discussed. Very little time is devoted to medical ethics in medical curricula, and even less to military medical ethics. Ninety-five per cent of American students in eight medical schools had less than 1 h of military medical ethics teaching and few knew the basic tenets of the Geneva Convention. Medical ethics differs from military medical ethics: the former deals with the relationship between medical professional and patient, while in the latter military physicians have to balance between military necessity and their traditional priorities to their patients. The underlying principles, however, are the same in both: the right to life, autonomy, dignity and utility. The IDF maintains high moral and ethical standards. This stems from the preciousness of human life in Jewish history, tradition and religious law. Emphasis is placed on these qualities within the Israeli education system; the IDF teaches and enforces moral and ethical standards in all of its training programmes and units. One such programme is 'Witnesses in Uniform' in which the IDF takes groups of officers to visit Holocaust memorial sites and Nazi death camps. During these visits daily discussions touch on intricate medical and military ethical issues, and contemporary ethical dilemmas relevant to IDF officers during active missions.

Validation of the Ottawa Knee Rule in Iran: a prospective study.

PubMed

Jalili, Mohammad; Gharebaghi, Hadi

2010-11-01

This study was designed to determine the accuracy of the Ottawa Knee Rule (OKR) when applied to patients with acute knee injury in the Iranian population of the Imam Hospital Emergency Department (ED) at. This prospective cohort validation study included a convenience sample of all patients with a blunt knee injury sustained in the preceding 7 days presenting to the ED of a tertiary care teaching hospital during the study period. Patients were assessed for the five variables comprising the OKR, and a standardised data form was completed for each patient. Standard knee radiographs were ordered on all patients irrespective of the determination of the rule. The rules were interpreted by the primary investigator on the basis of the data sheet and the final orthopaedist radiograph reading. Outcome measures of this study were: sensitivity, specificity, positive predictive value and negative predictive value of the OKR. A total of 283 patients were enrolled in the study. 22 fractures (7.77%) were detected. The decision rule had a sensitivity of 0.95 (95% CI 0.77 to 0.99), and a specificity of 0.44 (95% CI 0.37 to 0.50). The potential reduction in use of radiography was estimated to be 41%. The OKR missed only one fracture. Prospective validation has shown that the OKR is a highly sensitive tool for detecting knee fractures and has the potential to reduce the number of radiographs in patients with acute knee injuries.

Automated concept-level information extraction to reduce the need for custom software and rules development.

PubMed

D'Avolio, Leonard W; Nguyen, Thien M; Goryachev, Sergey; Fiore, Louis D

2011-01-01

Despite at least 40 years of promising empirical performance, very few clinical natural language processing (NLP) or information extraction systems currently contribute to medical science or care. The authors address this gap by reducing the need for custom software and rules development with a graphical user interface-driven, highly generalizable approach to concept-level retrieval. A 'learn by example' approach combines features derived from open-source NLP pipelines with open-source machine learning classifiers to automatically and iteratively evaluate top-performing configurations. The Fourth i2b2/VA Shared Task Challenge's concept extraction task provided the data sets and metrics used to evaluate performance. Top F-measure scores for each of the tasks were medical problems (0.83), treatments (0.82), and tests (0.83). Recall lagged precision in all experiments. Precision was near or above 0.90 in all tasks. Discussion With no customization for the tasks and less than 5 min of end-user time to configure and launch each experiment, the average F-measure was 0.83, one point behind the mean F-measure of the 22 entrants in the competition. Strong precision scores indicate the potential of applying the approach for more specific clinical information extraction tasks. There was not one best configuration, supporting an iterative approach to model creation. Acceptable levels of performance can be achieved using fully automated and generalizable approaches to concept-level information extraction. The described implementation and related documentation is available for download.

Is there a right not to know one's sex? The ethics of 'gender verification' in women's sports competition.

PubMed

Wiesemann, Claudia

2011-04-01

The paper discusses the current medical practice of 'gender verification' in sports from an ethical point of view. It takes the recent public discussion about 800 m runner Caster Semenya as a starting point. At the World Championships in Athletics 2009 in Berlin, Germany, Semenya was challenged by competitors as being a so called 'sex impostor'. A medical examination to verify her sex ensued. The author analyses whether athletes like Semenya could claim a right not to know that is generally acknowledged in human genetics and enforced by international and national genetic privacy laws. The relevance of this right for genetic diagnosis in sports is discussed. To this end, the interests of the athlete concerned and of third parties are balanced according to the expected benefits and harms.Harm is documented in a number of cases and includes unjustified disqualification, severe sex and gender identity crisis, demeaning reactions, social isolation, depression and suicide. Benefits are dubious as most cases of intersex are considered irrelevant for sports competition. It has to be concluded that the benefits to be gained from 'gender verification' in sports via genetic testing do not outweigh the grave individual disadvantages. The current practice of athletic associations to largely ignore the right of competitors not to know does not comply with prevailing ethical provisions on the protection of sensitive personal data. Therefore, genetic 'gender verification' in sports should be abolished.

Email triage is an effective, efficient and safe way of managing new referrals to a neurologist.

PubMed

Patterson, Victor; Humphreys, Jenny; Henderson, Mark; Crealey, Grainne

2010-10-01

Patients referred to secondary care in the UK often wait many months to be seen, and the UK government has announced various initiatives to address this issue. Since 2002, we have developed an email referral system which allows some neurological referrals to be managed by advice and investigations rather than by a conventional hospital clinic appointment. This system has previously been shown to reduce clinic attendances and to be acceptable to patients and their general practitioners (GPs). To analyse the effects of an email triage system on waiting times, cost of care and safety over 5 years. Referral numbers and waiting times for clinics using this system were analysed. Cost was determined by comparing detailed costs with those of conventional care. Safety was analysed by examining the GP records of all patients referred from a single practice who had been dealt with by advice or investigation, noting deaths, re-referrals and changes in diagnosis. Waiting times fell from 72 to 4 weeks, despite an increase in referrals. The cost per patient of email referral was about £100, compared with £152 for conventional care, a 35% reduction. Safety data on 120 individuals showed a minor change in diagnosis in three. This system is safe, effective (in reducing waiting times) and efficient. It enables neurologists to focus on patients with significant neurological disease and, if applied more widely, could reduce costs and waiting times for neurology services in the UK.

Adaptive sampling of AEM transients

NASA Astrophysics Data System (ADS)

Di Massa, Domenico; Florio, Giovanni; Viezzoli, Andrea

2016-02-01

This paper focuses on the sampling of the electromagnetic transient as acquired by airborne time-domain electromagnetic (TDEM) systems. Typically, the sampling of the electromagnetic transient is done using a fixed number of gates whose width grows logarithmically (log-gating). The log-gating has two main benefits: improving the signal to noise (S/N) ratio at late times, when the electromagnetic signal has amplitudes equal or lower than the natural background noise, and ensuring a good resolution at the early times. However, as a result of fixed time gates, the conventional log-gating does not consider any geological variations in the surveyed area, nor the possibly varying characteristics of the measured signal. We show, using synthetic models, how a different, flexible sampling scheme can increase the resolution of resistivity models. We propose a new sampling method, which adapts the gating on the base of the slope variations in the electromagnetic (EM) transient. The use of such an alternative sampling scheme aims to get more accurate inverse models by extracting the geoelectrical information from the measured data in an optimal way.

Preparation and performance evaluation of novel alkaline stable anion exchange membranes

NASA Astrophysics Data System (ADS)

Irfan, Muhammad; Bakangura, Erigene; Afsar, Noor Ul; Hossain, Md. Masem; Ran, Jin; Xu, Tongwen

2017-07-01

Novel alkaline stable anion exchange membranes are prepared from various amounts of N-methyl dipicolylamine (MDPA) and brominated poly (2,6-dimethyl-1,4-phenylene oxide) (BPPO). The dipicolylamine and MDPA are synthesized through condensation reaction and confirmed by 1H NMR spectroscopy. The morphologies of prepared membranes are investigated by atomic force microscopy (AFM), fourier transform infrared spectroscopy (FTIR), 1H NMR spectroscopy and scanning electron microscopy (SEM). The electrochemical and physical properties of AEMs are tested comprising water uptake (WU), ion exchange capacity (IEC), alkaline stability, linear expansion ratio (LER), thermal stability and mechanical stability. The obtained hydroxide conductivity of MDPA-4 is 66.5 mS/cm at 80 °C. The MDPA-4 membrane shows good alkaline stability, high hydroxide conductivity, low methanol permeability (3.43 × 10-7 cm2/s), higher selectivity (8.26 × 107 mS s/cm3), less water uptake (41.1%) and lower linear expansion (11.1%) despite of high IEC value (1.62 mmol/g). The results prove that MDPA membranes have great potential application in anion exchange membrane fuel cell.

Mexican Space Weather Service (SCIESMEX)

NASA Astrophysics Data System (ADS)

Gonzalez-Esparza, A.; De la Luz, V.; Mejia-Ambriz, J. C.; Aguilar-Rodriguez, E.; Corona-Romero, P.; Gonzalez, L. X.

2015-12-01

Recent modifications of the Civil Protection Law in Mexico include now specific mentions to space hazards and space weather phenomena. During the last few years, the UN has promoted international cooperation on Space Weather awareness, studies and monitoring. Internal and external conditions motivated the creation of a Space Weather Service in Mexico (SCIESMEX). The SCIESMEX (www.sciesmex.unam.mx) is operated by the Geophysics Institute at the National Autonomous University of Mexico (UNAM). The UNAM has the experience of operating several critical national services, including the National Seismological Service (SSN); besides that has a well established scientific group with expertise in space physics and solar- terrestrial phenomena. The SCIESMEX is also related with the recent creation of the Mexican Space Agency (AEM). The project combines a network of different ground instruments covering solar, interplanetary, geomagnetic, and ionospheric observations. The SCIESMEX has already in operation computing infrastructure running the web application, a virtual observatory and a high performance computing server to run numerical models. SCIESMEX participates in the International Space Environment Services (ISES) and in the Inter-progamme Coordination Team on Space Weather (ICTSW) of the Word Meteorological Organization (WMO).

Experimental and analytical analysis of polarization and water transport behaviors of hydrogen alkaline membrane fuel cell

NASA Astrophysics Data System (ADS)

Huo, Sen; Zhou, Jiaxun; Wang, Tianyou; Chen, Rui; Jiao, Kui

2018-04-01

Experimental test and analytical modeling are conducted to investigate the operating behavior of an alkaline electrolyte membrane (AEM) fuel cell fed by H2/air (or O2) and explore the effect of various operating pressures on the water transfer mechanism. According to the experimental test, the cell performance is greatly improved through increasing the operating pressure gradient from anode to cathode which leads to significant liquid water permeation through the membrane. The high frequency resistance of the A901 alkaline membrane is observed to be relatively stable as the operating pressure varies based on the electrochemical impedance spectroscopy (EIS) method. Correspondingly, based on the modeling prediction, the averaged water content in the membrane electrode assembly (MEA) does not change too much which leads to the weak variation of membrane ohmic resistance. This reveals that the performance enhancement should give the credit to better electro-chemical reaction kinetics for both the anode and cathode, also prone by the EIS results. The reversion of water back diffusion direction across the membrane is also observed through analytical solution.

Anion exchange membranes based on terminally crosslinked methyl morpholinium-functionalized poly(arylene ether sulfone)s

NASA Astrophysics Data System (ADS)

Kwon, Sohyun; Rao, Anil H. N.; Kim, Tae-Hyun

2018-01-01

Azide-assisted terminal crosslinking of methyl morpholinium-functionalized poly(arylene ether sulfone) block copolymers yields products (xMM-PESs) suitable for use as anion exchange membranes. By combining the advantages of bulky morpholinium conductors and our unique polymer network crosslinked only at the termini of the polymer chains, we can produce AEMs that after the crosslinking show minimal loss in conductivity, yet with dramatically reduced water uptake. Terminal crosslinking also significantly increases the thermal, mechanical and chemical stability levels of the membranes. A high ion conductivity of 73.4 mS cm-1 and low water uptake of 26.1% at 80 °C are obtained for the crosslinked membrane with higher amount of hydrophilic composition, denoted as xMM-PES-1.5-1. In addition, the conductivity of the crosslinked xMM-PES-1.5-1 membrane exceeds that of its non-crosslinked counterpart (denoted as MM-PES-1.5-1) above 60 °C at 95% relative humidity because of its enhanced water retention capacity caused by the terminally-crosslinked structure.

DOE Office of Scientific and Technical Information (OSTI.GOV)

WANG,YIFENG; XU,HUIFANG

Correctly identifying the possible alteration products and accurately predicting their occurrence in a repository-relevant environment are the key for the source-term calculation in a repository performance assessment. Uraninite in uranium deposits has long been used as a natural analog to spent fuel in a repository because of their chemical and structural similarity. In this paper, a SEM/AEM investigation has been conducted on a partially alternated uraninite sample from a uranium ore deposit of Shinkolobwe of Congo. The mineral formation sequences were identified: uraninite {yields} uranyl hydrates {yields} uranyl silicates {yields} Ca-uranyl silicates or uraninite {yields} uranyl silicates {yields} Ca-uranyl silicates.more » Reaction-path calculations were conducted for the oxidative dissolution of spent fuel in a representative Yucca Mountain groundwater. The predicted sequence is in general consistent with the SEM observations. The calculations also show that uranium carbonate minerals are unlikely to become major solubility-controlling mineral phases in a Yucca Mountain environment. Some discrepancies between model predictions and field observations are observed. Those discrepancies may result from poorly constrained thermodynamic data for uranyl silicate minerals.« less

Development and characterization of direct ethanol fuel cells using alkaline anion-exchange membranes

NASA Astrophysics Data System (ADS)

Lim, Peck Cheng

2009-08-01

Alkaline membrane fuel cell (AMFC) is a relatively new fuel cell technology that is generating considerable interests. It offers the electrocatalytic advantages of conventional alkaline fuel cells, and the manufacturing and cost advantages of solid polymer electrolyte fuel cells. This project was carried out to develop and characterize high performance membrane electrode assemblies (MEAs) for all-solid-state AMFCs. The primary fuel of interests is ethanol, but hydrogen was used in the development stages to facilitate the diagnostic and evaluation of the fuel cell performance. In the preliminary investigation, AMFC was assembled using off-the-shelf electrodes and anion-exchange membrane (AEM). It was found that the performance of AMFC operating on ethanol fuel was limited by a large high-frequency resistance (HFR) value. The advantage of using non-toxic ethanol fuel was also compromised by the need to add hydrazine and potassium hydroxide to the fuel blend. Subsequently, a high performance MEA was developed for an all-solid-state AMFC, in which liquid electrolyte or other additives were not required during the operation of the fuel cell. Ionomer was incorporated in the formulation of catalyst ink, and the catalyst ink was directly coated on the anion-exchange membrane (AEM). An ionomer content of 20 wt.% was found to be the optimum amount required in the catalyst layers. It was demonstrated that the AMFC generated a maximum power density of 365 mW/cm2 and 213 mW/cm 2 with the use of hydrogen/oxygen and hydrogen/pure air, respectively. The performance of the AMFC was also found to be influenced by exposure to carbon dioxide in the air. Hence, the CCMs were pre-treated in potassium hydroxide solution and pure oxygen was used to condition the fuel cell to maximize the power output from the AMFCs. Although satisfactory performance was demonstrated in the AMFC, its stability during cell operation remains a major issue. The poor stability was attributed to degradation of ionomer in the catalyst layers, especially at the catalyst/ionomer interfaces. Ethanol was also used as a fuel in the AMFC with newly developed MEAs. Wetproof gas diffusion layers (GDLs) was found to enhance mass transport in liquid-fed AMFC. With the use of 1M ethanol, the AMFC exhibited a maximum power density of 6.482 mW/cm2 and 3.380 mW/cm2 with pure oxygen and ambient air as oxidant, respectively. These maximum power density values are the highest reported to-date. However, significant work is still necessary in advancing the AMFC technology for direct alcohol fuel cell applications.

ALOHA: Automatic libraries of helicity amplitudes for Feynman diagram computations

NASA Astrophysics Data System (ADS)

de Aquino, Priscila; Link, William; Maltoni, Fabio; Mattelaer, Olivier; Stelzer, Tim

2012-10-01

We present an application that automatically writes the HELAS (HELicity Amplitude Subroutines) library corresponding to the Feynman rules of any quantum field theory Lagrangian. The code is written in Python and takes the Universal FeynRules Output (UFO) as an input. From this input it produces the complete set of routines, wave-functions and amplitudes, that are needed for the computation of Feynman diagrams at leading as well as at higher orders. The representation is language independent and currently it can output routines in Fortran, C++, and Python. A few sample applications implemented in the MADGRAPH 5 framework are presented. Program summary Program title: ALOHA Catalogue identifier: AEMS_v1_0 Program summary URL: http://cpc.cs.qub.ac.uk/summaries/AEMS_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: http://www.opensource.org/licenses/UoI-NCSA.php No. of lines in distributed program, including test data, etc.: 6094320 No. of bytes in distributed program, including test data, etc.: 7479819 Distribution format: tar.gz Programming language: Python2.6 Computer: 32/64 bit Operating system: Linux/Mac/Windows RAM: 512 Mbytes Classification: 4.4, 11.6 Nature of problem: An effcient numerical evaluation of a squared matrix element can be done with the help of the helicity routines implemented in the HELAS library [1]. This static library contains a limited number of helicity functions and is therefore not always able to provide the needed routine in the presence of an arbitrary interaction. This program provides a way to automatically create the corresponding routines for any given model. Solution method: ALOHA takes the Feynman rules associated to the vertex obtained from the model information (in the UFO format [2]), and multiplies it by the different wavefunctions or propagators. As a result the analytical expression of the helicity routines is obtained. Subsequently, this expression is automatically written in the requested language (Python, Fortran or C++) Restrictions: The allowed fields are currently spin 0, 1/2, 1 and 2, and the propagators of these particles are canonical. Running time: A few seconds for the SM and the MSSM, and up to a few minutes for models with spin 2 particles. References: [1] Murayama, H. and Watanabe, I. and Hagiwara, K., HELAS: HELicity Amplitude Subroutines for Feynman diagram evaluations, KEK-91-11, (1992) http://www-lib.kek.jp/cgi-bin/img_index?199124011 [2] C. Degrande, C. Duhr, B. Fuks, D. Grellscheid, O. Mattelaer, et al., UFO— The Universal FeynRules Output, Comput. Phys. Commun. 183 (2012) 1201-1214. arXiv:1108.2040, doi:10.1016/j.cpc.2012.01.022.

Ethical dilemmas in medical humanitarian practice: cases for reflection from Médecins Sans Frontières.

PubMed

Sheather, Julian; Shah, Tejshri

2011-03-01

Médecins Sans Frontières (MSF) is an independent medical humanitarian organisation working in over 70 countries. It has provided medical assistance for over 35 years to populations vulnerable through conflict, disease and inadequate health systems. Medical ethics define the starting point of the relationship between medical staff and patients. The ethics of humanitarian interventions and of research in conflict settings are much debated. However, less is known about the ethical dilemmas faced by medical humanitarian staff in their daily work. Ethical dilemmas can be intensified in humanitarian contexts by insecure environments, lack of optimum care, language barriers, potentially heightened power discrepancies between care providers and patients, differing cultural values and perceptions of patients, communities and medical staff. Time constraints, stressful conditions and lack of familiarity with ethical frameworks can prevent reflection on these dilemmas, as can frustration that such reflection does not necessarily provide instant solutions. Lack of reflection, however, can be distressing for medical practitioners and can reduce the quality of care. Ethical reflection has a central role in MSF, and the organisation uses ethical frameworks to help with clinical and programmatic decisions as well as in deliberations over operational research. We illustrate and discuss some real ethical dilemmas facing MSF teams. Only by sharing and seeking guidance can MSF and similar actors make more thoughtful and appropriate decisions. Our aim in sharing these cases is to invite discussion and dialogue in the wider medical community working in crisis, conflict or with severe resource limitations.

What to do now? How women with breast cancer make fertility preservation decisions.

PubMed

Snyder, Karrie Ann; Tate, Alexandra Lee

2013-07-01

There has been increased attention paid to cancer-related infertility and fertility preservation. However, how cancer patients decide whether or not to pursue fertility preservation has not been fully examined. The data come from 34 interviews with women in the USA diagnosed with breast cancer prior to 40 years of age who contemplated fertility preservation prior to cancer treatment. Fully transcribed interviews were coded through a three-staged inductive process. Three sets of factors that shaped the decision-making process of the respondents regarding fertility preservation treatment options were identified: perceived benefits (e.g. ability to use 'younger' eggs in the future), inhibiting concerns (e.g. success rates) and influential relationships (e.g. physicians, parents and partners). Respondents saw their main fertility preservation decision as choosing whether or not to pursue egg/embryo banking. The decision-making process was complicated and included both health-related and personal considerations, with many respondents reporting a lack of support services for fertility issues. Findings suggest that greater attention needs to be placed on presenting patients with a wider range of options. Those who counsel patients regarding fertility preservation decisions should be aware of the influence of relationship dynamics, broader health care concerns, and fertility histories on these decisions. KEY MESSAGE POINTS: While fertility preservation has garnered greater attention, less is known about how cancer patients make fertility preservation decisions. Despite the range of choices for fertility preservation, respondents identified egg/embryo banking as their primary option. Many factors outside of cancer concerns inhibit and facilitate fertility preservation decisions including fertility history and family relationship dynamics.

What constitutes consent when parents and daughters have different views about having the HPV vaccine: qualitative interviews with stakeholders.

PubMed

Wood, Fiona; Morris, Lucy; Davies, Myfanwy; Elwyn, Glyn

2011-08-01

The UK Human Papillomavirus (HPV) vaccine programme commenced in the autumn of 2008 for year 8 (age 12-13 years) schoolgirls. We examine whether the vaccine should be given when there is a difference of opinion between daughters and parents or guardians. Qualitative study using semi-structured interviews. A sample of 25 stakeholders: 14 professionals involved in the development of the HPV vaccination programme and 11 professionals involved in its implementation. Overriding the parents' wishes was perceived as problematic and could damage the relationship between school and parents. A number of practical problems were raised in relation to establishing whether parents were genuinely against their daughter receiving the vaccine. Although many respondents recognised that the Gillick guidelines were relevant in establishing whether a girl could provide consent herself, they still felt that there were significant problems in establishing whether girls could be assessed as Gillick competent. In some areas school nurses had been advised not to give the vaccine in the absence of parental consent. None of the respondents suggested that a girl should be vaccinated against her consent even if her parents wanted her to have the vaccine. While the Gillick guidelines provide a legal framework to help professionals make judgements about adolescents consenting to medical treatment, in practice there appears to be variable and confused interpretation of this guidance. Improved legal structures, management procedures and professional advice are needed to support those who are assessing competence and establishing consent to vaccinate adolescents in a school setting.

Chemiresistor microsensors for in-situ monitoring of volatile organic compounds : final LDRD report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Michael Loren; Hughes, Robert Clark; Kooser, Ara S.

2003-09-01

This report provides a summary of the three-year LDRD (Laboratory Directed Research and Development) project aimed at developing microchemical sensors for continuous, in-situ monitoring of volatile organic compounds. A chemiresistor sensor array was integrated with a unique, waterproof housing that allows the sensors to be operated in a variety of media including air, soil, and water. Numerous tests were performed to evaluate and improve the sensitivity, stability, and discriminatory capabilities of the chemiresistors. Field tests were conducted in California, Nevada, and New Mexico to further test and develop the sensors in actual environments within integrated monitoring systems. The field testsmore » addressed issues regarding data acquisition, telemetry, power requirements, data processing, and other engineering requirements. Significant advances were made in the areas of polymer optimization, packaging, data analysis, discrimination, design, and information dissemination (e.g., real-time web posting of data; see www.sandia.gov/sensor). This project has stimulated significant interest among commercial and academic institutions. A CRADA (Cooperative Research and Development Agreement) was initiated in FY03 to investigate manufacturing methods, and a Work for Others contract was established between Sandia and Edwards Air Force Base for FY02-FY04. Funding was also obtained from DOE as part of their Advanced Monitoring Systems Initiative program from FY01 to FY03, and a DOE EMSP contract was awarded jointly to Sandia and INEEL for FY04-FY06. Contracts were also established for collaborative research with Brigham Young University to further evaluate, understand, and improve the performance of the chemiresistor sensors.« less

Relative contribution of Prevotella intermedia and Pseudomonas aeruginosa to lung pathology in airways of patients with cystic fibrosis.

PubMed

Ulrich, Martina; Beer, Isabelle; Braitmaier, Peter; Dierkes, Michaela; Kummer, Florian; Krismer, Bernhard; Schumacher, Ulrike; Gräpler-Mainka, Ute; Riethmüller, Joachim; Jensen, Peter Ø; Bjarnsholt, Thomas; Høiby, Niels; Bellon, Gabriel; Döring, Gerd

2010-11-01

Patients with cystic fibrosis (CF) with Pseudomonas aeruginosa lung infections produce endobronchial mucus plugs allowing growth of obligate anaerobes including Prevotella spp. Whether obligate anaerobes contribute to the pathophysiology of CF lung disease is unknown. The virulence of Prevotella intermedia and Ps aeruginosa was investigated in vitro and in mice, antibodies against P intermedia in CF sera were assessed and a culture-independent detection method for P intermedia/P nigrescens in CF sputum was tested. P intermedia reached cell numbers of >10(5)->10(7) colony-forming units (CFU)/ml sputum. The majority of patients with CF (16/17; 94.1%) produced antibodies against two immunoreactive antigens of P intermedia. Culture supernatant fluids, collected from 10(9) P intermedia cells, were more cytotoxic to respiratory epithelial cells in vitro and inflammatory in mouse lungs than respective fluids from anaerobically grown Ps aeruginosa, while fluids from aerobically grown Ps aeruginosa had the highest cytotoxicity and inflammation. Both pathological effects were largely reduced when culture supernatant fluids from 10(7) cells of either species were used. P intermedia cells (∼10(6)CFU/lung) did not induce mortality in the agar beads lung infection mouse model, while Ps aeruginosa cells caused death in 30% of mice due to rapid multiplication. A P intermedia/P nigrescens-specific PNA probe was significantly more sensitive than culture-dependent diagnostic assays to detect these strict anaerobes. Ps aeruginosa and P intermedia become significantly virulent in vitro and in vivo when cell numbers exceed 10(8) CFU/lung.

Voluntary counselling and testing for HIV in a Zambian mining community: serial interviews with people testing negative.

PubMed

Sikasote, Janet; Grant, Liz; Chinn, David J; Macwang'i, Mubiana; Murray, Scott A

2011-08-01

To understand the influence of voluntary counselling and testing (VCT) and an HIV-negative result on subsequent sexual behaviour; and to identify the specific felt needs of those testing negative. Serial interviews, 6 months apart, with people who had tested negative, and three one-off focus group discussions with counsellors. Interviews were transcribed verbatim and analysed thematically. Paired transcripts were analysed longitudinally. Purposively sampled from first attenders for VCT who had tested negative. Four health-facility affiliated VCT centres in two mining towns in the Copperbelt Province of Zambia. Participants in the 42 initial and 31 follow-up interviews understood VCT as 'testing for HIV'. Most participants reported having adopted safer sexual behaviour months before attending VCT. They had already recognised personal susceptibility to HIV infection and reported engaging both emotionally and cognitively with the issues of testing. Ultimately attendance at testing was to know their status in order to regain control of their lives. Unmet post-test support needs were common and included additional information, supportive networks, life-skills training and access to recreational activities. In this population who tested HIV negative the majority said they had made life changes months before attending VCT. Counselling served to consolidate pre-test decisions about risk behaviour. Those testing HIV negative are underserved compared with those testing positive. We recommend that counselling for HIV should be de-linked from testing to encourage earlier attendance for counselling and that clients testing negative should receive more post-test support to help them remain HIV negative.

Surgeons' opinions and practice of informed consent in Nigeria.

PubMed

Ogundiran, Temidayo O; Adebamowo, Clement A

2010-12-01

Informed consent is perhaps more relevant to surgical specialties than to other clinical disciplines. Fundamental to this concept is the provision of relevant information for the patient to make an informed choice about a surgical intervention. The opinions of surgeons in Nigeria about informed consent in their practice were surveyed. A cross-sectional survey of surgeons in Nigeria was undertaken in 2004/5 using self-administered semistructured questionnaires. There were 102 respondents, 85.3% of whom were men and 58.8% were aged 31-40 years. 43.1% were consultants and 54.0% were surgical trainees. 27.4% were in surgical subspecialties, 26.5% in general surgery and 21.6% were obstetricians and gynaecologists. 54.9% agreed that sufficient information is not provided to patients while obtaining their consent for surgical procedures. They listed medicolegal reasons (70.6%), informing patients about benefits, risks and alternatives (64.7%) and hospital policy (50.0%) as some reasons for obtaining consent for surgical procedures. When patients decline to give consent for surgery, 84.3% of them thought that poor communication between surgeons and patients may be contributory. They identified taking a course in bioethics during surgical training and compulsory communication skills course as some ways to improve communication between surgeons and patients. Most Nigerian surgeons seemed to have a good knowledge of the informed consent requirements and process but fall short in practice. There is a need to improve the surgeon-patient relationship in line with modern exigencies to provide interactive environments for fruitful patient communication and involvement.

The impact of genital warts: loss of quality of life and cost of treatment in eight sexual health clinics in the UK.

PubMed

Woodhall, S C; Jit, M; Soldan, K; Kinghorn, G; Gilson, R; Nathan, M; Ross, J D; Lacey, C J N

2011-10-01

To estimate the loss of quality of life and cost of treatment associated with genital warts seen in sexual health clinics. A cross-sectional questionnaire study and case note review of individuals with genital warts, carried out in eight sexual health clinics in England and Northern Ireland. Individuals with genital warts attending the participating clinics were invited to take part in the questionnaire study. 895 participants were recruited. A separate sample of 370 participants who had attended a participating clinic with a first visit for a first or recurrent episode of genital warts between April and June 2007 was included in the case note review. Quality of life was measured using the EQ-5D questionnaire and the cost of an episode of care was derived from the case note review. The weighted mean EQ-5D index score was 0.87 (95% CI 0.85 to 0.89). The weighted mean disutility was 0.056 (95% CI 0.038 to 0.074). The estimated mean loss of quality-adjusted life-years associated with an episode of genital warts was 0.018 (95% CI 0.0079 to 0.031), equivalent to 6.6 days of healthy life lost per episode. The weighted mean cost per episode of care was £94 (95% CI £84 to £104), not including the cost of a sexually transmitted infection screen. Genital warts have a substantial impact on the health service and the individual. This information can be utilised for economic evaluation of human papillomavirus vaccination.

Microbial structures in an Alpine Thermal Spring - Microscopic techniques for the examination of Biofilms in a Subsurface Environment

NASA Astrophysics Data System (ADS)

Dornmayr-Pfaffenhuemer, Marion; Pierson, Elisabeth; Janssen, Geert-Jan; Stan-Lotter, Helga

2010-05-01

The research into extreme environments hast important implications for biology and other sciences. Many of the organisms found there provide insights into the history of Earth. Life exists in all niches where water is present in liquid form. Isolated environments such as caves and other subsurface locations are of interest for geomicrobiological studies. And because of their "extra-terrestrial" conditions such as darkness and mostly extreme physicochemical state they are also of astrobiological interest. The slightly radioactive thermal spring at Bad Gastein (Austria) was therefore examined for the occurrence of subsurface microbial communities. The surfaces of the submerged rocks in this warm spring were overgrown by microbial mats. Scanning electron microscopy (SEM) performed by the late Dr. Wolfgang Heinen revealed an interesting morphological diversity in biofilms found in this environment (1, 2). Molecular analysis of the community structure of the radioactive subsurface thermal spring was performed by Weidler et al. (3). The growth of these mats was simulated using sterile glass slides which were exposed to the water stream of the spring. Those mats were analysed microscopically. Staining, using fluorescent dyes such as 4',6-Diamidino-2-phenylindol (DAPI), gave an overview of the microbial diversity of these biofilms. Additional SEM samples were prepared using different fixation protocols. Scanning confocal laser microscopy (SCLM) allowed a three dimensional view of the analysed biofilms. This work presents some electron micrographs of Dr. Heinen and additionally new microscopic studies of the biofilms formed on the glass slides. The appearances of the new SEM micrographs were compared to those of Dr. Heinen that were done several years ago. The morphology and small-scale distribution in the microbial mat was analyzed by fluorescence microscopy. The examination of natural biomats and biofilms grown on glass slides using several microscopical techniques suggest that the thermal springs in the Central Alps near Bad Gastein represent a novel and unique habitat for microbial life. Results obtained during these studies revealed reproducibility of Dr. Heinen's micrographs. Hollow reticulated filaments and flat ribbons with parallel hexagonal chambers (web-structures) were found repeatedly. Given the chance that subsurface environments represent a potent opportunity to detect life on planetary bodies it is of big interest to search for representative biosignatures found on earth today. References: 1. Lauwers A. M. & Heinen W. (1985) Mikroskopie (Wien) 42, 94-101. 2. Heinen W. & Lauwers A. M. (1985) Mikroskopie (Wien) 42, 124-134. 3. Weidler G. W., Dornmayr-Pfaffenhuemer M., Gerbl F. W., Heinen W., Stan-Lotter H. (2007) AEM 73, 259-270.

An automated system for performing continuous viscosity versus temperature measurements of fluids using an Ostwald viscometer

NASA Astrophysics Data System (ADS)

Beaulieu, L. Y.; Logan, E. R.; Gering, K. L.; Dahn, J. R.

2017-09-01

An automated system was developed to measure the viscosity of fluids as a function of temperature using image analysis tracking software. An Ostwald viscometer was placed in a three-wall dewar in which ethylene glycol was circulated using a thermal bath. The system collected continuous measurements during both heating and cooling cycles exhibiting no hysteresis. The use of video tracking analysis software greatly reduced the measurement errors associated with measuring the time required for the meniscus to pass through the markings on the viscometer. The stability of the system was assessed by performing 38 consecutive measurements of water at 42.50 ± 0.05 °C giving an average flow time of 87.7 ± 0.3 s. A device was also implemented to repeatedly deliver a constant volume of liquid of 11.00 ± 0.03 ml leading to an average error in the viscosity of 0.04%. As an application, the system was used to measure the viscosity of two Li-ion battery electrolyte solvents from approximately 10 to 40 °C with results showing excellent agreement with viscosity values calculated using Gering's Advanced Electrolyte Model (AEM).

Cost-effectiveness of scaling up voluntary counselling and testing in West-Java, Indonesia.

PubMed

Tromp, Noor; Siregar, Adiatma; Leuwol, Barnabas; Komarudin, Dindin; van der Ven, Andre; van Crevel, Reinout; Baltussen, Rob

2013-01-01

to evaluate the costs-effectiveness of scaling up community-based VCT in West-Java. the Asian epidemic model (AEM) and resource needs model (RNM) were used to calculate incremental costs per HIV infection averted and per disability-adjusted life years saved (DALYs). Locally monitored demographic, epidemiological behavior and cost data were used as model input. scaling up community-based VCT in West-Java will reduce the overall population prevalence by 36% in 2030 and costs US$248 per HIV infection averted and US$9.17 per DALY saved. Cost-effectiveness estimation were most sensitive to the impact of VCT on condom use and to the population size of clients of female sex workers (FSWs), but were overall robust. The total costs for scaling up community-based VCT range between US$1.3 and 3.8 million per year and require the number of VCT integrated clinics at public community health centers to increase from 73 in 2010 to 594 in 2030. scaling up community-based VCT seems both an effective and cost-effective intervention. However, in order to prioritize VCT in HIV/AIDS control in West-Java, issues of budget availability and organizational capacity should be addressed.

The effects of heat treatment on the chromium depletion, precipitate evolution, and corrosion resistance of INCONEL alloy 690

NASA Astrophysics Data System (ADS)

Kai, J. J.; Yu, G. P.; Tsai, C. H.; Liu, M. N.; Yao, S. C.

1989-10-01

A series of heat treatments were performed to study the sensitization and the stress corrosion cracking (SCC) behavior of INCONEL Alloy 690. The microstructural evaluation and the chromium depletion near grain boundaries were carefully studied using analytical electron microscopy (AEM). The measured chromium depletion profiles were matched well to the calculated results from a thermodynamic/kinetic model. The constant extension rate test (CERT) was performed in the solution containing 0.001 M sodium thiosulfate (Na2S2O3) to study the SCC resistance of this alloy. The Huey test was also performed in a boiling 65 pct HNO3 solution for 48 hours to study the intergranular attack (IGA) resistance of this alloy. Both tests showed that INCONEL 690 has very good corrosion resistance. It is believed that the superior IGA and SCC resistances of this alloy are due to the high chromium concentration (≈30 wt pct). It is concluded in this study that INCONEL 690 may be a better alloy than INCONEL 600 for use as the steam generator (S/G) tubing material for pressurized water reactors (PWR's)

Electrocatalytic processing of renewable biomass-derived compounds for production of chemicals, fuels and electricity

NASA Astrophysics Data System (ADS)

Xin, Le

The dual problems of sustaining the fast growth of human society and preserving the environment for future generations urge us to shift our focus from exploiting fossil oils to researching and developing more affordable, reliable and clean energy sources. Human beings had a long history that depended on meeting our energy demands with plant biomass, and the modern biorefinery technologies realize the effective conversion of biomass to production of transportation fuels, bulk and fine chemicals so to alleviate our reliance on fossil fuel resources of declining supply. With the aim of replacing as much non-renewable carbon from fossil oils with renewable carbon from biomass as possible, innovative R&D activities must strive to enhance the current biorefinery process and secure our energy future. Much of my Ph.D. research effort is centered on the study of electrocatalytic conversion of biomass-derived compounds to produce value-added chemicals, biofuels and electrical energy on model electrocatalysts in AEM/PEM-based continuous flow electrolysis cell and fuel cell reactors. High electricity generation performance was obtained when glycerol or crude glycerol was employed as fuels in AEMFCs. The study on selective electrocatalytic oxidation of glycerol shows an electrode potential-regulated product distribution where tartronate and mesoxalate can be selectively produced with electrode potential switch. This finding then led to the development of AEMFCs with selective production of valuable tartronate or mesoxalate with high selectivity and yield and cogeneration of electricity. Reaction mechanisms of electrocatalytic oxidation of ethylene glycol and 1,2-propanediol were further elucidated by means of an on-line sample collection technique and DFT modeling. Besides electro-oxidation of biorenewable alcohols to chemicals and electricity, electrocatalytic reduction of keto acids (e.g. levulinic acid) was also studied for upgrading biomass-based feedstock to biofuels while achieving renewable electricity storage. Meanwhile, ORR that is often coupled in AEMFCs on the cathode was investigated on non-PGM electrocatalyst with comparable activity to commercial Pt/C. The electro-biorefinery process could be coupled with traditional biorefinery operation and will play a significant role in our energy and chemical landscape.

Gender-specific research for emergency diagnosis and management of ischemic heart disease: proceedings from the 2014 Academic Emergency Medicine Consensus Conference Cardiovascular Research Workgroup.

PubMed

Safdar, Basmah; Nagurney, John T; Anise, Ayodola; DeVon, Holli A; D'Onofrio, Gail; Hess, Erik P; Hollander, Judd E; Legato, Mariane J; McGregor, Alyson J; Scott, Jane; Tewelde, Semhar; Diercks, Deborah B

2014-12-01

Coronary artery disease (CAD) is the most common cause of death for both men and women. However, over the years, emergency physicians, cardiologists, and other health care practitioners have observed varying outcomes in men and women with symptomatic CAD. Women in general are 10 to 15 years older than men when they develop CAD, but suffer worse postinfarction outcomes compared to age-matched men. This article was developed by the cardiovascular workgroup at the 2014 Academic Emergency Medicine (AEM) consensus conference to identify sex- and gender-specific gaps in the key themes and research questions related to emergency cardiac ischemia care. The workgroup had diverse stakeholder representation from emergency medicine, cardiology, critical care, nursing, emergency medical services, patients, and major policy-makers in government, academia, and patient care. We implemented the nominal group technique to identify and prioritize themes and research questions using electronic mail, monthly conference calls, in-person meetings, and Web-based surveys between June 2013 and May 2014. Through three rounds of nomination and refinement, followed by an in-person meeting on May 13, 2014, we achieved consensus on five priority themes and 30 research questions. The overarching themes were as follows: 1) the full spectrum of sex-specific risk as well as presentation of cardiac ischemia may not be captured by our standard definition of CAD and needs to incorporate other forms of ischemic heart disease (IHD); 2) diagnosis is further challenged by sex/gender differences in presentation and variable sensitivity of cardiac biomarkers, imaging, and risk scores; 3) sex-specific pathophysiology of cardiac ischemia extends beyond conventional obstructive CAD to include other causes such as microvascular dysfunction, takotsubo, and coronary artery dissection, better recognized as IHD; 4) treatment and prognosis are influenced by sex-specific variations in biology, as well as patient-provider communication; and 5) the changing definitions of pathophysiology call for looking beyond conventionally defined cardiovascular outcomes to patient-centered outcomes. These emergency care priorities should guide future clinical and basic science research and extramural funding in an area that greatly influences patient outcomes. © 2014 by the Society for Academic Emergency Medicine.

Shallow Sub-Permafrost Groundwater Systems In A Buried Fjord: Taylor Valley, Antarctica

NASA Astrophysics Data System (ADS)

Foley, N.; Tulaczyk, S. M.; Auken, E.; Mikucki, J.

2014-12-01

The McMurdo Dry Valleys (MDV), Antarctica, represent a unique geologic setting where permanent lakes, ephemeral streams, and subglacial waters influence surface hydrology in a cold polar desert. Past research suggested that the MDV are underlain by several hundreds of meters of permafrost. Here, we present data collected from an Airborne EM (AEM) resistivity sensor flown over the MDV during the 2011-12 austral summer. A focus of our survey was over the Taylor Glacier where saline, iron-rich subglacial fluid releases at the glacier snout at a feature known as Blood Falls, and over Taylor Valley, where a series of isolated lakes lie between Taylor Glacier and the Ross Sea. Our data show that in Taylor Valley there are extensive areas of low resistivity, interpreted as hypersaline brines, beneath a relatively thin layer of high resistivity material, interpreted as dry- or ice-cemented permafrost. These hypersaline brines remain liquid at temperatures well below 0°C due to their salinity. They appear to be contained within the sedimentary fill deposited in Taylor Valley when it was still a fjord. This brine system continues up valley and has a subglacial extension beneath Taylor Glacier, where it may provide the source that feeds Blood Falls. By categorizing the resistivity measurements according to surficial land cover, we are able to distinguish between ice, permafrost, lake water, and seawater based on characteristic resistivity distributions. Furthermore, this technique shows that areas of surface permafrost become increasingly conductive (brine-filled) with depth, whereas the large lakes exhibit taliks that extend through the entire thickness of the permafrost. The subsurface brines represent a large, unstudied and potentially connected hydrogeologic system, in which subsurface flows may help transfer water and nutrients between lakes in the MDV and into the Ross Sea. Such a system is a potential habitat for extremophile life, similar to that already detected in the Blood Falls outflow, and may serve as a terrestrial analogue to potential extraterrestrial habits, where liquid surface waters are not expected to exist.

Gender inequality in the risk of violence: material deprivation is linked to higher risk for adolescent girls.

PubMed

Nasr, Inas; Sivarajasingam, Vaseekaran; Jones, Sarah; Shepherd, Jonathan

2010-11-01

To investigate the association between material deprivation and injury sustained in violence by adolescents aged 11-17 years. Computerised data relating to gender, attendance date and resident postcode of all patients aged 11-17 years who received treatment for violence-related injuries at seven emergency departments (ED) in South Wales over 12 months, 1 October 2005 to 30 September 2006, were studied. The resident populations, by electoral division of three unitary authorities in Wales, Cardiff, Swansea and Newport, were obtained from the NHS administrative register. The relationships between demographic variables and material deprivation as measured by the Townsend deprivation index were analysed. Altogether 699 (475 boys; 224 girls) adolescents aged 11-17 years resident in Cardiff, Swansea and Newport attended ED in South Wales following violence. Boys and girls living in the most deprived areas had higher assault injury rates compared with those living in the most affluent areas. In the context of sustaining violence-related injury, material deprivation affected girls aged 11-17 years to a much greater extent (Cardiff most deprived vs most affluent rate ratio 6.31, Swansea 10.11, Newport 2.90) than boys of the same age group (Cardiff most deprived vs most affluent rate ratio 2.02, Swansea 7.74, Newport 1.74). Material deprivation was associated with a higher risk of violence-related injury for adolescent girls compared with adolescent boys. Risk-taking behaviour for adolescent boys and girls may be different under different socioeconomic conditions. Violence prevention efforts should focus more on tackling neighbourhood inequalities, particularly those related to material deprivation in adolescent girls.

R-citalopram functionally antagonises escitalopram in vivo and in vitro: evidence for kinetic interaction at the serotonin transporter

PubMed Central

Stórustovu, Signe í; Sánchez, Connie; Pörzgen, Peter; Brennum, Lise T; Larsen, Anna Kirstine; Pulis, Monica; Ebert, Bjarke

2004-01-01

Clinical observations with the selective serotonin reuptake inhibitor (SSRI), S-citalopram, indicate that S-citalopram is more efficacious and produces earlier symptom relief than RS-citalopram. Since R-citalopram is at least 20-fold weaker than S-citalopram as inhibitor of the 5-HT transporter (SERT) in preclinical studies, the clinical data suggest an unexpected antagonistic interaction between the two enantiomers. We therefore characterised the interaction of R- and S-citalopram with the SERT in in vivo and in vitro assays. In both behavioural (potentiation of 5-hydroxytryptophan (5-HTP)-induced behaviour) and electrophysiological studies (inhibition of 5-HT-elicited ion currents in Xenopus oocytes expressing the human SERT (hSERT) R-citalopram inhibited the effects of S-citalopram in a dose-dependent manner. With S-citalopram : R-citalopram ratios of 1 : 2 and 1 : 4, 5-HTP potentiation was significantly smaller than with S-citalopram alone. emsp;R-citalopram did not antagonise the effects of another SSRI (fluoxetine) in either behavioural or electrophysiological studies. In oocytes, inhibition of hSERT-mediated currents by R-citalopram was almost completely reversible and characterised by fast on- and off-sets of action. In contrast, the off-set for S-citalopram was 35-fold slower than for R-citalopram. Kinetic analysis of the oocyte experiments suggests that S-citalopram binding to SERT induces a long-lasting, inhibited state of the transporter and that coapplication of R-citalopram partially relieves SERT of this persistent inhibition. We propose that the kinetic interaction of R- and S-citalopram with SERT is a critical factor contributing to the antagonistic effects of R-citalopram on S-citalopram in vitro and in vivo. PMID:15037515

ArgR is an essential local transcriptional regulator of the arcABC operon in Streptococcus suis and is crucial for biological fitness in an acidic environment.

PubMed

Fulde, Marcus; Willenborg, Joerg; de Greeff, Astrid; Benga, Laurentiu; Smith, Hilde E; Valentin-Weigand, Peter; Goethe, Ralph

2011-02-01

Streptococcus suis is one of the most important pathogens in pigs and can also cause severe infections in humans. Despite its clinical relevance, very little is known about the factors that contribute to its virulence. Recently, we identified a new putative virulence factor in S. suis, the arginine deiminase system (ADS), an arginine catabolic enzyme system encoded by the arcABC operon, which enables S. suis to survive in an acidic environment. In this study, we focused on ArgR, an ADS-associated regulator belonging to the ArgR/AhrC arginine repressor family. Using an argR knockout strain we were able to show that ArgR is essential for arcABC operon expression and necessary for the biological fitness of S. suis. By cDNA expression microarray analyses and quantitative real-time RT-PCR we found that the arcABC operon is the only gene cluster regulated by ArgR, which is in contrast to the situation in many other bacteria. Reporter gene analysis with gfp under the control of the arcABC promoter demonstrated that ArgR is able to activate the arcABC promoter. Electrophoretic mobility shift assays with fragments of the arcABC promoter and recombinant ArgR, and chromatin immunoprecipitation with antibodies directed against ArgR, revealed that ArgR interacts with the arcABC promoter in vitro and in vivo by binding to a region from -147 to -72 bp upstream of the transcriptional start point. Overall, our results show that in S. suis, ArgR is an essential, system-specific transcriptional regulator of the ADS that interacts directly with the arcABC promoter in vivo.

Variation in a surface-exposed region of the Mycoplasma pneumoniae P40 protein as a consequence of homologous DNA recombination between RepMP5 elements.

PubMed

Spuesens, Emiel B M; van de Kreeke, Nick; Estevão, Silvia; Hoogenboezem, Theo; Sluijter, Marcel; Hartwig, Nico G; van Rossum, Annemarie M C; Vink, Cornelis

2011-02-01

Mycoplasma pneumoniae is a human pathogen that causes a range of respiratory tract infections. The first step in infection is adherence of the bacteria to the respiratory epithelium. This step is mediated by a specialized organelle, which contains several proteins (cytadhesins) that have an important function in adherence. Two of these cytadhesins, P40 and P90, represent the proteolytic products from a single 130 kDa protein precursor, which is encoded by the MPN142 gene. Interestingly, MPN142 contains a repetitive DNA element, termed RepMP5, of which homologues are found at seven other loci within the M. pneumoniae genome. It has been hypothesized that these RepMP5 elements, which are similar but not identical in sequence, recombine with their counterpart within MPN142 and thereby provide a source of sequence variation for this gene. As this variation may give rise to amino acid changes within P40 and P90, the recombination between RepMP5 elements may constitute the basis of antigenic variation and, possibly, immune evasion by M. pneumoniae. To investigate the sequence variation of MPN142 in relation to inter-RepMP5 recombination, we determined the sequences of all RepMP5 elements in a collection of 25 strains. The results indicate that: (i) inter-RepMP5 recombination events have occurred in seven of the strains, and (ii) putative RepMP5 recombination events involving MPN142 have induced amino acid changes in a surface-exposed part of the P40 protein in two of the strains. We conclude that recombination between RepMP5 elements is a common phenomenon that may lead to sequence variation of MPN142-encoded proteins.

The effect of Sao Paulo's smoke-free legislation on carbon monoxide concentration in hospitality venues and their workers.

PubMed

Issa, Jaqueline S; Abe, Tania M O; Pereira, Alexandre C; Megid, Maria Cristina; Shimabukuro, Cristina E; Valentin, Luis Sergio O; Ferreira, Marizete M da C; Nobre, Moacyr R C; Lancarotte, Ines; Barretto, Antonio Carlos Pereira

2011-03-01

Studies have shown that there is no safe level of secondhand smoke (SHS) exposure and there is a close link between SHS and the risk of coronary heart disease and stroke. Carbon monoxide (CO) is one of the most important components present in SHS. To evaluate the impact of the smoking ban law in the city of Sao Paulo, Brazil, on the CO concentration in restaurants, bars, night clubs and similar venues and in their workers. In the present study we measured CO concentration in 585 hospitality venues. CO concentration was measured in different environments (indoor, semi-open and open areas) from visited venues, as well as, in the exhaled air from approximately 627 workers of such venues. Measurements were performed twice, before and 12 weeks after the law implementation. In addition, the quality of the air in the city during the same period of our study was verified. RESULTS The CO concentration pre-ban and pot-ban in hospitality venues was indoor area 4.57 (3.70) ppm vs 1.35 (1.66) ppm (p<0.0001); semi-open 3.79 (2.49) ppm vs 1.16 (1.14) ppm (p<0.0001); open area 3.31(2.2) ppm vs 1.31 (1.39) ppm (p<0.0001); smoking employees 15.78 (9.76) ppm vs 11.50 (7.53) ppm (p<0.0001) and non-smoking employees 6.88 (5.32) ppm vs 3.50 (2.21) ppm (p<0.0001). The average CO concentration measured in the city was lower than 1 ppm during both pre-ban and post-ban periods. São Paulo's smoking-free legislation reduced significantly the CO concentration in hospitality venues and in their workers, whether they smoke or not.

Professional values and reported behaviours of doctors in the USA and UK: quantitative survey.

PubMed

Roland, Martin; Rao, Sowmya R; Sibbald, Bonnie; Hann, Mark; Harrison, Stephen; Walter, Alex; Guthrie, Bruce; Desroches, Catherine; Ferris, Timothy G; Campbell, Eric G

2011-06-01

BACKGROUND The authors aimed to determine US and UK doctors' professional values and reported behaviours, and the extent to which these vary with the context of care. METHOD 1891 US and 1078 UK doctors completed the survey (64.4% and 40.3% response rate respectively). Multivariate logistic regression was used to compare responses to identical questions in the two surveys. RESULTS UK doctors were more likely to have developed practice guidelines (82.8% UK vs 49.6% US, p<0.001) and to have taken part in a formal medical error-reduction programme (70.9% UK vs 55.7% US, p<0.001). US doctors were more likely to agree about the need for periodic recertification (completely agree 23.4% UK vs 53.9% US, p<0.001). Nearly a fifth of doctors had direct experience of an impaired or incompetent colleague in the previous 3 years. Where the doctor had not reported the colleague to relevant authorities, reasons included thinking that someone else was taking care of the problem, believing that nothing would happen as a result, or fear of retribution. UK doctors were more likely than US doctors to agree that significant medical errors should always be disclosed to patients. More US doctors reported that they had not disclosed an error to a patient because they were afraid of being sued. DISCUSSION The context of care may influence both how professional values are expressed and the extent to which behaviours are in line with stated values. Doctors have an important responsibility to develop their healthcare systems in ways which will support good professional behaviour.

Non-monogamy: risk factor for STI transmission and acquisition and determinant of STI spread in populations.

PubMed

Aral, Sevgi O; Leichliter, Jami S

2010-12-01

The concept of concurrent partnerships, while theoretically appealing, has been challenged at many levels. However, non-monogamy may be an important risk factor for the acquisition and transmission of sexually transmitted infections (STI). One's own non-monogamy is a risk factor for transmitting STI to others, partners' non-monogamy is a risk factor for acquiring STI and, most importantly, mutual non-monogamy is a population level determinant of increased STI spread. This study describes the levels, distribution and correlates of non-monogamy, partners' non-monogamy and mutual non-monogamy among adult men and women in the USA. Data from the National Survey of Family Growth (NSFG) Cycle 6 were used. NSFG is a national household survey of subjects aged 15-44 years in the USA. Cochran-Mantel-Haenszel tests and χ(2) tests were used in the analysis. Among sexually active adults, 17.6% of women and 23.0% of men (an estimated 19 million) reported non-monogamy over the past 12 months in 2002. An estimated 11 million Americans (1 in 10) reported partners' non-monogamy and an estimated 8.4 million (7% of women and 10.5% of men) reported mutual non-monogamy. All three types of non-monogamy were reported more frequently by men than women. Younger age, lower education, formerly or never married status, living below the poverty level and having spent time in jail were associated with all three types of non-monogamy in general. The three types of non-monogamy may be helpful in tailoring prevention messages and targeting prevention efforts to subgroups most likely to spread infection.

The 2017 Academic Emergency Medicine Consensus Conference: Catalyzing System Change Through Healthcare Simulation: Systems, Competency, and Outcomes.

PubMed

Bond, William F; Hui, Joshua; Fernandez, Rosemarie

2018-02-01

Over the past decade, emergency medicine (EM) took a lead role in healthcare simulation in part due to its demands for successful interprofessional and multidisciplinary collaboration, along with educational needs in a diverse array of cognitive and procedural skills. Simulation-based methodologies have the capacity to support training and research platforms that model micro-, meso-, and macrosystems of healthcare. To fully capitalize on the potential of simulation-based research to improve emergency healthcare delivery will require the application of rigorous methods from engineering, social science, and basic science disciplines. The Academic Emergency Medicine (AEM) Consensus Conference "Catalyzing System Change Through Healthcare Simulation: Systems, Competency, and Outcome" was conceived to foster discussion among experts in EM, engineering, and social sciences, focusing on key barriers and opportunities in simulation-based research. This executive summary describes the overall rationale for the conference, conference planning, and consensus-building approaches and outlines the focus of the eight breakout sessions. The consensus outcomes from each breakout session are summarized in proceedings papers published in this issue of Academic Emergency Medicine. Each paper provides an overview of methodologic and knowledge gaps in simulation research and identifies future research targets aimed at improving the safety and quality of healthcare. © 2017 by the Society for Academic Emergency Medicine.

Analysis of alkaline exchange membrane fuel cells performance at different operating conditions using DC and AC methods

NASA Astrophysics Data System (ADS)

Reshetenko, Tatyana; Odgaard, Madeleine; Schlueter, Debbie; Serov, Alexey

2018-01-01

Membrane electrode assemblies (MEAs) for anion exchange membrane fuel cells (AEMFCs) were manufactured from commercial materials: Pt/C catalyst, A201 AEM and AS4 ionomer by using an industrial mass-production digital printing method. The MEA designs selected are close to those recommended by US Department of Energy, including low loading of platinum on the cathode side (0.2 mg cm-2). Polarization curves and electrochemical impedance spectroscopy (EIS) were applied for MEA evaluation in fuel cell conditions with variation of gas humidification and oxygen partial pressure (air vs oxygen). The typical impedance curves recorded at H2/O2 gas configuration consist of high- and medium-frequency arcs responsible for hydrogen oxidation and oxygen reduction, respectively. Operation with air as a cathode feed gas resulted in a decrease in AEMFC performance due to possible CO2 poisoning and mass transfer losses. At the same time, EIS demonstrated formation of a low frequency loop due to diffusion limitations. Despite the low loading of platinum on the cathode (0.2 mg cm-2), a peak power density of ∼330 mW cm-2 was achieved (at 50/50% of RH on anode and cathode), which is substantially higher performance than for AEMFC MEAs tested at similar conditions.

Development of composite membranes of PVA-TEOS doped KOH for alkaline membrane fuel cell

NASA Astrophysics Data System (ADS)

Haryadi, Sugianto, D.; Ristopan, E.

2015-12-01

Anion exchange membranes (AEMs) play an important role in separating fuel and oxygen (or air) in the Alkaline Membrane Fuel Cells. Preparation of hybrid organic inorganic materials of Polyvinylalcohol (PVA) - Tetraethylorthosilicate (TEOS) composite membrane doped KOH for direct alcohol alkaline fuel cell application has been investigated. The sol-gel method has been used to prepare the composite membrane of PVA-TEOS through crosslinking step and catalyzed by concentrated of hydrochloric acid. The gel solution was cast on the membrane plastic plate to obtain membrane sheets. The dry membranes were then doped by immersing in various concentrations of KOH solutions for about 4 hours. Investigations of the cross-linking process and the presence of hydroxyl group were conducted by FTIR as shown for frequency at about 1600 cm-1 and 3300 cm-1 respectively. The degree of swelling in ethanol decreased as the KOH concentration for membrane soaking process increased. The ion exchange capacity (IEC) of the membrane was 0.25meq/g. This composite membranes display significant ionic conductivity of 3.23 x 10-2 S/cm in deionized water at room temperature. In addition, the morphology observation by scanning electron microscope (SEM) of the membrane indicates that soaking process of membrane in KOH increased thermal resistant.

Analysis of cocaine/crack biomarkers in meconium by LC-MS.

PubMed

D'Avila, Felipe Bianchini; Ferreira, Pâmela C Lukasewicz; Salazar, Fernanda Rodrigues; Pereira, Andrea Garcia; Santos, Maíra Kerpel Dos; Pechansky, Flavio; Limberger, Renata Pereira; Fröehlich, Pedro Eduardo

2016-02-15

Fetal exposure to illicit drugs is a worldwide problem, since many addicted women do not stop using it during pregnancy. Cocaine consumed in powdered (snorted or injected) or smoked (crack cocaine) form are harmful for the baby and its side effects are not completely known. Meconium, the first stool of a newborn, is a precious matrix usually discarded, that may contain amounts of substances consumed in the last two trimesters of pregnancy. Analyzing this biological matrix it is possible to detect the unaltered molecule of cocaine (COC) or its metabolite benzoylecgonine (BZE) and pyrolytic products anhydroecgonine methyl ester (AEME) and anhydroecgonine (AEC). A liquid chromatography mass spectrometry (LC-MS) method was validated for meconium samples after solvent extraction, followed by direct injection of 10μL. Linearity covered a concentration range of 15 to 500ng/mg with a lower limit of quantification (LLOQ) of 15ng/mg for all analytes. Matrix effect was evaluated and showed adequate results. Detection of illicit substances usage can be crucial for the baby, since knowing that can help provide medical care as fast as possible. The method proved to be simple and fast, and was applied to 17 real meconium samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Magnetic nanoparticles and thermally responsive polymer for targeted hyperthermia and sustained anti-cancer drug delivery.

PubMed

Wang, Sarah Y; Liu, Michelle C; Kang, Kyung A

2013-01-01

A novel cancer treatment method is being designed using a combination of iron oxide (Fe(3)O(4)) nanoparticles (IONPs) and Pluronic F-127 (PF127). IONPs have been used for heating tumors via an alternating electromagnetic (AEM) field. PF127 is a polymer possessing thermo-reversible and concentration-dependent gelation properties in aqueous solutions. PF127, as a gel, is an attractive drug delivery vehicle due to its zero-order drug release property. The combination of IONPs and PF127 would allow both short-term, tumor-specific, hyperthermic treatment, and long-term sustained drug delivery. As a preliminary study, the gelling and heating properties of IONPs/PF127 mixtures were investigated: 18% (w/w) PF127 was found to be ideal for our purpose because it gels at 28.0°C, i.e., it would be injectable at room temperature (20-25°C) and forms gel upon injection into the body (37°C). IONPs in PF127 showed little effect on gelation temperatures. The heating performance of IONPs in PF127 slightly, but linearly decreased with PF127. In the IONP concentration range of 0.01-0.05% (w/v) mixed with PF127 at 18% (w/w), the heating performance increased linearly with the increase in IONP concentration.

An aqueous all-organic redox-flow battery employing a (2,2,6,6-tetramethylpiperidin-1-yl)oxyl-containing polymer as catholyte and dimethyl viologen dichloride as anolyte

NASA Astrophysics Data System (ADS)

Hagemann, Tino; Winsberg, Jan; Grube, Mandy; Nischang, Ivo; Janoschka, Tobias; Martin, Norbert; Hager, Martin D.; Schubert, Ulrich S.

2018-02-01

Herein we present a new redox-flow battery (RFB) that employs a (2,2,6,6-tetramethylpiperidin-1-yl)oxyl (TEMPO) containing copolymer (P1) as catholyte and the viologen derivative N,N‧-dimethyl-4,4‧-bipyridinium dichloride (MV) as anolyte in an aqueous sodium chloride solution. This is the first time that a combination of an organic polymer and a low-molar-mass organic redox-active material is presented. The electrochemical behavior of the utilized charge-storage materials were investigated by cyclic voltammetry (CV) and feature reversible redox-reactions at E½ = 0.7 V (TEMPO/TEMPO+) and E½ = -0.6 V vs. AgCl/Ag (MV++/MV+•), which lead to a promising cell voltage of 1.3 V in the subsequent battery application. Studies were performed to determine the most suitable anion-exchange membrane (AEM), the ideal conducting salt concentration and the optimal flow rate. The resulting battery reveals a stable charge/discharge performance over 100 consecutive cycles with coulombic efficiencies of up to 95%, a high energy efficiency of 85% and an overall energy density of the electrolyte system of 3.8 W h L-1.

A series of poly(butylimidazolium) ionic liquid functionalized copolymers for anion exchange membranes

NASA Astrophysics Data System (ADS)

Ouadah, Amina; Xu, Hulin; Luo, Tianwei; Gao, Shuitao; Wang, Xing; Fang, Zhou; Jing, Chaojun; Zhu, Changjin

2017-12-01

A new series of ionic liquid functionalized copolymers for anion exchange membranes (AEM) is prepared. Poly(butylvinylimidazolium)(b-VIB) is copolymerized with para-methyl styrene (p-MS) by the radical polymerization formed block copolymers b-VIB/p-MS, which is crosslinked with poly(diphenylether bibenzimidazole) (DPEBI) providing the desired materials b-VIB/p-MS/DPEBI. Structures are characterized via H1NMR, FTIR spectra and elemental analysis. The b-VIB blocks offer the anion conduction function while DPEBI moieties contribute to enhancing other properties. The prepared membranes display chloride conductivity as high as 19.5 mS/cm at 25 °C and 69.2 mS/cm at 100 °C-higher than that of the commercial membrane tokuyuama A201-. Their hydroxide conductivity reaches 35.7 Scm-1 at 25 °C and 73.1 Scm-1 at 100 °C. The membranes showed a linear Arrhenius behavior in the anion conduction, low activation energies and distinguished nanophase separation of hydrophilic/hydrophobic regions by the transmission electron microscopy (TEM) studies. Thermal investigations using TGA and DSC confirm that the membranes are stable up to 250 °C. Particularly, drastically alkaline stability due to no decrease in the hydroxide conductivity after 168 h of treatment with 2M KOH.

Advanced processing of airborne FDEM data for improved imaging of groundwater conduits and sea water layering near Tulum, Mexico

NASA Astrophysics Data System (ADS)

Schiller, Arnulf; Schattauer, Ingrid; Supper, Robert; Motschka, Klaus; Alonso Merediz, Gonzalo; Lopez Tamayo, Alejandro

2017-04-01

The study presented herein is part of a series of international research cooperations, started in the year 2006 and still ongoing, which have the general objective to develop and test new approaches of data acquisition and modelling methods for studying a complex ground/seawater regime and its interaction. The study area is located at the Yucatan Peninsula, Mexico, and comprises the northern most part of the Sian Ka'an biosphere reserve, a coastal wetland of international recognition, as well as the town of Tulum and part of the worlds second largest barrier reef. In the subsurface, and below the city, the whole area is nerved by a complex network of underwater caves. The upper most fresh water layer of the karstic aquifer actually represents the only significant fresh water resource in the region. In principle, karst aquifers are characterized by the presence of two distinct flow domains: the limestone matrix and the karst conduits. A flow model of karst aquifers requires detailed, spatially distributed information on the characteristics of the two domains. Electromagnetic methods determining the distribution of the electrical resistivity within the subsurface can provide such information. To explore the applicability of airborne electromagnetics, several airborne surveys in the area were conducted in 2007, 2008, and 2015 by the Geological Survey of Austria, covering an area of some 300 square kilometres in total. Above the reef, data has been acquired along distinct flight lines. Adapted and new processing techniques retrieved increased resolution of apparent electrical resistivity anomalies. These can be interpreted as vast complex conduit network inland partially confirmed by explored cave systems. Consequentely, a 3d-model of the network as well as complex halocline table and further aquifer structures have been derived. Furthermore, advanced processing of offshore lines delivered improved resolution of seawater layering primarily due to variation in temperature and/or salinity down to depths below skin depth. This recommends the AEM-method also for oceanographic studies concerning the most significant upper ocean layer and ocean/atmospheric interaction. Advanced data processing and numerical simulations show the opportunities of a common airborne FDEM system without specific hardware adaptions in hydrogeological studies encouraging further development including decoupled transmitter/receiver configuration as well as squid-sensors and adapted data processing.

Effect of Pendant Side-Chain Sterics and Dipole Forces on Short Range Ordering in Random Polyelectrolytes

NASA Astrophysics Data System (ADS)

Nwosu, Chinomso; Pandey, Tara; Herring, Andrew; Coughlin, Edward; University of Massachusetts, Amherst Collaboration; Colorado School of Mines Collaboration

Backbone-to-backbone spacing in polymers is known to be dictated by the length of the pendant side-chains. Dipole forces in random polyelectrolytes lead to ionic clusters with a characteristic spacing that can be observed by SAXS. Repulsion due to side-chain sterics will compete with dipole forces driving cluster formation in random polyelectrolytes. A model study on short range order in anion exchange membranes (AEMs) of quaternized P4VP-ran-PI is presented. Quaternization of P4VP with alkyl bromides having different numbers of carbons, CnBr, introduces pendant side-chains as well as charges. X-ray scattering performed on PQ4VP-ran-PI(CnBr) show that when n <5 the dipole forces dominate leading to the formation of ionic clusters. However, when n >4, the chains remain separated due to sterics, forming a distinct backbone-to-backbone spacing morphology. For n=3, both dipole clustering and backbone spacing can coexist. Crosslinking of the isoprene units increased the coexistence window from n=3 to n=6. Impedance measurements show that a maximum conductivity of 110mS/cm was obtained for PQ4VP-ran-PI(C3Br). A discussion on short range order due to competition, or counter balancing, of steric repulsion and dipole forces will be presented. US Army MURI project (W911NF1010520).

Analysis of prestressed concrete slab-and-beam structures

NASA Astrophysics Data System (ADS)

Sapountzakis, E. J.; Katsikadelis, J. T.

In this paper a solution to the problem of prestressed concrete slab-and-beam structures including creep and shrinkage effect is presented. The adopted model takes into account the resulting inplane forces and deformations of the plate as well as the axial forces and deformations of the beam, due to combined response of the system. The analysis consists in isolating the beams from the plate by sections parallel to the lower outer surface of the plate. The forces at the interface, which produce lateral deflection and inplane deformation to the plate and lateral deflection and axial deformation to the beam, are established using continuity conditions at the interface. The influence of creep and shrinkage effect relative with the time of the casting and the time of the loading of the plate and the beams is taken into account. The estimation of the prestressing axial force of the beams is accomplished iteratively. Both instant (e.g. friction, slip of anchorage) and time dependent losses are encountered. The solution of the arising plate and beam problems, which are nonlinearly coupled, is achieved using the analog equation method (AEM). The adopted model, compared with those ignoring the inplane forces and deformations, describes better the actual response of the plate-beams system and permits the evaluation of the shear forces at the interfaces, the knowledge of which is very important in the design of prefabricated ribbed plates.

Molecular Features of Wheat Endosperm Arabinoxylan Inclusion in Functional Bread

PubMed Central

Li, Weili; Hu, Hui; Wang, Qi; Brennan, Charles J.

2013-01-01

Arabinoxylan (AX) is a major dietary fibre component found in a variety of cereals. Numerous health benefits of arabinoxylans have been reported to be associated with their solubility and molecular features. The current study reports the development of a functional bread using a combination of AX-enriched material (AEM) and optimal commercial endoxylanase. The total AX content of bread was increased to 8.2 g per 100 g available carbohydrates. The extractability of AX in breads with and without endoxylanase was determined. The results demonstrate that water-extractable AX (WE-AX) increased progressively through the bread making process. The application of endoxylanase also increased WE-AX content. The presence of 360 ppm of endoxylanase had positive effects on the bread characteristics in terms of bread volume and firmness by converting the water unextractable (WU)-AX to WE-AX. In addition, the molecular weight (Mw) distribution of the WE-AX of bread with and without endoxylanase was characterized by size-exclusion chromatography. The results show that as the portion of WE-AX increased, the amount of high Mw WE-AX (higher than 100 kDa) decreased, whereas the amount of low Mw WE-AX (lower than 100 kDa) increased from 33.2% to 44.2% through the baking process. The low Mw WE-AX further increased to 75.5% with the application of the optimal endoxylanase (360 ppm). PMID:28239111

Recent progress on exploring exceptionally high and anisotropic H+/OH– ion conduction in two-dimensional materials

PubMed Central

Sun, Pengzhan; Sasaki, Takayoshi

2017-01-01

Ion conducting membranes/electrolytes have been employed extensively in some important industrial and biological systems, especially in fuel cells, water electrolyzers, gas separation, sensors and biological selective ion transport, acting as one of the core components and sometimes directly determining the device performance. However, the traditional polymeric proton exchange membranes (PEMs)/anion exchange membranes (AEMs) suffer from highly toxic preparation procedures, poor thermal and chemical stabilities, and unsatisfactory ion conductivities. This has triggered researchers worldwide to explore alternative inorganic building blocks with high ion conductivities and stabilities from the new materials library, hoping to solve the above long-lasting problems. The recent burgeoning research on two-dimensional (2D) materials has unveiled exceptionally high ionic conductivities, which raises the feasibility of fabricating high-performance nanosheet-based ion conductors/membranes. In this perspective, the recent advances in measuring and understanding the exceptionally high and anisotropic H+/OH– ion conductivities of representative 2D materials, e.g. graphene oxide (GO), vermiculite and layered double hydroxide (LDH) nanosheets, are reviewed. In particular, regarding the anisotropic ionic conduction in 2D nanosheets, possible design strategies and technological innovations for fabricating macroscopic nanosheet-based ionic conductors/membranes are proposed for maximizing the high in-plane conduction, which may serve to guide future development of high-performance industrial and biological systems relying on H+/OH– conducting membranes. PMID:29629071

Recent progress on exploring exceptionally high and anisotropic H+/OH- ion conduction in two-dimensional materials.

PubMed

Sun, Pengzhan; Ma, Renzhi; Sasaki, Takayoshi

2018-01-07

Ion conducting membranes/electrolytes have been employed extensively in some important industrial and biological systems, especially in fuel cells, water electrolyzers, gas separation, sensors and biological selective ion transport, acting as one of the core components and sometimes directly determining the device performance. However, the traditional polymeric proton exchange membranes (PEMs)/anion exchange membranes (AEMs) suffer from highly toxic preparation procedures, poor thermal and chemical stabilities, and unsatisfactory ion conductivities. This has triggered researchers worldwide to explore alternative inorganic building blocks with high ion conductivities and stabilities from the new materials library, hoping to solve the above long-lasting problems. The recent burgeoning research on two-dimensional (2D) materials has unveiled exceptionally high ionic conductivities, which raises the feasibility of fabricating high-performance nanosheet-based ion conductors/membranes. In this perspective, the recent advances in measuring and understanding the exceptionally high and anisotropic H + /OH - ion conductivities of representative 2D materials, e.g. graphene oxide (GO), vermiculite and layered double hydroxide (LDH) nanosheets, are reviewed. In particular, regarding the anisotropic ionic conduction in 2D nanosheets, possible design strategies and technological innovations for fabricating macroscopic nanosheet-based ionic conductors/membranes are proposed for maximizing the high in-plane conduction, which may serve to guide future development of high-performance industrial and biological systems relying on H + /OH - conducting membranes.

Wavelet-based 3-D inversion for frequency-domain airborne EM data

NASA Astrophysics Data System (ADS)

Liu, Yunhe; Farquharson, Colin G.; Yin, Changchun; Baranwal, Vikas C.

2018-04-01

In this paper, we propose a new wavelet-based 3-D inversion method for frequency-domain airborne electromagnetic (FDAEM) data. Instead of inverting the model in the space domain using a smoothing constraint, this new method recovers the model in the wavelet domain based on a sparsity constraint. In the wavelet domain, the model is represented by two types of coefficients, which contain both large- and fine-scale informations of the model, meaning the wavelet-domain inversion has inherent multiresolution. In order to accomplish a sparsity constraint, we minimize an L1-norm measure in the wavelet domain that mostly gives a sparse solution. The final inversion system is solved by an iteratively reweighted least-squares method. We investigate different orders of Daubechies wavelets to accomplish our inversion algorithm, and test them on synthetic frequency-domain AEM data set. The results show that higher order wavelets having larger vanishing moments and regularity can deliver a more stable inversion process and give better local resolution, while the lower order wavelets are simpler and less smooth, and thus capable of recovering sharp discontinuities if the model is simple. At last, we test this new inversion algorithm on a frequency-domain helicopter EM (HEM) field data set acquired in Byneset, Norway. Wavelet-based 3-D inversion of HEM data is compared to L2-norm-based 3-D inversion's result to further investigate the features of the new method.

Microbial desalination cell with sulfonated sodium poly(ether ether ketone) as cation exchange membranes for enhancing power generation and salt reduction.

PubMed

Moruno, Francisco Lopez; Rubio, Juan E; Atanassov, Plamen; Cerrato, José M; Arges, Christopher G; Santoro, Carlo

2018-06-01

Microbial desalination cell (MDC) is a bioelectrochemical system capable of oxidizing organics, generating electricity, while reducing the salinity content of brine streams. As it is designed, anion and cation exchange membranes play an important role on the selective removal of ions from the desalination chamber. In this work, sulfonated sodium (Na + ) poly(ether ether ketone) (SPEEK) cation exchange membranes (CEM) were tested in combination with quaternary ammonium chloride poly(2,6-dimethyl 1,4-phenylene oxide) (QAPPO) anion exchange membrane (AEM). Non-patterned and patterned (varying topographical features) CEMs were investigated and assessed in this work. The results were contrasted against a commercially available CEM. This work used real seawater from the Pacific Ocean in the desalination chamber. The results displayed a high desalination rate and power generation for all the membranes, with a maximum of 78.6±2.0% in salinity reduction and 235±7mWm -2 in power generation for the MDCs with the SPEEK CEM. Desalination rate and power generation achieved are higher with synthesized SPEEK membranes when compared with an available commercial CEM. An optimized combination of these types of membranes substantially improves the performances of MDC, making the system more suitable for real applications. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Development of composite membranes of PVA-TEOS doped KOH for alkaline membrane fuel cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haryadi,, E-mail: haryadi@polban.ac.id; Sugianto, D.; Ristopan, E.

2015-12-29

Anion exchange membranes (AEMs) play an important role in separating fuel and oxygen (or air) in the Alkaline Membrane Fuel Cells. Preparation of hybrid organic inorganic materials of Polyvinylalcohol (PVA) - Tetraethylorthosilicate (TEOS) composite membrane doped KOH for direct alcohol alkaline fuel cell application has been investigated. The sol-gel method has been used to prepare the composite membrane of PVA-TEOS through crosslinking step and catalyzed by concentrated of hydrochloric acid. The gel solution was cast on the membrane plastic plate to obtain membrane sheets. The dry membranes were then doped by immersing in various concentrations of KOH solutions for aboutmore » 4 hours. Investigations of the cross-linking process and the presence of hydroxyl group were conducted by FTIR as shown for frequency at about 1600 cm{sup −1} and 3300 cm{sup −1} respectively. The degree of swelling in ethanol decreased as the KOH concentration for membrane soaking process increased. The ion exchange capacity (IEC) of the membrane was 0.25meq/g. This composite membranes display significant ionic conductivity of 3.23 x 10{sup −2} S/cm in deionized water at room temperature. In addition, the morphology observation by scanning electron microscope (SEM) of the membrane indicates that soaking process of membrane in KOH increased thermal resistant.« less

Successful application of frequency-domain airborne electromagnetic system with a grounded electric source

NASA Astrophysics Data System (ADS)

Kang, L.; Lin, J.; Liu, C.; Zhou, H.; Ren, T.; Yao, Y.

2017-12-01

A new frequency-domain AEM system with a grounded electric source, which was called ground-airborne frequency-domain electromagnetic (GAFEM) system, was proposed to extend penetration depth without compromising the resolution and detection efficiency. In GAFEM system, an electric source was placed on the ground to enlarge the strength of response signals. UVA was chosen as aircraft to reduce interaction noise and improve its ability to adapt to complex terrain. Multi-source and multi-frequency emission method has been researched and applied to improve the efficiency of GAFEM system. 2n pseudorandom sequence was introduced as transmitting waveform, to ensure resolution and detection efficiency. Inversion-procedure based on full-space apparent resistivity formula was built to realize GAFEM method and extend the survey area to non-far field. Based on GAFEM system, two application was conducted in Changchun, China, to map the deep conductive structure. As shown in the results of this exploration, GAFEM system shows its effectiveness to conductive structure, obtaining a depth of about 1km with a source-receiver distance of over 6km. And it shows the same level of resolution with CSAMT method with an over 10 times of efficiency. This extended a range of important applications where the terrain is too complex to be accessed or large penetration depth is required in a large survey area.

Quasi-minimal active disturbance rejection control of MIMO perturbed linear systems based on differential neural networks and the attractive ellipsoid method.

PubMed

Salgado, Iván; Mera-Hernández, Manuel; Chairez, Isaac

2017-11-01

This study addresses the problem of designing an output-based controller to stabilize multi-input multi-output (MIMO) systems in the presence of parametric disturbances as well as uncertainties in the state model and output noise measurements. The controller design includes a linear state transformation which separates uncertainties matched to the control input and the unmatched ones. A differential neural network (DNN) observer produces a nonlinear approximation of the matched perturbation and the unknown states simultaneously in the transformed coordinates. This study proposes the use of the Attractive Ellipsoid Method (AEM) to optimize the gains of the controller and the gain observer in the DNN structure. As a consequence, the obtained control input minimizes the convergence zone for the estimation error. Moreover, the control design uses the estimated disturbance provided by the DNN to obtain a better performance in the stabilization task in comparison with a quasi-minimal output feedback controller based on a Luenberger observer and a sliding mode controller. Numerical results pointed out the advantages obtained by the nonlinear control based on the DNN observer. The first example deals with the stabilization of an academic linear MIMO perturbed system and the second example stabilizes the trajectories of a DC-motor into a predefined operation point. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Computer model for characterizing, screening, and optimizing electrolyte systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gering, Kevin L.

2015-06-15

Electrolyte systems in contemporary batteries are tasked with operating under increasing performance requirements. All battery operation is in some way tied to the electrolyte and how it interacts with various regions within the cell environment. Seeing the electrolyte plays a crucial role in battery performance and longevity, it is imperative that accurate, physics-based models be developed that will characterize key electrolyte properties while keeping pace with the increasing complexity of these liquid systems. Advanced models are needed since laboratory measurements require significant resources to carry out for even a modest experimental matrix. The Advanced Electrolyte Model (AEM) developed at themore » INL is a proven capability designed to explore molecular-to-macroscale level aspects of electrolyte behavior, and can be used to drastically reduce the time required to characterize and optimize electrolytes. Although it is applied most frequently to lithium-ion battery systems, it is general in its theory and can be used toward numerous other targets and intended applications. This capability is unique, powerful, relevant to present and future electrolyte development, and without peer. It redefines electrolyte modeling for highly-complex contemporary systems, wherein significant steps have been taken to capture the reality of electrolyte behavior in the electrochemical cell environment. This capability can have a very positive impact on accelerating domestic battery development to support aggressive vehicle and energy goals in the 21st century.« less

Cloning and expression of SgCYP450-4 from Siraitia grosvenorii.

PubMed

Tu, Dongping; Ma, Xiaojun; Zhao, Huan; Mo, Changming; Tang, Qi; Wang, Liuping; Huang, Jie; Pan, Limei

2016-11-01

CYP450 plays an essential role in the development and growth of the fruits of Siraitia grosvenorii . However, little is known about the SgCYP450-4 gene in S. grosvenorii . Here, based on transcriptome data, a full-length cDNA sequence of SgCYP450-4 was cloned by reverse transcriptase-polymerase chain reaction (RT-PCR) and rapid-amplification of cDNA ends (RACE) strategies. SgCYP450-4 is 1677 bp in length (GenBank accession No. AEM42985.1) and contains a complete open reading frame (ORF) of 1422 bp. The deduced protein was composed of 473 amino acids, the molecular weight is 54.01 kDa, the theoretical isoelectric point (PI) is 8.8, and the protein was predicted to possess cytochrome P450 domains. SgCYP450-4 gene was highly expressed in root, diploid fruit and fruit treated with hormone and pollination. At 10 days after treatment with pollination and hormones, the expression of Sg CYP450-4 had the highest level and then decreased over time, which was consistent with the development of fruits of S. Grosvenorii . Hormonal treatment could significantly induce the expression of SgCYP450-4 . These results provide a reference for regulation of fruit development and the use of parthenocarpy to generate seedless fruit, and provide a scientific basis for the production of growth regulator application agents.

Mine dewatering and impact assessment in an arid area: Case of Gulf region.

PubMed

Yihdego, Yohannes; Drury, Len

2016-11-01

Analytical and empirical solution coupled with water balance method were used to predict the ground water inflow to a mine pit excavated below the water table, final pit lake level/recovery and radius of influence, through long-term and time variant simulations. The solution considers the effect of decreased saturated thickness near the pit walls, distributed recharge to the water table and upward flow through the pit bottom. The approach is flexible to accommodate the anisotropy/heterogeneity of the real world. Final pit void water level was assessed through scenarios to know whether it will be consumed by evaporation and a shallow lake will form or not. The optimised radius of influence was estimated which is considered as crucial information in relation to the engineering aspects of mine planning and sustainable development of the mine area. Time-transient inflow over a period of time was estimated using solutions, including analytical element method (AEM). Their primary value is in providing estimates of pit inflow rates to be used in the mine dewatering. Inflow estimation and recovery helps whether there is water to supplement the demand and if there is any recovery issue to be dealt with in relation to surface and groundwater quality/eco-system, environmental evaluations and mitigation. Therefore, this method is good at informing decision makers in assessing the effects of mining operations and developing an appropriate water management strategy.

Small Scale Biodiversity of an Alkaline Hot Spring in Yellowstone National Park

NASA Astrophysics Data System (ADS)

Walther, K.; Oiler, J.; Meyer-Dombard, D. R.

2012-12-01

To date, many phylogenetic diversity studies have been conducted in Yellowstone National Park (YNP) [1-7] focusing on the amplification of the 16S rRNA gene and "metagenomic" datasets. However, few reports focus on diversity at small scales. Here, we report on a small scale biodiversity study of sediment and biofilm communities within a confined area of a YNP hot spring, compare and contrast these communities to other sediment and biofilm communities from previous studies [1-7], and with other sediment and biofilm communities in the same system. Sediment and biofilm samples were collected, using a 30 x 50 cm sampling grid divided in 5 x 5 cm squares, which was placed in the outflow channel of "Bat Pool", an alkaline (pH 7.9) hot spring in YNP. Accompanying geochemical data included a full range of spectrophotometry measurements along with major ions, trace elements, and DIC/DOC. In addition, in situ temperature and conductivity arrays were placed within the grid location. The temperature array closest to the source varied between 83-88°C, while the temperature array 40 cm downstream varied between ~83.5-86.5°C. The two conductivity arrays yielded measurements of 5632 μS and 5710 μS showing little variation within the sampling area. Within the grid space, DO ranged from 0.5-1.33 mg/L, with relatively similar, but slightly lower values down the outflow channel. Sulfide values within the grid ranged from 1020-1671 μg/L, while sulfide values outside of the grid region fluctuated, but generally followed the trend of decreasing from source down the outflow. Despite the relative heterogeneity of chemical and physical parameters in the grid space, there was biological diversity in sediments and biofilms at the 5 cm scale. Small scale biodiversity was analyzed by selecting a representative number of samples from within the grid. DNA was extracted and variable regions V3 and V6 (Archaea and Bacteria, respectively) were sequenced with 454 pyrosequencing. The datasets from each of the samples were randomly subsampled and the same number of sequences was taken from each dataset so that the samples could be directly compared. Using the Ribosomal Database Project Pyrosequencing Pipeline (http://rdp.cme.msu.edu/), the sequences were aligned, complete linkage clustering was performed, Shannon and Chao1 indices were calculated, and rarefaction curves were made. The RDP Classifier tool afforded classification in a taxonomical hierarchy and the samples were compared on the order level to determine the variation of the microbial communities within the sampling grid. Additional alpha and beta diversity indices were also established. Through comparing the samples on the order level, it was determined that there is variation within a small sampling area despite similar geochemical and temperature conditions at the time of sampling. This variation is seen in both the sediment and biofilm communities, primarily seen among Bacteria. [1] Barns, S.M. et al. (1994) PNAS. 91: 1609-1613. [2] Barns, S.M. et al. (1996) PNAS. 93: 9188-9193. [3] Hall, J.R. et al. (2008) AEM. 74(15): 4910-4922. [4] Hugenholtz, P. et al. (1998) JofBac. 180(2): 366-376. [5] Meyer-Dombard, D. R. et al. (2005) Geobio. 3: 211-227. [6] Meyer-Dombard, D.R. et al. (2011) EM. 13(8): 2216-2231. [7] Reysenbach, A.L. et al. (1994) AEM. 60 (6): 2113-2119.

Assessing the impacts of climate change and nitrogen deposition on Norway spruce (Picea abies L. Karst) growth in Austria with BIOME-BGC.

PubMed

Eastaugh, Chris S; Pötzelsberger, Elisabeth; Hasenauer, Hubert

2011-03-01

The aim of this paper is to determine whether a detectable impact of climate change is apparent in Austrian forests. In regions of complex terrain such as most of Austria, climatic trends over the past 50 years show marked geographic variability. As climate is one of the key drivers of forest growth, a comparison of growth characteristics between regions with different trends in temperature and precipitation can give insights into the impact of climatic change on forests. This study uses data from several hundred climate recording stations, interpolated to measurement sites of the Austrian National Forest Inventory (NFI). Austria as a whole shows a warming trend over the past 50 years and little overall change in precipitation. The warming trends, however, vary considerably across certain regions and regional precipitation trends vary widely in both directions, which cancel out on the national scale These differences allow the delineation of 'climatic change zones' with internally consistent climatic trends that differ from other zones. This study applies the species-specific adaptation of the biogeochemical model BIOME-BGC to Norway spruce (Picea abies (L.) Karst) across a range of Austrian climatic change zones, using input data from a number of national databases. The relative influence of extant climate change on forest growth is quantified, and compared with the far greater impact of non-climatic factors. At the national scale, climate change is found to have negligible effect on Norway spruce productivity, due in part to opposing effects at the regional level. The magnitudes of the modeled non-climatic influences on aboveground woody biomass increment increases are consistent with previously reported values of 20-40 kg of added stem carbon sequestration per kilogram of additional nitrogen deposition, while climate responses are of a magnitude difficult to detect in NFI data.

Anaemia in rheumatoid arthritis: can we afford to ignore it?

PubMed

Bloxham, E; Vagadia, V; Scott, K; Francis, G; Saravanan, V; Heycock, C; Rynne, M; Hamilton, J; Kelly, C A

2011-09-01

INTRODUCTION Anaemia is common in rheumatoid arthritis (RA). Clinicians may focus on rheumatological issues and assume anaemia of chronic disease (ACD). This study challenged this assumption and investigated the causes of anaemia in a large cohort of RA patients to assess its implications. METHODS The hospital where the study was conducted monitors regular full blood count and erythrocyte sedimentation rate (ESR) monthly in all RA patients on disease modifying drugs to assess efficacy and safety. A computerised system identifies and records abnormal results. The database for 2009 was interrogated to find all patients with two consecutive haemoglobin values <11 g/dl. Using a proforma, patients were defined as having iron deficiency anaemia (IDA), ACD, macrocytic anaemia (MCA) or another cause. All results of further tests investigating the anaemia were recorded. RESULTS Among 2000 RA patients on the system, 199 (10%) were identified as having anaemia over a year. Of these, 90 had IDA, 78 had ACD, 25 had MCA, and 6 had postoperative anaemia. Among 90 patients with IDA, investigations were performed in 53, with 23 normal. An explanation for IDA was found in 30: gastrointestinal bleeding in 25, gynaecological blood loss in 3, and urinary bleeding in 2. Among 78 patients with ACD, response to intensification of RA treatment occurred in 45, but erythropoietin therapy was required in 9. Within the 25 patients with MCA, 12 had unrecognised vitamin B(12) deficiency, 4 drug induced changes, 3 myeloid malignancy, 2 hypothyroidism, and 2 alcoholism. CONCLUSIONS Anaemia in RA is common, multifactorial, and potentially both serious and correctable. Established malignancy was present in 10 patients and premalignancy in a further 10 (10% of total). Treatable causes were commonly identified. Clinicians need to investigate the nature and cause of persistent anaemia, and must not assume it to be simply ACD without evidence.

Obesity is associated with fatal coronary heart disease independently of traditional risk factors and deprivation.

PubMed

Logue, Jennifer; Murray, Heather M; Welsh, Paul; Shepherd, James; Packard, Chris; Macfarlane, Peter; Cobbe, Stuart; Ford, Ian; Sattar, Naveed

2011-04-01

The effect of body mass index (BMI) on coronary heart disease (CHD) risk is attenuated when mediators of this risk (such as diabetes, hypertension and hyperlipidaemia) are accounted for. However, there is now evidence of a differential effect of risk factors on fatal and non-fatal CHD events, with markers of inflammation more strongly associated with fatal than non-fatal events. To describe the association with BMI separately for both fatal and non-fatal CHD risk after accounting for classical risk factors and to assess any independent effects of obesity on CHD risk. In the West of Scotland Coronary Prevention Study BMI in 6082 men (mean age 55 years) with hypercholesterolaemia, but no history of diabetes or CVD, was related to the risk of fatal and non-fatal CHD events. After excluding participants with any event in the first 2 years, 1027 non-fatal and 214 fatal CHD events occurred during 14.7 years of follow-up. A minimally adjusted model (age, sex, statin treatment) and a maximally adjusted model (including known CVD risk factors and deprivation) were compared, with BMI 25-27.4 kg/m² as referent. The risk of non-fatal events was similar across all BMI categories in both models. The risk of fatal CHD events was increased in men with BMI 30.0-39.9 kg/m² in both the minimally adjusted model (HR = 1.75 (95% CI 1.12 to 2.74)) and the maximally adjusted model (HR = 1.60 (95% CI 1.02 to 2.53)). These hypothesis generating data suggest that obesity is associated with fatal, but not non-fatal, CHD after accounting for known cardiovascular risk factors and deprivation. Clinical trial registration WOSCOPS was carried out and completed before the requirement for clinical trial registration.

Non-monogamy and risk of infection with Chlamydia trachomatis and Trichomonas vaginalis among young adults and their cohabiting partners in Peru.

PubMed

Canchihuaman, Fredy A; Carcamo, Cesar P; Garcia, Patricia J; Aral, Sevgi O; Whittington, William L H; Hawes, Stephen E; Hughes, James P; Holmes, King K

2010-12-01

To determine how patterns of non-monogamy influence prevalences of sexually transmitted infections (STIs) in individuals and their cohabitating sex partners. METHODS A 2002 survey in 24 Peruvian cities enrolled men and women aged 18-29 years from random household samples. The cohabiting sex partner of each enrolee was also enrolled until approximately 100 couples per city were recruited. Men provided urine and women vaginal swabs or urine for molecular testing for Chlamydia trachomatis and Trichomonas vaginalis; both genders provided blood for serological testing. Among 2099 females and 2052 males providing specimens and behavioural data, 18.2% of males and 2.5% of females reported non-monogamy during the past year. C trachomatis was detected in 121 females (5.8%) and 80 males (4.1%) and T vaginalis in 87 females (4.2%) and 26 males (1.3%). Multivariate analyses showed that C trachomatis infection in females was significantly associated with her male partner's non-monogamy (OR 2.02, CI 1.32 to 3.08) but not significantly with her own non-monogamy; T vaginalis was associated with her own non-monogamy (OR 3.11, CI 1.25 to 7.73) and with her partner's non-monogamy (OR 2.07, CI 1.26 to 3.42). For males, both C trachomatis (OR 2.17, CI 1.29 to 3.69) and T vaginalis (OR 2.49, CI 1.06 to 5.87) were significantly associated only with his own non-monogamy. Among cohabiting couples, male non-monogamy was common and was associated with C trachomatis and T vaginalis infection in himself and in his female partner, whereas female non-monogamy was reported infrequently and was significantly associated only with her own T vaginalis infection. Patterns of non-monogamy may guide public health interventions.

An AEM-TEM study of weathering and diagenesis, Abert Lake, Oregon. (1) Weathering reactions in the volcanics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banfield, J.F.; Veblen, D.R.; Jones, B.F.

1991-10-01

Abert Lake in south-central Oregon provides a site suitable for the study of sequential weathering and diagenetic events. In this first of two papers, transmission electron microscopy was used to characterize the igneous mineralogy, subsolidus alteration assemblage, and the structural and chemical aspects of silicate weathering reactions that occur in the volcanic rocks that outcrop around the lake. Olivine and pyroxene replacement occurred topotactically, whereas feldspar and glass alteration produced randomly oriented smectite in channels and cavities. The tetrahedral, octahedral, and interlayer compositions of the weathering products, largely dioctahedral smectites, varied with primary mineral composition, rock type, and as themore » result of addition of elements released from adjacent reaction sites. The variability within and between the smectite assemblages highlights the microenvironmental diversity, fluctuating redox conditions, and variable solution chemistry associated with mineral weathering reactions in the surficial environment. Late-stage exhalative and aqueous alteration of the volcanics redistributed many components and formed a variety of alkali and alkali-earth carbonate, chloride, sulfate, and fluoride minerals in vugs and cracks. Overall, substantial Mg, Si, Na, Ca, and K are released by weathering reactions that include the almost complete destruction of the Mg-smectite that initially replaced olivine. The leaching of these elements from the volcanics provides an important source of these constituents in the lake water. The nature of subsequent diagenetic reactions resulting from the interaction between the materials transported to the lake and the solution will be described in part.« less

Application of Novel Anion-Exchange Blend Membranes (AEBMs) to Vanadium Redox Flow Batteries.

PubMed

Cho, Hyeongrae; Krieg, Henning M; Kerres, Jochen A

2018-06-19

Both cation-exchange membranes and anion-exchange membranes are used as ion conducting membranes in vanadium redox flow batteries (VRFBs). Anion-exchange membranes (AEMs) are applied in vanadium redox flow batteries due to the high blocking property of vanadium ions via the Donnan exclusion effect. In this study, novel anion-exchange blend membranes (AEBMs) were prepared, characterized, and applied in VRFBs. Bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide), poly[(1-(4,4′-diphenylether)-5-oxybenzimidazole)-benzimidazole] (PBI-OO) and sulfonated polyether sulfone polymer were combined to prepare 3-component AEBMs with 1,2,4,5-tetramethylimidazole (TMIm) for quaternization. 3-component AEBMs showed significantly enhanced chemical and mechanical properties compared with those of 2-component AEBMs, resulting in an improved performance in VRFBs. The compositions of the anion-exchange polymers in 3-component AEBMs were systematically varied to optimize the AEBMs for the redox-flow battery application. While the 3-component AEBMs showed comparable efficiencies with Nafion ® 212 membranes, they displayed improved vanadium ions cross-over as was confirmed by open circuit voltage tests and capacity fade tests conducted in VRFBs. In addition, one of the synthesized 3-component AEBM had a superior coulombic efficiency and capacity retention in a charging⁻discharging test over 300 cycles at a current density of 40 mA/cm². It can thus be concluded that 3-component AEBMs are promising candidates for long-term operation in VRFBs.

Mechanisms of mineral membrane fouling growth modulated by pulsed modes of current during electrodialysis: evidences of water splitting implications in the appearance of the amorphous phases of magnesium hydroxide and calcium carbonate.

PubMed

Cifuentes-Araya, Nicolás; Astudillo-Castro, Carolina; Bazinet, Laurent

2014-07-15

Experiments revealed the fouling nature evolutions along different electrodialysis (ED) trials, and how it disappears when current pulsation acts repetitively on the interfaces of ion-exchange membranes (IEMs). Fouling was totally controlled on the diluate side of cation-exchange membrane (CEM) by the repetitive pulsation frequency of the higher on-duty ratios applied. They created steady water splitting proton-barriers that neutralized OH(-) leakage through the membrane, decreasing the interfacial pH, and fouling of the concentrate side. The anion-exchange membrane (AEM) on the diluate side was similarly protected, but it was fouled once water splitting OH(-) generation became either intense enough or excessively weak. Interestingly, amorphous magnesium hydroxide (AMH) stemmed on the CEM-diluate side from brucite under intense water splitting OH(-) generation, and/or strong OH(-) leakage electromigration through the membrane. Water dissociation and overlimiting current regimes triggered drastic water molecule removal from crystal lattices through an accelerated cascade water splitting reaction. Also, amorphous calcium carbonate (ACC) appeared on CEM under intense water splitting reaction, and disappeared once intense OH(-) leakage was allowed by the water splitting proton-barrier dissipation. Our findings have implications for membrane fouling control, as well as for the understanding of the growth behavior of CaCO3 and Mg(OH)2 species on electromembrane interfaces. Copyright © 2014 Elsevier Inc. All rights reserved.

Optimal level of Au nanoparticles on Pd nanostructures providing remarkable electro-catalysis in direct ethanol fuel cell

NASA Astrophysics Data System (ADS)

Dutta, Abhijit; Mondal, Achintya; Broekmann, Peter; Datta, Jayati

2017-09-01

The designing and fabrication of economically viable electro-catalysts for ethanol oxidation reaction (EOR) in direct ethanol fuel cell (DEFC) has been one of the challenging issues over the decades. The present work deals with controlled synthesis of Pd coupled Au nano structure, as the non Pt group of catalysts for DEFC. The catalytic proficiency of bimetallic NPs (2-10 nm) are found to be strongly dependent on the Pd:Au ratio. The over voltage of EOR is considerably reduced by ∼260 mV with 33% of Au content in PdAu composition compared to Pd alone, demonstrating the beneficial role of Au and/or its surface oxides providing oxygen species at much lower potentials compared to Pd. The catalysts are further subjected to electrochemical analysis through voltammetry along with the temperature study on activation parameters. The quantitative determination of EOR products during the electrolysis is carried out by ion chromatographic analysis; vis-a-vis the coulombic efficiency of the product yield were derived from each of the compositions. Furthermore, a strong correlation among catalytic performances and bimetallic composition is established by screening the catalysts in an in-house fabricated direct ethanol anion exchange membrane fuel cell, DE(AEM)FC. The performance testing demonstrates outstanding increase of peak power density (∼40 mWcm-2, 93%) for the best accomplishment Au (33%) covered Pd (67%) catalyst in comparison with the monometallic Pd.

An immunohistochemical identification key for cell types in adult mouse prostatic and urethral tissue sections

PubMed Central

Turco, Anne E.; Gottschalk, Adam; Halberg, Richard B.; Guo, Jinjin; McMahon, Jill A.; McMahon, Andrew P.

2017-01-01

Though many methods can be used to identify cell types contained in complex tissues, most require cell disaggregation and destroy information about where cells reside in relation to their microenvironment. Here, we describe a polytomous key for cell type identification in intact sections of adult mouse prostate and prostatic urethra. The key is organized as a decision tree and initiates with one round of immunostaining for nerve, epithelial, fibromuscular/hematolymphoid, or vascular associated cells. Cell identities are recursively eliminated by subsequent staining events until the remaining pool of potential cell types can be distinguished by direct comparison to other cells. We validated our identification key using wild type adult mouse prostate and urethra tissue sections and it currently resolves sixteen distinct cell populations which include three nerve fiber types as well as four epithelial, five fibromuscular/hematolymphoid, one nerve-associated, and three vascular-associated cell types. We demonstrate two uses of this novel identification methodology. We first used the identification key to characterize prostate stromal cell type changes in response to constitutive phosphatidylinositide-3-kinase activation in prostate epithelium. We then used the key to map cell lineages in a new reporter mouse strain driven by Wnt10aem1(cre/ERT2)Amc. The identification key facilitates rigorous and reproducible cell identification in prostate tissue sections and can be expanded to resolve additional cell types as new antibodies and other resources become available. PMID:29145476

Investigating the Biosynthesis of Membrane-spanning Lipids Using Model Strains of Acidobacteria

NASA Astrophysics Data System (ADS)

Bradley, A. S.; Chubiz, L. M.

2016-12-01

Glycerol dialkyl glycerol tetraethers (GDGTs), deriving from the membrane-spanning lipids of microbes, are detected in a wide range of environments including marine and lacustrine waters, sediments, and in terrestrial soils. In sediments and soils, ratios of various GDGT structures form the basis of the TEX86 proxy based on isoprenoidal GDGTs derived from archaea, and the MBT/CBT proxy based on bacterial-derived branched GDGTs (brGDGTs), which is influenced by both temperature and pH. While the relationships of the proxy values to environmental variables have been empirically calibrated, much uncertainty remains in understanding genetic and physiological factors that affect the production of these lipid structures by microbes. In this study we compare two model bacterial strains - Edaphobacter aggregans WGB-1 , which has been previously demonstrated to produce brGDGTs (Damsté et al 2011) and Edaphobacter modestus JBG-1 (a non-brGDGT producer) to gain traction into understanding brGDGT production. We have sequenced each genome, facilitating comparisons that can be used to computationally generate hypotheses for genes involved in brGDGT biosynthesis. We will also report the results of initial experiments conducted to understand how the lipid profiles of each strain vary as a function of growth phase. Through a combination of genetic approaches and physiolotical experiments, we aim to bring new understanding to brGDGTs and how proxies derived from these lipids relate to environmental variables. Damsté et al. 2011 AEM 77: 4147

2D fluorescence spectroscopy for monitoring ion-exchange membrane based technologies - Reverse electrodialysis (RED).

PubMed

Pawlowski, Sylwin; Galinha, Claudia F; Crespo, João G; Velizarov, Svetlozar

2016-01-01

Reverse electrodialysis (RED) is one of the emerging, membrane-based technologies for harvesting salinity gradient energy. In RED process, fouling is an undesirable operation constraint since it leads to a decrease of the obtainable net power density due to increasing stack electric resistance and pressure drop. Therefore, early fouling detection is one of the main challenges for successful RED technology implementation. In the present study, two-dimensional (2D) fluorescence spectroscopy was used, for the first time, as a tool for fouling monitoring in RED. Fluorescence excitation-emission matrices (EEMs) of ion-exchange membrane surfaces and of natural aqueous streams were acquired during one month of a RED stack operation. Fouling evolvement on the ion-exchange membrane surfaces was successfully followed by 2D fluorescence spectroscopy and quantified using principal components analysis (PCA). Additionally, the efficiency of cleaning strategy was assessed by measuring the membrane fluorescence emission intensity before and after cleaning. The anion-exchange membrane (AEM) surface in contact with river water showed to be significantly affected due to fouling by humic compounds, which were found to cross through the membrane from the lower salinity (river water) to higher salinity (sea water) stream. The results obtained show that the combined approach of using 2D fluorescence spectroscopy and PCA has a high potential for studying fouling development and membrane cleaning efficiency in ion exchange membrane processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimal Electromagnetic (EM) Geophysical Techniques to Map the Concentration of Subsurface Ice and Adsorbed Water on Mars and the Moon

NASA Astrophysics Data System (ADS)

Stillman, D. E.; Grimm, R. E.

2013-12-01

Water ice is ubiquitous in our Solar System and is a probable target for planetary exploration. Mapping the lateral and vertical concentration of subsurface ice from or near the surface could determine the origin of lunar and martian ice and quantify a much-needed resource for human exploration. Determining subsurface ice concentration on Earth is not trivial and has been attempted previously with electrical resistivity tomography (ERT), ground penetrating radar (GPR), airborne EM (AEM), and nuclear magnetic resonance (NMR). These EM geophysical techniques do not actually detect ice, but rather the absence of unfrozen water. This causes a non-unique interpretation of frozen and dry subsurface sediments. This works well in the arctic because most locations are not dry. However, for planetary exploration, liquid water is exceedingly rare and subsurface mapping must discriminate between an ice-rich and a dry subsurface. Luckily, nature has provided a unique electrical signature of ice: its dielectric relaxation. The dielectric relaxation of ice creates a temperature and frequency dependence of the electrical properties and varies the relative dielectric permittivity from ~3.1 at radar frequencies to >100 at low frequencies. On Mars, sediments smaller than silt size can hold enough adsorbed unfrozen water to complicate the measurement. This is because the presence of absorbed water also creates frequency-dependent electrical properties. The dielectric relaxation of adsorbed water and ice can be separated as they have different shapes and frequency ranges as long as a spectrum spanning the two relaxations is measured. The volume concentration of ice and adsorbed water is a function of the strength of their relaxations. Therefore, we suggest that capacitively-coupled dielectric spectroscopy (a.k.a. spectral induced polarization or complex resistivity) can detect the concentration of both ice and adsorbed water in the subsurface. To prove this concept we have collected dielectric spectroscopy at the Cold Regions Research and Engineering Laboratory (CRREL) permafrost tunnel in Fox, AK. We were able to detect the ice relaxation in the subsurface despite the considerable amount of subsurface unfrozen water due to the presence of montmorillonite clay and much warmer temperatures than Mars or permanently shadowed regions of the Moon. While dielectric spectroscopy can be used to determine ice and adsorbed water content it does not possess the high resolution mapping capability of a GPR. Moreover, GPR cannot detect subsurface ice content in ice-sediment mixtures as evidenced in the interpretation of the Medusae Fossae Formation. Orbital radar surveys show this unit has a low attenuation and a dielectric permittivity near 4. This allows the formation to be interpreted as ice-rich or a dry high-porosity volcanic tuff unit. Therefore, combining GPR and dielectric spectroscopy will enable high-resolution structural and volatile mapping of the subsurface. Furthermore, the addition of neutron spectroscopy would add total hydrogen abundance in the top meter. This could lead to the determination of how much hydrogen resides in ice, adsorbed water, and minerals.

Effects of spaceflight and Insulin-like Growth Factor-1 on rat bone properties

NASA Astrophysics Data System (ADS)

Bateman, Ted A.; Ayers, Reed A.; Spetzler, Michael L.; Simske, Steven J.; Zimmerman, Robert J.

1997-01-01

Spaceflight induces bone degradation which is analogous to an accelerated onset of osteoporosis in humans (Tilton et al., 1980). In rats, decreased bone formation is indicative of reduced osteoblast activity (Morey and Baylink, 1978). Chiron Corporation (Emeryville, CA) is interested in using the microgravity environment of low-Earth-orbit to test its therapeutic drug, Insulin-like Growth Factor-1 (IGF-1). This pharmaceutic is known to promote osteoblast activity (Schmid et al., 1984) and therefore may encourage bone growth in rats. Chiron sponsored the Immune.3 payload on STS-73 (May 19-29, 1996) through its Center for Space Commercialization (CSC) partner BioServe Space Technologies (University of Colorado and Kansas State University) to investigate the effects of IGF-1 on mitigating the skeletal degradation that affects rats and humans during spaceflight. Twelve rats were flown for 10 days using two Animal Enclosure Modules (AEMs) provided by NASA Ames Research Center. Of the twelve, six received 1.4 mg/day of IGF-1; the other six saline. Sixteen vivarium ground controls received the same treatment on a one day delay. Rat femora and tibiae were examined for bone mineral density via DXA scan. Femora and humeri were measured for physical and compositional properties, as well as mechanically tested in three point flexure. Quantitative histomorphometric examination of tibiae, humeri, fibulae, ribs and cranial bone; and microhardness testing on tibiae and humeri are currently in progress. Flight humeri and vivarium femora were significantly larger than their counterparts; however, significant differences in mechanical properties and mineral density were not concurrent to these mass changes.

See one, do one, teach one: advanced technology in medical education.

PubMed

Vozenilek, John; Huff, J Stephen; Reznek, Martin; Gordon, James A

2004-11-01

The concept of "learning by doing" has become less acceptable, particularly when invasive procedures and high-risk care are required. Restrictions on medical educators have prompted them to seek alternative methods to teach medical knowledge and gain procedural experience. Fortunately, the last decade has seen an explosion of the number of tools available to enhance medical education: web-based education, virtual reality, and high fidelity patient simulation. This paper presents some of the consensus statements in regard to these tools agreed upon by members of the Educational Technology Section of the 2004 AEM Consensus Conference for Informatics and Technology in Emergency Department Health Care, held in Orlando, Florida. Web-based teaching: 1) Every ED should have access to medical educational materials via the Internet, computer-based training, and other effective education methods for point-of-service information, continuing medical education, and training. 2) Real-time automated tools should be integrated into Emergency Department Information Systems [EDIS] for contemporaneous education. Virtual reality [VR]: 1) Emergency physicians and emergency medicine societies should become more involved in VR development and assessment. 2) Nationally accepted protocols for the proper assessment of VR applications should be adopted and large multi-center groups should be formed to perform these studies. High-fidelity simulation: Emergency medicine residency programs should consider the use of high-fidelity patient simulators to enhance the teaching and evaluation of core competencies among trainees. Across specialties, patient simulation, virtual reality, and the Web will soon enable medical students and residents to... see one, simulate many, do one competently, and teach everyone.

Real Time Fire Reconnaissance Satellite Monitoring System Failure Model

NASA Astrophysics Data System (ADS)

Nino Prieto, Omar Ariosto; Colmenares Guillen, Luis Enrique

2013-09-01

In this paper the Real Time Fire Reconnaissance Satellite Monitoring System is presented. This architecture is a legacy of the Detection System for Real-Time Physical Variables which is undergoing a patent process in Mexico. The methodologies for this design are the Structured Analysis for Real Time (SA- RT) [8], and the software is carried out by LACATRE (Langage d'aide à la Conception d'Application multitâche Temps Réel) [9,10] Real Time formal language. The system failures model is analyzed and the proposal is based on the formal language for the design of critical systems and Risk Assessment; AltaRica. This formal architecture uses satellites as input sensors and it was adapted from the original model which is a design pattern for physical variation detection in Real Time. The original design, whose task is to monitor events such as natural disasters and health related applications, or actual sickness monitoring and prevention, as the Real Time Diabetes Monitoring System, among others. Some related work has been presented on the Mexican Space Agency (AEM) Creation and Consultation Forums (2010-2011), and throughout the International Mexican Aerospace Science and Technology Society (SOMECYTA) international congress held in San Luis Potosí, México (2012). This Architecture will allow a Real Time Fire Satellite Monitoring, which will reduce the damage and danger caused by fires which consumes the forests and tropical forests of Mexico. This new proposal, permits having a new system that impacts on disaster prevention, by combining national and international technologies and cooperation for the benefit of humankind.

Use of Airborne Electromagnetic Geophysical Survey to Map Discontinuous Permafrost in Goldstream Valley, Interior Alaska

NASA Astrophysics Data System (ADS)

Daanen, R. P.; Emond, A.; Liljedahl, A. K.; Walter Anthony, K. M.; Barnes, D. L.; Romanovsky, V. E.; Graham, G.

2016-12-01

An airborne electromagnetic (AEM) survey was conducted in Goldstream Valley, Alaska, to map the electrical resistivity of the ground by sending a magnetic field down from a transmitter flying 30m above the ground into the subsurface. The recorded electromagnetic data are a function of the resistivity structure in the ground. The RESOLVE system used in the survey records data for six frequencies, resulting in a depth of investigation from 1-3 meters and up to 150 meters, depending on resistivity of the ground. Recording six frequencies enables the use of inversion methods to find a solution for a discretized resistivity model providing resistivity as a function of depth below ground surface. Using the airborne RESOLVE system in a populated study area involved challenges related to signal noise, access, and public opinion. Noise issues were mainly the consequence of power lines, which produce varying levels and frequencies of noise. We were not permitted to fly directly over homes, cars, animals, or people because of safety concerns, which resulted in gaps in our dataset. Public outreach well in advance of the survey informed residents about the methods used, their benefits to understanding the environment, and their potential impacts on the environment. Inversion of the data provided resistivity models that were interpreted for frozen and thawed ground conditions; these interpretation were constrained by alternate data sources such as well logs, borehole data, ground-based geophysics, and temperature measurements. The resulting permafrost map will be used to interpret groundwater movement into the valley and methane release from thermokarst lakes.

Shared Decision-making in the Emergency Department: Respecting Patient Autonomy When Seconds Count.

PubMed

Hess, Erik P; Grudzen, Corita R; Thomson, Richard; Raja, Ali S; Carpenter, Christopher R

2015-07-01

Shared decision-making (SDM), a collaborative process in which patients and providers make health care decisions together, taking into account the best scientific evidence available, as well as the patient's values and preferences, is being increasingly advocated as the optimal approach to decision-making for many health care decisions. The rapidly paced and often chaotic environment of the emergency department (ED), however, is a unique clinical setting that offers many practical and contextual challenges. Despite these challenges, in a recent survey emergency physicians reported there to be more than one reasonable management option for over 50% of their patients and that they take an SDM approach in 58% of such patients. SDM has also been selected as the topic on which to develop a future research agenda at the 2016 Academic Emergency Medicine consensus conference, "Shared Decision-making in the Emergency Department: Development of a Policy-relevant Patient-centered Research Agenda" (http://www.saem.org/annual-meeting/education/2016-aem-consensus-conference). In this paper the authors describe the conceptual model of SDM as originally conceived by Charles and Gafni and highlight aspects of the model relevant to the practice of emergency medicine. In addition, through the use of vignettes from the authors' clinical practices, the applicability of SDM to contemporary EM practice is illustrated and the ethical and pragmatic implications of taking an SDM approach are explored. It is hoped that this document will be read in advance of the 2016 Academic Emergency Medicine consensus conference, to facilitate group discussions at the conference. © 2015 by the Society for Academic Emergency Medicine.

Halomonas titanicae sp. nov., a halophilic bacterium isolated from the RMS Titanic.

PubMed

Sánchez-Porro, Cristina; Kaur, Bhavleen; Mann, Henrietta; Ventosa, Antonio

2010-12-01

A Gram-negative, heterotrophic, aerobic, non-endospore-forming, peritrichously flagellated and motile bacterial strain, designated BH1(T), was isolated from samples of rusticles, which are formed in part by a consortium of micro-organisms, collected from the RMS Titanic wreck site. The strain grew optimally at 30-37°C, pH 7.0-7.5 and in the presence of 2-8 % (w/v) NaCl. We carried out a polyphasic taxonomic study in order to characterize the strain in detail. Phylogenetic analyses based on 16S rRNA gene sequence comparison indicated that strain BH1(T) clustered within the branch consisting of species of Halomonas. The most closely related type strains were Halomonas neptunia (98.6 % 16S rRNA sequence similarity), Halomonas variabilis (98.4 %), Halomonas boliviensis (98.3 %) and Halomonas sulfidaeris (97.5 %). Other closely related species were Halomonas alkaliphila (96.5 % sequence similarity), Halomonas hydrothermalis (96.3 %), Halomonas gomseomensis (96.3 %), Halomonas venusta (96.3 %) and Halomonas meridiana (96.2 %). The major fatty acids of strain BH1(T) were C(18 : 1)ω7c (36.3 %), C(16 : 0) (18.4 %) and C(19 : 0) cyclo ω8c (17.9 %). The DNA G+C content was 60.0 mol% (T(m)). Ubiquinone 9 (Q-9) was the major lipoquinone. The phenotypic features, fatty acid profile and DNA G+C content further supported the placement of strain BH1(T) in the genus Halomonas. DNA-DNA hybridization values between strain BH1(T) and H. neptunia CECT 5815(T), H. variabilis DSM 3051(T), H. boliviensis DSM 15516(T) and H. sulfidaeris CECT 5817(T) were 19, 17, 30 and 29 %, respectively, supporting the differential taxonomic status of BH1(T). On the basis of the phenotypic, chemotaxonomic and phylogenetic data, strain BH1(T) is considered to represent a novel species, for which the name Halomonas titanicae sp. nov. is proposed. The type strain is BH1(T) (=ATCC BAA-1257(T) =CECT 7585(T) =JCM 16411(T) =LMG 25388(T)).

Allocatelliglobosispora scoriae gen. nov., sp. nov., isolated from volcanic ash.

PubMed

Lee, Dong Wan; Lee, Soon Dong

2011-02-01

A novel actinomycete, designated strain Sco-B14(T), was isolated from volcanic ash collected near Darangshi Oreum (a parasitic or satellite volcano) in Jeju, Republic of Korea. The organism formed well-developed, branched substrate mycelium, on which short chains of non-motile spores were arranged singly or in clusters. Aerial mycelium was not produced. Globose bodies were observed. The reverse colour of colonies was light brown to brown. Diffusible pigments were produced on ISP medium 3 and oatmeal-nitrate agar. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain Sco-B14(T) formed a lineage within the family Micromonosporaceae and was distinct from established genera. The 16S rRNA gene sequence similarity of strain Sco-B14(T) to members of related genera of the family was 95.0-95.7 % to type strains of Catellatospora species, 94.7 % to Hamadaea tsunoensis IMSNU 22005(T), 94.7 % to Longispora albida K97-0003(T) and 94.0 % to Catelliglobosispora koreensis LM 042(T). 3-Hydroxydiaminopimelic acid was the diagnostic diamino acid in the cell-wall peptidoglycan. Whole-cell sugars were glucose, rhamnose, ribose, xylose, arabinose, galactose and mannose. The polar lipids included diphosphatidylglycerol, phosphatidylethanolamine and phosphatidylinositol. The menaquinone profile contained MK-10(H(4)) (49 %), MK-9(H(4)) (24 %), MK-10(H(6)) (18 %) and MK-9(H(6)) (9 %). The predominant fatty acids were iso-C(15 : 0) and C(17 : 0). The DNA G+C content was 70.1 mol%. The combination of chemotaxonomic and phylogenetic data clearly separated the isolate from the type strains of all genera in the family Micromonosporaceae. On the basis of the phylogenetic and chemotaxonomic data presented in this paper, strain Sco-B14(T) is considered to represent a novel species of a new genus in the family Micromonosporaceae, for which the name Allocatelliglobosispora scoriae gen. nov., sp. nov. is proposed. The type strain of Allocatelliglobosispora scoriae is Sco-B14(T) (=KCTC 19661(T) =DSM 45362(T)).

Mineralogy and geochemistry of asbestos observed in soils developed within San Severino Lucano village (Southern Italy)

NASA Astrophysics Data System (ADS)

Bloise, Andrea; Punturo, Rosalda; Ricchiuti, Claudia; Apollaro, Carmine

2017-04-01

Concerns of potential health effects from disturbed natural occurrences of asbestos (NOA) have resulted in environmental investigations worldwide, including Basilicata region (Southern Italy). Indeed, in this region, an increased number of lung disease were related to the environmental exposure to asbestos tremolite soils sources. On the basis of the effects of asbestos on biological systems, several authors ascribe the asbestos-fibres toxicity to the synergetic effect of fibre size, crystal habit, surface reactivity, ability to generate Reactive Oxygen Species (ROS), biopersistence and chemical composition. The human health risks are based on the potential fibres inhalation, when they become airborne through rocks (e.g. serpentinite) weathering or human activities producing dust. In this frame, this paper reports the results of a detailed study on soils that developed on serpentinite bedrocks cropping out within the San Severino Lucano village (Basilicata region, Italy) in order to assess the presence of NOA potentially hazardous to human health (Bloise et al., 2016a). Twelve soil samples have been collected within the village and characterized by using different analytical techniques such as X-ray Fluorescence (XRF), X-ray powder diffraction (XRPD), scanning and transmission electron microscopy combined with energy dispersive spectrometry, analytical electron microscopy (SEM/EDS and TEM/AEM) and thermal analysis (TG, DTG, DSC, DDSC). Results pointed out as the collected soil samples contain asbestos minerals, clay minerals, diopside, quartz, and Fe-Cr oxides in various amounts. High amounts of chrysotile and asbestos tremolite were found in soils, suggesting that human activities can disturb and provoke the release of inhalable asbestos in the atmosphere, triggering thus mechanisms of hazardous exposition for population. Results also showed a high content of Fe and Cr in chrysotile in some samples, while high amount of Ni was predominantly found in asbestos tremolite. These data suggest that the cytotoxicity of asbestos could also be related to these toxic heavy metal present as impurities in their structure (Bloise et al., 2016b). Since the dispersion of fibres could be associated with carcinogenic lung cancer, in our opinion in areas where NOA can be found, the institutions should publish local maps indicating areas with mineralogical concern and realization of constructions (e. g. road) must have dust control measure to avoid hazardous exposures. References Bloise A., Punturo R., Catalano M., Miriello D., and Cirrincione R. (2016a). Naturally occurring asbestos (NOA) in rock and soil and relation with human activities: the monitoring example of selected sites in Calabria (southern Italy) Ital. J. Geosci., 135 (2): 268-279. Bloise A, Barca D, Gualtieri A F, Pollastri S, Belluso E (2016b) Trace elements in hazardous mineral fibres. Environmental Pollution 216: 314-323.

Phosphate-Catalyzed Hydrogen Peroxide Formation from Agar, Gellan, and κ-Carrageenan and Recovery of Microbial Cultivability via Catalase and Pyruvate.

PubMed

Kawasaki, Kosei; Kamagata, Yoichi

2017-11-01

Previously, we reported that when agar is autoclaved with phosphate buffer, hydrogen peroxide (H 2 O 2 ) is formed in the resulting medium (PT medium), and the colony count on the medium inoculated with environmental samples becomes much lower than that on a medium in which agar and phosphate are autoclaved separately (PS medium) (T. Tanaka et al., Appl Environ Microbiol 80:7659-7666, 2014, https://doi.org/10.1128/AEM.02741-14). However, the physicochemical mechanisms underlying this observation remain largely unknown. Here, we determined the factors affecting H 2 O 2 formation in agar. The H 2 O 2 formation was pH dependent: H 2 O 2 was formed at high concentrations in an alkaline or neutral phosphate buffer but not in an acidic buffer. Ammonium ions enhanced H 2 O 2 formation, implying the involvement of the Maillard reaction catalyzed by phosphate. We found that other gelling agents (e.g., gellan and κ-carrageenan) also produced H 2 O 2 after being autoclaved with phosphate. We then examined the cultivability of microorganisms from a fresh-water sample to test whether catalase and pyruvate, known as H 2 O 2 scavengers, are effective in yielding high colony counts. The colony count on PT medium was only 5.7% of that on PS medium. Catalase treatment effectively restored the colony count of PT medium (to 106% of that on PS medium). In contrast, pyruvate was not as effective as catalase: the colony count on sodium pyruvate-supplemented PT medium was 58% of that on PS medium. Given that both catalase and pyruvate can remove H 2 O 2 from PT medium, these observations indicate that although H 2 O 2 is the main cause of reduced colony count on PT medium, other unknown growth-inhibiting substances that cannot be removed by pyruvate (but can be by catalase) may also be involved. IMPORTANCE The majority of bacteria in natural environments are recalcitrant to laboratory culture techniques. Previously, we demonstrated that one reason for this is the formation of high H 2 O 2 levels in media prepared by autoclaving agar and phosphate buffer together (PT medium). In this study, we investigated the factors affecting H 2 O 2 formation from agar. H 2 O 2 formation is pH dependent, and ammonium ions promote this phosphate-catalyzed H 2 O 2 formation. Amendment of catalase or pyruvate, a well-known H 2 O 2 -scavenging agent, effectively eliminated H 2 O 2 Yet results suggest that growth-inhibiting factor(s) that cannot be eliminated by pyruvate (but can be by catalase) are present in PT medium. Copyright © 2017 American Society for Microbiology.

Phosphate-Catalyzed Hydrogen Peroxide Formation from Agar, Gellan, and κ-Carrageenan and Recovery of Microbial Cultivability via Catalase and Pyruvate

PubMed Central

Kamagata, Yoichi

2017-01-01

ABSTRACT Previously, we reported that when agar is autoclaved with phosphate buffer, hydrogen peroxide (H2O2) is formed in the resulting medium (PT medium), and the colony count on the medium inoculated with environmental samples becomes much lower than that on a medium in which agar and phosphate are autoclaved separately (PS medium) (T. Tanaka et al., Appl Environ Microbiol 80:7659–7666, 2014, https://doi.org/10.1128/AEM.02741-14). However, the physicochemical mechanisms underlying this observation remain largely unknown. Here, we determined the factors affecting H2O2 formation in agar. The H2O2 formation was pH dependent: H2O2 was formed at high concentrations in an alkaline or neutral phosphate buffer but not in an acidic buffer. Ammonium ions enhanced H2O2 formation, implying the involvement of the Maillard reaction catalyzed by phosphate. We found that other gelling agents (e.g., gellan and κ-carrageenan) also produced H2O2 after being autoclaved with phosphate. We then examined the cultivability of microorganisms from a fresh-water sample to test whether catalase and pyruvate, known as H2O2 scavengers, are effective in yielding high colony counts. The colony count on PT medium was only 5.7% of that on PS medium. Catalase treatment effectively restored the colony count of PT medium (to 106% of that on PS medium). In contrast, pyruvate was not as effective as catalase: the colony count on sodium pyruvate-supplemented PT medium was 58% of that on PS medium. Given that both catalase and pyruvate can remove H2O2 from PT medium, these observations indicate that although H2O2 is the main cause of reduced colony count on PT medium, other unknown growth-inhibiting substances that cannot be removed by pyruvate (but can be by catalase) may also be involved. IMPORTANCE The majority of bacteria in natural environments are recalcitrant to laboratory culture techniques. Previously, we demonstrated that one reason for this is the formation of high H2O2 levels in media prepared by autoclaving agar and phosphate buffer together (PT medium). In this study, we investigated the factors affecting H2O2 formation from agar. H2O2 formation is pH dependent, and ammonium ions promote this phosphate-catalyzed H2O2 formation. Amendment of catalase or pyruvate, a well-known H2O2-scavenging agent, effectively eliminated H2O2. Yet results suggest that growth-inhibiting factor(s) that cannot be eliminated by pyruvate (but can be by catalase) are present in PT medium. PMID:28821549

Environmental services coupled to food products and brands: food companies interests and on-farm accounting.

PubMed

Kempa, Daniela

2013-09-01

Much research has been carried out on governmental support of agri environmental measures (AEM). However, little is known about demands on and incentives from the commercial market for environmental contributions of the farmers. The factors farm structures, level of remuneration and legal framework have been thoroughly investigated. However, demands of the food industry for environmentally friendly goods(1) and their effects on farmers' decisions have not yet been analyzed. Leading companies in the food industry have observed an increasing consumer awareness and, due to higher competition, see an additional need to communicate environmental benefits which result from either organic production methods or agri-environmental measures. To address this research deficit, two case studies were carried out. The first case study is a survey aimed at the industrial food producers' demands with regards to the environmental performance of supplying farms. Concurrently, within a second survey farmers were questioned to find out what conditions are required to implement agri-environmental measures beyond cross compliance and document their environmental performance. This article presents the outcomes of the first case study. The results show that food companies have an interest in the documentation of environmental benefits of supplying farms for their marketing strategies. Provision of support by finance or contract-design is also seen as appropriate tool to promote an environmentally friendly production. In turn the food producers' demand and support for documented environmental services can have a positive influence on farmers' decisions for implementation and documentation of these services. Thus, the surveys provide essential findings for further development of documentation strategies for environmental benefits within the supply chain. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of spaceflight and Insulin-like Growth Factor-1 on rat bone properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bateman, T.A.; Ayers, R.A.; Spetzler, M.L.

Spaceflight induces bone degradation which is analogous to an accelerated onset of osteoporosis in humans (Tilton {ital et al.}, 1980). In rats, decreased bone formation is indicative of reduced osteoblast activity (Morey and Baylink, 1978). Chiron Corporation (Emeryville, CA) is interested in using the microgravity environment of low-Earth-orbit to test its therapeutic drug, Insulin-like Growth Factor-1 (IGF-1). This pharmaceutic is known to promote osteoblast activity (Schmid {ital et al.}, 1984) and therefore may encourage bone growth in rats. Chiron sponsored the Immune.3 payload on STS-73 (May 19{endash}29, 1996) through its Center for Space Commercialization (CSC) partner BioServe Space Technologies (Universitymore » of Colorado and Kansas State University) to investigate the effects of IGF-1 on mitigating the skeletal degradation that affects rats and humans during spaceflight. Twelve rats were flown for 10 days using two Animal Enclosure Modules (AEMs) provided by NASA Ames Research Center. Of the twelve, six received 1.4 mg/day of IGF-1; the other six saline. Sixteen vivarium ground controls received the same treatment on a one day delay. Rat femora and tibiae were examined for bone mineral density via DXA scan. Femora and humeri were measured for physical and compositional properties, as well as mechanically tested in three point flexure. Quantitative histomorphometric examination of tibiae, humeri, fibulae, ribs and cranial bone; and microhardness testing on tibiae and humeri are currently in progress. Flight humeri and vivarium femora were significantly larger than their counterparts; however, significant differences in mechanical properties and mineral density were not concurrent to these mass changes. {copyright} {ital 1997 American Institute of Physics.}« less

Histidine at Position 195 is Essential for Association of Heme-b in Lcp1VH2

NASA Astrophysics Data System (ADS)

Oetermann, Sylvia; Vivod, Robin; Hiessl, Sebastian; Hogeback, Jens; Holtkamp, Michael; Karst, Uwe; Steinbüchel, Alexander

2018-03-01

The latex clearing protein (Lcp) is the key enzyme of polyisoprene degradation in actinomycetes (Yikmis and Steinbüchel in Appl Environ Microbiol 78:4543-4551, https://doi.org/10.1128/AEM.00001-12, 2012). In this study it was shown that Lcp from Gordonia polyisoprenivorans VH2 (Lcp1VH2) harbors a non-covalently bound heme b as cofactor, which was identified by pyridine hemochrome spectra and confirmed by LC/ESI-ToF-MS. It contains iron, most likely in the Fe3+ state. We focused on the characterization of the heme-cofactor, its accessibility with respect to the conformation of Lcp1VH2, and the identification of putative histidine residues involved in the coordination of heme. A change was detectable in UV/Vis-spectra of reduced Lcp1VH2 when imidazole was added, showing that Lcp1VH2 "as isolated" occurs in an open state, directly being accessible for external ligands. In addition, three highly conserved histidines (H195, H200 and H228), presumably acting as ligands coordinating the heme within the heme pocket, were replaced with alanines by site-directed mutagenesis. The effect of these changes on in vivo rubber-mineralization was investigated. The lcp- deletion mutant complemented with the H195A variant of lcp1 VH2 was unable to mineralize poly(cis-1,4-isoprene). In vitro analyses of purified, recombinant Lcp1VH2H195A confirmed the loss of enzyme activity, which could be ascribed to the loss of heme. Hence, H195 is essential for the association of heme-b in the central region of Lcp1VH2.

Germination of Aspergillus niger conidia is triggered by nitrogen compounds related to L-amino acids.

PubMed

Hayer, Kimran; Stratford, Malcolm; Archer, David B

2014-10-01

Conidial germination is fundamentally important to the growth and dissemination of most fungi. It has been previously shown (K. Hayer, M. Stratford, and D. B. Archer, Appl. Environ. Microbiol. 79:6924-6931, 2013, http://dx.doi.org/10.1128/AEM.02061-13), using sugar analogs, that germination is a 2-stage process involving triggering of germination and then nutrient uptake for hyphal outgrowth. In the present study, we tested this 2-stage germination process using a series of nitrogen-containing compounds for the ability to trigger the breaking of dormancy of Aspergillus niger conidia and then to support the formation of hyphae by acting as nitrogen sources. Triggering and germination were also compared between A. niger and Aspergillus nidulans using 2-deoxy-D-glucose (trigger), D-galactose (nontrigger in A. niger but trigger in A. nidulans), and an N source (required in A. niger but not in A. nidulans). Although most of the nitrogen compounds studied served as nitrogen sources for growth, only some nitrogen compounds could trigger germination of A. niger conidia, and all were related to L-amino acids. Using L-amino acid analogs without either the amine or the carboxylic acid group revealed that both the amine and carboxylic acid groups were essential for an L-amino acid to serve as a trigger molecule. Generally, conidia were able to sense and recognize nitrogen compounds that fitted into a specific size range. There was no evidence of uptake of either triggering or nontriggering compounds over the first 90 min of A. niger conidial germination, suggesting that the germination trigger sensors are not located within the spore. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

Dual-Color Bioluminescence Imaging for Simultaneous Monitoring of the Intestinal Persistence of Lactobacillus plantarum and Lactococcus lactis in Living Mice

PubMed Central

Poiret, Sabine; Dennin, Véronique; Boutillier, Denise; Lacorre, Delphine Armelle; Foligné, Benoit; Pot, Bruno

2015-01-01

Lactic acid bacteria are found in the gastrointestinal tract of mammals and have received tremendous attention due to their health-promoting properties. We report the development of two dual-color luciferase-producing Lactobacillus (Lb.) plantarum and Lactococcus (Lc.) lactis strains for noninvasive simultaneous tracking in the mouse gastrointestinal tract. We previously described the functional expression of the red luciferase mutant (CBRluc) from Pyrophorus plagiophthalamus in Lb. plantarum NCIMB8826 and Lc. lactis MG1363 (C. Daniel, S. Poiret, V. Dennin, D. Boutillier, and B. Pot, Appl Environ Microbiol 79:1086–1094, 2013, http://dx.doi.org/10.1128/AEM.03221-12). In this study, we determined that CBRluc is a better-performing luciferase for in vivo localization of both lactic acid bacteria after oral administration than the green click beetle luciferase mutant construct developed in this study. We further established the possibility to simultaneously detect red- and green-emitting lactic acid bacteria by dual-wavelength bioluminescence imaging in combination with spectral unmixing. The difference in spectra of light emission by the red and green click beetle luciferase mutants and dual bioluminescence detection allowed in vitro and in vivo quantification of the red and green emitted signals; thus, it allowed us to monitor the dynamics and fate of the two bacterial populations simultaneously. Persistence and viability of both strains simultaneously administered to mice in different ratios was studied in vivo in anesthetized mice and ex vivo in mouse feces. The application of dual-luciferase-labeled bacteria has considerable potential to simultaneously study the interactions and potential competitions of different targeted bacteria and their hosts. PMID:26025906

UXO Engineering Design. Technical Specification and ConceptualDesign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beche, J-F.; Doolittle, L.; Greer, J.

2005-04-23

The design and fabrication of the UXO detector has numerous challenges and is an important component to the success of this study. This section describes the overall engineering approach, as well as some of the technical details that brought us to the present design. In general, an array of sensor coils is measuring the signal generated by the UXO object in response to a stimulation provided by the driver coil. The information related to the location, shape and properties of the object is derived from the analysis of the measured data. Each sensor coil is instrumented with a waveform digitizermore » operating at a nominal digitization rate of 100 kSamples per second. The sensor coils record both the large transient pulse of the driver coil and the UXO object response pulse. The latter is smaller in amplitude and must be extracted from the large transient signal. The resolution required is 16 bits over a dynamic range of at least 140 dB. The useful signal bandwidth of the application extends from DC to 40 kHz. The low distortion of each component is crucial in order to maintain an excellent linearity over the full dynamic range and to minimize the calibration procedure. The electronics must be made as compact as possible so that the response of its metallic parts has a minimum signature response. Also because of a field system portability requirement, the power consumption of the instrument must be kept as low as possible. The theory and results of numerical and experimental studies that led to the proof-of-principle multitransmitter-multireceiver Active ElectroMagnetic (AEM) system, that can not only accurately detect but also characterize and discriminate UXO targets, are summarized in LBNL report-53962: ''Detection and Classification of Buried Metallic Objects, UX-1225''.« less

Occurrence of wide-chain Ca-pyriboles as primary crystals in the Salton Sea Geothermal Field, California, USA

NASA Astrophysics Data System (ADS)

Yau, Yu-Chyi; Peacor, Donald R.; Essene, Eric J.

1986-09-01

Amphiboles and pyroxenes occurring in the Salton Sea Geothermal Field were found to contain coherent intergrowths of chain silicates with other than double and single chain widths by using transmission and analytical electron microscopy. Both occur in the biotite zone at the temperature (depth) interval of 310° C (1,060 m) to 330° C (1,547m) which approximately corresponds to temperatures of the greenschist facies. The amphiboles occur as euhedral fibrous crystals occupying void space and are composed primarily of irregularly alternating (010) slabs of double or triple chains, with rare quadruple and quintuple chains. Primary crystallization from solution results in euhedral crystals. Clinopyroxenes formed mainly as a porefilling cement and subordinately as prismatic crystals coexisting with fibrous amphiboles. Fine lamellae of double and triple chains are irregularly intercalated with pyroxene. AEM analyses yield formulae (Ca1.8Mg2.9Fe1.9Mn0.1) Si8O21.8(OH)1.8 (310° C) and (Ca2.0Fe2.5Mg2.3) Si8O21.8 (OH)2.0 (330° C) for amphiboles and (Ca1.1Fe0.6Mg0.3) Si2O6 for clinopyroxene. Thermodynamic calculations at Pfluid=100 bar of equilibrium reactions of (1) 3 chlorite +10 calcite + 21 quartz = 3 actinolite + 2 clinozoisite + 8 H2O + 10 CO2 and (2) actinolite+ 3 calcite+ 2 quartz = 5 clinopyroxene + H2O + 3 CO2 using Mg-end member phases indicate that formation of amphibole and pyroxene require very water-rich conditions (X_{CO_2 } < 0.06) at temperatures below 330° C.

FRESHEM - Fresh-saline groundwater distribution in Zeeland (NL) derived from airborne EM

NASA Astrophysics Data System (ADS)

Siemon, Bernhard; van Baaren, Esther; Dabekaussen, Willem; Delsman, Joost; Gunnik, Jan; Karaoulis, Marios; de Louw, Perry; Oude Essink, Gualbert; Pauw, Pieter; Steuer, Annika; Meyer, Uwe

2017-04-01

In a setting of predominantly saline surface waters, the availability of fresh water for agricultural purposes is not obvious in Zeeland, The Netherlands. Canals and ditches are mainly brackish to saline due to saline seepage, which originates from old marine deposits and salt-water transgressions during historical times. The only available fresh groundwater is present in the form of freshwater lenses floating on top of the saline groundwater. This fresh groundwater is vital for agricultural, industrial, ecological, water conservation and drinking water functions. An essential first step for managing this fresh groundwater properly is to know the present spatial fresh-brackish-saline groundwater distribution. As traditional salinity monitoring is labour-intensive, airborne electromagnetics (AEM), which is fast and can cover large areas in short time, is an efficient alternative. A consortium of BGR, Deltares and TNO started FRESHEM Zeeland (FREsh Salt groundwater distribution by Helicopter ElectroMagnetic survey in the Province of Zeeland) in October 2014. Within 3x2 weeks of the first project year, the entire area of about 2000 km2 was surveyed using BGR's helicopter-borne geophysical system totalling to about 10,000 line-km. The HEM datasets of 17 subareas were carefully processed using advanced BGR in-house software and inverted to 2.5 Million resistivity-depth models. Ground truthing demonstrated that the large-scale HEM results fit very well with small-scale ground EM data (ECPT). Based on this spatial resistivity distribution, a 3D voxel model for Chloride concentration was derived for the entire province taking into account geological model data (GeoTOP) for the lithology correction and local in-situ groundwater measurements for the translation of water conductivity to Chloride concentration. The 3D voxel model enables stakeholders to implement spatial Chloride concentration in their groundwater models.

An Fe-S cluster in the conserved Cys-rich region in the catalytic subunit of FAD-dependent dehydrogenase complexes.

PubMed

Shiota, Masaki; Yamazaki, Tomohiko; Yoshimatsu, Keiichi; Kojima, Katsuhiro; Tsugawa, Wakako; Ferri, Stefano; Sode, Koji

2016-12-01

Several bacterial flavin adenine dinucleotide (FAD)-harboring dehydrogenase complexes comprise three distinct subunits: a catalytic subunit with FAD, a cytochrome c subunit containing three hemes, and a small subunit. Owing to the cytochrome c subunit, these dehydrogenase complexes have the potential to transfer electrons directly to an electrode. Despite various electrochemical applications and engineering studies of FAD-dependent dehydrogenase complexes, the intra/inter-molecular electron transfer pathway has not yet been revealed. In this study, we focused on the conserved Cys-rich region in the catalytic subunits using the catalytic subunit of FAD dependent glucose dehydrogenase complex (FADGDH) as a model, and site-directed mutagenesis and electron paramagnetic resonance (EPR) were performed. By co-expressing a hitch-hiker protein (γ-subunit) and a catalytic subunit (α-subunit), FADGDH γα complexes were prepared, and the properties of the catalytic subunit of both wild type and mutant FADGDHs were investigated. Substitution of the conserved Cys residues with Ser resulted in the loss of dye-mediated glucose dehydrogenase activity. ICP-AEM and EPR analyses of the wild-type FADGDH catalytic subunit revealed the presence of a 3Fe-4S-type iron-sulfur cluster, whereas none of the Ser-substituted mutants showed the EPR spectrum characteristic for this cluster. The results suggested that three Cys residues in the Cys-rich region constitute an iron-sulfur cluster that may play an important role in the electron transfer from FAD (intra-molecular) to the multi-heme cytochrome c subunit (inter-molecular) electron transfer pathway. These features appear to be conserved in the other three-subunit dehydrogenases having an FAD cofactor. Copyright © 2016 Elsevier B.V. All rights reserved.

A Quasi Experiment to Determine the Effectiveness of a "Partially Flipped" versus "Fully Flipped" Undergraduate Class in Genetics and Evolution.

PubMed

Adams, Alison E M; Garcia, Jocelyn; Traustadóttir, Tinna

2016-01-01

Two sections of Genetics and Evolution were taught by one instructor. One group (the fully flipped section) had the entire class period devoted to active learning (with background material that had to be watched before class), and the other group (the partially flipped section) had just a portion of class time spent on active learning (with the background material presented during class time). The same materials and assessments were used for both sections. Analysis of objective measures revealed that there was no significant difference between the learning outcomes of students in the two sections. There was no main effect of gender, major, or ethnicity on success in the whole cohort or in either section. There appeared to be a significant main effect of class standing, with freshmen performing significantly less well than sophomores, juniors, or seniors (who all performed equally well) in both sections (p < 0.01); however, this was a very preliminary observation, as there were very few freshmen in either section. The only predictor of success in the two sections was prior grade point average. An anonymous end-of-semester survey showed no significant difference between the two sections in interest in the subject matter. © 2016 A.E.M. Adams et al. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

HRTEM/AEM and SEM study of fluid-rock interactions: Interaction of copper, silver, selenium, chromium, and cadmium-bearing solutions with geological materials at near surface conditions, with an emphasis on phyllosilicates. Progress report, September 1, 1992--September 1, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veblen, D.R.; Ilton, E.S.

1993-05-01

TEM of naturally occurring Cu-rich biotites and feldspars from weathered portions of porphyry copper deposits has shown that copper is not in the structure of these minerals, is present in their weathering products such as copper-rich vermiculite layers, submicroscopic iron oxyhydroxides and native copper inclusions, and chrysocoua. Reaction of acidic solutions bearing-Cu{sup 2+}, Ag{sup +}, Cr{sup 6+}, and Se{sup 4+}, at 25C, with biotite indicates that ferrous iron in biotite can reduce Cu{sup 2+}, Ag+, and Cr{sup 6+} to Cu{degrees}, Ag{degrees}, and Cr(III), respectively. However, Se{sup 4+} does not appear to be reduced. Copper is reduced in the interlayer region,more » silver is reduced in the interlayer and on the biotite surfaces, and chromium is reduced at the biotite surface. TEM shows that the reduction of copper and silver by biotite can produce native metal inclusions, whereas reduction of Cr(VI) to CR(III) did not produce any Cr-bearing precipitates. The copper and silver experiments show that iron in biotite can be a much stronger reducing agent than iron in solution. TEM and XPS of biotites reacted with CR(VI) clearly show that edges or (hkO) faces are much more reactive than the basal planes, where the edges are strongly enriched in CR(III) relative to the basal planes. In contrast, biotites reacted with Cr(IH)-bearing solutions show little fractionation between the edges and basal planes. Another important result of our XPS studies is that we demonstrated that the oxidation state of near surface iron in biotite can be quantified.« less

Associations between maternal experiences of intimate partner violence and child nutrition and mortality: findings from Demographic and Health Surveys in Egypt, Honduras, Kenya, Malawi and Rwanda.

PubMed

Rico, Emily; Fenn, Bridget; Abramsky, Tanya; Watts, Charlotte

2011-04-01

If effective interventions are to be used to address child mortality and malnutrition, then it is important that we understand the different pathways operating within the framework of child health. More attention needs to be given to understanding the contribution of social influences such as intimate partner violence (IPV). To investigate the relationship between maternal exposure to IPV and child mortality and malnutrition using data from five developing countries. Population data from Egypt, Honduras, Kenya, Malawi and Rwanda were analysed. Logistic regression analysis was used to generate odds ratios of the associations between several categories of maternal exposure to IPV since the age of 15 and three child outcomes: under-2-year-old (U2) mortality and moderate and severe stunting (<-2 Z-score height-for-age and <-3 Z-score height-for-age) in 6-59-month-old children. Analyses were adjusted for potential confounders, and the role of mediating factors was explored. The prevalence of physical and/or sexual IPV since the age of 15 years ranged from 15.5% (Honduras) to 46.2% (Kenya). For child stunting, prevalence ranged from 25.4% (Egypt) to 58.0% (Malawi) and for U2 mortality from 3.6% (Honduras) to 15.2% (Rwanda). In Kenya, maternal exposure to IPV was associated with higher U2 mortality (adjusted odds ratio (OR)=1.42, 95% CI 1.18 to 1.71) and child stunting (adjusted OR=1.36, 95% CI 1.16 to 1.61). In Malawi and Honduras, marginal associations were observed between IPV and severe stunting and U2 mortality, respectively, with strength of associations varying by type of violence. The relationship between IPV and U2 mortality and stunting in Kenya, Honduras and Malawi suggests that, in these countries, IPV plays a role in child malnutrition and mortality. This contributes to a growing body of evidence that broader public health benefits may be incurred if efforts to address IPV are incorporated into a wider range of maternal and child health programmes; however, the authors highlight the need for more research that can establish temporality, use data collected on the basis of the study's objectives, and further explore the causal framework of this relationship using more advanced statistical analysis.

An interpretation of the 1997 airborne electromagnetic (AEM) survey, Fort Huachuca vicinity, Cochise County, Arizona

USGS Publications Warehouse

Bultman, M.W.; Gettings, M.E.; Wynn, Jeff

1999-01-01

Executive Summary -- In March of 1997, an airborne electromagnetic (AEM) survey of the Fort Huachuca Military Reservation and immediate surrounds (location map, http://geopubs.wr.usgs.gov/open-file/of99-007-b/index.jpg) was conducted. This survey was sponsored by the U.S. Army and contracted through the Geologic Division of the U.S. Geological Survey (USGS). Data were gathered by Geoterrex-Dighem Ltd. of Ottawa, Canada. The survey aircraft is surrounded by a coil through which a large current pulse is passed. This pulse induces currents in the Earth which are recorded by a set of three mutually perpendicular coils towed in a 'bird' about 100 m behind and below the aircraft. The bird also records the Earth's magnetic field. The system samples the Earth response to the electromagnetic pulse about every 16 m along the aircraft flight path. For this survey, the bulk of the flightpaths were spaced about 400 m apart and oriented in a northeast-southwest direction extending from bedrock over the Huachuca Mountains to bedrock over the Tombstone Hills. A preliminary report on the unprocessed data collected in the field was delivered to the U.S. Army by USGS in July 1997 (USGS Open-File Report 97?457). The final data were delivered in March, 1998 by the contractor to USGS and thence to the U.S. Army. The present report represents the final interpretive report from USGS. The objectives of the survey were to: 1) define the structure of the San Pedro basin in the Sierra Vista-Fort Huachuca-Huachuca City area, including the depth and shape of the basin, and to delineate large faults that may be active within the basin fill and therefore important in the hydrologic regime; 2) define near surface and subsurface areas that contain a large volume fraction of silt and clay in the basin fill and which both reduce the volume of available storage for water and reduce the permeability of the aquifer; and 3) to evaluate the use of the time domain electromagnetic method in the southwest desert setting as a means of mapping depth to water. Chapter one, written by M.E. Gettings, reports the results of the analysis of the aeromagnetic anomaly data. Depths to magnetic rocks computed from these data are in good agreement with depths from gravity anomaly models (Gettings and Houser, in prep.) and confirm and refine the location of the bedrock highs which reach to within 200 m of the surface in several parts of the study area. The highly faulted and generally shallow character of the basin within the study area deduced from the gravity studies is also evident in the aeromagnetic data. The caldera ring fault delimiting the buried structural southwest edge of the Tombstone caldera is expressed in the magnetic data and deeper intrusives extending outside the caldera to the southwest are inferred. Several magnetic bodies occur at shallow depths within the Precambrian granite of the Huachuca Mountains along the eastern foothills of the mountains. These are inferred to be Tertiary intrusives but remain to be confirmed by field work if any of their uppermost dikes or apotheses are exposed. Faults delineating the east-west trending bedrock high beneath the city of Sierra Vista appear to be shallow and should be investigated for surface expressions. Chapter two, written by Jeff Wynn, analyzes and interprets the conductivity depth transforms (CDTs) and provides a general evaluation of the data quality. He concludes that there is a good general correlation between the uppermost conductor seen in the CDTs and water table depth in many cases. Detailed comparisons between the ground-based vertical electric soundings (VES) and the CDTs are reported in this chapter. The two sets of data compare well in general for most sounding sites where the VES data are not noisy. In general the airborne data appear to have (a) less noise and (b) greater depth penetration in comparison to the VES results, but the resistivity transformations in the CDTs are reliable only for the

Naturally weathered feldspar surfaces in the Navajo Sandstone aquifer, Black Mesa, Arizona: Electron microscopic characterization

NASA Astrophysics Data System (ADS)

Zhu, Chen; Veblen, David R.; Blum, Alex E.; Chipera, Stephen J.

2006-09-01

Naturally weathered feldspar surfaces in the Jurassic Navajo Sandstone at Black Mesa, Arizona, was characterized with high-resolution transmission and analytical electron microscope (HRTEM-AEM) and field emission gun scanning electron microscope (FEG-SEM). Here, we report the first HRTEM observation of a 10-nm thick amorphous layer on naturally weathered K-feldspar in currently slightly alkaline groundwater. The amorphous layer is probably deficient in K and enriched in Si. In addition to the amorphous layer, the feldspar surfaces are also partially coated with tightly adhered kaolin platelets. Outside of the kaolin coatings, feldspar grains are covered with a continuous 3-5 μm thick layer of authigenic smectite, which also coats quartz and other sediment grains. Authigenic K-feldspar overgrowth and etch pits were also found on feldspar grains. These characteristics of the aged feldspar surfaces accentuate the differences in reactivity between the freshly ground feldspar powders used in laboratory experiments and feldspar grains in natural systems, and may partially contribute to the commonly observed apparent laboratory-field dissolution rate discrepancy. At Black Mesa, feldspars in the Navajo Sandstone are dissolving at ˜10 5 times slower than laboratory rate at comparable temperature and pH under far from equilibrium condition. The tightly adhered kaolin platelets reduce the feldspar reactive surface area, and the authigenic K-feldspar overgrowth reduces the feldspar reactivity. However, the continuous smectite coating layer does not appear to constitute a diffusion barrier. The exact role of the amorphous layer on feldspar dissolution kinetics depends on the origin of the layer (leached layer versus re-precipitated silica), which is uncertain at present. However, the nanometer thin layer can be detected only with HRTEM, and thus our study raises the possibility of its wide occurrence in geological systems. Rate laws and proposed mechanisms should consider the possibility of this amorphous layer on feldspar surface.

Evaluation of Timepix silicon detector for the detection of 18F positrons

NASA Astrophysics Data System (ADS)

Wang, Q.; Tous, J.; Liu, Z.; Ziegler, S.; Shi, K.

2014-05-01

Timepix is an evolving energy and position sensitive pixel detector. It consists of a silicon detector (sensitive layer 300 μm thick) bump-bonded to the Timepix readout chip developed by the Medipix2 collaboration. This study aims to test the feasibility of using the acquired energy and position signals from Timepix for positron imaging. The signals of the commonly used fluorine-18 PET (positron emission tomography) tracer [18F]FDG were measured using Timepix operated both in single particle counting (Medipix) and in time over threshold (TOT) modes. The spatial resolution (SR) was measured using the absorber edge method (AEM) and was calculated from the over-sampled line spread function. The track of a positron in the Timepix detector was characterized as a cluster and the energy weighted centroid of each cluster was considered as readout for the position of the positron incidence. The measurement results were compared with theoretical predictions using Monte-Carlo simulations. In addition, imaging of a tissue slice of a mouse heart was analysed with reference to standard phosphor plate imaging. Our results show that the SR was improved from 177.1±4.1 μm (centroid without energy weighting) to 155.5±3.1 μm μm (centroid with energy weighting). About 12% enhancement of SR was achieved with energy information in TOT mode. The sensitivity of Timepix was 0.35 cps/Bq based on the measurements. The measuring background and the ratio between detected positrons and gamma rays were also evaluated and were found to be consistent with theoretical predictions. A small enhancement of image quality was also achieved by applying energy information to the data of the measured tissue sample. Our results show that the inclusion of energy information could slightly enhance the positron measurement compared to without energy information and the Timepix provides a high SR and sensitivity for positron detection. Thus, Timepix is a potentially effective tool for 2D positron imaging.

Interseismic Deformation along the Red River Fault from InSAR Measurements

NASA Astrophysics Data System (ADS)

Chen, J.; Li, Z.; Clarke, P. J.

2017-12-01

The Red River Fault (RRF) zone is a profound geological discontinuity separating South China from Indochina. Right lateral movements along this >900 km fault are considered to accommodate the extrusion of SE China. Crustal deformation monitoring at high resolution is the key to understand the present-day mode of deformation in this zone and its interaction with the adjacent regions. This is the first study to measure the interseismic deformation of the entire fault with ALOS-1/2 and Sentinel-1 observations. Nine ascending tracks of ALOS-1 data between 2007 and 2011 are collected from the Alaska Satellite Facility (ASF), four descending tracks of Sentinel-1 data are acquired every 24 days since October 2014, and ALOS-2 data are being systematically acquired since 2014. The long wavelength (L-band) of ALOS-1/2 and short temporal baseline of Sentinel-1 ensure good coherence to overcome the limitations of heavy vegetation and variable climate in the region. Stacks of interferograms are generated by our automatic processing chain based on the InSAR Scientific Computing Environment (ISCE) software, ionospheric errors are estimated and corrected using the split-spectrum method (Fattahi et al., IEEE Trans. Geosci. Remote Sens., 2017) and the tropospheric delays are calibrated using the Generic Atmospheric Correction Online Service for InSAR (GACOS: http://ceg-research.ncl.ac.uk/v2/gacos) with high-resolution ECMWF products (Yu et al., J. Geophys. Res., 2017). Time series analysis is performed to determine the interseismic deformation rate of the RRF using the in-house InSAR time series with atmospheric estimation model (InSAR TS + AEM) package based on the Small Baseline Subset (SBAS) algorithm. Our results reveal the decrease of slip rate from north to south. We map the interseismic strain rate field to characterize the deformation patterns and seismic hazard throughout the RRF zone.

A model for emergency department end-of-life communications after acute devastating events--part I: decision-making capacity, surrogates, and advance directives.

PubMed

Limehouse, Walter E; Feeser, V Ramana; Bookman, Kelly J; Derse, Arthur

2012-09-01

Making decisions for a patient affected by sudden devastating illness or injury traumatizes a patient's family and loved ones. Even in the absence of an emergency, surrogates making end-of-life treatment decisions may experience negative emotional effects. Helping surrogates with these end-of-life decisions under emergent conditions requires the emergency physician (EP) to be clear, making medical recommendations with sensitivity. This model for emergency department (ED) end-of-life communications after acute devastating events comprises the following steps: 1) determine the patient's decision-making capacity; 2) identify the legal surrogate; 3) elicit patient values as expressed in completed advance directives; 4) determine patient/surrogate understanding of the life-limiting event and expectant treatment goals; 5) convey physician understanding of the event, including prognosis, treatment options, and recommendation; 6) share decisions regarding withdrawing or withholding of resuscitative efforts, using available resources and considering options for organ donation; and 7) revise treatment goals as needed. Emergency physicians should break bad news compassionately, yet sufficiently, so that surrogate and family understand both the gravity of the situation and the lack of long-term benefit of continued life-sustaining interventions. EPs should also help the surrogate and family understand that palliative care addresses comfort needs of the patient including adequate treatment for pain, dyspnea, or anxiety. Part I of this communications model reviews determination of decision-making capacity, surrogacy laws, and advance directives, including legal definitions and application of these steps; Part II (which will appear in a future issue of AEM) covers communication moving from resuscitative to end-of-life and palliative treatment. EPs should recognize acute devastating illness or injuries, when appropriate, as opportunities to initiate end-of-life discussions and to implement shared decisions. © 2012 by the Society for Academic Emergency Medicine.

Naturally weathered feldspar surfaces in the Navajo Sandstone aquifer, Black Mesa, Arizona: Electron microscopic characterization

USGS Publications Warehouse

Zhu, Chen; Veblen, D.R.; Blum, A.E.; Chipera, S.J.

2006-01-01

Naturally weathered feldspar surfaces in the Jurassic Navajo Sandstone at Black Mesa, Arizona, was characterized with high-resolution transmission and analytical electron microscope (HRTEM-AEM) and field emission gun scanning electron microscope (FEG-SEM). Here, we report the first HRTEM observation of a 10-nm thick amorphous layer on naturally weathered K-feldspar in currently slightly alkaline groundwater. The amorphous layer is probably deficient in K and enriched in Si. In addition to the amorphous layer, the feldspar surfaces are also partially coated with tightly adhered kaolin platelets. Outside of the kaolin coatings, feldspar grains are covered with a continuous 3-5 ??m thick layer of authigenic smectite, which also coats quartz and other sediment grains. Authigenic K-feldspar overgrowth and etch pits were also found on feldspar grains. These characteristics of the aged feldspar surfaces accentuate the differences in reactivity between the freshly ground feldspar powders used in laboratory experiments and feldspar grains in natural systems, and may partially contribute to the commonly observed apparent laboratory-field dissolution rate discrepancy. At Black Mesa, feldspars in the Navajo Sandstone are dissolving at ???105 times slower than laboratory rate at comparable temperature and pH under far from equilibrium condition. The tightly adhered kaolin platelets reduce the feldspar reactive surface area, and the authigenic K-feldspar overgrowth reduces the feldspar reactivity. However, the continuous smectite coating layer does not appear to constitute a diffusion barrier. The exact role of the amorphous layer on feldspar dissolution kinetics depends on the origin of the layer (leached layer versus re-precipitated silica), which is uncertain at present. However, the nanometer thin layer can be detected only with HRTEM, and thus our study raises the possibility of its wide occurrence in geological systems. Rate laws and proposed mechanisms should consider the possibility of this amorphous layer on feldspar surface. ?? 2006 Elsevier Inc. All rights reserved.

New Radiolarian Age Constraints on the Emplacement History of the Manipur Ophiolitic Complex, India: the Timing of 'soft Collision'

NASA Astrophysics Data System (ADS)

Kachovich, S.; Aitchison, J. C.; Lokho, K.; Stojanovic, D.

2016-12-01

The Manipur Ophiolite complex in the Indo-Burman ranges is characterised by a north-south trending belt of ophiolitic and related oceanic volcanic and sedimentary rocks. The ophiolite is considered to have formed in Jurassic time as part of an intra-oceanic subduction zone. It was subsequently emplaced onto the continental margin of India. Although the ophiolite is extensively disrupted, well-exposed outcrops exist in new road cuttings. We present new results from investigations of associated oceanic pelagic sequences amongst which radiolarian microfossils help to constrain the timing for the emplacement event. Pelagic sediments assigned to the Disang Formation that crop out near Khamasom village, west of Ukhrul city are characterised by extensive fault-bounded packages of reddish-coloured, radiolarian-bearing mudstones. They yield abundant well-preserved, late Palaeocene to early Eocene radiolarians. As the ophiolitic rocks are thrust over these radiolarian-bearing sediments, they provide a precise biostratigraphic maximum age with which to constrain any ophiolite emplacement event. Elsewhere along the length of the Indus-Yarlung Tsangpo suture zone from NW India (Spongtang, Ladakh) in the west as well as at Zhongba, Sangdanlin and Gyantse across Tibet, correlative radiolarian faunas provide similar age constraints suggesting that this event was broadly coeval. Collision of an intra-oceanic island arc system with northern margin of the Indian continent over such an extensive strike length must be of regional significance. Moreover, given that this was an intra-Tethyan system it's collision (the `soft-collision' postulated by Curray et al. 1982) must pre-date later (hard) continent-continent collision. Reference: Curray, J.R., Emmel, F.J., Moore, D.G., Raitt, R.W., 1982. Structure, tectonics, and geological history of the northeastern Indian Ocean. In; Nairn, A.E.M. The Ocean Basins and Margins vol. 6: 399-450, Plenum Press.

Development and validation of a gas chromatography/ion trap-mass spectrometry method for simultaneous quantification of cocaine and its metabolites benzoylecgonine and norcocaine: application to the study of cocaine metabolism in human primary cultured renal cells.

PubMed

Valente, Maria João; Carvalho, Félix; Bastos, M Lourdes; Carvalho, Márcia; de Pinho, Paula Guedes

2010-11-15

Acute renal failure is a common finding in cocaine abusers. While cocaine metabolism may contribute to its nephrotoxic mechanisms, its pharmacokinetics in kidney cells is hitherto to be clarified. Primary cultures of human proximal tubular cells (HPTCs) provide a well-characterized in vitro model, phenotypically representative of HPTCs in vivo. Thus, the present work describes the first sensitive gas chromatography/ion trap-mass spectrometry (GC/IT-MS) method for measurement of cocaine and its metabolites benzoylecgonine (BE) and norcocaine (NCOC) using a primary culture of HPTCs as cellular matrix, following solid phase extraction (SPE) and derivatization with N-methyl-N-(trimethylsilyl)trifluoroacetamide (MSTFA). The application of this methodology also enables the identification of two other cocaine metabolites: ecgonine methyl ester (EME) and anhydroecgonine methyl ester (AEME). The validation of the method was performed through the evaluation of selectivity, linearity, precision and accuracy, limit of detection (LOD), and limit of quantification (LOQ). Its applicability was demonstrated through the quantification of cocaine, BE and NCOC in primary cultured HPTCs after incubation, at physiological conditions, with 1 mM cocaine for 72 h. The developed GC/IT-MS method was found to be linear (r² > 0.99). The intra-day precision varied between 3.6% and 13.5% and the values of accuracy between 92.7% and 111.9%. The LOD values for cocaine, BE and NCOC were 0.97±0.09, 0.40±0.04 and 20.89±1.81 ng/mL, respectively, and 3.24±0.30, 1.34±0.14 and 69.62±6.05 ng/mL as LOQ values. Copyright © 2010 Elsevier B.V. All rights reserved.

In situ Expression of Functional Genes Reveals Nitrogen Cycling at High Temperatures in Terrestrial Hydrothermal Systems

NASA Astrophysics Data System (ADS)

Loiacono, S. T.; Meyer-Dombard, D. R.

2011-12-01

An essential element for life, nitrogen occurs in all living organisms and is critical for the synthesis of amino acids, proteins, nucleic acids, and other forms of biomass. Thus, nitrogen cycling likely plays a vital role in microbial metabolic processes as well as nutrient availability. For microorganisms in "extreme" environments, this means developing adaptations that allow them to survive in harsh conditions and still perform the metabolisms essential to sustain life. Recent studies have screened biofilms and thermal sediments of Yellowstone National Park (YNP) thermal features for the presence of nifH genes, which code for a key enzyme in the nitrogen fixation process [1-4]. Furthermore, analysis of nitrogen isotopes in biofilms across a temperature and chemical gradient revealed that nitrogen fixation likely varies across the chemosynthetic/photosynthetic ecotone [5]. Although research has evaluated and confirmed the presence of nifH genes in various thermophilic microbial communities, the existence of a gene in the DNA of an organism does not verify its use. Instead, other methods, such as culturing, isotope tracer assays, and gene expression studies are required to provide direct evidence of biological nitrogen fixation. Culturing and isotope tracer approaches have successfully revealed high-temperature biological nitrogen fixation in both marine hydrothermal vent microbial communities [6] and in acidic, terrestrial hydrothermal sediment [3]. Transcriptomics-based techniques (using mRNA extracted from samples to confirm in situ expression of targeted genes) have been much more limited in number, and only a few studies have, to date, investigated in situ expression of the nifH gene in thermophilic microbial communities [2, 7]. This study explores the presence and expression of nifH genes in several features of the Lower Geyser Basin (LGB) of YNP. Nucleic acids from chemosynthetic and photosynthetic microbial communities were extracted and then amplified using (reverse-transcription) polymerase chain reaction to identify the presence and expression of nifH genes, and resultant (RT-)PCR product was cloned and sequenced. Results reveal high-temperature in situ expression of nifH in select LGB features [7] which is, to the authors' knowledge, the first direct evidence of nifH transcription in the chemosynthetic zones of terrestrial hydrothermal systems. Results also indicate the presence of novel nifH sequences and allow phylogenetic comparison of nifH genes along geochemical gradients within individual hot spring features and between various thermal features in the LGB. Collectively, these results provide evidence for microbial adaptations that have led to the ability to support basic metabolic processes under "extreme" conditions. [1] Hall et al., 2008. AEM 74: 4910-4922. [2] Steunou et al., 2008. The ISME Journal 2: 364-378. [3] Hamilton et al., 2011. Microb Ecol DOI 10.1007/s00248-011-9824-9. [4] Raymond et al., 2008. EOS Trans AGU. Abstract B14A-03. [5] Havig et al., 2010. J Geophys Res-Biogeo 116: G01005. [6] Mehta & Baross, 2006. Science 314: 1783-1786. [7] Loiacono et al., 2011. Submitted FEMS Microbiol Ecol.