Characterization of aerodynamic drag force on single particles: Final report
Kale, S.R.
1987-10-01
An electrodynamic balance was used to measure the drag coefficient and also to record the size and shape of spheres, and coal and oil shale particles (100 ..mu..m to 200 ..mu..m in size). The electrodynamic balance consisted of a central, and two end electrodes. The resulting electric field stably suspended a charged particle. A suspended particle, back illuminated by a light emitting diode, was viewed by a video camera. The image was analyzed for particle position control and was calibrated to give the diameter of spheres, or the area equivalent diameter of nonspherical particles. The drag coefficient was calculated from the air velocity and the dc voltage required to keep the particle at the balance center. The particle Reynolds number varied from 0.2 to 13. Three particles each of coal and oil shale were captured and photographed by a scanning electron microscope and the motion of all the particles was recorded on video tape. Drag coefficient vs Reynolds number data for spheres agreed well with correlations. Data for thirteen particles each of coal and oil shale indicated a power law relationship between drag coefficient and Reynolds number. All these particles exhibited higher drag than spheres and were also observed to rotate. The rotation, however, did not affect the drag coefficient. The choice of characteristic dimension affects the drag characteristics of oil shale more strongly than for coal, owing to the flake-like shape of oil shale. 38 figs., 5 tabs.
Aerodynamic drag on intermodal railcars
NASA Astrophysics Data System (ADS)
Kinghorn, Philip; Maynes, Daniel
2014-11-01
The aerodynamic drag associated with transport of commodities by rail is becoming increasingly important as the cost of diesel fuel increases. This study aims to increase the efficiency of intermodal cargo trains by reducing the aerodynamic drag on the load carrying cars. For intermodal railcars a significant amount of aerodynamic drag is a result of the large distance between loads that often occurs and the resulting pressure drag resulting from the separated flow. In the present study aerodynamic drag data have been obtained through wind tunnel testing on 1/29 scale models to understand the savings that may be realized by judicious modification to the size of the intermodal containers. The experiments were performed in the BYU low speed wind tunnel and the test track utilizes two leading locomotives followed by a set of five articulated well cars with double stacked containers. The drag on a representative mid-train car is measured using an isolated load cell balance and the wind tunnel speed is varied from 20 to 100 mph. We characterize the effect that the gap distance between the containers and the container size has on the aerodynamic drag of this representative rail car and investigate methods to reduce the gap distance.
NASA Astrophysics Data System (ADS)
Nwankwo, Victor U. J.; Chakrabarti, Sandip Kumar; Weigel, Robert
2016-07-01
Atmospheric drag is the strongest force perturbing the motion of satellites in low Earth orbits LEO, and could cause re-entry of satellites, difficulty in identifying and tracking of the satellites and other space objects, manuvering and prediction of lifetime and re-entry. Solar activities influence the temperature, density and composition of the upper atmosphere. These effects thus strongly depend on the phase of a solar cycle. The frequency of intense flares and storms increase during solar maximum. Heating up of the atmosphere causes its expansion eventually leading to accelerated drag of orbiting satellites, especially those in LEO. In this paper, we present the model of the atmospheric drag effect on the trajectory of hypothetical LEO satellites of different ballistic coefficients. We investigate long-term trend of atmospheric drag on LEO satellites due to solar forcing induced atmospheric perturbations and heating at different phases of the solar cycle, and during interval of strong geomagnetic disturbances or storms. We show the dependence of orbital decay on severity of both the solar cycle and phase, and the extent of geomagnetic perturbations. The result of the model compares well with the observed decay profile of existing LEO satellites and provides a better understanding of the issue of the orbital decay. Our result may also be useful for selection of launch window of satellites for an extended lifetime in the orbit.
Aerodynamic drag in cycling: methods of assessment.
Debraux, Pierre; Grappe, Frederic; Manolova, Aneliya V; Bertucci, William
2011-09-01
When cycling on level ground at a speed greater than 14 m/s, aerodynamic drag is the most important resistive force. About 90% of the total mechanical power output is necessary to overcome it. Aerodynamic drag is mainly affected by the effective frontal area which is the product of the projected frontal area and the coefficient of drag. The effective frontal area represents the position of the cyclist on the bicycle and the aerodynamics of the cyclist-bicycle system in this position. In order to optimise performance, estimation of these parameters is necessary. The aim of this study is to describe and comment on the methods used during the last 30 years for the evaluation of the effective frontal area and the projected frontal area in cycling, in both laboratory and actual conditions. Most of the field methods are not expensive and can be realised with few materials, providing valid results in comparison with the reference method in aerodynamics, the wind tunnel. Finally, knowledge of these parameters can be useful in practice or to create theoretical models of cycling performance. PMID:21936289
Exploring the Aerodynamic Drag of a Moving Cyclist
ERIC Educational Resources Information Center
Theilmann, Florian; Reinhard, Christopher
2016-01-01
Although the physics of cycling itself is a complex mixture of aerodynamics, physiology, mechanics, and heuristics, using cycling as a context for teaching physics has a tradition of certainly more than 30 years. Here, a possible feature is the discussion of the noticeable resistant forces such as aerodynamic drag and the associated power…
Aerodynamic Drag and Drag Reduction: Energy and Energy Savings (Invited)
NASA Technical Reports Server (NTRS)
Wood, Richard M.
2003-01-01
An assessment of the role of fluid dynamic resistance and/or aerodynamic drag and the relationship to energy use in the United States is presented. Existing data indicates that up to 25% of the total energy consumed in the United States is used to overcome aerodynamic drag, 27% of the total energy used in the United States is consumed by transportation systems, and 60% of the transportation energy or 16% of the total energy consumed in the United States is used to overcome aerodynamic drag in transportation systems. Drag reduction goals of 50% are proposed and discussed which if realized would produce a 7.85% total energy savings. This energy savings correlates to a yearly cost savings in the $30Billion dollar range.
NASA Astrophysics Data System (ADS)
Rajagopal, Krishna; Sadofyev, Andrey V.
2015-10-01
We provide a holographic evaluation of novel contributions to the drag force acting on a heavy quark moving through strongly interacting plasma. The new contributions are chiral in the sense that they act in opposite directions in plasmas containing an excess of left- or right-handed quarks. The new contributions are proportional to the coefficient of the axial anomaly, and in this sense also are chiral. These new contributions to the drag force act either parallel to or antiparallel to an external magnetic field or to the vorticity of the fluid plasma. In all these respects, these contributions to the drag force felt by a heavy quark are analogous to the chiral magnetic effect (CME) on light quarks. However, the new contribution to the drag force is independent of the electric charge of the heavy quark and is the same for heavy quarks and antiquarks, meaning that these novel effects do not in fact contribute to the CME current. We show that although the chiral drag force can be non-vanishing for heavy quarks that are at rest in the local fluid rest frame, it does vanish for heavy quarks that are at rest in a suitably chosen frame. In this frame, the heavy quark at rest sees counterpropagating momentum and charge currents, both proportional to the axial anomaly coefficient, but feels no drag force. This provides strong concrete evidence for the absence of dissipation in chiral transport, something that has been predicted previously via consideration of symmetries. Along the way to our principal results, we provide a general calculation of the corrections to the drag force due to the presence of gradients in the flowing fluid in the presence of a nonzero chemical potential. We close with a consequence of our result that is at least in principle observable in heavy ion collisions, namely an anticorrelation between the direction of the CME current for light quarks in a given event and the direction of the kick given to the momentum of all the heavy quarks and
Switchable and Tunable Aerodynamic Drag on Cylinders
NASA Astrophysics Data System (ADS)
Guttag, Mark; Lopez Jimenez, Francisco; Reis, Pedro
2015-11-01
We report results on the performance of Smart Morphable Surfaces (Smporhs) that can be mounted onto cylindrical structures to actively reduce their aerodynamic drag. Our system comprises of an elastomeric thin shell with a series of carefully designed subsurface cavities that, once depressurized, lead to a dramatic deformation of the surface topography, on demand. Our design is inspired by the morphology of the giant cactus (Carnegiea gigantea) which possesses an array of axial grooves, which are thought to help reduce aerodynamic drag, thereby enhancing the structural robustness of the plant under wind loading. We perform systematic wind tunnel tests on cylinders covered with our Smorphs and characterize their aerodynamic performance. The switchable and tunable nature of our system offers substantial advantages for aerodynamic performance when compared to static topographies, due to their operation over a wider range of flow conditions.
Switchable and Tunable Aerodynamic Drag on Cylinders
NASA Astrophysics Data System (ADS)
Guttag, Mark; Lopéz Jiménez, Francisco; Upadhyaya, Priyank; Kumar, Shanmugam; Reis, Pedro
We report results on the performance of Smart Morphable Surfaces (Smporhs) that can be mounted onto cylindrical structures to actively reduce their aerodynamic drag. Our system comprises of an elastomeric thin shell with a series of carefully designed subsurface cavities that, once depressurized, lead to a dramatic deformation of the surface topography, on demand. Our design is inspired by the morphology of the giant cactus (Carnegiea gigantea) which possesses an array of axial grooves, thought to help reduce aerodynamic drag, thereby enhancing the structural robustness of the plant under wind loading. We perform systematic wind tunnel tests on cylinders covered with our Smorphs and characterize their aerodynamic performance. The switchable and tunable nature of our system offers substantial advantages for aerodynamic performance when compared to static topographies, due to their operation over a wider range of flow conditions.
Method of reducing drag in aerodynamic systems
NASA Technical Reports Server (NTRS)
Hrach, Frank J. (Inventor)
1993-01-01
In the present method, boundary layer thickening is combined with laminar flow control to reduce drag. An aerodynamic body is accelerated enabling a ram turbine on the body to receive air at velocity V sub 0. The discharge air is directed over an aft portion of the aerodynamic body producing boundary layer thickening. The ram turbine also drives a compressor by applying torque to a shaft connected between the ram turbine and the compressor. The compressor sucks in lower boundary layer air through inlets in the shell of the aircraft producing laminar flow control and reducing drag. The discharge from the compressor is expanded in a nozzle to produce thrust.
DOE Project on Heavy Vehicle Aerodynamic Drag
McCallen, R; Salari, K; Ortega, J; Castellucci, P; Pointer, D; Browand, F; Ross, J; Storms, B
2007-01-04
Class 8 tractor-trailers consume 11-12% of the total US petroleum use. At highway speeds, 65% of the energy expenditure for a Class 8 truck is in overcoming aerodynamic drag. The project objective is to improve fuel economy of Class 8 tractor-trailers by providing guidance on methods of reducing drag by at least 25%. A 25% reduction in drag would present a 12% improvement in fuel economy at highway speeds, equivalent to about 130 midsize tanker ships per year. Specific goals include: (1) Provide guidance to industry in the reduction of aerodynamic drag of heavy truck vehicles; (2) Develop innovative drag reducing concepts that are operationally and economically sound; and (3) Establish a database of experimental, computational, and conceptual design information, and demonstrate the potential of new drag-reduction devices. The studies described herein provide a demonstration of the applicability of the experience developed in the analysis of the standard configuration of the Generic Conventional Model. The modeling practices and procedures developed in prior efforts have been applied directly to the assessment of new configurations including a variety of geometric modifications and add-on devices. Application to the low-drag 'GTS' configuration of the GCM has confirmed that the error in predicted drag coefficients increases as the relative contribution of the base drag resulting from the vehicle wake to the total drag increases and it is recommended that more advanced turbulence modeling strategies be applied under those circumstances. Application to a commercially-developed boat tail device has confirmed that this restriction does not apply to geometries where the relative contribution of the base drag to the total drag is reduced by modifying the geometry in that region. Application to a modified GCM geometry with an open grille and radiator has confirmed that the underbody flow, while important for underhood cooling, has little impact on the drag coefficient of
ERIC Educational Resources Information Center
Weltner, Klaus
1990-01-01
Describes some experiments showing both qualitatively and quantitatively that aerodynamic lift is a reaction force. Demonstrates reaction forces caused by the acceleration of an airstream and the deflection of an airstream. Provides pictures of demonstration apparatus and mathematical expressions. (YP)
Methods of reducing vehicle aerodynamic drag
Sirenko V.; Rohatgi U.
2012-07-08
A small scale model (length 1710 mm) of General Motor SUV was built and tested in the wind tunnel for expected wind conditions and road clearance. Two passive devices, rear screen which is plate behind the car and rear fairing where the end of the car is aerodynamically extended, were incorporated in the model and tested in the wind tunnel for different wind conditions. The conclusion is that rear screen could reduce drag up to 6.5% and rear fairing can reduce the drag by 26%. There were additional tests for front edging and rear vortex generators. The results for drag reduction were mixed. It should be noted that there are aesthetic and practical considerations that may allow only partial implementation of these or any drag reduction options.
Exploring the aerodynamic drag of a moving cyclist
NASA Astrophysics Data System (ADS)
Theilmann, Florian; Reinhard, Christopher
2016-01-01
Although the physics of cycling itself is a complex mixture of aerodynamics, physiology, mechanics, and heuristics, using cycling as a context for teaching physics has a tradition of certainly more than 30 years. Here, a possible feature is the discussion of the noticeable resistant forces such as aerodynamic drag and the associated power consumption of cycling. We use an energy-based approach to model the power input for driving a bike at a constant speed. This approach uses a numerical simulation of the slowing down of a bike moving without pedaling which is implementable with standard spreadsheet software. The simulation can be compared directly to simple measurements with real bikes as well as to an analytic solution of the underlying differential equation. It is possible to derive realistic values for the aerodynamic drag coefficient {{c}\\text{D}} and the total power consumption within a secondary physics course. We also report experiences from teaching such a course to class 8 students.
Miniature drag force anemometer
NASA Technical Reports Server (NTRS)
Krause, L. N.; Fralick, G. C.
1977-01-01
A miniature drag force anemometer is described which is capable of measuring dynamic velocity head and flow direction. The anemometer consists of a silicon cantilevered beam 2.5 mm long, 1.5 mm wide, and 0.25 mm thick with an integrated diffused strain gage bridge, located at the base of the beam, as the force measuring element. The dynamics of the beam are like that of a second order system with a natural frequency of about 42 kHz and a damping coefficient of 0.007. The anemometer can be used in both forward and reversed flow. Measured flow characteristics up to Mach 0.6 are presented along with application examples including turbulence measurements.
Measuring the Drag Force on a Falling Ball
ERIC Educational Resources Information Center
Cross, Rod; Lindsey, Crawford
2014-01-01
The effect of the aerodynamic drag force on an object in flight is well known and has been described in this and other journals many times. At speeds less than about 1 m/s, the drag force on a sphere is proportional to the speed and is given by Stokes' law. At higher speeds, the drag force is proportional to the velocity squared and is…
Reference values and improvement of aerodynamic drag in professional cyclists.
García-López, Juan; Rodríguez-Marroyo, José Antonio; Juneau, Carl-Etienne; Peleteiro, José; Martínez, Alfredo Córdova; Villa, José Gerardo
2008-02-01
The aims of this study were to measure the aerodynamic drag in professional cyclists, to obtain aerodynamic drag reference values in static and effort positions, to improve the cyclists' aerodynamic drag by modifying their position and cycle equipment, and to evaluate the advantages and disadvantages of these modifications. The study was performed in a wind tunnel with five professional cyclists. Four positions were assessed with a time-trial bike and one position with a standard racing bike. In all positions, aerodynamic drag and kinematic variables were recorded. The drag area for the time-trial bike was 31% higher in the effort than static position, and lower than for the standard racing bike. Changes in the cyclists' position decreased the aerodynamic drag by 14%. The aero-helmet was not favourable for all cyclists. The reliability of aerodynamic drag measures in the wind tunnel was high (r > 0.96, coefficient of variation < 2%). In conclusion, we measured and improved the aerodynamic drag in professional cyclists. Our results were better than those of other researchers who did not assess aerodynamic drag during effort at race pace and who employed different wheels. The efficiency of the aero-helmet, and the validity, reliability, and sensitivity of the wind tunnel and aerodynamic field testing were addressed. PMID:17943597
Parachute drag and radial force
Purvis, J.W.
1986-01-01
This paper presents a combination of old and new wind tunnel data in a format which illustrates the effects of inflated diameter, geometric porosity, reefing line length, suspension line length, number of gores, and number of ribbons on parachute drag. A new definition of radial force coefficient is presented, as well as a universal drag curve for flat circular and conical parachutes.
Fuel Savings and Aerodynamic Drag Reduction from Rail Car Covers
NASA Technical Reports Server (NTRS)
Storms, Bruce; Salari, Kambiz; Babb, Alex
2008-01-01
The potential for energy savings by reducing the aerodynamic drag of rail cars is significant. A previous study of aerodynamic drag of coal cars suggests that a 25% reduction in drag of empty cars would correspond to a 5% fuel savings for a round trip [1]. Rail statistics for the United States [2] report that approximately 5.7 billion liters of diesel fuel were consumed for coal transportation in 2002, so a 5% fuel savings would total 284 million liters. This corresponds to 2% of Class I railroad fuel consumption nationwide. As part of a DOE-sponsored study, the aerodynamic drag of scale rail cars was measured in a wind tunnel. The goal of the study was to measure the drag reduction of various rail-car cover designs. The cover designs tested yielded an average drag reduction of 43% relative to empty cars corresponding to an estimated round-trip fuel savings of 9%.
Miniature drag-force anemometer
NASA Technical Reports Server (NTRS)
Krause, L. N.; Fralick, G. C.
1981-01-01
A miniature drag force anemometer is described which is capable of measuring unsteady as well as steady state velocity head and flow direction. It consists of a cantilevered beam with strain gages located at the base of the beam as the force measuring element. The dynamics of the beam are like those of lightly damped second order system with a natural frequency as high as 40 kilohertz depending on beam geometry and material. The anemometer is used in both forward and reversed flow. Anemometer characteristics and several designs are presented along with discussions of several applications.
Miniature drag-force anemometer
NASA Technical Reports Server (NTRS)
Krause, L. N.; Fralick, G. C.
1981-01-01
A miniature drag-force anemometer is described which is capable of measuring unsteady as well as steady-state velocity head and flow direction. It consists of a cantilevered beam with strain gages located at the base of the beam as the force measuring element. The dynamics of the beam are like those of a lightly damped second-order system with a natural frequency as high as 40 kilohertz depending on beam geometry and material. The anemometer can be used in both forward and reversed flow. Anemometer characteristics and several designs are presented along with discussions of several applications.
Miniature drag-force anemometer
NASA Technical Reports Server (NTRS)
Krause, L. N.; Fralick, G. C.
1977-01-01
A miniature drag-force anemometer is described which is capable of measuring dynamic velocity head and flow direction. The anemometer consists of a silicon cantilever beam 2.5 mm long, 1.5 mm wide, and 0.25 mm thick with an integrated diffused strain-gage bridge, located at the base of the beam, as the force measuring element. The dynamics of the beam are like those of a second-order system with a natural frequency of about 42 kHz and a damping coefficient of 0.007. The anemometer can be used in both forward and reversed flow. Measured flow characteristics up to Mach 0.6 are presented along with application examples including turbulence measurements.
Vertical variations of coral reef drag forces
NASA Astrophysics Data System (ADS)
Asher, Shai; Niewerth, Stephan; Koll, Katinka; Shavit, Uri
2016-05-01
Modeling flow in a coral reef requires a closure model that links the local drag force to the local mean velocity. However, the spatial flow variations make it difficult to predict the distribution of the local drag. Here we report on vertical profiles of measured drag and velocity in a laboratory reef that was made of 81 Pocillopora Meandrina colony skeletons, densely arranged along a tilted flume. Two corals were CT-scanned, sliced horizontally, and printed using a 3-D printer. Drag was measured as a function of height above the bottom by connecting the slices to drag sensors. Profiles of velocity were measured in-between the coral branches and above the reef. Measured drag of whole colonies shows an excellent agreement with previous field and laboratory studies; however, these studies never showed how drag varies vertically. The vertical distribution of drag is reported as a function of flow rate and water level. When the water level is the same as the reef height, Reynolds stresses are negligible and the drag force per unit fluid mass is nearly constant. However, when the water depth is larger, Reynolds stress gradients become significant and drag increases with height. An excellent agreement was found between the drag calculated by a momentum budget and the measured drag of the individual printed slices. Finally, we propose a modified formulation of the drag coefficient that includes the normal dispersive stress term and results in reduced variations of the drag coefficient at the cost of introducing an additional coefficient.
Drop tower with no aerodynamic drag
NASA Technical Reports Server (NTRS)
Kendall, J. M., Jr.
1981-01-01
Cooling air accelerated to match velocity of falling object eliminates drag. 3 meter drop tower with suction fan and specific geometry causes air to accelerate downward at 1 g. Although cooling of molten material released from top is slow because surrounding air moves with it, drop remains nearly spherical.
Aerodynamic Drag Reduction Apparatus For Wheeled Vehicles In Ground Effect
Ortega, Jason M.; Salari, Kambiz
2005-12-13
An apparatus for reducing the aerodynamic drag of a wheeled vehicle in a flowstream, the vehicle having a vehicle body and a wheel assembly supporting the vehicle body. The apparatus includes a baffle assembly adapted to be positioned upstream of the wheel assembly for deflecting airflow away from the wheel assembly so as to reduce the incident pressure on the wheel assembly.
Aerodynamic drag reduction by vertical splitter plates
NASA Astrophysics Data System (ADS)
Gilliéron, Patrick; Kourta, Azeddine
2010-01-01
The capacity of vertical splitter plates placed at the front or the rear of a simplified car geometry to reduce drag, with and without skew angle, is investigated for Reynolds numbers between 1.0 × 106 and 1.6 × 106. The geometry used is a simplified geometry to represent estate-type vehicles, for the rear section, and MPV-type vehicle. Drag reductions of nearly 28% were obtained for a zero skew angle with splitter plates placed at the front of models of MPV or utility vehicles. The results demonstrate the advantage of adapting the position and orientation of the splitter plates in the presence of a lateral wind. All these results confirm the advantage of this type of solution, and suggest that this expertise should be used in the automotive field to reduce consumption and improve dynamic stability of road vehicles.
Nonequilibrium forces between dragged ultrasoft colloids.
Singh, Sunil P; Winkler, Roland G; Gompper, Gerhard
2011-10-01
The dynamical deformation of ultrasoft colloids as well as their dynamic frictional forces are numerically investigated, when one colloid is dragged past another at constant velocity. Hydrodynamic interactions are captured by a particle-based mesoscopic simulation method. At vanishing relative velocity, the equilibrium repulsive force-distance curve is obtained. At large drag velocities, in contrast, we find an apparent attractive force for departing colloids along the dragging direction. The deformation, in the close encounter of colloids, and the energy dissipation are examined as a function of the drag velocity and their separation. PMID:22107322
Aerodynamics of Drag Reduction Devices for Semi-Trucks
NASA Astrophysics Data System (ADS)
Ortega, Jason; Salari, Kambiz
2014-11-01
An increasing number of semi-trucks throughout the United States are being retrofitted with aerodynamic drag reduction devices to improve the vehicle fuel economy. Such devices typically include both trailer skirts and boattails to mitigate trailer underbody drag and base drag, respectively. Since full-scale measurements of the device performance are especially prone to experimental noise due to the effects of the driver, route, payload, or atmospheric conditions, more precise data must be obtained within a wind tunnel. In this experimental study, the wind-averaged drag coefficient is measured for a detailed 1/8th scale semi-truck model. The Reynolds number based upon the vehicle width is 1.7e6. A number of trailer skirt and boattail device configurations are considered, as well as the effects of the boattail deflection angle. The results of this study demonstrate that a combination of a trailer skirt and boattail reduces the aerodynamic drag of a semi-truck by as much as 25%. If such a combination were applied to each of the semi-trucks throughout the United States, several billion dollars in fuel savings could be achieved each year. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-657810.
Reducing Aerodynamic Drag on Empty Open Cargo Vehicles
NASA Technical Reports Server (NTRS)
Ross, James C.; Storms, Bruce L.; Dzoan, Dan
2009-01-01
Some simple structural modifications have been demonstrated to be effective in reducing aerodynamic drag on vehicles that have empty open cargo bays. The basic idea is to break up the airflow in a large open cargo bay by inserting panels to divide the bay into a series of smaller bays. In the case of a coal car, this involves inserting a small number (typically between two and four) of vertical full-depth or partial-depth panels.
An Aerodynamic Assessment of Micro-Drag Generators (MDGs)
NASA Technical Reports Server (NTRS)
Bauer, Steven X. S.
1998-01-01
Commercial transports as well as fighter aircraft of the future are being designed with very low drag (friction and pressure). Concurrently, commuter airports are being built or envisioned to be built in the centers of metropolitan areas where shorter runways and/or reduced noise footprints on takeoff and landing are required. These requirements and the fact that drag is lower on new vehicles than on older aircraft have resulted in vehicles that require a large amount of braking force (from landing-gear brakes, spoilers, high-lift flaps, thrust reversers, etc.). Micro-drag generators (MDGs) were envisioned to create a uniformly distributed drag force along a vehicle by forcing the flow to separate on the aft-facing surface of a series of deployable devices, thus, generating drag. The devices are intended to work at any speed and for any type of vehicle (aircraft, ground vehicles, sea-faring vehicles). MDGs were applied to a general aviation wing and a representative fuselage shape and tested in two subsonic wind tunnels. The results showed increases in drag of 2 to 6 times that of a "clean" configuration.
Aerodynamic drag control by pulsed jets on simplified car geometry
NASA Astrophysics Data System (ADS)
Gilliéron, Patrick; Kourta, Azeddine
2013-02-01
Aerodynamic drag control by pulsed jets is tested in a wind tunnel around a simplified car geometry named Ahmed body with a rear slant angle of 35°. Pulsed jet actuators are located 5 × 10-3 m from the top of the rear window. These actuators are produced by a pressure difference ranging from 1.5 to 6.5 × 105 Pa. Their excitation frequency can vary between 10 and 550 Hz. The analysis of the control effects is based on wall visualizations, aerodynamic drag coefficient measurements, and the velocity fields obtained by 2D PIV measurements. The maximum drag reduction is 20 % and is obtained for the excitation frequency F j = 500 Hz and for the pressure difference ∆ P = 1.5 × 105 Pa. This result is linked with a substantial reduction in the transverse development of the longitudinal vortex structures coming from the left and right lateral sides of the rear window, with a displacement of the vortex centers downstream and with a decrease in the transverse rotational absolute values of these structures.
FY2003 Annual Report: DOE Project on Heavy Vehicle Aerodynamic Drag
McCallen, R C; Salari, K; Ortega, J; DeChant, L J; Roy, C J; Payne, J J; Hassan, B; Pointer, W D; Browand, F; Hammache, M; Hsu, T; Ross, J; Satran, D; Heineck, J; Walker, S; Yaste, D; Englar, R; Leonard, A; Rubel, M; Chatelain, P
2003-10-24
Objective: {sm_bullet} Provide guidance to industry in the reduction of aerodynamic drag of heavy truck vehicles. {sm_bullet} Establish a database of experimental, computational, and conceptual design information, and demonstrate potential of new drag-reduction devices.
Investigation of Tractor Base Bleeding for Heavy Vehicle Aerodynamic Drag Reduction
Ortega, J; Salari, K; Storms, B
2007-10-25
One of the main contributors to the aerodynamic drag of a heavy vehicle is tractor-trailer gap drag, which arises when the vehicle operates within a crosswind. Under this operating condition, freestream flow is entrained into the tractor-trailer gap, imparting a momentum exchange to the vehicle and subsequently increasing the aerodynamic drag. While a number of add-on devices, including side extenders, splitter plates, vortex stabilizers, and gap sealers, have been previously tested to alleviate this source of drag, side extenders remain the primary add-on device of choice for reducing tractor-trailer gap drag. However, side extenders are not without maintenance and operational issues. When a heavy vehicle pivots sharply with respect to the trailer, as can occur during loading or unloading operations, the side extenders can become crushed against the trailer. Consequently, fleet operators are forced to incur additional costs to cover the repair or replacement of the damaged side extenders. This issue can be overcome by either shortening the side extenders or by devising an alternative drag reduction concept that can perform just as effectively as side extenders. To explore such a concept, we investigate tractor base bleeding as a means of reducing gap drag. Wind tunnel measurements are made on a 1:20 scale heavy vehicle model at a vehicle width-based Reynolds number of 420,000. The tractor bleeding flow, which is delivered through a porous material embedded within the tractor base, is introduced into the tractor-trailer gap at bleeding coefficients ranging from 0.0-0.018. To determine the performance of tractor base bleeding under more realistic operating conditions, computational fluid dynamics simulations are performed on a full-scale heavy vehicle within a crosswind for bleeding coefficients ranging from 0.0-0.13.
Drag and lift forces in granular media
NASA Astrophysics Data System (ADS)
Guillard, F.; Forterre, Y.; Pouliquen, O.
2013-09-01
Forces exerted on obstacles moving in granular media are studied. The experiment consists in a horizontal cylinder rotating around the vertical axis in a granular medium. Both drag forces and lift forces experienced by the cylinder are measured. The first striking result is obtained during the first half rotation, before the cylinder crosses its wake. Despite the symmetry of the object, a strong lift force is measured, about 20 times the buoyancy. The scaling of this force is studied experimentally. The second remarkable observation is made after several rotations. The drag force dramatically drops and becomes independent of depth, showing that it no longer scales with the hydrostatic pressure. The rotation of the cylinder induces a structure in the packing, which screens the weight of the grains above
Drag-force regimes in granular impact
NASA Astrophysics Data System (ADS)
Tiwari, Mukesh; Mohan, T. R. Krishna; Sen, Surajit
2014-12-01
We study the penetration dynamics of a projectile incident normally on a substrate comprising of smaller granular particles in three-dimensions using the discrete element method. Scaling of the penetration depth is consistent with experimental observations for small velocity impacts. Our studies are consistent with the observation that the normal or drag force experienced by the penetrating grain obeys the generalized Poncelet law, which has been extensively invoked in understanding the drag force in the recent experimental data. We find that the normal force experienced by the projectile consists of position and kinetic-energy-dependent pieces. Three different penetration regimes are identified in our studies for low-impact velocities. The first two regimes are observed immediately after the impact and in the early penetration stage, respectively, during which the drag force is seen to depend on the kinetic energy. The depth dependence of the drag force becomes significant in the third regime when the projectile is moving slowly and is partially immersed in the substrate. These regimes relate to the different configurations of the bed: the initial loose surface packed state, fluidized bed below the region of impact, and the state after the crater formation commences.
Drag-force regimes in granular impact.
Tiwari, Mukesh; Mohan, T R Krishna; Sen, Surajit
2014-12-01
We study the penetration dynamics of a projectile incident normally on a substrate comprising of smaller granular particles in three-dimensions using the discrete element method. Scaling of the penetration depth is consistent with experimental observations for small velocity impacts. Our studies are consistent with the observation that the normal or drag force experienced by the penetrating grain obeys the generalized Poncelet law, which has been extensively invoked in understanding the drag force in the recent experimental data. We find that the normal force experienced by the projectile consists of position and kinetic-energy-dependent pieces. Three different penetration regimes are identified in our studies for low-impact velocities. The first two regimes are observed immediately after the impact and in the early penetration stage, respectively, during which the drag force is seen to depend on the kinetic energy. The depth dependence of the drag force becomes significant in the third regime when the projectile is moving slowly and is partially immersed in the substrate. These regimes relate to the different configurations of the bed: the initial loose surface packed state, fluidized bed below the region of impact, and the state after the crater formation commences. PMID:25615080
Gubser, Steven S.
2006-12-15
The AdS/CFT correspondence and a classical test string approximation are used to calculate the drag force on an external quark moving in a thermal plasma of N=4 super-Yang-Mills theory. This computation is motivated by the phenomenon of jet-quenching in relativistic heavy ion collisions.
Nonlinear drag force in dusty plasmas
Tsytovich, V.N.; De Angelis, U.; Ivlev, A.V.; Morfill, G.E.; Khrapak, S.
2005-11-15
The condition for large angle scattering in ion-grain collisions, which determine the nonlinear part of the ion drag force, coincides with the condition for the grain screening to be nonlinear (e{phi}/T{sub i}>1 where {phi} is the electrostatic grain potential and T{sub i} is the ion mean energy), a condition met in many laboratory experiments. A self-consistent treatment of the nonlinear ion-drag force therefore requires a correct treatment of nonlinear screening. A model to account for the nonlinearity is presented and the drag force calculated, showing that it can be substantially larger than that for linear screening. An important physical feature found in the present investigation is that nonlinear screening corresponds to almost full screening inside a finite radius and that large angle scattering occurs only inside this radius. The nonlinear ion-drag force is found to have a strong dependence on the grain size, ratio of ion to electron temperatures, and ion density.
Normal Force and Drag Force in Magnetorheological Finishing
Miao, C.; Shafrir, S.N.; Lambropoulos, J.C.; Jacobs, S.D.
2010-01-13
The material removal in magnetorheological finishing (MRF) is known to be controlled by shear stress, tau, which equals drag force, Fd, divided by spot area, As. However, it is unclear how the normal force, Fn, affects the material removal in MRF and how the measured ratio of drag force to normal force Fd/Fn, equivalent to coefficient of friction, is related to material removal. This work studies, for the first time for MRF, the normal force and the measured ratio Fd/Fn as a function of material mechanical properties. Experimental data were obtained by taking spots on a variety of materials including optical glasses and hard ceramics with a spot-taking machine (STM). Drag force and normal force were measured with a dual load cell. Drag force decreases linearly with increasing material hardness. In contrast, normal force increases with hardness for glasses, saturating at high hardness values for ceramics. Volumetric removal rate decreases with normal force across all materials. The measured ratio Fd/Fn shows a strong negative linear correlation with material hardness. Hard materials exhibit a low “coefficient of friction”. The volumetric removal rate increases with the measured ratio Fd/Fn which is also correlated with shear stress, indicating that the measured ratio Fd/Fn is a useful measure of material removal in MRF.
Hybrid approach to the ion drag force
Khrapak, S.A.; Ivlev, A.V.; Zhdanov, S.K.; Morfill, G.E.
2005-04-15
A detailed calculation of the ion drag force acting on a single grain in a collisionless Maxwellian plasma with an arbitrary velocity of the ion flow is carried out. The traditional binary collision approach to the problem is combined with the linear kinetic formalism. It is shown that for a pointlike particle the binary collision approach yields correct results provided that the effective plasma screening length is chosen appropriately. The correct choice follows from the self-consistent kinetic theory. On the other hand, the binary collision approach accounts consistently for the effects of finite grain size and grain charging. Taking these effects into account an expression for the ion drag force is obtained. Calculations are performed for a typical (exemplary) set of complex plasma parameters. The relevance for recent complex plasma experiments is briefly discussed.
Ion drag forces and magnetomechanical effect
Nedospasov, A. V. Nenova, N. V.
2010-11-15
Ion flows (ion drag forces) acting on macroscopic-size particles play a significant role in a plasma containing macroparticles. It is shown that ion drag forces can explain the magnetomechanical effect. The formula is derived for determining the dependence of the moment of the magnetomechanical effect on the type and pressure of the gas, tube radius, current, and magnetic field. This formula is in satisfactory agreement with experimental data for discharges in argon and neon with a relatively low magnetization of electron motion. For a high magnetization, the measured values of the moment of the magnetomechanical effect exceed the calculated values, which can be due to the effect of magnetic field nonuniformity and inhomogeneity of the plasma near the solenoid ends.
Aerodynamic drag reduction of a simplified squareback vehicle using steady blowing
NASA Astrophysics Data System (ADS)
Littlewood, R. P.; Passmore, M. A.
2012-08-01
A large contribution to the aerodynamic drag of a vehicle arises from the failure to fully recover pressure in the wake region, especially on squareback configurations. A degree of base pressure recovery can be achieved through careful shape optimisation, but the freedom of an automotive aerodynamicist to implement significant shape changes is limited by a variety of additional factors such styling, ergonomics and loading capacity. Active flow control technologies present the potential to create flow field modifications without the need for external shape changes and have received much attention in previous years within the aeronautical industry and, more recently, within the automotive industry. In this work the influence of steady blowing applied at a variety of angles on the roof trailing edge of a simplified ¼ scale squareback style vehicle has been investigated. Hot-wire anemometry, force balance measurements, surface pressure measurements and PIV have been used to investigate the effects of the steady blowing on the vehicle wake structures and the resulting body forces. The energy consumption of the steady jet is calculated and is used to deduce an aerodynamic drag power change. Results show that overall gains can be achieved; however, the large mass flow rate required restricts the applicability of the technique to road vehicles. Means by which the mass flow rate requirements of the jet may be reduced are discussed and suggestions for further work put forward.
Aerodynamic force by Lamb vector integrals in compressible flow
NASA Astrophysics Data System (ADS)
Mele, Benedetto; Tognaccini, Renato
2014-05-01
A new exact expression of the aerodynamic force acting on a body in steady high Reynolds number (laminar and turbulent) compressible flow is proposed. The aerodynamic force is obtained by integration of the Lamb vector field given by the cross product of vorticity times velocity. The result is obtained extending a theory developed for the incompressible case. A decomposition in lift and drag contribution is obtained in the two-dimensional case. The theory links the force generation to local flow properties, in particular to the Lamb vector field and to the kinetic energy. The theoretical results are confirmed analyzing numerical solutions obtained by a standard Reynolds Averaged Navier-Stokes solver. Results are discussed for the case of a two-dimensional airfoil in subsonic, transonic, and supersonic free stream conditions.
A method for the reduction of aerodynamic drag of road vehicles
NASA Technical Reports Server (NTRS)
Pamadi, Bandu N.; Taylor, Larry W.; Leary, Terrance O.
1990-01-01
A method is proposed for the reduction of the aerodynamic drag of bluff bodies, particularly for application to road transport vehicles. This technique consists of installation of panels on the forward surface of the vehicle facing the airstream. With the help of road tests, it was demonstrated that the attachment of proposed panels can reduce aerodynamic drag of road vehicles and result in significant fuel cost savings and conservation of energy resources.
NASA Technical Reports Server (NTRS)
Montoya, L. C.; Steers, L. L.
1974-01-01
Aerodynamic drag tests were performed on a conventional cab-over-engine tractor with a 45-foot trailer and five commercially available or potentially available add-on devices using the coast-down method. The tests ranged in velocity from approximately 30 miles per hour to 65 miles per hour and included some flow visualization. A smooth, level runway at Edwards Air Force Base was used for the tests, and deceleration measurements were taken with both accelerometers and stopwatches. An evaluation of the drag reduction results obtained with each of the five add-on devices is presented.
Yaste, David M; Salari, Kambiz; Hammache, Mustapha; Browand, Fred; Pointer, W. David; Ortega, Jason M.; McCallen, Rose; Walker, Stephen M; Heineck, James T; Hassan, Basil; Roy, Christopher John; Storms, B.; Satran, D.; Ross, James; Englar, Robert; Chatalain, Philippe; Rubel, Mike; Leonard, Anthony; Hsu, Tsu-Ya; DeChant, Lawrence Justin.
2004-06-01
At 70 miles per hour, overcoming aerodynamic drag represents about 65% of the total energy expenditure for a typical heavy truck vehicle. The goal of this US Department of Energy supported consortium is to establish a clear understanding of the drag producing flow phenomena. This is being accomplished through joint experiments and computations, leading to the smart design of drag reducing devices. This paper will describe our objective and approach, provide an overview of our efforts and accomplishments, and discuss our future direction.
McCallen, R; Salari, K; Ortega, J; DeChant, L; Hassan, B; Roy, C; Pointer, W; Browand, F; Hammache, M; Hsu, T; Leonard, A; Rubel, M; Chatalain, P; Englar, R; Ross, J; Satran, D; Heineck, J; Walker, S; Yaste, D; Storms, B
2004-06-17
At 70 miles per hour, overcoming aerodynamic drag represents about 65% of the total energy expenditure for a typical heavy truck vehicle. The goal of this US Department of Energy supported consortium is to establish a clear understanding of the drag producing flow phenomena. This is being accomplished through joint experiments and computations, leading to the 'smart' design of drag reducing devices. This paper will describe our objective and approach, provide an overview of our efforts and accomplishments, and discuss our future direction.
DOE Project on Heavy Vehicle Aerodynamic Drag FY 2005 Annual Report
McCallen, R C; Salari, K; Ortega, J; Castellucci, P; Eastwood, C; Paschkewitz, J; Pointer, W D; DeChant, L J; Hassan, B; Browand, F; Radovich, C; Merzel, T; Plocher, D; Ross, J; Storms, B; Heineck, J T; Walker, S; Roy, C J
2005-11-14
Class 8 tractor-trailers consume 11-12% of the total US petroleum use. At high way speeds, 65% of the energy expenditure for a Class 8 truck is in overcoming aerodynamic drag. The project objective is to improve fuel economy of Class 8 tractor-trailers by providing guidance on methods of reducing drag by at least 25%. A 25% reduction in drag would present a 12% improvement in fuel economy at highway speeds, equivalent to about 130 midsize tanker ships per year. Specific goals include: (1) Provide guidance to industry in the reduction of aerodynamic drag of heavy truck vehicles; and (2) Establish a database of experimental, computational, and conceptual design information, and demonstrate the potential of new drag-reduction devices.
Drag of the complete configuration aerodynamic considerations, 2
NASA Technical Reports Server (NTRS)
Roskam, J.
1975-01-01
A number of drag items are related to the performance of a complete aircraft configuration. First, the effect of fuselage camber, wing and nacelle incidence are discussed from a viewpoint of design decision making. Second, the effect of overall cruise drag on the design gross and empty weight of the airplane is discussed. Examples show that cruise drag can have a very important influence on total airplane weight. Third, the effects of usable cruise lift-to-drag ratio and wing loading are shown to be important. Finally several research needs relating to design of the complete configuration are reviewed.
Drag Force Anemometer Used in Supersonic Flow
NASA Technical Reports Server (NTRS)
Fralick, Gustave C.
1998-01-01
To measure the drag on a flat cantilever beam exposed transversely to a flow field, the drag force anemometer (beam probe) uses strain gauges attached on opposite sides of the base of the beam. This is in contrast to the hot wire anemometer, which depends for its operation on the variation of the convective heat transfer coefficient with velocity. The beam probe retains the high-frequency response (up to 100 kHz) of the hot wire anemometer, but it is more rugged, uses simpler electronics, is relatively easy to calibrate, is inherently temperature compensated, and can be used in supersonic flow. The output of the probe is proportional to the velocity head of the flow, 1/2 rho u(exp 2) (where rho is the fluid density and u is the fluid velocity). By adding a static pressure tap and a thermocouple to measure total temperature, one can determine the Mach number, static temperature, density, and velocity of the flow.
NASA Technical Reports Server (NTRS)
Clevenger, W. B., Jr.; Tabakoff, W.
1974-01-01
The particle motion in two-dimensional free and forced inward flowing vortices is considered. A particle in such a flow field experiences a balance between the aerodynamic drag forces that tend to drive erosive particles toward the axis, and centrifugal forces that prevent these particles from traveling toward the axis. Results predict that certain sizes of particles will achieve a stable orbit about the turbine axis in the inward flowing free vortex. In this condition, the radial drag force is equal to the centrifugal force. The sizes of particles that will achieve a stable orbit is shown to be related to the gas flow velocity diagram at a particular radius. A second analysis yields a description of particle sizes that will experience a centrifugal force that is greater than the radial component of the aerodynamic drag force for a more general type of particle motion.
Collisional effects on nonlinear ion drag force for small grains
Hutchinson, I. H.; Haakonsen, C. B.
2013-08-15
The ion drag force arising from plasma flow past an embedded spherical grain is calculated self-consistently and non-linearly using particle in cell codes, accounting for ion-neutral collisions. Using ion velocity distribution appropriate for ion drift driven by a force field gives wake potential and force greatly different from a shifted Maxwellian distribution, regardless of collisionality. The low-collisionality forces are shown to be consistent with estimates based upon cross-sections for scattering in a Yukawa (shielded) grain field, but only if non-linear shielding length is used. Finite collisionality initially enhances the drag force, but only by up to a factor of 2. Larger collisionality eventually reduces the drag force. In the collisional regime, the drift distribution gives larger drag than the shift distribution even at velocities where their collisionless drags are equal. Comprehensive practical analytic formulas for force that fit the calculations are provided.
Harloff, G.J.
1985-09-01
A theoretical aerodynamic model of lift and drag forces on a flat plate at angle of attack and at hypersonic speeds is presented. Real gas effects and friction drag are accounted for. Theoretical results are presented as a function of the viscous interaction parameter. The performance for two geometries is presented. 3 refs., 8 figs., 4 tabs.
Experimental Investigation of the Aerodynamic Forces on a Curveball
NASA Astrophysics Data System (ADS)
Jemmott, Colin; Utvich, Alexis; Logan, Sheldon; Rossmann, Jenn
2003-11-01
The physics of baseball has fascinated researchers nearly as long as the game has existed, yet research into aerodynamic forces on curveballs has often been conflicting and incomplete. A team of undergraduates used the newly completed Harvey Mudd College wind tunnel with a specially designed apparatus to quantify these forces. The coefficient of lift was found to be a non-linear function of both the dimensionless spin number and the Reynolds number, suggesting a stronger Reynolds number dependence than previously reported. The coefficient of drag was found to be primarily a function of spin number over the range of Reynolds numbers investigated and is significantly higher than that for a static baseball over the same Reynolds number range. While these findings help to quantify and interpret what pitchers know intuitively, they also motivate further investigations of both forces and the resulting flow field over a wider parameter range.
Study of the triple-mass Tethered Satellite System under aerodynamic drag and J2 perturbations
NASA Astrophysics Data System (ADS)
Razzaghi, Pourya; Assadian, Nima
2015-11-01
The dynamics of multi-tethered satellite formations consisting of three masses are studied in this paper. The triple-mass triple-tethered satellite system is modeled under the low Earth orbit perturbations of drag and Earth's oblateness and its equilibrium conditions are derived. It is modeled as three equal end-masses connected by a uniform-mass straight tether. The lengths of tethers are supposed to be constant and in this manner the angles of the plane consisting the masses are taken as the state variables of the system. The governing equations of motion are derived using Lagrangian approach. The aerodynamic drag perturbation is expressed as an external non-conservative force and the Earth oblateness (J2 perturbation) is considered as a term of potential energy. The equilibrium conditions of this system are found and their stability is investigated through the linear stability theory. Then, the results are verified by using a nonlinear simulation for three types of equilibrium conditions.
In vivo recording of aerodynamic force with an aerodynamic force platform: from drones to birds.
Lentink, David; Haselsteiner, Andreas F; Ingersoll, Rivers
2015-03-01
Flapping wings enable flying animals and biomimetic robots to generate elevated aerodynamic forces. Measurements that demonstrate this capability are based on experiments with tethered robots and animals, and indirect force calculations based on measured kinematics or airflow during free flight. Remarkably, there exists no method to measure these forces directly during free flight. Such in vivo recordings in freely behaving animals are essential to better understand the precise aerodynamic function of their flapping wings, in particular during the downstroke versus upstroke. Here, we demonstrate a new aerodynamic force platform (AFP) for non-intrusive aerodynamic force measurement in freely flying animals and robots. The platform encloses the animal or object that generates fluid force with a physical control surface, which mechanically integrates the net aerodynamic force that is transferred to the earth. Using a straightforward analytical solution of the Navier-Stokes equation, we verified that the method is accurate. We subsequently validated the method with a quadcopter that is suspended in the AFP and generates unsteady thrust profiles. These independent measurements confirm that the AFP is indeed accurate. We demonstrate the effectiveness of the AFP by studying aerodynamic weight support of a freely flying bird in vivo. These measurements confirm earlier findings based on kinematics and flow measurements, which suggest that the avian downstroke, not the upstroke, is primarily responsible for body weight support during take-off and landing. PMID:25589565
In vivo recording of aerodynamic force with an aerodynamic force platform: from drones to birds
Lentink, David; Haselsteiner, Andreas F.; Ingersoll, Rivers
2015-01-01
Flapping wings enable flying animals and biomimetic robots to generate elevated aerodynamic forces. Measurements that demonstrate this capability are based on experiments with tethered robots and animals, and indirect force calculations based on measured kinematics or airflow during free flight. Remarkably, there exists no method to measure these forces directly during free flight. Such in vivo recordings in freely behaving animals are essential to better understand the precise aerodynamic function of their flapping wings, in particular during the downstroke versus upstroke. Here, we demonstrate a new aerodynamic force platform (AFP) for non-intrusive aerodynamic force measurement in freely flying animals and robots. The platform encloses the animal or object that generates fluid force with a physical control surface, which mechanically integrates the net aerodynamic force that is transferred to the earth. Using a straightforward analytical solution of the Navier–Stokes equation, we verified that the method is accurate. We subsequently validated the method with a quadcopter that is suspended in the AFP and generates unsteady thrust profiles. These independent measurements confirm that the AFP is indeed accurate. We demonstrate the effectiveness of the AFP by studying aerodynamic weight support of a freely flying bird in vivo. These measurements confirm earlier findings based on kinematics and flow measurements, which suggest that the avian downstroke, not the upstroke, is primarily responsible for body weight support during take-off and landing. PMID:25589565
DOE's effort to reduce truck aerodynamic drag through joint experiments and computations.
Salari, Kambiz; Browand, Fred; Sreenivas, Kidambi; Pointer, W. David; Taylor, Lafayette; Pankajakshan, Ramesh; Whitfield, David; Plocher, Dennis; Ortega, Jason M.; Merzel, Tai; McCallen, Rose; Walker, Stephen M; Heineck, James T; Hassan, Basil; Roy, Christopher John; Storms, B.; Ross, James; Englar, Robert; Rubel, Mike; Leonard, Anthony; Radovich, Charles; Eastwood, Craig; Paschkewitz, John; Castellucci, Paul; DeChant, Lawrence Justin.
2005-08-01
Class 8 tractor-trailers are responsible for 11-12% of the total US consumption of petroleum. Overcoming aero drag represents 65% of energy expenditure at highway speeds. Most of the drag results from pressure differences and reducing highway speeds is very effective. The goal is to reduce aerodynamic drag by 25% which would translate to 12% improved fuel economy or 4,200 million gal/year. Objectives are: (1) In support of DOE's mission, provide guidance to industry in the reduction of aerodynamic drag; (2) To shorten and improve design process, establish a database of experimental, computational, and conceptual design information; (3) Demonstrate new drag-reduction techniques; and (4) Get devices on the road. Some accomplishments are: (1) Concepts developed/tested that exceeded 25% drag reduction goal; (2) Insight and guidelines for drag reduction provided to industry through computations and experiments; (3) Joined with industry in getting devices on the road and providing design concepts through virtual modeling and testing; and (4) International recognition achieved through open documentation and database.
Evaluation of Aerodynamic Drag and Torque for External Tanks in Low Earth Orbit
Stone, William C.; Witzgall, Christoph
2006-01-01
A numerical procedure is described in which the aerodynamic drag and torque in low Earth orbit are calculated for a prototype Space Shuttle external tank and its components, the “LO2” and “LH2” tanks, carrying liquid oxygen and hydrogen, respectively, for any given angle of attack. Calculations assume the hypersonic limit of free molecular flow theory. Each shell of revolution is assumed to be described by a series of parametric equations for their respective contours. It is discretized into circular cross sections perpendicular to the axis of revolution, which yield a series of ellipses when projected according to the given angle of attack. The drag profile, that is, the projection of the entire shell is approximated by the convex envelope of those ellipses. The area of the drag profile, that is, the drag area, and its center of area moment, that is, the drag center, are then calculated and permit determination of the drag vector and the eccentricity vector from the center of gravity of the shell to the drag center. The aerodynamic torque is obtained as the cross product of those vectors. The tanks are assumed to be either evacuated or pressurized with a uniform internal gas distribution: dynamic shifting of the tank center of mass due to residual propellant sloshing is not considered. PMID:27274926
Evaluation of Aerodynamic Drag and Torque for External Tanks in Low Earth Orbit.
Stone, William C; Witzgall, Christoph
2006-01-01
A numerical procedure is described in which the aerodynamic drag and torque in low Earth orbit are calculated for a prototype Space Shuttle external tank and its components, the "LO2" and "LH2" tanks, carrying liquid oxygen and hydrogen, respectively, for any given angle of attack. Calculations assume the hypersonic limit of free molecular flow theory. Each shell of revolution is assumed to be described by a series of parametric equations for their respective contours. It is discretized into circular cross sections perpendicular to the axis of revolution, which yield a series of ellipses when projected according to the given angle of attack. The drag profile, that is, the projection of the entire shell is approximated by the convex envelope of those ellipses. The area of the drag profile, that is, the drag area, and its center of area moment, that is, the drag center, are then calculated and permit determination of the drag vector and the eccentricity vector from the center of gravity of the shell to the drag center. The aerodynamic torque is obtained as the cross product of those vectors. The tanks are assumed to be either evacuated or pressurized with a uniform internal gas distribution: dynamic shifting of the tank center of mass due to residual propellant sloshing is not considered. PMID:27274926
Aerodynamic drag reduction tests on a box-shaped vehicle
NASA Technical Reports Server (NTRS)
Peterson, R. L.; Sandlin, D. R.
1981-01-01
The intent of the present experiment is to define a near optimum value of drag coefficient for a high volume type of vehicle through the use of a boattail, on a vehicle already having rounded front corners and an underbody seal, or fairing. The results of these tests will constitute a baseline for later follow-on studies to evaluate candidate methods of obtaining afterbody drag coefficients approaching the boattail values, but without resorting to such impractical afterbody extensions. The current modifications to the box-shaped vehicle consisted of a full and truncated boattail in conjunction with the faired and sealed underbody. Drag results from these configurations are compared with corresponding wind tunnel results of a 1/10 scale model. Test velocities ranged up to 96.6 km/h (60 mph) and the corresponding Reynolds numbers ranged up to 1.3 x 10 to the 7th power based on the vehicles length which includes the boattail. A simple coast-down technique was used to define drag.
Collisional Effects on Nonlinear Ion Drag Force for Small Grains
NASA Astrophysics Data System (ADS)
Hutchinson, I. H.; Haakonsen, C. B.
2013-10-01
Ion drag force arising from plasma flow past an embedded grain in a plasma is a vital part of dusty plasma dynamics. Ion-neutral collisions are often significant for experimental dusty plasmas. They are here included self-consistently in properly nonlinear comprehensive drag calculations, for the first time. The ion drag on a spherical grain is calculated using particle in cell codes SCEPTIC and COPTIC. Using ion velocity ``drift'' distribution appropriate for flow driven by a force field gives wake potential and force greatly different from a shifted Maxwellian distribution, regardless of collisionality level. The low-collisionality forces are shown to be consistent with estimates based upon cross-sections for scattering in a Yukawa (shielded) grain field, but only if nonlinear shielding length is used. Finite collisionality initially enhances the drag force, but only by up to a factor of 2. Larger collisionality eventually reduces the drag force. In the collisional regime, the drift distribution gives larger drag than the shift distribution even at velocities where their collisionless drags are equal. Comprehensive practical analytic formulas for force that fit the calculations are provided. Partially supported by NSF/DOE Grant DE-FG02-06ER54982 and Science Graduate Fellowship Program DE-AC05-06OR23100.
Estimating unsteady aerodynamic forces on a cascade in a three-dimensional turbulence field
NASA Technical Reports Server (NTRS)
Norman, T.; Johnson, W.
1985-01-01
An analytical method has been developed to estimate the unsteady aerodynamic forces caused by flow field turbulence on a wind tunnel turning vane cascade system (vane set). This method approximates dynamic lift and drag by linearly perturbing the appropriate steady state force equations, assuming that the dynamic loads are due only to free stream turbulence and that this turbulence is homogeneous, isotropic, and Gaussian. Correlation and unsteady aerodynamic effects are also incorporated into the analytical model. Using these assumptions, equations relating dynamic lift and drag to flow turbulence, mean velocity, and vane set geometry are derived. From these equations, estimates for the power spectra and rms (root mean squared value, delta) loading of both lift and drag can be determined.
FY 2004 Annual Report: DOE Project on Heavy Vehicle Aerodynamic Drag
McCallen, R C; Salari, K; Ortega, J; Castellucci, P; Eastwood, C; Whittaker, K; DeChant, L J; Roy, C J; Payne, J L; Hassan, B; Pointer, W D; Browand, F; Hammache, M; Hsu, T; Ross, J; Satran, D; Heineck, J T; Walker, S; Yaste, D; Englar, R; Leonard, A; Rubel, M; Chatelain, P
2004-11-18
The objective of this report is: (1) Provide guidance to industry in the reduction of aerodynamic drag of heavy truck vehicles; and (2) Establish a database of experimental, computational, and conceptual design information, and demonstrate potential of new drag-reduction devices. The approaches used were: (1) Develop and demonstrate the ability to simulate and analyze aerodynamic flow around heavy truck vehicles using existing and advanced computational fluid dynamics (CFD) tools; (2) Through an extensive experimental effort, generate an experimental data base for code validation; (3) Using experimental data base, validate computations; (4) Provide industry with design guidance and insight into flow phenomena from experiments and computations; and (5) Investigate aero devices (e.g., base flaps, tractor-trailer gap stabilizer, underbody skirts and wedges, blowing and acoustic devices), provide industry with conceptual designs of drag reducing devices, and demonstrate the full-scale fuel economy potential of these devices.
Direct measurements of drag forces in C. elegans crawling locomotion.
Rabets, Yegor; Backholm, Matilda; Dalnoki-Veress, Kari; Ryu, William S
2014-10-21
With a simple and versatile microcantilever-based force measurement technique, we have probed the drag forces involved in Caenorhabditis elegans locomotion. As a worm crawls on an agar surface, we found that substrate viscoelasticity introduces nonlinearities in the force-velocity relationships, yielding nonconstant drag coefficients that are not captured by original resistive force theory. A major contributing factor to these nonlinearities is the formation of a shallow groove on the agar surface. We measured both the adhesion forces that cause the worm's body to settle into the agar and the resulting dynamics of groove formation. Furthermore, we quantified the locomotive forces produced by C. elegans undulatory motions on a wet viscoelastic agar surface. We show that an extension of resistive force theory is able to use the dynamics of a nematode's body shape along with the measured drag coefficients to predict the forces generated by a crawling nematode. PMID:25418179
Aerodynamic performance of a drag reduction device on a full-scale tractor/trailer
NASA Astrophysics Data System (ADS)
Lanser, Wendy R.; Ross, James C.; Kaufman, Andrew E.
1991-09-01
The effectiveness of an aerodynamic boattail on a tractor/trailer road vehicle was measured in the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Results are examined for the tractor/trailer with and without the drag reduction device. Pressure measurements and flow visualization show that the aerodynamic boattail traps a vortex or eddy in the corner formed between the device and the rear corner of the trailer. This recirculating flow turns the flow inward as it separates from the edges of the base of the trailer. This modified flow behavior increases the pressure acting over the base area of the truck, thereby reducing the net aerodynamic drag of the vehicle. Drag measurements and pressure distributions in the region of the boattail device are presented for selected configurations. The optimum configuration reduces the overall drag of the tractor/trailer combination by about 10 percent at a zero yaw angle. Unsteady pressure measurements do not indicate strong vortex shedding, although the addition of the boattail plates increases high frequency content of the fluctuating pressure.
The drag force on an American football
NASA Astrophysics Data System (ADS)
Watts, Robert G.; Moore, Gary
2003-08-01
We have measured the drag coefficient on an American football oriented so that its major axis is pointed directly into the wind. The football was suspended from the top of a wind tunnel by bicycle spokes attached to small bearings. The results are similar to the drag coefficients reported by Rouse (1946) for the case of an ellipsoid with major diameter/minor diameter similar to the length/diameter for the football. The drag coefficient for a spinning football is slightly lower than that for a nonspinning football. Both are in the range of 0.05-0.06, about half the value assumed by Brancazio (1985), about one-third that reported by Rae and Streit (2002) and far smaller than that reported by Cunningham and Dowell (1976).
Dimples and drag: Experimental demonstration of the aerodynamics of golf balls
NASA Astrophysics Data System (ADS)
Libii, Josué Njock
2007-08-01
While it is well known that the presence of dimples reduces the drag force exerted on a golf ball, demonstrations of this phenomenon are not common. A simple pendulum is designed and used in a wind tunnel to measure the drag force exerted by a moving stream of air on a spherical object. This pendulum is then used in experiments to measure drag forces exerted on smooth balls and on golf balls in order to compare the results. Data collected from 12 balls tested at speeds ranging from 54to180km/h demonstrate that the presence of dimples on the surface of golf balls causes them to experience drag forces that are smaller than those on smooth balls of the same diameters and weights.
Measuring the force of drag on air sheared sessile drops
NASA Astrophysics Data System (ADS)
Milne, Andrew J. B.; Fleck, Brian; Amirfazli, Alidad
2012-11-01
To blow a drop along or off of a surface (i.e. to shed the drop), the drag force on the drop (based on flow conditions, drop shape, and fluid properties) must overcome the adhesion force between the drop and the surface (based on surface tension, drop shape, and contact angle). While the shedding of sessile drops by shear flow has been studied [Milne, A. J. B. & Amirfazli, A. Langmuir 25, 14155 (2009).], no independent measurements of the drag or adhesion forces have been made. Likewise, analytic predictions are limited to hemispherical drops and low air velocities. We present, therefore, measurements of the drag force on sessile drops at air velocities up to the point of incipient motion. Measurements were made using a modified floating element shear sensor in a laminar low speed wind tunnel to record drag force over the surface with the drop absent, and over the combined system of the surface and drop partially immersed in the boundary layer. Surfaces of different wettabilities were used to study the effects of drop shape and contact angles, with drop volume ranged between approximately 10 and 100 microlitres. The drag force for incipient motion (which by definition equals the maximum of the adhesion force) is compared to simplified models for drop adhesion such as that of Furmidge
McCallen, R; Salari, K; Ortega, J; Castellucci, P; Eastwood, C; DeChant, L; Hassan, B; Browand, F; Arcas, D; Ross, J; Heineck, J; Storms, B; Walker, S; Leonard, A; Roy, C; Whitfield, D; Pointer, D; Sofu, T; Englar, R; Funk, R
2004-08-17
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held in Portland, Oregon on July 1, 2004. The purpose of the meeting was to provide a summary of achievements, discuss pressing issues, present a general overview of future plans, and to provide a forum for dialogue with the Department of Energy (DOE) and industry representatives. The meeting was held in Portland, because the DOE Aero Team participated in an exclusive session on Heavy Truck Vehicle Aerodynamic Drag at the 34th AIAA Fluid Dynamics Conference and Exhibit in Portland on the morning of July 1st, just preceding our Working Group meeting. Even though the paper session was on the last day of the Conference, the Team presented to a full room of interested attendees.
Drag force and jet propulsion investigation of a swimming squid
NASA Astrophysics Data System (ADS)
Tabatabaei, Mahdi; Bahadır Olcay, Ali; Gokçen, Gökhan; Heperkan, Hasan A.
2015-05-01
In this study, CAD model of a squid was obtained by taking computer tomography images of a real squid. The model later placed into a computational domain to calculate drag force and performance of jet propulsion. The drag study was performed on the CAD model so that drag force subjected to real squid was revealed at squid's different swimming speeds and comparison has been made with other underwater creatures (e.g., a dolphin, sea lion and penguin). The drag coefficient (referenced to total wetted surface area) of squid is 0.0042 at Reynolds number 1.6x106 that is a %4.5 difference from Gentoo penguin. Besides, jet flow of squid was simulated to observe the flow region generated in the 2D domain utilizing dynamic mesh method to mimic the movement of squid's mantle cavity.
Effect of guideway discontinuities on magnetic levitation and drag forces
Rossing, T.D.; Korte, R.; Hull, J.R. )
1991-11-15
Transients in the lift and drag forces on a NdFeB permanent magnet were observed as the magnet passed over various discontinuities in a rotating aluminum disk at velocities of 4 to 25 m/s. For full cuts in the disk, the amplitude of the lift and drag transients and the wave form of the drag transient depend on the width, and the amplitudes are much larger than for partial cuts. The use of a backing plate to join two cut segments is ineffective.
The roles of aerodynamic and inertial forces on maneuverability in flapping flight
NASA Astrophysics Data System (ADS)
Vejdani, Hamid; Boerma, David; Swartz, Sharon; Breuer, Kenneth
2015-11-01
We investigate the relative contributions of aerodynamic and the whole-body dynamics in generating extreme maneuvers. We developed a 3D dynamical model of a body (trunk) and two rectangular wings using a Lagrangian formulation. The trunk has 6 degrees of freedom and each wing has 4 degrees of actuation (flapping, sweeping, wing pronation/supination and wing extension/flexion) and can be massless (like insect wings) or relatively massive (like bats). To estimate aerodynamic forces, we use a blade element method; drag and lift are calculated using a quasi-steady model. We validated our model using several benchmark tests, including gliding and hovering motion. To understand the roles of aerodynamic and inertial forces, we start the investigation by constraining the wing motion to flapping and wing length extension/flexion motion. This decouples the trunk degrees of freedom and affects only roll motion. For bats' dynamics (massive wings), the model is much more maneuverable than the insect dynamics case, and the effect of inertial forces dominates the behavior of the system. The role of the aerodynamic forces increases when the wings have sweeping and flapping motion, which affects the pitching motion of the body. We also analyzed the effect of all wing motions together on the behavior of the model in the presence and in the absence of aerodynamic forces.
Force measurements in aerodynamics using piezoelectric multicomponent force transducers
NASA Astrophysics Data System (ADS)
Schewe, G.
The present paper is concerned with a device for the measurement of steady and unsteady aerodynamic forces in a wind tunnel test. The paper represents a continuation of an article written by Schewe (1982) about a multicomponent balance consisting of piezoelectric force transducers for a high-pressure wind tunnel. Advantages of the piezoelectric force-measuring technique compared to other techniques are related to the high rigidity of the quartz crystal sensor elements, taking into account low interference (cross talk) for multicomponent measurements, high natural frequency, and broad dynamic range. It is pointed out that the limitations with respect to quasi-static measurements imposed by the drift of the zero point are not as extensive as generally believed, while drift correction methods improve the measurement accuracy.
The use of velodrome tests to evaluate aerodynamic drag in professional cyclists.
García-López, J; Ogueta-Alday, A; Larrazabal, J; Rodríguez-Marroyo, J A
2014-05-01
The purpose of this study was to analyse the validity, reliability and sensitivity of velodrome tests to detect small changes in aerodynamic drag in cycling. 12 professional cyclists were assessed to obtain the drag area (SCx) during wind tunnel and velodrome tests. Incremental and steady-state protocols were performed in the velodrome with a portable power meter, and 6 bicycle positions were analysed and compared that involved lowering the handlebars and advancing the pads between 2-5 cm. A significant relationship (r=0.88, p<0.001) between the SCx in the wind tunnel and velodrome tests was found (0.240 ± 0.007 and 0.237 ± 0.008 m2, respectively). The velodrome tests underestimated the SCx (0.0035 ± 0.0038 m2 and p<0.01), which decreased (p<0.001) when the bicycle speed increased (0.0013 m2 each 1 km · h(-1)). The SCx values showed high reliability during the steady-state (r=0.99, p<0.001) and incremental protocols (r=0.94, p<0.001). Small changes in the aerodynamic position affected the SCx (p<0.001), which decreased by 0.011 ± 0.007 m2 (4.6 ± 2.9%, 95% CI=2.7-6.4%). In conclusion, the validity, reliability and sensitivity of velodrome tests to detect small changes in aerodynamic drag in cycling were demonstrated. Although SCx values were not interchangeable between different studies, the velodrome tests presented advantages with respect to the wind tunnel tests. PMID:24081618
Progress in reducing aerodynamic drag for higher efficiency of heavy duty trucks (class 7-8)
Brady, M; Browand, F; Hammache, M; Heineck, J T; Leonard, A; McCallen, R; Ross, J; Rutledge, W; Salari, K; Storms, B
1999-04-01
This paper describes research and development for reducing the aerodynamic drag of heavy vehicles by demonstrating new approaches for the numerical simulation and analysis of aerodynamic flow. In addition, greater use of newly developed computational tools holds promise for reducing the number of prototype tests, for cutting manufacturing costs, and for reducing overall time to market. Experimental verification and validation of new computational fluid dynamics methods are also an important part of this approach. Experiments on a model of an integrated tractor-trailer are underway at NASA Ames Research Center and the University of Southern California. Companion computer simulations are being performed by Sandia National Laboratories, Lawrence Livermore National Laboratory, and California Institute of Technology using state-of-the-art techniques, with the intention of implementing more complex methods in the future.
Progress in Reducing Aerodynamic Drag for Higher Efficiency of Heavy Duty Trucks (Class 7-8)
Rose McCallen; Richard Couch; Juliana Hsu; Fred Browand; Mustapha Hammache; Anthony Leonard; Mark Brady; Kambiz Salari; Walter Rutledge; James Ross; Bruce Storms; J.T. Heineck; David Driver; James Bell; Gregory Zilliac
1999-12-31
This paper describes research and development for reducing the aerodynamic drag of heavy vehicles by demonstrating new approaches for the numerical simulation and analysis of aerodynamic flow. In addition, greater use of newly developed computational tools holds promise for reducing the number of prototype tests, for cutting manufacturing costs, and for reducing overall time to market. Experimental verification and validation of new computational fluid dynamics methods are also an important part of this approach. Experiments on a model of an integrated tractor-trailer are underway at NASA Ames Research Center and the University of Southern California. Companion computer simulations are being performed by Sandia National Laboratories, Lawrence Livermore National Laboratory, and California Institute of Technology using state-of-the-art techniques, with the intention of implementing more complex methods in the future.
Systematic approach to analyzing and reducing aerodynamic drag of heavy vehicles
McCallen, R.; Browand, F.; Leonard, A.; Rutledge, W.
1997-09-16
This paper presents an approach for reducing aerodynamic drag of heavy vehicles by systematically analyzing trailer components using existing computational tools and moving on to the analyses of integrated tractor-trailers using advanced computational tools. Experimental verification and validation are also an important part of this approach. The project is currently in the development phase while we are in the process of constructing a Multi-Year Program Plan. Projects I and 2 as described in this paper are the anticipated project direction. Also included are results from past and current related activities by the project participants which demonstrate the analysis approach.
Mechanosensing using drag force for imaging soft biological membranes
Zarnitsyn, Vladimir G.; Fedorov, Andrei G.
2008-01-01
We investigate physical processes taking place during nanoscale mechanosensing of soft biological membranes in liquid environment. The examples include tapping mode imaging by atomic force microscope (AFM) and microscopy based on Brownian motion of a nanoparticle in an optical-tweezers-controlled trap. The softness and fluidity of the cellular membrane make it difficult to accurately detect (i.e., image) the shape of the cell using traditional mechanosensing methods. The aim of the reported work is to theoretically evaluate if the drag force acting on the nanoscale mechanical probe due to combined effect of intra- and extra- cellular environments can be exploited to develop a new imaging mode suitable for soft cellular interfaces. We approach this problem by rigorous modeling of the fluid mechanics of a complex viscoelastic biosystem in which the probe sensing process is intimately coupled to the membrane biomechanics. The effects of the probe dimensions, elastic properties of the membrane, as well as intra- and extra- cellular viscosities are investigated in detail to establish the structure and evolution of the fluid field as well as dynamics of membrane deformation. The results of numerical simulations, supported by the predictions of the scaling analysis of forces acting on the probe, suggest that the viscous drag is the dominant force dictating probe dynamics as it approaches a biological interface. The increase in the drag force is shown to be measurable, to scale linearly with an increase in the viscosity ratio of the fluids on either sides of the membrane, and to be inversely proportional to probe-to-membrane distance. This leads to postulation of a new strategy for lipid membrane imaging by AFM or other mechanosensing methods using variation in the maximum drag force as an indicator of the membrane position. PMID:17439250
Inlet Aerodynamics and Ram Drag of Laser-Propelled Lightcraft Vehicles
NASA Astrophysics Data System (ADS)
Langener, Tobias; Myrabo, Leik; Rusak, Zvi
2010-05-01
Numerical simulations are used to study the aerodynamic inlet properties of three axisymmetric configurations of laser-propelled Lightcraft vehicles operating at subsonic, transonic and supersonic speeds up to Mach 5. The 60 cm vehicles were sized for launching 0.1-1.0 kg nanosatellites with combined-cycle airbreathing/rocket engines, transitioning between propulsion modes at roughly Mach 5-6. Results provide the pressure, temperature, density, and velocity flowfields around and through the three representative vehicle/engine configurations, as well as giving the resulting ram drag and total drag coefficients—all as a function of flight Mach number. Simulations with rotating boundaries were also carried out, since for stability reasons, Lightcraft are normally spun up before lift-off. Given the three alternatives, it is demonstrated that the optimal geometry for minimum drag is the configuration with a parabola nose; hence, these inlet flow conditions are being applied in subsequent "direct connect" 2D laser propulsion experiments in a small transonic flow facility.
A drag-based mechanism for vertical force production in the smallest flying insects
NASA Astrophysics Data System (ADS)
Jones, Shannon; Laurenza, Ryan; Miller, Laura
2013-11-01
Previous work has shown that the flight kinematics and aerodynamics of the smallest flying insects may be significantly different than that of their larger counterparts. These small insects, such as thrips and parasitoid wasps, are on the order of 1 mm in length and operate at a Reynolds number less than 10. Due to their small size and high wing beat frequency, quantitative data on the wing kinematics of the smallest insects is not available. As a result, there has been much debate and speculation about the flight strategies employed by these insects. With the challenges associated with generating lift at low Reynolds numbers, it could be beneficial for the smallest insects to use a drag-based motion to generate some or all of its vertical force, however this has not been rigorously investigated. We used computational fluid dynamics to investigate the feasibility of drag-based propulsion in the tiniest insects. We investigated the vertical force generated by an idealized drag-based vertical stroke over a range of Reynolds numbers from 1 to 150. We also compared this stroke to more conventional hovering stroke kinematics such as that of a fruit fly and dragonfly.
Browand, F; Gutierrez, W; Leonard, A; McBride, D; McCallen, R; Ross, J; Roth, K; Rutledge, W; Salari, K
1998-09-28
The first Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Sandia National Laboratories (SNL) in Albuquerque, New Mexico on August 28, 1998. The purpose of the meeting was to review the proposed Multi-Year Program Plan (MYPP) and provide an update on the Group"s progress. In addition, the technical details of each organization"s activities were presented and discussed. Presentations were given by representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT), Lawrence Livermore National Laboratory (LLNL), SNL, University of Southern California (USC), California Institute of Technology (Caltech), and NASA Ames Research Center. These presenters are part of a DOE appointed Technical Team assigned to developing the MYPP. The goal of the MYPP is to develop and demonstrate the ability to simulate and analyze aerodynamic flow around heavy truck vehicles using existing and advanced computational tools (A Multi-Year Program Plan for the Aerodynamic Design of Heavy Vehicles, R. McCallen, D. McBride, W. Rutledge, F. Browand, A. Leonard, .I. Ross, UCRL-PROP- 127753 Dr. Rev 2, May 1998). This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions from the Meeting participants, and outlines the future action items.
Collisionless ion drag force on a spherical grain
NASA Astrophysics Data System (ADS)
Hutchinson, I. H.
2006-02-01
The ion drag force on a spherical grain situated in a flowing collisionless plasma is obtained from the specialized coordinate electrostatic particle and thermals in cell simulation code (SCEPTIC) (Hutchinson 2002 Plasma Phys. Control. Fusion 44 1953, Hutchinson 2003 Plasma Phys. Control. Fusion 45 1477, Hutchinson 2005 Plasma Phys. Control. Fusion 47 71) and compared with recent analytic approximate treatments in the interesting and relevant case when the Debye length is only moderately larger than the sphere radius. There is a substantial complex structure in the results for transonic flows, which is explained in terms of the details of ion orbits. Naturally the prior analytic approximations miss this structure, and as a result they seriously underestimate the drag for speeds near the sound speed. An easy-to-evaluate expression for force is provided that fits the comprehensive results of the code. This expression, with minor modification, also fits the results even for Debye length much smaller than the sphere radius.
Aerodynamic drag reduction apparatus for gap-divided bluff bodies such as tractor-trailers
Ortega, Jason M.; Salari, Kambiz
2006-07-11
An apparatus for reducing the aerodynamic drag of a bluff-bodied vehicle such as a tractor-trailer in a flowstream, the bluff-bodied vehicle of a type having a leading portion, a trailing portion connected to the leading portion, and a gap between the leading and trailing portions defining a recirculation zone. The apparatus is preferably a baffle assembly, such as a vertical panel, adapted to span a width of the gap between the leading and trailing portions so as to impede cross-flow through the gap, with the span of the baffle assembly automatically adjusting for variations in the gap width when the leading and trailing portions pivot relative to each other.
Computation of ion drag force on a static spherical dust grain immersed in rf discharges
Ikkurthi, V. R.; Melzer, A.; Matyash, K.; Schneider, R.
2009-04-15
The ion drag force on static spherical dust grains located in an argon rf discharge under typical laboratory experiment conditions has been computed using a three-dimensional particle-particle-particle-mesh code. Elastic and inelastic collisions have been included in the current model to obtain realistic rf discharge plasma conditions. The ion drag has been computed for various sizes of dust placed at different locations in the rf discharge under different gas pressures. The orbital drag force is typically found larger than the collection drag force. Ion-neutral collisions increase flux to the dust and hence the total drag force for collisional case is found larger than the collisionless case. Within the pressure range investigated, the drag forces do not vary much with pressure. The size dependence of the drag force is nonlinear and agrees well with the forces computed from the analytical models.
On negative ion-drag force for dust in collisional plasmas
Patacchini, Leonardo; Hutchinson, Ian H.
2008-09-07
The ion-drag force on a dust particle in collisional plasmas is self-consistently calculated using the Particle In Cell code SCEPTIC in the entire range of charge-exchange collisionlality. It is shown that the ion-drag only reverses in the strongly collisional regime, where other forces are of much stronger magnitude than the ion-drag itself.
On negative ion-drag force for dust in collisional plasmas
NASA Astrophysics Data System (ADS)
Patacchini, Leonardo; Hutchinson, Ian H.
2008-09-01
The ion-drag force on a dust particle in collisional plasmas is self-consistently calculated using the Particle In Cell code SCEPTIC in the entire range of charge-exchange collisionlality. It is shown that the ion-drag only reverses in the strongly collisional regime, where other forces are of much stronger magnitude than the ion-drag itself.
Characterization of speed fluctuation and drag force in young swimmers: a gender comparison.
Barbosa, Tiago M; Costa, Mário J; Morais, Jorge E; Morouço, Pedro; Moreira, Marc; Garrido, Nuno D; Marinho, Daniel A; Silva, António J
2013-12-01
The aim of this study was to compare the speed fluctuation and the drag force in young swimmers between genders. Twenty-three young pubertal swimmers (12 boys and 11 girls) volunteered as subjects. Speed fluctuation was measured using a kinematical mechanical method (i.e., speedo-meter) during a maximal 25-m front crawl bout. Active drag, active drag coefficient and power needed to overcome drag were measured with the velocity perturbation method for another two maximal 25m front crawl bouts with and without the perturbation device. Passive drag and the passive drag coefficient were estimated using the gliding decay velocity method after a maximal push-off from the wall while being fully immersed. The technique drag index was also assessed as a ratio between active and passive drag. Boys presented meaningfully higher speed fluctuation, active drag, power needed to overcome drag and technique drag index than the girls. There were no significant gender differences for active drag coefficient, passive drag and passive drag coefficient. There were positive and moderate-strong associations between active drag and speed fluctuation when controlling the effects of swim velocity. So, increasing speed fluctuation leads to higher drag force values and those are even higher for boys than for girls. PMID:24071552
McCallen, R C
2005-08-17
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory, Livermore, California on May 12th and 13th of 2005. The purpose of the first day's meeting, May 12th, was to provide a summary of achievements, discuss issues, present a general overview of future plans, and to offer a forum for dialogue with the Department of Energy (DOE) and representatives from industry, universities, and research and development organizations performing work related to heavy vehicle aerodynamics. This first meeting day was open to participants from industry and research organizations from both the US and Canada. The second day, May 13th, was attended only by representatives from the 9 organizations that form the DOE Consortium effort and their government sponsors. The purpose of the second day's meeting was to further discuss fiscal year 2005's activities, any further specific pressing issues, identify individual action items, and provide an overview of plans for fiscal year 2006. Based on discussions at the Meeting, the existing project goals remain unchanged and enhancing interactions with fleet owners and operators was emphasized: (1) Perform heavy vehicle computations and experiments, (2) Validate computations using experimental data, (3) Provide design guidance and insight into flow phenomena from experiments and computations, and (4) Investigate aero devices with emphasis on collaborative efforts with fleet owners and operators.
NASA Astrophysics Data System (ADS)
Mostaza Prieto, David; Graziano, Benjamin P.; Roberts, Peter C. E.
2014-01-01
This paper reviews currently available methods to calculate drag coefficients of spacecraft traveling in low Earth orbits (LEO). Aerodynamic analysis of satellites is necessary to predict the drag force perturbation to their orbital trajectory, which for LEO orbits is the second in magnitude after the gravitational disturbance due to the Earth's oblateness. Historically, accurate determination of the spacecraft drag coefficient (CD) was rarely required. This fact was justified by the low fidelity of upper atmospheric models together with the lack of experimental validation of the theory. Therefore, the calculation effort was a priori not justified. However, advances on the field, such as new atmospheric models of improved precision, have allowed for a better characterization of the drag force. They have also addressed the importance of using physically consistent drag coefficients when performing aerodynamic calculations to improve analysis and validate theories. We review the most common approaches to predict these coefficients.
Drag and propulsive forces in electric sails with negative polarity
NASA Astrophysics Data System (ADS)
Sanchez-Torres, Antonio
2016-02-01
An electric solar sail (E-sail) is a recent propellantless propulsion concept for a direct exploration of the Solar System. An E-sail consists of a set of bare, conductive tethers at high positive/negative bias, prone to extract solar wind momentum by Coulomb deflection of protons. Additionally, a negatively biased E-sail has been proposed as a concept for de-orbiting space debris with drag forces produced in Low Earth Orbit (LEO). The present work focuses on the negative-bias case with a sheath that must be correctly modeled for a flowing plasma ambient. Ion scattering within the sheath and the resulting force are determined for several plasma conditions. Since the plasma flow does reduce the effective range for the ion scattering within the sheath, the resulting force is then reduced. Tethers at very high negative bias should be required for extremely high plasma flow.
Dynamic behavior of a beam drag-force anemometer
NASA Technical Reports Server (NTRS)
Fralick, G. C.
1980-01-01
A cantilevered beam with strain gages attached to the fixed ends and the minimax technique were used in an experiment conducted to determine the dynamic behavior of a drag-force anemometer in high frequency, unsteady flow. In steady flow the output of the anemometer is proportional to stream velocity head and flow angle. Fluid mechanics suggests that, in unsteady flow, the output would also be proportional to the rate of change of fluid velocity. It was determined that effects due to the rate of change of fluid velocity are negligible for the probe geometry and frequencies involved.
Device measures fluid drag on test vehicles
NASA Technical Reports Server (NTRS)
Freeman, R.; Judd, J. H.; Leiss, A.
1965-01-01
Electromechanical drag balance device measures the aerodynamic drag force acting on a vehicle as it moves through the atmosphere and telemeters the data to a remote receiving station. This device is also used for testing the hydrodynamic drag characteristics of underwater vehicles.
NASA Astrophysics Data System (ADS)
澤田, 秀夫
The aerodynamic performance of an AGARD-B model, as an example of a winged model, was measured in a low-speed wind tunnel equipped with the JAXA 60cm Magnetic Suspension and Balance System (MSBS). The flow speed was in the range between 25m/s and 35m/s, and the angle of attack and the yaw angle were in the range of [- 8, 4] and [- 3, 3] degrees, respectively. Six components of the aerodynamic force were evaluated by using the control coil currents of the MSBS. In evaluating the drag, the effect of the lift on the drag must be evaluated at MSBS when the lift is much larger than drag. A new evaluation method for drag and lift was proposed and was examined successfully by subjecting the model to the same loads as in the wind tunnel test. The drag coefficient at zero lift and the derivatives of the lift and pitching moment coefficient with respect to the angle of attack were evaluated and compared with other source data sets. The obtained data agreed well with the corresponding values of the other sources. The side force, yawing moment and rolling moment coefficients were also evaluated on the basis of corresponding calibration test results, and reasonable results were obtained, although they could not be compared due to the lack of reliable data sets.
Fluidic Control of Aerodynamic Forces on an Axisymmetric Body
NASA Astrophysics Data System (ADS)
Abramson, Philip; Vukasinovic, Bojan; Glezer, Ari
2007-11-01
The aerodynamic forces and moments on a wind tunnel model of an axisymmetric bluff body are modified by induced local vectoring of the separated base flow. Control is effected by an array of four integrated aft-facing synthetic jets that emanate from narrow, azimuthally-segmented slots, equally distributed around the perimeter of the circular tail end within a small backward facing step that extends into a Coanda surface. The model is suspended in the wind tunnel by eight thin wires for minimal support interference with the wake. Fluidic actuation results in a localized, segmented vectoring of the separated base flow along the rear Coanda surface and induces asymmetric aerodynamic forces and moments to effect maneuvering during flight. The aerodynamic effects associated with quasi-steady and transitory differential, asymmetric activation of the Coanda effect are characterized using direct force and PIV measurements.
Bernoulli's Law and Aerodynamic Lifting Force.
ERIC Educational Resources Information Center
Weltner, Klaus
1990-01-01
Explains the lifting force based on Bernoulli's law and as a reaction force. Discusses the interrelation of both explanations. Considers accelerations in line with stream lines and perpendicular to stream lines. (YP)
Liu, Changran; Li, Zhigang; Wang, Hai
2016-08-01
Analytical expressions are derived for aerodynamic drag force on small cylinders in the free molecule flow using the gas-kinetic theory. The derivation considers the effect of intermolecular interactions between the cylinder and gas media. Two limiting collision models, specular and diffuse scattering, are investigated in two limiting cylinder orientations with respect to the drift velocity. The earlier solution of Dahneke [B. E. Dahneke, J. Aerosol Sci. 4, 147 (1973)10.1016/0021-8502(73)90066-9] is shown to be a special case of the current expressions in the rigid-body limit of collision. Drag force expressions are obtained for cylinders that undergo Brownian rotation and for those that align with the drift velocity. The validity of the theoretical expressions is tested against experimental mobility data available for carbon nanotubes. PMID:27627388
NASA Astrophysics Data System (ADS)
Liu, Changran; Li, Zhigang; Wang, Hai
2016-08-01
Analytical expressions are derived for aerodynamic drag force on small cylinders in the free molecule flow using the gas-kinetic theory. The derivation considers the effect of intermolecular interactions between the cylinder and gas media. Two limiting collision models, specular and diffuse scattering, are investigated in two limiting cylinder orientations with respect to the drift velocity. The earlier solution of Dahneke [B. E. Dahneke, J. Aerosol Sci. 4, 147 (1973), 10.1016/0021-8502(73)90066-9] is shown to be a special case of the current expressions in the rigid-body limit of collision. Drag force expressions are obtained for cylinders that undergo Brownian rotation and for those that align with the drift velocity. The validity of the theoretical expressions is tested against experimental mobility data available for carbon nanotubes.
Aeroacoustics. [analysis of properties of sound generated by aerodynamic forces
NASA Technical Reports Server (NTRS)
Goldstein, M., E.
1974-01-01
An analysis was conducted to determine the properties of sound generated by aerodynamic forces or motions originating in a flow, such as the unsteady aerodynamic forces on propellers or by turbulent flows around an aircraft. The acoustics of moving media are reviewed and mathematical models are developed. Lighthill's acoustic analogy and the application to turbulent flows are analyzed. The effects of solid boundaries are calculated. Theories based on the solution of linearized vorticity and acoustic field equations are explained. The effects of nonuniform mean flow on the generation of sound are reported.
Aerodynamics of Dragonfly in Hover: Force measurements and PIV results
NASA Astrophysics Data System (ADS)
Deng, Xinyan; Hu, Zheng
2009-11-01
We useda pair of dynamically scaled robotic dragonfly model wings to investigate the aerodynamic effects of wing-wing interaction in dragonflies. We follow the wing kinematics of real dragonflies in hover, while systematically varied the phase difference between the forewing and hindwing. Instantaneous aerodynamic forces and torques were measured on both wings, while flow visualization and PIV results were obtained. The results show that, in hovering flight, wing-wing interaction causes force reduction for both wings at most of the phase angle differences except around 0 degree (when the wings are beating in-phase).
The BMW analytic aerodynamic drag method for the Vinti satellite theory
NASA Technical Reports Server (NTRS)
Watson, J. S.; Mistretta, G. D.; Bonavito, N. L.
1972-01-01
In order to retain separability in the Vinti theory of earth satellite motion when a non conservative force such as air drag is considered, a set of variational equations for the orbital elements are introduced, and expressed as functions of the transverse, radial, and normal components of the nonconservative forces acting on the system. In particular, the atmospheric density profile is written as a fitted exponential function of the eccentric anomaly, which reproduces tabular values of static model atmospheric densities at all altitudes to within ninety-eight percent and simultaneously reduces the variational equations to indefinite integrals with closed form evaluations, whose limits are in terms of the eccentric anomaly. The values of the limits for any arbitrary time interval are obtained from the Vinti program. Results of the BMW (Bonavito, Mistretta, Watson) theory for the case of the intense air drag satellites San Marco-2 and Air Force Cannonball are given. These results indicate that the satellite ephemerides produced by the BMW theory in conjunction with the Vinti program are of very high accuracy. In addition, since the program is entirely analytic, several months of ephemerides can be obtained within a few seconds of computer time.
Dividers for reduction of aerodynamic drag of vehicles with open cavities
NASA Technical Reports Server (NTRS)
Storms, Bruce L. (Inventor)
2007-01-01
A drag-reduction concept for vehicles with open cavities includes dividing a cavity into smaller adjacent cavities through installation of one or more vertical dividers. The dividers may extend the full depth of the cavity or only partial depth. In either application, the top of the dividers are typically flush with the top of the bed or cargo bay of the vehicle. The dividers may be of any material, but are strong enough for both wind loads and forces encountered during cargo loading/unloading. For partial depth dividers, a structural angle may be desired to increase strength.
Nonuniform charging effects on ion drag force in drifting dusty plasmas
Chang, Dong-Man; Chang, Won-Seok; Jung, Young-Dae
2006-03-01
The nonuniform polarization charging effects on the ion drag force are investigated in drifting dusty plasmas. The ion drag force due to the ion-dust grain interaction is obtained as a function of the dust charge, ion charge, plasma temperature, Mach number, Debye length, and collision energy. The result shows that the nonuniform charging effects enhance the momentum transfer cross section as well as the ion drag force. It is found that the momentum transfer cross section and the ion drag force including nonuniform polarization charging effects increase with increasing the Mach number and also the ion drag force increases with increasing the temperature. In addition, it is found that the ion drag force is slightly decreasing with an increase of the Debye length.
Aerodynamic tower shake force analysis for VAWT
Loth, J.L.
1985-02-01
Vertical axis wind turbines (VAWT) are subjected to blade lift forces which vary continuously in both magnitude and direction. These blade lift forces are transmitted via the blade support arms to the tower. The resulting tower force vector is a composite of: a downwind and a crosswind average force component, rotating force vectors, and force vectors oscillating in the crosswind direction. The frequency of the rotating and oscillating forces are multiples of the product of Bw, where B is the number of blades used and ..omega.. is the rotor angular velocity. The magnitude of the largest tower shake force vector is of the same order as the average downwind force component, and may represent a serious design constraint in the calculation of the required tower stiffness. A closed-form solution for the tower force vectors has been derived, by introducing a suitable wind interference model. It shows that the magnitude of the largest tower shake force vector, using a threebladed rotor, is four times smaller than a two-bladed rotor. The Betz limit and the optimum tip speed ratio as a function of solidity has been derived by comparison with two semicylindrical actuators in series.
Variability in Measurement of Swimming Forces: A Meta-Analysis of Passive and Active Drag
ERIC Educational Resources Information Center
Havriluk, Rod
2007-01-01
An analysis was conducted to identify sources of true and error variance in measuring swimming drag force to draw valid conclusions about performance factor effects. Passive drag studies were grouped according to methodological differences: tow line in pool, tow line in flume, and carriage in tow tank. Active drag studies were grouped according to…
The drag force on a subsonic projectile in a fluid complex plasma
Ivlev, A. V.; Zhukhovitskii, D. I.
2012-09-15
The incompressible Navier-Stokes equation is employed to describe a subsonic particle flow induced in complex plasmas by a moving projectile. Drag forces acting on the projectile in different flow regimes are calculated. It is shown that, along with the regular neutral gas drag, there is an additional force exerted on the projectile due to dissipation in the surrounding particle fluid. This additional force provides significant contribution to the total drag.
Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond
2007-04-30
Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their effect on
The effect of plasma actuator on the depreciation of the aerodynamic drag on box model
NASA Astrophysics Data System (ADS)
Harinaldi, Budiarso, Julian, James; Rabbani M., N.
2016-06-01
Recent active control research advances have provided many benefits some of which in the field of transportation by land, sea as well as by air. Flow engineering by using active control has proven advantages in energy saving significantly. One of the active control equipment that is being developed, especially in the 21st century, is a plasma actuator, with the ability to modify the flow of fluid by the approach of ion particles makes these actuators a very powerful and promising tool. This actuator can be said to be better to the previously active control such as suction, blowing and synthetic jets because it is easier to control, more flexible because it has no moving parts, easy to be manufactured and installed, and consumes a small amount of energy with maximum capability. Plasma actuator itself is the composition of a material composed of copper and a dielectric sheet, where the copper sheets act as an electricity conductor and the dielectric sheet as electricity insulator. Products from the plasma actuators are ion wind which is the result of the suction of free air around the actuator to the plasma zone. This study investigates the ability of plasma actuators in lowering aerodynamic drag which is commonly formed in the models of vehicles by varying the shape of geometry models and the flow speed.
Aerodynamic forces and flow fields of a two-dimensional hovering wing
NASA Astrophysics Data System (ADS)
Lua, K. B.; Lim, T. T.; Yeo, K. S.
2008-12-01
This paper reports the results of an experimental investigation on a two-dimensional (2-D) wing undergoing symmetric simple harmonic flapping motion. The purpose of this investigation is to study how flapping frequency (or Reynolds number) and angular amplitude affect aerodynamic force generation and the associated flow field during flapping for Reynolds number ( Re) ranging from 663 to 2652, and angular amplitudes ( α A) of 30°, 45° and 60°. Our results support the findings of earlier studies that fluid inertia and leading edge vortices play dominant roles in the generation of aerodynamic forces. More importantly, time-resolved force coefficients during flapping are found to be more sensitive to changes in α A than in Re. In fact, a subtle change in α A may lead to considerable changes in the lift and drag coefficients, and there appears to be an optimal mean lift coefficient left( {overline {C_{{text{l}}} } } right) around α A = 45°, at least for the range of flow parameters considered here. This optimal condition coincides with the development a reverse Karman Vortex street in the wake, which has a higher jet stream than a vortex dipole at α A = 30° and a neutral wake structure at α A = 60°. Although Re has less effect on temporal force coefficients and the associated wake structures, increasing Re tends to equalize mean lift coefficients (and also mean drag coefficients) during downstroke and upstroke, thus suggesting an increasing symmetry in the mean force generation between these strokes. Although the current study deals with a 2-D hovering motion only, the unique force characteristics observed here, particularly their strong dependence on α A, may also occur in a three-dimensional hovering motion, and flying insects may well have taken advantage of these characteristics to help them to stay aloft and maneuver.
NASA Astrophysics Data System (ADS)
Shi, Tong; Wang, Yikang; Wan, Linfeng; Cheng, Xin; Ding, Mingde; Zhang, Jie
2015-06-01
Accurately predicting the arrival of coronal mass ejections (CMEs) to the Earth based on remote images is of critical significance for the study of space weather. In this paper, we make a statistical study of 21 Earth-directed CMEs, specifically exploring the relationship between CME initial speeds and transit times. The initial speed of a CME is obtained by fitting the CME with the Graduated Cylindrical Shell model and is thus free of projection effects. We then use the drag force model to fit results of the transit time versus the initial speed. By adopting different drag regimes, i.e., the viscous, aerodynamics, and hybrid regimes, we get similar results, with a least mean estimation error of the hybrid model of 12.9 hr. CMEs with a propagation angle (the angle between the propagation direction and the Sun–Earth line) larger than their half-angular widths arrive at the Earth with an angular deviation caused by factors other than the radial solar wind drag. The drag force model cannot be reliably applied to such events. If we exclude these events in the sample, the prediction accuracy can be improved, i.e., the estimation error reduces to 6.8 hr. This work suggests that it is viable to predict the arrival time of CMEs to the Earth based on the initial parameters with fairly good accuracy. Thus, it provides a method of forecasting space weather 1–5 days following the occurrence of CMEs.
NASA Technical Reports Server (NTRS)
Parker, E. N.
1979-01-01
Analysis of the dynamical stability of a large flux tube suggests that the field of a sunspot must divide into many separate tubes within the first 1000 km below the surface. Buoyancy of the Wilson depression at the visible surface and probably also a downdraft beneath the sunspot hold the separate tubes in a loose cluster. Convective generation of Alfven waves, which are emitted preferentially downward, cools the tubes. Aerodynamic drag on a slender flux tube stretched vertically across a convective cell is also studied. Since the drag is approximately proportional to the local kinetic energy density, the density stratification weights the drag in favor of the upper layers. Horizontal motions concentrated in the bottom of the convective cell may reverse this density effect. A downdraft of about two km/sec through the flux tubes beneath the sunspot is hypothesized.
Méndez-Méndez, J V; Alonso-Rasgado, M T; Faria, E Correia; Flores-Johnson, E A; Snook, R D
2014-11-01
When atomic force microscopy (AFM) is employed for in vivo study of immersed biological samples, the fluid medium presents additional complexities, not least of which is the hydrodynamic drag force due to viscous friction of the cantilever with the liquid. This force should be considered when interpreting experimental results and any calculated material properties. In this paper, a numerical model is presented to study the influence of the drag force on experimental data obtained from AFM measurements using computational fluid dynamics (CFD) simulation. The model provides quantification of the drag force in AFM measurements of soft specimens in fluids. The numerical predictions were compared with experimental data obtained using AFM with a V-shaped cantilever fitted with a pyramidal tip. Tip velocities ranging from 1.05 to 105 μm/s were employed in water, polyethylene glycol and glycerol with the platform approaching from a distance of 6000 nm. The model was also compared with an existing analytical model. Good agreement was observed between numerical results, experiments and analytical predictions. Accurate predictions were obtained without the need for extrapolation of experimental data. In addition, the model can be employed over the range of tip geometries and velocities typically utilized in AFM measurements. PMID:25080275
Notes on aerodynamic forces on airship hulls
NASA Technical Reports Server (NTRS)
Tuckerman, L B
1923-01-01
For a first approximation the air flow around the airship hull is assumed to obey the laws of perfect (i.e. free from viscosity) incompressible fluid. The flow is further assumed to be free from vortices (or rotational motion of the fluid). These assumptions lead to very great simplifications of the formulae used but necessarily imply an imperfect picture of the actual conditions. The value of the results depends therefore upon the magnitude of the forces produced by the disturbances in the flow caused by viscosity with the consequent production of vortices in the fluid. If these are small in comparison with the forces due to the assumed irrotational perfect fluid flow the results will give a good picture of the actual conditions of an airship in flight.
McCallen, R
2002-09-01
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at NASA Ames Research Center on September 23, 2002. The purpose of the meeting was to present and discuss technical details on the experimental and computational work in progress and future project plans. Representatives from the Department of Energy (DOE)/Office of Energy Efficiency and Renewable Energy/Office of FreedomCAR & Vehicle Technologies, Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratories (SNL), NASA Ames Research Center (NASA), University of Southern California (USC), California Institute of Technology (Caltech), Georgia Tech Research Institute (GTRI), Argonne National Laboratory (ANL), Freightliner, and Portland State University participated in the meeting. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items. The meeting began with an introduction by the Project Lead Rose McCallen of LLNL, where she emphasized that the world energy consumption is predicted to relatively soon exceed the available resources (i.e., fossil, hydro, non-breeder fission). This short fall is predicted to begin around the year 2050. Minimizing vehicle aerodynamic drag will significantly reduce our Nation's dependence on foreign oil resources and help with our world-wide fuel shortage. Rose also mentioned that educating the populace and researchers as to our world energy issues is important and that our upcoming United Engineering Foundation (UEF) Conference on ''The Aerodynamics of Heavy Vehicles: Trucks, Busses, and Trains'' was one way our DOE Consortium was doing this. Mentioned were the efforts of Fred Browand from USC in organizing and attracting internationally recognized speakers to the Conference. Rose followed with an overview of the DOE project goals, deliverables, and FY03 activities. The viewgraphs are attached at the end of this report. Sid Diamond of DOE
The Aerodynamic Forces on Airship Hulls
NASA Technical Reports Server (NTRS)
Munk, M. M.
1979-01-01
The new method for making computations in connection with the study of rigid airships, which was used in the investigation of Navy's ZR-1 by the special subcommittee of the National Advisory Committee for Aeronautics appointed for this purpose is presented. The general theory of the air forces on airship hulls of the type mentioned is described and an attempt was made to develop the results from the very fundamentals of mechanics.
Properties of ion-particle interaction and the ion drag force in complex (dusty) plasmas
Khrapak, Sergey A.
2009-11-10
In this paper a concise overview of recent results concerning the properties of ion-particle interaction and the ion drag force in complex (dusty) plasmas is presented. Two main theoretical approaches to calculate the ion drag force--binary collision and linear plasma response formalisms are discussed. When possible, theoretical results are compared with the results from experiments and numerical simulations.
Hovering flight in the honeybee Apis mellifera: kinematic mechanisms for varying aerodynamic forces.
Vance, Jason T; Altshuler, Douglas L; Dickson, William B; Dickinson, Michael H; Roberts, Stephen P
2014-01-01
During hovering flight, animals can increase the wing velocity and therefore the net aerodynamic force per stroke by increasing wingbeat frequency, wing stroke amplitude, or both. The magnitude and orientation of aerodynamic forces are also influenced by the geometric angle of attack, timing of wing rotation, wing contact, and pattern of deviation from the primary stroke plane. Most of the kinematic data available for flying animals are average values for wing stroke amplitude and wingbeat frequency because these features are relatively easy to measure, but it is frequently suggested that the more subtle and difficult-to-measure features of wing kinematics can explain variation in force production for different flight behaviors. Here, we test this hypothesis with multicamera high-speed recording and digitization of wing kinematics of honeybees (Apis mellifera) hovering and ascending in air and hovering in a hypodense gas (heliox: 21% O2, 79% He). Bees employed low stroke amplitudes (86.7° ± 7.9°) and high wingbeat frequencies (226.8 ± 12.8 Hz) when hovering in air. When ascending in air or hovering in heliox, bees increased stroke amplitude by 30%-45%, which yielded a much higher wing tip velocity relative to that during simple hovering in air. Across the three flight conditions, there were no statistical differences in the amplitude of wing stroke deviation, minimum and stroke-averaged geometric angle of attack, maximum wing rotation velocity, or even wingbeat frequency. We employed a quasi-steady aerodynamic model to estimate the effects of wing tip velocity and geometric angle of attack on lift and drag. Lift forces were sensitive to variation in wing tip velocity, whereas drag was sensitive to both variation in wing tip velocity and angle of attack. Bees utilized kinematic patterns that did not maximize lift production but rather maintained lift-to-drag ratio. Thus, our data indicate that, at least for honeybees, the overall time course of wing angles is
Variations of Drag Forces on Two Close-Following Vehicles in a Back-to-Back Configuration
NASA Astrophysics Data System (ADS)
Marcu, Bogdan; Browand, Fred; Hammache, Mustapha
1998-11-01
Measurements of drag, side forces and yawing moment are made for each of a two-vehicle platoon, using 1/8 scale models of 1991 Chevy Lumina minivans equipped with force balances. The models are placed in a wind tunnel in a close following configuration, but with the trailing car placed in reverse - with its back forward towards the leading car - a configuration referred to as a "back-to-back configuration". The vehicle models are supported above a ground plane whose surface is porous. The boundary layer forming on the ground plane is removed by applying a small suction on the porous surface. Measurements are made for longitudinal spacing ranging from 0 to 0.4 vehicle lengths and alignments in the range of 0.025 car widths left to 0.025 car widths right of the centered position Meas urements reveal a very surprising phenomenon: the aerodynamic drag force on the leading vehicle is found to vary from a low value of 0.45 at zero spacing to a peak value of 0.95-1.0 at a spacing of approximately 0.08 vehicle lengths. For spacing values larger than 0.1 vehicle lengths the leading vehicle drag quickly diminishes to a 0.6-0.65 value. Hysteresis is observed. A discussion of this phenomenon is provided along with a possible explanation based on hot wire and DPIV intervehicle flow measurements.
Notes on aerodynamic forces 1 : rectilinear motion
NASA Technical Reports Server (NTRS)
Munk, Max M
1922-01-01
The study of the motion of perfect fluids is of paramount importance for the understanding of the chief phenomena occurring in the air surrounding an aircraft, and for the numerical determination of their effects. The author recently successfully employed some simple methods for the investigation of the flow of a perfect fluid that have never been mentioned in connection with aeronautical problems. These methods appeal particularly to the engineer who is untrained in performing laborious mathematical computations, as they do away with these and allow one to obtain many interesting results by the mere application of some general and well-known principles of mechanics. Discussed here are the kinetic energy of moving fluids, the momentum of a body in a perfect fluid, two dimensional flow, three dimensional flow, and the distribution of the transverse forces of very elongated surfaces of revolution.
Aerodynamic force variation in an inclined hovering motion by kinematic and geometric controls
NASA Astrophysics Data System (ADS)
Park, Hyungmin; Choi, Haecheon
2009-11-01
Due to the excellent flight capability with a high maneuverability, dragonfly flight has been a great interest in various fields. In the present study, we construct a one-paired dynamically scaled dragonfly wing model, perform an inclined hovering motion by wing flapping in a white-oil tank, and measure the normal and tangential forces on the wing. First, we investigate the effect of kinematic parameters of wing motion such as the attack angle (α), pitching duration, pitching timing, etc. The Reynolds number is 1,900 or 2,430 depending on the wing shape. We find that the aerodynamic forces vary greatly with these kinematic parameters. On the other hand, the corrugation on the wing surface has been found to increase the lift force in gliding flight. In this study, we investigate the effect of surface corrugation on the force of the flapping wing. With the corrugation, the drag force slightly increases during a downstroke (high α) and the lift force increases during an upstroke (small α), respectively, resulting in the increase of the mean vertical force by 10 ˜30% depending on the wing trajectory. We further investigate the force variation by kinematic and geometric controls using flow visualization and the result will be shown in the presentation.
NASA Technical Reports Server (NTRS)
Haviland, J. K.; Yoo, Y. S.
1976-01-01
Expressions for calculation of subsonic and supersonic, steady and unsteady aerodynamic forces are derived, using the concept of aerodynamic elements applied to the downwash velocity potential method. Aerodynamic elements can be of arbitrary out of plane polygon shape, although numerical calculations are restricted to rectangular elements, and to the steady state case in the supersonic examples. It is suggested that the use of conforming, in place of rectangular elements, would give better results. Agreement with results for subsonic oscillating T tails is fair, but results do not converge as the number of collocation points is increased. This appears to be due to the form of expression used in the calculations. The methods derived are expected to facilitate automated flutter analysis on the computer. In particular, the aerodynamic element concept is consistent with finite element methods already used for structural analysis. The method is universal for the complete Mach number range, and, finally, the calculations can be arranged so that they do not have to be repeated completely for every reduced frequency.
An integrated CFD/experimental analysis of aerodynamic forces and moments
NASA Technical Reports Server (NTRS)
Melton, John E.; Robertson, David D.; Moyer, Seth A.
1989-01-01
Aerodynamic analysis using computational fluid dynamics (CFD) is most fruitful when it is combined with a thorough program of wind tunnel testing. The understanding of aerodynamic phenomena is enhanced by the synergistic use of both analysis methods. A technique is described for an integrated approach to determining the forces and moments acting on a wind tunnel model by using a combination of experimentally measured pressures and CFD predictions. The CFD code used was FLO57 (an Euler solver) and the wind tunnel model was a heavily instrumented delta wing with 62.5 deg of leading-edge sweep. A thorough comparison of the CFD results and the experimental data is presented for surface pressure distributions and longitudinal forces and moments. The experimental pressures were also integrated over the surface of the model and the resulting forces and moments are compared to the CFD and wind tunnel results. The accurate determination of various drag increments via the combined use of the CFD and experimental pressures is presented in detail.
Greenman, R; Dunn, T; Owens, J; Laskowski, G; Flowers, D; Browand, F; Knight, A; Hammache, M; Leoard, A; Rubel, M; Salari, K; Rutledge, W; Ross, J; Satran, D; Heineck, J T; Walker, S; Driver, D; Storms, B
2001-05-14
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory on March 28 and 29, 2001. The purpose of the meeting was to present and discuss technical details on the experimental and computational work in progress and future project plans. Due to the large participation from industry and other research organizations, a large portion of the meeting (all of the first day and part of the second day) was devoted to the presentation and discussion of industry's perspective and work being done by other organizations on the demonstration of commercial software and the demonstration of a drag reduction device. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items.
McCallen, R; Salari, K; Ortega, J; Browand, F; Hammache, M; Hsu, T Y; Arcas, D; Leoard, A; Chatelain, P; Rubel, M; Roy, C; DeChant, L; Hassan, B; Ross, J; Satran, D; Walker, S; Heineck, J T; Englar, R; Pointer, D; Sofu, T
2003-05-01
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory on May 29-30, 2003. The purpose of the meeting was to present and discuss suggested guidance and direction for the design of drag reduction devices determined from experimental and computational studies. Representatives from the Department of Energy (DOE)/Office of Energy Efficiency and Renewable Energy/Office of FreedomCAR & Vehicle Technologies, Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratories (SNL), NASA Ames Research Center (NASA), University of Southern California (USC), California Institute of Technology (Caltech), Georgia Tech Research Institute (GTRI), Argonne National Laboratory (ANL), Clarkson University, and PACCAR participated in the meeting. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, provides some highlighted items, and outlines the future action items.
The Aerodynamic Drag of Flying-boat Hull Model as Measured in the NACA 20-foot Wind Tunnel I.
NASA Technical Reports Server (NTRS)
Hartman, Edwin P
1935-01-01
Measurements of aerodynamic drag were made in the 20-foot wind tunnel on a representative group of 11 flying-boat hull models. Four of the models were modified to investigate the effect of variations in over-all height, contours of deck, depth of step, angle of afterbody keel, and the addition of spray strips and windshields. The results of these tests, which cover a pitch-angle range from -5 to 10 degrees, are presented in a form suitable for use in performance calculations and for design purposes.
Measurement of the ion drag force on free falling microspheres in a plasma
Hirt, Markus; Block, Dietmar; Piel, Alexander
2004-12-01
Experiments on the quantitative determination of the ion drag force on free-falling dust particles in a collisionless regime are presented. The ion drag forces are measured for ion energies up to 40 eV and the obtained results are compared in detail with theories. Good agreement is found with the Barnes model [Barnes et al., Phys. Rev. Lett. 68, 313 (1992)] of the ion drag force for high ion energies (E>3 eV). At lower ion energies the model of Khrapak [Khrapak et al., Phys. Rev. Lett. 90, 225002 (2003)] is found to give a better description of the capture of slowly streaming ions by highly charged particles.
Surface adhesive forces: a metric describing the drag-reducing effects of superhydrophobic coatings.
Cheng, Mengjiao; Song, Mengmeng; Dong, Hongyu; Shi, Feng
2015-04-01
Nanomaterials with superhydrophobic properties are promising as drag-reducing coatings. However, debates regarding whether superhydrophobic surfaces are favorable for drag reduction require further clarification. A quantified water adhesive force measurement is proposed as a metric and its effectiveness demonstrated using three typical superhydrophobic coatings on model ships with in situ sailing tests. PMID:25418808
Computation of Ion Drag Force and Charge on a Static Spherical Dust Grain in RF Plasma
Ikkurthi, V. R.; Melzer, A.; Matyash, K.; Schneider, R.
2008-09-07
The ion drag force and charge on a spherical dust grain located in RF discharge plasma is computed using a 3-dimensional Particle-Particle Particle-Mesh (P3M) code. Our plasma model includes finite-size effects for dust grains and allows to self-consistently resolve the dust grain charging due to absorption of plasma electrons and ions. Ion drag and dust charge have been computed for various sizes of dust particles placed at various locations in the discharge. The results for ion drag have been compared with previous collisionless models and affect of collisions on drag has been discussed in detail.
Aerodynamic drag and fuel spreading measurements in a simulated scramjet combustion module
NASA Technical Reports Server (NTRS)
Povinelli, L. A.
1974-01-01
The drag of a simulated scramjet combustion module was measured at Mach 2, 2.5, and 3. The combustor was rectangular in cross section and incorporated six swept fuel injector struts. The effect of strut leading edge radius, position of maximum thickness, thickness ratio, sweep angle, and strut length on the drag was determined. Reduction in thickness ratio had the largest effect on drag reduction. Sweeping the struts upstream yielded the same drag as sweeping the struts downstream and potentially offers the advantages of increased mixing time for the fuel. Helium injection was used to simulate hydrogen fuel. The interstrut spacing required to achieve good distribution of fuel was was found to be about 10 jet diameters. The contribution of helium injection to drag reduction was small.
Direct Measurements of Drag Forces in C. elegans Crawling Locomotion
Rabets, Yegor; Backholm, Matilda; Dalnoki-Veress, Kari; Ryu, William S.
2014-01-01
With a simple and versatile microcantilever-based force measurement technique, we have probed the drag forces involved in Caenorhabditis elegans locomotion. As a worm crawls on an agar surface, we found that substrate viscoelasticity introduces nonlinearities in the force-velocity relationships, yielding nonconstant drag coefficients that are not captured by original resistive force theory. A major contributing factor to these nonlinearities is the formation of a shallow groove on the agar surface. We measured both the adhesion forces that cause the worm’s body to settle into the agar and the resulting dynamics of groove formation. Furthermore, we quantified the locomotive forces produced by C. elegans undulatory motions on a wet viscoelastic agar surface. We show that an extension of resistive force theory is able to use the dynamics of a nematode’s body shape along with the measured drag coefficients to predict the forces generated by a crawling nematode. PMID:25418179
The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J
NASA Technical Reports Server (NTRS)
House, R O
1938-01-01
The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.
Drag forces on oscillating cylinders in a uniform flow
Kato, M.; Abe, T.; Kumakiri, T.; Tamiya, M.
1985-03-01
This paper describes the drag coefficients of cylinders oscillated in both in-line and transverse directions to a uniform flow. The drag coefficients C /SUB D/ have been obtained experimentally over a wide range of oscillation frequencies, amplitude and flow velocities for the cylinders of various diameters under simulated practical offshore conditions. New expressions are proposed for the drag coefficients C /SUB D/ of an oscillating cylinder in a uniform flow. The boundary between the regions, is clearly established by employing the Keulegan-Carpenter number and the reduced velocity as dimensionless numbers. These dimensionless numbers also clearly describe C /SUB D/ variation within the region of rapid C /SUB D/ value decrease.
Scattering by a Schwarzschild black hole of particles undergoing drag force effects
NASA Astrophysics Data System (ADS)
Bini, Donato; Geralico, Andrea
2016-07-01
The scattering of massive particles by a Schwarzschild black hole also undergoing a drag force is considered. The latter is modeled as a viscous force acting on the orbital plane, with components proportional to the associated particle 4-velocity components. The energy and angular momentum losses as well as the dependence of the hyperbolic scattering angle on the strength of the drag are investigated in situations where strong field effects cause large deflections.
Drag force of Anisotropic plasma at finite U(1) chemical potential
NASA Astrophysics Data System (ADS)
Cheng, Long; Ge, Xian-Hui; Wu, Shang-Yu
2016-05-01
We perform the calculation of the drag force acting on a massive quark moving through an anisotropic N=4 SU(N) Super Yang-Mills plasma in the presence of a U(1) chemical potential. We present the numerical results for any value of the anisotropy and arbitrary direction of the quark velocity with respect to the direction of the anisotropy. We find the effect of the chemical potential or charge density will enhance the drag force for our charged solution.
Alignment of dust particles by ion drag forces in subsonic flows
Piel, Alexander
2011-07-15
The role of ion drag forces for the alignment of dust particles is studied for subsonic flows. While alignment by wake-field attraction is a well known mechanism for supersonic flows, it is argued here that ion-scattering forces become more important in subsonic ion flows. A model of non-overlapping collisions is introduced and numerical results are discussed. For typical conditions of dusty plasma experiments, alignment by drag forces is found strong enough to overcome the destabilizing force from Coulomb repulsion between dust particles. It turns out that the major contribution to the horizontal restoring force originates from the transverse momentum transfer, which is usually neglected in ion drag force calculations because of an assumed rotational symmetry of the flow.
Dudek, D.; Fletcher, T.H.
1987-02-01
When a heated solid sphere is introduced into an ambient fluid, a natural convective flow occurs which results in a drag force on the sphere. This study involves the numerical calculation of both the steady-state and the transient natural convective drag force around spheres at low Grashof numbers. Numerical techniques are taken from Geoola and Cornish. An empirical expression is suggested for the total drag coefficient for Grashof numbers ranging from 4 x 10/sup -4/ to 0.5 and Prandtl number = 0.72: log C/sub DT/ = 1.25 + 0.31 log Gr - 0.097(log Gr)/sup 2/. The dimensionless time required to reach 90% of the steady-state drag force can be approximated by the second-order polynomial: log t/sub 90%/ = 1.32 - log Gr - 0.11(Gr)/sup 2/.
Drag forces on oscillating cylinders in a uniform flow
Kato, M.; Abe, T.; Kumakiri, T.; Tamiya, M.
1983-05-01
This paper describes the drag coefficients of cylinders oscillated in both in-line and transverse directions to a uniform flow. The drag coefficients C/SUB D/ have been obtained experimentally over a wide range of oscillating frequencies, amplitude and flow velocities for the cylinders of various diameters under simulated practical offshore conditions. The boundary between the regions, where C/SUB D/ approx. =1 and C/SUB D/ <1, are clearly established by employing the Keulegan-Carpenter number and the Reduced Velocity as dimensionless numbers. These numbers also describe C/SUB D/ variation within the region of rapid C/SUB D/ value decrease. Recommendations are offered for determining C/SUB D/ values in order to predict the dynamic response of risers under actual offshore conditions.
Skin-friction drag analysis from the forced convection modeling in simplified underwater swimming.
Polidori, G; Taïar, R; Fohanno, S; Mai, T H; Lodini, A
2006-01-01
This study deals with skin-friction drag analysis in underwater swimming. Although lower than profile drag, skin-friction drag remains significant and is the second and only other contribution to total drag in the case of underwater swimming. The question arises whether varying the thermal gradient between the underwater swimmer and the pool water may modify the surface shear stress distribution and the resulting skin-friction drag acting on a swimmer's body. As far as the authors are aware, such a question has not previously been addressed. Therefore, the purpose of this study was to quantify the effect of this thermal gradient by using the integral formalism applied to the forced convection theory. From a simplified model in a range of pool temperatures (20-30 degrees C) it was demonstrated that, whatever the swimming speeds, a 5.3% reduction in the skin-friction drag would occur with increasing average boundary-layer temperature provided that the flow remained laminar. However, as the majority of the flow is actually turbulent, a turbulent flow analysis leads to the major conclusion that friction drag is a function of underwater speed, leading to a possible 1.5% reduction for fast swimming speeds above 1m/s. Furthermore, simple correlations between the surface shear stress and resulting skin-friction drag are derived in terms of the boundary-layer temperature, which may be readily used in underwater swimming situations. PMID:16153653
NASA Technical Reports Server (NTRS)
Saltzman, Edwin J.; Wang, K. Charles; Iliff, Kenneth W.
2002-01-01
This report examines subsonic flight-measured lift and drag characteristics of seven lifting-body and wing-body reentry vehicle configurations with truncated bases. The seven vehicles are the full-scale M2-F1, M2-F2, HL-10, X-24A, X-24B, and X-15 vehicles and the Space Shuttle Enterprise. Subsonic flight lift and drag data of the various vehicles are assembled under aerodynamic performance parameters and presented in several analytical and graphical formats. These formats are intended to unify the data and allow a greater understanding than individually studying the vehicles allows. Lift-curve slope data are studied with respect to aspect ratio and related to generic wind-tunnel model data and to theory for low-aspect-ratio platforms. The definition of reference area is critical for understanding and comparing the lift data. The drag components studied include minimum drag coefficient, lift-related drag, maximum lift-to drag ratio, and, where available, base pressure coefficients. The influence of forebody drag on afterbody and base drag at low lift is shown to be related to Hoerner's compilation for body, airfoil, nacelle, and canopy drag. This feature may result in a reduced need of surface smoothness for vehicles with a large ratio of base area to wetted area. These analyses are intended to provide a useful analytical framework with which to compare and evaluate new vehicle configurations of the same generic family.
NASA Technical Reports Server (NTRS)
Arnaiz, H. H.
1975-01-01
As part of a NASA program to evaluate current methods of predicting the performance of large, supersonic airplanes, the drag of the XB-70 airplane was measured accurately in flight at Mach numbers from 0.75 to 2.5. This paper describes the techniques used to determine engine net thrust and the drag forces charged to the propulsion system that were required for the in-flight drag measurements. The accuracy of the measurements and the application of the measurement techniques to aircraft with different propulsion systems are discussed. Examples of results obtained for the XB-70 airplane are presented.
Browand, F; Heineck, J T; Leonard, A; McBride, D; McCallen, R; Ross, J; Rutledge, W; Salari, K; Storms, B
1998-10-01
A Working Group 1Meeting on Heavy Vehicle Aerodynamic Drag was held at NASA Ames Research Center, Moffett Field, California on October 22, 1998. The purpose of the meeting was to present an overview of the computational and experimental approach for modeling the integrated tractor-trailer benchmark geometry called the Sandia IModel and to review NASA' s test plan for their experiments in the 7 ft x 10 ft wind tunnel. The present and projected funding situation was also discussed. Presentations were given by representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT). Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratories (SNL), and NASA Ames Research Center. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions. and outlines the future action items.
Salari, K; Dunn, T; Ortega, J; Yen-Nakafuji, D; Browand, F; Arcas, D; Jammache, M; Leoard, A; Chatelain, P; Rubel, M; Rutledge, W; McWherter-Payne, M; Roy, Ca; Ross, J; Satran, D; Heineck, J T; Storms, B; Pointer, D; Sofu, T; Weber, D; Chu, E; Hancock, P; Bundy, B; Englar, B
2002-08-22
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory on April 3 and 4, 2002. The purpose of the meeting was to present and discuss technical details on the experimental and computational work in progress and future project plans. Representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT), Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratories (SNL), NASA Ames Research Center, University of Southern California (USC), and California Institute of Technology (Caltech), Georgia Tech Research Institute (GTRI), and Argonne National Laboratory (ANL), Volvo Trucks, and Freightliner Trucks presented and participated in discussions. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items.
Ion drag force on a dust grain in a weakly ionized collisional plasma
Semenov, I. L.; Krivtsun, I. V.; Zagorodny, A. G.
2013-01-15
The problem of calculating the ion drag force acting on a dust grain immersed in a weakly ionized collisional plasma is studied using an approach based on the direct numerical solution of the Vlasov-Bhatnagar-Gross-Krook kinetic equations. A uniform subthermal flow of argon plasma past a spherical dust grain is considered. The numerical computations are performed for a wide range of plasma pressures. On the basis of the obtained results, the effect of ion-neutral collisions on the ion drag force is analyzed in a wide range of ion collisionality. In the collisionless limit, our results are shown to be in good agreement with the results obtained by the binary collision approach. As the ion collisionality increases, the ion drag force is found to decrease sharply and even become negative, i.e., directed oppositely to the plasma flow. A qualitative explanation of this effect is presented and a comparison of our results with those obtained using the drift diffusion approach is discussed. The velocity dependence of the ion drag force in the highly collisional regime is examined. The relationship between the ion and the neutral drag forces in the highly collisional limit is analyzed and the possibility of a superfluid-like behavior of dust grains is discussed.
Relationship between the ion drag and electric forces in dense dust clouds
Yaroshenko, V. V.; Khrapak, S. A.; Morfill, G. E.
2013-04-15
It is shown that the relation between the ion drag and electric forces is strongly dependent on the dust number density in complex plasmas. The effect of the particle size and discharge parameters on the force balance is investigated. Examples are given for realistic complex plasma parameters and comparison with microgravity experiments is presented.
Numerical stability in multifluid gas dynamics with implicit drag forces
NASA Astrophysics Data System (ADS)
Ramshaw, J. D.; Chang, C. H.
2015-10-01
The numerical stability of a conventional explicit numerical scheme for solving the inviscid multifluid dynamical equations describing a multicomponent gas mixture is investigated both analytically and computationally. Although these equations do not explicitly contain diffusion terms, it is well known that they reduce to a single-fluid diffusional description when the drag coefficients in the species momentum equations are large. The question then arises as to whether their numerical solution is subject to a diffusional stability restriction on the time step in addition to the usual Courant sound-speed stability condition. An analytical stability analysis is performed for the special case of a quiescent binary gas mixture with equal sound speeds and temperatures. It is found that the Courant condition is always sufficient to ensure stability, so that no additional diffusional stability restriction arises for any value of the drag coefficient, however large. This result is confirmed by one-dimensional computational results for binary and ternary mixtures with unequal sound speeds, which remain stable even when the time step exceeds the usual diffusional limit by factors of order 100.
Aerodynamic forces and vortical structures in flapping butterfly's forward flight
NASA Astrophysics Data System (ADS)
Yokoyama, Naoto; Senda, Kei; Iima, Makoto; Hirai, Norio
2013-02-01
Forward flights of a bilaterally symmetrically flapping butterfly modeled as a four-link rigid-body system consisting of a thorax, an abdomen, and left and right wings are numerically simulated. The joint motions of the butterflies are adopted from experimental observations. Three kinds of the simulations, distinguished by ways to determine the position and attitude of the thorax, are carried out: a tethered simulation, a prescribed simulation, and free-flight simulations. The upward and streamwise forces as well as the wake structures in the tethered simulation, where the thorax of the butterfly is fixed, reasonably agree with those in the corresponding tethered experiment. In the prescribed simulation, where the thoracic trajectories as well as the joint angles are given by those observed in a free-flight experiment, it is confirmed that the butterfly can produce enough forces to achieve the flapping flights. Moreover, coherent vortical structures in the wake and those on the wings are identified. The generation of the aerodynamic forces due to the vortical structures are also clarified. In the free-flight simulation, where only the joint angles are given as periodic functions of time, it is found that the free flight is longitudinally unstable because the butterfly cannot maintain the attitude in a proper range. Focusing on the abdominal mass, which largely varies owing to feeding and metabolizing, we have shown that the abdominal motion plays an important role in periodic flights. The necessity of control of the thoracic attitude for periodic flights and maneuverability is also discussed.
Chaudhuri, Manis; Khrapak, Sergei A.; Morfill, Gregor E.
2008-09-07
The ion drag force acting on a small absorbing spherical grain has been calculated analytically in highly collisional plasma with slowly drifting ions taking into account plasma production and loss mechanisms in the vicinity of the grain. It is shown that both the magnitude and direction of the ion drag force are strongly influenced by the plasma production and loss mechanisms. The parameter regimes for the 'positive' and 'negative' ion drag forces acting on an absorbing grain have been identified.
Liu, Runcong; Roman, Marisa; Yang, Guoliang
2010-06-01
We describe a method to correct the errors induced by viscous drag on the cantilever in macromolecular manipulation experiments using the atomic force microscope. The cantilever experiences a viscous drag force in these experiments because of its motion relative to the surrounding liquid. This viscous force superimposes onto the force generated by the macromolecule under study, causing ambiguity in the experimental data. To remove this artifact, we analyzed the motions of the cantilever and the liquid in macromolecular manipulation experiments, and developed a novel model to treat the viscous drag on the cantilever as the superposition of the viscous force on a static cantilever in a moving liquid and that on a bending cantilever in a static liquid. The viscous force was measured under both conditions and the results were used to correct the viscous drag induced errors from the experimental data. The method will be useful for many other cantilever based techniques, especially when high viscosity and high cantilever speed are involved. PMID:20590242
Liu, Runcong; Roman, Marisa; Yang, Guoliang
2010-01-01
We describe a method to correct the errors induced by viscous drag on the cantilever in macromolecular manipulation experiments using the atomic force microscope. The cantilever experiences a viscous drag force in these experiments because of its motion relative to the surrounding liquid. This viscous force superimposes onto the force generated by the macromolecule under study, causing ambiguity in the experimental data. To remove this artifact, we analyzed the motions of the cantilever and the liquid in macromolecular manipulation experiments, and developed a novel model to treat the viscous drag on the cantilever as the superposition of the viscous force on a static cantilever in a moving liquid and that on a bending cantilever in a static liquid. The viscous force was measured under both conditions and the results were used to correct the viscous drag induced errors from the experimental data. The method will be useful for many other cantilever based techniques, especially when high viscosity and high cantilever speed are involved. PMID:20590242
Measurement of the ion drag force in a collisionless plasma with strong ion-grain coupling
Nosenko, V.; Fisher, R.; Merlino, R.; Khrapak, S.; Morfill, G.; Avinash, K.
2007-10-15
The ion drag force acting on dust grains was measured experimentally in a low-pressure Ar plasma in the regime of strong ion-grain coupling. Argon ions were drifting in the axial ambipolar electric field naturally present in a hot-filament dc discharge plasma. Following the method of Hirt et al. [Phys. Plasmas 11, 5690 (2004)], hollow glass microspheres were dropped into the plasma and allowed to fall due to gravity. The ion drag force was derived from the particle trajectory deflection from the vertical direction. The result is in reasonable agreement with a theoretical model that takes strong ion-grain coupling into account.
Noncollinear drag force in Bose-Einstein condensates with Weyl spin-orbit coupling
NASA Astrophysics Data System (ADS)
Liao, Renyuan; Fialko, Oleksandr; Brand, Joachim; Zülicke, Ulrich
2016-02-01
We consider the motion of a pointlike impurity through a three-dimensional two-component Bose-Einstein condensate subject to Weyl spin-orbit coupling. Using linear-response theory, we calculate the drag force felt by the impurity and the associated anisotropic critical velocity from the spectrum of elementary excitations. The drag force is shown to be generally not collinear with the velocity of the impurity. This unusual behavior is a consequence of condensation into a finite-momentum state due to the spin-orbit coupling.
Effects of turbulence on the drag force on a golf ball
NASA Astrophysics Data System (ADS)
Cross, Rod
2016-09-01
Measurements are presented of the drag force on a golf ball dropped vertically into a tank of water. As observed previously in air, the drag coefficient drops sharply when the flow becomes turbulent. The experiment would be suitable for undergraduate students since it can be undertaken at low ball speeds and since the effects of turbulence are easily observed on video film. A modified golf ball was used to show how a ball with a smooth and a rough side, such as a cricket ball, is subject to a side force when the ball surface itself is asymmetrical in the transverse direction.
Experimental characterization of high speed centrifugal compressor aerodynamic forcing functions
NASA Astrophysics Data System (ADS)
Gallier, Kirk
The most common and costly unexpected post-development gas turbine engine reliability issue is blade failure due to High Cycle Fatigue (HCF). HCF in centrifugal compressors is a coupled nonlinear fluid-structure problem for which understanding of the phenomenological root causes is incomplete. The complex physics of this problem provides significant challenges for Computational Fluid Dynamics (CFD) techniques. Furthermore, the available literature fails to address the flow field associated with the diffuser potential field, a primary cause of forced impeller vibration. Because of the serious nature of HCF, the inadequacy of current design approaches to predict HCF, and the fundamental lack of benchmark experiments to advance the design practices, there exists a need to build a database of information specific to the nature of the diffuser generated forcing function as a foundation for understanding flow induced blade vibratory failure. The specific aim of this research is to address the fundamental nature of the unsteady aerodynamic interaction phenomena inherent in high-speed centrifugal compressors wherein the impeller exit flow field is dynamically modulated by the vaned diffuser potential field or shock structure. The understanding of this unsteady aerodynamic interaction is fundamental to characterizing the impeller forcing function. Unsteady static pressure measurement at several radial and circumferential locations in the vaneless space offer a depiction of pressure field radial decay, circumferential variation and temporal fluctuation. These pressure measurements are coupled with high density, full field measurement of the velocity field within the diffuser vaneless space at multiple spanwise positions. The velocity field and unsteady pressure field are shown to be intimately linked. A strong momentum gradient exiting the impeller is shown to extend well across the vaneless space and interact with the diffuser vane leading edge. The deterministic unsteady
Lift vs. drag based mechanisms for vertical force production in the smallest flying insects.
Jones, S K; Laurenza, R; Hedrick, T L; Griffith, B E; Miller, L A
2015-11-01
We used computational fluid dynamics to determine whether lift- or drag-based mechanisms generate the most vertical force in the flight of the smallest insects. These insects fly at Re on the order of 4-60 where viscous effects are significant. Detailed quantitative data on the wing kinematics of the smallest insects is not available, and as a result both drag- and lift-based strategies have been suggested as the mechanisms by which these insects stay aloft. We used the immersed boundary method to solve the fully-coupled fluid-structure interaction problem of a flexible wing immersed in a two-dimensional viscous fluid to compare three idealized hovering kinematics: a drag-based stroke in the vertical plane, a lift-based stroke in the horizontal plane, and a hybrid stroke on a tilted plane. Our results suggest that at higher Re, a lift-based strategy produces more vertical force than a drag-based strategy. At the Re pertinent to small insect hovering, however, there is little difference in performance between the two strategies. A drag-based mechanism of flight could produce more vertical force than a lift-based mechanism for insects at Re<5; however, we are unaware of active fliers at this scale. PMID:26300066
Reynolds-number dependence of turbulent skin-friction drag reduction induced by spanwise forcing
NASA Astrophysics Data System (ADS)
Gatti, Davide; Quadrio, Maurizio
2016-09-01
This paper examines how increasing the value of the Reynolds number $Re$ affects the ability of spanwise-forcing techniques to yield turbulent skin-friction drag reduction. The considered forcing is based on the streamwise-travelling waves of spanwise wall velocity (Quadrio {\\em et al. J. Fluid Mech.}, vol. 627, 2009, pp. 161--178). The study builds upon an extensive drag-reduction database created with Direct Numerical Simulation of a turbulent channel flow for two, 5-fold separated values of $Re$, namely $Re_\\tau=200$ and $Re_\\tau=1000$. The sheer size of the database, which for the first time systematically addresses the amplitude of the forcing, allows a comprehensive view of the drag-reducing characteristics of the travelling waves, and enables a detailed description of the changes occurring when $Re$ increases. The effect of using a viscous scaling based on the friction velocity of either the non-controlled flow or the drag-reduced flow is described. In analogy with other wall-based drag reduction techniques, like for example riblets, the performance of the travelling waves is well described by a vertical shift of the logarithmic portion of the mean streamwise velocity profile. Except when $Re$ is very low, this shift remains constant with $Re$, at odds with the percentage reduction of the friction coefficient, which is known to present a mild, logarithmic decline. Our new data agree with the available literature, which is however mostly based on low-$Re$ information and hence predicts a quick drop of maximum drag reduction with $Re$. The present study supports a more optimistic scenario, where for an airplane at flight Reynolds numbers a drag reduction of nearly 30\\% would still be possible thanks to the travelling waves.
Gutierrez, W.T.; Hassan, B.; Croll, R.H.; Rutledge, W.H.
1995-12-31
The focus of the research was to investigate the fundamental aerodynamics of the base flow of a tractor trailer that would prove useful in fluid flow management. Initially, industry design needs and constraints were defined. This was followed by an evaluation of state-of-the-art Navier-Stokes based computational fluid dynamics tools. Analytical methods were then used in combination with computational tools in a design process. Several geometries were tested at 1:8 scale in a low speed wind tunnel. In addition to the baseline geometry, base add-on devices of the class of ogival boattails and slants were analyzed.
Reduction of aerodynamic drag and fuel consumption for tractor-trailer vehicles
NASA Technical Reports Server (NTRS)
Muirhead, V. U.; Saltzman, E. J.
1979-01-01
Wind-tunnel tests were performed on a scale model of a cab-over-engine tractor-trailer vehicle and several modifications of the model. Results from two of the model configurations were compared with full-scale drag data obtained from similar configurations during coast-down tests. Reductions in fuel consumption derived from these tests are presented in terms of fuel quantity and dollar savings per vehicle year, based on an annual driving distance of 160,900 km (100,000 mi.). The projected savings varied from 13,001 (3435) to 25,848 (6829) liters (gallons) per year which translated to economic savings from $3435 to about $6829 per vehicle year for an operating speed of 88.5 km/h (55 mph) and wind speeds near the national average of 15.3 km/h (9.5 mph). The estimated cumulative fuel savings for the entire U.S. fleet of cab-over-engine tractor, van-type trailer combinations ranged from 4.18 million kl (26.3 million bbl) per year for a low-drag configuration to approximately twice that amount for a more advanced configuration.
Drag force on a spherical intruder in a granular bed at low Froude number.
Hilton, J E; Tordesillas, A
2013-12-01
The drag force on an object, or "intruder," in a granular material arises from interparticle friction, as well as the cyclic creation and buckling of force chains within the material. In contrast to fluids, for which drag forces are well understood, there is no straightforward relationship between speed and mean drag force in granular materials. We investigate spherical intruder particles of varying radii moving at low speeds through granular beds. The system can be parametrized using the dimensionless Froude number Fr=2v/√[gR], for intruders of radius R moving at a speed v. For frictional systems, we find the drag force obeys a linear relationship with Fr for low Froude numbers above Fr>1. For Fr<1 we observe a deviation from this linear trend. This transition can be explained by considering the characteristic inertial and gravitational granular time scales of the system. We show that a suitably normalized measure of dissipated power obeys a linear relationship with the imposed intruder velocity, independent of the intruder dimensions. This is found to hold even for particles with no friction, identifying a relationship between the imposed motion of the intruder and the resistance of the granular material to purely geometric rearrangements. PMID:24483432
Influence of a drag force on linear transport in low-density gases. Stability analysis
NASA Astrophysics Data System (ADS)
Pérez-Fuentes, José Carlos; Garzó, Vicente
2014-09-01
The transport coefficients of a dilute classical gas in the presence of a drag force proportional to the velocity of the particle are determined from the Boltzmann equation. The viscous drag force could model the friction of solid particles with a surrounding fluid (interstitial gas phase). First, when the drag force is the only external action on the state of the system, the Boltzmann equation admits a Maxwellian solution f0(v,t) with a time-dependent temperature. Then, the Boltzmann equation is solved by means of the Chapman-Enskog expansion around the local version of the distribution f0 to obtain the relevant transport coefficients of the system: the shear viscosity η, the thermal conductivity κ, and a new transport coefficient μ (which is also present in granular gases) relating the heat flux with the density gradient. The results indicate that while η is not affected by the drag force, the impact of this force on the transport coefficients κ and μ may be significant. Finally, a stability analysis of the linear hydrodynamic equations with respect to the time-dependent equilibrium state is performed, showing that the onset of instability is associated with the transversal shear mode that could be unstable for wave numbers smaller than a certain critical wave number.
Drag reduction in turbulent channel flow using bidirectional wavy Lorentz force
NASA Astrophysics Data System (ADS)
Huang, LePing; Choi, KwingSo; Fan, BaoChun; Chen, YaoHui
2014-11-01
Turbulent control and drag reduction in a channel flow via a bidirectional traveling wave induced by spanwise oscillating Lorentz force have been investigated in the paper. The results based on the direct numerical simulation (DNS) indicate that the bidirectional wavy Lorentz force with appropriate control parameters can result in a regular decline of near-wall streaks and vortex structures with respect to the flow direction, leading to the effective suppression of turbulence generation and significant reduction in skin-friction drag. In addition, experiments are carried out in a water tunnel via electro-magnetic (EM) actuators designed to produce the bidirectional traveling wave excitation as described in calculations. As a result, the actual substantial drag reduction is realized successfully in these experiments.
NASA Technical Reports Server (NTRS)
Muse, Thomas C.
1941-01-01
An investigation was made in the NACA 19-foot pressure wind tunnel to determine the effect of various win-gun installation on the aerodynamic characteristics of a model with an NACA low-drag wing. Measurements were made of lift and drag over an angle-of-attack range and for several values of dynamic pressure on a four-tenths scale model of a high-speed airplane equipped with the low-drag wing and with various wing-gun installations. Two installations were tested: one in which the blast tube and part of the gun barrel protrude ahead of the wing and another in which the guns is mounted wholly within the wing. Two types of openings for the latter installation were tested. For each installation three simulated guns were mounted in each wing. The results are given in the form of nondimensional coefficients. The installations tested appear to have little effect on the maximum-lift coefficient of the model. However, the drag coefficient shows a definite change. The least adverse effect was obtained with the completely internal mounting and small nose entrance. The results indicate that a properly designed wing-gun installation will have very little adverse effect on the aerodynamic characteristics of the low-drag wing.
On the effect of sea spray on the aerodynamic surface drag under severe winds
NASA Astrophysics Data System (ADS)
Troitskaya, Yuliya; Ezhova, Ekaterina; Soustova, Irina; Zilitinkevich, Sergej
2016-05-01
We investigate the effect of the sea spray on the air-sea momentum exchange during the entire "life cycle" of a droplet, torn off the crest of a steep surface wave, and its fall down to the water, in the framework of a model covering the following aspects of the phenomenon: (1) motion of heavy particle in the driving air flow (equations of motion); (2) structure of the wind field (wind velocity, wave-induced disturbances, turbulent fluctuations); (3) generation of the sea spray; and (4) statistics of droplets (size distribution, wind speed dependence). It is demonstrated that the sea spray in strong winds leads to an increase in the surface drag up to 40 % on the assumption that the velocity profile is neutral.
Supej, M; Saetran, L; Oggiano, L; Ettema, G; Šarabon, N; Nemec, B; Holmberg, H-C
2013-02-01
This investigation was designed to (a) develop an individualized mechanical model for measuring aerodynamic drag (F(d) ) while ski racing through multiple gates, (b) estimate energy dissipation (E(d) ) caused by F(d) and compare this to the total energy loss (E(t) ), and (c) investigate the relative contribution of E(d) /E(t) to performance during giant slalom skiing (GS). Nine elite skiers were monitored in different positions and with different wind velocities in a wind tunnel, as well as during GS and straight downhill skiing employing a Global Navigation Satellite System. On the basis of the wind tunnel measurements, a linear regression model of drag coefficient multiplied by cross-sectional area as a function of shoulder height was established for each skier (r > 0.94, all P < 0.001). Skiing velocity, F(d) , E(t) , and E(d) per GS turn were 15-21 m/s, 20-60 N, -11 to -5 kJ, and -2.3 to -0.5 kJ, respectively. E(d) /E(t) ranged from ∼5% to 28% and the relationship between E(t) /v(in) and E(d) was r = -0.12 (all NS). In conclusion, (a) F(d) during alpine skiing was calculated by mechanical modeling, (b) E(d) made a relatively small contribution to E(t) , and (c) higher relative E(d) was correlated to better performance in elite GS skiers, suggesting that reducing ski-snow friction can improve this performance. PMID:23121340
ERIC Educational Resources Information Center
Vial, Alexandre
2007-01-01
We investigate the problem of the horizontal distance travelled by a mobile experiencing a quadratic drag force. We show that by introducing a normalized distance, the problem can be greatly simplified. In order to parametrize this distance, we use the Pearson VII function, and we find that the optimal launch angle as a function of the initial…
Projectile Motion with a Drag Force: Were the Medievals Right After All?
ERIC Educational Resources Information Center
La Rocca, Paola; Riggi, Francesco
2009-01-01
An educational and historical study of the projectile motion with drag forces dependent on speed shows, by simple results, that trajectories quite similar to those depicted before the Galilean era may be obtained with a realistic choice of quantities involved. Numerical simulations of the trajectory in space and velocity coordinates help us to…
Effect of the Drag Force on the Orbital Motion of the Broad-line Region Clouds
NASA Astrophysics Data System (ADS)
Khajenabi, Fazeleh
2016-09-01
We investigate the orbital motion of cold clouds in the broad-line region of active galactic nuclei subject to the gravity of a black hole, a force due to a non-isotropic central source, and a drag force proportional to the velocity square. The intercloud is described using the standard solutions for the advection-dominated accretion flows. The orbit of a cloud decays because of the drag force, but the typical timescale of clouds falling onto the central black hole is shorter compared to the linear drag case. This timescale is calculated when a cloud moves through a static or rotating intercloud. We show that when the drag force is a quadratic function of the velocity, irrespective of the initial conditions and other input parameters, clouds will generally fall onto the central region much faster than the age of whole system, and since cold clouds present in most of the broad-line regions, we suggest that mechanisms for the continuous creation of the clouds must operate in these systems.
McCallen, R.; Flowers, D.; Dunn, T.; Owens, J.; Browand, F.; Hammache, M.; Loenard, A.; Brady, M.; Salari, K.; Rutledge, W.; Scheckler, R.; Ross, J.; Storms, B.; Heineck, J.T.; Arledge, T
2000-05-15
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory on March 16, 2000. The purpose of the meeting was to present technical details on the experimental and computational plans and approaches and provide an update on progress in the analysis of experimental results, model developments, simulations, and an investigation of an aerodynamic device. The focus of the meeting was a review of University of Southern California's (USC) experimental plans and results, NASA Ames experimental plans, the computational results from Lawrence Livermore National Laboratory (LLNL) and Sandia National Laboratories (SNL) for the integrated tractor-trailer benchmark geometry called the Ground Transportation System (GTS) Model, and turbulence model development and benchmark simulation for a rounded cube from California Institute of Technology (Caltech). Much of the meeting discussion involved deficiencies in commercial software, needed modeling improvements, and the importance of detailed data for code validation. The present and projected budget and funding situation was also discussed. Presentations were given by representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT), LLNL, SNL, NASA Ames, USC, and Caltech. Representatives from Argonne National Laboratory also participated via telephone. This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items. There were 3 major issues raised at the meeting. (1) Our funding is inadequate to satisfy industries request for high Reynolds number experimentation and computation. Plans are to respond to the DOD and DOE requests for proposals, which require a 50-50 cost share with industry, to acquire funding for high Reynolds number experiments at NASA Ames. (2) The deficiencies in commercial software, the need for
NASA Technical Reports Server (NTRS)
Hawkins, Richard; Penland, Jim A.
1997-01-01
Observations have been made and reported that the experimental normal force coefficients at a constant angle of attack were constant with a variation of more than 2 orders of magnitude of Reynolds number at a free-stream Mach number M(sub infinity) of 8.00 and more than 1 order of magnitude variation at M(sub infinity) = 6.00 on the same body-wing hypersonic cruise configuration. These data were recorded under laminar, transitional, and turbulent boundary layer conditions with both hot-wall and cold-wall models. This report presents experimental data on 25 configurations of 17 models of both simple and complex geometry taken at M(sub infinity) = 6.00, 6.86, and 8.00 in 4 different hypersonic facilities. Aerodynamic calculations were made by computational fluid dynamics (CID) and engineering methods to analyze these data. The conclusions were that the normal force coefficients at a given altitude are constant with Reynolds numbers at hypersonic speeds and that the axial force coefficients recorded under laminar boundary-layer conditions at several Reynolds numbers may be plotted against the laminar parameter (the reciprocal of the Reynolds number to the one-half power) and extrapolated to the ordinate axis to determine the inviscid-wave-drag coefficient at the intercept.
Aerodynamics of Dragonfly in Forward Flight: Force measurements and PIV results
NASA Astrophysics Data System (ADS)
Hu, Zheng; Deng, Xinyan
2009-11-01
We used a pair of dynamically scaled robotic dragonfly model wings to investigate the aerodynamic effects of wing-wing interaction in dragonflies. We follow the wing kinematics of real dragonflies in forward flight, while systematically varied the phase difference between the forewing and hindwing. Instantaneous aerodynamic forces and torques were measured on both wings, while flow visualization and PIV results were obtained. The results show that, in forward flight, wing-wing interaction always enhances the aerodynamic forces on the forewing through an upwash brought by the hindwing, while reduces the forces on the hindwing through a downwash brought by the forewing.
Khrapak, S. A.; Nosenko, V.; Morfill, G. E.; Merlino, R.
2009-04-15
We point out a deficiency in our previous analytic calculation of the ion drag force for conditions of the experiment by Nosenko et al. [Phys. Plasmas 14, 103702 (2007)]. An inaccurate approximation is corrected and the ion drag force is recalculated. The improved model yields better overall agreement with the experimental results as compared to the original calculation.
Brady, M; Browand, F; McCallen, R; Ross, J; Salari, K
1999-03-01
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at Lawrence Livermore National Laboratory, Livermore, California on March 11, 1999. The purpose of the meeting was to present technical details on the experimental and computational plans and approaches and provide an update on progress in obtaining experimental results, model developments, and simulations. The focus of the meeting was a review of the experimental results for the integrated tractor-trailer benchmark geometry called the Sandia Model in the NASA Ames 7 ft x 10 ft wind tunnel. The present and projected budget and funding situation was also discussed. Presentations were given by representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT), Lawrence Livermore National Laboratory (LLNL), Sandia National Laboratories (SNL), University of Southern California (USC), California Institute of Technology (Caltech), and NASA Ames Research Center.This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items.
Ortega, Jason M.; Sabari, Kambiz
2006-03-07
An apparatus for reducing the aerodynamic base drag of a bluff body having a leading end, a trailing end, a top surface, opposing left and right side surfaces, and a base surface at the trailing end substantially normal to a longitudinal centerline of the bluff body, with the base surface joined (1) to the left side surface at a left trailing edge, (2) to the right side surface at a right trailing edge, and (3) to the top surface at a top trailing edge. The apparatus includes left and right vertical boattail plates which are orthogonally attached to the base surface of the bluff body and inwardly offset from the left and right trailing edges, respectively. This produces left and right vertical channels which generate, in a flowstream substantially parallel to the longitudinal centerline, respective left and right vertically-aligned vortical structures, with the left and right vertical boattail plates each having a plate width defined by a rear edge of the plate spaced from the base surface. Each plate also has a peak plate width at a location between top and bottom ends of the plate corresponding to a peak vortex of the respective vertically-aligned vortical structures.
Brady, M; Browand, F; Flowers, D; Hammache, M; Landreth, G; Leonard, A; McCallen, R; Ross, J; Rutledge, W; Salari, K
1999-08-16
A Working Group Meeting on Heavy Vehicle Aerodynamic Drag was held at University of Southern California, Los Angeles, California on July 30, 1999. The purpose of the meeting was to present technical details on the experimental and computational plans and approaches and provide an update on progress in obtaining experimental results, model developments, and simulations. The focus of the meeting was a review of University of Southern California's (USC) experimental plans and results and the computational results from Lawrence Livermore National Laboratory (LLNL) and Sandia National Laboratories (SNL) for the integrated tractor-trailer benchmark geometry called the Sandia Model. Much of the meeting discussion involved the NASA Ames 7 ft x 10 ft wind tunnel tests and the need for documentation of the results. The present and projected budget and funding situation was also discussed. Presentations were given by representatives from the Department of Energy (DOE) Office of Transportation Technology Office of Heavy Vehicle Technology (OHVT), LLNL, SNL, USC, and California Institute of Technology (Caltech). This report contains the technical presentations (viewgraphs) delivered at the Meeting, briefly summarizes the comments and conclusions, and outlines the future action items.
Origin of a depth-independent drag force induced by stirring in granular media.
Guillard, François; Forterre, Yoël; Pouliquen, Olivier
2015-02-01
Experiments have shown that when a horizontal cylinder rotates around the vertical axis in a granular medium, the drag force in the stationary regime becomes independent of the depth, in contradiction with the frictional picture stipulating that the drag should be proportional to the hydrostatic pressure. The goal of this study is to understand the origin of this depth independence of the granular drag. Intensive numerical simulations using the discrete element method are performed giving access to the stress distribution in the packing during the rotation of the cylinder. It is shown that the rotation induces a strong anisotropy in the stress distribution, leading to the formation of arches that screen the hydrostatic pressure in the vicinity of the cylinder and create a bubble of low pressure. PMID:25768492
The Effects of Drag and Tidal Forces on the Orbits of High-Velocity Clouds
NASA Astrophysics Data System (ADS)
Fernandes, Alexandre; Benjamin, R. A.
2013-06-01
Over the past several years, orbital constraints have been obtained for several high velocity cloud complexes surrounding the Milky Way: Complex GCP (Smith Cloud), Complex A, Complex H, Complex GCN, and the Magellanic Stream. We summarize what is known about the orbits of these clouds and and discuss how well each of these complexes fits a balistic trajectory, and discuss how the length of a complex across the sky is related to the inital "fragmentation" and velocity dispersion of the clouds. We then introduce gas drag into the simulation of the orbits of these complexes. We present analytical tests of our numerical method and characterize the departure of the clouds from the ballistic trajectory as a function of drag parameters (ambient gas density and velocity and cloud column density). Using the results of these simulations we comment on the survivability and ultimate fate of HVC in the context of the different models of drag forces.
Forcing function effects on unsteady aerodynamic gust response. I - Forcing functions
NASA Technical Reports Server (NTRS)
Henderson, Gregory H.; Fleeter, Sanford
1992-01-01
The paper investigates the fundamental gust modeling assumption on the basis of a series of experiments performed in the Purdue Annular Cascade Research Facility. The measured unsteady flow fields are compared to linear-theory gust requirements. The perforated plate forcing functions closely resemble linear-theory forcing functions, with the static pressure fluctuations small and the periodic velocity vectors parallel to the downstream mean-relative flow angle over the entire periodic cycle. The airfoil forcing functions exhibit characteristics far from linear-theory gusts, with the alignment of the velocity vectors and the static pressure fluctuation amplitudes dependent on the rotor-loading condition, rotor solidity, and the inlet mean-relative flow angle. It is shown that airfoil wakes, both compressor and turbine, cannot be modeled with the boundary conditions of current state-of-the-art linear unsteady aerodynamic theory.
New drag laws for flapping flight
NASA Astrophysics Data System (ADS)
Agre, Natalie; Zhang, Jun; Ristroph, Leif
2014-11-01
Classical aerodynamic theory predicts that a steadily-moving wing experiences fluid forces proportional to the square of its speed. For bird and insect flight, however, there is currently no model for how drag is affected by flapping motions of the wings. By considering simple wings driven to oscillate while progressing through the air, we discover that flapping significantly changes the magnitude of drag and fundamentally alters its scaling with speed. These measurements motivate a new aerodynamic force law that could help to understand the free-flight dynamics, control, and stability of insects and flapping-wing robots.
THE ROLE OF DRAG IN THE ENERGETICS OF STRONGLY FORCED EXOPLANET ATMOSPHERES
Rauscher, Emily; Menou, Kristen
2012-01-20
In contrast to the Earth, where frictional heating is typically negligible, we show that drag mechanisms could act as an important heat source in the strongly forced atmospheres of some exoplanets, with the potential to alter the circulation. We modify the standard formalism of the atmospheric energy cycle to explicitly track the loss of kinetic energy and the associated frictional (re)heating, for application to exoplanets such as the asymmetrically heated 'hot Jupiters' and gas giants on highly eccentric orbits. We establish that an understanding of the dominant drag mechanisms and their dependence on local atmospheric conditions is critical for accurate modeling, not just in their ability to limit wind speeds, but also because they could possibly change the energetics of the circulation enough to alter the nature of the flow. We discuss possible sources of drag and estimate the strength necessary to significantly influence the atmospheric energetics. As we show, the frictional heating depends on the magnitude of kinetic energy dissipation as well as its spatial variation, so that the more localized a drag mechanism is, the weaker it can be and still affect the circulation. We also use the derived formalism to estimate the rate of numerical loss of kinetic energy in a few previously published hot Jupiter models with and without magnetic drag and find it to be surprisingly large, at 5%-10% of the incident stellar irradiation.
Chaudhuri, M.; Khrapak, S. A.; Morfill, G. E.
2008-05-15
The ion drag force acting on a small absorbing grain has been calculated in highly collisional plasma with slowly drifting ions taking into account plasma production and loss processes in the vicinity of the grain. It is shown that the strength of the plasma production and loss mechanisms not only affects the magnitude of the ion drag force, but also determines the direction of the force. The parameter regimes for the ''positive'' and ''negative'' ion drag forces have been identified. In addition, the qualitative features of the electric potential distribution around the grain in isotropic conditions (in the absence of the ion drift) are investigated.
NASA Astrophysics Data System (ADS)
Paul, Maike; Thomas, Robert E.; Keevil, Gareth M.
2013-04-01
In lowland rivers, seasonal patterns of in-stream macrophyte growth and decay have significant implications for flood risk. For a given discharge, flood risk is increased when dense macrophyte canopies reduce flow areas, increase blockage ratios and alter reach-scale roughness values. These factors combine and can increase the flow depth. Conversely, submerged vegetation is exposed to drag forces exerted by the flow, which may be sufficient to damage limbs or dislodge plants. The classical drag equation suggests that the force exerted by fluid flows upon submerged vegetation is a function of the fluid properties, the projected area of the vegetation, and the square of the flow velocity. However, very few studies have simultaneously monitored all of these parameters, resulting in significant uncertainty in the estimation of the coefficient that relates these parameters to the drag force and also the related roughness parameters that control the flow depth for a given discharge. To our knowledge, this study presents the first concurrent field measurements of turbulent velocities, plant reconfigurations and drag forces acting on Ranunculus penicillatus ssp. pseudofluitans (Syme) S.D.Webster. Measurements were undertaken in an artificially straightened reach of the chalk-bed River Wylye, near Longbridge Deverill, Wiltshire, UK. The reach is 5.7 m wide and during measurements there was a mean flow depth of 0.28 m and an average discharge of 0.28 m³s-1. The reach is cleared of vegetation up to three times a year for flood defence purposes, but Ranunculus p. grows back within several weeks. Measurements were carried out after re-growth, when plants were fully developed with a mean length of 0.75 m and on average 6 nodes along the stem. The distances between the nodes increased from the base towards the tip and each node produced a capillary leaf, sometimes in conjunction with a branch. Floating leaves and flowers were not present. Plants were attached to a custom
Bishop, Kristin L
2007-08-01
Gliding has often been discussed in the literature as a possible precursor to powered flight in vertebrates, but few studies exist on the mechanics of gliding in living animals. In this study I analyzed the 3D kinematics of sugar gliders (Petaurus breviceps) during short glides in an enclosed space. Short segments of the glide were captured on video, and the positions of marked anatomical landmarks were used to compute linear distances and angles, as well as whole body velocities and accelerations. From the whole body accelerations I estimated the aerodynamic forces generated by the animals. I computed the correlations between movements of the limbs and body rotations to examine the control of orientation during flight. Finally, I compared these results to those of my earlier study on the similarly sized and distantly related southern flying squirrel (Glaucomys volans). The sugar gliders in this study accelerated downward slightly (1.0+/-0.5 m s(-2)), and also accelerated forward (2.1+/-0.6 m s(-2)) in all but one trial, indicating that the body weight was not fully supported by aerodynamic forces and that some of the lift produced forward acceleration rather than just balancing body weight. The gliders used high angles of attack (44.15+/-3.12 degrees ), far higher than the angles at which airplane wings would stall, yet generated higher lift coefficients (1.48+/-0.18) than would be expected for a stalled wing. Movements of the limbs were strongly correlated with body rotations, suggesting that sugar gliders make extensive use of limb movements to control their orientation during gliding flight. In addition, among individuals, different limb movements were associated with a given body rotation, suggesting that individual variation exists in the control of body rotations. Under similar conditions, flying squirrels generated higher lift coefficients and lower drag coefficients than sugar gliders, yet had only marginally shallower glides. Flying squirrels have a
Wind Tunnel Testing on Crosswind Aerodynamic Forces Acting on Railway Vehicles
NASA Astrophysics Data System (ADS)
Kwon, Hyeok-Bin; Nam, Seong-Won; You, Won-Hee
This study is devoted to measure the aerodynamic forces acting on two railway trains, one of which is a high-speed train at 300km/h maximum operation speed, and the other is a conventional train at the operating speed 100km/h. The three-dimensional train shapes have been modeled as detailed as possible including the inter-car, the upper cavity for pantograph, and the bogie systems. The aerodynamic forces on each vehicle of the trains have been measured in the subsonic wind tunnel with 4m×3m test section of Korea Aerospace Research Institute at Daejeon, Korea. The aerodynamic forces and moments of the train models have been plotted for various yaw angles and the characteristics of the aerodynamic coefficients has been discussed relating to the experimental conditions.
NASA Astrophysics Data System (ADS)
Pierre, Thiery
2015-11-01
A new plasma device named M-DBD (Microwave Dielectric Barrier Discharge) is used for controlling the boundary layer in order to reduce the drag force. A compact resonant UHF structure comprising a resonant element in the form of a quarter-wave antenna creates a mini-plasma insulated from the UHF electrodes by mica sheets. Additional electrodes induce an electric field in the plasma and transiently move the ions of the plasma. The high collision rate with the neutral molecules induce the global transient flow of the neutral gas. The temporal variation of the applied electric field is chosen in order to obtain a modification of the local boundary layer. First tests using an array of M-DBD plasma actuators are underway (see Patent ref. WO 2014111469 A1).
Effect of a drag force due to absorption of solar radiation on solar sail orbital dynamics
NASA Astrophysics Data System (ADS)
Kezerashvili, Roman Ya.; Vázquez-Poritz, Justin F.
2013-03-01
While solar electromagnetic radiation can be used to propel a solar sail, it is shown that the Poynting-Robertson effect related to the absorbed portion of the radiation leads to a drag force in the transversal direction. The Poynting-Robertson effect is considered for escape trajectories, Heliocentric bound orbits and non-Keplerian bound orbits. For escape trajectories, this drag force diminishes the cruising velocity, which has a cumulative effect on the Heliocentric distance. For Heliocentric and non-Keplerian bound orbits, the Poynting-Robertson effect decreases its orbital speed, thereby causing it to slowly spiral towards the Sun. Since the Poynting-Robertson effect is due to the absorbed portion of the electromagnetic radiation, degradation of a solar sail implies that this effect becomes enhanced during a mission.
Aerodynamic forces induced by controlled transitory flow on a body of revolution
NASA Astrophysics Data System (ADS)
Rinehart, Christopher S.
The aerodynamic forces and moments on an axisymmetric body of revolution are controlled in a low-speed wind tunnel by induced local flow attachment. Control is effected by an array of aft-facing synthetic jets emanating from narrow, azimuthally segmented slots embedded within an axisymmetric backward facing step. The actuation results in a localized, segmented vectoring of the separated base flow along a rear Coanda surface and induced asymmetric aerodynamic forces and moments. The observed effects are investigated in both quasi-steady and transient states, with emphasis on parametric dependence. It is shown that the magnitude of the effected forces can be substantially increased by slight variations of the Coanda surface geometry. Force and velocity measurements are used to elucidate the mechanisms by which the synthetic jets produce asymmetric aerodynamic forces and moments, demonstrating a novel method to steer axisymmetric bodies during flight.
Binaries Traveling through a Gaseous Medium: Dynamical Drag Forces and Internal Torques
NASA Astrophysics Data System (ADS)
Sánchez-Salcedo, F. J.; Chametla, Raul O.
2014-10-01
Using time-dependent linear theory, we investigate the morphology of the gravitational wake induced by a binary, whose center of mass moves at velocity {\\boldsymbol {V}}_cm against a uniform background of gas. For simplicity, we assume that the components of the binary are on circular orbits about their common center of mass. The consequences of dynamical friction is twofold. First, gas dynamical friction may drag the center of mass of the binary and cause the binary to migrate. Second, drag forces also induce a braking torque, which causes the orbits of the components of the binary to shrink. We compute the drag forces acting on one component of the binary due to the gravitational interaction with its own wake. We show that the dynamical friction force responsible for decelerating the center of mass of the binary is smaller than it is in the point-mass case because of the loss of gravitational focusing. We show that the braking internal torque depends on the Mach numbers of each binary component about their center of mass, and also on the Mach number of the center of mass of the binary. In general, the internal torque decreases with increasing the velocity of the binary relative to the ambient gas cloud. However, this is not always the case. We also mention the relevance of our results to the period distribution of binaries.
Turbulence model choice for the calculation of drag forces when using the CFD method.
Zaïdi, H; Fohanno, S; Taïar, R; Polidori, G
2010-02-10
The aim of this work is to specify which model of turbulence is the most adapted in order to predict the drag forces that a swimmer encounters during his movement in the fluid environment. For this, a Computational Fluid Dynamics (CFD) analysis has been undertaken with a commercial CFD code (Fluent). The problem was modelled as 3D and in steady hydrodynamic state. The 3D geometry of the swimmer was created by means of a complete laser scanning of the swimmer's body contour. Two turbulence models were tested, namely the standard k-epsilon model with a specific treatment of the fluid flow area near the swimmer's body contour, and the standard k-omega model. The comparison of numerical results with experimental measurements of drag forces shows that the standard k-omega model accurately predicts the drag forces while the standard k-epsilon model underestimates their values. The standard k-omega model also enabled to capture the vortex structures developing at the swimmer's back and buttocks in underwater swimming; the same vortices had been visualized by flow visualization experiments carried out at the INSEP (National Institute for Sport and Physical Education in Paris) with the French national swimming team. PMID:19889420
Binaries traveling through a gaseous medium: dynamical drag forces and internal torques
Sánchez-Salcedo, F. J.; Chametla, Raul O.
2014-10-20
Using time-dependent linear theory, we investigate the morphology of the gravitational wake induced by a binary, whose center of mass moves at velocity V{sub cm} against a uniform background of gas. For simplicity, we assume that the components of the binary are on circular orbits about their common center of mass. The consequences of dynamical friction is twofold. First, gas dynamical friction may drag the center of mass of the binary and cause the binary to migrate. Second, drag forces also induce a braking torque, which causes the orbits of the components of the binary to shrink. We compute the drag forces acting on one component of the binary due to the gravitational interaction with its own wake. We show that the dynamical friction force responsible for decelerating the center of mass of the binary is smaller than it is in the point-mass case because of the loss of gravitational focusing. We show that the braking internal torque depends on the Mach numbers of each binary component about their center of mass, and also on the Mach number of the center of mass of the binary. In general, the internal torque decreases with increasing the velocity of the binary relative to the ambient gas cloud. However, this is not always the case. We also mention the relevance of our results to the period distribution of binaries.
Balash, Cheslav; Sterling, David; Binns, Jonathan; Thomas, Giles; Bose, Neil
2015-01-01
For prawn trawling systems, drag reduction is a high priority as the trawling process is energy intensive. Large benefits have occurred through the use of multiple-net rigs and thin twine in the netting. An additional positive effect of these successful twine-area reduction strategies is the reduced amount of otter board area required to spread the trawl systems, which leads to further drag reduction. The present work investigated the potential of redirecting the drag-strain within a prawn trawl away from the wings and the otter boards to the centre line of the trawl, where top and bottom tongues have been installed, with an aim to minimise the loading/size of the otter boards required to spread the trawl. In the system containing the new 'W' trawl, the drag redirected to the centre-line tongues is transferred forward through a connected sled and towing wires to the trawler. To establish the extent of drag redirection to the centre-line tongues and the relative drag benefits of the new trawl system, conventional and 'W' trawls of 3.65 m headline length were tested firstly over a range of spread ratios in the flume tank, and subsequently at optimum spread ratio in the field. The developed 'W' trawl effectively directed 64% of netting-drag off the wings and onto the centre tongues, which resulted in drag savings in the field of ∼20% for the associated 'W' trawl/otter-board/sled system compared to the traditional trawl/otter-board arrangement in a single trawl or twin rig configuration. Furthermore, based on previously published data, the new trawl when used in a twin rig system is expected to provide approximately 12% drag reduction compared to quad rig. The twin 'W' trawl system also has benefits over quad rig in that a reduced number of cod-end/By-catch Reduction Device units need to be installed and attended each tow. PMID:25751251
Force and flow at the onset of drag in plowed granular media.
Gravish, Nick; Umbanhowar, Paul B; Goldman, Daniel I
2014-04-01
We study the transient drag force FD on a localized intruder in a granular medium composed of spherical glass particles. A flat plate is translated horizontally from rest through the granular medium to observe how FD varies as a function of the medium's initial volume fraction, ϕ. The force response of the granular material differs above and below the granular critical state, ϕc, the volume fraction which corresponds to the onset of grain dilatancy. For ϕ<ϕc FD increases monotonically with displacement and is independent of drag velocity for the range of velocities examined (<10 cm/s). For ϕ>ϕc, FD rapidly rises to a maximum and then decreases over further displacement. The maximum force for ϕ>ϕc increases with increasing drag velocity. In quasi-two-dimensional drag experiments, we use granular particle image velocimetry (PIV) to measure time resolved strain fields associated with the horizontal motion of a plate started from rest. PIV experiments show that the maxima in FD for ϕ>ϕc are associated with maxima in the spatially averaged shear strain field. For ϕ>ϕc the shear strain occurs in a narrow region in front of the plate, a shear band. For ϕ<ϕc the shear strain is not localized, the shear band fluctuates in space and time, and the average shear increases monotonically with displacement. Laser speckle measurements made at the granular surface ahead of the plate reveal that for ϕ<ϕc particles are in motion far from the intruder and shearing region. For ϕ>ϕc, surface particles move only during the formation of the shear band, coincident with the maxima in FD, after which the particles remain immobile until the sheared region reaches the measurement region. PMID:24827236
Performance losses of drag-reducing spanwise forcing at moderate values of the Reynolds number
NASA Astrophysics Data System (ADS)
Gatti, Davide; Quadrio, Maurizio
2013-12-01
A fundamental problem in the field of turbulent skin-friction drag reduction is to determine the performance of the available control techniques at high values of the Reynolds number Re. We consider active, predetermined strategies based on spanwise forcing (oscillating wall and streamwise-traveling waves applied to a plane channel flow), and explore via Direct Numerical Simulations (DNS) up to Reτ = 2100 the rate at which their performance deteriorates as Re is increased. To be able to carry out a comprehensive parameter study, we limit the computational cost of the simulations by adjusting the size of the computational domain in the homogeneous directions, compromising between faster computations and the increased need of time-averaging the fluctuating space-mean wall shear-stress. Our results, corroborated by a few full-scale DNS, suggest a scenario where drag reduction degrades with Re at a rate that varies according to the parameters of the wall forcing. In agreement with already available information, keeping them at their low-Re optimal value produces a relatively quick decrease of drag reduction. However, at higher Re the optimal parameters shift towards other regions of the parameter space, and these regions turn out to be much less sensitive to Re. Once this shift is accounted for, drag reduction decreases with Re at a markedly slower rate. If the slightly favorable trend of the energy required to create the forcing is considered, a chance emerges for positive net energy savings also at large values of the Reynolds number.
THE GRAVITATIONAL DRAG FORCE ON AN EXTENDED OBJECT MOVING IN A GAS
Bernal, Cristian G.; Sánchez-Salcedo, F. J.
2013-09-20
Using axisymmetrical numerical simulations, we revisit the gravitational drag felt by a gravitational Plummer sphere with mass M and core radius R{sub s} moving at constant velocity V{sub 0} through a background homogeneous medium of adiabatic gas. Since the potential is non-diverging, there is no gas removal due to accretion. When R{sub s} is larger than the Bondi radius R{sub B} , the perturbation is linear at every point and the drag force is well fitted by the time-dependent Ostriker's formula with r{sub min} = 2.25R{sub s} , where r{sub min} is the minimum impact parameter in the Coulomb logarithm. In the deep nonlinear supersonic regime (R{sub s} << R{sub B} ), the minimum radius is no longer related to R{sub s} but to R{sub B} . We find r{sub min}=3.3M{sup -2.5}R{sub B} for Mach numbers of the perturber between 1.5 and 4, although r{sub min}= 2M{sup -2}R{sub B}=2GM/V{sup 2}{sub 0} also provides a good fit at M>2. As a consequence, the drag force does not depend sensitively on the nonlinearity parameter A, defined as R{sub B} /R{sub s} , for A values larger than a certain critical value A{sub cr}. We show that our generalized Ostriker's formula for the drag force is more accurate than the formula suggested by Kim and Kim.
Force and flow at the onset of drag in plowed granular media
NASA Astrophysics Data System (ADS)
Gravish, Nick; Umbanhowar, Paul B.; Goldman, Daniel I.
2014-04-01
We study the transient drag force FD on a localized intruder in a granular medium composed of spherical glass particles. A flat plate is translated horizontally from rest through the granular medium to observe how FD varies as a function of the medium's initial volume fraction, ϕ. The force response of the granular material differs above and below the granular critical state, ϕc, the volume fraction which corresponds to the onset of grain dilatancy. For ϕ <ϕc FD increases monotonically with displacement and is independent of drag velocity for the range of velocities examined (<10 cm/s). For ϕ >ϕc, FD rapidly rises to a maximum and then decreases over further displacement. The maximum force for ϕ >ϕc increases with increasing drag velocity. In quasi-two-dimensional drag experiments, we use granular particle image velocimetry (PIV) to measure time resolved strain fields associated with the horizontal motion of a plate started from rest. PIV experiments show that the maxima in FD for ϕ >ϕc are associated with maxima in the spatially averaged shear strain field. For ϕ >ϕc the shear strain occurs in a narrow region in front of the plate, a shear band. For ϕ <ϕc the shear strain is not localized, the shear band fluctuates in space and time, and the average shear increases monotonically with displacement. Laser speckle measurements made at the granular surface ahead of the plate reveal that for ϕ <ϕc particles are in motion far from the intruder and shearing region. For ϕ >ϕc, surface particles move only during the formation of the shear band, coincident with the maxima in FD, after which the particles remain immobile until the sheared region reaches the measurement region.
Wing and body motion and aerodynamic and leg forces during take-off in droneflies.
Chen, Mao Wei; Zhang, Yan Lai; Sun, Mao
2013-12-01
Here, we present a detailed analysis of the take-off mechanics in droneflies performing voluntary take-offs. Wing and body kinematics of the insects during take-off were measured using high-speed video techniques. Based on the measured data, the inertia force acting on the insect was computed and the aerodynamic force of the wings was calculated by the method of computational fluid dynamics. Subtracting the aerodynamic force and the weight from the inertia force gave the leg force. In take-off, a dronefly increases its stroke amplitude gradually in the first 10-14 wingbeats and becomes airborne at about the 12th wingbeat. The aerodynamic force increases monotonously from zero to a value a little larger than its weight, and the leg force decreases monotonously from a value equal to its weight to zero, showing that the droneflies do not jump and only use aerodynamic force of flapping wings to lift themselves into the air. Compared with take-offs in insects in previous studies, in which a very large force (5-10 times of the weight) generated either by jumping legs (locusts, milkweed bugs and fruit flies) or by the 'fling' mechanism of the wing pair (butterflies) is used in a short time, the take-off in the droneflies is relatively slow but smoother. PMID:24132205
Wing and body motion and aerodynamic and leg forces during take-off in droneflies
Chen, Mao Wei; Zhang, Yan Lai; Sun, Mao
2013-01-01
Here, we present a detailed analysis of the take-off mechanics in droneflies performing voluntary take-offs. Wing and body kinematics of the insects during take-off were measured using high-speed video techniques. Based on the measured data, the inertia force acting on the insect was computed and the aerodynamic force of the wings was calculated by the method of computational fluid dynamics. Subtracting the aerodynamic force and the weight from the inertia force gave the leg force. In take-off, a dronefly increases its stroke amplitude gradually in the first 10–14 wingbeats and becomes airborne at about the 12th wingbeat. The aerodynamic force increases monotonously from zero to a value a little larger than its weight, and the leg force decreases monotonously from a value equal to its weight to zero, showing that the droneflies do not jump and only use aerodynamic force of flapping wings to lift themselves into the air. Compared with take-offs in insects in previous studies, in which a very large force (5–10 times of the weight) generated either by jumping legs (locusts, milkweed bugs and fruit flies) or by the ‘fling’ mechanism of the wing pair (butterflies) is used in a short time, the take-off in the droneflies is relatively slow but smoother. PMID:24132205
Kinetic approach for the ion drag force in a collisional plasma
Ivlev, A.V.; Zhdanov, S.K.; Khrapak, S.A.; Morfill, G.E.
2005-01-01
The linear kinetic approach to calculate the ion drag force in a collisional plasma is generalized. The model collision integral (for ion-neutral collisions) is discussed and employed to calculate the plasma response for arbitrary velocity of the plasma flow and arbitrary frequency of the collisions. The derived plasma response is used to calculate the self-consistent force on the test charged particle. The obtained results are compared to those of the traditional pair collision approach, and the importance of the self-consistent kinetic consideration is highlighted. In conclusion, the applicability of the proposed approach is discussed.
NASA Astrophysics Data System (ADS)
Wang, Z. Jane; Russell, David
2007-10-01
Dragonflies are four-winged insects that have the ability to control aerodynamic performance by modulating the phase lag (ϕ) between forewings and hindwings. We film the wing motion of a tethered dragonfly and compute the aerodynamic force and power as a function of the phase. We find that the out-of-phase motion as seen in steady hovering uses nearly minimal power to generate the required force to balance the weight, and the in-phase motion seen in takeoffs provides an additional force to accelerate. We explain the main hydrodynamic interaction that causes this phase dependence.
Liquid-Infused Surfaces with Trapped Air (LISTA) for Drag Force Reduction.
Hemeda, A A; Tafreshi, H Vahedi
2016-03-29
Superhydrophobic (SHP) surfaces are known for their drag-reducing attributes thanks to their ability to trap air in their surface pores and thereby reduce the contact between water and the frictional solid area. SHP surfaces are prone to failure under elevated pressures or because of air-layer dissolution into the surrounding water. Slippery liquid-infused porous surfaces (SLIPS) or liquid-infused surfaces (LIS) in which the trapped air is replaced with a lubricant have been proposed in the literature as a way of eliminating the air dissolution problem as well as improving the surface stability under pressure. While an LIS surface has been shown to reduce drag for flow of water-glycerol mixture (ref 18), no significant drag reduction has yet been reported for the flow of water (a lower viscosity fluid) over LIS. In this concern, we have designed a new surface in which a layer of air is trapped underneath the infused lubricant to reduce the frictional forces preventing the LIS to provide drag reduction for water or any fluid with a viscosity less than that of the lubricant. Drag reduction performance of such surfaces, referred to here as liquid-infused surfaces with trapped air (LISTA), is predicted by solving the biharmonic equation for the water-oil-air three-phase system in transverse grooves with enhanced meniscus stability thanks to double-reentry designs. For the arbitrary dimensions considered in our proof-of-concept study, LISTA designs showed 20-37% advantage over their LIS counterparts. PMID:26977775
NASA Astrophysics Data System (ADS)
Dubov, Alexander L.; Schmieschek, Sebastian; Asmolov, Evgeny S.; Harting, Jens; Vinogradova, Olga I.
2014-01-01
By means of lattice-Boltzmann simulations the drag force on a sphere of radius R approaching a superhydrophobic striped wall has been investigated as a function of arbitrary separation h. Superhydrophobic (perfect-slip vs. no-slip) stripes are characterized by a texture period L and a fraction of the gas area ϕ. For very large values of h/R, we recover the macroscopic formulae for a sphere moving towards a hydrophilic no-slip plane. For h/R = O(1), the drag force is smaller than predicted by classical theories for hydrophilic no-slip surfaces, but larger than expected for a sphere interacting with a uniform perfectly slipping wall. At a thinner gap, h ≪ R the force reduction compared to a classical result becomes more pronounced, and is maximized by increasing ϕ. In the limit of very small separations, our simulation data are in quantitative agreement with an asymptotic equation, which relates a correction to a force for superhydrophobic slip to texture parameters. In addition, we examine the flow and pressure field and observe their oscillatory character in the transverse direction in the vicinity of the wall, which reflects the influence of the heterogeneity and anisotropy of the striped texture. Finally, we investigate the lateral force on the sphere, which is detectable in case of very small separations and is maximized by stripes with ϕ = 0.5.
NASA Astrophysics Data System (ADS)
Guo, Lei; Gao, Han; Yu, Jin-tao; Zhang, Zong-liang; Guo, Zhan-cheng
2015-01-01
The fixed-gas drag force from a model calculation method that stabilizes the agitation capabilities of different gas ratios was used to explore the influence of temperature and hydrogen concentration on fluidizing duration, metallization ratio, utilization rate of reduction gas, and sticking behavior. Different hydrogen concentrations from 5vol% to 100vol% at 1073 and 1273 K were used while the drag force with the flow of N2 and H2 (N2: 2 L·min-1; H2: 2 L·min-1) at 1073 K was chosen as the standard drag force. The metallization ratio, mean reduction rate, and utilization rate of reduction gas were observed to generally increase with increasing hydrogen concentration. Faster reduction rates and higher metallization ratios were obtained when the reduction temperature decreased from 1273 to 1073 K. A numerical relation among particle diameter, particle drag force, and fluidization state was plotted in a diagram by this model.
NASA Astrophysics Data System (ADS)
Suzuki, Masahiro; Nakade, Koji
A basic study of flow controls using air blowing was conducted to reduce unsteady aerodynamic force acting on trains running in tunnels. An air blowing device is installed around a model car in a wind tunnel. Steady and periodic blowings are examined utilizing electromagnetic valves. Pressure fluctuations are measured and the aerodynamic force acting on the car is estimated. The results are as follows: a) The air blowing allows reducing the unsteady aerodynamic force. b) It is effective to blow air horizontally at the lower side of the car facing the tunnel wall. c) The reduction rate of the unsteady aerodynamic force relates to the rate of momentum of the blowing to that of the uniform flow. d) The periodic blowing with the same frequency as the unsteady aerodynamic force reduces the aerodynamic force in a manner similar to the steady blowing.
Comparison of buoyancy, passive and net active drag forces between Fastskin and standard swimsuits.
Benjanuvatra, N; Dawson, G; Blanksby, B A; Elliott, B C
2002-06-01
A cross-sectional comparison between the buoyancy, passive and net active drag force characteristics of full-length, Fastskin swimsuits with that of standard swimsuits was completed with nine Open National level swimmers (5 males and 4 females). Subjects were weighed in a hydrostatic tank and then towed via a mechanical winch on the surface and 0.4 m deep at 1.6, 2.2 and 2.8 m/s. The subjects performed a prone streamlined glide and maximum effort flutter kick at each towing velocity and depth. Hydrostatic weight differences between swimsuit types were not significant (p> 0.05. Fastskin passive drag values were significantly less than normal swimsuits during surface towing at 1.6 and 2.8 m/s: and at 0.4 m deep towing at 1.6, 2.2 and 2.8 m/s. Net active drag force values also were lower for the Fastskin suits when compared with those of normal swimsuits and a significant difference existed for surface towing at all three velocities of 1.6, 2.2 and 2.8 m/s. The full-length, Fastskin swimsuits created less total hydrodynamic resistance than normal swimsuits while providing no additional buoyancy benefits. PMID:12188083
Modal forced vibration analysis of aerodynamically excited turbosystems
NASA Technical Reports Server (NTRS)
Elchuri, V.
1985-01-01
Theoretical aspects of a new capability to determine the vibratory response of turbosystems subjected to aerodynamic excitation are presented. Turbosystems such as advanced turbopropellers with highly swept blades, and axial-flow compressors and turbines can be analyzed using this capability. The capability has been developed and implemented in the April 1984 release of the general purpose finite element program NASTRAN. The dynamic response problem is addressed in terms of the normal modal coordinates of these tuned rotating cyclic structures. Both rigid and flexible hubs/disks are considered. Coriolis and centripetal accelerations, as well as differential stiffness effects are included. Generally non-uniform steady inflow fields and uniform flow fields arbitrarily inclined at small angles with respect to the axis of rotation of the turbosystem are considered sources of aerodynamic excitation. The spatial non-uniformities are considered to be small deviations from a principally uniform inflow. Subsonic and supersonic relative inflows are addressed, with provision for linearly interpolating transonic airloads.
Modeling of Aerodynamic Force Acting in Tunnel for Analysis of Riding Comfort in a Train
NASA Astrophysics Data System (ADS)
Kikko, Satoshi; Tanifuji, Katsuya; Sakanoue, Kei; Nanba, Kouichiro
In this paper, we aimed to model the aerodynamic force that acts on a train running at high speed in a tunnel. An analytical model of the aerodynamic force is developed from pressure data measured on car-body sides of a test train running at the maximum revenue operation speed. The simulation of an 8-car train running while being subjected to the modeled aerodynamic force gives the following results. The simulated car-body vibration corresponds to the actual vibration both qualitatively and quantitatively for the cars at the rear of the train. The separation of the airflow at the tail-end of the train increases the yawing vibration of the tail-end car while it has little effect on the car-body vibration of the adjoining car. Also, the effect of the moving velocity of the aerodynamic force on the car-body vibration is clarified that the simulation under the assumption of a stationary aerodynamic force can markedly increase the car-body vibration.
NASA Technical Reports Server (NTRS)
Fralick, G. C.
1982-01-01
It is shown that a conventional electronic frequency compensator does not provide adequate compensation near the resonant frequency of a lightly damped second order system, such as the drag force anemometer. The reason for this is discussed, and a simple circuit modification is presented which overcomes the difficulty. The improvement is shown in theoretical frequency response curves as well as in the experimental results from some typical drag force anemometers.
NASA Astrophysics Data System (ADS)
Varshney, Kapil; Chang, Song; Wang, Z. Jane
2013-05-01
Falling parallelograms exhibit coupled motion of autogyration and tumbling, similar to the motion of falling tulip seeds, unlike maple seeds which autogyrate but do not tumble, or rectangular cards which tumble but do not gyrate. This coupled tumbling and autogyrating motion are robust, when card parameters, such as aspect ratio, internal angle, and mass density, are varied. We measure the three-dimensional (3D) falling kinematics of the parallelograms and quantify their descending speed, azimuthal rotation, tumbling rotation, and cone angle in each falling. The cone angle is insensitive to the variation of the card parameters, and the card tumbling axis does not overlap with but is close to the diagonal axis. In addition to this connection to the dynamics of falling seeds, these trajectories provide an ideal set of data to analyze 3D aerodynamic force and torque at an intermediate range of Reynolds numbers, and the results will be useful for constructing 3D aerodynamic force and torque models. Tracking these free falling trajectories gives us a nonintrusive method for deducing instantaneous aerodynamic forces. We determine the 3D aerodynamic forces and torques based on Newton-Euler equations. The dynamical analysis reveals that, although the angle of attack changes dramatically during tumbling, the aerodynamic forces have a weak dependence on the angle of attack. The aerodynamic lift is dominated by the coupling of translational and rotational velocities. The aerodynamic torque has an unexpectedly large component perpendicular to the card. The analysis of the Euler equation suggests that this large torque is related to the deviation of the tumbling axis from the principle axis of the card.
Optimal flapping wing for maximum vertical aerodynamic force in hover: twisted or flat?
Phan, Hoang Vu; Truong, Quang Tri; Au, Thi Kim Loan; Park, Hoon Cheol
2016-01-01
This work presents a parametric study, using the unsteady blade element theory, to investigate the role of twist in a hovering flapping wing. For the investigation, a flapping-wing system was developed to create a wing motion of large flapping amplitude. Three-dimensional kinematics of a passively twisted wing, which is capable of creating a linearly variable geometric angle of attack (AoA) along the wingspan, was measured during the flapping motion and used for the analysis. Several negative twist or wash-out configurations with different values of twist angle, which is defined as the difference in the average geometric AoAs at the wing root and the wing tip, were obtained from the measured wing kinematics through linear interpolation and extrapolation. The aerodynamic force generation and aerodynamic power consumption of these twisted wings were obtained and compared with those of flat wings. For the same aerodynamic power consumption, the vertical aerodynamic forces produced by the negatively twisted wings are approximately 10%-20% less than those produced by the flat wings. However, these twisted wings require approximately 1%-6% more power than flat wings to produce the same vertical force. In addition, the maximum-force-producing twisted wing, which was found to be the positive twist or wash-in configuration, was used for comparison with the maximum-force-producing flat wing. The results revealed that the vertical aerodynamic force and aerodynamic power consumption of the two types of wings are almost identical for the hovering condition. The power loading of the positively twisted wing is only approximately 2% higher than that of the maximum-force-producing flat wing. Thus, the flat wing with proper wing kinematics (or wing rotation) can be regarded as a simple and efficient candidate for the development of hovering flapping-wing micro air vehicle. PMID:27387833
Analysis of the aerodynamic force in an eye-stabilized flapping flyer.
Su, Jian-Yuan; Yang, Jing-Tang
2013-12-01
Experimental methods and related theories to evaluate the lift force for a flyer are established, but one can traditionally acquire only the magnitude of that lift. We here proffer an analysis based on kinematic theory and experimental visualization of the flow to complete a treatment of the aerodynamic force affecting a hovering flyer that generates a lift force approximately equal to its weight, and remains nearly stationary in midair; the center and direction of the aerodynamic force are accordingly determined with some assumptions made. The principal condition to resolve the problem is the stabilization of the vision of a flyer, which is inspired by a hovering passerine that experiences a substantial upward swing during downstroke periods while its eye remains stabilized. Viewing the aerodynamic force with a bird's eye, we find that the center and direction of this aerodynamic force vary continuously with respect to the lift force. Our results provide practical guidance for engineers to enhance the visual stability of surveillance cameras incorporated in micro aerial vehicles. PMID:24200672
Transitory Aerodynamic Forces on a Body of Revolution using Synthetic Jet Actuation
NASA Astrophysics Data System (ADS)
Rinehart, Christopher; McMichael, James; Glezer, Ari
2002-11-01
The aerodynamic forces and moments on axisymmetric bodies at subsonic speeds are controlled by exploiting local flow attachment using fluidic (synthetic jet) actuation and thereby altering the apparent aerodynamic shape of the surface. Control is effected upstream of the base of the body by an azimuthal array of individually-controlled, aft-facing synthetic jets emanating along an azimuthal Coanda surface. Actuation produces asymmetric aerodynamic forces and moments, with ratios of lift to average jet momentum approaching values typical of conventional jet-based circulation control on two-dimensional airfoils. Momentary forces are achieved using transient (pulsed) actuation and are accompanied by the formation and shedding of vorticity concentrations as a precursor to the turning of the outer flow into the wake region.
NASA Technical Reports Server (NTRS)
Cole, Jennifer Hansen
2010-01-01
This slide presentation reviews some of the basic principles of aerodynamics. Included in the presentation are: a few demonstrations of the principles, an explanation of the concepts of lift, drag, thrust and weight, a description of Bernoulli's principle, the concept of the airfoil (i.e., the shape of the wing) and how that effects lift, and the method of controlling an aircraft by manipulating the four forces using control surfaces.
NASA Astrophysics Data System (ADS)
Villegas Vaquero, Arturo
Aerodynamic unsteady forces in stationary and rotating wings are analyzed in this dissertation by using a combination of time-resolved particle image velocimetry (TR-PIV) and proper orthogonal decomposition (POD) techniques. Recent progress in experimental measurements has demonstrated the use of TR-PIV to calculate forces by applying the integral conservation of momentum equation in its different forms. However, a more accurate and robust method is needed for unsteady forces calculations. With this in mind, a modified pressure Poisson method is developed and applied in this work, showing its superior behavior compared to other methodologies described in the past. The independence of the calculated forces shows the robustness and stability of the method. Whereas force calculations have been recently considered, the role of flow structures in force fluctuations has not been revealed yet and it is the main focus of this study. To elucidate these relations, a hybrid PIV-POD analysis is applied to reconstruct the velocity field from the most energetic modes of the flow. A model describing the vortex-force relations is proposed in terms of lift and drag variations during the vortex shedding process. A spectral analysis of the calculated forces suggests symmetric periodic lift, drag and circulation variations at the shedding frequency. Moreover, lift, drag and circulation signals are in phase, which supports lift-circulation proportionality. However, non-symmetric drag fluctuations are found at double the shedding frequency within a shedding cycle. For instance, when a positive or negative circulation vortex detaches, different values in the maximum and minimum drag are obtained. The data and physical relations obtained in this work such as main frequencies, vortex-force fluctuations and behavior of reduced-order models can aid in the development of CFD applications at low Re. The methodology described can be applied to any moving or stationary wing at different Reynolds
NASA Astrophysics Data System (ADS)
Kim, B.; Williams, D. R.
1998-11-01
The instantaneous pressure distribution was measured around the azimuth of a circular cylinder undergoing forced oscillations. The forcing direction was either in-line or cross-flow to produce symmetric or antisymmetric disturbances, respectively. The fluctuating lift and drag coefficients were computed from the pressure distributions. Combination modes appear in the spectrum of the surface pressure signals when the forcing frequency is different from the von Karman vortex shedding frequency, fo. The spatial symmetry of the sum and difference modes depends on the direction of the cylinder oscillation, and is predictable with a simple set of symmetry relations representative of quadratic nonlinear interaction. As a result, cross-flow oscillations channel energy into the fluctuating drag component through the combination modes, while in-line oscillations affect the fluctuating lift. The second harmonic (3 fo) commonly seen in flow-induced vibrations is the result of the nonlinear interaction between the fundamental and its first harmonic. By the symmetry relations, the 3 fo mode necessarily appears in the fluctuating lift spectrum.
Drag forces on aquatic plants in nonlinear random waves plus current
NASA Astrophysics Data System (ADS)
Henry, Pierre-Yves; Myrhaug, Dag; Aberle, Jochen
2015-11-01
Plant-flow interactions are characterised by an assemblage of processes acting at different temporal and spatial scales. In order to mathematically characterise these interactions, such processes have to be parameterised given some simplifications. Typically, drag coefficients are derived from experiments to characterise the plant reconfiguration and wave energy dissipation processes. By reviewing the different plant drag coefficients CD valid in oscillatory flows, this study first highlights the lack of normalisation of the different existing CD formulations and identifies possibilities for a standardisation of the formulations for oscillatory and steady flows. Then, by taking into account the wave crest height distribution of a sea state condition, this study further develops a stochastic method to compute the expected wave induced forces on a plant in linear/nonlinear random waves plus current based on two different CD formulations for waves alone and waves plus current. This method improves the characterisation of the stochastic plant-flow interactions by allowing the calculation of expected values under different random wave plus currents conditions. Results are compared to a classic deterministic approach and some differences are identified, calling for further investigations against experimental datasets. Based on the appropriate CD formulations, this study finally revealed that wave nonlinearities have a significant effect on expected wave forces for a higher wave activity, and that in presence of an increasing current, the effect of wave nonlinearities decreases while the expected wave forces increase.
Vortex motion of dust particles due to non-conservative ion drag force in a plasma
NASA Astrophysics Data System (ADS)
Chai, Kil-Byoung; Bellan, Paul M.
2016-02-01
Vortex motion of the dust in a dusty plasma is shown to result because non-parallelism of the ion density gradient and the gradient of the magnitude of the ion ambipolar velocity cause the ion drag force on dust grains to be non-conservative. Dust grain poloidal vortices consistent with the model predictions are experimentally observed, and the vortices change character with imposed changes in the ion temperature profile as predicted. For a certain ion temperature profile, two adjacent co-rotating poloidal vortices have a well-defined X-point analogous to the X-point in magnetic reconnection.
Physically-based modeling of drag force caused by natural woody vegetation
NASA Astrophysics Data System (ADS)
Järvelä, J.; Aberle, J.
2014-12-01
Riparian areas and floodplains are characterized by woody vegetation, which is an essential feature to be accounted for in many hydro-environmental models. For applications including flood protection, river restoration and modelling of sediment processes, there is a need to improve the reliability of flow resistance estimates. Conventional methods such as the use of lumped resistance coefficients or simplistic cylinder-based drag force equations can result in significant errors, as these methods do not adequately address the effect of foliage and reconfiguration of flexible plant parts under flow action. To tackle the problem, physically-based methods relying on objective and measurable vegetation properties are advantageous for describing complex vegetation. We have conducted flume and towing tank investigations with living and artificial plants, both in arrays and with isolated plants, providing new insight into advanced parameterization of natural vegetation. The stem, leaf and total areas of the trees confirmed to be suitable characteristic dimensions for estimating flow resistance. Consequently, we propose the use of leaf area index and leaf-to-stem-area ratio to achieve better drag force estimates. Novel remote sensing techniques including laser scanning have become available for effective collection of the required data. The benefits of the proposed parameterization have been clearly demonstrated in our newest experimental studies, but it remains to be investigated to what extent the parameter values are species-specific and how they depend on local habitat conditions. The purpose of this contribution is to summarize developments in the estimation of vegetative drag force based on physically-based approaches as the latest research results are somewhat dispersed. In particular, concerning woody vegetation we seek to discuss three issues: 1) parameterization of reconfiguration with the Vogel exponent; 2) advantage of parameterizing plants with the leaf area
Direct measurements of controlled aerodynamic forces on a wire-suspended axisymmetric body
NASA Astrophysics Data System (ADS)
Abramson, Philip; Vukasinovic, Bojan; Glezer, Ari
2011-06-01
A novel in-line miniature force transducer is developed for direct measurements of the net aerodynamic forces and moments on a bluff body. The force transducers are integrated into each of the eight mounting wires that are utilized for suspension of an axisymmetric model in a wind tunnel having minimal wake interference. The aerodynamic forces and moments on the model are altered by induced active local attachment of the separated base flow. Fluidic control is effected by an array of four integrated aft-facing synthetic jet actuators that emanate from narrow, azimuthally segmented slots, equally distributed around the perimeter of the circular tail end. The jet orifices are embedded within a small backward-facing step that extends into a Coanda surface. The altered flow dynamics associated with both quasi-steady and transitory asymmetric activation of the flow control effect is characterized by direct force and PIV measurements.
Bahlman, Joseph W; Swartz, Sharon M; Breuer, Kenneth S
2014-06-01
Bats display a wide variety of behaviors that require different amounts of aerodynamic force. To control and modulate aerodynamic force, bats change wing kinematics, which, in turn, may change the power required for wing motion. There are many kinematic mechanisms that bats, and other flapping animals, can use to increase aerodynamic force, e.g. increasing wingbeat frequency or amplitude. However, we do not know if there is a difference in energetic cost between these different kinematic mechanisms. To assess the relationship between mechanical power input and aerodynamic force output across different isolated kinematic parameters, we programmed a robotic bat wing to flap over a range of kinematic parameters and measured aerodynamic force and mechanical power. We systematically varied five kinematic parameters: wingbeat frequency, wingbeat amplitude, stroke plane angle, downstroke ratio, and wing folding. Kinematic values were based on observed values from free flying Cynopterus brachyotis, the species on which the robot was based. We describe how lift, thrust, and power change with increases in each kinematic variable. We compare the power costs associated with generating additional force through the four kinematic mechanisms controlled at the shoulder, and show that all four mechanisms require approximately the same power to generate a given force. This result suggests that no single parameter offers an energetic advantage over the others. Finally, we show that retracting the wing during upstroke reduces power requirements for flapping and increases net lift production, but decreases net thrust production. These results compare well with studies performed on C. brachyotis, offering insight into natural flight kinematics. PMID:24851830
Tethered cells in fluid flows--beyond the Stokes' drag force approach.
Zakrisson, Johan; Wiklund, Krister; Axner, Ove; Andersson, Magnus
2015-10-01
Simulations of tethered cells in viscous sub-layers are frequently performed using the Stokes' drag force, but without taking into account contributions from surface corrections, lift forces, buoyancy, the Basset force, the cells' finite inertia, or added mass. In this work, we investigate to what extent such contributions, under a variety of hydrodynamic conditions, influence the force at the anchor point of a tethered cell and the survival probability of a bacterium that is attached to a host by either a slip or a catch bond via a tether with a few different biomechanical properties. We show that a consequence of not including some of these contributions is that the force to which a bond is exposed can be significantly underestimated; in general by ∼32-46%, where the influence of the surface corrections dominate (the parallel and normal correction coefficients contribute ∼5-8 or ∼23-26%, respectively). The Basset force is a major contributor, up to 20%, for larger cells and shear rates. The lift force and inertia contribute when cells with radii >3 μm have shear rates >2000 s(-1). Buoyancy contributes significantly for cells with radii >3 μm for shear rates <10 s(-1). Since the lifetime of a bond depends strongly on the force, both the level of approximation and the biomechanical model of the tether significantly affect the survival probability of tethered bacteria. For a cell attached by a FimH-mannose bond and an extendable tether with a shear rate of 3000 s(-1), neglecting the surface correction coefficients or the Basset force can imply that the survival probability is overestimated by more than an order of magnitude. This work thus shows that in order to quantitatively assess bacterial attachment forces and survival probabilities, both the fluid forces and the tether properties need to be modeled accurately. PMID:26331992
Tethered cells in fluid flows—beyond the Stokes’ drag force approach
NASA Astrophysics Data System (ADS)
Zakrisson, Johan; Wiklund, Krister; Axner, Ove; Andersson, Magnus
2015-10-01
Simulations of tethered cells in viscous sub-layers are frequently performed using the Stokes’ drag force, but without taking into account contributions from surface corrections, lift forces, buoyancy, the Basset force, the cells’ finite inertia, or added mass. In this work, we investigate to what extent such contributions, under a variety of hydrodynamic conditions, influence the force at the anchor point of a tethered cell and the survival probability of a bacterium that is attached to a host by either a slip or a catch bond via a tether with a few different biomechanical properties. We show that a consequence of not including some of these contributions is that the force to which a bond is exposed can be significantly underestimated; in general by ˜32-46%, where the influence of the surface corrections dominate (the parallel and normal correction coefficients contribute ˜5-8 or ˜23-26%, respectively). The Basset force is a major contributor, up to 20%, for larger cells and shear rates. The lift force and inertia contribute when cells with radii >3 μm have shear rates >2000 s-1. Buoyancy contributes significantly for cells with radii >3 μm for shear rates <10 s-1. Since the lifetime of a bond depends strongly on the force, both the level of approximation and the biomechanical model of the tether significantly affect the survival probability of tethered bacteria. For a cell attached by a FimH-mannose bond and an extendable tether with a shear rate of 3000 s-1, neglecting the surface correction coefficients or the Basset force can imply that the survival probability is overestimated by more than an order of magnitude. This work thus shows that in order to quantitatively assess bacterial attachment forces and survival probabilities, both the fluid forces and the tether properties need to be modeled accurately.
Formosa, Danielle P; Sayers, Mark G L; Burkett, Brendan
2014-01-01
This study used both an instantaneous net drag force profile and a symmetry timing to evaluate the effect of the breathing action on stroke coordination. Twenty elite swimmers completed a total of six randomised front-crawl towing trials: (i) three breathing trials and (ii) three non-breathing trials. The net drag force was measured using an assisted towing device mounted upon a Kistler force platform, and this equipment towed the swimmer at a constant speed. The net drag force profile was used to create a stroke symmetry index for each swimming trial. Analysis using the symmetry indices identified that the majority of participants demonstrated an asymmetrical instantaneous net drag force stroke profile in both the breathing and non-breathing conditions, despite no significant differences in the time from finger-tip entry to finger-tip exit. Within the breathing condition, the faster swimmers compared to the slower swimmers demonstrated a lesser percentage of overlap between stroke phases on their breathing stroke side. During the non-breathing condition, the faster participants compared to the slower swimmers recorded a reduction in the percentage of overlap between stroke phases and less duration in the underwater stroke on their breathing stroke side. This study identified that the majority of participants demonstrated an asymmetrical net drag force profile within both conditions; however, asymmetry was less prevalent when examining with only the timing symmetry index. PMID:24861056
NASA Astrophysics Data System (ADS)
Brooks, Jason W.; Matzner, Richard
2016-07-01
produces all components of the thermally induced force on the satellite as a function of time throughout the orbit. We find that in the slow spin regime, although there are substantial excursions from the Fourier results, the Fourier results do provide good average values for the temperature of the CCRs (constant temperature in rows from the Fourier method), and for the daily along-track average drag. However, we also find that the relatively small average along-track drag (which swings between -0.7 pm/s2 and -0.25 pm/s2 and averages -0.50 pm/s2 over days 1460-1580) arises from instantaneous accelerations that have excursions that are about an order of magnitude larger than the resulting orbit-averaged drag. Note that neither the first paper nor this one addresses the additional particle drag on the satellite.
NASA Astrophysics Data System (ADS)
Nwankwo, Victor U. J.; Chakrabarti, Sandip Kumar
The International Space Station (ISS) is the single largest and most complex scientific and engineering space structure in human history. Its orbital parameters make it extremely vulnerable to severe atmospheric drag force. Complex interactions between solar energetic particles, ultraviolet (UV) radiation with atmosphere and geomagnetic field cause heating and subsequent expansion of the upper atmosphere. This condition increases drag on low Earth orbit satellites (LEOSs) and varies with current space weather conditions. In this work, we apply the NRLMSISE-00 empirical atmospheric density model, as a function of space environmental parameters, to model drag force impact on a model LEOS during variation of solar activity. Applying the resulting drag model on a model ISS satellite we observe that depending on the severity and/or stage of solar activity or cycle, a massive artificial satellite could experience orbit decay rate of up to 2.95km/month during solar maximum and up to 1km/month during solar minimum.
Single Cell Mass Measurement Using Drag Force Inside Lab-on-Chip Microfluidics System.
Rahman, Md Habibur; Ahmad, Mohd Ridzuan; Takeuchi, Masaru; Nakajima, Masahiro; Hasegawa, Yasuhisa; Fukuda, Toshio
2015-12-01
Single cell mass (SCM) is an intrinsic property of single cell, it arouses a great interest among scientists as cell mass depends on the synthesis of proteins, DNA replication, cell wall stiffness, cell cytoplasm density, cell growth, ribosome, and other analogous of organisms. To date, several great strides have been taken to the advancements of SCM measurement techniques. Nevertheless, more works are required to enable the technology to push frontier in deep analysis of SCM measurement, hence to elucidate intracellular properties. In this paper, we present a lab-on-chip microfluidics system for SCM measurement, related with the force required to drag a single cell and Newton's law of motion inside microfluidics channel. Drag force on the cell was generated by a pressure driven syringe micropump and the motion of the cell was measured using optical observation under an inverted microscope. This approach of measuring SCM was calibrated using known mass (77.3 pg) of a polystyrene particle of 5.2 μm diameter. Furthermore, we used Saccharomyces cerevisiae baker's yeast cells of different sizes ([Formula: see text] diameter) for SCM measurement. Mass of 4.4 μm diameter of single yeast cell was measured as 2.12 pg which is in the range of previously reported single yeast cell mass (2-3 pg). In addition, we also studied the relation between SCM and single cell size. Results showed that single yeast cell mass increases exponentially with the increasing of single cell size. PMID:26761952
The dust motion inside the magnetized sheath - The effect of drag forces
Pandey, B. P.; Samarian, A.; Vladimirov, S. V.
2010-08-15
The isolated charged dust inside the magnetized plasma sheath moves under the influence of the electron and ion drag force and the sheath electrostatic field. The charge on the dust is a function of its radius as well as the value of the ambient sheath potential. It is shown that the charge on the dust determines its trajectory and dust performs the spiraling motion inside the sheath. The location of the turning spiral is determined by the number of negative charge on the dust, which in turn is a function of the dust radius. The back and forth spiraling motion finally causes the dust to move in a small, narrow region of the sheath. For a bigger dust particle, the dust moves closer to the sheath presheath boundary suggesting that the bigger grains, owing to the strong repulsion between the wall and dust, will be unable to travel inside the sheath. Only small, micron-sized grains can travel closer to the wall before repulsion pushes it back toward the plasma-sheath boundary. The temporal behavior of the spiraling dust motion appears like a damped harmonic oscillation, suggesting that the plasma drag force causes dissipation of the electrostatic energy. However, after initial damping, the grain keeps oscillating although with much smaller amplitude. The possible application of the present results to the ongoing sheath experiments is discussed.
NASA Technical Reports Server (NTRS)
Nielsen, Jack N.
1988-01-01
The fundamental aerodynamics of slender bodies is examined in the reprint edition of an introductory textbook originally published in 1960. Chapters are devoted to the formulas commonly used in missile aerodynamics; slender-body theory at supersonic and subsonic speeds; vortices in viscid and inviscid flow; wing-body interference; downwash, sidewash, and the wake; wing-tail interference; aerodynamic controls; pressure foredrag, base drag, and skin friction; and stability derivatives. Diagrams, graphs, tables of terms and formulas are provided.
Pruitt, J.M.; Hassan, Y.A. ); Steininger, D.A.
1990-01-01
Excessive tube vibration caused by turbulent flow buffeting and fluid-elastic excitation is one of the main problems associated with steam generators. Vibration can lead to rupture of tubes within the steam generator, necessitating plugging, and perhaps even replacement of the component. Turbulence buffeting, and resulting excitation, is believed to be one of the mechanisms leading to tube vibration. The large-eddy simulation (LES) technique is being considered as a possible design analysis tool for defining the temporally fluctuating forces on steam generator tube banks. The present investigation uses LES to calculate the flow field for an array of tubes subject to turbulent flow and to compare the fluctuating lift and drag forces on a central tube with experimental findings. Predictions to date using LES methodology compare quite favorably with experimental data.
Maximum Aerodynamic Force on an Ascending Space Vehicle
NASA Astrophysics Data System (ADS)
Backman, Philip
2012-03-01
The March 2010 issue of The Physics Teacher includes a great article by Metz and Stinner on the kinematics and dynamics of a space shuttle launch. Within those pages is a brief mention of an event known in the language of the National Aeronautics and Space Administration (NASA) as "maximum dynamic pressure" (called simply "Max.AirPressure" in the article), where the combined effect of air density and the shuttles speed produce the greatest aerodynamic stress on the vehicle as it ascends through the atmosphere toward orbit. Official commentary during a launch2 refers to this point in the ascent with language such as "space shuttle main engines throttling back as vehicle enters area of maximum dynamic pressure" and occurs in a range between 45 and 60 s after launch. (In dealing with this stress, the space shuttles main engines reduce their thrust at approximately 45 s to reduce acceleration, and return to normal levels again some 15 s later as maximum dynamic pressure is traversed.) This paper presents an analysis, accessible to introductory-level students, that predicts the time of Max. AirPressure for a given ascending spacecraft.
NASA Technical Reports Server (NTRS)
Pamadi, Bandu N.; Taylor, Lawrence W., Jr.
1987-01-01
A semi-empirical method is presented for the estimation of aerodynamic forces and moments acting on a steadily spinning (rotating) light airplane. The airplane is divided into wing, body, and tail surfaces. The effect of power is ignored. The strip theory is employed for each component of the spinning airplane to determine its contribution to the total aerodynamic coefficients. Then, increments to some of the coefficients which account for centrifugal effect are estimated. The results are compared to spin tunnel rotary balance test data.
A force balance system for the measurement of skin friction drag force
NASA Technical Reports Server (NTRS)
Moore, J. W.; Mcvey, E. S.
1971-01-01
Research on force balance instrumentation to measure the skin friction of hypersonic vehicles at extreme temperatures, high altitudes and in a vibration field is discussed. A rough overall summary and operating instructions for the equipment are presented.
Dynamic control of aerodynamic forces on a moving platform using active flow control
NASA Astrophysics Data System (ADS)
Brzozowski, Daniel P.
The unsteady interaction between trailing edge aerodynamic flow control and airfoil motion in pitch and plunge is investigated in wind tunnel experiments using a two degree-of-freedom traverse which enables application of time-dependent external torque and forces by servo motors. The global aerodynamic forces and moments are regulated by controlling vorticity generation and accumulation near the trailing edge of the airfoil using hybrid synthetic jet actuators. The dynamic coupling between the actuation and the time-dependent flow field is characterized using simultaneous force and particle image velocimetry (PIV) measurements that are taken phase-locked to the commanded actuation waveform. The effect of the unsteady motion on the model-embedded flow control is assessed in both trajectory tracking and disturbance rejection maneuvers. The time-varying aerodynamic lift and pitching moment are estimated from a PIV wake survey using a reduced order model based on classical unsteady aerodynamic theory. These measurements suggest that the entire flow over the airfoil readjusts within 2--3 convective time scales, which is about two orders of magnitude shorter than the characteristic time associated with the controlled maneuver of the wind tunnel model. This illustrates that flow-control actuation can be typically effected on time scales that are commensurate with the flow's convective time scale, and that the maneuver response is primarily limited by the inertia of the platform.
Asymmetric aerodynamic forces on aircraft at high angles of attack - some design guides
NASA Technical Reports Server (NTRS)
Chapman, G. T.; Keener, E. R.; Malcolm, G. N.
1976-01-01
Aerodynamic side forces on forebodies are considered that are produced by two types of flow: asymmetric vortices on bodies of revolution and nonuniform flow separation on square bodies with rounded corners under spinning conditions. Steady side forces that can be as large as the normal force are produced by asymmetric vortices on pointed forebodies. This side force has a large variation with Reynolds number, decreases rapidly with Mach number, and can be nearly eliminated with small nose bluntness or strakes. The angle of attack where the side force first occurs depends primarily on body geometry. The theoretical techniques to predict these side forces are necessarily semi-empirical because the basic phenomenon is not well understood. The side forces produced by nonuniform flow separation under spinning conditions depend extensively on spin rate, angle of attack, and Reynolds number. The application of simple crossflow theory to predict this side force is inadequate much below angles of attack of 90 deg.
Aerodynamic effects of flexibility in flapping wings
Zhao, Liang; Huang, Qingfeng; Deng, Xinyan; Sane, Sanjay P.
2010-01-01
Recent work on the aerodynamics of flapping flight reveals fundamental differences in the mechanisms of aerodynamic force generation between fixed and flapping wings. When fixed wings translate at high angles of attack, they periodically generate and shed leading and trailing edge vortices as reflected in their fluctuating aerodynamic force traces and associated flow visualization. In contrast, wings flapping at high angles of attack generate stable leading edge vorticity, which persists throughout the duration of the stroke and enhances mean aerodynamic forces. Here, we show that aerodynamic forces can be controlled by altering the trailing edge flexibility of a flapping wing. We used a dynamically scaled mechanical model of flapping flight (Re ≈ 2000) to measure the aerodynamic forces on flapping wings of variable flexural stiffness (EI). For low to medium angles of attack, as flexibility of the wing increases, its ability to generate aerodynamic forces decreases monotonically but its lift-to-drag ratios remain approximately constant. The instantaneous force traces reveal no major differences in the underlying modes of force generation for flexible and rigid wings, but the magnitude of force, the angle of net force vector and centre of pressure all vary systematically with wing flexibility. Even a rudimentary framework of wing veins is sufficient to restore the ability of flexible wings to generate forces at near-rigid values. Thus, the magnitude of force generation can be controlled by modulating the trailing edge flexibility and thereby controlling the magnitude of the leading edge vorticity. To characterize this, we have generated a detailed database of aerodynamic forces as a function of several variables including material properties, kinematics, aerodynamic forces and centre of pressure, which can also be used to help validate computational models of aeroelastic flapping wings. These experiments will also be useful for wing design for small robotic
Drag forces of natural trees of different size: experiments in a towing tank
NASA Astrophysics Data System (ADS)
Jalonen, Johanna; Järvelä, Juha
2013-04-01
Reliable estimation of hydraulic resistance is of great importance in practical applications such as river and wetland restoration as well as flood prediction and management. Parameters describing riparian vegetation need to be physically sound and readily measurable. For these purposes, several researchers have studied the hydraulic resistance in flumes with living and artificial plants both in arrays and with isolated plants. However, due to the restrictions of flume size the experiments are often conducted with parts of trees, twigs or branches. Consequently, it is not clear how the size (parts of trees or small trees vs. full scale trees) affects the hydraulic resistance. We conducted direct drag force measurements for 23 tree individuals of different heights (0.9 m - 3.5 m) in a towing tank. The investigated species were Common Alder (Alnus glutinosa), Goat Willow (Salix caprea), Silver Birch (Betula pendula) and White Birch (Betula pubescens). The forces were measured at velocity ranges of 0.1-2.5 m/s and 0.1-2.0 m/s both in leafy and leafless conditions, respectively. The measurement system consisted of three load cells measuring the main flow direction. Two different load cell setups were used depending on the size of the specimen to allow for accurate force measurement. For the smaller trees the load cells were replaced with more sensitive sensors, and the resulting ranges of the load cells were from 1 to 1000 N and from 0.1 to 100 N. Frontal and side projected areas and bending of the specimens were recorded during the measurements using submerged video cameras. For all specimens, wet and dry biomass, projected area in still air, and one-sided leaf area were determined. In order to construct a 3D-model of the trees, the specimens were laser scanned from three directions with a terrestrial laser scanner (TLS). The resulting point cloud had a millimeter resolution, and provided detailed information about the plant characteristics, such as leaf area
Drag reduction over dolphin skin via the pondermotive forcing of vortex filaments
NASA Astrophysics Data System (ADS)
Lisi, Antony Garrett
1999-11-01
The skin of Tursiops Truncatus is corrugated with small, quasi-periodic ridges running circumferentially about the torso. These ridges extend into the turbulent boundary layer and affect the evolution of coherent structures. The development and evolution of coherent structures over a surface is described by the formation and dynamics of vortex filaments. The dynamics of these filaments over a flat, non-ridged surface is determined analytically, as well as through numerical simulation, and found to agree with the observations of coherent structures in the turbulent boundary layer. The calculation of the linearized dynamics of the vortex filament, successful for the dynamics of a filament over a flat surface, is extended and applied to a vortex filament propagating over a periodically ridged surface. The surface ridges induce a rapid parametric forcing of the vortex filament, and alter the filament dynamics significantly. A consideration of the contribution of vortex filament induced flow to energy transport indicates that the behavior of the filament induced by the ridges can directly reduce surface drag by up to 8%. The size, shape, and distribution of cutaneous ridges for Tursiops Truncatus is found to be optimally configured to affect the filament dynamics and reduce surface drag for swimming velocities consistent with observation.
Ion collection by a sphere in a flowing plasma: 3. Floating potential and drag force
NASA Astrophysics Data System (ADS)
Hutchinson, I. H.
2005-01-01
The interaction of an ion-collecting sphere at floating potential with a flowing collisionless plasma is investigated using the particle in cell code SCEPTIC. The dependence of the floating potential on the flow velocity for a conducting sphere is found to agree very well with the orbital motion limited approximation, which ignores the asymmetry in the plasma potential. But the charge, even on conducting spheres and at zero flow, is not well represented by using the standard expression for capacitance. Insulating spheres become asymmetrically charged because of ion collection asymmetry, and their total (negative) charge is considerably increased by flow. The collection flux asymmetry is documented for both conducting and insulating spheres and is not greatly different between them. The drag force upon the sphere is obtained from the code calculations. It shows reasonable agreement with appropriate analytic approximations. However, numerical discrepancies up to 20% are found, which are attributed to uncertainties in the analytical values.
Electrostatic disturbance forces on a 3-axis drag-free sensor. [for earth satellite accelerometry
NASA Technical Reports Server (NTRS)
Hagstrom, T.; Sonnabend, D.; Vijayaraghavan, A.
1982-01-01
The electrostatic analysis of a multiple-capacitance 3-axis drag-free sensor is presented in this paper. The instrument consists of a proof-mass (a dense metallic ball) floating freely inside a spherical cavity enclosed by the sensor plates and the shield. Since the ball and the cavity are not necessarily concentric, the problem in three-dimensional potential theory for electrostatics is solved by the method of boundary perturbations and specifically in terms of spherical harmonics. The capacitance outputs of the instrument and the electrostatic forces acting on the system are derived as non-linear functions of the ball position, ball charge and the sensor plate potentials. The instrument sensitivity and cross-coupling effects are discussed. The analysis may also be useful for electrostatic gyros and suspensions.
Geometry of halo and Lissajous orbits in the circular restricted three-body problem with drag forces
NASA Astrophysics Data System (ADS)
Pal, Ashok Kumar; Kushvah, Badam Singh
2015-01-01
In this paper, we determine the effect of radiation pressure, Poynting-Robertson drag and solar wind drag on the Sun-(Earth-Moon) restricted three-body problem. Here, we take the larger body of the Sun as a larger primary, and the Earth+Moon as a smaller primary. With the help of the perturbation technique, we find the Lagrangian points, and see that the collinear points deviate from the axis joining the primaries, whereas the triangular points remain unchanged in their configuration. We also find that Lagrangian points move towards the Sun when radiation pressure increases. We have also analysed the stability of the triangular equilibrium points and have found that they are unstable because of the drag forces. Moreover, we have computed the halo orbits in the third-order approximation using the Lindstedt-Poincaré method and have found the effect of the drag forces. According to this prevalence, the Sun-(Earth-Moon) model is used to design the trajectory for spacecraft travelling under drag forces.
Drag force, diffusion coefficient, and electric mobility of small particles. II. Application.
Li, Zhigang; Wang, Hai
2003-12-01
We propose a generalized treatment of the drag force of a spherical particle due to its motion in a laminar fluid media. The theory is equally applicable to analysis of particle diffusion and electric mobility. The focus of the current analysis is on the motion of spherical particles in low-density gases with Knudsen number Kn>1. The treatment is based on the gas-kinetic theory analysis of drag force in the specular and diffuse scattering limits obtained in a preceding paper [Z. Li and H. Wang, Phys. Rev. E., 68, 061206 (2003)]. Our analysis considers the influence of van der Waals interactions on the momentum transfer upon collision of a gas molecule with the particle and expresses this influence in terms of an effective, reduced collision integral. This influence is shown to be significant for nanosized particles. In the present paper, the reduced collision integral values are obtained for specular and diffuse scattering, using a Lennard-Jones-type potential energy function suitable for the interactions of a gas molecule with a particle. An empirical formula for the momentum accommodation function, used to determine the effective, reduced collision integral, is obtained from available experimental data. The resulting treatment is shown to be accurate for interpreting the mobility experiments for particles as small as approximately 1 nm in radius. The treatment is subsequently extended to the entire range of the Knudsen number, following a semiempirical, gas-kinetic theory analysis. We demonstrate that the proposed formula predicts very well Millikan's oil-droplet experiments [R. A. Millikan, Philos. Mag. 34, 1 (1917); Phys. Rev. 22, 1 (1923)]. The rigorous theoretical foundation of the proposed formula in the Kn>1 limit makes the current theory far more general than the semiempirical Stokes-Cunningham formula in terms of the particle size and condition of the fluid and, therefore, more attractive than the Stokes-Cunningham formula. PMID:14754192
Drag force, diffusion coefficient, and electric mobility of small particles. II. Application
NASA Astrophysics Data System (ADS)
Li, Zhigang; Wang, Hai
2003-12-01
We propose a generalized treatment of the drag force of a spherical particle due to its motion in a laminar fluid media. The theory is equally applicable to analysis of particle diffusion and electric mobility. The focus of the current analysis is on the motion of spherical particles in low-density gases with Knudsen number Kn≫1. The treatment is based on the gas-kinetic theory analysis of drag force in the specular and diffuse scattering limits obtained in a preceding paper [Z. Li and H. Wang, Phys. Rev. E., 68, 061206 (2003)]. Our analysis considers the influence of van der Waals interactions on the momentum transfer upon collision of a gas molecule with the particle and expresses this influence in terms of an effective, reduced collision integral. This influence is shown to be significant for nanosized particles. In the present paper, the reduced collision integral values are obtained for specular and diffuse scattering, using a Lennard-Jones-type potential energy function suitable for the interactions of a gas molecule with a particle. An empirical formula for the momentum accommodation function, used to determine the effective, reduced collision integral, is obtained from available experimental data. The resulting treatment is shown to be accurate for interpreting the mobility experiments for particles as small as ˜1 nm in radius. The treatment is subsequently extended to the entire range of the Knudsen number, following a semiempirical, gas-kinetic theory analysis. We demonstrate that the proposed formula predicts very well Millikan’s oil-droplet experiments [R. A. Millikan, Philos. Mag. 34, 1 (1917); Phys. Rev. 22, 1 (1923)]. The rigorous theoretical foundation of the proposed formula in the Kn≫1 limit makes the current theory far more general than the semiempirical Stokes-Cunningham formula in terms of the particle size and condition of the fluid and, therefore, more attractive than the Stokes-Cunningham formula.
Turbulence and turbulent drag reduction in swirling flow: Inertial versus viscous forcing.
Burnishev, Yuri; Steinberg, Victor
2015-08-01
We report unexpected results of a drastic difference in the transition to fully developed turbulent and turbulent drag reduction (TDR) regimes and in their properties in a von Karman swirling flow with counter-rotating disks of water-based polymer solutions for viscous (by smooth disks) as well as inertial (by bladed disks) forcing and by tracking just torque Γ(t) and pressure p(t) . For the viscous forcing, just a single TDR regime is found with the transition values of the Reynolds number (Re) Re turb c =Re TDR c ≃(4.8±0.2)×10(5) independent of ϕ , whereas for the inertial forcing two turbulent regimes are revealed. The first transition is to fully developed turbulence, and the second one is to the TDR regime with both Re turb c and Re TDR c depending on polymer concentration ϕ . Both regimes differ by the values of C f and C p , by the scaling exponents of the fundamental turbulent characteristics, by the nonmonotonic dependencies of skewness and flatness of the pressure PDFs on Re, and by the different frequency power spectra of p with the different dependencies of the main vortex peak frequency in the p power spectra on ϕ and Re. Thus our experimental results show the transition to the TDR regime in a von Karman swirling flow for the viscous and inertial forcings in a sharp contrast to the recent experiments [Phys. Fluids 10, 426 (1998); Phys. Rev. E 47, R28(R) (1993); and J. Phys.: Condens. Matter 17, S1195 (2005)] where the transition to TDR is observed in the same swirling flow with counter-rotating disks only for the viscous forcing. The latter result has led its authors to the wrong conclusion that TDR is a solely boundary effect contrary to the inertial forcing associated with the bulk effect, and this conception is currently rather widely accepted in literature. PMID:26382497
Sensitivity of aerodynamic forces in laminar and turbulent flow past a square cylinder
NASA Astrophysics Data System (ADS)
Meliga, Philippe; Boujo, Edouard; Pujals, Gregory; Gallaire, François
2014-10-01
We use adjoint-based gradients to analyze the sensitivity of the drag force on a square cylinder. At Re = 40, the flow settles down to a steady state. The quantity of interest in the adjoint formulation is the steady asymptotic value of drag reached after the initial transient, whose sensitivity is computed solving a steady adjoint problem from knowledge of the stable base solution. At Re = 100, the flow develops to the time-periodic, vortex-shedding state. The quantity of interest is rather the time-averaged mean drag, whose sensitivity is computed integrating backwards in time an unsteady adjoint problem from knowledge of the entire history of the vortex-shedding solution. Such theoretical frameworks allow us to identify the sensitive regions without computing the actually controlled states, and provide a relevant and systematic guideline on where in the flow to insert a secondary control cylinder in the attempt to reduce drag, as established from comparisons with dedicated numerical simulations of the two-cylinder system. For the unsteady case at Re = 100, we also compute an approximation to the mean drag sensitivity solving a steady adjoint problem from knowledge of only the mean flow solution, and show the approach to carry valuable information in view of guiding relevant control strategy, besides reducing tremendously the related numerical effort. An extension of this simplified framework to turbulent flow regime is examined revisiting the widely benchmarked flow at Reynolds number Re = 22 000, the theoretical predictions obtained in the frame of unsteady Reynolds-averaged Navier-Stokes modeling being consistent with experimental data from the literature. Application of the various sensitivity frameworks to alternative control objectives such as increasing the lift and reducing the fluctuating drag and lift is also discussed and illustrated with a few selected examples.
NASA Astrophysics Data System (ADS)
You, Zhenjiang; Bedrikovetsky, Pavel; Badalyan, Alexander; Hand, Martin
2015-04-01
The fluid flow in natural reservoirs mobilizes fine particles. Subsequent migration and straining of the mobilized particles in rocks greatly reduce reservoir permeability and well productivity. This chain of events typically occurs over the temperature ranges of 20-40°C for aquifers and 120-300°C for geothermal reservoirs. However, the present study might be the first to present a quantitative analysis of temperature effects on the forces exerted on particles and of the resultant fines migration. Based on torque balance between electrostatic and drag forces acting on attached fine particles, we derived a model for the maximum retention concentration and used it to characterize the detachment of multisized particles from rock surfaces. Results showed that electrostatic force is far more affected than water viscosity by temperature variation. An analytical model for flow toward wellbore that is subject to fines migration was derived. The experiment-based predictive modeling of the well impedance for a field case showed high agreement with field historical data (coefficient of determination R2 = 0.99). It was found that the geothermal reservoirs are more susceptible to fine particle migration than are conventional oilfields and aquifers.
NASA Technical Reports Server (NTRS)
Petot, D.; Loiseau, H.
1982-01-01
Unsteady aerodynamic methods adopted for the study of aeroelasticity in helicopters are considered with focus on the development of a semiempirical model of unsteady aerodynamic forces acting on an oscillating profile at high incidence. The successive smoothing algorithm described leads to the model's coefficients in a very satisfactory manner.
Numerical Simulation of Flow and Determination of Aerodynamic Forces in the Balanced Control Valve
NASA Astrophysics Data System (ADS)
Matas, R.; Straka, F.; Hoznedl, M.
2013-04-01
The contribution subscribes a numerical simulation of a steam flow through a balanced control valve. The influence of some parameters in simulations were tested, analyzed and discussed. As a result of the simulations a graph of aerodynamics forces for a specific turbine characteristic was obtained. The results from numerical simulations were compared with results from experiments. The experiment was performed with an air flow, but the final data were converted with a criterion to steam flow.
Structural effects of unsteady aerodynamic forces on horizontal-axis wind turbines
Miller, M.S.; Shipley, D.E.
1994-08-01
Due to its renewable nature and abundant resources, wind energy has the potential to fulfill a large portion of this nation`s energy needs. The simplest means of utilizing wind energy is through the use of downwind, horizontal-axis wind turbines (HAWT) with fixed-pitch rotors. This configuration regulates the peak power by allowing the rotor blade to aerodynamically stall. The stall point, the point of maximum coefficient of lift, is currently predicted using data obtained from wind tunnel tests. Unfortunately, these tests do not accurately simulate conditions encountered in the field. Flow around the tower and nacelle coupled with inflow turbulence and rotation of the turbine blades create unpredicted aerodynamic forces. Dynamic stall is hypothesized to occur. Such aerodynamic loads are transmitted into the rotor and tower causing structural resonance that drastically reduces the design lifetime of the wind turbine. The current method of alleviating this problem is to structurally reinforce the tower and blades. However, this adds unneeded mass and, therefore, cost to the turbines. A better understanding of the aerodynamic forces and the manner in which they affect the structure would allow for the design of more cost effective and durable wind turbines. Data compiled by the National Renewable Energy Laboratory (NREL) for a downwind HAWT with constant chord, untwisted, fixed-pitch rotors is analyzed. From these data, the actual aerodynamic characteristics of the rotor are being portrayed and the potential effects upon the structure can for the first time be fully analyzed. Based upon their understanding, solutions to the problem of structural resonance are emerging.
Structural effects of unsteady aerodynamic forces on horizontal-axis wind turbines
NASA Astrophysics Data System (ADS)
Miller, M. S.; Shipley, D. E.
1994-08-01
Due to its renewable nature and abundant resources, wind energy has the potential to fulfill a large portion of this nation's energy needs. The simplest means of utilizing wind energy is through the use of downwind, horizontal-axis wind turbines (HAWT) with fixed-pitch rotors. This configuration regulates the peak power by allowing the rotor blade to aerodynamically stall. The stall point, the point of maximum coefficient of lift, is currently predicted using data obtained from wind tunnel tests. Unfortunately, these tests do not accurately simulate conditions encountered in the field. Flow around the tower and nacelle coupled with inflow turbulence and rotation of the turbine blades create unpredicted aerodynamic forces. Dynamic stall is hypothesized to occur. Such aerodynamic loads are transmitted into the rotor and tower causing structural resonance that drastically reduces the design lifetime of the wind turbine. The current method of alleviating this problem is to structurally reinforce the tower and blades. However, this adds unneeded mass and, therefore, cost to the turbines. A better understanding of the aerodynamic forces and the manner in which they affect the structure would allow for the design of more cost effective and durable wind turbines. Data compiled by the National Renewable Energy Laboratory (NREL) for a downwind HAWT with constant chord, untwisted, fixed-pitch rotors is analyzed. From these data, the actual aerodynamic characteristics of the rotor are being portrayed and the potential effects upon the structure can for the first time be fully analyzed. Based upon their understanding, solutions to the problem of structural resonance are emerging.
Mullins, Benjamin J; Braddock, Roger D; Agranovski, Igor E; Cropp, Roger A; O'Leary, Rebecca A
2005-04-01
Extensive experimental investigation of the wetting processes of fibre-liquid systems during air filtration (when drag and gravitational forces are acting) has shown many important features, including droplet extension, oscillatory motion, and detachment of drops from fibres as airflow velocity increases, and also movement or flow of droplets along fibres. A detailed experimental study of the processes was conducted using stainless steel filter fibres and H2O aerosol, which coalesce on the fibre to form clamshell droplets. The droplets were predominantly observed in the Reynolds transition flow region, since this is the region where most of the above features occur. The droplet oscillation is believed to be induced by the onset of the transition from laminar to turbulent flow as the increasing droplet size increases Reynolds number for the flow around the droplet. Two-dimensional flow in this region is usually modelled using the classical Karman vortex street, however there exist no 3D equivalents. Therefore to model such oscillation it was necessary to create a new conceptual model to account for the forces both inducing and preventing such oscillation. The agreement between the model and experimental results is very good for both the radial and transverse oscillations. PMID:15752809
Microfluidic acoustic trapping force and stiffness measurement using viscous drag effect
Lee, Jungwoo; Jeong, Jong Seob; Shung, K. Kirk
2013-01-01
It has recently been demonstrated that it was possible to individually trap 70 μm droplets flowing within a 500 μm wide microfluidic channel by a 24 MHz single element piezo-composite focused transducer. In order to further develop this non-invasive approach as a microfluidic particle manipulation tool of high precision, the trapping force needs to be calibrated to a known force, i.e., viscous drag force arising from the fluid flow in the channel. However, few calibration studies based on fluid viscosity have been carried out with focused acoustic beams for moving objects in microfluidic environments. In this paper, the acoustic trapping force (Ftrapping) and the trap stiffness (or compliance k) are experimentally determined for a streaming droplet in a microfluidic channel. Ftrapping is calibrated to viscous drag force produced from syringe pumps. Chebyshev-windowed chirp coded excitation sequences sweeping the frequency range from 18 MHz to 30 MHz is utilized to drive the transducer, enabling the beam transmission through the channel/fluid interface for interrogating the droplets inside the channel. The minimum force (Fmin,trapping) required for initially immobilizing drifting droplets is determined as a function of pulse repetition frequency (PRF), duty factor (DTF), and input voltage amplitude (Vin) to the transducer. At PRF = 0.1 kHz and DTF = 30%, Fmin,trapping is increased from 2.2 nN for Vin = 22 Vpp to 3.8 nN for Vin = 54 Vpp. With a fixed Vin = 54 Vpp and DTF = 30%, Fmin,trapping can be varied from 3.8 nN at PRF = 0.1 kHz to 6.7 nN at PRF = 0.5 kHz. These findings indicate that both higher driving voltage and more frequent beam transmission yield stronger traps for holding droplets in motion. The stiffness k can be estimated through linear regression by measuring the trapping force (Ftrapping) corresponding to the displacement (x) of a droplet from the trap center. By plotting Ftrapping – x curves for certain values of Vin (22/38/54 Vpp) at DTF = 10
Turbulence and turbulent drag reduction in swirling flow: Inertial versus viscous forcing
NASA Astrophysics Data System (ADS)
Burnishev, Yuri; Steinberg, Victor
2015-08-01
We report unexpected results of a drastic difference in the transition to fully developed turbulent and turbulent drag reduction (TDR) regimes and in their properties in a von Karman swirling flow with counter-rotating disks of water-based polymer solutions for viscous (by smooth disks) as well as inertial (by bladed disks) forcing and by tracking just torque Γ (t ) and pressure p (t ) . For the viscous forcing, just a single TDR regime is found with the transition values of the Reynolds number (Re) Recturb=RecTDR≃(4.8 ±0.2 ) ×105 independent of ϕ , whereas for the inertial forcing two turbulent regimes are revealed. The first transition is to fully developed turbulence, and the second one is to the TDR regime with both Recturb and RecTDR depending on polymer concentration ϕ . Both regimes differ by the values of Cf and Cp, by the scaling exponents of the fundamental turbulent characteristics, by the nonmonotonic dependencies of skewness and flatness of the pressure PDFs on Re, and by the different frequency power spectra of p with the different dependencies of the main vortex peak frequency in the p power spectra on ϕ and Re. Thus our experimental results show the transition to the TDR regime in a von Karman swirling flow for the viscous and inertial forcings in a sharp contrast to the recent experiments [Phys. Fluids 10, 426 (1998), 10.1063/1.869532; Phys. Rev. E 47, R28(R) (1993), 10.1103/PhysRevE.47.R28; and J. Phys.: Condens. Matter 17, S1195 (2005), 10.1088/0953-8984/17/14/008] where the transition to TDR is observed in the same swirling flow with counter-rotating disks only for the viscous forcing. The latter result has led its authors to the wrong conclusion that TDR is a solely boundary effect contrary to the inertial forcing associated with the bulk effect, and this conception is currently rather widely accepted in literature.
NASA Astrophysics Data System (ADS)
Madanu, Sushma B.; Barbel, Stanley I.; Ward, Thomas
2016-06-01
In this paper, transverse vibrations of an electrostatically actuated thin flexible cantilever perturbed by low-speed air flow are studied using both experiments and numerical modeling. In the experiments, the dynamic characteristics of the cantilever are studied by supplying a DC voltage with an AC component for electrostatic forcing and a constant uniform air flow around the cantilever system for aerodynamic forcing. A range of control parameters leading to stable vibrations are established using a dimensionless operating parameter that is the ratio of the induced and the free stream velocities. Numerical results are validated with experimental data. Assuming the amplitude of vibrations are small, then a non-linear dynamic Euler-Bernoulli beam equation with viscous damping and gravitational effects is used to model the equation of motion. Aerodynamic forcing is modelled as a temporally sinusoidal and uniform force acting perpendicular to the beam length. The forcing amplitude is found to be proportional to the square of the air flow velocity. Numerical results strongly agree with the experiments predicting accurate vibration amplitude, displacement frequency, and quasi-periodic displacement of the cantilever tip.
Madanu, Sushma B; Barbel, Stanley I; Ward, Thomas
2016-06-01
In this paper, transverse vibrations of an electrostatically actuated thin flexible cantilever perturbed by low-speed air flow are studied using both experiments and numerical modeling. In the experiments, the dynamic characteristics of the cantilever are studied by supplying a DC voltage with an AC component for electrostatic forcing and a constant uniform air flow around the cantilever system for aerodynamic forcing. A range of control parameters leading to stable vibrations are established using a dimensionless operating parameter that is the ratio of the induced and the free stream velocities. Numerical results are validated with experimental data. Assuming the amplitude of vibrations are small, then a non-linear dynamic Euler-Bernoulli beam equation with viscous damping and gravitational effects is used to model the equation of motion. Aerodynamic forcing is modelled as a temporally sinusoidal and uniform force acting perpendicular to the beam length. The forcing amplitude is found to be proportional to the square of the air flow velocity. Numerical results strongly agree with the experiments predicting accurate vibration amplitude, displacement frequency, and quasi-periodic displacement of the cantilever tip. PMID:27368778
NASA Astrophysics Data System (ADS)
Madanu, Sushma Bala
Transverse vibrations of an electrostatically actuated thin flexible cantilever perturbed by low-speed air flow is studied using both experiments and numerical modeling. In the experiments the dynamic characteristics of the cantilever are studied by supplying a DC voltage with an AC component for electrostatic forcing and a constant uniform air flow around the cantilever system for aerodynamic forcing. The maximum voltage applied varies from 1 - 9 kV and air flow speeds range from 0.224 - 3.58 m/s (0.5 - 8 mile/hr). The Reynolds numbers for these speeds lie in the range of 1000 - 20000. A range of control parameters leading to stable vibrations are established using the Strouhal number as the operating parameter whose inverse values change from 100 - 2500. The Numerical results are validated with experimental results. Assuming the amplitude of vibrations are small, then a non-linear dynamic Euler-Bernoulli beam equation with viscous damping and gravitational effects is used to model the vibrations of the dynamical system. Aerodynamic forcing is modeled as a temporally sinusoidal and uniform force acting perpendicular to the beam length. The forcing amplitude is found to be proportional to square of air flow velocity by obtaining relationship between the experimental amplitude of vibrations and air flow velocity. Numerical results strongly agree with those of experiments predicting accurate vibration amplitudes, displacement frequency and quasi-periodic displacements of the cantilever tip.
NASA Technical Reports Server (NTRS)
Karpel, M.
1994-01-01
Various control analysis, design, and simulation techniques of aeroservoelastic systems require the equations of motion to be cast in a linear, time-invariant state-space form. In order to account for unsteady aerodynamics, rational function approximations must be obtained to represent them in the first order equations of the state-space formulation. A computer program, MIST, has been developed which determines minimum-state approximations of the coefficient matrices of the unsteady aerodynamic forces. The Minimum-State Method facilitates the design of lower-order control systems, analysis of control system performance, and near real-time simulation of aeroservoelastic phenomena such as the outboard-wing acceleration response to gust velocity. Engineers using this program will be able to calculate minimum-state rational approximations of the generalized unsteady aerodynamic forces. Using the Minimum-State formulation of the state-space equations, they will be able to obtain state-space models with good open-loop characteristics while reducing the number of aerodynamic equations by an order of magnitude more than traditional approaches. These low-order state-space mathematical models are good for design and simulation of aeroservoelastic systems. The computer program, MIST, accepts tabular values of the generalized aerodynamic forces over a set of reduced frequencies. It then determines approximations to these tabular data in the LaPlace domain using rational functions. MIST provides the capability to select the denominator coefficients in the rational approximations, to selectably constrain the approximations without increasing the problem size, and to determine and emphasize critical frequency ranges in determining the approximations. MIST has been written to allow two types data weighting options. The first weighting is a traditional normalization of the aerodynamic data to the maximum unit value of each aerodynamic coefficient. The second allows weighting the
Application of CAD/CAE class systems to aerodynamic analysis of electric race cars
NASA Astrophysics Data System (ADS)
Grabowski, L.; Baier, A.; Buchacz, A.; Majzner, M.; Sobek, M.
2015-11-01
Aerodynamics is one of the most important factors which influence on every aspect of a design of a car and car driving parameters. The biggest influence aerodynamics has on design of a shape of a race car body, especially when the main objective of the race is the longest distance driven in period of time, which can not be achieved without low energy consumption and low drag of a car. Designing shape of the vehicle body that must generate the lowest possible drag force, without compromising the other parameters of the drive. In the article entitled „Application of CAD/CAE class systems to aerodynamic analysis of electric race cars” are being presented problems solved by computer analysis of cars aerodynamics and free form modelling. Analysis have been subjected to existing race car of a Silesian Greenpower Race Team. On a basis of results of analysis of existence of Kammback aerodynamic effect innovative car body were modeled. Afterwards aerodynamic analysis were performed to verify existence of aerodynamic effect for innovative shape and to recognize aerodynamics parameters of the shape. Analysis results in the values of coefficients and aerodynamic drag forces. The resulting drag forces Fx, drag coefficients Cx(Cd) and aerodynamic factors Cx*A allowed to compare all of the shapes to each other. Pressure distribution, air velocities and streams courses were useful in determining aerodynamic features of analyzed shape. For aerodynamic tests was used Ansys Fluent CFD software. In a paper the ways of surface modeling with usage of Realize Shape module and classic surface modeling were presented. For shapes modeling Siemens NX 9.0 software was used. Obtained results were used to estimation of existing shapes and to make appropriate conclusions.
NASA Astrophysics Data System (ADS)
Patacchini, Leonardo; Hutchinson, Ian H.
2007-11-01
The interaction of a spherical object with a collisionless plasma under weakly magnetized conditions is investigated by means of the PIC code SCEPTIC [1]. The key features of this 2D3v electrostatic ion kinetic code are a spherical geometry accurately resolving the collector's edge, and a Boltzmann treatment of the electrons, whose current is calculated using a recently developed empirical formula accounting for their magnetization [2]. By asymmetrically reducing the ion and electron fluxes to the collector, the magnetic field (B) has a strong influence on the floating potential (φf). The non monotonic dependence of φf on B is documented for a wide range of plasma parameters relevant to probes and dust particles. The magnetic field is also shown to reduce the ion focusing effects present in an unmagnetized plasma when the drift velocity is non negligible, thus the electrostatic part of the ion drag force. This effect is compared with the variation of the electron-ion Coulomb collision frequency with the local magnetic field.[1] I.H. Hutchinson PPCF 47, 71-87 (2005)[2] L. Patacchini et al. Phys. Plasma 14, 062111 (2007)
The aerodynamic forces and pressure distribution of a revolving pigeon wing
Usherwood, James R.
2012-01-01
The aerodynamic forces acting on a revolving dried pigeon wing and a flat card replica were measured with a propeller rig, effectively simulating a wing in continual downstroke. Two methods were adopted: direct measurement of the reaction vertical force and torque via a forceplate, and a map of the pressures along and across the wing measured with differential pressure sensors. Wings were tested at Reynolds numbers up to 108,000, typical for slow-flying pigeons, and considerably above previous similar measurements applied to insect and hummingbird wing and wing models. The pigeon wing out-performed the flat card replica, reaching lift coefficients of 1.64 compared with 1.44. Both real and model wings achieved much higher maximum lift coefficients, and at much higher geometric angles of attack (43°), than would be expected from wings tested in a windtunnel simulating translating flight. It therefore appears that some high-lift mechanisms, possibly analogous to those of slow-flying insects, may be available for birds flapping with wings at high angles of attack. The net magnitude and orientation of aerodynamic forces acting on a revolving pigeon wing can be determined from the differential pressure maps with a moderate degree of precision. With increasing angle of attack, variability in the pressure signals suddenly increases at an angle of attack between 33° and 38°, close to the angle of highest vertical force coefficient or lift coefficient; stall appears to be delayed compared with measurements from wings in windtunnels. PMID:22736891
The aerodynamic forces and pressure distribution of a revolving pigeon wing
NASA Astrophysics Data System (ADS)
Usherwood, James R.
The aerodynamic forces acting on a revolving dried pigeon wing and a flat card replica were measured with a propeller rig, effectively simulating a wing in continual downstroke. Two methods were adopted: direct measurement of the reaction vertical force and torque via a forceplate, and a map of the pressures along and across the wing measured with differential pressure sensors. Wings were tested at Reynolds numbers up to 108,000, typical for slow-flying pigeons, and considerably above previous similar measurements applied to insect and hummingbird wing and wing models. The pigeon wing out-performed the flat card replica, reaching lift coefficients of 1.64 compared with 1.44. Both real and model wings achieved much higher maximum lift coefficients, and at much higher geometric angles of attack (43°), than would be expected from wings tested in a windtunnel simulating translating flight. It therefore appears that some high-lift mechanisms, possibly analogous to those of slow-flying insects, may be available for birds flapping with wings at high angles of attack. The net magnitude and orientation of aerodynamic forces acting on a revolving pigeon wing can be determined from the differential pressure maps with a moderate degree of precision. With increasing angle of attack, variability in the pressure signals suddenly increases at an angle of attack between 33° and 38°, close to the angle of highest vertical force coefficient or lift coefficient; stall appears to be delayed compared with measurements from wings in windtunnels.
The aerodynamic forces and pressure distribution of a revolving pigeon wing
NASA Astrophysics Data System (ADS)
Usherwood, James R.
2009-05-01
The aerodynamic forces acting on a revolving dried pigeon wing and a flat card replica were measured with a propeller rig, effectively simulating a wing in continual downstroke. Two methods were adopted: direct measurement of the reaction vertical force and torque via a forceplate, and a map of the pressures along and across the wing measured with differential pressure sensors. Wings were tested at Reynolds numbers up to 108,000, typical for slow-flying pigeons, and considerably above previous similar measurements applied to insect and hummingbird wing and wing models. The pigeon wing out-performed the flat card replica, reaching lift coefficients of 1.64 compared with 1.44. Both real and model wings achieved much higher maximum lift coefficients, and at much higher geometric angles of attack (43°), than would be expected from wings tested in a windtunnel simulating translating flight. It therefore appears that some high-lift mechanisms, possibly analogous to those of slow-flying insects, may be available for birds flapping with wings at high angles of attack. The net magnitude and orientation of aerodynamic forces acting on a revolving pigeon wing can be determined from the differential pressure maps with a moderate degree of precision. With increasing angle of attack, variability in the pressure signals suddenly increases at an angle of attack between 33° and 38°, close to the angle of highest vertical force coefficient or lift coefficient; stall appears to be delayed compared with measurements from wings in windtunnels.
On drag and lift forces in two-dimensional flows of a particulate mixture: A theoretical study
Massoudi, M.
2006-06-01
In this paper we propose and derive expressions for the drag and lift forces in a two-phase particulate mixture. The analysis is limited to two-dimensional laminar flows. In the Section after the Introduction, a brief review of the single particle approach is provided; it is then shown that in most multiphase flow problems some generalization of these forces acting on a single particle is used. We then describe a different way of defining the lift force and the drag force, an approach used in non-Newtonian fluid mechanics. In the following Section, the essential equations of Mixture Theory are provided and the specific approach of [1] is used. In this scheme, the lift force is part of the interaction mechanisms, which are to be modeled as constitutive parameters. In the final Section, we derive an expression for the lift force, whereby it is shown that the normal component of the force acting on the body, obtained by integrating the traction vector of the mixture acting on a single isolated particle, will give us the desired expression for the lift force in multi-component flows.
NASA Astrophysics Data System (ADS)
Patacchini, Leonardo; Hutchinson, Ian H.
2008-07-01
The ion drag force on a spherical dust particle immersed in a flowing plasma with an external electric field is self-consistently calculated using the particle-in-cell code SCEPTIC in the entire range of charge-exchange collisionality. Our results, not based on questionable approximations, extend prior analytic calculations valid only in a few limiting regimes. Particular attention is given to the force direction, shown never to be directed opposite to the flow except in the continuum limit, where other forces are of a much stronger magnitude.
Patacchini, Leonardo; Hutchinson, Ian H.
2008-07-11
The ion drag force on a spherical dust particle immersed in a flowing plasma with an external electric field is self-consistently calculated using the particle-in-cell code SCEPTIC in the entire range of charge-exchange collisionality. Our results, not based on questionable approximations, extend prior analytic calculations valid only in a few limiting regimes. Particular attention is given to the force direction, shown never to be directed opposite to the flow except in the continuum limit, where other forces are of a much stronger magnitude.
Measuring the Effects of Lift and Drag on Projectile Motion
ERIC Educational Resources Information Center
Cross, Rod
2012-01-01
The trajectory of a projectile through the air is affected both by gravity and by aerodynamic forces. The latter forces can conveniently be ignored in many situations, even when they are comparatively large. For example, if a 145-g, 74-mm diameter baseball is pitched at 40 ms[superscript -1] (89.5 mph), it experiences a drag force of about 1.5 N.…
Investigation on the forced response of a radial turbine under aerodynamic excitations
NASA Astrophysics Data System (ADS)
Ma, Chaochen; Huang, Zhi; Qi, Mingxu
2016-04-01
Rotor blades in a radial turbine with nozzle guide vanes typically experience harmonic aerodynamic excitations due to the rotor stator interaction. Dynamic stresses induced by the harmonic excitations can result in high cycle fatigue (HCF) of the blades. A reliable prediction method for forced response issue is essential to avoid the HCF problem. In this work, the forced response mechanisms were investigated based on a fluid structure interaction (FSI) method. Aerodynamic excitations were obtained by three-dimensional unsteady computational fluid dynamics (CFD) simulation with phase shifted periodic boundary conditions. The first two harmonic pressures were determined as the primary components of the excitation and applied to finite element (FE) model to conduct the computational structural dynamics (CSD) simulation. The computed results from the harmonic forced response analysis show good agreement with the predictions of Singh's advanced frequency evaluation (SAFE) diagram. Moreover, the mode superposition method used in FE simulation offers an efficient way to provide quantitative assessments of mode response levels and resonant strength.
Aerodynamic force measurements with a strain-gage balance in a cryogenic wind tunnel
NASA Technical Reports Server (NTRS)
Boyden, R. P.; Johnson, W. G., Jr.; Ferris, A. T.
1983-01-01
Aerodynamic force measurements on a generalized 75 deg delta wing model with sharp leading edges were made with a three component internal strain gage balance in a cryogenic wind tunnel at stagnation temperatures of 300 K, 200 K, and 110 K. The feasibility of using a strain gage balance without thermal control in a cryogenic environment as well as the use of electrical resistance heaters, an insulator between the model and the balance, and a convection shield on the balance was investigated. Force and moment data on the delta wing model as measured by the balance are compared at the different temperatures while holding constant either the Reynolds number or the tunnel stagnation pressure. Tests were made at Mach numbers of 0.3 and 0.5 and at angles of attack up to 29 deg. The results indicate that it is feasible to acquire accurate force and moment data while operating at steady state thermal conditions in a cryogenic wind tunnel, either with or without electrical heaters on the balance. Within the limits of the balance accuracy, there were no apparent Reynolds number effects on the aerodynamic results for the delta wind model.
Li, Zhigang; Wang, Hai
2003-12-01
The transport of small particles in the free-molecule regime is investigated on the basis of gas kinetic theory. Drag force formulations were derived in two limiting collision models-namely, specular and diffuse scattering-by considering the potential force of interactions between the particle and fluid molecules. A parametrized drag coefficient equation is proposed and accounts for the transition from specular to diffuse scattering as particle size exceeds a critical value. The resulting formulations are shown to be consistent with the Chapman-Enskog theory of molecular diffusion. In the limit of rigid-body interactions, these formulations can be simplified also to Epstein's solutions [P. S. Epstein, Phys. Rev. 23, 710 (1924)]. PMID:14754191
NASA Technical Reports Server (NTRS)
Holmes, Bruce J.; Schairer, Edward; Hicks, Gary; Wander, Stephen; Blankson, Isiaiah; Rose, Raymond; Olson, Lawrence; Unger, George
1990-01-01
Presented here is a comprehensive review of the following aerodynamics elements: computational methods and applications, computational fluid dynamics (CFD) validation, transition and turbulence physics, numerical aerodynamic simulation, drag reduction, test techniques and instrumentation, configuration aerodynamics, aeroacoustics, aerothermodynamics, hypersonics, subsonic transport/commuter aviation, fighter/attack aircraft and rotorcraft.
Aerodynamic design of a Coanda induced force and thruster anti-torque system
NASA Technical Reports Server (NTRS)
Velkoff, Henry R.; Tung, Chee
1991-01-01
A general method of analysis of the external and internal aerodynamics of a generic Coanda induced circulation anti-torque system is presented. The technique gives moment about the yaw axis and download induced on the boom as well as the force developed by an aft jet. The external flows including downwash, wake swirl and the boom circulation are considered. The internal flow and losses through the duct, fan, blown slots, cascades and nozzle are considered on a step-by-step basis. Limited comparison is made with open data where available.
Analysis of preflutter and postflutter characteristics with motion-matched aerodynamic forces
NASA Technical Reports Server (NTRS)
Cunningham, H. J.
1978-01-01
The development of the equations of dynamic equilibrium for a lifting surface from Lagrange's equation is reviewed and restated for general exponential growing and decaying oscillatory motion. Aerodynamic forces for this motion are obtained from the three-dimensional supersonic kernel function that is newly generalized to complex reduced frequencies. Illustrative calculations were made for two flutter models at supersonic Mach numbers. Preflutter and postflutter motion isodecrement curves were obtained. This type of analysis can be used to predict preflutter behavior during flutter testing and to predict postflutter behavior for use in the design of flutter suppression systems.
Measuring the Effects of Lift and Drag on Projectile Motion
NASA Astrophysics Data System (ADS)
Cross, Rod
2012-02-01
The trajectory of a projectile through the air is affected both by gravity and by aerodynamic forces. The latter forces can conveniently be ignored in many situations, even when they are comparatively large. For example, if a 145-g, 74-mm diameter baseball is pitched at 40 ms-1 (89.5 mph), it experiences a drag force of about 1.5 N. The gravitational force on the ball 1.42 N. Nevertheless, the trajectory of a baseball pitched without spin is not strongly affected by the drag force. Because the ball is relatively heavy and the flight distance is relatively small (about 60 ft), the drag force reduces the ball speed by only about 10% by the time it reaches the batter. As a result, the time taken for the ball to reach the batter is only about 5% longer than in a vacuum, and the actual trajectory is also very similar.2
NASA Technical Reports Server (NTRS)
Catalina, Adrian V.; Stefanescu, Doru M.; Sen, Subhayu
2000-01-01
The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. Whether a particle will be engulfed or continuously pushed by SLI is essentially determined by the balance of forces acting on the particle. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that not only the steady-state approach is inappropriate to model the interaction process but also that even at steady-state the theoretical solution underestimates the drag force. A regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gave a relationship of the form F(sub d) (exp num) = (square root of 3) pi eta V(sub p)((R(sub p) / d) (exp 10 gamma/3)) as compared to the theoretical solution F(sub d) (exp theor) = 3 X (square root of 2) pi eta V(sub p)((R(sub p) / d) (exp 3/2)) where F(sub d) is the drag force, eta is the dynamic viscosity of the fluid, V(sub p) is the particle velocity, R(sub p) is the particle radius, gamma is Euler's constant (gamma is approximately equal to 0.577), and d is the width of the gap between the particle and the SLI. Model validation as well as the influence of the interface shape on the value of F(sub d) will also be discussed.
Simultaneous measurement of aerodynamic forces and kinematics in flapping wings of tethered locust.
Shkarayev, Sergey; Kumar, Rajeev
2015-12-01
Aerodynamic and inertial forces and corresponding kinematics of flapping wings of locusts, Schistocerca americana, were investigated in a low-speed wind tunnel. The experimental setup included live locusts mounted on microbalance synchronized with a high-speed video system. Simultaneous measurements of wing kinematics and forces were carried out on three locusts at 7° angle of attack and velocities of 0 m s(-1) and 4 m s(-1). Time variations of flapping and pitching angles exhibit similar patterns in fore- and hindwings and among the animals. Significant tip to root variations in pitching angle are found in both wings. The locusts have much larger flapping and pitching amplitudes in still air causing larger oscillations in inertial forces. Inertial forces are added to the lift and thrust on one part of the stroke, resulting in higher reaction forces and subtracted on the other part. Plots of the lift demonstrate similar trends with and without the wind. The global maxima and peak-to-peak amplitudes in lift are about the same in both tests. However, local minima are significantly lower in still air, resulting in much smaller stroke-averaged lift. Amplitudes of thrust force oscillations are much higher in still air; consequently, the stroke-averaged thrust is higher compared to the non-zero freestream velocity case. PMID:26496206
Helicopter hub fairing and pylon interference drag
NASA Technical Reports Server (NTRS)
Graham, D. R.; Sung, D. Y.; Young, L. A.; Louie, A. W.; Stroub, R. H.
1989-01-01
A wind tunnel test was conducted to study the aerodynamics of helicopter hub and pylon fairings. The test was conducted in the 7-by 10 Foot Subsonic Wind Tunnel (Number 2) at Ames Research Center using a 1/5-scale XH-59A fuselage model. The primary focus of the test was on the rotor hub fairing and pylon mutual interference drag. Parametric studies of pylon and hub fairing geometry were also conducted. This report presents the major findings of the test as well as tabulated force and moment data, flow visualization photographs, and graphical presentations of the drag data. The test results indicate that substantial drag reduction can be attained through the use of a cambered hub fairing with circular arc upper surface and flat lower surface. Furthermore, a considerable portion of the overall drag reduction is attributed to the reduction in the hub-on-pylon interference drag. It is also observed that the lower surface curvature of the fairing has a strong influence on the hub fairing and on pylon interference drag. However, the drag reduction benefit that was obtained by using the cambered hub fairing with a flat lower surface was adversely affected by the clearance between the hub fairing and the pylon.
Comparing the drag force on heavy quarks in N=4 super-Yang-Mills theory and QCD
Gubser, Steven S.
2007-12-15
Computations of the drag force on a heavy quark moving through a thermal state of strongly coupled N=4 super-Yang-Mills theory have appeared recently. I compare the strength of this effect between N=4 gauge theory and QCD, using the static force between external quarks to normalize the 't Hooft coupling. Comparing N=4 and QCD at fixed energy density then leads to a relaxation time of roughly 2 fm/c for charm quarks moving through a quark-gluon plasma at T=250 MeV. This estimate should be regarded as preliminary because of the difficulties of comparing two such different theories.
Analysis of Dragonfly Take-off Mechanism: Initial Impulse Generated by Aerodynamic Forces
NASA Astrophysics Data System (ADS)
Zhu, Ruijie; Bode-Oke, Ayodeji; Ren, Yan; Dong, Haibo; Flow Simulation Research Team
2013-11-01
Take-off is a critical part of insect flight due to not only that every single flight initiates from take-off, but also that the take-off period, despite its short duration, accounts for a relatively large fraction of the total energy consumption. Thus, studying the mechanism of insect take-off will help to improve the design of Micro Air Vehicles (MAVs) in two major properties, the success rate and the energy efficiency of take-off. In this work, we study 20 cases in which dragonflies (species including Pachydiplax longipennis, Epitheca Cynosura, Epitheca princeps etc.) take off from designed platform. By high-speed photogrammetry, 3-d reconstruction and numerical simulation, we explore how dragonflies coordinate different body parts to help take-off. We evaluate how aerodynamic forces generated by wing flapping create the initial impulse, and how these forces help save energy consumption. Supported by NSF CBET-1343154.
NASA Technical Reports Server (NTRS)
Catalina, Adrian V.; Stefanescu, Doru M.; Sen, Subhayu
2000-01-01
The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: Abstract The distribution of insoluble particles in a metal casting depends primarily on the interaction of the particles with the solid/liquid interface (SLI) during the solidification process. The balance of the forces acting on the particle essentially determines whether a particle will be engulfed or pushed by the SLI. An important component of this force balance is the drag force generated by the particle motion in front of the SLI. Previously developed mathematical models for particle/SLI interaction made use of steady-state solutions of this force provided by the lubrication theory. However, our numerical model based on the SLI tracking approach shows that the steady-state approach is inappropriate to model the interaction process and that at steady-state the theoretical solution underestimates the drag force. It was found that regression analysis of steady-state numerical solutions for cylindrical particles moving normal to a flat SLI gives a relationship of the form: F(sub D, sup num) =sqoare
Cruise aerodynamics of USB nacelle/wing geometric variations
NASA Technical Reports Server (NTRS)
Braden, J. A.; Hancock, J. P.; Burdges, K. P.
1976-01-01
Experimental results are presented on aerodynamic effects of geometric variations in upper surface blown nacelle configurations at high speed cruise conditions. Test data include both force and pressure measurements on two and three dimensional models powered by upper surface blowing nacelles of varying geometries. Experimental results are provided on variations in nozzle aspect ratio, nozzle boattail angle, and multiple nacelle installations. The nacelles are ranked according to aerodynamic drag penalties as well as overall installed drag penalties. Sample effects and correlations are shown for data obtained with the pressure model.
NASA Technical Reports Server (NTRS)
Ramsey, P. E.
1972-01-01
Experimental aerodynamic investigations were conducted in the NASA/MSFC 14-inch Trisonic Wind Tunnel from Sept. 27 to Oct. 7, 1972 on a 0.004 scale model of the NR ATP baseline shuttle orbiter configuration. Six component aerodynamic force and moment data were recorded at 0 deg sideslip angle over an angle of attack range from 0 to 20 deg for Mach numbers of 0.6 to 4.96, 20 to 40 deg for Mach numbers of 0.6, 0.9, 2.99, and 4.96, and 40 to 60 deg for Mach numbers of 2.99 and 4.96. Data were obtained over a sideslip range of -10 to 10 deg at 0, 10, and 20 deg angles of attack over the Mach range and 30 and 50 deg at Mach numbers of 2.99 and 4.96. The purpose of the test was to define the buildup, performance, stability, and control characteristics of the orbiter configuration. The model parameters, were: body alone; body-wing; body-wing-tail; elevon deflections of 0, 10, -20, and -40 deg both full and split); aileron deflections of plus or minus 10 deg (full and split); rudder flares of 10 and 40 deg, and a rudder deflection of 15 deg about the 10 and 40 deg flare positions.
NASA Technical Reports Server (NTRS)
Tiffany, Sherwood H.; Adams, William M., Jr.
1988-01-01
The approximation of unsteady generalized aerodynamic forces in the equations of motion of a flexible aircraft are discussed. Two methods of formulating these approximations are extended to include the same flexibility in constraining the approximations and the same methodology in optimizing nonlinear parameters as another currently used extended least-squares method. Optimal selection of nonlinear parameters is made in each of the three methods by use of the same nonlinear, nongradient optimizer. The objective of the nonlinear optimization is to obtain rational approximations to the unsteady aerodynamics whose state-space realization is lower order than that required when no optimization of the nonlinear terms is performed. The free linear parameters are determined using the least-squares matrix techniques of a Lagrange multiplier formulation of an objective function which incorporates selected linear equality constraints. State-space mathematical models resulting from different approaches are described and results are presented that show comparative evaluations from application of each of the extended methods to a numerical example.
NASA Technical Reports Server (NTRS)
Henderson, Gregory H.; Fleeter, Sanford
1992-01-01
The paper investigates the fundamental gust modeling assumption on the basis of a series of experiments performed in the Purdue Annular Cascade Research Facility. The unsteady period flow field is generated by rotating flows of perforated plates and airfoil cascades, with the resulting unsteady periodic chordwise pressure response of a downstream low solidity stator row determined by miniature pressure transducers embedded within selected airfoils. When the forcing function exhibited the characteristics of a linear-theory gust, the resulting response on the downstream stator airfoils was in excellent agreement with the linear-theory models. When the forcing function did not exhibit linear-theory gust characteristics, the resulting unsteady aerodynamic response of the downstream stators was much more complex and correlated poorly with the linear-theory gust predictions. It is shown that the forcing function generator significantly affects the resulting gust response, with the complexity of the response characteristics increasing from the perforated-plate to the airfoil-cascade forcing functions.
NASA Astrophysics Data System (ADS)
Li, Longqiu; Wang, Jiyuan; Li, Tianlong; Song, Wenping; Zhang, Guangyu
2015-03-01
Motion of catalytic micro/nano-motors with various geometries is mainly determined by the drag force and the propulsion force acting on the motors as they move in low Reynolds number flows. A unified solution of drag force along with drag coefficient for all circular cross-sectional types of micro/nano-motors is derived. The effect of the geometric parameters of a micro/nano-motor, such as the semi-cone angle θ, the ratio ξ of length to larger radius, on the drag coefficient is identified. Results provided in this work are useful for optimizing the design and fabrication of catalytic micro/nano-motors, which can be potentially used in biomedical and environmental engineering.
Bimbard, Gaëlle; Kolomenskiy, Dmitry; Bouteleux, Olivier; Casas, Jérôme; Godoy-Diana, Ramiro
2013-09-15
Up to now, the take-off stage has remained an elusive phase of insect flight that was relatively poorly explored compared with other maneuvers. An overall assessment of the different mechanisms involved in force production during take-off has never been explored. Focusing on the first downstroke, we have addressed this problem from a force balance perspective in butterflies taking off from the ground. In order to determine whether the sole aerodynamic wing force could explain the observed motion of the insect, we have firstly compared a simple analytical model of the wing force with the acceleration of the insect's center of mass estimated from video tracking of the wing and body motions. Secondly, wing kinematics were also used for numerical simulations of the aerodynamic flow field. Similar wing aerodynamic forces were obtained by the two methods. However, neither are sufficient, nor is the inclusion of the ground effect, to predict faithfully the body acceleration. We have to resort to the leg forces to obtain a model that best fits the data. We show that the median and hind legs display an active extension responsible for the initiation of the upward motion of the insect's body, occurring before the onset of the wing downstroke. We estimate that legs generate, at various times, an upward force that can be much larger than all other forces applied to the insect's body. The relative timing of leg and wing forces explains the large variability of trajectories observed during the maneuvers. PMID:23788714
NASA Astrophysics Data System (ADS)
Danby, J. M. A.
If the restricted problem of three bodies is modified so that the third body experiences a drag force proportional to its velocity relative to a surrounding medium which is modelled so that the triangular points remain equilibria, then, in a linear analysis these points are unstable. The long-period oscillations become associated with an exponential factor eat with positive a. This has been confirmed by numerical integration of the complete nonlinear equations. Variations in the kinematics of the surrounding medium and in its density are also considered: the instability remains.
Van Truong, Tien; Byun, Doyoung; Kim, Min Jun; Yoon, Kwang Joon; Park, Hoon Cheol
2013-09-01
The aim of this work is to provide an insight into the aerodynamic performance of the beetle during takeoff, which has been estimated in previous investigations. We employed a scaled-up electromechanical model flapping wing to measure the aerodynamic forces and the three-dimensional flow structures on the flapping wing. The ground effect on the unsteady forces and flow structures were also characterized. The dynamically scaled wing model could replicate the general stroke pattern of the beetle's hind wing kinematics during takeoff flight. Two wing kinematic models have been studied to examine the influences of wing kinematics on unsteady aerodynamic forces. In the first model, the angle of attack is asymmetric and varies during the translational motion, which is the flapping motion of the beetle's hind wing. In the second model, the angle of attack is constant during the translational motion. The instantaneous aerodynamic forces were measured for four strokes during the beetle's takeoff by the force sensor attached at the wing base. Flow visualization provided a general picture of the evolution of the three-dimensional leading edge vortex (LEV) on the beetle hind wing model. The LEV is stable during each stroke, and increases radically from the root to the tip, forming a leading-edge spiral vortex. The force measurement results show that the vertical force generated by the hind wing is large enough to lift the beetle. For the beetle hind wing kinematics, the total vertical force production increases 18.4% and 8.6% for the first and second strokes, respectively, due to the ground effect. However, for the model with a constant angle of attack during translation, the vertical force is reduced during the first stroke. During the third and fourth strokes, the ground effect is negligible for both wing kinematic patterns. This finding suggests that the beetle's flapping mechanism induces a ground effect that can efficiently lift its body from the ground during takeoff
Simultaneous drag and flow measurements of Olympic skeleton athletes
NASA Astrophysics Data System (ADS)
Moon, Yae Eun; Digiulio, David; Peters, Steve; Wei, Timothy
2009-11-01
The Olympic sport of skeleton involves an athlete riding a small sled face first down a bobsled track at speeds up to 130 km/hr. In these races, the difference between gold and missing the medal stand altogether can be hundredths of a second per run. As such, reducing aerodynamic drag through proper body positioning is of first order importance. To better study the flow behavior and to improve the performance of the athletes, we constructed a static force balance system on a mock section of a bobsled track. Athlete and the sled are placed on the force balance system which is positioned at the exit of an open loop wind tunnel. Simultaneous drag force and DPIV velocity field measurements were made along with video recordings of body position to aid the athletes in determining their optimal aerodynamic body position.
Not Available
1993-01-01
In this article two integral computational fluid dynamics methods for steady-state and transient vehicle aerodynamic simulations are described using a Chevrolet Corvette ZR-1 surface panel model. In the last decade, road-vehicle aerodynamics have become an important design consideration. Originally, the design of low-drag shapes was given high priority due to worldwide fuel shortages that occurred in the mid-seventies. More recently, there has been increased interest in the role aerodynamics play in vehicle stability and passenger safety. Consequently, transient aerodynamics and the aerodynamics of vehicle in yaw have become important issues at the design stage. While there has been tremendous progress in Navier-Stokes methodology in the last few years, the physics of bluff-body aerodynamics are still very difficult to model correctly. Moreover, the computational effort to perform Navier-Stokes simulations from the geometric stage to complete flow solutions requires much computer time and impacts the design cycle time. In the short run, therefore, simpler methods must be used for such complicated problems. Here, two methods are described for the simulation of steady-state and transient vehicle aerodynamics.
Ikkurthi, V. R.; Matyash, K.; Schneider, R.; Melzer, A.
2010-10-15
Charging of multiple spherical dust grains located in presheath and sheath regions of an rf discharge has been studied using a three-dimensional particle-particle-particle-mesh (P{sup 3}M) code. First, dust charge, potential, and ion drag force on two dust particles for various interparticle separations are computed. It is found that for dust separations larger than the shielding length the dust parameters for the two dust particles match with the single particle values. As the dust separation is equal to or less than the shielding length, the transverse component of ion force increases which is due to dynamic shielding effect caused by neighboring dust particle. However, dust charge, potential, and ion drag are found not to be affected considerably. Further, dust charge and potential on an arrangement of nine dust particles are computed. The dust charge and potential do not differ much from the single particle values for the presheath. However the dust charges of multiple dust particles in the sheath are much less negative compared to the single dust case which is shown to be due to ion focusing.
Bulushev, Roman D; Marion, Sanjin; Radenovic, Aleksandra
2015-10-14
Combination of glass nanocapillaries with optical tweezers allowed us to detect DNA-protein complexes in physiological conditions. In this system, a protein bound to DNA is characterized by a simultaneous change of the force and ionic current signals from the level observed for the bare DNA. Controlled displacement of the protein away from the nanocapillary opening revealed decay in the values of the force and ionic current. Negatively charged proteins EcoRI, RecA, and RNA polymerase formed complexes with DNA that experienced electrophoretic force lower than the bare DNA inside nanocapillaries. Force profiles obtained for DNA-RecA in our system were different than those in the system with nanopores in membranes and optical tweezers. We suggest that such behavior is due to the dominant impact of the drag force comparing to the electrostatic force acting on a DNA-protein complex inside nanocapillaries. We explained our results using a stochastic model taking into account the conical shape of glass nanocapillaries. PMID:26393370
Distributed Aerodynamic Sensing and Processing Toolbox
NASA Technical Reports Server (NTRS)
Brenner, Martin; Jutte, Christine; Mangalam, Arun
2011-01-01
A Distributed Aerodynamic Sensing and Processing (DASP) toolbox was designed and fabricated for flight test applications with an Aerostructures Test Wing (ATW) mounted under the fuselage of an F-15B on the Flight Test Fixture (FTF). DASP monitors and processes the aerodynamics with the structural dynamics using nonintrusive, surface-mounted, hot-film sensing. This aerodynamic measurement tool benefits programs devoted to static/dynamic load alleviation, body freedom flutter suppression, buffet control, improvement of aerodynamic efficiency through cruise control, supersonic wave drag reduction through shock control, etc. This DASP toolbox measures local and global unsteady aerodynamic load distribution with distributed sensing. It determines correlation between aerodynamic observables (aero forces) and structural dynamics, and allows control authority increase through aeroelastic shaping and active flow control. It offers improvements in flutter suppression and, in particular, body freedom flutter suppression, as well as aerodynamic performance of wings for increased range/endurance of manned/ unmanned flight vehicles. Other improvements include inlet performance with closed-loop active flow control, and development and validation of advanced analytical and computational tools for unsteady aerodynamics.
Evaluation of drag forcing models for vertical axis wind turbine farms
NASA Astrophysics Data System (ADS)
Pierce, Brian; Moin, Parviz; Dabiri, John
2013-11-01
Vertical axis wind turbines (VAWTs) have the potential to produce more power per unit area than horizontal axis wind turbines (HAWTs) in a wind farm setting (Kinzel et al. J. Turb. [2012]), but further understanding of the flow physics is required to design such farms. In this study we will model a large wind farm of VAWTs as an array of 100 circular cylinders which will allow a comparison with a laboratory experiment (Craig et al. DFD 2013). The geometric complexity and high Reynolds numbers necessitate phenomenological modeling of the interaction of the turbine with the fluid, which is done through point drag models similar to those found in canopy flow simulations (e.g. Dupont et al. J. Fluid Mech. [2010]). We will present a detailed study of the point drag model performance for flow over one cylinder, providing an evaluation of the model's fidelity as it relates to quantities of interest for the VAWT farm. Next we will present results for flow through the cylinder array, emphasizing validation of the model and insight into VAWT wind farm dynamics. We will also discuss the effect of wall modeling on the calculations, as the Reynolds number of the problem requires the application of wall modeling of the turbulent boundary layer above the ground to keep the cost manageable. Brian Pierce acknowledges support from the Stanford Graduate Fellowship.
NASA Astrophysics Data System (ADS)
Brooker, B. Tyler
A new nose shape that was determined using the penetration mechanics to have the least penetration drag has been tested in the supersonic wind tunnel of the University of Alabama to determine the aerodynamic characteristics of this nose shape. The aerodynamic drag measured on the new nose shape and on four additional nose shapes are compared to each other. The results show that the new nose shape has the least aerodynamic drag. The measurements were made at Mach numbers ranging from 1.85 to 3.1. This study also required the maintenance of several components of the University of Alabama's 6-inch by 6-inch supersonic wind tunnel and modification of the existing data acquisition programs. These repairs and modifications included the repair and recalibration of the supersonic wind tunnel, repair of the four component force balance, and the modification of the tunnel's control program.
Balash, Cheslav; Sterling, David; Binns, Jonathan; Thomas, Giles; Bose, Neil
2015-01-01
For prawn trawling systems, drag reduction is a high priority as the trawling process is energy intensive. Large benefits have occurred through the use of multiple-net rigs and thin twine in the netting. An additional positive effect of these successful twine-area reduction strategies is the reduced amount of otter board area required to spread the trawl systems, which leads to further drag reduction. The present work investigated the potential of redirecting the drag-strain within a prawn trawl away from the wings and the otter boards to the centre line of the trawl, where top and bottom tongues have been installed, with an aim to minimise the loading/size of the otter boards required to spread the trawl. In the system containing the new ‘W’ trawl, the drag redirected to the centre-line tongues is transferred forward through a connected sled and towing wires to the trawler. To establish the extent of drag redirection to the centre-line tongues and the relative drag benefits of the new trawl system, conventional and ‘W’ trawls of 3.65 m headline length were tested firstly over a range of spread ratios in the flume tank, and subsequently at optimum spread ratio in the field. The developed ‘W’ trawl effectively directed 64% of netting-drag off the wings and onto the centre tongues, which resulted in drag savings in the field of ∼20% for the associated ‘W’ trawl/otter-board/sled system compared to the traditional trawl/otter-board arrangement in a single trawl or twin rig configuration. Furthermore, based on previously published data, the new trawl when used in a twin rig system is expected to provide approximately 12% drag reduction compared to quad rig. The twin ‘W’ trawl system also has benefits over quad rig in that a reduced number of cod-end/By-catch Reduction Device units need to be installed and attended each tow. PMID:25751251
NASA Astrophysics Data System (ADS)
Falk, Eric Andrew
Aerodynamic forcing experiments were performed within the single-stage axial compressor of an AlliedSignal F109 turbofan engine. Unsteady velocity was measured both forward and aft of the F109 fan at several locations, with unsteady surface pressure also measured along sixteen, transducer-instrumented stator vanes. Three fan RPM were considered, with time-resolution of the unsteady data obtained through a photoelectric sensor coupled to the fan rotation. The velocity data collected forward of the fan exhibited evidence of upstream-propagating disturbances in the engine inlet flow, where these disturbances were potential in nature, emanating from the fan, and traveling acoustically in a helical pattern. The disturbance peak-to-peak unsteady amplitudes, in the swirl direction, reached nearly 50% of the mean-axial velocity at the fan face, dropping to 2--5% at one blade chord upstream. Such large velocity fluctuations may be important in terms of component high-cycle-fatigue, particularly in closely spaced, axial compressor stages. Aft of the fan, the average unsteady velocity waveforms measured across five azimuthal locations demonstrated characteristics indicative of a strong vortical and potential disturbance interaction, where the interacting disturbances had the same forcing frequency, but different amplitudes and propagation speeds. Further reduction of the fan-aft velocity data also produced evidence of upstream-propagating disturbances. These disturbances were found to be potential in nature and emanating from the F109 stator vanes; thus creating a cumulative, unsteady aerodynamic field upstream of the stators comprised of multiple interacting disturbances. The amplitudes of the stator-induced disturbances were on the order of 20--40% of the measured, downstream-propagating vortical wake amplitudes. Finally, results from stator-vane surface-pressure measurements compared favorably in both magnitude and phase to similar results collected in previous cascade
Optimal propellantless rendez-vous using differential drag
NASA Astrophysics Data System (ADS)
Dell`Elce, L.; Kerschen, G.
2015-04-01
Optimization of fuel consumption is a key driver in the design of spacecraft maneuvers. For this reason, growing interest in propellant-free maneuvers is observed in the literature. Because it allows us to turn the often-undesired drag perturbation into a control force for relative motion, differential drag is among the most promising propellantless techniques for low-Earth orbiting satellites. An optimal control approach to the problem of orbital rendez-vous using differential drag is proposed in this paper. Thanks to the scheduling of a reference maneuver by means of a direct transcription, the method is flexible in terms of cost function and can easily account for constraints of various nature. Considerations on the practical realization of differential-drag-based maneuvers are also provided. The developments are illustrated by means of high-fidelity simulations including coupled 6-degree-of-freedom simulations and an advanced aerodynamic model.
Aerodynamic analysis of an isolated vehicle wheel
NASA Astrophysics Data System (ADS)
Leśniewicz, P.; Kulak, M.; Karczewski, M.
2014-08-01
Increasing fuel prices force the manufacturers to look into all aspects of car aerodynamics including wheels, tyres and rims in order to minimize their drag. By diminishing the aerodynamic drag of vehicle the fuel consumption will decrease, while driving safety and comfort will improve. In order to properly illustrate the impact of a rotating wheel aerodynamics on the car body, precise analysis of an isolated wheel should be performed beforehand. In order to represent wheel rotation in contact with the ground, presented CFD simulations included Moving Wall boundary as well as Multiple Reference Frame should be performed. Sliding mesh approach is favoured but too costly at the moment. Global and local flow quantities obtained during simulations were compared to an experiment in order to assess the validity of the numerical model. Results of investigation illustrates dependency between type of simulation and coefficients (drag and lift). MRF approach proved to be a better solution giving result closer to experiment. Investigation of the model with contact area between the wheel and the ground helps to illustrate the impact of rotating wheel aerodynamics on the car body.
Fourier functional analysis for unsteady aerodynamic modeling
NASA Technical Reports Server (NTRS)
Lan, C. Edward; Chin, Suei
1991-01-01
A method based on Fourier analysis is developed to analyze the force and moment data obtained in large amplitude forced oscillation tests at high angles of attack. The aerodynamic models for normal force, lift, drag, and pitching moment coefficients are built up from a set of aerodynamic responses to harmonic motions at different frequencies. Based on the aerodynamic models of harmonic data, the indicial responses are formed. The final expressions for the models involve time integrals of the indicial type advocated by Tobak and Schiff. Results from linear two- and three-dimensional unsteady aerodynamic theories as well as test data for a 70-degree delta wing are used to verify the models. It is shown that the present modeling method is accurate in producing the aerodynamic responses to harmonic motions and the ramp type motions. The model also produces correct trend for a 70-degree delta wing in harmonic motion with different mean angles-of-attack. However, the current model cannot be used to extrapolate data to higher angles-of-attack than that of the harmonic motions which form the aerodynamic model. For linear ramp motions, a special method is used to calculate the corresponding frequency and phase angle at a given time. The calculated results from modeling show a higher lift peak for linear ramp motion than for harmonic ramp motion. The current model also shows reasonably good results for the lift responses at different angles of attack.
A radionuclide counting technique for measuring wind velocity. [drag force anemometers
NASA Technical Reports Server (NTRS)
Singh, J. J.; Khandelwal, G. S.; Mall, G. H.
1981-01-01
A technique for measuring wind velocities of meteorological interest is described. It is based on inverse-square-law variation of the counting rates as the radioactive source-to-counter distance is changed by wind drag on the source ball. Results of a feasibility study using a weak bismuth 207 radiation source and three Geiger-Muller radiation counters are reported. The use of the technique is not restricted to Martian or Mars-like environments. A description of the apparatus, typical results, and frequency response characteristics are included. A discussion of a double-pendulum arrangement is presented. Measurements reported herein indicate that the proposed technique may be suitable for measuring wind speeds up to 100 m/sec, which are either steady or whose rates of fluctuation are less than 1 kHz.
NASA Astrophysics Data System (ADS)
Nwankwo, Victor U. J.; Chakrabarti, Sandip K.; Weigel, Robert S.
2015-07-01
The upper atmosphere changes significantly in temperature, density and composition as a result of solar cycle variations, which causes severe storms and flares, and increases in the amount of absorbed solar radiation from solar energetic events. Satellite orbits are consequently affected by this process, especially those in low Earth orbit (LEO). In this paper, we present a model of atmospheric drag effects on the trajectory of two hypothetical LEO satellites of different ballistic coefficients, initially injected at h = 450 km. We investigate long-term trends of atmospheric drag on LEO satellites due to solar forcing induced atmospheric perturbations and heating at different phases of the solar cycle, and during short intervals of strong geomagnetic disturbances or magnetic storms. We show dependence of orbital decay on the severity of both solar cycle and phase and the extent of geomagnetic perturbations. The result of the model compares well with observed decay profile of some existing LEO satellites and provide a justification of the theoretical considerations used here.
NASA Astrophysics Data System (ADS)
Tarantini, Vincent Claudio Franco
Contributions to two missions are presented. The first is a demonstration mission called CanX-7 that uses a 4 square metre drag sail to de-orbit a 3.5 kg satellite. In order to estimate the effectiveness of the drag sail, a novel method is developed that takes into account the time-varying nature of the projected drag area. The Space Flight Laboratory designed drag sail is shown lo be sufficient to de-orbit the CanX-7 spacecraft within the 25 year requirement. The Antarctic Broadband demonstrator spacecraft is a 20 cm cubical nanosatellite that will demonstrate the feasibility of a Ka-band link between the research community in Antarctica and stakeholders in Australia. In support of this mission, a passive thermal control subsystem is designed that will keep all the components within their operational temperature limits at all times throughout the mission.
NASA Astrophysics Data System (ADS)
Lambrechts, M.; Johansen, A.; Capelo, H. L.; Blum, J.; Bodenschatz, E.
2016-06-01
The behaviour of sedimenting particles depends on the dust-to-gas ratio of the fluid. Linear stability analysis shows that solids settling in the Epstein drag regime would remain homogeneously distributed in non-rotating incompressible fluids, even when dust-to-gas ratios reach unity. However, the nonlinear evolution has not been probed before. Here, we present numerical calculations indicating that, in a particle-dense mixture, solids spontaneously mix out of the fluid and form swarms that are overdense in particles by at least a factor 10. The instability is caused by mass-loaded regions locally breaking the equilibrium background stratification. The driving mechanism depends on nonlinear perturbations of the background flow and shares some similarity to the streaming instability in accretion discs. The resulting particle-rich swarms may stimulate particle growth by coagulation. In the context of protoplanetary discs, the instability could be relevant for aiding small particles to settle to the midplane in the outer disc. Inside the gas envelopes of protoplanets, enhanced settling may lead to a reduced dust opacity, which facilitates the contraction of the envelope. We show that the relevant physical set up can be recreated in a laboratory setting. This will allow our numerical calculations to be investigated experimentally in the future.
NASA Technical Reports Server (NTRS)
Mennell, R. C.
1974-01-01
Tests were conducted to investigate various base drag reduction techniques in an attempt to improve Orbiter lift-to-drag ratios and to calculate sting interference effects on the Orbiter aerodynamic characteristics. Test conditions and facilites, and model dimensional data are presented along with the data reduction guidelines and data set/run number collation used for the studies. Aerodynamic force and moment data and the results of stability and control tests are also given.
NASA Astrophysics Data System (ADS)
Colpi, Monica; Pallavicini, Andrea
1998-07-01
The drag force on a satellite of mass M moving with speed V in the gravitational field of a spherically symmetric background of stars is computed. During the encounter, the stars are subject to a time-dependent force that alters their equilibrium. The resulting distortion in the stellar density field acts back to produce a force FΔ that decelerates the satellite. This force is computed using a perturbative technique known as linear response theory. In this paper, we extend the formalism of linear response to derive the correct expression for the back-reaction force FΔ that applies when the stellar system is described by an equilibrium one-particle distribution function. FΔ is expressed in terms of a suitable correlation function that couples the satellite dynamics to the unperturbed dynamics of the stars. At time t, the force depends upon the whole history of the composite system. In the formalism, we account for the shift of the stellar center of mass resulting from linear momentum conservation. The self-gravity of the response is neglected since it contributes to a higher order in the perturbation. Linear response theory applies also to the case of a satellite orbiting outside the spherical galaxy. The case of a satellite moving on a straight line, at high speed relative to the stellar dispersion velocity, is explored. We find that the satellite during its passage raises (1) global tides in the stellar distribution and (2) a wake, i.e., an overdense region behind its trail. If the satellite motion is external to the galaxy, it suffers a dissipative force that is not exclusively acting along V but acquires a component along R, the position vector relative to the center of the spherical galaxy. We derive the analytical expression of the force in the impulse approximation. In penetrating short-lived encounters, the satellite moves across the stellar distribution and the transient wake excited in the density field is responsible for most of the deceleration. We
The aerodynamic cost of head morphology in bats: maybe not as bad as it seems.
Vanderelst, Dieter; Peremans, Herbert; Razak, Norizham Abdul; Verstraelen, Edouard; Dimitriadis, Grigorios; Dimitriadis, Greg
2015-01-01
At first sight, echolocating bats face a difficult trade-off. As flying animals, they would benefit from a streamlined geometric shape to reduce aerodynamic drag and increase flight efficiency. However, as echolocating animals, their pinnae generate the acoustic cues necessary for navigation and foraging. Moreover, species emitting sound through their nostrils often feature elaborate noseleaves that help in focussing the emitted echolocation pulses. Both pinnae and noseleaves reduce the streamlined character of a bat's morphology. It is generally assumed that by compromising the streamlined charactered of the geometry, the head morphology generates substantial drag, thereby reducing flight efficiency. In contrast, it has also been suggested that the pinnae of bats generate lift forces counteracting the detrimental effect of the increased drag. However, very little data exist on the aerodynamic properties of bat pinnae and noseleaves. In this work, the aerodynamic forces generated by the heads of seven species of bats, including noseleaved bats, are measured by testing detailed 3D models in a wind tunnel. Models of Myotis daubentonii, Macrophyllum macrophyllum, Micronycteris microtis, Eptesicus fuscus, Rhinolophus formosae, Rhinolophus rouxi and Phyllostomus discolor are tested. The results confirm that non-streamlined facial morphologies yield considerable drag forces but also generate substantial lift. The net effect is a slight increase in the lift-to-drag ratio. Therefore, there is no evidence of high aerodynamic costs associated with the morphology of bat heads. PMID:25739038
The Aerodynamic Cost of Head Morphology in Bats: Maybe Not as Bad as It Seems
Vanderelst, Dieter; Peremans, Herbert; Razak, Norizham Abdul; Verstraelen, Edouard; Dimitriadis, Greg
2015-01-01
At first sight, echolocating bats face a difficult trade-off. As flying animals, they would benefit from a streamlined geometric shape to reduce aerodynamic drag and increase flight efficiency. However, as echolocating animals, their pinnae generate the acoustic cues necessary for navigation and foraging. Moreover, species emitting sound through their nostrils often feature elaborate noseleaves that help in focussing the emitted echolocation pulses. Both pinnae and noseleaves reduce the streamlined character of a bat’s morphology. It is generally assumed that by compromising the streamlined charactered of the geometry, the head morphology generates substantial drag, thereby reducing flight efficiency. In contrast, it has also been suggested that the pinnae of bats generate lift forces counteracting the detrimental effect of the increased drag. However, very little data exist on the aerodynamic properties of bat pinnae and noseleaves. In this work, the aerodynamic forces generated by the heads of seven species of bats, including noseleaved bats, are measured by testing detailed 3D models in a wind tunnel. Models of Myotis daubentonii, Macrophyllum macrophyllum, Micronycteris microtis, Eptesicus fuscus, Rhinolophus formosae, Rhinolophus rouxi and Phyllostomus discolor are tested. The results confirm that non-streamlined facial morphologies yield considerable drag forces but also generate substantial lift. The net effect is a slight increase in the lift-to-drag ratio. Therefore, there is no evidence of high aerodynamic costs associated with the morphology of bat heads. PMID:25739038
Rarefaction Effects in Hypersonic Aerodynamics
NASA Astrophysics Data System (ADS)
Riabov, Vladimir V.
2011-05-01
The Direct Simulation Monte-Carlo (DSMC) technique is used for numerical analysis of rarefied-gas hypersonic flows near a blunt plate, wedge, two side-by-side plates, disk, torus, and rotating cylinder. The role of various similarity parameters (Knudsen and Mach numbers, geometrical and temperature factors, specific heat ratios, and others) in aerodynamics of the probes is studied. Important kinetic effects that are specific for the transition flow regime have been found: non-monotonic lift and drag of plates, strong repulsive force between side-by-side plates and cylinders, dependence of drag on torus radii ratio, and the reverse Magnus effect on the lift of a rotating cylinder. The numerical results are in a good agreement with experimental data, which were obtained in a vacuum chamber at low and moderate Knudsen numbers from 0.01 to 10.
NASA Astrophysics Data System (ADS)
Suzuki, Masahiro; Nakade, Koji; Ido, Atsushi
As the maximum speed of high-speed trains increases, flow-induced vibration of trains in tunnels has become a subject of discussion in Japan. In this paper, we report the result of a study on use of modifications of train shapes as a countermeasure for reducing an unsteady aerodynamic force by on-track tests and a wind tunnel test. First, we conduct a statistical analysis of on-track test data to identify exterior parts of a train which cause the unsteady aerodynamic force. Next, we carry out a wind tunnel test to measure the unsteady aerodynamic force acting on a train in a tunnel and examined train shapes with a particular emphasis on the exterior parts identified by the statistical analysis. The wind tunnel test shows that fins under the car body are effective in reducing the unsteady aerodynamic force. Finally, we test the fins by an on-track test and confirmed its effectiveness.
Aerodynamic characteristics of NACA 4412 airfoil sction with flap
NASA Astrophysics Data System (ADS)
Ockfen, Alex E.; Matveev, Konstantin I.
2009-09-01
Wing-in-Ground vehicles and aerodynamically assisted boats take advantage of increased lift and reduced drag of wing sections in the ground proximity. At relatively low speeds or heavy payloads of these craft, a flap at the wing trailing-ground-effect flow id numerically investigated in this study. The computational method consists of a steady-state, incompressible, finite volume method utilizing the Spalart-Allmaras turbulence model. Grid generation and solution of the Navier-Stokes equations are completed flow with a flap, as well as ground-effect motion without a flap. Aerodynamic forces are plain flap. Changes in the flow introduced with the flap addition are also discussed. Overall, the use of a flap on wings with small attack angles is found to be beneficial for small flap deflections up to 5% of the chord, where the contribution of lift augmentation exceeds the drag increase, yielding an augmented lift-to-drag ratio
Sullivan, W. N.; Leonard, T. M.
1980-11-01
An important aspect of structural design of the Darrieus rotor is the determination of aerodynamic blade loads. This report describes a load generator which has been used at Sandia for quasi-static and dynamic rotor analyses. The generator is based on the single streamtube aerodynamic flow model and is constructed as a FORTRAN IV subroutine to facilitate its use in finite element structural models. Input and output characteristics of the subroutine are described and a complete listing is attached as an appendix.
Uncovering changes in spider orb-web topology owing to aerodynamic effects
Zaera, Ramón; Soler, Alejandro; Teus, Jaime
2014-01-01
An orb-weaving spider's likelihood of survival is influenced by its ability to retain prey with minimum damage to its web and at the lowest manufacturing cost. This set of requirements has forced the spider silk to evolve towards extreme strength and ductility to a degree that is rare among materials. Previous studies reveal that the performance of the web upon impact may not be based on the mechanical properties of silk alone, aerodynamic drag could play a role in the dissipation of the prey's energy. Here, we present a thorough analysis of the effect of the aerodynamic drag on wind load and prey impact. The hypothesis considered by previous authors for the evaluation of the drag force per unit length of thread has been revisited according to well-established principles of fluid mechanics, highlighting the functional dependence on thread diameter that was formerly ignored. Theoretical analysis and finite-element simulations permitted us to identify air drag as a relevant factor in reducing deterioration of the orb web, and to reveal how the spider can take greater—and not negligible—advantage of drag dissipation. The study shows the beneficial air drag effects of building smaller and less dense webs under wind load, and larger and denser webs under prey impact loads. In essence, it points out why the aerodynamics need to be considered as an additional driving force in the evolution of silk threads and orb webs. PMID:24966235
ERIC Educational Resources Information Center
Pestka, Kenneth A., II; Heindel, Jennifer
2015-01-01
This activity is designed to illustrate an application of resistive forces in the introductory physics curriculum with an interdisciplinary twist. Students are asked to examine images of riverbed boulders after a flood and estimate the water flow that was needed to push the boulders downstream. The activity provides an opportunity for students to…
Performance Level Differences in Swimming: A Meta-Analysis of Passive Drag Force
ERIC Educational Resources Information Center
Havriluk, Rod
2005-01-01
The streamline is a basic position for competitive swimming starts mid turns and has been used in many studies on resistive forces. However, there is a wide yahweh, of theoretical interpretations in these studies, leading to diverse and questionable conclusions. The purpose of this study was to determine performance level differences in the…
Drag force on a sphere moving toward an anisotropic superhydrophobic plane.
Asmolov, Evgeny S; Belyaev, Aleksey V; Vinogradova, Olga I
2011-08-01
We analyze theoretically a high-speed drainage of liquid films squeezed between a hydrophilic sphere and a textured superhydrophobic plane that contains trapped gas bubbles. A superhydrophobic wall is characterized by parameters L (texture characteristic length), b1 and b2 (local slip lengths at solid and gas areas), and φ1 and φ2 (fractions of solid and gas areas). Hydrodynamic properties of the plane are fully expressed in terms of the effective slip-length tensor with eigenvalues that depend on texture parameters and H (local separation). The effect of effective slip is predicted to decrease the force as compared with what is expected for two hydrophilic surfaces and described by the Taylor equation. The presence of additional length scales, L, b1, and b2, implies that a film drainage can be much richer than in the case of a sphere moving toward a hydrophilic plane. For a large (compared to L) gap the reduction of the force is small, and for all textures the force is similar to expected when a sphere is moving toward a smooth hydrophilic plane that is shifted down from the superhydrophobic wall. The value of this shift is equal to the average of the eigenvalues of the slip-length tensor. By analyzing striped superhydrophobic surfaces, we then compute the correction to the Taylor equation for an arbitrary gap. We show that at a thinner gap the force reduction becomes more pronounced, and that it depends strongly on the fraction of the gas area and local slip lengths. For small separations we derive an exact equation, which relates a correction for effective slip to texture parameters. Our analysis provides a framework for interpreting recent force measurements in the presence of a superhydrophobic surface. PMID:21929113
NASA Astrophysics Data System (ADS)
Chu, Chin-Chou; Chang, Chien C.; Hsieh, Chen-Ta
2009-11-01
The lift and thrust associated with insect flight strongly depend on the complex wake patterns produced by wing-wing and wing-wake interactions. We propose to investigate the aerodynamics of dragonfly using a simplified wing-wing model from the perspective of many-body force decomposition (JFM 600, p95) and the associated force elements. The aerodynamic force, lift or thrust, of the wing-wing system is analyzed in terms of its four constituent components, each of which is directly related to a physical effect. These force components for each individual wing include two potential contributions credited to the wing motion itself, contribution from the vorticity within the flow, and contributions from the surface vorticity on its and other wing's surfaces. The potential contribution due to added-mass effect is often non-negligible. Nevertheless, the major contribution to the forces comes from the vorticity within the flow. The relative importance of these components relies heavily on the motions of the two wings such as the respective angles of attack, the amplitude and speed of translational motions, and the amplitude and speed of wing rotations. In addition to the dynamic stall vortex, several important mechanisms of high lift or thrust are also identified.
Pande, Jayant; Smith, Ana-Sunčana
2015-03-28
In this analytical study we demonstrate the richness of behaviour exhibited by bead-spring micro-swimmers, both in terms of known yet not fully explained effects such as synchronisation, and hitherto undiscovered phenomena such as the existence of two transport regimes where the swimmer shape has fundamentally different effects on the velocity. For this purpose we employ a micro-swimmer model composed of three arbitrarily-shaped rigid beads connected linearly by two springs. By analysing this swimmer in terms of the forces on the different beads, we determine the optimal kinematic parameters for sinusoidal driving, and also explain the pusher/puller nature of the swimmer. Moreover, we show that the phase difference between the swimmer's arms automatically attains values which maximise the swimming speed for a large region of the parameter space. Apart from this, we determine precisely the optimal bead shapes that maximise the velocity when the beads are constrained to be ellipsoids of a constant volume or surface area. On doing so, we discover the surprising existence of the aforementioned transport regimes in micro-swimming, where the motion is dominated by either a reduction of the drag force opposing the beads, or by the hydrodynamic interaction amongst them. Under some conditions, these regimes lead to counter-intuitive effects such as the most streamlined shapes forming locally the slowest swimmers. PMID:25675985
Hub and pylon fairing integration for helicopter drag reduction
NASA Technical Reports Server (NTRS)
Martin, D. M.; Mort, R. W.; Squires, P. K.; Young, L. A.
1991-01-01
The results of testing hub and pylon fairings mounted on a one-fifth scale helicopter with the goal of reducing parasite drag are presented. Lift, drag, and pitching moment, as well as side force and yawing moment, were measured. The primary objective of the test was to validate the drag reduction capability of integrated hub and pylon configurations in the aerodynamic environment produced by a rotating hub in forward flight. In addition to the baseline helicopter without fairings, three hub fairings and three pylon fairings were tested in various combinations. The three hub fairings tested reflect two different conceptual design approaches to implementing an integrated fairing configuration on an actual aircraft. The design philosophy is discussed in detail and comparisons are made between the wind tunnel models and potential full-scale prototypes. The data show that model drag can be reduced by as much as 20.8 percent by combining a small hub fairing with circular arc upper and flat lower surfaces and a nontapered 34-percent thick pylon fairing. Aerodynamic effects caused by the fairings, which may have a significant impact on static longitudinal and directional stability, were observed. The results support previous research which showed that the greatest reduction in model drag is achieved if the hub and pylon fairings are integrated with minimum gap between the two.
NASA Astrophysics Data System (ADS)
Utvich, Alexis; Jemmott, Colin; Logan, Sheldon; Rossmann, Jenn
2003-11-01
A team of undergraduate students has performed experiments on Wiffle balls in the Harvey Mudd College wind tunnel facility. Wiffle balls are of particular interest because they can attain a curved trajectory with little or no pitcher-imparted spin. The reasons behind this have not previously been quantified formally. A strain gauge device was designed and constructed to measure the lift and drag forces on the Wiffle ball; a second device to measure lift and drag on a spinning ball was also developed. Experiments were conducted over a range of Reynolds numbers corresponding to speeds of roughly 0-40 mph. Lift forces of up to 0.2 N were measured for a Wiffle ball at 40 mph. This is believed to be due to air flowing into the holes on the Wiffle ball in addition to the effect of the holes on external boundary layer separation. A fog-based flow visualization system was developed in order to provide a deeper qualitative understanding of what occurred in the flowfield surrounding the ball. The data and observations obtained in this study support existing assumptions about Wiffle ball aerodynamics and begin to elucidate the mechanisms involved in Wiffle ball flight.
NASA Technical Reports Server (NTRS)
Jones, R. T. (Compiler)
1979-01-01
A collection of papers on modern theoretical aerodynamics is presented. Included are theories of incompressible potential flow and research on the aerodynamic forces on wing and wing sections of aircraft and on airship hulls.
NASA Technical Reports Server (NTRS)
Ostowari, C.; Naik, D.
1986-01-01
The experimental procedure and aerodynamic force and moment measurements for wind tunnel testing of the three lifting surface configuration (TLC) are described. The influence of nonelliptical lift distributions on lift, drag, and static longitudinal stability are examined; graphs of the lift coefficient versus angle of attack, the pitching moment coefficient, drag coefficient, and lift to drag ratio versus lift coefficient are provided. The TLC data are compared with the conventional tail-aft configuration and the canard-wing configuration; it is concluded that the TLC has better lift and high-lift drag characteristics, lift to drag ratio, and zero-lift moments than the other two configurations. The effects of variations in forward and tail wind incidence angles, gap, stagger, and forward wind span on the drag, lift, longitudinal stability, and zero-lift moments of the configuration are studied.
Drag-shield drop tower residual acceleration optimisation
NASA Astrophysics Data System (ADS)
Figueroa, A.; Sorribes-Palmer, F.; Fernandez De Pierola, M.; Duran, J.
2016-07-01
Among the forces that appear in drop towers for microgravity experiments, aerodynamic drag plays a crucial role in the residual acceleration. Buoyancy can also be critical, especially at the first instances of the drop when the low speed of the experimental platform makes the aerodynamic drag small compared with buoyancy. In this paper the perturbation method is used to formulate an analytical model which has been validated experimentally. The experimental test was conduced by undergraduate students of aerospace engineering at the Institute of Microgravity ‘Ignacio Da Riva’ of the Technical University of Madrid (IDR/UPM) microgravity tower. The test helped students to understand the influence of the buoyancy on the residual acceleration of the experiment platform. The objective of the students was to understand the physical process during the drop, identify the main parameters involved in the residual acceleration and determine the most suitable configuration for the next drop tower proposed to be built at UPM.
Aerodynamics of a Cycling Team in a Time Trial: Does the Cyclist at the Front Benefit?
ERIC Educational Resources Information Center
Iniguez-de-la Torre, A.; Iniguez, J.
2009-01-01
When seasonal journeys take place in nature, birds and fishes migrate in groups. This provides them not only with security but also a considerable saving of energy. The power they need to travel requires overcoming aerodynamic or hydrodynamic drag forces, which can be substantially reduced when the group travels in an optimal arrangement. Also in…
NASA Technical Reports Server (NTRS)
Folta, David C.; Baker, David F.
1991-01-01
The FREEMAC program used to generate the aerodynamic coefficients, as well as associated routines that allow the results to be used in other software is described. These capabilities are applied in two numerical examples to the short-term orbit prediction of the Gamma Ray Observatory (GRO) and Hubble Space Telescope (HST) spacecraft. Predictions using attitude-dependent aerodynamic coefficients were made on a modified version of the PC-based Ephemeris Generation Program (EPHGEN) and were compared to definitive orbit solutions obtained from actual tracking data. The numerical results show improvement in the predicted semi-major axis and along-track positions that would seem to be worth the added computational effort. Finally, other orbit and attitude analysis applications are noted that could profit from using FREEMAC-calculated aerodynamic coefficients, including orbital lifetime studies, orbit determination methods, attitude dynamics simulators, and spacecraft control system component sizing.
NASA Technical Reports Server (NTRS)
Schiff, L. B.
1974-01-01
Concepts from the theory of functionals are used to develop nonlinear formulations of the aerodynamic force and moment systems acting on bodies in large-amplitude, arbitrary motions. The analysis, which proceeds formally once the functional dependence of the aerodynamic reactions upon the motion variables is established, ensures the inclusion, within the resulting formulation, of pertinent aerodynamic terms that normally are excluded in the classical treatment. Applied to the large-amplitude, slowly varying, nonplanar motion of a body, the formulation suggests that the aerodynamic moment can be compounded of the moments acting on the body in four basic motions: steady angle of attack, pitch oscillations, either roll or yaw oscillations, and coning motion. Coning, where the nose of the body describes a circle around the velocity vector, characterizes the nonplanar nature of the general motion.
STS-76 Landing - Space Shuttle Atlantis Lands at Edwards Air Force Base, Drag Chute Deploy
NASA Technical Reports Server (NTRS)
1996-01-01
The space shuttle Atlantis touches down on the runway at Edwards, California, at approximately 5:29 a.m. Pacific Standard Time after completing the highly successful STS-76 mission to deliver Astronaut Shannon Lucid to the Russian Space Station Mir. She was the first American woman to serve as a Mir station researcher. Atlantis was originally scheduled to land at Kennedy Space Center, Florida, but bad weather there both 30 and 31 March necessitated a landing at the backup site at Edwards. This photo shows the drag chute deployed to help the shuttle roll to a stop. Mission commander for STS-76 was Kevin P. Chilton, and Richard A. Searfoss was the pilot. Ronald M. Sega was payload commander and mission specialist-1. Mission specialists were Richard Clifford, Linda Godwin and Shannon Lucid. The mission also featured a spacewalk while Atlantis was docked to Mir and experiments aboard the SPACEHAB module. Space Shuttles are the main element of America's Space Transportation System and are used for space research and other space applications. The shuttles are the first vehicles capable of being launched into space and returning to Earth on a routine basis. Space Shuttles are used as orbiting laboratories in which scientists and mission specialists conduct a wide variety of scientific experiments. Crews aboard shuttles place satellites in orbit, rendezvous with satellites to carry out repair missions and return them to space, and retrieve satellites and return them to Earth for refurbishment and reuse. Space Shuttles are true aerospace vehicles. They leave Earth and its atmosphere under rocket power provided by three liquid-propellant main engines with two solid-propellant boosters attached plus an external liquid-fuel tank. After their orbital missions, they streak back through the atmosphere and land like airplanes. The returning shuttles, however, land like gliders, without power and on runways. Other rockets can place heavy payloads into orbit, but, they can only be
STS-76 Landing - Space Shuttle Atlantis Lands at Edwards Air Force Base, Drag Chute Deploy
NASA Technical Reports Server (NTRS)
1996-01-01
The space shuttle Atlantis touches down on the runway at Edwards, California, at approximately 5:29 a.m. Pacific Standard Time after completing the highly successful STS-76 mission to deliver Astronaut Shannon Lucid to the Russian Space Station Mir. She was the first American woman to serve as a Mir station researcher. Atlantis was originally scheduled to land at Kennedy Space Center, Florida, but bad weather there both 30 and 31 March necessitated a landing at the backup site at Edwards. This photo shows the drag chute deployed to help the shuttle roll to a stop. Mission commander for STS-76 was Kevin P. Chilton, and Richard A. Searfoss was the pilot. Ronald M. Sega was payload commander and mission specialist-1. Mission specialists were Richard Clifford, Linda Godwin and Shannon Lucid. The mission also featured a spacewalk while Atlantis was docked to Mir and experiments aboard the SPACEHAB module. Space Shuttles are the main element of America's Space Transportation System and are used for space research and other space applications. The shuttles are the first vehicles capable of being launched into space and returning to Earth on a routine basis. Space Shuttles are used as orbiting laboratories in which scientists and mission specialists conduct a wide variety of scientific experiments. Crews aboard shuttles place satellites in orbit, rendezvous with satellites to carry out repair missions and return them to space, and retrieve satellites and return them to Earth for refurbishment and reuse. Space Shuttles are true aerospace vehicles. They leave Earth and its atmosphere under rocket power provided by three liquid-propellant main engines with two solid-propellant boosters attached plus an external liquid-fuel tank. After their orbital missions, they streak back through the atmosphere and land like airplanes. The returning shuttles, however, land like gliders, without power and on runways. Other rockets can place heavy payloads into orbit, but, they can only be
Schwarzschild black hole embedded in a dust field: scattering of particles and drag force effects
NASA Astrophysics Data System (ADS)
Bini, Donato; Geralico, Andrea
2016-06-01
A ‘temporal analogue’ of the standard Poynting–Robertson effect is analyzed as induced by a dust of particles (instead of a gas of photons) surrounding a Schwarzschild black hole. Test particles inside this cloud undergo acceleration effects due to the presence of a friction force, so that the fate of their evolution can be completely different from the corresponding geodesic motion. Typical situations are discussed of hyperbolic motion of particles scattered by the black hole in the presence of a dust filling the whole spacetime region outside the horizon as well as particles which free fall radially crossing a corona located at a certain distance from the horizon. The existence of equilibrium orbits may prevent particles from either falling into the hole or escaping to infinity.
NASA Technical Reports Server (NTRS)
Mennell, R. C.
1973-01-01
Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the Rockwell -89A Light Weight Space Shuttle Orbiter. The test purpose was to obtain pressure loads data in the presence of the ground for orbiter structural strength analysis. Aerodynamic force data was also recorded to allow correlation with all pressure loads information. Angles of attack from minus 3 deg to 18 deg and angles of sideslip of 0 deg, plus or minus 50 deg, and plus or minus 10 deg were tested in the presence of the NAAL ground plane. Static pressure bugs were used to obtain a pressure loads survey of the basic configuration, elevon deflections of 5 deg, 10 deg, 15 deg, and minus 20 deg and a rudder deflection of minus 15 deg, at a tunnel dynamic pressure of 40 psi. The test procedure was to locate a maximum of 30 static pressure bugs on the model surface at various locations calculated to prevent aerodynamic and physical interference. Then by various combinations of location the pressure bugs output was to define a complete pressure survey for the fuselages, wing, vertical tail, and main landing gear door.
NASA Astrophysics Data System (ADS)
Menezes, V.; Sun, M.; Jagadeesh, G.; Reddy, K. P. J.; Takayama, K.
The problem of wake flow at high speeds and the drag associated with it are a significant source of observation in the design of missiles, projectiles and other typical high speed vehicles. A large separated wake at the base of the body in flight would cause an increase in the overall drag due to reduced base pressure force, which otherwise would oppose the axial force on the body. The wake studies of high speed bodies also gain importance due to the severe aerodynamic heating problem and a high rise in the temperature of the base flow.
X-43A Flight-Test-Determined Aerodynamic Force and Moment Characteristics at Mach 7.0
NASA Technical Reports Server (NTRS)
Davis, Mark C.; White, J. Terry
2008-01-01
The second flight of the Hyper-X program afforded a unique opportunity to determine the aerodynamic force and moment characteristics of an airframe-integrated scramjet-powered aircraft in hypersonic flight. These data were gathered via a repeated series of pitch, yaw, and roll doublets, frequency sweeps, and pushover-pullup maneuvers performed throughout the X-43A cowl-closed descent. Maneuvers were conducted at Mach numbers of 6.80-0.95 and at altitudes from 92,000 ft mean sea level to sea level. The dynamic pressure varied from 1300 to 400 psf with the angle of attack ranging from 0 to 14 deg. The flight-extracted aerodynamics were compared with preflight predictions based on wind-tunnel test data. The X-43A flight-derived axial force was found to be 10-15%higher than prediction. Underpredictions of similar magnitude were observed for the normal force. For Mach numbers above 4.0, the flight-derived stability and control characteristics resulted in larger-than-predicted static margins, with the largest discrepancy approximately 5 in. forward along the x-axis center of gravity at Mach 6.0. This condition would result in less static margin in pitch. The predicted lateral-directional stability and control characteristics matched well with flight data when allowance was made for the high uncertainty in angle of sideslip.
NASA Technical Reports Server (NTRS)
Davis, Mark C.; White, J. Terry
2006-01-01
The second flight of the HYPER-X Program afforded a unique opportunity to determine the aerodynamic force and moment characteristics of an airframe integrated scramjet powered aircraft in hypersonic flight. These data were gathered via a repeated series of pitch, yaw, and roll doublets, frequency sweeps, and pull-up/push-over maneuvers performed throughout the X-43A cowl-closed descent phase. The subject flight research maneuvers were conducted in a Mach number range of 6.8 to 0.95 at altitudes from 92,000 ft to sea level. In this flight regime, the dynamic pressure varied from 1300 psf to 400 psf with angle-of-attack ranging from 0 deg to 14 deg. The flight-extracted aerodynamics were compared with pre-flight predictions based on wind tunnel test data. The X-43A flight-derived axial force was found to be 10 to 15 percent higher than prediction. Under-predictions of similar magnitude were observed for the normal force. For Mach numbers greater than 4, the X-43A flight-derived stability and control characteristics resulted in larger than predicted static margins, with the largest discrepancy approximately 5-inches forward along the X(CG) at Mach 6. This would result in less static margin in pitch. The X-43A predicted lateral-directional stability and control characteristics matched well with flight data when allowance was made for the high uncertainty in angle-of-sideslip.
Flight-Test-Determined Aerodynamic Force and Moment Characteristics of the X-43A at Mach 7.0
NASA Technical Reports Server (NTRS)
Davis. Marl C.; White, J. Terry
2006-01-01
The second flight of the Hyper-X program afforded a unique opportunity to determine the aerodynamic force and moment characteristics of an airframe-integrated scramjet-powered aircraft in hypersonic flight. These data were gathered via a repeated series of pitch, yaw, and roll doublets; frequency sweeps; and pushover-pullup maneuvers performed throughout the X-43A cowl-closed descent. Maneuvers were conducted at Mach numbers of 6.80 to 0.95 and altitudes from 92,000 ft msl to sea level. The dynamic pressure varied from 1300 psf to 400 psf with the angle of attack ranging from 0 deg to 14 deg. The flight-extracted aerodynamics were compared with preflight predictions based on wind-tunnel-test data. The X-43A flight-derived axial force was found to be 10 percent to 15 percent higher than prediction. Under-predictions of similar magnitude were observed for the normal force. For Mach numbers above 4.0, the flight-derived stability and control characteristics resulted in larger-than-predicted static margins, with the largest discrepancy approximately 5 in. forward along the x-axis center of gravity at Mach 6.0. This condition would result in less static margin in pitch. The predicted lateral-directional stability and control characteristics matched well with flight data when allowance was made for the high uncertainty in angle of sideslip.
An investigation of drag reduction for tractor trailer vehicles
NASA Technical Reports Server (NTRS)
Muirhead, V. U.
1978-01-01
Force and moment data were obtained from a one-twenty-fifth scale wind tunnel model of a cab-over-engine tractor trailer combination. The tests define the aerodynamic characteristics of the baseline (unmodified) vehicle and several modified configurations. The primary modifications consist of: (1) greatly increased forebody corner radii, (2) a smooth fairing over the cab-to-trailer gap, (3) a smoothed underbody, and (4) rear streamlining (boattailing)of the trailer. Tests were conducted for yaw angles from 0 deg to 30 deg. The reduction in drag, relative to the baseline, obtained by combining the modifications are compared for the zero yaw condition with full scale coast down drag results for similar configurations. The drag reductions obtained from the model and full scale tests are in good agreement.
NASA Technical Reports Server (NTRS)
Srivastava, R.; Reddy, T. S. R.
1996-01-01
This guide describes the input data required, for steady or unsteady aerodynamic and aeroelastic analysis of propellers and the output files generated, in using PROP3D. The aerodynamic forces are obtained by solving three dimensional unsteady, compressible Euler equations. A normal mode structural analysis is used to obtain the aeroelastic equations, which are solved using either time domain or frequency domain solution method. Sample input and output files are included in this guide for steady aerodynamic analysis of single and counter-rotation propellers, and aeroelastic analysis of single-rotation propeller.
Aerodynamics of Satellites on a Super Low Earth Orbit
NASA Astrophysics Data System (ADS)
Fujita, Kazuhisa; Noda, Atsushi
2008-12-01
The Super Low Altitude Test Satellite is an engineering test satellite currently under development in Japan Aerospace Exploration Agency in an attempt to open a new frontier of space utilization on extremely low earth orbits. In the presence of aerodynamic forces acting on the satellite, the altitude and attitude of the satellite are maintained by ion engines so that the aerodynamic drag can be canceled. Thus, it is of primary importance to accurately assess the aerodynamics characteristics of the satellite prior to flight. In this article, the aerodynamic coefficients of the satellite are calculated for orbital altitudes from 160 to 300 km, taking into account the Maxwell accommodation of particles on the satellite surface and the free stream chemical composition. The activated atomic oxygen fluence rate on the surface, which is expected to cause considerable damages on the surface material, is estimated as well.
NASA Technical Reports Server (NTRS)
Horstman, Raymond H.
1992-01-01
Aerodynamic flow achieved by adding fixed fairings to butterfly valve. When valve fully open, fairings align with butterfly and reduce wake. Butterfly free to turn, so valve can be closed, while fairings remain fixed. Design reduces turbulence in flow of air in internal suction system. Valve aids in development of improved porous-surface boundary-layer control system to reduce aerodynamic drag. Applications primarily aerospace. System adapted to boundary-layer control on high-speed land vehicles.
Aerodynamics of Heavy Vehicles
NASA Astrophysics Data System (ADS)
Choi, Haecheon; Lee, Jungil; Park, Hyungmin
2014-01-01
We present an overview of the aerodynamics of heavy vehicles, such as tractor-trailers, high-speed trains, and buses. We introduce three-dimensional flow structures around simplified model vehicles and heavy vehicles and discuss the flow-control devices used for drag reduction. Finally, we suggest important unsteady flow structures to investigate for the enhancement of aerodynamic performance and future directions for experimental and numerical approaches.
Norberg, U M
1976-08-01
The kinematics, aerodynamics, and energetics of Plecotus auritus in slow horizontal flight, 2-35 m s-1, are analysed. At this speed the inclination of the stroke path is ca. 58 degrees to the horizontal, the stroke angle ca. 91 degrees, and the stroke frequency ca. 11-9 Hz. A method, based on steady-state aerodynamic and momenthum theories, is derived to calculate the lift and drag coefficients as averaged over the whole wing the whole wing-stroke for horizontal flapping flight. This is a further development of Pennycuick's (1968) and Weis-Fogh's (1972) expressions for calculating the lift coefficient. The lift coefficient obtained varies between 1-4 and 1-6, the drag coefficient between 0-4 and 1-2, and the lift:drag ratio between 1-2 and 4-0. The corresponding, calculated, total specific mechanical power output of the wing muscles varies between 27-0 and 40-4 W kg-1 body mass. A maximum estimate of mechanical efficiency is 0-26. The aerodynamic efficiency varies between 0-07 and 0-10. The force coefficient, total mechanical power output, and mechanical and aerodynamic efficiencies are all plausible, demonstrating that the slow flapping flight of Plecotus is thus explicable by steady-state aerodynamics. The downstroke is the power stroke for the vertical upward forces and the upstroke for the horizontal forward forces. PMID:993701
Knoerzer, Markus; Szydzik, Crispin; Tovar-Lopez, Francisco Javier; Tang, Xinke; Mitchell, Arnan; Khoshmanesh, Khashayar
2016-02-01
Dielectrophoresis is a widely used means of manipulating suspended particles within microfluidic systems. In order to efficiently design such systems for a desired application, various numerical methods exist that enable particle trajectory plotting in two or three dimensions based on the interplay of hydrodynamic and dielectrophoretic forces. While various models are described in the literature, few are capable of modeling interactions between particles as well as their surrounding environment as these interactions are complex, multifaceted, and computationally expensive to the point of being prohibitive when considering a large number of particles. In this paper, we present a numerical model designed to enable spatial analysis of the physical effects exerted upon particles within microfluidic systems employing dielectrophoresis. The model presents a means of approximating the effects of the presence of large numbers of particles through dynamically adjusting hydrodynamic drag force based on particle density, thereby introducing a measure of emulated particle-particle and particle-liquid interactions. This model is referred to as "dynamic drag force based on iterative density mapping." The resultant numerical model is used to simulate and predict particle trajectory and velocity profiles within a microfluidic system incorporating curved dielectrophoretic microelectrodes. The simulated data are compared favorably with experimental data gathered using microparticle image velocimetry, and is contrasted against simulated data generated using traditional "effective moment Stokes-drag method," showing more accurate particle velocity profiles for areas of high particle density. PMID:26643028
Modeling flows over gravel beds by a drag force method and a modified S-A turbulence closure
NASA Astrophysics Data System (ADS)
Zeng, C.; Li, C. W.
2012-09-01
A double-averaged Navier-Stokes equations (DANS) model has been developed for depth-limited open channel flows over gravels. Three test cases are used to validate the model: an open-channel flow over a densely packed gravel bed with small-scale uniform roughness (D/d50 ˜ 13, d50 = median diameter of roughness elements, D = water depth), open-channel flows over large-scale sparsely distributed roughness elements (D/Δ ˜ 2.3-8.7, Δ = roughness height) and steep slope gravel-bed river flows with D/d50 ˜ 7-25. Various methods of treatment of the gravel-induced resistance effect have been investigated. The results show that the wall function approach (WFA) is successful in simulating flows over small gravels but is not appropriate for large gravels since the vertical profile of the longitudinal velocity does not follow the logarithmic-linear relationship. The drag force method (DFM) performs better but the non-logarithmic velocity distribution generated by sparsely distributed gravels cannot be simulated accurately. Noting that the turbulence length scale within the gravel layer is governed by the gravel size, the DANS model incorporating the DFM and a modified Spalart-Allmaras (S-A) turbulence closure is proposed. The turbulence length scale parameter in the S-A model is modified to address the change in the turbulence structure within the gravel layer. The computed velocity profiles agree well with the corresponding measured profiles in all cases. Particularly, the model reproduces the S-shape velocity profile for sparsely distributed large size roughness elements. The modeling methodology is robust and can be easily integrated into the existing numerical models.
Ben-Gida, Hadar; Kirchhefer, Adam; Taylor, Zachary J.; Bezner-Kerr, Wayne; Guglielmo, Christopher G.; Kopp, Gregory A.; Gurka, Roi
2013-01-01
Wing flapping is one of the most widespread propulsion methods found in nature; however, the current understanding of the aerodynamics in bird wakes is incomplete. The role of the unsteady motion in the flow and its contribution to the aerodynamics is still an open question. In the current study, the wake of a freely flying European starling has been investigated using long-duration high-speed Particle Image Velocimetry (PIV) in the near wake. Kinematic analysis of the wings and body of the bird has been performed using additional high-speed cameras that recorded the bird movement simultaneously with the PIV measurements. The wake evolution of four complete wingbeats has been characterized through reconstruction of the time-resolved data, and the aerodynamics in the wake have been analyzed in terms of the streamwise forces acting on the bird. The profile drag from classical aerodynamics was found to be positive during most of the wingbeat cycle, yet kinematic images show that the bird does not decelerate. It is shown that unsteady aerodynamics are necessary to satisfy the drag/thrust balance by approximating the unsteady drag term. These findings may shed light on the flight efficiency of birds by providing a partial answer to how they minimize drag during flapping flight. PMID:24278243
NASA Technical Reports Server (NTRS)
Spencer, B., Jr.; Fournier, R. H.
1973-01-01
An investigation has been made at Mach numbers from 1.50 to 4.63 to determine systematically the effects of the addition and position of outboard stabilizers and vertical- and vee-tail configurations on the performance and stability characteristics of a low-wave-drag elliptical body. The basic body shape was a zero-lift hypersonic minimum-wave-drag body as determined for the geometric constraints of length and volume. The elliptical cross section had an axis ratio of 2 (major axis horizontal) and an equivalent fineness ratio of 6.14. Base-mounted outboard stabilizers were at various dihedral angles from 90 deg to minus 90 deg with and without a single center-line vertical tail or a vee-tail. The angle of attack was varied from about minus 6 to 27 deg at sideslip angles of 0 and 5 deg and a constant Reynolds number of 4.58 x one million (based on body length).
NASA Technical Reports Server (NTRS)
Elchuri, V.; Pamidi, P. R.
1985-01-01
This report is a supplemental NASTRAN document for a new capability to determine the vibratory response of turbosystems subjected to aerodynamic excitation. Supplements of NASTRAN Theoretical, User's, Programmer's, and Demonstration Manuals are included. Turbosystems such as advanced turbopropellers with highly swept blades, and axial-flow compressors and turbines can be analyzed using this capability, which has been developed and implemented in the April 1984 release of the general purpose finite element program NASTRAN. The dynamic response problem is addressed in terms of the normal modal coordinates of these tuned rotating cyclic structures. Both rigid and flexible hubs/disks are considered. Coriolis and centripetal accelerations, as well as differential stiffness effects are included. Generally nonuniform steady inflow fields and uniform flow fields arbitrarily inclined at small angles with respect to the axis of rotation of the turbosystem are considered as the sources of aerodynamic excitation. The spatial nonuniformities are considered to be small deviations from a principally uniform inflow. Subsonic relative inflows are addressed, with provision for linearly interpolating transonic airloads.
Flathers, M.B.; Bache, G.E.
1999-10-01
Radial loads and direction of a centrifugal gas compressor containing a high specific speed mixed flow impeller and a single tongue volute were determined both experimentally and computationally at both design and off-design conditions. The experimental methodology was developed in conjunction with a traditional ASME PTC-10 closed-loop test to determine radial load and direction. The experimental study is detailed in Part 1 of this paper (Moore and Flathers, 1998). The computational method employs a commercially available, fully three-dimensional viscous code to analyze the impeller and the volute interaction. An uncoupled scheme was initially used where the impeller and volute were analyzed as separate models using a common vaneless diffuser geometry. The two calculations were then repeated until the boundary conditions at a chosen location in the common vaneless diffuser were nearly the same. Subsequently, a coupled scheme was used where the entire stage geometry was analyzed in one calculation, thus eliminating the need for manual iteration of the two independent calculations. In addition to radial load and direction information, this computational procedure also provided aerodynamic stage performance. The effect of impeller front face and rear face cavities was also quantified. The paper will discuss computational procedures, including grid generation and boundary conditions, as well as comparisons of the various computational schemes to experiment. The results of this study will show the limitations and benefits of Computational Fluid Dynamics (CFD) for determination of radial load, direction, and aerodynamic stage performance.
Langley Symposium on Aerodynamics, volume 1
NASA Technical Reports Server (NTRS)
Stack, Sharon H. (Compiler)
1986-01-01
The purpose of this work was to present current work and results of the Langley Aeronautics Directorate covering the areas of computational fluid dynamics, viscous flows, airfoil aerodynamics, propulsion integration, test techniques, and low-speed, high-speed, and transonic aerodynamics. The following sessions are included in this volume: theoretical aerodynamics, test techniques, fluid physics, and viscous drag reduction.
Aerodynamics Research Revolutionizes Truck Design
NASA Technical Reports Server (NTRS)
2008-01-01
During the 1970s and 1980s, researchers at Dryden Flight Research Center conducted numerous tests to refine the shape of trucks to reduce aerodynamic drag and improved efficiency. During the 1980s and 1990s, a team based at Langley Research Center explored controlling drag and the flow of air around a moving body. Aeroserve Technologies Ltd., of Ottawa, Canada, with its subsidiary, Airtab LLC, in Loveland, Colorado, applied the research from Dryden and Langley to the development of the Airtab vortex generator. Airtabs create two counter-rotating vortices to reduce wind resistance and aerodynamic drag of trucks, trailers, recreational vehicles, and many other vehicles.
The impact of lift and drag on 6DOF motion of LEO objects : formation control and debris behaviour
NASA Astrophysics Data System (ADS)
Smith, Brenton; Boyce, Russell; Brown, Melrose
2016-07-01
Perturbing forces on spacecraft are a challenge for the establishment and maintenance of satellite formations. For large satellites, the use of thrusters is a practical means of countering perturbing forces. However, long-term thrusting is not currently feasible for miniaturised satellites due to volume and mass constraints. Astrodynamics effects - in particular, passive aerodynamic lift and drag forces - are possible means for miniaturised satellites to maintain a formation in Low Earth Orbit (LEO). Currently, lift and drag for rendezvous have been considered in the presence of simplified orbital models, namely two body motion with the J2 effect. Given the small magnitude of lift and drag in LEO, it is unclear as to the control effectiveness of these aerodynamic forces under all orbital perturbations including solar radiation pressure, third body gravitation, and the non-spherical gravity. The work presented here will explore the extent to which aerodynamic lift and drag can be utilised for formation establishment and maintenance under changing operating conditions, including altitude, orbital inclination, space weather, sensor errors, and all-encompassing orbital perturbations. This work applies an in-house developed orbital propagation code to simulate the motion of formation flying spacecraft under differing conditions. The results will help miniaturised satellite formation flight planners better plan and operate future formation missions, and will also feed into improved understanding of the 6DOF motion of near-Earth orbit objects, including that of uncontrolled objects such as space debris.
NASA Technical Reports Server (NTRS)
Weihs, D.; Katz, J.
1986-01-01
In the present treatment of the calculation of forces on a wing that is suddenly brought into motion at a constant speed, attention is given to the unsteady potential's contribution to the force balance. Total bound vorticity is produced at the initial impulse. The results obtained are independent of wing aspect ratio; as time increases, this effect on the drag force becomes smaller as the vortex emanating from the trailing edge is left behind. The second contributor to induced drag is the spanwise vorticity shedding that results from the spanwise load distribution of three-dimensional wings. This contribution grows with time as the length of the wake grows.
NASA Astrophysics Data System (ADS)
Milne, Andrew J. B.; Fleck, Brian; Nobes, David; Sen, Debjyoti; Amirfazli, Alidad; University of Alberta Mechanical Engineering Collaboration
2013-11-01
We present the first ever direct measurements of the coefficient of drag on sessile drops at Reynolds numbers from the creeping flow regime up to the point of incipient motion, made using a newly developed floating element differential drag sensor. Surfaces of different wettabilities (PMMA, Teflon, and a superhydrophobic surface (SHS)), wet by water, hexadecane, and various silicone oils, are used to study the effects of drop shape, and fluid properties on drag. The relation between drag coefficient and Reynolds number (scaled by drop height) varies slightly with liquid-solid system and drop volume with results suggesting the drop experiences increased drag compared to similar shaped solid bodies due to drop oscillation influencing the otherwise laminar flow. Drops adopting more spherical shapes are seen to experience the greatest force at any given airspeed. This indicates that the relative exposed areas of drops is an important consideration in terms of force, with implications for the shedding of drops in applications such as airfoil icing and fuel cell flooding. The measurement technique used in this work can be adapted to measure drag force on other deformable, lightly adhered objects such as dust, sand, snow, vesicles, foams, and biofilms. The authours acknowledge NSERC, Alberta Innovates Technology Futures, and the Killam Trusts.
Baseball Aerodynamics: What do we know and how do we know it?
NASA Astrophysics Data System (ADS)
Nathan, Alan
2009-11-01
Baseball aerodynamics is governed by three phenomenological quantities: the coefficients of drag, lift, and moment, the latter determining the spin decay time constant. In past years, these quantities were studied mainly in wind tunnel experiments, whereby the forces on the baseball are measured directly. More recently, new tools are being used that focus on measuring accurate baseball trajectories, from which the forces can be inferred. These tools include high-speed motion analysis, video tracking of pitched baseballs (the PITCHf/x system), and Doppler radar tracking. In this contribution, I will discuss what these new tools are teaching us about baseball aerodynamics.
Aerodynamic performance due to forewing and hindwing interaction in gliding dragonfly flight
NASA Astrophysics Data System (ADS)
Zhang, Jie; Lu, Xi-Yun
2009-07-01
Aerodynamic performance due to forewing and hindwing interaction in gliding dragonfly flight has been studied using a multiblock lattice Boltzmann method. We find that the interactions between forewing and hindwing effectively enhance the total lift force and reduce the drag force on the wings compared to two independent wings. The interaction mechanism may be associated with the triangular camber effect by modulating the relative arrangement of the forewing and hindwing. The results obtained in this Brief Report provide physical insight into the understanding of aerodynamic behaviors for gliding dragonfly flight.
Aerodynamic Performances of Corrugated Dragonfly Wings at Low Reynolds Numbers
NASA Astrophysics Data System (ADS)
Tamai, Masatoshi; He, Guowei; Hu, Hui
2006-11-01
The cross-sections of dragonfly wings have well-defined corrugated configurations, which seem to be not very suitable for flight according to traditional airfoil design principles. However, previous studies have led to surprising conclusions of that corrugated dragonfly wings would have better aerodynamic performances compared with traditional technical airfoils in the low Reynolds number regime where dragonflies usually fly. Unlike most of the previous studies of either measuring total aerodynamics forces (lift and drag) or conducting qualitative flow visualization, a series of wind tunnel experiments will be conducted in the present study to investigate the aerodynamic performances of corrugated dragonfly wings at low Reynolds numbers quantitatively. In addition to aerodynamics force measurements, detailed Particle Image Velocimetry (PIV) measurements will be conducted to quantify of the flow field around a two-dimensional corrugated dragonfly wing model to elucidate the fundamental physics associated with the flight features and aerodynamic performances of corrugated dragonfly wings. The aerodynamic performances of the dragonfly wing model will be compared with those of a simple flat plate and a NASA low-speed airfoil at low Reynolds numbers.
NASA Astrophysics Data System (ADS)
Isaev, S. A.; Sudakov, A. G.; Zhukova, Yu. V.; Usachovd, A. E.
2014-07-01
An analysis of the physical processes in unsteady fl ow past a circular cylinder surrounded by a sheath with ports for bleeding of the medium has been made by a factorized fi nite-volume method on the basis of numerical solution of Navier-Stokes equations closed with the Menter sheer-stress-transfer model. It has been shown that such arrangement of a circular cylinder ensures stabilization of the wake of the cylinder, and also the reduction in its drag and cessation of the action of an alternating transverse force at Reynolds numbers higher than 105.
Aerodynamic analysis of a helicopter fuselage with rotating rotor head
NASA Astrophysics Data System (ADS)
Reß, R.; Grawunder, M.; Breitsamter, Ch.
2015-06-01
The present paper describes results of wind tunnel experiments obtained during a research programme aimed at drag reduction of the fuselage of a twin engine light helicopter configuration. A 1 : 5 scale model of a helicopter fuselage including a rotating rotor head and landing gear was investigated in the low-speed wind tunnel A of Technische Universität a München (TUM). The modelled parts of the helicopter induce approxiu mately 80% of the total parasite drag thus forming a major potential for shape optimizations. The present paper compares results of force and moment measurements of a baseline configuration and modified variants with an emphasis on the aerodynamic drag, lift, and yawing moment coefficients.
Feedback Control of a Square-Back Ahmed Body Flow for Form-Drag Reduction
NASA Astrophysics Data System (ADS)
Evstafyeva, Olga; Morgans, Aimee
2015-11-01
Road transport accounts for roughly 22% of CO2 emissions worldwide, and at highway speeds two thirds of usable energy is consumed overcoming aerodynamic drag. For square-back vehicles, aerodynamic drag is dominated by form- drag, originating from pressure difference between the front and the back face (base) of the vehicle. This study explores using feedback control to increase mean base pressure and thus reduce the form-drag of 3D Ahmed body flows at low (laminar) and medium (transitioning to turbulence) Reynolds numbers. Using Large Eddy Simulations as a test-bed, a linear control strategy to attenuate base-pressure force fluctuations is investigated. Body-mounted sensing and actuation is used: sensing of the base pressure force fluctuations, and actuation of a zero-mean slot jet just ahead of the base. The dynamic linearity of the response to actuation is tested and a feedback controller then designed using frequency domain harmonic forcing system identification data. Recent advances in understanding of the Ahmed body wake dynamics such as top-to-bottom and left-to-right bi-stable behaviour, are considered in the feedback control implementation.
Aerodynamic characteristics of flying fish in gliding flight.
Park, Hyungmin; Choi, Haecheon
2010-10-01
The flying fish (family Exocoetidae) is an exceptional marine flying vertebrate, utilizing the advantages of moving in two different media, i.e. swimming in water and flying in air. Despite some physical limitations by moving in both water and air, the flying fish has evolved to have good aerodynamic designs (such as the hypertrophied fins and cylindrical body with a ventrally flattened surface) for proficient gliding flight. Hence, the morphological and behavioral adaptations of flying fish to aerial locomotion have attracted great interest from various fields including biology and aerodynamics. Several aspects of the flight of flying fish have been determined or conjectured from previous field observations and measurements of morphometric parameters. However, the detailed measurement of wing performance associated with its morphometry for identifying the characteristics of flight in flying fish has not been performed yet. Therefore, in the present study, we directly measure the aerodynamic forces and moment on darkedged-wing flying fish (Cypselurus hiraii) models and correlated them with morphological characteristics of wing (fin). The model configurations considered are: (1) both the pectoral and pelvic fins spread out, (2) only the pectoral fins spread with the pelvic fins folded, and (3) both fins folded. The role of the pelvic fins was found to increase the lift force and lift-to-drag ratio, which is confirmed by the jet-like flow structure existing between the pectoral and pelvic fins. With both the pectoral and pelvic fins spread, the longitudinal static stability is also more enhanced than that with the pelvic fins folded. For cases 1 and 2, the lift-to-drag ratio was maximum at attack angles of around 0 deg, where the attack angle is the angle between the longitudinal body axis and the flying direction. The lift coefficient is largest at attack angles around 30∼35 deg, at which the flying fish is observed to emerge from the sea surface. From glide polar
The Aerodynamic Forces on Slender Plane- and Cruciform-Wing and Body Combinations
NASA Technical Reports Server (NTRS)
Spreiter, John R
1950-01-01
The load distribution, forces, and moments are calculated theoretically for inclined slender wing-body combinations consisting of a slender body of revolution and either a plane or cruciform arrangement of low-aspect-ratio pointed wings. The results are applicable at subsonic and transonic speeds, and at supersonic speeds, provided the entire wing-body combination lies near the center of the Mach cone.
Aerodynamic Optimization of Supersonic Transport at Near-Sonic Regime
NASA Astrophysics Data System (ADS)
Yamazaki, Wataru; Matsushima, Kisa; Obayashi, Shigeru; Nakahashi, Kazuhiro
Recently, an airplane cruising at near-sonic regime is watched with keen interest. The Sonic-Cruiser, of which the Boeing Company has examined and challenged the development, is the most remarkable case. In this paper, motivated by this trend, aerodynamic performance optimization for an airplane cruising at near-sonic regime is discussed based on CFD simulations. NAL’s experimental supersonic airplane, called NEXST-1, was employed as the baseline model for optimization. Aerodynamic performance was evaluated by solving the Euler equations with the unstructured grid method. It was confirmed that the performance Euler simulation predicted was qualitatively correct. By the evaluation to select a baseline model for optimization, NEXST-1 was accepted as a candidate of sonic plane because of the existence of drag bucket at near-sonic regime. In the optimization, Genetic Algorithm was used with Euler simulations. The objective was to reduce drag keeping lift constant, at the flying speed of Mach 0.98. The optimized result showed L/D improvement not only for near-sonic regime but also for transonic regime. The mechanism of design to reduce drag force was found through the analysis and comparison of the geometries and aerodynamic phenomena about the baseline model and the optimized one.
NASA Astrophysics Data System (ADS)
Krafcik, Andrej; Babinec, Peter; Frollo, Ivan
2015-04-01
Magnetic targeting of drugs attached to magnetic nanoparticles with diameter ≈ 100 nm after their intravenous administration is an interesting method of drug delivery widely investigated both theoretically as well as experimentally. Our aim in this study is theoretical analysis of a magnetic aerosol targeting to the lung. Due to lung anatomy magnetic particles up to 5 μm can be safely used, therefore the magnetic force would be stronger, moreover drag force exerted on the particle is according to Stokes law linearly dependent on the viscosity, would be weaker, because the viscosity of the air in the lung is approximately 200 fold smaller than viscosity of the blood. Lung therefore represents unique opportunity for magnetic drug targeting, as we have shown in this study by the analysis of magnetic particle dynamics in a rhythmically expanding and contracting distal and proximal alveolus subjected to high-gradient magnetic field generated by quadrupolar permanent Halbach magnet array.
The Effect of Volumetric Porosity on Roughness Element Drag
NASA Astrophysics Data System (ADS)
Gillies, John; Nickling, William; Nikolich, George; Etyemezian, Vicken
2016-04-01
Much attention has been given to understanding how the porosity of two dimensional structures affects the drag force exerted by boundary-layer flow on these flow obstructions. Porous structures such as wind breaks and fences are typically used to control the sedimentation of sand and snow particles or create micro-habitats in their lee. Vegetation in drylands also exerts control on sediment transport by wind due to aerodynamic effects and interaction with particles in transport. Recent research has also demonstrated that large spatial arrays of solid three dimensional roughness elements can be used to reduce sand transport to specified targets for control of wind erosion through the effect of drag partitioning and interaction of the moving sand with the large (>0.3 m high) roughness elements, but porous elements may improve the effectiveness of this approach. A thorough understanding of the role porosity plays in affecting the drag force on three-dimensional forms is lacking. To provide basic understanding of the relationship between the porosity of roughness elements and the force of drag exerted on them by fluid flow, we undertook a wind tunnel study that systematically altered the porosity of roughness elements of defined geometry (cubes, rectangular cylinders, and round cylinders) and measured the associated change in the drag force on the elements under similar Reynolds number conditions. The elements tested were of four basic forms: 1) same sized cubes with tubes of known diameter milled through them creating three volumetric porosity values and increasing connectivity between the tubes, 2) cubes and rectangular cylinders constructed of brass screen that nested within each other, and 3) round cylinders constructed of brass screen that nested within each other. The two-dimensional porosity, defined as the ratio of total surface area of the empty space to the solid surface area of the side of the element presented to the fluid flow was conserved at 0.519 for
NASA Technical Reports Server (NTRS)
Reddy, T. S. R.; Srivastava, R.
1996-01-01
This guide describes the input data required for using MSAP2D (Multi Stage Aeroelastic analysis Program - Two Dimensional) computer code. MSAP2D can be used for steady, unsteady aerodynamic, and aeroelastic (flutter and forced response) analysis of bladed disks arranged in multiple blade rows such as those found in compressors, turbines, counter rotating propellers or propfans. The code can also be run for single blade row. MSAP2D code is an extension of the original NPHASE code for multiblade row aerodynamic and aeroelastic analysis. Euler equations are used to obtain aerodynamic forces. The structural dynamic equations are written for a rigid typical section undergoing pitching (torsion) and plunging (bending) motion. The aeroelastic equations are solved in time domain. For single blade row analysis, frequency domain analysis is also provided to obtain unsteady aerodynamic coefficients required in an eigen analysis for flutter. In this manual, sample input and output are provided for a single blade row example, two blade row example with equal and unequal number of blades in the blade rows.
Supersonic Aerodynamic Characteristics of Blunt Body Trim Tab Configurations
NASA Technical Reports Server (NTRS)
Korzun, Ashley M.; Murphy, Kelly J.; Edquist, Karl T.
2013-01-01
Trim tabs are aerodynamic control surfaces that can allow an entry vehicle to meet aerodynamic performance requirements while reducing or eliminating the use of ballast mass and providing a capability to modulate the lift-to-drag ratio during entry. Force and moment data were obtained on 38 unique, blunt body trim tab configurations in the NASA Langley Research Center Unitary Plan Wind Tunnel. The data were used to parametrically assess the supersonic aerodynamic performance of trim tabs and to understand the influence of tab area, cant angle, and aspect ratio. Across the range of conditions tested (Mach numbers of 2.5, 3.5, and 4.5; angles of attack from -4deg to +20deg; angles of sideslip from 0deg to +8deg), the effects of varying tab area and tab cant angle were found to be much more significant than effects from varying tab aspect ratio. Aerodynamic characteristics exhibited variation with Mach number and forebody geometry over the range of conditions tested. Overall, the results demonstrate that trim tabs are a viable approach to satisfy aerodynamic performance requirements of blunt body entry vehicles with minimal ballast mass. For a 70deg sphere-cone, a tab with 3% area of the forebody and canted approximately 35deg with no ballast mass was found to give the same trim aerodynamics as a baseline model with ballast mass that was 5% of the total entry mass.
Eshed, L.; Yaron, S.; Dosoretz, C. G.
2008-01-01
The effect of permeate flux on the development of a biofouling layer on cross-flow separation membranes was studied by using a bench-scale system consisting of two replicate 100-molecular-weight-cutoff tubular ultrafiltration membrane modules, one that allowed flow of permeate and one that did not (control). The system was inoculated with Pseudomonas putida S-12 tagged with a red fluorescent protein and was operated using a laminar flow regimen under sterile conditions with a constant feed of diluted (1:75) Luria-Bertani medium. Biofilm development was studied by using field emission scanning electron microscopy and confocal scanning laser microscopy and was subsequently quantified by image analysis, as well as by determining live counts and by permeate flux monitoring. Biofilm development was highly enhanced in the presence of permeate flow, which resulted in the buildup of complex three-dimensional structures on the membrane. Bacterial transport toward the membrane by permeate drag was found to be a mechanism by which cross-flow filtration contributes to the buildup of a biofouling layer that was more dominant than transport of nutrients. Cellular viability was found to be not essential for transport and adhesion under cross-flow conditions, since the permeate drag overcame the effect of bacterial motility. PMID:18931284
Moore, J.J.; Flathers, M.B.
1998-04-01
Net radial loading arising from asymmetric pressure fields in the volutes of centrifugal pumps during off-design operation is well known and has been studied extensively. In order to achieve a marked improvement in overall efficiency in centrifugal gas compressors, vaneless volute diffusers are matched to specific impellers to yield improved performance over a wide application envelope. As observed in centrifugal pumps, nonuniform pressure distributions that develop during operation above and below the design flow create static radial loads on the rotor. In order to characterize these radial forces, a novel experimental measurement and post-processing technique is employed that yields both the magnitude and direction of the load by measuring the shaft centerline locus in the tilt-pad bearings. The method is applicable to any turbomachinery operating on fluid film radial bearings equipped with proximity probes. The forces are found to be a maximum near surge and increase with higher pressures and speeds. The results are nondimensionalized, allowing the radial loading for different operating conditions to be predicted.
Aerodynamics of a golf ball with grooves
NASA Astrophysics Data System (ADS)
Kim, Jooha; Son, Kwangmin; Choi, Haecheon
2009-11-01
It is well known that the drag on a dimpled ball is much lower than that on smooth ball. Choi et al. (Phys. Fluids, 2006) showed that turbulence is generated through the instability of shear layer separating from the edge of dimples and delays flow separation. Based on this mechanism, we devise a new golf ball with grooves on the surface but without any dimples. To investigate the aerodynamic performance of this new golf ball, an experiment is conducted in a wind tunnel at the Reynolds numbers of 0.5 x10^5 - 2.7 x10^5 and the spin ratios (ratio of surface velocity to the free-stream velocity) of α=0 - 0.5, which are within the ranges of real golf-ball velocity and spin rate. We measure the drag and lift forces on the grooved ball and compare them with those of smooth ball. At zero spin, the drag coefficient on the grooved ball shows a rapid fall-off at a critical Reynolds number and maintains a minimum value which is lower by 50% than that on smooth ball. At non-zero α, the drag coefficient on the grooved ball increases with increasing α, but is still lower by 40% than that on smooth ball. The lift coefficient on the grooved ball increases with increasing α, and is 100% larger than that on smooth ball. The aerodynamic characteristics of grooved ball is in general quite similar to that of dimpled ball. Some more details will be discussed in the presentation.
GASP- General Aviation Synthesis Program. Volume 3: Aerodynamics
NASA Technical Reports Server (NTRS)
Hague, D.
1978-01-01
Aerodynamics calculations are treated in routines which concern moments as they vary with flight conditions and attitude. The subroutines discussed: (1) compute component equivalent flat plate and wetted areas and profile drag; (2) print and plot low and high speed drag polars; (3) determine life coefficient or angle of attack; (4) determine drag coefficient; (5) determine maximum lift coefficient and drag increment for various flap types and flap settings; and (6) determine required lift coefficient and drag coefficient in cruise flight.
Advanced Aerodynamic Control Effectors
NASA Technical Reports Server (NTRS)
Wood, Richard M.; Bauer, Steven X. S.
1999-01-01
A 1990 research program that focused on the development of advanced aerodynamic control effectors (AACE) for military aircraft has been reviewed and summarized. Data are presented for advanced planform, flow control, and surface contouring technologies. The data show significant increases in lift, reductions in drag, and increased control power, compared to typical aerodynamic designs. The results presented also highlighted the importance of planform selection in the design of a control effector suite. Planform data showed that dramatic increases in lift (greater than 25%) can be achieved with multiple wings and a sawtooth forebody. Passive porosity and micro drag generator control effector data showed control power levels exceeding that available from typical effectors (moving surfaces). Application of an advanced planform to a tailless concept showed benefits of similar magnitude as those observed in the generic studies.
Dynamic soaring: aerodynamics for albatrosses
NASA Astrophysics Data System (ADS)
Denny, Mark
2009-01-01
Albatrosses have evolved to soar and glide efficiently. By maximizing their lift-to-drag ratio L/D, albatrosses can gain energy from the wind and can travel long distances with little effort. We simplify the difficult aerodynamic equations of motion by assuming that albatrosses maintain a constant L/D. Analytic solutions to the simplified equations provide an instructive and appealing example of fixed-wing aerodynamics suitable for undergraduate demonstration.
NASA Technical Reports Server (NTRS)
Coe, P. L., Jr.
1979-01-01
The overall aerodynamic drag characteristics of a conventional wheelchair were defined and the individual drag contributions of its components were determined. The results show that a fiftieth percentile man sitting in the complete wheelchair would experience an aerodynamic drag coefficient on the order of 1.4.
Transient platoon aerodynamics and bluff body flows
NASA Astrophysics Data System (ADS)
Tsuei, Lun
There are two components of this experimental work: transient vehicle platoon aerodynamics and bluff-body flows. The transient aerodynamic effects in a four-vehicle platoon during passing maneuvers and in-line oscillations are investigated. A vehicle model is moved longitudinally parallel to a four-car platoon to simulate passing maneuvers. The drag and side forces experienced by each platoon member are measured using strain gauge balances. The resulting data are presented as dimensionless coefficients. It is shown that each car in the platoon experiences a repulsive side force when the passing vehicle is in the neighborhood of its rear half. The side force reverses its direction and becomes an attractive force when the passing vehicle moves to the neighborhood of its front half. The drag force experienced by each platoon member is increased when the passing vehicle is in its proximity. The effects of the lateral spacing and relative velocity between the platoon and the passing vehicle, as well as the shape of the passing vehicle, are also investigated. Similar trends are observed in simulations of both a vehicle passing a platoon and a platoon overtaking a vehicle. During the in-line oscillation experiments, one of the four platoon members is forced to undergo longitudinal periodic motions. The drag force experienced by each platoon member is determined simultaneously during the oscillations. The effects of the location of the oscillating vehicle, the shape of the vehicles and the displacement and velocity amplitudes of the oscillation are examined. The results from the transient conditions are compared to those from the steady tests in the same setup. In the case of a four-car platoon, the drag variations experienced by the vehicles adjacent to the oscillating vehicle are discussed using a cavity model. It is found that when the oscillating car moves forward and approaches its upstream neighbor, itself and its downstream neighbor experiences an increased drag
NASA Astrophysics Data System (ADS)
Narozhny, B. N.; Levchenko, A.
2016-04-01
Coulomb drag is a transport phenomenon whereby long-range Coulomb interaction between charge carriers in two closely spaced but electrically isolated conductors induces a voltage (or, in a closed circuit, a current) in one of the conductors when an electrical current is passed through the other. The magnitude of the effect depends on the exact nature of the charge carriers and the microscopic, many-body structure of the electronic systems in the two conductors. Drag measurements have become part of the standard toolbox in condensed matter physics that can be used to study fundamental properties of diverse physical systems including semiconductor heterostructures, graphene, quantum wires, quantum dots, and optical cavities.
Computational Analysis of an effect of aerodynamic pressure on the side view mirror geometry
NASA Astrophysics Data System (ADS)
Murukesavan, P.; Mu'tasim, M. A. N.; Sahat, I. M.
2013-12-01
This paper describes the evaluation of aerodynamic flow effects on side mirror geometry for a passenger car using ANSYS Fluent CFD simulation software. Results from analysis of pressure coefficient on side view mirror designs is evaluated to analyse the unsteady forces that cause fluctuations to mirror surface and image blurring. The fluctuation also causes drag forces that increase the overall drag coefficient, with an assumption resulting in higher fuel consumption and emission. Three features of side view mirror design were investigated with two input velocity parameters of 17 m/s and 33 m/s. Results indicate that the half-sphere design shows the most effective design with less pressure coefficient fluctuation and drag coefficient.
The Minimum Induced Drag of Aerofoils
NASA Technical Reports Server (NTRS)
Munk, M. M.
1979-01-01
Equations are derived to demonstrate which distribution of lifting elements result in a minimum amount of aerodynamic drag. The lifting elements were arranged (1) in one line, (2) parallel lying in a transverse plane, and (3) in any direction in a transverse plane. It was shown that the distribution of lift which causes the least drag is reduced to the solution of the problem for systems of airfoils which are situated in a plane perpendicular to the direction of flight.
Aerodynamic shape optimization of space vehicle in very-low-earth-orbit
NASA Astrophysics Data System (ADS)
Park, Jae Hyun; Myong, Rho Shin; Kim, Dong Hyun; Baek, Seung Wook
2014-12-01
Space vehicles orbiting in Very-Low-Earth-Orbit (VLEO, h = 200˜300 km) experience considerably large aerodynamic drag due to high air-density in comparison with Low-Earth-Orbit (LEO, h = 600 ˜ 700 km). Therefore, the optimization of vehicle shape via minimization of aerodynamic drag is essential for accurate estimation of satellite lifetime and fuel budget at the design stage. In this study, the aerodynamic drag is computed with direct simulation Monte Carlo (DSMC) because even in VLEO, whose free stream Knudsen number is sufficiently large, some errors are still found in the prediction using free molecular approach. In order to find the optimized configuration, we vary the shape of frontal surface normal to the flight direction. Interestingly, the effects of such geometrical change appear distinctively depending on the gas-surface interaction (GSI, diffuse or specular) which can be represented by the thermal accommodation coefficient. The satellite aerodynamic characteristics including force, torque, and thermal loading are also identified by changing the pitch and the side angle.
NASA Technical Reports Server (NTRS)
Zilz, D. E.
1985-01-01
A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to represent two different test techniques. One was a conventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a sub-scale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously. This is Volume 2 of 2: Wind Tunnel Test Force and Moment Data Report.
Projectiles and Aerodynamic Forces.
ERIC Educational Resources Information Center
Armstrong, H. L.
1984-01-01
Discusses the air resistance on projectiles, examining (in separate sections) air resistance less than gravity and air resistance greater than gravity. Also considers an approximation in which a trajectory is divided into two parts, the first part neglecting gravity and the second part neglecting the air resistance. (JN)
McLaughlin, J.B.
1992-01-01
This project has two goals, to calculate the lift force on a spherical droplet or particle that translates through a shear flow, and to measure the inertial migration velocity that is caused by the lift force. The focus of the study is on a range of Reynolds numbers that has been shown to be of importance in the inertial deposition of aerosols from turbulent shear flows. Aspects of current technical progress summarized are the asymptotic analysis, computer simulations, and experimental measurements. Future plans and resulting publications are given.
McLaughlin, J.B.
1992-11-01
This project has two goals, to calculate the lift force on a spherical droplet or particle that translates through a shear flow, and to measure the inertial migration velocity that is caused by the lift force. The focus of the study is on a range of Reynolds numbers that has been shown to be of importance in the inertial deposition of aerosols from turbulent shear flows. Aspects of current technical progress summarized are the asymptotic analysis, computer simulations, and experimental measurements. Future plans and resulting publications are given.
NASA Technical Reports Server (NTRS)
Riebe, G. D.; Small, W. J.; Morris, O. A.
1981-01-01
Results from analytical and experimental studies of the aerodynamic characteristics of a turbojet-boosted launch vehicle concept through a Mach number range of 1.50 to 2.86 are presented. The vehicle consists of a winged orbiter utilizing an area-ruled axisymmetric body and two winged turbojet boosters mounted underneath the orbiter wing. Drag characteristics near zero lift were of prime interest. Force measurements and flow visualization techniques were employed. Estimates from wave drag theory, supersonic lifting surface theory, and impact theory are compared with data and indicate the ability of these theories to adequately predict the aerodynamic characteristics of the vehicle. Despite the existence of multiple wings and bodies in close proximity to each other, no large scale effects of boundary layer separation on drag or lift could be discerned. Total drag levels were, however, sensitive to booster locations.
Aerodynamic Analysis of Simulated Heat Shield Recession for the Orion Command Module
NASA Technical Reports Server (NTRS)
Bibb, Karen L.; Alter, Stephen J.; Mcdaniel, Ryan D.
2008-01-01
The aerodynamic effects of the recession of the ablative thermal protection system for the Orion Command Module of the Crew Exploration Vehicle are important for the vehicle guidance. At the present time, the aerodynamic effects of recession being handled within the Orion aerodynamic database indirectly with an additional safety factor placed on the uncertainty bounds. This study is an initial attempt to quantify the effects for a particular set of recessed geometry shapes, in order to provide more rigorous analysis for managing recession effects within the aerodynamic database. The aerodynamic forces and moments for the baseline and recessed geometries were computed at several trajectory points using multiple CFD codes, both viscous and inviscid. The resulting aerodynamics for the baseline and recessed geometries were compared. The forces (lift, drag) show negligible differences between baseline and recessed geometries. Generally, the moments show a difference between baseline and recessed geometries that correlates with the maximum amount of recession of the geometry. The difference between the pitching moments for the baseline and recessed geometries increases as Mach number decreases (and the recession is greater), and reach a value of -0.0026 for the lowest Mach number. The change in trim angle of attack increases from approx. 0.5deg at M = 28.7 to approx. 1.3deg at M = 6, and is consistent with a previous analysis with a lower fidelity engineering tool. This correlation of the present results with the engineering tool results supports the continued use of the engineering tool for future work. The present analysis suggests there does not need to be an uncertainty due to recession in the Orion aerodynamic database for the force quantities. The magnitude of the change in pitching moment due to recession is large enough to warrant inclusion in the aerodynamic database. An increment in the uncertainty for pitching moment could be calculated from these results and
Investigation of the transient aerodynamic phenomena associated with passing manoeuvres
NASA Astrophysics Data System (ADS)
Noger, C.; Regardin, C.; Széchényi, E.
2005-11-01
Passing manoeuvres and crosswind can have significant effects on the stability of road vehicles. The transient aerodynamics, which interacts with suspension, steering geometry and driver reaction is not well understood. When two vehicles overtake or cross, they mutually influence the flow field around each other, and under certain conditions, can generate severe gust loads that act as additional forces on both vehicles. The transient forces acting on them are a function of the longitudinal and transverse spacings and of the relative velocity between the two vehicles. Wind tunnel experiments have been conducted in one of the automotive wind tunnels of the Institut Aérotechnique of Saint-Cyr l’École to simulate the transient overtaking process between two models of a simple generic automobile shape. The tests were designed to study the effects of various parameters such as the longitudinal and transverse spacing, the relative velocity and the crosswind on the aerodynamic forces and moments generated on the overtaken and overtaking vehicles. Test results characterize the transient aerodynamic side force as well as the yawing moment coefficients in terms of these parameters. Measurements of the drag force coefficient as well as the static pressure distribution around the overtaken vehicle complete the understanding. The main results indicate the aerodynamic coefficients of the overtaken vehicle to be velocity independent within the limit of the test parameters, while unsteady aerodynamic effects appear in the case of an overtaking vehicle. The mutual interference effects between the vehicles vary as a linear function of the transverse spacing and the crosswind does not really generate any new unsteady behaviour.
Drag evaluation of the Bellanca Skyrocket II
NASA Technical Reports Server (NTRS)
Gregorek, G. M.; Hoffmann, M. J.; Payne, H. E.; Harris, J. P.
1977-01-01
The Bellanca Skyrocket II, possessor of five world speed records, is a single engine aircraft with high performance that has been attributed to a laminar flow airfoil and an all composite structure. Utilization of composite materials in the Skyrocket II is unique since this selection was made to increase the aerodynamic efficiency of the aircraft. Flight tests are in progress to measure the overall aircraft drag and the wing section drag for comparison with the predicted performance of the Skyrocket. Initial results show the zero lift drag is indeed low, equalling 0.016.
Ciufolini, Ignazio
2007-09-01
The origin of inertia has intrigued scientists and philosophers for centuries. Inertial frames of reference permeate our daily life. The inertial and centrifugal forces, such as the pull and push that we feel when our vehicle accelerates, brakes and turns, arise because of changes in velocity relative to uniformly moving inertial frames. A classical interpretation ascribed these forces to acceleration relative to some absolute frame independent of the cosmological matter, whereas an opposite view related them to acceleration relative to all the masses and 'fixed stars' in the Universe. An echo and partial realization of the latter idea can be found in Einstein's general theory of relativity, which predicts that a spinning mass will 'drag' inertial frames along with it. Here I review the recent measurements of frame dragging using satellites orbiting Earth. PMID:17805287
Dynamic Soaring: Aerodynamics for Albatrosses
ERIC Educational Resources Information Center
Denny, Mark
2009-01-01
Albatrosses have evolved to soar and glide efficiently. By maximizing their lift-to-drag ratio "L/D", albatrosses can gain energy from the wind and can travel long distances with little effort. We simplify the difficult aerodynamic equations of motion by assuming that albatrosses maintain a constant "L/D". Analytic solutions to the simplified…
Sykes, Andrew G.; Davis, Matthew J.; Roberts, David C.
2009-08-21
The existence of frictionless flow below a critical velocity for obstacles moving in a superfluid is well established in the context of the mean-field Gross-Pitaevskii theory. We calculate the next order correction due to quantum and thermal fluctuations and find a nonzero force acting on a delta-function impurity moving through a quasi-one-dimensional Bose-Einstein condensate at all subcritical velocities and at all temperatures. The force occurs due to an imbalance in the Doppler shifts of reflected quantum fluctuations from either side of the impurity. Our calculation is based on a consistent extension of Bogoliubov theory to second order in the interaction strength, and finds new analytical solutions to the Bogoliubov-de Gennes equations for a gray soliton. Our results raise questions regarding the quantum dynamics in the formation of persistent currents in superfluids.
Ontogeny of lift and drag production in ground birds
Heers, Ashley M.; Tobalske, Bret W.; Dial, Kenneth P.
2011-01-01
The juvenile period is often a crucial interval for selective pressure on locomotor ability. Although flight is central to avian biology, little is known about factors that limit flight performance during development. To improve understanding of flight ontogeny, we used a propeller (revolving wing) model to test how wing shape and feather structure influence aerodynamic performance during development in the precocial chukar partridge (Alectoris chukar, 4 to >100 days post hatching). We spun wings in mid-downstroke posture and measured lift (L) and drag (D) using a force plate upon which the propeller assembly was mounted. Our findings demonstrate a clear relationship between feather morphology and aerodynamic performance. Independent of size and velocity, older wings with stiffer and more asymmetrical feathers, high numbers of barbicels and a high degree of overlap between barbules generate greater L and L:D ratios than younger wings with flexible, relatively symmetrical and less cohesive feathers. The gradual transition from immature feathers and drag-based performance to more mature feathers and lift-based performance appears to coincide with ontogenetic transitions in locomotor capacity. Younger birds engage in behaviors that require little aerodynamic force and that allow D to contribute to weight support, whereas older birds may expand their behavioral repertoire by flapping with higher tip velocities and generating greater L. Incipient wings are, therefore, uniquely but immediately functional and provide flight-incapable juveniles with access to three-dimensional environments and refugia. Such access may have conferred selective advantages to theropods with protowings during the evolution of avian flight. PMID:21307057
Roberts, David C
2008-01-01
The article considers the dramatic phenomenon of seemingly frictionless flow of slow-moving superfluids. Specifically the question of whether an object in a superfluid flow experiences any drag force is addressed. A brief account is given of the history of this problem and it is argued that recent advances in ultracold atomic physics can shed much new light on this problem. The article presents the commonly held notion that sufficiently slow-moving superfluids can flow without drag and also discusses research suggesting that scattering quantum fluctuations might cause drag in a superfluid moving at any speed.
The economic impact of drag in general aviation
NASA Technical Reports Server (NTRS)
Neal, R. D.
1975-01-01
General aviation aircraft fuel consumption and operating costs are closely linked to drag reduction methods. Improvements in airplane drag are envisioned for new models; their effects will be in the 5 to 10% range. Major improvements in fuel consumption over existing turbofan airplanes will be the combined results of improved aerodynamics plus additional effects from advanced turbofan engine designs.
Aerodynamic characteristics of sixteen electric, hybrid, and subcompact vehicles
NASA Technical Reports Server (NTRS)
Kurtz, D. W.
1979-01-01
An elementary electric and hybrid vehicle aerodynamic data base was developed using data obtained on sixteen electric, hybrid, and sub-compact production vehicles tested in the Lockheed-Georgia low-speed wind tunnel. Zero-yaw drag coefficients ranged from a high of 0.58 for a boxey delivery van and an open roadster to a low of about 0.34 for a current four-passenger proto-type automobile which was designed with aerodynamics as an integrated parameter. Vehicles were tested at yaw angles up to 40 degrees and a wing weighting analysis is presented which yields a vehicle's effective drag coefficient as a function of wing velocity and driving cycle. Other parameters investigated included the effects of windows open and closed, radiators open and sealed, and pop-up headlights. Complete six-component force and moment data are presented in both tabular and graphical formats. Only limited commentary is offered since, by its very nature, a data base should consist of unrefined reference material. A justification for pursuing efficient aerodynamic design of EHVs is presented.
NASA Technical Reports Server (NTRS)
Capone, F. J.
1975-01-01
An investigation was conducted in the Langley 16-foot transonic tunnel to determine the induced lift characteristics of a vectored thrust concept in which a rectangular jet exhaust nozzle was located in the fuselage at the wing trailing edge. The effects of nozzle deflection angles of 0 deg to 45 deg were studied at Mach numbers from 0.4 to 1.2, at angles of attack up to 14 deg, and with thrust coefficients up to 0.35. Separate force balances were used to determine total aerodynamic and thrust forces as well as thrust forces which allowed a direct measurement of jet turning angle at forward speeds. Wing pressure loading and flow characteristics using oil flow techniques were also studied.
Helicopter fuselage drag - combined computational fluid dynamics and experimental studies
NASA Astrophysics Data System (ADS)
Batrakov, A.; Kusyumov, A.; Mikhailov, S.; Pakhov, V.; Sungatullin, A.; Valeev, M.; Zherekhov, V.; Barakos, G.
2015-06-01
In this paper, wind tunnel experiments are combined with Computational Fluid Dynamics (CFD) aiming to analyze the aerodynamics of realistic fuselage configurations. A development model of the ANSAT aircraft and an early model of the AKTAI light helicopter were employed. Both models were tested at the subsonic wind tunnel of KNRTU-KAI for a range of Reynolds numbers and pitch and yaw angles. The force balance measurements were complemented by particle image velocimetry (PIV) investigations for the cases where the experimental force measurements showed substantial unsteadiness. The CFD results were found to be in fair agreement with the test data and revealed some flow separation at the rear of the fuselages. Once confidence on the CFD method was established, further modifications were introduced to the ANSAT-like fuselage model to demonstrate drag reduction via small shape changes.
NASA Technical Reports Server (NTRS)
Hemsch, Michael J. (Editor); Nielsen, Jack N. (Editor)
1986-01-01
The present conference on tactical missile aerodynamics discusses autopilot-related aerodynamic design considerations, flow visualization methods' role in the study of high angle-of-attack aerodynamics, low aspect ratio wing behavior at high angle-of-attack, supersonic airbreathing propulsion system inlet design, missile bodies with noncircular cross section and bank-to-turn maneuvering capabilities, 'waverider' supersonic cruise missile concepts and design methods, asymmetric vortex sheding phenomena from bodies-of-revolution, and swept shock wave/boundary layer interaction phenomena. Also discussed are the assessment of aerodynamic drag in tactical missiles, the analysis of supersonic missile aerodynamic heating, the 'equivalent angle-of-attack' concept for engineering analysis, the vortex cloud model for body vortex shedding and tracking, paneling methods with vorticity effects and corrections for nonlinear compressibility, the application of supersonic full potential method to missile bodies, Euler space marching methods for missiles, three-dimensional missile boundary layers, and an analysis of exhaust plumes and their interaction with missile airframes.
NASA Astrophysics Data System (ADS)
Yoon, Dong-Hee; Kohama, Yasuaki; Kikuchi, Satoshi; Kato, Takuma
Aero-train is a new driving concept using aerodynamic technology under development by the Kohama Laboratory, Institute of Fluid Science, Tohoku University. It employs the wing-in-ground effect to enable travel at high speeds over land. Aero-train makes use of the ground effects of lift and side force between the wings and a U-shaped guideway for stability. The main wings have vertical wings at the tips, which are arranged in tandem to regulate the roll and yaw stability in the U-shaped guideway. However, the vertical wings deteriorate the lift-to-drag ratio of the Aero-train by aerodynamic interaction with the main wings. The present study was performed to improve the aerodynamic performance of the Aero-train by controlling wing-wing interaction. Installation of a single-slotted flap on the wings considerably improved the aerodynamic performance of the wings.
Assessment of dual-point drag reduction for an executive-jet modified airfoil section
NASA Technical Reports Server (NTRS)
Allison, Dennis O.; Mineck, Raymond E.
1996-01-01
This paper presents aerodynamic characteristics and pressure distributions for an executive-jet modified airfoil and discusses drag reduction relative to a baseline airfoil for two cruise design points. A modified airfoil was tested in the adaptive-wall test section of the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT) for Mach numbers ranging from 0.250 to 0.780 and chord Reynolds numbers ranging from 3.0 x 10(exp 6) to 18.0 x 10(exp 6). The angle of attack was varied from minus 2 degrees to almost 10 degrees. Boundary-layer transition was fixed at 5 percent of chord on both the upper and lower surfaces of the model for most of the test. The two design Mach numbers were 0.654 and 0.735, chord Reynolds numbers were 4.5 x 10(exp 6) and 8.9 x 10(exp 6), and normal-force coefficients were 0.98 and 0.51. Test data are presented graphically as integrated force and moment coefficients and chordwise pressure distributions. The maximum normal-force coefficient decreases with increasing Mach number. At a constant normal-force coefficient in the linear region, as Mach number increases an increase occurs in the slope of normal-force coefficient versus angle of attack, negative pitching-moment coefficient, and drag coefficient. With increasing Reynolds number at a constant normal-force coefficient, the pitching-moment coefficient becomes more negative and the drag coefficient decreases. The pressure distributions reveal that when present, separation begins at the trailing edge as angle of attack is increased. The modified airfoil, which is designed with pitching moment and geometric constraints relative to the baseline airfoil, achieved drag reductions for both design points (12 and 22 counts). The drag reductions are associated with stronger suction pressures in the first 10 percent of the upper surface and weakened shock waves.
Aerodynamics of a hybrid airship
NASA Astrophysics Data System (ADS)
Andan, Amelda Dianne; Asrar, Waqar; Omar, Ashraf A.
2012-06-01
The objective of this paper is to present the results of a numerical study of the aerodynamic parameters of a wingless and a winged-hull airship. The total forces and moment coefficients of the airships have been computed over a range of angles. The results obtained show that addition of a wing to a conventional airship increases the lift has three times the lifting force at positive angle of attack as compared to a wingless airship whereas the drag increases in the range of 19% to 58%. The longitudinal and directional stabilities were found to be statically stable, however, both the conventional airship and the hybrid or winged airships were found to have poor rolling stability. Wingless airship has slightly higher longitudinal stability than a winged airship. The winged airship has better directional stability than the wingless airship. The wingless airship only possesses static rolling stability in the range of yaw angles of -5° to 5°. On the contrary, the winged airship initially tested does not possess rolling stability at all. Computational fluid dynamics (CFD) simulations show that modifications to the wing placement and its dihedral have strong positive effect on the rolling stability. Raising the wings to the center of gravity and introducing a dihedral angle of 5° stabilizes the rolling motion of the winged airship.
A comprehensive plan for helicopter drag reduction
NASA Technical Reports Server (NTRS)
Williams, R. M.; Montana, P. S.
1975-01-01
Current helicopters have parasite drag levels 6 to 10 times as great as fixed wing aircraft. The commensurate poor cruise efficiency results in a substantial degradation of potential mission capability. The paper traces the origins of helicopter drag and shows that the problem (primarily due to bluff body flow separation) can be solved by the adoption of a comprehensive research and development plan. This plan, known as the Fuselage Design Methodology, comprises both nonaerodynamic and aerodynamic aspects. The aerodynamics are discussed in detail and experimental and analytical programs are described which will lead to a solution of the bluff body problem. Some recent results of work conducted at the Naval Ship Research and Development Center (NSRDC) are presented to illustrate these programs. It is concluded that a 75-per cent reduction of helicopter drag is possible by the full implementation of the Fuselage Design Methodology.
Drag calculations of wings using Euler methods
NASA Technical Reports Server (NTRS)
Van Dam, C. P.; Chang, I. C.; Vijgen, P. M. H. W.; Nikfetrat, Koorosh
1991-01-01
Several techniques for the calculation of drag using Euler-equation formulations are discussed and compared. Surface-pressure integration (a nearfield technique) as well as two different farfield calculation techniques are described and applied to three-dimensional flow-field solutions for an aspect-ratio-7 wing with attached flow. The present calculations are limited to steady, low-Mach-number flows around three-dimensional configurations in the absence of active systems such as surface blowing/suction and propulsion. Although the main focus of the paper is the calculation of aerodynamic drag, the calculation of aerodynamic lift is also briefly discussed. Three Euler methods are used to obtain the flowfield solutions. The farfield technique based on the evaluation of a wake-integral appears to provide the most consistent and accurate drag predictions.
Drag reduction obtained by modifying a standard truck
NASA Technical Reports Server (NTRS)
Sheridan, A. E.; Grier, S. J.
1978-01-01
A standard two-axle truck with a box-shaped cargo compartment was tested to determine whether significant reductions in aerodynamic drag could be obtained by modifying the front of the cargo compartment. The coastdown method was used to determine the total drag of the baseline vehicle, which had a square-cornered cargo box, and of several modified configurations. Test velocities ranged from 56.3 to 94.6 kilometers per hour (35 to 60 miles per hour). At 88.5 kilometers per hour (55 miles per hour), the aerodynamic drag reductions obtained with the modified configurations ranged from 8 to 30 percent.
NASA Technical Reports Server (NTRS)
Goodrich, Kenneth H.; Sliwa, Steven M.; Lallman, Frederick J.
1989-01-01
Airplane designs are currently being proposed with a multitude of lifting and control devices. Because of the redundancy in ways to generate moments and forces, there are a variety of strategies for trimming each airplane. A linear optimum trim solution (LOTS) is derived using a Lagrange formulation. LOTS enables the rapid calculation of the longitudinal load distribution resulting in the minimum trim drag in level, steady-state flight for airplanes with a mixture of three or more aerodynamic surfaces and propulsive control effectors. Comparisons of the trim drags obtained using LOTS, a direct constrained optimization method, and several ad hoc methods are presented for vortex-lattice representations of a three-surface airplane and two-surface airplane with thrust vectoring. These comparisons show that LOTS accurately predicts the results obtained from the nonlinear optimization and that the optimum methods result in trim drag reductions of up to 80 percent compared to the ad hoc methods.
NASA Technical Reports Server (NTRS)
Cicolani, Luigi; Kanning, Gerd
1987-01-01
A comprehensive static aerodynamic simulation model of the 8 by 8 by 20 ft MILVAN cargo container is determined by combining the wind tunnel data from a 1972 NASA Ames Research Center study taken over the restricted domain (0 is less than or equal to phi is less than or equal to 90 degrees; 0 is less than or equal to alpha is less than or equal to 45 degrees) with extrapolation relations derived from the geometric symmetry of rectangular boxes. It is found that the aerodynamics of any attitude can be defined from the aerodynamics at an equivalent attitude in the restricted domain (0 is less than phi is less than 45 degrees; 0 is less than alpha is less than 90 degrees). However, a similar comprehensive equivalence with the domain spanned by the data is not available; in particular, about two-thirds of the domain with the absolute value of alpha is greater than 45 degrees is unrelated to the data. Nevertheless, as estimate can be defined for this region consistent with the measured or theoretical values along its boundaries and the theoretical equivalence of points within the region. These descrepancies are assumed to be due to measurement errors. Data from independent wind tunnel studies are reviewed; these are less comprehensive than the NASA Ames Research Center but show good to fair agreement with both the theory and the estimate given here.
NASA Technical Reports Server (NTRS)
Keye, Stefan; Togiti, Vamish; Eisfeld, Bernhard; Brodersen, Olaf P.; Rivers, Melissa B.
2013-01-01
The accurate calculation of aerodynamic forces and moments is of significant importance during the design phase of an aircraft. Reynolds-averaged Navier-Stokes (RANS) based Computational Fluid Dynamics (CFD) has been strongly developed over the last two decades regarding robustness, efficiency, and capabilities for aerodynamically complex configurations. Incremental aerodynamic coefficients of different designs can be calculated with an acceptable reliability at the cruise design point of transonic aircraft for non-separated flows. But regarding absolute values as well as increments at off-design significant challenges still exist to compute aerodynamic data and the underlying flow physics with the accuracy required. In addition to drag, pitching moments are difficult to predict because small deviations of the pressure distributions, e.g. due to neglecting wing bending and twisting caused by the aerodynamic loads can result in large discrepancies compared to experimental data. Flow separations that start to develop at off-design conditions, e.g. in corner-flows, at trailing edges, or shock induced, can have a strong impact on the predictions of aerodynamic coefficients too. Based on these challenges faced by the CFD community a working group of the AIAA Applied Aerodynamics Technical Committee initiated in 2001 the CFD Drag Prediction Workshop (DPW) series resulting in five international workshops. The results of the participants and the committee are summarized in more than 120 papers. The latest, fifth workshop took place in June 2012 in conjunction with the 30th AIAA Applied Aerodynamics Conference. The results in this paper will evaluate the influence of static aeroelastic wing deformations onto pressure distributions and overall aerodynamic coefficients based on the NASA finite element structural model and the common grids.
Flight Dynamics of an Aeroshell Using an Attached Inflatable Aerodynamic Decelerator
NASA Technical Reports Server (NTRS)
Cruz, Juan R.; Schoenenberger, Mark; Axdahl, Erik; Wilhite, Alan
2009-01-01
An aeroelastic analysis of the behavior of an entry vehicle utilizing an attached inflatable aerodynamic decelerator during supersonic flight is presented. The analysis consists of a planar, four degree of freedom simulation. The aeroshell and the IAD are assumed to be separate, rigid bodies connected with a spring-damper at an interface point constraining the relative motion of the two bodies. Aerodynamic forces and moments are modeled using modified Newtonian aerodynamics. The analysis includes the contribution of static aerodynamic forces and moments as well as pitch damping. Two cases are considered in the analysis: constant velocity flight and planar free flight. For the constant velocity and free flight cases with neutral pitch damping, configurations with highly-stiff interfaces exhibit statically stable but dynamically unstable aeroshell angle of attack. Moderately stiff interfaces exhibit static and dynamic stability of aeroshell angle of attack due to damping induced by the pitch angle rate lag between the aeroshell and IAD. For the free-flight case, low values of both the interface stiffness and damping cause divergence of the aeroshell angle of attack due to the offset of the IAD drag force with respect to the aeroshell center of mass. The presence of dynamic aerodynamic moments was found to influence the stability characteristics of the vehicle. The effect of gravity on the aeroshell angle of attack stability characteristics was determined to be negligible for the cases investigated.
Uncovering the aerodynamics of the smallest insects using numerical and physical models
NASA Astrophysics Data System (ADS)
Miller, Laura
2011-11-01
A vast body of research has described the complexity of flight in insects ranging from the fruit fly, Drosophila melanogaster, to the hawk moth, Manduca sexta. The smallest flying insects have received far less attention, although previous work has shown that flight kinematics and aerodynamics can be significantly different. In this presentation, three-dimensional direct numerical simulations are used to compute the lift and drag forces generated by flexible wings to reveal the aerodynamics of these tiny fliers. Results are validated against dynamically scaled physical models. At the lowest Reynolds numbers relevant to insect flight, the relative forces required to rotate the wings and fling them apart become substantially greater. Wing flexibility can reduce these forces and improve efficiency in some situations.
Aerodynamics of badminton shuttlecocks
NASA Astrophysics Data System (ADS)
Verma, Aekaansh; Desai, Ajinkya; Mittal, Sanjay
2013-08-01
A computational study is carried out to understand the aerodynamics of shuttlecocks used in the sport of badminton. The speed of the shuttlecock considered is in the range of 25-50 m/s. The relative contribution of various parts of the shuttlecock to the overall drag is studied. It is found that the feathers, and the net in the case of a synthetic shuttlecock, contribute the maximum. The gaps, in the lower section of the skirt, play a major role in entraining the surrounding fluid and causing a difference between the pressure inside and outside the skirt. This pressure difference leads to drag. This is confirmed via computations for a shuttlecock with no gaps. The synthetic shuttle experiences more drag than the feather model. Unlike the synthetic model, the feather shuttlecock is associated with a swirling flow towards the end of the skirt. The effect of the twist angle of the feathers on the drag as well as the flow has also been studied.
NASA Technical Reports Server (NTRS)
Edquist, Karl T.
2006-01-01
Comparisons are made between the LAURA Navier-Stokes code and Viking Lander Capsule hypersonic aerodynamics data from ground and flight measurements. Wind tunnel data are available for a 3.48 percent scale model at Mach 6 and a 2.75 percent scale model at Mach 10.35, both under perfect gas air conditions. Viking Lander 1 aerodynamics flight data also exist from on-board instrumentation for velocities between 2900 and 4400 m/sec (Mach 14 to 23.3). LAURA flowfield solutions are obtained for the geometry as tested or flown, including sting effects at tunnel conditions and finite-rate chemistry effects in flight. Using the flight vehicle center-of-gravity location (trim angle approx. equals -11.1 deg), the computed trim angle at tunnel conditions is within 0.31 degrees of the angle derived from Mach 6 data and 0.13 degrees from the Mach 10.35 trim angle. LAURA Mach 6 trim lift and drag force coefficients are within 2 percent of measured data, and computed trim lift-to-drag ratio is within 4 percent of the data. Computed trim lift and drag force coefficients at Mach 10.35 are within 5 percent and 3 percent, respectively, of wind tunnel data. Computed trim lift-to-drag ratio is within 2 percent of the Mach 10.35 data. Using the nominal density profile and center-of-gravity location, LAURA trim angle at flight conditions is within 0.5 degrees of the total angle measured from on-board instrumentation. LAURA trim lift and drag force coefficients at flight conditions are within 7 and 5 percent, respectively, of the flight data. Computed trim lift-to-drag ratio is within 4 percent of the data. Computed aerodynamics sensitivities to center-of-gravity location, atmospheric density, and grid refinement are generally small. The results will enable a better estimate of aerodynamics uncertainties for future Mars entry vehicles where non-zero angle-of-attack is required.
An investigation into using differential drag for controlling a formation of CubeSats
NASA Astrophysics Data System (ADS)
Horsley, M.
2011-09-01
As the SSA system upgrades its existing capabilities and adds new ones, the potential offered by inexpensive CubeSat-based systems is growing more attractive. The potential benefits of using CubeSats increase if they are operated in groups to form ‘virtual’ satellites, which have the same functionality of a much larger satellite, but at a fraction of the cost. This paper will investigate the feasibility of using differential aerodynamic forces to control a formation of CubeSats in order to form a virtual satellite. Unfortunately, due to third body gravitational forces, solar radiation pressure, and other perturbing forces, the satellites will drift apart if no control mechanism is employed to maintain the formation. However, providing for a control mechanism is difficult. Using a rocket engine is expensive, increases mission risk, and requires fuel to be carried in the rather limited volume available in a typical CubeSat. However, passive techniques that take advantage of the differential aerodynamic forces experienced by two spacecraft can be used to exert a modest amount of control over the formation. Techniques for doing this have been discussed in the literature. These techniques rely on a simple drag plate, and only allow modest control of the formation in the plane defined by the spacecrafts orbit. An alternative is to treat the drag plate as an aerodynamic control surface, much as is done with an aircraft. This technique allows the control surface to be oriented in a fully 3 dimensional fashion, allowing a greater range of control of the satellite formation. A challenge in treating the drag plate as a 3 dimensional control surface is that the equations of motion describing the relative motions of the satellites become fully coupled with their relative orientations. Thus, controlling the satellite formation by adjusting the relative orientations of the different satellites will require solving a fully coupled set of differential equations and devising a
Experimental Investigation on Aerodynamic Control of a Wing with Distributed Plasma Actuators
NASA Astrophysics Data System (ADS)
Han, Menghu; Li, Jun; Liang, Hua; Niu, Zhongguo; Zhao, Guangyin
2015-06-01
Experimental investigation of active flow control on the aerodynamic performance of a flying wing is conducted. Subsonic wind tunnel tests are performed using a model of a 35° swept flying wing with an nanosecond dielectric barrier discharge (NS-DBD) plasma actuator, which is installed symmetrically on the wing leading edge. The lift and drag coefficient, lift-to-drag ratio and pitching moment coefficient are tested by a six-component force balance for a range of angles of attack. The results indicate that a 44.5% increase in the lift coefficient, a 34.2% decrease in the drag coefficient and a 22.4% increase in the maximum lift-to-drag ratio can be achieved as compared with the baseline case. The effects of several actuation parameters are also investigated, and the results show that control efficiency demonstrates a strong dependence on actuation location and frequency. Furthermore, we highlight the use of distributed plasma actuators at the leading edge to enhance the aerodynamic performance, giving insight into the different mechanism of separation control and vortex control, which shows tremendous potential in practical flow control for a broad range of angles of attack. supported by National Natural Science Foundation of China (Nos. 51276197, 51207169 and 51336011)
Computation of Flow Over a Drag Prediction Workshop Wing/Body Transport Configuration Using CFL3D
NASA Technical Reports Server (NTRS)
Rumsey, Christopher L.; Biedron, Robert T.
2001-01-01
A Drag Prediction Workshop was held in conjunction with the 19th AIAA Applied Aerodynamics Conference in June 2001. The purpose of the workshop was to assess the prediction of drag by computational methods for a wing/body configuration (DLR-F4) representative of subsonic transport aircraft. This report details computed results submitted to this workshop using the Reynolds-averaged Navier-Stokes code CFL3D. Two supplied grids were used: a point-matched 1-to-1 multi-block grid, and an overset multi-block grid. The 1-to-1 grid, generally of much poorer quality and with less streamwise resolution than the overset grid, is found to be too coarse to adequately resolve the surface pressures. However, the global forces and moments are nonetheless similar to those computed using the overset grid. The effect of three different turbulence models is assessed using the 1-to-1 grid. Surface pressures are very similar overall, and the drag variation due to turbulence model is 18 drag counts. Most of this drag variation is in the friction component, and is attributed in part to insufficient grid resolution of the 1-to-1 grid. The misnomer of 'fully turbulent' computations is discussed; comparisons are made using different transition locations and their effects on the global forces and moments are quantified. Finally, the effect of two different versions of a widely used one-equation turbulence model is explored.
Aerodynamics of thrust vectoring
NASA Technical Reports Server (NTRS)
Tseng, J. B.; Lan, C. Edward
1989-01-01
Thrust vectoring as a means to enhance maneuverability and aerodynamic performane of a tactical aircraft is discussed. This concept usually involves the installation of a multifunction nozzle. With the nozzle, the engine thrust can be changed in direction without changing the attitude of the aircraft. Change in the direction of thrust induces a significant change in the aerodynamic forces on the aircraft. Therefore, this device can be used for lift-augmenting as well as stability and control purposes. When the thrust is deflected in the longitudinal direction, the lift force and the pitching stability can be manipulated, while the yawing stability can be controlled by directing the thrust in the lateral direction.
NASA Technical Reports Server (NTRS)
Roskam, J.; Lan, C.; Mehrotra, S.
1972-01-01
The computer program used to determine the rigid and elastic stability derivatives presented in the summary report is listed in this appendix along with instructions for its use, sample input data and answers. This program represents the airplane at subsonic and supersonic speeds as (a) thin surface(s) (without dihedral) composed of discrete panels of constant pressure according to the method of Woodward for the aerodynamic effects and slender beam(s) for the structural effects. Given a set of input data, the computer program calculates an aerodynamic influence coefficient matrix and a structural influence coefficient matrix.
Pepper, W.B.
1984-05-09
A rotating parachute for decelerating objects travelling through atmosphere at subsonic or supersonic deployment speeds includes a circular canopy having a plurality of circumferentially arranged flexible panels projecting radially from a solid central disk. A slot extends radially between adjacent panels to the outer periphery of the canopy. Upon deployment, the solid disk diverts air radially to rapidly inflate the panels into a position of maximum diameter. Air impinging on the panels adjacent the panel slots rotates the parachute during its descent. Centrifugal force flattens the canopy into a constant maximum diameter during terminal descent for maximum drag and deceleration.
NASA Technical Reports Server (NTRS)
Gelzer, Christian
2011-01-01
In 1973 engineers at Dryden began investigating ways to reduce aerodynamic drag on land vehicles. They began with a delivery van whose shape they changed dramatically, finally reducing its aerodynamic drag by more than 5 percent. They then turned their attention to tracator-trailers, modifying a cab-over and reducing its aerodynamic drag by nearly 25 percent. Further research identified additional areas worth attention, but in the intervening decades few of those changes have appeared.
Computational analysis of methods for reduction of induced drag
NASA Technical Reports Server (NTRS)
Janus, J. M.; Chatterjee, Animesh; Cave, Chris
1993-01-01
The purpose of this effort was to perform a computational flow analysis of a design concept centered around induced drag reduction and tip-vortex energy recovery. The flow model solves the unsteady three-dimensional Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. The numerical scheme is an approximately-factored block LU implicit Newton iterative-refinement method. Multiblock domain decomposition is used to partition the field into an ordered arrangement of blocks. Three configurations are analyzed: a baseline fuselage-wing, a fuselage-wing-nacelle, and a fuselage-wing-nacelle-propfan. Aerodynamic force coefficients, propfan performance coefficients, and flowfield maps are used to qualitatively access design efficacy. Where appropriate, comparisons are made with available experimental data.
F-16XL ship #1 landing with drag chute
NASA Technical Reports Server (NTRS)
1995-01-01
NASA's single-seat F-16XL makes a drag chute landing on the runway at Edwards Air Force Base in California's Mojave Desert. The aircraft was most recently used in the Cranked-Arrow Wing Aerodynamics Project (CAWAP) to test boundary layer pressures and distribution. Previously it had been used in a program to investigate the characteristics of sonic booms for NASA's High Speed Research Program. Data from the program will be used in the development of a high speed civilian transport. During the series of sonic boom research flights, the F-16XL was used to probe the shock waves being generated by a NASA SR-71 and record their shape and intensity.
Aerodynamic analysis of natural flapping flight using a lift model based on spanwise flow
NASA Astrophysics Data System (ADS)
Alford, Lionel D., Jr.
This study successfully described the mechanics of flapping hovering flight within the framework of conventional aerodynamics. Additionally, the theory proposed and supported by this research provides an entirely new way of looking at animal flapping flight. The mechanisms of biological flight are not well understood, and researchers have not been able to describe them using conventional aerodynamic forces. This study proposed that natural flapping flight can be broken down into a simplest model, that this model can then be used to develop a mathematical representation of flapping hovering flight, and finally, that the model can be successfully refined and compared to biological flapping data. This paper proposed a unique theory that the lift of a flapping animal is primarily the result of velocity across the cambered span of the wing. A force analysis was developed using centripetal acceleration to define an acceleration profile that would lead to a spanwise velocity profile. The force produced by the spanwise velocity profile was determined using a computational fluid dynamics analysis of flow on the simplified wing model. The overall forces on the model were found to produce more than twice the lift required for hovering flight. In addition, spanwise lift was shown to generate induced drag on the wing. Induced drag increased both the model wing's lift and drag. The model allowed the development of a mathematical representation that could be refined to account for insect hovering characteristics and that could predict expected physical attributes of the fluid flow. This computational representation resulted in a profile of lift and drag production that corresponds to known force profiles for insect flight. The model of flapping flight was shown to produce results similar to biological observation and experiment, and these results can potentially be applied to the study of other flapping animals. This work provides a foundation on which to base further exploration
Aerodynamics of a Party Balloon
ERIC Educational Resources Information Center
Cross, Rod
2007-01-01
It is well-known that a party balloon can be made to fly erratically across a room, but it can also be used for quantitative measurements of other aspects of aerodynamics. Since a balloon is light and has a large surface area, even relatively weak aerodynamic forces can be readily demonstrated or measured in the classroom. Accurate measurements…
Lift, Drag, and Elevator Hinge Moments of Handley Page Control Surfaces
NASA Technical Reports Server (NTRS)
Smith, R H
1928-01-01
This report combines the wind tunnel results of tests on four control surface models made in the two wind tunnels of the Navy Aerodynamic Laboratory, Washington Navy Yard, during the years of 1922 and 1924, and submitted for publication to the National Advisory Committee for Aeronautics May 7, 1927. The purpose of the tests was to compare, first, the lifts and the aerodynamic efficiencies of the control surfaces from which their relative effectiveness as tail planes could be determined; then the elevator hinge moments upon which their relative ease of operation depended. The lift and drag forces on the control surface models were obtained for various stabilizer angles and elevator settings in the 8 by 8 foot tunnel by the writer in 1922; the corresponding hinge moments were found in the 4 by 4 foot tunnel by Mr. R. M. Bear in 1924. (author)
External aerodynamics of heavy ground vehicles: Computations and wind tunnel testing
NASA Astrophysics Data System (ADS)
Bayraktar, Ilhan
Aerodynamic characteristics of a ground vehicle affect vehicle operation in many ways. Aerodynamic drag, lift and side forces have influence on fuel efficiency, vehicle top speed and acceleration performance. In addition, engine cooling, air conditioning, wind noise, visibility, stability and crosswind sensitivity are some other tasks for vehicle aerodynamics. All of these areas benefit from drag reduction and changing the lift force in favor of the operating conditions. This can be achieved by optimization of external body geometry and flow modification devices. Considering the latter, a thorough understanding of the airflow is a prerequisite. The present study aims to simulate the external flow field around a ground vehicle using a computational method. The model and the method are selected to be three dimensional and time-dependent. The Reynolds-averaged Navier Stokes equations are solved using a finite volume method. The Renormalization Group (RNG) k-epsilon model was elected for closure of the turbulent quantities. Initially, the aerodynamics of a generic bluff body is studied computationally and experimentally to demonstrate a number of relevant issues including the validation of the computational method. Experimental study was conducted at the Langley Full Scale Wind Tunnel using pressure probes and force measurement equipment. Experiments and computations are conducted on several geometric configurations. Results are compared in an attempt to validate the computational model for ground vehicle aerodynamics. Then, the external aerodynamics of a heavy truck is simulated using the validated computational fluid dynamics method, and the external flow is presented using computer visualization. Finally, to help the estimation of the error due to two commonly practiced engineering simplifications, a parametric study on the tires and the moving ground effect are conducted on full-scale tractor-trailer configuration. Force and pressure coefficients and velocity
Drag reduction of a hairy disk
NASA Astrophysics Data System (ADS)
Niu, Jun; Hu, David L.
2011-10-01
We investigate experimentally the hydrodynamics of a hairy disk immersed in a two-dimensional flowing soap film. Drag force is measured as a function of hair length, density, and coating area. An optimum combination of these parameters yields a drag reduction of 17%, which confirms previous numerical predictions (15%). Flow visualization indicates the primary mechanism for drag reduction is the bending, adhesion, and reinforcement of hairs trailing the disk, which reduces wake width and traps "dead water." Thus, the use of hairy coatings can substantially reduce an object's drag while negligibly increasing its weight.
Dragging a floating horizontal cylinder
NASA Astrophysics Data System (ADS)
Lee, Duck-Gyu; Kim, Ho-Young
2010-11-01
A cylinder immersed in a fluid stream experiences a drag, and it is well known that the drag coefficient is a function of the Reynolds number only. Here we study the force exerted on a long horizontal cylinder that is dragged perpendicular to its axis while floating on an air-water interface with a high Reynolds number. In addition to the flow-induced drag, the floating body is subjected to capillary forces along the contact line where the three phases of liquid/solid/gas meet. We first theoretically predict the meniscus profile around the horizontally moving cylinder assuming the potential flow, and show that the profile is in good agreement with that obtained experimentally. Then we compare our theoretical predictions and experimental measurement results for the drag coefficient of a floating horizontal cylinder that is given by a function of the Weber number and the Bond number. This study can help us to understand the horizontal motion of partially submerged objects at air-liquid interface, such as semi-aquatic insects and marine plants.
Viking entry aerodynamics and heating
NASA Technical Reports Server (NTRS)
Polutchko, R. J.
1974-01-01
The characteristics of the Mars entry including the mission sequence of events and associated spacecraft weights are described along with the Viking spacecraft. Test data are presented for the aerodynamic characteristics of the entry vehicle showing trimmed alpha, drag coefficient, and trimmed lift to drag ratio versus Mach number; the damping characteristics of the entry configuration; the angle of attack time history of Viking entries; stagnation heating and pressure time histories; and the aeroshell heating distribution as obtained in tests run in a shock tunnel for various gases. Flight tests which demonstrate the aerodynamic separation of the full-scale aeroshell and the flying qualities of the entry configuration in an uncontrolled mode are documented. Design values selected for the heat protection system based on the test data and analysis performed are presented.
Robert J. Englar
2001-05-14
Research is being conducted at the Georgia Tech Research Institute (GTRI) to develop advanced aerodynamic devices to improve the performance, economics, stability, handling and safety of operation of Heavy Vehicles by using previously-developed and flight-tested pneumatic (blown) aircraft technology. Recent wind-tunnel investigations of a generic Heavy Vehicle model with blowing slots on both the leading and trailing edges of the trailer have been conducted under contract to the DOE Office of Heavy Vehicle Technologies. These experimental results show overall aerodynamic drag reductions on the Pneumatic Heavy Vehicle of 50% using only 1 psig blowing pressure in the plenums, and over 80% drag reductions if additional blowing air were available. Additionally, an increase in drag force for braking was confirmed by blowing different slots. Lift coefficient was increased for rolling resistance reduction by blowing only the top slot, while downforce was produced for traction increase by blowing only the bottom. Also, side force and yawing moment were generated on either side of the vehicle, and directional stability was restored by blowing the appropriate side slot. These experimental results and the predicted full-scale payoffs are presented in this paper, as is a discussion of additional applications to conventional commercial autos, buses, motor homes, and Sport Utility Vehicles.
NASA Technical Reports Server (NTRS)
Conrad, George R.; Robbins, Edward J.
1991-01-01
The evolution of an empirical drag relationship that has stimulated rethinking regarding the physics of balloon drag phenomena is discussed. Combined parasitic drag from all sources in the balloon system are estimated to constitute less than 10 percent of the total system drag. It is shown that the difference between flight-determined drag coefficients and those based on the spherical assumption should be related to the square of the Froude number.
Aerodynamics in the classroom and at the ball park
NASA Astrophysics Data System (ADS)
Cross, Rod
2012-04-01
Experiments suitable for classroom projects or demonstrations are described concerning the aerodynamics of polystyrene balls. A light ball with sufficient backspin can curve vertically upward through the air, defying gravity and providing a dramatic visual demonstration of the Magnus effect. A ball projected with backspin can also curve downward with a vertical acceleration greater than that due to gravity if the Magnus force is negative. These effects were investigated by filming the flight of balls projected in an approximately horizontal direction so that the lift and drag forces could be easily measured. The balls were also fitted with artificial raised seams and projected with backspin toward a vertical target in order to measure the sideways deflection over a known horizontal distance. It was found that (a) a ball with a seam on one side can deflect either left or right depending on its launch speed and (b) a ball with a baseball seam can also deflect sideways even when there is no sideways component of the drag or lift forces acting on the ball. Depending on the orientations of the seam and the spin axis, a sideways force on a baseball can arise either if there is rough patch on one side of the ball or if there is a smooth patch. A scuff ball with a rough patch on one side is illegal in baseball. The effect of a smooth patch is a surprising new observation.
Quantifying the Effect of Pressure Sensitive Paint On Aerodynamic Data
NASA Technical Reports Server (NTRS)
Amer, T. R.; Obara, C. J.; Liu, T.
2003-01-01
A thin pressure sensitive paint (PSP) coating can slightly modify the overall shape of a wind-tunnel model and produce surface roughness or smoothness that does not exist on the unpainted model. These undesirable changes in model geometry may alter flow over the model, and affect the pressure distribution and aerodynamic forces and moments on the model. This study quantifies the effects of PSP on three models in low-speed, transonic and supersonic flow regimes. At a 95% confidence level, the PSP effects on the integrated forces are insignificant for a slender arrow-wing-fuselage model and delta wing model with two different paints at Mach 0.2, 1.8, and 2.16 relative to the total balance accuracy limit. The data displayed a repeatability of 2.5 drag counts, while the balance accuracy limit was about 5.5 drag counts. At transonic speeds, the paint has a localized effect at high angles of attack and has a resolvable effect on the normal force, which is significant relative to the balance accuracy limit. For low speeds, the PSP coating has a localized effect on the pressure tap measurements, which leads to an appreciable decrease in the pressure tap reading. Moreover, the force and moment measurements had a poor precision, which precluded the ability to measure the PSP effect for this particular test.
Biomimetic spiroid winglets for lift and drag control
NASA Astrophysics Data System (ADS)
Guerrero, Joel E.; Maestro, Dario; Bottaro, Alessandro
2012-01-01
In aeronautical engineering, drag reduction constitutes a challenge and there is room for improvement and innovative developments. The drag breakdown of a typical transport aircraft shows that the lift-induced drag can amount to as much as 40% of the total drag at cruise conditions and 80-90% of the total drag in take-off configuration. One way of reducing lift-induced drag is by using wingtip devices. By applying biomimetic abstraction of the principle behind a bird's wingtip feathers, we study spiroid wingtips, which look like an extended blended wingtip that bends upward by 360 degrees to form a large rigid ribbon. The numerical investigation of such a wingtip device is described and preliminary indications of its aerodynamic performance are provided.
Analysis of Asymmetric Aircraft Aerodynamics Due to an Experimental Wing Glove
NASA Technical Reports Server (NTRS)
Hartshorn, Fletcher
2011-01-01
Aerodynamic computational fluid dynamics analysis of a wing glove attached to one wing of a business jet is presented and discussed. A wing glove placed on only one wing will produce asymmetric aerodynamic effects that will result in overall changes in the forces and moments acting on the aircraft. These changes, referred to as deltas, need to be determined and quantified to ensure that the wing glove does not have a significant effect on the aircraft flight characteristics. TRANAIR (Calmar Research Corporation, Cato, New York), a nonlinear full potential solver, and Star-CCM+ (CD-adapco, Melville, New York), a finite volume full Reynolds-averaged Navier-Stokes computational fluid dynamics solver, are used to analyze a full aircraft with and without the glove at a variety of flight conditions, aircraft configurations, and angles of attack and sideslip. Changes in the aircraft lift, drag, and side force along with roll, pitch, and yaw are presented. Span lift and moment distributions are also presented for a more detailed look at the effects of the glove on the aircraft. Aerodynamic flow phenomena due to the addition of the glove are discussed. Results show that the glove produces only small changes in the aerodynamic forces and moments acting on the aircraft, most of which are insignificant.
Assessment of aerodynamic performance of V/STOL and STOVL fighter aircraft
NASA Technical Reports Server (NTRS)
Nelms, W. P.
1984-01-01
The aerodynamic performance of V/STOL and STOVL fighter/attack aircraft was assessed. Aerodynamic and propulsion/airframe integration activities are described and small-and large-scale research programs are considered. Uncertainties affecting aerodynamic performance that are associated with special configuration features resulting from the V/STOL requirement are addressed. Example uncertainties related to minimum drag, wave drag, high angle of attack characteristics, and power-induced effects. Engine design configurations from several aircraft manufacturers are reviewed.
Assessment of aerodynamic performance of V/STOL and STOVL fighter aircraft
NASA Technical Reports Server (NTRS)
Nelms, W. P.
1984-01-01
The aerodynamic performance of V/STOL and STOVL fighter/attack aircraft was assessed. Aerodynamic and propulsion/airframe integration activities are described and small and large scale research programs are considered. Uncertainties affecting aerodynamic performance that are associated with special configuration features resulting from the V/STOL requirement are addressed. Example uncertainties relate to minimum drag, wave drag, high angle of attack characteristics, and power induced effects.
Hamiltonian approach to frame dragging
NASA Astrophysics Data System (ADS)
Epstein, Kenneth J.
2008-07-01
A Hamiltonian approach makes the phenomenon of frame dragging apparent “up front” from the appearance of the drag velocity in the Hamiltonian of a test particle in an arbitrary metric. Hamiltonian (1) uses the inhomogeneous force equation (4), which applies to non-geodesic motion as well as to geodesics. The Hamiltonian is not in manifestly covariant form, but is covariant because it is derived from Hamilton’s manifestly covariant scalar action principle. A distinction is made between manifest frame dragging such as that in the Kerr metric, and hidden frame dragging that can be made manifest by a coordinate transformation such as that applied to the Robertson-Walker metric in Sect. 2. In Sect. 3 a zone of repulsive gravity is found in the extreme Kerr metric. Section 4 treats frame dragging in special relativity as a manifestation of the equivalence principle in accelerated frames. It answers a question posed by Bell about how the Lorentz contraction can break a thread connecting two uniformly accelerated rocket ships. In Sect. 5 the form of the Hamiltonian facilitates the definition of gravitomagnetic and gravitoelectric potentials.
NASA Technical Reports Server (NTRS)
Bamber, M J; Zimmerman, C H
1935-01-01
The aerodynamic forces and moments on a 1/12-scale model of the F4B-2 airplane were measured with the spinning balance in nine spinning attitudes with three sets of tail surfaces, namely, F4B-2 surfaces; F4B-4 fin and rudder with rectangular stabilizer; and with all tail surfaces removed. In one of these attitudes measurements were made to determine the effect upon the forces and moments of independent and of simultaneous displacement of the rudder and elevator for two of the sets of tail surfaces. Additional measurements were made for a comparison of model and full-scale data for six attitudes that were determined from flight tests with various control settings. The characteristics were found to vary in the usual manner with angle of attack and sideslip. The F4B-2 surfaces were quite ineffective as a source of yawing moments. The F4B-4 fin and F4B-2 stabilizer gave a greater damping yawing moment when controls were against the spin than did the F4B-2 surfaces but otherwise there was little difference. Substitution of a rectangular stabilizer for the F4B-2 stabilizer made no appreciable difference in the coefficient. Further comparisons with other airplane types are necessary before final conclusions can be drawn as to the relations between model and full-scale spin measurements.
X-31 Landing with Drag Chute Deploy
NASA Technical Reports Server (NTRS)
1995-01-01
One of two X-31 Enhanced Fighter Maneuverability Demonstrator aircraft, flown by an international test organization at NASA's Dryden Flight Research Center, Edwards, California, deploys its drag chute upon landing after a research flight. The aircraft obtained data that may apply to the design and development of highly-maneuverable flights of the future. The X-31 had a three-axis thrust-vectoring system, coupled with advanced flight controls, to allow it to maneuver tightly at very high angles of attack. The X-31 Enhanced Fighter Maneuverability (EFM) demonstrator flew at the Ames- Dryden Flight Research Facility, Edwards, California (redesignated the Dryden Flight Research Center in 1994) from February 1992 until 1995 and before that at the Air Force's Plant 42 in Palmdale, California. The goal of the project was to provide design information for the next generation of highly maneuverable fighter aircraft. This program demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with an advanced flight control system to provide controlled flight to very high angles of attack. The result was a significant advantage over most conventional fighters in close-in combat situations. The X-31 flight program focused on agile flight within the post-stall regime, producing technical data to give aircraft designers a better understanding of aerodynamics, effectiveness of flight controls and thrust vectoring, and airflow phenomena at high angles of attack. Stall is a condition of an airplane or an airfoil in which lift decreases and drag increases due to the separation of airflow. Thrust vectoring compensates for the loss of control through normal aerodynamic surfaces that occurs during a stall. Post-stall refers to flying beyond the normal stall angle of attack, which in the X-31 was at a 30-degree angle of attack. During Dryden flight testing, the X-31 aircraft established several milestones. On November 6, 1992, the X-31 achieved controlled
NASA Technical Reports Server (NTRS)
Miller, Eric J.; Cruz, Josue; Lung, Shun-Fat; Kota, Sridhar; Ervin, Gregory; Lu, Kerr-Jia; Flick, Pete
2016-01-01
A seamless adaptive compliant trailing edge (ACTE) flap was demonstrated in flight on a Gulfstream III aircraft at the NASA Armstrong Flight Research Center. The trailing edge flap was deflected between minus 2 deg up and plus 30 deg down in flight. The safety-of-flight parameters for the ACTE flap experiment require that flap-to-wing interface loads be sensed and monitored in real time to ensure that the structural load limits of the wing are not exceeded. The attachment fittings connecting the flap to the aircraft wing rear spar were instrumented with strain gages and calibrated using known loads for measuring hinge moment and normal force loads in flight. The safety-of-flight parameters for the ACTE flap experiment require that flap-to-wing interface loads be sensed and monitored in real time to ensure that the structural load limits of the wing are not exceeded. The attachment fittings connecting the flap to the aircraft wing rear spar were instrumented with strain gages and calibrated using known loads for measuring hinge moment and normal force loads in flight. The interface hardware instrumentation layout and load calibration are discussed. Twenty-one applied calibration test load cases were developed for each individual fitting. The 2-sigma residual errors for the hinge moment was calculated to be 2.4 percent, and for normal force was calculated to be 7.3 percent. The hinge moment and normal force generated by the ACTE flap with a hinge point located at 26-percent wing chord were measured during steady state and symmetric pitch maneuvers. The loads predicted from analysis were compared to the loads observed in flight. The hinge moment loads showed good agreement with the flight loads while the normal force loads calculated from analysis were over-predicted by approximately 20 percent. Normal force and hinge moment loads calculated from the pressure sensors located on the ACTE showed good agreement with the loads calculated from the installed strain gages.
Eder, Heinrich; Fiedler, Wolfgang; Pascoe, Xaver
2011-01-01
Primary feathers of soaring land birds have evolved into highly specialized flight feathers characterized by morphological improvements affecting aerodynamic performance. The foremost feathers in the cascade have to bear high lift-loading with a strong bending during soaring flight. A challenge to the study of feather aerodynamics is to understand how the observed low drag and high lift values in the Reynolds (Re) regime from 1.0 to 2.0E4 can be achieved. Computed micro-tomography images show that the feather responds to high lift-loading with an increasing nose-droop and profile-camber. Wind-tunnel tests conducted with the foremost primary feather of a White Stork (Ciconia ciconia) at Re = 1.8E4 indicated a surprisingly high maximum lift coefficient of 1.5 and a glide ratio of nearly 10. We present evidence that this is due to morphologic characteristics formed by the cristae dorsales as well as air-permeable arrays along the rhachis. Measurements of lift and drag forces with open and closed pores confirmed the efficiency of this mechanism. Porous structures facilitate a blow out, comparable to technical blow-hole turbulators for sailplanes and low speed turbine-blades. From our findings, we conclude that the mechanism has evolved in order to affect the boundary layer and to reduce aerodynamic drag of the feather. PMID:20938776
NASA Astrophysics Data System (ADS)
Bushnell, D. M.; Moore, K. J.
Recent studies on the drag-reducing shapes, structures, and behaviors of swimming and flying animals are reviewed, with an emphasis on potential analogs in vehicle design. Consideration is given to form drag reduction (turbulent flow, vortex generation, mass transfer, and adaptations for body-intersection regions), skin-friction drag reduction (polymers, surfactants, and bubbles as surface 'additives'), reduction of the drag due to lift, drag-reduction studies on porpoises, and drag-reducing animal behavior (e.g., leaping out of the water by porpoises). The need for further research is stressed.
Hood, Michael
1986-01-01
A mounting movable with respect to an adjacent hard face has a projecting drag bit adapted to engage the hard face. The drag bit is disposed for movement relative to the mounting by encounter of the drag bit with the hard face. That relative movement regulates a valve in a water passageway, preferably extending through the drag bit, to play a stream of water in the area of contact of the drag bit and the hard face and to prevent such water play when the drag bit is out of contact with the hard face.
Hood, M.
1986-02-11
A mounting movable with respect to an adjacent hard face has a projecting drag bit adapted to engage the hard face. The drag bit is disposed for movement relative to the mounting by encounter of the drag bit with the hard face. That relative movement regulates a valve in a water passageway, preferably extending through the drag bit, to play a stream of water in the area of contact of the drag bit and the hard face and to prevent such water play when the drag bit is out of contact with the hard face. 4 figs.
NASA Technical Reports Server (NTRS)
Bushnell, D. M.; Moore, K. J.
1991-01-01
Recent studies on the drag-reducing shapes, structures, and behaviors of swimming and flying animals are reviewed, with an emphasis on potential analogs in vehicle design. Consideration is given to form drag reduction (turbulent flow, vortex generation, mass transfer, and adaptations for body-intersection regions), skin-friction drag reduction (polymers, surfactants, and bubbles as surface 'additives'), reduction of the drag due to lift, drag-reduction studies on porpoises, and drag-reducing animal behavior (e.g., leaping out of the water by porpoises). The need for further research is stressed.
Drag reduction of a heavy vehicle
NASA Astrophysics Data System (ADS)
Ortega, Jason; Salari, Kambiz
2007-11-01
During the 1970's and 1980's, a number of first-generation drag reduction devices were designed to reduce the aerodynamic losses of heavy vehicles (Cooper, 2003). The result of this effort led to the development of a number of devices that improved the aerodynamics of a heavy vehicle tractor. Additionally, a number of second-generation devices were developed for heavy vehicle trailers. Unfortunately, these trailer devices did not enter into the market on a wide-scale basis and, as a result, the modern heavy vehicle trailer largely remains a ``box on wheels'' with minimal aerodynamic consideration taken into its design. The primary obstacle to implementing trailer devices was not their effectiveness in reducing drag, but rather operational, maintenance, and ultimately, economic concerns. However, with rising fuel costs and potentially unstable fuel supplies, there is a renewed objective to further reduce heavy vehicle fuel usage. To accomplish this purpose, the present study investigates the drag reduction capability of a trailer device, which neither reduces the trailer cargo capacity, nor limits access to the trailer doors. RANS simulations are performed on a full-scale tractor-trailer that is traveling at highway conditions with and without the trailer device. This work was performed under the auspices of the U.S. Department of Energy by the University of California, Lawrence Livermore National Laboratory under Contract No. W-7405-Eng-48.
NASA Technical Reports Server (NTRS)
Baize, Daniel G. (Editor)
1999-01-01
The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Aerodynamic Performance Workshop on February 25-28, 1997. The workshop was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in areas of Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization), High-Lift, Flight Controls, Supersonic Laminar Flow Control, and Sonic Boom Prediction. The workshop objectives were to (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientist and engineers working HSCT aerodynamics. In particular, single- and multi-point optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT Motion Simulator results were presented along with executive summaries for all the Aerodynamic Performance technology areas.
High speed aerodynamics of upper surface blowing aircraft configurations
NASA Technical Reports Server (NTRS)
Birckelbaw, Larry D.
1992-01-01
An experimental investigation of the high speed aerodynamics of Upper Surface Blowing (USB) aircraft configurations has been conducted to accurately define the magnitude and causes of the powered configuration cruise drag. A highly instrumented wind tunnel model of a realistic USB configuration was used which permitted parametric variations in the number and spanwise location of the nacelles and was powered with two turbofan engine simulators. The tests conducted in the Ames 14 Foot Transonic Wind Tunnel examined 10 different configurations at Mach numbers from 0.5 to 0.775, fan nozzle pressure ratios from 1.1 to 2.1 and angles of attack from -4 to 6 degrees. Measured force data is presented which indicates the cruise drag penalty associated with each configuration and surface pressure contour plots are used to illustrate the underlying flowfield physics. It was found that all of the tested configurations suffered from a severe drag penalty which increased with freestream Mach number, power setting and angle of attack and was associated with the presence of strong shocks and regions of separated flow in the wing/nacelle junction regions.
Experiments examining drag in linear droplet packets
NASA Astrophysics Data System (ADS)
Nguyen, Q. V.; Dunn-Rankin, D.
1992-01-01
This paper presents an experimental study of vertically traveling droplet packets, where the droplets in each packet are aligned linearly, one behind another. The paper describes in detail, an experimental apparatus that produces repeatable, linearly aligned, and isolated droplet packets containing 1 6 droplets per packet. The apparatus is suitable for examining aerodynamic interactions between droplets within each packet. This paper demonstrates the performance of the apparatus by examining the drag reduction and collision of droplets traveling in the wake of a lead droplet. Comparison of a calculated single droplet trajectory with the detailed droplet position versus time data for a droplet packet provides the average drag reduction experienced by the trailing droplets due to the aerodynamic wake of the lead droplet. For the conditions of our experiment (4 droplet packet, 145 μm methanol droplets, 10 m/s initial velocity, initial droplet spacing of 5.2 droplet diameters, Reynolds number approx. 80) the average drag on the first trailing droplet was found to be 75% of the drag on the lead droplet.
2015-01-01
Tragopogon pratensis is a small herbaceous plant that uses wind as the dispersal vector for its seeds. The seeds are attached to parachutes that increase the aerodynamic drag force and increase the total distance travelled. Our hypothesis is that evolution has carefully tuned the air permeability of the seeds to operate in the most convenient fluid dynamic regime. To achieve final permeability, the primary and secondary fibres of the pappus have evolved with complex weaving; this maximises the drag force (i.e., the drag coefficient), and the pappus operates in an “optimal” state. We used computational fluid dynamics (CFD) simulations to compute the seed drag coefficient and compare it with data obtained from drop experiments. The permeability of the parachute was estimated from microscope images. Our simulations reveal three flow regimes in which the parachute can operate according to its permeability. These flow regimes impact the stability of the parachute and its drag coefficient. From the permeability measurements and drop experiments, we show how the seeds operate very close to the optimal case. The porosity of the textile appears to be an appropriate solution to achieve a lightweight structure that allows a low terminal velocity, a stable flight and a very efficient parachute for the velocity at which it operates. PMID:25938765
Casseau, Vincent; De Croon, Guido; Izzo, Dario; Pandolfi, Camilla
2015-01-01
Tragopogon pratensis is a small herbaceous plant that uses wind as the dispersal vector for its seeds. The seeds are attached to parachutes that increase the aerodynamic drag force and increase the total distance travelled. Our hypothesis is that evolution has carefully tuned the air permeability of the seeds to operate in the most convenient fluid dynamic regime. To achieve final permeability, the primary and secondary fibres of the pappus have evolved with complex weaving; this maximises the drag force (i.e., the drag coefficient), and the pappus operates in an "optimal" state. We used computational fluid dynamics (CFD) simulations to compute the seed drag coefficient and compare it with data obtained from drop experiments. The permeability of the parachute was estimated from microscope images. Our simulations reveal three flow regimes in which the parachute can operate according to its permeability. These flow regimes impact the stability of the parachute and its drag coefficient. From the permeability measurements and drop experiments, we show how the seeds operate very close to the optimal case. The porosity of the textile appears to be an appropriate solution to achieve a lightweight structure that allows a low terminal velocity, a stable flight and a very efficient parachute for the velocity at which it operates. PMID:25938765
Aerodynamics of a Cryogenic Semi-Tanker
NASA Astrophysics Data System (ADS)
Ortega, Jason; Salari, Kambiz
2009-11-01
The design of a modern cryogenic semi-tanker is based primarily upon functionality with little consideration given to aerodynamic drag. As a result, these tankers have maintained the appearance of a wheeled cylinder for several decades. To reduce the fuel usage of these vehicles, this study investigates their aerodynamics. A detailed understanding of the flow field about the vehicle and its influence on aerodynamic drag is obtained by performing Reynolds-Averaged Navier-Stokes simulations of a full-scale tractor and cryogenic tanker-trailer operating at highway speed within a crosswind. The tanker-trailer has a length to diameter ratio of 6.3. The Reynolds number, based upon the tanker diameter, is 4.0x10^6, while the effective vehicle yaw angle is 6.1 . The flow field about the vehicle is characterized by large flow separation regions at the tanker underbody and base. In addition, the relatively large gap between the tractor and the tanker-trailer allows the free-stream flow to be entrained into the tractor-tanker gap. By mitigating these drag-producing phenomena through the use of simple geometry modifications, it may be possible to reduce the aerodynamic drag of cryogenic semi-tankers and, thereby, improve their fuel economy. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.
NASA Technical Reports Server (NTRS)
Debra, Daniel B.
1989-01-01
A drag-free satellite cancels the effect of external disturbances. Although the forces may be small, a satellite is disturbed by residual air drag, radiation pressure, micrometeorite impact, and other small forces that act on its surface disturbing its orbit, which is principally determined by the gravity field. In some missions, these small perturbations that make the satellite deviate from its purely gravitational orbit are limiting. An internal unsupported proof mass is shielded by the satellite from the external disturbances. The position of the shield (or the main part of the satellite) is measured with respect to the internal proof mass, and this information is used to actuate a propulsion system which moves the satellite to follow the proof mass. A drag-free control system is illustrated. Since the proof mass is shielded it follows a purely gravitational orbit - as does the satellite following it - hence the name drag-free satellite. The idea was conceived by Lange (1964) and has been applied to many mission studies since. In some cases, it is not necessary to cancel the disturbances, only to measure them so they may be taken into account. In such cases, an accelerometer may be a more suitable solution (for example, using the ONERA Cactus or the Bell Aerosystems MESA).
NASA Technical Reports Server (NTRS)
Martin, D. M.; Mort, R. W.; Young, L. A.; Squires, P. K.
1993-01-01
New hub and pylon fairing designs were tested on a one-fifth scale Bell Helicopter Textron Model 222 helicopter with a bearingless main rotor hub. The blades were not installed for this test. The fairings were designed by NASA and Bell Helicopter Textron under a joint program and tested in the Ames Research Center 7-by 10-Foot Wind Tunnel. All six aircraft forces and moments were measured using the tunnel scales system. Previous research has identified the integrated hub and pylon fairing approach as the most efficient in reducing helicopter drag. Three hub fairings and three pylon fairings were tested (in various combinations) resulting in a total of 16 different configurations, including the baseline helicopter model without fairings. The geometry of the new fairings is described in detail. Test results are presented in the form of plots of the six model forces and moments. The data show that model drag can be reduced by as much as 20 percent by combining a small hub fairing (that has a circular arc upper surface and a flat lower surface) integrated with a nontapered pylon fairing. To minimize drag, the gap between the lower surface of the hub and upper surface of the pylon fairing must be kept to a minimum. Results show that the aerodynamic effects of the fairings on static longitudinal and directional stability can also be important.
Linear drag law for high-Reynolds-number flow past an oscillating body
NASA Astrophysics Data System (ADS)
Agre, Natalie; Childress, Stephen; Zhang, Jun; Ristroph, Leif
2016-07-01
An object immersed in a fast flow typically experiences fluid forces that increase with the square of speed. Here we explore how this high-Reynolds-number force-speed relationship is affected by unsteady motions of a body. Experiments on disks that are driven to oscillate while progressing through air reveal two distinct regimes: a conventional quadratic relationship for slow oscillations and an anomalous scaling for fast flapping in which the time-averaged drag increases linearly with flow speed. In the linear regime, flow visualization shows that a pair of counterrotating vortices is shed with each oscillation and a model that views a train of such dipoles as a momentum jet reproduces the linearity. We also show that appropriate scaling variables collapse the experimental data from both regimes and for different oscillatory motions into a single drag-speed relationship. These results could provide insight into the aerodynamic resistance incurred by oscillating wings in flight and they suggest that vibrations can be an effective means to actively control the drag on an object.
Investigation of Aerodynamic Capabilities of Flying Fish in Gliding Flight
NASA Astrophysics Data System (ADS)
Park, H.; Choi, H.
In the present study, we experimentally investigate the aerodynamic capabilities of flying fish. We consider four different flying fish models, which are darkedged-wing flying fishes stuffed in actual gliding posture. Some morphological parameters of flying fish such as lateral dihedral angle of pectoral fins, incidence angles of pectoral and pelvic fins are considered to examine their effect on the aerodynamic performance. We directly measure the aerodynamic properties (lift, drag, and pitching moment) for different morphological parameters of flying fish models. For the present flying fish models, the maximum lift coefficient and lift-to-drag ratio are similar to those of medium-sized birds such as the vulture, nighthawk and petrel. The pectoral fins are found to enhance the lift-to-drag ratio and the longitudinal static stability of gliding flight. On the other hand, the lift coefficient and lift-to-drag ratio decrease with increasing lateral dihedral angle of pectoral fins.
NASA Technical Reports Server (NTRS)
Mcgrath, Brian E.; Neuhart, Dan H.; Gatlin, Gregory M.; Oneil, Pat
1994-01-01
A flat-plate wind tunnel model of an advanced fighter configuration was tested in the NASA LaRC Subsonic Basic Research Tunnel and the 16- by 24-inch Water Tunnel. The test objectives were to obtain and evaluate the low-speed longitudinal aerodynamic characteristics of a candidate configuration for the integration of several new innovative wing designs. The flat plate test allowed for the initial evaluation of the candidate planform and was designated as the baseline planform for the innovative wing design study. Low-speed longitudinal aerodynamic data were obtained over a range of freestream dynamic pressures from 7.5 psf to 30 psf (M = 0.07 to M = 0.14) and angles-of-attack from 0 to 40 deg. The aerodynamic data are presented in coefficient form for the lift, induced drag, and pitching moment. Flow-visualization results obtained were photographs of the flow pattern over the flat plate model in the water tunnel for angles-of-attack from 10 to 40 deg. The force and moment coefficients and the flow-visualization photographs showed the linear and nonlinear aerodynamic characteristics due to attached flow and vortical flow over the flat plate model. Comparison between experiment and linear theory showed good agreement for the lift and induced drag; however, the agreement was poor for the pitching moment.
Aerodynamic Characterization of New Parachute Configurations for Low-Density Deceleration
NASA Technical Reports Server (NTRS)
Tanner, Christopher L.; Clark, Ian G.; Gallon, John C.; Rivellini, Tommaso P.; Witkowski, Allen
2013-01-01
The Low Density Supersonic Decelerator project performed a wind tunnel experiment on the structural design and geometric porosity of various sub-scale parachutes in order to inform the design of the 110ft nominal diameter flight test canopy. Thirteen different parachute configurations, including disk-gap-band, ring sail, disk sail, and star sail canopies, were tested at the National Full-scale Aerodynamics Complex 80- by 120-foot Wind Tunnel at NASA Ames Research Center. Canopy drag load, dynamic pressure, and canopy position data were recorded in order to quantify there lative drag performance and stability of the various canopies. Desirable designs would yield increased drag above the disk-gap-band with similar, or improved, stability characteristics. Ring sail parachutes were tested at geometric porosities ranging from 10% to 22% with most of the porosity taken from the shoulder region near the canopy skirt. The disk sail canopy replaced the rings lot portion of the ring sail canopy with a flat circular disk and wastested at geometric porosities ranging from 9% to 19%. The star sail canopy replaced several ringsail gores with solid gores and was tested at 13% geometric porosity. Two disk sail configurations exhibited desirable properties such as an increase of 6-14% in the tangential force coefficient above the DGB with essentially equivalent stability. However, these data are presented with caveats including the inherent differences between wind tunnel and flight behavior and qualitative uncertainty in the aerodynamic coefficients.
Micro air vehicle motion tracking and aerodynamic modeling
NASA Astrophysics Data System (ADS)
Uhlig, Daniel V.
Aerodynamic performance of small-scale fixed-wing flight is not well understood, and flight data are needed to gain a better understanding of the aerodynamics of micro air vehicles (MAVs) flying at Reynolds numbers between 10,000 and 30,000. Experimental studies have shown the aerodynamic effects of low Reynolds number flow on wings and airfoils, but the amount of work that has been conducted is not extensive and mostly limited to tests in wind and water tunnels. In addition to wind and water tunnel testing, flight characteristics of aircraft can be gathered through flight testing. The small size and low weight of MAVs prevent the use of conventional on-board instrumentation systems, but motion tracking systems that use off-board triangulation can capture flight trajectories (position and attitude) of MAVs with minimal onboard instrumentation. Because captured motion trajectories include minute noise that depends on the aircraft size, the trajectory results were verified in this work using repeatability tests. From the captured glide trajectories, the aerodynamic characteristics of five unpowered aircraft were determined. Test results for the five MAVs showed the forces and moments acting on the aircraft throughout the test flights. In addition, the airspeed, angle of attack, and sideslip angle were also determined from the trajectories. Results for low angles of attack (less than approximately 20 deg) showed the lift, drag, and moment coefficients during nominal gliding flight. For the lift curve, the results showed a linear curve until stall that was generally less than finite wing predictions. The drag curve was well described by a polar. The moment coefficients during the gliding flights were used to determine longitudinal and lateral stability derivatives. The neutral point, weather-vane stability and the dihedral effect showed some variation with different trim speeds (different angles of attack). In the gliding flights, the aerodynamic characteristics
Summary analysis of the Gemini entry aerodynamics
NASA Technical Reports Server (NTRS)
Whitnah, A. M.; Howes, D. B.
1972-01-01
The aerodynamic data that were derived in 1967 from the analysis of flight-generated data for the Gemini entry module are presented. These data represent the aerodynamic characteristics exhibited by the vehicle during the entry portion of Gemini 2, 3, 5, 8, 10, 11, and 12 missions. For the Gemini, 5, 8, 10, 11, and 12 missions, the flight-generated lift-to-drag ratios and corresponding angles of attack are compared with the wind tunnel data. These comparisons show that the flight generated lift-to-drag ratios are consistently lower than were anticipated from the tunnel data. Numerous data uncertainties are cited that provide an insight into the problems that are related to an analysis of flight data developed from instrumentation systems, the primary functions of which are other than the evaluation of flight aerodynamic performance.
Physics of badminton shuttlecocks. Part 1 : aerodynamics
NASA Astrophysics Data System (ADS)
Cohen, Caroline; Darbois Texier, Baptiste; Quéré, David; Clanet, Christophe
2011-11-01
We study experimentally shuttlecocks dynamics. In this part we show that shuttlecock trajectory is highly different from classical parabola. When one takes into account the aerodynamic drag, the flight of the shuttlecock quickly curves downwards and almost reaches a vertical asymptote. We solve the equation of motion with gravity and drag at high Reynolds number and find an analytical expression of the reach. At high velocity, this reach does not depend on velocity anymore. Even if you develop your muscles you will not manage to launch the shuttlecock very far because of the ``aerodynamic wall.'' As a consequence you can predict the length of the field. We then discuss the extend of the aerodynamic wall to other projectiles like sports balls and its importance.
Aerodynamic tests of Darrieus wind turbine blades
Migliore, P.G.; Walters, R.E.; Wolfe, W.P.
1983-03-01
An indoor facility for the aerodynamic testing of Darrieus turbine blades was developed. Lift, drag, and moment coefficients were measured for two blades whose angle of attack and chord-to-radius ratio were varied. The first blade used an NACA 0015 airfoil section; the second used a 15% elliptical cross section with a modified circular arc trailing edge. Blade aerodynamic coefficients were corrected to section coefficients for comparison to published rectilinear flow data. Although the airfoil sections were symmetrical, moment coefficients were not zero and the lift and drag curves were asymmetrical about zero lift coefficient and angle of attack. These features verified the predicted virtual camber and incidence phenomena. Boundary-layer centrifugal effects were manifested by discontinuous lift curves and large differences in the angle of zero lift between th NACA 0015 and elliptical airfoils. It was concluded that rectilinear flow aerodynamic data are not applicable to Darrieus turbine blades, even for small chord-to-radius ratios.
Asteroid orbit evolution due to thermal drag
NASA Technical Reports Server (NTRS)
Rubincam, David Parry
1995-01-01
Thermal drag, a variant of the Yarkovsky effect, may act on small asteroids with sizes from a few meters to a few tens of meters. Yarkovsky thermal drag comes from an asteroid's absorbing sunlight in the visible and reradiating it in the infrared. Since the infrared photons have momentum, by action-reaction, they kick the asteroid when they leave its surface. The reradiation, which is asymmetric in latitude over the asteroid, gives a net force along the asteroid's pole. Due to the asteroid's thermal inertia, averaging this force over one orbital period produces a net drag if the spin axis has a component in the orbital plane. Thermal drag tends to circularize orbits. It can increase or decrease orbital inclinations. An object whose spin axis points in random directions over its lifetime displays little change in orbital inclination. Thermal drag appears to have little to do with the delivery of chondrites from the asteroid belt; the thermal drag timescale (10(exp 8) years for meter-sizzed objects) is long compared with their cosmic ray exposure ages, and aphelia in the asteroid belt are not expected for mature thermal drag orbits. However, Yarkovsky thermal drag may act on the recently discovered near-Earth asteroids, which have radii of 10-30 m. Asteroid 1992 DA, for instance, might have its orbit shrunk by 0.1 AU in 3 x 10(exp 7) years, removing it from an Earth-crossing orbit. The near-Earth asteroids also tend to have small to moderate orbital eccentricities, as expected for highly evolved thermal drag objects. However, the time needed to bring them in from the asteroid belt (about 10(exp 9) years) is long compared with the collisonal and dynamical lifetimes (both about 10(exp 8) years) for Earth-crossing objects, arguing against their emplacement by thermal drag.
Configuration Aerodynamics: Past - Present - Future
NASA Technical Reports Server (NTRS)
Wood, Richard M.; Agrawal, Shreekant; Bencze, Daniel P.; Kulfan, Robert M.; Wilson, Douglas L.
1999-01-01
The Configuration Aerodynamics (CA) element of the High Speed Research (HSR) program is managed by a joint NASA and Industry team, referred to as the Technology Integration Development (ITD) team. This team is responsible for the development of a broad range of technologies for improved aerodynamic performance and stability and control characteristics at subsonic to supersonic flight conditions. These objectives are pursued through the aggressive use of advanced experimental test techniques and state of the art computational methods. As the HSR program matures and transitions into the next phase the objectives of the Configuration Aerodynamics ITD are being refined to address the drag reduction needs and stability and control requirements of High Speed Civil Transport (HSCT) aircraft. In addition, the experimental and computational tools are being refined and improved to meet these challenges. The presentation will review the work performed within the Configuration Aerodynamics element in 1994 and 1995 and then discuss the plans for the 1996-1998 time period. The final portion of the presentation will review several observations of the HSR program and the design activity within Configuration Aerodynamics.
NASA Astrophysics Data System (ADS)
Brown, A. P.; Feik, R. A.
1983-12-01
This memo presents a preliminary study of a proposed method of measuring the aerodynamic forces on a supported model in an intermittent very short duration wind tunnel with a relatively high airflow dynamic pressure (of the orders of 200 microsec and 1/3 atmosphere respectively). A semiconductor strain gauged cantilever beam balance is used to record strain time histories associated with model displacement in response to aerodynamic force. The practical feasibility of obtaining sufficiently resolvable strains for the prescribed tunnel conditions with the given strain gauge configuration is established. The proposed method uses a system identification procedure to determine the system dynamic response characteristics using a known calibration force input. Subsequently, aerodynamic forces during a tunnel run follow from the recorded strain gauge time histories. The procedure has been demonstrated successfully using simulated data. However, the experimental situation did not lead to a successful analysis in the way proposed. Reasons for this are discussed and recommendations made for improvements. A brief series of shots in the ANU free piston shock tunnel also highlights the need to isolate as much as possible the model/balance from external vibrations.
Comparisons of AEROX computer program predictions of lift and induced drag with flight test data
NASA Technical Reports Server (NTRS)
Axelson, J.; Hill, G. C.
1981-01-01
The AEROX aerodynamic computer program which provides accurate predictions of induced drag and trim drag for the full angle of attack range and for Mach numbers from 0.4 to 3.0 is described. This capability is demonstrated comparing flight test data and AEROX predictions for 17 different tactical aircraft. Values of minimum (skin friction, pressure, and zero lift wave) drag coefficients and lift coefficient offset due to camber (when required) were input from the flight test data to produce total lift and drag curves. The comparisons of trimmed lift drag polars show excellent agreement between the AEROX predictions and the in flight measurements.
Aerodynamics of a cycling team in a time trial: does the cyclist at the front benefit?
NASA Astrophysics Data System (ADS)
Íñiguez-de-la Torre, A.; Íñiguez, J.
2009-11-01
When seasonal journeys take place in nature, birds and fishes migrate in groups. This provides them not only with security but also a considerable saving of energy. The power they need to travel requires overcoming aerodynamic or hydrodynamic drag forces, which can be substantially reduced when the group travels in an optimal arrangement. Also in this area, humans imitate nature, which is especially evident in the practice of outdoor sports and motor competitions. Cycle races, in which speeds of up to 15 m s-1 are frequent, offer great opportunities to appreciate the advantage of travelling in a group. Here we present a brief analysis of the aerodynamics of a cycling team in a time-trial challenge, showing how each rider is favoured according to his position in the group. We conclude that the artificial tail wind created by the team also benefits the cyclist at the front by about 5%.
Solute drag on perfect and extended dislocations
NASA Astrophysics Data System (ADS)
Sills, R. B.; Cai, W.
2016-04-01
The drag force exerted on a moving dislocation by a field of mobile solutes is studied in the steady state. The drag force is numerically calculated as a function of the dislocation velocity for both perfect and extended dislocations. The sensitivity of the non-dimensionalized force-velocity curve to the various controlling parameters is assessed, and an approximate analytical force-velocity expression is given. A non-dimensional parameter S characterizing the strength of the solute-dislocation interaction, the background solute fraction ?, and the dislocation character angle ?, are found to have the strongest influence on the force-velocity curve. Within the model considered here, a perfect screw dislocation experiences no solute drag, but an extended screw dislocation experiences a non-zero drag force that is about 10 to 30% of the drag on an extended edge dislocation. The solutes can change the spacing between the Shockley partials in both stationary and moving extended dislocations, even when the stacking fault energy remains unaltered. Under certain conditions, the solutes destabilize an extended dislocation by either collapsing it into a perfect dislocation or causing the partials to separate unboundedly. It is proposed that the latter instability may lead to the formation of large faulted areas and deformation twins in low stacking fault energy materials containing solutes, consistent with experimental observations of copper and stainless steel containing hydrogen.
Thermal Casimir drag in fluctuating classical fields
NASA Astrophysics Data System (ADS)
Démery, Vincent; Dean, David S.
2011-07-01
A uniformly moving inclusion which locally suppresses the fluctuations of a classical thermally excited field is shown to experience a drag force that depends on the dynamics of the field. It is shown that in a number of cases the linear friction coefficient is dominated by short distance fluctuations and takes a very simple form. Examples where this drag can occur are for stiff objects, such as proteins, nonspecifically bound to more flexible ones such as polymers and membranes.
Aeroacoustic Study of a High-Fidelity Aircraft Model: Part 1- Steady Aerodynamic Measurements
NASA Technical Reports Server (NTRS)
Khorrami, Mehdi R.; Hannon, Judith A.; Neuhart, Danny H.; Markowski, Gregory A.; VandeVen, Thomas
2012-01-01
In this paper, we present steady aerodynamic measurements for an 18% scale model of a Gulfstream air-craft. The high fidelity and highly-instrumented semi-span model was developed to perform detailed aeroacoustic studies of airframe noise associated with main landing gear/flap components and gear-flap interaction noise, as well as to evaluate novel noise reduction concepts. The aeroacoustic tests, being conducted in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel, are split into two entries. The first entry, completed November 2010, was entirely devoted to the detailed mapping of the aerodynamic characteristics of the fabricated model. Flap deflections of 39?, 20?, and 0? with the main landing gear on and off were tested at Mach numbers of 0.16, 0.20, and 0.24. Additionally, for each flap deflection, the model was tested with the tunnel both in the closed-wall and open-wall (jet) modes. During this first entry, global forces (lift and drag) and extensive steady and unsteady surface pressure measurements were obtained. Preliminary analysis of the measured forces indicates that lift, drag, and stall characteristics compare favorably with Gulfstream?s high Reynolds number flight data. The favorable comparison between wind-tunnel and flight data allows the semi-span model to be used as a test bed for developing/evaluating airframe noise reduction concepts under a relevant environment. Moreover, initial comparison of the aerodynamic measurements obtained with the tunnel in the closed- and open-wall configurations shows similar aerodynamic behavior. This permits the acoustic and off-surface flow measurements, planned for the second entry, to be conducted with the tunnel in the open-jet mode.
A fundamental study of drag and an assessment of conventional drag-due-to-lift reduction devices
NASA Technical Reports Server (NTRS)
Yates, J. E.; Donald, C. D.
1986-01-01
The integral conservation laws of fluid mechanics are used to assess the drag efficiency of lifting wings, both CTOL and various out-of-plane configurations. The drag-due-to-lift is separated into two major components: (1) the induced drag-due-to-lift that depends on aspect ratio but is relatively independent of Reynolds number; (2) the form drag-due-to-lift that is independent of aspect ratio but dependent on the details of the wing section design, planform and Reynolds number. For each lifting configuration there is an optimal load distribution that yields the minimum value of drag-due-to-lift. For well designed high aspect ratio CTOL wings the two drag components are independent. With modern design technology CTOL wings can be (and usually are) designed with a drag-due-to-lift efficiency close to unity. Wing tip-devices (winglets, feathers, sails, etc.) can improve drag-due-to-lift efficiency by 10 to 15% if they are designed as an integral part of the wing. As add-on devices they can be detrimental. It is estimated that 25% improvements of wing drag-due-to-lift efficiency can be obtained with joined tip configurations and vertically separated lifting elements without considering additional benefits that might be realized by improved structural efficiency. It is strongly recommended that an integrated aerodynamic/structural approach be taken in the design of (or research on) future out-of-plane configurations.
Flow drag and heat transfer characteristics of drag-reducing nanofluids with CuO nanoparticles
NASA Astrophysics Data System (ADS)
Wang, Ping-Yang; Wang, Xue-Jiao; Liu, Zhen-Hua
2016-05-01
A new kind of aqueous CuO nanofluid with drag-reducing performance was developed. The new working fluid was an aqueous CTAC (cetyltrimethyl ammonium chloride) solution with CuO nanoparticles added and has both special effects of drag-reducing and heat transfer enhancement. An experiment was carried out to investigate the forced convective flow and heat transfer characteristics of conventional drag reducing fluid (aqueous CTAC solution) and the new drag-reducing nanofluid in a test tube with an inner diameter of 25.6 mm. Results indicated that there were no obvious differences of the drag-reducing characteristics between conventional drag reducing fluid and new drag-reducing nanofluid. However, their heat transfer characteristics were obvious different. The heat transfer characteristics of the new drag-reducing nanofluid significantly depend on the liquid temperature, the nanoparticle concentration and the CTAC concentration. The heat transfer enhancement technology of nanofluid could be applied to solve the problem of heat transfer deterioration for conventional drag-reducing fluids.
Drag and lift reduction of a 3D bluff-body using active vortex generators
NASA Astrophysics Data System (ADS)
Aider, Jean-Luc; Beaudoin, Jean-François; Wesfreid, José Eduardo
2010-05-01
In this study, a passive flow control experiment on a 3D bluff-body using vortex generators (VGs) is presented. The bluff-body is a modified Ahmed body (Ahmed in J Fluids Eng 105:429-434 1983) with a curved rear part, instead of a slanted one, so that the location of the flow separation is no longer forced by the geometry. The influence of a line of non-conventional trapezoïdal VGs on the aerodynamic forces (drag and lift) induced on the bluff-body is investigated. The high sensitivity to many geometric (angle between the trapezoïdal element and the wall, spanwise spacing between the VGs, longitudinal location on the curved surface) and physical (freestream velocity) parameters is clearly demonstrated. The maximum drag reduction is -12%, while the maximum global lift reduction can reach more than -60%, with a strong dependency on the freestream velocity. For some configurations, the lift on the rear axle of the model can be inverted (-104%). It is also shown that the VGs are still efficient even downstream of the natural separation line. Finally, a dynamic parameter is chosen and a new set-up with motorized vortex generators is proposed. Thanks to this active device. The optimal configurations depending on two parameters are found more easily, and a significant drag and lift reduction (up to -14% drag reduction) can be reached for different freestream velocities. These results are then analyzed through wall pressure and velocity measurements in the near-wake of the bluff-body with and without control. It appears that the largest drag and lift reduction is clearly associated to a strong increase of the size of the recirculation bubble over the rear slant. Investigation of the velocity field in a cross-section downstream the model reveals that, in the same time, the intensity of the longitudinal trailing vortices is strongly reduced, suggesting that the drag reduction is due to the breakdown of the balance between the separation bubble and the longitudinal vortices
Ion wake effects on the Coulomb ion drag in complex dusty plasmas
Ki, Dae-Han; Jung, Young-Dae
2010-09-06
The ion wake effects on the Coulomb drag force are investigated in complex dusty plasmas. It is shown that the ion wake effects significantly enhance the Coulomb ion drag force. It is also found that the ion wake effects on the Coulomb drag force increase with an increase in the Debye length. In addition, the ion wake effects on the momentum transfer cross section and Coulomb drag force are found to be increased with increasing thermal Mach number, i.e., decreasing plasma temperature. It is also found that the Coulomb ion drag force would be stronger for smaller dust grains.
CME propagation: where does solar wind drag 'take over'?
NASA Astrophysics Data System (ADS)
Subramanian, P.
2013-12-01
Coronal mass ejections (CMEs) from the Sun are known to be acted upon by driving as well as drag forces. They are generally thought to be driven by Lorentz self-forces, while the drag is due to viscous interaction with the ambient solar wind. However, the typical heliocentric distances at which driving forces cease to be dominant (and solar wind drag becomes important) is not obvious for most CMEs. We use a recently developed microphysical model for solar wind viscous drag (Subramanian, Lara and Borgazzi 2012) together with data for driving forces from a well observed set of flux rope CMEs to answer this question. These results are important for building quantitative models for CME propagation, especially for those CMEs which are not fast enough for one to assume that they are acted upon primarily by drag forces.
NASA Technical Reports Server (NTRS)
Baize, Daniel G. (Editor)
1999-01-01
The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Aerodynamic Performance Workshop on February 25-28, 1997. The workshop was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in area of Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization), High-Lift, Flight Controls, Supersonic Laminar Flow Control, and Sonic Boom Prediction. The workshop objectives were to (1) report the progress and status of HSCT aerodyamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientist and engineers working HSCT aerodynamics. In particular, single- and multi-point optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT Motion Simulator results were presented along with executive summaries for all the Aerodynamic Performance technology areas.
Applicability of commercial CFD tools for assessment of heavy vehicle aerodynamic characteristics.
Pointer, W. D.; Sofu, T.; Chang, J.; Weber, D.; Nuclear Engineering Division
2008-12-01
In preliminary validation studies, computational predictions from the commercial CFD codes Star-CD were compared with detailed velocity, pressure and force balance data from experiments completed in the 7 ft. by 10 ft. wind tunnel at NASA Ames using a Generic Conventional Model (GCM) that is representative of typical current-generation tractor-trailer geometries. Lessons learned from this validation study were then applied to the prediction of aerodynamic drag impacts associated with various changes to the GCM geometry, including the addition of trailer based drag reduction devices and modifications to the radiator and hood configuration. Add-on device studies have focused on ogive boat tails, with initial results indicating that a seven percent reduction in drag coefficient is easily achievable. Radiator and hood reconfiguration studies have focused on changing only the size of the radiator and angle of the hood components without changes to radii of curvature between the radiator grill and hood components. Initial results indicate that such changes lead to only modest changes in drag coefficient.
Analytical observations on the aerodynamics of a delta wing with leading edge flaps
NASA Technical Reports Server (NTRS)
Oh, S.; Tavella, D.
1986-01-01
The effect of a leading edge flap on the aerodynamics of a low aspect ratio delta wing is studied analytically. The separated flow field about the wing is represented by a simple vortex model composed of a conical straight vortex sheet and a concentrated vortex. The analysis is carried out in the cross flow plane by mapping the wing trace, by means of the Schwarz-Christoffel transformation into the real axis of the transformed plane. Particular attention is given to the influence of the angle of attack and flap deflection angle on lift and drag forces. Both lift and drag decrease with flap deflection, while the lift-to-drag ratioe increases. A simple coordinate transformation is used to obtain a closed form expression for the lift-to-drag ratio as a function of flap deflection. The main effect of leading edge flap deflection is a partial suppression of the separated flow on the leeside of the wing. Qualitative comparison with experiments is presented, showing agreement in the general trends.
Aerodynamic Design Opportunities for Future Supersonic Aircraft
NASA Technical Reports Server (NTRS)
Wood, Richard M.; Bauer, Steven X. S.; Flamm, Jeffrey D.
2002-01-01
A discussion of a diverse set of aerodynamic opportunities to improve the aerodynamic performance of future supersonic aircraft has been presented and discussed. These ideas are offered to the community in a hope that future supersonic vehicle development activities will not be hindered by past efforts. A number of nonlinear flow based drag reduction technologies are presented and discussed. The subject technologies are related to the areas of interference flows, vehicle concepts, vortex flows, wing design, advanced control effectors, and planform design. The authors also discussed the importance of improving the aerodynamic design environment to allow creativity and knowledge greater influence. A review of all of the data presented show that pressure drag reductions on the order of 50 to 60 counts are achievable, compared to a conventional supersonic cruise vehicle, with the application of several of the discussed technologies. These drag reductions would correlate to a 30 to 40% increase in cruise L/D (lift-to-drag ratio) for a commercial supersonic transport.
Statistical Analysis of CFD Solutions from the Drag Prediction Workshop
NASA Technical Reports Server (NTRS)
Hemsch, Michael J.
2002-01-01
A simple, graphical framework is presented for robust statistical evaluation of results obtained from N-Version testing of a series of RANS CFD codes. The solutions were obtained by a variety of code developers and users for the June 2001 Drag Prediction Workshop sponsored by the AIAA Applied Aerodynamics Technical Committee. The aerodynamic configuration used for the computational tests is the DLR-F4 wing-body combination previously tested in several European wind tunnels and for which a previous N-Version test had been conducted. The statistical framework is used to evaluate code results for (1) a single cruise design point, (2) drag polars and (3) drag rise. The paper concludes with a discussion of the meaning of the results, especially with respect to predictability, Validation, and reporting of solutions.
NASA Technical Reports Server (NTRS)
James, Carlton S.
1960-01-01
An aircraft configuration, previously conceived as a means to achieve favorable aerodynamic stability characteristics., high lift-drag ratio, and low heating rates at high supersonic speeds., was modified in an attempt to increase further the lift-drag ratio without adversely affecting the other desirable characteristics. The original configuration consisted of three identical triangular wing panels symmetrically disposed about an ogive-cylinder body equal in length to the root chord of the panels. This configuration was modified by altering the angular disposition of the wing panels, by reducing the area of the panel forming the vertical fin, and by reshaping the body to produce interference lift. Six-component force and moment tests of the modified configuration at combined angles of attack and sideslip were made at a Mach number of 3.3 and a Reynolds number of 5.46 million. A maximum lift-drag ratio of 6.65 (excluding base drag) was measured at a lift coefficient of 0.100 and an angle of attack of 3.60. The lift-drag ratio remained greater than 3 up to lift coefficient of 0.35. Performance estimates, which predicted a maximum lift-drag ratio for the modified configuration 27 percent greater than that of the original configuration, agreed well with experiment. The modified configuration exhibited favorable static stability characteristics within the test range. Longitudinal and directional centers of pressure were slightly aft of the respective centroids of projected plan-form and side area.
Drag reductions obtained by modifying a box-shaped ground vehicle
NASA Technical Reports Server (NTRS)
Saltzman, E. J.; Meyer, R. R., Jr.; Lux, D. P.
1974-01-01
A box-shaped ground vehicle was used to simulate the aerodynamic drag of high volume transports, that is, delivery vans, trucks, or motor homes. The coast-down technique was used to define the drag of the original vehicle, having all square corners, and several modifications of the vehicle. Test velocities ranged up to 65 miles per hour, which provided maximum Reynolds numbers of 1 times 10 to the 7th power based on vehicle length. One combination of modifications produced a reduction in aerodynamic drag of 61 percent as compared with the original square-cornered vehicle.
Vorticity Confinement Applied to Turbulent Wing Tip Vortices for Wake-Integral Drag Prediction
NASA Astrophysics Data System (ADS)
Pierson, Kristopher; Povitsky, Alex
2013-11-01
In the current study the vorticity confinement (VC) approach was applied to tip vortices shed by edges of stationary wings in order to predict induced drag by far-field integration in Trefftz plane. The VC parameter was evaluated first by application to convection of vortices in 2-D uniform flow and then to tip vortices shed in 3-D simulation of finite-aspect ratio rectangular wing in subsonic flight. Dependence of VC parameter on the flight Mach number and the angle of attack was evaluated. The aerodynamic drag results with application of VC to prevent numerical diffusion are much closer to analytic lifting line theory compared to integration over surface of wing while the viscous profile drag is more accurately evaluated by surface integration. To apply VC to viscous and turbulent flows, it is shown that VC does not affect the physical rate of dissipation of vortices in viscous/turbulent flows at time scales corresponding to convection of vortices from the wing to Trefftz plane of integration. To account for turbulent effects on tip vortices, VC was applied in combination with Spalart-Allmaras, k- ɛ, and six Reynolds stresses models of turbulence. The results are compared to experiments to validate the physical dissipation of tip vortex. This research was supported by The Dayton Area Graduate Studies Institute (DAGSI) and US Air Force Research Laboratory (AFRL) grants in 2009-2013, US Army Research Office (ARO) in 2012-2013 and ASEE/AFRL summer faculty grant.
NASA Technical Reports Server (NTRS)
Hahne, David E. (Editor)
1999-01-01
NASA's High-Speed Research Program sponsored the 1999 Aerodynamic Performance Technical Review on February 8-12, 1999 in Anaheim, California. The review was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in the areas of Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization), High Lift, and Flight Controls. The review objectives were to: (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientists and engineers working on HSCT aerodynamics. In particular, single and midpoint optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT simulation results were presented, along with executive summaries for all the Aerodynamic Performance technology areas. The HSR Aerodynamic Performance Technical Review was held simultaneously with the annual review of the following airframe technology areas: Materials and Structures, Environmental Impact, Flight Deck, and Technology Integration. Thus, a fourth objective of the Review was to promote synergy between the Aerodynamic Performance technology area and the other technology areas of the HSR Program. This Volume 1/Part 1 publication covers configuration aerodynamics.
Narang, Ajit S; Sheverev, Valery; Freeman, Tim; Both, Douglas; Stepaniuk, Vadim; Delancy, Michael; Millington-Smith, Doug; Macias, Kevin; Subramanian, Ganeshkumar
2016-01-01
Drag flow force (DFF) sensor that measures the force exerted by wet mass in a granulator on a thin cylindrical probe was shown as a promising process analytical technology for real-time in-line high-resolution monitoring of wet mass consistency during high shear wet granulation. Our previous studies indicated that this process analytical technology tool could be correlated to granulation end point established independently through drug product critical quality attributes. In this study, the measurements of flow force by a DFF sensor, taken during wet granulation of 3 placebo formulations with different binder content, are compared with concurrent at line FT4 Powder Rheometer characterization of wet granules collected at different time points of the processing. The wet mass consistency measured by the DFF sensor correlated well with the granulation's resistance to flow and interparticulate interactions as measured by FT4 Powder Rheometer. This indicated that the force pulse magnitude measured by the DFF sensor was indicative of fundamental material properties (e.g., shear viscosity and granule size/density), as they were changing during the granulation process. These studies indicate that DFF sensor can be a valuable tool for wet granulation formulation and process development and scale up, as well as for routine monitoring and control during manufacturing. PMID:26852853
Reconfiguration parameters for drag of flexible cylindrical elements
NASA Astrophysics Data System (ADS)
John, Chapman; Wilson, Bruce; Gulliver, John
2015-11-01
This presentation compares parameters that characterize reconfiguration effects on flow resistance and drag. The drag forces occurring on flexible bluff bodies are different from the drag occurring on rigid bluff bodies due to reconfiguration. Drag force data, collected using a torque sensor in a flume, for simple cylindrical obstructions of the same shape and size but with different flexibility is used to fit drag parameters. The key parameter evaluated is a reference velocity factor u to account for drag reduction due to reconfiguration, similar to a Vogel exponent. Our equations preserves the traditional exponent of the drag relationship, but places a factor onto the drag coefficient for flexible elements, rather than a Vogel exponent arrangement applied to the flow velocity. Additionally we relate the reference velocity factor u to the modulus of elasticity of the material through the Cauchy Number. The use of a reference velocity factor u in place of a Vogel exponent appears viable to account for how the drag forces are altered by reconfiguration. The proposed formulation for drag reduction is more consistently estimated for the range of flexibilities in this study. Unfortunately, the mechanical properties of vegetation are not often readily available for reconfiguration relationships to the elastic modulus of vegetation to be of immediate practical use.
Han, Jong-Seob; Kim, Joong-Kwan; Chang, Jo Won; Han, Jae-Hung
2015-08-01
A quasi-steady aerodynamic model in consideration of the center of pressure (C.P.) was developed for insect flight. A dynamically scaled-up robotic hawkmoth wing was used to obtain the translational lift, drag, moment and rotational force coefficients. The translational force coefficients were curve-fitted with respect to the angles of attack such that two coefficients in the Polhamus leading-edge suction analogy model were obtained. The rotational force coefficient was also compared to that derived by the standard Kutta-Joukowski theory. In order to build the accurate pitching moment model, the locations of the C.Ps. and its movements depending on the pitching velocity were investigated in detail. We found that the aerodynamic moment model became suitable when the rotational force component was assumed to act on the half-chord. This implies that the approximation borrowed from the conventional airfoil concept, i.e., the 'C.P. at the quarter-chord' may lead to an incorrect moment prediction. In the validation process, the model showed excellent time-course force and moment estimations in comparison with the robotic wing measurement results. A fully nonlinear multibody flight dynamic simulation was conducted to check the effect of the traveling C.P. on the overall flight dynamics. This clearly showed the importance of an accurate aerodynamic moment model. PMID:26226478
Techniques for estimating Space Station aerodynamic characteristics
NASA Technical Reports Server (NTRS)
Thomas, Richard E.
1993-01-01
A method was devised and calculations were performed to determine the effects of reflected molecules on the aerodynamic force and moment coefficients for a body in free molecule flow. A procedure was developed for determining the velocity and temperature distributions of molecules reflected from a surface of arbitrary momentum and energy accommodation. A system of equations, based on momentum and energy balances for the surface, incident, and reflected molecules, was solved by a numerical optimization technique. The minimization of a 'cost' function, developed from the set of equations, resulted in the determination of the defining properties of the flow reflected from the arbitrary surface. The properties used to define both the incident and reflected flows were: average temperature of the molecules in the flow, angle of the flow with respect to a vector normal to the surface, and the molecular speed ratio. The properties of the reflected flow were used to calculate the contribution of multiply reflected molecules to the force and moments on a test body in the flow. The test configuration consisted of two flat plates joined along one edge at a right angle to each other. When force and moment coefficients of this 90 deg concave wedge were compared to results that did not include multiple reflections, it was found that multiple reflections could nearly double lift and drag coefficients, with nearly a 50 percent increase in pitching moment for cases with specular or nearly specular accommodation. The cases of diffuse or nearly diffuse accommodation often had minor reductions in axial and normal forces when multiple reflections were included. There were several cases of intermediate accommodation where the addition of multiple reflection effects more than tripled the lift coefficient over the convex technique.
NASA Technical Reports Server (NTRS)
Penland, Jim A.
1961-01-01
Force tests of a series of right circular cones having semivertex angles ranging from 5 deg to 45 deg and a series of right circular cone-cylinder configurations having semivertex angles ranging from 5 deg to 20 deg and an afterbody fineness ratio of 6 have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.83, a Reynolds number of 0.24 x 10.6 per inch, and angles of attack up to 130 deg. An analysis of the results made use of the Newtonian and modified Newtonian theories and the exact theory. A comparison of the experimental data of both cone and cone-cylinder configurations with theoretical calculations shows that the Newtonian concept gives excellent predictions of trends of the force characteristics and the locations with respect to angle of attack of the points of maximum lift, maximum drag, and maximum lift-drag ratio. Both the Newtonian a.nd exact theories give excellent predictions of the sign and value of the initial lift-curve slope. The maximum lift coefficient for conical bodies is nearly constant at a value of 0.5 based on planform area for semivertex angles up to 30 deg. The maximum lift-drag ratio for conical bodies can be expected to be not greater than about 3.5, and this value might be expected only for slender cones having semivertex angles of less than 5 deg. The increments of angle of attack and lift coefficient between the maximum lift-drag ratio and the maximum lift coefficient for conical bodies decrease rapidly with increasing semivertex angles as predicted by the modified Newtonian theory.
Robert J. Englar
2000-06-19
Under contract to the DOE Office of Heavy Vehicle Technologies, the Georgia Tech Research Institute (GTRI) is developing and evaluating pneumatic (blown) aerodynamic devices to improve the performance, economics, stability and safety of operation of Heavy Vehicles. The objective of this program is to apply the pneumatic aerodynamic aircraft technology previously developed and flight-tested by GTRI personnel to the design of an efficient blown tractor-trailer configuration. Recent experimental results obtained by GTRI using blowing have shown drag reductions of 35% on a streamlined automobile wind-tunnel model. Also measured were lift or down-load increases of 100-150% and the ability to control aerodynamic moments about all 3 axes without any moving control surfaces. Similar drag reductions yielded by blowing on bluff afterbody trailers in current US trucking fleet operations are anticipated to reduce yearly fuel consumption by more than 1.2 billion gallons, while even further reduction is possible using pneumatic lift to reduce tire rolling resistance. Conversely, increased drag and down force generated instantaneously by blowing can greatly increase braking characteristics and control in wet/icy weather due to effective ''weight'' increases on the tires. Safety is also enhanced by controlling side loads and moments caused on these Heavy Vehicles by winds, gusts and other vehicles passing. This may also help to eliminate the jack-knifing problem if caused by extreme wind side loads on the trailer. Lastly, reduction of the turbulent wake behind the trailer can reduce splash and spray patterns and rough air being experienced by following vehicles. To be presented by GTRI in this paper will be results developed during the early portion of this effort, including a preliminary systems study, CFD prediction of the blown flowfields, and design of the baseline conventional tractor-trailer model and the pneumatic wind-tunnel model.
NASA Technical Reports Server (NTRS)
Alford, William J; King, Thomas, Jr
1957-01-01
An investigation was made at high subsonic speeds in the Langley high-speed 7- by 10-foot tunnel to determine the static aerodynamic forces and moments on a missile model during simulated launching from the midsemispan location of a 45 degree sweptback wing-fuselage-pylon combination. The results indicated significant variations in all the aerodynamic components with changes in chordwise location of the missile. Increasing the angle of attack caused increases in the induced effects on the missile model because of the wing-fuselage-pylon combination. Increasing the Mach number had little effect on the variations of the missile aerodynamic characteristics with angle of attack except that nonlinearities were incurred at smaller angles of attack for the higher Mach numbers. The effects of finite wing thickness on the missile characteristics, at zero angle of attack, increase with increasing Mach number. The effects of the pylon on the missile characteristics were to causeincreases in the rolling-moment variation with angle of attack and a negative displacement of the pitching-moment curves at zero angle of attack. The effects of skewing the missile in the lateral direction relative to and sideslipping the missile with the wing-fuselage-pylon combination were to cause additional increments in side force at zero angle of attack. For the missile yawing moments the effects of changes in skew or sideslip angles were qualitatively as would be expected from consideration of the isolated missile characteristics, although there existed differences in theyawing-moment magnitudes.
NASA Technical Reports Server (NTRS)
Campbell, Bryan A.; Bezos, Gaudy M.; Dunham, R. Earl, Jr.; Melson, W. Edward, Jr.
1990-01-01
One of the necessary areas of consideration for outdoor heavy rain testing is the effect of wind on both the simulated rain field and the quality and repeatability of the aerodynamic data. This paper discusses the data acquisition and subsequent reduction to nondimensional coefficients of lift and drag, with the appropriate correction for wind and rain field. Sample force data showing these effects are presented, along with estimates for accuracy and repeatability. The capability to produce high-quality data for rain drop size distribution using photographic and computerized image processing techniques was developed. Sample photographs depicting rain drop size are shown.
Real-Time Adaptive Least-Squares Drag Minimization for Performance Adaptive Aeroelastic Wing
NASA Technical Reports Server (NTRS)
Ferrier, Yvonne L.; Nguyen, Nhan T.; Ting, Eric
2016-01-01
This paper contains a simulation study of a real-time adaptive least-squares drag minimization algorithm for an aeroelastic model of a flexible wing aircraft. The aircraft model is based on the NASA Generic Transport Model (GTM). The wing structures incorporate a novel aerodynamic control surface known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The drag minimization algorithm uses the Newton-Raphson method to find the optimal VCCTEF deflections for minimum drag in the context of an altitude-hold flight control mode at cruise conditions. The aerodynamic coefficient parameters used in this optimization method are identified in real-time using Recursive Least Squares (RLS). The results demonstrate the potential of the VCCTEF to improve aerodynamic efficiency for drag minimization for transport aircraft.
NASA Technical Reports Server (NTRS)
Roskam, J.
1975-01-01
A discussion of data of and methods for predicting trim drag is presented. Specifically the following subjects are discussed: (1) economic impact of trim drag; (2) the trim drag problem in propeller driven airplanes and the effect of propeller and nacelle location; (3) theoretical procedures for predicting trim drag; and (4) research needs in the area of trim drag.
Experimental drag histories of shocked spherical particles
NASA Astrophysics Data System (ADS)
Prestridge, Katherine; Orlicz, Greg; Martinez, Adam
2015-11-01
The horizontal shock tube (HST) facility at Los Alamos is used to investigate the drag forces on micrometer-sized particles dispersed in air when they are accelerated by a shock. Eight-frame, high-speed particle tracking velocimetry/accelerometry (PTVA) diagnostics are implemented to measure the trajectory of individual particles with high spatial and temporal resolution, and a shadowgraphy system is used to measure the shock position on each image. We present experiments over a range of Reynolds numbers, Mach numbers, particle sizes, and particle densities that explore the drag forces on solid, spherical, non-deforming particles. Experimental drag coefficients are calculated from eight dynamic measurements of particle position versus time, for Mach 1.3 and Mach 1.2 experiments. Experimental results show drag coefficients significantly larger than those predicted by the standard drag model for solid, spherical particles. These results are consistent with measurements made by Rudinger (1970) and Sommerfeld (1985). We will present experimental results and analysis of unsteady drag as a function of particle Reynolds number, Mach number and Stokes number.
Ion drag on dust grains in electronegative plasmas
Denysenko, I.; Yu, M.Y.; Stenflo, L.; Azarenkov, N.A.
2005-04-15
The electric and the positive- and negative-ion drag forces on a dust grain in an electronegative complex plasma are investigated. It is shown that the number of locations where the drag forces balance the electric force is considerably larger than that in an electropositive plasma. The balance occurs in the so-called oscillation regime where the electric field oscillates in space. The effect of the negative-ion drag force on the dust grain can be substantial in a certain parameter range.
Covariance analysis of differential drag-based satellite cluster flight
NASA Astrophysics Data System (ADS)
Ben-Yaacov, Ohad; Ivantsov, Anatoly; Gurfil, Pini
2016-06-01
One possibility for satellite cluster flight is to control relative distances using differential drag. The idea is to increase or decrease the drag acceleration on each satellite by changing its attitude, and use the resulting small differential acceleration as a controller. The most significant advantage of the differential drag concept is that it enables cluster flight without consuming fuel. However, any drag-based control algorithm must cope with significant aerodynamical and mechanical uncertainties. The goal of the current paper is to develop a method for examination of the differential drag-based cluster flight performance in the presence of noise and uncertainties. In particular, the differential drag control law is examined under measurement noise, drag uncertainties, and initial condition-related uncertainties. The method used for uncertainty quantification is the Linear Covariance Analysis, which enables us to propagate the augmented state and filter covariance without propagating the state itself. Validation using a Monte-Carlo simulation is provided. The results show that all uncertainties have relatively small effect on the inter-satellite distance, even in the long term, which validates the robustness of the used differential drag controller.
Air flow testing on aerodynamic truck
NASA Technical Reports Server (NTRS)
1975-01-01
After leasing a cab-over tractor-trailer from a Southern California firm, Dryden researchers added sheet metal modifications like those shown here. They rounded the front corners and edges, and placed a smooth fairing on the cab's roofs and sides extending back to the trailer. During the investigation of truck aerodynamics, the techniques honed in flight research proved highly applicable. By closing the gap between the cab and the trailer, for example, researchers discovered a significant reduction in aerodynamic drag, one resulting in 20 to 25 percent less fuel consumption than the standard design. Many truck manufacturers subsequently incorporated similar modifications on their products.
NASA Astrophysics Data System (ADS)
Mehta, R. D.
Research data on the aerodynamic behavior of baseballs and cricket and golf balls are summarized. Cricket balls and baseballs are roughly the same size and mass but have different stitch patterns. Both are thrown to follow paths that avoid a batter's swing, paths that can curve if aerodynamic forces on the balls' surfaces are asymmetric. Smoke tracer wind tunnel tests and pressure taps have revealed that the unbalanced side forces are induced by tripping the boundary layer on the seam side and producing turbulence. More particularly, the greater pressures are perpendicular to the seam plane and only appear when the balls travel at velocities high enough so that the roughness length matches the seam heigh. The side forces, once tripped, will increase with spin velocity up to a cut-off point. The enhanced lift coefficient is produced by the Magnus effect. The more complex stitching on a baseball permits greater variations in the flight path curve and, in the case of a knuckleball, the unsteady flow effects. For golf balls, the dimples trip the boundary layer and the high spin rate produces a lift coefficient maximum of 0.5, compared to a baseball's maximum of 0.3. Thus, a golf ball travels far enough for gravitational forces to become important.
NASA Technical Reports Server (NTRS)
Mehta, R. D.
1985-01-01
Research data on the aerodynamic behavior of baseballs and cricket and golf balls are summarized. Cricket balls and baseballs are roughly the same size and mass but have different stitch patterns. Both are thrown to follow paths that avoid a batter's swing, paths that can curve if aerodynamic forces on the balls' surfaces are asymmetric. Smoke tracer wind tunnel tests and pressure taps have revealed that the unbalanced side forces are induced by tripping the boundary layer on the seam side and producing turbulence. More particularly, the greater pressures are perpendicular to the seam plane and only appear when the balls travel at velocities high enough so that the roughness length matches the seam heigh. The side forces, once tripped, will increase with spin velocity up to a cut-off point. The enhanced lift coefficient is produced by the Magnus effect. The more complex stitching on a baseball permits greater variations in the flight path curve and, in the case of a knuckleball, the unsteady flow effects. For golf balls, the dimples trip the boundary layer and the high spin rate produces a lift coefficient maximum of 0.5, compared to a baseball's maximum of 0.3. Thus, a golf ball travels far enough for gravitational forces to become important.
Some comments on fuselage drag
NASA Technical Reports Server (NTRS)
Roskam, J.
1975-01-01
The following areas relating to fuselage drag are considered: (1) fuselage fineness - ratio and why and how this can be selected during preliminary design; (2) windshield drag; (3) skin roughness; and (4) research needs in the area of fuselage drag.
NASA Technical Reports Server (NTRS)
Mineck, Raymond Edward
1992-01-01
A comprehensive set of experimental and analytical investigations have been conducted to assess the potential aerodynamic benefits from spanwise blowing at the tip of a moderate aspect ratio, swept wing. An analytical model has been developed to simulate a jet exhausting from the wing tip. An experimental study of a subsonic jet exhausting from the wing tip was conducted to investigate the effect of spanwise blowing from the tip on the aerodynamic characteristics of a moderate aspect ratio, swept wing. Wing force and moment data and surface pressure data were measured at Mach numbers up to 0.72. Results indicate that small amounts of blowing from small jets increase the lift curve slope a small amount, but have no effect on drag. Larger amounts of blowing from longer jets blowing increases lift near the tip and reduce drag at low Mach numbers. These benefits decrease with increasing Mach number, and vanish at Mach 0.5. A Navier-Stokes solver with modified boundary conditions at the tip was used to extrapolate the results to a Mach number of 0.72. With current technology and conventional wing shapes, spanwise blowing at the wing tip does not appear to be a practical means of reducing drag of moderate aspect ratio wings at high subsonic Mach numbers.
The Direct Measurement of Base Drag for Hypersonic Vehicles
NASA Astrophysics Data System (ADS)
Lv, Zhi-guo; Li, Guo-jun; Jiang, Hua; Zhao, Rong-juan; Wang, Gang; Huang, Jun
A new base drag measurement method has been introduced in this paper. In tradition method, the base drag of the model was measured by the pressure transducer located on the bottom of the model. In this method, the base drag was measured with piezoelectric balance directly. The drag force was measured twice by fixing the model base segment to the model or the balance, the difference between these two measurements is considered as the base drag of the model. The wind tunnel test was carried out in φ0.6m shock tunnel of CARDC with a cone model. The base drag of cone model was measured in the flow field of M(=8.42, Re(l=9.67(106/m with the attack angle of 0(. The results showed that the base drag coefficient of the cone model is 0.0015. It means that the base drag can't be ignored in high precision tests, and it can be measured by piezoelectric balance in shock tunnel. The length of the tail sting affects the axis force test result. In the same attack angle, the base drag of high lift/drag ratio model decreases with the increasing of flow field Mach number.
Space Shuttle Orbital Drag Parachute Design
NASA Technical Reports Server (NTRS)
Meyerson, Robert E.
2001-01-01
The drag parachute system was added to the Space Shuttle Orbiter's landing deceleration subsystem beginning with flight STS-49 in May 1992. The addition of this subsystem to an existing space vehicle required a detailed set of ground tests and analyses. The aerodynamic design and performance testing of the system consisted of wind tunnel tests, numerical simulations, pilot-in-the-loop simulations, and full-scale testing. This analysis and design resulted in a fully qualified system that is deployed on every flight of the Space Shuttle.
Effect of longitudinal ridges on the aerodynamic performance of a leatherback turtle model
NASA Astrophysics Data System (ADS)
Bang, Kyeongtae; Kim, Jooha; Kim, Heesu; Lee, Sang-Im; Choi, Haecheon
2012-11-01
Leatherback sea turtles (Dermochelys coriacea) are known as the fastest swimmer and the deepest diver in the open ocean among marine turtles. Unlike other marine turtles, leatherback sea turtles have five longitudinal ridges on their carapace. To investigate the effect of these longitudinal ridges on the aerodynamic performance of a leatherback turtle model, the experiment is conducted in a wind tunnel at Re = 1.0 × 105 - 1.4 × 106 (including that of real leatherback turtle in cruising condition) based on the model length. We measure the drag and lift forces on the leatherback turtle model with and without longitudinal ridges. The presence of longitudinal ridges increases both the lift and drag forces on the model, but increases the lift-to-drag ratio by 15 - 40%. We also measure the velocity field around the model with and without the ridges using particle image velocimetry. More details will be shown in the presentation. Supported by the NRF program (2011-0028032).
NASA Technical Reports Server (NTRS)
Allan, Brian G.; Schaeffler, Norman W.; Jenkins, Luther N.; Yao, Chung-Sheng; Wong, Oliver D.; Tanner, Philip E.
2015-01-01
A rotorcraft fuselage is typically designed with an emphasis on operational functionality with aerodynamic efficiency being of secondary importance. This results in a significant amount of drag during high-speed forward flight that can be a limiting factor for future high-speed rotorcraft designs. To enable higher speed flight, while maintaining a functional fuselage design (i.e., a large rear cargo ramp door), the NASA Rotary Wing Project has conducted both experimental and computational investigations to assess active flow control as an enabling technology for fuselage drag reduction. This paper will evaluate numerical simulations of a flow control system on a generic rotorcraft fuselage with a rotor in forward flight using OVERFLOW, a structured mesh Reynolds-averaged Navier-Stokes flow solver developed at NASA. The results are compared to fuselage forces, surface pressures, and PN flow field data obtained in a wind tunnel experiment conducted at the NASA Langley 14-by 22-Foot Subsonic Tunnel where significant drag and download reductions were demonstrated using flow control. This comparison showed that the Reynolds-averaged Navier-Stokes flow solver was unable to predict the fuselage forces and pressure measurements on the ramp for the baseline and flow control cases. While the CFD was able to capture the flow features, it was unable to accurately predict the performance of the flow control.
Moderate lift-to-drag aeroassist
NASA Technical Reports Server (NTRS)
Florence, D. E.; Fischer, G.
1984-01-01
Significant performance benefits are realized via aerodynamic braking and/or aerodynamic maneuvering on return from higher altitude orbits to low Earth orbit. This approach substantially reduces the mission propellant requirements by using the aerodynamic drag, D, to brake the vehicle to near circular velocity and the aerodynamic lift, L, to null out accumulated errors as well as change the orbital inclination to that required for rendezvous with the Space Shuttle Orbiter. Broad concept evaluations were performed and the technology requirements and sensitivities for aeroassisted OTV's over a range of vehicle hypersonic L/D from 0.75 to 1.5 were systematically identified and assessed. The aeroassisted OTV is capable of evolving from an initial delivery only system to one eventually capable of supporting manned roundtrip missions to geosynchronous orbit. Concept screening was conducted on numerous configurations spanning the L/D = 0.75 to 1.5 range, and several with attractive features were identified. Initial payload capability was evaluated for a baseline of delivery to GEO, six hour polar, and Molniya (12 hours x 63.4 deg) orbits with return and recovery of the aeroassist orbit transfer vehicle (AOTV) at LEO. Evolutionary payload requirements that were assessed include a GEO servicing mission (6K up and 2K return) and a manned GEO mission (14K roundtrip).
Dynamics of Drag Free Formations in Earth Orbit
NASA Technical Reports Server (NTRS)
Ploen, Scott R.; Scharf, Daniel P.; Hadaegh, Fred. Y.; Acikmese, A. Behcet
2004-01-01
In this paper the translational equations of motion of a formation of n spacecraft in Earth orbit, n(sub f) of which are drag-free spacecraft, are derived in a coordinate-free manner using the balance of linear momentum and direct tensor notation. A drag-free spacecraft consists of a spacecraft bus and a proof mass shielded from external disturbances in an internal cavity. By controlling the spacecraft so that the proof mass remains centered in the cavity, the spacecraft follows a purely gravitational orbit. The results described in this paper provide a first step toward coupling drag-free control technology with formation flying in order to mitigate the effect of differential aerodynamic drag on formation flying missions (e.g., Earth imaging applications) in low Earth orbit.
NASA Technical Reports Server (NTRS)
McMillin, S. Naomi (Editor)
1999-01-01
NASA's High-Speed Research Program sponsored the 1998 Aerodynamic Performance Technical Review on February 9-13, in Los Angeles, California. The review was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in areas of Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization), High-Lift, and Flight Controls. The review objectives were to (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientists and engineers working HSCT aerodynamics. In particular, single and multi-point optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT simulation results were presented along with executive summaries for all the Aerodynamic Performance technology areas. The HSR Aerodynamic Performance Technical Review was held simultaneously with the annual review of the following airframe technology areas: Materials and Structures, Environmental Impact, Flight Deck, and Technology Integration. Thus, a fourth objective of the Review was to promote synergy between the Aerodynamic Performance technology area and the other technology areas of the HSR Program.
NASA Technical Reports Server (NTRS)
Hahne, David E. (Editor)
1999-01-01
NASA's High-Speed Research Program sponsored the 1999 Aerodynamic Performance Technical Review on February 8-12, 1999 in Anaheim, California. The review was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in the areas of Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization), High Lift, and Flight Controls. The review objectives were to (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientists and engineers working on HSCT aerodynamics. In particular, single and midpoint optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT simulation results were presented, along with executive summaries for all the Aerodynamic Performance technology areas. The HSR Aerodynamic Performance Technical Review was held simultaneously with the annual review of the following airframe technology areas: Materials and Structures, Environmental Impact, Flight Deck, and Technology Integration. Thus, a fourth objective of the Review was to promote synergy between the Aerodynamic Performance technology area and the other technology areas of the HSR Program. This Volume 1/Part 2 publication covers the design optimization and testing sessions.